[Contamination and ecological risk assessment of polycyclic aromatic hydrocarbons in water and in Karst underground river catchment].

PubMed

Lan, Jia-Cheng; Sun, Yu-Chuan; Tian, Ping; Lu, Bing-Qing; Shi, Yang; Xu, Xin; Liang Zuo-Bing; Yang, Ping-Heng

2014-10-01

Water samples in Laolongdong underground river catchment were collected to determine the concentration, compositional profiles, and evaluate ecological risk of 16 priority polycyclic aromatic hydrocarbons (PAHs). PAHs were measured by GC/MS. The total concentrations of 16 PAH ranged from 81.5-8019 ng · L(-1) in underground river, 288.7-15,200 ng · L(-1) in karst springs, and 128.4-2,442 ng · L(-1) in surface water. Affected by waste water from Huangjueya town, concentrations of PAHs in underground river were higher than those in surface water and waste water from sinkhole. The PAHs profiles were dominated by 3 ring PAHs. There were differences of monthly variations of PAHs contents in the water, due to waste water, season and different characteristics of PAH. Surface water and waste water from sinkhole played an important role on contamination in the river. The levels of ecological risk were generally moderately polluted and heavily polluted according to all detected PAH compounds in the water.

UNDERSTANDING THE FATE OF PETROLEUM HYDROCARBONS IN THE SUBSURFACE ENVIRONMENT

EPA Science Inventory

Sinca a significant number of the two or more million underground storage tank (UST) systems used for petroleum products leak, their cleanup poses a major environmental challenge. Our understnading of the fate of petroleum hydrocarbons in the subsurface environment is critical t...

An Approach that Uses the Concentrations of Hydrocarbon Compounds in Soil Gas at the Source of Contamination to Evaluate the Potential for Intrusion of Petroleum Vapors into Buildings (PVI)

EPA Science Inventory

If motor fuels are spilled from underground storage tanks, petroleum hydrocarbons can vaporize from the spill and move as a vapor through the unsaturated zone. If a building is sited above or near the spill, the hydrocarbons may intrude into the air space of the building. This ...

The bridge permeameter; An alternative method for single-phase, steady-state permeability measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graf, D.C.; Warpinski, N.R.

Laboratory measurements of single-phase, steady-state permeability of porous rock are important for a number of different applications. The oil and gas industry uses permeability data as a key indicator of the producability of a hydrocarbon reservoir; effective containment of large volumes of oil in underground salt caverns is directly dependent upon the permeability of the adjacent cavern walls; and safe, long term underground isolation of radioactive and hazardous waste is contingent upon the flow and transport characteristics of the surrounding geologic formations. An alternative method for measuring single-phase, steady-state permeability of porous rock is presented. The use of troublesome andmore » expensive mass flow meters is eliminated and replaced with a bridge configuration of flow resistors. Permeability values can be determined directly from differential pressures across the bridge network, resulting in potentially significant cost savings and simplification for conducting these types of measurements. Results from the bridge permeameter are compared with results obtained using conventional methods.« less

MODELS AND METHODS FOR PETROLEUM HYDROCARBON RISK ASSESSMENT: ONSITE, LUSTRISK, AND HSSM

EPA Science Inventory

U.S. EPA has developed three tiers of models for analysis of fuel releases from underground storage tank (UST) systems: 1) OnSite; 2) LUSTRisk, and 3) the Hydrocarbon Spill Screening Model (HSSM). The tiered approach to modeling allows users to select a model based upon the amoun...

Aquifers survey in the context of source rocks exploitation: from baseline acquisition to long term monitoring

NASA Astrophysics Data System (ADS)

Garcia, Bruno; Rouchon, Virgile; Deflandre, Jean-Pierre

2017-04-01

Producing hydrocarbons from source rocks (like shales: a mix of clays, silts, carbonate and sandstone minerals containing matured organic matter, i.e. kerogen oil and gas, but also non-hydrocarbon various species of chemical elements including sometimes radioactive elements) requires to create permeability within the rock matrix by at least hydraulically fracturing the source rock. It corresponds to the production of hydrocarbon fuels that have not been naturally expelled from the pressurized matured source rock and that remain trapped in the porosity or/and kerogen porosity of the impermeable matrix. Azimuth and extent of developed fractures can be respectively determined and mapped by monitoring the associated induced microseismicity. This allows to have an idea of where and how far injected fluids penetrated the rock formation. In a geological context, aquifers are always present in the vicinity -or on fluid migration paths- of such shale formations: deep aquifers (near the shale formation) up to sub-surface and potable (surface) aquifers. Our purpose will be to track any unsuitable invasion or migration of chemicals specifies coming from matured shales of production fluids including both drilling and fracturing ones into aquifers. Our objective is to early detect and alarm of any anomaly to avoid any important environmental issue. The approach consists in deploying a specific sampling tool within a well to recover formation fluids and to run a panoply of appropriate laboratory tests to state on fluid characteristics. Of course for deep aquifers, such a characterization process may consider aquifer properties prior producing shale oil and gas, as they may contain naturally some chemical species present in the source rocks. One can also consider that a baseline acquisition could be justified in case of possible previous invasion of non-natural fluids in the formation under survey (due to any anthropogenic action at surface or in the underground). The paper aims at presenting the protocol and routine test we propose to make our early detection approach efficient for production of shale hydrocarbon fluids, in considering the source-rock reservoir itself, the aquifers, and also the chemical species present in the fluids that are used for hydraulic fracturing operations.

How widespread is human-induced seismicity in the USA and Canada?

NASA Astrophysics Data System (ADS)

Van der Baan, M.

2017-12-01

There has been significant public and scientific interest in the observation of changed seismicity rates in North America since 2008, possibly due to human activities. Van der Baan and Calixto (2017) find that the seismicity rate in Oklahoma between 2008 and 2016 is strongly correlated to increased hydrocarbon production. The possibility of systematic correlations between increased hydrocarbon production and seismicity rates is a pertinent question since the USA became the world's largest hydrocarbon producer in 2013, surpassing both Saudi Arabia's oil production and Russia's dry gas production. In most areas increased production is due to systematic hydraulic fracturing which involves high-pressure, underground fluid injection. Increased hydrocarbon production also leads to increased salt-water production which is often disposed of underground. Increased underground fluid injection in general may cause increased seismicity rates due to facilitated slip on pre-existing faults. Contrary to Oklahoma, analysis of oil and gas production versus seismicity rates in six other States in the USA and three provinces in Canada finds no State/Province-wide correlation between increased seismicity and hydrocarbon production, despite 8-16 fold increases in production in some States (Van der Baan and Calixto, 2017). However, in various areas, seismicity rates have increased locally. A comparison with seismic hazard maps shows that human-induced seismicity is less likely in areas that have historically felt fewer earthquakes. The opposite is not necessarily true. ReferencesVan der Baan, M. and Calixto, F. J. (2017), Human-induced seismicity and large-scale hydrocarbon production in the USA and Canada. Geochem. Geophys. Geosyst., 18, doi:10.1002/2017GC006915 AcknowledgmentsThe author thanks Frank Calixto who co-authored the paper on which a large portion of this lecture is based, the sponsors of the Microseismic Industry Consortium for financial support, the SEG for funding and organizing the SEG 2017 Honorary Lecturer tour, North America, and the organizers of this session, sponsored by the AGU Near Surface Geophysics and Seismology Divisions, for inviting him to give this presentation.

An Approach for Developing Site-Specific Lateral and Vertical Inclusion Zones within which Structures Should be Evaluated for Petroleum Vapor Intrusion due to Releases of Motor Fuel from Underground Storage Tanks

EPA Science Inventory

Buildings may be at risk from Petroleum Vapor Intrusion (PVI) when they overlie petroleum hydrocarbon contamination in the unsaturated zone or dissolved in groundwater. The U.S. EPA Office of Underground Storage Tanks (OUST) is preparing Guidance for Addressing Petroleum Vapor I...

In situ bioremediation of an underground diesel fuel spill: A case history

NASA Astrophysics Data System (ADS)

Frankenberger, W. T.; Emerson, K. D.; Turner, D. W.

1989-05-01

In the winter months of 1983, approximately 1000 gallons of diesel fuel had flowed along an asphalt parking lot of a commercial establishment towards a surface drain near an open creek. Investigations led to the discovery of an underground storage tank leaking diesel fuel. Exploratory borings showed that contamination was near the surface horizon and the capillary zone of the water table. Hydrocarbon quantities ranged up to 1500 mg/kg of soil. The plume continued to move in an eastward direction toward the surface water of the creek. A laboratory study indicated relatively high numbers of hydrocarbon-oxidizing organisms relative to glucose-utilizing microorganisms in the unsaturated vadose zone. Bioreclamation was initiated in April 1984 by injecting nutrients (nitrogen and phosphorus) and hydrogen peroxide and terminated in October 1984 upon no detection (<1 mg/kg) of hydrocarbons. A verification boring within the vicinity of the contaminated plume confirmed that residual contamination had attained background levels. The monitoring program was terminated in January 1987.

31 CFR 561.318 - Petroleum.

Code of Federal Regulations, 2012 CFR

2012-07-01

... § 561.318 Petroleum. A mixture of hydrocarbons that exists in liquid phase in natural underground reservoirs and remains liquid at atmospheric pressure after passing through surface separating facilities...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, G.R.B.; Vanderborgh, N.E.

Experimental and theoretical analyses show that uncontrolled water invasion during underground coal conversion (UCC) is harmful at all stages of UCC. By contrast, if water invasion is prevented, coal porosity can be created for further processing, pyrolysis can yield uniform hydrocarbon products, gasification can produce a uniform product, coal is fully consumed (not bypassed) during combustion, and environmental problems are minimized. In all cases the experimental results are supportive of the theory of underground coal processing presented. We see no insurmountable technical problems existing for a staged underground coal conversion process, but we emphasize that all concepts in underground coalmore » processing depend critically upon control of water influx. It is important that techniques for measuring and controlling water flow be developed if this technology is to make a contribution to the Nation's energy supply.« less

Reconnaissance investigations of potential ground-water and sediment contamination at three former underground storage tank locations, Fort Jackson, South Carolina, 1994

USGS Publications Warehouse

Robertson, J.F.; Nagle, Douglas D.; Rhodes, Liesl C.

1994-01-01

Investigations to provide initial qualitative delineation of petroleum hydrocarbon contamination at three former underground storage tank locations at Fort Jackson, South Carolina, were made during March 1994. Ground-water and sediment samples were collected using direct-push technology and analyzed on-site with a gas chromatograph, which provided real-time, semi-quantitative data. In addition, ground-water and sediment samples were collected at selected sites for laboratory analyses to provide a confirmation of the on-site data. These analyses provided qualitative data on the lateral distri- bution of petroleum hydrocarbons. Petroleum hydrocarbons were detected by on-site analysis in ground-water samples from nine locations at Site 1062, suggesting the presence of a contaminant plume. Concentrations ranged from less than the minimum detection limit to 4,511 mg/L (micrograms per liter) for benzene, 15,594 mg/L for toluene, 16,501 mg/L for ethylbenzene, and 19,391 mg/L for total xylenes. Concentrations of Total Petroleum Hydrocarbons-Gasoline Range Organics ranged from 323 mg/L to 3,364 mg/L; Total Petroleum Hydrocarbons-Diesel Range Organics were not detected. Three samples from this site were analyzed for benzene, toluene, ethylbenzene, and total xylenes at a laboratory and results showed concentrations ranging from less than the minimum detection limit to 1,070 mg/L for benzene, 7,930 mg/L for toluene, 6,890 mg/L for ethylbenzene, and 1,524 mg/L for total xylenes. Petroleum hydro- carbons were detected by on-site analysis in only one sample at Site 2438. A concentration of 131,000 micrograms per kilogram Total Petroleum Hydrocarbons-Diesel Range Organics was detected in sample number GP-2-4-13.5. Petroleum hydrocarbons were detected by on-site analysis in only one ground-water sample from Site 2444. A concentration of 3,145 mg/L Total Petroleum Hydrocarbons-Gasoline Range Organics was detected at sampling location GP-3-2.

In situ heat treatment of a tar sands formation after drive process treatment

DOEpatents

Vinegar, Harold J.; Stanecki, John

2010-09-21

A method for treating a tar sands formation includes providing a drive fluid to a hydrocarbon containing layer of the tar sands formation to mobilize at least some hydrocarbons in the layer. At least some first hydrocarbons from the layer are produced. Heat is provided to the layer from one or more heaters located in the formation. At least some second hydrocarbons are produced from the layer of the formation. The second hydrocarbons include at least some hydrocarbons that are upgraded compared to the first hydrocarbons produced by using the drive fluid.

Soil cover of gas-bearing areas

NASA Astrophysics Data System (ADS)

Mozharova, N. V.

2010-08-01

Natural soils with disturbed functioning parameters compared to the background soils with conservative technogenic-pedogenic features were distinguished on vast areas above the artificial underground gas storages in the zones of spreading and predominant impact of hydrocarbon gases. The disturbance of the functioning parameters is related to the increase in the methane concentration, the bacterial oxidation intensity and destruction, and the complex microbiological and physicochemical synthesis of iron oxides. The technogenic-pedogenic features include neoformations of bacteriomorphic microdispersed iron oxides. The impurity components consist of elements typical for biogenic structures. New soil layers, horizons, specific anthropogenically modified soils, and soil-like structures were formed on small areas in the industrial zones of underground gas storages due to the mechanical disturbance, the deposition of drilling sludge, and the chemical contamination. Among the soils, postlithogenic formations were identified—chemotechnosols (soddy-podzolic soils and chernozems), as well as synlithogenic ones: strato-chemotechnosols and stratochemoembryozems. The soil-like bodies included postlithogenic soil-like structures (chemotechnozems) and synlithogenic ones (strato-chemotechnozems). A substantive approach was used for the soil diagnostics. The morphological and magnetic profiles and the physical, chemical, and physicochemical properties of the soils were analyzed. The micromorphological composition of the soil magnetic fraction was used as a magnetic label.

Assessment of petroleum-hydrocarbon contamination in the surficial sediments and ground water at three former underground storage tank locations, Fort Jackson, South Carolina, 1995

USGS Publications Warehouse

Robertson, J.F.

1996-01-01

Ground-water and sediment contamination by petroleum hydrocarbons resulting from leaks and overfills was detected during tank removal activities at three former underground storage tank locations at Fort Jackson, near Columbia, South Carolina. Investigations were initiated to assess the effect of contamination to the surficial aquifer at Sites 1062, 2438, and 2444. These investigations involved the installation of permanent monitoring wells and the collection and analysis of sediment and ground-water samples at the three sites. Water-level data were collected at all sites to determine hydraulic gradients and the direction of ground-water flow. In addition, aquifer tests were made at Site 1062 to determine the hydraulic conductivity of the surficial aquifer at that site. Sediment borings were made at the three sites to collect subsurface-sediment samples for lithologic description and laboratory analyses, and for the installation of ground-water monitoring wells. Laboratory analyses of sediment samples collected from boreholes at Site 1062 indicated elevated concentrations of petroleum hydrocarbons at three locations. Total Petroleum Hydrocarbons - Diesel Range Organics were detected at one borehole at a concentration of 388,000 micrograms per kilogram. Total benzene, toluene, ethylbenzene, and xylene concentrations in sediment from the site ranged from less than 350 to over 100,000 micrograms per kilogram. Total lead was detected at concentrations ranging from 2,900 to 5,900 micrograms per kilogram. Petroleum hydrocarbons were detected at Site 2438 in one borehole at a trace concentration of 112 micrograms per kilogram of para- and meta-xylenes. No concentrations exceeding the detection limits were reported for petroleum hydrocarbons in sediment samples collected from Site 2444; however, total lead was detected in sediment samples from two boreholes, each at concentrations of 600 micrograms per kilogram. Ground-water samples were collected from each site for laboratory analysis and field-property determinations. Petroleum hydrocarbons and lead were detected at concentrations exceeding regulatory limits for drinking water in ground water from Site 1062 only. Petroleum hydrocarbons were detected in ground water from three wells at Site 1062, with the highest concentrations occurring in the area of the former underground storage tanks. Benzene was detected at concentrations as much as 28 micrograms per liter; toluene as much as 558 micrograms per liter; para- and meta-xylenes as much as 993 micrograms per liter; and naphthalene as much as 236 micrograms per liter. Ethylbenzene and ortho-xylene were detected in one well at concentrations of 70 and 6 micrograms per liter, respectively. Dissolved lead was detected in ground water from four wells at concentrations from 5 to 152 micrograms per liter. Analysis of ground-water samples collected from Sites 2438 and 2444 showed little evidence of petroleum-hydrocarbon contamination. Petroleum hydrocarbons were not detected in any of the ground-water samples collected from Site 2438. With the exception of a low concentration of naphthalene (11 micrograms per liter) detected in ground water from one well, petroleum hydrocarbons and lead were not detected in ground water collected from Site 2444.

Human-induced seismicity and large-scale hydrocarbon production in the USA and Canada

NASA Astrophysics Data System (ADS)

van der Baan, Mirko; Calixto, Frank J.

2017-07-01

We compare current and historic seismicity rates in six States in the USA and three Provinces in Canada to past and present hydrocarbon production. All States/Provinces are major hydrocarbon producers. Our analyses span three to five decades depending on data availability. Total hydrocarbon production has significantly increased in the past few years in these regions. Increased production in most areas is due to large-scale hydraulic fracturing and thus underground fluid injection. Furthermore, increased hydrocarbon production generally leads to increased water production, which must be treated, recycled, or disposed of underground. Increased fluid injection enhances the likelihood of fault reactivation, which may affect current seismicity rates. We find that increased seismicity in Oklahoma, likely due to salt-water disposal, has an 85% correlation with oil production. Yet, the other areas do not display State/Province-wide correlations between increased seismicity and production, despite 8-16-fold increases in production in some States. However, in various cases, seismicity has locally increased. Multiple factors play an important role in determining the likelihood of anthropogenic activities influencing earthquake rates, including (i) the near-surface tectonic background rate, (ii) the existence of critically stressed and favorably oriented faults, which must be hydraulically connected to injection wells, (iii) the orientation and magnitudes of the in situ stress field, combined with (iv) the injection volumes and implemented depletion strategies. A comparison with the seismic hazard maps for the USA and Canada shows that induced seismicity is less likely in areas with a lower hazard. The opposite, however, is not necessarily true.

40 CFR 264.18 - Location standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... affected surface waters or the soils of the 100- year floodplain that could result from washout. [Comment... dome formations, salt bed formations, underground mines and caves. The placement of any noncontainerized or bulk liquid hazardous waste in any salt dome formation, salt bed formation, underground mine or...

40 CFR 264.18 - Location standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... affected surface waters or the soils of the 100- year floodplain that could result from washout. [Comment... dome formations, salt bed formations, underground mines and caves. The placement of any noncontainerized or bulk liquid hazardous waste in any salt dome formation, salt bed formation, underground mine or...

40 CFR 264.18 - Location standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... affected surface waters or the soils of the 100- year floodplain that could result from washout. [Comment... dome formations, salt bed formations, underground mines and caves. The placement of any noncontainerized or bulk liquid hazardous waste in any salt dome formation, salt bed formation, underground mine or...

In situ heat treatment from multiple layers of a tar sands formation

DOEpatents

Vinegar, Harold J.

2010-11-30

A method for treating a tar sands formation is disclosed. The method includes providing a drive fluid to a first hydrocarbon containing layer of the formation to mobilize at least some hydrocarbons in the first layer. At least some of the mobilized hydrocarbons are allowed to flow into a second hydrocarbon containing layer of the formation. Heat is provided to the second layer from one or more heaters located in the second layer. At least some hydrocarbons are produced from the second layer of the formation.

TANK ISSUES: DESIGN AND PLACEMENT OF FLOATING LIQUID MONITORING WELLS

EPA Science Inventory

Liquid product monitoring is the predominant method of external leak detection where the water table is within the zone of excavation. his paper discusses the use of liquid product monitors at new and old tank installations for detecting leaks from underground hydrocarbon storage...

INTERNET COURSE ON MODELING SUBSURFACE TRANSPORT OF PETROLEUM HYDROCARBONS

EPA Science Inventory

Assessment of leaks from underground storage tanks relies on knowledge of contaminant fate and transport, hydrology and in some cases modeling. EPA is developing an interactive, on-line training course to provide states with a low-cost training opportunity for these areas. Two ...

Moving hydrocarbons through portions of tar sands formations with a fluid

DOEpatents

Stegemeier, George Leo; Mudunuri, Ramesh Raju; Vinegar, Harold J.; Karanikas, John Michael; Jaiswal, Namit; Mo, Weijian

2010-05-18

A method for treating a tar sands formation is disclosed. The method includes heating a first portion of a hydrocarbon layer in the formation from one or more heaters located in the first portion. The heat is controlled to increase a fluid injectivity of the first portion. A drive fluid and/or an oxidizing fluid is injected and/or created in the first portion to cause at least some hydrocarbons to move from a second portion of the hydrocarbon layer to a third portion of the hydrocarbon layer. The second portion is between the first portion and the third portion. The first, second, and third portions are horizontally displaced from each other. The third portion is heated from one or more heaters located in the third portion. Hydrocarbons are produced from the third portion of the formation. The hydrocarbons include at least some hydrocarbons from the second portion of the formation.

In situ sensing of subsurface contamination--part I: near-infrared spectral characterization of alkanes, aromatics, and chlorinated hydrocarbons.

PubMed

Klavarioti, Maria; Kostarelos, Konstantinos; Pourjabbar, Anahita; Ghandehari, Masoud

2014-05-01

There is an imperative need for a chemical sensor capable of remote, in situ, long-term monitoring of chemical species at sites containing toxic chemical spills, specifically at chemical waste dumps, landfills, and locations with underground storage tanks. In the current research, a series of experiments were conducted measuring the near-infrared optical absorption of alkanes, aromatics, and chlorinated hydrocarbons. A spectral library was then developed to characterize the optical spectra of liquid hydrocarbons. Near-infrared analysis was chosen due to compatibility with optical fibers. The goal was to differentiate between classes of hydrocarbons and to also discriminate between compounds within a class of similar molecular structures. It was observed that unique absorption spectra can be obtained for each hydrocarbon, and this uniqueness can be used to discriminate between hydrocarbons from different families. Statistical analyses, namely, principal component analysis (PCA) and correlation coefficient (Spearman and Pearson methods), were attempted to match absorption spectra from an unknown hydrocarbon with the database with limited success. An algorithm was subsequently written to identify the characteristic peaks of each hydrocarbon that could be used to match data from an unknown chemical species with the database.

Effect of permafrost properties on gas hydrate petroleum system in the Qilian Mountains, Qinghai, Northwest China.

PubMed

Wang, Pingkang; Zhang, Xuhui; Zhu, Youhai; Li, Bing; Huang, Xia; Pang, Shouji; Zhang, Shuai; Lu, Cheng; Xiao, Rui

2014-12-01

The gas hydrate petroleum system in the permafrost of the Qilian Mountains, which exists as an epigenetic hydrocarbon reservoir above a deep-seated hydrocarbon reservoir, has been dynamic since the end of the Late Pleistocene because of climate change. The permafrost limits the occurrence of gas hydrate reservoirs by changing the pressure-temperature (P-T) conditions, and it affects the migration of the underlying hydrocarbon gas because of its strong sealing ability. In this study, we reconstructed the permafrost structure of the Qilian Mountains using a combination of methods and measured methane permeability in ice-bearing sediment permafrost. A relationship between the ice saturation of permafrost and methane permeability was established, which permitted the quantitative evaluation of the sealing ability of permafrost with regard to methane migration. The test results showed that when ice saturation is >80%, methane gas can be completely sealed within the permafrost. Based on the permafrost properties and genesis of shallow gas, we suggest that a shallow "gas pool" occurred in the gas hydrate petroleum system in the Qilian Mountains. Its formation was related to a metastable gas hydrate reservoir controlled by the P-T conditions, sealing ability of the permafrost, fault system, and climatic warming. From an energy perspective, the increasing volume of the gas pool means that it will likely become a shallow gas resource available for exploitation; however, for the environment, the gas pool is an underground "time bomb" that is a potential source of greenhouse gas.

Cogeneration systems and processes for treating hydrocarbon containing formations

DOEpatents

Vinegar, Harold J [Bellaire, TX; Fowler, Thomas David [Houston, TX; Karanikas, John Michael [Houston, TX

2009-12-29

A system for treating a hydrocarbon containing formation includes a steam and electricity cogeneration facility. At least one injection well is located in a first portion of the formation. The injection well provides steam from the steam and electricity cogeneration facility to the first portion of the formation. At least one production well is located in the first portion of the formation. The production well in the first portion produces first hydrocarbons. At least one electrical heater is located in a second portion of the formation. At least one of the electrical heaters is powered by electricity from the steam and electricity cogeneration facility. At least one production well is located in the second portion of the formation. The production well in the second portion produces second hydrocarbons. The steam and electricity cogeneration facility uses the first hydrocarbons and/or the second hydrocarbons to generate electricity.

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fuel oil requirements for ANFO. 57.6309 Section 57.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels...

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuel oil requirements for ANFO. 57.6309 Section 57.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels...

ASSESSING UST CORRECTIVE ACTION TECHNOLOGIES: IN SITU SVE-BASED SYSTEMS FOR FREE PRODUCT RECOVERY AND RESIDUAL HYDROCARBON REMOVAL

EPA Science Inventory

The number of confirmed releases of petroleum products from underground storage tank (UST) systems has increased significantly since promulgation of the final UST regulations by the U.S. Environmental Protection Agency in December 1988. This increase has outpaced the resources of...

Using Concentrations of Methane and Gasoline Hydrocarbons in Soil Gas to Predict Vapor Intrusion of Benzene

EPA Science Inventory

Risk management of petroleum vapor intrusion has been a daunting and challenging task for the Underground Storage Tank Program. Because chlorinated solvents do not degrade in soil gas, techniques that focus on their properties and behavior can produce useful estimates. However, t...

Anaerobic Biodegradation of Ethylene Dibromide and 1,2-Dichloroethane in the Presence of Fuel Hydrocarbons

EPA Science Inventory

Field evidence from underground storage tank sites where leaded gasoline leaked indicates the lead scavengers 1,2- dibromoethane (ethylene dibromide, or EDB) and 1,2- dichloroethane (1,2-DCA) may be present in groundwater at levels that pose unacceptable risk. These compounds are...

Bioremediation Of Groundwater Contaminated Wtih Gasoline Hydrocarbons And Oxygenates Using A Membrane-Based Reactor

EPA Science Inventory

The objective of this study was to operate a novel, field-scale, aerobic bioreactor and assess its performance in the ex situ treatment of groundwater contaminated with gasoline from a leaking underground storage tank in Pascoag, RI. The groundwater contained elevated concentrat...

A comparison of the rates of hydrocarbon generation from Lodgepole, False Bakken, and Bakken formation petroleum source rocks, Williston Basin, USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarvie, D.M.; Elsinger, R.J.; Inden, R.F.

1996-06-01

Recent successes in the Lodgepole Waulsortian Mound play have resulted in the reevaluation of the Williston Basin petroleum systems. It has been postulated that hydrocarbons were generated from organic-rich Bakken Formation source rocks in the Williston Basin. However, Canadian geoscientists have indicated that the Lodgepole Formation is responsible for oil entrapped in Lodgepole Formation and other Madison traps in portions of the Canadian Williston Basin. Furthermore, geoscientists in the U.S. have recently shown oils from mid-Madison conventional reservoirs in the U.S. Williston Basin were not derived from Bakken Formation source rocks. Kinetic data showing the rate of hydrocarbon formation frommore » petroleum source rocks were measured on source rocks from the Lodgepole, False Bakken, and Bakken Formations. These results show a wide range of values in the rate of hydrocarbon generation. Oil prone facies within the Lodgepole Formation tend to generate hydrocarbons earlier than the oil prone facies in the Bakken Formation and mixed oil/gas prone and gas prone facies in the Lodgepole Formation. A comparison of these source rocks using a geological model of hydrocarbon generation reveals differences in the timing of generation and the required level of maturity to generate significant amounts of hydrocarbons.« less

Petroleum exploration in Africa from space

NASA Astrophysics Data System (ADS)

Gianinetto, Marco; Frassy, Federico; Aiello, Martina; Rota Nodari, Francesco

2017-10-01

Hydrocarbons are nonrenewable resources but today they are the cheaper and easier energy we have access and will remain the main source of energy for this century. Nevertheless, their exploration is extremely high-risk, very expensive and time consuming. In this context, satellite technologies for Earth observation can play a fundamental role by making hydrocarbon exploration more efficient, economical and much more eco-friendly. Complementary to traditional geophysical methods such as gravity and magnetic (gravmag) surveys, satellite remote sensing can be used to detect onshore long-term biochemical and geochemical alterations on the environment produced by invisible small fluxes of light hydrocarbons migrating from the underground deposits to the surface, known as microseepage effect. This paper describes two case studies: one in South Sudan and another in Mozambique. Results show how remote sensing is a powerful technology for detecting active petroleum systems, thus supporting hydrocarbon exploration in remote or hardly accessible areas and without the need of any exploration license.

Treating tar sands formations with dolomite

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael

2010-06-08

Methods for treating a tar sands formation are described herein. The tar sands formation may include dolomite and hydrocarbons. Methods may include providing heat at less than the decomposition temperature of dolomite from one or more heaters to at least a portion of the formation. At least some of the hydrocarbon fluids are mobilized in the formation. At least some of the hydrocarbon fluids may be produced from the formation.

Dry and stable excavations in limestones of the greater Kansas City area of Missouri and Kansas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goebel, E.D.; Parizek, E.J.; Stauffer, T.P.

In the Greater Kansas City area of Missouri and Kansas the bedrock consists largely of a thick sequence of limestone and shale formations of Pennsylvanian age. Three formations are of interest in this report. The Swope Formation contains the Bethany Falls Limestone, the Wyandotte Formation contains the Argentine Limestone and the Farley Limestone, and the Oread Formation contains the Plattsmouth Limestone. Underground workings have been developed by industry in these three formations for a variety of uses, including factories, offices and warehouses. The Bethany Falls Limestone is the unit most widely developed for secondary underground use. The industries which design,more » excavate, and occupy this man-made underground space consider it to be essentially dry and stable. Identification and description of the geologic, topographic, hydrologic, and possible other unique features which allow this operational decision is the primary goal of this investigation.« less

Systems and methods for producing hydrocarbons from tar sands formations

DOEpatents

Li, Ruijian [Katy, TX; Karanikas, John Michael [Houston, TX

2009-07-21

A system for treating a tar sands formation is disclosed. A plurality of heaters are located in the formation. The heaters include at least partially horizontal heating sections at least partially in a hydrocarbon layer of the formation. The heating sections are at least partially arranged in a pattern in the hydrocarbon layer. The heaters are configured to provide heat to the hydrocarbon layer. The provided heat creates a plurality of drainage paths for mobilized fluids. At least two of the drainage paths converge. A production well is located to collect and produce mobilized fluids from at least one of the converged drainage paths in the hydrocarbon layer.

Single well tracer method to evaluate enhanced recovery

DOEpatents

Sheely, Jr., Clyde Q.; Baldwin, Jr., David E.

1978-01-01

Data useful to evaluate the effectiveness of or to design an enhanced recovery process (the recovery process involving mobilizing and moving hydrocarbons through a hydrocarbon-bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well) are obtained by a process which comprises sequentially: determining hydrocarbon saturation in the formation in a volume in the formation near a well bore penetrating the formation, injecting sufficient of the mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore penetrating the formation, and determining by the single well tracer method a hydrocarbon saturation profile in a volume from which hydrocarbons are moved. The single well tracer method employed is disclosed by U.S. Pat. No. 3,623,842. The process is useful to evaluate surfactant floods, water floods, polymer floods, CO.sub.2 floods, caustic floods, micellar floods, and the like in the reservoir in much less time at greatly reduced costs, compared to conventional multi-well pilot test.

Catalytic copyrolysis of cork oak and bio-oil distillation residue

NASA Astrophysics Data System (ADS)

Lee, Yejin; Oh, Daejun; Kim, Young-Min; Jae, Jungho; Jung, Sang-Chul; Jeon, Jong-Ki; Kim, Sang Chai; Park, Young-Kwon

2018-01-01

The atmospheric distillation residue (ADR) of cork oak (CO) pyrolysis oil was used as the co-feeding material for the catalytic pyrolysis of CO over HZSM-5 catalysts to improve the formation of aromatic hydrocarbons. Although the non-catalytic copyrolysis of CO and ADR did not improve the formation of aromatic hydrocarbons, the catalytic copyrolysis of CO and ADR promoted the synergistic formation of aromatic hydrocarbons. HZSM-5(30), having a lower SiO2/Al2O3(30), showed better performance for the formation of aromatic hydrocarbons than HZSM-5(80) because of its higher acidity. The catalytic copyrolysis of CO and ADR also decreased the formation of coke. The largest quantity of aromatic hydrocarbons was obtained from the catalytic copyrolysis of CO and ADR over HZSM-5 (30) at 600 °C, whereas the lowest coke yield was achieved at 700 °C. When the catalyst to sample ratio was increased from 2:1 to 5:1, the synergistic formation of aromatic hydrocarbons was limited, resulting in a lower experimental yield of aromatic hydrocarbons than the theoretical yield. A lower coke yield was also achieved at a high catalyst to sample ratio (5:1).

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

Investigation of Underground Hydrocarbon Leakage using Ground Penetrating Radar

NASA Astrophysics Data System (ADS)

Srigutomo, Wahyu; Trimadona; Agustine, Eleonora

2016-08-01

Ground Penetrating Radar (GPR) survey was carried out in several petroleum plants to investigate hydrocarbon contamination beneath the surface. The hydrocarbon spills are generally recognized as Light Non-Aqueous Phase Liquids (LNAPL) if the plume of leakage is distributed in the capillary fringe above the water table and as Dense Non-Aqueous Phase Liquids (DNAPL) if it is below the water table. GPR antennas of 200 MHz and 400 MHz were deployed to obtain clear radargrams until 4 m deep. In general, the interpreted radargram sections indicate the presence of surface concrete layer, the compacted silty soill followed by sand layer and the original clayey soil as well as the water table. The presence of hydrocarbon plumes are identified as shadow zones (radar velocity and intensity contrasts) in the radargram that blur the layering pattern with different intensity of reflected signal. Based on our results, the characteristic of the shadow zones in the radargram is controlled by several factors: types of hydrocarbon (fresh or bio-degraded), water moisture in the soil, and clay content which contribute variation in electrical conductivity and dielectric constants of the soil.

Heating hydrocarbon containing formations in a line drive staged process

DOEpatents

Miller, David Scott [Katy, TX

2009-07-21

Method for treating a hydrocarbon containing formation are described herein. Methods may include providing heat to a first section of the formation with one or more first heaters in the first section. First hydrocarbons may be heated in the first section such that at least some of the first hydrocarbons are mobilized. At least some of the mobilized first hydrocarbons may be produced through a production well located in a second section of the formation. The second section may be located substantially adjacent to the first section. A portion of the second section may be provided some heat from the mobilized first hydrocarbons, but is not conductively heated by heat from the first heaters. Heat may be provided to the second section with one or more second heaters in the second section to further heat the second section.

Long-period Seismicity at the Napoleonville Salt Dome: Implications for Local Seismic Monitoring of Underground Hydrocarbon Storage Caverns

NASA Astrophysics Data System (ADS)

Dreger, D. S.; Ford, S. R.; Nayak, A.

2015-12-01

The formation of a large sinkhole at the Napoleonville salt dome, Assumption Parish, Louisiana, in August 2012 was accompanied by a rich sequence of complex seismic events, including long-period (LP) events that were recorded 11 km away at Transportable Array station 544A in White Castle, Louisiana. The LP events have relatively little energy at short periods, which make them difficult to detect using standard high-frequency power detectors, and the majority of energy that reaches the station is peaked near 0.4 Hz. The analysis of the local records reveals that the onset of the 0.4 Hz signals coincides with the S-wave arrival, and therefore it may be a shaking induced resonance in a fluid filled cavern. We created a low-frequency (0.1-0.6 Hz) power detector (short-term average / long-term average) that operated on all three components of the broadband instrument, since considerable energy was detected on the horizontal components. The detections from the power detector were then used as templates in three-channel correlation detectors thereby increasing the number of detections by a little more than a factor of two to nearly 3000. The rate of LP events is approximately one event every other day at the beginning of recording in March 2011. Around 2 May 2012 the rate changes to approximately 7 events per day and then increases to 25 events per day at the beginning of July 2012. Finally, in the days leading up to the sinkhole formation there are approximately 200 LP events per day. The analysis of these events could aid in the development of local seismic monitoring methods for underground industrial storage caverns. Prepared by LLNL under Contract DE-AC52-07NA27344.

Cost Effective, Ultra Sensitive Groundwater Monitoring for Site Remediation and Management

DTIC Science & Technology

2015-05-01

feasibility studies. ................... 30  Table 5. Compounds screened in the laboratory for IS2 sampling...tank SVOC semivolatile organic compound TCE trichloroethene TPH total petroleum hydrocarbon USEPA U.S. Environmental Protection Agency UST...underground storage tank V volt VOA volatile organic analysis VOC volatile organic compound Technical material contained in this report has

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fuel oil requirements for ANFO. 57.6309 Section... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels with flash points lower than that of No. 2 diesel oil (125 °F) shall not be used to prepare ammonium...

Aromatic ring generation as a dust precursor in acetylene discharges

NASA Astrophysics Data System (ADS)

De Bleecker, Kathleen; Bogaerts, Annemie; Goedheer, Wim

2006-04-01

Production of aromatic hydrocarbon compounds as an intermediate step for particle formation in low-pressure acetylene discharges is investigated via a kinetic approach. The detailed chemical reaction mechanism contains 140 reactions among 55 species. The cyclic hydrocarbon chemistry is mainly based on studies of polycyclic aromatic hydrocarbon formation in cosmic environments. The model explicitly includes organic chain, cyclic molecules, radicals, and ions up to a size of 12 carbon atoms. The calculated density profiles show that the aromatic formation yields are quite significant, suggesting that aromatic compounds play a role in the underlying mechanisms of particle formation in hydrocarbon plasmas.

Heating tar sands formations to visbreaking temperatures

DOEpatents

Karanikas, John Michael [Houston, TX; Colmenares, Tulio Rafael [Houston, TX; Zhang, Etuan [Houston, TX; Marino, Marian [Houston, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Beer, Gary Lee [Houston, TX; Dombrowski, Robert James [Houston, TX; Jaiswal, Namit [Houston, TX

2009-12-22

Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat may be controlled so that at least a majority of the section reaches an average temperature of between 200.degree. C. and 240.degree. C., which results in visbreaking of at least some hydrocarbons in the section. At least some visbroken hydrocarbon fluids may be produced from the formation.

Role of methyl group number on SOA formation from aromatic hydrocarbons photooxidation under low NOx conditions

NASA Astrophysics Data System (ADS)

Li, L.; Tang, P.; Nakao, S.; Chen, C.-L.; Cocker, D. R., III

2015-11-01

Substitution of methyl groups onto the aromatic ring determines the SOA formation from the aromatic hydrocarbon precursor. This study links the number of methyl groups on the aromatic ring to SOA formation from aromatic hydrocarbons photooxidation under low NOx conditions (HC / NO > 10 ppb C : ppb). Aromatic hydrocarbons with increasing numbers of methyl groups are systematically studied. SOA formation from pentamethylbenzene and hexamethylbenzene are reported for the first time. A decreasing SOA yield with increasing number of methyl groups is observed. Linear trends are found in both f44 vs. f43 and O / C vs. H / C for SOA from aromatic hydrocarbons with zero to six methyl groups. An SOA oxidation state predictive method based on benzene is used to examine the effect of added methyl groups on aromatic oxidation under low NOx conditions. Further, the impact of methyl group number on density and volatility of SOA from aromatic hydrocarbons is explored. Finally, a mechanism for methyl group impact on SOA formation is suggested. Overall, this work suggests as more methyl groups are attached on the aromatic ring, SOA products from these aromatic hydrocarbons become less oxidized per mass/carbon.

Cost-Effective, Ultra-Sensitive Groundwater Monitoring for Site Remediation and Management

DTIC Science & Technology

2015-05-01

Example anion concentrations in groundwater used for feasibility studies. ................... 30 Table 5. Compounds screened in the laboratory for IS2...phase extraction ST storage tank SVOC semivolatile organic compound TCE trichloroethene TPH total petroleum hydrocarbon USEPA U.S. Environmental...Protection Agency UST underground storage tank V volt VOA volatile organic analysis VOC volatile organic compound Technical material

40 CFR Table W - 4 of Subpart W of Part 98-Default Total Hydrocarbon Emission Factors for Underground Natural Gas...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Population Emission Factors—Storage Wellheads, Gas Service Connector 0.01 Valve 0.1 Pressure Relief Valve 0.17 Open Ended Line 0.03 Population Emission Factors—Other Components, Gas Service Low Continuous... Bleed Pneumatic Device Vents 2 2.35 1 Valves include control valves, block valves and regulator valves...

40 CFR Table W - 4 of Subpart W-Default Total Hydrocarbon Emission Factors for Underground Natural Gas Storage

Code of Federal Regulations, 2012 CFR

2012-07-01

... Connector 5.59 Open-Ended Line 17.27 Pressure Relief Valve 39.66 Meter 19.33 Population Emission Factors... Population Emission Factors—Other Components, Gas Service Low Continuous Bleed Pneumatic Device Vents 2 1.37... Valves include control valves, block valves and regulator valves. 2 Emission Factor is in units of “scf...

40 CFR Table W - 4 of Subpart W of Part 98-Default Total Hydrocarbon Emission Factors for Underground Natural Gas...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Population Emission Factors—Storage Wellheads, Gas Service Connector 0.01 Valve 0.1 Pressure Relief Valve 0.17 Open Ended Line 0.03 Population Emission Factors—Other Components, Gas Service Low Continuous... Bleed Pneumatic Device Vents 2 2.35 1 Valves include control valves, block valves and regulator valves...

Method of producing drive fluid in situ in tar sands formations

DOEpatents

Mudunuri, Ramesh Raju; Jaiswal, Namit; Vinegar, Harold J.; Karanikas, John Michael

2010-03-23

Methods of treating a tar sands formation are described herein. Methods for treating a tar sands may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. The heat may be allowed to transfer from the heaters to at least a portion of the formation such that a drive fluid is produced in situ in the formation. The drive fluid may move at least some mobilized, visbroken, and/or pyrolyzed hydrocarbons from a first portion of the formation to a second portion of the formation. At least some of the mobilized, visbroken, and/or pyrolyzed hydrocarbons may be produced from the formation.

Heating tar sands formations while controlling pressure

DOEpatents

Stegemeier, George Leo [Houston, TX; Beer, Gary Lee [Houston, TX; Zhang, Etuan [Houston, TX

2010-01-12

Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. A pressure in the majority of the section may be maintained below a fracture pressure of the formation. The pressure in the majority of the section may be reduced to a selected pressure after the average temperature reaches a temperature that is above 240.degree. C. and is at or below pyrolysis temperatures of hydrocarbons in the section. At least some hydrocarbon fluids may be produced from the formation.

In-situ process for recovering hydrocarbons from a diatomite-type formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.W.

1984-12-04

An in-situ process for recovering hydrocarbons from a diatomite-type formation which comprises contacting the diatomite formation with a C/sub 4/-C/sub 10/ alcohol and thereafter displacing the hydrocarbon-alcohol mixture with an aqueous alkaline solution towards a production well. The aqueous alkaline solution can be displaced with additional solution or another suitable medium such as a connate water drive.

Prospects for arbuscular mycorrhizal fungi (AMF) to assist in phytoremediation of soil hydrocarbon contaminants.

PubMed

Rajtor, Monika; Piotrowska-Seget, Zofia

2016-11-01

Arbuscular mycorrhizal fungi (AMF) form mutualistic associations with the roots of 80-90% of vascular plant species and may constitute up to 50% of the total soil microbial biomass. AMF have been considered to be a tool to enhance phytoremediation, as their mycelium create a widespread underground network that acts as a bridge between plant roots, soil and rhizosphere microorganisms. Abundant extramatrical hyphae extend the rhizosphere thus creating the hyphosphere, which significantly increases the area of a plant's access to nutrients and contaminants. The paper presents and evaluates the role and significance of AMF in phytoremediation of hydrocarbon contaminated sites. We focused on (1) an impact of hydrocarbons on arbuscular mycorrhizal symbiosis, (2) a potential of AMF to enhance phytoremediation, (3) determinants that influence effectiveness of hydrocarbon removal from contaminated soils. This knowledge may be useful for selection of proper plant and fungal symbionts and crucial to optimize environmental conditions for effective AMF-mediated phytoremediation. It has been concluded that three-component phytoremediation systems based on synergistic interactions between plant roots, AMF and hydrocarbon-degrading microorganisms demonstrated high effectiveness in dissipation of organic pollutants in soil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Volatile hydrocarbons and fuel oxygenates: Chapter 12

USGS Publications Warehouse

Cozzarelli, Isabelle M.

2014-01-01

Petroleum hydrocarbons and fuel oxygenates are among the most commonly occurring and widely distributed contaminants in the environment. This chapter presents a summary of the sources, transport, fate, and remediation of volatile fuel hydrocarbons and fuel additives in the environment. Much research has focused on the transport and transformation processes of petroleum hydrocarbons and fuel oxygenates, such as benzene, toluene, ethylbenzene, and xylenes and methyl tert‐butyl ether, in groundwater following release from underground storage tanks. Natural attenuation from biodegradation limits the movement of these contaminants and has received considerable attention as an environmental restoration option. This chapter summarizes approaches to environmental restoration, including those that rely on natural attenuation, and also engineered or enhanced remediation. Researchers are increasingly combining several microbial and molecular-based methods to give a complete picture of biodegradation potential and occurrence at contaminated field sites. New insights into the fate of petroleum hydrocarbons and fuel additives have been gained by recent advances in analytical tools and approaches, including stable isotope fractionation, analysis of metabolic intermediates, and direct microbial evidence. However, development of long-term detailed monitoring programs is required to further develop conceptual models of natural attenuation and increase our understanding of the behavior of contaminant mixtures in the subsurface.

Downhole fluid injection systems, CO₂ sequestration methods, and hydrocarbon material recovery methods

DOEpatents

Schaef, Herbert T.; McGrail, B. Peter

2015-07-28

Downhole fluid injection systems are provided that can include a first well extending into a geological formation, and a fluid injector assembly located within the well. The fluid injector assembly can be configured to inject a liquid CO₂/H₂O-emulsion into the surrounding geological formation. CO₂ sequestration methods are provided that can include exposing a geological formation to a liquid CO₂/H₂O-emulsion to sequester at least a portion of the CO₂ from the emulsion within the formation. Hydrocarbon material recovery methods are provided that can include exposing a liquid CO₂/H₂O-emulsion to a geological formation having the hydrocarbon material therein. The methods can include recovering at least a portion of the hydrocarbon material from the formation.

In situ recovery from residually heated sections in a hydrocarbon containing formation

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael; Ryan, Robert Charles

2010-12-14

Methods of treating a tar sands formation is described herein. The methods may include providing heat to a first section of a hydrocarbon layer in the formation from a plurality of heaters located in the first section of the formation. Heat is transferred from the heaters so that at least a first section of the formation reaches a selected temperature. At least a portion of residual heat from the first section transfers from the first section to a second section of the formation. At least a portion of hydrocarbons in the second section are mobilized by providing a solvation fluid and/or a pressurizing fluid to the second section of the formation.

Gum and deposit formation from jet turbine and diesel fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayo, F.R.; Lan, B.Y.

1983-09-01

The present paper describes measurements of rates of oxidation and soluble gum formation in both pure hydrocarbons and in mixed hydrocarbon fuels. Some patterns which appear can be explained on the basis of what is known about co-oxidation of hydrocarbon mixtures. The oxidations were conducted in an oil bath at 130/sup 0/C. Gum formation is closely associated with oxidation. The compounds that copolymerize with oxygen to produce polyperoxides require the least amount of oxygen to yield a mg of gum; among other pure hydrocarbons and fuels, the rates of gum formation and oxygen absorption decrease together. The most useful approachmore » to understanding and reducing gum and deposit formation will come through understanding the effects of condensed aromatic and heterocyclic compounds on the oxidation rates of fuels. 4 figures. 4 tables.« less

Role of methyl group number on SOA formation from monocyclic aromatic hydrocarbons photooxidation under low-NOx conditions

NASA Astrophysics Data System (ADS)

Li, L.; Tang, P.; Nakao, S.; Chen, C.-L.; Cocker, D. R., III

2016-02-01

Substitution of methyl groups onto the aromatic ring determines the secondary organic aerosol (SOA) formation from the monocyclic aromatic hydrocarbon precursor (SOA yield and chemical composition). This study links the number of methyl groups on the aromatic ring to SOA formation from monocyclic aromatic hydrocarbons photooxidation under low-NOx conditions (HC/NO > 10 ppbC : ppb). Monocyclic aromatic hydrocarbons with increasing numbers of methyl groups are systematically studied. SOA formation from pentamethylbenzene and hexamethylbenzene are reported for the first time. A decreasing SOA yield with increasing number of methyl groups is observed. Linear trends are found in both f44 vs. f43 and O / C vs. H / C for SOA from monocyclic aromatic hydrocarbons with zero to six methyl groups. An SOA oxidation state predictive method based on benzene is used to examine the effect of added methyl groups on aromatic oxidation under low-NOx conditions. Further, the impact of methyl group number on density and volatility of SOA from monocyclic aromatic hydrocarbons is explored. Finally, a mechanism for methyl group impact on SOA formation is suggested. Overall, this work suggests that, as more methyl groups are attached on the aromatic ring, SOA products from these monocyclic aromatic hydrocarbons become less oxidized per mass/carbon on the basis of SOA yield or chemical composition.

Laboratory Investigation of Organic Aerosol Formation from Aromatic Hydrocarbons

DOE R&D Accomplishments Database

Molina, Luisa T.; Molina, Mario J.; Zhang, Renyi

2006-08-23

Our work for this DOE funded project includes: (1) measurements of the kinetics and mechanism of the gas-phase oxidation reactions of the aromatic hydrocarbons initiated by OH; (2) measurements of aerosol formation from the aromatic hydrocarbons; and (3) theoretical studies to elucidate the OH-toluene reaction mechanism using quantum-chemical and rate theories.

Shallow gas in Cenozoic sediments of the Southern North Sea

NASA Astrophysics Data System (ADS)

Trampe, Anna F.; Lutz, Rüdiger; Franke, Dieter; Thöle, Hauke; Arfai, Jashar

2013-04-01

Shallow petroleum systems in the southern North Sea are known for several decades but they were not actively explored for a long time. In recent years these unconventional shallow petroleum systems are studied in greater detail and one shallow gas field (A-12) is in production in the Netherlands. Additionally, oil was encountered in Miocene sandstones in the southern Danish North Sea (Lille John well) just north of the Danish-German border. Seismic amplitude anomalies are an indication for hydrocarbons in sediments. Therefore we have mapped the occurrence of seismic amplitude anomalies in the German North Sea based on more than 25.000 km of 2D seismic data and around 4.000 km2 of 3D seismic data. Amplitude anomalies are ubiquitous phenomena in the study area. These anomalies are not only caused by hydrocarbons but also by changing lithologies e.g. peat or fluid migration. Therefore several classes of seismic anomalies, e.g. bright spots, chimneys, blanking areas and velocity pull-down were mapped. Examples for these classes were studied with AVO (amplitude variation with offset) analyses to verify the existence or non-existence of gas in the sediments. Shallow gas can be produced and transported through the dense pipeline grid of the southern and central North Sea or it could be burned offshore close to wind parks in small power plants and the electric energy then transported through the existing power connections of the wind parks. Thus enabling a continuous energy supply during calm wind periods. This study is carried out within the framework of the project "Geoscientific Potential of the German North Sea (GPDN)" in which the Cenozoic sedimentary system was mapped in great detail. A detailed model of delta evolution (Baltic river system) was developed which serves as a structural framework. The studied interval is time equivalent to the Utsira formation which is used offshore Norway for sequestration of CO2. These different possibilities of using or exploiting the underground emphasize the need for detailed knowledge on the underground for sound decisions on the future use of this area.

Solution mining dawsonite from hydrocarbon containing formations with a chelating agent

DOEpatents

Vinegar, Harold J [Bellaire, TX

2009-07-07

A method for treating an oil shale formation comprising dawsonite includes providing heat from one or more heaters to the formation to heat the formation. Hydrocarbon fluids are produced from the formation. At least some dawsonite in the formation is decomposed with the provided heat. A chelating agent is provided to the formation to dissolve at least some dawsonite decomposition products. The dissolved dawsonite decomposition products are produced from the formation.

Formation and emission of large furans and oxygenated hydrocarbons from flames

PubMed Central

Johansson, K. Olof; Dillstrom, Tyler; Monti, Matteo; El Gabaly, Farid; Campbell, Matthew F.; Schrader, Paul E.; Popolan-Vaida, Denisia M.; Richards-Henderson, Nicole K.; Wilson, Kevin R.; Violi, Angela; Michelsen, Hope A.

2016-01-01

Many oxygenated hydrocarbon species formed during combustion, such as furans, are highly toxic and detrimental to human health and the environment. These species may also increase the hygroscopicity of soot and strongly influence the effects of soot on regional and global climate. However, large furans and associated oxygenated species have not previously been observed in flames, and their formation mechanism and interplay with polycyclic aromatic hydrocarbons (PAHs) are poorly understood. We report on a synergistic computational and experimental effort that elucidates the formation of oxygen-embedded compounds, such as furans and other oxygenated hydrocarbons, during the combustion of hydrocarbon fuels. We used ab initio and probabilistic computational techniques to identify low-barrier reaction mechanisms for the formation of large furans and other oxygenated hydrocarbons. We used vacuum-UV photoionization aerosol mass spectrometry and X-ray photoelectron spectroscopy to confirm these predictions. We show that furans are produced in the high-temperature regions of hydrocarbon flames, where they remarkably survive and become the main functional group of oxygenates that incorporate into incipient soot. In controlled flame studies, we discovered ∼100 oxygenated species previously unaccounted for. We found that large alcohols and enols act as precursors to furans, leading to incorporation of oxygen into the carbon skeletons of PAHs. Our results depart dramatically from the crude chemistry of carbon- and oxygen-containing molecules previously considered in hydrocarbon formation and oxidation models and spearhead the emerging understanding of the oxidation chemistry that is critical, for example, to control emissions of toxic and carcinogenic combustion by-products, which also greatly affect global warming. PMID:27410045

Formation and emission of large furans and oxygenated hydrocarbons from flames.

PubMed

Johansson, K Olof; Dillstrom, Tyler; Monti, Matteo; El Gabaly, Farid; Campbell, Matthew F; Schrader, Paul E; Popolan-Vaida, Denisia M; Richards-Henderson, Nicole K; Wilson, Kevin R; Violi, Angela; Michelsen, Hope A

2016-07-26

Many oxygenated hydrocarbon species formed during combustion, such as furans, are highly toxic and detrimental to human health and the environment. These species may also increase the hygroscopicity of soot and strongly influence the effects of soot on regional and global climate. However, large furans and associated oxygenated species have not previously been observed in flames, and their formation mechanism and interplay with polycyclic aromatic hydrocarbons (PAHs) are poorly understood. We report on a synergistic computational and experimental effort that elucidates the formation of oxygen-embedded compounds, such as furans and other oxygenated hydrocarbons, during the combustion of hydrocarbon fuels. We used ab initio and probabilistic computational techniques to identify low-barrier reaction mechanisms for the formation of large furans and other oxygenated hydrocarbons. We used vacuum-UV photoionization aerosol mass spectrometry and X-ray photoelectron spectroscopy to confirm these predictions. We show that furans are produced in the high-temperature regions of hydrocarbon flames, where they remarkably survive and become the main functional group of oxygenates that incorporate into incipient soot. In controlled flame studies, we discovered ∼100 oxygenated species previously unaccounted for. We found that large alcohols and enols act as precursors to furans, leading to incorporation of oxygen into the carbon skeletons of PAHs. Our results depart dramatically from the crude chemistry of carbon- and oxygen-containing molecules previously considered in hydrocarbon formation and oxidation models and spearhead the emerging understanding of the oxidation chemistry that is critical, for example, to control emissions of toxic and carcinogenic combustion by-products, which also greatly affect global warming.

Formation and emission of large furans and oxygenated hydrocarbons from flames

DOE PAGES

Johansson, K. Olof; Dillstrom, Tyler; Monti, Matteo; ...

2016-07-07

Many oxygenated hydrocarbon species formed during combustion, such as furans, are highly toxic and detrimental to human health and the environment. These species may also increase the hygroscopicity of soot and strongly influence the effects of soot on regional and global climate. However, large furans and associated oxygenated species have not previously been observed in flames, and their formation mechanism and interplay with polycyclic aromatic hydrocarbons (PAHs) are poorly understood. We report on a synergistic computational and experimental effort that elucidates the formation of oxygen-embedded compounds, such as furans and other oxygenated hydrocarbons, during the combustion of hydrocarbon fuels. Wemore » used ab initio and probabilistic computational techniques to identify low-barrier reaction mechanisms for the formation of large furans and other oxygenated hydrocarbons. We used vacuum-UV photoionization aerosol mass spectrometry and X-ray photoelectron spectroscopy to confirm these predictions. We show that fura ns are produced in the high- Temperature regions of hydrocarbon flames, where they remarkably survive and become the main functional group of oxygenates that incorporate into incipient soot. In controlled flame studies, we discovered ~100 oxygenated species previously unaccounted for. We found that large alcohols and enols act as precursors to furans, leading to incorporation of oxygen into the carbon skeletons of PAHs. Our results depart dramatically from the crude chemistry of carbonand oxygen-containing molecules previously considered in hydrocarbon formation and oxidation models and spearhead the emerging understanding of the oxidation chemistry that is critical, for example, to control emissions of toxic and carcinogenic combustion by-products, which also greatly affect global warming.« less

In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

DOEpatents

Taylor, Robert T.; Jackson, Kenneth J.; Duba, Alfred G.; Chen, Ching-I

1998-01-01

An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating.

In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

DOEpatents

Taylor, R.T.; Jackson, K.J.; Duba, A.G.; Chen, C.I.

1998-05-19

An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants are described. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating. 21 figs.

Insights into Hydrocarbon Formation by Nitrogenase Cofactor Homologs

PubMed Central

Lee, Chi Chung; Hu, Yilin

2015-01-01

ABSTRACT The L-cluster is an all-iron homolog of nitrogenase cofactors. Driven by europium(II) diethylenetriaminepentaacetate [Eu(II)-DTPA], the isolated L-cluster is capable of ATP-independent reduction of CO and CN− to C1 to C4 and C1 to C6 hydrocarbons, respectively. Compared to its cofactor homologs, the L-cluster generates considerably more CH4 from the reduction of CO and CN−, which could be explained by the presence of a “free” Fe atom that is “unmasked” by homocitrate as an additional site for methanation. Moreover, the elevated CH4 formation is accompanied by a decrease in the amount of longer hydrocarbons and/or the lengths of the hydrocarbon products, illustrating a competition between CH4 formation/release and C−C coupling/chain extension. These observations suggest the possibility of designing simpler synthetic clusters for hydrocarbon formation while establishing the L-cluster as a platform for mechanistic investigations of CO and CN− reduction without complications originating from the heterometal and homocitrate components. PMID:25873377

Hydrocarbon potential assessment of Ngimbang formation, Rihen field of Northeast Java Basin

NASA Astrophysics Data System (ADS)

Pandito, R. H.; Haris, A.; Zainal, R. M.; Riyanto, A.

2017-07-01

The assessment of Ngimbang formation at Rihen field of Northeast Java Basin has been conducted to identify the hydrocarbon potential by analyzing the response of passive seismic on the proven reservoir zone and proposing a tectonic evolution model. In the case of petroleum exploration in Northeast Java basin, the Ngimbang formation cannot be simply overemphasized. East Java Basin has been well known as one of the mature basins producing hydrocarbons in Indonesia. This basin was stratigraphically composed of several formations from the old to the young i.e., the basement, Ngimbang, Kujung, Tuban, Ngerayong, Wonocolo, Kawengan and Lidah formation. All of these formations have proven to become hydrocarbon producer. The Ngrayong formation, which is geologically dominated by channels, has become a production formation. The Kujung formation that has been known with the reef build up has produced more than 102 million barrel of oil. The Ngimbang formation so far has not been comprehensively assessed in term its role as a source rock and a reservoir. In 2013, one exploratory well has been drilled at Ngimbang formation and shown a gas discovery, which is indicated on Drill Stem Test (DST) reading for more than 22 MMSCFD of gas. This discovery opens new prospect in exploring the Ngimbang formation.

Formation of fatty acids in photochemical conversions of saturated hydrocarbons

NASA Technical Reports Server (NTRS)

Telegina, T. A.; Pavlovskaya, T. Y.; Ladyzhenskaya, A. I.

1977-01-01

Abiogenic synthesis of fatty acids was studied in photochemical conversions of saturated hydrocarbons. It was shown that, in a hydrocarbon water CaCO3 suspension, the action of 254 nm UV rays caused the formation of fatty acids with a maximum number of carbon atoms in the chain not exceeding that in the initial hydrocarbon. Synthesis of acetic, propionic, butyric, valeric, caproic, enanthic and caprylic (in the case of octane) acids occurs in heptane water CaCO3 and octane water CaCO3 systems.

Ethanol Conversion to Hydrocarbons on HZSM-5: Effect of Reaction Conditions and Si/Al Ratio on the Product Distributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramasamy, Karthikeyan K.; Wang, Yong

2014-11-17

The Conversion of ethanol to hydrocarbon over HZSM-5 zeolite with different Si/Al ratios was investigated under various reaction conditions. The catalyst with a higher Si/Al ratio (low acid density) deactivated faster and generated more unsaturated compounds at a similar time-on-stream. Temperature affects the catalytic activity with respect to liquid hydrocarbon generation and the hydrocarbon product composition. At lower temperatures (~300°C), the catalyst deactivated faster with respect to the liquid hydrocarbon formation. Higher temperatures (~400°C) reduced the formation of liquid range hydrocarbons and formed more gaseous fractions. Weight hourly space velocity was also found to affect product selectivity with higher weightmore » hourly space velocity leading to a higher extent of ethylene formation. The experimental results were analyzed in terms of the product composition and the coke content with respect to catalyst time-on-stream and compared with the catalyst lifetime with respect to the variables tested on the conversion of ethanol to hydrocarbon.« less

Solution mining and heating by oxidation for treating hydrocarbon containing formations

DOEpatents

Vinegar, Harold J.; Stegemeier, George Leo

2009-06-23

A method for treating an oil shale formation comprising nahcolite includes providing a first fluid to a portion of the formation. A second fluid is produced from the portion. The second fluid includes at least some nahcolite dissolved in the first fluid. A controlled amount of oxidant is provided to the portion of the formation. Hydrocarbon fluids are produced from the formation.

Reservoir characterization of the Smackover Formation in southwest Alabama. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kopaska-Merkel, D.C.; Hall, D.R.; Mann, S.D.

1993-02-01

The Upper Jurassic Smackover Formation is found in an arcuate belt in the subsurface from south Texas to panhandle Florida. The Smackover is the most prolific hydrocarbon-producing formation in Alabama and is an important hydrocarbon reservoir from Florida to Texas. In this report Smackover hydrocarbon reservoirs in southwest Alabama are described. Also, the nine enhanced- and improved-recovery projects that have been undertaken in the Smackover of Alabama are evaluated. The report concludes with recommendations about potential future enhanced- and improved-recovery projects in Smackover reservoirs in Alabama and an estimate of the potential volume of liquid hydrocarbons recoverable by enhanced- andmore » improved-recovery methods from the Smackover of Alabama.« less

Reservoir characterization of the Smackover Formation in southwest Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kopaska-Merkel, D.C.; Hall, D.R.; Mann, S.D.

1993-02-01

The Upper Jurassic Smackover Formation is found in an arcuate belt in the subsurface from south Texas to panhandle Florida. The Smackover is the most prolific hydrocarbon-producing formation in Alabama and is an important hydrocarbon reservoir from Florida to Texas. In this report Smackover hydrocarbon reservoirs in southwest Alabama are described. Also, the nine enhanced- and improved-recovery projects that have been undertaken in the Smackover of Alabama are evaluated. The report concludes with recommendations about potential future enhanced- and improved-recovery projects in Smackover reservoirs in Alabama and an estimate of the potential volume of liquid hydrocarbons recoverable by enhanced- andmore » improved-recovery methods from the Smackover of Alabama.« less

Creating and maintaining a gas cap in tar sands formations

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

2010-03-16

Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

Integrated magnetic, gravity, and GPR surveys to locate the probable source of hydrocarbon contamination in Sharm El-Sheikh area, south Sinai, Egypt

NASA Astrophysics Data System (ADS)

Morsy, Mona; Rashed, Mohamed

2013-01-01

Sharm El-Sheikh waters were suddenly hit by hydrocarbon spills which created a serious threat to the prosperous tourism industry in and around the city. Analysis of soil samples, water samples, and seabed samples collected in and around the contaminated bay area showed anomalous levels of hydrocarbons. An integrated geophysical investigation, using magnetic, gravity, and ground penetrating radar geophysical tools, was conducted in the headland overlooking the contaminated bay in order to delineate the possible subsurface source of contamination. The results of the geophysical investigations revealed three underground manmade reinforced concrete tanks and a complicated network of buried steel pipes in addition to other unidentified buried objects. The depths and dimensions of the discovered objects were determined. Geophysical investigations also revealed the presence of a north-south oblique slip fault running through the eastern part of the studied area. Excavations, conducted later on, confirmed the presence of one of the tanks delineated by the geophysical surveys.

Converting oil shale to liquid fuels: energy inputs and greenhouse gas emissions of the Shell in situ conversion process.

PubMed

Brandt, Adam R

2008-10-01

Oil shale is a sedimentary rock that contains kerogen, a fossil organic material. Kerogen can be heated to produce oil and gas (retorted). This has traditionally been a CO2-intensive process. In this paper, the Shell in situ conversion process (ICP), which is a novel method of retorting oil shale in place, is analyzed. The ICP utilizes electricity to heat the underground shale over a period of 2 years. Hydrocarbons are produced using conventional oil production techniques, leaving shale oil coke within the formation. The energy inputs and outputs from the ICP, as applied to oil shales of the Green River formation, are modeled. Using these energy inputs, the greenhouse gas (GHG) emissions from the ICP are calculated and are compared to emissions from conventional petroleum. Energy outputs (as refined liquid fuel) are 1.2-1.6 times greater than the total primary energy inputs to the process. In the absence of capturing CO2 generated from electricity produced to fuel the process, well-to-pump GHG emissions are in the range of 30.6-37.1 grams of carbon equivalent per megajoule of liquid fuel produced. These full-fuel-cycle emissions are 21%-47% larger than those from conventionally produced petroleum-based fuels.

Hydrocarbon Potential in Sandstone Reservoir Isolated inside Low Permeability Shale Rock (Case Study: Beruk Field, Central Sumatra Basin)

NASA Astrophysics Data System (ADS)

Diria, Shidqi A.; Musu, Junita T.; Hasan, Meutia F.; Permono, Widyo; Anwari, Jakson; Purba, Humbang; Rahmi, Shafa; Sadjati, Ory; Sopandi, Iyep; Ruzi, Fadli

2018-03-01

Upper Red Bed, Menggala Formation, Bangko Formation, Bekasap Formation and Duri Formationare considered as the major reservoirs in Central Sumatra Basin (CSB). However, Telisa Formation which is well-known as seal within CSB also has potential as reservoir rock. Field study discovered that lenses and layers which has low to high permeability sandstone enclosed inside low permeability shale of Telisa Formation. This matter is very distinctive and giving a new perspective and information related to the invention of hydrocarbon potential in reservoir sandstone that isolated inside low permeability shale. This study has been conducted by integrating seismic data, well logs, and petrophysical data throughly. Facies and static model are constructed to estimate hydrocarbon potential resource. Facies model shows that Telisa Formation was deposited in deltaic system while the potential reservoir was deposited in distributary mouth bar sandstone but would be discontinued bedding among shale mud-flat. Besides, well log data shows crossover between RHOB and NPHI, indicated that distributary mouth bar sandstone is potentially saturated by hydrocarbon. Target area has permeability ranging from 0.01-1000 mD, whereas porosity varies from 1-30% and water saturation varies from 30-70%. The hydrocarbon resource calculation approximates 36.723 MSTB.

Induction log responses to layered, dipping, and anisotropic formations: Induction log shoulder-bed corrections to anisotropic formations and the effect of shale anisotropy in thinly laminated sand/shale sequences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hagiwara, Teruhiko

1996-12-31

Induction log responses to layered, dipping, and anisotropic formations are examined analytically. The analytical model is especially helpful in understanding induction log responses to thinly laminated binary formations, such as sand/shale sequences, that exhibit macroscopically anisotropic: resistivity. Two applications of the analytical model are discussed. In one application we examine special induction log shoulder-bed corrections for use when thin anisotropic beds are encountered. It is known that thinly laminated sand/shale sequences act as macroscopically anisotropic: formations. Hydrocarbon-bearing formations also act as macroscopically anisotropic formations when they consist of alternating layers of different grain-size distributions. When such formations are thick, inductionmore » logs accurately read the macroscopic conductivity, from which the hydrocarbon saturation in the formations can be computed. When the laminated formations are not thick, proper shoulder-bed corrections (or thin-bed corrections) should be applied to obtain the true macroscopic formation conductivity and to estimate the hydrocarbon saturation more accurately. The analytical model is used to calculate the thin-bed effect and to evaluate the shoulder-bed corrections. We will show that the formation resistivity and hence the hydrocarbon saturation are greatly overestimated when the anisotropy effect is not accounted for and conventional shoulder-bed corrections are applied to the log responses from such laminated formations.« less

Method for producing viscous hydrocarbons

DOEpatents

Poston, Robert S.

1982-01-01

A method for recovering viscous hydrocarbons and synthetic fuels from a subterranean formation by drilling a well bore through the formation and completing the well by cementing a casing means in the upper part of the pay zone. The well is completed as an open hole completion and a superheated thermal vapor stream comprised of steam and combustion gases is injected into the lower part of the pay zone. The combustion gases migrate to the top of the pay zone and form a gas cap which provides formation pressure to produce the viscous hydrocarbons and synthetic fuels.

DEVELOPMENT OF A METHODOLOGY FOR REGIONAL EVALUATION OF CONFINING BED INTEGRITY

EPA Science Inventory

For safe underground injection of liquid waste, confining formations must be thick, extensive, and have low permeability. Recognition of faults that extend from the potential injection zone to underground sources of drinking water is critical for evaluation of confining-bed integ...

Numerical simulation of phenomenon on zonal disintegration in deep underground mining in case of unsupported roadway

NASA Astrophysics Data System (ADS)

Han, Fengshan; Wu, Xinli; Li, Xia; Zhu, Dekang

2018-02-01

Zonal disintegration phenomenon was found in deep mining roadway surrounding rock. It seriously affects the safety of mining and underground engineering and it may lead to the occurrence of natural disasters. in deep mining roadway surrounding rock, tectonic stress in deep mining roadway rock mass, horizontal stress is much greater than the vertical stress, When the direction of maximum principal stress is parallel to the axis of the roadway in deep mining, this is the main reasons for Zonal disintegration phenomenon. Using ABAQUS software to numerical simulation of the three-dimensional model of roadway rupture formation process systematically, and the study shows that when The Direction of maximum main stress in deep underground mining is along the roadway axial direction, Zonal disintegration phenomenon in deep underground mining is successfully reproduced by our numerical simulation..numerical simulation shows that using ABAQUA simulation can reproduce Zonal disintegration phenomenon and the formation process of damage of surrounding rock can be reproduced. which have important engineering practical significance.

Compositions produced using an in situ heat treatment process

DOEpatents

Roes, Augustinus Wilhelmus Maria; Nair, Vijay; Munsterman, Erwin Hunh; Van Bergen, Petrus Franciscus; Van Den Berg, Franciscus Gondulfus Antonius

2013-05-28

Methods for treating a subsurface formation and compositions produced therefrom are described herein. At least one method for producing hydrocarbons from a subsurface formation includes providing heat to the subsurface formation using an in situ heat treatment process. One or more formation particles may be formed during heating of the subsurface formation. Fluid that includes hydrocarbons and the formation particles may be produced from the subsurface formation. The formation particles in the produced fluid may include cenospheres and have an average particle size of at least 0.5 micrometers.

Compositions produced using an in situ heat treatment process

DOEpatents

Roes, Augustinus Wilhelmus Maria [Houston, TX; Nair, Vijay [Katy, TX; Munsterman, Erwin Henh [Amsterdam, NL; Van Bergen, Petrus Franciscus [Amsterdam, NL; Van Den Berg, Franciscus Gondulfus Antonius

2009-10-20

Systems, methods, and heaters for treating a subsurface formation are described herein. At least one method for producing hydrocarbons from a subsurface formation includes providing heat to the subsurface formation using an in situ heat treatment process. One or more formation particles may be formed during heating of the subsurface formation. Fluid that includes hydrocarbons and the formation particles may be produced from the subsurface formation. The formation particles in the produced fluid may include cenospheres and have an average particle size of at least 0.5 micrometers.

The origin of high hydrocarbon groundwater in shallow Triassic aquifer in Northwest Guizhou, China.

PubMed

Liu, Shan; Qi, Shihua; Luo, Zhaohui; Liu, Fangzhi; Ding, Yang; Huang, Huanfang; Chen, Zhihua; Cheng, Shenggao

2018-02-01

Original high hydrocarbon groundwater represents a kind of groundwater in which hydrocarbon concentration exceeds 0.05 mg/L. The original high hydrocarbon will significantly reduce the environment capacity of hydrocarbon and lead environmental problems. For the past 5 years, we have carried out for a long-term monitoring of groundwater in shallow Triassic aquifer in Northwest Guizhou, China. We found the concentration of petroleum hydrocarbon was always above 0.05 mg/L. The low-level anthropogenic contamination cannot produce high hydrocarbon groundwater in the area. By using hydrocarbon potential, geochemistry and biomarker characteristic in rocks and shallow groundwater, we carried out a comprehensive study in Dalongjing (DLJ) groundwater system to determine the hydrocarbon source. We found a simplex hydrogeology setting, high-level water-rock-hydrocarbon interaction and obviously original hydrocarbon groundwater in DLJ system. The concentration of petroleum hydrocarbon in shallow aquifer was found to increase with the strong water-rock interaction. Higher hydrocarbon potential was found in the upper of Guanling formation (T 2 g 3 ) and upper of Yongningzhen formation (T 1 yn 4 ). Heavily saturated carbon was observed from shallow groundwater, which presented similar distribution to those from rocks, especially from the deeper groundwater. These results indicated that the high concentrations of original hydrocarbon in groundwater could be due to the hydrocarbon release from corrosion and extraction out of strata over time.

Single well surfactant test to evaluate surfactant floods using multi tracer method

DOEpatents

Sheely, Clyde Q.

1979-01-01

Data useful for evaluating the effectiveness of or designing an enhanced recovery process said process involving mobilizing and moving hydrocarbons through a hydrocarbon bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well, comprising (a) determining hydrocarbon saturation in a volume in the formation near a well bore penetrating formation, (b) injecting sufficient mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore, and (c) determining the hydrocarbon saturation in a volume including at least a part of the volume of (b) by an improved single well surfactant method comprising injecting 2 or more slugs of water containing the primary tracer separated by water slugs containing no primary tracer. Alternatively, the plurality of ester tracers can be injected in a single slug said tracers penetrating varying distances into the formation wherein the esters have different partition coefficients and essentially equal reaction times. The single well tracer method employed is disclosed in U.S. Pat. No. 3,623,842. This method designated the single well surfactant test (SWST) is useful for evaluating the effect of surfactant floods, polymer floods, carbon dioxide floods, micellar floods, caustic floods and the like in subterranean formations in much less time and at much reduced cost compared to conventional multiwell pilot tests.

Method for maximizing shale oil recovery from an underground formation

DOEpatents

Sisemore, Clyde J.

1980-01-01

A method for maximizing shale oil recovery from an underground oil shale formation which has previously been processed by in situ retorting such that there is provided in the formation a column of substantially intact oil shale intervening between adjacent spent retorts, which method includes the steps of back filling the spent retorts with an aqueous slurry of spent shale. The slurry is permitted to harden into a cement-like substance which stabilizes the spent retorts. Shale oil is then recovered from the intervening column of intact oil shale by retorting the column in situ, the stabilized spent retorts providing support for the newly developed retorts.

HYDROCARBON SOURCE ROCK EVALUATION OF MIDDLE PROTEROZOIC SOLOR CHURCH FORMATION, NORTH AMERICAN MID-CONTINENT RIFT SYSTEM, RICE COUNTY, MINNESOTA.

USGS Publications Warehouse

Hatch, J.R.; Morey, G.B.

1985-01-01

Hydrocarbon source rock evaluation of the Middle Proterozoic Solor Church Formation (Keweenawan Supergroup) as sampled in the Lonsdale 65-1 well, Rice County, shows that: the rocks are organic matter lean; the organic matter is thermally post-mature, probably near the transition between the wet gas phase of catagenesis and metagenesis; and the rocks have minimal potential for producing additional hydrocarbons. The observed thermal maturity of the organic matter requires significantly greater burial depths, a higher geothermal gradient, or both. It is likely, that thermal maturation of the organic matter in the Solor Church took place relatively early, and that any hydrocarbons generated during this early phase were probably lost prior to deposition of the overlying formation.

Creating fluid injectivity in tar sands formations

DOEpatents

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2012-06-05

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons including mobilized hydrocarbons are produced from the portion.

A unifying picture of gas-phase formation and growth of PAH (Polycyclic Aromatic Hydrocarbons), soot, diamond and graphite

NASA Technical Reports Server (NTRS)

Frenklach, Michael

1990-01-01

A variety of seemingly different carbon formation processes -- polycyclic aromatic hydrocarbons and diamond in the interstellar medium, soot in hydrocarbon flames, graphite and diamond in plasma-assisted-chemical vapor deposition reactors -- may all have closely related underlying chemical reaction mechanisms. Two distinct mechanisms for gas-phase carbon growth are discussed. At high temperatures it proceeds via the formation of carbon clusters. At lower temperatures it follows a polymerization-type kinetic sequence of chemical reactions of acetylene addition to a radical, and reactivation of the resultant species through H-abstraction by a hydrogen atom.

Use of derivatives to assess preservation of hydrocarbon deposits

NASA Astrophysics Data System (ADS)

Koshkin, K. A.; Melkishev, O. A.

2018-05-01

The paper considers the calculation of derivatives along the surface of a modern and paleostructure map of a Tl2-b formation top used to forecast the preservation of oil and gas deposits in traps according to 3D seismic survey via statistical methods. It also suggests a method to evaluate morphological changes of the formation top by calculating the difference between derivatives. The proposed method allows analyzing structural changes of the formation top in time towards primary migration of hydrocarbons. The comprehensive use of calculated indicators allowed ranking the prepared structures in terms of preservation of hydrocarbon deposits.

Methods of producing alkylated hydrocarbons from an in situ heat treatment process liquid

DOEpatents

Roes, Augustinus Wilhelmus Maria [Houston, TX; Mo, Weijian [Sugar Land, TX; Muylle, Michel Serge Marie [Houston, TX; Mandema, Remco Hugo [Houston, TX; Nair, Vijay [Katy, TX

2009-09-01

A method for producing alkylated hydrocarbons is disclosed. Formation fluid is produced from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a first gas stream. The first gas stream includes olefins. The liquid stream is fractionated to produce at least a second gas stream including hydrocarbons having a carbon number of at least 3. The first gas stream and the second gas stream are introduced into an alkylation unit to produce alkylated hydrocarbons. At least a portion of the olefins in the first gas stream enhance alkylation.

Low-maturity Kulthieth Formation coal: A possible source of polycyclic aromatic hydrocarbons in benthic sediment of the northern Gulf of Alaska

USGS Publications Warehouse

Van Kooten, G. K.; Short, J.W.; Kolak, J.J.

2002-01-01

The successful application of forensic geology to contamination studies involving natural systems requires identification of appropriate endmembers and an understanding of the geologic setting and processes affecting the systems. Studies attempting to delineate the background, or natural, source for hydrocarbon contamination in Gulf of Alaska (GOA) benthic sediments have invoked a number of potential sources, including seep oils, source rocks, and coal. Oil seeps have subsequently been questioned as significant sources of hydrocarbons present in benthic sediments of the GOA in part because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Likewise, native coal has been dismissed in part because ratios of labile hydrocarbons to total organic carbon (e.g. PAH:TOC) for Bering River coal field (BRCF) sources are too low - i.e. the coals are over mature - to be consistent with GOA sediments. We present evidence here that native coal may have been prematurely dismissed, because BRCF coals do not adequately represent the geochemical signatures of coals elsewhere in the Kulthieth Formation. Contrary to previous thought, Kulthieth Formation coals east of the BRCF have much higher PAH: TOC ratios, and the patterns of labile hydrocarbons in these low thermal maturity coals suggest a possible genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analyses of low-maturity Kulthieth Formation coal indicate the low maturity coal is a significant source of PAH. Source apportionment models that neglect this source will underestimate the contribution of native coals to the regional background hydrocarbon signature. ?? Published by Elsevier Science Ltd. on behalf of AEHS.

Carbon Dioxide Tucked into Basalt Converts to Rock

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrail, Pete

2016-11-18

Carbon Sequestration or storing carbon dioxide underground may be one approach to reducing atmospheric levels of the greenhouse gas. Storing it in basalt formations creates a chemical reaction in which the CO2 is transformed into a mineral similar to limestone enabling permanent storage underground. A field study by researchers at the Department of Energy’s Pacific Northwest National Laboratory shows that chemical happens quickly. Within two years, CO2 injected underground in Washington state had converted to the carbonate mineral ankerite.

Carbon Dioxide Tucked into Basalt Converts to Rock

ScienceCinema

McGrail, Pete

2018-06-13

Carbon Sequestration or storing carbon dioxide underground may be one approach to reducing atmospheric levels of the greenhouse gas. Storing it in basalt formations creates a chemical reaction in which the CO2 is transformed into a mineral similar to limestone enabling permanent storage underground. A field study by researchers at the Department of Energy’s Pacific Northwest National Laboratory shows that chemical happens quickly. Within two years, CO2 injected underground in Washington state had converted to the carbonate mineral ankerite.

Treating tar sands formations with dolomite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vinegar, Harold J.; Karanikas, John Michael

A method for treating a karsted formation containing heavy hydrocarbons and dolomite includes providing heat to at least part of one or more karsted layers in the formation from one or more heaters located in the karsted layers. A temperature in at least one of the karsted layers is allowed to reach a decomposition temperature of dolomite in the formation. The dolomite is allowed to decompose and at least some hydrocarbons are produced from at least one of the karsted layers of the formation.

Subsurface heaters with low sulfidation rates

DOEpatents

John, Randy Carl; Vinegar, Harold J

2013-12-10

A system for heating a hydrocarbon containing formation includes a heater having an elongated ferromagnetic metal heater section. The heater is located in an opening in a formation. The heater section is configured to heat the hydrocarbon containing formation. The exposed ferromagnetic metal has a sulfidation rate that goes down with increasing temperature of the heater, when the heater is in a selected temperature range.

Grouped exposed metal heaters

DOEpatents

Vinegar, Harold J.; Coit, William George; Griffin, Peter Terry; Hamilton, Paul Taylor; Hsu, Chia-Fu; Mason, Stanley Leroy; Samuel, Allan James; Watkins, Ronnie Wade

2010-11-09

A system for treating a hydrocarbon containing formation is described. The system includes two or more groups of elongated heaters. The group includes two or more heaters placed in two or more openings in the formation. The heaters in the group are electrically coupled below the surface of the formation. The openings include at least partially uncased wellbores in a hydrocarbon layer of the formation. The groups are electrically configured such that current flow through the formation between at least two groups is inhibited. The heaters are configured to provide heat to the formation.

Grouped exposed metal heaters

DOEpatents

Vinegar, Harold J [Bellaire, TX; Coit, William George [Bellaire, TX; Griffin, Peter Terry [Brixham, GB; Hamilton, Paul Taylor [Houston, TX; Hsu, Chia-Fu [Granada Hills, CA; Mason, Stanley Leroy [Allen, TX; Samuel, Allan James [Kular Lumpar, ML; Watkins, Ronnie Wade [Cypress, TX

2012-07-31

A system for treating a hydrocarbon containing formation is described. The system includes two or more groups of elongated heaters. The group includes two or more heaters placed in two or more openings in the formation. The heaters in the group are electrically coupled below the surface of the formation. The openings include at least partially uncased wellbores in a hydrocarbon layer of the formation. The groups are electrically configured such that current flow through the formation between at least two groups is inhibited. The heaters are configured to provide heat to the formation.

In situ oxidation of subsurface formations

DOEpatents

Beer, Gary Lee [Houston, TX; Mo, Weijian [Sugar Land, TX; Li, Busheng [Houston, TX; Shen, Chonghui [Calgary, CA

2011-01-11

Methods and systems for treating a hydrocarbon containing formation described herein include providing heat to a first portion of the formation from a plurality of heaters in the first portion, producing produced through one or more production wells in a second portion of the formation, reducing or turning off heat provided to the first portion after a selected time, providing an oxidizing fluid through one or more of the heater wells in the first portion, providing heat to the first portion and the second portion through oxidation of at least some hydrocarbons in the first portion, and producing fluids through at least one of the production wells in the second portion. The produced fluids may include at least some oxidized hydrocarbons produced in the first portion.

Anomalous dispersion due to hydrocarbons: The secret of reservoir geophysics?

USGS Publications Warehouse

Brown, R.L.

2009-01-01

When P- and S-waves travel through porous sandstone saturated with hydrocarbons, a bit of magic happens to make the velocities of these waves more frequency-dependent (dispersive) than when the formation is saturated with brine. This article explores the utility of the anomalous dispersion in finding more oil and gas, as well as giving a possible explanation about the effect of hydrocarbons upon the capillary forces in the formation. ?? 2009 Society of Exploration Geophysicists.

Abiogenic formation of alkanes in the Earth's crust as a minor source for global hydrocarbon reservoirs.

PubMed

Sherwood Lollar, B; Westgate, T D; Ward, J A; Slater, G F; Lacrampe-Couloume, G

2002-04-04

Natural hydrocarbons are largely formed by the thermal decomposition of organic matter (thermogenesis) or by microbial processes (bacteriogenesis). But the discovery of methane at an East Pacific Rise hydrothermal vent and in other crustal fluids supports the occurrence of an abiogenic source of hydrocarbons. These abiogenic hydrocarbons are generally formed by the reduction of carbon dioxide, a process which is thought to occur during magma cooling and-more commonly-in hydrothermal systems during water-rock interactions, for example involving Fischer-Tropsch reactions and the serpentinization of ultramafic rocks. Suggestions that abiogenic hydrocarbons make a significant contribution to economic hydrocarbon reservoirs have been difficult to resolve, in part owing to uncertainty in the carbon isotopic signatures for abiogenic versus thermogenic hydrocarbons. Here, using carbon and hydrogen isotope analyses of abiogenic methane and higher hydrocarbons in crystalline rocks of the Canadian shield, we show a clear distinction between abiogenic and thermogenic hydrocarbons. The progressive isotopic trends for the series of C1-C4 alkanes indicate that hydrocarbon formation occurs by way of polymerization of methane precursors. Given that these trends are not observed in the isotopic signatures of economic gas reservoirs, we can now rule out the presence of a globally significant abiogenic source of hydrocarbons.

Public Health Impacts of Secondary Particulate Formation from Aromatic Hydrocarbons in Gasoline

EPA Science Inventory

Background: Aromatic hydrocarbons emitted from gasoline‐powered vehicles contribute to the formation of secondary organic aerosol (SOA), which increases the atmospheric mass concentration of fine particles (PM_2.5). Here we estimate the public health burden associated w...

Kaolinite, illite and quartz dissolution in the karstification of Paleozoic sandstones of the Furnas Formation, Paraná Basin, Southern Brazil

NASA Astrophysics Data System (ADS)

Melo, Mário Sérgio de; Guimarães, Gilson Burigo; Chinelatto, Adilson Luiz; Giannini, Paulo César Fonseca; Pontes, Henrique Simão; Chinelatto, Adriana Scoton Antonio; Atencio, Daniel

2015-11-01

Karstification processes in sandstones of the Furnas Formation, Silurian to Devonian of the Paraná Basin, have been described since the mid-twentieth century. However, some geologists still doubt the idea of true karst in sandstones. Studies carried out in the Campos Gerais region, Paraná State, Southern Brazil, aimed at investigating the nature of erosion processes in Furnas Formation and the role of the dissolution in the development of their notorious erosive features and underground cavities. These studies have led to the recognition of dissolution macro to micro features ('furnas', caves, ponds, sinks, ruiniform relief on cliffs and rocky surfaces, grain corrosion, speleothems, mineral reprecipitation and incrustation). The analysis (scanning electron microscopy, energy dispersive spectrometry and x-ray diffractometry) of sandstones and their alterites has indicated significant dissolution of clay cement along with discrete quartz grain dissolution. This mesodiagenetic cement (kaolinite and illite) is dissolved and reprecipitated as clay minerals with poorly developed crystallinity along with other minerals, such as variscite and minerals of the alunite supergroup, suggesting organic participation in the processes of dissolution and incrustation. The mineral reprecipitation usually forms centimetric speleothems, found in cavities and sheltered rocky surfaces. The cement dissolution associated with other factors (fractures, wet weather, strong hydraulic gradient, antiquity of the landforms) leads to the rock arenisation, the underground erosion and the appearance of the karst features. Carbonate rocks in the basement may locally be increasing the karst forms in the overlying Furnas Formation. The recognition of the karst character of the Furnas Formation sandstones has important implications in the management of underground water resources (increasingly exploited in the region), in the use of the unique geological heritage and in the prevention of geo-environmental accidents resulting from underground erosion phenomena.

Carbon deposition model for oxygen-hydrocarbon combustion. Task 6: Data analysis and formulation of an empirical model

NASA Technical Reports Server (NTRS)

Makel, Darby B.; Rosenberg, Sanders D.

1990-01-01

The formation and deposition of carbon (soot) was studied in the Carbon Deposition Model for Oxygen-Hydrocarbon Combustion Program. An empirical, 1-D model for predicting soot formation and deposition in LO2/hydrocarbon gas generators/preburners was derived. The experimental data required to anchor the model were identified and a test program to obtain the data was defined. In support of the model development, cold flow mixing experiments using a high injection density injector were performed. The purpose of this investigation was to advance the state-of-the-art in LO2/hydrocarbon gas generator design by developing a reliable engineering model of gas generator operation. The model was formulated to account for the influences of fluid dynamics, chemical kinetics, and gas generator hardware design on soot formation and deposition.

78 FR 20949 - Proposed Collection; Comment Request; High-Voltage Continuous Mining Machines Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-08

... Collection; Comment Request; High-Voltage Continuous Mining Machines Standards for Underground Coal Mines... Act of 1995. This program helps to assure that requested data can be provided in the desired format... maintains the safe use of high-voltage continuous mining machines in underground coal mines by requiring...

The relationship between environmental parameters of saline and underground karst - patients with different diseases in the course of speleotherapy - anthropogenic effect - keeping intact the underground environment and curative properties.

NASA Astrophysics Data System (ADS)

Simionca, Iu.; Hoteteu, M.; Chonka, Ia.; Slavik, P.; Kubas, J.; Grudnicki, N.

2009-04-01

One of the non-pharmacological therapy in patients with bronchial asthma (AB) and other BPOC is speleotherapy (ST), recognized as a complementary therapy. The curative effect of ST depends on geophysic structure of massive salt or karst, of mine or cave cavities, lack of noxes and toxic gas, also on the lack of the plant and microbial allergen, on the microclimatic parameters, sanitary and other parameters of the underground environment, on the mechanism of curative factors in these specific environments, on the medical particularities and disease specific speleotherapeutic methodology. An essential role they have environmental studies of underground cavities that own speleotherapeutic properties and use in medical and balneoclimatic tourism purposes. Among these studies are: - Air temperature, soil and salt layer; - Atmospheric pressure and the difference from the outside; - Relative humidity of the air underground; - Velocity of air currents; - Concentration of positive and negative air ions; - Particle size and concentration of saline aerosol; - Concentration of microorganisms, including pathogens, conditioning-pathogenic and saprophytic in air, soil saline and salt walls in rooms designed for speleotherapy; - Concentration of allergens; - Concentration of oxygen and carbon dioxide, the presence and concentration of ozone, the gaseous pollutants (NO2, SO2, hydrocarbons and derivatives of ozone); - Radioactivity (type, value), the presence and concentration of radon. Taking into consideration the possibility of anthropogenic effect on the underground salt or karst environment produced by patients with chronic inflammatory diseases, respiratory or skin allergic diseases is needed to assess the underground environmental sanitary parameters in various main locations (the entrance in the underground, the artificial or natural air flow; the sanatory area " - the location where patients or tourists are keeped for a period of 1-3 or more hours, bathroom) and the mechanism for keeping them intact. The data collected indicate the status of the underground salt or karst environment, allows the composition and aplication of the time period and speleotherapeutic procedures for patients with different pathologies in order to obtain speleotherapeutic positive effect or their use to balneoclimatic tourism, and also allow to assess anthropyc pollution and necessary measures for keeping intact of curative properties or their regeneration.

Methods of making transportation fuel

DOEpatents

Roes, Augustinus Wilhelmus Maria [Houston, TX; Mo, Weijian [Sugar Land, TX; Muylle, Michel Serge Marie [Houston, TX; Mandema, Remco Hugo [Houston, TX; Nair, Vijay [Katy, TX

2012-04-10

A method for producing alkylated hydrocarbons is disclosed. Formation fluid is produced from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a first gas stream. The first gas stream includes olefins. The liquid stream is fractionated to produce at least a second gas stream including hydrocarbons having a carbon number of at least 3. The first gas stream and the second gas stream are introduced into an alkylation unit to produce alkylated hydrocarbons. At least a portion of the olefins in the first gas stream enhance alkylation. The alkylated hydrocarbons may be blended with one or more components to produce transportation fuel.

Method and apparatus for production of subsea hydrocarbon formations

DOEpatents

Blandford, Joseph W.

1995-01-01

A system for controlling, separating, processing and exporting well fluids produced from subsea hydrocarbon formations is disclosed. The subsea well tender system includes a surface buoy supporting one or more decks above the water surface for accommodating equipment to process oil, gas and water recovered from the subsea hydrocarbon formation. The surface buoy includes a surface-piercing central flotation column connected to one or more external floatation tanks located below the water surface. The surface buoy is secured to the seabed by one or more tendons which are anchored to a foundation with piles imbedded in the seabed. The system accommodates multiple versions on the surface buoy configuration.

Observation of chemical erosion of carbon based wall materials in the TEXTOR tokamak

NASA Astrophysics Data System (ADS)

Philipps, V.; Pospieszczyk, A.; Erdweg, M.; Schweer, B.; Vietzke, E.; Winter, J.

1996-01-01

Mass spectroscopy and optical spectroscopy have been used to measure the formation of methane, higher hydrocarbons and of CO during the interaction of limiters with the boundary plasma and of special carbon targets with the scrape-off-layer plasma (SOL) of TEXTOR. Mass spectroscopic data are obtained by the Sniffer probe in the SOL under carbon, boronized and siliconized wall conditions. At target temperatures <=100 °C, methane yields range typically between 0.7 and 1.2%. They vary only little with changing plasma conditions. C2-hydrocarbon formation dominates the overall carbon erosion under many conditions. Their yields increase with decreasing plasma temperature. Siliconization of the walls reduces the methane formation only little but suppresses the formation of higher hydrocarbons significantly. CO formation is dominated by the actual oxygen impurity fluxes and ranges between 0.2% up to 1.5% depending on the wall conditioning. Supporting data on hydrocarbon and CO formation are obtained from the outgassing after the discharge. Optical spectroscopy has been used to determine methane formation yields from CH band emission in front of graphite test limiters positioned at the last closed flux surface. The yields are typically in the range between 1.5 and 5% and are generally a factor 2-3 higher compared to those from mass spectroscopy. The CH4 formation is nearly constant between 200 °C up to 700 °C and decreases beyond 800-1000 °C. It decreases with increasing flux density. C2 hydrocarbon emission from the limiters has not been observed by molecular band emission within the range of normal plasma conditions. They show up only for detached plasma conditions.

High energy-density liquid rocket fuel performance

NASA Technical Reports Server (NTRS)

Rapp, Douglas C.

1990-01-01

A fuel performance database of liquid hydrocarbons and aluminum-hydrocarbon fuels was compiled using engine parametrics from the Space Transportation Engine Program as a baseline. Propellant performance parameters are introduced. General hydrocarbon fuel performance trends are discussed with respect to hydrogen-to-carbon ratio and heat of formation. Aluminum-hydrocarbon fuel performance is discussed with respect to aluminum metal loading. Hydrocarbon and aluminum-hydrocarbon fuel performance is presented with respect to fuel density, specific impulse, and propellant density specific impulse.

A study of nonflammable ArCO 2-hydrocarbon gas mixtures for limited streamer tubes

NASA Astrophysics Data System (ADS)

Cartwright, S.; Schneekloth, U.; Alpat, B.; Artemi, C.; Battiston, R.; Bilei, G.; Italiani, M.; Pauluzzi, M.; Servoli, L.; Messner, R.; Wyss, J.; Zdarko, R.; Johnson, J.

1989-04-01

The gas mixtures generally used until now in limited streamer tube detectors (Ar+C 4H 10 or Ar+CO 2+C 5H 12) are very flammable when leaked into air. The safety issues are therefore very relevant for large-volume underground experiments. We have found a set of completely safe (i.e. nonflammable) ternary mixtures of the kind Ar + hydrocarbon + CO 2 containing less than ˜ 5% of Ar and less than ˜ 10% of hydrocarbon. We tested C 4H 10, C 5H 12 and C 6H 14 as quenching agents. The main characteristics of the various mixtures have been measured: singles (untriggered) counting rate versus high voltage and with different dead times, and average charge. The stability of these mixtures is good, and their spurious streamer activity is compared with the standard binary or ternary mixture. We studied in particular the combination Ar(2.5%) + C 4H 10(9.5%) + CO 2(88%). All the data suggest that this or a similar gas mixture can successfully replace standard flammable mixtures both in tracking devices and hadron calorimeters.

POLYCYCLIC AROMATIC HYDROCARBON FORMATION IN OPPOSED FLOW DIFFUSION FLAMES OF ETHANE. (R825412)

EPA Science Inventory

Abstract

The effect of fuel-side carbon density on the levels of polycyclic aromatic hydrocarbon (PAH) formation in atmospheric pressure, opposed flow, ethane diffusion flames has been studied using heated micro-probe sampling and gas chromatography/mass spectrometry (...

FORMATION OF POLYCYCLIC AROMATIC HYDROCARBONS AND THEIR GROWTH TO SOOT -A REVIEW OF CHEMICAL REACTION PATHWAYS. (R824970)

EPA Science Inventory

The generation by combustion processes of airborne species of current health concern such as polycyclic aromatic hydrocarbons (PAH) and soot particles necessitates a detailed understanding of chemical reaction pathways responsible for their formation. The present review discus...

A study of photochemical againg of ambient air using Potential Aerosol Mass (PAM) chamber under the different sources and types of emissions

NASA Astrophysics Data System (ADS)

Lee, T.; Son, J.; Kim, J.; Kim, S.; Sung, K.; Park, G.; Link, M.; Park, T.; Kim, K.; Kang, S.; Ban, J.; Kim, D. S.

2016-12-01

Recent research proposed that Secondary Aerosol (SA) is important class of predicting future climate change scenarios, health effect, and a general air quality. However, there has been lack of studies to investigate SA formation all over the world. This study tried to focus on understanding potential secondary aerosol formation and its local impact by the photochemical aging of inorganic and organic aerosols in the ambient air using the Potential Aerosol Mass (PAM) chamber under the different sources and types of emissions. PAM chamber manufactured by Aerodyne make an oxidizing environment that simulates oxidation processes on timescales of 12-15 hrs in the atmosphere. Chemical compositions of ambient aerosol and aerosol that was aged in the PAM chamber were alternately measured every 2-minutes using the High Resolution-Time of Flight-Aerosol Mass Spectrometer (HR-ToF-AMS). HR-ToF-AMS provides non-refractory aerosol mass concentrations including nitrate, sulfate, hydrocarbon-like and oxygenated organic aerosol in real time. This study includes a residence area of mixture of sources, a forest site of dominant source of biogenic VOCs, an underground parking lot of dominant vehicle emission, and laboratory experiment of vehicle emissions under different fuels and speeds using the chassis dynamometer. As a result, it was revealed that gasoline and LPG vehicle relatively made more potential SA than diesel vehicle.

Model compound study of the pathways for aromatic hydrocarbon formation in soot.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomczyk, N. A.; Hunt, J. E.; Winans, R. E.

2002-04-29

To explore the mechanisms for formation of aromatic hydrocarbons as precursors to soot, a model system using combustion of biphenyl in a fuel rich flame is studied. The soots acquired at three different temperatures are solvent extracted and the extract characterized by both GCMS and high resolution mass spectrometry. A description of the NMR results for the whole soots has been published (1). The production of most products could be rationalized from the coupling of biphenyls and subsequent aromatic species and the addition of acetylenes to existing aromatic molecules. Early work by Badger on pyrolysis of hydrocarbons is used inmore » developing these schemes (2). The reaction schemes to produce larger aromatic hydrocarbons will be discussed. Richter and Howard have discussed in detail potential reaction mechanisms in the formation of aromatics as precursors to soot (3).« less

[Transport and differentiation of polycyclic aromatic hydrocarbons in air from Dashiwei karst Sinkholes in Guangxi, China].

PubMed

Kong, Xiang-Sheng; Qi, Shi-Hua; Sun, Qian; Huang, Bao-Jian

2012-12-01

The typical karst Dashiwei Sinkholes located in Leye County, Guangxi were chosen as the study object. The air samples from the opening of Dashiwei Sinkholes to the underground river profiles were collected by polyurethane foam passive samplers (PUF-PAS), and the meteorological parameters were observed. The 16 PAHs were analyzed using GC-MS. The results showed that the total PAHs concentration in air in Dashiwei Sinkholes ranged from 33.76 ng x d(-1) to 150.86 ng x d(-1), with an average of 80.36 ng x d(-1). The mean concentrations in the cliff, the bottom and the underground river profiles were 67.17, 85.36 and 101.67 ng x d(-1), respectively. The 2-3 rings PAHs (including phenanthrene, anthracene, napnthalene and fluorene) accounted for 87.97% of the total of PAHs. The transport and accumulation processes of PAHs in air in Dashiwei Sinkholes were: the ground to the cliff section to the bottom section and then to the underground river, and the total PAHs concentrations showed an obvious increasing tendency with the decrease in altitude or increase in the length of the underground river. Low molecular weight PAHs compounds (including phenanthrene, anthracene, flourene and fluoranthene) in air went through differentiation at the bottom of the west peak, the bottom of the sinkhole and the underground river. The primary sources of PAHs were pyrogenic sources with atmosphere transport. Ambient temperature was the predominating factor influencing the transport and accumulation of gas phase PAHs in Dashiwei Sinkholes, following by wind speed, wind direction and relative humidity. Relative humidity and the temperature were the predominating factors influencing the differentiation, following by wind speed and wind direction. As a whole, a "cold trapping effect" of POPs was showed obviously in Dashiwei Sinkholes.

Isoprenoid hydrocarbons produced by thermal alteration of Nostoc muscorum and Rhodopseudomonas spheroides

NASA Technical Reports Server (NTRS)

Philp, R. P.; Brown, S.; Calvin, M.

1978-01-01

The potential of algae and photosynthetic bacteria to serve as precursors of kerogen was studied to determine what factors affect the relative rates of formation of precursor hydrocarbons. Cells of Nostoc muscorum and Rhodopseudomonas spheroides were subjected to thermal alteration (by heating samples in glass tubes sealed under nitrogen) for two, four, and twelve weeks. Both unextracted and extracted cells in the absence and presence of montmorillonite were investigated, and the isoprenoid hydrocarbons produced in these experiments were determined. Phytane and five isomeric phytenes were the main hydrocarbons observed; their relative rates of formation in the different experimental conditions are described. No phytadienes, pristane, or pristenes were detected.

Method and apparatus for production of subsea hydrocarbon formations

DOEpatents

Blandford, J.W.

1995-01-17

A system for controlling, separating, processing and exporting well fluids produced from subsea hydrocarbon formations is disclosed. The subsea well tender system includes a surface buoy supporting one or more decks above the water surface for accommodating equipment to process oil, gas and water recovered from the subsea hydrocarbon formation. The surface buoy includes a surface-piercing central flotation column connected to one or more external flotation tanks located below the water surface. The surface buoy is secured to the sea bed by one or more tendons which are anchored to a foundation with piles imbedded in the sea bed. The system accommodates multiple versions on the surface buoy configuration. 20 figures.

Tectonothermal modeling of hydrocarbon maturation, Central Maracaibo Basin, Venezuela

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manske, M.C.

1996-08-01

The petroliferous Maracaibo Basin of northwestern Venezuela and extreme eastern Colombia has evolved through a complex geologic history. Deciphering the tectonic and thermal evolution is essential in the prediction of hydrocarbon maturation (timing) within the basin. Individual wells in two areas of the central basin, Blocks III and V, have been modeled to predict timing of hydrocarbon generation within the source Upper Cretaceous La Luna Formation, as well as within interbedded shales of the Lower-Middle Eocene Misoa Formation reservoir sandstones. Tectonic evolution, including burial and uplift (erosional) history, has been constrained with available well data. The initial extensional thermal regimemore » of the basin has been approximated with a Mackenzie-type thermal model, and the following compressional stage of basin development by applying a foreland basin model. Corrected Bottom Hole Temperature (BHT) measurements; from wells in the central basin, along with thermal conductivity measurements of rock samples from the entire sedimentary sequence, resulted in the estimation of present day heat flow. An understanding of the basin`s heat flow, then, allowed extrapolation of geothermal gradients through time. The relation of geothermal gradients and overpressure within the Upper Cretaceous hydrocarbon-generating La Luna Formation and thick Colon Formation shales was also taken into account. Maturation modeling by both the conventional Time-Temperature Index (TTI) and kinetic Transformation Ratio (TR) methods predicts the timing of hydrocarbon maturation in the potential source units of these two wells. These modeling results are constrained by vitrinite reflectance and illite/smectite clay dehydration data, and show general agreement. These results also have importance regarding the timing of structural formation and hydrocarbon migration into Misoa reservoirs.« less

Detailed north-south cross section showing environments of deposition, organic richness, and thermal maturities of lower Tertiary rocks in the Uinta Basin, Utah

USGS Publications Warehouse

Johnson, Ronald C.

2014-01-01

The Uinta Basin of northeast Utah has produced large amounts of hydrocarbons from lower Tertiary strata since the 1960s. Recent advances in drilling technologies, in particular the development of efficient methods to drill and hydraulically fracture horizontal wells, has spurred renewed interest in producing hydrocarbons from unconventional low-permeability dolomite and shale reservoirs in the lacustrine, Eocene Green River Formation. The Eocene Green River Formation was deposited in Lake Uinta, a long-lived saline lake that occupied the Uinta Basin, the Piceance Basin to the east, and the intervening Douglas Creek arch. The focus of recent drilling activity has been the informal Uteland Butte member of the Green River Formation and to a much lesser extent the overlying R-0 oil shale zone of the Green River Formation. Initial production rates ranging from 500 to 1,500 barrels of oil equivalent per day have been reported from the Uteland Butte member from horizontal well logs that are as long as 4,000 feet (ft);. The cross section presented here extends northward from outcrop on the southern margin of the basin into the basin’s deep trough, located just south of the Uinta Mountains, and transects the area where this unconventional oil play is developing. The Monument Butte field, which is one of the fields located along this line of section, has produced hydrocarbons from conventional sandstone reservoirs in the lower part of the Green River Formation and underlying Wasatch Formation since 1981. A major fluvial-deltaic system entered Lake Uinta from the south, and this new line of section is ideal for studying the effect of the sediments delivered by this drainage on hydrocarbon reservoirs in the Green River Formation. The cross section also transects the Greater Altamont-Bluebell field in the deepest part of the basin, where hydrocarbons have been produced from fractured, highly overpressured marginal lacustrine and fluvial reservoirs in the Green River, Wasatch, and North Horn Formations since 1970. Datum for the cross section is sea level so that hydrocarbon source rocks and reservoir rocks could be integrated into the structural framework of the basin.

Noble gas and hydrocarbon tracers in multiphase unconventional hydrocarbon systems: Toward integrated advanced reservoir simulators

NASA Astrophysics Data System (ADS)

Darrah, T.; Moortgat, J.; Poreda, R. J.; Muehlenbachs, K.; Whyte, C. J.

2015-12-01

Although hydrocarbon production from unconventional energy resources has increased dramatically in the last decade, total unconventional oil and gas recovery from black shales is still less than 25% and 9% of the totals in place, respectively. Further, the majority of increased hydrocarbon production results from increasing the lengths of laterals, the number of hydraulic fracturing stages, and the volume of consumptive water usage. These strategies all reduce the economic efficiency of hydrocarbon extraction. The poor recovery statistics result from an insufficient understanding of some of the key physical processes in complex, organic-rich, low porosity formations (e.g., phase behavior, fluid-rock interactions, and flow mechanisms at nano-scale confinement and the role of natural fractures and faults as conduits for flow). Noble gases and other hydrocarbon tracers are capably of recording subsurface fluid-rock interactions on a variety of geological scales (micro-, meso-, to macro-scale) and provide analogs for the movement of hydrocarbons in the subsurface. As such geochemical data enrich the input for the numerical modeling of multi-phase (e.g., oil, gas, and brine) fluid flow in highly heterogeneous, low permeability formations Herein we will present a combination of noble gas (He, Ne, Ar, Kr, and Xe abundances and isotope ratios) and molecular and isotopic hydrocarbon data from a geographically and geologically diverse set of unconventional hydrocarbon reservoirs in North America. Specifically, we will include data from the Marcellus, Utica, Barnett, Eagle Ford, formations and the Illinois basin. Our presentation will include geochemical and geological interpretation and our perspective on the first steps toward building an advanced reservoir simulator for tracer transport in multicomponent multiphase compositional flow (presented separately, in Moortgat et al., 2015).

New insight on petroleum system modeling of Ghadames basin, Libya

NASA Astrophysics Data System (ADS)

Bora, Deepender; Dubey, Siddharth

2015-12-01

Underdown and Redfern (2008) performed a detailed petroleum system modeling of the Ghadames basin along an E-W section. However, hydrocarbon generation, migration and accumulation changes significantly across the basin due to complex geological history. Therefore, a single section can't be considered representative for the whole basin. This study aims at bridging this gap by performing petroleum system modeling along a N-S section and provides new insights on source rock maturation, generation and migration of the hydrocarbons using 2D basin modeling. This study in conjunction with earlier work provides a 3D context of petroleum system modeling in the Ghadames basin. Hydrocarbon generation from the lower Silurian Tanezzuft formation and the Upper Devonian Aouinet Ouenine started during the late Carboniferous. However, high subsidence rate during middle to late Cretaceous and elevated heat flow in Cenozoic had maximum impact on source rock transformation and hydrocarbon generation whereas large-scale uplift and erosion during Alpine orogeny has significant impact on migration and accumulation. Visible migration observed along faults, which reactivated during Austrian unconformity. Peak hydrocarbon expulsion reached during Oligocene for both the Tanezzuft and the Aouinet Ouenine source rocks. Based on modeling results, capillary entry pressure driven downward expulsion of hydrocarbons from the lower Silurian Tanezzuft formation to the underlying Bir Tlacsin formation observed during middle Cretaceous. Kinetic modeling has helped to model hydrocarbon composition and distribution of generated hydrocarbons from both the source rocks. Application of source to reservoir tracking technology suggest some accumulations at shallow stratigraphic level has received hydrocarbons from both the Tanezzuft and Aouinet Ouenine source rocks, implying charge mixing. Five petroleum systems identified based on source to reservoir correlation technology in Petromod*. This Study builds upon the original work of Underdown and Redfern, 2008 and offers new insights and interpretation of the data.

THE EFFECTS OF EQUIVALENCE RATIO ON THE FORMATION OF POLYCYCLIC AROMATIC HYDROCARBONS AND SOOT IN PREMIXED ETHANE FLAMES. (R825412)

EPA Science Inventory

Abstract

The formation of polycyclic aromatic hydrocarbons (PAH) and soot has been investigated in atmospheric-pressure, laminar, ethane/oxygen/argon premixed flames as a function of mixture equivalence ratio. Mole fraction profiles of major products, trace aromatics, ...

AROMATIC AND POLYCYCLIC AROMATIC HYDROCARBON FORMATION IN A LAMINAR PREMIXED N-BUTANE FLAME. (R825412)

EPA Science Inventory

Abstract

Experimental and detailed chemical kinetic modeling work has been performed to investigate aromatic and polycyclic aromatic hydrocarbon (PAH) formation pathways in a premixed, rich, sooting, n-butane_¯oxygen_¯argon burner s...

Chemical kinetic models for combustion of hydrocarbons and formation of nitric oxide

NASA Technical Reports Server (NTRS)

Jachimowski, C. J.; Wilson, C. H.

1980-01-01

The formation of nitrogen oxides NOx during combustion of methane, propane, and a jet fuel, JP-4, was investigated in a jet stirred combustor. The results of the experiments were interpreted using reaction models in which the nitric oxide (NO) forming reactions were coupled to the appropriate hydrocarbon combustion reaction mechanisms. Comparison between the experimental data and the model predictions reveals that the CH + N2 reaction process has a significant effect on NO formation especially in stoichiometric and fuel rich mixtures. Reaction models were assembled that predicted nitric oxide levels that were in reasonable agreement with the jet stirred combustor data and with data obtained from a high pressure (5.9 atm (0.6 MPa)), prevaporized, premixed, flame tube type combustor. The results also suggested that the behavior of hydrocarbon mixtures, like JP-4, may not be significantly different from that of pure hydrocarbons. Application of the propane combustion and nitric oxide formation model to the analysis of NOx emission data reported for various aircraft gas turbines showed the contribution of the various nitric oxide forming processes to the total NOx formed.

Geologic framework of oil and gas genesis in main sedimentary basins from Romania Oprea Dicea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ionescu, N.; Morariu, C.D.

1991-03-01

Oil and gas fields located in Moldavic nappes are encompassed in Oligocene and lower Miocene formations, mostly in the marginal folds nappe, where Kliwa Sandstone sequences have high porosity, and in the Black Sea Plateau. The origin of the hydrocarbon accumulations from the Carpathian foredeep seems to be connected to the Oligocene-lower Miocene bituminous formations of the marginal folds and sub-Carpathian nappes. In the Gethic depression, the hydrocarbon accumulations originate in Oligocene and Miocene source rocks and host in structural, stratigraphical, and lithological traps. The accumulations connected with tectonic lines that outline the areal extension of the Oligocene, Miocene, andmore » Pliocene formations are in the underthrusted Moesian platform. The hydrocarbon accumulations related to the Carpathian foreland represent about 40% of all known accumulations in Romania. Most of them are located in the Moesian platform. In this unit, the oil and gas fields present a vertical distribution at different stratigraphic levels, from paleozoic to Neogene, and in all types of reservoirs, suggesting multicycles of oleogenesis, migration, accumulation, and sealing conditions. The hydrocarbon deposits known so far on the Black Sea continental plateau are confined in the Albian, Cenomanian, Turonian-Senonian, and Eocene formations. The traps are of complex type structural, lithologic, and stratigraphic. The reservoirs are sandstones, calcareous sandstones, limestones, and sands. The hydrocarbon source rocks are pelitic and siltic Oligocene formations. Other older source rocks are probably Cretaceous.« less

Contribution of first- versus second-generation products to secondary organic aerosols formed in the oxidation of biogenic hydrocarbons.

PubMed

Ng, Nga L; Kroll, Jesse H; Keywood, Melita D; Bahreini, Roya; Varutbangkul, Varuntida; Flagan, Richard C; Seinfeld, John H; Lee, Anita; Goldstein, Allen H

2006-04-01

Biogenic hydrocarbons emitted by vegetation are important contributors to secondary organic aerosol (SOA), but the aerosol formation mechanisms are incompletely understood. In this study, the formation of aerosols and gas-phase products from the ozonolysis and photooxidation of a series of biogenic hydrocarbons (isoprene, 8 monoterpenes, 4 sesquiterpenes, and 3 oxygenated terpenes) are examined. By comparing aerosol growth (measured by Differential Mobility Analyzers, DMAs) and gas-phase concentrations (monitored by a Proton Transfer Reaction Mass Spectrometer, PTR-MS), we study the general mechanisms of SOA formation. Aerosol growth data are presented in terms of a "growth curve", a plot of aerosol mass formed versus the amount of hydrocarbon reacted. From the shapes of the growth curves, it is found that all the hydrocarbons studied can be classified into two groups based entirely on the number of double bonds of the hydrocarbon, regardless of the reaction systems (ozonolysis or photooxidation) and the types of hydrocarbons studied: compounds with only one double bond and compounds with more than one double bond. For compounds with only one double bond, the first oxidation step is rate-limiting, and aerosols are formed mainly from low volatility first-generation oxidation products; whereas for compounds with more than one double bond, the second oxidation step may also be rate-limiting and second-generation products contribute substantially to SOA growth. This behavior is characterized by a vertical section in the growth curve, in which continued aerosol growth is observed even after all the parent hydrocarbon is consumed.

Methanogenic degradation of petroleum hydrocarbons in subsurface environments remediation, heavy oil formation, and energy recovery.

PubMed

Gray, N D; Sherry, A; Hubert, C; Dolfing, J; Head, I M

2010-01-01

Hydrocarbons are common constituents of surface, shallow, and deep-subsurface environments. Under anaerobic conditions, hydrocarbons can be degraded to methane by methanogenic microbial consortia. This degradation process is widespread in the geosphere. In comparison with other anaerobic processes, methanogenic hydrocarbon degradation is more sustainable over geological time scales because replenishment of an exogenous electron acceptor is not required. As a consequence, this process has been responsible for the formation of the world's vast deposits of heavy oil, which far exceed conventional oil assets such as those found in the Middle East. Methanogenic degradation is also a potentially important component of attenuation in hydrocarbon contamination plumes. Studies of the organisms, syntrophic partnerships, mechanisms, and geochemical signatures associated with methanogenic hydrocarbon degradation have identified common themes and diagnostic markers for this process in the subsurface. These studies have also identified the potential to engineer methanogenic processes to enhance the recovery of energy assets as biogenic methane from residual oils stranded in petroleum systems. Copyright 2010 Elsevier Inc. All rights reserved.

Carbon, oxygen and strontium isotopic constraints on fluid sources, temperatures and biogeochemical processes during the formation of seep carbonates - Secchia River site, Northern Apennines

NASA Astrophysics Data System (ADS)

Viola, Irene; Capozzi, Rossella; Bernasconi, Stefano M.; Rickli, Jörg

2017-07-01

Understanding authigenic seep carbonate formation provides clues for hydrocarbon exploration and insights into contributions to gas budgets of marine environments and the atmosphere. Seep carbonates discovered in the outcropping succession along the Secchia riverbanks (near Modena, Italy) belong to the Argille Azzurre Formation of Early Pleistocene age deposited in an upper shelf environment overlying the Miocene foredeep successions, which include hydrocarbon fields. The fluid migration from the hydrocarbon fields, up to the surface, is presently active on land and started in the marine succession during the Late Miocene. Authigenic globular carbonate concretions and carbonate chimneys are interspersed along the strata throughout the section. A comprehensive geochemical characterisation of the carbonates has been carried out to understand the processes leading to their formation. The carbonate concretions are the record of past hydrocarbon vents linked to the Miocene petroleum system of the Northern Apennines. The samples are composed of > 50% microcrystalline dolomite. The δ13C signatures identify two groups in the samples according to different type of formation processes. Globular concretions have positive values that suggest an influence of CO2 associated to secondary methanogenesis due to microbial degradation of higher hydrocarbons. The analysed chimney, with negative δ13C values, is interpreted as former conduit where carbonate precipitation is promoted by Anaerobic Oxidation of Methane coupled with Sulfate Reduction. The δ18O range, coupled with 87/86Sr signatures, indicate that the contribution of deep connate water from the Miocene reservoirs is up to 23% during the formation of the globular concretions. The connate water occurrence is also documented by higher ambient temperatures. The different isotope signatures in seep carbonates result from the relative contribution of the recognised gas and water components, linked to different plumbing systems and fluid supply from a well-defined hydrocarbon field. The seep carbonate characteristics have enlightened variations in biogeochemical processes, which can be rarely quantified in ancient and present-day marine environments.

Assessing soil and groundwater contamination in a metropolitan redevelopment project.

PubMed

Yun, Junki; Lee, Ju Young; Khim, Jeehyeong; Ji, Won Hyun

2013-08-01

The purpose of this study was to assess contaminated soil and groundwater for the urban redevelopment of a rapid transit railway and a new mega-shopping area. Contaminated soil and groundwater may interfere with the progress of this project, and residents and shoppers may be exposed to human health risks. The study area has been remediated after application of first remediation technologies. Of the entire area, several sites were still contaminated by waste materials and petroleum. For zinc (Zn) contamination, high Zn concentrations were detected because waste materials were disposed in the entire area. For petroleum contamination, high total petroleum hydrocarbon (TPH) and hydrocarbon degrading microbe concentrations were observed at the depth of 7 m because the underground petroleum storage tank had previously been located at this site. Correlation results suggest that TPH (soil) concentration is still related with TPH (groundwater) concentration. The relationship is taken into account in the Spearman coefficient (α).

Point-to-point connectivity prediction in porous media using percolation theory

NASA Astrophysics Data System (ADS)

Tavagh-Mohammadi, Behnam; Masihi, Mohsen; Ganjeh-Ghazvini, Mostafa

2016-10-01

The connectivity between two points in porous media is important for evaluating hydrocarbon recovery in underground reservoirs or toxic migration in waste disposal. For example, the connectivity between a producer and an injector in a hydrocarbon reservoir impact the fluid dispersion throughout the system. The conventional approach, flow simulation, is computationally very expensive and time consuming. Alternative method employs percolation theory. Classical percolation approach investigates the connectivity between two lines (representing the wells) in 2D cross sectional models whereas we look for the connectivity between two points (representing the wells) in 2D aerial models. In this study, site percolation is used to determine the fraction of permeable regions connected between two cells at various occupancy probabilities and system sizes. The master curves of mean connectivity and its uncertainty are then generated by finite size scaling. The results help to predict well-to-well connectivity without need to any further simulation.

Hydrocarbon potential evaluation of the source rocks from the Abu Gabra Formation in the Sufyan Sag, Muglad Basin, Sudan

NASA Astrophysics Data System (ADS)

Qiao, Jinqi; Liu, Luofu; An, Fuli; Xiao, Fei; Wang, Ying; Wu, Kangjun; Zhao, Yuanyuan

2016-06-01

The Sufyan Sag is one of the low-exploration areas in the Muglad Basin (Sudan), and hydrocarbon potential evaluation of source rocks is the basis for its further exploration. The Abu Gabra Formation consisting of three members (AG3, AG2 and AG1 from bottom to top) was thought to be the main source rock formation, but detailed studies on its petroleum geology and geochemical characteristics are still insufficient. Through systematic analysis on distribution, organic matter abundance, organic matter type, organic matter maturity and characteristics of hydrocarbon generation and expulsion of the source rocks from the Abu Gabra Formation, the main source rock members were determined and the petroleum resource extent was estimated in the study area. The results show that dark mudstones are the thickest in the AG2 member while the thinnest in the AG1 member, and the thickness of the AG3 dark mudstone is not small either. The AG3 member have developed good-excellent source rock mainly with Type I kerogen. In the Southern Sub-sag, the AG3 source rock began to generate hydrocarbons in the middle period of Bentiu. In the early period of Darfur, it reached the hydrocarbon generation and expulsion peak. It is in late mature stage currently. The AG2 member developed good-excellent source rock mainly with Types II1 and I kerogen, and has lower organic matter abundance than the AG3 member. In the Southern Sub-sag, the AG2 source rock began to generate hydrocarbons in the late period of Bentiu. In the late period of Darfur, it reached the peak of hydrocarbon generation and its expulsion. It is in middle mature stage currently. The AG1 member developed fair-good source rock mainly with Types II and III kerogen. Throughout the geological evolution history, the AG1 source rock has no effective hydrocarbon generation or expulsion processes. Combined with basin modeling results, we have concluded that the AG3 and AG2 members are the main source rock layers and the Southern Sub-sag is the main source kitchen in the study area. The AG3 and AG2 source rocks have supplied 58.1% and 41.9% of the total hydrocarbon generation, respectively, and 54.9% and 45.1% of the total hydrocarbon expulsion, respectively. Their hydrocarbon expulsion efficiency ratios are 71.0% and 62.3%, respectively. The Southern Sub-sag has supplied more than 90% of the total amounts of hydrocarbon generation and its expulsion.

Coke formation in the thermal cracking of hydrocarbons. 4: Modeling of coke formation in naphtha cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reyniers, G.C.; Froment, G.F.; Kopinke, F.D.

1994-11-01

An extensive experimental program has been carried out in a pilot unit for the thermal cracking of hydrocarbons. On the basis of the experimental information and the insight in the mechanisms for coke formation in pyrolysis reactors, a mathematical model describing the coke formation has been derived. This model has been incorporated in the existing simulation tools at the Laboratorium voor Petrochemische Techniek, and the run length of an industrial naphtha cracking furnace has been accurately simulated. In this way the coking model has been validated.

An assessment of subsurface contamination of an urban coastal aquifer due to oil spill.

PubMed

Nambi, Indumathi M; Rajasekhar, Bokam; Loganathan, Vijay; RaviKrishna, R

2017-04-01

Incidences of leakages of chemicals from underground oil storage tanks or oil-carrying pipelines have posed huge threat to the coastal aquifers around the world. One such leak was recently identified and notified by the people of Tondiarpet, Chennai, India. The assessment of the contamination level was done by obtaining electrical resistivity maps of the subsurface, drilling of 20 new borewells for soil and water analysis, and testing the water quality of 30 existing borewells. Samples were collected from the borewells, and observations were made that included parameters such as odor, moisture, contamination characteristics, lithology, groundwater level, thickness of the free product that are used to demarcate the extent of soil, and water contamination. Furthermore, a multigas detector was used to detect hydrocarbon presence as soil vapor. Moreover, to capture the transport of dissolved hydrocarbons, 10 samples were collected in the periphery of the study area and were analyzed for the presence of petroleum hydrocarbon and polyaromatic hydrocarbon. Analysis of the data indicated the presence of free-phase hydrocarbon in soil and groundwater close to the junction of Thiruvottiyur high (TH) road (TH) and Varadaja Perumal Koil (VPK) street. Although the contaminant plume is confined to a limited area, it has spread more to the southern and eastern side of the pipeline possibly due to continuous abstraction of groundwater by residential apartments. After cutting a trench along the VPK street and plotting of the plume delineation map, observations indicated that the source of the hydrocarbon leak is present in VPK street close to TH road. A multipronged strategy was suggested targeting the remediation of oil in various phases.

Seeking new potential in the early-late Permian Gharif Play, West Central Oman

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guit, F.; Al-Lawati, M.; Nederlof, P.

1995-08-01

West Central Oman is a relatively underexplored area where the hydrocarbons found to date occur mainly within the Early-Late Permian Gharif Formation. Structural definition of the low relief closures is hampered by seismic velocity variations caused by dune terrain. Recent exploration activity resulted in several Gharif discoveries, but highlighted reservoir distribution problems. The Gharif Formation, which consists of fluvio-marine sediments, conformably overlies the glacio-lacustine sediments of the Early Permian Al Khlata Formation. It is overlain by shallow marine carbonates of the Late Permian Khuff Formation, the main regional seal. The area is located distally from the main sediment sources tomore » the east. Reservoir development and lateral continuity are seen as the main risk. Most reservoirs are beyond seismic resolution, only the stacked sandstones of the incised valley fills could provide sufficient acoustic contrast to be recognized on seismic. Geochemical typing indicates that the hydrocarbons in the Gharif can be grouped in two main families: the Huqf and Q-hydrocarbons, which are believed to originate from Cambrian to Precambrian source rocks. Although the two hydrocarbon families are sometimes found in one well, they have very different spatial distributions. The Q-oils form continuous strings of accumulations below the main regional seal, whereas the Huqf hydrocarbons occur scattered throughout the area. Mixed accumulations are found where cross-faults or salt domes intercept a Q-oil fairway. Future exploration activities will be guided by refined sedimentological, stratigraphical and hydrocarbon migration models and by the continued efforts to recognize incised valley fills on seismic.« less

Soot Formation in Hydrocarbon/Air Laminar Jet Diffusion Flames

NASA Technical Reports Server (NTRS)

Sunderland, P. B.; Faeth, G. M.

1994-01-01

Soot processes within hydrocarbon/air diffusion flames are important because they affect the durability and performance of propulsion systems, the hazards of unwanted fires, the pollutant and particulate emissions from combustion processes, and the potential for developing computational combustion. Motivated by these observations, this investigation involved an experimental study of the structure and soot properties of round laminar jet diffusion flames, seeking an improved understanding of soot formation (growth and nucleation) within diffusion flames. The present study extends earlier work in this laboratory concerning laminar smoke points (l) and soot formation in acetylene/air laminar jet diffusion flames (2), emphasizing soot formation in hydrocarbon/air laminar jet diffusion flames for fuels other than acetylene. In the flame system, acetylene is the dominant gas species in the soot formation region and both nucleation and growth were successfully attributed to first-order reactions of acetylene, with nucleation exhibiting an activation energy of 32 kcal/gmol while growth involved negligible activation energy and a collision efficiency of O.53%. In addition, soot growth in the acetylene diffusion flames was comparable to new soot in premixed flame (which also has been attributed to first-order acetylene reactions). In view of this status, a major issue is the nature of soot formation processes in diffusion flame involving hydrocarbon fuels other than acetylene. In particular, information is needed about th dominant gas species in the soot formation region and the impact of gas species other than acetylene on soot nucleation and growth.

Duration of the hydrocarbon fluid formation under thermobaric conditions of the Earth's upper mantle

NASA Astrophysics Data System (ADS)

Mukhina, Elena; Kolesnikov, Anton; Kutcherov, Vladimir

2016-04-01

Deep abiogenic formation of hydrocarbons is an inherent part of the Earth's global carbon cycle. It was experimentally confirmed that natural gas could be formed from inorganic carbon and hydrogen containing minerals at pressure and temperature corresponding to the Earth's upper mantle conditions. Reaction between calcite, wustite and water in the large volume device was studied in several works. It was previously proposed that reaction is possible only after 40 minutes of exposure at high pressure and temperature. In this work similar experiment at P = 60 kbar and T = 1200 K were carried out in "Toroid" type chamber with the 5 seconds duration of thermobaric exposure. Gas chromatographic analysis of the reaction products has shown the presence of hydrocarbon mixture comparable to 5 minutes and 6 hours exposure experiments. Based on this fact it is possible to conclude that the reaction of natural gas formation is instant at least at given thermobaric conditions. This experiment will help to better understand the process of deep hydrocarbon generation, particularly its kinetics.

Technogenic effect of liquidation of coal mines on earth’s entrails: hydrogeochemical aspect

NASA Astrophysics Data System (ADS)

Tarasenko, I. A.; Zinkov, A. V.; Chudaev, O. V.; Vetoshkina, A. V.; Holodilov, I. I.

2017-10-01

The authors of the paper have established the geochemical features of the composition of underground waters and regularities of their formation in the areas of the liquidated coal mines of Russia and Ukraine. It is shown that the mine flood resulted in the formation of technogenic waters which geochemical specificity originates in the feeding field and is transformed in the direction of the filtration flow. It depends on the geological structure of sedimentary basins and the presence in the coal and supra-coal beds of the marine, salt-bearing and freshwater groups of geological formations. The water types are distinguished characterizing the conditions and processes of their formation that may be the regional markers in the hydrochemical and geological constructions. The technogenic waters influenced the safety of the underground waters, sources of water supply of the regions, and surface water channels. The pollutions are of local character in space.

Upper Cretaceous bituminous coal deposits of the Olmos Formation, Maverick County, Texas

USGS Publications Warehouse

Hook, Robert W.; Warwick, Peter D.; SanFilipo, John R.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

2011-01-01

This report describes the bituminous coal deposits of the Olmos Formation (Navarro Group, Upper Cretaceous; Figures 1, 2) of Maverick County in south Texas. Although these were not evaluated quantitatively as part of the current Gulf Coastal Plain coal-resource assessment, a detailed review is presented in this chapter.Prior to the late 1920s, these coal beds were mined underground on a large scale in the vicinity of Eagle Pass, Texas (Figure 1). Since the 1970s, Olmos Formation coals have been mined extensively in both underground and surface mines in nearby Coahuila, Mexico, to supply mine-mouth fuel for power generation at a plant nearby. A tract northeast of Eagle Pass was permitted in the late 1990s for surface mining. In east-central Maverick County, a coalbed methane field is being developed in coal beds of the lower part of the Olmos Formation (Barker et al., 2002; Scott, 2003).

Kinetic modeling of secondary organic aerosol formation: effects of particle- and gas-phase reactions of semivolatile products

NASA Astrophysics Data System (ADS)

Chan, A. W. H.; Kroll, J. H.; Ng, N. L.; Seinfeld, J. H.

2007-08-01

The distinguishing mechanism of formation of secondary organic aerosol (SOA) is the partitioning of semivolatile hydrocarbon oxidation products between the gas and aerosol phases. While SOA formation is typically described in terms of partitioning only, the rate of formation and ultimate yield of SOA can also depend on the kinetics of both gas- and aerosol-phase processes. We present a general equilibrium/kinetic model of SOA formation that provides a framework for evaluating the extent to which the controlling mechanisms of SOA formation can be inferred from laboratory chamber data. With this model we examine the effect on SOA formation of gas-phase oxidation of first-generation products to either more or less volatile species, of particle-phase reaction (both first- and second-order kinetics), of the rate of parent hydrocarbon oxidation, and of the extent of reaction of the parent hydrocarbon. The effect of pre-existing organic aerosol mass on SOA yield, an issue of direct relevance to the translation of laboratory data to atmospheric applications, is examined. The importance of direct chemical measurements of gas- and particle-phase species is underscored in identifying SOA formation mechanisms.

Kinetic modeling of Secondary Organic Aerosol formation: effects of particle- and gas-phase reactions of semivolatile products

NASA Astrophysics Data System (ADS)

Chan, A. W. H.; Kroll, J. H.; Ng, N. L.; Seinfeld, J. H.

2007-05-01

The distinguishing mechanism of formation of secondary organic aerosol (SOA) is the partitioning of semivolatile hydrocarbon oxidation products between the gas and aerosol phases. While SOA formation is typically described in terms of partitioning only, the rate of formation and ultimate yield of SOA can also depend on the kinetics of both gas- and aerosol-phase processes. We present a general equilibrium/kinetic model of SOA formation that provides a framework for evaluating the extent to which the controlling mechanisms of SOA formation can be inferred from laboratory chamber data. With this model we examine the effect on SOA formation of gas-phase oxidation of first-generation products to either more or less volatile species, of particle-phase reaction (both first- and second-order kinetics), of the rate of parent hydrocarbon oxidation, and of the extent of reaction of the parent hydrocarbon. The effect of pre-existing organic aerosol mass on SOA yield, an issue of direct relevance to the translation of laboratory data to atmospheric applications, is examined. The importance of direct chemical measurements of gas- and particle-phase species is underscored in identifying SOA formation mechanisms.

Chemistry of fuel deposits and sediments and their predursors

NASA Technical Reports Server (NTRS)

Mayo, F. R.; Lan, B. Y.; Buttrill, S. E., Jr.; St.john, G. A.

1984-01-01

The mechanism of solid deposit formation on hot engine parts from turbine fuels is investigated. Deposit formation is associated with oxidation of the hydrocarbon fuel. Therefore, oxidation rates and soluble gum formation were measured for several jet turbine fuels and pure hydrocarbon mixtures. Experiments were performed at 130 C using thermal initiation and at 100 C using ditertiary butyl peroxide as a chemical initiator. Correlation of the data shows that the ratio of rate of oxidation to rate of gum formation for a single fuel is not much affected by experimental conditions, even though there are differences in the abilities of different hydrocarbons to initiate and continue the oxidation. This indicates a close association of gum formation with the oxidation process. Oxidations of n-dodecane, tetralin and the more unstable jet fuels are autocatalytic, while those of 2-ethylnaphthalene and a stable jet fuel are self-retarding. However, the ratio of oxidation rate to gum formation rate appear to be nearly constant for each substrate. The effect of oxygen pressure on gum and oxidation formation was also studied. Dependence of gum formation on the concentration of initiator at 100 C is discussed and problems for future study are suggested.

Gum and deposit formation from jet-turbine and diesel fuels at 130C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayo, F.R.; Lan, Bosco Y.

1986-01-01

The ultimate objective of this work is to devise an accelerated test to compare rates of soluble gum and deposit formation from jet-turbine and diesel fuels in storage and of hard deposits in engines. This paper describes rates of oxygen absorption and gum formation in air at 130 C. For a single fuel or hydrocarbon, the rate of gum formation is closely proportional to the oxygen absorbed, even when this rate varies with purification and additives. In general, pure hydrocarbons absorb oxygen much faster than the fuels, but the fuels and 2-ethylnaphthalene give more gum for the oxygen absorbed thanmore » the other pure hydrocarbons. Gum has two main sources; one appears to be associated with the chain termination mechanism in oxidation, the other coupling of fuel molecules in the absence of oxygen. Other possibilities are discussed.« less

Effect of hydrocarbon fuel type on fuel

NASA Technical Reports Server (NTRS)

Wong, E. L.; Bittker, D. A.

1982-01-01

A modified jet fuel thermal oxidation tester (JFTOT) procedure was used to evaluate deposit and sediment formation for four pure hydrocarbon fuels over the temperature range 150 to 450 C in 316-stainless-steel heater tubes. Fuel types were a normal alkane, an alkene, a naphthene, and an aromatic. Each fuel exhibited certain distinctive deposit and sediment formation characteristics. The effect of aluminum and 316-stainless-steel heater tube surfaces on deposit formation for the fuel n-decane over the same temperature range was investigated. Results showed that an aluminum surface had lower deposit formation rates at all temperatures investigated. By using a modified JFTOT procedure the thermal stability of four pure hydrocarbon fuels and two practical fuels (Jet A and home heating oil no. 2) was rated on the basis of their breakpoint temperatures. Results indicate that this method could be used to rate thermal stability for a series of fuels.

10 CFR 63.302 - Definitions for Subpart L.

Code of Federal Regulations, 2010 CFR

2010-01-01

...; and (5) The lithosphere. Aquifer means a water-bearing underground geological formation, group of formations, or part of a formation (excluding perched water bodies) that can yield a significant amount of ground water to a well or spring. Controlled area means: (1) The surface area, identified by passive...

10 CFR 63.302 - Definitions for Subpart L.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; and (5) The lithosphere. Aquifer means a water-bearing underground geological formation, group of formations, or part of a formation (excluding perched water bodies) that can yield a significant amount of ground water to a well or spring. Controlled area means: (1) The surface area, identified by passive...

Composition of pyrolysis gas from oil shale at various stages of heating

NASA Astrophysics Data System (ADS)

Martemyanov, S. M.; Bukharkin, A. A.; Koryashov, I. A.; Ivanov, A. A.

2017-05-01

Underground, the pyrolytic conversion of an oil shale in the nearest future may become an alternative source of a fuel gas and a synthetic oil. The main scientific problem in designing this technology is to provide a methodology for determination of the optimal mode of heating the subterranean formation. Such a methodology must allow predicting the composition of the pyrolysis products and the energy consumption at a given heating rate of the subterranean formation. The paper describes the results of heating of the oil shale fragments in conditions similar to the underground. The dynamics of composition of the gaseous products of pyrolysis are presented and analyzed.

Influence of hydrocarbon fuel structural constitution and flame temperature on soot formation in laminar diffusion flames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gulder, O.L.

1989-11-01

A systematic study of soot formation along the centerlines of axisymmetric laminar diffusion flames of a large number of liquid hydrocarbons, hydrocarbon blends, and transportation fuels were made. Measurements of the attenuation of a laser beam across the flame diameter were used to obtain the soot volume fraction, assuming Rayleigh extinction. Two sets of hydrocarbon blends were designed such that the molecular fuel composition varied considerably but the temperature fields in the flames were kept practically constant. Thus it was possible to separate the effects of molecular structure and the flame temperature on soot formation. It was quantitatively shown thatmore » the smoke height is a lumped measure of fuel molecular constitution and hydrogen-to-carbon ratio. Hydrocarbon fuel molecular composition was characterized by six carbon atom types that can be obtained, for complex hydrocarbon mixtures like transportation fuels, from proton nuclear magnetic resonance (/sup 1/H NMR) measurements. Strong attenuation of the laser beam was observed at heights very close to the burner rim. Visible flame profiles along the flame length were shown to have good self-similarity. Kent's model for diffusion flames was modified to include the effects of differences in flame temperatures and molecular diffusivities between fuels. An analysis based on the present data provides an assessment of the degree of contribution of different carbon atom types to the maximum soot volume fractions.« less

Using geothermal energy to heat a portion of a formation for an in situ heat treatment process

DOEpatents

Pieterson, Roelof; Boyles, Joseph Michael; Diebold, Peter Ulrich

2010-06-08

Methods of using geothermal energy to treat subsurface formations are described herein. Methods for using geothermal energy to treat a subsurface treatment area containing or proximate to hydrocarbons may include producing geothermally heated fluid from at least one subsurface region. Heat from at least a portion of the geothermally heated fluid may be transferred to the subsurface treatment area to heat the subsurface treatment area. At least some hydrocarbon fluids may be produced from the formation.

Syn-Rift Systems of East Godavari Sub Basin: Its Evolution and Hydrocarbon Prospectivity

NASA Astrophysics Data System (ADS)

Dash, J., Jr.; Zaman, B.

2014-12-01

Krishna Godavari (K.G.) basin is a passive margin basin developed along the Eastern coast of India. This basin has a polyhistoric evolution with multiple rift systems. Rift basin exploration has provided the oil and gas industry with almost one third of discovered global hydrocarbon resources. Understanding synrift sequences, their evolution, depositional styles and hydrocarbon prospectivity has become important with recent discovery of the wells, G-4-6,YS-AF and KG-8 in the K.G. offshore basin. The East Godavari subbasin is a hydrocarbon producing basin from synrift and pre-rift sediments, and hence this was selected as the study area for this research. The study has been carried out by utilizing data of around 58 wells (w1-w58) drilled in the study area 25 of which are hydrocarbon bearing with organic thickness varying from 200 m to 600 m. Age data generated by palaentology and palynology studies have been utilized for calibration of key well logs to differentiate between formations within prerift and synrift sediments. The electrologs of wells like resistivity, gamma ray, neutron, density and sonic logs have been utilized for correlation of different formations in all the drilled wells. The individual thicknesses of sand, shale and coal in the formations have been calculated and tabulated. For Golapalli formation, the isopach and isolith maps were generated which revealed that there were four depocentres with input from the north direction. Schematic geological cross sections were prepared using the well data and seismic data to understand the facies variation across the basin. The sedimentological and petrophysical analysis reports and electro log suites were referred to decipher the environment of deposition, the reservoir characteristics, and play types. The geochemical reports [w4 (Tmax)= 455-468 °C; w1 (Tmax) = 467-514 °C; w4(VRO)= 0.65-0.85; w1(VRO)= 0.83-1.13] revealed the source facies, its maturation and migration timings i.e. the petroleum systems. It was concluded these fluvial channel systems constitute the main hydrocarbon play for the Mandapeta and Gollapalli formations and these channel systems if found at a structurally advantageous positions should prove to be good hydrocarbon targets.

EFFECT OF HYDROCARBON COMPOSITION ON OXIDANT-HYDROCARBON RELATIONSHIPS. PHASE I. EXHAUST BLENDS FROM NON-CATALYST AND CATALYST EQUIPPED VEHICLES

EPA Science Inventory

Oxidation catalysts on automobiles not only reduce the total amount of hydrocarbon emissions, but also change the composition of these emissions significantly. To explore the effect of this change on oxidant formation, 28 ten-hour irradiations were carried out in the Exxon Resear...

The influence of shale depositional fabric on the kinetics of hydrocarbon generation through control of mineral surface contact area on clay catalysis

NASA Astrophysics Data System (ADS)

Rahman, Habibur M.; Kennedy, Martin; Löhr, Stefan; Dewhurst, David N.; Sherwood, Neil; Yang, Shengyu; Horsfield, Brian

2018-01-01

Accurately assessing the temperature and hence the depth and timing of hydrocarbon generation is a critical step in the characterization of a petroleum system. Clay catalysis is a potentially significant modifier of hydrocarbon generation temperature, but experimental studies of clay catalysis show inconsistent or contradictory results. This study tests the hypothesis that source rock fabric itself is an influence on clay mineral catalysis as it controls the extent to which organic matter and clay minerals are physically associated. Two endmember clay-organic fabrics distinguish the source rocks studied: (1) a particulate fabric where organic matter is present as discrete, >5 μm particles and (2) a nanocomposite fabric in which amorphous organic matter is associated with clay mineral surfaces at sub-micron scale. High-resolution electron imaging and bulk geochemical characterisation confirm that samples of the Miocene Monterey Formation (California) are representative of the nanocomposite source rock endmember, whereas samples from the Permian Stuart Range Formation (South Australia) represent the particulate source rock endmember. Kinetic experiments are performed on paired whole rock and kerogen isolate samples from these two formations using open system, non-isothermal pyrolysis at three different heating rates (0.7, 2 and 5 K/min) to determine the effects of the different shale fabrics on hydrocarbon generation kinetics. Extrapolation to a modelled geological heating rate shows a 20 °C reduction in the onset temperature of hydrocarbon generation in Monterey Formation whole rock samples relative to paired kerogen isolates. This result is consistent with the Monterey Formations's nanocomposite fabric where clay catalysis can proceed because reactive clay minerals are intimately associated with organic matter. By contrast, there is no significant difference in the modelled hydrocarbon generation temperature of paired whole rock and kerogen isolates from the Stuart Range Formation. This is consistent with its particulate fabric, where relatively large, discrete organic particles have limited contact with the mineral matrix and the clay minerals are mainly diagenetic and physically segregated within pores. While heating rate may have a control on mineral matrix effects, this result shows that the extent to which organic matter and clay minerals are physically associated could have a significant effect on the timing of hydrocarbon generation, and is a function of the depositional environment and detrital vs diagenetic origin of clay minerals in source rocks.

Hydrocarbons in recent sediment of the Monterey Bay National Marine Sanctuary

USGS Publications Warehouse

Kvenvolden, K.A.; Hostettler, F.D.; Rosenbauer, R.W.; Lorenson, T.D.; Castle, W.T.; Sugarman, S.

2002-01-01

A complex mixture of hydrocarbons is present in the recent sediment of the Monterey Bay National Marine Sanctuary. Eighteen samples from the continental shelf between San Francisco and Monterey contain aliphatic and aromatic hydrocarbons showing biological contributions from both marine and terrigenous sources, with the terrigenous indicators more pronounced near Monterey. Of particular interest, however, is a low-level background of petroleum-related compounds, including 28,30-bisnorhopane and 18??+??(H)-oleanane, which are characteristic of many crude oils from the Monterey Formation of California. Thus, the sediments are overprinted by a regional chemical signature which may be derived from eroded Monterey Formation rocks and from onshore and offshore seeps releasing petroleum from Monterey Formation source rocks. ?? 2002 Elsevier Science B.V. All rights reserved.

Two-step catalytic hydrodeoxygenation of fast pyrolysis oil to hydrocarbon liquid fuels.

PubMed

Xu, Xingmin; Zhang, Changsen; Liu, Yonggang; Zhai, Yunpu; Zhang, Ruiqin

2013-10-01

Two-step catalytic hydrodeoxygenation (HDO) of fast pyrolysis oil was investigated for translating pyrolysis oil to transportation grade hydrocarbon liquid fuels. At the first mild HDO step, various organic solvents were employed to promote HDO of bio-oil to overcome coke formation using noble catalyst (Ru/C) under mild conditions (300 °C, 10 MPa). At the second deep HDO step, conventional hydrogenation setup and catalyst (NiMo/Al2O3) were used under severe conditions (400 °C, 13 MPa) for obtaining hydrocarbon fuel. Results show that the phenomenon of coke formation is effectively eliminated, and the properties of products have been significantly improved, such as oxygen content decreases from 48 to 0.5 wt% and high heating value increases from 17 to 46 MJ kg(-1). GC-MS analysis indicates that the final products include C11-C27 aliphatic hydrocarbons and aromatic hydrocarbons. In short, the fast pyrolysis oils were successfully translated to hydrocarbon liquid fuels using a two-step catalytic HDO process. Copyright © 2013 Elsevier Ltd. All rights reserved.

Fast co-pyrolysis of waste newspaper with high-density polyethylene for high yields of alcohols and hydrocarbons.

PubMed

Chen, Weimin; Shi, Shukai; Chen, Minzhi; Zhou, Xiaoyan

2017-09-01

Waste newspaper (WP) was first co-pyrolyzed with high-density polyethylene (HDPE) using pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) to enhance the yields of alcohols and hydrocarbons. The effects of WP: HDPE feed ratio (100:0, 75:25, 50:50, 25:75, 0:100) and temperature (500-800°C) on products distribution were investigated and the interaction mechanism during co-pyrolysis was also proposed. Maximum yields of alcohols and hydrocarbons reached 85.88% (feed ratio 50:50wt.%, 600°C). Hydrogen supplements and deoxidation by HDPE and subsequently fragments recombination result in the conversion of aldehydes and ketones into branched hydrocarbons. Radicals from WP degradation favor the secondary crack for HDPE products resulting in the formation of linear hydrocarbons with low carbon number. Hydrocarbons with activated radical site from HDPE degradation were interacted with hydroxyl from WP degradation promoting the formation of linear long chain alcohols. Moreover, co-pyrolysis significantly enhanced condensable oil qualities, which were close to commercial diesel No. 0. Copyright © 2017 Elsevier Ltd. All rights reserved.

Varying properties of in situ heat treatment of a tar sands formation based on assessed viscosities

DOEpatents

Karanikas, John Michael; Vinegar, Harold J

2014-03-04

A method for treating a tar sands formation includes providing heat to at least part of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat is allowed to transfer from the heaters to at least a portion of the formation. A viscosity of one or more zones of the hydrocarbon layer is assessed. The heating rates in the zones are varied based on the assessed viscosities. The heating rate in a first zone of the formation is greater than the heating rate in a second zone of the formation if the viscosity in the first zone is greater than the viscosity in the second zone. Fluids are produced from the formation through the production wells.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir (Appendix)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael; Booth, Robert; Fairchild, James

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Hybrid Technology of Hard Coal Mining from Seams Located at Great Depths

NASA Astrophysics Data System (ADS)

Czaja, Piotr; Kamiński, Paweł; Klich, Jerzy; Tajduś, Antoni

2014-10-01

Learning to control fire changed the life of man considerably. Learning to convert the energy derived from combustion of coal or hydrocarbons into another type of energy, such as steam pressure or electricity, has put him on the path of scientific and technological revolution, stimulating dynamic development. Since the dawn of time, fossil fuels have been serving as the mankind's natural reservoir of energy in an increasingly great capacity. A completely incomprehensible refusal to use fossil fuels causes some local populations, who do not possess a comprehensive knowledge of the subject, to protest and even generate social conflicts as an expression of their dislike for the extraction of minerals. Our times are marked by the search for more efficient ways of utilizing fossil fuels by introducing non-conventional technologies of exploiting conventional energy sources. During apartheid, South Africa demonstrated that cheap coal can easily satisfy total demand for liquid and gaseous fuels. In consideration of current high prices of hydrocarbon media (oil and gas), gasification or liquefaction of coal seems to be the innovative technology convergent with contemporary expectations of both energy producers as well as environmentalists. Known mainly from literature reports, underground coal gasification technologies can be brought down to two basic methods: - shaftless method - drilling, in which the gasified seam is uncovered using boreholes drilled from the surface, - shaft method, in which the existing infrastructure of underground mines is used to uncover the seams. This paper presents a hybrid shaft-drilling approach to the acquisition of primary energy carriers (methane and syngas) from coal seams located at great depths. A major advantage of this method is the fact that the use of conventional coal mining technology requires the seams located at great depths to be placed on the off-balance sheet, while the hybrid method of underground gasification enables them to become a source of additional energy for the economy. It should be noted, however, that the shaft-drilling method cannot be considered as an alternative to conventional methods of coal extraction, but rather as a complementary and cheaper way of utilizing resources located almost beyond the technical capabilities of conventional extraction methods due to the associated natural hazards and high costs of combating them. This article presents a completely different approach to the issue of underground coal gasification. Repurposing of the already fully depreciated mining infrastructure for the gasification process may result in a large value added of synthesis gas production and very positive economic effect.

System for fracturing an underground geologic formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mace, Jonathan L.; Tappan, Bryce C.; Seitz, Gerald J.

2017-03-14

An explosive system for fracturing an underground geologic formation adjacent to a wellbore can comprise a plurality of explosive units comprising an explosive material contained within the casing, and detonation control modules electrically coupled to the plurality of explosive units and configured to cause a power pulse to be transmitted to at least one detonator of at least one of the plurality of explosive units for detonation of the explosive material. The explosive units are configured to be positioned within a wellbore in spaced apart positions relative to one another along a string with the detonation control modules positioned adjacentmore » to the plurality of explosive units in the wellbore, such that the axial positions of the explosive units relative to the wellbore are at least partially based on geologic properties of the geologic formation adjacent the wellbore.« less

Relevance of deep-subsurface microbiology for underground gas storage and geothermal energy production.

PubMed

Gniese, Claudia; Bombach, Petra; Rakoczy, Jana; Hoth, Nils; Schlömann, Michael; Richnow, Hans-Hermann; Krüger, Martin

2014-01-01

This chapter gives the reader an introduction into the microbiology of deep geological systems with a special focus on potential geobiotechnological applications and respective risk assessments. It has been known for decades that microbial activity is responsible for the degradation or conversion of hydrocarbons in oil, gas, and coal reservoirs. These processes occur in the absence of oxygen, a typical characteristic of such deep ecosystems. The understanding of the responsible microbial processes and their environmental regulation is not only of great scientific interest. It also has substantial economic and social relevance, inasmuch as these processes directly or indirectly affect the quantity and quality of the stored oil or gas. As outlined in the following chapter, in addition to the conventional hydrocarbons, new interest in such deep subsurface systems is rising for different technological developments. These are introduced together with related geomicrobiological topics. The capture and long-termed storage of large amounts of carbon dioxide, carbon capture and storage (CCS), for example, in depleted oil and gas reservoirs, is considered to be an important options to mitigate greenhouse gas emissions and global warming. On the other hand, the increasing contribution of energy from natural and renewable sources, such as wind, solar, geothermal energy, or biogas production leads to an increasing interest in underground storage of renewable energies. Energy carriers, that is, biogas, methane, or hydrogen, are often produced in a nonconstant manner and renewable energy may be produced at some distance from the place where it is needed. Therefore, storing the energy after its conversion to methane or hydrogen in porous reservoirs or salt caverns is extensively discussed. All these developments create new research fields and challenges for microbiologists and geobiotechnologists. As a basis for respective future work, we introduce the three major topics, that is, CCS, underground storage of gases from renewable energy production, and the production of geothermal energy, and summarize the current stat of knowledge about related geomicrobiological and geobiotechnological aspects in this chapter. Finally, recommendations are made for future research.

Regional Jurassic geologic framework of Alabama coastal waters area and adjacent Federal waters area

USGS Publications Warehouse

Mink, R.M.; Bearden, B.L.; Mancini, E.A.

1989-01-01

To date, numerous Jurassic hydrocarbon fields and pools have been discovered in the Cotton Valley Group, Haynesville Formation, Smackover Formation and Norphlet Formation in the tri-state area of Mississippi, Alabama and Florida, and in Alabama State coastal waters and adjacent Federal waters area. Petroleum traps are basement highs, salt anticlines, faulted salt anticlines and extensional faults associated with salt movement. Reservoirs include continental and marine sandstones, limestones and dolostones. Hydrocarbon types are oil, condensate and natural gas. The onshore stratigraphic and structural information can be used to establish a regional geologic framework for the Jurassic for the State coastal waters and adjacent Federal waters areas. Evaluation of the geologic information along with the hydrocarbon data from the tri-state area indicates that at least three Jurassic hydrocarbon trends (oil, oil and gas condensate, and deep natural gas) can be identified onshore. These onshore hydrocarbon trends can be projected into the Mobile area in the Central Gulf of Mexico and into the Pensacola, Destin Dome and Apalachicola areas in the Eastern Gulf of Mexico. Substantial reserves of natural gas are expected to be present in Alabama State waters and the northern portion of the Mobile area. Significant accumulations of oil and gas condensate may be encountered in the Pensacola, Destin Dome, and Apalachicola areas. ?? 1989.

Solution mining systems and methods for treating hydrocarbon containing formations

DOEpatents

Vinegar, Harold J [Bellaire, TX; de Rouffignac, Eric Pierre [Rijswijk, NL; Schoeling, Lanny Gene [Katy, TX

2009-07-14

A method for treating an oil shale formation comprising nahcolite is disclosed. The method includes providing a first fluid to a portion of the formation through at least two injection wells. A second fluid is produced from the portion through at least one injection well until at least two injection wells are interconnected such that fluid can flow between the two injection wells. The second fluid includes at least some nahcolite dissolved in the first fluid. The first fluid is injected through one of the interconnected injection wells. The second fluid is produced from at least one of the interconnected injection wells. Heat is provided from one or more heaters to the formation to heat the formation. Hydrocarbon fluids are produced from the formation.

Stacking faults and mechanisms strain-induced transformations of hcp metals (Ti, Mg) during mechanical activation in liquid hydrocarbons

NASA Astrophysics Data System (ADS)

Lubnin, A. N.; Dorofeev, G. A.; Nikonova, R. M.; Mukhgalin, V. V.; Lad'yanov, V. I.

2017-11-01

The evolution of the structure and substructure of metals Ti and Mg with hexagonal close-packed (hcp) lattice is studied during their mechanical activation in a planetary ball mill in liquid hydrocarbons (toluene, n-heptane) and with additions of carbon materials (graphite, fullerite, nanotubes) by X-ray diffraction, scanning electron microscopy, and chemical analysis. The temperature behavior and hydrogen-accumulating properties of mechanocomposites are studied. During mechanical activation of Ti and Mg, liquid hydrocarbons decay, metastable nanocrystalline titanium carbohydride Ti(C,H) x and magnesium hydride β-MgH2 are formed, respectively. The Ti(C,H) x and MgH2 formation mechanisms during mechanical activation are deformation ones and are associated with stacking faults accumulation, and the formation of face-centered cubic (fcc) packing of atoms. Metastable Ti(C,H)x decays at a temperature of 550°C, the partial reverse transformation fcc → hcp occurs. The crystalline defect accumulation (nanograin boundaries, stacking faults), hydrocarbon destruction, and mechanocomposite formation leads to the enhancement of subsequent magnesium hydrogenation in the Sieverts reactor.

Polycyclic aromatic hydrocarbon formation during the gasification of sewage sludge in sub- and supercritical water: Effect of reaction parameters and reaction pathways.

PubMed

Gong, Miao; Wang, Yulan; Fan, Yujie; Zhu, Wei; Zhang, Huiwen; Su, Ying

2018-02-01

The formation of polycyclic aromatic hydrocarbon is a widespread issue during the supercritical water gasification of sewage sludge, which directly reduces the gasification efficiency and restricts the technology practical application. The changes of the concentrations and forms as well as the synthesis rate of polycyclic aromatic hydrocarbons in the residues from supercritical water gasification of dewatered sewage sludge were investigated to understand influence factors and the reaction pathways. Results showed that the increase of reaction temperature during the heating period favours directly concentration of polycyclic aromatic hydrocarbon (especially higher-molecular-weight), especially when it raise above 300 °C. Lower heating and cooling rate essentially extend the total reaction time. Higher polycyclic aromatic hydrocarbon concentration and higher number of rings were generally promoted by lower heating and cooling rate, longer reaction time and higher reaction temperature. The lower-molecular-weight polycyclic aromatic hydrocarbons can be directly generated through the decomposition of aromatic-containing compounds in sewage sludge, as well as 3-ring and 4-ring polycyclic aromatic hydrocarbons can be formed by aromatization of steroids. Possible mechanisms of reaction pathways of supercritical water gasification of sewage sludge were also proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Shale characterization on Barito field, Southeast Kalimantan for shale hydrocarbon exploration

NASA Astrophysics Data System (ADS)

Sumotarto, T. A.; Haris, A.; Riyanto, A.; Usman, A.

2017-07-01

Exploration and exploitation in Indonesia now are still focused on conventional hydrocarbon energy than unconventional hydrocarbon energy such as shale gas. Tanjung Formation is a source rock of Barito Basin located in South Kalimantan that potentially as shale hydrocarbon. In this research, integrated methods using geochemical analysis, mineralogy, petrophysical analysis and seismic interpretation has been applied to explore the shale hydrocarbon potential in Barito Field for Tanjung formation. The first step is conducting geochemical and mineralogy analysis to the shale rock sample. Our analysis shows that the organic richness is ranging from 1.26-5.98 wt.% (good to excellent) with the depth of early mature window of 2170 m. The brittleness index is in an average of 0.44-0.56 (less Brittle) and Kerogen type is classified into II/III type that potentially produces oil and gas. The second step is continued by performing petrophysical analysis, which includes Total Organic Carbon (TOC) calculation and brittleness index continuously. The result has been validated with a laboratory measurement that obtained a good correlation. In addition, seismic interpretation based on inverted acoustic impedance is applied to map the distributions of shale hydrocarbon potential. Our interpretation shows that shale hydrocarbon potential is localized in the eastern and southeastern part of the study area.

Genesis of Miocene litho-stratigraphic trap and hydrocarbon accumulation in the Qiongdongnan Basin, northern South China Sea

NASA Astrophysics Data System (ADS)

Fan, Caiwei; Jiang, Tao; Liu, Kun; Tan, Jiancai; Li, Hu; Li, Anqi

2018-12-01

In recent years, several large gas fields have been discovered in western Qiongdongnan Basin. It is important and necessary to illustrate their sedimentary characteristics and hydrocarbon migration so that more gas fields could be discovered in the future. Previous regional tectonic-sedimentary researchers show that large-scale source rock of the Yacheng Formation developed in the Ledong and Lingshui sags due to the Red River Fault pull-apart strike slip in early Oligocene. The main targets for hydrocarbon exploration in this area are the Miocene deep water reservoirs. In late Miocene, the Huangliu Formation reservoirs are composed of the early channels which were sourced by river systems in Hainan uplift and the consequent channels were sourced by Qiupen River in Kunsong uplift. Both axial channels exhibit unique spatial distribution patterns and geometries. The other kind of reservoir developed in the middle Miocene Meishan Formation, which compose of slope break-controlled submarine fan. They can be further classified into three types—slope channelized fan, basin floor fan, and bottom current reworked fan. The various fans have different reservoir quality. These two kinds of reservoirs contribute to four types of litho-stratigraphic traps under the actions of sedimentation and subsidence. The overpressure caused by hydrocarbon generation can fracture deeper strata and result in regional fractured network for hydrocarbon migration. Therefore, free gas driven by overpressure and buoyancy force can be migrated into Miocene litho-stratigraphic traps to accumulate. The revealed genesis of Miocene lithologic trap and hydrocarbon accumulation in the Qiongdongnan Basin would greatly contribute to the further hydrocarbon exploration in northern South China Sea and can be helpful for other deep water areas around the world.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

Technical Feasibility of Compressed Air Energy Storage (CAES) Utilizing a Porous Rock Reservoir, Appendix — Chapter 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, Michael

Pacific Gas & Electric Company (PG&E) conducted a project to explore the viability of underground compressed air energy storage (CAES) technology. CAES uses low-cost, off-peak electricity to compress air into a storage system in an underground space such as a rock formation or salt cavern. When electricity is needed, the air is withdrawn and used to drive a generator for electricity production.

40 CFR 146.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS General Provisions § 146.3 Definitions. The following definitions apply to the underground injection control program. Abandoned well means a well whose use has been... Part B of the RCRA application). Aquifer means a geological formation, group of formations, or part of...

40 CFR 146.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS General Provisions § 146.3 Definitions. The following definitions apply to the underground injection control program. Abandoned well means a well whose use has been... Part B of the RCRA application). Aquifer means a geological formation, group of formations, or part of...

40 CFR 146.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS General Provisions § 146.3 Definitions. The following definitions apply to the underground injection control program. Abandoned well means a well whose use has been... Part B of the RCRA application). Aquifer means a geological formation, group of formations, or part of...

Injection-induced earthquakes

USGS Publications Warehouse

Ellsworth, William L.

2013-01-01

Earthquakes in unusual locations have become an important topic of discussion in both North America and Europe, owing to the concern that industrial activity could cause damaging earthquakes. It has long been understood that earthquakes can be induced by impoundment of reservoirs, surface and underground mining, withdrawal of fluids and gas from the subsurface, and injection of fluids into underground formations. Injection-induced earthquakes have, in particular, become a focus of discussion as the application of hydraulic fracturing to tight shale formations is enabling the production of oil and gas from previously unproductive formations. Earthquakes can be induced as part of the process to stimulate the production from tight shale formations, or by disposal of wastewater associated with stimulation and production. Here, I review recent seismic activity that may be associated with industrial activity, with a focus on the disposal of wastewater by injection in deep wells; assess the scientific understanding of induced earthquakes; and discuss the key scientific challenges to be met for assessing this hazard.

Numerical Simulation of Convective Heat and Mass Transfer in a Two-Layer System

NASA Astrophysics Data System (ADS)

Myznikova, B. I.; Kazaryan, V. A.; Tarunin, E. L.; Wertgeim, I. I.

The results are presented of mathematical and computer modeling of natural convection in the “liquid-gas” two-layer system, filling a vertical cylinder surrounded by solid heat conductive tract. The model describes approximately the conjugate heat and mass transfer in the underground oil product storage, filled partially by a hydrocarbon liquid, with natural gas layer above the liquid surface. The geothermal gradient in a rock mass gives rise to the intensive convection in the liquid-gas system. The consideration is worked out for laminar flows, laminar-turbulent transitional regimes, and developed turbulent flows.

Apparatus for recovering gaseous hydrocarbons from hydrocarbon-containing solid hydrates

DOEpatents

Elliott, Guy R. B.; Barraclough, Bruce L.; Vanderborgh, Nicholas E.

1984-01-01

A method and apparatus are provided for producing gaseous hydrocarbons from formations comprising solid hydrocarbon hydrates located under either a body of land or a body of water. The vast natural resources of such hydrocarbon hydrates can thus now be economically mined. Relatively warm brine or water is brought down from an elevation above that of the hydrates through a portion of the apparatus and passes in contact with the hydrates, thus melting them. The liquid then continues up another portion of the apparatus, carrying entrained hydrocarbon vapors in the form of bubbles, which can easily be separated from the liquid. After a short startup procedure, the process and apparatus are substantially self-powered.

Direct Detection of Hardly Detectable Hidden Chirality of Hydrocarbons and Deuterated Isotopomers by a Helical Polyacetylene through Chiral Amplification and Memory.

PubMed

Maeda, Katsuhiro; Hirose, Daisuke; Okoshi, Natsuki; Shimomura, Kouhei; Wada, Yuya; Ikai, Tomoyuki; Kanoh, Shigeyoshi; Yashima, Eiji

2018-03-07

We report the first direct chirality sensing of a series of chiral hydrocarbons and isotopically chiral compounds (deuterated isotopomers), which are almost impossible to detect by conventional optical spectroscopic methods, by a stereoregular polyacetylene bearing 2,2'-biphenol-derived pendants. The polyacetylene showed a circular dichroism due to a preferred-handed helix formation in response to the hardly detectable hidden chirality of saturated tertiary or chiroptical quaternary hydrocarbons, and deuterated isotopomers. In sharp contrast to the previously reported sensory systems, the chirality detection by the polyacetylene relies on an excess one-handed helix formation induced by the chiral hydrocarbons and deuterated isotopomers via significant amplification of the chirality followed by its static memory, through which chiral information on the minute and hidden chirality can be stored as an excess of a single-handed helix memory for a long time.

Methods of using structures including catalytic materials disposed within porous zeolite materials to synthesize hydrocarbons

DOEpatents

Rollins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID

2011-02-01

Catalytic structures include a catalytic material disposed within a zeolite material. The catalytic material may be capable of catalyzing a formation of methanol from carbon monoxide and/or carbon dioxide, and the zeolite material may be capable of catalyzing a formation of hydrocarbon molecules from methanol. The catalytic material may include copper and zinc oxide. The zeolite material may include a first plurality of pores substantially defined by a crystal structure of the zeolite material and a second plurality of pores dispersed throughout the zeolite material. Systems for synthesizing hydrocarbon molecules also include catalytic structures. Methods for synthesizing hydrocarbon molecules include contacting hydrogen and at least one of carbon monoxide and carbon dioxide with such catalytic structures. Catalytic structures are fabricated by forming a zeolite material at least partially around a template structure, removing the template structure, and introducing a catalytic material into the zeolite material.

Systems including catalysts in porous zeolite materials within a reactor for use in synthesizing hydrocarbons

DOEpatents

Rolllins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID

2012-07-24

Catalytic structures include a catalytic material disposed within a zeolite material. The catalytic material may be capable of catalyzing a formation of methanol from carbon monoxide and/or carbon dioxide, and the zeolite material may be capable of catalyzing a formation of hydrocarbon molecules from methanol. The catalytic material may include copper and zinc oxide. The zeolite material may include a first plurality of pores substantially defined by a crystal structure of the zeolite material and a second plurality of pores dispersed throughout the zeolite material. Systems for synthesizing hydrocarbon molecules also include catalytic structures. Methods for synthesizing hydrocarbon molecules include contacting hydrogen and at least one of carbon monoxide and carbon dioxide with such catalytic structures. Catalytic structures are fabricated by forming a zeolite material at least partially around a template structure, removing the template structure, and introducing a catalytic material into the zeolite material.

Topical viscosity control for light hydrocarbon displacing fluids in petroleum recovery and in fracturing fluids for well stimulation

DOEpatents

Heller, John P.; Dandge, Dileep K.

1986-01-01

Solvent-type flooding fluids comprising light hydrocarbons in the range of ethane to hexane (and mixtures thereof) are used to displace crude oil in formations having temperatures of about 20 degrees to about 150 degrees Centigrade and pressures above about 650 psi, the light hydrocarbons having dissolved therein from about 0.05% to about 3% of an organotin compound of the formula R.sub.3 SnF where each R is independently an alkyl, aryl or alkyaryl group from 3 to 12 carbon atoms. Under the pressures and temperatures described, the organotin compounds become pentacoordinated and linked through the electronegative bridges, forming polymers within the light hydrocarbon flooding media to render them highly viscous. Under ambient conditions, the viscosity control agents will not readily be produced from the formation with either crude oil or water, since they are insoluble in the former and only sparingly soluble in the latter.

Shock tube study of the fuel structure effects on the chemical kinetic mechanisms responsible for soot formation

NASA Technical Reports Server (NTRS)

Frenklach, M.

1983-01-01

Soot formation in toluene-, benzene-, and acetylene-oxygen-argon mixtures was investigated to study soot formation in a combustion environment. High concentrations of oxygen completely suppress soot formation. The addition of oxygen at relatively low concentrations uniformly suppresses soot formation at high pressures, while at relatively lower pressures it suppresses soot formation at higher temperatures while promoting soot production at lower temperatures. The observed behavior indicates that oxidation reactions compete with ring fragmentation. The main conclusion to be drawn from the results is that the soot formation mechanism is probably the same for the pyrolysis and oxidation of hydrocarbons. That is, the addition of oxygen does not alter the soot route but rather promotes or inhibits this route by means of competitive reactions. An approach to empirical modeling of soot formation during pyrolysis of aromatic hydrocarbons is also presented.

Poster 4: Investigating the first steps of hydrocarbon condensation in the laboratory and in Titan's atmosphere

NASA Astrophysics Data System (ADS)

Biennier, Ludovic; Bourgalais, Jeremy; Benidar, Abdessamad; Le Picard, Sebastien

2016-06-01

Hydrocarbons formed in Titan's cold atmosphere, starting with ethane C2H6, ethylene C2H4, acetylene C2H2, propane C3H8,... up to benzene C6H6, play some role in aerosol production, cloud processes, rain generation and Titan's lakes formation. We have started to study in the laboratory the kinetics of the first steps of condensation of these hydrocarbons. Rate coefficients are very sensitive to the description of the potential interaction surfaces of the molecules involved. Combined theoretical and experimental studies at the molecular level of the homogenous nucleation of various small molecules should improve greatly our fundamental understanding. This knowledge will serve as a model for studying more complex nucleation processes actually taking places in planetary atmospheres. Here we present the first experimental kinetic study of the dimerization of two small hydrocarbons: ethane C2H6 and propane C3H8. We have performed experiments to identify the temperature and partial densities ranges over which small hydrocarbon clusters form in saturated uniform supersonic flows. Using our unique reactor based on a Laval nozzle expansions, the kinetics of the formation has also been investigated down to 23 K. The chemical species present in the reactor are probed by a time of flight mass spectrometer equipped with an electron gun for soft ionization of the neutral reagents and products. This work aims at putting some constraints on the role of small hydrocarbon condensation in the formation of haze particles in the dense atmosphere of Titan.

Creating fluid injectivity in tar sands formations

DOEpatents

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2010-06-08

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

In-situ laser retorting of oil shale

NASA Technical Reports Server (NTRS)

Bloomfield, H. S. (Inventor)

1977-01-01

Oil shale formations are retorted in situ and gaseous hydrocarbon products are recovered by drilling two or more wells into an oil shale formation underneath the surface of the ground. A high energy laser beam is directed into the well and fractures the region of the shale formation. A compressed gas is forced into the well that supports combustion in the flame front ignited by the laser beam, thereby retorting the oil shale. Gaseous hydrocarbon products which permeate through the fractured region are recovered from one of the wells that were not exposed to the laser system.

Evidence that Polycyclic Aromatic Hydrocarbons in Two Carbonaceous Chondrites Predate Parent-Body Formation

NASA Technical Reports Server (NTRS)

Plows, F. L.; Elsila, J. E.; Zare, R. N.; Buseck, P. R.

2003-01-01

Organic material in meteorites provides insight into the cosmochemistry of the early solar system. The distribution of polycyclic aromatic hydrocarbons (PAHs) in the Allende and Murchison carbonaceous chondrites was investigated using spatially resolved microprobe laser-desorption laser-ionization mass spectrometry. Sharp chemical gradients of PAHs are associated with specific meteorite features. The ratios of various PAH intensities relative to the smallest PAH, naphthalene, are nearly constant across the sample. These findings suggest a common origin for PAHs dating prior to or contemporary with the formation of the parent body, consistent with proposed interstellar formation mechanisms.

Heating hydrocarbon containing formations in a spiral startup staged sequence

DOEpatents

Vinegar, Harold J [Bellaire, TX; Miller, David Scott [Katy, TX

2009-12-15

Methods for treating a hydrocarbon containing formation are described herein. Methods may include treating a first zone of the formation. Treatment of a plurality of zones of the formation may be begun at selected times after the treatment of the first zone begins. The treatment of at least two successively treated zones may begin at a selected time after treatment of the previous zone begins. At least two of the successively treated zones may be adjacent to the zone treated previously. The successive treatment of the zones proceeds in an outward, substantially spiral sequence from the first zone so that the treatment of the zones may move substantially spirally outwards towards a boundary of the treatment area.

40 CFR 445.1 - General applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., waste piles, salt dome formations, salt bed formations, underground mines or caves as these terms are... ground water or wastewater from recovery pumping wells. (e) This part does not apply to discharges of... Treatment (CWT) facilities subject to 40 CFR part 437 so long as the CWT facility commingles the landfill...

Effects of hydrocarbon contamination on ozone generation with dielectric barrier discharges

NASA Astrophysics Data System (ADS)

Lopez, Jose L.; Vezzu, Guido; Freilich, Alfred; Paolini, Bernhard

2013-08-01

The increasing usage of the feed gases of lower grade liquid oxygen (LOX) containing higher levels of trace hydrocarbon impurities in dielectric barrier discharge (DBD) for ozone generation requires a better understanding of the kinetics of the by-product formation resulting from reactions involving these hydrocarbon impurities. As a case study of hydrocarbon impurities, the kinetics of CH4 conversion in DBDs and the subsequent HNO3 formation were investigated by means of gas-phase plasma diagnostics, supported by detailed process modeling, and extensive in-situ and ex-situ by-product analysis. The by-products formation in the plasma with the presence of CH4, were found to differ significantly in oxygen-fed generators as compared to generators fed with oxygen/nitrogen mixtures. The amount of HNO3 formed depends on the concentration of NOx formed in the plasma and the amount of CH4 that is converted, but not on the O3 concentration. In the present work we have investigated CH4 concentrations of up to 1.95 wt% of the feed gas. The rate of deterioration of the overall ozone generator performance was found to be affected by the concentration of nitrogen in the oxygen/nitrogen mixture.

Substantially self-powered method and apparatus for recovering hydrocarbons from hydrocarbon-containing solid hydrates

DOEpatents

Elliott, G.R.B.; Barraclough, B.L.; Vanderborgh, N.E.

1981-02-19

A method and apparatus are provided for producing gaseous hydrocarbons from formations comprising solid hydrocarbon hydrates located under either a body of land or a body of water. The vast natural resources of such hydrocarbon hydrates can thus now be economically mined. Relatively warm brine or water is brought down from an elevation above that of the hydrates through a portion of the apparatus, and passes in contact with the hydrates, thus melting them. The liquid then continues up another portion of the apparatus carrying entrained hydrocarbon vapors in the form of bubbles, which can easily be separated from the liquid. After a short startup procedure, the process and apparatus are substantially self-powered.

Substantially self-powered method and apparatus for recovering hydrocarbons from hydrocarbon-containing solid hydrates

DOEpatents

Elliott, Guy R. B.; Barraclough, Bruce L.; Vanderborgh, Nicholas E.

1983-01-01

A method and apparatus are provided for producing gaseous hydrocarbons from formations comprising solid hydrocarbon hydrates located under either a body of land or a body of water. The vast natural resources of such hydrocarbon hydrates can thus now be economically mined. Relatively warm brine or water is brought down from an elevation above that of the hydrates through a portion of the apparatus and passes in contact with the hydrates, thus melting them. The liquid then continues up another portion of the apparatus, carrying entrained hydrocarbon vapors in the form of bubbles, which can easily be separated from the liquid. After a short startup procedure, the process and apparatus are substantially self-powered.

Diversity and role of plasmids in adaptation of bacteria inhabiting the Lubin copper mine in Poland, an environment rich in heavy metals.

PubMed

Dziewit, Lukasz; Pyzik, Adam; Szuplewska, Magdalena; Matlakowska, Renata; Mielnicki, Sebastian; Wibberg, Daniel; Schlüter, Andreas; Pühler, Alfred; Bartosik, Dariusz

2015-01-01

The Lubin underground mine, is one of three mining divisions in the Lubin-Glogow Copper District in Lower Silesia province (Poland). It is the source of polymetallic ore that is rich in copper, silver and several heavy metals. Black shale is also significantly enriched in fossil organic matter in the form of long-chain hydrocarbons, polycyclic aromatic hydrocarbons, organic acids, esters, thiophenes and metalloporphyrins. Biological analyses have revealed that this environment is inhabited by extremophilic bacteria and fungi. Kupfershiefer black shale and samples of water, bottom and mineral sediments from the underground (below 600 m) Lubin mine were taken and 20 bacterial strains were isolated and characterized. All exhibited multi-resistant and hypertolerant phenotypes to heavy metals. We analyzed the plasmidome of these strains in order to evaluate the diversity and role of mobile DNA in adaptation to the harsh conditions of the mine environment. Experimental and bioinformatic analyses of 11 extrachromosomal replicons were performed. Three plasmids, including a broad-host-range replicon containing a Tn3 family transposon, carried genes conferring resistance to arsenic, cadmium, cobalt, mercury and zinc. Functional analysis revealed that the resistance modules exhibit host specificity, i.e., they may increase or decrease tolerance to toxic ions depending on the host strain. The other identified replicons showed diverse features. Among them we identified a catabolic plasmid encoding enzymes involved in the utilization of histidine and vanillate, a putative plasmid-like prophage carrying genes responsible for NAD biosynthesis, and two repABC-type plasmids containing virulence-associated genes. These findings provide an unique molecular insight into the pool of extrachromosomal replicons and highlight their role in the biology and adaptation of extremophilic bacteria inhabiting terrestrial deep subsurface.

Bioremediation of diesel contamination at an underground storage tank site: a spatial analysis of the microbial community.

PubMed

Andreolli, Marco; Albertarelli, Nicola; Lampis, Silvia; Brignoli, Pierlorenzo; Khoei, Nazaninalsadat Seyed; Vallini, Giovanni

2016-01-01

The present study reports on a real case of contamination due to the chronic leakage of diesel fuel from an underground tank at a dismissed service station. Speciation of the microbial community according to both lateral and vertical gradients from the origin of the contaminant release was analyzed by means of the PCR-DGGE technique. Moreover, the effects of a landfarming treatment on both the microbial community structure and the abatement of contamination were analyzed. The concentration of total petrol hydrocarbons (TPHs) decreased along the horizontal gradient (from 7042.2 ± 521.9 to 112.2 ± 24.3 mg kg(-1)), while increased downwards from the position of the tank (from 502.6 ± 43.7 to 4972.5 ± 275.3 mg kg(-1)). PCR-DGGE analyses and further statistical treatment of the data indicated a correlation between structure of the bacterial communities and amount of diesel fuel contamination. On the other hand, level of contamination, soil texture and depth were shown to affect the fungal community. Chloroflexi and Ascomycota were the most abundant microbes ascertained through culture-independent procedures. Landfarming promoted 91.6 % reduction of TPHs in 75 days. Furthermore, PCR-DGGE analyses evidenced that both bacterial and fungal communities of the treated soil were restored to the pristine conditions of uncontaminated topsoil. The present study demonstrated that bacterial and fungal communities were affected differently by soil factors such as level of hydrocarbon contamination as well as soil depth and texture. This report shows that a well-planned landfarming treatment can drive the restoration of the soil in terms of both abatement of the contaminants and resilience of the microbial community structure.

Monitoring of atmospheric gaseous and particulate polycyclic aromatic hydrocarbons in South African platinum mines utilising portable denuder sampling with analysis by thermal desorption-comprehensive gas chromatography-mass spectrometry.

PubMed

Geldenhuys, G; Rohwer, E R; Naudé, Y; Forbes, P B C

2015-02-06

Concentrations of diesel particulate matter and polycyclic aromatic hydrocarbons (PAHs) in platinum mine environments are likely to be higher than in ambient air due to the use of diesel machinery in confined environments. Airborne PAHs may be present in gaseous or particle phases each of which has different human health impacts due to their ultimate fate in the body. Here we report on the simultaneous sampling of both phases of airborne PAHs for the first time in underground platinum mines in South Africa, which was made possible by employing small, portable denuder sampling devices consisting of two polydimethylsiloxane (PDMS) multi-channel traps connected in series separated by a quartz fibre filter, which only require small, battery operated portable personal sampling pumps for air sampling. Thermal desorption coupled with comprehensive gas chromatography-mass spectrometry (TD-GC×GC-TofMS) was used to analyse denuder samples taken in three different platinum mines. The samples from a range of underground environments revealed that PAHs were predominantly found in the gas phase with naphthalene and mono-methylated naphthalene derivatives being detected at the highest concentrations ranging from 0.01 to 18 μg m(-3). The particle bound PAHs were found in the highest concentrations at the idling load haul dump vehicle exhausts with a dominance of fluoranthene and pyrene. Particle associated PAH concentrations ranged from 0.47 to 260 ng m(-3) and included benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene. This work highlights the need to characterise both phases in order to assess occupational exposure to PAHs in this challenging sampling environment. Copyright © 2015 Elsevier B.V. All rights reserved.

Petrophysical evaluation of the hydrocarbon potential of the Lower Cretaceous Kharita clastics, North Qarun oil field, Western Desert, Egypt

NASA Astrophysics Data System (ADS)

Teama, Mostafa A.; Nabawy, Bassem S.

2016-09-01

Based on the available well log data of six wells chosen in the North Qarun oil field in the Western Desert of Egypt, the petrophysical evaluation for the Lower Cretaceous Kharita Formation was accomplished. The lithology of Kharita Formation was analyzed using the neutron porosity-density and the neutron porosity-gamma ray crossplots as well as the litho-saturation plot. The petrophysical parameters, include shale volume, effective porosity, water saturation and hydrocarbon pore volume, were determined and traced laterally in the studied field through the iso-parametric maps. The lithology crossplots of the studied wells show that the sandstone is the main lithology of the Kharita Formation intercalated with some calcareous shale. The cutoff values of shale volume, porosity and water saturation for the productive hydrocarbon pay zones are defined to be 40%, 10% and 50%, respectively, which were determined, based on the applied crossplots approach and their limits. The iso-parametric contour maps for the average reservoir parameters; such as net-pay thickness, average porosity, shale volume, water saturation and the hydrocarbon pore volume were illustrated. From the present study, it is found that the Kharita Formation in the North Qarun oil field has promising reservoir characteristics, particularly in the northwestern part of the study area, which is considered as a prospective area for oil accumulation.

Challenge for Mesozoic hydrocarbon exploration in the Eastern Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdullah, S.; Rukmiati, M.G.; Sitompul, N.

1996-12-31

The eastern part of Indonesia covers approximately 3 million square kilometers, 35 percent being landmass and 65 percent covered by ocean. Only three of 38 sedimentary basins are producing hydrocarbon (Salawati, Bintuni, and Seram Basins). Oil and gas have discovered in the Lariang, Bone, Timor, Banggai, Sula and Biak Basins, however the discoveries have not developed yet. Hydrocarbon systems in Northern Australia and Papua New Guinea give the major contributions to the geological idea of Pre-Tertiary section in the less explored area in the Eastern Indonesia. The Triassic-Middle Jurassic marine carbonaceous shale sequences are the main hydrocarbon source rock inmore » the Irian Jaya and surrounding area (Buton, gula and Seram basins). The main Mesozoic reservoir are the Kembelangan Formation in the Bintuni Basin of Irian Jaya and Bobong Formation in the North Sula Region. Exploration play types in the Eastern Indonesia can be divided into five types: 1 - Peri Cratonic, 2 - Marginal Rift Graben, 3 - Thrust Fold Belt Island Arc, 4 - Early Collision and 5 -Microcontinental Block - Advanced Collision. Recent discoveries through Mesozoic section in Eastern Indonesia are: Roabiba-1 (1990) in Bintuni Basin-Irian Jaya (Kambelangan Formation); Loku- 1 (1990) in North Sula region (Pre-Tertiary sediments); Oseil-1 (1993/94) in Bula-Seram Basin (Jurassic Manusela Formation); Elang-1 (1 994); Kakaktua-1 (1994) and Laminaria-1 in North Bonaparte Basin (Upper Jurassic Sands).« less

Unstable ground in western North Dakota

USGS Publications Warehouse

Trimble, Donald E.

1979-01-01

Unstable ground in western North Dakota is mainly the result of mass-wasting processes. The units most affected are mudstones, siltstones, and sandstones of the Fort Union Formation. Ground instability generally is indicated by landslides, soil slides, or subsidence. Landslides are mostly of the slump-earthflow type and are localized along the flanks of the high buttes in southwestern North Dakota, including HT (Black) Butte, Chalky Buttes, Sentinel Butte, and East and West Rainy Buttes, and along parts of the valleys of the Des Lacs, Missouri, Little Missouri, and Heart Rivers. Landslides are sparse elsewhere. Soil slides are common in the areas south and southwest of the maximum position of the Pleistocene glacial ice margin on slopes of 15 degrees or more, and have taken place on some slopes as gentle as five degrees. The weathered, exposed surface of the Fort Union Formation seems to be especially susceptible to soil slides. Soil slides constitute the major type of ground instability in southwestern North Dakota. Subsidence is of two types: (1) subsidence over old underground mine workings, and (2) subsidence over naturally ignited and burned underground coal beds. Major subsidence has taken place over old, underground workings near Beulah, Wilton, Lehigh, Haynes, and Belfield, and lesser subsidence near Scranton, and west and north of Bowman. Thickness of overburden above the coal in all these areas is believed to be less than 30 m (100 ft). Subsidence has not taken place over old underground workings along the Des Lacs and-Souris valleys northwest of Minot, where the thickness of overburden is more than 60 m (200 ft). Spectacular subsidence has occurred over a burning underground coal bed at Burning Coal Vein Park near the Little Missouri River, northwest of Amidon.

Application of the Exergy UCG technology in international UCG projects

NASA Astrophysics Data System (ADS)

Blinderman, M. S.

2017-07-01

Underground Coal Gasification is a subject of continuing global interest in the energy sector. While the international scenario in UCG is promising, it is deeply desirable that advances in this area are seen in India as well. This is particularly so with the Paris Climate Agreement bringing in more stringent challenges for clean energy development. India has many potential coal basins which may be suitable for UCG deployment. India is in dire need of indigenous source of gaseous and liquid hydrocarbons that could compete with imported products. It is also the country with exceptionally large and diverse coal and lignite resources, large part of which could not be mined due to geological complexity and prohibitive cost. Thus, there is a rationale that the εUCG™ technology plays a decisive role in realizing the potential of Indian coal resources for the benefit of Indian industry and population. This article has been adapted by Dr. Ajay K. Singh from a lecture delivered at the “Workshop on Challenges and Opportunities of Underground Coal Gasification”, Vigyan Bhawan, New Delhi on 14 February 2017.

LOW TEMPERATURE FORMATION OF NITROGEN-SUBSTITUTED POLYCYCLIC AROMATIC HYDROCARBONS (PANHs)—BARRIERLESS ROUTES TO DIHYDRO(iso)QUINOLINES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, Dorian S. N.; Yang, Tao; Dangi, Beni B.

Meteorites contain bio-relevant molecules such as vitamins and nucleobases, which consist of aromatic structures with embedded nitrogen atoms. Questions remain over the chemical mechanisms responsible for the formation of nitrogen-substituted polycyclic aromatic hydrocarbons (PANHs) in extraterrestrial environments. By exploiting single collision conditions, we show that a radical mediated bimolecular collision between pyridyl radicals and 1,3-butadiene in the gas phase forms nitrogen-substituted polycyclic aromatic hydrocarbons (PANHs) 1,4-dihydroquinoline and to a minor amount 1,4-dihydroisoquinoline. The reaction proceeds through the formation of a van der Waals complex, which circumnavigates the entrance barrier implying it can operate at very low kinetic energy and thereforemore » at low temperatures of 10 K as present in cold molecular clouds such as TMC-1. The discovery of facile de facto barrierless exoergic reaction mechanisms leading to PANH formation could play an important role in providing a population of aromatic structures upon which further photo-processing of ice condensates could occur to form nucleobases.« less

Geothermal energy production with supercritical fluids

DOEpatents

Brown, Donald W.

2003-12-30

There has been invented a method for producing geothermal energy using supercritical fluids for creation of the underground reservoir, production of the geothermal energy, and for heat transport. Underground reservoirs are created by pumping a supercritical fluid such as carbon dioxide into a formation to fracture the rock. Once the reservoir is formed, the same supercritical fluid is allowed to heat up and expand, then is pumped out of the reservoir to transfer the heat to a surface power generating plant or other application.

Final report on Weeks Island Monitoring Phase : 1999 through 2004.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehgartner, Brian L.; Munson, Darrell Eugene

2005-05-01

This Final Report on the Monitoring Phase of the former Weeks Island Strategic Petroleum Reserve crude oil storage facility details the results of five years of monitoring of various surface accessible quantities at the decommissioned facility. The Weeks Island mine was authorized by the State of Louisiana as a Strategic Petroleum Reserve oil storage facility from 1979 until decommissioning of the facility in 1999. Discovery of a sinkhole over the facility in 1992 with freshwater inflow to the facility threatened the integrity of the oil storage and led to the decision to remove the oil, fill the chambers with brine,more » and decommission the facility. Thereafter, a monitoring phase, by agreement between the Department of Energy and the State, addressed facility stability and environmental concerns. Monitoring of the surface ground water and the brine of the underground chambers from the East Fill Hole produced no evidence of hydrocarbon contamination, which suggests that any unrecovered oil remaining in the underground chambers has been contained. Ever diminishing progression of the initial major sinkhole, and a subsequent minor sinkhole, with time was verification of the response of sinkholes to filling of the facility with brine. Brine filling of the facility ostensively eliminates any further growth or new formation from freshwater inflow. Continued monitoring of sinkhole response, together with continued surface surveillance for environmental problems, confirmed the intended results of brine pressurization. Surface subsidence measurements over the mine continued throughout the monitoring phase. And finally, the outward flow of brine was monitored as a measure of the creep closure of the mine chambers. Results of each of these monitoring activities are presented, with their correlation toward assuring the stability and environmental security of the decommissioned facility. The results suggest that the decommissioning was successful and no contamination of the surface environment by crude oil has been found.« less

Identification of persulfate oxidation products of polycyclic aromatic hydrocarbon during remediation of contaminated soil

EPA Science Inventory

The extent of PAH transformation, the formation and transformation of reaction byproducts during persulfate oxidation of polycyclic aromatic hydrocarbons (PAHs) in coking plant soil was investigated. Pre-oxidation analyses indicated that oxygen-containing PAHs (oxy-PAHs) existed ...

The Certification Framework: Risk Assessment for Safety and Effectiveness of Geologic Carbon Sequestration

NASA Astrophysics Data System (ADS)

Oldenburg, C. M.; Nicot, J.; Bryant, S. L.

2008-12-01

Motivated by the dual objectives of (1) encouraging geologic carbon sequestration (GCS) as one of several strategies urgently needed to reduce CO2 emissions, and (2) protecting the environment from unintended CO2 injection-related impacts, we have developed a simple and transparent framework for certifying GCS safety and effectiveness at individual sites. The approach we developed, called the Certification Framework (CF), is proposed as a standard way for project proponents, regulators, and the public to analyze and understand risks and uncertainties of GCS. In the CF, we relate effective trapping to CO2 leakage risk, where we use the standard definition of risk involving the two factors (1) probability of a particular leakage scenario, and (2) impact of that leakage scenario. In short, if the CO2 leakage risk as calculated by the CF is below threshold values for the life of the project, then effective trapping is predicted and the site can be certified. The concept of effective trapping is more general than traditional "no migration" approaches to underground injection regulation. We achieve simplicity in the CF by using (1) wells and faults as the potential leakage pathways, (2) five compartments to represent where impacts can occur (underground sources of drinking water, hydrocarbon and mineral resources, near-surface environment, health and safety, and emission credits and atmosphere), (3) modeled CO2 fluxes and concentrations as proxies for impact to compartments, (4) broad ranges of storage formation properties to generate a catalog of simulated CO2 plumes, and (5) probabilities of intersection of the CO2 plume with the conduits and compartments. In a case study application of the CF for a saline formation GCS site in the Texas Gulf Coast, analysis with the CF suggested the overall leakage risk to be very small, with the largest contribution coming from risk to the near-surface environment due to potential leakage up abandoned wells, depending on the effective permeability assumed for the wells. This result shows that risk could be drastically reduced by locating and monitoring abandoned wells, along with well or leakage mitigation if necessary. By this means, effective trapping can be predicted with greater certainty because both factors of risk (probability of well leakage, and impact of well leakage) can be reduced significantly through surface monitoring and mitigation, if needed.

Method and apparatus for production of subsea hydrocarbon formations

DOEpatents

Blandford, Joseph W.

1994-01-01

A well tender system for controlling, separating, storing and offloading well fluids produced from subsea hydrocarbon formations. The system comprises a vertically aligned series of tethered cylindrical tanks which are torsionally stabilized by flexible catenary production riser and export riser bundles, and serviced by separate catenary pipe bundles. Piles are secured to the seabed, each pile assembly being pivotally connected to a lower rigid tendon, which is in turn connected to tendons arranged about the periphery of the interconnected cylindrical tanks.

Method and apparatus for production of subsea hydrocarbon formations

DOEpatents

Blandford, Joseph W.

1992-01-01

A well tender system for controlling, separating, storing and offloading well fluids produced from subsea hydrocarbon formations. The system comprises a vertically aligned series of tethered cylindrical tanks which are torsionally stabilized by flexible catenary production riser and expert riser bundles, and serviced by separate catenary pipe bundles. Piles are secured to the seabed, each pile assembly being pivotally connected to a lower rigid tendon, which is in turn connected to tendons arranged about the periphery of the interconnected cylindrical tanks.

Raney Ni-Sn catalyst for H2 production from biomass-derived hydrocarbons.

PubMed

Huber, G W; Shabaker, J W; Dumesic, J A

2003-06-27

Hydrogen (H2) was produced by aqueous-phase reforming of biomass-derived oxygenated hydrocarbons at temperatures near 500 kelvin over a tin-promoted Raney-nickel catalyst. The performance of this non-precious metal catalyst compares favorably with that of platinum-based catalysts for production of hydrogen from ethylene glycol, glycerol, and sorbitol. The addition of tin to nickel decreases the rate of methane formation from C-O bond cleavage while maintaining the high rates of C-C bond cleavage required for hydrogen formation.

Noncatalytic oxypyrolysis of C{sub 2+}-hydrocarbons from natural gas to ethylene and propylene in a most energy-efficient and safe manner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhary, V.R.; Mulla, S.A.R.; Rajput, A.M.

1997-06-01

Noncatalytic oxypyrolysis of C{sub 2+}-hydrocarbons from natural gas at 700--850 C in the presence of steam and limited oxygen yields ethylene and propylene with appreciable conversion and high selectivity but with almost no coke or tarlike product formation. In this process, the exothermic oxidative hydrocarbon conversion reactions are coupled directly with the endothermic cracking of C{sub 2+}-hydrocarbons by their simultaneous occurrence. Hence, the process operates in a most energy-efficient and safe (or nonhazardous) manner and also can be made almost thermoneutral or mildly endothermic/exothermic, thus requiring little or no external energy for the hydrocarbon conversion reactions.

Relevance and Significance of Extraterrestrial Abiological Hydrocarbon Chemistry.

PubMed

Olah, George A; Mathew, Thomas; Prakash, G K Surya

2016-06-08

Astrophysical observations show similarity of observed abiological "organics"-i.e., hydrocarbons, their derivatives, and ions (carbocations and carbanions)-with studied terrestrial chemistry. Their formation pathways, their related extraterrestrial hydrocarbon chemistry originating from carbon and other elements after the Big Bang, their parent hydrocarbon and derivative (methane and methanol, respectively), and transportation of derived building blocks of life by meteorites or comets to planet Earth are discussed in this Perspective. Their subsequent evolution on Earth under favorable "Goldilocks" conditions led to more complex molecules and biological systems, and eventually to humans. The relevance and significance of extraterrestrial hydrocarbon chemistry to the limits of science in relation to the physical aspects of evolution on our planet Earth are also discussed.

Biological markers from Green River kerogen decomposition

NASA Astrophysics Data System (ADS)

Burnham, A. K.; Clarkson, J. E.; Singleton, M. F.; Wong, C. M.; Crawford, R. W.

1982-07-01

Isoprenoid and other carbon skeletons that are formed in living organisms and preserved essentially intact in ancient sediments are often called biological markers. The purpose of this paper is to develop improved methods of using isoprenoid hydrocarbons to relate petroleum or shale oil to its source rock. It is demonstrated that most, but not all, of the isoprenoid hydrocarbon structures are chemically bonded in kerogen (or to minerals) in Green River oil shale. The rate constant for thermally producing isoprenoid, cyclic, and aromatic hydrocarbons is substantially greater than for the bulk of shale oil. This may be related to the substantial quantity of CO 2 which is evolved coincident with the isoprenoid hydrocarbons but prior to substantial oil evolution. Although formation of isoprenoid alkenes is enhanced by rapid heating and high pyrolysis temperatures, the ratio of isoprenoid alkenes plus alkanes to normal alkenes plus alkanes is independent of heating rate. High-temperature laboratory pyrolysis experiments can thus be used to predict the distribution of aliphatic hydrocarbons in low temperature processes such as in situ shale oil production and perhaps petroleum formation. Finally, we demonstrate that significant variation in biological marker ratios occurs as a function of stratigraphy in the Green River formation. This information, combined with methods for measuring process yield from oil composition, enables one to relate time-dependent processing conditions to the corresponding time-dependent oil yield in a vertical modified- in situ retort even if there is a substantial and previously undetermined delay in drainage of shale oil from the retort.

A fast complex domain-matching pursuit algorithm and its application to deep-water gas reservoir detection

NASA Astrophysics Data System (ADS)

Zeng, Jing; Huang, Handong; Li, Huijie; Miao, Yuxin; Wen, Junxiang; Zhou, Fei

2017-12-01

The main emphasis of exploration and development is shifting from simple structural reservoirs to complex reservoirs, which all have the characteristics of complex structure, thin reservoir thickness and large buried depth. Faced with these complex geological features, hydrocarbon detection technology is a direct indication of changes in hydrocarbon reservoirs and a good approach for delimiting the distribution of underground reservoirs. It is common to utilize the time-frequency (TF) features of seismic data in detecting hydrocarbon reservoirs. Therefore, we research the complex domain-matching pursuit (CDMP) method and propose some improvements. First is the introduction of a scale parameter, which corrects the defect that atomic waveforms only change with the frequency parameter. Its introduction not only decomposes seismic signal with high accuracy and high efficiency but also reduces iterations. We also integrate jumping search with ergodic search to improve computational efficiency while maintaining the reasonable accuracy. Then we combine the improved CDMP with the Wigner-Ville distribution to obtain a high-resolution TF spectrum. A one-dimensional modeling experiment has proved the validity of our method. Basing on the low-frequency domain reflection coefficient in fluid-saturated porous media, we finally get an approximation formula for the mobility attributes of reservoir fluid. This approximation formula is used as a hydrocarbon identification factor to predict deep-water gas-bearing sand of the M oil field in the South China Sea. The results are consistent with the actual well test results and our method can help inform the future exploration of deep-water gas reservoirs.

Emissions of Methane and Other Hydrocarbons Due to Wellbore Leaks

NASA Astrophysics Data System (ADS)

Lyman, S. N.; Mansfield, M. L.

2013-12-01

The explosive growth of oil and gas production in the United States has focused public and regulatory attention on environmental impacts of hydrocarbon extraction, including air quality and climate impacts. However, EPA and others have acknowledged that current air emissions factors and inventories for many oil and gas-related source categories are inadequate or lacking entirely. One potentially important emissions source is leakage of natural gas from wellbores. This phenomenon has long been recognized to occur, but no attempt has been made to quantify emission rates of gas leaked from wellbores to the atmosphere. Soil gas measurements carried out by USGS over the last several years in Utah's oil and gas fields have shown that, while concentrations of methane in soils near many wells are low, soil gas near some wells can contain more than 10% methane, indicating that underground leakage is occurring. In summer 2013 we carried out a campaign to measure the emission rate of methane and other hydrocarbons from soils near wells in two oil and gas fields in Utah. We measured emissions from several locations on some well pads to determine the change in emission rate with distance from well heads, and we measured at non-well sites in the same fields to determine background emission rates. Methane emission rates at some wells exceeded 3 g m-2 h-1, while emission rates at other wells were similar to background levels, and a correlation was observed between soil gas methane concentrations and methane emission rates from the soil. We used these data to estimate total methane and hydrocarbon emission rates from these two fields.

Formation of hydrocarbons under upper mantle conditions: experimental view

NASA Astrophysics Data System (ADS)

Kolesnikov, Anton; Kutcherov, Vladimir G.

2010-05-01

Main postulates of the theory of abiogenic abyssal origin of petroleum have been developed in the last 50 years in Russia and Ukraine. According to this theory, hydrocarbon compounds were generated in the mantle and migrated through the deep faults into the Earth's crust. There they formed oil and gas deposits in any kinds of rocks and in any kind of their structural positions. Until recently the main obstacle to accept the theory was the lack of reliable and reproducible experimental data confirming the possibility of the synthesis of complex hydrocarbon systems under the mantle conditions. The results received in the last decade by different groups of researchers from Russia, U.S.A. and China have confirmed the possibility of generation of hydrocarbons from inorganic materials, highly distributed in the Earth's mantle, under thermobaric conditions of 70-250 km: 2 - 5 GPa and 1000-1500 K. Experiments made in the CONAC chamber at pressures of 3-5 GPa and temperatures of 1000-1500 K by Kutcherov et al. [1, 2] have demonstrated that the mixtures of hydrocarbons with composition similar to natural hydrocarbon systems have been received as a result of chemical reactions between CaCO3, FeO and H2O. Methane formation from the same compounds was registered after heating up to 600-1500 K at pressures of 4-11 GPa in diamond anvil cells [4, 5, 6]. Influence of oxidation state of carbon donor and cooling rate of the fluid synthesized at high pressure were studied using different types of high pressure equipments. It was shown that composition of the final hydrocarbon mixture depends on these parameters. Experimental investigations of transformation of methane and ethane at 2-5 GPa and 1000-1500 K [3] confirmed thermodynamic stability of heavy hydrocarbons in the upper mantle and showed the possibility of hydrocarbon chain growth even at oxidative environment. For development of the theory of abiogenic abyssal origin of petroleum it is necessary to arrange a set of new experiments to understand the pathways of hydrocarbons formation, influence of pressure, temperature, oxygen fugacity and chemical composition of the environment on the content of the mantle fluid. [1] Kutcherov, V. G., Bendeliani, N. A. Alekseev, V. A. & Kenney, J. F. Synthesis of Hydrocarbons from Minerals at Pressures up to 5 GPa. Doklady Physical Chemistry, 387, 4-6, 328-330 (2002). [2] Kenney, J. F., Kutcherov, V. G., Bendeliani, N. A. & Alekseev, V. A. The Evolution of Multicomponent Systems at High Pressures: VI. The Thermodynamic Stability of the Hydrogen-Carbon System: The Genesis of Hydrocarbons and the Origin of Petroleum. Proc. Natl. Acad. Sci. U.S.A., 99, 10976-10981 (2002). [3] Kolesnikov A., Kutcherov V. G. and Goncharov A. F. Methane-derived hydrocarbons produced under upper-mantle conditions. Nature Geoscience, 2, 566 - 570 (2009). [4] Scott H.P., Hemley R.J, Mao H. et al. Generation of methane in the Earth's mantle: In situ high pressure-temperature measurements of carbonate reduction, Proc. Natl. Acad. Sci. U.S.A., 101 14023-14026 (2004). [5] Chen J.Y., et al. Methane formation from CaCO3 reduction catalyzed by high pressure. Chin. Chem. Lett., 19, 4, 475-478 (2008). [6] Sharma A., Cody G. D., and Hemley R. J. In situ Diamond-anvil cell observations of methanogenesis at high pressures and temperatures. Energy Fuels, 23, 11, 5571-5579 (2009).

The Science of the Deep Underground Neutrino Experiment (DUNE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This 4-minute animation shows how the international Deep Underground Neutrino Experiment will help scientists understand how the universe works. DUNE will use a huge particle detector a mile underground to embark on a mission with three major science goals: 1.) Study an intense, 1,300-kilometer-long neutrino beam to discover what happened after the big bang: Are neutrinos the reason the universe is made of matter? 2.) Use 70,000 tons of liquid argon to look for proton decay and move closer to realizing Einstein’s dream of a unified theory of matter and energy. 3.) Catch neutrinos from a supernova to watch themore » formation of neutron stars and black holes in real time. About 1,000 scientists from 160 institutions in 30 countries are working on the Deep Underground Neutrino Experiment, hosted at the Department of Energy’s Fermi National Accelerator Laboratory and South Dakota’s Sanford Underground Research Facility. DUNE collaborators come from institutions in Armenia, Brazil, Bulgaria, Canada, Chile, China, Colombia, Czech Republic, Finland, France, Greece, India, Iran, Italy, Japan, Madagascar, Mexico, Netherlands, Peru, Poland, Romania, Russia, South Korea, Spain, Sweden, Switzerland, Turkey, Ukraine, United Kingdom, and the United States of America.« less

The Influence of the Ufimian Tectonic Concentric Structure on the Hydrocarbon Migration and Ore Genesis

NASA Astrophysics Data System (ADS)

Filippov, V. A.

2018-01-01

The Ufimian tectonic concentric structure (UTC) is a regional structure with concentric and zonal structure of the internal gravity field. In the Neoproterozoic this structure was at higher hypsometric level relative to the Bashkir Meganticlinorium. The most significant uplift of this tectonic concentric structure happened at the beginning of the Karatau time ( 825 Ma) and was accompanied by the formation of a ring fractured zone, favorable for hydrocarbon migration from the Lower Riphean black shales. Due to this, bitumens with higher Mo content in the Neoproterozoic and Paleozoic deposits are confined spatially to this zone. The bitumenosity of the Neoproterozoic deposits on the southern slope of the Ufimian tectonic concentric structure could have contributed to the formation of complex Cu-Ag-Mo-Re ores (copper sands) at the upper boundary of terrigenous red deposits of the Zilmerdak Formation. Positive structures identified in the Neoproterozoic deposits near the margin of the Ufimian tectonic concentric structure are considered to be promising for searching for hydrocarbon fields.

Effect of petroleum-related pollutants on Aurelia growth and development. Progress report, September 12, 1977--November 15, 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spangenberg, D.B.

Strobilation initiation studies revealed that phenol and aniline inhibited strobilation initiation and phenol (at lower dosages) caused a reversal of strobilation initiation whereas benzo(a)pyrene did not affect this process. Ephyra abnormalities were created by phenol (abnormal pulsing and a cup-shaped morphology) naphthalene (abnormal lappet formation) and aniline (impaired nematocyst synthesis). Statolith synthesis was reduced by aniline, naphthalene, phenol, and benzo(a)pyrene. Budding rates were likewise retarded by phenol and aniline as was the metamorphosis of planulae into polyps. Tentacle regeneration of mature polyps was not affected by phenol or aniline. A specific testing procedure for the administration of the water insolublemore » hydrocarbons was developed using sonication. The hydrocarbons were reduced to very fine particles with sonication and the minute particles were taken into the jellyfish. New jellyfish cultures were developed from medusae collected in Norfolk. These organisms responded to iodide, thyroxine, and hydrocarbons in a similar manner as the Texas Aurelia. The hydrocarbon effects on strobilation initiation and ephyra formation suggested that the hydrocarbons affected thyroxine synthesis and/or action in the jellyfish (and other organisms) and call for detailed studies as to their specific mechanisms of action.« less

Process for improving the energy density of feedstocks using formate salts

DOEpatents

Wheeler, Marshall Clayton; van Heiningen, Adriaan R.P.; Case, Paige A.

2015-09-01

Methods of forming liquid hydrocarbons through thermal deoxygenation of cellulosic compounds are disclosed. Aspects cover methods including the steps of mixing a levulinic acid salt-containing feedstock with a formic acid salt, exposing the mixture to a high temperature condition to form hydrocarbon vapor, and condensing the hydrocarbon vapor to form liquid hydrocarbons, where both the formic acid salt and the levulinic acid salt-containing feedstock decompose at the high temperature condition and wherein one or more of the mixing, exposing, and condensing steps is carried out a pressure between about vacuum and about 10 bar.

Experimental Assessment of Carbon Isotopes of Light Hydrocarbons under Different Redox Conditions

NASA Astrophysics Data System (ADS)

Fu, Q.; Chen, X.

2017-12-01

Hydrocarbons can be derived from a variety of carbon sources, by different processes, and under a wide range of physicochemical conditions. Other than bacterial activities facilitating biogenic hydrocarbon formation at low temperatures, decomposition of complex organic matter in sedimentary rocks at elevated temperatures produce thermogenic hydrocarbons, whereas abiogenic hydrocarbons are mainly generated through Fischer-Tropsch type synthesis with mineral catalysts. The carbon isotope has been used extensively to distinguish hydrocarbons of different origins and their formation conditions. For each type of hydrocarbons, however, environmental conditions may change reaction pathways and corresponding isotope fractionations. To better understand the variation of carbon isotopes caused by environmental variables, mineral constraints in particular, a series of laboratory experiments are conducted. In experiments where thermogenic hydrocarbons are formed, oil shale is the source material with different gypsum contents (0, 0.3, 0.5, and 1 wt.%). The abundance of generated light straight chain hydrocarbons decreases with increasing gypsum content, but their carbon isotopes become heavier. For example, the δ13C value of methane increases from -55.1‰ to -41.4‰ with gypsum varying between 0 and 1 wt.%. In similar experiments with the presence of MnO2, carbon isotope values of light alkanes are also higher, but with limited magnitudes (e.g., 3 to 4‰ for methane). In another experiment with dissolved H2 gas of 100 mmol/kg, light alkanes become depleted in 13C than experiments without H2. For example, there is a depletion of 2.7‰ for methane. The variation of carbon isotope values of light alkanes suggests the redox condition, constrained by mineral assemblage, fluid composition, and physical environment, play an important role in isotope fractionation. The pathway of hydrocarbon generation may be different under oxidized or reducing conditions. A set of experiments, in which abiogenic hydrocarbons are formed, is currently in progress. Combined together, they would facilitate our understanding of carbon isotope fractionation under geological conditions, and effective use of carbon isotopes as a diagnostic tool for hydrocarbons that are poorly understood in terms of origin and evolution.

Modeling the Role of Alkanes, Polycyclic Aromatic Hydrocarbons, and Their Oligomers in Secondary Organic Aerosol Formation

EPA Science Inventory

A computationally efficient method to treat secondary organic aerosol (SOA) from various length and structure alkanes as well as SOA from polycyclic aromatic hydrocarbons (PAHs) is implemented in the Community Multiscale Air Quality (CMAQ) model to predict aerosol concentrations ...

Studying of shale organic matter structure and pore space transformations during hydrocarbon generation

NASA Astrophysics Data System (ADS)

Giliazetdinova, Dina; Korost, Dmitry; Gerke, Kirill

2016-04-01

Due to the increased interest in the study of the structure, composition, and oil and gas potential of unconventional hydrocarbon resources, investigations of the transformation of the pore space of rocks and organic matter alterations during the generation of hydrocarbon fluids are getting attention again. Due to the conventional hydrocarbon resources decreasing, there will be a necessity to develop new unconventional hydrocarbon resources. Study of the conditions and processes of hydrocarbon generation, formation and transformation of the pore space in these rocks is pivotal to understand the mechanisms of oil formation and determine the optimal and cost effective ways for their industrial exploration. In this study, we focus on organic matter structure and its interaction with the pore space of shales during hydrocarbon generation and report some new results. Collected rock samples from Domanic horizon of South-Tatar arch were heated in the pyrolyzer to temperatures closely corresponding to different catagenesis stages. X-ray microtomography method and SEM were used to monitor changes in the morphology of the pore space and organic matter structure within studied shale rocks. By routine measurements we made sure that all samples (10 in total) had similar composition of organic and mineral phases. All samples in the collection were grouped according to initial structure and amount of organics and processed separately to: 1) study the influence of organic matter content on the changing morphology of the rock under thermal effects; 2) study the effect of initial structure on the primary migration processes for samples with similar organic matter content. An additional experiment was conducted to study the dynamics of changes in the structure of the pore space and prove the validity of our approach. At each stage of heating the morphology of altered rocks was characterized by formation of new pores and channels connecting primary voids. However, it was noted that the samples with a relatively low content of the organic matter had less changes in pore space morphology, in contrast to rocks with a high organic content. Second part of the study also revealed significant differences in resulting pore structures depending on initial structure of the unaltered rocks and connectivity of original organics. Significant changes in the structure of the pore space were observed during the sequential heating in the range from 260 C to 430 C, which corresponds to the most intense stage of the hydrocarbons formation. This work was partially supported by RSF grant 14-17-00658.

Hyperspectral Geobotanical Remote Sensing for Monitoring and Verifying CO 2 Containment Final Report CRADA No. TC-2036-02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickles, W. L.; Ebrom, D. A.

This collaborative effort was in support of the CO 2 Capture Project (CCP), to develop techniques that integrate overhead images of plant species, plant health, geological formations, soil types, aquatic, and human use spatial patterns for detection and discrimination of any CO 2 releases from underground storage formations. The goal of this work was to demonstrate advanced hyperspectral geobotanical remote sensing methods to assess potential leakage of CO 2 from underground storage. The timeframes and scales relevant to the long-term storage of CO 2 in the subsurface make remote sensing methods attractive. Moreover, it has been shown that individual fieldmore » measurements of gas composition are subject to variability on extremely small temporal and spatial scales. The ability to verify ultimate reservoir integrity and to place individual surface measurements into context will be crucial to successful long-term monitoring and verification activities. The desired results were to produce a defined and tested procedure that could be easily used for long-term monitoring of possible CO 2 leakage from underground CO 2 sequestration sites. This testing standard will be utilized on behalf of the oil industry.« less

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

The genetic source and timing of hydrocarbon formation in gas hydrate reservoirs in Green Canyon, Block GC955

NASA Astrophysics Data System (ADS)

Moore, M. T.; Darrah, T.; Cook, A.; Sawyer, D.; Phillips, S.; Whyte, C. J.; Lary, B. A.

2017-12-01

Although large volumes of gas hydrates are known to exist along continental slopes and below permafrost, their role in the energy sector and the global carbon cycle remains uncertain. Investigations regarding the genetic source(s) (i.e., biogenic, thermogenic, mixed sources of hydrocarbon gases), the location of hydrocarbon generation, (whether hydrocarbons formed within the current reservoir formations or underwent migration), rates of clathrate formation, and the timing of natural gas formation/accumulation within clathrates are vital to evaluate economic potential and enhance our understanding of geologic processes. Previous studies addressed some of these questions through analysis of conventional hydrocarbon molecular (C1/C2+) and stable isotopic (e.g., δ13C-CH4, δ2H-CH4, δ13C-CO2) composition of gases, water chemistry and isotopes (e.g., major and trace elements, δ2H-H2O, δ18O-H2O), and dissolved inorganic carbon (δ13C-DIC) of natural gas hydrate systems to determine proportions of biogenic and thermogenic gas. However, the effects from contributions of mixing, transport/migration, methanogenesis, and oxidation in the subsurface can complicate the first-order application of these techniques. Because the original noble gas composition of a fluid is preserved independent of microbial activity, chemical reactions, or changes in oxygen fugacity, the integration of noble gas data can provide both a geochemical fingerprint for sources of fluids and an additional insight as to the uncertainty between effects of mixing versus post-genetic modification. Here, we integrate inert noble gases (He, Ne, Ar, and associated isotopes) with these conventional approaches to better constrain the source of gas hydrate formation and the residence time of fluids (porewaters and natural gases) using radiogenic 4He ingrowth techniques in cores from two boreholes collected as part of the University of Texas led UT-GOM2-01 drilling project. Pressurized cores were extracted from coarse silt/sand reservoirs 600 m below the seafloor within the GC955 block of the Green Canyon protraction area at the edge of the Sigsbee escarpment. Preliminary results suggest that hydrocarbons gases from this study area are dominantly formed by biogenic processes with residence time estimates ranging from 6.2-49.8 kyr.

Geochemical evaluation of upper cretaceous fruitland formation coals, San Juan Basin, New Mexico and Colorado

USGS Publications Warehouse

Michael, G.E.; Anders, D.E.; Law, B.E.

1993-01-01

Geochemical analyses of coal samples from the Upper Cretaceous Fruitland Formation in the San Juan Basin of New Mexico and Colorado were used to determine thermal maturity, type of kerogen, and hydrocarbon generation potential. Mean random vitrinite reflectance (%Rm) of the Fruitland coal ranges from 0.42 to 1.54%. Rock-Eval pyrolysis data and saturated to aromatic hydrocarbon ratio indicate that the onset of thermal hydrocarbon generation begins at about 0.60% Rm and peak generation occurs at about 0.85% Rm. Several samples have hydrogen index values between 200 and 400, indicating some potential for liquid hydrocarbon generation and a mixed Type III and II kerogen. Pentacyclic and tricyclic terpanes, steranes, aromatic steroids and methylphenanthrene maturity parameters were observed through the complete range of thermal maturity in the Fruitland coals. Aromatic pentacyclic terpanes, similar to those found in brown coals of Australia, were observed in low maturity samples, but not found above 0.80% Rm. N-alkane depleted coal samples, which occur at a thermal maturity of approx. 0.90% Rm, paralleling peak hydrocarbon generation, are fairly widespread throughout the basin. Depletion of n-alkanes in these samples may be due to gas solution stripping and migration fromthe coal seams coincident with the development of pressure induced fracturing due to hydrocarbon generation; however, biodegradation may also effect these samples. ?? 1993.

Power systems utilizing the heat of produced formation fluid

DOEpatents

Lambirth, Gene Richard [Houston, TX

2011-01-11

Systems, methods, and heaters for treating a subsurface formation are described herein. At least one method includes treating a hydrocarbon containing formation. The method may include providing heat to the formation; producing heated fluid from the formation; and generating electricity from at least a portion of the heated fluid using a Kalina cycle.

Potential for deep basin-centered gas accumulation in Travis Peak (Hosston) Formation, Gulf Coastal Basin

USGS Publications Warehouse

Bartberger, Charles E.; Dyman, Thaddeus S.; Condon, Steven M.

2003-01-01

The potential of Lower Cretaceous sandstones of the Travis Peak Formation in the northern Gulf Coast Basin to harbor a basin-centered gas accumulation was evaluated by examining (1) the depositional and diagenetic history and reservoir properties of Travis Peak sandstones, (2) the presence and quality of source rocks for generating gas, (3) the burial and thermal history of source rocks and time of gas generation and migration relative to tectonic development of Travis Peak traps, (4) gas and water recoveries from drill-stem and formation tests, (5) the distribution of abnormal pressures based on shut-in-pressure data, and (6) the presence or absence of gas-water contacts associated with gas accumulations in Travis Peak sandstones. The Travis Peak Formation (and correlative Hosston Formation) is a basinward-thickening wedge of terrigenous clastic sedimentary rocks that underlies the northern Gulf Coast Basin from eastern Texas across northern Louisiana to southern Mississippi. Clastic infl ux was focused in two main fl uvial-deltaic depocenters?one located in northeastern Texas and the other in southeastern Mississippi and northeastern Louisiana. Across the main hydrocarbon-productive trend in eastern Texas and northern Louisiana, the Travis Peak Formation is about 2,000 ft thick. Most Travis Peak hydrocarbon production in eastern Texas comes from drilling depths between 6,000 and 10,000 ft. Signifi cant decrease in porosity and permeability occurs through that depth interval. Above 8,000-ft drilling depth in eastern Texas, Travis Peak sandstone matrix permeabilities often are signifi cantly higher than the 0.1-millidarcy (mD) cutoff that characterizes tight-gas reservoirs. Below 8,000 ft, matrix permeability of Travis Peak sandstones is low because of pervasive quartz cementation, but abundant natural fractures impart signifi cant fracture permeability. Although pressure data within the middle and lower Travis Peak Formation are limited in eastern Texas, overpressured reservoirs caused by thermal generation of gas, typical of basin-centered gas accumulations, are not common in the Travis Peak Formation. Signifi cant overpressure was found in only one Travis Peak sandstone reservoir in 1 of 24 oil and gas fi elds examined across eastern Texas and northern Louisiana. The presence of gas-water contacts is perhaps the most defi nitive criterion indicating that a gas accumulation is conventional rather than a ?sweet spot? within a basin-centered gas accumulation. Hydrocarbon-water contacts within Travis Peak sandstone reservoirs were documented in 17 fi elds and probably occur in considerably more fi elds across the productive Travis Peak trend in eastern Texas and northern Louisiana. All known hydrocarbon-water contacts in Travis Peak reservoirs in eastern Texas, however, occur within sandstones in the upper 500 ft of the formation. Although no gas-water contacts have been reported within the lower three-fourths of the Travis Peak Formation in northeastern Texas, gas production from that interval is limited. The best available data suggest that most middle and lower Travis Peak sandstones are water bearing in northeastern Texas. Insuffi cient hydrocarbon charge relative to permeability of Travis Peak reservoirs might be responsible for lack of overpressure and basin-centered gas within the Travis Peak Formation. Shales interbedded with Travis Peak sandstones in eastern Texas are primarily oxidized fl ood-plain deposits with insuffi cient organic-carbon content to be signifi cant sources of oil and gas. The most likely source rocks for hydrocarbons in Travis Peak reservoirs are two stratigraphically lower units, the Jurassic-age Bossier Shale of the Cotton Valley Group, and laminated, lime mudstones of the Jurassic Smackover Formation. Hydrocarbon charge, therefore, might be suffi cient for development of conventional gas accumulations, but it is insuffi cient for

Hydrocarbon Source Rocks in the Deep River and Dan River Triassic Basins, North Carolina

USGS Publications Warehouse

Reid, Jeffrey C.; Milici, Robert C.

2008-01-01

This report presents an interpretation of the hydrocarbon source rock potential of the Triassic sedimentary rocks of the Deep River and Dan River basins, North Carolina, based on previously unpublished organic geochemistry data. The organic geochemical data, 87 samples from 28 drill holes, are from the Sanford sub-basin (Cumnock Formation) of the Deep River basin, and from the Dan River basin (Cow Branch Formation). The available organic geochemical data are biased, however, because many of the samples collected for analyses by industry were from drill holes that contained intrusive diabase dikes, sills, and sheets of early Mesozoic age. These intrusive rocks heated and metamorphosed the surrounding sediments and organic matter in the black shale and coal bed source rocks and, thus, masked the source rock potential that they would have had in an unaltered state. In places, heat from the intrusives generated over-mature vitrinite reflectance (%Ro) profiles and metamorphosed the coals to semi-anthracite, anthracite, and coke. The maximum burial depth of these coal beds is unknown, and depth of burial may also have contributed to elevated thermal maturation profiles. The organic geochemistry data show that potential source rocks exist in the Sanford sub-basin and Dan River basin and that the sediments are gas prone rather than oil prone, although both types of hydrocarbons were generated. Total organic carbon (TOC) data for 56 of the samples are greater than the conservative 1.4% TOC threshold necessary for hydrocarbon expulsion. Both the Cow Branch Formation (Dan River basin) and the Cumnock Formation (Deep River basin, Sanford sub-basin) contain potential source rocks for oil, but they are more likely to have yielded natural gas. The organic material in these formations was derived primarily from terrestrial Type III woody (coaly) material and secondarily from lacustrine Type I (algal) material. Both the thermal alteration index (TAI) and vitrinite reflectance data (%Ro) indicate levels of thermal maturity suitable for generation of hydrocarbons. The genetic potential of the source rocks in these Triassic basins is moderate to high and many source rock sections have at least some potential for hydrocarbon generation. Some data for the Cumnock Formation indicate a considerably higher source rock potential than the basin average, with S1 + S2 data in the mid-20 mg HC/g sample range, and some hydrocarbons have been generated. This implies that the genetic potential for all of these strata may have been higher prior to the igneous activity. However, the intergranular porosity and permeability of the Triassic strata are low, which makes fractured reservoirs more attractive as drilling targets. In some places, gravity and magnetic surveys that are used to locate buried intrusive rock may identify local thermal sources that have facilitated gas generation. Alternatively, awareness of the distribution of large intrusive igneous bodies at depth may direct exploration into other areas, where thermal maturation is less than the limits of hydrocarbon destruction. Areas prospective for natural gas also contain large surficial clay resources and any gas discovered could be used as fuel for local industries that produce clay products (principally brick), as well as fuel for other local industries.

Hydrocarbon saturation determination using acoustic velocities obtained through casing

DOEpatents

Moos, Daniel

2010-03-09

Compressional and shear velocities of earth formations are measured through casing. The determined compressional and shear velocities are used in a two component mixing model to provides improved quantitative values for the solid, the dry frame, and the pore compressibility. These are used in determination of hydrocarbon saturation.

Simultaneous Production of Reduced Nitrogen Compounds and Hydrocarbons Using Amorphous Iron Silicate Smokes as a Catalyst

NASA Technical Reports Server (NTRS)

Nuth, Joseph A., III; Hill, Hugh G. M.

2001-01-01

Amorphous iron silicates efficiently catalyze formation of hydrocarbons and ammonia under conditions similar to that found in the solar nebula. Preliminary data and rates will be discussed, and much further experimentation is required. Additional information is contained in the original extended abstract.

Knowledge and the Experience of Women Living Underground during the Portuguese Dictatorship

ERIC Educational Resources Information Center

Nogueira, Cristina Marques

2015-01-01

This paper assumes that formative processes are not limited to the school context or model but that other life contexts and experiences, even if not intentionally, have educational effects. These informal formative contexts and experiences can play a key role individual´s development, resulting not only in superficial changes, but also in deep…

Petroleum systems and geologic assessment of undiscovered oil and gas, Cotton Valley group and Travis Peak-Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces of the northern Gulf Coast region. Chapters 1-7.

USGS Publications Warehouse

,

2006-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cotton Valley Group and Travis Peak and Hosston Formations in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces in the Gulf Coast Region (USGS Provinces 5048 and 5049). The Cotton Valley Group and Travis Peak and Hosston Formations are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and eight assessment units. Seven assessment units were quantitatively assessed for undiscovered oil and gas resources.

Spatially selective formation of hydrocarbon, fluorocarbon, and hydroxyl-terminated monolayers on a microelectrode array.

PubMed

Cook, Kevin M; Nissley, Daniel A; Ferguson, Gregory S

2013-06-11

A protection-deprotection strategy, using gold oxide as a passivating layer, was used to direct the self-assembly of monolayers (SAMs) selectively at individual gold microelectrodes in an array. This approach allowed the formation of hydroxyl-terminated monolayers, without side reactions, in addition to hydrocarbon and fluorocarbon SAMs. Fluorescence microscopy was used to visualize selective dewetting of hydrophobic monolayers by an aqueous dye solution, and spatially resolved X-ray photoelectron spectroscopy was used to demonstrate a lack of cross-contamination on neighboring microelectrodes in the array.

Laminar Soot Processes (Lsp) Experiment: Findings From Ground-Based Measurements

NASA Technical Reports Server (NTRS)

Kim, C. H.; El-Leathy, A. M.; Faeth, G. M.; Xu, F.

2003-01-01

Processes of soot formation and oxidation must be understood in order to achieve reliable computational combustion calculations for nonpremixed (diffusion) flames involving hydrocarbon fuels. Motivated by this observation, the present investigation extended earlier work on soot formation and oxidation in laminar jet ethylene/air and methane/oxygen premixed and acetylene-nitrogen/air diffusion flames at atmospheric pressure in this laboratory, emphasizing soot surface growth and early soot surface oxidation in laminar diffusion flames fueled with a variety of hydrocarbons at pressures in the range 0.1 - 1.0 atm.

On the role of resonantly stabilized radicals in polycyclic aromatic hydrocarbon (PAH) formation: pyrene and fluoranthene formation from benzyl-indenyl addition.

PubMed

Sinha, Sourab; Rahman, Ramees K; Raj, Abhijeet

2017-07-26

Resonantly stabilized radicals, such as propargyl, cyclopentadienyl, benzyl, and indenyl, play a vital role in the formation and growth of polycyclic aromatic hydrocarbons (PAHs) that are soot precursors in engines and flames. Pyrene is considered to be an important PAH, as it is thought to nucleate soot particles, but its formation pathways are not well known. This paper presents a reaction mechanism for the formation of four-ring aromatics, pyrene and fluoranthene, through the combination of benzyl and indenyl radicals. The intermediate species and transition structures involved in the elementary reactions of the mechanism were studied using density functional theory, and the reaction kinetics were evaluated using transition state theory. The barrierless addition of benzyl and indenyl to form the adduct, 1-benzyl-1H-indene, was found to be exothermic with a reaction energy of 204.2 kJ mol -1 . The decomposition of this adduct through H-abstraction and H 2 -loss was studied to determine the possible products. The rate-of-production analysis was conducted to determine the most favourable reactions for pyrene and fluoranthene formation. The premixed laminar flames of toluene, ethylbenzene, and benzene were simulated using a well-validated hydrocarbon fuel mechanism with detailed PAH chemistry after adding the proposed reactions to it. The computed and experimentally observed species profiles were compared to determine the effect of the new reactions for pyrene and fluoranthene formation on their concentration profiles. The role of benzyl and indenyl combination in PAH formation and growth is highlighted.

Petroleum geology of the Cusiana Field, Llanos Basin Foothills, Colombia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cazier, E.C.; Hayward, A.B.; Espinosa, G.

1995-10-01

Cusiana field is located in the Llanos Foothills, 150 mi (240km) northeast of Bogota, Colombia. Light oil, gas, and condensate in Cusiana occur at drilling depths that average 15,000 ft (4575 m) in an asymmetric, hanging-wall anticlinal trap 15 mi (25 km) long and 3-4 mi (5-6 km) across, formed during the Miocene-Holocene deformation of the Eastern Cordillera. Top and lateral seals are provided by marine mudstones of the Oligocene Carbonera Group, and support a hydrocarbon column of over 1500 ft (460 m). Biomarker data from the hydrocarbons indicate a marine mudstone source interpreted to be the Turonian-Coniacian Gacheta Formation.more » Over 50% of the reserves occur in upper Eocene Mirador Formation sandstones, which were deposited predominantly in estuarine environments. Additional, deeper reservoirs include estuarine sandstones of the Paleocene Barco Formation and the shallow-marine Santonian-Campanian Upper Guadalupe Sandstone. Porosity in Cusiana is relatively low. Good permeability is retained, however, because the reservoirs are pure quartz-cemented quartzarenites that lack permeability-reducing authigenic clays and carbonate cements. Core and well test analyses indicate matrix permeability, not fracture permeability, provides the high deliverability of Cusiana wells. Cusiana hydrocarbon phases exist in a near-miscible, critical-point state. Reservoir simulation indicates very high liquid hydrocarbon recoveries should be possible from all reservoirs by using the reinjection of produced gas to maintain reservoir pressure and to vaporize residual liquids. The field contains up to 1.5 MSTB of hydrocarbon liquid reserves and 3.4 Tcf of gas.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchsbaum, L.

Phoenix Coal currently operates 3 surface coal mines in Western Kentucky and have recently obtained the permits to construct their first underground mine. The expansion of the Phoenix Coal company since its formation in July 2004 is described. 4 photos.

Basic Considerations in the Combustion of Hydrocarbon Fuels with Air

NASA Technical Reports Server (NTRS)

Barnett, Henry C; Hibbard, Robert R

1957-01-01

Basic combustion research is collected, collated, and interpreted as it applies to flight propulsion. The following fundamental processes are treated in separate chapters: atomization and evaporation of liquid fuels, flow and mixing processes in combustion chambers, ignition and flammability of hydrocarbon fuels, laminar flame propagation, turbulent flames, flame stabilization, diffusion flames, oscillations in combustors, and smoke and coke formation in the combustion of hydrocarbon-air mixtures. Theoretical background, basic experimental data, and practical significance to flight propulsion are presented.

Biological enhancement of hydrocarbon extraction

DOEpatents

Brigmon, Robin L [North Augusta, SC; Berry, Christopher J [Aiken, SC

2009-01-06

A method of microbial enhanced oil recovery for recovering oil from an oil-bearing rock formation is provided. The methodology uses a consortium of bacteria including a mixture of surfactant producing bacteria and non-surfactant enzyme producing bacteria which may release hydrocarbons from bitumen containing sands. The described bioprocess can work with existing petroleum recovery protocols. The consortium microorganisms are also useful for treatment of above oil sands, ground waste tailings, subsurface oil recovery, and similar materials to enhance remediation and/or recovery of additional hydrocarbons from the materials.

Role of water in hydrocarbon generation from Type-I kerogen in Mahogany oil shale of the Green River Formation

USGS Publications Warehouse

Lewan, M.D.; Roy, S.

2011-01-01

Hydrous and anhydrous closed-system pyrolysis experiments were conducted on a sample of Mahogany oil shale (Eocene Green River Formation) containing Type-I kerogen to determine whether the role of water had the same effect on petroleum generation as reported for Type-II kerogen in the Woodford Shale. The experiments were conducted at 330 and 350??C for 72h to determine the effects of water during kerogen decomposition to polar-rich bitumen and subsequent bitumen decomposition to hydrocarbon-rich oil. The results showed that the role of water was more significant in bitumen decomposition to oil at 350??C than in kerogen decomposition to bitumen at 330??C. At 350??C, the hydrous experiment generated 29% more total hydrocarbon product and 33% more C15+ hydrocarbons than the anhydrous experiment. This is attributed to water dissolved in the bitumen serving as a source of hydrogen to enhance thermal cracking and facilitate the expulsion of immiscible oil. In the absence of water, cross linking is enhanced in the confines of the rock, resulting in formation of pyrobitumen and molecular hydrogen. These differences are also reflected in the color and texture of the recovered rock. Despite confining liquid-water pressure being 7-9 times greater in the hydrous experiments than the confining vapor pressure in the anhydrous experiments, recovered rock from the former had a lighter color and expansion fractures parallel to the bedding fabric of the rock. The absence of these open tensile fractures in the recovered rock from the anhydrous experiments indicates that water promotes net-volume increase reactions like thermal cracking over net-volume decrease reactions like cross linking, which results in pyrobitumen. The results indicate the role of water in hydrocarbon and petroleum formation from Type-I kerogen is significant, as reported for Type-II kerogen. ?? 2010.

Organic geochemistry of core samples from an ultradeep hot well (300°C, 7 km)

USGS Publications Warehouse

Price, Leigh C.

1982-01-01

Concepts prevelant among petroleum organic geochemists concerning the thermal fate of hydrocarbons, with subsequent graphite formation, and greenschist metamorphism, are in sharp contradiction to these data. Conventional concepts of the distribution of heavy hydrocarbons with increasing temperature and depth apparently require further review and revision.

Numerical Analysis of Extremely-rich CH4/O2/H2O Premixed Flames at High Pressure and High Temperature Considering Production of Higher Hydrocarbons

NASA Astrophysics Data System (ADS)

Kumagami, Manabu; Ogami, Yasuhiro; Tamaki, Yuichi; Kobayashi, Hideaki

Numerical analysis of CH4/O2/H2O laminar premixed flame under various conditions of pressure, equivalence ratio and steam concentration was performed using GRI-Mech 3.0 and the mechanism proposed by Davis and Law, which consists of C1 to C6 hydrocarbons in addition to GRI-Mech 3.0. The pressure dependence of laminar burning velocity and flame structure under fuel-rich conditions was focused on. Effects of the formation of higher hydrocarbons under fuel-rich conditions were also clarified using the mechanism proposed by Davis and Law. Results showed that for extremely fuel-rich conditions, laminar burning velocity increases as pressure increases for both mechanisms. The increase of laminar burning velocity is caused by the shift of the oxidation pathway of CH3 radical from the C2 Route to the C1 Route. The formation of C3-C6 hydrocarbons has only a small effect on laminar burning velocity. Under fuel-rich conditions, super-adiabatic flame temperature (SAFT) occurs and its pressure dependency was clarified.

40 CFR 146.6 - Area of review.

Code of Federal Regulations, 2014 CFR

2014-07-01

... lateral distance in which the pressures in the injection zone may cause the migration of the injection and... injection zone may cause the migration of the injection and/or formation fluid into an underground source of...

40 CFR 146.6 - Area of review.

Code of Federal Regulations, 2013 CFR

2013-07-01

... lateral distance in which the pressures in the injection zone may cause the migration of the injection and... injection zone may cause the migration of the injection and/or formation fluid into an underground source of...

40 CFR 146.6 - Area of review.

Code of Federal Regulations, 2011 CFR

2011-07-01

... lateral distance in which the pressures in the injection zone may cause the migration of the injection and... injection zone may cause the migration of the injection and/or formation fluid into an underground source of...

Noble gases identify the mechanisms of fugitive gas contamination in drinking-water wells overlying the Marcellus and Barnett Shales

PubMed Central

Darrah, Thomas H.; Vengosh, Avner; Jackson, Robert B.; Warner, Nathaniel R.; Poreda, Robert J.

2014-01-01

Horizontal drilling and hydraulic fracturing have enhanced energy production but raised concerns about drinking-water contamination and other environmental impacts. Identifying the sources and mechanisms of contamination can help improve the environmental and economic sustainability of shale-gas extraction. We analyzed 113 and 20 samples from drinking-water wells overlying the Marcellus and Barnett Shales, respectively, examining hydrocarbon abundance and isotopic compositions (e.g., C2H6/CH4, δ13C-CH4) and providing, to our knowledge, the first comprehensive analyses of noble gases and their isotopes (e.g., 4He, 20Ne, 36Ar) in groundwater near shale-gas wells. We addressed two questions. (i) Are elevated levels of hydrocarbon gases in drinking-water aquifers near gas wells natural or anthropogenic? (ii) If fugitive gas contamination exists, what mechanisms cause it? Against a backdrop of naturally occurring salt- and gas-rich groundwater, we identified eight discrete clusters of fugitive gas contamination, seven in Pennsylvania and one in Texas that showed increased contamination through time. Where fugitive gas contamination occurred, the relative proportions of thermogenic hydrocarbon gas (e.g., CH4, 4He) were significantly higher (P < 0.01) and the proportions of atmospheric gases (air-saturated water; e.g., N2, 36Ar) were significantly lower (P < 0.01) relative to background groundwater. Noble gas isotope and hydrocarbon data link four contamination clusters to gas leakage from intermediate-depth strata through failures of annulus cement, three to target production gases that seem to implicate faulty production casings, and one to an underground gas well failure. Noble gas data appear to rule out gas contamination by upward migration from depth through overlying geological strata triggered by horizontal drilling or hydraulic fracturing. PMID:25225410

Noble gases identify the mechanisms of fugitive gas contamination in drinking-water wells overlying the Marcellus and Barnett Shales.

PubMed

Darrah, Thomas H; Vengosh, Avner; Jackson, Robert B; Warner, Nathaniel R; Poreda, Robert J

2014-09-30

Horizontal drilling and hydraulic fracturing have enhanced energy production but raised concerns about drinking-water contamination and other environmental impacts. Identifying the sources and mechanisms of contamination can help improve the environmental and economic sustainability of shale-gas extraction. We analyzed 113 and 20 samples from drinking-water wells overlying the Marcellus and Barnett Shales, respectively, examining hydrocarbon abundance and isotopic compositions (e.g., C2H6/CH4, δ(13)C-CH4) and providing, to our knowledge, the first comprehensive analyses of noble gases and their isotopes (e.g., (4)He, (20)Ne, (36)Ar) in groundwater near shale-gas wells. We addressed two questions. (i) Are elevated levels of hydrocarbon gases in drinking-water aquifers near gas wells natural or anthropogenic? (ii) If fugitive gas contamination exists, what mechanisms cause it? Against a backdrop of naturally occurring salt- and gas-rich groundwater, we identified eight discrete clusters of fugitive gas contamination, seven in Pennsylvania and one in Texas that showed increased contamination through time. Where fugitive gas contamination occurred, the relative proportions of thermogenic hydrocarbon gas (e.g., CH4, (4)He) were significantly higher (P < 0.01) and the proportions of atmospheric gases (air-saturated water; e.g., N2, (36)Ar) were significantly lower (P < 0.01) relative to background groundwater. Noble gas isotope and hydrocarbon data link four contamination clusters to gas leakage from intermediate-depth strata through failures of annulus cement, three to target production gases that seem to implicate faulty production casings, and one to an underground gas well failure. Noble gas data appear to rule out gas contamination by upward migration from depth through overlying geological strata triggered by horizontal drilling or hydraulic fracturing.

Oxidation and formation of deposit precursors in hydrocarbon fuels

NASA Technical Reports Server (NTRS)

Mayo, F. R.; Lan, B.; Cotts, D. B.; Buttrill, S. E., Jr.; St.john, G. A.

1983-01-01

The oxidation of two jet turbine fuels and some pure hydrocarbons was studied at 130 C with and without the presence of small amounts of N-methyl pyrrole (NMP) or indene. Tendency to form solid-deposit precursors was studied by measuring soluble gum formation as well as dimer and trimer formation using field ionization mass spectrometry. Pure n-dodecane oxidized fastest and gave the smallest amount of procursors. An unstable fuel oil oxidized much slower but formed large amounts of precursors. Stable Jet A fuel oxidized slowest and gave little precursors. Indene either retarded or accelerated the oxidation of n-dodecane, depending on its concentration, but always caused more gum formation. The NMP greatly retarded n-dodecane oxidation but accelerated Jet A oxidation and greatly increased the latter's gum formation. In general, the additive reacted faster and formed most of the gum. Results are interpreted in terms of classical cooxidation theory. The effect of oxygen pressure on gum formation is also reported.

Catagenesis of organic matter of oil source rocks in Upper Paleozoic coal formation of the Bohai Gulf basin (eastern China)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, R.X.; Li, Y.Z.; Gao, Y.W.

2007-05-15

The Bohai Gulf basin is the largest petroliferous basin in China. Its Carboniferous-Permian deposits are thick (on the average, ca. 600 m) and occur as deeply as 5000 m. Coal and carbonaceous shale of the Carboniferous Taiyuan Formation formed in inshore plain swamps. Their main hydrocarbon-generating macerals are fluorescent vitrinite, exinite, alginite, etc. Coal and carbonaceous shale of the Permian Shanxi Formation were deposited in delta-alluvial plain. Their main hydrocarbon-generating macerals are vitrinite, exinite, etc. The carbonaceous rocks of these formations are characterized by a high thermal maturity, with the vitrinite reflectance R{sub 0} > 2.0%. The Bohai Gulf basinmore » has been poorly explored so far, but it is highly promising for natural gas.« less

Noble gas partitioning behavior in the Sleipner Vest hydrocarbon field

NASA Astrophysics Data System (ADS)

Barry, P. H.; Lawson, M.; Warr, O.; Mabry, J.; Byrne, D. J.; Meurer, W. P.; Ballentine, C. J.

2015-12-01

Noble gases are chemically inert and variably soluble in crustal fluids. They are primarily introduced into hydrocarbon reservoirs through exchange with formation waters, and can be used to assess migration pathways, mechanisms and reservoir storage. Of particular interest is the role groundwater plays in hydrocarbon transport, which is reflected in hydrocarbon-water volume ratios. We present compositional, stable isotope and noble gas isotope and abundance data from the Sleipner Vest field, in the Norwegian North Sea. Sleipner gases are generated from primary cracking of kerogen and the thermal cracking of oil, sourced from type II marine source, with relatively homogeneous maturities and a range in vitrinite reflectance (1.2-1.7%). Gases are hosted in the lower shoreface sandstones of the Jurassic Hugin formation, which is sealed by the Jurassic Upper Draupne and Heather formations. Gases are composed of N2 (0.6-0.9%), CO2 (5.4-15.3%) and hydrocarbons (69-80%). Helium isotopes (3He/4He) are radiogenic and range from 0.065 to 0.116 RA, showing a small mantle contribution, consistent with Ne isotopes (20Ne/22Ne from 9.70-9.91; 21Ne/22Ne from 0.0290-0.0344) and Ar isotopes (40Ar/36Ar from 315-489). 20Ne/36Ar, 84Kr/36Ar and 132Xe/36Ar values are systematically higher relative to air saturated water ratios. These data are discussed within the framework of several conceptual models: i) Total gas-stripping model, which defines the minimum volume of water to have interacted with the hydrocarbon phase; ii) Equilibrium model, assuming simple equilibration between groundwater and hydrocarbon phase at reservoir P,T and salinity; and iii) Open and closed system gas-stripping models. Using Ne-Ar, we estimate gas-water ratios for the Sleipner system of 0.02-0.09, which compare with geologic gas-water estimates of ~0.24, and suggest more groundwater interaction than a static system estimate. Kr and Xe show evidence for an additional source or process involving oil or sediments.

Hydrocarbon source-rock evaluation - Solor Church Formation (middle Proterozoic, Keweenawan Supergroup), southeastern Minnesota

USGS Publications Warehouse

Hatch, J.R.; Morey, G.B.

1984-01-01

In the type section (Lonsdale 65-1 core, Rice County, Minnesota) the Solor Church Formation (Middle Proterozoic, Keweenawan Supergroup) consists primarily of reddish-brown mudstone and siltstone and pale reddish-brown sandstone. The sandstone and siltstone are texturally and mineralogically immature. Hydrocarbon source-rock evaluation of bluish-gray, greenish-gray and medium-dark-gray to grayish-black beds, which primarily occur in the lower 104 m (340 ft) of this core, shows: (1) the rocks have low organic carbon contents (<0.5 percent for 22 of 25 samples); (2) the organic matter is thermally very mature (Tmax = 494°C, sample 19) and is probably near the transition between the wet gas phase of catagenesis and metagenesis (dry gas zone); and (3) the rocks have minimal potential for producing additional hydrocarbons (genetic potential <0.30 mgHC/gm rock). Although no direct evidence exists from which to determine maximum depths of burial, the observed thermal maturity of the organic matter requires significantly greater depths of burial and(or) higher geothermal gradients. It is likely, at least on the St. Croix horst, that thermal alteration of the organic matter in the Solor Church took place relatively early, and that any hydrocarbons generated during this early thermal alteration were probably lost prior to deposition of the overlying Fond du Lac Formation (Middle Proterozoic, Keweenawan Supergroup).

Hydrocarbon source rock evaluation: Solor Church Formation. (Middle Proterozoic, Keweenawan Supergroup) southeastern Minnesota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatch, J.R.; Morey, G.B.

In the type section (Lonsdale 65-1 core, Rice County, Minnesota) the Solar Church Formation (Middle Proterozoic, Keweenawan Supergroup) consists primarily of reddish-brown mudstone and siltstone and pale reddish-brown sandstone. The sandstone and siltstone are texturally and mineralogically immature. Hydrocarbon source-rock evaluation of bluish-gray, greenish-gray and medium-dark-gray to grayish-black beds, which primarily occur in the lower 104 m (340 ft) of this core, shows: (1) the rocks have low organic carbon contents (<0.5% for 22 of 25 samples); (2) the organic matter is thermally very mature (T/sub max/ = 494/sup 0/C, sample 19) and is probably near the transition between themore » wet gas phase of catagenesis and metagenesis (dry gas zone); and (3) the rocks have minimal potential for producing additional hydrocarbons (genetic potential <0.30 mgHC/gm rock). Although no direct evidence exists from which to determine maximum depths of burial, the observed thermal maturity of the organic matter requires significantly greater depths of burial and(or) higher geothermal gradients. It is likely, at least on the St. Croix horst, that thermal alteration of the organic matter in the Solor Church took place relatively early, and that any hydrocarbons generated during this early thermal alteration were probably lost prior to deposition of the overlying Fond du Lac Formation (Middle Proterozoic, Keweenawan Supergroup). 5 figs., 2 tabs.« less

Precursor soot synthesis of fullerenes and nanotubes without formation of carbonaceous soot

DOEpatents

Reilly, Peter T. A.

2007-03-20

The present invention is a method for the synthesis of fullerenes and/or nanotubes from precursor soot without the formation of carbonaceous soot. The method comprises the pyrolysis of a hydrocarbon fuel source by heating the fuel source at a sufficient temperature to transform the fuel source to a condensed hydrocarbon. The condensed hydrocarbon is a reaction medium comprising precursor soot wherein hydrogen exchange occurs within the reaction medium to form reactive radicals which cause continuous rearrangement of the carbon skeletal structure of the condensed hydrocarbon. Then, inducing dehydrogenation of the precursor soot to form fullerenes and/or nanotubes free from the formation of carbonaceous soot by continued heating at the sufficient temperature and by regulating the carbon to hydrogen ratio within the reaction medium. The dehydrogenation process produces hydrogen gas as a by-product. The method of the present invention in another embodiment is also a continuous synthesis process having a continuous supply of the fuel source. The method of the present invention can also be a continuous cyclic synthesis process wherein the reaction medium is fed back into the system as a fuel source after extraction of the fullerenes and/or nanotube products. The method of the present invention is also a method for producing precursor soot in bulk quantity, then forming fullerenes and/or nanotubes from the precursor bulk.

Autothermal reforming of aliphatic and aromatic hydrocarbon liquids

NASA Technical Reports Server (NTRS)

Flytzani-Stephanopoulos, M.; Voecks, G. E.

1983-01-01

Results are presented from a study of the autothermal reforming of paraffins and aromatics over nickel catalysts. The trials were performed to examine the carbon products that appear when steam is passed over hydrocarbon liquids to form H2-rich gases, i.e., the autothermal process (ATR). Attention was given to n-hexane, n-tetradecane, benzene, and benzene solutions of naphthalene with reactant preheat to 1000-1150 F. The carbon-formation limit was sought as a function of the steam-to-carbon and oxygen to carbon molar ratios at constant pressure and the preheat temperatures. The catalyst bed was examined after each trial to identify the locations and types of carbon formed using SEM, thermal gravimetric analysis, and X ray diffraction techniques. The hydrocarbon fuels each had a separate temperature and reaction profile, as well as carbon formation characteristics. No carbon formation was observed in the upper layer of the reactor bed, while both gas phase and surface-grown deposits were present in the lower part. The results are concluded of use in the study of No. 2 fuel oil for ATR feedstock.

Livermore study says oil leaks not severe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patrick, L.

The Petroleum Marketers Association of America (PMAA), which is working to reform the federal Leaking Underground Storage Tank program, got some strong ammunition last month. A study that the Lawrence Livermore National Laboratory performed for the California State Water Resources Control Board has found that the environmental threat of leaks is not as severe as formerly thought. The study said: such leaks rarely jeopardize drinking water; fuel hydrocarbons have limited impacts on health, the environment, and groundwater; and cleanups often are done contrary to the knowledge and experience gained from prior remediations. As a result of the study, Gov. Petemore » Wilson ordered California cleanups halted at sites more than 250 feet from drinking water supplies.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dagle, Robert A.; Lizarazo Adarme, Jair A.; Lebarbier, Vanessa MC

A composite Pd/ZnO/Al2O3-HZSM-5 (Si/Al=40) catalytic system was evaluated for the synthesis of gasoline-range hydrocarbons directly from synthesis gas. Bifunctional catalyst comprising PdZn metal and acid sites present the required catalytically active sites necessary for the methanol synthesis, methanol dehydration, and methanol-to-gasoline reactions. This system provides a unique catalytic pathway for the production of liquid hydrocarbons directly from syngas. However, selectivity control is difficult and poses many challenges. The composite catalytic system was evaluated under various process conditions. Investigated were the effects of temperature (310-375oC), pressure (300-1000 psig), time-on-stream (50 hrs), and gas-hour space velocity (740-2970 hr-1), using a H2/CO molarmore » syngas ratio of 2.0. By operating at the lower end of the temperature range investigated, liquid hydrocarbon formation was favored, as was decreased amounts of undesirable light hydrocarbons. However, lower operating temperatures also facilitated undesirable CO2 formation via the water-gas shift reaction. Higher operating pressures slightly favored liquid synthesis. Operating at relatively low pressures (e.g. 300 psig) was made possible, whereas for methanol synthesis alone higher pressure are usually required to achieve similar conversion levels (e.g. 1000 psig). Thermodynamic constraints on methanol synthesis are eased by pushing the equilibrium through hydrocarbon formation. Catalytic performance was also evaluated by altering Pd and Zn composition of the Pd/ZnO/Al2O3 catalyst. Of the catalysts and conditions tested, selectivity toward liquid hydrocarbon was highest when using a 5% Pd metal loading and Pd/Zn molar ratio of 0.25 and mixed with HZMS-5, operating at 310oC and 300 psig, CO conversion was 43 % and selectivity (carbon weight basis) to hydrocarbons was 49 wt. %. Of the hydrocarbon fraction, 44wt. % was in the C5-C12 liquid product range and consisted primarily of aromatic polymethylbenzenes. However, as syngas conversion increases with increasing temperature, selectivity to liquid product diminished. This is attributed, in large part, to increased saturation of the olefinic intermediates over PdZn metal sites. Under all the conditions and catalysts evaluated in this study, generating liquid product in high yield was challenging (<10 wt. % C5+ yield).« less

The Diesel Exhaust in Miners Study: I. Overview of the Exposure Assessment Process

PubMed Central

Stewart, Patricia A.; Coble, Joseph B.; Vermeulen, Roel; Schleiff, Patricia; Blair, Aaron; Lubin, Jay; Attfield, Michael; Silverman, Debra T.

2010-01-01

This report provides an overview of the exposure assessment process for an epidemiologic study that investigated mortality, with a special focus on lung cancer, associated with diesel exhaust (DE) exposure among miners. Details of several components are provided in four other reports. A major challenge for this study was the development of quantitative estimates of historical exposures to DE. There is no single standard method for assessing the totality of DE, so respirable elemental carbon (REC), a component of DE, was selected as the primary surrogate in this study. Air monitoring surveys at seven of the eight study mining facilities were conducted between 1998 and 2001 and provided reference personal REC exposure levels and measurements for other agents and DE components in the mining environment. (The eighth facility had closed permanently prior to the surveys.) Exposure estimates were developed for mining facility/department/job/year combinations. A hierarchical grouping strategy was developed for assigning exposure levels to underground jobs [based on job titles, on the amount of time spent in various areas of the underground mine, and on similar carbon monoxide (CO, another DE component) concentrations] and to surface jobs (based on the use of, or proximity to, diesel-powered equipment). Time trends in air concentrations for underground jobs were estimated from mining facility-specific prediction models using diesel equipment horsepower, total air flow rates exhausted from the underground mines, and, because there were no historical REC measurements, historical measurements of CO. Exposures to potentially confounding agents, i.e. respirable dust, silica, radon, asbestos, and non-diesel sources of polycyclic aromatic hydrocarbons, also were assessed. Accuracy and reliability of the estimated REC exposures levels were evaluated by comparison with several smaller datasets and by development of alternative time trend models. During 1998–2001, the average measured REC exposure level by facility ranged from 40 to 384 μg m−3 for the underground workers and from 2 to 6 μg m−3 for the surface workers. For one prevalent underground job, ‘miner operator’, the maximum annual REC exposure estimate by facility ranged up to 685% greater than the corresponding 1998–2001 value. A comparison of the historical CO estimates from the time trend models with 1976–1977 CO measurements not used in the modeling found an overall median relative difference of 29%. Other comparisons showed similar levels of agreement. The assessment process indicated large differences in REC exposure levels over time and across the underground operations. Method evaluations indicated that the final estimates were consistent with those from alternative time trend models and demonstrated moderate to high agreement with external data. PMID:20876233

The diesel exhaust in miners study: I. Overview of the exposure assessment process.

PubMed

Stewart, Patricia A; Coble, Joseph B; Vermeulen, Roel; Schleiff, Patricia; Blair, Aaron; Lubin, Jay; Attfield, Michael; Silverman, Debra T

2010-10-01

This report provides an overview of the exposure assessment process for an epidemiologic study that investigated mortality, with a special focus on lung cancer, associated with diesel exhaust (DE) exposure among miners. Details of several components are provided in four other reports. A major challenge for this study was the development of quantitative estimates of historical exposures to DE. There is no single standard method for assessing the totality of DE, so respirable elemental carbon (REC), a component of DE, was selected as the primary surrogate in this study. Air monitoring surveys at seven of the eight study mining facilities were conducted between 1998 and 2001 and provided reference personal REC exposure levels and measurements for other agents and DE components in the mining environment. (The eighth facility had closed permanently prior to the surveys.) Exposure estimates were developed for mining facility/department/job/year combinations. A hierarchical grouping strategy was developed for assigning exposure levels to underground jobs [based on job titles, on the amount of time spent in various areas of the underground mine, and on similar carbon monoxide (CO, another DE component) concentrations] and to surface jobs (based on the use of, or proximity to, diesel-powered equipment). Time trends in air concentrations for underground jobs were estimated from mining facility-specific prediction models using diesel equipment horsepower, total air flow rates exhausted from the underground mines, and, because there were no historical REC measurements, historical measurements of CO. Exposures to potentially confounding agents, i.e. respirable dust, silica, radon, asbestos, and non-diesel sources of polycyclic aromatic hydrocarbons, also were assessed. Accuracy and reliability of the estimated REC exposures levels were evaluated by comparison with several smaller datasets and by development of alternative time trend models. During 1998-2001, the average measured REC exposure level by facility ranged from 40 to 384 μg m⁻³ for the underground workers and from 2 to 6 μg m⁻³ for the surface workers. For one prevalent underground job, 'miner operator', the maximum annual REC exposure estimate by facility ranged up to 685% greater than the corresponding 1998-2001 value. A comparison of the historical CO estimates from the time trend models with 1976-1977 CO measurements not used in the modeling found an overall median relative difference of 29%. Other comparisons showed similar levels of agreement. The assessment process indicated large differences in REC exposure levels over time and across the underground operations. Method evaluations indicated that the final estimates were consistent with those from alternative time trend models and demonstrated moderate to high agreement with external data.

Catalytic autothermal reforming increases fuel cell flexibility

NASA Technical Reports Server (NTRS)

Flytzani-Stephanopoulos, M.; Voecks, G. E.

1981-01-01

Experimental results are presented for the autothermal reforming (ATR) of n-hexane, n-tetradecane, benzene and benzene solutions of naphthalene. The tests were run at atmospheric pressure and at moderately high reactant preheat temperatures in the 800-900 K range. Carbon formation lines were determined for paraffinic and aromatic liquids. Profiles were determined for axial bed temperature and composition. Space velocity efforts were assessed, and the locations and types of carbon were recorded. Significant reactive differences between hydrocarbons were identified. Carbon formation characteristics were hydrocarbon specific. The differing behavior of paraffinic and aromatic fuels with respect to their carbon formation may be important in explaining the narrow range of carbon-free operating conditions found in the ATR of number two fuel oil.

Geological problems in radioactive waste isolation - A world wide review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witherspoon, P.A.

1991-06-01

The problem of isolating radioactive wastes from the biosphere presents specialists in the earth sciences with some of the most complicated problems they have ever encountered. This is especially true for high-level waste (HLW), which must be isolated in the underground and away from the biosphere for thousands of years. The most widely accepted method of doing this is to seal the radioactive materials in metal canisters that are enclosed by a protective sheath and placed underground in a repository that has been carefully constructed in an appropriate rock formation. Much new technology is being developed to solve the problemsmore » that have been raised, and there is a continuing need to publish the results of new developments for the benefit of all concerned. Table 1 presents a summary of the various formations under investigation according to the reports submitted for this world wide review. It can be seen that in those countries that are searching for repository sites, granitic and metamorphic rocks are the prevalent rock type under investigation. Six countries have developed underground research facilities that are currently in use. All of these investigations are in saturated systems below the water table, except the United States project, which is in the unsaturated zone of a fractured tuff.« less

Time-Dependent Damage Investigation of Rock Mass in an In Situ Experimental Tunnel

PubMed Central

Jiang, Quan; Cui, Jie; Chen, Jing

2012-01-01

In underground tunnels or caverns, time-dependent deformation or failure of rock mass, such as extending cracks, gradual rock falls, etc., are a costly irritant and a major safety concern if the time-dependent damage of surrounding rock is serious. To understand the damage evolution of rock mass in underground engineering, an in situ experimental testing was carried out in a large belowground tunnel with a scale of 28.5 m in width, 21 m in height and 352 m in length. The time-dependent damage of rock mass was detected in succession by an ultrasonic wave test after excavation. The testing results showed that the time-dependent damage of rock mass could last a long time, i.e., nearly 30 days. Regression analysis of damage factors defined by wave velocity, resulted in the time-dependent evolutional damage equation of rock mass, which corresponded with logarithmic format. A damage viscoelastic-plastic model was developed to describe the exposed time-dependent deterioration of rock mass by field test, such as convergence of time-dependent damage, deterioration of elastic modules and logarithmic format of damage factor. Furthermore, the remedial measures for damaged surrounding rock were discussed based on the measured results and the conception of damage compensation, which provides new clues for underground engineering design.

Muon tomography in the Mont Terri underground rock laboratory

NASA Astrophysics Data System (ADS)

Lesparre, N.; Gibert, D.; Marteau, J.; Carlus, B.; Nussbaum, C.

2012-04-01

The Mont Terri underground rock laboratory (Switzerland) was excavated in a Mesozoic shale formation constituted by Opalinus clay. This impermeable formation presents suitable properties for hosting repository sites of radioactive waste. A muon telescope has been placed in this laboratory in October 2009 to establish the feasibility of the muon tomography and to test the sensor performance in a calm environment, where we are protected from atmospheric noisy particles. However, the presence of radon in the gallery as well as charged particles issued from the decay of gamma rays may create a background noise. This noise shift and smooths the signal inducing an under estimation of the rock density. The uncorrelated background has been measured by placing the planes of detection in anti-coincidence. This estimation is preponderant and has to be combined to the theoretical feasibility evaluation to determine the best experimental set-up to observe muon flux fluctuations due to density variations. The muon densitometry experience is here exposed with the estimation of its feasibility. The data acquired from different locations inside the underground laboratory are presented. They are compared to two models representing the layer above the laboratory corresponding to a minimum and a maximum muon flux expectation depending on the values of the rock density.

76 FR 80937 - Notice of Final 2010 Effluent Guidelines Program Plan; Re-Opening Public Comment Period

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... develop standards for wastewater discharges produced by natural gas extraction from underground coalbed and shale formations as well as mercury discharges from dental offices. EPA is also accepting...

The performance of ammonium exchanged zeolite for the biodegradation of petroleum hydrocarbons migrating in soil water.

PubMed

Freidman, Benjamin L; Gras, Sally L; Snape, Ian; Stevens, Geoff W; Mumford, Kathryn A

2016-08-05

Nitrogen deficiency has been identified as the main inhibiting factor for biodegradation of petroleum hydrocarbons in low nutrient environments. This study examines the performance of ammonium exchanged zeolite to enhance biodegradation of petroleum hydrocarbons migrating in soil water within laboratory scale flow cells. Biofilm formation and biodegradation were accelerated by the exchange of cations in soil water with ammonium in the pores of the exchanged zeolite when compared with natural zeolite flow cells. These results have implications for sequenced permeable reactive barrier design and the longevity of media performance within such barriers at petroleum hydrocarbon contaminated sites deficient in essential soil nutrients. Copyright © 2016 Elsevier B.V. All rights reserved.

How fast do hydrocarbons condense in Titan's atmosphere? Insights from the laboratory

NASA Astrophysics Data System (ADS)

Biennier, L.; Bourgalais, J.; Capron, M.; Roussel, V.; Le Picard, S. D.

2014-04-01

Titan's dense atmosphere shows a complex photochemistry initiated by the dissociation of its two most abundant components, nitrogen N2 and methane CH4. This cold chemistry generates a plethora of hydrocarbons and nitriles and takes part in the production of a thick haze. According to a recent scenario constructed from Cassini-Huygens measurements, the chemical reactions and physical processes occurring at high altitudes near 1000 km could be the haze source [1]. This haze material could act as a nucleus for the condensation of organic vapors in Titan's stratosphere and troposphere. However, the pathways leading to the formation and growth of haze aerosols remain far to be well understood. Hydrocarbons, which are formed in Titan's cold atmosphere, starting with ethane C2H6, ethylene C2H4, acetylene C2H2, propane C3H8… up to benzene C6H6, play also some active role in aerosol production, cloud processes, rain generation and Titan's lakes formation. Our goal is to study in the laboratory the kinetics of the first steps of condensation of these hydrocarbon molecules. Several studies have investigated the phase of e.g. ethane and propane and their spectral signatures. At the exception of our recent studies on the dimerization of pyrene C16H10 [2] and anthracene C14H10 [3] performed over the 50-300 K temperature range, there is however no other work on the first elementary steps of the kinetics of nucleation for hydrocarbons. Here we present the first experimental kinetics study of the dimerization of a small hydrocarbon: propane C3H8. We have performed experiments to identify the temperature range over which small propane clusters form in saturated uniform supersonic flows. Using our unique reactor based on a Laval nozzle [4], the kinetics of the formation has also been investigated over the 15-300 K temperature range. The chemical species present in the reactor are probed by a time of flight mass spectrometer equipped with an electron gun for soft ionization of the neutral reagents and products. The experimental data is combined with state-of-the-art theoretical calculations that employ careful consideration of the intermolecular interaction energies and intermolecular dynamics to estimate the binding energy, equilibrium constant, and rate coefficients. This work aims at putting some constraints on the role of small hydrocarbon condensation in the formation of haze particles in the dense atmosphere of Titan.

Flooded Underground Coal Mines: A Significant Source of Inexpensive Geothermal Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watzlaf, G.R.; Ackman, T.E.

2007-04-01

Many mining regions in the United States contain extensive areas of flooded underground mines. The water within these mines represents a significant and widespread opportunity for extracting low-grade, geothermal energy. Based on current energy prices, geothermal heat pump systems using mine water could reduce the annual costs for heating to over 70 percent compared to conventional heating methods (natural gas or heating oil). These same systems could reduce annual cooling costs by up to 50 percent over standard air conditioning in many areas of the country. (Formatted full-text version is released by permission of publisher)

Petroleum Systems and Assessment of Undiscovered Oil and Gas in the Raton Basin - Sierra Grande Uplift Province, Colorado and New Mexico - USGS Province 41

USGS Publications Warehouse

Higley, Debra K.

2007-01-01

Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas resources of the Raton Basin-Sierra Grande Uplift Province of southeastern Colorado and northeastern New Mexico (USGS Province 41). The Cretaceous Vermejo Formation and Cretaceous-Tertiary Raton Formation have production and undiscovered resources of coalbed methane. Other formations in the province exhibit potential for gas resources and limited production. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and five assessment units. All five assessment units were quantitatively assessed for undiscovered gas resources. Oil resources were not assessed because of the limited potential due to levels of thermal maturity of petroleum source rocks.

Formation of charged nanoparticles in hydrocarbon flames: principal mechanisms

NASA Astrophysics Data System (ADS)

Starik, A. M.; Savel'ev, A. M.; Titova, N. S.

2008-11-01

The processes of charged gaseous and particulate species formation in sooting hydrocarbon/air flame are studied. The original kinetic model, comprising the chemistry of neutral and charged gaseous species, generation of primary clusters, which then undergo charging due to attachment of ions and electrons to clusters and via thermoemission, and coagulation of charged-charged, charged-neutral and neutral-neutral particles, is reported. The analysis shows that the principal mechanisms of charged particle origin in hydrocarbon flames are associated with the attachment of ions and electrons produced in the course of chemoionization reactions to primary small clusters and particles and coagulation via charged-charged and charged-neutral particle interaction. Thermal ionization of particles does not play a significant role in the particle charging. This paper was presented at the Third International Symposium on Nonequilibrium Process, combustion, and Atmospheric Phenomena (Dagomys, Sochi, Russia, 25-29 June 2007).

A metal-free electrocatalyst for carbon dioxide reduction to multi-carbon hydrocarbons and oxygenates

NASA Astrophysics Data System (ADS)

Wu, Jingjie; Ma, Sichao; Sun, Jing; Gold, Jake I.; Tiwary, Chandrasekhar; Kim, Byoungsu; Zhu, Lingyang; Chopra, Nitin; Odeh, Ihab N.; Vajtai, Robert; Yu, Aaron Z.; Luo, Raymond; Lou, Jun; Ding, Guqiao; Kenis, Paul J. A.; Ajayan, Pulickel M.

2016-12-01

Electroreduction of carbon dioxide into higher-energy liquid fuels and chemicals is a promising but challenging renewable energy conversion technology. Among the electrocatalysts screened so far for carbon dioxide reduction, which includes metals, alloys, organometallics, layered materials and carbon nanostructures, only copper exhibits selectivity towards formation of hydrocarbons and multi-carbon oxygenates at fairly high efficiencies, whereas most others favour production of carbon monoxide or formate. Here we report that nanometre-size N-doped graphene quantum dots (NGQDs) catalyse the electrochemical reduction of carbon dioxide into multi-carbon hydrocarbons and oxygenates at high Faradaic efficiencies, high current densities and low overpotentials. The NGQDs show a high total Faradaic efficiency of carbon dioxide reduction of up to 90%, with selectivity for ethylene and ethanol conversions reaching 45%. The C2 and C3 product distribution and production rate for NGQD-catalysed carbon dioxide reduction is comparable to those obtained with copper nanoparticle-based electrocatalysts.

In situ chemical stimulation of diatomite formations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.W.

1989-05-09

A method is described of recovering hydrocarbon from a subsurface diatomite formation comprising the steps of: a. introducing an aqueous surface solution into the diatomite formation, the aqueous surface active solution comprising (i) a diatomite/oil/ water wettability improving agent, and (ii) an oil/water interfacial tension lowering agent; and b. producing oil from the diatomite formation.

Method of pressurizing and stabilizing rock by periodic and repeated injections of a settable fluid of finite gel strength

DOEpatents

Colgate, Stirling A.

1983-01-01

A finite region of overpressure can be created in solid underground formations by the periodic injection of a fluid that has finite gel strength that subsequently, after each injection, partially sets--i.e., equivalently becomes a very much stronger gel. A region of overpressure is a region in which the static, locked in pressure is larger than what was there before. A region of overpressure can be used to prevent a roof of a tunnel from caving by adding compressive stresses in the roof. A sequence of regions of overpressure can be used to lift an arch or dome underground, squeeze off water or gas flows, stabilize dams, foundations, large underground rooms, etc. In general, the stress or pressure distribution in rock can be altered and engineered in a fashion that is more advantageous than what would have been the case without overstressing.

Method of pressurizing and stabilizing rock by periodic and repeated injections of a settable fluid of finite gel strength

DOEpatents

Colgate, S.A.

1983-01-25

A finite region of overpressure can be created in solid underground formations by the periodic injection of a fluid that has finite gel strength that subsequently, after each injection, partially sets--i.e., equivalently becomes a very much stronger gel. A region of overpressure is a region in which the static, locked in pressure is larger than what was there before. A region of overpressure can be used to prevent a roof of a tunnel from caving by adding compressive stresses in the roof. A sequence of regions of overpressure can be used to lift an arch or dome underground, squeeze off water or gas flows, stabilize dams, foundations, large underground rooms, etc. In general, the stress or pressure distribution in rock can be altered and engineered in a fashion that is more advantageous than what would have been the case without overstressing. 3 figs.

Influence of Aerosol Acidity on the Formation of Secondary Organic Aerosol from Biogenic Precursor Hydrocarbons

EPA Science Inventory

Secondary organic aerosol (SOA) formation and dynamics may be important factors for the role of aerosols in adverse health effects, visibility and climate change. Formation of SOA occurs when a parent volatile organic compound is oxidized to create products that form in a conden...

Determining the Area of Review for Industrial Waste Disposal Wells.

DTIC Science & Technology

1981-12-01

pressure increases sufficiently to force formation fluids and/or injected wastes up abandoned well bores to contaminate underground sources of drinking...Drilling Mud Circulating System . . 72 9. Increase in Gel Strength of Various Mud Types With Time . . . . . . . . . . . . . . . . . . 96 10. Gel... increased fluid pressure in a disposal zone which results from a waste injection operation may force injected and/or formation fluid to migrate up an

Varying heating in dawsonite zones in hydrocarbon containing formations

DOEpatents

Vinegar, Harold J [Bellaire, TX; Xie, Xueying [Houston, TX; Miller, David Scott [Katy, TX

2009-07-07

A method for treating an oil shale formation comprising dawsonite includes assessing a dawsonite composition of one or more zones in the formation. Heat from one or more heaters is provided to the formation such that different amounts of heat are provided to zones with different dawsonite compositions. The provided heat is allowed to transfer from the heaters to the formation. Fluids are produced from the formation.

Experimental and analytical study of nitric oxide formation during combustion of propane in a jet-stirred combustor

NASA Technical Reports Server (NTRS)

Wakelyn, N. T.; Jachimowski, C. J.; Wilson, C. H.

1978-01-01

A jet-stirred combustor, constructed of castable zirconia and with an Inconel injector, was used to study nitric oxide formation in propane-air combustion with residence times in the range from 3.2 to 3.3 msec and equivalence ratios varying from 0.7 to 1.4. Measurements were made of combustor operating temperature and of nitric oxide concentration. Maximum nitric oxide concentrations of the order of 55 ppm were found in the range of equivalence ratio from 1.0 to 1.1. A finite-rate chemical kinetic mechanism for propane combustion and nitric oxide formation was assembled by coupling an existing propane oxidation mechanism with the Zeldovich reactions and reactions of molecular nitrogen with hydrocarbon fragments. Analytical studies using this mechanism in a computer simulation of the experimental conditions revealed that the hydrocarbon-fragment-nitrogen reactions play a significant role in nitric oxide formation during fuel-rich combustion.

In situ measurements of the photochemical formation rates and optical properties of organic aerosols in CH4/CO2 mixtures.

NASA Astrophysics Data System (ADS)

Adamkovics, M.; Boering, K. A.

2003-12-01

The presence of photochemically-generated hazes has a significant impact on radiative transfer in planetary atmospheres. While the rates of particle formation have been inferred from photochemical or microphysical models constrained to match observations, these rates have not been determined experimentally. Thus, the fundamental kinetics of particle formation are not known and remain highly parameterized in planetary atmospheric models. We have developed instrumentation for measuring the formation rates and optical properties of organic aerosols produced by irradiating mixtures of precursor gases via in situ optical (633nm) scattering and online quadrupole mass spectrometry (1-200 amu). Results for the generation of particulate hydrocarbons from the irradiation of pure, gas-phase CH4 as well as CH4/CO2 mixtures with vacuum ultraviolet (120-160nm) light, along with simultaneous measurements of the evolution of higher gas-phase hydrocarbons will be presented.

Formation of H{sub 2} from internally heated polycyclic aromatic hydrocarbons: Excitation energy dependence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, T., E-mail: tao.chen@fysik.su.se, E-mail: henning@fysik.su.se; Gatchell, M.; Stockett, M. H.

2015-04-14

We have investigated the effectiveness of molecular hydrogen (H{sub 2}) formation from Polycyclic Aromatic Hydrocarbons (PAHs) which are internally heated by collisions with keV ions. The present and earlier experimental results are analyzed in view of molecular structure calculations and a simple collision model. We estimate that H{sub 2} formation becomes important for internal PAH temperatures exceeding about 2200 K, regardless of the PAH size and the excitation agent. This suggests that keV ions may effectively induce such reactions, while they are unlikely due to, e.g., absorption of single photons with energies below the Lyman limit. The present analysis alsomore » suggests that H{sub 2} emission is correlated with multi-fragmentation processes, which means that the [PAH-2H]{sup +} peak intensities in the mass spectra may not be used for estimating H{sub 2}-formation rates.« less

Discrete fracture modeling of multiphase flow and hydrocarbon production in fractured shale or low permeability reservoirs

NASA Astrophysics Data System (ADS)

Hao, Y.; Settgast, R. R.; Fu, P.; Tompson, A. F. B.; Morris, J.; Ryerson, F. J.

2016-12-01

It has long been recognized that multiphase flow and transport in fractured porous media is very important for various subsurface applications. Hydrocarbon fluid flow and production from hydraulically fractured shale reservoirs is an important and complicated example of multiphase flow in fractured formations. The combination of horizontal drilling and hydraulic fracturing is able to create extensive fracture networks in low permeability shale rocks, leading to increased formation permeability and enhanced hydrocarbon production. However, unconventional wells experience a much faster production decline than conventional hydrocarbon recovery. Maintaining sustainable and economically viable shale gas/oil production requires additional wells and re-fracturing. Excessive fracturing fluid loss during hydraulic fracturing operations may also drive up operation costs and raise potential environmental concerns. Understanding and modeling processes that contribute to decreasing productivity and fracturing fluid loss represent a critical component for unconventional hydrocarbon recovery analysis. Towards this effort we develop a discrete fracture model (DFM) in GEOS (LLNL multi-physics computational code) to simulate multiphase flow and transfer in hydraulically fractured reservoirs. The DFM model is able to explicitly account for both individual fractures and their surrounding rocks, therefore allowing for an accurate prediction of impacts of fracture-matrix interactions on hydrocarbon production. We apply the DFM model to simulate three-phase (water, oil, and gas) flow behaviors in fractured shale rocks as a result of different hydraulic stimulation scenarios. Numerical results show that multiphase flow behaviors at the fracture-matrix interface play a major role in controlling both hydrocarbon production and fracturing fluid recovery rates. The DFM model developed in this study will be coupled with the existing hydro-fracture model to provide a fully integrated geomechanical and reservoir simulation capability for an accurate prediction and assessment of hydrocarbon production and hydraulic fracturing performance. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

1-D/3-D geologic model of the Western Canada Sedimentary Basin

USGS Publications Warehouse

Higley, D.K.; Henry, M.; Roberts, L.N.R.; Steinshouer, D.W.

2005-01-01

The 3-D geologic model of the Western Canada Sedimentary Basin comprises 18 stacked intervals from the base of the Devonian Woodbend Group and age equivalent formations to ground surface; it includes an estimated thickness of eroded sediments based on 1-D burial history reconstructions for 33 wells across the study area. Each interval for the construction of the 3-D model was chosen on the basis of whether it is primarily composed of petroleum system elements of reservoir, hydrocarbon source, seal, overburden, or underburden strata, as well as the quality and areal distribution of well and other data. Preliminary results of the modeling support the following interpretations. Long-distance migration of hydrocarbons east of the Rocky Mountains is indicated by oil and gas accumulations in areas within which source rocks are thermally immature for oil and (or) gas. Petroleum systems in the basin are segmented by the northeast-trending Sweetgrass Arch; hydrocarbons west of the arch were from source rocks lying near or beneath the Rocky Mountains, whereas oil and gas east of the arch were sourced from the Williston Basin. Hydrocarbon generation and migration are primarily due to increased burial associated with the Laramide Orogeny. Hydrocarbon sources and migration were also influenced by the Lower Cretaceous sub-Mannville unconformity. In the Peace River Arch area of northern Alberta, Jurassic and older formations exhibit high-angle truncations against the unconformity. Potential Paleozoic though Mesozoic hydrocarbon source rocks are in contact with overlying Mannville Group reservoir facies. In contrast, in Saskatchewan and southern Alberta the contacts are parallel to sub-parallel, with the result that hydrocarbon source rocks are separated from the Mannville Group by seal-forming strata within the Jurassic. Vertical and lateral movement of hydrocarbons along the faults in the Rocky Mountains deformed belt probably also resulted in mixing of oil and gas from numerous source rocks in Alberta.

Flow of Gas and Water in Hydraulically Fractured Shale Gas Reservoirs, March 28-29, 2011

EPA Pesticide Factsheets

Underground fluid flow is primarily controlled by two physical factors: hydraulic conduits and pressure gradients. Both are required, or fluids will not move. In their natural state, shale formations are very impermeable.

A Field Study of NMR Logging to Quantify Petroleum Contamination in Subsurface Sediments

NASA Astrophysics Data System (ADS)

Fay, E. L.; Knight, R. J.; Grunewald, E. D.

2016-12-01

Nuclear magnetic resonance (NMR) measurements are directly sensitive to hydrogen-bearing fluids including water and petroleum products. NMR logging tools can be used to detect and quantify petroleum hydrocarbon contamination in the sediments surrounding a well or borehole. An advantage of the NMR method is that data can be collected in both cased and uncased holes. In order to estimate the volume of in-situ hydrocarbon, there must be sufficient contrast between either the relaxation times (T2) or the diffusion coefficients (D) of water and the contaminant. In a field study conducted in Pine Ridge, South Dakota, NMR logging measurements were used to investigate an area of hydrocarbon contamination from leaking underground storage tanks. A contaminant sample recovered from a monitoring well at the site was found to be consistent with a mixture of gasoline and diesel fuel. NMR measurements were collected in two PVC-cased monitoring wells; D and T2 measurements were used together to detect and quantify contaminant in the sediments above and below the water table at both of the wells. While the contrast in D between the fluids was found to be inadequate for fluid typing, the T2 contrast between the contaminant and water in silt enabled the estimation of the water and contaminant volumes. This study shows that NMR logging can be used to detect and quantify in-situ contamination, but also highlights the importance of sediment and contaminant properties that lead to a sufficiently large contrast in T2 or D.

A detailed kinetic modeling study of aromatics formation in laminar premixed acetylene and ethylene flames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, H.; Frenklach, M.

1997-07-01

A computational study was performed for the formation and growth of polycyclic aromatic hydrocarbons (PAHs) in laminar premixed acetylene and ethylene flames. A new detailed reaction mechanism describing fuel pyrolysis and oxidation, benzene formation, and PAH mass growth and oxidation is presented and critically tested. It is shown that the reaction model predicts reasonably well the concentration profiles of major and intermediate species and aromatic molecules in a number of acetylene and ethylene flames reported in the literature. It is demonstrated that reactions of n-C{sub 4}H{sub x} + C{sub 2}H{sub 2} leading to the formation of one-ring aromatics are asmore » important as the propargyl recombination, and hence must be included in kinetic modeling of PAH formation in hydrocarbon flames. It is further demonstrated that the mass growth of PAHs can be accounted for by the previously proposed H-abstraction-C{sub 2}H{sub 2}-addiction mechanism.« less

Effect of beer marinades on formation of polycyclic aromatic hydrocarbons in charcoal-grilled pork.

PubMed

Viegas, Olga; Yebra-Pimentel, Iria; Martínez-Carballo, Elena; Simal-Gandara, Jesus; Ferreira, Isabel M P L V O

2014-03-26

The effect of marinating meat with Pilsner beer, nonalcoholic Pilsner beer, and Black beer (coded respectively PB, P0B, and BB) on the formation of polycyclic aromatic hydrocarbons (PAHs) in charcoal-grilled pork was evaluated and compared with the formation of these compounds in unmarinated meat. Antiradical activity of marinades (DPPH assay) was assayed. BB exhibited the strongest scavenging activity (68.0%), followed by P0B (36.5%) and PB (29.5%). Control and marinated meat samples contained the eight PAHs named PAH8 by the EFSA and classified as suitable indicators for carcinogenic potency of PAHs in food. BB showed the highest inhibitory effect in the formation of PAH8 (53%), followed by P0B (25%) and PB (13%). The inhibitory effect of beer marinades on PAH8 increased with the increase of their radical-scavenging activity. BB marinade was the most efficient on reduction of PAH formation, providing a proper mitigation strategy.

Coke formation in a zeolite crystal during the methanol-to-hydrocarbons reaction as studied with atom probe tomography

DOE PAGES

Schmidt, Joel E.; Poplawsky, Jonathan D.; Mazumder, Baishakhi; ...

2016-08-03

Understanding the formation of carbon deposits in zeolites is vital to developing new, superior materials for various applications, including oil and gas conversion processes. Herein, atom probe tomography (APT) has been used to spatially resolve the 3D compositional changes at the sub-nm length scale in a single zeolite ZSM-5 crystal, which has been partially deactivated by the methanol-to-hydrocarbons reaction using 13C-labeled methanol. The results reveal the formation of coke in agglomerates that span length scales from tens of nanometers to atomic clusters with a median size of 30–60 13C atoms. These clusters correlate with local increases in Brønsted acid sitemore » density, demonstrating that the formation of the first deactivating coke precursor molecules occurs in nanoscopic regions enriched in aluminum. Here, this nanoscale correlation underscores the importance of carefully engineering materials to suppress detrimental coke formation.« less

Pre-drilling prediction techniques on the high-temperature high-pressure hydrocarbon reservoirs offshore Hainan Island, China

NASA Astrophysics Data System (ADS)

Zhang, Hanyu; Liu, Huaishan; Wu, Shiguo; Sun, Jin; Yang, Chaoqun; Xie, Yangbing; Chen, Chuanxu; Gao, Jinwei; Wang, Jiliang

2018-02-01

Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure (HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques (PPTs). To improve the accuracy of geopressure prediction in HTHP hydrocarbon reservoirs offshore Hainan Island, we made a comprehensive summary of current PPTs to identify existing problems and challenges by analyzing the global distribution of HTHP hydrocarbon reservoirs, the research status of PPTs, and the geologic setting and its HTHP formation mechanism. Our research results indicate that the HTHP formation mechanism in the study area is caused by multiple factors, including rapid loading, diapir intrusions, hydrocarbon generation, and the thermal expansion of pore fluids. Due to this multi-factor interaction, a cloud of HTHP hydrocarbon reservoirs has developed in the Ying-Qiong Basin, but only traditional PPTs have been implemented, based on the assumption of conditions that do not conform to the actual geologic environment, e.g., Bellotti's law and Eaton's law. In this paper, we focus on these issues, identify some challenges and solutions, and call for further PPT research to address the drawbacks of previous works and meet the challenges associated with the deepwater technology gap. In this way, we hope to contribute to the improved accuracy of geopressure prediction prior to drilling and provide support for future HTHP drilling offshore Hainan Island.

Heterobimetallic Zeolite, InV-ZSM-5, Enables Efficient Conversion of Biomass Derived Ethanol to Renewable Hydrocarbons

NASA Astrophysics Data System (ADS)

Narula, Chaitanya K.; Li, Zhenglong; Casbeer, Erik M.; Geiger, Robert A.; Moses-Debusk, Melanie; Keller, Martin; Buchanan, Michelle V.; Davison, Brian H.

2015-11-01

Direct catalytic conversion of ethanol to hydrocarbon blend-stock can increase biofuels use in current vehicles beyond the ethanol blend-wall of 10-15%. Literature reports describe quantitative conversion of ethanol over zeolite catalysts but high C2 hydrocarbon formation renders this approach unsuitable for commercialization. Furthermore, the prior mechanistic studies suggested that ethanol conversion involves endothermic dehydration step. Here, we report the complete conversion of ethanol to hydrocarbons over InV-ZSM-5 without added hydrogen and which produces lower C2 (<13%) as compared to that over H-ZSM-5. Experiments with C2H5OD and in situ DRIFT suggest that most of the products come from the hydrocarbon pool type mechanism and dehydration step is not necessary. Thus, our method of direct conversion of ethanol offers a pathway to produce suitable hydrocarbon blend-stock that may be blended at a refinery to produce fuels such as gasoline, diesel, JP-8, and jet fuel, or produce commodity chemicals such as BTX.

Heterobimetallic Zeolite, InV-ZSM-5, Enables Efficient Conversion of Biomass Derived Ethanol to Renewable Hydrocarbons.

PubMed

Narula, Chaitanya K; Li, Zhenglong; Casbeer, Erik M; Geiger, Robert A; Moses-Debusk, Melanie; Keller, Martin; Buchanan, Michelle V; Davison, Brian H

2015-11-03

Direct catalytic conversion of ethanol to hydrocarbon blend-stock can increase biofuels use in current vehicles beyond the ethanol blend-wall of 10-15%. Literature reports describe quantitative conversion of ethanol over zeolite catalysts but high C2 hydrocarbon formation renders this approach unsuitable for commercialization. Furthermore, the prior mechanistic studies suggested that ethanol conversion involves endothermic dehydration step. Here, we report the complete conversion of ethanol to hydrocarbons over InV-ZSM-5 without added hydrogen and which produces lower C2 (<13%) as compared to that over H-ZSM-5. Experiments with C2H5OD and in situ DRIFT suggest that most of the products come from the hydrocarbon pool type mechanism and dehydration step is not necessary. Thus, our method of direct conversion of ethanol offers a pathway to produce suitable hydrocarbon blend-stock that may be blended at a refinery to produce fuels such as gasoline, diesel, JP-8, and jet fuel, or produce commodity chemicals such as BTX.

Analysis of hydrocarbons generated in coalbeds

NASA Astrophysics Data System (ADS)

Butala, Steven John M.

This dissertation describes kinetic calculations using literature data to predict formation rates and product yields of oil and gas at typical low-temperature conditions in coalbeds. These data indicate that gas formation rates from hydrocarbon thermolysis are too low to have generated commercial quantities of natural gas, assuming bulk first-order kinetics. Acid-mineral-catalyzed cracking, transition-metal-catalyzed hydrogenolysis of liquid hydrocarbons, and catalyzed CO2 hydrogenation form gas at high rates. The gaseous product compositions for these reactions are nearly the same as those for typical natural coalbed gases, while those from thermal and catalytic cracking are more representative of atypical coalbed gases. Three Argonne Premium Coals (Upper-Freeport, Pittsburgh #8 and Lewiston-Stockton) were extracted with benzene in both Soxhlet and elevated pressure extraction (EPE) systems. The extracts were compared on the basis of dry mass yield and hydrocarbon profiles obtained by gas chromatography/mass spectrometry. The dry mass yields for the Upper-Freeport coal gave consistent results by both methods, while the yields from the Pittsburgh #8 and Lewiston-Stockton coals were greater by the EPE method. EPE required ˜90 vol. % less solvent compared to Soxhlet extraction. Single-ion-chromatograms of the Soxhlet extracts all exhibited bimodal distributions, while those of the EPE extracts did not. Hydrocarbons analyzed from Greater Green River Basin samples indicate that the natural oils in the basin originated from the coal seams. Analysis of artificially produced oil indicates that hydrous pyrolysis mimics generation of C15+ n-alkanes, but significant variations were found in the branched alkane, low-molecular-weight n-alkanes, and high-molecular-weight aromatic hydrocarbon distributions.

Geologic assessment of undiscovered oil and gas resources in Aptian carbonates, onshore northern Gulf of Mexico Basin, United States

USGS Publications Warehouse

Hackley, Paul C.; Karlsen, Alexander W.

2014-01-01

Carbonate lithofacies of the Lower Cretaceous Sligo Formation and James Limestone were regionally evaluated using established U.S. Geological Survey (USGS) assessment methodology for undiscovered conventional hydrocarbon resources. The assessed area is within the Upper Jurassic–Cretaceous–Tertiary Composite total petroleum system, which was defined for the assessment. Hydrocarbons reservoired in carbonate platform Sligo-James oil and gas accumulations are interpreted to originate primarily from the Jurassic Smackover Formation. Emplacement of hydrocarbons occurred via vertical migration along fault systems; long-range lateral migration also may have occurred in some locations. Primary reservoir facies include porous patch reefs developed over paleostructural salt highs, carbonate shoals, and stacked linear reefs at the carbonate shelf margin. Hydrocarbon traps dominantly are combination structural-stratigraphic. Sealing lithologies include micrite, calcareous shale, and argillaceous lime mudstone. A geologic model, supported by discovery history analysis of petroleum geology data, was used to define a single regional assessment unit (AU) for conventional reservoirs in carbonate facies of the Sligo Formation and James Limestone. The AU is formally entitled Sligo-James Carbonate Platform Oil and Gas (50490121). A fully risked mean undiscovered technically recoverable resource in the AU of 50 million barrels of oil (MMBO), 791 billion cubic feet of natural gas (BCFG), and 26 million barrels of natural gas liquids was estimated. Substantial new development through horizontal drilling has occurred since the time of this assessment (2010), resulting in cumulative production of >200 BCFG and >1 MMBO.

"Super-Reducing" Photocatalysis: Consecutive Energy and Electron Transfers with Polycyclic Aromatic Hydrocarbons.

PubMed

Brasholz, Malte

2017-08-21

Donation welcome: Recent developments in visible-light photocatalysis allow the utilization of increasingly negative reduction potentials. Successive energy and electron transfer with polycyclic aromatic hydrocarbons enables the catalytic formation of strongly reducing arene radical anions, classical stoichiometric reagents for one-electron reduction in organic synthesis. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

FORMATION OF POLYKETONES IN IRRADIATED TOLUENE/PROPYLENE/NOX/AIR MIXTURES

EPA Science Inventory

A laboratory study was carried out to investigate the formation of polyketones in secondary organic aerosol from photooxidation of the aromatic hydrocarbon toluene, a major constituent of automobile exhaust. The laboratory experiments consisted of irradiating toluene/propylene...

Protection of groundwater from oil pollution in the vicinity of airports

DOE Office of Scientific and Technical Information (OSTI.GOV)

Svoma, J.; Houzim, V.

1984-01-01

The potential danger to the quality of groundwater close to airports is due to a combination of several ecologically unfavorable factors. Airports are usually situated in the proximity of a groundwater divide, or in wide valleys. Causes of pollution include the sheer volume of fluid being handled constantly, the physicochemical properties of hydrocarbons, and technical errors in the transport and storage of fuels. Oil hydrocarbons in concentrations of tenths to units of milligrams per liter have been found in snow in the vicinity of runways. Carcinogenic benzopyrenes are accumulated in soil. Oil hydrocarbons spread in rock formations as a separatemore » layer was well as in solution. In porous permeable formations, pollution by a free product affects areas on the order of tens of meters, while hydrocarbons in solution penetrate to distances of hundreds of meters or even kilometers. Fissured rocks are cause for even more complex conditions for the spreading of oil based substances. Preventive protection of groundwater and mineral waters using monitoring devices is being carried out at some major airports. Observation wells situated in the tectonic zone can also be used for reparative pumping. 12 references, 7 figures, 3 tables.« less

Solar Spectrum Photocatalytic Conversion of CO2 and Water Vapor Into Hydrocarbons Using TiO2 Nanoparticle Membranes

NASA Astrophysics Data System (ADS)

Rani, Sanju; Bao, Ningzhong; Roy, Somnath C.

2014-01-01

A viable option for recycling carbon dioxide is through the sunlight-powered photocatalytic conversion of CO2 and water vapor into hydrocarbon fuels over highly active nanocatalysts. With photocatalytic CO2 reduction sunlight, a renewable energy source as durable as the sun, is used to drive the catalytic reaction with the resultant fuel products compatible with the current hydrocarbon-based energy infrastructure. The use of co-catalyst (Cu, Pt)-sensitized TiO2 nanoparticle wafers in the photocatalytic conversion of CO2 and water vapor to hydrocarbon fuels, with optimal humidity levels and exposure times established. We also attempted to increase product formation by sputtering both co-catalysts on the nanoparticle wafer's surface, with the resulting product rates significantly higher than that of either the Cu or Pt coated samples. When the TiO2 nanoparticle wafers are used in a flow-through membrane implementation we find a significant increase in product rates of formation, including methane, hydrogen, and carbon monoxide. We believe that nanocatalyst-based flow-through membranes are a viable route for achieving large-scale and low cost photocatalytic solar fuel production.

Growth Kinetics and Mechanics of Hydrate Films by Interfacial Rheology.

PubMed

Leopércio, Bruna C; de Souza Mendes, Paulo R; Fuller, Gerald G

2016-05-03

A new approach to study and understand the kinetics and mechanical properties of hydrates by interfacial rheology is presented. This is made possible using a "double wall ring" interfacial rheology cell that has been designed to provide the necessary temperature control. Cyclopentane and water are used to form hydrates, and this model system forms these structures at ambient pressures. Different temperature and water/hydrocarbon contact protocols are explored. Of particular interest is the importance of first contacting the hydrocarbon against ice crystals in order to initiate hydrate formation. Indeed, this is found to be the case, even though the hydrates may be created at temperatures above the melting point of ice. Once hydrates completely populate the hydrocarbon/water interface, strain sweeps of the interfacial elastic and viscous moduli are conducted to interrogate the mechanical response and fragility of the hydrate films. The dependence on temperature, Tf, by the kinetics of formation and the mechanical properties is reported, and the cyclopentane hydrate dissociation temperature was found to be between 6 and 7 °C. The formation time (measured from the moment when cyclopentane first contacts ice crystals) as well as the elastic modulus and the yield strain increase as Tf increases.

Natural fracking and the genesis of five-element veins

NASA Astrophysics Data System (ADS)

Markl, Gregor; Burisch, Mathias; Neumann, Udo

2016-08-01

Hydrothermal Ag-Co-Ni-Bi-As (five-element vein type) ore deposits show very conspicuous textures of the native elements silver, bismuth, and arsenic indicating formation from a rapid, far-from-equilibrium process. Such textures include up to dm-large tree- and wire-like aggregates overgrown by Co-Ni-Fe arsenides and mostly carbonates. Despite the historical and contemporary importance of five-element vein type deposits as sources of silver, bismuth, and cobalt, and despite of spectacular museum specimens, their process of formation is not yet understood and has been a matter of debate since centuries. We propose, based on observations from a number of classical European five-element vein deposits and carbon isotope analyses, that "natural fracking," i.e., liberation of hydrocarbons or hydrocarbon-bearing fluids during break up of rocks in the vicinity of an active hydrothermal system and mixing between these hydrocarbons (e.g., methane and/or methane-bearing fluids) and a metal-rich hydrothermal fluid is responsible for ore precipitation and the formation of the unusual ore textures and assemblages. Thermodynamic and isotope mixing calculations show that the textural, chemical, and isotopic features of the investigated deposits can entirely be explained by this mechanism.

Reactivation of a Propped Hydraulic Fracture

NASA Astrophysics Data System (ADS)

Sarvaramini, E.; Garagash, D.

2014-12-01

The problem of massive fluid injection into a pre-existing fracture has many applications in petroleum industry including underground liquid waste disposal and waterflooding to increase recovery from a hydrocarbon reservoir. Understanding the conditions leading to the re-activation of pre-existing fractures and ensuing propagation is critical for a successful injection project design, and it may also help to mitigate potential environmental hazards, such as contamination of underground aquifers and induced seismicity. The problem of injection of a low viscosity fluid into a permeable formation can be distinguished from conventional hydraulic fracture by the mechanism of fluid leak-off. In conventional fracturing, high viscosity and cake building properties of injected fluid limit leak-off to a 1-D boundary layer incasing the crack. In the case of injection of low viscosity fluid into a fracture, leak-off and related pore fluid diffusion will take place over wider range of scales, from 1-D to 2 or 3-D. We consider a pre-existing stationary propped hydraulic fracture with constrained height into which a fluid is injected under constant flow rate. Although the net effective stress on the crack is initially compressive, the proppant keeps the crack open. It is worthwhile to note that during injection and related pressurization of a propped crack, the fracture breakdown is to be achieved prior to the fracture re-opening. Therefore, the effect of the change of the propped fracture storage on the pressurization dynamics can be neglected. The objective of this work is to study the transient pressurization and the onset of the propagation for a propped fracture. To the end, we formulate and solve a general problem of injection into a fracture accounting for viscous dissipation (i.e. non-uniform pressure distribution). We quantify how the fracture breakdown condition depends upon the rock and fluid properties, the in-situ stress and the fluid injection rate. We also establish a criterion when the assumption of negligible viscous dissipation is justified. The obtained solution is also transportable to the production well test analysis of a fractured well (Cinco et al., SPE 1978).

Impact craters - Are they useful?

NASA Astrophysics Data System (ADS)

Masaitis, V. L.

1992-03-01

Terrestrial impact craters are important geological and geomorphological objects that are significant not only for scientific research but for industrial and commercial purposes. The structures may contain commercial minerals produced directly by thermodynamic transformation of target rocks (including primary forming ores) controlled by some morphological, structural or lithological factors and exposed in the crater. Iron and uranium ores, nonferrous metals, diamonds, coals, oil shales, hydrocarbons, mineral waters and other raw materials occur in impact craters. Impact morphostructures may be used for underground storage of gases or liquid waste material. Surface craters may serve as reservoirs for hydropower. These ring structures may be of value to society in other ways. Scientific investigation of them is especially important in comparative planetology, terrestrial geology and in other divisions of the natural sciences.

Real Time Oil Reservoir Evaluation Using Nanotechnology

NASA Technical Reports Server (NTRS)

Li, Jing (Inventor); Meyyappan, Meyya (Inventor)

2011-01-01

A method and system for evaluating status and response of a mineral-producing field (e.g., oil and/or gas) by monitoring selected chemical and physical properties in or adjacent to a wellsite headspace. Nanotechnology sensors and other sensors are provided for one or more underground (fluid) mineral-producing wellsites to determine presence/absence of each of two or more target molecules in the fluid, relative humidity, temperature and/or fluid pressure adjacent to the wellsite and flow direction and flow velocity for the fluid. A nanosensor measures an electrical parameter value and estimates a corresponding environmental parameter value, such as water content or hydrocarbon content. The system is small enough to be located down-hole in each mineral-producing horizon for the wellsite.

Method for inhibiting gum formation in liquid hydrocarbon mediums

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reid, D.K.

1990-07-17

This patent describes a method of inhibiting the formation of gum and sediment in a liquid hydrocarbonaceous medium. It comprises: adding to the medium an inhibiting amount of an alkyl 1,2-dihydroquinoline or polymerized alkyl 1,2-dihydroquinoline.

Role of Pt during hydrodeoxygenation of biomass pyrolysis vapors over Pt/HBEA

DOE PAGES

Yung, Matthew M.; Foo, Guo Shiou; Sievers, Carsten

2017-03-27

1.3 wt% Pt/HBEA and HBEA were studied as catalysts for the hydrodeoxygenation of pine pyrolysis vapors at 500 °C. Both catalysts showed high initial conversion of oxygenated pyrolysis products into aromatic hydrocarbons, while Pt/HBEA showed higher stability in terms of hydrocarbon productivity and deferred breakthrough of oxygenated compounds. Among 1-, 2- and 3-ring aromatic hydrocarbons, Pt/HBEA had a significantly higher selectivity than HBEA towards unalkylated aromatics (e.g., benzene) as compared to the corresponding alkylated aromatics (e.g., toluene and xylene). Additionally, Pt addition to HBEA decreased coke deposition and improved resistance to pore and acid site blockage as determined by TPO,more » N 2 physisorption, and NH 3 TPD. The ability of Pt to promote cleavage and hydrogenation of methoxy and methyl groups was observed by increased methane production over Pt/HBEA relative to HBEA. A progressive decrease in the methane production over Pt/HBEA correlated with deactivation in terms of reduced benzene formation, breakthrough of oxygenated products, and increased formation of polynuclear aromatics and their degree of substitution, which indicate coke formation. In conclusion, the increased methane yield and suppressed coke formation with the addition of Pt is attributed to hydrogen spillover, through which hydrogen activated on Pt can subsequently migrate to the HBEA support to reverse the coke-forming hydrogen abstraction reaction.« less

Role of Pt during hydrodeoxygenation of biomass pyrolysis vapors over Pt/HBEA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yung, Matthew M.; Foo, Guo Shiou; Sievers, Carsten

1.3 wt% Pt/HBEA and HBEA were studied as catalysts for the hydrodeoxygenation of pine pyrolysis vapors at 500 °C. Both catalysts showed high initial conversion of oxygenated pyrolysis products into aromatic hydrocarbons, while Pt/HBEA showed higher stability in terms of hydrocarbon productivity and deferred breakthrough of oxygenated compounds. Among 1-, 2- and 3-ring aromatic hydrocarbons, Pt/HBEA had a significantly higher selectivity than HBEA towards unalkylated aromatics (e.g., benzene) as compared to the corresponding alkylated aromatics (e.g., toluene and xylene). Additionally, Pt addition to HBEA decreased coke deposition and improved resistance to pore and acid site blockage as determined by TPO,more » N 2 physisorption, and NH 3 TPD. The ability of Pt to promote cleavage and hydrogenation of methoxy and methyl groups was observed by increased methane production over Pt/HBEA relative to HBEA. A progressive decrease in the methane production over Pt/HBEA correlated with deactivation in terms of reduced benzene formation, breakthrough of oxygenated products, and increased formation of polynuclear aromatics and their degree of substitution, which indicate coke formation. In conclusion, the increased methane yield and suppressed coke formation with the addition of Pt is attributed to hydrogen spillover, through which hydrogen activated on Pt can subsequently migrate to the HBEA support to reverse the coke-forming hydrogen abstraction reaction.« less

Comparison of transgressive and regressive clastic reservoirs, late Albian Viking Formation, Alberta basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reinson, G.E.

1996-06-01

Detailed stratigraphic analysis of hydrocarbon reservoirs from the Basal Colorado upwards through the Viking/Bow Island and Cardium formations indicates that the distributional trends, overall size and geometry, internal heterogeneity, and hydrocarbon productivity of the sand bodies are related directly to a transgressive-regressive (T-R) sequence stratigraphic model. The Viking Formation (equivalent to the Muddy Sandstone of Wyoming) contains examples of both transgressive and regressive reservoirs. Viking reservoirs can be divided into progradational shoreface bars associated with the regressive systems tract, and bar/sheet sands and estuary/channel deposits associated with the transgressive systems tract. Shoreface bars, usually consisting of fine- to medium-grained sandstones,more » are tens of kilometers long, kilometers in width, and in the order of five to ten meters thick. Transgressive bar and sheet sandstones range from coarse-grained to conglomeratic, and occur in deposits that are tens of kilometers long, several kilometers wide, and from less than one to four meters in thickness. Estuary and valley-fill reservoir sandstones vary from fine-grained to conglomeratic, occur as isolated bodies that have channel-like geometries, and are usually greater than 10 meters thick. From an exploration viewpoint the most prospective reservoir trends in the Viking Formation are those associated with transgressive systems tracts. In particular, bounding discontinuities between T-R systems tracts are the principal sites of the most productive hydrocarbon-bearing sandstones.« less

Centrifuge tests on simulation of the ''cookie cutter'' mechanism of chimney collapse into underground openings: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kutter, B.L.; Chang, Ging-Song

The underground testing of nuclear devices causes the formation of large underground cavities which eventually may be filled by rubble and soil falling from the roof of the cavity. The zone of collapsing soil progresses upward toward the ground surface to form a ''chimney.'' The mechanisms of chimney collapse are important to understand for two important reasons. (1) A devastating and sudden propagation of the collapse may result in the formation of a surface crater which may threaten personnel and equipment in the vicinity of the crater. (2) Different collapse patterns are known to occur in the field and somemore » of these collapse patterns are known to be associated with leakage of radioactive wastes to the ground surface. A number of centrifuge tests were conducted by Kutter et al. (1988), to study the collapse of cavities in uniform dry sands. In these materials, the chimney collapse patterns were found to involve continuous, smoothly varying shear strain patterns in the chimney. The pattern of collapse in one of the tests is shown in figure 1. Figure 1a shows the surface crater that formed on the ground surface due to the collapse of a 6 inch diameter cavity buried 18'' beneath the ground surface. This result was obtained by draining fluid out of a 6'' rubber bag while the centrifuge was spinning at 11 g.« less

Oxidative dehydrogenation of alkanes to unsaturated hydrocarbons

DOEpatents

Kung, H.H.; Chaar, M.A.

1988-10-11

Oxidative dehydrogenation of alkanes to unsaturated hydrocarbons is carried out over metal vanadate catalysts under oxidizing conditions. The vanadate catalysts are represented by the formulas M[sub 3](VO[sub 4])[sub 2] and MV[sub 2]O[sub 6], M representing Mg, Zn, Ca, Pb, or Cd. The reaction is carried out in the presence of oxygen, but the formation of oxygenate by-products is suppressed.

Oxidative dehydrogenation of alkanes to unsaturated hydrocarbons

DOEpatents

Kung, Harold H.; Chaar, Mohamed A.

1988-01-01

Oxidative dehydrogenation of alkanes to unsaturated hydrocarbons is carried out over metal vanadate catalysts under oxidizing conditions. The vanadate catalysts are represented by the formulas M.sub.3 (VO.sub.4).sub.2 and MV.sub.2 O.sub.6, M representing Mg, Zn, Ca, Pb, or Cd. The reaction is carried out in the presence of oxygen, but the formation of oxygenate by-products is suppressed.

Assessment of soil-gas contamination at building 310 underground storage tank area, Fort Gordon, Georgia, 2010-2011

USGS Publications Warehouse

Guimaraes, Wladmir B.; Falls, W. Fred; Caldwell, Andral W.; Ratliff, W. Hagan; Wellborn, John B.; Landmeyer, James E.

2012-01-01

Soil gas was assessed for contaminants in the building 310 underground storage tank area adjacent to the Dwight D. Eisenhower Army Medical Center at Ft. Gordon, Georgia, from October 2010 to September 2011. The assessment, which also included the detection of organic compounds in soil gas, provides environmental contamination data to Fort Gordon personnel pursuant to requirements of the Resource Conservation and Recovery Act Part B Hazardous Waste Permit process. The study was conducted by the U.S. Geological Survey, in cooperation with the U.S. Department of the Army Environmental and Natural Resources Management Office of the U.S. Army Signal Center and Fort Gordon. Soil-gas samplers were deployed below land surface at 37 locations in the building 310 underground storage tank area. Soil-gas samplers were deployed in a grid pattern near the storage tank area as well as downslope of the tank area in the direction of groundwater flow toward an unnamed tributary to Butler Creek. Total petroleum hydrocarbons were detected in 35 of the 37 soil-gas samplers at levels above the method detection level, and the combined mass of benzene, toluene, ethylbenzene, and total xylenes were detected above their detection levels in 8 of the 37 samplers. In addition, the combined masses of undecane, tridecane, and pentadecane were detected at or above their method detection levels in 9 of the 37 samplers. Other volatile organic compounds detected above their respective method detection levels were chloroform, 1,2,4-trimethylbenzene, and perchloroethylene. In addition, naphthalene, 2-methyl naphthalene, and 1,2,4-trimethylbenzene were detected below the method detection levels, but above the nondetection level.

Geochemical interpretation of distribution of aromatic hydrocarbons in components of geologic environment of Pechora, Barents and Kara seas.

NASA Astrophysics Data System (ADS)

Kursheva, Anna; Petrova, Vera; Litvinenko, Ivan; Morgunova, Inna

2017-04-01

Information about the hydrocarbons content (including aromatic ones) in components of geologic environment allows to define common factors in distribution and correlation both nature and technogenic component, and also to reveal the sources of contamination. At that, it should be noted, that hydrocarbons are widely spread in lithosphere and create steady geochemical background, variations are caused here by specifics of initial organic matter, conditions of its accumulation and transformation. The basis of the study are the samples of sea water and deep sea sediments (more than 600 stations), collected in western sector of Arctic region (Pechora, Barents and Kara seas) during the scientific-research expeditions of FSBI "VNIIOkeangeologia" for the period 2000-2010. Total content of aromatic hydrocarbons was defined by spectrofluorometric method using analyzer «FLUORAT-Panorama-02». Certification of data was performed on representative samples based on contents and molecule structure of polycyclic aromatic hydrocarbons using GC-MS (Agilent 5973/6850 GC-MS System). Results of spectrofluorometric analysis of lipid fraction of organic matter of bottom sediments allowed to define specific parameters, which characterize various lithofacies groups of sediments. Thus, sandy residues are characterized by low level of aromatic hydrocarbons (ca. 4.3 μg/g) with prevalence of bi- and tri-aromatic compounds (λmax 270-310 nm). This correlates with low sorption capacity of coarse-grained sediments and absence of organic-mineral component, containing the breakdown products of initial organic matter. Tetra- and penta- aromatic structures prevail in clay sediments (ca. 13.0 μg/g), which are typical components of lipid fraction of organic matter of post sedimentation and early diagenetic stages of transformation. At that, changes of spectral characteristic of sediments in stratigraphic sequence completely reflect processes of diagenetic transformation of organic matter, including aromatization and new formation of number of compounds, for example perylene (λmax 405,435 nm). The presence in sediments of highly transformed (post-diagenetic) organic material forms special (for naphthides) type of spectrum (λmax 370-380 nm), which interface is fundamentally different from recent marine sediments. Similar type of spectrum in combination with anomalously high content of aromatic hydrocarbons (ca. 349.1 μg/g) is typical, in particular, for shelf of Spitsbergen archipelago, whose erosion and redeposition of carboniferous rocks play important role in deposits formation. Similar content of aromatic hydrocarbons was noted in sediments of shelf of the Island Kolguev, where exogenous anomaly is caused mainly by anthropogenic factors. This assumption correlates with the results of aromatic hydrocarbons examination where pyrogenic components dominate. The influence of endogenous processes (seepage of hydrocarbons) also may lead to substantial deformation of background spectrum due to formation of intensive peak in short-wave region (λmax max 240-260 nm). Credibility of collected results is proven by significant correlation of quantitative estimation of aromatic hydrocarbons contents conducted using both dispersed organic matter extraction and fractionation and spectrofluorimetry methods. Results, received during GC-MS analysis also prove spectrofluorometric information.

Geologic assessment of undiscovered conventional oil and gas resources--Middle Eocene Claiborne Group, United States part of the Gulf of Mexico Basin

USGS Publications Warehouse

Hackley, Paul C.

2012-01-01

The Middle Eocene Claiborne Group was assessed using established U.S. Geological Survey (USGS) assessment methodology for undiscovered conventional hydrocarbon resources as part of the 2007 USGS assessment of Paleogene-Neogene strata of the United States part of the Gulf of Mexico Basin including onshore and State waters. The assessed area is within the Upper Jurassic-Cretaceous-Tertiary Composite total petroleum system, which was defined as part of the assessment. Source rocks for Claiborne oil accumulations are interpreted to be organic-rich downdip shaley facies of the Wilcox Group and the Sparta Sand of the Claiborne Group; gas accumulations may have originated from multiple sources including the Jurassic Smackover and Haynesville Formations and Bossier Shale, the Cretaceous Eagle Ford and Pearsall(?) Formations, and the Paleogene Wilcox Group and Sparta Sand. Hydrocarbon generation in the basin started prior to deposition of Claiborne sediments and is ongoing at present. Emplacement of hydrocarbons into Claiborne reservoirs has occurred primarily via vertical migration along fault systems; long-range lateral migration also may have occurred in some locations. Primary reservoir sands in the Claiborne Group include, from oldest to youngest, the Queen City Sand, Cook Mountain Formation, Sparta Sand, Yegua Formation, and the laterally equivalent Cockfield Formation. Hydrocarbon traps dominantly are rollover anticlines associated with growth faults; salt structures and stratigraphic traps also are important. Sealing lithologies probably are shaley facies within the Claiborne and in the overlying Jackson Group. A geologic model, supported by spatial analysis of petroleum geology data including discovered reservoir depths, thicknesses, temperatures, porosities, permeabilities, and pressures, was used to divide the Claiborne Group into seven assessment units (AU) with distinctive structural and depositional settings. The AUs include (1) Lower Claiborne Stable Shelf Gas and Oil (50470120), (2) Lower Claiborne Expanded Fault Zone Gas (50470121), (3) Lower Claiborne Slope and Basin Floor Gas (50470122), (4) Lower Claiborne Cane River (50470123), (5) Upper Claiborne Stable Shelf Gas and Oil (50470124), (6) Upper Claiborne Expanded Fault Zone Gas (50470125), and (7) Upper Claiborne Slope and Basin Floor Gas (50470126). Total estimated mean undiscovered conventional hydrocarbon resources in the seven assessment units combined are 52 million barrels of oil, 19.145 trillion cubic feet of natural gas, and 1.205 billion barrels of natural gas liquids. A recurring theme that emerged from the evaluation of the seven Claiborne AUs is that the great bulk of undiscovered hydrocarbon resources comprise non-associated gas and condensate contained in deep (mostly >12,000 feet), overpressured, structurally complex outer shelf or slope and basin floor reservoirs. The continuing development of these downdip objectives is expected to be the primary focus of exploration activity for the onshore Middle Eocene Gulf Coast in the coming decades.

SECONDARY ORGANIC AEROSOL FORMATION FROM THE IRRADIATION OF SIMULATED AUTOMOBILE EXHAUST

EPA Science Inventory

A laboratory study was conducted to evaluate the potential for secondary organic aerosol formation from emissions from automotive exhaust. The goal was to determine to what extent photochemical oxidation products of these hydrocarbons contribute to secondary organic aerosol (SO...

A metal-free electrocatalyst for carbon dioxide reduction to multi-carbon hydrocarbons and oxygenates

PubMed Central

Wu, Jingjie; Ma, Sichao; Sun, Jing; Gold, Jake I.; Tiwary, ChandraSekhar; Kim, Byoungsu; Zhu, Lingyang; Chopra, Nitin; Odeh, Ihab N.; Vajtai, Robert; Yu, Aaron Z.; Luo, Raymond; Lou, Jun; Ding, Guqiao; Kenis, Paul J. A.; Ajayan, Pulickel M.

2016-01-01

Electroreduction of carbon dioxide into higher-energy liquid fuels and chemicals is a promising but challenging renewable energy conversion technology. Among the electrocatalysts screened so far for carbon dioxide reduction, which includes metals, alloys, organometallics, layered materials and carbon nanostructures, only copper exhibits selectivity towards formation of hydrocarbons and multi-carbon oxygenates at fairly high efficiencies, whereas most others favour production of carbon monoxide or formate. Here we report that nanometre-size N-doped graphene quantum dots (NGQDs) catalyse the electrochemical reduction of carbon dioxide into multi-carbon hydrocarbons and oxygenates at high Faradaic efficiencies, high current densities and low overpotentials. The NGQDs show a high total Faradaic efficiency of carbon dioxide reduction of up to 90%, with selectivity for ethylene and ethanol conversions reaching 45%. The C2 and C3 product distribution and production rate for NGQD-catalysed carbon dioxide reduction is comparable to those obtained with copper nanoparticle-based electrocatalysts. PMID:27958290

DOE Office of Scientific and Technical Information (OSTI.GOV)

Striolo, Alberto; Cole, David R.

Because of a number of technological advancements, unconventional hydrocarbons, and in particular shale gas, have transformed the US economy. Much is being learned, as demonstrated by the reduced cost of extracting shale gas in the US over the past five years. However, a number of challenges still need to be addressed. Many of these challenges represent grand scientific and technological tasks, overcoming which will have a number of positive impacts, ranging from the reduction of the environmental footprint of shale gas production to improvements and leaps forward in diverse sectors, including chemical manufacturing and catalytic transformations. This review addresses recentmore » advancements in computational and experimental approaches, which led to improved understanding of, in particular, structure and transport of fluids, including hydrocarbons, electrolytes, water, and CO 2 in heterogeneous subsurface rocks such as those typically found in shale formations. Finally, the narrative is concluded with a suggestion of a few research directions that, by synergistically combining computational and experimental advances, could allow us to overcome some of the hurdles that currently hinder the production of hydrocarbons from shale formations.« less

Geoelectrical investigation of oil contaminated soils in former underground fuel base: Borne Sulinowo, NW Poland

NASA Astrophysics Data System (ADS)

Zogala, B.; Dubiel, R.; Zuberek, W. M.; Rusin-Zogala, M.; Steininger, M.

2009-07-01

The survey has been carried out in the area of 0.23 km2 of the former military underground fuel base. The oil derivative products were observed in excavations and the laboratory tests confirmed the occurrence of hydrocarbons (>C12) in soils. The purpose of the survey was to determine the spatial extent of the contamination. The studied area is covered by postglacial sediments: sands, gravels and till. The first water table was observed at a depth of 10-12 m. The detailed electromagnetic measurements with Geonics EM31-MK2 conductivity meter were performed in the whole area of the former fuel base. Obtained results were elaborated statistically and the map of apparent electrical conductivity to a depth of 6 m was created. Many local low conductivity anomalies were observed. The measurements with Geonics EM34-3XL were performed along one A-A' profile and 1D electromagnetic modelling along with this profile was calculated to obtain the electrical conductivity cross-section to a depth of 30 m. Two-dimensional electrical resistivity imaging measurements were carried out along the same profile and the resistivity cross-section to a depth of 20 m was performed. Both conducivity and resistivity cross-sections show anomalous zones. The zones correlate with oil contaminated zones very well.

Remote Sensing Detecting for Hydrocarbon Microseepage and Relationship with the Uranium Mineralization in Dongsheng Area, Ordos Basin, China

NASA Astrophysics Data System (ADS)

Zhu, M.; Liu, D.; Gao, Y.

2005-12-01

The Ordos Basin is located at the central area of northern China with an area of about 250,000 km2. It is well known "a basin of energy resources" of China for its large reserves of coal, oil and gas. A large-scale sandstone-type uranium metallogenic belt has been found recently in Zhiluo Formation of middle Jurassic in Dongsheng area in the northeastern part of the basin. The ore-forming mechanism remains unsolved so far. There is a hypothesis that the uranium precipitation was related to a hydrocarbon migration from the central basin. In order to explore the evidences of ever existed hydrocarbon microseepage and migration in this area, several indices such as the Iron Oxide Index, Ferrous Index, Clay Mineral Index, Mineral Composite Index, and Ferrous Transfer Percentage Index have been derived. Thorium Normalization of aeroradiometric data and fusion of aeroradiometric and TM data have been carried out as well. Therefore, the subaerial oxide and reduced area, uranium outmigrated and immigrated area, and ancient recharge and discharge of groundwater are thus delineated. As a result, two hydrocarbon microseepage belts in Dongsheng area have been extracted by combining the methods mentioned above. One is in the northern of Dongsheng along a nearly east-westward fault zone and the other one is in the southern of Dongsheng uranium mineralization belt along a nearly northwestward fault zone. The study suggests that the subaerial reduced area was related to hydrocarbon microseepage and the hydrocarbon migration along the fault and fracture zone or penetrable strata played an important role for uranium deposition in Zhiluo Formation near the northwestward fault zone.

Time Course-Dependent Methanogenic Crude Oil Biodegradation: Dynamics of Fumarate Addition Metabolites, Biodegradative Genes, and Microbial Community Composition

PubMed Central

Toth, Courtney R. A.; Gieg, Lisa M.

2018-01-01

Biodegradation of crude oil in subsurface petroleum reservoirs has adversely impacted most of the world's oil, converting this resource to heavier forms that are of lower quality and more challenging to recover. Oil degradation in deep reservoir environments has been attributed to methanogenesis over geological time, yet our understanding of the processes and organisms mediating oil transformation in the absence of electron acceptors remains incomplete. Here, we sought to identify hydrocarbon activation mechanisms and reservoir-associated microorganisms that may have helped shape the formation of biodegraded oil by incubating oilfield produced water in the presence of light (°API = 32) or heavy crude oil (°API = 16). Over the course of 17 months, we conducted routine analytical (GC, GC-MS) and molecular (PCR/qPCR of assA and bssA genes, 16S rRNA gene sequencing) surveys to assess microbial community composition and activity changes over time. Over the incubation period, we detected the formation of transient hydrocarbon metabolites indicative of alkane and alkylbenzene addition to fumarate, corresponding with increases in methane production and fumarate addition gene abundance. Chemical and gene-based evidence of hydrocarbon biodegradation under methanogenic conditions was supported by the enrichment of hydrocarbon fermenters known to catalyze fumarate addition reactions (e.g., Desulfotomaculum, Smithella), along with syntrophic bacteria (Syntrophus), methanogenic archaea, and several candidate phyla (e.g., “Atribacteria”, “Cloacimonetes”). Our results reveal that fumarate addition is a possible mechanism for catalyzing the methanogenic biodegradation of susceptible saturates and aromatic hydrocarbons in crude oil, and we propose the roles of community members and candidate phyla in our cultures that may be involved in hydrocarbon transformation to methane in crude oil systems. PMID:29354103

Formation of Bimolecular Membranes from Lipid Monolayers and a Study of Their Electrical Properties

PubMed Central

Montal, M.; Mueller, P.

1972-01-01

Bimolecular membranes are formed from two lipid monolayers at an air-water interface by the apposition of their hydrocarbon chains when an aperture in a Teflon partition separating two aqueous phases is lowered through the interface. Formation of the membrane is monitored by an increase of the electrical capacity, as measured with a voltage clamp. Electrical resistance of the unmodified membrane is analogous to that of conventional planar bilayers (black lipid membranes) prepared in the presence of a hydrocarbon solvent, i.e., 106-108 ohm cm2; the resistance can be lowered to values of 103 ohm cm2 by gramicidin, an antibiotic that modifies the conductance only when the membranes are of biomolecular thickness. In contrast to the resistance, there is a significant difference between the capacity of bilayers made from mono-layers and that of hydrocarbon-containing bilayers made by phase transition; the average values are 0.9 and 0.45 μF cm-2, respectively. The value of 0.9 μF cm-2 approximates that of biological membranes. Assuming a dielectric constant of 2.1 for the hydrocarbon region, the dielectric thickness, as calculated from a capacity of 0.9 μF cm-2, is 22 Å. This value is 6-10 Å smaller than the actual thickness of the hydrocarbon region of bilayers and cell membranes, as determined by x-ray diffraction. The difference may be due to a limited penetration of water into the hydrocarbon region near the ester groups that would lower the electrical resistance of this region and reduce the dielectric thickness. Asymmetric membranes have been formed by adjoining two lipid monolayers of different chemical composition. Images PMID:4509315

Rock Magnetic Investigation of Soils and Sediments Overlying the Hydrocarbon-Bearing Silurian Pinnacle Reefs in the Michigan Basin

NASA Astrophysics Data System (ADS)

Smirnov, A. V.; Tresnak, J. P.; Anderson, K. L.

2017-12-01

Hydrocarbon reservoirs may be associated with significant magnetic anomalies arguably caused by diagenetic alteration of iron-bearing minerals in hydrocarbon seepage environments. However, complete understanding of the physical mechanisms and pathways of hydrocarbon-induced magnetic alteration requires a robust and representative observational database. In order to facilitate the fundamental understanding of the magnetic signature of hydrocarbons, we conducted an investigation of the relationship between the hydrocarbon migration and magnetic properties of sediments overlaying the oil-bearing formations of the Silurian northern pinnacle reef belt of the Michigan Basin. Several hundreds of near-surface soil and sediment samples were collected across several long transects across the trend of the Niagaran Reef System and represented areas both over and away from known hydrocarbon sources. The samples were investigated by a variety of microscopy and rock magnetic methods. Our data indicate that the relationship between the hydrocarbon reservoirs and low-field magnetic susceptibility over the Niagaran pinnacle reef belt in the Michigan Basin is not straightforward. Both very high and very low susceptibility values have been observed within the extent of the reef belt in the studied area. The observed magnetic susceptibility anomalies may reflect the hydrological gradients in the uppermost glaciofluvial aquifer. However, a good correlation with the Devonian hydrocarbon reservoirs outside of the reef belt indicates a potential of the surface magnetic susceptibility method for hydrocarbon detection at a smaller scale.

43 CFR 3480.0-1 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Federal coal; ensure production practices that prevent wasting or loss of coal or other resources; avoid unnecessary damage to coal-bearing or mineral-bearing formations; ensure MER of Federal coal; ensure that... regulation of surface and underground coal mining operations; require an accurate record and accounting of...

43 CFR 3480.0-1 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Federal coal; ensure production practices that prevent wasting or loss of coal or other resources; avoid unnecessary damage to coal-bearing or mineral-bearing formations; ensure MER of Federal coal; ensure that... regulation of surface and underground coal mining operations; require an accurate record and accounting of...

43 CFR 3480.0-1 - Purpose.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Federal coal; ensure production practices that prevent wasting or loss of coal or other resources; avoid unnecessary damage to coal-bearing or mineral-bearing formations; ensure MER of Federal coal; ensure that... regulation of surface and underground coal mining operations; require an accurate record and accounting of...

43 CFR 3480.0-1 - Purpose.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Federal coal; ensure production practices that prevent wasting or loss of coal or other resources; avoid unnecessary damage to coal-bearing or mineral-bearing formations; ensure MER of Federal coal; ensure that... regulation of surface and underground coal mining operations; require an accurate record and accounting of...

Caldera demonstration model

USGS Publications Warehouse

Venezky, Dina; Wessells, Stephen

2010-01-01

A caldera is a large, usually circular volcanic depression formed when magma is withdrawn or erupted from a shallow underground magma reservoir. It is often difficult to visualize how calderas form. This simple experiment using flour, a balloon, tubing, and a bicycle pump, provides a helpful visualization for caldera formation.

Use of synthetic sonic logs derived from seismic data in interpretation of stratigraphic variation in cretaceous carbonates of North field area, Qatar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aves, H.S.; Tappmeyer, D.M.

This study uses geologic and synthetic sonic sections to evaluate the hydrocarbon potential of the Lower and middle Cretaceous Thamama Group carbonates of the Mishrif, Nahr, Umr, Shuaiba, and Kharaib Formations in the North Field, Qatar. The North field area, a regional high throughout Lower and middle Cretaceous time, is document by depositional thinning and by higher energy carbonate facies development. Oil and gas accumulations are found on the crestal portions of this paleohigh in structural/stratigraphic traps. Three factors affect the interval velocities on both a regional and local basis. These are (1) variation of carbonate facies-higher energy wackestone/packstone andmore » possibly grainstones flanked by predominantly mudstones, (2) secondary porosity developed near the top of unconformity surfaces, and (3) the existence of hydrocarbons in the reservoir. Many local lateral and vertical variations in interval velocities were noted on the synthetic sonic sections that would have otherwise been undetected, such as areas of tight or porous reservoir development, permeability barriers, and subtle faulting. In these studied formations, there are many examples of low interval velocity zones that are known to contain hydrocarbons whereas equivalent higher interval velocity zones on the seismic sections at other well site locations do not contain hydrocarbons. In many places, these variations are of sufficient magnitude to be mapped as intraformational permeability barriers. These variations were useful in explaining the occurrence of different oil-water and gas-water contacts within the same formation that could not be explained solely on structural criteria.« less

Petroleum geology of the Southern Bida Basin, Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braide, S.P.

1990-05-01

The Southern Bida basin is located in central Nigeria and is a major sedimentary area with a 3.5-km-thick sedimentary fill. However, it is the least understood of Nigeria's sedimentary basins because serious oil and gas exploration has not been undertaken in the basin. The surrounding Precambrian basement rocks experienced severe deformation during the Late Panafrican phase (600 {plus minus} 150 m.y.), and developed megashears that were reactivated during the Late Campanian-Maestrichtian. The ensuing wrenchfault tectonics formed the basin. The sedimentary fill, which comprises the Lokoja Formation are chiefly, if not wholly, nonmarine clastics. These have been characterized into facies thatmore » rapidly change from basin margin to basin axis, and have undergone only relatively mild tectonic distortion. Subsurface relations of the Lokoja Formation are postulated from outcrop study. The potential source rocks are most likely within the basinal axis fill and have not been deeply buried based on vitrinite reflectance of <0.65%. These findings, with the largely nonmarine depositional environment, suggest gas and condensate are the most likely hydrocarbons. Alluvial fans and deltaic facies that interfinger with lacustrine facies provide excellent reservoir capabilities. Potential traps for hydrocarbon accumulation were formed by a northwest-southeast-trending Campanian-Maestrichtian wrench system with associated northeast-southwest-oriented normal faults. The traps include strata in alluvial fans, fractured uplifted basement blocks, and arched strata over uplifted blocks. However, the size of hydrocarbon accumulations could be limited to some extent by a lack of effective hydrocarbon seal, because the dominant seals in the formation are unconformities.« less

Deposit formation in hydrocarbon rocket fuels

NASA Technical Reports Server (NTRS)

Roback, R.; Szetela, E. J.; Spadaccini, L. J.

1981-01-01

An experimental program was conducted to study deposit formation in hydrocarbon fuels under flow conditions that exist in high-pressure, rocket engine cooling systems. A high pressure fuel coking test apparatus was designed and developed and was used to evaluate thermal decomposition (coking) limits and carbon deposition rates in heated copper tubes for two hydrocarbon rocket fuels, RP-1 and commercial-grade propane. Tests were also conducted using JP-7 and chemically-pure propane as being representative of more refined cuts of the baseline fuels. A parametric evaluation of fuel thermal stability was performed at pressures of 136 atm to 340 atm, bulk fuel velocities in the range 6 to 30 m/sec, and tube wall temperatures in the range 422 to 811 K. Results indicated that substantial deposit formation occurs with RP-1 fuel at wall temperatures between 600 and 800 K, with peak deposit formation occurring near 700 K. No improvements were obtained when deoxygenated JP-7 fuel was substituted for RP-1. The carbon deposition rates for the propane fuels were generally higher than those obtained for either of the kerosene fuels at any given wall temperature. There appeared to be little difference between commercial-grade and chemically-pure propane with regard to type and quantity of deposit. Results of tests conducted with RP-1 indicated that the rate of deposit formation increased slightly with pressure over the range 136 atm to 340 atm. Finally, lating the inside wall of the tubes with nickel was found to significantly reduce carbon deposition rates for RP-1 fuel.

Heterobimetallic Zeolite, InV-ZSM-5, Enables Efficient Conversion of Biomass Derived Ethanol to Renewable Hydrocarbons

PubMed Central

Narula, Chaitanya K.; Li, Zhenglong; Casbeer, Erik M.; Geiger, Robert A.; Moses-Debusk, Melanie; Keller, Martin; Buchanan, Michelle V.; Davison, Brian H.

2015-01-01

Direct catalytic conversion of ethanol to hydrocarbon blend-stock can increase biofuels use in current vehicles beyond the ethanol blend-wall of 10–15%. Literature reports describe quantitative conversion of ethanol over zeolite catalysts but high C2 hydrocarbon formation renders this approach unsuitable for commercialization. Furthermore, the prior mechanistic studies suggested that ethanol conversion involves endothermic dehydration step. Here, we report the complete conversion of ethanol to hydrocarbons over InV-ZSM-5 without added hydrogen and which produces lower C2 (<13%) as compared to that over H-ZSM-5. Experiments with C2H5OD and in situ DRIFT suggest that most of the products come from the hydrocarbon pool type mechanism and dehydration step is not necessary. Thus, our method of direct conversion of ethanol offers a pathway to produce suitable hydrocarbon blend-stock that may be blended at a refinery to produce fuels such as gasoline, diesel, JP-8, and jet fuel, or produce commodity chemicals such as BTX. PMID:26526963

Heterobimetallic zeolite, InV-ZSM-5, enables efficient conversion of biomass derived ethanol to renewable hydrocarbons

DOE PAGES

Narula, Chaitanya K.; Li, Zhenglong; Casbeer, Erik M.; ...

2015-11-03

Here, direct catalytic conversion of ethanol to hydrocarbon blend-stock can increase biofuels use in current vehicles beyond the ethanol blend-wall of 10–15%. Literature reports describe quantitative conversion of ethanol over zeolite catalysts but high C 2 hydrocarbon formation renders this approach unsuitable for commercialization. Furthermore, the prior mechanistic studies suggested that ethanol conversion involves endothermic dehydration step. Here, we report the complete conversion of ethanol to hydrocarbons over InV-ZSM-5 without added hydrogen and which produces lower C 2 (<13%) as compared to that over H-ZSM-5. Experiments with C 2H 5OD and in situ DRIFT suggest that most of the productsmore » come from the hydrocarbon pool type mechanism and dehydration step is not necessary. Thus, our method of direct conversion of ethanol offers a pathway to produce suitable hydrocarbon blend-stock that may be blended at a refinery to produce fuels such as gasoline, diesel, JP-8, and jet fuel, or produce commodity chemicals such as BTX.« less

LABORATORY AND COMPUTATIONAL INVESTIGATIONS OF THE ATMOSPHERIC CHEMISTRY OF KEY OXIDATION PRODUCTS CONTROLLING TROPOSPHERIC OZONE FORMATION

EPA Science Inventory

Major uncertainties remain in our ability to identify the key reactions and primary oxidation products of volatile hydrocarbons that contribute to ozone formation in the troposphere. To reduce these uncertainties, computational chemistry, mechanistic and process analysis techniqu...

Effects of groundwater on radionuclides buried at the Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, B.A.; Maestas, S.; Thompson, J.L.

A large fraction of the radioactive source from a nuclear test is confined to the cavity created by the event. A {open_quotes}melt glass{close_quotes} accumulates at the bottom of the cavity where the highest concentrations of refractory radionuclides (e.g., Zr-95, Eu-155, Pu-239) are found. Most of the movement of radionuclides underground at the Nevada Test Site occurs through the agency of moving groundwater. Results from samples that were taken from the cavity formed in 1981 by the underground test named Baseball indicate that radioactive materials have remained where they were deposited during the formation of the cavity and chimney. There maymore » not be a mechanism for radionuclides to migrate at this location due to small hydraulic gradients and a low hydraulic conductivity. The study done at this site offers further evidence that extensive migration of radioactive materials away from underground nuclear test sites does not occur in the absence of appreciable groundwater movement.« less

DEVELOPMENTAL EXPRESSION OF TWO MEMBERS OF A NEW CLASS OF TRANSCRIPTION FACTORS: II. EXPRESSION OF ARYL HYDROCARBON RECEPTOR NUCLEAR TRANSLOCATOR IN THE C57BL/6N MOUSE EMBRYO

EPA Science Inventory

The Aryl hydrocarbon receptor (AhR) is a ligand-activated, transcription factor with a basic region/helix (bHLH) motif. hR has been sequenced and the functional domains defined and there is information on the formation of complexes with other peptides and interactions with DNA, a...

Land subsidence associated with hydrocarbon production, Texas Gulf Coast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kreitler, C.W.; White, W.A.; Akhter, M.S.

1988-01-01

Although ground-water withdrawal has been the predominant cause of land subsidence in the Texas Gulf Coast, localized subsidence and faulting have also resulted from hydrocarbon production. Subsidence was documented as early as the 1920s over the Goose Creek field. Since then, subsidence and/or faulting have been identified over the Saxet, South Houston, Chocolate Bayou, Hastings, Alco-Mag, Clinton, Mykawa, Blue Ridge, Webster, and Caplen oil fields. Oil-production-related subsidence over these fields generally creates few environmental or engineering problems. One exception is the subsidence and faulting over the Caplen oil field on Bolivar Peninsula, where more than 1,000 ac of saltwater marshmore » has been replaced by subaqueous flats. Subsidence may be occurring over other fields but has not been identified because of limited releveled benchmark data. An evaluation of drill-stem and bottom-hole pressure data for the Frio Formation in Texas indicates extensive depressurization presumably from hydrocarbon production. Nearly 12,000 measurements from a pressure data base of 17,000 measurements indicate some depressurization. Some of the Frio zones have pressure declines of more than 1,500 psi from original hydrostatic conditions. Subsidence and faulting may be associated with these fields in the Frio as well as other Tertiary formations where extensive hydrocarbon production and subsequent depressurization have occurred.« less

Optimization of Enterobacter cloacae (KU923381) for diesel oil degradation using response surface methodology (RSM).

PubMed

Ramasamy, Sugumar; Arumugam, Arumugam; Chandran, Preethy

2017-02-01

Efficiency of Enterobacter cloacae KU923381 isolated from petroleum hydrocarbon contaminated soil was evaluated in batch culture and bioreactor mode. The isolate were screened for biofilm formation using qualitative and quantitative assays. Response surface methodology (RSM) was used to study the effect of pH, temperature, glucose concentration, and sodium chloride on diesel degradation. The predicted values for diesel oil degradation efficiency by the statistical designs are in a close agreement with experimental data (R 2 = 99.66%). Degradation efficiency is increased by 36.78% at pH = 7, temperature = 35°C, glucose = 5%, and sodium chloride concentration = 5%. Under the optimized conditions, the experiments were performed for diesel oil degradation by gas chromatographic mass spectrometric analysis (GC-MS). GC-MS analysis confirmed that E. cloacae had highly degrade hexadecane, heptadecane, tridecane, and docosane by 99.71%, 99.23%, 99.66%, and 98.34% respectively. This study shows that rapid bioremoval of hydrocarbons in diesel oil is acheived by E. cloacae with abet of biofilm formation. The potential use of the biofilms for preparing trickling filters (gravel particles) for the degradation of hydrocarbons from petroleum wastes before their disposal in the open environment is highly suggested. This is the first successful attempt for artificially establishing petroleum hydrocarbon degrading bacterial biofilm on solid substrates in bioreactor.

An interpretation of core and wireline logs for the Petrophysical evaluation of Upper Shallow Marine sandstone reservoirs of the Bredasdorp Basin, offshore South Africa

NASA Astrophysics Data System (ADS)

Magoba, Moses; Opuwari, Mimonitu

2017-04-01

This paper embodies a study carried out to assess the Petrophysical evaluation of upper shallow marine sandstone reservoir of 10 selected wells in the Bredasdorp basin, offshore, South Africa. The studied wells were selected randomly across the upper shallow marine formation with the purpose of conducting a regional study to assess the difference in reservoir properties across the formation. The data sets used in this study were geophysical wireline logs, Conventional core analysis and geological well completion report. The physical rock properties, for example, lithology, fluid type, and hydrocarbon bearing zone were qualitatively characterized while different parameters such as volume of clay, porosity, permeability, water saturation ,hydrocarbon saturation, storage and flow capacity were quantitatively estimated. The quantitative results were calibrated with the core data. The upper shallow marine reservoirs were penetrated at different depth ranging from shallow depth of about 2442m to 3715m. The average volume of clay, average effective porosity, average water saturation, hydrocarbon saturation and permeability range from 8.6%- 43%, 9%- 16%, 12%- 68% , 32%- 87.8% and 0.093mD -151.8mD respectively. The estimated rock properties indicate a good reservoir quality. Storage and flow capacity results presented a fair to good distribution of hydrocarbon flow.

One-step hydroprocessing of fatty acids into renewable aromatic hydrocarbons over Ni/HZSM-5: insights into the major reaction pathways.

PubMed

Xing, Shiyou; Lv, Pengmei; Wang, Jiayan; Fu, Junying; Fan, Pei; Yang, Lingmei; Yang, Gaixiu; Yuan, Zhenhong; Chen, Yong

2017-01-25

For high caloricity and stability in bio-aviation fuels, a certain content of aromatic hydrocarbons (AHCs, 8-25 wt%) is crucial. Fatty acids, obtained from waste or inedible oils, are a renewable and economic feedstock for AHC production. Considerable amounts of AHCs, up to 64.61 wt%, were produced through the one-step hydroprocessing of fatty acids over Ni/HZSM-5 catalysts. Hydrogenation, hydrocracking, and aromatization constituted the principal AHC formation processes. At a lower temperature, fatty acids were first hydrosaturated and then hydrodeoxygenated at metal sites to form long-chain hydrocarbons. Alternatively, the unsaturated fatty acids could be directly deoxygenated at acid sites without first being saturated. The long-chain hydrocarbons were cracked into gases such as ethane, propane, and C 6 -C 8 olefins over the catalysts' Brønsted acid sites; these underwent Diels-Alder reactions on the catalysts' Lewis acid sites to form AHCs. C 6 -C 8 olefins were determined as critical intermediates for AHC formation. As the Ni content in the catalyst increased, the Brønsted-acid site density was reduced due to coverage by the metal nanoparticles. Good performance was achieved with a loading of 10 wt% Ni, where the Ni nanoparticles exhibited a polyhedral morphology which exposed more active sites for aromatization.

Review of current results in computational studies of hydrocarbon phase and transport properties in nanoporous structures

NASA Astrophysics Data System (ADS)

Stroev, N.; Myasnikov, A.

2017-12-01

This article provides a general overview of the main simulation results on the behavior of gas/liquids under confinement conditions, namely hydrocarbons in shale formations, and current understanding of such phenomena. In addition to the key effects, which different research groups obtained and which have to be taken into account during the creation of reservoir simulation software, a list of methods is briefly covered. Comprehensive understanding of both fluid phase equilibrium and transport properties in nanoscale structures is of great importance for many scientific and technical disciplines, especially for petroleum engineering considering the hydrocarbon behavior in complex shale formations, the development of which increases with time. Recent estimations show that a significant amount of resources are trapped inside organic matter and clays, which has extremely low permeability and yet great economic potential. The issue is not only of practical importance, as the existing conventional approaches by definition are unable to capture complicated physics phenomena for effective results, but it is also of fundamental value. The research of the processes connected with such deposits is necessary for both evaluations of petroleum reservoir deposits and hydrodynamic simulators. That is why the review is divided into two major parts—equilibrium states of hydrocarbons and their transport properties in highly confined conditions.

Studies of soil and ecohydrological processes in oil-gas production regions.

NASA Astrophysics Data System (ADS)

Khodyreva, E. Ya.; Khodyrev, Yu. P.

2009-04-01

For a better understanding and describing of the functional interactions between processes in soil and drinking, underground and stratum waters in oil-gas production regions we used laboratory and field monitoring methods of studies. The control of ecological situation dynamics in oil-gas production regions proposes a presence of primary data about parameter-indicators, which characterize a state of the object under investigation. One of these parameters is the concentration of heavy metal salts in drinking and stratum waters. Isolation of some compounds, which are extracted as impurities of oil and water during recovery of hydrocarbons from productive horizons, would enhance profitableness of recovery. Because accompanying impurities are a mixture of different salts and complexes, the methods of multielement analysis give the most objective evaluation of total content of some elements by search and prospecting. The developed method of laser mass-spectrometric analysis of oil and drinking, underground and industrial waters allows to investigate the samples on all elements of the periodical system simultaneously with limit sensitivity 0.1 mkg/l. The preparation of the oil and water probes was carried out by sublimation of highly volatile fractions in vacuum at 100 0C. The samples of drinking and underground waters, oils and industrial waters from wells of oil field Romashkin (Tatarstan) were chosen as the object for the research. In respect to possible metal extraction scandium is of most interest in inspected area because it's very high cost and availability of water-soluble pattern, most probably chloride. Its concentration in one well was 1 mg/l in water and 0.01 mg/l in oil. According to the received data of laser mass-spectrometric analysis, industrial waters on the activity investigated territory joint-stock company "Tatneft" contain 220-330 kg / ton of salts of metals that does by their potential source of alternative raw material for the chemical industry. Soil is an important component of the earth's biosphere because of its crucial role in the hydrological cycle. For revealing possible correlation between spatial distributions of the valuable elements contained both in industrial waters and in tests of soils, 79 samples are prepared and investigated. These tests are selected at superficial geochemical shooting (field monitoring methods of studies) Aznakaevskoi, Karamalinskoi and Sabanchinskoi areas of joint-stock company " Tatneft ". Circuits of distribution of valuable elements on the investigated territory are constructed also a quantitative estimation of the maintenance makro- and microcomponents is given. From the found out elements the greatest interest Na, Mg, K, Ca, Cl, Br and their connections represent because of very high concentration and scandium owing to the cost. Now cost of scandium in the world market approximately in 25 times exceeds cost of gold and is not observed yet tendencies to its decrease. Presence of impurity of salts of heavy metals and their connections in soils, drinking, underground and stratum waters, definition of their concentration and comparison from maximum concentration limit allows to establish the control over dynamics of ecohydrological conditions and in due time to take measures on reduction of negative influence of processes of development of hydrocarbon raw material by an environment.

Gum and deposit formation from jet-turbine and diesel fuels at 100 C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayo, F.R.; Lan, B.Y.

1987-01-01

Rates of oxidation and gum formation for six hydrocarbons, three jet-turbine fuels and three diesel fuels have been measured at 100 C in the presence of t-Bu2O2 tert-butyl-peroxide as initiator. Four of six fuels oxidize faster at 100 C than in previous work at 130 C with initiator. Four any single substrate, the amount of gum produced for the oxygen absorbed is similar at 100 and 130 C even with large changes in rates and t-Bu2O2 concentrations. Thus, one mechanism of gum formation is intimately associated with oxidation. The effects of t-Bu2O2 concentration on the rates of oxygen absorption andmore » gum formation show that gum formation is associated with chain termination by two peroxy radicals. In general, the pure hydrocarbons have long kinetic chains and give good yields of hydroperoxides. The fuels give short kinetic chains and produce little hydroperoxide but but much more gum formation is the coupling of substrates by peroxides in the absence of oxygen. The mechanism, condensation of oxidation products from alkylnaphthalenes, is also proposed.« less

Initial development and performance evaluation of a process for formation of dense carbon by pyrolysis of methane

NASA Technical Reports Server (NTRS)

Noyes, G. P.; Cusick, R. J.

1985-01-01

The three steps in pyrolytic carbon formation are: (1) gaseous hydrocarbon polymerization and aromatic formation; (2) gas-phase condensation and surface adsorption/impingement of polyaromatic hydrocarbon; and (3) final dehydration to carbon. The structure of the carbon in the various stages of formation is examined. The apparatuses and experimental procedures for the pyrolysis of methane in a 60 cm long quartz reactor tube at temperatures ranging from 1400-1600 K are described. The percentage of carbon converted and its density are calculated and tabularly presented. The results reveal that dense carbon formation is maximized and soot eliminated by this procedure. It is observed that conversion efficiency depends on the composition of the inlet gas and conversion increases with increasing temperature. Based on the experimental data a three-man carbon reactor subsystem (CRS) is developed; the functions of the Sabatier Methanation Reactor, two carbon formation reactors and fluid handling components of the CRS are analyzed. The CRS forms 16 kg of carbon at a rate of 0.8 kg/day for 20 days in a two percent volume density quartz wool packing at temperature of 1500-1600 K.

78 FR 38704 - Mississippi Hub, LLC; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-27

... finished drilling the injection and withdrawal wells for Cavern 3 and is presently leaching the underground salt formation. The proposed increase in capacity will entail continued leaching of Cavern 3 to reach the proposed new capacity levels. The activity will be completed using the existing leaching...

Symbiont-driven sulfur crystal formation in a thiotrophic symbiosis from deep-sea hydrocarbon seeps

PubMed Central

Eichinger, Irmgard; Schmitz-Esser, Stephan; Schmid, Markus; Fisher, Charles R; Bright, Monika

2014-01-01

The siboglinid tubeworm Sclerolinum contortum symbiosis inhabits sulfidic sediments at deep-sea hydrocarbon seeps in the Gulf of Mexico. A single symbiont phylotype in the symbiont-housing organ is inferred from phylogenetic analyses of the 16S ribosomal ribonucleic acid (16S rRNA) gene and fluorescent in situ hybridization. The phylotype we studied here, and a previous study from an arctic hydrocarbon seep population, reveal identical 16S rRNA symbiont gene sequences. While sulfide is apparently the energy source for the symbionts (and ultimately the gutless host), both partners also have to cope with its toxicity. This study demonstrates abundant large sulfur crystals restricted to the trophosome area. Based on Raman microspectroscopy and energy dispersive X-ray analysis, these crystals have the same S8 sulfur configuration as the recently described small sulfur vesicles formed in the symbionts. The crystals reside adjacent to the symbionts in the trophosome. This suggests that their formation is either extra- or intracellular in symbionts. We propose that formation of these crystals provides both energy-storage compounds for the symbionts and serves the symbiosis by removing excess toxic sulfide from host tissues. This symbiont-mediated sulfide detoxification may have been crucial for the establishment of thiotrophic symbiosis and continues to remain an important function of the symbionts. PMID:24992535

Plowshare Program - American Atomic Bomb Tests For Industrial Applications

ScienceCinema

None

2018-01-16

The United States Atomic Energy Commission (AEC) established the Plowshare Program as a research and development activity to explore the technical and economic feasibility of using nuclear explosives for industrial applications. The reasoning was that the relatively inexpensive energy available from nuclear explosions could prove useful for a wide variety of peaceful purposes. The Plowshare Program began in 1958 and continued through 1975. Between December 1961 and May 1973, the United States conducted 27 Plowshare nuclear explosive tests comprising 35 individual detonations. Conceptually, industrial applications resulting from the use of nuclear explosives could be divided into two broad categories: 1) large-scale excavation and quarrying, where the energy from the explosion was used to break up and/or move rock; and 2) underground engineering, where the energy released from deeply buried nuclear explosives increased the permeability and porosity of the rock by massive breaking and fracturing. Possible excavation applications included: canals, harbors, highway and railroad cuts through mountains, open pit mining, construction of dams, and other quarry and construction-related projects. Underground nuclear explosion applications included: stimulation of natural gas production, preparation of leachable ore bodies for in situ leaching, creation of underground zones of fractured oil shale for in situ retorting, and formation of underground natural gas and petroleum storage reservoirs.

Morpho-anatomical features of underground systems in six Asteraceae species from the Brazilian Cerrado.

PubMed

Appezzato-da-Glória, Beatriz; Cury, Graziela

2011-09-01

In the Brazilian Cerrado (neotropical savanna), the development of bud-bearing underground systems as adaptive structures to fire and dry periods can comprise an important source of buds for this ecosystem, as already demonstrated in the Brazilian Campos grasslands and North American prairies. Asteraceae species from both woody and herbaceous strata have subterranean organs that accumulate carbohydrates, reinforcing the adaptive strategy of these plants to different environmental conditions. This study aims to analyse the morpho-anatomy of underground systems of six species of Asteraceae (Mikania cordifolia L.f. Willd., Mikania sessilifolia DC, Trixis nobilis (Vell.) Katinas, Pterocaulon alopecuroides (Lam.) DC., Vernonia elegans Gardner and Vernonia megapotamica Spreng.), to describe these structures and to verify the occurrence and origin of shoot buds, and to analyse the presence of reserve substances. Individuals sampled in Cerrado areas in São Paulo State showed thick underground bud-bearing organs, with adventitious or lateral roots and presence of fructans. Xylopodium was found in all studied species, except for Trixis nobilis, which had stem tuber. The presence of fructans as reserve, and the capacity of structures in the formation of buds indicate the potential of herbaceous species of Asteraceae in forming a viable bud bank for vegetation regeneration in the Brazilian Cerrado.

Plowshare Program - American Atomic Bomb Tests For Industrial Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2012-04-22

The United States Atomic Energy Commission (AEC) established the Plowshare Program as a research and development activity to explore the technical and economic feasibility of using nuclear explosives for industrial applications. The reasoning was that the relatively inexpensive energy available from nuclear explosions could prove useful for a wide variety of peaceful purposes. The Plowshare Program began in 1958 and continued through 1975. Between December 1961 and May 1973, the United States conducted 27 Plowshare nuclear explosive tests comprising 35 individual detonations. Conceptually, industrial applications resulting from the use of nuclear explosives could be divided into two broad categories: 1)more » large-scale excavation and quarrying, where the energy from the explosion was used to break up and/or move rock; and 2) underground engineering, where the energy released from deeply buried nuclear explosives increased the permeability and porosity of the rock by massive breaking and fracturing. Possible excavation applications included: canals, harbors, highway and railroad cuts through mountains, open pit mining, construction of dams, and other quarry and construction-related projects. Underground nuclear explosion applications included: stimulation of natural gas production, preparation of leachable ore bodies for in situ leaching, creation of underground zones of fractured oil shale for in situ retorting, and formation of underground natural gas and petroleum storage reservoirs.« less

Elucidating Environmental Fingerprinting Mechanisms of Unconventional Gas Development through Hydrocarbon Analysis.

PubMed

Piotrowski, Paulina K; Weggler, Benedikt A; Yoxtheimer, David A; Kelly, Christina N; Barth-Naftilan, Erica; Saiers, James E; Dorman, Frank L

2018-04-17

Hydraulic fracturing is an increasingly common technique for the extraction of natural gas entrapped in shale formations. This technique has been highly criticized due to the possibility of environmental contamination, underscoring the need for method development to identify chemical factors that could be utilized in point-source identification of environmental contamination events. Here, we utilize comprehensive two-dimensional gas chromatography (GC × GC) coupled to high-resolution time-of-flight (HRT) mass spectrometry, which offers a unique instrumental combination allowing for petroleomics hydrocarbon fingerprinting. Four flowback fluids from Marcellus shale gas wells in geographic proximity were analyzed for differentiating factors that could be exploited in environmental forensics investigations of shale gas impacts. Kendrick mass defect (KMD) plots of these flowback fluids illustrated well-to-well differences in heteroatomic substituted hydrocarbons, while GC × GC separations showed variance in cyclic hydrocarbons and polyaromatic hydrocarbons among the four wells. Additionally, generating plots that combine GC × GC separation with KMD established a novel data-rich visualization technique that further differentiated the samples.

Experimentally Determined Binding Energies of Astrophysically Relevant Hydrocarbons in Pure and H2O-Layered Ices

NASA Astrophysics Data System (ADS)

Behmard, Aida; Graninger, Dawn; Fayolle, Edith; Oberg, Karin I.

2017-01-01

Small hydrocarbons represent an important organic reservoir in a variety of interstellar environments. Constraints on desorption temperatures and binding energies of hydrocarbons are thus necessary for accurate predictions of where and in which phase these molecules exist. Through a series of temperature programmed desorption experiments, we determined binding energies of 1, 2, and 3-carbon interstellar hydrocarbons (CH4, C2H2, C2H4, C2H6, C3H4, C3H6, and C3H8) in pure ices and in relation to water ice, the dominant ice constituent during star and planet formation. These empirically determined values can be used to inform observations and models of the molecular spatial distribution in protoplanetary disks, thus providing insight into planetesimal composition. In addition, knowledge of hydrocarbon binding energies will refine simulations of grain surface chemistry, allowing for better predictions of the chemical conditions that lead to the production of complex organic molecules vital for life.

Process for recovering hydrocarbons from hydrocarbon-containing biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dzadzic, P.M.; Price, M.C.; Shih, C.J.

1982-07-06

A process is disclosed for enzymatically converting whole plant biomass containing hydrocarbon-containing laticifers to soluble sugars and recovering hydrocarbons in increased yields. The process comprises hydrolyzing whole plant cellulosic material in the presence of enzymes, particularly cellulase, hemicellulase, and pectinase, to produce a hydrocarbon product and recovering from the hydrolysis products a major proportion of the cellulase, hemicellulase and pectinase enzymes for reuse. At least some portion of the required make-up of cellulase, hemicellulase and pectinase enzymes is produced in a two-stage operation wherein, in the first stage, a portion of the output sugar solution is used to grow enzymemore » secreting microorganisms selected from the group consisting of cellulase-secreting microorganisms, hemicellulase-secreting microorganisms, pectinase-secreting microorganisms, and mixtures thereof, and in the second stage, cellulase, hemicellulase and pectinase enzyme formation is induced in the microorganism-containing culture medium by the addition of an appropriate inducer such as biomass. The cellulase, hemicellulase and pectinase enzymes are then recycled for use in the hydrolysis reaction.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yang; Kidder, Michelle; Ruther, Rose E.

In this paper, we present a new class of catalysts, InMo-ZSM- 5, which can be prepared by indium impregnation of Mo-ZSM- 5. The incorporation of indium dramatically decreases coke formation during methane dehydroaromatization. The benzene and C 2 hydrocarbons selectivity among total hydrocarbons over InMo-ZSM- 5 remains comparable to that of Mo-ZSM- 5 despite reduced methane conversion due to decreased coke formation. We found 1 wt% indium to be optimal loading for reducing coke selectivity to half that of Mo-ZSM- 5. Characterization methods were not helpful in discerning the interaction of In with Mo but experiments with bimetallic 1In2Mo-ZSM- 5more » and mechanical mixture 1In+2Mo-ZSM- 5 suggest that In and Mo need to be in close proximity to suppress coke formation. Finally, this is supported by temperature programmed reduction experiments which show that In incorporation leads to lower Mo reduction temperature in In2Mo-ZMS- 5.« less

Studies of elasticity, sound propagation and attenuation of acoustic modes in granular media: final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Makse, Hernan A.; Johnson, David L.

2014-09-03

This is the final report describing the results of DOE Grant # DE-FG02-03ER15458 with original termination date of April 31, 2013, which has been extended to April 31, 2014. The goal of this project is to develop a theoretical and experimental understanding of sound propagation, elasticity and dissipation in granular materials. The topic is relevant for the efficient production of hydrocarbon and for identifying and characterizing the underground formation for storage of either CO 2 or nuclear waste material. Furthermore, understanding the basic properties of acoustic propagation in granular media is of importance not only to the energy industry, butmore » also to the pharmaceutical, chemical and agricultural industries. We employ a set of experimental, theoretical and computational tools to develop a study of acoustics and dissipation in granular media. These include the concept effective mass of granular media, normal modes analysis, statistical mechanics frameworks and numerical simulations based on Discrete Element Methods. Effective mass measurements allow us to study the mechanisms of the elastic response and attenuation of acoustic modes in granular media. We perform experiments and simulations under varying conditions, including humidity and vacuum, and different interparticle force-laws to develop a fundamental understanding of the mechanisms of damping and acoustic propagation in granular media. A theoretical statistical approach studies the necessary phase space of configurations in pressure, volume fraction to classify granular materials.« less

Tectonosedimentary framework of Upper Cretaceous -Neogene series in the Gulf of Tunis inferred from subsurface data: implications for petroleum exploration

NASA Astrophysics Data System (ADS)

Dhraief, Wissem; Dhahri, Ferid; Chalwati, Imen; Boukadi, Noureddine

2017-04-01

The objective and the main contribution of this issue are dedicated to using subsurface data to delineate a basin beneath the Gulf of Tunis and its neighbouring areas, and to investigate the potential of this area in terms of hydrocarbon resources. Available well data provided information about the subsurface geology beneath the Gulf of Tunis. 2D seismic data allowed delineation of the basin shape, strata geometries, and some potential promising subsurface structures in terms of hydrocarbon accumulation. Together with lithostratigraphic data obtained from drilled wells, seismic data permitted the construction of isochron and isobath maps of Upper Cretaceous-Neogene strata. Structural and lithostratigraphic interpretations indicate that the area is tectonically complex, and they highlight the tectonic control of strata deposition during the Cretaceous and Neogene. Tectonic activity related to the geodynamic evolution of the northern African margin appears to have been responsible for several thickness and facies variations, and to have played a significant role in the establishment and evolution of petroleum systems in northeastern Tunisia. As for petroleum systems in the basin, the Cretaceous series of the Bahloul, Mouelha and Fahdene formations are acknowledged to be the main source rocks. In addition, potential reservoirs (Fractured Abiod and Bou Dabbous carbonated formations) sealed by shaly and marly formations (Haria and Souar formations respectively) show favourable geometries of trap structures (anticlines, tilted blocks, unconformities, etc.) which make this area adequate for hydrocarbon accumulations.

18 CFR 806.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... water supply. A system, including facilities for collection, treatment, storage and distribution, that... extraction of gaseous hydrocarbons from low permeability geologic formations utilizing enhanced drilling...

18 CFR 806.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... water supply. A system, including facilities for collection, treatment, storage and distribution, that... extraction of gaseous hydrocarbons from low permeability geologic formations utilizing enhanced drilling...

18 CFR 806.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... water supply. A system, including facilities for collection, treatment, storage and distribution, that... extraction of gaseous hydrocarbons from low permeability geologic formations utilizing enhanced drilling...

Influence of the Reaction Temperature on the Nature of the Active and Deactivating Species During Methanol-to-Olefins Conversion over H-SAPO-34

PubMed Central

2017-01-01

The selectivity toward lower olefins during the methanol-to-olefins conversion over H-SAPO-34 at reaction temperatures between 573 and 773 K has been studied with a combination of operando UV–vis diffuse reflectance spectroscopy and online gas chromatography. It was found that the selectivity toward propylene increases in the temperature range of 573–623 K, while it decreases in the temperature range of 623–773 K. The high degree of incorporation of olefins, mainly propylene, into the hydrocarbon pool affects the product selectivity at lower reaction temperatures. The nature and dynamics of the active and deactivating hydrocarbon species with increasing reaction temperature were revealed by a non-negative matrix factorization of the time-resolved operando UV–vis diffuse reflectance spectra. The active hydrocarbon pool species consist of mainly highly methylated benzene carbocations at temperatures between 573 and 598 K, of both highly methylated benzene carbocations and methylated naphthalene carbocations at 623 K, and of only methylated naphthalene carbocations at temperatures between 673 and 773 K. The operando spectroscopy results suggest that the nature of the active species also influences the olefin selectivity. In fact, monoenylic and highly methylated benzene carbocations are more selective to the formation of propylene, whereas the formation of the group of low methylated benzene carbocations and methylated naphthalene carbocations at higher reaction temperatures (i.e., 673 and 773 K) favors the formation of ethylene. At reaction temperatures between 573 and 623 K, catalyst deactivation is caused by the gradual filling of the micropores with methylated naphthalene carbocations, while between 623 and 773 K the formation of neutral poly aromatics and phenanthrene/anthracene carbocations are mainly responsible for catalyst deactivation, their respective contribution increasing with increasing reaction temperature. Methanol pulse experiments at different temperatures demonstrate the dynamics between methylated benzene and methylated naphthalene carbocations. It was found that methylated naphthalene carbocations species are deactivating and block the micropores at low reaction temperatures, while acting as the active species at higher reaction temperatures, although they give rise to the formation of extended hydrocarbon deposits. PMID:28824823

Influence of stratigraphic factors on the failure mechanisms of sinkholes related to man-made underground caves at Cutrofiano (South-Eastern Italy)

NASA Astrophysics Data System (ADS)

Lollino, Piernicola; Margiotta, Stefano; Parise, Mario

2013-04-01

An increasing number of areas in southern Italy are being interested by sinkholes related to the presence of man-made cavities, with underground quarries representing the more problematic typology of anthropogenic caves in terms of instability. The case of Cutrofiano (Apulia, SE Italy) is here presented as a representative case study. This territory is well known for the underground quarrying activity of soft calcarenitic rocks that caused in the last decades widespread phenomena of subsidence at the surface, with extensive damage and problems to the main communication routes in the area. A very complex and intricate network of subterranean galleries is present underground, for a total development on the order of several tens of kilometres. The Gravina Calcarenite Formation, that is the object of the underground quarries, consists of whitish calcarenite with an upper greenish clayey-sandy interval rich in fossils. This formation is overlain by grey sandy clays (Subapennine Clays) grading upward to fossil-rich sands (Brindisi Sands). In recent years, clay mining has been resumed at the ground surface, following the opening of a cement factory, and resulting in the realization of wide open-pit quarries. The local sedimentary sequence is closed by terraced calcarenite deposits, that holds a phreatic groundwater body. The results of detailed geological, geomorphological and geomechanical surveys, supported by laboratory tests, show that in the Cutrofiano area the thickness of the stratigraphical succession, the depth of the underground galleries, the structural conditions of the rock mass, and the failure mechanisms observed within the quarries are variable. The geological model reconstructed represents the base for the implementation of numerical simulations, which are aimed at defining the eventual mechanisms of rock failure, up to the formation of the sinkhole. Local changes in the stratigraphy are very common in the area, due to the overall slight attitude of the strata, dipping toward the SW, and to lateral variations in the geological succession. Thus, at least two different geological settings may be recognized: the first is typical of those areas closest to the town, where the calcarenite rock mass is at low depth, and appears to be covered by very thin deposits; in such a situation, the underground quarries develop at depths ranging from 7 to 10 meters below the ground surface. The second setting, which typically characterizes the sectors a few kilometres farther south, shows, on the other hand, the presence of thick cover of the clay-sandy intervals, and has the galleries of underground quarries located at depth variable from 15 to 45 m. Starting from these different situations, two-dimensional numerical analyses have been developed by using the finite element method to investigate the stress-strain evolution of the rock mass surrounding the galleries due to long-term degradation of the rock properties induced by weathering and water infiltration. The results obtained from the numerical simulations point out a quite different behaviour between the two geological settings, since the presence of the significant clay layer overlying the calcarenite substratum affects the geometry of the subsidence cone, and, consequently, the real extent of the likely sinkholes at the surface. These outcomes are of great importance to highlight the need to use detailed, site-specific, data in order to perform numerical modelling, and warn about the common habit of extending a small number of borehole data, tens of hundreds of meters apart, over large areas. Especially when carried out to define vulnerability and/or risk of specific elements at risk, the researches should be performed having available on-site data, or, alternatively, the end users should be properly warned in the use of the outcomes from the study.

Modeling the Impact of Deformation on Unstable Miscible Displacements in Porous Media

NASA Astrophysics Data System (ADS)

Santillán, D.; Cueto-Felgueroso, L.

2014-12-01

Coupled flow and geomechanics is a critical research challenge in engineering and the geosciences. The simultaneous flow of two or more fluids with different densities or viscosities through deformable media is ubiquitous in environmental, industrial, and biological processes, including the removal of non-aqueous phase liquids from underground water bodies, the geological storage of CO2, and current challenges in energy technologies, such as enhanced geothermal systems, unconventional hydrocarbon resources or enhanced oil recovery techniques. Using numerical simulation, we study the interplay between viscous-driven flow instabilities (viscous fingering) and rock mechanics, and elucidate the structure of the displacement patterns as a function of viscosity contrast, injection rate and rock mechanical properties. Finally, we discuss the role of medium deformation on transport and mixing processes in porous media.

Modeling the Impact of Fracture Growth on Fluid Displacements in Deformable Porous Media

NASA Astrophysics Data System (ADS)

Santillán, D.; Cueto-Felgueroso, L.; Juanes, R.

2015-12-01

Coupled flow and geomechanics is a critical research challenge in engineering and the geosciences. The flow of a fluid through a deformable porous media is present in manyenvironmental, industrial, and biological processes,such as the removal of pollutants from underground water bodies, enhanced geothermal systems, unconventional hydrocarbon resources or enhanced oil recovery techniques. However, the injection of a fluid can generate or propagate fractures, which are preferential flow paths. Using numerical simulation, we study the interplay between injection and rock mechanics, and elucidate fracture propagation as a function of injection rate, initial crack topology and mechanical rock properties. Finally, we discuss the role of fracture growth on fluid displacements in porous media. Figure: An example of fracture (in red) propagated in a porous media (in blue)

Preliminary report on the geology and underground water resources of the central Great Plains

USGS Publications Warehouse

Darton, N.H.

1905-01-01

The area to which this report relates is shown in Pl. II.  It comprises the greater portions of South Dakota, Nebraska, and Kansas, and the eastern portions of Colorado and of Wyoming, an area of about one-half million square miles. It is the result of my investigations during the past eight years, but includes also all available data from many sources. I have been aided by various field assistants, those deserving special mention being Messrs. C. A. Fisher, C. C. O'Harra, J.E. Todd, the late C. M. Hall, G. B. Eichardson, W. S. Tangier Smith, E. H. Barbour, and the late J. E. Macfarland.On account of its size, the region presents relatively diverse geologic conditions, but comprises comparatively few formations, most of which are widespread. The question of water supply, both overground and underground, is one of great interest to the people in this district, and although considerable progress has been made in some sections in developing well waters, there are vast areas in which the present supplies are inadequate, even for local domestic use. In order to understand the relations of the underground waters it has been necessary to investigate the geology, especially the structure and stratigraphy of the water-bearing and associated formations. This part of the work has required a very large amount of special field study, and the present results show that extended investigation will be required before many important questions of geology can be fully understood.

Timing of Hydrocarbon Fluid Emplacement in Sandstone Reservoirs in Neogene in Huizhou Sag, Southern China Sea, by Authigenic Illite 40Ar- 39Ar Laser Stepwise Heating

NASA Astrophysics Data System (ADS)

Hesheng, Shi; Junzhang, Zhu; Huaning, Qiu; yu, Shu; Jianyao, Wu; Zulie, Long

Timing of oil or gas emplacements is a new subject in isotopic geochronology and petroleum geology. Hamilton et al. expounded the principle of the illite K-Ar age: Illite is often the last or one of the latest mineral cements to form prior to hydrocarbon accumulation. Since the displacement of formation water by hydrocarbons will cause silicate diagenesis to cease, K-Ar ages for illite will constrain the timing of this event, and also constrain the maximum age of formation of the trap structure. In this study, the possibility of authigenic illites 40Ar- 39Ar dating has been investigated. The illite samples were separated from the Tertiary sandstones in three rich oil reservoir belts within the Huizhou sag by cleaning, fracturing by cycled cooling-heating, soxhlet-extraction with solvents of benzene and methanol and separating with centrifugal machine. If oil is present in the separated samples, ionized organic fragments with m/e ratios of 36 to 40 covering the argon isotopes will be yielded by the ion source of a mass spectrometer, resulting in wrong argon isotopic analyses and wrong 40Ar- 39Ar ages. The preliminary experiments of illite by heating did show the presence of ionized organic fragments with m/e ratios of 36 to 44. In order to clean up the organic gases completely and obtain reliable analysis results, a special purification apparatus has been established by Qiu et al. and proved valid by the sequent illite analyses. All the illite samples by 40Ar- 39Ar IR-laser stepwise heating yield stair-up age spectra in lower laser steps and plateaux in higher laser steps. The youngest apparent ages corresponding to the beginning steps are reasonable to be interpreted for the hydrocarbon accumulation ages. The weighted mean ages of the illites from the Zhuhai and Zhujiang Formations are (12.1 ± 1.1) Ma and (9.9 ± 1.2) Ma, respectively. Therefore, the critical emplacement of petroleum accumulation in Zhujiang Formation in Huizhou sag took place in ca 10 Ma. Late fault activity strengthened the entrance of hydrocarbon fluids into the oil systems based on the data of the studies of the fault evolvement history, petroleum system combinations, and homogeneous temperatures of fluid inclusions.

The Extreme Results of Climate Changes in Turkey: Sinkholes

NASA Astrophysics Data System (ADS)

Onursal Denli, G.; Denli, H. H.

2016-12-01

During the past few years a strange phenomenon has been increasingly observed all over the world. Residents of various places around the world have been taken aback to find sinkholes suddenly come up in their locality - sometimes involving fatalities. A sinkhole is a depression or hole in the ground caused by some form of collapse of the surface layer. The ground caves in all of a sudden, creating large holes in the ground and sometimes devouring whole buildings. Geologists have offered various theories for the natural causes of sinkholes such as the type of soil / rock giving way to rainwater and underground water. Other natural causes submitted by experts include heavy rainfall, global warming, underground gas explosions, etc. They can also occur from the over-pumping and extraction of groundwater and subsurface fluids. In Turkey, especially mid and south-east Anatolian regions have very arid soils. There is not sufficient rain and irrigation in these regions. Despite of using 75% of the fresh water for agriculture, old methods of irrigation causes wastefulness of water. Planless and randomly used water causes difficulties in agriculture. These regions are known as granary in the country. Because of drought, farmers use underground water with draw well unconsciously. At the result of underground water movement and withdrawal of water to surface, depression and very huge holes are occurred in the ground with tremendous noise. During the last two years dozens of sinkholes occurred in these regions in Turkey. Most of them are in the rural area, the others are also in center of the cities. Various sizes of holes scare the people living in these regions. In this study, sinkholes, which are occurred in different dimensions in central Anatolia region in the last years, are observed and the causes of these formations are examined. According to the reasons, suggestions to avoid these formations will be given respectively.

Studies on formation of unconfined detonable vapor cloud using explosive means.

PubMed

Apparao, A; Rao, C R; Tewari, S P

2013-06-15

Certain organic liquid fuels like hydrocarbons, hydrocarbon oxides, when dispersed in air in the form of small droplets, mix with surrounding atmosphere forming vapor cloud (aerosol) and acquire explosive properties. This paper describes the studies on establishment of conditions for dispersion of fuels in air using explosive means resulting in formation of detonable aerosols of propylene oxide and ethylene oxide. Burster charges based on different explosives were evaluated for the capability to disperse the fuels without causing ignition. Parameters like design of canister, burster tube, burster charge type, etc. have been studied based on dispersion experiments. The detonability of the aerosol formed by the optimized burster charge system was also tested. Copyright © 2013 Elsevier B.V. All rights reserved.

Gum and deposit formation from jet turbine and diesel fuels at 100/sup 0/C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayo, F.R.; Lan, B.Y.

1987-02-01

Rates of oxidation and gum formation for six hydrocarbons, three jet turbine fuels and three diesel fuels have been measured at 100/sup 0/C in the presence of t-Bu/sub 2/O/sub 2/ as initiator. Four of the six fuels oxidize faster at 100/sup 0/C than in previous work at 130/sup 0/C without initiator. For any single substrate, the amount of gum produced for the oxygen absorbed is similar at 100 and 130/sup 0/C, even with large changes in rates and t-Bu/sub 2/O/sub 2/ concentrations. In general, the pure hydrocarbons have long kinetic chains and give good yields of hydroperoxides.

Photochemical formation rates of organic aerosols through time-resolved in situ laboratory measurements

NASA Astrophysics Data System (ADS)

Ádámkovics, Máté; Boering, Kristie A.

2003-08-01

The fundamental kinetics of photochemical particle formation and the mechanism(s) for polymerization of hydrocarbons to form condensable species under anoxic conditions have yet to be determined experimentally. Thus these processes remain highly parameterized in models of planetary atmospheres. We have developed instrumentation for simultaneously measuring the net production rates of complex gas-phase hydrocarbons and of organic aerosols formed from irradiating mixtures of simple precursor gases through online quadrupole mass spectrometry measurements of stable gas-phase species and in situ optical scattering detection of the particulates at 633 nm. The new technique and results for the generation of hydrocarbon aerosol from the irradiation of pure, gas-phase CH4 at a pressure of 70 Torr with 8.8 +/- 0.8 × 1015 photons s-1 of vacuum ultraviolet light (120-300nm) are reported. The net production rates for the following gaseous species are measured: H2 = 9.9 +/- 2.2 . 1011, C2H2 = 2.8 +/- 0.5 . 1010, C2H4 = 5.5 +/- 9.4 . 109, C2H6 = 8.6 +/- 2.5 . 1010, C3H4 = 2.5 +/- 1.2 . 109, C4H2 = 6.6 +/- 5.0 . 108, C4H10 = 1.3 +/- 0.5 . 1010 cm-3 s-1. The production of hydrocarbon particulates is detected by optical scattering, and the condensed phase C-C bond formation rate is inferred to be 7.5 +/- 3.1 . 1011 cm-3 s-1. Applications of this technique to the atmospheres of Titan and terrestrial-like planets, such as the early Earth before the rise of molecular oxygen, are discussed.

Method of condensing vaporized water in situ to treat tar sands formations

DOEpatents

Hsu, Chia-Fu

2010-03-16

Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. Heat may be allowed to transfer from the heaters to at least a first portion of the formation. Conditions may be controlled in the formation so that water vaporized by the heaters in the first portion is selectively condensed in a second portion of the formation. At least some of the fluids may be produced from the formation.

Origin of polycyclic aromatic hydrocarbons and other organic pollutants in the air particles of subway stations in Barcelona.

PubMed

van Drooge, Barend L; Prats, Raimon M; Reche, Cristina; Minguillón, MariCruz; Querol, Xavier; Grimalt, Joan O; Moreno, Teresa

2018-06-09

Underground subways transport large numbers of citizens in big cities, which must breathe air with limited ventilation. These atmospheric conditions may enhance the concentration of air pollutants from both outdoor and indoor air. The influence of ventilation conditions and maintenance activities on the concentrations of air pollutants have been studied. Particulate matter with aerodynamic diameter smaller than 2.5 μm (PM 2.5 ) in indoor air was sampled in ten platforms of nine subway stations of the metropolitan area of Barcelona in 2015 and 2016. These particles were analyzed for polycyclic aromatic hydrocarbons (PAH) and organic tracer compounds. The concentrations of PAH were in the range of the street air levels with higher PAH values in the colder period. No influence of nighttime maintenance activities was observed on the platform air quality during daytime. Source apportionment analysis using the concentrations of hopanes, nicotine and levoglucosan as molecular tracer compounds showed that 75% of the detected PAH at the platforms have an outdoor PM origin. The modern subway stations, with advanced ventilation and platform screen doors that separate the subway system from the platform, showed lowest PAH and PM concentrations. Copyright © 2018. Published by Elsevier B.V.

Hydrocarbon Migration from the Micro to Macro Scale in the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Johansen, C.; Marty, E.; Silva, M.; Natter, M.; Shedd, W. W.; Hill, J. C.; Viso, R. F.; Lobodin, V.; Krajewski, L.; Abrams, M.; MacDonald, I. R.

2016-02-01

In the Northern Gulf of Mexico (GoM) at GC600, ECOGIG has been investigating the processes involved in hydrocarbon migration from deep reservoirs to sea surface. We studied two individual vents, Birthday Candles (BC) and Mega-Plume (MP), which are separated by 1km on a salt supported ridge trending from NW-SE. Seismic data depicts two faults, also separated by 1km, feeding into the surface gas hydrate region. BC and MP comprise the range between oily, mixed, and gaseous-type vents. In both cases bubbles are observed escaping from gas hydrate out crops at the sea floor and supporting chemosynthetic communities. Fluid flow is indicated by features on the sea floor such as hydrate mounds, authigenic carbonates, brine pools, mud volcanoes, and biology. We propose a model to describe the upward flow of hydrocarbons from three vertical scales, each dominated by different factors: 1) macro (capillary failure in overlying cap rocks causing reservoir leakage), 2) meso (buoyancy driven fault migration), and 3) micro (hydrate formation and chemosynthetic activity). At the macro scale we use high reflectivity in seismic data and sediment pore throat radii to determine the formation of fractures in leaky reservoirs. Once oil and gas leave the reservoir through fractures in the cap rock they migrate in separate phases. At the meso scale we use seismic data to locate faults and salt diapirs that form conduits for buoyant hydrocarbons follow. This connects the path to the micro scale where we used video data to observe bubble release from individual vents for extended periods of time (3h-26d), and developed an image processing program to quantify bubble release rates. At mixed vents gaseous bubbles are observed escaping hydrate outcrops with a coating of oil varying in thickness. Bubble oil and gas ratios are estimated using average bubble size and release rates. The relative vent age can be described by carbonate hard ground cover, biological activity, and hydrate mound formation as these features progress with persistent hydrocarbon influx. Bottom features along with seismic data, bubble release rates and bubble composition (oily vs gaseous), are implemented into our model to describe the relative vent age and dynamic mechanisms of hydrocarbon migration at three vertical spatial scales of oily and gaseous natural seeps in the GoM.

Understanding Shale Gas: Recent Progress and Remaining Challenges

DOE PAGES

Striolo, Alberto; Cole, David R.

2017-08-27

Because of a number of technological advancements, unconventional hydrocarbons, and in particular shale gas, have transformed the US economy. Much is being learned, as demonstrated by the reduced cost of extracting shale gas in the US over the past five years. However, a number of challenges still need to be addressed. Many of these challenges represent grand scientific and technological tasks, overcoming which will have a number of positive impacts, ranging from the reduction of the environmental footprint of shale gas production to improvements and leaps forward in diverse sectors, including chemical manufacturing and catalytic transformations. This review addresses recentmore » advancements in computational and experimental approaches, which led to improved understanding of, in particular, structure and transport of fluids, including hydrocarbons, electrolytes, water, and CO 2 in heterogeneous subsurface rocks such as those typically found in shale formations. Finally, the narrative is concluded with a suggestion of a few research directions that, by synergistically combining computational and experimental advances, could allow us to overcome some of the hurdles that currently hinder the production of hydrocarbons from shale formations.« less

Effect of persistent trace compounds in landfill gas on engine performance during energy recovery: a case study.

PubMed

Sevimoğlu, Orhan; Tansel, Berrin

2013-01-01

Performances of gas engines operated with landfill gas (LFG) are affected by the impurities in the LFG, reducing the economic viability of energy recovery. The purpose of this study was to characterize the trace compounds in the LFG at the Odayeri Landfill, Istanbul, Turkey which is used for energy recovery. Composite gas samples were collected and analyzed for trace compounds (hydrocarbons, siloxanes, and volatile halogenated hydrocarbons) over a 3-year period. Trace compounds entering the gas engines, their impact on the engine performance were evaluated. The operational problems included deposit formation in the combustion chamber, turbocharger, and intercooler of engine before the scheduled maintenance times. High levels of hydrogen sulfide, as well as chlorinated and fluorinated compounds cause corrosion of the engine parts and decrease life of the engine oils. Persistence of siloxanes results in deposit formation, increasing engine maintenance costs. Pretreatment of LFG is necessary to protect the engines at the waste-to-energy facilities with persistence levels of siloxanes and volatile halogenated hydrocarbons. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sembar Goru/Ghazij Composite Total Petroleum System, Indus and Sulaiman-Kirthar Geologic Provinces, Pakistan and India

USGS Publications Warehouse

Wandrey, C.J.; Law, B.E.; Shah, Haider Ali

2004-01-01

Geochemical analyses of rock samples and produced oil and gas in the Indus Basin have shown that the bulk of the hydrocarbons produced in the Indus Basin are derived from the Lower Cretaceous Sembar Formation and equivalent rocks. The source rocks of the Sembar are composed of shales that were deposited in shallow marine environments, are of mixed type-II and type-III kerogen, with total organic carbon (TOC) content ranging from less than 0.5 percent to more than 3.5 percent; the average TOC of the Sembar is about 1.4 percent. Vitrinite reflectance (Ro) values range from immature (1.35 percent Ro). Thermal generation of hydrocarbons in the Sembar Formation began 65 to 40 million years ago, (Mya) during Paleocene to Oligocene time. Hydrocarbon expulsion, migration, and entrapment are interpreted to have occurred mainly 50 to 15 Mya, during Eocene to Miocene time, prior to and contemporaneously with the development of structural traps in Upper Cretaceous and Tertiary reservoirs. The principal reservoirs in the Sembar-Goru/Ghazij Composite Total Petroleum System are Upper Cretaceous through Eocene sandstones and limestones.

Formation of combustible hydrocarbons and H2 during photocatalytic decomposition of various organic compounds under aerated and deaerated conditions.

PubMed

Mozia, Sylwia; Kułagowska, Aleksandra; Morawski, Antoni W

2014-11-26

A possibility of photocatalytic production of useful aliphatic hydrocarbons and H2 from various organic compounds, including acetic acid, methanol, ethanol and glucose, over Fe-modified TiO2 is discussed. In particular, the influence of the reaction atmosphere (N2, air) was investigated. Different gases were identified in the headspace volume of the reactor depending on the substrate. In general, the evolution of the gases was more effective in air compared to a N2 atmosphere. In the presence of air, the gaseous phase contained CO2, CH4 and H2, regardless of the substrate used. Moreover, formation of C2H6 and C3H8 in the case of acetic acid and C2H6 in the case of ethanol was observed. In case of acetic acid and methanol an increase in H2 evolution under aerated conditions was observed. It was concluded that the photocatalytic decomposition of organic compounds with simultaneous generation of combustible hydrocarbons and hydrogen could be a promising method of "green energy" production.

Remote carboxylation of halogenated aliphatic hydrocarbons with carbon dioxide

NASA Astrophysics Data System (ADS)

Juliá-Hernández, Francisco; Moragas, Toni; Cornella, Josep; Martin, Ruben

2017-05-01

Catalytic carbon-carbon bond formation has enabled the streamlining of synthetic routes when assembling complex molecules. It is particularly important when incorporating saturated hydrocarbons, which are common motifs in petrochemicals and biologically relevant molecules. However, cross-coupling methods that involve alkyl electrophiles result in catalytic bond formation only at specific and previously functionalized sites. Here we describe a catalytic method that is capable of promoting carboxylation reactions at remote and unfunctionalized aliphatic sites with carbon dioxide at atmospheric pressure. The reaction occurs via selective migration of the catalyst along the hydrocarbon side-chain with excellent regio- and chemoselectivity, representing a remarkable reactivity relay when compared with classical cross-coupling reactions. Our results demonstrate that site-selectivity can be switched and controlled, enabling the functionalization of less-reactive positions in the presence of a priori more reactive ones. Furthermore, we show that raw materials obtained in bulk from petroleum processing, such as alkanes and unrefined mixtures of olefins, can be used as substrates. This offers an opportunity to integrate a catalytic platform en route to valuable fatty acids by transforming petroleum-derived feedstocks directly.

The thermal degradation of 5 alpha (H)-cholestane during closed-system pyrolysis

NASA Astrophysics Data System (ADS)

Abbott, Geoffrey D.; Bennett, Barry; Stuart Fetch, G.

1995-06-01

Involatile hydrocarbons were identified following the heating of 5α(H)-cholestane in water with reaction vessel walls composed of 316 grade stainless steel and borosilicate glass. These analyses were compared with the hydrocarbon product compositions from closed-system pyrolysis experiments with no added water. Unsaturated hydrocarbons dominate their saturated counterparts following hydrous pyrolysis in both stainless steel-316 and borosilicate glass. In the absence of added water the converse is true in that saturated components dominate the hydrocarbon mixture. Backbone rearrangement in the steroid nucleus leading to spirosterene formation was only observed under aqueous conditions in both borosilicate glass and stainless steel-316 vessels. These comparisons demonstrate that water, as opposed to reaction vessel surface catalytic effects, plays a central role in mediating hydrocarbon degradation during closed-system hydrous pyrolysis. 5α(H)-cholestane degradation under aqueous conditions is a complex composite of dissociative and rearrangement processes. These include (I) carbon-carbon bond cleavage in the sidechains as well as the ring system, (2) dehydrogenation, and (3) backbone rearrangement. These laboratory experiments provide a product description of the involatile hydrocarbons which will be the basis for a mechanistic study of 5α(H)-cholestane degradation in hot water.

The role of the underground for massive storage of energy: a preliminary glance of the French case

NASA Astrophysics Data System (ADS)

Audigane, Pascal; Gentier, Sylvie; Bader, Anne-Gaelle; Beccaletto, Laurent; Bellenfant, Gael

2014-05-01

The question of storing energy in France has become of primary importance since the launch of a road map from the government which places in pole position this topic among seven major milestones to be challenged in the context of the development of innovative technology in the country. The European objective to reach 20% of renewables in the energy market, from which a large part would come from wind and solar power generation, raises several issues regarding the capacity of the grid to manage the various intermittent energy sources in line with the variability of the public demand and offer. These uncertainties are highly influenced by unpredictable weather and economic fluctuations. To facilitate the large-scale integration of variable renewable electricity sources in grids, massive energy storage is needed. In that case, electric energy storage techniques involving the use of underground are often under consideration as they offer a large storage capacity volume with a adapted potential of confining and the space required for the implantation. Among the panel of massive storage technologies, one can find (i) the Underground Pumped Hydro-Storage (UPHS) which are an adaptation of classical Pumped Hydro Storage system often connected with dam constructions, (ii) the compressed air storage (CAES) and (iii) the hydrogen storage from conversion of electricity into H2 and O2 by electrolysis. UPHS concept is based on using the potential energy between two water reservoirs positioned at different heights. Favorable natural locations like mountainous areas or cliffs are spatially limited given the geography of the territory. This concept could be extended with the integration of one of these reservoirs in an underground cavities (specifically mined or reuse of preexisting mines) to increase opportunities on the national territory. Massive storage based on compression and relaxation of air (CAES) requires high volume and confining pressure around the storage that exists naturally in the underground and which increases with depth. However, the move to an interesting efficiency requires that the heat generated during compression can be stored and used during expansion. This storage can be also underground. H2 underground storage is part of the "Power to gas" concept which allows for converting electricity into a gas available for either electrical or gas grid. Each of these techniques requires the selection of appropriate geological formations which contains specific characteristics in agreement with several criteria under consideration when choosing electric energy storage methods for application (lifetime, life cycle, discharge rate, environmental impact, public acceptance …). We propose in this paper a preliminary review of the potential massive electric energy storage capacities in France of using specific geological formations (salt, basement) and the various physical phenomena linked to the couple geology/technology. Several approaches and methodologies developed formerly with other applications (geothermal, CO2 storage, heat storage …) will be used to investigate mechanical integrity and environmental impacts associated to these innovative technologies.

Calculation of hydrocarbon-in-place in gas and gas-condensate reservoirs - Carbon dioxide sequestration

USGS Publications Warehouse

Verma, Mahendra K.

2012-01-01

The Energy Independence and Security Act of 2007 (Public Law 110-140) authorized the U.S. Geological Survey (USGS) to conduct a national assessment of geologic storage resources for carbon dioxide (CO2), requiring estimation of hydrocarbon-in-place volumes and formation volume factors for all the oil, gas, and gas-condensate reservoirs within the U.S. sedimentary basins. The procedures to calculate in-place volumes for oil and gas reservoirs have already been presented by Verma and Bird (2005) to help with the USGS assessment of the undiscovered resources in the National Petroleum Reserve, Alaska, but there is no straightforward procedure available for calculating in-place volumes for gas-condensate reservoirs for the carbon sequestration project. The objective of the present study is to propose a simple procedure for calculating the hydrocarbon-in-place volume of a condensate reservoir to help estimate the hydrocarbon pore volume for potential CO2 sequestration.

The in vivo hydrocarbon formation by vanadium nitrogenase follows a secondary metabolic pathway

DOE PAGES

Rebelein, Johannes G.; Lee, Chi Chung; Hu, Yilin; ...

2016-12-15

The vanadium (V)-nitrogenase of Azotobacter vinelandii catalyses the in vitro conversion of carbon monoxide (CO) to hydrocarbons. Here we show that an A. vinelandii strain expressing the V-nitrogenase is capable of in vivo reduction of CO to ethylene (C 2H 4), ethane (C 2H 6) and propane (C 3H 8). Moreover, we demonstrate that CO is not used as a carbon source for cell growth, being instead reduced to hydrocarbons in a secondary metabolic pathway. These findings suggest a possible role of the ancient nitrogenase as an evolutionary link between the carbon and nitrogen cycles on Earth and establish amore » solid foundation for biotechnological adaptation of a whole-cell approach to recycling carbon wastes into hydrocarbon products. Furthermore, this study has several repercussions for evolution-, environment- and energy-related areas.« less

Elemental sulfur in Eddy County, New Mexico

USGS Publications Warehouse

Hinds, Jim S.; Cunningham, Richard R.

1970-01-01

Sulfur has been reported in Eddy County, N. Mex., in rocks ranging from Silurian to Holocene in age at depths of 0-15,020 feet. Targets of present exploration are Permian formations in the Delaware Basin and northwest shelf areas at depths of less than 4,000 feet. Most of the reported sulfur occurrences in the shelf area are in the 'Abo' (as used by some subsurface geologists), Yeso, and San Andres Formations and the Artesia Group. Sulfur deposition in the dense dolomites of the 'Abo,' Yeso, and San Andres Formations is attributed to the reduction of ionic sulfate by hydrogen sulfide in formation waters in zones of preexisting porosity and permeability. A similar origin accounts for most of the sulfur deposits in the formations of the Artesia Group, but some of the sulfur in these formations may have originated in place through the alteration of anhydrite to carbonate and sulfur by the metabolic processes of bacteria in the presence of hydrocarbons. Exploration in the Delaware Basin area is directed primarily toward the Castile Formation. Sulfur deposits in the Castile Formation are found in irregular masses of cavernous brecciated secondary carbonate rock enveloped by impermeable anhydrite. The carbonate masses, or 'castiles,' probably originated as collapse features resulting from subsurface solution and upward stopping. Formation of carbonate rock and sulfur in the castiles is attributed to the reduction of brecciated anhydrite by bacteria and hydrocarbons in the same process ascribed to the formation of carbonate and sulfur in the caprocks of salt domes.

Marine and nonmarine gas-bearing rocks in Upper Cretaceous Blackhawk and Neslen Formations, eastern Uinta Basin, Utah: sedimentology, diagenesis, and source rock potential

USGS Publications Warehouse

Pitman, Janet K.; Franczyk, K.J.; Anders, D.E.

1987-01-01

Thermogenic gas was generated from interbedded humic-rich source rocks. The geometry and distribution of hydrocarbon source and reservoir rocks are controlled by depositional environment. The rate of hydrocarbon generation decreased from the late Miocene to the present, owing to widespread cooling that occurred in response to regional uplift and erosion associated with the development of the Colorado Plateau. -from Authors

Application of magnetic techniques to lateral hydrocarbon migration - Lower Tertiary reservoir systems, UK North Sea

NASA Astrophysics Data System (ADS)

Badejo, S. A.; Muxworthy, A. R.; Fraser, A.

2017-12-01

Pyrolysis experiments show that magnetic minerals can be produced inorganically during oil formation in the `oil-kitchen'. Here we try to identify a magnetic proxy that can be used to trace hydrocarbon migration pathways by determining the morphology, abundance, mineralogy and size of the magnetic minerals present in reservoirs. We address this by examining the Tay formation in the Western Central Graben in the North Sea. The Tertiary sandstones are undeformed and laterally continuous in the form of an east-west trending channel, facilitating long distance updip migration of oil and gas to the west. We have collected 179 samples from 20 oil-stained wells and 15 samples from three dry wells from the British Geological Survey Core Repository. Samples were selected based on geological observations (water-wet sandstone, oil-stained sandstone, siltstones and shale). The magnetic properties of the samples were determined using room-temperature measurements on a Vibrating Sample Magnetometer (VSM), low-temperature (0-300K) measurements on a Magnetic Property Measurement System (MPMS) and high-temperature (300-973K) measurements on a Kappabridge susceptibility meter. We identified magnetite, pyrrhotite, pyrite and siderite in the samples. An increasing presence of ferrimagnetic iron sulphides is noticed along the known hydrocarbon migration pathway. Our initial results suggest mineralogy coupled with changes in grain size are possible proxies for hydrocarbon migration.

Sulfur driven nucleation mode formation in diesel exhaust under transient driving conditions.

PubMed

Karjalainen, Panu; Rönkkö, Topi; Pirjola, Liisa; Heikkilä, Juha; Happonen, Matti; Arnold, Frank; Rothe, Dieter; Bielaczyc, Piotr; Keskinen, Jorma

2014-02-18

Sulfur driven diesel exhaust nucleation particle formation processes were studied in an aerosol laboratory, on engine dynamometers, and on the road. All test engines were equipped with a combination of a diesel oxidation catalyst (DOC) and a partial diesel particulate filter (pDPF). At steady operating conditions, the formation of semivolatile nucleation particles directly depended on SO2 conversion in the catalyst. The nucleation particle emission was most significant after a rapid increase in engine load and exhaust gas temperature. Results indicate that the nucleation particle formation at transient driving conditions does not require compounds such as hydrocarbons or sulfated hydrocarbons, however, it cannot be explained only by the nucleation of sulfuric acid. A real-world exhaust study with a heavy duty diesel truck showed that the nucleation particle formation occurs even with ultralow sulfur diesel fuel, even at downhill driving conditions, and that nucleation particles can contribute 60% of total particle number emissions. In general, due to sulfur storage and release within the exhaust aftertreatment systems and transients in driving, emissions of nucleation particles can even be the dominant part of modern diesel vehicle exhaust particulate number emissions.

SECONDARY ORGANIC AEROSOL FORMATION FROM THE OXIDATION OF AROMATIC HYDROCARBONS IN THE PRESENCE OF DRY SUBMICRON AMMONIUM SULFATE AEROSOL

EPA Science Inventory

A laboratory study was conducted to examine formation of secondary organic aerosols. A smog chamber system was developed for studying gas-aerosol interactions in a dynamic flow reactor. These experiments were conducted to investigate the fate of gas and aerosol phase compounds ...

Catalytic co-pyrolysis of switchgrass and polyethylene over HZSM-5: catalyst deactivation and coke formation

USDA-ARS?s Scientific Manuscript database

When conducted in the presence of a zeolite catalyst such as HZSM-5, fast pyrolysis of biomass can promote the rejection of oxygen and the formation of aromatic hydrocarbons in the organic liquid products. Unfortunately, this pathway removes hydrogen from the already hydrogen deficient biomass start...

Particle Generation and Evolution in Silane/Acetylene Flames in Microgravity

NASA Technical Reports Server (NTRS)

Keil, D. G.

2001-01-01

The objective of this new experimental program is to advance the understanding of the formation of particles from gas phase combustion processes. The work will utilize the unique SiH4/C2H2 combustion system which generates particulate products ranging from high purity, white SiC to carbonaceous soot depending on equivalence ratio. A key goal of this work is to identify gas phase or particle formation processes that provide the enthalpy release necessary to drive the combustion wave, and to locate the parts of the particle formation process that determine SiC stoichiometry and crystallinity. In a real sense, these SiH4/C2H2 flames act like "highly sooty" hydrocarbon flames, but with simpler chemistry. This simplification is expected to allow them to be used as surrogates to advance understanding of soot formation in such rich hydrocarbon flames. It is also expected that this improved understanding of SiC particle generation and evolution in these self-sustaining flames will advance the commercial potential of the flame process for the generation of high purity SiC powders.

Particle Generation And Evolution In Silane (SiH4)/Acetylene (C2H2) Flames In Microgravity

NASA Technical Reports Server (NTRS)

Keil, D. G.

2003-01-01

The objective of this experimental program is to advance the understanding of the coupling of particle formation with gas phase combustion processes. The work utilizes the unique SiH4/C2H2 combustion system which generates particulate products ranging from high purity, white SiC to carbonaceous soot depending on equivalence ratio (Ref. 1). A goal of this work is to identify gas phase or particle formation processes that provide the enthalpy release needed to drive the combustion wave, and to locate the steps of the particle formation process that determine SiC stoichiometry and crystallinity. In a real sense, these SiH4/C2H2 flames act like highly sooty hydrocarbon flames, but with simpler chemistry. This simplification is expected to allow them to be used as surrogates to advance understanding of soot formation in such rich hydrocarbon flames. It is also expected that this improved understanding of SiC particle generation and evolution in these self-sustaining flames will advance the commercial potential of the flame process for the generation of high purity SiC powders.

Chloromethane to olefins over H-SAPO-34: Probing the hydrocarbon pool mechanism

DOE PAGES

Fickel, Dustin W.; Sabnis, Kaiwalya D.; Li, Luanyi; ...

2016-09-09

In this paper, by means of in situ FTIR and ex situ 13C NMR studies, the initial periods of the chloromethane-to-olefins (CTO) reaction over SAPO-34 were probed in order to investigate the activation period of the reaction and to elucidate the formation of the catalyst active site. A methylated benzene species has been observed to form during the initial activation period of the reaction, and a direct positive correlation was constructed between the formation of this species and the catalytic activity. The data thus indicate that these methylated benzene species contribute to the formation of active sites within SAPO-34 formore » the CTO reaction. This is the first known report identifying a direct semi-quantitative correlation between the catalyst activity and growth of a methylated benzene active species, during the activation period of the chloromethane to olefins reaction. Finally, the findings here in correspond well to those reported for the methanol to olefins reaction, suggesting that a similar ‘hydrocarbon pool’ mechanism may be responsible for the formation of light olefins in CTO chemistry as well.« less

Geochemical signatures of thermochemical sulfate reduction in controlled hydrous pyrolysis experiments

USGS Publications Warehouse

Zhang, T.; Ellis, G.S.; Walters, C.C.; Kelemen, S.R.; Wang, K.-s.; Tang, Y.

2008-01-01

A series of gold tube hydrous pyrolysis experiments was conducted in order to investigate the effect of thermochemical sulfate reduction (TSR) on gas generation, residual saturated hydrocarbon compositional alteration, and solid pyrobitumen formation. The intensity of TSR significantly depends on the H2O/MgSO4 mole ratio, the smaller the ratio, the stronger the oxidizing conditions. Under highly oxidizing conditions (MgSO4/hydrocarbon wt/wt 20/1 and hydrocarbon/H2O wt/wt 1/1), large amounts of H2S and CO2 are generated indicating that hydrocarbon oxidation coupled with sulfate reduction is the dominant reaction. Starting with a mixture of C21-C35 n-alkanes, these hydrocarbons are consumed totally at temperatures below the onset of hydrocarbon thermal cracking in the absence of TSR (400 ??C). Moreover, once the longer chain length hydrocarbons are oxidized, secondarily formed hydrocarbons, even methane, are oxidized to CO2. Using whole crude oils as the starting reactants, the TSR reaction dramatically lowers the stability of hydrocarbons leading to increases in gas dryness and gas/oil ratio. While their concentrations decrease, the relative distributions of n-alkanes do not change appreciably from the original composition, and consequently, are non-diagnostic for TSR. However, distinct molecular changes related to TSR are observed, Pr/n-C17 and Ph/n-C18 ratios decrease at a faster rate under TSR compared to thermal chemical alteration (TCA) alone. TSR promotes aromatization and the incorporation of sulfur and oxygen into hydrocarbons leading to a decrease in the saturate to aromatic ratio in the residual oil and in the generation of sulfur and oxygen rich pyrobitumen. These experimental findings could provide useful geochemical signatures to identify TSR in settings where TSR has occurred in natural systems. ?? 2008 Elsevier Ltd. All rights reserved.

Cleanup of a jet fuel spill

NASA Astrophysics Data System (ADS)

Fesko, Steve

1996-11-01

Eaton operates a corporate aircraft hanger facility in Battle Creek, Michigan. Tests showed that two underground storage tanks leaked. Investigation confirmed this release discharged several hundred gallons of Jet A kerosene into the soil and groundwater. The oil moved downward approximately 30 feet and spread laterally onto the water table. Test results showed kerosene in the adsorbed, free and dissolved states. Eaton researched and investigated three clean-up options. They included pump and treat, dig and haul and bioremediation. Jet fuel is composed of readily biodegradable hydrocarbon chains. This fact coupled with the depth to groundwater and geologic setting made bioremediation the low cost and most effective alternative. A recovery well was installed at the leading edge of the dissolved contamination. A pump moved water from this well into a nutrient addition system. Nutrients added included nitrogen, phosphorous and potassium. Additionally, air was sparged into the water. The water was discharged into an infiltration gallery installed when the underground storage tanks were removed. Water circulated between the pump and the infiltration basin in a closed loop fashion. This oxygenated, nutrient rich water actively and aggressively treated the soils between the bottom of the gallery and the top of the groundwater and the groundwater. The system began operating in August of 1993 and reduced jet fuel to below detection levels. In August of 1995 The State of Michigan issued a clean closure declaration to the site.

Development and investigation of a pollution control pit for treatment of stormwater from metal roofs and traffic areas.

PubMed

Dierkes, C; Göbel, P; Lohmann, M; Coldewey, W G

2006-01-01

Source control by on-site retention and infiltration of stormwater is a sustainable and proven alternative to classical drainage methods. Unfortunately, sedimentary particles and pollutants from drained surfaces cause clogging and endanger soil and groundwater during long-term operation of infiltration devices. German water authorities recommend the use of infiltration devices, such as swales or swale-trench-systems. Direct infiltration by underground facilities, such as pipes, trenches or sinks, without pretreatment of runoff is generally not permitted. Problems occur with runoff from metal roofs, traffic areas and industrial sites. However, due to site limitations, underground systems are often the only feasible option. To overcome this situation, a pollution control pit was developed with a hydrodynamic separator and a multistage filter made of coated porous concrete. The system treats runoff at source and protects soil, groundwater and receiving waterways. Typically, more than 90% of the pollutants such as sedimentary particles, hydrocarbons and heavy metals can be removed. Filters have been developed to treat even higher polluted stormwater loads from metal roofs and industrial sites. The treatment process is based on sedimentation, filtration, adsorption and chemical precipitation. Sediments are trapped in a special chamber within the pit and can be removed easily. Other pollutants are captured in the concrete filter upstream of the sediment separator chamber. Filters can be easily replaced.

Calibration of an Ultra-Low-Background Proportional Counter for Measuring 37Ar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seifert, Allen; Aalseth, Craig E.; Bonicalzi, Ricco

Abstract. An ultra-low-background proportional counter (ULBPC) design has been developed at Pacific Northwest National Laboratory (PNNL) using clean materials, primarily electrochemically-purified copper. This detector, along with an ultra-low-background counting system (ULBCS), was developed to complement a new shallow underground laboratory (30 meters water-equivalent) constructed at PNNL. The ULBCS design includes passive neutron and gamma shielding, along with an active cosmic-veto system. This system provides a capability for making ultra-sensitive measurements to support applications like age-dating soil hydrocarbons with 14C/3H, age-dating of groundwater with 39Ar, and soil-gas assay for 37Ar to support On-Site Inspection (OSI). On-Site Inspection is a key componentmore » of the verification regime for the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Measurements of radionuclides created by an underground nuclear explosion are valuable signatures of a Treaty violation. For OSI, the 35-day half-life of 37Ar, produced from neutron interactions with calcium in soil, provides both high specific activity and sufficient time for inspection before decay limits sensitivity. This work describes the calibration techniques and analysis methods developed to enable quantitative measurements of 37Ar samples over a broad range of pressures. These efforts, along with parallel work in progress on gas chemistry separation, are expected to provide a significant new capability for 37Ar soil gas background studies.« less

Insights into the Activity and Deactivation of the Methanol-to-Olefins Process over Different Small-Pore Zeolites As Studied with Operando UV-vis Spectroscopy.

PubMed

Goetze, Joris; Meirer, Florian; Yarulina, Irina; Gascon, Jorge; Kapteijn, Freek; Ruiz-Martínez, Javier; Weckhuysen, Bert M

2017-06-02

The nature and evolution of the hydrocarbon pool (HP) species during the Methanol-to-Olefins (MTO) process for three small-pore zeolite catalysts, with a different framework consisting of large cages interconnected by small eight-ring windows (CHA, DDR, and LEV) was studied at reaction temperatures between 350 and 450 °C using a combination of operando UV-vis spectroscopy and online gas chromatography. It was found that small differences in cage size, shape, and pore structure of the zeolite frameworks result in the generation of different hydrocarbon pool species. More specifically, it was found that the large cage of CHA results in the formation of a wide variety of hydrocarbon pool species, mostly alkylated benzenes and naphthalenes. In the DDR cage, 1-methylnaphthalene is preferentially formed, while the small LEV cage generally contains fewer hydrocarbon pool species. The nature and evolution of these hydrocarbon pool species was linked with the stage of the reaction using a multivariate analysis of the operando UV-vis spectra. In the 3-D pore network of CHA, the reaction temperature has only a minor effect on the performance of the MTO catalyst. However, for the 2-D pore networks of DDR and LEV, an increase in the applied reaction temperature resulted in a dramatic increase in catalytic activity. For all zeolites in this study, the role of the hydrocarbon species changes with reaction temperature. This effect is most clear in DDR, in which diamantane and 1-methylnaphthalene are deactivating species at a reaction temperature of 350 °C, whereas at higher temperatures diamantane formation is not observed and 1-methylnaphthalene is an active species. This results in a different amount and nature of coke species in the deactivated catalyst, depending on zeolite framework and reaction temperature.

Insights into the Activity and Deactivation of the Methanol-to-Olefins Process over Different Small-Pore Zeolites As Studied with Operando UV–vis Spectroscopy

PubMed Central

2017-01-01

The nature and evolution of the hydrocarbon pool (HP) species during the Methanol-to-Olefins (MTO) process for three small-pore zeolite catalysts, with a different framework consisting of large cages interconnected by small eight-ring windows (CHA, DDR, and LEV) was studied at reaction temperatures between 350 and 450 °C using a combination of operando UV–vis spectroscopy and online gas chromatography. It was found that small differences in cage size, shape, and pore structure of the zeolite frameworks result in the generation of different hydrocarbon pool species. More specifically, it was found that the large cage of CHA results in the formation of a wide variety of hydrocarbon pool species, mostly alkylated benzenes and naphthalenes. In the DDR cage, 1-methylnaphthalene is preferentially formed, while the small LEV cage generally contains fewer hydrocarbon pool species. The nature and evolution of these hydrocarbon pool species was linked with the stage of the reaction using a multivariate analysis of the operando UV–vis spectra. In the 3-D pore network of CHA, the reaction temperature has only a minor effect on the performance of the MTO catalyst. However, for the 2-D pore networks of DDR and LEV, an increase in the applied reaction temperature resulted in a dramatic increase in catalytic activity. For all zeolites in this study, the role of the hydrocarbon species changes with reaction temperature. This effect is most clear in DDR, in which diamantane and 1-methylnaphthalene are deactivating species at a reaction temperature of 350 °C, whereas at higher temperatures diamantane formation is not observed and 1-methylnaphthalene is an active species. This results in a different amount and nature of coke species in the deactivated catalyst, depending on zeolite framework and reaction temperature. PMID:28603658

The marine bacterium Marinobacter hydrocarbonoclasticus SP17 degrades a wide range of lipids and hydrocarbons through the formation of oleolytic biofilms with distinct gene expression profiles.

PubMed

Mounier, Julie; Camus, Arantxa; Mitteau, Isabelle; Vaysse, Pierre-Joseph; Goulas, Philippe; Grimaud, Régis; Sivadon, Pierre

2014-12-01

Hydrophobic organic compounds (mainly lipids and hydrocarbons) represent a significant part of the organic matter in marine waters, and their degradation has an important impact in the carbon fluxes within oceans. However, because they are nearly insoluble in the water phase, their degradation by microorganisms occurs at the interface with water and thus requires specific adaptations such as biofilm formation. We show that Marinobacter hydrocarbonoclasticus SP17 develops biofilms, referred to as oleolytic biofilms, on a large variety of hydrophobic substrates, including hydrocarbons, fatty alcohols, fatty acids, triglycerides, and wax esters. Microarray analysis revealed that biofilm growth on n-hexadecane or triolein involved distinct genetic responses, together with a core of common genes that might concern general mechanisms of biofilm formation. Biofilm growth on triolein modulated the expression of hundreds of genes in comparison with n-hexadecane. The processes related to primary metabolism and genetic information processing were downregulated. Most of the genes that were overexpressed on triolein had unknown functions. Surprisingly, their genome localization was restricted to a few regions identified as putative genomic islands or mobile elements. These results are discussed with regard to the adaptive responses triggered by M. hydrocarbonoclasticus SP17 to occupy a specific niche in marine ecosystems. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Monohydroxylated polycyclic aromatic hydrocarbons influence spicule formation in the early development of sea urchins (Hemicentrotus pulcherrimus).

PubMed

Suzuki, Nobuo; Ogiso, Shouzo; Yachiguchi, Koji; Kawabe, Kimi; Makino, Fumiya; Toriba, Akira; Kiyomoto, Masato; Sekiguchi, Toshio; Tabuchi, Yoshiaki; Kondo, Takashi; Kitamura, Kei-ichiro; Hong, Chun-Sang; Srivastav, Ajai K; Oshima, Yuji; Hattori, Atsuhiko; Hayakawa, Kazuichi

2015-05-01

We previously demonstrated that monohydroxylated polycyclic aromatic hydrocarbons (OHPAHs), which are metabolites of polycyclic aromatic hydrocarbons (PAHs), act on calcified tissue and suppress osteoblastic and osteoclastic activity in the scales of teleost fish. The compounds may possibly influence other calcified tissues. Thus, the present study noted the calcified spicules in sea urchins and examined the effect of both PAHs and OHPAHs on spicule formation during the embryogenesis of sea urchins. After fertilization, benz[a]anthracene (BaA) and 4-hydroxybenz[a]anthracene (4-OHBaA) were added to seawater at concentrations of 10(-8) and 10(-7) M and kept at 18 °C. The influence of the compound was given at the time of the pluteus larva. At this stage, the length of the spicule was significantly suppressed by 4-OHBaA (10(-8) and 10(-7) M). BaA (10(-7) M) decreased the length of the spicule significantly, while the length did not change with BaA (10(-8) M). The expression of mRNAs (spicule matrix protein and transcription factors) in the 4-OHBaA (10(-7) M)-treated embryos was more strongly inhibited than were those in the BaA (10(-7) M)-treated embryos. This is the first study to demonstrate that OHPAHs suppress spicule formation in sea urchins. Copyright © 2015 Elsevier Inc. All rights reserved.

Petrology and diagenetic history of the upper shale member of the Late Devonian-Early Mississippian Bakken Formation, Williston Basin, North Dakota

USGS Publications Warehouse

Neil S. Fishman,; Sven O. Egenhoff,; Boehlke, Adam; Lowers, Heather A.

2015-01-01

The organic-rich upper shale member of the upper Devonian–lower Mississippian Bakken Formation (Williston Basin, North Dakota, USA) has undergone significant diagenetic alteration, irrespective of catagenesis related to hydrocarbon generation. Alteration includes precipitation of numerous cements, replacement of both detrital and authigenic minerals, multiple episodes of fracturing, and compaction. Quartz authigenesis occurred throughout much of the member, and is represented by multiple generations of microcrystalline quartz. Chalcedonic quartz fills radiolarian microfossils and is present in the matrix. Sulfide minerals include pyrite and sphalerite. Carbonate diagenesis is volumetrically minor and includes thin dolomite overgrowths and calcite cement. At least two generations of fractures are observed. Based on the authigenic minerals and their relative timing of formation, the evolution of pore waters can be postulated. Dolomite and calcite resulted from early postdepositional aerobic oxidation of some of the abundant organic material in the formation. Following aerobic oxidation, conditions became anoxic and sulfide minerals precipitated. Transformation of the originally opaline tests of radiolaria resulted in precipitation of quartz, and quartz authigenesis is most common in more distal parts of the depositional basin where radiolaria were abundant. Because quartz authigenesis is related to the distribution of radiolaria, there is a link between diagenesis and depositional environment. Furthermore, much of the diagenesis in the upper shale member preceded hydrocarbon generation, so early postdepositional processes were responsible for occlusion of significant original porosity in the member. Thus, diagenetic mineral precipitation was at least partly responsible for the limited ability of these mudstones to provide porosity for storage of hydrocarbons.

Ambient aromatic hydrocarbon measurements at Welgegund, South Africa

NASA Astrophysics Data System (ADS)

Jaars, K.; Beukes, J. P.; van Zyl, P. G.; Venter, A. D.; Josipovic, M.; Pienaar, J. J.; Vakkari, V.; Aaltonen, H.; Laakso, H.; Kulmala, M.; Tiitta, P.; Guenther, A.; Hellén, H.; Laakso, L.; Hakola, H.

2014-07-01

Aromatic hydrocarbons are associated with direct adverse human health effects and can have negative impacts on ecosystems due to their toxicity, as well as indirect negative effects through the formation of tropospheric ozone and secondary organic aerosol, which affect human health, crop production and regional climate. Measurements of aromatic hydrocarbons were conducted at the Welgegund measurement station (South Africa), which is considered to be a regionally representative background site. However, the site is occasionally impacted by plumes from major anthropogenic source regions in the interior of South Africa, which include the western Bushveld Igneous Complex (e.g. platinum, base metal and ferrochrome smelters), the eastern Bushveld Igneous Complex (platinum and ferrochrome smelters), the Johannesburg-Pretoria metropolitan conurbation (> 10 million people), the Vaal Triangle (e.g. petrochemical and pyrometallurgical industries), the Mpumalanga Highveld (e.g. coal-fired power plants and petrochemical industry) and also a region of anticyclonic recirculation of air mass over the interior of South Africa. The aromatic hydrocarbon measurements were conducted with an automated sampler on Tenax-TA and Carbopack-B adsorbent tubes with heated inlet for 1 year. Samples were collected twice a week for 2 h during daytime and 2 h during night-time. A thermal desorption unit, connected to a gas chromatograph and a mass selective detector was used for sample preparation and analysis. Results indicated that the monthly median (mean) total aromatic hydrocarbon concentrations ranged between 0.01 (0.011) and 3.1 (3.2) ppb. Benzene levels did not exceed the local air quality standard limit, i.e. annual mean of 1.6 ppb. Toluene was the most abundant compound, with an annual median (mean) concentration of 0.63 (0.89) ppb. No statistically significant differences in the concentrations measured during daytime and night-time were found, and no distinct seasonal patterns were observed. Air mass back trajectory analysis indicated that the lack of seasonal cycles could be attributed to patterns determining the origin of the air masses sampled. Aromatic hydrocarbon concentrations were in general significantly higher in air masses that passed over anthropogenically impacted regions. Inter-compound correlations and ratios gave some indications of the possible sources of the different aromatic hydrocarbons in the source regions defined in the paper. The highest contribution of aromatic hydrocarbon concentrations to ozone formation potential was also observed in plumes passing over anthropogenically impacted regions.

Monitoring the excavation damaged zone by three-dimensional reconstruction of electrical resistivity

NASA Astrophysics Data System (ADS)

Lesparre, Nolwenn; Gibert, Dominique; Nicollin, Florence; Nussbaum, Christophe; Adler, Andy

2013-11-01

A damaged zone is formed during the excavation of underground galleries, altering the rock properties. From a perspective of nuclear waste storage in deep geological sites, there is a clear interest to monitor the rock properties in such zones. We constructed electrical resistivity tomograms as a function of time to monitor the damaged area in gallery 04 of the Mont Terri underground rock laboratory (Switzerland). Measurements were performed using electrode rings surrounding the gallery. The experience showed a heterogeneous distribution of damages around the gallery and their fast formation after the excavation. Two main areas were concerned by damage formation, located in regions where the bedding was tangential to the excavated gallery. Such regions represented an extension of about 2 m along the gallery walls and reached a depth of 1.5 m. Main damages were created during the next months following the excavation process. Slight variations were still observed 3 yr after the excavation that may be related to the gallery environmental condition fluctuation. The method applied here demonstrates the interest to monitor the whole region surrounding excavated galleries dedicated to host nuclear wastes.

Creating potentiometric surfaces from combined water well and oil well data in the midcontinent of the United States

USGS Publications Warehouse

Gianoutsos, Nicholas J.; Nelson, Philip H.

2013-01-01

For years, hydrologists have defined potentiometric surfaces using measured hydraulic-head values in water wells from aquifers. Down-dip, the oil and gas industry is also interested in the formation pressures of many of the same geologic formations for the purpose of hydrocarbon recovery. In oil and gas exploration, drillstem tests (DSTs) provide the formation pressure for a given depth interval in a well. These DST measurements can be used to calculate hydraulic-head values in deep hydrocarbon-bearing formations in areas where water wells do not exist. Unlike hydraulic-head measurements in water wells, which have a low number of problematic data points (outliers), only a small subset of the DST data measure true formation pressures. Using 3D imaging capabilities to view and clean the data, we have developed a process to estimate potentiometric surfaces from erratic DST data sets of hydrocarbon-bearing formations in the midcontinent of the U.S. The analysis indicates that the potentiometric surface is more readily defined through human interpretation of the chaotic DST data sets rather than through the application of filtering and geostatistical analysis. The data are viewed as a series of narrow, 400-mile-long swaths and a 2D viewer is used to select a subset of hydraulic-head values that represent the potentiometric surface. The user-selected subsets for each swath are then combined into one data set for each formation. These data are then joined with the hydraulic-head values from water wells to define the 3D potentiometric surfaces. The final product is an interactive, 3D digital display containing: (1) the subsurface structure of the formation, (2) the cluster of DST-derived hydraulic head values, (3) the user-selected subset of hydraulic-head values that define the potentiometric surface, (4) the hydraulic-head measurements from the corresponding shallow aquifer, (5) the resulting potentiometric surface encompassing both oil and gas and water wells, and (6) the land surface elevation of the region. Examples from the midcontinent of the United States, specifically Kansas, Oklahoma, and parts of adjacent states illustrate the process.

Experimental and kinetic modeling investigation of rich premixed toluene flames doped with n-butanol.

PubMed

Li, Yuyang; Yuan, Wenhao; Li, Tianyu; Li, Wei; Yang, Jiuzhong; Qi, Fei

2018-04-25

n-Butanol is a promising renewable biofuel and has a lot of advantages as a gasoline additive compared with ethanol. Though the combustion of pure n-butanol has been extensively investigated, the chemical structures of large hydrocarbons doped with n-butanol, especially for aromatic fuels, are still insufficiently understood. In this work, rich premixed toluene/n-butanol/oxygen/argon flames were investigated at 30 Torr with synchrotron vacuum ultraviolet photoionization mass spectrometry (SVUV-PIMS). The blending ratio of n-butanol was varied from 0 to 50%, while the equivalence ratio was maintained at a quite rich value (1.75) for the purpose of studying the influence of n-butanol on the aromatic growth process. Flame species including radicals, reactive molecules, isomers and polycyclic aromatic hydrocarbons (PAHs) were identified and their mole fraction profiles were measured. A kinetic model of toluene/n-butanol combustion was developed from our recently reported toluene and n-butanol models. It is observed that the production of most toluene decomposition products and larger aromatics was suppressed as the blending ratio of n-butanol increases. Meanwhile, the addition of n-butanol generally enhanced the formation of most observed C2-C4 hydrocarbons and C1-C4 oxygenated species. The rate of production (ROP) analysis and experimental observations both indicate that the interaction between toluene and n-butanol in their decomposition processes mainly occurs at the formation of small intermediates, e.g. acetylene and methyl. In particular, the interaction between toluene and n-butanol in methyl formation influences the formation of large monocyclic aromatics such as ethylbenzene, styrene and phenylacetylene, making their maximum mole fractions decay slowly upon increasing the blending ratio of n-butanol compared with toluene and benzyl. The increase of the blending ratio of n-butanol reduces the formation of key PAH precursors such as benzyl, fulvenallenyl, benzene, phenyl and propargyl, which leads to a remarkable reduction in the formation of PAHs.

Current Status and Bioinspired Perspective of Electrochemical Conversion of CO2 to a Long-Chain Hydrocarbon.

PubMed

Yang, Ki Dong; Lee, Chan Woo; Jin, Kyoungsuk; Im, Sang Won; Nam, Ki Tae

2017-01-19

Electrocatalytic conversion of CO 2 into a long-chain hydrocarbon represents an important research direction in adding value to CO 2 -based chemicals and realizing its practical application. Long-chain hydrocarbons may change the current fossil fuel-based industry in that those chemicals have a similar energy density as gasoline, high compatibility with the current infrastructure, and low hydroscopicity for pipeline distribution. However, most of the electrocatalysts produce C 1 , C 2 , and C 3 chemicals, and methods for producing long-chain hydrocarbons are not available thus far. Interestingly, nature utilizes many enzymes to generate long-chain hydrocarbons using C 2 building blocks and suggests key mechanisms, inspiring new perspective in the design of electrocatalysts. In this Perspective, we present case studies to demonstrate how CO 2 and its reductive derivatives interact with the electrode surface during C-C bond formation and introduce how these issues are addressed in biological systems. We end this Perspective by outlining possible strategies to translate the natural mechanism into a heterogeneous electrode.

Nile Red Detection of Bacterial Hydrocarbons and Ketones in a High-Throughput Format

PubMed Central

Pinzon, Neissa M.; Aukema, Kelly G.; Gralnick, Jeffrey A.; Wackett, Lawrence P.

2011-01-01

ABSTRACT A method for use in high-throughput screening of bacteria for the production of long-chain hydrocarbons and ketones by monitoring fluorescent light emission in the presence of Nile red is described. Nile red has previously been used to screen for polyhydroxybutyrate (PHB) and fatty acid esters, but this is the first report of screening for recombinant bacteria making hydrocarbons or ketones. The microtiter plate assay was evaluated using wild-type and recombinant strains of Shewanella oneidensis and Escherichia coli expressing the enzyme OleA, previously shown to initiate hydrocarbon biosynthesis. The strains expressing exogenous Stenotrophomonas maltophilia oleA, with increased levels of ketone production as determined by gas chromatography-mass spectrometry, were distinguished with Nile red fluorescence. Confocal microscopy images of S. oneidensis oleA-expressing strains stained with Nile red were consistent with a membrane localization of the ketones. This differed from Nile red staining of bacterial PHB or algal lipid droplets that showed intracellular inclusion bodies. These results demonstrated the applicability of Nile red in a high-throughput technique for the detection of bacterial hydrocarbons and ketones. PMID:21712420

Positron induced scattering cross sections for hydrocarbons relevant to plasma

NASA Astrophysics Data System (ADS)

Singh, Suvam; Antony, Bobby

2018-05-01

This article explores positron scattering cross sections by simple hydrocarbons such as ethane, ethene, ethyne, propane, and propyne. Chemical erosion processes occurring on the surface due to plasma-wall interactions are an abundant source of hydrocarbon molecules which contaminate the hydrogenic plasma. These hydrocarbons play an important role in the edge plasma region of Tokamak and ITER. In addition to this, they are also one of the major components in the planetary atmospheres and astrophysical mediums. The present work focuses on calculation of different positron impact interactions with simple hydrocarbons in terms of the total cross section (Qtot), elastic cross section (Qel), direct ionization cross section (Qion), positronium formation cross section (Qps), and total ionization cross section (Qtion). Knowing that the positron-plasma study is one of the trending fields, the calculated data have diverse plasma and astrophysical modeling applications. A comprehensive study of Qtot has been provided where the inelastic cross sections have been reported for the first time. Comparisons are made with those available from the literature, and a good agreement is obtained with the measurements.

Controlled field study on the use of nitrate and oxygen for bioremediation of a gasoline source zone

USGS Publications Warehouse

Barbaro, J.R.; Barker, J.F.

2000-01-01

Controlled releases of unleaded gasoline were utilized to evaluate the biotransformation of the soluble aromatic hydrocarbons (benzene, toluene, ethylbenzene, xylene isomers, trimethylbenzene isomers, and naphthalene) within a source zone using nitrate and oxygen as electron acceptors. Experiments were conducted within two 2 m ?? 2 m ?? 3.5 m deep sheet-piling cells. In each treatment cell, a gasoline-contaminated zone was created below the water table. Groundwater amended with electron acceptors was then flushed continuously through the cells for 174 day. Electron-acceptor utilization and hydrocarbon-metabolite formation were noted in both cells, indicating that some microbial activity had been induced in response to flushing. Relative to the cell residence time, nitrate utilization was slow and aromatic-hydrocarbon mass losses in response to microaerophilic dissolved oxygen addition were not obvious under these in situ conditions. There was relatively little biotransformation of the aromatic hydrocarbons over the 2-m flow path monitored in this experiment. A large denitrifying population capable of aromatic hydrocarbon biotransformation failed to develop within the gasoline source zone over a 14-mo period of nitrate exposure.

Thermally-driven Coupled THM Processes in Shales

NASA Astrophysics Data System (ADS)

Rutqvist, J.

2017-12-01

Temperature changes can trigger strongly coupled thermal-hydrological-mechanical (THM) processes in shales that are important to a number of subsurface energy applications, including geologic nuclear waste disposal and hydrocarbon extraction. These coupled processes include (1) direct pore-volume couplings, by thermal expansion of trapped pore-fluid that triggers instantaneous two-way couplings between pore fluid pressure and mechanical deformation, and (2) indirect couplings in terms of property changes, such as changes in mechanical stiffness, strength, and permeability. Direct pore-volume couplings have been studied in situ during borehole heating experiments in shale (or clay stone) formations at Mont Terri and Bure underground research laboratories in Switzerland and France. Typically, the temperature changes are accompanied with a rapid increase in pore pressure followed by a slower decrease towards initial (pre-heating) pore pressure. Coupled THM modeling of these heater tests shows that the pore pressure increases because the thermal expansion coefficient of the fluid is much higher than that of the porous clay stone. Such thermal pressurization induces fluid flow away from the pressurized area towards areas of lower pressure. The rate of pressure increase and magnitude of peak pressure depends on the rate of heating, pore-compressibility, and permeability of the shale. Modeling as well as laboratory experiments have shown that if the pore pressure increase is sufficiently large it could lead to fracturing of the shale or shear slip along pre-existing bedding planes. Another set of data and observations have been collected associated with studies related to concentrated heating and cooling of oil-shales and shale-gas formations. Heating may be used to enhance production from tight oil-shale, whereas thermal stimulation has been attempted for enhanced shale-gas extraction. Laboratory experiments on shale have shown that strength and elastic deformation modulus decreases with temperature while the rate creep deformations increase with temperature. Such temperature dependency also affects the well stability and zonal sealing across shale layers.

The influence of pressure on petroleum generation and maturation as suggested by aqueous pyrolysis

USGS Publications Warehouse

Price, L.C.; Wenger, L.M.

1992-01-01

Because fluid pressures are transient in sedimentary basins over geologic time, the effect of increasing fluid pressure on organic-matter metamorphism is difficult to determine, and conflicting opinions exist concerning its influence. Properly-performed aqueous-pyrolysis experiments can closely simulate hydrocarbon generation and maturation in nature, and thus offer an excellent way to study the influence of pressure. Such experiments, carried out on the Retort Phosphatic Shale Member of the Lower Permian Phosphoria Formation (type II-S organic matter) at different constant temperatures, demonstrated that increasing pressure significantly retards all aspects of organic matter metamorphism, including hydrocarbon generation, maturation and thermal destruction. This conclusion results from detailed quantitative and qualitative analyses of all products from hydrocarbon generation, from the C1 to C4 hydrocarbon gases to the asphaltenes, and also from analyses of the reacted rocks. We have documented that our aqueous-pyrolysis experiments closely simulated natural hydrocarbon generation and maturation. Thus the data taken as a function of pressure have relevance to the influence of normal and abnormal fluid pressures as related to: 1) depths and temperatures of mainstage hydrocarbon generation; 2) the thermal destruction of deposits of gas or light oil, or their preservation to unexpectedly high maturation ranks; and 3) the persistence of measurable to moderate concentrations of C15+ hydrocarbons in fine-grained rocks even to ultra-high maturation ranks. ?? 1992.

Interlake production established using quantitative hydrocarbon well-log analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lancaster, J.; Atkinson, A.

1988-07-01

Production was established in a new pay zone of the basal Interlake Formation adjacent to production in Midway field in Williams County, North Dakota. Hydrocarbon saturation, which was computed using hydrocarbon well-log (mud-log) data, and computed permeability encouraged the operator to run casing and test this zone. By use of drilling rig parameters, drilling mud properties, hydrocarbon-show data from the mud log, drilled rock and porosity descriptions, and wireline log porosity, this new technique computes oil saturation (percent of porosity) and permeability to the invading filtrate, using the Darcy equation. The Leonardo Fee well was drilled to test the Devonianmore » Duperow, the Silurian upper Interlake, and the Ordovician Red River. The upper two objectives were penetrated downdip from Midway production and there were no hydrocarbon shows. It was determined that the Red River was tight, based on sample examination by well site personnel. The basal Interlake, however, liberated hydrocarbon shows that were analyzed by this new technology. The results of this evaluation accurately predicted this well would be a commercial success when placed in production. Where geophysical log analysis might be questionable, this new evaluation technique may provide answers to anticipated oil saturation and producibility. The encouraging results of hydrocarbon saturation and permeability, produced by this technique, may be largely responsible for the well being in production today.« less

Recent Developments in the Addition of Phosphinylidene-Containing Compounds to Unactivated Unsaturated Hydrocarbons: Phosphorus-Carbon Bond-Formation via Hydrophosphinylation and Related Processes

PubMed Central

Coudray, Laëtitia

2012-01-01

Summary The reactions of phosphinylidene-containing compounds with unactivated unsaturated hydrocarbons are reviewed. The review is organized by phosphorus-containing functional group types. Free-radical and metal-catalyzed additions of R1R2P(O)H to alkenes, alkynes, and related compounds, deliver functionalized organophosphorus compounds RP(O)R1R2, including H-phosphinates, phosphinates, tertiary phosphine oxides, and phosphonates. The review covers the literature up to February 2008. PMID:23308039

Effects of oil and dispersant on formation of marine oil snow and transport of oil hydrocarbons.

PubMed

Fu, Jie; Gong, Yanyan; Zhao, Xiao; O'Reilly, S E; Zhao, Dongye

2014-12-16

This work explored the formation mechanism of marine oil snow (MOS) and the associated transport of oil hydrocarbons in the presence of a stereotype oil dispersant, Corexit EC9500A. Roller table experiments were carried out to simulate natural marine processes that lead to formation of marine snow. We found that both oil and the dispersant greatly promoted the formation of MOS, and MOS flocs as large as 1.6-2.1 mm (mean diameter) were developed within 3-6 days. Natural suspended solids and indigenous microorganisms play critical roles in the MOS formation. The addition of oil and the dispersant greatly enhanced the bacterial growth and extracellular polymeric substance (EPS) content, resulting in increased flocculation and formation of MOS. The dispersant not only enhanced dissolution of n-alkanes (C9-C40) from oil slicks into the aqueous phase, but facilitated sorption of more oil components onto MOS. The incorporation of oil droplets in MOS resulted in a two-way (rising and sinking) transport of the MOS particles. More lower-molecular-weight (LMW) n-alkanes (C9-C18) were partitioned in MOS than in the aqueous phase in the presence of the dispersant. The information can aid in our understanding of dispersant effects on MOS formation and oil transport following an oil spill event.

Development and applications of ruggedized VIS/NIR spectrometer system for oilfield wellbores

NASA Astrophysics Data System (ADS)

Fujisawa, Go; Yamate, Tsutomu

2013-12-01

The development and applications of a ruggedized visible to near-infrared (VIS/NIR) spectrometer system capable of measuring fluid spectra in oilfield wellbores are presented. Real-time assessment of formation fluid properties penetrated by an oilfield wellbore is critically important for oilfield operating companies to make informed decisions to optimize the development plan of the well and hydrocarbon reservoir. A ruggedized VIS/NIR spectrometer was designed and built to measure and analyze hydrocarbon spectra reliably under the harsh conditions of the oilfield wellbore environment, including temperature up to 175 °C, pressure up to 170 MPa, and severe mechanical shocks and vibrations. The accuracy of hydrocarbon group composition analysis was compared well with gas chromatography results in the laboratory.

Assessment of Undiscovered Oil and Gas Resources of the Uinta-Piceance Province of Colorado and Utah, 2002

USGS Publications Warehouse

,

2002-01-01

The U.S. Geological Survey (USGS) recently completed an assessment of the undiscovered oil and gas potential of the UintaPiceance Province of northwestern Colorado and northeastern Utah (fig. 1). The assessment of the Uinta-Piceance Province is geology based and uses the Total Petroleum System concept. The geologic elements of Total Petroleum Systems include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy, petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five Total Petroleum Systems and 20 Assessment Units within these Total Petroleum Systems, and quantitatively estimated the undiscovered oil and gas resources within each Assessment Unit (table 1).

Chemical Aspects of Astrophysically Observed Extraterrestrial Methanol, Hydrocarbon Derivatives, and Ions.

PubMed

Olah, George A; Mathew, Thomas; Prakash, G K Surya; Rasul, Golam

2016-02-10

Astrophysically observed extraterrestrial molecular matter contains, besides hydrogen and water, methane and methanol as the most abundant species. Feasible pathways and chemical aspects of their formation as well as of derived hydrocarbon homologues and their ions (carbocations and carbanions) are discussed on the basis of observed similarities with our studied terrestrial chemistry. The preferred pathway for converting extraterrestrial methane according to Ali et al. is based on CH5(+) and Olah's related nonclassical carbonium ion chemistry. On the basis of the observed higher reactivity of methanol compared with methane in various chemical reactions, a feasible new pathway is proposed for the conversion of extraterrestrial methanol to hydrocarbons, their derivatives, and carbocations together with a possible connection with methonium ion-based chemistry.

Promotional Effects of In on Non-Oxidative Methane Transformation Over Mo-ZSM-5

DOE PAGES

Zhang, Yang; Kidder, Michelle; Ruther, Rose E.; ...

2016-08-16

In this paper, we present a new class of catalysts, InMo-ZSM- 5, which can be prepared by indium impregnation of Mo-ZSM- 5. The incorporation of indium dramatically decreases coke formation during methane dehydroaromatization. The benzene and C 2 hydrocarbons selectivity among total hydrocarbons over InMo-ZSM- 5 remains comparable to that of Mo-ZSM- 5 despite reduced methane conversion due to decreased coke formation. We found 1 wt% indium to be optimal loading for reducing coke selectivity to half that of Mo-ZSM- 5. Characterization methods were not helpful in discerning the interaction of In with Mo but experiments with bimetallic 1In2Mo-ZSM- 5more » and mechanical mixture 1In+2Mo-ZSM- 5 suggest that In and Mo need to be in close proximity to suppress coke formation. Finally, this is supported by temperature programmed reduction experiments which show that In incorporation leads to lower Mo reduction temperature in In2Mo-ZMS- 5.« less

Siberian Platform: Geology and Natural Bitumen Resources

USGS Publications Warehouse

Meyer, Richard F.; Freeman, P.A.

2006-01-01

Summary: The Siberian platform is located between the Yenisey River on the west and the Lena River on the south and east. The Siberian platform is vast in size and inhospitable in its climate. This report is concerned principally with the setting, formation, and potential volumes of natural bitumen. In this report the volumes of maltha and asphalt referred to in the Russian literature are combined to represent natural bitumen. The generation of hydrocarbons and formation of hydrocarbon accumulations are discussed. The sedimentary basins of the Platform are described in terms of the Klemme basin classification system and the conditions controlling formation of natural bitumen. Estimates of in-place bitumen resources are reviewed and evaluated. If the bitumen volume estimate is confined to parts of identified deposits where field observations have verified rock and bitumen grades values, the bitumen resource amounts to about 62 billion barrels of oil in-place. However, estimates of an order of magnitude larger can be obtained if additional speculative and unverified rock volumes and grade measures are included.

Chemical reaction and dust formation studies in laboratory hydrocarbon plasmas.

NASA Astrophysics Data System (ADS)

Hippler, Rainer; Majumdar, Abhijit; Thejaswini, H. C.

Plasma chemical reaction studies with relevance to, e.g., Titan's atmosphere have been per-formed in various laboratory plasmas [1,2]. Chemical reactions in a dielectric barrier discharge at medium pressure of 250-300 mbar have been studied in CH4 /N2 and CH4 /Ar gas mixtures by means of mass spectrometry. The main reaction scheme is production of H2 by fragmenta-tion of CH4 , but also production of larger hydrocarbons like Cn Hm with n up to 10 including formation of different functional CN groups is observed. [1] A. Majumdar and R. Hippler, Development of dielectric barrier discharge plasma processing apparatus for mass spectrometry and thin film deposition, Rev. Sci. Instrum. 78, 075103 (2007) [2] H.T. Do, G. Thieme, M. Frühlich, H. Kersten, and R. Hippler, Ion Molecule and Dust Particle Formation in Ar/CH4 , Ar/C2 H2 and Ar/C3 H6 Radio-frequency Plasmas, Contrib. Plasma Phys. 45, No. 5-6, 378-384 (2005)

FORMATION OF POLYCYCLIC AROMATIC HYDROCARBONS AND CARBONACEOUS SOLIDS IN GAS-PHASE CONDENSATION EXPERIMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaeger, C.; Huisken, F.; Henning, Th.

2009-05-01

Carbonaceous grains represent a major component of cosmic dust. In order to understand their formation pathways, they have been prepared in the laboratory by gas-phase condensation reactions such as laser pyrolysis and laser ablation. Our studies demonstrate that the temperature in the condensation zone determines the formation pathway of carbonaceous particles. At temperatures lower than 1700 K, the condensation by-products are mainly polycyclic aromatic hydrocarbons (PAHs) that are also the precursors or building blocks for the condensing soot grains. The low-temperature condensates contain PAH mixtures that are mainly composed of volatile three to five ring systems. At condensation temperatures highermore » than 3500 K, fullerene-like carbon grains and fullerene compounds are formed. Fullerene fragments or complete fullerenes equip the nucleating particles. Fullerenes can be identified as soluble components. Consequently, condensation products in cool and hot astrophysical environments such as cool and hot asymptotic giant branch stars or Wolf-Rayet stars should be different and should have distinct spectral properties.« less

Geoengineering Research for a Deep Underground Science and Engineering Laboratory in Sedimentary Rock

NASA Astrophysics Data System (ADS)

Mauldon, M.

2004-12-01

A process to identify world-class research for a Deep Underground Science and Engineering Laboratory (DUSEL) in the USA has been initiated by NSF. While allowing physicists to study, inter alia, dark matter and dark energy, this laboratory will create unprecedented opportunities for biologists to study deep life, geoscientists to study crustal processes and geoengineers to study the behavior of rock, fluids and underground cavities at depth, on time scales of decades. A substantial portion of the nation's future infrastructure is likely to be sited underground because of energy costs, urban crowding and vulnerability of critical surface facilities. Economic and safe development of subsurface space will require an improved ability to engineer the geologic environment. Because of the prevalence of sedimentary rock in the upper continental crust, much of this subterranean infrastructure will be hosted in sedimentary rock. Sedimentary rocks are fundamentally anisotropic due to lithology and bedding, and to discontinuities ranging from microcracks to faults. Fractures, faults and bedding planes create structural defects and hydraulic pathways over a wide range of scales. Through experimentation, observation and monitoring in a sedimentary rock DUSEL, in conjunction with high performance computational models and visualization tools, we will explore the mechanical and hydraulic characteristics of layered rock. DUSEL will permit long-term experiments on 100 m blocks of rock in situ, accessed via peripheral tunnels. Rock volumes will be loaded to failure and monitored for post-peak behavior. The response of large rock bodies to stress relief-driven, time-dependent strain will be monitored over decades. Large block experiments will be aimed at measurement of fluid flow and particle/colloid transport, in situ mining (incl. mining with microbes), remediation technologies, fracture enhancement for resource extraction and large scale long-term rock mass response to induced stresses - with parallel geophysical imaging of the rock mass (and subsequent verification) flow and transport processes, and time-dependent stress and strain. An experimental advantage of sedimentary rock is the presence of pervasive mechanical interfaces (bedding planes), which suggest a host of experimental designs on large rock blocks and slabs (induced flexure, shear strength of interfaces, etc). Thus DUSEL will enable fundamental research about the behavior of a layered rock mass - the dominant structural architecture in near-surface environments worldwide. A further benefit is the natural suitability of sedimentary rocks for experiments related to oil and gas production, or to CO2 sequestration. For example, fluid-induced fracturing of sedimentary rock has long been used by the hydrocarbon industry to improve oil and coal bed methane recovery. Since some fracturing agents are potential contaminants, a major concern and legal responsibility in the US is ensuring the integrity of nearby aquifers. Hydraulic fracturing from a sedimentary rock DUSEL will be followed by injection of low viscosity grout. The rock mass will then be mined back to expose network characteristics of the induced hydraulic fractures. Key questions related to hydrocarbon extraction, CO2 sequestration, waste isolation, and remediation of subsurface contaminants depend critically on the connectivity and architecture of fractures and on coupled thermal, hydrological, mechanical and chemical processes. Fluid flow, particle transport and reaction transport processes are coupled to the stress across fractures, and to thermal, chemical and hydraulic gradients. All can best be studied via large block tests in a subterranean laboratory, ideally in a sedimentary environment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This paper reports a coral reef formation theory that has implications for hydrocarbon exploration. The theory states that many coral reefs and carbonate buildups from at and are dependent upon nutrient rich fluids seeping through the seabed.

FORMATION AND PERSISTANCE OF DNA ADDUCTS IN THE LIVER OF BROWN BULLHEADS EXPOSED TO BENZO(A)PYRENE

EPA Science Inventory

The formation and persistence of benzo[a]pyrene (BP)-DNA adducts in the liver of brown bullheads (Ictalurus nebulosus) treated with the hydrocarbon (20 mg/kg body wt, i.p.) was investigated using the 32P-postlabeling assay. he highest level of covalent binding of BP to liver DNA ...

Prospects of oil field development in Tomsk region

NASA Astrophysics Data System (ADS)

Il'ina, M. N.; Il'ina, G. F.

2017-12-01

The article describes the geologic structure of the formation located not far from Strezhevoy, Tomsk Oblast. The formation has been poorly studied by seismic methods. The reserves categories C1 and C2 as well as hydrocarbon potential are presented. 4 exploratory and 39 production wells are designed to be drilled depending on geologic knowledge and formation conditions. The article deals with the investment plan including development, oil export expenditures and implementing cost calculation.

Artificial maturation of an immature sulfur- and organic matter-rich limestone from the Ghareb Formation, Jordan

USGS Publications Warehouse

Koopmans, M.P.; Rijpstra, W.I.C.; De Leeuw, J. W.; Lewan, M.D.; Damste, J.S.S.

1998-01-01

An immature (Ro=0.39%), S-rich (S(org)/C = 0.07), organic matter-rich (19.6 wt. % TOC) limestone from the Ghareb Formation (Upper Cretaceous) in Jordan was artificially matured by hydrous pyrolysis (200, 220 ..., 300??C; 72 h) to study the effect of progressive diagenesis and early catagenesis on the amounts and distributions of hydrocarbons, organic sulfur compounds and S-rich geomacromolecules. The use of internal standards allowed the determination of absolute amounts. With increasing thermal maturation, large amounts of alkanes and alkylthiophenes with predominantly linear carbon skeletons are generated from the kerogen. The alkylthiophene isomer distributions do not change significantly with increasing thermal maturation, indicating the applicability of alkylthiophenes as biomarkers at relatively high levels of thermal maturity. For a given carbon skeleton, the saturated hydrocarbon, alkylthiophenes and alkylbenzo[b]thiophenes are stable forms at relatively high temperatures, whereas the alkylsulfides are not stable. The large amount of alkylthiophenes produced relative to the alkanes may be explained by the large number of monosulfide links per carbon skeleton. These results are in good agreement with those obtained previously for an artificial maturation series of an immature S-rich sample from the Gessoso-solfifera Formation.An immature (Ro = 0.39%), S-rich (Sorg/C = 0.07), organic matter-rich (19.6 wt.% TOC) limestone from the Ghareb Formation (Upper Cretaceous) in Jordan was artificially matured by hydrous pyrolysis (200, 220, ..., 300??C; 72 h) to study the effect of progressive diagenesis and early catagenesis on the amounts and distributions of hydrocarbons, organic sulfur compounds and S-rich geomacromolecules. The use of internal standards allowed the determination of absolute amounts. With increasing thermal maturation, large amounts of alkanes and alkylthiophenes with predominantly linear carbon skeletons are generated from the kerogen. The alkylthiophene isomer distributions do not change significantly with increasing thermal maturation, indicating the applicability of alkylthiophenes as biomarkers at relatively high levels of thermal maturity. For a given carbon skeleton, the saturated hydrocarbon, alkylthiophene and alkylbenzo[b]thiophenes are stable forms at relatively high temperatures, whereas the alkylsulfides are not stable. The large amount of alkylthiophenes produced relative to the alkanes may be explained by the large number of monosulfide links per carbon skeleton. These results are in good agreement with those obtained previously for an artificial maturation series of an immature S-rich sample from the Gessoso-solfifera Formation.

Observations of the release of non-methane hydrocarbons from fractured shale.

PubMed

Sommariva, Roberto; Blake, Robert S; Cuss, Robert J; Cordell, Rebecca L; Harrington, Jon F; White, Iain R; Monks, Paul S

2014-01-01

The organic content of shale has become of commercial interest as a source of hydrocarbons, owing to the development of hydraulic fracturing ("fracking"). While the main focus is on the extraction of methane, shale also contains significant amounts of non-methane hydrocarbons (NMHCs). We describe the first real-time observations of the release of NMHCs from a fractured shale. Samples from the Bowland-Hodder formation (England) were analyzed under different conditions using mass spectrometry, with the objective of understanding the dynamic process of gas release upon fracturing of the shale. A wide range of NMHCs (alkanes, cycloalkanes, aromatics, and bicyclic hydrocarbons) are released at parts per million or parts per billion level with temperature- and humidity-dependent release rates, which can be rationalized in terms of the physicochemical characteristics of different hydrocarbon classes. Our results indicate that higher energy inputs (i.e., temperatures) significantly increase the amount of NMHCs released from shale, while humidity tends to suppress it; additionally, a large fraction of the gas is released within the first hour after the shale has been fractured. These findings suggest that other hydrocarbons of commercial interest may be extracted from shale and open the possibility to optimize the "fracking" process, improving gas yields and reducing environmental impacts.

Sequence stratigraphy and hydrocarbon habitat of the Natih formation in Oman

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sikkema, W.; Borgomano, J.

1993-09-01

The Natih Formation is part of the Mesozoic platform carbonate succession deposited on the southeastern Arabian peninsula and one of the main hydrocarbon producing reservoirs in Oman. It is separated from the underlying carbonates of the Shuaiba Formation by the Nahr Umr Formation and is overlain by the Fiqa Formation, both acting as regional seals. The age of the Natih Formation is late Albian to early Turonian, and its deposition was terminated by early Turonian uplift. Various lithofacies are present in the Natih Formation. The Natih Formation is cyclic, with a succession of coarsening-upward cycles of deeper marine shales andmore » mudstones grading to shallow marine rudistid packstones and grainstones, each terminated by an emergence surface. The cyclicity is the result of eustatic sea level changes. Two deeper marine shales rich in planktonic foraminifera and organic material are intercalated within the sequence. The cycles have been used to subdivide the Natih into members labeled a to g. A sequence stratigraphic model has been applied to the observed cyclicity, which helps to understand (1) the distribution of shallow marine grainstones (reservoir) and deeper marine shales and mudstones (seal, source rock), and (2) where the reservoir quality may have been enhanced by emergence and leaching. The model has been tested both on a regional scale and on a field scale, e.g., on seismic lines over the Sirat Prospect area in central north Oman and the Marmul area of south Oman.« less

Geomechanical response to seasonal gas storage in depleted reservoirs: A case study in the Po River basin, Italy

NASA Astrophysics Data System (ADS)

Teatini, P.; Castelletto, N.; Ferronato, M.; Gambolati, G.; Janna, C.; Cairo, E.; Marzorati, D.; Colombo, D.; Ferretti, A.; Bagliani, A.; Bottazzi, F.

2011-06-01

Underground gas storage (UGS) in depleted hydrocarbon reservoirs is a strategic practice to cope with the growing energy demand and occurs in many places in Europe and North America. In response to summer gas injection and winter gas withdrawal the reservoir expands and contracts essentially elastically as a major consequence of the fluid (gas and water) pore pressure fluctuations. Depending on a number of factors, including the reservoir burial depth, the difference between the largest and the smallest gas pore pressure, and the geomechanical properties of the injected formation and the overburden, the porous medium overlying the reservoir is subject to three-dimensional deformation with the related cyclic motion of the land surface being both vertical and horizontal. We present a methodology to evaluate the environmental impact of underground gas storage and sequestration from the geomechanical perspective, particularly in relation to the ground surface displacements. Long-term records of injected and removed gas volume and fluid pore pressure in the "Lombardia" gas field, northern Italy, are available together with multiyear detection of vertical and horizontal west-east displacement of the land surface above the reservoir by an advanced permanent scatterer interferometric synthetic aperture radar (PSInSAR) analysis. These data have been used to calibrate a 3-D fluid-dynamic model and develop a 3-D transversally isotropic geomechanical model. The latter has been successfully implemented and used to reproduce the vertical and horizontal cyclic displacements, on the range of 8-10 mm and 6-8 mm, respectively, measured between 2003 and 2007 above the reservoir where a UGS program has been underway by Stogit-Eni S.p.A. since 1986 following a 5 year field production life. Because of the great economical interest to increase the working gas volume as much as possible, the model addresses two UGS scenarios where the gas pore overpressure is pushed from the current 103%pi, where pi is the gas pore pressure prior to the field development, to 107%pi and 120%pi. Results of both scenarios show that there is a negligible impact on the ground surface, with deformation gradients that remain well below the most restrictive admissible limits for the civil structures and infrastructures.

Production from multiple zones of a tar sands formation

DOEpatents

Karanikas, John Michael; Vinegar, Harold J

2013-02-26

A method for treating a tar sands formation includes providing heat to at least part of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat is allowed to transfer from the heaters to at least a portion of the formation. Fluids are produced from the formation through at least one production well that is located in at least two zones in the formation. The first zone has an initial permeability of at least 1 darcy. The second zone has an initial of at most 0.1 darcy. The two zones are separated by a substantially impermeable barrier.

Greek Myths: 8 Short Plays for the Classroom.

ERIC Educational Resources Information Center

Rearick, John

Noting that myths are a powerful classroom tool, this book presents 8 short plays (in a readers' theater format) for grades 4-8. After an introduction that discusses getting started and using the book, plays in the book are: (1) "The Gods Must Be Crazy: The Story of Cupid and Psyche"; (2) "The Sound of Music Goes Underground: The…

Going Underground: A Field Investigation and Lab Activity on Karst Topography and Water Systems

ERIC Educational Resources Information Center

O'Dell, Gary; Gonzalez-Espada, Wilson

2011-01-01

Students learn science best with activities that mirror the way scientists work. This article describes how geologists investigate groundwater flow systems in areas of karst topography--geologic formations shaped by dissolving bedrock--and provides a way for students to replicate this research. Students also use electric current to model water…

77 FR 25205 - Proposed Extension of Existing Information Collection; Roof Control Plans for Underground Coal Mines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-27

... assure that requested data can be provided in the desired format, reporting burden (time and financial... request on September 28, 2009. The package expires on September 30, 2012. DATES: All comments must be... safety and health standards. MSHA has updated the data in respect to the number of respondents and...

A model for migration and accumulation of hydrocarbons in the Thamama and Arab reservoirs in Abu Dhabi, U.A.E.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hawas, M.F.; Takezaki, H.

1995-08-01

The distribution of hydrocarbons in the Lower Cretaceous Thamama Group and Upper Jurassic Arab Formation in Abu Dhabi is influenced by the development of the intervening Hith anhydrites. The geochemical analysis of Thamama and Arab hydrocarbons indicate that they were generated from a common source rock: the Upper Jurassic Diyab Formation. Studies carried out on the Miocene sabkha anhydrites in the coastal flat west of Abu Dhabi supported a model for vertical migration through the Hith anhydrites under certain conditions. The established model implies that the Diyab oil and gas had migrated essentially vertically and individually which means that themore » oil migrated prior to the gas and their distribution is controlled by the differential sealing potential of the anhydrites at each migration phase: a Hith anhydrite bed of more than 30 feet (ft.) thick was a perfect seal for hydrocarbon migration into the Arab reservoirs. In this case, oils could not break through to the overlying Thamama group. But where the anhydride bed thicknesses dropped below 30 ft. thick, this permitted oil migration through to the overlying Thamama reservoirs during the oil generation phase in the Turonian time. At a later stage, with additional depth of burial and progressive diagenesis anhydrite beds as thin as 8 ft. thick became effective seals. These controlled the distribution of the gas during the gas generation phase in the Eocene time.« less

Cigeo, the French Geological Repository Project - 13022

DOE Office of Scientific and Technical Information (OSTI.GOV)

Labalette, Thibaud; Harman, Alain; Dupuis, Marie-Claude

The Cigeo industrial-scale geological disposal centre is designed for the disposal of the most highly-radioactive French waste. It will be built in an argillite formation of the Callovo-Oxfordian dating back 160 million years. The Cigeo project is located near the Bure village in the Paris Basin. The argillite formation was studied since 1974, and from the Meuse/Haute-Marne underground research laboratory since end of 1999. Most of the waste to be disposed of in the Cigeo repository comes from nuclear power plants and from reprocessing of their spent fuel. (authors)

Formation of polycyclic aromatic hydrocarbons in circumstellar envelopes

NASA Technical Reports Server (NTRS)

Frenklach, Michael; Feigelson, Eric D.

1989-01-01

Production of polycyclic aromatic hydrocarbons in carbon-rich circumstellar envelopes was investigated using a kinetic approach. A detailed chemical reaction mechanism of gas-phase PAH formation and growth, containing approximately 100 reactions of 40 species, was numerically solved under the physical conditions expected in cool stellar winds. The chemistry is based on studies of soot production in hydrocarbon pyrolysis and combustion. Several first-ring and second-ring cyclization processes were considered. A linear lumping algorithm was used to describe PAH growth beyond the second aromatic ring. PAH production using this mechanism was examined with respect to a grid of idealized constant velocity stellar winds as well as several published astrophysical models. The basic result is that the onset of PAH production in the interstellar envelopes is predicted to occur within the temperature interval of 1100 to 900 K. The absolute amounts of the PAHs formed, however, are very sensitive to a number of parameters, both chemical and astrophysical, whose values are not accurately known. Astrophysically meaningful quantities of PAHs require particularly dense and slow stellar winds and high initial acetylene abundance. It is suggested that most of the PAHs may be produced in a relatively small fraction of carbon-rich red giants.

Chemical and biological monitoring of MIOR on the pilot area of Vyngapour oil field, West Sibera, Russia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arinbasarov, M.U.; Murygina, V.P.; Mats, A.A.

1995-12-31

The pilot area of the Vyngapour oil field allotted for MIOR tests contains three injection and three producing wells. These wells were treated in summer 1993 and 1994. Before, during, and after MIOR treatments on the pilot area the chemical compounds of injected and formation waters were studied, as well as the amount and species of microorganisms entering the stratum with the injected water and indigenous bacteria presented in bottomhole zones of the wells. The results of monitoring showed that the bottomhole zone of the injection well already had biocenosis of heterotrophic, hydrocarbon-oxidizing, methanogenic, and sulfate-reducing bacteria, which were besidesmore » permanently introduced into the reservoir during the usual waterflooding. The nutritious composition activated vital functions of all bacterial species presented in the bottomhole zone of the injection well. The formation waters from producing wells showed the increase of the content of nitrate, sulfate, phosphate, and bicarbonate ions by the end of MIOR. The amount of hydrocarbon-oxidizing bacteria in formation waters of producing wells increased by one order. The chemical and biological monitoring revealed the activation of the formation microorganisms, but no transport of food industry waste bacteria through the formation from injection to producing wells was found.« less

Formation of hydrocarbon compounds during the hydrocracking of non-edible vegetable oils with cobalt-nickel supported on hierarchical HZSM-5 catalyst

NASA Astrophysics Data System (ADS)

Marlinda, L.; Al-Muttaqii, M.; Roesyadi, A.; Prajitno, D. H.

2017-05-01

The hierarchical Co-Ni/HZSM-5 catalyst with hierarchical pore structure was prepared by desilication and incipient wetness impregnation. Hydrocracking of non-edible vegetable oils at temperature of 400 °C, 20±5 bar for 2 h was performed in the presence of this type of catalyst under hydrogen initial pressure in pressured batch reactor. Non-edible vegetable oils, such as Reutealis trisperma (Blanco) airy shaw (sunan candlenut) and Hevea brasiliensis (rubber seed) were chosen to study the effect of the degree of saturation and lateral chain length on hydrocarbon compounds obtained through hydrocracking. Cerbera manghas oil was also tested for comparison because the composition of fatty acid was different with the other oils The hydrocracking test indicated that liquid product produced has a similar hydrocarbon compounds with petroleum diesel. The most abundant hydrocarbon is pentadecane (n-C15) and heptadecane (n-C17). The high aromatic compounds were found in liquid product produced in hydrocracking of Sunan candlenut oil.

Thorium normalization as a hydrocarbon accumulation indicator for Lower Miocene rocks in Ras Ghara area, Gulf of Suez, Egypt

NASA Astrophysics Data System (ADS)

El-Khadragy, A. A.; Shazly, T. F.; AlAlfy, I. M.; Ramadan, M.; El-Sawy, M. Z.

2018-06-01

An exploration method has been developed using surface and aerial gamma-ray spectral measurements in prospecting petroleum in stratigraphic and structural traps. The Gulf of Suez is an important region for studying hydrocarbon potentiality in Egypt. Thorium normalization technique was applied on the sandstone reservoirs in the region to determine the hydrocarbon potentialities zones using the three spectrometric radioactive gamma ray-logs (eU, eTh and K% logs). This method was applied on the recorded gamma-ray spectrometric logs for Rudeis and Kareem Formations in Ras Ghara oil Field, Gulf of Suez, Egypt. The conventional well logs (gamma-ray, resistivity, neutron, density and sonic logs) were analyzed to determine the net pay zones in the study area. The agreement ratios between the thorium normalization technique and the results of the well log analyses are high, so the application of thorium normalization technique can be used as a guide for hydrocarbon accumulation in the study reservoir rocks.

Hydrocarbon Deposition Attenuates Osteoblast Activity on Titanium

PubMed Central

Hayashi, R.; Ueno, T.; Migita, S.; Tsutsumi, Y.; Doi, H.; Ogawa, T.; Hanawa, T.; Wakabayashi, N.

2014-01-01

Although the reported percentage of bone-implant contact is far lower than 100%, the cause of such low levels of bone formation has rarely been investigated. This study tested the negative biological effect of hydrocarbon deposition onto titanium surfaces, which has been reported to be inevitable. Osteogenic MC3T3-E1 cells were cultured on titanium disks on which the carbon concentration was experimentally regulated to achieve carbon/titanium (C/Ti) ratios of 0.3, 0.7, and 1.0. Initial cellular activities such as cell attachment and cell spreading were concentration-dependently suppressed by the amount of carbon on the titanium surface. The osteoblastic functions of alkaline phosphatase activity and calcium mineralization were also reduced by more than 40% on the C/Ti (1.0) surface. These results indicate that osteoblast activity is influenced by the degree of hydrocarbon contamination on titanium implants and suggest that hydrocarbon decomposition before implant placement may increase the biocompatibility of titanium. PMID:24868012

Geological and geochemical characterization of the Lower Cretaceous Pearsall Formation, Maverick Basin, south Texas: A future shale gas resource?

USGS Publications Warehouse

Hackley, Paul C.

2012-01-01

As part of an assessment of undiscovered hydrocarbon resources in the northern Gulf of Mexico onshore Mesozoic section, the U.S. Geological Survey (USGS) evaluated the Lower Cretaceous Pearsall Formation of the Maverick Basin, south Texas, as a potential shale gas resource. Wireline logs were used to determine the stratigraphic distribution of the Pearsall Formation and to select available core and cuttings samples for analytical investigation. Samples used for this study spanned updip to downdip environments in the Maverick Basin, including several from the current shale gas-producing area of the Pearsall Formation.The term shale does not adequately describe any of the Pearsall samples evaluated for this study, which included argillaceous lime wackestones from more proximal marine depositional environments in Maverick County and argillaceous lime mudstones from the distal Lower Cretaceous shelf edge in western Bee County. Most facies in the Pearsall Formation were deposited in oxygenated environments as evidenced by the presence of biota preserved as shell fragments and the near absence of sediment laminae, which is probably caused by bioturbation. Organic material is poorly preserved and primarily consists of type III kerogen (terrestrial) and type IV kerogen (inert solid bitumen), with a minor contribution from type II kerogen (marine) based on petrographic analysis and pyrolysis. Carbonate dominates the mineralogy followed by clays and quartz. The low abundance and broad size distribution of pyrite are consistent with the presence of oxic conditions during sediment deposition. The Pearsall Formation is in the dry gas window of hydrocarbon generation (mean random vitrinite reflectance values, Ro = 1.2–2.2%) and contains moderate levels of total organic carbon (average 0.86 wt. %), which primarily resides in the inert solid bitumen. Solid bitumen is interpreted to result from in-situ thermal cracking of liquid hydrocarbon generated from original type II kerogen that was prevented from expulsion and migration by low permeability. The temperature of maximum pyrolysis output (Tmax) is a poor predictor of thermal maturity because the pyrolysis (S2) peaks from Rock-Eval analysis are ill defined. Vitrinite reflectance values are consistent with the dry gas window and are the preferred thermal maturity parameter.A Maverick Basin Pearsall shale gas assessment unit was defined using political and geologic boundaries to denote its spatial extent and was evaluated following established USGS hydrocarbon assessment methodology. The assessment estimated a mean undiscovered technically recoverable natural gas resource of 8.8 tcf of gas and 3.4 and 17.8 tcf of gas at the F95 and F5 fractile confidence levels, respectively. Significant engineering challenges will likely need to be met in determining the correct stimulation and completion combination for the successful future development of undiscovered natural gas resources in the Pearsall Formation.

Coal: Its Structure and Some of Its Uses.

ERIC Educational Resources Information Center

Phillips, P. S.

1981-01-01

Describes the formation, chemical structure, and several uses of coal. The history of coal usage, production processes, coal tar products, and production of petroleum and other hydrocarbons from coal are also described. (DS)

Hydrology of coal-lease areas near Durango, Colorado

USGS Publications Warehouse

Brooks, Tom

1985-01-01

The U.S. Bureau of Land Management leases Federal lands and minerals for coal mining near Durango, Colorado. This report addresses the hydrologic suitability of those lands for coal leasing; the report describes the general hydrology of the Durango area and, more specifically, the hydrology of the Stollsteimer Creek study area 32 miles east of the Durango and the Hay Gulch study area, 12 miles southwest of Durango. The most productive aquifers in the Durango study area are Quaternary alluvium and the tertiary Animas Formation. Water wells completed in alluvium typically yield 5 to 20 gallons/min; wells completed is the Animas Formation yield as much as 50 gallons/min. Water quality in these aquifers is variable, but it generally is suitable for domestic use. The coal-bearing Cretaceous Fruitland and Menefee Formations are mined by surface methods at the Chimney Rock Mine in the Stollsteimer Creek study area and by underground methods at the National King Coal Mine in the Hay Gulch study area. Effects of surface mining in the Stollsteimer Creek area are: (1) Dewatering of an alluvial aquifer; and (2) Local degradation of alluvium water quality by spoil-pile effluent. Effects of underground mining in the Hay Gulch area are: (1) Introduction of water with greater dissolved-solids concentrations into the upper Hay Gulch alluvium from mine runoff; (2) Subsidence fracturing which could dewater streams and the alluvial aquifer. (USGS)

Comparison of the petroleum systems of East Venezuela in their tectonostratigraphic context

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stronach, N.J.; Kerr, H.M.; Scotchmer, J.

1996-08-01

The Maturin and Guarico subbasins of East Venezuela record the transition from Cretaceous passive margin to Tertiary foreland basin with local post-orogenic transtensional basins. Petroleum is reservoired in several units ranging from Albian (El Cantil Formation) to Pliocene (Las Piedras Formation) age. Source rocks are principally in the Upper Cretaceous (Querecual Formation), and Miocene (Carapita Formation) in the Maturin subbasin and in the Upper Cretaceous (Tigre Formation) and Oligocene (Roblecito and La Pascua Formations) in the Guarico subbasin. An extensive well database has been used to address the distribution and provenance of hydrocarbons in the context of a tectonostratigraphic modelmore » for the evolution of the East Venezuela basin. Nine major plays have been described, comprising thirteen petroleum systems. The principal factors influencing the components of individual petroleum systems are as follows: (1) structural controls on Upper Cretaceous source rock distribution, relating to block faulting on the proto-Caribbean passive margin; (2) paleoenvironmental controls on source rock development within the Oligocene-Miocene foreland basin; and (3) timing of subsidence and maturation within the Oligocene-Upper Miocene foreland basin and the configuration of the associated fold and thrust belt, influencing long range and local migration routes (4) local development of Pliocene post-orogenic transtensional basins, influencing hydrocarbon generation, migration and remigration north of the Pirital High.« less

Acetoclastic methane formation from Eucalyptus detritus in pristine hydrocarbon-rich river sediments by Methanosarcinales.

PubMed

Beckmann, Sabrina; Manefield, Mike

2014-12-01

Pristine hydrocarbon-rich river sediments in the Greater Blue Mountains World Heritage Area (Australia) release substantial amounts of methane. The present study aimed to unravel for the first time the active methanogens mediating methane formation and exploiting the bacterial diversity potentially involved in the trophic network. Quantitative PCR of 16S rRNA gene and functional genes as well as 454 pyrosequencing were used to address the unknown microbial diversity and abundance. Methane-releasing sediment cores derived from three different river sites of the Tootie River. Highest methane production rates of 10.8 ± 0.5 μg g(-1)(wet weight) day(-1) were detected in 40 cm sediment depth being in congruence with the detection of the highest abundances of the archaeal 16S rRNA gene and the methyl-coenzyme M reductase (mcrA) genes. Stable carbon and hydrogen isotopic signatures of the produced methane indicated an acetoclastic origin. Long-term enrichment cultures amended with either acetate or H2/CO2 revealed acetoclastic methanogenesis as key methane-formation process mediated by members of the order Methanosarcinales. Conditions prevailing in the river sediments might be suitable for hydrocarbon-degrading bacteria observed in the river sediments that were previously unclassified or closely related to the Bacteroidetes/Chlorobi group, the Firmicutes and the Chloroflexi group fuelling acetoclastic methanogensis in pristine river sediments. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Widely different luminescence lifetimes of the [Delta]RRR, [Lambda]SSS and the [Delta]RRS, [Lambda]SSR diastereomers of fac-tris[(8-quinolyl)phenylmethylsily] iridium(III): Exciplex formation with solvents by distinct [sigma]-donor and [pi]-acceptor binding mechanisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Djurovich, P.I.; Cook, W.; Joshi, R.

1994-01-13

Luminescence lifetimes ([tau][sub m]) of the [sigma]-bond-to-ligand charge-transfer (SBLCT) excited states of two diastereomers of fac-tris[(8-quinolyl)phenylmethylsilyl]iridium(III) differ by about a factor of 2 and are strongly solvent dependent. The [tau][sub m] values of the more symmetric [Delta]RRR, [Lambda]SSS diastereomer (A) are generally longer than those of the less symmetric [Delta]RRS, [Lambda]SSR diastereomer (B); [tau][sub m]'s of both diastereomers are substantially shortened relative to their values in aliphatic hydrocarbons by exciplex formation with a variety of weakly coordinating solvents including aromatic hydrocarbons, olefins, ethers, ketones, alcohols, and nitriles. Quenching constants (k[sub q]) due to exciplex formation are found to be muchmore » larger for B than they are for A in the [sigma]-donor solvents (cyclic ethers, ketones, alcohols, and nitriles); however, k[sub q] values of B are slightly smaller than those of A in [pi]-acceptor solvents (aromatic hydrocarbons, olefins). The results suggest that [sigma]-donor solvents form exciplexes by binding at the metal center, whereas [pi]-acceptor solvents bind at a quinolyl radical anion ligand site. A and B may prove useful as luminescent environmental probes which can distinguish between [sigma]-donor and [pi]-acceptor binding sites. 19 refs., 1 fig., 1 tab.« less

Geochemical investigation of the potential for mobilizing non-methane hydrocarbons during carbon dioxide storage in deep coal beds

USGS Publications Warehouse

Kolak, J.J.; Burruss, R.C.

2006-01-01

Coal samples of different rank (lignite to anthracite) were extracted in the laboratory with supercritical CO2 (40 ??C; 10 MPa) to evaluate the potential for mobilizing non-methane hydrocarbons during CO2 storage (sequestration) or enhanced coal bed methane recovery from deep (???1-km depth) coal beds. The total measured alkane concentrations mobilized from the coal samples ranged from 3.0 to 64 g tonne-1 of dry coal. The highest alkane concentration was measured in the lignite sample extract; the lowest was measured in the anthracite sample extract. Substantial concentrations of polycyclic aromatic hydrocarbons (PAHs) were also mobilized from these samples: 3.1 - 91 g tonne-1 of dry coal. The greatest amounts of PAHs were mobilized from the high-volatile bituminous coal samples. The distributions of aliphatic and aromatic hydrocarbons mobilized from the coal samples also varied with rank. In general, these variations mimicked the chemical changes that occur with increasing degrees of coalification and thermal maturation. For example, the amount of PAHs mobilized from coal samples paralleled the general trend of bitumen formation with increasing coal rank. The coal samples yielded hydrocarbons during consecutive extractions with supercritical CO2, although the amount of hydrocarbons mobilized declined with each successive extraction. These results demonstrate that the potential for supercritical CO2 to mobilize non-methane hydrocarbons from coal beds, and the effect of coal rank on this process, are important to consider when evaluating deep coal beds for CO2 storage.

Kinetics and mechanism of soot formation in hydrocarbon combustion

NASA Technical Reports Server (NTRS)

Frenklach, Michael

1990-01-01

The focus of this work was on kinetic modeling. The specific objectives were: detailed modeling of soot formation in premixed flames, elucidation of the effects of fuel structure on the pathway to soot, and the development of a numerical technique for accurate modeling of soot particle coagulation and surface growth. Those tasks were successfully completed and are briefly summarized.

Formation of Prebiotic Molecules in Interstellar and Cometary Ices

NASA Technical Reports Server (NTRS)

Bernstein, Max P.; Sandford, Scott A.; Allamandola, Louis J.; Dworkin, Jason; Gilette, J. Seb; Zare, Richard N.; DeVincenzi, D. (Technical Monitor)

2000-01-01

We report here on our lab studies of ice photochemistry of large organic molecules under cometary conditions. We focus on polycyclic aromatic hydrocarbons (PAHs), their photoproducts, and their similarities to molecules seen in living systems today. We note that these kinds of compounds are seen in meteorites and we propose an explanation for both their formation and their observed deuterium enrichments.

Impact of Propene on Secondary Organic Aerosol Formation from m-Xylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Chen; Na, Kwangsam; Warren, Bethany

2007-10-15

Propene is widely used in smog chamber experiments to increase the hydroxyl radical (OH) level based on the assumption that the formation of secondary organic aerosol (SOA) from parent hydrocarbon is unaffected. A series ofm-xylene/NOx photooxidation experiments were conducted in the presence of propene in the University of California CECERT atmospheric chamber facility. The experimental data are compared with previousm-xylene/NOx photooxidation work performed in the same chamber facility in the absence of propene (Song et al. Environ. Sci. Technol. 2005, 39, 3143-3149). The result shows that, for similar initial conditions, experiments with propene have lower reaction rates of m-xylene thanmore » those without propene, which indicates that propene reduces OH in the system. Furthermore, experiments with propene showed more than 15% reduction in SOA yield compared to experiments in the absence of propene. Additional experiments ofm-xylene/NOx with CO showed similar trends of suppressing OH and SOA formation. These results indicate that SOA from m-xylene/NOx photooxidation is strongly dependent on the OH level present, which provides evidence for the critical role of OH in SOA formation from aromatic hydrocarbons.« less

Exploring Unconventional Hydrocarbons in the Makó Trough, Pannonian basin, Hungary: Results and Challenges

NASA Astrophysics Data System (ADS)

Horvath, Anita; Bada, Gabor; Szafian, Peter; Sztano, Orsolya; Law, Ben; Wallis, Rod

2010-05-01

The latest phase exploration in the Makó Trough, which commenced a few years ago, has focused on the utilization of unconventional hydrocarbons. Accumulations are regarded as "unconventional" when they cannot be produced economically except by means of some sort of stimulation, usually hydraulic fracturing. The model we have developed for the evaluation of the hydrocarbon potential indicates a significant gas accumulation in the area of the Makó Trough. The tally of the distinctive attributes of the hydrocarbon system and the combined analysis of the available geological data led to the conclusion that the Makó Trough represents an area of active basin-centered gas accumulation (BCGA), with very significant perspective reserves. In a BCGA, hydrocarbons do not accumulate conventionally, in structural or stratigraphic traps, but rather in cells. Due to the geological setting of the Makó Trough, the hydrocarbon cell here forms a relatively continuous zone marked by considerable internal lithological and petrophysical variability. The most prolific parts, called sweet spots, possess a reservoir potential higher than the average. The identification of these sweet spots constitutes one of the most important, and quite possibly the most challenging task of the entire exploration project. The hemipelagic Endrőd Formation, which acts as the source rock, contains organic-rich marls in a depth delimited by the 170-230 °C isotherms. These marls constitute the still active hydrocarbon "kitchen" of the BCGA in the Makó Trough. The top and bottom boundaries of the cell essentially coincide with the turbidites of the Szolnok Formation and the top of the pre-Neogene basement, respectively. In light of the fact that pressure, temperature, and maturity tests have produced rather similar results in a number of wells in the area, we have reason to believe that the extension of the Makó Trough's BCGA is of regional dimensions (>1000 km2). The thickness and lateral extension of the potential reservoirs yield a cell volume as great as several hundred km3 - the largest single prospective gas occurrence in Hungary to date. Due to its novelty and complexity, the exploration of this unconventional resource demands the concurrent application of a wider range of geological and geophysical methods. In this presentation, we use selected examples to give an idea of where we stand on the way toward understanding the Makó Trough, particularly in terms of the geometric and structural features of the basin, the depositional (basin-fill) processes, and of the maturation history and accumulation properties of hydrocarbons. The geophysical surveys were purpose-designed to enable the mapping of the deep sedimentary trough and the sediments deposited in it. The data acquired to date suggest that the basin-centered gas accumulation occurred in the Lower Pannonian strata (11-6? Ma). Interpreting the 3D seismic data, the structural features and sedimentology of the basin can be studied in excellent resolution, while the integration of the seismic information with the geological data obtained from the wells allows us to interpret local well information extensively to gain a deeper, three-dimensional understanding of the basin. The sedimentary sequence filling up the Makó Trough displays distinct stratigraphic units separated by unconformities. Mapping the top of the pre-Neogene basement provides valuable insight into the nature of the paleo-geomorphological elements and the sedimentary environment at the onset of rifting. Paleontological information dates the syn-rift sediments of the trough to the Late Miocene (Early Pannonian), suggesting that the most intensive phase of basin evolution here was delayed by a few million years compared to adjacent areas. For the environmental reconstruction of the post-rift sedimentary sequence, we start with the assumption that initially a starved basin existed here, where sedimentation could not keep up with the rate of subsidence (Endrőd Formation). The basin was then almost completely filled by the turbidites of a prograding delta system (Szolnok Formation), followed by the sediments from the pro-delta (Algyő Formation) and the delta plain (Újfalu Formation). During the Plio- and Pleistocene, the area continued to subside at a decreased rate, providing a limited accumulation space filled by a thick sequence of alluvial deposits similar to the paleo-environment of the Tisza River and its tributaries prior to regulation. Our modeling of basin evolution in terms of subsidence, thermal and maturation history based on the results of geochemical, petrophysical, and paleontological investigations reveals that the organic matter accumulated in the trough underwent exceptionally rapid maturation during the last 5 to 7 million years. In fact, source rocks continue to mature at present time, and the hydrocarbons they generate continue to migrate and trap. The rather young age of the Pannonian Basin and its hydrocarbon system makes it quite different from the other examples of basin-centered gas accumulation, such as the classic Rocky Mountains in the U.S., or the Karoo Basin in South Africa, the Beetaloo Basin in Australia, making up the exploration portfolio of Falcon.

Volatile compounds of sulfur in the Fe-C-S system at 5.3 GPa and 1300°C

NASA Astrophysics Data System (ADS)

Zhimulev, E. I.; Sonin, V. M.; Bul'bak, T. A.; Chepurov, A. I.; Tomilenko, A. A.; Pokhilenko, N. P.

2015-05-01

This report presents the results of experimental studies of the fluid phase in the Fe-C-S system at high P and T values (5.3 GPa and 1300°C) conforming to diamond synthesis. The samples for experiments were mounted on air; therefore, the volatile compounds detected after the experiments are characterized by a wide variety and complicated composition involving both inorganic and organic components. Among the inorganic compounds, CO2, H2O, N2, SO2, CS2, and COS were detected. The GC/MS analysis revealed hydrocarbons (paraffins, olefins, and arenes), including high-molecular compounds. The formation of heavy hydrocarbons confirms their thermodynamic stability under high pressure. Oxygenated hydrocarbons (alcohols, aldehydes, ketones, carboxylic acids, and ethers) were also detected.

An evaluation of petrogenic hydrocarbons in northern Gulf of Alaska continental shelf sediments - The role of coastal oil seep inputs

USGS Publications Warehouse

Short, J.W.; Kolak, J.J.; Payne, J.R.; Van Kooten, G. K.

2007-01-01

We compared hydrocarbons in water, suspended particulate matter (SPM), and riparian sediment collected from coastal watersheds along the Yakataga foreland with corresponding hydrocarbons in Gulf of Alaska benthic sediments. This comparison allows an evaluation of hydrocarbon contributions to marine sediments from natural oil seeps, coal and organic matter (e.g., kerogen) associated with eroding siliciclastic rocks. The samples from oil seeps show extensive loss of low-molecular weight n-alkanes (

Urban underground infrastructure mapping and assessment

NASA Astrophysics Data System (ADS)

Huston, Dryver; Xia, Tian; Zhang, Yu; Fan, Taian; Orfeo, Dan; Razinger, Jonathan

2017-04-01

This paper outlines and discusses a few associated details of a smart cities approach to the mapping and condition assessment of urban underground infrastructure. Underground utilities are critical infrastructure for all modern cities. They carry drinking water, storm water, sewage, natural gas, electric power, telecommunications, steam, etc. In most cities, the underground infrastructure reflects the growth and history of the city. Many components are aging, in unknown locations with congested configurations, and in unknown condition. The technique uses sensing and information technology to determine the state of infrastructure and provide it in an appropriate, timely and secure format for managers, planners and users. The sensors include ground penetrating radar and buried sensors for persistent sensing of localized conditions. Signal processing and pattern recognition techniques convert the data in information-laden databases for use in analytics, graphical presentations, metering and planning. The presented data are from construction of the St. Paul St. CCTA Bus Station Project in Burlington, VT; utility replacement sites in Winooski, VT; and laboratory tests of smart phone position registration and magnetic signaling. The soil conditions encountered are favorable for GPR sensing and make it possible to locate buried pipes and soil layers. The present state of the art is that the data collection and processing procedures are manual and somewhat tedious, but that solutions for automating these procedures appear to be viable. Magnetic signaling with moving permanent magnets has the potential for sending lowfrequency telemetry signals through soils that are largely impenetrable by other electromagnetic waves.

Novel insights into freshwater hydrocarbon-rich sediments using metatranscriptomics: Opening the black box.

PubMed

Reid, Thomas; Chaganti, Subba Rao; Droppo, Ian G; Weisener, Christopher G

2018-06-01

Baseline biogeochemical surveys of natural environments is an often overlooked field of environmental studies. Too often research begins once contamination has occurred, with a knowledge gap as to how the affected area behaved prior to outside (often anthropogenic) influences. These baseline characterizations can provide insight into proposed bioremediation strategies crucial in cleaning up chemical spill sites or heavily mined regions. Hence, this study was conducted to survey the in-situ microbial activity within freshwater hydrocarbon-rich environments cutting through the McMurray formation - the geologic strata constituting the oil sands. We are the first to report in-situ functional variations among these freshwater microbial ecosystems using metatranscriptomics, providing insight into the in-situ gene expression within these naturally hydrocarbon-rich sites. Key genes involved in energy metabolism (nitrogen, sulfur and methane) and hydrocarbon degradation, including transcripts relating to the observed expression of methane oxidation are reported. This information provides better linkages between hydrocarbon impacted environments, closing knowledge gaps for optimizing not only oil sands mine reclamation but also enhancing microbial reclamation strategies in various freshwater environments. These finding can also be applied to existing contaminated environments, in need of efficient reclamation efforts. Copyright © 2018 Elsevier Ltd. All rights reserved.

Volatile aromatic hydrocarbons and dicarboxylic acid concentrations in air at an urban site in the Southwestern US

NASA Astrophysics Data System (ADS)

Tran, Ngoc K.; Steinberg, Spencer M.; Johnson, Brian J.

Concentrations of benzene, toluene, ethylbenzene, o-xylene, and m- and p-xylene were measured at an urban sampling site in Las Vegas, NV by sorbent sampling followed by thermal desorption and determination by GC-PID. Simultaneously, measurements of oxalic, malonic, succinic, and adipic acids were made at the same site by collection on quartz filters, extraction, esterification, and determination by GC-FID. For the period from April 7, 1997 to June 11, 1997, 201 sets of hydrocarbon measurements and 99 sets of acid measurements were made. Additional measurements of dicarboxylic acids were made on samples that represented potential direct sources, e.g. green plants and road dust. Correlations between the hydrocarbon and CO concentrations (measured by the Clark County Health District at a nearby site) were highly significant and a strong negative correlation of hydrocarbon concentration with ozone concentration (also from the county site) was observed under quiescent atmospheric conditions. In general, dicarboxylic acid concentrations were well correlated with one another (with the exception of adipic acid) but not well correlated with hydrocarbon, CO, and ozone concentrations. Multiple sources and complex formation processes are indicated for the dicarboxylic acids.

Occurrence of high gravity oil in an Oligocene Vicksburg age sandstone in Jim Hogg County, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, L.W.; Hilton, N.

1980-01-01

On October 1, 1979 the Guardian Oil Co. E-1 Mestena oil and gas well was completed in an Oligocene, Vicksburg sandstone. The initial potential was 245 BOPD of 75 API gravity oil. A hydrocarbon analysis of a sample obtained from the E-1 well revealed an oil composed primarily of propane and butane with a significant portion of pentane to heptane range material which accounts for the exceptionally high gravity of the liquid hydrocarbons. This analysis further showed that the E-1 well is producing almost no methane, ethane, or other hydrocarbons of greater molecular weight than nonane. Several faults, adjacent tomore » the well, could have provided a path of migration for the hydrocarbons. A detailed analysis of the butane to heptane fluid produced by the E-1 well indicated the fluid contained a large amount of compounds characteristic of an immature crude. Coal fragments present in the cutting from a nearby well and the regional geology of the Vicksburg Formation suggest that one possible source for the hydrocarbons of the E-1 well could have been lipid rich Cannel-type coal.« less

Amino acids and hydrocarbons approximately 3,800-Myr old in the Isua rocks, southwestern Greenland

NASA Technical Reports Server (NTRS)

Nagy, B.; Engel, M. H.; Zumberge, J. E.; Ogino, H.; Chang, S. Y.

1981-01-01

Results of an analysis of amino acids and hydrocarbons found in the Isua banded iron formation, which contains the oldest known rocks on earth, are discussed. Similarities are pointed out between the relative amino acid abundances of the Isua rocks and those of lichens found on their surfaces, and a lack of substantial racemization indicated by the low D/L ratios in the 3800-million year old rock samples is noted. Experimental results showing the possibility of amino acid diffusion from lichens into the rocks are presented. Comparisons of the Isua rock amino acid D/L ratios with those reported for samples from other regions indicates that none of the Isua amino acids are older than a few tens of thousands to a few hundred thousand years. Analyses of the saturated hydrocarbons of the Isua samples reveals no odd carbon number preference, which may indicate antiquity, however laboratory experiments have shown that amino acids and aromatic and saturated aliphatic hydrocarbons could not have survived the metamorphic history of the Isua rocks. The evidence presented thus suggests that the amino acids and hydrocarbons found are not of the age of the sediments.

Radiocarbon-depleted CO2 evidence for fuel biodegradation at the Naval Air Station North Island (USA) fuel farm site.

PubMed

Boyd, Thomas J; Pound, Michael J; Lohr, Daniel; Coffin, Richard B

2013-05-01

Dissolved CO(2) radiocarbon and stable carbon isotope ratios were measured in groundwater from a fuel contaminated site at the North Island Naval Air Station in San Diego, CA (USA). A background groundwater sampling well and 16 wells in the underground fuel contamination zone were evaluated. For each sample, a two end-member isotopic mixing model was used to determine the fraction of CO(2) derived from fossil fuel. The CO(2) fraction from fossil sources ranged from 8 to 93% at the fuel contaminated site, while stable carbon isotope values ranged from -14 to +5‰VPDB. Wells associated with highest historical and contemporary fuel contamination showed the highest fraction of CO(2) derived from petroleum (fossil) sources. Stable carbon isotope ratios indicated sub-regions on-site with recycled CO(2) (δ(13)CO(2) as high as +5‰VPDB) - most likely resulting from methanogenesis. Ancillary measurements (pH and cations) were used to determine that no fossil CaCO(3), for instance limestone, biased the analytical conclusions. Radiocarbon analysis is verified as a viable and definitive technique for confirming fossil hydrocarbon conversion to CO(2) (complete oxidation) at hydrocarbon-contaminated groundwater sites. The technique should also be very useful for assessing the efficacy of engineered remediation efforts and by using CO(2) production rates, contaminant mass conversion over time and per unit volume.

Numerical investigation and Uncertainty Quantification of the Impact of the geological and geomechanical properties on the seismo-acoustic responses of underground chemical explosions

NASA Astrophysics Data System (ADS)

Ezzedine, S. M.; Pitarka, A.; Vorobiev, O.; Glenn, L.; Antoun, T.

2017-12-01

We have performed three-dimensional high resolution simulations of underground chemical explosions conducted recently in jointed rock outcrop as part of the Source Physics Experiments (SPE) being conducted at the Nevada National Security Site (NNSS). The main goal of the current study is to investigate the effects of the structural and geomechanical properties on the spall phenomena due to underground chemical explosions and its subsequent effect on the seismo-acoustic signature at far distances. Two parametric studies have been undertaken to assess the impact of different 1) conceptual geological models including a single layer and two layers model, with and without joints and with and without varying geomechanical properties, and 2) depth of bursts of the chemical explosions and explosion yields. Through these investigations we have explored not only the near-field response of the chemical explosions but also the far-field responses of the seismic and the acoustic signatures. The near-field simulations were conducted using the Eulerian and Lagrangian codes, GEODYN and GEODYN -L, respectively, while the far-field seismic simulations were conducted using the elastic wave propagation code, WPP, and the acoustic response using the Kirchhoff-Helmholtz-Rayleigh time-dependent approximation code, KHR. Though a series of simulations we have recorded the velocity field histories a) at the ground surface on an acoustic-source-patch for the acoustic simulations, and 2) on a seismic-source-box for the seismic simulations. We first analyzed the SPE3 experimental data and simulated results, then simulated SPE4-prime, SPE5, and SPE6 to anticipate their seismo-acoustic responses given conditions of uncertainties. SPE experiments were conducted in a granitic formation; we have extended the parametric study to include other geological settings such dolomite and alluvial formations. These parametric studies enabled us 1) investigating the geotechnical and geophysical key parameters that impact the seismo-acoustic responses of underground chemical explosions and 2) deciphering and ranking through a global sensitivity analysis the most important key parameters to be characterized on site to minimize uncertainties in prediction and discrimination.

Aircraft engine pollution reduction

NASA Technical Reports Server (NTRS)

Rudey, R. A.

1972-01-01

The effect of engine operation on the types and levels of the major aircraft engine pollutants is described and the major factors governing the formation of these pollutants during the burning of hydrocarbon fuel are discussed. Methods which are being explored to reduce these pollutants are discussed and their application to several experimental research programs are pointed out. Results showing significant reductions in the levels of carbon monoxide, unburned hydrocarbons, and oxides of nitrogen obtained from experimental combustion research programs are presented and discussed to point out potential application to aircraft engines.

Homogeneous reactions of hydrocarbons, silane, and chlorosilanes in radiofrequency plasmas at low pressures

NASA Technical Reports Server (NTRS)

Avni, R.; Carmi, U.; Inspektor, A.; Rosenthal, I.

1984-01-01

The ion-molecule and radical-molecule mechanisms are responsible for the dissociation of hydrocarbon, silane, and chlorosilane monomers and the formation of polymerized species, respectively, in an RF plasma discharge. In a plasma containing a mixture of monomer and argon the rate-determining step for both dissociation and polymerization is governed by an ion-molecule type of interaction. Adding hydrogen or ammonia to the monomer-argon mixture transforms the rate-determining step from an ion-molecule interaction to a radical-molecule interaction for both monomer dissociation and polymerization.

Role of Underground Erosion of Ice Wedges in Drainage System Formation

NASA Astrophysics Data System (ADS)

Fortier, D.; Shur, Y.; Allard, M.

2006-12-01

Natural rapid development of a new drainage system was studied on Bylot Island, Nunavut, Canada (73° 10' N, 80° 05' W). Formation of sinkholes eroded in ice wedges evolved in underground tunnels cut in ice- rich permafrost (average water content of 130%). The tunnel scouring process occurred mainly during snowmelt runoff and was manifestly a function of the intensity of the water flow entering the permafrost. When surface water flowed into the ground, the active layer was still frozen and the temperature of the permafrost at a depth of 3 m was below -15°C. Forced convection with a high convective heat transfer coefficient provided high rate of tunnels enlargement. The erosion rate was much higher in the beginning of runoff, when its velocity and discharge were high but water and soil were colder, than later in the summer, when water and soil temperature was much warmer but water discharge and velocity much lower. Widening of tunnels was followed by creep subsidence and collapse of their roofs and development of gullies. The drainage has generally developed along the elevation gradient. Some deviation from it was caused by temporal obstruction to water flow from collapsed blocks of soil. In such cases water found the way through connecting ice wedges. Retrogressive erosion escarpments exposed to flowing water retreated at a maximum rate of 1 to 5 meters per day for a total of 15 to 50 m during the summer. Escarpment exposed to atmospheric heat and solar radiation receded at a rate of 0.6 and 10 m per summer with a mean of 4 meters during the first year of exposition. Such slopes were nearly stabilized after 4 years with retreat rate of only a few centimeters per year in 2002. In four years, the underground tunnel network evolved into a continuous system of gullies over 750 m long and covering an area of about 20,000 m2. The main factors affecting rapid development of the new drainage system are the rate and volume of runoff, the presence of ice wedges, their dimension and orientation, and the ice content of the sediments. Ice wedge volume growth over the years increases their susceptibility to underground thermo-erosion. Climate warming scenarios predict increase in summer and winter precipitation in the Arctic and, as a result, underground thermo-erosion is likely to be more frequent and remodeling of the drainage system more aggressive. More work remains to be done to understand the changes that have occurred in the watershed to trigger such significant readjustments to the drainage system.

30 CFR 280.24 - What reports must I file?

Code of Federal Regulations, 2010 CFR

2010-07-01

... digital navigation data in a format specified by the RD, showing the areas and blocks in which any G&G...) A summary of any: (i) Hard mineral, hydrocarbon, or sulphur occurrences encountered; (ii...

The Model of Educational Reconstruction--A Powerful Strategy to Teach for Conceptual Development in Physical Geography: The Case of Water Springs

ERIC Educational Resources Information Center

Reinfried, Sibylle; Aeschbacher, Urs; Kienzler, Peter M.; Tempelmann, Sebastian

2015-01-01

Springs are an important hydrological concept because springs form an interface between underground and surface sub-systems of the hydrological cycle. Furthermore, springs are important suppliers of drinking water but are at risk today due to numerous anthropogenic interferences. The general knowledge of springs and their formation is usually…

Features of natural environment and occurrence of groundwater in cold artesian basins in permafrost areas, China

NASA Astrophysics Data System (ADS)

Feng-Tong, Lin

1988-08-01

This article is a report on features of the natural environment of the Huola River artesian water basin in Guilan District, Mohe County, in the Xin-an Region and the interrelationship of various factors of underground water under glacial conditions. Formations, recharge, distribution, drainage, and transfer, as compared with nonperennial frozen areas, are described.

Long term changes in the concentration of radium in discharge waters of coal mines and Upper Silesian rivers.

PubMed

Chałupnik, Stanisław; Wysocka, Małgorzata; Janson, Ewa; Chmielewska, Izabela; Wiesner, Marta

2017-05-01

According to the latest guidelines of the International Atomic Energy Agency (IAEA, 2016), coal mining is one of the most important contributors to occupational exposure. Coal mining contributes about 45% of the total annual collective dose obtained by workers due to the exposure at places of working. One of the sources of exposure in mining are formation brines with elevated concentrations of natural radionuclides, the most common are radium 226 Ra and 228 Ra. Radium isotopes often occur in formation waters in underground collieries in the Upper Silesian region (USCB) in Poland. Significant amounts of radium remain underground in the form of radioactive deposits created as a result of spontaneous deposition or water treatment. This phenomenon leads to the increase of radiation hazard for miners. The remaining activities of 226 Ra and 228 Ra are released into the rivers with mine effluents, causing the contamination of bottom sediments and river banks. The results of radioactivity monitoring of effluents and river waters are presented here to illustrate a trend of long-term changes in environmental contamination, caused by mining industry in the Upper Silesian Region. Copyright © 2017 Elsevier Ltd. All rights reserved.

Revealing Lattice Expansion of Small-Pore Zeolite Catalysts during the Methanol-to-Olefins Process Using Combined Operando X-ray Diffraction and UV-vis Spectroscopy.

PubMed

Goetze, Joris; Yarulina, Irina; Gascon, Jorge; Kapteijn, Freek; Weckhuysen, Bert M

2018-03-02

In small-pore zeolite catalysts, where the size of the pores is limited by eight-ring windows, aromatic hydrocarbon pool molecules that are formed inside the zeolite during the Methanol-to-Olefins (MTO) process cannot exit the pores and are retained inside the catalyst. Hydrocarbon species whose size is comparable to the size of the zeolite cage can cause the zeolite lattice to expand during the MTO process. In this work, the formation of retained hydrocarbon pool species during MTO at a reaction temperature of 400 °C was followed using operando UV-vis spectroscopy. During the same experiment, using operando X-ray Diffraction (XRD), the expansion of the zeolite framework was assessed, and the activity of the catalyst was measured using online gas chromatography (GC). Three different small-pore zeolite frameworks, i.e., CHA, DDR, and LEV, were compared. It was shown using operando XRD that the formation of retained aromatic species causes the zeolite lattice of all three frameworks to expand. Because of the differences in the zeolite framework dimensions, the nature of the retained hydrocarbons as measured by operando UV-vis spectroscopy is different for each of the three zeolite frameworks. Consequently, the magnitude and direction of the zeolite lattice expansion as measured by operando XRD also depends on the specific combination of the hydrocarbon species and the zeolite framework. The catalyst with the CHA framework, i.e., H-SSZ-13, showed the biggest expansion: 0.9% in the direction along the c -axis of the zeolite lattice. For all three zeolite frameworks, based on the combination of operando XRD and operando UV-vis spectroscopy, the hydrocarbon species that are likely to cause the expansion of the zeolite cages are presented; methylated naphthalene and pyrene in CHA, 1-methylnaphthalene and phenalene in DDR, and methylated benzene and naphthalene in LEV. Filling of the zeolite cages and, as a consequence, the zeolite lattice expansion causes the deactivation of these small-pore zeolite catalysts during the MTO process.

Revealing Lattice Expansion of Small-Pore Zeolite Catalysts during the Methanol-to-Olefins Process Using Combined Operando X-ray Diffraction and UV–vis Spectroscopy

PubMed Central

2018-01-01

In small-pore zeolite catalysts, where the size of the pores is limited by eight-ring windows, aromatic hydrocarbon pool molecules that are formed inside the zeolite during the Methanol-to-Olefins (MTO) process cannot exit the pores and are retained inside the catalyst. Hydrocarbon species whose size is comparable to the size of the zeolite cage can cause the zeolite lattice to expand during the MTO process. In this work, the formation of retained hydrocarbon pool species during MTO at a reaction temperature of 400 °C was followed using operando UV–vis spectroscopy. During the same experiment, using operando X-ray Diffraction (XRD), the expansion of the zeolite framework was assessed, and the activity of the catalyst was measured using online gas chromatography (GC). Three different small-pore zeolite frameworks, i.e., CHA, DDR, and LEV, were compared. It was shown using operando XRD that the formation of retained aromatic species causes the zeolite lattice of all three frameworks to expand. Because of the differences in the zeolite framework dimensions, the nature of the retained hydrocarbons as measured by operando UV–vis spectroscopy is different for each of the three zeolite frameworks. Consequently, the magnitude and direction of the zeolite lattice expansion as measured by operando XRD also depends on the specific combination of the hydrocarbon species and the zeolite framework. The catalyst with the CHA framework, i.e., H-SSZ-13, showed the biggest expansion: 0.9% in the direction along the c-axis of the zeolite lattice. For all three zeolite frameworks, based on the combination of operando XRD and operando UV–vis spectroscopy, the hydrocarbon species that are likely to cause the expansion of the zeolite cages are presented; methylated naphthalene and pyrene in CHA, 1-methylnaphthalene and phenalene in DDR, and methylated benzene and naphthalene in LEV. Filling of the zeolite cages and, as a consequence, the zeolite lattice expansion causes the deactivation of these small-pore zeolite catalysts during the MTO process. PMID:29527401

Influence of crude oil cracking on distribution of hydrocarbons in the Earth's interior (experimental data)

NASA Astrophysics Data System (ADS)

Balitsky, V. S.; Balitskaya, L. V.; Penteley, S. V.; Novikova, M. A.

2012-02-01

The compositions and phase conditions of water-hydrocarbon fluids in synthetic quartz inclusions were studied by the methods of microthermometry, local IR spectroscopy, and gas-liquid chromatography. Synthetic quartz was grown in near-neutral fluoride, low-alkali bicarbonate, and alkali carbonate solutions with crude oil and its major fractions. The crystals with fluid inclusions were grown under thermal gradient conditions at relatively low temperatures (240-280°C) and pressures (6-45 MPa). After the study, the inclusions of grown crystals were subject to thermal processing in autoclaves at 350-380°C and 80-125 MPa. As a result, the initial water-hydrocarbon inclusions underwent significant changes. Hydrocarbon gases, largely methane and residual solid bitumens, appeared in their composition; the gasoline-kerosene fraction content increased substantially in liquid hydrocarbons (HCs). These changes are caused, first of all, by crude oil cracking, which is manifested already at 330°C and attains its maximum activity at 350-500°C (pressure of saturated vapor and higher). In natural conditions with increase in depths and, thus, the thermobaric parameters, this process is inevitable. According to the obtained experimental data, this very phenomenon and the existence of real thermal and baric gradients in the Earth's interior provide for the formation of vertical zoning in the distribution of hydrocarbon deposits of different types.

Enhanced bioavailability of polyaromatic hydrocarbons in the form of mucin complexes.

PubMed

Drug, Eyal; Landesman-Milo, Dalit; Belgorodsky, Bogdan; Ermakov, Natalia; Frenkel-Pinter, Moran; Fadeev, Ludmila; Peer, Dan; Gozin, Michael

2011-03-21

Increasing exposure of biological systems to large amounts of polycyclic aromatic hydrocarbons is of great public concern. Organisms have an array of biological defense mechanisms, and it is believed that mucosal gel (which covers the respiratory system, the gastrointestinal tract, etc.) provides an effective chemical shield against a range of toxic materials. However, in this work, we demonstrate, for the first time, that, upon complexation of polyaromatic hydrocarbons with mucins, enhanced bioavailability and, therefore, toxicity are obtained. This work was aimed to demonstrate how complexation of various highly hydrophobic polycyclic aromatic hydrocarbons with representative mucin glycoprotein could lead to the formation of previously undescribed materials, which exhibit increased toxicity versus pristine polycyclic aromatic hydrocarbons. In the present work, we show that a representative mucin glycoprotein, bovine submaxillary mucin, has impressive and unprecedented capabilities of binding and solubilizing water-insoluble materials in physiological solution. The complexes formed between the mucin and a series of polycyclic aromatic hydrocarbons were comprehensively characterized, and their toxicity was evaluated by both in vivo and in vitro assays. In addition, the bioavailability and membrane-penetration capabilities were tested using an internalization assay. Our results provide, for the first time, evidence of an unknown route by which hydrophobic materials may achieve higher bioavailability, penetrating some of the biological defense systems, in the form of water-soluble complexes with mucosal proteins.

Parallel heater system for subsurface formations

DOEpatents

Harris, Christopher Kelvin [Houston, TX; Karanikas, John Michael [Houston, TX; Nguyen, Scott Vinh [Houston, TX

2011-10-25

A heating system for a subsurface formation is disclosed. The system includes a plurality of substantially horizontally oriented or inclined heater sections located in a hydrocarbon containing layer in the formation. At least a portion of two of the heater sections are substantially parallel to each other. The ends of at least two of the heater sections in the layer are electrically coupled to a substantially horizontal, or inclined, electrical conductor oriented substantially perpendicular to the ends of the at least two heater sections.

[Energy policy rather than climate policy].

PubMed

Kroonenberg, Salomon B

2009-01-01

Energy policy and climate policy are two different issues and should not be treated as if they were the same. Whether the climate gets warmer or colder, saving energy and developing sustainable forms of energy production remain of paramount importance because fossil hydrocarbons are likely to be exhausted soon. But climate policy is a fallacy: it is human arrogance to think we can control the climate by reducing emissions and by storing CO2 underground. In spite of rising CO2 levels, the climate has cooled down slightly over the past decade. Since the International Panel on Climate Change (IPCC) did not predict this, it is questionable whether they can reliably predict warming. Other factors such as solar activity are probably more important for climate than greenhouse gases. The danger of coupling energy policy to climate policy is evident: if the climate cools down, people will lose belief in the greenhouse effect and therefore also lose interest in saving energy.

Evaluation of 2D resistivity imaging technique for delineating subsurface seepage of hydrocarbon-contaminated water southeast of Karbala city, Iraq.

PubMed

Al-Menshed, Firas H; Thabit, Jassim M

2017-03-01

2D imaging technique was applied in (8) transects near a pit of contaminated water near contaminated well southeast of Karbala city, Iraq. Each transect was 30 m long with 1 m electrode spacing. Data acquisition was fulfilled by using Wenner electrode array. The resistivity of water-contaminated zone is found less than 3Ω.m and the top dry zone recorded relatively high resistivity (more than 170Ω.m). It is found that the greatest amount of seepage was found moving towards northeast direction coincided with groundwater movement direction, whereas there was no movement towards northwest and southeast directions and restricted on the closest areas to the pit location. The outcomes suggested that the 2D imaging technique is a successful and powerful tool in separating contaminated zone from clear one and in detecting underground seepage depth and moving direction.

Changes in Magnetic Mineralogy Through a Depth Sequence of Hydrocarbon Contaminated Sediments

NASA Astrophysics Data System (ADS)

Ameen, N. N.; Klüglein, N.; Appel, E.; Petrovsky, E.; Kappler, A.

2013-12-01

Sediments, soils and groundwater can act as a natural storage for many types of pollution. This study aims to investigate ferro(i)magnetic phase formation and transformation in the presence of organic contaminants (hydrocarbons) and its relation to bacterial activity, in particular in the zone of fluctuating water levels. The work extends previous studies conducted at the same site. The study area is a former military air base at Hradčany, Czech Republic (50°37'22.71"N, 14°45'2.24"E). Due to leaks in petroleum storage tanks and jet fuelling stations over years of active use the site was heavily contaminated with petroleum hydrocarbons, until the base was closed in 1991. This site is one of the most important sources of high quality groundwater in the Czech Republic. During remediation processes the groundwater level in the sediments fluctuated, driving the hydrocarbon contaminants to lower depth levels along with the groundwater and leading to magnetite formation (Rijal et al., Environ.Pollut., 158, 1756-1762, 2010). In our study we drilled triplicate cores at three locations which were studied earlier. Magnetic susceptibility (MS) profiles combined with other magnetic properties were analyzed to obtain the ferro(i)magnetic concentration distributions along the depth sections. Additionally the sediment properties, hydrocarbon content and bacterial activity were studied. The triplicate cores were used to statistically discriminate outliers and to recognize significant magnetic signatures with depth. The results show that the highest concentration of ferrimagnetic phases (interpreted as newly formed magnetite) exists at the probable top of the groundwater fluctuation (GWF) zone. For example at one of the sites this zone is found between 1.4-1.9 m depth (groundwater table at ~2.3 m depth). High S-ratio and the correlation of ARM with MS values confirm the contribution of magnetite for the ferro(i)magnetic enhancement in the GWF zone. In the previous studies the MS signals revealed small-scale isolated features, but with the use of triplicate cores significant trends of MS could be identified, showing an increase from the lowermost position of the groundwater table upward. Bacterial activity is likely responsible for magnetite formation in this depth range as indicated by most probable number (MPN) results of iron-reducing bacteria.

Rapid Formation of Microbe-Oil Aggregates and Changes in Community Composition in Coastal Surface Water Following Exposure to Oil and the Dispersant Corexit.

PubMed

Doyle, Shawn M; Whitaker, Emily A; De Pascuale, Veronica; Wade, Terry L; Knap, Anthony H; Santschi, Peter H; Quigg, Antonietta; Sylvan, Jason B

2018-01-01

During the Deepwater Horizon (DWH) oil spill, massive quantities of oil were deposited on the seafloor via a large-scale marine oil-snow sedimentation and flocculent accumulation (MOSSFA) event. The role of chemical dispersants (e.g., Corexit) applied during the DWH oil spill clean-up in helping or hindering the formation of this MOSSFA event are not well-understood. Here, we present the first experiment related to the DWH oil spill to specifically investigate the relationship between microbial community structure, oil and Corexit®, and marine oil-snow in coastal surface waters. We observed the formation of micron-scale aggregates of microbial cells around droplets of oil and dispersant and found that their rate of formation was directly related to the concentration of oil within the water column. These micro-aggregates are potentially important precursors to the formation of larger marine oil-snow particles. Therefore, our observation that Corexit® significantly enhanced their formation suggests dispersant application may play a role in the development of MOSSFA events. We also observed that microbial communities in marine surface waters respond to oil and oil plus Corexit® differently and much more rapidly than previously measured, with major shifts in community composition occurring within only a few hours of experiment initiation. In the oil-amended treatments without Corexit®, this manifested as an increase in community diversity due to the outgrowth of several putative aliphatic- and aromatic-hydrocarbon degrading genera, including phytoplankton-associated taxa. In contrast, microbial community diversity was reduced in mesocosms containing chemically dispersed oil. Importantly, different consortia of hydrocarbon degrading bacteria responded to oil and chemically dispersed oil, indicating that functional redundancy in the pre-spill community likely results in hydrocarbon consumption in both undispersed and dispersed oils, but by different bacterial taxa. Taken together, these data improve our understanding of how dispersants influence the degradation and transport of oil in marine surface waters following an oil spill and provide valuable insight into the early response of complex microbial communities to oil exposure.

Inhibition of aryl hydrocarbon receptor transactivation and DNA adduct formation by CYP1 isoform-selective metabolic deactivation of benzo[a]pyrene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Endo, Kaori; Uno, Shigeyuki; Seki, Taiichiro

Benzo[a]pyrene (BaP), a polyaromatic hydrocarbon produced by the combustion of cigarettes and coke ovens, is a known procarcinogen. BaP activates the aryl hydrocarbon receptor (AhR) and induces the expression of a battery of genes, including CYP1A1, which metabolize BaP to toxic compounds. The possible role of CYP1 enzymes in mediating BaP detoxification or metabolic activation remains to be elucidated. In this study, we assessed the effects of CYP1 enzymes (CYP1A1, CYP1A2 and CYP1B1) on BaP-induced AhR transactivation and DNA adduct formation in HEK293 cells and HepG2 cells. Transfection of CYP1A1 and CYP1B1, but not CYP1A2, suppressed BaP-induced activation of AhR.more » Expression of CYP1A1 and CYP1A2, but not CYP1B1, inhibited DNA adduct formation in BaP-treated HepG2 cells. These results indicate that CYP1A1 and CYP1B1 play a role in deactivation of BaP on AhR and that CYP1A1 and CYP1A2 are involved in BaP detoxification by suppressing DNA adduct formation. BaP treatment did not induce DNA adduct formation in HEK293 cells, even after transfection of CYP1 enzymes, suggesting that expression of CYP1 enzymes is not sufficient for DNA adduct formation. Lower expression of epoxide hydrolase and higher expression of glutathione S-transferase P1 (GSTP1) and GSTM1/M2 were observed in HEK293 cells compared with HepG2 cells. Dynamic expression of CYP1A1, CYP1A2 and CYP1B1 along with expression of other enzymes such as epoxide hydrolase and phase II enzymes may determine the detoxification or metabolic activation of BaP.« less

Rapid Formation of Microbe-Oil Aggregates and Changes in Community Composition in Coastal Surface Water Following Exposure to Oil and the Dispersant Corexit

PubMed Central

Doyle, Shawn M.; Whitaker, Emily A.; De Pascuale, Veronica; Wade, Terry L.; Knap, Anthony H.; Santschi, Peter H.; Quigg, Antonietta; Sylvan, Jason B.

2018-01-01

During the Deepwater Horizon (DWH) oil spill, massive quantities of oil were deposited on the seafloor via a large-scale marine oil-snow sedimentation and flocculent accumulation (MOSSFA) event. The role of chemical dispersants (e.g., Corexit) applied during the DWH oil spill clean-up in helping or hindering the formation of this MOSSFA event are not well-understood. Here, we present the first experiment related to the DWH oil spill to specifically investigate the relationship between microbial community structure, oil and Corexit®, and marine oil-snow in coastal surface waters. We observed the formation of micron-scale aggregates of microbial cells around droplets of oil and dispersant and found that their rate of formation was directly related to the concentration of oil within the water column. These micro-aggregates are potentially important precursors to the formation of larger marine oil-snow particles. Therefore, our observation that Corexit® significantly enhanced their formation suggests dispersant application may play a role in the development of MOSSFA events. We also observed that microbial communities in marine surface waters respond to oil and oil plus Corexit® differently and much more rapidly than previously measured, with major shifts in community composition occurring within only a few hours of experiment initiation. In the oil-amended treatments without Corexit®, this manifested as an increase in community diversity due to the outgrowth of several putative aliphatic- and aromatic-hydrocarbon degrading genera, including phytoplankton-associated taxa. In contrast, microbial community diversity was reduced in mesocosms containing chemically dispersed oil. Importantly, different consortia of hydrocarbon degrading bacteria responded to oil and chemically dispersed oil, indicating that functional redundancy in the pre-spill community likely results in hydrocarbon consumption in both undispersed and dispersed oils, but by different bacterial taxa. Taken together, these data improve our understanding of how dispersants influence the degradation and transport of oil in marine surface waters following an oil spill and provide valuable insight into the early response of complex microbial communities to oil exposure. PMID:29696005

An efficient approach to imaging underground hydraulic networks

NASA Astrophysics Data System (ADS)

Kumar, Mohi

2012-07-01

To better locate natural resources, treat pollution, and monitor underground networks associated with geothermal plants, nuclear waste repositories, and carbon dioxide sequestration sites, scientists need to be able to accurately characterize and image fluid seepage pathways below ground. With these images, scientists can gain knowledge of soil moisture content, the porosity of geologic formations, concentrations and locations of dissolved pollutants, and the locations of oil fields or buried liquid contaminants. Creating images of the unknown hydraulic environments underfoot is a difficult task that has typically relied on broad extrapolations from characteristics and tests of rock units penetrated by sparsely positioned boreholes. Such methods, however, cannot identify small-scale features and are very expensive to reproduce over a broad area. Further, the techniques through which information is extrapolated rely on clunky and mathematically complex statistical approaches requiring large amounts of computational power.