Hearing in the Juvenile Green Sea Turtle (Chelonia mydas): A Comparison of Underwater and Aerial Hearing Using Auditory Evoked Potentials.

PubMed

Piniak, Wendy E D; Mann, David A; Harms, Craig A; Jones, T Todd; Eckert, Scott A

2016-01-01

Sea turtles spend much of their life in aquatic environments, but critical portions of their life cycle, such as nesting and hatching, occur in terrestrial environments, suggesting that it may be important for them to detect sounds in both air and water. In this study we compared underwater and aerial hearing sensitivities in five juvenile green sea turtles (Chelonia mydas) by measuring auditory evoked potential responses to tone pip stimuli. Green sea turtles detected acoustic stimuli in both media, responding to underwater stimuli between 50 and 1600 Hz and aerial stimuli between 50 and 800 Hz, with maximum sensitivity between 200 and 400 Hz underwater and 300 and 400 Hz in air. When underwater and aerial hearing sensitivities were compared in terms of pressure, green sea turtle aerial sound pressure thresholds were lower than underwater thresholds, however they detected a wider range of frequencies underwater. When thresholds were compared in terms of sound intensity, green sea turtle sound intensity level thresholds were 2-39 dB lower underwater particularly at frequencies below 400 Hz. Acoustic stimuli may provide important environmental cues for sea turtles. Further research is needed to determine how sea turtles behaviorally and physiologically respond to sounds in their environment.

Induction of settlement in mussel (Perna canaliculus) larvae by vessel noise.

PubMed

Wilkens, S L; Stanley, J A; Jeffs, A G

2012-01-01

Underwater sound plays an important role in the settlement behaviour of many coastal organisms. Large steel-hulled vessels are known to be a major source of underwater sound in the marine environment. The possibility that underwater sound from vessels may promote biofouling of hulls through triggering natural larval settlement cues was investigated for the mussel, Perna canaliculus. The mussel larvae showed significantly faster settlement when exposed to the underwater noise produced by a 125-m long steel-hulled passenger and freight ferry. Median time to attachment on the substrata (ie settlement) was reduced by 22% and the time taken for all experimental larvae to settle was reduced by 40% relative to a silent control. There was no difference in the survival of the mussel larvae among the various noise treatments. The decrease in settlement time of the mussel larvae appeared to correlate with the intensity of the vessel sound, suggesting that underwater sound emanating from vessels may be an important factor in exacerbating hull fouling by mussels.

The hearing threshold of a harbor porpoise (Phocoena phocoena) for impulsive sounds (L).

PubMed

Kastelein, Ronald A; Gransier, Robin; Hoek, Lean; de Jong, Christ A F

2012-08-01

The distance at which harbor porpoises can hear underwater detonation sounds is unknown, but depends, among other factors, on the hearing threshold of the species for impulsive sounds. Therefore, the underwater hearing threshold of a young harbor porpoise for an impulsive sound, designed to mimic a detonation pulse, was quantified by using a psychophysical technique. The synthetic exponential pulse with a 5 ms time constant was produced and transmitted by an underwater projector in a pool. The resulting underwater sound, though modified by the response of the projection system and by the pool, exhibited the characteristic features of detonation sounds: A zero to peak sound pressure level of at least 30 dB (re 1 s(-1)) higher than the sound exposure level, and a short duration (34 ms). The animal's 50% detection threshold for this impulsive sound occurred at a received unweighted broadband sound exposure level of 60 dB re 1 μPa(2)s. It is shown that the porpoise's audiogram for short-duration tonal signals [Kastelein et al., J. Acoust. Soc. Am. 128, 3211-3222 (2010)] can be used to estimate its hearing threshold for impulsive sounds.

Underwater sound of rigid-hulled inflatable boats.

PubMed

Erbe, Christine; Liong, Syafrin; Koessler, Matthew Walter; Duncan, Alec J; Gourlay, Tim

2016-06-01

Underwater sound of rigid-hulled inflatable boats was recorded 142 times in total, over 3 sites: 2 in southern British Columbia, Canada, and 1 off Western Australia. Underwater sound peaked between 70 and 400 Hz, exhibiting strong tones in this frequency range related to engine and propeller rotation. Sound propagation models were applied to compute monopole source levels, with the source assumed 1 m below the sea surface. Broadband source levels (10-48 000 Hz) increased from 134 to 171 dB re 1 μPa @ 1 m with speed from 3 to 16 m/s (10-56 km/h). Source power spectral density percentile levels and 1/3 octave band levels are given for use in predictive modeling of underwater sound of these boats as part of environmental impact assessments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, Jayson J.; Myers, Joshua R.; Carlson, Thomas J.

The purpose of this study was to design and build two versions of an underwater sound recording device. The device designed is referred to as the Underwater Sound Recorder (USR), which can be connected to one or two hydrophones or other underwater sound sensors. The URS contains a 26 dB preamplifier and a user selectable gain that permits additional amplification of input to the system from 26 dB to 46 dB. Signals within the frequency range up to 15 kHz may be recorded using the USR. Examples of USR applications are monitoring underwater processes that have the potential to createmore » large pressure waves that could potentially harm fish or other aquatic life, such as underwater explosions or pile driving. Additional applications are recording sound generated by vessels or the vocalizations of some marine mammals, such as the calls from many species of whales.« less

Modeling the utility of binaural cues for underwater sound localization.

PubMed

Schneider, Jennifer N; Lloyd, David R; Banks, Patchouly N; Mercado, Eduardo

2014-06-01

The binaural cues used by terrestrial animals for sound localization in azimuth may not always suffice for accurate sound localization underwater. The purpose of this research was to examine the theoretical limits of interaural timing and level differences available underwater using computational and physical models. A paired-hydrophone system was used to record sounds transmitted underwater and recordings were analyzed using neural networks calibrated to reflect the auditory capabilities of terrestrial mammals. Estimates of source direction based on temporal differences were most accurate for frequencies between 0.5 and 1.75 kHz, with greater resolution toward the midline (2°), and lower resolution toward the periphery (9°). Level cues also changed systematically with source azimuth, even at lower frequencies than expected from theoretical calculations, suggesting that binaural mechanical coupling (e.g., through bone conduction) might, in principle, facilitate underwater sound localization. Overall, the relatively limited ability of the model to estimate source position using temporal and level difference cues underwater suggests that animals such as whales may use additional cues to accurately localize conspecifics and predators at long distances. Copyright © 2014 Elsevier B.V. All rights reserved.

Underwater hearing and sound localization with and without an air interface.

PubMed

Shupak, Avi; Sharoni, Zohara; Yanir, Yoav; Keynan, Yoav; Alfie, Yechezkel; Halpern, Pinchas

2005-01-01

Underwater hearing acuity and sound localization are improved by the presence of an air interface around the pinnae and inside the external ear canals. Hearing threshold and the ability to localize sound sources are reduced underwater. The resonance frequency of the external ear is lowered when the external ear canal is filled with water, and the impedance-matching ability of the middle ear is significantly reduced due to elevation of the ambient pressure, the water-mass load on the tympanic membrane, and the addition of a fluid-air interface during submersion. Sound lateralization on land is largely explained by the mechanisms of interaural intensity differences and interaural temporal or phase differences. During submersion, these differences are largely lost due to the increase in underwater sound velocity and cancellation of the head's acoustic shadow effect because of the similarity between the impedance of the skull and the surrounding water. Ten scuba divers wearing a regular opaque face mask or an opaque ProEar 2000 (Safe Dive, Ltd., Hofit, Israel) mask that enables the presence of air at ambient pressure in and around the ear made a dive to a depth of 3 m in the open sea. Four underwater speakers arranged on the horizontal plane at 90-degree intervals and at a distance of 5 m from the diver were used for testing pure-tone hearing thresholds (PTHT), the reception threshold for the recorded sound of a rubber-boat engine, and sound localization. For sound localization, the sound of the rubber boat's engine was randomly delivered by one speaker at a time at 40 dB HL above the recorded sound of a rubber-boat engine, and the diver was asked to point to the sound source. The azimuth was measured by the diver's companion using a navigation board. Underwater PTHT with both masks were significantly higher for frequencies of 250 to 6000 Hz when compared with the thresholds on land (p <0.0001). No differences were found in the PTHT or the reception threshold for the recorded sound of a rubber-boat engine for dry or wet ear conditions. There was no difference in the sound localization error between the regular mask and the ProEar 2000 mask. The presence of air around the pinna and inside the external ear canal did not improve underwater hearing sensitivity or sound localization. These results support the argument that bone conduction plays the main role in underwater hearing.

Extending The Calibration In The Underwater Sound Reference Division (USRD) Reciprocity Coupler To Incorporate Phase

DTIC Science & Technology

2016-09-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS EXTENDING THE CALIBRATION IN THE UNDERWATER SOUND REFERENCE DIVISION (USRD) RECIPROCITY COUPLER...AND DATES COVERED Master’s Thesis 08-01-2014 to 08-21-2016 4. TITLE AND SUBTITLE EXTENDING THE CALIBRATION IN THE UNDERWATER SOUND REFERENCE DIVISION...SPONSORING / MONITORING AGENCY REPORT NUMBER 11. SUPPLEMENTARY NOTES The views expressed in this document are those of the author and do not reflect

Specialization for underwater hearing by the tympanic middle ear of the turtle, Trachemys scripta elegans

PubMed Central

Christensen-Dalsgaard, Jakob; Brandt, Christian; Willis, Katie L.; Christensen, Christian Bech; Ketten, Darlene; Edds-Walton, Peggy; Fay, Richard R.; Madsen, Peter T.; Carr, Catherine E.

2012-01-01

Turtles, like other amphibious animals, face a trade-off between terrestrial and aquatic hearing. We used laser vibrometry and auditory brainstem responses to measure their sensitivity to vibration stimuli and to airborne versus underwater sound. Turtles are most sensitive to sound underwater, and their sensitivity depends on the large middle ear, which has a compliant tympanic disc attached to the columella. Behind the disc, the middle ear is a large air-filled cavity with a volume of approximately 0.5 ml and a resonance frequency of approximately 500 Hz underwater. Laser vibrometry measurements underwater showed peak vibrations at 500–600 Hz with a maximum of 300 µm s−1 Pa−1, approximately 100 times more than the surrounding water. In air, the auditory brainstem response audiogram showed a best sensitivity to sound of 300–500 Hz. Audiograms before and after removing the skin covering reveal that the cartilaginous tympanic disc shows unchanged sensitivity, indicating that the tympanic disc, and not the overlying skin, is the key sound receiver. If air and water thresholds are compared in terms of sound intensity, thresholds in water are approximately 20–30 dB lower than in air. Therefore, this tympanic ear is specialized for underwater hearing, most probably because sound-induced pulsations of the air in the middle ear cavity drive the tympanic disc. PMID:22438494

Specialization for underwater hearing by the tympanic middle ear of the turtle, Trachemys scripta elegans.

PubMed

Christensen-Dalsgaard, Jakob; Brandt, Christian; Willis, Katie L; Christensen, Christian Bech; Ketten, Darlene; Edds-Walton, Peggy; Fay, Richard R; Madsen, Peter T; Carr, Catherine E

2012-07-22

Turtles, like other amphibious animals, face a trade-off between terrestrial and aquatic hearing. We used laser vibrometry and auditory brainstem responses to measure their sensitivity to vibration stimuli and to airborne versus underwater sound. Turtles are most sensitive to sound underwater, and their sensitivity depends on the large middle ear, which has a compliant tympanic disc attached to the columella. Behind the disc, the middle ear is a large air-filled cavity with a volume of approximately 0.5 ml and a resonance frequency of approximately 500 Hz underwater. Laser vibrometry measurements underwater showed peak vibrations at 500-600 Hz with a maximum of 300 µm s(-1) Pa(-1), approximately 100 times more than the surrounding water. In air, the auditory brainstem response audiogram showed a best sensitivity to sound of 300-500 Hz. Audiograms before and after removing the skin covering reveal that the cartilaginous tympanic disc shows unchanged sensitivity, indicating that the tympanic disc, and not the overlying skin, is the key sound receiver. If air and water thresholds are compared in terms of sound intensity, thresholds in water are approximately 20-30 dB lower than in air. Therefore, this tympanic ear is specialized for underwater hearing, most probably because sound-induced pulsations of the air in the middle ear cavity drive the tympanic disc.

Topological phononic states of underwater sound based on coupled ring resonators

DOE Office of Scientific and Technical Information (OSTI.GOV)

He, Cheng; Li, Zheng; Ni, Xu

We report a design of topological phononic states for underwater sound using arrays of acoustic coupled ring resonators. In each individual ring resonator, two degenerate acoustic modes, corresponding to clockwise and counter-clockwise propagation, are treated as opposite pseudospins. The gapless edge states arise in the bandgap resulting in protected pseudospin-dependent sound transportation, which is a phononic analogue of the quantum spin Hall effect. We also investigate the robustness of the topological sound state, suggesting that the observed pseudospin-dependent sound transportation remains unless the introduced defects facilitate coupling between the clockwise and counter-clockwise modes (in other words, the original mode degeneracymore » is broken). The topological engineering of sound transportation will certainly promise unique design for next generation of acoustic devices in sound guiding and switching, especially for underwater acoustic devices.« less

Experiments on the mechanism of underwater hearing.

PubMed

Pau, Hans Wilhelm; Warkentin, Mareike; Specht, Olaf; Krentz, Helga; Herrmann, Anne; Ehrt, Karsten

2011-12-01

The findings suggest that underwater sound perception is realized by the middle ear rather than by bone conduction, at least in shallow water conditions. To prove whether underwater sound perception is effected by bone conduction or by conduction via the middle ear. Five divers, breathing through snorkels, were tested in a swimming pool, to determine whether a sound was louder when the acoustic source placed was in front of the head in comparison with a lateral application facing the ear region. The second experiment investigated whether sound perception is influenced by ear protection plugs in underwater conditions. Also, the effect of a 5 mm thick neoprene hood was determined, with and without an additional perforation in the ear region. Sounds were louder when applied from a position laterally facing the ear, louder without than with a protection plug, louder without than with a neoprene hood on, and louder when the neoprene hood had a perforation in the region of the ear than with an intact hood.

Location, location, location: finding a suitable home among the noise

PubMed Central

Stanley, Jenni A.; Radford, Craig A.; Jeffs, Andrew G.

2012-01-01

While sound is a useful cue for guiding the onshore orientation of larvae because it travels long distances underwater, it also has the potential to convey valuable information about the quality and type of the habitat at the source. Here, we provide, to our knowledge, the first evidence that settlement-stage coastal crab species can interpret and show a strong settlement and metamorphosis response to habitat-related differences in natural underwater sound. Laboratory- and field-based experiments demonstrated that time to metamorphosis in the settlement-stage larvae of common coastal crab species varied in response to different underwater sound signatures produced by different habitat types. The megalopae of five species of both temperate and tropical crabs showed a significant decrease in time to metamorphosis, when exposed to sound from their optimal settlement habitat type compared with other habitat types. These results indicate that sounds emanating from specific underwater habitats may play a major role in determining spatial patterns of recruitment in coastal crab species. PMID:22673354

Behavioural Response Thresholds in New Zealand Crab Megalopae to Ambient Underwater Sound

PubMed Central

Stanley, Jenni A.; Radford, Craig A.; Jeffs, Andrew G.

2011-01-01

A small number of studies have demonstrated that settlement stage decapod crustaceans are able to detect and exhibit swimming, settlement and metamorphosis responses to ambient underwater sound emanating from coastal reefs. However, the intensity of the acoustic cue required to initiate the settlement and metamorphosis response, and therefore the potential range over which this acoustic cue may operate, is not known. The current study determined the behavioural response thresholds of four species of New Zealand brachyuran crab megalopae by exposing them to different intensity levels of broadcast reef sound recorded from their preferred settlement habitat and from an unfavourable settlement habitat. Megalopae of the rocky-reef crab, Leptograpsus variegatus, exhibited the lowest behavioural response threshold (highest sensitivity), with a significant reduction in time to metamorphosis (TTM) when exposed to underwater reef sound with an intensity of 90 dB re 1 µPa and greater (100, 126 and 135 dB re 1 µPa). Megalopae of the mud crab, Austrohelice crassa, which settle in soft sediment habitats, exhibited no response to any of the underwater reef sound levels. All reef associated species exposed to sound levels from an unfavourable settlement habitat showed no significant change in TTM, even at intensities that were similar to their preferred reef sound for which reductions in TTM were observed. These results indicated that megalopae were able to discern and respond selectively to habitat-specific acoustic cues. The settlement and metamorphosis behavioural response thresholds to levels of underwater reef sound determined in the current study of four species of crabs, enables preliminary estimation of the spatial range at which an acoustic settlement cue may be operating, from 5 m to 40 km depending on the species. Overall, these results indicate that underwater sound is likely to play a major role in influencing the spatial patterns of settlement of coastal crab species. PMID:22163314

Ejectable underwater sound source recovery assembly

NASA Technical Reports Server (NTRS)

Irick, S. C. (Inventor)

1974-01-01

An underwater sound source is described that may be ejectably mounted on any mobile device that travels over water, to facilitate in the location and recovery of the device when submerged. A length of flexible line maintains a connection between the mobile device and the sound source. During recovery, the sound source is located be particularly useful in the recovery of spent rocket motors that bury in the ocean floor upon impact.

Acoustic characteristics of underwater tail slaps used by Norwegian and Icelandic killer whales (Orcinus orca) to debilitate herring (Clupea harengus).

PubMed

Simon, Malene; Wahlberg, Magnus; Ugarte, Fernando; Miller, Lee A

2005-06-01

Norwegian killer whales debilitate prey by slapping their tails into herring schools. These underwater tail slaps produce a thud-like sound. It is unclear whether this sound is caused by cavitation and/or physical contact between herring and whale tail. Also the forces causing debilitation of the fish are not understood. Here we present an acoustic analysis of underwater tail slaps using a multi-channel wide (150 kHz) band recording system. Underwater tail slaps produced by Norwegian killer whales generated sounds consisting of multiple pulses with source levels of 186+/-5.4 dB (pp) re.1 microPa at 1 m (+/-1 s.d., N = 4). The -3 dB and 97% energy bandwidths were 36.8+/-22.5 kHz and 130.5+/-17.5 kHz (+/-1 s.d., N = 13), respectively, with a centre frequency of 46.1+/-22.3 kHz. The similarities between the acoustic properties of underwater tail slaps recorded from killer whales in Norway, and thud-like sounds recorded from killer whales in Iceland suggest that Norwegian and Icelandic killer whales use similar hunting techniques. The acoustic characteristics of sounds produced by underwater tail slaps were similar to the ones from other cavitation sound sources described in the literature, both in term of temporal and frequency features as well as in source level. We suggest that multiple factors generated by the tail slaps like particle fluctuations, turbulence, pressure changes and physical impact cause debilitation of herring.

A noisy spring: the impact of globally rising underwater sound levels on fish.

PubMed

Slabbekoorn, Hans; Bouton, Niels; van Opzeeland, Ilse; Coers, Aukje; ten Cate, Carel; Popper, Arthur N

2010-07-01

The underwater environment is filled with biotic and abiotic sounds, many of which can be important for the survival and reproduction of fish. Over the last century, human activities in and near the water have increasingly added artificial sounds to this environment. Very loud sounds of relatively short exposure, such as those produced during pile driving, can harm nearby fish. However, more moderate underwater noises of longer duration, such as those produced by vessels, could potentially impact much larger areas, and involve much larger numbers of fish. Here we call attention to the urgent need to study the role of sound in the lives of fish and to develop a better understanding of the ecological impact of anthropogenic noise. Copyright 2010 Elsevier Ltd. All rights reserved.

Diel patterns in underwater sounds produced by beluga whales and Pacific white-sided dolphins at John G. Shedd Aquarium

NASA Astrophysics Data System (ADS)

Brickman, Jon; Tanchez, Erin; Thomas, Jeanette

2005-09-01

Diel patterns in underwater sounds from five beluga whales (Delphinapterus leucas) and five Pacific white-sided dolphins (Lagenorhynchus obliquidens) housed at John G. Shedd Aquarium in Chicago, IL were studied. Underwater sounds were sampled systematically over 24-h periods by using a battery-operated cassette recorder and an Ithaco 605C hydrophone controlled by a digital timer, which activated every hour and then shut off after 2.5 min. Belugas had 14 sounds and Pacific white-sided dolphins produced 5 sounds. For each species, the use of some sounds was correlated with other sounds. The diel pattern for both species was similar and mostly affected by the presence of humans. Sounds gradually increased after the staff and visitors arrived, peaked during the midday, gradually decreased as closing of the aquarium approached, and was minimal overnight. These data can help identify the best time of day to make recordings and perhaps could be used to examine social, reproductive, or health changes in these captive cetaceans.

Underwater Sound Propagation from Marine Pile Driving.

PubMed

Reyff, James A

2016-01-01

Pile driving occurs in a variety of nearshore environments that typically have very shallow-water depths. The propagation of pile-driving sound in water is complex, where sound is directly radiated from the pile as well as through the ground substrate. Piles driven in the ground near water bodies can produce considerable underwater sound energy. This paper presents examples of sound propagation through shallow-water environments. Some of these examples illustrate the substantial variation in sound amplitude over time that can be critical to understand when computing an acoustic-based safety zone for aquatic species.

An investigation of underwater sound propagation from pile driving.

DOT National Transportation Integrated Search

2011-12-01

The underwater noise from impact pile driving was studied by using a finite element model for the sound generation and a parabolic equation model for propagation. Results were compared with measurements taken with a vertical line array deployed durin...

Experimental demonstration of remote, passive acousto-optic sensing.

PubMed

Antonelli, Lynn; Blackmon, Fletcher

2004-12-01

Passively detecting underwater sound from the air can allow aircraft and surface vessels to monitor the underwater acoustic environment. Experimental research into an optical hydrophone is being conducted for remote, aerial detection of underwater sound. A laser beam is directed onto the water surface to measure the velocity of the vibrations occurring as the underwater acoustic signal reaches the water surface. The acoustically generated surface vibrations modulate the phase of the laser beam. Sound detection occurs when the laser is reflected back towards the sensor. Therefore, laser alignment on the specularly reflecting water surface is critical. As the water surface moves, the laser beam is reflected away from the photodetector and no signal is obtained. One option to mitigate this problem is to continually steer the laser onto a spot on the water surface that provides a direct back-reflection. Results are presented from a laboratory test that investigates the feasibility of the acousto-optic sensor detection on hydrostatic and hydrodynamic surfaces using a laser Doppler vibrometer in combination with a laser-based, surface normal glint tracker for remotely detecting underwater sound. This paper outlines the acousto-optic sensor and tracker concepts and presents experimental results comparing sensor operation under various sea surface conditions.

Underwater Sound: Deep-Ocean Propagation: Variations of temperature and pressure have great influence on the propagation of sound in the ocean.

PubMed

Frosch, R A

1964-11-13

The absorption of sound in sea water varies markedly with frequency, being much greater at high than at low frequencies. It is sufficiently small at frequencies below several kilocycles per second, however, to permit propagation to thousands of miles. Oceanographic factors produce variations in sound velocity with depth, and these variations have a strong influence on long-range propagation. The deep ocean is characterized by a strong channel, generally at a depth of 500 to 1500 meters. In addition to guided propagation in this channel, the velocity structure gives rise to strongly peaked propagation from surface sources to surface receivers 48 to 56 kilometers away, with strong shadow zones of weak intensity in between. The near-surface shadow zone, in the latter case, may be filled in by bottom reflections or near-surface guided propagation due to a surface isothermal layer. The near-surface shadow zones can be avoided with certainty only through locating sources and receivers deep in the ocean.

Three Dimensional Underwater Sound Propagation Over Sloping Bottoms

NASA Astrophysics Data System (ADS)

Glegg, Stewart A. L.; Riley, J. M.

This article reviews the work which has been carried out over the past few years on three dimensional underwater sound propagation over sloping bottoms. When sound propagates across a slope three dimensional effects can cause shadow zones and mode cut off effects to occur, which could not be predicted by a two dimensional model. For many years the theory for this type of propagation over realistic ocean floors, which can support both compressional and shear waves, eluded workers in this field. Recently the complete solution for the acoustic field in a "wedge domain with penetrable boundaries" has been developed, and this has allowed for complete understanding of three dimensional bottom interacting sound propagation. These theories have been verified by a series of laboratory scale experiments and excellent agreement has been obtained. However only one full scale ocean experiment has been carried out on three dimensional, bottom interacting, acoustic propagation. This showed significant horizontal refraction of sound propagating across a continental slope and further verifies the importance of bottom slopes on underwater sound propagation.

Effects of Underwater Sound Simulating the Intermediate Scale Measurement System on Fish and Zooplankton of Lake Pend Oreille, Idaho

DTIC Science & Technology

1994-05-01

Micrptens salmoides Black crappie Pomozfs nigromaculafts Esocidae Northern pike Esox lucius Saimonidae Kokanee Oncodunchus nerka Rainbow trout Oncorhynchus ...1969. Underwater noise spectra, fish sounds and response to low frequencies of cutthroat trout Oncorhynchus clari with reference to orientation and

Attenuation of low-frequency underwater sound using an array of air-filled balloons and comparison to effective medium theory.

PubMed

Lee, Kevin M; Wilson, Preston S; Wochner, Mark S

2017-12-01

The ultimate goal of this work is to accurately predict the attenuation through a collection of large (on the order of 10-cm-radius) tethered encapsulated bubbles used in underwater noise abatement systems. Measurements of underwater sound attenuation were performed during a set of lake experiments, where a low-frequency compact electromechanical sound source was surrounded by different arrays of encapsulated bubbles with various individual bubbles sizes and void fractions. The measurements were compared with an existing predictive model [Church, J. Acoust. Soc. Am. 97, 1510-1521 (1995)] of the dispersion relation for linear propagation in liquid containing encapsulated bubbles. Although the model was originally intended to describe ultrasound contrast agents, it is evaluated here for large bubbles, and hence low frequencies, as a design tool for future underwater noise abatement systems, and there is good quantitative agreement between the observations and the model.

Underwater sound radiation patterns of contemporary merchant ships

NASA Astrophysics Data System (ADS)

Gassmann, M.; Wiggins, S. M.; Hildebrand, J. A.

2016-12-01

Merchant ships radiate underwater sound as an unintended by-product of their operation and as consequence contribute significantly to low-frequency, man-made noise in the ocean. Current measurement standards for the description of underwater sound from ships (ISO 17208-1:2016 and ANSI S12.64-2009) require nominal hydrophone depths of 15°, 30° and 45° at the starboard and portside of the test vessel.To opportunistically study the underwater sound of contemporary merchant ships that were tracked by the Automatic Identification System (AIS), an array of seven high-frequency acoustic recording packages (HARPs) with a sampling frequency of 200 kHz was deployed in the Santa Barbara Channel in the primary outgoing shipping lane for the port of Los Angeles and Long Beach. The vertical and horizontal aperture of the array allowed for starboard and portside measurements at all standard-required nominal hydrophone depths in addition to measurements taken at the keel aspect. Based on these measurements, frequency-dependent radiation patterns of contemporary merchant ships were estimated and used to evaluate current standards for computing ship source levels.

Characterizing large river sounds: Providing context for understanding the environmental effects of noise produced by hydrokinetic turbines.

PubMed

Bevelhimer, Mark S; Deng, Z Daniel; Scherelis, Constantin

2016-01-01

Underwater noise associated with the installation and operation of hydrokinetic turbines in rivers and tidal zones presents a potential environmental concern for fish and marine mammals. Comparing the spectral quality of sounds emitted by hydrokinetic turbines to natural and other anthropogenic sound sources is an initial step at understanding potential environmental impacts. Underwater recordings were obtained from passing vessels and natural underwater sound sources in static and flowing waters. Static water measurements were taken in a lake with minimal background noise. Flowing water measurements were taken at a previously proposed deployment site for hydrokinetic turbines on the Mississippi River, where sounds created by flowing water are part of all measurements, both natural ambient and anthropogenic sources. Vessel sizes ranged from a small fishing boat with 60 hp outboard motor to an 18-unit barge train being pushed upstream by tugboat. As expected, large vessels with large engines created the highest sound levels, which were, on average, 40 dB greater than the sound created by an operating hydrokinetic turbine. A comparison of sound levels from the same sources at different distances using both spherical and cylindrical sound attenuation functions suggests that spherical model results more closely approximate observed sound attenuation.

The low-frequency sound power measuring technique for an underwater source in a non-anechoic tank

NASA Astrophysics Data System (ADS)

Zhang, Yi-Ming; Tang, Rui; Li, Qi; Shang, Da-Jing

2018-03-01

In order to determine the radiated sound power of an underwater source below the Schroeder cut-off frequency in a non-anechoic tank, a low-frequency extension measuring technique is proposed. This technique is based on a unique relationship between the transmission characteristics of the enclosed field and those of the free field, which can be obtained as a correction term based on previous measurements of a known simple source. The radiated sound power of an unknown underwater source in the free field can thereby be obtained accurately from measurements in a non-anechoic tank. To verify the validity of the proposed technique, a mathematical model of the enclosed field is established using normal-mode theory, and the relationship between the transmission characteristics of the enclosed and free fields is obtained. The radiated sound power of an underwater transducer source is tested in a glass tank using the proposed low-frequency extension measuring technique. Compared with the free field, the radiated sound power level of the narrowband spectrum deviation is found to be less than 3 dB, and the 1/3 octave spectrum deviation is found to be less than 1 dB. The proposed testing technique can be used not only to extend the low-frequency applications of non-anechoic tanks, but also for measurement of radiated sound power from complicated sources in non-anechoic tanks.

Underwater auditory localization by a swimming harbor seal (Phoca vitulina).

PubMed

Bodson, Anais; Miersch, Lars; Mauck, Bjoern; Dehnhardt, Guido

2006-09-01

The underwater sound localization acuity of a swimming harbor seal (Phoca vitulina) was measured in the horizontal plane at 13 different positions. The stimulus was either a double sound (two 6-kHz pure tones lasting 0.5 s separated by an interval of 0.2 s) or a single continuous sound of 1.2 s. Testing was conducted in a 10-m-diam underwater half circle arena with hidden loudspeakers installed at the exterior perimeter. The animal was trained to swim along the diameter of the half circle and to change its course towards the sound source as soon as the signal was given. The seal indicated the sound source by touching its assumed position at the board of the half circle. The deviation of the seals choice from the actual sound source was measured by means of video analysis. In trials with the double sound the seal localized the sound sources with a mean deviation of 2.8 degrees and in trials with the single sound with a mean deviation of 4.5 degrees. In a second experiment minimum audible angles of the stationary animal were found to be 9.8 degrees in front and 9.7 degrees in the back of the seal's head.

Characterizing large river sounds: Providing context for understanding the environmental effects of noise produced by hydrokinetic turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bevelhimer, Mark S.; Deng, Z. Daniel; Scherelis, Constantin

2016-01-01

Underwater noise associated with the installation and operation of hydrokinetic turbines in rivers and tidal zones presents a potential environmental concern for fish and marine mammals. Comparing the spectral quality of sounds emitted by hydrokinetic turbines to natural and other anthropogenic sound sources is an initial step at understanding potential environmental impacts. Underwater recordings were obtained from passing vessels of different sizes and other underwater sound sources in both static and flowing waters. Static water measurements were taken in a lake with minimal background noise. Flowing water measurements were taken at a previously proposed deployment site for hydrokinetic turbines onmore » the Mississippi River, where the sound of flowing water is included in background measurements. The size of vessels measured ranged from a small fishing boat with a 60 HP outboard motor to an 18-unit barge train being pushed upstream by tugboat. As expected, large vessels with large engines created the highest sound levels, and when compared to the sound created by an operating HK turbine were many times greater. A comparison of sound levels from the same sources at different distances using both spherical and cylindrical sound attenuation functions suggests that spherical model results more closely approximate observed values.« less

Prediction of drilling site-specific interaction of industrial acoustic stimuli and endangered whales: Beaufort Sea (1985). Final report, July 1985-March 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miles, P.R.; Malme, C.I.; Shepard, G.W.

1986-10-01

Research was performed during the first year (1985) of the two-year project investigating potential responsiveness of bowhead and gray whales to underwater sounds associated with offshore oil-drilling sites in the Alaskan Beaufort Sea. The underwater acoustic environment and sound propagation characteristics of five offshore sites were determined. Estimates of industrial noise levels versus distance from those sites are provided. LGL Ltd. (bowhead) and BBN (gray whale) jointly present zones of responsiveness of these whales to typical underwater sounds (drillship, dredge, tugs, drilling at gravel island). An annotated bibliography regarding the potential effects of offshore industrial noise on bowhead whales inmore » the Beaufort Sea is included.« less

Minimizing noise in fiberglass aquaculture tanks: Noise reduction potential of various retrofits

USGS Publications Warehouse

Davidson, J.; Frankel, A.S.; Ellison, W.T.; Summerfelt, S.; Popper, A.N.; Mazik, P.; Bebak, J.

2007-01-01

Equipment used in intensive aquaculture systems, such as pumps and blowers can produce underwater sound levels and frequencies within the range of fish hearing. The impacts of underwater noise on fish are not well known, but limited research suggests that subjecting fish to noise could result in impairment of the auditory system, reduced growth rates, and increased stress. Consequently, reducing sound in fish tanks could result in advantages for cultured species and increased productivity for the aquaculture industry. The objective of this study was to evaluate the noise reduction potential of various retrofits to fiberglass fish culture tanks. The following structural changes were applied to tanks to reduce underwater noise: (1) inlet piping was suspended to avoid contact with the tank, (2) effluent piping was disconnected from a common drain line, (3) effluent piping was insulated beneath tanks, and (4) tanks were elevated on cement blocks and seated on insulated padding. Four combinations of the aforementioned structural changes were evaluated in duplicate and two tanks were left unchanged as controls. Control tanks had sound levels of 120.6 dB re 1 ??Pa. Each retrofit contributed to a reduction of underwater sound. As structural changes were combined, a cumulative reduction in sound level was observed. Tanks designed with a combination of retrofits had sound levels of 108.6 dB re 1 ??Pa, a four-fold reduction in sound pressure level. Sound frequency spectra indicated that the greatest sound reductions occurred between 2 and 100 Hz and demonstrated that nearby pumps and blowers created tonal frequencies that were transmitted into the tanks. The tank modifications used during this study were simple and inexpensive and could be applied to existing systems or considered when designing aquaculture facilities. ?? 2007 Elsevier B.V. All rights reserved.

Neoprene wet-suit hood affects low-frequency underwater hearing thresholds.

PubMed

Fothergill, David M; Sims, John R; Curley, Michael D

2004-05-01

Psychophysical measures of wet-suit hood sound attenuation are needed to provide the diving community with guidance on protection from underwater sound. Underwater hearing thresholds were obtained from 15 male and 5 female recreational divers with and without a 3-mm thick wet-suit hood. Dives were conducted at a depth of 1 m in a large quiet anechoic pool. Thresholds were determined using a two-interval forced-choice procedure with a 0.71 probability of positive response at convergence. A 1-s pure tone was presented with a 20-ms rise and fall time at 100, 200, 250, 300, 400, and 500 Hz. Without a wet-suit hood, mean thresholds decreased from 99 dB re 1 microPa at 100 Hz to 85 dB at 500 Hz. Thresholds were statistically similar at 100 to 300 Hz with and without the wet-suit hood, but were significantly increased at 400 and 500 Hz with the hood (p < 0.001). In conclusion, at shallow depths, a 3-mm neoprene wet-suit hood attenuates underwater sound by approximately 10 dB for frequencies between 400 Hz and 500 Hz. At frequencies below 400 Hz, a 3-mm neoprene wet-suit hood offers no sound protection.

Auditory and behavioral responses of bottlenose dolphins (Tursiops truncatus) and a beluga whale (Delphinapterus leucas) to impulsive sounds resembling distant signatures of underwater explosions.

PubMed

Finneran, J J; Schlundt, C E; Carder, D A; Clark, J A; Young, J A; Gaspin, J B; Ridgway, S H

2000-07-01

A behavioral response paradigm was used to measure masked underwater hearing thresholds in two bottlenose dolphins and one beluga whale before and after exposure to impulsive underwater sounds with waveforms resembling distant signatures of underwater explosions. An array of piezoelectric transducers was used to generate impulsive sounds with waveforms approximating those predicted from 5 or 500 kg HBX-1 charges at ranges from 1.5 to 55.6 km. At the conclusion of the study, no temporary shifts in masked-hearing thresholds (MTTSs), defined as a 6-dB or larger increase in threshold over pre-exposure levels, had been observed at the highest impulse level generated (500 kg at 1.7 km, peak pressure 70 kPa); however, disruptions of the animals' trained behaviors began to occur at exposures corresponding to 5 kg at 9.3 km and 5 kg at 1.5 km for the dolphins and 500 kg at 1.9 km for the beluga whale. These data are the first direct information regarding the effects of distant underwater explosion signatures on the hearing abilities of odontocetes.

Threshold Monitoring Maps for Under-Water Explosions

NASA Astrophysics Data System (ADS)

Arora, N. S.

2014-12-01

Hydro-acoustic energy in the 1-100 Hz range from under-water explosions can easily spread for thousands of miles due to the unique properties of the deep sound channel. This channel, aka SOFAR channel, exists almost everywhere in the earth's oceans where the water has at least 1500m depth. Once the energy is trapped in this channel it spreads out cylindrically, and hence experiences very little loss, as long as there is an unblocked path from source to receiver. Other losses such as absorption due to chemicals in the ocean (mainly boric acid and magnesium sulphate) are also quite minimal at these low frequencies. It is not surprising then that the International Monitoring System (IMS) maintains a global network of hydrophone stations listening on this particular frequency range. The overall objective of our work is to build a probabilistic model to detect and locate under-water explosions using the IMS network. A number of critical pieces for this model, such as travel time predictions, are already well known. We are extending the existing knowledge-base by building the remaining pieces, most crucially the models for transmission losses and detection probabilities. With a complete model for detecting under-water explosions we are able to combine it with our existing model for seismic events, NET-VISA. In the conference we will present threshold monitoring maps for explosions in the earth's oceans. Our premise is that explosive sources release an unknown fraction of their total energy into the SOFAR channel, and this trapped energy determines their detection probability at each of the IMS hydrophone stations. Our threshold monitoring maps compute the minimum amount of energy at each location that must be released into the deep sound channel such that there is a ninety percent probability that at least two of the IMS stations detect the event. We will also present results of our effort to detect and locate hydro-acoustic events. In particular, we will show results from a recent under-water volcanic eruption at the Ahyl Seamount (April-May 2014), and compare our work with the current processing, both automated and human, at the IDC.

Passive Mode Carbon Nanotube Underwater Acoustic Transducer

DTIC Science & Technology

2016-09-20

Acoustical transducer arrays can reflect a sound signal in reverse to the sender which can be used for echo location devices. [0008] In Jiang...of this layer of the medium determines the amplitude of the resulting sound waves. [0005] Recently, there has been development of underwater...structures. The energy is partially reflected from interfaces between the geologic structure and is detected with geophone or hydrophone sensors

Alaska North Shore Ocean Acoustics Study

DTIC Science & Technology

2015-09-30

effects of changing ice cover, wind patterns and circulation/upwelling on underwater sound propagation and ambient noise in the areas of continental ...noise field along the edge of Arctic continental shelf. Underwater sound propagation in Arctic oceans with ice cover is influenced by the elastic...von der Heydt has been implmenting the following system upgrades: 1. Replacing the existing Seascan timebase ( drift 2 to 3ms/day) with a

Hoeren unter Wasser: Absolute Reizschwellen und Richtungswahrnehnumg (Underwater Hearing: Absolute Thresholds and Sound Localization),

DTIC Science & Technology

The article deals first with the theoretical foundations of underwater hearing, and the effects of the acoustical characteristics of water on hearing...lead to the conclusion that, in water , man can locate the direction of sound at low and at very high tonal frequencies of the audio range, but this ability is probably vanishing in the middle range of frequencies. (Author)

Underwater sound from vessel traffic reduces the effective communication range in Atlantic cod and haddock.

PubMed

Stanley, Jenni A; Van Parijs, Sofie M; Hatch, Leila T

2017-11-07

Stellwagen Bank National Marine Sanctuary is located in Massachusetts Bay off the densely populated northeast coast of the United States; subsequently, the marine inhabitants of the area are exposed to elevated levels of anthropogenic underwater sound, particularly due to commercial shipping. The current study investigated the alteration of estimated effective communication spaces at three spawning locations for populations of the commercially and ecologically important fishes, Atlantic cod (Gadus morhua) and haddock (Melanogrammus aeglefinus). Both the ambient sound pressure levels and the estimated effective vocalization radii, estimated through spherical spreading models, fluctuated dramatically during the three-month recording periods. Increases in sound pressure level appeared to be largely driven by large vessel activity, and accordingly exhibited a significant positive correlation with the number of Automatic Identification System tracked vessels at the two of the three sites. The near constant high levels of low frequency sound and consequential reduction in the communication space observed at these recording sites during times of high vocalization activity raises significant concerns that communication between conspecifics may be compromised during critical biological periods. This study takes the first steps in evaluating these animals' communication spaces and alteration of these spaces due to anthropogenic underwater sound.

Investigation of the potential effects of underwater noise from petroleum-industry activities on feeding humpback whale behavior. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malme, C.I.; Miles, P.R.; Tyack, P.

1985-06-01

An investigation was made of the potential effects of underwater noise from petroleum-industry activities on the behavior of feeding humpback whales in Frederick Sound and Stephens Passage, Alaska in August, 1984. Test sounds were a 100 cu. in. air gun and playbacks of recorded drillship, drilling platform, production platform, semi-submersible drill rig, and helicopter fly-over noise. Sound source levels and acoustic propagation losses were measured. The movement patterns of whales were determined by observations of whale-surfacing positions.

RF Path and Absorption Loss Estimation for Underwater Wireless Sensor Networks in Different Water Environments

PubMed Central

Qureshi, Umair Mujtaba; Shaikh, Faisal Karim; Aziz, Zuneera; Shah, Syed M. Zafi S.; Sheikh, Adil A.; Felemban, Emad; Qaisar, Saad Bin

2016-01-01

Underwater Wireless Sensor Network (UWSN) communication at high frequencies is extremely challenging. The intricacies presented by the underwater environment are far more compared to the terrestrial environment. The prime reason for such intricacies are the physical characteristics of the underwater environment that have a big impact on electromagnetic (EM) signals. Acoustics signals are by far the most preferred choice for underwater wireless communication. Because high frequency signals have the luxury of large bandwidth (BW) at shorter distances, high frequency EM signals cannot penetrate and propagate deep in underwater environments. The EM properties of water tend to resist their propagation and cause severe attenuation. Accordingly, there are two questions that need to be addressed for underwater environment, first what happens when high frequency EM signals operating at 2.4 GHz are used for communication, and second which factors affect the most to high frequency EM signals. To answer these questions, we present real-time experiments conducted at 2.4 GHz in terrestrial and underwater (fresh water) environments. The obtained results helped in studying the physical characteristics (i.e., EM properties, propagation and absorption loss) of underwater environments. It is observed that high frequency EM signals can propagate in fresh water at a shallow depth only and can be considered for a specific class of applications such as water sports. Furthermore, path loss, velocity of propagation, absorption loss and the rate of signal loss in different underwater environments are also calculated and presented in order to understand why EM signals cannot propagate in sea water and oceanic water environments. An optimal solk6ution for underwater communication in terms of coverage distance, bandwidth and nature of communication is presented, along with possible underwater applications of UWSNs at 2.4 GHz. PMID:27322263

RF Path and Absorption Loss Estimation for Underwater Wireless Sensor Networks in Different Water Environments.

PubMed

Qureshi, Umair Mujtaba; Shaikh, Faisal Karim; Aziz, Zuneera; Shah, Syed M Zafi S; Sheikh, Adil A; Felemban, Emad; Qaisar, Saad Bin

2016-06-16

Underwater Wireless Sensor Network (UWSN) communication at high frequencies is extremely challenging. The intricacies presented by the underwater environment are far more compared to the terrestrial environment. The prime reason for such intricacies are the physical characteristics of the underwater environment that have a big impact on electromagnetic (EM) signals. Acoustics signals are by far the most preferred choice for underwater wireless communication. Because high frequency signals have the luxury of large bandwidth (BW) at shorter distances, high frequency EM signals cannot penetrate and propagate deep in underwater environments. The EM properties of water tend to resist their propagation and cause severe attenuation. Accordingly, there are two questions that need to be addressed for underwater environment, first what happens when high frequency EM signals operating at 2.4 GHz are used for communication, and second which factors affect the most to high frequency EM signals. To answer these questions, we present real-time experiments conducted at 2.4 GHz in terrestrial and underwater (fresh water) environments. The obtained results helped in studying the physical characteristics (i.e., EM properties, propagation and absorption loss) of underwater environments. It is observed that high frequency EM signals can propagate in fresh water at a shallow depth only and can be considered for a specific class of applications such as water sports. Furthermore, path loss, velocity of propagation, absorption loss and the rate of signal loss in different underwater environments are also calculated and presented in order to understand why EM signals cannot propagate in sea water and oceanic water environments. An optimal solk6ution for underwater communication in terms of coverage distance, bandwidth and nature of communication is presented, along with possible underwater applications of UWSNs at 2.4 GHz.

Sonic Kayaks: Environmental monitoring and experimental music by citizens.

PubMed

Griffiths, Amber G F; Kemp, Kirsty M; Matthews, Kaffe; Garrett, Joanne K; Griffiths, David J

2017-11-01

The Sonic Kayak is a musical instrument used to investigate nature and developed during open hacklab events. The kayaks are rigged with underwater environmental sensors, which allow paddlers to hear real-time water temperature sonifications and underwater sounds, generating live music from the marine world. Sensor data is also logged every second with location, time and date, which allows for fine-scale mapping of water temperatures and underwater noise that was previously unattainable using standard research equipment. The system can be used as a citizen science data collection device, research equipment for professional scientists, or a sound art installation in its own right.

Sonic Kayaks: Environmental monitoring and experimental music by citizens

PubMed Central

Kemp, Kirsty M.; Matthews, Kaffe; Garrett, Joanne K.; Griffiths, David J.

2017-01-01

The Sonic Kayak is a musical instrument used to investigate nature and developed during open hacklab events. The kayaks are rigged with underwater environmental sensors, which allow paddlers to hear real-time water temperature sonifications and underwater sounds, generating live music from the marine world. Sensor data is also logged every second with location, time and date, which allows for fine-scale mapping of water temperatures and underwater noise that was previously unattainable using standard research equipment. The system can be used as a citizen science data collection device, research equipment for professional scientists, or a sound art installation in its own right. PMID:29190283

Wide Area Detection and Identification of Underwater UXO Using Structural Acoustic Sensors

DTIC Science & Technology

2011-02-01

measurements of underwater unexploded ordnance (UXO),” J. Acoustic. Soc. Am. 123, 738-746 (2008). 10. R. J. Urick , “Principles of Underwater Sound... Urick , op. cit., pp 291-327. 14. S. Dey and D.K. Datta, “A parrallel hp-FEM infrastructure for three-dimensional structural acoustics,” Int. J

[The underwater and airborne horizontal localization of sound by the northern fur seal].

PubMed

Babushina, E S; Poliakov, M A

2004-01-01

The accuracy of the underwater and airborne horizontal localization of different acoustic signals by the northern fur seal was investigated by the method of instrumental conditioned reflexes with food reinforcement. For pure-tone pulsed signals in the frequency range of 0.5-25 kHz the minimum angles of sound localization at 75% of correct responses corresponded to sound transducer azimuth of 6.5-7.5 degrees +/- 0.1-0.4 degrees underwater (at impulse duration of 3-90 ms) and of 3.5-5.5 degrees +/- 0.05-0.5 degrees in air (at impulse duration of 3-160 ms). The source of pulsed noise signals (of 3-ms duration) was localized with the accuracy of 3.0 degrees +/- 0.2 degrees underwater. The source of continuous (of 1-s duration) narrow band (10% of c.fr.) noise signals was localized in air with the accuracy of 2-5 degrees +/- 0.02-0.4 degrees and of continuous broad band (1-20 kHz) noise, with the accuracy of 4.5 degrees +/- 0.2 degrees.

Acoustic development of a neonatal beluga whale (Delphinapterus leucas) at the John G. Shedd Aquarium

NASA Astrophysics Data System (ADS)

Carneiro, Brooke Elizabeth

Beluga whales (Delphinapterus leucas) were one of the first marine mammals to be in captivity and currently, nine zoological institutions in North America house belugas (Robeck et al., 2005). Despite their accessibility within these facilities, very little research has been done on the beluga whale that is related to their acoustic development or communication sounds. A male beluga calf named "Nunavik" was born at the John G. Shedd Aquarium on 14 December 2009, which provided an opportunity to examine the ontogeny of underwater sounds by a neonatal beluga from the birth throughout the first year of life. The objectives of the study were to: 1) collect underwater sound recordings of the beluga pod prior to the birth of the calf, 2) collect underwater sound recordings of the neonate during the first year of life, 3) document when and what types of sounds were produced by the calf, 4) compare sounds produced by the calf during agonistic and non-agonistic interactions, and 5) compare the acoustic features of sounds produced by the calf to sounds from the mother, a male beluga calf born at the Vancouver Aquarium in 2002, and other belugas at the John G. Shedd Aquarium. The first recordings of the beluga calf took place six hours following the birth for a two hour period. Subsequent recordings were made daily for one hour for the first two weeks of the calf's life and then twice per week until the calf was about six months of age. Later recordings were done less frequently; about once every other week, with no recordings during a 2-month period due to equipment failure. In total, sixty hours of underwater recordings of the belugas were collected from 26 September 2009 to 27 December 2010. Sounds were audibly and visually examined using Raven Pro version 1.4, a real-time sound analysis software application (Cornell Laboratory of Ornithology), and categorized into three categories (tones, noise, and noise with tones) based on the characteristics of underwater sounds from the same adult beluga whales recorded by Melissa Kelly (2009) at the John G. Shedd Aquarium in 2008. The first recorded sound produced by the calf was a low frequency, pulsed signal which was extremely weak in amplitude and almost seven times lower in frequency compared to similar sounds from a male beluga calf born at the Vancouver Aquarium in 2002. As he grew, the calf steadily increased the complexity and adult-like characteristics in all sound types. He decreased the peak frequency of tones, but increased the peak frequency of noise and noise with tones sounds. Using analysis of variance, sounds produced during the younger age class (0 to 6 months) were significantly longer in duration than during the older age class (6 to 12 months). There was no statistical difference in peak frequency of tones or tones with noise between the two age groups. The peak frequencies of both tones and tones with noise were significantly higher during agonistic contexts compared to non-agonistic contexts. Finally, the age at which the calf was first recorded using echolocation was at about five months. Future studies on the underwater acoustic behavior of beluga whale calves are necessary to identify developmental milestones in their repertoire.

Acoustic characteristics of the medium with gradient change of impedance

NASA Astrophysics Data System (ADS)

Hu, Bo; Yang, Desen; Sun, Yu; Shi, Jie; Shi, Shengguo; Zhang, Haoyang

2015-10-01

The medium with gradient change of acoustic impedance is a new acoustic structure which developed from multiple layer structures. In this paper, the inclusion is introduced and a new set of equations is developed. It can obtain better acoustic properties based on the medium with gradient change of acoustic impedance. Theoretical formulation has been systematically addressed which demonstrates how the idea of utilizing this method. The sound reflection and absorption coefficients were obtained. At last, the validity and the correctness of this method are assessed by simulations. The results show that appropriate design of parameters of the medium can improve underwater acoustic properties.

Design and Implementation of an Underwater Sound Recording Device

PubMed Central

Martinez, Jayson J.; Myers, Josh R.; Carlson, Thomas J.; Deng, Z. Daniel; Rohrer, John S.; Caviggia, Kurt A.; Woodley, Christa M.; Weiland, Mark A.

2011-01-01

To monitor the underwater sound and pressure waves generated by anthropogenic activities such as underwater blasting and pile driving, an autonomous system was designed to record underwater acoustic signals. The underwater sound recording device (USR) allows for connections of two hydrophones or other dynamic pressure sensors, filters high frequency noise out of the collected signals, has a gain that can be independently set for each sensor, and allows for 2 h of data collection. Two versions of the USR were created: a submersible model deployable to a maximum depth of 300 m, and a watertight but not fully submersible model. Tests were performed on the USR in the laboratory using a data acquisition system to send single-frequency sinusoidal voltages directly to each component. These tests verified that the device operates as designed and performs as well as larger commercially available data acquisition systems, which are not suited for field use. On average, the designed gain values differed from the actual measured gain values by about 0.35 dB. A prototype of the device was used in a case study to measure blast pressures while investigating the effect of underwater rock blasting on juvenile Chinook salmon and rainbow trout. In the case study, maximum positive pressure from the blast was found to be significantly correlated with frequency of injury for individual fish. The case study also demonstrated that the device withstood operation in harsh environments, making it a valuable tool for collecting field measurements. PMID:22164089

An underwater ranging system based on photoacoustic effect occurring on target surface

NASA Astrophysics Data System (ADS)

Ni, Kai; Hu, Kai; Li, Xinghui; Wang, Lidai; Zhou, Qian; Wang, Xiaohao

2016-11-01

In this paper, an underwater ranging system based on photoacoustic effect occurring on target surface is proposed. In this proposal, laser pulse generated by blue-green laser is directly incident on target surface, where the photoacoustic effect occurs and a sound source is formed. And then the sound wave which is also called photoacoustic signal is received by the ultrasonic receiver after passing through water. According to the time delay between transmitting laser and receiving photoacoustic signal, and sound velocity in water, the distance between the target and the ultrasonic receiver can be calculated. Differing from underwater range finding by only laser, this approach can avoid backscattering of laser beam, so easier to implement. Experimental system according to this principle has been constructed to verify the feasibility of this technology. The experimental results showed that a ranging accuracy of 1 mm can be effectively achieved when the target is close to the ultrasonic receiver.

The influence of acoustic emissions for underwater data transmission on the behaviour of harbour porpoises (Phocoena phocoena) in a floating pen.

PubMed

Kastelein, R A; Verboom, W C; Muijsers, M; Jennings, N V; van der Heul, S

2005-05-01

To prevent grounding of ships and collisions between ships in shallow coastal waters, an underwater data collection and communication network is currently under development: Acoustic Communication network for Monitoring of underwater Environment in coastal areas (ACME). Marine mammals might be affected by ACME sounds since they use sounds of similar frequencies (around 12 kHz) for communication, orientation, and prey location. If marine mammals tend to avoid the vicinity of the transmitters, they may be kept away from ecologically important areas by ACME sounds. One marine mammal species that may be affected in the North Sea is the harbour porpoise. Therefore, as part of an environmental impact assessment program, two captive harbour porpoises were subjected to four sounds, three of which may be used in the underwater acoustic data communication network. The effect of each sound was judged by comparing the animals' positions and respiration rates during a test period with those during a baseline period. Each of the four sounds could be made a deterrent by increasing the amplitude of the sound. The porpoises reacted by swimming away from the sounds and by slightly, but significantly, increasing their respiration rate. From the sound pressure level distribution in the pen, and the distribution of the animals during test sessions, discomfort sound level thresholds were determined for each sound. In combination with information on sound propagation in the areas where the communication system may be deployed, the extent of the 'discomfort zone' can be estimated for several source levels (SLs). The discomfort zone is defined as the area around a sound source that harbour porpoises are expected to avoid. Based on these results, SLs can be selected that have an acceptable effect on harbour porpoises in particular areas. The discomfort zone of a communication sound depends on the selected sound, the selected SL, and the propagation characteristics of the area in which the sound system is operational. In shallow, winding coastal water courses, with sandbanks, etc., the type of habitat in which the ACME sounds will be produced, propagation loss cannot be accurately estimated by using a simple propagation model, but should be measured on site. The SL of the communication system should be adapted to each area (taking into account bounding conditions created by narrow channels, sound propagation variability due to environmental factors, and the importance of an area to the affected species). The discomfort zone should not prevent harbour porpoises from spending sufficient time in ecologically important areas (for instance feeding areas), or routes towards these areas.

Characterization of Underwater Sounds Produced by Trailing Suction Hopper Dredges During Sand Mining and Pump-out Operations

DTIC Science & Technology

2014-03-01

origin and potential impacts on aquatic organisms including marine mammals (e.g., whales and seals), sea turtles , and fishes. Until recently these...species of whales and sea turtles , as well as many species of fish. Exposure to underwater sound may potentially affect communication, foraging...the audible range of several species of marine mammals such as whales and dolphins as well as sea turtles . Right (Eubalaena glacialis), humpback

Research in Distributed Underwater Acoustic Arrays.

DTIC Science & Technology

1980-04-01

Roth, "Effective Measurements Using Digital Signal Analysis," IEEE Spectrum, April 1971 . [14] R. J. Urick, Principlcs of Undcrwnter S nund, McGraw...April 1971 . [7] R. J. Urick, Principles of Underwater Sound, McGraw-Hill, New York, 1975. (8] D. J. Edelbluthe, J. M. Fisk and G. L. Kinnison...Flanagan, "Internal Tidal Influence on Deep-Ocean Acoustic-Ray Propagation," J. Acoust. Soc. Am., Vol. 56, No. 2, August 1971 . [10] C. N. K. Mooers, "Sound

Soundscapes and the sense of hearing of fishes.

PubMed

Fay, Richard

2009-03-01

Underwater soundscapes have probably played an important role in the adaptation of ears and auditory systems of fishes throughout evolutionary time, and for all species. These sounds probably contain important information about the environment and about most objects and events that confront the receiving fish so that appropriate behavior is possible. For example, the sounds from reefs appear to be used by at least some fishes for their orientation and migration. These sorts of environmental sounds should be considered much like "acoustic daylight," that continuously bathes all environments and contain information that all organisms can potentially use to form a sort of image of the environment. At present, however, we are generally ignorant of the nature of ambient sound fields impinging on fishes, and the adaptive value of processing these fields to resolve the multiple sources of sound. Our field has focused almost exclusively on the adaptive value of processing species-specific communication sounds, and has not considered the informational value of ambient "noise." Since all fishes can detect and process acoustic particle motion, including the directional characteristics of this motion, underwater sound fields are potentially more complex and information-rich than terrestrial acoustic environments. The capacities of one fish species (goldfish) to receive and make use of such sound source information have been demonstrated (sound source segregation and auditory scene analysis), and it is suggested that all vertebrate species have this capacity. A call is made to better understand underwater soundscapes, and the associated behaviors they determine in fishes. © 2009 ISZS, Blackwell Publishing and IOZ/CAS.

Mapping underwater sound noise and assessing its sources by using a self-organizing maps method.

PubMed

Rako, Nikolina; Vilibić, Ivica; Mihanović, Hrvoje

2013-03-01

This study aims to provide an objective mapping of the underwater noise and its sources over an Adriatic coastal marine habitat by applying the self-organizing maps (SOM) method. Systematic sampling of sea ambient noise (SAN) was carried out at ten predefined acoustic stations between 2007 and 2009. Analyses of noise levels were performed for 1/3 octave band standard centered frequencies in terms of instantaneous sound pressure levels averaged over 300 s to calculate the equivalent continuous sound pressure levels. Data on vessels' presence, type, and distance from the monitoring stations were also collected at each acoustic station during the acoustic sampling. Altogether 69 noise surveys were introduced to the SOM predefined 2 × 2 array. The overall results of the analysis distinguished two dominant underwater soundscapes, associating them mainly to the seasonal changes in the nautical tourism and fishing activities within the study area and to the wind and wave action. The analysis identified recreational vessels as the dominant anthropogenic source of underwater noise, particularly during the tourist season. The method demonstrated to be an efficient tool in predicting the SAN levels based on the vessel distribution, indicating also the possibility of its wider implication for marine conservation.

Predicting Anthropogenic Noise Contributions to US Waters.

PubMed

Gedamke, Jason; Ferguson, Megan; Harrison, Jolie; Hatch, Leila; Henderson, Laurel; Porter, Michael B; Southall, Brandon L; Van Parijs, Sofie

2016-01-01

To increase understanding of the potential effects of chronic underwater noise in US waters, the National Oceanic and Atmospheric Administration (NOAA) organized two working groups in 2011, collectively called "CetSound," to develop tools to map the density and distribution of cetaceans (CetMap) and predict the contribution of human activities to underwater noise (SoundMap). The SoundMap effort utilized data on density, distribution, acoustic signatures of dominant noise sources, and environmental descriptors to map estimated temporal, spatial, and spectral contributions to background noise. These predicted soundscapes are an initial step toward assessing chronic anthropogenic noise impacts on the ocean's varied acoustic habitats and the animals utilizing them.

75 FR 79342 - Taking and Importing Marine Mammals; Navy Training Activities Conducted Within the Northwest...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-20

...-frequency or high frequency active sonar (MFAS/HFAS) or to underwater detonations at levels that NMFS... exposing them to sound from mid-frequency or high frequency active sonar (MFAS/HFAS) or underwater...

Tracking marine mammals and ships with small and large-aperture hydrophone arrays

NASA Astrophysics Data System (ADS)

Gassmann, Martin

Techniques for passive acoustic tracking in all three spatial dimensions of marine mammals and ships were developed for long-term acoustic datasets recorded continuously over months using custom-designed arrays of underwater microphones (hydrophones) with spacing ranging from meters to kilometers. From the three-dimensional tracks, the acoustical properties of toothed whales and ships, such as sound intensity and directionality, were estimated as they are needed for the passive acoustic abundance estimation of toothed whales and for a quantitative description of the contribution of ships to the underwater soundscape. In addition, the tracks of the toothed whales reveal their underwater movements and demonstrate the potential of the developed tracking techniques to investigate their natural behavior and responses to sound generated by human activity, such as from ships or military SONAR. To track the periodically emitted echolocation sounds of toothed whales in an acoustically refractive environment in the upper ocean, a propagation-model based technique was developed for a hydrophone array consisting of one vertical and two L-shaped subarrays deployed from the floating instrument platform R/P FLIP. The technique is illustrated by tracking a group of five shallow-diving killer whales showing coordinated behavior. The challenge of tracking the highly directional echolocation sounds of deep-diving (< 1 km) toothed whales, in particular Cuvier's beaked whales, was addressed by embedding volumetric small-aperture (≈ 1 m element spacing) arrays into a large-aperture (≈ 1 km element spacing) seafloor array to reduce the minimum number of required receivers from five to two. The capabilities of this technique are illustrated by tracking several groups of up to three individuals over time periods from 10 min to 33 min within an area of 20 km2 in the Southern California Bight. To track and measure the underwater radiated sound of ships, a frequency domain beamformer was implemented for a volumetric hydrophone array (< 2 m element spacing) that was coupled to an autonomous acoustic seafloor recorder. This allows for the tracking and measurement of underwater radiated sound from ships of opportunity with a single instrument deployment and without depending on track information from the automatic information system (AIS).

Reef Sound as an Orientation Cue for Shoreward Migration by Pueruli of the Rock Lobster, Jasus edwardsii

PubMed Central

Green, Bridget S.; Gardner, Caleb; Hesse, Jan; Stanley, Jenni A.

2016-01-01

The post-larval or puerulus stage of spiny, or rock, lobsters (Palinuridae) swim many kilometres from open oceans into coastal waters where they subsequently settle. The orientation cues used by the puerulus for this migration are unclear, but are presumed to be critical to finding a place to settle. Understanding this process may help explain the biological processes of dispersal and settlement, and be useful for developing realistic dispersal models. In this study, we examined the use of reef sound as an orientation cue by the puerulus stage of the southern rock lobster, Jasus edwardsii. Experiments were conducted using in situ binary choice chambers together with replayed recording of underwater reef sound. The experiment was conducted in a sandy lagoon under varying wind conditions. A significant proportion of puerulus (69%) swam towards the reef sound in calm wind conditions. However, in windy conditions (>25 m s-1) the orientation behaviour appeared to be less consistent with the inclusion of these results, reducing the overall proportion of pueruli that swam towards the reef sound (59.3%). These results resolve previous speculation that underwater reef sound is used as an orientation cue in the shoreward migration of the puerulus of spiny lobsters, and suggest that sea surface winds may moderate the ability of migrating pueruli to use this cue to locate coastal reef habitat to settle. Underwater sound may increase the chance of successful settlement and survival of this valuable species. PMID:27310676

Reef Sound as an Orientation Cue for Shoreward Migration by Pueruli of the Rock Lobster, Jasus edwardsii.

PubMed

Hinojosa, Ivan A; Green, Bridget S; Gardner, Caleb; Hesse, Jan; Stanley, Jenni A; Jeffs, Andrew G

2016-01-01

The post-larval or puerulus stage of spiny, or rock, lobsters (Palinuridae) swim many kilometres from open oceans into coastal waters where they subsequently settle. The orientation cues used by the puerulus for this migration are unclear, but are presumed to be critical to finding a place to settle. Understanding this process may help explain the biological processes of dispersal and settlement, and be useful for developing realistic dispersal models. In this study, we examined the use of reef sound as an orientation cue by the puerulus stage of the southern rock lobster, Jasus edwardsii. Experiments were conducted using in situ binary choice chambers together with replayed recording of underwater reef sound. The experiment was conducted in a sandy lagoon under varying wind conditions. A significant proportion of puerulus (69%) swam towards the reef sound in calm wind conditions. However, in windy conditions (>25 m s-1) the orientation behaviour appeared to be less consistent with the inclusion of these results, reducing the overall proportion of pueruli that swam towards the reef sound (59.3%). These results resolve previous speculation that underwater reef sound is used as an orientation cue in the shoreward migration of the puerulus of spiny lobsters, and suggest that sea surface winds may moderate the ability of migrating pueruli to use this cue to locate coastal reef habitat to settle. Underwater sound may increase the chance of successful settlement and survival of this valuable species.

Drilling and operational sounds from an oil production island in the ice-covered Beaufort sea.

PubMed

Blackwell, Susanna B; Greene, Charles R; Richardson, W John

2004-11-01

Recordings of sounds underwater and in air, and of iceborne vibrations, were obtained at Northstar Island, an artificial gravel island in the Beaufort Sea near Prudhoe Bay (Alaska). The aim was to document the levels, characteristics, and range dependence of sounds and vibrations produced by drilling and oil production during the winter, when the island was surrounded by shore-fast ice. Drilling produced the highest underwater broadband (10-10,000 Hz) levels (maximum= 124 dB re: 1 microPa at 1 km), and mainly affected 700-1400 Hz frequencies. In contrast, drilling did not increase broadband levels in air or ice relative to levels during other island activities. Production did not increase broadband levels for any of the sensors. In all media, broadband levels decreased by approximately 20 dB/tenfold change in distance. Background levels underwater were reached by 9.4 km during drilling and 3-4 km without. In the air and ice, background levels were reached 5-10 km and 2-10 km from Northstar, respectively, depending on the wind but irrespective of drilling. A comparison of the recorded sounds with harbor and ringed seal audiograms showed that Northstar sounds were probably audible to seals, at least intermittently, out to approximately 1.5 km in water and approximately 5 km in air.

Low-frequency acoustic pressure, velocity, and intensity thresholds in a bottlenose dolphin (Tursiops truncatus) and white whale (Delphinapterus leucas)

NASA Astrophysics Data System (ADS)

Finneran, James J.; Carder, Donald A.; Ridgway, Sam H.

2002-01-01

The relative contributions of acoustic pressure and particle velocity to the low-frequency, underwater hearing abilities of the bottlenose dolphin (Tursiops truncatus) and white whale (Delphinapterus leucas) were investigated by measuring (masked) hearing thresholds while manipulating the relationship between the pressure and velocity. This was accomplished by varying the distance within the near field of a single underwater sound projector (experiment I) and using two underwater sound projectors and an active sound control system (experiment II). The results of experiment I showed no significant change in pressure thresholds as the distance between the subject and the sound source was changed. In contrast, velocity thresholds tended to increase and intensity thresholds tended to decrease as the source distance decreased. These data suggest that acoustic pressure is a better indicator of threshold, compared to particle velocity or mean active intensity, in the subjects tested. Interpretation of the results of experiment II (the active sound control system) was difficult because of complex acoustic conditions and the unknown effects of the subject on the generated acoustic field; however, these data also tend to support the results of experiment I and suggest that odontocete thresholds should be reported in units of acoustic pressure, rather than intensity.

Hydroacoustic pile driving noise study - comprehensive report : final report.

DOT National Transportation Integrated Search

2016-12-28

Alaska DOT&PF and JASCO Applied Sciences partnered to characterize underwater noise from pile driving activities to inform the assessment of the potential impact of such noise on marine mammals. JASCO measured underwater sounds at the Kake, Auke Bay,...

The influence of underwater data transmission sounds on the displacement behaviour of captive harbour seals (Phoca vitulina).

PubMed

Kastelein, Ronald A; van der Heul, Sander; Verboom, Willem C; Triesscheijn, Rob J V; Jennings, Nancy V

2006-02-01

To prevent grounding of ships and collisions between ships in shallow coastal waters, an underwater data collection and communication network (ACME) using underwater sounds to encode and transmit data is currently under development. Marine mammals might be affected by ACME sounds since they may use sound of a similar frequency (around 12 kHz) for communication, orientation, and prey location. If marine mammals tend to avoid the vicinity of the acoustic transmitters, they may be kept away from ecologically important areas by ACME sounds. One marine mammal species that may be affected in the North Sea is the harbour seal (Phoca vitulina). No information is available on the effects of ACME-like sounds on harbour seals, so this study was carried out as part of an environmental impact assessment program. Nine captive harbour seals were subjected to four sound types, three of which may be used in the underwater acoustic data communication network. The effect of each sound was judged by comparing the animals' location in a pool during test periods to that during baseline periods, during which no sound was produced. Each of the four sounds could be made into a deterrent by increasing its amplitude. The seals reacted by swimming away from the sound source. The sound pressure level (SPL) at the acoustic discomfort threshold was established for each of the four sounds. The acoustic discomfort threshold is defined as the boundary between the areas that the animals generally occupied during the transmission of the sounds and the areas that they generally did not enter during transmission. The SPLs at the acoustic discomfort thresholds were similar for each of the sounds (107 dB re 1 microPa). Based on this discomfort threshold SPL, discomfort zones at sea for several source levels (130-180 dB re 1 microPa) of the sounds were calculated, using a guideline sound propagation model for shallow water. The discomfort zone is defined as the area around a sound source that harbour seals are expected to avoid. The definition of the discomfort zone is based on behavioural discomfort, and does not necessarily coincide with the physical discomfort zone. Based on these results, source levels can be selected that have an acceptable effect on harbour seals in particular areas. The discomfort zone of a communication sound depends on the sound, the source level, and the propagation characteristics of the area in which the sound system is operational. The source level of the communication system should be adapted to each area (taking into account the width of a sea arm, the local sound propagation, and the importance of an area to the affected species). The discomfort zone should not coincide with ecologically important areas (for instance resting, breeding, suckling, and feeding areas), or routes between these areas.

Underwater superoleophobicity, anti-oil and ultra-broadband enhanced absorption of metallic surfaces produced by a femtosecond laser inspired by fish and chameleons

NASA Astrophysics Data System (ADS)

Yin, K.; Song, Y. X.; Dong, X. R.; Wang, C.; Duan, J. A.

2016-11-01

Reported here is the bio-inspired and robust function of underwater superoleophobic, anti-oil metallic surfaces with ultra-broadband enhanced optical absorption obtained through femtosecond laser micromachining. Three distinct surface structures are fabricated using a wide variety of processing parameters. Underwater superoleophobic and anti-oil surfaces containing coral-like microstructures with nanoparticles and mount-like microstructures are achieved. These properties of the as-prepared surfaces exhibit good chemical stability when exposed to various types of oils and when immersed in water with a wide range of pH values. Moreover, coral-like microstructures with nanoparticle surfaces show strongly enhanced optical absorption over a broadband wavelength range from 0.2-25 μm. The potential mechanism for the excellent performance of the coral-like microstructures with a nanoparticle surface is also discussed. This multifunctional surface has potential applications in military submarines, amphibious military aircraft and tanks, and underwater anti-oil optical counter-reconnaissance devices.

Acoustic effects of oil-production activities on bowhead and white whales visible during spring migration near Pt. Barrow, Alaska-1990 phase: sound propagation and whale responses to playbacks of continuous drilling noise from an ice platform, as studied in pack ice conditions. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richardson, W.J.; Greene, C.R.; Koski, W.R.

1991-10-01

The report concerns the effects of underwater noise from simulated oil production operations on the movements and behavior of bowhead and white whales migrating around northern Alaska in spring. An underwater sound projector suspended from pack ice was used to introduce recorded drilling noise and other test sounds into leads through the pack ice. These sounds were received and measured at various distances to determine the rate of sound attenuation with distance and frequency. The movements and behavior of bowhead and white whales approaching the operating projector were studied by aircraft- and ice-based observers. Some individuals of both species weremore » observed to approach well within the ensonified area. However, behavioral changes and avoidance reactions were evident when the received sound level became sufficiently high. Reactions to aircraft are also discussed.« less

Vocalisation Repertoire of Female Bluefin Gurnard (Chelidonichthys kumu) in Captivity: Sound Structure, Context and Vocal Activity.

PubMed

Radford, Craig A; Ghazali, Shahriman M; Montgomery, John C; Jeffs, Andrew G

2016-01-01

Fish vocalisation is often a major component of underwater soundscapes. Therefore, interpretation of these soundscapes requires an understanding of the vocalisation characteristics of common soniferous fish species. This study of captive female bluefin gurnard, Chelidonichthys kumu, aims to formally characterise their vocalisation sounds and daily pattern of sound production. Four types of sound were produced and characterised, twice as many as previously reported in this species. These sounds fit two aural categories; grunt and growl, the mean peak frequencies for which ranged between 129 to 215 Hz. This species vocalized throughout the 24 hour period at an average rate of (18.5 ± 2.0 sounds fish-1 h-1) with an increase in vocalization rate at dawn and dusk. Competitive feeding did not elevate vocalisation as has been found in other gurnard species. Bluefin gurnard are common in coastal waters of New Zealand, Australia and Japan and, given their vocalization rate, are likely to be significant contributors to ambient underwater soundscape in these areas.

Vocalisation Repertoire of Female Bluefin Gurnard (Chelidonichthys kumu) in Captivity: Sound Structure, Context and Vocal Activity

PubMed Central

Radford, Craig A.; Ghazali, Shahriman M.; Montgomery, John C.; Jeffs, Andrew G.

2016-01-01

Fish vocalisation is often a major component of underwater soundscapes. Therefore, interpretation of these soundscapes requires an understanding of the vocalisation characteristics of common soniferous fish species. This study of captive female bluefin gurnard, Chelidonichthys kumu, aims to formally characterise their vocalisation sounds and daily pattern of sound production. Four types of sound were produced and characterised, twice as many as previously reported in this species. These sounds fit two aural categories; grunt and growl, the mean peak frequencies for which ranged between 129 to 215 Hz. This species vocalized throughout the 24 hour period at an average rate of (18.5 ± 2.0 sounds fish-1 h-1) with an increase in vocalization rate at dawn and dusk. Competitive feeding did not elevate vocalisation as has been found in other gurnard species. Bluefin gurnard are common in coastal waters of New Zealand, Australia and Japan and, given their vocalization rate, are likely to be significant contributors to ambient underwater soundscape in these areas. PMID:26890124

Quantifying the Effects of Propagation on Classification of Cetacean Vocalizations

DTIC Science & Technology

2015-09-30

mammals can be found in all ocean basins, their habitats cover diverse underwater environments. It is well known that acoustic propagation can vary...propagation on an automated classifier, using both underwater propagation experiments and complementary modeling. If propagation does impact some... Underwater Sound, 3rd ed., McGraw-Hill Book Company, 1983. [2] F. B. Jensen, W. A. Kuperman, M.B. Porter, and H. Schmidt, Computational Ocean Acoustics

Underwater sound transmission through arrays of disk cavities in a soft elastic medium.

PubMed

Calvo, David C; Thangawng, Abel L; Layman, Christopher N; Casalini, Riccardo; Othman, Shadi F

2015-10-01

Scattering from a cavity in a soft elastic medium, such as silicone rubber, resembles scattering from an underwater bubble in that low-frequency monopole resonance is obtainable in both cases. Arrays of cavities can therefore be used to reduce underwater sound transmission using thin layers and low void fractions. This article examines the role of cavity shape by microfabricating arrays of disk-shaped air cavities into single and multiple layers of polydimethylsiloxane. Comparison is made with the case of equivalent volume cylinders which approximate spheres. Measurements of ultrasonic underwater sound transmission are compared with finite element modeling predictions. The disks provide a deeper transmission minimum at a lower frequency owing to the drum-type breathing resonance. The resonance of a single disk cavity in an unbounded medium is also calculated and compared with a derived estimate of the natural frequency of the drum mode. Variation of transmission is determined as a function of disk tilt angle, lattice constant, and layer thickness. A modeled transmission loss of 18 dB can be obtained at a wavelength about 20 times the three-layer thickness, and thinner results (wavelength/thickness ∼ 240) are possible for the same loss with a single layer depending on allowable hydrostatic pressure.

Experimental findings on the underwater measurements uncertainty of speed of sound and the alignment system

NASA Astrophysics Data System (ADS)

Santos, T. Q.; Alvarenga, A. V.; Oliveira, D. P.; Mayworm, R. C.; Souza, R. M.; Costa-Félix, R. P. B.

2016-07-01

Speed of sound is an important quantity to characterize reference materials for ultrasonic applications, for instance. The alignment between the transducer and the test body is an key activity in order to perform reliable and consistent measurement. The aim of this work is to evaluate the influence of the alignment system to the expanded uncertainty of such measurement. A stainless steel cylinder was previously calibrated on an out of water system typically used for calibration of non-destructive blocks. Afterwards, the cylinder was calibrated underwater with two distinct alignment system: fixed and mobile. The values were statistically compared to the out-of-water measurement, considered the golden standard for such application. For both alignment systems, the normalized error was less than 0.8, leading to conclude that the both measurement system (under and out-of-water) do not diverge significantly. The gold standard uncertainty was 2.7 m-s-1, whilst the fixed underwater system resulted in 13 m-s-1, and the mobile alignment system achieved 6.6 m-s-1. After the validation of the underwater system for speed of sound measurement, it will be applied to certify Encapsulated Tissue Mimicking Material as a reference material for biotechnology application.

Channel analysis for single photon underwater free space quantum key distribution.

PubMed

Shi, Peng; Zhao, Shi-Cheng; Gu, Yong-Jian; Li, Wen-Dong

2015-03-01

We investigate the optical absorption and scattering properties of underwater media pertinent to our underwater free space quantum key distribution (QKD) channel model. With the vector radiative transfer theory and Monte Carlo method, we obtain the attenuation of photons, the fidelity of the scattered photons, the quantum bit error rate, and the sifted key generation rate of underwater quantum communication. It can be observed from our simulations that the most secure single photon underwater free space QKD is feasible in the clearest ocean water.

Fish Hearing.

ERIC Educational Resources Information Center

Blaxter, J. H. S.

1980-01-01

Provides related information about hearing in fish, including the sensory stimulus of sound in the underwater environment, mechanoreceptors in fish, pressure perception and the swimbladder, specializations in sound conduction peculiar to certain fish families. Includes numerous figures. (CS)

Metasurface for Water-to-Air Sound Transmission

NASA Astrophysics Data System (ADS)

Bok, Eun; Park, Jong Jin; Choi, Haejin; Han, Chung Kyu; Wright, Oliver B.; Lee, Sam H.

2018-01-01

Effective transmission of sound from water to air is crucial for the enhancement of the detection sensitivity of underwater sound. However, only 0.1% of the acoustic energy is naturally transmitted at such a boundary. At audio frequencies, quarter-wave plates or multilayered antireflection coatings are too bulky for practical use for such enhancement. Here we present an acoustic metasurface of a thickness of only ˜λ /100 , where λ is the wavelength in air, consisting of an array of meta-atoms that each contain a set of membranes and an air-filled cavity. We experimentally demonstrate that such a meta-atom increases the transmission of sound at ˜700 Hz by 2 orders of magnitude, allowing about 30% of the incident acoustic power from water to be transmitted into air. Applications include underwater sonic sensing and communication.

Design and implementation of an underwater sound recording device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, Jayson J.; Myers, Joshua R.; Carlson, Thomas J.

2011-09-01

To monitor the underwater sound and pressure waves generated by activities such as underwater blasting and pile driving, an autonomous system used to record underwater acoustic signals was designed. The device designed allows two hydrophones or other dynamic pressure sensors to be connected, filters out high frequency noise, has a gain that can be independently set for each sensor, and allows two hours of data to be collected. Two versions of the USR were created; one is submersible to a maximum depth of 300 m, and the other, although watertight, is not intended to be fully submersed. Tests were performedmore » in the laboratory using a data acquisition system to send single-frequency sinusoidal voltages directly to the each component. These tests verified that the device performs as well as larger commercially available data acquisition systems, which are not suited for field use. A prototype of the device was used in a case study to investigate the effect of underwater rock blasting on juvenile Chinook salmon and rainbow trout. The case study demonstrated that the device was able to tolerate being operated in harsh environments, making it a valuable tool for collecting field measurements.« less

Use of baited remote underwater video (BRUV) and motion analysis for studying the impacts of underwater noise upon free ranging fish and implications for marine energy management.

PubMed

Roberts, Louise; Pérez-Domínguez, Rafael; Elliott, Michael

2016-11-15

Free-ranging individual fish were observed using a baited remote underwater video (BRUV) system during sound playback experiments. This paper reports on test trials exploring BRUV design parameters, image analysis and practical experimental designs. Three marine species were exposed to playback noise, provided as examples of behavioural responses to impulsive sound at 163-171dB re 1μPa (peak-to-peak SPL) and continuous sound of 142.7dB re 1μPa (RMS, SPL), exhibiting directional changes and accelerations. The methods described here indicate the efficacy of BRUV to examine behaviour of free-ranging species to noise playback, rather than using confinement. Given the increasing concern about the effects of water-borne noise, for example its inclusion within the EU Marine Strategy Framework Directive, and the lack of empirical evidence in setting thresholds, this paper discusses the use of BRUV, and short term behavioural changes, in supporting population level marine noise management. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermal management of thermoacoustic sound projectors using a free-standing carbon nanotube aerogel sheet as a heat source.

PubMed

Aliev, Ali E; Mayo, Nathanael K; Baughman, Ray H; Avirovik, Dragan; Priya, Shashank; Zarnetske, Michael R; Blottman, John B

2014-10-10

Carbon nanotube (CNT) aerogel sheets produce smooth-spectra sound over a wide frequency range (1-10(5) Hz) by means of thermoacoustic (TA) sound generation. Protective encapsulation of CNT sheets in inert gases between rigid vibrating plates provides resonant features for the TA sound projector and attractive performance at needed low frequencies. Energy conversion efficiencies in air of 2% and 10% underwater, which can be enhanced by further increasing the modulation temperature. Using a developed method for accurate temperature measurements for the thin aerogel CNT sheets, heat dissipation processes, failure mechanisms, and associated power densities are investigated for encapsulated multilayered CNT TA heaters and related to the thermal diffusivity distance when sheet layers are separated. Resulting thermal management methods for high applied power are discussed and deployed to construct efficient and tunable underwater sound projector for operation at relatively low frequencies, 10 Hz-10 kHz. The optimal design of these TA projectors for high-power SONAR arrays is discussed.

Quantum imaging for underwater arctic navigation

NASA Astrophysics Data System (ADS)

Lanzagorta, Marco

2017-05-01

The precise navigation of underwater vehicles is a difficult task due to the challenges imposed by the variable oceanic environment. It is particularly difficult if the underwater vehicle is trying to navigate under the Arctic ice shelf. Indeed, in this scenario traditional navigation devices such as GPS, compasses and gyrocompasses are unavailable or unreliable. In addition, the shape and thickness of the ice shelf is variable throughout the year. Current Arctic underwater navigation systems include sonar arrays to detect the proximity to the ice. However, these systems are undesirable in a wartime environment, as the sound gives away the position of the underwater vehicle. In this paper we briefly describe the theoretical design of a quantum imaging system that could allow the safe and stealthy navigation of underwater Arctic vehicles.

Anthropogenic sources of underwater sound can modify how sediment-dwelling invertebrates mediate ecosystem properties

PubMed Central

Solan, Martin; Hauton, Chris; Godbold, Jasmin A.; Wood, Christina L.; Leighton, Timothy G.; White, Paul

2016-01-01

Coastal and shelf environments support high levels of biodiversity that are vital in mediating ecosystem processes, but they are also subject to noise associated with mounting levels of offshore human activity. This has the potential to alter the way in which species interact with their environment, compromising the mediation of important ecosystem properties. Here, we show that exposure to underwater broadband sound fields that resemble offshore shipping and construction activity can alter sediment-dwelling invertebrate contributions to fluid and particle transport - key processes in mediating benthic nutrient cycling. Despite high levels of intra-specific variability in physiological response, we find that changes in the behaviour of some functionally important species can be dependent on the class of broadband sound (continuous or impulsive). Our study provides evidence that exposing coastal environments to anthropogenic sound fields is likely to have much wider ecosystem consequences than are presently acknowledged. PMID:26847483

Distress sounds of thorny catfishes emitted underwater and in air: characteristics and potential significance.

PubMed

Knight, Lisa; Ladich, Friedrich

2014-11-15

Thorny catfishes produce stridulation (SR) sounds using their pectoral fins and drumming (DR) sounds via a swimbladder mechanism in distress situations when hand held in water and in air. It has been argued that SR and DR sounds are aimed at different receivers (predators) in different media. The aim of this study was to analyse and compare sounds emitted in both air and water in order to test different hypotheses on the functional significance of distress sounds. Five representatives of the family Doradidae were investigated. Fish were hand held and sounds emitted in air and underwater were recorded (number of sounds, sound duration, dominant and fundamental frequency, sound pressure level and peak-to-peak amplitudes). All species produced SR sounds in both media, but DR sounds could not be recorded in air for two species. Differences in sound characteristics between media were small and mainly limited to spectral differences in SR. The number of sounds emitted decreased over time, whereas the duration of SR sounds increased. The dominant frequency of SR and the fundamental frequency of DR decreased and sound pressure level of SR increased with body size across species. The hypothesis that catfish produce more SR sounds in air and more DR sounds in water as a result of different predation pressure (birds versus fish) could not be confirmed. It is assumed that SR sounds serve as distress sounds in both media, whereas DR sounds might primarily be used as intraspecific communication signals in water in species possessing both mechanisms. © 2014. Published by The Company of Biologists Ltd.

Equations for normal-mode statistics of sound scattering by a rough elastic boundary in an underwater waveguide, including backscattering.

PubMed

Morozov, Andrey K; Colosi, John A

2017-09-01

Underwater sound scattering by a rough sea surface, ice, or a rough elastic bottom is studied. The study includes both the scattering from the rough boundary and the elastic effects in the solid layer. A coupled mode matrix is approximated by a linear function of one random perturbation parameter such as the ice-thickness or a perturbation of the surface position. A full two-way coupled mode solution is used to derive the stochastic differential equation for the second order statistics in a Markov approximation.

Interpreting Underwater Acoustic Images of the Upper Ocean Boundary Layer

ERIC Educational Resources Information Center

Ulloa, Marco J.

2007-01-01

A challenging task in physical studies of the upper ocean using underwater sound is the interpretation of high-resolution acoustic images. This paper covers a number of basic concepts necessary for undergraduate and postgraduate students to identify the most distinctive features of the images, providing a link with the acoustic signatures of…

Minimizing noise in fiberglass aquaculture tanks: Noise reduction potential of various retrofits

USDA-ARS?s Scientific Manuscript database

Equipment used in intensive aquaculture systems, such as pumps and blowers can produce underwater sound levels and frequencies within the range of fish hearing. The impacts of underwater noise on fish are not well known, but limited research suggests that subjecting fish to noise could result in imp...

Characterizing large river sounds: Providing context for understanding the environmental effects of noise produced by hydrokinetic turbines

DOE PAGES

Bevelhimer, Mark S.; Deng, Z. Daniel; Scherelis, Constantin C.

2016-01-06

Underwaternoise associated with the installation and operation of hydrokinetic turbines in rivers and tidal zones presents a potential environmental concern for fish and marine mammals. Comparing the spectral quality of sounds emitted by hydrokinetic turbines to natural and other anthropogenic sound sources is an initial step at understanding potential environmental impacts. Underwater recordings were obtained from passing vessels and natural underwater sound sources in static and flowing waters. Static water measurements were taken in a lake with minimal background noise. Flowing water measurements were taken at a previously proposed deployment site for hydrokinetic turbines on the Mississippi River, where soundsmore » created by flowing water are part of all measurements, both natural ambient and anthropogenic sources. Vessel sizes ranged from a small fishing boat with 60 hp outboard motor to an 18-unit barge train being pushed upstream by tugboat. As expected, large vessels with large engines created the highest sound levels, which were, on average, 40 dB greater than the sound created by an operating hydrokinetic turbine. As a result, a comparison of sound levels from the same sources at different distances using both spherical and cylindrical sound attenuation functions suggests that spherical model results more closely approximate observed sound attenuation.« less

Validation of trophic and anthropic underwater noise as settlement trigger in blue mussels

NASA Astrophysics Data System (ADS)

Jolivet, Aurélie; Tremblay, Rejean; Olivier, Fréderic; Gervaise, Cédric; Sonier, Rémi; Genard, Bertrand; Chauvaud, Laurent

2016-09-01

Like the majority of benthic invertebrates, the blue mussel Mytilus edulis has a bentho-pelagic cycle with its larval settlement being a complex phenomenon involving numerous factors. Among these factors, underwater noise and pelagic trophic conditions have been weakly studied in previous researches. Under laboratory conditions, we tested the hypothesis that picoplankton assimilation by the pediveliger blue mussel larvae acts as a food cue that interacts with anthropic underwater sound to stimulate settlement. We used 13C-labeling microalgae to validate the assimilation of different picoplankton species in the tissues of pediveliger larvae. Our results clearly confirm our hypothesis with a significant synergic effect of these two factors. However, only the picoeukaryotes strains assimilated by larvae stimulated the settlement, whereas the non-ingested picocyanobacteria did not. Similar positive responses were observed with underwater sound characterized by low frequency vessel noises. The combination of both factors (trophic and vessel noise) drastically increased the mussel settlement by an order of 4 compared to the control (without picoplankton and noise). Settlement levels ranged from 16.5 to 67% in 67 h.

Functional morphology of the inner ear and underwater audiograms of Proteus anguinus (Amphibia, Urodela).

PubMed

Bulog, B; Schlegel, P

2000-01-01

Octavolateral sensory organs (auditory and lateral line organs) of cave salamander Proteus anguinus are highly differentiated. In the saccular macula of the inner ear the complex pattern of hair cell orientation and the large otoconial mass enable particle displacement direction detection. Additionally, the same organ, through air cavities within the body, enables detection of underwater sound pressure changes thus acting as a hearing organ. The cavities in the lungs and mouth of Proteus are a resonators that transmit underwater sound pressure to the inner ear. Behaviourally determined audiograms indicate hearing sensitivity of 60 dB (rel. 1 microPa) at frequencies between 1 and 10 kHz. The hearing frequency range was between 10 Hz and 10 kHz. The hearing sensitivities of depigmented Proteus and black Proteus were compared. The highest sensitivities of the depigmented animals (N=4) were at frequencies 1.3-1.7 kHz and it was 2 kHz in black animals (N=1). Excellent underwater hearing abilities of Proteus are sensory adaptations to cave habitat.

Comparative assessment of amphibious hearing in pinnipeds.

PubMed

Reichmuth, Colleen; Holt, Marla M; Mulsow, Jason; Sills, Jillian M; Southall, Brandon L

2013-06-01

Auditory sensitivity in pinnipeds is influenced by the need to balance efficient sound detection in two vastly different physical environments. Previous comparisons between aerial and underwater hearing capabilities have considered media-dependent differences relative to auditory anatomy, acoustic communication, ecology, and amphibious life history. New data for several species, including recently published audiograms and previously unreported measurements obtained in quiet conditions, necessitate a re-evaluation of amphibious hearing in pinnipeds. Several findings related to underwater hearing are consistent with earlier assessments, including an expanded frequency range of best hearing in true seals that spans at least six octaves. The most notable new results indicate markedly better aerial sensitivity in two seals (Phoca vitulina and Mirounga angustirostris) and one sea lion (Zalophus californianus), likely attributable to improved ambient noise control in test enclosures. An updated comparative analysis alters conventional views and demonstrates that these amphibious pinnipeds have not necessarily sacrificed aerial hearing capabilities in favor of enhanced underwater sound reception. Despite possessing underwater hearing that is nearly as sensitive as fully aquatic cetaceans and sirenians, many seals and sea lions have retained acute aerial hearing capabilities rivaling those of terrestrial carnivores.

Measurement and characterisation of radiated underwater sound from a 3.6 MW monopile wind turbine.

PubMed

Pangerc, Tanja; Theobald, Peter D; Wang, Lian S; Robinson, Stephen P; Lepper, Paul A

2016-10-01

This paper describes underwater sound pressure measurements obtained in close proximity (∼50 m) to two individual wind turbines, over a 21-day period, capturing the full range of turbine operating conditions. The sound radiated into the water was characterised by a number of tonal components, which are thought to primarily originate from the gearbox for the bandwidth measured. The main signal associated with the turbine operation had a mean-square sound pressure spectral density level which peaked at 126 dB re 1 μPa 2  Hz -1 at 162 Hz. Other tonal components were also present, notably at frequencies between about 20 and 330 Hz, albeit at lower amplitudes. The measured sound characteristics, both in terms of frequency and amplitude, were shown to vary with wind speed. The sound pressure level increased with wind speed up to an average value of 128 dB re 1 μPa at a wind speed of about 10 ms -1 , and then showed a general decrease. Overall, differences in the mean-square sound pressure spectral density level of over 20 dB were observed across the operational envelope of the turbine.

Sound transmission in archaic and modern whales: anatomical adaptations for underwater hearing.

PubMed

Nummela, Sirpa; Thewissen, J G M; Bajpai, Sunil; Hussain, Taseer; Kumar, Kishor

2007-06-01

The whale ear, initially designed for hearing in air, became adapted for hearing underwater in less than ten million years of evolution. This study describes the evolution of underwater hearing in cetaceans, focusing on changes in sound transmission mechanisms. Measurements were made on 60 fossils of whole or partial skulls, isolated tympanics, middle ear ossicles, and mandibles from all six archaeocete families. Fossil data were compared with data on two families of modern mysticete whales and nine families of modern odontocete cetaceans, as well as five families of noncetacean mammals. Results show that the outer ear pinna and external auditory meatus were functionally replaced by the mandible and the mandibular fat pad, which posteriorly contacts the tympanic plate, the lateral wall of the bulla. Changes in the ear include thickening of the tympanic bulla medially, isolation of the tympanoperiotic complex by means of air sinuses, functional replacement of the tympanic membrane by a bony plate, and changes in ossicle shapes and orientation. Pakicetids, the earliest archaeocetes, had a land mammal ear for hearing in air, and used bone conduction underwater, aided by the heavy tympanic bulla. Remingtonocetids and protocetids were the first to display a genuine underwater ear where sound reached the inner ear through the mandibular fat pad, the tympanic plate, and the middle ear ossicles. Basilosaurids and dorudontids showed further aquatic adaptations of the ossicular chain and the acoustic isolation of the ear complex from the skull. The land mammal ear and the generalized modern whale ear are evolutionarily stable configurations, two ends of a process where the cetacean mandible might have been a keystone character. 2007 Wiley-Liss, Inc.

Auditory Sensitivity and Masking Profiles for the Sea Otter (Enhydra lutris).

PubMed

Ghoul, Asila; Reichmuth, Colleen

2016-01-01

Sea otters are threatened marine mammals that may be negatively impacted by human-generated coastal noise, yet information about sound reception in this species is surprisingly scarce. We investigated amphibious hearing in sea otters by obtaining the first measurements of absolute sensitivity and critical masking ratios. Auditory thresholds were measured in air and underwater from 0.125 to 40 kHz. Critical ratios derived from aerial masked thresholds from 0.25 to 22.6 kHz were also obtained. These data indicate that although sea otters can detect underwater sounds, their hearing appears to be primarily air adapted and not specialized for detecting signals in background noise.

Shallow Water Bathymetry using the REMUS 100 Autonomous Underwater Vehicle

DTIC Science & Technology

2013-12-01

potentially meeting IHO Standards for Hydrographic Surveys, are advertised but Kongsberg Hydroid do not recommend the REMUS 100 as a platform for...data set. Outlier soundings due to measurement errors have been discarded Figure 28: REMUS 100 depth soundings in isometric projection, coloured

The impact of glacier meltwater on the underwater noise field in a glacial bay

NASA Astrophysics Data System (ADS)

Glowacki, Oskar; Moskalik, Mateusz; Deane, Grant B.

2016-12-01

Ambient noise oceanography is proving to be an efficient and effective tool for the study of ice-ocean interactions in the bays of marine-terminating glaciers. However, obtaining quantitative estimates of ice melting or calving processes from ambient noise requires an understanding of how sound propagation through the bay attenuates and filters the noise spectrum. Measurements of the vertical structure in sound speed in the vicinity of the Hans Glacier in Hornsund Fjord, Spitsbergen, made with O(130) CTD casts between May and November 2015, reveal high-gradient, upward-refracting sound speed profiles created by cold, fresh meltwater during summer months. Simultaneous recordings of underwater ambient noise made at depths of 1, 10, and 20 m in combination with propagation model calculations using the model Bellhop illustrate the dominant role these surface ducts play in shaping the underwater soundscape. The surface ducts lead to a higher intensity and greater variability of acoustic energy in the near-surface layer covered by glacially modified waters relative to deeper waters, indicating deeper zones as most appropriate for interseasonal acoustic monitoring of the glacial melt. Surface waveguides in Hornsund are relatively shallow and trap sound above O(1 kHz). Deeper waveguides observed elsewhere will also trap low-frequency sounds, such as those generated by calving events for example. Finally, the ambient noise field in Hornsund is shown to be strongly dependent on the distribution of ice throughout the bay, stressing the importance of performing complementary environmental measurements when interpreting the results of acoustic surveys.

Sound absorption of metallic sound absorbers fabricated via the selective laser melting process

NASA Astrophysics Data System (ADS)

Cheng, Li-Wei; Cheng, Chung-Wei; Chung, Kuo-Chun; Kam, Tai-Yan

2017-01-01

The sound absorption capability of metallic sound absorbers fabricated using the additive manufacturing (selective laser melting) method is investigated via both the experimental and theoretical approaches. The metallic sound absorption structures composed of periodic cubic cells were made of laser-melted Ti6Al4 V powder. The acoustic impedance equations with different frequency-independent and frequency-dependent end corrections factors are employed to calculate the theoretical sound absorption coefficients of the metallic sound absorption structures. The calculated sound absorption coefficients are in close agreement with the experimental results for the frequencies ranging from 2 to 13 kHz.

Is the Venice Lagoon Noisy? First Passive Listening Monitoring of the Venice Lagoon: Possible Effects on the Typical Fish Community.

PubMed

Bolgan, Marta; Picciulin, Marta; Codarin, Antonio; Fiorin, Riccardo; Zucchetta, Matteo; Malavasi, Stefano

2016-01-01

Three passive listening surveys have been carried out in two of the three Venice lagoon tide inlets and inside the Venice island. The spectral content and the intensity level of the underwater noise as well as the presence or absence of Sciaena umbra and the distribution of its different sound patterns have been investigated in all the recording sites. The passive listening proved to be successful in detecting S. umbra drumming sounds in both Venice lagoon tide inlets. Our results indicate that the spectral content and the level of underwater noise pollution in the Venice lagoon could affect fish acoustic communication.

NRL Fact Book

DTIC Science & Technology

1978-01-01

Environmental Studies Geophysical and bathymetric mea- surements taken in the NRL Arctic program from 1971 through 1975 have been combined with...instrumented for investigating acoustic echo characteristics of targets Tank 9.1 m (30 ft) in diameter by 6.7-m (22-ft) deep for precise studies of...34 Underwater Sound Reference Division (Orlando, FL) 2.8-hectare (7-acre) lake with a large pier and instrumentation for underwater acoustic studies

Dynamics and Stability of Acoustic Wavefronts in the Ocean

DTIC Science & Technology

2014-09-30

processes on underwater acoustic fields. The 3-D HWT algorithm was also applied to investigate long- range propagation of infrasound in the atmosphere...oceanographic processes on underwater sound propagation and also has been demonstrated to be an efficient and robust technique for modeling infrasound ...algorithm by modeling propagation of infrasound generated by Eyjafjallajökull volcano in southern Iceland. Eruptions of this volcano were recorded by

Underwater sound pressure variation and bottlenose dolphin (Tursiops truncatus) hearing thresholds in a small pool.

PubMed

Finneran, James J; Schlundt, Carolyn E

2007-07-01

Studies of underwater hearing are often hampered by the behavior of sound waves in small experimental tanks. At lower frequencies, tank dimensions are often not sufficient for free field conditions, resulting in large spatial variations of sound pressure. These effects may be mitigated somewhat by increasing the frequency bandwidth of the sound stimulus, so effects of multipath interference average out over many frequencies. In this study, acoustic fields and bottlenose dolphin (Tursiops truncatus) hearing thresholds were compared for pure tone and frequency modulated signals. Experiments were conducted in a vinyl-walled, seawater-filled pool approximately 3.7 x 6 x 1.5 m. Acoustic signals were pure tone and linear and sinusoidal frequency modulated tones with bandwidths/modulation depths of 1%, 2%, 5%, 10%, and 20%. Thirteen center frequencies were tested between 1 and 100 kHz. Acoustic fields were measured (without the dolphin present) at three water depths over a 60 x 65 cm grid with a 5-cm spacing. Hearing thresholds were measured using a behavioral response paradigm and up/down staircase technique. The use of FM signals significantly improved the sound field without substantially affecting the measured hearing thresholds.

Acoustical deterrence of Silver Carp (Hypophthalmichthys molitrix)

USGS Publications Warehouse

Brooke J. Vetter,; Cupp, Aaron R.; Fredricks, Kim T.; Gaikowski, Mark P.; Allen F. Mensinger,

2015-01-01

The invasive Silver Carp (Hypophthalmichthys molitrix) dominate large regions of the Mississippi River drainage and continue to expand their range northward threatening the Laurentian Great Lakes. This study found that complex broadband sound (0–10 kHz) is effective in altering the behavior of Silver Carp with implications for deterrent barriers or potential control measures (e.g., herding fish into nets). The phonotaxic response of Silver Carp was investigated using controlled experiments in outdoor concrete ponds (10 × 4.9 × 1.2 m). Pure tones (500–2000 Hz) and complex sound (underwater field recordings of outboard motors) were broadcast using underwater speakers. Silver Carp always reacted to the complex sounds by exhibiting negative phonotaxis to the sound source and by alternating speaker location, Silver Carp could be directed consistently, up to 37 consecutive times, to opposite ends of the large outdoor pond. However, fish habituated quickly to pure tones, reacting to only approximately 5 % of these presentations and never showed more than two consecutive responses. Previous studies have demonstrated the success of sound barriers in preventing Silver Carp movement using pure tones and this research suggests that a complex sound stimulus would be an even more effective deterrent.

BIAS: A Regional Management of Underwater Sound in the Baltic Sea.

PubMed

Sigray, Peter; Andersson, Mathias; Pajala, Jukka; Laanearu, Janek; Klauson, Aleksander; Tegowski, Jaroslaw; Boethling, Maria; Fischer, Jens; Tougaard, Jakob; Wahlberg, Magnus; Nikolopoulos, Anna; Folegot, Thomas; Matuschek, Rainer; Verfuss, Ursula

2016-01-01

Management of the impact of underwater sound is an emerging concern worldwide. Several countries are in the process of implementing regulatory legislations. In Europe, the Marine Strategy Framework Directive was launched in 2008. This framework addresses noise impacts and the recommendation is to deal with it on a regional level. The Baltic Sea is a semienclosed area with nine states bordering the sea. The number of ships is one of the highest in Europe. Furthermore, the number of ships is estimated to double by 2030. Undoubtedly, due to the unbound character of noise, an efficient management of sound in the Baltic Sea must be done on a regional scale. In line with the European Union directive, the Baltic Sea Information on the Acoustic Soundscape (BIAS) project was established to implement Descriptor 11 of the Marine Strategy Framework Directive in the Baltic Sea region. BIAS will develop tools, standards, and methodologies that will allow for cross-border handling of data and results, measure sound in 40 locations for 1 year, establish a seasonal soundscape map by combining measured sound with advanced three-dimensional modeling, and, finally, establish standards for measuring continuous sound. Results from the first phase of BIAS are presented here, with an emphasis on standards and soundscape mapping as well as the challenges related to regional handling.

Underwater audiogram of the California sea lion by the conditioned vocalization technique1

PubMed Central

Schusterman, Ronald J.; Balliet, Richard F.; Nixon, James

1972-01-01

Conditioning techniques were developed demonstrating that pure tone frequencies under water can exert nearly perfect control over the underwater click vocalizations of the California sea lion (Zalophus californianus). Conditioned vocalizations proved to be a reliable way of obtaining underwater sound detection thresholds in Zalophus at 13 different frequencies, covering a frequency range of 250 to 64,000 Hz. The audiogram generated by these threshold measurements suggests that under water, the range of maximal sensitivity for Zalophus lies between one and 28 kHz with best sensitivity at 16 kHz. Between 28 and 36 kHz there is a loss in sensitivity of 60 dB/octave. However, with relatively intense acoustic signals (> 38 dB re 1 μb underwater), Zalophus will respond to frequencies at least as high as 192 kHz. These results are compared with the underwater hearing of other marine mammals. ImagesFig. 1. PMID:5033891

Hemispherical Optical Dome for Underwater Communication

NASA Technical Reports Server (NTRS)

Shiri, Ron S.; Lunde, Emily L.; Coronado, Patrick L.; Quijada, Manuel A.

2017-01-01

For many years, acoustic systems have been used as the primary method for underwater communication; however, the data transfer rate of such systems is low because sound propagates slowly through the water. A higher throughput can be achieved using visible light to transmit data underwater. The first issue with using this approach is that there is generally a large loss of the light signal due to scattering and absorption in water even though there is an optimal wavelength for transmission in the blue or green wavelengths of the visible spectrum. The second issue is that a simple system consisting only of a highly directional source transmitter and small optical detector receiver has a very narrow field of view. The goal of this project is to improve an optical, underwater communication system by increasing the effective field of view of the receiving optics. To this end, we make two changes to the simple system: (1) An optical dome was added near the receiver. An array of lenses is placed radially on the surface of the dome, reminiscent of the compound eye of an insect. The lenses make the source and detector planes conjugate, and each lens adds a new region of the source plane to the instrument's total field of view. (2) The receiver was expanded to include multiple photodiodes. With these two changes, the receiver has much more tolerance to misalignments (in position and angle) of the transmitter.Two versions of the optical dome (with 6 and 8 diameters) were designed using the CREO CAD software and modeled using the CODE V optical design software. A series of these transparent hemispherical domes, with both design diameters, were manufactured using a 5-axis mill. The prototype was then retrofitted with lenses and compared with the computer-generated model to demonstrate the effectiveness of this solution. This work shows the dome design improves the optical field of view of the underwater communication system considerably. Furthermore, with the experimental test results, a geometric optimization model was derived providing insights to the design performance limits.

Hemispherical optical dome for underwater communication

NASA Astrophysics Data System (ADS)

Shiri, Ron S.; Lunde, Emily L.; Coronado, Patrick L.; Quijada, Manuel A.

2017-08-01

For many years, acoustic systems have been used as the primary method for underwater communication; however, the data transfer rate of such systems is low because sound propagates slowly through water. A higher throughput can be achieved using visible light to transmit data underwater. The first issue with this approach is that there is generally a large loss of the light signal due to scattering and absorption in water, even though there is an optimal wavelength for transmission in the blue or green wavelengths of the visible spectrum. The second issue is that a simple communication system, consisting only of a highly directional source/transmitter and small optical detector/receiver, has a very narrow field of view. The goal of this project is to improve an optical, underwater communication system by increasing the effective field of view of the receiving optics. To this end, we make two changes to the simple system: (1) An optical dome was added near the receiver. An array of lenses is placed radially on the surface of the dome, reminiscent of the compound eye of an insect. The lenses make the source and detector planes conjugate, and each lens adds a new region of the source plane to the instrument's total field of view. (2) The receiver was expanded to include multiple photodiodes. With these two changes, the receiver has much more tolerance to misalignments (in position and angle) of the transmitter. Two versions of the optical dome (with 6" and 8" diameters) were designed using PTC's Creo CAD software and modeled using Synopsys' CODE V optical design software. A series of these transparent hemispherical domes, with both design diameters, were manufactured using a 5-axis mill. The prototype was then retrofitted with lenses and compared with the computer-generated model to demonstrate the effectiveness of this solution. This work shows that the dome design improves the optical field of view of the underwater communication system considerably. Furthermore, with the experimental test results, a geometric optimization model was derived providing insights to the design performance limits.

Hemispherical Optical Dome for Underwater Communication

NASA Technical Reports Server (NTRS)

Shiri, Ron S.; Lunde, Emily L.; Coronado, Patrick L.; Quijada, Manuel A.

2017-01-01

For many years, acoustic systems have been used as the primary method for underwater communication; however, the data transfer rate of such systems is low because sound propagates slowly through the water. A higher throughput can be achieved using visible light to transmit data underwater. The first issue with using this approach is that there is generally a large loss of the light signal due to scattering and absorption in water even though there is an optimal wavelength for transmission in the blue or green wavelengths of the visible spectrum. The second issue is that a simple system consisting only of a highly directional source/transmitter and small optical detector/receiver has a very narrow field of view. The goal of this project is to improve an optical, underwater communication system by increasing the effective field of view of the receiving optics. To this end, we make two changes to the simple system: (1) An optical dome was added near the receiver. An array of lenses is placed radially on the surface of the dome, reminiscent of the compound eye of an insect. The lenses make the source and detector planes conjugate, and each lens adds a new region of the source plane to the instrument's total field of view. (2) The receiver was expanded to include multiple photodiodes. With these two changes, the receiver has much more tolerance to misalignments (in position and angle) of the transmitter.Two versions of the optical dome (with 6 and 8 diameters) were designed using the CREO CAD software and modeled using the CODE V optical design software. A series of these transparent hemispherical domes, with both design diameters, were manufactured using a 5-axis mill. The prototype was then retrofitted with lenses and compared with the computer-generated model to demonstrate the effectiveness of this solution. This work shows the dome design improves the optical field of view of the underwater communication system considerably. Furthermore, with the experimental test results, a geometric optimization model was derived providing insights to the design performance limits.

Near-threshold equal-loudness contours for harbor seals (Phoca vitulina) derived from reaction times during underwater audiometry: a preliminary study.

PubMed

Kastelein, Ronald A; Wensveen, Paul J; Terhune, John M; de Jong, Christ A F

2011-01-01

Equal-loudness functions describe relationships between the frequencies of sounds and their perceived loudness. This pilot study investigated the possibility of deriving equal-loudness contours based on the assumption that sounds of equal perceived loudness elicit equal reaction times (RTs). During a psychoacoustic underwater hearing study, the responses of two young female harbor seals to tonal signals between 0.125 and 100 kHz were filmed. Frame-by-frame analysis was used to quantify RT (the time between the onset of the sound stimulus and the onset of movement of the seal away from the listening station). Near-threshold equal-latency contours, as surrogates for equal-loudness contours, were estimated from RT-level functions fitted to mean RT data. The closer the received sound pressure level was to the 50% detection hearing threshold, the more slowly the animals reacted to the signal (RT range: 188-982 ms). Equal-latency contours were calculated relative to the RTs shown by each seal at sound levels of 0, 10, and 20 dB above the detection threshold at 1 kHz. Fifty percent detection thresholds are obtained with well-trained subjects actively listening for faint familiar sounds. When calculating audibility ranges of sounds for harbor seals in nature, it may be appropriate to consider levels 20 dB above this threshold.

Some aspects of coupling-induced sound absorption in enclosures.

PubMed

Sum, K S; Pan, J

2003-08-01

It is known that the coupling between a modally reactive boundary structure of an enclosure and the enclosed sound field induces absorption in the sound field. However, the effect of this absorption on the sound-field response can vary significantly, even when material properties of the structure and dimensions of the coupled system are not changed. Although there have been numerous investigations of coupling between a structure and an enclosed sound field, little work has been done in the area of sound absorption induced by the coupling. Therefore, characteristics of the absorption are not well understood and the extent of its influence on the behavior of the sound-field response is not clearly known. In this paper, the coupling of a boundary structure and an enclosed sound field in frequency bands above the low-frequency range is considered. Three aspects of the coupling-induced sound absorption are studied namely, the effects of exciting either the structure or the sound field directly, damping in the uncoupled sound field and damping in the uncoupled structure. The results provide an understanding of some features of the coupling-induced absorption and its significance to the sound-field response.

Forward Sound Propagation Around Seamounts: Application of Acoustic Models to the Kermit-Roosevelt and Elvis Seamounts

DTIC Science & Technology

2009-06-01

large number of range steps. Brooke et al. [73] developed a Canadian Parabolic Equation model ( PECan ). In the model, the split-step Padé algorithm... PECan : A Canadian parabolic equation model for underwater sound propagation. J. Computational Acoustics, 9(1):69-100, 2001 [74] Michael D

Investigations of the Sound Generated by Supercavity Ventilation

DTIC Science & Technology

2009-08-20

2 1.2.2 Supercavitating vehicles . . . . . . . . . . . . . . . . . . . . . . . 3 1.2.3...1.1 Motivation The successful development of high-speed supercavitating underwater vehicles is an im- portant U.S. Navy objective. All aspects of...provide naval researchers with an understanding of the characteristics of the sound generated by the ventilating jets of a supercavitating vehicle

Long-term underwater sound measurements in the shipping noise indicator bands 63Hz and 125Hz from the port of Falmouth Bay, UK.

PubMed

Garrett, J K; Blondel, Ph; Godley, B J; Pikesley, S K; Witt, M J; Johanning, L

2016-09-15

Chronic low-frequency anthropogenic sound, such as shipping noise, may be negatively affecting marine life. The EU's Marine Strategy Framework Directive (MSFD) includes a specific indicator focused on this noise. This indicator is the yearly average sound level in third-octave bands with centre frequencies at 63Hz and 125Hz. These levels are described for Falmouth Bay, UK, an active port at the entrance to the English Channel. Underwater sound was recorded for 30min h(-1) over the period June 2012 to November 2013 for a total of 435days. Mean third-octave levels were louder in the 125-Hz band (annual mean level of 96.0dB re 1μPa) than in the 63-Hz band (92.6dB re 1 μPa). These levels and variations are assessed as a function of seasons, shipping activity and wave height, providing comparison points for future monitoring activities, including the MSFD and emerging international regulation. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Research on the optoacoustic communication system for speech transmission by variable laser-pulse repetition rates

NASA Astrophysics Data System (ADS)

Jiang, Hongyan; Qiu, Hongbing; He, Ning; Liao, Xin

2018-06-01

For the optoacoustic communication from in-air platforms to submerged apparatus, a method based on speech recognition and variable laser-pulse repetition rates is proposed, which realizes character encoding and transmission for speech. Firstly, the theories and spectrum characteristics of the laser-generated underwater sound are analyzed; and moreover character conversion and encoding for speech as well as the pattern of codes for laser modulation is studied; lastly experiments to verify the system design are carried out. Results show that the optoacoustic system, where laser modulation is controlled by speech-to-character baseband codes, is beneficial to improve flexibility in receiving location for underwater targets as well as real-time performance in information transmission. In the overwater transmitter, a pulse laser is controlled to radiate by speech signals with several repetition rates randomly selected in the range of one to fifty Hz, and then in the underwater receiver laser pulse repetition rate and data can be acquired by the preamble and information codes of the corresponding laser-generated sound. When the energy of the laser pulse is appropriate, real-time transmission for speaker-independent speech can be realized in that way, which solves the problem of underwater bandwidth resource and provides a technical approach for the air-sea communication.

Oyster Larvae Settle in Response to Habitat-Associated Underwater Sounds

PubMed Central

Lillis, Ashlee; Eggleston, David B.; Bohnenstiehl, DelWayne R.

2013-01-01

Following a planktonic dispersal period of days to months, the larvae of benthic marine organisms must locate suitable seafloor habitat in which to settle and metamorphose. For animals that are sessile or sedentary as adults, settlement onto substrates that are adequate for survival and reproduction is particularly critical, yet represents a challenge since patchily distributed settlement sites may be difficult to find along a coast or within an estuary. Recent studies have demonstrated that the underwater soundscape, the distinct sounds that emanate from habitats and contain information about their biological and physical characteristics, may serve as broad-scale environmental cue for marine larvae to find satisfactory settlement sites. Here, we contrast the acoustic characteristics of oyster reef and off-reef soft bottoms, and investigate the effect of habitat-associated estuarine sound on the settlement patterns of an economically and ecologically important reef-building bivalve, the Eastern oyster (Crassostrea virginica). Subtidal oyster reefs in coastal North Carolina, USA show distinct acoustic signatures compared to adjacent off-reef soft bottom habitats, characterized by consistently higher levels of sound in the 1.5–20 kHz range. Manipulative laboratory playback experiments found increased settlement in larval oyster cultures exposed to oyster reef sound compared to unstructured soft bottom sound or no sound treatments. In field experiments, ambient reef sound produced higher levels of oyster settlement in larval cultures than did off-reef sound treatments. The results suggest that oyster larvae have the ability to respond to sounds indicative of optimal settlement sites, and this is the first evidence that habitat-related differences in estuarine sounds influence the settlement of a mollusk. Habitat-specific sound characteristics may represent an important settlement and habitat selection cue for estuarine invertebrates and could play a role in driving settlement and recruitment patterns in marine communities. PMID:24205381

Oyster larvae settle in response to habitat-associated underwater sounds.

PubMed

Lillis, Ashlee; Eggleston, David B; Bohnenstiehl, DelWayne R

2013-01-01

Following a planktonic dispersal period of days to months, the larvae of benthic marine organisms must locate suitable seafloor habitat in which to settle and metamorphose. For animals that are sessile or sedentary as adults, settlement onto substrates that are adequate for survival and reproduction is particularly critical, yet represents a challenge since patchily distributed settlement sites may be difficult to find along a coast or within an estuary. Recent studies have demonstrated that the underwater soundscape, the distinct sounds that emanate from habitats and contain information about their biological and physical characteristics, may serve as broad-scale environmental cue for marine larvae to find satisfactory settlement sites. Here, we contrast the acoustic characteristics of oyster reef and off-reef soft bottoms, and investigate the effect of habitat-associated estuarine sound on the settlement patterns of an economically and ecologically important reef-building bivalve, the Eastern oyster (Crassostrea virginica). Subtidal oyster reefs in coastal North Carolina, USA show distinct acoustic signatures compared to adjacent off-reef soft bottom habitats, characterized by consistently higher levels of sound in the 1.5-20 kHz range. Manipulative laboratory playback experiments found increased settlement in larval oyster cultures exposed to oyster reef sound compared to unstructured soft bottom sound or no sound treatments. In field experiments, ambient reef sound produced higher levels of oyster settlement in larval cultures than did off-reef sound treatments. The results suggest that oyster larvae have the ability to respond to sounds indicative of optimal settlement sites, and this is the first evidence that habitat-related differences in estuarine sounds influence the settlement of a mollusk. Habitat-specific sound characteristics may represent an important settlement and habitat selection cue for estuarine invertebrates and could play a role in driving settlement and recruitment patterns in marine communities.

Underwater image enhancement through depth estimation based on random forest

NASA Astrophysics Data System (ADS)

Tai, Shen-Chuan; Tsai, Ting-Chou; Huang, Jyun-Han

2017-11-01

Light absorption and scattering in underwater environments can result in low-contrast images with a distinct color cast. This paper proposes a systematic framework for the enhancement of underwater images. Light transmission is estimated using the random forest algorithm. RGB values, luminance, color difference, blurriness, and the dark channel are treated as features in training and estimation. Transmission is calculated using an ensemble machine learning algorithm to deal with a variety of conditions encountered in underwater environments. A color compensation and contrast enhancement algorithm based on depth information was also developed with the aim of improving the visual quality of underwater images. Experimental results demonstrate that the proposed scheme outperforms existing methods with regard to subjective visual quality as well as objective measurements.

On the importance of measurement system calibration for underwater passive monitoring

NASA Astrophysics Data System (ADS)

Miqueleti, S. A.; Costa-Félix, R. P. B.

2016-07-01

The underwater passive acoustic monitoring of sound in oceans is growing in recent years and has served as a source of information on marine life and the interference of human activities on the environment. The recordings are used for species identification and prevention of potential adverse effects of vessel traffic, sonar and offshore activities as a whole. However, not much attention is given to the calibration of the hydrophone used to ensure the validity of the information collected. The resulting sound depends on the input audio, and the transfer function of the intensity of the input signal. This paper presents an assessment of how the lack of calibration of hydroacoustic systems might compromise the evaluation of the marine environment.

Underwater Equal-Latency Contours of a Harbor Porpoise (Phocoena phocoena) for Tonal Signals Between 0.5 and 125 kHz.

PubMed

Wensveen, Paul J; Huijser, Léonie A E; Hoek, Lean; Kastelein, Ronald A

2016-01-01

Loudness perception can be studied based on the assumption that sounds of equal loudness elicit equal reaction time (RT; or "response latency"). We measured the underwater RTs of a harbor porpoise to narrowband frequency-modulated sounds and constructed six equal-latency contours. The contours paralleled the audiogram at low sensation levels (high RTs). At high-sensation levels, contours flattened between 0.5 and 31.5 kHz but dropped substantially (RTs shortened) beyond those frequencies. This study suggests that equal-latency-based frequency weighting can emulate noise perception in porpoises for low and middle frequencies but that the RT-loudness correlation is relatively weak for very high frequencies.

Abiotic control of underwater light in a drinking water reservoir: Photon budget analysis and implications for water quality monitoring

NASA Astrophysics Data System (ADS)

Watanabe, Shohei; Laurion, Isabelle; Markager, Stiig; Vincent, Warwick F.

2015-08-01

In optically complex inland waters, the underwater attenuation of photosynthetically active radiation (PAR) is controlled by a variable combination of absorption and scattering components of the lake or river water. Here we applied a photon budget approach to identify the main optical components affecting PAR attenuation in Lake St. Charles, a drinking water reservoir for Québec City, Canada. This analysis showed the dominant role of colored dissolved organic matter (CDOM) absorption (average of 44% of total absorption during the sampling period), but with large changes over depth in the absolute and relative contribution of the individual absorption components (water, nonalgal particulates, phytoplankton and CDOM) to PAR attenuation. This pronounced vertical variation occurred because of the large spectral changes in the light field with depth, and it strongly affected the average in situ diffuse absorption coefficients in the water column. For example, the diffuse absorption coefficient for pure-water in the ambient light field was 10-fold higher than the value previously measured in the blue open ocean and erroneously applied to lakes and coastal waters. Photon absorption budget calculations for a range of limnological conditions confirmed that phytoplankton had little direct influence on underwater light, even at chlorophyll a values above those observed during harmful algal blooms in the lake. These results imply that traditional measures of water quality such as Secchi depth and radiometric transparency do not provide a meaningful estimate of the biological state of the water column in CDOM-colored lakes and reservoirs.

A simple underwater imaging model.

PubMed

Hou, Weilin

2009-09-01

It is commonly known that underwater imaging is hindered by both absorption and scattering by particles of various origins. However, evidence also indicates that the turbulence in natural underwater environments can cause severe image-quality degradation. A model is presented to include the effects of both particle and turbulence on underwater optical imaging through optical transfer functions to help quantify the limiting factors under different circumstances. The model utilizes Kolmogorov-type index of refraction power spectra found in the ocean, along with field examples, to demonstrate that optical turbulence can limit imaging resolution by affecting high spatial frequencies. The effects of the path radiance are also discussed.

Hearing of the African lungfish (Protopterus annectens) suggests underwater pressure detection and rudimentary aerial hearing in early tetrapods.

PubMed

Christensen, Christian Bech; Christensen-Dalsgaard, Jakob; Madsen, Peter Teglberg

2015-02-01

In the transition from an aquatic to a terrestrial lifestyle, vertebrate auditory systems have undergone major changes while adapting to aerial hearing. Lungfish are the closest living relatives of tetrapods and their auditory system may therefore be a suitable model of the auditory systems of early tetrapods such as Acanthostega. Therefore, experimental studies on the hearing capabilities of lungfish may shed light on the possible hearing capabilities of early tetrapods and broaden our understanding of hearing across the water-to-land transition. Here, we tested the hypotheses that (i) lungfish are sensitive to underwater pressure using their lungs as pressure-to-particle motion transducers and (ii) lungfish can detect airborne sound. To do so, we used neurophysiological recordings to estimate the vibration and pressure sensitivity of African lungfish (Protopterus annectens) in both water and air. We show that lungfish detect underwater sound pressure via pressure-to-particle motion transduction by air volumes in their lungs. The morphology of lungfish shows no specialized connection between these air volumes and the inner ears, and so our results imply that air breathing may have enabled rudimentary pressure detection as early as the Devonian era. Additionally, we demonstrate that lungfish in spite of their atympanic middle ear can detect airborne sound through detection of sound-induced head vibrations. This strongly suggests that even vertebrates with no middle ear adaptations for aerial hearing, such as the first tetrapods, had rudimentary aerial hearing that may have led to the evolution of tympanic middle ears in recent tetrapods. © 2015. Published by The Company of Biologists Ltd.

75 FR 25729 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-07

... (eight species of true porpoises, six species of river dolphins, Kogia, the franciscana, and four species... specifically designed for such operations in the Arctic. Underwater sound propagation results from the use of... often true even in cases when the sounds must be readily audible to the animals based on measured...

Characterization of Underwater Sounds Produced by a Backhoe Dredge Excavating Rock and Gravel

DTIC Science & Technology

2012-12-01

bathymetry, hydrodynamic conditions, prevalence of non-dredging ambient sounds), this study fills important knowledge gaps that contribute to better... Beaver Mackenzie, peak spectral levels were 122 dB at 190 m with a peak frequency of 120 Hz. Received levels in the 20- to 1000-Hz band were 133 dB

Global Ocean Forecast System V3.0 Validation Test Report Addendum: Addition of the Diurnal Cycle

DTIC Science & Technology

2010-11-05

upper ocean forming a thin mixed layer and have a profound impact on the sound speed profile and surface duct (e.g. Urick , 1983). When the solar...7320--10-9236. Urick , R.J., 1983: Principles of underwater sound, 3 rd Edition. Peninsula Publishing, Los Altos, California, 423 pp. 11 7.0

76 FR 6406 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to a...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-04

... be present during the project's timeline may be exposed to sound pressure levels associated with... of the wharf's existing piling sub-structure. Under the proposed action, ninety-six 24-in (0.6 m... loss formulas (the practical spreading loss equation for underwater sounds and the spherical spreading...

Highly efficient isolation of waterborne sound by an air-sealed meta-screen

NASA Astrophysics Data System (ADS)

Bai, Xiaoxue; Qiu, Chunyin; Wen, Xinhua; Peng, Shasha; Ke, Manzhu; Liu, Zhengyou

2017-05-01

Underwater sound isolation has been a long-standing fundamental issue in industry and military fields. Starting from a simple theoretical model, here an air-sealed meta-screen is proposed to overcome this problem. Comparing with the sample without filling air, the effective impedance of the air-sealed one is greatly reduced and strikingly mismatch with water, accompanying another merit of low sound speed. Deeply suppressed sound transmission (˜50 dB) through such a meta-screen is observed experimentally over a wide range of ultrasonic frequencies and incident angles.

Sound Absorption Characteristics of Aluminum Foams Treated by Plasma Electrolytic Oxidation

PubMed Central

Jin, Wei; Liu, Jiaan; Wang, Zhili; Wang, Yonghua; Cao, Zheng; Liu, Yaohui; Zhu, Xianyong

2015-01-01

Open-celled aluminum foams with different pore sizes were fabricated. A plasma electrolytic oxidation (PEO) treatment was applied on the aluminum foams to create a layer of ceramic coating. The sound absorption coefficients of the foams were measured by an impedance tube and they were calculated by a transfer function method. The experimental results show that the sound absorption coefficient of the foam increases gradually with the decrease of pore size. Additionally, when the porosity of the foam increases, the sound absorption coefficient also increases. The PEO coating surface is rough and porous, which is beneficial for improvement in sound absorption. After PEO treatment, the maximum sound absorption of the foam is improved to some extent. PMID:28793653

Assessing underwater noise levels during pile-driving at an offshore windfarm and its potential effects on marine mammals.

PubMed

Bailey, Helen; Senior, Bridget; Simmons, Dave; Rusin, Jan; Picken, Gordon; Thompson, Paul M

2010-06-01

Marine renewable developments have raised concerns over impacts of underwater noise on marine species, particularly from pile-driving for wind turbines. Environmental assessments typically use generic sound propagation models, but empirical tests of these models are lacking. In 2006, two 5MW wind turbines were installed off NE Scotland. The turbines were in deep (>40m) water, 25km from the Moray Firth Special Area of Conservation (SAC), potentially affecting a protected population of bottlenose dolphins. We measured pile-driving noise at distances of 0.1 (maximum broadband peak to peak sound level 205dB re 1microPa) to 80km (no longer distinguishable above background noise). These sound levels were related to noise exposure criteria for marine mammals to assess possible effects. For bottlenose dolphins, auditory injury would only have occurred within 100m of the pile-driving and behavioural disturbance, defined as modifications in behaviour, could have occurred up to 50km away.

Underwater noise pollution in a coastal tropical environment.

PubMed

Bittencourt, L; Carvalho, R R; Lailson-Brito, J; Azevedo, A F

2014-06-15

Underwater noise pollution has become a major concern in marine habitats. Guanabara Bay, southeastern Brazil, is an impacted area of economic importance with constant vessel traffic. One hundred acoustic recording sessions took place over ten locations. Sound sources operating within 1 km radius of each location were quantified during recordings. The highest mean sound pressure level near the surface was 111.56±9.0 dB re 1 μPa at the frequency band of 187 Hz. Above 15 kHz, the highest mean sound pressure level was 76.21±8.3 dB re 1 μPa at the frequency 15.89 kHz. Noise levels correlated with number of operating vessels and vessel traffic composition influenced noise profiles. Shipping locations had the highest noise levels, while small vessels locations had the lowest noise levels. Guanabara Bay showed noise pollution similar to that of other impacted coastal regions, which is related to shipping and vessel traffic. Copyright © 2014 Elsevier Ltd. All rights reserved.

Impact of Vessel Noise on Oyster Toadfish (Opsanus tau) Behavior and Implications for Underwater Noise Management

NASA Astrophysics Data System (ADS)

Krahforst, Cecilia S.

Underwater noise and its impacts on marine life are growing management concerns. This dissertation considers both the ecological and social concerns of underwater noise, using the oyster toadfish (Opsanus tau) as a model species. Oyster toadfish call for mates using a boatwhistle sound, but increased ambient noise levels from vessels or other anthropogenic activities are likely to influence the ability of males to find mates. If increased ambient noise levels reduce fish fitness then underwater noise can impact socially valued ecosystem services (e.g. fisheries). The following ecological objectives of the impacts of underwater noise on oyster toadfish were investigated: (1) to determine how noise influences male calling behavior; (2) to assess how areas of high vessel activity ("noisy") and low vessel activity ("quiet") influence habitat utilization (fish standard length and occupancy rate); and (3) to discover if fitness (number of clutches and number of embryos per clutch) is lower in "noisy" compared with "quiet" sites. Field experiments were executed in "noisy" and "quiet" areas. Recorded calls by males in response to playback sounds (vessel, predator, and snapping shrimp sounds) and egg deposition by females ("noisy" vs. "quiet" sites) demonstrated that oyster toadfish are impacted by underwater noise. First, males decreased their call rates and called louder in response to increased ambient noise levels. Second, oyster toadfish selected nesting sites in areas with little or no inboard motorboat activity. Third, male oyster toadfish at "noisy" sites either had no egg clutches on their shelters or the number of embryos per clutch was significantly lower than in the "quiet" areas. Underwater noise and disturbance from vessels are influencing the fitness of the oyster toadfish. The social significance of the growing concerns regarding underwater noise was investigated by identifying dominant themes found within two types of texts: four recent underwater noise management strategy papers and 14 texts from the federal enabling legislation. To uncover themes that might reveal underlying cultural patterns and values, word frequency of key terms in each set of documents was compared using a correspondence analysis and network analyses. The predominant theme within the noise management documents was "assessing the acoustic impacts and protecting marine life [esp. marine mammals]." The legislative documents spanned a range of concerns but focused primarily on themes associated with the trade-offs between human use and the environment, such as resource "conservation" and "development." In terms of marine life, the enabling federal legislation used "fish" and the noise management documents focused on "marine mammals" as their primary animal of concern. This disparity between document types explained the paucity of ecosystem services that were discussed in the noise management documents because fish and fisheries provide important ecosystem services to the human population. By focusing more on the concept of fish, the noise management documents would be more effective at incorporating ecosystem services, which is likely to be more socially accepted than the current management initiatives.

Game Theory-Based Cooperation for Underwater Acoustic Sensor Networks: Taxonomy, Review, Research Challenges and Directions

PubMed Central

Muhammed, Dalhatu; Anisi, Mohammad Hossein; Vargas-Rosales, Cesar; Khan, Anwar

2018-01-01

Exploring and monitoring the underwater world using underwater sensors is drawing a lot of attention these days. In this field cooperation between acoustic sensor nodes has been a critical problem due to the challenging features such as acoustic channel failure (sound signal), long propagation delay of acoustic signal, limited bandwidth and loss of connectivity. There are several proposed methods to improve cooperation between the nodes by incorporating information/game theory in the node’s cooperation. However, there is a need to classify the existing works and demonstrate their performance in addressing the cooperation issue. In this paper, we have conducted a review to investigate various factors affecting cooperation in underwater acoustic sensor networks. We study various cooperation techniques used for underwater acoustic sensor networks from different perspectives, with a concentration on communication reliability, energy consumption, and security and present a taxonomy for underwater cooperation. Moreover, we further review how the game theory can be applied to make the nodes cooperate with each other. We further analyze different cooperative game methods, where their performance on different metrics is compared. Finally, open issues and future research direction in underwater acoustic sensor networks are highlighted. PMID:29389874

Game Theory-Based Cooperation for Underwater Acoustic Sensor Networks: Taxonomy, Review, Research Challenges and Directions.

PubMed

Muhammed, Dalhatu; Anisi, Mohammad Hossein; Zareei, Mahdi; Vargas-Rosales, Cesar; Khan, Anwar

2018-02-01

Exploring and monitoring the underwater world using underwater sensors is drawing a lot of attention these days. In this field cooperation between acoustic sensor nodes has been a critical problem due to the challenging features such as acoustic channel failure (sound signal), long propagation delay of acoustic signal, limited bandwidth and loss of connectivity. There are several proposed methods to improve cooperation between the nodes by incorporating information/game theory in the node's cooperation. However, there is a need to classify the existing works and demonstrate their performance in addressing the cooperation issue. In this paper, we have conducted a review to investigate various factors affecting cooperation in underwater acoustic sensor networks. We study various cooperation techniques used for underwater acoustic sensor networks from different perspectives, with a concentration on communication reliability, energy consumption, and security and present a taxonomy for underwater cooperation. Moreover, we further review how the game theory can be applied to make the nodes cooperate with each other. We further analyze different cooperative game methods, where their performance on different metrics is compared. Finally, open issues and future research direction in underwater acoustic sensor networks are highlighted.

Low complexity lossless compression of underwater sound recordings.

PubMed

Johnson, Mark; Partan, Jim; Hurst, Tom

2013-03-01

Autonomous listening devices are increasingly used to study vocal aquatic animals, and there is a constant need to record longer or with greater bandwidth, requiring efficient use of memory and battery power. Real-time compression of sound has the potential to extend recording durations and bandwidths at the expense of increased processing operations and therefore power consumption. Whereas lossy methods such as MP3 introduce undesirable artifacts, lossless compression algorithms (e.g., flac) guarantee exact data recovery. But these algorithms are relatively complex due to the wide variety of signals they are designed to compress. A simpler lossless algorithm is shown here to provide compression factors of three or more for underwater sound recordings over a range of noise environments. The compressor was evaluated using samples from drifting and animal-borne sound recorders with sampling rates of 16-240 kHz. It achieves >87% of the compression of more-complex methods but requires about 1/10 of the processing operations resulting in less than 1 mW power consumption at a sampling rate of 192 kHz on a low-power microprocessor. The potential to triple recording duration with a minor increase in power consumption and no loss in sound quality may be especially valuable for battery-limited tags and robotic vehicles.

Evaluation of a Single-Beam Sonar System to Map Seagrass at Two Sites in Northern Puget Sound, Washington

USGS Publications Warehouse

Stevens, Andrew W.; Lacy, Jessica R.; Finlayson, David P.; Gelfenbaum, Guy

2008-01-01

Seagrass at two sites in northern Puget Sound, Possession Point and nearby Browns Bay, was mapped using both a single-beam sonar and underwater video camera. The acoustic and underwater video data were compared to evaluate the accuracy of acoustic estimates of seagrass cover. The accuracy of the acoustic method was calculated for three classifications of seagrass observed in underwater video: bare (no seagrass), patchy seagrass, and continuous seagrass. Acoustic and underwater video methods agreed in 92 percent and 74 percent of observations made in bare and continuous areas, respectively. However, in patchy seagrass, the agreement between acoustic and underwater video was poor (43 percent). The poor agreement between the two methods in areas with patchy seagrass is likely because the two instruments were not precisely colocated. The distribution of seagrass at the two sites differed both in overall percent vegetated and in the distribution of percent cover versus depth. On the basis of acoustic data, seagrass inhabited 0.29 km2 (19 percent of total area) at Possession Point and 0.043 km2 (5 percent of total area) at the Browns Bay study site. The depth distribution at the two sites was markedly different. Whereas the majority of seagrass at Possession Point occurred between -0.5 and -1.5 m MLLW, most seagrass at Browns Bay occurred at a greater depth, between -2.25 and -3.5 m MLLW. Further investigation of the anthropogenic and natural factors causing these differences in distribution is needed.

Sound absorption characteristics of tree bark and forest floor

Treesearch

G. Reethof; O. H. McDaniel; G. M. Heisler

1977-01-01

Results of basic research on absorption of sound by tree bark and forest floors are presented. Amount of sound absorption by tree bark was determined by laboratory experiments with bark samples in a standing-wave tube. A modified portable standing-wave tube was used to measure absorption of sound by forest floors with different moisture contents, with and without leaf...

Another round for noisy ocean temperature test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, C.

1993-03-05

It's a deal a talk show host would kill for: $35 million to sound off for a while. But there's one other aspect of the bargain that might be a bit tough for the average radio personality: You've got to listen to your own noise and gauge whether the world is warming. Luckily, that's nothing new for oceanographer Walter Munk, who last week won funding from the Defense Advanced Research Projects Agency to conduct a second trial of his underwater sonic thermometer of the world's oceans. Sound waves are pulsed form underwater loudspeakers to receivers thousands of miles away. Bymore » the measuring the elapsed time, Munk and his collaborators can precisely measure temperatures in entire ocean basins and watch for signs of global warming.« less

Measurement of Underwater Operational Noise Emitted by Wave and Tidal Stream Energy Devices.

PubMed

Lepper, Paul A; Robinson, Stephen P

2016-01-01

The increasing international growth in the development of marine and freshwater wave and tidal energy harvesting systems has been followed by a growing requirement to understand any associated underwater impact. Radiated noise generated during operation is dependent on the device's physical properties, the sound-propagation environment, and the device's operational state. Physical properties may include size, distribution in the water column, and mechanics/hydrodynamics. The sound-propagation environment may be influenced by water depth, bathymetry, sediment type, and water column acoustic properties, and operational state may be influenced by tidal cycle and wave height among others This paper discusses some of the challenges for measurement of noise characteristics from these devices as well as a case study of the measurement of radiated noise from a full-scale wave energy converter.

A study on practical use of underwater abrasive water jet cutting

NASA Astrophysics Data System (ADS)

Yamaguchi, Hitoshi; Demura, Kenji

1993-09-01

The practicality of underwater abrasive water jet cutting technology was studied in experiments. A study of abrasives in slurried form showed that optimum polymer concentration can be selected to suit underwater conditions. For the long-distance transport of slurry from the ocean surface to the ocean floor, a direct supply system by hose proved to be practical. This system takes advantage of the insolubility of the slurry in water due to a difference in specific gravity. For cutting thick steel plate at great ocean depths, a simulation with a pressurized container revealed the requirements for actual cutting. Confirmation of remote cutting operations will become the most important technology in field applications. Underwater sound vibration characteristics were found to change significantly in direct response to modifications in cutting conditions. This will be important basic data to develop an effective sensoring method.

Hybrid acoustic metamaterial as super absorber for broadband low-frequency sound

PubMed Central

Tang, Yufan; Ren, Shuwei; Meng, Han; Xin, Fengxian; Huang, Lixi; Chen, Tianning; Zhang, Chuanzeng; Lu, Tian Jain

2017-01-01

A hybrid acoustic metamaterial is proposed as a new class of sound absorber, which exhibits superior broadband low-frequency sound absorption as well as excellent mechanical stiffness/strength. Based on the honeycomb-corrugation hybrid core (H-C hybrid core), we introduce perforations on both top facesheet and corrugation, forming perforated honeycomb-corrugation hybrid (PHCH) to gain super broadband low-frequency sound absorption. Applying the theory of micro-perforated panel (MPP), we establish a theoretical method to calculate the sound absorption coefficient of this new kind of metamaterial. Perfect sound absorption is found at just a few hundreds hertz with two-octave 0.5 absorption bandwidth. To verify this model, a finite element model is developed to calculate the absorption coefficient and analyze the viscous-thermal energy dissipation. It is found that viscous energy dissipation at perforation regions dominates the total energy consumed. This new kind of acoustic metamaterials show promising engineering applications, which can serve as multiple functional materials with extraordinary low-frequency sound absorption, excellent stiffness/strength and impact energy absorption. PMID:28240239

Preparation and Sound Absorption Properties of a Barium Titanate/Nitrile Butadiene Rubber–Polyurethane Foam Composite with Multilayered Structure

PubMed Central

Jiang, Xueliang; Yang, Zhen; Wang, Zhijie; Zhang, Fuqing; You, Feng

2018-01-01

Barium titanate/nitrile butadiene rubber (BT/NBR) and polyurethane (PU) foam were combined to prepare a sound-absorbing material with an alternating multilayered structure. The effects of the cell size of PU foam and the alternating unit number on the sound absorption property of the material were investigated. The results show that the sound absorption efficiency at a low frequency increased when decreasing the cell size of PU foam layer. With the increasing of the alternating unit number, the material shows the sound absorption effect in a wider bandwidth of frequency. The BT/NBR-PU foam composites with alternating multilayered structure have an excellent sound absorption property at low frequency due to the organic combination of airflow resistivity, resonance absorption, and interface dissipation. PMID:29565321

Preparation and Sound Absorption Properties of a Barium Titanate/Nitrile Butadiene Rubber-Polyurethane Foam Composite with Multilayered Structure.

PubMed

Jiang, Xueliang; Yang, Zhen; Wang, Zhijie; Zhang, Fuqing; You, Feng; Yao, Chu

2018-03-22

Barium titanate/nitrile butadiene rubber (BT/NBR) and polyurethane (PU) foam were combined to prepare a sound-absorbing material with an alternating multilayered structure. The effects of the cell size of PU foam and the alternating unit number on the sound absorption property of the material were investigated. The results show that the sound absorption efficiency at a low frequency increased when decreasing the cell size of PU foam layer. With the increasing of the alternating unit number, the material shows the sound absorption effect in a wider bandwidth of frequency. The BT/NBR-PU foam composites with alternating multilayered structure have an excellent sound absorption property at low frequency due to the organic combination of airflow resistivity, resonance absorption, and interface dissipation.

Common sole larvae survive high levels of pile-driving sound in controlled exposure experiments.

PubMed

Bolle, Loes J; de Jong, Christ A F; Bierman, Stijn M; van Beek, Pieter J G; van Keeken, Olvin A; Wessels, Peter W; van Damme, Cindy J G; Winter, Hendrik V; de Haan, Dick; Dekeling, René P A

2012-01-01

In view of the rapid extension of offshore wind farms, there is an urgent need to improve our knowledge on possible adverse effects of underwater sound generated by pile-driving. Mortality and injuries have been observed in fish exposed to loud impulse sounds, but knowledge on the sound levels at which (sub-)lethal effects occur is limited for juvenile and adult fish, and virtually non-existent for fish eggs and larvae. A device was developed in which fish larvae can be exposed to underwater sound. It consists of a rigid-walled cylindrical chamber driven by an electro-dynamical sound projector. Samples of up to 100 larvae can be exposed simultaneously to a homogeneously distributed sound pressure and particle velocity field. Recorded pile-driving sounds could be reproduced accurately in the frequency range between 50 and 1000 Hz, at zero to peak pressure levels up to 210 dB re 1µPa(2) (zero to peak pressures up to 32 kPa) and single pulse sound exposure levels up to 186 dB re 1µPa(2)s. The device was used to examine lethal effects of sound exposure in common sole (Solea solea) larvae. Different developmental stages were exposed to various levels and durations of pile-driving sound. The highest cumulative sound exposure level applied was 206 dB re 1µPa(2)s, which corresponds to 100 strikes at a distance of 100 m from a typical North Sea pile-driving site. The results showed no statistically significant differences in mortality between exposure and control groups at sound exposure levels which were well above the US interim criteria for non-auditory tissue damage in fish. Although our findings cannot be extrapolated to fish larvae in general, as interspecific differences in vulnerability to sound exposure may occur, they do indicate that previous assumptions and criteria may need to be revised.

Common Sole Larvae Survive High Levels of Pile-Driving Sound in Controlled Exposure Experiments

PubMed Central

Bolle, Loes J.; de Jong, Christ A. F.; Bierman, Stijn M.; van Beek, Pieter J. G.; van Keeken, Olvin A.; Wessels, Peter W.; van Damme, Cindy J. G.; Winter, Hendrik V.; de Haan, Dick; Dekeling, René P. A.

2012-01-01

In view of the rapid extension of offshore wind farms, there is an urgent need to improve our knowledge on possible adverse effects of underwater sound generated by pile-driving. Mortality and injuries have been observed in fish exposed to loud impulse sounds, but knowledge on the sound levels at which (sub-)lethal effects occur is limited for juvenile and adult fish, and virtually non-existent for fish eggs and larvae. A device was developed in which fish larvae can be exposed to underwater sound. It consists of a rigid-walled cylindrical chamber driven by an electro-dynamical sound projector. Samples of up to 100 larvae can be exposed simultaneously to a homogeneously distributed sound pressure and particle velocity field. Recorded pile-driving sounds could be reproduced accurately in the frequency range between 50 and 1000 Hz, at zero to peak pressure levels up to 210 dB re 1µPa2 (zero to peak pressures up to 32 kPa) and single pulse sound exposure levels up to 186 dB re 1µPa2s. The device was used to examine lethal effects of sound exposure in common sole (Solea solea) larvae. Different developmental stages were exposed to various levels and durations of pile-driving sound. The highest cumulative sound exposure level applied was 206 dB re 1µPa2s, which corresponds to 100 strikes at a distance of 100 m from a typical North Sea pile-driving site. The results showed no statistically significant differences in mortality between exposure and control groups at sound exposure levels which were well above the US interim criteria for non-auditory tissue damage in fish. Although our findings cannot be extrapolated to fish larvae in general, as interspecific differences in vulnerability to sound exposure may occur, they do indicate that previous assumptions and criteria may need to be revised. PMID:22431996

Sound absorption of a new oblique-section acoustic metamaterial with nested resonator

NASA Astrophysics Data System (ADS)

Gao, Nansha; Hou, Hong; Zhang, Yanni; Wu, Jiu Hui

2018-02-01

This study designs and investigates high-efficiency sound absorption of new oblique-section nested resonators. Impedance tube experiment results show that different combinations of oblique-section nest resonators have tunable low-frequency bandwidth characteristics. The sound absorption mechanism is due to air friction losses in the slotted region and the sample structure resonance. The acousto-electric analogy model demonstrates that the sound absorption peak and bandwidth can be modulated over an even wider frequency range by changing the geometric size and combinations of structures. The proposed structure can be easily fabricated and used in low-frequency sound absorption applications.

Underwater localization of pure tones by harbor seals (Phoca vitulina).

PubMed

Bodson, Anaïs; Miersch, Lars; Dehnhardt, Guido

2007-10-01

The underwater sound localization acuity of harbor seals (Phoca vitulina) was measured in the horizontal plane. Minimum audible angles (MAAs) of pure tones were determined as a function of frequency from 0.2 to 16 kHz for two seals. Testing was conducted in a 10-m-diam underwater half circle using a right/left psychophysical procedure. The results indicate that for both harbor seals, MAAs were large at high frequencies (13.5 degrees and 17.4 degrees at 16 kHz), transitional at intermediate frequencies (9.6 degrees and 10.1 degrees at 4 kHz), and particularly small at low frequencies (3.2 degrees and 3.1 degrees at 0.2 kHz). Harbor seals seem to be able to utilize both binaural cues, interaural time differences (ITDs) and interaural intensity differences (IIDs), but a significant decrease in the sound localization acuity with increasing frequency suggests that IID cues may not be as robust as ITD cues under water. These results suggest that the harbor seal can be regarded as a low-frequency specialist. Additionally, to obtain a MAA more representative of the species, the horizontal underwater MAA of six adult harbor seals was measured at 2 kHz under identical conditions. The MAAs of the six animals ranged from 8.8 degrees to 11.7 degrees , resulting in a mean MAA of 10.3 degrees .

Icelandic herring-eating killer whales feed at night.

PubMed

Richard, Gaëtan; Filatova, Olga A; Samarra, Filipa I P; Fedutin, Ivan D; Lammers, Marc; Miller, Patrick J

2017-01-01

Herring-eating killer whales debilitate herring with underwater tail slaps and likely herd herring into tighter schools using a feeding-specific low-frequency pulsed call ('herding' call). Feeding on herring may be dependent upon daylight, as the whales use their white underside to help herd herring; however, feeding at night has not been investigated. The production of feeding-specific sounds provides an opportunity to use passive acoustic monitoring to investigate feeding behaviour at different times of day. We compared the acoustic behaviour of killer whales between day and night, using an autonomous recorder deployed in Iceland during winter. Based upon acoustic detection of underwater tail slaps used to feed upon herring we found that killer whales fed both at night and day: they spent 50% of their time at night and 73% of daytime feeding. Interestingly, there was a significant diel variation in acoustic behaviour. Herding calls were significantly associated with underwater tail slap rate and were recorded significantly more often at night, suggesting that in low-light conditions killer whales rely more on acoustics to herd herring. Communicative sounds were also related to underwater tail slap rate and produced at different rates during day and night. The capability to adapt feeding behaviour to different light conditions may be particularly relevant for predator species occurring in high latitudes during winter, when light availability is limited.

Development of hybrid method for the prediction of underwater propeller noise

NASA Astrophysics Data System (ADS)

Seol, Hanshin; Suh, Jung-Chun; Lee, Soogab

2005-11-01

Noise reduction and control is an important problem in the performance of underwater acoustic systems and in the habitability of the passenger ship for crew and passenger. Furthermore, sound generated by a propeller is critical in underwater detection and it is often related to the survivability of the vessel especially for military purpose. This paper presents a numerical study on the non-cavitating and blade sheet cavitation noises of the underwater propeller. A brief summary of numerical method with verification and results are presented. The noise is predicted using time-domain acoustic analogy. The flow field is analyzed with potential-based panel method, and then the time-dependent pressure and sheet cavity volume data are used as the input for Ffowcs Williams-Hawkings formulation to predict the far-field acoustics. Noise characteristics are presented according to noise sources and conditions. Through this study, the dominant noise source of the underwater propeller is analyzed, which will provide a basis for proper noise control strategies.

Determination of Acoustic Effects on Marine Mammals and Sea Turtles for the Atlantic Fleet Training and Testing Environmental Impact Statement/Overseas Environmental Impact Statement

DTIC Science & Technology

2012-03-12

column than sounds with lower frequencies ( Urick , 1983). Additionally, these systems are generally operated in the vicinity of the sea floor, thus...Water,” TR-76-116, Naval Surface Weapons Center, White Oak, Silver Springs, MD. Urick , R. J. (1983), Principles of Underwater Sound, McGraw-Hill

Communication Sciences Laboratory Quarterly Progress Report, Volume 9, Number 3: Research Programs of Some of the Newer Members of CSL.

ERIC Educational Resources Information Center

Feinstein, Stephen H.; And Others

The research reported in these papers covers a variety of communication problems. The first paper covers research on sound navigation by the blind and involves echo perception research and relevant aspects of underwater sound localization. The second paper describes a research program in acoustic phonetics and concerns such related issues as…

Underwater temporary threshold shift in pinnipeds: effects of noise level and duration.

PubMed

Kastak, David; Southall, Brandon L; Schusterman, Ronald J; Kastak, Colleen Reichmuth

2005-11-01

Behavioral psychophysical techniques were used to evaluate the residual effects of underwater noise on the hearing sensitivity of three pinnipeds: a California sea lion (Zalophus californianus), a harbor seal (Phoca vitulina), and a northern elephant seal (Mirounga angustirostris). Temporary threshold shift (TTS), defined as the difference between auditory thresholds obtained before and after noise exposure, was assessed. The subjects were exposed to octave-band noise centered at 2500 Hz at two sound pressure levels: 80 and 95 dB SL (re: auditory threshold at 2500 Hz). Noise exposure durations were 22, 25, and 50 min. Threshold shifts were assessed at 2500 and 3530 Hz. Mean threshold shifts ranged from 2.9-12.2 dB. Full recovery of auditory sensitivity occurred within 24 h of noise exposure. Control sequences, comprising sham noise exposures, did not result in significant mean threshold shifts for any subject. Threshold shift magnitudes increased with increasing noise sound exposure level (SEL) for two of the three subjects. The results underscore the importance of including sound exposure metrics (incorporating sound pressure level and exposure duration) in order to fully assess the effects of noise on marine mammal hearing.

Diel and seasonal patterns of underwater sounds by Weddell seals, leopard seals, and killer whales in the Antarctic: When it's adaptive to be quiet

NASA Astrophysics Data System (ADS)

Mindach, Debrah; Thomas, Jeanette

2005-09-01

Automated underwater recordings taken during the austral breeding season of the Weddell seal (Leptonychotes weddellii) in Antarctica also provided data on the vocalizations of predators in the area; leopard seals (Hydrurga leptonyx) and killer whales (Orcinus orca). Weddell seals inhabit fast ice areas to give birth, mate, and molt. Near the end of the breeding season in December the fast ice often breaks out and the two pack ice predators are able to move near the Weddell seal colonies and prey on them, especially pups. Recordings were taken continuously for a 2.5-min period each hour from mid-October 1977 and late-January 1978 at Hutton Cliffs and South Turtle Rock Crack, in McMurdo Sound. The leopard seals increased their trill calls when killer whales came into the area as evidenced by an increase in their frequency-modulated squeak calls. Weddell seals decreased their vocalization rate dramatically (~10 sounds/min) compared to during the peak of the breeding season (~75 sounds/min). Perhaps by being quiet, Weddell seals do not attract predators to their area.

The effect of climate on acoustic signals: does atmospheric sound absorption matter for bird song and bat echolocation?

PubMed

Snell-Rood, Emilie C

2012-02-01

The divergence of signals along ecological gradients may lead to speciation. The current research tests the hypothesis that variation in sound absorption selects for divergence in acoustic signals along climatic gradients, which has implications for understanding not only diversification, but also how organisms may respond to climate change. Because sound absorption varies with temperature, humidity, and the frequency of sound, individuals or species may vary signal structure with changes in climate over space or time. In particular, signals of lower frequency, narrower bandwidth, and longer duration should be more detectable in environments with high sound absorption. Using both North American wood warblers (Parulidae) and bats of the American Southwest, this work found evidence of associations between signal structure and sound absorption. Warbler species with higher mean absorption across their range were more likely to have narrow bandwidth songs. Bat species found in higher absorption habitats were more likely to have lower frequency echolocation calls. In addition, bat species changed echolocation call structure across seasons, using longer duration, lower frequency calls in the higher absorption rainy season. These results suggest that signals may diverge along climatic gradients due to variation in sound absorption, although the effects of absorption are modest. © 2012 Acoustical Society of America

Converting a Monopole Emission into a Dipole Using a Subwavelength Structure

NASA Astrophysics Data System (ADS)

Fan, Xu-Dong; Zhu, Yi-Fan; Liang, Bin; Cheng, Jian-chun; Zhang, Likun

2018-03-01

High-efficiency emission of multipoles is unachievable by a source much smaller than the wavelength, preventing compact acoustic devices for generating directional sound beams. Here, we present a primary scheme towards solving this problem by numerically and experimentally enclosing a monopole sound source in a structure with a dimension of around 1 /10 sound wavelength to emit a dipolar field. The radiated sound power is found to be more than twice that of a bare dipole. Our study of efficient emission of directional low-frequency sound from a monopole source in a subwavelength space may have applications such as focused ultrasound for imaging, directional underwater sound beams, miniaturized sonar, etc.

Bionic Modeling of Knowledge-Based Guidance in Automated Underwater Vehicles.

DTIC Science & Technology

1987-06-24

bugs and their foraging movements are heard by the sound of rustling leaves or rhythmic wing beats . ASYMMETRY OF EARS The faces of owls have captured...sound source without moving. The barn owl has binaural and monaural cues as well as cues that operate in relative motion when either the target or the...owl moves. Table 1 lists the cues. 7 TM No. 87- 2068 fTable 1. Sound Localization Parameters Used by the Barn Owl I BINAURAL PARAMETERS: 1. the

A higher-order split-step Fourier parabolic-equation sound propagation solution scheme.

PubMed

Lin, Ying-Tsong; Duda, Timothy F

2012-08-01

A three-dimensional Cartesian parabolic-equation model with a higher-order approximation to the square-root Helmholtz operator is presented for simulating underwater sound propagation in ocean waveguides. The higher-order approximation includes cross terms with the free-space square-root Helmholtz operator and the medium phase speed anomaly. It can be implemented with a split-step Fourier algorithm to solve for sound pressure in the model. Two idealized ocean waveguide examples are presented to demonstrate the performance of this numerical technique.

Liquid mercury sound velocity measurements under high pressure and high temperature by picosecond acoustics in a diamond anvils cell

NASA Astrophysics Data System (ADS)

Decremps, F.; Belliard, L.; Couzinet, B.; Vincent, S.; Munsch, P.; Le Marchand, G.; Perrin, B.

2009-07-01

Recent improvements to measure ultrasonic sound velocities of liquids under extreme conditions are described. Principle and feasibility of picosecond acoustics in liquids embedded in a diamond anvils cell are given. To illustrate the capability of these advances in the sound velocity measurement technique, original high pressure and high temperature results on the sound velocity of liquid mercury up to 5 GPa and 575 K are given. This high pressure technique will certainly be useful in several fundamental and applied problems in physics and many other fields such as geophysics, nonlinear acoustics, underwater sound, petrology or physical acoustics.

Soundscapes and Larval Settlement: Larval Bivalve Responses to Habitat-Associated Underwater Sounds.

PubMed

Eggleston, David B; Lillis, Ashlee; Bohnenstiehl, DelWayne R

2016-01-01

We quantified the effects of habitat-associated sounds on the settlement response of two species of bivalves with contrasting habitat preferences: (1) Crassostrea virginicia (oyster), which prefers to settle on other oysters, and (2) Mercenaria mercenaria (clam), which settles on unstructured habitats. Oyster larval settlement in the laboratory was significantly higher when exposed to oyster reef sound compared with either off-reef or no-sound treatments. Clam larval settlement did not vary according to sound treatments. Similar to laboratory results, field experiments showed that oyster larval settlement in "larval housings" suspended above oyster reefs was significantly higher compared with off-reef sites.

A Review: Characteristics of Noise Absorption Material

NASA Astrophysics Data System (ADS)

Amares, S.; Sujatmika, E.; Hong, T. W.; Durairaj, R.; Hamid, H. S. H. B.

2017-10-01

Noise is always treated as a nuisance to human and even noise pollution appears in the environmental causing discomfort. This also concerns the engineering design that tends to cultivate this noise propagation. Solution such as using material to absorb the sound have been widely used. The fundamental of the sound absorbing propagation, sound absorbing characteristics and its factors are minimally debated. Furthermore, the method in order to pertain sound absorbing related to the sound absorption coefficient is also limited, as many studies only contributes in result basis and very little in literature aspect. This paper revolves in providing better insight on the importance of sound absorption and the materials factors in obtaining the sound absorption coefficient.

Possible impact of global warming and ocean acidification on underwater sound in northern oceans: another perfect storm

NASA Astrophysics Data System (ADS)

Browning, David

2011-04-01

The greatest ocean pH change, which will result in lower low frequency sound attenuation, is predicted for higher latitudes. Here shallow sound channel axies exist, allowing the impact on sound to be seen sooner and also more extensively since the principal propagation paths will be near the surface. However, at the same time, higher wind speeds and greater ice breakup,as well as increased ship traffic, could result in higher noise levels. Marine mammals in this environment may have, on one hand, improving communication conditions but also the possibility of increased background noise.

Underwater Intruder Detection Sonar for Harbour Protection: State of the Art Review and Implications

DTIC Science & Technology

2006-10-01

intruder would appear as a small moving “ blob ” of energetic echo in the echograph, and the operator could judge whether the contact is a threat that calls...visually then as a small fluctuating “ blob ” against a fluctuating background of sound clutter and reverberation, making it difficult to visually...4. Non-random false alarms caused by genuine underwater contacts that happened not to be intruders—by large fish , or schools of fish , or marine

Extensible 3D (X3D) Graphics for Visualizing Marine Mammal Reaction to Underwater Sound on the Southern California ASW Range (SOAR)

DTIC Science & Technology

2007-06-01

file ARC- 20060811T130816.txt, where color is used to represent points in time (red being the earliest, transitioning to orange, yellow , then white...Administration (NOAA), using passive hydrophone arrays along the mid-Atlantic ridge to listen for underwater earthquakes and volcanoes , have found that a...appeared. The earliest data points were designated red, and later points were shades of orange and yellow , until the last points (relative to the

Cell openness manipulation of low density polyurethane foam for efficient sound absorption

NASA Astrophysics Data System (ADS)

Hyuk Park, Ju; Suh Minn, Kyung; Rae Lee, Hyeong; Hyun Yang, Sei; Bin Yu, Cheng; Yeol Pak, Seong; Sung Oh, Chi; Seok Song, Young; June Kang, Yeon; Ryoun Youn, Jae

2017-10-01

Satisfactory sound absorption using a low mass density foam is an intriguing desire for achieving high fuel efficiency of vehicles. This issue has been dealt with a microcellular geometry manipulation. In this study, we demonstrate the relationship between cell openness of polyurethane (PU) foam and sound absorption behaviors, both theoretically and experimentally. The objective of this work is to mitigate a threshold of mass density by rendering a sound absorber which shows a satisfactory performance. The cell openness, which causes the best sound absorption performance in all cases considered, was estimated as 15% by numerical simulation. Cell openness of PU foam was experimentally manipulated into desired ranges by adjusting rheological properties in a foaming reaction. Microcellular structures of the fabricated PU foams were observed and sound absorption coefficients were measured using a B&K impedance tube. The fabricated PU foam with the best cell openness showed better sound absorption performance than the foam with double mass density. We envisage that this study can help the manufacture of low mass density sound absorbing foams more efficiently and economically.

Structural parameter effect of porous material on sound absorption performance of double-resonance material

NASA Astrophysics Data System (ADS)

Fan, C.; Tian, Y.; Wang, Z. Q.; Nie, J. K.; Wang, G. K.; Liu, X. S.

2017-06-01

In view of the noise feature and service environment of urban power substations, this paper explores the idea of compound impedance, fills some porous sound-absorption material in the first resonance cavity of the double-resonance sound-absorption material, and designs a new-type of composite acoustic board. We conduct some acoustic characterizations according to the standard test of impedance tube, and research on the influence of assembly order, the thickness and area density of the filling material, and back cavity on material sound-absorption performance. The results show that the new-type of acoustic board consisting of aluminum fibrous material as inner structure, micro-porous board as outer structure, and polyester-filled space between them, has good sound-absorption performance for low frequency and full frequency noise. When the thickness, area density of filling material and thickness of back cavity increase, the sound absorption coefficient curve peak will move toward low frequency.

Reduction of the Radiating Sound of a Submerged Finite Cylindrical Shell Structure by Active Vibration Control

PubMed Central

Kim, Heung Soo; Sohn, Jung Woo; Jeon, Juncheol; Choi, Seung-Bok

2013-01-01

In this work, active vibration control of an underwater cylindrical shell structure was investigated, to suppress structural vibration and structure-borne noise in water. Finite element modeling of the submerged cylindrical shell structure was developed, and experimentally evaluated. Modal reduction was conducted to obtain the reduced system equation for the active feedback control algorithm. Three Macro Fiber Composites (MFCs) were used as actuators and sensors. One MFC was used as an exciter. The optimum control algorithm was designed based on the reduced system equations. The active control performance was then evaluated using the lab scale underwater cylindrical shell structure. Structural vibration and structure-borne noise of the underwater cylindrical shell structure were reduced significantly by activating the optimal controller associated with the MFC actuators. The results provide that active vibration control of the underwater structure is a useful means to reduce structure-borne noise in water. PMID:23389344

Reduction of the radiating sound of a submerged finite cylindrical shell structure by active vibration control.

PubMed

Kim, Heung Soo; Sohn, Jung Woo; Jeon, Juncheol; Choi, Seung-Bok

2013-02-06

In this work, active vibration control of an underwater cylindrical shell structure was investigated, to suppress structural vibration and structure-borne noise in water. Finite element modeling of the submerged cylindrical shell structure was developed, and experimentally evaluated. Modal reduction was conducted to obtain the reduced system equation for the active feedback control algorithm. Three Macro Fiber Composites (MFCs) were used as actuators and sensors. One MFC was used as an exciter. The optimum control algorithm was designed based on the reduced system equations. The active control performance was then evaluated using the lab scale underwater cylindrical shell structure. Structural vibration and structure-borne noise of the underwater cylindrical shell structure were reduced significantly by activating the optimal controller associated with the MFC actuators. The results provide that active vibration control of the underwater structure is a useful means to reduce structure-borne noise in water.

A study of sound absorption by street canyon boundaries and asphalt rubber concrete pavement

NASA Astrophysics Data System (ADS)

Drysdale, Graeme Robert

A sound field model, based on a classical diffusion equation, is extended to account for sound absorption in a diffusion parameter used to model sound energy in a narrow street canyon. The model accounts for a single sound absorption coefficient, separate accommodation coefficients and a combination of separate absorption and accommodation coefficients from parallel canyon walls. The new expressions are compared to the original formula through numerical simulations to reveal the effect of absorption on sound diffusion. The newly established analytical formulae demonstrate satisfactory agreement with their predecessor under perfect reflection. As well, the influence of the extended diffusion parameter on normalized sound pressure levels in a narrow street canyon is in agreement with experimental data. The diffusion parameters are used to model sound energy density in a street canyon as a function of the sound absorption coefficient of the street canyon walls. The acoustic and material properties of conventional and asphalt rubber concrete (ARC) pavement are also studied to assess how the crumb rubber content influences sound absorption in street canyons. The porosity and absolute permeability of compacted specimens of asphalt rubber concrete are measured and compared to their normal and random incidence sound absorption coefficients as a function of crumb rubber content in the modified binder. Nonlinear trends are found between the sound absorption coefficients, porosity and absolute permeability of the compacted specimens and the percentage of crumb rubber in the modified binders. The cross-sectional areas of the air voids on the surfaces of the compacted specimens are measured using digital image processing techniques and a linear relationship is obtained between the average void area and crumb rubber content. The measured material properties are used to construct an empirical formula relating the average porosity, normal incidence noise reduction coefficients and percentage of crumb rubber in the modified binder of the compacted specimens.

Hearing and Underwater Noise Exposure

DTIC Science & Technology

1985-08-27

Ordnance Laboratory, White Oak, Silver Springs, Md. Corso, J. F. (1963) Bone-conduction thresholds for sonic and ultrasonic frequencies. J. Acoust...Soc. Am. 35, 1738-1743. Corso, J. F., & Levine, M. (1965a) Sonic and Ultrasonic equal loudness contours. J. Exp. Psychol. 70, 412-416. Corso, J...KEY WORDS (Continue on reverse aide II neceaaary and identity by block number) Hearing, Deafness, Sonar, Noise, Sound, Ultrasound, Infra -sound

Sound absorption study on acoustic panel from kapok fiber and egg tray

NASA Astrophysics Data System (ADS)

Kaamin, Masiri; Mahir, Nurul Syazwani Mohd; Kadir, Aslila Abd; Hamid, Nor Baizura; Mokhtar, Mardiha; Ngadiman, Norhayati

2017-12-01

Noise also known as a sound, especially one that is loud or unpleasant or that causes disruption. The level of noise can be reduced by using sound absorption panel. Currently, the market produces sound absorption panel, which use synthetic fibers that can cause harmful effects to the health of consumers. An awareness of using natural fibers from natural materials gets attention of some parties to use it as a sound absorbing material. Therefore, this study was conducted to investigate the potential of sound absorption panel using egg trays and kapok fibers. The test involved in this study was impedance tube test which aims to get sound absorption coefficient (SAC). The results showed that there was good sound absorption at low frequency from 0 Hz up to 900 Hz where the maximum absorption coefficient was 0.950 while the maximum absorption at high frequencies was 0.799. Through the noise reduction coefficient (NRC), the material produced NRC of 0.57 indicates that the materials are very absorbing. In addition, the reverberation room test was carried out to get the value of reverberation time (RT) in unit seconds. Overall this panel showed good results at low frequencies between 0 Hz up to 1500 Hz. In that range of frequency, the maximum reverberation time for the panel was 3.784 seconds compared to the maximum reverberation time for an empty room was 5.798 seconds. This study indicated that kapok fiber and egg tray as the material of absorption panel has a potential as environmental and cheap products in absorbing sound at low frequency.

Pavement sound absorption measurements in the U.S.

DOT National Transportation Integrated Search

2012-08-19

In the U.S., the topic of pavement sound absorption in regard to tire-pavement noise has shown increased interest and research over the last several years. Four types of pavement sound absorption measurements with various applications are discussed: ...

An Underwater Color Image Quality Evaluation Metric.

PubMed

Yang, Miao; Sowmya, Arcot

2015-12-01

Quality evaluation of underwater images is a key goal of underwater video image retrieval and intelligent processing. To date, no metric has been proposed for underwater color image quality evaluation (UCIQE). The special absorption and scattering characteristics of the water medium do not allow direct application of natural color image quality metrics especially to different underwater environments. In this paper, subjective testing for underwater image quality has been organized. The statistical distribution of the underwater image pixels in the CIELab color space related to subjective evaluation indicates the sharpness and colorful factors correlate well with subjective image quality perception. Based on these, a new UCIQE metric, which is a linear combination of chroma, saturation, and contrast, is proposed to quantify the non-uniform color cast, blurring, and low-contrast that characterize underwater engineering and monitoring images. Experiments are conducted to illustrate the performance of the proposed UCIQE metric and its capability to measure the underwater image enhancement results. They show that the proposed metric has comparable performance to the leading natural color image quality metrics and the underwater grayscale image quality metrics available in the literature, and can predict with higher accuracy the relative amount of degradation with similar image content in underwater environments. Importantly, UCIQE is a simple and fast solution for real-time underwater video processing. The effectiveness of the presented measure is also demonstrated by subjective evaluation. The results show better correlation between the UCIQE and the subjective mean opinion score.

Sound absorption and morphology characteristic of porous concrete paving blocks

NASA Astrophysics Data System (ADS)

Halim, N. H. Abd; Nor, H. Md; Ramadhansyah, P. J.; Mohamed, A.; Hassan, N. Abdul; Ibrahim, M. H. Wan; Ramli, N. I.; Nazri, F. Mohamed

2017-11-01

In this study, sound absorption and morphology characteristic of Porous Concrete Paving Blocks (PCPB) at different sizes of coarse aggregate were presented. Three different sizes of coarse aggregate were used; passing 10 mm retained 5 mm (as Control), passing 8 mm retained 5 mm (8 - 5) and passing 10 mm retained 8 mm (10 - 8). The sound absorption test was conducted through the impedance tube at different frequency. It was found that the size of coarse aggregate affects the level of absorption of the specimens. It also shows that PCPB 10 - 8 resulted in high sound absorption compared to the other blocks. On the other hand, microstructure morphology of PCPB shows a clearer version of existing micro-cracks and voids inside the specimens which affecting the results of sound absorption.

Optimization of decoupling performance of underwater acoustic coating with cavities via equivalent fluid model

NASA Astrophysics Data System (ADS)

Huang, Lingzhi; Xiao, Yong; Wen, Jihong; Zhang, Hao; Wen, Xisen

2018-07-01

Acoustic coatings with periodically arranged internal cavities have been successfully applied in submarines for the purpose of decoupling water from vibration of underwater structures, and thus reducing underwater sound radiation. Previous publications on decoupling acoustic coatings with cavities are mainly focused on the case of coatings with specific shaped cavities, including cylindrical and conical cavities. To explore better decoupling performance, an optimal design of acoustic coating with complex shaped cavities is attempted in this paper. An equivalent fluid model is proposed to characterize coatings with general axisymmetrical cavities. By employing the equivalent fluid model, an analytical vibroacoustic model is further developed for the prediction of sound radiation from an infinite plate covered with an equivalent fluid layer (as a replacement of original coating) and immersed in water. Numerical examples are provided to verify the equivalent fluid model. Based on a combining use of the analytical vibroacoustic model and a differential evolution algorithm, optimal designs for acoustic coatings with cavities are conducted. Numerical results demonstrate that the decoupling performance of acoustic coating can be significantly improved by employing special axisymmetrical cavities as compared to traditional cylindrical cavities.

Great cormorants ( Phalacrocorax carbo) can detect auditory cues while diving

NASA Astrophysics Data System (ADS)

Hansen, Kirstin Anderson; Maxwell, Alyssa; Siebert, Ursula; Larsen, Ole Næsbye; Wahlberg, Magnus

2017-06-01

In-air hearing in birds has been thoroughly investigated. Sound provides birds with auditory information for species and individual recognition from their complex vocalizations, as well as cues while foraging and for avoiding predators. Some 10% of existing species of birds obtain their food under the water surface. Whether some of these birds make use of acoustic cues while underwater is unknown. An interesting species in this respect is the great cormorant ( Phalacrocorax carbo), being one of the most effective marine predators and relying on the aquatic environment for food year round. Here, its underwater hearing abilities were investigated using psychophysics, where the bird learned to detect the presence or absence of a tone while submerged. The greatest sensitivity was found at 2 kHz, with an underwater hearing threshold of 71 dB re 1 μPa rms. The great cormorant is better at hearing underwater than expected, and the hearing thresholds are comparable to seals and toothed whales in the frequency band 1-4 kHz. This opens up the possibility of cormorants and other aquatic birds having special adaptations for underwater hearing and making use of underwater acoustic cues from, e.g., conspecifics, their surroundings, as well as prey and predators.

Study of archaeological underwater finds: deterioration and conservation

NASA Astrophysics Data System (ADS)

Crisci, G. M.; La Russa, M. F.; Macchione, M.; Malagodi, M.; Palermo, A. M.; Ruffolo, S. A.

2010-09-01

This study is aimed at an assessment of the methodologies, instruments and new applications for underwater archaeology. Research focused on study of the various kinds of degradation affecting underwater finds and stone materials aged in underwater environment, efficiency evaluation of various surface cleaning methods and study and mixing of protective products with consolidating resins and antimicrobial biocides to be applied to restored underwater finds. Transmitted light optical microscopy and scanning electron microscopy (SEM) were used to study surface biofilms and the interactions with samples of different stone materials such as brick, marble and granite immersed in the submarine archaeological area of Crotone (South of Italy). Surface cleaning tests were performed with application of ion exchange resins, EDTA, hydrogen peroxide and ultrasound techniques. Capillary water absorption, simulated solar ageing and colourimetric measurements were carried out to evaluate hydrophobic and consolidant properties; to assess biocidal efficacy, heterotrophic micro-organisms ( Aspergillus niger) were inoculated on agar plates and growth inhibition was measured.

Geographic variation and acoustic structure of the underwater vocalization of harbor seal (Phoca vitulina) in Norway, Sweden and Scotland.

PubMed

Bjørgesaeter, Anders; Ugland, Karl Inne; Bjørge, Arne

2004-10-01

The male harbor seal (Phoca vitulina) produces broadband nonharmonic vocalizations underwater during the breeding season. In total, 120 vocalizations from six colonies were analyzed to provide a description of the acoustic structure and for the presence of geographic variation. The complex harbor seal vocalizations may be described by how the frequency bandwidth varies over time. An algorithm that identifies the boundaries between noise and signal from digital spectrograms was developed in order to extract a frequency bandwidth contour. The contours were used as inputs for multivariate analysis. The vocalizations' sound types (e.g., pulsed sound, whistle, and broadband nonharmonic sound) were determined by comparing the vocalizations' spectrographic representations with sound waves produced by known sound sources. Comparison between colonies revealed differences in the frequency contours, as well as some geographical variation in use of sound types. The vocal differences may reflect a limited exchange of individuals between the six colonies due to long distances and strong site fidelity. Geographically different vocal repertoires have potential for identifying discrete breeding colonies of harbor seals, but more information is needed on the nature and extent of early movements of young, the degree of learning, and the stability of the vocal repertoire. A characteristic feature of many vocalizations in this study was the presence of tonal-like introductory phrases that fit into the categories pulsed sound and whistles. The functions of these phrases are unknown but may be important in distance perception and localization of the sound source. The potential behavioral consequences of the observed variability may be indicative of adaptations to different environmental properties influencing determination of distance and direction and plausible different male mating tactics.

Mapping the sound field of an erupting submarine volcano using an acoustic glider.

PubMed

Matsumoto, Haru; Haxel, Joseph H; Dziak, Robert P; Bohnenstiehl, Delwayne R; Embley, Robert W

2011-03-01

An underwater glider with an acoustic data logger flew toward a recently discovered erupting submarine volcano in the northern Lau basin. With the volcano providing a wide-band sound source, recordings from the two-day survey produced a two-dimensional sound level map spanning 1 km (depth) × 40 km(distance). The observed sound field shows depth- and range-dependence, with the first-order spatial pattern being consistent with the predictions of a range-dependent propagation model. The results allow constraining the acoustic source level of the volcanic activity and suggest that the glider provides an effective platform for monitoring natural and anthropogenic ocean sounds. © 2011 Acoustical Society of America

A practical weighting function for harbor porpoise underwater sound level measurements.

PubMed

Terhune, John M

2013-09-01

Harbor porpoise (Phocoena phocoena) are subject to underwater noise disturbance from anthropogenic sources, especially shipping. The underwater audiograms of harbor porpoise were used to create a frequency weighting function, dBht(Phocoena phocoena), to permit estimation of the broadband perceived amplitudes of ambient and shipping noise. An equation was fit to the 0.02-20 kHz range of unmasked detection thresholds and normalizing to 0 dB at 20 kHz; dB = 46.4-35.6 log(kHz). The weighting function de-emphasizes the low frequency components of noise. Harbor porpoise hearing is less sensitive to low frequency shipping noise and, except at high amplitudes, estimating potential noise impacts using linear measurements will be misleading.

Dolphin Sounds-Inspired Covert Underwater Acoustic Communication and Micro-Modem

PubMed Central

Qiao, Gang; Liu, Songzuo; Bilal, Muhammad

2017-01-01

A novel portable underwater acoustic modem is proposed in this paper for covert communication between divers or underwater unmanned vehicles (UUVs) and divers at a short distance. For the first time, real dolphin calls are used in the modem to realize biologically inspired Covert Underwater Acoustic Communication (CUAC). A variety of dolphin whistles and clicks stored in an SD card inside the modem helps to realize different biomimetic CUAC algorithms based on the specified covert scenario. In this paper, the information is conveyed during the time interval between dolphin clicks. TMS320C6748 and TLV320AIC3106 are the core processors used in our unique modem for fast digital processing and interconnection with other terminals or sensors. Simulation results show that the bit error rate (BER) of the CUAC algorithm is less than 10−5 when the signal to noise ratio is over ‒5 dB. The modem was tested in an underwater pool, and a data rate of 27.1 bits per second at a distance of 10 m was achieved. PMID:29068363

Characterization of the MEMS Directional Sound Sensor Fabricated Using the SOIMUMPS Process

DTIC Science & Technology

2008-06-01

ABBREVIATIONS AND ACRONYMS ASW Anti- Submarine Warfare AUV Autonomous Underwater Vehicle DRIE Deep Reactive Ion Etching FAS Federation of American...as the frequency diverges from the resonant frequency (2980 Hz ) of the sensor. This analysis points out some disadvantages of the current set up of...sound sensor has important military applications, in particular to anti- submarine warfare (ASW). The sensor considered in this thesis is modeled on

Experimentally-Based Ocean Acoustic Propagation and Coherence Studies

DTIC Science & Technology

2013-09-30

degradation and/or exploitation of available sonic information. OBJECTIVES An objective is to quantify and explain underwater sound fluctuation...focusing did not entirely match the data because of terrain uncertainty. The paper further notes that a rapid drop-off of received sound level from the...covariance functions of complex demodulated signals. The array gain is defined as the signal to noise ratio for coherently added (beam steered) acoustic

Hybrid local piezoelectric and conductive functions for high performance airborne sound absorption

NASA Astrophysics Data System (ADS)

Rahimabady, Mojtaba; Statharas, Eleftherios Christos; Yao, Kui; Sharifzadeh Mirshekarloo, Meysam; Chen, Shuting; Tay, Francis Eng Hock

2017-12-01

A concept of hybrid local piezoelectric and electrical conductive functions for improving airborne sound absorption is proposed and demonstrated in composite foam made of porous polar polyvinylidene fluoride (PVDF) mixed with conductive single-walled carbon nanotube (SWCNT). According to our hybrid material function design, the local piezoelectric effect in the PVDF matrix with the polar structure and the electrical resistive loss of SWCNT enhanced sound energy conversion to electrical energy and subsequently to thermal energy, respectively, in addition to the other known sound absorption mechanisms in a porous material. It is found that the overall energy conversion and hence the sound absorption performance are maximized when the concentration of the SWCNT is around the conductivity percolation threshold. For the optimal composition of PVDF/5 wt. % SWCNT, a sound reduction coefficient of larger than 0.58 has been obtained, with a high sound absorption coefficient higher than 50% at 600 Hz, showing their great values for passive noise mitigation even at a low frequency.

Sound absorption of textile material using a microfibres resistive layer

NASA Astrophysics Data System (ADS)

Segura Alcaraz, M. P.; Bonet-Aracil, M.; Segura Alcaraz, J. G.; Montava Seguí, I.

2017-10-01

Acoustic comfort is a basic human need. One of the adverse effects of noise is its interference with speech discrimination. Textile materials are suitable to be used as sound absorptive materials and thus help to improve acoustic comfort in rooms. Micro-fibre fabrics can be considered as better sound absorbers than regular fibre fabrics mainly due to the higher surface of its fibres and bigger contact area with the air thus, allowing greater dissipation of sound energy. In this work, the use of a microfibre woven fabric as an upstream layer is analysed considering acoustic issues. Authors demonstrate it improves the sound absorption of a polyester nonwoven, resulting in a material suitable for absorption at the sound frequencies of the human voice.

Sound pressure level gain in an acoustic metamaterial cavity.

PubMed

Song, Kyungjun; Kim, Kiwon; Hur, Shin; Kwak, Jun-Hyuk; Park, Jihyun; Yoon, Jong Rak; Kim, Jedo

2014-12-11

The inherent attenuation of a homogeneous viscous medium limits radiation propagation, thereby restricting the use of many high-frequency acoustic devices to only short-range applications. Here, we design and experimentally demonstrate an acoustic metamaterial localization cavity which is used for sound pressure level (SPL) gain using double coiled up space like structures thereby increasing the range of detection. This unique behavior occurs within a subwavelength cavity that is 1/10(th) of the wavelength of the incident acoustic wave, which provides up to a 13 dB SPL gain. We show that the amplification results from the Fabry-Perot resonance of the cavity, which has a simultaneously high effective refractive index and effective impedance. We also experimentally verify the SPL amplification in an underwater environment at higher frequencies using a sample with an identical unit cell size. The versatile scalability of the design shows promising applications in many areas, especially in acoustic imaging and underwater communication.

Sound absorption coefficient of coal bottom ash concrete for railway application

NASA Astrophysics Data System (ADS)

Ramzi Hannan, N. I. R.; Shahidan, S.; Maarof, Z.; Ali, N.; Abdullah, S. R.; Ibrahim, M. H. Wan

2017-11-01

A porous concrete able to reduce the sound wave that pass through it. When a sound waves strike a material, a portion of the sound energy was reflected back and another portion of the sound energy was absorbed by the material while the rest was transmitted. The larger portion of the sound wave being absorbed, the lower the noise level able to be lowered. This study is to investigate the sound absorption coefficient of coal bottom ash (CBA) concrete compared to the sound absorption coefficient of normal concrete by carried out the impedance tube test. Hence, this paper presents the result of the impedance tube test of the CBA concrete and normal concrete.

Preliminary laboratory testing on the sound absorption of coupled cavity sonic crystal

NASA Astrophysics Data System (ADS)

Kristiani, R.; Yahya, I.; Harjana; Suparmi

2016-11-01

This paper focuses on the sound absorption performance of coupled cavity sonic crystal. It constructed by a pair of a cylindrical tube with different values in diameters. A laboratory test procedure after ASTM E1050 has been conducted to measure the sound absorption of the sonic crystal elements. The test procedures were implemented to a single coupled scatterer and also to a pair of similar structure. The results showed that using the paired structure bring a better possibility for increase the sound absorption to a wider absorption range. It also bring a practical advantage for setting the local Helmholtz resonant frequency to certain intended frequency.

The contribution of molecular relaxation in nitrogen to the absorption of sound in the atmosphere

NASA Technical Reports Server (NTRS)

Zuckerwar, A. J.; Meredith, R. W.

1980-01-01

Results and statistical analysis are presented for sound absorption in N2-H2O binary mixtures at room temperature. Experimental procedure, temperature effects, and preliminary results are presented for sound absorption in N2-H2O binary mixtures at elevated temperatures.

Time-of-flight range imaging for underwater applications

NASA Astrophysics Data System (ADS)

Merbold, Hannes; Catregn, Gion-Pol; Leutenegger, Tobias

2018-02-01

Precise and low-cost range imaging in underwater settings with object distances on the meter level is demonstrated. This is addressed through silicon-based time-of-flight (TOF) cameras operated with light emitting diodes (LEDs) at visible, rather than near-IR wavelengths. We find that the attainable performance depends on a variety of parameters, such as the wavelength dependent absorption of water, the emitted optical power and response times of the LEDs, or the spectral sensitivity of the TOF chip. An in-depth analysis of the interplay between the different parameters is given and the performance of underwater TOF imaging using different visible illumination wavelengths is analyzed.

Sonar Performance Estimation Model with Seismo-Acoustic Effects on Underwater Sound Propagation

DTIC Science & Technology

1989-06-27

properties of 12 the bottom sediments. The ray theory is highly satisfactory to predict and explain some electromagnetic phenomena, and it is very useful in...erroneous transmission loss computations where acoustic interference occurs. However, his transmission loss calculations are made using ray theory which is...developed which treat some of these properties. Each model has its virtues and limitations. For high- frequency sound propagation the ray theory can

Effect of Internal Solitary Waves on Underwater Acoustic Propagation

DTIC Science & Technology

2010-01-01

and 760 m from an expendable bathyther- mograph and one temperature profile below 760 m from the Navy’s Gen- eralized Digital Environment Model ( GDEM ...To calculate sound speed, the GDEM (average of July and August) salinity profile (nearest to CMB) was used. The sound speeds calculated from the GDEM ...from the GDEM sa- linity profile and 424 temperature pro- files generated the range-dependent SSPs (Figure 6). Comparison of the acoustic propagation

Ambient Noise in the Sea

DTIC Science & Technology

1984-01-01

the 14 to 222 Hz band. In a tank, the echolocation signals made by dolphins were found (167) to be directional, with peak energies above 100 kHz...17. Daniels, F. B., Mechanisms of Generation of Infrasound by Ocean Waves, JASA 24, 83, 1952. 18. Daniels, F. B., Generation of Infrasound by Ocean...in the Ocean by Surface Waves, J. Sound and Vibration 37, 185, 1974. 58. Hughes, B., Estimates of Underwater Sound (and Infrasound ) Produced by Non

A Synopsis of Marine Animal Underwater Sounds in Eight Geographic Areas

DTIC Science & Technology

1971-05-28

MAMMALS (1) HIGHEST PROBABILITY Delphinapterus leucas - In Apr.-June they move up Kola River. Present all months except July) Aug, Sept...its vocali- zations are available from Dr. W. C. Cummings, NUC Code 5054. : ii V, , 71 Delphinapterus leucas --(white-whale or beluga) The beluga is...about 5 msoc. ~7 * Delphinapterus leucas --(white whale or beluga-continued Our own estimates of source level for sounds from an individual whale 2 are

Hearing in cetaceans: from natural history to experimental biology.

PubMed

Mooney, T Aran; Yamato, Maya; Branstetter, Brian K

2012-01-01

Sound is a primary sensory cue for most marine mammals, and this is especially true for cetaceans. To passively and actively acquire information about their environment, cetaceans have some of the most derived ears of all mammals, capable of sophisticated, sensitive hearing and auditory processing. These capabilities have developed for survival in an underwater world where sound travels five times faster than in air, and where light is quickly attenuated and often limited at depth, at night, and in murky waters. Cetacean auditory evolution has capitalized on the ubiquity of sound cues and the efficiency of underwater acoustic communication. The sense of hearing is central to cetacean sensory ecology, enabling vital behaviours such as locating prey, detecting predators, identifying conspecifics, and navigating. Increasing levels of anthropogenic ocean noise appears to influence many of these activities. Here, we describe the historical progress of investigations on cetacean hearing, with a particular focus on odontocetes and recent advancements. While this broad topic has been studied for several centuries, new technologies in the past two decades have been leveraged to improve our understanding of a wide range of taxa, including some of the most elusive species. This chapter addresses topics including how sounds are received, what sounds are detected, hearing mechanisms for complex acoustic scenes, recent anatomical and physiological studies, the potential impacts of noise, and mysticete hearing. We conclude by identifying emerging research topics and areas which require greater focus. Copyright © 2012 Elsevier Ltd. All rights reserved.

Laboratory investigation on the role of tubular shaped micro resonators phononic crystal insertion on the absorption coefficient of profiled sound absorber

NASA Astrophysics Data System (ADS)

Yahya, I.; Kusuma, J. I.; Harjana; Kristiani, R.; Hanina, R.

2016-02-01

This paper emphasizes the influence of tubular shaped microresonators phononic crystal insertion on the sound absorption coefficient of profiled sound absorber. A simple cubic and two different bodies centered cubic phononic crystal lattice model were analyzed in a laboratory test procedure. The experiment was conducted by using transfer function based two microphone impedance tube method refer to ASTM E-1050-98. The results show that sound absorption coefficient increase significantly at the mid and high-frequency band (600 - 700 Hz) and (1 - 1.6 kHz) when tubular shaped microresonator phononic crystal inserted into the tested sound absorber element. The increment phenomena related to multi-resonance effect that occurs when sound waves propagate through the phononic crystal lattice model that produce multiple reflections and scattering in mid and high-frequency band which increases the sound absorption coefficient accordingly

Experimental study on the sound absorption characteristics of continuously graded phononic crystals

NASA Astrophysics Data System (ADS)

Zhang, X. H.; Qu, Z. G.; He, X. C.; Lu, D. L.

2016-10-01

Novel three-dimensional (3D) continuously graded phononic crystals (CGPCs) have been designed, and fabricated by 3D printing. Each of the CGPCs is an entity instead of a combination of several other samples, and the porosity distribution of the CGPC along the incident direction is nearly linear. The sound absorption characteristics of CGPCs were experimentally investigated and compared with those of uniform phononic crystals (UPCs) and discretely stepped phononic crystals (DSPCs). Experimental results show that CGPCs demonstrate excellent sound absorption performance because of their continuously graded structures. CGPCs have higher sound absorption coefficients in the large frequency range and more sound absorption coefficient peaks in a specific frequency range than UPCs and DSPCs. In particular, the sound absorption coefficients of the CGPC with a porosity of 0.6 and thickness of 30 mm are higher than 0.56 when the frequency is 1350-6300 Hz and are all higher than 0.2 in the studied frequency range (1000-6300 Hz). CGPCs are expected to have potential application in noise control, especially in the broad frequency and low-frequency ranges.

Underwater Hearing in Turtles.

PubMed

Willis, Katie L

2016-01-01

The hearing of turtles is poorly understood compared with the other reptiles. Although the mechanism of transduction of sound into a neural signal via hair cells has been described in detail, the rest of the auditory system is largely a black box. What is known is that turtles have higher hearing thresholds than other reptiles, with best frequencies around 500 Hz. They also have lower underwater hearing thresholds than those in air, owing to resonance of the middle ear cavity. Further studies demonstrated that all families of turtles and tortoises share a common middle ear cavity morphology, with scaling best suited to underwater hearing. This supports an aquatic origin of the group. Because turtles hear best under water, it is important to examine their vulnerability to anthropogenic noise. However, the lack of basic data makes such experiments difficult because only a few species of turtles have published audiograms. There are also almost no behavioral data available (understandable due to training difficulties). Finally, few studies show what kinds of sounds are behaviorally relevant. One notable paper revealed that the Australian snake-necked turtle (Chelodina oblonga) has a vocal repertoire in air, at the interface, and under water. Findings like these suggest that there is more to the turtle aquatic auditory scene than previously thought.

Experimental investigation of sound absorption of acoustic wedges for anechoic chambers

NASA Astrophysics Data System (ADS)

Belyaev, I. V.; Golubev, A. Yu.; Zverev, A. Ya.; Makashov, S. Yu.; Palchikovskiy, V. V.; Sobolev, A. F.; Chernykh, V. V.

2015-09-01

The results of measuring the sound absorption by acoustic wedges, which were performed in AC-3 and AC-11 reverberation chambers at the Central Aerohydrodynamic Institute (TsAGI), are presented. Wedges of different densities manufactured from superfine basaltic and thin mineral fibers were investigated. The results of tests of these wedges were compared to the sound absorption of wedges of the operating AC-2 anechoic facility at TsAGI. It is shown that basaltic-fiber wedges have better sound-absorption characteristics than the investigated analogs and can be recommended for facing anechoic facilities under construction.

Acoustic contributions of a sound absorbing blanket placed in a double panel structure: absorption versus transmission.

PubMed

Doutres, Olivier; Atalla, Noureddine

2010-08-01

The objective of this paper is to propose a simple tool to estimate the absorption vs. transmission loss contributions of a multilayered blanket unbounded in a double panel structure and thus guide its optimization. The normal incidence airborne sound transmission loss of the double panel structure, without structure-borne connections, is written in terms of three main contributions; (i) sound transmission loss of the panels, (ii) sound transmission loss of the blanket and (iii) sound absorption due to multiple reflections inside the cavity. The method is applied to four different blankets frequently used in automotive and aeronautic applications: a non-symmetric multilayer made of a screen in sandwich between two porous layers and three symmetric porous layers having different pore geometries. It is shown that the absorption behavior of the blanket controls the acoustic behavior of the treatment at low and medium frequencies and its transmission loss at high frequencies. Acoustic treatment having poor sound absorption behavior can affect the performance of the double panel structure.

Soundscapes and Larval Settlement: Characterizing the Stimulus from a Larval Perspective.

PubMed

Lillis, Ashlee; Eggleston, David B; Bohnenstiehl, DelWayne R

2016-01-01

There is growing evidence that underwater sounds serve as a cue for the larvae of marine organisms to locate suitable settlement habitats; however, the relevant spatiotemporal scales of variability in habitat-related sounds and how this variation scales with larval settlement processes remain largely uncharacterized, particularly in estuarine habitats. Here, we provide an overview of the approaches we have developed to characterize an estuarine soundscape as it relates to larval processes, and a conceptual framework is provided for how habitat-related sounds may influence larval settlement, using oyster reef soundscapes as an example.

75 FR 5575 - Taking and Importing Marine Mammals; Navy Training Activities Conducted in the Gulf of Alaska

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-03

... present in the area to sound from various active tactical sonar sources or to pressure from underwater... utilizing mid- and high frequency active sonar sources and explosive detonations. These sonar and explosive...

Underwater noise reduction of marine pile driving using a double pile.

DOT National Transportation Integrated Search

2015-12-01

Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. : It has been shown that current pile driving noise attenuation techniques, such as bubble curtains and : cofferdams, provide limited noise r...

Thin Fresnel zone plate lenses for focusing underwater sound

NASA Astrophysics Data System (ADS)

Calvo, David C.; Thangawng, Abel L.; Nicholas, Michael; Layman, Christopher N.

2015-07-01

A Fresnel zone plate (FZP) lens of the Soret type creates a focus by constructive interference of waves diffracted through open annular zones in an opaque screen. For underwater sound below MHz frequencies, a large FZP that blocks sound using high-impedance, dense materials would have practical disadvantages. We experimentally and numerically investigate an alternative approach of creating a FZP with thin (0.4λ) acoustically opaque zones made of soft silicone rubber foam attached to a thin (0.1λ) transparent rubber substrate. An ultra-thin (0.0068λ) FZP that achieves higher gain is also proposed and simulated which uses low-volume fraction, bubble-like resonant air ring cavities to construct opaque zones. Laboratory measurements at 200 kHz indicate that the rubber foam can be accurately modeled as a lossy fluid with an acoustic impedance approximately 1/10 that of water. Measured focal gains up to 20 dB agree with theoretical predictions for normal and oblique incidence. The measured focal radius of 0.68λ (peak-to-null) agrees with the Rayleigh diffraction limit prediction of 0.61 λ/NA (NA = 0.88) for a low-aberration lens.

Observations on abundance of bluntnose sixgill sharks, Hexanchus griseus, in an urban waterway in Puget Sound, 2003-2005.

PubMed

Griffing, Denise; Larson, Shawn; Hollander, Joel; Carpenter, Tim; Christiansen, Jeff; Doss, Charles

2014-01-01

The bluntnose sixgill shark, Hexanchus griseus, is a widely distributed but poorly understood large, apex predator. Anecdotal reports of diver-shark encounters in the late 1990's and early 2000's in the Pacific Northwest stimulated interest in the normally deep-dwelling shark and its presence in the shallow waters of Puget Sound. Analysis of underwater video documenting sharks at the Seattle Aquarium's sixgill research site in Elliott Bay and mark-resight techniques were used to answer research questions about abundance and seasonality. Seasonal changes in relative abundance in Puget Sound from 2003-2005 are reported here. At the Seattle Aquarium study site, 45 sixgills were tagged with modified Floy visual marker tags, along with an estimated 197 observations of untagged sharks plus 31 returning tagged sharks, for a total of 273 sixgill observations recorded. A mark-resight statistical model based on analysis of underwater video estimated a range of abundance from a high of 98 sharks seen in July of 2004 to a low of 32 sharks seen in March of 2004. Both analyses found sixgills significantly more abundant in the summer months at the Seattle Aquarium's research station.

Observations on Abundance of Bluntnose Sixgill Sharks, Hexanchus griseus, in an Urban Waterway in Puget Sound, 2003-2005

PubMed Central

Griffing, Denise; Larson, Shawn; Hollander, Joel; Carpenter, Tim; Christiansen, Jeff; Doss, Charles

2014-01-01

The bluntnose sixgill shark, Hexanchus griseus, is a widely distributed but poorly understood large, apex predator. Anecdotal reports of diver-shark encounters in the late 1990’s and early 2000’s in the Pacific Northwest stimulated interest in the normally deep-dwelling shark and its presence in the shallow waters of Puget Sound. Analysis of underwater video documenting sharks at the Seattle Aquarium’s sixgill research site in Elliott Bay and mark-resight techniques were used to answer research questions about abundance and seasonality. Seasonal changes in relative abundance in Puget Sound from 2003–2005 are reported here. At the Seattle Aquarium study site, 45 sixgills were tagged with modified Floy visual marker tags, along with an estimated 197 observations of untagged sharks plus 31 returning tagged sharks, for a total of 273 sixgill observations recorded. A mark-resight statistical model based on analysis of underwater video estimated a range of abundance from a high of 98 sharks seen in July of 2004 to a low of 32 sharks seen in March of 2004. Both analyses found sixgills significantly more abundant in the summer months at the Seattle Aquarium’s research station. PMID:24475229

Thin Fresnel zone plate lenses for focusing underwater sound

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calvo, David C., E-mail: david.calvo@nrl.navy.mil; Thangawng, Abel L.; Nicholas, Michael

A Fresnel zone plate (FZP) lens of the Soret type creates a focus by constructive interference of waves diffracted through open annular zones in an opaque screen. For underwater sound below MHz frequencies, a large FZP that blocks sound using high-impedance, dense materials would have practical disadvantages. We experimentally and numerically investigate an alternative approach of creating a FZP with thin (0.4λ) acoustically opaque zones made of soft silicone rubber foam attached to a thin (0.1λ) transparent rubber substrate. An ultra-thin (0.0068λ) FZP that achieves higher gain is also proposed and simulated which uses low-volume fraction, bubble-like resonant air ringmore » cavities to construct opaque zones. Laboratory measurements at 200 kHz indicate that the rubber foam can be accurately modeled as a lossy fluid with an acoustic impedance approximately 1/10 that of water. Measured focal gains up to 20 dB agree with theoretical predictions for normal and oblique incidence. The measured focal radius of 0.68λ (peak-to-null) agrees with the Rayleigh diffraction limit prediction of 0.61 λ/NA (NA = 0.88) for a low-aberration lens.« less

Attenuation of standing waves in a large water tank using arrays of large tethered encapsulated bubbles.

PubMed

Lee, Kevin M; Wilson, Preston S; Wochner, Mark S

2014-04-01

The use of bubble resonance effects to attenuate low-frequency underwater sound was investigated experimentally in a large water tank. A compact electromechanical sound source was used to excite standing wave fields at frequencies ranging between 50 and 200 Hz in the tank. The source was then surrounded by a stationary array of tethered encapsulated air bubbles, and reduction in standing wave amplitude by as much as 26 dB was observed. The bubbles consisted of either thin-shelled latex balloons with approximately 5 cm radii or thicker-shelled vinyl boat fenders with 6.9 cm radii. The effects of changing the material and thickness of the bubble shells were found to be in qualitative agreement with predictions from Church's model for sound propagation in a liquid containing encapsulated bubbles [J. Acoust. Soc. Am. 97, 1510-1521 (1995)]. Although demonstrated here for low frequency noise abatement within a tank, which is useful for quieting acoustic test facilities and large tanks used for marine life husbandry, the eventual aim of this work is to use stationary arrays of large tethered encapsulated bubbles to abate low frequency underwater noise from anthropogenic sources in the marine environment.

Experimental investigation of sound absorption properties of perforated date palm fibers panel

NASA Astrophysics Data System (ADS)

Elwaleed, A. K.; Nikabdullah, N.; Nor, M. J. M.; Tahir, M. F. M.; Zulkifli, R.

2013-06-01

This paper presents the sound absorption properties of a natural waste of date palm fiber perforated panel. A single layer of the date palm fibers was tested in this study for its sound absorption properties. The experimental measurements were carried out using impedance tube at the acoustic lab, Faculty of Engineering, Universiti Kebangsaan Malaysia. The experiment was conducted for the panel without air gap, with air gap and with perforated plate facing. Three air gap thicknesses of 10 mm, 20 mm and 30 mm were used between the date palm fiber sample and the rigid backing of the impedance tube. The results showed that when facing the palm date fiber sample with perforated plate the sound absorption coefficient improved at the higher and lower frequency ranges. This increase in sound absorption coincided with reduction in medium frequency absorption. However, this could be improved by using different densities or perforated plate with the date palm fiber panel.

Bottom-up approach for microstructure optimization of sound absorbing materials.

PubMed

Perrot, Camille; Chevillotte, Fabien; Panneton, Raymond

2008-08-01

Results from a numerical study examining micro-/macrorelations linking local geometry parameters to sound absorption properties are presented. For a hexagonal structure of solid fibers, the porosity phi, the thermal characteristic length Lambda('), the static viscous permeability k(0), the tortuosity alpha(infinity), the viscous characteristic length Lambda, and the sound absorption coefficient are computed. Numerical solutions of the steady Stokes and electrical equations are employed to provide k(0), alpha(infinity), and Lambda. Hybrid estimates based on direct numerical evaluation of phi, Lambda('), k(0), alpha(infinity), Lambda, and the analytical model derived by Johnson, Allard, and Champoux are used to relate varying (i) throat size, (ii) pore size, and (iii) fibers' cross-section shapes to the sound absorption spectrum. The result of this paper tends to demonstrate the important effect of throat size in the sound absorption level, cell size in the sound absorption frequency selectivity, and fibers' cross-section shape in the porous material weight reduction. In a hexagonal porous structure with solid fibers, the sound absorption level will tend to be maximized with a 48+/-10 microm throat size corresponding to an intermediate resistivity, a 13+/-8 microm fiber radius associated with relatively small interfiber distances, and convex triangular cross-section shape fibers allowing weight reduction.

Prediction of sound absorption in rigid porous media with the lattice Boltzmann method

NASA Astrophysics Data System (ADS)

da Silva, Andrey Ricardo; Mareze, Paulo; Brandão, Eric

2016-02-01

In this work, sound absorption phenomena associated with the viscous shear stress within rigid porous media is investigated with a simple isothermal lattice Boltzmann BGK model. Simulations are conducted for different macroscopic material properties such as sample thickness and porosity and the results are compared with the exact analytical solution for materials with slit-like structure in terms of acoustic impedance and sound absorption coefficient. The numerical results agree very well with the exact solution, particularly for the sound absorption coefficient. The small deviations found in the low frequency limit for the real part of the acoustic impedance are attributed to the ratio between the thicknesses of the slit and the viscous boundary layer. The results suggest that the lattice Boltzmann method can be a very compelling numerical tool for simulating viscous sound absorption phenomena in the time domain, particularly due to its computational simplicity when compared to traditional continuum based techniques.

Analysis of High Spatial, Temporal, and Directional Resolution Recordings of Biological Sounds in the Southern California Bight

DTIC Science & Technology

2013-09-30

transiting whales in the Southern California Bight, b) the use of passive underwater acoustic techniques for improved habitat assessment in biologically...sensitive areas and improved ecosystem modeling, and c) the application of the physics of excitable media to numerical modeling of biological choruses...was on the potential impact of man-made sounds on the calling behavior of transiting humpback whales in the Southern California Bight. The main

Nonlinear Effects in Long Range Underwater Acoustic Propagation

DTIC Science & Technology

1985-11-01

Introduction to the Theory of Sound ransmission with Application to the Ocean (McGraw-Hill Book Co., Inc., New York). Oppenheim, Alan V., and Ronald W. Schafer...34Propagation of Finite-Amplitude Sound Waves in an Inhomogeneous Medium with Caustics," Sov. Phys.-Acoust. 22, 516-520. Panton, Ronald L. (1984...21 W. A. Kuperman 22 B. E. McDonald Naval Ocean Research and Development Activity NSTL Station, MS 39529 23 Attn: R. A. Wagstaff New London Laboratory

Analysis of High Spatial, Temporal, and Directional Resolution Recordings of Biological Sounds in the Southern California Bight

DTIC Science & Technology

2012-09-30

tested in this research is that the evolution of unit structure and song characteristics in the population of transiting humpback whales in the Southern...behavior of transiting humpback whales in the Southern California Bight, b) the use of passive underwater acoustic techniques for improved habitat...man-made sounds on the calling behavior of transiting humpback whales in the Southern California Bight”. The main scientific hypothesis to be

Equivalent modulus method for finite element simulation of the sound absorption of anechoic coating backed with orthogonally rib-stiffened plate

NASA Astrophysics Data System (ADS)

Jin, Zhongkun; Yin, Yao; Liu, Bilong

2016-03-01

The finite element method is often used to investigate the sound absorption of anechoic coating backed with orthogonally rib-stiffened plate. Since the anechoic coating contains cavities, the number of grid nodes of a periodic unit cell is usually large. An equivalent modulus method is proposed to reduce the large amount of nodes by calculating an equivalent homogeneous layer. Applications of this method in several models show that the method can well predict the sound absorption coefficient of such structure in a wide frequency range. Based on the simulation results, the sound absorption performance of such structure and the influences of different backings on the first absorption peak are also discussed.

Measurements of optical underwater turbulence under controlled conditions

NASA Astrophysics Data System (ADS)

Kanaev, A. V.; Gladysz, S.; Almeida de Sá Barros, R.; Matt, S.; Nootz, G. A.; Josset, D. B.; Hou, W.

2016-05-01

Laser beam propagation underwater is becoming an important research topic because of high demand for its potential applications. Namely, ability to image underwater at long distances is highly desired for scientific and military purposes, including submarine awareness, diver visibility, and mine detection. Optical communication in the ocean can provide covert data transmission with much higher rates than that available with acoustic techniques, and it is now desired for certain military and scientific applications that involve sending large quantities of data. Unfortunately underwater environment presents serious challenges for propagation of laser beams. Even in clean ocean water, the extinction due to absorption and scattering theoretically limit the useful range to few attenuation lengths. However, extending the laser light propagation range to the theoretical limit leads to significant beam distortions due to optical underwater turbulence. Experiments show that the magnitude of the distortions that are caused by water temperature and salinity fluctuations can significantly exceed the magnitude of the beam distortions due to atmospheric turbulence even for relatively short propagation distances. We are presenting direct measurements of optical underwater turbulence in controlled conditions of laboratory water tank using two separate techniques involving wavefront sensor and LED array. These independent approaches will enable development of underwater turbulence power spectrum model based directly on the spatial domain measurements and will lead to accurate predictions of underwater beam propagation.

Absorption of sound by tree bark

Treesearch

G. Reethof; L. D. Frank; O. H. McDaniel

1976-01-01

Laboratory tests were conducted with a standing wave tube to measure the acoustic absorption of normally incident sound by the bark of six species of trees. Twelve bark samples, 10 cm in diameter, were tested. Sound of seven frequencies between 400 and 1600 Hz was used in the measurements. Absorption was generally about 5 percent; it exceeded 10 percent for only three...

Characterization of Sheep Wool as a Sustainable Material for Acoustic Applications

PubMed Central

Uris, Antonio; Candelas, Pilar

2017-01-01

In recent years, natural materials are becoming a valid alternative to traditional sound absorbers due to reduced production costs and environmental protection. This paper reports the acoustical characterization of sheep wool. Measurements on normal incidence and diffuse-incidence sound absorption coefficients of different samples are reported. The airflow resistance has also been measured. The results prove that sheep wool has a comparable sound absorption performance to that of mineral wool or recycled polyurethane foam. An empirical model is used to calculate the sound absorption of sheep wool samples. A reasonable agreement on the acoustic absorption of all sheep wool samples is obtained. PMID:29112133

Characterization of Sheep Wool as a Sustainable Material for Acoustic Applications.

PubMed

Del Rey, Romina; Uris, Antonio; Alba, Jesús; Candelas, Pilar

2017-11-07

In recent years, natural materials are becoming a valid alternative to traditional sound absorbers due to reduced production costs and environmental protection. This paper reports the acoustical characterization of sheep wool. Measurements on normal incidence and diffuse-incidence sound absorption coefficients of different samples are reported. The airflow resistance has also been measured. The results prove that sheep wool has a comparable sound absorption performance to that of mineral wool or recycled polyurethane foam. An empirical model is used to calculate the sound absorption of sheep wool samples. A reasonable agreement on the acoustic absorption of all sheep wool samples is obtained.

Study on Prediction of Underwater Radiated Noise from Propeller Tip Vortex Cavitation

NASA Astrophysics Data System (ADS)

Yamada, Takuyoshi; Sato, Kei; Kawakita, Chiharu; Oshima, Akira

2015-12-01

The method to predict underwater radiated noise from tip vortex cavitation was studied. The growth of a single cavitation bubble in tip vortex was estimated by substituting the tip vortex to Rankine combined vortex. The ideal spectrum function for the sound pressure generated by a single cavitation bubble was used, also the empirical factor for the number of collapsed bubbles per unit time was introduced. The estimated noise data were compared with measured ship's ones and it was found out that this method can estimate noise data within 3dB difference.

Noise abatement in a pine plantation

Treesearch

R. E. Leonard; L. P. Herrington

1971-01-01

Observations on sound propagation were made in two red pine plantations. Measurements were taken of attenuation of prerecorded frequencies at various distances from the sound source. Sound absorption was strongly dependent on frequencies. Peak absorption was at 500 Hz.

Novel underwater soundscape: acoustic repertoire of plainfin midshipman fish.

PubMed

McIver, Eileen L; Marchaterre, Margaret A; Rice, Aaron N; Bass, Andrew H

2014-07-01

Toadfishes are among the best-known groups of sound-producing (vocal) fishes and include species commonly known as toadfish and midshipman. Although midshipman have been the subject of extensive investigation of the neural mechanisms of vocalization, this is the first comprehensive, quantitative analysis of the spectro-temporal characters of their acoustic signals and one of the few for fishes in general. Field recordings of territorial, nest-guarding male midshipman during the breeding season identified a diverse vocal repertoire composed of three basic sound types that varied widely in duration, harmonic structure and degree of amplitude modulation (AM): 'hum', 'grunt' and 'growl'. Hum duration varied nearly 1000-fold, lasting for minutes at a time, with stable harmonic stacks and little envelope modulation throughout the sound. By contrast, grunts were brief, ~30-140 ms, broadband signals produced both in isolation and repetitively as a train of up to 200 at intervals of ~0.5-1.0 s. Growls were also produced alone or repetitively, but at variable intervals of the order of seconds with durations between those of grunts and hums, ranging 60-fold from ~200 ms to 12 s. Growls exhibited prominent harmonics with sudden shifts in pulse repetition rate and highly variable AM patterns, unlike the nearly constant AM of grunt trains and flat envelope of hums. Behavioral and neurophysiological studies support the hypothesis that each sound type's unique acoustic signature contributes to signal recognition mechanisms. Nocturnal production of these sounds against a background chorus dominated constantly for hours by a single sound type, the multi-harmonic hum, reveals a novel underwater soundscape for fish. © 2014. Published by The Company of Biologists Ltd.

Sound and human impacts on beluga whales in Cook Inlet, Alaska

NASA Astrophysics Data System (ADS)

Blevins, Rachael E.

Cook Inlet beluga whales (CIBs) are a geographically and genetically isolated population residing in Cook Inlet, Alaska year round. The population declined by approximately 50% between 1994 and 1998 and was listed as endangered under the Endangered Species Act in 2008. The original decline was attributed to overharvest; however, the population has failed to rebound despite the virtual absence of harvest since 1998. This suggests that other factors, such as declining prey availability, increased predation, contaminants, disease, climate change, catastrophic events, habitat loss, unauthorized take, and underwater noise pollution, may be limiting the population's recovery. The goal of this dissertation research was to study the potential impacts of underwater noise on the CIB population. The objective of Chapter 1 was to study CIB acoustic behavior to gain a greater understanding of how CIBs utilize sound. The objective of Chapter 2 was to measure underwater sound levels in Cook Inlet to understand the background noise levels with which CIBs must cope. The objective of Chapter 3 was to document reactions of CIBs to noise disturbance utilizing local ecological knowledge to allow insight into the potential impacts of noise on beluga behavior. The results of Chapter 1 showed that belugas exhibit significant seasonal and spatial variation in calling behavior which suggested differences in habitat usage or differences in the surrounding environment, including background noise levels. The results of Chapter 2 showed that root mean square sound pressure levels exhibited high variation with the highest levels recorded in the 100 Hz frequency band. The seasonal differences in sound levels observed in this study were likely due to greater small vessel traffic and oil and gas development activities in the summer than the winter. In Chapter 3, participants reported observations of CIBs exhibiting avoidance reactions to noise sources including boats, planes, explosions, pile driving, construction, and cars. The results of this chapter showed that noise is perceived to alter beluga behavior and possibly beluga distribution in Cook Inlet. This dissertation research showed that underwater noise has the potential to affect CIBs, however the cost of this impact remains unclear and warrants further study. In light of the lack of support for many of the proposed factors limiting the population and the need for further research for many of these factors, it would be valuable to consider the cumulative effects of these multiple stressors. While their potential impact may be small individually, when combined, these factors may have a synergistic and significant impact on individual whales and, in turn, on the CIB population. Management of cumulative effects may be necessary to ensure the recovery of this endangered population.

Warfare Ecology on an Underwater Demolition Range: Acoustic Observations of Marine Life and Shallow Water Detonations in Hawai`i

NASA Astrophysics Data System (ADS)

Shannon, Lee H.

Most studies investigating the effects of military-associated anthropogenic noise concentrate on deep sea or open ocean propagation of sonar and its effect on marine mammals. In littoral waters, U.S. military special operations units regularly conduct shallow water explosives training, yet relatively little attention has been given to the potential impact on nearshore marine ecosystems from these underwater detonations. This dissertation research focused on the Pu'uloa Underwater Detonation Range off the coast of O`ahu, and examined multiple aspects of the surrounding marine ecosystem and the effects of detonations using acoustic monitoring techniques. The soundscape of a nearshore reef ecosystem adjacent to the UNDET range was characterized through analysis of passive acoustic recordings collected over the span of 6 years. Snapping shrimp were the predominant source of noise, and a diel pattern was present, with increased sound energy during the night hours. Results revealed a difference of up to 7dB between two Ecological Acoustic Recorder locations 2.5km apart along the 60ft isobath. Passive acoustic recording files were searched visually and aurally for odontocete whistles. Whistles were detected in only 0.6% of files analyzed, indicating this area is not frequently transited by coastal odontocete emitting social sounds. The study also opportunistically captured a humpback whale singing during a detonation event, during which the animal showed no obvious alteration of its singing behavior. Four separate underwater detonation events were recorded using a surface deployed F-42C transducer, and the resulting analysis showed no measurable drop in the biologically produced acoustic energy in reaction to the explosive events. Coral reef fishes were recorded visually and acoustically during detonation events at a known distance and bearing from a known explosive sound source. Individual fish behavioral responses to the explosion varied, and a sharp uptick in fish vocalizations was recorded immediately following the blast, with rapid (within 30s) return to baseline visual and acoustic behavior. The results and conclusions of these studies are placed within the broader context of warfare ecology as an emerging scientific discipline.

Measurements of pile driving noise from control piles and noise-reduced piles at the Vashon Island ferry dock.

DOT National Transportation Integrated Search

2017-04-01

As part of the Washington State Department of Transportation (WSDOT) pile attenuation test program, : researchers from the University of Washington Applied Physics Laboratory (APL-UW) conducted underwater sound : measurements on 7 and 8 December 2015...

A Volunteer Computing Project for Solving Geoacoustic Inversion Problems

NASA Astrophysics Data System (ADS)

Zaikin, Oleg; Petrov, Pavel; Posypkin, Mikhail; Bulavintsev, Vadim; Kurochkin, Ilya

2017-12-01

A volunteer computing project aimed at solving computationally hard inverse problems in underwater acoustics is described. This project was used to study the possibilities of the sound speed profile reconstruction in a shallow-water waveguide using a dispersion-based geoacoustic inversion scheme. The computational capabilities provided by the project allowed us to investigate the accuracy of the inversion for different mesh sizes of the sound speed profile discretization grid. This problem suits well for volunteer computing because it can be easily decomposed into independent simpler subproblems.

Measurement of Transmission Loss Using an Inexpensive Mobile Source on the Upper Slope of the South China Sea

DTIC Science & Technology

2015-09-01

reduction of SPL in dB as sound travels from a source to a receiver ( Urick 1983). The basic equation to obtain TL from measurements in a tonal transmission...attributed to the sum of losses due to spreading, multipath effects, scattering, and attenuation ( Urick 1983). Typical values for TL in different areas...executive.com/article/us-toughens- south-china-sea-stance.] Urick , R. J., 1983: Principles of Underwater Sound. 3rd ed. Peninsula Publishing, 423 pp. 32

Elastic parabolic equation and normal mode solutions for seismo-acoustic propagation in underwater environments with ice covers.

PubMed

Collis, Jon M; Frank, Scott D; Metzler, Adam M; Preston, Kimberly S

2016-05-01

Sound propagation predictions for ice-covered ocean acoustic environments do not match observational data: received levels in nature are less than expected, suggesting that the effects of the ice are substantial. Effects due to elasticity in overlying ice can be significant enough that low-shear approximations, such as effective complex density treatments, may not be appropriate. Building on recent elastic seafloor modeling developments, a range-dependent parabolic equation solution that treats the ice as an elastic medium is presented. The solution is benchmarked against a derived elastic normal mode solution for range-independent underwater acoustic propagation. Results from both solutions accurately predict plate flexural modes that propagate in the ice layer, as well as Scholte interface waves that propagate at the boundary between the water and the seafloor. The parabolic equation solution is used to model a scenario with range-dependent ice thickness and a water sound speed profile similar to those observed during the 2009 Ice Exercise (ICEX) in the Beaufort Sea.

Sound Pressure Level Gain in an Acoustic Metamaterial Cavity

PubMed Central

Song, Kyungjun; Kim, Kiwon; Hur, Shin; Kwak, Jun-Hyuk; Park, Jihyun; Yoon, Jong Rak; Kim, Jedo

2014-01-01

The inherent attenuation of a homogeneous viscous medium limits radiation propagation, thereby restricting the use of many high-frequency acoustic devices to only short-range applications. Here, we design and experimentally demonstrate an acoustic metamaterial localization cavity which is used for sound pressure level (SPL) gain using double coiled up space like structures thereby increasing the range of detection. This unique behavior occurs within a subwavelength cavity that is 1/10th of the wavelength of the incident acoustic wave, which provides up to a 13 dB SPL gain. We show that the amplification results from the Fabry-Perot resonance of the cavity, which has a simultaneously high effective refractive index and effective impedance. We also experimentally verify the SPL amplification in an underwater environment at higher frequencies using a sample with an identical unit cell size. The versatile scalability of the design shows promising applications in many areas, especially in acoustic imaging and underwater communication. PMID:25502279

Improving sound absorption property of polyurethane foams doped with natural fiber

NASA Astrophysics Data System (ADS)

Azahari, M. Shafiq M.; Rus, Anika Zafiah M.; Taufiq Zaliran, M.; Kormin, Shaharuddin

2017-08-01

This study investigates the acoustics behavior of wood fibre filler of Red Meranti - filled polyurethane foam as a sound absorbing material. Three different thicknesses have been selected which is 10 mm, 20 mm and 30 mm. By choosing percentage loading of Red Meranti (RM) wood fibre of 5%, 10%, 15% and 20% added with polymer foam is namely as polymer foam (PF) composites of PF5%, PF10%, PF15% and PF20%. The sound absorption coefficient (α) and pore structure of the foam samples have been examined by using Impedance Tube test and Scanning Electron Microscopy (SEM). The results revealed that the highest thickness of highest filler loading (PF20%) gives higher sound absorption coefficient (α). The absorption frequency level is observed at 0.9922 and 0.99889 which contributed from low and high frequency absorption level respectively. The smallest pores size structure was observed with highest filler loading of PF. The higher the thickness and the higher the percentage loading of wood filler gives smaller pore structure, consequently, increased the sound absorption coefficient level.

Problems in nonlinear acoustics: Pulsed finite amplitude sound beams, nonlinear acoustic wave propagation in a liquid layer, nonlinear effects in asymmetric cylindrical sound beams, effects of absorption on the interaction of sound beams, and parametric receiving arrays

NASA Astrophysics Data System (ADS)

Hamilton, Mark F.

1990-12-01

This report discusses five projects all of which involve basic theoretical research in nonlinear acoustics: (1) pulsed finite amplitude sound beams are studied with a recently developed time domain computer algorithm that solves the KZK nonlinear parabolic wave equation; (2) nonlinear acoustic wave propagation in a liquid layer is a study of harmonic generation and acoustic soliton information in a liquid between a rigid and a free surface; (3) nonlinear effects in asymmetric cylindrical sound beams is a study of source asymmetries and scattering of sound by sound at high intensity; (4) effects of absorption on the interaction of sound beams is a completed study of the role of absorption in second harmonic generation and scattering of sound by sound; and (5) parametric receiving arrays is a completed study of parametric reception in a reverberant environment.

Ontogenetic investigation of underwater hearing capabilities in loggerhead sea turtles (Caretta caretta) using a dual testing approach.

PubMed

Lavender, Ashley L; Bartol, Soraya M; Bartol, Ian K

2014-07-15

Sea turtles reside in different acoustic environments with each life history stage and may have different hearing capacity throughout ontogeny. For this study, two independent yet complementary techniques for hearing assessment, i.e. behavioral and electrophysiological audiometry, were employed to (1) measure hearing in post-hatchling and juvenile loggerhead sea turtles Caretta caretta (19-62 cm straight carapace length) to determine whether these migratory turtles exhibit an ontogenetic shift in underwater auditory detection and (2) evaluate whether hearing frequency range and threshold sensitivity are consistent in behavioral and electrophysiological tests. Behavioral trials first required training turtles to respond to known frequencies, a multi-stage, time-intensive process, and then recording their behavior when they were presented with sound stimuli from an underwater speaker using a two-response forced-choice paradigm. Electrophysiological experiments involved submerging restrained, fully conscious turtles just below the air-water interface and recording auditory evoked potentials (AEPs) when sound stimuli were presented using an underwater speaker. No significant differences in behavior-derived auditory thresholds or AEP-derived auditory thresholds were detected between post-hatchling and juvenile sea turtles. While hearing frequency range (50-1000/1100 Hz) and highest sensitivity (100-400 Hz) were consistent in audiograms pooled by size class for both behavior and AEP experiments, both post-hatchlings and juveniles had significantly higher AEP-derived than behavior-derived auditory thresholds, indicating that behavioral assessment is a more sensitive testing approach. The results from this study suggest that post-hatchling and juvenile loggerhead sea turtles are low-frequency specialists, exhibiting little differences in threshold sensitivity and frequency bandwidth despite residence in acoustically distinct environments throughout ontogeny. © 2014. Published by The Company of Biologists Ltd.

National Oceanic and Atmospheric Administration's Cetacean and Sound Mapping Effort: Continuing Forward with an Integrated Ocean Noise Strategy.

PubMed

Harrison, Jolie; Ferguson, Megan; Gedamke, Jason; Hatch, Leila; Southall, Brandon; Van Parijs, Sofie

2016-01-01

To help manage chronic and cumulative impacts of human activities on marine mammals, the National Oceanic and Atmospheric Administration (NOAA) convened two working groups, the Underwater Sound Field Mapping Working Group (SoundMap) and the Cetacean Density and Distribution Mapping Working Group (CetMap), with overarching effort of both groups referred to as CetSound, which (1) mapped the predicted contribution of human sound sources to ocean noise and (2) provided region/time/species-specific cetacean density and distribution maps. Mapping products were presented at a symposium where future priorities were identified, including institutionalization/integration of the CetSound effort within NOAA-wide goals and programs, creation of forums and mechanisms for external input and funding, and expanded outreach/education. NOAA is subsequently developing an ocean noise strategy to articulate noise conservation goals and further identify science and management actions needed to support them.

Nanocellulose based polymer composite for acoustical materials

NASA Astrophysics Data System (ADS)

Farid, Mohammad; Purniawan, Agung; Susanti, Diah; Priyono, Slamet; Ardhyananta, Hosta; Rahmasita, Mutia E.

2018-04-01

Natural fibers are biodegradable materials that are innovatively and widely used for composite reinforcement in automotive components. Nanocellulose derived from natural fibers oil palm empty bunches have properties that are remarkable for use as a composite reinforcement. However, there have not been many investigations related to the use of nanocellulose-based composites for wideband sound absorption materials. The specimens of nanocellulose-based polyester composite were prepared using a spray method. An impedance tube method was used to measure the sound absorption coefficient of this composite material. To reveal the characteristics of the nanocellulose-based polyester composite material, SEM (scanning electron microscope), TEM (Transmission Electron Microscope), FTIR (Fourier Transform Infra Red), TGA (Thermogravimetric Analysis), and density tests were performed. Sound absorption test results showed the average value of sound absorption coefficient of 0.36 to 0,46 for frequency between 500 and 4000 Hz indicating that this nanocellulose-based polyester composite materials had a tendency to wideband sound absorption materials and potentially used as automotive interior materials.

Acoustic radiation force on a multilayered sphere in a Gaussian standing field

NASA Astrophysics Data System (ADS)

Wang, Haibin; Liu, Xiaozhou; Gao, Sha; Cui, Jun; Liu, Jiehui; He, Aijun; Zhang, Gutian

2018-03-01

We develop a model for calculating the radiation force on spherically symmetric multilayered particles based on the acoustic scattering approach. An expression is derived for the radiation force on a multilayered sphere centered on the axis of a Gaussian standing wave propagating in an ideal fluid. The effects of the sound absorption of the materials and sound wave on acoustic radiation force of a multilayered sphere immersed in water are analyzed, with particular emphasis on the shell thickness of every layer, and the width of the Gaussian beam. The results reveal that the existence of particle trapping behavior depends on the choice of the non-dimensional frequency ka, as well as the shell thickness of each layer. This study provides a theoretical basis for the development of acoustical tweezers in a Gaussian standing wave, which may benefit the improvement and development of acoustic control technology, such as trapping, sorting, and assembling a cell, and drug delivery applications. Project supported by National Key R&D Program (Grant No. 2016YFF0203000), the National Natural Science Foundation of China (Grant Nos. 11774167 and 61571222), the Fundamental Research Funds for the Central Universities of China (Grant No. 020414380001), the Key Laboratory of Underwater Acoustic Environment, Institute of Acoustics, Chinese Academy of Sciences (Grant No. SSHJ-KFKT-1701), and the AQSIQ Technology R&D Program of China (Grant No. 2017QK125).

Underwater detection by using ultrasonic sensor

NASA Astrophysics Data System (ADS)

Bakar, S. A. A.; Ong, N. R.; Aziz, M. H. A.; Alcain, J. B.; Haimi, W. M. W. N.; Sauli, Z.

2017-09-01

This paper described the low cost implementation of hardware and software in developing the system of ultrasonic which can visualize the feedback of sound in the form of measured distance through mobile phone and monitoring the frequency of detection by using real time graph of Java application. A single waterproof transducer of JSN-SR04T had been used to determine the distance of an object based on operation of the classic pulse echo detection method underwater. In this experiment, the system was tested by placing the housing which consisted of Arduino UNO, Bluetooth module of HC-06, ultrasonic sensor and LEDs at the top of the box and the transducer was immersed in the water. The system which had been tested for detection in vertical form was found to be capable of reporting through the use of colored LEDs as indicator to the relative proximity of object distance underwater form the sensor. As a conclusion, the system can detect the presence of an object underwater within the range of ultrasonic sensor and display the measured distance onto the mobile phone and the real time graph had been successfully generated.

Metaporous layer to overcome the thickness constraint for broadband sound absorption

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Jieun; Lee, Joong Seok; Kim, Yoon Young, E-mail: yykim@snu.ac.kr

The sound absorption of a porous layer is affected by its thickness, especially in a low-frequency range. If a hard-backed porous layer contains periodical arrangements of rigid partitions that are coordinated parallel and perpendicular to the direction of incoming sound waves, the lower bound of the effective sound absorption can be lowered much more and the overall absorption performance enhanced. The consequence of rigid partitioning in a porous layer is to make the first thickness resonance mode in the layer appear at much lower frequencies compared to that in the original homogeneous porous layer with the same thickness. Moreover, appropriatemore » partitioning yields multiple thickness resonances with higher absorption peaks through impedance matching. The physics of the partitioned porous layer, or the metaporous layer, is theoretically investigated in this study.« less

Fusion and Gaussian mixture based classifiers for SONAR data

NASA Astrophysics Data System (ADS)

Kotari, Vikas; Chang, KC

2011-06-01

Underwater mines are inexpensive and highly effective weapons. They are difficult to detect and classify. Hence detection and classification of underwater mines is essential for the safety of naval vessels. This necessitates a formulation of highly efficient classifiers and detection techniques. Current techniques primarily focus on signals from one source. Data fusion is known to increase the accuracy of detection and classification. In this paper, we formulated a fusion-based classifier and a Gaussian mixture model (GMM) based classifier for classification of underwater mines. The emphasis has been on sound navigation and ranging (SONAR) signals due to their extensive use in current naval operations. The classifiers have been tested on real SONAR data obtained from University of California Irvine (UCI) repository. The performance of both GMM based classifier and fusion based classifier clearly demonstrate their superior classification accuracy over conventional single source cases and validate our approach.

Sounds produced by individual white whales, Delphinapterus leucas, from Svalbard during capture (L)

NASA Astrophysics Data System (ADS)

van Parijs, Sofie M.; Lydersen, Christian; Kovacs, Kit M.

2003-01-01

Recordings were made of the sounds produced by white whales during capture events in Storfjorden, Svalbard, in the late autumn. Only four of eight captured individuals produced sounds. Four subadults, one female and three males, between 330 and 375 cm long, did not produce sounds during handling. The four animals that produced sounds were as follows: a female subadult of 280 cm produced repetitive broadband clicks; a solitary calf produced harmonic sounds, which we suggest may serve as mother-calf ``contact calls,'' and a mother-calf pair were the two animals that produced the most sounds in the study. The mother produced ``crooning'' broadband clicks and frequently moved her head toward her calf while producing underwater sounds. The calf produced three types of frequency-modulated sounds interspersed within broadband click trains. No sounds were heard from any of the animals once they were free-swimming, or during ad lib recording sessions in the study area, even though groups of white whales were sighted on several occasions away from the capture net.

A comparison of underwater hearing sensitivity in bottlenose dolphins (Tursiops truncatus) determined by electrophysiological and behavioral methods.

PubMed

Houser, Dorian S; Finneran, James J

2006-09-01

Variable stimulus presentation methods are used in auditory evoked potential (AEP) estimates of cetacean hearing sensitivity, each of which might affect stimulus reception and hearing threshold estimates. This study quantifies differences in underwater hearing thresholds obtained by AEP and behavioral means. For AEP estimates, a transducer embedded in a suction cup (jawphone) was coupled to the dolphin's lower jaw for stimulus presentation. Underwater AEP thresholds were obtained for three dolphins in San Diego Bay and for one dolphin in a quiet pool. Thresholds were estimated from the envelope following response at carrier frequencies ranging from 10 to 150 kHz. One animal, with an atypical audiogram, demonstrated significantly greater hearing loss in the right ear than in the left. Across test conditions, the range and average difference between AEP and behavioral threshold estimates were consistent with published comparisons between underwater behavioral and in-air AEP thresholds. AEP thresholds for one animal obtained in-air and in a quiet pool demonstrated a range of differences of -10 to 9 dB (mean = 3 dB). Results suggest that for the frequencies tested, the presentation of sound stimuli through a jawphone, underwater and in-air, results in acceptable differences to AEP threshold estimates.

Sound decay in a rectangular room with impedance walls

NASA Astrophysics Data System (ADS)

Kanev, N. G.

2012-09-01

The problem of sound decay in a rectangular room is considered for the case of a room with walls the acoustic properties of which are described by the impedance, which implies a dependence of the absorption coefficient on the angle of incidence of sound waves. The ray approximation is used to determine the sound decay laws for different distributions of wall absorption. It is shown that, in a room with impedance walls, the sound decay is slower than in the conventional reverberation model, in which the wall absorption coefficient is independent of the angle of incidence. The problem is also solved in the wave approximation to determine the decay law for a preset frequency band.

Sound absorption of low-temperature reusable surface insulation candidate materials

NASA Technical Reports Server (NTRS)

Johnston, J. D.

1974-01-01

Sound absorption data from tests of four candidate low-temperature reusable surface insulation materials are presented. Limitations on the use of the data are discussed, conclusions concerning the effective absorption of the materials are drawn, and the relative significance to Vibration and Acoustic Test Facility test planning of the absorption of each material is assessed.

The application of standard definitions of sound to the fields of underwater acoustics and acoustical oceanography

NASA Astrophysics Data System (ADS)

Carey, William M.

2004-05-01

Recent societal concerns have focused attention on the use of sound as a probe to investigate the oceans and its use in naval sonar applications. The concern is the impact the use of sound may have on marine mammals and fishes. The focus has changed the fields of acoustical oceanography (AO) and underwater acoustics (UW) because of the requirement to communicate between disciplines. Multiple National Research Council publications, Dept. of Navy reports, and several monographs have been written on this subject, and each reveals the importance as well as the misapplication of ASA standards. The ANSI-ASA standards are comprehensive, however not widely applied. The clear definition of standards and recommendations of their use is needed for both scientists and government agencies. Traditionally the U.S. Navy has been responsible for UW standards and calibration; the ANSI-ASA standards have been essential. However, recent changes in the Navy and its laboratory structure may necessitate a more formal recognition of ANSI-ASA standards and perhaps incorporation of UW-AO in the Bureau of Standards. A separate standard for acoustical terminology, reference levels, and notation used in the UW-AO is required. Since the problem is global, a standard should be compatible and cross referenced with the International Standard (CEI/IEC 27-3).

Short- and long-term monitoring of underwater sound levels in the Hudson River (New York, USA).

PubMed

Martin, S Bruce; Popper, Arthur N

2016-04-01

There is a growing body of research on natural and man-made sounds that create aquatic soundscapes. Less is known about the soundscapes of shallow waters, such as in harbors, rivers, and lakes. Knowledge of soundscapes is needed as a baseline against which to determine the changes in noise levels resulting from human activities. To provide baseline data for the Hudson River at the site of the Tappan Zee Bridge, 12 acoustic data loggers were deployed for a 24-h period at ranges of 0-3000 m from the bridge, and four of the data loggers were re-deployed for three months of continuous recording. Results demonstrate that this region of the river is relatively quiet compared to open ocean conditions and other large river systems. Moreover, the soundscape had temporal and spatial diversity. The temporal patterns of underwater noise from the bridge change with the cadence of human activity. Bridge noise (e.g., road traffic) was only detected within 300 m; farther from the bridge, boating activity increased sound levels during the day, and especially on the weekend. Results also suggest that recording near the river bottom produced lower pseudo-noise levels than previous studies that recorded in the river water column.

New acoustical technology of sound absorption based on reverse horn

NASA Astrophysics Data System (ADS)

Zhang, Yong Yan; Wu, Jiu Hui; Cao, Song Hua; Cao, Pei; Zhao, Zi Ting

2016-12-01

In this paper, a novel reverse horn’s sound-absorption mechanism and acoustic energy focusing mechanism for low-frequency broadband are presented. Due to the alternation of the reverse horn’s thickness, the amplitude of the acoustic pressure propagated in the structure changes, which results in growing energy focused in the edge and in the reverse horn’s tip when the characteristic length is equal to or less than a wavelength and the incident wave is compressed. There are two kinds of methods adopted to realize energy dissipation. On the one hand, sound-absorbing materials are added in incident direction in order to overcome the badness of the reverse horn’s absorption in high frequency and improve the overall high-frequency and low-frequency sound-absorption coefficients; on the other hand, adding mass and film in its tip could result in mechanical energy converting into heat energy due to the coupled vibration of mass and the film. Thus, the reverse horn with film in the tip could realize better sound absorption for low-frequency broadband. These excellent properties could have potential applications in the one-dimensional absorption wedge and for the control of acoustic wave.

Sound absorption of microperforated panels inside compact acoustic enclosures

NASA Astrophysics Data System (ADS)

Yang, Cheng; Cheng, Li

2016-01-01

This paper investigates the sound absorption effect of microperforated panels (MPPs) in small-scale enclosures, an effort stemming from the recent interests in using MPPs for noise control in compact mechanical systems. Two typical MPP backing cavity configurations (an empty backing cavity and a honeycomb backing structure) are studied. Although both configurations provide basically the same sound absorption curves from standard impedance tube measurements, their in situ sound absorption properties, when placed inside a small enclosure, are drastically different. This phenomenon is explained using a simple system model based on modal analyses. It is shown that the accurate prediction of the in situ sound absorption of the MPPs inside compact acoustic enclosures requires meticulous consideration of the configuration of the backing cavity and its coupling with the enclosure in front. The MPP structure should be treated as part of the entire system, rather than an absorption boundary characterized by the surface impedance, calculated or measured in simple acoustic environment. Considering the spatial matching between the acoustic fields across the MPP, the possibility of attenuating particular enclosure resonances by partially covering the enclosure wall with a properly designed MPP structure is also demonstrated.

Differential Frequency Hopping (DFH) Modulation for Underwater Acoustic Communications and Networking

DTIC Science & Technology

2009-10-09

trains the coefficients c of a finite impulse response (FIR) filter by gradient descent. The coefficients at iteration k + 1 are computed with the update... absorption . Figure 9 shows the reflection loss as a function of grazing angle for this bottom model. Note that below 30◦ this bottom model predicts...less than 1 dB loss per ray bounce. 11 Figure 9: Jackson bottom reflection loss for sand at 15 kHz Absorption Loss The absorption loss in the medium was

Application of the Parabolic Approximation to Predict Acoustical Propagation in the Ocean.

ERIC Educational Resources Information Center

McDaniel, Suzanne T.

1979-01-01

A simplified derivation of the parabolic approximation to the acoustical wave equation is presented. Exact solutions to this approximate equation are compared with solutions to the wave equation to demonstrate the applicability of this method to the study of underwater sound propagation. (Author/BB)

Annotated Bibliography of Underwater Acoustic Research, 1942-1945.

DTIC Science & Technology

1983-11-02

by the condensation of lintite ("B" 71 Light Grey, Linings water vapor from the moist paper Inc., 914 South Wabash Ave., used in the instrument...a brief cadmium -plated steel, in order, are discussion of the effect of water most satisfactory for the temperature on maximum sound ranges

Advanced Systems for Monitoring Underwater Sounds

NASA Technical Reports Server (NTRS)

Lane, Michael; Van Meter, Steven; Gilmore, Richard Grant; Sommer, Keith

2007-01-01

The term "Passive Acoustic Monitoring System" (PAMS) describes a developmental sensing-and-data-acquisition system for recording underwater sounds. The sounds (more precisely, digitized and preprocessed versions from acoustic transducers) are subsequently analyzed by a combination of data processing and interpretation to identify and/or, in some cases, to locate the sources of those sounds. PAMS was originally designed to locate the sources such as fish of species that one knows or seeks to identify. The PAMS unit could also be used to locate other sources, for example, marine life, human divers, and/or vessels. The underlying principles of passive acoustic sensing and analyzing acoustic-signal data in conjunction with temperature and salinity data are not new and not unique to PAMS. Part of the uniqueness of the PAMS design is that it is the first deep-sea instrumentation design to provide a capability for studying soniferous marine animals (especially fish) over the wide depth range described below. The uniqueness of PAMS also lies partly in a synergistic combination of advanced sensing, packaging, and data-processing design features with features adapted from proven marine instrumentation systems. This combination affords a versatility that enables adaptation to a variety of undersea missions using a variety of sensors. The interpretation of acoustic data can include visual inspection of power-spectrum plots for identification of spectral signatures of known biological species or artificial sources. Alternatively or in addition, data analysis could include determination of relative times of arrival of signals at different acoustic sensors arrayed at known locations. From these times of arrival, locations of acoustic sources (and errors in those locations) can be estimated. Estimates of relative locations of sources and sensors can be refined through analysis of the attenuation of sound in the intervening water in combination with water-temperature and salinity data acquired by instrumentation systems other than PAMS. A PAMS is packaged as a battery-powered unit, mated with external sensors, that can operate in the ocean at any depth from 2 m to 1 km. A PAMS includes a pressure housing, a deep-sea battery, a hydrophone (which is one of the mating external sensors), and an external monitor and keyboard box. In addition to acoustic transducers, external sensors can include temperature probes and, potentially, underwater cameras. The pressure housing contains a computer that includes a hard drive, DC-to- DC power converters, a post-amplifier board, a sound card, and a universal serial bus (USB) 4-port hub.

Enhancement of acoustical performance of hollow tube sound absorber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Putra, Azma, E-mail: azma.putra@utem.edu.my; Khair, Fazlin Abd, E-mail: fazlinabdkhair@student.utem.edu.my; Nor, Mohd Jailani Mohd, E-mail: jai@utem.edu.my

This paper presents acoustical performance of hollow structures utilizing the recycled lollipop sticks as acoustic absorbers. The hollow cross section of the structures is arranged facing the sound incidence. The effects of different length of the sticks and air gap on the acoustical performance are studied. The absorption coefficient was measured using impedance tube method. Here it is found that improvement on the sound absorption performance is achieved by introducing natural kapok fiber inserted into the void between the hollow structures. Results reveal that by inserting the kapok fibers, both the absorption bandwidth and the absorption coefficient increase. For testmore » sample backed by a rigid surface, best performance of sound absorption is obtained for fibers inserted at the front and back sides of the absorber. And for the case of test sample with air gap, this is achieved for fibers introduced only at the back side of the absorber.« less

Enhancement of acoustical performance of hollow tube sound absorber

NASA Astrophysics Data System (ADS)

Putra, Azma; Khair, Fazlin Abd; Nor, Mohd Jailani Mohd

2016-03-01

This paper presents acoustical performance of hollow structures utilizing the recycled lollipop sticks as acoustic absorbers. The hollow cross section of the structures is arranged facing the sound incidence. The effects of different length of the sticks and air gap on the acoustical performance are studied. The absorption coefficient was measured using impedance tube method. Here it is found that improvement on the sound absorption performance is achieved by introducing natural kapok fiber inserted into the void between the hollow structures. Results reveal that by inserting the kapok fibers, both the absorption bandwidth and the absorption coefficient increase. For test sample backed by a rigid surface, best performance of sound absorption is obtained for fibers inserted at the front and back sides of the absorber. And for the case of test sample with air gap, this is achieved for fibers introduced only at the back side of the absorber.

Coupled Modeling of Hydrodynamics and Sound in Coastal Ocean for Renewable Ocean Energy Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Wen; Jung, Ki Won; Yang, Zhaoqing

An underwater sound model was developed to simulate sound propagation from marine and hydrokinetic energy (MHK) devices or offshore wind (OSW) energy platforms. Finite difference methods were developed to solve the 3D Helmholtz equation for sound propagation in the coastal environment. A 3D sparse matrix solver with complex coefficients was formed for solving the resulting acoustic pressure field. The Complex Shifted Laplacian Preconditioner (CSLP) method was applied to solve the matrix system iteratively with MPI parallelization using a high performance cluster. The sound model was then coupled with the Finite Volume Community Ocean Model (FVCOM) for simulating sound propagation generatedmore » by human activities, such as construction of OSW turbines or tidal stream turbine operations, in a range-dependent setting. As a proof of concept, initial validation of the solver is presented for two coastal wedge problems. This sound model can be useful for evaluating impacts on marine mammals due to deployment of MHK devices and OSW energy platforms.« less

Extraordinary absorption of sound in porous lamella-crystals.

PubMed

Christensen, J; Romero-García, V; Picó, R; Cebrecos, A; de Abajo, F J García; Mortensen, N A; Willatzen, M; Sánchez-Morcillo, V J

2014-04-14

We present the design of a structured material supporting complete absorption of sound with a broadband response and functional for any direction of incident radiation. The structure which is fabricated out of porous lamellas is arranged into a low-density crystal and backed by a reflecting support. Experimental measurements show that strong all-angle sound absorption with almost zero reflectance takes place for a frequency range exceeding two octaves. We demonstrate that lowering the crystal filling fraction increases the wave interaction time and is responsible for the enhancement of intrinsic material dissipation, making the system more absorptive with less material.

Extraordinary absorption of sound in porous lamella-crystals

PubMed Central

Christensen, J.; Romero-García, V.; Picó, R.; Cebrecos, A.; de Abajo, F. J. García; Mortensen, N. A.; Willatzen, M.; Sánchez-Morcillo, V. J.

2014-01-01

We present the design of a structured material supporting complete absorption of sound with a broadband response and functional for any direction of incident radiation. The structure which is fabricated out of porous lamellas is arranged into a low-density crystal and backed by a reflecting support. Experimental measurements show that strong all-angle sound absorption with almost zero reflectance takes place for a frequency range exceeding two octaves. We demonstrate that lowering the crystal filling fraction increases the wave interaction time and is responsible for the enhancement of intrinsic material dissipation, making the system more absorptive with less material. PMID:24728322

Imaging fall Chinook salmon redds in the Columbia River with a dual-frequency identification sonar

USGS Publications Warehouse

Tiffan, K.F.; Rondorf, D.W.; Skalicky, J.J.

2004-01-01

We tested the efficacy of a dual-frequency identification sonar (DIDSON) for imaging and enumeration of fall Chinook salmon Oncorhynchus tshawytscha redds in a spawning area below Bonneville Dam on the Columbia River. The DIDSON uses sound to form near-video-quality images and has the advantages of imaging in zero-visibility water and possessing a greater detection range and field of view than underwater video cameras. We suspected that the large size and distinct morphology of a fall Chinook salmon redd would facilitate acoustic imaging if the DIDSON was towed near the river bottom so as to cast an acoustic shadow from the tailspill over the redd pocket. We tested this idea by observing 22 different redds with an underwater video camera, spatially referencing their locations, and then navigating to them while imaging them with the DIDSON. All 22 redds were successfully imaged with the DIDSON. We subsequently conducted redd searches along transects to compare the number of redds imaged by the DIDSON with the number observed using an underwater video camera. We counted 117 redds with the DIDSON and 81 redds with the underwater video camera. Only one of the redds observed with the underwater video camera was not also documented by the DIDSON. In spite of the DIDSON's high cost, it may serve as a useful tool for enumerating fall Chinook salmon redds in conditions that are not conducive to underwater videography.

Hydrographic surveys of rivers and lakes using a multibeam echosounder mapping system

USGS Publications Warehouse

Huizinga, Richard J.; Heimann, David C.

2018-06-12

A multibeam echosounder is a type of sound navigation and ranging device that uses sound waves to “see” through even murky waters. Unlike a single beam echosounder (also known as a depth sounder or fathometer) that releases a single sound pulse in a single, narrow beam and “listens” for the return echo, a multibeam system emits a multidirectional radial beam to obtain information within a fan-shaped swath. The timing and direction of the returning sound waves provide detailed information on the depth of water and the shape of the river channel, lake bottom, or any underwater features of interest. This information has been used by the U.S. Geological Survey to efficiently generate high-resolution maps of river and lake bottoms.

Study on The Effectiveness of Egg Tray and Coir Fibre as A Sound Absorber

NASA Astrophysics Data System (ADS)

Kaamin, Masiri; Farah Atiqah Ahmad, Nor; Ngadiman, Norhayati; Kadir, Aslila Abdul; Razali, Siti Nooraiin Mohd; Mokhtar, Mardiha; Sahat, Suhaila

2018-03-01

Sound or noise pollution has become one major issues to the community especially those who lived in the urban areas. It does affect the activity of human life. This excessive noise is mainly caused by machines, traffic, motor vehicles and also any unwanted sounds that coming from outside and even from the inside of the building. Such as a loud music. Therefore, the installation of sound absorption panel is one way to reduce the noise pollution inside a building. The selected material must be a porous and hollow in order to absorb high frequency sound. This study was conducted to evaluate the potential of egg tray and coir fibre as a sound absorption panel. The coir fibre has a good coefficient value which make it suitable as a sound absorption material and can replace the traditional material; syntactic and wooden material. The combination of pyramid shape of egg tray can provide a large surface for uniform sound reflection. This study was conducted by using a panel with size 1 m x 1 m with a thickness of 6 mm. This panel consist of egg tray layer, coir fibre layer and a fabric as a wrapping for the aesthetic value. Room reverberation test has been carried to find the loss of reverberation time (RT). Result shows that, a reverberation time reading is on low frequency, which is 125 Hz to 1600 Hz. Within these frequencies, this panel can shorten the reverberation time of 5.63s to 3.60s. Hence, from this study, it can be concluded that the selected materials have the potential as a good sound absorption panel. The comparison is made with the previous research that used egg tray and kapok as a sound absorption panel.

Measurement and calculation of the sound absorption coefficient of pine wood charcoal

NASA Astrophysics Data System (ADS)

Suh, Jae Gap; Baik, Kyung min; Kim, Yong Tae; Jung, Sung Soo

2013-10-01

Although charcoal has been widely utilized for physical therapy and as a deodorant, water purifier, etc. due to its porous features, research on its role as a sound-absorbing material is rarely found. Thus, the sound absorption coefficients of pine wood charcoal were measured using an impedance tube and were compared with the theoretical predictions in the frequency range of 500˜ 5000 Hz. The theory developed in the current study only considers the lowest possible mode propagating along the air channels of the charcoal and shows good agreements with the measurements. As the frequency is increased, the sound absorption coefficients of pine wood charcoals also increase, but are lower than those of other commonly-used sound-absorbing materials.

Propagation and Signal Modeling

NASA Astrophysics Data System (ADS)

Jensen, Finn B.

The use of sound in the sea is ubiquitous: Apart from the military aspect of trying to detect an adversary’s mines and submarines, ship-mounted sonars measure water depth, ship speed, and the presence of fish shoals. Side-scan systems are used for mapping the bottom topography, sub-bottom profilers for getting information about the deeper layering, and other sonar systems for locating pipelines and cables on the seafloor. Sound is also used for navigating submerged vehicles, for underwater communications and for tracking marine mammals. Finally, in the realm of ‘acoustical oceanography’ and ‘ocean acoustic tomography,’ sound is used for measuring physical parameters of the ocean environment and for monitoring oceanic processes [1-6].

An investigation of the sound field above the audience in large lecture halls with a scale model.

PubMed

Kahn, D W; Tichy, J

1986-09-01

Measurements of steady-state sound pressure levels above the audience in large lecture halls show that the classical equation for predicting the sound pressure level is not accurate. The direct field above the seats was measured on a 1:10 scale model and was found to be dependent on the incidence angle and direction of sound propagation across the audience. The reverberant field above the seats in the model was calculated by subtracting the direct field from the measured total field and was found to be dependent on the magnitude and particularly on the placement of absorption. The decrease of sound pressure level versus distance in the total field depends on the angle (controlled by absorption placement) at which the strong reflections are incident upon the audience area. Sound pressure level decreases at a fairly constant rate with distance from the sound source in both the direct and reverberant field, and the decrease rate depends strongly on the absorption placement. The lowest rate of decay occurs when the side walls are absorptive, and both the ceiling and rear wall are reflective. These consequences are discussed with respect to prediction of speech intelligibility.

Speed of Sound and Ultrasound Absorption in Ionic Liquids.

PubMed

Dzida, Marzena; Zorębski, Edward; Zorębski, Michał; Żarska, Monika; Geppert-Rybczyńska, Monika; Chorążewski, Mirosław; Jacquemin, Johan; Cibulka, Ivan

2017-03-08

A complete review of the literature data on the speed of sound and ultrasound absorption in pure ionic liquids (ILs) is presented. Apart of the analysis of data published to date, the significance of the speed of sound in ILs is regarded. An analysis of experimental methods described in the literature to determine the speed of sound in ILs as a function of temperature and pressure is reported, and the relevance of ultrasound absorption in acoustic investigations is discussed. Careful attention was paid to highlight possible artifacts, and side phenomena related to the absorption and relaxation present in such measurements. Then, an overview of existing data is depicted to describe the temperature and pressure dependences on the speed of sound in ILs, as well as the impact of impurities in ILs on this property. A relation between ions structure and speeds of sound is presented by highlighting existing correlation and evaluative methods described in the literature. Importantly, a critical analysis of speeds of sound in ILs vs those in classical molecular solvents is presented to compare these two classes of compounds. The last part presents the importance of acoustic investigations for chemical engineering design and possible industrial applications of ILs.

Generation of Underwater Sound by a Moving High-Power Laser Source.

DTIC Science & Technology

1985-08-01

convolution 63 2. Laser beamwidth effects 67 3. Numerical predictions 69 V Table of Contents (Cont.) Page B. Experimental results 72 1. Pressure...source - II 53 17 Nerfield ef f ects: t as a ftunction of ro and cc 55 19 Nearfield effects : @max as a function of r. and a 56 • 20 Nearfield directivity...of a " photophone " or apparatus for the production of sound by light. Bell’s invention of the photophone was neglected for many years, but recently it

Application of a Modified Time Delay Spectrometry Technique in Modeling of Underwater Acoustic Propagation.

DTIC Science & Technology

1987-03-01

W.B. Anderson) 1 Keyport, Washington 98345 7. Director, David W. Taylor Naval Ships 1 and Development Center Detachment Puget Sound Attn: George...Monterey, California 93943-5000 Sa IIAME ’) F NDN1G, SPONSOQ;NG 8ab OF ,CE SvM9OL 9 PROCUJREMENT ,NSTR MET *DEN’ CATiON .,.M4[R ORCA ’.:ZAr ON j Iapplecaboe...analysis of sound propagating by multiple paths in an ocean at short ranges has been conducted using a Modified Time Delay Spectrometry (TDS) technique

The influence of flooring on environmental stressors: a study of three flooring materials in a hospital.

PubMed

Harris, Debra D

2015-01-01

Three flooring materials, terrazzo, rubber, and carpet tile, in patient unit corridors were compared for absorption of sound, comfort, light reflectance, employee perceptions and preferences, and patient satisfaction. Environmental stressors, such as noise and ergonomic factors, effect healthcare workers and patients, contributing to increased fatigue, anxiety and stress, decreased productivity, and patient safety and satisfaction. A longitudinal comparative cohort study comparing three types of flooring assessed sound levels, healthcare worker responses, and patient Hospital Consumer Assessment of Healthcare Providers and Systems (HCAHPS) ratings over 42 weeks. A linear mixed model analysis was conducted to determine significant differences between the means for participant responses and objective sound meter data during all three phases of the study. A significant difference was found for sound levels between flooring type for equivalent continuous sound levels. Carpet tile performed better for sound attenuation by absorption, reducing sound levels 3.14 dBA. Preferences for flooring materials changed over the course of the study. The HCAHPS ratings aligned with the sound meter data showing that patients perceived the noise levels to be lower with carpet tiles, improving patient satisfaction ratings. Perceptions for healthcare staff and patients were aligned with the sound meter data. Carpet tile provides sound absorption that affects sound levels and influences occupant's perceptions of environmental factors that contribute to the quality of the indoor environment. Flooring that provides comfort underfoot, easy cleanability, and sound absorption influence healthcare worker job satisfaction and patient satisfaction with their patient experience. © The Author(s) 2015.

Design And Construction of an Impedance Tube for Measuring Sound Absorptivity and Transmissibility of Materials Using Transfer Function Method

NASA Astrophysics Data System (ADS)

Gowda, Haarish Kapaninaikappa

Noise is defined as unwanted sound, when perceived in excess can cause many harmful effects such as annoyance, interference with speech, and hearing loss, hence there is a need to control noise in practical situations. Noise can be controlled actively and/or passively, here we discuss the passive noise control techniques. Passive noise control involves using energy dissipating or reflecting materials such as absorbers or barriers respectively. Damping and isolating materials are also used in eliminating structure-borne noise. These materials exhibit properties such as reflection, absorption and transmission loss when incidence is by a sound source. Thus, there is a need to characterize the acoustical properties of these materials for practical use. The theoretical background of the random incident sound absorption with reverberation room and normal incident sound absorption using impedance tube are well documented. The Transfer Matrix method for measuring transmission loss and absorption coefficient using impedance tube is very attractive since it is rather inexpensive and fast. In this research, a low-cost Impedance Tube is constructed using transfer function method to measure both absorption and transmissibility of materials. Equipment and measurement instruments available in the laboratory were used in the construction of the tube, adhering to cost-effectiveness. Care has been taken for precise construction of tube to ensure better measurement results. Further various samples varying from hard non-porous to soft porous materials were tested for absorption and sound transmission loss. Absorption values were also compared with reverberation room method with the available samples further ensuring the reliability of the newly constructed tube for future measurements.

Modeling and simulation of a counter-rotating turbine system for underwater vehicles

NASA Astrophysics Data System (ADS)

Wang, Xinping; Dang, Jianjun

2016-12-01

The structure of a counter-rotating turbine of an underwater vehicle is designed by adding the counter-rotating second-stage turbine disk after the conventional single-stage turbine. The available kinetic energy and the absorption power of the auxiliary system are calculated at different working conditions, and the results show that the power of the main engine and auxiliary system at the counter-rotating turbine system matches well with each other. The experimental simulation of the lubricating oil loop, fuel loop, and seawater loop are completed right before the technology scheme of the counter-rotating turbine system is proposed. The simulation results indicate that the hydraulic transmission system can satisfy the requirements for an underwater vehicle running at a steady sailing or variable working conditions.

Thin structured rigid body for acoustic absorption

NASA Astrophysics Data System (ADS)

Starkey, T. A.; Smith, J. D.; Hibbins, A. P.; Sambles, J. R.; Rance, H. J.

2017-01-01

We present a thin acoustic metamaterial absorber, comprised of only rigid metal and air, that gives rise to near unity absorption of airborne sound on resonance. This simple, easily fabricated, robust structure comprising a perforated metal plate separated from a rigid wall by a deeply subwavelength channel of air is an ideal candidate for a sound absorbing panel. The strong absorption in the system is attributed to the thermo-viscous losses arising from a sound wave guided between the plate and the wall, defining the subwavelength channel.

Sound absorption of a porous material with a perforated facing at high sound pressure levels

NASA Astrophysics Data System (ADS)

Peng, Feng

2018-07-01

A semi-empirical model is proposed to predict the sound absorption of an acoustical unit consisting of a rigid-porous material layer with a perforated facing under the normal incidence at high sound pressure levels (SPLs) of pure tones. The nonlinearity of the perforated facing and the porous material, and the interference between them are considered in the model. The sound absorptive performance of the acoustical unit is tested at different incident SPLs and in three typical configurations: 1) when the perforated panel (PP) directly contacts with the porous layer, 2) when the PP is separated from the porous layer by an air gap and 3) when an air cavity is set between the porous material and the hard backing wall. The test results agree well with the corresponding theoretical predictions. Moreover, the results show that the interference effect is correlated to the width of the air gap between the PP and the porous layer, which alters not only the linear acoustic impedance but also the nonlinear acoustic impedance of the unit and hence its sound absorptive properties.

Perfect sound insulation property of reclaimed waste tire rubber

NASA Astrophysics Data System (ADS)

Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

2016-03-01

This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

Underwater microwave ignition of hydrophobic thermite powder enabled by the bubble-marble effect

NASA Astrophysics Data System (ADS)

Meir, Yehuda; Jerby, Eli

2015-08-01

Highly energetic thermite reactions could be useful for a variety of combustion and material-processing applications, but their usability is yet limited by their hard ignition conditions. Furthermore, in virtue of their zero-oxygen balance, exothermic thermite reactions may also occur underwater. However, this feature is also hard to utilize because of the hydrophobic properties of the thermite powder, and its tendency to agglomerate on the water surface rather than to sink into the water. The recently discovered bubble-marble (BM) effect enables the insertion and confinement of a thermite-powder batch into water by a magnetic field. Here, we present a phenomenon of underwater ignition of a thermite-BM by localized microwaves. The thermite combustion underwater is observed in-situ, and its microwave absorption and optical spectral emission are detected. The vapour pressure generated by the thermite reaction is measured and compared to theory. The combustion products are examined ex-situ by X-ray photo-electron spectroscopy which verifies the thermite reaction. Potential applications of this underwater combustion effect are considered, e.g., for detonation, wet welding, thermal drilling, material processing, thrust generation, and composite-material production, also for other oxygen-free environments.

Underwater microwave ignition of hydrophobic thermite powder enabled by the bubble-marble effect

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meir, Yehuda; Jerby, Eli, E-mail: jerby@eng.tau.ac.il

Highly energetic thermite reactions could be useful for a variety of combustion and material-processing applications, but their usability is yet limited by their hard ignition conditions. Furthermore, in virtue of their zero-oxygen balance, exothermic thermite reactions may also occur underwater. However, this feature is also hard to utilize because of the hydrophobic properties of the thermite powder, and its tendency to agglomerate on the water surface rather than to sink into the water. The recently discovered bubble-marble (BM) effect enables the insertion and confinement of a thermite-powder batch into water by a magnetic field. Here, we present a phenomenon ofmore » underwater ignition of a thermite-BM by localized microwaves. The thermite combustion underwater is observed in-situ, and its microwave absorption and optical spectral emission are detected. The vapour pressure generated by the thermite reaction is measured and compared to theory. The combustion products are examined ex-situ by X-ray photo-electron spectroscopy which verifies the thermite reaction. Potential applications of this underwater combustion effect are considered, e.g., for detonation, wet welding, thermal drilling, material processing, thrust generation, and composite-material production, also for other oxygen-free environments.« less

An underwater optical wireless communication network

NASA Astrophysics Data System (ADS)

Arnon, Shlomi

2009-08-01

The growing need for underwater observation and sub-sea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, bio-geochemical, evolutionary and ecological changes in the sea, ocean and lake environments and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. We present models of three kinds of optical wireless communication links a) a line-of-sight link, b) a modulating retro-reflector link and c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered lighted it was possible to mitigate this decrease in some cases. We conclude from the analysis that a high data rate underwater optical wireless network is a feasible solution for emerging applications such as UUV to UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

Underwater optical wireless communication network

NASA Astrophysics Data System (ADS)

Arnon, Shlomi

2010-01-01

The growing need for underwater observation and subsea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, biogeochemical, evolutionary, and ecological changes in the sea, ocean, and lake environments, and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. Models are presented for three kinds of optical wireless communication links: (a) a line-of-sight link, (b) a modulating retroreflector link, and (c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered light it was possible to mitigate this decrease in some cases. It is concluded from the analysis that a high-data-rate underwater optical wireless network is a feasible solution for emerging applications such as UUV-to-UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

High Amplitude Acoustic Behavior of a Slit-Orifice Backed by a Cavity

NASA Technical Reports Server (NTRS)

Ahuja, K. K.; Gaeta, R. J., Jr.; DAgostino, M.; Jones, Mike (Technical Monitor)

2000-01-01

The objective of the study reported here was to acquire detailed acoustic data and limited and flow visualization data for numerical validation a new model of sound absorption by a very narrow rectangular slit backed by a cavity. The sound absorption model is being developed by Dr. C. K. W. Tam of Florida State University. This report documents normal incidence impedance measurements of a singular rectangular slit orifice with no mean flow. All impedance measurements are made within a 1.12 inch (28.5 mm) diameter impedance tube using the two-microphone method for several frequencies in the range 1000-6000Hz and incident sound pressure levels in the range 130 - 150 dB. In the interest of leaving the analysis of the data to the developers of more advanced analytical and computational models of sound absorption by narrow slits, we have refrained from giving our own explanations of the observed results, although many of the observed results can be explained using the classical explanations of sound absorption by orifices.

High Amplitude Acoustic Behavior of a Slit-Orifice Backed by a Cavity

NASA Technical Reports Server (NTRS)

Ahuja, K. K.; Gaeta, R. J., Jr.; DAgostino, M.

2000-01-01

The objective of this study was to acquire detailed acoustic data and limited flow visualization data for numerical validation of a new model of sound absorption by a very narrow rectangular slit backed by a cavity. The sound absorption model is that being developed by Dr. C. K. W. Tam of Florida State University. This report documents normal incidence impedance measurements of a singular rectangular slit orifice with no mean flow. All impedance measurements are made within a 1.12 inch (28.5 mm) diameter impedance tube using the two-microphone method for several frequencies in the range 1000 - 6000Hz and incident sound pressure levels in the range 130 - 150 dB. In the interest of leaving the analysis of the data to the developers of more advanced Analytical and computational models of sound absorption by narrow slits, we authors have refrained from giving our own explanations of the observed results, although many of the observed results can be explained using the classical understanding of sound absorption by orifices.

Flow noise of an underwater vector sensor embedded in a flexible towed array.

PubMed

Korenbaum, Vladimir I; Tagiltsev, Alexander A

2012-05-01

The objective of this work is to simulate the flow noise of a vector sensor embedded in a flexible towed array. The mathematical model developed, based on long-wavelength analysis of the inner space of a cylindrical multipole source, predicts the reduction of the flow noise of a vector sensor embedded in an underwater flexible towed array by means of intensimetric processing (cross-spectral density calculation of oscillatory velocity and sound-pressure-sensor responses). It is found experimentally that intensimetric processing results in flow noise reduction by 12-25 dB at mean levels and by 10-30 dB in fluctuations compared to a squared oscillatory velocity channel. The effect of flow noise suppression in the intensimetry channel relative to a squared sound pressure channel is observed, but only for frequencies above the threshold. These suppression values are 10-15 dB at mean noise levels and 3-6 dB in fluctuations. At towing velocities of 1.5-3 ms(-1) and an accumulation time of 98.3 s, the threshold frequency in fluctuations is between 30 and 45 Hz.

Using Gaussian mixture models to detect and classify dolphin whistles and pulses.

PubMed

Peso Parada, Pablo; Cardenal-López, Antonio

2014-06-01

In recent years, a number of automatic detection systems for free-ranging cetaceans have been proposed that aim to detect not just surfaced, but also submerged, individuals. These systems are typically based on pattern-recognition techniques applied to underwater acoustic recordings. Using a Gaussian mixture model, a classification system was developed that detects sounds in recordings and classifies them as one of four types: background noise, whistles, pulses, and combined whistles and pulses. The classifier was tested using a database of underwater recordings made off the Spanish coast during 2011. Using cepstral-coefficient-based parameterization, a sound detection rate of 87.5% was achieved for a 23.6% classification error rate. To improve these results, two parameters computed using the multiple signal classification algorithm and an unpredictability measure were included in the classifier. These parameters, which helped to classify the segments containing whistles, increased the detection rate to 90.3% and reduced the classification error rate to 18.1%. Finally, the potential of the multiple signal classification algorithm and unpredictability measure for estimating whistle contours and classifying cetacean species was also explored, with promising results.

A Q-Learning-Based Delay-Aware Routing Algorithm to Extend the Lifetime of Underwater Sensor Networks.

PubMed

Jin, Zhigang; Ma, Yingying; Su, Yishan; Li, Shuo; Fu, Xiaomei

2017-07-19

Underwater sensor networks (UWSNs) have become a hot research topic because of their various aquatic applications. As the underwater sensor nodes are powered by built-in batteries which are difficult to replace, extending the network lifetime is a most urgent need. Due to the low and variable transmission speed of sound, the design of reliable routing algorithms for UWSNs is challenging. In this paper, we propose a Q-learning based delay-aware routing (QDAR) algorithm to extend the lifetime of underwater sensor networks. In QDAR, a data collection phase is designed to adapt to the dynamic environment. With the application of the Q-learning technique, QDAR can determine a global optimal next hop rather than a greedy one. We define an action-utility function in which residual energy and propagation delay are both considered for adequate routing decisions. Thus, the QDAR algorithm can extend the network lifetime by uniformly distributing the residual energy and provide lower end-to-end delay. The simulation results show that our protocol can yield nearly the same network lifetime, and can reduce the end-to-end delay by 20-25% compared with a classic lifetime-extended routing protocol (QELAR).

Underwater, low-frequency noise in a coastal sea turtle habitat.

PubMed

Samuel, Y; Morreale, S J; Clark, C W; Greene, C H; Richmond, M E

2005-03-01

Underwater sound was recorded in one of the major coastal foraging areas for juvenile sea turtles in the Peconic Bay Estuary system in Long Island, New York. The recording season of the underwater environment coincided with the sea turtle activity season in an inshore area where there is considerable boating and recreational activity, especially during the summer between Independence Day and Labor Day. Within the range of sea turtle hearing, average noise pressure reached 110 dB during periods of high human activity and diminished proportionally, down to 80 dB, with decreasing human presence. Therefore, during much of the season when sea turtles are actively foraging in New York waters, their coastal habitats are flooded with underwater noise. During the period of highest human activity, average noise pressures within the range of frequencies heard by sea turtles were greater by over two orders of magnitude (26 dB) than during the lowest period of human activity. Sea turtles undoubtedly are exposed to high levels of noise, most of which is anthropogenic. Results suggest that continued exposure to existing high levels of pervasive anthropogenic noise in vital sea turtle habitats and any increase in noise could affect sea turtle behavior and ecology.

A Q-Learning-Based Delay-Aware Routing Algorithm to Extend the Lifetime of Underwater Sensor Networks

PubMed Central

Ma, Yingying; Su, Yishan; Li, Shuo; Fu, Xiaomei

2017-01-01

Underwater sensor networks (UWSNs) have become a hot research topic because of their various aquatic applications. As the underwater sensor nodes are powered by built-in batteries which are difficult to replace, extending the network lifetime is a most urgent need. Due to the low and variable transmission speed of sound, the design of reliable routing algorithms for UWSNs is challenging. In this paper, we propose a Q-learning based delay-aware routing (QDAR) algorithm to extend the lifetime of underwater sensor networks. In QDAR, a data collection phase is designed to adapt to the dynamic environment. With the application of the Q-learning technique, QDAR can determine a global optimal next hop rather than a greedy one. We define an action-utility function in which residual energy and propagation delay are both considered for adequate routing decisions. Thus, the QDAR algorithm can extend the network lifetime by uniformly distributing the residual energy and provide lower end-to-end delay. The simulation results show that our protocol can yield nearly the same network lifetime, and can reduce the end-to-end delay by 20–25% compared with a classic lifetime-extended routing protocol (QELAR). PMID:28753951

Sound Absorbers

NASA Astrophysics Data System (ADS)

Fuchs, H. V.; Möser, M.

Sound absorption indicates the transformation of sound energy into heat. It is, for instance, employed to design the acoustics in rooms. The noise emitted by machinery and plants shall be reduced before arriving at a workplace; auditoria such as lecture rooms or concert halls require a certain reverberation time. Such design goals are realised by installing absorbing components at the walls with well-defined absorption characteristics, which are adjusted for corresponding demands. Sound absorbers also play an important role in acoustic capsules, ducts and screens to avoid sound immission from noise intensive environments into the neighbourhood.

Assessing the Underwater Acoustics of the World's Largest Vibration Hammer (OCTA-KONG) and Its Potential Effects on the Indo-Pacific Humpbacked Dolphin (Sousa chinensis)

PubMed Central

Wang, Zhitao; Wu, Yuping; Duan, Guoqin; Cao, Hanjiang; Liu, Jianchang; Wang, Kexiong; Wang, Ding

2014-01-01

Anthropogenic noise in aquatic environments is a worldwide concern due to its potential adverse effects on the environment and aquatic life. The Hongkong-Zhuhai-Macao Bridge is currently under construction in the Pearl River Estuary, a hot spot for the Indo-Pacific humpbacked dolphin (Sousa chinensis) in China. The OCTA-KONG, the world's largest vibration hammer, is being used during this construction project to drive or extract steel shell piles 22 m in diameter. This activity poses a substantial threat to marine mammals, and an environmental assessment is critically needed. The underwater acoustic properties of the OCTA-KONG were analyzed, and the potential impacts of the underwater acoustic energy on Sousa, including auditory masking and physiological impacts, were assessed. The fundamental frequency of the OCTA-KONG vibration ranged from 15 Hz to 16 Hz, and the noise increments were below 20 kHz, with a dominant frequency and energy below 10 kHz. The resulting sounds are most likely detectable by Sousa over distances of up to 3.5 km from the source. Although Sousa clicks do not appear to be adversely affected, Sousa whistles are susceptible to auditory masking, which may negatively impact this species' social life. Therefore, a safety zone with a radius of 500 m is proposed. Although the zero-to-peak source level (SL) of the OCTA-KONG was lower than the physiological damage level, the maximum root-mean-square SL exceeded the cetacean safety exposure level on several occasions. Moreover, the majority of the unweighted cumulative source sound exposure levels (SSELs) and the cetacean auditory weighted cumulative SSELs exceeded the acoustic threshold levels for the onset of temporary threshold shift, a type of potentially recoverable auditory damage resulting from prolonged sound exposure. These findings may aid in the identification and design of appropriate mitigation methods, such as the use of air bubble curtains, “soft start” and “power down” techniques. PMID:25338113

Assessing the underwater acoustics of the world's largest vibration hammer (OCTA-KONG) and its potential effects on the Indo-Pacific humpbacked dolphin (Sousa chinensis).

PubMed

Wang, Zhitao; Wu, Yuping; Duan, Guoqin; Cao, Hanjiang; Liu, Jianchang; Wang, Kexiong; Wang, Ding

2014-01-01

Anthropogenic noise in aquatic environments is a worldwide concern due to its potential adverse effects on the environment and aquatic life. The Hongkong-Zhuhai-Macao Bridge is currently under construction in the Pearl River Estuary, a hot spot for the Indo-Pacific humpbacked dolphin (Sousa chinensis) in China. The OCTA-KONG, the world's largest vibration hammer, is being used during this construction project to drive or extract steel shell piles 22 m in diameter. This activity poses a substantial threat to marine mammals, and an environmental assessment is critically needed. The underwater acoustic properties of the OCTA-KONG were analyzed, and the potential impacts of the underwater acoustic energy on Sousa, including auditory masking and physiological impacts, were assessed. The fundamental frequency of the OCTA-KONG vibration ranged from 15 Hz to 16 Hz, and the noise increments were below 20 kHz, with a dominant frequency and energy below 10 kHz. The resulting sounds are most likely detectable by Sousa over distances of up to 3.5 km from the source. Although Sousa clicks do not appear to be adversely affected, Sousa whistles are susceptible to auditory masking, which may negatively impact this species' social life. Therefore, a safety zone with a radius of 500 m is proposed. Although the zero-to-peak source level (SL) of the OCTA-KONG was lower than the physiological damage level, the maximum root-mean-square SL exceeded the cetacean safety exposure level on several occasions. Moreover, the majority of the unweighted cumulative source sound exposure levels (SSELs) and the cetacean auditory weighted cumulative SSELs exceeded the acoustic threshold levels for the onset of temporary threshold shift, a type of potentially recoverable auditory damage resulting from prolonged sound exposure. These findings may aid in the identification and design of appropriate mitigation methods, such as the use of air bubble curtains, "soft start" and "power down" techniques.

Atmospheric absorption of high frequency noise and application to fractional-octave bands

NASA Technical Reports Server (NTRS)

Shields, F. D.; Bass, H. E.

1977-01-01

Pure tone sound absorption coefficients were measured at 1/12 octave intervals from 4 to 100 KHz at 5.5K temperature intervals between 255.4 and 310.9 K and at 10 percent relative humidity increments between 0 percent and saturation in a large cylindrical tube (i.d., 25.4 cm; length, 4.8 m). Special solid-dielectric capacitance transducers, one to generate bursts of sound waves and one to terminate the sound path and detect the tone bursts, were constructed to fit inside the tube. The absorption was measured by varying the transmitter receiver separation from 1 to 4 m and observing the decay of multiple reflections or change in amplitude of the first received burst. The resulting absorption was compared with that from a proposed procedure for computing sound absorption in still air. Absorption of bands of noise was numerically computed by using the pure tone results. The results depended on spectrum shape, on filter type, and nonlinearly on propagation distance. For some of the cases considered, comparison with the extrapolation of ARP-866A showed a difference as large as a factor of 2. However, for many cases, the absorption for a finite band was nearly equal to the pure tone absorption at the center frequency of the band. A recommended prediction procedure is described for 1/3 octave band absorption coefficients.

Non-Wovens as Sound Reducers

NASA Astrophysics Data System (ADS)

Belakova, D.; Seile, A.; Kukle, S.; Plamus, T.

2018-04-01

Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

Novel Application of Glass Fibers Recovered From Waste Printed Circuit Boards as Sound and Thermal Insulation Material

NASA Astrophysics Data System (ADS)

Sun, Zhixing; Shen, Zhigang; Ma, Shulin; Zhang, Xiaojing

2013-10-01

The aim of this study is to investigate the feasibility of using glass fibers, a recycled material from waste printed circuit boards (WPCB), as sound absorption and thermal insulation material. Glass fibers were obtained through a fluidized-bed recycling process. Acoustic properties of the recovered glass fibers (RGF) were measured and compared with some commercial sound absorbing materials, such as expanded perlite (EP), expanded vermiculite (EV), and commercial glass fiber. Results show that RGF have good sound absorption ability over the whole tested frequency range (100-6400 Hz). The average sound absorption coefficient of RGF is 0.86, which is prior to those of EP (0.81) and EV (0.73). Noise reduction coefficient analysis indicates that the absorption ability of RGF can meet the requirement of II rating for sound absorbing material according to national standard. The thermal insulation results show that RGF has a fair low thermal conductivity (0.046 W/m K), which is comparable to those of some insulation materials (i.e., EV, EP, and rock wool). Besides, an empirical dependence of thermal conductivity on material temperature was determined for RGF. All the results showed that the reuse of RGF for sound and thermal insulation material provided a promising way for recycling WPCB and obtaining high beneficial products.

Changing noise levels in a high CO2/lower pH ocean

NASA Astrophysics Data System (ADS)

Brewer, P. G.; Hester, K. C.; Peltzer, E. T.; Kirkwood, W. J.

2008-12-01

We show that ocean acidification from fossil fuel CO2 invasion and from increased respiration/reduced ventilation, has significantly reduced ocean sound absorption and thus increased ocean noise levels in the kHz frequency range. Below 10 kHz, sound absorption occurs due to well known chemical relaxations in the B(OH)3/B(OH)4- and HCO3-/CO32- systems. The pH dependence of these chemical relaxations results in decreased sound absorption (α = dB/km) as the ocean becomes more acidic from increased CO2 levels. The scale of surface ocean pH change today from the +105 ppmv change in atmospheric CO2 is about - 0.12 pH, resulting in frequency dependent decreases in sound absorption that now exceed 12% over pre- industrial. Under reasonable projections of future fossil fuel CO2 emissions and other sources a pH change of 0.3 units or more can be anticipated by mid-century, resulting in a decrease in α by almost 40%. Increases in water temperature have a smaller effect but also contribute to decreased sound absorption. Combining a lowering of 0.3 pH units with an increase of 3°C, α will decrease further to almost 45%. Ambient noise levels in the ocean within the auditory range critical for environmental, military, and economic interests are set to increase significantly due to the combined effects of decreased absorption and increasing sources from mankind's activities. Incorporation of sound absorption in modeling future ocean scenarios (R. Zeebe, personal communication) and long-term monitoring possibly with the aid of modern cabled observatories can give insights in how ocean noise will continue to change and its effect on groups such as marine mammals which communicate in the affected frequency range.

Sound absorption study of raw and expanded particulate vermiculites

NASA Astrophysics Data System (ADS)

Vašina, Martin; Plachá, Daniela; Mikeska, Marcel; Hružík, Lumír; Martynková, Gražyna Simha

2016-12-01

Expanded and raw vermiculite minerals were studied for their ability to absorb sound. Phase and structural characterization of the investigated vermiculites was found similar for both types, while morphology and surface properties vary. Sound waves reflect in wedge-like structure and get minimized, and later are absorbed totally. We found that thanks to porous character of expanded vermiculite the principle of absorption of sound into layered vermiculite morphology is analogous to principle of sound minimization in "anechoic chambers." It was found in this study that the best sound damping properties of the investigated vermiculites were in general obtained at higher powder bed heights and higher excitation frequencies.

Underwater noise assessment in the Gulf of Trieste (Northern Adriatic Sea, Italy) using an MSFD approach.

PubMed

Codarin, Antonio; Picciulin, Marta

2015-12-30

In the marine environment, underwater noise is one of the most widespread input of man-made energy. Recently, the European Commission has stressed the necessity of establishing threshold levels as a target for the descriptor 11.2.1 "Continuous low frequency sounds" in the Marine Strategy Framework Directive (MSFD). In 2012, a monthly underwater noise monitoring programme was conducted in the Gulf of Trieste (Northern Adriatic Sea, Italy); the collected acoustic samples (frequency range: 10-20,000 Hz) were analysed in the 1/3 octave bands. The stations have been further clustered following the 63 and 125 Hz bands noise levels. Average SPL levels resulted similar to those previously computed for proximate areas, indicating that the Adriatic Sea sub-region experiences high noise pressure in the marine waters. In its turn this claims for a scientific and technical international cooperation, as requested by the EU programme. No seasonal variation in local noise levels has been found. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hydrogel microphones for stealthy underwater listening

PubMed Central

Gao, Yang; Song, Jingfeng; Li, Shumin; Elowsky, Christian; Zhou, You; Ducharme, Stephen; Chen, Yong Mei; Zhou, Qin; Tan, Li

2016-01-01

Exploring the abundant resources in the ocean requires underwater acoustic detectors with a high-sensitivity reception of low-frequency sound from greater distances and zero reflections. Here we address both challenges by integrating an easily deformable network of metal nanoparticles in a hydrogel matrix for use as a cavity-free microphone. Since metal nanoparticles can be densely implanted as inclusions, and can even be arranged in coherent arrays, this microphone can detect static loads and air breezes from different angles, as well as underwater acoustic signals from 20 Hz to 3 kHz at amplitudes as low as 4 Pa. Unlike dielectric capacitors or cavity-based microphones that respond to stimuli by deforming the device in thickness directions, this hydrogel device responds with a transient modulation of electric double layers, resulting in an extraordinary sensitivity (217 nF kPa−1 or 24 μC N−1 at a bias of 1.0 V) without using any signal amplification tools. PMID:27554792

Influences of the Ratio of Polyol and MDI on the Acoustic Parameters of Polyurethane

NASA Astrophysics Data System (ADS)

Wang, Yonghua; Liu, Zheming; Wu, Haiquan; Zhang, Chengchun; Yu, Huadong; Ren, Luquan; Ichchou, Mohamed

2018-05-01

In this paper, the influence of different ratio of polyol and MDI on the absorption coefficient and acoustic parameters of polyurethane was studied. Ratio of 100:40 and 100:45 show the best sound absorption performance, and the change trend of transmission loss and sound absorption coefficient are opposite. The flow resistance increased with the increasing of the ratio of polyol and MDI, the greater the flow resistance, the worse the high frequency sound absorption property of the polyurethane. When the ratio of polyol and MDI keep 100:45, the minimum porosity of sample, the polyurethane porosity increase with the ratio of polyol and MDI increase.

Propagation of sound through the Earth's atmosphere. 1: Measurement of sound absorption in the air. 2: Measurement of ground impedance

NASA Technical Reports Server (NTRS)

Becher, J.; Meredith, R. W.; Zuckerwar, A. J.

1981-01-01

The fabrication of parts for the acoustic ground impedance meter was completed, and the instrument tested. Acoustic ground impedance meter, automatic data processing system, cooling system for the resonant tube, and final results of sound absorption in N2-H2O gas mixtures at elevated temperatures are described.

The vibroacoustic response and sound absorption performance of multilayer, microperforated rib-stiffened plates

NASA Astrophysics Data System (ADS)

Zhou, Haian; Wang, Xiaoming; Wu, Huayong; Meng, Jianbing

2017-10-01

The vibroacoustic response and sound absorption performance of a structure composed of multilayer plates and one rigid back wall are theoretically analyzed. In this structure, all plates are two-dimensional, microperforated, and periodically rib-stiffened. To investigate such a structural system, semianalytical models of one-layer and multilayer plate structures considering the vibration effects are first developed. Then approaches of the space harmonic method and Fourier transforms are applied to a one-layer plate, and finally the cascade connection method is utilized for a multilayer plate structure. Based on fundamental acoustic formulas, the vibroacoustic responses of microperforated stiffened plates are expressed as functions of a series of harmonic amplitudes of plate displacement, which are then solved by employing the numerical truncation method. Applying the inverse Fourier transform, wave propagation, and linear addition properties, the equations of the sound pressures and absorption coefficients for the one-layer and multilayer stiffened plates in physical space are finally derived. Using numerical examples, the effects of the most important physical parameters—for example, the perforation ratio of the plate, sound incident angles, and periodical rib spacing—on sound absorption performance are examined. Numerical results indicate that the sound absorption performance of the studied structure is effectively enhanced by the flexural vibration of the plate in water. Finally, the proposed approaches are validated by comparing the results of stiffened plates of the present work with solutions from previous studies.

The influence of sea ice, wind speed and marine mammals on Southern Ocean ambient sound.

PubMed

Menze, Sebastian; Zitterbart, Daniel P; van Opzeeland, Ilse; Boebel, Olaf

2017-01-01

This paper describes the natural variability of ambient sound in the Southern Ocean, an acoustically pristine marine mammal habitat. Over a 3-year period, two autonomous recorders were moored along the Greenwich meridian to collect underwater passive acoustic data. Ambient sound levels were strongly affected by the annual variation of the sea-ice cover, which decouples local wind speed and sound levels during austral winter. With increasing sea-ice concentration, area and thickness, sound levels decreased while the contribution of distant sources increased. Marine mammal sounds formed a substantial part of the overall acoustic environment, comprising calls produced by Antarctic blue whales ( Balaenoptera musculus intermedia ), fin whales ( Balaenoptera physalus ), Antarctic minke whales ( Balaenoptera bonaerensis ) and leopard seals ( Hydrurga leptonyx ). The combined sound energy of a group or population vocalizing during extended periods contributed species-specific peaks to the ambient sound spectra. The temporal and spatial variation in the contribution of marine mammals to ambient sound suggests annual patterns in migration and behaviour. The Antarctic blue and fin whale contributions were loudest in austral autumn, whereas the Antarctic minke whale contribution was loudest during austral winter and repeatedly showed a diel pattern that coincided with the diel vertical migration of zooplankton.

The influence of sea ice, wind speed and marine mammals on Southern Ocean ambient sound

NASA Astrophysics Data System (ADS)

Menze, Sebastian; Zitterbart, Daniel P.; van Opzeeland, Ilse; Boebel, Olaf

2017-01-01

This paper describes the natural variability of ambient sound in the Southern Ocean, an acoustically pristine marine mammal habitat. Over a 3-year period, two autonomous recorders were moored along the Greenwich meridian to collect underwater passive acoustic data. Ambient sound levels were strongly affected by the annual variation of the sea-ice cover, which decouples local wind speed and sound levels during austral winter. With increasing sea-ice concentration, area and thickness, sound levels decreased while the contribution of distant sources increased. Marine mammal sounds formed a substantial part of the overall acoustic environment, comprising calls produced by Antarctic blue whales (Balaenoptera musculus intermedia), fin whales (Balaenoptera physalus), Antarctic minke whales (Balaenoptera bonaerensis) and leopard seals (Hydrurga leptonyx). The combined sound energy of a group or population vocalizing during extended periods contributed species-specific peaks to the ambient sound spectra. The temporal and spatial variation in the contribution of marine mammals to ambient sound suggests annual patterns in migration and behaviour. The Antarctic blue and fin whale contributions were loudest in austral autumn, whereas the Antarctic minke whale contribution was loudest during austral winter and repeatedly showed a diel pattern that coincided with the diel vertical migration of zooplankton.

Operation and testing of Mark 10 Mod 3 underwater breathing apparatus

NASA Technical Reports Server (NTRS)

Milwee, W. I., Jr.

1972-01-01

Performance tests on a closed circuit, mixed gas underwater breathing apparatus are reported. The equipment is designed to provide a minimum diving duration of four hours at 1500 ft below sea surface; it senses oxygen partial pressure in the breathing gas mix and controls oxygen content of the breathing gas within narrow limits about a preset value. The breathing circuit subsystem provides respirable gas to the diver and removes carbon dioxide and moisture from the expired gas. Test results indicate undesirable variations in oxygen partial pressure with oxygen addition and insufficient carbon dioxide absorption.

Composite Sandwich Structures for Shock Mitigation and Energy Absorption

DTIC Science & Technology

2016-06-28

analysis of the blast performance of foam -core, composite sandwich panels was that on a per unit areal weight density basis, lighter and more crushable... foam cores offered greater blast resistance and energy absorption than the heavier and stronger foam cores. This was found to be the case even on an...absolute weight basis for cuNed sandwich panels and panels subjected to underwater blast. 15. SUBJECT TERMS composite; foam -core sandwich; blast

Great Ears: Low-Frequency Sensitivity Correlates in Land and Marine Leviathans.

PubMed

Ketten, D R; Arruda, J; Cramer, S; Yamato, M

2016-01-01

Like elephants, baleen whales produce low-frequency (LF) and even infrasonic (IF) signals, suggesting they may be particularly susceptible to underwater anthropogenic sound impacts. Analyses of computerized tomography scans and histologies of the ears in five baleen whale and two elephant species revealed that LF thresholds correlate with basilar membrane thickness/width and cochlear radii ratios. These factors are consistent with high-mass, low-stiffness membranes and broad spiral curvatures, suggesting that Mysticeti and Proboscidea evolved common inner ear adaptations over similar time scales for processing IF/LF sounds despite operating in different media.

Measurements of Operational Wind Turbine Noise in UK Waters.

PubMed

Cheesman, Samuel

2016-01-01

The effects of wind farm operational noise have not been addressed to the same extent as their construction methods such as piling and drilling of the foundations despite their long operational lifetimes compared with weeks of construction. The results of five postconstruction underwater sound-monitoring surveys on wind farms located throughout the waters of the British Isles are discussed. These wind farms consist of differing turbine power outputs, from 3 to 3.6 MW, and differing numbers of turbines. This work presents an overview of the results obtained and discusses both the levels and frequency components of the sound in several metrics.

Underwater Sound Levels at a Wave Energy Device Testing Facility in Falmouth Bay, UK.

PubMed

Garrett, Joanne K; Witt, Matthew J; Johanning, Lars

2016-01-01

Passive acoustic monitoring devices were deployed at FaBTest in Falmouth Bay, UK, a marine renewable energy device testing facility during trials of a wave energy device. The area supports considerable commercial shipping and recreational boating along with diverse marine fauna. Noise monitoring occurred during (1) a baseline period, (2) installation activity, (3) the device in situ with inactive power status, and (4) the device in situ with active power status. This paper discusses the preliminary findings of the sound recording at FabTest during these different activity periods of a wave energy device trial.

Underwater Sound Propagation Modeling Methods for Predicting Marine Animal Exposure.

PubMed

Hamm, Craig A; McCammon, Diana F; Taillefer, Martin L

2016-01-01

The offshore exploration and production (E&P) industry requires comprehensive and accurate ocean acoustic models for determining the exposure of marine life to the high levels of sound used in seismic surveys and other E&P activities. This paper reviews the types of acoustic models most useful for predicting the propagation of undersea noise sources and describes current exposure models. The severe problems caused by model sensitivity to the uncertainty in the environment are highlighted to support the conclusion that it is vital that risk assessments include transmission loss estimates with statistical measures of confidence.

Global Ocean Forecast System V3.0 Validation Test Report Addendum: Addition of the Diurnal Cycle

DTIC Science & Technology

2010-11-05

surface duct (e.g. Urick , 1983). When the solar radiation is zero during the night, the ocean surface cools and the associated mixing leads to the...HYCOMINCODA: Phase II. NRL Memo. Report, NRLIMRl7320--10-9236. Urick , R.J., 1983: Principles of underwater sound, 3rd Edition. Peninsula Publishing, Los

76 FR 80891 - Small Takes of Marine Mammals Incidental to Specified Activities; Cape Wind's High Resolution...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... 1, 2012, through December 31, 2012. ADDRESSES: A copy of the IHA and application are available by... species or stock through effects on annual rates of recruitment or survival.'' Section 101(a)(5)(D) of the...., increased underwater sound) generated during operation of the shallow-penetration and medium-penetration...

76 FR 54433 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to a...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-01

...: Effective September 5, 2011, through October 23, 2011. ADDRESSES: A copy of the IHA and application may be..., adversely affect the species or stock through effects on annual rates of recruitment or survival.'' Section... used. Acoustic stimuli (i.e., increased underwater sound) generated during the operation of the seismic...

Subwavelength structure for sound absorption from graphene oxide-doped polyvinylpyrrolidone nanofibers

NASA Astrophysics Data System (ADS)

Qamoshi, Khadijeh; Rasuli, Reza

2016-09-01

We study the sound absorption of the reinforced polyvinylpyrrolidone nanofibers with graphene oxide. It is shown that reinforced nanofibers can acquire impedance-matched surface to airborne sound at special frequencies. To obtain such surface, nanofibers were spun with polyvinylpyrrolidone polymer that was doped by graphene oxide with concentrations of 0, 6 and 12 wt%. It was found that fibers without graphene oxide were spun continuously and randomly, whereas by doping with graphene oxide, the mode of fibers is changed and some nodes form on the fibers coating. The sound absorption coefficient was measured by an impedance tube based on 105341-1 ISO standard. Measurements in the frequency range from 700 to 1600 Hz show that use of graphene oxide as a reinforcing phase increases sound absorption coefficient of the samples at a frequency ~1500 Hz up to ~40 %. Angular eigenfrequency and dissipation coefficient of the samples were obtained by impedance measurement for the prepared samples. Results show that doping the polymer with graphene oxide causes an increase in the angular eigenfrequency and the dissipation coefficient.

Microstructure based model for sound absorption predictions of perforated closed-cell metallic foams.

PubMed

Chevillotte, Fabien; Perrot, Camille; Panneton, Raymond

2010-10-01

Closed-cell metallic foams are known for their rigidity, lightness, thermal conductivity as well as their low production cost compared to open-cell metallic foams. However, they are also poor sound absorbers. Similarly to a rigid solid, a method to enhance their sound absorption is to perforate them. This method has shown good preliminary results but has not yet been analyzed from a microstructure point of view. The objective of this work is to better understand how perforations interact with closed-cell foam microstructure and how it modifies the sound absorption of the foam. A simple two-dimensional microstructural model of the perforated closed-cell metallic foam is presented and numerically solved. A rough three-dimensional conversion of the two-dimensional results is proposed. The results obtained with the calculation method show that the perforated closed-cell foam behaves similarly to a perforated solid; however, its sound absorption is modulated by the foam microstructure, and most particularly by the diameters of both perforation and pore. A comparison with measurements demonstrates that the proposed calculation method yields realistic trends. Some design guides are also proposed.

Impacts of underwater turbulence on acoustical and optical signals and their linkage.

PubMed

Hou, Weilin; Jarosz, Ewa; Woods, Sarah; Goode, Wesley; Weidemann, Alan

2013-02-25

Acoustical and optical signal transmission underwater is of vital interest for both civilian and military applications. The range and signal to noise during the transmission, as a function of system and water optical properties, in terms of absorption and scattering, determines the effectiveness of deployed electro-optical (EO) technology. The impacts from turbulence have been demonstrated to affect system performance comparable to those from particles by recent studies. This paper examines the impacts from underwater turbulence on both acoustic scattering and EO imaging degradation, and establishes a framework that can be used to correlate these. It is hypothesized here that underwater turbulence would influence the acoustic scattering cross section and the optical turbulence intensity coefficient in a similar manner. Data from a recent field campaign, Skaneateles Optical Turbulence Exercise (SOTEX, July, 2010) is used to examine the above relationship. Results presented here show strong correlation between the acoustic scattering cross-sections and the intensity coefficient related to the modulation transfer function of an EO imaging system. This significant finding will pave ways to utilize long range acoustical returns to predict EO system performance.

Sound absorption of a finite micro-perforated panel backed by a shunted loudspeaker.

PubMed

Tao, Jiancheng; Jing, Ruixiang; Qiu, Xiaojun

2014-01-01

Deep back cavities are usually required for micro-perforated panel (MPP) constructions to achieve good low frequency absorption. To overcome the problem, a close-box loudspeaker with a shunted circuit is proposed to substitute the back wall of the cavity of the MPP constructions to constitute a composite absorber. Based on the equivalent circuit model, the acoustic impedance of the shunted loudspeaker is formulated first, then a prediction model of the sound absorption of the MPP backed by shunted loudspeaker is developed by employing the mode solution of a finite size MPP coupled by an air cavity with an impendence back wall. The MPP absorbs mid to high frequency sound, and with properly adjusted electrical parameters of its shunted circuit, the shunted loudspeaker absorbs low frequency sound, so the composite absorber provides a compact solution to broadband sound control. Numerical simulations and experiments are carried out to validate the model.

Directional Reflective Surface Formed via Gradient-Impeding Acoustic Meta-Surfaces

PubMed Central

Song, Kyungjun; Kim, Jedo; Hur, Shin; Kwak, Jun-Hyuk; Lee, Seong-Hyun; Kim, Taesung

2016-01-01

Artificially designed acoustic meta-surfaces have the ability to manipulate sound energy to an extraordinary extent. Here, we report on a new type of directional reflective surface consisting of an array of sub-wavelength Helmholtz resonators with varying internal coiled path lengths, which induce a reflection phase gradient along a planar acoustic meta-surface. The acoustically reshaped reflective surface created by the gradient-impeding meta-surface yields a distinct focal line similar to a parabolic cylinder antenna, and is used for directive sound beamforming. Focused beam steering can be also obtained by repositioning the source (or receiver) off axis, i.e., displaced from the focal line. Besides flat reflective surfaces, complex surfaces such as convex or conformal shapes may be used for sound beamforming, thus facilitating easy application in sound reinforcement systems. Therefore, directional reflective surfaces have promising applications in fields such as acoustic imaging, sonic weaponry, and underwater communication. PMID:27562634

Local Probing Spinel and Perovskite Complex Magnetic Systems

NASA Astrophysics Data System (ADS)

Oliveira, Goncalo Nuno de Pinho

Noise is defined as unwanted sound, when perceived in excess can cause many harmful effects such as annoyance, interference with speech, and hearing loss, hence there is a need to control noise in practical situations. Noise can be controlled actively and/or passively, here we discuss the passive noise control techniques. Passive noise control involves using energy dissipating or reflecting materials such as absorbers or barriers respectively. Damping and isolating materials are also used in eliminating structure-borne noise. These materials exhibit properties such as reflection, absorption and transmission loss when incidence is by a sound source. Thus, there is a need to characterize the acoustical properties of these materials for practical use. The theoretical background of the random incident sound absorption with reverberation room and normal incident sound absorption using impedance tube are well documented. The Transfer Matrix method for measuring transmission loss and absorption coefficient using impedance tube is very attractive since it is rather inexpensive and fast. In this research, a low-cost Impedance Tube is constructed using transfer function method to measure both absorption and transmissibility of materials. Equipment and measurement instruments available in the laboratory were used in the construction of the tube, adhering to cost-effectiveness. Care has been taken for precise construction of tube to ensure better measurement results. Further various samples varying from hard non-porous to soft porous materials were tested for absorption and sound transmission loss. Absorption values were also compared with reverberation room method with the available samples further ensuring the reliability of the newly constructed tube for future measurements.

Song copying by humpback whales: themes and variations.

PubMed

Mercado, Eduardo; Herman, Louis M; Pack, Adam A

2005-04-01

Male humpback whales (Megaptera novaeangliae) produce long, structured sequences of sound underwater, commonly called "songs." Humpbacks progressively modify their songs over time in ways that suggest that individuals are copying song elements that they hear being used by other singers. Little is known about the factors that determine how whales learn from their auditory experiences. Song learning in birds is better understood and appears to be constrained by stable core attributes such as species-specific sound repertoires and song syntax. To clarify whether similar constraints exist for song learning by humpbacks, we analyzed changes over 14 years in the sounds used by humpback whales singing in Hawaiian waters. We found that although the properties of individual sounds within songs are quite variable over time, the overall distribution of certain acoustic features within the repertoire appears to be stable. In particular, our findings suggest that species-specific constraints on temporal features of song sounds determine song form, whereas spectral variability allows whales to flexibly adapt song elements.

Antimasking aspects of harp seal (Pagophilus groenlandicus) underwater vocalizations.

PubMed

Serrano, Arturo; Terhune, John M

2002-12-01

Underwater sounds are very important in social communication of harp seals (Pagophilus groenlandicus) because they are the main means of long- and short-distance communication. Individual harp seals must try to avoid being masked and emit only those calls that will benefit them. Underwater vocalizations of harp seals were recorded during the breeding season. The physical characteristics associated with antimasking attributes of 16 call types were examined. Rising frequency or increasing amplitude within calls were not common. Most of the calls ended abruptly (range 145-966 dB/s), but call onset was more gradual. At high calling rates (95.1-135 calls/min) there were significantly more calls overlapping temporally than at medium (75.1-95 calls/min) or low (35-75 calls/min) calling rates, but even at the highest calling rates, 79.1% of the calls were not overlapped. When 2, 3, or 4 calls overlapped, there were significantly fewer frequency separations of less than 1/3 octave than would be expected by chance. This is important because sounds that are separated by less than 1/3 octave likely mask each other. When 2-4 calls are occurring simultaneously, only 4.5% to 14.2% are masked by virtue of being within 1/3 octave from their nearest neighbor. None of the overlappping calls was of the same type. This suggests that the seals are actively listening to each other's calls and are not randomly using the different call types. Harp seals use frequency and temporal separation in conjunction with a wide vocal repertoire to avoid masking each other.

Antimasking aspects of harp seal (Pagophilus groenlandicus) underwater vocalizations

NASA Astrophysics Data System (ADS)

Serrano, Arturo; Terhune, John M.

2002-12-01

Underwater sounds are very important in social communication of harp seals (Pagophilus groenlandicus) because they are the main means of long- and short-distance communication. Individual harp seals must try to avoid being masked and emit only those calls that will benefit them. Underwater vocalizations of harp seals were recorded during the breeding season. The physical characteristics associated with antimasking attributes of 16 call types were examined. Rising frequency or increasing amplitude within calls were not common. Most of the calls ended abruptly (range 145-966 dB/s), but call onset was more gradual. At high calling rates (95.1-135 calls/min) there were significantly more calls overlapping temporally than at medium (75.1-95 calls/min) or low (35-75 calls/min) calling rates, but even at the highest calling rates, 79.1% of the calls were not overlapped. When 2, 3, or 4 calls overlapped, there were significantly fewer frequency separations of less than 1/3 octave than would be expected by chance. This is important because sounds that are separated by less than 1/3 octave likely mask each other. When 2-4 calls are occurring simultaneously, only 4.5% to 14.2% are masked by virtue of being within 1/3 octave from their nearest neighbor. None of the overlappping calls was of the same type. This suggests that the seals are actively listening to each other's calls and are not randomly using the different call types. Harp seals use frequency and temporal separation in conjunction with a wide vocal repertoire to avoid masking each other.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyazaki, Tadakuni; Harashima, Akira; Nakatani, Yukihiro

Coral reefs are the major sites for photo-synthesis and calcification in the present ocean. Estimating the production rate of calcification by the coral reefs or investigating the sink/source mechanism of CO{sub 2} by the coral reefs in the ocean, the distribution of the coral reefs in the world wide must be identified. Measuring the spectral signatures of underwater coral reefs and mapping of coral reefs by satellite remote sensing are described. The spectral signatures of different species of the coral reefs were measured using a spectroradiometer at off Kuroshima Island, Okinawa, Japan and investigated spectral difference between different species ofmore » the coral reefs. As well as the field experiments, laboratory experiments for measuring the spectral signatures of 9 different species of coral reefs were carried out with the same spectroradiometer. The spectral reflectance of each coral reef showed a significant result that a narrow absorption band exists in the spectral region between 660 and 680 nm, and very strong spectral reflectance from about 700 nm towards the longer wavelength range. On the other hand, absorption and the high reflectance region were not observed from the bottom sands or bare rocks underwater. These experiments suggested that there is a significant spectral difference between coral reefs and bottom sands or bare rocks and so the best spectral range for separating the coral reefs from other underwater objects in the ocean would be between 700 and 800 nm. As well as the basic spectral measurement either in the field or at the laboratory, SPOT satellite imageries were used to classify the underwater coral reefs. Classification methods used here were the principal component analysis, and the maximum likelihood. Finally, the evaluation of classification method for extracting the coral reefs was introduced.« less

Simplified procedure for computing the absorption of sound by the atmosphere

DOT National Transportation Integrated Search

2007-10-31

This paper describes a study that resulted in the development of a simplified : method for calculating attenuation by atmospheric-absorption for wide-band : sounds analyzed by one-third octave-band filters. The new method [referred to : herein as the...

Simulation of an active underwater imaging through a wavy sea surface

NASA Astrophysics Data System (ADS)

Gholami, Ali; Saghafifar, Hossein

2018-06-01

A numerical simulation for underwater imaging through a wavy sea surface has been done. We have used a common approach to model the sea surface elevation and its slopes as an important source of image disturbance. The simulation algorithm is based on a combination of ray tracing and optical propagation, which has taken to different approaches for downwelling and upwelling beams. The nature of randomly focusing and defocusing property of surface waves causes a fluctuated irradiance distribution as an illuminating source of immersed object, while it gives rise to a great disturbance on the image through a coordinate change of image pixels. We have also used a modulation transfer function based on Well's small angle approximations to consider the underwater optical properties effect on the transferring of the image. As expected, the absorption effect reduces the light intensity and scattering decreases image contrast by blurring the image.

Behavioral responses of a harbor porpoise (Phocoena phocoena) to playbacks of broadband pile driving sounds.

PubMed

Kastelein, Ronald A; van Heerden, Dorianne; Gransier, Robin; Hoek, Lean

2013-12-01

The high under-water sound pressure levels (SPLs) produced during pile driving to build offshore wind turbines may affect harbor porpoises. To estimate the discomfort threshold of pile driving sounds, a porpoise in a quiet pool was exposed to playbacks (46 strikes/min) at five SPLs (6 dB steps: 130-154 dB re 1 μPa). The spectrum of the impulsive sound resembled the spectrum of pile driving sound at tens of kilometers from the pile driving location in shallow water such as that found in the North Sea. The animal's behavior during test and baseline periods was compared. At and above a received broadband SPL of 136 dB re 1 μPa [zero-peak sound pressure level: 151 dB re 1 μPa; t90: 126 ms; sound exposure level of a single strike (SELss): 127 dB re 1 μPa(2) s] the porpoise's respiration rate increased in response to the pile driving sounds. At higher levels, he also jumped out of the water more often. Wild porpoises are expected to move tens of kilometers away from offshore pile driving locations; response distances will vary with context, the sounds' source level, parameters influencing sound propagation, and background noise levels. Copyright © 2013 Elsevier Ltd. All rights reserved.

Transfer matrix modeling and experimental validation of cellular porous material with resonant inclusions.

PubMed

Doutres, Olivier; Atalla, Noureddine; Osman, Haisam

2015-06-01

Porous materials are widely used for improving sound absorption and sound transmission loss of vibrating structures. However, their efficiency is limited to medium and high frequencies of sound. A solution for improving their low frequency behavior while keeping an acceptable thickness is to embed resonant structures such as Helmholtz resonators (HRs). This work investigates the absorption and transmission acoustic performances of a cellular porous material with a two-dimensional periodic arrangement of HR inclusions. A low frequency model of a resonant periodic unit cell based on the parallel transfer matrix method is presented. The model is validated by comparison with impedance tube measurements and simulations based on both the finite element method and a homogenization based model. At the HR resonance frequency (i) the transmission loss is greatly improved and (ii) the sound absorption of the foam can be either decreased or improved depending on the HR tuning frequency and on the thickness and properties of the host foam. Finally, the diffuse field sound absorption and diffuse field sound transmission loss performance of a 2.6 m(2) resonant cellular material are measured. It is shown that the improvements observed at the Helmholtz resonant frequency on a single cell are confirmed at a larger scale.

Towards Enhanced Underwater Lidar Detection via Source Separation

NASA Astrophysics Data System (ADS)

Illig, David W.

Interest in underwater optical sensors has grown as technologies enabling autonomous underwater vehicles have been developed. Propagation of light through water is complicated by the dual challenges of absorption and scattering. While absorption can be reduced by operating in the blue-green region of the visible spectrum, reducing scattering is a more significant challenge. Collection of scattered light negatively impacts underwater optical ranging, imaging, and communications applications. This thesis concentrates on the ranging application, where scattering reduces operating range as well as range accuracy. The focus of this thesis is on the problem of backscatter, which can create a "clutter" return that may obscure submerged target(s) of interest. The main contributions of this thesis are explorations of signal processing approaches to increase the separation between the target and backscatter returns. Increasing this separation allows detection of weak targets in the presence of strong scatter, increasing both operating range and range accuracy. Simulation and experimental results will be presented for a variety of approaches as functions of water clarity and target position. This work provides several novel contributions to the underwater lidar field: 1. Quantification of temporal separation approaches: While temporal separation has been studied extensively, this work provides a quantitative assessment of the extent to which both high frequency modulation and spatial filter approaches improve the separation between target and backscatter. 2. Development and assessment of frequency separation: This work includes the first frequency-based separation approach for underwater lidar, in which the channel frequency response is measured with a wideband waveform. Transforming to the time-domain gives a channel impulse response, in which target and backscatter returns may appear in unique range bins and thus be separated. 3. Development and assessment of statistical separation: The first investigations of statistical separation approaches for underwater lidar are presented. By demonstrating that target and backscatter returns have different statistical properties, a new separation axis is opened. This work investigates and quantifies performance of three statistical separation approaches. 4. Application of detection theory to underwater lidar: While many similar applications use detection theory to assess performance, less development has occurred in the underwater lidar field. This work applies these concepts to statistical separation approaches, providing another perspective in which to assess performance. In addition, by using detection theory approaches, statistical metrics can be used to associate a level of confidence in each ranging measurement. 5. Preliminary investigation of forward scatter suppression: If backscatter is sufficiently suppressed, forward scattering becomes a performance-limiting factor. This work presents a proof-of-concept demonstration of the potential for statistical separation approaches to suppress both forward and backward scatter. These results provide a demonstration of the capability that signal processing has to improve separation between target and backscatter. Separation capability improves in the transition from temporal to frequency to statistical separation approaches, with the statistical separation approaches improving target detection sensitivity by as much as 30 dB. Ranging and detection results demonstrate the enhanced performance this would allow in ranging applications. This increased performance is an important step in moving underwater lidar capability towards the requirements of the next generation of sensors.

An Autonomous Underwater Recorder Based on a Single Board Computer.

PubMed

Caldas-Morgan, Manuel; Alvarez-Rosario, Alexander; Rodrigues Padovese, Linilson

2015-01-01

As industrial activities continue to grow on the Brazilian coast, underwater sound measurements are becoming of great scientific importance as they are essential to evaluate the impact of these activities on local ecosystems. In this context, the use of commercial underwater recorders is not always the most feasible alternative, due to their high cost and lack of flexibility. Design and construction of more affordable alternatives from scratch can become complex because it requires profound knowledge in areas such as electronics and low-level programming. With the aim of providing a solution; a well succeeded model of a highly flexible, low-cost alternative to commercial recorders was built based on a Raspberry Pi single board computer. A properly working prototype was assembled and it demonstrated adequate performance levels in all tested situations. The prototype was equipped with a power management module which was thoroughly evaluated. It is estimated that it will allow for great battery savings on long-term scheduled recordings. The underwater recording device was successfully deployed at selected locations along the Brazilian coast, where it adequately recorded animal and manmade acoustic events, among others. Although power consumption may not be as efficient as that of commercial and/or micro-processed solutions, the advantage offered by the proposed device is its high customizability, lower development time and inherently, its cost.

Sound propagation and absorption in foam - A distributed parameter model.

NASA Technical Reports Server (NTRS)

Manson, L.; Lieberman, S.

1971-01-01

Liquid-base foams are highly effective sound absorbers. A better understanding of the mechanisms of sound absorption in foams was sought by exploration of a mathematical model of bubble pulsation and coupling and the development of a distributed-parameter mechanical analog. A solution by electric-circuit analogy was thus obtained and transmission-line theory was used to relate the physical properties of the foams to the characteristic impedance and propagation constants of the analog transmission line. Comparison of measured physical properties of the foam with values obtained from measured acoustic impedance and propagation constants and the transmission-line theory showed good agreement. We may therefore conclude that the sound propagation and absorption mechanisms in foam are accurately described by the resonant response of individual bubbles coupled to neighboring bubbles.

Atmospheric Propagation

NASA Technical Reports Server (NTRS)

Embleton, Tony F. W.; Daigle, Gilles A.

1991-01-01

Reviewed here is the current state of knowledge with respect to each basic mechanism of sound propagation in the atmosphere and how each mechanism changes the spectral or temporal characteristics of the sound received at a distance from the source. Some of the basic processes affecting sound wave propagation which are present in any situation are discussed. They are geometrical spreading, molecular absorption, and turbulent scattering. In geometrical spreading, sound levels decrease with increasing distance from the source; there is no frequency dependence. In molecular absorption, sound energy is converted into heat as the sound wave propagates through the air; there is a strong dependence on frequency. In turbulent scattering, local variations in wind velocity and temperature induce fluctuations in phase and amplitude of the sound waves as they propagate through an inhomogeneous medium; there is a moderate dependence on frequency.

Temporal patterns in marine mammal sounds from long-term broadband recordings

NASA Astrophysics Data System (ADS)

Hildebrand, John A.; Wiggins, Sean; Oleson, Erin; Sirovic, Ana; Munger, Lisa; Soldevilla, Melissa; Burtenshaw, Jessica

2005-09-01

Recent advances in the technology for long-term underwater acoustic recording provide new data on the temporal patterns of marine mammal sounds. Autonomous acoustic recordings are now being made with broad frequency bandwidth up to 200-kHz sampling rates. These data allow sound recording from most marine mammal species, including, for instance, the echolocation clicks of odontocetes. Large data storage capacity up to 1280 Gbytes allow these recordings to be conducted over long time periods for study of diel and seasonal calling patterns. Examples will be presented of temporal patterns from long-term recordings collected in four regions: the Bering Sea, offshore southern California, the Gulf of California, and the Southern Ocean. These data provide new insight on marine mammal distribution, seasonality, and behavior.

Underwater sounds near a fuel receiving facility in western Hong Kong: relevance to dolphins.

PubMed

Würsig, B; Greene, C R

2002-08-01

Western Hong Kong is home to two species of marine mammals: Indo-Pacific humpbacked dolphins (Sousa chinensis) and finless porpoises (Neophocaena phocaenoides). Both are threatened in many parts of their range in southeast Asia [for example, International Biological Research Institute Reports 9 (1997), 41; Asian Marine Biology 14 (1997) 111]. In 1998, when the new Hong Kong International Airport opened in western Hong Kong, small tankers (about 100 m long, cargo capacity about 6300 metric tons) began delivering fuel to the Aviation Fuel Receiving Facility (AFRF) just off Sha Chau Island, north of the airport. Calibrated sound recordings were taken over a 4-day period from a quiet, anchored boat at distances 80-2000 m from aviation fuel delivery activities at the AFRF. From the recordings, 143 sections were selected for analysis. Narrowband spectral densities on the sound pressures were computed, and one-third octave band levels were derived for center frequencies from 10 to 16,000 Hz. Broadband levels, viz. 10-20,000 Hz. were also computed. The results showed that the Sha Chau area is normally noisy underwater, with the lowest broadband levels measured corresponding to those expected during a storm at sea (sea state 6). This background noise is believed to come largely from heavy vessel traffic in the Urmston Road to the north and east of Sha Chau and from vessels in the Pearl River Estuary to the West. The sound levels from the AFRF tankers are comparable to the levels measured from similar- and smaller-sized supply vessels supporting offshore oil exploration. The strongest sounds recorded were from a tanker leaving the AFRF at distance 100 m from the hydrophone, for which the one-third octave band level at 100 Hz was 141 dB re 1 microPa (spectrum level 127 dB re 1 microPa2/Hz) and the 10-20,000 Hz broadband level was 146 dB. At distances of 100 m or more and frequencies above 300 Hz, the one-third octave band levels were less than 130 dB (spectrum level 111 dB re 1 microPa2/Hz) and decreased with increasing frequency and distance. At distances greater than about 500 m, AFRF-associated sounds were negligible, masked by the generally high noise level of the area and attenuated by poor transmission in the very shallow water (<10 m). Because it is believed that humpbacked dolphins and finless porpoises are not very sensitive to sounds below 300 Hz, the Airport Authority Hong Kong (AA) stipulated that dedicated terminal vessels not radiate underwater sounds at spectrum levels greater than 110 dB re 1 microPa2/Hz at frequencies above 300 Hz and distances greater than 300 m. The spectrum levels at 300 Hz and higher frequencies of sounds from the tankers arriving, departing, or off-loading at AFRF were less than 110 dB re 1 microPa2/Hz even at distances of 200 m or less. The AA stipulation was met. However, it is presently unknown whether the generally strong noise levels of western Hong Kong inhibit acoustically based feeding and communication, or result in increased stress or permanent shifts in hearing thresholds.

Navy Training Lands Sustainability: Initiation Decision Report

DTIC Science & Technology

2004-06-01

Health Promotion and Preventative Medicine CLF Combat Logistics Force CMAQ Community Multiscale Air Quality CNEL Community Noise Equivalent Level...Environmental Consequences of Underwater Sound EDQW (DoD) Environmental Data Quality Workgroup EEZ Exclusive Economic Zone EFHA Essential Fish Habitat...Conservation Management Act established a 200-mile fishery conservation zone, which is now known as the Exclusive Economic Zone (EEZ), and established

Underwater Acoustic Carbon Nanotube Thermophone

DTIC Science & Technology

2016-09-23

temperature radiation by the carbon nanotube material chip. [0033] Furthermore, the wooden spacers 20 provide heat insulation between the carbon nanotube...based on an energy conversion of heat to sound. (2) Description of the Prior Art [0004] The principle of thermal acoustic transduction is that when...alternating current is passed through a comparatively thin transducer; periodic heating takes place in the conductor following variations in current

Underwater Sound Scattering by Marine Organisms. A Review,

DTIC Science & Technology

1979-08-01

play the dominant scattering role in different seasons . 2.2 Correlation of Acoustic Reverberation Measurements with the Geographic Distribution of...to scattering beneath a floating ice station on the Beaufort Sea. Plankton net hauls indicated that accumulations of the thecostomatous pteropod ...and in the combined upper layer at night. Of these, the siphonophore, Ablyopsis tetragona, pteropod Cymbulia sp.,euphausiids, Thysanopoda sp. and

Human Bioresponse to Low-Frequency Underwater Sound

DTIC Science & Technology

2009-02-02

polyhedrons. Figure 4.2 shows a vertical array of two alveolar duct units. Fung focused only on the morphometric accuracy of this geometrical ...created that includes idealized geometrical representations of the lungs, ribs, trachea, bronchiole tubes, spine, sternum, and a generalized...clusters subjected to different excitations and geometric constraints will be shown. With the objective of developing an effective medium model that

76 FR 30552 - Taking and Importing Marine Mammals: U.S. Navy Training in the Virginia Capes Range Complex and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-26

... involving underwater detonations that will occur over the course of the 5-year rules, and indicate that... within the analyzed and authorized limits. Since the issuance of these rules, the Navy realized that... of explosives and sound sources to be used (e.g., number of events or explosive detonations) over the...

Investigating trends in acoustics research from 1970-1999.

PubMed

Viator, J A; Pestorius, F M

2001-05-01

Text data mining is a burgeoning field in which new information is extracted from existing text databases. Computational methods are used to compare relationships between database elements to yield new information about the existing data. Text data mining software was used to determine research trends in acoustics for the years 1970, 1980, 1990, and 1999. Trends were indicated by the number of published articles in the categories of acoustics using the Journal of the Acoustical Society of America (JASA) as the article source. Research was classified using a method based on the Physics and Astronomy Classification Scheme (PACS). Research was further subdivided into world regions, including North and South America, Eastern and Western Europe, Asia, Africa, Middle East, and Australia/New Zealand. In order to gauge the use of JASA as an indicator of international acoustics research, three subjects, underwater sound, nonlinear acoustics, and bioacoustics, were further tracked in 1999, using all journals in the INSPEC database. Research trends indicated a shift in emphasis of certain areas, notably underwater sound, audition, and speech. JASA also showed steady growth, with increasing participation by non-US authors, from about 20% in 1970 to nearly 50% in 1999.

Time reversal technique for gas leakage detection.

PubMed

Maksimov, A O; Polovinka, Yu A

2015-04-01

The acoustic remote sensing of subsea gas leakage traditionally uses sonars as active acoustic sensors and hydrophones picking up the sound generated by a leak as passive sensors. When gas leaks occur underwater, bubbles are produced and emit sound at frequencies intimately related to their sizes. The experimental implementation of an acoustic time-reversal mirror (TRM) is now well established in underwater acoustics. In the basic TRM experiment, a probe source emits a pulse that is received on an array of sensors, time reversed, and re-emitted. After time reversal, the resulting field focuses back at the probe position. In this study, a method for enhancing operation of the passive receiving system has been proposed by using it in the regime of TRM. Two factors, the local character of the acoustic emission signal caused by the leakage and a resonant nature of the bubble radiation at their birth, make particularly effective scattering with the conjugate wave (CW). Analytical calculations are performed for the scattering of CW wave on a single bubble when CW is formed by bubble birthing wail received on an array, time reversed, and re-emitted. The quality of leakage detection depends on the spatio-temporal distribution of ambient noise.

Pinniped bioacoustics: Atmospheric and hydrospheric signal production, reception, and function

NASA Astrophysics Data System (ADS)

Schusterman, Ronald J.; Kastak, David; Reichmuth Kastak, Colleen; Holt, Marla; Southall, Brandon L.

2004-05-01

There is no convincing evidence that any of the 33 pinniped species evolved acoustic specializations for echolocation. However, all species produce and localize signals amphibiously in different communicative contexts. In the setting of sexual selection, aquatic mating male phocids and walruses tend to emit underwater calls, while male otariids and phocids that breed terrestrially emit airborne calls. Signature vocalizations are widespread among pinnipeds. There is evidence that males use signature threat calls, and it is possible that vocal recognition may be used by territorial males to form categories consisting of neighbors and strangers. In terms of mother-offspring recognition, both otariid females and their pups use acoustical cues for mutual recognition. In contrast, reunions between phocid females and their dependent pups depend mostly on pup vocalizations. In terms of signal reception, audiometric studies show that otariids are highly sensitive to aerial sounds but slightly less sensitive to underwater sounds. Conversely, except for deep-diving elephant seals, phocids are quite sensitive to acoustic signals both in air and under water. Finally, despite differences in absolute hearing sensitivity, pinnipeds have similar masked hearing capabilities in both media, supporting the notion that cochlear mechanics determine the effects of noise on hearing.

Experimental Analysis of the Mechanism of Hearing under Water

PubMed Central

Chordekar, Shai; Kishon-Rabin, Liat; Kriksunov, Leonid; Adelman, Cahtia; Sohmer, Haim

2015-01-01

The mechanism of human hearing under water is debated. Some suggest it is by air conduction (AC), others by bone conduction (BC), and others by a combination of AC and BC. A clinical bone vibrator applied to soft tissue sites on the head, neck, and thorax also elicits hearing by a mechanism called soft tissue conduction (STC) or nonosseous BC. The present study was designed to test whether underwater hearing at low intensities is by AC or by osseous BC based on bone vibrations or by nonosseous BC (STC). Thresholds of normal hearing participants to bone vibrator stimulation with their forehead in air were recorded and again when forehead and bone vibrator were under water. A vibrometer detected vibrations of a dry human skull in all similar conditions (in air and under water) but not when water was the intermediary between the sound source and the skull forehead. Therefore, the intensities required to induce vibrations of the dry skull in water were significantly higher than the underwater hearing thresholds of the participants, under conditions when hearing by AC and osseous BC is not likely. The results support the hypothesis that hearing under water at low sound intensities may be attributed to nonosseous BC (STC). PMID:26770975

Sound absorption characteristics of aluminum foam with spherical cells

NASA Astrophysics Data System (ADS)

Li, Yunjie; Wang, Xinfu; Wang, Xingfu; Ren, Yuelu; Han, Fusheng; Wen, Cuie

2011-12-01

Aluminum foams were fabricated by an infiltration process. The foams possess spherical cells with a fixed porosity of 65% and varied pore sizes which ranged from 1.3 to 1.9 mm. The spherical cells are interconnected by small pores or pore openings on the cell walls that cause the foams show a characteristic of open cell structures. The sound absorption coefficient of the aluminum foams was measured by a standing wave tube and calculated by a transfer function method. It is shown that the sound absorption coefficient increases with an increase in the number of pore openings in the unit area or with a decrease of the diameter of the pore openings in the range of 0.3 to 0.4 mm. If backed with an air cavity, the resonant absorption peaks in the sound absorption coefficient versus frequency curves will be shifted toward lower frequencies as the cavity depth is increased. The samples with the same pore opening size but different pore size show almost the same absorption behavior, especially in the low frequency range. The present results are in good agreement with some theoretical predictions based on the acoustic impedance measurements of metal foams with circular apertures and cylindrical cavities and the principle of electroacoustic analogy.

Rainbow-trapping absorbers: Broadband, perfect and asymmetric sound absorption by subwavelength panels for transmission problems.

PubMed

Jiménez, Noé; Romero-García, Vicent; Pagneux, Vincent; Groby, Jean-Philippe

2017-10-19

Perfect, broadband and asymmetric sound absorption is theoretically, numerically and experimentally reported by using subwavelength thickness panels in a transmission problem. The panels are composed of a periodic array of varying crosssection waveguides, each of them being loaded by Helmholtz resonators (HRs) with graded dimensions. The low cut-off frequency of the absorption band is fixed by the resonance frequency of the deepest HR, that reduces drastically the transmission. The preceding HR is designed with a slightly higher resonance frequency with a geometry that allows the impedance matching to the surrounding medium. Therefore, reflection vanishes and the structure is critically coupled. This results in perfect sound absorption at a single frequency. We report perfect absorption at 300 Hz for a structure whose thickness is 40 times smaller than the wavelength. Moreover, this process is repeated by adding HRs to the waveguide, each of them with a higher resonance frequency than the preceding one. Using this frequency cascade effect, we report quasi-perfect sound absorption over almost two frequency octaves ranging from 300 to 1000 Hz for a panel composed of 9 resonators with a total thickness of 11 cm, i.e., 10 times smaller than the wavelength at 300 Hz.

Optimization of low frequency sound absorption by cell size control and multiscale poroacoustics modeling

NASA Astrophysics Data System (ADS)

Park, Ju Hyuk; Yang, Sei Hyun; Lee, Hyeong Rae; Yu, Cheng Bin; Pak, Seong Yeol; Oh, Chi Sung; Kang, Yeon June; Youn, Jae Ryoun

2017-06-01

Sound absorption of a polyurethane (PU) foam was predicted for various geometries to fabricate the optimum microstructure of a sound absorbing foam. Multiscale numerical analysis for sound absorption was carried out by solving flow problems in representative unit cell (RUC) and the pressure acoustics equation using Johnson-Champoux-Allard (JCA) model. From the numerical analysis, theoretical optimum cell diameter for low frequency sound absorption was evaluated in the vicinity of 400 μm under the condition of 2 cm-80 K (thickness of 2 cm and density of 80 kg/m3) foam. An ultrasonic foaming method was employed to modulate microcellular structure of PU foam. Mechanical activation was only employed to manipulate the internal structure of PU foam without any other treatment. A mean cell diameter of PU foam was gradually decreased with increase in the amplitude of ultrasonic waves. It was empirically found that the reduction of mean cell diameter induced by the ultrasonic wave enhances acoustic damping efficiency in low frequency ranges. Moreover, further analyses were performed with several acoustic evaluation factors; root mean square (RMS) values, noise reduction coefficients (NRC), and 1/3 octave band spectrograms.

Ultrathin multi-slit metamaterial as excellent sound absorber: Influence of micro-structure

NASA Astrophysics Data System (ADS)

Ren, S. W.; Meng, H.; Xin, F. X.; Lu, T. J.

2016-01-01

An ultrathin (subwavelength) hierarchy multi-slit metamaterial with simultaneous negative effective density and negative compressibility is proposed to absorb sound over a wide frequency range. Different from conventional acoustic metamaterials having only negative real parts of acoustic parameters, the imaginary parts of effective density and compressibility are both negative for the proposed metamaterial, which result in superior viscous and thermal dissipation of sound energy. By combining the slit theory of sound absorption with the double porosity theory for porous media, a theoretical model is developed to investigate the sound absorption performance of the metamaterial. To verify the model, a finite element model is established to calculate the effective density, compressibility, and sound absorption of the metamaterial. It is theoretically and numerically confirmed that, upon introducing micro-slits into the meso-slits matrix, the multi-slit metamaterial possesses indeed negative imaginary parts of effective density and compressibility. The influence of micro-slits on the acoustical performance of the metamaterial is analyzed in the context of its specific surface area and static flow resistivity. This work shows great potential of multi-slit metamaterials in noise control applications that require both small volume and small weight of sound-absorbing materials.

The influence of sea ice, wind speed and marine mammals on Southern Ocean ambient sound

PubMed Central

van Opzeeland, Ilse; Boebel, Olaf

2017-01-01

This paper describes the natural variability of ambient sound in the Southern Ocean, an acoustically pristine marine mammal habitat. Over a 3-year period, two autonomous recorders were moored along the Greenwich meridian to collect underwater passive acoustic data. Ambient sound levels were strongly affected by the annual variation of the sea-ice cover, which decouples local wind speed and sound levels during austral winter. With increasing sea-ice concentration, area and thickness, sound levels decreased while the contribution of distant sources increased. Marine mammal sounds formed a substantial part of the overall acoustic environment, comprising calls produced by Antarctic blue whales (Balaenoptera musculus intermedia), fin whales (Balaenoptera physalus), Antarctic minke whales (Balaenoptera bonaerensis) and leopard seals (Hydrurga leptonyx). The combined sound energy of a group or population vocalizing during extended periods contributed species-specific peaks to the ambient sound spectra. The temporal and spatial variation in the contribution of marine mammals to ambient sound suggests annual patterns in migration and behaviour. The Antarctic blue and fin whale contributions were loudest in austral autumn, whereas the Antarctic minke whale contribution was loudest during austral winter and repeatedly showed a diel pattern that coincided with the diel vertical migration of zooplankton. PMID:28280544

Theoretical analysis of the sound absorption characteristics of periodically stiffened micro-perforated plates

NASA Astrophysics Data System (ADS)

Zhou, Hai-An; Wang, Xiao-Ming; Mei, Yu-Lin

2014-10-01

The vibro-acoustic responses and sound absorption characteristics of two kinds of periodically stiffened micro-perforated plates are analyzed theoretically. The connected periodical structures of the stiffened plates can be ribs or block-like structures. Based on fundamental acoustic formulas of the micro-perforated plate of Maa and Takahashi, semi-analytical models of the vibrating stiffened plates are developed in this paper. Approaches like the space harmonicmethod, Fourier transforms and finite elementmethod (FEM) are adopted to investigate both kinds of the stiffened plates. In the present work, the vibro-acoustic responses of micro-perforated stiffened plates in the wavenumber space are expressed as functions of plate displacement amplitudes. After approximate numerical solutions of the amplitudes, the vibration equations and sound absorption coefficients of the two kinds of stiffened plates in the physical space are then derived by employing the Fourier inverse transform. In numerical examples, the effects of some physical parameters, such as the perforation ratio, incident angles and periodical distances etc., on the sound absorption performance are examined. The proposed approaches are also validated by comparing the present results with solutions of Takahashi and previous studies of stiffened plates. Numerical results indicate that the flexural vibration of the plate has a significant effect on the sound absorption coefficient in the water but has little influence in the air.

Sound absorption by subwavelength membrane structures: A geometric perspective

NASA Astrophysics Data System (ADS)

Yang, Min; Li, Yong; Meng, Chong; Fu, Caixing; Mei, Jun; Yang, Zhiyu; Sheng, Ping

2015-12-01

Decorated membranes comprising a thin layer of elastic film with small rigid platelets fixed on top have been found to be efficient absorbers of low-frequency sound. In this work we consider the problem of sound absorption from a perspective aimed at deriving upper bounds under different scenarios, i.e., whether the sound is incident from one side only or from both sides, and whether there is a reflecting surface on the back side of the membrane. By considering the negligible thickness of the membrane, usually on the order of a fraction of one millimeter, we derive a relation showing that the sum of the incoming sound waves' (complex) pressure amplitudes, averaged over the area of the membrane, must be equal to that of the outgoing waves. By using this relation, and without going to any details of the wave solutions, it is shown that the maximum absorption achievable from one-sided incidence is 50%, while the maximum absorption with a back-reflecting surface can reach 100%. The latter was attained by the hybridized resonances. All the results are shown to be in excellent agreement with the experiments. This generalized perspective, when used together with the Green function's formalism, can be useful in gaining insights into the constraints on what are achievable in scatterings and absorption by thin film structures and delineating them.

Study of physical and sound absorbing property of epoxy blended coir dust biocomposite

NASA Astrophysics Data System (ADS)

Nath, G.; Mishra, S. P.

2016-09-01

Reinforcement biocomposite has gained more attention recently due to its low cost, abundantly availability, low density, specific properties, easy method of separation, enhanced energy recovery, CO2 neutrality, biodegradability and recyclable in nature. As a waste product of coconut fruit, the coconut coir dust (CCD) obtained from the coconut husk. The biocomposite material prepared from the CCD modified with the proper blended solution with the help of ultrasonic technique. The study of adiabatic compressibility of acetone / water (70/30) worth its blending property for bleaching of CCD. The biocomposite material of CCD was prepared with epoxy resin. The different physical properties such as sound absorption coefficient, thermal conductivity and electrical conductivity were measured. The morphological study of biocomposite and measurement of sound absorption coefficient shows good evidence of sound absorbing characteristics of biocomposite of CCD. The sound absorption property of composite material shows a significant result where as the thermal conductivity and electrical conductivity executes a weak result. Thus biocomposite of CCD can acts as a good sound absorber and band conductor of heat and electric current.

Sound transmission through a microperforated-panel structure with subdivided air cavities.

PubMed

Toyoda, Masahiro; Takahashi, Daiji

2008-12-01

The absorption characteristics of a microperforated-panel (MPP) absorber have been widely investigated, and MPPs are recognized as a next-generation absorbing material due to their fiber-free nature and attractive appearance. Herein, further possibilities of MPPs are investigated theoretically from a sound transmission viewpoint. Employing an analytical model composed of a typical MPP and a back wall with an infinite extent, transmission loss through the structure is obtained. Although MPP structures generally have great potential for sound absorption, an improvement in the transmission loss at midfrequencies, which is important for architectural sound insulation, is not sufficient when using a backing cavity alone. Hence, to improve transmission loss at midfrequencies, an air-cavity-subdivision technique is applied to MPP structures. By subdividing the air cavity with partitions, each cell can create a local one-dimensional sound field as well as lead to a normal incidence into the apertures, which is the most effective condition for Helmholtz-type resonance absorption. Moreover, by providing the same motion as the back wall to the MPP, the sound-insulation performance can be further improved at midfrequencies.

Resonant behaviour of MHD waves on magnetic flux tubes. I - Connection formulae at the resonant surfaces. II - Absorption of sound waves by sunspots

NASA Technical Reports Server (NTRS)

Sakurai, Takashi; Goossens, Marcel; Hollweg, Joseph V.

1991-01-01

The present method of addressing the resonance problems that emerge in such MHD phenomena as the resonant absorption of waves at the Alfven resonance point avoids solving the fourth-order differential equation of dissipative MHD by recourse to connection formulae across the dissipation layer. In the second part of this investigation, the absorption of solar 5-min oscillations by sunspots is interpreted as the resonant absorption of sounds by a magnetic cylinder. The absorption coefficient is interpreted (1) analytically, under certain simplifying assumptions, and numerically, under more general conditions. The observed absorption coefficient magnitude is explained over suitable parameter ranges.

Ultra-thin metamaterial for perfect and quasi-omnidirectional sound absorption

NASA Astrophysics Data System (ADS)

Jiménez, N.; Huang, W.; Romero-García, V.; Pagneux, V.; Groby, J.-P.

2016-09-01

Using the concepts of slow sound and critical coupling, an ultra-thin acoustic metamaterial panel for perfect and quasi-omnidirectional absorption is theoretically and experimentally conceived in this work. The system is made of a rigid panel with a periodic distribution of thin closed slits, the upper wall of which is loaded by Helmholtz Resonators (HRs). The presence of resonators produces a slow sound propagation shifting the resonance frequency of the slit to the deep sub-wavelength regime ( λ/88 ). By controlling the geometry of the slit and the HRs, the intrinsic visco-thermal losses can be tuned in order to exactly compensate the energy leakage of the system and fulfill the critical coupling condition to create the perfect absorption of sound in a large range of incidence angles due to the deep subwavelength behavior.

The absorption of sound by perforated linings

NASA Astrophysics Data System (ADS)

Hughes, I. J.; Dowling, A. P.

1990-09-01

This paper describes a practical application for sound-absorbent perforated screen with a bias flow through the screen. It is postulated that, if a perforated liner with a bias flow of cooling air through the liner is inserted in the afterburner section of a jet engine, all the incident sound may be absorbed at a particular frequency. Experimental results are presented on the absorptive properties of plane liners with circular apertures, showing an agreement with the theoretical model.

Measurement and testing of the acoustic properties of materials: a review

NASA Astrophysics Data System (ADS)

Zeqiri, Bajram; Scholl, Werner; Robinson, Stephen P.

2010-04-01

A review is presented of methods of measurement for a range of key acoustic properties of materials, spanning three application areas: airborne sound, underwater acoustics and ultrasound. The acoustic properties considered, primarily transmission loss (damping) and echo-reduction, are specifically important to the end application of any material. The state-of-the-art in measurement and likely future challenges are described in detail.

37. Photograph of plan for repairs to computer room, 1958, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. Photograph of plan for repairs to computer room, 1958, prepared by the Public Works Office, Underwater Sound Laboratory. Drawing on file at Caretaker Site Office, Naval Undersea Warfare Center, New London. Copyright-free. - Naval Undersea Warfare Center, Bowditch Hall, 600 feet east of Smith Street & 350 feet south of Columbia Cove, West bank of Thames River, New London, New London County, CT

Improvement of acoustical characteristics : wideband bamboo based polymer composite

NASA Astrophysics Data System (ADS)

Farid, M.; Purniawan, A.; Rasyida, A.; Ramadhani, M.; Komariyah, S.

2017-07-01

Environmental friendly and comfortable materials are desirable for applications in the automobile interior. The objective of this research was to examine and develop bamboo based polymer composites applied to the sound absorption materials of automobile door panels. Morphological analysis of the polyurethane/bamboo powder composite materials was carried out using scanning electron microscope to reveal the microscopic material behavior and followed by the FTIR and TGA testing. The finding demonstrated that this acoustical polymer composite materials provided a potential wideband sound absorption material. The range of frequency can be controlled between 500 and 4000 Hz with an average of sound absorption coefficient around 0.411 and it met to the door panels criteria.

Experimental and Theoretical Analysis of Sound Absorption Properties of Finely Perforated Wooden Panels.

PubMed

Song, Boqi; Peng, Limin; Fu, Feng; Liu, Meihong; Zhang, Houjiang

2016-11-22

Perforated wooden panels are typically utilized as a resonant sound absorbing material in indoor noise control. In this paper, the absorption properties of wooden panels perforated with tiny holes of 1-3 mm diameter were studied both experimentally and theoretically. The Maa-MPP (micro perforated panels) model and the Maa-Flex model were applied to predict the absorption regularities of finely perforated wooden panels. A relative impedance comparison and full-factorial experiments were carried out to verify the feasibility of the theoretical models. The results showed that the Maa-Flex model obtained good agreement with measured results. Control experiments and measurements of dynamic mechanical properties were carried out to investigate the influence of the wood characteristics. In this study, absorption properties were enhanced by sound-induced vibration. The relationship between the dynamic mechanical properties and the panel mass-spring vibration absorption was revealed. While the absorption effects of wood porous structure were not found, they were demonstrated theoretically by using acoustic wave propagation in a simplified circular pipe with a suddenly changed cross-section model. This work provides experimental and theoretical guidance for perforation parameter design.

A sound budget for the southeastern Bering Sea: measuring wind, rainfall, shipping, and other sources of underwater sound.

PubMed

Nystuen, Jeffrey A; Moore, Sue E; Stabeno, Phyllis J

2010-07-01

Ambient sound in the ocean contains quantifiable information about the marine environment. A passive aquatic listener (PAL) was deployed at a long-term mooring site in the southeastern Bering Sea from 27 April through 28 September 2004. This was a chain mooring with lots of clanking. However, the sampling strategy of the PAL filtered through this noise and allowed the background sound field to be quantified for natural signals. Distinctive signals include the sound from wind, drizzle and rain. These sources dominate the sound budget and their intensity can be used to quantify wind speed and rainfall rate. The wind speed measurement has an accuracy of +/-0.4 m s(-1) when compared to a buoy-mounted anemometer. The rainfall rate measurement is consistent with a land-based measurement in the Aleutian chain at Cold Bay, AK (170 km south of the mooring location). Other identifiable sounds include ships and short transient tones. The PAL was designed to reject transients in the range important for quantification of wind speed and rainfall, but serendipitously recorded peaks in the sound spectrum between 200 Hz and 3 kHz. Some of these tones are consistent with whale calls, but most are apparently associated with mooring self-noise.

Development of simplified procedure for computing the absorption of sound by the atmosphere and applicability to aircraft noise certification : proposed SAE method

DOT National Transportation Integrated Search

2012-11-30

This report presents the results of the study to extend the useful attenuation range of the Approximate Method outlined in the American National Standard, Method for Calculation of the Absorption of Sound by the Atmosphere (ANSI S1.26-1995), an...

Sound absorption by a Helmholtz resonator

NASA Astrophysics Data System (ADS)

Komkin, A. I.; Mironov, M. A.; Bykov, A. I.

2017-07-01

Absorption characteristics of a Helmholtz resonator positioned at the end wall of a circular duct are considered. The absorption coefficient of the resonator is experimentally investigated as a function of the diameter and length of the resonator neck and the depth of the resonator cavity. Based on experimental data, the linear analytic model of a Helmholtz resonator is verified, and the results of verification are used to determine the dissipative attached length of the resonator neck so as to provide the agreement between experimental and calculated data. Dependences of sound absorption by a Helmholtz resonator on its geometric parameters are obtained.

An Autonomous Underwater Recorder Based on a Single Board Computer

PubMed Central

Caldas-Morgan, Manuel; Alvarez-Rosario, Alexander; Rodrigues Padovese, Linilson

2015-01-01

As industrial activities continue to grow on the Brazilian coast, underwater sound measurements are becoming of great scientific importance as they are essential to evaluate the impact of these activities on local ecosystems. In this context, the use of commercial underwater recorders is not always the most feasible alternative, due to their high cost and lack of flexibility. Design and construction of more affordable alternatives from scratch can become complex because it requires profound knowledge in areas such as electronics and low-level programming. With the aim of providing a solution; a well succeeded model of a highly flexible, low-cost alternative to commercial recorders was built based on a Raspberry Pi single board computer. A properly working prototype was assembled and it demonstrated adequate performance levels in all tested situations. The prototype was equipped with a power management module which was thoroughly evaluated. It is estimated that it will allow for great battery savings on long-term scheduled recordings. The underwater recording device was successfully deployed at selected locations along the Brazilian coast, where it adequately recorded animal and manmade acoustic events, among others. Although power consumption may not be as efficient as that of commercial and/or micro-processed solutions, the advantage offered by the proposed device is its high customizability, lower development time and inherently, its cost. PMID:26076479

Noise reduction by the application of an air-bubble curtain in offshore pile driving

NASA Astrophysics Data System (ADS)

Tsouvalas, A.; Metrikine, A. V.

2016-06-01

Underwater noise pollution is a by-product of marine industrial operations. In particular, the noise generated when a foundation pile is driven into the soil with an impact hammer is considered to be harmful for the aquatic species. In an attempt to reduce the ecological footprint, several noise mitigation techniques have been investigated. Among the various solutions proposed, the air-bubble curtain is often applied due to its efficacy in noise reduction. In this paper, a model is proposed for the investigation of the sound reduction during marine piling when an air-bubble curtain is placed around the pile. The model consists of the pile, the surrounding water and soil media, and the air-bubble curtain which is positioned at a certain distance from the pile surface. The solution approach is semi-analytical and is based on the dynamic sub-structuring technique and the modal decomposition method. Two main results of the paper can be distinguished. First, a new model is proposed that can be used for predictions of the noise levels in a computationally efficient manner. Second, an analysis is presented of the principal mechanisms that are responsible for the noise reduction due to the application of the air-bubble curtain in marine piling. The understanding of these mechanisms turns to be crucial for the exploitation of the maximum efficiency of the system. It is shown that the principal mechanism of noise reduction depends strongly on the frequency content of the radiated sound and the characteristics of the bubbly medium. For piles of large diameter which radiate most of the acoustic energy at relatively low frequencies, the noise reduction is mainly attributed to the mismatch of the acoustic impedances between the seawater and the bubbly layer. On the contrary, for smaller piles and when the radiated acoustic energy is concentrated at frequencies close to, or higher than, the resonance frequency of the air bubbles, the sound absorption within the bubbly layer becomes critical.

Exposure and materiality of the secondary room and its impact on the impulse response of coupled-volume concert halls

NASA Astrophysics Data System (ADS)

Ermann, Michael; Johnson, Marty

2005-06-01

How does sound decay when one room is partially exposed to another (acoustically coupled)? More specifically, this research aims to quantify how operational and design decisions impact sound fields in the design of concert halls with acoustical coupling. By adding a second room to a concert hall, and designing doors to control the sonic transparency between the two rooms, designers can create a new, coupled acoustic. Concert halls use coupling to achieve a variable, longer, and distinct reverberant quality for their musicians and listeners. For this study a coupled-volume shoebox concert hall is conceived with a fixed geometric volume, form, and primary-room sound absorption. Aperture size and secondary-room sound absorption levels are established as variables. Statistical analysis of sound decay in this simulated hall suggests a highly sensitive relationship between the double-sloped condition and (1) architectural composition, as defined by the aperture size exposing the chamber and (2) materiality, as defined by the sound absorptance in the coupled volume. The theoretical, mathematical predictions are compared with coupled-volume concert hall field measurements and guidelines are suggested for future designs of coupled-volume concert halls.

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Rice, Edward J.; Groesbeck, Donald E.

1987-01-01

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the dirction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Rice, Edward J.; Groesbeck, Donald E.

1990-01-01

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the direction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Analysis of sound absorption performance of an electroacoustic absorber using a vented enclosure

NASA Astrophysics Data System (ADS)

Cho, Youngeun; Wang, Semyung; Hyun, Jaeyub; Oh, Seungjae; Goo, Seongyeol

2018-03-01

The sound absorption performance of an electroacoustic absorber (EA) is primarily influenced by the dynamic characteristics of the loudspeaker that acts as the actuator of the EA system. Therefore, the sound absorption performance of the EA is maximum at the resonance frequency of the loudspeaker and tends to degrade in the low-frequency and high-frequency bands based on this resonance frequency. In this study, to adjust the sound absorption performance of the EA system in the low-frequency band of approximately 20-80 Hz, an EA system using a vented enclosure that has previously been used to enhance the radiating sound pressure of a loudspeaker in the low-frequency band, is proposed. To verify the usefulness of the proposed system, two acoustic environments are considered. In the first acoustic environment, the vent of the vented enclosure is connected to an external sound field that is distinct from the sound field coupled to the EA. In this case, the acoustic effect of the vented enclosure on the performance of the EA is analyzed through an analytical approach using dynamic equations and an impedance-based equivalent circuit. Then, it is verified through numerical and experimental approaches. Next, in the second acoustic environment, the vent is connected to the same external sound field as the EA. In this case, the effect of the vented enclosure on the EA is investigated through an analytical approach and finally verified through a numerical approach. As a result, it is confirmed that the characteristics of the sound absorption performances of the proposed EA system using the vented enclosure in the two acoustic environments considered in this study are different from each other in the low-frequency band of approximately 20-80 Hz. Furthermore, several case studies on the change tendency of the performance of the EA using the vented enclosure according to the critical design factors or vent number for the vented enclosure are also investigated. In the future, even if the proposed EA system using a vented enclosure is extended to a large number of arrays required for 3D sound field control, it is expected to be an attractive solution that can contribute to an improvement in low-frequency noise reduction without causing economic and system complexity problems.

Assessing sound exposure from shipping in coastal waters using a single hydrophone and Automatic Identification System (AIS) data.

PubMed

Merchant, Nathan D; Witt, Matthew J; Blondel, Philippe; Godley, Brendan J; Smith, George H

2012-07-01

Underwater noise from shipping is a growing presence throughout the world's oceans, and may be subjecting marine fauna to chronic noise exposure with potentially severe long-term consequences. The coincidence of dense shipping activity and sensitive marine ecosystems in coastal environments is of particular concern, and noise assessment methodologies which describe the high temporal variability of sound exposure in these areas are needed. We present a method of characterising sound exposure from shipping using continuous passive acoustic monitoring combined with Automatic Identification System (AIS) shipping data. The method is applied to data recorded in Falmouth Bay, UK. Absolute and relative levels of intermittent ship noise contributions to the 24-h sound exposure level are determined using an adaptive threshold, and the spatial distribution of potential ship sources is then analysed using AIS data. This technique can be used to prioritize shipping noise mitigation strategies in coastal marine environments. Copyright © 2012 Elsevier Ltd. All rights reserved.

Acoustic habitat of an oceanic archipelago in the Southwestern Atlantic

NASA Astrophysics Data System (ADS)

Bittencourt, Lis; Barbosa, Mariana; Secchi, Eduardo; Lailson-Brito, José; Azevedo, Alexandre

2016-09-01

Underwater soundscapes can be highly variable, and in natural conditions are often dominated by biological signals and physical features of the environment. Few studies, however, focused on oceanic islands soundscapes. Islands in the middle of ocean basins can provide a good example of how untouched marine soundscapes are. Autonomous acoustic recordings were carried out in two different seasons in Trindade-Martin Vaz Archipelago, Southwestern Atlantic, providing nearly continuous data for both periods. Sound levels varied daily and between seasons. During summer, higher frequencies were noisier than lower frequencies, with snapping shrimp being the dominating sound source. During winter, lower frequencies were noisier than higher frequencies due to humpback whale constant singing. Biological signal detection had a marked temporal pattern, playing an important role in the soundscape. Over 1000 humpback whale sounds were detected hourly during winter. Fish vocalizations were detected mostly during night time during both summer and winter. The results show an acoustic habitat dominated by biological sound sources and highlight the importance of the island to humpback whales in winter.

Experimental Evaluation of Tuned Chamber Core Panels for Payload Fairing Noise Control

NASA Technical Reports Server (NTRS)

Schiller, Noah H.; Allen, Albert R.; Herlan, Jonathan W.; Rosenthal, Bruce N.

2015-01-01

Analytical models have been developed to predict the sound absorption and sound transmission loss of tuned chamber core panels. The panels are constructed of two facesheets sandwiching a corrugated core. When ports are introduced through one facesheet, the long chambers within the core can be used as an array of low-frequency acoustic resonators. To evaluate the accuracy of the analytical models, absorption and sound transmission loss tests were performed on flat panels. Measurements show that the acoustic resonators embedded in the panels improve both the absorption and transmission loss of the sandwich structure at frequencies near the natural frequency of the resonators. Analytical predictions for absorption closely match measured data. However, transmission loss predictions miss important features observed in the measurements. This suggests that higher-fidelity analytical or numerical models will be needed to supplement transmission loss predictions in the future.

Design, characterization and modeling of biobased acoustic foams

NASA Astrophysics Data System (ADS)

Ghaffari Mosanenzadeh, Shahrzad

Polymeric open cell foams are widely used as sound absorbers in sectors such as automobile, aerospace, transportation and building industries, yet there is a need to improve sound absorption of these foams through understanding the relation between cell morphology and acoustic properties of porous material. Due to complicated microscopic structure of open cell foams, investigating the relation between foam morphology and acoustic properties is rather intricate and still an open problem in the field. The focus of this research is to design and develop biobased open cell foams for acoustic applications to replace conventional petrochemical based foams as well as investigating the link between cell morphology and macroscopic properties of open cell porous structures. To achieve these objectives, two industrially produced biomaterials, polylactide (PLA) and polyhydroxyalkanoate (PHA) and their composites were examined and highly porous biobased foams were fabricated by particulate leaching and compression molding. Acoustic absorption capability of these foams was enhanced utilizing the effect of co-continuous blends to form a bimodal porous structure. To tailor mechanical and acoustic properties of biobased foams, blends of PLA and PHA were studied to reach the desired mechanical and viscoelastic properties. To enhance acoustic properties of porous medium for having a broad band absorption effect, cell structure must be appropriately graded. Such porous structures with microstructural gradation are called Functionally Graded Materials (FGM). A novel graded foam structure was designed with superior sound absorption to demonstrate the effect of cell arrangement on performance of acoustic fixtures. Acoustic measurements were performed in a two microphone impedance tube and acoustic theory of Johnson-Champoux-Allard was applied to the fabricated foams to determine micro cellular properties such as tortuosity, viscous and thermal lengths from sound absorption impedance tube measurements using an inverse technique. As the next step towards in depth understanding of the relation between cell morphology and sound absorption of open cell foams, a semi-analytical model was developed to account for the effect of micro cellular properties such as cell wall thickness and reticulation rate on overall macroscopic and structural properties. Developed model provides the tools to optimize the porous structure and enhance sound absorption capability.

Measurement of the absorption coefficient using the sound-intensity technique

NASA Technical Reports Server (NTRS)

Atwal, M.; Bernhard, R.

1984-01-01

The possibility of using the sound intensity technique to measure the absorption coefficient of a material is investigated. This technique measures the absorption coefficient by measuring the intensity incident on the sample and the net intensity reflected by the sample. Results obtained by this technique are compared with the standard techniques of measuring the change in the reverberation time and the standing wave ratio in a tube, thereby, calculating the random incident and the normal incident adsorption coefficient.

Impacts of distinct observations during the 2009 Prince William Sound field experiment: A data assimilation study

NASA Astrophysics Data System (ADS)

Li, Zhijin; Chao, Yi; Farrara, John D.; McWilliams, James C.

2013-07-01

A set of data assimilation experiments, known as Observing System Experiments (OSEs) are performed to assess the relative impacts of different types of observations acquired during the 2009 Prince William Sound Field Experiment. The observations assimilated consist primarily of two types: High Frequency (HF) radar surface velocities and vertical profiles of temperature/salinity (T/S) measured by ships, moorings, an Autonomous Underwater Vehicle and a glider. The impact of all the observations, HF radar surface velocities, and T/S profiles is assessed. Without data assimilation, a frequently occurring cyclonic eddy in the central Sound is overly persistent and intense. The assimilation of the HF radar velocities effectively reduces these biases and improves the representation of the velocities as well as the T/S fields in the Sound. The assimilation of the T/S profiles improves the large scale representation of the temperature/salinity and also the velocity field in the central Sound. The combination of the HF radar surface velocities and sparse T/S profiles results in an observing system capable of representing the circulation in the Sound reliably and thus producing analyses and forecasts with useful skill.

Joint inversion for transponder localization and sound-speed profile temporal variation in high-precision acoustic surveys.

PubMed

Li, Zhao; Dosso, Stan E; Sun, Dajun

2016-07-01

This letter develops a Bayesian inversion for localizing underwater acoustic transponders using a surface ship which compensates for sound-speed profile (SSP) temporal variation during the survey. The method is based on dividing observed acoustic travel-time data into time segments and including depth-independent SSP variations for each segment as additional unknown parameters to approximate the SSP temporal variation. SSP variations are estimated jointly with transponder locations, rather than calculated separately as in existing two-step inversions. Simulation and sea-trial results show this localization/SSP joint inversion performs better than two-step inversion in terms of localization accuracy, agreement with measured SSP variations, and computational efficiency.

Cumulative Effects of Human Activities on Marine Mammal Populations

DTIC Science & Technology

2015-09-30

marine mammals and sea turtles. She has studied habitat use of whales and dolphins, underwater sound levels and environmental impacts of offshore wind ... turbines on marine mammals, and migration pathways and hot spots of marine predators at the National Oceanic and Atmospheric Administration as part...distribution of wild animal and plant populations, and the use of computer-intensive methods to fit and compare stochastic models of wildlife population

Underwater Sound Radiation from Large Raindrops

DTIC Science & Technology

1991-09-01

decreasing shape of the impact spectrum, one must pick a reference point rather that a peak value to compare one drop with another. For comparison of...34 1. Type I Bubble Spectral Density and Peak Pressure ............... 34 2. Type II Bubble Average Spectral Densities at 1 m on Axis (20 C...32 Table 4. TYPE II BUBBLE AVERAGE PEAK SPECTRAL DENSITY SU M M A RY ............................................. 39 Table 5. SUMMARY

Sound Propagation around Underwater Seamounts

DTIC Science & Technology

2009-02-01

Algorithm 177 C.1 Processing Real World Data .................. ........ 178 C.2 Method for Finding Zero -crossings ................... .... 179 C.3 Handling...BASSEX experiment (figure is from Hyun Joe Kim, M IT, PhD Thesis) ................... .. .......... 25 2-2 Time front generated using the Range...30 2-4 Pressure level, given in dB re 1lPa, inside the forward-scattered field of the Kermit-Roosevelt Seamount. Results are generated using the RAM

Contributions to Automated Realtime Underwater Navigation

DTIC Science & Technology

2012-02-01

help by scrubbing circuits–Scotty McCue was always there to help, and demonstrate proper circuit scrubbing technique. Carl Kaiser has been great at... Jung Lee, and of course, my committee again. My friends and fellow JP students have provided advice on code or prose, sounding boards for crazy ideas...order): Chris Murphy, Clay Kunz, Jeff Kaeli, Mark van Middlesworth, Peter Kimball, Wu- Jung Lee, Heather Beem, Derya Akkaynak Yellin, Kalina

The Effects of Sand Sediment Volume Heterogeneities on Sound Propagation and Scattering

DTIC Science & Technology

2011-09-01

previously developed at APL- UW for the study of high-frequency acoustics . These models include perturbation models applied to scattering from the...shell shapes (Figure 1). The acoustic modeling to this point has utilized Ivakin’s unified approach to volume and roughness scattering [3...sediments: A modeling approach and application to a shelly sand-mud environment,” in the Proceeding of the European Conference on Underwater Acoustics

A method for approximating acoustic-field-amplitude uncertainty caused by environmental uncertainties.

PubMed

James, Kevin R; Dowling, David R

2008-09-01

In underwater acoustics, the accuracy of computational field predictions is commonly limited by uncertainty in environmental parameters. An approximate technique for determining the probability density function (PDF) of computed field amplitude, A, from known environmental uncertainties is presented here. The technique can be applied to several, N, uncertain parameters simultaneously, requires N+1 field calculations, and can be used with any acoustic field model. The technique implicitly assumes independent input parameters and is based on finding the optimum spatial shift between field calculations completed at two different values of each uncertain parameter. This shift information is used to convert uncertain-environmental-parameter distributions into PDF(A). The technique's accuracy is good when the shifted fields match well. Its accuracy is evaluated in range-independent underwater sound channels via an L(1) error-norm defined between approximate and numerically converged results for PDF(A). In 50-m- and 100-m-deep sound channels with 0.5% uncertainty in depth (N=1) at frequencies between 100 and 800 Hz, and for ranges from 1 to 8 km, 95% of the approximate field-amplitude distributions generated L(1) values less than 0.52 using only two field calculations. Obtaining comparable accuracy from traditional methods requires of order 10 field calculations and up to 10(N) when N>1.

Numerical analysis of flow induced noise propagation in supercavitating vehicles at subsonic speeds.

PubMed

Ramesh, Sai Sudha; Lim, Kian Meng; Zheng, Jianguo; Khoo, Boo Cheong

2014-04-01

Flow supercavitation begins when fluid is accelerated over a sharp edge, usually at the nose of an underwater vehicle, where phase change occurs and causes low density gaseous cavity to gradually envelop the whole object (supercavity) and thereby enabling higher speeds of underwater vehicles. The process of supercavity inception/development by means of "natural cavitation" and its sustainment through ventilated cavitation result in turbulence and fluctuations at the water-vapor interface that manifest themselves as major sources of hydrodynamic noise. Therefore in the present context, three main sources are investigated, namely, (1) flow generated noise due to turbulent pressure fluctuations around the supercavity, (2) small scale pressure fluctuations at the vapor-water interface, and (3) pressure fluctuations due to direct impingement of ventilated gas-jets on the supercavity wall. An understanding of their relative contributions toward self-noise is very crucial for the efficient operation of high frequency acoustic sensors that facilitate the vehicle's guidance system. Qualitative comparisons of acoustic pressure distribution resulting from aforementioned sound sources are presented by employing a recently developed boundary integral method. By using flow data from a specially developed unsteady computational fluid dynamics solver for simulating supercavitating flows, the boundary-element method based acoustic solver was developed for computing flow generated sound.

Estimation of Antarctic Land-Fast Sea Ice Algal Biomass and Snow Thickness From Under-Ice Radiance Spectra in Two Contrasting Areas

NASA Astrophysics Data System (ADS)

Wongpan, P.; Meiners, K. M.; Langhorne, P. J.; Heil, P.; Smith, I. J.; Leonard, G. H.; Massom, R. A.; Clementson, L. A.; Haskell, T. G.

2018-03-01

Fast ice is an important component of Antarctic coastal marine ecosystems, providing a prolific habitat for ice algal communities. This work examines the relationships between normalized difference indices (NDI) calculated from under-ice radiance measurements and sea ice algal biomass and snow thickness for Antarctic fast ice. While this technique has been calibrated to assess biomass in Arctic fast ice and pack ice, as well as Antarctic pack ice, relationships are currently lacking for Antarctic fast ice characterized by bottom ice algae communities with high algal biomass. We analyze measurements along transects at two contrasting Antarctic fast ice sites in terms of platelet ice presence: near and distant from an ice shelf, i.e., in McMurdo Sound and off Davis Station, respectively. Snow and ice thickness, and ice salinity and temperature measurements support our paired in situ optical and biological measurements. Analyses show that NDI wavelength pairs near the first chlorophyll a (chl a) absorption peak (≈440 nm) explain up to 70% of the total variability in algal biomass. Eighty-eight percent of snow thickness variability is explained using an NDI with a wavelength pair of 648 and 567 nm. Accounting for pigment packaging effects by including the ratio of chl a-specific absorption coefficients improved the NDI-based algal biomass estimation only slightly. Our new observation-based algorithms can be used to estimate Antarctic fast ice algal biomass and snow thickness noninvasively, for example, by using moored sensors (time series) or mapping their spatial distributions using underwater vehicles.

Opo lidar sounding of trace atmospheric gases in the 3 - 4 μm spectral range

NASA Astrophysics Data System (ADS)

Romanovskii, Oleg A.; Sadovnikov, Sergey A.; Kharchenko, Olga V.; Yakovlev, Semen V.

2018-04-01

The applicability of a KTA crystal-based laser system with optical parametric oscillators (OPO) generation to lidar sounding of the atmosphere in the spectral range 3-4 μm is studied in this work. A technique developed for lidar sounding of trace atmospheric gases (TAG) is based on differential absorption lidar (DIAL) method and differential optical absorption spectroscopy (DOAS). The DIAL-DOAS technique is tested to estimate its efficiency for lidar sounding of atmospheric trace gases. The numerical simulation performed shows that a KTA-based OPO laser is a promising source of radiation for remote DIAL-DOAS sounding of the TAGs under study along surface tropospheric paths. A possibility of using a PD38-03-PR photodiode for the DIAL gas analysis of the atmosphere is shown.

A theoretical study on the impact of particle scattering on the channel characteristics of underwater optical communication system

NASA Astrophysics Data System (ADS)

Sahu, Sanjay Kumar; Shanmugam, Palanisamy

2018-02-01

Scattering by water molecules and particulate matters determines the path and distance of photon propagation in underwater medium. Consequently, photon angle of scattering (given by scattering phase function) requires to be considered in addition to the extinction coefficient of the aquatic medium governed by the absorption and scattering coefficients in channel characterization for an underwater wireless optical communication (UWOC) system. This study focuses on analyzing the received signal power and impulse response of UWOC channel based on Monte-Carlo simulations for different water types, link distances, link geometries and transceiver parameters. A newly developed scattering phase function (referred to as SS phase function), which represents the real water types more accurately like the Petzold phase function, is considered for quantification of the channel characteristics along with the effects of absorption and scattering coefficients. A comparison between the results simulated using various phase function models and the experimental measurements of Petzold revealed that the SS phase function model predicts values closely matching with the actual values of the Petzold's phase function, which further establishes the importance of using a correct scattering phase function model while estimating the channel capacity of UWOC system in terms of the received power and channel impulse response. Results further demonstrate a great advantage of considering the nonzero probability of receiving scattered photons in estimating channel capacity rather than considering the reception of only ballistic photons as in Beer's Law, which severely underestimates the received power and affects the range of communication especially in the scattering water column. The received power computed based on the Monte-Carlo method by considering the receiver aperture sizes and field of views in different water types are further analyzed and discussed. These results are essential for evaluating the underwater link budget and constructing different system and design parameters for an UWOC system.

Matrix effect of sodium compounds on the determination of metal ions in aqueous solutions by underwater laser-induced breakdown spectroscopy

DOE PAGES

Goueguel, Christian; McIntyre, Dustin L.; Jain, Jinesh; ...

2015-06-30

A significant portion of the carbon sequestration research being performed in the United States involves the risk assessment of injecting large quantities of carbon dioxide into deep saline aquifers. Leakage of CO 2 has the potential to affect the quality of groundwater supplies in case contaminants migrate through underlying conduits. New remote sensing and near-surface monitoring technologies are needed to ensure that injection, abandoned, and monitoring wells are structurally sound, and that CO 2 remains within the geologic storage reservoir. In this paper, we propose underwater laser-induced breakdown spectroscopy (underwater LIBS) as an analytical method for monitoring naturally occurring elementsmore » that can act as tracers to detect a CO 2 leak from storage sites. Laboratory-scale experiments were conducted to measure Sr 2+, Ca 2+, K +, and Li + in bulk solutions to ascertain the analytical performance of underwater LIBS. We compared the effect of NaCl, Na 2CO 3, and Na 2SO 4 on the analytes calibration curves to determine underwater LIBS’ ability to analyze samples of sodium compounds. In all cases, the calibration curves showed a good linearity within 2 orders of magnitude. The limit of detections (LODs) obtained for K + (30±1 ppb) and Li + (60±2 ppb) were in ppb range, while higher LODs were observed for Ca 2+ (0.94±0.14 ppm) and Sr 2+ (2.89±0.11 ppm). Evaluation of the calibration curves for the analytes in mixed solutions showed dependence of the lines’ intensity with the sodium compounds. The intensities increased respectively in the presence of dissolved NaCl and Na 2SO 4, whereas the intensities slightly decreased in the presence of Na 2CO 3. Lastly, the capabilities of underwater LIBS to detect certain elements in the ppb or in the low ppm range make it particularly appealing for in situ monitoring of a CO 2 leak.« less

Matrix effect of sodium compounds on the determination of metal ions in aqueous solutions by underwater laser-induced breakdown spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goueguel, Christian; McIntyre, Dustin L.; Jain, Jinesh

A significant portion of the carbon sequestration research being performed in the United States involves the risk assessment of injecting large quantities of carbon dioxide into deep saline aquifers. Leakage of CO 2 has the potential to affect the quality of groundwater supplies in case contaminants migrate through underlying conduits. New remote sensing and near-surface monitoring technologies are needed to ensure that injection, abandoned, and monitoring wells are structurally sound, and that CO 2 remains within the geologic storage reservoir. In this paper, we propose underwater laser-induced breakdown spectroscopy (underwater LIBS) as an analytical method for monitoring naturally occurring elementsmore » that can act as tracers to detect a CO 2 leak from storage sites. Laboratory-scale experiments were conducted to measure Sr 2+, Ca 2+, K +, and Li + in bulk solutions to ascertain the analytical performance of underwater LIBS. We compared the effect of NaCl, Na 2CO 3, and Na 2SO 4 on the analytes calibration curves to determine underwater LIBS’ ability to analyze samples of sodium compounds. In all cases, the calibration curves showed a good linearity within 2 orders of magnitude. The limit of detections (LODs) obtained for K + (30±1 ppb) and Li + (60±2 ppb) were in ppb range, while higher LODs were observed for Ca 2+ (0.94±0.14 ppm) and Sr 2+ (2.89±0.11 ppm). Evaluation of the calibration curves for the analytes in mixed solutions showed dependence of the lines’ intensity with the sodium compounds. The intensities increased respectively in the presence of dissolved NaCl and Na 2SO 4, whereas the intensities slightly decreased in the presence of Na 2CO 3. Lastly, the capabilities of underwater LIBS to detect certain elements in the ppb or in the low ppm range make it particularly appealing for in situ monitoring of a CO 2 leak.« less

Experimental and Theoretical Analysis of Sound Absorption Properties of Finely Perforated Wooden Panels

PubMed Central

Song, Boqi; Peng, Limin; Fu, Feng; Liu, Meihong; Zhang, Houjiang

2016-01-01

Perforated wooden panels are typically utilized as a resonant sound absorbing material in indoor noise control. In this paper, the absorption properties of wooden panels perforated with tiny holes of 1–3 mm diameter were studied both experimentally and theoretically. The Maa-MPP (micro perforated panels) model and the Maa-Flex model were applied to predict the absorption regularities of finely perforated wooden panels. A relative impedance comparison and full-factorial experiments were carried out to verify the feasibility of the theoretical models. The results showed that the Maa-Flex model obtained good agreement with measured results. Control experiments and measurements of dynamic mechanical properties were carried out to investigate the influence of the wood characteristics. In this study, absorption properties were enhanced by sound-induced vibration. The relationship between the dynamic mechanical properties and the panel mass-spring vibration absorption was revealed. While the absorption effects of wood porous structure were not found, they were demonstrated theoretically by using acoustic wave propagation in a simplified circular pipe with a suddenly changed cross-section model. This work provides experimental and theoretical guidance for perforation parameter design. PMID:28774063

A Novel Acoustic Sensor Approach to Classify Seeds Based on Sound Absorption Spectra

PubMed Central

Gasso-Tortajada, Vicent; Ward, Alastair J.; Mansur, Hasib; Brøchner, Torben; Sørensen, Claus G.; Green, Ole

2010-01-01

A non-destructive and novel in situ acoustic sensor approach based on the sound absorption spectra was developed for identifying and classifying different seed types. The absorption coefficient spectra were determined by using the impedance tube measurement method. Subsequently, a multivariate statistical analysis, i.e., principal component analysis (PCA), was performed as a way to generate a classification of the seeds based on the soft independent modelling of class analogy (SIMCA) method. The results show that the sound absorption coefficient spectra of different seed types present characteristic patterns which are highly dependent on seed size and shape. In general, seed particle size and sphericity were inversely related with the absorption coefficient. PCA presented reliable grouping capabilities within the diverse seed types, since the 95% of the total spectral variance was described by the first two principal components. Furthermore, the SIMCA classification model based on the absorption spectra achieved optimal results as 100% of the evaluation samples were correctly classified. This study contains the initial structuring of an innovative method that will present new possibilities in agriculture and industry for classifying and determining physical properties of seeds and other materials. PMID:22163455

Wall structure and material properties cause viscous damping of swimbladder sounds in the oyster toadfish Opsanus tau

PubMed Central

King, Terrence L.; Ali, Heba; Sidker, Nehan; Cameron, Timothy M.

2016-01-01

Despite rapid damping, fish swimbladders have been modelled as underwater resonant bubbles. Recent data suggest that swimbladders of sound-producing fishes use a forced rather than a resonant response to produce sound. The reason for this discrepancy has not been formally addressed, and we demonstrate, for the first time, that the structure of the swimbladder wall will affect vibratory behaviour. Using the oyster toadfish Opsanus tau, we find regional differences in bladder thickness, directionality of collagen layers (anisotropic bladder wall structure), material properties that differ between circular and longitudinal directions (stress, strain and Young's modulus), high water content (80%) of the bladder wall and a 300-fold increase in the modulus of dried tissue. Therefore, the swimbladder wall is a viscoelastic structure that serves to damp vibrations and impart directionality, preventing the expression of resonance. PMID:27798293

Dual-frequency sound-absorbing metasurface based on visco-thermal effects with frequency dependence

NASA Astrophysics Data System (ADS)

Ryoo, H.; Jeon, W.

2018-03-01

We investigate theoretically an acoustic metasurface with a high absorption coefficient at two frequencies and design it from subwavelength structures. We propose the use of a two-dimensional periodic array of four Helmholtz resonators in two types to obtain a metasurface with nearly perfect sound absorption at given target frequencies via interactions between waves emanating from different resonators. By considering how fluid viscosity affects acoustic energy dissipation in the narrow necks of the Helmholtz resonators, we obtain effective complex-valued material properties that depend on frequency and on the geometrical parameters of the resonators. We furthermore derive the effective acoustic impedance of the metasurface from the effective material properties and calculate the absorption spectra from the theoretical model, which we compare with the spectra obtained from a finite-element simulation. As a practical application of the theoretical model, we derive empirical formulas for the geometrical parameters of a metasurface which would yield perfect absorption at a given frequency. While previous works on metasurfaces based on Helmholtz resonators aimed to absorb sound at single frequencies, we use optimization to design a metasurface composed of four different Helmholtz resonators to absorb sound at two distinct frequencies.

The Application of Coconut Fiber as Dissipative Silencer

NASA Astrophysics Data System (ADS)

Madlan, M. A.; Ghazali, M. I.; Zaman, I.; Kasron, M. Z.; Ying, T. C.

2017-01-01

Heat ventilation air conditioning system (HVAC) is one of the ducting systems that broadly applied in the building. There are HVAC silencers in the market, however the sound absorptive material commonly used is mineral wool. In this research study, a sound absorptive material made of coconut fiber was tested to identify its performance as a potential replacement of green material for ducting silencer. The experiment was carried out in a testing apparatus that follows the BS EN ISO 11691:2009 standard. Different configurations of sound absorptive material and contents of coconut fiber were investigated in the study. The trend of insertion loss at 1/3 octave frequency was identified where at frequency below 3000Hz, the insertion loss of dissipative silencer is observed high at certain frequency with a very narrow range. At 3000Hz, the insertion loss of 4dB to 6dB is constant until 4000Hz and drops until 5000Hz before it increases again steadily up to 13dB at 10000Hz. A similar trend was observed for different configuration of sound absorptive material. Despite the configuration different, the outcome shows that the insertion loss is increasing with higher content of coconut fiber.

Measuring Coastal Boating Noise to Assess Potential Impacts on Marine Life

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matzner, Shari; Jones, Mark E.

2011-07-01

Article requested for submission in Sea Technology Magazine describing the Underwater Noise From Small Boats. An Overlooked Component of the Acoustic Environment in Coastal Areas. Underwater noise and its effects on marine life deserve attention as human activity in the marine environment increases. Noise can affect fish and marine mammals in ways that are physiological, as in auditory threshold shifts, and behavioral, as in changes in foraging habits. One anthropogenic source of underwater noise that has received little attention to date is recreational boating. Coastal areas and archipelago regions, which play a crucial role in the marine ecosystem, are oftenmore » subject to high levels of boat traffic. In order to better understand the noise produced by a small powerboat, a test was conducted in Sequim Bay, Washington, using an instrumented research vessel and multiple acoustic sensors. The broadband noise and narrowband peak levels were observed from two different locations while the boat was operated under various conditions. The results, combined with background noise levels, sound propagation and local boat traffic patterns, can provide a picture of the total boating noise to which marine life may be subjected.« less

Acoustic deterrence of bighead carp (Hypophthalmichthys nobilis) to a broadband sound stimulus

USGS Publications Warehouse

Vetter, Brooke J.; Murchy, Kelsie; Cupp, Aaron R.; Amberg, Jon J.; Gaikowski, Mark P.; Mensinger, Allen F.

2017-01-01

Recent studies have shown the potential of acoustic deterrents against invasive silver carp (Hypophthalmichthys molitrix). This study examined the phonotaxic response of the bighead carp (H. nobilis) to pure tones (500–2000 Hz) and playbacks of broadband sound from an underwater recording of a 100 hp outboard motor (0.06–10 kHz) in an outdoor concrete pond (10 × 5 × 1.2 m) at the U.S. Geological Survey Upper Midwest Environmental Science Center in La Crosse, WI. The number of consecutive times the fish reacted to sound from alternating locations at each end of the pond was assessed. Bighead carp were relatively indifferent to the pure tones with median consecutive responses ranging from 0 to 2 reactions away from the sound source. However, fish consistently exhibited significantly (P < 0.001) greater negative phonotaxis to the broadband sound (outboard motor recording) with an overall median response of 20 consecutive reactions during the 10 min trials. In over 50% of broadband sound tests, carp were still reacting to the stimulus at the end of the trial, implying that fish were not habituating to the sound. This study suggests that broadband sound may be an effective deterrent to bighead carp and provides a basis for conducting studies with wild fish.

Estimating the sound speed of a shallow-water marine sediment from the head wave excited by a low-flying helicopter.

PubMed

Bevans, Dieter A; Buckingham, Michael J

2017-10-01

The frequency bandwidth of the sound from a light helicopter, such as a Robinson R44, extends from about 13 Hz to 2.5 kHz. As such, the R44 has potential as a low-frequency sound source in underwater acoustics applications. To explore this idea, an experiment was conducted in shallow water off the coast of southern California in which a horizontal line of hydrophones detected the sound of an R44 hovering in an end-fire position relative to the array. Some of the helicopter sound interacted with seabed to excite the head wave in the water column. A theoretical analysis of the sound field in the water column generated by a stationary airborne source leads to an expression for the two-point horizontal coherence function of the head wave, which, apart from frequency, depends only on the sensor separation and the sediment sound speed. By matching the zero crossings of the measured and theoretical horizontal coherence functions, the sound speed in the sediment was recovered and found to take a value of 1682.42 ± 16.20 m/s. This is consistent with the sediment type at the experiment site, which is known from a previous survey to be a fine to very-fine sand.

Vector Acoustics, Vector Sensors, and 3D Underwater Imaging

NASA Astrophysics Data System (ADS)

Lindwall, D.

2007-12-01

Vector acoustic data has two more dimensions of information than pressure data and may allow for 3D underwater imaging with much less data than with hydrophone data. The vector acoustic sensors measures the particle motions due to passing sound waves and, in conjunction with a collocated hydrophone, the direction of travel of the sound waves. When using a controlled source with known source and sensor locations, the reflection points of the sound field can be determined with a simple trigonometric calculation. I demonstrate this concept with an experiment that used an accelerometer based vector acoustic sensor in a water tank with a short-pulse source and passive scattering targets. The sensor consists of a three-axis accelerometer and a matched hydrophone. The sound source was a standard transducer driven by a short 7 kHz pulse. The sensor was suspended in a fixed location and the hydrophone was moved about the tank by a robotic arm to insonify the tank from many locations. Several floats were placed in the tank as acoustic targets at diagonal ranges of approximately one meter. The accelerometer data show the direct source wave as well as the target scattered waves and reflections from the nearby water surface, tank bottom and sides. Without resorting to the usual methods of seismic imaging, which in this case is only two dimensional and relied entirely on the use of a synthetic source aperture, the two targets, the tank walls, the tank bottom, and the water surface were imaged. A directional ambiguity inherent to vector sensors is removed by using collocated hydrophone data. Although this experiment was in a very simple environment, it suggests that 3-D seismic surveys may be achieved with vector sensors using the same logistics as a 2-D survey that uses conventional hydrophones. This work was supported by the Office of Naval Research, program element 61153N.

About sound mufflers sound-absorbing panels aircraft engine

NASA Astrophysics Data System (ADS)

Dudarev, A. S.; Bulbovich, R. V.; Svirshchev, V. I.

2016-10-01

The article provides a formula for calculating the frequency of sound absorbed panel with a perforated wall. And although the sound absorbing structure is a set of resonators Helmholtz, not individual resonators should be considered in acoustic calculations, and all the perforated wall panel. The analysis, showing how the parameters affect the size and sound-absorbing structures in the absorption rate.

The directivity of the sound radiation from panels and openings.

PubMed

Davy, John L

2009-06-01

This paper presents a method for calculating the directivity of the radiation of sound from a panel or opening, whose vibration is forced by the incidence of sound from the other side. The directivity of the radiation depends on the angular distribution of the incident sound energy in the room or duct in whose wall or end the panel or opening occurs. The angular distribution of the incident sound energy is predicted using a model which depends on the sound absorption coefficient of the room or duct surfaces. If the sound source is situated in the room or duct, the sound absorption coefficient model is used in conjunction with a model for the directivity of the sound source. For angles of radiation approaching 90 degrees to the normal to the panel or opening, the effect of the diffraction by the panel or opening, or by the finite baffle in which the panel or opening is mounted, is included. A simple empirical model is developed to predict the diffraction of sound into the shadow zone when the angle of radiation is greater than 90 degrees to the normal to the panel or opening. The method is compared with published experimental results.

Pilot study: Exposure and materiality of the secondary room and its impact in the impulse response of coupled-volume concert halls

NASA Astrophysics Data System (ADS)

Ermann, Michael; Johnson, Marty E.

2002-05-01

What does one room sound like when it is partially exposed to another (acoustically coupled)? More specifically, this research aims to quantify how operational and design decisions impact aural impressions in the design of concert halls with acoustical coupling. By adding a second room to a concert hall, and designing doors to control the sonic transparency between the two rooms, designers can create a new, coupled acoustic. Concert halls use coupling to achieve a variable, longer, and distinct reverberant quality for their musicians and listeners. For this study, a coupled-volume shoebox concert hall was conceived with a fixed geometric volume, form, and primary-room sound absorption. Aperture size and secondary-room sound-absorption levels were established as variables. Statistical analysis of sound decay in this simulated hall suggests a highly sensitive relationship between the double-sloped condition and (1) Architectural composition, as defined by the aperture size exposing the chamber and (2) Materiality, as defined by the sound absorbance in the coupled volume. Preliminary calculations indicate that the double-sloped sound decay condition only appears when the total aperture area is less than 1.5% of the total shoebox surface area and the average absorption coefficient of the coupled volume is less than 0.07.

Underwater inverse LIBS (iLIBS) for marine archaeology

NASA Astrophysics Data System (ADS)

Asmus, J.; Magde, M.; Elford, J.; Magde, D.; Parfenov, V.

2013-05-01

In recent years there have been enormous advances in nautical archaeology through developments in SONAR technologies as well as in manned and robotic submersible vehicles. The number of sunken vessel discoveries has escalated in many of the seas of the world in response to the widespread application of these and other new tools. Customarily, surviving artifacts within the debris field of a wreck are collected and then moved to laboratories, centers, or institutions for analyses and possible conservation. Frequently, the conservation phase involves chemical treatments to stabilize an artefact to standard temperature, pressure, and humidity instead of an undersea environment. Many of the artefacts encountered at an underwater site are now characterized and restored in-situ in accordance with modern trends in art conservation. Two examples of this trend are exemplified by the resting place of the wreck of the Titanic in the Atlantic and the Cancun Underwater Park in the Caribbean Sea. These two debris fields have been turned into museums for diving visitors. Several research groups have investigated the possibility of adapting the well-established analytical tool Laser Induced Breakdown Spectroscopy (LIBS) to in-situ elemental analyses of underwater cultural, historic, and archaeological artefacts where discovered, rather than as a phase of a salvage operation. As the underwater laser ablation associated with LIBS generates a "snowplough" shockwave within the aqueous matrix, the atomic emission spectrum is usually severely attenuated in escaping from the target. Consequently, probative experiments to date generally invoke a submerged air chamber or air jet to isolate water from the interaction zone as well as employ more complex double-pulse lasers. These measures impose severe logistical constraints on the examination of widely dispersed underwater artefacts. In order to overcome this constraint we report on water-immersion LIBS experiments performed with oblique laser irradiation and spectral detection at the complementary angle so as to view emission from behind the shockwave. Targets of silver, gold, and copper have been studied. It is found that this approach enables LIBS detection in water both in emission and in absorption. It appears that underwater inverse LIBS may be especially useful in underwater archaeology.

A Study of Underwater Sound Ray Tracing Methodology

DTIC Science & Technology

1990-09-01

SRER ,LB,SV,SVU2,SVU,SU2,SU4,GI,G PIE = 3.14159265359D0 77 lEST = 0 MI = M C DISTRIBUTE THE K SOURCES EQUALLY AROUND THE CIRCLE COUNTER C CLOCKWISE...C(I) - TI-R(I TIMER(I = TIMCO) - T(5) HER(IW HC(I - Hl ZER(IW ZC(I - ZI SR = DSQRT(HI**2 + WA - Zl)**2) SRER = DSQRT(HC(I)**2 + (A2 - Zl)**2) - SR 50

Piezocomposites for Active Surface Control

DTIC Science & Technology

1999-01-19

and the Underwater Sound Reference Detachment (USRD) in Orlando, FL. During the period of the program, USRD became part of the Naval Undersea Warfare...Appendix B DEPARTMENT OF THE NAVY NAVAL UNDERSEA WARFARE CENTER 1176 HOWELL STREET NEWPORT Rl 02«41-170i NAVAL UNDERSEA WARFARE CENTER...dissemination only as directed by Commanding Officer, Naval Undersea Warfare Center (18 AUG i99o ) or higher DoD authority. Page 1 of 1 USRD CALIBRATION

Nonlinear Optoacoustic Underwater Sound.

DTIC Science & Technology

1988-01-11

sufficiently high plasma densities, the plasma itself may act as an acoustic ] amplifier, channeling electronic energy into acoustic energy. The shock pulse... channeled into the production of electron charge carriers, the law of conservation of energy dictates that the upperbound of the electron yield must be...temperature of the water by approximately 10C from room 100 - t bLT WV *A% IV * , . . ..1- KV7 b * .% r.- V-V I 7 TABLE V 0 EQUILIBRIUM BLAST MODEL CASE

Sound-proof Sandwich Panel Design via Metamaterial Concept

NASA Astrophysics Data System (ADS)

Sui, Ni

Sandwich panels consisting of hollow core cells and two face-sheets bonded on both sides have been widely used as lightweight and strong structures in practical engineering applications, but with poor acoustic performance especially at low frequency regime. Basic sound-proof methods for the sandwich panel design are spontaneously categorized as sound insulation and sound absorption. Motivated by metamaterial concept, this dissertation presents two sandwich panel designs without sacrificing weight or size penalty: A lightweight yet sound-proof honeycomb acoustic metamateiral can be used as core material for honeycomb sandwich panels to block sound and break the mass law to realize minimum sound transmission; the other sandwich panel design is based on coupled Helmholtz resonators and can achieve perfect sound absorption without sound reflection. Based on the honeycomb sandwich panel, the mechanical properties of the honeycomb core structure were studied first. By incorporating a thin membrane on top of each honeycomb core, the traditional honeycomb core turns into honeycomb acoustic metamaterial. The basic theory for such kind of membrane-type acoustic metamaterial is demonstrated by a lumped model with infinite periodic oscillator system, and the negative dynamic effective mass density for clamped membrane is analyzed under the membrane resonance condition. Evanescent wave mode caused by negative dynamic effective mass density and impedance methods are utilized to interpret the physical phenomenon of honeycomb acoustic metamaterials at resonance. The honeycomb metamaterials can extraordinarily improve low-frequency sound transmission loss below the first resonant frequency of the membrane. The property of the membrane, the tension of the membrane and the numbers of attached membranes can impact the sound transmission loss, which are observed by numerical simulations and validated by experiments. The sandwich panel which incorporates the honeycomb metamateiral as the core material maintains the mechanical property and yields a sound transmission loss that is consistently greater than 50 dB at low frequencies. Furthermore, the absorption property of the proposed honeycomb sandwich panel was experimentally studied. The honeycomb sandwich panel shows an excellent sound absorbing performance at high frequencies by using reinforced glass fiber without adding too much mass. The effect of the panel size and the stiffness of the grid-like frame effect of the honeycomb sandwich structures on sound transmission are discussed lastly. For the second sound-proof sandwich panel design, each unit cell of the sandwich panel is replaced by a Helmholtz resonator by perforating a small hole on the top face sheet. A perfect sound absorber sandwich panel with coupled Helmholtz resonators is proposed by two types: single identical Helmholtz resonator in each unit cell and dual Helmholtz resonators with different orifices, arranged in each cell arranged periodically. The soundproof sandwich panel is modelled as a panel embedded in rigid panel and assumed as a semiinfinite space with hard boundary condition. The net/mutual impedance model is first proposed and derived by solving Kirchhoff-Helmholtz integral by using the Green's function. The thermal-viscous energy dissipation at the thermal boundary layer dominates the total energy consumed. Two types of perfect sound absorber sandwich panel are designed in the last part. Two theoretical methods: the average energy and the equivalent surface impedance method are used to predict sound absorption performance. The geometry for perfect sound absorber sandwich panel at a target frequency can be obtained when the all the Helmholtz resonators are at resonance and the surface impedance of the sandwich panel matches the air impedance. The bandwidth for the identical sandwich panel mainly depends on the neck radius. The absorptive property of the dual Helmholtz resonators type of sandwich panel is studied by investigating the coupling effects between HRs. The theoretical results can be verified by numerical simulations through finite element method. The absorption bandwidth can be tuned by incorporating more HRs in each unit cell. Both sound-proof sandwich panel designs possess extraordinary acoustic performance for noise reduction at low frequency range with sub-wavelength structures. The sound absorber panel design can also achieve broadband sound attenuation at low frequencies.

Potential interactions between diadromous fishes of U.K. conservation importance and the electromagnetic fields and subsea noise from marine renewable energy developments.

PubMed

Gill, A B; Bartlett, M; Thomsen, F

2012-07-01

The considerable extent of construction and operation of marine renewable energy developments (MRED) within U.K. and adjacent waters will lead, among other things, to the emission of electromagnetic fields (EMF) and subsea sounds into the marine environment. Migratory fishes that respond to natural environmental cues, such as the Earth's geomagnetic field or underwater sounds, move through the same waters that the MRED occupy, thereby raising the question of whether there are any effects of MRED on migratory fishes. Diadromous species, such as the Salmonidae and Anguillidae, which undertake large-scale migrations through coastal and offshore waters, are already significantly affected by other human activities leading to national and international conservation efforts to manage any existing threats and to minimize future concerns, including the potential effect of MRED. Here, the current state of knowledge with regard to the potential for diadromous fishes of U.K. conservation importance to be affected by MRED is reviewed. The information on which to base the review was found to be limited with respect to all aspects of these fishes' migratory behaviour and activity, especially with regards to MRED deployment, making it difficult to establish cause and effect relationships. The main findings, however, were that diadromous species can use the Earth's magnetic field for orientation and direction finding during migrations. Juveniles of anadromous brown trout (sea trout) Salmo trutta and close relatives of S. trutta respond to both the Earth's magnetic field and artificial magnetic fields. Current knowledge suggests that EMFs from subsea cables may interact with migrating Anguilla sp. (and possibly other diadromous fishes) if their movement routes take them over the cables, particularly in shallow water (<20 m). The only known effect is a temporary change in swimming direction. Whether this will represent a biologically significant effect, for example delayed migration, cannot yet be determined. Diadromous fishes are likely to encounter EMFs from subsea cables either during the adult movement phases of life or their early life stages during migration within shallow, coastal waters adjacent to natal rivers. The underwater sound from MRED devices has not been fully characterized to determine its acoustic properties and propagation through the coastal waters. MRED that require pile driving during construction appear to be the most relevant to consider. In the absence of a clear understanding of their response to underwater sound, the specific effects on migratory species of conservation concern remain very difficult to determine in relation to MRED. Based on the studies reviewed, it is suggested that fishes that receive high intensity sound in close proximity to construction may be physiologically affected to some degree, whereas those at farther distances, potentially up to several km, may exhibit behaviour responses; the effect of which is unknown and will be dependent on the properties of the received sound and receptor characteristics and condition. Whether there are behavioural effects on the fishes during operation is unknown but any change to the environment and subsequent response by the fishes would need to be considered over the lifetime of the MRED. It is not yet possible to determine if effects relating to sound exposure are biologically significant. The current assumptions of limited effects are built on an incomplete understanding of how the species move around their environment and interact with natural and anthropogenic EMFs and subsea sound. A number of important knowledge gaps exist, principally whether migratory fish species on the whole respond to the EMF and the sound associated with MRED. Future research should address the principal gaps before assuming that any effect on diadromous species results in a biological effect. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

A variable passive low-frequency absorber

NASA Astrophysics Data System (ADS)

Larsen, Niels Werner; Thompson, Eric R.; Gade, Anders Christian

2005-04-01

Multi-purpose concert halls face a dilemma. They can host classical music concerts, rock concerts and spoken word performances in a matter of a short period. These different performance types require significantly different acoustic conditions in order to provide the best sound quality to both the performers and the audience. A recommended reverberation time for classical music may be in the range of 1.5-2 s for empty halls, where rock music sounds best with a reverberation time around 0.8-1 s. Modern rhythmic music often contains high levels of sound energy in the low frequency bands but still requires a high definition for good sound quality. Ideally, the absorption of the hall should be adjustable in all frequency bands in order to provide good sound quality for all types of performances. The mid and high frequency absorption is easily regulated, but adjusting the low-frequency absorption has typically been too expensive or requires too much space to be practical for multi-purpose halls. Measurements were made on a variable low-frequency absorber to develop a practical solution to the dilemma. The paper will present the results of the measurements as well as a possible design.

Effects of hydrokinetic turbine sound on the behavior of four species of fish within an experimental mesocosm

DOE PAGES

Schramm, Michael P.; Bevelhimer, Mark; Scherelis, Constantin

2017-02-04

The development of hydrokinetic energy technologies (e.g., tidal turbines) has raised concern over the potential impacts of underwater sound produced by hydrokinetic turbines on fish species likely to encounter these turbines. To assess the potential for behavioral impacts, we exposed four species of fish to varying intensities of recorded hydrokinetic turbine sound in a semi-natural environment. Although we tested freshwater species (redhorse suckers [Moxostoma spp], freshwater drum [Aplondinotus grunniens], largemouth bass [Micropterus salmoides], and rainbow trout [Oncorhynchus mykiss]), these species are also representative of the hearing physiology and sensitivity of estuarine species that would be affected at tidal energy sites.more » Here, we evaluated changes in fish position relative to different intensities of turbine sound as well as trends in location over time with linear mixed-effects and generalized additive mixed models. We also evaluated changes in the proportion of near-source detections relative to sound intensity and exposure time with generalized linear mixed models and generalized additive models. Models indicated that redhorse suckers may respond to sustained turbine sound by increasing distance from the sound source. Freshwater drum models suggested a mixed response to turbine sound, and largemouth bass and rainbow trout models did not indicate any likely responses to turbine sound. Lastly, findings highlight the importance for future research to utilize accurate localization systems, different species, validated sound transmission distances, and to consider different types of behavioral responses to different turbine designs and to the cumulative sound of arrays of multiple turbines.« less

Effects of hydrokinetic turbine sound on the behavior of four species of fish within an experimental mesocosm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schramm, Michael P.; Bevelhimer, Mark; Scherelis, Constantin

The development of hydrokinetic energy technologies (e.g., tidal turbines) has raised concern over the potential impacts of underwater sound produced by hydrokinetic turbines on fish species likely to encounter these turbines. To assess the potential for behavioral impacts, we exposed four species of fish to varying intensities of recorded hydrokinetic turbine sound in a semi-natural environment. Although we tested freshwater species (redhorse suckers [Moxostoma spp], freshwater drum [Aplondinotus grunniens], largemouth bass [Micropterus salmoides], and rainbow trout [Oncorhynchus mykiss]), these species are also representative of the hearing physiology and sensitivity of estuarine species that would be affected at tidal energy sites.more » Here, we evaluated changes in fish position relative to different intensities of turbine sound as well as trends in location over time with linear mixed-effects and generalized additive mixed models. We also evaluated changes in the proportion of near-source detections relative to sound intensity and exposure time with generalized linear mixed models and generalized additive models. Models indicated that redhorse suckers may respond to sustained turbine sound by increasing distance from the sound source. Freshwater drum models suggested a mixed response to turbine sound, and largemouth bass and rainbow trout models did not indicate any likely responses to turbine sound. Lastly, findings highlight the importance for future research to utilize accurate localization systems, different species, validated sound transmission distances, and to consider different types of behavioral responses to different turbine designs and to the cumulative sound of arrays of multiple turbines.« less

Acoustic Properties of Polyurethane Composition Reinforced with Carbon Nanotubes and Silicon Oxide Nano-powder

NASA Astrophysics Data System (ADS)

Orfali, Wasim A.

This article demonstrates the acoustic properties of added small amount of carbon-nanotube and siliconoxide nano powder (S-type, P-Type) to the host material polyurethane composition. By adding CNT and/or nano-silica in the form of powder at different concentrations up to 2% within the PU composition to improve the sound absorption were investigated in the frequency range up to 1600 Hz. Sound transmission loss measurement of the samples were determined using large impedance tube. The tests showed that addition of 0.2 wt.% Silicon Oxide Nano-powder and 0.35 wt.% carbon nanotube to polyurethane composition improved sound transmissions loss (Sound Absorption) up to 80 dB than that of pure polyurethane foam sample.

Directional Acoustic Wave Manipulation by a Porpoise via Multiphase Forehead Structure

NASA Astrophysics Data System (ADS)

Zhang, Yu; Song, Zhongchang; Wang, Xianyan; Cao, Wenwu; Au, Whitlow W. L.

2017-12-01

Porpoises are small-toothed whales, and they can produce directional acoustic waves to detect and track prey with high resolution and a wide field of view. Their sound-source sizes are rather small in comparison with the wavelength so that beam control should be difficult according to textbook sonar theories. Here, we demonstrate that the multiphase material structure in a porpoise's forehead is the key to manipulating the directional acoustic field. Computed tomography (CT) derives the multiphase (bone-air-tissue) complex, tissue experiments obtain the density and sound-velocity multiphase gradient distributions, and acoustic fields and beam formation are numerically simulated. The results suggest the control of wave propagations and sound-beam formations is realized by cooperation of the whole forehead's tissues and structures. The melon size significantly impacts the side lobes of the beam and slightly influences the main beams, while the orientation of the vestibular sac mainly adjusts the main beams. By compressing the forehead complex, the sound beam can be expanded for near view. The porpoise's biosonar allows effective wave manipulations for its omnidirectional sound source, which can help the future development of miniaturized biomimetic projectors in underwater sonar, medical ultrasonography, and other ultrasonic imaging applications.

Understanding auditory distance estimation by humpback whales: a computational approach.

PubMed

Mercado, E; Green, S R; Schneider, J N

2008-02-01

Ranging, the ability to judge the distance to a sound source, depends on the presence of predictable patterns of attenuation. We measured long-range sound propagation in coastal waters to assess whether humpback whales might use frequency degradation cues to range singing whales. Two types of neural networks, a multi-layer and a single-layer perceptron, were trained to classify recorded sounds by distance traveled based on their frequency content. The multi-layer network successfully classified received sounds, demonstrating that the distorting effects of underwater propagation on frequency content provide sufficient cues to estimate source distance. Normalizing received sounds with respect to ambient noise levels increased the accuracy of distance estimates by single-layer perceptrons, indicating that familiarity with background noise can potentially improve a listening whale's ability to range. To assess whether frequency patterns predictive of source distance were likely to be perceived by whales, recordings were pre-processed using a computational model of the humpback whale's peripheral auditory system. Although signals processed with this model contained less information than the original recordings, neural networks trained with these physiologically based representations estimated source distance more accurately, suggesting that listening whales should be able to range singers using distance-dependent changes in frequency content.

Acoustic impedance properties of seafloor sediments off the coast of Southeastern Hainan, South China Sea

NASA Astrophysics Data System (ADS)

Hou, Zhengyu; Chen, Zhong; Wang, Jingqiang; Zheng, Xufeng; Yan, Wen; Tian, Yuhang; Luo, Yun

2018-04-01

Geoacoustic parameters are essential inputs to sediment wave propagation theories and are vital to underwater acoustic environment and explorations of the sea bottom. In this study, 21 seafloor sediment samples were collected off the coast of southeastern Hainan in the South China Sea. The sound speed was measured using a portable WSD-3 digital sonic instrument and the coaxial differential distance measurement method. Based on the measured sound speed and physical properties, the acoustic impedance and the pore-water-independent index of impedance (IOI) were calculated in this study. Similar to the sound speed, the IOI values are closely related to the sediment physical properties and change gradually from the northwest to the southeast. The relations between IOI and physical properties were studied and compared to the relations between the sound speed and physical properties. IOI is better correlated to physical properties than sound speed. This study also uses an error norm method to analyze the sensitivity of IOI to the physical parameters in the double-parameter equations and finds that the most influential physical parameters are as follows: wet bulk density > porosity > clay content > mean particle size.

Study of flight data recorder, underwater locator beacon, data logger and flarm collision avoidance system

NASA Astrophysics Data System (ADS)

Timi, Purnota Hannan; Shermin, Saima; Rahman, Asifur

2017-06-01

Flight data recorder is one of the most important sources of flight data in event of aviation disaster which records a wide range of flight parameters including altitude, airspeed, heading etc. and also helps monitoring and analyzing aircraft performance. Cockpit voice recorder records radio microphone transmissions and sounds in the cockpit. These devices help to find out and understand the root causes of aircraft crashes and help building better aircraft systems and technical solutions to prevent similar type of crashes in future, which lead to improvement in safety of aircrafts and passengers. There are other devices also which enhance the aircraft safety and assists in emergency or catastrophic situations. This paper discusses the concept of Flight Data Recorder (FDR), Cockpit Voice Recorder (CVR), Underwater Locator Beacon (ULB), Data logger and flarm-collision avoidance system for aircraft and their applications in aviation.

Masking in three pinnipeds: underwater, low-frequency critical ratios.

PubMed

Southall, B L; Schusterman, R J; Kastak, D

2000-09-01

Behavioral techniques were used to determine underwater masked hearing thresholds for a northern elephant seal (Mirounga angustirostris), a harbor seal (Phoca vitulina), and a California sea lion (Zalophus californianus). Octave-band white noise maskers were centered at five test frequencies ranging from 200 to 2500 Hz; a slightly wider noise band was used for testing at 100 Hz. Critical ratios were calculated at one masking noise level for each test frequency. Above 200 Hz, critical ratios increased with frequency. This pattern is similar to that observed in most animals tested, and indicates that these pinnipeds lack specializations for detecting low-frequency tonal sounds in noise. However, the individual pinnipeds in this study, particularly the northern elephant seal, detected signals at relatively low signal-to-noise ratios. These results provide a means of estimating zones of auditory masking for pinnipeds exposed to anthropogenic noise sources.

Behavioral responses of gray whales to industrial noise: feeding observations and predictive modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malme, C.I.; Wuersig, B.; Bird, J.E.

1986-08-01

An investigation was made of the potential effects of underwater noise from petroleum-industry activities on feeding gray whales. The investigation consisted of two components, a field study and an acoustic model study. The field study was performed near Southeast Cape, St. Lawrence Island in August, 1985, using a 100 cu. in. air gun source and playback of drillship noise. Sound-source levels and acoustic-propagation losses were measured to permit estimation of sound exposure levels at whale-sighting positions. For the air-gun source there was a 0.5 probability that the whales would stop feeding and move away from the area when the averagemore » pulse levels reached 173 dB.« less

The Development of a Finite Volume Method for Modeling Sound in Coastal Ocean Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Wen; Yang, Zhaoqing; Copping, Andrea E.

: As the rapid growth of marine renewable energy and off-shore wind energy, there have been concerns that the noises generated from construction and operation of the devices may interfere marine animals’ communication. In this research, a underwater sound model is developed to simulate sound prorogation generated by marine-hydrokinetic energy (MHK) devices or offshore wind (OSW) energy platforms. Finite volume and finite difference methods are developed to solve the 3D Helmholtz equation of sound propagation in the coastal environment. For finite volume method, the grid system consists of triangular grids in horizontal plane and sigma-layers in vertical dimension. A 3Dmore » sparse matrix solver with complex coefficients is formed for solving the resulting acoustic pressure field. The Complex Shifted Laplacian Preconditioner (CSLP) method is applied to efficiently solve the matrix system iteratively with MPI parallelization using a high performance cluster. The sound model is then coupled with the Finite Volume Community Ocean Model (FVCOM) for simulating sound propagation generated by human activities in a range-dependent setting, such as offshore wind energy platform constructions and tidal stream turbines. As a proof of concept, initial validation of the finite difference solver is presented for two coastal wedge problems. Validation of finite volume method will be reported separately.« less

Modeling of the dolphin's clicking sound source: The influence of the critical parameters

NASA Astrophysics Data System (ADS)

Dubrovsky, N. A.; Gladilin, A.; Møhl, B.; Wahlberg, M.

2004-07-01

A physical and a mathematical models of the dolphin’s source of echolocation clicks have been recently proposed. The physical model includes a bottle of pressurized air connected to the atmosphere with an underwater rubber tube. A compressing rubber ring is placed on the underwater portion of the tube. The ring blocks the air jet passing through the tube from the bottle. This ring can be brought into self-oscillation by the air jet. In the simplest case, the ring displacement follows a repeated triangular waveform. Because the acoustic pressure gradient is proportional to the second time derivative of the displacement, clicks arise at the bends of the displacement waveform. The mathematical model describes the dipole oscillations of a sphere “frozen” in the ring and calculates the waveform and the sound pressure of the generated clicks. The critical parameters of the mathematical model are the radius of the sphere and the peak value and duration of the triangular displacement curve. This model allows one to solve both the forward (deriving the properties of acoustic clicks from the known source parameters) and the inverse (calculating the source parameters from the acoustic data) problems. Data from click records of Odontocetes were used to derive both the displacement waveforms and the size of the “frozen sphere” or a structure functionally similar to it. The mathematical model predicts a maximum source level of up to 235 dB re 1 μPa at 1-m range when using a 5-cm radius of the “frozen” sphere and a 4-mm maximal displacement. The predicted sound pressure level is similar to that of the clicks produced by Odontocetest.

Digital data-acquisition system for measuring the free decay of acoustical standing waves in a resonant tube

NASA Technical Reports Server (NTRS)

Meredith, R. W.; Zuckerwar, A. J.

1984-01-01

A low-cost digital system based on an 8-bit Apple II microcomputer has been designed to provide on-line control, data acquisition, and evaluation of sound absorption measurements in gases. The measurements are conducted in a resonant tube, in which an acoustical standing wave is excited, the excitation removed, and the sound absorption evaluated from the free decay envelope. The free decay is initiated from the computer keyboard after the standing wave is established, and the microphone response signal is the source of the analog signal for the A/D converter. The acquisition software is written in ASSEMBLY language and the evaluation software in BASIC. This paper describes the acoustical measurement, hardware, software, and system performance and presents measurements of sound absorption in air as an example.

Viterbi equalization for long-distance, high-speed underwater laser communication

NASA Astrophysics Data System (ADS)

Hu, Siqi; Mi, Le; Zhou, Tianhua; Chen, Weibiao

2017-07-01

In long-distance, high-speed underwater laser communication, because of the strong absorption and scattering processes, the laser pulse is stretched with the increase in communication distance and the decrease in water clarity. The maximum communication bandwidth is limited by laser-pulse stretching. Improving the communication rate increases the intersymbol interference (ISI). To reduce the effect of ISI, the Viterbi equalization (VE) algorithm is used to estimate the maximum-likelihood receiving sequence. The Monte Carlo method is used to simulate the stretching of the received laser pulse and the maximum communication rate at a wavelength of 532 nm in Jerlov IB and Jerlov II water channels with communication distances of 80, 100, and 130 m, respectively. The high-data rate communication performance for the VE and hard-decision algorithms is compared. The simulation results show that the VE algorithm can be used to reduce the ISI by selecting the minimum error path. The trade-off between the high-data rate communication performance and minor bit-error rate performance loss makes VE a promising option for applications in long-distance, high-speed underwater laser communication systems.

Effects of nanosilver on sound absorption coefficients in solid wood species.

PubMed

Taghiyari, Hamid Reza; Esmailpour, Ayoub; Zolfaghari, Habib

2016-06-01

Sound absorption coefficients (ACs) were determined in five solid woods (poplar, beech, walnut, mulberry, and fir) in the longitudinal and tangential directions at four different frequencies of 800, 1000, 2000, and 4000 Hz. The length of the longitudinal and tangential specimens was 50-mm and 10-mm, respectively. Separate sets of specimens were impregnated with either nanosilver suspension or water. The size range of nanoparticles was 30-80 nm. Results showed that sound ACs were lower in longitudinal specimens because sound waves could penetrate the open ends of vessels more easily, being trapped and damped there. Impregnation with both nanosilver suspension and water resulted in a significant decrease in the sound ACs. The decrease in the ACs was due to the collapsing and accumulation of perforation plates and cell parts, blocking the way through which waves could pass through the vessels. This caused higher damping due to a phenomenon called vibration decay. Correlation between gas permeability versus sound AC is significantly dependant on the porous structure of individual specimens.

The sound strength parameter G and its importance in evaluating and planning the acoustics of halls for music.

PubMed

Beranek, Leo

2011-05-01

The parameter, "Strength of Sound G" is closely related to loudness. Its magnitude is dependent, inversely, on the total sound absorption in a room. By comparison, the reverberation time (RT) is both inversely related to the total sound absorption in a hall and directly related to its cubic volume. Hence, G and RT in combination are vital in planning the acoustics of a concert hall. A newly proposed "Bass Index" is related to the loudness of the bass sound and equals the value of G at 125 Hz in decibels minus its value at mid-frequencies. Listener envelopment (LEV) is shown for most halls to be directly related to the mid-frequency value of G. The broadening of sound, i.e., apparent source width (ASW) is given by degree of source broadening (DSB) which is determined from the combined effect of early lateral reflections as measured by binaural quality index (BQI) and strength G. The optimum values and limits of these parameters are discussed.

Temporal and spatial mapping of red grouper Epinephelus morio sound production.

PubMed

Wall, C C; Simard, P; Lindemuth, M; Lembke, C; Naar, D F; Hu, C; Barnes, B B; Muller-Karger, F E; Mann, D A

2014-11-01

The goals of this project were to determine the daily, seasonal and spatial patterns of red grouper Epinephelus morio sound production on the West Florida Shelf (WFS) using passive acoustics. An 11 month time series of acoustic data from fixed recorders deployed at a known E. morio aggregation site showed that E. morio produce sounds throughout the day and during all months of the year. Increased calling (number of files containing E. morio sound) was correlated to sunrise and sunset, and peaked in late summer (July and August) and early winter (November and December). Due to the ubiquitous production of sound, large-scale spatial mapping across the WFS of E. morio sound production was feasible using recordings from shorter duration-fixed location recorders and autonomous underwater vehicles (AUVs). Epinephelus morio were primarily recorded in waters 15-93 m deep, with increased sound production detected in hard bottom areas and within the Steamboat Lumps Marine Protected Area (Steamboat Lumps). AUV tracks through Steamboat Lumps, an offshore marine reserve where E. morio hole excavations have been previously mapped, showed that hydrophone-integrated AUVs could accurately map the location of soniferous fish over spatial scales of <1 km. The results show that passive acoustics is an effective, non-invasive tool to map the distribution of this species over large spatial scales. © 2014 The Fisheries Society of the British Isles.

Absorption characteristics of glass fiber materials at normal and oblique incidence. M.S. Thesis

NASA Technical Reports Server (NTRS)

Wyerman, B. R.

1974-01-01

The absorption characteristics of several fibrous materials of the Owens Corning 700 Fiberglas Series were measured to determine the variation in impedance as a function of incident angle of the sound wave. The results, indicate that the fibrous absorbents behave as extended reacting materials. The poor agreement between measurement and theory for sound absorption based on the parameters of flow resistance and porosity indicates that this theory does not adequately predict the acoustic behavior of fibrous materials. A much better agreement with measured results is obtained for values calculated from the bulk acoustic parameters of the material.

Examination of the Measurement of Absorption Using the Reverberant Room Method for Highly Absorptive Acoustic Foam

NASA Technical Reports Server (NTRS)

Hughes, William O.; McNelis, Anne M.; Chris Nottoli; Eric Wolfram

2015-01-01

The absorption coefficient for material specimens are needed to quantify the expected acoustic performance of that material in its actual usage and environment. The ASTM C423-09a standard, "Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberant Room Method" is often used to measure the absorption coefficient of material test specimens. This method has its basics in the Sabine formula. Although widely used, the interpretation of these measurements are a topic of interest. For example, in certain cases the measured Sabine absorption coefficients are greater than 1.0 for highly absorptive materials. This is often attributed to the diffraction edge effect phenomenon. An investigative test program to measure the absorption properties of highly absorbent melamine foam has been performed at the Riverbank Acoustical Laboratories. This paper will present and discuss the test results relating to the effect of the test materials' surface area, thickness and edge sealing conditions. A follow-on paper is envisioned that will present and discuss the results relating to the spacing between multiple piece specimens, and the mounting condition of the test specimen.

Sound exposure changes European seabass behaviour in a large outdoor floating pen: Effects of temporal structure and a ramp-up procedure.

PubMed

Neo, Y Y; Hubert, J; Bolle, L; Winter, H V; Ten Cate, C; Slabbekoorn, H

2016-07-01

Underwater sound from human activities may affect fish behaviour negatively and threaten the stability of fish stocks. However, some fundamental understanding is still lacking for adequate impact assessments and potential mitigation strategies. For example, little is known about the potential contribution of the temporal features of sound, the efficacy of ramp-up procedures, and the generalisability of results from indoor studies to the outdoors. Using a semi-natural set-up, we exposed European seabass in an outdoor pen to four treatments: 1) continuous sound, 2) intermittent sound with a regular repetition interval, 3) irregular repetition intervals and 4) a regular repetition interval with amplitude 'ramp-up'. Upon sound exposure, the fish increased swimming speed and depth, and swam away from the sound source. The behavioural readouts were generally consistent with earlier indoor experiments, but the changes and recovery were more variable and were not significantly influenced by sound intermittency and interval regularity. In addition, the 'ramp-up' procedure elicited immediate diving response, similar to the onset of treatment without a 'ramp-up', but the fish did not swim away from the sound source as expected. Our findings suggest that while sound impact studies outdoors increase ecological and behavioural validity, the inherently higher variability also reduces resolution that may be counteracted by increasing sample size or looking into different individual coping styles. Our results also question the efficacy of 'ramp-up' in deterring marine animals, which warrants more investigation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Compilation of Abstracts of Dissertations, Theses, and Research Papers Submitted by Candidates for Degrees

DTIC Science & Technology

1978-11-01

restricted Line Officer Financial Management Subspecialists Van Haaren, C. G., The AGOR-21 Class Oceanographic 78 LCDR, Supply Research Ships: An...Layer into a Fast Bottom Shields, R. B., Jr., Signal Enhance of Specularly 39 LT, USN Scattered Underwater Sound I MANAGEMENT - Apap, A., CDR, USN Total...Contractor Logistics 40-2 Support: A New Concept in Naval Aviation Beran, R. D, Naval Acquisition Management of 41 Weapons Center, Peculiar Ground

Turbine Sound May Influence the Metamorphosis Behaviour of Estuarine Crab Megalopae

PubMed Central

Pine, Matthew K.; Jeffs, Andrew G.; Radford, Craig A.

2012-01-01

It is now widely accepted that a shift towards renewable energy production is needed in order to avoid further anthropogenically induced climate change. The ocean provides a largely untapped source of renewable energy. As a result, harvesting electrical power from the wind and tides has sparked immense government and commercial interest but with relatively little detailed understanding of the potential environmental impacts. This study investigated how the sound emitted from an underwater tidal turbine and an offshore wind turbine would influence the settlement and metamorphosis of the pelagic larvae of estuarine brachyuran crabs which are ubiquitous in most coastal habitats. In a laboratory experiment the median time to metamorphosis (TTM) for the megalopae of the crabs Austrohelice crassa and Hemigrapsus crenulatus was significantly increased by at least 18 h when exposed to either tidal turbine or sea-based wind turbine sound, compared to silent control treatments. Contrastingly, when either species were subjected to natural habitat sound, observed median TTM decreased by approximately 21–31% compared to silent control treatments, 38–47% compared to tidal turbine sound treatments, and 46–60% compared to wind turbine sound treatments. A lack of difference in median TTM in A. crassa between two different source levels of tidal turbine sound suggests the frequency composition of turbine sound is more relevant in explaining such responses rather than sound intensity. These results show that estuarine mudflat sound mediates natural metamorphosis behaviour in two common species of estuarine crabs, and that exposure to continuous turbine sound interferes with this natural process. These results raise concerns about the potential ecological impacts of sound generated by renewable energy generation systems placed in the nearshore environment. PMID:23240063

Turbine sound may influence the metamorphosis behaviour of estuarine crab megalopae.

PubMed

Pine, Matthew K; Jeffs, Andrew G; Radford, Craig A

2012-01-01

It is now widely accepted that a shift towards renewable energy production is needed in order to avoid further anthropogenically induced climate change. The ocean provides a largely untapped source of renewable energy. As a result, harvesting electrical power from the wind and tides has sparked immense government and commercial interest but with relatively little detailed understanding of the potential environmental impacts. This study investigated how the sound emitted from an underwater tidal turbine and an offshore wind turbine would influence the settlement and metamorphosis of the pelagic larvae of estuarine brachyuran crabs which are ubiquitous in most coastal habitats. In a laboratory experiment the median time to metamorphosis (TTM) for the megalopae of the crabs Austrohelice crassa and Hemigrapsus crenulatus was significantly increased by at least 18 h when exposed to either tidal turbine or sea-based wind turbine sound, compared to silent control treatments. Contrastingly, when either species were subjected to natural habitat sound, observed median TTM decreased by approximately 21-31% compared to silent control treatments, 38-47% compared to tidal turbine sound treatments, and 46-60% compared to wind turbine sound treatments. A lack of difference in median TTM in A. crassa between two different source levels of tidal turbine sound suggests the frequency composition of turbine sound is more relevant in explaining such responses rather than sound intensity. These results show that estuarine mudflat sound mediates natural metamorphosis behaviour in two common species of estuarine crabs, and that exposure to continuous turbine sound interferes with this natural process. These results raise concerns about the potential ecological impacts of sound generated by renewable energy generation systems placed in the nearshore environment.

An analysis of sound absorbing linings for the interior of the NASA Ames 80 x 120-foot wind tunnel

NASA Technical Reports Server (NTRS)

Wilby, J. F.; White, P. H.

1985-01-01

It is desirable to achieve low frequency sound absorption in the tests section of the NASA Ames 80X120-ft wind tunnel. However, it is difficult to obtain information regarding sound absorption characteristics of potential treatments because of the restrictions placed on the dimensions of the test chambers. In the present case measurements were made in a large enclosure for aircraft ground run-up tests. The normal impedance of the acoustic treatment was measured using two microphones located close to the surface of the treatment. The data showed reasonably good agreement with analytical methods which were then used to design treatments for the wind tunnel test section. A sound-absorbing lining is proposed for the 80X120-ft wind tunnel.

A reduced-order integral formulation to account for the finite size effect of isotropic square panels using the transfer matrix method.

PubMed

Bonfiglio, Paolo; Pompoli, Francesco; Lionti, Riccardo

2016-04-01

The transfer matrix method is a well-established prediction tool for the simulation of sound transmission loss and the sound absorption coefficient of flat multilayer systems. Much research has been dedicated to enhancing the accuracy of the method by introducing a finite size effect of the structure to be simulated. The aim of this paper is to present a reduced-order integral formulation to predict radiation efficiency and radiation impedance for a panel with equal lateral dimensions. The results are presented and discussed for different materials in terms of radiation efficiency, sound transmission loss, and the sound absorption coefficient. Finally, the application of the proposed methodology for rectangular multilayer systems is also investigated and validated against experimental data.

Bubbles That Change the Speed of Sound

ERIC Educational Resources Information Center

Planinsic, Gorazd; Etkina, Eugenia

2012-01-01

The influence of bubbles on sound has long attracted the attention of physicists. In his 1920 book Sir William Bragg described sound absorption caused by foam in a glass of beer tapped by a spoon. Frank S. Crawford described and analyzed the change in the pitch of sound in a similar experiment and named the phenomenon the "hot chocolate effect."…

Developmental variation in sound production in water and air in the blue catfish Ictalurus furcatus.

PubMed

Ghahramani, Zachary N; Mohajer, Yasha; Fine, Michael L

2014-12-01

Blue catfish, Ictalurus furcatus, the largest catfish in North America, produce pectoral stridulation sounds (distress calls) when attacked and held. They have both fish and bird predators, and the frequency spectrum of their sounds is better matched to the hearing of birds than to that of unspecialized fish predators with low frequency hearing. It is unclear whether their sounds evolved to function in air or water. We categorized the calls and how they change with fish size in air and water and compared developmental changes in call parameters with stridulation motions captured with a high-speed camera. Stridulation sounds consist of a variable series of pulses produced during abduction of the pectoral spine. Pulses are caused by quick rapid spine rotations (jerks) of the pectoral spine that do not change with fish size although larger individuals generate longer, higher amplitude pulses with lower peak frequencies. There are longer pauses between jerks, and therefore fewer jerks and fewer pulses, in larger fish, which take longer to abduct their spines and therefore produce a longer series of pulses per abduction sweep. Sounds couple more effectively to water (1400 times greater pressure in Pascals at 1 m), are more sharply tuned and have lower peak frequencies than in air. Blue catfish stridulation sounds appear to be specialized to produce underwater signals although most of the sound spectrum includes frequencies matched to catfish hearing but largely above the hearing range of unspecialized fishes. © 2014. Published by The Company of Biologists Ltd.

Resonant tube for measurement of sound absorption in gases at low frequency/pressure ratios

NASA Technical Reports Server (NTRS)

Zuckerwar, A. J.; Griffin, W. A.

1980-01-01

The paper describes a resonant tube for measuring sound absorption in gases, with specific emphasis on the vibrational relaxation peak of N2, over a range of frequency/pressure ratios from 0.1 to 2500 Hz/atm. The experimental background losses measured in argon agree with the theoretical wall losses except at few isolated frequencies. Rigid cavity terminations, external excitation, and a differential technique of background evaluation were used to minimize spurious contributions to the background losses. Room temperature measurements of sound absorption in binary mixtures of N2-CO2 in which both components are excitable resulted in the maximum frequency/pressure ratio in Hz/atm of 0.063 + 123m for the N2 vibrational relaxation peak, where m is mole percent of added CO2; the maximum ratio for the CO2 peak was 34,500 268m where m is mole percent of added N2.

Sound absorption enhancement of nonwoven felt by using coupled membrane - sonic crystal inclusion

NASA Astrophysics Data System (ADS)

Fitriani, M. C.; Yahya, I.; Harjana; Ubaidillah; Aditya, F.; Siregar, Y.; Moeliono, M.; Sulaksono, S.

2016-11-01

The experimental results from laboratory test on the sound absorption performance of nonwoven felt with an array thin tubes and sonic crystal inclusions reported in this paper. The nonwoven felt sample was produced by a local company with 15 mm in its thickness and 900 gsm. The 6.4 mm diameter plastic straw was used to construct the thin tubes array while the sonic crystal is arranged in a 4 × 4 lattice crystal formation. It made from a PVC cylinder with 17 mm and 50 mm in diameter and length respectively. All cylinders have two holes positioned on 10 mm and 25 mm from the base. The results show that both treatments, array of thin tube and sonic crystal inclusions are effectively increased the sound absorption coefficient of the nonwoven felt significantly especially in the low frequency range starting from 200Hz.

Spatial avoidance to experimental increase of intermittent and continuous sound in two captive harbour porpoises.

PubMed

Kok, Annebelle C M; Engelberts, J Pamela; Kastelein, Ronald A; Helder-Hoek, Lean; Van de Voorde, Shirley; Visser, Fleur; Slabbekoorn, Hans

2018-02-01

The continuing rise in underwater sound levels in the oceans leads to disturbance of marine life. It is thought that one of the main impacts of sound exposure is the alteration of foraging behaviour of marine species, for example by deterring animals from a prey location, or by distracting them while they are trying to catch prey. So far, only limited knowledge is available on both mechanisms in the same species. The harbour porpoise (Phocoena phocoena) is a relatively small marine mammal that could quickly suffer fitness consequences from a reduction of foraging success. To investigate effects of anthropogenic sound on their foraging efficiency, we tested whether experimentally elevated sound levels would deter two captive harbour porpoises from a noisy pool into a quiet pool (Experiment 1) and reduce their prey-search performance, measured as prey-search time in the noisy pool (Experiment 2). Furthermore, we tested the influence of the temporal structure and amplitude of the sound on the avoidance response of both animals. Both individuals avoided the pool with elevated sound levels, but they did not show a change in search time for prey when trying to find a fish hidden in one of three cages. The combination of temporal structure and SPL caused variable patterns. When the sound was intermittent, increased SPL caused increased avoidance times. When the sound was continuous, avoidance was equal for all SPLs above a threshold of 100 dB re 1 μPa. Hence, we found no evidence for an effect of sound exposure on search efficiency, but sounds of different temporal patterns did cause spatial avoidance with distinct dose-response patterns. Copyright © 2017 Elsevier Ltd. All rights reserved.

Temporary shift in masked hearing thresholds in odontocetes after exposure to single underwater impulses from a seismic watergun.

PubMed

Finneran, James J; Schlundt, Carolyn E; Dear, Randall; Carder, Donald A; Ridgway, Sam H

2002-06-01

A behavioral response paradigm was used to measure masked underwater hearing thresholds in a bottlenose dolphin (Tursiops truncatus) and a white whale (Delphinapterus leucas) before and after exposure to single underwater impulsive sounds produced from a seismic watergun. Pre- and postexposure thresholds were compared to determine if a temporary shift in masked hearing thresholds (MTTS), defined as a 6-dB or larger increase in postexposure thresholds, occurred. Hearing thresholds were measured at 0.4, 4, and 30 kHz. MTTSs of 7 and 6 dB were observed in the white whale at 0.4 and 30 kHz, respectively, approximately 2 min following exposure to single impulses with peak pressures of 160 kPa, peak-to-peak pressures of 226 dB re 1 microPa, and total energy fluxes of 186 dB re 1 microPa2 x s. Thresholds returned to within 2 dB of the preexposure value approximately 4 min after exposure. No MTTS was observed in the dolphin at the highest exposure conditions: 207 kPa peak pressure, 228 dB re 1 microPa peak-to-peak pressure, and 188 dB re 1 microPa2 x s total energy flux.

Potential implications of acoustic stimuli as a non-physical barrier to silver carp and bighead carp

USGS Publications Warehouse

Murchy, Kelsie; Cupp, Aaron R.; Amberg, Jon J.; Vetter, Brooke J.; Fredricks, Kim; Gaikowski, Mark; Mensinger, Allen F.

2017-01-01

The effectiveness of an acoustic barrier to deter the movement of silver carp, Hypophthalmichthys molitrix (Valenciennes) and bighead carp, H. nobilis (Richardson) was evaluated. A pond (10 m × 5 m × 1.2 m) was divided in half by a concrete-block barrier with a channel (1 m across) allowing fish access to each side. Underwater speakers were placed on each side of the barrier opening, and an outboard motor noise (broadband sound; 0.06–10 kHz) was broadcast to repel carp that approached within 1 m of the channel. Broadband sound was effective at reducing the number of successful crossings in schools of silver carp, bighead carp and a combined school. Repulsion rates were 82.5% (silver carp), 93.7% (bighead carp) and 90.5% (combined). This study demonstrates that broadband sound is effective in deterring carp and could be used as a deterrent in an integrated pest management system.

Needs Assessment and Scoping Study for Sinking Ships as Diving Sites in Puget Sound

USGS Publications Warehouse

Rubin, Steve; Grossman, Eric E.; Koontz, Lynne; Paulson, Anthony; Sexton, Natalie; Reisenbichler, Reg

2008-01-01

BACKGROUND There is growing interest in starting a program to sink ships in Puget Sound to create one or more underwater dive sites. Experience in other parts of the world has indicated that sunken vessels are highly popular with divers and could provide a basis for increased recreation and attraction of out-of-state divers with attendant economic benefits to the State. The Washington State legislature reviewed this possibility during the 2006 session and determined that more information is required before the legislature could determine if this activity is feasible or desirable. The legislature directed several State agencies to undertake a preliminary study of the feasibility. The Washington Department of Fish and Wildlife (WDFW, lead State agency) in turn asked U.S. Geological Survey to conduct the study.

Harnessing Multiple Internal Reflections to Design Highly Absorptive Acoustic Metasurfaces

NASA Astrophysics Data System (ADS)

Shen, Chen; Cummer, Steven A.

2018-05-01

The rapid development of metasurfaces has enabled numerous intriguing applications with acoustically thin sheets. Here we report the theory and experimental realization of a nonresonant sound-absorbing strategy using metasurfaces by harnessing multiple internal reflections. We theoretically and numerically show that the higher-order diffraction of thin gradient-index metasurfaces is tied to multiple internal reflections inside the unit cells. Highly absorbing acoustic metasurfaces can be realized by enforcing multiple internal reflections together with a small amount of loss. A reflective gradient-index acoustic metasurface is designed based on the theory, and we further experimentally verify the performance using a three-dimensional printed prototype. Measurements show over 99% energy absorption at the peak frequency and a 95% energy absorption bandwidth of around 600 Hz. The proposed mechanism provides an alternative route for sound absorption without the necessity of high absorption of the individual unit cells.

The Influence of Climate Change on the Intensity of Ice Gouging of the Bottom by Hummocky Formations

NASA Astrophysics Data System (ADS)

Ogorodov, S. A.; Arkhipov, V. V.; Baranskaya, A. V.; Kokin, O. V.; Romanov, A. O.

2018-02-01

In the present work, several results of repeated sounding of bottom ice gouging microrelief within the area of the underwater pipeline crossing of the Baydaratskaya Bay, Kara Sea, are presented. Based on the results of the monitoring, as well as the analysis of literature sources and modeling it has been established that under the conditions of climate warming and sea ice reduction, the zone of the most intensive ice gouging is shifted landwards, on shallower water areas.

Initial Phase of a Study of Bottom Interaction of Low Frequency Underwater Sound

DTIC Science & Technology

1976-04-06

groups. The people involved include Halcyon Morris, Homer Bucker, Ed Hamilton, and Mel Pederson of the Naval Undersea Center, San Diego, California...0> > I. * I ’ . A R ’.~ o ’~ A .~ 0IA0 -47 I- I LL I 4 ~ 4C< a... UU N 0l0 ~~0w I,: U E 4= . RL UTa, e g - - 8a 7 58 o _ _ _L J. 0 I A -I L)-J z ED

Bubbles

NASA Astrophysics Data System (ADS)

Prosperetti, Andrea

2004-06-01

Vanitas vanitatum et omnia vanitas: bubbles are emptiness, non-liquid, a tiny cloud shielding a mathematical singularity. Born from chance, a violent and brief life ending in the union with the (nearly) infinite. But a wealth of phenomena spring forth from this nothingness: underwater noise, sonoluminescence, boiling, and many others. Some recent results on a "blinking bubble" micropump and vapor bubbles in sound fields are outlined. The last section describes Leonardo da Vinci's observation of the non-rectlinear ascent of buoyant bubbles and justifies the name Leonardo's paradox recently attributed to this phenomenon.

The Canadian Diving Symposium (2nd) Held at Defence and Civil Institute of Environmental Medicine, 31 October - 1 November 1977.

DTIC Science & Technology

1977-11-01

in oceanography, marine sL veying and marine engineering. The elective subjects cover such topics as hydrographic sur- veying, sounding , underwater...and Diving in Mr. J. Tomlinson D.F.E. Department of Fisheries and Marine Services L.Portable System for Ultrasonic Mr. B. EAtock, DCIEM Doppler...semi-tropical and temperate environments (1). As with all homeothermic mammals , the human body has a deep internal temperattre of approximately 37 0

Predicting the Underwater Sound of Moderate and Heavy Rainfall from Laboratory Measurements of Radiation from Single Large Raindrops

DTIC Science & Technology

1992-03-01

Elementary Linear Algebra with Applications, pp. 301- 323, John Wiley and Sons Inc., 1987. Atlas, D., and Ulbrich, C. E. W., "The Physical Basis for...vector drd In this case, the linear system is said to be inconsistent ( Anton and Rorres, 1987). In contrast, for an underdetermined system (where the...ocean acoustical tomography and seismology. In simplest terms, the general linear inverse problem consists of fimding the desired solution to a set of m

Study of the Acoustic Effects of Hydrokinetic Tidal Turbines in Admiralty Inlet, Puget Sound

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brian Polagye; Jim Thomson; Chris Bassett

2012-03-30

Hydrokinetic turbines will be a source of noise in the marine environment - both during operation and during installation/removal. High intensity sound can cause injury or behavioral changes in marine mammals and may also affect fish and invertebrates. These noise effects are, however, highly dependent on the individual marine animals; the intensity, frequency, and duration of the sound; and context in which the sound is received. In other words, production of sound is a necessary, but not sufficient, condition for an environmental impact. At a workshop on the environmental effects of tidal energy development, experts identified sound produced by turbinesmore » as an area of potentially significant impact, but also high uncertainty. The overall objectives of this project are to improve our understanding of the potential acoustic effects of tidal turbines by: (1) Characterizing sources of existing underwater noise; (2) Assessing the effectiveness of monitoring technologies to characterize underwater noise and marine mammal responsiveness to noise; (3) Evaluating the sound profile of an operating tidal turbine; and (4) Studying the effect of turbine sound on surrogate species in a laboratory environment. This study focuses on a specific case study for tidal energy development in Admiralty Inlet, Puget Sound, Washington (USA), but the methodologies and results are applicable to other turbine technologies and geographic locations. The project succeeded in achieving the above objectives and, in doing so, substantially contributed to the body of knowledge around the acoustic effects of tidal energy development in several ways: (1) Through collection of data from Admiralty Inlet, established the sources of sound generated by strong currents (mobilizations of sediment and gravel) and determined that low-frequency sound recorded during periods of strong currents is non-propagating pseudo-sound. This helped to advance the debate within the marine and hydrokinetics acoustic community as to whether strong currents produce propagating sound. (2) Analyzed data collected from a tidal turbine operating at the European Marine Energy Center to develop a profile of turbine sound and developed a framework to evaluate the acoustic effects of deploying similar devices in other locations. This framework has been applied to Public Utility District No. 1 of Snohomish Country's demonstration project in Admiralty Inlet to inform postinstallation acoustic and marine mammal monitoring plans. (3) Demonstrated passive acoustic techniques to characterize the ambient noise environment at tidal energy sites (fixed, long-term observations recommended) and characterize the sound from anthropogenic sources (drifting, short-term observations recommended). (4) Demonstrated the utility and limitations of instrumentation, including bottom mounted instrumentation packages, infrared cameras, and vessel monitoring systems. In doing so, also demonstrated how this type of comprehensive information is needed to interpret observations from each instrument (e.g., hydrophone data can be combined with vessel tracking data to evaluate the contribution of vessel sound to ambient noise). (5) Conducted a study that suggests harbor porpoise in Admiralty Inlet may be habituated to high levels of ambient noise due to omnipresent vessel traffic. The inability to detect behavioral changes associated with a high intensity source of opportunity (passenger ferry) has informed the approach for post-installation marine mammal monitoring. (6) Conducted laboratory exposure experiments of juvenile Chinook salmon and showed that exposure to a worse than worst case acoustic dose of turbine sound does not result in changes to hearing thresholds or biologically significant tissue damage. Collectively, this means that Chinook salmon may be at a relatively low risk of injury from sound produced by tidal turbines located in or near their migration path. In achieving these accomplishments, the project has significantly advanced the District's goals of developing a demonstration-scale tidal energy project in Admiralty Inlet. Pilot demonstrations of this type are an essential step in the development of commercial-scale tidal energy in the United States. This is a renewable resource capable of producing electricity in a highly predictable manner.« less

Enhancing sound absorption and transmission through flexible multi-layer micro-perforated structures.

PubMed

Bravo, Teresa; Maury, Cédric; Pinhède, Cédric

2013-11-01

Theoretical and experimental results are presented into the sound absorption and transmission properties of multi-layer structures made up of thin micro-perforated panels (ML-MPPs). The objective is to improve both the absorption and insulation performances of ML-MPPs through impedance boundary optimization. A fully coupled modal formulation is introduced that predicts the effect of the structural resonances onto the normal incidence absorption coefficient and transmission loss of ML-MPPs. This model is assessed against standing wave tube measurements and simulations based on impedance translation method for two double-layer MPP configurations of relevance in building acoustics and aeronautics. Optimal impedance relationships are proposed that ensure simultaneous maximization of both the absorption and the transmission loss under normal incidence. Exhaustive optimization of the double-layer MPPs is performed to assess the absorption and/or transmission performances with respect to the impedance criterion. It is investigated how the panel volumetric resonances modify the excess dissipation that can be achieved from non-modal optimization of ML-MPPs.

The effect of a periodic absorptive strip arrangement on an interior sound field in a room.

PubMed

Park, Joo-Bae; Grosh, Karl; Kim, Yang-Hann

2005-02-01

In this paper we study the effect of periodically arranged sound absorptive strips on the mean acoustic potential energy density distribution of a room. The strips are assumed to be attached on the room's surface of interest. In order to determine their effect, the mean acoustic potential energy density variation is evaluated as the function of a ratio of the strip's arrangement period to wavelength. The evaluation demonstrates that the mean acoustic potential energy density tends to converge. In addition, a comparison with a case in which absorptive materials completely cover the selected absorptive plane shows that a periodic arrangement that uses only half of the absorptive material can be more efficient than a total covering, unless the frequency of interest does not coincide with the room's resonant frequencies. Consequently, the results prove that the ratio of the arrangement period to the wavelength plays an important role in the effectiveness of a periodic absorptive strip arrangement to minimize a room's mean acoustic potential energy density.

Highly efficient special sound absorbing solutions

NASA Technical Reports Server (NTRS)

Ionescu, M.; Petre-Lazar, S.

1974-01-01

Highly efficient special sound absorbing structures with the following criteria are considered: (1) A distribution surface of the sound absorbing material greater than that of the building element on which the structure is placed; (2) The highest possible absorption coefficient in the widest possible frequency band; and (3) adaptability to different construction and aesthetic conditions.

Sound propagation in street canyons: comparison between diffusely and geometrically reflecting boundaries

PubMed

Kang

2000-03-01

This paper systematically compares the sound fields in street canyons with diffusely and geometrically reflecting boundaries. For diffuse boundaries, a radiosity-based theoretical/computer model has been developed. For geometrical boundaries, the image source method has been used. Computations using the models show that there are considerable differences between the sound fields resulting from the two kinds of boundaries. By replacing diffuse boundaries with geometrical boundaries, the sound attenuation along the length becomes significantly less; the RT30 is considerably longer; and the extra attenuation caused by air or vegetation absorption is reduced. There are also some similarities between the sound fields under the two boundary conditions. For example, in both cases the sound attenuation along the length with a given amount of absorption is the highest if the absorbers are arranged on one boundary and the lowest if they are evenly distributed on all boundaries. Overall, the results suggest that, from the viewpoint of urban noise reduction, it is better to design the street boundaries as diffusely reflective rather than acoustically smooth.

Photoacoustics and speed-of-sound dual mode imaging with a long depth-of-field by using annular ultrasound array.

PubMed

Ding, Qiuning; Tao, Chao; Liu, Xiaojun

2017-03-20

Speed-of-sound and optical absorption reflect the structure and function of tissues from different aspects. A dual-mode microscopy system based on a concentric annular ultrasound array is proposed to simultaneously acquire the long depth-of-field images of speed-of-sound and optical absorption of inhomogeneous samples. First, speed-of-sound is decoded from the signal delay between each element of the annular array. The measured speed-of-sound could not only be used as an image contrast, but also improve the resolution and accuracy of spatial location of photoacoustic image in inhomogeneous acoustic media. Secondly, benefitting from dynamic focusing of annular array and the measured speed-of-sound, it is achieved an advanced acoustic-resolution photoacoustic microscopy with a precise position and a long depth-of-field. The performance of the dual-mode imaging system has been experimentally examined by using a custom-made annular array. The proposed dual-mode microscopy might have the significances in monitoring the biological physiological and pathological processes.

Problems in Assessment of the UV Penetration into Natural Waters from Space-based Measurements

NASA Technical Reports Server (NTRS)

Vasilkov, Alexander P.; Herman, Jay; Krotkov, Nickolay A.; Kahru, Mati; Mitchell, B. Greg; Hsu, Christina; Bhartia, P. K. (Technical Monitor)

2002-01-01

Satellite instruments currently provide global maps of surface UV (ultraviolet) irradiance by combining backscattered radiance data with radiative transfer models. The models are often limited by uncertainties in physical input parameters of the atmosphere and surface. Global mapping of the underwater UV irradiance creates further challenges for the models. The uncertainties in physical input parameters become more serious because of the presence of absorbing and scattering quantities caused by biological processes within the oceans. In this paper we summarize the problems encountered in the assessment of the underwater UV irradiance from space-based measurements, and propose approaches to resolve the problems. We have developed a radiative transfer scheme for computation of the UV irradiance in the atmosphere-ocean system. The scheme makes use of input parameters derived from satellite instruments such as TOMS (Total Ozone Mapping Spectrometer) and SeaWiFS (Sea-viewing Wide Field-of-view Sensor). The major problem in assessment of the surface UV irradiance is to accurately quantify the effects of clouds. Unlike the standard TOMS UV algorithm, we use the cloud fraction products available from SeaWiFS and MODIS (Moderate Resolution Imaging Spectrometer) to calculate instantaneous surface flux at the ocean surface. Daily UV doses can be calculated by assuming a model of constant cloudiness throughout the day. Both SeaWiFS and MODIS provide some estimates of seawater optical properties in the visible. To calculate the underwater UV flux the seawater optical properties must be extrapolated down to shorter wavelengths. Currently, the problem of accurate extrapolation of visible data down to the UV spectral range is not solved completely, and there are few available measurements. The major difficulty is insufficient correlation between photosynthetic and photoprotective pigments of phytoplankton absorbing in the visible and UV respectively. We propose to empirically parameterize seawater absorption in the UV on a basis of available data sets of bio-optical measurements from a variety of ocean waters. Another problem is the lack of reliable data on pure seawater absorption in the UV. Laboratory measurements of the UV absorption of both pure water and pure seawater are required.

Sounds and source levels from bowhead whales off Pt. Barrow, Alaska.

PubMed

Cummings, W C; Holliday, D V

1987-09-01

Sounds were recorded from bowhead whales migrating past Pt. Barrow, AK, to the Canadian Beaufort Sea. They mainly consisted of various low-frequency (25- to 900-Hz) moans and well-defined sound sequences organized into "song" (20-5000 Hz) recorded with our 2.46-km hydrophone array suspended from the ice. Songs were composed of up to 20 repeated phrases (mean, 10) which lasted up to 146 s (mean, 66.3). Several bowhead whales often were within acoustic range of the array at once, but usually only one sang at a time. Vocalizations exhibited diurnal peaks of occurrence (0600-0800, 1600-1800 h). Sounds which were located in the horizontal plane had peak source spectrum levels as follows--44 moans: 129-178 dB re: 1 microPa, 1 m (median, 159); 3 garglelike utterances: 152, 155, and 169 dB; 33 songs: 158-189 dB (median, 177), all presumably from different whales. Based on ambient noise levels, measured total propagation loss, and whale sound source levels, our detection of whale sounds was theoretically noise-limited beyond 2.5 km (moans) and beyond 10.7 km (songs), a model supported by actual localizations. This study showed that over much of the shallow Arctic and sub-Arctic waters, underwater communications of the bowhead whale would be limited to much shorter ranges than for other large whales in lower latitude, deep-water regions.

Potential impacts of shipping noise on Indo-Pacific humpback dolphins and implications for regulation and mitigation: a review.

PubMed

Li, Songhai; Liu, Mingming; Dong, Lijun; Dong, Jianchen; Wang, Ding

2018-01-09

Shipping noise is a widespread and relatively loud sound source among human-induced underwater sounds. The impacts of shipping noise are of special concern for Indo-Pacific humpback dolphins (Sousa chinensis), as they inhabit shallow and nearshore habitats and are highly dependent on sound for survival. This study synthesizes our current understanding of the potential impacts of shipping noise on Indo-Pacific humpback dolphins combined with knowledge on sound production and hearing of these animals and the impacts of noise on other whales and dolphins. For further protection and management of Indo-Pacific humpback dolphins and their habitats, shipping noise should be regulated and mitigated to modify sound from ships, to reduce overall noise levels, and to set more marine protected areas (MPAs) covering most Indo-Pacific humpback dolphin habitats with seasonal and geographical restrictions to avoid ensonification of shipping noise. The emphasis for future research should be on obtaining more baseline information about the population distribution, sound production, hearing capabilities at the population level, behavior, and stress hormones of the humpback dolphins under different noise conditions or under different noise-producing activities, and/or in high-noise areas compared with relatively quiet areas, and the noise characteristics of ships of different types, sizes, and speeds. This article is protected by copyright. All rights reserved.

Early Development and Orientation of the Acoustic Funnel Provides Insight into the Evolution of Sound Reception Pathways in Cetaceans

PubMed Central

Yamato, Maya; Pyenson, Nicholas D.

2015-01-01

Whales receive underwater sounds through a fundamentally different mechanism than their close terrestrial relatives. Instead of hearing through the ear canal, cetaceans hear through specialized fatty tissues leading to an evolutionarily novel feature: an acoustic funnel located anterior to the tympanic aperture. We traced the ontogenetic development of this feature in 56 fetal specimens from 10 different families of toothed (odontocete) and baleen (mysticete) whales, using X-ray computed tomography. We also charted ear ossification patterns through ontogeny to understand the impact of heterochronic developmental processes. We determined that the acoustic funnel arises from a prominent V-shaped structure established early in ontogeny, formed by the malleus and the goniale. In odontocetes, this V-formation develops into a cone-shaped funnel facing anteriorly, directly into intramandibular acoustic fats, which is likely functionally linked to the anterior orientation of sound reception in echolocation. In contrast, the acoustic funnel in balaenopterids rotates laterally, later in fetal development, consistent with a lateral sound reception pathway. Balaenids and several fossil mysticetes retain a somewhat anteriorly oriented acoustic funnel in the mature condition, indicating that a lateral sound reception pathway in balaenopterids may be a recent evolutionary innovation linked to specialized feeding modes, such as lunge-feeding. PMID:25760328

Low-frequency sound speed and attenuation in sandy seabottom from long-range broadband acoustic measurements.

PubMed

Wan, Lin; Zhou, Ji-Xun; Rogers, Peter H

2010-08-01

A joint China-U.S. underwater acoustics experiment was conducted in the Yellow Sea with a very flat bottom and a strong and sharp thermocline. Broadband explosive sources were deployed both above and below the thermocline along two radial lines up to 57.2 km and a quarter circle with a radius of 34 km. Two inversion schemes are used to obtain the seabottom sound speed. One is based on extracting normal mode depth functions from the cross-spectral density matrix. The other is based on the best match between the calculated and measured modal arrival times for different frequencies. The inverted seabottom sound speed is used as a constraint condition to extract the seabottom sound attenuation by three methods. The first method involves measuring the attenuation coefficients of normal modes. In the second method, the seabottom sound attenuation is estimated by minimizing the difference between the theoretical and measured modal amplitude ratios. The third method is based on finding the best match between the measured and modeled transmission losses (TLs). The resultant seabottom attenuation, averaged over three independent methods, can be expressed as alpha=(0.33+/-0.02)f(1.86+/-0.04)(dB/m kHz) over a frequency range of 80-1000 Hz.

The Auditory Anatomy of the Minke Whale (Balaenoptera acutorostrata): A Potential Fatty Sound Reception Pathway in a Baleen Whale

PubMed Central

Yamato, Maya; Ketten, Darlene R; Arruda, Julie; Cramer, Scott; Moore, Kathleen

2012-01-01

Cetaceans possess highly derived auditory systems adapted for underwater hearing. Odontoceti (toothed whales) are thought to receive sound through specialized fat bodies that contact the tympanoperiotic complex, the bones housing the middle and inner ears. However, sound reception pathways remain unknown in Mysticeti (baleen whales), which have very different cranial anatomies compared to odontocetes. Here, we report a potential fatty sound reception pathway in the minke whale (Balaenoptera acutorostrata), a mysticete of the balaenopterid family. The cephalic anatomy of seven minke whales was investigated using computerized tomography and magnetic resonance imaging, verified through dissections. Findings include a large, well-formed fat body lateral, dorsal, and posterior to the mandibular ramus and lateral to the tympanoperiotic complex. This fat body inserts into the tympanoperiotic complex at the lateral aperture between the tympanic and periotic bones and is in contact with the ossicles. There is also a second, smaller body of fat found within the tympanic bone, which contacts the ossicles as well. This is the first analysis of these fatty tissues' association with the auditory structures in a mysticete, providing anatomical evidence that fatty sound reception pathways may not be a unique feature of odontocete cetaceans. Anat Rec, 2012. © 2012 Wiley Periodicals, Inc. PMID:22488847

Evidence of Cnidarians sensitivity to sound after exposure to low frequency noise underwater sources

NASA Astrophysics Data System (ADS)

Solé, Marta; Lenoir, Marc; Fontuño, José Manuel; Durfort, Mercè; van der Schaar, Mike; André, Michel

2016-12-01

Jellyfishes represent a group of species that play an important role in oceans, particularly as a food source for different taxa and as a predator of fish larvae and planktonic prey. The massive introduction of artificial sound sources in the oceans has become a concern to science and society. While we are only beginning to understand that non-hearing specialists like cephalopods can be affected by anthropogenic noises and regulation is underway to measure European water noise levels, we still don’t know yet if the impact of sound may be extended to other lower level taxa of the food web. Here we exposed two species of Mediterranean Scyphozoan medusa, Cotylorhiza tuberculata and Rhizostoma pulmo to a sweep of low frequency sounds. Scanning electron microscopy (SEM) revealed injuries in the statocyst sensory epithelium of both species after exposure to sound, that are consistent with the manifestation of a massive acoustic trauma observed in other species. The presence of acoustic trauma in marine species that are not hearing specialists, like medusa, shows the magnitude of the problem of noise pollution and the complexity of the task to determine threshold values that would help building up regulation to prevent permanent damage of the ecosystems.

Laser induced fluorescence of dental caries

NASA Technical Reports Server (NTRS)

Albin, S.; Byvik, C. E.; Buoncristiani, A. M.

1988-01-01

Significant differences between the optical spectra taken from sound regions of teeth and carious regions have been observed. These differences appear both in absorption and in laser induced fluorescence spectra. Excitation by the 488 nm line of an argon ion laser beam showed a peak in the emission intensity around 553 nm for the sound dental material while the emission peak from the carious region was red-shifted by approximately 40 nm. The relative absorption of carious region was significantly higher at 488 nm; however its fluorescence intensity peak was lower by an order of magnitude compared to the sound tooth. Implications of these results for a safe, reliable and early detection of dental caries are discussed.

Optimization of the acoustic absorption coefficients of certain functional absorbents

NASA Technical Reports Server (NTRS)

Pocsa, V.; Biborosch, L.; Veres, A.; Halpert, E.; Lorian, R.; Botos, T.

1974-01-01

The sound absorption coefficients of some functional absorbents (mineral wool plates) are determined by the reverberation chamber method. The influence of the angle of inclination of the sound absorbing material with respect to the surface to be treated is analyzed as well as the influence of the covering index, defined as the ratio of the designed area of a plate and the area of the treated surface belonging to another plate. As compared with the conventional method of applying sound-absorbing plates, the analyzed structures have a higher technological and economical efficiency. The optimum structure corresponds to an angle of inclination of 15 deg and a covering index of 0.8.

Temporal and Spatial Comparisons of Underwater Sound Signatures of Different Reef Habitats in Moorea Island, French Polynesia.

PubMed

Bertucci, Frédéric; Parmentier, Eric; Berten, Laëtitia; Brooker, Rohan M; Lecchini, David

2015-01-01

As environmental sounds are used by larval fish and crustaceans to locate and orientate towards habitat during settlement, variations in the acoustic signature produced by habitats could provide valuable information about habitat quality, helping larvae to differentiate between potential settlement sites. However, very little is known about how acoustic signatures differ between proximate habitats. This study described within- and between-site differences in the sound spectra of five contiguous habitats at Moorea Island, French Polynesia: the inner reef crest, the barrier reef, the fringing reef, a pass and a coastal mangrove forest. Habitats with coral (inner, barrier and fringing reefs) were characterized by a similar sound spectrum with average intensities ranging from 70 to 78 dB re 1 μPa.Hz(-1). The mangrove forest had a lower sound intensity of 70 dB re 1 μPa.Hz(-1) while the pass was characterized by a higher sound level with an average intensity of 91 dB re 1 μPa.Hz(-1). Habitats showed significantly different intensities for most frequencies, and a decreasing intensity gradient was observed from the reef to the shore. While habitats close to the shore showed no significant diel variation in sound intensities, sound levels increased at the pass during the night and barrier reef during the day. These two habitats also appeared to be louder in the North than in the West. These findings suggest that daily variations in sound intensity and across-reef sound gradients could be a valuable source of information for settling larvae. They also provide further evidence that closely related habitats, separated by less than 1 km, can differ significantly in their spectral composition and that these signatures might be typical and conserved along the coast of Moorea.

Impacts of distinct observations during the 2009 Prince William Sound field experiment: A data assimilation study

NASA Astrophysics Data System (ADS)

Li, Z.; Chao, Y.; Farrara, J.; McWilliams, J. C.

2012-12-01

A set of data assimilation experiments, known as Observing System Experiments (OSEs), are performed to assess the relative impacts of different types of observations acquired during the 2009 Prince William Sound Field Experiment. The observations assimilated consist primarily of three types: High Frequency (HF) radar surface velocities, vertical profiles of temperature/salinity (T/S) measured by ships, moorings, Autonomous Underwater Vehicles and gliders, and satellite sea surface temperatures (SSTs). The impact of all the observations, HF radar surface velocities, and T/S profiles is assessed. Without data assimilation, a frequently occurring cyclonic eddy in the central Sound is overly persistent and intense. The assimilation of the HF radar velocities effectively reduces these biases and improves the representation of the velocities as well as the T/S fields in the Sound. The assimilation of the T/S profiles improves the large scale representation of the temperature/salinity and also the velocity field in the central Sound. The combination of the HF radar surface velocities and sparse T/S profiles results in an observing system capable of representing the circulation in the Sound reliably and thus producing analyses and forecasts with useful skill. It is suggested that a potentially promising observing network could be based on satellite SSHs and SSTs along with sparse T/S profiles, and future satellite SSHs with wide swath coverage and higher resolution may offer excellent data that will be of great use for predicting the circulation in the Sound.

Hybrid waste filler filled bio-polymer foam composites for sound absorbent materials

NASA Astrophysics Data System (ADS)

Rus, Anika Zafiah M.; Azahari, M. Shafiq M.; Kormin, Shaharuddin; Soon, Leong Bong; Zaliran, M. Taufiq; Ahraz Sadrina M. F., L.

2017-09-01

Sound absorption materials are one of the major requirements in many industries with regards to the sound insulation developed should be efficient to reduce sound. This is also important to contribute in economically ways of producing sound absorbing materials which is cheaper and user friendly. Thus, in this research, the sound absorbent properties of bio-polymer foam filled with hybrid fillers of wood dust and waste tire rubber has been investigated. Waste cooking oil from crisp industries was converted into bio-monomer, filled with different proportion ratio of fillers and fabricated into bio-polymer foam composite. Two fabrication methods is applied which is the Close Mold Method (CMM) and Open Mold Method (OMM). A total of four bio-polymer foam composite samples were produce for each method used. The percentage of hybrid fillers; mixture of wood dust and waste tire rubber of 2.5 %, 5.0%, 7.5% and 10% weight to weight ration with bio-monomer. The sound absorption of the bio-polymer foam composites samples were tested by using the impedance tube test according to the ASTM E-1050 and Scanning Electron Microscope to determine the morphology and porosity of the samples. The sound absorption coefficient (α) at different frequency range revealed that the polymer foam of 10.0 % hybrid fillers shows highest α of 0.963. The highest hybrid filler loading contributing to smallest pore sizes but highest interconnected pores. This also revealed that when highly porous material is exposed to incident sound waves, the air molecules at the surface of the material and within the pores of the material are forced to vibrate and loses some of their original energy. This is concluded that the suitability of bio-polymer foam filled with hybrid fillers to be used in acoustic application of automotive components such as dashboards, door panels, cushion and etc.

Atmospheric absorption of sound - Update

NASA Technical Reports Server (NTRS)

Bass, H. E.; Sutherland, L. C.; Zuckerwar, A. J.

1990-01-01

Best current expressions for the vibrational relaxation times of oxygen and nitrogen in the atmosphere are used to compute total absorption. The resulting graphs of total absorption as a function of frequency for different humidities should be used in lieu of the graph published earlier by Evans et al (1972).

Analytical coupled modeling of a magneto-based acoustic metamaterial harvester

NASA Astrophysics Data System (ADS)

Nguyen, H.; Zhu, R.; Chen, J. K.; Tracy, S. L.; Huang, G. L.

2018-05-01

Membrane-type acoustic metamaterials (MAMs) have demonstrated unusual capacity in controlling low-frequency sound transmission, reflection, and absorption. In this paper, an analytical vibro-acoustic-electromagnetic coupling model is developed to study MAM harvester sound absorption, energy conversion, and energy harvesting behavior under a normal sound incidence. The MAM harvester is composed of a prestressed membrane with an attached rigid mass, a magnet coil, and a permanent magnet coin. To accurately capture finite-dimension rigid mass effects on the membrane deformation under the variable magnet force, a theoretical model based on the deviating acoustic surface Green’s function approach is developed by considering the acoustic near field and distributed effective shear force along the interfacial boundary between the mass and the membrane. The accuracy and capability of the theoretical model is verified through comparison with the finite element method. In particular, sound absorption, acoustic-electric energy conversion, and harvesting coefficient are quantitatively investigated by varying the weight and size of the attached mass, prestress and thickness of the membrane. It is found that the highest achievable conversion and harvesting coefficients can reach up to 48%, and 36%, respectively. The developed model can serve as an efficient tool for designing MAM harvesters.

Analysis of absorption and reflection mechanisms in a three-dimensional plate silencer

NASA Astrophysics Data System (ADS)

Wang, Chunqi; Huang, Lixi

2008-06-01

When a segment of a rigid duct is replaced by a plate backed by a hard-walled cavity, grazing incident sound waves induce plate vibration, hence sound reflection. Based on this mechanism, a broadband plate silencer, which works effectively from low-to-medium frequencies have been developed recently. A typical plate silencer consists of an expansion chamber with two side-branch cavities covered by light but extremely stiff plates. Such a configuration is two-dimensional in nature. In this paper, numerical study is extended to three-dimensional configurations to investigate the potential improvement in sound reflection. Finite element simulation shows that the three-dimensional configurations perform better than the corresponding two-dimensional design, especially in the relatively high frequency region. Further analysis shows that the three-dimensional design gives better plate response at higher axial modes than the simple two-dimensional design. Sound absorption mechanism is also introduced to the plate silencer by adding two dissipative chambers on the two lateral sides of a two-cavity wave reflector, hence a hybrid silencer. Numerical simulation shows that the proposed hybrid silencer is able to achieve a good moderate bandwidth with much reduced total length in comparison with pure absorption design.

Novel recycling of nonmetal particles from waste printed wiring boards to produce porous composite for sound absorbing application.

PubMed

Sun, Zhixing; Shen, Zhigang; Zhang, Xiaojing; Ma, Shulin

2014-01-01

Nonmetal materials take up about 70 wt% of waste printed wiring boards (WPWB), which are usually recycled as low-value fillers or even directly disposed by landfill dumping and incineration. In this research, a novel reuse ofthe nonmetals to produce porous composites for sound absorbing application was demonstrated. The manufacturing process, absorbing performance and mechanical properties of the composites were studied. The results show that the high porous structure of the composites leads to an excellent sound absorption ability in broad-band frequency range. Average absorption coefficient of above 0.4 can be achievedby the composite in the frequency range from 100 to 6400 Hz. When the particle size is larger than 0.2 mm, the absorption ability of the composite is comparable to that of commercial wood-fibre board and urea-formaldehyde foam. Mechanical analysis indicates that the porous composites possess sufficient structural strength for self-sustaining applications. All the results indicate that producing sound absorbing composite with nonmetal particles from WPWB provides an efficient and profitable way for recycling this waste resource and can resolve both the environment pollution and noise pollution problems.

Temporal-Spectral Characterization and Classification of Marine Mammal Vocalizations and Diesel-Electric Ships Radiated Sound over Continental Shelf Scale Regions with Coherent Hydrophone Array Measurements

NASA Astrophysics Data System (ADS)

Huang, Wei

The passive ocean acoustic waveguide remote sensing (POAWRS) technology is capable of monitoring a large variety of underwater sound sources over instantaneous wide areas spanning continental-shelf scale regions. POAWRS uses a large-aperture densely-sampled coherent hydrophone array to significantly enhance the signal-to-noise ratio via beamforming, enabling detection of sound sources roughly two-orders of magnitude more distant in range than that possible with a single hydrophone. The sound sources detected by POAWRS include ocean biology, geophysical processes, and man-made activities. POAWRS provides detection, bearing-time estimation, localization, and classification of underwater sound sources. The volume of underwater sounds detected by POAWRS is immense, typically exceeding a million unique signal detections per day, in the 10-4000 Hz frequency range, making it a tremendously challenging task to distinguish and categorize the various sound sources present in a given region. Here we develop various approaches for characterizing and clustering the signal detections for various subsets of data acquired using the POAWRS technology. The approaches include pitch tracking of the dominant signal detections, time-frequency feature extraction, clustering and categorization methods. These approaches are essential for automatic processing and enhancing the efficiency and accuracy of POAWRS data analysis. The results of the signal detection, clustering and classification analysis are required for further POAWRS processing, including localization and tracking of a large number of oceanic sound sources. Here the POAWRS detection, localization and clustering approaches are applied to analyze and elucidate the vocalization behavior of humpback, sperm and fin whales in the New England continental shelf and slope, including the Gulf of Maine from data acquired using coherent hydrophone arrays. The POAWRS technology can also be applied for monitoring ocean vehicles. Here the approach is calibrated by application to known ships present in the Gulf of Maine and in the Norwegian Sea from their underwater sounds received using a coherent hydrophone array. The vocalization behavior of humpback whales was monitored over vast areas of the Gulf of Maine using the POAWRS technique over multiple diel cycles in Fall 2006. The humpback vocalizations, received at a rate of roughly 1800+/-1100 calls per day, comprised of both song and non-song. The song vocalizations, composed of highly structured and repeatable set of phrases, are characterized by inter-pulse intervals of 3.5 +/- 1.8 s. Songs were detected throughout the diel cycle, occuring roughly 40% during the day and 60% during the night. The humpback non-song vocalizations, dominated by shorter duration (≤3 s) downsweep and bow-shaped moans, as well as a small fraction of longer duration (˜5 s) cries, have significantly larger mean and more variable inter-pulse intervals of 14.2 +/- 11 s. The non-song vocalizations were detected at night with negligible detections during the day, implying they probably function as nighttime communication signals. The humpback song and non-song vocalizations are separately localized using the moving array triangulation and array invariant techniques. The humpback song and non-song moan calls are both consistently localized to a dense area on northeastern Georges Bank and a less dense region extended from Franklin Basin to the Great South Channel. Humpback cries occur exclusively on northeastern Georges Bank and during nights with coincident dense Atlantic herring shoaling populations, implying the cries are feeding-related. Sperm whales in the New England continental shelf and slope were passively localized and classified from their vocalizations received using a single low-frequency (<2500 Hz) densely-sampled horizontal coherent hydrophone array deployed in Spring 2013 in Gulf of Maine. Whale bearings were estimated using time-domain beamforming that provided high coherent array gain in sperm whale click signal-to-noise ratio. Whale ranges from the receiver array center were estimated using the moving array triangulation technique from a sequence of whale bearing measurements. Multiple concurrently vocalizing sperm whales, in the far-field of the horizontal receiver array, were distinguished and classified based on their horizontal spatial locations and the inter-pulse intervals of their vocalized click signals. We provide detailed analysis of over 15,000 fin whale 20 Hz vocalizations received on Oct 1-3, 2006 in the Gulf of Maine. These vocalizations are separated into 16 clusters following the clustering approaches. Seven of these types are prominent, each acounting for between 8% to 16% and together comprise roughly 85% of all the analyzed vocalizations. The 7 prominent clusters are each more abundant during nighttime hours by a factor of roughly 2.5 times than that of the daytime. The diel-spatial correlation of the 7 prominent clusters to the simultaneously observed densities of their fish prey, the Atlantic herring in the Gulf of Maine, is provided which implies that the factor of roughly 2.5 increase in call rate during night-time hours can be attributed to increased fish-feeding activities. (Abstract shortened by ProQuest.).

Sound velocity and absorption in a coarsening foam.

PubMed

Mujica, Nicolás; Fauve, Stéphan

2002-08-01

We present experimental measurements of sound velocity and absorption in a commercial shaving foam. We observe that both quantities evolve with time as the foam coarsens increasing its mean bubble radius . By varying the acoustic frequency we probe the foam from the large wavelength regime, lambda approximately 1500, down to the scale lambda approximately 20. Sound absorption alpha varies significantly with both the foam age and the excitation frequency. After an initial transition time of 20 min, the attenuation per wavelength, alphalambda, varies linearly with the foam age. In addition, for evolution times smaller than approximately 90 min, we observe that alphalambda scales linearly with both foam age and frequency. From these scalings we show that the thermal dissipation mechanism is the dominant one. Sound velocity c is initially frequency independent but the medium becomes slightly dispersive as the foam coarsens. We observe that sound velocity depends on the evolution of the structure of the foam, even in the large wavelength regime. After 2 h of foam coarsening, c decreases at least by a factor of 20%, due to the softening of the foam. These facts are explained by considering the liquid matrix elasticity, due to the presence of surfactant molecules. A simple model of foam structure, combined with results of Biot's theory for porous media, gives both good qualitative and quantitative agreement with our experimental results in the low frequency regime.

Observations of shallow water marine ambient sound: the low frequency underwater soundscape of the central Oregon coast.

PubMed

Haxel, Joseph H; Dziak, Robert P; Matsumoto, Haru

2013-05-01

A year-long experiment (March 2010 to April 2011) measuring ambient sound at a shallow water site (50 m) on the central OR coast near the Port of Newport provides important baseline information for comparisons with future measurements associated with resource development along the inner continental shelf of the Pacific Northwest. Ambient levels in frequencies affected by surf-generated noise (f < 100 Hz) characterize the site as a high-energy end member within the spectrum of shallow water coastal areas influenced by breaking waves. Dominant sound sources include locally generated ship noise (66% of total hours contain local ship noise), breaking surf, wind induced wave breaking and baleen whale vocalizations. Additionally, an increase in spectral levels for frequencies ranging from 35 to 100 Hz is attributed to noise radiated from distant commercial ship commerce. One-second root mean square (rms) sound pressure level (SPLrms) estimates calculated across the 10-840 Hz frequency band for the entire year long deployment show minimum, mean, and maximum values of 84 dB, 101 dB, and 152 dB re 1 μPa.

Blue whale vocalizations recorded around New Zealand: 1964-2013.

PubMed

Miller, Brian S; Collins, Kym; Barlow, Jay; Calderan, Susannah; Leaper, Russell; McDonald, Mark; Ensor, Paul; Olson, Paula A; Olavarria, Carlos; Double, Michael C

2014-03-01

Previous underwater recordings made in New Zealand have identified a complex sequence of low frequency sounds that have been attributed to blue whales based on similarity to blue whale songs in other areas. Recordings of sounds with these characteristics were made opportunistically during the Southern Ocean Research Partnership's recent Antarctic Blue Whale Voyage. Detections of these sounds occurred all around the South Island of New Zealand during the voyage transits from Nelson, New Zealand to the Antarctic and return. By following acoustic bearings from directional sonobuoys, blue whales were visually detected and confirmed as the source of these sounds. These recordings, together with the historical recordings made northeast of New Zealand, indicate song types that persist over several decades and are indicative of the year-round presence of a population of blue whales that inhabits the waters around New Zealand. Measurements of the four-part vocalizations reveal that blue whale song in this region has changed slowly, but consistently over the past 50 years. The most intense units of these calls were detected as far south as 53°S, which represents a considerable range extension compared to the limited prior data on the spatial distribution of this population.

Application of musical timbre discrimination features to active sonar classification

NASA Astrophysics Data System (ADS)

Young, Victor W.; Hines, Paul C.; Pecknold, Sean

2005-04-01

In musical acoustics significant effort has been devoted to uncovering the physical basis of timbre perception. Most investigations into timbre rely on multidimensional scaling (MDS), in which different musical sounds are arranged as points in multidimensional space. The Euclidean distance between points corresponds to the perceptual distance between sounds and the multidimensional axes are linked to measurable properties of the sounds. MDS has identified numerous temporal and spectral features believed to be important to timbre perception. There is reason to believe that some of these features may have wider application in the disparate field of underwater acoustics, since anecdotal evidence suggests active sonar returns from metallic objects sound different than natural clutter returns when auralized by human operators. This is particularly encouraging since attempts to develop robust automatic classifiers capable of target-clutter discrimination over a wide range of operational conditions have met with limited success. Spectral features relevant to target-clutter discrimination are believed to include click-pitch and envelope irregularity; relevant temporal features are believed to include duration, sub-band attack/decay time, and time separation pitch. Preliminary results from an investigation into the role of these timbre features in target-clutter discrimination will be presented. [Work supported by NSERC and GDC.

THE USE OF ARCHITECTURAL ACOUSTICAL MATERIALS, THEORY AND PRACTICE. SECOND EDITION.

ERIC Educational Resources Information Center

Acoustical Materials Association, New York, NY.

THIS DISCUSSION OF THE BASIC FUNCTION OF ACOUSTICAL MATERIALS--THE CONTROL OF SOUND BY SOUND ABSORPTION--IS BASED ON THE WAVE AND ENERGY PROPERTIES OF SOUND. IT IS STATED THAT, IN GENERAL, A MUCH LARGER VOLUME OF ACOUSTICAL MATERIALS IS NEEDED TO REMOVE DISTRACTING NOISE FROM CLASSROOMS AND OFFICES, FOR EXAMPLE, THAN FROM AUDITORIUMS, WHERE A…

75 FR 38783 - Takes of Marine Mammals Incidental to Specified Activities; Manette Bridge Replacement in...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-06

... sound absorption in the water column. Once impact pile driving begins, NMFS requires that the contractor... 2010. The Manette Bridge is located within the Puget Sound of Washington State, at the outlet to the... Sinclair Inlet, and connection to the greater Puget Sound. The Manette Bridge is determined to be a...

Broadband high sound absorption from labyrinthine metasurfaces

NASA Astrophysics Data System (ADS)

Chang, Huiting; Liu, Liu; Zhang, Chi; Hu, Xinhua

2018-04-01

Metamaterials are artificial structures which exhibit fascinating properties unreachable by traditional materials. Here, we report on the design, fabrication, and characterization of acoustic metasurfaces consisting of dead-end channels coiled in a 2D plane. It is found that when the area of the channel's cross section is about 1/10 of the area (4.3 cm × 4.3 cm) of the upper surface of the building block, the sound loss in channels approaches to a critical value, resulting in near-perfect absorption (A > 99%) at resonant frequency. When the building block contains ten channels with specially designed lengths, sound waves can be highly absorbed above a cutoff frequency fc (A > 90% for fc < f < 3fc). The wavelength at the cutoff frequency can be 7.1 times of the thickness of the metasurface. Our results could find applications in noise reduction and sound detection.

Monitoring ship noise to assess the impact of coastal developments on marine mammals.

PubMed

Merchant, Nathan D; Pirotta, Enrico; Barton, Tim R; Thompson, Paul M

2014-01-15

The potential impacts of underwater noise on marine mammals are widely recognised, but uncertainty over variability in baseline noise levels often constrains efforts to manage these impacts. This paper characterises natural and anthropogenic contributors to underwater noise at two sites in the Moray Firth Special Area of Conservation, an important marine mammal habitat that may be exposed to increased shipping activity from proposed offshore energy developments. We aimed to establish a pre-development baseline, and to develop ship noise monitoring methods using Automatic Identification System (AIS) and time-lapse video to record trends in noise levels and shipping activity. Our results detail the noise levels currently experienced by a locally protected bottlenose dolphin population, explore the relationship between broadband sound exposure levels and the indicators proposed in response to the EU Marine Strategy Framework Directive, and provide a ship noise assessment toolkit which can be applied in other coastal marine environments. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Short-Range Acoustic Propagation Using Mobile Transmitters Under Arctic Ice Cover

DTIC Science & Technology

2017-09-01

predict the surface water/ice scattering and absorptive effects on transmitted sound . In addition, sound speed variability by range (usually...receivers at ranges out to 10 kilometers. Sound speed profile data was also measured on site. Transmission loss models were created as a baseline at the...received sound level (on the level of 30 to 40 decibels) at the same range and depth but different directions. 14. SUBJECT TERMS Arctic, Beaufort Sea

Aperture size, materiality of the secondary room, and listener location: Impact on the simulated impulse response of a coupled-volume concert hall

NASA Astrophysics Data System (ADS)

Ermann, Michael; Johnson, Marty E.; Harrison, Byron W.

2002-11-01

By adding a second room to a concert hall, and designing doors to control the sonic transparency between the two rooms, designers can create a new, coupled acoustic. Concert halls use coupling to achieve a variable, longer, and distinct reverberant quality for their musicians and listeners. For this study, a coupled-volume concert hall based on an existing performing arts center is conceived and computer modeled. It has a fixed geometric volume, form, and primary-room sound absorption. Ray-tracing software simulates impulse responses, varying both aperture size and secondary-room sound-absorption level, across a grid of receiver (listener) locations. The results are compared with statistical analysis that suggests a highly sensitive relationship between the double-sloped condition and the architecture of the space. This line of study aims to quantitatively and spatially correlate the double-sloped condition with (1) aperture size exposing the chamber, (2) sound absorptance in the coupled volume, and (3) listener location.

Aperture size, materiality of the secondary room and listener location: Impact on the simulated impulse response of a coupled-volume concert hall

NASA Astrophysics Data System (ADS)

Ermann, Michael; Johnson, Marty E.; Harrison, Byron W.

2003-04-01

By adding a second room to a concert hall, and designing doors to control the sonic transparency between the two rooms, designers can create a new, coupled acoustic. Concert halls use coupling to achieve a variable, longer and distinct reverberant quality for their musicians and listeners. For this study, a coupled-volume concert hall based on an existing performing arts center is conceived and computer-modeled. It has a fixed geometric volume, form and primary-room sound absorption. Ray-tracing software simulates impulse responses, varying both aperture size and secondary-room sound absorption level, across a grid of receiver (listener) locations. The results are compared with statistical analysis that suggests a highly sensitive relationship between the double-sloped condition and the architecture of the space. This line of study aims to quantitatively and spatially correlate the double-sloped condition with (1) aperture size exposing the chamber, (2) sound absorptance in the coupled volume, and (3) listener location.

Directionally Antagonistic Graphene Oxide-Polyurethane Hybrid Aerogel as a Sound Absorber.

PubMed

Oh, Jung-Hwan; Kim, Jieun; Lee, Hyeongrae; Kang, Yeonjune; Oh, Il-Kwon

2018-06-21

Innovative sound absorbers, the design of which is based on carbon nanotubes and graphene derivatives, could be used to make more efficient sound absorbing materials because of their excellent intrinsic mechanical and chemical properties. However, controlling the directional alignments of low-dimensional carbon nanomaterials, such as restacking, alignment, and dispersion, has been a challenging problem when developing sound absorbing forms. Herein, we present the directionally antagonistic graphene oxide-polyurethane hybrid aerogel we developed as a sound absorber, the physical properties of which differ according to the alignment of the microscopic graphene oxide sheets. This porous graphene sound absorber has a microporous hierarchical cellular structure with adjustable stiffness and improved sound absorption performance, thereby overcoming the restrictions of both geometric and function-orientated functions. Furthermore, by controlling the inner cell size and aligned structure of graphene oxide layers in this study, we achieved remarkable improvement of the sound absorption performance at low frequency. This improvement is attributed to multiple scattering of incident and reflection waves on the aligned porous surfaces, and air-viscous resistance damping inside interconnected structures between the urethane foam and the graphene oxide network. Two anisotropic sound absorbers based on the directionally antagonistic graphene oxide-polyurethane hybrid aerogels were fabricated. They show remarkable differences owing to the opposite alignment of graphene oxide layers inside the polyurethane foam and are expected to be appropriate for the engineering design of sound absorbers in consideration of the wave direction.

A model for the vertical sound speed and absorption profiles in Titan's atmosphere based on Cassini-Huygens data.

PubMed

Petculescu, Andi; Achi, Peter

2012-05-01

Measurements of thermodynamic quantities in Titan's atmosphere during the descent of Huygens in 2005 are used to predict the vertical profiles for the speed and intrinsic attenuation (or absorption) of sound. The calculations are done using one author's previous model modified to accommodate non-ideal equations of state. The vertical temperature profile places the tropopause about 40 km above the surface. In the model, a binary nitrogen-methane composition is assumed for Titan's atmosphere, quantified by the methane fraction measured by the gas chromatograph/mass spectrometer (GCMS) onboard Huygens. To more accurately constrain the acoustic wave number, the variation of thermophysical properties (specific heats, viscosity, and thermal conductivity) with altitude is included via data extracted from the NIST Chemistry WebBook [URL webbook.nist.gov, National Institute of Standards and Technology Chemistry WebBook (Last accessed 10/20/2011)]. The predicted speed of sound profile fits well inside the spread of the data recorded by Huygens' active acoustic sensor. In the N(2)-dominated atmosphere, the sound waves have negligible relaxational dispersion and mostly classical (thermo-viscous) absorption. The cold and dense environment of Titan can sustain acoustic waves over large distances with relatively small transmission losses, as evidenced by the small absorption. A ray-tracing program is used to assess the bounds imposed by the zonal wind-measured by the Doppler Wind Experiment on Huygens-on long-range propagation.

King County Nearshore Habitat Mapping Data Report: Picnic Point to Shilshole Bay Marina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodruff, Dana L.; Farley, Paul J.; Borde, Amy B.

2000-12-31

The objective of this study is to provide accurate, georeferenced maps of benthic habitats to assist in the siting of a new wastewater treatment plant outfall and the assessment of habitats of endangered, threatened, and economically important species. The mapping was conducted in the fall of 1999 using two complementary techniques: side-scan sonar and underwater videography. Products derived from these techniques include geographic information system (GIS) compatible polygon data of substrate type and vegetation cover, including eelgrass and kelp. Additional GIS overlays include underwater video track line data of total macroalgae, selected macroalgal species, fish, and macroinvertebrates. The combined toolsmore » of geo-referenced side-scan sonar and underwater video is a powerful technique for assessing and mapping of nearshore habitat in Puget Sound. Side-scan sonar offers the ability to map eelgrass with high spatial accuracy and resolution, and provides information on patch size, shape, and coverage. It also provides information on substrate change and location of specific targets (e.g., piers, docks, pilings, large boulders, debris piles). The addition of underwater video is a complementary tool providing both groundtruthing for the sonar and additional information on macro fauna and flora. As a groundtruthing technique, the video was able to confirm differences between substrate types, as well as detect subtle spatial changes in substrate. It also verified information related to eelgrass, including the density classification categories and the type of substrate associated with eelgrass, which could not be determined easily with side- scan sonar. Video is also a powerful tool for mapping the location of macroalgae, (including kelp and Ulva), fish and macroinvertebrates. The ability to geo-locate these resources in their functional habitat provides an added layer of information and analytical potential.« less

The sounds of science

NASA Astrophysics Data System (ADS)

Carlowicz, Michael

As scientists carefully study some aspects of the ocean environment, are they unintentionally distressing others? That is a question to be answered by Robert Benson and his colleagues in the Center for Bioacoustics at Texas A&M University.With help from a 3-year, $316,000 grant from the U.S. Office of Naval Research, Benson will study how underwater noise produced by naval operations and other sources may affect marine mammals. In Benson's study, researchers will generate random sequences of low-frequency, high-intensity (180-decibel) sounds in the Gulf of Mexico, working at an approximate distance of 1 km from sperm whale herds. Using an array of hydrophones, the scientists will listen to the characteristic clicks and whistles of the sperm whales to detect changes in the animals' direction, speed, and depth, as derived from fluctuations in their calls.

Acoustic Characterization of Fluorinert FC-43 Liquid with Helium Gas Bubbles: Numerical Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vanhille, Christian; Pantea, Cristian; Sinha, Dipen N.

In this work, we define the acoustic characteristics of a biphasic fluid consisting of static helium gas bubbles in liquid Fluorinert FC-43 and study the propagation of ultrasound of finite amplitudes in this medium. Very low sound speed and high sound attenuation are found, in addition to a particularly high acoustic nonlinear parameter. This result suggests the possibility of using this medium as a nonlinear enhancer in various applications. In particular, parametric generation of low ultrasonic frequencies is studied in a resonator cavity as a function of driving pressure showing high conversion efficiency. This work suggests that this medium couldmore » be used for applications such as parametric arrays, nondestructive testing, diagnostic medicine, sonochemistry, underwater acoustics, and ultrasonic imaging and to boost the shock formation in fluids.« less

Acoustic Characterization of Fluorinert FC-43 Liquid with Helium Gas Bubbles: Numerical Experiments

DOE PAGES

Vanhille, Christian; Pantea, Cristian; Sinha, Dipen N.

2017-01-19

In this work, we define the acoustic characteristics of a biphasic fluid consisting of static helium gas bubbles in liquid Fluorinert FC-43 and study the propagation of ultrasound of finite amplitudes in this medium. Very low sound speed and high sound attenuation are found, in addition to a particularly high acoustic nonlinear parameter. This result suggests the possibility of using this medium as a nonlinear enhancer in various applications. In particular, parametric generation of low ultrasonic frequencies is studied in a resonator cavity as a function of driving pressure showing high conversion efficiency. This work suggests that this medium couldmore » be used for applications such as parametric arrays, nondestructive testing, diagnostic medicine, sonochemistry, underwater acoustics, and ultrasonic imaging and to boost the shock formation in fluids.« less

The shock formation distance in a bounded sound beam of finite amplitude.

PubMed

Tao, Chao; Ma, Jian; Zhu, Zhemin; Du, Gonghuan; Ping, Zihong

2003-07-01

This paper investigates the shock formation distance in a bounded sound beam of finite amplitude by solving the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation using frequency-domain numerical method. Simulation results reveal that, besides the nonlinearity and absorption, the diffraction is another important factor that affects the shock formation of a bounded sound beam. More detailed discussions of the shock formation in a bounded sound beam, such as the waveform of sound pressure and the spatial distribution of shock formation, are also presented and compared for different parameters.

Problems in Nonlinear Acoustics: Pulsed Finite Amplitude Sound Beams, Nonlinear Propagation of Sound in Layered Media, Time Domain Solutions for Focused Sound Beams, Focusing of Sound with an Ellipsoidal Mirror, and Modeling Finite Amplitude Propagation in Waveguides.

DTIC Science & Technology

1991-08-01

performed entirely in the time domain, solves the KZK (Khokhlov-Zabolotskaya-Kuznetsov) nonlinear parabolic wdve equation for pulsed, axisymmetric...finite amplitude sound beams. The KZK equation accounts for the combined effects of nonlinearity, diffraction and thermoviscous absorption on the...those used by Naze Tjotta, Tjotta, and Vefring to produce Fig. 7 of Ref. 4 with a frequency domain numerical solution of the KZK equation. However

Modelling the light absorption coefficients of oceanic waters: Implications for underwater optical applications

NASA Astrophysics Data System (ADS)

Prabhakaran, Sai Shri; Sahu, Sanjay Kumar; Dev, Pravin Jeba; Shanmugam, Palanisamy

2018-05-01

Spectral absorption coefficients of particulate (algal and non-algal components) and dissolved substances are modelled and combined with the pure seawater component to determine the total light absorption coefficients of seawater in the Bay of Bengal. Two parameters namely chlorophyll-a (Chl) concentration and turbidity were measured using commercially available instruments with high sampling rates. For modelling the light absorption coefficients of oceanic waters, the measured data are classified into two broad groups - algal dominant and non-algal particle (NAP) dominant. With these criteria the individual absorption coefficients of phytoplankton and NAP were established based on their concentrations using an iterative method. To account for the spectral dependence of absorption by phytoplankton, the wavelength-dependent coefficients were introduced into the model. The CDOM absorption was determined by subtracting the individual absorption coefficients of phytoplankton and NAP from the measured total absorption data and then related to the Chl concentration. Validity of the model is assessed based on independent in-situ data from certain discrete locations in the Bay of Bengal. The total absorption coefficients estimated using the new model by considering the contributions of algal, non-algal and CDOM have good agreement with the measured total absorption data with the error range of 6.9 to 28.3%. Results obtained by the present model are important for predicting the propagation of the radiant energy within the ocean and interpreting remote sensing observation data.

Multi-LED parallel transmission for long distance underwater VLC system with one SPAD receiver

NASA Astrophysics Data System (ADS)

Wang, Chao; Yu, Hong-Yi; Zhu, Yi-Jun; Wang, Tao; Ji, Ya-Wei

2018-03-01

In this paper, a multiple light emitting diode (LED) chips parallel transmission (Multi-LED-PT) scheme for underwater visible light communication system with one photon-counting single photon avalanche diode (SPAD) receiver is proposed. As the lamp always consists of multi-LED chips, the data rate could be improved when we drive these multi-LED chips parallel by using the interleaver-division-multiplexing technique. For each chip, the on-off-keying modulation is used to reduce the influence of clipping. Then a serial successive interference cancellation detection algorithm based on ideal Poisson photon-counting channel by the SPAD is proposed. Finally, compared to the SPAD-based direct current-biased optical orthogonal frequency division multiplexing system, the proposed Multi-LED-PT system could improve the error-rate performance and anti-nonlinearity performance significantly under the effects of absorption, scattering and weak turbulence-induced channel fading together.

Professor Joseph Warren Horton (1889-1967): biological engineer.

PubMed

Zeitlin, Gerald L

2005-02-01

Joseph Warren Horton graduated with a degree in electrical engineering from the Massachusetts Institute of Technology (MIT) in 1914. He became involved in the early development of electrical measurement devices, televised image transmission, and the detection of underwater sound transmission. In the mid-1930s he was appointed the first leader of the newly created Department of Biological Engineering at MIT and in this position he made major contributions to the application of physics to human physiology, in particular by increasing the safety of explosive inhalational anaesthetic agents.

Design and Implementation of a Collision Avoidance System for the NPS autonomous Underwater Vehicle (AUV II) Utilizing Ultrasonic Sensors

DTIC Science & Technology

1991-09-01

exectti:n by providing geographic waypoints and tasks to the guidance system. The guidance system provides desired vehicle postures, ( x , y, z, 0), as...Maker Guidance System Patter ( x ,y,zlt) Recognition LOS Cross Track No Cubic Spiral Heading Spee Depth Mode Commands Navigation Autopilot System Systems...20log2r + 2otr (Eq 3.3) where ( x is the attenuation coefficient of sound in water at the frequency in use and r is the length of the transmission

SUS Source Level Error Analysis

DTIC Science & Technology

1978-01-20

RIECIP1IEN’ CATALOG NUMBER * ITLE (and SubaltIe) S. TYP aof REPORT & _V9RCO SUS~ SOURCE LEVEL ERROR ANALYSIS & Fia 1.r,. -. pAURWORONTIUMm N (s)$S...Fourier Transform (FFTl) SUS Signal model ___ 10 TRA&C (CeEOINIMII1& ro"* *140O tidat n9#*#*Y a"d 0e~ntiff 6T 69*.4 apbt The report provides an analysis ...of major terms which contribute to signal analysis error in a proposed experiment to c-librate sourr - I levels of SUS (Signal Underwater Sound). A

Characterization of Underwater Sounds Produced by a Hydraulic Cutterhead Dredge during Maintenance Dredging in the Stockton Deepwater Shipping Channel, California

DTIC Science & Technology

2014-03-01

SDWSC with the confluence of the San Joaquin River. Ambient monitoring stations are identified by yellow circles. (Red “X” = location of Lusitania G...associated with a running generator from the bulk carrier Lusitania G. There is also a noise event, approximately 125 seconds on the time-series profile...noise emitted from the bulk carrier Lusitania G, moored on the east side of the SJR. Site C was located directly astern of the bulk carrier, nearest the

Hardware-in-the-loop simulation for undersea vehicle applications

NASA Astrophysics Data System (ADS)

Kelf, Michael A.

2001-08-01

Torpedoes and other Unmanned Undersea Vehicles (UUV) are employed by submarines and surface combatants, as well as aircraft, for undersea warfare. These vehicles are autonomous devices whose guidance systems rival the complexity of the most sophisticated air combat missiles. The tactical environment for undersea warfare is a difficult one in terms of target detection,k classification, and pursuit because of the physics of underwater sounds. Both hardware-in-the-loop and all-digital simulations have become vital tools in developing and evaluating undersea weapon and vehicle guidance performance in the undersea environment.

Do top predators cue on sound production by mesopelagic prey?

NASA Astrophysics Data System (ADS)

Baumann-Pickering, S.; Checkley, D. M., Jr.; Demer, D. A.

2016-02-01

Deep-scattering layer (DSL) organisms, comprising a variety of mesopelagic fishes, and squids, siphonophores, crustaceans, and other invertebrates, are preferred prey for numerous large marine predators, e.g. cetaceans, seabirds, and fishes. Some of the DSL species migrate from depth during daylight to feed near the surface at night, transitioning during dusk and dawn. We investigated if any DSL organisms create sound, particularly during the crepuscular periods. Over several nights in summer 2015, underwater sound was recorded in the San Diego Trough using a high-frequency acoustic recording package (HARP, 10 Hz to 100 kHz), suspended from a drifting surface float. Acoustic backscatter from the DSL was monitored nearby using a calibrated multiple-frequency (38, 70, 120, and 200 kHz) split-beam echosounder (Simrad EK60) on a small boat. DSL organisms produced sound, between 300 and 1000 Hz, and the received levels were highest when the animals migrated past the recorder during ascent and descent. The DSL are globally present, so the observed acoustic phenomenon, if also ubiquitous, has wide-reaching implications. Sound travels farther than light or chemicals and thus can be sensed at greater distances by predators, prey, and mates. If sound is a characteristic feature of pelagic ecosystems, it likely plays a role in predator-prey relationships and overall ecosystem dynamics. Our new finding inspires numerous questions such as: Which, how, and why have DSL organisms evolved to create sound, for what do they use it and under what circumstances? Is sound production by DSL organisms truly ubiquitous, or does it depend on the local environment and species composition? How may sound production and perception be adapted to a changing environment? Do predators react to changes in sound? Can sound be used to quantify the composition of mixed-species assemblages, component densities and abundances, and hence be used in stock assessment or predictive modeling?

Light aircraft sound transmission studies - Noise reduction model

NASA Technical Reports Server (NTRS)

Atwal, Mahabir S.; Heitman, Karen E.; Crocker, Malcolm J.

1987-01-01

Experimental tests conducted on the fuselage of a single-engine Piper Cherokee light aircraft suggest that the cabin interior noise can be reduced by increasing the transmission loss of the dominant sound transmission paths and/or by increasing the cabin interior sound absorption. The validity of using a simple room equation model to predict the cabin interior sound-pressure level for different fuselage and exterior sound field conditions is also presented. The room equation model is based on the sound power flow balance for the cabin space and utilizes the measured transmitted sound intensity data. The room equation model predictions were considered good enough to be used for preliminary acoustical design studies.

Acoustic scale modelling of factories, part II: 1-50 Cale model investigations of factory sound fields

NASA Astrophysics Data System (ADS)

Hodgson, M. R.; Orlowski, R. J.

1987-03-01

In this second part of a report on factory scale modelling use of a 1:50 scale variable model as a research tool is described. Details of the model are presented. The results of measurements of reverberation time and sound propagation, made in various model configurations, are used to investigate the main factors influencing factory sound fields, and the applicability of the Sabine theory to factories. The parameters investigated are the enclosure geometry (aspect ratio, volume and roof pitch), surface absorption and fittings (density, size, surface area, vertical distribution and specific types). Despite certain limitations and uncertainties resulting, for example, from surprising results associated with surface absorption, models are shown to be effective research tools. The inapplicability of the Sabine theory is confirmed and elucidated.