Next Generation HeliMag UXO Mapping Technology

DTIC Science & Technology

2010-01-01

Ancillary instrumentation records aircraft height above ground and attitude. A fluxgate magnetometer is used to allow for aeromagnetic compensation of... Magnetometer System WWII World War II WAA wide area assessment ACKNOWLEDGEMENTS This Next Generation HeliMag Unexploded Ordnance (UXO) Mapping...for deployment of seven total-field magnetometers on a Kevlar reinforced boom mounted on a Bell 206L helicopter. The objectives of this

Clearing Unexploded Ordnance: Bayesian Methodology for Assessing Success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, K K.

2005-10-30

The Department of Defense has many Formerly Used Defense Sites (FUDS) that are slated for transfer for public use. Some sites have unexploded ordnance (UXO) that must be cleared prior to any land transfers. Sites are characterized using geophysical sensing devices and locations are identified where possible UXO may be located. In practice, based on the analysis of the geophysical surveys, a dig list of N suspect locations is created for a site that is possibly contaminated with UXO. The suspect locations on the dig list are often assigned into K bins ranging from ``most likely to contain UXO" tomore » ``least likely to be UXO" based on signal discrimination techniques and expert judgment. Usually all dig list locations are sampled to determine if UXO is present before the site is determined to be free of UXO. While this method is 100% certain to insure no UXO remains in the locations identified by the signal discrimination and expert judgment, it is very costly. This paper proposes a statistical Bayesian methodology that may result in digging less than 100% of the suspect locations to reach a pre-defined tolerable risk, where risk is defined in terms of a low probability that any UXO remains in the unsampled dig list locations. Two important features of a Bayesian approach are that it can account for uncertainties in model parameters and that it can handle data that becomes available in stages. The results from each stage of data can be used to direct the subsequent digs.« less

UXO Navigation Technology

DTIC Science & Technology

2008-10-01

modeling operator and dobs is the observed data (details in Pasion 2007). Figure 42. Geometry of EM61HH-MK2 sensor. The transmitter and receiver...1979. Stochastic models, estimation, and control (Vol. 141). Pasion , L. R., 2007. Inversion of Time Domain Electromagnetic Data for the Detection of...Unexploded Ordnance. Ph.D. Thesis, The University of British Columbia. Pasion , L. R., Oldenburg, D. W., 2001. A Discrimination Algorithm for UXO

Robotic Range Clearance Competition (R2C2)

DTIC Science & Technology

2011-10-01

unexploded ordnance (UXO). A large part of the debris field consists of ferrous metal objects that magnetic 39 Distribution A: Approved for public...was set at 7 degrees above horizontal based on terrain around the Base station. We used the BSUBR file for all fields except the Subsurface...and subsurface clearance test areas had numerous pieces of simulated unexploded ordinance (SUXO) buried at random locations around the field . These

Shallow Water UXO Technology Demonstration Site, Scoring Record No. 4 (CTC, FEREX DLG-GPS), MAG)

DTIC Science & Technology

2008-04-01

Detection and Discrimination Demonstration of a Fluxgate Vertical Gradient Magnetometer at the Aberdeen Shallow Water Test Site. Submitted in...TECHNOLOGY TYPE/PLATFORM: FEREX DLG-GPS MAGNETOMETER SYSTEM PREPARED BY: U.S. ARMY ABERDEEN TEST CENTER ABERDEEN PROVING GROUND, MD 21005...efforts of Concurrent Technologies Corporation (CTC) to detect and discriminate inert unexploded ordnance (UXO) using a FEREX DLG- magnetometer with a

Predicting the Mobility and Burial of Underwater Unexploded Ordnance (UXO) Using the UXO Mobility Model (ESTCP) 200417

DTIC Science & Technology

2009-11-01

Abbreviations and Acronyms Acronym Definition ADCP Acoustic Doppler Current Profiler AGD Applications Guidance Document ARAMS Army Risk Assessment Modeling...Center iv NESDI Navy Environmental Sustainability Development to Integration NOS National Ocean Service NS Naval Station NWS Naval Weapons...Plan QAS Quality Assurance Specialist RAC Risk Assessment Code REF/DIF Refraction/Diffraction ROI Return on Investment SAJ Dr. Scott A. Jenkins

Accounting for geophysical information in geostatistical characterization of unexploded ordnance (UXO) sites.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saito, Hirotaka; Goovaerts, Pierre; McKenna, Sean Andrew

2003-06-01

Efficient and reliable unexploded ordnance (UXO) site characterization is needed for decisions regarding future land use. There are several types of data available at UXO sites and geophysical signal maps are one of the most valuable sources of information. Incorporation of such information into site characterization requires a flexible and reliable methodology. Geostatistics allows one to account for exhaustive secondary information (i.e.,, known at every location within the field) in many different ways. Kriging and logistic regression were combined to map the probability of occurrence of at least one geophysical anomaly of interest, such as UXO, from a limited numbermore » of indicator data. Logistic regression is used to derive the trend from a geophysical signal map, and kriged residuals are added to the trend to estimate the probabilities of the presence of UXO at unsampled locations (simple kriging with varying local means or SKlm). Each location is identified for further remedial action if the estimated probability is greater than a given threshold. The technique is illustrated using a hypothetical UXO site generated by a UXO simulator, and a corresponding geophysical signal map. Indicator data are collected along two transects located within the site. Classification performances are then assessed by computing proportions of correct classification, false positive, false negative, and Kappa statistics. Two common approaches, one of which does not take any secondary information into account (ordinary indicator kriging) and a variant of common cokriging (collocated cokriging), were used for comparison purposes. Results indicate that accounting for exhaustive secondary information improves the overall characterization of UXO sites if an appropriate methodology, SKlm in this case, is used.« less

Classification of Uxo by Principal Dipole Polarizability

NASA Astrophysics Data System (ADS)

Kappler, K. N.

2010-12-01

Data acquired by multiple-Transmitter, multiple-receiver time-domain electromagnetic devices show great potential for determining the geometric and compositional information relating to near surface conductive targets. Here is presented an analysis of data from one such system; the Berkeley Unexploded-ordnance Discriminator (BUD) system. BUD data are succinctly reduced by processing the multi-static data matrices to obtain magnetic dipole polarizability matrices for data from each time gate. When viewed over all time gates, the projections of the data onto the principal polar axes yield so-called polarizability curves. These curves are especially well suited to discriminating between subsurface conductivity anomalies which correspond to objects of rotational symmetry and irregularly shaped objects. The curves have previously been successfully employed as library elements in a pattern recognition scheme aimed at discriminating harmless scrap metal from dangerous intact unexploded ordnance. However, previous polarizability-curve matching methods have only been applied at field sites which are known a priori to be contaminated by a single type of ordnance, and furthermore, the particular ordnance present in the subsurface was known to be large. Thus signal amplitude was a key element in the discrimination process. The work presented here applies feature-based pattern classification techniques to BUD field data where more than 20 categories of object are present. Data soundings from a calibration grid at the Yuma, AZ proving ground are used in a cross validation study to calibrate the pattern recognition method. The resultant method is then applied to a Blind Test Grid. Results indicate that when lone UXO are present and SNR is reasonably high, Polarizability Curve Matching successfully discriminates UXO from scrap metal when a broad range of objects are present.

Predicting the Mobility and Burial of Underwater Unexploded Ordnance (UXO) using the UXO Mobility Model. Field Test Report (PMRF Barking Sands, Kauai, Hawaii)

DTIC Science & Technology

2008-05-20

of the demonstration; yellow stars indicate the inshore and offshore fields. ................. 39 Figure 19. Wave height (upper) and current...demonstration; yellow stars indicate the inshore and offshore fields. 40 Figure 19. Wave height (upper) and current magnitude (lower) measured...State Park to Barking Sands, are composed of material eroded from the Kokee Highlands, remnant of a shield volcano that is dissected on its western side

Applications of the associated-particle neutron-time-of-flight interrogation technique - From sheep to unexploded ordnance

NASA Astrophysics Data System (ADS)

Mitra, S.

2013-04-01

The associated-particle technique (APT) will be presented for some diverse applications that include on the one hand, analyzing the body composition of live sheep and on the other, identifying the fillers of unexploded ordnance (UXO). What began with proof-of-concept studies using a large laboratory based 14 MeV neutron generator of the "associated-particle" type, soon became possible for the first time to measure total body protein, fat and water simultaneously in live sheep using a compact field deployable associated-particle sealed-tube neutron generator (APSTNG). This non-invasive technique offered the animal physiologist a tool to monitor the growth of an animal in response to new genetic, nutritional and pharmacologic methods for livestock improvement. While measurement of carbon (C), nitrogen (N) and oxygen (O) determined protein, fat and water because of the fixed stoichiometric proportions of these elements in these body components, the unique C/N and C/O ratios of high explosives revealed their identity in UXO. The algorithm that was developed and implemented to extract C, N and O counts from an APT generated gamma-ray spectrum will be presented together with the UXO investigations that involved preliminary proofof-concept studies and modeling with Monte Carlo produced synthetic spectra of 57-155 mm projectiles.

Applications of the associated-particle neutron-time-of-flight interrogation technique - From sheep to unexploded ordnance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitra, S.

The associated-particle technique (APT) will be presented for some diverse applications that include on the one hand, analyzing the body composition of live sheep and on the other, identifying the fillers of unexploded ordnance (UXO). What began with proof-of-concept studies using a large laboratory based 14 MeV neutron generator of the 'associated-particle' type, soon became possible for the first time to measure total body protein, fat and water simultaneously in live sheep using a compact field deployable associated-particle sealed-tube neutron generator (APSTNG). This non-invasive technique offered the animal physiologist a tool to monitor the growth of an animal in responsemore » to new genetic, nutritional and pharmacologic methods for livestock improvement. While measurement of carbon (C), nitrogen (N) and oxygen (O) determined protein, fat and water because of the fixed stoichiometric proportions of these elements in these body components, the unique C/N and C/O ratios of high explosives revealed their identity in UXO. The algorithm that was developed and implemented to extract C, N and O counts from an APT generated gamma-ray spectrum will be presented together with the UXO investigations that involved preliminary proofof-concept studies and modeling with Monte Carlo produced synthetic spectra of 57-155 mm projectiles.« less

Using unmanned aerial vehicle-borne magnetic sensors to detect and locate improvised explosive devices and unexploded ordnance

NASA Astrophysics Data System (ADS)

Trammell, Hoke S., III; Perry, Alexander R.; Kumar, Sankaran; Czipott, Peter V.; Whitecotton, Brian R.; McManus, Tobin J.; Walsh, David O.

2005-05-01

Magnetic sensors configured as a tensor magnetic gradiometer not only detect magnetic targets, but also determine their location and their magnetic moment. Magnetic moment information can be used to characterize and classify objects. Unexploded ordnance (UXO) and thus many types of improvised explosive device (IED) contain steel, and thus can be detected magnetically. Suitable unmanned aerial vehicle (UAV) platforms, both gliders and powered craft, can enable coverage of a search area much more rapidly than surveys using, for instance, total-field magnetometers. We present data from gradiometer passes over different shells using a gradiometer mounted on a moving cart. We also provide detection range and speed estimates for aerial detection by a UAV.

Improved Magnetic STAR Methods for Real-Time, Point-by-Point Localization of Unexploded Ordnance and Buried Mines

DTIC Science & Technology

2008-09-01

of magnetic UXO. The prototype STAR Sensor comprises: a) A cubic array of eight fluxgate magnetometers . b) A 24-channel data acquisition/signal...array (shaded boxes) of eight low noise Triaxial Fluxgate Magnetometers (TFM) develops 24 channels of vector B- field data. Processor hardware

Stratification of risk to the surgical team in removal of small arms ammunition implanted in the craniofacial region: case report.

PubMed

Forbes, Jonathan A; Laughlin, Ian; Newberry, Shane; Ryhn, Michael; Pasley, Jason; Newberry, Travis

2016-09-01

In cases of penetrating injury with implantation of small arms ammunition, it can often be difficult to tell the difference between simple ballistics and ballistics associated with unexploded ordnances (UXOs). In the operative environment, where highly flammable substances are often close to the surgical site, detonation of UXOs could have catastrophic consequences for both the patient and surgical team. There is a paucity of information in the literature regarding how to evaluate whether an implanted munition contains explosive material. This report describes a patient who presented during Operation Enduring Freedom with an implanted munition suspicious for a UXO and the subsequent workup organized by Explosive Ordnance Disposal (EOD) Company prior to surgical removal. Clinical risk factors for UXOs include assassination attempts and/or wartime settings. Specific radiological features suggestive of a UXO include projectile size greater than 7.62-mm caliber, alterations in density of the tip, as well as radiological evidence of a hollowed-out core. If an implanted UXO is suspected, risks to the surgical and anesthesia teams can be minimized by notifying the nearest military installation with EOD capabilities and following clinical practice guidelines set forth by the Joint Theater Trauma System.

Delineating high-density areas in spatial Poisson fields from strip-transect sampling using indicator geostatistics: application to unexploded ordnance removal.

PubMed

Saito, Hirotaka; McKenna, Sean A

2007-07-01

An approach for delineating high anomaly density areas within a mixture of two or more spatial Poisson fields based on limited sample data collected along strip transects was developed. All sampled anomalies were transformed to anomaly count data and indicator kriging was used to estimate the probability of exceeding a threshold value derived from the cdf of the background homogeneous Poisson field. The threshold value was determined so that the delineation of high-density areas was optimized. Additionally, a low-pass filter was applied to the transect data to enhance such segmentation. Example calculations were completed using a controlled military model site, in which accurate delineation of clusters of unexploded ordnance (UXO) was required for site cleanup.

Observing Migration and Burial of Unexploded Ordnance in the Nearshore Environment with Instrumented Surrogates

NASA Astrophysics Data System (ADS)

Bruder, B. L.; Cristaudo, D.; Puleo, J. A.

2016-12-01

Prior to 1972, it was legal and common practice to unload unexploded ordnance (UXO) into the ocean. Only 60-100 miles off the US coast alone there are 72 dumping sites where it is estimated 31 million pounds of UXO lie. As recently as 2015, UXO have been found not only in the nearshore environment, but on populated beaches. Thus, understanding the migration and burial of these objects is not only of oceanographic interest, but a matter of public safety. The presented project evaluates the efficacy of instrumented UXO surrogates for observing munition migration and burial. Instrumented surrogates were exposed to near prototype scale wave conditions over a mobile bed at the Littoral Warfare Environment at Aberdeen Test Center, MD. Surrogates were deployed in the swash zone, inner and outer surf zones. Dependent on munition size, surrogates housed multiple suites of self-logging sensors. Sensor suites included different combinations of inertial motion units, ultra-wideband tracking tags, pressure transducers, shock recorders, and photocells. Preliminary results show sensor suites can resolve various types of surrogate movement. Pressure transducers accurately record ambient wave conditions as well as changes in mean depth due to surrogate migration. Inertial motion units resolve munition accelerations for rolling and translational motion. Inertial motion unit data is used to estimate trajectory as well when coupled with mean depth and bathymetric data. Photocells, which measure ambient light, resolve munition burial as well as serve as proxies for surrounding environmental conditions such as suspended sediment and water depth. The presented project will continue to utilize and couple surrogate sensor data to resolve munition movement and burial under different conditions. Knowledge of munition migration helps focus UXO detection and recovery, conserving US military and coastal resources.

Bistatic scattering from submerged unexploded ordnance lying on a sediment.

PubMed

Bucaro, J A; Simpson, H; Kraus, L; Dragonette, L R; Yoder, T; Houston, B H

2009-11-01

The broadband bistatic target strengths (TSs) of two submerged unexploded ordnance (UXO) targets have been measured in the NRL sediment pool facility. The targets-a 5 in. rocket and a 155 mm projectile-were among the targets whose monostatic TSs were measured and reported previously by the authors. Bistatic TS measurements were made for 0 degrees (target front) and 90 degrees (target side) incident source directions, and include both backscattered and forward scattered echo angles over a complete 360 degrees with the targets placed proud of the sediment surface. For the two source angles used, each target exhibits two strong highlights: a backscattered specular-like echo and a forward scattered response. The TS levels of the former are shown to agree reasonably well with predictions, based on scattering from rigid disks and cylinders, while the levels of the latter with predictions from radar cross section models, based on simple geometric optics appropriately modified. The bistatic TS levels observed for the proud case provide comparable or higher levels of broadband TS relative to free-field monostatic measurements. It is concluded that access to bistatic echo information in operations aimed at detecting submerged UXO targets could provide an important capability.

Detection of Unexploded Ordnance Using Airborne LWIR Emissivity Signatures

DTIC Science & Technology

2015-11-25

glass and wood, are spectrally distinct and would not appear as false alarms. Index Terms— Hyperspectral, Long Wave Infrared , Emissivity, Target...hyperspectral; radar). Because of previous successes using thermal infrared bands for UXO [3, 4] and landmine detection [5], this paper aims at...potential false alarms. They included materials made of rubber , cardboard, metal, wood, glass and plastic (Figure 1). 2.2. Laboratory LWIR signature

Navy Pre-Deployment Training at Eglin AFB, Florida Final Environmental Assessment

DTIC Science & Technology

2004-02-10

Only-Radar ROW Rest of the World RUR Range Utilization Report SACEX Supporting Arms Coordination Exercise LIST OF ACRONYMS AND ABBREVIATIONS...Wildlife Service USGS U.S. Geological Survey UXO Unexploded Ordnance VOC Volatile Organic Compounds WHO World Health Organization Purpose and...Assessment While most deployments are scheduled long in advance, short-notice deployments often occur in response to world crises. The Atlantic Fleet’s

UXO Detector for Underwater Surveys Using Low-Frequency Sonar

DTIC Science & Technology

2015-06-01

Oude Waalsdorperweg 63 The Hague The Netherlands 9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES...remaining number of false alarms will be further reduced. The application of these two rules to the data shown in Figure 6-3, leads to removal of...Box 96864, 2509 JG The Hague , The Netherlands, +31 88 866 0902, alan.hunter@tno.nl Abstract: Detection of unexploded ordnance is challenging in the

Unexploded Ordnance (UXO) Data Analysis System (DAS). Environmental Quality Technology Program

DTIC Science & Technology

2009-09-01

is comprised of an EMI sensor, cesium (Cs) vapor magnetometer , fluxgate magnetometer , hand-held data acquisition computer, integrated power supply...Geometrics model 823A Cs vapor magnetometer . The fluxgate magnetometer is a Bartington model Mag-3MRN60, three- axis fluxgate magnetometer . The system...9. The ERDC hand-held Dual TFM/EMI with ArcSecond positioning system. During standard usage, the fluxgate magnetometer is used to provide the

Underwater (UW) Unexploded Ordnance (UXO) Multi-Sensor Data Base (MSDB) Collection

DTIC Science & Technology

2009-07-01

11 FIGURE 6 RTG SENSOR. FOUR SENSOR TRIADS ARE SHOWN, EACH WITH A 3-AXIS FLUXGATE MAGNETOMETER ...used by RTG to measure the gradients. Each triad includes a 3-axis fluxgate magnetometer and a set of feedback coils. The outputs of three triad...each with a 3-axis fluxgate magnetometer (internal, not clearly visible) and a set of 3 feedback coils. The upper triad 3-axis magnetometer

Subsurface Electromagnetic Induction Imaging for Unexploded Ordnance Detection

DTIC Science & Technology

2012-01-01

Baum, 1999; Pasion and Oldenburg, 2001). The EMI- response problem has been solved analytically for spheroids (Ao et al., 2002; Barrowes et al., 2004...components. We also have made explicit the fact that the polarizabilities are always positive ( Pasion et al., 2008); we impose this constraint in the...Wiley-Blackwell, Chichester, UK. Pasion , L.R., Oldenburg, D.W., 2001. A discrimination algorithm for UXO using time- domain electromagnetic induction

Detection of Buried Mines and Unexploded Ordnance (UXO)

DTIC Science & Technology

2007-04-20

http://www.apopo.org/newsite/content/index.htm Ref-3 Block, M., R. Medina , and R. Albanese. Analysis of data determining whether European honey...News Service, September 30. http://www.purdue.edu/UNS/html4ever/2005/050930.Cooks.explosives.html Brannon, James. M., Patrick Deliman, Carlos Ruiz...James. M., Patrick Deliman, Carlos Ruiz, Cynthia Price, Mohammed Qasim, Jeffrey A. Gerald, Charolett Hayes, and Sally Yost. 1999. HMX adsorption and TNT

Practical UXO Classification: Enhanced Data Processing Strategies for Technology Transition - Fort Ord: Dynamic and Cued Metalmapper Processing and Classification

DTIC Science & Technology

2017-06-06

OMB No. 0704-0188 Public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for...Geophysical Mapping, Electromagnetic Induction, Instrument Verification Strip, Time Domain Electromagnetic, Unexploded Ordnance 16. SECURITY...Munitions Response QA Quality Assurance QC Quality Control ROC Receiver Operating Characteristic RTK Real- time Kinematic s Second SNR

Magnetic STAR technology for real-time localization and classification of unexploded ordnance and buried mines

NASA Astrophysics Data System (ADS)

Wiegert, R. F.

2009-05-01

A man-portable Magnetic Scalar Triangulation and Ranging ("MagSTAR") technology for Detection, Localization and Classification (DLC) of unexploded ordnance (UXO) has been developed by Naval Surface Warfare Center Panama City Division (NSWC PCD) with support from the Strategic Environmental Research and Development Program (SERDP). Proof of principle of the MagSTAR concept and its unique advantages for real-time, high-mobility magnetic sensing applications have been demonstrated by field tests of a prototype man-portable MagSTAR sensor. The prototype comprises: a) An array of fluxgate magnetometers configured as a multi-tensor gradiometer, b) A GPS-synchronized signal processing system. c) Unique STAR algorithms for point-by-point, standoff DLC of magnetic targets. This paper outlines details of: i) MagSTAR theory, ii) Design and construction of the prototype sensor, iii) Signal processing algorithms recently developed to improve the technology's target-discrimination accuracy, iv) Results of field tests of the portable gradiometer system against magnetic dipole targets. The results demonstrate that the MagSTAR technology is capable of very accurate, high-speed localization of magnetic targets at standoff distances of several meters. These advantages could readily be transitioned to a wide range of defense, security and sensing applications to provide faster and more effective DLC of UXO and buried mines.

Evaluation of Unexploded Ordnance (UXO) Detection Technology at the Standardized UXO Test Sites Aberdeen and Yuma Proving Grounds

DTIC Science & Technology

2007-11-01

TTF Open Field (169) EM EM61MKII cart May. 2006 USGS Blind Grid (805) EM All TEM towed May. 2006 USGS Blind Grid (806) MAG TMGS towed 2.3-1 2.3...0.98 at YPG with a TMGS towed and an TM-4 sling system. f. The only ground penetrating radar system analyzed was demonstrated at the APG blind...MAG858/Cart(312) SCH/Hand(238) SCH/Hand(606) STOLS/Towed(293M) TM4/Sling(362) TM4/Sling(431) TMGS /Towed(806) EM61G822A/Cart(383D) STOLS/Towed(293D

Corrective Action Plan for Corrective Action Unit 453: Area 9 UXO Landfill, Tonopah Test Range, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bechtel Nevada

1998-09-30

This corrective action plan proposes the closure method for the area 9 unexploded Ordnance landfill, corrective action unit 453 located at the Tonopah Test Range. The area 9 UXO landfill consists of corrective action site no. 09-55-001-0952 and is comprised of three individual landfill cells designated as A9-1, A9-2, and A9-3. The three landfill cells received wastes from daily operations at area 9 and from range cleanups which were performed after weapons testing. Cell locations and contents were not well documented due to the unregulated disposal practices commonly associated with early landfill operations. However, site process knowledge indicates that themore » landfill cells were used for solid waste disposal, including disposal of UXO.« less

Intra-Inversion Filtering for Use of Magnetic Fields to Locate and Characterize Magnetic Dipoles for Unexploded Ordnance (UXO) Cleanup

DTIC Science & Technology

2007-02-26

IIGE Intra-Inversion Gradient Estimation JPG Jefferson Proving Ground (Indiana); www.jpgbrac.com MTADS Multi- sensor Towed Array Detection...wherein the Statement of Need sought development of algorithms to exploit data from current state-of-the-art geophysical sensors and advanced sensors ...profile direction using an array of magnetometers as in the Multi- sensor Towed Array Detection System (MTADS). In most instances, such data may be

Small threat and contraband detection with TNA-based systems.

PubMed

Shaw, T J; Brown, D; D'Arcy, J; Liu, F; Shea, P; Sivakumar, M; Gozani, T

2005-01-01

The detection of small threats, such as explosives, drugs, and chemical weapons, concealed or encased in surrounding material, is a major concern in areas from security checkpoints to UneXploded Ordnance (UXO) clearance. Techniques such as X-ray and trace detection are often ineffectual in these applications. Thermal neutron analysis (TNA) provides an effective method for detecting concealed threats. This paper shows the effectiveness of Ancore's SPEDS, based on TNA, in detecting concealed liquid threats and differentiating live from inert mortar shells.

Demonstration of Airborne Electromagnetic Systems for Detection and Characterization of Unexploded Ordnance at the Badlands Bombing Range, South Dakota. Revision 3

DTIC Science & Technology

2004-08-01

base station Attitude Measurement Ashtech ADU-2 Bartington MAG03ML7ONT 3-axis fluxgate magnetometer , Navigation Picodas PNAV100 Model P141-E Real...BBR Test Grid, horizontal difference (outer coil minus scaled inner coil). 46 22 Analytic signal derived from ground-based magnetometer bottom...one meter over UXO-contaminated terrain. As with the magnetic systems, GPS and laser altimetry provide precise positioning to within a few tens of

Joint Diagonalization Applied to the Detection and Discrimination of Unexploded Ordnance

DTIC Science & Technology

2012-08-01

center (Das et al., 1990; Barrow and Nelson, 2001; Bell et al., 2001; Pasion and Oldenburg , 2001; Zhang et al., 2003; Smith and Mor- rison, 2004; Tarokh et...matrix for the complete transmitter/receiver ar- ray by tiling all the Nr × Nt available samples of expression 5: S ¼ GscUlΛ̇lUTl ðGprÞT...L. R., and D. W. Oldenburg , 2001, A discrimination algorithm for UXO using time-domain electromagnetics: Journal of Environmental and Engineering

Numerical modeling of higher order magnetic moments in UXO discrimination

USGS Publications Warehouse

Sanchez, V.; Yaoguo, L.; Nabighian, M.N.; Wright, D.L.

2008-01-01

The surface magnetic anomaly observed in unexploded ordnance (UXO) clearance is mainly dipolar, and consequently, the dipole is the only magnetic moment regularly recovered in UXO discrimination. The dipole moment contains information about the intensity of magnetization but lacks information about the shape of the target. In contrast, higher order moments, such as quadrupole and octupole, encode asymmetry properties of the magnetization distribution within the buried targets. In order to improve our understanding of magnetization distribution within UXO and non-UXO objects and to show its potential utility in UXO clearance, we present a numerical modeling study of UXO and related metallic objects. The tool for the modeling is a nonlinear integral equation describing magnetization within isolated compact objects of high susceptibility. A solution for magnetization distribution then allows us to compute the magnetic multipole moments of the object, analyze their relationships, and provide a depiction of the anomaly produced by different moments within the object. Our modeling results show the presence of significant higher order moments for more asymmetric objects, and the fields of these higher order moments are well above the noise level of magnetic gradient data. The contribution from higher order moments may provide a practical tool for improved UXO discrimination. ?? 2008 IEEE.

UXO detection and identification based on intrinsic target polarizabilities: A case history

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, E.; Smith, J.T.; Morrison, H.F.

2008-07-15

Electromagnetic induction data parameterized in time dependent object intrinsic polarizabilities allow discrimination of unexploded ordnance (UXO) from false targets (scrap metal). Data from a cart-mounted system designed for discrimination of UXO with 20 mm to 155 mm diameters are used. Discrimination of UXO from irregular scrap metal is based on the principal dipole polarizabilities of a target. A near-intact UXO displays a single major polarizability coincident with the long axis of the object and two equal smaller transverse polarizabilities, whereas metal scraps have distinct polarizability signatures that rarely mimic those of elongated symmetric bodies. Based on a training data setmore » of known targets, object identification was made by estimating the probability that an object is a single UXO. Our test survey took place on a military base where both 4.2-inch mortar shells and scrap metal were present. The results show that we detected and discriminated correctly all 4.2-inch mortars, and in that process we added 7%, and 17%, respectively, of dry holes (digging scrap) to the total number of excavations in two different survey modes. We also demonstrated a mode of operation that might be more cost effective than the current practice.« less

Acquisition and processing of advanced sensor data for ERW and UXO detection and classification

NASA Astrophysics Data System (ADS)

Schultz, Gregory M.; Keranen, Joe; Miller, Jonathan S.; Shubitidze, Fridon

2014-06-01

The remediation of explosive remnants of war (ERW) and associated unexploded ordnance (UXO) has seen improvements through the injection of modern technological advances and streamlined standard operating procedures. However, reliable and cost-effective detection and geophysical mapping of sites contaminated with UXO such as cluster munitions, abandoned ordnance, and improvised explosive devices rely on the ability to discriminate hazardous items from metallic clutter. In addition to anthropogenic clutter, handheld and vehicle-based metal detector systems are plagued by natural geologic and environmental noise in many post conflict areas. We present new and advanced electromagnetic induction (EMI) technologies including man-portable and towed EMI arrays and associated data processing software. While these systems feature vastly different form factors and transmit-receive configurations, they all exhibit several fundamental traits that enable successful classification of EMI anomalies. Specifically, multidirectional sampling of scattered magnetic fields from targets and corresponding high volume of unique data provide rich information for extracting useful classification features for clutter rejection analysis. The quality of classification features depends largely on the extent to which the data resolve unique physics-based parameters. To date, most of the advanced sensors enable high quality inversion by producing data that are extremely rich in spatial content through multi-angle illumination and multi-point reception.

Experiences with unexploded ordnance discrimination using magnetometry at a live-site in Montana

NASA Astrophysics Data System (ADS)

Billings, Stephen; Youmans, Clifton

2007-03-01

Advanced discrimination methods and careful optimization of operational procedures are critical for efficient remediation of unexploded ordnance (UXO) contaminated sites. In this paper, we report on our experiences with a 200 acre magnetic survey that was collected and processed under production survey conditions at Chevallier Ranch, Montana. All anomalies with fitted moments above 0.05 Am 2 were excavated. During the survey the magnetic remanence metric was predicted but not used to guide the discrimination. The retrospective analysis presented here reveals that discrimination using remanence would have significantly reduced the total number of anomalies (with good dipolar fits) that needed to be excavated, from 524 to 290 while still recovering all 69 UXO. The false alarm rate (FAR = number of non-UXOs excavated divided / number of UXO found) was reduced from 6.3 to 2.9. At a cut-off of 75% remanence, 77% of anomalies due to shrapnel and metallic debris and 64% of geological anomalies were rejected. Geological anomalies due to variations in magnetite concentration introduced a significant human-element into the interpretation process. Three different interpreters added a total of 305 additional anomalies that were not fit with a dipole model and which were later found to be non-UXO. Between 40 and 50% of anomalies picked by the two relatively inexperienced interpreters who analyzed the data turned out to be geology, as compared to 14% for an experienced interpreter. Critical analysis of results, operator training and feedback from the UXO technicians validating the anomaly are essential components towards improving the quality and consistency of the anomaly interpretations. This is consistent with the tenants of Total Quality Management (TQM). We compare the actual FAR that resulted during the survey when there was little feedback between UXO technician validation results, to a hypothetical result that could have been achieved had there been a constant feedback system in place at the onset of operations. Feedback would have significantly reduced the number of geological anomalies and decreased the FAR from 10.7 to 4.0. The hypothetical results presented here demonstrate the value of using TQM principles to guide the UXO remediation process. They further show that improvements in the efficiency and costs of UXO remediation require both technological advances and operational optimization of the technology when implemented in a production setting. Furthermore, by treating geophysical modeling and UXO validation as separate entities, both with respect to contracting and operational reporting, there is little incentive for the geophysicist to leave an anomaly off the dig-sheet. Only potential negative consequences will result if that anomaly is later found to be a UXO. An incentive based mechanism that rewards the geophysicist for reductions in follow-on costs would have a strong potential to reduce the number of unnecessary excavations, and hence reduce the total cost of the UXO remediation effort.

Version 2.0 Visual Sample Plan (VSP): UXO Module Code Description and Verification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Richard O.; Wilson, John E.; O'Brien, Robert F.

2003-05-06

The Pacific Northwest National Laboratory (PNNL) is developing statistical methods for determining the amount of geophysical surveys conducted along transects (swaths) that are needed to achieve specified levels of confidence of finding target areas (TAs) of anomalous readings and possibly unexploded ordnance (UXO) at closed, transferring and transferred (CTT) Department of Defense (DoD) ranges and other sites. The statistical methods developed by PNNL have been coded into the UXO module of the Visual Sample Plan (VSP) software code that is being developed by PNNL with support from the DoD, the U.S. Department of Energy (DOE, and the U.S. Environmental Protectionmore » Agency (EPA). (The VSP software and VSP Users Guide (Hassig et al, 2002) may be downloaded from http://dqo.pnl.gov/vsp.) This report describes and documents the statistical methods developed and the calculations and verification testing that have been conducted to verify that VSPs implementation of these methods is correct and accurate.« less

An exploratory study of the perceived impact of health problems of landmine/UXO victims versus another disability group

PubMed Central

2012-01-01

Background The purpose of this exploratory study is to pilot a biopsychosocial instrument called the Perceived Impact of Problem Profile (PIPP) on a cohort of landmine/Unexploded Ordnance (UXO) victims with lower limb disability versus a cohort of persons with similar disability due to other trauma or medical causes. The aim is to provide greater understanding of the psychosocial impact of landmine/UXO injury to inform victim assistance a interventions within Lao PDR. Methods This study employs a mixed methods design, which involved piloting the PIPP instrument through an interviewer administered questionnaire and demographic questionnaire. Fifty one participants were interviewed in both urban and rural locations within Lao PDR. Results An analysis of the data reveals significant differences in perceived impact for pain, anxiety and how recently the injury/illness occurred. Both groups complained of high levels of anxiety and depression; landmine/UXO victims who complained of anxiety and depression reported a much greater impact on life satisfaction and mood. Conclusion The perceived impact of the disability is greatest on psychosocial factors for both cohorts, but especially in landmine/UXO victims emphasising the need to focus on improving psychosocial interventions for landmine/UXO victims within Victim assistance programmes in Lao PDR. PMID:23016958

Statistical Methods and Tools for Uxo Characterization (SERDP Final Technical Report)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsipher, Brent A.; Gilbert, Richard O.; Wilson, John E.

2004-11-15

The Strategic Environmental Research and Development Program (SERDP) issued a statement of need for FY01 titled Statistical Sampling for Unexploded Ordnance (UXO) Site Characterization that solicited proposals to develop statistically valid sampling protocols for cost-effective, practical, and reliable investigation of sites contaminated with UXO; protocols that could be validated through subsequent field demonstrations. The SERDP goal was the development of a sampling strategy for which a fraction of the site is initially surveyed by geophysical detectors to confidently identify clean areas and subsections (target areas, TAs) that had elevated densities of anomalous geophysical detector readings that could indicate the presencemore » of UXO. More detailed surveys could then be conducted to search the identified TAs for UXO. SERDP funded three projects: those proposed by the Pacific Northwest National Laboratory (PNNL) (SERDP Project No. UXO 1199), Sandia National Laboratory (SNL), and Oak Ridge National Laboratory (ORNL). The projects were closely coordinated to minimize duplication of effort and facilitate use of shared algorithms where feasible. This final report for PNNL Project 1199 describes the methods developed by PNNL to address SERDP's statement-of-need for the development of statistically-based geophysical survey methods for sites where 100% surveys are unattainable or cost prohibitive.« less

Applied Behavior Analysis Is Ideal for the Development of a Land Mine Detection Technology Using Animals

PubMed Central

Jones, B. M

2011-01-01

The detection and subsequent removal of land mines and unexploded ordnance (UXO) from many developing countries are slow, expensive, and dangerous tasks, but have the potential to improve the well-being of millions of people. Consequently, those involved with humanitarian mine and UXO clearance are actively searching for new and more efficient detection technologies. Remote explosive scent tracing (REST) using trained dogs has the potential to be one such technology. However, details regarding how best to train, test, and deploy dogs in this role have never been made publicly available. This article describes how the key characteristics of applied behavior analysis, as described by Baer, Wolf and Risley (1968, 1987), served as important objectives for the research and development of the behavioral technology component of REST while the author worked in humanitarian demining. PMID:22532731

Applied behavior analysis is ideal for the development of a land mine detection technology using animals.

PubMed

Jones, B M

2011-01-01

The detection and subsequent removal of land mines and unexploded ordnance (UXO) from many developing countries are slow, expensive, and dangerous tasks, but have the potential to improve the well-being of millions of people. Consequently, those involved with humanitarian mine and UXO clearance are actively searching for new and more efficient detection technologies. Remote explosive scent tracing (REST) using trained dogs has the potential to be one such technology. However, details regarding how best to train, test, and deploy dogs in this role have never been made publicly available. This article describes how the key characteristics of applied behavior analysis, as described by Baer, Wolf and Risley (1968, 1987), served as important objectives for the research and development of the behavioral technology component of REST while the author worked in humanitarian demining.

Performance metrics for state-of-the-art airborne magnetic and electromagnetic systems for mapping and detection of unexploded ordnance

NASA Astrophysics Data System (ADS)

Doll, William E.; Bell, David T.; Gamey, T. Jeffrey; Beard, Les P.; Sheehan, Jacob R.; Norton, Jeannemarie

2010-04-01

Over the past decade, notable progress has been made in the performance of airborne geophysical systems for mapping and detection of unexploded ordnance in terrestrial and shallow marine environments. For magnetometer systems, the most significant improvements include development of denser magnetometer arrays and vertical gradiometer configurations. In prototype analyses and recent Environmental Security Technology Certification Program (ESTCP) assessments using new production systems the greatest sensitivity has been achieved with a vertical gradiometer configuration, despite model-based survey design results which suggest that dense total-field arrays would be superior. As effective as magnetometer systems have proven to be at many sites, they are inadequate at sites where basalts and other ferrous geologic formations or soils produce anomalies that approach or exceed those of target ordnance items. Additionally, magnetometer systems are ineffective where detection of non-ferrous ordnance items is of primary concern. Recent completion of the Battelle TEM-8 airborne time-domain electromagnetic system represents the culmination of nearly nine years of assessment and development of airborne electromagnetic systems for UXO mapping and detection. A recent ESTCP demonstration of this system in New Mexico showed that it was able to detect 99% of blind-seeded ordnance items, 81mm and larger, and that it could be used to map in detail a bombing target on a basalt flow where previous airborne magnetometer surveys had failed. The probability of detection for the TEM-8 in the blind-seeded study area was better than that reported for a dense-array total-field magnetometer demonstration of the same blind-seeded site, and the TEM-8 system successfully detected these items with less than half as many anomaly picks as the dense-array total-field magnetometer system.

Incorporating advanced EMI technologies in operational munitions characterization surveys

NASA Astrophysics Data System (ADS)

Miller, Jonathan S.; Shubiditze, Fridon; Pasion, Leonard; Schultz, Gregory; Chung, Heesoo

2011-06-01

The presence of unexploded ordnance (UXO), discarded military munitions (DMM), and munitions constituents (MC) at both active and formerly used defense sites (FUDS) has created a necessity for production-level efforts to remove these munitions and explosives of concern (MEC). Ordnance and explosives (OE) and UXO removal operations typically employ electromagnetic induction (EMI) or magnetometer surveys to identify potential MEC hazards in previously determined areas of interest. A major cost factor in these operations is the significant allocation of resources for the excavation of harmless objects associated with fragmentation, scrap, or geological clutter. Recent advances in classification and discrimination methodologies, as well as the development of sensor technologies that fully exploit physics-based analysis, have demonstrated promise for significantly reducing the false alarm rate due to MEC related clutter. This paper identifies some of the considerations for and the challenges associated with implementing these discrimination methodologies and advanced sensor technologies in production-level surveys. Specifically, we evaluate the implications of deploying an advanced multi-axis EMI sensor at a variety of MEC sites, the discrimination methodologies that leverage the data produced by this sensor, and the potential for productivity increase that could be realized by incorporating this advanced technology as part of production protocol.

Magnetic sensor technology for detecting mines, UXO, and other concealed security threats

NASA Astrophysics Data System (ADS)

Czipott, Peter V.; Iwanowski, Mark D.

1997-01-01

Magnetic sensors have been the sensor of choice in the detection and classification of buried mines and unexploded ordnance (UXO), both on land and underwater, Quantum Magnetics (QM), together with its research partner IBM, have developed a variety of advanced, very high sensitivity superconducting and room temperature magnetic sensors to meet military needs. This work has led to the development and utilization of a three-sensor gradiometer (TSG) patented by IBM, which cannot only detect, but also localize mines and ordnance. QM is also working with IBM and the U.S. Navy to develop an advanced superconducting gradiometer for buried underwater mine detection. The ability to both detect and classify buried non-metallic mines is virtually impossible with existing magnetic sensors. To solve this problem, Quantum Magnetics, building on work of the Naval Research Laboratory (NRL), is pioneering work in the development of quadrupole resonance (QR) methods which can be used to detect the explosive material directly. Based on recent laboratory work done at QM and previous work done in the U.S., Russia and the United Kingdom, we are confident that QR can be effectively applied to the non-metallic mine identification problem.

Automatic classification of unexploded ordnance applied to Spencer Range live site for 5x5 TEMTADS sensor

NASA Astrophysics Data System (ADS)

Sigman, John B.; Barrowes, Benjamin E.; O'Neill, Kevin; Shubitidze, Fridon

2013-06-01

This paper details methods for automatic classification of Unexploded Ordnance (UXO) as applied to sensor data from the Spencer Range live site. The Spencer Range is a former military weapons range in Spencer, Tennessee. Electromagnetic Induction (EMI) sensing is carried out using the 5x5 Time-domain Electromagnetic Multi-sensor Towed Array Detection System (5x5 TEMTADS), which has 25 receivers and 25 co-located transmitters. Every transmitter is activated sequentially, each followed by measuring the magnetic field in all 25 receivers, from 100 microseconds to 25 milliseconds. From these data target extrinsic and intrinsic parameters are extracted using the Differential Evolution (DE) algorithm and the Ortho-Normalized Volume Magnetic Source (ONVMS) algorithms, respectively. Namely, the inversion provides x, y, and z locations and a time series of the total ONVMS principal eigenvalues, which are intrinsic properties of the objects. The eigenvalues are fit to a power-decay empirical model, the Pasion-Oldenburg model, providing 3 coefficients (k, b, and g) for each object. The objects are grouped geometrically into variably-sized clusters, in the k-b-g space, using clustering algorithms. Clusters matching a priori characteristics are identified as Targets of Interest (TOI), and larger clusters are automatically subclustered. Ground Truths (GT) at the center of each class are requested, and probability density functions are created for clusters that have centroid TOI using a Gaussian Mixture Model (GMM). The probability functions are applied to all remaining anomalies. All objects of UXO probability higher than a chosen threshold are placed in a ranked dig list. This prioritized list is scored and the results are demonstrated and analyzed.

Multiscale Structure of UXO Site Characterization: Spatial Estimation and Uncertainty Quantification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ostrouchov, George; Doll, William E.; Beard, Les P.

2009-01-01

Unexploded ordnance (UXO) site characterization must consider both how the contamination is generated and how we observe that contamination. Within the generation and observation processes, dependence structures can be exploited at multiple scales. We describe a conceptual site characterization process, the dependence structures available at several scales, and consider their statistical estimation aspects. It is evident that most of the statistical methods that are needed to address the estimation problems are known but their application-specific implementation may not be available. We demonstrate estimation at one scale and propose a representation for site contamination intensity that takes full account of uncertainty,more » is flexible enough to answer regulatory requirements, and is a practical tool for managing detailed spatial site characterization and remediation. The representation is based on point process spatial estimation methods that require modern computational resources for practical application. These methods have provisions for including prior and covariate information.« less

Statistical Algorithms Accounting for Background Density in the Detection of UXO Target Areas at DoD Munitions Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matzke, Brett D.; Wilson, John E.; Hathaway, J.

2008-02-12

Statistically defensible methods are presented for developing geophysical detector sampling plans and analyzing data for munitions response sites where unexploded ordnance (UXO) may exist. Detection methods for identifying areas of elevated anomaly density from background density are shown. Additionally, methods are described which aid in the choice of transect pattern and spacing to assure with degree of confidence that a target area (TA) of specific size, shape, and anomaly density will be identified using the detection methods. Methods for evaluating the sensitivity of designs to variation in certain parameters are also discussed. Methods presented have been incorporated into the Visualmore » Sample Plan (VSP) software (free at http://dqo.pnl.gov/vsp) and demonstrated at multiple sites in the United States. Application examples from actual transect designs and surveys from the previous two years are demonstrated.« less

Modeling the tagged-neutron UXO identification technique using the Geant4 toolkit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou Y.; Mitra S.; Zhu X.

2011-10-16

It is proposed to use 14 MeV neutrons tagged by the associated particle neutron time-of-flight technique (APnTOF) to identify the fillers of unexploded ordnances (UXO) by characterizing their carbon, nitrogen and oxygen contents. To facilitate the design and construction of a prototype system, a preliminary simulation model was developed, using the Geant4 toolkit. This work established the toolkit environment for (a) generating tagged neutrons, (b) their transport and interactions within a sample to induce emission and detection of characteristic gamma-rays, and (c) 2D and 3D-image reconstruction of the interrogated object using the neutron and gamma-ray time-of-flight information. Using the modeling,more » this article demonstrates the novelty of the tagged-neutron approach for extracting useful signals with high signal-to-background discrimination of an object-of-interest from that of its environment. Simulations indicated that an UXO filled with the RDX explosive, hexogen (C{sub 3}H{sub 6}O{sub 6}N{sub 6}), can be identified to a depth of 20 cm when buried in soil.« less

Development of an instrument for non-destructive identification of Unexploded Ordnance using tagged neutrons - a proof of concept study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitra, S.; Dioszegi, I.

2011-10-23

Range clearance operations at munitions testing grounds must discriminate Unexploded Ordnance (UXO) from clutter items and distinguish UXO filled with High Explosives (HE) from those with inert fillers. Non-destructive technologies are thus necessary for the cost-effective disposal of UXO during remediation of such sites. The only technique showing promise so far for the non-destructive elemental characterization of UXO fillers utilizes neutron interactions with the material to detect carbon (C), nitrogen (N) and oxygen (O) which have unique ratios in HE. However, several unresolved issues hinder the wide application of this potentially very suitable technique. The most important one is thatmore » neutrons interact with all surrounding matter in addition to the interrogated material, leading to a very high gamma-ray background in the detector. Systems requiring bulky shielding and having poor signal-to-noise ratios (SNRs) for measuring elements are unsuitable for field deployment. The inadequacies of conventional neutron interrogation methods are overcome by using the tagged-neutron approach, and the availability of compact sealed neutron generators exploiting this technique offers field deployment of non-intrusive measurement systems for detecting threat materials, like explosives and drugs. By accelerating deuterium ions into a tritium target, the subsequent fusion reaction generates nearly back-to-back emissions of neutrons and alpha particles of energy 14.1 and 3.5 MeV respectively. A position-sensitive detector recognizes the associated alpha particle, thus furnishing the direction of the neutron. The tagged neutrons interact with the nuclei of the interrogated object, producing element-specific prompt gamma-rays that the gamma detectors recognize. Measuring the delay between the detections of the alpha particle and the gamma-ray determines where the reaction occurred along the axis of the neutron beam (14.1 MeV neutrons travel at 5 cm/nanosecond, while gamma rays cover 30 cm/nanosecond). The main advantage of the technique is its ability to simultaneously provide 2D and 3D imaging of objects and their elemental composition. This work reports on the efficacy of using 14 MeV neutrons tagged by the associated particle neutron time-of-flight technique (APnTOF) to extract neutron induced characteristic gamma-rays from an object-of-interest with high SNR and without interference from nearby clutter.« less

The lasting legacy of war: epidemiology of injuries from landmines and unexploded ordnance in Afghanistan, 2002-2006.

PubMed

Bilukha, Oleg O; Brennan, Muireann; Anderson, Mark

2008-01-01

Due to several decades of armed conflict and civil unrest, Afghanistan is one of the countries most affected by landmines and unexploded ordnance worldwide. The study was performed to assess the magnitude of injuries due to landmines and unexploded ordnance in Afghanistan during 2002-2006 and to describe epidemiological patterns and potential risk factors for these events. Surveillance data including 5,471 injuries caused by landmines and unexploded ordnance in Afghanistan during 2002-2006 were analyzed. The International Committee of the Red Cross collects data on such injuries from 490 reporting health facilities and volunteers throughout the country. These surveillance data were used to describe injury trends, victim demographics, injury types, risk behaviors, and explosive types related to landmine and unexploded ordnance accidents. The largest number of injuries (1,706) occurred in 2002. The number declined sharply to 1,049 injuries in 2003, and remained relatively stable with slight decline thereafter. Overall, 92% of victims were civilians, 91% were males, and 47% were children <18 years of age. The case-fatality ratio was 17%. Approximately 50% of all injuries were caused by unexploded ordnance and 42% by landmines. Among children, 65% of injuries were caused by unexploded ordnance and only 27% by landmines, whereas in adults, most injuries (56%) were caused by landmines. The most common risk behaviors among children were tending animals, playing, and tampering with explosive devices. In adults, most common risk behaviors were traveling, performing activities of economic necessity, and tampering with explosives. Twenty-eight percent of the surviving victims who received mine awareness training and 2% of those who did not receive such training reported that the area where event occurred was marked. The large number of injuries and high proportion of child victims suggest that clearance and risk education activities fall short of achieving their goals, and must be substantially improved or expanded. Especially concerning is the high proportion of injuries caused by unexploded ordnance, and the high number of injuries sustained while tampering with explosive devices. Because unexploded ordnance is more visible than are landmines, and ordnance-contaminated areas are cheaper to clear than are minefields, these injuries are highly preventable and should be a priority for clearance and risk education efforts.

Operational field evaluation of the PAC-MAG man-portable magnetometer array

NASA Astrophysics Data System (ADS)

Keranen, Joe; Topolosky, Zeke; Schultz, Gregory; Miller, Jonathan

2013-06-01

Detection and discrimination of unexploded ordnance (UXO) in areas of prior conflict is of high importance to the international community and the United States government. For humanitarian applications, sensors and processing methods need to be robust, reliable, and easy to train and implement using indigenous UXO removal personnel. This paper describes system characterization, system testing, and a continental United States (CONUS) Operational Field Evaluations (OFE) of the PAC-MAG man-portable UXO detection system. System testing occurred at a government test facility in June, 2010 and December, 2011 and the OFE occurred at the same location in June, 2012. NVESD and White River Technologies personnel were present for all testing and evaluation. The PAC-MAG system is a manportable magnetometer array for the detection and characterization of ferrous UXO. System hardware includes four Cesium vapor magnetometers for detection, a Real-time Kinematic Global Position System (RTK-GPS) for sensor positioning, an electronics module for merging array data and WiFi communications and a tablet computer for transmitting and logging data. An odometer, or "hipchain" encoder, provides position information in GPS-denied areas. System software elements include data logging software and post-processing software for detection and characterization of ferrous anomalies. The output of the post-processing software is a dig list containing locations of potential UXO(s), formatted for import into the system GPS equipment for reacquisition of anomalies. Results from system characterization and the OFE will be described.

Seen but not heard: injuries and deaths from landmines and unexploded ordnance in Chechnya, 1994-2005.

PubMed

Bilukha, Oleg O; Brennan, Muireann; Anderson, Mark; Tsitsaev, Zaur; Murtazaeva, Eliza; Ibragimov, Ramzan

2007-01-01

Due to more than a decade of armed conflict and civil unrest, Chechnya is among the regions most affected by landmines and unexploded ordnance worldwide. The study was performed to assess the magnitude of injuries and deaths due to landmines and unexploded ordnance in Chechnya between 1994 and 2005 and to describe epidemiologic patterns and risk factors for these events. Surveillance data that included 3,021 civilian non-combatants injured by landmines and unexploded ordnance in Chechnya during 1994-2005 were analyzed. Local non-governmental organizations in collaboration with the United Nations Children's Fund conducted victim data collection using trained staff to interview victims or their families. Surveillance data were used to describe injury trends, victim demographics, injury types, risk behaviors, and types of explosives related to landmine and unexploded ordnance events. The largest number of injuries occurred in 2000 (716, injury rate 6.6 per 10,000) and 2001 (640, injury rate 5.9 per 10,000). One-quarter of all victims were younger than 18 years, and 19% were females. The case-fatality rate was 23%. Approximately 40% of victims were injured by landmines, 30% by unexploded ordnance, and 7% by booby traps. A large proportion of children and adults were injured while traveling or performing activities of economic necessity; 29% of children were injured while tampering with explosives or playing in a contaminated area. The proportion of victims with lower limb amputations was similar among children and adults (14% and 17%, respectively), whereas the proportion ofvictims with upper limb amputations was three times higher in children than in adults (12% and 4%, respectively). Most accidents that occurred while the victim was traveling or performing activities of economic necessity were caused by landmines, while most accidents that occurred while the victim was playing near an explosive device or tampering with it were caused by unexploded ordnance. Civilians in Chechnya experienced the highest rates of injury from landmines and unexploded ordnance ever documented, 10 times higher than injury rates reported from such highly affected countries as Afghanistan, Angola, or Cambodia. Urgent efforts to identify, mark, and clear mined areas and/or areas contaminated with unexploded ordnance are needed to prevent further civilian injuries and deaths.

Computational Fluid Dynamics Modeling of Submerged Objects Under Unidirectional and Oscillatory Flows.

NASA Astrophysics Data System (ADS)

Fytanidis, D. K.; Wu, H.; Landry, B. J.; Garcia, M. H.

2017-12-01

Abandoned Unexploded Ordnances (UXOs) from wartime events, accidents, training or other military activities can be found in coastal environments. While the interest for these hazardous submerged objects is increased, there are still existing knowledge gaps regarding the mechanisms of incipient motion and flow behavior around UXOs lying on the seafloor. Numerical modeling of flow around near bed placed UXOs is conducted for unidirectional and oscillatory flow conditions using Computational Fluid Dynamics techniques. The Reynolds-Averaged Navier-Stokes (RANS) approach is used to simulate the complex turbulent flow field around UXOs. The numerical results are compared with two-dimensional Particle Image Velocimetry measurements from experiments conducted in unidirectional and oscillatory flow facilities within the Ven Te Chow Hydrosystems Laboratory to evaluate the accuracy of the applied RANS-based solver. Realistic boundary conditions are imposed in the numerical models to mimic the experimental conditions in the laboratory facilities. The comparison between the numerical results and the experimental data agrees well. In addition, the effect of the angle of attack on the forces that UXOs experience is examined. Numerical results suggest that the orientation of UXOs with respect to the mean flow is an important parameter for incipient motion under critical flow conditions which is in agreement with prior laboratory experimental results regarding the identification of critical flow conditions for the initiation of motion of UXOs. Finally, an extensive parametric analysis is conducted to evaluate the effect of the maximum current velocity and wave characteristics (maximum velocity and period) on the flow forces and the mean flow pattern around the objects.

PELAN: a pulsed neutron portable probe for UXO and land mine identification

NASA Astrophysics Data System (ADS)

Vourvopoulos, George; Womble, Phillip C.; Paschal, Jonathon

2000-12-01

There has been much work increasing the sensitivity of detecting metallic objects in soils and other environments. This has lead to a problem in discriminating unexploded ordnance (UXO) and landmines form other metallic clutter. PELAN is a small portable system for the detection of explosives. PELAN weights less than 45 kg and is man portable. It is based on the principle that explosives and other contraband contain various chemical elements such as H, C, N, O, etc. in quantities and ratios that differentiate them from other innocuous substances. The pulsed neutrons are produced with a 14 MeV neutron generator. Separate gamma-ray spectra form fast neutron, thermal neutron and activation reactions are accumulated and analyzed to determine elemental content. The data analysis is performed in an automatic manner and a result of whether a threat is present is returned to the operator. PELAN has successfully undergone field demonstrations for explosive detection. In this paper, we will discuss the application of PELAN to the problem of differentiating threats from metallic clutter.

The legacy of war: an epidemiological study of cluster weapon and land mine accidents in Quang Tri Province, Vietnam.

PubMed

Phung, Tran Kim; Le, Viet; Husum, Hans

2012-07-01

The study examines the epidemiology of cluster weapon and land mine accidents in Quang Tri Province since the end of the Vietnam War. The province is located just south of the demarcation line and was the province most affected during the war. In 2009, a cross sectional household study was conducted in all nine districts of the province. During the study period of 1975-2009, 7,030 persons in the study area were exposed to unexploded ordnances (UXO) or land mine accidents, or 1.1% of the provincial population. There were 2,620 fatalities and 4,410 accident survivors. The study documents that the main problem is cluster weapons and other unexploded ordnances; only 4.3% of casualties were caused by land mines. The legacy of the war affects poor people the most; the accident rate was highest among villagers living in mountainous areas, ethnic minorities, and low-income families. The most common activities leading to the accidents were farming (38.6%), collecting scrap metal (11.2%), and herding of cattle (8.3%). The study documents that the people of the Quang Tri Province until this day have suffered heavily due to the legacy of war. Mine risk education programs should account for the epidemiological findings when future accident prevention programs are designed to target high-risk areas and activities.

Epidemiological Study of Child Casualties of Landmines and Unexploded Ordnances: A National Study from Iran.

PubMed

Mousavi, Batool; Soroush, Mohammad Reza; Masoumi, Mehdi; Khateri, Shahriar; Modirian, Ehsan; Shokoohi, Hamid; Fatemi, Mohammad Javad; Ali Hematti, Mohammad; Soroush, Mansour; Ghassemi-Broumand, Mohammad; Rassafiani, Mehdi; Allami, Mostafa; Nouri, Farshad; Yavari, Amir; Ganjparvar, Zohreh; Kamyab, Mojtaba; Mirsadeghi, Seyed Abbas

2015-10-01

Despite landmine-risk education programs and extensive demining activities on the Western border of Iran, landmines and unexploded ordnance (UXOs) still cause civilian and child casualties three decades after the Iraq-Iran war (1980-1988). The objective of this study was to understand the epidemiological patterns and risk factors of injury in child casualties of landmines and UXOs in Western and Southwestern Iran. Children who were 18 years old or younger at the time of study and who sustained injuries from landmines and UXOs were identified through a search at the Iranian National Veterans Registry. These children participated in a 5-day gathering. The information on socioeconomic status, health-related issues, quality of life, health care utilization, and clinical profiles concerning the landmine and UXO injuries were collected. The method of data collection consisted of three component surveys: health interview, social survey, and medical examinations. Social surveys and health interviews were conducted in a face-to-face method by utilizing a questionnaire consisting of 39 questions addressing household and individual components, including information on time and type of injuries, physical activity, mental health, and quality of life. A comprehensive team of physicians in different subspecialties evaluated and examined children to assess the current medical and psychiatric conditions and physical activity, and recommended and arranged further medical, rehabilitation, or surgical planning. Seventy-eight child casualties were identified and participated in the study. The mean age of the participants at the time of study was 16.11 years old (SD=2 years). The mean age of victims at the time of injury was 8.2 years (SD=3.12 years; ranged from 2 to 15 years old). Sixty-seven (85.9%) of the children were male. Provinces of Kurdistan and Kermanshah had the highest number of casualties, with a total number of 54 children (68.3%). Eighty percent of the injuries were caused by landmines, and UXO explosions were reported in 20% of the cases. Overall, 24 children (30%) had received some landmine-risk education before or after the events. Sixty percent of the explosions had happened in the morning between 9:00 am and 12:00 pm. Playing and grazing livestock were the most prevalent activities/reasons at the time of injury, which were reported in 77% of the subjects. Sixty-three percent of incidents had multiple casualties and in only 13 explosions were the children the only victims of the explosion. The most prevalent injuries were amputations in 41 subjects (52.56%), followed by hearing loss in 23 subjects (29.5%). Amputations were more common in upper extremities (62%) than in lower extremities (38%). Landmines and UXOs comprise a significant safety hazard to the children living in the Western border of Iran decades after the Iraq-Iran War. The large number of injuries and lack of risk training among victims suggest that landmine cleanings and landmine-risk education should be age-specifically targeted and expanded substantially.

Large-Scale Laboratory Experiments of Initiation of Motion and Burial of Objects under Currents and Waves

NASA Astrophysics Data System (ADS)

Landry, B. J.; Wu, H.; Wenzel, S. P.; Gates, S. J.; Fytanidis, D. K.; Garcia, M. H.

2017-12-01

Unexploded ordnances (UXOs) can be found at the bottom of coastal areas as the residue of military wartime activities, training or accidents. These underwater objects are hazards for humans and the coastal environment increasing the need for addressing the knowledge gaps regarding the initiation of motion, fate and transport of UXOs under currents and wave conditions. Extensive experimental analysis was conducted for the initiation of motion of UXOs under various rigid bed roughness conditions (smooth PVC, pitted steel, marbles, gravels and bed of spherical particles) for both unidirectional and oscillatory flows. Particle image velocimetry measurements were conducted under both flow conditions to resolve the flow structure estimate the critical flow conditions for initiation of motion of UXOs. Analysis of the experimental observations shows that the geometrical characteristics of the UXOs, their properties (i.e. volume, mass) and their orientation with respect to the mean flow play an important role on the reorientation and mobility of the examined objects. A novel unified initiation of motion diagram is proposed using an effective/unified hydrodynamic roughness and a new length scale which includes the effect of the projected area and the bed-UXO contact area. Both unidirectional and oscillatory critical flow conditions collapsed into a single dimensionless diagram highlighting the importance and practical applicability of the proposed work. In addition to the rigid bed experiments, the burial dynamics of proud UXOs on a mobile sand bed were also examined. The complex flow-bedform-UXOs interactions were evaluated which highlighted the effect of munition density on burial rate and final burial depth. Burial dynamics and mechanisms for motion were examined for various UXOs types, and results show that, for the case of the low density UXOs under energetic conditions, lateral transport coexists with burial. Prior to burial, UXO re-orientation was also observed depending on the geometric characteristics of the objects.

ALLTEM UXO detection and discrimination

USGS Publications Warehouse

Asch, T.H.; Wright, D.L.; Moulton, C.W.; Irons, T.P.; Nabighian, M.N.

2008-01-01

ALLTEM is a multi-axis electromagnetic induction system designed for unexploded ordnance (UXO) applications. It uses a continuous triangle-wave excitation and provides good late-time signal-to-noise ratio (SNR) especially for ferrous targets. Multi-axis transmitter (Tx) and receiver (Rx) systems such as ALLTEM provide a richer data set from which to invert for the target parameters required to distinguish between clutter and UXO. Inversions of field data over the Army's UXO Calibration Grid and Blind Test Grid at the Yuma Proving Ground (YPG), Arizona in 2006 produced polarizability moment values for many buried UXO items that were reasonable and generally repeatable for targets of the same type buried at different orientations and depths. In 2007 a test stand was constructed that allows for collection of data with varying spatial data density and accurate automated position control. The behavior of inverted ALLTEM test stand data as a function of spatial data density, sensor SNR, and position error has been investigated. The results indicate that the ALLTEM inversion algorithm is more tolerant of sensor noise and position error than has been reported for single-axis systems. A high confidence level in inversion-derived target parameters is required when a target is declared to be harmless scrap metal that may safely be left in the ground. Unless high confidence can be demonstrated, state regulators will likely require that targets be dug regardless of any "no-dig" classifications produced from inversions, in which case remediation costs would not be decreased.

Abundance and diversity of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)-metabolizing bacteria in UXO-contaminated marine sediments.

PubMed

Zhao, Jian-Shen; Manno, Dominic; Hawari, Jalal

2007-03-01

Octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) is a toxic explosive known to be resistant to biodegradation. In this study, we found that sediment collected from two unexploded ordnance (UXO) disposal sites (UXO-3, UXO-5) and one nearby reference site (midref) in Hawaii contained anaerobic bacteria capable of removing HMX. Two groups of HMX-removing bacteria were found in UXO-5: group I contained aerotolerant anaerobes and microaerophiles, and group II contained facultative anaerobes. In UXO-3 and midref sediments, HMX-metabolizing bacteria were strictly anaerobic (group III and group IV). Using 16S rRNA sequencing, group I was assigned to a novel phylogenetic cluster of Clostridiales, and groups II and III were related to Paenibacillus and Tepidibacter of Firmicutes, respectively. Group IV bacteria were identified as Desulfovibrio of Deltaproteobacteria. Using [UL-(14)C]-HMX, group IV isolates were found to mineralize HMX (26.8% in 308 d) as determined by liberated (14)CO(2), but negligible mineralization was observed in groups I-III. Resting cells of isolates metabolized HMX to N(2)O and HCHO via the intermediary formation of 1-nitroso-octahydro-3,5,7-trinitro-1,3,5,7-tetrazocine together with methylenedinitramine. These experimental findings suggest that HMX biotransformation occurred either via initial denitration followed by ring cleavage or via reduction of one or more of the N-NO(2) group(s) to the corresponding N-NO bond(s) prior to ring cleavage.

Trace Explosives Signatures from World War II Unexploded Undersea Ordnance

NASA Technical Reports Server (NTRS)

Darrach, M. R.; Chutjian, A.; Plett, G. A.

1998-01-01

Trace explosives signatures of TNT and DNT have been extracted from multiple sediment samples adjacent to unexploded undersea ordnance at Halifax Harbor, Canada. The ordnance was hurled into the harbor during a massive explosion some 50 years earlier, in 1945 after World War II had ended. Laboratory sediment extractions were made using the solid-phase microextraction (SPME) method in seawater and detection using the Reversal Electron Attachment Detection (READ) technique and, in the case of DNT, a commercial gas chromatograph/mass spectrometer (GC/MS). Results show that, after more than 50 years in the environment, ordnance that appeared to be physically intact gave good explosives signatures at the parts per billion level, whereas ordnance that had been cracked open during the explosion gave no signatures at the 10 parts per trillion sensitivity level. These measurements appear to provide the first reported data of explosives signatures from undersea unexploded ordnance.

Unexploded Ordnance Characterization And Detection in Muddy Estuarine Environments

NASA Astrophysics Data System (ADS)

Trembanis, A. C.; DuVal, C.

2017-12-01

There is recognized need for better quantitative understanding of the impact of coastal environments on UXO mobility, burial, and detection. Current efforts are underway to address aspects of UXO mobility and detection in sandy coastal areas. However, a significant data gap has been identified regarding UXO in shallow, muddy environments; 139 Formally Used Defense Sites (FUDS), in U.S. tidal waters alone, have been identified as containing muddy sediments. This study works to address this data gap. Using a shallow estuarine site in the Delaware Bay, this study 1) monitors the mobility and behavior of sensor-integrated surrogate munitions in muddy environments using a high-accuracy acoustic positioning system, 2) directly observes surrogate munition response to hydrodynamic forcing through instrumented bottom frame time-lapse hydrodynamic data and sonar imagery, and 3) monitors site changes through repetitive site surveying autonomous underwater vehicle (AUV) using both sonar and magnetometry. Surrogate UXO, modified with acoustic tracking devices and inertial motion units (IMU), are being deployed at a previously characterized muddy estuarine site. The surrogates are being monitored for changes in mobility and burial using the VEMCO positioning system, an off-the-shelf acoustic positioning system that is capable of tracking the position of multiple acoustic tags with accuracies down to 10 cm. Concurrently, time-series acoustic imagery and hydrodynamic sensors are being deployed to characterize UXO response to varied hydrodynamic conditions and compared to site-wide surrogate behavior. A series of repetitive surveys are being conducted using a magnetometer specifically designed for UXO detection on an autonomous underwater vehicle (AUV). Survey results will be compared to long-term acoustic positioning of the surrogate UXO to determine the effectiveness of the magnetometer for efficiently and effectively locating UXO in shallow, muddy environments. Additionally, this study will help inform parameters for UXO mobility and behavior in storms and muddy environments for integration into existing expert system models of UXO burial and mobility.

32 CFR 935.163 - Unexploded ordnance material.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Unexploded ordnance material. 935.163 Section 935.163 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND... immediately report its site to the Commander. ...

32 CFR 935.163 - Unexploded ordnance material.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Unexploded ordnance material. 935.163 Section 935.163 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND... immediately report its site to the Commander. ...

Evaluation of Statistical Methodologies Used in U. S. Army Ordnance and Explosive Work

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ostrouchov, G

2000-02-14

Oak Ridge National Laboratory was tasked by the U.S. Army Engineering and Support Center (Huntsville, AL) to evaluate the mathematical basis of existing software tools used to assist the Army with the characterization of sites potentially contaminated with unexploded ordnance (UXO). These software tools are collectively known as SiteStats/GridStats. The first purpose of the software is to guide sampling of underground anomalies to estimate a site's UXO density. The second purpose is to delineate areas of homogeneous UXO density that can be used in the formulation of response actions. It was found that SiteStats/GridStats does adequately guide the sampling somore » that the UXO density estimator for a sector is unbiased. However, the software's techniques for delineation of homogeneous areas perform less well than visual inspection, which is frequently used to override the software in the overall sectorization methodology. The main problems with the software lie in the criteria used to detect nonhomogeneity and those used to recommend the number of homogeneous subareas. SiteStats/GridStats is not a decision-making tool in the classical sense. Although it does provide information to decision makers, it does not require a decision based on that information. SiteStats/GridStats provides information that is supplemented by visual inspections, land-use plans, and risk estimates prior to making any decisions. Although the sector UXO density estimator is unbiased regardless of UXO density variation within a sector, its variability increases with increased sector density variation. For this reason, the current practice of visual inspection of individual sampled grid densities (as provided by Site-Stats/GridStats) is necessary to ensure approximate homogeneity, particularly at sites with medium to high UXO density. Together with Site-Stats/GridStats override capabilities, this provides a sufficient mechanism for homogeneous sectorization and thus yields representative UXO density estimates. Objections raised by various parties to the use of a numerical ''discriminator'' in SiteStats/GridStats were likely because of the fact that the concerned statistical technique is customarily applied for a different purpose and because of poor documentation. The ''discriminator'', in Site-Stats/GridStats is a ''tuning parameter'' for the sampling process, and it affects the precision of the grid density estimates through changes in required sample size. It is recommended that sector characterization in terms of a map showing contour lines of constant UXO density with an expressed uncertainty or confidence level is a better basis for remediation decisions than a sector UXO density point estimate. A number of spatial density estimation techniques could be adapted to the UXO density estimation problem.« less

Statistical Algorithms for Designing Geophysical Surveys to Detect UXO Target Areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Robert F.; Carlson, Deborah K.; Gilbert, Richard O.

2005-07-29

The U.S. Department of Defense is in the process of assessing and remediating closed, transferred, and transferring military training ranges across the United States. Many of these sites have areas that are known to contain unexploded ordnance (UXO). Other sites or portions of sites are not expected to contain UXO, but some verification of this expectation using geophysical surveys is needed. Many sites are so large that it is often impractical and/or cost prohibitive to perform surveys over 100% of the site. In that case, it is particularly important to be explicit about the performance required of the survey. Thismore » article presents the statistical algorithms developed to support the design of geophysical surveys along transects (swaths) to find target areas (TAs) of anomalous geophysical readings that may indicate the presence of UXO. The algorithms described here determine 1) the spacing between transects that should be used for the surveys to achieve a specified probability of traversing the TA, 2) the probability of both traversing and detecting a TA of anomalous geophysical readings when the spatial density of anomalies within the TA is either uniform (unchanging over space) or has a bivariate normal distribution, and 3) the probability that a TA exists when it was not found by surveying along transects. These algorithms have been implemented in the Visual Sample Plan (VSP) software to develop cost-effective transect survey designs that meet performance objectives.« less

Statistical Algorithms for Designing Geophysical Surveys to Detect UXO Target Areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Robert F.; Carlson, Deborah K.; Gilbert, Richard O.

2005-07-28

The U.S. Department of Defense is in the process of assessing and remediating closed, transferred, and transferring military training ranges across the United States. Many of these sites have areas that are known to contain unexploded ordnance (UXO). Other sites or portions of sites are not expected to contain UXO, but some verification of this expectation using geophysical surveys is needed. Many sites are so large that it is often impractical and/or cost prohibitive to perform surveys over 100% of the site. In such cases, it is particularly important to be explicit about the performance required of the surveys. Thismore » article presents the statistical algorithms developed to support the design of geophysical surveys along transects (swaths) to find target areas (TAs) of anomalous geophysical readings that may indicate the presence of UXO. The algorithms described here determine (1) the spacing between transects that should be used for the surveys to achieve a specified probability of traversing the TA, (2) the probability of both traversing and detecting a TA of anomalous geophysical readings when the spatial density of anomalies within the TA is either uniform (unchanging over space) or has a bivariate normal distribution, and (3) the probability that a TA exists when it was not found by surveying along transects. These algorithms have been implemented in the Visual Sample Plan (VSP) software to develop cost-effective transect survey designs that meet performance objectives.« less

Active tensor magnetic gradiometer system final report for Project MM–1514

USGS Publications Warehouse

Smith, David V.; Phillips, Jeffrey D.; Hutton, S. Raymond

2014-01-01

An interactive computer simulation program, based on physical models of system sensors, platform geometry, Earth environment, and spheroidal magnetically-permeable targets, was developed to generate synthetic magnetic field data from a conceptual tensor magnetic gradiometer system equipped with an active primary field generator. The system sensors emulate the prototype tensor magnetic gradiometer system (TMGS) developed under a separate contract for unexploded ordnance (UXO) detection and classification. Time-series data from different simulation scenarios were analyzed to recover physical dimensions of the target source. Helbig-Euler simulations were run with rectangular and rod-like source bodies to determine whether such a system could separate the induced component of the magnetization from the remanent component for each target. This report concludes with an engineering assessment of a practical system design.

Advanced Algorithms and High-Performance Testbed for Large-Scale Site Characterization and Subsurface Target Detecting Using Airborne Ground Penetrating SAR

NASA Technical Reports Server (NTRS)

Fijany, Amir; Collier, James B.; Citak, Ari

1997-01-01

A team of US Army Corps of Engineers, Omaha District and Engineering and Support Center, Huntsville, let Propulsion Laboratory (JPL), Stanford Research Institute (SRI), and Montgomery Watson is currently in the process of planning and conducting the largest ever survey at the Former Buckley Field (60,000 acres), in Colorado, by using SRI airborne, ground penetrating, Synthetic Aperture Radar (SAR). The purpose of this survey is the detection of surface and subsurface Unexploded Ordnance (UXO) and in a broader sense the site characterization for identification of contaminated as well as clear areas. In preparation for such a large-scale survey, JPL has been developing advanced algorithms and a high-performance restbed for processing of massive amount of expected SAR data from this site. Two key requirements of this project are the accuracy (in terms of UXO detection) and speed of SAR data processing. The first key feature of this testbed is a large degree of automation and a minimum degree of the need for human perception in the processing to achieve an acceptable processing rate of several hundred acres per day. For accurate UXO detection, novel algorithms have been developed and implemented. These algorithms analyze dual polarized (HH and VV) SAR data. They are based on the correlation of HH and VV SAR data and involve a rather large set of parameters for accurate detection of UXO. For each specific site, this set of parameters can be optimized by using ground truth data (i.e., known surface and subsurface UXOs). In this paper, we discuss these algorithms and their successful application for detection of surface and subsurface anti-tank mines by using a data set from Yuma proving Ground, A7, acquired by SRI SAR.

Focused feasibility study for surface soil at the main pits and pushout area, J-field toxic burning pits area, Aberdeen Proving Ground, Maryland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, T.; Benioff, P.; Biang, C.

1996-06-01

The Environmental Management Division of Aberdeen Proving Ground (APG), Maryland, is conducting a remedial investigation and feasibility study of the J-Field area at APG pursuant to the Comprehensive Environmental Response, Compensation, and Liability Act, as amended (CERCLA). J-Field is located within the Edgewood Area of APG in Harford County, Maryland. Since World War II, activities in the Edgewood Area have included the development, manufacture, testing, and destruction of chemical agents and munitions. These materials were destroyed at J-Field by open burning/open detonation. Portions of J-Field continue to be used for the detonation and disposal of unexploded ordnance (UXO) by openmore » burning/open detonation under authority of the Resource Conservation and Recovery Act.« less

Electromagnetic packable technology (EMPACT) for detection and characterization of ordnance in post-conflict areas

NASA Astrophysics Data System (ADS)

Schultz, Gregory; Miller, Jonathan; Keranen, Joe

2013-06-01

Land reclamation efforts in post-conflict regions are often hampered by the presence of Unexploded Ordnance (UXO) or other Explosive Remnants of War (ERW). Surface geophysical methods, such as Electromagnetic Induction (EMI) and magnetometry, are typically applied to screen rehabilitation areas for UXO prior to excavation; however, the prevalence of innocuous magnetic clutter related to indigenous scrap, fragmentation, or geology can severely impede the progress and efficiency of these remediation efforts. Additionally, the variability in surface conditions and local topography necessitates the development of sensor technologies that can be applied to a range of sites including those that prohibit the use of vehicle-mounted or large array systems. We present a man-portable EMI sensor known as the Electromagnetic Packable Technology (EMPACT) system that features a multi-axis sensor configuration in a compact form factor. The system is designed for operation in challenging site conditions and can be used in low ground-standoff modes to detect small and low-metal content objects. The EMPACT acquires high spatial density, multi-axis data that enable high resolution of small objects. This high density data can also be used to provide characterization of target physical features, such as size, material content, and shape. We summarize the development of this system for humanitarian demining operations and present results from preliminary system evaluations against a range of target types. Specifically, we assess the general detection capabilities of the EMPACT system and we evaluate the potential for target classification based on analysis of data and target model features.

Classification of MEC with the ALLTEM at Camp Stanley, Texas

USGS Publications Warehouse

Asch, T.; Moulton, C.; Smith, D.V.

2011-01-01

The ALLTEM is a multi-axis electromagnetic induction system designed for unexploded ordnance UXO applications. It uses a continuous triangle-wave excitation and provides good late-time signal-to-noise ratio SNR especially for ferrous targets. Multi-axis transmitter Tx and receiver Rx systems such as ALLTEM provide a richer data set from which to invert for the target parameters required to distinguish between clutter and UXO. Inversions of field data acquired between 2006 and 2010 over the Army's UXO Standardized Test sites at the Yuma Proving Ground YPG in Arizona and at the Aberdeen Proving Ground APG in Maryland have produced reasonable and generally repeatable results for many UXO items buried at different orientations and depths. In February-March 2011 ALLTEM data was acquired at two locations on the Camp Stanley Storage Activity CSSA just north of San Antonio, Texas. Camp Stanley is used to store munitions as well as test, fire, and overhaul munitions components. Site B-20 is an open burn/open detonation OBOD area and Site B-27 consists of narrow trenches blasted into limestone containing buried range and munitions debris and possibly MEC. The processing, analysis, and classification techniques developed at the controlled environments of YPG and APG have been applied to these two "live" sites at Camp Stanley. ALLTEM data analysis includes both classical numerical inversion of data from each anomaly and clustering of the raw data by means of a self-organizing map SOM via generalized neural network algorithms. Final classification consists of an integration of both the numerical and SOM results. ?? 2011 Society of Exploration Geophysicists.

Data collection and simulation of high range resolution laser radar for surface mine detection

NASA Astrophysics Data System (ADS)

Steinvall, Ove; Chevalier, Tomas; Larsson, Håkan

2006-05-01

Rapid and efficient detection of surface mines, IED's (Improvised Explosive Devices) and UXO (Unexploded Ordnance) is of high priority in military conflicts. High range resolution laser radars combined with passive hyper/multispectral sensors offer an interesting concept to help solving this problem. This paper reports on laser radar data collection of various surface mines in different types of terrain. In order to evaluate the capability of 3D imaging for detecting and classifying the objects of interest a scanning laser radar was used to scan mines and surrounding terrain with high angular and range resolution. These data were then fed into a laser radar model capable of generating range waveforms for a variety of system parameters and combinations of different targets and backgrounds. We can thus simulate a potential system by down sampling to relevant pixel sizes and laser/receiver characteristics. Data, simulations and examples will be presented.

Environmental Assessment: Base Realignment and Closure (BRAC) 2005 Mission Realignments to Vandenberg AFB

DTIC Science & Technology

2007-02-01

Utilities (3.11), and Health and Safety (3.12). The following areas of environmental consequences evaluated in the EA were determined to have the... Safety requires a walk- through survey prior to construction. Prior to the commencement of construction activities on the electrical substation site...an unexploded ordnance survey shall be conducted by 30th Space Wing Safety . Should any unexploded ordnances be identified as a result of the survey

Explosives detection in the marine environment using UUV-modified immunosensor

NASA Astrophysics Data System (ADS)

Charles, Paul T.; Adams, André A.; Deschamps, Jeffrey R.; Veitch, Scott P.; Hanson, Alfred; Kusterbeck, Anne W.

2011-05-01

Port and harbor security has rapidly become a point of interest and concern with the emergence of new improvised explosive devices (IEDs). The ability to provide physical surveillance and identification of IEDs and unexploded ordnances (UXO) at these entry points has led to an increased effort in the development of unmanned underwater vehicles (UUVs) equipped with sensing devices. Traditional sensors used to identify and locate potential threats are side scan sonar/acoustic methods and magnetometers. At the Naval Research Laboratory (NRL), we have developed an immunosensor capable of detecting trace levels of explosives that has been integrated into a REMUS payload for use in the marine environment. Laboratory tests using a modified PMMA microfluidic device with immobilized monoclonal antibodies specific for TNT and RDX have been conducted yielding detection levels in the low parts-per-billion (ppb) range. New designs and engineered improvements in microfluidic devices, fluorescence signal probes, and UUV internal fluidic and optical components have been investigated and integrated into the unmanned underwater prototype. Results from laboratory and recent field demonstrations using the prototype UUV immunosensor will be discussed. The immunosensor in combination with acoustic and other sensors could serve as a complementary characterization tool for the detection of IEDs, UXOs and other potential chemical or biological threats.

Yuma proving grounds automatic UXO detection using biomorphic robots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tilden, M.W.

1996-07-01

The current variety and dispersion of Unexploded Ordnance (UXO) is a daunting technological problem for current sensory and extraction techniques. The bottom line is that the only way to insure a live UXO has been found and removed is to step on it. As this is an upsetting proposition for biological organisms like animals, farmers, or Yuma field personnel, this paper details a non-biological approach to developing inexpensive, automatic machines that will find, tag, and may eventually remove UXO from a variety of terrains by several proposed methods. The Yuma proving grounds (Arizona) has been pelted with bombs, mines, missiles,more » and shells since the 1940s. The idea of automatic machines that can clean up after such testing is an old one but as yet unrealized because of the daunting cost, power and complexity requirements of capable robot mechanisms. A researcher at Los Alamos National Laboratory has invented and developed a new variety of living robots that are solar powered, legged, autonomous, adaptive to massive damage, and very inexpensive. This technology, called Nervous Networks (Nv), allows for the creation of capable walking mechanisms (known as Biomorphic robots, or Biomechs for short) that rather than work from task principles use instead a survival-based design philosophy. This allows Nv based machines to continue doing work even after multiple limbs and sensors have been removed or damaged, and to dynamically negotiate complex terrains as an emergent property of their operation (fighting to proceed, as it were). They are not programmed, and indeed, the twelve transistor Nv controller keeps their electronic cost well below that of most pocket radios. It is suspected that advanced forms of these machines in huge numbers may be an interesting, capable solution to the problem of general and specific UXO identification, tagging, and removal.« less

A cross-sectional community study of post-traumatic stress disorder and social support in Lao People's Democratic Republic

PubMed Central

Southivong, Bouavanh; Nakahara, Shinji; Southivong, Chanhpheng

2013-01-01

Abstract Objective To estimate post-traumatic stress disorder (PTSD) symptoms in those injured and not injured by landmines or unexploded ordnance (UXO) in rural Lao People's Democratic Republic and to determine whether the perception of social support was associated with PTSD symptom severity. Methods A community survey was conducted among 190 people injured by landmines or UXO and 380 age-, sex- and neighbourhood-matched non-injured individuals in the Sepone district of Savannakhet Province, the part of the Lao People's Democratic Republic most heavily bombed during the Viet Nam War. Using the Harvard Trauma Questionnaire and the Medical Outcomes Study Social Support Survey, trained health-care workers conducted face-to-face interviews to assess PTSD symptoms and level of perceived social support. Multiple linear regression was performed to explore the association between social support and other factors and PTSD. Findings The prevalence of PTSD was higher among the injured (10%) than among the non-injured (4%), but the level of perceived social support was not significantly different between the two groups. A higher level of perceived social support was associated with milder symptoms of PTSD. Women, older people and those with a formal education were more often and more severely affected by PTSD. Conclusion The perception of strong social support might help to alleviate the symptoms of PTSD among people injured by landmines or UXO in rural parts of the Lao People's Democratic Republic. Psychosocial interventions should be incorporated in assistance for the injured because they have more severe and longer-lasting symptoms of PTSD than the non-injured. PMID:24115800

The effect of explosive remnants of war on global public health: a systematic mixed-studies review using narrative synthesis.

PubMed

Frost, Alexandra; Boyle, Peter; Autier, Philippe; King, Colin; Zwijnenburg, Wim; Hewitson, David; Sullivan, Richard

2017-06-01

Explosive remnants of war (ERW)-landmines, unexploded ordnance (UXO), and abandoned explosive ordnance (AXO)-have been recognised as a threat to health since the 1990s. We aimed to study the effect of ERW on global public health. In this systematic mixed-studies review, we searched the Web of Science, Scopus, PubMed, and ProQuest databases, and hand searched relevant websites, for articles published between Jan 1, 1990, and Aug 31, 2015. We used keywords and Medical Subject Headings related to ERW, landmines, UXO, and AXO to locate original peer-reviewed quantitative, qualitative, or mixed-methods studies in English of the direct physical or psychological effects of ERW on direct victims of the explosive device or reverberating social and economic effects on direct victims and indirect victims (their families and the wider at-risk community). We excluded studies if more than 20% of participants were military, if they were of deminers, if they were from high-income countries, or if they were of chemical weapons. We identified no peer-reviewed studies of AXO effects, so we extended the search to include grey literature. We critically appraised study quality using a mixed methods appraisal tool. We used a narrative synthesis approach to categorise and synthesise the literature. We extracted quantitative data and calculated means and percentages. The initial search identified 10 226 studies, leaving 8378 (82%) after removal of duplicates, of which we reviewed 54 (26 [48%] were quantitative descriptive studies, 20 [37%] were quantitative non-randomised studies, four [7%] were mixed-methods studies, and four [7%] were grey literature). The direct psychological effects of landmines or UXO appear high. We identified comorbidity of anxiety and depression in landmine or UXO victims in four studies, more women presented with post-traumatic stress disorder than did men in two studies, and landmine or UXO victims reported a greater prevalence of post-traumatic stress disorder, anxiety, or depression than did control groups in two studies. Overall injury and mortality rates caused by landmines or UXO decreased over time across five studies and increased in one. More men were injured or killed by landmines or UXO than were women (0-30·6% of women), the mean ages of casualties ranged from 18·5 years to 38·1 years, and victims were likely to be doing an activity of economic necessity at the time of injury. The proportion of casualties of landmines or UXO younger than 18 years ranged from 22% to 55% across twelve studies. Landmine or UXO victims who had one or more limbs amputated ranged from 19·5% to 82·6%. Landmines and UXO had a negative effect on internally displaced populations and returning refugees, physical security, economic productivity, child health and educational attainment, food security, and agriculture in studies from seven countries. We could not establish the proportion of casualties caused by AXO from unplanned explosions at munitions sites, although the grey literature suggests that AXO is a substantial problem. Individually, these landmine and UXO results are not new and substantiate findings from existing research. Taken together, however, these findings provide a picture of the effect of landmines and UXO that stretches far beyond injury and mortality prevalence, making landmine and UXO clearance a more favourable option for funders. AXO effects are understudied and warrant further research. King's College London. Copyright © 2017 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license. Published by Elsevier Ltd.. All rights reserved.

EMPACT 3D: an advanced EMI discrimination sensor for CONUS and OCONUS applications

NASA Astrophysics Data System (ADS)

Keranen, Joe; Miller, Jonathan S.; Schultz, Gregory; Sander-Olhoeft, Morgan; Laudato, Stephen

2018-04-01

We recently developed a new, man-portable, electromagnetic induction (EMI) sensor designed to detect and classify small, unexploded sub-munitions and discriminate them from non-hazardous debris. The ability to distinguish innocuous metal clutter from potentially hazardous unexploded ordnance (UXO) and other explosive remnants of war (ERW) before excavation can significantly accelerate land reclamation efforts by eliminating time spent removing harmless scrap metal. The EMI sensor employs a multi-axis transmitter and receiver configuration to produce data sufficient for anomaly discrimination. A real-time data inversion routine produces intrinsic and extrinsic anomaly features describing the polarizability, location, and orientation of the anomaly under test. We discuss data acquisition and post-processing software development, and results from laboratory and field tests demonstrating the discrimination capability of the system. Data acquisition and real-time processing emphasize ease-of-use, quality control (QC), and display of discrimination results. Integration of the QC and discrimination methods into the data acquisition software reduces the time required between sensor data collection and the final anomaly discrimination result. The system supports multiple concepts of operations (CONOPs) including: 1) a non-GPS cued configuration in which detected anomalies are discriminated and excavated immediately following the anomaly survey; 2) GPS integration to survey multiple anomalies to produce a prioritized dig list with global anomaly locations; and 3) a dynamic mapping configuration supporting detection followed by discrimination and excavation of targets of interest.

Investigation of a new passive sampler for the detection of munitions compounds in marine and freshwater systems.

PubMed

Warren, Joseph K; Vlahos, Penny; Smith, Richard; Tobias, Craig

2018-07-01

Over the last century, unexploded ordnances have been disposed of in marine shelf systems because of a lack of cost-effective alternatives. Underwater unexploded ordnances have the potential to leak 2,4,6-trinitrotoluene (TNT) and 1,3,5-trinitro-1,3,5-triazine (RDX), commonly used chemical munitions, and contaminate local waters, biota, and sediments. The rate at which this contamination occurs in the environment is relatively unknown, and the cost- and time-prohibitive nature of sampling across sites makes mapping difficult. In the present study we assessed the efficacy of ethylene-vinyl acetate (EVA) for sampling relatively soluble munitions compounds over a range of environmental conditions (i.e., changes in temperature and salinity) and optimized the composition of the passive sampling polymer. The EVA sampler was able to successfully detect ambient concentrations of lingering munitions compounds from field sites containing unexploded ordnances. The sampler affinity for the munitions in terms of an EVA-water partition coefficient was greater than the standard octanol water values for each target compound. Partitioning of compounds onto EVA over the natural ranges of salinity did not change significantly, although uptake varied consistently and predictably with temperature. Increasing the vinyl acetate to ethylene ratio of the polymer corresponded to an increase in uptake capacity, consistent with enhanced dipole-dipole interactions between the munitions and the polymer. This sampler provides a cost-effective means to map and track leakage of unexploded ordnances both spatially and temporally. Environ Toxicol Chem 2018;37:1990-1997. © 2018 SETAC. © 2018 SETAC.

Chemical sensing system for classification of minelike objects by explosives detection

NASA Astrophysics Data System (ADS)

Chambers, William B.; Rodacy, Philip J.; Jones, Edwin E.; Gomez, Bernard J.; Woodfin, Ronald L.

1998-09-01

Sandia National Laboratories has conducted research in chemical sensing and analysis of explosives for many years. Recently, that experience has been directed towards detecting mines and unexploded ordnance (UXO) by sensing the low-level explosive signatures associated with these objects. Our focus has been on the classification of UXO in shallow water and anti-personnel/anti tank mines on land. The objective of this work is to develop a field portable chemical sensing system which can be used to examine mine-like objects (MLO) to determine whether there are explosive molecules associated with the MLO. Two sampling subsystems have been designed, one for water collection and one for soil/vapor sampling. The water sampler utilizes a flow-through chemical adsorbent canister to extract and concentrate the explosive molecules. Explosive molecules are thermally desorbed from the concentrator and trapped in a focusing stage for rapid desorption into an ion-mobility spectrometer (IMS). We will describe a prototype system which consists of a sampler, concentrator-focuser, and detector. The soil sampler employs a light-weight probe for extracting and concentrating explosive vapor from the soil in the vicinity of an MLO. The chemical sensing system is capable of sub-part-per-billion detection of TNT and related explosive munition compounds. We will present the results of field and laboratory tests on buried landmines, which demonstrate our ability to detect the explosive signatures associated with these objects.

Discrimination between landmine and mine-like targets using wavelets and spectral analysis

NASA Astrophysics Data System (ADS)

Mohana, Mahmoud A.; Abbas, Abbas M.; Gomaa, Mohamed L.; Ebrahim, Shereen M.

2013-06-01

Landmine is an explosive apparatus hidden in or on the ground, which blows up when a person or vehicle passes over it. Egypt is one of the countries suffering due to the unexploded ordnance (UXO). Around 2 million UXO are present in the Egyptian soil especially at Al-Alameen province, north of the western desert. Detection of buried landmines is a problem of military and humanitarian importance. Ground penetrating radar (GPR) is a powerful and non-destructive geophysical approach with a wide range of advantages in the field of landmine inspection. In the present paper, we apply different simulation models with Vivaldi antenna and mine-like targets by using the CST Microwave studio program. The field work is carried out by using a GPR device of model SIR 2000 from GSSI (Geophysical Survey Systems Incorporation) connected to 900 MHz antenna where the targets were buried in sand soil. Depending on the fact that the receiving powers (reflected, refracted and scattered) from the different materials are different, we study the spectral power densities for the received power from the different targets. The techniques used in this study are: direct fast Fourier transform, short time Fourier transform (spectrogram), wavelets transform and denoising techniques. Our results ought to be considered as finger prints for different scanned targets during this work. So we can discriminate between landmines and mine-like targets.

Detection and Classification of UXO Using Unmanned Undersea Electromagnetic Sensing Platforms

NASA Astrophysics Data System (ADS)

Schultz, G.; Keranen, J.; McNinch, J.; Miller, J.

2017-12-01

Important seafloor applications, including mine countermeasures, unexploded ordnance (UXO) surveys, salvage, and underwater hazards, require the detection, geo-registration, and characterization of man-made targets on, or below, the seafloor. Investigations in littoral environments can be time-consuming and expensive due to the challenges of accurately tracking underwater assets, the difficulty of quick or effective site reconnaissance activities, high levels of clutter in nearshore areas, and lack of situational awareness and real-time feedback to operators. Consequently, a high payoff exists for effective methods using sensor and data fusion, feature extraction, and effective payload integration and deployment for improved assessments of littoral infrastructure. We present technology development and demonstration results from multiple technology research, development, and demonstration projects over the last 3 years that have been focused on advancing seafloor target detection, tracking, and classification for specific environmental and defense missions. We focus on challenges overcome in integrating and testing new miniaturized passive magnetic and controlled-source electromagnetic sensors on a variety of remotely and autonomously operated sensing platforms (ROVs, AUVs and bottom crawling systems). In particular, we present aspects of the design, development, and testing of array configurations of miniaturized atomic magnetometers/gradiometers and multi-dimensional electromagnetic (EM) sensor arrays. Results from nearshore (surf zone and marsh in North Carolina) and littoral experiments (bays and reef areas of Florida Gulf and Florida Keys) are presented.

Development of Autonomous Magnetometer Rotorcraft For Wide Area Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark D. McKay; Matthew O. Anderson

2011-08-01

Large areas across the United States and internationally are potentially contaminated with unexploded ordinance (UXO), with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with (1) near 100% coverage and (2) near 100% detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area assessment is a multi-level one, in which medium - altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry. Subsequent to this wide areamore » assessment targeted surface investigations are performed using either towed geophysical sensor arrays or man portable sensors. In order to be an effective tool for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 to 3 meters. These altitude requirements mean that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys, resulting in costs of approximately $100-$150/acre. In addition, due to the low altitude there are substantial risks to pilots and equipment. Surface towed arrays provide highresolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. Thus there is a need for other systems, which can be used for effective data collection. An Unmanned Aerial Vehicle (UAV) magnetometer platform is an obvious alternative. The motivation behind such a system is that it reduces risk to operators, is lower in initial and Operational and Maintenance (O&M) costs (and can thus potentially be applied to smaller sites) and has the potential of being more effective in terms of detection and possibly characterization (through the use of dynamic acquisition, i.e. survey mission in-flight reprioritization).« less

Joint Ordnance Test Procedure (JOTP)-001 Allied Ammunition Safety and Suitability for Service Assessment Testing Publication - Guidance

DTIC Science & Technology

2013-01-08

hazard due to enemy attack or accident (e.g. Insensitive Munitions (IM) and Electromagnetic Environmental Effects (E3)) and the explosive materials...of mitigating potential explosive remnants of war hazards , particularly from unexploded ordnance , should be conducted. 6.5 Munition Software System...TYPE Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Joint Ordnance Test Procedure (JOTP)-001 Allied Ammunition Safety and

Remote sensing using airships

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavan, C.K. Jr.

1996-10-01

Loral Defense Systems-Akron (LDSA) has developed a laser-based mine detection system in response to the US Navy`s requirements for detecting, localizing and classifying mines in deep water shipping channels. This sensor system was tested recently at the Navy`s David Taylor Research Center (DTRC) at Bethesda, MD and at the US Army`s Camp Perry near Lake Erie. The testing at Camp Perry involved installation of the sensor system on the Goodyear Tim & Rubber Company`s airship {open_quotes}Spirit of Akron{close_quotes} and the conduct of control flight test experiments over Lake Erie. Resultant imagery has been analyzed in terms of water optical properties.more » Further tests are planned in a multispectral mode incorporating both active illumination and passive detection. The system can be extended to the detection of Unexploded Ordnance (UXO) in government test ranges and to detection of other devices both buried and at the surface. The utility of the airship (blimp) makes the approach practical due to long endurance, wide speed range and platform flexibility. 14 figs.« less

The Tragic Bazooka Accident at Los Alamos on July 14, 1962

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skidmore, Cary Bradford

In recent years the Laboratory has made information (documents, photographs, and perspectives) regarding the occupational explosives accidents that killed seven men in the late 1950s more accessible to the public. While pursuing this effort, we were reminded of similar tragedies that occurred to children of the community. The purpose of this paper is to make information that has come into our hands more available to the public regarding these accidents. Following this introduction, a brief synopsis is provided for each accident. The appendices contain source documents for the 1962 accident that are not generally available. The community of Los Alamos,more » New Mexico was born out of a military post created to support the secret Manhattan Project during World War II. Security was provided by military police and some training exercises were conducted using live ordnance. In two instances unexploded ordnance (UXO) from this era was found “in the field” by residents hiking in the local area and brought into town. Tragically, handling these “bazooka” rounds as “dud” munitions resulted in death for one child and injury to several others. The first accident occurred on Saturday, September 6, 1947, which resulted in injuries to two boys, ages 5 and 12. The second accident occurred on Saturday, July 14, 1962 and resulted in the death of one five-year-old boy, and injuries to four other children, ages 6 to 10 years-old. The latter accident is the primary focus of the paper.« less

Explosives Dissolved from Unexploded Ordnance

DTIC Science & Technology

2011-10-01

octahydro-1,3,5,7-tetranitrotetrazocine (often a bi- product of RDX production) HPLC High performance Liquid Chromatography IC Ion conductivity MMR...orange. Conductivity sensor 60-mm ordnance Nalgene bottle Water sample access 29 The water samples were analyzed with an ion chromatography ...Figure 41. Relationship between the ion conductivity measurements made on water samples and electrical conductivity measurements for one of

Overview of the laser activities at Rheinmetall Waffe Munition

NASA Astrophysics Data System (ADS)

Ludewigt, Klaus; Riesbeck, Thomas; Schünemann, B.; Graf, A.; Jung, Markus; Schreiber, Th.; Eberhardt, Ramona; Tünnermann, A.

2012-11-01

The paper will give an overview over the laser weapon activities at RWM (Rheinmetall Waffe Munition) over the last years. Starting from the actual scenarios for laser weapon applications as: CRAM (Counter Rocket Artillery Mortar), Air Defence and UXO (unexploded ordnance) clearing. The basic requirements of a future laser weapon as beam diameter, beam quality, tracking capability, adaptive optics were deduced. For the UXO scenario a mobile directed energy laser demonstrator for humanitarian mine and UXO clearing based on fiber lasers is presented. Based on the parameters the system concept including the cooling system, power supply and the integration into the armoured vehicle TM 170 are explained. The contribution show first experiments of UXO and IED clearing. Different technical approaches to achieve laser power in the 100 kW regime combined with very good beam quality are discussed to fulfil the requirements of the CRAM and Air Defence scenario. Spectral coupling and the beam superimposing both are performed by Rheinmetall Waffe Munition. At the spectral coupling the basic technology parameters for the fiber laser and the dielectric grating as the latest results were put into context with the power levels reached at other groups. For the beam super imposing technology the basic experiments regarding the tracking capability and compensation of the atmosphere on the test range at Unterlüß will be explained. A generic 10 kW Laser Weapon Demonstrator based on 2 Laser Weapon Modules (LWM) from RWM each 5 kW fiber Laser with beam forming and tracking integrate by the team of RWM and RAD (Rheinmetall Air Defense) into a Ground based Air Defend system consisting of Skyguard and Millenium turret are presented. The flight path of the UAV within the valley of the life firing range at Ochsenboden Switzerland is shown. Selected results of the successful tests against UAV's are presented. It shows the capability of the generic 10 kW Laser Weapon Demonstrator to track and to destroy the target. From these results the next steps of Rheinmetall Waffe Munition for a 100 kW class laser weapon are explained.

Remedial Design/Remedial Action Work Plan for Operable Units 6-05 and 10-04, Phase IV

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. P. Wells

2006-11-14

This Phase IV Remedial Design/Remedial Action Work Plan addresses the remediation of areas with the potential for UXO at the Idaho National Laboratory. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. Five areas within the Naval Proving Ground that are known to contain UXO include the Naval Ordnance Disposal Area, the Mass Detonation Area, the Experimental Field Station, The Rail Car Explosion Area, and the Land Mine Fuze Burn Area. The Phase IV remedial action will be concentrated in these five areas. For other areas, such as themore » Arco High-Altitude Bombing Range and the Twin Buttes Bombing Range, ordnance has largely consisted of sand-filled practice bombs that do not pose an explosion risk. Ordnance encountered in these areas will be addressed under the Phase I Operations and Maintenance Plan that allows for the recovery and disposal of ordnance that poses an imminent risk to human health or the environment.« less

A High-Performance Portable Transient Electro-Magnetic Sensor for Unexploded Ordnance Detection.

PubMed

Wang, Haofeng; Chen, Shudong; Zhang, Shuang; Yuan, Zhiwen; Zhang, Haiyang; Fang, Dong; Zhu, Jun

2017-11-17

Portable transient electromagnetic (TEM) systems can be well adapted to various terrains, including mountainous, woodland, and other complex terrains. They are widely used for the detection of unexploded ordnance (UXO). As the core component of the portable TEM system, the sensor is constructed with a transmitting coil and a receiving coil. Based on the primary field of the transmitting coil and internal noise of the receiving coil, the design and testing of such a sensor is described in detail. Results indicate that the primary field of the transmitting coil depends on the diameter, mass, and power of the coil. A higher mass-power product and a larger diameter causes a stronger primary field. Reducing the number of turns and increasing the clamp voltage reduces the switch-off time of the transmitting current effectively. Increasing the cross-section of the wire reduces the power consumption, but greatly increases the coil's weight. The study of the receiving coil shows that the internal noise of the sensor is dominated by the thermal noise of the damping resistor. Reducing the bandwidth of the system and increasing the size of the coil reduces the internal noise effectively. The cross-sectional area and the distance between the sections of the coil have little effect on the internal noise. A less damped state can effectively reduce signal distortion. Finally, a portable TEM sensor with both a transmitting coil (constructed with a diameter, number of turns, and transmitting current of 0.5 m, 30, and 5 A, respectively) and a receiving coil (constructed with a length and resonant frequency of 5.6 cm and 50 kHz, respectively) was built. The agreement between experimental and calculated results confirms the theory used in the sensor design. The responses of an 82 mm mortar shell at different distances were measured and inverted by the differential evolution (DE) algorithm to verify system performance. Results show that the sensor designed in this study can not only detect the 82 mm mortar shell within 1.2 m effectively but also locate the target precisely.

A Research and Development Strategy for Unexploded Ordnance Sensing

DTIC Science & Technology

1996-04-01

Each lane was carefully traversed with the MK-26 Ordnance Detector (dual fluxgate magnetometer hand-held unit) and the operator hand-excavated any...proton-precessing magnetometers , optically pumped magnetometers , fluxgates magnetometers , and magnetometers based on superconducting quantum...sensitivity better than 0.05 nT, and the optically-pumped magnetometers have sensitivity better than 0.005 nT. Fluxgate magnetometers are based on solid

Autonomous mine detection system (AMDS) neutralization payload module

NASA Astrophysics Data System (ADS)

Majerus, M.; Vanaman, R.; Wright, N.

2010-04-01

The Autonomous Mine Detection System (AMDS) program is developing a landmine and explosive hazards standoff detection, marking, and neutralization system for dismounted soldiers. The AMDS Capabilities Development Document (CDD) has identified the requirement to deploy three payload modules for small robotic platforms: mine detection and marking, explosives detection and marking, and neutralization. This paper addresses the neutralization payload module. There are a number of challenges that must be overcome for the neutralization payload module to be successfully integrated into AMDS. The neutralizer must meet stringent size, weight, and power (SWaP) requirements to be compatible with a small robot. The neutralizer must be effective against a broad threat, to include metal and plastic-cased Anti-Personnel (AP) and Anti-Tank (AT) landmines, explosive devices, and Unexploded Explosive Ordnance (UXO.) It must adapt to a variety of threat concealments, overburdens, and emplacement methods, to include soil, gravel, asphalt, and concrete. A unique neutralization technology is being investigated for adaptation to the AMDS Neutralization Module. This paper will describe review this technology and how the other two payload modules influence its design for minimizing SWaP. Recent modeling and experimental efforts will be included.

Pedemis: a portable electromagnetic induction sensor with integrated positioning

NASA Astrophysics Data System (ADS)

Barrowes, Benjamin E.; Shubitidze, Fridon; Grzegorczyk, Tomasz M.; Fernández, Pablo; O'Neill, Kevin

2012-06-01

Pedemis (PortablE Decoupled Electromagnetic Induction Sensor) is a time-domain handheld electromagnetic induction (EMI) instrument with the intended purpose of improving the detection and classification of UneXploded Ordnance (UXO). Pedemis sports nine coplanar transmitters (the Tx assembly) and nine triaxial receivers held in a fixed geometry with respect to each other (the Rx assembly) but with that Rx assembly physically decoupled from the Tx assembly allowing flexible data acquisition modes and deployment options. The data acquisition (DAQ) electronics consists of the National Instruments (NI) cRIO platform which is much lighter and more energy efficient that prior DAQ platforms. Pedemis has successfully acquired initial data, and inversion of the data acquired during these initial tests has yielded satisfactory polarizabilities of a spherical target. In addition, precise positioning of the Rx assembly has been achieved via position inversion algorithms based solely on the data acquired from the receivers during the "on-time" of the primary field. Pedemis has been designed to be a flexible yet user friendly EMI instrument that can survey, detect and classify targets in a one pass solution. In this paper, the Pedemis instrument is introduced along with its operation protocols, initial data results, and current status.

Biosensor UUV payload for underwater detection

NASA Astrophysics Data System (ADS)

Kusterbeck, Anne W.; Charles, Paul T.; Melde, Brian J.; Trammell, Scott A.; Adams, André A.; Deschamps, Jeffrey R.

2010-04-01

Increased emphasis on maritime domain awareness and port security has led to the development of unmanned underwater vehicles (UUVs) capable of extended missions. These systems rely most frequently on well-developed side scan sonar and acoustic methods to locate potential targets. The Naval Research Laboratory (NRL) is developing biosensors for underwater explosives detection that complement acoustic sensors and can be used as UUV payloads to monitor areas for port and harbor security or in detection of underwater unexploded ordnance (UXO) and biochemical threats. The prototype sensor has recently been demonstrated to detect explosives in seawater at trace levels when run in a continuous sampling mode. To overcome ongoing issues with sample preparation and facilitate rapid detection at trace levels in a marine environment, we have been developing new mesoporous materials for in-line preconcentration of explosives and other small molecules, engineering microfluidic components to improve the signal, and testing alternative signal transduction methods. Additional work is being done to optimize the optical components and sensor response time. Highlights of these current studies and our ongoing efforts to integrate the biosensor with existing detection technologies to reduce false positives are described. In addition, we present the results of field tests that demonstrate the prototype biosensor performance as a UUV payload.

PELAN applications and recent field tests

NASA Astrophysics Data System (ADS)

Martinez, Juan J.; Holslin, Daniel T.

2004-10-01

When neutrons interact with particular nuclei, the resulting energy of the interaction can be released in the form of gamma rays, which are characteristic of the nucleus involved in the reaction. The PELAN (Pulsed Elemental Analysis with Neutrons) system uses a pulsed neutron generator and an integral thermalizing shield that induce reactions that cover most of the entire gamma ray energy spectra1. The neutron generator uses a D-T reaction, which releases fast 14MeV neutrons responsible for providing information on those nuclei that mostly respond to inelastic scattering. During the time period between pulses, the fast neutrons undergo multiple inelastic interactions that lower their energy making them easier to be captured by certain nuclei; this energy spectrum of gamma rays induced by these interactions are designated as the gamma ray thermal spectra. The PELAN system has been used for a number of applications where non-intrusive, non-destructive interrogation is needed. Although Pulsed Fast Thermal Neutron Analysis (PFTNA) has been around for approximately 30 years, the technology has never been successfully commercialized for practical applications. The following report illustrates examples of the performance of on a number of applications of interrogation of Unexploded Ordnance (UXO), mine confirmation, large vehicle bombs inspection and illicit drug smuggling detection.

Detecting submerged features in water: modeling, sensors, and measurements

NASA Astrophysics Data System (ADS)

Bostater, Charles R., Jr.; Bassetti, Luce

2004-11-01

It is becoming more important to understand the remote sensing systems and associated autonomous or semi-autonomous methodologies (robotic & mechatronics) that may be utilized in freshwater and marine aquatic environments. This need comes from several issues related not only to advances in our scientific understanding and technological capabilities, but also from the desire to insure that the risk associated with UXO (unexploded ordnance), related submerged mines, as well as submerged targets (such as submerged aquatic vegetation) and debris left from previous human activities are remotely sensed and identified followed by reduced risks through detection and removal. This paper will describe (a) remote sensing systems, (b) platforms (fixed and mobile, as well as to demonstrate (c) the value of thinking in terms of scalability as well as modularity in the design and application of new systems now being constructed within our laboratory and other laboratories, as well as future systems. New remote sensing systems - moving or fixed sensing systems, as well as autonomous or semi-autonomous robotic and mechatronic systems will be essential to secure domestic preparedness for humanitarian reasons. These remote sensing systems hold tremendous value, if thoughtfully designed for other applications which include environmental monitoring in ambient environments.

Munitions related feature extraction from LIDAR data.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, Barry L.

2010-06-01

The characterization of former military munitions ranges is critical in the identification of areas likely to contain residual unexploded ordnance (UXO). Although these ranges are large, often covering tens-of-thousands of acres, the actual target areas represent only a small fraction of the sites. The challenge is that many of these sites do not have records indicating locations of former target areas. The identification of target areas is critical in the characterization and remediation of these sites. The Strategic Environmental Research and Development Program (SERDP) and Environmental Security Technology Certification Program (ESTCP) of the DoD have been developing and implementing techniquesmore » for the efficient characterization of large munitions ranges. As part of this process, high-resolution LIDAR terrain data sets have been collected over several former ranges. These data sets have been shown to contain information relating to former munitions usage at these ranges, specifically terrain cratering due to high-explosives detonations. The location and relative intensity of crater features can provide information critical in reconstructing the usage history of a range, and indicate areas most likely to contain UXO. We have developed an automated procedure using an adaptation of the Circular Hough Transform for the identification of crater features in LIDAR terrain data. The Circular Hough Transform is highly adept at finding circular features (craters) in noisy terrain data sets. This technique has the ability to find features of a specific radius providing a means of filtering features based on expected scale and providing additional spatial characterization of the identified feature. This method of automated crater identification has been applied to several former munitions ranges with positive results.« less

Contribution of hydrolysis in the abiotic attenuation of RDX and HMX in coastal waters.

PubMed

Monteil-Rivera, Fanny; Paquet, Louise; Giroux, Romain; Hawari, Jalal

2008-01-01

Sinking of military ships, dumping of munitions during the two World Wars, and military training have resulted in the undersea deposition of numerous unexploded ordnances (UXOs). Leaching of energetic compounds such as hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) from these UXOs may cause adverse ecological effects so that the long-term fate of these chemicals in the sea should be known. The present study assesses the contribution of alkaline hydrolysis into the natural attenuation of RDX and HMX in coastal waters. Alkaline hydrolysis rates were shown to be unaffected by the presence of sodium chloride, the most common component in marine waters. Kinetic parameters (E(a), ln A, k(2)) quantified for the alkaline hydrolysis of RDX and HMX in deionized water (30-50 degrees C, pH 10-12) agreed relatively well with abiotic degradation rates determined in sterilized natural coastal waters (50 and 60 degrees C, variable salinity) even if the latter were generally slightly faster than the former. Furthermore, similar products (HCHO, NO(2)(-), O(2)NNHCH(2)NHCHO) were obtained on alkaline hydrolysis in deionized water and abiotic degradation in coastal waters. These two findings suggested that degradation of nitramines in sterilized natural coastal waters, away from light, was mainly governed by alkaline hydrolysis. Kinetic calculations using the present parameters showed that alkaline hydrolysis of RDX and HMX in marine waters at 10 degrees C would respectively take 112 +/- 10 and 2408 +/- 217 yr to be completed (99.0%). We concluded that under natural conditions hydrolysis should not contribute significantly to the natural attenuation of HMX in coastal waters whereas it could play an active role in the natural attenuation of RDX.

The DTIC Review. Volume 2, Number 1: Land Mine Warfare: Detection and Clearance

DTIC Science & Technology

1996-03-01

almost all explosives, of some nitrate form, can be used as a key to determine ordnance presence. Assuming the presence of explosive contamination on the...heat the nitrate compounds found therein in the presence of a catalyst to produce nitrous oxide. This gas can then be measured and a direct... economical means of characterizing and remediating sites contaminated with UXO. This program extends from UXO detection systems, through artificial

Hybrid analysis of multiaxis electromagnetic data for discrimination of munitions and explosives of concern

USGS Publications Warehouse

Friedel, M.J.; Asch, T.H.; Oden, C.

2012-01-01

The remediation of land containing munitions and explosives of concern, otherwise known as unexploded ordnance, is an ongoing problem facing the U.S. Department of Defense and similar agencies worldwide that have used or are transferring training ranges or munitions disposal areas to civilian control. The expense associated with cleanup of land previously used for military training and war provides impetus for research towards enhanced discrimination of buried unexploded ordnance. Towards reducing that expense, a multiaxis electromagnetic induction data collection and software system, called ALLTEM, was designed and tested with support from the U.S. Department of Defense Environmental Security Technology Certification Program. ALLTEM is an on-time time-domain system that uses a continuous triangle-wave excitation to measure the target-step response rather than traditional impulse response. The system cycles through three orthogonal transmitting loops and records a total of 19 different transmitting and receiving loop combinations with a nominal spatial data sampling interval of 20 cm. Recorded data are pre-processed and then used in a hybrid discrimination scheme involving both data-driven and numerical classification techniques. The data-driven classification scheme is accomplished in three steps. First, field observations are used to train a type of unsupervised artificial neural network, a self-organizing map (SOM). Second, the SOM is used to simultaneously estimate target parameters (depth, azimuth, inclination, item type and weight) by iterative minimization of the topographic error vectors. Third, the target classification is accomplished by evaluating histograms of the estimated parameters. The numerical classification scheme is also accomplished in three steps. First, the Biot–Savart law is used to model the primary magnetic fields from the transmitter coils and the secondary magnetic fields generated by currents induced in the target materials in the ground. Second, the target response is modelled by three orthogonal dipoles from prolate, oblate and triaxial ellipsoids with one long axis and two shorter axes. Each target consists of all three dipoles. Third, unknown target parameters are determined by comparing modelled to measured target responses. By comparing the rms error among the self-organizing map and numerical classification results, we achieved greater than 95 per cent detection and correct classification of the munitions and explosives of concern at the direct fire and indirect fire test areas at the UXO Standardized Test Site at the Aberdeen Proving Ground, Maryland in 2010.

Hybrid analysis of multiaxis electromagnetic data for discrimination of munitions and explosives of concern

NASA Astrophysics Data System (ADS)

Friedel, M. J.; Asch, T. H.; Oden, C.

2012-08-01

The remediation of land containing munitions and explosives of concern, otherwise known as unexploded ordnance, is an ongoing problem facing the U.S. Department of Defense and similar agencies worldwide that have used or are transferring training ranges or munitions disposal areas to civilian control. The expense associated with cleanup of land previously used for military training and war provides impetus for research towards enhanced discrimination of buried unexploded ordnance. Towards reducing that expense, a multiaxis electromagnetic induction data collection and software system, called ALLTEM, was designed and tested with support from the U.S. Department of Defense Environmental Security Technology Certification Program. ALLTEM is an on-time time-domain system that uses a continuous triangle-wave excitation to measure the target-step response rather than traditional impulse response. The system cycles through three orthogonal transmitting loops and records a total of 19 different transmitting and receiving loop combinations with a nominal spatial data sampling interval of 20 cm. Recorded data are pre-processed and then used in a hybrid discrimination scheme involving both data-driven and numerical classification techniques. The data-driven classification scheme is accomplished in three steps. First, field observations are used to train a type of unsupervised artificial neural network, a self-organizing map (SOM). Second, the SOM is used to simultaneously estimate target parameters (depth, azimuth, inclination, item type and weight) by iterative minimization of the topographic error vectors. Third, the target classification is accomplished by evaluating histograms of the estimated parameters. The numerical classification scheme is also accomplished in three steps. First, the Biot-Savart law is used to model the primary magnetic fields from the transmitter coils and the secondary magnetic fields generated by currents induced in the target materials in the ground. Second, the target response is modelled by three orthogonal dipoles from prolate, oblate and triaxial ellipsoids with one long axis and two shorter axes. Each target consists of all three dipoles. Third, unknown target parameters are determined by comparing modelled to measured target responses. By comparing the rms error among the self-organizing map and numerical classification results, we achieved greater than 95 per cent detection and correct classification of the munitions and explosives of concern at the direct fire and indirect fire test areas at the UXO Standardized Test Site at the Aberdeen Proving Ground, Maryland in 2010.

Detecting Plastic PFM-1 Butterfly Mines Using Thermal Infrared Sensing

NASA Astrophysics Data System (ADS)

Baur, J.; de Smet, T.; Nikulin, A.

2017-12-01

Remnant plastic-composite landmines, such as the mass-produced PFM-1, represent an ongoing humanitarian threat aggravated by high costs associated with traditional demining efforts. These particular unexploded ordnance (UXO) devices pose a challenge to conventional geophysical detection methods, due their plastic-body design and small size. Additionally, the PFM-1s represent a particularly heinous UXO, due to their low mass ( 25 lb) trigger limit and "butterfly" wing design, earning them the reputation of a "toy mine" - disproportionally impacting children across post-conflict areas. We developed a detection algorithm based on data acquired by a thermal infrared camera mounted to a commercial UAV to detect time-variable temperature difference between the PFM-1 and the surrounding environment. We present results of a field study focused on thermal detection and identification of the PFM-1 anti-personnel landmines from a remotely operated unmanned aerial vehicle (UAV). We conducted a series of field detection experiments meant to simulate the mountainous terrains where PFM-1 mines were historically deployed and remain in place. In our tests, 18 inert PFM-1 mines along with the aluminum KSF-1 casing were randomly dispersed to mimic an ellipsoidal minefield of 8-10 x 18-20 m dimensions in a de-vegetated rubble yard at Chenango Valley State Park (New York State). We collected multiple thermal infrared imagery datasets focused on these model minefields with the FLIR Vue Pro R attached to the 3DR Solo UAV flying at approximately at 2 m. We identified different environmental variables to constrain the optimal time of day and daily temperature variations to reveal presence of these plastic UXOs. We show that in the early-morning hours when thermal inertia is greatest, the PFM-1 mines can be detected based on their differential thermal inertia. Because the mines have statistically different temperatures than background and a characteristic shape, we were able to train a supervised learning algorithm to automate detection of the mines over large areas. We anticipate that following further development, this remote sensing method can aid in significantly reducing the cost and time associated with landmine remediation in post-conflict nations.

Landmine policy in the near-term: a framework for technology analysis and action

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eimerl, D., LLNL

1997-08-01

Any effective solution to the problem of leftover landmines and other post-conflict unexploded ordnance (UXO) must take into account the real capabilities of demining technologies and the availability of sufficient resources to carry out demining operations. Economic and operational factors must be included in analyses of humanitarian demining. These factors will provide a framework for using currently available resources and technologies to complete this task in a time frame that is both practical and useful. Since it is likely that reliable advanced technologies for demining are still several years away, this construct applies to the intervening period. It may alsomore » provide a framework for utilizing advanced technologies as they become available. This study is an economic system model for demining operations carried out by the developed nations that clarifies the role and impact of technology on the economic performance and viability of these operations. It also provides a quantitative guide to assess the performance penalties arising from gaps in current technology, as well as the potential advantages and desirable features of new technologies that will significantly affect the international community`s ability to address this problem. Implications for current and near-term landmine and landmine technology policies are drawn.« less

Visual Sample Plan Version 7.0 User's Guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matzke, Brett D.; Newburn, Lisa LN; Hathaway, John E.

2014-03-01

User's guide for VSP 7.0 This user's guide describes Visual Sample Plan (VSP) Version 7.0 and provides instructions for using the software. VSP selects the appropriate number and location of environmental samples to ensure that the results of statistical tests performed to provide input to risk decisions have the required confidence and performance. VSP Version 7.0 provides sample-size equations or algorithms needed by specific statistical tests appropriate for specific environmental sampling objectives. It also provides data quality assessment and statistical analysis functions to support evaluation of the data and determine whether the data support decisions regarding sites suspected of contamination.more » The easy-to-use program is highly visual and graphic. VSP runs on personal computers with Microsoft Windows operating systems (XP, Vista, Windows 7, and Windows 8). Designed primarily for project managers and users without expertise in statistics, VSP is applicable to two- and three-dimensional populations to be sampled (e.g., rooms and buildings, surface soil, a defined layer of subsurface soil, water bodies, and other similar applications) for studies of environmental quality. VSP is also applicable for designing sampling plans for assessing chem/rad/bio threat and hazard identification within rooms and buildings, and for designing geophysical surveys for unexploded ordnance (UXO) identification.« less

Calibrating a tensor magnetic gradiometer using spin data

USGS Publications Warehouse

Bracken, Robert E.; Smith, David V.; Brown, Philip J.

2005-01-01

Scalar magnetic data are often acquired to discern characteristics of geologic source materials and buried objects. It is evident that a great deal can be done with scalar data, but there are significant advantages to direct measurement of the magnetic gradient tensor in applications with nearby sources, such as unexploded ordnance (UXO). To explore these advantages, we adapted a prototype tensor magnetic gradiometer system (TMGS) and successfully implemented a data-reduction procedure. One of several critical reduction issues is the precise determination of a large group of calibration coefficients for the sensors and sensor array. To resolve these coefficients, we devised a spin calibration method, after similar methods of calibrating space-based magnetometers (Snare, 2001). The spin calibration procedure consists of three parts: (1) collecting data by slowly revolving the sensor array in the Earth?s magnetic field, (2) deriving a comprehensive set of coefficients from the spin data, and (3) applying the coefficients to the survey data. To show that the TMGS functions as a tensor gradiometer, we conducted an experimental survey that verified that the reduction procedure was effective (Bracken and Brown, in press). Therefore, because it was an integral part of the reduction, it can be concluded that the spin calibration was correctly formulated with acceptably small errors.

Cost-Aware Design of a Discrimination Strategy for Unexploded Ordnance Cleanup

DTIC Science & Technology

2011-02-25

Acronyms ANN: Artificial Neural Network AUC: Area Under the Curve BRAC: Base Realignment And Closure DLRT: Distance Likelihood Ratio Test EER...Discriminative Aggregate Nonparametric [25] Artificial Neural Network ANN Discriminative Aggregate Parametric [33] 11 Results and Discussion Task #1

32 CFR 179.2 - Applicability and scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MUNITIONS RESPONSE SITE PRIORITIZATION PROTOCOL (MRSPP) § 179.2 Applicability and scope. (a) This part... ordnance (UXO), discarded military munitions (DMM), or munitions constituents (MC), and (3) That are... munitions results from combat operations, (5) Currently operating military munitions storage and...

32 CFR 179.2 - Applicability and scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... MUNITIONS RESPONSE SITE PRIORITIZATION PROTOCOL (MRSPP) § 179.2 Applicability and scope. (a) This part... ordnance (UXO), discarded military munitions (DMM), or munitions constituents (MC), and (3) That are... munitions results from combat operations, (5) Currently operating military munitions storage and...

32 CFR 179.2 - Applicability and scope.

Code of Federal Regulations, 2014 CFR

2014-07-01

... MUNITIONS RESPONSE SITE PRIORITIZATION PROTOCOL (MRSPP) § 179.2 Applicability and scope. (a) This part... ordnance (UXO), discarded military munitions (DMM), or munitions constituents (MC), and (3) That are... munitions results from combat operations, (5) Currently operating military munitions storage and...

32 CFR 179.2 - Applicability and scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... MUNITIONS RESPONSE SITE PRIORITIZATION PROTOCOL (MRSPP) § 179.2 Applicability and scope. (a) This part... ordnance (UXO), discarded military munitions (DMM), or munitions constituents (MC), and (3) That are... munitions results from combat operations, (5) Currently operating military munitions storage and...

32 CFR 179.2 - Applicability and scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... MUNITIONS RESPONSE SITE PRIORITIZATION PROTOCOL (MRSPP) § 179.2 Applicability and scope. (a) This part... ordnance (UXO), discarded military munitions (DMM), or munitions constituents (MC), and (3) That are... munitions results from combat operations, (5) Currently operating military munitions storage and...

Operator Influence of Unexploded Ordnance Sensor Technologies

DTIC Science & Technology

2007-03-01

chart display ActiveX control Mscomct2.dll – date/time display ActiveX control Pnpscr.dll – Systran SCRAMNet replicated shared memory device...response value database rgm_p2.dll – Phase 2 shared memory API and implementation Commercial components StripM.ocx – strip chart display ActiveX

75 FR 81467 - Safety Zone; Potential Unexploded Ordnance, Pier 91, Seattle, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... evaluate its effects on them and participate in the rulemaking process. Small businesses may send comments... entities. The term ``small entities'' comprises small businesses, not-for-profit organizations that are... Small Entities Under section 213(a) of the Small Business Regulatory Enforcement Fairness Act of 1996...

32 CFR 179.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... effects on human beings, is intended for use in military operations to kill, seriously injure, or..., and emission, degradation, or breakdown elements of such ordnance or munitions. (10 U.S.C. 2710(e)(3..., to address the explosives safety, human health, or environmental risks presented by UXO, discarded...

Tracking Honey Bees Using LIDAR (Light Detection and Ranging) Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

BENDER, SUSAN FAE ANN; RODACY, PHILIP J.; SCHMITT, RANDAL L.

The Defense Advanced Research Projects Agency (DARPA) has recognized that biological and chemical toxins are a real and growing threat to troops, civilians, and the ecosystem. The Explosives Components Facility at Sandia National Laboratories (SNL) has been working with the University of Montana, the Southwest Research Institute, and other agencies to evaluate the feasibility of directing honeybees to specific targets, and for environmental sampling of biological and chemical ''agents of harm''. Recent work has focused on finding and locating buried landmines and unexploded ordnance (UXO). Tests have demonstrated that honeybees can be trained to efficiently and accurately locate explosive signaturesmore » in the environment. However, it is difficult to visually track the bees and determine precisely where the targets are located. Video equipment is not practical due to its limited resolution and range. In addition, it is often unsafe to install such equipment in a field. A technology is needed to provide investigators with the standoff capability to track bees and accurately map the location of the suspected targets. This report documents Light Detection and Ranging (LIDAR) tests that were performed by SNL. These tests have shown that a LIDAR system can be used to track honeybees. The LIDAR system can provide both the range and coordinates of the target so that the location of buried munitions can be accurately mapped for subsequent removal.« less

78 FR 49762 - Desecheo National Wildlife Refuge, PR; Final Comprehensive Conservation Plan and Finding of No...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-15

... complete the removal of all invasive animal species. We will also develop and implement a plan for..., if necessary, efforts to remove invasive species. The number of vegetation plots and frequency of... safety of the refuge regarding the removal of unexploded ordnance. CCP Alternatives, Including Our...

Development and Testing of an Engineering Prototype for a Marine Version of the Berkeley Unexploded Ordnance Discriminator (BUD)

DTIC Science & Technology

2013-06-01

on the laminated waterproof platform as shown in Figures 29 and 30. 35 Figure 29 Figure 30 36 The receiver coils, and transmitter...mounted on a flatbed trailer, transported to the Richmond Marina, and launched from the boat launch ramp, Figure 32. 37 Figure 32 Once in

Innovative Navigation Systems to Support Digital Geophysical Mapping, ESTCP #200129, Phase II Demonstrations

DTIC Science & Technology

2004-09-25

7 Figure 2-3 Blackhawk/ Applanix GPS/INS System...electro-mechanical system ms millisecond NP navigation processor OE ordnance and explosive POSLV Applanix Positioning and Orientation...demonstration GPS/INS positioning system. In Phase II, a man-portable modified version called the POSLV 310 UXO of the Applanix Positioning and

Sea Water Air Conditioning (SWAC) at Naval Base Guam: Cost-Benefit Analysis and Acquisition Strategy

DTIC Science & Technology

2015-03-16

significant impact FWS Fish and Wildlife Service GEPA Guam Environmental Protection Agency GPA Guam Power Authority IPT integrated product team...utility energy service contract USACE U.S. Army Corps of Engineers USCG U.S. Coast Guard UXO unexploded ordinance USFWS U.S. Fish and Wildlife ...its bases, such as wind and solar energy. However, ample room remains for new renewable technologies 3 and cost savings at shore installations

Development of a Spectropolarimetric Remote Sensing Capability

DTIC Science & Technology

2013-03-01

34Review of passive imaging polarimetry for remote sensing applications," Appl. Opt. 45, 5453-5469 (2006). [8] D. B. Chenault, "Infrared...Annen, “Hyperspectral IR polarimetry with application in demining and unexploded ordnance detection,” SPIE Vol. 3534 (1998). [30] Pesses, M... Polarimetry , Fourier Transform Spectrometer, DOLP, Spectropolarimetry, Stokes 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18

Optimization of Integrative Passive Sampling Approaches for Use in the Epibenthic Environment

DTIC Science & Technology

2016-12-23

Passive sampler, POCIS, Integrative, Sediment , Benthic 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 19a...Unexploded ordnance, Passive sampler, POCIS, Integrative, Sediment , Benthic v Acknowledgements Dr. Shane Morrison and Ms. Ingrid...flow and turbulence near the sampler. In complex environments at the sediment – water interface, this may limit the utility of passive sampling

Determining Detection and Classification Potential of Munitions using Advanced EMI Sensors in the Underwater Environment

DTIC Science & Technology

2016-11-01

focuses on characterizing Electromagnetic Induction (EMI) responses in the underwater setting through numerical and experimental studies with the...marine EMI sensing. 15. SUBJECT TERMS Munitions Response, Electromagnetic Induction, Unexploded Ordnance, Classification 16. SECURITY CLASSIFICATION...using Advanced EMI Sensors in the Underwater Environment.” The project focuses on characterizing Electromagnetic Induction (EMI) responses in the

Explosives Dissolved from Unexploded Ordnance

DTIC Science & Technology

2011-10-01

production) HPLC High performance Liquid Chromatography IC Ion conductivity MMR Massachusetts Military Reservation NCDC National Climatic Data Center...rounds, 2) its dissolution rate in water can be measured using ion chromatography or electrical conductivity, and 3) it has a high water solubility...sample access 29 The water samples were analyzed with an ion chromatography system8. The conductivity of each solution is measured and compared

Multi-Sensor Systems Development for UXO Detection and Discrimination: Man-Portable Dual Magnetic/Electromagnetic Induction Sensor

DTIC Science & Technology

2008-02-01

of the magnetic data to constrain the target depth using joint or cooperative inversions ( Pasion et al. 2002). ERDC/EL TR-08-9 24 Figure 15. EM...baseline ordnance classification test site at Blossom Pt. Naval Research Laboratory. NRL/MR/6110-00-8437, March 20, 1998. Pasion , L., S. Billings, and

Sea Water Air Conditioning (SWAC) at Naval Base Guam: Cost-Beneit Analysis and Acquisition Strategy

DTIC Science & Technology

2014-12-01

Fish and Wildlife Service GEPA Guam Environmental Protection Agency GPA Guam Power Authority IPT integrated product team MILCON military...energy service contract USACE U.S. Army Corps of Engineers USCG U.S. Coast Guard UXO unexploded ordinance USFWS U.S. Fish and Wildlife Service WOD13...options for its bases, such as wind and solar energy. However, ample room remains for new renewable technologies 3 and cost savings at shore

Enhancement and Utilization of Airborne Magnetometry for the Detection, Characterization, and Identification of Unexploded Ordance (UXO)

DTIC Science & Technology

2007-07-01

measurement system is based on four GPS antennas rather than a fluxgate magnetometer measurement used in previous generation systems. For the ORAGS...hardware 1 $36,500 Orientation system 1 $16,600 Fluxgate magnetometer 1 $5,300 Navigation system 1 $5,200 Laser altimeter 1 $7,300 Data...1 iii LIST OF FIGURES Page Figure 1. Schematic for the ORAGS-Arrowhead Airborne Total Field Magnetometer System Developed for this Project

Tracing explosives in soil with transcriptional regulators of Pseudomonas putida evolved for responding to nitrotoluenes

PubMed Central

Garmendia, Junkal; De Las Heras, Aitor; Galvão, Teca Calcagno; De Lorenzo, Víctor

2008-01-01

Summary Although different biological approaches for detection of anti‐personnel mines and other unexploded ordnance (UXO) have been entertained, none of them has been rigorously documented thus far in the scientific literature. The industrial 2,4,6 trinitrotoluene (TNT) habitually employed in the manufacturing of mines is at all times tainted with a small but significant proportion of the more volatile 2,4 dinitrotoluene (2,4 DNT) and other nitroaromatic compounds. By using mutation‐prone PCR and DNA sequence shuffling we have evolved in vitro and selected in vivo variants of the effector recognition domain of the toluene‐responsive XylR regulator of the soil bacterium Pseudomonas putida that responds to mono‐, bi‐ and trinitro substituted toluenes. Re‐introduction of such variants in P. putida settled the transcriptional activity of the cognate promoters (Po and Pu) as a function of the presence of nitrotoluenes in the medium. When strains bearing transcriptional fusions to reporters with an optical output (luxAB, GFP) were spread on soil spotted with nitrotoluenes, the signal triggered by promoter activation allowed localization of the target compounds on the soil surface. Our data provide a proof of concept that non‐natural transcription factors evolved to respond to nitroaromatics can be engineered in soil bacteria and inoculated on a target site to pinpoint the presence of explosives. This approach thus opens new ways to tackle this gigantic humanitarian problem. PMID:21261843

Coil design considerations for a high-frequency electromagnetic induction sensing instrument

NASA Astrophysics Data System (ADS)

Sigman, John B.; Barrowes, Benjamin E.; Wang, Yinlin; Bennett, Hollis J.; Simms, Janet E.; Yule, Donald E.; O'Neill, Kevin; Shubitidze, Fridon

2016-05-01

Intermediate electrical conductivity (IEC) materials (101S/m < σ < 104S/m), such as carbon fiber (CF), have recently been used to make smart bombs. In addition, homemade improvised explosive devices (IED) can be produced with low conducting materials (10-4S/m < σ < 1S/m), such as Ammonium Nitrate (AN). To collect unexploded ordnance (UXO) from military training ranges and thwart deadly IEDs, the US military has urgent need for technology capable of detection and identification of subsurface IEC objects. Recent analytical and numerical studies have showed that these targets exhibit characteristic quadrature response peaks at high induction frequencies (100kHz - 15MHz, the High Frequency Electromagnetic Induction (HFEMI) band), and they are not detectable with traditional ultra wideband (UWB) electromagnetic induction (EMI) metal detectors operating between 100Hz - 100kHz. Using the HFEMI band for induction sensing is not so simple as driving existing instruments at higher frequencies, though. At low frequency, EMI systems use more wire turns in transmit and receive coils to boost signal-to-noise ratios (SNR), but at higher frequencies, the transmitter current has non-uniform distribution along the coil length. These non-uniform currents change the spatial distribution of the primary magnetic field and disturb axial symmetry and thwart established approaches for inferring subsurface metallic object properties. This paper discusses engineering tradeoffs for sensing with a broader band of frequencies ever used for EMI sensing, with particular focus on coil geometries.

Market for advanced humanitarian mine detectors

NASA Astrophysics Data System (ADS)

Newnham, Peter; Daniels, David J.

2001-10-01

Uncleared landmines and unexploded ordnance remain a major humanitarian and economic threat in over 60 countries. It is estimated that world wide over US 60 million was spent on mien clearance in 1999. Most of this funding is provided by government aid, often channeled via the UN or European Community. The minefield threat is very varied, with many different types of mien, UXO, terrain and climate type. To cope with this variety a range of demining techniques are used: mechanical techniques such as flails are used for vegetation clearance, however the majority of demining work is still carried out by manual deminers using metal detectors and prodders. Over the last 5 years there has been considerable interest within the scientific and engineering communities in the application of advanced technologies to improve the safety and efficiency of this work. Nevertheless few new products have been introduced into, and accepted by, the demining community. Despite the high political profile of the landmine problem very little e hard dat is available on the real characteristics of the demining equipment market. As part of a European Union supported program to evacuate a multi-sensor handheld mien detector concept, Thales and ERA Technology Ltd have carried out an in-depth assessment of this market. This paper describes the cost- benefits that could accrue to the demining community associated with use of advanced equipment under appropriate conditions and the equipment requirements that result. The dynamics of the demining equipment market and the barriers to entry are discussed.

Military Training: DOD Met Annual Reporting Requirements in Its 2016 Sustainable Ranges Report

DTIC Science & Technology

2016-06-01

domain. Examples include, but are not limited to, endangered species and critical habitat, unexploded ordnance and munitions, radio frequency spectrum...security, (4) threatened and endangered and candidate species , (5) demand for electromagnetic spectrum, (6) continued growth in domestic use of unmanned...Management for Endangered Species Affecting Training Ranges. GAO-03-976. Washington, D.C.: September 29, 2003. Military Training: DOD Approach to

Base Realignment and Closure (BRAC) Environmental Restoration Program Management Plan

DTIC Science & Technology

1999-04-01

ENVIRONMENTAL PROGRAM 5 4.1 Environmental Restoration (Cleanup, Compliance and Unexploded Ordnance) 6 4.2 National Environmental Policy Act (NEPA...Realignment Act) to create a process to close bases and realign the force infrastructure. The law addressed National Environmental Policy Act (NEPA...primarily through provisions contained in the National Defense Authorization Acts for Fiscal Years 1992 through 1997. Appendix A of the BRAC Reuse

Integration of Advanced Statistical Analysis Tools and Geophysical Modeling

DTIC Science & Technology

2010-12-01

Carin Duke University Douglas Oldenburg University of British Columbia Stephen Billings, Leonard Pasion Laurens Beran Sky Research...means and covariances estimated for each class [5]. For this study, dipole polarizabilities were fit with a Pasion -Oldenburg parameterization of 8 −1...model for unexploded ordnance classification with EMI data,” IEEE Geosci. Remote Sensing Letters, vol. 4, pp. 629–633, 2007. [4] L. R. Pasion

Acoustic Identification of Filler Materials in Unexploded Ordnance

DTIC Science & Technology

2006-04-01

PBXN- 103 CH-6 PBXW- 108 Parrafin ( wax ) Baratol (76/24) Plaster TNT Octol (50/50) Comp B PETN Concrete Lo ng itu di na l V el oc ity (m /s ec...26 3.7.3 Identification of Wax fillers...plaster and wax from “other” items including explosives. A series of field tests are described that focus on acoustic measurements on both inert and live

Time Neutron Technique for UXO Discrimination

DTIC Science & Technology

2010-12-01

mixture of TNT and RDX C-4 CFD Composition 4 military plastic explosive Constant Fraction Discriminator Cps CsI counts per second inorganic...Pdfs Probability Density Functions PET Positron Emission Tomography Pfa Probability of False Alarm PFTNA Pulsed Fast/Thermal Neutron Analysis PMTs...the ordnance type (rocket, mortar , projectile, etc.) and what filler material it contains (inert or empty), practice, HE, illumination, chemical (i.e

CORRECTIVE ACTION DECISION DOCUMENT FOR AREA 9 UXO LANDFILL, TONOPAH TEST RNGE, CAU 453, REVISION 0, MARCH 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

none

1998-03-01

This Corrective Action Decision Document (CADD) has been prepared for the Area 9 Unexploded Ordnance (UXO) Landfill (Corrective Action Unit [CAU] 453) in accordance with the Federal Facility Agreement and Consent Order (FFACO) of 1996. Corrective Action Unit 453 is located at the Tonopah Test Range (TTR), Nevada, and is comprised of three individual landfill cells located northwest of Area 9. The cells are listed as one Corrective Action Site (CAS) 09-55-001-0952. The landfill cells have been designated as: � Cell A9-1 � Cell A9-2 � Cell A9-3 The purpose of this CADD is to identify and provide a rationalemore » for the selection of a recommended corrective action alternative for CAU 453. The scope of this CADD consists of the following tasks: � Develop corrective action objectives. � Identify corrective action alternative screening criteria. � Develop corrective action alternatives. � Perform detailed and comparative evaluations of the corrective action alternatives in relation to the corrective action objectives and screening criteria. � Recommend and justify a preferred corrective action alternative for the CAU. In June and July 1997, a corrective action investigation was performed that consisted of activities set forth in the Corrective Action Investigation Plan (CAIP) (DOE/NV, 1997). Subsurface investigation of the soils surrounding the cells revealed no contaminants of concern (COCs) above preliminary action levels. The cell contents were not investigated due to the potential for live UXO. Details concerning the analytical and investigation results can be found in Appendix A of this CADD. Based on the potential exposure pathways, the following corrective action objectives have been identified for CAU 453: � Prevent or mitigate human exposure to subsurface soils containing COCs, solid waste, and/or UXO. � Prevent adverse impacts to groundwater quality. Based on the review of existing data, future land use, and current operations at the TTR, the following alternatives have been developed for consideration at the Area 9 UXO Landfill CAU: � Alternative 1 - No Further Action � Alternative 2 - Closure in Place by Administrative Controls � Alternative 3 - Closure in Place by Capping � Alternative 4 - Clean Closure by Removal The corrective action alternatives were evaluated based on four general corrective action standards and five remedy selection decision factors. Based on the results of this evaluation, Alternative 2, Closure in Place by Administrative Controls, was selected as the preferred corrective action alternative. The preferred corrective action alternative was evaluated on its technical merits, focusing on performance, reliability, feasibility, and safety. The alternative was judged to meet all requirements for the technical components evaluated and to represent the most cost-effective corrective action. The alternative meets all applicable state and federal regulations for closure of the site and will reduce potential future exposure pathways to the contents of the landfill. During corrective action implementation, this alternative will present minimal potential threat to site workers. However, appropriate health and safety procedures will be developed and implemented.« less

Technical Challenges of the U.S. Army’s Ground Combat Vehicle Program

DTIC Science & Technology

2012-11-01

for mine protection and a distinctive armored extension on the top, called the doghouse. Those features optimize it for counterinsurgency operations...vehicles. Less complex approaches have also evolved, such as mines designed to attack the weaker bottoms of vehicles or improvised explosive devices...Improvised Explosive Devices, Suicide Bombers, Unexploded Ordnance, and Mines ,” section I-G-10, “Countermeasures.” See also Clay Wilson, Improvised

Portable Electromagnetic Induction Sensor with Integrated Positioning

DTIC Science & Technology

2013-08-20

Subsurface electromagnetic induction imaging for unexploded ordnance detection. Journal of Applied Geophysics, 79:38 – 45, 2012. ISSN 09269851. URL http...Portable Electromagnetic Induction Sensor with Integrated Positioning MR-1712 Final Report Submitted to Strategic Environmental Research and...19a. NAME OF RESPONSIBLE PERSON 19b. TELEPHONE NUMBER (include area code) Standard Form 298 (Rev. 8–98) Prescribed by ANSI Std. Z39.18 06–25–2013

Regression Analysis as a Cost Estimation Model for Unexploded Ordnance Cleanup at Former Military Installations

DTIC Science & Technology

2002-06-01

fits our actual data . To determine the goodness of fit, statisticians typically use the following four measures: R2 Statistic. The R2 statistic...reviewing instruction, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of...mathematical model is developed to better estimate cleanup costs using historical cost data that could be used by the Defense Department prior to placing

Vehicle-mounted ground penetrating radar (Mine Stalker III) field evaluation in Angola

NASA Astrophysics Data System (ADS)

Laudato, Stephen; Hart, Kerry; Nevard, Michael; Lauziere, Steven; Grant, Shaun

2014-05-01

The U.S. Department of Defense Humanitarian Demining Research and Development (HD R&D) Program, Non-Intrusive Inspection Technology (NIITEK), Inc. and The HALO Trust have over the last decade funded, developed and tested various prototype vehicle mounted ground penetrating radar (GPR) systems named the Mine Stalker. The HD R&D Program and NIITEK developed the Mine Stalker to detect low metal anti-tank (LM-AT) mines in roads. The country of Angola is severely affected by LM-AT mines in and off road, some of which are buried beyond the effective range of detection sensors current used in country. The threat from LM-AT mines such as the South African Number 8 (No. 8) and the Chinese Type 72 (72AT) still persist from Angola's 30 years of civil war. These LM-AT threats are undetectable at depths greater than 5 to 10 centimeters using metal detection technology. Clearing commerce routes are a critical requirement before Angola can rebuild its infrastructure and improve safety conditions for the local populace. The Halo Trust, a non-governmental demining organization (NGO) focused on demining and clearance of unexploded ordnance (UXO), has partnered with the HD R&D Program to conduct an operational field evaluation (OFE) of the Mine Stalker III (MS3) in Angola. Preliminary testing and training efforts yielded encouraging results. This paper presents a review of the data collected, testing results, system limitations and deficiencies while operating in a real world environment. Our goal is to demonstrate and validate this technology in live minefield environments, and to collect data to prompt future developments to the system.

Moving belt metal detector

NASA Astrophysics Data System (ADS)

Nelson, Carl V.; Mendat, Deborah P.; Huynh, Toan B.

2006-05-01

The Johns Hopkins University Applied Physics Laboratory (APL) has developed a prototype metal detection survey system that will increase the search speed of conventional technology while maintaining high sensitivity. Higher search speeds will reduce the time to clear roads of landmines and improvised explosive devices (IED) and to locate unexploded ordnance (UXO) at Base Realignment and Closure (BRAC) sites, thus reducing remediation costs. The new survey sensor system is called the moving belt metal detector (MBMD) and operates by both increasing sensor speed over the ground while maintaining adequate sensor dwell time over the target for good signal-to-noise ratio (SNR) and reducing motion-induced sensor noise. The MBMD uses an array of metal detection sensors mounted on a flexible belt similar to a tank track. The belt motion is synchronized with the forward survey speed so individual sensor elements remain stationary relative to the ground. A single pulsed transmitter coil is configured to provide a uniform magnetic field along the length of the receivers in ground contact. Individual time-domain electromagnetic induction (EMI) receivers are designed to sense a single time-gate measurement of the total metal content. Each sensor module consists of a receiver coil, amplifier, digitizing electronics and a low power UHF wireless transmitter. This paper presents the survey system design concepts and metal detection data from various targets at several survey speeds. Although the laboratory prototype is designed to demonstrate metal detection survey speeds up to 10 m/s, higher speeds are achievable with a larger sensor array. In addition, the concept can be adapted to work with other sensor technologies not previously considered for moving platforms.

Shallow Water UXO Technology Demonstration Site Scoring Record No. 6

DTIC Science & Technology

2007-03-01

ferrous, nonferrous , and mixed metals . The ferrous and nonferrous items have been further divided into three weight zones as presented in Table 1...items are present as well. The mixed- metals clutter is composed of scrap ordnance items or fragments that have both a ferrous and nonferrous ...underwater system using Geonics EM61 High Power (underwater coils) electromagnetic metal detectors (one transmitter coil, three receiver coils). The

Shallow Water UXO Technology Demonstration Site Scoring Record No. 5 (NAEVA/XTECH, EM61 MKII)

DTIC Science & Technology

2008-04-01

been fired or degaussed. Clutter items fit into one of three categories: ferrous, nonferrous , and mixed metals . The ferrous and nonferrous ...electromagnetic (EM) metal detectors . The system was relatively lightweight, requiring a small aluminum boat for towing. This configuration should...composed of ordnance components; however, industrial scrap metal and cultural items are present as well. The mixed- metals clutter is composed of

Magnetic Multi-Scale Mapping to Characterize Anthropogenic Targets

NASA Astrophysics Data System (ADS)

Le Maire, P.; Munschy, M.

2017-12-01

The discovery of buried anthropic objects on construction sites can cause delays and/or dangers for workers and for the public. Indeed, every year 500 tons of Unexploded-ordnance are discovered in France. Magnetic measurements are useful to localize magnetized objects. Moreover, it is the cheapest geophysical method which does not impact environment and which is relatively fast to perform. Fluxgate magnetometers (three components) are used to measure magnetic properties bellow the ground. These magnetic sensors are not absolute, so they need to be calibrated before the onset of the measurements. The advantage is that they allow magnetic compensation of the equipment attached to the sensor. So the choice of this kind sensor gives the opportunity to install the equipment aboard different magnetized supports: boat, quad bike, unmanned aerial vehicle, aircraft,... Indeed, this methodology permits to perform magnetic mapping with different scale and different elevation above ground level. An old French aerial military plant was chosen to perform this multi-scale approach. The advantage of the site is that it contains a lot of different targets with variable sizes and depth, e.g. buildings, unexploded-ordnances of the two world wars, trenches, pipes,… By comparison between the different magnetic anomaly maps at different elevations some of the geometric parameters of the magnetic sources can be characterized. The comparison between measured maps at different elevations and the prolonged map highlights the maximum distance for the target's detection (figure).

Shallow Water UXO Technology Demonstration Site Scoring Record No. 7

DTIC Science & Technology

2007-05-01

categories: ferrous, nonferrous , and mixed metals . The ferrous and nonferrous items are further divided into the three weight zones as presented in... nonferrous component and could reasonably be encountered in a range area. The mixed- metals clutter was placed in the open water area only. TABLE 1-3...Table 1-4, and distributed throughout all test areas. Most of this clutter is composed of ordnance components; however, industrial scrap metal and

Shallow Water UXO Technology Demonstration Site Scoring Record Number 5 (NAEVA/XTECH, EM61 MKII)

DTIC Science & Technology

2007-01-01

Clutter items fit into one of three categories: ferrous, nonferrous , and mixed metals . The ferrous and nonferrous items have been further...fragments that have both a ferrous and nonferrous component and could reasonably be encountered in a range area. The mixed- metals clutter was placed...components; however, industrial scrap metal and cultural items are present as well. The mixed- metals clutter is composed of scrap ordnance items or

Standardized UXO Technology Demonstration Site Scoring Record NO. 934 Technology Type/Platform: EM61 MKII/Towed

DTIC Science & Technology

2009-07-01

nonferrous metallic objects. The applicability of the instrument for ordnance and explosives (OE) detection has been widely demonstrated at sites...was cleared of all metallic items. This clearing of the metallic anomalies from the 2 acre Active Response Demonstration Site was broken into three...with their Multiple Towed Array Detection System (MTADS). This system is known for its effectiveness and ability to detect metallic items. Once the

A Man-Portable Vector Sensor for Identification of Unexploded Ordnance

DTIC Science & Technology

2011-08-24

Hanover data of Section III-B2, and Dr. L. Pasion , J. Jacobson, and H. Ngo of Sky Research and Dr. L.-P. Song of the University of British Columbia for...of equivalent dipole polarizabilities in situ,” IEEE Trans. Geosci. Remote Sens., vol. 43, no. 7, pp. 1490–1498, Jul. 2005. [27] L. R. Pasion and D. W...P. Song, F. Shubitidze, L. R. Pasion , D. W. Oldenburg, and S. D. Billings, “Computing transient electromagnetic responses of a metallic object using

Next Generation Data Collection System for Mobile Detection and Discrimination of Unexploded Ordnance

DTIC Science & Technology

2008-09-10

parametric form in which the i−th principal polarization is given by Li(t) = kit −βie− t γi ( Pasion and Oldenburg, 2001). The model parameters m contain the lo...66 September 2008 6 REFERENCES Billings, S. D., Pasion , L. R., Beran, L., Oldenburg, D., Sinex, D., Song, L., Lhomme, N., 2007, ESTCP MM-0504...Office. Billings, S. D., Pasion , L. R., Beran, L., Oldenburg, D., Sinex, D., Song, L., Lhomme, N., 2008, ESTCP MM-0504, Practical Discrimination

Unexploded Ordnance Clearance: A Coordinated Approach to Requirements and Technology Development.

DTIC Science & Technology

1997-03-25

ID #23) Clear mines and obstacles in a 50-meter-wide lane through the surf H N N N N zone and beach in order to land Landing Craft Air Cushion (LCAC...ID #33) Clear the surf zone (SZ) and beach zone (BZ) of mines and H N L N N obstacles in order to land LCAC during amphibious assaults and...Range Clearance All areas Commercial Off The Shelf (COTS) or military adapted -equipment, EOD technicians, DoD civilians, locally hired service

Shallow Water UXO Technology Demonstration Site Scoring Record Number 4 (CTC, FEREX, DLG-GPS, MAG)

DTIC Science & Technology

2007-01-01

into one of three categories: ferrous, nonferrous , and mixed- metals . The ferrous and nonferrous items have been further divided into three weight...ferrous and nonferrous component and could reasonably be encountered in a range area. The mixed- metals clutter was placed in the open water area...also industrial scrap metal and cultural items as well. The mixed- metals clutter is comprised of scrap ordnance items or fragments that have both a

Ultra-Wideband EMI Sensing: Non-Metallic Target Detection and Automatic Classification of Unexploded Ordnance

NASA Astrophysics Data System (ADS)

Sigman, John Brevard

Buried explosive hazards present a pressing problem worldwide. Millions of acres and thousands of sites are contaminated in the United States alone [1, 2]. There are three categories of explosive hazards: metallic, intermediate-electrical conducting (IEC), and non-conducting targets. Metallic target detection and classification by electromagnetic (EM) signature has been the subject of research for many years. Key to the success of this research is modern multi-static Electromagnetic Induction (EMI) sensors, which are able to measure the wideband EMI response from metallic buried targets. However, no hardware solutions exist which can characterize IEC and non-conducting targets. While high-conducting metallic targets exhibit a quadrature peak response for frequencies in a traditional EMI regime under 100 kHz, the response of intermediate-conducting objects manifests at higher frequencies, between 100 kHz and 15 MHz. In addition to high-quality electromagnetic sensor data and robust electromagnetic models, a classification procedure is required to discriminate Targets of Interest (TOI) from clutter. Currently, costly human experts are used for this task. This expense and effort can be spared by using statistical signal processing and machine learning. This thesis has two main parts. In the first part, we explore using the high frequency EMI (HFEMI) band (100 kHz-15 MHz) for detection of carbon fiber UXO, voids, and of materials with characteristics that may be associated with improvised explosive devices (IED). We constructed an HFEMI sensing instrument, and apply the techniques of metal detection to sensing in a band of frequencies which are the transition between the induction and radar bands. In this transition domain, physical considerations and technological issues arise that cannot be solved via the approaches used in either of the bracketing lower and higher frequency ranges. In the second half of this thesis, we present a procedure for automatic classification of UXO. For maximum generality, our algorithm is robust and can handle sparse training examples of multi-class data. This procedure uses an unsupervised starter, semi-supervised techniques to gather training data, and concludes with supervised learning until all TOI are found. Additionally, an inference method for estimating the number of remaining true positives from a partial Receiver Operating Characteristic (ROC) curve is presented and applied to live-site dig histories.

Shallow Water UXO Technology Demonstration Site Scoring Record No. 1. Technology Type/Platform: GEN-3 Array

DTIC Science & Technology

2008-04-01

Clutter items fit into one of three categories: ferrous, nonferrous , and mixed metals . The ferrous and nonferrous items have been further divided into...that have both a ferrous and nonferrous component and could reasonably be encountered in a range area. The mixed- metals clutter was placed in the...however, there are also industrial scrap metal and cultural items as well. The mixed- metals clutter is comprised of scrap ordnance items or fragments

Robust Statistics and Regularization for Feature Extraction and UXO Discrimination

DTIC Science & Technology

2011-07-01

July 11, 2011 real data we find that this technique has an improved probability of finding all ordnance in a test data set, relative to previously...many sites. Tests on larger data sets should still be carried out. In previous work we considered a bootstrapping approach to selecting the operating...Marginalizing over x we obtain the probability that the ith order statistic in the test data belongs to the T class (55) P (T |x(i)) = ∞∫ −∞ P (T |x)p(x

Remedial Action Report for Operable Units 6-05 and 10-04, Phase III

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. P. Wells

2007-08-15

This Phase III remedial action report addresses the remediation of lead-contaminated soils found at the Security Training Facility STF-02 Gun Range at the Idaho National Laboratory Site. Phase I, consisting of developing and implementing institutional controls at Operble Unit 10-04 sites and developing and implementing Idaho National Laboratory Site-wide plans for both institutional controls and ecological monitoring, was addressed in a previous report. Phase II will remediate sites contaminated with trinitrotoluene and Royal Demolition Explosive. Phase IV will remediate hazards from unexploded ordnance.

Development and Evaluation of an Airborne Superconducting Quantum Interference Device-Based Magnetic Gradiometer Tensor System for Detection, Characterization and Mapping of Unexploded Ordnance

DTIC Science & Technology

2008-08-01

Figure 17: USGS Helmholtz coils with SQUID and fluxgate magnetometers installed. 22 Figure 18: Plot of SQUID and fluxgate data from a rotating... fluxgate magnetometer , each sensor measures flux in only one direction. Combinations of SQUID sensor elements are arranged in various configurations...than the absolute field value the way that a fluxgate magnetometer would do. If the SQUID is shut down or loses lock, it has no way to relate the new

Use of nuclear techniques to determine the fill of found unexploded ordnance.

PubMed

Steward, Scott; Forsht, Denice

2005-01-01

The PELAN is a man-portable device that uses pulsed neutrons to interrogate objects in order to determine their filler. The neutrons initiate several types of nuclear reactions within the object under scrutiny, which result in the formation of gamma rays. The energy of the resulting gamma rays provides information about the elements (carbon, hydrogen, oxygen, nitrogen) contained within the object; in addition the number of gamma rays detected provides information about how much of each element is present. An analysis of the elements present and their ratios to one another allows for identification of the filler material.

Attribution of soil information associated with modeling background clutter

NASA Astrophysics Data System (ADS)

Mason, George; Melloh, Rae

2006-05-01

This paper examines the attribution of data fields required to generate high resolution soil profiles for support of Computational Test Bed (CTB) used for countermine research. The countermine computational test bed is designed to realistically simulate the geo-environment to support the evaluation of sensors used to locate unexploded ordnance. The goal of the CTB is to derive expected moisture, chemical compounds, and measure heat migration over time, from which we expect to optimize sensor performance. Several tests areas were considered for the collection of soils data to populate the CTB. Collection of bulk soil properties has inherent spatial resolution limits. Novel techniques are therefore required to populate a high resolution model. This paper presents correlations between spatial variability in texture as related to hydraulic permeability and heat transfer properties of the soil. The extracted physical properties are used to exercise models providing a signature of subsurface media and support the simulation of detection by various sensors of buried and surface ordnance.

A method for real time detecting of non-uniform magnetic field

NASA Astrophysics Data System (ADS)

Marusenkov, Andriy

2015-04-01

The principle of measuring magnetic signatures for observing diverse objects is widely used in Near Surface work (unexploded ordnance (UXO); engineering & environmental; archaeology) and security and vehicle detection systems as well. As a rule, the magnitude of the signals to be measured is much lower than that of the quasi-uniform Earth magnetic field. Usually magnetometers for these purposes contain two or more spatially separated sensors to estimate the full tensor gradient of the magnetic field or, more frequently, only partial gradient components. The both types (scalar and vector) of magnetic sensors could be used. The identity of the scale factors and proper alignment of the sensitivity axes of the vector sensors are very important for deep suppression of the ambient field and detection of weak target signals. As a rule, the periodical calibration procedure is used to keep matching sensors' parameters as close as possible. In the present report we propose the technique for detection magnetic anomalies, which is almost insensitive to imperfect matching of the sensors. This method based on the idea that the difference signals between two sensors are considerably different when the instrument is rotated or moved in uniform and non-uniform fields. Due to the misfit of calibration parameters the difference signal observed at the rotation in the uniform field is similar to the total signal - the sum of the signals of both sensors. Zero change of the difference and total signals is expected, if the instrument moves in the uniform field along a straight line. In contrast, the same move in the non-uniform field produces some response of each of the sensors. In case one measures dB/dx and moves along x direction, the sensors signals is shifted in time with the lag proportional to the distance between sensors and the speed of move. It means that the difference signal looks like derivative of the total signal at move in the non-uniform field. So, using quite simple electronic schematic it is possible to detect the lag between the total and difference signals and to trigger alarms, when the instrument passes near a magnetized object. The proposed method was successfully applied in the two instruments: the low-power search coil magnetometer for vehicle detection system and the low-noise flux-gate magnetometer for magnetocardiograph. Author believes that this approach could be also useful for the fast inspection of the area during the engineering, archaeology, UXO surveys.

Underwater olfaction for real-time detection of submerged unexploded ordnance

NASA Astrophysics Data System (ADS)

Harper, Ross J.; Dock, Matthew L.

2007-04-01

The presence of Underwater Unexploded Ordnance (UUXO) represents a considerable threat in the marine environment. Elevated concentrations of dissolved explosive compounds, such as TNT and RDX, may be produced in the vicinity of degraded UUXO shell casings and are known to have significant toxicant effects on local marine organisms. During World War II and in subsequent years, the US military inadvertently or, in some cases intentionally, deposited many thousands of tons of UUXO in US coastal waters. Much of this material is difficult to locate by magnetometry or sonar imaging techniques, and can be extremely challenging to identify by visual means after lying on the bottom of the ocean for several decades. The present work is focused on advances in underwater olfaction, wherein trace amounts of dissolved explosive compounds may be detected and discriminated from other chemical species found in the marine environment, for the purpose of establishing safe cordons and/or neutralization of the explosives. ICx Nomadics has developed the first known real-time sensor system that is capable of detecting chemical signatures emanating from underwater explosives. The SeaPup sensor, which is based on the fluorescence-quenching transduction mechanism of an amplifying fluorescent polymer (AFP), is capable of real-time detection of the trace chemical signatures emanating from submerged explosive compounds. The SeaPup system has been successfully tested on various marine platforms, including a crawler robot, an autonomous underwater vehicle (AUV), and a remotely operated underwater vehicle (ROV). In one study, the SeaPup was shown to effectively map liquid phase "explosive scent plumes" emanating from an underwater source of TNT. The presented paper will provide an overview of the history, current status, and future development of explosive analyte detection in the underwater environment.

Resolution Enhanced Magnetic Sensing System for Wide Coverage Real Time UXO Detection

NASA Astrophysics Data System (ADS)

Zalevsky, Zeev; Bregman, Yuri; Salomonski, Nizan; Zafrir, Hovav

2012-09-01

In this paper we present a new high resolution automatic detection algorithm based upon a Wavelet transform and then validate it in marine related experiments. The proposed approach allows obtaining an automatic detection in a very low signal to noise ratios. The amount of calculations is reduced, the magnetic trend is depressed and the probability of detection/ false alarm rate can easily be controlled. Moreover, the algorithm enables to distinguish between close targets. In the algorithm we use the physical dependence of the magnetic field of a magnetic dipole in order to define a Wavelet mother function that later on can detect magnetic targets modeled as dipoles and embedded in noisy surrounding, at improved resolution. The proposed algorithm was realized on synthesized targets and then validated in field experiments involving a marine surface-floating system for wide coverage real time unexploded ordinance (UXO) detection and mapping. The detection probability achieved in the marine experiment was above 90%. The horizontal radial error of most of the detected targets was only 16 m and two baseline targets that were immersed about 20 m one to another could easily be distinguished.

Physics based Prediction of Unexploded Ordnance Penetration in Granular Materials

DTIC Science & Technology

2017-05-01

0.08 0.10 0.12 0.14 0.16 0.18 D is pl ac em en t ( m m ) Time (s) Simulation Centrifuge test 91 cylindrical DSE assembly, and the shape of the stress...0.18 D is pl ac em en t ( m m ) Time (s) Simulation Centrifuge test 96 a) b) c) d) Figure 5.21 Projectile penetration simulation vertical...penetration (Fig. 5.25c and Fig. 5.26c). -4000 -3500 -3000 -2500 -2000 -1500 -1000 -500 0 0.00 0.02 0.04 0.06 0.08 0.10 D is pl ac em en t ( m m

Detection and characterisation of anthropogenic pieces by magnetic method

NASA Astrophysics Data System (ADS)

Nodot, Emilie; Munschy, Marc; Benevent, Pierre

2013-04-01

Human activities have let many anthropogenic objects buried under our feet. Some of these like explosive devices left after the World Wars turn out to be a threat to safety or environment. Others must be perfectly localised in case of construction work, for example gas pipe. Geophysics and more specifically magnetic cartography (many of these items are magnetic) can obviously help to locate them. We already use this method on daily basis to detect UXO (unexploded ordnance) but less than 10% of the unearthed objects are actually bombs or shells. Detection and mostly characterisation methods must be improved in order to reduce this proportion. On the field there are a few things we can do to increase data qualities. Characterisation may be improved by multiple scale prospections. We search a large area with our usual and rather fast method then we achieve high definition cartographies of small interesting areas (upon the object to characterise). In the case of measurements in an urban environment for example, data are distorted. The traffic (train, tramway, cars…) produces temporal variations of the magnetic field. This effect can be lessened, sometimes even removed by the use of a fixed scalar magnetic sensor. Data treatment is another key as regards the characterisation. Tools such as analytic signal or derivative are frequently used at the first degree. We will see that in a synthetic case the second and third degree bring even more information. A new issue appeared recently about pipes. Can we localise very precisely (less than 10 cm uncertainty) a gas pipe? Horizontally we can but due to our inversion method we still have troubles with the depth accuracy. Our final concern is about the amplitude of some anomalies. Potential methods equations are based on the fact that the anomaly norm must be minor to magnetic field norm. Sometimes this is not the case but vector magnetometry is a lead to solve this problem.

Observation of Burial and Migration of Instrumented Surrogate Munitions Deployed in the Swash Zone

NASA Astrophysics Data System (ADS)

Cristaudo, D.; Puleo, J. A.; Bruder, B. L.

2017-12-01

Munitions (also known as unexploded ordnance; UXO) in the nearshore environment due to past military activities, may be found on the beach, constituting a risk for beach users. Munitions may be transported from offshore to shallower water and/or migrate along the coast. In addition, munitions may bury in place or be exhumed due to hydrodynamic forcing. Observations on munitions mobility have generally been collected offshore, while observations in the swash zone are scarce. The swash zone is the region of the beach alternately covered by wave runup where hydrodynamic processes may be intense. Studies of munitions mobility require the use of realistic surrogates to quantify mobility/burial and hydrodynamic forcing conditions. Four surrogates (BLU-61 Cluster Bomb, 81 mm Mortar, M151-70 Hydra Rocket and M107 155 mm High Explosive Howitzer) were developed and tested during large-scale laboratory and field studies. Surrogates house sensors that measure different components of motion. Errors between real munitions and surrogate parameters (mass, center of gravity and axial moment of inertia) are all within an absolute error of 20%. Internal munitions sensors consist of inertial motion units (for acceleration and angular velocity in and around the three directions and orientation), pressure transducers (for water depth above surrogate), shock recorders (for high frequency acceleration to detect wave impact on the surrogate), and an in-house designed array of optical sensors (for burial/exposure and rolling). An in situ array of sensors to measure hydrodynamics, bed morphology and sediment concentrations, was deployed in the swash zone, aligned with the surrogate deployment. Data collected during the studies will be shown highlighting surrogate sensor capabilities. Sensors response will be compared with GPS measurements and imagery from cameras overlooking the study sites of surrogate position as a function of time. Examples of burial/exposure and migration of surrogates will be discussed. Relationships between burial/migration and incoming forcing conditions, bed slope and munitions characteristics (such as specific density, length/diameter) will all be shown.

Predictions and Observations of Munitions Burial Under Intense Storm Waves at Duck, NC

NASA Astrophysics Data System (ADS)

Calantoni, J.; Klammer, H.; Sheremet, A.

2017-12-01

The fate of munitions or unexploded ordnance (UXO) resting on a submarine sediment bed is a critical safety concern. Munitions may remain in place or completely disappear for significant but unknown periods, after becoming buried in the sediment bed. Clearly, burial of munitions drastically complicates the detection and removal of potential threats. Here, we present field data of wave height and surrogate munitions burial depths near the 8-m isobath at the U.S. Army Corps of Engineers, Field Research Facility, Duck, North Carolina, observed between January and March 2015. The experiment captured a remarkable sequence of storms that included at least 10 events, of which 6 were characterized by wave fields of significant heights exceeding 2 m and with peak periods of approximately 10 s. During the strongest storm, waves of 14 s period and heights exceeding 2 m were recorded for more than 3 days; significant wave height reached 5 m at the peak of activity. At the end of the experiment, divers measured munition burial depths of up to 60 cm below the seabed level. However, the local bathymetry showed less than 5 cm variation between the before and after-storm states, suggesting the local net sediment accumulation / loss was negligible. The lack of bathymetric variability strongly suggests that the munitions sank into the bed, which would suggest an extreme state of sand agitation during the storm. We explore existing analytical solutions for the dynamic interaction between waves and sediment to predict munitions burial depths. Measured time series of wave pressure near the sediment bed were converted into wave-induced changes in pore pressures and the effective stress states of the sediment. Different sediment failure criteria based on minimum normal and maximum shear stresses were then applied to evaluate the appropriateness of individual failure criteria to predict observed burial depths. Results are subjected to a sensitivity analysis with respect to uncertain sediment parameters and summarized by representing cumulative failure times as a function of depth.

Underwater object classification using scattering transform of sonar signals

NASA Astrophysics Data System (ADS)

Saito, Naoki; Weber, David S.

2017-08-01

In this paper, we apply the scattering transform (ST)-a nonlinear map based off of a convolutional neural network (CNN)-to classification of underwater objects using sonar signals. The ST formalizes the observation that the filters learned by a CNN have wavelet-like structure. We achieve effective binary classification both on a real dataset of Unexploded Ordinance (UXOs), as well as synthetically generated examples. We also explore the effects on the waveforms with respect to changes in the object domain (e.g., translation, rotation, and acoustic impedance, etc.), and examine the consequences coming from theoretical results for the scattering transform. We show that the scattering transform is capable of excellent classification on both the synthetic and real problems, thanks to having more quasi-invariance properties that are well-suited to translation and rotation of the object.

Closure Report for Corrective Action Unit 408: Bomblet Target Area Tonopah Test Range (TTR), Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark Krauss

2010-09-01

This Closure Report (CR) presents information supporting the closure of Corrective Action Unit (CAU) 408: Bomblet Target Area (TTR), Tonopah Test Range, Nevada. This CR complies with the requirements of the Federal Facility Agreement and Consent Order that was agreed to by the State of Nevada; U.S. Department of Energy (DOE), Environmental Management; U.S. Department of Defense; and DOE, Legacy Management. Corrective Action Unit 408 is located at the Tonopah Test Range, Nevada, and consists of Corrective Action Site (CAS) TA-55-002-TAB2, Bomblet Target Areas. This CAS includes the following seven target areas: • Mid Target • Flightline Bomblet Location •more » Strategic Air Command (SAC) Target Location 1 • SAC Target Location 2 • South Antelope Lake • Tomahawk Location 1 • Tomahawk Location 2 The purpose of this CR is to provide documentation supporting the completed corrective actions and data confirming that the closure objectives for the CAS within CAU 408 were met. To achieve this, the following actions were performed: • Review the current site conditions, including the concentration and extent of contamination. • Implement any corrective actions necessary to protect human health and the environment. • Properly dispose of corrective action and investigation wastes. • Document Notice of Completion and closure of CAU 408 issued by the Nevada Division of Environmental Protection. From July 2009 through August 2010, closure activities were performed as set forth in the Streamlined Approach for Environmental Restoration Plan for CAU 408: Bomblet Target Area, Tonopah Test Range (TTR), Nevada. The purposes of the activities as defined during the data quality objectives process were as follows: • Identify and remove munitions of explosive concern (MEC) associated with DOE activities. • Investigate potential disposal pit locations. • Remove depleted uranium-contaminated fragments and soil. • Determine whether contaminants of concern (COCs) are present. • If COCs are present, determine their nature and extent, implement appropriate corrective actions, and properly dispose of wastes. Analytes detected during the closure activities were evaluated against final action levels to determine COCs for CAU 408. Assessment of the data indicated COCs are not present at CAS TA-55-002-TAB2; therefore, no corrective action is necessary. No use restrictions are required to be placed on this CAU because the investigation showed no evidence of remaining soil contamination or remaining debris/waste upon completion of all investigation activities. The MEC was successfully removed and dispositioned as planned using current best available technologies. As MEC guidance and general MEC standards acknowledge that MEC response actions cannot determine with 100 percent certainty that all MEC and unexploded ordnance (UXO) are removed, the clean closure of CAU 408 will implement a best management practice of posting UXO hazard warning signs near the seven target areas. The signs will warn future land users of the potential for encountering residual UXO hazards. The DOE, National Nuclear Security Administration Nevada Site Office, provides the following recommendations: • A Notice of Completion to the DOE, National Nuclear Security Administration Nevada Site Office, is requested from the Nevada Division of Environmental Protection for closure of CAU 408. • Corrective Action Unit 408 should be moved from Appendix III to Appendix IV of the Federal Facility Agreement and Consent Order.« less

Prediction and observation of munitions burial in energetic storms

NASA Astrophysics Data System (ADS)

Klammler, Harald; Sheremet, Alexandru; Calantoni, Joseph

2017-04-01

The fate of munitions or unexploded ordnance (UXO) resting on a submarine sediment bed is a critical safety concern. Munitions may be transported in uncontrolled ways to create potentially dangerous situations at places like beaches or ports. Alternatively, they may remain in place or completely disappear for significant but unknown periods, after becoming buried in the sediment bed. Clearly, burial of munitions drastically complicates the detection and removal of potential threats. Here, we present field data of wave height and (surrogate) munitions burial depths near the 8-m isobath at the U.S. Army Corps of Engineers, Field Research Facility, Duck, North Carolina, observed between January and March 2015. The experiment captured a remarkable sequence of storms that included at least 10 events, of which 6 were characterized by wave fields of significant heights exceeding 2 m and with peak periods of approximately 10 s. During the strongest storm, waves of 14 s period and heights exceeding 2 m were recorded for more than 3 days; significant wave height reached 5 m at the peak of activity. At the end of the experiment, divers measured munition burial depths of up to 60 cm below the seabed level. However, the local bathymetry showed less than 5 cm variation between the before and after-storm states, suggesting the local net sediment accumulation / loss was negligible. The lack of bathymetric variability excludes the possibility of burial by a migrating bed form or by sediment deposition, and strongly indicates that the munitions sank into the bed. The depth of burial also suggest an extreme state of sand agitation during the storm. For predicting munitions burial depths, we explore existing analytical solutions for the dynamic interaction between waves and sediment. Measured time series of wave pressure near the sediment bed were converted into wave-induced changes in pore pressures and the effective stress states of the sediment. Different sediment failure criteria based on minimum normal and maximum shear stresses are then applied to evaluate the appropriateness of individual failure criteria to predict observed burial depths. Results are subjected to a sensitivity analysis with respect to uncertain sediment parameters and summarized by representing cumulative failure times as a function of depth.

Use of an UROV to develop 3-D optical models of submarine environments

NASA Astrophysics Data System (ADS)

Null, W. D.; Landry, B. J.

2017-12-01

The ability to rapidly obtain high-fidelity bathymetry is crucial for a broad range of engineering, scientific, and defense applications ranging from bridge scour, bedform morphodynamics, and coral reef health to unexploded ordnance detection and monitoring. The present work introduces the use of an Underwater Remotely Operated Vehicle (UROV) to develop 3-D optical models of submarine environments. The UROV used a Raspberry Pi camera mounted to a small servo which allowed for pitch control. Prior to video data collection, in situ camera calibration was conducted with the system. Multiple image frames were extracted from the underwater video for 3D reconstruction using Structure from Motion (SFM). This system provides a simple and cost effective solution to obtaining detailed bathymetry in optically clear submarine environments.

Polarization differences in airborne ground penetrating radar performance for landmine detection

NASA Astrophysics Data System (ADS)

Dogaru, Traian; Le, Calvin

2016-05-01

The U.S. Army Research Laboratory (ARL) has investigated the ultra-wideband (UWB) radar technology for detection of landmines, improvised explosive devices and unexploded ordnance, for over two decades. This paper presents a phenomenological study of the radar signature of buried landmines in realistic environments and the performance of airborne synthetic aperture radar (SAR) in detecting these targets as a function of multiple parameters: polarization, depression angle, soil type and burial depth. The investigation is based on advanced computer models developed at ARL. The analysis includes both the signature of the targets of interest and the clutter produced by rough surface ground. Based on our numerical simulations, we conclude that low depression angles and H-H polarization offer the highest target-to-clutter ratio in the SAR images and therefore the best radar performance of all the scenarios investigated.

Realistic Subsurface Anomaly Discrimination Using Electromagnetic Induction and an SVM Classifier

NASA Astrophysics Data System (ADS)

Pablo Fernández, Juan; Shubitidze, Fridon; Shamatava, Irma; Barrowes, Benjamin E.; O'Neill, Kevin

2010-12-01

The environmental research program of the United States military has set up blind tests for detection and discrimination of unexploded ordnance. One such test consists of measurements taken with the EM-63 sensor at Camp Sibert, AL. We review the performance on the test of a procedure that combines a field-potential (HAP) method to locate targets, the normalized surface magnetic source (NSMS) model to characterize them, and a support vector machine (SVM) to classify them. The HAP method infers location from the scattered magnetic field and its associated scalar potential, the latter reconstructed using equivalent sources. NSMS replaces the target with an enclosing spheroid of equivalent radial magnetization whose integral it uses as a discriminator. SVM generalizes from empirical evidence and can be adapted for multiclass discrimination using a voting system. Our method identifies all potentially dangerous targets correctly and has a false-alarm rate of about 5%.

Remotely controlled sensor apparatus for use in dig-face characterization system

DOEpatents

Josten, N.E.; Svoboda, J.M.

1999-05-25

A remotely controlled sensor platform apparatus useful in a dig-face characterization system is deployed from a mobile delivery device such as standard heavy construction equipment. The sensor apparatus is designed to stabilize sensors against extraneous motions induced by heavy equipment manipulations or other outside influences, and includes a terrain sensing and sensor elevation control system to maintain the sensors in close ground proximity. The deployed sensor apparatus is particularly useful in collecting data in work environments where human access is difficult due to the presence of hazardous conditions, rough terrain, or other circumstances that prevent efficient data collection by conventional methods. Such work environments include hazardous waste sites, unexploded ordnance sites, or construction sites. Data collection in these environments by utilizing the deployed sensor apparatus is desirable in order to protect human health and safety, or to assist in planning daily operations to increase efficiency. 13 figs.

Remotely controlled sensor apparatus for use in dig-face characterization system

DOEpatents

Josten, Nicholas E.; Svoboda, John M.

1999-01-01

A remotely controlled sensor platform apparatus useful in a dig-face characterization system is deployed from a mobile delivery device such as standard heavy construction equipment. The sensor apparatus is designed to stabilize sensors against extraneous motions induced by heavy equipment manipulations or other outside influences, and includes a terrain sensing and sensor elevation control system to maintain the sensors in close ground proximity. The deployed sensor apparatus is particularly useful in collecting data in work environments where human access is difficult due to the presence of hazardous conditions, rough terrain, or other circumstances that prevent efficient data collection by conventional methods. Such work environments include hazardous waste sites, unexploded ordnance sites, or construction sites. Data collection in these environments by utilizing the deployed sensor apparatus is desirable in order to protect human health and safety, or to assist in planning daily operations to increase efficiency.

Development of Defoamers for Confinenment Foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D M; Mitchell, A R

Aqueous foam concentrate (AFC) 380 foam was developed by Sandia National Laboratory as a blast mitigation foam for unexploded ordnance (UXO) and its ''engineered foam structure'' is reported to be able to ''envelop chemical or biological aerosols'' [1]. It is similar to commercial fire-fighting foams, consisting mostly of water with small amounts of two alcohols, an ether and surfactant. It also contains xanthan gum, probably, to strengthen the foam film and delay drainage. The concentrate is normally diluted in a 6:94 ratio with water for foaming applications. The diluted solution is normally foamed with air to an expansion factor ofmore » about 100 (density 0.01 g/cc), which is called ''dry'' foam. Higher density foam (0.18 > {rho} > 0.03 g/cc) was discovered which had quite different characteristics from ''dry'' foam and was called ''wet'' foam. Some characterization of these foams has also been carried out, but the major effort described in this document is the evaluation, at the small and medium scale, of chemical, mechanical and thermal approaches to defoaming AFC 380 foam. Several chemical approaches to defoaming were evaluated including oxidation and precipitation of the xanthan, use of commercial oil-emulsion or suspension defoamers, pH modification, and cation exchange with the surfactant. Of these the commercial defoamers were most effective. Two mechanical approaches to defoaming were evaluated: pressure and foam rupture with very fine particles. Pressure and vacuum techniques were considered too difficult for field applications but high surface area silica particles worked very well on dry foam. Finally simple thermal techniques were evaluated. An order-disorder transition occurs in xanthan solutions at about 60 C, which may be responsible for the effectiveness of hot air as a defoamer. During defoaming of 55 gallons of foam with hot air, after about 70% of the AFC 380 foam had been defoamed, the effectiveness of hot air was dramatically reduced. Approximately 15 gal of residual foam containing mostly small bubbles was resistant to further defoaming by methods that had been effective on the original, dry foam. In this paper the residual foam is referred to as ''wet'' and the original foam is referred to as ''dry''. Methods for generating ''wet'' foam in small to moderate quantities for defoaming experiments have been developed. Methods for defoaming wet foam are currently under study.« less

Development and demonstration of a telerobotic excavation system

NASA Technical Reports Server (NTRS)

Burks, Barry L.; Thompson, David H.; Killough, Stephen M.; Dinkins, Marion A.

1994-01-01

Oak Ridge National Laboratory is developing remote excavation technologies for the Department of Energy's Office (DOE) of Technology Development, Robotics Technology Development Program, and also for the Department of Defense (DOD) Project Manager for Ammunition Logistics. This work is being done to meet the need for remote excavation and removal of radioactive and contaminated buried waste at several DOE sites and unexploded ordnance at DOD sites. System requirements are based on the need to uncover and remove waste from burial sites in a way that does not cause unnecessary personnel exposure or additional environmental contamination. Goals for the current project are to demonstrate dexterous control of a backhoe with force feedback and to implement robotic operations that will improve productivity. The Telerobotic Small Emplacement Excavator is a prototype system that incorporates the needed robotic and telerobotic capabilities on a commercially available platform. The ability to add remote dexterous teleoperation and robotic operating modes is intended to be adaptable to other commercially available excavator systems.

Kuwaiti reconstruction project unprecedented in size, complexity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tippee, B.

1993-03-15

There had been no challenge like it: a desert emirate ablaze; its main city sacked; the economically crucial oil industry devastated; countryside shrouded in smoke from oil well fires and littered with unexploded ordnance, disabled military equipment, and unignited crude oil. Like the well-documented effort that brought 749 burning wells under control in less than 7 months, Kuwaiti reconstruction had no precedent. Unlike the firefight, reconstruction is no-where complete. It nevertheless has placed two of three refineries back on stream, restored oil production to preinvasion levels, and repaired or rebuilt 17 of 26 oil field gathering stations. Most of themore » progress has come since the last well fire went out on Nov. 6, 1991. Expatriates in Kuwait since the days of Al-Awda- the return,' in Arabic- attribute much of the rapid progress under Al-Tameer- the reconstruction'- to decisions and preparations made while the well fires still raged. The article describes the planning for Al-Awda, reentering the country, drilling plans, facilities reconstruction, and special problems.« less

Superconductivity and the environment: a Roadmap

NASA Astrophysics Data System (ADS)

Nishijima, Shigehiro; Eckroad, Steven; Marian, Adela; Choi, Kyeongdal; Kim, Woo Seok; Terai, Motoaki; Deng, Zigang; Zheng, Jun; Wang, Jiasu; Umemoto, Katsuya; Du, Jia; Febvre, Pascal; Keenan, Shane; Mukhanov, Oleg; Cooley, Lance D.; Foley, Cathy P.; Hassenzahl, William V.; Izumi, Mitsuru

2013-11-01

There is universal agreement between the United Nations and governments from the richest to the poorest nations that humanity faces unprecedented global challenges relating to sustainable energy, clean water, low-emission transportation, coping with climate change and natural disasters, and reclaiming use of land. We have invited researchers from a range of eclectic research areas to provide a Roadmap of how superconducting technologies could address these major challenges confronting humanity. Superconductivity has, over the century since its discovery by Kamerlingh Onnes in 1911, promised to provide solutions to many challenges. So far, most superconducting technologies are esoteric systems that are used in laboratories and hospitals. Large science projects have long appreciated the ability of superconductivity to efficiently create high magnetic fields that are otherwise very costly to achieve with ordinary materials. The most successful applications outside of large science are high-field magnets for magnetic resonance imaging, laboratory magnetometers for mineral and materials characterization, filters for mobile communications, and magnetoencephalography for understanding the human brain. The stage is now set for superconductivity to make more general contributions. Humanity uses practically unthinkable amounts of energy to drive our modern way of life. Overall, global power usage has been predicted to almost double from 16.5 to 30 TW in the next four decades (2011 Equinox Summit: Energy 2030 http://wgsi.org/publications-resources). The economy with which electrons carry energy compels the continued quest for efficient superconducting power generation, energy storage, and power transmission. The growing global population requires new arable land and treatment of water, especially in remote areas, and superconductivity offers unique solutions to these problems. Exquisite detectors give warning of changes that are otherwise invisible. Prediction of climate and disasters will be helped by future supercomputer technologies that support huge amounts of data and sophisticated modeling, and with the aid of superconductivity these systems might not require the energy of a large city. We present different sections on applications that could address (or are addressing) a range of environmental issues. The Roadmap covers water purification, power distribution and storage, low-environmental impact transport, environmental sensing (particularly for the removal of unexploded munitions), monitoring the Earth’s magnetic fields for earthquakes and major solar activity, and, finally, developing a petaflop supercomputer that only requires 3% of the current supercomputer power provision while being 50 times faster. Access to fresh water. With only 2.5% of the water on Earth being fresh and climate change modeling forecasting that many areas will become drier, the ability to recycle water and achieve compact water recycling systems for sewage or ground water treatment is critical. The first section (by Nishijima) points to the potential of superconducting magnetic separation to enable water recycling and reuse. Energy. The Equinox Summit held in Waterloo Canada 2011 (2011 Equinox Summit: Energy 2030 http://wgsi.org/publications-resources) identified electricity use as humanity’s largest contributor to greenhouse gas emissions. Our appetite for electricity is growing faster than for any other form of energy. The communiqué from the summit said ‘Transforming the ways we generate, distribute and store electricity is among the most pressing challenges facing society today…. If we want to stabilize CO2 levels in our atmosphere at 550 parts per million, all of that growth needs to be met by non-carbon forms of energy’ (2011 Equinox Summit: Energy 2030 http://wgsi.org/publications-resources). Superconducting technologies can provide the energy efficiencies to achieve, in the European Union alone, 33-65% of the required reduction in greenhouse gas emissions according to the Kyoto Protocol (Hartikainen et al 2003 Supercond. Sci. Technol. 16 963). New technologies would include superconducting energy storage systems to effectively store power generation from renewable sources as well as high-temperature superconducting systems used in generators, transformers and synchronous motors in power stations and heavy-industry facilities. However, to be effective, these systems must be superior to conventional systems and, in reality, market penetration will occur as existing electrical machinery is written off. At current write-off rates, to achieve a 50% transfer to superconducting systems will take 20 years (Hartikainen et al 2003 Supercond. Sci. Technol. 16 963). The Roadmap next considers dc transmission of green power with a section by Eckroad and Marian who provide an update on the development of superconducting power transmission lines in view of recent sustainability studies. The potential of magnetic energy storage is then presented by Coi and Kim, who argue that a successful transition to wind and solar power generation must be harmonized with the conventional electrical network, which requires a storage technology with a fast response and long backup times. Transport. Superconducting Maglev trains and motors for international shipping have the potential to considerably reduce the emissions that contribute to greenhouse gases while improving their economic viability by reducing losses and improving efficiencies. International shipping, alone, contributes 3% of the greenhouse gas emissions. Three sections of the Roadmap identify how high-speed rail can be a major solution to providing fast, low energy, environmentally-friendly transport enabling reduction in automobile and aircraft travel by offering an alternative that is very competitive. With maritime international environmental regulations tightening, HTS motors with the characteristics of high torque and compactness will become important devices for high-performance and low-emission electric ship propulsion systems. A section on the development of a megawatt-class superconducting motor for ship propulsion is presented by Umemoto. Monitoring in manufacturing for waste reduction. Environmental impact from the waste created by the manufacturing sector and the need to make manufacturing efficient can be addressed by terahertz imaging. This technology has great potential in non-destructive testing, industrial process monitoring and control to greatly improve the industry process efficiency and reliability by reducing waste materials and toxic by-products. The section by Du shows how terahertz imaging can provide process and property information such as rust levels under paint that can assist with the reduction of waste in manufacturing and maintenance. Monitoring for naturally occurring disturbances. The environmental and social impact of natural disasters is mounting. Febvre provides the Roadmap for the use of ultra-sensitive magnetometry to understand geomagnetic phenomena and Earth-ionosphere couplings through the study of very small variations of the magnetic field. This magnetic monitoring has many implications for understanding our environment and providing new tools for early warning of natural hazards, either on Earth or in space which will enable us to be better prepared for natural disasters. Restoring environments after military use. Throughout the world, there are many areas confirmed or suspected of being contaminated by unexploded munitions known as unexploded ordnance (UXO). Its presence is the result of wars and training of military forces. Areas affected by UXO contamination are hazardous to the public and have a major influence on the nature of land use. UXO has impact in developed as well as developing nations. For example, the USA has UXO dating back to the American Civil War and countries such as Cambodia are living with landmines as a daily issue due to more recent wars. Underwater UXO has caused severe impacts such as the explosion in 1969 in the waters of Kent in the UK that caused a reading of 4.5 on the Richter scale for earthquake monitors. Another example was a land-based detonation of a 500 kg World War II bomb in Germany killing three people in 2010. There is countless UXO from recent conflicts worldwide. Detection and accurate location with 100% reliability is required to return land to safe civilian use. Keenan provides details of a prototype magnetic gradiometer developed for this purpose. Reducing power needs for high-end IT. Supercomputers are so large that they are close to requiring their own small power plant to support the energy needed to run the computer. For example, in 2011 Facebook data centers and operations used 532 million kW hours of energy. Mukhanov explores the potential of reducing the power dissipation for future supercomputers from more than 500 MW for Exascale systems to 0.2 MW by using superconducting-ferromagnetic Josephson junctions for magnetic memory and programmable logic. Clearly superconductivity is an ultimate energy-saving technology, and its practical implementation will contribute to the reduction of CO2 emissions, improved water purification, reduction of waste and timely preparedness for natural disasters or significant events. This Roadmap shows how the application of superconducting technologies will have a significant impact when they are adopted.

Hybrid Arrays for Chemical Sensing

NASA Astrophysics Data System (ADS)

Kramer, Kirsten E.; Rose-Pehrsson, Susan L.; Johnson, Kevin J.; Minor, Christian P.

In recent years, multisensory approaches to environment monitoring for chemical detection as well as other forms of situational awareness have become increasingly popular. A hybrid sensor is a multimodal system that incorporates several sensing elements and thus produces data that are multivariate in nature and may be significantly increased in complexity compared to data provided by single-sensor systems. Though a hybrid sensor is itself an array, hybrid sensors are often organized into more complex sensing systems through an assortment of network topologies. Part of the reason for the shift to hybrid sensors is due to advancements in sensor technology and computational power available for processing larger amounts of data. There is also ample evidence to support the claim that a multivariate analytical approach is generally superior to univariate measurements because it provides additional redundant and complementary information (Hall, D. L.; Linas, J., Eds., Handbook of Multisensor Data Fusion, CRC, Boca Raton, FL, 2001). However, the benefits of a multisensory approach are not automatically achieved. Interpretation of data from hybrid arrays of sensors requires the analyst to develop an application-specific methodology to optimally fuse the disparate sources of data generated by the hybrid array into useful information characterizing the sample or environment being observed. Consequently, multivariate data analysis techniques such as those employed in the field of chemometrics have become more important in analyzing sensor array data. Depending on the nature of the acquired data, a number of chemometric algorithms may prove useful in the analysis and interpretation of data from hybrid sensor arrays. It is important to note, however, that the challenges posed by the analysis of hybrid sensor array data are not unique to the field of chemical sensing. Applications in electrical and process engineering, remote sensing, medicine, and of course, artificial intelligence and robotics, all share the same essential data fusion challenges. The design of a hybrid sensor array should draw on this extended body of knowledge. In this chapter, various techniques for data preprocessing, feature extraction, feature selection, and modeling of sensor data will be introduced and illustrated with data fusion approaches that have been implemented in applications involving data from hybrid arrays. The example systems discussed in this chapter involve the development of prototype sensor networks for damage control event detection aboard US Navy vessels and the development of analysis algorithms to combine multiple sensing techniques for enhanced remote detection of unexploded ordnance (UXO) in both ground surveys and wide area assessments.

Spectral-Element Simulations of Wave Propagation in Porous Media: Finite-Frequency Sensitivity Kernels Based Upon Adjoint Methods

NASA Astrophysics Data System (ADS)

Morency, C.; Tromp, J.

2008-12-01

The mathematical formulation of wave propagation in porous media developed by Biot is based upon the principle of virtual work, ignoring processes at the microscopic level, and does not explicitly incorporate gradients in porosity. Based on recent studies focusing on averaging techniques, we derive the macroscopic porous medium equations from the microscale, with a particular emphasis on the effects of gradients in porosity. In doing so, we are able to naturally determine two key terms in the momentum equations and constitutive relationships, directly translating the coupling between the solid and fluid phases, namely a drag force and an interfacial strain tensor. In both terms, gradients in porosity arise. One remarkable result is that when we rewrite this set of equations in terms of the well known Biot variables us, w), terms involving gradients in porosity are naturally accommodated by gradients involving w, the fluid motion relative to the solid, and Biot's formulation is recovered, i.e., it remains valid in the presence of porosity gradients We have developed a numerical implementation of the Biot equations for two-dimensional problems based upon the spectral-element method (SEM) in the time domain. The SEM is a high-order variational method, which has the advantage of accommodating complex geometries like a finite-element method, while keeping the exponential convergence rate of (pseudo)spectral methods. As in the elastic and acoustic cases, poroelastic wave propagation based upon the SEM involves a diagonal mass matrix, which leads to explicit time integration schemes that are well-suited to simulations on parallel computers. Effects associated with physical dispersion & attenuation and frequency-dependent viscous resistance are addressed by using a memory variable approach. Various benchmarks involving poroelastic wave propagation in the high- and low-frequency regimes, and acoustic-poroelastic and poroelastic-poroelastic discontinuities have been successfully performed. We present finite-frequency sensitivity kernels for wave propagation in porous media based upon adjoint methods. We first show that the adjoint equations in porous media are similar to the regular Biot equations upon defining an appropriate adjoint source. Then we present finite-frequency kernels for seismic phases in porous media (e.g., fast P, slow P, and S). These kernels illustrate the sensitivity of seismic observables to structural parameters and form the basis of tomographic inversions. Finally, we show an application of this imaging technique related to the detection of buried landmines and unexploded ordnance (UXO) in porous environments.

Ground-penetrating radar: use and misuse

NASA Astrophysics Data System (ADS)

Olhoeft, Gary R.

1999-10-01

Ground penetrating radar (GPR) has been used to explore the subsurface of the earth since 1929. Over the past 70 years, it has been widely used, misused and abused. Use includes agriculture, archaeology, environmental and geotechnical site characterization, minerals, groundwater and permafrost exploration, tunnel, utility, and unexploded ordnance location, dam inspection, and much more. Misuse includes mistaking above ground reflections for subsurface events or mapping things from off to the side as if they were directly below, synthetic aperture processing of dispersive data, minimum phase deconvolution, locating objects smaller than resolution limits of the wavelength in the ground, ignoring Fresnel zone limitations in mapping subsurface structure, processing radar data through seismic software packages without allowing for the differences, mapping the bottom of metal pipes from the top, claiming to see through thousands of feet of sediments, and more. GPR is also being abused as the regulatory environment changes and the radiofrequency spectrum is becoming more crowded by cellular phones, pagers, garage door openers, wireless computer networks, and the like. It is often thought to be a source of interference (though it never is) and it is increasingly interfered with by other radiofrequency transmitters.

The assessment of the energetic compound 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-Hexaazaisowurtzitane (CL-20) degradability in soil.

PubMed

Strigul, Nikolay; Braida, Washington; Christodoulatos, Christos; Balas, Wendy; Nicolich, Steven

2006-01-01

CL-20 is a relatively new energetic compound with applications in explosive and propellant formulations. Currently, information about the fate of CL-20 in ecological systems is scarce. The aim of this study is to evaluate the biodegradability of CL-20 in soil environments. Four soils were used where initial CL-20 concentrations (above water solubility) ranged from 125 to 1500 mg of CL-20 per kg dry soil (corresponding to the concentrations derived from unexploded ordnance, low order detonation, or manufacturing spills). CL-20 appears to be biodegradable in soil under anaerobic conditions, and additions of organic substrates can substantially accelerate this process. However, CL-20 is not degraded in soil under aerobic conditions kept in the dark at temperatures up to 30 degrees C without organic amendments. Additions of starch or cellulose promote the biodegradation of CL-20 under aerobic conditions. Soil microbial community mediated biodegradation and plant uptake appears to enhance CL-20 biodegradation, the latter suggesting a possible route for CL-20 to entry in the food chain.

Geo-location Requirements for UXO Discrimination (Guidance Document)

DTIC Science & Technology

2008-05-01

Signatures Measured by MTADS," Proceedings of the UXO Forum, Anaheim, pp. 282-291, May 1998. [5] Billings, S., L. Pasion and D. Oldenburg, "UXO...February 2002. [6] Billings, S., L. Pasion and D. Oldenburg, "Inversion of Magnetics for UXO Discrimination and Identification," UXO/Countermine Forum...1286-1293, June 2001. [10] Pasion , L. and D. Oldenburg, "A Discrimination Algorithm for UXO Using Time Domain Electromagnetics," J. Environmental

Feasibility Study for an Autonomous UAV -Magnetometer System -- Final Report on SERDP SEED 1509:2206

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roelof Versteeg; Mark McKay; Matt Anderson

2007-09-01

Large areas across the United States are potentially contaminated with UXO, with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with 1) near 100 % coverage and 2) near 100 % detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area scanning is a multi-level one, in which medium altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry followed by surface investigations using either towed geophysicalmore » sensor arrays or man portable sensors. In order to be effective for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 – 3 meters. These altitude requirements means that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys (resulting in costs of approximately $100-$150/acre). Surface towed arrays provide high resolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. Thus, other systems are needed allowing for effective data collection. An UAV (Unmanned Aerial Vehicle) magnetometer platform is an obvious alternative. The motivation behind such a system is that it would be safer for the operators, cheaper in initial and O&M costs, and more effective in terms of site characterization. However, while UAV data acquisition from fixed wing platforms for large (> 200 feet) stand off distances is relatively straight forward, a host of challenges exist for low stand-off distance (~ 6 feet) UAV geophysical data acquisition. The objective of SERDP SEED 1509:2006 was to identify the primary challenges associated with a low stand off distance autonomous UAV magnetometer platform and to investigate whether these challenges can be resolved successfully such that a successful UAV magnetometer platform can be constructed. The primary challenges which were identified and investigated include: 1. The feasibility of assembling a payload package which integrates magnetometers, accurate positioning systems (DGPS, height above ground measurement), obstacle avoidance systems, power infrastructure, communications and data storage as well as auxiliary flight controls 2. The availability of commercial UAV platforms with autonomous flight capability which can accommodate this payload package 3. The feasibility of integrating obstacle avoidance controls in UAV platform control 4. The feasibility of collecting high quality magnetic data in the vicinity of an UAV.« less

Principles and status of neutron-based inspection technologies

NASA Astrophysics Data System (ADS)

Gozani, Tsahi

2011-06-01

Nuclear based explosive inspection techniques can detect a wide range of substances of importance for a wide range of objectives. For national and international security it is mainly the detection of nuclear materials, explosives and narcotic threats. For Customs Services it is also cargo characterization for shipment control and customs duties. For the military and other law enforcement agencies it could be the detection and/or validation of the presence of explosive mines, improvised explosive devices (IED) and unexploded ordnances (UXO). The inspection is generally based on the nuclear interactions of the neutrons (or high energy photons) with the various nuclides present and the detection of resultant characteristic emissions. These can be discrete gamma lines resulting from the thermal neutron capture process (n,γ) or inelastic neutron scattering (n,n'γ) occurring with fast neutrons. The two types of reactions are generally complementary. The capture process provides energetic and highly penetrating gamma rays in most inorganic substances and in hydrogen, while fast neutron inelastic scattering provides relatively strong gamma-ray signatures in light elements such as carbon and oxygen. In some specific important cases unique signatures are provided by the neutron capture process in light elements such as nitrogen, where unusually high-energy gamma ray is produced. This forms the basis for key explosive detection techniques. In some cases the elastically scattered source (of mono-energetic) neutrons may provide information on the atomic weight of the scattering elements. The detection of nuclear materials, both fissionable (e.g., 238U) and fissile (e.g., 235U), are generally based on the fissions induced by the probing neutrons (or photons) and detecting one or more of the unique signatures of the fission process. These include prompt and delayed neutrons and gamma rays. These signatures are not discrete in energy (typically they are continua) but temporally and energetically significantly different from the background, thus making them readily distinguishable. The penetrability of neutrons as probes and signatures as well as the gamma ray signatures make neutron interrogation applicable to the inspection of large conveyances such as cars, trucks, marine containers and also smaller objects like explosive mines concealed in the ground. The application of nuclear interrogation techniques greatly depends on operational requirements. For example explosive mines and IED detection clearly require one-sided inspection, which excludes transmission based inspection (e.g., transmission radiography) and greatly limits others. The technologies developed over the last decades are now being implemented with good results. Further advances have been made over the last several years that increase the sensitivity, applicability and robustness of these systems. The principle, applications and status of neutron-based inspection techniques will be reviewed.

Method and apparatus for optimized sampling of volatilizable target substances

DOEpatents

Lindgren, Eric R.; Phelan, James M.

2004-10-12

An apparatus for capturing, from gases such as soil gas, target analytes. Target analytes may include emanations from explosive materials or from residues of explosive materials. The apparatus employs principles of sorption common to solid phase microextraction, and is best used in conjunction with analysis means such as a gas chromatograph. To sorb target analytes, the apparatus functions using various sorptive structures to capture target analyte. Depending upon the embodiment, those structures may include a capillary tube including an interior surface on which sorptive material (similar to that on the surface of a SPME fiber) is supported (along with means for moving gases through the capillary tube so that the gases come into close proximity to the sorptive material). In one disclosed embodiment, at least one such sorptive structure is associated with an enclosure including an opening in communication with the surface of a soil region potentially contaminated with buried explosive material such as unexploded ordnance. Emanations from explosive materials can pass into and accumulate in the enclosure where they are sorbed by the sorptive structures. Also disclosed is the use of heating means such as microwave horns to drive target analytes into the soil gas from solid and liquid phase components of the soil.

Spectroscopic signatures of PETN in contact with sand particles

NASA Astrophysics Data System (ADS)

Ballesteros, Luz M.; Herrera, Gloria M.; Castro, Miguel E.; Briano, Julio; Mina, Nairmen; Hernandez-Rivera, Samuel P.

2005-06-01

The detection of explosive materials is not only important as an issue in landmines but also for global security reasons, unexploded ordnance, and Improvised Explosive Devices detection. In such areas, explosives detection has played a central role in ensuring the safety of the lives of citizens in many countries. Raman Spectroscopy is a well established tool for vibrational spectroscopic analysis and can be applied to the field of explosives identification and detection. The analysis of PETN is important because it is used in laminar form or mixed with RDX to manufacture Semtex plastic explosive and in the fabrication of Improvised Explosive Devices (IEDs). Our investigation is focused on the study of spectroscopic signatures of PETN in contact with soil. Ottawa sand mixed in different proportions with PETN together with the study of the influence of pH, temperature, humidity, and UV light on the vibrational signatures of the mixtures constitute the core of the investigation. The results reveal that the characteristic bands of PETN are not significantly shifted but rather appear constant with respect of the ubiquitous band of sand (~463 cm-1). These results will make possible the development of highly sensitive sensors for detection of explosives materials and IDEs.

Multi-Temporal Analysis of WWII Reconnaissance Photos

NASA Astrophysics Data System (ADS)

Meixner, P.; Eckstein, M.

2016-06-01

There are millions of aerial photographs from the period of the Second Wold War available in the Allied archives, obtained by aerial photo reconnaissance, covering most of today's European countries. They are spanning the time from 1938 until the end of the war and even beyond. Photo reconnaissance provided intelligence information for the Allied headquarters and accompanied the bombing offensive against the German homeland and the occupied territories. One of the initial principal targets in Bohemia were the synthetized fuel works STW AG (Sudetenländische Treibstoffwerke AG) in Zaluzi (formerly Maltheuren) near Most (formerly Brück), Czech Republic. The STW AG synthetized fuel plant was not only subject to bombing raids, but a subject to quite intensive photo reconnaissance, too - long before the start of the bombing campaign. With a multi-temporal analysis of the available imagery from international archives we will demonstrate the factory build-up during 1942 and 1943, the effects of the bombing raids in 1944 and the struggle to keep the plant working in the last year of the war. Furthermore we would like to show the impact the bombings have today, in form of potential unexploded ordnance in the adjacent area of the open cast mines.

Mobile TNA system to detect explosives and drugs concealed in cars and trucks

NASA Astrophysics Data System (ADS)

Bendahan, Joseph; Gozani, Tsahi

1998-12-01

The drug problem in the U.S. is serious and efforts to fight it are constrained by the lack of adequate means to curb the inflow of smuggled narcotics into the country through cargo containers. Also, events such as the disastrous explosion in Oklahoma City, the IRA bombing in London, and the bombing of the U.S. military residence in Dharan make the development of new tools for the detection of explosives and drugs in vehicles imperative. Thermal neutron analysis (TNA) technology, developed for the detection of explosives in suitcases, and detection of landmines and unexploded ordnance is presently being applied to the nonintrusive detection of significant amounts of explosives and drugs concealed in cars, trucks and large cargo containers. TNA technology is based on the analysis of characteristic gamma rays emitted following thermal neutron capture. A TNA system can be used in a variety of operational scenarios, such as inspection before an unloaded cargo container from a spit is moved to temporary storage, inspection of trucks unloaded from a ferry, or inspection of vehicles parked close to Federal building or military bases. This paper will discuss the detection process and operational scenarios, and will present results from recent simulations and measurements.

Analysis of Landmine Fatalities and Injuries in the Kurdistan Region.

PubMed

Heshmati, Almas; Khayyat, Nabaz T

2015-09-01

This study analyzes landmine victim data in the Kurdistan Region during the period 1960 to 2005. A regression analysis is used to identify the determinants and impact of the probability of getting killed by mines and unexploded ordnances. The rates of killed/injured victims are explained using a set of socioeconomic variables. As the data are a repeated cross-section in which the individuals are observed when they are subjected to landmine incidents, and to account for the dynamic aspect of the process and heterogeneity by location as well as to control for unobserved location and time effects, a pseudo panel data are created where districts are observed over the entire time period forming a panel data. The results show that (a) males, children, and the elderly are more susceptible to a higher level of landmine risks; (b) landmine training and awareness programs do not reduce the rate of landmine mortality; and (c) the rate of incidents are declining over time. This result can be used in the planning, monitoring, and resource allocation for mine action, as well as labor market programs and rehabilitation activities. © The Author(s) 2014.

Information surfing with the JHU/APL coherent imager

NASA Astrophysics Data System (ADS)

Ratto, Christopher R.; Shipley, Kara R.; Beagley, Nathaniel; Wolfe, Kevin C.

2015-05-01

The ability to perform remote forensics in situ is an important application of autonomous undersea vehicles (AUVs). Forensics objectives may include remediation of mines and/or unexploded ordnance, as well as monitoring of seafloor infrastructure. At JHU/APL, digital holography is being explored for the potential application to underwater imaging and integration with an AUV. In previous work, a feature-based approach was developed for processing the holographic imagery and performing object recognition. In this work, the results of the image processing method were incorporated into a Bayesian framework for autonomous path planning referred to as information surfing. The framework was derived assuming that the location of the object of interest is known a priori, but the type of object and its pose are unknown. The path-planning algorithm adaptively modifies the trajectory of the sensing platform based on historical performance of object and pose classification. The algorithm is called information surfing because the direction of motion is governed by the local information gradient. Simulation experiments were carried out using holographic imagery collected from submerged objects. The autonomous sensing algorithm was compared to a deterministic sensing CONOPS, and demonstrated improved accuracy and faster convergence in several cases.

Military applications and examples of near-surface seismic surface wave methods (Invited)

NASA Astrophysics Data System (ADS)

sloan, S.; Stevens, R.

2013-12-01

Although not always widely known or publicized, the military uses a variety of geophysical methods for a wide range of applications--some that are already common practice in the industry while others are truly novel. Some of those applications include unexploded ordnance detection, general site characterization, anomaly detection, countering improvised explosive devices (IEDs), and security monitoring, to name a few. Techniques used may include, but are not limited to, ground penetrating radar, seismic, electrical, gravity, and electromagnetic methods. Seismic methods employed include surface wave analysis, refraction tomography, and high-resolution reflection methods. Although the military employs geophysical methods, that does not necessarily mean that those methods enable or support combat operations--often times they are being used for humanitarian applications within the military's area of operations to support local populations. The work presented here will focus on the applied use of seismic surface wave methods, including multichannel analysis of surface waves (MASW) and backscattered surface waves, often in conjunction with other methods such as refraction tomography or body-wave diffraction analysis. Multiple field examples will be shown, including explosives testing, tunnel detection, pre-construction site characterization, and cavity detection.

Numerical modeling of magnetic moments for UXO applications

USGS Publications Warehouse

Sanchez, V.; Li, Y.; Nabighian, M.; Wright, D.

2006-01-01

The surface magnetic anomaly observed in UXO clearance is mainly dipolar and, consequently, the dipole is the only magnetic moment regularly recovered in UXO applications. The dipole moment contains information about intensity of magnetization but lacks information about shape. In contrast, higher-order moments, such as quadrupole and octupole, encode asymmetry properties of the magnetization distribution within the buried targets. In order to improve our understanding of magnetization distribution within UXO and non-UXO objects and its potential utility in UXO clearance, we present a 3D numerical modeling study for highly susceptible metallic objects. The basis for the modeling is the solution of a nonlinear integral equation describing magnetization within isolated objects. A solution for magnetization distribution then allows us to compute magnetic moments of the object, analyze their relationships, and provide a depiction of the surface anomaly produced by different moments within the object. Our modeling results show significant high-order moments for more asymmetric objects situated at depths typical of UXO burial, and suggest that the increased relative contribution to magnetic gradient data from these higher-order moments may provide a practical tool for improved UXO discrimination.

Relative importance of magnetic moments in UXO clearance applications

USGS Publications Warehouse

Sanchez, V.; Li, Y.; Nabighian, M.; Wright, D.

2006-01-01

Surface magnetic anomaly observed in UXO clearance is mainly dipolar and, as a result, the dipole is the only moment used regularly in UXO applications. The dipole moment contains intensity of magnetization information but lacks shape information. Unlike dipole, higher-order moments, such as quadrupole and octupole, encode asymmetry properties of magnetization distribution within buried targets. In order to improve our understanding of magnetization distribution within UXO and non-UXO objects and its potential utility in UXO clearance, we present results of a 3D numerical modeling study for highly susceptible metallic objects. The basis for modeling is the solution of a nonlinear integral equation, describing magnetization within isolated objects, allowing us to compute magnetic moments of the object, analyze their relationships, and provide a depiction of the surface anomaly produced by the different moments within the object. Our modeling results show significant high-order moments for more asymmetric objects situated at typical UXO burial depths, and suggest that the increased relative contribution to magnetic gradient data from these higher-order moments may provide a practical tool for improved UXO discrimination. ?? 2005 Society of Exploration Geophysicists.

Seismic Imaging of UXO-Contaminated Underwater Sites (Interim Report)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gritto, Roland; Korneev, Valeri; Nihei, Kurt

2004-11-30

Finite difference modeling with 2-dimensional models were conducted to evaluate the performance of source-receiver arrays to locate UXO in littoral environments. The model parameters were taken from measurements in coastal areas with typical bay mud and from examples in the literature. Seismic arrays are well suited to focus energy by steering the elements of the array to any point in the medium that acts as an energy source. This principle also applies to seismic waves that are backscattered by buried UXO. The power of the array is particularly evident in strong noise conditions when the signal-to-noise ratio is too lowmore » to observe the scattered signal on the seismograms. Using a seismic array, it was possible to detect and locate the UXO with a reliability similar to noise free situations. When the UXO was positioned within 3-6 wavelengths of the incident signal from the source array, the resolution was good enough to determine the dimensions of the UXO from the scattered waves. Beyond this distance this distinction decreased gradually while the location and the center of the UXO were still determined reliably. The location and the dimensions of two adjacent UXO were resolved down to a separation of 1/3 of the dominant wavelength of the incident wave, at which time interference effects began to appear. In the investigated cases, the ability to locate a UXO was independent on the use of a model with a rippled or a flat seafloor, as long as the array was located above the UXO. Nevertheless, the correct parameters of the seafloor interface were obtained in these cases. An investigation to find the correct migration velocity in the sediments to locate the UXO revealed that a range of velocity gradients centered around the correct velocity model produced comparable results, which needs to be further investigated with physical modeling.« less

Handheld Sensor for UXO Discrimination:

DTIC Science & Technology

2006-06-01

between buried UXO and clutter. This project demonstrated the use of commercially available technology (Geonics EM61-HH handheld metal detector ) for...determine whether each target was UXO or clutter. The Geonics EM61-HH handheld metal detector is a pulsed electromagnetic induction (EMI) sensor. The...processing, the EM61-HH handheld metal detector can 2 be used in a cued identification mode to reliably discriminate between buried UXO and clutter

Hand-Held EMI Sensor Combined with Inertial Positioning for Cued UXO Discrimination - APG Standardized UXO Test Site

DTIC Science & Technology

2013-04-01

Measurement Tracking System (SAINT) with an advanced hand-held, time-domain electromagnetic sensor (TEM-HH) and document classification performance at...rejecting 77% of the clutter. 15. SUBJECT TERMS EMI, electromagnetic induction, UXO classification, UXO, IMU, inertial measurement unit, 16. SECURITY...U c. THIS PAGE U UU 19b. TELEPHONE NUMBER (include area code) 919-677-1560 Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. Z39.18

GP Workbench Manual: Technical Manual, User's Guide, and Software Guide

USGS Publications Warehouse

Oden, Charles P.; Moulton, Craig W.

2006-01-01

GP Workbench is an open-source general-purpose geophysical data processing software package written primarily for ground penetrating radar (GPR) data. It also includes support for several USGS prototype electromagnetic instruments such as the VETEM and ALLTEM. The two main programs in the package are GP Workbench and GP Wave Utilities. GP Workbench has routines for filtering, gridding, and migrating GPR data; as well as an inversion routine for characterizing UXO (unexploded ordinance) using ALLTEM data. GP Workbench provides two-dimensional (section view) and three-dimensional (plan view or time slice view) processing for GPR data. GP Workbench can produce high-quality graphics for reports when Surfer 8 or higher (Golden Software) is installed. GP Wave Utilities provides a wide range of processing algorithms for single waveforms, such as filtering, correlation, deconvolution, and calculating GPR waveforms. GP Wave Utilities is used primarily for calibrating radar systems and processing individual traces. Both programs also contain research features related to the calibration of GPR systems and calculating subsurface waveforms. The software is written to run on the Windows operating systems. GP Workbench can import GPR data file formats used by major commercial instrument manufacturers including Sensors and Software, GSSI, and Mala. The GP Workbench native file format is SU (Seismic Unix), and subsequently, files generated by GP Workbench can be read by Seismic Unix as well as many other data processing packages.

Development of autonomous magnetometer rotorcraft for wide area assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roelof Versteeg; Matt Anderson; Les Beard

2010-04-01

Large areas across the United States are potentially contaminated with UXO, with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with 1) near 100 % coverage and 2) near 100 % detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area assessment is a multi-level one, in which medium - altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry. Subsequent to this wide area assessment targetedmore » surface investigations are performed using either towed geophysical sensor arrays or man portable sensors. In order to be an effective tool for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 – 3 meters. These altitude requirements mean that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys (resulting in costs of approximately $100-$150/acre). In addition, due to the low altitude there are substantial risks to pilots and equipment. Surface towed arrays provide high resolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. There is thus a need for other systems which can be used for effective data collection. An UAV (Unmanned Aerial Vehicle) magnetometer platform is an obvious alternative. The motivation behind such a system is that it reduces risk to operators, is lower in initial and Operational and Maintenance (O&M) costs (and can thus potentially be applied to smaller sites) and has the potential of being more effective in terms of detection and possibly characterization (through the use of dynamic acquisition, i.e. survey mission inflight reprioritization). We describe and report on a one year effort with as primary goal to provide a recommendation to SERDP for a path forward in the implementation of one or more autonomous unmanned magnetometer rotorcraft platforms. This recommendation (which is provided in chapter 6) is based on the following three elements a) An assessment on the applicability of autonomous rotorcraft magnetometer systems to the current DoD site inventory, and an initial assessment of which type(s) of autonomous unmanned magnetometer rotorcraft platforms (in terms of performance characteristics such as payload, altitude, obstacle avoidance, production rate and flight time) would be most relevant to this inventory (chapter 3); b) An evaluation of the feasibility of assembling such platforms from commercial components (unmanned rotorcraft, control systems and sensors – both magnetometer sensors and supporting sensors). This evaluation included several highly successful field tests (chapter 4 and 5); c) A recommendation of the path forward, which includes a detailed outline of the efforts required in the design, assembly and testing of different modular platforms (chapter 6)« less

UXO Characterization in Challenging Survey Environments Using the MPV

DTIC Science & Technology

2017-03-01

DEMONSTRATION REPORT Demonstration of the MPV at a Residential Area in Puako, Hawaii: UXO Characterization in Challenging Survey ...DATES COVERED (From - To) 4. TITLE AND SUBTITLE UXO Characterization in Challenging Survey Environments Using the MPV 5a...19 5.4.1 Detection survey

Real-time acquisition and preprocessing system of transient electromagnetic data based on LabVIEW

NASA Astrophysics Data System (ADS)

Zhao, Huinan; Zhang, Shuang; Gu, Lingjia; Sun, Jian

2014-09-01

Transient electromagnetic method (TEM) is regarded as an everlasting issue for geological exploration. It is widely used in many research fields, such as mineral exploration, hydrogeology survey, engineering exploration and unexploded ordnance detection. The traditional measurement systems are often based on ARM DSP or FPGA, which have not real-time display, data preprocessing and data playback functions. In order to overcome the defects, a real-time data acquisition and preprocessing system based on LabVIEW virtual instrument development platform is proposed in the paper, moreover, a calibration model is established for TEM system based on a conductivity loop. The test results demonstrated that the system can complete real-time data acquisition and system calibration. For Transmit-Loop-Receive (TLR) response, the correlation coefficient between the measured results and the calculated results is 0.987. The measured results are basically consistent with the calculated results. Through the late inversion process for TLR, the signal of underground conductor was obtained. In the complex test environment, abnormal values usually exist in the measured data. In order to solve this problem, the judgment and revision algorithm of abnormal values is proposed in the paper. The test results proved that the proposed algorithm can effectively eliminate serious disturbance signals from the measured transient electromagnetic data.

Concepts and procedures required for successful reduction of tensor magnetic gradiometer data obtained from an unexploded ordnance detection demonstration at Yuma Proving Grounds, Arizona

USGS Publications Warehouse

Bracken, Robert E.; Brown, Philip J.

2006-01-01

On March 12, 2003, data were gathered at Yuma Proving Grounds, in Arizona, using a Tensor Magnetic Gradiometer System (TMGS). This report shows how these data were processed and explains concepts required for successful TMGS data reduction. Important concepts discussed include extreme attitudinal sensitivity of vector measurements, low attitudinal sensitivity of gradient measurements, leakage of the common-mode field into gradient measurements, consequences of thermal drift, and effects of field curvature. Spatial-data collection procedures and a spin-calibration method are addressed. Discussions of data-reduction procedures include tracking of axial data by mathematically matching transfer functions among the axes, derivation and application of calibration coefficients, calculation of sensor-pair gradients, thermal-drift corrections, and gradient collocation. For presentation, the magnetic tensor at each data station is converted to a scalar quantity, the I2 tensor invariant, which is easily found by calculating the determinant of the tensor. At important processing junctures, the determinants for all stations in the mapped area are shown in shaded relief map-view. Final processed results are compared to a mathematical model to show the validity of the assumptions made during processing and the reasonableness of the ultimate answer obtained.

New methods for interpretation of magnetic vector and gradient tensor data I: eigenvector analysis and the normalised source strength

NASA Astrophysics Data System (ADS)

Clark, David A.

2012-09-01

Acquisition of magnetic gradient tensor data is likely to become routine in the near future. New methods for inverting gradient tensor surveys to obtain source parameters have been developed for several elementary, but useful, models. These include point dipole (sphere), vertical line of dipoles (narrow vertical pipe), line of dipoles (horizontal cylinder), thin dipping sheet, and contact models. A key simplification is the use of eigenvalues and associated eigenvectors of the tensor. The normalised source strength (NSS), calculated from the eigenvalues, is a particularly useful rotational invariant that peaks directly over 3D compact sources, 2D compact sources, thin sheets and contacts, and is independent of magnetisation direction. In combination the NSS and its vector gradient determine source locations uniquely. NSS analysis can be extended to other useful models, such as vertical pipes, by calculating eigenvalues of the vertical derivative of the gradient tensor. Inversion based on the vector gradient of the NSS over the Tallawang magnetite deposit obtained good agreement between the inferred geometry of the tabular magnetite skarn body and drill hole intersections. Besides the geological applications, the algorithms for the dipole model are readily applicable to the detection, location and characterisation (DLC) of magnetic objects, such as naval mines, unexploded ordnance, shipwrecks, archaeological artefacts, and buried drums.

Single-Command Approach and Instrument Placement by a Robot on a Target

NASA Technical Reports Server (NTRS)

Huntsberger, Terrance; Cheng, Yang

2005-01-01

AUTOAPPROACH is a computer program that enables a mobile robot to approach a target autonomously, starting from a distance of as much as 10 m, in response to a single command. AUTOAPPROACH is used in conjunction with (1) software that analyzes images acquired by stereoscopic cameras aboard the robot and (2) navigation and path-planning software that utilizes odometer readings along with the output of the image-analysis software. Intended originally for application to an instrumented, wheeled robot (rover) in scientific exploration of Mars, AUTOAPPROACH could be adapted to terrestrial applications, notably including the robotic removal of land mines and other unexploded ordnance. A human operator generates the approach command by selecting the target in images acquired by the robot cameras. The approach path consists of multiple legs. Feature points are derived from images that contain the target and are thereafter tracked to correct odometric errors and iteratively refine estimates of the position and orientation of the robot relative to the target on successive legs. The approach is terminated when the robot attains the position and orientation required for placing a scientific instrument at the target. The workspace of the robot arm is then autonomously checked for self/terrain collisions prior to the deployment of the scientific instrument onto the target.

Quantification of Hydrodynamic Forcing on Smart Munitions on the Beach Face - Designof Smart Munitions

NASA Astrophysics Data System (ADS)

Cristaudo, D.; Bruder, B. L.; Puleo, J. A.

2016-12-01

Millions of unexploded ordnance (munitions) are located in the waters off of US coasts. They canmigrate to the beach and become a peril to local beach users. The research objective is to quantifythe small scale processes on the beach face responsible for munition mobility. Several experimentsat different sites with different wave and bathymetry conditions will be conducted. Realisticsurrogate munitions were constructed to facilitate the future experiments. Six different munitiontypes were replicated, selecting a range of calibers covering a variety of dimensions from 20 mmto 155 mm. The surrogates are made "smart" by designing them to house several internal sensors(the quantity depends on the available space inside the surrogate itself) that will aid in estimatingthe characteristics of their mobility. Each smart surrogate replicates the mass, center of gravity,and moment of inertia of the actual munition as close as possible. The sensors used inside the smartsurrogate munitions include: inertial motion units (IMU) to derive the surrogate position; Ubisenseultra-wideband tags for positioning in dry conditions; a Slamstick shock sensor to quantify thewave impact force on the surrogate; photocells to detect rolling and burial; and a pressure sensorto measure the water depth. The procedure of designing the smart surrogate munitions and sensorcapabilities will be presented.

Standardized Analysis for UXO Demonstration Sites

DTIC Science & Technology

2008-04-01

is a time-domain electromagnetic instrument designed to detect shallow ferrous and nonferrous metallic objects. The applicability of the EM61 for UXO...or spots show EMI field anomalies caused by buried metal objects, both UXO and clutter. Anomaly maps for APG are shown in Figure 5. The Blind Grid

Pedemis: A Portable Electromagnetic Induction Sensor with Integrated Positioning

DTIC Science & Technology

2012-04-27

International Society for Optical Engineering 5794(Part I), 346 – 357 (2005). [18] Pasion , L. R., “A unified approach to uxo discrimination using the...B., and O’Neill, K., “Camp butner uxo data inversion and classification using advanced emi models,” (2010). SERDP-MR-1572. [27] Pasion , L., “Uxo

Remote Excavation of Heavily Contaminated UXO Sites

DTIC Science & Technology

2007-12-01

detonation RF radio frequency RPM revolutions per minute Shaw Shaw Environmental Services SUXOS senior UXO supervisor Timberline Timberline ... Timberline Environmental Services, Inc. ( Timberline ). Timberline , and most notably Mr. Terry Northcutt, was the heart and soul of this project...the prime contractor responsible for project management and UXO support; and Timberline Environmental Services, 2 Inc. ( Timberline ) is responsible

UXO Forum 1996

DTIC Science & Technology

1996-01-01

Materiel (PM NSCM) Western Governors’ Association (WGA) 20070430075 March 26 - 28, 1996 Williamsburg, Virginia Distribution unlimited, Copy approved...for Public release UXO FORUM 1996 Conference Proceedings Williamsburg, Virginia March 26 - 28, 1996 DISTRIBUTION UNLIMITED per Marty Stutz zin April...2007 Best Available Copy DEPARTMENT OF DEFENSE EXPLOSIVES SAFETY BOARD 2461 EISENHOWER AVENUE ALEXANDRIA, VIRGINIA 22331-0600 5 UXO FORUM 1996

Hazards of Electromagnetic Radiation to Ordnance (HERO) Safety Test

DTIC Science & Technology

2013-01-10

Ordnance Test Procedure (JOTP)-061 Hazards of Electromagnetic Radiation to...DEPARTMENT OF DEFENSE JOINT ORDNANCE TEST PROCEDURE (JOTP)-061 HAZARDS OF ELECTROMAGNETIC RADIATION TO ORDNANCE (HERO) SAFETY...TEST Joint Services Munition Safety Test Working Group Joint Ordnance Test Procedure (JOTP)-061 Hazards of Electromagnetic Radiation

Discrimination Report ESTCP Project #MM-0437

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, Erika

2008-10-01

The FY06 Defense Appropriation contains funding for the 'Development of Advanced, Sophisticated, and Discrimination Technologies for UXO Cleanup' in the Environmental Security Technology Certification Program. In 2003, the Defense Science Board observed: 'The...problem is that instruments that can detect the buried UXOs also detect numerous scrap metal objects and other artifacts, which leads to an enormous amount of expensive digging. Typically 100 holes may be dug before a real UXO is unearthed. The Task Force assessment is that much of this wasteful digging can be eliminated by the use of more advanced technology instruments that exploit modern digital processing andmore » advanced multi-mode sensors to achieve an improved level of discrimination of scrap from UXOs'. Significant progress has been made in discrimination technology. To date, testing of these approaches has been primarily limited to test sites with only limited application at live sites. Acceptance of discrimination technologies requires demonstration of system capabilities at UXO sites under real world conditions. FE Warren Air Force Base (AFB) in Cheyenne, WY is one such site. The demonstration objective was to determine the discrimination capabilities, cost and reliability of the Berkeley UXO Discriminator (BUD) in discrimination of UXO from scrap metal in real life conditions. Lawrence Berkeley National Laboratory performed a detection and discrimination survey of the Priority 1 area ({approx}5 acres) of the FE Warren AFB. The data included a system characterization with the emplaced calibration items and targets in the Geophysical Prove Out (GPO) area.« less

Demonstration of the MPV at a Residential Area in Puako, Hawaii: UXO Characterization in Challenging Survey Environments Using the MPV

DTIC Science & Technology

2017-03-01

DEMONSTRATION REPORT Demonstration of the MPV at a Residential Area in Puako, Hawaii: UXO Characterization in Challenging Survey ...DATES COVERED (From - To) 09/2012-04/2017 4. TITLE AND SUBTITLE UXO Characterization in Challenging Survey Environments Using the MPV 5a. CONTRACT...19 5.4.1 Detection survey ..................................................................................................... 19 5.4.2 Cued

Final Report: Resolving and Discriminating Overlapping Anomalies from Multiple Objects in Cluttered Environments

DTIC Science & Technology

2015-12-15

UXO community . NAME Total Number: PERCENT_SUPPORTEDNAME FTE Equivalent: Total Number: Irma Shamatava 0.50 0.50 1 Resolving and Discriminating...Distinguishing an object of interest from innocuous items is the main problem that the UXO community is facing currently. This inverse problem...innocuous items is the main problem that the UXO community is facing currently. This inverse problem demands fast and accurate representation of

The UXO Classification Demonstration at the Former Camp Butner, NC

DTIC Science & Technology

2011-07-01

Symposium and Workshop, Technical Session 2D: Classification Methods for Military Munitions Response. 1 December 2010. [49] Pasion , L. Personal...Communication. 15 June 2011. [50] Pasion , L. “Practical Strategies for UXO Discrimination: Camp Butner Analysis.” ESTCP Munitions Management In-Progress...Review. 9 February 2011. [51] Pasion , L., et al. “UXO Discrimination Using Full Coverage and Cued Interrogation Data Sets at Camp Butner, NC.” Partners

Man-Portable Vector (MPV) EMI Sensor for UXO Contamination Assessment at Former Spencer Artillery Range, Tennessee

DTIC Science & Technology

2013-04-16

instantaneous polarization model ( Pasion and Oldenburg, 2001). The target polarizability decay parameters are the main features for the ensuing...Bell, T., Geo-location Requirements for UXO Discrimination. SERDP Geo-location Workshop, 2005. Billings, S., Pasion , L., Lhomme, N. and Oldenburg...Report. ESTCP Project MR-201005, 2011b. Pasion , L. & Oldenburg, D., A Discrimination Algorithm for UXO Using Time Domain Electromagnetics. Journal of

Discrimination Report: ESTCP UXO Discrimination Study, ESTCPProject #MM-0437

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, Erika; Smith, J. Torquil; Morrison, H. Frank

2007-12-21

The FY06 Defense Appropriation contains funding for the 'Development of Advanced, Sophisticated, Discrimination Technologies for UXO Cleanup' in the Environmental Security Technology Certification Program. In 2003, the Defense Science Board observed: 'The problem is that instruments that can detect the buried UXOs also detect numerous scrap metal objects and other artifacts, which leads to an enormous amount of expensive digging. Typically 100 holes may be dug before a real UXO is unearthed! The Task Force assessment is that much of this wasteful digging can be eliminated by the use of more advanced technology instruments that exploit modern digital processing andmore » advanced multi-mode sensors to achieve an improved level of discrimination of scrap from UXOs.' Significant progress has been made in discrimination technology. To date, testing of these approaches has been primarily limited to test sites with only limited application at live sites. Acceptance of discrimination technologies requires demonstration of system capabilities at real UXO sites under real world conditions. Any attempt to declare detected anomalies to be harmless and requiring no further investigation require demonstration to regulators of not only individual technologies, but of an entire decision making process. This discrimination study was be the first phase in what is expected to be a continuing effort that will span several years.« less

Data acquisition and analysis of the UNCOSS underwater explosive neutron sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carasco, Cedric; Eleon, Cyrille; Perot, Bertrand

2012-08-15

The purpose of the FP7 UNCOSS project (Underwater Coastal Sea Surveyor, http://www.uncoss-project.org) is to develop a neutron-based underwater explosive sensor to detect unexploded ordnance lying on the sea bottom. The Associated Particle Technique is used to focus the inspection on a suspicious object located by optical and electromagnetic sensors and to determine if there is an explosive charge inside. This paper presents the data acquisition electronics and data analysis software which have been developed for this project. A field programmable gate array that digitizes and processes the signal allows to perform precise time-of-flight and gamma-ray energy measurements. The gamma-ray spectramore » are unfolded into pure elemental count proportions, mainly C, N, O, Fe, Al, Si, and Ca. The C, N, and O count fractions are converted into chemical proportions, taking into account the gamma-ray production cross sections, as well as neutron and photon attenuation in the different shields between the ROV (Remotely Operated Vehicle) and the explosive, such as the explosive iron shell, seawater, and ROV envelop. A two-dimensional (2D) barycentric representation of the C, N, and O proportions is built from their chemical ratios, and a 2D likelihood map is built from the associated statistical and systematic uncertainties. The threat level is evaluated from the best matching materials of a database including explosives. (authors)« less

Deep sea habitats in the chemical warfare dumping areas of the Baltic Sea.

PubMed

Czub, Michał; Kotwicki, Lech; Lang, Thomas; Sanderson, Hans; Klusek, Zygmunt; Grabowski, Miłosz; Szubska, Marta; Jakacki, Jaromir; Andrzejewski, Jan; Rak, Daniel; Bełdowski, Jacek

2018-03-01

The Baltic Sea is a severely disturbed marine ecosystem that has previously been used as a dumping ground for Chemical Warfare Agents (CW). The presence of unexploded underwater ordnance is an additional risk factor for offshore activities and an environmental risk for the natural resources of the sea. In this paper, the focus is on descriptions of the marine habitat based on the observations arising from studies linked to the CHEMSEA, MODUM and DAIMON projects. Investigated areas of Bornholm, Gotland and Gdańsk Deeps are similarly affected by the Baltic Sea eutrophication, however, at depths greater than 70m several differences in local hydrological regimes and pore-water heavy metal concentrations between those basins were observed. During the lifespan of presented studies, we were able to observe the effects of Major Baltic Inflow, that started in December 2014, on local biota and their habitats, especially in the Bornholm Deep area. Reappearance of several meiofauna taxa and one macrofauna specimen was observed approximately one year after this phenomenon, however it's ecological effects already disappeared in March 2017. According to our findings and to the EUNIS Habitat Classification, the three reviewed areas should be characterized as Deep Sea Muddy Sands, while the presence of suspicious bomb-like objects both beneath and on top of the sediments confirms their CW dumpsite status. Copyright © 2017 Elsevier B.V. All rights reserved.

Unique Construction and Social Experiences in Residential Remediation Sites - 13423

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jung, Paul; Scarborough, Rebecca

2013-07-01

Sevenson Environmental Services, Inc., (Sevenson) has performed several radiological remediation projects located in residential urban areas. Over the course of these projects, there has been a wide variety of experiences encountered from construction related issues to unique social situations. Some of the construction related issues included the remediation of interior basements where contaminated material was located under the footers of the structure or was used in the mortar between cinder block or field stone foundations. Other issues included site security, maintaining furnaces or other utilities, underpinning, backfilling and restoration. In addition to the radiological hazards associated with this work theremore » were occupational safety and industrial hygiene issues that had to be addressed to ensure the safety and health of neighboring properties and residents. The unique social situations at these job sites have included arson, theft/stolen property, assault/battery, prostitution, execution of arrest warrants for residents, discovery of drugs and paraphernalia, blood borne pathogens, and unexploded ordnance. Some of these situations have become a sort of comical urban legend throughout the organization. One situation had historical significance, involving the demolition of a house to save a tree older than the Declaration of Independence. All of these projects typically involve the excavation of early 20. century items such as advertisement signs, various old bottles (milk, Listerine, perfume, whisky) and other miscellaneous common trash items. (authors)« less

High energy laser demonstrators for defense applications

NASA Astrophysics Data System (ADS)

Jung, M.; Riesbeck, Th.; Schmitz, J.; Baumgärtel, Th.; Ludewigt, K.; Graf, A.

2017-01-01

Rheinmetall Waffe Munition has worked since 30 years in the area of High Energy Laser (HEL) for defence applications, starting from pulsed CO2 to pulsed glass rods lasers. In the last decade Rheinmetall Waffe Munition changed to diode pumped solid state laser (DPSSL) technology and has successfully developed, realised and tested a variety of versatile HEL weapon demonstrators for air- and ground defence scenarios like countering rocket, artillery, mortar, missile (RAMM), unmanned aerial systems (UAS) and unexploded ordnances clearing. By employing beam superimposing technology and a modular laser weapon concept, the total optical power has been successively increased. Stationary weapon platforms, military vehicles and naval platforms have been equipped with high energy laser effectors. The contribution gives a summary of the most recent development stages of Rheinmetalls HEL weapon program. In addition to the stationary 30 kW laser weapon demonstrator, we present vehicle based HEL demonstrators: the 5 kW class Mobile HEL Effector Track V, the 20 kW class Mobile HEL Effector Wheel XX and the 50 kW class Mobile HEL Effector Container L and the latest 10 kW HEL effector integrated in the naval weapon platform MLG 27. We describe the capabilities of these demonstrators against different potential targets. Furthermore, we will show the capability of the 30 kW stationary Laser Weapon Demonstrator integrated into an existing ground based air defence system to defeat saturated attacks of RAMM and UAS targets.

Observations of Munitions Mobility During a Nor'easter at Wallops Island

NASA Astrophysics Data System (ADS)

Swann, C.; Frank, D. P.; Braithwaite, E. F., III; Hagg, R. K.; Calantoni, J.

2017-12-01

Unexploded ordnance (or munitions) may migrate, bury, or become exposed over time, and may pose a hazard to both humans and environment. Understanding the behavior of munitions under various wave and current conditions is central to management and remediation of contaminated underwater sites. We embedded Inertial Measurement Units (IMUs) into inert replicas of large caliber munitions (81 mm - 155 mm), herein referred to as `smart munitions'. Several smart munitions were deployed in the field with IMUs logging at 16 Hz continuously. Simultaneously the local hydrodynamic conditions were monitored to correlate any resulting munitions mobility. Here, we present the response of the smart munitions to wave and current conditions observed during a nor'easter off the coast of Wallops Island, Virginia USA in about 10 m water depth. During the nor'easter, peak significant wave heights of 2.8 m were observed in 10 m water depth. Over a roughly 10-hour period, an 81 mm smart munition migrated approximately 206 ft in a net onshore direction. Displacement and heading of the migrated smart munition were estimated by divers during the recovery. Integration of the trajectory of motion for the smart munition using a custom signal processing algorithm was in good agreement with the diver measurements. Discussion will focus on the relationship of the local sediment type and the potential for munitions mobility.

The application of induced polarization techniques to detect metal-bearing offshore anthropogenic waste and unexploded ordnance

USGS Publications Warehouse

Wynn, Jeff; Roberts, William

2009-01-01

Raw sewage and industrial waste have been dumped into sensitive estuaries, bays, and sounds for centuries. The full extents of the resulting sludge deposits are largely unknown, because they move in response to tidal and long‐shore currents, and because they are often buried by younger inert sediments. USGS field and laboratory measurements of toxic mine waste and organic effluent samples suggest that anthropogenic wastes typically contain finely‐divided metal and metal‐sulfide particles. The anoxic environment provided by anthropogenic wastes promotes the growth of anaerobic bacteria, creating a self‐reducing environment. We suggest that the finely‐divided metal and metal‐sulfide particles are the products of bacterial reduction and precipitation. The fine‐grained metallic precipitates are ideal targets for a surface‐effect electrochemical detection methodology called Induced Polarization (IP). A USGS‐patented (1998/2001) marine IP streamer technology has recently been commercialized and used to map “black smoker” sulfide deposits and their disseminated halos in the Bismarck Sea (2005), and titanium‐sand deposits offshore of South Africa (2007). The marine induced polarization system can do this mapping in three dimensions, more rapidly (it is towed at 3 knots), and with far higher resolution that land‐based measurements or vibracoring. Laboratory‐scale studies at the USGS suggest that anthropogenic wastes may display a specific multi‐frequency IP spectral signature that may be applicable to waste‐deposit mapping.

A Complex Approach to UXO Discrimination: Combining Advanced EMI Forward Models and Statistical Signal Processing

DTIC Science & Technology

2012-01-01

discrimination at live-UXO sites. Namely, under this project first we developed and implemented advanced, physically complete forward EMI models such as, the...detection and discrimination at live-UXO sites. Namely, under this project first we developed and implemented advanced, physically complete forward EMI...Shubitidze of Sky Research and Dartmouth College, conceived, implemented , and tested most of the approaches presented in this report. He developed

UXO Detection and Characterization using new Berkeley UXO Discriminator (BUD)

NASA Astrophysics Data System (ADS)

Gasperikova, E.; Morrison, H. F.; Smith, J. T.; Becker, A.

2006-05-01

An optimally designed active electromagnetic system (AEM), Berkeley UXO Discriminator, BUD, has been developed for detection and characterization of UXO in the 20 mm to 150 mm size range. The system incorporates three orthogonal transmitters, and eight pairs of differenced receivers. The transmitter-receiver assembly together with the acquisition box, as well as the battery power and GPS receiver, is mounted on a small cart to assure system mobility. BUD not only detects the object itself but also quantitatively determines its size, shape, orientation, and metal content (ferrous or non-ferrous, mixed metals). Moreover, the principal polarizabilities and size of a metallic target can be determined from a single position of the BUD platform. The search for UXO is a two-step process. The object must first be detected and its location determined then the parameters of the object must be defined. A satisfactory classification scheme is one that determines the principal dipole polarizabilities of a target. While UXO objects have a single major polarizability (principal moment) coincident with the long axis of the object and two equal transverse polarizabilities, the scrap metal has all three principal moments entirely different. This description of the inherent polarizabilities of a target is a major advance in discriminating UXO from irregular scrap metal. Our results clearly show that BUD can resolve the intrinsic polarizabilities of a target and that there are very clear distinctions between symmetric intact UXO and irregular scrap metal. Target properties are determined by an inversion algorithm, which at any given time inverts the response to yield the location (x, y, z) of the target, its attitude and its principal polarizabilities (yielding an apparent aspect ratio). Signal-to-noise estimates (or measurements) are interpreted in this inversion to yield error estimates on the location, attitude and polarizabilities. This inversion at a succession of times provides the polarizabilities as a function of time, which can in turn yield the size, true aspect ratio and estimates of the conductivity and permeability of the target. The accuracy of these property estimates depends on the time window over which the polarizability measurements, and their accuracies, are known. Initial tests at a local site over a variety of test objects and inert UXOs showed excellent detection and characterization results within the predicted size-depth range. This research was funded by the U.S. Department of Defense under ESTCP Project # UX-0437.

Automated Hand-Held UXO Detection, Classification & Discrimination Sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bell, Thomas H.

2000-06-12

The research focused on procedures for target discrimination and classification using hand-held EMI sensors. The idea is to have a small, portable sensor that can be operated in a sweep or similar pattern in front of the operator, and that is capable of distinguishing between buried UXO and clutter on the spot. Curing Phase 1, we developed the processing techniques for distinguishing between buried UXO and clutter using the EM61-HH hand-held metal detector.

Coaxial EMI Sensor for UXO Detection and Discrimination

DTIC Science & Technology

2008-05-01

Raleigh, North Carolina. Geophex has a 10 m x 10 m test bed in which 21 metal pipes of various sizes, some ferrous (steel) and some nonferrous (3...spectral matching was expected to lower the FAR, but with the wide range of anticipated UXO in terms of size and metal content, the corresponding wide...warrant further investigation.” Grid squares with a response stage below the stated noise threshold are declared empty (neither UXO nor metallic

Berkeley UXO Discriminator (BUD)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, Erika; Smith, J. Torquil; Morrison, H. Frank

2007-01-01

The Berkeley UXO Discriminator (BUD) is an optimally designed active electromagnetic system that not only detects but also characterizes UXO. The system incorporates three orthogonal transmitters and eight pairs of differenced receivers. it has two modes of operation: (1) search mode, in which BUD moves along a profile and exclusively detects targets in its vicinity, providing target depth and horizontal location, and (2) discrimination mode, in which BUD, stationary above a target, from a single position, determines three discriminating polarizability responses together with the object location and orientation. The performance of the system is governed by a target size-depth curve.more » Maximum detection depth is 1.5 m. While UXO objects have a single major polarizability coincident with the long axis of the object and two equal transverse polarizabilities, scrap metal has three different principal polarizabilities. The results clearly show that there are very clear distinctions between symmetric intact UXO and irregular scrap metal, and that BUD can resolve the intrinsic polarizabilities of the target. The field survey at the Yuma Proving Ground in Arizona showed excellent results within the predicted size-depth range.« less

78 FR 55216 - Safety Zone: Suisun Bay Electromagnetic Scan and Ordnance Recovery, Suisun Bay, Concord, CA

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-10

...-AA00 Safety Zone: Suisun Bay Electromagnetic Scan and Ordnance Recovery, Suisun Bay, Concord, CA AGENCY... (MOTCO) electromagnetic scan and ordnance recovery operations. These safety zones are established to... 10, 2013 that they intend to conduct an intrusive electromagnetic scan and ordnance recovery...

Inversion of High Frequency Acoustic Data for Sediment Properties Needed for the Detection and Classification of UXOs

DTIC Science & Technology

2015-05-26

FINAL REPORT Inversion of High Frequency Acoustic Data for Sediment Properties Needed for the Detection and Classification of UXOs SERDP...DOCUMENTATION PAGE Prescribed by ANSI Std. Z39.18 Form Approved OMB No. 0704-0188 The public reporting burden for this collection of information is...2015 Inversion of High Frequency Acoustic Data for Sediment Properties Needed for the Detection and Classification of UXO’s W912HQ-12-C-0049 MR

Statistical Tools for Designing Initial and Post-Removal UXO Characterization Surveys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsipher, Brent A.; Gilbert, Richard O.; Wilson, John E.

2002-09-06

The Department of Defense (DoD) is in the process of assessing and remediating closed, transferred, and transferring ranges. It is estimated that over 20 million acres of land in the United States potentially contain UXO. The release of DoD sites for public use will require high confidence that UXO is not present. This high confidence may be achieved solely from an extensive knowledge of historical site operations as documented in the conceptual site model or in combination with geophysical sensor surveys designed to have a sufficiently high probability of finding UXO contaminated zones. Many of these sites involve very largemore » geographical areas such that it is often impractical and/or cost prohibitive to perform 100% surveys of the entire site of interest. In that case, it is necessary to be explicit about the performance required of a survey that covers less than 100% of the site.« less

Method and apparatus for optimized sampling of volatilizable target substances

DOEpatents

Lindgren, Eric R.; Phelan, James M.

2002-01-01

An apparatus for capturing, from gases such as soil gas, target analytes. Target analytes may include emanations from explosive materials or from residues of explosive materials. The apparatus employs principles of sorption common to solid phase microextraction, and is best used in conjunction with analysis means such as a gas chromatograph. To sorb target analytes, the apparatus functions using various sorptive structures to capture target analyte. Depending upon the embodiment, those structures may include 1) a conventional solid-phase microextraction (SPME) fiber, 2) a SPME fiber suspended in a capillary tube (with means provided for moving gases through the capillary tube so that the gases come into close proximity to the suspended fiber), and 3) a capillary tube including an interior surface on which sorptive material (similar to that on the surface of a SPME fiber) is supported (along with means for moving gases through the capillary tube so that the gases come into close proximity to the sorptive material). In one disclosed embodiment, at least one such sorptive structure is associated with an enclosure including an opening in communication with the surface of a soil region potentially contaminated with buried explosive material such as unexploded ordnance. Emanations from explosive materials can pass into and accumulate in the enclosure where they are sorbed by the sorptive structures. Also disclosed is the use of heating means such as microwave horns to drive target analytes into the soil gas from solid and liquid phase components of the soil.

Years of life lost among Iranian people killed in the Iraq-Iran war: the 25-year perspective.

PubMed

Mousavi, Batool; Moradi-Lakeh, Maziar; Karbakhsh, Mojgan; Soroush, Mohammadreza

2014-01-01

To estimate the years of life lost (YLL), registered deaths due to Iraq-Iran war (1980-2005) were identified considering ICD10 codes of Y36.0 to Y36.9. Estimated YLL was calculated by taking age-weighting options and discount rates. Population life expectancy in each corresponding year was retrieved from the national health database. During 1980-2005, 178,298 Iranian men and 5325 Iranian women died in war. The mean death age was 22.8 ± 9 years, 96.6% occurred during the years of war (September 1980-August 1988). In the years after the war (1988-2005) 6243 (3.4%) of deaths occurred as the result of complication of the war-related injuries or implanted landmines/unexploded ordnances (ICD10 code: Y36.8). YLL in Iraq-Iran war among Iranian victims were calculated as 10,479,405.0 years considering the age weighting and discount rate equal to 0. Age-adjusted YLL were estimated as 10,169,546.2 years in males. Female cases that comprised 2.9% of total victims lost 309,858.8 years. The mean YLL was calculated as 57.1 years for each Iranian victim killed in Iraq-Iran war. The war-related YLL was estimated more than 10 million years that comprised a majority of young men. This study is the first step in estimation of disability adjusted life year (DALY) of Iraq-Iran war on Iranian side.

Electromagnetic Induction E-Sensor for Underwater UXO Detection

DTIC Science & Technology

2011-12-01

EMF Electromotive force FET Field Effect Transitor Hz Hertz ms millisecond nV nanoVolt QFS QUASAR Federal...processing. Statistical discrimination techniques based on model analysis, such as the Time-Domain Three Dipole (TD3D) model, can separate UXO-like objects

Financial Management: Ordnance Accountability at Fleet Combat Training Center Atlantic (D-2003-084)

DTIC Science & Technology

2003-04-29

13, 1994. This report is the third report in a series resulting from an audit of the financial reporting of operating materials and supplies. The first...report discusses the Naval Air System Command’s financial reporting of non-ordnance operating materials and supplies. The second report discusses...Navy efforts to improve the financial reporting of its conventional ordnance portion of operating materials and supplies and its conventional ordnance

TEMTADS Adjunct Sensor Systems Hand-Held EMI Sensor for Cued UXO Discrimination (ESTCP MR-200807) and Man-Portable EMI Array for UXO Detection and Discrimination (ESTCP MR-200909)

DTIC Science & Technology

2012-04-05

C la ss ifi ca tio n TY PE D ep th (M ) A zi m ut h (D eg re es ) D ip (D eg re es ) 1 2 3...Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/ 6110 --12-9401 TEMTADS Adjunct Sensor Systems Hand-held EMI Sensor for Cued UXO...NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 2 . REPORT TYPE1. REPORT DATE (DD-MM-YYYY) 4

TEMTADS Adjunct Sensor Systems Hand-held EMI Sensor for Cued UXO Discrimination (ESTCP MR-200807) and Man-Portable EMI Array for UXO Detection and Discrimination (ESTCP MR-200909) Cost and Performance Report

DTIC Science & Technology

2012-06-27

notes and team orienteering functions. Data collection with the MP system at the former Camp Beale, CA is shown in Figure 5- 2 (right). 5.3.3...Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/ 6110 --12-9424 TEMTADS Adjunct Sensor Systems Hand-held EMI Sensor for Cued UXO...CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 2 . REPORT TYPE1. REPORT DATE (DD

UXO Forum 1996

DTIC Science & Technology

1996-01-01

used to locate and characterize a magnetic dipole source, and this finding accelerated the development of superconducting tensor gradiometers for... superconducting magnetic field gradiometer, two-color infrared camera, synthetic aperture radar, and a visible spectrum camera. The combination of these...Pieter Hoekstra, Blackhawk GeoSciences ......................................... 68 Prediction for UXO Shape and Orientation Effects on Magnetic

75 FR 2490 - Taking and Importing Marine Mammals; Naval Explosive Ordnance Disposal School Training Operations...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-15

... Importing Marine Mammals; Naval Explosive Ordnance Disposal School Training Operations Activities at Eglin...) for authorization to take marine mammals, by harassment, incidental to Naval Explosive Ordnance Disposal School (NEODS) training operations, military readiness activities, at Eglin AFB, FL from...

Joint Electromagnetic Spectrum Management Operations

DTIC Science & Technology

2012-03-20

electromagnetic radiation to ordnance ( HERO ), hazards of electromagnetic radiation to fuels (HERF), and natural phenomena effects of lightning and...fuels HERO hazards of electromagnetic radiation to ordnance HERP hazards of electromagnetic radiation to personnel HF high frequency HN host... electromagnetic pulse (EMP); hazards of EM radiation to personnel, ordnance ,

Electromagnetic Spectrum Test and Evaluation Process

DTIC Science & Technology

2010-01-01

HERO , hazards of electromagnetic radiation to ordnance ; HERP, hazards of electromagnetic radiation to personnel; HERF, hazards of electromagnetic ... electromagnetic pulse (EMP); electronic protection; electrostatic dis- charge (ESD); hazards of electromagnetic radi- ation to personnel (HERP), ordnance ...including ordnance containing electrically initiated devices, to be mutually compatible in their intended

77 FR 25435 - Taking and Importing Marine Mammals; Naval Explosive Ordnance Disposal School Training Operations...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-30

... B harassment, incidental to Naval Explosive Ordnance Disposal School (NEODS) training operations at... Importing Marine Mammals; Naval Explosive Ordnance Disposal School Training Operations at Eglin Air Force... and the Issuance of Letters of Authorization to Take Marine Mammals, by Level B Harassment, Incidental...

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse in possession of MacDill Air Force Base, Civil Engineering, Tampa, Florida; 1940 architectural drawings by Construction Division, Office of the Quartermaster General)TRUSS DETAILS - MacDill Air Force Base, Signal & Ordnance Warehouse, 7620 Hanger Loop Drive, Tampa, Hillsborough County, FL

Engineering Evaluation of UXO Detection Technologies and Interrogation Methodologies for Use in Panama: Empire, Balboa West and Pina Ranges

DTIC Science & Technology

1998-07-01

7 2.5 PLANT AND ANIMAL SPECIES...False Alarm Ratio (FAR) ...................................................................... 5 Table 2-1 Plant And Animal Species Found On Areas...be effected by the implementation of UXO detection and interrogation technologies. The ranges contain many species of plants , mammals, and birds

SERDP/Office of Naval Research Workshop on Acoustic Detection and Classification of UXO in the Underwater Environment

DTIC Science & Technology

2013-09-01

of combat operations A maritime wreck An artificial reef The Navy considers munitions located in waters between high and low tides terrestrial...e.g., operational areas, beach assess). UXO are cleared to provide for civilian safety (e.g., fisheries, diving , cable and pipeline laying

Multifractal Characterization of Geologic Noise for Improved UXO Detection and Discrimination

DTIC Science & Technology

2008-03-01

12 Recovery of the Universal Multifractal Parameters ...dipole-model to each magnetic anomaly and compares the extracted model parameters with a library of UXO items. They found that remnant magnetization...the survey parameters , and the geologic environment. In this pilot study we have focused on the multifractal representation of natural variations

Hand-held EMI Sensor for Cued UXO Discrimination Man-Portable EMI Array for UXO Detection and Discrimination

DTIC Science & Technology

2012-03-01

collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE MAR 2012 2 . REPORT TYPE 3. DATES COVERED...1 1.4 IMPLEMENTATION ISSUES .............................................................................. 2 2.0...assembled sensor with end caps attached. ................................................................................ 5 Figure 2 . Construction details

Automatic detection of multiple UXO-like targets using magnetic anomaly inversion and self-adaptive fuzzy c-means clustering

NASA Astrophysics Data System (ADS)

Yin, Gang; Zhang, Yingtang; Fan, Hongbo; Ren, Guoquan; Li, Zhining

2017-12-01

We have developed a method for automatically detecting UXO-like targets based on magnetic anomaly inversion and self-adaptive fuzzy c-means clustering. Magnetic anomaly inversion methods are used to estimate the initial locations of multiple UXO-like sources. Although these initial locations have some errors with respect to the real positions, they form dense clouds around the actual positions of the magnetic sources. Then we use the self-adaptive fuzzy c-means clustering algorithm to cluster these initial locations. The estimated number of cluster centroids represents the number of targets and the cluster centroids are regarded as the locations of magnetic targets. Effectiveness of the method has been demonstrated using synthetic datasets. Computational results show that the proposed method can be applied to the case of several UXO-like targets that are randomly scattered within in a confined, shallow subsurface, volume. A field test was carried out to test the validity of the proposed method and the experimental results show that the prearranged magnets can be detected unambiguously and located precisely.

Development of a Laser for Landmine Destruction Final Report CRADA No. TC02126.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, R.; Sheppard, C.

2017-08-31

This was one of two CRADAs between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and First Alliance Technologies, LLC (First Alliance), to conduct research and development activity toward an integrated system for the detecting, locating, and destroying of landmines and unexploded ordinance using a laser to destroy landmines and unexploded ordinance and First Alliance’s Land Mine Locator (LML) system.

Electromagnetic Radiation Hazards Testing for Non-Ionizing Radio Frequency Transmitting Equipment

DTIC Science & Technology

2012-12-19

Hazards of Electromagnetic Radiation to Ordnance (HERO), Personnel (HERP), and Fuel (HERF) protection guidance for intentional non-ionizing Radio...HERO Hazards of Electromagnetic Radiation to Ordnance HERP Hazards of Electromagnetic Radiation to Personnel IEEE Institute of Electrical and...Systems Command Technical Manual, Electromagnetic Radiation Hazards ( Hazards to Ordnance ), 1 July 2008.

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse in possession of MacDill Air Force Base, Civil Engineering, Tampa, Florida; 1940 architectural drawings by Construction Division, Office of the Quartermaster General) SECTIONS AND DETAILS - MacDill Air Force Base, Signal & Ordnance Warehouse, 7620 Hanger Loop Drive, Tampa, Hillsborough County, FL

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing (original drawing of Signal & Ordnance Warehouse in possession of MacDill Air Force Base, Civil Engineering, Tampa, Florida; 1940 architectural drawings by Construction Division, Office of the Quartermaster General) PLANS, ELEVATIONS, SECTIONS AND DETAILS - MacDill Air Force Base, Signal & Ordnance Warehouse, 7620 Hanger Loop Drive, Tampa, Hillsborough County, FL

Flight demonstration of laser diode initiated ordnance

NASA Technical Reports Server (NTRS)

Boucher, Craig J.; Schulze, Norman R.

1995-01-01

A program has been initiated by NASA Headquarters to validate laser initiated ordnance in flight applications. The primary program goal is to bring together a team of government and industry members to develop a laser initiated ordnance system having the test and analysis pedigree to be flown on launch vehicles. The culmination of this effort was a flight of the Pegasus launch vehicle which had two fin rockets initiated by this laser system. In addition, a laser initiated ordnance squib was fired into a pressure bomb during thrusting flight. The complete ordnance system comprising a laser diode firing unit, fiber optic cable assembly, laser initiated detonator, and laser initiated squib was designed and built by The Ensign Bickford Company. The hardware was tested to the requirements of the Pegasus launch vehicle and integrated into the vehicle by The Ensign Bickford Company and the Orbital Sciences Corporation. Discussions include initial program concept, contract implementation, team member responsibilities, analysis results, vehicle integration, safing architecture, ordnance interfaces, mission timeline and telemetry data. A complete system description, summary of the analyses, the qualification test results, and the results of flight are included.

Demonstration Report: ESTCP UXO Discrimination Study ESTCP PROJECT # MM-0838

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, Erika

2010-02-15

In 2003, the Defense Science Board observed: 'The problem is that instruments that can detect the buried UXOs also detect numerous scrap metal objects and other artifacts, which leads to an enormous amount of expensive digging. Typically 100 holes may be dug before a real UXO is unearthed! The Task Force assessment is that much of this wasteful digging can be eliminated by the use of more advanced technology instruments that exploit modern digital processing and advanced multi-mode sensors to achieve an improved level of discrimination of scrap from UXOs.' Significant progress has been made in discrimination technology. To date,more » testing of these approaches has been primarily limited to test sites with only limited application at live sites. Acceptance of discrimination technologies requires demonstration of system capabilities at real UXO sites under real world conditions. Any attempt to declare detected anomalies to be harmless and requiring no further investigation will require demonstration to regulators of not only individual technologies, but of an entire decision making process. This characterization study was be the second phase in what is expected to be a continuing effort that will span several years. The FY06 Defense Appropriation contained funding for the 'Development of Advanced, Sophisticated, Discrimination Technologies for UXO Cleanup' in the Environmental Security Technology Certification Program (ESTCP). ESTCP responded by conducting a UXO Discrimination Study at the former Camp Sibert, AL. The results of this first demonstration were very encouraging. Although conditions were favorable at this site, a single target of interest (4.2-in mortar) and benign topography and geology, all of the classification approaches demonstrated were able to correctly identify a sizable fraction of the anomalies as arising from non-hazardous items that could be safely left in the ground. To build upon the success of the first phase of this study, ESTCP sponsored a second study in 2009 at the former Camp San Luis Obispo, CA, a site with more challenging topography and a wider mix of targets-of-interest (TOI). There were two primary objectives of this study: (1) Test and validate detection and discrimination capabilities of currently available and emerging technologies on real sites under operational conditions; and (2) Investigate in cooperation with regulators and program managers how discrimination technologies can be implemented in cleanup operations.« less

Potential health impacts from range fires at Aberdeen Proving Ground, Maryland.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willians, G.P.; Hermes, A.M.; Policastro, A.J.

1998-03-01

This study uses atmospheric dispersion computer models to evaluate the potential for human health impacts from exposure to contaminants that could be dispersed by fires on the testing ranges at Aberdeen Proving Ground, Maryland. It was designed as a screening study and does not estimate actual human health risks. Considered are five contaminants possibly present in the soil and vegetation from past human activities at APG--lead, arsenic, trichloroethylene (TCE), depleted uranium (DU), and dichlorodiphenyltrichloroethane (DDT); and two chemical warfare agents that could be released from unexploded ordnance rounds heated in a range fire--mustard and phosgene. For comparison, dispersion of twomore » naturally occurring compounds that could be released by burning of uncontaminated vegetation--vinyl acetate and 2-furaldehyde--is also examined. Data from previous studies on soil contamination at APG are used in conjunction with conservative estimates about plant uptake of contaminants, atmospheric conditions, and size and frequency of range fires at APG to estimate dispersion and possible human exposure. The results are compared with US Environmental Protection Agency action levels. The comparisons indicate that for all of the anthropogenic contaminants except arsenic and mustard, exposure levels would be at least an order of magnitude lower than the corresponding action levels. Because of the compoundingly conservative nature of the assumptions made, they conclude that the potential for significant human health risks from range fires is low. The authors recommend that future efforts be directed at fire management and control, rather than at conducting additional studies to more accurately estimate actual human health risk from range fires.« less

A Wide Area Risk Assessment Framework for Underwater Military Munitions Response

NASA Astrophysics Data System (ADS)

Holland, K. T.; Calantoni, J.

2017-12-01

Our objective was to develop a prototype statistical framework supporting Wide Area Assessment and Remedial Investigation decisions relating to the risk of unexploded ordnance and other military munitions concentrated in underwater environments. Decision making involving underwater munitions is inherently complex due to the high degree of uncertainty in the environmental conditions that force munitions responses (burial, decay, migration, etc.) and associated risks to the public. The prototype framework provides a consistent approach to accurately delineating contaminated areas at underwater munitions sites through the estimation of most probable concentrations. We adapted existing deterministic models and environmental data services for use within statistical modules that allowed the estimation of munition concentration given historic site information and environmental attributes. Ultimately this risk surface can be used to evaluate costs associated with various remediation approaches (e.g. removal, monitoring, etc.). Unfortunately, evaluation of the assessment framework was limited due to the lack of enduser data services from munition site managers. Of the 450 U.S. sites identified as having potential contamination with underwater munitions, assessment of available munitions information (including historic firing or disposal records, and recent ground-truth munitions samples) indicated very limited information in the databases. Example data types include the most probable munition types, approximate firing / disposal dates and locations, and any supportive munition survey or sampling results. However the overall technical goal to integrate trained statistical belief networks with detailed geophysical knowledge of sites, of sensors and of the underwater environment was demonstrated and should allow probabilistic estimates of the most likely outcomes and tradeoffs while managing uncertainty associated with military munitions response.

Standardized UXO Technology Demonstration Site, Scoring Record No. 928

DTIC Science & Technology

2011-03-01

magnetic permittivity (possibly complex and frequency dependent), ω is radian frequency, Vrx is the voltage at the receiver coil, txn̂ and rxn̂ are the...voltage induced in the receiver coil Vrx due to the induced target dipole moment m  is related to magnetic field uxoH  at the target due to a

UXO Discrimination Using Vehicle Towed and Man Portable Sensor Data Collected at Camp Beale, California

DTIC Science & Technology

2011-11-01

UXO Discrimination Using Vehicle Towed and Man Portable Sensor Data Collected at Camp Beale, California Len Pasion , Laurens Beran, Stephen Billings...PORTABLE SENSOR DATA COLLECTED AT CAMP BEALE, CALIFORNIA LEN PASION Sky Research 112A 2386 East Mall Vancouver, BC V6T1Z3 CANADA (604) 221

Bi-Level Demand-Sensitive LED Street Lighting Systems

DTIC Science & Technology

2013-10-01

Hazards of Electromagnetic Radiation to Fuel HERO : Hazards of Electromagnetic Radiation to Ordnance ...we followed the following guidelines very strictly: 68 • For Hazards of Electromagnetic Radiation to Ordnance (HERO), RF device to be brought in...should be used at least 5 feet from ordnance /explosives. • For, Hazards of Electromagnetic Radiation to Personnel (HERP), HERP Controlled and

Software System Architecture Modeling Methodology for Naval Gun Weapon Systems

DTIC Science & Technology

2010-12-01

Weapon System HAR Hazard Action Report HERO Hazards of Electromagnetic Radiation to Ordnance IOC Initial Operational Capability... radiation to ordnance ; and combinations therein. Equipment, systems, or procedures and processes whose malfunction would hazard the safe manufacturing...NDI Non-Development Item OPEVAL Operational Evaluation ORDALTS Ordnance Alterations O&SHA Operating and Support Hazard Analysis PDA

Digital Semaphore: Tactical Implications of QR Code Optical Signaling for Fleet Communications

DTIC Science & Technology

2013-06-01

Emissions Control (EMCON) and Hazards of Electromagnetic Radiation to Ordnance (HERO) restrict the ability for Naval Vessels to communicate using...importance of visual communications methods is brought to light by discussing emissions control, hazards of electromagnetic radiation to ordnance , and...overview of emissions restrictions including Emissions Control (EMCON) and Hazards of Electromagnetic Radiation to Ordnance (HERO). Chapter VII is

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record No. 806 (U.S. Geological Survey, TMGS Magnetometer/Towed Array)

DTIC Science & Technology

2007-05-01

BOX 25046, FEDERAL CENTER, M.S. 964 DENVER, CO 80225-0046 TECHNOLOGY TYPE/PLATFORM: TMGS MAGNETOMETER/TOWED ARRAY PREPARED BY: U.S. ARMY...GEOLOGICAL SURVEY, TMGS MAGNETOMETER/TOWED ARRAY) 8-CO-160-UXO-021 Karwatka, Michael... TMGS Magnetometer/Towed Array, MEC Unclassified Unclassified Unclassified SAR (Page ii Blank) i ACKNOWLEDGMENTS

Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 489: WWII UXO Sites, Tonopah Test Range, Nevada; May 2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bechtel Nevada; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

2005-05-01

This Streamlined Approach for Environmental Restoration Plan provides the details for the closure of Corrective Action Unit (CAU) 489: WWII UXO Sites, Tonopah Test Range. CAU 489 is located at the Tonopah Test Range and is currently listed in Appendix III of the Federal Facility Agreement and Consent Order of 1996.

Improving UXO Detection and Discrimination in Magnetic Environments

DTIC Science & Technology

2010-05-01

Krahenbuhl, Todd Meglich Center for Gravity, Electrical , & Magnetic Studies Department of Geophysics Colorado School of Mines Doug Oldenburg, Len...NAME(S) AND ADDRESS(ES) Colorado School of Mines,Department of Geophysics,Center for Gravity, Electrical , & Magnetic Studies,Golden,CO,80401 8...SERDP Project MM-1414 Improving UXO Detection and Discrimination in Magnetic Environments Final Report Center for Gravity, Electrical , & Magnetic Studies

An Impaled Potential Unexploded Device in the Civilian Training Trauma Setting: A Case Report and Review of the Literature

DTIC Science & Technology

2017-12-11

responsibility.(!) 62 Additionally, eme rgency physicians need to know how to manage a patient with 63 an impaled unexploded device. Improper...his leg during the explosion. He was evaluated by EMS in 76 the field where his limb was noted to be grossly unstable with a large anterior soft 77...including roadside 127 explosives, explosive formed projectile devices and suicide bombs .(S) 128 In the United States military medical literature

LeadingEdge: Challenges and Solutions for the 21st Century, Electromagnetic Environmental Effects. Volume 7, Issue 1, 2009

DTIC Science & Technology

2009-01-01

Hazards of Electromagnet - ic Radiation to Ordnance ( HERO ). Below decks spaces, such as ammunition storage lockers and...Navy’s Hazards of Electromagnetic Radiation to Ordnance ( HERO ) program. Unlike other services deployed in our nation’s defense, our sailors liter...also provides infor- mation on other general HERO requirements. The Electromagnetic Radiation Hazards ( Hazards to Ordnance ) Datasheets2

Major General Charles Ryder: The Forging of a World War II Division Commander

DTIC Science & Technology

2014-12-04

During those four years, he studied civil and military engineering, ordnance , the science of gunnery, law, Spanish, drill regulations, practical military...Engineering Freshman Sophomore Senior Military Hygiene Junior Law Senior Ordnance and Gunnery Senior Civil and Military Engineering Senior Source...as they studied the two military topics of ordnance and gunnery. These courses were divided into three parts: theoretical, descriptive, and

An Impaled Potential Unexploded Device in the Civilian Trauma Setting: A Case Report and Review of the Literature.

PubMed

Thaut, Lane C; Murtha, Andrew S; Johnson, Anthony E; Roper, Jamie L

2018-05-01

The management of patients with impaled unexploded devices is rare in the civilian setting. However, as the lines of the traditional battlefield are blurred by modern warfare and terrorist activity, emergency providers should be familiar with facility protocols, plans, and contact information of their local resources for unexploded devices. A 44-year-old male sustained a close-proximity blast injury to his lower extremities while manipulating a mortar-type firework. He presented to the regional trauma center with an open, comminuted distal femur fracture and radiographic evidence of a potential explosive device in his thigh. His management was coordinated with the local Explosive Ordinance Disposal and the fire department. WHY SHOULD AN EMERGENCY PHYSICIAN BE AWARE OF THIS?: Explosive devices pose a grave threat when encountered. Familiarization with protocols to manage these patients can mitigate disaster. Emergency providers should expect and be prepared to coordinate care for these patients. Copyright © 2017 Elsevier Inc. All rights reserved.

Optical ordnance system for use in explosive ordnance disposal activities

NASA Technical Reports Server (NTRS)

Merson, J. A.; Salas, F. J.; Helsel, F.M.

1994-01-01

A portable hand-held solid state rod laser system and an optically-ignited detonator have been developed for use in explosive ordnance disposal (EOD) activities. Laser prototypes from Whittaker Ordnance and Universal Propulsion have been tested and evaluated. The optical detonator contains 2-(5 cyanotetrazolato) pentaamine cobalt(III) perchlorate (CP) as the DDT column and the explosive Octahydro- 1,3,5,7 - tetrazocine (HMX) as the output charge. The laser is designed to have an output of 150 mJ in a 500 microsecond pulse. This output allows firing through 2000 meters of optical fiber. The detonator can also be ignited with a portable laser diode source through a shorter length of fiber.

Explosive Remnants of War in Stability Operations

DTIC Science & Technology

2012-09-01

strategic partner capacity building, global ERW and Counter-IED (C-IED) efforts, while adhering to global Mine /UXO awareness efforts. 15. NUMBER OF...PAGES 139 14. SUBJECT TERMS Explosive Remnants of War—Collection Point (ERW - CP), Landmine, Anti- Personnel Mine , Mine Action, Cluster Munitions...strategic partner capacity building, global ERW and Counter- IED (C-IED) efforts, while adhering to global Mine /UXO awareness efforts. vi THIS PAGE

Military Retention: A Holistic Approach To Understanding Officer Separation In The Navy Explosive Ordnance Disposal Community

DTIC Science & Technology

2016-12-01

RETENTION: A HOLISTIC APPROACH TO UNDERSTANDING OFFICER SEPARATION IN THE NAVY EXPLOSIVE ORDNANCE DISPOSAL COMMUNITY by Mark D. Gutierrez December...APPROACH TO UNDERSTANDING OFFICER SEPARATION IN THE NAVY EXPLOSIVE ORDNANCE DISPOSAL COMMUNITY 5. FUNDING NUMBERS 6. AUTHOR(S) Mark D. Gutierrez 7...DISTRIBUTION CODE 13. ABSTRACT (maximum 200 words) This thesis explores and identifies trends in officer separation within the Navy Explosive

UXO Engineering Design. Technical Specification and ConceptualDesign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beche, J-F.; Doolittle, L.; Greer, J.

2005-04-23

The design and fabrication of the UXO detector has numerous challenges and is an important component to the success of this study. This section describes the overall engineering approach, as well as some of the technical details that brought us to the present design. In general, an array of sensor coils is measuring the signal generated by the UXO object in response to a stimulation provided by the driver coil. The information related to the location, shape and properties of the object is derived from the analysis of the measured data. Each sensor coil is instrumented with a waveform digitizermore » operating at a nominal digitization rate of 100 kSamples per second. The sensor coils record both the large transient pulse of the driver coil and the UXO object response pulse. The latter is smaller in amplitude and must be extracted from the large transient signal. The resolution required is 16 bits over a dynamic range of at least 140 dB. The useful signal bandwidth of the application extends from DC to 40 kHz. The low distortion of each component is crucial in order to maintain an excellent linearity over the full dynamic range and to minimize the calibration procedure. The electronics must be made as compact as possible so that the response of its metallic parts has a minimum signature response. Also because of a field system portability requirement, the power consumption of the instrument must be kept as low as possible. The theory and results of numerical and experimental studies that led to the proof-of-principle multitransmitter-multireceiver Active ElectroMagnetic (AEM) system, that can not only accurately detect but also characterize and discriminate UXO targets, are summarized in LBNL report-53962: ''Detection and Classification of Buried Metallic Objects, UX-1225''.« less

Demonstration of Advanced EMI Models for Live-Site UXO Discrimination at Waikoloa, Hawaii

DTIC Science & Technology

2015-12-01

magnetic source models PNN Probabilistic Neural Network SERDP Strategic Environmental Research and Development Program SLO San Luis Obispo...SNR Signal to noise ratio SVM Support vector machine TD Time Domain TEMTADS Time Domain Electromagnetic Towed Array Detection System TOI... intrusive procedure, which was used by Parsons at WMA, failed to document accurately all intrusive results, or failed to detect and clear all UXO like

Demonstration of UXO-PenDepth for the Estimation of Projectile Penetration Depth

DTIC Science & Technology

2010-08-01

Effects (JTCG/ME) in August 2001. The accreditation process included verification and validation (V&V) by a subject matter expert (SME) other than...Within UXO-PenDepth, there are three sets of input parameters that are required: impact conditions (Fig. 1a), penetrator properties , and target... properties . The impact conditions that need to be defined are projectile orientation and impact velocity. The algorithm has been evaluated against

Man Portable Vector EMI Sensor for Full UXO Characterization

DTIC Science & Technology

2012-05-01

with project management and coordination. Drs. Laurens Beran, Leonard Pasion , and Stephen Billings advised on technical aspects and Dr. Gregory Schultz...approximated as a point dipole (e.g., Bell et al., 2001; Pasion and Oldenburg, 2001; Gasperikova et al., 2009). The process of estimating the target...39, 1286–1293. Bell, T. 2005. Geo-location Requirements for UXO Discrimination. SERDP Geo-location Workshop. Billings, S., L. Pasion , N. Lhomme

Vortex Lattice UXO Mobility Model Integration

DTIC Science & Technology

2015-03-01

law , no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB...predictions of the fate and transport of a broad-field UXO population are extremely sensitive to the initial state of that population, specifically: the...limit the model’s computational domain. This revised model software was built on the concept of interconnected geomorphic control cells consisting of

Hand-Held UXO Discriminator

DTIC Science & Technology

2010-04-01

structure design showed that we could achieve both of these goals with a 14-in (0.35 m) sensor cube. To avoid the reliance on accurate multiple...differenced pair receiver. 4. Conclusions We have designed and built a sensor package of a 14-in (0.35 m) cube based on the...funding (UX-1225, MM-0437, and MM-0838), we have successfully designed and built a cart-mounted Berkeley UXO Discriminator (BUD) and demonstrated its

Summary of Progress on SIG Ft. Ord ESTCP DemVal

DTIC Science & Technology

2007-04-01

We report on progress under an ESTCP demonstration plan dedicated to demonstrating active learning - based UXO detection on an actual former UXO site...Ft. Ord), using EMI data. In addition to describing the details of the active - learning algorithm, we discuss techniques that were required when...terms of two dipole-moment magnitudes and two resonant frequencies. Information-theoretic active learning is then conducted on all anomalies to

Statistical methods for identifying and bounding a UXO target area or minefield

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKinstry, Craig A.; Pulsipher, Brent A.; Gilbert, Richard O.

2003-09-18

The sampling unit for minefield or UXO area characterization is typically represented by a geographical block or transect swath that lends itself to characterization by geophysical instrumentation such as mobile sensor arrays. New spatially based statistical survey methods and tools, more appropriate for these unique sampling units have been developed and implemented at PNNL (Visual Sample Plan software, ver. 2.0) with support from the US Department of Defense. Though originally developed to support UXO detection and removal efforts, these tools may also be used in current form or adapted to support demining efforts and aid in the development of newmore » sensors and detection technologies by explicitly incorporating both sampling and detection error in performance assessments. These tools may be used to (1) determine transect designs for detecting and bounding target areas of critical size, shape, and density of detectable items of interest with a specified confidence probability, (2) evaluate the probability that target areas of a specified size, shape and density have not been missed by a systematic or meandering transect survey, and (3) support post-removal verification by calculating the number of transects required to achieve a specified confidence probability that no UXO or mines have been missed.« less

Financial Management: Naval Ammunition Logistics Center Financial Reporting of Ammunition and Other Ordnance Assets in Operating Materials and Supplies for FY 2002

DTIC Science & Technology

2002-10-30

2002 Report Type N/A Dates Covered (from... to) - Title and Subtitle Financial Management: Naval Ammunition Logistics Center Financial Reporting of...October 30, 2002 Project No. D2001FJ –0179.001 Naval Ammunition Logistics Center Financial Reporting of Ammunition and Other Ordnance Assets in...it provides information concerning the financial reporting of ammunition and ordnance assets. Background. The audit was performed in support of

Hydrogeologic setting, hydraulic properties, and ground-water flow at the O-Field area of Aberdeen Proving Ground, Maryland

USGS Publications Warehouse

Banks, W.S.; Smith, B.S.; Donnelly, C.A.

1996-01-01

The U.S. Army disposed chemical agents, laboratory materials, and unexploded ordnance at O-Field in the Edgewood area of Aberdeen Proving Ground, Maryland, from before World War II until at least the 1950's. Soil, ground water, surface water,and wetland sediments in the O-Field area were contaminated from the disposal activity. A ground-water-flow model of the O-Field area was constructed by the U.S. Geological Survey (USGS) in 1989 to simulate flow in the central and southern part of the Gunpowder Neck. The USGS began an additional study of the contamination in the O-Field area in cooperation with the U.S. Army in 1990 to (1) further define the hydrogeologic framework of the O-Field area, (2) characterize the hydraulic properties of the aquifers and confining units, and (3) define ground-water flow paths at O-Field based on the current data and simulations of ground-water flow. A water-table aquifer, an upper confining unit, and an upper confined aquifer comprise the shallow ground-water aquifer system of the O-Field area. A lower confining unit, through which ground-water movement is negligible, is considered a lower boundary to the shallow aquifer system. These units are all part of the Pleistocene Talbot Formation. The model developed in the previous study was redesigned using the data collected during this study and emphasized New O-Field. The current steady-state model was calibrated to water levels of June 1993. The rate of ground-water flow calculated by the model was approximately 0.48 feet per day (ft/d) and the rate determined from chlorofluorocarbon dates was approximately 0.39 ft/d.

Data acquisition and analysis of the UNCOSS underwater explosive neutron sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carasco, C.; Eleon, C.; Perot, B.

2011-07-01

The purpose of the FP7 UNCOSS project (Underwater Coastal Sea Surveyor, http://www.uncoss-project.org) is to develop a neutron-based underwater explosive sensor to detect unexploded ordnance lying on the sea bottom. The Associated Particle Technique is used to focus the inspection on a suspicious object located by optical and electromagnetic sensors and to determine if there is an explosive charge inside. This paper presents the data acquisition electronics and data analysis software which have been developed for this project. The electronics digitize and process the signal in real-time based on a field programmable gate array structure to perform precise time-of-flight and gamma-raymore » energy measurements. UNCOSS software offers the basic tools to analyze the time-of-flight and energy spectra of the interrogated object. It allows to unfold the gamma-ray spectrum into pure elemental count proportions, mainly C, N, O, Fe, Al, Si, and Ca. The C, N, and O count fractions are converted into chemical proportions by taking into account the gamma-ray production cross sections, as well as neutron and photon attenuation in the different shields between the ROV (Remotely Operated Vehicle) and the explosive, such as the explosive iron shell, seawater, and ROV envelop. These chemical ratios are plotted in a two-dimensional (2D) barycentric representation to position the measured point with respect to common explosives. The systematic uncertainty due to the above attenuation effects and counting statistical fluctuations are combined with a Monte Carlo method to provide a 3D uncertainty area in a barycentric plot, which allows to determine the most probable detected materials in view to make a decision about the presence of explosive. (authors)« less

Mortality and injuries among Iranians in Iraq-Iran war: a systematic review.

PubMed

Salamati, Payman; Razavi, Seyed Mansour; Shokraneh, Farhad; Mohazzab Torabi, Saman; Laal, Marjan; Hadjati, Gholamreza; Khaji, Ali; Rahimi Movaghar, Vafa

2013-09-01

The Iraq-Iran war was one of the longest conflicts in the twentieth century. The aim of our research was to review the incidence of mortality and injuries of the war. A search strategy was designed and run in Medline, EMBASE, Scopus, and Iranian databases including Scientific Information Database (SID), IranMedex, and Magiran. Also, searching grey literature, checking references, tracking citations, hand-searching of focused journals, and websites were utilized for retrieval of related studies. All of articles which studied epidemiology of mortality or injuries of the war were included. The excluding criteria were case reports, case series, laboratory researches, and nonoriginal studies. Fourteen articles out of 1751 primary results were selected to be included in the study. During the war (1980 - 1988), 188,015 to 217,489 Iranians were killed (about 70 people per day). The mean age of mortality was 23 years. Six thousand four hundred twenty-seven (2.9%) of those who died during the war were females. One thousand five chemical warfare victims died between 1983 and 1994. From 1985 through 1998, 82 veterans had successful suicides too. At the end of war, we had 398, 587 veterans who needed follow- up. Among them, there were 52,000 chemical warfare victims. Between 1988 and 2003, 1400 people died and 2313 injured due to landmines and unexploded ordnances in five border provinces. The war caused a lot of mortalities and morbidities in our country. Now, 24 years after the war, many physically, mentally, and chemically injured victims have remained. We suggest other studies about indirect impacts of the war on societies, families, friends, and affiliates of the victims.

Sonar Detection and Classification of Underwater UXO and Environmental Parameters

DTIC Science & Technology

2012-07-09

For these targets, representations like those in Figs. 10 and 11 may be more useful because they focus on properties of the isolated target signal ... using time-frequency phenomena extracted from strong ROIs in target scattering data. In general, backscattered signals contain specular as well as...database of sonar target signals useful for developing and evaluating C/ID algorithms that separate UXO from bottom clutter and to look for and

Demonstration Report: Handheld UXO Discriminator, SERDP No. MR-1667

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, E.

2010-09-01

In 2003, the Defense Science Board observed: 'The problem is that instruments that can detect the buried UXOs also detect numerous scrap metal objects and other artifacts, which leads to an enormous amount of expensive digging. Typically 100 holes may be dug before a real UXO is unearthed! The Task Force assessment is that much of this wasteful digging can be eliminated by the use of more advanced technology instruments that exploit modern digital processing and advanced multi-mode sensors to achieve an improved level of discrimination of scrap from UXOs.' In keeping with these remarks and with prior funding (UX-1225,more » MM-0437, and MM-0838), the LBNL group has successfully designed and built the cart-mounted Berkeley UXO Discriminator (BUD) and demonstrated its performance at various test sites (cf. Gasperikova et al., 2007, 2008, and 2009). Because hand-held systems have the advantage of being lightweight, compact, portable, and deployable under most site conditions, they are particularly useful in areas of dense vegetation or challenging terrain. In heavily wooded areas or areas with steep or uneven terrain, hand-held sensors may be the only suitable device for UXO detection and discrimination because it can be carried through spaces that the operator could walk through or at least approach. Furthermore, it is desirable to find and characterize a metallic object without the need to accurately locate the sensors at multiple positions around the target. The ideal system would thus locate and characterize the target from a single position of the sensor and indicate to the operator where to flag the target for subsequent study. Based on these considerations, we designed and built a sensor package in a shape of a 14-in (0.35 m) cube. This hand-held prototype incorporates the key features of the cart-mounted system - (a) three orthogonal transmitters and ten pairs of receivers, and (b) difference or gradient measurements that significantly reduce the ambient and motion noise, and greatly enhance the sensitivity to the gradients of the target. The system characterizes the target from a single position. Results from a local test site were in a good agreement with theoretical performance calculations of such a device. This survey was designed to demonstrate performance of the system under realistic survey conditions at the Aberdeen Proving Ground (APG) in Aberdeen, MD. The survey was preformed in an area with known items ('Calibration Grid'), and in a seeded blind test area (the 'Blind Test Grid'). The ground truth for the surveys conducted on the Blind Test Grid was withheld from the testers. Only the graded test scores based on target detection and target classification were provided. For more information, see http://aec.army.mil/usaec/technology/uxo01c03.html.« less

Relocatable explosives storage magazine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liptak, R.E.; Keenan, W.A.

A relocatable storage magazine apparatus for storing and retrieving explosives and ordnance and for partially containing and attenuating the blast, conflagration and flying debris from an accidental explosion is described comprising: (a) a container having an access hole; (b) a debris trap attached to the container, the debris trap communicating with said container via the access hole, said debris trap having vent holes for venting the pressure of an explosion from said debris trap to the atmosphere; (c) means for covering said access hole; (d) means for suspending explosives and ordnance from the covering means; (e) means for entering themore » storage magazine to store and retrieve explosives and ordnance; (f) means for retaining said covering means in a position above the access hole wherein said explosives and ordnance are accessible from the entering means.« less

Supervised Classification of Underwater Optical Imagery for Improved Detection and Characterization of Underwater Military Munitions

DTIC Science & Technology

2015-06-01

Atmospheric Administration (NOAA) at the “ Ordnance Reef” site off of Waianae, Hawaii by divers using a hand-held high -definition video (HDV) camera...for the Ordnance Reef dataset as well, though less dramatic than the Miami data because the 2-D results were high to begin with at Ordnance Reef...generally > 80% accuracy. Discrimination of environments was high for the major seabed types. For example, sand and mixed sand-seagrass were classified with

Munitions Response Projects Shallow Water Marine UXO Detection Survey - Underwater Survey of Camp Lejeune

DTIC Science & Technology

2011-03-01

following: disturbance of sensitive environments (including wildlife); dredging up potentially contaminated sediments; physical contact with UXO; damaging or...is discussed below. 2.1.1 EM61 System and Sensors The EM61 is a high-resolution time-domain electromagnetic metal detector that is capable of...the position of the tow boat and then try to extrapolate the position of the detector based on cable length and GPS heading. In most cases, the

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record Number 909 (Sky Research, Inc.)

DTIC Science & Technology

2008-09-01

heading north from the southern end point, and then returning south from the northern end point. 2) A metallic pin-flag is placed over the midpoint...test involves traverses across a known point located away from buried UXO or other metallic debris. A 5-meter- length of line is walked in eight...ferrous and nonferrous anomalies. Due to limitations of the magnetometer, the nonferrous items cannot be detected. Therefore, the ROC curves

Standardized UXO Technology Demonstration Site Woods Scoring Record Number 902 (Sky Research, Inc.)

DTIC Science & Technology

2008-08-01

endpoint. 8 2) A metallic pin-flag is placed over the midpoint. 3) The operator logs data along the same path, first traveling north, and then...data and after completion of data collection. This test involves traverses across a known point located away from buried UXO or other metallic ...areas, dips, ruts and obstructions that challenge platform systems or hand held detectors . The challenges include a gravel road, wet areas and trees

Development of a Landmine Detection Sensor Final Report CRADA No. TC02133.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romero, C. E.; Sheppard, C.

2017-09-06

This was one of two CRADAs between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and First Alliance Technologies, LLC (First Alliance), to conduct research and development activity toward an integrated system for the detecting, locating, and destroying of landmines and unexploded ordinance using a laser to destroy landmines and unexploded ordinance and First Alliance’s Land Mine Locator (LML) system. The focus of this CRADA was on developing a sensor system that accurately detects landmines, and provides exact location information in a timely manner with extreme reliability.

View of building 11050 looking southeast. Naval Ordnance Test ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050 looking southeast. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Fire Station & Marine Barracks, D Street, at corner of 4th Street, China Lake, Kern County, CA

63. BUILDING NO. 1301, ORDNANCE FACILITY (MORTAR POWDER BUILDING), INTERIOR, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

63. BUILDING NO. 1301, ORDNANCE FACILITY (MORTAR POWDER BUILDING), INTERIOR, LOOKING SOUTHEAST DOWN SCREENED WALKWAY ON NORTHWEST SIDE. - Picatinny Arsenal, State Route 15 near I-80, Dover, Morris County, NJ

57. BUILDING NO. 1071, ORDNANCE FACILITY (CRYSTALLIZATION BUILDING), LOOKING AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

57. BUILDING NO. 1071, ORDNANCE FACILITY (CRYSTALLIZATION BUILDING), LOOKING AT SOUTHEAST SIDE. NOTE ESCAPE CHUTES PROJECTING FROM SIDES OF BUILDING. - Picatinny Arsenal, State Route 15 near I-80, Dover, Morris County, NJ

Kalman Filters for UXO Detection: Real-Time Feedback and Small Target Detection

DTIC Science & Technology

2012-05-01

last two decades. Accomplishments reported from both hardware and software point of views have moved the re- search focus from simple laboratory tests...quality data which in turn require a good positioning of the sensors atop the UXOs. The data collection protocol is currently based on a two-stage process...Note that this results is merely an illustration of the convergence of the Kalman filter. In practise , the linear part can be directly inverted for if

Advanced UXO Detection and Discrimination Using Magnetic Data Based on Extended Euler Deconvolution and Shape Identification Through Multipole Moments

DTIC Science & Technology

2011-04-01

detection. We also thank Len Pasion and Todd Meglich for helpful discussions on the Camp Sibert data set. Finally, we thank Kris Davis from Colorado...depth of potential UXO using a continuous wavelet transform: Conference proceedings, 1012– 1022, SPIE. Billings, S. D., L. R. Pasion , and D. W...1638 2009 Annual Report. Lanczos, C., 1988, Applied analysis: Courier Dover Publications. Li, Y., Krahenbuhl, R., Meglich, T., Pasion , L

Demonstration Report for Geonics EM-63 Cued-Interrogation Data Collection, Processing and Archiving at Camp Sibert, Alabama

DTIC Science & Technology

2008-08-01

Requirements for UXO Discrimination: Paper prepared for UXO Location Workshop, Annapolis, May 2005. Billings, S. D., Pasion , L. R., Beran, L., Oldenburg, D...Discrimination Strategies for Application to Live Sites. Billings, S. D., Pasion , L. R. and Oldenburg, D., 2007b, Sky Research/University of British Columbia...moved RTS to reacquire SE1-12 which was lost by the DAS issue as well. o Talked with Len Pasion about the best approach for full coverage data given

Ultra-Wideband, Fully Polarimetric Ground Penetrating Radar for UXO Discrimination

DTIC Science & Technology

2007-05-01

principal investigator (PI) was Dr. Kevin O’Neill of ERDC, with the OSU-ESL’s Dr. Chi-Chih Chen as Co-PI. Dr. Chen was at the heart of the project at...provided by Professor Robert Lee of the OSU Department of Electrical Engineering and by his students, including Kishore Rama Rao and Kwan -Ho Lee. Dr...901 North Stuart Street Suite 303 Arlington, VA 22203 703-696-3826 703-696-2114 Anne.Andrews@osd.mil ESTCP UXO Program Manager Dr. Kevin

Standardized UXO Technology Demonstration Site Moguls Scoring Record Number 912 (Sky Research, Inc.)

DTIC Science & Technology

2008-09-01

south from the northern end point. 8 2) A metallic pin-flag is placed over the midpoint. 3) The operator logs data along the same path...buried UXO or other metallic debris. A 5-meter-length of line is walked in eight cardinal directions (N-S, S-N, E-W, W-E, SE-NW, NW-SE, SW-NE, NE-SW...points have been rounded to protect the ground truth. The overall ground truth is composed of ferrous and nonferrous anomalies. Due to limitations

Standardized UXO Technology Demonstration Site Moguls Scoring No. 903 (Sky Research, Inc.)

DTIC Science & Technology

2008-08-01

endpoint, and then returning south from the northern endpoint. 8 2) A metallic pin-flag is placed over the midpoint. 3) The operator logs data...point located away from buried UXO or other metallic debris. A 5-meter-length of line is walked in eight cardinal directions (N-S, S-N, E-W, W-E, SE-NW...systems or handheld detectors . The challenges include a gravel road, wet areas and trees. The vegetation height varies from 15 to 25 cm. Moguls A 1.30

78 FR 22512 - Foreign-Trade Zone (FTZ) 225-Springfield, Missouri; Notification of Proposed Production Activity...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-16

... Board on behalf of General Dynamics Ordnance and Tactical Systems Munitions Services (GDOTS), located in...--Springfield, Missouri; Notification of Proposed Production Activity; General Dynamics Ordnance and Tactical Systems Munitions Services (Demilitarization of Munitions); Carthage, Missouri The City of Springfield...

Integration and Validation of Avian Radars (IVAR)

DTIC Science & Technology

2011-08-01

hazards of electromagnetic radiation to fuel HERO hazards of electromagnetic radiation to ordnance HERP hazards ... hazard Radiation hazard to humans, fuels, and ordnance can be easily managed. Demonstration of how operation of radars can meet hazards of... electromagnetic radiation to personnel (HERP), hazards of electromagnetic radiation to

30. SKETCH OF THE PROPOSED TEST STAND FOR THE ORDNANCE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

30. SKETCH OF THE PROPOSED TEST STAND FOR THE ORDNANCE GUIDED MISSILE CENTER AT REDSTONE ARSENAL (PRE-DATING NASA). JUNE, 1951, HANS LUEHRSEN COLLECTION, MSFC MASTER PLANNING OFFICE. - Marshall Space Flight Center, Saturn Propulsion & Structural Test Facility, East Test Area, Huntsville, Madison County, AL

32 CFR 623.2 - Loan policies.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 2542). (B) For ordnance and ordnance stores loaned to high schools in the District of Columbia (10 U.S...; DACD Plan; Garden Plot Group One: DOD Executive Agent or designee Group One: Arms, ammunition, tank... Bedding, cots, chairs, vehicles, buildings, etc. 11. Civilian Marksmanship Program (Clubs and Schools) 3...

32 CFR 623.2 - Loan policies.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... 2542). (B) For ordnance and ordnance stores loaned to high schools in the District of Columbia (10 U.S...; DACD Plan; Garden Plot Group One: DOD Executive Agent or designee Group One: Arms, ammunition, tank... Bedding, cots, chairs, vehicles, buildings, etc. 11. Civilian Marksmanship Program (Clubs and Schools) 3...

78 FR 48647 - Foreign-Trade Zone 225-Springfield, Missouri; Authorization of Production Activity; General...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-09

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-30-2013] Foreign-Trade Zone 225--Springfield, Missouri; Authorization of Production Activity; General Dynamics Ordnance and Tactical Systems Munitions...-Trade Zones (FTZ) Board on behalf of General Dynamics Ordnance and Tactical Systems Munitions Services...

Reverberant Microwave Propagation

DTIC Science & Technology

2008-10-01

HERO Hazards of Electromagnetic Radiation to Ordnance HP Hewlett Packard HWD Half-Wave Dipole IEC International Electrotechnical Commission IEE...composite panels used in new ship design; Hazards of Electromagnetic Radiation to Ordnance ( HERO ) analyses; and digital wireless system performance...Electro-Explosive Device EMC Electromagnetic Compatibility ft Foot (feet) GHz Gigahertz HERO Hazards of Electromagnetic

Electromagnetic Instrumentation for Exploration and the Environment: A Retrospective Look by Canada's Leading Manufacture

NASA Astrophysics Data System (ADS)

Catalano, M.

2009-05-01

Geonics Limited has a very rich and varied history. This talk will provide a historical perspective about how a few key individuals shaped the development of some of the world's most useful electromagnetic (EM) geophysical instrumentation. A brief review of these systems, including the science behind them, will showcase the evolution of each to the market place and emphasize how a combination of business savvy and a constant investment to research is what lead to a successful line of instrumentation. In 1950 a company called Aeromagnetic Surveys Ltd. was established that was considered "the largest and most diversified air- survey firm in the world" (FLIGHT, 1954), for its time. It employed Vaino Ronka and Alex Herz, young engineers, who patented several new EM technologies including an in-phase and quadrature towed bird helicopter EM system (the first commercial transistorized instrument). The two also set new standards for ground based horizontal loop EM systems and won several mining Blue Ribbon Awards. By the end of 1958, Mr. Ronka began offering independent design services for geophysical instruments and it became inevitable that one day he would form his own company. Geonics Limited was incorporated in 1962 by Vaino Ronka and Alex Herz and the EM-16 VLF receiver, first sold in 1965, became the first successful instrument. It's considered the best selling electrical geophysical tool of all-time and is still sold today by the same model name 44 years later. In 1974, the company was purchased by James Duncan McNeill, the former chief engineering physicist of Barringer Research Ltd. During his time as president of Geonics he was responsible for an explosion of new instruments from the 70's, 80's and into the 90's that permanently placed Geonics instruments in virtually every government environmental lab and consulting firm active in near-surface geophysics. His ability to foresee new problem areas and to define new roles that geophysical methods could play in a solution helped established several key areas of application for Geonics instruments outside of mineral exploration. These included civil engineering, sea-ice thickness and permafrost mapping, environmental site assessment, groundwater exploration, agriculture and archaeology. It is safe to say that without him Geonics would have far fewer geophysical instruments (Kaufman, 1994). Mr. McNeill sold the company to Swedish Geological AB (SGAB), a Swedish government company which also owned ABEM in the early 90's only to purchase it back a year later with new partner Miro Bosnar the VP and chief engineer. Mr. McNeill retired soon after and Geonics has been owned by Mr. Bosnar, the current president and chief engineer, ever since. Mr. Bosnar has been with Geonics since 1968 and has arguably been the most influential person in the history of the company. He has been involved in the design, research and development of every instrument manufactured since that time and has established him self as the most experienced and respected designer of all types of EM systems in the world. From fixed-wing and helicopter towed-bird EM systems to the PROTEM ground transient EM system, ground conductivity meters and a wide variety of metal detectors that have revolutionized the search for unexploded ordnance (UXO) and improvised explosive devices (IED's). EM equipment is generally recognized as one of the most difficult to manufacture but Mr. Bosnar continues to maintain customer loyalty through a strong commitment to research and development and high-quality instruments, including well over 50 commercial products over the last five decades, to an ever-broadening market place.

A Cost-Based Analysis on Using DoD Civilian Workforce to Perform Ordnance Support in Pearl Harbor

DTIC Science & Technology

study examines whether using the government civilian workforce to perform ordnance handling generates cost savings when compared with contracting...Using a cost-based analysis, this study reviews all the associated costs of converting to a government civilian workforce and compares them with the cost

43. BUILDING NO. 454, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. BUILDING NO. 454, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), DETAIL OF EXPLOSION-PROOF ELECTRICAL SWITCH BOX (SWITCH GEAR INSIDE BOX SUBMERGED IN OIL TO QUENCH SPARKS), SWITCH EQUIPMENT MADE BY GENERAL ELECTRIC. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Method for laser machining explosives and ordnance

DOEpatents

Muenchausen, Ross E.; Rivera, Thomas; Sanchez, John A.

2003-05-06

Method for laser machining explosives and related articles. A laser beam is directed at a surface portion of a mass of high explosive to melt and/or vaporize the surface portion while directing a flow of gas at the melted and/or vaporized surface portion. The gas flow sends the melted and/or vaporized explosive away from the charge of explosive that remains. The method also involves splitting the casing of a munition having an encased explosive. The method includes rotating a munition while directing a laser beam to a surface portion of the casing of an article of ordnance. While the beam melts and/or vaporizes the surface portion, a flow of gas directed at the melted and/or vaporized surface portion sends it away from the remaining portion of ordnance. After cutting through the casing, the beam then melts and/or vaporizes portions of the encased explosive and the gas stream sends the melted/vaporized explosive away from the ordnance. The beam is continued until it splits the article, after which the encased explosive, now accessible, can be removed safely for recycle or disposal.

Model based approach to UXO imaging using the time domain electromagnetic method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavely, E.M.

1999-04-01

Time domain electromagnetic (TDEM) sensors have emerged as a field-worthy technology for UXO detection in a variety of geological and environmental settings. This success has been achieved with commercial equipment that was not optimized for UXO detection and discrimination. The TDEM response displays a rich spatial and temporal behavior which is not currently utilized. Therefore, in this paper the author describes a research program for enhancing the effectiveness of the TDEM method for UXO detection and imaging. Fundamental research is required in at least three major areas: (a) model based imaging capability i.e. the forward and inverse problem, (b) detectormore » modeling and instrument design, and (c) target recognition and discrimination algorithms. These research problems are coupled and demand a unified treatment. For example: (1) the inverse solution depends on solution of the forward problem and knowledge of the instrument response; (2) instrument design with improved diagnostic power requires forward and inverse modeling capability; and (3) improved target recognition algorithms (such as neural nets) must be trained with data collected from the new instrument and with synthetic data computed using the forward model. Further, the design of the appropriate input and output layers of the net will be informed by the results of the forward and inverse modeling. A more fully developed model of the TDEM response would enable the joint inversion of data collected from multiple sensors (e.g., TDEM sensors and magnetometers). Finally, the author suggests that a complementary approach to joint inversions is the statistical recombination of data using principal component analysis. The decomposition into principal components is useful since the first principal component contains those features that are most strongly correlated from image to image.« less

23. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), INTERIOR, LOOKING SOUTH DOWN CENTRAL CORRIDOR. NOTE BINS IN WALLS ON EITHER SIDE OF CORRIDOR, USED FOR PASSING EXPLOSIVES AND LOADED ITEMS TO SIEVING ROOMS BEYOND WALLS. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

62. BUILDING NO. 1301, ORDNANCE FACILITY (MORTAR POWDER BUILDING), LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

62. BUILDING NO. 1301, ORDNANCE FACILITY (MORTAR POWDER BUILDING), LOOKING AT NORTHWEST FACADE. ACCESS TO ROOF ALLOWS MAINTENANCE OF VENTILATION EQUIPMENT WHICH IS PLACED OUTSIDE BUILDING TO MINIMIZE EXPLOSION HAZARD. NO. 2 VISIBLE ON WALL OF BUILDING STANDS FOR EXPLOSION HAZARD WITH FRAGMENTATION. - Picatinny Arsenal, State Route 15 near I-80, Dover, Morris County, NJ

A rail system for circular synthetic aperture sonar imaging and acoustic target strength measurements: design/operation/preliminary results.

PubMed

Kennedy, J L; Marston, T M; Lee, K; Lopes, J L; Lim, R

2014-01-01

A 22 m diameter circular rail, outfitted with a mobile sonar tower trolley, was designed, fabricated, instrumented with underwater acoustic transducers, and assembled on a 1.5 m thick sand layer at the bottom of a large freshwater pool to carry out sonar design and target scattering response studies. The mobile sonar tower translates along the rail via a drive motor controlled by customized LabVIEW software. The rail system is modular and assembly consists of separately deploying eight circular arc sections, measuring a nominal center radius of 11 m and 8.64 m arc length each, and having divers connect them together in the underwater environment. The system enables full scale measurements on targets of interest with 0.1° angular resolution over a complete 360° aperture, without disrupting target setup, and affording a level of control over target environment conditions and noise sources unachievable in standard field measurements. In recent use, the mobile cart carrying an instrumented sonar tower was translated along the rail in 720 equal position increments and acoustic backscatter data were acquired at each position. In addition, this system can accommodate both broadband monostatic and bistatic scattering measurements on targets of interest, allowing capture of target signature phenomena under diverse configurations to address current scientific and technical issues encountered in mine countermeasure and unexploded ordnance applications. In the work discussed here, the circular rail apparatus is used for acoustic backscatter testing, but this system also has the capacity to facilitate the acquisition of magnetic and optical sensor data from targets of interest. A brief description of the system design and operation will be presented along with preliminary processed results for data acquired from acoustic measurements conducted at the Naval Surface Warfare Center, Panama City Division Test Pond Facility. [Work Supported by the U.S. Office of Naval Research and The Strategic Environmental Research and Development Program.].

Uncertainty quantification of seabed parameters for large data volumes along survey tracks with a tempered particle filter

NASA Astrophysics Data System (ADS)

Dettmer, J.; Quijano, J. E.; Dosso, S. E.; Holland, C. W.; Mandolesi, E.

2016-12-01

Geophysical seabed properties are important for the detection and classification of unexploded ordnance. However, current surveying methods such as vertical seismic profiling, coring, or inversion are of limited use when surveying large areas with high spatial sampling density. We consider surveys based on a source and receiver array towed by an autonomous vehicle which produce large volumes of seabed reflectivity data that contain unprecedented and detailed seabed information. The data are analyzed with a particle filter, which requires efficient reflection-coefficient computation, efficient inversion algorithms and efficient use of computer resources. The filter quantifies information content of multiple sequential data sets by considering results from previous data along the survey track to inform the importance sampling at the current point. Challenges arise from environmental changes along the track where the number of sediment layers and their properties change. This is addressed by a trans-dimensional model in the filter which allows layering complexity to change along a track. Efficiency is improved by likelihood tempering of various particle subsets and including exchange moves (parallel tempering). The filter is implemented on a hybrid computer that combines central processing units (CPUs) and graphics processing units (GPUs) to exploit three levels of parallelism: (1) fine-grained parallel computation of spherical reflection coefficients with a GPU implementation of Levin integration; (2) updating particles by concurrent CPU processes which exchange information using automatic load balancing (coarse grained parallelism); (3) overlapping CPU-GPU communication (a major bottleneck) with GPU computation by staggering CPU access to the multiple GPUs. The algorithm is applied to spherical reflection coefficients for data sets along a 14-km track on the Malta Plateau, Mediterranean Sea. We demonstrate substantial efficiency gains over previous methods. [This research was supported in part by the U.S. Dept of Defense, thought the Strategic Environmental Research and Development Program (SERDP).

Optimization of ground-water withdrawal at the old O-Field area, Aberdeen Proving Ground, Maryland

USGS Publications Warehouse

Banks, William S.L.; Dillow, Jonathan J.A.

2001-01-01

The U.S. Army disposed of chemical agents, laboratory materials, and unexploded ordnance at the Old O-Field landfill at Aberdeen Proving Ground, Maryland, beginning prior to World War II and continuing until at least the 1950?s. Soil, ground water, surface water, and wetland sediments in the Old O-Field area were contaminated by the disposal of these materials. The site is in the Atlantic Coastal Plain, and is characterized by a complex series of Pleistocene and Holocene sediments formed in various fluvial, estuarine, and marine-marginal hydrogeologic environments. A previously constructed transient finite-difference ground-water-flow model was used to simulate ground-water flow and the effects of a pump-and-treat remediation system designed to prevent contaminated ground water from flowing into Watson Creek (a tidal estuary and a tributary to the Gunpowder River). The remediation system consists of 14 extraction wells located between the Old O-Field landfill and Watson Creek.Linear programming techniques were applied to the results of the flow-model simulations to identify optimal pumping strategies for the remediation system. The optimal management objective is to minimize total withdrawal from the water-table aquifer, while adhering to the following constraints: (1) ground-water flow from the landfill should be prevented from reaching Watson Creek, (2) no extraction pump should be operated at a rate that exceeds its capacity, and (3) no extraction pump should be operated at a rate below its minimum capacity, the minimum rate at which an Old O-Field pump can function. Water withdrawal is minimized by varying the rate and frequency of pumping at each of the 14 extraction wells over time. This minimizes the costs of both pumping and water treatment, thus providing the least-cost remediation alternative while simultaneously meeting all operating constraints.The optimal strategy identified using this objective and constraint set involved operating 13 of the 14 extraction wells at rates ranging from 0.4 to 4.9 gallons per minute.

A rail system for circular synthetic aperture sonar imaging and acoustic target strength measurements: Design/operation/preliminary results

NASA Astrophysics Data System (ADS)

Kennedy, J. L.; Marston, T. M.; Lee, K.; Lopes, J. L.; Lim, R.

2014-01-01

A 22 m diameter circular rail, outfitted with a mobile sonar tower trolley, was designed, fabricated, instrumented with underwater acoustic transducers, and assembled on a 1.5 m thick sand layer at the bottom of a large freshwater pool to carry out sonar design and target scattering response studies. The mobile sonar tower translates along the rail via a drive motor controlled by customized LabVIEW software. The rail system is modular and assembly consists of separately deploying eight circular arc sections, measuring a nominal center radius of 11 m and 8.64 m arc length each, and having divers connect them together in the underwater environment. The system enables full scale measurements on targets of interest with 0.1° angular resolution over a complete 360° aperture, without disrupting target setup, and affording a level of control over target environment conditions and noise sources unachievable in standard field measurements. In recent use, the mobile cart carrying an instrumented sonar tower was translated along the rail in 720 equal position increments and acoustic backscatter data were acquired at each position. In addition, this system can accommodate both broadband monostatic and bistatic scattering measurements on targets of interest, allowing capture of target signature phenomena under diverse configurations to address current scientific and technical issues encountered in mine countermeasure and unexploded ordnance applications. In the work discussed here, the circular rail apparatus is used for acoustic backscatter testing, but this system also has the capacity to facilitate the acquisition of magnetic and optical sensor data from targets of interest. A brief description of the system design and operation will be presented along with preliminary processed results for data acquired from acoustic measurements conducted at the Naval Surface Warfare Center, Panama City Division Test Pond Facility. [Work Supported by the U.S. Office of Naval Research and The Strategic Environmental Research and Development Program.

Hand-held UXO Discriminator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, E.; Smith, J.T.; Kappler, K.N.

2010-04-01

With prior funding (UX-1225, MM-0437, and MM-0838), we have successfully designed and built a cart-mounted Berkeley UXO Discriminator (BUD) and demonstrated its performance at various test sites (e.g., Gasperikova et al., 2007, 2009). It is a multi-transmitter multi-receiver active electromagnetic system that is able to discriminate UXO from scrap at a single measurement position, hence eliminates equirement of a very accurate sensor location. The cart-mounted system comprises of three orthogonal transmitters and eight pairs of differenced receivers (Smith et al., 2007). Receiver coils are located on ymmetry lines through the center of the system and see identical fields during themore » on-time of the pulse in all of the transmitter coils. They can then be wired in opposition to produce zero output during the n-ime of the pulses in three orthogonal transmitters. Moreover, this configuration dramatically reduces noise in the measurements by canceling the background electromagnetic fields (these fields are uniform ver the scale of the receiver array and are consequently nulled by the differencing operation), and by canceling the noise contributed by the tilt of the receivers in the Earth's magnetic field, and therefore reatly enhances receivers sensitivity to the gradients of the target.« less

44 CFR 312.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... property or persons in the United States in any manner by sabotage or by use of bombs, shellfire, or atomic... special weapons; unexploded bomb reconnaissance; essential debris clearance; emergency welfare measures...

44 CFR 312.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... property or persons in the United States in any manner by sabotage or by use of bombs, shellfire, or atomic... special weapons; unexploded bomb reconnaissance; essential debris clearance; emergency welfare measures...

Overview to the north from near ordnance warehouse A199, showing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Overview to the north from near ordnance warehouse A-199, showing water tank 188-A, 188-B behind, magazine A-211 at center, and magazine A-212 at far right. The city of Vallejo is in the distance. - Mare Island Naval Shipyard, Fresh Water Tanks, East of Mesa Road & north of Kieper Road, Vallejo, Solano County, CA

77 FR 87 - Taking of Marine Mammals Incidental to Specified Activities; U.S. Marine Corps Training Exercises...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-03

... ordnances proposed for use at BT-9 and BT- 11 include small arms, large arms, bombs, rockets, missiles, and... number of takes for all types of ordnance (including practice bombs and 25-mm live rounds). Response... error; high explosive rounds planned for use by USMC include only 30- and 40-mm rounds. Practice bombs...

33 CFR 334.920 - Pacific Ocean off the east coast of San Clemente Island, Calif.; naval restricted area.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of San Clemente Island, Calif.; naval restricted area. 334.920 Section 334.920 Navigation and... RESTRICTED AREA REGULATIONS § 334.920 Pacific Ocean off the east coast of San Clemente Island, Calif.; naval... vessels, other than Naval Ordnance Test Station craft, and those cleared for entry by the Naval Ordnance...

Energy Engineering Analysis Program, limited energy study of steam distribution systems, Hawthorne Army Ammunition Depot, Hawthorne, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-12-31

This report summarizes all work of the Limited Energy Study of Steam Distribution Systems, Energy Engineering Analysis Program, Hawthorne Army Ammunition Depot (HWAAD), Nevada. The project is authorized under Contract No. DACA05-92-C-0155 with the U.S. Army Corps of Engineers, Sacramento District, California. The purpose of this limited energy study is to evaluate steam distribution and condensate collection systems in both the Industrial Area and Ordnance Area of HWAAD to develop a set of replacement actions that will reduce energy consumption and operating costs. These efforts consist of corrections and revisions to previously submitted funding requests. Amended DD Forms 1391 andmore » supporting documentation are prepared for: (1) Project 40667, Modernize Steam Distribution System, Industrial Area, and (2) Project 42166, Modernize Ordnance Area Steam Distribution, Ordnance Area. HWAAD is located next to Highway 95 near the center of Nevada`s border with California, about 130 miles southeast of Reno. The elevation is about 4,100 feet. The location is depicted on Figure 1-1. A number of facilities covering over 140,000 acres constitute HWAAD; however, this study was limited to the Industrial and Ordnance Areas.« less

Haptics-based immersive telerobotic system for improvised explosive device disposal: Are two hands better than one?

NASA Astrophysics Data System (ADS)

Erickson, David; Lacheray, Hervé; Lambert, Jason Michel; Mantegh, Iraj; Crymble, Derry; Daly, John; Zhao, Yan

2012-06-01

State-of-the-art robotic explosive ordnance disposal robotics have not, in general, adopted recent advances in control technology and man-machine interfaces and lag many years behind academia. This paper describes the Haptics-based Immersive Telerobotic System project investigating an immersive telepresence envrionment incorporating advanced vehicle control systems, Augmented immersive sensory feedback, dynamic 3D visual information, and haptic feedback for explosive ordnance disposal operators. The project aim is to provide operatiors a more sophisticated interface and expand sensory input to perform complex tasks to defeat improvised explosive devices successfully. The introduction of haptics and immersive teleprescence has the potential to shift the way teleprescence systems work for explosive ordnance disposal tasks or more widely for first responders scenarios involving remote unmanned ground vehicles.

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), INTERIOR VIEW LOOKING WEST AT NORTH END OF CENTRAL CORRIDOR (ROOM 3). STAIRWAY WORKBENCH WITH COMPRESSED-AIR POWERED CARTRIDGE LOADER. ARMORED PASS-THROUGH OF TRANSFER BOX FOR PASSING EXPLOSIVES MATERIALS THROUGH TO NEXT ROOM TO THE NORTH. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Spectrum Management and Electromagnetic Environmental Effects (E3) Business Process

DTIC Science & Technology

2010-05-06

HAZARDS OF ELECTROMAGNETIC RADIATION TO ORDNANCE ( HERO ) SURVEY. XM11: IS THERE A CURRENT ELECTROMAGNETIC INTERFERENCE (EMI) SITE SURVEY. SM & EMI Navy...PERSONNEL (HERP) / FUEL (HERF) SURVEY. XM10: IS THERE A CURRENT HAZARDS OF ELECTROMAGNETIC RADIATION TO ORDNANCE ( HERO ) SURVEY. XM11...OF ALL KNOWN ELECTROMAGNETIC INTERFERENCE (EMI) FIXES INSTALLED ONE YEAR AFTER SURVEY COMPLETION. M05: OF ALL RADIATION HAZARDS

Final Environmental Assessment for the Joint Integrated Fires Exercise at Avon Park Air Force Range, Florida

DTIC Science & Technology

2005-04-01

Tactical Operations Center TRI-DDS................ Toxic Release Inventory Data Delivery System US...Emissions from ordnance are tracked by the Toxic Release Inventory Data Delivery System (TRI-DDS) (URS 2001). Emission releases by ordnance at...listed threatened plant (pigeonwing) and one federally listed endangered plant (hairy jointweed or wireweed ) are known to occur on APAFR. Surveys have

The application of measurement techniques to track flutter testing

NASA Technical Reports Server (NTRS)

Roglin, H. R.

1975-01-01

The application is discussed of measurement techniques to captive flight flutter tests at the Supersonic Naval Ordnance Research Track (SNORT), U. S. Naval Ordnance Test Station, China Lake, California. The high-speed track, by its ability to prove the validity of design and to accurately determine the actual margin of safety, offers a unique method of flutter testing for the aircraft design engineer.

Risk factors for injuries in the U.S. Army Ordnance School.

PubMed

Grier, Tyson L; Morrison, Stephanie; Knapik, Joseph J; Canham-Chervak, Michelle; Jones, Bruce H

2011-11-01

To investigate risk factors for time-loss injuries among soldiers attending U.S. Army Ordnance School Advanced Individual Training. Injuries were obtained from an injury surveillance system. A health questionnaire provided data on age, race, rank, current self-reported injury and illness, and tobacco use. Fitness data was obtained from operations office. Cumulative time-loss injury incidence was 31% for men and 54% for women. For men, higher risk of injury was associated with race, a current self-reported injury, smoking before entering the Army, lower sit-up performance, and slower 2-mile run times. For women, higher risk of injury was associated with race, a current self-reported injury, and slower 2-mile run times. Smoking cessation and fitness training before entry are potential strategies to reduce injuries among soldiers in the Ordnance School.

Identifying Minefields and Verifying Clearance: Adapting Statistical Methods for UXO Target Detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Richard O.; O'Brien, Robert F.; Wilson, John E.

2003-09-01

It may not be feasible to completely survey large tracts of land suspected of containing minefields. It is desirable to develop a characterization protocol that will confidently identify minefields within these large land tracts if they exist. Naturally, surveying areas of greatest concern and most likely locations would be necessary but will not provide the needed confidence that an unknown minefield had not eluded detection. Once minefields are detected, methods are needed to bound the area that will require detailed mine detection surveys. The US Department of Defense Strategic Environmental Research and Development Program (SERDP) is sponsoring the development ofmore » statistical survey methods and tools for detecting potential UXO targets. These methods may be directly applicable to demining efforts. Statistical methods are employed to determine the optimal geophysical survey transect spacing to have confidence of detecting target areas of a critical size, shape, and anomaly density. Other methods under development determine the proportion of a land area that must be surveyed to confidently conclude that there are no UXO present. Adaptive sampling schemes are also being developed as an approach for bounding the target areas. These methods and tools will be presented and the status of relevant research in this area will be discussed.« less

Catalog of Nonresident Training Courses, 1994 Edition

DTIC Science & Technology

1994-01-01

0:- 0000 1,0000 � I 0Ŕ 񓀠 Gmo ~a) : 0000 -0000 "� apIeum".0000 񓀠 񓀠 : 0000 ൈ ŕ,0000 MAIING ~I- � 񓀠 :Gomm0 0000~ no000...administration hardware; aircraft power plants ; aircraft avionics; aircraft and training; aviation safety; operations and exercises; and ordnance...construction; classified CONFIDENTIAL. aircraft hardware; aircraft power plants ; aircraft avionics; aircraft ordnance; support equipment and line operations; SEE

Department of the Navy Explosives Safety Site Approval Process Improvement Initiative

DTIC Science & Technology

2010-07-01

All applicable existing land-use restrictions, such as explosives safety quantity distance (ESQD) arcs, Hazards of Electromagnetic Radiation to... Ordnance ( HERO ) zones, air field safety zones, and munitions response program sites are noted in the ESAR.  PWO will have in place a written...N547) Naval Ordnance Safety and Security Activity Farragut Hall, 3817 Strauss Ave, Suite 108 Indian Head, MD 20640-5151 (301) 744-6059

Development of marine toxicity data for ordnance compounds

USGS Publications Warehouse

Nipper, M.; Carr, R.S.; Biedenbach, J.M.; Hooten, R.L.; Miller, K.; Saepoff, S.

2001-01-01

A toxicity database for ordnance compounds was generated using eight compounds of concern and marine toxicity tests with five species from different phyla. Toxicity tests and endpoints included fertilization success and embryological development with the sea urchin Arbacia punctulata; zoospore germination, germling length, and cell number with the green macroalga Ulva fasciata; survival and reproductive success of the polychaete Dinophilus gyrociliatus; larvae hatching and survival with the redfish Sciaenops ocellatus; and survival of juveniles of the opossum shrimp Americamysis bahia (formerly Mysidopsis bahia). The studied ordnance compounds were 2,4- and 2,6-dinitrotoluene, 2,4,6-trinitrotoluene, 1,3-dinitrobenzene, 1,3,5-trinitrobenzene, 2,4,6-trinitrophenylmethylnitramine (tetryl), 2,4,6-trinitrophenol (picric acid), and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). The most sensitive toxicity test endpoints overall were the macroalga zoospore germination and the polychaete reproduction tests. The most toxic ordnance compounds overall were tetryl and 1,3,5-trinitrobenzene. These were also the most degradable compounds, often being reduced to very low or below-detection levels at the end of the test exposure. Among the dinitro- and trinitrotoluenes and benzenes, toxicity tended to increase with the level of nitrogenation. Picric acid and RDX were the least toxic chemicals tested overall.

Upper Atmosphere Research Report Number 2

DTIC Science & Technology

1946-12-30

Laboratory personnel working under the direction 0-@. of U. S . Armj Ordnance and General Electric Company personnel. 45. *6 A", ., . . . . __V s ;... r.r.r...thanks are due to U. S . Army ordnance and General Electric Company person- nel for making the fin installation possible and for aid in recovering the...CONDUCTED IN THE-V-2 •....... . . . . . . A. Solar Spectroscopy - F. S . Johnson, J. J. Oberly, C. V. Strain and Re Tousey........ 44 1. Introduction

Source Hierarchy List. Volume 3. O through Z

DTIC Science & Technology

1994-07-01

NAVAL WEAPONS CENTER CHINA LAKE CA MARINE AVIATION DETACHMENT* 07 NAVAL WEAPONS CENTER CORONA ANNEX CA 08 NAVAL ORDNANCE LAB CORONA CA 08 NAVAL...WEAPONS CENTER CORONA LABS CA 05 NAVAL AIR WEAPONS STATION CHINA LAKE CA 05 PACIFIC MISSILE TEST CENTER POINT MUGU CA 06 AIR DEVELOPMENT SQUADRON FOUR...INDIAN HEAD MD 03 NAVAL ORDNANCE CENTER INDIAN HEAD MO 04 NAVAL WARFARE ASSESSMENT CENTER CORONA CA 05 FLEET ANALYSIS CENTER CORONA CA 03

77 FR 1500 - Plum Tree Island National Wildlife Refuge, Poquoson, VA

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-10

... but the refuge's 200-acre Cow Island Tract as a gunnery and bombing range. Extensive unexploded... access. The only public use offered is an annual, permit-only, waterfowl hunt on the Cow Island Tract...

Photocopy of plan (in U.S. Army office of Army Engineers ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of plan (in U.S. Army office of Army Engineers plans and drawings, Fort Hancock and Sandy hook proving ground, record group 7, drawer 44, Cartographic and Architectural branc, The National Archives, Washington, DC) , Ordnance Dept. U.S. Army, proposed addition to dock at Sandy Hook, 1918 Ordnance wharf and boathouse - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

Confederate Staff Work At Chickamauga: An Analysis of the Staff of the Army of Tennessee.

DTIC Science & Technology

1992-06-05

Strategy: from Machiavelli to the Nuclear Age, Peter Paret, ed., (Princeton: Princeton University Press, 1986), 143-185, presents an excellent summary...Lieut. P. B. Spence Asst. Inspector General Lieut. John Rawle Acting Chief of Ordnance Capt Felix H. Robertson Acting Chief of Artillery Maj. J. J...F. Sevier Asst. Inspector General Lieut. P. B. Spence Asst. Inspector General Lieut. John Rawle Acting Chief of Ordnance Lt. Col. Marshall T. Polk

Ammonia Oxidation Plant at Plum Brook Ordnance Works

NASA Image and Video Library

1943-06-21

An ammonia oxidation plant at the Plum Brook Ordnance Works near Sandusky, Ohio, which later became the National Aeronautics and Space Administration’s (NASA) Plum Brook Station. During World War II the ordnance works produced trinitroluene (TNT), dinitrotoluene (DNT), and pentolite which were crated and shipped to an arsenal in Ravenna, Ohio. There, the explosives were packed into shells and sent to Allied forces overseas. Plum Brook was the third largest producer of TNT during World War II. Toluene, sulfuric acid, and nitric acid were used to manufacture the TNT. Nitric Acid is made by oxidizing ammonia, adding water, and concentrating it. The facility in this photograph was used for this oxidation. The structure included air compressors, filters, aftercoolers, power recovery systems, air receivers, heaters, ammonia gasifiers, gas mixers, cooler condensers, absorption columns, and bleaching columns. The Plum Brook Ordnance Works was shut down immediately after the war and remained vacant for the next ten years. NASA’s predecessor, the National Advisory Committee for Aeronautics (NACA), acquired the 500 acres of the site in 1955 to build a nuclear test reactor. By 1963, the agency had acquired the entire 9000 acres from the Army. Almost all of the military facilities were removed in the early 1960s. Plum Brook Station contained over 30 test facilities at its peak in the late 1960s. Today there are four major facilities in operation.

EMI Array for Cued UXO Discrimination ESTCP MM-0601 Demonstration Data Report. APG Standardized UXO Test Site

DTIC Science & Technology

2010-01-14

30 cm above the ground. The sensor boom is designed to pivot up to protect the sensors from damage due to impact with obstructions. This degree of...day for immediate use for background subtraction and future analysis regarding issues of background variability and the impact on fit parameter...I13 H13 G13 F13 E13 D13 C13 B13 A13 T12 S12 R12 Q12 P12 O12 N12 M12 L12 K12 J12 I12 H12 G12 F12 E12 D12 C12 B12 A12 T11 S11 R11 Q11 P11 O11 N11 M11

40. BUILDING NO. 454, ORDNANCE FACILITY (BAG CHANGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. BUILDING NO. 454, ORDNANCE FACILITY (BAG CHANGE FILLING PLANT), DETAIL SOUTHEAST SIDE OF EXTERIOR ELECTRICAL EQUIPMENT ROOM, SHOWING DOOR TO SEWING ROOM NO. 3, VENTILATOR FAN (OVER DOOR), STEAM LINE (PIPE), SEWING MACHINE MOTOR IN OVERHEAD, ALARM BELL, EXPLOSION-PROOF SWITCH BOXES, GROUNDS ON DOORS, PULL ALARM HANDLE (EXTREME RIGHT; PULLEY CABLE CONDUCTED IN CONDUIT TO SWITCH INSIDE BUILDING. PULLEYS INSIDE ALL ELBOW JOINTS.) - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Minutes of the Explosives Safety Seminar (25th) Held in Anaheim, California on 18-20 August 1992. Volume 3

DTIC Science & Technology

1992-08-20

the potential health and safety effects posed by the hazardous waste and ordnance at the site. When the COE began our studies, the media began to...all with the contamination can still be affected through the food chain. This is not true for OEW. The population at risk is effectively limited to...a serious health hazard. The effects of ordnance and explosive waste exposures are much more immediate, and easier to measure. Most of the time

Submarine Hydraulic Fluid Explosion Mitigation and Fire Threats to Ordnance

DTIC Science & Technology

2005-01-18

capable of absorbing large amounts of energy from a developing explosion if the mist can be delivered, in sufficient quantity, to the point of origin of...doors (H8, H13 , H14, D10, D11, SI and S2 in Figure 1) during the explosion tests. In addition, the frame bay ducts that connect 3 the torpedo room and...appreciable impact on the overpressure, explosion tests were run with and without the dummy ordnance. Two replicate tests of each configuration were conducted

Balancing cross-sections combining field work and remote sensing data using LithoTect software in the Zagros fold-and-thrust belt, N Iraq.

NASA Astrophysics Data System (ADS)

Reif, Daniel; Grasemann, Bernhard; Lockhart, Duncan

2010-05-01

The Zagros fold-and-thrust belt has formed in detached Phanerozoic sedimentary cover rocks above a shortened crystalline Precambrian basement and evolved through the Late Cretaceous to Miocene collision between the Arabian and Eurasian plate, during which the Neotethys oceanic basin was closed. Deformation is partitioned in SW directed folding and thrusting of the sediments and NW-SE to N-S trending dextral strike slip faults. The sub-cylindrical doubly-plunging fold trains with wavelengths of 5 - 10 km host more than half of the world's hydrocarbon reserves in mostly anticlinal traps. Generally the Zagros is divided into three NW-SE striking tectonic units: the Zagros Imbricate Zone, the Zagros Simply Folded Belt and the Zagros Foredeep. This work presents a balanced cross-section through the Simply Folded Belt, NE of the city of Erbil (Kurdistan, Iraq). The regional stratigraphy comprises mainly Cretaceous to Cenozoic folded sediments consisting of massive, carbonate rocks (limestones, dolomites), reacting as competent layers during folding compared to the incompetent behavior of interlayered siltstones, claystones and marls. Although the overall security situation in Kurdistan is much better than in the rest of Iraq, structural field mapping was restricted to asphalt streets, mainly because of the contamination of the area with landmines and unexploded ordnance. In order to extend the structural measurements statistically over the investigated area, we used a newly developed software tool (www.terramath.com) for interactive structural mapping of spatial orientations (i.e. dip direction and dip angles) of the sedimentary beddings from digital elevation models. Structural field data and computed measurements where integrated and projected in NE-SW striking balanced cross-sections perpendicular to the regional trend of the fold axes. We used the software LithoTect (www.geologicsystems.com) for the restoration of the cross-sections. Depending on the interpretation of the shape of the synclines, which are not exposed and covered by Neogene sediments, the shortening is in the order of 10-20%. The restoration confirms that large scale faulting is only of minor importance in the Simply Folded Belt.

2017 Global Explosive Ordnance Disposal (EOD) Symposium and Exhibition. Held in North Bethesda, MD on 8-9 August 2017.

DTIC Science & Technology

2017-08-09

Commander, Israeli National Police Bomb Squad, Senior CIED Analyst & Author, Mobius Reports 9:00 AM - 6:30 PM Exhibit Hall Open Salons A-E 9:30 AM...Operation Inherent Resolve • COL Frank Davis, USA, Commander, 71st EOD Group 9:00 AM - 9:45 AM Belgium Bombing of 22 March 2016 Briefing • Commander...SYNEXXUS 201 United States Bomb Technician Association 202 55th Ordnance Company (EOD) 203 RE2 Robotics 204 W.S. Darley & Company 207 Roboteam Inc. 210

32 CFR 179.7 - Sequencing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and social factors. (3) Economic factors, including economic considerations pertaining to... maintenance; alternatives to removal or treatment of contamination when existing technology cannot achieve... availability of appropriate technology (e.g., technology to detect, discriminate, recover, and destroy UXO...

32 CFR 179.7 - Sequencing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and social factors. (3) Economic factors, including economic considerations pertaining to... maintenance; alternatives to removal or treatment of contamination when existing technology cannot achieve... availability of appropriate technology (e.g., technology to detect, discriminate, recover, and destroy UXO...

32 CFR 179.7 - Sequencing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and social factors. (3) Economic factors, including economic considerations pertaining to... maintenance; alternatives to removal or treatment of contamination when existing technology cannot achieve... availability of appropriate technology (e.g., technology to detect, discriminate, recover, and destroy UXO...

Proposed system safety design and test requirements for the microlaser ordnance system

NASA Technical Reports Server (NTRS)

Stoltz, Barb A.; Waldo, Dale F.

1993-01-01

Safety for pyrotechnic ignition systems is becoming a major concern for the military. In the past twenty years, stray electromagnetic fields have steadily increased during peacetime training missions and have dramatically increased during battlefield missions. Almost all of the ordnance systems in use today depend on an electrical bridgewire for ignition. Unfortunately, the bridgewire is the cause of the majority of failure modes. The common failure modes include the following: broken bridgewires; transient RF power, which induces bridgewire heating; and cold temperatures, which contracts the explosive mix away from the bridgewire. Finding solutions for these failure modes is driving the costs of pyrotechnic systems up. For example, analyses are performed to verify that the system in the environment will not see more energy than 20 dB below the 'No-fire' level. Range surveys are performed to determine the operational, storage, and transportation RF environments. Cryogenic tests are performed to verify the bridgewire to mix interface. System requirements call for 'last minute installation,' 'continuity checks after installation,' and rotating safety devices to 'interrupt the explosive train.' As an alternative, MDESC has developed a new approach based upon our enabling laser diode technology. We believe that Microlaser initiated ordnance offers a unique solution to the bridgewire safety concerns. For this presentation, we will address, from a system safety viewpoint, the safety design and the test requirements for a Microlaser ordnance system. We will also review how this system could be compliant to MIL-STD-1576 and DOD-83578A and the additional necessary requirements.

A multisensor system for detection and characterization of UXO(MM-0437) - Demonstration Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasperikova, Erika; Smith, J.T.; Morrison, H.F.

2006-06-01

The Berkeley UXO discriminator (BUD) (Figure 1) is a portable Active Electromagnetic (AEM) system for UXO detection and characterization that quickly determines the location, size, and symmetry properties of a suspected UXO. The BUD comprises of three orthogonal transmitters that 'illuminate' a target with fields in three independent directions in order to stimulate the three polarization modes that, in general, characterize the target EM response. In addition, the BUD uses eight pairs of differenced receivers for response recording. Eight receiver coils are placed horizontally along the two diagonals of the upper and lower planes of the two horizontal transmitter loops.more » These receiver coil pairs are located on symmetry lines through the center of the system and each pair sees identical fields during the on-time of the pulse in all of the transmitter coils. They are wired in opposition to produce zero output during the on-time of the pulses in three orthogonal transmitters. Moreover, this configuration dramatically reduces noise in the measurements by canceling the background electromagnetic fields (these fields are uniform over the scale of the receiver array and are consequently nulled by the differencing operation), and by canceling the noise contributed by the tilt of the receivers in the Earth's magnetic field, and greatly enhances receivers sensitivity to the gradients of the target response. The BUD performs target characterization from a single position of the sensor platform above a target. BUD was designed to detect and characterize UXO in the 20 mm to 155 mm size range for depths between 0 and 1 m. The relationship between the object size and the depth at which it can be detected is illustrated in Figure 2. This curve was calculated for BUD assuming that the receiver plane is 20 cm above the ground. Figure 2 shows that, for example, BUD can detect and characterize an object with 10 cm diameter down to the depth of 90 cm with depth uncertainty of 10%. Any objects buried at the depth more than 1 m have a low probability of detection. With existing algorithms in the system computer it is not possible to recover the principal polarizabilities of large objects close to the system. Detection of large shallow objects is assured, but at present real time discrimination for shallow objects is not. Post processing of the field data is required for shape discrimination of large shallow targets. Next generation of BUD software will not have this limitation. Successful application of the inversion algorithm that solves for the target parameters is contingent upon resolution of this limitation. At the moment, interpretation software is developed for a single object only. In case of multiple objects the software indicates the presence of a cluster of objects but is unable to provide characteristics of each individual object.« less

High Density LiDAR and Orthophotography in UXO Wide Area Assessment

DTIC Science & Technology

2008-01-01

4 Figure 2. Helicopter-Mounted LiDAR and Orthophoto Sensor Equipment...4 Figure 3. LiDAR and Orthophoto System Installed on Helicopter........................................ 6 Figure 4. Kirtland Precision...17 Figure 11. Orthophoto Data Density Results

Maintenance Categories - A Substudy of the Maintenance Support Structure for Contingency Forces Study (ACN 21012).

DTIC Science & Technology

1977-06-23

ORDNANCE AND CHEMICAL CENTEER AND SCHOOL CL.. TAA t ~ 4L . ? LtIITED STATES ARMY ORDNANCE AND CHEM4ICAL CENTER AND SCHOOLJ ABERDEEN PROVING GlRUND, MD 21005...isUNCLASSIFIED. DISTRIBUTIONTTh • maw•F • t ~ istr’ e .•only with fS Army a ii ° ! ACKNOWLEDGEMENT This studxy was initiated and sponsored by the US Army...MAC charts, and if MAC charts corrected throughI compliance with this policy were to supersede current charts. xiX ik" ""I s ,. * t .. . . •._ • , - 4

SAR studies in the Yuma Desert, Arizona: Sand penetration, geology, and the detection of military ordnance debris

USGS Publications Warehouse

Schaber, G.G.

1999-01-01

Synthetic Aperture Radar (SAR) images acquired over part of the Yuma Desert in southwestern Arizona demonstrate the ability of C-band (5.7-cm wavelength), L-band (24.5 cm), and P-band (68 cm) AIRSAR signals to backscatter from increasingly greater depths reaching several meters in blow sand and sandy alluvium. AIRSAR images obtained within the Barry M. Goldwater Bombing and Gunnery Range near Yuma, Arizona, show a total reversal of C- and P-band backscatter contrast (image tone) for three distinct geologic units. This phenomenon results from an increasingly greater depth of radar imaging with increasing radar wavelength. In the case of sandy- and small pebble-alluvium surfaces mantled by up to several meters of blow sand, backscatter increases directly with SAR wavelength as a result of volume scattering from a calcic soil horizon at shallow depth and by volume scattering from the root mounds of healthy desert vegetation that locally stabilize blow sand. AIRSAR images obtained within the military range are also shown to be useful for detecting metallic military ordnance debris that is located either at the surface or covered by tens of centimeters to several meters of blow sand. The degree of detectability of this ordnance increases with SAR wavelength and is clearly maximized on P-band images that are processed in the cross-polarized mode (HV). This effect is attributed to maximum signal penetration at P-band and the enhanced PHV image contrast between the radar-bright ordnance debris and the radar-dark sandy desert. This article focuses on the interpretation of high resolution AIRSAR images but also Compares these airborne SAR images with those acquired from spacecraft sensors such as ERS-SAR and Space Radar Laboratory (SIR-C/X-SAR).Synthetic Aperture Radar (SAR) images acquired over part of the Yuma Desert in southwestern Arizona demonstrate the ability of C-band (5.7-cm wavelength), L-band (24.5 cm), and P-band (68 cm) AIRSAR signals to backscatter from increasingly greater depths reaching several meters in blow sand and sandy alluvium. AIRSAR images obtained within the Barry M. Goldwater Bombing and Gunnery Range near Yuma, Arizona, show a total reversal of C- and P-band backscatter contrast (image tone) for three distinct geologic units. This phenomenon results from an increasingly greater depth of radar imaging with increasing radar wavelength. In the case of sandy- and small pebble-alluvium surfaces mantled by up to several meters of blow sand, backscatter increases directly with SAR wavelength as a result of volume scattering from a calcic soil horizon at shallow depth and by volume scattering from the root mounds of healthy desert vegetation that locally stabilize blow sand. AIRSAR images obtained within the military range are also shown to be useful for detecting metallic military ordnance debris that is located either at the surface or covered by tens of centimeters to several meters of blow sand. The degree of detectability of this ordnance increases with SAR wavelength and is clearly maximized on P-band images that are processed in the cross-polarized mode (HV). This effect is attributed to maximum signal penetration at P-band and the enhanced PHV image contrast between the radar-bright ordnance debris and the radar-dark sandy desert. This article focuses on the interpretation of high resolution AIRSAR images but also compares these airborne SAR images with those acquired from spacecraft sensors such as ERS-SAR and Space Radar Laboratory (SIR-C/X-SAR).

No moving parts safe & arm apparatus and method with monitoring and built-in-test for optical firing of explosive systems

DOEpatents

Hendrix, J.L.

1995-04-11

A laser initiated ordnance controller apparatus which provides a safe and arm scheme with no moving parts. The safe & arm apparatus provides isolation of firing energy to explosive devices using a combination of polarization isolation and control through acousto-optical deviation of laser energy pulses. The apparatus provides constant monitoring of the systems status and performs 100% built-in-test at any time prior to ordnance ignition without the risk of premature ignition or detonation. The apparatus has a computer controller, a solid state laser, an acousto-optic deflector and RF drive circuitry, built-in-test optics and electronics, and system monitoring capabilities. The optical system is completed from the laser beam power source to the pyrotechnic ordnance through fiber optic cabling, optical splitters and optical connectors. During operation of the apparatus, a command is provided by the computer controller and, simultaneous with laser flashlamp fire, the safe & arm device is opened for approximately 200 microseconds which allows the laser pulse to transmit through the device. The arm signal also energizes the laser power supply and activates the acousto-optical deflector. When the correct fire format command is received, the acousto-optic deflector moves to the selected event channel, and the channel is verified to ensure the system is pointing to the correct position. Laser energy is transmitted through the fiber where an ignitor or detonator designed to be sensitive to optical pulses is fired at the end of the fiber channel. Simultaneous event channels may also be utilized by optically splitting a single event channel. The built-in-test may be performed anytime prior to ordnance ignition. 6 figures.

No moving parts safe & arm apparatus and method with monitoring and built-in-test for optical firing of explosive systems

DOEpatents

Hendrix, James L.

1995-01-01

A laser initiated ordnance controller apparatus which provides a safe and m scheme with no moving parts. The safe & arm apparatus provides isolation of firing energy to explosive devices using a combination of polarization isolation and control through acousto-optical deviation of laser energy pulses. The apparatus provides constant monitoring of the systems status and performs 100% built-in-test at any time prior to ordnance ignition without the risk of premature ignition or detonation. The apparatus has a computer controller, a solid state laser, an acousto-optic deflector and RF drive circuitry, built-in-test optics and electronics, and system monitoring capabilities. The optical system is completed from the laser beam power source to the pyrotechnic ordnance through fiber optic cabling, optical splitters and optical connectors. During operation of the apparatus, a command is provided by the computer controller and, simultaneous with laser flashlamp fire, the safe & arm device is opened for approximately 200 microseconds which allows the laser pulse to transmit through the device. The arm signal also energizes the laser power supply and activates the acousto-optical deflector. When the correct fire format command is received, the acousto-optic deflector moves to the selected event channel, and the channel is verified to ensure the system is pointing to the correct position. Laser energy is transmitted through the fiber where an ignitor or detonator designed to be sensitive to optical pulses is fired at the end of the fiber channel. Simultaneous event channels may also be utilized by optically splitting a single event channel. The built-in-test may be performed anytime prior to ordnance ignition.

Flight demonstration of flight termination system and solid rocket motor ignition using semiconductor laser initiated ordnance

NASA Astrophysics Data System (ADS)

Schulze, Norman R.; Maxfield, B.; Boucher, C.

1995-01-01

Solid State Laser Initiated Ordnance (LIO) offers new technology having potential for enhanced safety, reduced costs, and improved operational efficiency. Concerns over the absence of programmatic applications of the technology, which has prevented acceptance by flight programs, should be abated since LIO has now been operationally implemented by the Laser Initiated Ordnance Sounding Rocket Demonstration (LOSRD) Program. The first launch of solid state laser diode LIO at the NASA Wallops Flight Facility (WFF) occurred on March 15, 1995 with all mission objectives accomplished. This project, Phase 3 of a series of three NASA Headquarters LIO demonstration initiatives, accomplished its objective by the flight of a dedicated, all-LIO sounding rocket mission using a two-stage Nike-Orion launch vehicle. LIO flight hardware, made by The Ensign-Bickford Company under NASA's first Cooperative Agreement with Profit Making Organizations, safely initiated three demanding pyrotechnic sequence events, namely, solid rocket motor ignition from the ground and in flight, and flight termination, i.e., as a Flight Termination System (FTS). A flight LIO system was designed, built, tested, and flown to support the objectives of quickly and inexpensively putting LIO through ground and flight operational paces. The hardware was fully qualified for this mission, including component testing as well as a full-scale system test. The launch accomplished all mission objectives in less than 11 months from proposal receipt. This paper concentrates on accomplishments of the ordnance aspects of the program and on the program's implementation and results. While this program does not generically qualify LIO for all applications, it demonstrated the safety, technical, and operational feasibility of those two most demanding applications, using an all solid state safe and arm system in critical flight applications.

Energy Engineering Analysis Program, limited energy study of steam distribution systems, Hawthorne Army Ammunition Depot, Hawthorne, Nevada. Energy report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-07-01

This report summarizes all work of the Limited Energy Study of Steam Distribution Systems, Energy Engineering Analysis Program, Hawthorne Army Ammunition Depot (HWAAD), Nevada. The purpose of this limited energy study is to evaluate steam distribution and condensate collection systems in both the Industrial Area and Ordnance Area of HWAAD to develop a set of replacement actions that will reduce energy consumption and operating costs. These efforts consist of corrections and revisions to previously submitted funding requests. A number of facilities covering over 140,000 acres constitute HWAAD; however, this study was limited to the Industrial and Ordnance Areas.

Explosive Forming of Butt Welded Pipe Reducers.

DTIC Science & Technology

1979-04-01

Ao—A 072 I3Q NAVAL ORDNANCE STATION LOUISVILLE KY F~ G 13/it EXPLOSIVE FORMING OF BIJTT WELDED PIPE REDUCERS. (U) APR 79 M W JO$*4SON UNCLASSIFIED...NOSL MT OS2 _ Eli _ _El [LII] DliB I I —~~~~~~~~~~ I 4 1 V S -. RB’ORT NO. M1052 AP~t 1919v-fl o~toswE FORMING (j~~c BUTI WELDED PIPE RE~~~ A PQWECT...MING BUTT WELDED PIPE REDUCERS A PROJECT OP THE MANUFACTURING TECHNOLOGY PROGR AM NAVAL SEA SYST~~(S COMMA ND fiNAL REPORT NAVAL ORDNANCE STATION L

Laser diode initiated detonators for space applications

NASA Technical Reports Server (NTRS)

Ewick, David W.; Graham, J. A.; Hawley, J. D.

1993-01-01

Ensign Bickford Aerospace Company (EBAC) has over ten years of experience in the design and development of laser ordnance systems. Recent efforts have focused on the development of laser diode ordnance systems for space applications. Because the laser initiated detonators contain only insensitive secondary explosives, a high degree of system safety is achieved. Typical performance characteristics of a laser diode initiated detonator are described in this paper, including all-fire level, function time, and output. A finite difference model used at EBAC to predict detonator performance, is described and calculated results are compared to experimental data. Finally, the use of statistically designed experiments to evaluate performance of laser initiated detonators is discussed.

Advanced Geophysical Classification with the Marine Towed Array

NASA Astrophysics Data System (ADS)

Steinhurst, D.; Harbaugh, G.; Keiswetter, D.; Bell, T. W.; Massey, G.; Wright, D.

2017-12-01

The Marine Towed Array, or MTA, is an underwater dual-mode sensor array that has been successfully deployed at multiple marine venues in support of Strategic Environmental Research and Development Program (SERDP) and Environmental Security Technology Certification Program (ESTCP) demonstrations beginning in 2004. It provided both marine electromagnetic and marine magnetic sensors for detection and mapping of underwater UXO. The EMI sensor array was based on older technology, which in several ESTCP demonstrations has not been able to support advanced geophysical classification (AGC). Under ESTCP funding, the U.S. Naval Research Laboratory is in the process of upgrading the MTA with modern, advanced electromagnetic (EMI) electronics and replacing the sensor array with a modern, multistatic array design. A half-scale version of the proposed array has been built and tested on land. Six tri-axial receiver cubes were placed inside two- and three- transmit coil configurations in equivalent positions to design locations for the MTA wing. The responses of a variety of munitions items and test spheres were measured over a range of target-to-array geometries and in both static and simulated dynamic data collection modes. The multi-transmit coil configuration was shown to provide enhanced single-pass classification performance over the original single coil design, particularly as a function of target location relative to the centerline. The ability to go beyond anomaly detection and additionally classify detected anomalies from survey data would dramatically improve the state of the art for underwater UXO remediation by reducing costs and improving the efficiency of these efforts. The results of our efforts to return the MTA to service and validating the new EMI array's design for UXO detection and classification in the underwater environment will be the focus of this presentation.

Standardized UXO Technology Demonstration Site Scoring Record No. 946

DTIC Science & Technology

2017-07-01

VA 22350 U.S. Army Test and Evaluation Command Aberdeen Proving Ground, MD 21005-5001 Distribution Unlimited, July 2017. The use of a...Address . . . . . . . . . . . . . . . 4 2.1.2 System Description ...4 2.1.3 Data Processing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1.4 Data Submission

Standardized UXO Technology Demonstration Site Moguls Scoring Record Number 907 (Sky Research, Inc.)

DTIC Science & Technology

2008-08-01

day timeframe. 3.6 DEMONSTRATOR’S FIELD PERSONNEL Geophysicist: Craig Hyslop Geophysicist: John Jacobsen Geophysicist: Rob Mehl...Conover, John Wiley & Sons, 1980 , pages 144 through 151. APPENDIX F. ABBREVIATIONS F-1 (Page F-2 Blank) ADST = Aberdeen Data Services Team

Wide Area UXO Screening with the Multi-Sensor Fixed-Wing Airborne System MARS

DTIC Science & Technology

2008-02-01

snakes, lizards, and spiders may contain sufficient poison to warrant medical attention. In addition, ticks can spread Rocky Mountain spotted fever ...is extremely serious • Systemic hypothermia manifests itself in five stages of symptoms, including: (1) shivering ; (2) apathy, listlessness

Review and Synthesis of Evidence Regarding Environmental Risks Posed by Munitions Constituents (MC) in Aquatic Systems

DTIC Science & Technology

2017-10-31

default. Cover Image: Munitions response diver approaching an unexploded 1,000 pound General Purpose Bomb at Bahia Salina del Sur (Island of Vieques, PR...30 4.4 Isla de Vieques bombing range (PR, USA...Isla de Vieques Bombing Range site (PR)................................................................ 46 5.2.2 Halifax Harbor (Halifax, Canada

Evaluation and Improvement of the Defense Central Index of Investigations (DCII) - An Evaluation and Analysis Program for the U.S. Naval Postgraduate School.

DTIC Science & Technology

1985-11-22

occupations was that 20% of the explosive ordnance disposal specialists(55D) did not have a DIS dossier. Those in the other PSSP occupations showed...each have top secret eligibility ranging from: 61" (55D) to 24., (12 7). Finally, 29S of the explosive ordinance disposal specialists (55D) have no t...462XO Aircraft Armament Systems 1.5 71.8 .2 1.8 24.7 463XO Nuclear Weapons 1.9 75.8 .0 .9 21.4 464X0 Explosive Ordnance Disposal 2.7 63.0 .1 .9 33.3 545X1

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record No. 906 (Sky Research, Inc.)

DTIC Science & Technology

2008-08-01

DEMONSTRATOR’S FIELD PERSONNEL Geophysicist: Craig Hyslop Geophysicist: John Jacobsen Geophysicist: Rob Mehl 3.7 DEMONSTRATOR’S FIELD...Practical Nonparametric Statistics, W.J. Conover, John Wiley & Sons, 1980 , pages 144 through 151. APPENDIX F. ABBREVIATIONS F-1 (Page F-2

Active Tensor Magnetic Gradiometer System

DTIC Science & Technology

2007-11-01

Modify Forward Computer Models .............................................................................................2 Modify TMGS Simulator...active magnetic gradient measurement system are based upon the existing tensor magnetic gradiometer system ( TMGS ) developed under project MM-1328...Magnetic Gradiometer System ( TMGS ) for UXO Detection, Imaging, and Discrimination.” The TMGS developed under MM-1328 was successfully tested at the

EMI Array for Cued UXO Discrimination

DTIC Science & Technology

2011-02-07

that comprise a chain of former volcanoes extending from the southwest portion of the site to the coast. Due to its proximity to the tectonic ...interaction of the North American and Pacific crustal plates, the area is seismically active. Additional details are available in Reference 11. 4.2.3

Low-Cost Ultra-Wideband EM Sensor for UXO Detection and Classification

DTIC Science & Technology

2012-04-01

Mechanical System MOTU Mark of the Unicorn – a brand name for audio equipment MR Magneto-Resistance NIST National Institute of Standards and...magnetic surveys are able to detect ferrous bodies at a further distance than EMI measurements. Consequently , the magnetic anomaly is broader

UXO Discrimination in Cases with Overlapping Signatures

DTIC Science & Technology

2007-03-07

13. APPENDIX B: HFE -BIEM ..........................................................................................................290 - 7...First principals numerical solutions developed were a Hybrid Finite Element – Boundary Integral Equation Method ( HFE -BIEM) body of revolution (BOR...attacks, namely the Method of Auxiliary Sources (MAS) and the Hybrid Finite Element – Boundary Integral Equation Method ( HFE -BIEM). These work

Standardized UXO Technology Demonstration Site Blind Grid Record No. 904 (Sky Research, Inc.). EM61 MKII/Towed Array

DTIC Science & Technology

2008-09-01

DEMONSTRATOR’S FIELD PERSONNEL Geophysicist: Craig Hyslop Geophysicist: John Jacobsen Geophysicist: Rob Mehl 3.7 DEMONSTRATOR’S FIELD SURVEYING...Yuma Proving Ground Soil Survey Report, May 2003. 5. Practical Nonparametric Statistics, W.J. Conover, John Wiley & Sons, 1980 , pages 144 through

Standardized UXO Technology Demonstration Site, Scoring Record No. 942

DTIC Science & Technology

2014-09-01

the Mid- Atlantic Coastal Plain. Slopes range from 0 to 2 percent. 11 The U.S. Army Corps of Engineers Research and Development Center (ERDC...cleared woods (tree removal with only stumps remaining), partially cleared woods (including all underbrush and fallen trees), and virgin woods (i.e

Standardized UXO Technology Demonstration Site, Scoring Record No. 944

DTIC Science & Technology

2014-08-01

and in depressions of the Mid- Atlantic Coastal Plain. Slopes range from 0 to 2 percent. The U.S. Army Corps of Engineers Engineering Research...woods (including all underbrush and fallen trees), and virgin woods (i.e., woods in natural state with all trees, underbrush, and fallen trees left

EMI Array for Cued UXO Discrimination

DTIC Science & Technology

2010-09-16

that comprise a chain of former volcanoes extending from the southwest portion of the site to the coast. Due to its proximity to the tectonic ...interaction of the North American and Pacific crustal plates, the area is seismically active. A large portion of the site consists of hills and mountains

EMI Array for Cued UXO Discrimination

DTIC Science & Technology

2010-09-01

that comprise a chain of former volcanoes extending from the southwest portion of the site to the coast. Due to its proximity to the tectonic ...interaction of the North American and Pacific crustal plates, the area is seismically active. A large portion of the site consists of hills and mountains

2009 ESTCP UXO Discrimination Study, San Luis Obispo, CA

DTIC Science & Technology

2010-11-01

SUPERVISED LEARNING . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5 ACTIVE LEARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8...PERFORMANCE . . . . . . . . . . . . . . . . 29 7.2 ACTIVE LEARNING CLASSIFICATION PERFORMANCE . . . . . . . . . . . 30 8 COST ASSESSMENT 32 9... learning on EM61-array and TEMTADS data. During active learning , SIG started with no a priori labeled data, and acquired labels for a small subset that

High Density Lidar and Orthophotography in UXO Wide Area Assessment (Rev 1)

DTIC Science & Technology

2007-08-01

The demonstration provided important insights regarding the appropriate uses and confidence levels for both lidar and orthophoto technologies. At...Patterns ................................................................................ 3-34 3.7.18 Lidar and Orthophoto Positional Accuracy...02-D-2008 Page iii CONTENTS (Continued) APPENDICES A Lidar and Orthophoto Positional Accuracy Results B Combining Lidar Data from Multiple

Underground UXO: Are They a Significant Source of Explosives in Soil Compared to Low- and High-Order Detonations

DTIC Science & Technology

2004-12-01

steel in marine environments. Biofouling, 15(1– 3): 37–47. Videla, H.A. (2002) Prevention and control of biocorrosion . International Bio- deterioration...Prevention and control of biocorrosion . International Bio- deterioration and Biodegradation, 49(4): 259–270. Virtanen, S., and M. Buchler (2003

MetalMapper: A Multi-Sensor TEM System for UXO Detection and Classification

DTIC Science & Technology

2011-04-01

fluxgate magnetometer that provides reference heading to magnetic north. DeploymentCThe MM can be deployed either as a man-powered cart or as a...is a live site. Preliminary investigations included a magnetometer transect survey and an EMI survey over a larger area to assist in selecting a

Multi-Sensor Systems Development for UXO Detection and Discrimination: Hand-Held Dual Magnetic/Electromagnetic Induction Sensor

DTIC Science & Technology

2008-04-01

5 Fluxgate magnetometer ... magnetometer into digital format, and transmitted as a single serial data string to log the Cs and fluxgate magnetometer data. After procurement...Hardware The system hardware comprises an EMI sensor, Cs vapor magnetometer , fluxgate magnetometer , hand-held data acquisition computer, integrated

A Fast 4-D TEM System for UXO Characterization

DTIC Science & Technology

2003-07-30

responses for a small conductive and permeable sphere. Magnetic permeability is the curve parameter. Figure 2.10: Compass/ Tiltmeter package...each TCM2 record. The DOS clock on the HP200LX was manually set to UTC each day using the UTC time displayed on the Figure 2.10: Compass/ Tiltmeter

Standardized UXO Technology Demonstration Site Open Field Scoring Record No. 905 (Sky Research, Inc.) EM61 MKII/Towed Array

DTIC Science & Technology

2008-09-01

day timeframe. 3.6 DEMONSTRATOR’S FIELD PERSONNEL Geophysicist: Craig Hyslop Geophysicist: John Jacobsen Geophysicist: Rob Mehl 3.7...Practical Nonparametric Statistics, W.J. Conover, John Wiley & Sons, 1980 , pages 144 through 151. F-1 (Page F-2 Blank) APPENDIX F

Sub-Audio Magnetics: Miniature Sensor Technology for Simultaneous Magnetic and Electromagnetic Detection of UXO

DTIC Science & Technology

2010-07-01

is comprised of 4 x 40 m lengths of braided copper wire (Figure 29) with a diameter of 15 mm, capable of passing a 500 amp current. In normal...fuel tank and rubber hoses . Sub-Audio Magnetics: Technology for Simultaneous Magnetic and Electromagnetic Detection 77 Figure 31 Quad

Intelligent Data Fusion for Wide-Area Assessment of UXO Contamination. SERDP Project MM-1510. 2006 Annual Report

DTIC Science & Technology

2007-04-20

assistance, particularly Dr. Herb Nelson and Dr. Dan Steinhurst. 1 Executive Summary Background. The remediation of sites contaminated with...and applications,” Proc. of IEEE Intl. Conf. on Multisensor Fusion and Integration for Intelligent Systems, Taipei, Taiwan , R.O.C., Aug., 1999. 4

Spatial Statistical Model and Optimal Survey Design for Rapid Geophysical Characterization of UXO Sites

DTIC Science & Technology

2003-07-01

4, Gnanadesikan , 1977). An entity whose measured features fall into one of the regions is classified accordingly. For the approaches we discuss here... Gnanadesikan , R. 1977. Methods for Statistical Data Analysis of Multivariate Observations. John Wiley & Sons, New York. Hassig, N. L., O’Brien, R. F

UXO Detection and Characterization in the Marine Environment

DTIC Science & Technology

2008-11-01

65 APPENDIX B – NAD Puget Sound Historical Documents ............................................CD APPENDIX C...16 18. A part of Ostrich Bay adjacent to the Naval Ammunition Depot Puget Sound is shown during...viii EXECUTIVE SUMMARY The second demonstration of the Marine Towed Array took place June 12-30, 2006 on Ostrich Bay ( Puget Sound ) in the state

Statistical and Adaptive Signal Processing for UXO Discrimination for Next-Generation Sensor Data

DTIC Science & Technology

2009-09-01

using the energies of all polarizations as features in a KNN classifier variant resulted in 100% probability of detection at a probability of false...International Conference on Acoustics, Speech , and Signal Processing, vol. V, 2005, pp. 885-888. [12] C. Kreucher, K. Kastella, and A. O. Hero

Review and Synthesis of Evidence Regarding Environmental Risks Posed by Munitions Constituents (MC) in Aquatic Systems

DTIC Science & Technology

2017-10-01

Munitions response diver approaching an unexploded 1,000 pound General Purpose Bomb at Bahia Salina del Sur (Island of Vieques, PR). Photo provided...30 4.4 Isla de Vieques bombing range (PR, USA) .................................................... 30 4.4.1 Site...45 5.2 Sites reporting MC contamination in water samples ................................... 46 5.2.1 Isla de Vieques Bombing

Air Cushion Crash Rescue Vehicle (ACCRV)

DTIC Science & Technology

1987-10-01

capability to operate over rough and low strength ground surfaces, especially soft, wet ground or marsh and snow, with no capability for overwater...operation. In a wartime environment , fire fighting and res- cue will be further restricted because of craters, debris or unexploded bombs. Improved...swamps and, of course, in more conventional environments on or about airports. The integration of an air cushion system with a paddle track propulsor

Characterization of Air Emissions from Open Burning and ...

EPA Pesticide Factsheets

Emissions from open burning (OB) and open detonation (OD) of military ordnance and static fires (SF) of rocket motors were sampled in fall, 2013 at the Dundurn Depot (Saskatchewan, Canada). Emission sampling was conducted with an aerostat-lofted instrument package termed the “Flyer” that was maneuvered into the downwind plumes. Forty-nine OB events, 94 OD events, and 16 SF on four propellants types (Triple base, 105 M1, 155 M4A2 white bag, and 155 M6 red bag), two smokes (HC grenade and red phosphorus), five explosive types (Trigran, C4, ANFO, ANFO+HC grenade, and ANFO+Flare), and two rocket motors types (CVR-7 and MK 58) resulted in emission factors for particulate matter (PM), carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), volatile organic compounds (VOCs), chlorine species (HCl, chloride, chlorate, perchlorate), polychlorinated dibenzodioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) and PM-based metals. These data provide Canada and the United States with additional air emissions data to support health risk assessments and permitting for safe treatment of military ordnance by OB/OD/SF. In addition, the data will be used to conduct air dispersion modelling assessing the impact of treatment of various ordnance on the air quality, to support mandatory reporting requirements of the Canadian Environmental Protection Act (CEPA), the National Pollutant Release Inventory (NPRI), and to update the Canadian Ammunition Chemical Database.Result

Advanced release technologies program

NASA Technical Reports Server (NTRS)

Purdy, Bill

1994-01-01

The objective of the ARTS program was to develop lighter and less expensive spacecraft ordnance and release systems that answer to the requirements of a wide variety of spacecraft applications. These improvements were to be evaluated at the spacecraft system level, as it was determined that there were substantial system-level costs associated with the present ordnance and release subsystems. New, better devices were to be developed, then flight qualified, then integrated into a flight experiment in order to prove the reliability required for their subsequent use on high-reliability spacecraft. The secondary goal of the program was to quantify the system-level benefits of these new subsystems based upon the development program results. Three non-explosive release mechanisms and one laser-diode-based ordnance system were qualified under the program. The release devices being developed were required to release high preloads because it is easier to scale down a release mechanism than to scale it up. The laser initiator developed was required to be a direct replacement for NASA Standard Initiators, since these are the most common initiator in use presently. The program began in October, 1991, with completion of the flight experiment scheduled for February, 1994. This paper provides an overview of the ARTS program, discusses the benefits of using the ARTS components, introduces the new components, compares them with conventional systems and each other, and provides recommendations on how best to implement them.

Remedial investigation concept plan for the groundwater operable units at the chemical plant area and the ordnance works area, Weldon Spring, Missouri

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1999-07-15

The U.S. Department of Energy (DOE) and the U.S. Department of the Army (DA) are conducting cleanup activities at two properties--the DOE chemical plant area and the DA ordnance works area (the latter includes the training area)--located in the Weldon Spring area in St. Charles County, Missouri. These areas are on the National Priorities List (NPL), and cleanup activities at both areas are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. DOE and DA are conducting a joint remedial investigation (RI) and baseline risk assessment (BRA) as part of the remedial investigation/feasibility studymore » (RI/FS) for the groundwater operable units for the two areas. This joint effort will optimize further data collection and interpretation efforts and facilitate overall remedial decision making since the aquifer of concern is common to both areas. A Work Plan issued jointly in 1995 by DOE and the DA discusses the results of investigations completed at the time of preparation of the report. The investigations were necessary to provide an understanding of the groundwater system beneath the chemical plant area and the ordnance works area. The Work Plan also identifies additional data requirements for verification of the evaluation presented.« less

Changing Manufacturing Technology and Jobs in Defense Industries.

ERIC Educational Resources Information Center

Oliver, Richard P.

1983-01-01

Provides information on the current status of computer-assisted manufacturing, current employment, and plans for new technology in three defense-related industries: aircraft, shipbuilding, and ordnance. (SK)

Demonstration and Validation of an Improved Airborne Electromagnetic System for UXO Detection and Mapping

DTIC Science & Technology

2010-05-01

William E. Doll Battelle 105 Mitchell Road Suite 103 Oak Ridge, TN 37830 865-483-2548 865-599-6165 dollw@battelle.org Airborne Survey...Manager David T. Bell Battelle 105 Mitchell Road Suite 103 Oak Ridge, TN 37830 865-483-2547 865-250-0578 belldt@battelle.org Battelle-Oak Ridge

The UXO Discrimination Study at the Former Camp Sibert

DTIC Science & Technology

2009-01-01

extrinsic and intrinsic parameters of the target of interest. Extrinsic parameters include the target’s location (easting and northing), orientation and...1-2 1.2 Demonstration Motivation ....................................................................... 1-3 1.3 General Approach...subset of these points. The remaining points are discussed in the summary final report produced by ESTCP [15]. 1-3 1.2 DEMONSTRATION MOTIVATION

Demonstration of an Enhanced Vertical Magnetic Gradient System for UXO

DTIC Science & Technology

2008-12-01

fluxgate magnetometers , data recording console, laser altimeter, and acoustic altimeters were tested to ensure proper operation and performance. The VG...Simultaneous Electromagnetic Induction and Magnetometer System WAA wide area assessment ACKNOWLEDGEMENTS We wish to express our sincere...sensors. The benefits of vertical gradient (VG) configurations in magnetometer systems are common knowledge, and these configurations are routinely

EMI Modeling for UXO Detection and Discrimination Underwater

DTIC Science & Technology

2011-12-01

detection and discrimination underwater,? submitted to the Strategic Environmental Research and Development Program (SERDP) in response to the...phenomena from highly conducting and permeable metallic objects in underwater environments, and 3) investigate the impact of the electromagnetic parameters of...to the Department of Defense Strategic Environmental Research and Development Program (SERDP). The publication of this report does not indicate

Method and apparatus for selective capture of gas phase analytes using metal .beta.-diketonate polymers

DOEpatents

Harvey, Scott D [Kennewick, WA

2011-06-21

A process and sensor device are disclosed that employ metal .beta.-diketonate polymers to selectively capture gas-phase explosives and weaponized chemical agents in a sampling area or volume. The metal .beta.-diketonate polymers can be applied to surfaces in various analytical formats for detection of: improvised explosive devices, unexploded ordinance, munitions hidden in cargo holds, explosives, and chemical weapons in public areas.

View of camera station located northeast of Building 70022, facing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of camera station located northeast of Building 70022, facing northwest - Naval Ordnance Test Station Inyokern, Randsburg Wash Facility Target Test Towers, Tower Road, China Lake, Kern County, CA

View of building 11050, showing metal clad addition on east ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050, showing metal clad addition on east elevation, looking southwest. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Machine Shop, C Street, China Lake, Kern County, CA

View showing base of Building 70021 with Building 70022 in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View showing base of Building 70021 with Building 70022 in background, facing southeast - Naval Ordnance Test Station Inyokern, Randsburg Wash Facility Target Test Towers, Tower Road, China Lake, Kern County, CA

Detail view of base of Building 70021, showing Building 70022 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of base of Building 70021, showing Building 70022 (background), facing southeast - Naval Ordnance Test Station Inyokern, Randsburg Wash Facility Target Test Towers, Tower Road, China Lake, Kern County, CA

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). DRILLING - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). MACHINE SHOP - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). OLIVING - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). FINAL INSPECTION - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

High Density Lidar and Orthophotography in UXO Wide Area Assessment, Phase 2. Former Camp Beale Demonstration Site. Addendum, Revision 2

DTIC Science & Technology

2008-01-01

the delivery tiles . For the Former Camp Beale site, orthophotos were created in blocks of 2.675 square kilometers, in order to keep file sizes...3-19 3.7.12 Data Density Effects - Orthophotos ....................................................... 3-20 3.7.13 Data... Orthophoto Positional Accuracy ........................................... 3-29 4.0 PERFORMANCE ASSESSMENT

Advanced UXO Discrimination using Magnetometry: Understanding Remanent Magnetization

DTIC Science & Technology

2009-09-01

moments of steel samples. The MRIP comprises six three-component fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples...comprises six three- component fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples are placed on the holder... fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples are placed on the holder and are slowly spun through two

Integration of Advanced Statistical Analysis Tools and Geophysical Modeling

DTIC Science & Technology

2012-08-01

Carin Duke University Douglas Oldenburg University of British Columbia Stephen Billings Leonard Pasion Laurens Beran Sky Research...data processing for UXO discrimination is the time (or frequency) dependent dipole model (Bell and Barrow (2001), Pasion and Oldenburg (2001), Zhang...described by a bimodal distribution (i.e. two Gaussians, see Pasion (2007)). Data features are nonetheless useful when data quality is not sufficient

Demonstration of Advanced EMI Models for Live-Site UXO Discrimination at Former Camp Butner, North Carolina

DTIC Science & Technology

2012-05-01

GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7 . PERFORMING ORGANIZATION NAME(S...2.3.3 Classification using template matching ...................................................... 7 2.4 Details of classification schemes... 7 2.4.1 Camp Butner TEMTADS data inversion and classification scheme .......... 9

Simultaneous Inversion of UXO Parameters and Background Response

DTIC Science & Technology

2012-03-01

11. SUPPLEMENTARY NO TES 12a. DISTRIBUTION/AVAILABILITY STATEMENT Unclassified/Unlimited 12b. DISTRIBUTIO N CODE 13. ABSTRACT (Maximum 200...demonstrated an ability to accurate recover dipole parameters using the simultaneous inversion method. Numerical modeling code for solving Maxwell’s...magnetics 15. NUMBER O F PAGES 160 16. PRICE CODE 17. SECURITY CLASSIFICATIO N OF REPORT Unclassified 18. SECURITY

Continuous Monitoring of Mobility, Burial and Re exposure of Underwater Munitions in Energetic Near Shore Environments

DTIC Science & Technology

2017-01-01

parameters on Wasque Shoals ..................................................... 22 Figure 19. Rotary sonar imagery showing migrating mega- ripples and the...shown by the green and yellow lines reveals the convergence and divergence of the migrating mega- ripples ...26 Figure 24. Succesive rotary sonar images showing transient burial and reexposure of a surrogate UXO by migrating mega- ripples

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). LARGE HOLE-OPENING - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Overall view of administration area with building 11110 in background, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Overall view of administration area with building 11110 in background, looking east from facility gate. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Pilot Plant Road, China Lake, Kern County, CA

View of building 11070, with building 11050 in the background ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11070, with building 11050 in the background (left side). Looking northeast. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Maintenance Shop, C Street, China Lake, Kern County, CA

View of hoist southeast of Building 70022. facing northwest. Building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of hoist southeast of Building 70022. facing northwest. Building 70022 is in background - Naval Ordnance Test Station Inyokern, Randsburg Wash Facility Target Test Towers, Tower Road, China Lake, Kern County, CA

View of building 11050, showing two additions on east and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050, showing two additions on east and north side. Looking southwest. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Machine Shop, C Street, China Lake, Kern County, CA

View of building 11070 showing vents and forced air system ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11070 showing vents and forced air system on east side, looking southwest. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Maintenance Shop, C Street, China Lake, Kern County, CA

22. DETAILCATWALKS OF THE UPPER LEVEL OF BUILDING 36 AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. DETAIL--CATWALKS OF THE UPPER LEVEL OF BUILDING 36 AT THE INTERSECTION OF THE EAST AND NORTH WINGS. - Navy Yard, Ordnance Building, Intersection of Paulding & Kennon Streets, Washington, District of Columbia, DC

View of building 11180 looking southeast, showing wide eaves, eave ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11180 looking southeast, showing wide eaves, eave brackets, and flared elements at sill line. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Office Building, Fourth Street, China Lake, Kern County, CA

Photographic copy of photograph (original print in possession of William ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). PASTING JEWEL BLANKS, PREPARATION FOR DRILLING. - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Aeromagnetic maps and second vertical derivative maps of Great Sitkin Island, Northern Adak Island, and part of northeastern Umnak Island, Alaska

USGS Publications Warehouse

Zietz, Isidore; Henderson, Roland G.

1949-01-01

The eight attached maps were constructed from data taken on Project Volcano in the summer of 1947. The project was sponsored by the Office of Naval Research and conducted by the U.S. Geological Survey in cooperation with the Naval Ordnance Laboratory. Field work was done by Fred Keller, Jr., and J. L. Meuschke, Geophysicists of the U.S. Geological Survey, and by L. R. Alldredge, Physicist of the Naval Ordnance Laboratory. The instrument used was a modified AN/ASQ-3A flux-gate type total field magnetometer mounted in the tailcone of a PBY-5A aircraft. It is hoped that observation of the magnetic fields over volcanic areas over a period of years, may lead to prognostication of volcanic activity. These maps represent the results of the first of such surveys.

High Density Lidar and Orthophotography in UXO Wide Area Assessment Phase 2. Final Report Addendum for Former Camp Beale Demonstration Site, Revision 2

DTIC Science & Technology

2008-01-01

color balancing, and trimming to the delivery tiles . For the Former Camp Beale site, orthophotos were created in blocks of 2.675 square kilometers, in...3-19 3.7.12 Data Density Effects - Orthophotos ...3-27 3.7.18 Lidar and Orthophoto Positional Accuracy ........................................... 3-29 4.0 PERFORMANCE ASSESSMENT

Demonstration of an Enhanced Vertical Magnetic Gradient System for UXO

DTIC Science & Technology

2008-04-01

flights were conducted and results evaluated. The cesium magnetometers , GPS systems (positioning and attitude), fluxgate magnetometers , data...makes a measurement and when it is time-stamped and recorded. This applies to the magnetometers , fluxgate and the GPS. Accurate positioning...requires a correction for this lag. Time lags between the magnetometers , fluxgate and GPS signals were measured by a proprietary utility. This utility

UXO Burial Prediction Fidelity

DTIC Science & Technology

2017-07-01

been developed to predict the initial penetration depth of underwater mines . SERDP would like to know if and how these existing mine models could be...designed for near-cylindrical mines —for munitions, however, projectile-specific drag, lift, and moment coefficients are needed for estimating...as inputs.  Other models have been built to estimate these initial conditions for mines dropped into water.  Can these mine models be useful for

Demonstration of the Berkeley UXO Discrimination at Live Sites

DTIC Science & Technology

2010-02-01

BUD then occupied each of the 11 points and acquired a stationary measurement. The cart was equipped with a two-component tiltmeter and three...component magnetometer. Both devices were calibrated before the survey. The tiltmeters readings were used to compute the cart pitch (positive pitch...cart front down = negative tiltmeter change), and roll (positive=cart rightside down - positive tiltmeter change). The magnetometer values were used to

UXO Burial Prediction Fidelity: A Summary

DTIC Science & Technology

2017-07-01

should not be construed as representing the official position of either the Department of Defense or the sponsoring organization. For More Information ...equilibrium. Any complete picture of munition evolution in sediment would need to account for these effects. More relevant to the present topic: these...of adds uncertainty to predictions of munition fate, and assessments of risk probabilities would need to account for the statistical distribution of

Phenomenology and Signal Processing for UXO/Clutter Discrimination

DTIC Science & Technology

2009-08-01

29 Figure 25. (a) Pasion -Oldenburg model fit to the EMI response of a 4.2 inch mortar aligned transverse to the primary field...b) Comparison between the two-component and Pasion - Oldenburg model fits to the 4.2 inch mortar response...30 Figure 26. Pasion -Oldenburg exponent γ compared to the magnetic crossover time τM for model fits to EMI data collected

Report Of Environmental Security Technology Certification Program (ESTCP) UXO Discrimination Study Support Activities: Former Camp Sibert, Etowah and St. Clair Counties, Alabama

DTIC Science & Technology

2007-11-01

PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) PARSONS 4890 University Square Suite 2 Huntsville, Alabama 35816 8 . PERFORMING ORGANIZATION REPORT NUMBER...PERSON a. REPORT unclassified b. ABSTRACT unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8 -98) Prescribed by ANSI Std Z39-18...Intrusive Investigation Results ...................................................................................... 8 8.2 CLUSTER ANOMALIES

Laser Line Scan System for UXO Characterization

DTIC Science & Technology

2012-04-01

they geometrically rectified. The Year 2 survey collected LLSS images from seven passes over two separate calibration strings and six passes over two...Microsoft DOS-based software tool. According to the side- by-side comparisons shown in Figure 9, the morphometrics were relatively equal between...survey. Note: The imagery in this figure is not presented at full resolution nor geometrically rectified. LLSS Targets, Pass One 1. Danforth

2009 ESTCP UXO Classification Study, San Luis Obispo, CA

DTIC Science & Technology

2012-04-01

and faulted. The site is underlain by a mixture of metamorphic , igneous, and sedimentary rocks less than 200 million years old. Scattered...measured data is shown in the upper left map, the model parameters are displayed in the lower center window, and the forward model generated using the...8 Figure 2-5. Derived response coefficients for a 40-mm projectile using the measurements of which the

Multiple factors affect a population of Agassiz's desert tortoise (Gopherus agassizii) in the Northwestern Mojave Desert

USGS Publications Warehouse

Berry, Kristin H.; Yee, Julie L.; Coble, Ashley A.; Perry, William M.; Shields, Timothy A.

2013-01-01

Numerous factors have contributed to declines in populations of the federally threatened Agassiz's Desert Tortoise (Gopherus agassizii) and continue to limit recovery. In 2010, we surveyed a low-density population on a military test facility in the northwestern Mojave Desert of California, USA, to evaluate population status and identify potential factors contributing to distribution and low densities. Estimated densities of live tortoises ranged spatially from 1.2/km2 to 15.1/km2. Although only one death of a breeding-age tortoise was recorded for the 4-yr period prior to the survey, remains of 16 juvenile and immature tortoises were found, and most showed signs of predation by Common Ravens (Corvus corax) and mammals. Predation may have limited recruitment of young tortoises into the adult size classes. To evaluate the relative importance of different types of impacts to tortoises, we developed predictive models for spatially explicit densities of tortoise sign and live tortoises using topography (i.e., slope), predators (Common Raven, signs of mammalian predators), and anthropogenic impacts (distances from paved road and denuded areas, density of ordnance fragments) as covariates. Models suggest that densities of tortoise sign increased with slope and signs of mammalian predators and decreased with Common Ravens, while also varying based on interaction effects involving these predictors as well as distances from paved roads, denuded areas, and ordnance. Similarly, densities of live tortoises varied by interaction effects among distances to denuded areas and paved roads, density of ordnance fragments, and slope. Thus multiple factors predict the densities and distribution of this population.

Second International Airborne Remote Sensing Conference and Exhibition

NASA Technical Reports Server (NTRS)

1996-01-01

The conference provided four days of displays and scientific presentations on applications, technology, a science of sub-orbital data gathering and analysis. The twelve displayed aircraft equipped with sophisticated instrumentation represented a wide range of environmental and reconnaissance missions,including marine pollution control, fire detection, Open Skies Treaty verification, thermal mapping, hydrographical measurements, military research, ecological and agricultural observations, geophysical research, atmospheric and meterological observations, and aerial photography. The U.S. Air Force and the On-Site Inspection Agency displayed the new Open Skies Treaty verification Boeing OC 135B that promotes international monitoring of military forces and activities. SRl's Jetstream uses foliage and ground penetrating SAR for forest inventories, toxic waste delineation, and concealed target and buried unexploded ordnance detection. Earth Search Sciences's Gulfstream 1 with prototype miniaturized airborne hyperspectral imaging equipment specializes in accurate mineral differentiation, low-cost hydrocarbon exploration, and nonproliferation applications. John E. Chance and the U.S. Army Corps of Engineers displayed the Bell 2 helicopter with SHOALS that performs hydrographic surveying of navigation projects, coastal environment assessment, and nautical charting surveys. Bechtel Nevada and U.S. DOE displayed both the Beech King AIR B-200 platform equipped to provide first response to nuclear accidents and routine environmental surveillance, and the MBB BO-105 helicopter used in spectral analysis for environmental assessment and military appraisal. NASA Ames Research Center's high-altitude Lockheed ER-2 assists in earth resources monitoring research in atmospheric chemistry, oceanography, and electronic sensors; ozone and greenhouse studies and satellite calibration and data validation. Ames also showcased the Learjet 24 Airborne Observatory that completed missions in Venus cloud cover analysis, Quadantid meteor shower studies, extra-solar far infrared ionic structure lines measurement, Cape Kennedy launch support, and studies in air pollution, The Products and Services Exhibit showcased new sensor and image processing technologies, aircraft data collection services, unmanned vehicle technology, platform equipment, turn-key services, software a workstations, GPS services, publications, and processing and integration systems by 58 exhibitors. The participation of aircraft users and crews provided unique dialogue between those who plan data collection a operate the remote sensing technology, and those who supply the data processing and integration equipment. Research results using hyperspectral imagery, radar and optical sensors, lidar, digital aerial photography, a integrated systems were presented. Major research and development programs and campaigns we reviewed, including CNR's LARA Project and European Space Agency's 1991-1995 Airborne Campaign. The pre-conference short courses addressed airborne video, photogrammetry, hyperspectral data analysis, digital orthophotography, imagery and GIS integration, IFSAR, GPS, and spectrometer calibration.

Petrology and Geochronology of Kaula Volcano lavas: An off-axis window into the Hawaiian Mantle Plume

NASA Astrophysics Data System (ADS)

Garcia, M. O.; Weis, D.; Jicha, B. R.; Tree, J. P.; Bizimis, M.

2014-12-01

The Hawaiian Islands extend NW for 625 km from Lō'ihi to Ka'ula island. One anomalous feature cross-cutting the Hawaiian Islands is the Kaua'i Ridge, a 165 km-long bathymetric high with three well-defined gravity highs. These gravity highs are centered under or near the islands of Ka'ula, Ni'ihau and Kaua'i, and represent the cores of three shield volcanoes whose volumes decrease dramatically with distance from the axis of the Hawaiian Chain (Kaua'i, 58 x 103 km3, Ni'ihau x 103 km, Ka'ula 10 x 103 km; Robinson and Eakins 2006). Ka'ula Volcano, on the SW end of the Kaua'i Ridge, is centered 100 km off the axis of the Hawaiian mantle plume. The volcano is capped by a small island, which is a remnant of a nephelinitic tuff cone. The cone contains abundant accidental bombs of lava (tholeiite, phonolite and basanite), peridotite and pyroxenite, and unexploded ordnance from US military bombing. Two JASON dives on the flanks of Ka'ula recovered only alkalic lavas. Three stage of Ka'ula volcanism have been identified from sampling the volcanic bombs and flanks of the volcano. These rocks were dated using 40Ar/39Ar methods for the basalts and K-Ar for the phonolites. A tholeiitic shield basalt yielded an age of 6.2 Ma, the oldest reliable age for any Hawaiian Island tholeiite. Post-shield phonolites gave ages of 4.0 to 4.2 Ma (Garcia et al., 1986) and rejuvenation stage alkalic basalts yielded ages of 1.9 to 0.5 Ma. These ages are nearly identical to those for the same stages for adjacent Ni'ihau volcano but slightly older than on Kauai, 100 km to the NE (Sherrod et al. 2007). Thus, volcanism was nearly simultaneous along Kaua'i Ridge. The new age results extend to 420 km the distance within the Hawaiian Islands that experienced coeval rejuvenated volcanism. Geochemically, the rejuvenated and tholeiitic lavas from the Kaua'i Ridge are very similar with mixed source signatures of Loa and Kea trend compositions. Mixed Loa-Kea sources have been found for many other Hawaiian volcanoes. These results indicate that the Hawaiian mantle plume was broadly homogeneous over 100 km distance but also heterogeneous on a fine scale. Garcia et al., 1986. Contr. Mineral. Petrol. 94, 461-471; Robinson and Eakins, 2006. J. Volcanol. Geotherm. Res. 151, 309-317; Sherrod et al., 2007. USGS Open-File Rept. 2007-1089.

View of building 11050 showing south side with modern addition ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050 showing south side with modern addition on the left and freestanding structure in the center. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Maintenance Shop, C Street, China Lake, Kern County, CA

View of building 11050. With view of building 11070 (See ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050. With view of building 11070 (See HABS No. CA 2774-B) in background. Looking southwest. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Machine Shop, C Street, China Lake, Kern County, CA

31. DETAILMETAL ROOF TRUSS OF THE NORTH WING OF BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. DETAIL--METAL ROOF TRUSS OF THE NORTH WING OF BUILDING 36 LOOKING WEST TO THE WALL PARTITIONING BUILDING 36 AND BUILDING 33. - Navy Yard, Ordnance Building, Intersection of Paulding & Kennon Streets, Washington, District of Columbia, DC

Navy Expeditionary Support

DTIC Science & Technology

2010-04-27

Officer, Explosive Ordnance Disposal Mobil Unit TWO, conversation with author, March 2010. 12 Marc Carmichael , Lieutenant Commander, U.S. Navy, Deputy...Combat Service Support Reorganization Conference, 17-27 Jan 1977. Washington, D. C.: Headquarters U.S. Marine Corps, January 17, 1977. "Armed

Oblique view of building 11050, showing east and south sides, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Oblique view of building 11050, showing east and south sides, looking northwest. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Fire Station & Marine Barracks, D Street, at corner of 4th Street, China Lake, Kern County, CA

About White Sands Missile Range

NASA Technical Reports Server (NTRS)

1991-01-01

Information on the White Sands Missile Range is given in viewgraph form. Navy programs, test sites, rocket programs, research rockets' booster capacity, current boost capabilities, ordnance and payload assembly areas, commercial space launch history and agreements, and lead times are among the topics covered.

76 FR 62378 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... resulting from ordnance. DPI could result from inert bombs, gunnery ammunition, and shrapnel from live...-explosive items (bombs, missiles, and drones) to impact marine mammals. As shown in the 2002 Final PEA and...

Environmental Assessment for the Proposed Explosive Ordnance Disposal Detonation Site on Juniper Butte Range

DTIC Science & Technology

2012-05-01

squirreltail (Sitanion hystrix), phlox (Phlox sp.), Lupine ( Lupinus sp.), and Indian paintbrush (Castilleja sp.). Rabbitbrush (Chrysothamnus sp.) is...longifolia), Hood’s phlox (Phlox hoodii), low pussytoes (Antennaria dimorpha), Sandbergs bluegrass, lupine ( Lupinus arbustus), and bottlebrush

National Defense Center for Energy and Environment 2007 Annual Report

DTIC Science & Technology

2007-01-01

Catcher does this and more. Using a unique, self - healing elastomeric top cover that keeps out moisture and minimizes oxygen content, the Bullet...claw to enable remote-controlled excavation of UXO. In this effort the NDCEE teamed with the Air Force Research Laboratory (AFRL) Robotic Research...Group, whose mission is to “develop and advance robotic technologies that will protect, support, and augment the warfighter in the accomplishment of

UXO Live Site Classification Demonstrations: A Retrospective Summary

DTIC Science & Technology

2017-10-01

performance ROC Curve Number of True Clutter Incorrectly Classified TO I R em ed ia tio n: Pe rc en t o f T ru e TO I Co rr ec tly C la ss ifi ed...rocket, 382 practice bomb , M103 bomb nose fuze, 100lb bomb , M1 practice bomb MPV, TEMTADS 2x2 2014 Waikoloa Waikoloa, HI 9 small ISO, 37mm, medium

Dipole Models for UXO Discrimination at Live Sites

DTIC Science & Technology

2017-05-01

Discriminator CCR Combined Classifier Ranking cm Centimeter(s) EM Electromagnetic EMI Electromagnetic Induction ESTCP Environmental Security Technology...fraction of the anomalies as arising from non-hazardous items that could be safely left in the ground. Of particular note, the contractor EM -61-MK2 cart...use of classification metrics applied to production quality EM - 61 data, it was possible to significantly reduce the number of clutter items excavated

Magnetic Sensors with Picotesla Magnetic Field Sensitivity at Room Temperature

DTIC Science & Technology

2008-06-01

such small fields require cryogenic cooling such as SQUID sensors, require sophisticated detection systems such as atomic magnetometers and fluxgate ... magnetometers , or have large size and poor low frequency performance such as coil systems. [3-7] The minimum detectable field (the field noise times...Kingdon, "Development of a Combined EMI/ Magnetometer Sensor for UXO Detection," Proc. Symposium on the Applications of Geophysics to Environmental and

An EM System with Dynamic Multi-Axis Transmitter and Tensor Gradiometer Receiver

DTIC Science & Technology

2011-06-01

main difference between the spatial behavior of target anomalies measured with a magnetometer and those we measured with an EM system is in the nature...environmental and UXO applications, current efforts include the development of tensor magnetic gradiometers based on triaxial fluxgate technology by the USGS...Superconducting gradiometer/ Magnetometer Arrays and a Novel Signal Processing Technique. IEEE Trans. on Magnetics, MAG-11(2), 701-707. EM Tensor

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record Number 891

DTIC Science & Technology

2008-08-01

magnetometers (Foerster CON650 gradiometers) and RTK-DGPS georeferencing will be used. The spacing between the individual fluxgate sensors will be 25 cm...used for data acquisition usually ranges from 8 to 32. b. For the demonstration at Aberdeen Proving Ground, a system with eight fluxgate ...up to 32 fluxgate gradiometers (for the APG demonstration: eight fluxgate gradiometers), a robust, all-terrain trailer, the MonMX data acquisition

Isolating and Discriminating Overlapping Signatures in Cluttered Environments

DTIC Science & Technology

2011-05-11

Lin-Ping Song, Douglas W. Oldenburg, Leonard R. Pasion , and Stephen D. Billings. Transient electromagnetic inversion for multiple targets. SPIE...and Remote Sensing, 39(6):1294 – 1298, 2001. ISSN 0196-2892. 33, 34 [52] L. R. Pasion and D. W. Oldenburg. A discrimination algorithm for UXO using...R. Pasion , Douglas W. Oldenburg, and Stephen D. Billings. Com- puting transient electromagnetic response of a metallic object with a spheroidal

Wide Area Assessment Demonstration of LiDAR and Orthophotography at Borrego Maneuver Area, Phase II Innovative Multi-Sensor Airborne Wide Area Assessment of UXO Sites, Version 2.0

DTIC Science & Technology

2007-12-03

and reference datums, in addition to other field positioning tasks. 3.5.3. Navigation Systems An Applanix 510 A/V POS system was co-mounted with...Cal and POS EO from Applanix Corp. lmageStation Suite from Z/1 Imaging Images: Camera and Data Recorder · I SAT Aerial Triangulation Software

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record No. 764

DTIC Science & Technology

2006-04-01

Attainable accuracy of depth (z) ± 0.3 meter Detection performance for ferrous and nonferrous metals : will detect ammunition components 20-mm...ASSOCIATES, INC. 6832 OLD DOMINION DRIVE MCLEAN, VA 22101 TECHNOLOGY TYPE/PLATFORM: MULTI CHANNEL DETECTOR SYSTEM (AMOS)/TOWED PREPARED BY: U.S...Multi Channel Detector System (AMOS)/Towed, MEC 18. NUMBER OF PAGES 19a. NAME OF RESPONSIBLE PERSON a. REPORT Unclassified b. ABSTRACT

Remote Excavation of Heavily Contaminated UXO Sites. The Range Master

DTIC Science & Technology

2007-09-05

NUMBER 5c. PROGRAM ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 6. AUTHOR(S) 7. PERFORMING ORGANIZATION NAME(S) AND...Master) ESTCP Project UX-200327 ii Final Phase II Report, September 2007 3.5.5 Sampling Plan...Explosive HSP Health and Safety Program HTRW Hazardous, Toxic, and Radioactive Waste HTW Hazardous and Toxic Waste HW Hazardous Waste IAW In

The UXO Classification Demonstration at San Luis Obispo, CA

DTIC Science & Technology

2010-09-01

Set ................................45  2.17.2  Active Learning Training and Test Set ..........................................47  2.17.3  Extended...optimized algorithm by applying it to only the unlabeled data in the test set. 2.17.2 Active Learning Training and Test Set SIG also used active ... learning [12]. Active learning , an alternative approach for constructing a training set, is used in conjunction with either supervised or semi

UXO Detection and Characterization in the Marine Environment

DTIC Science & Technology

2009-12-01

10 Figure 8. A part of Ostrich Bay adjacent to the Naval Ammunition Depot Puget Sound during the period of its...large-scale demonstration focus on a marine geophysical magnetometry survey of Ostrich Bay adjacent to the Former Naval Ammunition Depot – Puget Sound ...The Puget Sound Demonstration was also supported by NAVFAC Northwest, the current manager of the site. The Navy Project Manager is Mr. Mark Murphy

View of building 11050 looking northeast, showing metal sided and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050 looking northeast, showing metal sided and roofed addition on east elevation. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Fire Station & Marine Barracks, D Street, at corner of 4th Street, China Lake, Kern County, CA

View of building 11050 looking northwest, with metal sided and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of building 11050 looking northwest, with metal sided and roofed addition on east elevation. - Naval Ordnance Test Station Inyokern, China Lake Pilot Plant, Fire Station & Marine Barracks, D Street, at corner of 4th Street, China Lake, Kern County, CA

40 CFR 438.1 - General applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... STANDARDS (CONTINUED) METAL PRODUCTS AND MACHINERY POINT SOURCE CATEGORY § 438.1 General applicability. (a..., or maintenance of metal parts, products, or machines for use in the Metal Product & Machinery (MP&M... Metal Products; Mobile Industrial Equipment; Motor Vehicle; Office Machine; Ordnance; Precious Metals...

40 CFR 438.1 - General applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... STANDARDS (CONTINUED) METAL PRODUCTS AND MACHINERY POINT SOURCE CATEGORY § 438.1 General applicability. (a..., or maintenance of metal parts, products, or machines for use in the Metal Product & Machinery (MP&M... Metal Products; Mobile Industrial Equipment; Motor Vehicle; Office Machine; Ordnance; Precious Metals...

40 CFR 438.1 - General applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... STANDARDS (CONTINUED) METAL PRODUCTS AND MACHINERY POINT SOURCE CATEGORY § 438.1 General applicability. (a..., or maintenance of metal parts, products, or machines for use in the Metal Product & Machinery (MP&M... Metal Products; Mobile Industrial Equipment; Motor Vehicle; Office Machine; Ordnance; Precious Metals...

Photographic copy of photograph (mid1950s, original print in possession of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph (mid-1950s, original print in possession of William Langer Jewel Bearing Plant, Rolla, North Dakota). VIEW OF PLANT, VIEW TO WEST. - Turtle Mountain Ordnance Plant, 213 First Street Northwest, Rolla, Rolette County, ND

Toxicological and chemical assessment of ordnance compounds in marine sediments and porewaters

USGS Publications Warehouse

Nipper, M.; Carr, R.S.; Biedenbach, J.M.; Hooten, R.L.; Miller, K.

2002-01-01

Toxicological and chemical studies were performed with a silty and a sandy marine sediment spiked with 2,6-dinitrotoluene (2,6-DNT), 2,4,6-trinitrophenylmethylnitramine (tetryl), or 2,4,6-trinitrophenol (picric acid). Whole sediment toxicity was analyzed by the 10-day survival test with the amphipod Ampelisca abdita, and porewater toxicity tests assessed macro-algae (Ulva fasciata) zoospore germination and germling growth, sea urchin (Arbacia punctulata) embryological development, and polychaete (Dinophilus gyrociliatus) survival and reproduction. Whole sediments spiked with 2,6-DNT were not toxic to amphipods. The fine-grained sediment spiked with tetryl was also not acutely toxic. The tetryl and picric acid LC50 values in the sandy sediment were 3.24 and 144 mg/kg dry weight, respectively. The fine-grained sediment spiked with picric acid generated a U-shaped concentration-response curve in the amphipod test, with increased survival both in the lowest and highest concentration. Grain-size distribution and organic carbon content strongly influenced the behavior of ordnance compounds in spiked sediments. Very low concentrations were measured in some of the treatments and irreversible binding and biodegradation are suggested as the processes responsible for the low measurements. Porewater toxicity varied with its sedimentary origin and with ordnance compound. The sea urchin embryological development test tended to be the least sensitive. Tetryl was the most toxic chemical in all porewater tests, and picric acid the least toxic. Samples spiked with 2,6-DNT contained a degradation product identified as 2-methyl-3-nitroaniline (also known as 2-amino-6-nitrotoluene), and unidentified peaks, possibly degradation products, were also seen in some of the picric acid- and tetryl-spiked samples. Degradation products may have played a role in observed toxicity. ?? 2002 Elsevier Science Ltd. All rights reserved.

Characterization of the fate and transport of nitroaromatic compounds at a former DoD ordnance depot site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klausmeier, M.E.; Yoon, J.

1999-07-01

The 975-acre Former Nansemond Ordnance Depot (FNOD) in Suffolk, Virginia was used by the Department of Defense (DoD) from 1917 until the mid-1950's for preparation, storage, transportation, inspection and demilitarization of many classes of ammunition and ordnance. Approximately 28 areas of Concern (AOC) have been identified by the EPA as areas that could pose potential risk to human health or the environment. The primary contaminants of concern are some trace metals and explosive compounds. During a summer 1987 field investigation, a slab of crystalline TNT was found which was estimated to weigh several tons. An enhanced MODFLOW model is beingmore » used to identify subsurface flow patterns. The calibrated model will be used to identify contaminant fate and transport behavior at the site. Enhancements to the MODFLOW model include an updated block-centered flow package (BCF4) and an updated recharge-seepage face boundary package (RSF4) to utilize for the FNOD site flow characterization. BCF4 package accurately delineates the water table without relying on an ad hoc rewetting procedure. This is accomplished by calculating the hydraulic head value required to transmit recharging water through the unsaturated zone without inactivating dry cells. The recharge-seepage face package eliminates the projection of heads above the ground surface by adjusting recharge to a cell when a user supplied ponding depth is reached. Using a regional model, a telescoping grid refinement technique was implemented to calculate the boundary conditions around the area of interest and to model quantity and quality interactions between surface and subsurface water regimes in a realistic manner.« less

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

ESTCP UXO Discrimination Study. MTADS Demonstration at Camp Sibert Magnetometer / EM61 MkII / GEM-3 Arrays, Gadsden, AL, April 2007

DTIC Science & Technology

2008-08-21

Yuma Proving Ground Open Field ............................................................................... 76 B.3.1 Response Stage... Yuma Proving Ground ZIP (250) Iomega ZIP disk (250 MB version) xv ACKNOWLEDGEMENTS Glenn Harbaugh and Daniel Steinhurst (P.I.) of Nova Research...sites at Aberdeen Proving Ground and Yuma Proving Ground in 2003 and 2004 [6]. At each of the sites, the Calibration Lanes, the Blind Test Grid

Standardized UXO Technology Demonstration Site Scoring Record No. 945

DTIC Science & Technology

2017-07-01

DISTRIBUTION LIST ATEC Project No. 2011-DT-ATC-DODSP-F0292 Note: A copy of this test report has been posted to the Versatile Information Systems...Directorate July 2017 Report Produced by: U.S. Army Aberdeen Test Center Aberdeen Proving Ground, MD 21005-5059 Report Produced for: Strategic...U.S. Army Test and Evaluation Command Aberdeen Proving Ground, MD 21005-5001 Distribution Unlimited, July 2017. The use of a trade name or the

Standardized UXO Technology Demonstration Site Open Field Scoring Record No. 908

DTIC Science & Technology

2008-08-01

demonstration at Aberdeen Proving Ground, a system with eight fluxgate magnetometers (Foerster CON650 gradiometers) and RTK-DGPS georeferencing will...be used. The spacing between the individual fluxgate sensors will be 25 cm (ca. 10 inches), totaling to a swath width of 2 m. c. The MAGNETO...MX system consists of: the MX-compact hardware multiplexer electronic module, up to 32 fluxgate gradiometers (for the APG demonstration: 8 fluxgate

Next Generation HeliMag UXO Mapping Technology

DTIC Science & Technology

2009-10-01

fluxgate magnetometer is used to allow for aeromagnetic compensation of the data as well as to provide redundant attitude information. 2.1.4 Telemetry...sensor operator from the helicopter. Based on a survey design study , the number of magnetometers was increased from 7 to 13, decreasing the across... magnetometers on a Kevlar reinforced boom mounted on a Bell 206L helicopter. The objectives of this demonstration were too:  Improve data acquisition speeds

The MTA UXO Survey and Target Recovery on Lake Erie at the Former Erie Army Depot

DTIC Science & Technology

2009-12-01

MTA Demonstration Front Matter ii FIGURES 1. Firing fans and target locations for Erie Army Depot in 1965...triangles at the base of the image show the locations of the 15 fixed firing positions that were used for proof firing projectiles...the marshland adjacent to the firing ranges, and along beaches fronting the former Depot, (Reference 2, Appendices B and J).3-5 The impact areas

Standardized UXO Technology Demonstration Site Woods Scoring Record Number 636 (Blackhawk Geoservices)

DTIC Science & Technology

2005-07-01

25 SECTION 5. ON-SITE LABOR COSTS SECTION 6. COMPARISON OF RESULTS TO OPEN FIELD DEMONSTRATION 6.1 SUMMARY OF RESULTS FROM OPEN...included for the purposes of calculating labor costs (section 5) except for downtime due to Demonstration Site issues. Demonstration Site issues, while noted...in the Daily Log, are considered non-chargeable downtime for the purposes of calculating labor costs and are not discussed. Breaks and lunches are

Next Generation Data Collection System for One-Pass Detection and Discrimination

DTIC Science & Technology

2011-12-01

ANSI Std Z39-18 OPTEMA demonstration at YPG ESTCP MM-0908 i December 2011 TABLE OF CONTENTS 1.0 INTRODUCTION ...OPTEMA demonstration at YPG ESTCP MM-0908 1 December 2011 1.0 INTRODUCTION 1.1 BACKGROUND The prohibitive costs of excavating all geophysical...an escort. After getting security passes and watching a safety video we drive to the UXO test-site where Kerry takes over as escort. Spend

UXO Discrimination Study Former Spencer Artillery Range

DTIC Science & Technology

2013-04-01

tested . This approach uses one of three models labeled: aggressive, intermediate and conservative. The choice of model depends on an a...anomalies will be selected for labeling using NMAL. The goal at this step is to maximize the information gain from new labels requested from the set of ...number of false alarms (nFA) is lower for the classifier where feature selection was used . 9 Complexity of a site is measured using an information

Cyclic Dinitroureas As Self-Remediating Munition Charges

DTIC Science & Technology

2009-02-26

Octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine NAWCWD Naval Air Warfare Center Weapons Division NMR Nuclear magnetic resonance PBXN Plastic Bonded...problems as UXO. A typical submunition fill, such as PBXN -107 in the BLU- 97/B, employs RDX as the main explosive charge. RDX is known to exhibit... 106 ; “maximum lambda” 1050; “lambda factor” 10. Results and Accomplishments As kinetic runs under the various conditions of humidity and soil

Detection of Buried Targets via Active Selection of Labeled Data: Application to Sensing Subsurface UXO

DTIC Science & Technology

2007-06-01

images,” IEEE Trans. Pattern Analysis Machine Intelligence, vol. 13, no. 2, pp. 99–113, 1991. [15] C. Bouman and M. Shapiro, “A multiscale random...including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing...this project was on developing new statistical algorithms for analysis of electromagnetic induction (EMI) and magnetometer data measured at actual

Shallow Water Marine UXO Detection Survey, United States Marine Corps Base, Camp Lejeune, North Carolina

DTIC Science & Technology

2011-04-01

resolution time-domain EM metal detector that is capable of detecting both ferrous and nonferrous metallic objects. The EM61 consists of air-cored...modifications to the Geonics EM61 metal detector . Modifications include higher transmitter power and frequency, faster sampling rates, and flexible...towed array (UUTA) electromagnetic system designed by 3Dgeophysics.com (3Dg) utilizes modified and improved Geonics, Ltd. electromagnetic (EM)61 metal

Standardized UXO Technology Demonstration Site, Open Field Scoring Record No. 893

DTIC Science & Technology

2008-07-01

EM) AMOS metal detector is a linear multichannel sensor array consisting of a 2-meter-wide transmitter coil and 16 receiver coils, mounted on a...ferrous and nonferrous metals : Will detect ammunition components 20-mm caliber and over at depths of up to 0.4 meter and ammunition components 100...robust, all-terrain trailer (fig. 1). b. The AMOS detector unit consists of the following main components: (1) Lower sensor level (dimensions

Standardized UXO Technology Demonstration Site, Blind Grid Scoring Record No. 919

DTIC Science & Technology

2008-07-01

provided by demonstrator) a. The core component of the electromagnetic (EM) AMOS metal detector is a linear multichannel sensor array consisting of a...Attainable accuracy of depth (z) +0.3 m h. Detection performance for ferrous and nonferrous metals : Will detect ammunition components 20-mm caliber...2-meter-wide transmitter coil and 16 receiver coils, mounted on a robust, all-terrain trailer (fig. 1). b. The AMOS detector unit consists of the

Standardized UXO Technology Demonstration Site, Blind Grid Scoring Record Number 842

DTIC Science & Technology

2007-06-01

collection sessions. Daily: A location identified as having no subsurface metal will be designated as a calibration point. Readings will be... metallic item will be placed below the center of the sensors, and the instrument’s response will be observed. The item will then be removed, and static... nonferrous anomalies. Due to limitations of the magnetometer, the nonferrous items cannot be detected. Therefore, the ROC curves presented in Figures

An Advanced ESTCP PELAN System for Surface and Near-surface UXO Discrimination

DTIC Science & Technology

2009-03-01

system was designed and assembled at SAIC. Test slugs representing 30mm to 105mm shells were constructed and filled with inert materials and explosives...results and system design, ESTCP decided to discontinue the effort before the prototype was constructed and demonstrated. iii TABLE OF CONTENTS...RDX and non-explosive plasticizers ) cps counts per second CW Chemical Warfare agent d-T deuterium-tritium DoD Department of Defense DOE

Standardized UXO Technology Demonstration Site, Scoring Record No. 943

DTIC Science & Technology

2014-08-01

COLLERAN ROAD ABERDEEN PROVING GROUND, MARYLAND 21005-5059 Printed on Recycled Paper TEDT-AT-SL-M MEMORANDUM FOR Program Manager – SERDP...equipment. Small munitions grid Contains 300 grid cells . The center of each grid cell contains either munitions, clutter, or nothing with a portion...weather was warm and the field dry throughout the survey period for Battelle. 12 3.3.3 Soil Moisture Three soil probes were placed at various