14 CFR Sec. 1-7 - Interpretation of accounts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS General Accounting Provisions Sec. 1-7 Interpretation of accounts. To the end that uniform accounting may be maintained, questions involving matters of accounting significance which are not clearly provided...

Numerical and Physical Modelling of Bubbly Flow Phenomena - Final Report to the Department of Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrea Prosperetti

This report describes the main features of the results obtained in the course of this project. A new approach to the systematic development of closure relations for the averaged equations of disperse multiphase flow is outlined. The focus of the project is on spatially non-uniform systems and several aspects in which such systems differ from uniform ones are described. Then, the procedure used in deriving the closure relations is given and some explicit results shown. The report also contains a list of publications supported by this grant and a list of the persons involved in the work.

14 CFR 25 - Traffic and Capacity Elements

Code of Federal Regulations, 2012 CFR

2012-01-01

... PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS... forth in section 19—Uniform Classification of Operating Statistics. (b) Carriers submitting Schedule T-100 shall use magnetic computer tape or IBM compatible disk for transmitting the prescribed data to...

14 CFR Section 25 - Traffic and Capacity Elements

Code of Federal Regulations, 2013 CFR

2013-01-01

... PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS... forth in section 19—Uniform Classification of Operating Statistics. (b) Carriers submitting Schedule T-100 shall use magnetic computer tape or IBM compatible disk for transmitting the prescribed data to...

Taking a Step Forward in Public Health Finance: Establishing Standards for a Uniform Chart of Accounts Crosswalk.

PubMed

Honoré, Peggy A; Leider, Jonathon P; Singletary, Vivian; Ross, David A

2015-01-01

In its 2012 report on the current and future states of public health finance, the Institute of Medicine noted, with concern, the relative lack of capacity for practitioners and researchers alike to make comparisons between health department expenditures across the country. This is due in part to different accounting systems, service portfolios, and state- or agency-specific reporting requirements. The Institute of Medicine called for a uniform chart of accounts, perhaps building on existing efforts such as the Public Health Uniform National Data Systems (PHUND$). Shortly thereafter, a group was convened to work with public health practitioners and researchers to develop a uniform chart of accounts crosswalk. A year-long process was undertaken to create the crosswalk. This commentary discusses that process, challenges encountered along the way and provides a draft crosswalk in line with the Foundational Public Health Services model that, if used by health departments, could allow for meaningful comparisons between agencies.

Role of Cytokines and Neurotrophins in the Central Nervous System in Venezuelan Equine Encephalitis Virus Pathogenesis

DTIC Science & Technology

2001-01-01

copyright owner, and will save and hold harmless the Uniformed Services University of the Health Sciences from any damage which may arise from such a...copyright violation. Kristen M. K. Catlin Department of Microbiology and Immunology Uniformed Services University of the Health Sciences Report...for reducing this burden, to Washington Headquarters Services , Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite

Project FARE Task IV Report: Urban Mass Transportation Industry Financial and Operating Data Reporting System. Volume I. Task and Project Summary.

DOT National Transportation Integrated Search

1973-11-01

The report contains a description of the uniform reporting system for the urban mass transit industry designed and tested in Project FARE. It is presented in five volumes. Volume I contains a description of how Task IV was accomplished and the conclu...

Project FARE task III report : urban mass transportation industry reporting system design : interim task III report for November 1972-June 1973 period. Part I - Task summary.

DOT National Transportation Integrated Search

1973-06-01

This report contains a description of the proposed uniform reporting system for the urban mass transit industry. It is presented in four volumes: Part I - Task Summary contains a description of how Task III was accomplished and the conclusions and re...

Who Are the Owners of Firearms Used in Adolescent Suicides?

ERIC Educational Resources Information Center

Johnson, Renee M.; Barber, Catherine; Azrael, Deborah; Clark, David E.; Hemenway, David

2010-01-01

In this brief report, the source of firearms used in adolescent suicides was examined using data from the National Violent Injury Statistics System, the pilot to the CDC's National Violent Death Reporting System, a uniform reporting system for violent and firearm-related deaths. Data represent the 63 firearm suicides among youth (less than 18 yrs)…

Project FARE task III report : urban mass transportation industry reporting system design : interim task III report for November 1972-June 1973 period. Part IV - Commuter rail reporting.

DOT National Transportation Integrated Search

1973-06-01

This report contains a description of the proposed uniform reporting system for the urban mass transit industry. It is presented in four volumes: Part I - Task Summary contains a description of how Task III was accomplished and the conclusions and re...

Illinois Community College Board Uniform Accounting Procedures Manual.

ERIC Educational Resources Information Center

Illinois Community Coll. Board, Springfield.

This manual was designed to provide chief finance officers and other administrators with a summary of laws and policies that relate to Illinois public community colleges and to provide a uniform system for accounting, budgeting, auditing, and reporting in the state's community colleges. After chapter I describes the fiscal philosophies and…

14 CFR Sec. 2-4 - Accounting period.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Accounting period. Sec. 2-4 Section 2-4... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS General Accounting Provisions Sec. 2-4 Accounting period. (a) The accounting year of each air carrier subject to this Uniform...

46 CFR 403.100 - Applicability of system of accounts and reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

... accordance with the guidelines of the Generally Accepted Accounting Principles (GAAP) issued by the Financial Accounting Standards Board. These guidelines are available by writing to the Director, Great Lakes Pilotage... PILOTAGE UNIFORM ACCOUNTING SYSTEM General § 403.100 Applicability of system of accounts and reports. Each...

Wisconsin Elementary and Secondary School Accounting System Handbook.

ERIC Educational Resources Information Center

Nelson, C. Richard

This handbook is the basic accounting document for Wisconsin's public school systems; it presents the means to achieve uniformity in reporting on the efficacy of the Wisconsin Elementary and Secondary School Accounting System (WESSAS). Its purpose is to provide financial information that will promote reporting, auditing, interdistrict comparison,…

24 CFR 5.801 - Uniform financial reporting standards.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Uniform financial reporting... and Urban Development GENERAL HUD PROGRAM REQUIREMENTS; WAIVERS Uniform Financial Reporting Standards § 5.801 Uniform financial reporting standards. (a) Applicability. This subpart H implements uniform...

24 CFR 5.801 - Uniform financial reporting standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Uniform financial reporting... and Urban Development GENERAL HUD PROGRAM REQUIREMENTS; WAIVERS Uniform Financial Reporting Standards § 5.801 Uniform financial reporting standards. (a) Applicability. This subpart H implements uniform...

75 FR 63824 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-18

.... 922, Brady Handgun Violence Prevention Act; 28 U.S.C. 534, Uniform Federal Crime Reporting Act; 42 U.S....'' * * * * * Storage: Delete entry and replace with ``Paper records and electronic storage media.'' Retrievability... (DIBRS); 18 U.S.C. 922, Brady Handgun Violence Prevention Act; 28 U.S.C. 534, Uniform Federal Crime...

75 FR 71092 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-22

... (DIBRS); 18 U.S.C. 922 note, The Brady Handgun Violence Prevention Act; 28 U.S.C. 534 note, Uniform...: Delete entry and replace with ``Electronic storage media and file folders.'' Retrievability: Delete entry..., The Brady Handgun Violence Prevention Act; 28 U.S.C. 534 note, Uniform Federal Crime Reporting Act; 42...

Gravitational Influences on Flame Propagation through Non-Uniform, Premixed Gas Systems

NASA Technical Reports Server (NTRS)

Miller, Fletcher J.; Easton, John; Ross, Howard D.; Marchese, Anthony; Perry, David; Kulis, Michael

2001-01-01

Flame propagation through non-uniformly premixed (or layered) gases has importance both in useful combustion systems and in unintentional fires. As summarized previously, non-uniform premixed gas combustion receives scant attention compared to the more usual limiting cases of diffusion or uniformly premixed flames, especially regarding the role gravity plays. This paper summarizes our progress on furthering the knowledge of layered combustion, in which a fuel concentration gradient exists normal to the direction of flame spread. We present experimental and numerical results for flame spread through propanol-air layers formed near the flash point temperature (25 C) or near the stoichiometric temperature (33 C). Both the model and experimental results show that the removal of gravity results in a faster spreading flame, by as much as 80% depending on conditions. This is exactly the opposite effect as that predicted by an earlier model reported. We also found that having a gallery lid results in faster flame spread, an effect more pronounced at normal gravity, demonstrating the importance of enclosure geometry. Also reported here is the beginning of our spectroscopic measurements of fuel vapor.

46 CFR 403.300 - Financial reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Financial reporting requirements. 403.300 Section 403.300 Shipping COAST GUARD (GREAT LAKES PILOTAGE), DEPARTMENT OF HOMELAND SECURITY GREAT LAKES PILOTAGE UNIFORM ACCOUNTING SYSTEM Reporting Requirements § 403.300 Financial reporting requirements. (a) General...

46 CFR 403.300 - Financial reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 8 2011-10-01 2011-10-01 false Financial reporting requirements. 403.300 Section 403... UNIFORM ACCOUNTING SYSTEM Reporting Requirements § 403.300 Financial reporting requirements. (a) General: (1) The financial statements shall list each active account, including subsidiary accounts. (2) The...

Development of uniform sections for pavement management system inventory and application : interim report.

DOT National Transportation Integrated Search

2007-12-01

This report summarizes the findings of the first phase of LTRC research project 04-2P, which is sponsored by LADOTD. The project is assessing the current status and the state-of-the-practice of the LADOTD pavement management system (PMS). Results of ...

Project FARE task II report : urban mass transportation industry survey of reporting capability : interim task II report for July-November 1972 period

DOT National Transportation Integrated Search

1972-11-01

Report contains a description of the work done to evaluate the capability of the urban mass transit industry to report financial and operating data through a uniform reporting system. Techniques used in the evaluation included a questionnaire survey ...

Summary Report: Uniform Traffic Control And Warning Messages For Portable Changeable Message Signs

DOT National Transportation Integrated Search

2000-03-01

The California database incorporated in the Highway Safety Information System (HSIS) is derived from the California TASAS (Traffic Accident Surveillance and Analysis System). The system, maintained by the Traffic Operations Office of Caltrans, is a m...

14 CFR Sec. 1-8 - Address for reports and correspondence.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS General Accounting Provisions Sec. 1-8 Address for reports and correspondence. All... Information, K-25, U.S. Department of Transportation, 1200 New Jersey Avenue, SE., Washington, DC 20590...

Computerized Financial Reporting Based on GAAP.

ERIC Educational Resources Information Center

Tikkanen, Stan; Liljeberg, Burt

1983-01-01

Describes the statewide computerized system developed in Minnesota following the 1976 enactment of the Uniform Financial Accounting and Reporting Standards (UFARS) law. UFARS includes provisions for an advisory council responsible for recommending accounting and reporting procedures, and seven data processing centers to serve all 560 Minnesota…

A Low-Voltage and High Uniformity Nano-Electro-Mechanical System Tunable Color Filter Based on Subwavelength Grating

NASA Astrophysics Data System (ADS)

Honma, Hiroaki; Takahashi, Kazuhiro; Ishida, Makoto; Sawada, Kazuaki

2012-11-01

This paper reports on the construction of a nano-electro-mechanical system (NEMS) tunable color filter based on a subwavelength grating with high color uniformity and a low drive voltage. We recently proposed a ground-voltage-ground (GVG)-type tunable color filter with a parallel-plate actuator with three pairs of electrodes to decrease the crosstalk due to the electrostatic attractive force between each pair of actuators. Our finite element method (FEM) simulation results indicate that the drive voltage is decreased by 10 V, as compared to that of the previously reported GV type. The proposed structure was fabricated using a silicon-on-insulator (SOI) wafer. The color tuning capability of the device was demonstrated by applying a drive voltage of 6.7 V. The reflected light intensity was decreased by 34% at a wavelength of 680 nm. Color uniformity was also obtained in the filter area by reducing the variation of the displacement on the one-dimensional actuator arrays.

Reporting Manual for Florida Community Colleges.

ERIC Educational Resources Information Center

Florida State Board of Community Colleges, Tallahassee.

Uniform procedures, terminology, definitions, forms, and instructions are presented to aid individual Florida community colleges in completing state reporting requirements. Following introductory information concerning the Community College Management Information System (CCMIS) the manual explains the purpose and characteristics of the Community…

A global, comprehensive review of literature related to paper recycling: A pressing need for a uniform system of terms and definitions.

PubMed

Ervasti, Ilpo; Miranda, Ruben; Kauranen, Ilkka

2016-02-01

A global, comprehensive review of terms and definitions related to paper recycling was conducted in this article. Terms and definitions related to paper recycling have varied in the course of time. Different terms and different definitions for the same thing are being used in different geographical regions and by different organizations. Definitions are different based on varying conceptions of waste paper as a raw material. Definitions of how to make various calculations related to paper recycling activity are inconsistent. Even such fundamental basic definitions like how to calculate recycling rate and paper consumption are not uniform. It could be concluded that there is no uniform system of terms and definitions related to paper recycling and the implications of this deficiency are profound. For example, it is difficult to reliably compare with each other statistics from different times and from different geographical regions. It is not possible to measure if targets for recycling activities are met if the terms describing the targets are not uniformly defined. In cases of reporting data for recycling targets, the lack of uniform terminology can, for example, impede the necessary transparency between different stakeholders and may allow for deception. The authors conclude there is a pressing need to develop a uniform system of terms and definition for terms related to paper recycling. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of the seafloor displacement from uniform and non-uniform slip models on tsunami simulation of the 2011 Tohoku-Oki earthquake

NASA Astrophysics Data System (ADS)

Ulutas, Ergin

2013-01-01

The numerical simulations of recent tsunami caused by 11 March 2011 off-shore Pacific coast of Tohoku-Oki earthquake (Mw 9.0) using diverse co-seismic source models have been performed. Co-seismic source models proposed by various observational agencies and scholars are further used to elucidate the effects of uniform and non-uniform slip models on tsunami generation and propagation stages. Non-linear shallow water equations are solved with a finite difference scheme, using a computational grid with different cell sizes over GEBCO30 bathymetry data. Overall results obtained and reported by various tsunami simulation models are compared together with the available real-time kinematic global positioning system (RTK-GPS) buoys, cabled deep ocean-bottom pressure gauges (OBPG), and Deep-ocean Assessment and Reporting of Tsunami (DART) buoys. The purpose of this study is to provide a brief overview of major differences between point-source and finite-fault methodologies on generation and simulation of tsunamis. Tests of the assumptions of uniform and non-uniform slip models designate that the average uniform slip models may be used for the tsunami simulations off-shore, and far from the source region. Nevertheless, the heterogeneities of the slip distribution within the fault plane are substantial for the wave amplitude in the near field which should be investigated further.

47 CFR 32.19 - Address for reports and correspondence.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Address for reports and correspondence. 32.19 Section 32.19 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES General Instructions § 32.19 Address for...

47 CFR 32.19 - Address for reports and correspondence.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Address for reports and correspondence. 32.19 Section 32.19 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES General Instructions § 32.19 Address for...

47 CFR 32.19 - Address for reports and correspondence.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Address for reports and correspondence. 32.19 Section 32.19 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES General Instructions § 32.19 Address for...

East Europe Report.

DTIC Science & Technology

1987-01-23

111100 JPRS-EER-87-010 23 JANUARY 1987 East Europe Report r\\3 en FBIS FOREIGN BROADCAST INFORMATION SERVICE REPRODUCED^ARTMENT OF COMMERCE...and Solutions In tnfComprehensive Intensification and Modernisation of the GDR s Uniform Socialist Transport System " (Slightly shortened version of...I. Status, Tasks and Responsibility of the Transport System in the GDR’s Developed Socialist Society With the further shaping of the developed

Colorectal cancer and the 7th revision of the TNM staging system: review of changes and suggestions for uniform pathologic reporting.

PubMed

Obrocea, F L; Sajin, Maria; Marinescu, Elena Cristina; Stoica, D

2011-01-01

Colorectal cancer (CRC) is a neoplastic disease with a continuously growing incidence in Romania and throughout the world. Although the surgery remains the first line treatment for most of the cases, newly discovered targeted molecular therapies - effective for some patients, but with various side effects and significant financial burden for the national health systems - requires not only stratification of patients in prognostic groups but also evaluation of some non-anatomic factors with major impact on the prognosis and therapeutic strategy. The AJCC/UICC TNM staging system, in his 7th revision, effective for cases diagnosed on or after January 1, 2010, responds to these needs. On the other hand, the role of the pathologist is increasing in terms of workload and amount of information to be included in the pathology report in order to deliver a personalized diagnosis. There are concerns worldwide regarding relevance, validity and completeness of pathologic reporting of CRC in the absence of a uniform reporting format. Therefore, suggestions for a standardized pathology report of CRC are made, based on TNM 7 and recent, up-to-date conclusive published data.

14 CFR Sec. 19-6 - Public disclosure of traffic data.

Code of Federal Regulations, 2014 CFR

2014-01-01

... PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS..., shall be publicly available immediately following the Department's determination that the database is...

Ultra-thin carbon-fiber paper fabrication and carbon-fiber distribution homogeneity evaluation method

NASA Astrophysics Data System (ADS)

Zhang, L. F.; Chen, D. Y.; Wang, Q.; Li, H.; Zhao, Z. G.

2018-01-01

A preparation technology of ultra-thin Carbon-fiber paper is reported. Carbon fiber distribution homogeneity has a great influence on the properties of ultra-thin Carbon-fiber paper. In this paper, a self-developed homogeneity analysis system is introduced to assist users to evaluate the distribution homogeneity of Carbon fiber among two or more two-value images of carbon-fiber paper. A relative-uniformity factor W/H is introduced. The experimental results show that the smaller the W/H factor, the higher uniformity of the distribution of Carbon fiber is. The new uniformity-evaluation method provides a practical and reliable tool for analyzing homogeneity of materials.

Task reports on developing techniques for scattering by 3D composite structures and to generate new solutions in diffraction theory using higher order boundary conditions

NASA Technical Reports Server (NTRS)

Volakis, John L.

1991-01-01

There are two tasks described in this report. First, an extension of a two dimensional formulation is presented for a three dimensional body of revolution. A Fourier series expansion of the vector electric and magnetic fields is employed to reduce the dimensionality of the system, and an exact boundary condition is employed to terminate the mesh. The mesh termination boundary is chosen such that it leads to convolutional boundary operators for low O(n) memory demand. Second, rigorous uniform geometrical theory of diffraction (UTD) diffraction coefficients are presented for a coated convex cylinder simulated with generalized impedance boundary conditions. Ray solutions are obtained which remain valid in the transition region and reduce uniformly those in the deep lit and shadow regions. A uniform asymptotic solution is also presented for observations in the close vicinity of the cylinder.

34 CFR 200.8 - Assessment reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... assessment is given; (ii) In an understandable and uniform format, including an alternative format (e.g... understand. (b) Itemized score analyses for LEAs and schools. (1) A State's academic assessment system must produce and report to LEAs and schools itemized score analyses, consistent with § 200.2(b)(4), so that...

34 CFR 200.8 - Assessment reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... assessment is given; (ii) In an understandable and uniform format, including an alternative format (e.g... understand. (b) Itemized score analyses for LEAs and schools. (1) A State's academic assessment system must produce and report to LEAs and schools itemized score analyses, consistent with § 200.2(b)(4), so that...

34 CFR 200.8 - Assessment reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... assessment is given; (ii) In an understandable and uniform format, including an alternative format (e.g... understand. (b) Itemized score analyses for LEAs and schools. (1) A State's academic assessment system must produce and report to LEAs and schools itemized score analyses, consistent with § 200.2(b)(4), so that...

34 CFR 200.8 - Assessment reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... assessment is given; (ii) In an understandable and uniform format, including an alternative format (e.g... understand. (b) Itemized score analyses for LEAs and schools. (1) A State's academic assessment system must produce and report to LEAs and schools itemized score analyses, consistent with § 200.2(b)(4), so that...

34 CFR 200.8 - Assessment reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... assessment is given; (ii) In an understandable and uniform format, including an alternative format (e.g... understand. (b) Itemized score analyses for LEAs and schools. (1) A State's academic assessment system must produce and report to LEAs and schools itemized score analyses, consistent with § 200.2(b)(4), so that...

41 CFR 101-26.800 - Scope of subpart.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Scope of subpart. 101-26... Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND... Scope of subpart. This subpart prescribes a uniform system for reporting discrepancies or deficiencies...

41 CFR 101-26.800 - Scope of subpart.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Scope of subpart. 101-26... Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND... Scope of subpart. This subpart prescribes a uniform system for reporting discrepancies or deficiencies...

41 CFR 101-26.800 - Scope of subpart.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Scope of subpart. 101-26... Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND... Scope of subpart. This subpart prescribes a uniform system for reporting discrepancies or deficiencies...

14 CFR Section 19-6 - Public disclosure of traffic data.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED... database is complete, but no earlier than six months after the date of the data. Military operations are...

14 CFR Section 19-6 - Public disclosure of traffic data.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED... database is complete, but no earlier than six months after the date of the data. Military operations are...

14 CFR 19-6 - Public disclosure of traffic data.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED... database is complete, but no earlier than six months after the date of the data. Military operations are...

14 CFR Section 19-6 - Public disclosure of traffic data.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED... database is complete, but no earlier than six months after the date of the data. Military operations are...

Morphology Modulation of Direct Inkjet Printing by Incorporating Polymers and Surfactants into a Sol-Gel Ink System.

PubMed

Zhu, Zhennan; Ning, Honglong; Cai, Wei; Wei, Jinglin; Zhou, Shangxiong; Yao, Rihui; Lu, Xubing; Zhang, Jianhua; Zhou, ZhongWei; Peng, Junbiao

2018-06-05

Many methods have been reported to prevent the nonuniformity of inkjet printing structures. Most of them depend on the balance of the capillary flow in the printing pattern during the evaporation of the solvent. However, as the relation of evaporation and capillary flow can obviously vary among different ink systems, it is difficult for a method to fit most of the situations. Therefore, it would be a promising way to eliminate any capillary flow before solvent evaporation so that morphology of the printing structure will not be affected by the evaporation behavior of the ink system. In this paper, a novel method of direct inkjet printing of a uniform metal oxide structure is reported. We introduce a polymer polyacrylamide and a surfactant FSO into a sol-gel ink system, and the new ink system can gel from the printing pattern edge to center as temperature increases because of the cross-linking of the polymer chains. By that means, transport of solute molecules and solvent molecules is limited. Meanwhile, the surfactant can ensure that the solute in the central liquid phase deposits uniformly by enhancing the Marangoni flow during the gelation process. The ZrO 2 film with uniform morphology was fabricated by drying and annealing the gelating film and afforded a leakage current density of 7.48 × 10 -7 A cm -2 at 1 MV and a breakdown field of 1.9 MV cm -1 at an annealing temperature of 250 °C.

42 CFR 137.205 - Will this voluntary uniform data set reporting activity be required of all Self-Governance Tribes...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Will this voluntary uniform data set reporting... Provisions Health Status Reports § 137.205 Will this voluntary uniform data set reporting activity be... resources, hardware, software, and technical assistance to the Self-Governance Tribes to facilitate data...

42 CFR 137.205 - Will this voluntary uniform data set reporting activity be required of all Self-Governance Tribes...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Will this voluntary uniform data set reporting... Provisions Health Status Reports § 137.205 Will this voluntary uniform data set reporting activity be... resources, hardware, software, and technical assistance to the Self-Governance Tribes to facilitate data...

42 CFR 137.205 - Will this voluntary uniform data set reporting activity be required of all Self-Governance Tribes...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Will this voluntary uniform data set reporting... Provisions Health Status Reports § 137.205 Will this voluntary uniform data set reporting activity be... resources, hardware, software, and technical assistance to the Self-Governance Tribes to facilitate data...

42 CFR 137.205 - Will this voluntary uniform data set reporting activity be required of all Self-Governance Tribes...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Will this voluntary uniform data set reporting... Provisions Health Status Reports § 137.205 Will this voluntary uniform data set reporting activity be... resources, hardware, software, and technical assistance to the Self-Governance Tribes to facilitate data...

Texas State Library Grant Management Handbook: A Procedures Manual to Uniform Grants and Contract Management Standards Based on Texas Civil Statutes, Article 4413 (32g) and the Common Rule for Uniform Administrative Requirements for Grants and Cooperative Agreements to State and Local Governments.

ERIC Educational Resources Information Center

Conable, Sharon R.

The purpose of this manual is to provide a conceptual framework of information concerning the reporting, financial, contractual, and auditing requirements for recipients of Texas State Library grants funded with state and federal funds under the Library Systems Act (LSA) and the Library Service and Construction Act (LSCA). The manual is divided…

Grant Management Handbook: A Procedures Manual to Uniform Grants and Contract Management Standards Based on Texas Civil Statutes, Article 4413 (32g) and the Common Rule for Uniform Administrative Requirements for Grants and Cooperative Agreements to State and Local Governments.

ERIC Educational Resources Information Center

Conable, Sharon R.

This manual provides a conceptual framework and reference source concerning the reporting, financial contractual, and auditing requirements for recipients of Texas State Library grants funded with state and federal funds under the Library Systems Act (LSA) and the Library Services and Construction Act (LSCA). The handbook is divided into 12…

Developing ratings for food products: lessons learned from media rating systems.

PubMed

Kunkel, Dale; McKinley, Christopher

2007-01-01

Children regularly consume low-nutrient, high-calorie food that is not consistent with a healthful diet, contributing to an increasing epidemic of overweight and obesity. Among the multiple causes of this problem is the food industry's emphasis on marketing calorie-dense food products to children. The Institute of Medicine (IOM) has recommended that industry adopt a uniform system of simplified food ratings to convey the nutritional qualities of food in a manner that is understandable and appealing to children and youth. This report analyzes the need for such a system in a food marketing environment that increasingly identifies healthful products for the consumer in inconsistent fashion. It considers evidence regarding current usage of food labeling and draws parallels with media rating systems in discussing the prospects for a uniform food rating system that would accomplish the IOM's objective.

Deterministic and Stochastic Analysis of a Prey-Dependent Predator-Prey System

ERIC Educational Resources Information Center

Maiti, Alakes; Samanta, G. P.

2005-01-01

This paper reports on studies of the deterministic and stochastic behaviours of a predator-prey system with prey-dependent response function. The first part of the paper deals with the deterministic analysis of uniform boundedness, permanence, stability and bifurcation. In the second part the reproductive and mortality factors of the prey and…

Vocational Training in the Federal Republic of Germany.

ERIC Educational Resources Information Center

Bednarz-Braun, Iris; And Others

1990-01-01

Reports on two studies about vocational training in the Federal Republic of Germany (FRG). Finds that there is no uniform system of vocational training, but there are distinct segments with different objectives and different quality. Predicts that the West German system of vocational training will experience a loss of effectiveness unless it…

Development of uniform standards for allowable lane closure : final report, September 2008.

DOT National Transportation Integrated Search

2008-09-01

Procedures for determining allowable lane closure hours to perform maintenance, construction, resurfacing, regional permit and major access permit work on the state highway system were evaluated. The current process involves the collection of traffic...

14 CFR 01 - Authority Under Which Accounting and Reporting Rules and Regulations are Prescribed and Administered

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Authority Under Which Accounting and... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 01 Authority... shall have authority under the orders of the Board to inspect and examine any and all such lands...

Quick-Reaction Report on the Audit of ReCoupment Actions on Medicine Payments to Uniformed Services Treatment Facilities.

DTIC Science & Technology

1993-07-21

OFFICE OF THE INSPECTOR GENERAL QUICK-REACTION REPORT ON THE AUDIT OF RECOUPMENT ACTIONS ON MEDICARE PAYMENTS TO UNIFORMED SERVICES TREATMENT...Quick-Reaction Report on the Audit of Recoupment Actions on Medicare Payments to Uniformed Services Treatment Facilities (Report No. 93-150) We are...Inspectors General will provide a joint report to the congressional committees that requested the audit . The courtesies extended to the audit staff

Solution pH change in non-uniform alternating current electric fields at frequencies above the electrode charging frequency

PubMed Central

An, Ran; Massa, Katherine

2014-01-01

AC Faradaic reactions have been reported as a mechanism inducing non-ideal phenomena such as flow reversal and cell deformation in electrokinetic microfluidic systems. Prior published work described experiments in parallel electrode arrays below the electrode charging frequency (fc), the frequency for electrical double layer charging at the electrode. However, 2D spatially non-uniform AC electric fields are required for applications such as in plane AC electroosmosis, AC electrothermal pumps, and dielectrophoresis. Many microscale experimental applications utilize AC frequencies around or above fc. In this work, a pH sensitive fluorescein sodium salt dye was used to detect [H+] as an indicator of Faradaic reactions in aqueous solutions within non-uniform AC electric fields. Comparison experiments with (a) parallel (2D uniform fields) electrodes and (b) organic media were employed to deduce the electrode charging mechanism at 5 kHz (1.5fc). Time dependency analysis illustrated that Faradaic reactions exist above the theoretically predicted electrode charging frequency. Spatial analysis showed [H+] varied spatially due to electric field non-uniformities and local pH changed at length scales greater than 50 μm away from the electrode surface. Thus, non-uniform AC fields yielded spatially varied pH gradients as a direct consequence of ion path length differences while uniform fields did not yield pH gradients; the latter is consistent with prior published data. Frequency dependence was examined from 5 kHz to 12 kHz at 5.5 Vpp potential, and voltage dependency was explored from 3.5 to 7.5 Vpp at 5 kHz. Results suggest that Faradaic reactions can still proceed within electrochemical systems in the absence of well-established electrical double layers. This work also illustrates that in microfluidic systems, spatial medium variations must be considered as a function of experiment time, initial medium conditions, electric signal potential, frequency, and spatial position. PMID:25553200

49 CFR Appendix B to Part 26 - Uniform Report of DBE Awards or Commitments and Payments Form

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 1 2013-10-01 2013-10-01 false Uniform Report of DBE Awards or Commitments and Payments Form B Appendix B to Part 26 Transportation Office of the Secretary of Transportation... PROGRAMS Pt. 26, App. B Appendix B to Part 26—Uniform Report of DBE Awards or Commitments and Payments Form...

Determination of Duty Cycle for Energy Storage Systems in a Renewables (Solar) Firming Application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schoenwald, David A.; Ellison, James

2016-04-01

This report supplements the document, “Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems,” issued in a revised version in April 2016, which will include the renewables (solar) firming application for an energy storage system (ESS). This report provides the background and documentation associated with the determination of a duty cycle for an ESS operated in a renewables (solar) firming application for the purpose of measuring and expressing ESS performance in accordance with the ESS performance protocol.

Project UCARE : Uniform Commuter Assistance Reporting and Evaluation for transportation demand management programs, [summary].

DOT National Transportation Integrated Search

2013-09-01

The federal transportation reauthorization called : Moving Ahead for Progress in the 21st Century Act : (MAP-21) creates a program that addresses many : challenges facing the U.S. transportation system. : These challenges include improving safety, : ...

Response, Emergency Staging, Communications, Uniform Management, and Evacuation (R.E.S.C.U.M.E.) : report on functional and performance requirements, and high-level data and communication needs.

DOT National Transportation Integrated Search

1995-06-01

INTELLIGENT VEHICLE INITIATIVE OR IVI ABSTRACT THE GOAL OF THE TRAVTEK CAMERA CAR STUDY WAS TO FURNISH A DETAILED EVALUATION OF DRIVING AND NAVIGATION PERFORMANCE, SYSTEM USABILITY, AND SAFETY FOR THE TRAVTEK SYSTEM. TO ACHIEVE THIS GOAL, AN INSTRUME...

Health information management: an introduction to disease classification and coding.

PubMed

Mony, Prem Kumar; Nagaraj, C

2007-01-01

Morbidity and mortality data constitute an important component of a health information system and their coding enables uniform data collation and analysis as well as meaningful comparisons between regions or countries. Strengthening the recording and reporting systems for health monitoring is a basic requirement for an efficient health information management system. Increased advocacy for and awareness of a uniform coding system together with adequate capacity building of physicians, coders and other allied health and information technology personnel would pave the way for a valid and reliable health information management system in India. The core requirements for the implementation of disease coding are: (i) support from national/institutional health administrators, (ii) widespread availability of the ICD-10 material for morbidity and mortality coding; (iii) enhanced human and financial resources; and (iv) optimal use of informatics. We describe the methodology of a disease classification and codification system as also its applications for developing and maintaining an effective health information management system for India.

Development of Uniform Sections for PMS Inventory and Application.

DOT National Transportation Integrated Search

2007-12-01

This report summarizes the findings of the first phase of LTRC research project 04-2P, which is sponsored by LADOTD. : The project is assessing the current status and the state-of-the-practice of the LADOTD pavement management system : (PMS). Results...

Optimized Baking of the DIII-D Vessel

DOE Office of Scientific and Technical Information (OSTI.GOV)

P.M. Anderson; A.G. Kellman

The DIII-D tokamak vacuum vessel baking system is used to heat the vessel walls and internal hardware to an average temperature of 350 C to allow rapid conditioning of the vacuum surfaces. The system combines inductive heating and a circulating hot air system to provide rapid heating with temperature uniformity required by stress considerations. In recent years, the time to reach 350 C had increased from 9 hrs to 14 hrs. To understand and remedy this sluggish heating rate, an evaluation of the baking system was recently performed. The evaluation indicated that the mass of additional in-vessel hardware (50% increasemore » in mass) was primarily responsible. This paper reports on this analysis and the results of the addition of an electric air heater and procedural changes that have been implemented. Preliminary results indicate that the time to 350 C has been decreased to 4.5 hours and the temperature uniformity has improved.« less

Image correlation microscopy for uniform illumination.

PubMed

Gaborski, T R; Sealander, M N; Ehrenberg, M; Waugh, R E; McGrath, J L

2010-01-01

Image cross-correlation microscopy is a technique that quantifies the motion of fluorescent features in an image by measuring the temporal autocorrelation function decay in a time-lapse image sequence. Image cross-correlation microscopy has traditionally employed laser-scanning microscopes because the technique emerged as an extension of laser-based fluorescence correlation spectroscopy. In this work, we show that image correlation can also be used to measure fluorescence dynamics in uniform illumination or wide-field imaging systems and we call our new approach uniform illumination image correlation microscopy. Wide-field microscopy is not only a simpler, less expensive imaging modality, but it offers the capability of greater temporal resolution over laser-scanning systems. In traditional laser-scanning image cross-correlation microscopy, lateral mobility is calculated from the temporal de-correlation of an image, where the characteristic length is the illuminating laser beam width. In wide-field microscopy, the diffusion length is defined by the feature size using the spatial autocorrelation function. Correlation function decay in time occurs as an object diffuses from its original position. We show that theoretical and simulated comparisons between Gaussian and uniform features indicate the temporal autocorrelation function depends strongly on particle size and not particle shape. In this report, we establish the relationships between the spatial autocorrelation function feature size, temporal autocorrelation function characteristic time and the diffusion coefficient for uniform illumination image correlation microscopy using analytical, Monte Carlo and experimental validation with particle tracking algorithms. Additionally, we demonstrate uniform illumination image correlation microscopy analysis of adhesion molecule domain aggregation and diffusion on the surface of human neutrophils.

ADP Systems: Examination of Non-Federal Hospital Information Systems.

DTIC Science & Technology

1987-06-30

administrative and business management, and other purposes, such as research . In 1980, we reported1 that integrated hospital information systems evolved...Defense’s (DOD) and Veterans Administration’s (VA) efforts to develop and implement systems for federal hospitals. We used two methods to derive the...integrated in that they supported a variety of hospital activities and a uniform set of data access methods . The hospitals in our survey indicated that

[Better communication between surgery and anesthesia may provide safer surgery. The exchange of information has been mapped within the framework of "Safe abdominal surgery"].

PubMed

Göransson, Katarina; Lundberg, Johan; Ljungqvist, Olle; Ohlsson, Elisabet; Sandblom, Gabriel

2015-09-01

Poor communication between surgical and anesthesia unit personnel may jeopardize patient safety.  Review reports from a national survey on patient safety performed at 17 units 2011-2013 were analyzed in order to identify strategies to reduce risks related to the interaction between surgery and anesthesia. The reports were reviewed in this study by an independent group in order to extract findings related to communication between anesthesia and surgical unit personnel. Suggested strategies to improve patient safety included: uniform national health declaration forms; consistent use of admission notes; uniform systems for documenting medical information; multidisciplinary forum for evaluation of high-risk patients; weekly and daily scheduling of surgical programs; application of the WHO check list; open dialog during surgery; oral and written reports from the surgeon to the postoperative unit; and combined mortality and morbidity conferences.

Prototype development and demonstration for response, emergency staging, communications, uniform management, and evacuation (R.E.S.C.U.M.E.) : R.E.S.C.U.M.E. prototype system architecture.

DOT National Transportation Integrated Search

2014-01-01

This document provides the high-level system architecture for the Prototype Development and Demonstration of a R.E.S.C.U.M.E. system. The requirements addressed in this document are based upon those that can be found in previous R.E.S.C.U.M.E. report...

Report on METHODS OF Evaluating Students at the University of California, Berkeley.

ERIC Educational Resources Information Center

Miller, Stuart

Several arguments are made for changing the present system of grading in college. The arguments deal with: (1) the negative effect of grading on the teaching situation--the system is capricious and variable and encourages "grade grubbing"; (2) the lack of accuracy and uniformity of grades; (3) the effect of grading, as an enforcer of the…

A Study of a Two Stage Maximum Power Point Tracking Control of a Photovoltaic System under Partially Shaded Insolation Conditions

NASA Astrophysics Data System (ADS)

Kobayashi, Kenji; Takano, Ichiro; Sawada, Yoshio

A photovoltaic array shows relatively low output power density, and has a greatly drooping Current-Voltage (I-V) characteristic. Therefore, Maximum Power Point Tracking (MPPT) control is used to maximize the output power of the array. Many papers have been reported in relation to MPPT. However, the Current-Power (I-P) curve sometimes shows multi-local maximum points mode under non-uniform insolation conditions. The operating point of the PV system tends to converge to a local maximum output point which is not the real maximal output point on the I-P curve. Some papers have been also reported, trying to avoid this difficulty. However most of those control systems become rather complicated. Then, the two stage MPPT control method is proposed in this paper to realize a relatively simple control system which can track the real maximum power point even under non-uniform insolation conditions. The feasibility of this control concept is confirmed for steady insolation as well as for rapidly changing insolation by simulation study using software PSIM and LabVIEW. In addition, simulated experiment confirms fundament al operation of the two stage MPPT control.

14 CFR Section 8 - General

Code of Federal Regulations, 2011 CFR

2011-01-01

... UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Profit and Loss Classification Section 8 General (a) The profit and loss accounts are designed to reflect, through natural groupings, the... the dual subdivision of profit and loss elements in terms of both natural objectives and functional...

14 CFR 5 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false [Reserved] Section 5 Section Section 5 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Balance Sheet Classifications Section 5 [Reserved...

Human Capital: DoD Compliance With the Uniformed and Overseas Citizens Absentee Voting Act

DTIC Science & Technology

2003-03-31

UVAOs to perform their duties: “last day to mail” notifications to uniformed absentee voters; access to information regarding voter registration...the scope of our research on absentee voting issues that were brought to our attention by uniformed absentee voters. We performed this evaluation...and Overseas Citizens Absentee Voting Act (D-2003-072) Report Documentation Page Report Date 31 Mar 2003 Report Type N/A Dates Covered (from... to

Assessment and improvement of the Italian healthcare system: first evidence from a pilot national performance evaluation system.

PubMed

Nuti, Sabina; Seghieri, Chiara; Vainieri, Milena; Zett, Silvia

2012-01-01

The Italian National Health System (NHS), established in 1978, follows a model similar to the Beveridge model developed by the British NHS (Beveridge 1942; Musgrove 2000). Like the British NHS, healthcare coverage for the Italian population is provided and financed by the government through taxes. Universal coverage provides uniform healthcare access to citizens and is the characteristic usually considered the added value of a welfare system financed by tax revenues. Nonetheless, in Italy the strong policy of decentralization, which has been taking place since the early 1990s, has gradually shifted powers from the state to the 21 Italian regions. Consequently, the state now retains limited supervisory control and continues to have overall responsibility for the NHS in order to ensure uniform and essential levels of health services across the country. In this context, it has become essential, both for the ministry and for regions, to adopt a common performance evaluation system (PES). This article reports the definition, implementation, and first evidences of a pilot PES at a national level. It shows how this PES can be viewed as a strategic tool supporting the Ministry of Health (MoH) in ensuring uniform levels of care for the population and assisting regional managers to evaluate performance in benchmarking. Finally, lessons for other health systems, based on the Italian experience, are provided.

Data Needs in Vocational Education. "The Development of a Minimal Information System to Satisfy the Needs of Selected User Groups." Final Report. Volume III. Project EDNEED Lexicon.

ERIC Educational Resources Information Center

Nerden, J. T.; And Others

Designed for the exclusive purpose of accompanying the Project EDNEED (Empirical Determination of Nationally Essential Educational Data) classification document, this volume comprises the third of a five-volume final report. It provides uniform definitions for vocational education terms found in the EDNEED classification document, and aids in…

42 CFR 137.204 - How will this voluntary national uniform data set be developed?

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false How will this voluntary national uniform data set... Operational Provisions Health Status Reports § 137.204 How will this voluntary national uniform data set be... subset of data that is consistent with Congressional intent, minimizes reporting burdens, and responds to...

42 CFR 137.204 - How will this voluntary national uniform data set be developed?

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false How will this voluntary national uniform data set... Operational Provisions Health Status Reports § 137.204 How will this voluntary national uniform data set be... subset of data that is consistent with Congressional intent, minimizes reporting burdens, and responds to...

42 CFR 137.204 - How will this voluntary national uniform data set be developed?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false How will this voluntary national uniform data set... Operational Provisions Health Status Reports § 137.204 How will this voluntary national uniform data set be... subset of data that is consistent with Congressional intent, minimizes reporting burdens, and responds to...

42 CFR 137.204 - How will this voluntary national uniform data set be developed?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false How will this voluntary national uniform data set... Operational Provisions Health Status Reports § 137.204 How will this voluntary national uniform data set be... subset of data that is consistent with Congressional intent, minimizes reporting burdens, and responds to...

The Uniform Reporting Program

ERIC Educational Resources Information Center

Mansfield, Stephen J.

1976-01-01

The Uniform Reporting Program of the American College Health Association generalizes on the problems of health service management and then identifies specific measures and programs to relieve those problems. (MM)

Evaluation of Uniform Cost Accounting System to Fully Capture Depot Level Repair Costs.

DTIC Science & Technology

1985-12-01

RD-RI65 522 EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM TO FULLY i/I CAPTURE DEPOT LEVEL REPAIR COSTS (U) NAVAL POSTGRADUATE SCHOOL MONTEREY CA D R...8217.LECTE B ,- THESIS EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM 0TO FULLY CAPTURE DEPOT LEVEL REPAIR COSTS Jby __jDavid Richmond O’Brien lj,,, December...Include Security Classification) EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM TO FULLY CAPTURE DEPOT LEVEL REPAIR COSTS 12 PERSONAL AUTHOR(S) O’Brien- David

On numerical heat transfer characteristic study of flat surface subjected to variation in geometric thickness

NASA Astrophysics Data System (ADS)

Umair, Siddique Mohammed; Kolawale, Abhijeet Rangnath; Bhise, Ganesh Anurath; Gulhane, Nitin Parashram

Thermal management in the looming world of electronic packaging system is the most prior and conspicuous issue as far as the working efficiency of the system is concerned. The cooling in such systems can be achieved by impinging air jet over the heat sink as jet impingement cooling is one of the cooling technologies which are widely studied now. Here the modulation in impinging and geometric parameters results in the establishment of the characteristic cooling rate over the target surface. The characteristic cooling curve actually resembles non-uniformity in cooling rate. This non-uniformity favors the area average heat dissipation rate. In order to study the non-uniformity in cooling characteristic, the present study takes an initiative in plotting the local Nusselt number magnitude against the non-dimensional radial distance of the different thickness of target surfaces. For this, the steady temperature distribution over the target surface under the impingement of air jet is being determined numerically. The work is completely inclined towards the determination of critical value of geometric thickness below which the non-uniformity in the Nusselt profile starts. This is done by numerically examining different target surfaces under constant Reynolds number and nozzle-target spacing. The occurrences of non-uniformity in Nusselt profile contributes to over a 42% enhancement in area average Nusselt magnitude. The critical value of characteristic thickness (t/d) reported in the present investigation approximate to 0.05. Below this value, the impingement of air jet generates a discrete pressure zones over the target surface in the form of pressure spots. As a result of this, the air flowing in contact with the target surface experiences a damping potential, in due of which it gets more time and contact with the surface to dissipate heat.

14 CFR 04 - Air Carrier Groupings

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Air Carrier Groupings Section 04 Section... PROCEEDINGS) ECONOMIC REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 04 Air Carrier Groupings (a) All large certificated air carriers are placed into three basic air...

49 CFR 630.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION NATIONAL TRANSIT DATABASE § 630.3 Definitions. (a) Except as otherwise provided, terms defined in... current editions of the National Transit Database Reporting Manuals and the NTD Uniform System of Accounts... benefits from assistance under 49 U.S.C. 5307 or 5311. Current edition of the National Transit Database...

49 CFR 630.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION NATIONAL TRANSIT DATABASE § 630.3 Definitions. (a) Except as otherwise provided, terms defined in... current editions of the National Transit Database Reporting Manuals and the NTD Uniform System of Accounts... benefits from assistance under 49 U.S.C. 5307 or 5311. Current edition of the National Transit Database...

49 CFR 630.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION NATIONAL TRANSIT DATABASE § 630.3 Definitions. (a) Except as otherwise provided, terms defined in... current editions of the National Transit Database Reporting Manuals and the NTD Uniform System of Accounts... benefits from assistance under 49 U.S.C. 5307 or 5311. Current edition of the National Transit Database...

49 CFR 630.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION NATIONAL TRANSIT DATABASE § 630.3 Definitions. (a) Except as otherwise provided, terms defined in... current editions of the National Transit Database Reporting Manuals and the NTD Uniform System of Accounts... benefits from assistance under 49 U.S.C. 5307 or 5311. Current edition of the National Transit Database...

49 CFR 630.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION NATIONAL TRANSIT DATABASE § 630.3 Definitions. (a) Except as otherwise provided, terms defined in... current editions of the National Transit Database Reporting Manuals and the NTD Uniform System of Accounts... benefits from assistance under 49 U.S.C. 5307 or 5311. Current edition of the National Transit Database...

A chirped-pulse Fourier-transform microwave/pulsed uniform flow spectrometer. I. The low-temperature flow system.

PubMed

Oldham, James M; Abeysekera, Chamara; Joalland, Baptiste; Zack, Lindsay N; Prozument, Kirill; Sims, Ian R; Park, G Barratt; Field, Robert W; Suits, Arthur G

2014-10-21

We report the development of a new instrument that combines chirped-pulse microwave spectroscopy with a pulsed uniform supersonic flow. This combination promises a nearly universal detection method that can deliver isomer and conformer specific, quantitative detection and spectroscopic characterization of unstable reaction products and intermediates, product vibrational distributions, and molecular excited states. This first paper in a series of two presents a new pulsed-flow design, at the heart of which is a fast, high-throughput pulsed valve driven by a piezoelectric stack actuator. Uniform flows at temperatures as low as 20 K were readily achieved with only modest pumping requirements, as demonstrated by impact pressure measurements and pure rotational spectroscopy. The proposed technique will be suitable for application in diverse fields including fundamental studies in spectroscopy, kinetics, and reaction dynamics.

Management Overview of System Technical Support Plan for the FIREFINDER System Support Center.

DTIC Science & Technology

1980-08-06

34.. /b , UNCLASSIFIED SECU ITY CLASSIFICATION OF THIS PAGE (When Data Entered) READ INSTRUCTIONSREPORT DOCUMENTATION PAGE BEFORE COMPLETING FORM I. REPORT...Evaluation Agency USASA U.S. Army Security Agency UTM Universal Transverse Mercator V Volts V&V Verification and Validation VCSA Vice-Chief of Staff, Army VDD... classification , configuration audits, and so forth. INSTR 5010.27 Management of Automatic Data System 9 November 1971 Development Establishes uniform

Uniformity testing: assessment of a centralized web-based uniformity analysis system.

PubMed

Klempa, Meaghan C

2011-06-01

Uniformity testing is performed daily to ensure adequate camera performance before clinical use. The aim of this study is to assess the reliability of Beth Israel Deaconess Medical Center's locally built, centralized, Web-based uniformity analysis system by examining the differences between manufacturer and Web-based National Electrical Manufacturers Association integral uniformity calculations measured in the useful field of view (FOV) and the central FOV. Manufacturer and Web-based integral uniformity calculations measured in the useful FOV and the central FOV were recorded over a 30-d period for 4 cameras from 3 different manufacturers. These data were then statistically analyzed. The differences between the uniformity calculations were computed, in addition to the means and the SDs of these differences for each head of each camera. There was a correlation between the manufacturer and Web-based integral uniformity calculations in the useful FOV and the central FOV over the 30-d period. The average differences between the manufacturer and Web-based useful FOV calculations ranged from -0.30 to 0.099, with SD ranging from 0.092 to 0.32. For the central FOV calculations, the average differences ranged from -0.163 to 0.055, with SD ranging from 0.074 to 0.24. Most of the uniformity calculations computed by this centralized Web-based uniformity analysis system are comparable to the manufacturers' calculations, suggesting that this system is reasonably reliable and effective. This finding is important because centralized Web-based uniformity analysis systems are advantageous in that they test camera performance in the same manner regardless of the manufacturer.

46 CFR 232.1 - Purpose and applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ACTIVITIES UNIFORM FINANCIAL REPORTING REQUIREMENTS § 232.1 Purpose and applicability. (a) Purpose. The purpose of this regulation is to establish uniform reporting requirements for the preparation of financial..., as necessary, issue clarifying instructions to those subject to these reporting requirements to...

46 CFR 232.1 - Purpose and applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... ACTIVITIES UNIFORM FINANCIAL REPORTING REQUIREMENTS § 232.1 Purpose and applicability. (a) Purpose. The purpose of this regulation is to establish uniform reporting requirements for the preparation of financial..., as necessary, issue clarifying instructions to those subject to these reporting requirements to...

Upconversion Nanoparticles-Encoded Hydrogel Microbeads-Based Multiplexed Protein Detection

NASA Astrophysics Data System (ADS)

Shikha, Swati; Zheng, Xiang; Zhang, Yong

2018-06-01

Fluorescently encoded microbeads are in demand for multiplexed applications in different fields. Compared to organic dye-based commercially available Luminex's xMAP technology, upconversion nanoparticles (UCNPs) are better alternatives due to their large anti-Stokes shift, photostability, nil background, and single wavelength excitation. Here, we developed a new multiplexed detection system using UCNPs for encoding poly(ethylene glycol) diacrylate (PEGDA) microbeads as well as for labeling reporter antibody. However, to prepare UCNPs-encoded microbeads, currently used swelling-based encapsulation leads to non-uniformity, which is undesirable for fluorescence-based multiplexing. Hence, we utilized droplet microfluidics to obtain encoded microbeads of uniform size, shape, and UCNPs distribution inside. Additionally, PEGDA microbeads lack functionality for probe antibodies conjugation on their surface. Methods to functionalize the surface of PEGDA microbeads (acrylic acid incorporation, polydopamine coating) reported thus far quench the fluorescence of UCNPs. Here, PEGDA microbeads surface was coated with silica followed by carboxyl modification without compromising the fluorescence intensity of UCNPs. In this study, droplet microfluidics-assisted UCNPs-encoded microbeads of uniform shape, size, and fluorescence were prepared. Multiple color codes were generated by mixing UCNPs emitting red and green colors at different ratios prior to encapsulation. UCNPs emitting blue color were used to label the reporter antibody. Probe antibodies were covalently immobilized on red UCNPs-encoded microbeads for specific capture of human serum albumin (HSA) as a model protein. The system was also demonstrated for multiplexed detection of both human C-reactive protein (hCRP) and HSA protein by immobilizing anti-hCRP antibodies on green UCNPs.

Optical design for uniform scanning in MEMS-based 3D imaging lidar.

PubMed

Lee, Xiaobao; Wang, Chunhui

2015-03-20

This paper proposes a method for the optical system design of uniform scanning in a larger scan field of view (FOV) in 3D imaging lidar. The theoretical formulas are derived for the design scheme. By employing the optical design software ZEMAX, a foldaway uniform scanning optical system based on MEMS has been designed, and the scanning uniformity and spot size of the system on the target plane, perpendicular to optical axis, are analyzed and discussed. Results show that the designed system can scan uniformly within the FOV of 40°×40° with small spot size for the target at distance of about 100 m.

Sound and Unsound Options for Reform

ERIC Educational Resources Information Center

Finn, Chester E., Jr.

2004-01-01

Test results and employer complaints indicate that the average high school graduate hasn't learned enough and that he brings that deficit with him to college. As remedy, Chester Finn argues for uniform educational standards and measurements in a transparent reporting system that gives families the information necessary to scrutinize and accept or…

Train the Trainer. Final Report. Fiscal Year 1997-1998.

ERIC Educational Resources Information Center

TIU Adult Education and Job Training Center, Lewistown, PA.

A project designed an operational system and develop a skilled pool of trainers, in conjunction with Pennsylvania's Regional Professional Development Centers (PDCs), to deliver high-quality, uniform training modules in needed content areas to adult basic and literacy education (ABLE) staff throughout Pennsylvania. Procedures for identifying,…

Financial Reporting for Public Institutions in New Mexico.

ERIC Educational Resources Information Center

New Mexico Commission on Higher Education.

This manual is intended to provide public institutions of higher education in New Mexico with a consistent and uniform system for treating institutional finance data. Part 1 presents accounting principles for fund accounting, restricted and unrestricted funds, accrual accounting, and handling other charges and revenues. Part 2 provides general…

14 CFR Section 04 - Air Carrier Groupings

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Air Carrier Groupings Section 04 Section 04... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 04 Air Carrier Groupings (a) All large certificated air carriers are placed into three basic air carrier groupings based...

14 CFR Section 04 - Air Carrier Groupings

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Air Carrier Groupings Section 04 Section 04... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 04 Air Carrier Groupings (a) All large certificated air carriers are placed into three basic air carrier groupings based...

14 CFR Section 04 - Air Carrier Groupings

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Air Carrier Groupings Section 04 Section 04... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 04 Air Carrier Groupings (a) All large certificated air carriers are placed into three basic air carrier groupings based...

14 CFR Section 04 - Air Carrier Groupings

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Air Carrier Groupings Section 04 Section 04... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Section 04 Air Carrier Groupings (a) All large certificated air carriers are placed into three basic air carrier groupings based...

Parent Child Center Program Management Information System. User's Manual.

ERIC Educational Resources Information Center

Warner, Donna D.; And Others

This manual describes procedures for collecting, recording, and reporting in a uniform, timely manner critical information necessary to the making of key management decisions for parent child centers as well as for the parent child center program. The first section describes recommended data collection and recordkeeping procedures for such…

14 CFR Section 4 - General

Code of Federal Regulations, 2010 CFR

2010-01-01

... UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS Balance Sheet Classifications Section 4 General (a) The balance sheet accounts are designed to show the financial condition of the air... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false General Section 4 Section 4 Aeronautics and...

14 CFR Sec. 1-6 - Accounting entities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Accounting entities. Sec. 1-6 Section 1-6... REGULATIONS UNIFORM SYSTEM OF ACCOUNTS AND REPORTS FOR LARGE CERTIFICATED AIR CARRIERS General Accounting Provisions Sec. 1-6 Accounting entities. (a) Separate accounting records shall be maintained for each air...

Documentation and Analysis of the ’Miscellaneous’ Account Category within the DoD Instruction 7220.29-H Depot Level Maintenance Cost Accounting System.

DTIC Science & Technology

1984-12-01

34MISCELLANEOUS" ACCOUNT CATEGORY WITHIN THE DOD INSTRUCTION 7220.29-H DEPOT LEVEL MAINTENANCE COST ACCOUNTING SYSTEM by a. Steven Eugene Lehr CDecember 1984...PERFORMING ONG. REPORT NUMBER Maintenance Cost Accounting System 7. AUTHOR(&) S. CONTRACT OR GRANT NUMBER(@) Steven Eugene Lehr 9. PERFORMING ORGANIZATION...Availability Codes IS. KEY WORDS (Continue on reverse *ids It necessary and Identify by block number) Dvi Special Uniform Cost Accounting System DoD

The distribution of cigarette prices under different tax structures: findings from the International Tobacco Control Policy Evaluation (ITC) Project

PubMed Central

Shang, Ce; Chaloupka, Frank J; Zahra, Nahleen; Fong, Geoffrey T

2013-01-01

Background The distribution of cigarette prices has rarely been studied and compared under different tax structures. Descriptive evidence on price distributions by countries can shed light on opportunities for tax avoidance and brand switching under different tobacco tax structures, which could impact the effectiveness of increased taxation in reducing smoking. Objective This paper aims to describe the distribution of cigarette prices by countries and to compare these distributions based on the tobacco tax structure in these countries. Methods We employed data for 16 countries taken from the International Tobacco Control Policy Evaluation Project to construct survey-derived cigarette prices for each country. Self-reported prices were weighted by cigarette consumption and described using a comprehensive set of statistics. We then compared these statistics for cigarette prices under different tax structures. In particular, countries of similar income levels and countries that impose similar total excise taxes using different tax structures were paired and compared in mean and variance using a two-sample comparison test. Findings Our investigation illustrates that, compared with specific uniform taxation, other tax structures, such as ad valorem uniform taxation, mixed (a tax system using ad valorem and specific taxes) uniform taxation, and tiered tax structures of specific, ad valorem and mixed taxation tend to have price distributions with greater variability. Countries that rely heavily on ad valorem and tiered taxes also tend to have greater price variability around the median. Among mixed taxation systems, countries that rely more heavily on the ad valorem component tend to have greater price variability than countries that rely more heavily on the specific component. In countries with tiered tax systems, cigarette prices are skewed more towards lower prices than are prices under uniform tax systems. The analyses presented here demonstrate that more opportunities exist for tax avoidance and brand switching when the tax structure departs from a uniform specific tax. PMID:23792324

The distribution of cigarette prices under different tax structures: findings from the International Tobacco Control Policy Evaluation (ITC) Project.

PubMed

Shang, Ce; Chaloupka, Frank J; Zahra, Nahleen; Fong, Geoffrey T

2014-03-01

The distribution of cigarette prices has rarely been studied and compared under different tax structures. Descriptive evidence on price distributions by countries can shed light on opportunities for tax avoidance and brand switching under different tobacco tax structures, which could impact the effectiveness of increased taxation in reducing smoking. This paper aims to describe the distribution of cigarette prices by countries and to compare these distributions based on the tobacco tax structure in these countries. We employed data for 16 countries taken from the International Tobacco Control Policy Evaluation Project to construct survey-derived cigarette prices for each country. Self-reported prices were weighted by cigarette consumption and described using a comprehensive set of statistics. We then compared these statistics for cigarette prices under different tax structures. In particular, countries of similar income levels and countries that impose similar total excise taxes using different tax structures were paired and compared in mean and variance using a two-sample comparison test. Our investigation illustrates that, compared with specific uniform taxation, other tax structures, such as ad valorem uniform taxation, mixed (a tax system using ad valorem and specific taxes) uniform taxation, and tiered tax structures of specific, ad valorem and mixed taxation tend to have price distributions with greater variability. Countries that rely heavily on ad valorem and tiered taxes also tend to have greater price variability around the median. Among mixed taxation systems, countries that rely more heavily on the ad valorem component tend to have greater price variability than countries that rely more heavily on the specific component. In countries with tiered tax systems, cigarette prices are skewed more towards lower prices than are prices under uniform tax systems. The analyses presented here demonstrate that more opportunities exist for tax avoidance and brand switching when the tax structure departs from a uniform specific tax.

NASA aviation safety reporting system

NASA Technical Reports Server (NTRS)

1978-01-01

Reports describing various types of communication problems are presented along with summaries dealing with judgment and decision making. Concerns relating to the ground proximity warning system are summarized and several examples of true terrain proximity warnings are provided. An analytic study of reports relating to profile descents was performed. Problems were found to be associated with charting and graphic presentation of the descents, with lack of uniformity of the descent procedures among facilities using them, and with the flight crew workload engendered by profile descents, particularly when additional requirements are interposed by air traffic control during the execution of the profiles. A selection of alert bulletins and responses to them were reviewed.

Effective electrodiffusion equation for non-uniform nanochannels.

PubMed

Marini Bettolo Marconi, Umberto; Melchionna, Simone; Pagonabarraga, Ignacio

2013-06-28

We derive a one-dimensional formulation of the Planck-Nernst-Poisson equation to describe the dynamics of a symmetric binary electrolyte in channels whose section is nanometric and varies along the axial direction. The approach is in the spirit of the Fick-Jacobs diffusion equation and leads to a system of coupled equations for the partial densities which depends on the charge sitting at the walls in a non-trivial fashion. We consider two kinds of non-uniformities, those due to the spatial variation of charge distribution and those due to the shape variation of the pore and report one- and three-dimensional solutions of the electrokinetic equations.

Who are the owners of firearms used in adolescent suicides?

PubMed

Johnson, Renee M; Barber, Catherine; Azrael, Deborah; Clark, David E; Hemenway, David

2010-12-01

In this brief report, the source of firearms used in adolescent suicides was examined using data from the National Violent Injury Statistics System, the pilot to the CDC's National Violent Death Reporting System, a uniform reporting system for violent and firearm-related deaths. Data represent the 63 firearm suicides among youth (<18 yrs) that occurred in 2001 or 2002 in one of four states (CT, ME, UT, WI) or two metropolitan counties (San Francisco, CA; Allegheny County, PA). Four-fifths of the suicides took place in the decedents' homes, and--when the firearm owner was known--most of the firearms were owned by parents. Findings replicate results from previous research and highlight the importance of limiting youth access to firearms.

A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber

NASA Astrophysics Data System (ADS)

Chiang, W. Y.; Wu, M. H.; Wu, K. L.; Lin, M. H.; Teng, H. H.; Tsai, Y. F.; Ko, C. C.; Yang, E. C.; Jiang, J. A.; Barnett, L. R.; Chu, K. R.

2014-08-01

Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber.

PubMed

Chiang, W Y; Wu, M H; Wu, K L; Lin, M H; Teng, H H; Tsai, Y F; Ko, C C; Yang, E C; Jiang, J A; Barnett, L R; Chu, K R

2014-08-01

Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

The 13-inch magnetic suspension and balance system wind tunnel

NASA Technical Reports Server (NTRS)

Johnson, William G., Jr.; Dress, David A.

1989-01-01

NASA Langley has a small, subsonic wind tunnel in use with the 13-inch Magnetic Suspension and Balance System (MSBS). The tunnel is capable of speeds up to Mach 0.5. This report presents tunnel design and construction details. It includes flow uniformity, angularity, and velocity fluctuation data. It also compares experimental Mach number distribution data with computed results for the General Electric Streamtube Curvature Program.

The Uniformed and Overseas Citizens Absentee Voting Act: Overview and Issues

DTIC Science & Technology

2010-12-06

CRS Report for Congress Prepared for Members and Committees of Congress The Uniformed and Overseas Citizens Absentee Voting Act...REPORT TYPE 3. DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE The Uniformed and Overseas Citizens Absentee Voting Act: Overview and... PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Congressional Research Service,The Library of Congress,101 Independence Avenue SE,Washington,DC,20540

76 FR 13699 - Reports, Forms and Recordkeeping Requirements Information Collection Activity Under OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

...: Uniform Financial Reporting Requirements. OMB Control Number: 2133-0005. Type of Request: Extension of...(s): MA-172. Abstract: The Uniform Financial Reporting Requirements are used as a basis for preparing and filing semi-annual and annual financial statements with the Maritime Administration. Regulations...

VHA mental health information system: applying health information technology to monitor and facilitate implementation of VHA Uniform Mental Health Services Handbook requirements.

PubMed

Trafton, Jodie A; Greenberg, Greg; Harris, Alex H S; Tavakoli, Sara; Kearney, Lisa; McCarthy, John; Blow, Fredric; Hoff, Rani; Schohn, Mary

2013-03-01

To describe the design and deployment of health information technology to support implementation of mental health services policy requirements in the Veterans Health Administration (VHA). Using administrative and self-report survey data, we developed and fielded metrics regarding implementation of the requirements delineated in the VHA Uniform Mental Health Services Handbook. Finalized metrics were incorporated into 2 external facilitation-based quality improvement programs led by the VHA Mental Health Operations. To support these programs, tailored site-specific reports were generated. Metric development required close collaboration between program evaluators, policy makers and clinical leadership, and consideration of policy language and intent. Electronic reports supporting different purposes required distinct formatting and presentation features, despite their having similar general goals and using the same metrics. Health information technology can facilitate mental health policy implementation but must be integrated into a process of consensus building and close collaboration with policy makers, evaluators, and practitioners.

A Comparison of the Scorpion Load Carriage System (SLCS) to the Modular Lightweight Load Carrying Equipment (MOLLE)

DTIC Science & Technology

2003-07-01

volunteer was asked to report wearing Battle Dress Uniform or Under Armor Undergarment) because the reflective markers used for motion capture needed to be...data collection sessions wearing Under Armor Undergarment, combat boots, integrated body armor and Scorpion helmet. Subjects were given time to

Appropriate time scales for nonlinear analyses of deterministic jump systems

NASA Astrophysics Data System (ADS)

Suzuki, Tomoya

2011-06-01

In the real world, there are many phenomena that are derived from deterministic systems but which fluctuate with nonuniform time intervals. This paper discusses the appropriate time scales that can be applied to such systems to analyze their properties. The financial markets are an example of such systems wherein price movements fluctuate with nonuniform time intervals. However, it is common to apply uniform time scales such as 1-min data and 1-h data to study price movements. This paper examines the validity of such time scales by using surrogate data tests to ascertain whether the deterministic properties of the original system can be identified from uniform sampled data. The results show that uniform time samplings are often inappropriate for nonlinear analyses. However, for other systems such as neural spikes and Internet traffic packets, which produce similar outputs, uniform time samplings are quite effective in extracting the system properties. Nevertheless, uniform samplings often generate overlapping data, which can cause false rejections of surrogate data tests.

Utility of the Paris System in Reporting Urine Cytology.

PubMed

Malviya, Kiran; Fernandes, Gwendolyn; Naik, Leena; Kothari, Kanchan; Agnihotri, Mona

2017-01-01

To find out the utility of The Paris System (TPS) in reporting urine cytology and to compare it with the reporting system currently used in our laboratory. This retrospective study was undertaken over a period of 1 year during which slides of all the urine specimens sent for cytological examination were retrieved from our laboratory filling system. They were blindly reviewed and reclassified according to TPS. Surgical follow-up was obtained from the uropathology services of our department. A total of 176 cases were meticulously reviewed. The mean age of the patients was 52 years, and 71% of cases presented with hematuria. Histopathological follow-up was available in 34 cases. Reporting by TPS detected 13.0% high-grade urothelial carcinoma (HGUC) and 5.1% atypical urothelial cells versus 7.3 and 11.9% by the current reporting system, respectively. The sensitivity and diagnostic accuracy for detecting HGUC of TPS were higher than those of our reporting system. TPS has increased the rate of detection of HGUC and reduced the rate of reporting "atypical" urothelial cells. TPS has also standardized the diagnostic criteria, thereby bringing uniformity and reproducibility into the system of reporting for urine cytology. © 2017 S. Karger AG, Basel.

Impact of Uniform Methods on Interlaboratory Antibody Titration Variability: Antibody Titration and Uniform Methods.

PubMed

Bachegowda, Lohith S; Cheng, Yan H; Long, Thomas; Shaz, Beth H

2017-01-01

-Substantial variability between different antibody titration methods prompted development and introduction of uniform methods in 2008. -To determine whether uniform methods consistently decrease interlaboratory variation in proficiency testing. -Proficiency testing data for antibody titration between 2009 and 2013 were obtained from the College of American Pathologists. Each laboratory was supplied plasma and red cells to determine anti-A and anti-D antibody titers by their standard method: gel or tube by uniform or other methods at different testing phases (immediate spin and/or room temperature [anti-A], and/or anti-human globulin [AHG: anti-A and anti-D]) with different additives. Interlaboratory variations were compared by analyzing the distribution of titer results by method and phase. -A median of 574 and 1100 responses were reported for anti-A and anti-D antibody titers, respectively, during a 5-year period. The 3 most frequent (median) methods performed for anti-A antibody were uniform tube room temperature (147.5; range, 119-159), uniform tube AHG (143.5; range, 134-150), and other tube AHG (97; range, 82-116); for anti-D antibody, the methods were other tube (451; range, 431-465), uniform tube (404; range, 382-462), and uniform gel (137; range, 121-153). Of the larger reported methods, uniform gel AHG phase for anti-A and anti-D antibodies had the most participants with the same result (mode). For anti-A antibody, 0 of 8 (uniform versus other tube room temperature) and 1 of 8 (uniform versus other tube AHG), and for anti-D antibody, 0 of 8 (uniform versus other tube) and 0 of 8 (uniform versus other gel) proficiency tests showed significant titer variability reduction. -Uniform methods harmonize laboratory techniques but rarely reduce interlaboratory titer variance in comparison with other methods.

Modulus spectroscopy of grain-grain boundary binary system

NASA Astrophysics Data System (ADS)

Cheng, Peng-Fei; Song, Jiang; Li, Sheng-Tao; Wang, Hui

2015-02-01

Understanding various polarization mechanisms in complex dielectric systems and specifying their physical origins are key issues in dielectric physics. In this paper, four different methods for representing dielectric properties were analyzed and compared. Depending on the details of the system under study, i.e., uniform or non-uniform, it was suggested that different representing approaches should be used to obtain more valuable information. Especially, for the grain-grain boundary binary non-uniform system, its dielectric response was analyzed in detail in terms of modulus spectroscopy (MS). Furthermore, it was found that through MS, the dielectric responses between uniform and non-uniform systems, grain and grain boundary, Maxwell-Wagner polarization and intrinsic polarization can be distinguished. Finally, with the proposed model, the dielectric properties of CaCu3Ti4O12 (CCTO) ceramics were studied. The colossal dielectric constant of CCTO at low frequency was attributed to the pseudo relaxation process of grain.

Foundations for a syntatic pattern recognition system for genomic DNA sequences. [Annual] report, 1 December 1991--31 March 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Searles, D.B.

1993-03-01

The goal of the proposed work is the creation of a software system that will perform sophisticated pattern recognition and related functions at a level of abstraction and with expressive power beyond current general-purpose pattern-matching systems for biological sequences; and with a more uniform language, environment, and graphical user interface, and with greater flexibility, extensibility, embeddability, and ability to incorporate other algorithms, than current special-purpose analytic software.

Time needed to achieve completeness and accuracy in bedside lung ultrasound reporting in intensive care unit.

PubMed

Tutino, Lorenzo; Cianchi, Giovanni; Barbani, Francesco; Batacchi, Stefano; Cammelli, Rita; Peris, Adriano

2010-08-12

The use of lung ultrasound (LUS) in ICU is increasing but ultrasonographic patterns of lung are often difficult to quantify by different operators. The aim of this study was to evaluate the accuracy and quality of LUS reporting after the introduction of a standardized electronic recording sheet. Intensivists were trained for LUS following a teaching programme. From April 2008, an electronic sheet was designed and introduced in ICU database in order to uniform LUS examination reporting. A mark from 0 to 24 has been given for each exam by two senior intensivists not involved in the survey. The mark assigned was based on completeness of a precise reporting scheme, concerning the main finding of LUS. A cut off of 15 was considered sufficiency. The study comprehended 12 months of observations and a total of 637 LUS. Initially, although some improvement in the reports completeness, still the accuracy and precision of examination reporting was below 15. The time required to reach a sufficient quality was 7 months. A linear trend in physicians progress was observed. The uniformity in teaching programme and examinations reporting system permits to improve the level of completeness and accuracy of LUS reporting, helping physicians in following lung pathology evolution.

Microwave Tube Reliability

DTIC Science & Technology

1976-06-01

t’ibes discussed demonstrate a 2000-hour life in the laboratory but exhibit only a 200- hour i’fc in systems. The tubes reported on were broadband , helix ...control. Two such critical operations are helix winding and pyrolytic deposition. The ,slow-wave structureof .he modem TWT -is rarely a simple uniform...Il No customer complaint (2) 1I Open helix (1) 1 High harmonics, low power<l) The group A and B -symptoms indicated by the failure report data weL

Bridging the integration gap between imaging and information systems: a uniform data concept for content-based image retrieval in computer-aided diagnosis.

PubMed

Welter, Petra; Riesmeier, Jörg; Fischer, Benedikt; Grouls, Christoph; Kuhl, Christiane; Deserno, Thomas M

2011-01-01

It is widely accepted that content-based image retrieval (CBIR) can be extremely useful for computer-aided diagnosis (CAD). However, CBIR has not been established in clinical practice yet. As a widely unattended gap of integration, a unified data concept for CBIR-based CAD results and reporting is lacking. Picture archiving and communication systems and the workflow of radiologists must be considered for successful data integration to be achieved. We suggest that CBIR systems applied to CAD should integrate their results in a picture archiving and communication systems environment such as Digital Imaging and Communications in Medicine (DICOM) structured reporting documents. A sample DICOM structured reporting template adaptable to CBIR and an appropriate integration scheme is presented. The proposed CBIR data concept may foster the promulgation of CBIR systems in clinical environments and, thereby, improve the diagnostic process.

Bridging the integration gap between imaging and information systems: a uniform data concept for content-based image retrieval in computer-aided diagnosis

PubMed Central

Riesmeier, Jörg; Fischer, Benedikt; Grouls, Christoph; Kuhl, Christiane; Deserno (né Lehmann), Thomas M

2011-01-01

It is widely accepted that content-based image retrieval (CBIR) can be extremely useful for computer-aided diagnosis (CAD). However, CBIR has not been established in clinical practice yet. As a widely unattended gap of integration, a unified data concept for CBIR-based CAD results and reporting is lacking. Picture archiving and communication systems and the workflow of radiologists must be considered for successful data integration to be achieved. We suggest that CBIR systems applied to CAD should integrate their results in a picture archiving and communication systems environment such as Digital Imaging and Communications in Medicine (DICOM) structured reporting documents. A sample DICOM structured reporting template adaptable to CBIR and an appropriate integration scheme is presented. The proposed CBIR data concept may foster the promulgation of CBIR systems in clinical environments and, thereby, improve the diagnostic process. PMID:21672913

On exact solutions for disturbances to the asymptotic suction boundary layer: transformation of Barnes integrals to convolution integrals

NASA Astrophysics Data System (ADS)

Russell, John

2000-11-01

A modified Orr-Sommerfeld equation that applies to the asymptotic suction boundary layer was reported by Bussmann & Münz in a wartime report dated 1942 and by Hughes & Reid in J.F.M. ( 23, 1965, p715). Fundamental systems of exact solutions of the Orr-Sommerfeld equation for this mean velocity distribution were reported by D. Grohne in an unpublished typescript dated 1950. Exact solutions of the equation of Bussmann, Münz, Hughes, & Reid were reported by P. Baldwin in Mathematika ( 17, 1970, p206). Grohne and Baldwin noticed that these exact solutions may be expressed either as Barnes integrals or as convolution integrals. In a later paper (Phil. Trans. Roy. Soc. A, 399, 1985, p321), Baldwin applied the convolution integrals in the contruction of large-Reynolds number asymptotic approximations that hold uniformly. The present talk discusses the subtleties that arise in the construction of such convolution integrals, including several not reported by Grohne or Baldwin. The aim is to recover the full set of seven solutions (one well balanced, three balanced, and three dominant-recessive) postulated by W.H. Reid in various works on the uniformly valid solutions.

Light sheet theta microscopy for rapid high-resolution imaging of large biological samples.

PubMed

Migliori, Bianca; Datta, Malika S; Dupre, Christophe; Apak, Mehmet C; Asano, Shoh; Gao, Ruixuan; Boyden, Edward S; Hermanson, Ola; Yuste, Rafael; Tomer, Raju

2018-05-29

Advances in tissue clearing and molecular labeling methods are enabling unprecedented optical access to large intact biological systems. These developments fuel the need for high-speed microscopy approaches to image large samples quantitatively and at high resolution. While light sheet microscopy (LSM), with its high planar imaging speed and low photo-bleaching, can be effective, scaling up to larger imaging volumes has been hindered by the use of orthogonal light sheet illumination. To address this fundamental limitation, we have developed light sheet theta microscopy (LSTM), which uniformly illuminates samples from the same side as the detection objective, thereby eliminating limits on lateral dimensions without sacrificing the imaging resolution, depth, and speed. We present a detailed characterization of LSTM, and demonstrate its complementary advantages over LSM for rapid high-resolution quantitative imaging of large intact samples with high uniform quality. The reported LSTM approach is a significant step for the rapid high-resolution quantitative mapping of the structure and function of very large biological systems, such as a clarified thick coronal slab of human brain and uniformly expanded tissues, and also for rapid volumetric calcium imaging of highly motile animals, such as Hydra, undergoing non-isomorphic body shape changes.

49 CFR 26.47 - Can recipients be penalized for failing to meet overall goals?

Code of Federal Regulations, 2013 CFR

2013-10-01

... awards and commitments shown on your Uniform Report of Awards or Commitments and Payments at the end of... operating administration approves the report, you will be regarded as complying with the requirements of... recipient, your Uniform Report of DBE Awards or Commitments and Payments or other information coming to the...

49 CFR 26.47 - Can recipients be penalized for failing to meet overall goals?

Code of Federal Regulations, 2014 CFR

2014-10-01

... awards and commitments shown on your Uniform Report of Awards or Commitments and Payments at the end of... operating administration approves the report, you will be regarded as complying with the requirements of... recipient, your Uniform Report of DBE Awards or Commitments and Payments or other information coming to the...

49 CFR 26.47 - Can recipients be penalized for failing to meet overall goals?

Code of Federal Regulations, 2012 CFR

2012-10-01

... awards and commitments shown on your Uniform Report of Awards or Commitments and Payments at the end of... operating administration approves the report, you will be regarded as complying with the requirements of... recipient, your Uniform Report of DBE Awards or Commitments and Payments or other information coming to the...

JPRS Report, China

DTIC Science & Technology

1991-01-25

management system for student attendance, related to "double basics" education. They also develop teacher and student appraisals, examinations and essay... managed uniformly and losses are reflected agent enterprises have established a relationship in which centrally, profit and loss are clearly...strengthening organizations, many other have except for those in a few counties and townships, before given professional training to teachers and managers

Design of light guide sleeve on hyperspectral imaging system for skin diagnosis

NASA Astrophysics Data System (ADS)

Yan, Yung-Jhe; Chang, Chao-Hsin; Huang, Ting-Wei; Chiang, Hou-Chi; Wu, Jeng-Fu; Ou-Yang, Mang

2017-08-01

A hyperspectral imaging system is proposed for early study of skin diagnosis. A stable and high hyperspectral image quality is important for analysis. Therefore, a light guide sleeve (LGS) was designed for the embedded on a hyperspectral imaging system. It provides a uniform light source on the object plane with the determined distance. Furthermore, it can shield the ambient light from entering the system and increasing noise. For the purpose of producing a uniform light source, the LGS device was designed in the symmetrical double-layered structure. It has light cut structures to adjust distribution of rays between two layers and has the Lambertian surface in the front-end to promote output uniformity. In the simulation of the design, the uniformity of illuminance was about 91.7%. In the measurement of the actual light guide sleeve, the uniformity of illuminance was about 92.5%.

Analytical solutions for one-, two-, and three-dimensional solute transport in ground-water systems with uniform flow

USGS Publications Warehouse

Wexler, Eliezer J.

1989-01-01

Analytical solutions to the advective-dispersive solute-transport equation are useful in predicting the fate of solutes in ground water. Analytical solutions compiled from available literature or derived by the author are presented in this report for a variety of boundary condition types and solute-source configurations in one-, two-, and three-dimensional systems with uniform ground-water flow. A set of user-oriented computer programs was created to evaluate these solutions and to display the results in tabular and computer-graphics format. These programs incorporate many features that enhance their accuracy, ease of use, and versatility. Documentation for the programs describes their operation and required input data, and presents the results of sample problems. Derivations of select solutions, source codes for the computer programs, and samples of program input and output also are included.

RTS2: a powerful robotic observatory manager

NASA Astrophysics Data System (ADS)

Kubánek, Petr; Jelínek, Martin; Vítek, Stanislav; de Ugarte Postigo, Antonio; Nekola, Martin; French, John

2006-06-01

RTS2, or Remote Telescope System, 2nd Version, is an integrated package for remote telescope control under the Linux operating system. It is designed to run in fully autonomous mode, picking targets from a database table, storing image meta data to the database, processing images and storing their WCS coordinates in the database and offering Virtual-Observatory enabled access to them. It is currently running on various telescope setups world-wide. For control of devices from various manufacturers we developed an abstract device layer, enabling control of all possible combinations of mounts, CCDs, photometers, roof and cupola controllers. We describe the evolution of RTS2 from Python-based RTS to C and later C++ based RTS2, focusing on the problems we faced during development. The internal structure of RTS2, focusing on object layering, which is used to uniformly control various devices and provides uniform reporting layer, is also discussed.

25 CFR 900.68 - Will this uniform data set be required of all Indian tribe or tribal organizations contracting...

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false Will this uniform data set be required of all Indian... Reports and Data Requirements § 900.68 Will this uniform data set be required of all Indian tribe or tribal organizations contracting with the IHS under the Act? No. The uniform data set, applicable to the...

25 CFR 900.68 - Will this uniform data set be required of all Indian tribe or tribal organizations contracting...

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 2 2011-04-01 2011-04-01 false Will this uniform data set be required of all Indian... Reports and Data Requirements § 900.68 Will this uniform data set be required of all Indian tribe or tribal organizations contracting with the IHS under the Act? No. The uniform data set, applicable to the...

25 CFR 900.68 - Will this uniform data set be required of all Indian tribe or tribal organizations contracting...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Will this uniform data set be required of all Indian... Reports and Data Requirements § 900.68 Will this uniform data set be required of all Indian tribe or tribal organizations contracting with the IHS under the Act? No. The uniform data set, applicable to the...

25 CFR 900.68 - Will this uniform data set be required of all Indian tribe or tribal organizations contracting...

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false Will this uniform data set be required of all Indian... Reports and Data Requirements § 900.68 Will this uniform data set be required of all Indian tribe or tribal organizations contracting with the IHS under the Act? No. The uniform data set, applicable to the...

25 CFR 900.68 - Will this uniform data set be required of all Indian tribe or tribal organizations contracting...

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 2 2012-04-01 2012-04-01 false Will this uniform data set be required of all Indian... Reports and Data Requirements § 900.68 Will this uniform data set be required of all Indian tribe or tribal organizations contracting with the IHS under the Act? No. The uniform data set, applicable to the...

Determination of the microbolometric FPA's responsivity with imaging system's radiometric considerations

NASA Astrophysics Data System (ADS)

Gogler, Slawomir; Bieszczad, Grzegorz; Krupinski, Michal

2013-10-01

Thermal imagers and used therein infrared array sensors are subject to calibration procedure and evaluation of their voltage sensitivity on incident radiation during manufacturing process. The calibration procedure is especially important in so-called radiometric cameras, where accurate radiometric quantities, given in physical units, are of concern. Even though non-radiometric cameras are not expected to stand up to such elevated standards, it is still important, that the image faithfully represents temperature variations across the scene. Detectors used in thermal camera are illuminated by infrared radiation transmitted through an infrared transmitting optical system. Often an optical system, when exposed to uniform Lambertian source forms a non-uniform irradiation distribution in its image plane. In order to be able to carry out an accurate non-uniformity correction it is essential to correctly predict irradiation distribution from a uniform source. In the article a non-uniformity correction method has been presented, that takes into account optical system's radiometry. Predictions of the irradiation distribution have been confronted with measured irradiance values. Presented radiometric model allows fast and accurate non-uniformity correction to be carried out.

Improved sensitivity via layered-double-hydroxide-uniformity-dependent chemiluminescence.

PubMed

Li, Zenghe; Wang, Dan; Yuan, Zhiqin; Lu, Chao

2016-12-01

In the last two decades nanoparticles have been widely applied to enhance chemiluminescence (CL). The morphology of nanoparticles has an important influence on nanoparticle-amplified CL. However, studies of nanoparticle-amplified CL focus mainly on the size and shape effects, and no attempt has been made to explore the influence of uniformity in nanoparticle-amplified CL processes. In this study we have investigated nanoparticle uniformity in the luminol-H 2 O 2 CL system using layered double hydroxides (LDHs) as a model material. The results demonstrated that the uniformity of LDHs played a key role in CL amplification. A possible mechanism is that LDHs with high uniformity possess abundant catalytic active sites, which results in high CL intensity. Meanwhile, the sensitivity for H 2 O 2 detection was increased by one order of magnitude (1.0 nM). Moreover, the uniform-LDH-amplified luminol CL could be applied to selective detection of glucose in human plasma samples. Furthermore, such a uniformity-dependent CL enhancement effect could adapted to other redox CL systems-for example, the peroxynitrous acid (ONOOH) CL system.

Optical design and fabrication of palm/fingerprint uniform illumination system with a high-power near-infrared light-emitting diode.

PubMed

Jing, Lei; Wang, Yao; Zhao, Huifu; Ke, Hongliang; Wang, Xiaoxun; Gao, Qun

2017-06-10

In order to meet the requirements of uniform illumination for optical palm/fingerprint instruments and overcome the shortcomings of the poor uniform illumination on the working plane of the optical palm/fingerprint prism, a novel secondary optical lens with a free-form surface, compact structure, and high uniformity is presented in this paper. The design of the secondary optical lens is based on emission properties of the near-infrared light-emitting diode (LED) and basic principles of non-imaging optics, especially considering the impact of the thickness of the prism in the design. Through the numerical solution of Snell's law in geometric optics, we obtain the profile of the free-form surface of the lens. Using the optical software TracePro, we trace and simulate the illumination system. The results show that the uniformity is 89.8% on the working plane of the prism, and the test results show that the actual uniformity reaches 85.7% in the experiment, which provides an effective way for realizing a highly uniform illumination system with high-power near-infrared LED.

Evaluation of illumination system uniformity for wide-field biomedical hyperspectral imaging

NASA Astrophysics Data System (ADS)

Sawyer, Travis W.; Siri Luthman, A.; E Bohndiek, Sarah

2017-04-01

Hyperspectral imaging (HSI) systems collect both spatial (morphological) and spectral (chemical) information from a sample. HSI can provide sensitive analysis for biological and medical applications, for example, simultaneously measuring reflectance and fluorescence properties of a tissue, which together with structural information could improve early cancer detection and tumour characterisation. Illumination uniformity is a critical pre-condition for quantitative data extraction from an HSI system. Non-uniformity can cause glare, specular reflection and unwanted shading, which negatively impact statistical analysis procedures used to extract abundance of different chemical species. Here, we model and evaluate several illumination systems frequently used in wide-field biomedical imaging to test their potential for HSI. We use the software LightTools and FRED. The analysed systems include: a fibre ring light; a light emitting diode (LED) ring; and a diffuse scattering dome. Each system is characterised for spectral, spatial, and angular uniformity, as well as transfer efficiency. Furthermore, an approach to measure uniformity using the Kullback-Leibler divergence (KLD) is introduced. The KLD is generalisable to arbitrary illumination shapes, making it an attractive approach for characterising illumination distributions. Although the systems are quite comparable in their spatial and spectral uniformity, the most uniform angular distribution is achieved using a diffuse scattering dome, yielding a contrast of 0.503 and average deviation of 0.303 over a ±60° field of view with a 3.9% model error in the angular domain. Our results suggest that conventional illumination sources can be applied in HSI, but in the case of low light levels, bespoke illumination sources may offer improved performance.

75 FR 76077 - Information Collection Available for Public Comments and Recommendations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... from that office. SUPPLEMENTARY INFORMATION: Title of Collection: Uniform Financial Reporting... Office of Management and Budget. Summary of Collection of Information: The Uniform Financial Reporting Requirements are used as a basis for preparing and filing semi-annual and annual financial statements with the...

Earthquake-Related Injuries in the Pediatric Population: A Systematic Review

PubMed Central

Jacquet, Gabrielle A.; Hansoti, Bhakti; Vu, Alexander; Bayram, Jamil D.

2013-01-01

Background: Children are a special population, particularly susceptible to injury. Registries for various injury types in the pediatric population are important, not only for epidemiological purposes but also for their implications on intervention programs. Although injury registries already exist, there is no uniform injury classification system for traumatic mass casualty events such as earthquakes. Objective: To systematically review peer-reviewed literature on the patterns of earthquake-related injuries in the pediatric population. Methods: On May 14, 2012, the authors performed a systematic review of literature from 1950 to 2012 indexed in Pubmed, EMBASE, Scopus, Web of Science, and Cochrane Library. Articles written in English, providing a quantitative description of pediatric injuries were included. Articles focusing on other types of disasters, geological, surgical, conceptual, psychological, indirect injuries, injury complications such as wound infections and acute kidney injury, case reports, reviews, and non-English articles were excluded. Results: A total of 2037 articles were retrieved, of which only 10 contained quantitative earthquake-related pediatric injury data. All studies were retrospective, had different age categorization, and reported injuries heterogeneously. Only 2 studies reported patterns of injury for all pediatric patients, including patients admitted and discharged. Seven articles described injuries by anatomic location, 5 articles described injuries by type, and 2 articles described injuries using both systems. Conclusions: Differences in age categorization of pediatric patients, and in the injury classification system make quantifying the burden of earthquake-related injuries in the pediatric population difficult. A uniform age categorization and injury classification system are paramount for drawing broader conclusions, enhancing disaster preparation for future disasters, and decreasing morbidity and mortality. PMID:24761308

Longitudinal spatial coherence gated high-resolution tomography and quantitative phase microscopy of biological cells and tissues with uniform illumination

NASA Astrophysics Data System (ADS)

Mehta, Dalip Singh; Ahmad, Azeem; Dubey, Vishesh; Singh, Veena; Butola, Ankit; Mohanty, Tonmoy; Nandi, Sreyankar

2018-02-01

We report longitudinal spatial coherence (LSC) gated high-resolution tomography and quantitative phase microscopy of biological cells and tissues with uniform illumination using laser as a light source. To accomplish this a pseudo thermal light source was synthesized by passing laser beams through an optical system, which is basically a speckle reduction system with combined effect of spatial, temporal, angular and polarisation diversity. The longitudinal spatial coherence length of such light was significantly reduced by synthesizing a pseudo thermal source with the combined effect of spatial, angular and temporal diversity. This results in a low spatially coherent (i.e., broad angular frequency spectrum) light source with narrow temporal frequency spectrum. Light from such a pseudo thermal light source was passed through an interference microscope with varying magnification, such as, 10X and 50X. The interference microscope was used for full-field OCT imaging of multilayer objects and topography of industrial objects. Experimental results of optical sectioning of multilayer biological objects with high axial-resolution less than 10μm was achieved which is comparable to broadband white light source. The synthesized light source with reduced speckles having uniform illumination on the sample, which can be very useful for fluorescence microscopy as well as quantitative phase microscopy with less phase noise. The present system does not require any dispersion compensation optical system for biological samples as a highly monochromatic light source is used.

Do School Uniforms Fit?

ERIC Educational Resources Information Center

White, Kerry A.

2000-01-01

In 1994, Long Beach (California) Unified School District began requiring uniforms in all elementary and middle schools. Now, half of all urban school systems and many suburban schools have uniform policies. Research on uniforms' effectiveness is mixed. Tightened dress codes may be just as effective and less litigious. (MLH)

Coded aperture imaging with uniformly redundant arrays

DOEpatents

Fenimore, Edward E.; Cannon, Thomas M.

1980-01-01

A system utilizing uniformly redundant arrays to image non-focusable radiation. The uniformly redundant array is used in conjunction with a balanced correlation technique to provide a system with no artifacts such that virtually limitless signal-to-noise ratio is obtained with high transmission characteristics. Additionally, the array is mosaicked to reduce required detector size over conventional array detectors.

Coded aperture imaging with uniformly redundant arrays

DOEpatents

Fenimore, Edward E.; Cannon, Thomas M.

1982-01-01

A system utilizing uniformly redundant arrays to image non-focusable radiation. The uniformly redundant array is used in conjunction with a balanced correlation technique to provide a system with no artifacts such that virtually limitless signal-to-noise ratio is obtained with high transmission characteristics. Additionally, the array is mosaicked to reduce required detector size over conventional array detectors.

Student Dress Codes and Uniforms. Research Brief

ERIC Educational Resources Information Center

Johnston, Howard

2009-01-01

According to an Education Commission of the States "Policy Report", research on the effects of dress code and school uniform policies is inconclusive and mixed. Some researchers find positive effects; others claim no effects or only perceived effects. While no state has legislatively mandated the wearing of school uniforms, 28 states and…

77 FR 65164 - Disadvantaged Business Enterprise: Program Implementation Modifications

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-25

... continuous basis, which should also assist with recipients' post-award oversight responsibilities. This NPRM... the Uniform Report of DBE Commitments/Awards and Payments form found in our regulations. As this is an... various modifications to the Uniform Report of DBE Commitments/Awards and Payments form found in Appendix...

Effects of fixture rotation on coating uniformity for high-performance optical filter fabrication

NASA Astrophysics Data System (ADS)

Rubin, Binyamin; George, Jason; Singhal, Riju

2018-04-01

Coating uniformity is critical in fabricating high-performance optical filters by various vacuum deposition methods. Simple and planetary rotation systems with shadow masks are used to achieve the required uniformity [J. B. Oliver and D. Talbot, Appl. Optics 45, 13, 3097 (2006); O. Lyngnes, K. Kraus, A. Ode and T. Erguder, in `Method for Designing Coating Thickness Uniformity Shadow Masks for Deposition Systems with a Planetary Fixture', 2014 Technical Conference Proceedings, Optical Coatings, August 13, 2014, DOI: 10.14332/svc14.proc.1817.]. In this work, we discuss the effect of rotation pattern and speed on thickness uniformity in an ion beam sputter deposition system. Numerical modeling is used to determine statistical distribution of random thickness errors in coating layers. The relationship between thickness tolerance and production yield are simulated theoretically and demonstrated experimentally. Production yields for different optical filters produced in an ion beam deposition system with planetary rotation are presented. Single-wavelength and broadband optical monitoring systems were used for endpoint monitoring during filter deposition. Limitations of thickness tolerances that can be achieved in systems with planetary rotation are shown. Paths for improving production yield in an ion beam deposition system are described.

Determining irrigation distribution uniformity and efficiency for nurseries

Treesearch

R. Thomas Fernandez

2010-01-01

A simple method for testing the distribution uniformity of overhead irrigation systems is described. The procedure is described step-by-step along with an example. Other uses of distribution uniformity testing are presented, as well as common situations that affect distribution uniformity and how to alleviate them.

Counterrotating Propulsive System.

DTIC Science & Technology

1981-12-01

Propellers ," David Taylor Model Basin Report 1342, February 1960. 7. Miller, M.L., " Experimental Determination of Unsteady Forces on Counter- rotating...21. Miller, M.L., " Experimental Determination of Unsteady Forces on Contra- rotating Propellers for Application to Torpedoes," David W. Taylor Naval...pair of counterrotating propellers in a uniform in- flow is given by Reference [14] with the same results. On the

Unleashing Our Untapped Domestic Collection is the Key to Prevention

DTIC Science & Technology

2007-09-01

Information Center (NCIC), Uniform Crime Reporting (UCR), and Integrated Automated Fingerprint Identification System (IAFIS) fingerprint ...The Blue Ocean Strategy Canvas , as described by Kim and Mauborgne, is an analytical framework that is both diagnostic and action oriented...The authors argue the value of a strategy canvas is its ability to capture the current state, provide an understanding of various factors impacting

Synergistic Approach Integrating Joint Capabilities for USSOCOM Contingency Contracting: Construction Management Module

DTIC Science & Technology

2010-12-01

59 a. The Joint Uniform Lessons Learned System (JULLS) .........59 b. Acquisition Community Connection (ACC) ..........................59 c...Report ACC Acquisition Community Connection ADDIE Analyze, Design, Develop, Implement, Evaluate AFFARS Air Force Federal Acquisition Regulation...Operations J4 Logistics J5 Plans J6 Communications J8 Programming and Comptroller J&A Justification and Approval JARB Joint Acquisition

12 CFR 8.6 - Fees for special examinations and investigations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... receives a composite rating of 3 under the Uniform Financial Institutions Rating System (UFIRS) at its most recent examination and by 2.0 for each bank that receives a composite UFIRS rating of 4 or 5 at such... related assets are those assets reported on Schedule RC-T of FFIEC Forms 031 and 041, Line 10 (columns A...

12 CFR 8.6 - Fees for special examinations and investigations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... receives a composite rating of 3 under the Uniform Financial Institutions Rating System (UFIRS) at its most recent examination and by 2.0 for each bank that receives a composite UFIRS rating of 4 or 5 at such... related assets are those assets reported on Schedule RC-T of FFIEC Forms 031 and 041, Line 10 (columns A...

12 CFR 8.6 - Fees for special examinations and investigations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... receives a composite rating of 3 under the Uniform Financial Institutions Rating System (UFIRS) at its most recent examination and by 2.0 for each bank that receives a composite UFIRS rating of 4 or 5 at such... related assets are those assets reported on Schedule RC-T of FFIEC Forms 031 and 041, Line 10 (columns A...

Care of the poor: a story worth telling. A system speaks up and says what it means.

PubMed

Kelly, C J

1989-09-01

Traditionally, those in Catholic healthcare have considered it bad taste to "toot your own horn" for anything done on behalf of the poor. Such reticence was admirable and reasonable in a stable environment, but a turbulent environment requires more assertiveness. Today, healthcare is a whole new game, with new ground rules. It behooves all players to be more critical of all they do, even when "doing good." The Sisters of Charity Health Care Systems (SCHCS), Inc., Cincinnati, established its Task Force for the Poor to explore and initiate new ways to address the needs of the poor, to find strategies for new forms of service, and to develop mechanisms to evaluate those new services and report the results. But with 22 acute care institutions serving different markets in six states, SCHCS had to establish some uniformity to plan, budget, audit, and report the entire spectrum of its charitable activities. The task force proposed developing uniform measures (definitions) of the charity care provided in traditional inpatient and outpatient settings, as well as that provided through services on behalf of the poor but not captured by standard accounting measures.

Experimental test of photonic entanglement in accelerated reference frames

NASA Astrophysics Data System (ADS)

Fink, Matthias; Rodriguez-Aramendia, Ana; Handsteiner, Johannes; Ziarkash, Abdul; Steinlechner, Fabian; Scheidl, Thomas; Fuentes, Ivette; Pienaar, Jacques; Ralph, Timothy C.; Ursin, Rupert

2017-05-01

The unification of the theory of relativity and quantum mechanics is a long-standing challenge in contemporary physics. Experimental techniques in quantum optics have only recently reached the maturity required for the investigation of quantum systems under the influence of non-inertial motion, such as being held at rest in gravitational fields, or subjected to uniform accelerations. Here, we report on experiments in which a genuine quantum state of an entangled photon pair is exposed to a series of different accelerations. We measure an entanglement witness for g-values ranging from 30 mg to up to 30 g--under free-fall as well on a spinning centrifuge--and have thus derived an upper bound on the effects of uniform acceleration on photonic entanglement.

Experimental test of photonic entanglement in accelerated reference frames.

PubMed

Fink, Matthias; Rodriguez-Aramendia, Ana; Handsteiner, Johannes; Ziarkash, Abdul; Steinlechner, Fabian; Scheidl, Thomas; Fuentes, Ivette; Pienaar, Jacques; Ralph, Timothy C; Ursin, Rupert

2017-05-10

The unification of the theory of relativity and quantum mechanics is a long-standing challenge in contemporary physics. Experimental techniques in quantum optics have only recently reached the maturity required for the investigation of quantum systems under the influence of non-inertial motion, such as being held at rest in gravitational fields, or subjected to uniform accelerations. Here, we report on experiments in which a genuine quantum state of an entangled photon pair is exposed to a series of different accelerations. We measure an entanglement witness for g-values ranging from 30 mg to up to 30 g-under free-fall as well on a spinning centrifuge-and have thus derived an upper bound on the effects of uniform acceleration on photonic entanglement.

Evaluation of fuel preparation systems for lean premixing-prevaporizing combustors

NASA Technical Reports Server (NTRS)

Dodds, W. J.; Ekstedt, E. E.

1985-01-01

A series of experiments was carried out in order to produce design data for a premixing prevaporizing fuel-air mixture preparation system for aircraft gas turbine engine combustors. The fuel-air mixture uniformity of four different system design concepts was evaluated over a range of conditions representing the cruise operation of a modern commercial turbofan engine. Operating conditions including pressure, temperature, fuel-to-air ratio, and velocity, exhibited no clear effect on mixture uniformity of systems using pressure-atomizing fuel nozzles and large-scale mixing devices. However, the performance of systems using atomizing fuel nozzles and large-scale mixing devices was found to be sensitive to operating conditions. Variations in system design variables were also evaluated and correlated. Mixing uniformity was found to improve with system length, pressure drop, and the number of fuel injection points per unit area. A premixing system capable of providing mixing uniformity to within 15 percent over a typical range of cruise operating conditions is demonstrated.

Fiber grating system used to measure strain in a 22-ft composite utility pole

NASA Astrophysics Data System (ADS)

Udd, Eric; Corona, Kelli; Slattery, Kerry T.; Dorr, Donald J.

1996-05-01

Composite utility poles have significant advantages with respect to wooden utility poles that include superior strength and uniformity, light weight for ease of deployment, the ability to be recycled reducing hazardous waste associated with chemically treated wooden poles, and compatibility with embedded fiber optic sensors allowing structural loads to be monitored. This paper reports tests conducted of fiber optic grating sensors in combination with an overcoupled coupler demodulation system to support structural testing of a 22 foot composite pole.

"Recommendations for uniform reporting of data following major trauma--the Utstein style" (as of July 17, 1999). An International Trauma Anaesthesia and Critical Care Society (ITACCS).

PubMed

Dick, W F; Baskett, P J; Grande, C; Delooz, H; Kloeck, W; Lackner, C; Lipp, M; Mauritz, W; Nerlich, M; Nicholl, J; Nolan, J; Oakley, P; Parr, M; Seekamp, A; Soreide, E; Steen, P A; van Camp, L; Wolcke, B; Yates, D

2000-01-01

Basic and advanced care of trauma patients has always been an important aspect of prehospital and immediate in-hospital emergency medicine, involving a broad spectrum of disciplines, specialties and skills delivered through Emergency Medical Services Systems which, however, may differ significantly in structure, resources and operation. This complex background has, at least in part, hindered the development of a uniform pattern or set of criteria and definitions. This in turn has hitherto rendered data incompatible, with the consequence that such differing systems or protocols of care cannot be readily evaluated or compared with acceptable validity. Guided by previous consensus processes evolved by the ERC, the AHA and other International Organizations--represented in ILCOR--on 'Uniform reporting of data following out-of-hospital and in-hospital cardiac arrest--the Utstein style' an international working group of ITACCS has drafted a document, 'Recommendations for uniform reporting of data following major trauma--the Utstein style'. The reporting system is based on the following considerations: A structured reporting system based on an "Utstein style template" which would permit the compilation of data and statistics on major trauma care, facilitating and validating independent or comparative audit of performance and quality of care (and enable groups to challenge performance statistics which did not take account of all relevant information). The recommendations and template should encompass both out-of-hospital and in-hospital trauma care. The recommendations and template should further permit intra- and inter-system evaluation to improve the quality of delivered care and identification of the relative benefits of different systems and innovative initiatives. The template should facilitate studies setting out to improve epidemiological understanding of trauma; for example such studies might focus on the factors that determine survival. The document is structured along the lines of the original Utstein Style Guidelines publication on 'prehospital cardiac arrest'. It includes a glossary of terms used in the prehospital and early hospital phase and definitions, time points and intervals. The document uses an almost identical scheme for illustrating the different process time clocks--one for the patient, one for the dispatch centre, one for the ambulance and, finally, one for the hospital. For clarity, data should be reported as core data (i.e. always obtained) and optional data (obtained under specific circumstances). In contrast to the graphic approach used for the Utstein template for pre- or in-hospital cardiac arrest, respectively, the present template introduces, for the time being, at least, a number of terms and definitions and a semantic rather than a graphic report form. The document includes the following sections: The Section Introduction and background The Section on Trauma Data Structure Development: presents a general outline of the development of structured data using object-orientated modelling (which will be discussed in due course) and includes a set of explanatory illustrations. The Section on Terms and Definitions: outlines terms and definitions in trauma care, describing different types of trauma (blunt, penetrating, long bone, major/combined, multiple/polytrauma and predominant trauma). The Section on Factors relating to the circumstances of the injury describes the following items: cause of injury (e.g. type of injury (blunt or penetrating), burns, cold, crush, laceration, amputation, radiation, multiple, etc. Severity of Injury e.g. prehospital basic abbreviated injury score developed by the working group. The score contains anatomical and physiological disability data, with the anatomical scale ranging ordinally from 1. Head to 9. External; the physiological disability scale ranging ordinally from 0--unsurvivable. Mechanism of injury recording for transportation incidents etc. e.g. the type of impact, po

The Relationship of School Uniforms to Student Attendance, Achievement, and Discipline

ERIC Educational Resources Information Center

Sowell, Russell Edward

2012-01-01

This causal-comparative study examined the relationship of school uniforms to attendance, academic achievement, and discipline referral rates, using data collected from two high schools in rural southwest Georgia county school systems, one with a uniforms program and one without a uniforms program. After accounting for race and students with…

[Structured quality report of urologic clinics according to section 137 SGB V. Useful information for the patient, marketing tool of the hospitals, leverage wielded by the health insurance companies, or junk data?].

PubMed

Volkmer, B; Petschl, S; Härtel, M; Bopp, G; Herkommer, K; Gschwend, J

2006-04-01

In 2005, German hospitals were legally obliged to publish a structured quality report on their data of 2004 including the top 10 diagnosis-related groups, top 10 diagnoses, and top 10 procedures for every specialty. The aim was to increase the transparency for patients, doctors, and health insurance companies. Comparing the quality reports of 248 departments of urology revealed very uniform distributions of diagnoses and diagnosis-related groups. There was a large variety of top 10 procedures, resulting from different interpretations of the coding system, leading to diminished accuracy. The quality reports provide coding specialists with important data, but for patients and nonspecialized doctors, this system is not helpful in improving transparency.

An Analysis of Non-Uniform Stress States in Finite Thin Film/Substrate System: The Need of Full-Field Curvature Measurements

ERIC Educational Resources Information Center

Ngo, Duc Minh

2009-01-01

Current methodologies used for the inference of thin film stresses through curvatures are strictly restricted to stress and curvature states which are assumed to remain uniform over the entire film/substrate system. In this dissertation, we extend these methodologies to non-uniform stress and curvature states for the single layer of thin film or…

7 CFR 1770.12 - Supplementary accounts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURE (CONTINUED) ACCOUNTING REQUIREMENTS FOR RUS TELECOMMUNICATIONS BORROWERS Uniform System of... shall be changed to conform with the State's accounting system. (b) In addition to the accounts set... Uniform System of Accounts. In those instances in which a State regulatory body having jurisdiction over...

[Data coding in the Israeli healthcare system - do choices provide the answers to our system's needs?].

PubMed

Zelingher, Julian; Ash, Nachman

2013-05-01

The IsraeLi healthcare system has undergone major processes for the adoption of health information technologies (HIT), and enjoys high Levels of utilization in hospital and ambulatory care. Coding is an essential infrastructure component of HIT, and ts purpose is to represent data in a simplified and common format, enhancing its manipulation by digital systems. Proper coding of data enables efficient identification, storage, retrieval and communication of data. UtiLization of uniform coding systems by different organizations enables data interoperability between them, facilitating communication and integrating data elements originating in different information systems from various organizations. Current needs in Israel for heaLth data coding include recording and reporting of diagnoses for hospitalized patients, outpatients and visitors of the Emergency Department, coding of procedures and operations, coding of pathology findings, reporting of discharge diagnoses and causes of death, billing codes, organizational data warehouses and national registries. New national projects for cLinicaL data integration, obligatory reporting of quality indicators and new Ministry of Health (MOH) requirements for HIT necessitate a high Level of interoperability that can be achieved only through the adoption of uniform coding. Additional pressures were introduced by the USA decision to stop the maintenance of the ICD-9-CM codes that are also used by Israeli healthcare, and the adoption of ICD-10-C and ICD-10-PCS as the main coding system for billing purpose. The USA has also mandated utilization of SNOMED-CT as the coding terminology for the ELectronic Health Record problem list, and for reporting quality indicators to the CMS. Hence, the Israeli MOH has recently decided that discharge diagnoses will be reported using ICD-10-CM codes, and SNOMED-CT will be used to code the cLinical information in the EHR. We reviewed the characteristics, strengths and weaknesses of these two coding systems. In summary, the adoption of ICD-10-CM is in line with the USA decision to abandon ICD-9-CM, and the Israeli heaLthcare system could benefit from USA heaLthcare efforts in this direction. The Large content of SNOMED-CT and its sophisticated hierarchical data structure will enable advanced cLinicaL decision support and quality improvement applications.

Nonimaging solar concentrator with near-uniform irradiance for photovoltaic arrays

NASA Astrophysics Data System (ADS)

O'Gallagher, Joseph J.; Winston, Roland; Gee, Randy

2001-11-01

We report results of a study our group has undertaken to design a solar concentrator with uniform irradiance on a planar target. This attribute is especially important for photovoltaic concentrators. We find that a variety of optical mixers, some incorporating a moderate level of concentration, can be quite effective in achieving near uniform irradiance.

School Dress Codes and Uniform Policies.

ERIC Educational Resources Information Center

Anderson, Wendell

2002-01-01

Opinions abound on what students should wear to class. Some see student dress as a safety issue; others see it as a student-rights issue. The issue of dress codes and uniform policies has been tackled in the classroom, the boardroom, and the courtroom. This Policy Report examines the whole fabric of the debate on dress codes and uniform policies…

42 CFR 137.204 - How will this voluntary national uniform data set be developed?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false How will this voluntary national uniform data set... HUMAN SERVICES INDIAN HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES TRIBAL SELF-GOVERNANCE Operational Provisions Health Status Reports § 137.204 How will this voluntary national uniform data set be...

Robust uniform persistence in discrete and continuous dynamical systems using Lyapunov exponents.

PubMed

Salceanu, Paul L

2011-07-01

This paper extends the work of Salceanu and Smith [12, 13] where Lyapunov exponents were used to obtain conditions for uniform persistence ina class of dissipative discrete-time dynamical systems on the positive orthant of R(m), generated by maps. Here a united approach is taken, for both discrete and continuous time, and the dissipativity assumption is relaxed. Sufficient conditions are given for compact subsets of an invariant part of the boundary of R(m+) to be robust uniform weak repellers. These conditions require Lyapunov exponents be positive on such sets. It is shown how this leads to robust uniform persistence. The results apply to the investigation of robust uniform persistence of the disease in host populations, as shown in an application.

Guillain–Barre syndrome following quadrivalent human papillomavirus vaccination among vaccine-eligible individuals in the United States

PubMed Central

Ojha, Rohit P; Jackson, Bradford E; Tota, Joseph E; Offutt-Powell, Tabatha N; Singh, Karan P; Bae, Sejong

2014-01-01

Post-marketing surveillance studies provide conflicting evidence about whether Guillain–Barre syndrome occurs more frequently following quadrivalent human papillomavirus (HPV4) vaccination. We aimed to assess whether Guillain–Barre syndrome is reported more frequently following HPV4 vaccination than other vaccinations among females and males aged 9 to 26 y in the United States. We used adverse event reports received by the United States Vaccine Adverse Event Reporting System (VAERS) between January 1, 2010 and December 31, 2012 to estimate overall, age-, and sex-specific proportional reporting ratios (PRRs) and corresponding Χ2 values for reports of Guillain–Barre syndrome between 5 and 42 d following HPV vaccination. Minimum criteria for a signal using this approach are 3 or more cases, PRR ≥2, and Χ2 ≥ 4. Guillain–Barre syndrome was listed as an adverse event in 45 of 14 822 reports, of which 9 reports followed HPV4 vaccination and 36 reports followed all other vaccines. The overall, age-, and sex-specific PRR estimates were uniformly below 1. In addition, the overall, age-, and sex-specific Χ2 values were uniformly below 3. Our analysis of post-marketing surveillance data does not suggest that Guillain–Barre syndrome is reported more frequently following HPV4 vaccination than other vaccinations among vaccine-eligible females or males in the United States. Our findings may be useful when discussing the risks and benefits of HPV4 vaccination. PMID:24013368

Guillain-Barre syndrome following quadrivalent human papillomavirus vaccination among vaccine-eligible individuals in the United States.

PubMed

Ojha, Rohit P; Jackson, Bradford E; Tota, Joseph E; Offutt-Powell, Tabatha N; Singh, Karan P; Bae, Sejong

2014-01-01

Post-marketing surveillance studies provide conflicting evidence about whether Guillain-Barre syndrome occurs more frequently following quadrivalent human papillomavirus (HPV4) vaccination. We aimed to assess whether Guillain-Barre syndrome is reported more frequently following HPV4 vaccination than other vaccinations among females and males aged 9 to 26 y in the United States. We used adverse event reports received by the United States Vaccine Adverse Event Reporting System (VAERS) between January 1, 2010 and December 31, 2012 to estimate overall, age-, and sex-specific proportional reporting ratios (PRRs) and corresponding Χ2 values for reports of Guillain-Barre syndrome between 5 and 42 d following HPV vaccination. Minimum criteria for a signal using this approach are 3 or more cases, PRR≥2, and Χ2≥4. Guillain-Barre syndrome was listed as an adverse event in 45 of 14,822 reports, of which 9 reports followed HPV4 vaccination and 36 reports followed all other vaccines. The overall, age-, and sex-specific PRR estimates were uniformly below 1. In addition, the overall, age-, and sex-specific Χ2 values were uniformly below 3. Our analysis of post-marketing surveillance data does not suggest that Guillain-Barre syndrome is reported more frequently following HPV4 vaccination than other vaccinations among vaccine-eligible females or males in the United States. Our findings may be useful when discussing the risks and benefits of HPV4 vaccination.

23 CFR 1235.1 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-04-01

... UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.1 Purpose. The purpose of this part is to provide guidelines to States for the establishment of a uniform system for handicapped parking for persons...

23 CFR 1235.1 - Purpose.

Code of Federal Regulations, 2014 CFR

2014-04-01

... UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.1 Purpose. The purpose of this part is to provide guidelines to States for the establishment of a uniform system for handicapped parking for persons...

23 CFR 1235.1 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-04-01

... UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.1 Purpose. The purpose of this part is to provide guidelines to States for the establishment of a uniform system for handicapped parking for persons...

23 CFR 1235.1 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-04-01

... UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.1 Purpose. The purpose of this part is to provide guidelines to States for the establishment of a uniform system for handicapped parking for persons...

23 CFR 1235.1 - Purpose.

Code of Federal Regulations, 2013 CFR

2013-04-01

... UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.1 Purpose. The purpose of this part is to provide guidelines to States for the establishment of a uniform system for handicapped parking for persons...

49 CFR Appendix A to Part 23 - Uniform Report of ACDBE Participation

Code of Federal Regulations, 2011 CFR

2011-10-01

... BUSINESS ENTERPRISE IN AIRPORT CONCESSIONS Pt. 23, App. A Appendix A to Part 23—Uniform Report of ACDBE... purchased by the airport itself or by concessionaires and management contractors from certified DBEs. Block... concessionaires (prime and sub) and purchases of goods and services (ACDBE and non-ACDBE combined) at the airport...

49 CFR Appendix A to Part 23 - Uniform Report of ACDBE Participation

Code of Federal Regulations, 2010 CFR

2010-10-01

... BUSINESS ENTERPRISE IN AIRPORT CONCESSIONS Pt. 23, App. A Appendix A to Part 23—Uniform Report of ACDBE... purchased by the airport itself or by concessionaires and management contractors from certified DBEs. Block... concessionaires (prime and sub) and purchases of goods and services (ACDBE and non-ACDBE combined) at the airport...

Report of the 2016 Uniform Regional Scab Nursery for spring wheat parents

USDA-ARS?s Scientific Manuscript database

The Uniform Regional Scab Nursery for Spring Wheat Parents (URSN) was grown for the 21st year in 2016. Five locations (Brookings, SD, St. Paul and Crookston, MN, Prosper, ND, and Morden, Canada) reported results. A total of 33 entries was included in the 2016 URSN, in addition to the resistant chec...

Convergence of the Full Compressible Navier-Stokes-Maxwell System to the Incompressible Magnetohydrodynamic Equations in a Bounded Domain II: Global Existence Case

NASA Astrophysics Data System (ADS)

Fan, Jishan; Li, Fucai; Nakamura, Gen

2018-06-01

In this paper we continue our study on the establishment of uniform estimates of strong solutions with respect to the Mach number and the dielectric constant to the full compressible Navier-Stokes-Maxwell system in a bounded domain Ω \\subset R^3. In Fan et al. (Kinet Relat Models 9:443-453, 2016), the uniform estimates have been obtained for large initial data in a short time interval. Here we shall show that the uniform estimates exist globally if the initial data are small. Based on these uniform estimates, we obtain the convergence of the full compressible Navier-Stokes-Maxwell system to the incompressible magnetohydrodynamic equations for well-prepared initial data.

In situ process monitoring in selective laser sintering using optical coherence tomography

NASA Astrophysics Data System (ADS)

Gardner, Michael R.; Lewis, Adam; Park, Jongwan; McElroy, Austin B.; Estrada, Arnold D.; Fish, Scott; Beaman, Joseph J.; Milner, Thomas E.

2018-04-01

Selective laser sintering (SLS) is an efficient process in additive manufacturing that enables rapid part production from computer-based designs. However, SLS is limited by its notable lack of in situ process monitoring when compared with other manufacturing processes. We report the incorporation of optical coherence tomography (OCT) into an SLS system in detail and demonstrate access to surface and subsurface features. Video frame rate cross-sectional imaging reveals areas of sintering uniformity and areas of excessive heat error with high temporal resolution. We propose a set of image processing techniques for SLS process monitoring with OCT and report the limitations and obstacles for further OCT integration with SLS systems.

Logical optimization for database uniformization

NASA Technical Reports Server (NTRS)

Grant, J.

1984-01-01

Data base uniformization refers to the building of a common user interface facility to support uniform access to any or all of a collection of distributed heterogeneous data bases. Such a system should enable a user, situated anywhere along a set of distributed data bases, to access all of the information in the data bases without having to learn the various data manipulation languages. Furthermore, such a system should leave intact the component data bases, and in particular, their already existing software. A survey of various aspects of the data bases uniformization problem and a proposed solution are presented.

Non-uniformity calibration for MWIR polarization imagery obtained with integrated microgrid polarimeters

NASA Astrophysics Data System (ADS)

Liu, Hai-Zheng; Shi, Ze-Lin; Feng, Bin; Hui, Bin; Zhao, Yao-Hong

2016-03-01

Integrating microgrid polarimeters on focal plane array (FPA) of an infrared detector causes non-uniformity of polarization response. In order to reduce the effect of polarization non-uniformity, this paper constructs an experimental setup for capturing raw flat-field images and proposes a procedure for acquiring non-uniform calibration (NUC) matrix and calibrating raw polarization images. The proposed procedure takes the incident radiation as a polarization vector and offers a calibration matrix for each pixel. Both our matrix calibration and two-point calibration are applied to our mid-wavelength infrared (MWIR) polarization imaging system with integrated microgrid polarimeters. Compared with two point calibration, our matrix calibration reduces non-uniformity by 30 40% under condition of flat-field data test with polarization. The ourdoor scene observation experiment indicates that our calibration can effectively reduce polarization non-uniformity and improve the image quality of our MWIR polarization imaging system.

2008 Post-Election Voting Survey of Uniformed Service Members: Stastical Methodology Report

DTIC Science & Technology

2009-08-01

Research Fellow assisted in formatting this report. Data Recognition Corporation (DRC) performed data collection and editing. DMDC’s Survey...METHODOLOGY REPORT Executive Summary The Uniformed and Overseas Citizens Absentee Voting Act of 1986 (UOCAVA), 42 USC 1973ff, permits members of...citizens covered by UOCAVA, (2) to assess the impact of the FVAP’s efforts to simplify and ease the process of voting absentee , (3) to evaluate other

41 CFR 101-30.103-1 - General.

Code of Federal Regulations, 2014 CFR

2014-07-01

... System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 30-FEDERAL CATALOG SYSTEM 30.1... and maintain a uniform Federal Catalog System to identify and classify personal property under the control of Federal agencies. Under this law each Federal agency is required to utilize the uniform Federal...

41 CFR 101-30.103-1 - General.

Code of Federal Regulations, 2011 CFR

2011-07-01

... System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 30-FEDERAL CATALOG SYSTEM 30.1... and maintain a uniform Federal Catalog System to identify and classify personal property under the control of Federal agencies. Under this law each Federal agency is required to utilize the uniform Federal...

41 CFR 101-30.103-1 - General.

Code of Federal Regulations, 2012 CFR

2012-07-01

... System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 30-FEDERAL CATALOG SYSTEM 30.1... and maintain a uniform Federal Catalog System to identify and classify personal property under the control of Federal agencies. Under this law each Federal agency is required to utilize the uniform Federal...

41 CFR 101-30.103-1 - General.

Code of Federal Regulations, 2013 CFR

2013-07-01

... System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 30-FEDERAL CATALOG SYSTEM 30.1... and maintain a uniform Federal Catalog System to identify and classify personal property under the control of Federal agencies. Under this law each Federal agency is required to utilize the uniform Federal...

Uniform emergency codes: will they improve safety?

PubMed

2005-01-01

There are pros and cons to uniform code systems, according to emergency medicine experts. Uniformity can be a benefit when ED nurses and other staff work at several facilities. It's critical that your staff understand not only what the codes stand for, but what they must do when codes are called. If your state institutes a new system, be sure to hold regular drills to familiarize your ED staff.

Diagnosing Trouble Spots Caused by an Irrigation System

Treesearch

John R. Scholtes

2002-01-01

I discuss a testing procedure to determine the water distribution pattern of a sprinkler irrigation system and steps that may be taken to improve uniformity of application. All irrigation systems require testing and maintenance to assure that water application is as uniform as possible. Even new systems installed to a manufacturer's specifications should be "...

Improving the uniformity of luminous system in radial imaging capsule endoscope system

NASA Astrophysics Data System (ADS)

Ou-Yang, Mang; Jeng, Wei-De

2013-02-01

This study concerns the illumination system in a radial imaging capsule endoscope (RICE). Uniformly illuminating the object is difficult because the intensity of the light from the light emitting diodes (LEDs) varies with angular displacement. When light is emitted from the surface of the LED, it first encounters the cone mirror, from which it is reflected, before directly passing through the lenses and complementary metal oxide semiconductor (CMOS) sensor. The light that is strongly reflected from the transparent view window (TVW) propagates again to the cone mirror, to be reflected and to pass through the lenses and CMOS sensor. The above two phenomena cause overblooming on the image plane. Overblooming causes nonuniform illumination on the image plane and consequently reduced image quality. In this work, optical design software was utilized to construct a photometric model for the optimal design of the LED illumination system. Based on the original RICE model, this paper proposes an optimal design to improve the uniformity of the illumination. The illumination uniformity in the RICE is increased from its original value of 0.128 to 0.69, greatly improving light uniformity.

Isospectrals of non-uniform Rayleigh beams with respect to their uniform counterparts

PubMed Central

Ganguli, Ranjan

2018-01-01

In this paper, we look for non-uniform Rayleigh beams isospectral to a given uniform Rayleigh beam. Isospectral systems are those that have the same spectral properties, i.e. the same free vibration natural frequencies for a given boundary condition. A transformation is proposed that converts the fourth-order governing differential equation of non-uniform Rayleigh beam into a uniform Rayleigh beam. If the coefficients of the transformed equation match with those of the uniform beam equation, then the non-uniform beam is isospectral to the given uniform beam. The boundary-condition configuration should be preserved under this transformation. We present the constraints under which the boundary configurations will remain unchanged. Frequency equivalence of the non-uniform beams and the uniform beam is confirmed by the finite-element method. For the considered cases, examples of beams having a rectangular cross section are presented to show the application of our analysis. PMID:29515879

A chirped-pulse Fourier-transform microwave/pulsed uniform flow spectrometer. II. Performance and applications for reaction dynamics.

PubMed

Abeysekera, Chamara; Zack, Lindsay N; Park, G Barratt; Joalland, Baptiste; Oldham, James M; Prozument, Kirill; Ariyasingha, Nuwandi M; Sims, Ian R; Field, Robert W; Suits, Arthur G

2014-12-07

This second paper in a series of two reports on the performance of a new instrument for studying chemical reaction dynamics and kinetics at low temperatures. Our approach employs chirped-pulse Fourier-transform microwave (CP-FTMW) spectroscopy to probe photolysis and bimolecular reaction products that are thermalized in pulsed uniform flows. Here we detail the development and testing of a new K(a)-band CP-FTMW spectrometer in combination with the pulsed flow system described in Paper I [J. M. Oldham, C. Abeysekera, B. Joalland, L. N. Zack, K. Prozument, I. R. Sims, G. B. Park, R. W. Field, and A. G. Suits, J. Chem. Phys. 141, 154202 (2014)]. This combination delivers broadband spectra with MHz resolution and allows monitoring, on the μs timescale, of the appearance of transient reaction products. Two benchmark reactive systems are used to illustrate and characterize the performance of this new apparatus: the photodissociation of SO2 at 193 nm, for which the vibrational populations of the SO product are monitored, and the reaction between CN and C2H2, for which the HCCCN product is detected in its vibrational ground state. The results show that the combination of these two well-matched techniques, which we refer to as chirped-pulse in uniform flow, also provides insight into the vibrational and rotational relaxation kinetics of the nascent reaction products. Future directions are discussed, with an emphasis on exploring the low temperature chemistry of complex polyatomic systems.

LWIR pupil imaging and prospects for background compensation

NASA Astrophysics Data System (ADS)

LeVan, Paul; Sakoglu, Ünal; Stegall, Mark; Pierce, Greg

2015-08-01

A previous paper described LWIR Pupil Imaging with a sensitive, low-flux focal plane array, and behavior of this type of system for higher flux operations as understood at the time. We continue this investigation, and report on a more detailed characterization of the system over a broad range of pixel fluxes. This characterization is then shown to enable non-uniformity correction over the flux range, using a standard approach. Since many commercial tracking platforms include a "guider port" that accepts pulse width modulation (PWM) error signals, we have also investigated a variation on the use of this port to "dither" the tracking platform in synchronization with the continuous collection of infrared images. The resulting capability has a broad range of applications that extend from generating scene motion in the laboratory for quantifying performance of "realtime, scene-based non-uniformity correction" approaches, to effectuating subtraction of bright backgrounds by alternating viewing aspect between a point source and adjacent, source-free backgrounds.

Characterization of total ionizing dose damage in COTS pinned photodiode CMOS image sensors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zujun, E-mail: wangzujun@nint.ac.cn; Ma, Wuying; Huang, Shaoyan

The characterization of total ionizing dose (TID) damage in COTS pinned photodiode (PPD) CMOS image sensors (CISs) is investigated. The radiation experiments are carried out at a {sup 60}Co γ-ray source. The CISs are produced by 0.18-μm CMOS technology and the pixel architecture is 8T global shutter pixel with correlated double sampling (CDS) based on a 4T PPD front end. The parameters of CISs such as temporal domain, spatial domain, and spectral domain are measured at the CIS test system as the EMVA 1288 standard before and after irradiation. The dark current, random noise, dark signal non-uniformity (DSNU), photo responsemore » non-uniformity (PRNU), overall system gain, saturation output, dynamic range (DR), signal to noise ratio (SNR), quantum efficiency (QE), and responsivity versus the TID are reported. The behaviors of the tested CISs show remarkable degradations after radiation. The degradation mechanisms of CISs induced by TID damage are also analyzed.« less

The Muon g - 2 experiment at Fermilab

NASA Astrophysics Data System (ADS)

Mott, James; Muon g - 2 experiment

2017-06-01

The Muon g - 2 experiment at Fermilab will measure the anomalous magnetic moment of the muon to a precision of 140 ppb, reducing the experimental uncertainty by a factor of 4 compared to the previous measurement at BNL (E821). The measurement technique adopts the storage ring concept used for E821, with magic-momentum muons stored in a highly uniform 1.45 T magnetic dipole field. The spin precession frequency is extracted from an analysis of the modulation of the rate of higher-energy positrons from muon decays, detected by 24 calorimeters and 3 straw tracking detectors. Compared to the E821 experiment, muon beam preparation, storage ring internal hardware, field measuring equipment, and detector and electronics systems are all new or significantly upgraded. Herein, I report on the status of the experiment as of Sept. 2016, presenting the magnetic field uniformity results after the completion of the first round of shimming and outlining the construction progress of the main detector systems.

The Muon g $-$ 2 experiment at Fermilab

DOE PAGES

Mott, James

2017-06-21

Here, the Muon g-2 experiment at Fermilab will measure the anomalous magnetic moment of the muon to a precision of 140 ppb, reducing the experimental uncertainty by a factor of 4 compared to the previous measurement at BNL (E821). The measurement technique adopts the storage ring concept used for E821, with magic-momentum muons stored in a highly uniform 1.45 T magnetic dipole field. The spin precession frequency is extracted from an analysis of the modulation of the rate of higher-energy positrons from muon decays, detected by 24 calorimeters and 3 straw tracking detectors. Compared to the E821 experiment, muon beammore » preparation, storage ring internal hardware, field measuring equipment, and detector and electronics systems are all new or significantly upgraded. Herein, I report on the status of the experiment as of Sept. 2016, presenting the magnetic field uniformity results after the completion of the first round of shimming and outlining the construction progress of the main detector systems.« less

Characterization of total ionizing dose damage in COTS pinned photodiode CMOS image sensors

NASA Astrophysics Data System (ADS)

Wang, Zujun; Ma, Wuying; Huang, Shaoyan; Yao, Zhibin; Liu, Minbo; He, Baoping; Liu, Jing; Sheng, Jiangkun; Xue, Yuan

2016-03-01

The characterization of total ionizing dose (TID) damage in COTS pinned photodiode (PPD) CMOS image sensors (CISs) is investigated. The radiation experiments are carried out at a 60Co γ-ray source. The CISs are produced by 0.18-μm CMOS technology and the pixel architecture is 8T global shutter pixel with correlated double sampling (CDS) based on a 4T PPD front end. The parameters of CISs such as temporal domain, spatial domain, and spectral domain are measured at the CIS test system as the EMVA 1288 standard before and after irradiation. The dark current, random noise, dark signal non-uniformity (DSNU), photo response non-uniformity (PRNU), overall system gain, saturation output, dynamic range (DR), signal to noise ratio (SNR), quantum efficiency (QE), and responsivity versus the TID are reported. The behaviors of the tested CISs show remarkable degradations after radiation. The degradation mechanisms of CISs induced by TID damage are also analyzed.

The Muon g $-$ 2 experiment at Fermilab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mott, James

Here, the Muon g-2 experiment at Fermilab will measure the anomalous magnetic moment of the muon to a precision of 140 ppb, reducing the experimental uncertainty by a factor of 4 compared to the previous measurement at BNL (E821). The measurement technique adopts the storage ring concept used for E821, with magic-momentum muons stored in a highly uniform 1.45 T magnetic dipole field. The spin precession frequency is extracted from an analysis of the modulation of the rate of higher-energy positrons from muon decays, detected by 24 calorimeters and 3 straw tracking detectors. Compared to the E821 experiment, muon beammore » preparation, storage ring internal hardware, field measuring equipment, and detector and electronics systems are all new or significantly upgraded. Herein, I report on the status of the experiment as of Sept. 2016, presenting the magnetic field uniformity results after the completion of the first round of shimming and outlining the construction progress of the main detector systems.« less

Experimental test of photonic entanglement in accelerated reference frames

PubMed Central

Fink, Matthias; Rodriguez-Aramendia, Ana; Handsteiner, Johannes; Ziarkash, Abdul; Steinlechner, Fabian; Scheidl, Thomas; Fuentes, Ivette; Pienaar, Jacques; Ralph, Timothy C.; Ursin, Rupert

2017-01-01

The unification of the theory of relativity and quantum mechanics is a long-standing challenge in contemporary physics. Experimental techniques in quantum optics have only recently reached the maturity required for the investigation of quantum systems under the influence of non-inertial motion, such as being held at rest in gravitational fields, or subjected to uniform accelerations. Here, we report on experiments in which a genuine quantum state of an entangled photon pair is exposed to a series of different accelerations. We measure an entanglement witness for g-values ranging from 30 mg to up to 30 g—under free-fall as well on a spinning centrifuge—and have thus derived an upper bound on the effects of uniform acceleration on photonic entanglement. PMID:28489082

Transition from single to multiple axial potential structure in expanding helicon plasma

NASA Astrophysics Data System (ADS)

Ghosh, Soumen; Chattopadhyay, P. K.; Ghosh, J.; Pal, R.; Bora, D.

2017-02-01

Transition from single to multiple axial potential structure (MAPS) formation is reported in expanding helicon plasma. This transition is created by forming a cusp magnetic field at the downstream after the expansion throat. Two distinct potential drops are separated by a uniform axial potential zone. Non-uniform axial density distribution exists in expanding helicon systems. A cusp-like field nourishes both the axial density gradients sufficient enough for the formation of these two distinct potential drops. It is also shown that both single and multiple axial potential structures are observed only when both geometric and magnetic expansions closely coincide with each other. Coexistence of these two expansions at the same location enhances plasma expansion which facilitates deviation from Boltzmann distribution and violates quasi-neutrality locally.

Localization of Stable and Chaotic Nonpropagating Structures in Nonlinear Mesoscopic Lattices.

NASA Astrophysics Data System (ADS)

Greenfield, Alan Barry

Recent developments in the study of non-linear localized states, especially non-propagating ones, are outlined. Theoretical models of linear and nonlinear states in a lattice of coupled pendulums and related systems are reviewed. Particular attention is paid to those states which can be described by the Nonlinear Schrodinger equation as well as states where two modes can coexist and states exhibiting chaos. Measurement of localized stable and chaotic states in a 35 site physical pendulum lattice is reported. Various measurement techniques that were used are explained. States that were measured include the tanh profile or kink soliton, and the corresponding uniform state in the wavelength 2 mode, a similar soliton and uniform state in the wavelength 4 mode, a domain wall between the wavelength 2 and 4 modes and a domain wall between a chaotic state and the wavelength 2 mode. Amplitude profiles were measured for the stable kink and domain wall states and smooth curves were obtained by dividing the kink states by the corresponding uniform states. Return maps were measured for two sites in the chaotic domain wall. Simulation of a chaotic domain wall in a 50 site numerical lattice is reported. This system has the advantage that its parameters can be modified much more easily than those of the physical lattice. An attempt is made at quantifying the level of chaos as a function of lattice site with fractal dimension calculations on return maps embedded in a three dimensional space. The drive plane of the chaotic domain wall is mapped out in the drive amplitude - drive frequency plane. Transitions to various stable and quasiperiodic domain walls are noted.

Testing the quality of images for permanent magnet desktop MRI systems using specially designed phantoms.

PubMed

Qiu, Jianfeng; Wang, Guozhu; Min, Jiao; Wang, Xiaoyan; Wang, Pengcheng

2013-12-21

Our aim was to measure the performance of desktop magnetic resonance imaging (MRI) systems using specially designed phantoms, by testing imaging parameters and analysing the imaging quality. We designed multifunction phantoms with diameters of 18 and 60 mm for desktop MRI scanners in accordance with the American Association of Physicists in Medicine (AAPM) report no. 28. We scanned the phantoms with three permanent magnet 0.5 T desktop MRI systems, measured the MRI image parameters, and analysed imaging quality by comparing the data with the AAPM criteria and Chinese national standards. Image parameters included: resonance frequency, high contrast spatial resolution, low contrast object detectability, slice thickness, geometrical distortion, signal-to-noise ratio (SNR), and image uniformity. The image parameters of three desktop MRI machines could be measured using our specially designed phantoms, and most parameters were in line with MRI quality control criterion, including: resonance frequency, high contrast spatial resolution, low contrast object detectability, slice thickness, geometrical distortion, image uniformity and slice position accuracy. However, SNR was significantly lower than in some references. The imaging test and quality control are necessary for desktop MRI systems, and should be performed with the applicable phantom and corresponding standards.

Uniform Effects?: Schools Cite Benefits of Student Uniforms, but Researchers See Little Evidence of Effectiveness

ERIC Educational Resources Information Center

Viadero, Debra

2005-01-01

This article reports on the effectiveness of school uniform policies. At Stephen Decatur Middle School, it is the school's policy that all students wear the standard school attire consisting of khaki pants with polo shirts in white, burgundy, or navy blue. Some of the shirts also sport an embroidered Decatur eagle, an optional embellishment.…

25 CFR 900.67 - Will there be a uniform data set for all IHS programs?

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false Will there be a uniform data set for all IHS programs... EDUCATION ASSISTANCE ACT Programmatic Reports and Data Requirements § 900.67 Will there be a uniform data set for all IHS programs? IHS will work with Indian tribe or tribal organization representatives to...

25 CFR 900.67 - Will there be a uniform data set for all IHS programs?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Will there be a uniform data set for all IHS programs... EDUCATION ASSISTANCE ACT Programmatic Reports and Data Requirements § 900.67 Will there be a uniform data set for all IHS programs? IHS will work with Indian tribe or tribal organization representatives to...

25 CFR 900.67 - Will there be a uniform data set for all IHS programs?

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 2 2011-04-01 2011-04-01 false Will there be a uniform data set for all IHS programs... EDUCATION ASSISTANCE ACT Programmatic Reports and Data Requirements § 900.67 Will there be a uniform data set for all IHS programs? IHS will work with Indian tribe or tribal organization representatives to...

25 CFR 900.67 - Will there be a uniform data set for all IHS programs?

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 2 2012-04-01 2012-04-01 false Will there be a uniform data set for all IHS programs... EDUCATION ASSISTANCE ACT Programmatic Reports and Data Requirements § 900.67 Will there be a uniform data set for all IHS programs? IHS will work with Indian tribe or tribal organization representatives to...

25 CFR 900.67 - Will there be a uniform data set for all IHS programs?

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false Will there be a uniform data set for all IHS programs... EDUCATION ASSISTANCE ACT Programmatic Reports and Data Requirements § 900.67 Will there be a uniform data set for all IHS programs? IHS will work with Indian tribe or tribal organization representatives to...

Stand development 18 years after gap creation in a uniform Douglas-fir plantation

Treesearch

Robert O. Curtis; Constance A. Harrington; Leslie C. Brodie

2017-01-01

This report gives early results, 18 years after treatment and 30 years after planting, from a trial of early thinning and gap creation intended to increase biodiversity in a very uniform extensive Douglas-fir plantation. Gap creation has introduced canopy irregularity and a substantial hemlock component into what was originally a very uniform pure Douglas-fir...

Performance of Implementing Guideline Driven Cervical Cancer Screening Measures in an Inner City Hospital System

PubMed Central

Wieland, Daryl L.; Reimers, Laura L.; Wu, Eijean; Nathan, Lisa M.; Gruenberg, Tammy; Abadi, Maria; Einstein, Mark H.

2013-01-01

Objective In 2006, the American Society for Colposcopy and Cervical Pathology (ASCCP) updated evidence based guidelines recommending screening intervals for women with abnormal cervical cytology. In our low-income inner city population, we sought to improve performance by uniformly applying the guidelines to all patients. We report the prospective performance of a comprehensive tracking, evidence-based algorithmically driven call-back and appointment scheduling system for cervical cancer screening in a resource-limited inner city population. Materials and Methods Outreach efforts were formalized with algorithm-based protocols for triage to colposcopy, with universal adherence to evidence-based guidelines. During implementation from August 2006 through July 2008, we prospectively tracked performance using the electronic medical record with administrative and pathology reports to determine performance variables such as the total number of Pap tests, colposcopy visits, and the distribution of abnormal cytology and histology results, including all CIN 2,3 diagnoses. Results 86,257 gynecologic visits and 41,527 Pap tests were performed system-wide during this period of widespread and uniform implementation of standard cervical cancer screening guidelines. The number of Pap tests performed per month varied little. The incidence of CIN 1 significantly decreased from 117/171 (68.4%) the first tracked month to 52/95 (54.7%) the last tracked month (p=0.04). The monthly incidence rate of CIN 2,3, including incident cervical cancers did not change. The total number of colposcopy visits declined, resulting in a 50% decrease in costs related to colposcopy services and approximately a 12% decrease in costs related to excisional biopsies. Conclusions Adherence to cervical cancer screening guidelines reduced the number of unnecessary colposcopies without increasing numbers of potentially missed CIN 2,3 lesions, including cervical cancer. Uniform implementation of administrative-based performance initiatives for cervical cancer screening minimizes differences in provider practices and maximizes performance of screening while containing cervical cancer screening costs. PMID:21959573

Nonimaging solar concentrator with uniform irradiance

NASA Astrophysics Data System (ADS)

Winston, Roland; O'Gallagher, Joseph J.; Gee, Randy C.

2004-09-01

We report results of a study our group has undertaken under NREL/DOE auspices to design a solar concentrator with uniform irradiance on a planar target. This attribute is especially important for photovoltaic concentrators.

Are School Uniforms a Good Fit? Results from the ECLS-K and the NELS

ERIC Educational Resources Information Center

Yeung, Ryan

2009-01-01

One of the most common proposals put forth for reform of the American system of education is to require school uniforms. Proponents argue that uniforms can make schools safer and also improve school attendance and increase student achievement. Opponents contend that uniforms have not been proven to work and may be an infringement on the freedom of…

Symptoms related to new flight attendant uniforms.

PubMed

McNeely, Eileen; Staffa, Steven J; Mordukhovich, Irina; Coull, Brent

2018-01-03

Flight attendants at Alaska Airlines reported health symptoms after the introduction of new uniforms in 2011. The airline replaced the uniforms in 2014 without acknowledging harm. To understand possible uniform-related health effects, we analyzed self-reported health symptoms in crew who participated in the Harvard Flight Attendant Health Study between 2007 and 2015, the period before, during, and after the introduction of new uniforms. We calculated a standardized prevalence of respiratory, dermatological and allergic symptoms at baseline, as well as during and after uniform changes in 684 flight attendants with a varying number of surveys completed across each time point. We used Generalized Estimating Equations (GEE) to model the association between symptoms at baseline versus the exposure period after adjusting for age, gender and smoking status and weighting respondents for the likelihood of attrition over the course of the study period. We found the following symptom prevalence (per 100) increased after the introduction of new uniforms: multiple chemical sensitivity (10 vs 5), itchy/irritated skin (25 vs 13), rash/hives (23 vs 13), itchy eyes (24 vs 14), blurred vision (14 vs 6), sinus congestion (28 vs 24), ear pain (15 vs 12), sore throat (9 vs 5), cough (17 vs 7), hoarseness/loss of voice (12 vs 3), and shortness of breath (8 vs 3). The odds of several symptoms significantly increased compared to baseline after adjusting for potential confounders. This study found a relationship between health complaints and the introduction of new uniforms in this longitudinal occupational cohort.

49 CFR Appendix B to Part 26 - Uniform Report of DBE Awards or Commitments and Payments Form

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 1 2011-10-01 2011-10-01 false Uniform Report of DBE Awards or Commitments and Payments Form B Appendix B to Part 26 Transportation Office of the Secretary of Transportation PARTICIPATION BY DISADVANTAGED BUSINESS ENTERPRISES IN DEPARTMENT OF TRANSPORTATION FINANCIAL ASSISTANCE PROGRAMS Pt. 26, App. B Appendix B to Part 26...

49 CFR Appendix B to Part 26 - Uniform Report of DBE Awards or Commitments and Payments Form

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Uniform Report of DBE Awards or Commitments and Payments Form B Appendix B to Part 26 Transportation Office of the Secretary of Transportation PARTICIPATION BY DISADVANTAGED BUSINESS ENTERPRISES IN DEPARTMENT OF TRANSPORTATION FINANCIAL ASSISTANCE PROGRAMS Pt. 26, App. B Appendix B to Part 26...

A method for real time detecting of non-uniform magnetic field

NASA Astrophysics Data System (ADS)

Marusenkov, Andriy

2015-04-01

The principle of measuring magnetic signatures for observing diverse objects is widely used in Near Surface work (unexploded ordnance (UXO); engineering & environmental; archaeology) and security and vehicle detection systems as well. As a rule, the magnitude of the signals to be measured is much lower than that of the quasi-uniform Earth magnetic field. Usually magnetometers for these purposes contain two or more spatially separated sensors to estimate the full tensor gradient of the magnetic field or, more frequently, only partial gradient components. The both types (scalar and vector) of magnetic sensors could be used. The identity of the scale factors and proper alignment of the sensitivity axes of the vector sensors are very important for deep suppression of the ambient field and detection of weak target signals. As a rule, the periodical calibration procedure is used to keep matching sensors' parameters as close as possible. In the present report we propose the technique for detection magnetic anomalies, which is almost insensitive to imperfect matching of the sensors. This method based on the idea that the difference signals between two sensors are considerably different when the instrument is rotated or moved in uniform and non-uniform fields. Due to the misfit of calibration parameters the difference signal observed at the rotation in the uniform field is similar to the total signal - the sum of the signals of both sensors. Zero change of the difference and total signals is expected, if the instrument moves in the uniform field along a straight line. In contrast, the same move in the non-uniform field produces some response of each of the sensors. In case one measures dB/dx and moves along x direction, the sensors signals is shifted in time with the lag proportional to the distance between sensors and the speed of move. It means that the difference signal looks like derivative of the total signal at move in the non-uniform field. So, using quite simple electronic schematic it is possible to detect the lag between the total and difference signals and to trigger alarms, when the instrument passes near a magnetized object. The proposed method was successfully applied in the two instruments: the low-power search coil magnetometer for vehicle detection system and the low-noise flux-gate magnetometer for magnetocardiograph. Author believes that this approach could be also useful for the fast inspection of the area during the engineering, archaeology, UXO surveys.

A description of QUALCOMM Automatic Satellite Position Reporting (QASPR(R)) for mobile communications

NASA Technical Reports Server (NTRS)

Ames, William G.

1990-01-01

Two satellite position reporting has been introduced into the OmniTRACS mobile satellite communication system. This system significantly improves position reporting reliability and accuracy while simplifying the terminal's hardware. The positioning technique uses the original OmniTRACS TDMA timing signal formats in the forward and return link directions plus an auxiliary, low power forward link signal through a second satellite to derive distance values. The distances are then converted into the mobile terminal's latitude and longitude in real time. A minor augmentation of the spread spectrum profile of the return link allowed the resolution of periodic ambiguities. The system also locates the two satellites in real time with fixed platforms in known locations using identical mobile terminal hardware. Initial accuracies of 1/4 mile have been realized uniformly throughout the USA using a satellite separation of 22 degrees and there are no dead zones, skywaves, or cycle slips as found in terrestrial systems like LORAN-C.

A description of QUALCOMM Automatic Satellite Position Reporting (QASPR(R)) for mobile communications

NASA Astrophysics Data System (ADS)

Ames, William G.

Two satellite position reporting has been introduced into the OmniTRACS mobile satellite communication system. This system significantly improves position reporting reliability and accuracy while simplifying the terminal's hardware. The positioning technique uses the original OmniTRACS TDMA timing signal formats in the forward and return link directions plus an auxiliary, low power forward link signal through a second satellite to derive distance values. The distances are then converted into the mobile terminal's latitude and longitude in real time. A minor augmentation of the spread spectrum profile of the return link allowed the resolution of periodic ambiguities. The system also locates the two satellites in real time with fixed platforms in known locations using identical mobile terminal hardware. Initial accuracies of 1/4 mile have been realized uniformly throughout the USA using a satellite separation of 22 degrees and there are no dead zones, skywaves, or cycle slips as found in terrestrial systems like LORAN-C.

Uniform Ration Cost System - Summary Report

DTIC Science & Technology

1975-06-01

Sliced BEEF, Boneless, Grill Steak Pot Roasts Ground frz Patties HAM, Smoked, Boneless PORK, Roast , Boned PORK, Slices, Boned CHICKEN , RTC...This approach uses the basic preference data (hedonic values) for individual recipes (e.g., glazed carrots) but introduces one modifying factor to...reflect the fact that preference for a recipe is a function of time since its last serving and another factor to reflect the relative weights of meal

The U.S. Response to NEOS: Avoiding a Black Swan Event

DTIC Science & Technology

2016-09-01

Ibid. 224 Rich, “Major Earthquake Scenario.” 44 number of different radio frequencies .225 Employing a uniform system increases communications ...officials from using the radio as a means of communicating important information to tsunami victims. Overall, Japan’s strategy for applying the lessons...MONITORING AGENCY NAME(S) AND ADDRESS(ES) N/A 10. SPONSORING / MONITORING AGENCY REPORT NUMBER 11 . SUPPLEMENTARY NOTES The views expressed in this

Trans World Tidal Gravity Profile.

DTIC Science & Technology

1976-12-01

LABORATORY AIR FORCE SYSTEMS COMMAN D __ UNITEI) STATES AIR FO RC E HANSCOIVI AFB , MASSACHUSETTS 0173 1 ‘ S ~~~~~ V — (~~~) REPORT DOCUMENTATION PAGE...the fundamental station established at Canberra. Uniformity is maintained with the Brussels fundamental station. It is assessed that the...as well as Canberra and Alice Springs still operatin ~; in 1976. Four new stations are described here Kuala Lumpur (~ a1a’~sja) The gravimeter

Theoretical study of the tunnel-boundary lift interference due to slotted walls in the presence of the trailing-vortex system of a lifting model

NASA Technical Reports Server (NTRS)

Matthews, Clarence W

1955-01-01

The equations presented in this report give the interference on the trailing-vortex system of a uniformly loaded finite-span wing in a circular tunnel containing partly open and partly closed walls, with special reference to symmetrical arrangements of the open and closed portions. Methods are given for extending the equations to include tunnel shapes other than circular. The rectangular tunnel is used to demonstrate these methods. The equations are also extended to nonuniformly loaded wings.

Fertigation uniformity under sprinkler irrigation: evaluation and analysis

USDA-ARS?s Scientific Manuscript database

n modern farming systems, fertigation is widely practiced as a cost effective and convenient method for applying soluble fertilizers to crops. Along with efficiency and adequacy, uniformity is an important fertigation performance evaluation criterion. Fertigation uniformity is defined here as a comp...

Assessment of Stone Complexity for PCNL: A Systematic Review of the Literature, How Best Can We Record Stone Complexity in PCNL?

PubMed

Withington, John; Armitage, James; Finch, William; Wiseman, Oliver; Glass, Jonathan; Burgess, Neil

2016-01-01

This study aims to systematically review the literature reporting tools for scoring stone complexity and the stratification of outcomes by stone complexity. In doing so, we aim to determine whether the evidence favors uniform adoption of any one scoring system. PubMed and Embase databases were systematically searched for relevant studies from 2004 to 2014. Reports selected according to predetermined inclusion and exclusion criteria were appraised in terms of methodologic quality and their findings summarized in structured tables. After review, 15 studies were considered suitable for inclusion. Four distinct scoring systems were identified and a further five studies that aimed to validate aspects of those scoring systems. Six studies reported the stratification of outcomes by stone complexity, without specifically defining a scoring system. All studies reported some correlation between stone complexity and stone clearance. Correlation with complications was less clearly established, where investigated. This review does not allow us to firmly recommend one scoring system over the other. However, the quality of evidence supporting validation of the Guy's Stone Score is marginally superior, according to the criteria applied in this study. Further evaluation of the interobserver reliability of this scoring system is required.

Luminaire layout: Design and implementation

NASA Technical Reports Server (NTRS)

Both, A. J.

1994-01-01

The information contained in this report was presented during the discussion regarding guidelines for PAR uniformity in greenhouses. The data shows a lighting uniformity analysis in a research greenhouse for rose production at the Cornell University campus. The luminaire layout was designed using the computer program Lumen-Micro. After implementation of the design, accurate measurements were taken in the greenhouse and the uniformity analysis for both the design and implementation were compared. A study of several supplemental lighting installations resulted in the following recommendations: include only the actual growing area in the lighting uniformity analysis; for growing areas up to 20 square meters, take four measurements per square meter; for growing areas above 20 square meters, take one measurement per square meter; use one of the uniformity criteria and frequency graphs to compare lighting uniformity amongst designs; and design for uniformity criterion of a least 0.75 and the fraction within +/- 15% of the average PAR value should be close to one.

7 CFR 1776.2 - Uniform Federal Assistance Provisions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Uniform Federal Assistance Provisions. 1776.2 Section 1776.2 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) HOUSEHOLD WATER WELL SYSTEM GRANT PROGRAM General § 1776.2 Uniform...

7 CFR 1776.2 - Uniform Federal Assistance Provisions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 12 2011-01-01 2011-01-01 false Uniform Federal Assistance Provisions. 1776.2 Section 1776.2 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) HOUSEHOLD WATER WELL SYSTEM GRANT PROGRAM General § 1776.2 Uniform...

7 CFR 1776.2 - Uniform Federal Assistance Provisions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 12 2013-01-01 2013-01-01 false Uniform Federal Assistance Provisions. 1776.2 Section 1776.2 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) HOUSEHOLD WATER WELL SYSTEM GRANT PROGRAM General § 1776.2 Uniform...

7 CFR 1776.2 - Uniform Federal Assistance Provisions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 12 2014-01-01 2013-01-01 true Uniform Federal Assistance Provisions. 1776.2 Section 1776.2 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) HOUSEHOLD WATER WELL SYSTEM GRANT PROGRAM General § 1776.2 Uniform...

7 CFR 1776.2 - Uniform Federal Assistance Provisions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 12 2012-01-01 2012-01-01 false Uniform Federal Assistance Provisions. 1776.2 Section 1776.2 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) HOUSEHOLD WATER WELL SYSTEM GRANT PROGRAM General § 1776.2 Uniform...

Analysis of condition for uniform lighting generated by array of light emitting diodes with large view angle.

PubMed

Qin, Zong; Wang, Kai; Chen, Fei; Luo, Xiaobing; Liu, Sheng

2010-08-02

In this research, the condition for uniform lighting generated by array of LEDs with large view angle was studied. The luminous intensity distribution of LED is not monotone decreasing with view angle. A LED with freeform lens was designed as an example for analysis. In a system based on LEDs designed in house with a thickness of 20mm and rectangular arrangement, the condition for uniform lighting was derived and the analytical results demonstrated that the uniformity was not decreasing monotonously with the increasing of LED-to-LED spacing. The illuminance uniformities were calculated with Monte Carlo ray tracing simulations and the uniformity was found to increase with the increasing of certain LED-to-LED spacings anomalously. Another type of large view angle LED and different arrangements were discussed in addition. Both analysis and simulation results showed that the method is available for LED array lighting system design on the basis of large view angle LED..

78 FR 72146 - Motor Carrier Management Information System (MCMIS) Changes to Improve Uniformity in the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-02

...-0457] Motor Carrier Management Information System (MCMIS) Changes to Improve Uniformity in the... Management Information System (MCMIS) to allow the Agency to upload the results of associated adjudicated... information concerning a citation associated with a violation that was dismissed or resulted in a finding of...

Discrepancies between Ideal Characteristics of a Property Tax System and Current Practice in New York.

ERIC Educational Resources Information Center

Netzer, Dick; Berne, Robert

1995-01-01

Ideally, voters' and state legislatures' policy choices should underlie a property tax system that is straightforward, comprehensible, systematic, and reasonably related to policy objectives. Administration should be uniform and fair. New York State's property tax system lacks a uniform valuation standard and "circuit breaker" and has…

76 FR 19307 - Privacy Act of 1974; Amendment of Privacy Act System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... accordance with the Privacy Act of 1974, as amended, the U.S. Department of Agriculture (USDA) is amending an existing Forest Service Privacy Act system of records, USDA/FS-3, Uniform Allowance System. DATES: Comments must be received in writing, on or before May 9, 2011. The System of Records USDA/FS-3 Uniform...

Advanced concepts in biomass production and pretreatment. Annual report, April 1986-March 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hiler, E.A.; Miller, F.R.; Dominy, R.E.

1987-04-01

The objective of the research is to develop an integrated system for methane production utilizing terrestrial biomass as the feedstock. The report provides specifics of research activities in the Texas A and M biomass program sponsored by Gas Research Institute and co-funded by Texas Agricultural Experiment Station. Researchers in the program include plant geneticists, plant physiologists, chemists, agronomists, ruminant physiologists, agricultural engineers, biochemical engineers, and agricultural economists. Major research emphases are genetic manipulation, physiology and production systems, harvesting, storage, processing and conversion systems, inhibitors, and economic and system analyses. During the past year, increasing emphasis was placed on the biologicalmore » pretreatment aspects of the program because of the critical importance of the area to the improved efficiency of the overall system. In the breeding, tissue culture, and production programs, continued substantial progress was made in identifying and characterizing sorghums that will produce high biomass yields and have improved lodging resistance and high uniformity. Economic and systems analyses provided important information regarding optimal overall systems.« less

Milestone-specific, Observed data points for evaluating levels of performance (MODEL) assessment strategy for anesthesiology residency programs.

PubMed

Nagy, Christopher J; Fitzgerald, Brian M; Kraus, Gregory P

2014-01-01

Anesthesiology residency programs will be expected to have Milestones-based evaluation systems in place by July 2014 as part of the Next Accreditation System. The San Antonio Uniformed Services Health Education Consortium (SAUSHEC) anesthesiology residency program developed and implemented a Milestones-based feedback and evaluation system a year ahead of schedule. It has been named the Milestone-specific, Observed Data points for Evaluating Levels of performance (MODEL) assessment strategy. The "MODEL Menu" and the "MODEL Blueprint" are tools that other anesthesiology residency programs can use in developing their own Milestones-based feedback and evaluation systems prior to ACGME-required implementation. Data from our early experience with the streamlined MODEL blueprint assessment strategy showed substantially improved faculty compliance with reporting requirements. The MODEL assessment strategy provides programs with a workable assessment method for residents, and important Milestones data points to programs for ACGME reporting.

The Federal Voting Assistance Program: Refocusing and Reorganizing for the Road Ahead

DTIC Science & Technology

2015-12-16

Assistance Program (FVAP) admin-isters the Uniformed and Overseas Citizens Absentee Voting Act (UOCAVA)1 and helps uniformed-service members and other U.S...more effectively within the system. FVAP Assistance Options for Uniformed and Overseas Citizens Absentee Voting Act Voters Assistance seeker

75 FR 28240 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-20

... for the Uniformed Services University of the Health Sciences; and E.O. 9397 (SSN), as amended... Associate Dean for Recruitment and Admissions, Uniformed Services University of the Health Sciences, 4301...: Associate Dean for Recruitment and Admissions, Uniformed Services University of the Health Sciences, 4301...

47 CFR 32.3 - Authority.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Authority. 32.3 Section 32.3 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.3 Authority. This Uniform System of Accounts has been prepared under the...

47 CFR 32.1 - Background.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Background. 32.1 Section 32.1 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.1 Background. The revised Uniform System of Accounts (USOA) is a historical...

47 CFR 32.3 - Authority.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Authority. 32.3 Section 32.3 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.3 Authority. This Uniform System of Accounts has been prepared under the...

47 CFR 32.3 - Authority.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Authority. 32.3 Section 32.3 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.3 Authority. This Uniform System of Accounts has been prepared under the...

47 CFR 32.1 - Background.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Background. 32.1 Section 32.1 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.1 Background. The revised Uniform System of Accounts (USOA) is a historical...

47 CFR 32.1 - Background.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Background. 32.1 Section 32.1 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Preface § 32.1 Background. The revised Uniform System of Accounts (USOA) is a historical...

SIMULATION AND VISUALIZATION OF FLOW PATTERN IN MICROARRAYS FOR LIQUID PHASE OLIGONUCLEOTIDE AND PEPTIDE SYNTHESIS

PubMed Central

O-Charoen, Sirimon; Srivannavit, Onnop; Gulari, Erdogan

2008-01-01

Microfluidic microarrays have been developed for economical and rapid parallel synthesis of oligonucleotide and peptide libraries. For a synthesis system to be reproducible and uniform, it is crucial to have a uniform reagent delivery throughout the system. Computational fluid dynamics (CFD) is used to model and simulate the microfluidic microarrays to study geometrical effects on flow patterns. By proper design geometry, flow uniformity could be obtained in every microreactor in the microarrays. PMID:17480053

The Uniformed and Overseas Citizens Absentee Voting Act: Overview and Issues

DTIC Science & Technology

2009-05-29

action officers to perform voting assistance duties; establish procedures to ensure a postmark or proof of mailing date on absentee ballots; requires...CRS Report for Congress Prepared for Members and Committees of Congress The Uniformed and Overseas Citizens Absentee Voting Act...TYPE 3. DATES COVERED 00-00-2009 to 00-00-2009 4. TITLE AND SUBTITLE The Uniformed and Overseas Citizens Absentee Voting Act: Overview and

Improving global CD uniformity by optimizing post-exposure bake and develop sequences

NASA Astrophysics Data System (ADS)

Osborne, Stephen P.; Mueller, Mark; Lem, Homer; Reyland, David; Baik, KiHo

2003-12-01

Improvements in the final uniformity of masks can be shrouded by error contributions from many sources. The final Global CD Uniformity (GCDU) of a mask is degraded by individual contributions of the writing tool, the Post Applied Bake (PAB), the Post Exposure Bake (PEB), the Develop sequence and the Etch step. Final global uniformity will improve by isolating and minimizing the variability of the PEB and Develop. We achieved this de-coupling of the PEB and Develop process from the whole process stream by using "dark loss" which is the loss of unexposed resist during the develop process. We confirmed a correspondence between Angstroms of dark loss and nanometer sized deviations in the chrome CD. A plate with a distinctive dark loss pattern was related to a nearly identical pattern in the chrome CD. This pattern was verified to have originated during the PEB process and displayed a [Δ(Final CD)/Δ(Dark Loss)] ratio of 6 for TOK REAP200 resist. Previous papers have reported a sensitive linkage between Angstroms of dark loss and nanometers in the final uniformity of the written plate. These initial studies reported using this method to improve the PAB of resists for greater uniformity of sensitivity and contrast. Similarly, this paper demonstrates an outstanding optimization of PEB and Develop processes.

Investigation of non-uniform radiation damage observed in the ZEUS Beam Pipe Calorimeter at HERA

NASA Astrophysics Data System (ADS)

Bohnet, I.; Fricke, U.; Surrow, B.; Wick, K.

1999-08-01

The ZEUS Beam Pipe Calorimeter (BPC) is a small tungsten/scintillator sampling calorimeter. It is positioned at a distance of approximately 4 cm from the HERA beams and approximately 3 m from the interaction point. The accumulated doses measured at the front side of the BPC during the HERA runs 1995, 1996 and 1997 were 12 kGy, 11 kGy and 2.5 kGy, respectively. The radiation dose influenced the optical components of the BPC. The degradation of some of the scintillators due to radiation damage has been examined using different monitoring systems. A simulation code was developed which describes quantitatively the effects of non-uniform radiation damage. The following report describes the radiation monitoring, the effects on the scintillator material and the impact on the energy linearity of the BPC.

Implied dynamics biases the visual perception of velocity.

PubMed

La Scaleia, Barbara; Zago, Myrka; Moscatelli, Alessandro; Lacquaniti, Francesco; Viviani, Paolo

2014-01-01

We expand the anecdotic report by Johansson that back-and-forth linear harmonic motions appear uniform. Six experiments explore the role of shape and spatial orientation of the trajectory of a point-light target in the perceptual judgment of uniform motion. In Experiment 1, the target oscillated back-and-forth along a circular arc around an invisible pivot. The imaginary segment from the pivot to the midpoint of the trajectory could be oriented vertically downward (consistent with an upright pendulum), horizontally leftward, or vertically upward (upside-down). In Experiments 2 to 5, the target moved uni-directionally. The effect of suppressing the alternation of movement directions was tested with curvilinear (Experiment 2 and 3) or rectilinear (Experiment 4 and 5) paths. Experiment 6 replicated the upright condition of Experiment 1, but participants were asked to hold the gaze on a fixation point. When some features of the trajectory evoked the motion of either a simple pendulum or a mass-spring system, observers identified as uniform the kinematic profiles close to harmonic motion. The bias towards harmonic motion was most consistent in the upright orientation of Experiment 1 and 6. The bias disappeared when the stimuli were incompatible with both pendulum and mass-spring models (Experiments 3 to 5). The results are compatible with the hypothesis that the perception of dynamic stimuli is biased by the laws of motion obeyed by natural events, so that only natural motions appear uniform.

Preparation & characterization of high purity Cu2 ZnSn(SxSe1-x)4 nanoparticles

NASA Astrophysics Data System (ADS)

Negash, Bethlehem G.

Research in thin film solar cells applies novel techniques to synthesize cost effective and highly efficient absorber materials in order to generate electricity directly from solar energy. Of these materials, copper zinc tin sulfoselenide (Cu2ZnSn(SxSe1-x) 4) nanoparticles have shown great promise in solar cell applications due to optimal material properties as well as low cost & relative abundance of materials.1,2 Sulfoselenide nanoparticles have also a broader impact in other industries including electronics3, LED 4, and biomedical research5. Of the many routes of manufacturing these class of semiconductors, colloidal synthesis of Cu 2ZnSn(SxSe1-x)4 offers a scalable, low cost and high-throughput route for manufacturing high efficiency thin-film solar cells. Hydrazine processed Cu2ZnSn(SxSe1-x )4 devices have reached a record power conversion efficiency (PCE) of 12.6%, much higher than the 9.6% reported for physical vapor deposition (PVD) systems.6,7. Despite high efficiencies, wet synthesis of nanoparticles, however, is made more complicated in multi-element, quaternary and quinary systems such as copper zinc tin sulfoselenide (CZTSSe) and copper indium gallium diselenide (CIGSe). One major disadvantage in these systems is growth of the desired quaternary or quinary phase in competition with unwanted binary and ternary phases with low energy of formation.8,9 Moreover, various reaction parameters such as reaction time, temperature, and choice of ligand also affect, chemical as well as physical properties of resulting nanoparticles. Understanding of the formation mechanisms of the particles is necessary in order to address some of these challenges in wet synthesis of CZTSSe nanoparticles. In this study, we investigate synthesis conditions & reaction parameters which yield high purity Cu2ZnSn(SxSe1-x) 4 nanoparticles as well as attempt to understand the growth mechanism of these nanoparticles. This was achieved by manipulating anion precursor preparation routes as well order in which precursors are introduced into a reaction system. We report a new solution based sulfoselenide preparation route which has been used to synthesize high purity Cu2ZnSn(S xSe1-x)4 nanoparticles. Uniform phase Cu 2ZnSn(SxSe1-x)4 nanoparticles were successfully synthesized over a wide range of varying chalcogen ratios. It was found that anion precursor solution plays a key role in determining the morphology & phase purity of the final nanoparticles, as observed from X-ray Diffraction (XRD) and Raman spectroscopy. A uniform sulfoselenide solution is needed to produce high purity Cu2ZnSn(SxSe1-x )4 nanoparticles with narrow phase distribution. Moreover, the relative reactivity of each anion must be balanced in order to yield uniform phase nanoparticles. The findings of this study as well as the reported mixed chalcogen precursor preparation route can be applied in various industries, including photovoltaics to produce uniform phase, solution processed sulfoselenide nanoparticles.

Revisiting the Issues: The Uniform Adoption Act.

ERIC Educational Resources Information Center

Hollinger, Joan Heifetz

1995-01-01

Discusses how a complex regulatory system, along with a lack of consensus about the functions served by adoption, produces uncertainty on many basic issues, including distinguishing lawful adoption versus illegal "baby-selling." The author recommends passage of more uniform state adoption laws, describes the 1994 Uniform Adoption Act,…

Gray-level transformations for interactive image enhancement. M.S. Thesis. Final Technical Report

NASA Technical Reports Server (NTRS)

Fittes, B. A.

1975-01-01

A gray-level transformation method suitable for interactive image enhancement was presented. It is shown that the well-known histogram equalization approach is a special case of this method. A technique for improving the uniformity of a histogram is also developed. Experimental results which illustrate the capabilities of both algorithms are described. Two proposals for implementing gray-level transformations in a real-time interactive image enhancement system are also presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conover, David R.

This report acquaints stakeholders and interested parties involved in the development and/or deployment of energy storage systems (ESS) with the subject of safety-related codes, standards and regulations (CSRs). It is hoped that users of this document gain a more in depth and uniform understanding of safety-related CSR development and deployment that can foster improved communications among all ESS stakeholders and the collaboration needed to realize more timely acceptance and approval of safe ESS technology through appropriate CSR.

States to Face Uniform Rules on Grad Data: Spellings to Propose Formula; Extent of Mandates Unclear

ERIC Educational Resources Information Center

Hoff, David J.

2008-01-01

This article reports on plans by the Bush administration to set a uniform way for states to calculate and report their graduation rates, which could make it harder for high schools to avoid accountability measures under the No Child Left Behind Act. In the U.S. Department of Education's latest move to refine the implementation of the NCLB law,…

Prototype development and demonstration for response, emergency staging, communications, uniform management, and evacuation (R.E.S.C.U.M.E.) : technical report on prototype development and field testing of R.E.S.C.U.M.E. applications.

DOT National Transportation Integrated Search

2015-04-01

This document is the final project technical report for the development and field testing of the Response, Emergency Staging, Communications, Uniform Management, and Evacuation (R.E.S.C.U.M.E.) application bundle, with a focus on the Incident Zone (I...

A comparison of foveated acquisition and tracking performance relative to uniform resolution approaches

NASA Astrophysics Data System (ADS)

Dubuque, Shaun; Coffman, Thayne; McCarley, Paul; Bovik, A. C.; Thomas, C. William

2009-05-01

Foveated imaging has been explored for compression and tele-presence, but gaps exist in the study of foveated imaging applied to acquisition and tracking systems. Results are presented from two sets of experiments comparing simple foveated and uniform resolution targeting (acquisition and tracking) algorithms. The first experiments measure acquisition performance when locating Gabor wavelet targets in noise, with fovea placement driven by a mutual information measure. The foveated approach is shown to have lower detection delay than a notional uniform resolution approach when using video that consumes equivalent bandwidth. The second experiments compare the accuracy of target position estimates from foveated and uniform resolution tracking algorithms. A technique is developed to select foveation parameters that minimize error in Kalman filter state estimates. Foveated tracking is shown to consistently outperform uniform resolution tracking on an abstract multiple target task when using video that consumes equivalent bandwidth. Performance is also compared to uniform resolution processing without bandwidth limitations. In both experiments, superior performance is achieved at a given bandwidth by foveated processing because limited resources are allocated intelligently to maximize operational performance. These findings indicate the potential for operational performance improvements over uniform resolution systems in both acquisition and tracking tasks.

Influence of signal intensity non-uniformity on brain volumetry using an atlas-based method.

PubMed

Goto, Masami; Abe, Osamu; Miyati, Tosiaki; Kabasawa, Hiroyuki; Takao, Hidemasa; Hayashi, Naoto; Kurosu, Tomomi; Iwatsubo, Takeshi; Yamashita, Fumio; Matsuda, Hiroshi; Mori, Harushi; Kunimatsu, Akira; Aoki, Shigeki; Ino, Kenji; Yano, Keiichi; Ohtomo, Kuni

2012-01-01

Many studies have reported pre-processing effects for brain volumetry; however, no study has investigated whether non-parametric non-uniform intensity normalization (N3) correction processing results in reduced system dependency when using an atlas-based method. To address this shortcoming, the present study assessed whether N3 correction processing provides reduced system dependency in atlas-based volumetry. Contiguous sagittal T1-weighted images of the brain were obtained from 21 healthy participants, by using five magnetic resonance protocols. After image preprocessing using the Statistical Parametric Mapping 5 software, we measured the structural volume of the segmented images with the WFU-PickAtlas software. We applied six different bias-correction levels (Regularization 10, Regularization 0.0001, Regularization 0, Regularization 10 with N3, Regularization 0.0001 with N3, and Regularization 0 with N3) to each set of images. The structural volume change ratio (%) was defined as the change ratio (%) = (100 × [measured volume - mean volume of five magnetic resonance protocols] / mean volume of five magnetic resonance protocols) for each bias-correction level. A low change ratio was synonymous with lower system dependency. The results showed that the images with the N3 correction had a lower change ratio compared with those without the N3 correction. The present study is the first atlas-based volumetry study to show that the precision of atlas-based volumetry improves when using N3-corrected images. Therefore, correction for signal intensity non-uniformity is strongly advised for multi-scanner or multi-site imaging trials.

Influence of Signal Intensity Non-Uniformity on Brain Volumetry Using an Atlas-Based Method

PubMed Central

Abe, Osamu; Miyati, Tosiaki; Kabasawa, Hiroyuki; Takao, Hidemasa; Hayashi, Naoto; Kurosu, Tomomi; Iwatsubo, Takeshi; Yamashita, Fumio; Matsuda, Hiroshi; Mori, Harushi; Kunimatsu, Akira; Aoki, Shigeki; Ino, Kenji; Yano, Keiichi; Ohtomo, Kuni

2012-01-01

Objective Many studies have reported pre-processing effects for brain volumetry; however, no study has investigated whether non-parametric non-uniform intensity normalization (N3) correction processing results in reduced system dependency when using an atlas-based method. To address this shortcoming, the present study assessed whether N3 correction processing provides reduced system dependency in atlas-based volumetry. Materials and Methods Contiguous sagittal T1-weighted images of the brain were obtained from 21 healthy participants, by using five magnetic resonance protocols. After image preprocessing using the Statistical Parametric Mapping 5 software, we measured the structural volume of the segmented images with the WFU-PickAtlas software. We applied six different bias-correction levels (Regularization 10, Regularization 0.0001, Regularization 0, Regularization 10 with N3, Regularization 0.0001 with N3, and Regularization 0 with N3) to each set of images. The structural volume change ratio (%) was defined as the change ratio (%) = (100 × [measured volume - mean volume of five magnetic resonance protocols] / mean volume of five magnetic resonance protocols) for each bias-correction level. Results A low change ratio was synonymous with lower system dependency. The results showed that the images with the N3 correction had a lower change ratio compared with those without the N3 correction. Conclusion The present study is the first atlas-based volumetry study to show that the precision of atlas-based volumetry improves when using N3-corrected images. Therefore, correction for signal intensity non-uniformity is strongly advised for multi-scanner or multi-site imaging trials. PMID:22778560

Analysis of light emitting diode array lighting system based on human vision: normal and abnormal uniformity condition.

PubMed

Qin, Zong; Ji, Chuangang; Wang, Kai; Liu, Sheng

2012-10-08

In this paper, condition for uniform lighting generated by light emitting diode (LED) array was systematically studied. To take human vision effect into consideration, contrast sensitivity function (CSF) was novelly adopted as critical criterion for uniform lighting instead of conventionally used Sparrow's Criterion (SC). Through CSF method, design parameters including system thickness, LED pitch, LED's spatial radiation distribution and viewing condition can be analytically combined. In a specific LED array lighting system (LALS) with foursquare LED arrangement, different types of LEDs (Lambertian and Batwing type) and given viewing condition, optimum system thicknesses and LED pitches were calculated and compared with those got through SC method. Results show that CSF method can achieve more appropriate optimum parameters than SC method. Additionally, an abnormal phenomenon that uniformity varies with structural parameters non-monotonically in LALS with non-Lambertian LEDs was found and analyzed. Based on the analysis, a design method of LALS that can bring about better practicability, lower cost and more attractive appearance was summarized.

An efficient shutter-less non-uniformity correction method for infrared focal plane arrays

NASA Astrophysics Data System (ADS)

Huang, Xiyan; Sui, Xiubao; Zhao, Yao

2017-02-01

The non-uniformity response in infrared focal plane array (IRFPA) detectors has a bad effect on images with fixed pattern noise. At present, it is common to use shutter to prevent from radiation of target and to update the parameters of non-uniformity correction in the infrared imaging system. The use of shutter causes "freezing" image. And inevitably, there exists the problems of the instability and reliability of system, power consumption, and concealment of infrared detection. In this paper, we present an efficient shutter-less non-uniformity correction (NUC) method for infrared focal plane arrays. The infrared imaging system can use the data gaining in thermostat to calculate the incident infrared radiation by shell real-timely. And the primary output of detector except the shell radiation can be corrected by the gain coefficient. This method has been tested in real infrared imaging system, reaching high correction level, reducing fixed pattern noise, adapting wide temperature range.

Simple estimation of induced electric fields in nervous system tissues for human exposure to non-uniform electric fields at power frequency

NASA Astrophysics Data System (ADS)

Tarao, Hiroo; Miyamoto, Hironobu; Korpinen, Leena; Hayashi, Noriyuki; Isaka, Katsuo

2016-06-01

Most results regarding induced current in the human body related to electric field dosimetry have been calculated under uniform field conditions. We have found in previous work that a contact current is a more suitable way to evaluate induced electric fields, even in the case of exposure to non-uniform fields. If the relationship between induced currents and external non-uniform fields can be understood, induced electric fields in nervous system tissues may be able to be estimated from measurements of ambient non-uniform fields. In the present paper, we numerically calculated the induced electric fields and currents in a human model by considering non-uniform fields based on distortion by a cubic conductor under an unperturbed electric field of 1 kV m-1 at 60 Hz. We investigated the relationship between a non-uniform external electric field with no human present and the induced current through the neck, and the relationship between the current through the neck and the induced electric fields in nervous system tissues such as the brain, heart, and spinal cord. The results showed that the current through the neck can be formulated by means of an external electric field at the central position of the human head, and the distance between the conductor and the human model. As expected, there is a strong correlation between the current through the neck and the induced electric fields in the nervous system tissues. The combination of these relationships indicates that induced electric fields in these tissues can be estimated solely by measurements of the external field at a point and the distance from the conductor.

Titanium dioxide nanowire sensor array integration on CMOS platform using deterministic assembly.

PubMed

Gall, Oren Z; Zhong, Xiahua; Schulman, Daniel S; Kang, Myungkoo; Razavieh, Ali; Mayer, Theresa S

2017-06-30

Nanosensor arrays have recently received significant attention due to their utility in a wide range of applications, including gas sensing, fuel cells, internet of things, and portable health monitoring systems. Less attention has been given to the production of sensor platforms in the μW range for ultra-low power applications. Here, we discuss how to scale the nanosensor energy demand by developing a process for integration of nanowire sensing arrays on a monolithic CMOS chip. This work demonstrates an off-chip nanowire fabrication method; subsequently nanowires link to a fused SiO 2 substrate using electric-field assisted directed assembly. The nanowire resistances shown in this work have the highest resistance uniformity reported to date of 18%, which enables a practical roadmap towards the coupling of nanosensors to CMOS circuits and signal processing systems. The article also presents the utility of optimizing annealing conditions of the off-chip metal-oxides prior to CMOS integration to avoid limitations of thermal budget and process incompatibility. In the context of the platform demonstrated here, directed assembly is a powerful tool that can realize highly uniform, cross-reactive arrays of different types of metal-oxide nanosensors suited for gas discrimination and signal processing systems.

Titanium dioxide nanowire sensor array integration on CMOS platform using deterministic assembly

NASA Astrophysics Data System (ADS)

Gall, Oren Z.; Zhong, Xiahua; Schulman, Daniel S.; Kang, Myungkoo; Razavieh, Ali; Mayer, Theresa S.

2017-06-01

Nanosensor arrays have recently received significant attention due to their utility in a wide range of applications, including gas sensing, fuel cells, internet of things, and portable health monitoring systems. Less attention has been given to the production of sensor platforms in the μW range for ultra-low power applications. Here, we discuss how to scale the nanosensor energy demand by developing a process for integration of nanowire sensing arrays on a monolithic CMOS chip. This work demonstrates an off-chip nanowire fabrication method; subsequently nanowires link to a fused SiO2 substrate using electric-field assisted directed assembly. The nanowire resistances shown in this work have the highest resistance uniformity reported to date of 18%, which enables a practical roadmap towards the coupling of nanosensors to CMOS circuits and signal processing systems. The article also presents the utility of optimizing annealing conditions of the off-chip metal-oxides prior to CMOS integration to avoid limitations of thermal budget and process incompatibility. In the context of the platform demonstrated here, directed assembly is a powerful tool that can realize highly uniform, cross-reactive arrays of different types of metal-oxide nanosensors suited for gas discrimination and signal processing systems.

A Site Density Functional Theory for Water: Application to Solvation of Amino Acid Side Chains.

PubMed

Liu, Yu; Zhao, Shuangliang; Wu, Jianzhong

2013-04-09

We report a site density functional theory (SDFT) based on the conventional atomistic models of water and the universality ansatz of the bridge functional. The excess Helmholtz energy functional is formulated in terms of a quadratic expansion with respect to the local density deviation from that of a uniform system and a universal functional for all higher-order terms approximated by that of a reference hard-sphere system. With the atomistic pair direct correlation functions of the uniform system calculated from MD simulation and an analytical expression for the bridge functional from the modified fundamental measure theory, the SDFT can be used to predict the structure and thermodynamic properties of water under inhomogeneous conditions with a computational cost negligible in comparison to that of brute-force simulations. The numerical performance of the SDFT has been demonstrated with the predictions of the solvation free energies of 15 molecular analogs of amino acid side chains in water represented by SPC/E, SPC, and TIP3P models. For theTIP3P model, a comparison of the theoretical predictions with MD simulation and experimental data shows agreement within 0.64 and 1.09 kcal/mol on average, respectively.

Nonequilibrium mode-coupling theory for uniformly sheared underdamped systems.

PubMed

Suzuki, Koshiro; Hayakawa, Hisao

2013-01-01

Nonequilibrium mode-coupling theory (MCT) for uniformly sheared underdamped systems is developed, starting from the microscopic thermostated Sllod equation and the corresponding Liouville equation. Special attention is paid to the translational invariance in the sheared frame, which requires an appropriate definition of the transient time correlators. The derived MCT equation satisfies the alignment of the wave vectors and is manifestly translationally invariant. Isothermal condition is implemented by the introduction of current fluctuation in the dissipative coupling to the thermostat. This current fluctuation grows in the α relaxation regime, which generates a pronounced relaxation of the yield stress compared to the overdamped case. This result fills the gap between the molecular dynamics simulation and the overdamped MCT reported previously. The response to a perturbation of the shear rate demonstrates an inertia effect which is not observed in the overdamped case. Our theory turns out to be a nontrivial extension of the theory by Fuchs and Cates [J. Rheol. 53, 957 (2009)] to underdamped systems. Since our starting point is identical to that of Chong and Kim [Phys. Rev. E 79, 021203 (2009)], the contradictions between Fuchs-Cates and Chong-Kim are resolved.

Uniform and non-uniform modes of nanosecond-pulsed dielectric barrier discharge in atmospheric air: fast imaging and spectroscopic measurements of electric field

PubMed Central

Liu, Chong; Dobrynin, Danil; Fridman, Alexander

2014-01-01

In this study, we report experimental results on fast ICCD imaging of development of nanosecond-pulsed dielectric barrier discharge (DBD) in atmospheric air and spectroscopic measurements of electric field in the discharge. Uniformity of the discharge images obtained with nanosecond exposure times were analyzed using chi-square test. The results indicate that DBD uniformity strongly depends on applied (global) electric field in the discharge gap, and is a threshold phenomenon. We show that in the case of strong overvoltage on the discharge gap (provided by fast rise times), there is transition from filamentary to uniform DBD mode which correlates to the corresponding decrease of maximum local electric field in the discharge. PMID:25071294

Uniform and non-uniform modes of nanosecond-pulsed dielectric barrier discharge in atmospheric air: fast imaging and spectroscopic measurements of electric field.

PubMed

Liu, Chong; Dobrynin, Danil; Fridman, Alexander

2014-06-25

In this study, we report experimental results on fast ICCD imaging of development of nanosecond-pulsed dielectric barrier discharge (DBD) in atmospheric air and spectroscopic measurements of electric field in the discharge. Uniformity of the discharge images obtained with nanosecond exposure times were analyzed using chi-square test. The results indicate that DBD uniformity strongly depends on applied (global) electric field in the discharge gap, and is a threshold phenomenon. We show that in the case of strong overvoltage on the discharge gap (provided by fast rise times), there is transition from filamentary to uniform DBD mode which correlates to the corresponding decrease of maximum local electric field in the discharge.

46 CFR 403.400 - Uniform pilot's source form.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 8 2011-10-01 2011-10-01 false Uniform pilot's source form. 403.400 Section 403.400... ACCOUNTING SYSTEM Source Forms § 403.400 Uniform pilot's source form. (a) Each Association shall record pilotage transactions on a form approved by the Director. The approved form shall be issued to pilots by...

Continuity of pullback and uniform attractors

NASA Astrophysics Data System (ADS)

Hoang, Luan T.; Olson, Eric J.; Robinson, James C.

2018-03-01

We study the continuity of pullback and uniform attractors for non-autonomous dynamical systems with respect to perturbations of a parameter. Consider a family of dynamical systems parameterized by λ ∈ Λ, where Λ is a complete metric space, such that for each λ ∈ Λ there exists a unique pullback attractor Aλ (t). Using the theory of Baire category we show under natural conditions that there exists a residual set Λ* ⊆ Λ such that for every t ∈ R the function λ ↦Aλ (t) is continuous at each λ ∈Λ* with respect to the Hausdorff metric. Similarly, given a family of uniform attractors Aλ, there is a residual set at which the map λ ↦Aλ is continuous. We also introduce notions of equi-attraction suitable for pullback and uniform attractors and then show when Λ is compact that the continuity of pullback attractors and uniform attractors with respect to λ is equivalent to pullback equi-attraction and, respectively, uniform equi-attraction. These abstract results are then illustrated in the context of the Lorenz equations and the two-dimensional Navier-Stokes equations.

A Cost and Performance System (CAPS) in a Federal agency

NASA Technical Reports Server (NTRS)

Huseonia, W. F.; Penton, P. G.

1994-01-01

Cost and Performance System (CAPS) is an automated system used from the planning phase through implementation to analysis and documentation. Data is retrievable or available for analysis of cost versus performance anomalies. CAPS provides a uniform system across intra- and international elements. A common system is recommended throughout an entire cost or profit center. Data can be easily accumulated and aggregated into higher levels of tracking and reporting of cost and performance.The level and quality of performance or productivity is indicated in the CAPS model and its process. The CAPS model provides the necessary decision information and insight to the principal investigator/project engineer for a successful project management experience. CAPS provides all levels of management with the appropriate detailed level of data.

25 CFR 10.6 - How is the BIA assured that the policies and standards are being applied uniformly and facilities...

Code of Federal Regulations, 2010 CFR

2010-04-01

...-mandatory detention standards and will document progress on uniform reporting. The BIA Office of Law... OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAW AND ORDER INDIAN COUNTRY DETENTION FACILITIES AND...

AN AUTOMATED SYSTEM FOR PRODUCING UNIFORM SURFACE DEPOSITS OF DRY PARTICLES

EPA Science Inventory

A laboratory system has been constructed that uniformly deposits dry particles onto any type of test surface. Devised as a quality assurance tool for the purpose of evaluating surface sampling methods for lead, it also may be used to generate test surfaces for any contaminant ...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

What can Europeans learn from Americans?

PubMed Central

Enthoven, Alain C.

1989-01-01

In a wide-ranging look at many aspects of health care financing and delivery, the concepts of glasnost and perestroika are used as a framework for presenting ideas from the American system that may have value for European health care planners. These include more uniform approaches to data collection and cost reporting, patient outcome studies, evaluation of service and access standards, publication of information, quality assurance review, decentralization and independent institutions, prepaid group practice, demonstrations and experiments, and managed competition. Suggestions are offered for making health care systems on both sides of the Atlantic more manageable, efficient, and responsive. PMID:10313435

Cost and quality trends in direct contracting arrangements.

PubMed

Lyles, Alan; Weiner, Jonathan P; Shore, Andrew D; Christianson, Jon; Solberg, Leif I; Drury, Patricia

2002-01-01

This paper presents the first empirical analysis of a 1997 initiative of the Buyers Health Care Action Group (BHCAG) known as Choice Plus. This initiative entailed direct contracts with provider-controlled delivery systems; annual care system bidding; public reports of consumer satisfaction and quality; uniform benefits; and risk-adjusted payment. After case-mix adjustment, hospital costs decreased, ambulatory care costs rose modestly, and pharmacy costs increased substantially. Process-oriented quality indicators were stable or improved. The BHCAG employer-to-provider direct contracting and consumer choice model appeared to perform reasonably well in containing costs, without measurable adverse effects on quality.

Laser Texturing of Magnetic Recording Media Final Report CRADA No. TSV-1298-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hackel, L.; Marshall, A.

The Commercial Laser Systems Group at LLNL developed a concept for patterning of computer magnetic recording discs. Magnetic recording media require texturing over areas designated for contact in order to minimize friction with data transducing heads. In fabricating a hard disk, an aluminum nickel-phosphorous substrate was polished to a specular finish then a mechanical means was used to roughen an annular area intended to be the head contact band. In a previous patent (US Patent 5,062,021) it was proposed that the focused output of a low power laser with short pulse length could be used to generate the textured pattern.more » However, the patterned area typically required 75,000 textured spots that needed to be rapidly (less than 10 seconds) printed with good uniformity. A means to achieve the accurate placement and uniform profile, as well as a meaningfully rapid process time, was not discussed in the referenced patent. The LLNL team devised a system that could rapidly and inexpensively accomplish the texturing.« less

Highly uniform resistive switching properties of amorphous InGaZnO thin films prepared by a low temperature photochemical solution deposition method.

PubMed

Hu, Wei; Zou, Lilan; Chen, Xinman; Qin, Ni; Li, Shuwei; Bao, Dinghua

2014-04-09

We report on highly uniform resistive switching properties of amorphous InGaZnO (a-IGZO) thin films. The thin films were fabricated by a low temperature photochemical solution deposition method, a simple process combining chemical solution deposition and ultraviolet (UV) irradiation treatment. The a-IGZO based resistive switching devices exhibit long retention, good endurance, uniform switching voltages, and stable distribution of low and high resistance states. Electrical conduction mechanisms were also discussed on the basis of the current-voltage characteristics and their temperature dependence. The excellent resistive switching properties can be attributed to the reduction of organic- and hydrogen-based elements and the formation of enhanced metal-oxide bonding and metal-hydroxide bonding networks by hydrogen bonding due to UV irradiation, based on Fourier-transform-infrared spectroscopy, X-ray photoelectron spectroscopy, and Field emission scanning electron microscopy analysis of the thin films. This study suggests that a-IGZO thin films have potential applications in resistive random access memory and the low temperature photochemical solution deposition method can find the opportunity for further achieving system on panel applications if the a-IGZO resistive switching cells were integrated with a-IGZO thin film transistors.

Particle circulation and solids transport in large bubbling fluidized beds. Progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Homsy, G.M.

1982-04-01

We have undertaken a theoretical study of the possibility of the formation of plumes or channeling when coal particles volatilize upon introduction to a fluidized bed, Fitzgerald (1980). We have completed the analysis of the basic state of uniform flow and are currently completing a stability analysis. We have modified the continuum equations of fluidization, Homsy et al. (1980), to include the source of gas due to volatilization, which we assume to be uniformly distributed spatially. Simplifying these equations and solving leads to the prediction of a basic state analogous to the state of uniform fluidization found when no sourcemore » is present within the medium. We are currently completing a stability analysis of this basic state which will give the critical volatilization rate above which the above simple basic state is unstable. Because of the experimental evidence of Jewett and Lawless (1981), who observed regularly spaced plume-like instabilities upon drying a bed of saturated silica gel, we are considering two-dimensional periodic disturbances. The analysis is similar to that given by Homsy, et al. (1980) and Medlin et al. (1974). We hope to determine the stability limits for this system shortly.« less

Redefining Molecular Amphipathicity in Reversing the "Coffee-Ring Effect": Implications for Single Base Mutation Detection.

PubMed

Huang, Chi; Wang, Jie; Lv, Xiaobo; Liu, Liu; Liang, Ling; Hu, Wei; Luo, Changliang; Wang, Fubing; Yuan, Quan

2018-05-21

The "coffee ring effect" is a natural phenomenon where sessile drops leave ring-shaped structures on solid surfaces upon drying. It drives non-uniform deposition of suspended compounds on substrates, which adversely affects many processes, including surface-assisted biosensing and molecular self-assembly. In this study, we describe how the coffee ring effect can be eliminated by controlling the amphipathicity of the suspended compounds, for example DNA modified with hydrophobic dye. Specifically, nuclease digestion of the hydrophilic DNA end converts the dye-labeled molecule into an amphipathic molecule (one with comparably weighted hydrophobic and hydrophilic ends) and reverses the coffee ring effect and results in uniform disc-shaped feature deposition of the dye. The amphipathic product decreases the surface tension of the sessile drops and induces Marangoni flow, which drives the uniform distribution of the amphipathic dye-labeled product in the drops. As proof-of-concept, this strategy was used in a novel enzymatic amplification method for biosensing to eliminate the coffee ring effect on a nitrocellulose membrane and increase assay reliability and sensitivity. Importantly, the reported strategy for eliminating the coffee ring effect can be extended to other sessile drop systems for potentially improving assay reliability, and sensitivity.

Uniform Mass Distribution Properties and Body Size Appropriate for the 50 Percentile Male Aircrewmember during 1980-1990.

DTIC Science & Technology

1981-03-27

a(ireument that differences in recorded data for this size- was . .;mall amongj the various users. An Anthropometry Task group and a Mas...meeting, Dr. K. W. Kennedy of the Anthropometry Tauk group provided a status report on the Air Force proqram to develop appropriate anthropometric and...seating considerations and requirements for the handicapped and elderly . Included in this reference are dimensions for link systems and simple drafting

Calibration of a spatial light modulator containing dual frequency liquid crystal

NASA Astrophysics Data System (ADS)

Gu, Dong-Feng; Winker, Bruce; Wen, Bing; Taber, Don; Brackley, Andrew; Wirth, Allan; Albanese, Marc; Landers, Frank

2005-08-01

Characterization and calibration process for a liquid crystal (LC) spatial light modulator (SLM) containing dual frequency liquid crystal is described. Special care was taken when dealing with LC cell gap non-uniformity and defect pixels. The calibration results were fed into a closed loop control algorithm to demonstrate correction of wavefront distortions. The performance characteristics of the device were reported. Substantial improvements were made in speed (bandwidth), resolution, power consumption and system weight/volume.

Bethesda 2014: improving on a paradigm shift.

PubMed

Wilbur, D C; Nayar, R

2015-12-01

The third iteration of the Bethesda System terminology manual was recently published. This update included changes in the reporting of benign endometrial cells, and guidance for special adequacy situations and for cases in which low grade squamous intraepithelial lesions are accompanied by some cells suggesting that a high grade lesion might also be present. In addition, the manual was increased in size to include more illustrations with special studies and comparisons to histology, a greatly increased reference list, and a new chapter devoted to the modern practice of risk-based management. The third edition of the Bethesda manual is meant to serve as a primary reference for the practice of gynecologic cytology designed to provide a uniform system of reporting Worldwide for clinical, teaching, and research purposes. © 2015 John Wiley & Sons Ltd.

Adhesion of voids to bimetal interfaces with non-uniform energies

DOE PAGES

Zheng, Shijian; Shao, Shuai; Zhang, Jian; ...

2015-10-21

Interface engineering has become an important strategy for designing radiation-resistant materials. Critical to its success is fundamental understanding of the interactions between interfaces and radiation-induced defects, such as voids. Using transmission electron microscopy, here we report an interesting phenomenon in their interaction, wherein voids adhere to only one side of the bimetal interfaces rather than overlapping them. We show that this asymmetrical void-interface interaction is a consequence of differing surface energies of the two metals and non-uniformity in their interface formation energy. Specifically, voids grow within the phase of lower surface energy and wet only the high-interface energy regions. Furthermore,more » because this outcome cannot be accounted for by wetting of interfaces with uniform internal energy, our report provides experimental evidence that bimetal interfaces contain non-uniform internal energy distributions. Ultimately, this work also indicates that to design irradiation-resistant materials, we can avoid void-interface overlap via tuning the configurations of interfaces.« less

Development of high repetition rate nitric oxide planar laser induced fluorescence imaging

NASA Astrophysics Data System (ADS)

Jiang, Naibo

This thesis has documented the development of a MHz repitition rate pulse burst laser system. Second harmonic and third harmonic efficiencies are improved by adding a Phase Conjugate Mirror to the system. Some high energy fundamental, second harmonic, and third harmonic burst sequences consisting of 1--12 pulses separated in time by between 4 and 12 microseconds are now routinely obtained. The reported burst envelopes are quite uniform. We have also demonstrated the ability to generate ultra-high frequency sequences of broadly wavelength tunable, high intensity laser pulses using a home built injection seeded Optical Parametric Oscillator (OPO), pumped by the second and third harmonic output of the pulse burst laser. Typical OPO output burst sequences consist of 6--10 pulses, separated in time by between 6 and 10 microseconds. With third harmonic pumping of the OPO system, we studied four conditions, two-crystal Singly Resonant OPO (SRO) cavity, three-crystal OPO cavity, single pass two-crystal Doubly Resonant OPO (DRO) cavity and double pass two-crystal OPO cavity. The double pass two-crystal OPO cavity gives the best operation in burst mode. For single pass OPO, the average total OPO conversion efficiency is approximately 25%. For double pass OPO, the average total OPO conversion efficiency is approximately 35%. As a preliminary work, we studied 532nm pumping of a single crystal OPO cavity. With single pulse pumping, the conversion efficiency can reach 30%. For both 355nm and 532nm pumping OPO, we have demonstrated injection seeding. The OPO output light linewidth is significantly narrowed. Some preliminary etalon traces are also reported. By mixing the OPO signal output at 622nm with residual third harmonic at 355nm, we obtained 226nm burst sequences with average pulse energy of ˜0.2 mJ. Injection seeding of the OPO increases the energy achieved by a factor of ˜2. 226nm burst sequences with reasonably uniform burst envelopes are reported. Using the system we have obtained, for the first time by any known optical method, Planar Laser Induced Fluorescence (PLIF) image sequences at ultrahigh (≥100kHz) frame rates, in particular NO PLIF image sequences, have been obtained in a Mach 2 jet. We also studied the possibility of utilizing a 250 kHz pulsed Nd:YVO 4 laser as the master oscillator. 10-pulse-10-mus spacing burst sequences with reasonably uniform burst envelope have been obtained. The total energy of the burst sequence is ˜2.5J.

Formation process of graphite film on Ni substrate with improved thickness uniformity through precipitation control

NASA Astrophysics Data System (ADS)

Kim, Seul-Gi; Hu, Qicheng; Nam, Ki-Bong; Kim, Mun Ja; Yoo, Ji-Beom

2018-04-01

Large-scale graphitic thin film with high thickness uniformity needs to be developed for industrial applications. Graphitic films with thicknesses ranging from 3 to 20 nm have rarely been reported, and achieving the thickness uniformity in that range is a challenging task. In this study, a process for growing 20 nm-thick graphite films on Ni with improved thickness uniformity is demonstrated and compared with the conventional growth process. In the film grown by the process, the surface roughness and coverage were improved and no wrinkles were observed. Observations of the film structure reveal the reasons for the improvements and growth mechanisms.

Over 95% of large-scale length uniformity in template-assisted electrodeposited nanowires by subzero-temperature electrodeposition.

PubMed

Shin, Sangwoo; Kong, Bo Hyun; Kim, Beom Seok; Kim, Kyung Min; Cho, Hyung Koun; Cho, Hyung Hee

2011-07-23

In this work, we report highly uniform growth of template-assisted electrodeposited copper nanowires on a large area by lowering the deposition temperature down to subzero centigrade. Even with highly disordered commercial porous anodic aluminum oxide template and conventional potentiostatic electrodeposition, length uniformity over 95% can be achieved when the deposition temperature is lowered down to -2.4°C. Decreased diffusion coefficient and ion concentration gradient due to the lowered deposition temperature effectively reduces ion diffusion rate, thereby favors uniform nanowire growth. Moreover, by varying the deposition temperature, we show that also the pore nucleation and the crystallinity can be controlled.

Electrode structure for uniform corona discharge

NASA Technical Reports Server (NTRS)

Gange, R. A.; Steinmetz, C. C.

1976-01-01

Single corona-discharge needle is used to apply uniform charge to thermoplastic medium in holograph-storage system. Needle is connected to flat transparent electrode that is parallel to thermoplastic.

Multidisciplinary Aerospace Systems Optimization: Computational AeroSciences (CAS) Project

NASA Technical Reports Server (NTRS)

Kodiyalam, S.; Sobieski, Jaroslaw S. (Technical Monitor)

2001-01-01

The report describes a method for performing optimization of a system whose analysis is so expensive that it is impractical to let the optimization code invoke it directly because excessive computational cost and elapsed time might result. In such situation it is imperative to have user control the number of times the analysis is invoked. The reported method achieves that by two techniques in the Design of Experiment category: a uniform dispersal of the trial design points over a n-dimensional hypersphere and a response surface fitting, and the technique of krigging. Analyses of all the trial designs whose number may be set by the user are performed before activation of the optimization code and the results are stored as a data base. That code is then executed and referred to the above data base. Two applications, one of the airborne laser system, and one of an aircraft optimization illustrate the method application.

Bicubic uniform B-spline wavefront fitting technology applied in computer-generated holograms

NASA Astrophysics Data System (ADS)

Cao, Hui; Sun, Jun-qiang; Chen, Guo-jie

2006-02-01

This paper presented a bicubic uniform B-spline wavefront fitting technology to figure out the analytical expression for object wavefront used in Computer-Generated Holograms (CGHs). In many cases, to decrease the difficulty of optical processing, off-axis CGHs rather than complex aspherical surface elements are used in modern advanced military optical systems. In order to design and fabricate off-axis CGH, we have to fit out the analytical expression for object wavefront. Zernike Polynomial is competent for fitting wavefront of centrosymmetric optical systems, but not for axisymmetrical optical systems. Although adopting high-degree polynomials fitting method would achieve higher fitting precision in all fitting nodes, the greatest shortcoming of this method is that any departure from the fitting nodes would result in great fitting error, which is so-called pulsation phenomenon. Furthermore, high-degree polynomials fitting method would increase the calculation time in coding computer-generated hologram and solving basic equation. Basing on the basis function of cubic uniform B-spline and the character mesh of bicubic uniform B-spline wavefront, bicubic uniform B-spline wavefront are described as the product of a series of matrices. Employing standard MATLAB routines, four kinds of different analytical expressions for object wavefront are fitted out by bicubic uniform B-spline as well as high-degree polynomials. Calculation results indicate that, compared with high-degree polynomials, bicubic uniform B-spline is a more competitive method to fit out the analytical expression for object wavefront used in off-axis CGH, for its higher fitting precision and C2 continuity.

Mosquito bite protection of U.S. Army and U.S. Marine Corps fire-resistant uniforms

USDA-ARS?s Scientific Manuscript database

The US Department of Defense system for personal protection of deployed personnel consists of wearing repellent on the skin and a permethrin-treated uniform to cover the rest of the body. Since 1991, treatment of combat uniforms with permethrin has been done primarily in the field using a 2 gallon ...

A solution-processed quaternary oxide system obtained at low-temperature using a vertical diffusion technique

PubMed Central

Yoon, Seokhyun; Kim, Si Joon; Tak, Young Jun; Kim, Hyun Jae

2017-01-01

We report a method for fabricating solution-processed quaternary In-Ga-Zn-O (IGZO) thin-film transistors (TFTs) at low annealing temperatures using a vertical diffusion technique (VDT). The VDT is a deposition process for spin-coating binary and ternary oxide layers consecutively and annealing at once. With the VDT, uniform and dense quaternary oxide layers were fabricated at lower temperatures (280 °C). Compared to conventional IGZO and ternary In-Zn-O (IZO) thin films, VDT IGZO thin film had higher density of the metal-oxide bonds and lower density of the oxygen vacancies. The field-effect mobility of VDT IGZO TFT increased three times with an improved stability under positive bias stress than IZO TFT due to the reduction in oxygen vacancies. Therefore, the VDT process is a simple method that reduces the processing temperature without any additional treatment for quaternary oxide semiconductors with uniform layers. PMID:28230088

A solution-processed quaternary oxide system obtained at low-temperature using a vertical diffusion technique

NASA Astrophysics Data System (ADS)

Yoon, Seokhyun; Kim, Si Joon; Tak, Young Jun; Kim, Hyun Jae

2017-02-01

We report a method for fabricating solution-processed quaternary In-Ga-Zn-O (IGZO) thin-film transistors (TFTs) at low annealing temperatures using a vertical diffusion technique (VDT). The VDT is a deposition process for spin-coating binary and ternary oxide layers consecutively and annealing at once. With the VDT, uniform and dense quaternary oxide layers were fabricated at lower temperatures (280 °C). Compared to conventional IGZO and ternary In-Zn-O (IZO) thin films, VDT IGZO thin film had higher density of the metal-oxide bonds and lower density of the oxygen vacancies. The field-effect mobility of VDT IGZO TFT increased three times with an improved stability under positive bias stress than IZO TFT due to the reduction in oxygen vacancies. Therefore, the VDT process is a simple method that reduces the processing temperature without any additional treatment for quaternary oxide semiconductors with uniform layers.

A wearable multiplexed silicon nonvolatile memory array using nanocrystal charge confinement

PubMed Central

Kim, Jaemin; Son, Donghee; Lee, Mincheol; Song, Changyeong; Song, Jun-Kyul; Koo, Ja Hoon; Lee, Dong Jun; Shim, Hyung Joon; Kim, Ji Hoon; Lee, Minbaek; Hyeon, Taeghwan; Kim, Dae-Hyeong

2016-01-01

Strategies for efficient charge confinement in nanocrystal floating gates to realize high-performance memory devices have been investigated intensively. However, few studies have reported nanoscale experimental validations of charge confinement in closely packed uniform nanocrystals and related device performance characterization. Furthermore, the system-level integration of the resulting devices with wearable silicon electronics has not yet been realized. We introduce a wearable, fully multiplexed silicon nonvolatile memory array with nanocrystal floating gates. The nanocrystal monolayer is assembled over a large area using the Langmuir-Blodgett method. Efficient particle-level charge confinement is verified with the modified atomic force microscopy technique. Uniform nanocrystal charge traps evidently improve the memory window margin and retention performance. Furthermore, the multiplexing of memory devices in conjunction with the amplification of sensor signals based on ultrathin silicon nanomembrane circuits in stretchable layouts enables wearable healthcare applications such as long-term data storage of monitored heart rates. PMID:26763827

A solution-processed quaternary oxide system obtained at low-temperature using a vertical diffusion technique.

PubMed

Yoon, Seokhyun; Kim, Si Joon; Tak, Young Jun; Kim, Hyun Jae

2017-02-23

We report a method for fabricating solution-processed quaternary In-Ga-Zn-O (IGZO) thin-film transistors (TFTs) at low annealing temperatures using a vertical diffusion technique (VDT). The VDT is a deposition process for spin-coating binary and ternary oxide layers consecutively and annealing at once. With the VDT, uniform and dense quaternary oxide layers were fabricated at lower temperatures (280 °C). Compared to conventional IGZO and ternary In-Zn-O (IZO) thin films, VDT IGZO thin film had higher density of the metal-oxide bonds and lower density of the oxygen vacancies. The field-effect mobility of VDT IGZO TFT increased three times with an improved stability under positive bias stress than IZO TFT due to the reduction in oxygen vacancies. Therefore, the VDT process is a simple method that reduces the processing temperature without any additional treatment for quaternary oxide semiconductors with uniform layers.

New Flexible Channels for Room Temperature Tunneling Field Effect Transistors.

PubMed

Hao, Boyi; Asthana, Anjana; Hazaveh, Paniz Khanmohammadi; Bergstrom, Paul L; Banyai, Douglas; Savaikar, Madhusudan A; Jaszczak, John A; Yap, Yoke Khin

2016-02-05

Tunneling field effect transistors (TFETs) have been proposed to overcome the fundamental issues of Si based transistors, such as short channel effect, finite leakage current, and high contact resistance. Unfortunately, most if not all TFETs are operational only at cryogenic temperatures. Here we report that iron (Fe) quantum dots functionalized boron nitride nanotubes (QDs-BNNTs) can be used as the flexible tunneling channels of TFETs at room temperatures. The electrical insulating BNNTs are used as the one-dimensional (1D) substrates to confine the uniform formation of Fe QDs on their surface as the flexible tunneling channel. Consistent semiconductor-like transport behaviors under various bending conditions are detected by scanning tunneling spectroscopy in a transmission electron microscopy system (in-situ STM-TEM). As suggested by computer simulation, the uniform distribution of Fe QDs enable an averaging effect on the possible electron tunneling pathways, which is responsible for the consistent transport properties that are not sensitive to bending.

A wearable multiplexed silicon nonvolatile memory array using nanocrystal charge confinement.

PubMed

Kim, Jaemin; Son, Donghee; Lee, Mincheol; Song, Changyeong; Song, Jun-Kyul; Koo, Ja Hoon; Lee, Dong Jun; Shim, Hyung Joon; Kim, Ji Hoon; Lee, Minbaek; Hyeon, Taeghwan; Kim, Dae-Hyeong

2016-01-01

Strategies for efficient charge confinement in nanocrystal floating gates to realize high-performance memory devices have been investigated intensively. However, few studies have reported nanoscale experimental validations of charge confinement in closely packed uniform nanocrystals and related device performance characterization. Furthermore, the system-level integration of the resulting devices with wearable silicon electronics has not yet been realized. We introduce a wearable, fully multiplexed silicon nonvolatile memory array with nanocrystal floating gates. The nanocrystal monolayer is assembled over a large area using the Langmuir-Blodgett method. Efficient particle-level charge confinement is verified with the modified atomic force microscopy technique. Uniform nanocrystal charge traps evidently improve the memory window margin and retention performance. Furthermore, the multiplexing of memory devices in conjunction with the amplification of sensor signals based on ultrathin silicon nanomembrane circuits in stretchable layouts enables wearable healthcare applications such as long-term data storage of monitored heart rates.

Analytical exploration of a TiO2 nanofluid along a rotating disk with homogeneous-heterogeneous chemical reactions and non-uniform heat source/sink

NASA Astrophysics Data System (ADS)

Das, Kalidas; Chakraborty, Tanmoy; Kumar Kundu, Prabir

2017-12-01

Comparative flow features of two different nanofluids containing TiO2 nanoparticles along a rotating disk near a stagnation point are theoretically addressed here. The primary fluids are presumed as ethylene glycol and water. The influences of non-uniform heat absorption/generation with homogeneous and heterogeneous chemical reactions have been integrated to modify the energy and concentration profiles. By virtue of similarity conversions, the leading partial differential system has been standardized into non-linear ODEs and then cracked analytically by NDM and numerically by RK-4 based shooting practice. Impressions of emerging parameters on the flow regime have been reported by tables and graphs coupled with required discussions. One of our results predicts that, with the augmentation of TiO2 nanoparticles concentration, the rate of heat transport for ethylene glycol nanofluid becomes 30-36% higher compared to that of a water nanofluid.

Multiphysics Model of Palladium Hydride Isotope Exchange Accounting for Higher Dimensionality

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gharagozloo, Patricia E.; Eliassi, Mehdi; Bon, Bradley Luis

2015-03-01

This report summarizes computational model developm ent and simulations results for a series of isotope exchange dynamics experiments i ncluding long and thin isothermal beds similar to the Foltz and Melius beds and a lar ger non-isothermal experiment on the NENG7 test bed. The multiphysics 2D axi-symmetr ic model simulates the temperature and pressure dependent exchange reactio n kinetics, pressure and isotope dependent stoichiometry, heat generation from the r eaction, reacting gas flow through porous media, and non-uniformities in the bed perme ability. The new model is now able to replicate the curved reaction front and asy mmetry of themore » exit gas mass fractions over time. The improved understanding of the exchange process and its dependence on the non-uniform bed properties and te mperatures in these larger systems is critical to the future design of such sy stems.« less

Need for Continuation of the Uniformed Services University of the Health Sciences. Report of the Subcommittee on Investigations of the Committee on Armed Services, House of Representatives, with Dissenting Views. Ninety-Fifth Congress, First Session.

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. House Committee on Armed Services.

The report of the subcommittee favoring continuation of the Uniformed Services University of the Health Sciences consists of four parts: (1) the history of the university, the reasons for its establishment; (2) the findings and conclusions of the subcommittee on the discontinuation of institutional funds; (3) the subcommittee's recommendations for…

Regulation of the Deposition Morphology of Inkjet-Printed Crystalline Materials via Polydopamine Functional Coatings for Highly Uniform and Electrically Conductive Patterns.

PubMed

Liu, Liang; Ma, Siyuan; Pei, Yunheng; Xiong, Xiao; Sivakumar, Preeth; Singler, Timothy J

2016-08-24

We report a method to achieve highly uniform inkjet-printed silver nitrate (AgNO3) and a reactive silver precursor patterns on rigid and flexible substrates functionalized with polydopamine (PDA) coatings. The printed AgNO3 patterns on PDA-coated substrates (glass and polyethylene terephthalate (PET)) exhibit a narrow thickness distribution ranging between 0.9 and 1 μm in the line transverse direction and uniform deposition profiles in the line axial direction. The deposited reactive silver precursor patterns on PDA-functionalized substrates also show "dome-shaped" morphology without "edge-thickened" structure due to "coffee-stain" effect. We posit that the highly uniform functional ink deposits formed on PDA-coated substrates are attributable to the strong binding interaction between the abundant catecholamine moieties at the PDA surface and the metallic silver cations (Ag(+) or Ag(NH3)(2+)) in the solutal inks. During printing of the ink rivulet and solvent evaporation, the substrate-liquid ink (S-L) interface is enriched with the silver-based cations and a solidification at the S/L interface is induced. The preferential solidification initiated at the S-L interface is further verified by the in situ visualization of the dynamic solidification process during solvent evaporation, and results suggest an enhanced crystal nucleation and growth localized at the S-L interface on PDA functionalized substrates. This interfacial interaction mediates solute transport in the liquid phase, resulting in the controlled enrichment of solute at the S-L interface and mitigated solute precipitation in both the contact line region and the liquid ink-vapor (L-V) interface due to evaporation. This mediated transport contributes to the final uniform solid deposition for both types of ink systems. This technique provides a complementary strategy for achieving highly uniform inkjet-printed crystalline structures, and can serve as an innovative foundation for high-precision additive delivery of functional materials.

Characterization and improvement of field CD uniformity for implementation of 0.15-μm technology device using KrF stepper

NASA Astrophysics Data System (ADS)

Hyun, Yoon-Suk; Kim, Dong-Joo; Koh, Cha-Won; Park, Sung-Nam; Kwon, Won-Taik

2003-06-01

xAs the design rule of semiconductor device shrinks, the field CD uniformity gets more important. For mass production of 0.15 μm technology device using KrF stepper having 0.63NA, the improvement of field CD uniformity was one of key issues because field CD uniformity is directly related to device characteristics in some layers. We have experienced steppers that show poor illumination uniformity. With those steppers there was large CD difference of about 10nm between field center and field edges as shown in Figure 1. Although we were using verified reticles, we could not get an acceptable CD uniformity in a field with those steppers. The Field CD uniformity is dominantly dependent of the illumination uniformity of stepper and mask quality. With these optimization, we could control DICD difference between field center and edge to be less than 5nm. In this paper, we characterized the dependency of field CD uniformity according to illumination systems with stepper and scanner, annular illumination uniformity at various stigma, mask CD uniformity and the several types of novel gray filter specifically developed.

75 FR 65357 - Request for Public Comment: 30-Day Proposed Information Collection: Office of Urban Indian Health...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-22

... Collection: Title: Office of Urban Indian Health Programs (OUIHP) Uniform Data System (UDS). Type of... Respondents: Title V urban Indian health programs. The table below provides: Types of data collection... Proposed Information Collection: Office of Urban Indian Health Programs; Uniform Data System AGENCY: Indian...

The Uniform Migrant Student Record Transfer System. A Position Paper.

ERIC Educational Resources Information Center

National Committee on the Education of Migrant Children, New York, NY.

Initiated in the mid-sixties under Title I of the Elementary and Secondary Education Act, the Uniform Migrant Student Record Transfer System (UMSRTS) was designed to maintain ready accessibility via computer data base to the health and academic records of migrant children. The National Committee on the Education of Migrant Children (NCEMC)…

Deadly drop--cholinergic syndrome from wearing a laundered uniform.

PubMed

Senthilkumaran, Subramanian; SathyaPrabhu, Krishnanswamy; Balamurugan, Namasivayam; Thirumalaikolundusubramanian, Ponniah

2012-01-01

Unintentional organophosphate compound poisoning, although known, contamination of organophosphate compound through laundered uniform and subsequent transcutaneous absorption, in 30 children is reported herewith for its rarity. Emergency physicians have to recognize such entities clinically, confirm by laboratory means wherever possible, and intervene with appropriate measures.

7 CFR 3015.83 - Federal cash transactions report.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FINANCIAL OFFICER, DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Financial Reporting..., as appropriate, when reporting is to be accomplished with the assistance of automatic data processing...

An Experimental Study of Ignition Effects and Flame Growth Over a Thin Solid Fuel in Low-Speed Concurrent Flow Using Drop-Tower Facilities

NASA Technical Reports Server (NTRS)

Pettegrew, Richard Dale

1996-01-01

An experimental study of ignition and flame growth over a thin solid fuel in oxidizer flow speeds from 0 to 10 cm/sec concurrent flow was performed. This study examined the differences between ignition using a resistively heated wire (woven in a sawtooth pattern over the leading edge of the fuel), and a straight resistively heated wire augmented by a chemical ignitor doped onto the leading edge of the fuel. Results showed that the chemical system yielded non-uniform ignition bursts, while the system using only the hotwire gave more uniform ignition. At speeds up to 2.5 cm/sec, the chemical system yielded non-uniform pyrolysis fronts, while the hotwire system gave more uniform pyrolysis fronts. At speeds of 5 cm/sec or greater, both systems gave uniform pyrolysis fronts. The chemically-ignited flames tended to become too dim to see faster than the hotwire-ignited flames, and the flame lengths were observed to be shorter (after the initial burst subsided) for the chemical system for all speeds. Flame and pyrolysis element velocities were measured. Temperature profiles for selected tests were measured using thermocouples at the fuel surface and in the gas phase. Comparisons between the flame element velocities and peak temperatures recorded in these tests with calculated spread rates and peak temperatures from a steady-state model are presented. Agreement was found to be within 20% for most flame elements for nominal velocities of 5 cm/sec and 7.5 cm/sec.

The research and development of water resources management information system based on ArcGIS

NASA Astrophysics Data System (ADS)

Cui, Weiqun; Gao, Xiaoli; Li, Yuzhi; Cui, Zhencai

According to that there are large amount of data, complexity of data type and format in the water resources management, we built the water resources calculation model and established the water resources management information system based on the advanced ArcGIS and Visual Studio.NET development platform. The system can integrate the spatial data and attribute data organically, and manage them uniformly. It can analyze spatial data, inquire by map and data bidirectionally, provide various charts and report forms automatically, link multimedia information, manage database etc. . So it can provide spatial and static synthetical information services for study, management and decision of water resources, regional geology and eco-environment etc..

Investigation of phase distribution using Phame® in-die phase measurements

NASA Astrophysics Data System (ADS)

Buttgereit, Ute; Perlitz, Sascha

2009-03-01

As lithography mask processes move toward 45nm and 32nm node, mask complexity increases steadily, mask specifications tighten and process control becomes extremely important. Driven by this fact the requirements for metrology tools increase as well. Efforts in metrology have been focused on accurately measuring CD linearity and uniformity across the mask, and accurately measuring phase variation on Alternating/Attenuated PSM and transmission for Attenuated PSM. CD control on photo masks is usually done through the following processes: exposure dose/focus change, resist develop and dry etch. The key requirement is to maintain correct CD linearity and uniformity across the mask. For PSM specifically, the effect of CD uniformity for both Alternating PSM and Attenuated PSM and etch depth for Alternating PSM becomes also important. So far phase measurement has been limited to either measuring large-feature phase using interferometer-based metrology tools or measuring etch depth using AFM and converting etch depth into phase under the assumption that trench profile and optical properties of the layers remain constant. However recent investigations show that the trench profile and optical property of layers impact the phase. This effect is getting larger for smaller CD's. The currently used phase measurement methods run into limitations because they are not able to capture 3D mask effects, diffraction limitations or polarization effects. The new phase metrology system - Phame(R) developed by Carl Zeiss SMS overcomes those limitations and enables laterally resolved phase measurement in any kind of production feature on the mask. The resolution of the system goes down to 120nm half pitch at mask level. We will report on tool performance data with respect to static and dynamic phase repeatability focusing on Alternating PSM. Furthermore the phase metrology system was used to investigate mask process signatures on Alternating PSM in order to further improve the overall PSM process performance. Especially global loading effects caused by the pattern density and micro loading effects caused by the feature size itself have been evaluated using the capability of measuring phase in the small production features. The results of this study will be reported in this paper.

The Uniform Chart of Accounts and Its Use in Management Control.

DTIC Science & Technology

1982-10-01

accounting reports [Ref. 10: p.45]. Horngren [Ref. 5: p. 162] notes that a common complaint of *, managers is that they are unfairly charged with costs ...aids of amsst 0W somir IM WOR M oo Owp U CA Hospital Management Control Uniform Chart of Accounts Performance Measurement Hospital Cost Accounting ...Output Measurement HCU 30. he.T ACT fCamnnus m .. s ado It 09000*Min d IdWOReeO 661 eammeei ~Full implementation of thc Uniform Chart of Accounts (UCA

Dissemination of compressed satellite imagery within the Navy SPAWAR Central Site Product Display environment

NASA Technical Reports Server (NTRS)

Kiselyov, Oleg; Fisher, Paul

1995-01-01

This paper presents a case study of integration of compression techniques within a satellite image communication component of an actual tactical weather information dissemination system. The paper describes history and requirements of the project, and discusses the information flow, request/reply protocols, error handling, and, especially, system integration issues: specification of compression parameters and the place and time for compressor/decompressor plug-ins. A case for a non-uniform compression of satellite imagery is presented, and its implementation in the current system id demonstrated. The paper gives special attention to challenges of moving the system towards the use of standard, non-proprietary protocols (smtp and http) and new technologies (OpenDoc), and reports the ongoing work in this direction.

Aggregation of Minnesota water-use data and transfer of data to the National Water-Use Data System; Procedures and programs

USGS Publications Warehouse

Trotta, L.C.

1988-01-01

The Minnesota Water-Use Data System stores data on the quantity of withdrawals and discharge in Minnesota. To transfer these data into the U.S. Geological Survey 's National Water-Use Data System properly, certain procedures must be followed. Uniform data categorization and entry allows comparison of water use from State to State. The data in the National Water-Use Data System are aggregated by county and by watershed (hydrologic unit). This report documents the data aggregation and transfer process as developed by the Minnesota Department of Natural Resources, the Minnesota State Planning Agency/Planning Information Center, and the U.S. Geological Survey as part of the National Water-Use Information Program.

Learning to teach secondary mathematics using an online learning system

NASA Astrophysics Data System (ADS)

Cavanagh, Michael; Mitchelmore, Michael

2011-12-01

We report the results of a classroom study of three secondary mathematics teachers who had no prior experience teaching with technology as they began to use an online mathematics learning system in their lessons. We gave the teachers only basic instruction on how to operate the system and then observed them intensively over four school terms as they taught using it. We documented changes in the teachers' Pedagogical Technology Knowledge and subsequently classified their various roles as technology bystanders, adopters, adaptors and innovators. Results show that all teachers made some progress toward using the system in more sophisticated ways, but the improvements were not uniform across the teachers. We suggest possible reasons to explain the variation and discuss some implications for teacher professional development.

System Applies Polymer Powder To Filament Tow

NASA Technical Reports Server (NTRS)

Baucom, Robert M.; Snoha, John J.; Marchello, Joseph M.

1993-01-01

Polymer powder applied uniformly and in continuous manner. Powder-coating system applies dry polymer powder to continuous fiber tow. Unique filament-spreading technique, combined with precise control of tension on fibers in system, ensures uniform application of polymer powder to web of spread filaments. Fiber tows impregnated with dry polymer powders ("towpregs") produced for preform-weaving and composite-material-molding applications. System and process valuable to prepreg industry, for production of flexible filament-windable tows and high-temperature polymer prepregs.

A technique for automatically extracting useful field of view and central field of view images.

PubMed

Pandey, Anil Kumar; Sharma, Param Dev; Aheer, Deepak; Kumar, Jay Prakash; Sharma, Sanjay Kumar; Patel, Chetan; Kumar, Rakesh; Bal, Chandra Sekhar

2016-01-01

It is essential to ensure the uniform response of the single photon emission computed tomography gamma camera system before using it for the clinical studies by exposing it to uniform flood source. Vendor specific acquisition and processing protocol provide for studying flood source images along with the quantitative uniformity parameters such as integral and differential uniformity. However, a significant difficulty is that the time required to acquire a flood source image varies from 10 to 35 min depending both on the activity of Cobalt-57 flood source and the pre specified counts in the vendors protocol (usually 4000K-10,000K counts). In case the acquired total counts are less than the total prespecified counts, and then the vendor's uniformity processing protocol does not precede with the computation of the quantitative uniformity parameters. In this study, we have developed and verified a technique for reading the flood source image, remove unwanted information, and automatically extract and save the useful field of view and central field of view images for the calculation of the uniformity parameters. This was implemented using MATLAB R2013b running on Ubuntu Operating system and was verified by subjecting it to the simulated and real flood sources images. The accuracy of the technique was found to be encouraging, especially in view of practical difficulties with vendor-specific protocols. It may be used as a preprocessing step while calculating uniformity parameters of the gamma camera in lesser time with fewer constraints.

Implied Dynamics Biases the Visual Perception of Velocity

PubMed Central

La Scaleia, Barbara; Zago, Myrka; Moscatelli, Alessandro; Lacquaniti, Francesco; Viviani, Paolo

2014-01-01

We expand the anecdotic report by Johansson that back-and-forth linear harmonic motions appear uniform. Six experiments explore the role of shape and spatial orientation of the trajectory of a point-light target in the perceptual judgment of uniform motion. In Experiment 1, the target oscillated back-and-forth along a circular arc around an invisible pivot. The imaginary segment from the pivot to the midpoint of the trajectory could be oriented vertically downward (consistent with an upright pendulum), horizontally leftward, or vertically upward (upside-down). In Experiments 2 to 5, the target moved uni-directionally. The effect of suppressing the alternation of movement directions was tested with curvilinear (Experiment 2 and 3) or rectilinear (Experiment 4 and 5) paths. Experiment 6 replicated the upright condition of Experiment 1, but participants were asked to hold the gaze on a fixation point. When some features of the trajectory evoked the motion of either a simple pendulum or a mass-spring system, observers identified as uniform the kinematic profiles close to harmonic motion. The bias towards harmonic motion was most consistent in the upright orientation of Experiment 1 and 6. The bias disappeared when the stimuli were incompatible with both pendulum and mass-spring models (Experiments 3 to 5). The results are compatible with the hypothesis that the perception of dynamic stimuli is biased by the laws of motion obeyed by natural events, so that only natural motions appear uniform. PMID:24667578

Langmuir Films of Flexible Polymers Transferred to Aqueous/Liquid Crystal Interfaces Induce Uniform Azimuthal Alignment of the Liquid Crystal

PubMed Central

Kinsinger, Michael I.; Buck, Maren E.; Meli, Maria-Victoria; Abbott, Nicholas L.; Lynn, David M.

2009-01-01

We reported recently that amphiphilic polymers can be assembled at interfaces created between aqueous phases and thermotropic liquid crystals (LCs) in ways that (i) couple the organization of the polymer to the order of the LC and (ii) respond to changes in the properties of aqueous phases that can be characterized as changes in the optical appearance of the LC. This investigation sought to characterize the behavior of aqueous-LC interfaces decorated with uniaxially compressed thin films of polymers transferred by Langmuir-Schaefer (LS) transfer. Here, we report physicochemical characterization of interfaces created between aqueous phases and the thermotropic LC 4-cyano-4’-pentylbiphenyl (5CB) decorated with Langmuir films of a novel amphiphilic polymer (polymer 1), synthesized by the addition of hydrophobic and hydrophilic side chains to poly(2-vinyl-4,4’-dimethylazlactone). Initial characterization of this system resulted in the unexpected observation of uniform azimuthal alignment of 5CB after LS transfer of the polymer films to aqueous-5CB interfaces. This paper describes characterization of Langmuir films of polymer 1 hosted at aqueous-5CB interfaces as well as the results of our investigations into the origins of the uniform ordering of the LC observed upon LS transfer. Our results, when combined, support the conclusion that uniform azimuthal alignment of 5CB is the result of long-range ordering of polymer chains in the Langmuir films (in a preferred direction orthogonal to the direction of compression) that is generated during uniaxial compression of the films prior to LS transfer. Although past studies of Langmuir films of polymers at aqueous-air interfaces have demonstrated that in-plane alignment of polymer backbones can be induced by uniaxial compression, these past reports have generally made use of polymers with rigid backbones. One important outcome of this current study is thus the observation of anisotropy and long-range order in Langmuir films of a novel flexible polymer. A second important outcome is the observation that the existence, extent, and dynamics of this order can be identified and characterized optically by transfer of the Langmuir film to a thin film of LC. Additional characterization of Langmuir films of two other flexible polymers [poly(methyl methacrylate) and poly(vinyl stearate)] using this method also resulted in uniform azimuthal alignment of 5CB, suggesting that the generation of long-range order in uniaxially compressed Langmuir films of polymers may also occur more generally over a broader range of polymers with flexible backbones. PMID:19836025

The physics origin of the hierarchy of bodies in space

NASA Astrophysics Data System (ADS)

Bejan, A.; Wagstaff, R. W.

2016-03-01

Here we show that bodies of the same size suspended uniformly in space constitute a system (a "suspension") in a state of uniform volumetric tension because of mass-to-mass forces of attraction. The system "snaps" hierarchically, and evolves faster to a state of reduced tension when the bodies coalesce spontaneously nonuniformly, i.e., hierarchically, into few large and many small bodies suspended in the same space. Hierarchy, not uniformity, is the design that emerges, and it is in accord with the constructal law. The implications of this principle of physics in natural organization and evolution are discussed.

Hydrostatic bearings for a turbine fluid flow metering device

DOEpatents

Fincke, J.R.

1980-05-02

A rotor assembly fluid metering device has been improved by development of a hydrostatic bearing fluid system which provides bearing fluid at a common pressure to rotor assembly bearing surfaces. The bearing fluid distribution system produces a uniform film of fluid distribution system produces a uniform film of fluid between bearing surfaces and allows rapid replacement of bearing fluid between bearing surfaces, thereby minimizing bearing wear and corrosion.

Student Residence Classification: Revision and Review of Regulations.

ERIC Educational Resources Information Center

Nussbaum, Tom; Close, Catherine

This report proposes regulations for the implementation of California's Uniform Student Residency Act by the state's community colleges. First, background information is provided on three laws: (1) the Uniform Student Residency Act, which establishes rules for use in classifying college students as residents or non-residents; (2) legislation…

Influence of different operating conditions on irrigation uniformity with microperforated tapes

NASA Astrophysics Data System (ADS)

Moreno Pizani, María Alejandra; Jesús Farías Ramírez, Asdrúbal

2013-04-01

Irrigated agriculture is a safe alternative to meet the growing demand for food. Numerous studies show that proper management of localized irrigation can increase crop yields and reduce soil salinization. Therefore, periodic field systems irrigation assessments are needed in order to optimize the use efficiency of irrigation water, as well as, to increase the agricultural area covered by the same amount of water and to reduce the environmental impact. It was assessed the behavior of micro perforated tapes under different operating conditions, crops and regions of Venezuela. Evaluations were made on irrigated areas using Santeno ® Type I tape with the following crops: Banana (Musa sp), lettuce (Lactuca sativa L.), carrot (Daucus carota L) and forage sugar cane (Saccharum officinarum). In the other hand, Santeno ® Type II tape was used with papaya (Carica papaya L.) and melon (Cucumis melo L.) crops (the last crop using inverted irrigation tape). The procedures used for sampling and determining the uniformity indices of the system were performed using a series of adjustments to the methodology proposed by Keller and Karmeli (1975), Deniculi (1980) and De Santa and De Juan (1993), in order to increase the number of observations as a function of irrigation time. The calculated irrigation uniformity indices were as follow: Distribution Coefficient (UD), Uniformity Coefficient (CUC), Coefficient of Variation of Flows (CV) and Statistical Uniformity Coefficient (Us). The indices characterization was made according to Merrian and Keller (1978); Bralts (1986); Pizarro (1990) y ASAE (1996), respectively. The results showed that the irrigation uniformity for the evaluated systems varied from excellent to unacceptable, mainly due to the lack of maintenance and the absent of manometric connectors. Among the findings, it is possible to highlight the need for technical support to farmers, both in the installation, management and maintenance of irrigation systems. In this sense, it is proposed to establish a simple and reliable procedure to evaluate the irrigation uniformity in the field, which should be available for farmers and feasible for researchers.

46 CFR 403.400 - Uniform pilot's source form.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ACCOUNTING SYSTEM Source Forms § 403.400 Uniform pilot's source form. (a) Each Association shall record... billing office for accounting record; (4) Third copy to pilot's own Association for pilot's personal...

Improved Thermal-Vacuum Compatible Flat Plate Radiometric Souce for System-Level Testing of Optical Sensors

NASA Technical Reports Server (NTRS)

Schwarz, Mark A.; Kent, Craig J.; Bousquet, Robert; Brown, Steven W.

2015-01-01

This work describes the development of an improved vacuum compatible flat plate radiometric source used for characterizing and calibrating remote optical sensors, in situ, throughout their testing period. The original flat plate radiometric source was developed for use by the VIIRS instrument during the NPOESS Preparatory Project (NPP). Following this effort, the FPI has had significant upgrades in order to improve both the radiometric throughput and uniformity. Results of the VIIRS testing with the reconfigured FPI are reported and discussed.

The Way the Money Goes: An Investigation of Flows of Funding and Resources for Young Children Affected by HIV/AIDS. Working Papers in Early Childhood Development. Young Children and HIV/AIDS Sub-Series, No. 37

ERIC Educational Resources Information Center

Dunn, Alison

2005-01-01

This paper discusses routes by which HIV/AIDS money is dispersed and received. It notes that capturing accurate data on actual spending patterns of large donors can be difficult, as there is no uniform tracking or reporting system and much HIV/AIDS money is spent under the broader category of sexual and reproductive health. Most of the information…

Spacecraft applications of advanced global positioning system technology

NASA Technical Reports Server (NTRS)

1988-01-01

This is the final report on the Texas Instruments Incorporated (TI) simulations study of Spacecraft Application of Advanced Global Positioning System (GPS) Technology. This work was conducted for the NASA Johnson Space Center (JSC) under contract NAS9-17781. GPS, in addition to its baselined capability as a highly accurate spacecraft navigation system, can provide traffic control, attitude control, structural control, and uniform time base. In Phase 1 of this program, another contractor investigated the potential of GPS in these four areas and compared GPS to other techniques. This contract was for the Phase 2 effort, to study the performance of GPS for these spacecraft applications through computer simulations. TI had previously developed simulation programs for GPS differential navigation and attitude measurement. These programs were adapted for these specific spacecraft applications. In addition, TI has extensive expertise in the design and production of advanced GPS receivers, including space-qualified GPS receivers. We have drawn on this background to augment the simulation results in the system level overview, which is Section 2 of this report.

Over 95% of large-scale length uniformity in template-assisted electrodeposited nanowires by subzero-temperature electrodeposition

PubMed Central

2011-01-01

In this work, we report highly uniform growth of template-assisted electrodeposited copper nanowires on a large area by lowering the deposition temperature down to subzero centigrade. Even with highly disordered commercial porous anodic aluminum oxide template and conventional potentiostatic electrodeposition, length uniformity over 95% can be achieved when the deposition temperature is lowered down to -2.4°C. Decreased diffusion coefficient and ion concentration gradient due to the lowered deposition temperature effectively reduces ion diffusion rate, thereby favors uniform nanowire growth. Moreover, by varying the deposition temperature, we show that also the pore nucleation and the crystallinity can be controlled. PMID:21781335

Compartment Venting Analyses of Ares I First Stage Systems Tunnel

NASA Technical Reports Server (NTRS)

Wang, Qunzhen; Arner, Stephen

2009-01-01

Compartment venting analyses have been performed for the Ares I first stage systems tunnel using both the lumped parameter method and the three-dimensional (31)) transient computational fluid dynamics (CFD) approach. The main objective of venting analyses is to predict the magnitudes of differential pressures across the skin so the integrity of solid walls can be evaluated and properly designed. The lumped parameter method assumes the gas pressure and temperature inside the systems tunnel are spatially uniform, which is questionable since the tunnel is about 1,700 in. long and 4 in. wide. Therefore, 31) transient CFD simulations using the commercial CFD code FLUENT are performed in order to examine the gas pressure and temperature variations inside the tunnel. It was found that the uniform pressure and temperature assumptions inside the systems tunnel are valid during ascent. During reentry, the uniform pressure assumption is also reasonable but the uniform temperature assumption is not valid. Predicted pressure and temperature inside the systems tunnel using CFD are also compared with those from the lumped parameter method using the NASA code CHCHVENT. In general, the average pressure and temperature inside the systems tunnel from CFD are between the burst and crush results from CHCHVENT during both ascent and reentry. The skin differential pressure and pressure inside the systems tunnel relative to freestream pressure from CHCHVENT as well as velocity vectors and streamlines are also discussed in detail.

Optimization, Characterization and Commissioning of a Novel Uniform Scanning Proton Beam Delivery System

NASA Astrophysics Data System (ADS)

Mascia, Anthony Edward

Purpose: To develop and characterize the required detectors for uniform scanning optimization and characterization, and to develop the methodology and assess their efficacy for optimizing, characterizing and commissioning a novel proton beam uniform scanning system. Methods and Materials: The Multi Layer Ion Chamber (MLIC), a 1D array of vented parallel plate ion chambers, was developed in-house for measurement of longitudinal profiles. The Matrixx detector (IBA Dosimetry, Germany) and XOmat V film (Kodak, USA) were characterized for measurement of transverse profiles. The architecture of the uniform scanning system was developed and then optimized and characterized for clinical proton radiotherapy. Results: The MLIC detector significantly increased data collection efficiency without sacrificing data quality. The MLIC was capable of integrating an entire scanned and layer stacked proton field with one measurement, producing results with the equivalent spatial sampling of 1.0mm. The Matrixx detector and modified 1D water phantom jig improved data acquisition efficiency and complemented the film measurements. The proximal, central and distal proton field planes were measured using these methods, yielding better than 3% uniformity. The binary range modulator was programmed, optimized and characterized such that the proton field ranges were separated by approximately 5.0mm modulation width and delivered with an accuracy of 1.0mm in water. Several wobbling magnet scan patterns were evaluated and the raster pattern, spot spacing, scan amplitude and overscan margin were optimized for clinical use. Conclusion: Novel detectors and methods are required for clinically efficient optimization and characterization of proton beam scanning systems. Uniform scanning produces proton beam fields that are suited for clinical proton radiotherapy.

[Progressive damage monitoring of corrugated composite skins by the FBG spectral characteristics].

PubMed

Zhang, Yong; Wang, Bang-Feng; Lu, Ji-Yun; Gu, Li-Li; Su, Yong-Gang

2014-03-01

In the present paper, a method of monitoring progressive damage of composite structures by non-uniform fiber Bragg grating (FBG) reflection spectrum is proposed. Due to the finite element analysis of corrugated composite skins specimens, the failure process under tensile load and corresponding critical failure loads of corrugated composite skin was predicated. Then, the non-uniform reflection spectrum of FBG sensor could be reconstructed and the corresponding relationship between layer failure order sequence of corrugated composite skin and FBG sensor reflection spectrums was acquired. A monitoring system based on FBG non-uniform reflection spectrum, which can be used to monitor progressive damage of corrugated composite skins, was built. The corrugated composite skins were stretched under this FBG non-uniform reflection spectrum monitoring system. The results indicate that real-time spectrums acquired by FBG non-uniform reflection spectrum monitoring system show the same trend with the reconstruction reflection spectrums. The maximum error between the corresponding failure and the predictive value is 8.6%, which proves the feasibility of using FBG sensor to monitor progressive damage of corrugated composite skin. In this method, the real-time changes in the FBG non-uniform reflection spectrum within the scope of failure were acquired through the way of monitoring and predicating, and at the same time, the progressive damage extent and layer failure sequence of corru- gated composite skin was estimated, and without destroying the structure of the specimen, the method is easy and simple to operate. The measurement and transmission section of the system are completely composed of optical fiber, which provides new ideas and experimental reference for the field of dynamic monitoring of smart skin.

Measurement of spatial and temporal variation in volatile hazardous air pollutants in Tacoma, Washington, using a mobile membrane introduction mass spectrometry (MIMS) system.

PubMed

Davey, Nicholas G; Fitzpatrick, Cole T E; Etzkorn, Jacob M; Martinsen, Morten; Crampton, Robert S; Onstad, Gretchen D; Larson, Timothy V; Yost, Michael G; Krogh, Erik T; Gilroy, Michael; Himes, Kathy H; Saganić, Erik T; Simpson, Christopher D; Gill, Christopher G

2014-09-19

The objective of this study was to use membrane introduction mass spectrometry (MIMS), implemented on a mobile platform, in order to provide real-time, fine-scale, temporally and spatially resolved measurements of several hazardous air pollutants. This work is important because there is now substantial evidence that fine-scale spatial and temporal variations of air pollutant concentrations are important determinants of exposure to air pollution and adverse health outcomes. The study took place in Tacoma, WA during periods of impaired air quality in the winter and summer of 2008 and 2009. Levels of fine particles were higher in winter compared to summer, and were spatially uniform across the study area. Concentrations of vapor phase pollutants measured by membrane introduction mass spectrometry (MIMS), notably benzene and toluene, had relatively uniform spatial distributions at night, but exhibited substantial spatial variation during the day-daytime levels were up to 3-fold higher at traffic-impacted locations compared to a reference site. Although no direct side-by-side comparison was made between the MIMS system and traditional fixed site monitors, the MIMS system typically reported higher concentrations of specific VOCs, particularly benzene, ethylbenzene and naphthalene, compared to annual average concentrations obtained from SUMA canisters and gas chromatographic analysis at the fixed sites.

Stabilization of a spatially uniform steady state in two systems exhibiting Turing patterns

NASA Astrophysics Data System (ADS)

Konishi, Keiji; Hara, Naoyuki

2018-05-01

This paper deals with the stabilization of a spatially uniform steady state in two coupled one-dimensional reaction-diffusion systems with Turing instability. This stabilization corresponds to amplitude death that occurs in a coupled system with Turing instability. Stability analysis of the steady state shows that stabilization does not occur if the two reaction-diffusion systems are identical. We derive a sufficient condition for the steady state to be stable for any length of system and any boundary conditions. Our analytical results are supported with numerical examples.

Regenerable Photovoltaic Devices with a Hydrogel-Embedded Microvascular Network

PubMed Central

Koo, Hyung-Jun; Velev, Orlin D.

2013-01-01

Light-driven degradation of photoactive molecules could be one of the major obstacles to stable long term operation of organic dye-based solar light harvesting devices. One solution to this problem may be mimicking the regeneration functionality of a plant leaf. We report an organic dye photovoltaic system that has been endowed with such microfluidic regeneration functionality. A hydrogel medium with embedded channels allows rapid and uniform supply of photoactive reagents by a convection-diffusion mechanism. A washing-activation cycle enables reliable replacement of the organic component in a dye-sensitized photovoltaic system. Repetitive restoration of photovoltaic performance after intensive device degradation is demonstrated. PMID:23912814

Diffuse-Illumination Systems for Growing Plants

NASA Technical Reports Server (NTRS)

May, George; Ryan, Robert

2010-01-01

Agriculture in both terrestrial and space-controlled environments relies heavily on artificial illumination for efficient photosynthesis. Plant-growth illumination systems require high photon flux in the spectral range corresponding with plant photosynthetic active radiation (PAR) (400 700 nm), high spatial uniformity to promote uniform growth, and high energy efficiency to minimize electricity usage. The proposed plant-growth system takes advantage of the highly diffuse reflective surfaces on the interior of a sphere, hemisphere, or other nearly enclosed structure that is coated with highly reflective materials. This type of surface and structure uniformly mixes discrete light sources to produce highly uniform illumination. Multiple reflections from within the domelike structures are exploited to obtain diffuse illumination, which promotes the efficient reuse of photons that have not yet been absorbed by plants. The highly reflective surfaces encourage only the plant tissue (placed inside the sphere or enclosure) to absorb the light. Discrete light sources, such as light emitting diodes (LEDs), are typically used because of their high efficiency, wavelength selection, and electronically dimmable properties. The light sources are arranged to minimize shadowing and to improve uniformity. Different wavelengths of LEDs (typically blue, green, and red) are used for photosynthesis. Wavelengths outside the PAR range can be added for plant diagnostics or for growth regulation

Forced response of mistuned bladed disks

NASA Technical Reports Server (NTRS)

Pierre, Christophe

1994-01-01

Small mistuning can cause large, catastrophic changes in blade vibrational response whereby the amplitudes of vibration of some blades may increase by several hundred percent. This can produce 'rogue' blades and HCF failure. The free and forced responses may be highly sensitive to mistuning, and the tuned system predictions may be qualitatively in error and grossly underestimate blade forced response and overestimate fatigue life. Manufacturing tolerances, material non-uniformities, nonidentical root fixtures, and in-service degradation result in blade-to-blade differences that destroy cyclic symmetry in bladed discs. Therefore, a credible forced response prediction system for turbomachinery vibration must take mistuning into account. This report addresses these problems, states several objectives, and introduces NASA research program thrusts concerning this problem. This report was given during the NASA LeRC Workshop on Forced Response in Turbomachinery in August of 1993.

Green auctions and reduction of information rents in payments for environmental services: an experimental investigation in Sunan County, northwestern China.

PubMed

Deng, Xiaohong; Xu, Zhongmin

2015-01-01

Reducing information rents is an important task for government agencies wishing to purchase maximal environmental services with limited budgets. This paper reports on several green auction options for reducing information rents and improving the performance of the "Grain for Green" Payments for environmental services (PES) program implemented in northwestern China. In r experimental auctions and investigations, door-to-door interviews were conducted and bidding envelopes and survey questionnaires were used to determine the offers and the foregone profits of the participants. Three scenarios are analyzed in this paper: a uniform price auction, a discriminatory price auction, and an opportunity-cost system. The results show that compared to the uniform price auction system, the other auction systems can increase the cost-effectiveness of conservation contracting. Competitive bidding can reveal true opportunity costs and can reduce information rents extracted from the government by farmers using private information. The demographics and average bids of these auction types were also analyzed. "Perfect information" in the opportunity-cost offer system has the best performance but is very hard to implement in reality. The results of this research show that the auction is a valuable tool for purchasing conservation contracts in northwestern China, but that in the future, the performance of these auctions should be studied with relaxed model assumptions.

Green Auctions and Reduction of Information Rents in Payments for Environmental Services: An Experimental Investigation in Sunan County, Northwestern China

PubMed Central

Deng, Xiaohong; Xu, Zhongmin

2015-01-01

Reducing information rents is an important task for government agencies wishing to purchase maximal environmental services with limited budgets. This paper reports on several green auction options for reducing information rents and improving the performance of the “Grain for Green” Payments for environmental services (PES) program implemented in northwestern China. In r experimental auctions and investigations, door-to-door interviews were conducted and bidding envelopes and survey questionnaires were used to determine the offers and the foregone profits of the participants. Three scenarios are analyzed in this paper: a uniform price auction, a discriminatory price auction, and an opportunity-cost system. The results show that compared to the uniform price auction system, the other auction systems can increase the cost-effectiveness of conservation contracting. Competitive bidding can reveal true opportunity costs and can reduce information rents extracted from the government by farmers using private information. The demographics and average bids of these auction types were also analyzed. “Perfect information” in the opportunity-cost offer system has the best performance but is very hard to implement in reality. The results of this research show that the auction is a valuable tool for purchasing conservation contracts in northwestern China, but that in the future, the performance of these auctions should be studied with relaxed model assumptions. PMID:25793263

SU-C-9A-02: Structured Noise Index as An Automated Quality Control for Nuclear Medicine: A Two Year Experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, J; Christianson, O; Samei, E

Purpose: Flood-field uniformity evaluation is an essential element in the assessment of nuclear medicine (NM) gamma cameras. It serves as the central element of the quality control (QC) program, acquired and analyzed on a daily basis prior to clinical imaging. Uniformity images are traditionally analyzed using pixel value-based metrics which often fail to capture subtle structure and patterns caused by changes in gamma camera performance requiring additional visual inspection which is subjective and time demanding. The goal of this project was to develop and implement a robust QC metrology for NM that is effective in identifying non-uniformity issues, reporting issuesmore » in a timely manner for efficient correction prior to clinical involvement, all incorporated into an automated effortless workflow, and to characterize the program over a two year period. Methods: A new quantitative uniformity analysis metric was developed based on 2D noise power spectrum metrology and confirmed based on expert observer visual analysis. The metric, termed Structured Noise Index (SNI) was then integrated into an automated program to analyze, archive, and report on daily NM QC uniformity images. The effectiveness of the program was evaluated over a period of 2 years. Results: The SNI metric successfully identified visually apparent non-uniformities overlooked by the pixel valuebased analysis methods. Implementation of the program has resulted in nonuniformity identification in about 12% of daily flood images. In addition, due to the vigilance of staff response, the percentage of days exceeding trigger value shows a decline over time. Conclusion: The SNI provides a robust quantification of the NM performance of gamma camera uniformity. It operates seamlessly across a fleet of multiple camera models. The automated process provides effective workflow within the NM spectra between physicist, technologist, and clinical engineer. The reliability of this process has made it the preferred platform for NM uniformity analysis.« less

Analyses of the Impact of School Uniforms on Violence in North Carolina Public High Schools

ERIC Educational Resources Information Center

Johnson, Wesley Scott

2010-01-01

This study incorporated a multiple-methods design utilizing both quantitative and qualitative data. The quantitative portion investigated several annual reports distributed by the North Carolina Department of Public Instruction (NCDPI) to explore the impact of school uniform policies on incidents of crime and violence and occurrences of…

Report of the 2008 Uniform Regional Scab Nursery for Spring Wheat Parents

USDA-ARS?s Scientific Manuscript database

The Uniform Regional Scab Nursery for Spring Wheat Parents (URSN) was grown for the 14th year in 2008. Five mist-irrigated locations at Brookings, SD; St. Paul, and Crookston, MN; Langdon, ND; and Glenlea, Manitoba, Canada, were planted. A total of 36 entries were included in the 2008 URSN, includin...

Temporal high-pass non-uniformity correction algorithm based on grayscale mapping and hardware implementation

NASA Astrophysics Data System (ADS)

Jin, Minglei; Jin, Weiqi; Li, Yiyang; Li, Shuo

2015-08-01

In this paper, we propose a novel scene-based non-uniformity correction algorithm for infrared image processing-temporal high-pass non-uniformity correction algorithm based on grayscale mapping (THP and GM). The main sources of non-uniformity are: (1) detector fabrication inaccuracies; (2) non-linearity and variations in the read-out electronics and (3) optical path effects. The non-uniformity will be reduced by non-uniformity correction (NUC) algorithms. The NUC algorithms are often divided into calibration-based non-uniformity correction (CBNUC) algorithms and scene-based non-uniformity correction (SBNUC) algorithms. As non-uniformity drifts temporally, CBNUC algorithms must be repeated by inserting a uniform radiation source which SBNUC algorithms do not need into the view, so the SBNUC algorithm becomes an essential part of infrared imaging system. The SBNUC algorithms' poor robustness often leads two defects: artifacts and over-correction, meanwhile due to complicated calculation process and large storage consumption, hardware implementation of the SBNUC algorithms is difficult, especially in Field Programmable Gate Array (FPGA) platform. The THP and GM algorithm proposed in this paper can eliminate the non-uniformity without causing defects. The hardware implementation of the algorithm only based on FPGA has two advantages: (1) low resources consumption, and (2) small hardware delay: less than 20 lines, it can be transplanted to a variety of infrared detectors equipped with FPGA image processing module, it can reduce the stripe non-uniformity and the ripple non-uniformity.

Optical design of an in vivo laparoscopic lighting system

NASA Astrophysics Data System (ADS)

Liu, Xiaolong; Abdolmalaki, Reza Yazdanpanah; Mancini, Gregory J.; Tan, Jindong

2017-12-01

This paper proposes an in vivo laparoscopic lighting system design to address the illumination issues, namely poor lighting uniformity and low optical efficiency, existing in the state-of-the-art in vivo laparoscopic cameras. The transformable design of the laparoscopic lighting system is capable of carrying purposefully designed freeform optical lenses for achieving lighting performance with high illuminance uniformity and high optical efficiency in a desired target region. To design freeform optical lenses for extended light sources such as LEDs with Lambertian light intensity distributions, we present an effective and complete freeform optical design method. The procedures include (1) ray map computation by numerically solving a standard Monge-Ampere equation; (2) initial freeform optical surface construction by using Snell's law and a lens volume restriction; (3) correction of surface normal vectors due to accumulated errors from the initially constructed surfaces; and (4) feedback modification of the solution to deal with degraded illuminance uniformity caused by the extended sizes of the LEDs. We employed an optical design software package to evaluate the performance of our laparoscopic lighting system design. The simulation results show that our design achieves greater than 95% illuminance uniformity and greater than 89% optical efficiency (considering Fresnel losses) for illuminating the target surgical region.

Loading system mechanism for dielectric elastomer generators with equi-biaxial state of deformation

NASA Astrophysics Data System (ADS)

Fontana, M.; Moretti, G.; Lenzo, B.; Vertechy, R.

2014-03-01

Dielectric Elastomer Generators (DEGs) are devices that employ a cyclically variable membrane capacitor to produce electricity from oscillating sources of mechanical energy. Capacitance variation is obtained thanks to the use of dielectric and conductive layers that can undergo different states of deformation including: uniform or non-uniform and uni- or multi-axial stretching. Among them, uniform equi-biaxial stretching is reputed as being the most effective state of deformation that maximizes the amount of energy that can be extracted in a cycle by a unit volume of Dielectric Elastomer (DE) material. This paper presents a DEG concept, with linear input motion and tunable impedance, that is based on a mechanical loading system for inducing uniform equi-biaxial states of deformation. The presented system employs two circular DE membrane capacitors that are arranged in an agonist-antagonist configuration. An analytical model of the overall system is developed and used to find the optimal design parameters that make it possible to tune the elastic response of the generator over the range of motion of interest. An apparatus is developed for the equi-biaxial testing of DE membranes and used for the experimental verification of the employed numerical models.

Automatic control system for uniformly paving iron ore pellets

NASA Astrophysics Data System (ADS)

Wang, Bowen; Qian, Xiaolong

2014-05-01

In iron and steelmaking industry, iron ore pellet qualities are crucial to end-product properties, manufacturing costs and waste emissions. Uniform pellet pavements on the grate machine are a fundamental prerequisite to ensure even heat-transfer and pellet induration successively influences performance of the following metallurgical processes. This article presents an automatic control system for uniformly paving green pellets on the grate, via a mechanism mainly constituted of a mechanical linkage, a swinging belt, a conveyance belt and a grate. Mechanism analysis illustrates that uniform pellet pavements demand the frontend of the swinging belt oscillate at a constant angular velocity. Subsequently, kinetic models are formulated to relate oscillatory movements of the swinging belt's frontend to rotations of a crank link driven by a motor. On basis of kinetic analysis of the pellet feeding mechanism, a cubic B-spline model is built for numerically computing discrete frequencies to be modulated during a motor rotation. Subsequently, the pellet feeding control system is presented in terms of compositional hardware and software components, and their functional relationships. Finally, pellet feeding experiments are carried out to demonstrate that the control system is effective, reliable and superior to conventional methods.

Impact of uniform electrode current distribution on ETF. [Engineering Test Facility MHD generator

NASA Technical Reports Server (NTRS)

Bents, D. J.

1982-01-01

A basic reason for the complexity and sheer volume of electrode consolidation hardware in the MHD ETF Powertrain system is the channel electrode current distribution, which is non-uniform. If the channel design is altered to provide uniform electrode current distribution, the amount of hardware required decreases considerably, but at the possible expense of degraded channel performance. This paper explains the design impacts on the ETF electrode consolidation network associated with uniform channel electrode current distribution, and presents the alternate consolidation designs which occur. They are compared to the baseline (non-uniform current) design with respect to performance, and hardware requirements. A rational basis is presented for comparing the requirements for the different designs and the savings that result from uniform current distribution. Performance and cost impacts upon the combined cycle plant are discussed.

The Design and Construction of the MICE Spectrometer Solenoids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Bert; Wahrer, Bob; Taylor, Clyde

2008-08-02

The purpose of the MICE spectrometer solenoid is to provide a uniform field for a scintillating fiber tracker. The uniform field is produced by a long center coil and two short end coils. Together, they produce 4T field with a uniformity of better than 1% over a detector region of 1000 mm long and 300 mm in diameter. Throughout most of the detector region, the field uniformity is better than 0.3%. In addition to the uniform field coils, we have two match coils. These two coils can be independently adjusted to match uniform field region to the focusing coil field.more » The coil package length is 2544 mm. We present the spectrometer solenoid cold mass design, the powering and quench protection circuits, and the cryogenic cooling system based on using three cryocoolers with re-condensers.« less

An optical system to transform the output beam of a quantum cascade laser to be uniform

NASA Astrophysics Data System (ADS)

Jacobson, Jordan M.

Quantum cascade lasers (QCLs) are a candidate for calibration sources in space-based remote sensing applications. However, the output beam from a QCL has some characteris- tics that are undesirable in a calibration source. The output beam from a QCL is polarized, both temporally and spatially coherent, and has a non-uniform bivariate Gaussian prole. These characteristics need to be mitigated before QCLs can be used as calibration sources. This study presents the design and implementation of an optical system that manipulates the output beam from a QCL so that it is spatially and angularly uniform with reduced coherence and polarization. (85 pages).

Response to non-uniform salinity in the root zone of the halophyte Atriplex nummularia: growth, photosynthesis, water relations and tissue ion concentrations.

PubMed

Bazihizina, Nadia; Colmer, Timothy D; Barrett-Lennard, Edward G

2009-09-01

Soil salinity is often heterogeneous, yet the physiology of halophytes has typically been studied with uniform salinity treatments. An evaluation was made of the growth, net photosynthesis, water use, water relations and tissue ions in the halophytic shrub Atriplex nummularia in response to non-uniform NaCl concentrations in a split-root system. Atriplex nummularia was grown in a split-root system for 21 d, with either the same or two different NaCl concentrations (ranging from 10 to 670 mm), in aerated nutrient solution bathing each root half. Non-uniform salinity, with high NaCl in one root half (up to 670 mm) and 10 mm in the other half, had no effect on shoot ethanol-insoluble dry mass, net photosynthesis or shoot pre-dawn water potential. In contrast, a modest effect occurred for leaf osmotic potential (up to 30 % more solutes compared with uniform 10 mm NaCl treatment). With non-uniform NaCl concentrations (10/670 mm), 90 % of water was absorbed from the low salinity side, and the reduction in water use from the high salinity side caused whole-plant water use to decrease by about 30 %; there was no compensatory water uptake from the low salinity side. Leaf Na(+) and Cl(-) concentrations were 1.9- to 2.3-fold higher in the uniform 670 mm treatment than in the 10/670 mm treatment, whereas leaf K(+) concentrations were 1.2- to 2.0-fold higher in the non-uniform treatment. Atriplex nummularia with one root half in 10 mm NaCl maintained net photosynthesis, shoot growth and shoot water potential even when the other root half was exposed to 670 mm NaCl, a concentration that inhibits growth by 65 % when uniform in the root zone. Given the likelihood of non-uniform salinity in many field situations, this situation would presumably benefit halophyte growth and physiology in saline environments.

Gravitational Influences on Flame Propagation Through Non-Uniform, Premixed Gas Systems

NASA Technical Reports Server (NTRS)

Miller, Fletcher J.; Easton, John; Marchese, Anthony; Hovermann, Fred

2003-01-01

Flame propagation through non-uniformly premixed (or layered) gases has importance both in useful combustion systems and in unintentional fires. As summarized recently and in previous Microgravity Workshop papers, non-uniform premixed gas combustion receives scant attention compared to the more usual limiting cases of diffusion or uniformly premixed flames, especially regarding the role gravity plays. This paper summarizes our recent findings on gravitational effects on layered combustion along a floor, in which the fuel concentration gradient exists normal to the direction of flame spread. In an effort to understand the mechanism by which the flames spread faster in microgravity (and much faster, in laboratory coordinates, than the laminar burning velocity for uniform mixtures), we have begun making pressure measurements across the spreading flame front that are described here. Earlier researchers, testing in 1g, claimed that hydrostatic pressure differences could account for the rapid spread rates. Additionally, we present the development of a new apparatus to study flame spread in free (i.e., far from walls), non-homogeneous fuel layers formed in a flow tunnel behind an airfoil that has been tested in normal gravity.

Increased drop formation frequency via reduction of surfactant interactions in flow-focusing microfluidic devices.

PubMed

Josephides, Dimitris N; Sajjadi, Shahriar

2015-01-27

Glass capillary based microfluidic devices are able to create extremely uniform droplets, when formed under the dripping regime, at low setup costs due to their ease of manufacture. However, as they are rarely parallelized, simple methods to increase droplet production from a single device are sought. Surfactants used to stabilize drops in such systems often limit the maximum flow rate that highly uniform drops can be produced due to the lowering interfacial tension causing jetting. In this paper we show that by simple design changes we can limit the interactions of surfactants and maximize uniform droplet production. Three flow-focused configurations are explored: a standard glass capillary device (consisting of a single round capillary inserted into a square capillary), a nozzle fed device, and a surfactant shielding device (both consisting of two round capillaries inserted into either end of a square capillary). In principle, the maximum productivity of uniform droplets is achieved if surfactants are not present. It was found that surfactants in the standard device greatly inhibit droplet production by means of interfacial tension lowering and tip-streaming phenomena. In the nozzle fed configuration, surfactant interactions were greatly limited, yielding flow rates comparable to, but lower than, a surfactant-free system. In the surfactant shielding configuration, flow rates were equal to that of a surfactant-free system and could make uniform droplets at rates an order of magnitude above the standard surfactant system.

Application of a novel severity grading system for surgical complications after colorectal resection.

PubMed

Mazeh, Haggi; Samet, Yacov; Abu-Wasel, Bassam; Beglaibter, Nahum; Grinbaum, Ronit; Cohen, Tzeela; Pinto, Meir; Hamburger, Tamar; Freund, Herbert R; Nissan, Aviram

2009-03-01

Uniform and accurate reporting of surgical complications is the basis for quality control. We developed a computerized system for reporting and grading surgical complications in colorectal surgery. This study was conducted to evaluate this computerized reporting system. A retrospective chart review was conducted of all surgical complications in patients who underwent resection of the colon or rectum at our institution between the years 1999 and 2004 (n = 408). All complications were recorded using the computerized reporting system and compared with complications reported in the literature. Elective operations were performed in 75.7% of patients, and 24.3% required emergency operations. Of the 408 patients in the study, 239 (58.6%) had an uneventful recovery without complications. At least 1 complication was recorded in 169 (41.4%) patients. Grades 1 and 2 complications were recorded in 83 (20.3%) and 105 (25.7%) patients, respectively, requiring observation or medical treatment only, and 59 patients (14.5%) had grades 3 to 5 complications. The three leading complications were surgical site infection, intraabdominal abscess, and hemorrhage requiring blood transfusion. The grades 3 to 5 complication rate was within the range described in the literature, and the rate of grades 1 and 2 complications was substantially higher. These grades 1 and 2 complications were associated with a substantially longer hospital stay. This novel complication reporting system was found feasible and proved to have a higher sensitivity for recording minor but meaningful complications that tend to prolong hospital stay.

Hybrid slab-microchannel gel electrophoresis system

DOEpatents

Balch, Joseph W.; Carrano, Anthony V.; Davidson, James C.; Koo, Jackson C.

1998-01-01

A hybrid slab-microchannel gel electrophoresis system. The hybrid system permits the fabrication of isolated microchannels for biomolecule separations without imposing the constraint of a totally sealed system. The hybrid system is reusable and ultimately much simpler and less costly to manufacture than a closed channel plate system. The hybrid system incorporates a microslab portion of the separation medium above the microchannels, thus at least substantially reducing the possibility of non-uniform field distribution and breakdown due to uncontrollable leakage. A microslab of the sieving matrix is built into the system by using plastic spacer materials and is used to uniformly couple the top plate with the bottom microchannel plate.

An assessment of the industrial cogeneration market for parabolic dish systems

NASA Technical Reports Server (NTRS)

Doane, J. W.

1981-01-01

The value analysis technique used is straightforward. Maximum allowable life-cycle system cost for the cogeneration system is determined as the sum of the present value of fuels displaced plus the present value of revenues from exported power. Each conventional fuel displaced is described by a unit cost in the first year, a uniform annual consumption rate, and a uniform annual escalation rate for unit cost. Exported energy flows are treated the same as displaced energy.

Towards uniformly dispersed battery electrode composite materials: Characteristics and performance

DOE PAGES

Yo Han Kwon; Takeuchi, Esther S.; Huie, Matthew M.; ...

2016-01-14

Battery electrodes are complex mesoscale systems comprised of electroactive components, conductive additives, and binders. In this report, methods for processing electrodes with dispersion of the components are described. To investigate the degree of material dispersion, a spin-coating technique was adopted to provide a thin, uniform layer that enabled observation of the morphology. Distinct differences in the distribution profile of the electrode components arising from individual materials physical affinities were readily identified. Hansen solubility parameter (HSP) analysis revealed pertinent surface interactions associated with materials dispersivity. Further studies demonstrated that HSPs can provide an effective strategy to identify surface modification approaches formore » improved dispersions of battery electrode materials. Specifically, introduction of surfactantlike functionality such as oleic acid (OA) capping and P3HT-conjugated polymer wrapping on the surface of nanomaterials significantly enhanced material dispersity over the composite electrode. The approach to the surface treatment on the basis of HSP study can facilitate design of composite electrodes with uniformly dispersed morphology and may contribute to enhancing their electrical and electrochemical behaviors. The conductivity of the composites and their electrochemical performance was also characterized. In conclusion, the study illustrates the importance of considering electronic conductivity, electron transfer, and ion transport in the design of environments incorporating active nanomaterials.« less

Eigenmodes of Ducted Flows With Radially-Dependent Axial and Swirl Velocity Components

NASA Technical Reports Server (NTRS)

Kousen, Kenneth A.

1999-01-01

This report characterizes the sets of small disturbances possible in cylindrical and annular ducts with mean flow whose axial and tangential components vary arbitrarily with radius. The linearized equations of motion are presented and discussed, and then exponential forms for the axial, circumferential, and time dependencies of any unsteady disturbances are assumed. The resultant equations form a generalized eigenvalue problem, the solution of which yields the axial wavenumbers and radial mode shapes of the unsteady disturbances. Two numerical discretizations are applied to the system of equations: (1) a spectral collocation technique based on Chebyshev polynomial expansions on the Gauss-Lobatto points, and (2) second and fourth order finite differences on uniform grids. The discretized equations are solved using a standard eigensystem package employing the QR algorithm. The eigenvalues fall into two primary categories: a discrete set (analogous to the acoustic modes found in uniform mean flows) and a continuous band (analogous to convected disturbances in uniform mean flows) where the phase velocities of the disturbances correspond to the local mean flow velocities. Sample mode shapes and eigensystem distributions are presented for both sheared axial and swirling flows. The physics of swirling flows is examined with reference to hydrodynamic stability and completeness of the eigensystem expansions. The effect of assuming exponential dependence in the axial direction is discussed.

Towards uniformly dispersed battery electrode composite materials: Characteristics and performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yo Han Kwon; Takeuchi, Esther S.; Huie, Matthew M.

Battery electrodes are complex mesoscale systems comprised of electroactive components, conductive additives, and binders. In this report, methods for processing electrodes with dispersion of the components are described. To investigate the degree of material dispersion, a spin-coating technique was adopted to provide a thin, uniform layer that enabled observation of the morphology. Distinct differences in the distribution profile of the electrode components arising from individual materials physical affinities were readily identified. Hansen solubility parameter (HSP) analysis revealed pertinent surface interactions associated with materials dispersivity. Further studies demonstrated that HSPs can provide an effective strategy to identify surface modification approaches formore » improved dispersions of battery electrode materials. Specifically, introduction of surfactantlike functionality such as oleic acid (OA) capping and P3HT-conjugated polymer wrapping on the surface of nanomaterials significantly enhanced material dispersity over the composite electrode. The approach to the surface treatment on the basis of HSP study can facilitate design of composite electrodes with uniformly dispersed morphology and may contribute to enhancing their electrical and electrochemical behaviors. The conductivity of the composites and their electrochemical performance was also characterized. In conclusion, the study illustrates the importance of considering electronic conductivity, electron transfer, and ion transport in the design of environments incorporating active nanomaterials.« less

Assessment of the LV-C2 Stack Sampling Probe Location for Compliance with ANSI/HPS N13.1-1999

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glissmeyer, John A.; Antonio, Ernest J.; Flaherty, Julia E.

2015-09-01

This document reports on a series of tests conducted to assess the proposed air sampling location for the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) C2V (LV-C2) exhaust stack with respect to the applicable criteria regarding the placement of an air sampling probe. Federal regulations require that a sampling probe be located in the exhaust stack according to the criteria established by the American National Standards Institute/Health Physics Society (ANSI/HPS) N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. These criteria address the capability of the sampling probemore » to extract a sample that represents the effluent stream. The tests were conducted on the LV-C2 scale model system. Based on the scale model tests, the location proposed for the air sampling probe in the scale model stack meets the requirements of the ANSI/HPS N13.1-1999 standard for velocity uniformity, flow angle, gas tracer and particle tracer uniformity. Additional velocity uniformity and flow angle tests on the actual stack will be necessary during cold startup to confirm the validity of the scale model results in representing the actual stack.« less

Non-contact finger vein acquisition system using NIR laser

NASA Astrophysics Data System (ADS)

Kim, Jiman; Kong, Hyoun-Joong; Park, Sangyun; Noh, SeungWoo; Lee, Seung-Rae; Kim, Taejeong; Kim, Hee Chan

2009-02-01

Authentication using finger vein pattern has substantial advantage than other biometrics. Because human vein patterns are hidden inside the skin and tissue, it is hard to forge vein structure. But conventional system using NIR LED array has two drawbacks. First, direct contact with LED array raise sanitary problem. Second, because of discreteness of LEDs, non-uniform illumination exists. We propose non-contact finger vein acquisition system using NIR laser and Laser line generator lens. Laser line generator lens makes evenly distributed line laser from focused laser light. Line laser is aimed on the finger longitudinally. NIR camera was used for image acquisition. 200 index finger vein images from 20 candidates are collected. Same finger vein pattern extraction algorithm was used to evaluate two sets of images. Acquired images from proposed non-contact system do not show any non-uniform illumination in contrary with conventional system. Also results of matching are comparable to conventional system. We developed Non-contact finger vein acquisition system. It can prevent potential cross contamination of skin diseases. Also the system can produce uniformly illuminated images unlike conventional system. With the benefit of non-contact, proposed system shows almost equivalent performance compared with conventional system.

An IR Navigation System for Pleural PDT

NASA Astrophysics Data System (ADS)

Zhu, Timothy; Liang, Xing; Kim, Michele; Finlay, Jarod; Dimofte, Andreea; Rodriguez, Carmen; Simone, Charles; Friedberg, Joseph; Cengel, Keith

2015-03-01

Pleural photodynamic therapy (PDT) has been used as an adjuvant treatment with lung-sparing surgical treatment for malignant pleural mesothelioma (MPM). In the current pleural PDT protocol, a moving fiber-based point source is used to deliver the light. The light fluences at multiple locations are monitored by several isotropic detectors placed in the pleural cavity. To improve the delivery of light fluence uniformity, an infrared (IR) navigation system is used to track the motion of the light source in real-time at a rate of 20 - 60 Hz. A treatment planning system uses the laser source positions obtained from the IR camera to calculate light fluence distribution to monitor the light dose uniformity on the surface of the pleural cavity. A novel reconstruction algorithm is used to determine the pleural cavity surface contour. A dual-correction method is used to match the calculated fluences at detector locations to the detector readings. Preliminary data from a phantom shows superior light uniformity using this method. Light fluence uniformity from patient treatments is also shown with and without the correction method.

Rigor Mortis: Statistical thoroughness in reporting and the making of truth.

PubMed

Tal, Aner

2016-02-01

Should a uniform checklist be adopted for methodological and statistical reporting? The current article discusses this notion, with particular attention to the use of old versus new statistics, and a consideration of the arguments brought up by Von Roten. The article argues that an overly exhaustive checklist that is uniformly applied to all submitted papers may be unsuitable for multidisciplinary work, and would further result in undue clutter and potentially distract reviewers from pertinent considerations in their evaluation of research articles. © The Author(s) 2015.

Efficient mixing of the solar nebula from uniform Mo isotopic composition of meteorites.

PubMed

Becker, Harry; Walker, Richard J

2003-09-11

The abundances of elements and their isotopes in our Galaxy show wide variations, reflecting different nucleosynthetic processes in stars and the effects of Galactic evolution. These variations contrast with the uniformity of stable isotope abundances for many elements in the Solar System, which implies that processes efficiently homogenized dust and gas from different stellar sources within the young solar nebula. However, isotopic heterogeneity has been recognized on the subcentimetre scale in primitive meteorites, indicating that these preserve a compositional memory of their stellar sources. Small differences in the abundance of stable molybdenum isotopes in bulk rocks of some primitive and differentiated meteorites, relative to terrestrial Mo, suggest large-scale Mo isotopic heterogeneity between some inner Solar System bodies, which implies physical conditions that did not permit efficient mixing of gas and dust. Here we report Mo isotopic data for bulk samples of primitive and differentiated meteorites that show no resolvable deviations from terrestrial Mo. This suggests efficient mixing of gas and dust in the solar nebula at least to 3 au from the Sun, possibly induced by magnetohydrodynamic instabilities. These mixing processes must have occurred before isotopic fractionation of gas-phase elements and volatility-controlled chemical fractionations were established.

Laser induced fluorescence measurements of ion velocity and temperature of drift turbulence driven sheared plasma flow in a linear helicon plasma device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakraborty Thakur, S.; Fedorczak, N.; Manz, P.

2012-08-15

Using laser induced fluorescence (LIF), radial profiles of azimuthal ion fluid velocity and ion temperature are measured in the controlled shear de-correlation experiment (CSDX) linear helicon plasma device. Ion velocities and temperatures are derived from the measured Doppler broadened velocity distribution functions of argon ions. The LIF system employs a portable, high power (>300 mW), narrowband ({approx}1 MHz) tunable diode laser-based system operating at 668.614 nm. Previous studies in CSDX have shown the existence of a radially sheared azimuthal flow as measured with time delay estimation methods and Mach probes. Here, we report the first LIF measurements of sheared plasmamore » fluid flow in CSDX. Above a critical magnetic field, the ion fluid flow profile evolves from radially uniform to peaked on axis with a distinct reversed flow region at the boundary, indicating the development of a sheared azimuthal flow. Simultaneously, the ion temperature also evolves from a radially uniform profile to a profile with a gradient. Measurements in turbulent and coherent drift wave mode dominated plasmas are compared.« less

Self-reported well-being score modelling and prediction: Proof-of-concept of an approach based on linear dynamic systems.

PubMed

Xinyang Li; Poli, Riccardo; Valenza, Gaetano; Scilingo, Enzo Pasquale; Citi, Luca

2017-07-01

Assessment and recognition of perceived well-being has wide applications in the development of assistive healthcare systems for people with physical and mental disorders. In practical data collection, these systems need to be less intrusive, and respect users' autonomy and willingness as much as possible. As a result, self-reported data are not necessarily available at all times. Conventional classifiers, which usually require feature vectors of a prefixed dimension, are not well suited for this problem. To address the issue of non-uniformly sampled measurements, in this study we propose a method for the modelling and prediction of self-reported well-being scores based on a linear dynamic system. Within the model, we formulate different features as observations, making predictions even in the presence of inconsistent and irregular data. We evaluate the proposed method with synthetic data, as well as real data from two patients diagnosed with cancer. In the latter, self-reported scores from three well-being-related scales were collected over a period of approximately 60 days. Prompted each day, the patients had the choice whether to respond or not. Results show that the proposed model is able to track and predict the patients' perceived well-being dynamics despite the irregularly sampled data.

Social influence in small-world networks

NASA Astrophysics Data System (ADS)

Sun, Kai; Mao, Xiao-Ming; Ouyang, Qi

2002-12-01

We report on our numerical studies of the Axelrod model for social influence in small-world networks. Our simulation results show that the topology of the network has a crucial effect on the evolution of cultures. As the randomness of the network increases, the system undergoes a transition from a highly fragmented phase to a uniform phase. We also find that the power-law distribution at the transition point, reported by Castellano et al, is not a critical phenomenon; it exists not only at the onset of transition but also for almost any control parameters. All these power-law distributions are stable against perturbations. A mean-field theory is developed to explain these phenomena.

Luminescence imaging of water during uniform-field irradiation by spot scanning proton beams

NASA Astrophysics Data System (ADS)

Komori, Masataka; Sekihara, Eri; Yabe, Takuya; Horita, Ryo; Toshito, Toshiyuki; Yamamoto, Seiichi

2018-06-01

Luminescence was found during pencil-beam proton irradiation to water phantom and range could be estimated from the luminescence images. However, it is not yet clear whether the luminescence imaging is applied to the uniform fields made of spot-scanning proton-beam irradiations. For this purpose, imaging was conducted for the uniform fields having spread out Bragg peak (SOBP) made by spot scanning proton beams. We designed six types of the uniform fields with different ranges, SOBP widths and irradiation fields. One of the designed fields was irradiated to water phantom and a cooled charge coupled device camera was used to measure the luminescence image during irradiations. We estimated the ranges, field widths, and luminescence intensities from the luminescence images and compared those with the dose distribution calculated by a treatment planning system. For all types of uniform fields, we could obtain clear images of the luminescence showing the SOBPs. The ranges and field widths evaluated from the luminescence were consistent with those of the dose distribution calculated by a treatment planning system within the differences of  ‑4 mm and  ‑11 mm, respectively. Luminescence intensities were almost proportional to the SOBP widths perpendicular to the beam direction. The luminescence imaging could be applied to uniform fields made of spot scanning proton beam irradiations. Ranges and widths of the uniform fields with SOBP could be estimated from the images. The luminescence imaging is promising for the range and field width estimations in proton therapy.

2003 West Virginia crash data

DOT National Transportation Integrated Search

2003-01-01

This report was prepared by Traffic Engineering : personnel, from the West Virginia Division of Highways. The data contained in this : report is collected from Uniform Traffic Crash Reports submitted by state law : enforcement agencies. These law enf...

2002 West Virginia crash data

DOT National Transportation Integrated Search

2003-01-01

This report was prepared by Traffic Engineering : personnel, from the West Virginia Division of Highways. The data contained in this : report is collected from Uniform Traffic Crash Reports submitted by state law : enforcement agencies. These law enf...

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Procurement and Assistance Data System (PADS) provides a mechanism for collecting, assembling, organizing, and presenting acquisition and assistance data for the Department of Energy (DOE). This handbook and associated documents establish a uniform system to report acquisition/assistance data to PADS for the collection, processing, and dissemination of official statistical data on the Department`s acquisition and assistance actions. The data provides, based on information available at the time of request, a basis for any recurring and special reports to the senior procurement executive, Congress, General Accounting Office (GAO), Federal executive agencies, Office of management and Budget (OMB), and the generalmore » public. It provides information for measuring and assessing the extent to which small business firms and small disadvantages business enterprises are sharing in DOE placement, and for other acquisition and assistance policy and management control purposes. The Handbook for the Preparation of the Individual Procurement Action Report (IPAR) has been designed in two sections; Procurement and Financial Assistance to support the individual forms.« less

Fire investigation

NASA Astrophysics Data System (ADS)

Gomberg, A.

There was considerable progress made on several fronts of fire investigation in the United States in recent years. Progress was made in increasing the quantity of fire investigation and reporting, through efforts to develop the National Fire Incident Reporting System. Improving overall quality of fire investigation is the objective of efforts such as the Fire Investigation Handbook, which was developed and published by the National Bureau of Standards, and the upgrading and expanding of the ""dictionary'' of fire investigation and reporting, the NFPA 901, Uniform Coding for Fire Protection, system. The science of fire investigation as furthered also by new approaches to post fire interviews being developed at the University of Washington, and by in-depth research into factors involved in several large loss fires, including the MGM Grand Hotel in Las Vegas. Finally, the use of special study fire investigations - in-depth investigations concentrating on specific fire problems - is producing new glimpses into the nature of the national fire problem. A brief description of the status of efforts in each of these areas is discussed.

Students' Views Concerning Worldview Presuppositions Underpinning Science: Is the World Really Ordered, Uniform, and Comprehensible?

ERIC Educational Resources Information Center

Hansson, Lena

2014-01-01

That nature and the universe are ordered, uniform, and comprehensible is a starting point in science. However, such worldview presuppositions are often taken for granted, rather than explicitly mentioned, in science and in science class. This article takes a worldview perspective and reports from interviews (N = 26) with upper secondary students…

Report of the 2013 uniform regional scab nursery for spring wheat parents

USDA-ARS?s Scientific Manuscript database

The Uniform Regional Scab Nursery for Spring Wheat Parents (URSN) was grown for the 18th year in 2013. Three locations (Brookings, SD, and St. Paul and Crookston, MN) were planted. A total of 23 entries were included in the 2013 URSN, in addition the resistant checks 2375, BacUp, and ND2710, and the...

Achieving pattern uniformity in plasmonic lithography by spatial frequency selection

NASA Astrophysics Data System (ADS)

Liang, Gaofeng; Chen, Xi; Zhao, Qing; Guo, L. Jay

2018-01-01

The effects of the surface roughness of thin films and defects on photomasks are investigated in two representative plasmonic lithography systems: thin silver film-based superlens and multilayer-based hyperbolic metamaterial (HMM). Superlens can replicate arbitrary patterns because of its broad evanescent wave passband, which also makes it inherently vulnerable to the roughness of the thin film and imperfections of the mask. On the other hand, the HMM system has spatial frequency filtering characteristics and its pattern formation is based on interference, producing uniform and stable periodic patterns. In this work, we show that the HMM system is more immune to such imperfections due to its function of spatial frequency selection. The analyses are further verified by an interference lithography system incorporating the photoresist layer as an optical waveguide to improve the aspect ratio of the pattern. It is concluded that a system capable of spatial frequency selection is a powerful method to produce deep-subwavelength periodic patterns with high degree of uniformity and fidelity.

LANL compact laser pumping simulation. Final task report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, B.S.; White, J.

1987-09-28

Rockwell has been tasked with the objective of both qualitatively and quantitatively defining the performance of LANL Compact Laser coupling systems. The performance criteria of the system will be based upon the magnitude and uniformity of the energy distribution in the laser pumping rod. Once this is understood, it will then be possible to improve the device performance via changes in the system`s component parameters. For this study, the authors have chosen to use the Los Alamos Radiometry Code (LARC), which was previously developed by Rockwell. LARC, as an analysis tool, is well suited for this problem because the codemore » contains the needed photometric calculation capability and easily handles the three-dimensionality of the problem. Also, LARC`s internal graphics can provide very informative visual displays of the optical system.« less

Impact of a counter-rotating planetary rotation system on thin-film thickness and uniformity

DOE PAGES

Oliver, J. B.

2017-06-12

Planetary rotation systems incorporating forward- and counter-rotating planets are used as a means of increasing coating-system capacity for large oblong substrates. Comparisons of planetary motion for the two types of rotating systems are presented based on point tracking for multiple revolutions, as well as comparisons of quantitative thickness and uniformity. Counter-rotation system geometry is shown to result in differences in thin-film thickness relative to standard planetary rotation for precision optical coatings. As a result, this systematic error in thin-film thickness will reduce deposition yields for sensitive coating designs.

Impact of a counter-rotating planetary rotation system on thin-film thickness and uniformity.

PubMed

Oliver, J B

2017-06-20

Planetary rotation systems incorporating forward- and counter-rotating planets are used as a means of increasing coating-system capacity for large oblong substrates. Comparisons of planetary motion for the two types of rotating systems are presented based on point tracking for multiple revolutions as well as comparisons of quantitative thickness and uniformity. Counter-rotation system geometry is shown to result in differences in thin-film thickness relative to standard planetary rotation for precision optical coatings. This systematic error in thin-film thickness will reduce deposition yields for sensitive coating designs.

Phase 2: Array automated assembly task low cost silicon solar array project

NASA Technical Reports Server (NTRS)

Jones, G. T.

1979-01-01

Several microwave systems for use in solar cell fabrication were developed and experimentally tested. The first system used a standing wave rectangular waveguide horn applicator. Satisfactory results were achieved with this system for impedance matching and wafer surface heating uniformity. The second system utilized a resonant TM sub 011 mode cylindrical cavity but could not be employed due to its poor energy coupling efficiency. The third and fourth microwave systems utilized a circular waveguide operating in the TM sub 01 and TM sub 11 but had problems with impedance matching, efficiency, and field uniformity.

Impact of a counter-rotating planetary rotation system on thin-film thickness and uniformity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oliver, J. B.

Planetary rotation systems incorporating forward- and counter-rotating planets are used as a means of increasing coating-system capacity for large oblong substrates. Comparisons of planetary motion for the two types of rotating systems are presented based on point tracking for multiple revolutions, as well as comparisons of quantitative thickness and uniformity. Counter-rotation system geometry is shown to result in differences in thin-film thickness relative to standard planetary rotation for precision optical coatings. As a result, this systematic error in thin-film thickness will reduce deposition yields for sensitive coating designs.

Cooling water distribution system

DOEpatents

Orr, Richard

1994-01-01

A passive containment cooling system for a nuclear reactor containment vessel. Disclosed is a cooling water distribution system for introducing cooling water by gravity uniformly over the outer surface of a steel containment vessel using an interconnected series of radial guide elements, a plurality of circumferential collector elements and collector boxes to collect and feed the cooling water into distribution channels extending along the curved surface of the steel containment vessel. The cooling water is uniformly distributed over the curved surface by a plurality of weirs in the distribution channels.

Documentation and Analysis of Rate Development and Cost Accumulation at Naval Air Rework Facility Norfolk.

DTIC Science & Technology

1985-12-01

DODINST 7220.29-H; Uniform Cost Accounting System; SI Cost Accumula, 4r ?, 𔄃 Ac S TRACT (Continue on reverse if necessary and iaentify by tiock number...actual cost accumulation/Uniform Cost Accounting System (DODINST 7220.29 H, Ref. 1) as used in the Naval Aviation depot level maintenance system to a...Mcepted cost accounting practices as identified in the accounting litera- ture and the Cost Accounting Standards and Regulations. . ,’ The research

REACTOR CONTROL SYSTEM

DOEpatents

MacNeill, J.H.; Estabrook, J.Y.

1960-05-10

A reactor control system including a continuous tape passing through a first coolant passageway, over idler rollers, back through another parallel passageway, and over motor-driven rollers is described. Discrete portions of fuel or poison are carried on two opposed active sections of the tape. Driving the tape in forward or reverse directions causes both active sections to be simultaneously inserted or withdrawn uniformly, tending to maintain a more uniform flux within the reactor. The system is particularly useful in mobile reactors, where reduced inertial resistance to control rod movement is important.

2001 West Virginia crash data

DOT National Transportation Integrated Search

2001-01-01

This report was prepared by Traffic Engineering : personnel, from the West Virginia Division of Highways. The data contained in this : report is collected from Uniform Traffic Crash Reports submitted to the Division of : Motor Vehicles by state law e...

7 CFR 3015.90 - Scope.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.90 Scope. This subpart establishes procedures for monitoring and reporting program performance of... grant and subgrant supported activities. ...

7 CFR 3015.90 - Scope.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.90 Scope. This subpart establishes procedures for monitoring and reporting program performance of... grant and subgrant supported activities. ...

7 CFR 3015.90 - Scope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.90 Scope. This subpart establishes procedures for monitoring and reporting program performance of... grant and subgrant supported activities. ...

7 CFR 3015.90 - Scope.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.90 Scope. This subpart establishes procedures for monitoring and reporting program performance of... grant and subgrant supported activities. ...

Observer-based output feedback control of networked control systems with non-uniform sampling and time-varying delay

NASA Astrophysics Data System (ADS)

Meng, Su; Chen, Jie; Sun, Jian

2017-10-01

This paper investigates the problem of observer-based output feedback control for networked control systems with non-uniform sampling and time-varying transmission delay. The sampling intervals are assumed to vary within a given interval. The transmission delay belongs to a known interval. A discrete-time model is first established, which contains time-varying delay and norm-bounded uncertainties coming from non-uniform sampling intervals. It is then converted to an interconnection of two subsystems in which the forward channel is delay-free. The scaled small gain theorem is used to derive the stability condition for the closed-loop system. Moreover, the observer-based output feedback controller design method is proposed by utilising a modified cone complementary linearisation algorithm. Finally, numerical examples illustrate the validity and superiority of the proposed method.

46 CFR 232.6 - Financial report filing requirement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... RELATED ACTIVITIES UNIFORM FINANCIAL REPORTING REQUIREMENTS Income Statement § 232.6 Financial report filing requirement. (a) Reporting Frequency and Due Dates. The contractor shall file a semiannual... 46 Shipping 8 2010-10-01 2010-10-01 false Financial report filing requirement. 232.6 Section 232.6...

LSCA Final Reports: Second Series.

ERIC Educational Resources Information Center

Clark, Collin, Ed.

This document includes final summary reports from recent federally funded Library Services and Construction Act (LSCA) demonstration projects in California. While some projects reported at length and others provided the bare facts, reports are excerpted but published as received, without editing beyond a uniform first page. The Summary Report Form…

Hybrid slab-microchannel gel electrophoresis system

DOEpatents

Balch, J.W.; Carrano, A.V.; Davidson, J.C.; Koo, J.C.

1998-05-05

A hybrid slab-microchannel gel electrophoresis system is described. The hybrid system permits the fabrication of isolated microchannels for biomolecule separations without imposing the constraint of a totally sealed system. The hybrid system is reusable and ultimately much simpler and less costly to manufacture than a closed channel plate system. The hybrid system incorporates a microslab portion of the separation medium above the microchannels, thus at least substantially reducing the possibility of non-uniform field distribution and breakdown due to uncontrollable leakage. A microslab of the sieving matrix is built into the system by using plastic spacer materials and is used to uniformly couple the top plate with the bottom microchannel plate. 4 figs.

20 CFR 437.40 - Monitoring and reporting program performance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Monitoring and reporting program performance. 437.40 Section 437.40 Employees' Benefits SOCIAL SECURITY ADMINISTRATION UNIFORM ADMINISTRATIVE... Reports, Records, Retention, and Enforcement § 437.40 Monitoring and reporting program performance. (a...

7 CFR 3015.92 - Performance reports.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 15 2011-01-01 2011-01-01 false Performance reports. 3015.92 Section 3015.92..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.92 Performance reports. (a) Nonconstruction. The awarding agency shall, if it decides that...

7 CFR 3015.92 - Performance reports.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 15 2014-01-01 2014-01-01 false Performance reports. 3015.92 Section 3015.92..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.92 Performance reports. (a) Nonconstruction. The awarding agency shall, if it decides that...

7 CFR 3015.92 - Performance reports.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 15 2013-01-01 2013-01-01 false Performance reports. 3015.92 Section 3015.92..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.92 Performance reports. (a) Nonconstruction. The awarding agency shall, if it decides that...

7 CFR 3015.92 - Performance reports.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 15 2012-01-01 2012-01-01 false Performance reports. 3015.92 Section 3015.92..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Monitoring and Reporting Program Performance § 3015.92 Performance reports. (a) Nonconstruction. The awarding agency shall, if it decides that...

A scheme for the uniform mapping and monitoring of earth resources and environmental complexes using ERTS-1 imagery

NASA Technical Reports Server (NTRS)

Poulton, C. E. (Principal Investigator); Welch, R. I.

1973-01-01

There are no author-identified significant results in this report. Progress on plans for the development and testing of a practical procedure and system for the uniform mapping and monitoring of natural ecosystems and environmental complexes from space-acquired imagery is discussed. With primary emphasis on ERTS-1 imagery, but supported by appropriate aircraft photography as necessary, the objectives are to accomplish the following: (1) Develop and test in a few selected sites and areas of the western United States a standard format for an ecological and land use legend for making natural resource inventories on a simulated global basis. (2) Based on these same limited geographic areas, identify the potentialities and limitations of the legend concept for the recognition and annotation of ecological analogs and environmental complexes. An additional objective is to determine the optimum combination of space photography, aerial photography, ground data, human data analysis, and automatic data analysis for estimating crop yield in the rice growing areas of California and Louisiana.

Strain measurement in a concrete beam by use of the Brillouin-scattering-based distributed fiber sensor with single-mode fibers embedded in glass fiber reinforced polymer rods and bonded to steel reinforcing bars.

PubMed

Zeng, Xiaodong; Bao, Xiaoyi; Chhoa, Chia Yee; Bremner, Theodore W; Brown, Anthony W; DeMerchant, Michael D; Ferrier, Graham; Kalamkarov, Alexander L; Georgiades, Anastasis V

2002-08-20

The strain measurement of a 1.65-m reinforced concrete beam by use of a distributed fiber strain sensor with a 50-cm spatial resolution and 5-cm readout resolution is reported. The strain-measurement accuracy is +/-15 microepsilon (microm/m) according to the system calibration in the laboratory environment with non-uniform-distributed strain and +/-5 microepsilon with uniform strain distribution. The strain distribution has been measured for one-point and two-point loading patterns for optical fibers embedded in pultruded glass fiber reinforced polymer (GFRP) rods and those bonded to steel reinforcing bars. In the one-point loading case, the strain deviations are +/-7 and +/-15 microepsilon for fibers embedded in the GFRP rods and fibers bonded to steel reinforcing bars, respectively, whereas the strain deviation is +/-20 microepsilon for the two-point loading case.

New Flexible Channels for Room Temperature Tunneling Field Effect Transistors

PubMed Central

Hao, Boyi; Asthana, Anjana; Hazaveh, Paniz Khanmohammadi; Bergstrom, Paul L.; Banyai, Douglas; Savaikar, Madhusudan A.; Jaszczak, John A.; Yap, Yoke Khin

2016-01-01

Tunneling field effect transistors (TFETs) have been proposed to overcome the fundamental issues of Si based transistors, such as short channel effect, finite leakage current, and high contact resistance. Unfortunately, most if not all TFETs are operational only at cryogenic temperatures. Here we report that iron (Fe) quantum dots functionalized boron nitride nanotubes (QDs-BNNTs) can be used as the flexible tunneling channels of TFETs at room temperatures. The electrical insulating BNNTs are used as the one-dimensional (1D) substrates to confine the uniform formation of Fe QDs on their surface as the flexible tunneling channel. Consistent semiconductor-like transport behaviors under various bending conditions are detected by scanning tunneling spectroscopy in a transmission electron microscopy system (in-situ STM-TEM). As suggested by computer simulation, the uniform distribution of Fe QDs enable an averaging effect on the possible electron tunneling pathways, which is responsible for the consistent transport properties that are not sensitive to bending. PMID:26846587

New Flexible Channels for Room Temperature Tunneling Field Effect Transistors

DOE PAGES

Hao, Boyi; Asthana, Anjana; Hazaveh, Paniz Khanmohammadi; ...

2016-02-05

Tunneling field effect transistors (TFETs) have been proposed to overcome the fundamental issues of Si based transistors, such as short channel effect, finite leakage current, and high contact resistance. Unfortunately, most if not all TFETs are operational only at cryogenic temperatures. Here we report that iron (Fe) quantum dots functionalized boron nitride nanotubes (QDs-BNNTs) can be used as the flexible tunneling channels of TFETs at room temperatures. The electrical insulating BNNTs are used as the one-dimensional (1D) substrates to confine the uniform formation of Fe QDs on their surface as the flexible tunneling channel. Consistent semiconductor-like transport behaviors under variousmore » bending conditions are detected by scanning tunneling spectroscopy in a transmission electron microscopy system (insitu STM-TEM). Ultimately, as suggested by computer simulation, the uniform distribution of Fe QDs enable an averaging effect on the possible electron tunneling pathways, which is responsible for the consistent transport properties that are not sensitive to bending.« less

New Flexible Channels for Room Temperature Tunneling Field Effect Transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hao, Boyi; Asthana, Anjana; Hazaveh, Paniz Khanmohammadi

Tunneling field effect transistors (TFETs) have been proposed to overcome the fundamental issues of Si based transistors, such as short channel effect, finite leakage current, and high contact resistance. Unfortunately, most if not all TFETs are operational only at cryogenic temperatures. Here we report that iron (Fe) quantum dots functionalized boron nitride nanotubes (QDs-BNNTs) can be used as the flexible tunneling channels of TFETs at room temperatures. The electrical insulating BNNTs are used as the one-dimensional (1D) substrates to confine the uniform formation of Fe QDs on their surface as the flexible tunneling channel. Consistent semiconductor-like transport behaviors under variousmore » bending conditions are detected by scanning tunneling spectroscopy in a transmission electron microscopy system (insitu STM-TEM). Ultimately, as suggested by computer simulation, the uniform distribution of Fe QDs enable an averaging effect on the possible electron tunneling pathways, which is responsible for the consistent transport properties that are not sensitive to bending.« less

Detection of stress corrosion cracking and general corrosion of mild steel in simulated defense nuclear waste solutions using electrochemical noise analysis

NASA Astrophysics Data System (ADS)

Edgemon, G. L.; Danielson, M. J.; Bell, G. E. C.

1997-06-01

Underground waste tanks fabricated from mild steel store more than 253 million liters of high level radioactive waste from 50 years of weapons production at the Hanford Site. The probable modes of corrosion failures are reported as nitrate stress corrosion cracking and pitting. In an effort to develop a waste tank corrosion monitoring system, laboratory tests were conducted to characterize electrochemical noise data for both uniform and localized corrosion of mild steel and other materials in simulated waste environments. The simulated waste solutions were primarily composed of ammonium nitrate or sodium nitrate and were held at approximately 97°C. The electrochemical noise of freely corroding specimens was monitored, recorded and analyzed for periods ranging between 10 and 500 h. At the end of each test period, the specimens were examined to correlate electrochemical noise data with corrosion damage. Data characteristic of uniform corrosion and stress corrosion cracking are presented.

Development of a Double-Gauss Lens Based Setup for Optoacoustic Applications

PubMed Central

Choi, Hojong; Ryu, Jae-Myung; Yeom, Jung-Yeol

2017-01-01

In optoacoustic (photoacoustic) systems, different echo signal intensities such as amplitudes, center frequencies, and bandwidths need to be compensated by utilizing variable gain or time-gain compensation amplifiers. However, such electronic components can increase system complexities and signal noise levels. In this paper, we introduce a double-Gauss lens to generate a large field of view with uniform light intensity due to the low chromatic aberrations of the lens, thus obtaining uniform echo signal intensities across the field of view of the optoacoustic system. In order to validate the uniformity of the echo signal intensities in the system, an in-house transducer was placed at various positions above a tissue sample and echo signals were measured and compared with each other. The custom designed double-Gauss lens demonstrated negligible light intensity variation (±1.5%) across the illumination field of view (~2 cm diameter). When the transducer was used to measure echo signal from an eye of a bigeye tuna within a range of ±1 cm, the peak-to-peak amplitude, center frequency, and their −6 dB bandwidth variations were less than 2 mV, 1 MHz, and 6%, respectively. The custom designed double-Gauss lens can provide uniform light beam across a wide area while generating insignificant echo signal variations, and thus can lower the burden of the receiving electronics or signal processing in the optoacoustic system. PMID:28273794

Liquid Fuels: Pyrolytic Degradation and Fire Spread Behavior as Influenced by Buoyancy

NASA Technical Reports Server (NTRS)

Yeboah, Yaw D.; Malbrue, Courtney; Savage, Melane; Liao, Bo; Ross, Howard D. (Technical Monitor)

2001-01-01

This work is being conducted by the Combustion and Emission Control Lab in the Engineering Department at Clark Atlanta University under NASA Grant No. NCC3-707. The work aims at providing data to supplement the ongoing NASA research activities on fire spread across liquid pools by providing flow visualization and velocity measurements especially in the gas phase and gas-liquid interface. The fabrication, installation, and testing were completed during this reporting period. The system shakedown and detailed quantitative measurements with High Speed Video and Particle Image Velocimetry (PIV) systems using butanol as fuel were performed. New and interesting results, not previously reported in the literature, were obtained from the experiments using a modified NASA tray and butanol as fuel. Three distinct flame spread regimes, as previously reported, were observed. These were the pseudo-uniform regime below 20 C, the pulsating regime between 22 and 30 C and the uniform regime above about 31 C. In the pulsating regime the jump velocity appeared to be independent of the pool temperature. However, the retreat velocity between jumps appeared to depend on the initial pool temperature. The flame retreated before surging forwards with increasing brightness. Previous literature reported this phenomenon only under microgravity conditions. However, we observed such behavior in our normal gravity experiments. Mini-pulsations behind the flame front were also observed. Two or three of these pulsations were observed within a single flame front pulsating time period. The velocity vector maps of the gas and liquid phases ahead, during, and behind the flame front were characterized. At least one recirculation cell was observed right below the flame front.The size of the liquid phase vortex (recirculation cell) below the flame front appeared to decrease with increasing initial pool temperature. The experiments also showed how multiple vortices developed in the liquid phase. A large recirculation cell, which generally spins counterclockwise as the flame spread from right to left, was observed ahead of and near the flame front in the gas phase. Detailed quantitative measurements will be undertaken with the LDV and PIV systems using the modified NASA tray and propanol.

A comparison of intensity modulated x-ray therapy to intensity modulated proton therapy for the delivery of non-uniform dose distributions

NASA Astrophysics Data System (ADS)

Flynn, Ryan

2007-12-01

The distribution of biological characteristics such as clonogen density, proliferation, and hypoxia throughout tumors is generally non-uniform, therefore it follows that the optimal dose prescriptions should also be non-uniform and tumor-specific. Advances in intensity modulated x-ray therapy (IMXT) technology have made the delivery of custom-made non-uniform dose distributions possible in practice. Intensity modulated proton therapy (IMPT) has the potential to deliver non-uniform dose distributions as well, while significantly reducing normal tissue and organ at risk dose relative to IMXT. In this work, a specialized treatment planning system was developed for the purpose of optimizing and comparing biologically based IMXT and IMPT plans. The IMXT systems of step-and-shoot (IMXT-SAS) and helical tomotherapy (IMXT-HT) and the IMPT systems of intensity modulated spot scanning (IMPT-SS) and distal gradient tracking (IMPT-DGT), were simulated. A thorough phantom study was conducted in which several subvolumes, which were contained within a base tumor region, were boosted or avoided with IMXT and IMPT. Different boosting situations were simulated by varying the size, proximity, and the doses prescribed to the subvolumes, and the size of the phantom. IMXT and IMPT were also compared for a whole brain radiation therapy (WBRT) case, in which a brain metastasis was simultaneously boosted and the hippocampus was avoided. Finally, IMXT and IMPT dose distributions were compared for the case of non-uniform dose prescription in a head and neck cancer patient that was based on PET imaging with the Cu(II)-diacetyl-bis(N4-methylthiosemicarbazone (Cu-ATSM) hypoxia marker. The non-uniform dose distributions within the tumor region were comparable for IMXT and IMPT. IMPT, however, was capable of delivering the same non-uniform dose distributions within a tumor using a 180° arc as for a full 360° rotation, which resulted in the reduction of normal tissue integral dose by a factor of up to three relative to IMXT, and the complete sparing of organs at risk distal to the tumor region.

Room temperature enhanced red emission from novel Eu(3+) doped ZnO nanocrystals uniformly dispersed in nanofibers.

PubMed

Zhang, Yongzhe; Liu, Yanxia; Li, Xiaodong; Wang, Qi Jie; Xie, Erqing

2011-10-14

Achieving red emission from ZnO-based materials has long been a goal for researchers in order to realize, for instance, full-color display panels and solid-state light-emitting devices. However, the current technique using Eu(3+) doped ZnO for red emission generation has a significant drawback in that the energy transfer from ZnO to Eu(3+) is inefficient, resulting in a low intensity red emission. In this paper, we report an efficient energy transfer scheme for enhanced red emission from Eu(3+) doped ZnO nanocrystals by fabricating polymer nanofibers embedded with Eu(3+) doped ZnO nanocrystals to facilitate the energy transfer. In the fabrication, ZnO nanocrystals are uniformly dispersed in polymer nanofibers prepared by the high electrical field electrospinning technique. Enhanced red emission without defect radiation from the ZnO matrix is observed. Three physical mechanisms for this observation are provided and explained, namely a small ZnO crystal size, uniformity distribution of ZnO nanocrystals in polymers (PVA in this case), and strong bonding between ZnO and polymer through the -OH group bonding. These explanations are supported by high resolution transmission emission microscopy measurements, resonant Raman scattering characterizations, photoluminescence spectra and photoluminescence excitation spectra measurements. In addition, two models exploring the 'accumulation layer' and 'depletion layer' are developed to explain the reasons for the more efficient energy transfer in our ZnO nanocrystal system compared to that in the previous reports. This study provides an important approach to achieve enhanced energy transfer from nanocrystals to ions which could be widely adopted in rare earth ion doped materials. These discoveries also provide more insights into other energy transfer problems in, for example, dye-sensitized solar cells and quantum dot solar cells.

Clean focus, dose and CD metrology for CD uniformity improvement

NASA Astrophysics Data System (ADS)

Lee, Honggoo; Han, Sangjun; Hong, Minhyung; Kim, Seungyoung; Lee, Jieun; Lee, DongYoung; Oh, Eungryong; Choi, Ahlin; Kim, Nakyoon; Robinson, John C.; Mengel, Markus; Pablo, Rovira; Yoo, Sungchul; Getin, Raphael; Choi, Dongsub; Jeon, Sanghuck

2018-03-01

Lithography process control solutions require more exacting capabilities as the semiconductor industry goes forward to the 1x nm node DRAM device manufacturing. In order to continue scaling down the device feature sizes, critical dimension (CD) uniformity requires continuous improvement to meet the required CD error budget. In this study we investigate using optical measurement technology to improve over CD-SEM methods in focus, dose, and CD. One of the key challenges is measuring scanner focus of device patterns. There are focus measurement methods based on specially designed marks on scribe-line, however, one issue of this approach is that it will report focus of scribe line which is potentially different from that of the real device pattern. In addition, scribe-line marks require additional design and troubleshooting steps that add complexity. In this study, we investigated focus measurement directly on the device pattern. Dose control is typically based on using the linear correlation behavior between dose and CD. The noise of CD measurement, based on CD-SEM for example, will not only impact the accuracy, but also will make it difficult to monitor dose signature on product wafers. In this study we will report the direct dose metrology result using an optical metrology system which especially enhances the DUV spectral coverage to improve the signal to noise ratio. CD-SEM is often used to measure CD after the lithography step. This measurement approach has the advantage of easy recipe setup as well as the flexibility to measure critical feature dimensions, however, we observe that CD-SEM metrology has limitations. In this study, we demonstrate within-field CD uniformity improvement through the extraction of clean scanner slit and scan CD behavior by using optical metrology.

High-voltage electrode optimization towards uniform surface treatment by a pulsed volume discharge

NASA Astrophysics Data System (ADS)

Ponomarev, A. V.; Pedos, M. S.; Scherbinin, S. V.; Mamontov, Y. I.; Ponomarev, S. V.

2015-11-01

In this study, the shape and material of the high-voltage electrode of an atmospheric pressure plasma generation system were optimised. The research was performed with the goal of achieving maximum uniformity of plasma treatment of the surface of the low-voltage electrode with a diameter of 100 mm. In order to generate low-temperature plasma with the volume of roughly 1 cubic decimetre, a pulsed volume discharge was used initiated with a corona discharge. The uniformity of the plasma in the region of the low-voltage electrode was assessed using a system for measuring the distribution of discharge current density. The system's low-voltage electrode - collector - was a disc of 100 mm in diameter, the conducting surface of which was divided into 64 radially located segments of equal surface area. The current at each segment was registered by a high-speed measuring system controlled by an ARM™-based 32-bit microcontroller. To facilitate the interpretation of results obtained, a computer program was developed to visualise the results. The program provides a 3D image of the current density distribution on the surface of the low-voltage electrode. Based on the results obtained an optimum shape for a high-voltage electrode was determined. Uniformity of the distribution of discharge current density in relation to distance between electrodes was studied. It was proven that the level of non-uniformity of current density distribution depends on the size of the gap between electrodes. Experiments indicated that it is advantageous to use graphite felt VGN-6 (Russian abbreviation) as the material of the high-voltage electrode's emitting surface.

MEGA X: Molecular Evolutionary Genetics Analysis across Computing Platforms.

PubMed

Kumar, Sudhir; Stecher, Glen; Li, Michael; Knyaz, Christina; Tamura, Koichiro

2018-06-01

The Molecular Evolutionary Genetics Analysis (Mega) software implements many analytical methods and tools for phylogenomics and phylomedicine. Here, we report a transformation of Mega to enable cross-platform use on Microsoft Windows and Linux operating systems. Mega X does not require virtualization or emulation software and provides a uniform user experience across platforms. Mega X has additionally been upgraded to use multiple computing cores for many molecular evolutionary analyses. Mega X is available in two interfaces (graphical and command line) and can be downloaded from www.megasoftware.net free of charge.

The Oscillating Circular Airfoil on the Basis of Potential Theory

NASA Technical Reports Server (NTRS)

Schade, T.; Krienes, K.

1947-01-01

Proceeding from the thesis by W. Kinner the present report treats the problem of the circular airfoil in uniform airflow executing small oscillations, the amplitudes of which correspond to whole functions of the second degree in x and y. The pressure distribution is secured by means of Prandtl's acceleration potential. It results in a system of linear equations the coefficients of which can be calculated exactly with the aid of exponential functions and Hankel's functions. The equations necessary are derived in part I; the numerical calculation follows in part II.

Cerium-doped scintillating fused-silica fibers

NASA Astrophysics Data System (ADS)

Akchurin, N.; Cowden, C.; Damgov, J.; Dragoiu, C.; Dudero, P.; Faulkner, J.; Kunori, S.

2018-04-01

We report on a set of measurements made on (scintillating) cerium-doped fused-silica fibers using high-energy particle beams. These fibers were uniformly embedded in a copper absorber in order to utilize electromagnetic showers as a source of charged particles for generating signals. This new type of cerium-doped fiber potentially offers myriad new applications in calorimeters in high-energy physics, tracking systems, and beam monitoring detectors for future applications. The light yield, pulse shape, attenuation length, and light propagation speeds are given and discussed. Possible future applications are also explored.

Optimized Ce:LiCAF amplifier pumping configurations

NASA Astrophysics Data System (ADS)

Cadatal-Raduban, Marilou; Pham, Minh Hong; Gabayno, Jacque Lynn; Yamanoi, Kohei; Empizo, Melvin John F.; Shimizu, Toshihiko; Sarukura, Nobuhiko; Nguyen, Hung Dai; Yoshikawa, Akira; Fukuda, Tsuguo

2018-02-01

Two side-pumping schemes suitable for the development of an ultraviolet femtosecond amplifier system using a Ce3+:LiCaAlF6 crystal are reported. Firstly, a Bethune-type prismatic cell configuration that uniformly illuminates the four sides of a micro-pulling down method-grown crystal is used to amplify 290 nm, femtosecond pulses with no significant increase in pulse duration and B-integral. The second pumping scheme uses a two-side-pumped large crystal. These two side-pumping schemes can pave new possibilities for achieving high-energy ultraviolet femtosecond pulses.

Optimization and Calculation of Probability Performances of Processes of Storage and Processing of Refrigerator Containerized Cargoes

NASA Astrophysics Data System (ADS)

Nyrkov, A. P.; Sokolov, S. S.; Chernyi, S. G.; Shnurenko, A. A.; Pavlova, L. A.

2016-08-01

In the work the queueing system of the disconnected multi-channel type to which irregular, uniform or not uniform flows of requests with a unlimited latency period arrive is considered. The system is considered on an example of the container terminal having conditional-functional sections with a definite mark-to-space ratio on which the irregular inhomogeneous traffic flow with resultant intensity acts.

Towards an electronic national injury surveillance system in Saudi Arabia.

PubMed

Alanazi, F; Hussain, S A; Mandil, A; Alamro, N

2015-04-02

Given the need for a uniform, comprehensive, electronic nationwide surveillance system for injuries in Saudi Arabia, a system was designed with the objectives of establishing an epidemiologic profile of injuries in the country; evaluating injury indicators on an ongoing basis; identifying high-risk groups requiring specific interventions; monitoring and evaluating interventions for effectiveness; and producing reports to assist in planning and resource allocation. A special form for this purpose was designed, modified from validated forms used elsewhere for injury surveillance. This initiative of the Ministry of Health is also expected to help validate data collected by other sectors, such as the Ministry of Interior. This paper reviews the milestones of building the system and aims to prompt a debate within the scientific community, especially within the Eastern Mediterranean Region, about the best way to design injury surveillance systems for the Region in order to fine-tune the proposed system before its full-scale implementation.

Investigation of uniformity field generated from freeform lens with UV LED exposure system

NASA Astrophysics Data System (ADS)

Ciou, F. Y.; Chen, Y. C.; Pan, C. T.; Lin, P. H.; Lin, P. H.; Hsu, F. T.

2015-03-01

In the exposure process, the intensity and uniformity of light in the exposure area directly influenced the precision of products. UV-LED (Ultraviolet Light-Emitting Diode) exposure system was established to reduce the radiation leakage and increase the energy efficiency for energy saving. It is a trend that conventional mercury lamp could be replaced with UV-LED exposure system. This study was based on the law of conservation of energy and law of refraction of optical field distributing on the target plane. With these, a freeform lens with uniform light field of main exposure area could be designed. The light outside the exposure area could be concentrated into the area to improve the intensity of light. The refraction index and UV transmittance of Polydimethylsiloxane (PDMS) is 1.43 at 385 nm wavelength and 85-90%, respectively. The PDMS was used to fabricate the optics lens for UV-LEDs. The average illumination and the uniformity could be obtained by increasing the number of UV-LEDs and the spacing of different arrangement modes. After exposure process with PDMS lens, about 5% inaccuracy was obtained. Comparing to 10% inaccuracy of general exposure system, it shows that it is available to replace conventional exposure lamp with using UV-LEDs.

Optical design of an in vivo laparoscopic lighting system.

PubMed

Liu, Xiaolong; Abdolmalaki, Reza Yazdanpanah; Mancini, Gregory J; Tan, Jindong

2017-12-01

This paper proposes an in vivo laparoscopic lighting system design to address the illumination issues, namely poor lighting uniformity and low optical efficiency, existing in the state-of-the-art in vivo laparoscopic cameras. The transformable design of the laparoscopic lighting system is capable of carrying purposefully designed freeform optical lenses for achieving lighting performance with high illuminance uniformity and high optical efficiency in a desired target region. To design freeform optical lenses for extended light sources such as LEDs with Lambertian light intensity distributions, we present an effective and complete freeform optical design method. The procedures include (1) ray map computation by numerically solving a standard Monge-Ampere equation; (2) initial freeform optical surface construction by using Snell's law and a lens volume restriction; (3) correction of surface normal vectors due to accumulated errors from the initially constructed surfaces; and (4) feedback modification of the solution to deal with degraded illuminance uniformity caused by the extended sizes of the LEDs. We employed an optical design software package to evaluate the performance of our laparoscopic lighting system design. The simulation results show that our design achieves greater than 95% illuminance uniformity and greater than 89% optical efficiency (considering Fresnel losses) for illuminating the target surgical region. (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

Solar concentrator with diffuser segments

NASA Astrophysics Data System (ADS)

Esparza, Diego; Moreno, Ivan

2011-08-01

Solar energy systems use concentrating optics with photovoltaic cells for optimizing the performance. Advanced concentrators are designed to maximize both the light collection and the spatial uniformity of radiation. This is important because irradiance uniformity is critical for all types of photovoltaic cells. This is difficult to achieve with traditional concentrators, which are built with polished optical surfaces. In this work we propose a new concept of solar concentrator which uses small diffuser segments in key points to increase the irradiation uniformity. We experimentally demonstrate this new concept by analyzing the effects on both efficiency and irradiance uniformity due to the incorporation of scattering ribbons in a compound parabolic concentrator.

Underestimates of unintentional firearm fatalities: comparing Supplementary Homicide Report data with the National Vital Statistics System

PubMed Central

Barber, C; Hemenway, D; Hochstadt, J; Azrael, D

2002-01-01

Objective: A growing body of evidence suggests that the nation's vital statistics system undercounts unintentional firearm deaths that are not self inflicted. This issue was examined by comparing how unintentional firearm injuries identified in police Supplementary Homicide Report (SHR) data were coded in the National Vital Statistics System. Methods: National Vital Statistics System data are based on death certificates and divide firearm fatalities into six subcategories: homicide, suicide, accident, legal intervention, war operations, and undetermined. SHRs are completed by local police departments as part of the FBI's Uniform Crime Reports program. The SHR divides homicides into two categories: "murder and non-negligent manslaughter" (type A) and "negligent manslaughter" (type B). Type B shooting deaths are those that are inflicted by another person and that a police investigation determined were inflicted unintentionally, as in a child killing a playmate after mistaking a gun for a toy. In 1997, the SHR classified 168 shooting victims this way. Using probabilistic matching, 140 of these victims were linked to their death certificate records. Results: Among the 140 linked cases, 75% were recorded on the death certificate as homicides and only 23% as accidents. Conclusion: Official data from the National Vital Statistics System almost certainly undercount firearm accidents when the victim is shot by another person. PMID:12226128

Grading dermatologic adverse events of cancer treatments: the Common Terminology Criteria for Adverse Events Version 4.0.

PubMed

Chen, Alice P; Setser, Ann; Anadkat, Milan J; Cotliar, Jonathan; Olsen, Elise A; Garden, Benjamin C; Lacouture, Mario E

2012-11-01

Dermatologic adverse events to cancer therapies have become more prevalent and may to lead to dose modifications or discontinuation of life-saving or prolonging treatments. This has resulted in a new collaboration between oncologists and dermatologists, which requires accurate cataloging and grading of side effects. The Common Terminology Criteria for Adverse Events Version 4.0 is a descriptive terminology and grading system that can be used for uniform reporting of adverse events. A proper understanding of this standardized classification system is essential for dermatologists to properly communicate with all physicians caring for patients with cancer. Copyright © 2012 American Academy of Dermatology, Inc. Published by Mosby, Inc. All rights reserved.

Event-Driven Messaging for Offline Data Quality Monitoring at ATLAS

NASA Astrophysics Data System (ADS)

Onyisi, Peter

2015-12-01

During LHC Run 1, the information flow through the offline data quality monitoring in ATLAS relied heavily on chains of processes polling each other's outputs for handshaking purposes. This resulted in a fragile architecture with many possible points of failure and an inability to monitor the overall state of the distributed system. We report on the status of a project undertaken during the LHC shutdown to replace the ad hoc synchronization methods with a uniform message queue system. This enables the use of standard protocols to connect processes on multiple hosts; reliable transmission of messages between possibly unreliable programs; easy monitoring of the information flow; and the removal of inefficient polling-based communication.

Substance Abuse Treatment in Adult and Juvenile Correctional Facilities: Findings from the Uniform Facility Data Set 1997 Survey of Correctional Facilities.

ERIC Educational Resources Information Center

Marsden, Mary Ellen, Ed.; Straw, Richard S., Ed.

This report presents methodology and findings from the Uniform Facility Data Set (UFDS) 1997 Survey of Correctional Facilities, which surveyed about 7,600 adult and juvenile correctional facilities to identify those that provide on-site substance abuse treatment to their inmates or residents. The survey assesses substance abuse treatment provided…

Dynamic mobility application policy analysis : policy and institutional issues for Response, Emergency Staging and Communications, Uniform Management, and Evacuation (R.E.S.C.U.M.E).

DOT National Transportation Integrated Search

2015-07-01

This report documents policy considerations for Response, Emergency Staging and Communications, Uniform Management, and Evacuation (R.E.S.C.U.M.E). R.E.S.C.U.M.E. comprises a "bundle" of mobility applications that use existing and new connected vehic...

Pixel-Wise-Inter/Intra-Channel Color and Luminance Uniformity Corrections for Multi-Channel Projection Displays

DTIC Science & Technology

2016-08-11

Journal Article 3. DATES COVERED (From – To) Jan 2015 – Dec 2015 4. TITLE AND SUBTITLE PIXEL-WISE INTER/INTRA-CHANNEL COLOR & LUMINANCE UNIFORMITY...Conference Dayton, Ohio – 28-29 June 2016 14. ABSTRACT Inter- and intra-channel color and luminance are generally non-uniform in multi-channel...projection display systems. Several methods have been proposed to correct for both inter- and intra-channel color and luminance variation in multi-channel

Role of Cytokines and Neurotrophins in the Central Nervous System in Venezuelan Equine Encephalitis Pathogenesis

DTIC Science & Technology

2001-03-21

copyright owner, and will save and hold harmless the Uniformed Services University of the Health Sciences from any damage which may arise from such a...Immunology Uniformed Services University of the Health Sciences 11 iii ABSTRACT Title of thesis: Role of Cytokines and Neurotrophins in the Central...Kristen M. K. Catlin Thesis submitted to the Faculty of the Department of Microbiology and Immunology Graduate Program of the Uniformed Services of the

Effect of Uniform Design on the Speed of Combat Tourniquet Application: A Simulation Study.

PubMed

Higgs, Andrew R; Maughon, Michael J; Ruland, Robert T; Reade, Michael C

2016-08-01

Tourniquets are issued to deployed members of both the United States (U.S. military and the Australian Defence Force (ADF). The ease of removing the tourniquet from the pocket of the combat uniform may influence its time to application. The ADF uniform uses buttons to secure the pocket, whereas the U.S. uniform uses a hook and loop fastener system. National differences in training may influence the time to and effectiveness of tourniquet application. To compare the time taken to retrieve and apply a tourniquet from the pocket of the Australian and the U.S. combat uniform and compare the effectiveness of tourniquet application. Twenty participants from both nations were randomly selected. Participants were timed on their ability to remove a tourniquet from their pockets and then apply it effectively. The U.S. personnel removed their tourniquets in shorter time (median 2.5 seconds) than Australians (median 5.72 seconds, p < 0.0001). ADF members (mean 41.36 seconds vs. 58.87 seconds, p < 0.037) applied the tourniquet more rapidly once removed from the pocket and trended to apply it more effectively (p = 0.1). The closure system of pockets on the combat uniform might influence the time taken to apply a tourniquet. Regular training might also reduce the time taken to apply a tourniquet effectively. Reprint & Copyright © 2016 Association of Military Surgeons of the U.S.

A DSP-based neural network non-uniformity correction algorithm for IRFPA

NASA Astrophysics Data System (ADS)

Liu, Chong-liang; Jin, Wei-qi; Cao, Yang; Liu, Xiu

2009-07-01

An effective neural network non-uniformity correction (NUC) algorithm based on DSP is proposed in this paper. The non-uniform response in infrared focal plane array (IRFPA) detectors produces corrupted images with a fixed-pattern noise(FPN).We introduced and analyzed the artificial neural network scene-based non-uniformity correction (SBNUC) algorithm. A design of DSP-based NUC development platform for IRFPA is described. The DSP hardware platform designed is of low power consumption, with 32-bit fixed point DSP TMS320DM643 as the kernel processor. The dependability and expansibility of the software have been improved by DSP/BIOS real-time operating system and Reference Framework 5. In order to realize real-time performance, the calibration parameters update is set at a lower task priority then video input and output in DSP/BIOS. In this way, calibration parameters updating will not affect video streams. The work flow of the system and the strategy of real-time realization are introduced. Experiments on real infrared imaging sequences demonstrate that this algorithm requires only a few frames to obtain high quality corrections. It is computationally efficient and suitable for all kinds of non-uniformity.

21 CFR 1403.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... OFFICE OF NATIONAL DRUG CONTROL POLICY UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE... Status Report” (or other equivalent report); (2) For construction grants, the SF-271 “Outlay Report and Request for Reimbursement” (or other equivalent report). Federally recognized Indian tribal government...

25 CFR 276.8 - Financial reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Financial reporting requirements. 276.8 Section 276.8... ASSISTANCE ACT PROGRAM UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS § 276.8 Financial reporting requirements. Requirements for grantees to report financial information to the Bureau, and to request advances...

Financial Management: Corps of Engineers Equipment Reporting on Financial Statements for FY 2002

DTIC Science & Technology

2003-08-20

U.S. Army Corps of Engineers civil service and uniformed officers responsible for financial reporting of equipment should read this report. It...discusses the management controls that are necessary to support the financial reporting of equipment on financial statements.

25 CFR 276.8 - Financial reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Financial reporting requirements. 276.8 Section 276.8... ASSISTANCE ACT PROGRAM UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS § 276.8 Financial reporting requirements. Requirements for grantees to report financial information to the Bureau, and to request advances...

45 CFR 1183.40 - Monitoring and reporting program performance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... FOUNDATION ON THE ARTS AND THE HUMANITIES INSTITUTE OF MUSEUM AND LIBRARY SERVICES UNIFORM ADMINISTRATIVE... must cover each program, function or activity. (b) Nonconstruction performance reports. The Federal...

45 CFR 1174.40 - Monitoring and reporting program performance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... FOUNDATION ON THE ARTS AND THE HUMANITIES NATIONAL ENDOWMENT FOR THE HUMANITIES UNIFORM ADMINISTRATIVE... developments. Events may occur between the scheduled performance reporting dates which have significant impact...

Assessing curriculum effectiveness: a survey of Uniformed Services University medical school graduates.

PubMed

Picho, Katherine; Gilliland, William R; Artino, Anthony R; DeZee, Kent J; Dong, Ting; McManigle, John E; Cruess, David F; Durning, Steven J

2015-04-01

This study assessed alumni perceptions of their preparedness for clinical practice using the Accreditation Council for Graduate Medical Education (ACGME) competencies. We hypothesized that our alumni's perception of preparedness would be highest for military-unique practice and professionalism and lowest for system-based practice and practice-based learning and improvement. 1,189 alumni who graduated from the Uniformed Services University (USU) between 1980 and 2001 completed a survey modeled to assess the ACGME competencies on a 5-point, Likert-type scale. Specifically, self-reports of competencies related to patient care, communication and interpersonal skills, medical knowledge, professionalism, systems-based practice, practice-based learning and improvement, and military-unique practice were evaluated. Consistent with our expectations as the nation's military medical school, our graduates were most confident in their preparedness for military-unique practice, which included items assessing military leadership (M = 4.30, SD = 0.65). USU graduates also indicated being well prepared for the challenges of residency education in the domain of professionalism (M = 4.02, SD = 0.72). Self-reports were also high for competencies related to patient care (M = 3.86, SD = 0.68), communication and interpersonal skills (M = 3.88, SD = 0.66), and medical knowledge (M = 3.78, SD = 0.73). Consistent with expectations, systems-based practice (M = 3.50, SD = 0.70) and practice-based learning and improvement (M = 3.57, SD = 0.62) were the lowest rated competencies, although self-reported preparedness was still quite high. Our findings suggest that, from the perspective of our graduates, USU is providing both an effective military-unique curriculum and is preparing trainees for residency training. Further, these results support the notion that graduates are prepared to lead and to practice medicine in austere environments. Compared to other competencies that were assessed, self-ratings for systems-based practice and practice-based learning and improvement were the lowest, which suggests the need to continue to improve USU education in these areas. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

Lackland Air Force Base Phase II Uniform Issue: Baseline Report

DTIC Science & Technology

2011-05-01

Lectures on uniform wearing and care are given 1-2 ORGANIZATION The remainder of this report includes two...sp ec ts al te ra tio ns A pp ro ve d to U S A F sp ec ? Tr ai ne es p ac k ite m s in d uf fle Y es A ll ite m s in sp ec te d? In ve nt...First alteration Second alteration Third alteration Pe rc en ta ge o f t ro us er s al te re d 0% 10% 20% 30% 40% 50% 60% 70% 80%

Response to non-uniform salinity in the root zone of the halophyte Atriplex nummularia: growth, photosynthesis, water relations and tissue ion concentrations

PubMed Central

Bazihizina, Nadia; Colmer, Timothy D.; Barrett-Lennard, Edward G.

2009-01-01

Background and Aims Soil salinity is often heterogeneous, yet the physiology of halophytes has typically been studied with uniform salinity treatments. An evaluation was made of the growth, net photosynthesis, water use, water relations and tissue ions in the halophytic shrub Atriplex nummularia in response to non-uniform NaCl concentrations in a split-root system. Methods Atriplex nummularia was grown in a split-root system for 21 d, with either the same or two different NaCl concentrations (ranging from 10 to 670 mm), in aerated nutrient solution bathing each root half. Key Results Non-uniform salinity, with high NaCl in one root half (up to 670 mm) and 10 mm in the other half, had no effect on shoot ethanol-insoluble dry mass, net photosynthesis or shoot pre-dawn water potential. In contrast, a modest effect occurred for leaf osmotic potential (up to 30 % more solutes compared with uniform 10 mm NaCl treatment). With non-uniform NaCl concentrations (10/670 mm), 90 % of water was absorbed from the low salinity side, and the reduction in water use from the high salinity side caused whole-plant water use to decrease by about 30 %; there was no compensatory water uptake from the low salinity side. Leaf Na+ and Cl− concentrations were 1·9- to 2·3-fold higher in the uniform 670 mm treatment than in the 10/670 mm treatment, whereas leaf K+ concentrations were 1·2- to 2·0-fold higher in the non-uniform treatment. Conclusions Atriplex nummularia with one root half in 10 mm NaCl maintained net photosynthesis, shoot growth and shoot water potential even when the other root half was exposed to 670 mm NaCl, a concentration that inhibits growth by 65 % when uniform in the root zone. Given the likelihood of non-uniform salinity in many field situations, this situation would presumably benefit halophyte growth and physiology in saline environments. PMID:19556265

Vertical uniformity of cells and nuclei in epithelial monolayers.

PubMed

Neelam, Srujana; Hayes, Peter Robert; Zhang, Qiao; Dickinson, Richard B; Lele, Tanmay P

2016-01-22

Morphological variability in cytoskeletal organization, organelle position and cell boundaries is a common feature of cultured cells. Remarkable uniformity and reproducibility in structure can be accomplished by providing cells with defined geometric cues. Cells in tissues can also self-organize in the absence of directing extracellular cues; however the mechanical principles for such self-organization are not understood. We report that unlike horizontal shapes, the vertical shapes of the cell and nucleus in the z-dimension are uniform in cells in cultured monolayers compared to isolated cells. Apical surfaces of cells and their nuclei in monolayers were flat and heights were uniform. In contrast, isolated cells, or cells with disrupted cell-cell adhesions had nuclei with curved apical surfaces and variable heights. Isolated cells cultured within micron-sized square wells displayed flat cell and nuclear shapes similar to cells in monolayers. Local disruption of nuclear-cytoskeletal linkages resulted in spatial variation in vertical uniformity. These results suggest that competition between cell-cell pulling forces that expand and shorten the vertical cell cross-section, thereby widening and flattening the nucleus, and the resistance of the nucleus to further flattening results in uniform cell and nuclear cross-sections. Our results reveal the mechanical principles of self-organized vertical uniformity in cell monolayers.

Electroluminescence from InGaN/GaN multi-quantum-wells nanorods light-emitting diodes positioned by non-uniform electric fields.

PubMed

Park, Hyunik; Kim, Byung-Jae; Kim, Jihyun

2012-11-05

We report that the nanorod light-emitting diodes (LEDs) with InGaN/GaN multi-quantum-wells (MQWs) emitted bright electroluminescence (EL) after they were positioned and aligned by non-uniform electric fields. Firstly, thin film LED structures with MQWs on sapphire substrate were coated with SiO(2) nanospheres, followed by inductively-coupled plasma etch to create nanorod-shapes with MQWs, which were transferred to the pre-patterned SiO(2)/Si wafer. This method allowed us to obtain nanorod LEDs with uniform length, diameter and qualities. Dielectrophoretic force created by non-uniform electric field was very effective at positioning the processed nanorods on the pre-patterned contacts. After aligned by non-uniform electric field, we observed bright EL from many nanorods, which had both cases (p-GaN/MQWs/n-GaN or n-GaN/MQWs/p-GaN). Therefore, bright ELs at different locations were observed under the various bias conditions.

Comparison of characteristics and downstream uniformity of linear-field and cross-field atmospheric pressure plasma jet array in He

NASA Astrophysics Data System (ADS)

Zhang, Bo; Fang, Zhi; Liu, Feng; Zhou, Renwu; Zhou, Ruoyu

2018-06-01

Using an atmospheric pressure plasma jet array is an effective way for expanding the treatment area of a single jet, and generating arrays with well downstream uniformity is of great interest for its applications. In this paper, a plasma jet array in helium is generated in a linear-field jet array with a ring-ring electrode structure excited by alternating current. The characteristics and downstream uniformity of the array and their dependence on the applied voltage and gas flow rate are investigated through optical, electrical, and Schlieren diagnostics. The results are compared with those of our reported work of a cross-field jet array with a needle-ring electrode structure. The results show that the linear-field jet array can generate relatively large-scale plasma with better uniformity and longer plumes than the cross-field case. The divergences observed in gas channels and the plasma plume trajectories are much less than those of the cross-field one. The deflection angle of lateral plumes is less than 6°, which is independent of the gas flow rate and applied voltage. The maximum downstream plumes of 23 mm can be obtained at 7 kV peak applied voltage and 4 l/min gas flow rate. The better uniformity of linear-field jet arrays is due to the effective suppression of hydrodynamic and electrical interactions among the jets in the arrays with a more uniform electric field distribution. The hydrodynamic interaction induced by the gas heating in the linear-field jet array is less than that of the cross-field one. The more uniform electric field distribution in the linear-field jet arrays can reduce the divergence of the propagation trajectories of the plasma plumes. It will generate less residual charge between the adjacent discharges and thus can reduce the accumulation effect of Coulomb force between the plasma plumes. The reported results can help design controllable and scalable plasma jet arrays with well uniformity for material surface and biomedical treatments.

Condenser optics, partial coherence, and imaging for soft-x-ray projection lithography.

PubMed

Sommargren, G E; Seppala, L G

1993-12-01

A condenser system couples the radiation source to an imaging system, controlling the uniformity and partial coherence at the object, which ultimately affects the characteristics of the aerial image. A soft-x-ray projection lithography system based on a ring-field imaging system and a laser-produced plasma x-ray source places considerable constraints on the design of a condenser system. Two designs are proposed, critical illumination and Köhler illumination, each of which requires three mirrors and scanning for covering the entire ring field with the required uniformity and partial coherence. Images based on Hopkins' formulation of partially coherent imaging are simulated.

45 CFR 1157.40 - Monitoring and reporting program performance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... FOUNDATION ON THE ARTS AND THE HUMANITIES NATIONAL ENDOWMENT FOR THE ARTS UNIFORM ADMINISTRATIVE REQUIREMENTS... developments. Events may occur between the scheduled performance reporting dates which have significant impact...

Applications of MICP source for next-generation photomask process

NASA Astrophysics Data System (ADS)

Kwon, Hyuk-Joo; Chang, Byung-Soo; Choi, Boo-Yeon; Park, Kyung H.; Jeong, Soo-Hong

2000-07-01

As critical dimensions of photomask extends into submicron range, critical dimension uniformity, edge roughness, macro loading effect, and pattern slope become tighter than before. Fabrication of photomask relies on the ability to pattern features with anisotropic profile. To improve critical dimension uniformity, dry etcher is one of the solution and inductively coupled plasma (ICP) sources have become one of promising high density plasma sources for dry etcher. In this paper, we have utilized dry etcher system with multi-pole ICP source for Cr etch and MoSi etch and have investigated critical dimension uniformity, slope, and defects. We will present dry etch process data by process optimization of newly designed dry etcher system. The designed pattern area is 132 by 132 mm2 with 23 by 23 matrix test patterns. 3 (sigma) of critical dimension uniformity is below 12 nm at 0.8 - 3.0 micrometers . In most cases, we can obtain zero defect masks which is operated by face- down loading.

Integrate-and-fire models with an almost periodic input function

NASA Astrophysics Data System (ADS)

Kasprzak, Piotr; Nawrocki, Adam; Signerska-Rynkowska, Justyna

2018-02-01

We investigate leaky integrate-and-fire models (LIF models for short) driven by Stepanov and μ-almost periodic functions. Special attention is paid to the properties of the firing map and its displacement, which give information about the spiking behavior of the considered system. We provide conditions under which such maps are well-defined and are uniformly continuous. We show that the LIF models with Stepanov almost periodic inputs have uniformly almost periodic displacements. We also show that in the case of μ-almost periodic drives it may happen that the displacement map is uniformly continuous, but is not μ-almost periodic (and thus cannot be Stepanov or uniformly almost periodic). By allowing discontinuous inputs, we extend some previous results, showing, for example, that the firing rate for the LIF models with Stepanov almost periodic input exists and is unique. This is a starting point for the investigation of the dynamics of almost-periodically driven integrate-and-fire systems.

The oldest magnetic record in our solar system identified using nanometric imaging and numerical modeling.

PubMed

Shah, Jay; Williams, Wyn; Almeida, Trevor P; Nagy, Lesleis; Muxworthy, Adrian R; Kovács, András; Valdez-Grijalva, Miguel A; Fabian, Karl; Russell, Sara S; Genge, Matthew J; Dunin-Borkowski, Rafal E

2018-03-21

Recordings of magnetic fields, thought to be crucial to our solar system's rapid accretion, are potentially retained in unaltered nanometric low-Ni kamacite (~ metallic Fe) grains encased within dusty olivine crystals, found in the chondrules of unequilibrated chondrites. However, most of these kamacite grains are magnetically non-uniform, so their ability to retain four-billion-year-old magnetic recordings cannot be estimated by previous theories, which assume only uniform magnetization. Here, we demonstrate that non-uniformly magnetized nanometric kamacite grains are stable over solar system timescales and likely the primary carrier of remanence in dusty olivine. By performing in-situ temperature-dependent nanometric magnetic measurements using off-axis electron holography, we demonstrate the thermal stability of multi-vortex kamacite grains from the chondritic Bishunpur meteorite. Combined with numerical micromagnetic modeling, we determine the stability of the magnetization of these grains. Our study shows that dusty olivine kamacite grains are capable of retaining magnetic recordings from the accreting solar system.

Legendre-Tau approximation for functional differential equations. Part 3: Eigenvalue approximations and uniform stability

NASA Technical Reports Server (NTRS)

Ito, K.

1984-01-01

The stability and convergence properties of the Legendre-tau approximation for hereditary differential systems are analyzed. A charactristic equation is derived for the eigenvalues of the resulting approximate system. As a result of this derivation the uniform exponential stability of the solution semigroup is preserved under approximation. It is the key to obtaining the convergence of approximate solutions of the algebraic Riccati equation in trace norm.

Composite Reinforcement using Boron Nitride Nanotubes

DTIC Science & Technology

2016-11-15

atomistic environment, which often results in notable changes of its binding to the system. By contrast, Cu and Ti exhibits quite uniform behaviour ...contrast, Cu and Ti exhibits quite uniform behaviour and hardly change their binding energy with tube size for the systems investigated. Studies on...reinforced Cu is rather brittle and therefore comparison of the behaviour of Al, Ti and Cu is important, and also because Cu is used in alloys to produce

Design and analysis of reflector for uniform light-emitting diode illuminance.

PubMed

Tsai, Chung-Yu

2013-05-01

A light-emitting diode (LED) projection system is proposed, composed of an LED chip and a variable-focus-parabolic (VFP) reflector, in which the focal length varies as a function of the vertical displacement of the incidence point relative to the horizontal centerline of the LED chip. The light-ray paths within the projection system are analyzed using an exact analytical model and a skew-ray tracing approach. The profile of the proposed VFP reflector and the position of the LED chip are then optimized in such a way as to enhance the uniformity of the illuminance distribution on the target region of the image plane. The validity of the optimized design is demonstrated by means of ZEMAX simulations. It is shown that the optimized VFP projector system yields a significant improvement in illuminance uniformity compared to conventional spherical and parabolic projectors and therefore minimizes the glare effect.

Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conover, David R.; Crawford, Aladsair J.; Viswanathan, Vilayanur V.

2014-06-01

The Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems (PNNL-22010) was first issued in November 2012 as a first step toward providing a foundational basis for developing an initial standard for the uniform measurement and expression of energy storage system (ESS) performance. Its subsequent use in the field and review by the protocol working group and most importantly the users’ subgroup and the thermal subgroup has led to the fundamental modifications reflected in this update of the 2012 Protocol. As an update of the 2012 Protocol, this document (the June 2014 Protocol) is intended to supersedemore » its predecessor and be used as the basis for measuring and expressing ESS performance. The foreword provides general and specific details about what additions, revisions, and enhancements have been made to the 2012 Protocol and the rationale for them in arriving at the June 2014 Protocol.« less

Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conover, David R.; Crawford, Aladsair J.; Fuller, Jason C.

The Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems (PNNL-22010) was first issued in November 2012 as a first step toward providing a foundational basis for developing an initial standard for the uniform measurement and expression of energy storage system (ESS) performance. Based on experiences with the application and use of that document, and to include additional ESS applications and associated duty cycles, test procedures and performance metrics, a first revision of the November 2012 Protocol was issued in June 2014 (PNNL 22010 Rev. 1). As an update of the 2014 revision 1 to the Protocol,more » this document (the March 2016 revision 2 to the Protocol) is intended to supersede the June 2014 revision 1 to the Protocol and provide a more user-friendly yet more robust and comprehensive basis for measuring and expressing ESS performance.« less

28 CFR 66.40 - Monitoring and reporting program performance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... performance. 66.40 Section 66.40 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) UNIFORM... Requirements Reports, Records, Retention, and Enforcement § 66.40 Monitoring and reporting program performance... assure compliance with applicable Federal requirements and that performance goals are being achieved...

45 CFR 74.51 - Monitoring and reporting program performance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... two copies of performance reports. (f) Recipients shall immediately notify the HHS awarding agency of... UNIFORM ADMINISTRATIVE REQUIREMENTS FOR AWARDS AND SUBAWARDS TO INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NONPROFIT ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Reports and...

45 CFR 74.51 - Monitoring and reporting program performance.

Code of Federal Regulations, 2013 CFR

2013-10-01

... two copies of performance reports. (f) Recipients shall immediately notify the HHS awarding agency of... UNIFORM ADMINISTRATIVE REQUIREMENTS FOR AWARDS AND SUBAWARDS TO INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NONPROFIT ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Reports and...

45 CFR 74.51 - Monitoring and reporting program performance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... two copies of performance reports. (f) Recipients shall immediately notify the HHS awarding agency of... UNIFORM ADMINISTRATIVE REQUIREMENTS FOR AWARDS AND SUBAWARDS TO INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NONPROFIT ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Reports and...

45 CFR 74.51 - Monitoring and reporting program performance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... two copies of performance reports. (f) Recipients shall immediately notify the HHS awarding agency of... UNIFORM ADMINISTRATIVE REQUIREMENTS FOR AWARDS AND SUBAWARDS TO INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NONPROFIT ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Reports and...

Solution of linear systems by a singular perturbation technique

NASA Technical Reports Server (NTRS)

Ardema, M. D.

1976-01-01

An approximate solution is obtained for a singularly perturbed system of initial valued, time invariant, linear differential equations with multiple boundary layers. Conditions are stated under which the approximate solution converges uniformly to the exact solution as the perturbation parameter tends to zero. The solution is obtained by the method of matched asymptotic expansions. Use of the results for obtaining approximate solutions of general linear systems is discussed. An example is considered to illustrate the method and it is shown that the formulas derived give a readily computed uniform approximation.

Uniforms, status and professional boundaries in hospital.

PubMed

Timmons, Stephen; East, Linda

2011-11-01

Despite their comparative neglect analytically, uniforms play a key role in the delineation of occupational boundaries and the formation of professional identity in healthcare. This paper analyses a change to the system of uniforms in one UK hospital, where management have required all professions (with the exception of doctors) to wear the same 'corporate' uniform. Focus groups were conducted with the professionals and patients. We analyse this initiative as a kind of McDonaldisation, seeking to create a new 'corporate' worker whose allegiance is principally to the organisation, rather than a profession. Our findings show how important uniforms are to their wearers, both in terms of the defence of professional boundaries and status, as well as the construction of professional identity. © 2011 The Authors. Sociology of Health & Illness © 2011 Foundation for the Sociology of Health & Illness/Blackwell Publishing Ltd.

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers

PubMed Central

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-01-01

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work. PMID:28772954

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers.

PubMed

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-05-29

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

Detecting Uniform Areas for Vicarious Calibration using Landsat TM Imagery: A Study using the Arabian and Saharan Deserts

NASA Technical Reports Server (NTRS)

Hilbert, Kent; Pagnutti, Mary; Ryan, Robert; Zanoni, Vicki

2002-01-01

This paper discusses a method for detecting spatially uniform sites need for radiometric characterization of remote sensing satellites. Such information is critical for scientific research applications of imagery having moderate to high resolutions (<30-m ground sampling distance (GSD)). Previously published literature indicated that areas with the African Saharan and Arabian deserts contained extremely uniform sites with respect to spatial characteristics. We developed an algorithm for detecting site uniformity and applied it to orthorectified Landsat Thematic Mapper (TM) imagery over eight uniform regions of interest. The algorithm's results were assessed using both medium-resolution (30-m GSD) Landsat 7 ETM+ and fine-resolution (<5-m GSD) IKONOS multispectral data collected over sites in Libya and Mali. Fine-resolution imagery over a Libyan site exhibited less than 1 percent nonuniformity. The research shows that Landsat TM products appear highly useful for detecting potential calibration sites for system characterization. In particular, the approach detected spatially uniform regions that frequently occur at multiple scales of observation.

Measurement of non-uniform residual stresses by combined Moiré interferometry and hole-drilling method: Theory, experimental method and applications

NASA Astrophysics Data System (ADS)

Ya, Min; Dai, Fulong; Xie, Huimin; Lü, Jian

2003-12-01

Hole-drilling method is one of the most convenient methods for engineering residual stress measurement. Combined with moiré interferometry to obtain the relaxed whole-field displacement data, hole-drilling technique can be used to solve non-uniform residual stress problems, both in-depth and in-plane. In this paper, the theory of moiré interferometry and incremental hole-drilling (MIIHD) for non-uniform residual stress measurement is introduced. Three dimensional finite element model is constructed by ABAQUS to obtain the coefficients for the residual stress calculation. An experimental system including real-time measurement, automatic data processing and residual stresses calculation is established. Two applications for non-uniform in-depth residual stress of surface nanocrystalline material and non-uniform in-plane residual stress of friction stir welding are presented. Experimental results show that MIIHD is effective for both non-uniform in-depth and in-plane residual stress measurements.

A Study on the Development of a Robot-Assisted Automatic Laser Hair Removal System

PubMed Central

Lim, Hyoung-woo; Park, Sungwoo; Noh, Seungwoo; Lee, Dong-Hun; Yoon, Chiyul; Koh, Wooseok; Kim, Youdan; Chung, Jin Ho; Kim, Hee Chan

2014-01-01

Abstract Background and Objective: The robot-assisted automatic laser hair removal (LHR) system is developed to automatically detect any arbitrary shape of the desired LHR treatment area and to provide uniform laser irradiation to the designated skin area. Methods: For uniform delivery of laser energy, a unit of a commercial LHR device, a laser distance sensor, and a high-resolution webcam are attached at the six axis industrial robot's end-effector, which can be easily controlled using a graphical user interface (GUI). During the treatment, the system provides real-time treatment progress as well as the total number of “pick and place” automatically. Results: During the test, it was demonstrated that the arbitrary shapes were detected, and that the laser was delivered uniformly. The localization error test and the area-per-spot test produced satisfactory outcome averages of 1.04 mm error and 38.22 mm2/spot, respectively. Conclusions: Results showed that the system successfully demonstrated accuracy and effectiveness. The proposed system is expected to become a promising device in LHR treatment. PMID:25343281

A study on the development of a robot-assisted automatic laser hair removal system.

PubMed

Lim, Hyoung-Woo; Park, Sungwoo; Noh, Seungwoo; Lee, Dong-Hun; Yoon, Chiyul; Koh, Wooseok; Kim, Youdan; Chung, Jin Ho; Kim, Hee Chan; Kim, Sungwan

2014-11-01

Abstract Background and Objective: The robot-assisted automatic laser hair removal (LHR) system is developed to automatically detect any arbitrary shape of the desired LHR treatment area and to provide uniform laser irradiation to the designated skin area. For uniform delivery of laser energy, a unit of a commercial LHR device, a laser distance sensor, and a high-resolution webcam are attached at the six axis industrial robot's end-effector, which can be easily controlled using a graphical user interface (GUI). During the treatment, the system provides real-time treatment progress as well as the total number of "pick and place" automatically. During the test, it was demonstrated that the arbitrary shapes were detected, and that the laser was delivered uniformly. The localization error test and the area-per-spot test produced satisfactory outcome averages of 1.04 mm error and 38.22 mm(2)/spot, respectively. RESULTS showed that the system successfully demonstrated accuracy and effectiveness. The proposed system is expected to become a promising device in LHR treatment.

Spectral characterization of differential group delay in uniform fiber Bragg gratings.

PubMed

Bette, S; Caucheteur, C; Wuilpart, M; Mégret, P; Garcia-Olcina, R; Sales, S; Capmany, J

2005-12-12

In this paper, we completely study the wavelength dependency of differential group delay (DGD) in uniform fiber Bragg gratings (FBG) exhibiting birefringence. An analytical expression of DGD is established. We analyze the impact of grating parameters (physical length, index modulation and apodization profile) on the wavelength dependency of DGD. Experimental results complete the paper. A very good agreement between theory and experience is reported.

Experimental Determination of Unsteady Forces on Contrarotating Propellers for Application to Torpedoes

DTIC Science & Technology

1981-12-01

Experimental determination of Unsteady Forces on Contrarotating Propellers in Uniform Flow ," David Taylor Naval Ship R&D Center, Ship Performance...were planned to determine the unsteady forces on contrarotating propellers in a 4-cycle wake, there were also experiments made in uniform flow to check...Subtitle) S. TYPE OF REPORT G PERIOD COVERED Experimental Determination of Unsteady Forces on

Procedures Manual: A Guide to Uniform Grant and Contract Management Standards and The Common Rule for Uniform Administrative Requirements for Grants and Cooperative Agreements to State and Local Governments.

ERIC Educational Resources Information Center

Conable, Sharon R.

This manual has been compiled to provide consistent grant application and administrative procedures for state agencies which award grants or contracts to local governments. It provides a conceptual framework of information concerning the reporting, financial, contractual, and auditing requirements for recipients of Texas State Library grants…

Approaches to Reducing Federal Spending on Military Health Care

DTIC Science & Technology

2014-01-01

medical school, the Uniformed Services University of the Health Sciences (USUHS), while expanding the number of scholarships provided to students... actuaries esti- 8. Department of Defense, Evaluation of the TRICARE Program— Access, Cost and Quality: Fiscal Year 2013 Report to Congress (February...DoD’s Uniformed Services University of the Health Sciences —would be closed. 4. See Congressional Budget Office, Lessons from Medicare’s Demonstration