Reduced wear of enamel with novel fine and nano-scale leucite glass-ceramics.

PubMed

Theocharopoulos, Antonios; Chen, Xiaohui; Hill, Robert; Cattell, Michael J

2013-06-01

Leucite glass-ceramics used to produce all-ceramic restorations can suffer from brittle fracture and wear the opposing teeth. High strength and fine crystal sized leucite glass-ceramics have recently been reported. The objective of this study is to investigate whether fine and nano-scale leucite glass-ceramics with minimal matrix microcracking are associated with a reduction in in vitro tooth wear. Human molar cusps (n=12) were wear tested using a Bionix-858 testing machine (300,000 simulated masticatory cycles) against experimental fine crystal sized (FS), nano-scale crystal sized (NS) leucite glass-ceramics and a commercial leucite glass-ceramic (Ceramco-3, Dentsply, USA). Wear was imaged using Secondary Electron Imaging (SEI) and quantified using white-light profilometry. Both experimental groups were found to produce significantly (p<0.05) less volume and mean-height tooth loss compared to Ceramco-3. The NS group had significantly (p<0.05) less tooth mean-height loss and less combined (tooth and ceramic) loss than the FS group. Increased waviness and damage was observed on the wear surfaces of the Ceramco-3 glass-ceramic disc/tooth group in comparison to the experimental groups. This was also indicated by higher surface roughness values for the Ceramco-3 glass-ceramic disc/tooth group. Fine and nano-sized leucite glass-ceramics produced a reduction in in vitro tooth wear. The high strength low wear materials of this study may help address the many problems associated with tooth enamel wear and restoration failure. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mean alveolar bone crest height decrement in subjects with an osteoporosis risk

NASA Astrophysics Data System (ADS)

Effrianto, H. P. S.; Priminiarti, M.; Makes, B. N.

2017-08-01

People 40-75 years of age have an osteoporosis risk that may be signaled by a decrease in alveolar bone crest height. Thus, this measure can be used as an indicator of osteoporosis risk. This study was conducted to provide a database of decreased alveolar bone crest heights in ages at risk of osteoporosis by using intraoral radiographs. Forty periapical radiographs of the posterior region of tooth 36 (or 46) were measured twice at different times by two different observers. The interproximal decrease in alveolar bone crest height was measured from the alveolar bone crest to the cementoenamel junction (CEJ) for each tooth on the mesial and distal sides using a ruler (mm). The mean decrease in alveolar bone crest height in at-risk ages for osteoporosis was 3.50±1.085 mm, with a mean of 3.15±0.864 mm for those 45-59 years of age, and 3.90±1.156 mm for those aged 60-75 years. The mean decrease in alveolar bone crest height in people 60-75 years of age was larger than in people 45-59 years of age. There was a medium correlation between age and decreased alveolar bone crest height.

The Association between Primary Tooth Emergence and Anthropometric Measures in Young Adults: Findings from a Large Prospective Cohort Study

PubMed Central

Fatemifar, Ghazaleh; Evans, David M.; Tobias, Jonathan H.

2014-01-01

Cross sectional studies suggest a link may exist between tooth emergence and obesity. To explore this relationship, we aimed to evaluate the prospective associations between primary tooth emergence and anthropometric measures in young adults. Multivariable linear regression was used to analyse relationships between primary tooth emergence, and anthropometric measures measured at 17.8 years, in 2977 participants (1362 males and 1615 females) from the Avon Longitudinal Study of Parents and Children (ALSPAC). In minimally adjusted models, ‘quintiles of number of paired teeth’ (assessed by questionnaire at 15 months) was positively associated with height [change in height (cm) per quintile increase in ‘number of paired teeth’ (β) = 0.35 (95%CI: 0.18, 0.52) P = 0.0001] and weight [ratio of geometric mean weight per quintile increase in ‘number of paired teeth’ (RGM) = 1.015 (95%CI: 1.010, 1.019) P<0.0001]. The relationship with weight was largely driven by fat mass, which showed an equivalent relationship with ‘quintiles of number of paired teeth’ to that seen for weight [RGM = 1.036 (95%CI: 1.022, 1.051) P<0.0001] (adjusted for height)]. Conversely, no association was seen between ‘quintiles of number of paired teeth’ and lean mass. An increase in ‘quintiles of number of paired teeth’ at age 15 months was associated with a higher Tanner stage at age 13 in girls but not boys, but further adjustment of associations between ‘quintiles of number of paired teeth’ and anthropometric traits for Tanner stage was without effect. Primary tooth emergence is associated with subsequent fat mass, suggesting these could share common constitutive factors, and that early primary tooth emergence may represent a hitherto unrecognised risk factor for the development of obesity in later life. PMID:24823714

Predicted Deepwater Bathymetry from Satellite Altimetry: Non-Fourier Transform Alternatives

NASA Astrophysics Data System (ADS)

Salazar, M.; Elmore, P. A.

2017-12-01

Robert Parker (1972) demonstrated the effectiveness of Fourier Transforms (FT) to compute gravitational potential anomalies caused by uneven, non-uniform layers of material. This important calculation relates the gravitational potential anomaly to sea-floor topography. As outlined by Sandwell and Smith (1997), a six-step procedure, utilizing the FT, then demonstrated how satellite altimetry measurements of marine geoid height are inverted into seafloor topography. However, FTs are not local in space and produce Gibb's phenomenon around discontinuities. Seafloor features exhibit spatial locality and features such as seamounts and ridges often have sharp inclines. Initial tests compared the windowed-FT to wavelets in reconstruction of the step and saw-tooth functions and resulted in lower RMS error with fewer coefficients. This investigation, thus, examined the feasibility of utilizing sparser base functions such as the Mexican Hat Wavelet, which is local in space, to first calculate the gravitational potential, and then relate it to sea-floor topography.

Fabrication of long-focal-length plano-convex microlens array by combining the micro-milling and injection molding processes.

PubMed

Chen, Lei; Kirchberg, Stefan; Jiang, Bing-Yan; Xie, Lei; Jia, Yun-Long; Sun, Lei-Lei

2014-11-01

A uniform plano-convex spherical microlens array with a long focal length was fabricated by combining the micromilling and injection molding processes in this work. This paper presents a quantitative study of the injection molding process parameters on the uniformity of the height of the microlenses. The variation of the injection process parameters, i.e., barrel temperature, mold temperature, injection speed, and packing pressure, was found to have a significant effect on the uniformity of the height of the microlenses, especially the barrel temperature. The filling-to-packing switchover point is also critical to the uniformity of the height of the microlenses. The optimal uniformity was achieved when the polymer melts completely filled the mold cavity, or even a little excessively filled the cavity, during the filling stage. In addition, due to the filling resistance, the practical filling-to-packing switchover point can vary with the change of the filling processing conditions and lead to a non-negligible effect on the uniformity of the height of the microlenses. Furthermore, the effect of injection speed on the uniformity of the height of the microlenses was analyzed in detail. The results indicated that the effect of injection speed on the uniformity of the height of the microlenses is mainly attributed to the two functions of injection speed: transferring the filling-to-packing switchover point and affecting the distribution of residual flow stress in the polymer melt.

Quantitative measures of gingival recession and the influence of gender, race, and attrition.

PubMed

Handelman, Chester S; Eltink, Anthony P; BeGole, Ellen

2018-01-29

Gingival recession in dentitions with otherwise healthy periodontium is a common occurrence in adults. Recession is clinically measured using a periodontal probe to the nearest millimeter. The aim of this study is to establish quantitative measures of recession, the clinical crown height, and a new measure the gingival margin-papillae measurement. The latter is seen as the shortest apico-coronal distance measured from the depth of the gingival margin to a line connecting the tips of the two adjacent papillae. Measurements on all teeth up to and including the first molar were performed on pretreatment study models of 120 adult Caucasian and African-American subjects divided into four groups of 30 by gender and race. Both the clinical crown height and the gingival margin-papillae measurements gave a true positive result for changes associated with gingival recession. Tooth wear shortens the clinical crown, and therefore, the measure of clinical crown height can give a false negative result when gingival recession is present. However, the gingival margin-papillae measurement was not affected by tooth wear and gave a true positive result for gingival recession. Tooth wear (attrition) was not associated with an increase in gingival recession. These measures are also useful in detecting recession prior to cemental exposure. Measures for recession and tooth wear were different for the four demographic groups studied. These measures can be used as quantitative standards in both clinical dentistry, research, and epidemiological studies.

Nerve Excitability Properties in Charcot-Marie-Tooth Disease Type 1A

ERIC Educational Resources Information Center

Nodera, Hiroyuki; Bostock, Hugh; Kuwabara, Satoshi; Sakamoto, Takashi; Asanuma, Kotaro; Jia-Ying, Sung; Ogawara, Kazue; Hattori, Naoki; Hirayama, Masaaki; Kaji, Ryuji

2004-01-01

Charcot-Marie-Tooth disease type 1A (CMT1A) is commonly considered a prototype of a hereditary demyelinating polyneuropathy. Apart from the myelin involvement, there has been little information on axonal membrane properties in this condition. Taking advantage of the uniform nature of the disease process, we undertook the "in vivo" assessment of…

Analyses of Deformation and Stress of Oil-free Scroll Compressor Scroll

NASA Astrophysics Data System (ADS)

Peng, Bin; Li, Yaohong; Zhao, Shenxian

2017-12-01

The solid model of orbiting and fixed scroll is created by the Solidworks The deformation and stress of scrolls under gas force, temperature field, inertia force and the coupling field are analyzed using the Ansys software. The deformation for different thickness and height scroll tooth is investigated. The laws of deformation and stress for scrolls are gotten. The research results indicate that the stress and deformation of orbiting scroll are mainly affected by the temperature field. The maximum deformation occurs in the tooth head of scroll wrap because of the largest gas forces and the highest temperature in the tooth head of scroll wrap. The maximum stress is located in the end of the tooth, and the maximum stress of the coupling field is not the sum of loads. The scroll tooth is higher, and the deformation is bigger. The scroll tooth is thicker, and the deformation is smaller.

A clinical correlation between stature and posterior tooth length.

PubMed

Reddy, Smitha; Shome, Bhuvan; Patil, Jayaprakash; Koppolu, Pradeep

2017-01-01

Exploration and determination of the relationship between stature and length of tooth is essential in Paleontology, Forensic Odontology and Endodontology. This study aimed to determine any association between stature and posterior tooth length in a group of patients who required root canal treatment. Age, sex and standing height of adults were considered for posterior tooth length measurement. Molars and Premolars of apparently normal males (n=115 for molars, n= 75 for premolars) and females (n=124 for molars, n=80 for premolars), aged 20-50 years with intact cuspal morphology, which required RCT were selected for this study. Females and males were divided into 2 groups each based on their heights females > 155 cm and ≤ 155 cm, males > 165.10 and ≤ 165.10cm. The tooth length of permanent molars and premolars in both groups were measured using RVG and Electronic apex locator. Measurements obtained were compared separately for males and females using descriptive statistics and Pearson correlation coefficient. In females MB, ML, D roots of molar showed significant association (P=0.021), (P=0.027), (P=0.010) and roots of premolars showed significant association (P=0.002), (P=0.006) between both the groups respectively In males MB, ML, D roots of molar showed significant association (P=0.009), (P=0.004), (P=0.015) and roots of premolars showed significant association (P=0.006), (P=0.020) between both the groups respectively. The present clinical study reveals that there is a positive association between stature and posterior tooth length in both males and females.

Maxillary anterior en masse retraction using different antero-posterior position of mini screw: a 3D finite element study.

PubMed

Hedayati, Zohreh; Shomali, Mehrdad

2016-12-01

Nowadays, mini screws are used in orthodontic tooth movement to obtain maximum or absolute anchorage. They have gained popularity among orthodontists for en masse retraction of anterior teeth after first premolar extraction in maximum anchorage cases. The purpose of this study was to determine the type of anterior tooth movement during the time when force was applied from different mini screw placements to the anterior power arm with various heights. A finite element method was used for modeling maxillary teeth and bone structure. Brackets, wire, and hooks were also designed for modeling. Two appropriate positions for mini screw in the mesial and distal of the second premolar were designed as fixed nodes. Forces were applied from the mini screw to four different levels of anterior hook height: 0, 3, 6, and 9 mm. Initial tooth movement in eight different conditions was analyzed and calculated with ANSYS software. Rotation of anterior dentition was decreased with a longer anterior power arm and the mesial placement of the mini screw. Bodily movements occurred with the 9-mm height of the power arm in both mini screw positions. Intrusion or extrusion of the anterior teeth segment depended on the level of the mini screw and the edge of the power arm on the Z axis. According to the findings of this study, the best control in the sagittal plane during anterior en masse retraction was achieved by mesial placement of the mini screw and the 9-mm height of the anterior power arm. Where control in the vertical plane was concerned, distal placement of the mini screw with the 6-mm power arm height had minimum adverse effect on anterior dentition.

Developmental Disturbances of a Maxillary Central Incisor due to Trauma to Its Predecessor: A Case Report

PubMed Central

Karataş, Merve Safa; Sönmez, Işıl Şaroğlu

2013-01-01

Objective To report the effects of a primary tooth trauma on the underlying permanent tooth germ. Clinical Presentation and Intervention A 12-year-old girl was referred to our clinic with a complaint of poor aesthetic appearance. The crown of the permanent maxillary left central tooth exhibited an increased clinical crown height with an ‘enamel hyperplasia’ in the cervical third and had hypoplastic enamel with yellowish-brown discoloration extending from the middle third to the incisal edge. Radiographic examination revealed that the permanent maxillary left central tooth had abnormal root morphology with root dilaceration. The patient revealed a history of trauma at the age of 4 years. An aesthetic restoration with light-curing resin composite was performed on the vestibular surface of the maxillary left permanent central tooth. Conclusion Sequelae of a primary tooth trauma on the permanent tooth were restored. We recommend that parents should be aware of the consequences of untreated trauma to a primary tooth. Educational and preventive programmes on dental trauma are required to educate parents about emergency knowledge and sequelae of dental trauma. PMID:23689528

Pulp/tooth ratio of mandibular first and second molars on panoramic radiographs: An aid for forensic age estimation

PubMed Central

Shah, Palak H.; Venkatesh, Rashmi

2016-01-01

Objective: To determine and compare the accuracy of pulp/tooth ratio method in mandibular first and second molar teeth in forensic age estimation. Materials and Methods: A total 300 panoramic radiographs of the Gujarati population (187 males and 113 females) were studied. The measurements of Pulp Chamber Height (PCH) and Crown Root Trunk Height (CRTH) were performed on the mandibular first and second molar teeth. The acquired data was subjected to correlation and regression. Results: The pulp chamber crown root trunk height ratios (PCTHR) of both the first (r = −0.609) and second molars (r = −0.422) were significantly correlated with the age of the individual. Individual regression formulae were derived for both the teeth which were then used separately to calculate the age. The standard errors estimate (SEE) for the first and second molars were 8.84 years and 10.11 years, respectively. There was no statistically significant difference between chronological and calculated age by both the teeth (P = 1.000). Conclusion: The mandibular first and second molar is a potential tool for age estimation in forensic dentistry. The pulp/tooth ratio of both the teeth is a useful method for forensic age prediction with reasonable accuracy in the Gujarati population. PMID:27555734

Development of a Remodeled Caspar Retractor and Its Application in the Measurement of Distractive Resistance in an In Vitro Anterior Cervical Distraction Model.

PubMed

Wen, Junxiang; Xu, Jianwei; Li, Lijun; Yang, Mingjie; Pan, Jie; Chen, Deyu; Jia, Lianshun; Tan, Jun

2017-06-01

In vitro biomechanical study of the cervical intervertebral distraction using a remodeled Caspar retractor. To investigate the torques required for distraction to different heights in an in vitro C3-C4 anterior cervical distraction model using a remodeled Caspar retractor, focusing on the influence of the intervertebral disk, posterior longitudinal ligament (PLL), and ligamentum flavum (LF). No previous studies have reported on the torques required for distraction to various heights or the factors resisting distraction in anterior cervical discectomy and fusion. Anterior cervical distractions at C3-C4 was performed in 6 cadaveric specimens using a remodeled Caspar retractor, under 4 conditions: A, before disk removal; B, after disk removal; C, after disk and PLL removal; and D, after disk and PLL removal and cutting of the LF. Distraction was performed for 5 teeth, and distractive torque of each tooth was recorded. The torque increased with distraction height under all conditions. There was a sudden increase in torque at the fourth tooth under conditions B and C, but not D. Under condition A, distraction to the third tooth required 84.8±13.3 cN m. Under conditions B and C, distraction to the third tooth required <13 cN m, and further distraction required dramatically increased torque. Under condition D, no marked increase in torque was recorded. Distraction of the intervertebral space was much easier after disk removal. An intact LF caused a sudden marked increase in the force required for distraction, possibly indicating the point at which the LF was fully stretched. This increase in resistance may help to determine the optimal distraction height to avoid excessive stress to the endplate spacer. The remodeled Caspar retractor in the present study may provide a feasible and convenient method for intraoperative measurement of distractive resistance.

[Oral Anatomy.

PubMed

Abe, Shinichi

With regard to oral cavity, it is known that jaw bone morphology greatly changes with tooth loss. Therefore, it is necessary to consider the muscles attached to the jaw bone and the surrounding vessels and nerves, in connection with the jaw bone morphology after tooth loss. As an example, the height of the mandibular bone decreases to the position of the mylohyoid line after tooth loss. By this marked morphological change in the alveolar area, the lingual nerve and the lingual artery branches running in the sublingual area on the mandibular inner surface becomes located in the area almost the same as the alveolar crest.

On the evolutionary advantage of multi-cusped teeth

PubMed Central

Bush, Mark B.; Barani, Amir; Lawn, Brian R.

2016-01-01

A hallmark of mammalian evolution is a progressive complexity in postcanine tooth morphology. However, the driving force for this complexity remains unclear: whether to expand the versatility in diet source, or to bolster tooth structural integrity. In this study, we take a quantitative approach to this question by examining the roles of number, position and height of multiple cusps in determining sustainable bite forces. Our approach is to use an extended finite-element methodology with due provision for step-by-step growth of an embedded crack to determine how fracture progresses with increasing occlusal load. We argue that multi-cusp postcanine teeth are well configured to withstand high bite forces provided that multiple cusps are contacted simultaneously to share the load. However, contact on a single near-wall cusp diminishes the strength. Location of the load points and cusp height, rather than cusp number or radius, are principal governing factors. Given these findings, we conclude that while complex tooth structures can enhance durability, increases in cusp number are more likely to be driven by the demands of food manipulation. Structural integrity of complex teeth is maintained when individual cusps remain sufficiently distant from the side walls and do not become excessively tall relative to tooth width. PMID:27558851

Clinical use of the resorbable bioscaffold poly lactic co-glycolic acid (PLGA) in post-extraction socket for maintaining the alveolar height: A prospective study.

PubMed

Hoda, Nadeemul; Saifi, Aamir Malick; Giraddi, Girish B

2016-01-01

A common sequel of tooth extraction is alveolar bone resorption. It makes the placement of dental implants difficult and creates an esthetic problem for the fabrication of conventional prostheses. Therefore, alveolar bone following tooth extraction should be preserved. The present prospective study was conducted to evaluate the efficacy of the resorbable bioscaffold poly lactic co-glycolic acid (PLGA) in maintaining the alveolar height in post-extraction socket. 20 patients were selected based on inclusion and exclusion criteria and were randomly divided into two groups: cases and control comprising of 10 patients each. Atraumatic tooth extraction was done in all patients. PLGA bioscaffold was placed in cases and socket was closed with 3-0 vicryl. In control group, socket was directly closed with 3-0 vicryl. The patients were kept on follow-up and complications such as dry socket, pain, and swelling were recorded. IOPA were taken at 1st, 4th, 12th, and 24th week to record changes in the height of alveolar bone. The radiographic measurements were compared and the differences were statistically analyzed. Reduction in alveolar bone height after placement of PLGA bioscaffold was significantly less in cases as compared to controls at 4th, 12th, and 24th week following extraction. No complications were observed throughout the follow-up period. PLGA scaffold significantly reduces bone resorption. Application is very simple and can be easily performed in a dental setup. However, PLGA scaffold adds significantly to the cost of treatment.

Gear Crack Propagation Path Studies: Guidelines for Ultra-Safe Design

NASA Technical Reports Server (NTRS)

Lewicki, David G.

2001-01-01

Design guidelines have been established to prevent catastrophic rim fracture failure modes when considering gear tooth bending fatigue. Analysis was performed using the finite element method with principles of linear elastic fracture mechanics. Crack propagation paths were predicted for a variety of gear tooth and rim configurations. The effects of rim and web thicknesses, initial crack locations, and gear tooth geometry factors such as diametral pitch, number of teeth, pitch radius, and tooth pressure angle were considered. Design maps of tooth/rim fracture modes including effects of gear geometry, applied load, crack size, and material properties were developed. The occurrence of rim fractures significantly increased as the backup ratio (rim thickness divided by tooth height) decreased. The occurrence of rim fractures also increased as the initial crack location was moved down the root of the tooth. Increased rim and web compliance increased the occurrence of rim fractures. For gears with constant pitch radii, coarser-pitch teeth increased the occurrence of tooth fractures over rim fractures. Also, 25 deg pressure angle teeth had an increased occurrence of tooth fractures over rim fractures when compared to 20 deg pressure angle teeth. For gears with constant number of teeth or gears with constant diametral pitch, varying size had little or no effect on crack propagation paths.

Orthodontics for the dog. Treatment methods.

PubMed

Ross, D L

1986-09-01

This article considers the prevention of orthodontic problems, occlusal adjustments, simple tooth movements, rotational techniques, tipping problems, adjustment of crown height, descriptions of common orthodontic appliances, and problems associated with therapy.

Analysis of the golden proportion and width/height ratios of maxillary anterior dentition in patients with lateral incisor agenesis.

PubMed

Pini, Núbia Pavesi; de-Marchi, Luciana Manzotti; Gribel, Bruno Frazão; Ubaldini, Adriana Lemos Mori; Pascotto, Renata Corrêa

2012-12-01

  The purpose of this study was to assess the presence of the golden proportion (GP) in the facial view tooth-to-tooth width proportion of the six maxillary anterior teeth and to evaluate the width/height (W/H) ratios of the incisors of patients with maxillary lateral incisor (LI) agenesis treated either with implants or orthodontically (by moving canines into the position of the laterals, recontouring them, and placing composite restorations over the repositioned teeth).   Forty-eight patients with LI agenesis were divided into four experimental groups: unilateral recontouring group (N = 10), bilateral recontouring group (BRG, N = 18), unilateral implant group (UIG, N = 10), bilateral implant group (N = 10), and a control group (CG, N = 25) of patients without agenesis. GP ratios were determined on patients' dental casts placed over Levin's grids, whereas W/H ratios were measured directly on the casts and a millimeter ruler to determine these distances. Statistical analysis was performed with Shapiro-Wilk, Kruskal-Wallis, Mann-Whitney, Friedman, and Wilcoxon tests (p < 0.05).   The incidence of GP in the tooth-to-tooth width proportions was significantly different between groups and more commonly found between centrals and laterals than between laterals and canines. The GP was more likely to be observed in the BRG, UIG, and CG. The results demonstrated that the GP was not found to be present in the majority of the cases treated with maxillary agenesis, regardless of the method of treatment. The mean W/H ratios of the laterals ranged between 0.75 and 0.90.   Although the GP may be a useful diagnostic guide, it was not observed in the majority of esthetic outcomes of patients treated with maxillary LI agenesis in this study. The assessment of the golden proportion and width/height ratio of upper anterior teeth in patients with upper lateral incisor agenesis treated with either implants or tooth re-contouring may assist dentists and patients in deciding the best treatment option based on the peculiarities of each case. © 2012 Wiley Periodicals, Inc.

[Measurement and analysis of smile line of 62 Han-Chinese].

PubMed

Hu, Xiu-lian; Heberer, Susanne; Nelson, Katja; Lin, Ye

2011-11-01

To analyze smile features in maximum lip-dynamic in Chinese. Sixty-two Han-Chinese, travelling in Germany, with a mean age of 28.5 years were enrolled and photographed. Standardized digital photos were made to measure the height of displayed maxillary gingiva, papilla and tooth during an enjoyment smile. Statistical analysis was performed using Mann-Whitney-U Test and non-parametric analysis. The mean height of tooth display for the central incisors was 10 mm, with no significant difference between the gender (P > 0.05). The mean height of gingival display was 1.3 mm and the mean papilla height was 3.4 mm. There was no significant difference between the genders (P > 0.05). 31% (19/62) of the subjects belonged to high smile line type, 50% (31/62) to medium smile line type and 19% (12/62) to low smile line type. The red esthetics is a paramount factor for Chinese men and women in the esthetic restoration. 81% of the Chinese studied showed various degree of gingival exposure from central incisor to the premolars, which defined the esthetic area for Chinese people. Papilla is a critical parameter for esthetic evaluation and treatment design. The ratio of high smile line in Chinese may be higher than that in Caucasian.

Assessing the effects of tooth loss in adult crania using geometric morphometrics.

PubMed

Small, Candice; Brits, Desiré; Hemingway, Jason

2016-01-01

With high numbers of unidentified skeletonised remains recovered annually in South Africa and an increased number of edentate individuals being reported, the question arises as to whether tooth loss would result in craniofacial changes which might alter the accuracy of osteological analyses. Forty-five fixed landmarks together with sliding semilandmarks were collected from 229 white South African crania and were used to capture curve data pertaining to the basicranium, alveoli, zygomatic arches, nasal aperture and orbits. Geometric morphometric methods were employed to assess the effects of tooth loss on these structures. Although a number of effects were seen when the skull was analysed in its entirety, only the alveoli proved to be significantly affected when regions were analysed individually. Both upper facial height and palate shape were affected by tooth loss, which may influence various osteometric measurements and qualitative traits that are used during the assessment of ancestry and sex.

Smile line assessment comparing quantitative measurement and visual estimation.

PubMed

Van der Geld, Pieter; Oosterveld, Paul; Schols, Jan; Kuijpers-Jagtman, Anne Marie

2011-02-01

Esthetic analysis of dynamic functions such as spontaneous smiling is feasible by using digital videography and computer measurement for lip line height and tooth display. Because quantitative measurements are time-consuming, digital videography and semiquantitative (visual) estimation according to a standard categorization are more practical for regular diagnostics. Our objective in this study was to compare 2 semiquantitative methods with quantitative measurements for reliability and agreement. The faces of 122 male participants were individually registered by using digital videography. Spontaneous and posed smiles were captured. On the records, maxillary lip line heights and tooth display were digitally measured on each tooth and also visually estimated according to 3-grade and 4-grade scales. Two raters were involved. An error analysis was performed. Reliability was established with kappa statistics. Interexaminer and intraexaminer reliability values were high, with median kappa values from 0.79 to 0.88. Agreement of the 3-grade scale estimation with quantitative measurement showed higher median kappa values (0.76) than the 4-grade scale estimation (0.66). Differentiating high and gummy smile lines (4-grade scale) resulted in greater inaccuracies. The estimation of a high, average, or low smile line for each tooth showed high reliability close to quantitative measurements. Smile line analysis can be performed reliably with a 3-grade scale (visual) semiquantitative estimation. For a more comprehensive diagnosis, additional measuring is proposed, especially in patients with disproportional gingival display. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Longevity of Single-Tooth All-Ceramic CAD/CAM Restorations: A Meta-Analysis

DTIC Science & Technology

2013-07-01

A thesis submitted to the Faculty of the Comprehensive Dentistry Graduate Program Naval Postgraduate Dental School Uniformed Services...Naval Postgraduate Dental School Uniformed Services University of the Health Sciences Bethesda, Maryland CERTIFICATE OF APPROVAL MASTER’S THESIS...This is to certify that the Master’s thesis of Katherine L. Cheng Lieutenant, Dental Corps, U.S. Navy has been approved by the Examining Committee for

Design improvement of a pump wear ring labyrinth seal

NASA Technical Reports Server (NTRS)

Rhode, David L.; Morrison, G. L.; Ko, S. H.; Waughtal, S. P.

1987-01-01

The investigation was successful in obtaining two improved designs for the impeller wear ring seal of the liquid hydrogen turbopump of interest. A finite difference computer code was extensively used in a parametric computational study in determining a cavity configuration with high flow resistance due to turbulence dissipation. These two designs, along with that currently used, were fabricated and tested. The improved designs were denoted Type O and Type S. The measurements showed that Type O and Type S given 67 and 30 percent reduction in leakage over the current design, respectively. It was found that the number of cavities, the step height and the presence of a small stator groove are quite important design features. Also, the tooth thickness is of some significance. Finally, the tooth height and an additional large cavity cut out from the stator (upstream of the step) are of negligible importance.

Changes in the transmission properties of multi-tooth plasmonic nano-filters (multi-TPNFs) caused by geometrical imperfection

NASA Astrophysics Data System (ADS)

Khaksar, A.; Fatemi, H.

2012-08-01

To model the filtering behavior of a multi-tooth plasmonic nano-filter (multi-TPNF), an equivalent circuitry composed of a set of serried impedances is considered. The changes caused in its filtering behavior are proposed as a measuring tool to investigate the effect of the geometrical imperfections occurring during the manufacture of the device. Consequently, the effects of changes in the nominal size of each of the geometrical parameters of a multi-TPNF sample, such as its tooth height, d, its tooth width, w, and the separation between two successive teeth, Δ, on its transmittance are investigated. It is observed that each single tooth of the multi-TPNF and also the waveguide between any of its two successive teeth exhibit a very Fabry-Perot interferometer like behavior. The variation of the transmission spectra of a multi-TPNF whose geometrical parameters are imperfect is compared with the desired filter, and also the effect of the number of geometrically imperfect teeth of the multi-TPNF on the filtering spectra is examined.

Effect of Speed (Centrifugal Load) on Gear Crack Propagation Direction

NASA Technical Reports Server (NTRS)

Lewicki, David G.

2001-01-01

The effect of rotational speed (centrifugal force) on gear crack propagation direction was explored. Gears were analyzed using finite element analysis and linear elastic fracture mechanics. The analysis was validated with crack propagation experiments performed in a spur gear fatigue rig. The effects of speed, rim thickness, and initial crack location on gear crack propagation direction were investigated. Crack paths from the finite element method correlated well with those deduced from gear experiments. For the test gear with a backup ratio (rim thickness divided by tooth height) of nib = 0.5, cracks initiating in the tooth fillet propagated to rim fractures when run at a speed of 10,000 rpm and became tooth fractures for speeds slower than 10,000 rpm for both the experiments and anal sis. From additional analysis, speed had little effect on crack propagation direction except when initial crack locations were near the tooth/rim fracture transition point for a given backup ratio. When at that point, higher speeds tended to promote rim fracture while lower speeds (or neglecting centrifugal force) produced tooth fractures.

Determination of orthodontic tooth movement and tissue reaction following demineralized freeze-dried bone allograft grafting intervention

PubMed Central

Seifi, Massoud; Ghoraishian, Seyed Ahmad

2012-01-01

Background: Socket preservation after tooth extraction is one of the indications of bone grafting to enhance preorthodontic condition. The aim of this study is to determine the effects of socket preservation on the immediate tooth movement, alveolar ridge height preservation and orthodontic root resorption. Materials and Methods: In a split-mouth technique, twelve sites in three dogs were investigated as an experimental study. Crushed demineralized freeze-dried bone allograft (DFDBA) (CenoBone®) was used as the graft material. The defects were made by the extraction of 3rd premolar. On one side of each jaw, the defects were preserved by DFDBA and defects of the other side left opened as the control group. Simultaneously the teeth adjacent to the defects were pulled together by a NiTi coil spring. After eight weeks, the amount of (OTM), alveolar height, and root resorption were measured. Analysis of variance was used for purpose of comparison. Results: There was a slight increase in OTM at grafted sites as they were compared to the control sites (P<0.05). Also a significant bone resorption in control site and successful socket preservation in experimental site were observed. Reduction of root resorption at the augmented site was significant compared to the normal healing site (P<0.05). Conclusion: Using socket preservation, tooth movement can be immediately started without waiting for the healing of the recipient site. This can provide some advantages like enhanced rate of OTM, its approved effects on ridge preservation that reduces the chance of dehiscence and the reduction of root resorption. PMID:22623939

Contour changes in human alveolar bone following tooth extraction of the maxillary central incisor.

PubMed

Li, Bei; Wang, Yao

2014-12-01

The purpose of this study was to apply cone-beam computed tomography (CBCT) to observe contour changes in human alveolar bone after tooth extraction of the maxillary central incisor and to provide original morphological evidence for aesthetic implant treatment in the maxillary anterior area. Forty patients were recruited into the study. Each patient had two CBCT scans (CBCT I and CBCT II), one taken before and one taken three months after tooth extraction of maxillary central incisor (test tooth T). A fixed anatomic reference point was used to orient the starting axial slice of the two scans. On three CBCT I axial slices, which represented the deep, middle, and shallow layers of the socket, labial and palatal alveolar bone widths of T were measured. The number of sagittal slices from the start point to the pulp centre of T was recorded. On three CBCT II axial slices, the pulp centres of extracted T were oriented according to the number of moved sagittal slices recorded in CBCT I. Labial and palatal alveolar bone widths at the oriented sites were measured. On the CBCT I axial slice which represented the middle layer of the socket, sagittal slices were reconstructed. Relevant distances of T on the sagittal slice were measured, as were the alveolar bone width and tooth length of the opposite central incisor. On the CBCT II axial slice, which represented the middle layer of the socket, relevant distances recorded in CBCT I were transferred on the sagittal slice. The height reduction of alveolar bone on labial and palatal sides was measured, as were the alveolar bone width and tooth length of the opposite central incisor at the oriented site. Intraobserver reliability assessed by intraclass correlation coefficients (ICCs) was high. Paired sample t-tests were performed. The alveolar bone width and tooth length of the opposite central incisor showed no statistical differences (P<0.05). The labial alveolar bone widths of T at the deep, middle, and shallow layers all showed statistical differences. However, no palatal alveolar bone widths showed any statistical differences. The width reduction of alveolar bone was 1.2, 1.6, and 2.7 mm at the deep, middle, and shallow layers, respectively. The height reduction of alveolar bone on labial and palatal sides of T both showed statistical differences, which was 1.9 and 1.1 mm, respectively.

Benefits of Two Turbine Rotor Diameters and Hub Heights in the Same Wind Farm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dykes, Katherine L; Stanley, Andrew P. J.; Ning, Andrew

Significant turbine-wake interactions greatly reduce power output in a wind farm. If different turbine hub heights and rotor diameters are included in the same wind farm, the wake interference in the farm will be reduced, resulting in a lower cost of energy (COE) than a farm with identical turbines. In this paper, we present a method to model wind farm COE in farms with hub heights and rotor diameters that vary across the wind farm. We also demonstrate how to optimize these wind farms to minimize COE. The results show that COE can be greatly reduced in wind farms withmore » non-homogeneous turbines, especially when the turbines are spaced close together. For a unidirectional wind rose, including different turbine design in the wind farm has a similar decrease in COE to spreading the wind turbines farther apart. When the rotor diameter and hub height of the wind turbines in a farm are optimized uniformly, a COE decrease of 4% to 13% (depending on the grid spacing and wind shear exponent) is achieved compared to the baseline. When the rotor diameter and turbine heights are optimized non-uniformly, with two different diameters and heights throughout the farm, there is a COE decrease of 22% to 41% compared to the baseline. For a more spread wind rose with a dominant probability from the west, there is a COE decrease between 3% and 10% for uniformly optimized rotor diameter and height compared to the baseline. With two optimized rotor diameters and heights through the farm, a COE decrease of 3% to 19% is achieved. For a similar wind rose shifted such that the dominant wind direction is from the northwest, a COE decrease between 3% and 10% results from uniformly optimized wind turbines compared to the baseline. A COE decrease of 3% to 17% compared to the baseline occurs with two different turbines are optimized throughout the wind farm.« less

Highly uniform residual layers for arrays of 3D nanoimprinted cavities in Fabry-Pérot-filter-array-based nanospectrometers

NASA Astrophysics Data System (ADS)

Memon, Imran; Shen, Yannan; Khan, Abdullah; Woidt, Carsten; Hillmer, Hartmut

2016-04-01

Miniaturized optical spectrometers can be implemented by an array of Fabry-Pérot (FP) filters. FP filters are composed of two highly reflecting parallel mirrors and a resonance cavity. Each filter transmits a small spectral band (filter line) depending on its individual cavity height. The optical nanospectrometer, a miniaturized FP-based spectrometer, implements 3D NanoImprint technology for the fabrication of multiple FP filter cavities in a single process step. However, it is challenging to avoid the dependency of residual layer (RL) thickness on the shape of the printed patterns in NanoImprint. Since in a nanospectrometer the filter cavities vary in height between neighboring FP filters and, thus, the volume of each cavity varies causing that the RL varies slightly or noticeably between different filters. This is one of the few disadvantages of NanoImprint using soft templates such as substrate conformal imprint lithography which is used in this paper. The advantages of large area soft templates can be revealed substantially if the problem of laterally inhomogeneous RLs can be avoided or reduced considerably. In the case of the nanospectrometer, non-uniform RLs lead to random variations in the designed cavity heights resulting in the shift of desired filter lines. To achieve highly uniform RLs, we report a volume-equalized template design with the lateral distribution of 64 different cavity heights into several units with each unit comprising four cavity heights. The average volume of each unit is kept constant to obtain uniform filling of imprint material per unit area. The imprint results, based on the volume-equalized template, demonstrate highly uniform RLs of 110 nm thickness.

Impact of roof height non-uniformity on pollutant transport between a street canyon and intersections.

PubMed

Nosek, Štěpán; Kukačka, Libor; Jurčáková, Klára; Kellnerová, Radka; Jaňour, Zbyněk

2017-08-01

This paper presents an extension of our previous wind-tunnel study (Nosek et al., 2016) in which we highlighted the need for investigation of the removal mechanisms of traffic pollution from all openings of a 3D street canyon. The extension represents the pollution flux (turbulent and advective) measurements at the lateral openings of three different 3D street canyons for the winds perpendicular and oblique to the along-canyon axis. The pollution was simulated by emitting a passive gas (ethane) from a homogeneous ground-level line source positioned along the centreline of the investigated street canyons. The street canyons were formed by courtyard-type buildings of two different regular urban-array models. The first model has a uniform building roof height, while the second model has a non-uniform roof height along each building's wall. The mean flow and concentration fields at the canyons' lateral openings confirm the findings of other studies that the buildings' roof-height variability at the intersections plays an important role in the dispersion of the traffic pollutants within the canyons. For the perpendicular wind, the non-uniform roof-height canyon appreciably removes or entrains the pollutant through its lateral openings, contrary to the uniform canyon, where the pollutant was removed primarily through the top. The analysis of the turbulent mass transport revealed that the coherent flow structures of the lateral momentum transport correlate with the ventilation processes at the lateral openings of all studied canyons. These flow structures coincide at the same areas and hence simultaneously transport the pollutant in opposite directions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Prosthetic treatment of oligodontia with a tooth-supported overdenture--a case report.

PubMed

Akeredolu, P A

2002-01-01

An unusual case of oligodontia is reported in a 20 year old Nigerian male. It is unusual because of the isolated occurrence of the oligodontia which is unassociated with a family history or any other clinical features suggestive of specific syndromes or severe systemic abnormality. The patient presented with conically or peg shaped anterior and malformed posterior teeth in both the maxilla and mandible. Full mouth periapical radiographs revealed stunted roots, widening of the periodontal space and an unerupted tooth in the right mandibular premolar region. Tooth-supported upper and lower removable partial overdenture were fabricated for him. This modality of treatment is a better choice which helps not only to preserve the alveolar ridge height and improve aesthetics, but also preserves the proprioceptive mechanisms associated with the periodontal membrane of natural teeth.

Increasing the amount of corticotomy does not affect orthodontic tooth movement or root resorption, but accelerates alveolar bone resorption in rats.

PubMed

Kurohama, Takeshi; Hotokezaka, Hitoshi; Hashimoto, Megumi; Tajima, Takako; Arita, Kotaro; Kondo, Takanobu; Ino, Airi; Yoshida, Noriaki

2017-06-01

The purpose of this study was to evaluate the relationships among the volume of bone cut during corticotomy, amount of tooth movement, volume of root resorption, and volume of the resultant alveolar bone resorption after tooth movement. Ten-week-old female Wistar rats were distributed into the corticotomy groups and a control group that underwent sham corticotomy. Two experiments employing two different orthodontic forces (10 or 25g) and experimental periods (14 or 21 days) were performed. The volumes of the bone cut by corticotomy were 0.1, 1.0, and 1.7mm3 in the 25g groups, and 1.0 and 1.7mm3 in the 10g groups. Nickel-titanium closed-coil springs were set on the maxillary left first molars to induce mesial movement. After orthodontic tooth movement, the amount of tooth movement, volume of root resorption, and volume of alveolar bone resorption were measured. Despite differences in the volume of bone cut among the different corticotomy groups, there were not significant differences in the amount of tooth movement and volume of root resorption between the control group and any of the corticotomy groups. However, higher volume of bone cut during corticotomy was significantly related to the decreased alveolar bone volume-in particular, to the reduced height of the alveolar bone crest after tooth movement. The volume of the alveolar bone cut during corticotomy does not affect tooth movement or root resorption in 10-week-old female Wistar rats; however, it may increase alveolar bone loss after tooth movement. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

[Three dimensional finite element analysis of maxillary anterior teeth retraction with micro-implant anchorage and sliding mechanics].

PubMed

Zhang, Yi; Zhang, Lei; Fan, Yu-bo; Song, Jin-lin; Deng, Feng

2009-10-01

To investigate the biomechanical effects of micro-implant anchorage technique with sliding mechanics on maxillary anterior teeth retraction under different implant insertion heights and different retraction hook heights. The three dimensional finite element model of maxillary anterior teeth retraction force system was constructed with CT scanning and MIMICS software and the relationships between brackets, teeth, wire and micro-implant were simulating the clinical factions. Then the initial tooth displacement was calculated when the insertion heights were 4 mm and 8 mm and the retraction hook heights were 1, 4, 7, 10 mm respectively. With retraction hook height added, the anterior teeth movement changed from lingual crown tipping to labial crown tipping and the intrusion movement was more apparent when the micro-implant was inserted in a higher location. The ideal teeth movement control could be achieved by different insertion heights of micro-implant and different retraction hook heights in straight wire retraction force system.

Human pulpal blood flow in different root formation stages measured with transmitted-light plethysmography.

PubMed

Ganbold, Khongorzul; Kakino, Satoko; Ikeda, Hideharu; Miyashin, Michiyo

2017-11-01

To determine the pulp vitality after traumatic injury, dentists often use pulp sensitivity tests, which can be ambiguous in young permanent teeth with incomplete root formation. Transmitted-light plethysmography (TLP) is a non-invasive objective method that uses a 525-nm LED to detect blood volume change in the pulp. The present study aimed (1) to investigate pulpal blood flow with TLP and optical characteristics in healthy permanent maxillary incisors in different root formation stages, and (2) to assess the influences of body growth of the children and tooth color on the TLP amplitude. Seventy-eight fully erupted maxillary central incisors were divided into four groups, according to the root formation stages. Group 1: root with wide-open apex, Group 2: root completed in length with open apex, Group 3: root with half-closed apex, Group 4: root with complete formation. The TLP amplitude, optical density, electric pulp testing, and cervical tooth color measurements of each group were compared using a one-way analysis of variance followed by the Bonferroni method. The correlation between the weights/heights of children and TLP amplitudes was analyzed using Pearson coefficient. The TLP amplitude was significantly higher in Group 3 than in the other groups. The amplitude was correlated with the weights/heights of children, but not with the tooth color. Optical density and electric sensitivity increased with tooth maturation. The amplitude of TLP and optical density may be affected by growth and development in children and indicate changes in the vascular dynamics of the pulp and hard tissue maturation during root formation stages. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gear Crack Propagation Path Studies-- Guidelines Developed for Ultrasafe Design

NASA Technical Reports Server (NTRS)

Lewicki, David G.

2002-01-01

Effective gear designs balance strength, durability, reliability, size, weight, and cost. However, unexpected gear failures may occur even with adequate gear tooth design. To design an extremely safe system, the designer must ask and address the question "What happens when a failure occurs?" With regard to gear-tooth bending fatigue, tooth or rim fractures may occur. For aircraft, a crack that propagated through a rim would be catastrophic, leading to the disengagement of a rotor or propeller, the loss of an aircraft, and possible fatalities. This failure mode should be avoided. However, a crack that propagated through a tooth might or might not be catastrophic, depending on the design and operating conditions. Also, early warning of this failure mode might be possible because of advances in modern diagnostic systems. An analysis was performed at the NASA Glenn Research Center to develop design guidelines to prevent catastrophic rim fracture failure modes in the event of gear-tooth bending fatigue. The finite element method was used with principles of linear elastic fracture mechanics. Crack propagation paths were predicted for a variety of gear tooth and rim configurations. The effects of rim and web thicknesses, initial crack locations, and gear-tooth geometry factors such as diametral pitch, number of teeth, pitch radius, and tooth pressure angle were considered. Design maps of tooth and rim fracture modes, including the effects of gear geometry, applied load, crack size, and material properties were developed. The occurrence of rim fractures significantly increased as the backup ratio (rim thickness divided by tooth height) decreased. The occurrence of rim fractures also increased as the initial crack location was moved down the root of the tooth. Increased rim and web compliance increased the occurrence of rim fractures. For gears with constant-pitch radii, coarser-pitch teeth increased the occurrence of tooth fractures over rim fractures. Also, 25 degree pressure angle teeth increased the occurrence of tooth fractures over rim fractures in comparison to 20 pressure angle teeth. For gears with a constant number of teeth or for gears with constant diametral pitch, varying size had little or no effect on crack propagation paths.

Numerical simulation of operation modes in atmospheric pressure uniform barrier discharge excited by a saw-tooth voltage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li Xuechen; Niu Dongying; Yin Zengqian

2012-08-15

The characteristics of dielectric barrier discharge excited by a saw-tooth voltage are simulated in atmospheric pressure helium based on a one-dimensional fluid model. A stepped discharge is obtained per half voltage cycle with gas gap width less than 2 mm by the simulation, which is different to the pulsed discharge excited by a sinusoidal voltage. For the stepped discharge, the plateau duration increases with increasing the voltage amplitude and decreasing the gas gap. Therefore, uniform discharge with high temporal duty ratio can be realized with small gap through increasing the voltage amplitude. The maximal densities of both electron and ionmore » appear near the anode and the electric field is almost uniformly distributed along the gap, which indicates that the stepped discharge belongs to a Townsend mode. In contrast to the stepped discharge with small gas gap, a pulsed discharge can be obtained with large gas gap. Through analyzing the spatial density distributions of electron and ion and the electric field, the pulsed discharge is in a glow mode. The voltage-current (V-I) characteristics are analyzed for the above mentioned discharges under different gas gaps, from which the different discharge modes are verified.« less

Bicuspid Axial Wall Height Effect on CAD/CAM Crown Fracture Mode on Preparations Containing Advanced Total Occlusal Convergence.

PubMed

Miller, Matthew; DuVall, Nicholas; Brewster, John; Wajdowicz, Michael N; Harris, Ashley; Roberts, Howard W

2018-02-18

To evaluate bicuspid axial wall height effect on the fracture mode of adhesively luted, all-ceramic CAD/CAM crowns with a 20° total occlusal convergence (TOC). Recently extracted premolars were randomly divided into 4 groups (n = 12) with all-ceramic crown preparations accomplished using a high-speed handpiece inserted into a milling device. Specimens were prepared containing occlusogingival axial wall heights of 3, 2, and 1 mm as well as a group containing a flat preparation surface with no axial wall height. All preparations contained a 20° TOC. Completed preparation surface area was determined, and preparation features confirmed using a digital measuring microscope. Scanned preparations (CEREC) were fitted with milled and crystallized lithium disilicate full coverage restorations and luted with a self-etching adhesive resin cement after hydrofluoric acid etching and silanation. All manufacturer recommendations were followed. Specimens were stored at 37°C/98% humidity for 24 hours. Specimens were tested to failure at a 45° angle to the long axis of the tooth root on a universal testing machine. Failure load was converted to MPa using the available bonding surface area with mean data analyzed using Kruskal-Wallis/Dunn's (p = 0.05) RESULTS: The 3 mm preparation height specimens were similar to the 2 mm specimens, and both demonstrated significantly stronger failure load than the 1 mm axial wall height and flat preparation specimens. The flat preparation and 1 mm axial wall height specimens all failed adhesively, while the 2 mm and 3 mm specimens failed largely due to tooth fracture. Further evidence is provided that CAD/CAM adhesive techniques may compensate for less than ideal preparation features. Under the conditions of this study, bicuspid preparations with a 20° TOC restored with adhesively luted, CAD/CAM e.max CAD crowns require at least 2 mm of axial wall height, but further planned fatigue studies are necessary before definitive recommendations can be made. © 2018 by the American College of Prosthodontists.

Manual for automatic generation of finite element models of spiral bevel gears in mesh

NASA Technical Reports Server (NTRS)

Bibel, G. D.; Reddy, S.; Kumar, A.

1994-01-01

The goal of this research is to develop computer programs that generate finite element models suitable for doing 3D contact analysis of faced milled spiral bevel gears in mesh. A pinion tooth and a gear tooth are created and put in mesh. There are two programs: Points.f and Pat.f to perform the analysis. Points.f is based on the equation of meshing for spiral bevel gears. It uses machine tool settings to solve for an N x M mesh of points on the four surfaces, pinion concave and convex, and gear concave and convex. Points.f creates the file POINTS.OUT, an ASCI file containing N x M points for each surface. (N is the number of node points along the length of the tooth, and M is nodes along the height.) Pat.f reads POINTS.OUT and creates the file tl.out. Tl.out is a series of PATRAN input commands. In addition to the mesh density on the tooth face, additional user specified variables are the number of finite elements through the thickness, and the number of finite elements along the tooth full fillet. A full fillet is assumed to exist for both the pinion and gear.

Un test de la variation en dents de scie du champ magnétique terrestre par les anomalies du champ magnétique sur les dorsales

NASA Astrophysics Data System (ADS)

Westphal, Michel; Munschy, Marc

1999-10-01

In order to test the possible saw-tooth behaviour of the Earth's magnetic field during stable polarity intervals, we selected several magnetic profiles over the East Indian Ridge, the Juan de Fuca Ridge and the East Pacific Rise. We then compared the stacked magnetic anomaly profiles with different models. It appears that neither the uniform pattern nor the saw-tooth pattern fully explain the shape of all anomalies. We propose a new magnetic field model with a gradual transition between Gauss and Matuyama periods and smaller intensities for some short episodes.

Color masking of developmental enamel defects: a case series.

PubMed

Torres, C R G; Borges, A B

2015-01-01

Developmental defects involving color alteration of enamel frequently compromise the esthetic appearance of the tooth. The resin infiltration technique represents an alternative treatment for color masking of these lesions and uniformization of tooth color. This technique is considered relatively simple and microinvasive, since only a minimal portion of enamel is removed. This article illustrates the color-masking effect with resin infiltration of fluorosis and traumatic hypomineralization lesions with a case series. The final esthetic outcomes demonstrated the ability of the resin infiltrant to mask the color of white developmental defect lesions, resulting in satisfactory clinical esthetic improvements. However, in more severe cases, the color-masking effect was not complete.

Wave height estimates from pressure and velocity data at an intermediate depth in the presence of uniform currents

NASA Astrophysics Data System (ADS)

Basu, Biswajit

2017-12-01

Bounds on estimates of wave heights (valid for large amplitudes) from pressure and flow measurements at an arbitrary intermediate depth have been provided. Two-dimensional irrotational steady water waves over a flat bed with a finite depth in the presence of underlying uniform currents have been considered in the analysis. Five different upper bounds based on a combination of pressure and velocity field measurements have been derived, though there is only one available lower bound on the wave height in the case of the speed of current greater than or less than the wave speed. This article is part of the theme issue 'Nonlinear water waves'.

The Effect of Molar Preparation Axial Height on Retention of Adhesively-luted CAD/CAM Ceramic Crowns

DTIC Science & Technology

2015-04-29

IL, USA). The sectioned teeth were then mounted in autopolymerizing denture base methacrylate resin (Diamond D, Keystone Industries, Cherry Hill... Paul , MN, USA) was placed into the intaglio surface of the ceramic restoration. The restoration was then seated onto the tooth using digital finger

Maxillary Sinus Dimensions Decrease as Age and Tooth Loss Increase.

PubMed

Velasco-Torres, Miguel; Padial-Molina, Miguel; Avila-Ortiz, Gustavo; García-Delgado, Raúl; OʼValle, Francisco; Catena, Andrés; Galindo-Moreno, Pablo

2017-04-01

To investigate the correlation between patient-dependent variables and dimensional variations of the maxillary sinus. In this cross-sectional study, a total of 394 individual cone-beam computed tomography scans were evaluated by one calibrated examiner to measure the total volume of the maxillary sinus, the distance between the medial and the lateral walls at 5, 10, and 15 mm vertically from the sinus floor, the height of septa (if present), and the height of the maxillary sinus cavity from both the alveolar crest and the sinus floor to the meatus. Recorded patient-dependent variables were age, gender, and edentulism status. Total maxillary sinus volume was significantly smaller in completely and partially edentulous patients than in dentate subjects. This finding was influenced by age, as older patients exhibited less volume, regardless of gender and edentulism status. Age showed an indirect correlation with the distance to the meatus, the sinus volume, and the mediolateral dimensions. Additionally, the prevalence of accessory meatus in this population was 29.19%. The dimensions of the maxillary sinus are influenced by age and edentulism status being reduced by aging and tooth loss.

Within-wafer CD variation induced by wafer shape

NASA Astrophysics Data System (ADS)

Huang, Chi-hao; Yang, Mars; Yang, Elvis; Yang, T. H.; Chen, K. C.

2016-03-01

In order to meet the increasing storage capacity demand and reduce bit cost of NAND flash memories, 3D stacked vertical flash cell array has been proposed. In constructing 3D NAND flash memories, the bit number per unit area is increased as increasing the number of stacked layers. However, the increased number of stacked layers has made the film stress control extremely important for maintaining good process quality. The residual film stress alters the wafer shape accordingly several process impacts have been readily observed across wafer, such as film deposition non-uniformity, etch rate non-uniformity, wafer chucking error on scanner, materials coating/baking defects, overlay degradation and critical dimension (CD) non-uniformity. The residual tensile and compressive stresses on wafers will result in concave and convex wafer shapes, respectively. This study investigates within-wafer CD uniformity (CDU) associated with wafer shape change induced by the 3D NAND flash memory processes. Within-wafer CDU was correlated with several critical parameters including different wafer bow heights of concave and convex wafer shapes, photo resists with different post exposure baking (PEB) temperature sensitivities, and DoseMapper compensation. The results indicated the trend of within-wafer CDU maintains flat for convex wafer shapes with bow height up to +230um and concave wafer shapes with bow height ranging from 0 ~ -70um, while the within-wafer CDU trends up from -70um to -246um wafer bow heights. To minimize the within-wafer CD distribution induced by wafer warpage, carefully tailoring the film stack and thermal budget in the process flow for maintaining the wafer shape at CDU friendly range is indispensable and using photo-resist materials with lower PEB temperature sensitivity is also suggested. In addition, DoseMapper compensation is also an alternative to greatly suppress the within-wafer CD non-uniformity but the photo-resist profile variation induced by across-wafer PEB temperature non-uniformity attributed to wafer warpage is uncorrectable, and the photo-resist profile variation is believed to affect across-wafer etch bias uniformity to some degree.

Mechanical modelling of tooth wear

PubMed Central

Kallonen, Aki

2016-01-01

Different diets wear teeth in different ways and generate distinguishable wear and microwear patterns that have long been the basis of palaeodiet reconstructions. Little experimental research has been performed to study them together. Here, we show that an artificial mechanical masticator, a chewing machine, occluding real horse teeth in continuous simulated chewing (of 100 000 chewing cycles) is capable of replicating microscopic wear features and gross wear on teeth that resemble wear in specimens collected from nature. Simulating pure attrition (chewing without food) and four plant material diets of different abrasives content (at n = 5 tooth pairs per group), we detected differences in microscopic wear features by stereomicroscopy of the chewing surface in the number and quality of pits and scratches that were not always as expected. Using computed tomography scanning in one tooth per diet, absolute wear was quantified as the mean height change after the simulated chewing. Absolute wear increased with diet abrasiveness, originating from phytoliths and grit. In combination, our findings highlight that differences in actual dental tissue loss can occur at similar microwear patterns, cautioning against a direct transformation of microwear results into predictions about diet or tooth wear rate. PMID:27411727

Plume Dispersion over Idealized Urban-liked Roughness with Height Variation: an LES Approach

NASA Astrophysics Data System (ADS)

Wong, Colman Ching Chi; Liu, Chun-Ho

2013-04-01

Human activities (e.g. vehicular emission) are the primary pollutant sources affecting the health and living quality of stakeholders in modern compact cities. Gaussian plume dispersion model is commonly used for pollutant distribution estimate that works well over rural areas with flat terrain. However, its major parameters, dispersion coefficients, exclude the effect of surface roughness that unavoidably prone to error handling the pollutant transport in the urban boundary layer (UBL) over building roughness. Our recent large-eddy simulation (LES) has shown that urban surfaces affect significantly the pollutant dispersion over idealized, identical two-dimensional (2D) street canyons of uniform height. As an extension to our on-going effort, this study is conceived to investigate how rough urban surfaces, which are constructed by 2D street canyons of non-uniform height, modify the UBL pollutant dispersion . A series of LESs with idealized roughness elements of non-uniform heights were performed in neutral stratification. Building models with two different heights were placed alternatively in the computational domain to construct 2D street canyons in cross flows. The plume dispersion from a ground-level passive pollutant source over more realistic urban areas was then examined. Along with the existing building-height-to-street-width (aspect) ratio (AR), a new parameter, building-height variability (BHV), is used to measure the building height unevenness. Four ARs (1, 0.5, 0.25 and 0.125) and three BHVs (20%, 40% and 60%) were considered in this study. Preliminary results show that BHV greatly increases the aerodynamic roughness of the hypothetical urban surfaces for narrow street canyons. Analogous to our previous findings, the air exchange rate (ACH) of street canyons increases with increasing friction factor, implying that street-level ventilation could be improved by increasing building roughness via BHV. In addition, the parameters used in dispersion coefficient estimates are related to the friction factor in the way similar to that of uniform street canyons, i.e. they are linear functions of friction factor when the roughness is small and become insensitive to friction factor thereafter over very rough surfaces. It is thus suggested that aerodynamic resistance is the key factor affecting the air quality in urban areas. Moreover, the friction factor could be used to parameterize the dispersion coefficients over different roughness elements.

Taking advantage of modern turbines

NASA Astrophysics Data System (ADS)

Thresher, Robert

2018-06-01

Wind facilities have generally deployed turbines of the same power and height in regular uniform arrays. Now, the modern generation of turbines, with customer-selectable tower heights and larger rotors, can significantly increase wind energy's economic potential using less land to generate cheaper electricity.

Spatial height directed microfluidic synthesis of transparent inorganic upconversion nano film

NASA Astrophysics Data System (ADS)

Liu, Xiaoxia; Zhu, Cheng; Liao, Wei; Jin, Junyang; Ni, Yaru; Lu, Chunhua; Xu, Zhongzi

2017-11-01

A microfluidic-based synthesis of an inorganic upconversion nano film has been developed with a large area of dense-distributed NaYF4 crystal grains in a silica glass micro-reactor and the film exhibits high transparence, strong upconversion luminescence and robust adhesion with the substrate. The spatial heights of micro-reactors are tuned between 31 and 227 mm, which can regulate flow regimes. The synergistic effect of spatial height and fluid regime is put forward, which influences diffusion paths and assembly ways of different precursor molecules and consequently directs final distributions and morphologies of crystal grains, as well as optical properties due to diversity of surface and thickness of films. The spatial height of 110 mm is advantageous for high transmittance of upconversion film due to the flat surface and appropriate film thickness of 67 nm. The height of 150 mm is in favor of uniform distribution of upconversion fluorescence and achieving the strongest fluorescence due to minimized optical loss. Such a transparent upconversion film with a large area of uniform distribution is promising to promote the application of upconversion materials and spatial height directed microfluidic regime have a certain significance on many microfluidic synthesis.

Influence of the expansion screw height on the dental effects of the hyrax expander: a study with finite elements.

PubMed

Araugio, Rafael Marques de Sousa; Landre, Jánes; Silva, Diana de Lourdes Almeida; Pacheco, Wellington; Pithon, Matheus Melo; Oliveira, Dauro Douglas

2013-02-01

Our objective was to evaluate the influence of the expansion screw height of a hyrax expander on the degree of dental inclination during rapid maxillary expansion by using the finite element method. The hyrax expander and the maxillary arch were modeled by using Solidworks software (Dassault Systèmes, Paris, France). Three distinct finite element method models were created by simulating different screw heights relative to the plane that intersected the center of resistance of the maxillary first molars. These 3 relative positions were 10 mm below the maxillary first molars' center of resistance, at the same level as the maxillary first molars' center of resistance, and 10 mm above the maxillary first molars' center of resistance. The initial activation of the expanders was simulated, and tooth displacements for each finite element method model were registered in the buccolingual, corono-apical, and mesiodistal directions. The simulations tested showed that the 3 hyrax screw heights had different dental tipping tendencies. When the screw was simulated below the maxillary first molars' center of resistance, buccal tipping of the crowns and lingual tipping of the roots were registered. This tendency decreased when the screw was simulated at the same level as the maxillary first molars' center of resistance. However, when the screw was simulated above the maxillary first molars' center of resistance, the tipping tendency was inverted, with the crowns displaying lingual tipping and the roots displaying buccal tipping. These findings might explain the importance of carefully planning the height of the hyrax expander screw, since, depending on this position, different tooth movements can be achieved. From an orthopedic perspective, the ideal screw position might be slightly above the maxillary first molars' center of resistance; this would generate less dental tipping. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Vertical uniformity of cells and nuclei in epithelial monolayers.

PubMed

Neelam, Srujana; Hayes, Peter Robert; Zhang, Qiao; Dickinson, Richard B; Lele, Tanmay P

2016-01-22

Morphological variability in cytoskeletal organization, organelle position and cell boundaries is a common feature of cultured cells. Remarkable uniformity and reproducibility in structure can be accomplished by providing cells with defined geometric cues. Cells in tissues can also self-organize in the absence of directing extracellular cues; however the mechanical principles for such self-organization are not understood. We report that unlike horizontal shapes, the vertical shapes of the cell and nucleus in the z-dimension are uniform in cells in cultured monolayers compared to isolated cells. Apical surfaces of cells and their nuclei in monolayers were flat and heights were uniform. In contrast, isolated cells, or cells with disrupted cell-cell adhesions had nuclei with curved apical surfaces and variable heights. Isolated cells cultured within micron-sized square wells displayed flat cell and nuclear shapes similar to cells in monolayers. Local disruption of nuclear-cytoskeletal linkages resulted in spatial variation in vertical uniformity. These results suggest that competition between cell-cell pulling forces that expand and shorten the vertical cell cross-section, thereby widening and flattening the nucleus, and the resistance of the nucleus to further flattening results in uniform cell and nuclear cross-sections. Our results reveal the mechanical principles of self-organized vertical uniformity in cell monolayers.

Self-consistent molecular dynamics formulation for electric-field-mediated electrolyte transport through nanochannels

NASA Astrophysics Data System (ADS)

Raghunathan, A. V.; Aluru, N. R.

2007-07-01

A self-consistent molecular dynamics (SCMD) formulation is presented for electric-field-mediated transport of water and ions through a nanochannel connected to reservoirs or baths. The SCMD formulation is compared with a uniform field MD approach, where the applied electric field is assumed to be uniform, for 2nm and 3.5nm wide nanochannels immersed in a 0.5M KCl solution. Reservoir ionic concentrations are maintained using the dual-control-volume grand canonical molecular dynamics technique. Simulation results with varying channel height indicate that the SCMD approach calculates the electrostatic potential in the simulation domain more accurately compared to the uniform field approach, with the deviation in results increasing with the channel height. The translocation times and ionic fluxes predicted by uniform field MD can be substantially different from those predicted by the SCMD approach. Our results also indicate that during a 2ns simulation time K+ ions can permeate through a 1nm channel when the applied electric field is computed self-consistently, while the permeation is not observed when the electric field is assumed to be uniform.

Taking advantage of modern turbines

DOE PAGES

Thresher, Robert

2018-05-14

Here, wind facilities have generally deployed turbines of the same power and height in regular uniform arrays. Now, the modern generation of turbines, with customer-selectable tower heights and larger rotors, can significantly increase wind energy's economic potential using less land to generate cheaper electricity.

Taking advantage of modern turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thresher, Robert

Here, wind facilities have generally deployed turbines of the same power and height in regular uniform arrays. Now, the modern generation of turbines, with customer-selectable tower heights and larger rotors, can significantly increase wind energy's economic potential using less land to generate cheaper electricity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Chien-Chih; Hsu, Pei-Lun; Lin, Li

A particular edge-dependent inversion current behavior of metal-oxide-semiconductor (MOS) tunneling diodes was investigated utilizing square and comb-shaped electrodes. The inversion tunneling current exhibits the strong dependence on the tooth size of comb-shaped electrodes and oxide thickness. Detailed illustrations of current conduction mechanism are developed by simulation and experimental measurement results. It is found that the electron diffusion current and Schottky barrier height lowering for hole tunneling current both contribute on inversion current conduction. In MOS tunneling photodiode applications, the photoresponse can be improved by decreasing SiO{sub 2} thickness and using comb-shaped electrodes with smaller tooth spacing. Meantime, the high andmore » steady photosensitivity can also be approached by introducing HfO{sub 2} into dielectric stacks.« less

Determinants of alveolar ridge preservation differ by anatomic location

PubMed Central

Leblebicioglu, Binnaz; Salas, Mabel; Ort, Yirae; Johnson, Ashley; Yildiz, Vedat O.; Kim, Do-Gyoon; Agarwal, Sudha; Tatakis, Dimitris N.

2016-01-01

Aim To investigate and compare outcomes following alveolar ridge preservation (ARP) in posterior maxilla and mandible. Methods Twenty-four patients (54 ± 3 years) with single posterior tooth extraction were included. ARP was performed with freeze-dried bone allograft and collagen membrane. Clinical parameters were recorded at extraction and re-entry. Harvested bone cores were analysed by microcomputed tomography (micro-CT), histomorphometry and immunohistochemistry. Results In both jaws, ARP prevented ridge height loss, but ridge width was significantly reduced by approximately 2.5 mm. Healing time, initial clinical attachment loss and amount of keratinized tissue at extraction site were identified as determinants of ridge height outcome. Buccal plate thickness and tooth root length were identified as determinants of ridge width outcome. In addition, initial ridge width was positively correlated with ridge width loss. Micro-CT revealed greater mineralization per unit volume in new bone compared with existing bone in mandible (p < 0.001). Distributions of residual graft, new cellular bone and immature tissue were similar in both jaws. Conclusion Within the limitations of this study, the results indicate that in different anatomic locations different factors may determine ARP outcomes. Further studies are needed to better understand determinants of ARP outcomes. PMID:23432761

Computational and theoretical analysis of free surface flow in a thin liquid film under zero and normal gravity

NASA Technical Reports Server (NTRS)

Faghri, Amir; Swanson, Theodore D.

1988-01-01

The results of a numerical computation and theoretical analysis are presented for the flow of a thin liquid film in the presence and absence of a gravitational body force. Five different flow systems were used. Also presented are the governing equations and boundary conditions for the situation of a thin liquid emanating from a pressure vessel; traveling along a horizontal plate with a constant initial height and uniform initial velocity; and traveling radially along a horizontal disk with a constant initial height and uniform initial velocity.

Reproducible direct exposure environmental testing of metal-based magnetic media

NASA Technical Reports Server (NTRS)

Sides, Paul J.

1994-01-01

A flow geometry and flow rate for mixed flowing gas testing is proposed. Use of an impinging jet of humid polluted air can provide a uniform and reproducible exposure of coupons of metal-based magnetic media. Numerical analysis of the fluid flow and mass transfer in such as system has shown that samples confined within a distance equal to the nozzle radius on the surface of impingement are uniformly accessible to pollutants in the impinging gas phase. The critical factor is the nozzle height above the surface of impingement. In particular, the uniformity of exposure is less than plus/minus 2% for a volumetric flow rate of 1600 cm(exp 3)/minute total flow with the following specifications: For a one inch nozzle, the height of the nozzle opening above the stage should be 0.177 inches; for a 2 inch nozzle - 0.390 inches. Not only is the distribution uniform, but one can calculate the maximum delivery rate of pollutants to the samples for comparison with the observed deterioration.

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

36 CFR 910.61 - Height of development.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Height of development. 910.61 Section 910.61 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

36 CFR 910.54 - Build-to height.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Build-to height. 910.54 Section 910.54 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

36 CFR 910.54 - Build-to height.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Build-to height. 910.54 Section 910.54 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

36 CFR 910.61 - Height of development.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Height of development. 910.61 Section 910.61 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

Exploring the Potential of Laser Ablation Carbon Isotope Analysis for Examining Ecology during the Ontogeny of Middle Pleistocene Hominins from Sima de los Huesos (Northern Spain).

PubMed

Garcia, Nuria; Feranec, Robert S; Passey, Benjamin H; Cerling, Thure E; Arsuaga, Juan Luis

2015-01-01

Laser ablation of tooth enamel was used to analyze stable carbon isotope compositions of teeth of hominins, red deer, and bears from middle Pleistocene sites in the Sierra de Atapuerca in northern Spain, to investigate the possibility that this technique could be used as an additional tool to identify periods of physiological change that are not detectable as changes in tooth morphology. Most of the specimens were found to have minimal intra-tooth variation in carbon isotopes (< 2.3‰), suggesting isotopically uniform diets through time and revealing no obvious periods of physiological change. However, one of the two sampled hominin teeth displayed a temporal carbon isotope shift (3.2‰) that was significantly greater than observed for co-occurring specimens. The δ13C value of this individual averaged about -16‰ early in life, and -13‰ later in life. This isotopic change occurred on the canine crown about 4.2 mm from the root, which corresponds to an approximate age of two to four years old in modern humans. Our dataset is perforce small owing to the precious nature of hominid teeth, but it demonstrates the potential utility of the intra-tooth isotope profile method for extracting ontogenetic histories of human ancestors.

26. Detail view of drum girder with rollers below, resting ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Detail view of drum girder with rollers below, resting on fixed turntable upon masonry center pier. Swing drive shaft (vertical) is turned by level gear of horizontal shaft (protruding through machine room wall), which turns pinion gear toothed to fixed turntable rack below rollers. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

29 CFR 1926.1052 - Stairways.

Code of Federal Regulations, 2011 CFR

2011-07-01

...° from horizontal. (3) Riser height and tread depth shall be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or... having four or more risers or rising more than 30 inches (76 cm), whichever is less, shall be equipped...

29 CFR 1926.1052 - Stairways.

Code of Federal Regulations, 2012 CFR

2012-07-01

...° from horizontal. (3) Riser height and tread depth shall be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or... having four or more risers or rising more than 30 inches (76 cm), whichever is less, shall be equipped...

29 CFR 1926.1052 - Stairways.

Code of Federal Regulations, 2010 CFR

2010-07-01

...° from horizontal. (3) Riser height and tread depth shall be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or... having four or more risers or rising more than 30 inches (76 cm), whichever is less, shall be equipped...

29 CFR 1926.1052 - Stairways.

Code of Federal Regulations, 2013 CFR

2013-07-01

...° from horizontal. (3) Riser height and tread depth shall be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or... having four or more risers or rising more than 30 inches (76 cm), whichever is less, shall be equipped...

29 CFR 1926.1052 - Stairways.

Code of Federal Regulations, 2014 CFR

2014-07-01

...° from horizontal. (3) Riser height and tread depth shall be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or... having four or more risers or rising more than 30 inches (76 cm), whichever is less, shall be equipped...

A Review of the Positive Influence of Crown Contours on Soft-Tissue Esthetics.

PubMed

Kinsel, Richard P; Pope, Bryan I; Capoferri, Daniele

2015-05-01

Successful crown restorations duplicate the natural tooth in hue, chroma, value, maverick colors, and surface texture. Equally important is the visual harmony of the facial and proximal soft-tissue contours, which requires the collaborative skills of the restorative dentist, periodontist, and dental technician. The treatment team must understand the biologic structures adjacent to natural dentition and dental implants. This report describes the potential for specifically designed restorative contours to dictate the optimal gingival profile for tooth-supported and implant-supported crowns. Showing several cases, the article explains how esthetic soft-tissue contours enhance the definitive crown restoration, highlights the importance of clinical evaluation of adjacent biologic structures, and discusses keys to predicting when the proximal papilla has the potential to return to a favorable height and shape.

Injectable bone substitute to preserve alveolar ridge resorption after tooth extraction: a study in dog.

PubMed

Boix, D; Weiss, P; Gauthier, O; Guicheux, J; Bouler, J-M; Pilet, P; Daculsi, G; Grimandi, G

2006-11-01

The aim of the present study was to assess the efficacy of a ready-to-use injectable bone substitute on the prevention of alveolar ridge resorption after tooth extraction. Maxillary and mandibular premolars were extracted from 3 Beagle dogs with preservation of alveolar bone. Thereafter, distal sockets were filled with an injectable bone substitute (IBS), obtained by combining a polymer solution and granules of a biphasic calcium phosphate (BCP) ceramic. As a control, the mesial sockets were left unfilled. After a 3 months healing period, specimens were removed and prepared for histomorphometric evaluation with image analysis. Histomorphometric study allowed to measure the mean and the maximal heights of alveolar crest modifications. Results always showed an alveolar bone resorption in unfilled sockets. Resorption in filled maxillary sites was significantly lower than in control sites. Interestingly, an alveolar ridge augmentation was measured in mandibular filled sockets including 30% of newly-formed bone. It was concluded that an injectable bone substitute composed of a polymeric carrier and calcium phosphate can significantly increase alveolar ridge preservation after tooth extraction.

Numerical simulation of temperature distribution in cylindrical ilmenite (FeTiO3) due to microwave heating

NASA Astrophysics Data System (ADS)

Hidayat, Mas Irfan P.; Fellicia, Dian Mughni; Rafandi, Ferdiansyah Iqbal

2018-04-01

Microwave assisted heating has been extensively used in materials processing particularly in extraction of TiO2 from Ilmenite (FeTiO3) minerals. Nevertheless, this method could generate non-uniform temperature distribution during the heating process. The observation of this phenomena in cylindrical ilmenite has been conducted by numerical simulation using finite element method according to the Poynthing's theorem. Four different cylinders with variation on its height were simulated in ANSYS 17 with input microwave power of 5.5 Kw. The results indicated that height of heated object could vigorously influence the uniformity of temperature inside the body.

Marginal Fit of CEREC Crowns at Different Finish Line Curvatures

DTIC Science & Technology

2015-06-01

percolation of bacteria {Beschnidt & Strub, 1999). This will compromise 13 the longevity of the tooth, increasing the risk of dental caries caused...and Practice of Caries Prevention. Journal of american dental association, 131, 887-899. Ferrari, M. {1991). Cement thickness and microlikage under...Prosthodontic Graduate Program Naval Postgraduate Dental School Uniformed Services University of the Health Sciences in partial fulfillment of the

New Design and Improvement of Planetary Gear Trains

NASA Technical Reports Server (NTRS)

Handschuh, Robert (Technical Monitor); Litvin, Faydor L.; Fuentes, Alfonso; Vecchiato, Daniele; Gonzalez-Perez, Ignacio

2004-01-01

The development of new types of planetary and planetary face-gear drives is proposed. The new designs are based on regulating backlash between the gears and modifying the tooth surfaces to improve the design. The goal of this work is to obtain a nearly uniform distribution of load between the planet gears. In addition, a new type of planetary face-gear drive was developed in this project.

Effect of increased crown height on stress distribution in short dental implant components and their surrounding bone: A finite element analysis.

PubMed

Bulaqi, Haddad Arabi; Mousavi Mashhadi, Mahmoud; Safari, Hamed; Samandari, Mohammad Mahdi; Geramipanah, Farideh

2015-06-01

Implants in posterior regions of the jaw require short dental implants with long crown heights, leading to increased crown-to-implant ratios and mechanical stress. This can lead to fracture and screw loosening. The purpose of this study was to investigate the dynamic nature and behavior of prosthetic components and preimplant bone and evaluate the effect of increased crown height space (CHS) and crown-to-implant ratio on stress concentrations under external oblique forces. The severely resorbed bone of a posterior mandible site was modeled with Mimics and Catia software. A second mandibular premolar tooth was modeled with CHS values of 8.8, 11.2, 13.6, and 16 mm. A Straumann implant (4.1×8 mm), a directly attached crown, and an abutment screw were modeled with geometric data and designed by using SolidWorks software. Abaqus software was used for the dynamic simulation of screw tightening and the application of an external load to the buccal cusp at a 75.8-degree angle with the occlusal plane. The distribution of screw load and member load at each step was compared, and the stress values were calculated within the dental implant complex and surrounding bone. During tightening, the magnitude and distribution of the preload and clamp load were uniform and equal at the cross section of all CHSs. Under an external load, the screw load decreased and member load increased. An increase in the CHS caused the corresponding distribution to become more nonuniform and increased the maximum compressive and tensile stresses in the preimplant bone. Additionally, the von Mises stress decreased at the abutment screw and increased at the abutment and fixture. Under nonaxial forces, increased CHS does not influence the decrease in screw load or increase in member load. However, it contributes to screw loosening and fatigue fracture by skewing the stress distribution to the transverse section of the implant. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Influence of clinical baseline findings on the survival of 2 post systems: a randomized clinical trial.

PubMed

Schmitter, Marc; Rammelsberg, Peter; Gabbert, Olaf; Ohlmann, Brigitte

2007-01-01

The aim of this prospective randomized controlled trial was to evaluate the influence of clinical baseline characteristics on the survival of 2 post systems. One hundred patients needing a post were included. Half the patients received a glass fiber-reinforced post (FRP), and the other half received metal screw posts (MSP). The posts were assigned randomly. In addition to demographic data, the following parameters were recorded: type of tooth (incisor/canine versus molar/premolar), length of the post in relation to root length (percentage), extent of coronal tooth destruction (percentage), ferrule height (in millimeters), type of restoration (fixed or removable partial denture), and presence of antagonistic contacts (yes/no). After at least 1 year (mean: 13.84 months), the patients were recalled. Statistical analysis was performed using the log-rank test and Cox regression analysis. The survival rate of FRPs was 93.5%. In the MSP group, the survival rate was significantly lower (75.6%; log-rank test, P = .049). Additionally, the metal posts were associated with more unfavorable complications, for example, root fracture. The type of the tooth and the degree of coronal tooth destruction influenced the survival of MSPs, whereas no influence of these variables could be seen for FRPs. FRPs are superior to MSPs with respect to short-term clinical performance. Especially for MSPs, clinical survival depends on several variables.

Esthetic evaluation of single-tooth implants in the anterior maxilla following autologous bone augmentation.

PubMed

Hof, M; Pommer, B; Strbac, G D; Sütö, D; Watzek, G; Zechner, W

2013-08-01

Autologous bone augmentation to rebuild compromised alveolar ridge contour prior to implant placement allows for favorable three-dimensional implant positioning to achieve optimum implant esthetics. The aim of the present study was to evaluate peri-implant soft tissue conditions around single-tooth implants following bone grafts in the esthetic zone of the maxilla. Sixty patients underwent autologous bone augmentation of deficient maxillary sites prior to placement of 85 implants in the esthetic zone. In case of multiple implants per patient, one implant was randomly selected. Objective evaluation of 60 single-tooth implants was performed using the Pink-Esthetic-Score (PES) and Papilla Index (PI) and supplemented by subjective patient evaluation, as well as clinical and radiologic examination. Objective ratings of implant esthetics were satisfactory (median PES: 11, median PI: 2) and significantly correlated with high patient satisfaction (mean VAS score: 80%). Both esthetic indices demonstrated respectable levels of inter- as well as intra-observer agreement. Poor implant esthetics (low PES and PI ratings) were significantly associated with increased anatomic crown height, while no influence of horizontal implant-tooth distance could be found. The present investigation indicates that favorable esthetic results may be achieved in the augmented anterior maxilla. However, bony reconstruction of compromised alveolar ridges does not guarantee optimum implant esthetics. © 2011 John Wiley & Sons A/S.

Exploring the Potential of Laser Ablation Carbon Isotope Analysis for Examining Ecology during the Ontogeny of Middle Pleistocene Hominins from Sima de los Huesos (Northern Spain)

PubMed Central

Garcia, Nuria; Feranec, Robert S.; Passey, Benjamin H.; Cerling, Thure E.; Arsuaga, Juan Luis

2015-01-01

Laser ablation of tooth enamel was used to analyze stable carbon isotope compositions of teeth of hominins, red deer, and bears from middle Pleistocene sites in the Sierra de Atapuerca in northern Spain, to investigate the possibility that this technique could be used as an additional tool to identify periods of physiological change that are not detectable as changes in tooth morphology. Most of the specimens were found to have minimal intra-tooth variation in carbon isotopes (< 2.3‰), suggesting isotopically uniform diets through time and revealing no obvious periods of physiological change. However, one of the two sampled hominin teeth displayed a temporal carbon isotope shift (3.2‰) that was significantly greater than observed for co-occurring specimens. The δ13C value of this individual averaged about -16‰ early in life, and -13‰ later in life. This isotopic change occurred on the canine crown about 4.2 mm from the root, which corresponds to an approximate age of two to four years old in modern humans. Our dataset is perforce small owing to the precious nature of hominid teeth, but it demonstrates the potential utility of the intra-tooth isotope profile method for extracting ontogenetic histories of human ancestors. PMID:26673156

Estimating canopy bulk density and canopy base height for interior western US conifer stands

Treesearch

Seth A. Ex; Frederick W. Smith; Tara L. Keyser; Stephanie A. Rebain

2016-01-01

Crown fire hazard is often quantified using effective canopy bulk density (CBD) and canopy base height (CBH). When CBD and CBH are estimated using nonlocal crown fuel biomass allometries and uniform crown fuel distribution assumptions, as is common practice, values may differ from estimates made using local allometries and nonuniform...

Damping ratio analysis of tooth stability under various simulated degrees of vertical alveolar bone loss and different root types.

PubMed

Ho, Kuo-Ning; Lee, Sheng-Yang; Huang, Haw-Ming

2017-08-03

The purpose of this study was to evaluate the feasibility of using damping ratio (DR) analysis combined with resonance frequency (RF) and periotest (PTV) analyses to provide additional information about natural tooth stability under various simulated degrees of alveolar vertical bone loss and various root types. Three experimental tooth models, including upper central incisor, upper first premolar, and upper first molar were fabricated using Ti6Al4V alloy. In the tooth models, the periodontal ligament and alveolar bone were simulated using a soft lining material and gypsum, respectively. Various degrees of vertical bone loss were simulated by decreasing the surrounding bone level apically from the cementoenamel junction in 2-mm steps incrementally downward for 10 mm. A commercially available RF analyzer was used to measure the RF and DR of impulse-forced vibrations on the tooth models. The results showed that DRs increased as alveolar vertical bone height decreased and had high coefficients of determination in the linear regression analysis. The damping ratio of the central incisor model without a simulated periodontal ligament were 11.95 ± 1.92 and 27.50 ± 0.67% respectively when their bone levels were set at 2 and 10 mm apically from the cementoenamel junction. These values significantly changed to 28.85 ± 2.54% (p = 0.000) and 51.25 ± 4.78% (p = 0.003) when the tooth model was covered with simulated periodontal ligament. Moreover, teeth with different root types showed different DR and RF patterns. Teeth with multiple roots had lower DRs than teeth with single roots. Damping ratio analysis combined with PTV and RF analysis provides more useful information on the assessment of changes in vertical alveolar bone loss than PTV or RF analysis alone.

Mathematical equation for prediction of cat mandibular canal height dimension based on canine tooth width measurement.

PubMed

Santos, Miguel; Carreira, L Miguel

2016-06-01

The present study was performed in a sample of 33 cats and aimed (1) to characterise the mandible height (Mh), mandibular canal height (MCh) and the distance between the interdental alveolar margin and the mandibular canal (dIAM-MC); and (2) to develop a mathematical model for dimension prediction of MCh using the patient's age, weight (Wg) and canine tooth width at the free gingival margin level (wCGM) that was easily accessible during the oral examination. Age, sex, breed, weight, skull type and the wCGM were the recorded variables for each patient. Right and left lateral view skull radiographs were made followed by measurements of the mandible anatomical structures, taken between the third premolar distal root and the fourth premolar proximal root. Results were considered statistically significant for P values <0.05, and statistical analysis was performed using SPSS software. We observed a strong correlation only between wCGM and MCh, and a prediction mathematical model was developed to calculate the MCh, with a standard error of only 0.4 mm. Our study allows a surgeon to establish relationships between a physical parameter, such as wCGM, evaluated in an oral examination, and the mandibular canal, which is a very important anatomical structure to consider in surgical procedures. Ideally, surgeons should always plan their mandible work only after obtaining a final diagnosis achieved through the use of complementary imaging exams, such as intra- and extra-oral radiographs. Thus, this mathematical equation offers an additional tool, providing more information on the relationships between oral anatomical structures, reducing the risk of iatrogenic lesions and promoting patient safety. © ISFM and AAFP 2015.

Rates of anterior tooth wear in Middle Pleistocene hominins from Sima de los Huesos (Sierra de Atapuerca, Spain).

PubMed

Bermúdez de Castro, J M; Martinón-Torres, M; Sarmiento, S; Lozano, M; Arsuaga, J L; Carbonell, E

2003-10-14

This study presents quantitative data on the rates of anterior tooth wear in a Pleistocene human population. The data were obtained for the hominin sample of the Sima de los Huesos site in Atapuerca, Spain. The fossil record belongs to a minimum of 28 individuals of the same biological population, assigned to the species Homo heidelbergensis. We have estimated the original and the preserved crown height of the mandibular incisors (I1 and I2) of 11 individuals, whose age at death can be ascertained from the mineralization stage and tooth eruption. Results provide a range of 0.276-0.348 and 0.288-0.360 mm per year for the mean wear rate of the mandibular I1 and I2, respectively, in individuals approximately 16-18 years old. These data suggest that incisors' crowns would be totally worn out toward the fifth decade of life. Thus, we expect the life expectancy of this population to be seriously limited. These data, which could be contrasted with results obtained on hominins at other sites, could be of interest for estimating the death age of adult individuals.

Craniofacial morphology, dental occlusion, tooth eruption, and dental maturity in boys of short stature with or without growth hormone deficiency.

PubMed

Kjellberg, H; Beiring, M; Albertsson Wikland, K

2000-10-01

The aim of this project was to study the craniofacial morphology, dental occlusion, dental maturation and tooth eruption in short-statured boys with growth hormone secretion ranging from low to high. The measurements from lateral and posteroanterior cephalograms, orthopantomograms and plaster models were used. Almost all linear measurements of the facial structures were significantly smaller. A disproportionate growth in the cranial base structures as well as in the jaws resulted in facial retrognathia, a proportionately smaller posterior than anterior facial height, and a steep vertical inclination of the mandible. Dental crowding was more common and the overbite was small. Dental maturity and tooth eruption were delayed 1.2 and 1.3 yr, respectively. No significant differences between the idiopathic short-statured and the growth hormone-deficient group in any of the above-mentioned variables were found. It can be concluded that although most of the cephalometric variables measured differed significantly from the average, the facial appearance of the boys is not conspicuous and is of minor clinical importance. However, the short-statured boys might be in greater need of orthodontic treatment due to the higher percentage of dental crowding.

Rates of anterior tooth wear in Middle Pleistocene hominins from Sima de los Huesos (Sierra de Atapuerca, Spain)

PubMed Central

de Castro, J. M. Bermúdez; Martinón-Torres, M.; Sarmiento, S.; Lozano, M.; Arsuaga, J. L.; Carbonell, E.

2003-01-01

This study presents quantitative data on the rates of anterior tooth wear in a Pleistocene human population. The data were obtained for the hominin sample of the Sima de los Huesos site in Atapuerca, Spain. The fossil record belongs to a minimum of 28 individuals of the same biological population, assigned to the species Homo heidelbergensis. We have estimated the original and the preserved crown height of the mandibular incisors (I1 and I2) of 11 individuals, whose age at death can be ascertained from the mineralization stage and tooth eruption. Results provide a range of 0.276–0.348 and 0.288–0.360 mm per year for the mean wear rate of the mandibular I1 and I2, respectively, in individuals ≈16–18 years old. These data suggest that incisors' crowns would be totally worn out toward the fifth decade of life. Thus, we expect the life expectancy of this population to be seriously limited. These data, which could be contrasted with results obtained on hominins at other sites, could be of interest for estimating the death age of adult individuals. PMID:14528001

Cone-Beam Computed Tomography and Interdisciplinary Dentofacial Therapy: An American Academy of Periodontology Best Evidence Review Focusing on Risk Assessment of the Dentoalveolar Bone Changes Influenced by Tooth Movement.

PubMed

Mandelaris, George A; Neiva, Rodrigo; Chambrone, Leandro

2017-10-01

The aim of this systematic review is to evaluate whether cone-beam computed tomography (CBCT) imaging can be used to assess dentoalveolar anatomy critical to the periodontist when determining risk assessment for patients undergoing orthodontic therapy using fixed or removable appliances. Both observational and interventional trials reporting on the use of CBCT imaging assessing the impact of orthodontic/dentofacial orthopedic treatment on periodontal tissues (i.e., alveolar bone) were included. Changes in the alveolar bone thickness and height around natural teeth as well as treatment costs were evaluated. MEDLINE (via PubMed) and EMBASE databases were searched for articles published in the English language, up to and including July 2016, and extracted data were organized into evidence tables. Thirteen studies were included in this systematic review describing the positive or deleterious changes on the alveolar bone surrounding natural teeth undergoing orthodontic tooth movement or influenced by orthopedic forces through fixed appliances. Clinical recommendation summaries presenting the strengths and weaknesses of the evidence in terms of benefits and harms were generated. CBCT imaging can improve the periodontal diagnostic acumen regarding alveolar bone alterations influenced by orthodontic tooth movement and can help determine risk assessment prior to such intervention. Clinicians are also better informed to determine risk assessment and develop preventative or plan interceptive periodontal augmentation (soft tissue and/or bone augmentation) therapies for patients undergoing orthodontic tooth movement. These considerations are recognized as being especially critical for treatment approaches in patients where buccal tooth movement (expansion) is planned in the anterior mandible or involving the maxillary premolars.

Uniform height island growth on Pb/Si(111) at low temperatures and QSE

NASA Astrophysics Data System (ADS)

Tringides, Michael C.

2002-03-01

Highly uniform height Pb(111) islands (which can differ by bilayer height increments) of flat tops and steep edges can be grown on Pb/Si(111) at low temperatures 120K

Nitric Acid and Benomyl Stimulate Rapid Height Growth of Longleaf Pine

Treesearch

A.G. Kais; R.C. Hare; J.P. Barnett

1984-01-01

Rapid height growth of longleaf pine seedlings, important to production of uniform, even-aged stands, can be promoted by controlling brown-spot needle blight and weed competition, and by increasing soil fertility. Root systems of container-grown longleaf pine seedlings were dip-treated in either benomyl/clay mix (10 percent a.i. benomyl) or clay control and planted...

Dual-scan technique for the customization of zirconia computer-aided design/computer-aided manufacturing frameworks.

PubMed

Andreiuolo, Rafael Ferrone; Sabrosa, Carlos Eduardo; Dias, Katia Regina H Cervantes

2013-09-01

The use of bi-layered all-ceramic crowns has continuously grown since the introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) zirconia cores. Unfortunately, despite the outstanding mechanical properties of zirconia, problems related to porcelain cracking or chipping remain. One of the reasons for this is that ceramic copings are usually milled to uniform thicknesses of 0.3-0.6 mm around the whole tooth preparation. This may not provide uniform thickness or appropriate support for the veneering porcelain. To prevent these problems, the dual-scan technique demonstrates an alternative that allows the restorative team to customize zirconia CAD/CAM frameworks with adequate porcelain thickness and support in a simple manner.

Dust in the wind: How climate variables and volcanic dust affect rates of tooth wear in Central American howling monkeys.

PubMed

Spradley, Jackson P; Glander, Kenneth E; Kay, Richard F

2016-02-01

Two factors have been considered important contributors to tooth wear: dietary abrasives in plant foods themselves and mineral particles adhering to ingested food. Each factor limits the functional life of teeth. Cross-population studies of wear rates in a single species living in different habitats may point to the relative contributions of each factor. We examine macroscopic dental wear in populations of Alouatta palliata (Gray, 1849) from Costa Rica (115 specimens), Panama (19), and Nicaragua (56). The sites differ in mean annual precipitation, with the Panamanian sites receiving more than twice the precipitation of those in Costa Rica or Nicaragua (∼3,500 mm vs. ∼1,500 mm). Additionally, many of the Nicaraguan specimens were collected downwind of active plinian volcanoes. Molar wear is expressed as the ratio of exposed dentin area to tooth area; premolar wear was scored using a ranking system. Despite substantial variation in environmental variables and the added presence of ash in some environments, molar wear rates do not differ significantly among the populations. Premolar wear, however, is greater in individuals collected downwind from active volcanoes compared with those living in environments that did not experience ash-fall. Volcanic ash seems to be an important contributor to anterior tooth wear but less so in molar wear. That wear is not found uniformly across the tooth row may be related to malformation in the premolars due to fluorosis. A surge of fluoride accompanying the volcanic ash may differentially affect the premolars as the molars fully mineralize early in the life of Alouatta. © 2015 Wiley Periodicals, Inc.

Effectiveness of decoronation technique in the treatment of ankylosis: A systematic review.

PubMed

Mohadeb, Jhassu Varsha Naveena; Somar, Mirinal; He, Hong

2016-08-01

Dentoalveolar ankylosis in growing patients is complex leading to continuing root replacement resorption, tooth infra-position, or may even affect the development of alveolar ridge and adjacent teeth. While extraction of ankylosed teeth might be associated with bone loss, decoronation of the offending tooth (removal of crown portion and instrumentation of pulp canal to stimulate bleeding) has been suggested as a more conservative approach of bone preservation until definitive implant placement is planned. To primarily assess the efficacy of bone width and height preservation around ankylosed permanent teeth following decoronation. Pubmed, Embase, Ovid Medline, Thomson's ISI Web of Science and Cochrane library were searched from the year 1984 up to May 2015. Two authors conducted the data extraction. To eliminate publication bias, Open Grey literature and Pro-quest Dissertation Abstracts and Thesis database was also consulted. Through our strict selection criteria, only 12 articles were considered for eligibility. No randomized controlled trials were identified. Only one retrospective cohort study, four case series and seven case reports, were analyzed. Following decoronation, preservation of ridge height and ridge width were both noted. To maximize the benefits of decoronation, a timely and wellmonitored intervention is required. Treatment in patients, who have surpassed pubertal growth peaks, may not yield maximum effective treatment outcomes. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Relationship between Malnutrition and the Number of Permanent Teeth in Filipino 10- to 13-Year-Olds

PubMed Central

Heinrich-Weltzien, Roswitha; Monse, Bella

2013-01-01

In the present study, we determined whether there is a delay in the eruption of permanent teeth (PT) among Filipino adolescents with stunting or thinness. Height, weight, and number of PT were recorded in 1554 Filipino 10- to 13-year-olds (711 boys; 843 girls). z-scores for height (HAZ) and body mass index (BMI) were calculated according to the WHO growth reference, and their correlations to the number of PT were assessed. 54.9% of the children have at least one form of malnutrition. Significantly, more boys (22.9%) than girls (16.5%) were thin, while no sex difference in stunting was noted (boys 48.5%; girls 44.0%). The number of PT was significantly correlated to HAZ and BMI-z-score. Stunted and thin students had significantly fewer PT than their nonaffected peers. These differences tended to be the result of delay in tooth eruption in thin and stunted adolescents. In 13-year-old girls, all PT were erupted regardless of their nutritional status indicating a catch-up. Thin and stunted boys had one tooth less than normal boys at this age. Impaired physical growth and dental development seem to have common risk factors. Therefore, regular monitoring of growth and dental development might be helpful for targeting support programmes in developing countries. PMID:24069590

Intra- and inter-tooth variation in strontium isotope ratios from prehistoric seals by laser ablation (LA)-MC-ICP-MS.

PubMed

Glykou, A; Eriksson, G; Storå, J; Schmitt, M; Kooijman, E; Lidén, K

2018-05-04

Strontium isotope ratios ( 87 Sr/ 86 Sr) in modern-day marine environments are considered to be homogeneous (~0.7092). However, in the Baltic Sea, the Sr ratios are controlled by mixing seawater and continental drainage from major rivers discharging into the Baltic. This pilot study explores if variations in Sr can be detected in marine mammals from archaeological sites in the Baltic Sea. 87 Sr/ 86 Sr ratios were measured in tooth enamel from three seal species by laser ablation (LA)-MC-ICP-MS. The method enables micro-sampling of solid materials. This is the first time that the method has been applied to marine samples from archaeological collections. The analyses showed inter-tooth 87 Sr/ 86 Sr variation suggesting that different ratios can be detected in different regions of the Baltic Sea. Furthermore, the intra-tooth variation suggests possible different geographic origin or seasonal movement of seals within different regions in the Baltic Sea through their life time. The method was successfully applied to archaeological marine samples showing that: (1) the 87 Sr/ 86 Sr ivalue n marine environments is not uniform, (2) 87 Sr/ 86 Sr differences might reflect differences in ecology and life history of different seal species, and (3) archaeological mobility studies based on 87 Sr/ 86 Sr ratio in humans should therefore be evaluated together with diet reconstruction. This article is protected by copyright. All rights reserved.

The effects of cooling systems on CO2-lased human enamel.

PubMed

Lian, H J; Lan, W H; Lin, C P

1996-12-01

The thermal effects on dentin during CO2 laser irradiation on human enamel were investigated. To simulate the clinical practice, two cooling methods (air and water spray) were applied immediately after laser exposure, whereas one group without cooling was served as control. Three hundred and sixty uniform tooth blocks were obtained from freshly extracted human third molars. Temperature change measurements were made via electrical thermocouple implanted within the tooth block 2 mm away from the enamel surface. Experimental treatments consisted of lasing without cooling, lasing with 0.5-ml/sec water cooling, and lasing with 15-psi air cooling. Our results indicated that (1) both air- and water-cooling groups could reduce temperature elevation significantly; (2) the larger power energy resulted in the higher temperature elevation. In conclusion, for CO2 laser irradiation on human enamel both water- and air-cooling methods may be effective on prevention of thermal damage of pulp.

Nutritional status and dental fluorosis among schoolchildren in communities with different drinking water fluoride concentrations in a central region in Mexico.

PubMed

Irigoyen-Camacho, M E; García Pérez, A; Mejía González, A; Huizar Alvarez, R

2016-01-15

Poor water quality and under nutrition are important factors affecting the health of many communities in developing countries. The aims of this study were: i) to describe the fluoride water concentration and the hydrogeological conditions in a region of a state located in the central in Mexico ii) to measure the association between undernutrition and dental fluorosis in children living in communities with different drinking water fluoride concentrations in a state located in the central region of Mexico. Field work was performed in the region to identify the prevailing groundwater flow characteristics and water wells were sampled to analyze water fluoride concentration. Children were selected from three communities that had different drinking water fluoride concentrations (i.e., 0.56, 0.70 and 1.60 mg/l). Fluoridated salt was available in these communities. The Thylstrup-Fejerskov Index (TFI) was used to assess dental fluorosis. Categories four or higher of this index involve changes in the entire tooth surface (ITF ≥ 4). The weight and height of the children were measured. The assessment of undernutrition was based on the World Health Organization criteria: children were classified as being at risk of low-height (Height-for-Age Z score < − 1.0 SD) and having low-height (Height-for-Age Z score < − 2.0 SD) for age and sex, the same cutoff points of the Z score were used to classify "risk of low-weight" and" low-weight children". In the region the mineralization of the water captured by the wells is the result of a reaction with volcanic materials. The water fluoride concentration in the region ranged from 0.2 to 1.6 mg/l. A total of 734 schoolchildren participated in the study. The percentage of children in fluorosis categories (ITF ≥ 4) was 15.9%, 21.1% of the children were at risk of low height-for-age, and 8.0% had low height-for-age. The percentage of children with fluorosis (ITF ≥ 4) was 6.3%, 9.1% and 31.9% (p ˂ 0.001) and low high-for-age was 2.9%, 2.5% and 8.4% (p ˂ 0.001), for the communities with F concentrations of 0.56 mg/l, 0.70 mg/l and 1.6 mg/l, respectively. The logistic regression model showed an association between dental fluorosis (TFI ≥ 4) and low height-for-age (OR 2.09, p = 0.022) after adjusting for sex, number of teeth erupted, source of drinking water, use of fluoridated toothpaste and tap water fluoride concentration in the community. Children with low height-for-age were more likely to have dental fluorosis in the TFI categories that affect the entire tooth surface. The results suggest that subpopulations with chronic undernutrition are more susceptible to dental fluorosis.

The thermal influence of continents on a model-generated January climate

NASA Technical Reports Server (NTRS)

Spar, J.; Cohen, C.; Wu, P.

1981-01-01

Two climate simulations were compared. Both climate computations were initialized with the same horizontally uniform state of rest. However, one is carried out on a water planet (without continents), while the second is repeated on a planet with geographically realistic but flat (sea level) continents. The continents in this experiment have a uniform albedo of 0.14, except where snow accumulates, a uniform roughness height of 0.3 m, and zero water storage capacity. Both runs were carried out for a 'perpetual January' with solar declination fixed at January 15.

Piezoelectric effect in non-uniform strained carbon nanotubes

NASA Astrophysics Data System (ADS)

Ilina, M. V.; Blinov, Yu F.; Ilin, O. I.; Rudyk, N. N.; Ageev, O. A.

2017-10-01

The piezoelectric effect in non-uniform strained carbon nanotubes (CNTs) has been studied. It is shown that the magnitude of strained CNTs surface potential depends on a strain value. It is established that the resistance of CNT also depends on the strain and internal electric field, which leads to the hysteresis in the current-voltage characteristics. Analysis of experimental studies of the non-uniform strained CNT with a diameter of 92 nm and a height of 2.1 μm allowed us to estimate the piezoelectric coefficient 0.107 ± 0.032 C/m2.

Digital tooth-based superimposition method for assessment of alveolar bone levels on cone-beam computed tomography images.

PubMed

Romero-Delmastro, Alejandro; Kadioglu, Onur; Currier, G Frans; Cook, Tanner

2014-08-01

Cone-beam computed tomography images have been previously used for evaluation of alveolar bone levels around teeth before, during, and after orthodontic treatment. Protocols described in the literature have been vague, have used unstable landmarks, or have required several software programs, file conversions, or hand tracings, among other factors that could compromise the precision of the measurements. The purposes of this article are to describe a totally digital tooth-based superimposition method for the quantitative assessment of alveolar bone levels and to evaluate its reliability. Ultra cone-beam computed tomography images (0.1-mm reconstruction) from 10 subjects were obtained from the data pool of the University of Oklahoma; 80 premolars were measured twice by the same examiner and a third time by a second examiner to determine alveolar bone heights and thicknesses before and more than 6 months after orthodontic treatment using OsiriX (version 3.5.1; Pixeo, Geneva, Switzerland). Intraexaminer and interexaminer reliabilities were evaluated, and Dahlberg's formula was used to calculate the error of the measurements. Cross-sectional and longitudinal evaluations of alveolar bone levels were possible using a digital tooth-based superimposition method. The mean differences for buccal alveolar crest heights and thicknesses were below 0.10 mm for the same examiner and below 0.17 mm for all examiners. The ranges of errors for any measurement were between 0.02 and 0.23 mm for intraexaminer errors, and between 0.06 and 0.29 mm for interexaminer errors. This protocol can be used for cross-sectional or longitudinal assessment of alveolar bone levels with low interexaminer and intraexaminer errors, and it eliminates the use of less reliable or less stable landmarks and the need for multiple software programs and image printouts. Standardization of the methods for bone assessment in orthodontics is necessary; this method could be the answer to this need. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Correlations between In Situ Conductivity and Uniform-Height Epitaxial Morphology in Pb / Si ( 1 1 1 ) ₋ ( 7 × 7 )

DOE PAGES

Jałochowski, M.; Zdyb, R.; Tringides, M. C.

2016-02-23

The growth of Pb on Si(111)-7x7 at temperatures from 72 K to 201 K has been investigated using in situ electrical resistivity measurements and Scanning Tunneling Microscopy (STM). For temperatures T>140 K the specific resistivity ρ(θ) vs coverage θ shows an unusual "hump", instead of the expected monotonic decrease with θ. This novel result correlates well with the formation of uniform height 8-layer Pb islands and the superdiffusive motion of the wetting layer, despite the low temperatures. A model of the film resistivity as two resistors in series, the amorphous wetting layer and the crystalline islands, explains quantitatively the resistivitymore » dependence on θ.« less

Influence of photoactivation method and mold for restoration on the Knoop hardness of resin composite restorations.

PubMed

Brandt, William Cunha; Silva-Concilio, Lais Regiane; Neves, Ana Christina Claro; de Souza-Junior, Eduardo Jose Carvalho; Sinhoreti, Mario Alexandre Coelho

2013-09-01

The aim of this study was to evaluate in vitro the Knoop hardness in the top and bottom of composite photo activated by different methods when different mold materials were used. Z250 (3M ESPE) and XL2500 halogen unit (3M ESPE) were used. For hardness test, conical restorations were made in extracted bovine incisors (tooth mold) and also metal mold (approximately 2 mm top diameter × 1.5 mm bottom diameter × 2 mm in height). Different photoactivation methods were tested: high-intensity continuous (HIC), low-intensity continuous (LIC), soft-start, or pulse-delay (PD), with constant radiant exposure. Knoop readings were performed on top and bottom restoration surfaces. Data were submitted to two-way ANOVA and Tukey's test (p = 0.05). On the top, regardless of the mold used, no significant difference in the Knoop hardness (Knoop hardness number, in kilograms-force per square millimeter) was observed between the photoactivation methods. On the bottom surface, the photoactivation method HIC shows higher means of hardness than LIC when tooth and metal were used. Significant differences of hardness on the top and in the bottom were detected between tooth and metal. The photoactivation method LIC and the material mold can interfere in the hardness values of composite restorations.

Large Eddy Simulations of a Bottom Boundary Layer Under a Shallow Geostrophic Front

NASA Astrophysics Data System (ADS)

Bateman, S. P.; Simeonov, J.; Calantoni, J.

2017-12-01

The unstratified surf zone and the stratified shelf waters are often separated by dynamic fronts that can strongly impact the character of the Ekman bottom boundary layer. Here, we use large eddy simulations to study the turbulent bottom boundary layer associated with a geostrophic current on a stratified shelf of uniform depth. The simulations are initialized with a spatially uniform vertical shear that is in geostrophic balance with a pressure gradient due to a linear horizontal temperature variation. Superposed on the temperature front is a stable vertical temperature gradient. As turbulence develops near the bottom, the turbulence-induced mixing gradually erodes the initial uniform temperature stratification and a well-mixed layer grows in height until the turbulence becomes fully developed. The simulations provide the spatial distribution of the turbulent dissipation and the Reynolds stresses in the fully developed boundary layer. We vary the initial linear stratification and investigate its effect on the height of the bottom boundary layer and the turbulence statistics. The results are compared to previous models and simulations of stratified bottom Ekman layers.

Dental Fear in Children with Repeated Tooth Injuries.

PubMed

Negovetić Vranić, Dubravka; Ivančić Jokić, Nataša; Bakarčić, Danko; Carek, Andreja; Rotim, Željko; Verzak, Željko

2016-06-01

Tooth injuries are serious clinical conditions. Some children experience dental trauma only once, while others are more prone to repeated tooth injuries. Repeated dental trauma occurs in 19.4% to 30% of patients. Pain and dental trauma are the most common reasons for fear and anxiety. The main objective of this study was to investigate how dental trauma, as well as repeated dental trauma affects the occurrence and development of dental fear in children. The study was conducted on a random sample of 147 subjects (88 boys and 59 girls) aged 5-8 and 9-12 years. Subjects in both age groups were divided into subroups without dental trauma, with one dental trauma and with repeated dental trauma. The validated Children’s Fear Survey Schedule – Dental Subscale was used on fear assessment. Results showed that only 12.2% of children without trauma, 33.3% with one trauma and 51.7% with repeated trauma were not afraid of injection. Older children had a significantly lower fear of injections, touch of an unknown person, choking, going to the hospital and people in white uniforms. Dentist was not the cause of fear in 65.5% of patients with repeated trauma. With each repeated injury of teeth, the degree of their fear of dental treatment was lower.

The inter-relationship between dietary and environmental properties and tooth wear: comparisons of mesowear, molar wear rate, and hypsodonty index of extant Sika deer populations.

PubMed

Kubo, Mugino Ozaki; Yamada, Eisuke

2014-01-01

In reference to the evolutionary trend of increasing cheek tooth height in herbivorous ungulates, the causes of dental abrasion have long been debated. Interspecific comparisons of extant ungulates have revealed that both phytoliths in grass and external abrasive matter may play important roles. Using analysis of extant sika deer living in various environments and showing continuous latitudinal variation in food habits from northern grazing to southern browsing, we quantitatively evaluated the influence of dietary and environmental properties on three dental variables: mesowear score (MS), molar wear rate, and M3 hypsodonty index. We used 547 skulls and 740 mandibles from 16 populations of sika deer to obtain the dental measurements. We found that only graminoid proportion in diet correlated with MS and the molar wear rate, implying that phytoliths in grass abrade dental tissues. In contrast, annual precipitation in habitat was not correlated with any of the dental variables. We also found a significant correlation between the molar wear rate (selective pressure for high-crowned molars) and the M3 hypsodonty index of extant sika deer, implying an evolutionary increment in molar height corresponding to the molar wear rate. Our intraspecific comparative analyses provide further support for use of mesowear analysis as a paleodiet estimation method; it not only reveals staple food types (graminoids or dicots) but also implies regional or seasonal variation in the diet of the species.

The Inter-Relationship between Dietary and Environmental Properties and Tooth Wear: Comparisons of Mesowear, Molar Wear Rate, and Hypsodonty Index of Extant Sika Deer Populations

PubMed Central

Kubo, Mugino Ozaki; Yamada, Eisuke

2014-01-01

In reference to the evolutionary trend of increasing cheek tooth height in herbivorous ungulates, the causes of dental abrasion have long been debated. Interspecific comparisons of extant ungulates have revealed that both phytoliths in grass and external abrasive matter may play important roles. Using analysis of extant sika deer living in various environments and showing continuous latitudinal variation in food habits from northern grazing to southern browsing, we quantitatively evaluated the influence of dietary and environmental properties on three dental variables: mesowear score (MS), molar wear rate, and M3 hypsodonty index. We used 547 skulls and 740 mandibles from 16 populations of sika deer to obtain the dental measurements. We found that only graminoid proportion in diet correlated with MS and the molar wear rate, implying that phytoliths in grass abrade dental tissues. In contrast, annual precipitation in habitat was not correlated with any of the dental variables. We also found a significant correlation between the molar wear rate (selective pressure for high-crowned molars) and the M3 hypsodonty index of extant sika deer, implying an evolutionary increment in molar height corresponding to the molar wear rate. Our intraspecific comparative analyses provide further support for use of mesowear analysis as a paleodiet estimation method; it not only reveals staple food types (graminoids or dicots) but also implies regional or seasonal variation in the diet of the species. PMID:24603896

Improving the side-to-side stapled anastomosis: comparison of staplers for robust crotch formation.

PubMed

Kimura, Masahiro; Kuwabara, Yoshiyuki; Taniwaki, Satoshi; Mitsui, Akira; Shibata, Yasuyuki; Ueno, Shuhei

2018-01-01

Few studies have investigated the burst pressure of side-to-side anastomoses comparing different stapling devices that are commercially available. We conducted side-to-side anastomoses with a variety of staplers and compared burst pressure in the crotch of the anastomoses. Nagoya City East Medical Center. We conducted side-to-side anastomoses with 9 staplers with different shapes and forms. Fresh pig small intestines were used. A side-to-side anastomosis was performed between 2 intestine specimens using a linear stapler. The burst pressure of the anastomosis was recorded. In total, 45 staplers were used for this experiment. The site of leakage in all cases was the crotch. Regarding the influence of the number of staple rows, the burst pressure in 3-row staplers was significantly higher than in 2-row staplers. With regard to the relationship between staple height and burst pressure, staples with a height slightly shorter than the intestinal thickness showed the highest burst pressure. In a comparison of staplers with uniform staple heights and stamplers with staples of 3 different heights, the latter had significantly lower burst pressures. Neoveil significantly increased the burst pressure in the crotch and contributed to the highest burst pressure of all the staplers used in this experiment. In this experiment, we defined the important factors that influence burst pressure at the crotch of a stapled, side-to-side anastomosis. These factors include the number of staple rows, the height of the staple compared with the thickness of the tissue, uniformity of staple height, and reinforcement of the staple line. In any surgical case requiring intestinal anastomosis, selection of a stapler is a critical step. Copyright © 2017 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.

Impact of birth characteristics, breast feeding and vital statistics on the eruption of primary teeth among healthy infants in Saudi Arabia: an observational study.

PubMed

Alnemer, Kholoud Abdullah; Pani, Sharat Chandra; Althubaiti, Alaa M; Bawazeer, Manal

2017-12-15

This study aimed to explore the impact of gender, birth weight, maternal age, type of delivery, gestational age and feeding practices on the eruption of teeth in children with no underlying medical conditions or developmental defects in their first year of life. A cross-sectional observational study design was used. A primary healthcare setting in Riyadh, Saudi Arabia. All children in their first year of life attending a vaccination clinic (n=422) were included in the study. Infants with chronic childhood illnesses, those who were below the 5th percentile in height or weight, infants with congenital birth defects and chronic illnesses, infants who were born preterm and low birth weight infants were excluded from the study. The type of delivery, birth weight, age of mother, height and weight percentile for age (as plotted on the WHO growth chart for infants) and feeding practices were recorded by the examiner, and this was followed by a clinical examination to determine the presence or absence of each tooth. Regression models were developed to determine the effect of the different variables on the presence of primary teeth. There was a significant association between the weight percentile of the child (adjusted for age) and the number of erupted primary teeth, suggesting that heavier children have an earlier eruption of teeth. No association was observed between birth weight, height percentile for age or maternal age at the time of birth and the number of erupted primary teeth. Children who were exclusively breast fed were significantly more likely to have an erupted first primary tooth earlier than non-breastfed group. Breast feeding and the weight of the child may have an influence on the eruption of primary teeth in the first year of life. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A new distinctively banded-species of Panaqolus (Siluriformes: Loricariidae) from the western Amazon Basin in Peru.

PubMed

Lujan, Nathan K; Steele, Sarah; Velasquez, Miquel

2013-01-01

Panaqolus albivermis is described as a new species based on four specimens from the San Alejandro River, a tributary of the upper Ucayali River in central Peru. Panaqolus albivermis is diagnosed from all other Panaqolus except P. maccus by having head, body, and fins with widely separated small white to yellow spots, vermiculations, and/or thin oblique bands on a black base (vs. exclusively small white to yellow spots on a black base in P. alboinaculatus, generally broad oblique bands of alternating light to dark brown in P. changae, P. gnomus, P purusiensis, and a uniformly dark gray to black body color in P. dentex, P. koko, and P. nocturnus); P. albivernis can be diagnosed from P. maccus by having a black base color (vs. brown), by having parallel dentary tooth cups (vs. acute intermandibular tooth cup angle), and by having a larger known adult body size (95.8 mm SL vs. 84.8).

Clinical tooth preparations and associated measuring methods: a systematic review.

PubMed

Tiu, Janine; Al-Amleh, Basil; Waddell, J Neil; Duncan, Warwick J

2015-03-01

The geometries of tooth preparations are important features that aid in the retention and resistance of cemented complete crowns. The clinically relevant values and the methods used to measure these are not clear. The purpose of this systematic review was to retrieve, organize, and critically appraise studies measuring clinical tooth preparation parameters, specifically the methodology used to measure the preparation geometry. A database search was performed in Scopus, PubMed, and ScienceDirect with an additional hand search on December 5, 2013. The articles were screened for inclusion and exclusion criteria and information regarding the total occlusal convergence (TOC) angle, margin design, and associated measuring methods were extracted. The values and associated measuring methods were tabulated. A total of 1006 publications were initially retrieved. After removing duplicates and filtering by using exclusion and inclusion criteria, 983 articles were excluded. Twenty-three articles reported clinical tooth preparation values. Twenty articles reported the TOC, 4 articles reported margin designs, 4 articles reported margin angles, and 3 articles reported the abutment height of preparations. A variety of methods were used to measure these parameters. TOC values seem to be the most important preparation parameter. Recommended TOC values have increased over the past 4 decades from an unachievable 2- to 5-degree taper to a more realistic 10 to 22 degrees. Recommended values are more likely to be achieved under experimental conditions if crown preparations are performed outside of the mouth. We recommend that a standardized measurement method based on the cross sections of crown preparations and standardized reporting be developed for future studies analyzing preparation geometry. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Reporting numeric values of complete crowns. Part 1: Clinical preparation parameters.

PubMed

Tiu, Janine; Al-Amleh, Basil; Waddell, J Neil; Duncan, Warwick J

2015-07-01

An implemented objective measuring system for measuring clinical tooth preparations does not exist. The purpose of this study was to compare clinically achieved tooth preparations for ceramic crowns by general dentists with the recommended values in the literature with an objective measuring method. Two hundred thirty-six stone dies prepared for anterior and posterior complete ceramic crown restorations (IPS e.max Press; Ivoclar Vivadent) were collected from dental laboratories. The dies were scanned and analyzed using the coordinate geometry method. Cross-sectioned images were captured, and the average total occlusal convergence angle, margin width, and abutment height for each preparation was measured and presented with associated 95% confidence intervals. The average total occlusal convergence angles for each tooth type was above the recommended values reported in the literature. The average margin widths (0.40 to 0.83 mm) were below the minimum recommended values (1 to 1.5 mm). The tallest preparations were maxillary canines (5.25 mm), while the shortest preparations were mandibular molars (1.87 mm). Complete crown preparations produced in general practice do not achieve the recommended values found in the literature. However, these recommended values are not based on clinical trials, and the effects of observed shortfalls on the clinical longevity of these restorations are not predictable. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Genome-Wide Association Study Identifies Four Loci Associated with Eruption of Permanent Teeth

PubMed Central

Zhang, Hao; Shaffer, John R.; Hansen, Thomas; Esserlind, Ann-Louise; Boyd, Heather A.; Nohr, Ellen A.; Timpson, Nicholas J.; Fatemifar, Ghazaleh; Paternoster, Lavinia; Evans, David M.; Weyant, Robert J.; Levy, Steven M.; Lathrop, Mark; Smith, George Davey; Murray, Jeffrey C.; Olesen, Jes; Werge, Thomas; Marazita, Mary L.; Sørensen, Thorkild I. A.; Melbye, Mads

2011-01-01

The sequence and timing of permanent tooth eruption is thought to be highly heritable and can have important implications for the risk of malocclusion, crowding, and periodontal disease. We conducted a genome-wide association study of number of permanent teeth erupted between age 6 and 14 years, analyzed as age-adjusted standard deviation score averaged over multiple time points, based on childhood records for 5,104 women from the Danish National Birth Cohort. Four loci showed association at P<5×10−8 and were replicated in four independent study groups from the United States and Denmark with a total of 3,762 individuals; all combined P-values were below 10−11. Two loci agreed with previous findings in primary tooth eruption and were also known to influence height and breast cancer, respectively. The two other loci pointed to genomic regions without any previous significant genome-wide association study results. The intronic SNP rs7924176 in ADK could be linked to gene expression in monocytes. The combined effect of the four genetic variants was most pronounced between age 10 and 12 years, where children with 6 to 8 delayed tooth eruption alleles had on average 3.5 (95% confidence interval: 2.9–4.1) fewer permanent teeth than children with 0 or 1 of these alleles. PMID:21931568

An experimental evaluation of precision laser cutting of dental hard tissues and materials.

PubMed

Cox, C J; Patel, B C; Pearson, G J

1993-06-01

This paper examines the use of excimer laser radiation in the controlled removal of tooth tissue and three plastic restorative materials. Freshly extracted human third molar teeth were filled with three restorative materials and sectioned longitudinally through the restoratives. The cut surfaces of the materials and surrounding enamel and dentine were exposed to three laser energy densities and the dimensions and topographical details of the irradiated sites assessed using optical and scanning electron microscopy. The results showed that the radiation produced lesions of uniformly reproducible size and shape.

Contrastive analysis of cooling performance between a high-level water collecting cooling tower and a typical cooling tower

NASA Astrophysics Data System (ADS)

Wang, Miao; Wang, Jin; Wang, Jiajin; Shi, Cheng

2018-02-01

A three-dimensional (3D) numerical model is established and validated for cooling performance optimization between a high-level water collecting natural draft wet cooling tower (HNDWCT) and a usual natural draft wet cooling tower (UNDWCT) under the actual operation condition at Wanzhou power plant, Chongqing, China. User defined functions (UDFs) of source terms are composed and loaded into the spray, fill and rain zones. Considering the conditions of impact on three kinds of corrugated fills (Double-oblique wave, Two-way wave and S wave) and four kinds of fill height (1.25 m, 1.5 m, 1.75 m and 2 m), numerical simulation of cooling performance are analysed. The results demonstrate that the S wave has the highest cooling efficiency in three fills for both towers, indicating that fill characteristics are crucial to cooling performance. Moreover, the cooling performance of the HNDWCT is far superior to that of the UNDWCT with fill height increases of 1.75 m and above, because the air mass flow rate in the fill zone of the HNDWCT improves more than that in the UNDWCT, as a result of the rain zone resistance declining sharply for the HNDWCT. In addition, the mass and heat transfer capacity of the HNDWCT is better in the tower centre zone than in the outer zone near the tower wall under a uniform fill layout. This behaviour is inverted for the UNDWCT, perhaps because the high-level collection devices play the role of flow guiding in the inner zone. Therefore, when non-uniform fill layout optimization is applied to the HNDWCT, the inner zone increases in height from 1.75 m to 2 m, the outer zone reduces in height from 1.75 m to 1.5 m, and the outlet water temperature declines approximately 0.4 K compared to that of the uniform layout.

New reversing design method for LED uniform illumination.

PubMed

Wang, Kai; Wu, Dan; Qin, Zong; Chen, Fei; Luo, Xiaobing; Liu, Sheng

2011-07-04

In light-emitting diode (LED) applications, it is becoming a big issue that how to optimize light intensity distribution curve (LIDC) and design corresponding optical component to achieve uniform illumination when distance-height ratio (DHR) is given. A new reversing design method is proposed to solve this problem, including design and optimization of LIDC to achieve high uniform illumination and a new algorithm of freeform lens to generate the required LIDC by LED light source. According to this method, two new LED modules integrated with freeform lenses are successfully designed for slim direct-lit LED backlighting with thickness of 10mm, and uniformities of illuminance increase from 0.446 to 0.915 and from 0.155 to 0.887 when DHRs are 2 and 3 respectively. Moreover, the number of new LED modules dramatically decreases to 1/9 of the traditional LED modules while achieving similar uniform illumination in backlighting. Therefore, this new method provides a practical and simple way for optical design of LED uniform illumination when DHR is much larger than 1.

Metalclad Airship Hull Study. Volume 1 and Volume 2

DTIC Science & Technology

1976-12-01

37.5% weight saving of the hull skin with a maximim pressure of 8.75 in. of water column and maximum-minimum pressure ratio still at comfortable 3.5. The...overall height of 118.98 in.to no more than 100.Oin. with considerable weight saving . Instead of the geometrical height of main frames equal to (.108...changed slightly to obtain uniform spacing. This has negligible effect on the result, but saves a considerable analysis timie. For the purpose of this

Maxillary Interdental Osteotomies Have Low Morbidity for Alveolar Crestal Bone and Adjacent Teeth: A Cone Beam Computed Tomography-Based Study.

PubMed

Rodrigues, Daniel B; Campos, Paulo S F; Wolford, Larry M; Ignácio, Jaqueline; Gonçalves, João R

2018-02-19

Maxillary segmentation involving interdental osteotomies can have an adverse effect on the interdental crestal bone and adjacent teeth. The purpose of the present study was to evaluate the effect of interdental osteotomies on surrounding osseous and dental structures, including adjacent teeth, using cone beam computed tomography (CBCT), in patients who underwent segmental maxillary osteotomies. The present retrospective cohort study evaluated interdental osteotomy (IDO) sites between the lateral incisors and canines in patients treated with 3-piece Le Fort I osteotomies. CBCT scans were assessed using Kodac Dental Imaging software at specific intervals: T0 (before surgery), T1 (immediately after surgery), and T2 (a minimum of 11 months after surgery). The statistical analysis using a linear regression model was adjusted to compare the variables at the different intervals. Injury to the dental structures was assessed by radiological evidence of dental damage, the requirement for endodontic treatment, or tooth loss. We evaluated 94 IDO sites in 47 patients in the present study. The mean inter-radicular distance at T0 was 2.5 mm. A statistically significant increase was seen in the inter-radicular distance (between T1 and T0) of 0.72 mm, with a reduction of the alveolar bone crest height (between T2 and T0) of 0.19 mm (P < .001) for the group that underwent IDO. A weak correlation was found for this increase in the inter-radicular distance, with changes in the alveolar crest bone height. The potential complications associated with interdental osteotomies such as iatrogenic damage to the tooth structure, the need for endodontic treatment, and tooth loss were not encountered in any patients. We found very low morbidity for the interdental alveolar crest and the integrity of teeth adjacent to interdental osteotomies for patients who underwent maxillary segmentation between the lateral incisors and canines. Copyright © 2018 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

The extension of a uniform canopy reflectance model to include row effects

NASA Technical Reports Server (NTRS)

Suits, G. H. (Principal Investigator)

1981-01-01

The effect of row structure is assumed to be caused by the variation in density of vegetation across rows rather than to a profile in canopy height. The calculation of crop reflectance using vegetation density modulation across rows follows a parallel procedure to that for a uniform canopy. Predictions using the row model for wheat show that the effect of changes in sun to row azimuth are greatest in Landsat Band 5 (red band) and can result in underestimation of crop vigor.

Applications of cone-beam computed tomography to assess the effects of labial crown morphologies and collum angles on torque for maxillary anterior teeth.

PubMed

Kong, Wei-Dong; Ke, Jun-Yu; Hu, Xiang-Quan; Zhang, Wu; Li, Shu-Shu; Feng, Yi

2016-11-01

Currently, cone-beam computed tomography (CBCT) has been widely used because of its capacity to evaluate the anatomic structures of the maxilla, mandible, and teeth in 3 dimensions. However, articles about the use of CBCT to evaluate the relationships between the morphology of individual teeth and torque expression remain rare. In this study, we aimed to determine the influence of labial crown morphologies and collum angles on torque for maxillary anterior teeth using CBCT. A total of 206 extracted maxillary anterior teeth were selected to establish scanning models using dental wax, and they were scanned by CBCT. Three-dimensionally reconstructed images and median sagittal sections of the teeth were digitized and analyzed with AutoCAD software (Autodesk, San Rafael, Calif). The angle α, formed by the intersection of the tangent at a certain vertical height on the labial surface from the incisal edge with the crown long axis, and the collum angle, were measured. The variations in angle α at different heights from the incisal edge for the same type of tooth were statistically significantly different (P <0.001). Moreover, the variations between collum angles and 0° for any type of maxillary anterior tooth were statistically significant (P <0.01). This study suggested that there are great differences in labial crown morphologies and collum angles for maxillary anterior teeth between persons, indicating that the morphologies of these teeth do play important roles in torque variations. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Applicability of Cameriere's and Drusini's age estimation methods to a sample of Turkish adults.

PubMed

Hatice, Boyacioglu Dogru; Nihal, Avcu; Nursel, Akkaya; Humeyra Ozge, Yilanci; Goksuluk, Dincer

2017-10-01

The aim of this study was to investigate the applicability of Drusini's and Cameriere's methods to a sample of Turkish people. Panoramic images of 200 individuals were allocated into two groups as study and test groups and examined by two observers. Tooth coronal indexes (TCI), which is the ratio between coronal pulp cavity height and crown height, were calculated in the mandibular first and second premolars and molars. Pulp/tooth area ratios (ARs) were calculated in the maxillary and mandibular canine teeth. Study group measurements were used to derive a regression model. Test group measurements were used to evaluate the accuracy of the regression model. Pearson's correlation coefficients and regression analysis were used. The correlations between TCIs and age were -0.230, -0.301, -0.344 and -0.257 for mandibular first premolar, second premolar, first molar and second molar, respectively. Those for the maxillary canine (MX) and mandibular canine (MN) ARs were -0.716 and -0.514, respectively. The MX ARs were used to build the linear regression model that explained 51.2% of the total variation, with a standard error of 9.23 years. The mean error of the estimates in test group was 8 years and age of 64% of the individuals were estimated with an error of <±10 years which is acceptable in forensic age prediction. The low correlation coefficients between age and TCI indicate that Drusini's method was not applicable to the estimation of age in a Turkish population. Using Cameriere's method, we derived a regression model.

Study of elastomeric bearings for superelevated U-Beam bridges.

DOT National Transportation Integrated Search

2009-10-01

The primary objective of this research was to determine the best way to consider the effects of transverse : superelevation on uniform-height steel-reinforced elastomeric bearing pads for U-Beam bridges. Existing TxDOT : design provisions did not spe...

Combined effects of total grain-size distribution and crosswind on the rise of eruptive volcanic columns

NASA Astrophysics Data System (ADS)

Girault, F.; Carazzo, G.; Tait, S.; Kaminski, E.

2016-10-01

The maximum height of an explosive volcanic column, H, depends on the 1/4th power of the eruptive mass flux, Q, and on the 3/4th power of the stratification of the atmosphere, N. Expressed as scaling laws, this relationship has made H a widely used proxy to estimate Q. Two additional effects are usually included to produce more accurate and robust estimates of Q based on H: particle sedimentation from the volcanic column, which depends on the total grain-size distribution (TGSD) and the atmospheric crosswind. Both coarse TGSD and strong crosswind have been shown to decrease strongly the maximum column height, and TGSD, which also controls the effective gas content in the column, influences the stability of the column. However, the impact of TGSD and of crosswind on the dynamics of the volcanic column are commonly considered independently. We propose here a steady-state 1D model of an explosive volcanic column rising in a windy atmosphere that explicitly accounts for particle sedimentation and wind together. We consider three typical wind profiles: uniform, linear, and complex, with the same maximum wind velocity of 15 m s- 1. Subject to a uniform wind profile, the calculations show that the maximum height of the plume strongly decreases for any TGSD. The effect of TGSD on maximum height is smaller for uniform and complex wind profiles than for a linear profile or without wind. The largest differences of maximum heights arising from different wind profiles are observed for the largest source mass fluxes (> 107 kg s- 1) for a given TGSD. Compared to no wind conditions, the field of column collapse is reduced for any wind profile and TGSD at the vent, an effect that is the strongest for small mass fluxes and coarse TGSD. Provided that the maximum plume height and the wind profile are known from real-time observations, the model predicts the mass discharge rate feeding the eruption for a given TGSD. We apply our model to a set of eight historical volcanic eruptions for which all the required information is known. Taking into account the measured wind profile and the actual TGSD at the vent substantially improves (by ≈ 30%) the agreement between the mass discharge rate calculated from the model based on plume height and the field observation of deposit mass divided by eruption duration, relative to a model taking into account TGSD only. This study contributes to the improvement of the characterization of volcanic source term required as input to larger scale models of ash and aerosol dispersion.

Lack of association between allozyme heterozygosity and juvenile traits in Eucalyptus

USDA-ARS?s Scientific Manuscript database

Genetic variability for juvenile waits, which included basal diameter, height, biomass accumulation, and growth increment, was studied in eight provenances involving four species, Eucalyptus grandis, E. saligna, E. camaldulensis and E. urophylla, under uniform greenhouse conditions. The species diff...

Crystal Structure of a Modulated Composite Structure with Two Subsystems: Ba 1.1064CoO 3

NASA Astrophysics Data System (ADS)

El Abed, A.; Elqebbaj, S. E.; Zakhour, M.; Champeaux, M.; Perez-Mato, J. M.; Darriet, J.

2001-11-01

The structure of Ba1.1064CoO3 has been solved in the (3+1)-dimensional formalism. The structure is described as a modulated chain composite with two subsystems, [CoO3] and [Ba], respectively. The superspace group is R-3m(00γ)0s with a=9.8842(20) Å, c=2.4785(12) Å, and q=0.5532(4) c* (Z=3). A saw-tooth function was used to model both the occupational and displacive modulations. Each atomic saw-tooth function is defined by its center ○4 along the fourth dimension, its width (Δ), and the maximum amplitude of the displacive modulation (δ). The paper describes how, as a first approximation, the columns (CoO3) can be mainly described by a single free parameter, based on the height difference of the trigonal prisms and octahedra that constitute the transition metal chains. As a result, this superspace formalism requires only a small number of variables to be refined, compared to the conventional superstructure description.

Resonances and wave propagation velocity in the subglottal airways.

PubMed

Lulich, Steven M; Alwan, Abeer; Arsikere, Harish; Morton, John R; Sommers, Mitchell S

2011-10-01

Previous studies of subglottal resonances have reported findings based on relatively few subjects, and the relations between these resonances, subglottal anatomy, and models of subglottal acoustics are not well understood. In this study, accelerometer signals of subglottal acoustics recorded during sustained [a:] vowels of 50 adult native speakers (25 males, 25 females) of American English were analyzed. The study confirms that a simple uniform tube model of subglottal airways, closed at the glottis and open at the inferior end, is appropriate for describing subglottal resonances. The main findings of the study are (1) whereas the walls may be considered rigid in the frequency range of Sg2 and Sg3, they are yielding and resonant in the frequency range of Sg1, with a resulting ~4/3 increase in wave propagation velocity and, consequently, in the frequency of Sg1; (2) the "acoustic length" of the equivalent uniform tube varies between 18 and 23.5 cm, and is approximately equal to the height of the speaker divided by an empirically determined scaling factor; (3) trachea length can also be predicted by dividing height by another empirically determined scaling factor; and (4) differences between the subglottal resonances of males and females can be accounted for by height-related differences. © 2011 Acoustical Society of America

Wind-Tunnel Simulation of Weakly and Moderately Stable Atmospheric Boundary Layers

NASA Astrophysics Data System (ADS)

Hancock, Philip E.; Hayden, Paul

2018-07-01

The simulation of horizontally homogeneous boundary layers that have characteristics of weakly and moderately stable atmospheric flow is investigated, where the well-established wind engineering practice of using `flow generators' to provide a deep boundary layer is employed. Primary attention is given to the flow above the surface layer, in the absence of an overlying inversion, as assessed from first- and second-order moments of velocity and temperature. A uniform inlet temperature profile ahead of a deep layer, allowing initially neutral flow, results in the upper part of the boundary layer remaining neutral. A non-uniform inlet temperature profile is required but needs careful specification if odd characteristics are to be avoided, attributed to long-lasting effects inherent of stability, and to a reduced level of turbulent mixing. The first part of the wind-tunnel floor must not be cooled if turbulence quantities are to vary smoothly with height. Closely horizontally homogeneous flow is demonstrated, where profiles are comparable or closely comparable with atmospheric data in terms of local similarity and functions of normalized height. The ratio of boundary-layer height to surface Obukhov length, and the surface heat flux, are functions of the bulk Richardson number, independent of horizontal homogeneity. Surface heat flux rises to a maximum and then decreases.

Wind-Tunnel Simulation of Weakly and Moderately Stable Atmospheric Boundary Layers

NASA Astrophysics Data System (ADS)

Hancock, Philip E.; Hayden, Paul

2018-02-01

The simulation of horizontally homogeneous boundary layers that have characteristics of weakly and moderately stable atmospheric flow is investigated, where the well-established wind engineering practice of using `flow generators' to provide a deep boundary layer is employed. Primary attention is given to the flow above the surface layer, in the absence of an overlying inversion, as assessed from first- and second-order moments of velocity and temperature. A uniform inlet temperature profile ahead of a deep layer, allowing initially neutral flow, results in the upper part of the boundary layer remaining neutral. A non-uniform inlet temperature profile is required but needs careful specification if odd characteristics are to be avoided, attributed to long-lasting effects inherent of stability, and to a reduced level of turbulent mixing. The first part of the wind-tunnel floor must not be cooled if turbulence quantities are to vary smoothly with height. Closely horizontally homogeneous flow is demonstrated, where profiles are comparable or closely comparable with atmospheric data in terms of local similarity and functions of normalized height. The ratio of boundary-layer height to surface Obukhov length, and the surface heat flux, are functions of the bulk Richardson number, independent of horizontal homogeneity. Surface heat flux rises to a maximum and then decreases.

Influence of local parameters on the dispersion of traffic-related pollutants within street canyons

NASA Astrophysics Data System (ADS)

Karra, Styliani; Malki-Epshtein, Liora; Martin Hyde Collaboration

2011-11-01

Ventilation within urban cities and street canyons and the associated air quality is a problem of increasing interest in the last decades. It is important for to minimise exposure of the population to traffic-related pollutants at street level. The residence time of pollutants within the street canyons depends on the meteorological conditions such as wind speed and direction, geometry layout and local parameters (position of traffic lane within the street). An experimental study was carried out to investigate the influence of traffic lane position on the dispersion of traffic-related pollutants within different street canyons geometries: symmetrical (equal building heights on both sides of the street), non-symmetrical (uniform building heights but lower on one side of the street) and heterogeneous (non-uniform building heights on both sides of the street) under constant meteorological conditions. Laboratory experiments were carried out within a water channel and simultaneous measurements of velocity field and concentration scalar levels within and above the street canyons using PIV and PLIF techniques. Traffic -related emissions were simulated using a line emission source. Two positions were examined for all street geometries: line emission source was placed in the centre of the street canyon; line emission source was placed off the centre of the street. TSI Incorporated.

Non-uniform binding of single-stranded DNA binding proteins to hybrids of single-stranded DNA and single-walled carbon nanotubes observed by atomic force microscopy in air and in liquid

NASA Astrophysics Data System (ADS)

Umemura, Kazuo; Ishizaka, Kei; Nii, Daisuke; Izumi, Katsuki

2016-12-01

Using atomic force spectroscopy (AFM), we observed hybrids of single-stranded DNA (ssDNA) and single-walled carbon nanotubes (SWNTs) with or without protein molecules in air and in an aqueous solution. This is the first report of ssDNA-SWNT hybrids with proteins in solution analyzed by AFM. In the absence of protein, the height of the ssDNA-SWNT hybrids was 1.1 ± 0.3 nm and 2.4 ± 0.6 nm in air and liquid, respectively, suggesting that the ssDNA molecules adopted a flexible structure on the SWNT surface. In the presence of single-stranded DNA binding (SSB) proteins, the heights of the hybrids in air and liquid increased to 6.4 ± 3.1 nm and 10.0 ± 4.5 nm, respectively. The AFM images clearly showed binding of the SSB proteins to the ssDNA-SWNT hybrids. The morphology of the SSB-ssDNA-SWNT hybrids was non-uniform, particularly in aqueous solution. The variance of hybrid height was quantitatively estimated by cross-section analysis along the long-axis of each hybrid. The SSB-ssDNA-SWNT hybrids showed much larger variance than the ssDNA-SWNT hybrids.

Tooth-borne distraction of the lower anterior subapical segment for correction of class II malocclusion, subsequent to genioplasty.

PubMed

Matsushita, Kazuhiro; Inoue, Nobuo; Yamaguchi, Hiro-o; Ooi, Kazuhiro; Totsuka, Yasunori

2011-09-01

Alveolar distraction is mainly used to increase height and width of the alveolar crest. This technique, however, is not typically used for lengthening the perimeter of the dental arch or improving teeth axes. We applied alveolar distraction in a tooth-borne manner in the second stage of our original method and obtained favorable results. We therefore present an outline of this method. Genioplasty was first performed to create an infrastructure for sequential advancement of the subapical alveolar segment. After bone union, anterior subapical alveolar osteotomy was performed. The stump of the osteotomized dentate segment was moved forward without changing the incisal edge position, and a box-type bioabsorbable plate with four holes was fixed only onto the dentate segment using two screws. After a latency period, two distraction devices were placed bilaterally to the brackets and activated at 1.0 mm/day. After reaching the desired position, the distractor was immobilized, and then replaced by resin temporary teeth to retain the created space. After the consolidation period, orthodontic treatment was restarted and teeth moved into the newly created space. Bimaxillary surgery was performed after completing pre-surgical orthodontic treatment. Finally, both desirable occlusion and functional masticatory function were obtained. This tooth-borne distraction system is one applicable method for patients with skeletal class II and crowding of lower anterior teeth, achieving good results particularly in combination with our original method.

Tooth loss, pancreatic cancer, and Helicobacter pylori.

PubMed

Stolzenberg-Solomon, Rachael Z; Dodd, Kevin W; Blaser, Martin J; Virtamo, Jarmo; Taylor, Philip R; Albanes, Demetrius

2003-07-01

Poor dental health has been associated with increased risks of oral, esophageal, and gastric cancer and may also be associated with pancreatic cancer. In addition, Helicobacter pylori has been found in dental plaque and has been associated with periodontal disease and pancreatic cancer. The objective was to investigate prospectively the relation between dentition history and pancreatic cancer in the Alpha-Tocopherol, Beta-Carotene Cancer Prevention Study cohort in Finland and the association between dentition history and H. pylori seropositivity in a cross-sectional sample of subjects without cancer (n = 475) from the same cohort. Of the 29,104 male smokers aged 50-69 y in the cohort for whom there were complete data, 174 developed pancreatic cancer from 1985 to 1997. Cox proportional hazard models were used to estimate age-, smoking-, education-, urban living-, and height-adjusted hazard ratios and 95% CIs for pancreatic cancer, and logistic regression models were used to estimate age- and education-adjusted odds ratios for H. pylori carriage. Tooth loss was positively associated with pancreatic cancer (edentulous compared with missing 0-10 teeth: hazard ratio = 1.63; 95% CI: 1.09, 2.46; P for trend = 0.02) but was not significantly associated with H. pylori seropositivity (edentulous compared with missing 0-10 teeth: odds ratio = 1.30; 95% CI: 0.73, 2.32; P for trend = 0.37). Additional studies are needed to evaluate the association between tooth loss and pancreatic cancer, as well as cancers at other gastrointestinal sites, particularly with respect to possible biological mechanisms.

Opportunity Studies Bait in Shark's Cage

NASA Technical Reports Server (NTRS)

2004-01-01

In its 49th sol on Mars, NASA's Opportunity had nearly concluded its scientific examination of the extreme southwestern end of the outcrop in Meridiani Planum. In the 'Shark's Cage' area of the neighborhood called 'Shoemaker's Patio,' featured in this image from the front hazard avoidance camera, Opportunity deployed its arm to study the features called 'Shark's Tooth,' 'Shark Pellets,' and 'Lamination.' 'Shark's Tooth' is a piece of the unusual red rind that appears to fill cracks in the outcrop. This rind may be some kind of chemical alteration of the rocks. 'Shark Pellets' is an area of soil that was under investigation as part of the crater soil survey. 'Lamination' is a target with very thin layers that resemble uniform pages in a book, an indication of how the sediments were deposited. A final experiment in this area will be attempted on sol 51. Opportunity's front left wheel will 'scuff' the rock called 'Carousel.' 'Scuffing' involves scraping the rock with one wheel while holding all the others still. This experiment essentially turns the rover wheels into tools, to try and determine the hardness of the target rock.

Silicon Sheet Quality is Improved By Meniscus Control

NASA Technical Reports Server (NTRS)

Yates, D. A.; Hatch, A. E.; Goldsmith, J. M.

1983-01-01

Better quality silicon crystals for solar cells are possible with instrument that monitors position of meniscus as sheet of solid silicon is drawn from melt. Using information on meniscus height, instrument generates feedback signal to control melt temperature. Automatic control ensures more uniform silicon sheets.

Stopping dynamics of a steady uniform granular flow over a rough incline

NASA Astrophysics Data System (ADS)

Deboeuf, Stéphanie; Saingier, Guillaume; Thiruvalluvar, Nitharshini; Lagrée, Pierre-Yves; Popinet, Stéphane; Staron, Lydie

2017-06-01

Granular material flowing on complex topographies are ubiquitous in industrial and geophysical situations. Even model granular flows are difficult to understand and predict. Recently, the frictional rheology μ(I) -describing the ratio of the shear stress to the normal stress as a function of the inertial number I, that compares inertial and confinement effects- allows unifying different configurations of granular flows. However it does not succeed in describing some phenomenologies, such as creep flow, deposit height, … Is it attributable to the rheology, to non-local effects, ...? Here, we consider a thin layer of grains flowing steadily and uniformly on a rough incline, when the input mass flow rate is suddenly stopped. We focus on the arrest dynamics by using both experimental and numerical approaches. We measure the height and surface velocities of the granular layer during the long-time stopping dynamics and we compare our experimental results with computations of depthaveraged equations for a fluid of rheology μ(I).

Analysis of flow field characteristics in IC equipment chamber based on orthogonal design

NASA Astrophysics Data System (ADS)

Liu, W. F.; Yang, Y. Y.; Wang, C. N.

2017-01-01

This paper aims to study the influence of the configuration of processing chamber as a part of IC equipment on flow field characteristics. Four parameters, including chamber height, chamber diameter, inlet mass flow rate and outlet area, are arranged using orthogonally design method to study their influence on flow distribution in the processing chamber with the commercial software-Fluent. The velocity, pressure and temperature distribution above the holder were analysed respectively. The velocity difference value of the gas flow above the holder is defined as the evaluation criteria to evaluate the uniformity of the gas flow. The quantitative relationship between key parameters and the uniformity of gas flow was found through analysis of experimental results. According to our study, the chamber height is the most significant factor, and then follows the outlet area, chamber diameter and inlet mass flow rate. This research can provide insights into the study and design of configuration of etcher, plasma enhanced chemical vapor deposition (PECVD) equipment, and other systems with similar configuration and processing condition.

FEM analysis of different dental root canal-post systems in young permanent teeth.

PubMed

Vitale, M C; Chiesa, M; Coltellaro, F; Bignardi, C; Celozzi, M; Poggio, C

2008-09-01

Aim of this work was to carry out a comparative evaluation of the structural behaviour of different root canal posts (cylindrical, conical and triple conical) fitted in a second lower bicuspid and subjected to compression and bending test. This study has been carried out by numerical method of structural analysis of finite elements (FEM, Finite Element Method). Different tridimensional models were obtained by CAT images of an extracted tooth, endodontically treated, filled with guttapercha and triple conical glass post. Images have been elaborated by a software for images (Mimics and Ansys) and CAD (Rhinoceros 3 D). In the models a II Class restoration has been virtually created. In the numerical simulation dental tissues (enamel, dentine and root cement), guttapercha, root canal cement, different posts, different techniques of cementation and crown restoration (composites and adhesive systems) have been considered. Strain distributions in dental tissues, in root canal cement and in posts have been compared. The equivalent tensions and the single components (traction, compression and cut) have been analysed. In all examined posts, the most strained part is resulted the coronal one, even if the total tension, in the different tooth-post analyzed systems, resulted uniformly distributed. A similar behaviour was shown by the root canal cement. According to the analyzed conditions of bond and load, varying according to the geometry of the considered posts, our results confirm that there is no substantial difference of deformation in posts, root canal cement and treated tooth.

Reducing stem bending increases the height growth of tall pines.

PubMed

Meng, Shawn X; Lieffers, Victor J; Reid, Douglas E B; Rudnicki, Mark; Silins, Uldis; Jin, Ming

2006-01-01

The hypothesis was tested that upper limits to height growth in trees are the result of the increasing bending moment of trees as they grow in height. The increasing bending moment of tall trees demands increased radial growth at the expense of height growth to maintain mechanical stability. In this study, the bending moment of large lodgepole pine (Pinus contorta Dougl. Ex Loud. var. latifolia Engelm.) was reduced by tethering trees at 10 m height to counter the wind load. Average bending moment of tethered trees was reduced to 38% of control trees. Six years of tethering resulted in a 40% increase in height growth relative to the period before tethering. By contrast, control trees showed decreased height growth in the period after tethering treatment. Average radial growth along the bole, relative to height growth, was reduced in tethered trees. This strongly suggests that mechanical constraints play a crucial role in limiting the height growth of tall trees. Analysis of bending moment and basal area increment at both 10 m and 1.3 m showed that the amount of wood added to the stem was closely related to the bending moment produced at these heights, in both control and tethered trees. The tethering treatment also resulted in an increase in the proportion of latewood at the tethering height, relative to 1.3 m height. For untethered control trees, the ratio of bending stresses at 10 m versus 1.3 m height was close to 1 in both 1998 and 2003, suggesting a uniform stress distribution along the outer surface of the bole.

Characterization technique for inhomogeneous 4H-SiC Schottky contacts: A practical model for high temperature behavior

NASA Astrophysics Data System (ADS)

Brezeanu, G.; Pristavu, G.; Draghici, F.; Badila, M.; Pascu, R.

2017-08-01

In this paper, a characterization technique for 4H-SiC Schottky diodes with varying levels of metal-semiconductor contact inhomogeneity is proposed. A macro-model, suitable for high-temperature evaluation of SiC Schottky contacts, with discrete barrier height non-uniformity, is introduced in order to determine the temperature interval and bias domain where electrical behavior of the devices can be described by the thermionic emission theory (has a quasi-ideal performance). A minimal set of parameters, the effective barrier height and peff, the non-uniformity factor, is associated. Model-extracted parameters are discussed in comparison with literature-reported results based on existing inhomogeneity approaches, in terms of complexity and physical relevance. Special consideration was given to models based on a Gaussian distribution of barrier heights on the contact surface. The proposed methodology is validated by electrical characterization of nickel silicide Schottky contacts on silicon carbide (4H-SiC), where a discrete barrier distribution can be considered. The same method is applied to inhomogeneous Pt/4H-SiC contacts. The forward characteristics measured at different temperatures are accurately reproduced using this inhomogeneous barrier model. A quasi-ideal behavior is identified for intervals spanning 200 °C for all measured Schottky samples, with Ni and Pt contact metals. A predictable exponential current-voltage variation over at least 2 orders of magnitude is also proven, with a stable barrier height and effective area for temperatures up to 400 °C. This application-oriented characterization technique is confirmed by using model parameters to fit a SiC-Schottky high temperature sensor's response.

Design for high-power, single-lobe, grating-surface-emitting quantum cascade lasers enabled by plasmon-enhanced absorption of antisymmetric modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigler, C.; Kirch, J. D.; Mawst, L. J.

2014-03-31

Resonant coupling of the transverse-magnetic polarized (guided) optical mode of a quantum-cascade laser (QCL) to the antisymmetric surface-plasmon modes of 2nd-order distributed-feedback (DFB) metal/semiconductor gratings results in strong antisymmetric-mode absorption. In turn, lasing in the symmetric mode, that is, surface emission in a single-lobe far-field beam pattern, is strongly favored over controllable ranges in grating duty cycle and tooth height. By using core-region characteristics of a published 4.6 μm-emitting QCL, grating-coupled surface-emitting (SE) QCLs are analyzed and optimized for highly efficient single-lobe operation. For infinite-length devices, it is found that when the antisymmetric mode is resonantly absorbed, the symmetric mode hasmore » negligible absorption loss (∼0.1 cm{sup −1}) while still being efficiently outcoupled, through the substrate, by the DFB grating. For finite-length devices, 2nd-order distributed Bragg reflector (DBR) gratings are used on both sides of the DFB grating to prevent uncontrolled reflections from cleaved facets. Equations for the threshold-current density and the differential quantum efficiency of SE DFB/DBR QCLs are derived. For 7 mm-long, 8.0 μm-wide, 4.6 μm-emitting devices, with an Ag/InP grating of ∼39% duty cycle, and ∼0.22 μm tooth height, threshold currents as low as 0.45 A are projected. Based on experimentally obtained internal efficiency values from high-performance QCLs, slope efficiencies as high as 3.4 W/A are projected; thus, offering a solution for watt-range, single-lobe CW operation from SE, mid-infrared QCLs.« less

Intraoral versus extraoral measurement of the height of the interproximal contact area in maxillary anterior teeth.

PubMed

Sghaireen, Mohd G; Albhiran, Heyam Mobark; Alzoubi, Ibrahim A; Lynch, Edward; Al-Omiri, Mahmoud K

2015-01-01

This study aimed to clinically quantify the apicoincisal height of the upper interproximal areas directly in patients' mouths compared to measurements on stone models. One hundred and fifty participants (75 females and 75 males, age range 20-45 years) were recruited for this study. A digital caliper was used to measure the anterior maxillary interproximal contact areas directly in patients' mouths and on stone models. The digital caliper accuracy was up to 0.01. The Statistical Package for Social Sciences software (SPSS, version 19.0, Chicago, Ill., USA) was used for statistical analysis. Statistical significance was based on probability values <0.05. The intraoral measurement of proximal contacts as well as the measurement on stone models showed that the dimensions of interproximal contacts on both sides of each tooth were significantly different (p < 0.001) and that the dimension of the mesial contact point was larger than that of the distal contact point of each tooth. The largest contact point was the one between the central incisors (direct intraoral measurement = 2.9-6.49 mm; model measurement = 3.31-6.91 mm). On the other hand, the contact point between the canine and first premolar was the smallest on both sides of the arch (0.63-2.52 mm intraorally, 0.98-2.88 mm on models). The intraoral measurement of contact points was more accurate than model measurements, and the differences were statistically significant (p < 0.001). The clinical evaluation of contact point dimensions using a digital caliper was more precise than measuring contact points on stone models; hence, it is a viable, quick and adequate method to be used routinely. © 2015 S. Karger AG, Basel.

[Finite element analysis of different load mode on tooth movement for space closure in patient with bimaxillary protrusion].

PubMed

Zhang, X B; Yin, Y F; Yao, H M; Han, Y H; Wang, N; Ge, Z L

2016-07-01

To investigate the stress distribution on the maxillary anterior teeth retracted with sliding mechanics and micro-implant anchorage using different retraction hook heights and positions. DICOM image data including maxilla and upper teeth were obtained with cone-beam CT. The three-dimensional finite element model was constructed using Mimics software. Brackets and archwire model were constructed using Creo software. The models were instantiated using Pro/Engineer software. Abaqus software was used to simulate the sliding mechanics by loading 2 N force on 0, 2, 4, 6, 8, 10 mm retraction hooks and three different positions, repectively. Rotation of the occlusal plane, the initial displacement and stress distribution of teeth were analyzed. Lingual rotation of maxillary central incisor(0.021°), gingival movement of the maxillary first molar(0.005 mm), and clockwise rotation of the maxillary occlusal plane(0.012°) were observed when the force application point located at the archwire level (0 mm). In contrast, 0.235° labial rotation of the maxillary central incisor, 0.015 mm occlusal movement of the maxillary first molar, and 0.075° anti-clockwise rotation of the maxillary occlusal plane were observed when the force application point located at the higher level(10 mm retraction hook). The more the force application point was located posteriorly at the archwire level, the less lingual rotation of the maxillary central incisor and the more buccal displacement of maxillary first molar was observed. Maxillary anterior tooth rotation and retraction, vertical displacement of posterior segment, and rotation of the occlusal plane could be controlled by adjusting the height and position of the retraction hook in space closure using miniscrew and sliding mechanics.

Air-atomizing splash-cone fuel nozzle reduces pollutant emissions from turbojet engines

NASA Technical Reports Server (NTRS)

Ingebo, R. D.; Norgren, C. T.

1973-01-01

Advantages of fuel nozzle over conventional pressure-atomizing fuel nozzles: simplicity of construction, ability to distribute fuel-air mixture uniformly across full height of combustor without using auxiliary air supply, reliability when using contaminated fuels, and durability of nozzle at high operating temperatures.

A fixed full-matrix method for determining ice sheet height change from satellite altimeter: an ENVISAT case study in East Antarctica with backscatter analysis

NASA Astrophysics Data System (ADS)

Yang, Yuande; Hwang, Cheinway; E, Dongchen

2014-09-01

A new method, called the fixed full-matrix method (FFM), is used to compute height changes at crossovers of satellite altimeter ground tracks. Using the ENVISAT data in East Antarctica, FFM results in crossovers of altimeter heights that are 1.9 and 79 times more than those from the fixed half method (FHM) and the one-row method (ORM). The mean standard error of height changes is about 14 cm from ORM, which is reduced to 7 cm by FHM and to 3 cm by FFM. Unlike FHM, FFM leads to uniform errors in the first-half and second-half height-change time series. FFM has the advantage in improving the accuracy of the change of height and backscattered power over ORM and FHM. Assisted by the ICESat-derived height changes, we determine the optimal threshold correlation coefficient (TCC) for a best correction for the backscatter effect on ENVISAT height changes. The TCC value of 0.92 yields an optimal result for FFM. With this value, FFM yields ENVISAT-derived height change rates in East Antarctica mostly falling between and 3 cm/year, and matching the ICESat result to 0.94 cm/year. The ENVISAT result will provide a constraint on the current mass balance result along the Chinese expedition route CHINARE.

Optimization of Heat Exchangers with Dimpled Surfaces to Improve the Performance in Thermoelectric Generators Using a Kriging Model

NASA Astrophysics Data System (ADS)

Li, Shuai; Wang, Yiping; Wang, Tao; Yang, Xue; Deng, Yadong; Su, Chuqi

2017-05-01

Thermoelectric generators (TEGs) have become a topic of interest for vehicle exhaust energy recovery. Electrical power generation is deeply influenced by temperature differences, temperature uniformity and topological structures of TEGs. When the dimpled surfaces are adopted in heat exchangers, the heat transfer rates can be augmented with a minimal pressure drop. However, the temperature distribution shows a large gradient along the flow direction which has adverse effects on the power generation. In the current study, the heat exchanger performance was studied in a computational fluid dynamics (CFD) model. The dimple depth, dimple print diameter, and channel height were chosen as design variables. The objective function was defined as a combination of average temperature, temperature uniformity and pressure loss. The optimal Latin hypercube method was used to determine the experiment points as a method of design of the experiment in order to analyze the sensitivity of the design variables. A Kriging surrogate model was built and verified according to the database resulting from the CFD simulation. A multi-island genetic algorithm was used to optimize the structure in the heat exchanger based on the surrogate model. The results showed that the average temperature of the heat exchanger was most sensitive to the dimple depth. The pressure loss and temperature uniformity were most sensitive to the parameter of channel rear height, h 2. With an optimal design of channel structure, the temperature uniformity can be greatly improved compared with the initial exchanger, and the additional pressure loss also increased.

Interdisciplinary Full Mouth Rehabilitation of a Patient with Amelogenesis Imperfecta: A Case Report with 8 Years Follow-up

PubMed Central

Sreedevi, S; Sanjeev, R; Ephraim, Rena; Joseph, Mathai

2014-01-01

This case report deals with the interdisciplinary approach of a 28-year-old lady with Amelogenesis imperfecta of the hypoplastic kind. The patient came with a chief illness of worn out teeth, unsatisfactory esthetics and severe sensitivity of teeth. Her family history revealed a related situation in her father’s brother and her sister. On clinical assessment, the crowns of all teeth were worn out. The plan of the treatment was to protect as much tooth structure, restore the vertical dimension, and improve esthetics and masticatory function. The treatment procedures involved prosthodontic, endodontic, and periodontic interventions. After recording the vertical height, endodontic treatment and crown lengthening were performed with respect to the lower anteriors. The lost vertical height was regained in stages by insertion of full coverage crowns for all the teeth. The patient’s esthetic and functional needs were met with systematic and sequential interdisciplinary treatment approach. PMID:25628493

Orthodontists' and laypeople's perception of smile height aesthetics in relation to varying degrees of transverse cant of anterior teeth.

PubMed

Shiyan, Huang; Xu, Qian; Shuhao, Xu; Nanquan, Rao; Xiaobing, Li

2016-05-01

To determine the effect of varying the transverse cant of the anterior teeth on orthodontists' and laypeople's perceptions of smile aesthetics, and the influence that smile height has on this perception. A 20-year-old Chinese female with an aesthetic smile and normal occlusion was chosen and agreed to participate. Digital pictures of her posed smile were taken and manipulated to create three smile height variations: low, medium, or high. Each variation was further manipulated to create varying degrees of transverse anterior tooth cant. Fifty-six laypeople and 40 orthodontists participated as raters of the dental and facial impact of the altered smile images. The orthodontists more commonly and precisely identified the transverse cants of the anterior teeth and the detracting influence on smile aesthetics compared with laypersons. The orthodontists accepted a lesser range of anterior transverse cant. Increased smile heights enhanced the capability of all raters to detect a transverse cant and reduced the acceptable cant range. In addition, an increased smile height worsened the detracting effects of the transverse anterior cant in all raters' perceptions of smile aesthetics. An increased display of teeth and angulation of an anterior cant increased the ability of raters in both groups to detect differences. Transverse cants of anterior teeth can affect orthodontists' and laypeople's perceptions of smile aesthetics. Smile height and incisor display were significant factors that affected the orthodontist's and layperson's perceptions of smile aesthetics, and suggested that a description of the detracting effect of an anterior transverse cant should also consider smile height. A transverse occlusal cant is an important aesthetic factor used by clinicians during orthodontic diagnosis and review. It is important to appreciate that there is a difference in perception between orthodontic professionals and patients (laypeople). The extent of this perceptual difference and influencing factors could help the clinician set more appropriate treatment goals.

Accordant summit heights, summit levels and the origin of the ``upper denudation level'' in the Serra do Mar (SE-Brazil, São Paulo): A study of hillslope forms and processes

NASA Astrophysics Data System (ADS)

Römer, Wolfgang

2008-08-01

In southern São Paulo the Serra do Mar is characterized by three distinct terrain types: 1) highly dissected areas with closely spaced ridges and accordant summit heights; 2) multiconvex hills; and 3) terrains with highly elevated watershed areas, irregular summit heights, and locally subdued relief. The development of this landscape is considered to be the result of the Cenozoic block-faulting and of the influences that are exerted by the differing lithological and structural setting of block-faulted compartments on weathering and erosion processes. In areas characterized by pronounced accordant summits the close coincidence between hillslope angle and the angle of limiting stability against landsliding points to a close adjustment of hillslope gradients and the mechanical properties of the regolith. The relative height of the hillslopes is functionally related to the spacing of the valleys and the gradient of the hillslopes. In areas with a regular spacing of v-shaped valleys and uniform rocks, this leads to the intersection of valley-side slopes in summits and ridges at a certain elevation. This elevation is determined by the length and steepness of the valley-side slopes. Therefore, the heights of the summits are geometrically constrained and are likely to indicate the upper limit of summit heights or an "upper denudation level" that is adjusted by hillslope processes to the incising streams. Accordant summit heights of this type are poor indicators of formerly more extensive denudation surfaces as it is also likely that they are a result of the long-term adjustment of hillslopes to river incision. The steep mountain flanks of block-faulted compartments on the other hand, comprise regolith-covered hillslopes that are closely adjusted to the maximum stable gradient as well as rock-slopes that are controlled by the rock-mass strength. Their summits are usually not accommodated into uniform summit levels. Highly elevated watershed areas exhibiting a subdued relief are detached from the base level response. On granitoid rocks these areas are often characterized by the rocky hills and domal rock outcrops. However, differences in the elevation of interfluves and summits between rocks of differing resistance and in the elevation of lithologically distinct individual fault-blocks imply that long-term weathering and erosion has transformed and lowered these landscapes. Therefore, these areas cannot be interpreted as a remnant of a pre-uplift topography and it appears to be unlikely that the height of the summits correlates with formerly more widespread planation surfaces in the far hinterland. The studies indicate that concepts such as the parallel retreat of hillslopes cannot account for the observed differences in the landscape. It is suggested that the Serra do Mar is consumed from the Atlantic and the inland side by spatially non-uniform developmental states. These states are determined by local differences in the coupling and distance to the regional base level and sea-level or are due to lithological and structural controls between and within the block-faulted compartments.

Approximate analytical solution to diurnal atmospheric boundary-layer growth under well-watered conditions

USDA-ARS?s Scientific Manuscript database

The system of governing equations of a simplified slab model of the uniformly-mixed, purely convective, diurnal atmospheric boundary layer (ABL) is shown to allow immediate solutions for the potential temperature and specific humidity as functions of the ABL height and net radiation when expressed i...

46 CFR 169.755 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

46 CFR 169.755 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

46 CFR 169.755 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

46 CFR 169.755 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

46 CFR 169.755 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

EXPERIMENTS ON STABLY AND NEUTRALLY STRATIFIED FLOW OVER A MODEL THREE-DIMENSIONAL HILL

EPA Science Inventory

The flow structure over a bell shaped hill (reciprocal of a fourth order polynomial in cross section and height h) was studied in large and small stably stratified towing tanks (with uniform density gradients) and in an unstratified wind tunnel. Observations were made at Froude n...

Development and MASH full-scale crash testing of a high-mounting-height temporary single sign support with aluminum sign.

DOT National Transportation Integrated Search

2013-03-01

Work zone traffic control devices such as temporary single sign supports are a primary means to communicate : information to motorists in work zone areas. The Federal Highway Administration and the Manual on Uniform Traffic : Control Devices require ...

Demographic, socioeconomic, and behavioral factors affecting patterns of tooth decay in the permanent dentition: Principal components and factor analyses

PubMed Central

Shaffer, John R.; Polk, Deborah E.; Feingold, Eleanor; Wang, Xiaojing; Cuenco, Karen T.; Weeks, Daniel E.; DeSensi, Rebecca S.; Weyant, Robert J.; Crout, Richard; McNeil, Daniel W.; Marazita, Mary L.

2012-01-01

Objectives Dental caries of the permanent dentition is a multi-factorial disease resulting from the complex interplay of endogenous and environmental risk factors. The disease is not easily quantified due to the innumerable possible combinations of carious lesions across individual tooth surfaces of the permanent dentition. Global measures of decay, such as the DMFS index (which was developed for surveillance applications), may not be optimal for studying the epidemiology of dental caries because they ignore the distinct patterns of decay across the dentition. We hypothesize that specific risk factors may manifest their effects on specific tooth surfaces leading to patterns of decay that can be identified and studied. In this study we utilized two statistical methods of extracting patterns of decay from surface-level caries data in order to create novel phenotypes with which to study the risk factors affecting dental caries. Methods Intra-oral dental examinations were performed on 1,068 participants aged 18 to 75 years to assess dental caries. The 128 tooth surfaces of the permanent dentition were scored as carious or not and used as input for principal components analysis (PCA) and factor analysis (FA), two methods of identifying underlying patterns without a priori knowledge of the patterns. Demographic (age, sex, birth year, race/ethnicity, and educational attainment), anthropometric (height, body mass index, waist circumference), endogenous (saliva flow), and environmental (tooth brushing frequency, home water source, and home water fluoride) risk factors were tested for association with the caries patterns identified by PCA and FA, as well as DMFS, for comparison. The ten strongest patterns (i.e., those that explain the most variation in the data set) extracted by PCA and FA were considered. Results The three strongest patterns identified by PCA reflected (i) global extent of decay (i.e., comparable to DMFS index), (ii) pit and fissure surface caries, and (iii) smooth surface caries, respectively. The two strongest patterns identified by FA corresponded to (i) pit and fissure surface caries and (ii) maxillary incisor caries. Age and birth year were significantly associated with several patterns of decay, including global decay/DMFS index. Sex, race, educational attainment, and tooth brushing were each associated with specific patterns of decay, but not with global decay/DMFS index. Conclusions Taken together, these results support the notion that caries experience is separable into patterns attributable to distinct risk factors. This study demonstrates the utility of such novel caries patterns as new outcomes for exploring the complex, multifactorial nature of dental caries. PMID:23106439

Demographic, socioeconomic, and behavioral factors affecting patterns of tooth decay in the permanent dentition: principal components and factor analyses.

PubMed

Shaffer, John R; Polk, Deborah E; Feingold, Eleanor; Wang, Xiaojing; Cuenco, Karen T; Weeks, Daniel E; DeSensi, Rebecca S; Weyant, Robert J; Crout, Richard; McNeil, Daniel W; Marazita, Mary L

2013-08-01

Dental caries of the permanent dentition is a multifactorial disease resulting from the complex interplay of endogenous and environmental risk factors. The disease is not easily quantitated due to the innumerable possible combinations of carious lesions across individual tooth surfaces of the permanent dentition. Global measures of decay, such as the DMFS index (which was developed for surveillance applications), may not be optimal for studying the epidemiology of dental caries because they ignore the distinct patterns of decay across the dentition. We hypothesize that specific risk factors may manifest their effects on specific tooth surfaces leading to patterns of decay that can be identified and studied. In this study, we utilized two statistical methods of extracting patterns of decay from surface-level caries data to create novel phenotypes with which to study the risk factors affecting dental caries. Intra-oral dental examinations were performed on 1068 participants aged 18-75 years to assess dental caries. The 128 tooth surfaces of the permanent dentition were scored as carious or not and used as input for principal components analysis (PCA) and factor analysis (FA), two methods of identifying underlying patterns without a priori knowledge of the patterns. Demographic (age, sex, birth year, race/ethnicity, and educational attainment), anthropometric (height, body mass index, waist circumference), endogenous (saliva flow), and environmental (tooth brushing frequency, home water source, and home water fluoride) risk factors were tested for association with the caries patterns identified by PCA and FA, as well as DMFS, for comparison. The ten strongest patterns (i.e. those that explain the most variation in the data set) extracted by PCA and FA were considered. The three strongest patterns identified by PCA reflected (i) global extent of decay (i.e. comparable to DMFS index), (ii) pit and fissure surface caries and (iii) smooth surface caries, respectively. The two strongest patterns identified by FA corresponded to (i) pit and fissure surface caries and (ii) maxillary incisor caries. Age and birth year were significantly associated with several patterns of decay, including global decay/DMFS index. Sex, race, educational attainment, and tooth brushing were each associated with specific patterns of decay, but not with global decay/DMFS index. Taken together, these results support the notion that caries experience is separable into patterns attributable to distinct risk factors. This study demonstrates the utility of such novel caries patterns as new outcomes for exploring the complex, multifactorial nature of dental caries. © 2012 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effects of low-level laser therapy on orthodontic tooth movement and root resorption after artificial socket preservation.

PubMed

Seifi, Massoud; Atri, Faezeh; Yazdani, Mohammad Masoud

2014-01-01

Low- level laser therapy has been used to stimulate the orthodontic tooth movements (OTM) previously. Furthermore, in the orthodontic treatments accompanying tooth extractions, the adjacent teeth move towards the extraction sites and close the space in some cases. Then, the adjacent tooth movements must be prevented in the treatments requiring space. Laser stimulates and at some doses decelerates tooth movement; it also improves healing process and enhances osteogenesis. Hence, it can prevent movement by osteogenesis adjacent to the tooth. The present study investigated the effects of low-level laser therapy on the OTM and root resorption following artificial socket preservation. In this experimental animal trial, 16 male albino rabbits were selected with similar characteristics and randomly divided in two groups. Under general anesthesia, an artificial socket, 8 mm in height, was created in the mesial aspect of the first premolars of the rabbits and filled with demineralized freeze dried bone allograft (DFDBA). The first premolars were connected to the incisors using nickel titanium coil springs. In experimental group, gallium-aluminum-arsenide (GaAlAs) laser was irritated mesial to first premolar where artificial socket was created continuously (808 nm). The cycle was 10 days irritation, 14 days rest, 10 days irritation, 14 days rest (Biostimulation mode). Control group was not laser irradiated. All animals were sacrificed after 48 days and the distance between the distal aspect of the first premolars, and the mesial surface of the second premolars was measured with leaf gauge. The specimens underwent histological assessments. Integrity of root and its resorption was observed under microscope calibration. The size of resorption lacunae was calculated in mm(2). Normality of data was proved according to Kolmogorov-Smirnov analysis, and Student's t-test was done. P value less than 0.05 was considered as significant. The mean OTM were 5.68 ± 1.21 mm in the control group and 6.0 ± 0.99 mm in the laser irradiated teeth with no statistically significant differences(P > 0.75). The mean root resorption was 1.61 ± 0.43 mm(2) and 0.18 ± 0.07 mm(2) in the control and experimental groups respectively being significantly lower in the laser irradiated teeth (P < 0.0001). The findings of the present study show that GaAlAs irradiation together with the application of DFDBA led to limited amount of the stimulated OTM. The laser beam irradiation in combination with alloplastic materials used for socket preservation could reduce the degree of root resorption significantly.

[Influence of different designs of marginal preparation on stress distribution in the mandibular premolar restored with endocrown].

PubMed

Guo, Jing; Wang, Xiao-Yu; Li, Xue-Sheng; Sun, Hai-Yang; Liu, Lin; Li, Hong-Bo

2016-02-01

To evaluate the effect of different designs of marginal preparation on stress distribution in the mandibular premolar restored with endocrown using three-dimensional finite element method. Four models with different designs of marginal preparation, including the flat margin, 90° shoulder, 135° shoulder and chamfer shoulder, were established to imitate mandibular first premolar restored with endocrown. A load of 100 N was applied to the intersection of the long axis and the occlusal surface, either parallel or with an angle of 45° to the long axis of the tooth. The maximum values of Von Mises stress and the stress distribution around the cervical region of the abutment and the endocrown with different designs of marginal preparation were analyzed. The load parallel to the long axis of the tooth caused obvious stress concentration in the lingual portions of both the cervical region of the tooth tissue and the restoration. The stress distribution characteristics on the cervical region of the models with a flat margin and a 90° shoulder were more uniform than those in the models with a 135° shoulder and chamfer shoulder. Loading at 45° to the long axis caused stress concentration mainly on the buccal portion of the cervical region, and the model with a flat margin showed the most favorable stress distribution patterns with a greater maximum Von Mises stress under this circumstance than that with a parallel loading. Irrespective of the loading direction, the stress value was the lowest in the flat margin model, where the stress value in the cervical region of the endocrown was greater than that in the counterpart of the tooth tissue. The stress level on the enamel was higher than that on the dentin nearby in the flat margin model. From the stress distribution point of view, endocrowns with flat margin followed by a 90° shoulder are recommended.

The Uniform Pattern of Growth and Skeletal Maturation during the Human Adolescent Growth Spurt.

PubMed

Sanders, James O; Qiu, Xing; Lu, Xiang; Duren, Dana L; Liu, Raymond W; Dang, Debbie; Menendez, Mariano E; Hans, Sarah D; Weber, David R; Cooperman, Daniel R

2017-12-01

Humans are one of the few species undergoing an adolescent growth spurt. Because children enter the spurt at different ages making age a poor maturity measure, longitudinal studies are necessary to identify the growth patterns and identify commonalities in adolescent growth. The standard maturity determinant, peak height velocity (PHV) timing, is difficult to estimate in individuals due to diurnal, postural, and measurement variation. Using prospective longitudinal populations of healthy children from two North American populations, we compared the timing of the adolescent growth spurt's peak height velocity to normalized heights and hand skeletal maturity radiographs. We found that in healthy children, the adolescent growth spurt is standardized at 90% of final height with similar patterns for children of both sexes beginning at the initiation of the growth spurt. Once children enter the growth spurt, their growth pattern is consistent between children with peak growth at 90% of final height and skeletal maturity closely reflecting growth remaining. This ability to use 90% of final height as easily identified important maturity standard with its close relationship to skeletal maturity represents a significant advance allowing accurate prediction of future growth for individual children and accurate maturity comparisons for future studies of children's growth.

Reactor for making uniform capsules

NASA Technical Reports Server (NTRS)

Wang, Taylor G. (Inventor); Anikumar, Amrutur V. (Inventor); Lacik, Igor (Inventor)

1999-01-01

The present invention provides a novel reactor for making capsules with uniform membrane. The reactor includes a source for providing a continuous flow of a first liquid through the reactor; a source for delivering a steady stream of drops of a second liquid to the entrance of the reactor; a main tube portion having at least one loop, and an exit opening, where the exit opening is at a height substantially equal to the entrance. In addition, a method for using the novel reactor is provided. This method involves providing a continuous stream of a first liquid; introducing uniformly-sized drops of the second liquid into the stream of the first liquid; allowing the drops to react in the stream for a pre-determined period of time; and collecting the capsules.

On the vertical distribution of water vapor in the Martian tropics

NASA Technical Reports Server (NTRS)

Haberle, Robert M.

1988-01-01

Although measurements of the column abundance of atmospheric water vapor on Mars have been made, measurements of its vertical distribution have not. How water is distributed in the vertical is fundamental to atmosphere-surface exchange processes, and especially to transport within the atmosphere. Several lines of evidence suggest that in the lowest several scale heights of the atmosphere, water vapor is nearly uniformly distributed. However, most of these arguments are suggestive rather than conclusive since they only demonstrate that the altitude to saturation is very high if the observed amount of water vapor is distributed uniformly. A simple argument is presented, independent of the saturation constraint, which suggests that in tropical regions, water vapor on Mars should be very nearly uniformly mixed on an annual and zonally averaged basis.

Evidence for competition and cooperation among climbing plants.

PubMed

Biernaskie, Jay M

2011-07-07

A plant's best strategy for acquiring resources may often depend on the identity of neighbours. Here, I ask whether plants adjust their strategy to local relatedness: individuals may cooperate (reduce competitiveness) with kin but compete relatively intensely with non-kin. In a greenhouse experiment with Ipomoea hederacea, neighbouring siblings from the same inbred line were relatively uniform in height; groups of mixed lines, however, were increasingly variable as their mean height increased. The reproductive yield of mixed and sibling groups was similar overall, but when adjusted to a common mean height and height inequality, the yield of mixed groups was significantly less. Where this difference in yield was most pronounced (among groups that varied most in height), mixed groups tended to allocate more mass to roots than comparable sibling groups, and overall, mixed groups produced significantly fewer seeds per unit mass of roots. These results suggest that, from the group perspective, non-kin may have wasted resources in below-ground competition at the expense of reproduction; kin groups, on the other hand, displayed the relative efficiency that is expected of reduced competitiveness.

Accurate core position control in polymer optical waveguides using the Mosquito method for three-dimensional optical wiring

NASA Astrophysics Data System (ADS)

Date, Kumi; Ishigure, Takaaki

2017-02-01

Polymer optical waveguides with graded-index (GI) circular cores are fabricated using the Mosquito method, in which the positions of parallel cores are accurately controlled. Such an accurate arrangement is of great importance for a high optical coupling efficiency with other optical components such as fiber ribbons. In the Mosquito method that we developed, a core monomer with a viscous liquid state is dispensed into another liquid state monomer for cladding via a syringe needle. Hence, the core positions are likely to shift during or after the dispensing process due to several factors. We investigate the factors, specifically affecting the core height. When the core and cladding monomers are selected appropriately, the effect of the gravity could be negligible, so the core height is maintained uniform, resulting in accurate core heights. The height variance is controlled in +/-2 micrometers for the 12 cores. Meanwhile, larger shift in the core height is observed when the needle-tip position is apart from the substrate surface. One of the possible reasons of the needle-tip height dependence is the asymmetric volume contraction during the monomer curing. We find a linear relationship between the original needle-tip height and the core-height observed. This relationship is implemented in the needle-scan program to stabilize the core height in different layers. Finally, the core heights are accurately controlled even if the cores are aligned on various heights. These results indicate that the Mosquito method enables to fabricate waveguides in which the cores are 3-dimensionally aligned with a high position accuracy.

Modelling bucket excavation by finite element

NASA Astrophysics Data System (ADS)

Pecingina, O. M.

2015-11-01

Changes in geological components of the layers from lignite pits have an impact on the sustainability of the cup path elements and under the action of excavation force appear efforts leading to deformation of the entire assembly. Application of finite element method in the optimization of components leads to economic growth, to increase the reliability and durability of the studied machine parts thus the machine. It is obvious usefulness of knowledge the state of mechanical tensions that the designed piece or the assembly not to break under the action of tensions that must cope during operation. In the course of excavation work on all bucket cutting force components, the first coming into contact with the material being excavated cutting edge. Therefore in the study with finite element analysis is retained only cutting edge. To study the field of stress and strain on the cutting edge will be created geometric patterns for each type of cup this will be subject to static analysis. The geometric design retains the cutting edge shape and on this on the tooth cassette location will apply an areal force on the abutment tooth. The cutting edge real pattern is subjected to finite element study for the worst case of rock cutting by symmetrical and asymmetrical cups whose profile is different. The purpose of this paper is to determine the displacement and tensions field for both profiles considering the maximum force applied on the cutting edge and the depth of the cutting is equal with the width of the cutting edge of the tooth. It will consider the worst case when on the structure will act both the tangential force and radial force on the bucket profile. For determination of stress and strain field on the form design of cutting edge profile will apply maximum force assuming uniform distribution and on the edge surface force will apply a radial force. After geometric patterns discretization on the cutting knives and determining stress field, can be seen that at the rectangular profile appears the "clogging" phenomenon of the cutting edge and at the polygonal profile the point of application remains constant without going inside. From the finite element method done in this paper it can be concluded that the polygonal profiles made of dihedral angles are much more durable and asymmetric cups tend to have uniform tension along the entire perimeter.

Clinical performance of a lithia disilicate-based core ceramic for three-unit posterior FPDs.

PubMed

Esquivel-Upshaw, Josephine F; Anusavice, Kenneth J; Young, Henry; Jones, Jack; Gibbs, Charles

2004-01-01

The purpose of this research project was to determine the clinical success rate of a lithia disilicate-based core ceramic for use in posterior fixed partial dentures (FPD) as a function of bite force, cement type, connector height, and connector width. Thirty ceramic FPD core frameworks were prepared using a heat-pressing technique and a lithia disilicate-based core ceramic. The maximum clenching force was measured for each patient prior to tooth preparation. Connector height and width were measured for each FPD. Patients were recalled yearly after cementation for 2 years and evaluated using 11 clinical criteria. All FPDs were examined by two independent clinicians, and rankings from 1 to 4 were made for each criterion (4 = excellent; 1 = unacceptable). Two of the 30 ceramic FPDs fractured within the 2-year evaluation period, representing a 93% success rate. One fracture was associated with a low occlusal force and short connector height (2.9 mm). The other fracture was associated with the greatest occlusal force (1,031 N) and adequate connector height. All criteria were ranked good to excellent during the 2-year recall for all remaining FPDs. The performance of the experimental core ceramic in posterior FPDs was promising, with only a 7% fracture rate after 2 years. Because of the limited sample size, it is not possible to identify the maximum clenching force that is allowable to prevent fracture caused by interocclusal forces.

Automatic 3D Extraction of Buildings, Vegetation and Roads from LIDAR Data

NASA Astrophysics Data System (ADS)

Bellakaout, A.; Cherkaoui, M.; Ettarid, M.; Touzani, A.

2016-06-01

Aerial topographic surveys using Light Detection and Ranging (LiDAR) technology collect dense and accurate information from the surface or terrain; it is becoming one of the important tools in the geosciences for studying objects and earth surface. Classification of Lidar data for extracting ground, vegetation, and buildings is a very important step needed in numerous applications such as 3D city modelling, extraction of different derived data for geographical information systems (GIS), mapping, navigation, etc... Regardless of what the scan data will be used for, an automatic process is greatly required to handle the large amount of data collected because the manual process is time consuming and very expensive. This paper is presenting an approach for automatic classification of aerial Lidar data into five groups of items: buildings, trees, roads, linear object and soil using single return Lidar and processing the point cloud without generating DEM. Topological relationship and height variation analysis is adopted to segment, preliminary, the entire point cloud preliminarily into upper and lower contours, uniform and non-uniform surface, non-uniform surfaces, linear objects, and others. This primary classification is used on the one hand to know the upper and lower part of each building in an urban scene, needed to model buildings façades; and on the other hand to extract point cloud of uniform surfaces which contain roofs, roads and ground used in the second phase of classification. A second algorithm is developed to segment the uniform surface into buildings roofs, roads and ground, the second phase of classification based on the topological relationship and height variation analysis, The proposed approach has been tested using two areas : the first is a housing complex and the second is a primary school. The proposed approach led to successful classification results of buildings, vegetation and road classes.

17 Years of Cloud Heights from Terra, and Beyond

NASA Astrophysics Data System (ADS)

Davies, R.

2017-12-01

The effective cloud height, H, is the integral of observed cloud-top heights, weighted by their frequency of occurrence. Here we look at changes in the effective cloud height, H', as measured by the Multiangle Imaging Spectroradiometer (MISR) on the first Earth Observing System platform, Terra. Terra was launched in December 1999, and now has over 17 years of consistently measured climate records. Globally, HG' has an important influence on Earth's climate, whereas regionally, HR' is a useful measure of low frequency changes in circulation patterns. MISR has a sampling error in the annual mean HG' of ≈11 m, allowing fairly small interannual variations to be detected. This paper extends the previous 15-year summary that showed significant differences in the long term mean hemispheric cloud height changes. Also of interest are the correlations in tropical cloud height changes and related teleconnections. The largest ephemeral values in the annual HR' [over 1.5 km] are noted over the Central Pacific and the Maritime Continent. These changes are strongly anticorrelated with each other, being directly related to changes in ENSO. They are also correlated with the largest ephemeral changes in HG'. Around the equator, we find at least four distinct centres of similar fluctuations in cloud height. This paper examines the relative time dependence of these regional height changes, separately for La Niña and El Niño events, and stresses the value of extending the time series of uniformly measured cloud heights from space beyond EOS-Terra.

Controlled irrigation of a structured packing as a method for increasing the efficiency of liquid mixture separation in the distillation column

NASA Astrophysics Data System (ADS)

Pavlenko, A. N.; Zhukov, V. E.; Pecherkin, N. I.; Nazarov, A. D.; Li, X.; Li, H.; Gao, X.; Sui, H.

2017-09-01

The use of modern structured packing in the distillation columns allows much more even distribution of the liquid film over the packing surface, but it does not completely solve the problem of uniform distribution of flow parameters over the entire height of the packing. Negative stratification of vapor along the packing height caused by different densities of vapor mixture components and higher temperature in the lower part of the column leads to formation of large-scale maldistributions of temperature and mixture composition over the column cross-section even under the conditions of uniform irrigation of packing with liquid. In these experiments, the idea of compensatory action of liquid distributor on the large-scale maldistribution of mixture composition over the column cross-section was implemented. The experiments were carried out in the distillation column with the diameter of 0.9 m on 10 layers of the Mellapak 350Y packing with the total height of 2.1 m. The mixture of R-21 and R-114 was used as the working mixture. To irrigate the packing, the liquid distributorr with 126 independently controlled solenoid valves overlapping the holes with the diameter of 5 mm, specially designed by the authors, was used. Response of the column to the action of liquid distributor was observed in real time according to the indications of 3 groups of thermometers mounted in 3 different cross-sections of the column. The experiments showed that the minimal correction of the drip point pattern in the controlled liquid distributor can significantly affect the pattern of flow parameter distribution over the cross-section and height of the mass transfer surface and increase separation efficiency of the column within 20%.

Monolayer graphene/SiC Schottky barrier diodes with improved barrier height uniformity as a sensing platform for the detection of heavy metals

PubMed Central

Eriksson, Jens; Khranovskyy, Volodymyr; Iakimov, Tihomir; Lloyd Spetz, Anita; Yakimova, Rositsa

2016-01-01

A vertical diode structure comprising homogeneous monolayer epitaxial graphene on silicon carbide is fabricated by thermal decomposition of a Si-face 4H-SiC wafer in argon atmosphere. Current–voltage characteristics of the graphene/SiC Schottky junction were analyzed by applying the thermionic-emission theory. Extracted values of the Schottky barrier height and the ideality factor are found to be 0.4879 ± 0.013 eV and 1.01803 ± 0.0049, respectively. Deviations of these parameters from average values are smaller than those of previously observed literature data, thereby implying uniformity of the Schottky barrier height over the whole diode area, a stable rectifying behaviour and a good quality of ohmic palladium–graphene contacts. Keeping in mind the strong sensitivity of graphene to analytes we propose the possibility to use the graphene/SiC Schottky diode as a sensing platform for the recognition of toxic heavy metals. Using density functional theory (DFT) calculations we gain insight into the nature of the interaction of cadmium, mercury and lead with graphene as well as estimate the work function and the Schottky barrier height of the graphene/SiC structure before and after applying heavy metals to the sensing material. A shift of the I–V characteristics of the graphene/SiC-based sensor has been proposed as an indicator of presence of the heavy metals. Since the calculations suggested the strongest charge transfer between Pb and graphene, the proposed sensing platform was characterized by good selectivity towards lead atoms and slight interferences from cadmium and mercury. The dependence of the sensitivity parameters on the concentration of Cd, Hg and Pb is studied and discussed. PMID:28144530

Monolayer graphene/SiC Schottky barrier diodes with improved barrier height uniformity as a sensing platform for the detection of heavy metals.

PubMed

Shtepliuk, Ivan; Eriksson, Jens; Khranovskyy, Volodymyr; Iakimov, Tihomir; Lloyd Spetz, Anita; Yakimova, Rositsa

2016-01-01

A vertical diode structure comprising homogeneous monolayer epitaxial graphene on silicon carbide is fabricated by thermal decomposition of a Si-face 4H-SiC wafer in argon atmosphere. Current-voltage characteristics of the graphene/SiC Schottky junction were analyzed by applying the thermionic-emission theory. Extracted values of the Schottky barrier height and the ideality factor are found to be 0.4879 ± 0.013 eV and 1.01803 ± 0.0049, respectively. Deviations of these parameters from average values are smaller than those of previously observed literature data, thereby implying uniformity of the Schottky barrier height over the whole diode area, a stable rectifying behaviour and a good quality of ohmic palladium-graphene contacts. Keeping in mind the strong sensitivity of graphene to analytes we propose the possibility to use the graphene/SiC Schottky diode as a sensing platform for the recognition of toxic heavy metals. Using density functional theory (DFT) calculations we gain insight into the nature of the interaction of cadmium, mercury and lead with graphene as well as estimate the work function and the Schottky barrier height of the graphene/SiC structure before and after applying heavy metals to the sensing material. A shift of the I - V characteristics of the graphene/SiC-based sensor has been proposed as an indicator of presence of the heavy metals. Since the calculations suggested the strongest charge transfer between Pb and graphene, the proposed sensing platform was characterized by good selectivity towards lead atoms and slight interferences from cadmium and mercury. The dependence of the sensitivity parameters on the concentration of Cd, Hg and Pb is studied and discussed.

Micro-PIXE study of metal loss from dental amalgam

NASA Astrophysics Data System (ADS)

Meesat, Ridthee; Sudprasert, Wanwisa; Guibert, Edouard; Wang, Liping; Chappuis, Thibault; Whitlow, Harry J.

2017-08-01

Mercury amalgams have been a topic of controversy ever since their introduction over 150 years ago as a dental material. An interesting question is if metals are released from the amalgam into the enamel and dentine tissue. To elucidate this PIXE mapping was used to investigate metal redistribution in an extracted molar tooth with a ∼30 year old high-Cu content amalgam filling. The tooth was sectioned and polished, and elemental mapping carried out on the amalgam/enamel, bulk amalgam and the wear surface of the amalgam. As expected, the amalgam was multiphase amalgam comprising of Cu-rich and Ag-rich grains with non-uniform distribution of Hg. The amalgam/dentine interface was clearly defined with amalgam elements on one side and C and P from hydroxyapatite on the other side with evidence of only slight interface corrosion. The peaks for Cu Hg and Zn were isolated from interfering signals with concentrations in the enamel tissue, observed to be at, or below the method detection limit. The proximity in energy of the Sn L α and Ca K α , peaks and the background on the Hg M α gave signal overlap which increased the MDL for these elements. Remarkably, a course grain texture in the amalgam was observed just below the biting surface of the amalgam which might be associated with tribochemical processes from mastication. This coupled with the clear absence of the amalgam metals from tooth tissue, even in close proximity to the interface, suggests that for this sample, release of Hg occurred via erosion or dissolution in saliva.

X-linked hypophosphatemia: the mutant gene is expressed in teeth as well as in kidney.

PubMed Central

Shields, E D; Scriver, C R; Reade, T; Fujiwara, T M; Morgan, K; Ciampi, A; Schwartz, S

1990-01-01

Mutation at a locus (HPDR) on the X chromosome (McKusick 30780 [HPDR1]; 30781 [HPDR2]) causes impaired renal phosphate transport, hypophosphatemia, and an associated impairment in the process of mineralization in bone and teeth (X-linked hypophosphatemia [XLH]). We measured the dental pulp profile area (PRATIO [= pulp area/tooth area]) and serum phosphorus (Pi) values in uniformly treated XLH patients (six males, 81 teeth, 1,457 Pi values; 11 females, 129 teeth, 1,439 Pi values). Serum Pi values, reflecting the metabolic environment of tooth development, were obtained by repeated measurement between 1 mo and 26 years of age during treatment. PRATIO values calculated from standardized Rinn radiographs were used as outcome measurements of tooth development in XLH patients and in age-matched controls (12 males, 100 teeth; 27 females, 275 teeth). Age-dependent serum Pi values were not different in the treated XLH males and females. In teeth forming primary dentin there was no gene dosage effect on PRATIO values apparent in subjects below 15 years of age. However, in teeth forming secondary dentin a gene dosage was found in the subjects aged 15 to 25 years: XLH male teeth (n = 65) mean +/- SD = 0.163 +/- 0.046; XLH female teeth (n = 75) mean +/- SD = 0.137 +/- 0.039; control teeth (n = 209) mean +/- SD = 0.116 +/- 0.023; (higher PRATIO values mean less development or mineralization of secondary dentin); differences in these PRATIO values (males vs. female and XLH vs. control) were significant by mixed-model analysis of variance.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2155529

Optimizing Maxillary Aesthetics of a Severe Compromised Tooth through Orthodontic Movement and Dental Implants

PubMed Central

de Avila, Erica Dorigatti; Cirelli, Joni Augusto; Cardoso, Mauricio de Almeida; Capelozza-Filho, Leopoldino; Borelli Barros, Luiz Antonio

2014-01-01

Treatment of severe compromised tooth in the maxillary anterior area still poses great challenge to the clinicians. Several treatment modalities have been proposed to restore the function and aesthetics in teeth with advanced periodontal disease. The present study aims to report a case of traumatic injury of a left-maxillary central incisor with ridge preservation, orthodontic movement, and implant therapy. A 45-year-old woman underwent the proposed treatment for her left central incisor: basic periodontal therapy, xenogenous bone graft, and guided bone regeneration (GBR). Six months after the graft procedure, orthodontic movement by means of alignment and leveling was made and a coronal displacement of the gingival margin and vertical bone apposition could be observed after 13 months of active movement. Afterwards, a dental implant was placed followed by a connective tissue graft and immediate provisionalization of the crown. In conclusion, orthodontic movement was effective to improve the gingival tissue and alveolar bone prior to implant placement favoring the aesthetic results. Six years postoperatively, the results revealed height and width alveolar bone gain indicating that the treatment proposed was able to restore all the functional and aesthetic parameters. PMID:24523969

A model to non-uniform Ni Schottky contact on SiC annealed at elevated temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pristavu, G.; Brezeanu, G.; Badila, M.

2015-06-29

Ni Schottky contacts on SiC have a nonideal behavior, with strong temperature dependence of the electrical parameters, caused by a mixed barrier on the contact area and interface states. A simple analytical model that establishes a quantitative correlation between Schottky contact parameter variation with temperature and barrier height non-uniformity is proposed. A Schottky contact surface with double Schottky barrier is considered. The main model parameters are the lower barrier (Φ{sub Bn,l}) and a p factor which quantitatively evaluates the barrier non-uniformity on the Schottky contact area. The model is validated on Ni/4H-SiC Schottky contacts, post metallization sintered at high temperatures.more » The measured I{sub F}–V{sub F}–T characteristics, selected so as not to be affected by interface states, were used for model correlation. An inhomogeneous double Schottky barrier (with both nickel silicide and Ni droplets at the interface) is formed by a rapid thermal annealing (RTA) at 750 °C. High values of the p parameter are obtained from samples annealed at this temperature, using the proposed model. A significant improvement in the electrical properties occurs following RTA at 800 °C. The expansion of the Ni{sub 2}Si phase on the whole contact area is evinced by an X-Ray diffraction investigation. In this case, the p factor is much lower, attesting the uniformity of the contact. The model makes it possible to evaluate the real Schottky barrier, for a homogenous Schottky contact. Using data measured on samples annealed at 800 °C, a true barrier height of around 1.73 V has been obtained for Ni{sub 2}Si/4H-SiC Schottky contacts.« less

Effect of fiber post length and abutment height on fracture resistance of endodontically treated premolars prepared for zirconia crowns.

PubMed

Lin, Jie; Matinlinna, Jukka Pekka; Shinya, Akikazu; Botelho, Michael George; Zheng, Zhiqiang

2018-04-01

The purpose of this study was to compare the fracture resistance, mode of fracture, and stress distribution of endodontically treated teeth prepared with three different fiber post lengths and two different abutment heights, using both experimental and finite element (FE) approaches. Forty-eight human maxillary premolars with two roots were selected and endodontically treated. The teeth were randomly distributed into six equally sized groups (n = 8) with different combinations of post lengths (7.5, 11, and 15 mm) and abutment heights (3 and 5 mm). All the teeth restored with glass fiber post (Rely X Fiber Post, 3M ESPE, USA) and a full zirconia crown. All the specimens were thermocycled and then loaded to failure at an oblique angle of 135°. Statistical analysis was performed for the effects of post length and abutment height on failure loads using ANOVA and Tukey's honestly significant difference test. In addition, corresponding FE models of a premolar restored with a glass fiber post were developed to examine mechanical responses. The factor of post length (P < 0.01) had a significant effect on failure load. The abutment height (P > 0.05) did not have a significant effect on failure load. The highest mean fracture resistance was recorded for the 15 mm post length and 5 mm abutment height test group, which was significantly more resistant to fracture than the 7.5 mm post and 5 mm abutment height group (P < 0.05). The FE analysis showed the peak compression and tension stress values of 7.5 mm post length were higher than that of 11 and 15 mm post length. The stress value of remaining tooth decreased as the post length was increased. Within the limitations of this experimental and FE analysis study, increasing the post length inside the root of endodontically treated premolar teeth restored with glass-fiber posts increase the fracture resistance to non-axial forces. Failure mode is more favorable with reduced abutment heights.

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

Interim Site-index Curves for Longleaf Pine Plantations

Treesearch

William D. Boyer

1980-01-01

No single set of site-index curves can be uniformly applied to young longleaf pine plantations without a sacrifice in reliability. A recent study using plantation remeasurement data indicated that planting-site condition (old fields and mechanically prepared or unprepared cutover forest sites) has a major impact on early plantation height growth. Stand density (...

Heat Transfer Coefficient Distribution in the Furnace of a 300MWe CFB Boiler

NASA Astrophysics Data System (ADS)

Zhang, P.; Lu, J. F.; Yang, H. R.; Zhang, J. S.; Zhang, H.; Yue, G. X.

Properly understanding and calculating the distributions of heat flux and heat transfer coefficient (α) in the furnace is important in designing a circulating fluidized bed (CFB) boiler, especially with supercritical parameters. Experimental study on the heat transfer in a commercial 300MWe CFB boiler was conducted. The α from the bed to the water wall was measured by the finite element method (FEM), at five different heights. The influence of suspension density and bed temperature on α was analyzed. It was found that the pressure difference between the inlet and exit of the three cyclones, and the chamber pressure of the corresponding loop seal were not equal. The results indicated the suspension solid density was non-uniform in the cross section at a certain height. Consequently, the distributions of heat flux and α in the horizontal plane in the furnace was non-uniform. The furnace can divided into three sections according to the arrangement of the platen superheaters hanging in the upper CFB furnace. In each section, the heat flux near the center showed increasing trend.

Gear Durability Shown To Be Improved by Superfinishing

NASA Technical Reports Server (NTRS)

Krautz, Timothy L.

2000-01-01

Gears, bearings, and similar mechanical elements transmit loads through contacting surfaces. At the NASA Glenn Research Center at Lewis Field, we postulated that the fatigue lives of gears could be improved by providing smoother tooth surfaces. A superfinishing process was applied to a set of conventionally ground, aerospace-quality gears. This process produced a highly polished, mirrorlike surface as shown in the preceding photograph. The surface fatigue lives of both superfinished and conventionally ground gears were measured by experiments. The superfinished gears survived about four times longer than the conventionally ground gears. These superfinished gears were produced from conventionally ground, aerospace-quality gears whose geometry had been inspected. The gears were superfinished by placing them in a vibrating bath consisting of water, detergent, abrasive powder, and small pieces of zinc. Upon removal from the bath, the surfaces were highly polished, as depicted in the preceding photograph. The gears were again inspected, and dimensional measurements made before and after the superfinishing operation were compared. Superfinishing removed the peaks of the grinding marks and left a much smoother surface. Profile and spacing checks proved that the overall gear tooth shape was not affected in any harmful way. Superfinishing uniformly removed approximately 2.5 microns from each surface.

Expanding the molecular-ruler process through vapor deposition of hexadecanethiol

PubMed Central

Patron, Alexandra M; Hooker, Timothy S; Santavicca, Daniel F

2017-01-01

The development of methods to produce nanoscale features with tailored chemical functionalities is fundamental for applications such as nanoelectronics and sensor fabrication. The molecular-ruler process shows great utility for this purpose as it combines top-down lithography for the creation of complex architectures over large areas in conjunction with molecular self-assembly, which enables precise control over the physical and chemical properties of small local features. The molecular-ruler process, which most commonly uses mercaptoalkanoic acids and metal ions to generate metal-ligated multilayers, can be employed to produce registered nanogaps between metal features. Expansion of this methodology to include molecules with other chemical functionalities could greatly expand the overall versatility, and thus the utility, of this process. Herein, we explore the use of alkanethiol molecules as the terminating layer of metal-ligated multilayers. During this study, it was discovered that the solution deposition of alkanethiol molecules resulted in low overall surface coverage with features that varied in height. Because features with varied heights are not conducive to the production of uniform nanogaps via the molecular-ruler process, the vapor-phase deposition of alkanethiol molecules was explored. Unlike the solution-phase deposition, alkanethiol islands produced by vapor-phase deposition exhibited markedly higher surface coverages of uniform heights. To illustrate the applicability of this method, metal-ligated multilayers, both with and without an alkanethiol capping layer, were utilized to create nanogaps between Au features using the molecular-ruler process. PMID:29181290

Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming

NASA Astrophysics Data System (ADS)

Tavakoli, A.; Naeini, H. Moslemi; Roohi, Amir H.; Gollo, M. Hoseinpour; Shahabad, Sh. Imani

2018-01-01

In the 3D laser forming process, developing an appropriate laser scan pattern for producing specimens with high quality and uniformity is critical. This study presents certain principles for developing scan paths. Seven scan path parameters are considered, including: (1) combined linear or curved path; (2) type of combined linear path; (3) order of scan sequences; (4) the position of the start point in each scan; (5) continuous or discontinuous scan path; (6) direction of scan path; and (7) angular arrangement of combined linear scan paths. Regarding these path parameters, ten combined linear scan patterns are presented. Numerical simulations show continuous hexagonal, scan pattern, scanning from outer to inner path, is the optimized. In addition, it is observed the position of the start point and the angular arrangement of scan paths is the most effective path parameters. Also, further experimentations show four sequences due to creat symmetric condition enhance the height of the bowl-shaped products and uniformity. Finally, the optimized hexagonal pattern was compared with the similar circular one. In the hexagonal scan path, distortion value and standard deviation rather to edge height of formed specimen is very low, and the edge height despite of decreasing length of scan path increases significantly compared to the circular scan path. As a result, four-sequence hexagonal scan pattern is proposed as the optimized perimeter scan path to produce bowl-shaped product.

Magnetic noise as the cause of the spontaneous magnetization reversal of RE–TM–B permanent magnets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dmitriev, A. I., E-mail: aid@icp.ac.ru; Talantsev, A. D., E-mail: artgtx32@mail.ru; Kunitsyna, E. I.

2016-08-15

The relation between the macroscopic spontaneous magnetization reversal (magnetic viscosity) of (NdDySm)(FeCo)B alloys and the spectral characteristics of magnetic noise, which is caused by the random microscopic processes of thermally activated domain wall motion in a potential landscape with uniformly distributed potential barrier heights, is found.

Increased uniformity by planting clones will likely have a minimal effect on inventory costs

Treesearch

Curtis L. VanderSchaaf; Dean W. Coble; David B. South

2012-01-01

When conducting inventories, reducing variability among tree diameters, heights, and ultimately volumes or biomass, can reduce the number of points/plots needed to obtain a desired level of precision. We present a simple analysis examining the potential reduction in discounted inventory costs when stand variability is decreased (via improved genetics and intensive...

Precise Measurement of Velocity Dependent Friction in Rotational Motion

ERIC Educational Resources Information Center

Alam, Junaid; Hassan, Hafsa; Shamim, Sohaib; Mahmood, Waqas; Anwar, Muhammad Sabieh

2011-01-01

Frictional losses are experimentally determined for a uniform circular disc exhibiting rotational motion. The clockwise and anticlockwise rotations of the disc, that result when a hanger tied to a thread is released from a certain height, give rise to vertical oscillations of the hanger as the thread winds and unwinds over a pulley attached to the…

29 CFR 1917.120 - Fixed stairways.

Code of Federal Regulations, 2011 CFR

2011-07-01

... be positioned within the range of 30 degrees to 50 degrees to the horizontal with uniform riser.... Riser height shall be from 6 to 7.5 inches (15.24 to 19.05 cm), stair width a minimum of 22 inches (55... stairs having four or more risers shall have stair railings or handrails complying with § 1917.112(c)(1...

29 CFR 1917.120 - Fixed stairways.

Code of Federal Regulations, 2013 CFR

2013-07-01

... be positioned within the range of 30 degrees to 50 degrees to the horizontal with uniform riser.... Riser height shall be from 6 to 7.5 inches (15.24 to 19.05 cm), stair width a minimum of 22 inches (55... stairs having four or more risers shall have stair railings or handrails complying with § 1917.112(c)(1...

29 CFR 1917.120 - Fixed stairways.

Code of Federal Regulations, 2012 CFR

2012-07-01

... be positioned within the range of 30 degrees to 50 degrees to the horizontal with uniform riser.... Riser height shall be from 6 to 7.5 inches (15.24 to 19.05 cm), stair width a minimum of 22 inches (55... stairs having four or more risers shall have stair railings or handrails complying with § 1917.112(c)(1...

29 CFR 1917.120 - Fixed stairways.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be positioned within the range of 30 degrees to 50 degrees to the horizontal with uniform riser.... Riser height shall be from 6 to 7.5 inches (15.24 to 19.05 cm), stair width a minimum of 22 inches (55... stairs having four or more risers shall have stair railings or handrails complying with § 1917.112(c)(1...

Studying Maximum Plantar Stress per Insole Design Using Foot CT-Scan Images of Hyperelastic Soft Tissues

PubMed Central

Sarikhani, Ali; Motalebizadeh, Abbas; Kamali Doost Azad, Babak

2016-01-01

The insole shape and the resulting plantar stress distribution have a pivotal impact on overall health. In this paper, by Finite Element Method, maximum stress value and stress distribution of plantar were studied for different insoles designs, which are the flat surface and the custom-molded (conformal) surface. Moreover, insole thickness, heel's height, and different materials were used to minimize the maximum stress and achieve the most uniform stress distribution. The foot shape and its details used in this paper were imported from online CT-Scan images. Results show that the custom-molded insole reduced maximum stress 40% more than the flat surface insole. Upon increase of thickness in both insole types, stress distribution becomes more uniform and maximum stress value decreases up to 10%; however, increase of thickness becomes ineffective above a threshold of 1 cm. By increasing heel height (degree of insole), maximum stress moves from heel to toes and becomes more uniform. Therefore, this scenario is very helpful for control of stress in 0.2° to 0.4° degrees for custom-molded insole and over 1° for flat insole. By changing the material of the insole, the value of maximum stress remains nearly constant. The custom-molded (conformal) insole which has 0.5 to 1 cm thickness and 0.2° to 0.4° degrees is found to be the most compatible form for foot. PMID:27843284

Clinical evaluations of mineralized collagen in the extraction sites preservation

PubMed Central

Feng, Lu; Zhang, Liang; Cui, Yun; Song, Tian-Xi; Qiu, Zhi-Ye; Wang, Xiu-Mei; Tan, Bao-Sheng

2016-01-01

The purpose of this study was to explore the different effects between biomimetic mineralized collagen (MC) and ordinary physically blended hydroxyapatite/collagen (HA/Col) composite in evaluating new bone formation and regenerated bone height in human extraction sockets. Thirty-four patients who cannot retain teeth caused by trauma or decay were randomly selected from Department of Stomatology of Dongzhimen Hospital from December 2013 to December 2014. The patients were randomly divided into two groups. After the operation of tooth extraction, 17 patients were implanted with biomimetic MC (MC group), and other 17 patients were implanted with ordinary physically blended nHA/Col composite (nHA/Col group). X-ray positioning projection by auto-photographing was taken to test the distance between the lowest position and the neighboring CEJm-CEJd immediately, 1 month and 3 months after the operation. The height of new bone formation of the MC group was significantly higher than the nHA/Col group. Biomimetic MC showed better clinical outcomes in the bone formation for extraction site preservation and would have broad application prospect in the field of oral and maxillofacial surgeries. PMID:26815224

Image analysis of the eruptive positions of third molars and adjacent second molars as indicators of age evaluation in Thai patients.

PubMed

Mahasantipiya, Phattaranant May; Pramojanee, Sakarat; Thaiupathump, Trasapong

2013-12-01

This study was performed to determine the relationship between the stage of tooth eruption (both vertical and mesio-angular) and chronological age. Indirect digital panoramic radiographs were used to measure the distances from the dentinoenamel junction (DEJ) of the second molars to the occlusal plane of the second molar teeth and of the adjacent third molars in 264 Thai males and 437 Thai females using ImageJ software. The ratio of those distances was calculated by patient age, and the correlation coefficient of the ratio of the third molar length to the second molar length was calculated. The correlation between the height of the vertically erupted upper third molar teeth and age was at the intermediate level. The age range of ≥15 to <16 years was noted to be the range in which the correlation between the chronological age determined from the eruptional height and actual chronological age was statistically significant. The mean age of the female subjects, in which the position of the right upper third molar teeth was at or above the DEJ of the adjacent second molar but below one half of its coronal height was 19.9±2.6 years. That for the left side was 20.2±2.7 years. The mean ages of the male subjects were 20.1±3.3 years and 19.8±2.7 years for the right and left sides, respectively. It might be possible to predict chronological age from the eruption height of the wisdom teeth.

Evaluation of maxillary anterior teeth and their relation to the golden proportion in Malaysian population.

PubMed

Al-Marzok, Maan Ibrahim; Majeed, Kais Raad Abdul; Ibrahim, Ibrahim Khalil

2013-01-24

The maxillary anterior teeth are important in achieving pleasing dental aesthetics. Various methods are used to measure the size and form of them, including the golden proportion between their perceived widths, and the width-to-height ratio, referred to as the golden standard. The purpose of this study was conducted to evaluate whether consistent relationships exist between tooth width and height of the clinical crown dimensions; and to investigate the occurrence of the golden proportion of the maxillary anterior teeth. Dental casts of the maxillary arches were made in this cross-sectional study from MAHSA University College students who met the inclusion criteria. The 49 participants represented the Malaysian population main ethnics. The dimensions of the anterior teeth and the perceived width of anterior teeth viewed from front were measured using a digital caliper. Comparison of the perceived width ratio of lateral to central incisor and canine to lateral incisor with the golden proportion of 0.618 revealed there were a significant statistical difference (p < 0.05). The statistical difference was significant for the width-to-height ratio of central incisors to the golden standard of 80%. There was no significant difference in the comparison among ethnic groups for the golden proportion and the golden standard. The golden proportion was not found to exist between the perceived widths of maxillary anterior teeth. No golden standard were detected for the width-to-height proportions of maxillary incisors. Specific population characteristics and perception of beauty must be considered. However, ethnicity has no association with the proportions of maxillary anterior teeth.

Rugometric and microtopographic non-invasive inspection in dental-resin composites and zirconia ceramics

NASA Astrophysics Data System (ADS)

Fernández-Oliveras, Alicia; Costa, Manuel F. M.; Pecho, Oscar E.; Rubiño, Manuel; Pérez, María. M.

2013-11-01

Surface properties are essential for a complete characterization of biomaterials. In restorative dentistry, the study of the surface properties of materials meant to replace dental tissues in an irreversibly diseased tooth is important to avoid harmful changes in future treatments. We have experimentally analyzed the surface characterization parameters of two different types of dental-resin composites and pre-sintered and sintered zirconia ceramics. We studied two shades of both composite types and two sintered zirconia ceramics: colored and uncolored. Moreover, a surface treatment was applied to one specimen of each dental-resin. All the samples were submitted to rugometric and microtopographic non-invasive inspection with the MICROTOP.06.MFC laser microtopographer in order to gather meaningful statistical parameters such as the average roughness (Ra), the root-mean-square deviation (Rq), the skewness (Rsk), and the kurtosis of the surface height distribution (Rku). For a comparison of the different biomaterials, the uncertainties associated to the surface parameters were also determined. With respect to Ra and Rq, significant differences between the composite shades were found. Among the dental resins, the nanocomposite presented the highest values and, for the zirconia ceramics, the pre-sintered sample registered the lowest ones. The composite performance may have been due to cluster-formation variations. Except for the composites with the surface treatment, the sample surfaces had approximately a normal distribution of heights. The surface treatment applied to the composites increased the average roughness and moved the height distribution farther away from the normal distribution. The zirconia-sintering process resulted in higher average roughness without affecting the height distribution.

Shielding techniques tackle EMI excesses. V - EMI shielding

NASA Astrophysics Data System (ADS)

Grant, P.

1982-10-01

The utilization of shielding gaskets in EMI design is presented in terms of seam design, gasket design, groove design, and fastener spacing. The main function of seam design is to minimize the coupling efficiency of a seam, and for effective shielding, seam design should include mating surfaces which are as flat as possible, and a flange width at least five times the maximum anticipated separation between mating surfaces. Seam surface contact with a gasket should be firm, continuous, and uniform. Gasket height, closure pressure, and compression set as a function of the applied pressure parameters are determined using compression/deflection curves. Environmental seal requirements are given and the most common materials used are neoprene, silicone, butadiene-acrylonitrile, and natural rubber. Groove design is also discussed, considering gasket heights and cross-sectional areas. Finally, fastener spacing is considered, by examining deflection as a percentage of gasket height.

Sedimentation from particle-bearing plumes in a stratified ambient

NASA Astrophysics Data System (ADS)

Sutherland, Bruce R.; Hong, Youn Sub Dominic

2016-11-01

Laboratory experiments are performed to examine the sedimentation of particles that initially rise in a plume, then spread radially and settle in uniformly stratified fluid. Using light attenuation, the depth of the sediment bed is measured nonintrusively as a function of radius from the center of the plume. To gain some insight into these dynamics, an idealized model is developed by adapting well-established plume theory and a theory that accounts for sedimentation from surface gravity currents emanating from a plume impacting a rigid lid. We also account for recycling of falling particles that are re-entrained into the plume. With a suitable choice of parameters determining the intrusion height, entrainment during fountain collapse, and the radius at which settling from the intrusion begins, in most cases for which particles are predicted to be drawn back into the plume and recycled. The predictions for intrusion height, particle mound height, and spread agree within 20% of observations.

Experimental test of theory for the stability of partially saturated vertical cut slopes

USGS Publications Warehouse

Morse, Michael M.; Lu, N.; Wayllace, Alexandra; Godt, Jonathan W.; Take, W.A.

2014-01-01

This paper extends Culmann's vertical-cut analysis to unsaturated soils. To test the extended theory, unsaturated sand was compacted to a uniform porosity and moisture content in a laboratory apparatus. A sliding door that extended the height of the free face of the slope was lowered until the vertical cut failed. Digital images of the slope cross section and upper surface were acquired concurrently. A recently developed particle image velocimetry (PIV) tool was used to quantify soil displacement. The PIV analysis showed strain localization at varying distances from the sliding door prior to failure. The areas of localized strain were coincident with the location of the slope crest after failure. Shear-strength and soil-water-characteristic parameters of the sand were independently tested for use in extended analyses of the vertical-cut stability and of the failure plane angle. Experimental failure heights were within 22.3% of the heights predicted using the extended theory.

Influence of material surface on the scanning error of a powder-free 3D measuring system.

PubMed

Kurz, Michael; Attin, Thomas; Mehl, Albert

2015-11-01

This study aims to evaluate the accuracy of a powder-free three-dimensional (3D) measuring system (CEREC Omnicam, Sirona), when scanning the surface of a material at different angles. Additionally, the influence of water was investigated. Nine different materials were combined with human tooth surface (enamel) to create n = 27 specimens. These materials were: Controls (InCoris TZI and Cerec Guide Bloc), ceramics (Vitablocs® Mark II and IPS Empress CAD), metals (gold and amalgam) and composites (Tetric Ceram, Filtek Supreme A2B and A2E). The highly polished samples were scanned at different angles with and without water. The 216 scans were then analyzed and descriptive statistics were obtained. The height difference between the tooth and material surfaces, as measured with the 3D scans, ranged from 0.83 μm (±2.58 μm) to -14.79 μm (±3.45 μm), while the scan noise on the materials was between 3.23 μm (±0.79 μm) and 14.24 μm (±6.79 μm) without considering the control groups. Depending on the thickness of the water film, measurement errors in the order of 300-1,600 μm could be observed. The inaccuracies between the tooth and material surfaces, as well as the scan noise for the materials, were within the range of error for measurements used for conventional impressions and are therefore negligible. The presence of water, however, greatly affects the scan. The tested powder-free 3D measuring system can safely be used to scan different material surfaces without the prior application of a powder, although drying of the surface prior to scanning is highly advisable.

Torque resistance of different stainless steel wires commonly used for fixed retainers in orthodontics.

PubMed

Arnold, Dario T; Dalstra, Michel; Verna, Carlalberta

2016-06-01

Movements of teeth splinted by fixed retention wires after orthodontic treatment have been observed. The aetiological factors for these movements are unknown. The aim of this in vitro study was to compare the resistance to torque of different stainless steel wires commonly used for fixed retainers in orthodontics. Torquing moments acting on a retainer wire were measured in a mechanical force testing system by applying buccal crown torque to an upper lateral incisor in both a 3-teeth and in a 2-teeth setup. Seven stainless steel wires with different shape, type (plain, braided, coaxial, or chain) and dimensions were selected for this study. For a torquing angle of 16.2° in the 3-teeth setup torsion moments can vary between 390 cNmm and 3299 cNmm depending on the retainer wire. For the 2-teeth setup the torsion moments are much smaller. Exposure to the flame of a butane-gas torch for 10 seconds to anneal the wire reduces the stiffness of the retainer wire. Clinicians must select wires for fixed retainers very carefully since the difference in resistance to torque is large. A high level of torque control can be achieved with a plain 0.016 × 0.016-inch or a braided 0.016 × 0.022-inch stainless steel wire. A tooth attached by a retainer wire to only one neighbouring tooth is less resistant to torque than a tooth connected to two neighbouring teeth. Annealing a retainer wire with a flame reduces the stiffness of the wire markedly and can lead to a non-uniform and non-reproducible effect.

"Closed Reduction" Principles Can Manage Diverse Conditions of Temporomandibular Joint Vertical Height Loss: From Displaced Condylar Fractures to Idiopathic Condylar Resorption.

PubMed

Nitzan, Dorrit W; Palla, Sandro

2017-06-01

The aim of this case series was to describe a modification of the classic "closed reduction" technique to manage unilateral or anterior open bite owing to a loss in vertical height (LVH) caused by several disorders and pathologies other than displaced condylar fractures. The protocol included insertion of an occlusal appliance to increase the height of the premature contact and the width of the open bite, stabilization of the dental arches by rigid arches, and the use, during sleep, of rubber bands in the open bite region to pull the mandible cranially. In addition, when awake, the patient performed physiotherapy exercises to guide the mandible into maximum intercuspation. The increased open bite enhanced the effect of the rubber bands in guiding the mandible into the original habitual occlusion and the rigid arches served to minimize tooth eruption. The present cases showed the favorable outcome of this low-risk treatment in the re-establishment of the original habitual occlusion within 1 to 4 weeks and without reconstruction of the LVH. The efficacy of this complication-free approach to correct occlusion in various conditions of LVH suggests that this protocol should be applied before venturing into surgical intervention. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Characteristics of surface roughness associated with leading edge ice accretion

NASA Technical Reports Server (NTRS)

Shin, Jaiwon

1994-01-01

Detailed size measurements of surface roughness associated with leading edge ice accretions are presented to provide information on characteristics of roughness and trends of roughness development with various icing parameters. Data was obtained from icing tests conducted in the Icing Research Tunnel (IRT) at NASA Lewis Research Center (LeRC) using a NACA 0012 airfoil. Measurements include diameters, heights, and spacing of roughness elements along with chordwise icing limits. Results confirm the existence of smooth and rough ice zones and that the boundary between the two zones (surface roughness transition region) moves upstream towards stagnation region with time. The height of roughness grows as the air temperature and the liquid water content increase, however, the airspeed has little effect on the roughness height. Results also show that the roughness in the surface roughness transition region grows during a very early stage of accretion but reaches a critical height and then remains fairly constant. Results also indicate that a uniformly distributed roughness model is only valid at a very initial stage of the ice accretion process.

Origins of the Solar Wind

NASA Technical Reports Server (NTRS)

Warren, Harry; Gurman, Joseph (Technical Monitor)

2002-01-01

This paper presented the differential emission measure analysis of SUMER observations of a coroner streamer. We found that: The coroner streamer is isothermal at all heights. This suggests that the loops comprising the streamer must have very flat temperature profiles. The coroner streamer is "overdense" relative to the predictions of hydrostatic equilibrium at most heights. At the lowest heights the streamer is actually "underdense". The SUMER temperature measurements are not consistent with those derived from simultaneous SXT observations. SXT indicates systematically higher temperatures as well as a strong temperature gradient. These SUMER measurements yield somewhat lower temperatures and no gradient in the temperature with height. Previous work has suggested that there may be a hot component to the streamer that is preferentially observed with SXT. Our analysis shows that high temperature emission lines would be observed with SUMER if this were true and thus discounts this possibility. We suggested that scattered light in SXT might produce spurious temperature measurements. The temperature and density structure of this coroner streamer are very similar to "TRACE" active region loops (flat temperature profiles, overdense relative to uniform heating, and relatively cool temperatures).

Impact of digital prosthodontic planning on dental esthetics: Biometric analysis of esthetic parameters.

PubMed

Abduo, Jaafar; Bennamoun, Mohammed; Tennant, Marc; McGeachie, John

2016-01-01

Improving dental esthetics is a main objective of prosthodontic treatment. Recently, digital diagnostic waxing has been proposed as an alternative to conventional diagnostic waxing; however, the impact on esthetics has not been evaluated. The purpose of this study was to evaluate the impact of diagnostic waxing on biometric esthetic variables and to compare the esthetic outcome achieved by digital waxing with conventional waxing. Three biometric variables were evaluated: perceived frontal proportion (PFP), width/height (W:H) ratio, and symmetry. Maxillary casts of 13 patients were collected. All of them had maxillary anterior teeth that required prosthodontic treatment. Two forms of diagnostic waxing were executed: conventional and digital waxing. Measurements of the esthetic variables were conducted digitally. For the PFP, a frontal image was made and the width of each tooth was measured. Subsequently, the PFP values of the lateral incisor to central incisor and of the canine to central incisor were calculated. In addition, the height and width of each tooth was measured to calculate the W:H ratio. Using the previous measurements, the symmetry between the right and left sides was determined. No consistent or recurrent PFP was detected for any cast. The diagnostic waxing did not alter the PFP of the pretreatment casts. The diagnostic waxing had restored the W:H ratio to what is assumed to be a natural ratio. An improvement in symmetry was detected after the diagnostic waxing and was more prominent after the digital waxing. However, no significant difference was found between the 2 diagnostic waxing methods. The 2 diagnostic waxing methods influenced the esthetic variables of the anterior maxillary teeth and yielded similar outcomes. Digital waxing appears to be a reasonable alternative, but further investigations are needed to ensure its practicality. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Characterization of periodontal structures of enamelin-null mice.

PubMed

Chan, Hsun-Liang; Giannobile, William V; Eber, Robert M; Simmer, James P; Hu, Jan C

2014-01-01

Enamelin-null (ENAM(-/-)) mice have no enamel. When characterizing ENAM(-/-) mice, alveolar bone height reduction was observed, and it was hypothesized that enamel defects combined with diet are associated with the periodontal changes of ENAM(-/-)mice. The aim of the present study is to compare the dimension of interradicular bone of ENAM(-/-) (knock-out [KO]) with wild-type (WT) mice, maintained on hard (HC) or soft (SC) chow. A total of 100 animals divided into four groups were studied at 3, 8, and 24 weeks of age: 1) KO/HC; 2) KO/SC; 3) WT/HC; and 4) WT/SC. Microcomputed tomography was performed, and the following measurements were made between mandibular first (M1) and second (M2) molars: relative alveolar bone height (RBH), crestal bone width (CBW), bone volume (BV), bone mineral content (BMC), and bone mineral density (BMD). The position of M1 and M2 in relation to the inferior border of the mandible was also determined at 24 weeks. All variables were analyzed by one-way analysis of variance and Dunnett test for pairwise comparisons. Morphologic analyses were conducted on hematoxylin and eosin-stained sections. Radiographically, the enamel layer was absent in ENAM(-/-) mice. Interproximal open contacts were observed exclusively in ENAM(-/-) mice, and the prevalence decreased over time, suggesting that a shifting of tooth position had occurred. Additionally, in the two ENAM(-/-) groups, RBH was significantly lower at 8 and 24 weeks (P <0.02); CBW, BV, and BMC were significantly less (P <0.05) at 24 weeks. No differences in BMD were found among the four groups. The molars migrated to a more coronal position in ENAM(-/-) mice and mice on HC. Histologic findings were consistent with radiographic observations. After eruption, the junctional epithelium was less organized in ENAM(-/-) mice. The interdental bone density was not affected in the absence of enamelin, but its volume was, which is likely a consequence of alternations in tooth position.

Pore-scale modeling of Capillary Penetration of Wetting Liquid into 3D Fibrous Media: A Critical Examination of Equivalent Capillary Concept

NASA Astrophysics Data System (ADS)

Palakurthi, Nikhil Kumar; Ghia, Urmila; Comer, Ken

2013-11-01

Capillary penetration of liquid through fibrous porous media is important in many applications such as printing, drug delivery patches, sanitary wipes, and performance fabrics. Historically, capillary transport (with a distinct liquid propagating front) in porous media is modeled using capillary-bundle theory. However, it is not clear if the capillary model (Washburn equation) describes the fluid transport in porous media accurately, as it assumes uniformity of pore sizes in the porous medium. The present work investigates the limitations of the applicability of the capillary model by studying liquid penetration through virtual fibrous media with uniform and non-uniform pore-sizes. For the non-uniform-pore fibrous medium, the effective capillary radius of the fibrous medium was estimated from the pore-size distribution curve. Liquid penetration into the 3D virtual fibrous medium at micro-scale was simulated using OpenFOAM, and the numerical results were compared with the Washburn-equation capillary-model predictions. Preliminary results show that the Washburn equation over-predicts the height rise in the early stages (purely inertial and visco-inertial stages) of capillary transport.

Free-surface flow of liquid oxygen under non-uniform magnetic field

NASA Astrophysics Data System (ADS)

Bao, Shi-Ran; Zhang, Rui-Ping; Wang, Kai; Zhi, Xiao-Qin; Qiu, Li-Min

2017-01-01

The paramagnetic property of oxygen makes it possible to control the two-phase flow at cryogenic temperatures by non-uniform magnetic fields. The free-surface flow of vapor-liquid oxygen in a rectangular channel was numerically studied using the two-dimensional phase field method. The effects of magnetic flux density and inlet velocity on the interface deformation, flow pattern and pressure drop were systematically revealed. The liquid level near the high-magnetic channel center was lifted upward by the inhomogeneous magnetic field. The interface height difference increased almost linearly with the magnetic force. For all inlet velocities, pressure drop under 0.25 T was reduced by 7-9% due to the expanded local cross-sectional area, compared to that without magnetic field. This work demonstrates the effectiveness of employing non-uniform magnetic field to control the free-surface flow of liquid oxygen. This non-contact method may be used for promoting the interface renewal, reducing the flow resistance, and improving the flow uniformity in the cryogenic distillation column, which may provide a potential for enhancing the operating efficiency of cryogenic air separation.

47 CFR 90.309 - Tables and figures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 122 meters (400 foot) contour intervals may be used. Where the terrain is uniform or gently sloping... meters (feet) (AAT) 15 (50) 30.5 (100) 45 (150) 61 (200) 76 (250) 91.5 (300) 106 (350) 122 (400) 137 (450... height in meters (feet) (AAT) 15 (50) 30.5 (100) 45 (150) 61 (200) 76 (250) 91.5 (300) 106 (350) 122 (400...

HOW to Manage Jack Pine to Reduce Damage from Jack Pine Budworm

Treesearch

Deborah G. McCullough; Steven Katovich; Robert L. Heyd; Shane Weber

1994-01-01

Jack pine budworm, Choristoneura pinus pinus Freeman, is a needle feeding caterpillar that is generally considered the most significant pest of jack pine. Vigorous young jack pine stands are rarely damaged during outbreaks. The most vigorous stands are well stocked, evenly spaced, fairly uniform in height, and less than 45 years old. Stands older than 45 years that are...

Potential effect of stand structure on belowground allocation

Treesearch

Thomas J. Dean

2001-01-01

Stand structure affects two key variables that affect biomass allocation to the stem: leaf area and height to the center of the crown. By translating wind forces into bending moment, these variables generate bending stress within a stem. The uniform stress axiom of stem formation can be used to calculate current stem mass for a given bending moment and stem allocation...

A Laboratory Study of Vortical Structures in Rotating Convection Plumes

NASA Astrophysics Data System (ADS)

Fu, Hao; Sun, Shiwei; Wang, Yuan; Zhou, Bowen; Thermal Turbulence Research Team

2015-11-01

A laboratory study of the columnar vortex structure in rotating Rayleigh-Bénard convection is conducted. A rectangular water tank is uniformly heated from below and cooled from above, with Ra = (6 . 35 +/- 0 . 77) ×107 , Ta = 9 . 84 ×107 , Pr = 7 . 34 . The columnar vortices are vertically aligned and quasi steady. Two 2D PIV systems were used to measure velocity field. One system performs horizontal scans at 9 different heights every 13.6s, covering 62% of the total depth. The other system scans vertically to obtain the vertical velocity profile. The measured vertical vorticity profiles of most vortices are quasi-linear with height while the vertical velocities are nearly uniform with only a small curvature. A simple model to deduce vertical velocity profile from vertical vorticity profile is proposed. Under quasi-steady and axisymmetric conditions, a ``vortex core'' assumption is introduced to simplify vertical vorticity equation. A linear ODE about vertical velocity is obtained whenever a vertical vorticity profile is given and solved with experimental data as input. The result is approximately in agreement with the measurement. This work was supported by Undergraduates Training Project (J1103410).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trianti, Nuri, E-mail: nuri.trianti@gmail.com; Nurjanah,; Su’ud, Zaki

Thermalhydraulic of reactor core is the thermal study on fluids within the core reactor, i.e. analysis of the thermal energy transfer process produced by fission reaction from fuel to the reactor coolant. This study include of coolant temperature and reactor power density distribution. The purposes of this analysis in the design of nuclear power plant are to calculate the coolant temperature distribution and the chimney height so natural circulation could be occurred. This study was used boiling water reactor (BWR) with cylinder type reactor core. Several reactor core properties such as linear power density, mass flow rate, coolant density andmore » inlet temperature has been took into account to obtain distribution of coolant density, flow rate and pressure drop. The results of calculation are as follows. Thermal hydraulic calculations provide the uniform pressure drop of 1.1 bar for each channels. The optimum mass flow rate to obtain the uniform pressure drop is 217g/s. Furthermore, from the calculation it could be known that outlet temperature is 288°C which is the saturated fluid’s temperature within the system. The optimum chimney height for natural circulation within the system is 14.88 m.« less

Scalar Fluxes Near a Tall Building in an Aligned Array of Rectangular Buildings

NASA Astrophysics Data System (ADS)

Fuka, Vladimír; Xie, Zheng-Tong; Castro, Ian P.; Hayden, Paul; Carpentieri, Matteo; Robins, Alan G.

2018-04-01

Scalar dispersion from ground-level sources in arrays of buildings is investigated using wind-tunnel measurements and large-eddy simulation (LES). An array of uniform-height buildings of equal dimensions and an array with an additional single tall building (wind tunnel) or a periodically repeated tall building (LES) are considered. The buildings in the array are aligned and form long streets. The sensitivity of the dispersion pattern to small changes in wind direction is demonstrated. Vertical scalar fluxes are decomposed into the advective and turbulent parts and the influences of wind direction and of the presence of the tall building on the scalar flux components are evaluated. In the uniform-height array turbulent scalar fluxes are dominant, whereas the tall building produces an increase of the magnitude of advective scalar fluxes that yields the largest component. The presence of the tall building causes either an increase or a decrease to the total vertical scalar flux depending on the position of the source with respect to the tall building. The results of the simulations can be used to develop parametrizations for street-canyon dispersion models and enhance their capabilities in areas with tall buildings.

The implications of basalt in the formation and evolution of mountains on Venus

NASA Astrophysics Data System (ADS)

Jull, Matthew G.; Arkani-Hamed, Jafar

1995-06-01

The highland region of Ishtar Terra on Venus has mountains that reach up to 11 km in height and are thought to be basaltic in composition. Assuming that dynamic uplift of crust to this height is unlikely, we examine the topography produced by an isostatically supported thickening basaltic crust. It is found that regardless of whether the crust thickens by crustal shortening or by volcanic construction, the high-density basalt-eclogite phase transition is the limiting factor for producing significant elevation of the mountains. The maximum height attained by basaltic mountains depends on the nature of the basalt-eclogite phase transition. Without a phase transition, a basaltic crust must thicken to greater than 100 km to reach heights over 10 km. An instantaneous phase transition of basalt to eclogite allows a maximum topographic height of less than about 2 km. However, with a time lag of 100 Ma owing to slow rates of solid-state diffusion, our calculations show that the mountains can reach elevations greater than 10 km only if they are less than 25 Ma old. Higher temperatures within the Venusian crust may decrease the extent of the stability fields of high-density basalt phases and allow high topography if the thickening crust melts. This can occur if the radioactive element concentrations measured on the surface of Venus are uniformly distributed throughout the crust, the crust thickens to greater than 65 km, and the thickened crust is older than about 400 Ma. The conflicting results of a young age predicted for high basaltic mountains and an almost uniform surface age of 500 Ma from crater populations, coupled with similarities in bulk physical properties of Venus and Earth, suggest that the basaltic surface composition found at several landing sites on the planet may not be representative of the entire crust. We suggest that Ishtar Terra formed from the collision of continent-like highly silicic cratons over a region of mantle downwelling. Lakshmi Planum resulted from the thickening of a basaltic crust and the peripheral mountain belts formed from the collision of granitic cratons that were pulled toward a downwelling region of mantle.

D2+ Molecular complex in non-uniform height quantum ribbon under crossed electric and magnetic fields

NASA Astrophysics Data System (ADS)

Suaza, Y. A.; Laroze, D.; Fulla, M. R.; Marín, J. H.

2018-05-01

The D2+ molecular complex fundamental properties in a uniform and multi-hilled semiconductor quantum ribbon under orthogonal electric and magnetic fields are theoretically studied. The energy structure is calculated by using adiabatic approximation combined with diagonalization procedure. The D2+ energy structure is more strongly controlled by the geometrical structural hills than the Coulomb interaction. The formation of vibrational and rotational states is discussed. Aharanov-Bohm oscillation patterns linked to rotational states as well as the D2+ molecular complex stability are highly sensitive to the number of hills while electric field breaks the electron rotational symmetry and removes the energy degeneration between low-lying states.

Color Histogram Diffusion for Image Enhancement

NASA Technical Reports Server (NTRS)

Kim, Taemin

2011-01-01

Various color histogram equalization (CHE) methods have been proposed to extend grayscale histogram equalization (GHE) for color images. In this paper a new method called histogram diffusion that extends the GHE method to arbitrary dimensions is proposed. Ranges in a histogram are specified as overlapping bars of uniform heights and variable widths which are proportional to their frequencies. This diagram is called the vistogram. As an alternative approach to GHE, the squared error of the vistogram from the uniform distribution is minimized. Each bar in the vistogram is approximated by a Gaussian function. Gaussian particles in the vistoram diffuse as a nonlinear autonomous system of ordinary differential equations. CHE results of color images showed that the approach is effective.

Functional tooth restoration utilising split germs through re-regionalisation of the tooth-forming field

PubMed Central

Yamamoto, Naomi; Oshima, Masamitsu; Tanaka, Chie; Ogawa, Miho; Nakajima, Kei; Ishida, Kentaro; Moriyama, Keiji; Tsuji, Takashi

2015-01-01

The tooth is an ectodermal organ that arises from a tooth germ under the regulation of reciprocal epithelial-mesenchymal interactions. Tooth morphogenesis occurs in the tooth-forming field as a result of reaction-diffusion waves of specific gene expression patterns. Here, we developed a novel mechanical ligation method for splitting tooth germs to artificially regulate the molecules that control tooth morphology. The split tooth germs successfully developed into multiple correct teeth through the re-regionalisation of the tooth-forming field, which is regulated by reaction-diffusion waves in response to mechanical force. Furthermore, split teeth erupted into the oral cavity and restored physiological tooth function, including mastication, periodontal ligament function and responsiveness to noxious stimuli. Thus, this study presents a novel tooth regenerative technology based on split tooth germs and the re-regionalisation of the tooth-forming field by artificial mechanical force. PMID:26673152

Eating Disorder Risk and the Role of Clothing in Collegiate Cheerleaders' Body Images

PubMed Central

Torres-McGehee, Toni M.; Monsma, Eva V.; Dompier, Thomas P.; Washburn, Stefanie A.

2012-01-01

Context With increased media coverage and competitive opportunities, cheerleaders may be facing an increase in eating disorder (ED) prevalence linked to clothing-related body image (BI). Objective To examine ED risk prevalence, pathogenic weight control behaviors, and variation in clothing-specific BI across position and academic status among collegiate cheerleaders. Design Cross-sectional study. Setting National Collegiate Athletic Association Division I and II institutions. Patients or Other Participants Female collegiate cheerleaders (n = 136, age = 20.4 ± 1.3 years, height = 160.2 ± 8.1 cm, weight = 57.2 ± 8.3 kg). Main Outcome Measure(s) Participants self-reported height, weight, and desired weight and completed the Eating Attitudes Test. Body image perceptions in 3 clothing types (daily clothing, midriff uniform, full uniform) were assessed using sex-based silhouettes (body mass index = 18.3 kg/m2 for silhouette 1, 23.1 kg/m2 for silhouette 4). Results The ED risk for cheerleaders was estimated at 33.1%. However, when body mass index was controlled using backward stepwise logistic regression, flyers had greater odds (odds ratio = 4.4, 95% confidence interval = 1.5, 13.2, P = .008) of being at risk compared with bases, but no difference was noted between the base and back-spot positions (odds ratio = 1.9, 95% confidence interval = 0.5, 6.6, P = .333). A main effect of BI perceptions was seen (P < .001), with a significant interaction by clothing type (F2,133 = 22.5, P < .001, η2 = 0.14). Cheerleaders desired to be smaller than their perceived BIs for each clothing type, with the largest difference for midriff uniform (2.6 ± 0.8 versus 3.7 ± 0.9), followed by full uniform (2.7 ± 0.8 versus 3.5 ± 0.9) and daily clothing (2.8 ± 0.8 versus 3.5 ± 0.9). Conclusions Cheerleaders, especially flyers, appear to be at risk for EDs, with greatest BI dissatisfaction when wearing their most revealing uniforms (ie, midriffs). Universities, colleges, and the national governing bodies of these squads need to focus on preventing eating disorders and BI dissatisfaction and promoting self-esteem. PMID:23068592

Profilometric analysis of two composite resins' surface repolished after tooth brush abrasion with three polishing systems.

PubMed

Uppal, Mudit; Ganesh, Arathi; Balagopal, Suresh; Kaur, Gurleen

2013-07-01

To evaluate the effect of three polishing protocols that could be implemented at recall on the surface roughness of two direct esthetic restorative materials. Specimens (n = 40) measuring 8 mm (length) × 5 mm (width) × 4 mm (height) were fabricated in an acrylic mold using two light-cured resin-based materials (microfilled composite and microhybrid composite). After photopolymerization, all specimens were finished and polished with one of three polishing protocols (Enhance, One Gloss, and Sof-Lex polishing systems). The average surface roughness of each treated specimen was determined using 3D optical profilometer. Next all specimens were brushed 60,000 times with nylon bristles at 7200 rpm using crosshead brushing device with equal parts of toothpaste and water used as abrasive medium. The surface roughness of each specimen was measured after brushing followed by repolishing with one of three polishing protocols, and then, the final surface roughness values were determined. The data were analyzed using one-way and two-factor analysis of variance (ANOVA) and Tukey's honestly significant difference (HSD). Significant difference (P < 0.05) in surface roughness was observed. Simulated brushing following initial polishing procedure significantly roughened the surface of restorative material (P < 0.05). Polishing protocols can be used to restore a smooth surface on esthetic restorative materials following simulated tooth brushing.

Mandibular arch form: the relationship between dental and basal anatomy.

PubMed

Ronay, Valerie; Miner, R Matthew; Will, Leslie A; Arai, Kazuhito

2008-09-01

We investigated mandibular dental arch form at the levels of both the clinically relevant application points of the orthodontic bracket and the underlying anatomic structure of the apical base. The correlation of both forms was evaluated and examined to determine whether the basal arch could be used to derive a standardized clinical arch form. Thirty-five mandibular dental casts (skeletal and dental Class I) were laser scanned, and a 3-dimensional virtual model was created. Two reference points (FA, the most prominent part of the central lobe on each crown's facial surface, and WALA, a point at the height of the mucogingival junction) were selected for each tooth from the right to the left first molars. The FA and WALA arch forms were compared, and the distances between corresponding points and intercanine and intermolar widths were analyzed. Both arch forms were highly individual and the tooth values scattered. Nevertheless, a highly significant relationship between the FA and WALA curves was found, especially in the canine (0.75) and molar (0.87) areas. Both FA and WALA point-derived arch forms were individual and therefore could not be defined by a generalized shape. WALA points proved to be a useful representation of the apical base and helpful in the predetermination of an individualized dental arch form.

Relationship between physical performance and quality of life in Charcot-Marie-Tooth disease: a pilot study.

PubMed

Roberts-Clarke, Daniel; Fornusek, Che; Saigal, Nidhi; Halaki, Mark; Burns, Joshua; Nicholson, Garth; Fiatarone Singh, Maria; Hackett, Daniel

2016-12-01

Charcot-Marie-Tooth (CMT) is a rare inherited peripheral neuropathy in which quality of life (QoL) is reduced compared with the general population. This paper investigates the relationship between QoL and physical performance in people with CMT with the aim of identifying avenues for future research into rehabilitation strategies. Cross-sectional data was obtained from 10 participants (5 men, 5 women, age 46 ± 13 years, height 1.7 ± 0.1 m, body mass 77 ± 17 kg) with CMT (CMT1A n = 5; CMT-X n = 3; unknown genetic origin n = 2). Participants were evaluated for QoL, falls efficacy (FES), balance, mobility, muscle strength, and power. Physical component score (PCS) of the Short Form-36 (SF-36) was significantly and directly related to higher leg press power (r = 0.75, p = 0.02). Better FES scores were significantly related to faster habitual gait speed (r = -0.70, p = 0.02), left hip abduction, and seated row strength (r = -0.68, p = 0.03; r = -0.73, p = 0.03, respectively). Future research should aim to substantiate these preliminary findings in a larger cohort and investigate whether interventions targeting muscle strength and power can improve QoL and mobility outcomes in people with CMT. © 2016 Peripheral Nerve Society.

A simple three-dimensional stent for proper placement of mini-implant

PubMed Central

2013-01-01

Background This paper deals with the fabrication of a three-dimensional stent which is simple in design but provides an accurate placement of a mini-implant in three planes of space, namely, sagittal (root proximity), vertical (attached gingiva/alveolar mucosa) and transverse (angulation). Findings The stent is made of 0.018 × 0.025 in. stainless steel archwire which consists of a ‘u loop’ angulated at 20°, a vertical limb, a horizontal limb and a stop. The angulation of the ‘u’ helps in the placement of the mini-implant at 70° to the long axis of the tooth. The vertical height is determined such that the mini-implant is placed at the mucogingival junction. The mini-implant is placed with the aid of the stent, and its angulation and proximity to the adjacent roots are checked with a cone beam computed tomography image. The cone beam computed tomography image showed the mini-implant at an angle of 70° to the long axis of the tooth. There is no contact between mini-implant and the roots of the adjacent teeth. Conclusion This stent is simple, easy to fabricate, cost-effective, and provides ease of insertion/removal, and three-dimensional orientation of the mini-implant. PMID:24326158

Evolution of high tooth replacement rates in sauropod dinosaurs.

PubMed

D'Emic, Michael D; Whitlock, John A; Smith, Kathlyn M; Fisher, Daniel C; Wilson, Jeffrey A

2013-01-01

Tooth replacement rate can be calculated in extinct animals by counting incremental lines of deposition in tooth dentin. Calculating this rate in several taxa allows for the study of the evolution of tooth replacement rate. Sauropod dinosaurs, the largest terrestrial animals that ever evolved, exhibited a diversity of tooth sizes and shapes, but little is known about their tooth replacement rates. We present tooth replacement rate, formation time, crown volume, total dentition volume, and enamel thickness for two coexisting but distantly related and morphologically disparate sauropod dinosaurs Camarasaurus and Diplodocus. Individual tooth formation time was determined by counting daily incremental lines in dentin. Tooth replacement rate is calculated as the difference between the number of days recorded in successive replacement teeth. Each tooth family in Camarasaurus has a maximum of three replacement teeth, whereas each Diplodocus tooth family has up to five. Tooth formation times are about 1.7 times longer in Camarasaurus than in Diplodocus (315 vs. 185 days). Average tooth replacement rate in Camarasaurus is about one tooth every 62 days versus about one tooth every 35 days in Diplodocus. Despite slower tooth replacement rates in Camarasaurus, the volumetric rate of Camarasaurus tooth replacement is 10 times faster than in Diplodocus because of its substantially greater tooth volumes. A novel method to estimate replacement rate was developed and applied to several other sauropodomorphs that we were not able to thin section. Differences in tooth replacement rate among sauropodomorphs likely reflect disparate feeding strategies and/or food choices, which would have facilitated the coexistence of these gigantic herbivores in one ecosystem. Early neosauropods are characterized by high tooth replacement rates (despite their large tooth size), and derived titanosaurs and diplodocoids independently evolved the highest known tooth replacement rates among archosaurs.

Evolution of High Tooth Replacement Rates in Sauropod Dinosaurs

PubMed Central

Smith, Kathlyn M.; Fisher, Daniel C.; Wilson, Jeffrey A.

2013-01-01

Background Tooth replacement rate can be calculated in extinct animals by counting incremental lines of deposition in tooth dentin. Calculating this rate in several taxa allows for the study of the evolution of tooth replacement rate. Sauropod dinosaurs, the largest terrestrial animals that ever evolved, exhibited a diversity of tooth sizes and shapes, but little is known about their tooth replacement rates. Methodology/Principal Findings We present tooth replacement rate, formation time, crown volume, total dentition volume, and enamel thickness for two coexisting but distantly related and morphologically disparate sauropod dinosaurs Camarasaurus and Diplodocus. Individual tooth formation time was determined by counting daily incremental lines in dentin. Tooth replacement rate is calculated as the difference between the number of days recorded in successive replacement teeth. Each tooth family in Camarasaurus has a maximum of three replacement teeth, whereas each Diplodocus tooth family has up to five. Tooth formation times are about 1.7 times longer in Camarasaurus than in Diplodocus (315 vs. 185 days). Average tooth replacement rate in Camarasaurus is about one tooth every 62 days versus about one tooth every 35 days in Diplodocus. Despite slower tooth replacement rates in Camarasaurus, the volumetric rate of Camarasaurus tooth replacement is 10 times faster than in Diplodocus because of its substantially greater tooth volumes. A novel method to estimate replacement rate was developed and applied to several other sauropodomorphs that we were not able to thin section. Conclusions/Significance Differences in tooth replacement rate among sauropodomorphs likely reflect disparate feeding strategies and/or food choices, which would have facilitated the coexistence of these gigantic herbivores in one ecosystem. Early neosauropods are characterized by high tooth replacement rates (despite their large tooth size), and derived titanosaurs and diplodocoids independently evolved the highest known tooth replacement rates among archosaurs. PMID:23874921

Effects of Shrouded Stator Cavity Flows on Multistage Axial Compressor Aerodynamic Performance

NASA Technical Reports Server (NTRS)

Wellborn, Steven R.; Okiishi, Theodore H.

1996-01-01

Experiments were performed on a low-speed multistage axial-flow compressor to assess the effects of shrouded stator cavity flows on aerodynamic performance. Five configurations, which involved changes in seal-tooth leakage rates and/or elimination of the shrouded stator cavities, were tested. Data collected enabled differences in overall individual stage and the third stage blade element performance parameters to be compared. The results show conclusively that seal-tooth leakage ran have a large impact on compressor aerodynamic performance while the presence of the shrouded stator cavities alone seemed to have little influence. Overall performance data revealed that for every 1% increase in the seal-tooth clearance to blade-height ratio the pressure rise dropped up to 3% while efficiency was reduced by 1 to 1.5 points. These observed efficiency penalty slopes are comparable to those commonly reported for rotor and cantilevered stator tip clearance variations. Therefore, it appears that in order to correctly predict overall performance it is equally important to account for the effects of seal-tooth leakage as it is to include the influence of tip clearance flows. Third stage blade element performance data suggested that the performance degradation observed when leakage was increased was brought about in two distinct ways. First, increasing seal-tooth leakage directly spoiled the near hub performance of the stator row in which leakage occurred. Second, the altered stator exit now conditions caused by increased leakage impaired the performance of the next downstream stage by decreasing the work input of the downstream rotor and increasing total pressure loss of the downstream stator. These trends caused downstream stages to progressively perform worse. Other measurements were acquired to determine spatial and temporal flow field variations within the up-and-downstream shrouded stator cavities. Flow within the cavities involved low momentum fluid traveling primarily in the circumferential direction at about 40% of the hub wheel speed. Measurements indicated that the flow within both cavities was much more complex than first envisioned. A vortical flow structure in the meridional plane, similar to a driven cavity, existed within the upstream cavity Furthermore, other spatial and temporal variations in Row properties existed. the most prominent being caused by the upstream potential influence of the downstream blade. This influence caused the fluid within cavities near the leading edges of either stator blades in space or rotor blades in time to be driven radially inward relative to fluid near blade mid-pitch. This influence also produced large unsteady velocity fluctuations in the downstream cavity because of the passing of the downstream rotor blade.

Effects of different types of tooth movement and force magnitudes on the amount of tooth movement and root resorption in rats.

PubMed

Nakano, Takako; Hotokezaka, Hitoshi; Hashimoto, Megumi; Sirisoontorn, Irin; Arita, Kotaro; Kurohama, Takeshi; Darendeliler, M Ali; Yoshida, Noriaki

2014-11-01

To investigate differences in the amount of tooth movement and root resorption that occurred after tipping and bodily movement of the maxillary first molar in rats. Ten-week-old female Wistar rats were divided into two groups according to type of tooth movement and subdivided into four subgroups according to the magnitude of applied force. Nickel-titanium closed-coil springs exerting forces of 10, 25, 50, or 100 g were applied to the maxillary left first molars to induce mesial tooth movement. We designed a novel orthodontic appliance for bodily tooth movement. Tooth movement distance and root resorption were measured using microcomputed tomography and scanning electron and scanning laser microscopy. The amount of tooth movement in the bodily tooth movement group was less than half that in the tipping tooth movement group. The greatest amount of tooth movement occurred in the 10-g tipping and 50-g bodily tooth movement subgroups, and the amount of tooth movement decreased with the application of an excessive magnitude of force. Conversely, root resorption increased when the heavier orthodontic force was applied in both groups. Root resorption in the tipping tooth movement group was approximately twice that in the bodily tooth movement group. Root resorption in the tipping tooth movement group was more pronounced than that in the bodily tooth movement group. Although the amount of tooth movement decreased when extremely heavy forces were applied, root resorption increased in both the tipping and bodily tooth movement groups in rats.

New reversing freeform lens design method for LED uniform illumination with extended source and near field

NASA Astrophysics Data System (ADS)

Zhao, Zhili; Zhang, Honghai; Zheng, Huai; Liu, Sheng

2018-03-01

In light-emitting diode (LED) array illumination (e.g. LED backlighting), obtainment of high uniformity in the harsh condition of the large distance height ratio (DHR), extended source and near field is a key as well as challenging issue. In this study, we present a new reversing freeform lens design algorithm based on the illuminance distribution function (IDF) instead of the traditional light intensity distribution, which allows uniform LED illumination in the above mentioned harsh conditions. IDF of freeform lens can be obtained by the proposed mathematical method, considering the effects of large DHR, extended source and near field target at the same time. In order to prove the claims, a slim direct-lit LED backlighting with DHR equal to 4 is designed. In comparison with the traditional lenses, illuminance uniformity of LED backlighting with the new lens increases significantly from 0.45 to 0.84, and CV(RMSE) decreases dramatically from 0.24 to 0.03 in the harsh condition. Meanwhile, luminance uniformity of LED backlighting with the new lens is obtained as high as 0.92 at the condition of extended source and near field. This new method provides a practical and effective way to solve the problem of large DHR, extended source and near field for LED array illumination.

Image analysis of the eruptive positions of third molars and adjacent second molars as indicators of age evaluation in Thai patients

PubMed Central

Pramojanee, Sakarat; Thaiupathump, Trasapong

2013-01-01

Purpose This study was performed to determine the relationship between the stage of tooth eruption (both vertical and mesio-angular) and chronological age. Materials and Methods Indirect digital panoramic radiographs were used to measure the distances from the dentinoenamel junction (DEJ) of the second molars to the occlusal plane of the second molar teeth and of the adjacent third molars in 264 Thai males and 437 Thai females using ImageJ software. The ratio of those distances was calculated by patient age, and the correlation coefficient of the ratio of the third molar length to the second molar length was calculated. Results The correlation between the height of the vertically erupted upper third molar teeth and age was at the intermediate level. The age range of ≥15 to <16 years was noted to be the range in which the correlation between the chronological age determined from the eruptional height and actual chronological age was statistically significant. The mean age of the female subjects, in which the position of the right upper third molar teeth was at or above the DEJ of the adjacent second molar but below one half of its coronal height was 19.9±2.6 years. That for the left side was 20.2±2.7 years. The mean ages of the male subjects were 20.1±3.3 years and 19.8±2.7 years for the right and left sides, respectively. Conclusion It might be possible to predict chronological age from the eruption height of the wisdom teeth. PMID:24380069

Biomaterial Selection for Tooth Regeneration

PubMed Central

Yuan, Zhenglin; Nie, Hemin; Wang, Shuang; Lee, Chang Hun; Li, Ang; Fu, Susan Y.; Zhou, Hong

2011-01-01

Biomaterials are native or synthetic polymers that act as carriers for drug delivery or scaffolds for tissue regeneration. When implanted in vivo, biomaterials should be nontoxic and exert intended functions. For tooth regeneration, biomaterials have primarily served as a scaffold for (1) transplanted stem cells and/or (2) recruitment of endogenous stem cells. This article critically synthesizes our knowledge of biomaterial use in tooth regeneration, including the selection of native and/or synthetic polymers, three-dimensional scaffold fabrication, stem cell transplantation, and stem cell homing. A tooth is a complex biological organ. Tooth loss represents the most common organ failure. Tooth regeneration encompasses not only regrowth of an entire tooth as an organ, but also biological restoration of individual components of the tooth including enamel, dentin, cementum, or dental pulp. Regeneration of tooth root represents perhaps more near-term opportunities than the regeneration of the whole tooth. In the adult, a tooth owes its biological vitality, arguably more, to the root than the crown. Biomaterials are indispensible for the regeneration of tooth root, tooth crown, dental pulp, or an entire tooth. PMID:21699433

Pressure regulator

DOEpatents

Ebeling, Jr., Robert W.; Weaver, Robert B.

1979-01-01

The pressure within a pressurized flow reactor operated under harsh environmental conditions is controlled by establishing and maintaining a fluidized bed of uniformly sized granular material of selected density by passing the gas from the reactor upwardly therethrough at a rate sufficient to fluidize the bed and varying the height of the bed by adding granular material thereto or removing granular material therefrom to adjust the backpressure on the flow reactor.

The effects of sower and bed density on bareroot loblolly pine seedling morphology and early height growth

Treesearch

Hans M. Williams; Tim Stewart

2006-01-01

Precision sowing is commonly used at forest tree nurseries in order to improve the growing space uniformity of seedlings in the beds. Temple-Inland Forest Products Corporation recently purchased a vacuum sower and requested a study be conducted comparing their new sower with a drill sower on the morphological characteristics of loblolly pine (Pinus taeda...

Development of epicormic sprouts in Sitka spruce following thinning and pruning in south-east Alaska.

Treesearch

Robert L. Deal; R. James Barbour; Michael H. McClellan; Dean L. Parry

2003-01-01

The frequency and size of epicormic sprouts in Sitka spruce (Picea sitchensis (Bong.) Carr.) were assessed in five 23-29 year-old mixed Sitka spruce-western hemlock (Tsuga heterophylla (Raf.) Sarg.) stands that were uniformly thinned and pruned to 2.4, 3.7 and 5.2 m lift heights. Six to nine years after treatment sprouts were...

Results after 20 years from a western larch levels-of-growing-stock study.

Treesearch

K.W. Seidel

1987-01-01

The 20-year growth response from a levels-of-growing-stock study in an even-aged western larch stand in eastern Oregon, first thinned at age 33, showed that trees growing at low stand densities grew more rapidly in diameter than trees in high-density plots. Height growth was relatively uniform among density levels. Both basal-area and total cubic-volume increment...

Simulating and sampling the hardwood component of loblolly pine plantations. In: Wensel, L.C.; Biging, G.S., tech

Treesearch

David Weise; G.R. Glover

1990-01-01

The hardwood component of young loblolly pine (Pinus taeda L.) plantations was simulated for use in a sampling study of competing vegetation. Spatial arrangement, total height, and crown area of hardwood rootstocks in 19 plantations 3 to 6 years old in Alabama and Georgia were used to develop the simulator. Rootstock arrangement ranged from uniform...

A modified S-DIMM+: applying additional height grids for characterizing daytime seeing profiles

NASA Astrophysics Data System (ADS)

Wang, Zhiyong; Zhang, Lanqiang; Kong, Lin; Bao, Hua; Guo, Youming; Rao, Xuejun; Zhong, Libo; Zhu, Lei; Rao, Changhui

2018-07-01

Characterization of daytime atmospheric turbulence profiles is needed for the design of a multi-conjugate adaptive optical system. S-DIMM+ (solar differential image motion monitor+) is a technique to measure vertical seeing profiles. However, the number of height grids will be limited by the lenslet array of the wide-field Shack-Hartmann wavefront sensor (SHWFS). A small number of subaperture lenslet arrays will lead to a coarse height grid over the atmosphere, which can result in difficulty in finding the location of strong-turbulence layers and overestimates of the turbulence strength for the measured layers. To address this problem, we propose a modified S-DIMM+ method to measure seeing profiles iteratively with decreasing altitude range for a given number of height grids; finally they will be combined as a new seeing profile, with a denser and more uniform distribution of height grids. This method is tested with simulations and recovers the input height and contribution perfectly. Furthermore, this method is applied to the 102 data-sequences recorded from the 1-m New Vacuum Solar Telescope at Fuxian Solar Observatory, 55 of which were recorded at local time between 13:40 and 14:35 on 2016 October 6, and the other 47 between 12:50 and 13:40 on 2017 October 5. A 7x7 lenslet array of SHWFS is used to generate a 16-layer height grid to 15 km, each with 1 km height separation. The experimental results show that the turbulence has three origins in the lower (0-2 km) layers, the higher (3-6 km) layers and the uppermost (≥7 km) layers.

Recuperator construction for a gas turbine engine

DOEpatents

Kang, Yungmo; McKeirnan, Jr., Robert D.

2006-12-12

A counter-flow recuperator formed from annular arrays of recuperator core segments. The recuperator core segments are formed from two opposing sheets of fin fold material coined to form a primary surface zone disposed between two flattened manifold zones. Each primary surface zone has undulating corrugations including a uniform, full height central portion and a transition zone disposed between the central portion and one of the manifold zones. Corrugations of the transition zone rise from zero adjacent to the manifold zone and increase along a transition length to full crest height at the central portion. The transition lengths increase in a direction away from an inner edge containing the air inlet so as to equalize air flow to the distal regions of the primary surface zone.

The prevalence of tooth discolouration and the self-satisfaction with tooth colour in a Chinese urban population.

PubMed

Xiao, J; Zhou, X D; Zhu, W C; Zhang, B; Li, J Y; Xu, X

2007-05-01

To determine the prevalence of tooth discolouration, self-satisfaction with tooth colour, and correlation with socio-demographic-behavioural factors in adults and teenagers in Chengdu, China. A cross-sectional survey. 405 Chinese urban adults and teenagers from a multistage random probability sample. Tooth colour was measured on the maxillary central incisors using a colorimeter. Tooth discolouration was determined according to the discolouration level figure and evaluation criteria. Self-satisfaction with tooth colour was assessed on a five-point qualitative scale. Data were coded and analyzed using SPSS software. The mean values for L*, a* and b* were 70.67 (s.d. 1.91), 4.29 (s.d. 2.05) and 17.51 (s.d. 4.13), respectively. Age and sex were the most important factors associated with tooth colour (P < 0.05). About half of the study population (48.9%) suffered from some tooth discolouration, and 52.6% were dissatisfied with their tooth colour. Education and smoking were significant factors affecting self-satisfaction with tooth colour (P < 0.05). Tooth discolouration is common among the Chinese, and many Chinese are dissatisfied with their tooth colour. Self-satisfaction with tooth colour decreased with increasing severity of discolouration. Further research is needed to determine types of tooth discolouration among broader regions in China.

Outcomes and stability in patients with anterior open bite and long anterior face height treated with temporary anchorage devices and a maxillary intrusion splint

PubMed Central

Scheffler, Nicole R.; Proffit, William R.; Phillips, Ceib

2015-01-01

Introduction Temporary skeletal anchorage devices now offer the possibility of closing anterior open bites and decreasing anterior face height by intruding maxillary posterior teeth, but data for treatment outcomes are lacking. This article presents outcomes and posttreatment changes for consecutive patients treated with a standardized technique. Methods The sample included 33 consecutive patients who had intrusion of maxillary posterior teeth with a maxillary occlusal splint and nickel-titanium coil springs to temporary anchorage devices in the zygomatic buttress area, buccal and apical to the maxillary molars. Of this group, 30 had adequate cephalograms available for the period of treatment, 27 had cephalograms including 1-year posttreatment, and 25 had cephalograms from 2 years or longer. Results During splint therapy, the mean molar intrusion was 2.3 mm. The mean decrease in anterior face height was 1.6 mm, less than expected because of a 0.6-mm mean eruption of the mandibular molars. During the postintrusion orthodontics, the mean change in maxillary molar position was a 0.2-mm extrusion, and there was a mean 0.5-mm increase in face height. Positive overbite was maintained in all patients, with a slight elongation (<2 mm) of the incisors contributing to this. During the 1 year of posttreatment retention, the mean changes were a further eruption of 0.5 mm of the maxillary molars, whereas the mandibular molars intruded by 0.6 mm, and there was a small decrease in anterior face height. Changes beyond 1 year posttreatment were small and attributable to growth rather than relapse in tooth positions. Conclusions Intrusion of the maxillary posterior teeth can give satisfactory correction of moderately severe anterior open bites, but 0.5 to 1.5 mm of reeruption of these teeth is likely to occur. Controlling the vertical position of the mandibular molars so that they do not erupt as the maxillary teeth are intruded is important in obtaining a decrease in face height. PMID:25439210

[Effect of a tooth-brushing education program on oral health of preschool children].

PubMed

Kang, Bok-Hee; Park, Sun-Nam; Sohng, Kyeong-Yae; Moon, Jung-Soon

2008-12-01

To examine the effect of tooth-brushing education on the oral health of preschoolers. A quasi-experimental design with a non-equivalent control group was used. Two kindergartens were selected and 39 preschoolers from one kindergarten were assigned to the experimental group with tooth-brushing education and 39 from the other kindergarten to the control group. The tooth-brushing education program included 1 session on oral health education, individual tooth-brushing instruction for 1 week and supervised tooth-brushing after lunch for 4 weeks. Oral health behavior including use of tooth paste, tooth-brushing time and method of tooth-brushing, plague, streptococcus mutans, lactobacillus and dental caries were measured before and after the education. Fisher's exact test, t-test and paired t-test with the Window SAS 9.1 program were used to analyze the data. A significant increase in the use of tooth paste, tooth-brushing time and the practice of correct tooth-brushing and a decrease in plague and development of dental caries were observed in the experimental group. This tooth-brushing education was partially effective in improving oral health of preschoolers.

Surfzone vorticity in the presence of extreme bathymetric variability

NASA Astrophysics Data System (ADS)

Clark, D.; Elgar, S.; Raubenheimer, B.

2014-12-01

Surfzone vorticity was measured at Duck, NC using a novel 5-m diameter vorticity sensor deployed in 1.75 m water depth. During the 4-week deployment the initially alongshore uniform bathymetry developed 200-m long mega-cusps with alongshore vertical changes of 1.5 m or more. When waves were small and the vorticity sensor was seaward of the surfzone, vorticity variance and mean vorticity varied with the tidally modulated water depth, consistent with a net seaward flux of surfzone-generated vorticity. Vorticity variance increased with incident wave heights up to 2-m. However, vorticity variance remained relatively constant for incident wave heights above 2-m, and suggests that eddy energy may become saturated in the inner surfzone during large wave events. In the presence of mega-cusps the mean vorticity (shear) is often large and generated by bathymetrically controlled rip currents, while vorticity variance remains strongly correlated with the incident wave height. Funded by NSF, ASD(R&E), and WHOI Coastal Ocean Institute.

A note on ``critical roughness height'' and ``transitional roughness''

NASA Astrophysics Data System (ADS)

Bradshaw, P.

2000-06-01

An unrigorous but plausible analysis suggests that the concept of a critical roughness height, below which roughness does not affect a turbulent wall flow, is erroneous. The Oseen approximation implies that the effect of roughness on the additive constant in the logarithmic law of the wall should vary as the square of the roughness Reynolds number (specifically the roughness height in "wall units"). This is an important point in determining whether surfaces used in experiments at high unit Reynolds number can be regarded as hydraulically smooth. Attention is also called to the qualitative difference between Nikuradse's measurements of friction factor in pipe flow with uniform-size sand-grain roughness in the "transitional" range of Reynolds number and the data correlation in the Moody chart of 1944; the latter was derived from tests on miscellaneous real-life rough surfaces in the 1930s. Nearly all textbooks on elementary fluid dynamics present, but practically none discuss, this difference. Nikuradse's monodisperse roughness is a very rare case with untypical behavior in the transitional range.

Time dependent changes in Schottky barrier mapping of the W/Si(001) interface utilizing ballistic electron emission microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Durcan, Chris A.; Balsano, Robert; LaBella, Vincent P., E-mail: vlabella@albany.edu

2015-06-28

The W/Si(001) Schottky barrier height is mapped to nanoscale dimensions using ballistic electron emission microscopy (BEEM) over a period of 21 days to observe changes in the interface electrostatics. Initially, the average spectrum is fit to a Schottky barrier height of 0.71 eV, and the map is uniform with 98% of the spectra able to be fit. After 21 days, the average spectrum is fit to a Schottky barrier height of 0.62 eV, and the spatial map changes dramatically with only 27% of the spectra able to be fit. Transmission electron microscopy shows the formation of an ultra-thin tungsten silicide at themore » interface, which increases in thickness over the 21 days. This increase is attributed to an increase in electron scattering and the changes are observed in the BEEM measurements. Interestingly, little to no change is observed in the I-V measurements throughout the 21 day period.« less

Bioengineered Tooth Buds Exhibit Features of Natural Tooth Buds.

PubMed

Smith, E E; Angstadt, S; Monteiro, N; Zhang, W; Khademhosseini, A; Yelick, P C

2018-06-01

Tooth loss is a significant health issue currently affecting millions of people worldwide. Artificial dental implants, the current gold standard tooth replacement therapy, do not exhibit many properties of natural teeth and can be associated with complications leading to implant failure. Here we propose bioengineered tooth buds as a superior alternative tooth replacement therapy. We describe improved methods to create highly cellularized bioengineered tooth bud constructs that formed hallmark features that resemble natural tooth buds such as the dental epithelial stem cell niche, enamel knot signaling centers, transient amplifying cells, and mineralized dental tissue formation. These constructs were composed of postnatal dental cells encapsulated within a hydrogel material that were implanted subcutaneously into immunocompromised rats. To our knowledge, this is the first report describing the use of postnatal dental cells to create bioengineered tooth buds that exhibit evidence of these features of natural tooth development. We propose future bioengineered tooth buds as a promising, clinically relevant tooth replacement therapy.

Finite element analysis of maxillary incisor displacement during en-masse retraction according to orthodontic mini-implant position

PubMed Central

Song, Jae-Won; Lim, Joong-Ki; Lee, Kee-Joon; Sung, Sang-Jin; Chun, Youn-Sic

2016-01-01

Objective Orthodontic mini-implants (OMI) generate various horizontal and vertical force vectors and moments according to their insertion positions. This study aimed to help select ideal biomechanics during maxillary incisor retraction by varying the length in the anterior retraction hook (ARH) and OMI position. Methods Two extraction models were constructed to analyze the three-dimentional finite element: a first premolar extraction model (Model 1, M1) and a residual 1-mm space post-extraction model (Model 2, M2). The OMI position was set at a height of 8 mm from the arch wire between the second maxillary premolar and the first molar (low OMI traction) or at a 12-mm height in the mesial second maxillary premolar (high OMI traction). Retraction force vectors of 200 g from the ARH (-1, +1, +3, and +6 mm) at low or high OMI traction were resolved into X-, Y-, and Z-axis components. Results In M1 (low and high OMI traction) and M2 (low OMI traction), the maxillary incisor tip was extruded, but the apex was intruded, and the occlusal plane was rotated clockwise. Significant intrusion and counter-clockwise rotation in the occlusal plane were observed under high OMI traction and -1 mm ARH in M2. Conclusions This study observed orthodontic tooth movement according to the OMI position and ARH height, and M2 under high OMI traction with short ARH showed retraction with maxillary incisor intrusion. PMID:27478801

[The effect of cervical headgear and lower utility arch on the control of vertical dimension in tooth and jaw].

PubMed

Zhang, Li; Luo, Ying; Wang, Ren-fei

2010-08-01

To evaluate the effect of cervical headgear and lower utility arch in growing skeletal Class II division 1 patients. The patients were divided into 3 groups, the first group was treated with cervical headgear alone (n=20), the second group was treated with cervical headgear and lower utility arch (n=20), and the third group was a control group without treatment (n=20). Cephalometric radiographs were taken and analyzed with SPSS15.0 software package. Student's t test was used to determine if there was significant difference among the 3 groups. Anterior facial height and ramus height displayed significantly increase in the treatment groups than those in the control group; the lower utility arch produced intrusion and lingual tipping of the mandibular incisors and distal tipping without extrusion of the mandibular molars; compared with the control group, maxillary molar total extrusion produced by cervical headgear treatment was not more than 1mm at average. The treatment groups show significant reduction in maxillary protrusion; significant increase in the anterior descent of the PP and ramus height, as a result, mandibular plane orientation is relatively unchanged. The treatment groups have maxillary molar extrusion less than 1mm, which can be considered clinically not significant. The lower utility arch produces mandibular incisor intrusion and lingual tipping, the mandibular molars tip distally without extrusion, the lower utility arch does not influence the mandibular rotation.

Dentoalveolar development in subjects with normal occlusion. A longitudinal study between the ages of 5 and 31 years.

PubMed

Thilander, Birgit

2009-04-01

The aim of the present study was to examine dentoalveolar development in subjects with an 'ideal' (normal) occlusion. The material comprised 436 study casts of 189 male and 247 female subjects of Swedish origin between the ages of 5 and 31 years with no history of orthodontic treatment. Tooth width, and arch length, width, and depth, as well as palatal height were measured. The data were analysed with a Student's t-test. The results verified that continuous changes of the dental arches occur from the primary until the adult period, with individual variations. This change could be interpreted as a biological migration of the dentition, resulting in anterior crowding especially in the mandible, even in subjects with congenitally missing third molars. The occlusion should be regarded as a dynamic rather than a stable interrelationship between facial structures. This natural development has to be considered in orthodontic treatment planning as well as in assessment of stability following orthodontic treatment. A continuous increase of palatal height up to adulthood seems to be an effect of a slow continuous eruption of the teeth. This finding is also of significance in explaining the infraposition of implant-supported crowns.

[Tooth wear, a proposal for an evaluation system].

PubMed

Wetselaar, P; van der Zaag, J; Lobbezoo, F

2011-06-01

The present-day terminology and definitions of tooth wear are not unambiguous. For diagnosing tooth wear, however, it is essential that they are unambiguous. In this article a proposal is presented for a tooth wear evaluation system with simplified definitions. This system consists ofa number of modules and can be used for various aspects of the diagnostic procedure. It can be used for the quantification of tooth wear, both for periodic screening and for the monitoring of tooth wear in individual patients. The scoring of occlusal/incisal tooth wear as well as of non-occlusal/non-incisal tooth wear is possible. The evaluative system is also suitable for determining which type of tooth wear, such as attrition, abrasion and erosion, is most likely to have caused any observed loss of hard tooth tissue.

One-step fabrication of nanostructure-covered microstructures using selective aluminum anodization based on non-uniform electric field

NASA Astrophysics Data System (ADS)

Park, Yong Min; Kim, Byeong Hee; Seo, Young Ho

2016-06-01

This paper presents a selective aluminum anodization technique for the fabrication of microstructures covered by nanoscale dome structures. It is possible to fabricate bulging microstructures, utilizing the different growth rates of anodic aluminum oxide in non-uniform electric fields, because the growth rate of anodic aluminum oxide depends on the intensity of electric field, or current density. After anodizing under a non-uniform electric field, bulging microstructures covered by nanostructures were fabricated by removing the residual aluminum layer. The non-uniform electric field induced by insulative micropatterns was estimated by computational simulations and verified experimentally. Utilizing computational simulations, the intensity profile of the electric field was calculated according to the ratio of height and width of the insulative micropatterns. To compare computational simulation results and experimental results, insulative micropatterns were fabricated using SU-8 photoresist. The results verified that the shape of the bottom topology of anodic alumina was strongly dependent on the intensity profile of the applied electric field, or current density. The one-step fabrication of nanostructure-covered microstructures can be applied to various fields, such as nano-biochip and nano-optics, owing to its simplicity and cost effectiveness.

Rapid fabrication of three-dimensional structures for dielectrophoretic sorting of lipid-containing organisms

NASA Astrophysics Data System (ADS)

Schor, Alisha R.; Buie, Cullen R.

2016-10-01

In this work, we demonstrate a microfluidic particle sorter consisting of three-dimensional, conducting microposts. Our sorter uses dielectrophoresis (DEP) to sort high- and low-lipid phenotypes of the yeast Yarrowia lipolytica. Y. lipolytica is one of the many microorganisms being explored as a hydrocarbon source for biodiesel, Omega-3 additives, and other products derived from fatty acids. A rapid, non-destructive, lipid-based sorting tool would accelerate the commercialization of these products. Our device consists of an array of 105, 25 μm wide gold microposts that span the height of a 15 μm channel. This array generates an electric field in a microfluidic device that is uniform through the channel height, but has a custom-shaped non-uniformity in the horizontal directions. This is crucial in order to achieve continuous sorting using DEP, as it ensures all cells are exposed to the same conditions throughout the channel height. By using very low currents (100 μA), we are able to electroplate these post arrays in fewer than 15 min. This is an order of magnitude improvement over previous reports of electroplated microstructures. With an applied signal of 250 MHz, 2.6 V pp in our device, we separate a heterogeneous population with a purity of 97.8% in the low-lipid stream and 71.4% in the high-lipid stream. The high-lipid stream purity can be improved by adjusting the spacing of the array. This unique protocol for the rapid fabrication of 3D microstructures has enabled the creation of a non-invasive sorting tool for genetically engineered, lipid-producing organisms. The ability to screen organisms based on lipid content will alleviate one of the major bottlenecks in commercialization of microbial biofuels.

Positioning the actual interference fringe pattern on the tooth flank in measuring gear tooth flanks by laser interferometry

NASA Astrophysics Data System (ADS)

Fang, Suping; Wang, Leijie; Liu, Shiqiao; Komori, Masaharu; Kubo, Aizoh

2011-05-01

In measuring form deviation of gear tooth flanks by laser interferometry, the collected interference fringe pattern (IFP) is badly distorted, in the case of shape, relative to the actual tooth flank. Meanwhile, a clear and definite mapping relationship between the collected IFP and the actual tooth flank is indispensable for both transforming phase differences into deviation values and positioning the measurement result on the actual tooth flank. In order to solve these problems, this paper proposes a method using the simulation tooth image as a bridge connecting the actual tooth flank and the collected IFP. The mapping relationship between the simulation tooth image and the actual tooth flank has been obtained by ray tracing methods [Fang et al., Appl. Opt. 49(33), 6409-6415 (2010)]. This paper mainly discusses how to build the relationship between the simulation tooth image and the collected IFP by using a matching algorithm of two characteristic point sets. With the combination of the two above-mentioned assistant mapping relationships, the mapping relationship between the collected IFP and the actual tooth flank can be built; the collected IFP can be positioned on the actual tooth flank. Finally, the proposed method is employed in a measurement of the form deviation of a gear tooth flank and the result proves the feasibility of the proposed method.

Tailored Height Gradients in Vertical Nanowire Arrays via Mechanical and Electronic Modulation of Metal-Assisted Chemical Etching.

PubMed

Otte, M A; Solis-Tinoco, V; Prieto, P; Borrisé, X; Lechuga, L M; González, M U; Sepulveda, B

2015-09-02

In current top-down nanofabrication methodologies the design freedom is generally constrained to the two lateral dimensions, and is only limited by the resolution of the employed nanolithographic technique. However, nanostructure height, which relies on certain mask-dependent material deposition or etching techniques, is usually uniform, and on-chip variation of this parameter is difficult and generally limited to very simple patterns. Herein, a novel nanofabrication methodology is presented, which enables the generation of high aspect-ratio nanostructure arrays with height gradients in arbitrary directions by a single and fast etching process. Based on metal-assisted chemical etching using a catalytic gold layer perforated with nanoholes, it is demonstrated how nanostructure arrays with directional height gradients can be accurately tailored by: (i) the control of the mass transport through the nanohole array, (ii) the mechanical properties of the perforated metal layer, and (iii) the conductive coupling to the surrounding gold film to accelerate the local electrochemical etching process. The proposed technique, enabling 20-fold on-chip variation of nanostructure height in a spatial range of a few micrometers, offers a new tool for the creation of novel types of nano-assemblies and metamaterials with interesting technological applications in fields such as nanophotonics, nanophononics, microfluidics or biomechanics. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Satisfaction with appearance and the desired treatment to improve aesthetics.

PubMed

Al-Zarea, Bader K

2013-01-01

Objective. To identify participants' satisfaction with appearance and the desired treatment to improve aesthetics. Materials and Methods. 220 participants (127 males and 93 females, mean age = 21.4 ± 1.5 years) were recruited into the study. A structured questionnaire was used to assess patients' satisfaction with appearance and what treatment they desire to improve aesthetics. Participants scored the level of satisfaction with appearance using visual analogue scale. Results. The VAS mean score of satisfaction with general appearance was 6.8 ± 2.3. Half participants were dissatisfied with tooth appearance and 65.9% were dissatisfied with tooth colour. Higher VAS scores were associated with higher desire for all treatments that improve tooth appearance (P < .05). Dissatisfaction with tooth appearance increased with increased dissatisfaction with teeth colour, feeling of poor tooth alignment, presence of fractured anterior teeth, and increased desire for orthodontic, crowns, and dentures treatments (P < .05). Dissatisfaction with tooth colour was associated with increased desire for tooth whitening and tooth coloured fillings (P < .05). Conclusions. Participants had high levels of dissatisfaction with tooth appearance and tooth colour. Dissatisfaction with tooth colour contributed to the increased dissatisfaction with tooth appearance. Dissatisfaction with tooth appearance, colour, alignment, and condition was significantly related to high desire for aesthetic treatments.

A numerical algorithm of tooth profile of non-circular cylindrical gear

NASA Astrophysics Data System (ADS)

Wang, Xuan

2017-08-01

Non-circular cylindrical gear (NCCG) is a common form of non-circular gear. Different from the circular gear, the tooth profile equation of NCCG cannot be obtained. So it is necessary to use a numerical algorithm to calculate the tooth profile of NCCG. For this reason, this paper presents a simple and highly efficient numerical algorithm to obtain the tooth profile of NCCG. Firstly, the mathematical model of tooth profile envelope of NCCG is established based on the principle of gear shaping, and the tooth profile envelope of NCCG is obtained. Secondly, the polar radius and polar angle of shaper cutter tooth profile are chosen as the criterions, by which the points of NCCG tooth cogging can be screened out. Finally, the boundary of tooth cogging points is extracted by a distance criterion and correspondingly the tooth profile of NCCG is obtained.

Practical whole-tooth restoration utilizing autologous bioengineered tooth germ transplantation in a postnatal canine model

PubMed Central

Ono, Mitsuaki; Oshima, Masamitsu; Ogawa, Miho; Sonoyama, Wataru; Hara, Emilio Satoshi; Oida, Yasutaka; Shinkawa, Shigehiko; Nakajima, Ryu; Mine, Atsushi; Hayano, Satoru; Fukumoto, Satoshi; Kasugai, Shohei; Yamaguchi, Akira; Tsuji, Takashi; Kuboki, Takuo

2017-01-01

Whole-organ regeneration has great potential for the replacement of dysfunctional organs through the reconstruction of a fully functional bioengineered organ using three-dimensional cell manipulation in vitro. Recently, many basic studies of whole-tooth replacement using three-dimensional cell manipulation have been conducted in a mouse model. Further evidence of the practical application to human medicine is required to demonstrate tooth restoration by reconstructing bioengineered tooth germ using a postnatal large-animal model. Herein, we demonstrate functional tooth restoration through the autologous transplantation of bioengineered tooth germ in a postnatal canine model. The bioengineered tooth, which was reconstructed using permanent tooth germ cells, erupted into the jawbone after autologous transplantation and achieved physiological function equivalent to that of a natural tooth. This study represents a substantial advancement in whole-organ replacement therapy through the transplantation of bioengineered organ germ as a practical model for future clinical regenerative medicine. PMID:28300208

Management of localized advance loss of periodontal support associated Grade II furcation and intrabony defect in chronic periodontitis patient through amalgamation of platelet-rich fibrin and hydroxyapatite bioactive glass composite granules.

PubMed

Salaria, Sanjeev Kumar; Ghuman, Simrat Kaur; Kumar, Saurabh; Sharma, Garima

2016-01-01

Periodontal disease is infectious, complex, multifactorial, chronic inflammatory disease of supporting periodontal tissues that not only alters the bone morphology but also leads to the reduction in bone height. Different types of bony deformities such as horizontal, vertical, craters, and furcation result from periodontal disease, but vertical and Grade II furcation defects are more amenable to regenerative periodontal therapy. The present case report describes the current concept of periodontal diagnosis and the clinical radiographical efficiency of platelet-rich fibrin and hydroxyapatite bioactive glass composite granules graft combination in the management of localized advance osseous defects with respect to tooth number 36 in chronic periodontitis patient at 1 year postoperatively.

Tooth-meshing-harmonic static-transmission-error amplitudes of helical gears

NASA Astrophysics Data System (ADS)

Mark, William D.

2018-01-01

The static transmission errors of meshing gear pairs arise from deviations of loaded tooth working surfaces from equispaced perfect involute surfaces. Such deviations consist of tooth-pair elastic deformations and geometric deviations (modifications) of tooth working surfaces. To a very good approximation, the static-transmission-error tooth-meshing-harmonic amplitudes of helical gears are herein expressed by superposition of Fourier transforms of the quantities: (1) the combination of tooth-pair elastic deformations and geometric tooth-pair modifications and (2) fractional mesh-stiffness fluctuations, each quantity (1) and (2) expressed as a function of involute "roll distance." Normalization of the total roll-distance single-tooth contact span to unity allows tooth-meshing-harmonic amplitudes to be computed for different shapes of the above-described quantities (1) and (2). Tooth-meshing harmonics p = 1, 2, … are shown to occur at Fourier-transform harmonic values of Qp, p = 1, 2, …, where Q is the actual (total) contact ratio, thereby verifying its importance in minimizing transmission-error tooth-meshing-harmonic amplitudes. Two individual shapes and two series of shapes of the quantities (1) and (2) are chosen to illustrate a wide variety of shapes. In most cases representative of helical gears, tooth-meshing-harmonic values p = 1, 2, … are shown to occur in Fourier-transform harmonic regions governed by discontinuities arising from tooth-pair-contact initiation and termination, thereby showing the importance of minimizing such discontinuities. Plots and analytical expressions for all such Fourier transforms are presented, thereby illustrating the effects of various types of tooth-working-surface modifications and tooth-pair stiffnesses on transmission-error generation.

Social ranking effects on tooth-brushing behaviour.

PubMed

Maltby, John; Paterson, Kevin; Day, Liz; Jones, Ceri; Kinnear, Hayley; Buchanan, Heather

2016-05-01

A tooth-brushing social rank hypothesis is tested suggesting tooth-brushing duration is influenced when individuals position their behaviour in a rank when comparing their behaviour with other individuals. Study 1 used a correlation design, Study 2 used a semi-experimental design, and Study 3 used a randomized intervention design to examine the tooth-brushing social rank hypothesis in terms of self-reported attitudes, cognitions, and behaviour towards tooth-brushing duration. Study 1 surveyed participants to examine whether the perceived health benefits of tooth-brushing duration could be predicted from the ranking of each person's tooth-brushing duration. Study 2 tested whether manipulating the rank position of the tooth-brushing duration influenced participant-perceived health benefits of tooth-brushing duration. Study 3 used a longitudinal intervention method to examine whether messages relating to the rank positions of tooth-brushing durations causally influenced the self-report tooth-brushing duration. Study 1 demonstrates that perceptions of the health benefits from tooth-brushing duration are predicted by the perceptions of how that behaviour ranks in comparison to other people's behaviour. Study 2 demonstrates that the perceptions of the health benefits of tooth-brushing duration can be manipulated experimentally by changing the ranked position of a person's tooth-brushing duration. Study 3 experimentally demonstrates the possibility of increasing the length of time for which individuals clean their teeth by focusing on how they rank among their peers in terms of tooth-brushing duration. The effectiveness of interventions using social-ranking methods relative to those that emphasize comparisons made against group averages or normative guidelines are discussed. What is already known on this subject? Individual make judgements based on social rank information. Social rank information has been shown to influence positive health behaviours such as exercise. What does this study add? The health benefits of tooth-brushing are predicted by how tooth-brushing duration ranks within a distribution. Focussing on how teeth-cleaning duration ranks among others produces longer teeth-cleaning durations. © 2015 The British Psychological Society.

A numerical simulation of tooth movement by wire bending.

PubMed

Kojima, Yukio; Fukui, Hisao

2006-10-01

In orthodontic treatment, wires are bent and attached to teeth to move them via elastic recovery. To predict how a tooth will move, the initial force system produced from the wire is calculated. However, the initial force system changes as the tooth moves and may not be used to predict the final tooth position. The purpose of this study was to develop a comprehensive mechanical, 3-dimensional, numerical model for predicting tooth movement. Tooth movements produced by wire bending were simulated numerically. The teeth moved as a result of bone remodeling, which occurs in proportion to stress in the periodontal ligament. With an off-center bend, a tooth near the bending position was subjected to a large moment and tipped more noticeably than the other teeth. Also, a tooth far from the bending position moved slightly in the mesial or the distal direction. With the center V-bend, when the second molar was added as an anchor tooth, the tipping angle and the intrusion of the canine increased, and movement of the first molar was prevented. When a wire with an inverse curve of Spee was placed in the mandibular arch, the calculated tendency of vertical tooth movements was the same as the measured result. In these tooth movements, the initial force system changed as the teeth moved. Tooth movement was influenced by the size of the root surface area. Tooth movements produced by wire bending could be estimated. It was difficult to predict final tooth positions from the initial force system.

2D-RBUC for efficient parallel compression of residuals

NASA Astrophysics Data System (ADS)

Đurđević, Đorđe M.; Tartalja, Igor I.

2018-02-01

In this paper, we present a method for lossless compression of residuals with an efficient SIMD parallel decompression. The residuals originate from lossy or near lossless compression of height fields, which are commonly used to represent models of terrains. The algorithm is founded on the existing RBUC method for compression of non-uniform data sources. We have adapted the method to capture 2D spatial locality of height fields, and developed the data decompression algorithm for modern GPU architectures already present even in home computers. In combination with the point-level SIMD-parallel lossless/lossy high field compression method HFPaC, characterized by fast progressive decompression and seamlessly reconstructed surface, the newly proposed method trades off small efficiency degradation for a non negligible compression ratio (measured up to 91%) benefit.

CMT2C with vocal cord paresis associated with short stature and mutations in the TRPV4 gene

PubMed Central

Chen, D.-H.; Sul, Y.; Weiss, M.; Hillel, A.; Lipe, H.; Wolff, J.; Matsushita, M.; Raskind, W.; Bird, T.

2010-01-01

Background: Recently, mutations in the transient receptor potential cation channel, subfamily V, member 4 gene (TRPV4) have been reported in Charcot-Marie-Tooth Type 2C (CMT2C) with vocal cord paresis. Other mutations in this same gene have been described in separate families with various skeletal dysplasias. Further clarification is needed of the different phenotypes associated with this gene. Methods: We performed clinical evaluation, electrophysiology, and genetic analysis of the TRPV4 gene in 2 families with CMT2C. Results: Two multigenerational families had a motor greater than sensory axonal neuropathy associated with variable vocal cord paresis. The vocal cord paresis varied from absent to severe, requiring permanent tracheotomy in 2 subjects. One family with mild neuropathy also manifested pronounced short stature, more than 2 SD below the average height for white Americans. There was one instance of dolichocephaly. A novel S542Y mutation in the TRPV4 gene was identified in this family. The other family had a more severe, progressive, motor neuropathy with sensory loss, but less remarkable short stature and an R315W mutation in TRPV4. Third cranial nerve involvement and sleep apnea occurred in one subject in each family. Conclusion: CMT2C with axonal neuropathy, vocal cord paresis, and short stature is a unique syndrome associated with mutations in the TRPV4 gene. Mutations in TRPV4 can cause abnormalities in bone, peripheral nerve, or both and may result in highly variable orthopedic and neurologic phenotypes. GLOSSARY CMAP = compound muscle action potential; CMT = Charcot-Marie-Tooth; CMT2C = Charcot-Marie-Tooth Type 2C; HMSN = hereditary motor and sensory neuropathy; NCV = nerve conduction velocity; RFLP = restriction fragment length polymorphism; SMA = spinal muscular atrophy; SNAP = sensory nerve action potential; SPSMA = scapuloperoneal spinal muscular atrophy. PMID:21115951

The use of leucocyte and platelet-rich fibrin in socket management and ridge preservation: a split-mouth, randomized, controlled clinical trial.

PubMed

Temmerman, Andy; Vandessel, Jeroen; Castro, Ana; Jacobs, Reinhilde; Teughels, Wim; Pinto, Nelson; Quirynen, Marc

2016-11-01

To investigate the influence of the use L-PRF as a socket filling material and its ridge preservation properties. Twenty-two patients in need of single bilateral and closely symmetrical tooth extractions in the maxilla or mandible were included in a split-mouth RCT. Treatments were randomly assigned (L-PRF socket filling versus natural healing). CBCT scans were obtained after tooth extraction and three months. Scans were evaluated by superimposition using the original DICOM data. Mean ridge width differences between timepoints were measured at three levels below the crest on both the buccal and lingual sides (crest -1 mm (primary outcome variable), -3 mm and -5 mm). Mean vertical height changes at the buccal were -1.5 mm (±1.3) for control sites and 0.5 mm (±2.3) for test sites (p < 0.005). At the buccal side, control sites values were, respectively, -2.1 (±2.5), -0.3 mm (±0.3) (p < 0.005) and -0.1 mm (±0.0), and test sites values were, respectively, -0.6 mm (±2.2) (p < 0.005), -0.1 mm (±0.3) and 0.0 mm (±0.1). Significant differences (p < 0.005) were found for total width reduction between test (-22.84%) and control sites (-51.92%) at 1 mm below crest level. Significant differences were found for socket fill (visible mineralized bone) between test (94.7%) and control sites (63.3%). The use of L-PRF as a socket filling material to achieve preservation of horizontal and vertical ridge dimension at three  months after tooth extraction is beneficial. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Spectrophotometric evaluation of dental bleaching under orthodontic bracket in enamel and dentin

PubMed Central

Correr, Americo-Bortolazzo; Rastelli, Alessandra-Nara-Souza; Lima, Débora-Alves-Nunes-Leite; Consani, Rafael-Leonardo-Xediek

2014-01-01

Aware of the diffusion capacity of bleaching in the dental tissues, many orthodontists are subjecting their patients to dental bleaching during orthodontic treatment for esthetic purposes or to anticipate the exchange of esthetic restorations after the orthodontic treatment. For this purpose specific products have been developed in pre-loaded whitening trays designed to fit over and around brackets and wires, with clinical efficacy proven. Objective: The objective of this study was to evaluate, through spectrophotometric reflectance, the effectiveness of dental bleaching under orthodontic bracket. Material and Methods: Thirty-two bovine incisors crown blocks of 8 mm x 8 mm height lengths were used. Staining of tooth blocks with black tea was performed for six days. They were distributed randomly into 4 groups (1-home bleaching with bracket, 2- home bleaching without bracket, 3- office bleaching with bracket, 4 office bleaching without bracket). The color evaluation was performed (CIE L * a * b *) using color reflectance spectrophotometer. Metal brackets were bonded in groups 1 and 3. The groups 1 and 2 samples were subjected to the carbamide peroxide at 15%, 4 hours daily for 21 days. Groups 3 and 4 were subjected to 3 in-office bleaching treatment sessions, hydrogen peroxide 38%. After removal of the brackets, the second color evaluation was performed in tooth block, difference between the area under the bracket and around it, and after 7 days to verified color stability. Data analysis was performed using the paired t-test and two-way variance analysis and Tukey’s. Results: The home bleaching technique proved to be more effective compared to the office bleaching. There was a significant difference between the margin and center color values of the specimens that were subjected to bracket bonding. Conclusions: The bracket bond presence affected the effectiveness of both the home and office bleaching treatments. Key words:Tooth bleaching, spectrophotometry, orthodontics. PMID:25593650

[Dental implantation and soft tissue augmentation after ridge preservation in a molar site: a case report].

PubMed

Zhao, L P; Zhan, Y L; Hu, W J; Wang, H J; Wei, Y P; Zhen, M; Xu, T; Liu, Y S

2016-12-18

For ideal implant rehabilitation, an adequate bone volume, optical implant position, and stable and healthy soft tissue are required. The reduction of alveolar bone and changes in its morphology subsequent to tooth extraction will result in insufficient amount of bone and adversely affect the ability to optimally place dental implants in edentulous sites. Preservation of alveolar bone volume through ridge preservation has been demonstrated to reduce the vertical and horizontal contraction of the alveolar bone crest after tooth extraction and reduce the need for additional bone augmentation procedures during implant placement. In this case, a patient presented with a mandible molar of severe periodontal disease, the tooth was removed as atraumatically as possible and the graft material of Bio-Oss was loosely placed in the alveolar socket without condensation and covered with Bio-Gide to reconstruct the defects of the alveolar ridge. Six months later, there were sufficient height and width of the alveolar ridge for the dental implant, avoiding the need of additional bone augmentation and reducing the complexity and unpredictability of the implant surgery. Soft tissue defects, such as gingival and connective tissue, played crucial roles in long-term implant success. Peri-implant plastic surgery facilitated development of healthy peri-implant structure able to withstand occlusal forces and mucogingival stress. Six months after the implant surgery, the keratinized gingiva was absent in the buccal of the implant and the vestibular groove was a little shallow. The free gingival graft technique was used to solve the vestibulum oris groove supersulcus and the absence of keratinized gingiva around the implant. The deepening of vestibular groove and broadening of keratinized gingiva were conducive to the long-term health and stability of the tissue surrounding the implant. Implant installation and prosthetic restoration showed favorable outcome after six months.

High-frequency pulsed low-level diode laser therapy accelerates wound healing of tooth extraction socket: An in vivo study.

PubMed

Noda, Masahiro; Aoki, Akira; Mizutani, Koji; Lin, Taichen; Komaki, Motohiro; Shibata, Shunichi; Izumi, Yuichi

2016-12-01

This study aimed to evaluate the effects of high-frequency pulsed (HiFP) low-level laser therapy (LLLT) on early wound healing of tooth extraction sockets in rats. Bilateral maxillary first molars were extracted from 6-week-old Sprague-Dawley rats. Sockets on the right were treated by HiFP low-level diode laser irradiation (904-910 nm); the left sides served as unirradiated controls. LLLT (0.28 W, 30 kHz, 200-ns pulse, 0.6% duty cycle, 61.2 J/cm 2 total power density) was employed immediately after extraction and every 24 hours thereafter. The maxillae including the sockets were resected 3 or 7 days after extraction. Soft-tissue healing was evaluated on days 0, 3, and 7. The bone mineral content (BMC), bone volume (BV), and bone mineral density (BMD) of the extraction sockets were evaluated by microcomputed tomography, and histomorphometric analysis was carried out on day 7. Real-time PCR analysis of osteogenic marker expression and immunohistochemical detection of proliferating cell nuclear antigen (PCNA)-positive cells were performed on day 3. Compared with control sites, the un-epithelialized areas of the extracted sites were significantly reduced by irradiation (P = 0.04), and the BMC, BV, and BMD of laser-treated sites were significantly increased (P = 0.004, 0.006, and 0.009, respectively). On day 7, the mean height of newly formed immature woven bone was higher in laser-treated sites (P = 0.24). On day 3, laser-treated sites showed significantly higher osteocalcin mRNA expression (P = 0.04) and PCNA-positive cell numbers (P = 0.01). HiFP low-level diode laser irradiation enhanced soft- and hard-tissue healing of tooth extraction sockets. Lasers Surg. Med. 48:955-964, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Molecular Genetics of Supernumerary Tooth Formation

PubMed Central

Wang, Xiu-Ping; Fan, Jiabing

2011-01-01

Summary Despite advances in the knowledge of tooth morphogenesis and differentiation, relatively little is known about the aetiology and molecular mechanisms underlying supernumerary tooth formation. A small number of supernumerary teeth may be a common developmental dental anomaly, while multiple supernumerary teeth usually have a genetic component and they are sometimes thought to represent a partial third dentition in humans. Mice, which are commonly used for studying tooth development, only exhibit one dentition, with very few mouse models exhibiting supernumerary teeth similar to those in humans. Inactivation of Apc or forced activation of Wnt/β(catenin signalling results in multiple supernumerary tooth formation in both humans and in mice, but the key genes in these pathways are not very clear. Analysis of other model systems with continuous tooth replacement or secondary tooth formation, such as fish, snake, lizard, and ferret, is providing insights into the molecular and cellular mechanisms underlying succesional tooth development, and will assist in the studies on supernumerary tooth formation in humans. This information, together with the advances in stem cell biology and tissue engineering, will pave ways for the tooth regeneration and tooth bioengineering. PMID:21309064

Comminution process to produce wood particles of uniform size and shape with disrupted grain structure from veneer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooley, James H.; Lanning, David N.

Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of wood veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) aligned normal to W and L, wherein the W.times.H dimensions definemore » a pair of substantially parallel end surfaces with end checking between crosscut fibers.« less

Read/write head having a GMR sensor biased by permanent magnets located between the GMR and the pole shields

DOEpatents

Yuan, Samuel W.; Rottmayer, Robert Earl; Carey, Matthew J.

1999-01-01

A compact read/write head having a biased giant magnetoresistive sensor. Permanent magnet films are placed adjacent to the giant magnetoresistive sensor operating in the current-perpendicular-to the-plane (Cpp) mode and spaced with respect to the sensor by conducting films. These permanent magnet films provide a magnetic bias. The bias field is substantial and fairly uniform across sensor height. Biasing of the giant magnetoresistive sensor provides distinguishable response to the rising and falling edges of a recorded pulse on an adjacent recording medium, improves the linearity of the response, and helps to reduce noise. This read/write head is much simpler to fabricate and pattern and provides an enhanced uniformity of the bias field throughout the sensor.

Rotary endodontics in primary teeth – A review

PubMed Central

George, Sageena; Anandaraj, S.; Issac, Jyoti S.; John, Sheen A.; Harris, Anoop

2015-01-01

Endodontic treatment in primary teeth can be challenging and time consuming, especially during canal preparation, which is considered one of the most important steps in root canal therapy. The conventional instrumentation technique for primary teeth remains the “gold-standard” over hand instrumentation, which makes procedures much more time consuming and adversely affects both clinicians and patients. Recently nickel–titanium (Ni–Ti) rotary files have been developed for use in pediatric endodontics. Using rotary instruments for primary tooth pulpectomies is cost effective and results in fills that are consistently uniform and predictable. This article reviews the use of nickel–titanium rotary files as root canal instrumentation in primary teeth. The pulpectomy technique is described here according to different authors and the advantages and disadvantages of using rotary files are discussed. PMID:26792964

Rotary endodontics in primary teeth - A review.

PubMed

George, Sageena; Anandaraj, S; Issac, Jyoti S; John, Sheen A; Harris, Anoop

2016-01-01

Endodontic treatment in primary teeth can be challenging and time consuming, especially during canal preparation, which is considered one of the most important steps in root canal therapy. The conventional instrumentation technique for primary teeth remains the "gold-standard" over hand instrumentation, which makes procedures much more time consuming and adversely affects both clinicians and patients. Recently nickel-titanium (Ni-Ti) rotary files have been developed for use in pediatric endodontics. Using rotary instruments for primary tooth pulpectomies is cost effective and results in fills that are consistently uniform and predictable. This article reviews the use of nickel-titanium rotary files as root canal instrumentation in primary teeth. The pulpectomy technique is described here according to different authors and the advantages and disadvantages of using rotary files are discussed.

Digital Thickness Measurement of a Transparent Plastic Orthodontic Device

NASA Astrophysics Data System (ADS)

Kim, Yoon-Hwan; Rhim, Sung-Han

2018-05-01

A transparent orthodontic device is used to move the teeth to the final calibration position to form a proper set of teeth. Because the uniform thickness of the device plays an important role in tooth positioning, the accuracy of the device's thickness profile is important for effective orthodontic treatment. However, due to the complexity of the device's geometry and the transparency of the device's material, measuring the complete thickness profile has been difficult. In the present study, a new optical scanning method to measure the thickness profile of transparent plastic orthodontic devices is proposed and evaluated by using scanning electron microscopy (SEM). The error of the new measurement method is less than ±18 μm. The new method can be used to measure the thickness of non-specific, multi-curved, transparent orthodontic devices.

Propeller speed and phase sensor

NASA Technical Reports Server (NTRS)

Collopy, Paul D. (Inventor); Bennett, George W. (Inventor)

1992-01-01

A speed and phase sensor counterrotates aircraft propellers. A toothed wheel is attached to each propeller, and the teeth trigger a sensor as they pass, producing a sequence of signals. From the sequence of signals, rotational speed of each propeller is computer based on time intervals between successive signals. The speed can be computed several times during one revolution, thus giving speed information which is highly up-to-date. Given that spacing between teeth may not be uniform, the signals produced may be nonuniform in time. Error coefficients are derived to correct for nonuniformities in the resulting signals, thus allowing accurate speed to be computed despite the spacing nonuniformities. Phase can be viewed as the relative rotational position of one propeller with respect to the other, but measured at a fixed time. Phase is computed from the signals.

Development and growth of compound tooth plates in Callorhinchus milii (chondrichthyes, holocephali).

PubMed

Didier, D A; Stahl, B J; Zangerl, R

1994-10-01

The chimaeroid holocephalian fishes are distinguished among extant chondrichthyans by the possession of three pairs of tooth plates, evergrowing and partially hypermineralized, that are not shed and replaced like the teeth of living elasmobranchs. Although derivation of the chimaeroid tooth plate from the fusion of members of a plesiomorphic chondrichthyan tooth family has been proposed, evidence for this hypothesis has been lacking. A new analysis of the development and structure of the tooth plates in Callorhinchus milii (Holocephali, Chimaeriformes) reveals the compound nature of the tooth plates in a chimaeroid fish. Each tooth plate consists of an oral and aboral territory that form independently in the embryo and maintain separate growth surfaces through life. The descending lamina on the aboral surface of the tooth plate demarcates the growth surface of the aboral territory. Comparison with the tooth plates of Chimaera monstrosa indicates that compound tooth plates may be a feature of all chimaeroids in which a descending lamina is present. The tooth plates in these fishes represent the fusion of two members of a reduced tooth family. The condition of the tooth plates in C. milii is plesiomorphic for chimaeroids and is of evolutionary significance in that it provides further evidence to support a lyodont dentition in chimaeroid fishes similar to that found in other chondrichthyans. © 1994 Wiley-Liss, Inc. Copyright © 1994 Wiley-Liss, Inc.

Study of the kinematic and load sharing properties of wormgearing with non-symmetric tooth profiles

NASA Technical Reports Server (NTRS)

Sun, D. C.; Yuan, Qin

1995-01-01

The geometry of non-symmetric tooth profiles, i.e. tooth profiles with different pressure angles on the two sides of the tooth, is studied. A feasible non-symmetric tooth profile for application in helicopter transmissions is laid out as the best compromise among several conflicting factors. The non-symmetric tooth profile is then compared with the symmetric tooth profile studied previously. Based on the detailed comparisons it is concluded that the use of the non-symmetric tooth profile would severely limit the face width of the worm, consequently reduce the number of meshing teeth and cause much higher normal load on the individual gear teeth.

Fort Bragg Old Post Historic District Landscape Report

DTIC Science & Technology

2011-01-01

Low Photinia 1933 Syringa—in variety Lilacs 1933 Native Vaccinium corymbosum Highbush Blueberry 1933 Native Viburnum—in variety Viburnums ERDC...standardized planting plan for theater, chapel, and hospital (Fort Bragg Cultural Resources). ~*""’ .... "’"""nn COIOUt:..Ulltt ..c•~«O:« Io l.\\. ~· VP~N...red to blue to violet. Some Na- tive Vaccinium corymbo- sum Highbush Blueberry Height: 6-12 ft Rounded, multi- stemmed, fairly uniform, arching

Discoloration Potential of Endodontic Sealers: A Brief Review

PubMed Central

Tour Savadkouhi, Sohrab; Fazlyab, Mahta

2016-01-01

Tooth discoloration induced by endodontic sealers, is a common finding that impairs aesthetic outcome of endodontic treatment. The aim of the present mini literature review, was to summarize the existing data on discoloration potential of different endodontic sealers. The research covered the article published in PubMed and Google Scholar from 2000 to 2015. The searched keywords included ‘tooth discoloration AND endodontic’, ‘tooth discoloration AND sealer, ‘tooth discoloration AND zinc-oxide eugenol sealer’, ‘tooth discoloration AND Calcium Hydroxide Sealer’, ‘tooth discoloration AND Glass Ionomer Sealer’, ‘tooth discoloration AND epoxy-resin Sealer’, ‘tooth discoloration AND Silicon Based Sealer’, ‘tooth discoloration AND Bioceramic Sealer’ and ‘Spectrophotometry’. Conclusion: A total number of 44 articles were gained which reduced to 11 after excluding the repetitive items. The available evidence for discoloration potential of endodontic sealers currently available on the market is scarce. However, it can be concluded that all endodontic sealers can potentially stain the tooth structure to different degrees. PMID:27790251

Influence of occlusal contact area on cusp defection and stress distribution.

PubMed

Costa, Anna Karina Figueiredo; Xavier, Thaty Aparecida; Paes-Junior, Tarcisio José Arruda; Andreatta-Filho, Oswaldo Daniel; Borges, Alexandre Luiz Souto

2014-11-01

The purpose of this study was to evaluate the effect of occlusal contact area for loading on the cuspal defection and stress distribution in a first premolar restored with a high elastic modulus restorative material. The Rhinoceros 4.0 software was used for modeling the three-dimensional geometries of dental and periodontal structures and the inlay restoration. Thus, two different models, intact and restored teeth with three occlusal contact areas, 0.1, 0.5 and 0.75 mm(2), on enamel at the occlusal surface of buccal and lingual cusps. Finite element analysis (FEA) was performed with the program ANSYS (Workbench 13.0), which generated a mesh with tetrahedral elements with greater refinement in the regions of interest, and was constrained at the bases of cortical and trabecular bone in all axis and loaded with 100 N normal to each contact area. To analysis of maximum principal stress, the smaller occlusal contact area showed greater compressive stress in region of load application for both the intact and inlay restored tooth. However, tensile stresses at the occlusal isthmus were similar for all three tested occlusal contact areas (60 MPa). To displacement of the cusps was higher for teeth with inlay (0.46-0.48 mm). For intact teeth, the smaller contact area showed greater displacement (0.10 mm). For teeth with inlays, the displacement of the cusps were similar in all types of occlusal area. Cuspal displacement was higher in the restored tooth when compared to the intact tooth, but there were no significant variations even with changes in the occlusal contact area. RELEVANCE CLINICAL: Occlusal contacts have a great influence on the positioning of teeth being able to maintain the position and stability of the mandible. Axial loads would be able to generate more uniform stress at the root presenting a greater concentration of load application in the point and the occlusal surface. Thus, is necessary to analyze the relationship between these occlusal contacts as dental wear and subsequent occlusal interferences.

Tooth colour change with Ozicure Oxygen Activator: a comparative in vitro tooth bleaching study.

PubMed

Grundlingh, A A; Grossman, E S; Witcomb, M J

2012-08-01

This in vitro study compared a new tooth bleaching product, Ozicure Oxygen Activator (O3, RSA) with Opalescence Quick (Ultradent, USA) using a randomised block design to assess tooth colour change. Colour change, stability and relapse in canine, incisor and premolar teeth was assessed following three bleach treatments and subsequent tooth colour assessment. Ninety nine teeth (canines, incisors and premolars), which were caries free, had no surface defects and were within the colour range 1M2 and 5M3 were selected. Teeth were randomly divided into the three experimental groups: Opalescence Quick, Ozicure Oxygen Activator and control. The three experimental groups received three treatments of one hour each over three consecutive days. Tooth colour was assessed using the Vitapan 3D Master Tooth Guide (VITA, Germany). A General Linear Models test for analysis of variance for a fractional design with significance set at P < 0.05 was used to test for significance. Both bleaching methods significantly lightened the teeth (P < 0.0001). Tooth colour change was mainly after the first hour of tooth bleaching. The tooth type was significant in tooth colour change (P = 0.0416). Tooth colour relapse and resistance to colour change were observed. Ozicure Oxygen Activator bleached teeth in a manner and to an extent similar to Opalescence Quick.

Inhibitory effect of interferon-γ on experimental tooth movement in mice.

PubMed

Kohara, Haruka; Kitaura, Hideki; Yoshimatsu, Masako; Fujimura, Yuji; Morita, Yukiko; Eguchi, Toshiko; Yoshida, Noriaki

2012-09-01

The aim of this study was to investigate the effects of interferon (IFN)-γ on experimental tooth movement in mice using a murine experimental tooth movement model. An Ni-Ti closed-coil spring was inserted between the upper-anterior alveolar bones and the upper-left first molars in mice. We evaluated the relationship between local Ifn-γ mRNA levels and orthodontic tooth movement. In other experiments, IFN-γ was injected adjacent to each first molar every other day during tooth movement. After 12 days, the amount of tooth movement was measured. Tartrate-resistant acid phosphatase (TRAP)-positive cells at the pressure side of each experimental tooth were counted as osteoclasts. Local Ifn-γ mRNA expression increased with orthodontic tooth movement. The number of TRAP-positive cells increased on the pressure side of the first molar. In contrast, the degree of tooth movement and the number of TRAP-positive cells on the pressure side in IFN-γ-injected mice were less than those of control mice. IFN-γ was induced in experimental tooth movement, and could inhibit mechanical force-loaded osteoclastogenesis and tooth movement. These results suggest that IFN-γ might be useful in controlling orthodontic tooth movement because of its inhibitory action on excessive osteoclastogenesis during this movement.

Occlusal tooth wear in the general population of Germany: effects of age, sex, and location of teeth.

PubMed

Schierz, Oliver; Dommel, Sandra; Hirsch, Christian; Reissmann, Daniel R

2014-09-01

Tooth wear is an increasing problem in a society where people are living longer. The purpose of this study was to assess the effect of age, sex, and location of teeth on the severity of tooth wear and to determine the prevalence of dentin exposure in the general population of Germany. Tooth wear was measured in casts of both jaws of 836 persons with a 6-point (0-5) ordinal rating scale. Linear random-intercept regression models with the covariates of age, sex, jaw, and tooth group (with the participant as a grouping variable) were computed to determine the association of these covariates with tooth wear of a single tooth. The mean tooth wear score across all age groups, both sexes, and all teeth was 2.9 (standard deviation, 0.8), and the prevalence of teeth with exposed dentin was 23.4%. The participants' age was correlated with the mean tooth wear scores (r=0.51). The tooth wear level among women was on average 0.15 units lower than among men, and tooth wear was on average 0.59 units higher for anterior teeth than for posterior teeth. Increased tooth wear in anterior teeth may be due to the initially predominant guidance by anterior teeth, with age-related linear progress in tooth wear. Occlusal tooth wear scores and dentin exposure increase with age. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Tooth bleaching and young adults in Nigeria: knowledge, experiences and intention.

PubMed

Azodo, C C; Ogbomo, A C; Agbor, M A

2012-12-01

To assess the knowledge, experiences and intention to have tooth bleaching among young adults studying in a Nigerian University. A cross-section of part-time undergraduate students of University of Benin, Benin City, Nigeria were studied in 2010 using a self-administered questionnaire. About three-quarters 289 (72.4%) of the respondents reported awareness of at least one cause of tooth discoloration. A total of 143 (35.8%) of the respondents have heard of tooth bleaching with main sources of information being friends/relatives, dentists and the internet. One-third 132 (33.1%) of the respondents correctly identified that the aim of tooth bleaching was to make the teeth whiter. The respondents that had correct knowledge about mechanism, duration and complications of tooth bleaching were 51 (12.8%), 25 (6.3%) and 35 (8.8%) respectively. The major perceived benefits of tooth bleaching reported by the respondents were self confidence boost 152 (38.1%) and improvement of one's beauty 107 (26.8%). Out of the 68 (17.0%) respondents that have attempted tooth bleaching, 36 (52.9%) used tooth whitening toothpaste. Out of the 151 (37.8%) respondents that expressed intention of having tooth bleaching procedure, 32 (21.2%) would pursue the course, no matter the cost. In the studied population, knowledge of tooth discoloration was high, awareness and experiences of tooth bleaching were low but significant number expressed intention of having tooth bleaching. It is important that dentists increase oral health information particularly tooth bleaching information accessibility to the young adult population to improve the knowledge and prevent adverse effects.

Height and relative leg length as indicators of the quality of the environment among Mozambican juveniles and adolescents.

PubMed

Padez, Cristina; Varela-Silva, Maria Inês; Bogin, Barry

2009-01-01

The growth status of Mozambique adolescents was assessed to test the hypothesis that relative leg length is a more sensitive indicator of the quality of the environment than the total height. The sample comprised 690 boys and 727 girls, aged between 9 and 17 years, from Maputo. It is divided between those living in the Centre of Maputo and those living in the slums on the periphery of the city. Height, weight, and sitting height were measured and the sitting height ratio was calculated. The hypothesis that relative leg length is more sensitive than total stature as an indicator of environmental quality is not uniformly confirmed. Overall, mean stature is greater for the centre group than the slum group, but relative leg length as measured by the sitting height ratio does not differ. Compared with African-American references (NHANES II), all centre girls, 9- to 14-year-old slum girls, all slum boys, and the oldest centre boys show relatively shorter legs. These findings show that within the Mozambique sample, relative leg length is not sensitive enough to distinguish the quality of the living environment. Mozambique was a colony of Portugal until 1975. Civil unrest and warfare characterized the late Colonial period and the postindependence period until a peace settlement was concluded in 1992. It is possible that all socioeconomic status groups within the country suffered sufficiently to reduce relative leg length compared with the better-off African-American reference sample. Possible genetic influences on relative leg length are also discussed.

Tooth quality in dental fluorosis genetic and environmental factors.

PubMed

Vieira, A P G F; Hanocock, R; Eggertsson, H; Everett, E T; Grynpas, M D

2005-01-01

Dental fluorosis (DF) affects the appearance and structure of tooth enamel and can occur following ingestion of excess fluoride during critical periods of amelogenesis. This tooth malformation may, depending on its severity, influence enamel and dentin microhardness and dentin mineralization. Poor correlation between tooth fluoride (F) concentration and DF severity was shown in some studies, but even when a correlation was present, tooth fluoride concentration explained very little of DF severity. This fact calls into question the generally accepted hypothesis that the main factor responsible for DF severity is tooth fluoride concentration. It has been shown previously that genetic factors (susceptibility to DF) play an important role in DF severity although DF severity relates to individual susceptibility to fluoride exposure (genetics), tooth fluoride concentration relates to fluoride ingestion (environmental). The objective of this study was to investigate the correlation between tooth fluoride concentration, DF severity, and tooth mechanical and materials properties. Three strains of mice (previously shown to have different susceptibility to DF) at weaning were treated with four different levels of F in their water (0, 25, 50, and 100 ppm) for 6 weeks. Mice teeth were tested for fluoride by instrumental neutron activation analysis (INAA), DF severity determined by quantitative light-induced fluorescence [QLF], and tooth quality (enamel and dentin microhardness and dentin mineralization). Tooth fluoride concentration (environment factor) correlated positively with DF severity (QLF) (rs=0.608), fluoride treatment group (rs=0.952). However, tooth fluoride concentration correlated negatively with enamel microhardness (rs=-0.587), dentin microhardness (rs=-0.268) and dentin mineralization (rs=-0.245). Dental fluorosis (genetic factor) severity (QLF) correlated positively with fluoride treatment (rs=0.608) and tooth fluoride concentration (rs=0.583). DF severity correlated negatively with enamel microhardness (rs=-0.564) and dentin microhardness (rs=-0.356). Genetic factors (DF severity) and the environmental factor (fluoride concentration in tooth structure) have similar influence on tooth biomechanical properties, whereas only the environmental factor has an influence on tooth material property (mineralization).

Tooth - abnormal shape

MedlinePlus

Hutchinson incisors; Abnormal tooth shape; Peg teeth; Mulberry teeth; Conical teeth ... The appearance of normal teeth varies, especially the molars. ... conditions. Specific diseases can affect tooth shape, tooth ...

Analysis of the golden proportion and width/height ratios of maxillary anterior teeth in Arab and Kurdish populations.

PubMed

Al-Kaisy, Neda; Garib, Balkees Taha

2017-11-15

Dentists providing anterior restorations are guided by the principles of anatomic tooth dimension. Dental biometrics should consider ethnicity to produce a more comprehensive evaluation. The purpose of this clinical study was to analyze the anatomic crowns of maxillary central incisors (CI), lateral incisors (LI), and canines (C) with respect to the golden proportion (GP) and width/height (W/H) ratio in Kurdish and Arab populations. Maxillary gypsum casts were obtained from 100 participants (50 from a Kurdish and 50 from an Arab population). Standardized digital photographs of each cast were recorded. The apparent and actual anterior tooth dimensions were determined by ImageJ software for the calculation of the GP and W/H ratio. Data were statistically analyzed using ANOVA to investigate ethnic, sex, and arch side differences. The chi-square test was used to explore the GP, and the 1-sample t test was used to test the ideal W/H ratio (α=.05). The GP was found in both the Kurdish and Arab groups in the LI/CI mean (0.62, 0.63), but not in the C/LI mean (0.69, 0.73). No difference due to sex was detected in the LI/CI in either ethnic group, but Kurdish men had significantly larger C/LI than women (0.73, 0.66, P=.006) and larger right-side LI/CI than left (0.63, 0.60, P=.049). The W/H ratio was higher than the predicted ideal ratio of 80% (range, 88% to 90%). The LI W/H ratio in Arabs was significantly larger than in Kurds (90.3% versus 82.7%, respectively; P<.001). The GP was found to exist between the apparent widths of maxillary anterior teeth LI/CI for the both populations in both men and women but not for C/LI. No ideal ratio was detected for the W/H ratios. Specific population characteristics must be taken into consideration, especially when applying the proportions to Kurdish individuals. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Prevalence of Tooth Shade and its Correlation with Skin Colour - A Cross-sectional Study.

PubMed

Vadavadagi, Suneel V; Kumari, K V Halini; Choudhury, Gopal Krishna; Vilekar, Abhishek Madhukar; Das, Sitansu Sekhar; Jena, Debkant; Kataraki, Bharat; B L, Bhavana

2016-02-01

Aesthetics has become an important issue in modern society. Tooth shade is one of the factors in determining aesthetics. Studies have revealed that tooth shade is influenced by age, gender, eye colour, skin colour and other factors. The present study was aimed to assess the prevalence of tooth shade and its correlation with skin colour. A total of 300 subjects aged 18-20 years were evaluated for tooth shade using Vitapan - 3D shade guide. Anterior teeth were checked under natural light and facial skin colour by Lakme liquid foundation make up as a shade guide. Data was analysed using chi square test and spearman's correlation. Out of 300 students, 114 (38.00%) had A2 tooth shade; the least prevalent tooth shade among Chitradurga population was C1 (4.00%). There was a positive correlation between tooth shade and skin colour which was found to be statistically significant (p <0.05). The most prevalent tooth shade among Chitradurga population was A2 and least was C1. There was a significant correlation between tooth shade and skin colour with lighter skin tone subjects having lighter tooth shade hence skin colour can be used as a guide for shade selection.

Application of tooth brushing behavior to active rest.

PubMed

Sadachi, Hidetoshi; Murakami, Yoshinori; Tonomura, Manabu; Yada, Yukihiro; Simoyama, Ichiro

2010-01-01

We evaluated the usefulness of tooth brushing with toothpaste as active rest using the flicker value as a physiological parameter and a subjective questionnaire as a psychological parameter. Seventeen healthy, right-handed subjects (12 males and 5 females) aged 22.5 +/- 1.5 yr (mean +/- standard deviation) were randomly divided into tooth brushing with toothpaste (N=9) and non-tooth brushing groups (N=8). The subjects performed a serial calculation task for 20 min using personal computers. Subsequently, the tooth brushing group brushed their teeth, and the flicker value and mood were compared before and after the tooth brushing. The flicker value significantly increased in the tooth brushing group compared with the non-tooth brushing group (p<0.05). Concerning the mood, in the tooth brushing group, the incidence of a "feeling of being refreshed" significantly increased (p<0.05), that of "concentration power" or a "feeling of clear-headedness" tended to increase (p<0.1), and that of "lassitude" or "sleepiness" significantly decreased (p<0.01). Somatosensory stimulation and intraoral tactile stimulation during tooth brushing activated cerebral activity, producing refreshing effects. These results suggest the applicability of tooth brushing to active rest.

Cold-Water Immersion for Hyperthermic Humans Wearing American Football Uniforms.

PubMed

Miller, Kevin C; Swartz, Erik E; Long, Blaine C

2015-08-01

Current treatment recommendations for American football players with exertional heatstroke are to remove clothing and equipment and immerse the body in cold water. It is unknown if wearing a full American football uniform during cold-water immersion (CWI) impairs rectal temperature (Trec) cooling or exacerbates hypothermic afterdrop. To determine the time to cool Trec from 39.5°C to 38.0°C while participants wore a full American football uniform or control uniform during CWI and to determine the uniform's effect on Trec recovery postimmersion. Crossover study. Laboratory. A total of 18 hydrated, physically active, unacclimated men (age = 22 ± 3 years, height = 178.8 ± 6.8 cm, mass = 82.3 ± 12.6 kg, body fat = 13% ± 4%, body surface area = 2.0 ± 0.2 m(2)). Participants wore the control uniform (undergarments, shorts, crew socks, tennis shoes) or full uniform (control plus T-shirt; tennis shoes; jersey; game pants; padding over knees, thighs, and tailbone; helmet; and shoulder pads). They exercised (temperature approximately 40°C, relative humidity approximately 35%) until Trec reached 39.5°C. They removed their T-shirts and shoes and were then immersed in water (approximately 10°C) while wearing each uniform configuration; time to cool Trec to 38.0°C (in minutes) was recorded. We measured Trec (°C) every 5 minutes for 30 minutes after immersion. Time to cool from 39.5°C to 38.0°C and Trec. The Trec cooled to 38.0°C in 6.19 ± 2.02 minutes in full uniform and 8.49 ± 4.78 minutes in control uniform (t17 = -2.1, P = .03; effect size = 0.48) corresponding to cooling rates of 0.28°C·min(-1) ± 0.12°C·min(-1) in full uniform and 0.23°C·min(-1) ± 0.11°C·min(-1) in control uniform (t17 = 1.6, P = .07, effect size = 0.44). The Trec postimmersion recovery did not differ between conditions over time (F1,17 = 0.6, P = .59). We speculate that higher skin temperatures before CWI, less shivering, and greater conductive cooling explained the faster cooling in full uniform. Cooling rates were considered ideal when the full uniform was worn during CWI, and wearing the full uniform did not cause a greater postimmersion hypothermic afterdrop. Clinicians may immerse football athletes with hyperthermia wearing a full uniform without concern for negatively affecting body-core cooling.

[Assessment of tooth bleaching efficacy with spectrophotometer].

PubMed

Zhu, Wenhao; Liu, Chang; Pan, Jie

2014-06-01

To analyze the changes in CIE L*, a*, and b* at cervical, body, and incisal sites after tooth bleaching by using a spectrophotometer. Sixty-seven intact and healthy maxillary central incisors were in-vestigated. These incisors were darker than A3 according to the Vita Classical shade guide. The CIE tooth shade parameters L*, a*, and b* were simultaneously recorded at three tooth areas (cervical, body, and incisal) with a spectrophotometer before and after tooth bleaching (35%H2O2 coordinating with Beyond whitening accelerator irradiating). The shade dif-ferential (DeltaE) was calculated. ANOVA, paired t-test, and Pearson correlation analysis were used for data analysis. The efficacy rates of tooth bleaching were satisfactory, with 86.6%, 86.6%, and 85.1% in the cervical, body, and incisal sites, respectively. The average values of DeltaE were 5.09, 4.44, and 4.40 in the cervical, body, and incisal sites. Tooth bleaching significantly increased L* and significantly decreased a* and b* in all tooth areas (P < 0.01). The decreasing range of Deltab* was more than the increasing range of DeltaL* at the cervical site; opposite results were observed at the incisal site. A positive correlation was detected between baseline b* and DeltaE. The spectrophotometer could objectively evaluate the whitening effect of tooth bleaching at the different tooth sites. The tooth bleaching system (35%H202 coordinating with Beyond whitening accelerator irradiating) exerts powerful bleaching actions in most of the tooth areas investigated. The order of tooth bleaching effectiveness is cervicalbody>incisal. Yellow coloration is decreased mainly at the cervical site, and brightness was increased mostly at theincisal site. The effectiveness of tooth bleaching increases as the baseline b* value increases.

Distinct developmental genetic mechanisms underlie convergently evolved tooth gain in sticklebacks

PubMed Central

Ellis, Nicholas A.; Glazer, Andrew M.; Donde, Nikunj N.; Cleves, Phillip A.; Agoglia, Rachel M.; Miller, Craig T.

2015-01-01

Teeth are a classic model system of organogenesis, as repeated and reciprocal epithelial and mesenchymal interactions pattern placode formation and outgrowth. Less is known about the developmental and genetic bases of tooth formation and replacement in polyphyodonts, which are vertebrates with continual tooth replacement. Here, we leverage natural variation in the threespine stickleback fish Gasterosteus aculeatus to investigate the genetic basis of tooth development and replacement. We find that two derived freshwater stickleback populations have both convergently evolved more ventral pharyngeal teeth through heritable genetic changes. In both populations, evolved tooth gain manifests late in development. Using pulse-chase vital dye labeling to mark newly forming teeth in adult fish, we find that both high-toothed freshwater populations have accelerated tooth replacement rates relative to low-toothed ancestral marine fish. Despite the similar evolved phenotype of more teeth and an accelerated adult replacement rate, the timing of tooth number divergence and the spatial patterns of newly formed adult teeth are different in the two populations, suggesting distinct developmental mechanisms. Using genome-wide linkage mapping in marine-freshwater F2 genetic crosses, we find that the genetic basis of evolved tooth gain in the two freshwater populations is largely distinct. Together, our results support a model whereby increased tooth number and an accelerated tooth replacement rate have evolved convergently in two independently derived freshwater stickleback populations using largely distinct developmental and genetic mechanisms. PMID:26062935

Factors associated with tooth loss and prosthodontic status among Sudanese adults.

PubMed

Khalifa, Nadia; Allen, Patrick F; Abu-bakr, Neamat H; Abdel-Rahman, Manar E

2012-01-01

A study was conducted to determine the degree of tooth loss, factors influencing tooth loss, and the extent of prosthodontic rehabilitation in Sudanese adults (≥ 16 years old) attending outpatient clinics in Khartoum State. Pearson and multivariate analyses were used to examine the relationships between tooth loss and specific characteristics determined through interviews and clinical examinations. The mean number of missing teeth was 3.6 (SD, 4.9) and the prevalence of edentulism was 0.1%. The prevalence of tooth loss (missing at least one tooth) was 78%; 66.9% of tooth loss was due to caries, and 11.2% was attributable to other reasons. Prosthetic replacement of missing teeth was evident in 3%, whereas a need for prosthetic replacement was evident in 57%. Having < 20 teeth was associated with age, gender, and socioeconomic status; tooth loss due to caries was associated with age, tribe, frequency of tooth-brushing, and a low rate of dental consultation. Tooth loss due to other reasons was associated with age, tribe, education, periodontal pocketing, tobacco use, tooth wear, and prosthetic status. The results of the present study indicated that the major cause of tooth loss was dental caries, thus emphasizing the importance of a public prevention-based healthcare program. Replacement of missing teeth was uncommon in the study subjects, which may reflect lack of access to this type of oral healthcare.

Clinical and biometrical evaluation of socket preservation using demineralized freeze-dried bone allograft with and without the palatal connective tissue as a biologic membrane.

PubMed

Moghaddas, Hamid; Amjadi, Mohammad Reza; Naghsh, Narges

2012-11-01

Alveolar ridge preservation following tooth extraction has the ability to maintain the ridge dimensions and allow the implant placement in an ideal position fulfilling both functional and aesthetic results. The aim of this study was to evaluate the efficacy of the palatal connective tissue as a biological membrane for socket preservation with demineralized freeze-dried bone allograft (DFDBA). Twelve extraction sites were treated with DFDBA with (case group) and without (control group) using autogenous palatal connective tissue membrane before placement of implants. Alveolar width and height, amount of keratinized tissue, and gingival level were measured at pre-determined points using a surgical stent at two times, the time of socket preservation surgery. In both groups a decrease in all socket dimensions was found. The average decrease in socket width, height, keratinized tissue, and gingival level in case group was 1.16, 0.72, 3.58, and 1.27 mm, and in control group was 2.08, 0.86, 4.52, and 1.58 mm respectively. Statistical analysis showed that decrease in socket width (P = 0.012), keratinized tissue (P ≤ 0.001), and gingival level (P = 0.031) in case group was significantly lower than that of the control group. Results showed no meaningful difference in socket height changes when compared with case and control groups (P = 0.148). Under the limits of this study, connective tissue membrane could preserve socket width, amount of keratinized tissue, and the gingival level more effectively than DFDBA alone.

Do gingival soft tissues benefit from the application of a papilla preservation flap technique in endodontic surgery?

PubMed

Taschieri, Silvio; Corbella, Stefano; Del Fabbro, Massimo

2014-10-01

A healthy gingival condition after endodontic surgery may depend on adequate soft tissue management. The aim of this study was to compare 2 incision techniques, papilla base incision (PBI) and intrasulcular flap (IS), which are currently used in endodontic surgery. In the present nonrandomized controlled clinical trial, patients requiring endodontic surgery on a single tooth were enrolled. PBI was used in 1 group and IS was used in the other group. The primary outcomes were changes in periodontal probing depth, gingival recession, and height of the interproximal mesial and distal papillae. Outcome variables were assessed preoperatively and 6 months after surgery. Between-group differences were evaluated through appropriate statistical analysis, with significance set at a P value equal to .05. Each group was composed of 12 patients and the 2 groups were comparable at baseline. Two weeks after surgery, papilla height decreased significantly in the IS group (2.05 and 1.80 mm at the mesial and distal aspects, respectively), whereas no significant decrease in papilla height was observed in the PBI group (0.10 and 0.20 mm). No statistically significant difference between groups was observed after 6 months. No significant difference between groups was found for gingival recession or probing depth at any follow-up time. Better soft tissue preservation in the early postoperative period was achieved using the PBI approach compared with the IS approach. The PBI can be recommended for endodontic surgical procedures involving esthetic regions. Copyright © 2014 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Roost habitat of Mexican Spotted Owls (Strix occidentalis lucida) in the canyonlands of Utah

USGS Publications Warehouse

Willey, David W.; van Riper, Charles

2015-01-01

In large portions of their geographic range, Mexican Spotted Owls (Strix occidentalis lucida) roost in forest-dominated environments, but in some areas the owls use relatively arid rocky canyonlands. We measured habitat characteristics at 133 male roosts (n = 20 males) during 1992-95, and 56 female roosts (n = 13 females) during 1994-95. Across all years and study areas, 44% of Mexican Spotted Owl roosts occurred in mixed-conifer forest patches, 30% in desert scrub habitat, 16% in pinyon-juniper woodlands, and 10% of roosts occurred in riparian vegetation. Two basic substrates were used as perches by owls, including rock ledges or various trees, where roost height averaged 9 m (0.54 SD), and average height of cliffs above perched owls was 50 m (58 SD). For both males and females, trees types used most frequently included various firs (51%), followed by pinyon pine (18%), Utah juniper (15%), and big-tooth maple or box elder combined (15%). Roost sites were located in canyons composed of cliff-forming geologic formations, primarily oriented north-west to south-east. The width of canyons measured at roosts averaged 68 m (105 SD), but ranged from 1-500 m. Canopy cover at roosts used by owls ranged from 44% to 71%, mean tree height of all trees present was 9.5 m and mean diameter of trees was 25.4 cm. Non-roost habitat was warmer, not as steep, and possessed fewer caves and ledges than roost habitat. Trees present in roost plots were taller, and thus showed greater average diameter than trees present in non-roost habitat.

Influence of tooth profile on the noncircular gear tooth contact

NASA Astrophysics Data System (ADS)

Cristescu, A.; Andrei, L.; Cristescu, B.

2017-02-01

With noncircular gears, the continuous modification of the tooth meshing, in terms of variation of the tooth profiles and the line of action position and inclination, makes difficult the implementation of a general standard procedure for the analysis of the noncircular gears tooth contact. In this paper, the authors present a graphical approach that enables the tooth contact static pattern to be produced and evaluated in case of a noncircular gear with complex geometry of the pitch curve. The study is virtually developed, in AutoCAD environment, by animating and investigating the gear solid models in mesh. The tooth static contact analysis enables the path of contact area and distribution to be evaluated in correlation with the following variable initial data: gear pitch curve geometry, tooth profile geometry, as a consequence of different generating procedures, and the gear pressure angle. It was found out that the noncircular gear tooth contact could be improved by choosing different procedures for the tooth flank generation in concave and convex zones and by increasing the gear pressure angle.

The prevalence, aetiology and clinical appearance of tooth wear: the Nigerian experience.

PubMed

Oginni, O; Olusile, A O

2002-08-01

To establish the prevalence and severity of tooth wear among Nigerians and to compare the pattern and aetiology with findings of earlier studies in Western populations. Clinical examinations for tooth wear using the tooth wear index (TWI). The Federal Republic of Nigeria. Patients attending the Dental Hospital, Obafemi Awolowo University Teaching Hospital's Complex Ile-Ife. Attrition, abrasion and erosion. Of the 126 patients with tooth wear 81 had attrition, 20 had abrasion, 9 had erosion and 16 had attrition and abrasion combined. A total of 15,480 tooth surfaces were examined. 2,229 (14.4%) surfaces had tooth wear out of which 1,007 (6.5%) were pathologically worn down. The frequency of tooth wear increased with the age of patients. Most of the pathologically worn surfaces were just one point above maximum acceptable value. The aetiological factors associated with tooth wear are not different from those encountered in Western cultures but the pattern of wear differs. Pathological tooth wear presents as an age related phenomenon and is probably more severe in Nigerians.

Strategy of restraining ripple error on surface for optical fabrication.

PubMed

Wang, Tan; Cheng, Haobo; Feng, Yunpeng; Tam, Honyuen

2014-09-10

The influence from the ripple error to the high imaging quality is effectively reduced by restraining the ripple height. A method based on the process parameters and the surface error distribution is designed to suppress the ripple height in this paper. The generating mechanism of the ripple error is analyzed by polishing theory with uniform removal character. The relation between the processing parameters (removal functions, pitch of path, and dwell time) and the ripple error is discussed through simulations. With these, the strategy for diminishing the error is presented. A final process is designed and demonstrated on K9 work-pieces using the optimizing strategy with magnetorheological jet polishing. The form error on the surface is decreased from 0.216λ PV (λ=632.8  nm) and 0.039λ RMS to 0.03λ PV and 0.004λ RMS. And the ripple error is restrained well at the same time, because the ripple height is less than 6 nm on the final surface. Results indicate that these strategies are suitable for high-precision optical manufacturing.

Ameloglyphics: A possible forensic tool for person identification following high temperature and acid exposure

PubMed Central

Juneja, Manjushree; Juneja, Saurabh; Rakesh, Nagaraju; Bhoomareddy Kantharaj, Yashoda Devi

2016-01-01

Introduction: Forensic odontology is a branch that is evolving over time and has opened newer avenues that may help in the identification of individuals. Tooth prints are the enamel rod end patterns on tooth surface and they are considered as a hard tissue analog to fingerprints. Teeth have the highest resistance to most environmental effects like fire, desiccation, and decomposition, and may be used as a forensic evidence. Aims and Objectives: The aim of the study was to evaluate if the tooth prints could be used for an individual's identification and reproducibility and permanency of these tooth prints after exposing the teeth to acid and various degrees of temperature. Materials and Methods: 90 tooth prints from 20 freshly extracted maxillary premolar teeth were obtained. Cellophane tape technique was used to record enamel rod end patterns on tooth surface. Ten teeth (one from each patient) were immersed in 36.46% hydrochloric acid and the tooth prints were obtained at various intervals (5 min, 10 min, and 20 min). The other 10 teeth (one from each patient) were incinerated and impression was made at various intervals (80° C, 400° C, 600° C, and 750° C). Tooth prints obtained from different teeth (total of 90 tooth prints) were analyzed using Verifinger® standard SDK version 5.0 software. Results: All the 20 original tooth prints were distinct from each other and no inter-individual or intra-individual similarity was found. The tooth prints from the same tooth after it was exposed to acid or heat were reproducible and showed high to very high similarity with the original tooth print of that particular tooth stored in the database. Conclusion: Tooth prints may be used as an effective aid in person identification even in adverse conditions such as burn and acid attack injuries. PMID:27051220

Associations between smoking and tooth loss according to reason for tooth loss

PubMed Central

Mai, Xiaodan; Wactawski-Wende, Jean; Hovey, Kathleen M.; LaMonte, Michael J.; Chen, Chaoru; Tezal, Mine; Genco, Robert J.

2013-01-01

Background Smoking is associated with tooth loss. However, smoking's relationship to the specific reason for tooth loss in postmenopausal women is unknown. Methods Postmenopausal women (n = 1,106) who joined a Women's Health Initiative ancillary study (The Buffalo OsteoPerio Study) underwent oral examinations for assessment of the number of missing teeth, as well as the self-reported reasons for tooth loss. The authors obtained information about smoking status via a self-administered questionnaire. The authors calculated odds ratios (ORs) and 95 percent confidence intervals (CIs) by means of logistic regression to assess smoking's association with overall tooth loss, as well as with tooth loss due to periodontal disease (PD) and with tooth loss due to caries. Results After adjusting for age, education, income, body mass index (BMI), history of diabetes diagnosis, calcium supplement use and dental visit frequency, the authors found that heavy smokers (≥ 26 pack-years) were significantly more likely to report having experienced tooth loss compared with never smokers (OR = 1.82; 95 percent CI, 1.10-3.00). Smoking status, packs smoked per day, years of smoking, pack-years and years since quitting smoking were significantly associated with tooth loss due to PD. For pack-years, the association for heavy smokers compared with that for never smokers was OR = 6.83 (95 percent CI, 3.40-13.72). The study results showed no significant associations between smoking and tooth loss due to caries. Conclusions and Practical Implications Smoking may be a major factor in tooth loss due to PD. However, smoking appears to be a less important factor in tooth loss due to caries. Further study is needed to explore the etiologies by which smoking is associated with different types of tooth loss. Dentists should counsel their patients about the impact of smoking on oral health, including the risk of tooth loss due to PD. PMID:23449901

A new design of indirectly heated cathode based strip type electron gun.

PubMed

Maiti, Namita; Lijeesh, K; Barve, U D; Quadri, Nishad; Tembhare, G U; Mukherjee, S; Thakur, K B; Das, A K

2013-08-01

A new design of indirectly heated solid cathode based electron gun (200 kW, 45 kV, 270° bent strip type electron gun) has been presented. The design issue addressed is the uniformity of temperature on the solid cathode using (a) a multi-segmented filament with variable height as the primary heat source and (b) trapezoidal shaped single long filament as the primary heat source. The proposed design in this paper is based on computer simulation and validated by extensive experimentations. The design emphasis is on maintaining uniform temperature on the solid cathode. The designed multi-segment filament and the single long filament provide a temperature uniformity on the solid cathode of about 250 K and 110 K, respectively. The better temperature uniformity inspite of the thermal expansion, in case of a single long filament tightly clamped at two ends, has been possible due to shaping of the single filament with a number of constituent sections such that the thermal expansion of different sections forming the actual filament takes care of not only the mechanical stability but also does not affect the emitting surface of the filament. Experiments show that the modified design achieves a one to one correspondence of the solid cathode length and the electron beam length emitted from the solid cathode.

Tooth fracture risk analysis based on a new finite element dental structure models using micro-CT data.

PubMed

Chen, G; Fan, W; Mishra, S; El-Atem, A; Schuetz, M A; Xiao, Y

2012-10-01

The finite element (FE) analysis is an effective method to study the strength and predict the fracture risk of endodontically-treated teeth. This paper presents a rapid method developed to generate a comprehensive tooth FE model using data retrieved from micro-computed tomography (μCT). With this method, the inhomogeneity of material properties of teeth was included into the model without dividing the tooth model into different regions. The material properties of the tooth were assumed to be related to the mineral density. The fracture risk at different tooth portions was assessed for root canal treatments. The micro-CT images of a tooth were processed by a Matlab software programme and the CT numbers were retrieved. The tooth contours were obtained with thresholding segmentation using Amira. The inner and outer surfaces of the tooth were imported into Solidworks and a three-dimensional (3D) tooth model was constructed. An assembly of the tooth model with the periodontal ligament (PDL) layer and surrounding bone was imported into ABAQUS. The material properties of the tooth were calculated from the retrieved CT numbers via ABAQUS user's subroutines. Three root canal geometries (original and two enlargements) were investigated. The proposed method in this study can generate detailed 3D finite element models of a tooth with different root canal enlargements and filling materials, and would be very useful for the assessment of the fracture risk at different tooth portions after root canal treatments. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Inhibition of Wnt signaling by Wise (Sostdc1) and negative feedback from Shh controls tooth number and patterning.

PubMed

Ahn, Youngwook; Sanderson, Brian W; Klein, Ophir D; Krumlauf, Robb

2010-10-01

Mice carrying mutations in Wise (Sostdc1) display defects in many aspects of tooth development, including tooth number, size and cusp pattern. To understand the basis of these defects, we have investigated the pathways modulated by Wise in tooth development. We present evidence that, in tooth development, Wise suppresses survival of the diastema or incisor vestigial buds by serving as an inhibitor of Lrp5- and Lrp6-dependent Wnt signaling. Reducing the dosage of the Wnt co-receptor genes Lrp5 and Lrp6 rescues the Wise-null tooth phenotypes. Inactivation of Wise leads to elevated Wnt signaling and, as a consequence, vestigial tooth buds in the normally toothless diastema region display increased proliferation and continuous development to form supernumerary teeth. Conversely, gain-of-function studies show that ectopic Wise reduces Wnt signaling and tooth number. Our analyses demonstrate that the Fgf and Shh pathways are major downstream targets of Wise-regulated Wnt signaling. Furthermore, our experiments revealed that Shh acts as a negative-feedback regulator of Wnt signaling and thus determines the fate of the vestigial buds and later tooth patterning. These data provide insight into the mechanisms that control Wnt signaling in tooth development and into how crosstalk among signaling pathways controls tooth number and morphogenesis.

Varanoid Tooth Eruption and Implantation Modes in a Late Cretaceous Mosasaur.

PubMed

Liu, Min; Reed, David A; Cecchini, Giancarlo M; Lu, Xuanyu; Ganjawalla, Karan; Gonzales, Carol S; Monahan, Richard; Luan, Xianghong; Diekwisch, Thomas G H

2016-01-01

Erupting teeth are some of the oldest witnesses of developmental processes in the vertebrate fossil record and provide an important resource for vertebrate cladistics. Here, we have examined a mosasaur jaw fragment from central Texas using ultrathin ground section histology and 3D tomographic imaging to assess features critical for the cladistic placement of mosasaurs among varanoids vs. snakes: (i) the orientation of replacement teeth compared to the major tooth axis, (ii) the occurrence of resorption pits, and (iii) the mode of tooth implantation/attachment to the tooth bearing element (TBE). The replacement tooth studied here developed in an inclined position slightly distal of the deciduous parent tooth, similar to another varanoid squamate, the Gila monster Heloderma suspectum. Ground sections and tomographs also demonstrated that the replacement tooth attachment apparatus was entirely intact and that there was no evidence of mechanical deformation. Sections and tomographs further illustrated that the replacement tooth was located within a bony crypt and the inclination of the crypt matched the inclination of the replacement tooth. These preparations also revealed the presence of a resorption pit within the boundaries of the deciduous tooth that surrounded the developing replacement tooth. This finding suggests that developing mosasaur teeth developed within the walls of resorption pits similar to varanoid tooth germs and unlike developing snake teeth which are surrounded by fibrous connective tissue integuments. Finally, mosasaurs featured pseudo-thecodont tooth implantation with teeth anchored within a socket of mineralized tissue by means of a mineralized periodontal ligament. Together, these data indicate that the moderate inclination of the erupting mosasaur tooth studied here is neither a result of postmortem displacement nor a character representative of snakes, but rather a shared character between Mosasaurs and other varanoids such as Heloderma. In conjunction with the presence of resorption pits and the evidence for pseudothecodont tooth implantation, the tooth eruption and implantation characters described in the present study either place mosasaurs among the varanoids or suggest convergent evolution mechanisms between both clades, with mosasaurs evolving somewhat independently from a common varanoid ancestor.

Varanoid Tooth Eruption and Implantation Modes in a Late Cretaceous Mosasaur

PubMed Central

Liu, Min; Reed, David A.; Cecchini, Giancarlo M.; Lu, Xuanyu; Ganjawalla, Karan; Gonzales, Carol S.; Monahan, Richard; Luan, Xianghong

2016-01-01

Erupting teeth are some of the oldest witnesses of developmental processes in the vertebrate fossil record and provide an important resource for vertebrate cladistics. Here, we have examined a mosasaur jaw fragment from central Texas using ultrathin ground section histology and 3D tomographic imaging to assess features critical for the cladistic placement of mosasaurs among varanoids vs. snakes: (i) the orientation of replacement teeth compared to the major tooth axis, (ii) the occurrence of resorption pits, and (iii) the mode of tooth implantation/attachment to the tooth bearing element (TBE). The replacement tooth studied here developed in an inclined position slightly distal of the deciduous parent tooth, similar to another varanoid squamate, the Gila monster Heloderma suspectum. Ground sections and tomographs also demonstrated that the replacement tooth attachment apparatus was entirely intact and that there was no evidence of mechanical deformation. Sections and tomographs further illustrated that the replacement tooth was located within a bony crypt and the inclination of the crypt matched the inclination of the replacement tooth. These preparations also revealed the presence of a resorption pit within the boundaries of the deciduous tooth that surrounded the developing replacement tooth. This finding suggests that developing mosasaur teeth developed within the walls of resorption pits similar to varanoid tooth germs and unlike developing snake teeth which are surrounded by fibrous connective tissue integuments. Finally, mosasaurs featured pseudo-thecodont tooth implantation with teeth anchored within a socket of mineralized tissue by means of a mineralized periodontal ligament. Together, these data indicate that the moderate inclination of the erupting mosasaur tooth studied here is neither a result of postmortem displacement nor a character representative of snakes, but rather a shared character between Mosasaurs and other varanoids such as Heloderma. In conjunction with the presence of resorption pits and the evidence for pseudothecodont tooth implantation, the tooth eruption and implantation characters described in the present study either place mosasaurs among the varanoids or suggest convergent evolution mechanisms between both clades, with mosasaurs evolving somewhat independently from a common varanoid ancestor. PMID:27242535

Influence of roughness bottom on the dynamics of a buoyant cloud : application to a powder avalanche

NASA Astrophysics Data System (ADS)

Brossard, D.; Naaim-Bouvet, F.; Naaim, M.; Caccamo, P.

2009-04-01

A powder avalanche is referred to as a turbulent flow of snow particles in air. In the past such avalanches have been modelled by buoyant cloud in a watertank: buoyant clouds flow along an inclined plane from a small immersed tank with a release gate (injection is of short duration). The powder avalanches are simulated by a heavy fluid (salt water + colorant or kaolin) which is dispersing in a lighter one. Such experiments allow studies for the influence of roughness bottoms on the dynamics of a buoyant clouds. The authors studied the flows of buoyant clouds on an uniform slope of 20° with different roughness: smooth PVC, abrasive paper, bottom covered with glued particles of PMMA or with glued glass beads of different sizes arranged in a compact way. The released volume varies between 2 to 4 liters and the density of salted water is 1.2. Two cameras are used to obtain the height together with the front velocity. Inside the study area the front velocity is approximately constant and the height of the clouds varies linearly with the distance from the released gate as usually observed in previous experiments. So for each roughness a front velocity and height growth can be defined. It was shown from the experiments that: As the bottom increases in roughness, the front speed increases and the height growth decreases. Nevertheless the height of glued elements does not seem to be the most appropriate parameter to characterize the roughness.

Very Deep Multilingual Convolutional Neural Networks for LVCSR (Author’s Manuscript)

DTIC Science & Technology

2016-05-19

Courant Institute of Mathematical Sciences, New York University 2 IBM T. J . Watson Research Center, Yorktown Heights, NY, 10598, U.S.A. 2{tsercu...related to the frequency fi of context dependent state CDi as pi = f γ i∑ j f γ j . After sampling y, we sample uniformly across all frames with that...C-0012. The U.S. Government is authorized to reproduce and distribute reprints for Governmental purposes notwithstanding any copyright anno - tation

Initiation Phenomena in Pulsed Chemical Lasers

DTIC Science & Technology

1978-10-01

2-3 4 Normalized Cavity llumination Contours.............. 2-5 5 Case B ....... * . . .. ... . ...... . . . .. .. . ... . 2-6 6 Nonuniformity in...improvement in illumination uniformity were obtained. Figure 6 shows the decrease in initiation nonuniformity with increasing numbers of lamps in the...Flow10 Entry and Exit < 6 4 2 10 14 18 22 26 30 34 Number of Lamps 1.0 1.4 1.8 2.2 2.6 3.0 3.4 Cavity Width/Cavity Height Figure 6. Nonuniformity in

Comparing simulated and measured sensible and latent heat fluxes over snow under a pine canopy to improve an energy balance snowmelt model

Treesearch

D. Marks; M. Reba; J. Pomeroy; T. Link; A. Winstral; G. Flerchinger; K. Elder

2008-01-01

During the second year of the NASA Cold Land Processes Experiment (CLPX), an eddy covariance (EC) system was deployed at the Local Scale Observation Site (LSOS) from mid-February to June 2003. The EC system was located beneath a uniform pine canopy, where the trees are regularly spaced and are of similar age and height. In an effort to evaluate the turbulent flux...

Performance of USDA guayule lines in the Northern Negev of Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mills, D.; Benzioni, A.; Forti, M.

The rubber yield of the guayule plant (Parthenium argentatum) is determined by its rubber concentration and biomass production, both of which are a function of genetic constituents and environmental conditions. With the aim of selecting best performing lines of guayule under the climatic conditions of the northern Negev of Israel, two-yr-old guayule plants from 13 USDA lines were evaluated for height, spread, canopy fresh and dry weight, branch and leaf dry weight, rubber and resin concentration, and rubber and resin yield per plant. Significant differences were found among the lines for all the characteristics tested. Lines 11600 and 11604 excelledmore » in rubber and biomass production and were taller and more uniform than the other lines; whereas line N593, conventionally used as a standard, performed poorly and was less uniform. The correlation between rubber yield per plant and rubber concentration was poor, rubber yield being related mainly to biomass production and to a lesser degree to height and spread of the plants. Taken together with fact that biomass production was more variable than rubber concentration, this finding suggests that breeding and selection of guayule and for high rubber yield should be directed primarily towards improvement of biomass production rather than rubber concentration. In the northern Negev of Israel, USDA lines 11600 and 11604 performed well.« less

Kinematics modeling and experimentation of the multi-manipulator tooth-arrangement robot for full denture manufacturing.

PubMed

Zhang, Yong-de; Jiang, Jin-gang; Liang, Ting; Hu, Wei-ping

2011-12-01

Artificial teeth are very complicated in shape, and not easy to be grasped and manipulated accurately by a single robot. The method of tooth-arrangement by multi-manipulator for complete denture manufacturing proposed in this paper. A novel complete denture manufacturing mechanism is designed based on multi-manipulator and dental arch generator. Kinematics model of the multi-manipulator tooth-arrangement robot is built by analytical method based on tooth-arrangement principle for full denture. Preliminary experiments on tooth-arrangement are performed using the multi-manipulator tooth-arrangement robot prototype system. The multi-manipulator tooth-arrangement robot prototype system can automatically design and manufacture a set of complete denture that is suitable for a patient according to the jaw arch parameters. The experimental results verified the validity of kinematics model of the multi-manipulator tooth-arrangement robot and the feasibility of the manufacture strategy of complete denture fulfilled by multi-manipulator tooth-arrangement robot.

Orthodontic Tooth Movement: A Historic Prospective.

PubMed

Will, Leslie A

2016-01-01

The earliest report on orthodontic tooth movement in the English literature was published in 1911. Oppenheim carried out studies on baboons to determine what histologic changes occurred during tooth movement. Reitan and many others carried out research into the nature of tooth movement. The pressure-tension model of tooth movement developed from these studies, whereby the two sides of the tooth responded to forces as if in isolation. A second theory, proposed by Stuteville in 1938, was the hydraulic theory of tooth movement. In this theory, fluid from the vasculature, lymphatic system and intercellular spaces responds to the forces of tooth movement, damping the force and limiting movement. Bien and Baumrind expanded on this theory with their own studies in the 1960s. It is clear that both the pressure-tension and fluid flow concepts have merit, but considerable work needs to be done to ascertain the details so that tooth movement can be managed and controlled. © 2016 S. Karger AG, Basel.

Tooth Eruption without Roots

PubMed Central

2013-01-01

Root development and tooth eruption are very important topics in dentistry. However, they remain among the less-studied and -understood subjects. Root development accompanies rapid tooth eruption, but roots are required for the movement of teeth into the oral cavity. It has been shown that the dental follicle and bone remodeling are essential for tooth eruption. So far, only limited genes have been associated with root formation and tooth eruption. This may be due to the difficulties in studying late stages of tooth development and tooth movement and the lack of good model systems. Transgenic mice with eruption problems and short or no roots can be used as a powerful model for further deciphering of the cellular, molecular, and genetic mechanisms underlying root formation and tooth eruption. Better understanding of these processes can provide hints on delivering more efficient dental therapies in the future. PMID:23345536

Textured micrometer scale templates as light managing fabrication platform for organic solar cells

DOEpatents

Chaudhary, Sumit; Ho, Kai-Ming; Park, Joong-Mok; Nalwa, Kanwar Singh; Leung, Wai Y.

2016-07-26

A three-dimensional, microscale-textured, grating-shaped organic solar cell geometry. The solar cells are fabricated on gratings to give them a three-dimensional texture that provides enhanced light absorption. Introduction of microscale texturing has a positive effect on the overall power conversion efficiency of the devices. This grating-based solar cell having a grating of pre-determined pitch and height has shown improved power-conversion efficiency over a conventional flat solar cell. The improvement in efficiency is accomplished by homogeneous coverage of the grating with uniform thickness of the active layer, which is attributed to a sufficiently high pitch and low height of the underlying gratings. Also the microscale texturing leads to suppressed reflection of incident light due to the efficient coupling of the incident light into modes that are guided in the active layer.

Modeling of Beams’ Multiple-Contact Mode with an Application in the Design of a High-g Threshold Microaccelerometer

PubMed Central

Li, Kai; Chen, Wenyuan; Zhang, Weiping

2011-01-01

Beam’s multiple-contact mode, characterized by multiple and discrete contact regions, non-uniform stoppers’ heights, irregular contact sequence, seesaw-like effect, indirect interaction between different stoppers, and complex coupling relationship between loads and deformation is studied. A novel analysis method and a novel high speed calculation model are developed for multiple-contact mode under mechanical load and electrostatic load, without limitations on stopper height and distribution, providing the beam has stepped or curved shape. Accurate values of deflection, contact load, contact region and so on are obtained directly, with a subsequent validation by CoventorWare. A new concept design of high-g threshold microaccelerometer based on multiple-contact mode is presented, featuring multiple acceleration thresholds of one sensitive component and consequently small sensor size. PMID:22163897

Evidence of correlated evolution of hypsodonty and exceptional longevity in endemic insular mammals.

PubMed

Jordana, Xavier; Marín-Moratalla, Nekane; DeMiguel, Daniel; Kaiser, Thomas M; Köhler, Meike

2012-08-22

Here, we test whether the increase in tooth height in insular endemics results from the expansion of the dietary niche under resource limitation, as widely considered, or whether it represents an investment in dental durability in response to the selection for extended longevity under low levels of extrinsic mortality. We tested these hypotheses in the extremely hypsodont fossil bovid Myotragus balearicus from the Balearic Islands, an ideal model to study the evolutionary trends on islands. Dental abrasion was significantly lower in the insular bovid than in highly hypsodont continental artiodactyls, suggesting that feeding habits are not the sole driving force behind increased crown height. However, the estimated longevity for M. balearicus based on dental durability was two times that predicted from body mass. Survivorship curves confirm that an extraordinarily large number of individuals approached the longevity of the species. Our results, hence, provide evidence that hypsodonty in insular endemics is the outcome of selection for increased durability of the permanent dentition in association with an extended lifespan. In the context of insularity, our results lend additional support to the disposable soma theory of ageing confirming the dependency of somatic maintenance and repair on lifespan, and its control by resource availability and extrinsic mortality.

Evidence of correlated evolution of hypsodonty and exceptional longevity in endemic insular mammals

PubMed Central

Jordana, Xavier; Marín-Moratalla, Nekane; DeMiguel, Daniel; Kaiser, Thomas M.; Köhler, Meike

2012-01-01

Here, we test whether the increase in tooth height in insular endemics results from the expansion of the dietary niche under resource limitation, as widely considered, or whether it represents an investment in dental durability in response to the selection for extended longevity under low levels of extrinsic mortality. We tested these hypotheses in the extremely hypsodont fossil bovid Myotragus balearicus from the Balearic Islands, an ideal model to study the evolutionary trends on islands. Dental abrasion was significantly lower in the insular bovid than in highly hypsodont continental artiodactyls, suggesting that feeding habits are not the sole driving force behind increased crown height. However, the estimated longevity for M. balearicus based on dental durability was two times that predicted from body mass. Survivorship curves confirm that an extraordinarily large number of individuals approached the longevity of the species. Our results, hence, provide evidence that hypsodonty in insular endemics is the outcome of selection for increased durability of the permanent dentition in association with an extended lifespan. In the context of insularity, our results lend additional support to the disposable soma theory of ageing confirming the dependency of somatic maintenance and repair on lifespan, and its control by resource availability and extrinsic mortality. PMID:22535784

Monte Carlo simulation for light propagation in 3D tooth model

NASA Astrophysics Data System (ADS)

Fu, Yongji; Jacques, Steven L.

2011-03-01

Monte Carlo (MC) simulation was implemented in a three dimensional tooth model to simulate the light propagation in the tooth for antibiotic photodynamic therapy and other laser therapy. The goal of this research is to estimate the light energy deposition in the target region of tooth with given light source information, tooth optical properties and tooth structure. Two use cases were presented to demonstrate the practical application of this model. One case was comparing the isotropic point source and narrow beam dosage distribution and the other case was comparing different incident points for the same light source. This model will help the doctor for PDT design in the tooth.

Comminution process to produce engineered wood particles of uniform size and shape with disrupted grain structure from veneer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooley, James H; Lanning, David N

Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) substantially equal to the veneer thickness (Tv) and aligned normal to Wmore » and L, wherein the W.times.H dimensions define a pair of substantially parallel end surfaces with end checking between crosscut fibers.« less

Pressure Measurement Studies on a 1:1.5:7 Rectangular High Rise Building Model under Uniform Flow

NASA Astrophysics Data System (ADS)

Sarath Kumar, H.; Vijaya Bhaskar Reddy, P.

2017-08-01

This paper presents the experimental results of evaluate wind pressure distributions on all four faces of a rectangular tall building with 1:1.5:7 ratio. The model is made up of acrylic sheet with a geometric scale of 1:300 with plan dimension of 10 cm x 15 cm and height of 70 cm. The model is tested using a Boundary Layer Wind Tunnel (BLWT) twelve angles (0°, 5°, 10°, 15°, 25°, 33.5°, 45°, 56.5°, 60°, 75°, 87.5° & 90°) of wind incidence under uniform flow condition. Mean and standard deviation of pressure coefficients, drag & lift coefficients along wind direction and perpendicular to wind direction, mean moment coefficient are calculated from pressure measurement on the model.

Improved design of a cone-shaped rotating disk for shear force loading in a cell culture plate

NASA Astrophysics Data System (ADS)

Keawprachum, Boonrit; Limjeerajarus, Nuttapol; Nakalekha Limjeerajarus, Chalida; Srisungsitthisunti, Pornsak

2018-01-01

In our previous study, a cone-shaped rotating disk had been designed and proposed for generating shear force on the cell in a cell culture plate. This study aims to improve the design of the rotating disk that could provide a better uniformity of shear stress distribution. The top of the cone was designed to be trimmed off to obtain a flat head area. The effect of tilt angle (θ) was numerically studied using computational fluid dynamics (CFD) technique in ANSYS-Fluent software. The results revealed that for 500 rpm, the new designed rotating disk with a height of cone-shaped top to the plate bottom h = 1 mm and θ = 25° provided the best uniformity of 0.820 which was better than that of the previously designed.

New rules of thumb maximizing energy efficiency in street lighting with discharge lamps: The general equations for lighting design

NASA Astrophysics Data System (ADS)

Peña-García, A.; Gómez-Lorente, D.; Espín, A.; Rabaza, O.

2016-06-01

New relationships between energy efficiency, illuminance uniformity, spacing and mounting height in public lighting installations were derived from the analysis of a large sample of outputs generated with a widely used software application for lighting design. These new relationships greatly facilitate the calculation of basic lighting installation parameters. The results obtained are also based on maximal energy efficiency and illuminance uniformity as a premise, which are not included in more conventional methods. However, these factors are crucial since they ensure the sustainability of the installations. This research formulated, applied and analysed these new equations. The results of this study highlight their usefulness in rapid planning and urban planning in developing countries or areas affected by natural disasters where engineering facilities and computer applications for this purpose are often unavailable.

Can dead man tooth do tell tales? Tooth prints in forensic identification.

PubMed

Christopher, Vineetha; Murthy, Sarvani; Ashwinirani, S R; Prasad, Kulkarni; Girish, Suragimath; Vinit, Shashikanth Patil

2017-01-01

We know that teeth trouble us a lot when we are alive, but they last longer for thousands of years even after we are dead. Teeth being the strongest and resistant structure are the most significant tool in forensic investigations. Patterns of enamel rod end on the tooth surface are known as tooth prints. This study is aimed to know whether these tooth prints can become a forensic tool in personal identification such as finger prints. A study has been targeted toward the same. In the present in-vivo study, acetate peel technique has been used to obtain the replica of enamel rod end patterns. Tooth prints of upper first premolars were recorded from 80 individuals after acid etching using cellulose acetate strips. Then, digital images of the tooth prints obtained at two different intervals were subjected to biometric conversion using Verifinger standard software development kit version 6.5 software followed by the use of Automated Fingerprint Identification System (AFIS) software for comparison of the tooth prints. Similarly, each individual's finger prints were also recorded and were subjected to the same software. Further, recordings of AFIS scores obtained from images were statistically analyzed using Cronbach's test. We observed that comparing two tooth prints taken from an individual at two intervals exhibited similarity in many cases, with wavy pattern tooth print being the predominant type. However, the same prints showed dissimilarity when compared with other individuals. We also found that most of the individuals with whorl pattern finger print showed wavy pattern tooth print and few loop type fingerprints showed linear pattern of tooth prints. Further more experiments on both tooth prints and finger prints are required in establishing an individual's identity.

Can dead man tooth do tell tales? Tooth prints in forensic identification

PubMed Central

Christopher, Vineetha; Murthy, Sarvani; Ashwinirani, S. R.; Prasad, Kulkarni; Girish, Suragimath; Vinit, Shashikanth Patil

2017-01-01

Background: We know that teeth trouble us a lot when we are alive, but they last longer for thousands of years even after we are dead. Teeth being the strongest and resistant structure are the most significant tool in forensic investigations. Patterns of enamel rod end on the tooth surface are known as tooth prints. Aim: This study is aimed to know whether these tooth prints can become a forensic tool in personal identification such as finger prints. A study has been targeted toward the same. Settings and Design: In the present in-vivo study, acetate peel technique has been used to obtain the replica of enamel rod end patterns. Materials and Methods: Tooth prints of upper first premolars were recorded from 80 individuals after acid etching using cellulose acetate strips. Then, digital images of the tooth prints obtained at two different intervals were subjected to biometric conversion using Verifinger standard software development kit version 6.5 software followed by the use of Automated Fingerprint Identification System (AFIS) software for comparison of the tooth prints. Similarly, each individual's finger prints were also recorded and were subjected to the same software. Statistical Analysis: Further, recordings of AFIS scores obtained from images were statistically analyzed using Cronbach's test. Results: We observed that comparing two tooth prints taken from an individual at two intervals exhibited similarity in many cases, with wavy pattern tooth print being the predominant type. However, the same prints showed dissimilarity when compared with other individuals. We also found that most of the individuals with whorl pattern finger print showed wavy pattern tooth print and few loop type fingerprints showed linear pattern of tooth prints. Conclusions: Further more experiments on both tooth prints and finger prints are required in establishing an individual's identity. PMID:28584483

How to Prevent Tooth Decay in Your Baby

MedlinePlus

... life-threatening infections. Tooth decay (called early childhood caries) is the most common chronic infectious disease of childhood. Tooth decay may also be called nursing caries or baby bottle tooth decay . Healthy dental habits ...

Alveolar ridge preservation after tooth extraction: a Bayesian Network meta-analysis of grafting materials efficacy on prevention of bone height and width reduction.

PubMed

Iocca, Oreste; Farcomeni, Alessio; Pardiñas Lopez, Simon; Talib, Huzefa S

2017-01-01

To conduct a traditional meta-analysis and a Bayesian Network meta-analysis to synthesize the information coming from randomized controlled trials on different socket grafting materials and combine the resulting indirect evidence in order to make inferences on treatments that have not been compared directly. RCTs were identified for inclusion in the systematic review and subsequent statistical analysis. Bone height and width remodelling were selected as the chosen summary measures for comparison. First, a series of pairwise meta-analyses were performed and overall mean difference (MD) in mm with 95% CI was calculated between grafted versus non-grafted sockets. Then, a Bayesian Network meta-analysis was performed to draw indirect conclusions on which grafting materials can be considered most likely the best compared to the others. From the six included studies, seven comparisons were obtained. Traditional meta-analysis showed statistically significant results in favour of grafting the socket compared to no-graft both for height (MD 1.02, 95% CI 0.44-1.59, p value < 0.001) than for width (MD 1.52 95% CI 1.18-1.86, p value <0.000001) remodelling. Bayesian Network meta-analysis allowed to obtain a rank of intervention efficacy. On the basis of the results of the present analysis, socket grafting seems to be more favourable than unassisted socket healing. Moreover, Bayesian Network meta-analysis indicates that freeze-dried bone graft plus membrane is the most likely effective in the reduction of bone height remodelling. Autologous bone marrow resulted the most likely effective when width remodelling was considered. Studies with larger samples and less risk of bias should be conducted in the future in order to further strengthen the results of this analysis. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Tooth loss patterns in older adults with special needs: a Minnesota cohort

PubMed Central

Chen, Xi; Clark, Jennifer J

2011-01-01

This study was conducted to detail tooth loss patterns in older adults with special needs. A total of 491 elderly subjects with special needs were retrospectively selected and followed during 10/1999-12/2006. Medical, dental, cognitive, and functional assessments were abstracted from dental records and used to predict risk of tooth loss. Tooth loss events were recorded for subjects during follow-up. Chi-squared tests were used to study the association between tooth loss and the selected risk factors. Logistic, poisson, and negative binomial regressions were developed to study tooth loss patterns. Overall, 27% of the subjects lost at least one tooth during follow-up. Fourteen subjects had tooth loss events per 100 person-years. Tooth loss pattern did not differ significantly among different special-needs subgroups (i.e. community-dwelling vs. long-term care, physically disabled vs. functionally independent). Special-needs subjects with three or more active dental conditions at arrival had more than twice the risk of losing teeth than those without any existing conditions. After adjusting other factors, the number of carious teeth or retained roots at arrival was a significant predictor of tooth loss for older adults with special needs (P=0.001). These findings indicate that appropriately managing active caries and associated conditions is important to prevent tooth loss for older adults with special needs. PMID:21449213

[Establishment of database with standard 3D tooth crowns based on 3DS MAX].

PubMed

Cheng, Xiaosheng; An, Tao; Liao, Wenhe; Dai, Ning; Yu, Qing; Lu, Peijun

2009-08-01

The database with standard 3D tooth crowns has laid the groundwork for dental CAD/CAM system. In this paper, we design the standard tooth crowns in 3DS MAX 9.0 and create a database with these models successfully. Firstly, some key lines are collected from standard tooth pictures. Then we use 3DS MAX 9.0 to design the digital tooth model based on these lines. During the design process, it is important to refer to the standard plaster tooth model. After some tests, the standard tooth models designed with this method are accurate and adaptable; furthermore, it is very easy to perform some operations on the models such as deforming and translating. This method provides a new idea to build the database with standard 3D tooth crowns and a basis for dental CAD/CAM system.

A windowing and mapping strategy for gear tooth fault detection of a planetary gearbox

NASA Astrophysics Data System (ADS)

Liang, Xihui; Zuo, Ming J.; Liu, Libin

2016-12-01

When there is a single cracked tooth in a planet gear, the cracked tooth is enmeshed for very short time duration in comparison to the total time of a full revolution of the planet gear. The fault symptom generated by the single cracked tooth may be very weak. This study aims to develop a windowing and mapping strategy to interpret the vibration signal of a planetary gear at the tooth level. The fault symptoms generated by a single cracked tooth of the planet gear of interest can be extracted. The health condition of the planet gear can be assessed by comparing the differences among the signals of all teeth of the planet gear. The proposed windowing and mapping strategy is tested with both simulated vibration signals and experimental vibration signals. The tooth signals can be successfully decomposed and a single tooth fault on a planet gear can be effectively detected.

The tooth, the whole tooth and nothing but the tooth: tooth shape and ontogenetic shift dynamics in the white shark Carcharodon carcharias.

PubMed

French, G C A; Stürup, M; Rizzuto, S; van Wyk, J H; Edwards, D; Dolan, R W; Wintner, S P; Towner, A V; Hughes, W O H

2017-10-01

Results from this study of the white shark Carcharodon carcharias include measurements obtained using a novel photographic method that reveal significant differences between the sexes in the relationship between tooth cuspidity and shark total length, and a novel ontogenetic change in male tooth shape. Males exhibit broader upper first teeth and increased distal inclination of upper third teeth with increasing length, while females do not present a consistent morphological change. Substantial individual variation, with implications for pace of life syndrome, was present in males and tooth polymorphism was suggested in females. Sexual differences and individual variation may play major roles in ontogenetic changes in tooth morphology in C. carcharias, with potential implications for their foraging biology. Such individual and sexual differences should be included in studies of ontogenetic shift dynamics in other species and systems. © 2017 The Fisheries Society of the British Isles.

Solvothermal transformation of a calcium oleate precursor into large-sized highly ordered arrays of ultralong hydroxyapatite microtubes.

PubMed

Lu, Bing-Qiang; Zhu, Ying-Jie; Chen, Feng; Qi, Chao; Zhao, Xin-Yu; Zhao, Jing

2014-06-02

Hydroxyapatite (HAP), a well-known member of the calcium phosphate family, is the major inorganic component of bones and teeth in vertebrates. The highly ordered arrays of HAP structures are of great significance for hard tissue repair and for understanding the formation mechanisms of bones and teeth. However, the synthesis of highly ordered HAP structure arrays remains a great challenge. In this work, inspired by the ordered structure of tooth enamel, we have successfully synthesized three-dimensional bulk materials with large sizes (millimeter scale) that are made of highly ordered arrays of ultralong HAP microtubes (HOAUHMs) by solvothermal transformation of calcium oleate precursor. The core-shell-structured oblate sphere consists of a core that is composed of HAP nanorods and a shell that consists of highly ordered HAP microtube arrays. The prepared HOAUHMs are large: 6.0 mm in diameter and up to 1.4 mm in thickness. With increasing solvothermal reaction time, the HOAUHMs grow larger; the microtubes become more uniform and more ordered. This work provides a new synthetic method for synthesizing highly ordered arrays of uniform HAP ultralong microtubes that are promising for biomedical applications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tripylella australis sp. nov. and Tripyla setifera Bütschli 1873 (Nematoda: Triplonchida: Tripylidae) from Australia.

PubMed

Xu, Yu Mei; Zhao, Zeng Qi; Davies, Kerrie A; Wang, Jian Ming

2017-04-03

This paper describes a new species of Tripylella and gives a new record of Tripyla (family Tripylidae) in Australia, and provides a key to species in the genus Tripylella. Tripylella australis sp. nov. is characterized by having females with a long body (1804-1832 μm), a=41-42, b= 4.4-4.5, c=10.3-11.3, c'=5.4-6.4 and V=51-54%, outer labial setae 13-14 μm long and cephalic setae 3.7-4.5 μm long in one whorl, dorsal tooth posterior to two subventral teeth, tail tapering uniformly, and four single caudal setae on the dorsal part of the tail. Males are similar to females, and have a long body (1870-2014 μm), a=50-55, b= 4.7-4.9, c=11.3-11.4, c'=5.8-6.0 and T=53-56%, horn-shaped spicules, 36-38 μm long, a straight gubernaculum 14-16 μm in length, tail tapering almost uniformly, and four caudal setae on the dorsal part of the tail. A key for identification of Tripylella species is presented. Tripyla setifera Bütschli 1873 is recorded for the first time in Australia, and is re-described.

A new method for measuring nocturnal tooth contacts.

PubMed

Yamashita, S; Ai, M; Mizutani, H

1993-09-01

A new portable system for measuring nocturnal tooth contacts has been devised. This system was suitable for patients to take home and record tooth contacts by themselves. A micro photo sensor using optical fibres was applied to detect tooth contacts. The sensor and the target were accurately fixed to opposed molars, respectively on the same side, with removable metal attachments. Patients were instructed to set the attachment to their tooth each experimental night. In the present study, data was assembled for four or five nights in three subjects who were free of masticatory pain and dysfunction. Each subject showed an individual tooth contact pattern. It is suggested that this new system is useful and convenient for measuring nocturnal tooth contacts.

Soft tissue grafting to improve implant esthetics

PubMed Central

Kassab, Moawia M

2010-01-01

Dental implants are becoming the treatment of choice to replace missing teeth, especially if the adjacent teeth are free of restorations. When minimal bone width is present, implant placement becomes a challenge and often resulting in recession and dehiscence around the implant that leads to subsequent gingival recession. To correct such defect, the author turned to soft tissue autografting and allografting to correct a buccal dehiscence around tooth #24 after a malpositioned implant placed by a different surgeon. A 25-year-old woman presented with the chief complaint of gingival recession and exposure of implant threads around tooth #24. The patient received three soft tissue grafting procedures to augment the gingival tissue. The first surgery included a connective tissue graft to increase the width of the keratinized gingival tissue. The second surgery included the use of autografting (connective tissue graft) to coronally position the soft tissue and achieve implant coverage. The third and final surgery included the use of allografting material Alloderm to increase and mask the implant from showing through the gingiva. Healing period was uneventful for the patient. After three surgical procedures, it appears that soft tissue grafting has increased the width and height of the gingiva surrounding the implant. The accomplished thickness of gingival tissue appeared to mask the showing of implant threads through the gingival tissue and allowed for achieving the desired esthetic that the patient desired. The aim of the study is to present a clinical case with soft tissue grafting procedures. PMID:23662087

Growth of second stage mineral in Lytechinus variegatus.

PubMed

Stock, S R; Seto, Jong; Deymier, A C; Rack, A; Veis, A

2017-10-30

Purpose and Aims: Sea urchin teeth consist of calcite and form in two stages with different magnesium contents. The first stage structures of independently formed plates and needle-prisms define the shape of the tooth, and the columns of the second stage mineral cements the first stage structures together and control the fracture behavior of the mature tooth. This study investigates the nucleation and growth of the second stage mineral. Scanning electron microscopy (SEM) and synchrotron microComputed Tomography characterized the structures of the second phase material found in developing of Lytechinus variegatus teeth. Although the column development is a continuous process, defining four phases of column formation captures the changes that occur in teeth of L. variegatus. The earliest phase consists of small 1-2 µm diameter hemispheres, and the second of 5-10 µm diameter, mound-like structures with a nodular surface, develops from the hemispheres. The mounds eventually bridge the syncytium between adjacent plates and form hyperboloid structures (phase three) that appear like mesas when plates separate during the fracture. The mesa diameter increases with time until the column diameter is significantly larger than its height, defining the fourth phase of column development. Energy dispersive x-ray spectroscopy confirms that the columns contain more magnesium than the underlying plates; the ratios of magnesium to calcium are consistent with compositions derived from x-ray diffraction. Columns grow from both bounding plates. The presence of first phase columns interspersed among third stage mesas indicates very localized control of mineralization.

The functional significance of morphological changes in the dentitions of early mammals.

PubMed

Conith, Andrew J; Imburgia, Michael J; Crosby, Alfred J; Dumont, Elizabeth R

2016-11-01

The Mesozoic marked a time of experimentation in the tooth morphology of early mammals. One particular experiment involved the movement of three points, or cusps, on the surface of a molar tooth from a line into a triangle. This transition is exemplified by two extinct insectivorous mammals, Morganucodon (cusps in a line) and Kuehneotherium (cusps in a triangle). Here we test whether this difference in cusp arrangement, alongside cusp heights and angles between cusps, is associated with differences in the ability of the teeth to fracture proxy-insect prey. We gathered measurements from molar teeth of both species and used them to create physical models. We then measured the force, time and energy at fracture and peak force, and the amount of damage inflicted by the models on hard and soft gels encased in a tough film that mimicked the material properties of insects. The Morganucodon model required less force and energy to fracture hard gels and reach peak force compared with Kuehneotherium Kuehneotherium required a similar time, force and energy to fracture soft gels but reduced the time, force and energy to reach peak force. More importantly, Kuehneotherium also inflicted more damage to both the hard and the soft gels. These results suggest that changes in dental morphology in some early mammals was driven primarily by selection for maximizing damage, and secondarily for maximizing biomechanical efficiency for a given food material property. © 2016 The Author(s).

Handwriting difficulties of children with Charcot-Marie-Tooth disease type 1A.

PubMed

Kunovsky, Daniel; Cordier, Reinie; Bray, Paula; Burns, Joshua

2017-03-01

Hand weakness and impaired manual dexterity have been reported in children with Charcot-Marie-Tooth disease type 1A (CMT1A). This early onset of upper limb involvement might explain frequent clinical referrals for assessment and treatment of impaired handwriting performance. The aim of this study was to examine the impact of CMT1A on handwriting speed and legibility, and identify demographic, anthropometric, and physical measures that might relate to handwriting performance. Handwriting speed (Handwriting Speed Test), handwriting legibility (Evaluation Tool of Children's Handwriting-Cursive), and hand strength (hand-held dynamometry of tip pinch, lateral pinch and grip) were assessed in 30 children with CMT1A (aged 8-17 years) and 30 age- and sex-matched controls. Children with CMT1A exhibited 34% slower handwriting speed (p < 0.0001) with 4% reduced legibility (p = 0.001) and 37-48% lower hand strength (p < 0.0001). All measures of strength, age, height, and weight were positively associated with handwriting speed (r = 0.39-0.79, p < 0.01). None of these factors related to handwriting legibility (p > 0.05). Regression modelling identified a diagnosis of CMT1A, lateral pinch weakness and younger age as significant independent predictors of slower handwriting speed, explaining 78% of the variance. Children with CMT1A have considerable handwriting difficulties, primarily with speed, and substantial associated hand and finger weakness. Understanding the cause-effect relationship between strength and function might provide modifiable targets for upper limb intervention. © 2016 Peripheral Nerve Society.

Diversity in tooth eruption and life history in humans: illustration from a Pygmy population

PubMed Central

Ramirez Rozzi, Fernando

2016-01-01

Life history variables (LHV) in primates are closely correlated with the ages of tooth eruption, which are a useful proxy to predict growth and development in extant and extinct species. However, it is not known how tooth eruption ages interact with LHV in polymorphic species such as modern humans. African pygmies are at the one extreme in the range of human size variation. LHV in the Baka pygmies are similar to those in standard populations. We would therefore expect tooth eruption ages to be similar also. This mixed (longitudinal and cross-sectional) study of tooth eruption in Baka individuals of known age reveals that eruption in all tooth classes occurs earlier than in any other human population. Earlier tooth eruption can be related to the particular somatic growth in the Baka but cannot be correlated with LHV. The link between LHV and tooth eruption seems disrupted in H. sapiens, allowing adaptive variations in tooth eruption in response to different environmental constraints while maintaining the unique human life cycle. PMID:27305976

[Application of micro-power system in the surgery of tooth extraction].

PubMed

Kaijin, Hu; Yongfeng, Li

2015-02-01

Tooth extraction is a common operation in oral surgery. Traditional-extraction instruments, such as bone chisel, elevator, and bone hammer, lead to not only severe trauma but also unnecessary complications, and patients easily become nervous and apprehensive if tooth extraction is performed using these violent instruments. In recent years, with the develop- ment of minimally invasive concept and technology, various micro-power instruments have been used for tooth extraction. This innovative technology can reduce the iatrogenic trauma and complications of tooth extraction. Additionally, this technology can greatly decrease the patient's physical and mental pressure. The new equipment compensates for the deficiency of traditional tooth extraction equipment and facilitates the gradual replacement of the latter. Diverse micro-power systems have distinct strengths and weaknesses, so some auxiliary instruments are still needed during tooth extraction. This paper focuses on the various micro-power systems for tooth extraction and tries to compare the advantages and disadvantages of these systems. Selection and usage of auxiliary equipment are also introduced. Thus, this paper provides reference for the proper application of the micro-power systems in tooth extraction.

Associations between bacteremia from oral sources and distant-site infections: tooth brushing versus single tooth extraction.

PubMed

Mougeot, Farah K Bahrani; Saunders, Sabrina E; Brennan, Michael T; Lockhart, Peter B

2015-04-01

To determine the impact of antibiotic prophylaxis (AP) on the incidence of bacteremia caused by oral bacterial species associated with infective endocarditis (IE) and prosthetic joint infections (PJIs) and to compare the incidence of following tooth brushing versus single tooth extraction. Bacterial species in blood following single tooth extraction, with or without AP, and tooth brushing(1) were compared with IE- and PJI-associated bacteria reported in the literature. Of the 98 bacterial species identified in blood following single tooth extraction and tooth brushing, 32(1) and 12 were species were associated with IE and PJI, respectively. AP decreased the frequency of IE- and PJI-causing oral bacterial species in blood; however, single tooth extraction versus brushing resulted in bacteremia with IE- and PJI-causing species with similar frequencies: 65% versus 56% for IE, and 31% versus 28% for PJI. Although AP significantly decreased the incidence of bacteremia, the similarity between the incidence of bacteremia following brushing and extraction undermines AP as an effective strategy for the prevention of these distant-site infections. Copyright © 2015 Elsevier Inc. All rights reserved.

Bremsstrahlung from colour charges as a source of soft particle production in hadronic collisions

NASA Astrophysics Data System (ADS)

Bialas, A.; Jezabek, M.

2004-06-01

It is proposed that soft particle production in hadronic collisions is dominated by multiple gluon exchanges between partons from the colliding hadrons, followed by radiation of hadronic clusters from the coloured partons distributed uniformly in rapidity. This explains naturally two dominant features of the data: (a) the linear increase of rapidity spectra in the regions of limiting fragmentation and, (b) the proportionality between the increasing width of the limiting fragmentation region and the height of the central plateau.

FE analysis of conceptual hybrid composite endodontic post designs in anterior teeth.

PubMed

Gloria, Antonio; Maietta, Saverio; Martorelli, Massimo; Lanzotti, Antonio; Watts, David C; Ausiello, Pietro

2018-04-24

To assess conceptual designs of dental posts consisting of polyetherimide (PEI) reinforced with carbon (C) and glass (G) glass fibers in endodontically treated anterior teeth. 3D tessellated CAD and geometric models of endodontically treated anterior teeth were generated from Micro-CT scan images. Model C-G/PEI composite posts with different Young's moduli were analyzed by Finite Element (FE) methods post A (57.7GPa), post B (31.6GPa), post C (from 57.7 to 9.0GPa in the coronal-apical direction). A load of 50N was applied at 45° to the longitudinal axis of the tooth, acting on the palatal surface of the crown. The maximum principal stress distribution was determined along the post and at the interface between the post and the surrounding structure. Post C, with Young's modulus decreasing from 57.7 to 9.0GPa in the coronal-apical direction, reduced the maximum principal stress distribution in the restored tooth. Post C gave reduced stress and the most uniform stress distribution with no stress concentration, compared to the other C-G/PEI composite posts. The FE analysis confirmed the ability of the functionally graded post to dissipate stress from the coronal to the apical end. Hence actual (physical) C-G/PEI posts could permit optimization of stress distributions in endodontically treated anterior teeth. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.

Relationship between food habits and tooth erosion occurrence in Malaysian University students.

PubMed

Manaf, Zahara Abdul; Lee, Mei Tee; Ali, Nor Hazirah Muhammad; Samynathan, Selvamary; Jie, Ying Phor; Ismail, Noor Hasnani; Bibiana Hui Ying, Yong; Wei Seng, Yeo; Yahya, Nurul Asyikin

2012-04-01

Tooth erosion is a growing dental problem; however, the role of diet in the aetiology of tooth erosion is unclear. A cross-sectional study was conducted to determine the association between tooth erosion occurrence and the consumption of acidic foods and drinks among undergraduate university students. A total of 150 undergraduate students (33 males and 117 females) aged 19 to 24 years at Universiti Kebangsaan Malaysia participated in this study. The Basic Erosive Wear Examination was used to assess the occurrence of tooth erosion. Information regarding dental hygiene practices, usual dietary habits, and consumption of acidic foods and drinks was obtained through a structured questionnaire. In all, 68% of subjects had tooth erosion. Subjects who reported having received information about healthy eating were less likely to have tooth erosion (χ(2) [1, N = 150] = 7.328, P = 0.007). The frequencies of milk (OR = 0.29, 95% CI = 0.13-0.67) and tea/coffee (adjusted OR = 0.42, 95% CI = 0.19-0.95) consumption were negatively associated with tooth erosion. Dental hygiene practice, the frequency and amount of acidic food and drink intake, and body mass index classification were not significantly associated with the risk of tooth erosion (P > 0.05). A high prevalence of tooth erosion was observed among this group of students. Preventive measures, such as dietary advice and increased consumption of milk at a younger age, may reduce the occurrence of tooth erosion among this age group.

Relationship between Food Habits and Tooth Erosion Occurrence in Malaysian University Students

PubMed Central

Zahara, Abdul Manaf; Mei Tee, Lee; Nor Hazirah, Muhammad Ali; Selvamary, Samynathan; Ying Phor, Jie; Noor Hasnani, Ismail; Bibiana Hui Ying, Yong; Wei Seng, Yeo; Nurul Asyikin, Yahya

2012-01-01

Background: Tooth erosion is a growing dental problem; however, the role of diet in the aetiology of tooth erosion is unclear. A cross-sectional study was conducted to determine the association between tooth erosion occurrence and the consumption of acidic foods and drinks among undergraduate university students. Methods: A total of 150 undergraduate students (33 males and 117 females) aged 19 to 24 years at Universiti Kebangsaan Malaysia participated in this study. The Basic Erosive Wear Examination was used to assess the occurrence of tooth erosion. Information regarding dental hygiene practices, usual dietary habits, and consumption of acidic foods and drinks was obtained through a structured questionnaire. Results: In all, 68% of subjects had tooth erosion. Subjects who reported having received information about healthy eating were less likely to have tooth erosion (χ2 [1, N = 150] = 7.328, P = 0.007). The frequencies of milk (OR = 0.29, 95% CI = 0.13–0.67) and tea/coffee (adjusted OR = 0.42, 95% CI = 0.19–0.95) consumption were negatively associated with tooth erosion. Dental hygiene practice, the frequency and amount of acidic food and drink intake, and body mass index classification were not significantly associated with the risk of tooth erosion (P > 0.05). Conclusion: A high prevalence of tooth erosion was observed among this group of students. Preventive measures, such as dietary advice and increased consumption of milk at a younger age, may reduce the occurrence of tooth erosion among this age group. PMID:22973138

Dental Erosion and Medical Conditions: An Overview of Aetiology, Diagnosis and Management.

PubMed

Paryag, A; Rafeek, R

2014-09-01

Tooth wear or tooth surface loss is a normal physiological process and occurs throughout life but is considered pathological when the degree of destruction is excessive or the rate of loss is rapid, causing functional, aesthetic or sensitivity problems. The importance of tooth wear as a dental problem has been increasingly recognized. The findings of a study in Trinidad indicate that the prevalence of tooth wear in a Trinidadian population is comparable to the United Kingdom (UK) and, indeed, that the level of moderate and severe wear is in fact nearly twice as high. The aetiology of tooth wear is attributed to four causes: erosion, attrition, abrasion and abfraction. Erosion is generally considered to be the most prevalent cause of tooth wear in the UK and Europe. Acids that cause dental erosion originate mainly from the diet or the stomach and to a lesser extent, the environment. Underlying medical problems can contribute to the progress of tooth wear due to erosion and the patient may not be aware of these conditions. Moderate to severe tooth wear poses a significant clinical challenge to dental practitioners and may result in treatment that is more complex and costly to the patient both in terms of finances and time spent in the dental chair. This paper provides an overview of aetiology and diagnosis of tooth wear, in particular tooth wear due to erosion, so that medical and dental practitioners may recognize tooth wear early, institute preventive measures and manage patients appropriately.

Dental Erosion and Medical Conditions An Overview of Aetiology, Diagnosis and Management

PubMed Central

Paryag, A; Rafeek, R

2014-01-01

ABSTRACT Tooth wear or tooth surface loss is a normal physiological process and occurs throughout life but is considered pathological when the degree of destruction is excessive or the rate of loss is rapid, causing functional, aesthetic or sensitivity problems. The importance of tooth wear as a dental problem has been increasingly recognized. The findings of a study in Trinidad indicate that the prevalence of tooth wear in a Trinidadian population is comparable to the United Kingdom (UK) and, indeed, that the level of moderate and severe wear is nearly twice as high. The aetiology of tooth wear is attributed to four causes: erosion, attrition, abrasion and abfraction. Erosion is generally considered to be the most prevalent cause of tooth wear in the UK and Europe. Acids that cause dental erosion originate mainly from the diet or the stomach and, to a lesser extent, the environment. Underlying medical problems can contribute to influence the progress of tooth wear due to erosion and the patient may not be aware of these conditions. Moderate to severe tooth wear poses a significant clinical challenge to dental practitioners and may result in treatment that is more complex and costly to the patient, both in terms of finances and time spent in the dental chair. This paper provides an overview of aetiology and diagnosis of tooth wear, in particular tooth wear due to erosion, so that medical and dental practitioners may recognize tooth wear early, institute preventive measures and manage patients appropriately. PMID:25781289

Pre-existing Periapical Inflammatory Condition Exacerbates Tooth Extraction–induced BRONJ Lesions in Mice

PubMed Central

Song, Minju; Alshaikh, Abdullah; Kim, Terresa; Kim, Sol; Dang, Michelle; Mehrazarin, Shebli; Shin, Ki-Hyuk; Kang, Mo; Park, No-Hee; Kim, Reuben H.

2016-01-01

Introduction Surgical interventions such as tooth extraction increase a chance of developing osteonecrosis of the jaw (ONJ) in patients receiving bisphosphonates (BPs) for treatment of bone-related diseases. Tooth extraction is often performed to eliminate pre-existing pathological inflammatory conditions that make the tooth unsalvageable; however, the role of such conditions on bisphosphonate-related ONJ (BRONJ) development following tooth extraction is not clearly defined. Here, we examined the effects of periapical periodontitis on tooth extraction-induced BRONJ development in mice. Methods Periapical periodontitis was induced by exposing the pulp of the maxillary first molar for 3 weeks in C57/BL6 mice that were intravenously administered with BP. The same tooth was extracted, and after 3 additional weeks, the mice were harvested for histological, histomorphometric, and histochemical staining analyses. Results Pulp exposure induced periapical radiolucency as demonstrated by increased inflammatory cells, TRAP+ osteoclasts, and bone resorption. When BP was administered, pulp exposure did not induce apical bone resorption despite the presence of inflammatory cells and TRAP+ osteoclasts. While tooth extraction alone induced BRONJ lesions, pulp exposure further increased tooth extraction-induced BRONJ development as demonstrated by the presence of more bone necrosis. Conclusion Our study demonstrates that pre-existing pathological inflammatory condition such as periapical periodontitis is a predisposing factor that may exacerbate BRONJ development following tooth extraction. Our study further provides a clinical implication whereby periapical periodontitis should be controlled before performing tooth extraction in BP-users in order to reduce the risk of developing BRONJ. PMID:27637460

Minimizing the extra-oral time in autogeneous tooth transplantation: use of computer-aided rapid prototyping (CARP) as a duplicate model tooth.

PubMed

Lee, Seung-Jong; Kim, Euiseong

2012-08-01

The maintenance of the healthy periodontal ligament cells of the root surface of donor tooth and intimate surface contact between the donor tooth and the recipient bone are the key factors for successful tooth transplantation. In order to achieve these purposes, a duplicated donor tooth model can be utilized to reduce the extra-oral time using the computer-aided rapid prototyping (CARP) technique. Briefly, a three-dimensional digital imaging and communication in medicine (DICOM) image with the real dimensions of the donor tooth was obtained from a computed tomography (CT), and a life-sized resin tooth model was fabricated. Dimensional errors between real tooth, 3D CT image model and CARP model were calculated. And extra-oral time was recorded during the autotransplantation of the teeth. The average extra-oral time was 7 min 25 sec with the range of immediate to 25 min in cases which extra-oral root canal treatments were not performed while it was 9 min 15 sec when extra-oral root canal treatments were performed. The average radiographic distance between the root surface and the alveolar bone was 1.17 mm and 1.35 mm at mesial cervix and apex; they were 0.98 mm and 1.26 mm at the distal cervix and apex. When the dimensional errors between real tooth, 3D CT image model and CARP model were measured in cadavers, the average of absolute error was 0.291 mm between real teeth and CARP model. These data indicate that CARP may be of value in minimizing the extra-oral time and the gap between the donor tooth and the recipient alveolar bone in tooth transplantation.

Tooth color measurement using Chroma Meter: techniques, advantages, and disadvantages.

PubMed

Li, Yiming

2003-01-01

Tooth whitening has become a popular and routine dental procedure, and its efficacy and safety have been well documented. However, the measurement of tooth color, particularly in the evaluation of the efficacy of a system intended to enhance tooth whiteness, remains a challenge. One of the instruments used for assessing tooth color in clinical whitening studies is the Minolta Chroma Meter CR-321 (Minolta Corporation USA, Ramsey, NJ, USA). This article describes the instrument and discusses various measuring procedures and the Chroma Meter's advantages, limitations, and disadvantages. The available information indicates that, although Minolta Chroma Meter CR-321 provides quantitative and objective measurements of tooth color, it can be tedious to use with a custom alignment device. The Chroma Meter data are inconsistent with the commonly used visual instruments such as Vitapan Classical Shade Guide (Vita Zahnfabrik, Bad Säckingen, Germany), although in many cases the general trends are similar. It is also questionable whether the small area measured adequately represents the color of the whole tooth. A more critical challenge is the lack of methods for interpreting the Chroma Meter data regarding tooth color change in studies evaluating the efficacy of whitening systems. Consequently, at present the Chroma Meter data alone do not appear to be adequate for determining tooth color change in whitening research, although the quantitative measurements may be useful as supplemental or supportive data. Research is needed to develop and improve the instrument and technique for quantitative measurement of tooth color and interpretation of the data for evaluating tooth color change. This paper will help readers to understand the advantages and limitations of the Minolta Chroma Meter used for evaluating the efficacy of tooth-whitening systems so that proper judgment can be made in the interpretation of the results of clinical studies.

Impact of bisphosphonate drug burden in alveolar bone during orthodontic tooth movement in a rat model: a pilot study.

PubMed

Kaipatur, Neelambar R; Wu, Yuchin; Adeeb, Samer; Stevenson, Thomas R; Major, Paul W; Doschak, Michael R

2013-10-01

The aim of this pilot study was to investigate the effect of long-term bisphosphonate drug use (bone burden) on orthodontic tooth movement in a rat model. Sprague Dawley rats were used for orthodontic protraction of the maxillary first molars with nickel-titanium coil springs and temporary anchorage devices as anchorage. Four groups of 5 rats each were included in the study; the first 2 groups were dosed with alendronate or a vehicle during concurrent orthodontic tooth movement. The third and fourth groups were pretreated for 3 months with alendronate or vehicle injections, and bisphosphonate drug treatment was discontinued before orthodontic tooth movement. Tooth movement measurements were obtained at 0, 4, and 8 weeks using high-resolution in-vivo microcomputed tomography, and the tissues were analyzed with histology and dynamic labeling of bone turnover. Appreciable tooth movement was achieved during the 8-week duration of this study with nickel-titanium coil springs and temporary anchorage devices. Both bisphosphonate treatment groups exhibited reduced tooth movement compared with the vehicle-dosed controls with a tendency toward more severe reduction in the bisphosphonate predosed group. Concurrent dosing of the bisphosphonate drug resulted in 56% and 65% reductions in tooth protraction at the 4-week and 8-week times, respectively. The impact of bisphosphonate bone burden in retarding tooth movement was even greater, with 77% and 86% reductions in tooth movement at 4 and 8 weeks, respectively. In this study, we used a robust rat model of orthodontic tooth movement with temporary anchorage devices. It has provided evidence that the bone burden of previous bisphosphonate use will significantly inhibit orthodontic tooth movement. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Endodontic Treatment of an Anomalous Anterior Tooth with the Aid of a 3-dimensional Printed Physical Tooth Model.

PubMed

Byun, Chanhee; Kim, Changhwan; Cho, Seungryong; Baek, Seung Hoon; Kim, Gyutae; Kim, Sahng G; Kim, Sun-Young

2015-06-01

Endodontic treatment of tooth formation anomalies is a challenge to clinicians and as such requires a complete understanding of the aberrant root canal anatomy followed by careful root canal disinfection and obturation. Here, we report the use of a 3-dimensional (3D) printed physical tooth model including internal root canal structures for the endodontic treatment of a challenging tooth anomaly. A 12-year-old boy was referred for endodontic treatment of tooth #8. The tooth showed class II mobility with swelling and a sinus tract in the buccal mucosa and periapical radiolucency. The tooth presented a very narrow structure between the crown and root by distal concavity and a severely dilacerated root. Moreover, a perforation site with bleeding and another ditching site were identified around the cervical area in the access cavity. A translucent physical tooth model carrying the information on internal root canal structures was built through a 3-step process: data acquisition by cone-beam computed tomographic scanning, virtual modeling by image processing, and manufacturing by 3D printing. A custom-made guide jig was then fabricated to achieve a safe and precise working path to the root canal. Endodontic procedures including access cavity preparation were performed using the physical tooth model and the guide jig. At the 7-month follow-up, the endodontically treated tooth showed complete periapical healing with no clinical signs and symptoms. This case report describes a novel method of endodontic treatment of an anomalous maxillary central incisor with the aid of a physical tooth model and a custom-made guide jig via 3D printing technique. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Common developmental pathways link tooth shape to regeneration

PubMed Central

Fraser, Gareth J.; Bloomquist, Ryan F.; Streelman, J. Todd

2013-01-01

In many non-mammalian vertebrates, adult dentitions result from cyclical rounds of tooth regeneration wherein simple unicuspid teeth are replaced by more complex forms. Therefore and by contrast to mammalian models, the numerical majority of vertebrate teeth develop shape during the process of replacement. Here, we exploit the dental diversity of Lake Malawi cichlid fishes to ask how vertebrates generally replace their dentition and in turn how this process acts to influence resulting tooth morphologies. First, we used immunohistochemistry to chart organogenesis of continually replacing cichlid teeth and discovered an epithelial down-growth that initiates the replacement cycle via a labial proliferation bias. Next, we identified sets of co-expressed genes from common pathways active during de novo, lifelong tooth replacement and tooth morphogenesis. Of note, we found two distinct epithelial cell populations, expressing markers of dental competence and cell potency, which may be responsible for tooth regeneration. Related gene sets were simultaneously active in putative signaling centers associated with the differentiation of replacement teeth with complex shapes. Finally, we manipulated targeted pathways (BMP, FGF, Hh, Notch, Wnt/β-catenin) in vivo with small molecules and demonstrated dose-dependent effects on both tooth replacement and tooth shape. Our data suggest that the processes of tooth regeneration and tooth shape morphogenesis are integrated via a common set of molecular signals. This linkage has subsequently been lost or decoupled in mammalian dentitions where complex tooth shapes develop in first generation dentitions that lack the capacity for lifelong replacement. Our dissection of the molecular mechanics of vertebrate tooth replacement coupled to complex shape pinpoints aspects of odontogenesis that might be re-evolved in the lab to solve problems in regenerative dentistry. PMID:23422830

Hedgehog signaling is required at multiple stages of zebrafish tooth development.

PubMed

Jackman, William R; Yoo, James J; Stock, David W

2010-11-30

The accessibility of the developing zebrafish pharyngeal dentition makes it an advantageous system in which to study many aspects of tooth development from early initiation to late morphogenesis. In mammals, hedgehog signaling is known to be essential for multiple stages of odontogenesis; however, potential roles for the pathway during initiation of tooth development or in later morphogenesis are incompletely understood. We have identified mRNA expression of the hedgehog ligands shha and the receptors ptc1 and ptc2 during zebrafish pharyngeal tooth development. We looked for, but did not detect, tooth germ expression of the other known zebrafish hedgehog ligands shhb, dhh, ihha, or ihhb, suggesting that as in mammals, only Shh participates in zebrafish tooth development. Supporting this idea, we found that morphological and gene expression evidence of tooth initiation is eliminated in shha mutant embryos, and that morpholino antisense oligonucleotide knockdown of shha, but not shhb, function prevents mature tooth formation. Hedgehog pathway inhibition with the antagonist compound cyclopamine affected tooth formation at each stage in which we applied it: arresting development at early stages and disrupting mature tooth morphology when applied later. These results suggest that hedgehog signaling is required continuously during odontogenesis. In contrast, over-expression of shha had no effect on the developing dentition, possibly because shha is normally extensively expressed in the zebrafish pharyngeal region. We have identified previously unknown requirements for hedgehog signaling for early tooth initiation and later morphogenesis. The similarity of our results with data from mouse and other vertebrates suggests that despite gene duplication and changes in the location of where teeth form, the roles of hedgehog signaling in tooth development have been largely conserved during evolution.

Cold-Water Immersion for Hyperthermic Humans Wearing American Football Uniforms

PubMed Central

Miller, Kevin C.; Swartz, Erik E.; Long, Blaine C.

2015-01-01

Context Current treatment recommendations for American football players with exertional heatstroke are to remove clothing and equipment and immerse the body in cold water. It is unknown if wearing a full American football uniform during cold-water immersion (CWI) impairs rectal temperature (Trec) cooling or exacerbates hypothermic afterdrop. Objective To determine the time to cool Trec from 39.5°C to 38.0°C while participants wore a full American football uniform or control uniform during CWI and to determine the uniform's effect on Trec recovery postimmersion. Design Crossover study. Setting Laboratory. Patients or Other Participants A total of 18 hydrated, physically active, unacclimated men (age = 22 ± 3 years, height = 178.8 ± 6.8 cm, mass = 82.3 ± 12.6 kg, body fat = 13% ± 4%, body surface area = 2.0 ± 0.2 m2). Intervention(s) Participants wore the control uniform (undergarments, shorts, crew socks, tennis shoes) or full uniform (control plus T-shirt; tennis shoes; jersey; game pants; padding over knees, thighs, and tailbone; helmet; and shoulder pads). They exercised (temperature approximately 40°C, relative humidity approximately 35%) until Trec reached 39.5°C. They removed their T-shirts and shoes and were then immersed in water (approximately 10°C) while wearing each uniform configuration; time to cool Trec to 38.0°C (in minutes) was recorded. We measured Trec (°C) every 5 minutes for 30 minutes after immersion. Main Outcome Measure(s) Time to cool from 39.5°C to 38.0°C and Trec. Results The Trec cooled to 38.0°C in 6.19 ± 2.02 minutes in full uniform and 8.49 ± 4.78 minutes in control uniform (t17 = −2.1, P = .03; effect size = 0.48) corresponding to cooling rates of 0.28°C·min−1 ± 0.12°C·min−1 in full uniform and 0.23°C·min−1 ± 0.11°C·min−1 in control uniform (t17 = 1.6, P = .07, effect size = 0.44). The Trec postimmersion recovery did not differ between conditions over time (F1,17 = 0.6, P = .59). Conclusions We speculate that higher skin temperatures before CWI, less shivering, and greater conductive cooling explained the faster cooling in full uniform. Cooling rates were considered ideal when the full uniform was worn during CWI, and wearing the full uniform did not cause a greater postimmersion hypothermic afterdrop. Clinicians may immerse football athletes with hyperthermia wearing a full uniform without concern for negatively affecting body-core cooling. PMID:26090706

Paleobiology: A Tooth for a Tooth.

PubMed

Johanson, Zerina

2017-02-06

Many vertebrates replace teeth through shedding of the functional tooth. New analyses of a fossil fish demonstrate that shedding involved tooth resorption, a primitive feature in bony fishes, but absent in sharks and their relatives. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Ontogenetic Tooth Reduction in Stenopterygius quadriscissus (Reptilia: Ichthyosauria): Negative Allometry, Changes in Growth Rate, and Early Senescence of the Dental Lamina

PubMed Central

Dick, Daniel G.; Maxwell, Erin E.

2015-01-01

We explore the functional, developmental, and evolutionary processes which are argued to produce tooth reduction in the extinct marine reptile Stenopterygius quadriscissus (Reptilia: Ichthyosauria). We analyze the relationship between mandible growth and tooth size, shape, and count, to establish an ontogenetic trend. The pattern in S. quadriscissus is consistent with hypotheses of tooth size reduction by neutral selection, and this unusual morphology (a functionally edentulous rostrum) was produced by a series of different evolutionary developmental changes that are known for other taxa showing tooth reduction and loss. Specifically, this species evolved functional edentulism by evolutionary changes in the growth allometry of the dentition and by altering growth rates through ontogeny. This observation supports previous hypotheses that S. quadriscissus underwent ontogenetic tooth reduction. Tooth reduction in S. quadriscissus may be caused by unique selective pressures resulting from prey choice and feeding behavior, expanding our current understanding of the mechanisms producing tooth reduction. PMID:26579712

Ontogenetic Tooth Reduction in Stenopterygius quadriscissus (Reptilia: Ichthyosauria): Negative Allometry, Changes in Growth Rate, and Early Senescence of the Dental Lamina.

PubMed

Dick, Daniel G; Maxwell, Erin E

2015-01-01

We explore the functional, developmental, and evolutionary processes which are argued to produce tooth reduction in the extinct marine reptile Stenopterygius quadriscissus (Reptilia: Ichthyosauria). We analyze the relationship between mandible growth and tooth size, shape, and count, to establish an ontogenetic trend. The pattern in S. quadriscissus is consistent with hypotheses of tooth size reduction by neutral selection, and this unusual morphology (a functionally edentulous rostrum) was produced by a series of different evolutionary developmental changes that are known for other taxa showing tooth reduction and loss. Specifically, this species evolved functional edentulism by evolutionary changes in the growth allometry of the dentition and by altering growth rates through ontogeny. This observation supports previous hypotheses that S. quadriscissus underwent ontogenetic tooth reduction. Tooth reduction in S. quadriscissus may be caused by unique selective pressures resulting from prey choice and feeding behavior, expanding our current understanding of the mechanisms producing tooth reduction.

Tooth shade measurements under standard and nonstandard illumination and their agreement with skin color.

PubMed

Al-Dwairi, Ziad; Shaweesh, Ashraf; Kamkarfar, Sohrab; Kamkarfar, Shahrzad; Borzabadi-Farahani, Ali; Lynch, Edward

2014-01-01

The purpose of this study was to examine the relationship between skin color (shade) and tooth shade under standard and nonstandard illumination sources. Four hundred Jordanian participants (200 males, 200 females, 20 to 50 years of age) were studied. Skin colors were assessed and categorized using the L'Oreal and Revlon foundation shade guides (light, medium, dark). The Vita Pan Classical Shade Guide (VPCSG; Vident) and digital Vita EasyShade Intraoral Dental Spectrophotometer (VESIDS; Vident) were used to select shades in the middle thirds of maxillary central incisors; tooth shades were classified into four categories (highest, high, medium, low). Significant gender differences were observed for skin colors (P = .000) and tooth shade guide systems (P = .001 and .050 for VPCSG and VESIDS, respectively). The observed agreement was 100% and 93% for skin and tooth shade guides, respectively. The corresponding kappa statistic values were 1.00 and 0.79, respectively (substantial agreement, P < .001). The observed agreement between skin color and tooth shades (VPCSG and VESIDS) was approximately 50%. The digital tooth shade guide system can be a satisfactory substitute for classical tooth shade guides and clinical shade matching. There was only moderate agreement between skin color and tooth shade.

Innovative Design and Performance Evaluation of Bionic Imprinting Toothed Wheel.

PubMed

Zhang, Zhihong; Wang, Xiaoyang; Tong, Jin; Stephen, Carr

2018-01-01

A highly efficient soil-burrowing dung beetle possesses an intricate outer contour curve on its foreleg end-tooth. This study was carried out based on evidence that this special outer contour curve has the potential of reducing soil penetration resistance and could enhance soil-burrowing efficiency. A toothed wheel is a typical agricultural implement for soil imprinting, to increase its working efficiency; the approach of the bionic geometrical structure was utilized to optimize the innovative shape of imprinting toothed wheel. Characteristics in the dung beetle's foreleg end-tooth were extracted and studied by the edge detection technique. Then, this special outer contour curve was modeled by a nine-order polynomial function and used for the innovative design of imprinting the tooth's cutting edge. Both the conventional and bionic teeth were manufactured, and traction tests in a soil bin were conducted. Taking required draft force and volume of imprinted microbasin as the evaluating indexes, operating efficiency and quality of different toothed wheels were compared and investigated. Results indicate that compared with the conventional toothed wheel, a bionic toothed wheel possesses a better forward resistance reduction property against soil and, meanwhile, can enhance the quality of soil imprinting by increasing the volume of the created micro-basin.

3D Simulation Modeling of the Tooth Wear Process.

PubMed

Dai, Ning; Hu, Jian; Liu, Hao

2015-01-01

Severe tooth wear is the most common non-caries dental disease, and it can seriously affect oral health. Studying the tooth wear process is time-consuming and difficult, and technological tools are frequently lacking. This paper presents a novel method of digital simulation modeling that represents a new way to study tooth wear. First, a feature extraction algorithm is used to obtain anatomical feature points of the tooth without attrition. Second, after the alignment of non-attrition areas, the initial homogeneous surface is generated by means of the RBF (Radial Basic Function) implicit surface and then deformed to the final homogeneous by the contraction and bounding algorithm. Finally, the method of bilinear interpolation based on Laplacian coordinates between tooth with attrition and without attrition is used to inversely reconstruct the sequence of changes of the 3D tooth morphology during gradual tooth wear process. This method can also be used to generate a process simulation of nonlinear tooth wear by means of fitting an attrition curve to the statistical data of attrition index in a certain region. The effectiveness and efficiency of the attrition simulation algorithm are verified through experimental simulation.

3D Simulation Modeling of the Tooth Wear Process

PubMed Central

Dai, Ning; Hu, Jian; Liu, Hao

2015-01-01

Severe tooth wear is the most common non-caries dental disease, and it can seriously affect oral health. Studying the tooth wear process is time-consuming and difficult, and technological tools are frequently lacking. This paper presents a novel method of digital simulation modeling that represents a new way to study tooth wear. First, a feature extraction algorithm is used to obtain anatomical feature points of the tooth without attrition. Second, after the alignment of non-attrition areas, the initial homogeneous surface is generated by means of the RBF (Radial Basic Function) implicit surface and then deformed to the final homogeneous by the contraction and bounding algorithm. Finally, the method of bilinear interpolation based on Laplacian coordinates between tooth with attrition and without attrition is used to inversely reconstruct the sequence of changes of the 3D tooth morphology during gradual tooth wear process. This method can also be used to generate a process simulation of nonlinear tooth wear by means of fitting an attrition curve to the statistical data of attrition index in a certain region. The effectiveness and efficiency of the attrition simulation algorithm are verified through experimental simulation. PMID:26241942

SU-E-I-91: Reproducibility in Prescribed Dose in AEC CT Scans Due to Table Height, Patient Size, and Localizer Acquisition Order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winslow, J; Hurwitz, L; Christianson, O

2014-06-01

Purpose: In CT scanners, the automatic exposure control (AEC) tube current prescription depends on the acquired prescan localizer image(s). The purpose of this study was to quantify the effect that table height, patient size, and localizer acquisition order may have on the reproducibility in prescribed dose. Methods: Three phantoms were used for this study: the Mercury Phantom (comprises three tapered and four uniform regions of polyethylene 16, 23, 30, and 37 cm in diameter), acrylic sheets, and an adult anthropomorphic phantom. Phantoms were positioned per clinical protocol by our chief CT technologist or broader symmetry. Using a GE Discovery CT750HDmore » scanner, a lateral (LAT) and posterior-anterior (PA) localizer was acquired for each phantom at different table heights. AEC scan acquisitions were prescribed for each combination of phantom, localizer orientation, and table height; the displayed volume CTDI was recorded for each. Results were analyzed versus table height. Results: For the two largest Mercury Phantom section scans based on the PA localizer, the percent change in volume CTDI from ideal were at least 20% lower and 35% greater for table heights 4 cm above and 4 cm below proper centering, respectively. For scans based on the LAT localizer, the percent change in volume CTDI from ideal were no greater than 12% different for 4 cm differences in table height. The properly centered PA and LAT localizer-based volume CTDI values were within 13% of each other. Conclusion: Since uncertainty in vertical patient positioning is inherently greater than lateral positioning and because the variability in dose exceeds any dose penalties incurred, the LAT localizer should be used to precisely and reproducibly deliver the intended amount of radiation prescribed by CT protocols. CT protocols can be adjusted to minimize the expected change in average patient dose.« less

Simulation of Flow Fluid in the BOF Steelmaking Process

NASA Astrophysics Data System (ADS)

Lv, Ming; Zhu, Rong; Guo, Ya-Guang; Wang, Yong-Wei

2013-12-01

The basic oxygen furnace (BOF) smelting process consists of different chemical reactions among oxygen, slag, and molten steel, which engenders a vigorous stirring process to promote slagging, dephosphorization, decarbonization, heating of molten steel, and homogenization of steel composition and temperature. Therefore, the oxygen flow rate, lance height, and slag thickness vary during the smelting process. This simulation demonstrated a three-dimensional mathematical model for a 100 t converter applying four-hole supersonic oxygen lance and simulated the effect of oxygen flow rate, lance height, and slag thickness on the flow of molten bath. It is found that as the oxygen flow rate increases, the impact area and depth increases, which increases the flow speed in the molten bath and decreases the area of dead zone. Low oxygen lance height benefits the increase of impact depth and accelerates the flow speed of liquid steel on the surface of the bath, while high oxygen lance height benefits the increase of impact area, thereafter enhances the uniform distribution of radial velocity in the molten steel and increases the flow velocity of molten steel at the bottom of furnace hearth. As the slag thickness increases, the diameter of impinging cavity on the slag and steel surface decreases. The radial velocity of liquid steel in the molten bath is well distributed when the jet flow impact on the slag layer increases.

Inferring Discharge at River Mouths from Water Surface Height Measurements

NASA Astrophysics Data System (ADS)

Branch, R.; Horner-Devine, A.; Chickadel, C. C.

2016-02-01

Numerical model results suggest that a relationship exists between river discharge and surface height anomalies near the mouth of rivers, which presents an opportunity to use satellite elevation data to measure discharge remotely. Here we investigate whether such a relationship can be observed in the field using airborne lidar data at the mouth of the Columbia River. Airborne Lidar data were used because current NASA altimeter data does not have high enough spatial resolution to image surface elevation along a river. NASA's Surface Water and Ocean Topography, SWOT, sensor is planned to have a spatial resolution of less than 100 m and maximum height precision of 1 cm. The magnitude and temporal duration of the elevation signal found in the lidar data will be used to determine if SWOT will have the resolution and precision capabilities to measure discharge from space. Lidar data were acquired during a range of tidal conditions and discharge rates from May through September of 2013. Our results suggest that there is a measurable surface height anomaly at the river mouth during part of the tidal cycle. A 0.7 m surface depression was found during ebb tide and a uniform surface tilt was found at slack tide. The variation of the anomaly over the tidal period presents a challenge for decoupling the tidal component from that due to the discharge.

Consequences of tooth loss: 2. Dentist considerations--restorative problems and implications.

PubMed

Craddock, Helen L

2010-01-01

Partial tooth loss is much less well tolerated by patients than was previously the case and, on occasions, when extraction is inevitable, they may seek prosthetic replacement. This paper explores some of the consequences of tooth loss that may cause difficulties in tooth replacement, particularly if replacement is delayed for some time. An awareness of potential difficulties, particularly with posterior tooth replacement, will allow clinicians to make treatment decisions in the light of current evidence.

Detecting gear tooth fracture in a high contact ratio face gear mesh

NASA Technical Reports Server (NTRS)

Zakrajsek, James J.; Handschuh, Robert F.; Lewicki, David G.; Decker, Harry J.

1995-01-01

This paper summarized the results of a study in which three different vibration diagnostic methods were used to detect gear tooth fracture in a high contact ratio face gear mesh. The NASA spiral bevel gear fatigue test rig was used to produce unseeded fault, natural failures of four face gear specimens. During the fatigue tests, which were run to determine load capacity and primary failure mechanisms for face gears, vibration signals were monitored and recorded for gear diagnostic purposes. Gear tooth bending fatigue and surface pitting were the primary failure modes found in the tests. The damage ranged from partial tooth fracture on a single tooth in one test to heavy wear, severe pitting, and complete tooth fracture of several teeth on another test. Three gear fault detection techniques, FM4, NA4*, and NB4, were applied to the experimental data. These methods use the signal average in both the time and frequency domain. Method NA4* was able to conclusively detect the gear tooth fractures in three out of the four fatigue tests, along with gear tooth surface pitting and heavy wear. For multiple tooth fractures, all of the methods gave a clear indication of the damage. It was also found that due to the high contact ratio of the face gear mesh, single tooth fractures did not significantly affect the vibration signal, making this type of failure difficult to detect.

Premolar and molar rotation in wild Japanese serow populations on Honshu Island, Japan.

PubMed

Natsume, Asuka; Koyasu, Kazuhiro; Oda, Sen-ichi; Nakagaki, Haruo; Hanamura, Hajime

2006-11-01

The skulls of 1195 Japanese serow (Capricornis crispus) from six geographically distinct populations were examined for tooth rotation. Our objectives were to determine tooth rotation patterns in Japanese serows, investigate geographical variation in tooth rotation and examine whether space limitations in the jaw accounted for variations. We then sought to explain the origin of tooth rotation in the Japanese serow. Rotated teeth were found in 131 specimens (62 males, 57 females and 12 unknown gender), with no statistically significant difference between males and females (chi(2)=0.03, P=0.86, d.f.=1). Among the six populations, the frequency of tooth rotation varied from 3.7-32.1% (average 11.0%). Most tooth rotation occurred in the upper third and fourth premolars. The lingual cusp of anomalous teeth was rotated 30 degrees -90 degrees mesially or distally from the buccolingual tooth axis, and the rotation direction differed among populations. However, we found no difference in skull or tooth morphology between normal individuals and those with tooth rotation. Therefore, hereditary factors may be involved in Japanese serow tooth rotation. We concluded that genetic differentiation occurred in the past among local Japanese serow populations isolated in mountainous habitats. Gene frequencies were likely subject to random drift, especially during possible population bottlenecks, when genetic factors could most strongly affect the direction of rotation.

A new digitized reverse correction method for hypoid gears based on a one-dimensional probe

NASA Astrophysics Data System (ADS)

Li, Tianxing; Li, Jubo; Deng, Xiaozhong; Yang, Jianjun; Li, Genggeng; Ma, Wensuo

2017-12-01

In order to improve the tooth surface geometric accuracy and transmission quality of hypoid gears, a new digitized reverse correction method is proposed based on the measurement data from a one-dimensional probe. The minimization of tooth surface geometrical deviations is realized from the perspective of mathematical analysis and reverse engineering. Combining the analysis of complex tooth surface generation principles and the measurement mechanism of one-dimensional probes, the mathematical relationship between the theoretical designed tooth surface, the actual machined tooth surface and the deviation tooth surface is established, the mapping relation between machine-tool settings and tooth surface deviations is derived, and the essential connection between the accurate calculation of tooth surface deviations and the reverse correction method of machine-tool settings is revealed. Furthermore, a reverse correction model of machine-tool settings is built, a reverse correction strategy is planned, and the minimization of tooth surface deviations is achieved by means of the method of numerical iterative reverse solution. On this basis, a digitized reverse correction system for hypoid gears is developed by the organic combination of numerical control generation, accurate measurement, computer numerical processing, and digitized correction. Finally, the correctness and practicability of the digitized reverse correction method are proved through a reverse correction experiment. The experimental results show that the tooth surface geometric deviations meet the engineering requirements after two trial cuts and one correction.

[Clinical evaluation of influence of aspirin on post-operative bleeding after tooth extraction in the elderly].

PubMed

Wang, Wen-ying; Cui, Nian-hui; Wang, En-bo; Zhang, Wei

2013-05-01

To investigate the feasibility of continuation of aspirin before tooth extraction in the elderly. The patients enrolled in this study were the elderly requiring a single non-impacted tooth extraction. 300 elderly outpatients used lidocaine local infiltration anesthesia, 200 patients without using aspirin before tooth extraction served as control group I, 100 patients with prolong use of aspirin before tooth extraction as observation group I. 300 elderly outpatients used compound articaine local infiltration anesthesia, 200 patients without using aspirin before tooth extraction served as control group II, 100 patients with prolong use of aspirin before tooth extraction as observation group II.Bleedings at 5, 10, 30 min, 24 h after tooth extraction were observed and the relationship between postoperative bleeding and intake of aspirin was analyzed. There was no significant difference at 5, 10, 30 min, 24 h in postoperative bleeding after extraction between control group I and observation group. The incidence of bleeding of observation group II after tooth extraction at 5 min was higher than that of control group II and there was no significant difference at 10, 30 min, 24 h between the two groups. Continuation of aspirin have no influence on postoperative bleeding. Therefore we suggest that there was no indication to discontinue aspirin for the elderly before a single non-impacted tooth extraction.

Formation of a successional dental lamina in the zebrafish (Danio rerio): support for a local control of replacement tooth initiation.

PubMed

Huysseune, Ann

2006-01-01

In order to test whether the formation of a replacement tooth bud in a continuously replacing dentition is linked to the functional state of the tooth predecessor, I examined the timing of development of replacement teeth with respect to their functional predecessors in the pharyngeal dentition of the zebrafish. Observations based on serial semithin sections of ten specimens, ranging in age from four week old juveniles to adults, indicate that (i) a replacement tooth germ develops at the distal end of an epithelial structure, called the successional dental lamina, budding off from the crypt epithelium surrounding the erupted part of a functional tooth; (ii) there appears to be a developmental link between the eruption of a tooth and the formation of a successional dental lamina and (iii) there can be a time difference between successional lamina formation and initiation of the new tooth germ, i.e., the successional dental lamina can remain quiescent for some time. The data suggest that the formation of a successional lamina and the differentiation of a replacement tooth germ from this lamina, are two distinct phases of a process and possibly under a different control. The strong spatio-temporal coincidence of eruption of a tooth and development of a successional dental lamina is seen as evidence for a local control over tooth replacement.

Evidence for Nonuniform Heating of Coronal Loops Inferred from Multithread Modeling of TRACE Data

NASA Astrophysics Data System (ADS)

Aschwanden, Markus J.; Nightingale, Richard W.; Alexander, David

2000-10-01

The temperature Te(s) and density structure ne(s) of active region loops in EUV observed with TRACE is modeled with a multithread model, synthesized from the summed emission of many loop threads that have a distribution of maximum temperatures and that satisfy the steady state Rosner-Tucker-Vaiana (RTV) scaling law, modified by Serio et al. for gravitational stratification (called RTVSp in the following). In a recent Letter, Reale & Peres demonstrated that this method can explain the almost isothermal appearance of TRACE loops (observed by Lenz et al.) as derived from the filter-ratio method. From model-fitting of the 171 and 195 Å fluxes of 41 loops, which have loop half-lengths in the range of L=4-320 Mm, we find that (1) the EUV loops consist of near-isothermal loop threads with substantially smaller temperature gradients than are predicted by the RTVSp model; (2) the loop base pressure, p0~0.3+/-0.1 dynes cm-2, is independent of the loop length L, and it agrees with the RTVSp model for the shortest loops but exceeds the RTVSp model up to a factor of 35 for the largest loops; and (3) the pressure scale height is consistent with hydrostatic equilibrium for the shortest loops but exceeds the temperature scale height up to a factor of ~3 for the largest loops. The data indicate that cool EUV loops in the temperature range of Te~0.8-1.6 MK cannot be explained with the static steady state RTVSp model in terms of uniform heating but are fully consistent with Serio's model in the case of nonuniform heating (RTVSph), with heating scale heights in the range of sH=17+/-6 Mm. This heating function provides almost uniform heating for small loops (L<~20 Mm), but restricts heating to the footpoints of large loops (L~50-300 Mm).

Assessment of codes, by-laws and regulations relating to air wells in building design

NASA Astrophysics Data System (ADS)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

[Esthetic analysis on immediate single-tooth implant restoration in anterior maxilla].

PubMed

Li, Shao-wei; Wang, Guo-shi; Sha, Yan-zhi

2015-10-01

To evaluate the esthetic outcomes of immediate single-tooth implant restoration in anterior maxilla with the pink esthetic score (PES). Nine patients were treated with 9 Straumann implants by immediate single-tooth implant restoration in anterior maxilla. Assessment of PES after crown placement at 1 week (baseline) and 6 months after implantation was conducted. Statistical analysis was performed using SPSS 16.0 software package. Nine implants achieved a retention rate of 100%. PES for single-tooth implant was 10.33 ± 1.50 at 1 week and 11.44 ± 0.88 at 6 months after crown placement. The difference was significant(P=0.021). This study indicates that immediate single-tooth implant restoration in anterior maxilla is predictable. Immediate single-tooth implantation can result in good clinical esthetic results in most patients with single-tooth missing in anterior maxilla.

Deciduous tooth chronology in the mandible of the domestic pig.

PubMed

Bivin, W S; McClure, R C

1976-01-01

Fetuses of known age, collected from 20 days' gestation to term, were used to characterize the chronology of deciduous tooth development within the right mandible of swine. Tooth development was first observed at 32 days' embryonic development, with the differentiation of the deciduous third molar. Bud stages for the remaining deciduous teeth differentiated within the period of 32 to 38 days of embryonic development. Although the initial histological appearance of these teeth covered a short period of time, it was apparent that each tooth continued to develop at its own rate. The deciduous second incisor and first molar reached a stage of enamel formation by the 80th and 86th day of fetal development. This is a much later stage than previously recorded for beginning enamel formation. The stages of tooth development and enamel formation for each tooth are summarized. A previous report on the distribution of the dental lamina and deciduous tooth development in the mandible of the domestic pig combined with the information presented in this report on tooth chronology provide much of the information required for future studies using the domestic pig in dental research. A fetus observed at the 74th day of development demonstrated a tooth bud for the deciduous first premolar. The development of this tooth was followed closely throughout the remainder of fetal development with the cap stage representing its most definitive form at 110 days' development. The suggested deciduous origin for this tooth could result in a reevaluation of the nomenclature for the dental formula of swine.

Regenerative Endodontic Treatment with Orthodontic Treatment in a Tooth with Dens Evaginatus: A Case Report with a 4-year Follow-up.

PubMed

Natera, Marianella; Mukherjee, Padma M

2018-06-01

Dens evaginatus is a developmental tooth anomaly in which an extra cusp or tubercle protrudes on the occlusal surface of the tooth along with some pulpal tissue. Because of the fragile nature of the protrusion, these teeth are often at risk of pulpal exposure. When this occurs in an immature tooth, regenerative endodontic treatment may be a good treatment approach to promote root formation. There is limited literature that documents the occurrence of orthodontic treatment in teeth that have undergone regenerative endodontic therapy using triple antibiotic paste. Here we present a case of an immature premolar tooth with dens evaginatus that was diagnosed with pulp necrosis and chronic apical abscess. The tooth was treated with regenerative endodontic treatment; after which, the patient received orthodontic treatment with fixed appliances for 2 years. The tooth responded favorably to the regenerative endodontic treatment and orthodontic tooth movement. Clinically and radiographically, all the follow-up examinations revealed an asymptomatic tooth with evidence of periapical healing with stunted root development. The tooth remained asymptomatic even after 4 years. The regenerative endodontic procedure (REP) was successful in treating an immature permanent premolar with pulp necrosis and apical periodontitis with dens evaginatus. In this case, the tooth treated with an REP responded to orthodontic treatment similar to the nonendodontically treated teeth. Further studies are recommended to clarify the precise effects of orthodontic treatment on teeth treated with an REP. Copyright © 2018 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Experience of racism and tooth brushing among pregnant Aboriginal Australians: exploring psychosocial mediators.

PubMed

Ben, J; Jamieson, L M; Priest, N; Parker, E J; Roberts-Thomson, K F; Lawrence, H P; Broughton, J; Paradies, Y

2014-09-01

Despite burgeoning evidence regarding the pathways by which experiences of racism influence health outcomes, little attention has been paid to the relationship between racism and oral health-related behaviours in particular. We hypothesised that self-reported racism was associated with tooth brushing, and that this association was mediated by perceived stress and sense of control and moderated by social support. Data from 365 pregnant Aboriginal Australian women were used to evaluate tooth brushing behaviour, sociodemographic factors, psychosocial factors, general health, risk behaviours and racism exposure. Bivariate associations were explored and hierarchical logistic regression models estimated odds ratios (OR) and 95% confidence intervals (CI) for tooth brushing. Perceived stress and sense of control were examined as mediators of the association between self-reported racism and tooth brushing using binary mediation with bootstrapping. High levels of self-reported racism persisted as a risk indicator for tooth brushing (OR 0.51, 95%CI 0.27,0.98) after controlling for significant covariates. Perceived stress mediated the relationship between self-reported racism and tooth brushing: the direct effect of racism on tooth brushing was attenuated, and the indirect effect on tooth brushing was significant (beta coefficient -0.09; bias-corrected 95%CI -0.166,-0.028; 48.1% of effect mediated). Sense of control was insignificant as a mediator of the relationship between racism and tooth brushing. High levels of self-reported racism were associated with non-optimal tooth brushing behaviours, and perceived stress mediated this association among this sample of pregnant Aboriginal women.. Limitations and implications are discussed.

The Prevalence of Tooth Wear in the Dutch Adult Population

PubMed Central

Wetselaar, Peter; Vermaire, Jan H.; Visscher, Corine M.; Lobbezoo, Frank; Schuller, Annemarie A.

2016-01-01

This study aimed to assess the prevalence of tooth wear in different age groups of the Dutch adult population and to determine this tooth wear distribution by gender, socioeconomic class, and type of teeth. Results were compared with the outcomes of a previous study in a comparable population. As part of a comprehensive investigation of the oral health of the general Dutch adult population in 2013, tooth wear was assessed among 1,125 subjects in the city of ‘s-Hertogenbosch. The data collected were subjected to stratified analysis by 5 age groups (25-34, 35-44, 45-54, 55-64, and 65-74 years), gender, socioeconomic class, and type of teeth. Tooth wear was assessed using a 5-point ordinal occlusal/incisal grading scale. The number of teeth affected was higher in older age groups. Men showed more tooth wear than women, and subjects with low socioeconomic status (low SES) showed on average higher scores than those with high SES. Tooth wear prevalence found in this study was higher in all age groups than in the previous study. The present study found prevalences of 13% for mild tooth wear and 80% for moderate tooth wear, leading to the conclusion that these are common conditions in the Dutch adult population. Severe tooth wear (prevalence 6%) may however be characterized as rare. A tendency was found for there to be more tooth wear in older age groups, in men as compared with women, in persons with lower SES, and in the present survey as compared with the previous one. PMID:27694757

Tooth wear in the elderly population in South East Local Government area in Ibadan, Nigeria.

PubMed

Taiwo, J O; Ogunyinka, A; Onyeaso, C O; Dosumu, O O

2005-12-01

It is the aim of this study to determine the pattern and degree of tooth wear in the elderly population in the South East Local Government Area in Ibadan. The study was carried out on 690 elderly individuals who were 65 years old and above, living in various wards in South East Local Government Area, in Ibadan. A multistage sampling technique was used to select elderly individuals for the study. Two interviewers, 2-record clerks and 2 examiners were trained for the study and the examiners were calibrated. The index of Eccles J.D was used to determine the severity of tooth wear. The results highlight the high prevalence of tooth wear, mainly attrition in the elderly in this local government area. Six hundred and forty (92.8%) of the elderly had tooth wear. Of these 58.59% were males and 41.41% females. Attrition was observed in 618 (89.6%) elderly individuals. The mandible exhibited a higher prevalence of tooth wear than the maxilla and was statistically significant. Severe tooth wear was observed in only 5.74% of the teeth whilst moderate and mild tooth wear were observed in 26.91% and 30.88% respectively. Unlike the Western European countries, attrition being the most common type of tooth wear in these elderly individuals suggests that the aetiological factors responsible for tooth wear are different. Common habits such as crushing of bones and chewing of sticks for routine oral hygiene care could be contributing factors to tooth wear in this environment.

The Prevalence of Tooth Wear in the Dutch Adult Population.

PubMed

Wetselaar, Peter; Vermaire, Jan H; Visscher, Corine M; Lobbezoo, Frank; Schuller, Annemarie A

2016-01-01

This study aimed to assess the prevalence of tooth wear in different age groups of the Dutch adult population and to determine this tooth wear distribution by gender, socioeconomic class, and type of teeth. Results were compared with the outcomes of a previous study in a comparable population. As part of a comprehensive investigation of the oral health of the general Dutch adult population in 2013, tooth wear was assessed among 1,125 subjects in the city of 's-Hertogenbosch. The data collected were subjected to stratified analysis by 5 age groups (25-34, 35-44, 45-54, 55-64, and 65-74 years), gender, socioeconomic class, and type of teeth. Tooth wear was assessed using a 5-point ordinal occlusal/incisal grading scale. The number of teeth affected was higher in older age groups. Men showed more tooth wear than women, and subjects with low socioeconomic status (low SES) showed on average higher scores than those with high SES. Tooth wear prevalence found in this study was higher in all age groups than in the previous study. The present study found prevalences of 13% for mild tooth wear and 80% for moderate tooth wear, leading to the conclusion that these are common conditions in the Dutch adult population. Severe tooth wear (prevalence 6%) may however be characterized as rare. A tendency was found for there to be more tooth wear in older age groups, in men as compared with women, in persons with lower SES, and in the present survey as compared with the previous one. © 2016 S. Karger AG, Basel.

Thick Disks in the Hubble Space Telescope Frontier Fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elmegreen, Bruce G.; Elmegreen, Debra Meloy; Tompkins, Brittany

Thick disk evolution is studied using edge-on galaxies in two Hubble Space Telescope Frontier Field Parallels. The galaxies were separated into 72 clumpy types and 35 spiral types with bulges. Perpendicular light profiles in F435W, F606W, and F814W ( B , V , and I ) passbands were measured at 1 pixel intervals along the major axes and fitted to sech{sup 2} functions convolved with the instrument line spread function (LSF). The LSF was determined from the average point spread function of ∼20 stars in each passband and field, convolved with a line of uniform brightness to simulate disk blurring.more » A spread function for a clumpy disk was also used for comparison. The resulting scale heights were found to be proportional to galactic mass, with the average height for a 10{sup 10±0.5} M {sub ⊙} galaxy at z = 2 ± 0.5 equal to 0.63 ± 0.24 kpc. This value is probably the result of a blend between thin and thick disk components that cannot be resolved. Evidence for such two-component structure is present in an inverse correlation between height and midplane surface brightness. Models suggest that the thick disk is observed best between the clumps, and there the average scale height is 1.06 ± 0.43 kpc for the same mass and redshift. A 0.63 ± 0.68 mag V − I color differential with height is also evidence for a mixture of thin and thick components.« less

21 CFR 872.3580 - Preformed gold denture tooth.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a) Identification. A preformed gold denture tooth is a device composed of austenitic alloys or alloys containing 75...

21 CFR 872.3580 - Preformed gold denture tooth.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a) Identification. A preformed gold denture tooth is a device composed of austenitic alloys or alloys containing 75...

21 CFR 872.3580 - Preformed gold denture tooth.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a) Identification. A preformed gold denture tooth is a device composed of austenitic alloys or alloys containing 75...

21 CFR 872.3580 - Preformed gold denture tooth.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a) Identification. A preformed gold denture tooth is a device composed of austenitic alloys or alloys containing 75...

21 CFR 872.3580 - Preformed gold denture tooth.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a) Identification. A preformed gold denture tooth is a device composed of austenitic alloys or alloys containing 75...

21 CFR 872.3590 - Preformed plastic denture tooth.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as methyl...

21 CFR 872.3750 - Bracket adhesive resin and tooth conditioner.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bracket adhesive resin and tooth conditioner. 872... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3750 Bracket adhesive resin and tooth conditioner. (a) Identification. A bracket adhesive resin and tooth conditioner is a device...

21 CFR 872.3590 - Preformed plastic denture tooth.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as methyl...

21 CFR 872.3590 - Preformed plastic denture tooth.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as methyl...

21 CFR 872.3590 - Preformed plastic denture tooth.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as methyl...

21 CFR 872.3590 - Preformed plastic denture tooth.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as methyl...

Integral freeform illumination lens design of LED based pico-projector.

PubMed

Zhao, Shuang; Wang, Kai; Chen, Fei; Qin, Zong; Liu, Sheng

2013-05-01

In this paper, an illumination lens design for a LED-based pico-projector is presented. Different from the traditional illumination systems composed by lens group, the integral illumination lens consists of a total internal reflector (TIR) and a freeform surface. TIR acts as collimation lens and its top surface formed by a freeform surface reshapes the nonuniform circular light pattern generated by TIR to be rectangular and uniform. Diameter and height of the lens are 16 and 10 mm, respectively. An optimization method to deal with the problem of extended light source is also presented in detail in this paper. According to the simulation results of the final optimized lens, 77% (neglecting the effect of polarization) of the power of light source is collected on liquid crystal on silicon panel with a 16∶9 ratio and illumination uniformity achieves 92%.

Simulation design of uniform low turn-on voltage and high reverse blocking AlGaN/GaN power field effect rectifier with trench heterojunction anode

NASA Astrophysics Data System (ADS)

Wang, Fangzhou; Chen, Wanjun; Wang, Zeheng; Sun, Ruize; Wei, Jin; Li, Xuan; Shi, Yijun; Jin, Xiaosheng; Xu, Xiaorui; Chen, Nan; Zhou, Qi; Zhang, Bo

2017-05-01

To achieve uniform low turn-on voltage and high reverse blocking capability, an AlGaN/GaN power field effect rectifier with trench heterojunction anode (THA-FER) is proposed and investigated in this work which includes only simulated data and no real experimental result. VT has a low saturation value when trench height (HT) is beyond 300 nm, confirming it is possible to control the VT accurately without precisely controlling the HT in the THA-FER. Meanwhile, high HT anode reduces reverse leakage current and yields high breakdown voltage (VB). A superior high Baliga's Figure of Merits (BFOM = VB2/Ron,sp, Ron,sp is specific-on resistance) of 1228 MW/cm2 reveals the THA-FER caters for the demands of high efficiency GaN power applications.

Experimental physics characteristics of a heavy-metal-reflected fast-spectrum critical assembly

NASA Technical Reports Server (NTRS)

Heneveld, W. H.; Paschall, R. K.; Springer, T. H.; Swanson, V. A.; Thiele, A. W.; Tuttle, R. J.

1972-01-01

A zero-power critical assembly was designed, constructed, and operated for the purpose of conducting a series of benchmark experiments dealing with the physics characteristics of a UN-fueled, Li-cooled, Mo-reflected, drum-controlled compact fast reactor for use with a space-power electric conversion system. The range of the previous experimental investigations has been expanded to include the reactivity effects of:(1) surrounding the reactor with 15.24 cm (6 in.) of polyethylene, (2) reducing the heights of a portion of the upper and lower axial reflectors by factors of 2 and 4, (3) adding 45 kg of W to the core uniformly in two steps, (4) adding 9.54 kg of Ta to the core uniformly, and (5) inserting 2.3 kg of polyethylene into the core proper and determining the effect of a Ta addition on the polyethylene worth.

Adding muscle where you need it: non-uniform hypertrophy patterns in elite sprinters.

PubMed

Handsfield, G G; Knaus, K R; Fiorentino, N M; Meyer, C H; Hart, J M; Blemker, S S

2017-10-01

Sprint runners achieve much higher gait velocities and accelerations than average humans, due in part to large forces generated by their lower limb muscles. Various factors have been explored in the past to understand sprint biomechanics, but the distribution of muscle volumes in the lower limb has not been investigated in elite sprinters. In this study, we used non-Cartesian MRI to determine muscle sizes in vivo in a group of 15 NCAA Division I sprinters. Normalizing muscle sizes by body size, we compared sprinter muscles to non-sprinter muscles, calculated Z-scores to determine non-uniformly large muscles in sprinters, assessed bilateral symmetry, and assessed gender differences in sprinters' muscles. While limb musculature per height-mass was 22% greater in sprinters than in non-sprinters, individual muscles were not all uniformly larger. Hip- and knee-crossing muscles were significantly larger among sprinters (mean difference: 30%, range: 19-54%) but only one ankle-crossing muscle was significantly larger (tibialis posterior, 28%). Population-wide asymmetry was not significant in the sprint population but individual muscle asymmetries exceeded 15%. Gender differences in normalized muscle sizes were not significant. The results of this study suggest that non-uniform hypertrophy patterns, particularly large hip and knee flexors and extensors, are advantageous for fast sprinting. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

[Experience, prevalence and severity of dental caries and its association with nutritional status in Mexican infants 17-47 months].

PubMed

Zúñiga-Manríquez, Ana Gabriela; Medina-Solís, Carlo Eduardo; Lara-Carrillo, Edith; Márquez-Corona, María de Lourdes; Robles-Bermeo, Norma Leticia; Scougall-Vilchis, Rogelio José; Maupomé, Gerardo

2013-01-01

To determine the experience, prevalence and severity of dental caries and its relationship with nutritional status in nursery infants 17 to 47 months of age. A cross-sectional study in 152 infants 17 to 47 months of age attending one of five day care centers of the city of Pachuca, Hidalgo was performed. Clinical examinations were performed using the methods recommended by the World Health Organization for epidemiologic studies on dental caries. We calculated the caries index (dmft), the significant caries index (SiC) as well as the treatment needs index (TNI) and the care index (CI). Nutritional status was determined using the weight and height for age, in Federico Gomez's scale. In the statistical analysis nonparametric tests were used. Mean age was 2.52 ± 0.76 years; 51.3% were boys. With regard to nutritional status, 19.1% were classified as malnourished and 19.1% were overweight/obese. The dmft index was 1.53 ± 2.52. The SiC index was 4.14, the TNI 86.3% and the CI 13.7%. Caries prevalence was 48.0%. It was observed that 33.5% of children had 1 to 3 teeth with caries experience and 14.5% had 4 or more teeth affected. Statistically significant differences for tooth decay were identified (p < 0.05) by age, height and weight but not (p> 0.05) by sex and nutritional status. This study shows that nearly half of children examined had caries experience. High treatment needs for dental caries were observed. A correlation was found between dmft index and age, weight and height. No association was identified between experience, prevalence and severity of dental caries and nutritional status of infants. It appears necessary to improve oral health preventive measures in these infants.

Morphometric analysis of developing crowns of maxillary primary second molars and permanent first molars in humans.

PubMed

Peretz, B; Nevis, N; Smith, P

1998-07-01

The purpose of this study was firstly to characterize the changes occurring in size and form of the mineralizing maxillary second primary molar and first permanent molar crowns, and secondly to determine if similar changes in size and form characterize enamel apposition in the crowns of these teeth. Twenty-five primary second molars and 20 maxillary permanent first molars at various stages of development, found in archaeological excavations in Israel, were examined for a number of measured variables using image analyser software. Teeth were divided into two groups according to their stage of development: stage I included all teeth at an early stage of development in which mesiobuccal-cusp height was less than 5 mm for the primary molar and 5.9 mm for the permanent molar; stage 2 included all teeth in later stages of development where mesiobuccal-cusp height was greater than these values. In the primary molar, a significant increase was found between the two stages in almost all variables. Significant correlations were also found between all intercusp distances and the external variables. Strong correlations between height of the mesiobuccal cusp and all external and internal variables were noted in stage 1, but fewer in stage 2. In the permanent tooth, no increase was observed in intercusp distances and very few correlations were found between and among the variables. The results suggest that a change in the shape of the maxillary primary second molar occurs during formation, with the lingual cusp tips moving lingually and distally, and the distobuccal cusp tips moving distally. No change occurs in the shape of the maxillary permanent first molar during crown formation. Growth of the maxillary primary second and permanent first molar crowns occurs in 'bursts' of development.

The mandibular third molar position as a predictive criteria for risk for pericoronitis: a retrospective study.

PubMed

Halverson, B A; Anderson, W H

1992-03-01

During the 6-month period from mid February 1988 to mid August 1988, 148 patients presented with 154 diagnosed cases of mandibular third molar pericoronitis. All patients were members of the recruit population stationed at the Recruit Training Command, Great Lakes, Illinois. Selected clinical parameters relating to the orientation and eruption status of these third molars were collected and analyzed. The goal was to obtain a predictive clinical profile of the impacted mandibular third molar (MTM) at greatest risk for pericoronitis in the young naval and Marine Corps personnel. The majority of pericoronitis cases, 120 of 148 or 81.0%, involved vertically oriented MTMs; of this total, 79.1% were erupted to the approximate height of the occlusal plane of the arch. The remaining 20.9% were at or below the height of contour of the adjacent tooth. Mesioangular impacted MTMs accounted for only 11.2% of pericoronitis cases. The remaining cases comprised distoangular and horizontally impacted MTMs (3.4% and 3.8%, respectively). Involvement by impinging maxillary dentition was observed in 39.7% of the vertically oriented MTMs, 56.2% of the mesioangular oriented MTMs, 40.0% of the distoangular MTMs, and 14.0% of the horizontally impacted MTMs. The mean value for occlusal coverage by a soft tissue operculum observed for all MTMs in this study was 49%. In the population studied, risk for pericoronitis appears to increase with greater vertical orientation and height of eruption. The absence of impinging maxillary dentition did not eliminate the risk of mandibular third molar pericoronitis. These data have implications for targeting treatment needs of naval and Marine Corps personnel who may be without dental support for extended periods of time.

A Dental Hygienist's and Therapist's Guide to the Management of Tooth Erosion.

PubMed

Ariyanayagam, Yana

2016-08-01

Dental care professionals can support patients to prevent and manage tooth erosion. The role of the dentist is to restore the structure and function of teeth damaged by acid erosion, while the role of the dental hygienist therapist is to work alongside the dentist to help manage and reduce the risk of tooth erosion. This article will highlight how the dental hygienist or therapist can identify tooth erosion. It will describe the features of tooth erosion and outline the causes. This article will discuss preventative care options for patients who are at risk of tooth erosion, including specific oral hygiene instructions, fluoride advice and use of other dental products.

Application study of magnetic fluid seal in hydraulic turbine

NASA Astrophysics Data System (ADS)

Yu, Z. Y.; Zhang, W.

2012-11-01

The waterpower resources of our country are abundant, and the hydroelectric power is developed, but at present the main shaft sealing device of hydraulic turbine is easy to wear and tear and the leakage is great. The magnetic fluid seal has the advantages of no contact, no wear, self-healing, long life and so on. In this paper, the magnetic fluid seal would be used in the main shaft of hydraulic turbine, the sealing structure was built the model, meshed the geometry, applied loads and solved by using MULTIPHYSICS in ANSYS software, the influence of the various sealing structural parameters such as tooth width, height, slot width, sealing gap on the sealing property were analyzed, the magnetic fluid sealing device suitable for large-diameter shaft and sealing water was designed, the sealing problem of the hydraulic turbine main shaft was solved effectively which will bring huge economic benefits.

Morphology control of layer-structured gallium selenide nanowires.

PubMed

Peng, Hailin; Meister, Stefan; Chan, Candace K; Zhang, Xiao Feng; Cui, Yi

2007-01-01

Layer-structured group III chalcogenides have highly anisotropic properties and are attractive materials for stable photocathodes and battery electrodes. We report the controlled synthesis and characterization of layer-structured GaSe nanowires via a catalyst-assisted vapor-liquid-solid (VLS) growth mechanism during GaSe powder evaporation. GaSe nanowires consist of Se-Ga-Ga-Se layers stacked together via van der Waals interactions to form belt-shaped nanowires with a growth direction along the [11-20], width along the [1-100], and height along the [0001] direction. Nanobelts exhibit a variety of morphologies including straight, zigzag, and saw-tooth shapes. These morphologies are realized by controlling the growth temperature and time so that the actual catalysts have a chemical composition of Au, Au-Ga alloy, or Ga. The participation of Ga in the VLS catalyst is important for achieving different morphologies of GaSe. In addition, GaSe nanotubes are also prepared by a slow growth process.

Alumina-zirconia machinable abutments for implant-supported single-tooth anterior crowns.

PubMed

Sadoun, M; Perelmuter, S

1997-01-01

Innovative materials and application techniques are constantly being developed in the ongoing search for improved restorations. This article describes a new material and the fabrication process of aesthetic machinable ceramic anterior implant abutments. The ceramic material utilized is a mixture of alumina (aluminum oxide) and ceria (cerium oxide) with partially stabilized zirconia (zirconium oxide). The initial core material is a cylinder with a 9-mm diameter and a 15-mm height, obtained by ceramic injection and presintering processes. The resultant alumina-zirconia core is porous and readily machinable. It is secured to the analog, and its design is customized by machining the abutment to suit the particular clinical circumstances. The machining is followed by glass infiltration, and the crown is finalized. The learning objective of this article is to gain a basic knowledge of the fabrication and clinical application of the custom machinable abutments.

Astragalar Morphology of Selected Giraffidae.

PubMed

Solounias, Nikos; Danowitz, Melinda

2016-01-01

The artiodactyl astragalus has been modified to exhibit two trochleae, creating a double pullied structure allowing for significant dorso-plantar motion, and limited mediolateral motion. The astragalus structure is partly influenced by environmental substrates, and correspondingly, morphometric studies can yield paleohabitat information. The present study establishes terminology and describes detailed morphological features on giraffid astragali. Each giraffid astragalus exhibits a unique combination of anatomical characteristics. The giraffid astragalar morphologies reinforce previously established phylogenetic relationships. We find that the enlargement of the navicular head is a feature shared by all giraffids, and that the primitive giraffids possess exceptionally tall astragalar heads in relation to the total astragalar height. The sivatheres and the okapi share a reduced notch on the lateral edge of the astragalus. We find that Samotherium is more primitive in astragalar morphologies than Palaeotragus, which is reinforced by tooth characteristics and ossicone position. Diagnostic anatomical characters on the astragalus allow for giraffid species identifications and a better understanding of Giraffidae.

Therapeutic Challenge in a Severely Atrophic Mandible

PubMed Central

Janev, Edvard; Janeva, Nadica; Peeva–Petreska, Marija; Mitic, Kristina

2018-01-01

BACKGROUND: After tooth loss, however, severely atrophic residual alveolar ridges are fairly common, especially in patients who have been edentulous for a long period. Anterior area of the mandible is areas where clinicians have greater anatomical limitations. Reduced alveolar bone height very often represents a contraindication to implant therapy, unless a procedure such as a ridge augmentation is performed. CASE REPORT: This study aims to present two separate cases in highly selected edentulous anterior mandibular sites, where one stage, mini implants were used to support total prostheses. Small diameter implants have been used for retention of complete removable mandibular overdentures. This is an excellent option for those who suffer from the inconvenience and embarrassment of loose lower dentures and are tired of having to use sticky pastes and creams to make their dentures stay in place. CONCLUSION: Small diameter implants, when used multiples may offer adequate support for a removable prosthesis and overcome this problem. PMID:29610621

[A study on the mechanical behaviors of abutment teeth with various coping designs under overdenture].

PubMed

Vang, M S; Cho, J H

1990-04-01

An overdenture is a complete denture supported by both soft tissue and a few remaining natural teeth. The purpose of this study was to analyze the stress distribution of the teeth and supporting structures when various type of coping under overdenture was applied. The analysis was conducted by using the finite element method and changing the condition such as the direction of the load, the shape of coping on the abutment: The model included overdenture copings, abutment tooth and supporting structures. The results of analysis were as follows: 1. The short dome coping showed well distribution of stress. 2. The dome shaped design produced higher stress distribution than square and inclined plane design. 3. As the height of copings on the abutment was increased, the displacements increased. 4. The magnitude and direction of the abutment displacements were influenced by the direction of load application.

The perio-esthetic-restorative approach for anterior rehabilitation

PubMed Central

Tomar, Nitin; Bansal, Tushika; Bhandari, Marisha; Sharma, Anamika

2013-01-01

Ensuring clinical success begins with a careful discussion of treatment planning, comprehensively covering all variables in simple to complex cases. Procedures including the crown lengthening surgery, furcation treatment and mucogingival therapy and tooth restoration are essential treatment regimens requiring multifaceted expertise. The interplay of periodontics and restorative dentistry is present at many fronts including the response of the gingival tissue to the restorative preparations. Dental restorations and periodontal health are inseparably interrelated. The adaptation of the margins, the contours of the restoration, the proximal relationships and the surface smoothness have a critical biological impact on the gingiva and the supporting periodontal tissues. The different surgical procedures used for crown lengthening are gingivectomy/gingivoplasty, apically positioned flap with or without osseous resection and orthodontic extrusion. The paper presents crown lengthening of severely mutilated teeth to increase the clinical crown height for adequate restoration. PMID:24174740

Automatic estimation of dynamics of ionospheric disturbances with 1–15 minute lifetimes as derived from ISTP SB RAS fast chirp-ionosonde data

NASA Astrophysics Data System (ADS)

Berngardt, Oleg; Bubnova, Tatyana; Podlesnyi, Aleksey

2018-03-01

We propose and test a method of analyzing ionograms of vertical ionospheric sounding, which is based on detecting deviations of the shape of an ionogram from its regular (averaged) shape. We interpret these deviations in terms of reflection from the electron density irregularities at heights corresponding to the effective height. We examine the irregularities thus discovered within the framework of a model of a localized uniformly moving irregularity, and determine their characteristic parameters: effective heights and observed vertical velocities. We analyze selected experimental data for three seasons (spring, winter, autumn) obtained nearby Irkutsk with a fast chirp ionosonde of ISTP SB RAS in 2013-2015. The analysis of six days of observations conducted in these seasons has shown that in the observed vertical drift of the irregularities there are two characteristic distributions: wide velocity distribution with nearly 0 m/s mean and with the standard deviation of ∼250 m/s and narrow distribution with nearly -160 m/s mean. The analysis has demonstrated the effectiveness of the proposed algorithm for the automatic analysis of vertical sounding data with high repetition rate.

A numerical analysis of flat fan aerial crop spray

NASA Astrophysics Data System (ADS)

Malik Fesal, Siti Natasha; Fawzi, Mas; Omar, Zamri

2017-09-01

Spray drift mitigation, in the agriculture aerial spraying literature, and spray quality in the application of plant protection products, still continues as two critical components in evaluating shareholder value. A study on off-target drift and ground deposit onto a 250 m strip were simulated through series of Computational Fluid Dynamic (CFD) simulations. The drift patterns for evaporating droplets were released from a constant aircraft velocity at 30 m/s (60 mph) carrying 20 m swath width spray boom with 12 fan-type nozzles at released height from the ground ranging from 3.7 m to 4.7 m. Droplet trajectories are calculated from the given airspeed with a Lagrangian model for particle dispersion excluding any wind effect perturbation. The proposed CFD’s model predictions agreed well with cited literatures for a wide range of atmospheric stability values. The results revealed that there is considerable increased in spray drift and droplets trajectories with the increased in spray released height. It suggested that a combination of low aircraft spray released height with low airspeed is essential to improve spray quality and maximizing uniform deposition on the target area are significant in minimizing spray drift risks.

[Effect of greenbelt on pollutant dispersion in street canyon].

PubMed

Xu, Wei-Jia; Xing, Hong; Yu, Zhi

2012-02-01

The effect feature of greenbelt on flow field and pollutant dispersion in urban street canyon was researched. The greenbelt was assumed as uniform porous media and its aerodynamics property defined by the pressure loss coefficient. Subsequently, the pollutant dispersion in the street canyon of which there was greenbelt in the middle was simulated with the steady-state standard kappa-epsilon turbulence model and species transport equation. The simulated results agreed well with the wind-tunnel data. Compared with the treeless case, it finds that the street canyon contain a clockwise vortex, the pollutant concentration of the leeward was several times than the windward and the growth rate of pollutant concentration was 46.0%. The further simulation for the impact of tree crown position on the airflow and pollutant dispersion finds that the height of major vortex center in the street canyon increases with the height of tree crown and gradually closes the top of windward building This causes that the average wind speed in the street canyon decreases. Especially when the top of tree crown over the roof and hinder the air flow above the street canyon, the average pollutant concentration increases with the height of tree crown rapidly.

Management of Tooth Surface Loss of Varying Etiology with Full Mouth all Ceramic Computer-Aided Design/Computer-Aided Manufacture Restorations.

PubMed

Bettie, Nirmal Famila; Kandasamy, Saravanan; Prasad, Venkat

2017-11-01

The anatomical form of a tooth can undergo changes leading to loss of tooth form. The loss of tooth surface can be due to varying etiology. Dental caries, attrition, abrasion, erosion, involving any surface of the tooth can lead to loss of tooth structure. The rate of tooth destruction may proceed to such an extent that the esthetics, function and comfort may be lost. The role of a practioner lies in identification and screening of such case and motivate for oral rehabilitation that includes habit cessation. Computerized dentistry has raised the bar as far as esthetic restorations are concerned. Demanding esthetics has made zirconia crowns as the material of choice in full mouth rehabilitations. However, appropriate treatment planning with scientific evidence and a recommended treatment protocol with careful implementation results in successful restorations and satisfied patients.

Inequalities in Tooth Decay in Australian Children by Neighbourhood Characteristics and Indigenous Status.

PubMed

Lalloo, Ratilal; Jamieson, Lisa M; Ha, Diep; Luzzi, Liana

2016-01-01

Tooth decay is related to poverty, measured at individual and neighbourhood levels. It is however uncertain if living in an advantaged neighbourhood reduces tooth decay similarly in Australian Indigenous and non-Indigenous children. This study describes tooth decay by neighbourhood characteristics and Indigenous status, and examines inequalities by Indigenous status. In deciduous dentition the percentage of children with tooth decay and untreated decay decreased on average 26% and 20% respectively in the non-Indigenous sample from poor to affluent neighbourhoods. In Indigenous children tooth decay and untreated decay decreased on average 6% and 8%, respectively, from poor to affluent neighbourhoods. While all children from affluent areas had less tooth decay, the gap between non-Indigenous and Indigenous children remained significant across neighbourhood characteristics. This suggests that both universal and targeted prevention programs should be considered for all Indigenous children irrespective of where they live.

Inequalities in Tooth Decay in Australian Children by Neighbourhood Characteristics and Indigenous Status.

PubMed

Lalloo, Ratilal; Jamieson, Lisa M; Ha, Diep; Luzzi, Liana

2016-02-01

Tooth decay is related to poverty, measured at individual and neighbourhood levels. It is however uncertain if living in an advantaged neighbourhood reduces tooth decay similarly in Australian Indigenous and non-Indigenous children. This study describes tooth decay by neighbourhood characteristics and Indigenous status, and examines inequalities by Indigenous status. In deciduous dentition the percentage of children with tooth decay and untreated decay decreased on average 26% and 20% respectively in the non-Indigenous sample from poor to affluent neighbourhoods. In Indigenous children tooth decay and untreated decay decreased on average 6% and 8%, respectively, from poor to affluent neighbourhoods. While all children from affluent areas had less tooth decay, the gap between non-Indigenous and Indigenous children remained significant across neighbourhood characteristics. This suggests that both universal and targeted prevention programs should be considered for all Indigenous children irrespective of where they live.

Test Tube Tooth: The Next Big Thing.

PubMed

Yadav, Preeti; Tahir, Mohammed; Yadav, Harsh; Sureka, Rakshit; Garg, Aarti

2016-06-01

Unlike some vertebrates and fishes, humans do not have the capacity for tooth regeneration after the loss of permanent teeth. Although artificial replacement with removable dentures, fixed prosthesis and implants is possible through advances in the field of prosthetic dentistry, it would be ideal to recreate a third set of natural teeth to replace lost dentition. For many years now, researchers in the field of tissue engineering have been trying to bioengineer dental tissues as well as whole teeth. In order to attain a whole tooth through dental engineering, that has the same or nearly same biological, mechanical and physical properties of a natural tooth, it's necessary to deal with all the cells and tissues which are concerned with the formation, maintenance and repair of the tooth. In this article we review the steps involved in odontogenesis or organogenesis of a tooth and progress in the bioengineering of a whole tooth.

Nanofibers implant functionalized by neural growth factor as a strategy to innervate a bioengineered tooth.

PubMed

Eap, Sandy; Bécavin, Thibault; Keller, Laetitia; Kökten, Tunay; Fioretti, Florence; Weickert, Jean-Luc; Deveaux, Etienne; Benkirane-Jessel, Nadia; Kuchler-Bopp, Sabine

2014-03-01

Current strategies for jaw reconstruction require multiple procedures, to repair the bone defect, to offer sufficient support, and to place the tooth implant. The entire procedure can be painful and time-consuming, and the desired functional repair can be achieved only when both steps are successful. The ability to engineer combined tooth and bone constructs, which would grow in a coordinated fashion with the surrounding tissues, could potentially improve the clinical outcomes and also reduce patient suffering. A unique nanofibrous and active implant for bone-tooth unit regeneration and also the innervation of this bioengineered tooth are demonstrated. A nanofibrous polycaprolactone membrane is functionalized with neural growth factor, along with dental germ, and tooth innervation follows. Such innervation allows complete functionality and tissue homeostasis of the tooth, such as dentinal sensitivity, odontoblast function, masticatory forces, and blood flow. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Inflammatory myofibroblastic tumor of maxilla showing sarcomatous change in an edentulous site with a history of tooth extraction following periodontitis: A case report with discussion.

PubMed

Biniraj, K R; Janardhanan, Mahija

2014-05-01

Inflammatory myofibroblastic tumor (IMT) is a rare tumor of uncertain origin with variable biological behavior ranging from reactive lesions to highly aggressive malignancy. Oral IMTs are extremely rare and only 25 cases had been reported so far. A case of IMT with sarcomatous transformation in an extraction site with a history of tooth extraction following tooth mobility of an upper left molar tooth is presented here. The tooth was extracted following a complaint of gingival swelling and mobility of tooth. Though malignant transformation in IMTs had been documented in the extra oral sites, wide search of associated literature suggests, this is the first case of oral IMT showing malignant change associated with gingiva. The case report attempts to highlight the variant possibilities of tooth mobility other than periodontitis and the importance of assessing the primary cause of such conditions.

Inflammatory myofibroblastic tumor of maxilla showing sarcomatous change in an edentulous site with a history of tooth extraction following periodontitis: A case report with discussion

PubMed Central

Biniraj, K. R.; Janardhanan, Mahija

2014-01-01

Inflammatory myofibroblastic tumor (IMT) is a rare tumor of uncertain origin with variable biological behavior ranging from reactive lesions to highly aggressive malignancy. Oral IMTs are extremely rare and only 25 cases had been reported so far. A case of IMT with sarcomatous transformation in an extraction site with a history of tooth extraction following tooth mobility of an upper left molar tooth is presented here. The tooth was extracted following a complaint of gingival swelling and mobility of tooth. Though malignant transformation in IMTs had been documented in the extra oral sites, wide search of associated literature suggests, this is the first case of oral IMT showing malignant change associated with gingiva. The case report attempts to highlight the variant possibilities of tooth mobility other than periodontitis and the importance of assessing the primary cause of such conditions. PMID:25024554

The interactions between attrition, abrasion and erosion in tooth wear.

PubMed

Shellis, R Peter; Addy, Martin

2014-01-01

Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Knowledge of these tooth wear processes and their interactions is reviewed. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence is insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear, especially through formation of pellicle, but cannot prevent it. © 2014 S. Karger AG, Basel.

Fused primary first mandibular macromolar with a unique relation to its permanent successors: A rare tooth anomaly.

PubMed

Dhindsa, Abhishek; Garg, Shalini; Damle, S G; Opal, Shireen; Singh, Tavleen

2013-04-01

Dental anomalies of number and forms may occur in the primary and permanent dentition. Various terms have been used to describe dental twinning anomalies: Germination, fusion, concrescence, double teeth, conjoined teeth, twinned teeth, geminifusion, and vicinifusion. Fused tooth is a developmental anomaly that is seen more frequently in the primary than the permanent dentition. Double tooth involving deciduous anterior teeth is found mostly in the mandible. Very few cases of nonsyndromic double primary molar have been reported in the literature. The succeeding permanent tooth is often found missing congenitally in the same region. This article reports a very rare unilateral occurrence of an anomalous, primary mandibular first macromolar formed by fusion with a dysmorphic premolar like supernumerary tooth in deciduous dentition period. Instead of agenesis of succedaneous tooth, the double tooth has been succeeded by normally developing mandibular first premolar in the same region.

Tooth Avulsion in the School Setting

ERIC Educational Resources Information Center

Krause-Parello, Cheryl A.

2005-01-01

Tooth avulsions occur when a tooth is displaced from its socket. Tooth avulsions are common dental injuries that may occur before, during, or after school. Therefore, it is essential that school nurses be well prepared to intervene when such a dental emergency arises. It is also imperative that school nurses and school personnel are fully equipped…

The Importance of Tooth Decay Prevention in Children under Three

ERIC Educational Resources Information Center

Milgrom, Peter; Huebner, Colleen; Chi, Donald

2010-01-01

Tooth decay and tooth loss was once the norm but public health interventions have led to major improvements for most people. Nevertheless, not all children have benefited. Dental disease in young children is unacceptably high. Tooth decay is preventable. Early childhood educators are often the first to notice the problem. Professional…

Aggravated loss of tooth structure.

PubMed

Barsby, M J

1989-09-01

Self-inflicted tooth modification other than ritual mutilation practised in some countries is a rare occurrence. The author reports a case of aggravated loss of tooth structure where a patient has contributed to loss of tooth structure by the novel method of adjusting his natural teeth with a 'knife'. Subsequent management of the case is discussed.

Use of elevator instruments when luxating and extracting teeth in dentistry: clinical techniques

PubMed Central

2017-01-01

In dentistry, elevator instruments are used to luxate teeth, and this technique imparts forces to tooth particles that sever the periodontal ligament around tooth roots inside the socket and expand alveolar bone around tooth particles. These effects can result in extraction of the tooth particles or facilitate systematic forceps extraction of the tooth particles. This article presents basic oral surgery techniques for applying elevators to luxate teeth. Determination of the optimal luxation technique requires understanding of the functions of the straight elevator and the Cryer elevator, the concept of purchase points, how the design elements of elevator working ends and tips influence the functionality of an elevator, application of forces to tooth particles, sectioning teeth at furcations, and bone removal to facilitate luxation. The effectiveness of tooth particle luxation is influenced by elevator tip shape and size, the magnitude and the vectors of forces applied to the tooth particle by the tip, and sectioning and bone removal within the operating field. Controlled extraction procedures are facilitated by a dental operating microscope or the magnification of binocular surgical loupes telescopes, combined with co-axial illumination. PMID:28770164

A review of tooth colour and whiteness.

PubMed

Joiner, Andrew; Hopkinson, Ian; Deng, Yan; Westland, Stephen

2008-01-01

To review current knowledge on the definition of tooth whiteness and its application within dentistry, together with the measured range of tooth colours. 'Medline' and 'ISI Web of Sciences' databases were searched electronically with key words tooth, teeth, colour, colour, white and whiteness. The application of colour science within dentistry has permitted the measurement of tooth colour in an objective way, with the most common colour space in current use being the CIELAB (Commission Internationale de l'Eclairage). Indeed, many investigators from a range of different countries have reported L*, a* and b* values for teeth measured in vivo using instrumental techniques such as spectrophotometers, colorimeters and image analysis of digital images. In general, these studies show a large range in L*, a* and b* values, but consistently show that there is a significant contribution of b* value or yellowness in natural tooth colour. Further developments in colour science have lead to the description of tooth whiteness and changes in tooth whiteness based on whiteness indices, with the most relevant and applicable being the WIO whiteness index, a modified version of the CIE whiteness index.

Visual and digital comparative tooth colour assessment methods and atomic force microscopy surface roughness.

PubMed

Grundlingh, A A; Grossman, E S; Shrivastava, S; Witcomb, M J

2013-10-01

This study compared digital and visual colour tooth colour assessment methods in a sample of 99 teeth consisting of incisors, canines and pre-molars. The teeth were equally divided between Control, Ozicure Oxygen Activator bleach and Opalescence Quick bleach and subjected to three treatments. Colour readings were recorded at nine intervals by two assessment methods, VITA Easyshade and VITAPAN 3D MASTER TOOTH GUIDE, giving a total of 1782 colour readings. Descriptive and statistical analysis was undertaken using a GLM test for Analysis of Variance for a Fractional Design set at a significance of P < 0.05. Atomic force micros copy was used to examine treated ename surfaces and establish surface roughness. Visual tooth colour assessment showed significance for the independent variables of treatment, number of treatments, tooth type and the combination tooth type and treatment. Digital colour assessment indicated treatment and tooth type to be of significance in tooth colour change. Poor agreement was found between visual and digital colour assessment methods for Control and Ozicure Oxygen Activator treatments. Surface roughness values increased two-fold for Opalescence Quick specimens over the two other treatments, implying that increased light scattering improved digital colour reading. Both digital and visual colour matching methods should be used in tooth bleaching studies to complement each other and to compensate for deficiencies.

Accelerated tooth eruption in children with diabetes mellitus.

PubMed

Lal, Shantanu; Cheng, Bin; Kaplan, Selma; Softness, Barney; Greenberg, Ellen; Goland, Robin S; Lalla, Evanthia; Lamster, Ira B

2008-05-01

The objective of this study was to evaluate tooth eruption in 6- to 14-year-old children with diabetes mellitus. Tooth eruption status was assessed for 270 children with diabetes and 320 control children without diabetes. Data on important diabetes-related variables were collected. Analyses were performed using logistic regression models. Children with diabetes exhibited accelerated tooth eruption in the late mixed dentition period (10-14 years of age) compared to healthy children. For both case patients and control subjects the odds of a tooth being in an advanced eruptive stage were significantly higher among girls than boys. There was also a trend associating gingival inflammation with expedited tooth eruption in both groups. No association was found between the odds of a tooth being in an advanced stage of eruption and hemoglobin A(1c) or duration of diabetes. Patients with higher body mass index percentile demonstrated statistically higher odds for accelerated tooth eruption, but the association was not clinically significant. Children with diabetes exhibit accelerated tooth eruption. Future studies need to ascertain the role of such aberrations in dental development and complications such as malocclusion, impaired oral hygiene, and periodontal disease. The standards of care for children with diabetes should include screening and referral programs aimed at oral health promotion and disease prevention.

Innovative Design and Performance Evaluation of Bionic Imprinting Toothed Wheel

PubMed Central

Wang, Xiaoyang; Tong, Jin; Stephen, Carr

2018-01-01

A highly efficient soil-burrowing dung beetle possesses an intricate outer contour curve on its foreleg end-tooth. This study was carried out based on evidence that this special outer contour curve has the potential of reducing soil penetration resistance and could enhance soil-burrowing efficiency. A toothed wheel is a typical agricultural implement for soil imprinting, to increase its working efficiency; the approach of the bionic geometrical structure was utilized to optimize the innovative shape of imprinting toothed wheel. Characteristics in the dung beetle's foreleg end-tooth were extracted and studied by the edge detection technique. Then, this special outer contour curve was modeled by a nine-order polynomial function and used for the innovative design of imprinting the tooth's cutting edge. Both the conventional and bionic teeth were manufactured, and traction tests in a soil bin were conducted. Taking required draft force and volume of imprinted microbasin as the evaluating indexes, operating efficiency and quality of different toothed wheels were compared and investigated. Results indicate that compared with the conventional toothed wheel, a bionic toothed wheel possesses a better forward resistance reduction property against soil and, meanwhile, can enhance the quality of soil imprinting by increasing the volume of the created micro-basin. PMID:29515651

The regulation of tooth morphogenesis is associated with epithelial cell proliferation and the expression of Sonic hedgehog through epithelial-mesenchymal interactions.

PubMed

Ishida, Kentaro; Murofushi, Mayumi; Nakao, Kazuhisa; Morita, Ritsuko; Ogawa, Miho; Tsuji, Takashi

2011-02-18

Ectodermal organs, such as the tooth, salivary gland, hair, and mammary gland, develop through reciprocal epithelial-mesenchymal interactions. Tooth morphologies are defined by the crown width and tooth length (macro-morphologies), and by the number and locations of the cusp and roots (micro-morphologies). In our current study, we report that the crown width of a bioengineered molar tooth, which was reconstructed using dissociated epithelial and mesenchymal cells via an organ germ method, can be regulated by the contact area between epithelial and mesenchymal cell layers. We further show that this is associated with cell proliferation and Sonic hedgehog (Shh) expression in the inner enamel epithelium after the germ stage has formed a secondary enamel knot. We also demonstrate that the cusp number is significantly correlated with the crown width of the bioengineered tooth. These findings suggest that the tooth micro-morphology, i.e. the cusp formation, is regulated after the tooth width, or macro-morphology, is determined. These findings also suggest that the spatiotemporal patterning of cell proliferation and the Shh expression areas in the epithelium regulate the crown width and cusp formation of the developing tooth. Copyright © 2011 Elsevier Inc. All rights reserved.

Autotransplantation of Mandibular Third Molar with Buccal Cortical Plate to Replace Vertically Fractured Mandibular Second Molar: A Novel Technique.

PubMed

Zufía, Juan; Abella, Francesc; Trebol, Ivan; Gómez-Meda, Ramón

2017-09-01

Tooth replacement often leads to inadequate vertical volume in the recipient site bone when a tooth has been extracted because of a vertical root fracture (VRF). This case report presents the autotransplantation of a mandibular third molar (tooth #32) with the attached buccal cortical plate to replace a mandibular second molar (tooth #31) diagnosed with a VRF. After extraction of tooth #31, the recipient socket was prepared based on the size measured in advance with cone-beam computed tomographic imaging. The precise and calculated osteotomy of the cortical bone of tooth #32 allowed for the exact placement of the donor tooth in the position of tooth #31. The total extraoral time was only 25 minutes. The block was fixed to the recipient socket with an osteosynthesis screw and splinted with a double resin wire for 8 weeks. At the 6-month follow-up, the screw was removed, and the stability of the tooth and the regeneration obtained throughout the vestibular area were confirmed. At the 2-year follow-up, the transplanted tooth was asymptomatic and maintained a normal bone level. Advantages of autotransplantation over dental implants include maintenance of proprioception, possible orthodontic movements, and a relatively low cost. This case report demonstrates that an autotransplantation of a third molar attached to its buccal cortical plate is a viable option to replace teeth with a VRF. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Functional constraints on tooth morphology in carnivorous mammals

PubMed Central

2012-01-01

Background The range of potential morphologies resulting from evolution is limited by complex interacting processes, ranging from development to function. Quantifying these interactions is important for understanding adaptation and convergent evolution. Using three-dimensional reconstructions of carnivoran and dasyuromorph tooth rows, we compared statistical models of the relationship between tooth row shape and the opposing tooth row, a static feature, as well as measures of mandibular motion during chewing (occlusion), which are kinetic features. This is a new approach to quantifying functional integration because we use measures of movement and displacement, such as the amount the mandible translates laterally during occlusion, as opposed to conventional morphological measures, such as mandible length and geometric landmarks. By sampling two distantly related groups of ecologically similar mammals, we study carnivorous mammals in general rather than a specific group of mammals. Results Statistical model comparisons demonstrate that the best performing models always include some measure of mandibular motion, indicating that functional and statistical models of tooth shape as purely a function of the opposing tooth row are too simple and that increased model complexity provides a better understanding of tooth form. The predictors of the best performing models always included the opposing tooth row shape and a relative linear measure of mandibular motion. Conclusions Our results provide quantitative support of long-standing hypotheses of tooth row shape as being influenced by mandibular motion in addition to the opposing tooth row. Additionally, this study illustrates the utility and necessity of including kinetic features in analyses of morphological integration. PMID:22899809

Analysis of tooth brushing cycles.

PubMed

Tosaka, Yuki; Nakakura-Ohshima, Kuniko; Murakami, Nozomi; Ishii, Rikako; Saitoh, Issei; Iwase, Yoko; Yoshihara, Akihiro; Ohuchi, Akitsugu; Hayasaki, Haruaki

2014-11-01

The aim of this study was to demonstrate the effectiveness of an analysis of tooth brushing cycles using a system that measures tooth brushing motion and brushing force with an accelerometer and strain tension gage attached to a toothbrush. Mechanical plaque removal with a manual toothbrush remains the primary method of maintaining good oral hygiene for the majority of the population. Because toothbrush motion has not been fully understood, it should be clarified by analysis of tooth brushing cycles. Twenty healthy female dental hygienists participated in this study. Their tooth brushing motions were measured and analyzed using an American Dental Association-approved manual toothbrush to which a three-dimensional (3-D) accelerometer and strain tension gage were attached. 3-D motion and brushing force on the labial surface of the mandibular right central incisor and the lingual surface of the mandibular left first molar were measured, analyzed, and compared. Multilevel linear model analysis was applied to estimate variables and compare motion and forces related to the two tooth surfaces. The analysis of tooth brushing cycles was feasible, and significant differences were detected for durations and 3-D ranges of toothbrush motion as well as brushing force between the two tooth surfaces. The analysis used in this study demonstrated an ability to detect characteristics of tooth brushing motion, showing tooth brushing motion to change depending on the brushed location. These results also suggest that more detailed instructions might be required according to patient's oral condition.

Survey on Restoration of Endodontically Treated Anterior Teeth: A Questionnaire Based Study

PubMed Central

Ratnakar, P; Bhosgi, Rashmi; Metta, Kiran Kumar; Aggarwal, Kanika; Vinuta, S; Singh, Navneet

2014-01-01

Background: The aim of endodontic and restorative dentistry is the conservation of natural tooth structure. Endodontically treated tooth (ETT) undergoes loss of tooth structure and changes in physical characteristics. Therefore, proper selection of restoration for ETT is mandatory. The clinical approach of restoring ETT needs taking into considerations several issues. However, the best way to restore teeth after root canal treatment has long been and still a controversial subject to debate. Therefore, this study was carried out to detect the frequency of preferred methods of restoring ETT under different conditions. Materials and Methods: A questionnaire was framed and distributed among prosthodontists, endodontist and general practitioners of north India region to find out the frequency of best suitable material and method regarding restoration of ETT. 220 questionnaires were sent by electronic mail out of which 110 were received back. The questionnaire contained different methods of restoration of endodontically treated anterior teeth at different conditions (percentages) of remaining sound tooth structure. Respondents were asked to indicate their preferred method of restoration of those teeth. Results: Results showed that majority of respondents (51.82%) preferred to restore the tooth only with a tooth-color restorative material in condition A. In condition B, majority of respondents preferred to use tooth colored crown (44.55%) and prefabricated post and tooth colored restoration (24.5%). Whereas in condition C, most of the respondents preferred to use a cast post and core/crown (80.91%). Conclusion: From the findings of the present study, it can be concluded that the unrestored ETT is susceptible to fracture, which could lead to loss of tooth and that the maximum preservation of healthy tooth structure and use of restorative materials with mechanical properties similar to dental structure favor greater longevity of tooth restoration complex. PMID:25628482

Tooth movements in foxhounds after one or two alveolar corticotomies.

PubMed

Sanjideh, Payam A; Rossouw, P Emile; Campbell, Phillip M; Opperman, Lynne A; Buschang, Peter H

2010-02-01

The aim of this split-mouth experimental study was to determine (1) whether corticotomy procedures increase tooth movement and (2) the effects of a second corticotomy procedure after 4 weeks on the rate of tooth movement. The mandibular third and maxillary second premolars of five skeletally mature male foxhounds, approximately 2 years of age, were extracted. One randomly selected mandibular quadrant had buccal and lingual flaps and corticotomies performed around the second premolar; the other quadrant served as the control. Both maxillary quadrants had initial buccal flaps and corticotomies; one randomly selected quadrant had a second buccal flap surgery and corticotomy after 28 days. Coil springs (200 g force), along with a 0.045 mm diameter tube on a 0.040 mm diameter guiding wire, were used to move the mandibular second and maxillary third premolars. Records, including digital calliper measurements and radiographs, were taken on days 0, 10, 14, 28, 42, and 56. Multilevel statistical procedures were used to model longitudinal tooth movements. The radiographic measurements initially showed increasing mandibular tooth movement rates, peaking between 22 and 25 days, and then decelerating. Total mandibular tooth movements were significantly (P < 0.05) greater on the experimental (2.4 mm) than on the control (1.3 mm) side. The rates of maxillary tooth movement slowed over time, with significantly (P < 0.05) more overall tooth movement on the side that had two (2.3 mm) than one (2.0 mm) corticotomy procedure. Alveolar corticotomy significantly increases orthodontic tooth movement. Performing a second corticotomy procedure after 4 weeks maintained higher rates of tooth movement over a longer duration and produced greater overall tooth movement than performing just one initial corticotomy, but the difference was small.

Tooth Whitening: What We Now Know

PubMed Central

Carey, Clifton M.

2014-01-01

Declarative Title Current research about tooth whitening shows that it is safe and effective when manufacturer’s protocol is followed, yet there are risks of which the profession and users should be aware. This update provides a summary of current research and assessment of the safety and efficacy of tooth whitening regimens. Background Tooth whitening has become one of the most frequently requested dental procedures by the public. The public has come to demand whiter, more perfect smiles and in response many choices for tooth whitening have been made available. These include home-based products such as toothpastes, gels, and films, as well as in-office based systems where products containing highly concentrated bleaching agents are applied under professional supervision. The profession and public have been aware of certain risks related to tooth whitening such as increased tooth sensitivity and gingival irritation. New research has shown that there are other risks such as tooth surface roughening and softening, increased potential for demineralization, degradation of dental restorations, and unacceptable color change of dental restorations. The new research is also focused on optimizing whitening procedures to reduce tooth sensitivity and to increase the persistence of the whitening. Methods Current reports in the literature are reviewed that are related to the use of peroxide based whitening methods. These reports include in vitro studies for method optimization and mechanism as well as clinical studies on effects of various whitening regimens. Conclusions When manufacturer’s instructions are followed, hydrogen peroxide and carbamide peroxide based tooth whitening is safe and effective. Patients should be informed of the risks associated with tooth whitening and instructed on identification of adverse occurrences so that they may seek professional help asneeded. PMID:24929591

Wnt signaling during tooth replacement in zebrafish (Danio rerio): pitfalls and perspectives

PubMed Central

Huysseune, Ann; Soenens, Mieke; Elderweirdt, Fien

2014-01-01

The canonical (β-catenin dependent) Wnt signaling pathway has emerged as a likely candidate for regulating tooth replacement in continuously renewing dentitions. So far, the involvement of canonical Wnt signaling has been experimentally demonstrated predominantly in amniotes. These studies tend to show stimulation of tooth formation by activation of the Wnt pathway, and inhibition of tooth formation when blocking the pathway. Here, we report a strong and dynamic expression of the soluble Wnt inhibitor dickkopf1 (dkk1) in developing zebrafish (Danio rerio) tooth germs, suggesting an active repression of Wnt signaling during morphogenesis and cytodifferentiation of a tooth, and derepression of Wnt signaling during start of replacement tooth formation. To further analyse the role of Wnt signaling, we used different gain-of-function approaches. These yielded disjunct results, yet none of them indicating enhanced tooth replacement. Thus, masterblind (mbl) mutants, defective in axin1, mimic overexpression of Wnt, but display a normally patterned dentition in which teeth are replaced at the appropriate times and positions. Activating the pathway with LiCl had variable outcomes, either resulting in the absence, or the delayed formation, of first-generation teeth, or yielding a regular dentition with normal replacement, but no supernumerary teeth or accelerated tooth replacement. The failure so far to influence tooth replacement in the zebrafish by perturbing Wnt signaling is discussed in the light of (i) potential technical pitfalls related to dose- or time-dependency, (ii) the complexity of the canonical Wnt pathway, and (iii) species-specific differences in the nature and activity of pathway components. Finally, we emphasize the importance of in-depth knowledge of the wild-type pattern for reliable interpretations. It is hoped that our analysis can be inspiring to critically assess and elucidate the role of Wnt signaling in tooth development in polyphyodonts. PMID:25339911

Complex patterns of tooth replacement revealed in the fruit bat (Eidolon helvum).

PubMed

Popa, Elena M; Anthwal, Neal; Tucker, Abigail S

2016-12-01

How teeth are replaced during normal growth and development has long been an important question for comparative and developmental anatomy. Non-standard model animals have become increasingly popular in this field due to the fact that the canonical model laboratory mammal, the mouse, develops only one generation of teeth (monophyodonty), whereas the majority of mammals possess two generations of teeth (diphyodonty). Here we used the straw-coloured fruit bat (Eidolon helvum), an Old World megabat, which has two generations of teeth, in order to observe the development and replacement of tooth germs from initiation up to mineralization stages. Our morphological study uses 3D reconstruction of histological sections to uncover differing arrangements of the first and second-generation tooth germs during the process of tooth replacement. We show that both tooth germ generations develop as part of the dental lamina, with the first generation detaching from the lamina, leaving the free edge to give rise to a second generation. This separation was particularly marked at the third premolar locus, where the primary and replacement teeth become positioned side by side, unconnected by a lamina. The position of the replacement tooth, with respect to the primary tooth, varied within the mouth, with replacements forming posterior to or directly lingual to the primary tooth. Development of replacement teeth was arrested at some tooth positions and this appeared to be linked to the timing of tooth initiation and the subsequent rate of development. This study adds an additional species to the growing body of non-model species used in the study of tooth replacement, and offers a new insight into the development of the diphyodont condition. © 2016 Anatomical Society.

The regulation of tooth morphogenesis is associated with epithelial cell proliferation and the expression of Sonic hedgehog through epithelial-mesenchymal interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishida, Kentaro; Murofushi, Mayumi; Nakao, Kazuhisa

2011-02-18

Research highlights: {yields} Bioengineered teeth regulated the contact area of epithelium and mesenchyme. {yields} The crown width is regulated by the contact area of the epithelium and mesenchyme. {yields} This regulation is associated with cell proliferation and Sonic hedgehog expression. {yields} The cusp number is correlated with the crown width of the bioengineered tooth. {yields} Cell proliferation and Shh expression areas regulate the tooth morphogenesis. -- Abstract: Ectodermal organs, such as the tooth, salivary gland, hair, and mammary gland, develop through reciprocal epithelial-mesenchymal interactions. Tooth morphologies are defined by the crown width and tooth length (macro-morphologies), and by the numbermore » and locations of the cusp and roots (micro-morphologies). In our current study, we report that the crown width of a bioengineered molar tooth, which was reconstructed using dissociated epithelial and mesenchymal cells via an organ germ method, can be regulated by the contact area between epithelial and mesenchymal cell layers. We further show that this is associated with cell proliferation and Sonic hedgehog (Shh) expression in the inner enamel epithelium after the germ stage has formed a secondary enamel knot. We also demonstrate that the cusp number is significantly correlated with the crown width of the bioengineered tooth. These findings suggest that the tooth micro-morphology, i.e. the cusp formation, is regulated after the tooth width, or macro-morphology, is determined. These findings also suggest that the spatiotemporal patterning of cell proliferation and the Shh expression areas in the epithelium regulate the crown width and cusp formation of the developing tooth.« less

Tooth brushing among 11- to 15-year-olds in Denmark: combined effect of social class and migration status.

PubMed

Bast, L S; Nordahl, H; Christensen, L B; Holstein, B E

2015-03-01

Regular tooth brushing in adolescence predicts stable tooth brushing habits later in life. Differences in tooth brushing habits by ethnic background and socioeconomic position have been suggested. We investigated migration status and social class in relation to infrequent tooth brushing both separately and combined. The study population was 11-15 year-olds chosen from a clustered random sample of schools. Univariate and multivariate logistic regression analyses estimated the separate and combined effects of migration status and social class on less than twice daily tooth brushing. 10,607 respondents: a response rate of 88.3%. Boys of lower social class had higher odds ratio (OR) of infrequent tooth brushing than girls: 1.98 (95% confidence interval 1.62-2.41) vs 1.80 (1.53-2.24). Immigrants and descendants had higher odds compared to adolescents of Danish origin: immigrant boys OR 1.39 (1.05-1.89), girls OR 1.92 (1.47-2.50); descendant boys OR 2.53 (1.97-3.27), girls OR 2.56 (2.02-3.35). Analyses of the combined effect of social class and migration status showed that the social gradient in tooth brushing habits observed among ethnic Danes cannot be found among groups of immigrants and descendants. The study shows that both non-Danish origin and low social class increases the risk of infrequent tooth brushing among school-aged children. The study calls for in depth analyses of the processes which influence young people's tooth brushing habits. Further, there is a need to strengthen the promotion of appropriate tooth brushing habits of minority and low social class youths.

Nonlinear dynamic model of a gear-rotor-bearing system considering the flash temperature

NASA Astrophysics Data System (ADS)

Gou, Xiangfeng; Zhu, Lingyun; Qi, Changjun

2017-12-01

The instantaneous flash temperature is an important factor for gears in service. To investigate the effect of the flash temperature of a tooth surface on the dynamics of the spur gear system, a modified nonlinear dynamic model of a gear-rotor-bearing system is established. The factors such as the contact temperature of the tooth surface, time-varying stiffness, tooth surface friction, backlash, the comprehensive transmission error and so on are considered. The flash temperature of a tooth surface of pinion and gear is formulated according to Blok's flash temperature theory. The mathematical expression of the contact temperature of the tooth surface varied with time is derived and the tooth profile deformation caused by the change of the flash temperature of the tooth surface is calculated. The expression of the mesh stiffness varied with the flash temperature of the tooth surface is derived based on Hertz contact theory. The temperature stiffness is proposed and added to the nonlinear dynamic model of the system. The influence of load on the flash temperature of the tooth surface is analyzed in the parameters plane. The variation of the flash temperature of the tooth surface is studied. The numerical results indicate that the calculated method of the flash temperature of the gear tooth surface is effective and it can reflect the rules for the change of gear meshing temperature and sliding of the gear tooth surface. The effects of frequency, backlash, bearing clearance, comprehensive transmission error and time-varying stiffness on the nonlinear dynamics of the system are analyzed according to the bifurcation diagrams, Top Lyapunov Exponent (TLE) spectrums, phase portraits and Poincaré maps. Some nonlinear phenomena such as periodic bifurcation, grazing bifurcation, quasi-periodic bifurcation, chaos and its routes to chaos are investigated and the critical parameters are identified. The results provide an understanding of the system and serve as a useful reference in designing such systems.

The prevalence and risk indicators of tooth wear in 12- and 15-year-old adolescents in Central China.

PubMed

Zhang, Jing; Du, Yangge; Wei, Zhao; Tai, Baojun; Jiang, Han; Du, Minquan

2015-10-09

Tooth wear has been investigated in numerous countries, and the prevalence has varied. However, the data on tooth wear in China are scarce. The aim of this study was to describe the prevalence of tooth wear and to investigate the relative indicators associated with tooth wear in 12- and 15-year-old adolescents in Wuhan City, Hubei Province, Central China. A cross-sectional descriptive study was undertaken among 720 adolescents in Hubei Province, Central China. The age groups in this study were 12- and 15-year-old, and each group consisted of 360 participants in which females and males represented 50 % each. A modified version of the Basic Erosive Wear Examination (BEWE) tooth wear index was used for the buccal, cervical, occlusal/incisal and lingual surfaces of all of the teeth in the 720 adolescents. All of the participants were asked to answer a questionnaire consisting of questions about their current and historical dietary habits and oral hygiene. The prevalence of tooth wear was 18.6 and 89.4 % in 12- and 15-year-old adolescents, respectively. The prevalence rates of dentin exposure were 1.9 and 5.6 %, respectively. A significantly higher prevalence of tooth wear and dentin exposure in 15-year-old adolescents was found than in 12-year-old adolescents (p < 0.001 and p = 0.011). Several factors such as drinking soft drinks and fruit juices immediately after sports, taking aspirin, reflux, unilateral chewing, tooth brushing once daily or less often, duration of brushing less than 2 min and swimming in the summer were found to be associated with tooth wear. Tooth wear in 12- and 15-year-old adolescents in Central China is a significant problem and should receive greater attention. The prevalence of tooth wear increases with age and associated with socio-behavioral risk factors.

A study on the reproducibility and spatial uniformity of N-isopropylacrylamide polymer gel dosimetry using a commercial 10X fast optical-computed tomography scanner

NASA Astrophysics Data System (ADS)

Chang, Y. J.; Lin, J. Q.; Hsieh, B. T.; Chen, C. H.

2013-06-01

This study investigated the reproducibility and spatial uniformity of N-isopropylacrylamide (NIPAM) polymer gel as well as the reproducibility of a NIPAM polymer gel dosimeter. A commercial 10X fast optical computed tomography scanner (OCTOPUS-10X, MGS Research, Inc., Madison, CT, USA) was used as the readout tool of the NIPAM polymer gel dosimeter. A cylindrical NIPAM gel phantom measuring 10 cm (diameter) by 10 cm (height) by 3 mm (thickness) was irradiated by the four-field box treatment with a field size of 3 cm × 3 cm. The dose profiles were found to be consistent at the depths of 2.0 cm to 5.0 cm for two independent gel phantom batches, and the average uncertainty was less than 2%. The gamma pass rates were calculated to be between 94% and 95% at depths of 40 mm for two independent gel phantom batches using 4% dose difference and 4 mm distance-to-agreement criterion. The NIPAM polymer gel dosimeter was highly reproducible and spatially uniform. The results highlighted the potential of the NIPAM polymer gel dosimeter in radiotherapy.

Zombie Vortex Instability: Effects of Non-uniform Stratification & Thermal Cooling

NASA Astrophysics Data System (ADS)

Barranco, Joseph; Pei, Suyang; Marcus, Phil; Jiang, Chung-Hsiang

2015-11-01

The Zombie Vortex Instability (ZVI) is a nonlinear instability in rotating, stratified, shear flows, such as in protoplanetary disks (PPD) of gas and dust orbiting new stars. The instability mechanism is the excitation of baroclinic critical layers, leading to vorticity amplification and nonlinear evolution into anticyclonic vortices and cyclonic sheets. ZVI is most robust when the Coriolis frequency, shear rate, and Brunt-Väisälä (BV) frequency are of the same order. Previously, we investigated ZVI with uniform stratification and without thermal cooling. Here, we explore the role of non-uniform stratification as would be found in PPDs in which the BV frequency is zero in the disk midplane, and increases away from the midplane. We find that ZVI is vigorous 1-3 pressure scale heights away from the midplane, but the non-isotropic turbulence generated by ZVI can penetrate into the midplane. We also explore the effect of thermal cooling and find that ZVI is still robust for cooling times as short as 5 orbital periods. ZVI may play important roles in transporting angular momentum in PPDs, and in trapping dust grains, which may trigger gravitational clumping into planetesimals.

Periodontal profile classes predict periodontal disease progression and tooth loss.

PubMed

Morelli, Thiago; Moss, Kevin L; Preisser, John S; Beck, James D; Divaris, Kimon; Wu, Di; Offenbacher, Steven

2018-02-01

Current periodontal disease taxonomies have limited utility for predicting disease progression and tooth loss; in fact, tooth loss itself can undermine precise person-level periodontal disease classifications. To overcome this limitation, the current group recently introduced a novel patient stratification system using latent class analyses of clinical parameters, including patterns of missing teeth. This investigation sought to determine the clinical utility of the Periodontal Profile Classes and Tooth Profile Classes (PPC/TPC) taxonomy for risk assessment, specifically for predicting periodontal disease progression and incident tooth loss. The analytic sample comprised 4,682 adult participants of two prospective cohort studies (Dental Atherosclerosis Risk in Communities Study and Piedmont Dental Study) with information on periodontal disease progression and incident tooth loss. The PPC/TPC taxonomy includes seven distinct PPCs (person-level disease pattern and severity) and seven TPCs (tooth-level disease). Logistic regression modeling was used to estimate relative risks (RR) and 95% confidence intervals (CI) for the association of these latent classes with disease progression and incident tooth loss, adjusting for examination center, race, sex, age, diabetes, and smoking. To obtain personalized outcome propensities, risk estimates associated with each participant's PPC and TPC were combined into person-level composite risk scores (Index of Periodontal Risk [IPR]). Individuals in two PPCs (PPC-G: Severe Disease and PPC-D: Tooth Loss) had the highest tooth loss risk (RR = 3.6; 95% CI = 2.6 to 5.0 and RR = 3.8; 95% CI = 2.9 to 5.1, respectively). PPC-G also had the highest risk for periodontitis progression (RR = 5.7; 95% CI = 2.2 to 14.7). Personalized IPR scores were positively associated with both periodontitis progression and tooth loss. These findings, upon additional validation, suggest that the periodontal/tooth profile classes and the derived personalized propensity scores provide clinical periodontal definitions that reflect disease patterns in the population and offer a useful system for patient stratification that is predictive for disease progression and tooth loss. © 2018 American Academy of Periodontology.

Endodontic treatment of a maxillary lateral incisor with a perforating internal resorption by using cone beam computed tomography as a diagnostic aid: a case report.

PubMed

Takita, Toshiya; Tsurumachi, Tamotsu; Ogiso, Bunnai

2011-10-01

This case report presents the endodontic treatment of a maxillary right lateral incisor with a perforating internal resorption in a 50-year-old woman. Radiographically, internal resorption appears as a fairly uniform, radiolucent enlargement of the pulp canal and distortion of the original root canal outline. The use of cone beam computed tomography can help the clinician in making a confirmatory diagnosis and determining the treatment plan before undertaking the actual treatment. After cleaning the root canal space and the resorptive defect by mechanic instrumentation, irrigation, and interim calcium hydroxide dressing, the apical third canal was filled with a gutta-percha point by lateral condensation. The resorptive defect was filled with mineral trioxide aggregate. Follow-up radiographs at 3 years showed adequate repair of the resorption, and the tooth remained asymptomatic.

Energy Levels in Quantum Wells.

NASA Astrophysics Data System (ADS)

Zang, Jan Xin

Normalized analytical equations for eigenstates of an arbitrary one-dimensional configuration of square potentials in a well have been derived. The general formulation is used to evaluate the energy levels of a particle in a very deep potential well containing seven internal barriers. The configuration can be considered as a finite superlattice sample or as a simplified model for a sample with only several atom layers. The results are shown in graphical forms as functions of the height and width of the potential barriers and as functions of the ratio of the effective mass in barrier to the mass in well. The formation of energy bands and surface eigenstates from eigenstates of a deep single well, the coming close of two energy bands and a surface state which are separate ordinarily, and mixing of the wave function of a surface state with the bulk energy bands are seen. Then the normalized derivation is extended to study the effect of a uniform electric field applied across a one-dimensional well containing an internal configuration of square potentials The general formulation is used to calculate the electric field dependence of the energy levels of a deep well with five internal barriers. Typical results are shown in graphical forms as functions of the barrier height, barrier width, barrier effective mass and the field strength. The formation of Stark ladders and surface states from the eigenstates of a single deep well in an electric field, the localization process of wave functions with changing barrier height, width, and field strength and their anticrossing behaviors are seen. The energy levels of a hydrogenic impurity in a uniform medium and in a uniform magnetic field are calculated with variational methods. The energy eigenvalues for the eigenstates with major quantum number less than or equal to 3 are obtained. The results are consistent with previous results. Furthermore, the energy levels of a hydrogenic impurity at the bottom of a one-dimensional parabolic quantum well with a magnetic field normal to the plane of the well are calculated with the finite-basis-set variational method. The limit of small radial distance and the limit of great radial distance are considered to choose a set of proper basis functions. It is found that the energy levels increase with increasing parabolic parameter alpha and increase with increasing normalized magnetic field strength gamma except those levels with magnetic quantum number m < 0 at small gamma.

21 CFR 872.3910 - Backing and facing for an artificial tooth.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Backing and facing for an artificial tooth. 872.3910 Section 872.3910 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... artificial tooth. (a) Identification. A backing and facing for an artificial tooth is a device intended for...

The management of anterior tooth wear using gold palatal veneers in canine guidance.

PubMed

Eliyas, S; Martin, N

2013-03-01

Localised anterior tooth wear can be managed using minimally invasive techniques with conservation of tooth structure and preservation of pulp vitality. This article describes and illustrates with two clinical cases, the management of localised tooth wear, with the restoration of canine guidance by a combination of gold palatal veneers and direct composite restorations.

Computer-aided design of bevel gear tooth surfaces

NASA Technical Reports Server (NTRS)

Shuo, Hung Chang; Huston, Ronald L.; Coy, John J.

1989-01-01

This paper presents a computer-aided design procedure for generating bevel gears. The development is based on examining a perfectly plastic, cone-shaped gear blank rolling over a cutting tooth on a plane crown rack. The resulting impression on the plastic gear blank is the envelope of the cutting tooth. This impression and envelope thus form a conjugate tooth surface. Equations are presented for the locus of points on the tooth surface. The same procedures are then extended to simulate the generation of a spiral bevel gear. The corresponding governing equations are presented.

Computer aided design of bevel gear tooth surfaces

NASA Technical Reports Server (NTRS)

Chang, S. H.; Huston, R. L.; Coy, J. J.

1989-01-01

This paper presents a computer-aided design procedure for generating bevel gears. The development is based on examining a perfectly plastic, cone-shaped gear blank rolling over a cutting tooth on a plane crown rack. The resulting impression on the plastic gear blank is the envelope of the cutting tooth. This impression and envelope thus form a conjugate tooth surface. Equations are presented for the locus of points on the tooth surface. The same procedures are then extended to simulate the generation of a spiral bevel gear. The corresponding governing equations are presented.

Pseudochaos and anomalous transport: A study on saw-tooth map

NASA Astrophysics Data System (ADS)

Fan, Rong

The observation of chaotic dynamics in digital filter in late 1980s propelled the interest in piecewise linear map beyond the border of theoretical electrical engineering. Also, during last two decades, various physical models and phenomena, such as stochastic web and sticky orbits, not only broadened our knowledge of chaos but also urged us to further our understanding of meaning of chaos and randomness. In this dissertation, a piecewise linear kicked oscillator model: saw-tooth map, is studied as an example of pseudochaos. Physically, kicked oscillator model describes one-dimensional harmonic oscillator effected by delta-like kicks from external force source at certain fixed frequency. Starting from a special case of global periodicity, numerical investigations were carefully carried out in two cases that deviate from global periodicity. We observe the appearance of stochastic web structure and accompanying erratic dynamical behavior in the system that can't be fully explained by the classical Kolmogorov-Arnold-Moser theorem. Also anomalous transport occurs in both cases. We perform accurate analysis of Poincare recurrences and reconstruct the probability density function of Poincare recurrence times, which suggests a relation between the transport and the Poincare recurrence exponents. Saw-tooth map has non-uniform phase space, in which domains of regular dynamics and domains of chaotic dynamics are intertwined. The large-scale dynamics of the system is hugely impacted by the heterogeneity of the phase space, especially by the existence of hierarchy of periodic islands. We carefully study the characteristics of phase space and numerically compute fractal dimensions of the so-called exceptional set Delta in both cases. Our results suggest that the fractal dimension is strictly less than 2 and that the fractal structures are unifractal rather than multifractal. We present a phenomenological theoretical framework of Fractional Kinetic Equation (FKE) and Renormalization Group of Kinetics (RGK). FKE, which is fractional generalization of the Fokker-Planck-Kolmogorov equation, adopts the fractality of time and space and serves probabilistic description of chaos in Hamiltonian systems. RGK bridges the self-similar structure in phase space and large-scale behavior of the dynamics, and establishes relationships among fractality, transport and Poincare recurrences.

[Guided and computer-assisted implant surgery and prosthetic: The continuous digital workflow].

PubMed

Pascual, D; Vaysse, J

2016-02-01

New continuous digital workflow protocols of guided and computer-assisted implant surgery improve accuracy of implant positioning. The design of the future prosthesis is based on the available prosthetic space, gingival height and occlusal relationship with the opposing and adjacent teeth. The implant position and length depend on volume, density and bone quality, gingival height, tooth-implant and implant-implant distances, implant parallelism, axis and type of the future prosthesis. The crown modeled on the software will therefore serve as a guide to the future implant axis and not the reverse. The guide is made by 3D printing. The software determines surgical protocol with the drilling sequences. The unitary or plural prosthesis, modeled on the software and built before surgery, is loaded directly after implant placing, if needed. These protocols allow for a full continuity of the digital workflow. The software provides the surgeon and the dental technician a total freedom for the prosthetic-surgery guide design and the position of the implants. The prosthetic project, occlusal and aesthetic, taking the bony and surgical constraints into account, is optimized. The implant surgery is simplified and becomes less "stressful" for the patient and the surgeon. Guided and computer-assisted surgery with continuous digital workflow is becoming the technique of choice to improve the accuracy and quality of implant rehabilitation. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Structural optimization of dental restorations using the principle of adaptive growth.

PubMed

Couegnat, Guillaume; Fok, Siu L; Cooper, Jonathan E; Qualtrough, Alison J E

2006-01-01

In a restored tooth, the stresses that occur at the tooth-restoration interface during loading could become large enough to fracture the tooth and/or restoration and it has been estimated that 92% of fractured teeth have been previously restored. The tooth preparation process for a dental restoration is a classical optimization problem: tooth reduction must be minimized to preserve tooth tissue whilst stress levels must be kept low to avoid fracture of the restored unit. The objective of the present study was to derive alternative optimized designs for a second upper premolar cavity preparation by means of structural shape optimization based on the finite element method and biological adaptive growth. Three models of cavity preparations were investigated: an inlay design for preparation of a premolar tooth, an undercut cavity design and an onlay preparation. Three restorative materials and several tooth/restoration contact conditions were utilized to replicate the in vitro situation as closely as possible. The optimization process was run for each cavity geometry. Mathematical shape optimization based on biological adaptive growth process was successfully applied to tooth preparations for dental restorations. Significant reduction in stress levels at the tooth-restoration interface where bonding is imperfect was achieved using optimized cavity or restoration shapes. In the best case, the maximum stress value was reduced by more than 50%. Shape optimization techniques can provide an efficient and effective means of reducing the stresses in restored teeth and hence has the potential of prolonging their service lives. The technique can easily be adopted for optimizing other dental restorations.

Dental Cell Sheet Biomimetic Tooth Bud Model

PubMed Central

Monteiro, Nelson; Smith, Elizabeth E.; Angstadt, Shantel; Zhang, Weibo; Khademhosseini, Ali

2016-01-01

Tissue engineering and regenerative medicine technologies offer promising therapies for both medicine and dentistry. Our long-term goal is to create functional biomimetic tooth buds for eventual tooth replacement in humans. Here, our objective was to create a biomimetic 3D tooth bud model consisting of dental epithelial (DE) – dental mesenchymal (DM) cell sheets (CSs) combined with biomimetic enamel organ and pulp organ layers created using GelMA hydrogels. Pig DE or DM cells seeded on temperature-responsive plates at various cell densities (0.02, 0.114 and 0.228 cells 106/cm2) and cultured for 7, 14 and 21 days were used to generate DE and DM cell sheets, respectively. Dental CSs were combined with GelMA encapsulated DE and DM cell layers to form bioengineered 3D tooth buds. Biomimetic 3D tooth bud constructs were cultured in vitro, or implanted in vivo for 3 weeks. Analyses were performed using micro-CT, H&E staining, polarized light (Pol) microscopy, immunofluorescent (IF) and immunohistochemical (IHC) analyses. H&E, IHC and IF analyses showed that in vitro cultured multilayered DE-DM CSs expressed appropriate tooth marker expression patterns including SHH, BMP2, RUNX2, tenascin and syndecan, which normally direct DE-DM interactions, DM cell condensation, and dental cell differentiation. In vivo implanted 3D tooth bud constructs exhibited mineralized tissue formation of specified size and shape, and SHH, BMP2 and RUNX2and dental cell differentiation marker expression. We propose our biomimetic 3D tooth buds as models to study optimized DE-DM cell interactions leading to functional biomimetic replacement tooth formation. PMID:27565550

Relationship and inter observer agreement of tooth and face forms in a Saudi subpopulation.

PubMed

Habib, Syed Rashid; Shiddi, Ibraheem Al; Al-Sufyani, Mohammed D; Althobaiti, Fahad A

2015-04-01

To determine the relationship of tooth form with the face form by different observers and further investigate the inter observer agreement on tooth forms, face forms, their relationship among male Saudis. A comparative cross-sectional study. Department of Prosthodontics, College of Dentistry, King Saud University, Riyadh, KSA, from February till August 2013. Ninety four male participants aged 18 - 35 years were randomly recruited for the study. Full-face and anterior teeth (intraoral) digital photographs in the frontal plane were recorded. The outline tracings of the face and the tooth were obtained using Autocad (version 2010) software. The outline of the tooth was enlarged proportionately, without altering the length to width ratio to fit the face outline. The outlines were then evaluated visually by 6 prosthodontists and results were tabulated. The most common type of face form (49.65%) and tooth form (56.38%) was square tapering. Using the visual method, a good relationship (31.41%), moderate relationship (35.31%), weak relationship (19.68%) and no relationship (13.65%) between the tooth form and face form was found by the observers. Overall kappa for inter observer agreement on face form, tooth form and their relationship was 0.24, 0.17 and 0.26 respectively. The kappa values showed a fair agreement between the observers. The study results indicated that there was no highly defined relationship between the tooth form and face form in the studied Saudi subpopulation. A fair agreement was found between the observers for classifying the tooth forms, face froms and their relationship.

Investigation of tooth transposition in a non-syndromic Turkish anatolian population: characteristic features and associated dental anomalies.

PubMed

Celikoglu, Mevlut; Miloglu, Ozkan; Oztek, Ozkan

2010-09-01

The aims of this study were to investigate the frequency and characteristics of dental transpositions and to evaluate associated dental anomalies in a large sample of Turkish Anatolian population. A retrospective study was performed using panoramic radiographs of 6983 patients (4092 females and 2891 males) ranging in age from 12 to 27 subjected to Faculty of Dentistry at the University of Ataturk (Erzurum, Turkey) between 2005 and 2008. For each patient with tooth transposition we recorded the demographic variables (including age, sex), history of trauma, type, classification, and location of tooth transpositions, and associated dental anomalies. The Pearson chi-squared test was used to determine potential differences in the distribution of tooth transposition when stratified by gender. Tooth transposition was detected in 19 subjects (0.27%), with a 2.2:1 female male ratio (P=0.38). The most commonly observed transposition was maxillary canine-lateral incisor (60%). The frequencies of complete and incomplete transpositions were equal (10/10) and it was more common in the left side than in the right side (11/9). Of the 19 subjects, 10.5% had a peg shaped lateral incisor, 21.1% one congenitally missing tooth excluding third molar. Supernumerary tooth, impacted teeth excluding third molars, transmigrated tooth, and dilacerations were also observed. The frequency of tooth transposition was 0.27% in a Turkish Anatolian population and maxillary canine-lateral incisor was the most frequently observed transposition. Retained primary teeth were the most frequently observed dental anomaly in all types of tooth transposition.

Comparison of Three types of Tooth Brushes on Plaque and Gingival Indices: A Randomized Clinical Trial.

PubMed

Moeintaghavi, Amir; Sargolzaie, Naser; Rostampour, Mehrnoosh; Sarvari, Sara; Kargozar, Sanaz; Gharaei, Shideh

2017-01-01

To compare clinical results of three types of manual tooth brushes on plaque removal efficacy and gingivitis. This study is a single blind randomized trial with crossover design which involved 30 periodontaly healthy individuals. Professional plaque removal and oral hygiene instruction were performed for all the participants in the first step of our study followed by asking them to avoid brushing for 2 days. Thereafter plaque and gingivitis scores were measured using plaque and gingival indices (PI and GI). Then subjects were instructed to use Pulsar tooth brush for a two-week period and then, GI and PI indices were assessed again. After passing one-week period for wash out, subjects didn't brush for 2 days and indices were recorded again. The same procedure was done for CrossAction, and Butler 411 tooth brushes respectively and at the end of the study these variables were analyzed using SPSS software ver.16. Repeated measurement ANOVA test was used to compare the scores between different brushes. Finding of this study reveals that using all three types of tooth brushes resulted in significant plaque and gingivitis reduction compared to baseline levels. Pulsar tooth brush was significantly more effective in diminishing PI and GI than Butler tooth brush (p=0.044 and 0.031 respectively). According to our findings all 3 types of tooth brushes are effective in reduction of plaque and gingivitis and this reduction is significantly greater for Pulsar tooth brush compared to Butler and CrossAction tooth brushes.

Sox2 marks epithelial competence to generate teeth in mammals and reptiles

PubMed Central

Juuri, Emma; Jussila, Maria; Seidel, Kerstin; Holmes, Scott; Wu, Ping; Richman, Joy; Heikinheimo, Kristiina; Chuong, Cheng-Ming; Arnold, Katrin; Hochedlinger, Konrad; Klein, Ophir; Michon, Frederic; Thesleff, Irma

2013-01-01

Tooth renewal is initiated from epithelium associated with existing teeth. The development of new teeth requires dental epithelial cells that have competence for tooth formation, but specific marker genes for these cells have not been identified. Here, we analyzed expression patterns of the transcription factor Sox2 in two different modes of successional tooth formation: tooth replacement and serial addition of primary teeth. We observed specific Sox2 expression in the dental lamina that gives rise to successional teeth in mammals with one round of tooth replacement as well as in reptiles with continuous tooth replacement. Sox2 was also expressed in the dental lamina during serial addition of mammalian molars, and genetic lineage tracing indicated that Sox2+ cells of the first molar give rise to the epithelial cell lineages of the second and third molars. Moreover, conditional deletion of Sox2 resulted in hyperplastic epithelium in the forming posterior molars. Our results indicate that the Sox2+ dental epithelium has competence for successional tooth formation and that Sox2 regulates the progenitor state of dental epithelial cells. The findings imply that the function of Sox2 has been conserved during evolution and that tooth replacement and serial addition of primary teeth represent variations of the same developmental process. The expression patterns of Sox2 support the hypothesis that dormant capacity for continuous tooth renewal exists in mammals. PMID:23462476

Promoting positive health behaviours--'tooth worm' phenomenon and its implications.

PubMed

Gao, X L; Hsu, C Y S; Xu, Y C; Loh, T; Koh, D; Hwarng, H B

2012-03-01

'Tooth worm' is a traditional belief about the pathogen of dental caries (tooth decay). Nevertheless, in our previous study, parental 'tooth worm' belief was linked to a reduced caries risk of their children. This study aimed to further characterize the impact of parental 'tooth worm' belief on their children's caries experience and its psychobehavioural mechanisms. analytic observational study. Thirteen randomly selected kindergartens in Singapore. 1,782 preschoolers aged 3-6 years. Each child received an oral examination and microbiological tests. Parents completed a self-administered questionnaire on their socio-demographic background, oral health knowledge/attitude and child's oral health habits. Multivariate analysis confirmed a reduced chance of 'high caries rate' (number of affected teeth > 2) among children whose parents held the 'tooth worm' belief (Odds Ratio = 0.41; 95% Confidence Interval = 0.19-0.89). With such perception among parents, children brushed their teeth more frequently (p = 0.042). Since no difference in oral hygiene was observed, the health benefit of the "tooth worm" perception may be acquired through the delivery of fluoride (an agent with proven anti-caries effect) during frequent toothbrushing episodes. This study revealed a 'tooth worm' phenomenon, indicating that parental 'tooth worm' belief is associated with early establishment of regular toothbrushing habit and reduction of dental caries in children. This phenomenon and its psychobehavioural mechanisms, enriching our understanding of oral health behaviours, have implications for effective health education.

Whole-Exome Sequencing Identifies Novel Variants for Tooth Agenesis.

PubMed

Dinckan, N; Du, R; Petty, L E; Coban-Akdemir, Z; Jhangiani, S N; Paine, I; Baugh, E H; Erdem, A P; Kayserili, H; Doddapaneni, H; Hu, J; Muzny, D M; Boerwinkle, E; Gibbs, R A; Lupski, J R; Uyguner, Z O; Below, J E; Letra, A

2018-01-01

Tooth agenesis is a common craniofacial abnormality in humans and represents failure to develop 1 or more permanent teeth. Tooth agenesis is complex, and variations in about a dozen genes have been reported as contributing to the etiology. Here, we combined whole-exome sequencing, array-based genotyping, and linkage analysis to identify putative pathogenic variants in candidate disease genes for tooth agenesis in 10 multiplex Turkish families. Novel homozygous and heterozygous variants in LRP6, DKK1, LAMA3, and COL17A1 genes, as well as known variants in WNT10A, were identified as likely pathogenic in isolated tooth agenesis. Novel variants in KREMEN1 were identified as likely pathogenic in 2 families with suspected syndromic tooth agenesis. Variants in more than 1 gene were identified segregating with tooth agenesis in 2 families, suggesting oligogenic inheritance. Structural modeling of missense variants suggests deleterious effects to the encoded proteins. Functional analysis of an indel variant (c.3607+3_6del) in LRP6 suggested that the predicted resulting mRNA is subject to nonsense-mediated decay. Our results support a major role for WNT pathways genes in the etiology of tooth agenesis while revealing new candidate genes. Moreover, oligogenic cosegregation was suggestive for complex inheritance and potentially complex gene product interactions during development, contributing to improved understanding of the genetic etiology of familial tooth agenesis.

Natural Tooth Pontic: An Instant Esthetic Option for Periodontally Compromised Teeth—A Case Series

PubMed Central

Raj, Rishi; Narayan, Ipshita; Gowda, Triveni Mavinakote; Mehta, D. S.

2016-01-01

Sudden tooth loss in the esthetic zone of the maxillary or mandibular anterior region can be due to trauma, periodontal disease, or endodontic failure. The treatment options for replacing the missing tooth can vary between removable prosthesis, tooth-supported prosthesis, and implant-supported prosthesis. Irrespective of the final treatment, the first line of management would be to provisionally restore the patient's esthetic appearance at the earliest, while functionally stabilizing the compromised arch. Using the patient's own natural tooth as a pontic offers the benefits of being the right size, shape, and color and provides exact repositioning in its original intraoral three-dimensional position. Additionally, using the patient's platelet concentrate (platelet rich fibrin) facilitates early wound healing and preservation of alveolar ridge shape following tooth extraction. The abutment teeth can also be preserved with minimal or no preparation, thus keeping the technique reversible, and can be completed at the chair side thereby avoiding laboratory costs. This helps the patient better tolerate the effect of tooth loss psychologically. The article describes a successful, immediate, and viable technique for rehabilitation of three different patients requiring replacement of a single periodontally compromised tooth in an esthetic region. PMID:27994892

[Three-dimensional tooth model reconstruction based on fusion of dental computed tomography images and laser-scanned images].

PubMed

Zhang, Dongxia; Gan, Yangzhou; Xiong, Jing; Xia, Zeyang

2017-02-01

Complete three-dimensional(3D) tooth model provides essential information to assist orthodontists for diagnosis and treatment planning. Currently, 3D tooth model is mainly obtained by segmentation and reconstruction from dental computed tomography(CT) images. However, the accuracy of 3D tooth model reconstructed from dental CT images is low and not applicable for invisalign design. And another serious problem also occurs, i.e. frequentative dental CT scan during different intervals of orthodontic treatment often leads to radiation to the patients. Hence, this paper proposed a method to reconstruct tooth model based on fusion of dental CT images and laser-scanned images. A complete3 D tooth model was reconstructed with the registration and fusion between the root reconstructed from dental CT images and the crown reconstructed from laser-scanned images. The crown of the complete 3D tooth model reconstructed with the proposed method has higher accuracy. Moreover, in order to reconstruct complete 3D tooth model of each orthodontic treatment interval, only one pre-treatment CT scan is needed and in the orthodontic treatment process only the laser-scan is required. Therefore, radiation to the patients can be reduced significantly.

Impact of demographic, behavioral, and dental care utilization parameters on tooth color and personal satisfaction.

PubMed

Odioso, L L; Gibb, R D; Gerlach, R W

2000-01-01

A cross-sectional survey across broad age ranges was conducted to evaluate demographic, behavioral, and treatment parameters that impact tooth color and its perception. The sample included 180 US adults and teenagers, with a comparable representation of males and females in 6 different age strata, ranging from 13 to 64 years. Tooth color (L*a*b*) was measured on the maxillary central incisors using a spectrophotometer, and first-person satisfaction with tooth color was assessed using a five-point qualitative scale. Demographic, behavioral, and oral care parameters were modeled using multiple regression analysis. After adjusting for other explanatory variables, age, gender, coffee/tea consumption, and dental care all significantly affected yellowing (b*) and brightness (L*). Dental-visit frequency was the only factor that significantly predicted self-satisfaction with tooth color, explaining just 3% of the overall variability. First-person dissatisfaction with tooth color was common and found in most demographic and behavioral cohorts. Although age contributed to objectively measured tooth discoloration, personal satisfaction with tooth color was age-independent. These results suggest that the need or demand for esthetic dentistry may be broad-based and transcend stereotypical perceptions.

The timing of mandibular tooth formation in two African groups.

PubMed

Elamin, Fadil; Hector, Mark P; Liversidge, Helen M

2017-05-01

Ethnic differences in the timing of human tooth development are unclear. To describe similarities and differences in the timing of tooth formation in two groups of Sudanese children and young adults. The sample consisted of healthy individuals from Khartoum, Sudan, aged 2-23 years. The Northern group was of Arab origin (848 males, 802 females) and the Western group was of African origin (846 males, 402 females). Each mandibular left permanent tooth from first incisor to third molar was assessed from dental radiographs into one of 15 development stages. Mean ages at entry for 306 tooth stages were calculated using probit regression in males/females in each group and compared using a t-test. Mean ages were not significantly different in most tooth stage comparisons between ethnic groups for both males (61/75) and females (56/76), despite a tendency of earlier mean ages in the Western group. Mean ages for most tooth stage comparisons between males and females (137/155) were not significantly different within ethnic groups suggesting low sexual dimorphism. The mean ages of most mandibular tooth formation stages were generally not significantly different between ethnic groups or between males and females in this study.

Infrared light sensor applied to early detection of tooth decay

NASA Astrophysics Data System (ADS)

Benjumea, Eberto; Espitia, José; Díaz, Leonardo; Torres, Cesar

2017-08-01

The approach dentistry to dental care is gradually shifting to a model focused on early detection and oral-disease prevention; one of the most important methods of prevention of tooth decay is opportune diagnosis of decay and reconstruction. The present study aimed to introduce a procedure for early diagnosis of tooth decay and to compare result of experiment of this method with other common treatments. In this setup, a laser emitting infrared light is injected in core of one bifurcated fiber-optic and conduced to tooth surface and with the same bifurcated fiber the radiation reflected for the same tooth is collected and them conduced to surface of sensor that measures thermal and light frequencies to detect early signs of decay below a tooth surface, where demineralization is difficult to spot with x-ray technology. This device will can be used to diagnose tooth decay without any chemicals and rays such as high power lasers or X-rays.

Drilling Deeper into tooth brushing skills: Is proactive interference an under-recognized factor in oral hygiene behavior change?

PubMed

Thavarajah, Rooban; Kumar, Madan; Mohandoss, Anusa Arunachalam; Vernon, Lance T

2015-09-01

Proper tooth brushing is a seemingly simple motor activity that can promote oral health. Applying health theories, such as the Information-Motivation-Behavioral Skills (IMB) model, Motivational Interviewing (MI) and Integrated Health Coaching (IHC), may help optimize tooth brushing technique in those with suboptimal skills. Some motor activities, including tooth brushing, may over time become rote and unconscious actions, such that an existing habit can inhibit new learning, i.e., exert proactive interference on learning the new skill. Proactive interference may impede the acquisition of new tooth brushing skills; thus, in this report, we: (1) Review how the habit of tooth brushing is formed; (2) Postulate how proactive interference could impede the establishment of proper tooth brushing retraining; (3) Discuss the merits of this hypothesis; and (4) Provide guidance for future work in this topic within the context of an approach to behavior change that integrates IMB, MI and IHC methodology.

Drilling Deeper into tooth brushing skills: Is proactive interference an under-recognized factor in oral hygiene behavior change?

PubMed Central

Thavarajah, Rooban; Kumar, Madan; Mohandoss, Anusa Arunachalam

2015-01-01

Proper tooth brushing is a seemingly simple motor activity that can promote oral health. Applying health theories, such as the Information-Motivation-Behavioral Skills (IMB) model, Motivational Interviewing (MI) and Integrated Health Coaching (IHC), may help optimize tooth brushing technique in those with suboptimal skills. Some motor activities, including tooth brushing, may over time become rote and unconscious actions, such that an existing habit can inhibit new learning, i.e., exert proactive interference on learning the new skill. Proactive interference may impede the acquisition of new tooth brushing skills; thus, in this report, we: (1) Review how the habit of tooth brushing is formed; (2) Postulate how proactive interference could impede the establishment of proper tooth brushing retraining; (3) Discuss the merits of this hypothesis; and (4) Provide guidance for future work in this topic within the context of an approach to behavior change that integrates IMB, MI and IHC methodology. PMID:26457238

Altered tooth morphogenesis after silencing the planar cell polarity core component, Vangl2.

PubMed

Wu, Zhaoming; Epasinghe, Don Jeevanie; He, Jinquan; Li, Liwen; Green, David W; Lee, Min-Jung; Jung, Han-Sung

2016-12-01

Vangl2, one of the core components of the planar cell polarity (PCP) pathway, has an important role in the regulation of morphogenesis in several tissues. Although the expression of Vangl2 has been detected in the developing tooth, its role in tooth morphogenesis is not known. In this study, we show that Vangl2 is expressed in the inner dental epithelium (IDE) and in the secondary enamel knots (SEKs) of bell stage tooth germs. Inhibition of Vangl2 expression by siRNA treatment in in vitro-cultured tooth germs resulted in retarded tooth germ growth with deregulated cell proliferation and apoptosis. After kidney transplantation of Vangl2 siRNA-treated tooth germs, teeth were observed to be small and malformed. We also show that Vangl2 is required to maintain the proper pattern of cell alignment in SEKs, which maybe important for the function of SEKs as signaling centers. These results suggest that Vangl2 plays an important role in the morphogenesis of teeth.

Computer-aided design of tooth preparations for automated development of fixed prosthodontics.

PubMed

Yuan, Fusong; Sun, Yuchun; Wang, Yong; Lv, Peijun

2014-01-01

This paper introduces a method to digitally design a virtual model of a tooth preparation of the mandibular first molar, by using the commercial three-dimensional (3D) computer-aided design software packages Geomagic and Imageware, and using the model as an input to automatic tooth preparing system. The procedure included acquisition of 3D data from dentate casts and digital modeling of the shape of the tooth preparation components, such as the margin, occlusal surface, and axial surface. The completed model data were stored as stereolithography (STL) files, which were used in a tooth preparation system to help to plan the trajectory. Meanwhile, the required mathematical models in the design process were introduced. The method was used to make an individualized tooth preparation of the mandibular first molar. The entire process took 15min. Using the method presented, a straightforward 3D shape of a full crown can be obtained to meet clinical needs prior to tooth preparation. © 2013 Published by Elsevier Ltd.

Accuracy and precision of estimating age of gray wolves by tooth wear

USGS Publications Warehouse

Gipson, P.S.; Ballard, W.B.; Nowak, R.M.; Mech, L.D.

2000-01-01

We evaluated the accuracy and precision of tooth wear for aging gray wolves (Canis lupus) from Alaska, Minnesota, and Ontario based on 47 known-age or known-minimum-age skulls. Estimates of age using tooth wear and a commercial cementum annuli-aging service were useful for wolves up to 14 years old. The precision of estimates from cementum annuli was greater than estimates from tooth wear, but tooth wear estimates are more applicable in the field. We tended to overestimate age by 1-2 years and occasionally by 3 or 4 years. The commercial service aged young wolves with cementum annuli to within ?? 1 year of actual age, but under estimated ages of wolves ???9 years old by 1-3 years. No differences were detected in tooth wear patterns for wild wolves from Alaska, Minnesota, and Ontario, nor between captive and wild wolves. Tooth wear was not appropriate for aging wolves with an underbite that prevented normal wear or severely broken and missing teeth.

Influence of muscle pain tolerance on muscle pain threshold in experimental tooth clenching in man.

PubMed

Christensen, L V

1979-07-01

Ten adults and ten children exercised maximal voluntary tooth clenching until pains appeared in the jaw muscles, i.e. the muscle pain threshold of tooth clenching was determined. Subsequently, the subjects were instructed to exercise tooth clenching until they were forced to stop because of intolerable pains and exhaustion of the contracting muscles, i.e. the muscle pain tolerance of tooth clenching was recorded, and during these bouts of clenching the pain tolerance of tooth clenching was recorded, and during these bouts of clenching the pain threshold was also determined. In adults, determination of the pain tolerance decreased the pain threshold by 19%, and in children it either decreased the pain threshold by 20% or increased it by 56%. It is proposed to introduce the muscle pain tolerance of tooth clenching as an adjunct in the clinical examination of cases of facial pains presumed to originate from the jaw muscles, but the test should be interpreted with caution.

Diagnosing and treatment planning inadequate tooth display.

PubMed

Spear, F

2016-10-21

Some of the most challenging patients to produce a pleasing smile for are those who present with inadequate tooth display (either due to tooth position, the patient has normal size teeth, but they aren't exposed adequately to fill out the smile) or due to tooth size (the teeth are small, often due to tooth wear). The key to understanding how to manage these patients is to learn to understand the possible aetiologies that could produce the condition, and learn how to diagnose which aetiologies exist for your patient. Potential aetiologies for inadequate tooth display in patients with normal length unworn anterior teeth: excessive lip length; inadequate lip mobility; inadequate vertical eruption of the anterior teeth; inadequate facial prominence of the maxillary anterior teeth; vertical maxillary deficiency; and anterior maxillary deficiency.This article, the first in a British Dental Journal series on the topic of aesthetic dentistry, reviews the clinical findings consistent with diagnosing each of the above etiologies, and then reviews the treatment options available for correcting the inadequate tooth display.

Autogenous transplantation of mandibular third molar to replace tooth with vertical root fracture

PubMed Central

Asgary, Saeed

2009-01-01

Autogenous tooth transplantation (ATT) can be considered when there is a hopeless molar tooth and suitable donor present. This report presents an unconventional case of successful ATT of a third molar replacing the adjacent fractured second molar in a 33 year old woman. This wisdom tooth had completely developed roots. Root-end filling with Calcium Enriched Mixture (CEM) cement was performed in the third molar. The second molar was extracted non-traumatically without any bone removal; the wisdom tooth was immediately transplanted into the recipient socket. No endodontic treatment was carried out either during or after the ATT. At six-month and 2-year clinical examination the patient was asymptomatic; the transplanted tooth was still functional, with no evidence of marginal periodontal pathosis. At the same follow ups, radiographic evaluation illustrated bone regeneration, normal PDL, and absence of external root resorption. Transplantation of mature third molar seems to be a promising method for replacing a lost permanent molar tooth and restoring aesthetics and function. PMID:24003333

Toothaches

MedlinePlus

Pain - tooth or teeth ... A toothache is often the result of dental cavities (tooth decay) or an infection. Tooth decay is often caused by poor dental hygiene . It may also be partly inherited. Sometimes, pain ...

Interaction between attrition,abrasion and erosion in tooth wear.

PubMed

Addy, M; Shellis, R P

2006-01-01

Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence seems insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear through formation of pellicle and by remineralisation but cannot prevent it.

Organ dose conversions from ESR measurements using tooth enamel of atomic bomb survivors.

PubMed

Takahashi, Fumiaki; Sato, Kaoru

2012-03-01

Dose conversions were studied for dosimetry of atomic bomb survivors based upon electron spin resonance (ESR) measurements of tooth enamel. Previously analysed data had clarified that the tooth enamel dose could be much larger than other organ doses from a low-energy photon exposure. The radiation doses to other organs or whole-body doses, however, are assumed to be near the tooth enamel dose for photon energies which are dominant in the leakage spectrum of the Hiroshima atomic bomb assumed in DS02. In addition, the thyroid can be a candidate for a surrogate organ in cases where the tooth enamel dose is not available in organ dosimetry. This paper also suggests the application of new Japanese voxel phantoms to derive tooth enamel doses by numerical analyses.

Analysis of dental erosion induced by different beverages and validity of equipment for identifying early dental erosion, in vitro study.

PubMed

Jameel, Rafey Ahmad; Khan, Shah Salman; Abdul Rahim, Zubaidah Hj; Bakri, Marina Mohd; Siddiqui, Saima

2016-07-01

To understand early dental erosion induced by different beverages and the equipment for its detection. The study was conducted at the University Malaya Medical Centre, Kuala Lumpur, Malaysia, from June to September 2014, and comprised single-rooted, unpolished teeth divided into six groups. Electron micrographs and other baseline readings for further analyses were taken before and after the exposure to different beverages. The teeth were exposed to the beverages using a modified Nordini's artificial mouth model. The positioning of the teeth on the motorised stage of the equipment was standardised. Of the several beverages used, CocaCola had the lowest pH value of 2.53, while tap water had the highest pH of 5.4. Deionised distilled water, which was used as a reference, had a pH near to neutral /alkaline of 7.3. The fluoride content ranged between 9.38ppm in tea and 0.005ppm in orange juice. Teeth exposed to beverages with low pH and considerably high fluoride underwent slight remineralisation (roughness increase 8% from tea), while beverages with no fluoride content and low pH roughened the enamel surface (Coca Cola roughened upto 37%). Quantitative analyses of tooth erosion, micro-hardness, surface-roughness, and surface-height showed that all beverages exhibited positive erosive effect on the tooth enamel surface (p<0.005). CocaCola was found to be the most erosive agent among both hot and cold beverages (37%), while coffee was more erosive among the hot beverages (29%).

[Skeletal anchorage in the past, today and tomorrow].

PubMed

Melsen, Birte; Dalstra, Michel

2017-03-01

Skeletal anchorage was not introduced as an alternative to conventional anchorage modalities. The first skeletal anchorage was a ligature through a hole in the infrazygomatic crest. This was replaced by surgical screws and finally the TADs, which were optimized with respect to the material and morphology, were developed. A bracket-like head allows for the use of the mini-implant as indirect anchorage, but should not be a tool for lost control resulting from badly planned biomechanics or failing compliance. Skeletal anchorage should serve as an adjunct to correct biomechanics, to enable treatments that could not be performed prior to the introduction of skeletal anchorage. The aim of this study was to test the hypothesis that temporary anchorage mini-screws help maintain bone density, height and width of alveolar processes in the extraction sites, and thus prevent the thinning of the alveolar ridge usually observed. In adult patients with degenerated dentitions the application of skeletal anchorage can allow for the displacement of teeth where no anchorage units are present, but also for the redevelopment and maintenance of atrophic alveolar bone. The basis for the optimal use of skeletal anchorage is that the correct line of action for the desired tooth displacement is defined and the necessary force system constructed either with the skeletal anchorage as direct or as indirect anchorage. After a period, during which osseointegrated implants were used as anchorage for tooth movement and bone maintenance, it was accepted that the mini-implants could serve also as anchorage for skeletal displacements avoiding loading of teeth. © EDP Sciences, SFODF, 2017.

The effects of alveolar bone loss and miniscrew position on initial tooth displacement during intrusion of the maxillary anterior teeth: Finite element analysis

PubMed Central

Cho, Sun-Mi; Choi, Sung-Hwan; Sung, Sang-Jin; Yu, Hyung-Seog

2016-01-01

Objective The aim of this study was to determine the optimal loading conditions for pure intrusion of the six maxillary anterior teeth with miniscrews according to alveolar bone loss. Methods A three-dimensional finite element model was created for a segment of the six anterior teeth, and the positions of the miniscrews and hooks were varied after setting the alveolar bone loss to 0, 2, or 4 mm. Under 100 g of intrusive force, initial displacement of the individual teeth in three directions and the degree of labial tilting were measured. Results The degree of labial tilting increased with reduced alveolar bone height under the same load. When a miniscrew was inserted between the two central incisors, the amounts of medial-lateral and anterior-posterior displacement of the central incisor were significantly greater than in the other conditions. When the miniscrews were inserted distally to the canines and an intrusion force was applied distal to the lateral incisors, the degree of labial tilting and the amounts of displacement of the six anterior teeth were the lowest, and the maximum von Mises stress was distributed evenly across all the teeth, regardless of the bone loss. Conclusions Initial tooth displacement similar to pure intrusion of the six maxillary anterior teeth was induced when miniscrews were inserted distal to the maxillary canines and an intrusion force was applied distal to the lateral incisors. In this condition, the maximum von Mises stresses were relatively evenly distributed across all the teeth, regardless of the bone loss. PMID:27668194

Management of Tooth Wear: A Holistic, Dental, Medical, and Mental Healthcare Approach.

PubMed

Ahmed, Khaled E

2016-08-01

Tooth wear is a condition that affects a substantial cohort of dental patients. It has a measurable impact on patients' satisfaction, and overall quality of life. Recently, with growing evidence, our understanding of the aetiology, progression, and management of tooth wear has evolved. The paper argues that pathological tooth wear should not be solely considered as a dental condition, but rather a dental manifestation of other mental and medical disorders. As such, successful management of tooth wear, and its underlying aetiology, requires a holistic, multidisciplinary management approach, involving dental, medical, and mental healthcare providers.

Tooth color: effects on judgments of attractiveness and age.

PubMed

Grosofsky, Alexis; Adkins, Sarah; Bastholm, Robert; Meyer, Leif; Krueger, Lisa; Meyer, Joshua; Torma, Peter

2003-02-01

Tooth whitening has become a very popular procedure. Advertisements for whitening products imply that whiter teeth are more attractive than yellower teeth. We tested this idea empirically by manipulating the tooth color of pictures of male and female targets. Participants' ratings of attractiveness were not influenced by tooth color. Exp. 2 yielded a negative correlation between attractiveness and age ratings: targets judged to be older were rated as less attractive. Unless whiter teeth help in some other way, e.g., improved self-esteem or confidence, it seems that tooth whitening procedures or products are not associated with increased attractiveness to others.

Alloying Elements Transition Into the Weld Metal When Using an Inventor Power Source

NASA Astrophysics Data System (ADS)

Mamadaliev, R. A.; Kuskov, V. N.; Popova, A. A.; Valuev, D. V.

2016-04-01

The temperature distribution over the surface of the welded 12Kh18N10T steel plates using the inventor power source ARC-200 has been calculated. In order to imitate multipass welding when conducting the thermal analysis the initial temperature was changed from 298K up to 798K in 100K increments. It has been determined that alloying elements transition into the weld metal depends on temperature. Using an inventor power source facilitates a uniform distribution of alloying elements along the length and height of the weld seam.

Boundary-layer receptivity of sound with roughness

NASA Technical Reports Server (NTRS)

Saric, William S.; Hoos, Jon A.; Radeztsky, Ronald H.

1991-01-01

An experimental study of receptivity was carried out using an acoustical disturbance in the freestream. The receptivity was enhanced by using a uniform two-dimensional roughness strip (tape). The roughness strip generated the local adjustment in the flow needed to couple the long-wavelength sound wave with the short-wavelength T-S wave. The method proved to be highly sensitive, with slight changes in the forcing frequency or in the height of the 2D roughness element having a strong effect on the amplitude of the observed T-S wave.