Analysis of abamectin residues in avocados by high-performance liquid chromatography with fluorescence detection.

PubMed

Hernández-Borges, Javier; Ravelo-Pérez, Lidia M; Hernández-Suárez, Estrella M; Carnero, Aurelio; Rodríguez-Delgado, Miguel Angel

2007-09-21

In this work an analytical method for the determination of abamectin residues in avocados is developed using high-performance liquid chromatography (HPLC) with fluorescence (FL) detection. A pre-column derivatization with trifluoroacetic anhydride (TFAA) and N-methylimidazole (NMIM) was carried out. The mobile phase consisted of water, methanol and acetonitrile (5:47.5:47.5 v/v/v) and was pumped at a rate of 1 mL/min (isocratic elution). The fluorescence detector was set at an excitation wavelength of 365 nm and an emission wavelength of 470 nm. Homogenized avocado samples were extracted twice with acetonitrile:water 8:2 (v/v) and cleaned using C(18) solid-phase extraction (SPE) cartridges. Recovery values were in the range 87-98% with RSD values lower than 13%. The limits of detection (LODs) and quantification (LOQs) of the whole method were 0.001 and 0.003 mg/kg, respectively. These values are lower than the maximum residue limit (MRL) established by the European Union (EU) and the Spanish legislation in avocado samples.

Combination of QuEChERS and DLLME for GC-MS determination of pesticide residues in orange samples.

PubMed

Andraščíková, Mária; Hrouzková, Svetlana; Cunha, Sara C

2013-01-01

A new method combining QuEChERS (quick, easy, cheap, effective, rugged and safe) and DLLME (dispersive liquid-liquid microextraction) followed by gas chromatography-mass spectrometry with selected ion monitoring (SIM) was developed for the simultaneous determination of 19 pesticides from nine chemical groups exhibiting or suspected to exhibit endocrine-disrupting properties in orange samples. Acetonitrile extract obtained from QuEChERS extraction was used for DLLME as dispersive solvent and carbon tetrachloride as extractive solvent to increase the enrichment factor of the extraction procedure. The effect of several extraction parameters, such as volume extract achieved by the QuEChERS method and subsequently used for DLLME, selection of extractive solvent and its volume, was tested. Under optimum conditions, good linearity, satisfactory recoveries and repeatability were obtained. Limits of quantification (LOQs) achieved (ranging from 0.02 to 47 ng/g) were below the maximum residue limits established by the European Union. The proposed method was applied to the monitoring of pesticide residue levels in oranges commercialised in Portugal.

Ultrasonically Modified Amended-Cloud Point Extraction for Simultaneous Pre-Concentration of Neonicotinoid Insecticide Residues.

PubMed

Kachangoon, Rawikan; Vichapong, Jitlada; Burakham, Rodjana; Santaladchaiyakit, Yanawath; Srijaranai, Supalax

2018-05-12

An effective pre-concentration method, namely amended-cloud point extraction (CPE), has been developed for the extraction and pre-concentration of neonicotinoid insecticide residues. The studied analytes including clothianidin, imidacloprid, acetamiprid, thiamethoxam and thiacloprid were chosen as a model compound. The amended-CPE procedure included two cloud point processes. Triton™ X-114 was used to extract neonicotinoid residues into the surfactant-rich phase and then the analytes were transferred into an alkaline solution with the help of ultrasound energy. The extracts were then analyzed by high-performance liquid chromatography (HPLC) coupled with a monolithic column. Several factors influencing the extraction efficiency were studied such as kind and concentration of surfactant, type and content of salts, kind and concentration of back extraction agent, and incubation temperature and time. Enrichment factors (EFs) were found in the range of 20⁻333 folds. The limits of detection of the studied neonicotinoids were in the range of 0.0003⁻0.002 µg mL −1 which are below the maximum residue limits (MRLs) established by the European Union (EU). Good repeatability was obtained with relative standard deviations lower than 1.92% and 4.54% for retention time ( t R ) and peak area, respectively. The developed extraction method was successfully applied for the analysis of water samples. No detectable residues of neonicotinoids in the studied samples were found.

Investigation of enrofloxacin residues in broiler tissues using ELISA and LC-MS/MS.

PubMed

Panzenhagen, Pedro Henrique N; Aguiar, Waldemir S; Gouvêa, Raquel; de Oliveira, Andréa M G; Barreto, Fabiano; Pereira, Virgínia L A; Aquino, Maria Helena C

2016-01-01

This study investigated the efficiency of an enrofloxacin ELISA test kit to detect the presence of enrofloxacin residues in broiler tissues compared with LC-MS/MS. Broiler tissues from 72 samples consisting of 60 breast muscle, six pools of livers (500 g each) and six pools of kidneys (500 g each) were obtained from six different slaughterhouses. Breast muscle from 10 carcasses and pools of livers and kidneys from approximately 200 carcasses of the same flock were collected from each slaughterhouse. ELISA and HPLC were used to identify and quantify the contamination of the samples with enrofloxacin. A total of 72% of the analysed samples contained enrofloxacin residues detected by the ELISA and 22.2% were detected by LC-MS/MS. The mean values of enrofloxacin contamination found in chicken breast by ELISA and HPLC were 8.63 and 12.25 μg kg(-1), respectively. None of the samples exceeded the maximum limit of 100 μg kg(-1) by both methods set by the European Union as well as the Brazilian Agriculture Ministry. All positive samples for enrofloxacin residues detected by LC-MS/MS were also positive by ELISA. These data confirm the efficiency of the ELISA test, and suggest its use as a screening method for enrofloxacin residues in poultry tissues due to its quick results, low price and ease of applicability.

A simple, fast and cheap non-SPE screening method for antibacterial residue analysis in milk and liver using liquid chromatography-tandem mass spectrometry.

PubMed

Martins, Magda Targa; Melo, Jéssica; Barreto, Fabiano; Hoff, Rodrigo Barcellos; Jank, Louise; Bittencourt, Michele Soares; Arsand, Juliana Bazzan; Schapoval, Elfrides Eva Scherman

2014-11-01

In routine laboratory work, screening methods for multiclass analysis can process a large number of samples in a short time. The main challenge is to develop a methodology to detect as many different classes of residues as possible, combined with speed and low cost. An efficient technique for the analysis of multiclass antibacterial residues (fluoroquinolones, tetracyclines, sulfonamides and trimethoprim) was developed based on simple, environment-friendly extraction for bovine milk, cattle and poultry liver. Acidified ethanol was used as an extracting solvent for milk samples. Liver samples were treated using EDTA-washed sand for cell disruption, methanol:water and acidified acetonitrile as extracting solvent. A total of 24 antibacterial residues were detected and confirmed using liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS), at levels between 10, 25 and 50% of the maximum residue limit (MRL). For liver samples a metabolite (sulfaquinoxaline-OH) was also monitored. A validation procedure was conducted for screening purposes in accordance with European Union requirements (2002/657/EC). The detection capability (CCβ) false compliant rate was less than 5% at the lowest level for each residue. Specificity and ruggedness were also discussed. Incurred and routine samples were analyzed and the method was successfully applied. The results proved that this method can be an important tool in routine analysis, since it is very fast and reliable. Copyright © 2014. Published by Elsevier B.V.

Role of Sample Processing Strategies at the European Union National Reference Laboratories (NRLs) Concerning the Analysis of Pesticide Residues.

PubMed

Hajeb, Parvaneh; Herrmann, Susan S; Poulsen, Mette E

2017-07-19

The guidance document SANTE 11945/2015 recommends that cereal samples be milled to a particle size preferably smaller than 1.0 mm and that extensive heating of the samples should be avoided. The aim of the present study was therefore to investigate the differences in milling procedures, obtained particle size distributions, and the resulting pesticide residue recovery when cereal samples were milled at the European Union National Reference Laboratories (NRLs) with their routine milling procedures. A total of 23 NRLs participated in the study. The oat and rye samples milled by each NRL were sent to the European Union Reference Laboratory on Cereals and Feedingstuff (EURL) for the determination of the particle size distribution and pesticide residue recovery. The results showed that the NRLs used several different brands and types of mills. Large variations in the particle size distributions and pesticide extraction efficiencies were observed even between samples milled by the same type of mill.

Foliar Desiccators Glyphosate, Carfentrazone, and Paraquat Affect the Technological and Chemical Properties of Cowpea Grains.

PubMed

Lindemann, Igor da Silva; Lang, Gustavo Heinrich; Hoffmann, Jessica Fernanda; Rombaldi, Cesar Valmor; de Oliveira, Maurício; Elias, Moacir Cardoso; Vanier, Nathan Levien

2017-08-16

The effects of the use of glyphosate (GLY), glyphosate plus carfentrazone (GLY/CAR), and paraquat (PAR) as plant desiccators on the technological and chemical properties of cowpea grains were investigated. All studied desiccants provided lower cooking time to freshly harvested cowpea. However, the coat color of PAR- and GLY/CAR-treated cowpea was reddish in comparison to the control treatment. Principal component analysis (PCA) from liquid chromatography-mass spectrometry (LC-MS) data sets showed a clear distinction among cowpea from the different treatments. Catechin-3-glucoside and epicatechin significantly contributed for discriminating GLY-treated cowpea, while citric acid was responsible for discriminating GLY/CAR-treated cowpea. Quercetin derivative and gluconic acid were responsible for discriminating control treatment. Residual glyphosate and paraquat content was higher than the maximum limits allowed by Codex Alimentarius and the European Union Commission. Improvements in the technological and chemical properties of cowpea may not be overlapped by the risks that those desiccants exhibit when exceeding the maximum limits of tolerance in food.

Dissipation kinetics of emamectin benzoate and lufenuron residues in cabbage grown under field conditions.

PubMed

Dong, Bizhang; Zhao, Qing; Hu, Jiye

2015-12-01

Residue analysis of emamectin benzoate and lufenuron in cabbage matrices and soil was developed using a quick, easy, cheap, effective, rugged, and safe (QuEChERS) method and ultra high-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS). The samples were extracted with 1% acetic acid in acetonitrile (v/v) or 1% acetic acid in acetonitrile/water (5:1, v/v) and cleaned up by dispersive solid-phase extraction. Mean recoveries and relative standard deviations (RSDs) in all samples ranged 87.8-100.0 % and 3.6-12.6% for emamectin benzoate and 87.8-104.8 % and 6.2-11.5% for lufenuron, respectively. The validated method was used to evaluate the dissipation rate of emamectin benzoate and lufenuron in cabbage and soil as well as the residual levels in harvested cabbage and soil at different preharvest intervals (PHI). The half-lives of emamectin benzoate and lufenuron were 1.08-2.70 and 1.74-5.04 days in cabbage, and 1.42-4.01 and 0.94-6.18 days in soil, respectively. The terminal residues were below the China maximum residue limits (MRLs) at 3 days for emamectin benzoate (0.1 mg kg(-1)) and European Union MRLs at 5 days for lufenuron (0.5 mg kg(-1)), which suggested that 5 days could be recommended as the PHI for the commercial formulation of emamectin benzoate and lufenuron application in the Chinese cabbage field.

Monitoring of streptomycin and dihydrostreptomycin residual levels in porcine meat press juice and muscle via solid-phase fluorescence immunoassay and confirmatory analysis by liquid chromatography after post-column derivatization.

PubMed

Pyun, Chang-Won; Abd El-Aty, A M; Hashim, M M M; Shim, Jae-Han; Lee, Si-Kyung; Choi, Kang-Duk; Park, Kwan-Ha; Shin, Ho-Chul; Lee, Chiho

2008-03-01

A solid-phase fluorescence immunoassay (SPFIA) that was primarily developed for detection of antibiotic residues in milk was qualitatively applied for the pre-screening of the residues of aminoglycoside antibiotics, streptomycin and dihydrostreptomycin, in meat press juice. The confirmation of both analytes was performed using a validated method of highperformance liquid chromatography with post-column derivatization. The analytical performance was demonstrated by the analysis of pork meat samples spiked at three concentration levels, ranging from 0.25 to 2.5 ppm for each analyte. In general, the recoveries ranged from 80.4 to 81.5% and from 79.6 to 84.4% for streptomycin and dihydrostreptomycin, respectively, with relative standard deviations lower than 6%. The limits of detection were 0.1 and 0.15 ppm for streptomycin and dihydrostreptomycin, respectively, and the limits of quantification of 0.35 and 0.5 ppm are below the maximum residue limits of Codex, the European Union, and the Korean Food and Drug Administration (ranging from 0.5 to 0.6 ppm). Eight real samples collected from the Seoul area were first monitored using SPFIA, and none of them were found positive. These findings are in good accordance with those observed by HPLC analysis. To the best of our knowledge, this is the first report to monitor the aminoglycoside residues in pork meat press juice using SPFIA.

Pesticide residue levels in green beans cultivated in Souss Masa valley (Morocco) after multiple applications of bifenthrin and λ-cyhalothrin.

PubMed

Bouri, M; Salghi, R; Bazzi, Lh; Zarrouk, A; Rios, A; Zougagh, M

2012-09-01

Dissipation of bifenthrin and λ-cyhalothrin pyrethroid insecticides, under environmental conditions, was evaluated on green beans grown in experimental greenhouses (Souss Massa valley, Morocco). Pesticide residues were determined by gas chromatography with micro electron-capture detector (GC-μECD) after dichloromethane extraction and cleanup on florisil phase cartridges. In the case of field experiments, a random block scheme was employed. Each block contained 25 plants in a single row and tests were carried out in triplicates applying pesticides at the recommended doses by the manufacturers. Fruit samples were periodically taken until the end of the preharvest interval (p.i.). The results obtained showed that the p.i of bifenthrin in green bean were 4 days in the winter and 3.5 days in the spring, whereas that for λ-cyhalothrin 8 days was found in the winter and 7.5 days in the spring. Consequently, it is possible to consider the European Union maximum residue limit (EU MRL) values compatible with the proper agricultural practices used for growing green bean in the plastic greenhouse of Souss Massa valley in South Morocco. Bifenthrin had a degradation of first-order kinetics, whereas that of levels for λ-cyhalothrin residue can not be interpreted by the use of a first order model.

Presence of pesticide residues on produce cultivated in Suriname.

PubMed

Abdoel Wahid, F; Wickliffe, J; Wilson, M; Van Sauers, A; Bond, N; Hawkins, W; Mans, D; Lichtveld, M

2017-06-01

Agricultural pesticides are widely used in Suriname, an upper middle-income Caribbean country located in South America. Suriname imported 1.8 million kg of agricultural pesticides in 2015. So far, however, national monitoring of pesticides in crops is absent. Reports from the Netherlands on imported Surinamese produce from 2010 to 2015 consistently showed that samples exceeded plant-specific pesticide maximum residue limits (MRLs) of the European Union (EU). Consumption of produce containing unsafe levels of pesticide residues can cause neurological disorders, and particularly, pregnant women and children may be vulnerable. This pilot study assessed the presence of pesticide residues in commonly consumed produce items cultivated in Suriname. Thirty-two insecticides (organophosphates, organochlorines, carbamates, and pyrethroids) and 12 fungicides were evaluated for their levels in nine types of produce. Pesticide residue levels exceeding MRLs in this study regarded cypermethrin (0.32 μg/g) in tomatoes (USA MRL 0.20 μg/g), lambda-cyhalothrin (1.08 μg/g) in Chinese cabbage (USA MRL 0.40 μg/g), endosulfan (0.07 μg/g) in tannia (EU MRL 0.05 μg/g), and lindane (0.02 and 0.03 μg/g, respectively) in tannia (EU MRL 0.01 μg/g). While only a few pesticide residues were detected in this small pilot study, these residues included two widely banned pesticides (endosulfan and lindane). There is a need to address environmental policy gaps. A more comprehensive sampling and analysis of produce from Suriname is warranted to better understand the scope of the problem. Preliminary assessments, using intake rate, hazard quotient, and level of concern showed that it is unlikely that daily consumption of tannia leads to adverse health effects.

Presence of pesticide residues on produce cultivated in Suriname

PubMed Central

Wickliffe, J.; Wilson, M.; Van Sauers, A.; Bond, N.; Hawkins, W.; Mans, D.; Lichtveld, M.

2017-01-01

Agricultural pesticides are widely used in Suriname, an upper middle-income Caribbean country located in South America. Suriname imported 1.8 million kg of agricultural pesticides in 2015. So far, however, national monitoring of pesticides in crops is absent. Reports from the Netherlands on imported Surinamese produce from 2010 to 2015 consistently showed that samples exceeded plant-specific pesticide maximum residue limits (MRLs) of the European Union (EU). Consumption of produce containing unsafe levels of pesticide residues can cause neurological disorders, and particularly, pregnant women and children may be vulnerable. This pilot study assessed the presence of pesticide residues in commonly consumed produce items cultivated in Suriname. Thirty-two insecticides (organophosphates, organochlorines, carbamates, and pyrethroids) and 12 fungicides were evaluated for their levels in nine types of produce. Pesticide residue levels exceeding MRLs in this study regarded cypermethrin (0.32 μg/g) in tomatoes (USA MRL 0.20 μg/g), lambda-cyhalothrin (1.08 μg/g) in Chinese cabbage (USA MRL 0.40 μg/g), endosulfan (0.07 μg/g) in tannia (EU MRL 0.05 μg/g), and lindane (0.02 and 0.03 μg/g, respectively) in tannia (EU MRL 0.01 μg/g). While only a few pesticide residues were detected in this small pilot study, these residues included two widely banned pesticides (endosulfan and lindane). There is a need to address environmental policy gaps. A more comprehensive sampling and analysis of produce from Suriname is warranted to better understand the scope of the problem. Preliminary assessments, using intake rate, hazard quotient, and level of concern showed that it is unlikely that daily consumption of tannia leads to adverse health effects. PMID:28567597

The Landrum-Griffin Act. Twenty Years of Federal Protection of Union Members' Rights. Labor Relations and Public Policy Series, No. 19.

ERIC Educational Resources Information Center

Bellace, Janice R.; Berkowitz, Alan D.

Enacted in 1959, the Landrum-Griffin Act or Labor-Management Reporting and Disclosure Act was intended to attain maximum protection for the rights of individual workers within the union without undermining the union as an institution necessary for the existence of collective bargaining. Title I is the union members' bill of rights; titles II-VI…

Multiresidue method for pesticide residue analysis in food of animal and plant origin based on GC or LC and MS or MS/MS.

PubMed

Muñoz, Eva; Muñoz, Gloria; Pineda, Laura; Serrahima, Eulalia; Centrich, Francesc

2012-01-01

A multiresidue method based on GC or LC and MS or MS/MS for the determination of 204 pesticides in diverse food matrixes of animal and plant origin is described. The method can include different stages of cleanup according to the chemical characteristics of each sample. Samples were extracted using accelerated solvent extraction. Those with a high fat content or that contained chlorophyll required further purification by gel permeation chromatography and/or SPE (ENVI-Carb). The methodology developed here was fully validated; the LOQs for the 204 pesticides are presented. The LOQ values lie between 0.01 to 0.02 mg/kg. However, in some cases, mainly in baby food, they were as low as 0.003 mg/kg, thereby meeting European Union requirements on maximum residue levels for pesticides, as outlined in European regulation 396/2005 and the Commission Directive 2003/13/EC. The procedure has been accredited for a wide scope of pesticides and matrixes by the Spanish Accreditation Body (ENAC) following ISO/IEC 17025:2005, as outlined in ENAC technical note NT-19.

Limited survey for the presence of aflatoxins in foods from local markets and supermarkets in Valencia, Spain.

PubMed

Blesa, J; Soriano, J M; Moltó, J C; Mañes, J

2004-02-01

Aflatoxin B1 (AFB1), B2 (AFB2), G1 (AFG1) and G2 (AFG2) were extracted by matrix solid-phase dispersion with C18 silica and acetonitrile as the eluting solvent, analysed by liquid chromatography with fluorescence detection and confirmed by liquid chromatography with mass spectrometry using an electrospray interface in 58 samples grouped as cereals, dried fruits, herbs and spices, pulses, snacks, and nuts and nut products collected from local markets and supermarkets in Valencia, Spain. All samples analysed by the proposed method were previously studied with an enzyme-linked immunosorbent assay as a screening protocol for the fast detection of mycotoxins. The samples containing residues (3/58) were hazelnut (0.42 and 0.52 microg kg(-1) for AFB1 and AFG1, respectively), nut cocktail (0.29 and 0.47 microg kg(-1) for AFB1 and AFG1, respectively) and pinhol (0.30 microg kg(-1) for AFG1). Such values were below the legislated maximum residue levels for the European Union.

The detection limits of antimicrobial agents in cow's milk by a simple Yoghurt Culture Test.

PubMed

Mohsenzadeh, M; Bahrainipour, A

2008-09-15

The aim of this study was to study performance of Yoghurt Culture Test (YCT) in the detection of antimicrobial residues in milk. For this purpose, the sensitivity of YCT for 15 antibiotics were determined. For each drug, 8 concentrations were tested. The detection limits of YCT at 2.5 h and 4 h incubation were determined (microg kg(-1)): 15 and 37.5, penicillin G; 4 and 5, ampicillin; 5 and 7.5, amoxycillin; 100 and 200, cephalexin; 80 and 100, cefazoline; 100 and 200, oxytetracycline; 500 and 100, chlortetracycline; 100 and 200, tetracycline; 150 and 200, doxycycline; 200 and 400, sulphadimidine; 500 and 1000, gentamycin; 1000 and 1500, spectinomycin; 400 and 500, erythromycin; 50 and 100, tylosin; 5000 and 10000, chloramphenicol. The YCT detection limits at 2.5 h incubation for ampicillin, cephalexin, tetracycline, oxytetracycline and tylosin are similar to those obtained as Maximum Residue Limit (MRL) according to Regulation 2377/90 EEC as set out by the European Union. In addition the detection limits of YCT for some antibiotics were lower than some of microbial inhibitor test.

[Plant protection products and their residues : Aspects of consumer safety in context of the new EU regulations].

PubMed

Banasiak, U; Michalski, B; Pfeil, R; Solecki, R

2010-06-01

The law regulating plant protection products (PPP) in the European Union (EU) was fundamentally revised through the introduction of Regulation (EC) No. 1107/2009 which is due to enter into force on 14 June 2011. EU-wide harmonized maximum residue levels (MRLs) for the active substances of PPP in foods are laid down in Regulation (EC) No. 396/2005 and apply since entry into force of the regulation on 1 September 2008. The goal of both regulations is to strengthen the level of consumer protection. PPP are subject to a strict assessment of active substances, which is regulated at the EU level as well as an authorization procedure in the EU Member States. Prior to application for authorization of a PPP, the active substance(s) it contains must be included in a positive list. Tests regarding the toxicity and residue behavior of PPP must be conducted by the applicant, and the respective documents must be submitted to the authorities for evaluation. Following review of the required data, toxicological threshold values are derived, consumer exposure is assessed, and the risk to health is evaluated. The goal of this evaluation is to ensure that the use of PPP according to good plant protection practice does not have any harmful effects on human health.

Maximum number of children per sperm donor based on false paternity rate.

PubMed

Sánchez-Castelló, Isabel M; Gonzalvo, María C; Clavero, Ana; López-Regalado, María L; Mozas, Juan; Martínez-Granados, Luis; Navas, Purificación; Castilla, José A

2017-03-01

The aim of this study is to estimate the weight of each relevant factor in such unions of inadvertent consanguinity and to determine a "reasonable" limit for the number of children per donor, matching the probability of inadvertent consanguinity arising from the use of sperm donor in assisted reproduction with that of such a union arising from false paternity. In this study, we applied to Spanish data a mathematical model of consanguineous unions, taking into account the following factors: maximum number of live births/donor, fertility rate, average number of births per donor in a pregnancy, donor success rate, matings per phenotype, number of newborns/year, and number of donors needed in the population/year and births by false paternity. In Spain, the number of inadvertent unions between descendants of the same donor in Spain has been estimated at 0.4/year (one every two and a half years), although this frequency decreases as the reference population increases. On the other hand, the frequency of unions between family members due to false paternity has been estimated at 6.1/year. Thus, only 6% of such unions are due to the use of donor sperm. A total of 25 children per sperm donor are needed to align the probability of inadvertant consanguinity arising from the use of assisted reproduction with that due to false paternity. Therefore, we consider this number to be the maximum "reasonable" number of children born per donor in Spain.

Residue evaluation of imidacloprid, spirotetramat, and spirotetramat-enol in/on grapes (Vitis vinifera L.) and soil.

PubMed

Mohapatra, Soudamini; Kumar, Sampath; Prakash, G S

2015-10-01

A combination of imidacloprid and spirotetramat effectively controls sucking pests on grapevines. Residues of these insecticides on grapes were evaluated after treatment with spirotetramat 12% + imidacloprid 12% (240 SC) three times at 90 and 180 g a.i. ha(-1). The samples were extracted and purified by QuEChERS method and analyzed by high-performance liquid chromatography with a photodiode array detector (imidacloprid) and gas chromatography mass spectrometry (spirotetramat and its metabolite spirotetramat-enol). Satisfactory results were obtained with ranges of 80.6-98.6% for the recovery, 3.1-10% for the relative standard deviation range, and 9.8-15.6% for the uncertainty. The limits of detection and quantification were 0.015 μg mL(-1) and 0.05 mg kg(-1), respectively. Initial residue concentrations of imidacloprid after the 90 and 180 g a.i. ha(-1) treatments were 0.912 (half-life 11 days) and 1.681 mg kg(-1) (half-life 12.4 days), respectively. For spirotetramat + spirotetramat-enol, the residue concentrations were 1.337 (half-life 5.6 days) and 2.0 mg kg(-1) (half-life 7.6 days) for the 90 and 180 g a.i. ha(-1) treatments, respectively. Spirotetramat degraded faster than spirotetramat-enol. After treatment at 90 g a.i. ha(-1), the initial residues of both insecticides were within European Union maximum residue limits and a 1-day pre-harvest interval (PHI) was adequate for safe consumption of grapes. After treatment at 180 g a.i. ha(-1), the required PHI was 7 day. Therefore, a PHI of 7 day should be used after treatment with imidacloprid and spirotetramat.

Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718.

PubMed

Hua, Yang; Liu, Zhanqiang

2018-05-24

Residual stresses of turned Inconel 718 surface along its axial and circumferential directions affect the fatigue performance of machined components. However, it has not been clear that the axial and circumferential directions are the principle residual stress direction. The direction of the maximum principal residual stress is crucial for the machined component service life. The present work aims to focuses on determining the direction and magnitude of principal residual stress and investigating its influence on fatigue performance of turned Inconel 718. The turning experimental results show that the principal residual stress magnitude is much higher than surface residual stress. In addition, both the principal residual stress and surface residual stress increase significantly as the feed rate increases. The fatigue test results show that the direction of the maximum principal residual stress increased by 7.4%, while the fatigue life decreased by 39.4%. The maximum principal residual stress magnitude diminished by 17.9%, whereas the fatigue life increased by 83.6%. The maximum principal residual stress has a preponderant influence on fatigue performance as compared to the surface residual stress. The maximum principal residual stress can be considered as a prime indicator for evaluation of the residual stress influence on fatigue performance of turned Inconel 718.

Development and validation of an ultra performance liquid chromatography Q-Exactive Orbitrap mass spectrometry for the determination of fipronil and its metabolites in tea and chrysanthemum.

PubMed

Chen, Hongping; Gao, Guanwei; Liu, Pingxiang; Pan, Meiling; Chai, Yunfeng; Liu, Xin; Lu, Chengyin

2018-04-25

A fast, sensitive and reliable method for the determination of fipronil and its metabolites in tea and chrysanthemum was developed using a modified QuEChERS technique and an ultra performance liquid chromatography Q-Exactive Orbitrap mass spectrometry. The mixture of adsorbents containing primary secondary amine (PSA), octadecylsilane (C 18 ) and carbon nanotubes (CNTs), was used as QuEChERS adsorbents. The use of mass resolution at 70000 full width at half maximum (FWHM) and narrow mass windows at 5 ppm achieved high selectivity and repeatability. Satisfactory linearity with correlative coefficient (R 2 ) higher than 0.996 was achieved for all compounds. Recoveries at three levels (2, 10 and 50 μg kg -1 ) ranged from 86% to 112%, while the intra- and inter-day accuracies were less than 15%. Limits of quantification for fipronil and its metabolites were 2 μg kg -1 , which fulfils the requirement of maximum residue limits formulated by European Union and Japan. Copyright © 2017 Elsevier Ltd. All rights reserved.

Screening of fluoroquinolone residues in caprine milk using a 5-kg luminescence photometer

USDA-ARS?s Scientific Manuscript database

A terbium-sensitized luminescence (TSL) method was developed to screen presence of residues of four fluoroquinolones (FQ) registered in caprine milk in the European Union: enrofloxacin, ciprofloxacin, flumequine, and danofloxacin. After extraction in McIlvaine buffer and SPE cleanup, TSL was measure...

78 FR 33445 - Office of Small Credit Unions (OSCUI) Grant Program Access For Credit Unions

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-04

... hardware and software necessary to convert to computerized operations. The maximum award amount for this...,000 per credit union for financial education projects that improve financial capability in the... found on D&B's Web site at http://fedgov.dnb.com/webform or by calling D&B, toll-free, at 1-866-705-5711...

Evaluation of regulatory variation and theoretical health risk for pesticide maximum residue limits in food.

PubMed

Li, Zijian

2018-08-01

To evaluate whether pesticide maximum residue limits (MRLs) can protect public health, a deterministic dietary risk assessment of maximum pesticide legal exposure was conducted to convert global MRLs to theoretical maximum dose intake (TMDI) values by estimating the average food intake rate and human body weight for each country. A total of 114 nations (58% of the total nations in the world) and two international organizations, including the European Union (EU) and Codex (WHO) have regulated at least one of the most currently used pesticides in at least one of the most consumed agricultural commodities. In this study, 14 of the most commonly used pesticides and 12 of the most commonly consumed agricultural commodities were identified and selected for analysis. A health risk analysis indicated that nearly 30% of the computed pesticide TMDI values were greater than the acceptable daily intake (ADI) values; however, many nations lack common pesticide MRLs in many commonly consumed foods and other human exposure pathways, such as soil, water, and air were not considered. Normality tests of the TMDI values set indicated that all distributions had a right skewness due to large TMDI clusters at the low end of the distribution, which were caused by some strict pesticide MRLs regulated by the EU (normally a default MRL of 0.01 mg/kg when essential data are missing). The Box-Cox transformation and optimal lambda (λ) were applied to these TMDI distributions, and normality tests of the transformed data set indicated that the power transformed TMDI values of at least eight pesticides presented a normal distribution. It was concluded that unifying strict pesticide MRLs by nations worldwide could significantly skew the distribution of TMDI values to the right, lower the legal exposure to pesticide, and effectively control human health risks. Copyright © 2018 Elsevier Ltd. All rights reserved.

Impacts of alum residues from Morton Jaffray Water Works on water quality and fish, Harare, Zimbabwe

NASA Astrophysics Data System (ADS)

Muisa, Norah; Hoko, Zvikomborero; Chifamba, Portia

Metal pollution of freshwater due to human activities is a major problem confronting most urban centres in developing countries. This study determined the extent to which aluminium in the residues from Morton Jaffray Water Works in Harare were affecting the water quality of Manyame River and Lake Manyame. The study also measured aluminium bioaccumulation in Nile Tilapia ( Oreochromis niloticus) which is of importance to the commercial fisheries industry in Zimbabwe. Depth integrated water, and sediment grab samples and adult fish were collected per site in January and March, 2010. A total of six sites were selected on the Manyame River and in Lake Manyame. The levels of Total Aluminium (Al) were determined in sediments, water and fish tissues (liver, kidney, gill and muscle). Total solids, total dissolved solids, conductivity, pH, dissolved oxygen and temperature were also determined in water and residues. The texture of the sediments was also assessed. Aluminium concentration in water ranged from 2.19 mg/L to 68.93 mg/L during both sampling campaigns surpassing permissible maximum concentration limits of 0.087 to 0.75 mg/L suggested by the Environmental Protection Agency and African Union. The site upstream of the discharge point of the residues always had the lowest levels though it was higher than acceptable levels indicated above, thus suggesting the existence of other sources of aluminium in the catchment besides Morton Jaffray Water Works. However, there was a 10-fold and 100-fold increase in levels of aluminium in water and sediments, respectively, at the site 100 m downstream of the discharge point on the Manyame River. Mean aluminium concentrations in water and sediments at this site averaged 68.93 ± 61.74 mg/L and 38.18 ± 21.54 mg/L in water and 103.79 ± 55.96 mg/L and 131.84 ± 16.48 mg/L in sediments in sampling campaigns 1 and 2, respectively. These levels were significantly higher than levels obtained from all the other sites during both sampling campaigns (ANOVA: p < 0.05). This also indicated that the contribution of aluminium pollution from the water works residues was higher than all the other sources in the catchment. Aluminium levels were generally in the order of; sediments > fish > water. Bioaccumulation occurred in the fish and the order of bioconcentration was; kidney > liver > gill > muscle. The amounts of aluminium in the fish tissues investigated were significantly higher (maximum = 2.92 mg/g) than was reported in other studies reviewed (maximum = 0.18 mg/g). Thus, the water treatment plant residues are greatly increasing the concentrations of aluminium in the water system downstream of the plant thus creating a great risk of aluminium toxicity for fish. Treatment of the residues before discharge, substitution of alum with other coagulants, and re-use of the residues in buffer strips, agricultural lands and in sewage works should be considered.

Organophosphorus pesticide residues in vegetables from farms, markets, and a supermarket around Kwan Phayao Lake of Northern Thailand.

PubMed

Sapbamrer, Ratana; Hongsibsong, Surat

2014-07-01

This study investigated organophosphorus (OP) residues in vegetables from 27 farms, 106 markets, and 1 supermarket around Kwan Phayao Lake, Northern Thailand, between August and September 2013. Types of vegetables sampled were all vegetables cultivated or sold around the study site. The most common OP pesticides detected in farm samples were chlorpyrifos (50 %), malathion (31.8 %), monocrotophos (31.8 %), diazinon (13.6 %), omethoate (13.6 %), and dicrotophos (9.1 %). The most common OP pesticides detected in market samples were chlorpyrifos (33.9 %), diazinon (18.6 %), parathion-methyl (3.4 %), profenofos (3.4 %), primiphos-ethyl (3.4 %), and fenitrothion (1.7 %). The OP pesticides detected in supermarket samples were chlorpyrifos (33.3 %), and diazinon (66.7 %). Among the compounds detected, chlorpyrifos was detected in most of the vegetable samples from all sources. The highest chlorpyrifos level in farm samples were found in lemon balm (2.423 mg/kg) followed by Vietnamese coriander (0.835 mg/kg), and cowpea (0.027 mg/kg). The highest level in markets samples were found in garlic (7.785 mg/kg) followed by Chinese cabbage (2.864 mg/kg) and Vietnamese coriander (1.308 mg/kg). Residues from supermarket samples were found only in parsley (0.027 mg/kg). The findings showed that 16 samples (59.3 %) from farms and 14 samples (13.2 %) from markets contained OP residues at or above the maximum residue limits established by the European Union. It is concluded that awareness, safety education, and strict regulation of pesticide use are necessary.

Impact of a proposed revision of the IESTI equation on the acute risk assessment conducted when setting maximum residue levels (MRLs) in the European Union (EU): A case study.

PubMed

Breysse, Nicolas; Vial, Gaelle; Pattingre, Lauriane; Ossendorp, Bernadette C; Mahieu, Karin; Reich, Hermine; Rietveld, Anton; Sieke, Christian; van der Velde-Koerts, Trijntje; Sarda, Xavier

2018-06-03

Proposals to update the methodology for the international estimated short-term intake (IESTI) equations were made during an international workshop held in Geneva in 2015. Changes to several parameters of the current four IESTI equations (cases 1, 2a, 2b, and 3) were proposed. In this study, the overall impact of these proposed changes on estimates of short-term exposure was studied using the large portion data available in the European Food Safety Authority PRIMo model and the residue data submitted in the framework of the European Maximum Residue Levels (MRL) review under Article 12 of Regulation (EC) No 396/2005. Evaluation of consumer exposure using the current and proposed equations resulted in substantial differences in the exposure estimates; however, there were no significant changes regarding the number of accepted MRLs. For the different IESTI cases, the median ratio of the new versus the current equation is 1.1 for case 1, 1.4 for case 2a, 0.75 for case 2b, and 1 for case 3. The impact, expressed as a shift in the IESTI distribution profile, indicated that the 95th percentile IESTI shifted from 50% of the acute reference dose (ARfD) with the current equations to 65% of the ARfD with the proposed equations. This IESTI increase resulted in the loss of 1.2% of the MRLs (37 out of 3110) tested within this study. At the same time, the proposed equations would have allowed 0.4% of the MRLs (14 out of 3110) that were rejected with the current equations to be accepted. The commodity groups that were most impacted by these modifications are solanacea (e.g., potato, eggplant), lettuces, pulses (dry), leafy brassica (e.g., kale, Chinese cabbage), and pome fruits. The active substances that were most affected were fluazifop-p-butyl, deltamethrin, and lambda-cyhalothrin.

Determination of six pyrethroid insecticides in fruit juice samples using dispersive liquid-liquid microextraction combined with high performance liquid chromatography.

PubMed

Boonchiangma, Suthasinee; Ngeontae, Wittaya; Srijaranai, Supalax

2012-01-15

Dispersive liquid-liquid microextraction (DLLME) coupled to high performance liquid chromatography (HPLC) with UV detection was applied for the determination of six pyrethroids (tetramethrin, fenpropathrin, cypermethrin, deltamethrin, fenvalerate and permethrin) in various fruit juices including apple, red grape, orange, kiwi, passion fruit, pomegranate and guava juice. Six pyrethroids were separated within 30 min using a Waters Atlantis T3 column under an isocratic elution of acetonitrile-water (72:28). The parameters affecting extraction efficiency of the DLLME method such as type of disperser and extraction solvent, volume of disperser and extraction solvent and centrifugation time were investigated. Under the optimum conditions, 5.00 mL of sample solution, 300 μL of chloroform as extraction solvent and 1.25 mL of methanol as dispersive solvent gave high enrichment factor in the range of 62-84. Good linearity was obtained from 2 to 1,500 μg/L (r(2)>0.995). The mean recoveries of the pyrethroids evaluated by fortification of real samples were in the range of 84-94%. The limits of detection ranging from 2 to 5 μg/L are sufficient to analyze pyrethroid residues at the maximum residue limits (MRLs) established by the European Union (EU) in fruit juices. The proposed method can be applied to direct determination of pyrethroid residues in fruit juices. Copyright © 2011 Elsevier B.V. All rights reserved.

Lethal and sublethal effects of pesticides on Chrysoperla carnea larvae (Neuroptera: Chrysopidae) and the influence of rainfastness in their degradation pattern over time.

PubMed

Maia, Jader Braga; Carvalho, Geraldo Andrade; Medina, Pilar; Garzón, Agustín; Gontijo, Pablo da Costa; Viñuela, Elisa

2016-07-01

The predator Chrysoperla carnea is a model species for the study of non-target effects of pesticides under different scenarios: registration of plant protection products under the European Union and effects of the Bt toxin. Laboratory and persistence studies were carried out with six pesticides currently used in corn crops in Spain that were applied at their maximum field recommended concentrations. The assessed end-points were larval mortality, survivorship until adult stage, duration of the larval and pupal periods, fecundity, fertility and sex ratio of the emerged adults. Based on the total effect (lethal and sublethal) caused to L3 larvae in contact with fresh residues in the laboratory, pendimethalin was harmless (IOBC 1), lambda-cyhalothrin, abamectin, and hexythiazox were slightly harmful (IOBC 2), deltamethrin was moderately harmful (IOBC 3) and chlorpyrifos was harmful (IOBC 4). Afterwards, the residues of the two most toxic pesticides in the lab (deltamethrin and chlorpyrifos) were aged under greenhouse conditions (22 ± 2 °C, 40 ± 10 % R.H., 16.9 μmol m(-2) s(-1) UV radiation) in the presence and absence of artificial rainfall (10 l m(-2) h(-1), applied 24 h after pesticide application). Deltamethrin was classified as short lived (IOBC A) in both cases. However, degradation of chlorpyrifos residues was accelerated in the presence of rainfall, leading to the classification as slightly persistent (IOBC B), while in absence of rainfall it behaved as persistent (IOBC D). Every pesticide can be recommended for inclusion in corn IPM programs where the predator is present except chlorpyrifos that exhibited high direct toxicity in the lab and prolonged residual action even in the presence of rainfall.

Vegephy: impact of vegetable oils used as extemporaneous additives on pesticide residues and their crop protection potential.

PubMed

Rousseau, G; Coutanceau, P; Lebeau, F; Pigeon, O; Ducat, N; De Vos, P

2013-01-01

Within the framework of the VEGEPHY project set up to assess the effect of refined oils used as extemporaneous additives, both alone and in combination with oligosaccharides (guar, xanthan and carboxymethyl cellulose), on the quality of plant protection treatments for wheat, a study was conducted on the effect of combinations of additives on the level of pesticide residues in wheat plants and grain and their impact on treatment efficiency. The use of some of these additives gave efficiency results that were comparable with those obtained with additives that are currently used but are not bio-based. The use of refined oils as extemporaneous additives, both alone and combined with oligosaccharides, led to better penetration by the pesticide as well as longer persistence of its activity. The experiments were conducted with fungicides, herbicides, plant growth regulators and various types of formulation (EC, SC and WG). The results obtained were conclusive, but they did depend on the physico-chemical properties of the active substance. The risk of exceeding the maximum residue levels (MRLs) of pesticides was also evaluated. Even where the MRLs had not been not exceeded, the experiments showed that in some cases the treatment with these additives could lead to pesticide residues up to two times higher than those measured for the treatment without additives. It would be necessary, therefore, to reduce the treatment dose associated with the additive and/or have a long enough pre-harvest interval to avoid exceeding the MRLs. The use of green additives could be a useful and easy way to attain the European Union (EU) goal of reducing pesticide use by improving the retention of active substances on the plant and reducing the number of treatments.

Fluorescence polarization immunoassay using IgY antibodies for detection of valnemulin in swine tissue.

PubMed

Zhang, Huiyan; Mi, Tiejun; Khan, Oleg Yu; Sheng, Yajie; Eremin, Sergei A; Beier, Ross C; Zhang, Suxia; Shen, Jianzhong; Wang, Zhanhui

2015-10-01

Immunoglobulin Y (IgY) is derived from egg yolk and has been identified as a cheap and high-yield immunoreagent. The application of IgY in immunoassays for the detection of chemical contaminants in food samples has rarely been reported. In this work, we describe a rapid and sensitive fluorescence polarization immunoassay (FPIA) for valnemulin (VAL) using IgY which was produced using a previously prepared immunogen. Three fluorophore-labeled VAL tracers were synthesized and the sensitivity of the best tracer (VAL-DTAF) in the optimized FPIA with antibody IgY100 demonstrated an IC50 value of 12 ng mL(-1) in buffer. After evaluation of several extraction procedures, acidified acetonitrile was selected to extract VAL from swine tissue. The recoveries of VAL in spiked swine tissue at three levels (50, 100, and 200 μg kg(-1)) were higher than 79% with coefficients of variation (CVs) lower than 12%. The limit of detection (LOD) of the FPIA in swine tissue was 26 μg kg(-1) and was lower than the maximum residue limit (MRL) of VAL set by the European Union. The study showed that IgY could be a good substitute for IgG when developing a high-throughput assay for chemical residues.

40 CFR 141.54 - Maximum residual disinfectant level goals for disinfectants.

Code of Federal Regulations, 2014 CFR

2014-07-01

... for disinfectants. MRDLGs for disinfectants are as follows: Disinfectant residual MRDLG(mg/L) Chlorine... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Maximum residual disinfectant level goals for disinfectants. 141.54 Section 141.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

40 CFR 141.54 - Maximum residual disinfectant level goals for disinfectants.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for disinfectants. MRDLGs for disinfectants are as follows: Disinfectant residual MRDLG(mg/L) Chlorine... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Maximum residual disinfectant level goals for disinfectants. 141.54 Section 141.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

40 CFR 141.54 - Maximum residual disinfectant level goals for disinfectants.

Code of Federal Regulations, 2013 CFR

2013-07-01

... for disinfectants. MRDLGs for disinfectants are as follows: Disinfectant residual MRDLG(mg/L) Chlorine... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Maximum residual disinfectant level goals for disinfectants. 141.54 Section 141.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

Depletion study, withdrawal period calculation and bioaccumulation of sulfamethazine in tilapia (Oreochromis niloticus) treated with medicated feed.

PubMed

Nunes, Kátia S D; Vallim, José H; Assalin, Márcia R; Queiroz, Sonia C N; Paraíba, Lourival C; Jonsson, Claudio M; Reyes, Felix G R

2018-04-01

The residue depletion of sulfamethazine (SMZ) was evaluated in tilapia (Oreochromis niloticus) after 11 days of administration of medicated feed containing SMZ, at the dose of 422 mg/kg body weight (bw). The determination of SMZ in feed and tilapia fillet was carried out using the QuEChERS approach for sample preparation, and high performance liquid chromatography with diode array detector (HPLC-DAD) and ultra-high performance liquid chromatography-quadrupole time-of-flight mass spectrometry (UPLC-QToF-MS) for quantitation, respectively. Both methods were validated based on international and Brazilian guidelines and shown to be suitable for the intended purposes. The withdrawal period to reach the maximum residue level (MRL) of 100 μg/kg, according to the European Union (EU) legislative framework to all substances belonging to the sulfonamide (SA) group (EU, 2010), was 10 days (260 °C-day). After treatment, the maximum level of SMZ accumulation in the tilapia muscle was 1.6 mg/kg. SMZ was shown to be quickly excreted by tilapia. Thus, considering the acceptable daily intake of SMZ established by the Codex Commission (0-0.05 mg/kg bw), and a factor of 5 times the upper amount of fish consumption in Brazil (38 kg/year), this study showed that there is a low risk of adverse effects to consumers. This study offers subsidies not only for the establishment of public policies with regard to the use of veterinary drugs currently not allowed in a country by their legal legislative framework for fish farming, but also to fish producers for the proper handling to ensure safe fish fillets. Copyright © 2018 Elsevier Ltd. All rights reserved.

Determining the accuracy of maximum likelihood parameter estimates with colored residuals

NASA Technical Reports Server (NTRS)

Morelli, Eugene A.; Klein, Vladislav

1994-01-01

An important part of building high fidelity mathematical models based on measured data is calculating the accuracy associated with statistical estimates of the model parameters. Indeed, without some idea of the accuracy of parameter estimates, the estimates themselves have limited value. In this work, an expression based on theoretical analysis was developed to properly compute parameter accuracy measures for maximum likelihood estimates with colored residuals. This result is important because experience from the analysis of measured data reveals that the residuals from maximum likelihood estimation are almost always colored. The calculations involved can be appended to conventional maximum likelihood estimation algorithms. Simulated data runs were used to show that the parameter accuracy measures computed with this technique accurately reflect the quality of the parameter estimates from maximum likelihood estimation without the need for analysis of the output residuals in the frequency domain or heuristically determined multiplication factors. The result is general, although the application studied here is maximum likelihood estimation of aerodynamic model parameters from flight test data.

Detection of quinolones in commercial eggs obtained from farms in the Espaíllat Province in the Dominican Republic.

PubMed

Moscoso, S; de los Santos, F Solís; Andino, A G; Diaz-Sanchez, Sandra; Hanning, I

2015-01-01

Previously, we reported the use of quinolones in broiler chickens resulted in residues in retail poultry meat obtained from nine districts in the Santiago Province of the Dominican Republic. Residues in poultry products are a concern due to consumer allergies and the potential to develop antibiotic-resistant bacteria. Given the use of quinolones in poultry production and our previous findings in poultry meat, the objective of this study was to evaluate the presence of quinolone residues in eggs. Samples were collected from 48 different farms located in three of the four municipalities (Moca, Cayetano Germosén, and Jamao) of the Espaíllat Province. Each farm was sampled three times between July and September for a total of 144 samples. Samples were evaluated qualitatively and quantitatively for quinolone residues using the Equinox test. Operation systems (cage or floor), seasonality, and location were considered along with egg-producer sizes that were defined as small scale, <30,000 eggs per day; medium scale, 30,000 to 60,000 eggs per day; or large scale, >60,000 eggs per day. From small-, medium-, and large-scale producers, 69, 50, and 40% of samples were positive for quinolone residues, respectively. A greater number of samples were positive (61%) in floor-laying hen producers compared with those using cages (40%). In the Jamao municipality, 67% of the samples were positive compared with Moca and Cayetano Germosén, where 56 and 25% of samples were positive, respectively. Sampling time had an effect on percent positives: samples collected in July, August, and September were 71, 19, and 63% positive, respectively. Overall, 51% of the samples obtained from eggs produced in the province of Espaíllat were positive for quinolone residues at levels higher than the maximum limits for edible tissue established by the regulatory agencies, including the European Union and U.S. Department of Agriculture. The results obtained from this research confirmed the presence of quinolone residue in eggs, which may present a health risk to some consumers.

OECD Maximum Residue Limit Calculator

EPA Pesticide Factsheets

With the goal of harmonizing the calculation of maximum residue limits (MRLs) across the Organisation for Economic Cooperation and Development, the OECD has developed an MRL Calculator. View the calculator.

Quantitative determination of several synthetic corticosteroids by gas chromatography-mass spectrometry after purification by immunoaffinity chromatography.

PubMed

Delahaut, P; Jacquemin, P; Colemonts, Y; Dubois, M; De Graeve, J; Deluyker, H

1997-08-29

A study was conducted to test a multiresidue analytical procedure for detecting and quantifying several corticosteroids on which the European Union imposes maximum residue limits (MRLs). Primary extracts from different matrices (liver, milk, urine, faeces) were first purified on C18 cartridges. A new immunoaffinity clean-up step was included. The immunoaffinity gel was used to purify several corticosteroids simultaneously with enrichment of the corresponding fractions. The extracts were treated with an aqueous solution of pyridinium chlorochromate to fully oxidise all corticosteroids and to facilitate their extraction with dichloromethane. After evaporation, the final extract was reconstituted with toluene before injection into the GC-MS apparatus. The analysis was performed in the CI-negative ionisation mode using ammonia as the reactant gas. The estimated detection and quantification limits were, respectively, 0.25 and 0.5 ppb or lower. Overall, the method is reproducible to within 20%. Recovery is between 50 and 80% according to the corticosteroid.

Occurrence of antibiotics in mussels and clams from various FAO areas.

PubMed

Chiesa, Luca Maria; Nobile, Maria; Malandra, Renato; Panseri, Sara; Arioli, Francesco

2018-02-01

Filter feeders, like mussels and clams, are suitable bioindicators of environmental pollution. These shellfish, when destined for human consumption, undergo a depuration step that aims to nullify their pathogenic microorganism load and decrease chemical contamination. Nevertheless, the lack of contamination by drugs may not be guaranteed. Antimicrobials are a class of drugs of particular concern due to the increasing phenomenon of antibiotic resistance. Their use in breeding and aquaculture is a major cause of this. We developed a multiclass method for the HPLC-MS/MS analysis of 29 antimicrobials, validated according to the Commission Decision 2002/657/UE guidelines, and applied it to 50 mussel and 50 clam samples derived from various Food and Agricultural Organisation marine zones. The results obtained, indicate a negligible presence of antibiotics. Just one clam sample showed the presence of oxytetracycline at a concentration slightly higher than the European Union Maximum residue limit set for fish. Copyright © 2017. Published by Elsevier Ltd.

Organochlorine pesticide residues in ground water of Thiruvallur district, India.

PubMed

Jayashree, R; Vasudevan, N

2007-05-01

Modern agriculture practices reveal an increase in use of pesticides and fertilizers to meet the food demand of increasing population which results in contamination of the environment. In India crop production increased to 100% but the cropping area has increased marginally by 20%. Pesticides have played a major role in achieving the maximum crop production, but maximum usage and accumulation of pesticide residues was highly detrimental to aquatic and other ecosystem. The present study was chosen to know the level of organochlorines contamination in ground water of Thiruvallur district, Tamil Nadu, India. The samples were highly contaminated with DDT, HCH, endosulfan and their derivatives. Among the HCH derivatives, Gamma HCH residues was found maximum of 9.8 microg/l in Arumbakkam open wells. Concentrations of pp-DDT and op-DDT were 14.3 microg/l and 0.8 microg/l. The maximum residue (15.9 microg/l) of endosulfan sulfate was recorded in Kandigai village bore well. The study showed that the ground water samples were highly contaminated with organochlorine residues.

Pesticide analysis in teas and chamomile by liquid chromatography and gas chromatography tandem mass spectrometry using a modified QuEChERS method: validation and pilot survey in real samples.

PubMed

Lozano, Ana; Rajski, Łukasz; Belmonte-Valles, Noelia; Uclés, Ana; Uclés, Samanta; Mezcua, Milagros; Fernández-Alba, Amadeo R

2012-12-14

This paper presents the validation of a modified QuEChERS method in four matrices - green tea, red tea, black tea and chamomile. The experiments were carried out using blank samples spiked with a solution of 86 pesticides (insecticides, fungicides and herbicides) at four levels - 10, 25, 50 and 100 μg/kg. The samples were extracted according to the citrate QuEChERS protocol; however, to reduce the amount of coextracted matrix compounds, calcium chloride was employed instead of magnesium sulphate in the clean-up step. The samples were analysed by LC-MS/MS and GC-MS/MS. Included in the scope of validation were: recovery, linearity, matrix effects, limits of detection and quantitation as well as intra-day and inter-day precision. The validated method was used in a real sample survey carried out on 75 samples purchased in ten different countries. In all matrices, recoveries of the majority of compounds were in the 70-120% range and were characterised by precision lower than 20%. In 85% of pesticide/matrix combinations the analytes can be detected quantitatively by the proposed method at the European Union Maximum Residue Level. The analysis of the real samples revealed that large number of teas and chamomiles sold in the European Union contain pesticides whose usage is not approved and also pesticides in concentrations above the EU MRLs. Copyright © 2012 Elsevier B.V. All rights reserved.

Numerical Study of Mechanical Response of Pure Titanium during Shot Peening

NASA Astrophysics Data System (ADS)

Wang, Y. M.; Cheng, J. P.; Yang, H. P.; Zhang, C. H.

2018-05-01

Mechanical response of pure titanium impacted by a steel ball was simulated using finite element method to investigate stress and strain evolution during shot peening. It is indicated that biaxial residual stress was obtained in the surface layer while in the interior triaxial residual stress existed because the S33 was comparable to S11 and S22. With decreasing the depth from the top surface, the stress was higher during impacting, but the stress relief extent became more significant when the ball rebounded. Therefore the maximum residual stress was formed in the subsurface layer with depth of 130 μm. As for the residual strain, it is shown that the maximum residual strain LE33 was obtained at the depth of 60 μm corresponding to the maximum shear stress during impacting.

Fast Gas Chromatography with Tandem Mass Spectrometry Analysis of Selected Persistent Organic Pollutants and Organophosphorus and Synthetic Pyrethroid Pesticides in Indian Prawn (Fenneropenaeus indicus) in Compliance with the EU-MRLs.

PubMed

Sawant, Durvesh; Kelkar, Jitendra; Rasam, Pratap; Datar, Ajit; Hase, Prashant; Handique, Dheeraj; Bhone, Ankush; Chiplunkar, Sanket; Hate, Manish

2017-05-01

A fast GC with tandem MS method was developed and validated for multiresidue determination of 95 chemical contaminants (24 synthetic pyrethroids, 17 organochlorines, 17 organophosphorus compounds, 18 polycyclic aromatic hydrocarbons, and 19 polychlorinated biphenyls) in Indian prawns (Fenneropenaeus indicus) as per the European Union maximum residual limit requirements. Chromatographic separation and MS determination were achieved within a short run time of 18 min, without compromising sensitivity and specificity. Our findings revealed a 2.5× reduction in the run time compared with conventional GC methods. Sample preparation involved a QuEChERS-based extraction of 10 g sample with 10 mL acidified acetonitrile (1% acetic acid) and phase separation with 6 g anhydrous magnesium sulfate and 1.5 g sodium acetate. The extract was cleaned in two steps, first by dispersive cleanup with primary secondary amine and then by C18 SPE cartridge. The regression coefficients of linearity (r2) for the concentration range of 5-50 ng/mL were >0.99 for all the compounds. Recoveries at 5 and 10 ng/g levels were within the acceptable range of 70-120%. The repeatability (RSDr) and within-laboratory reproducibility (RSDwR) precisions were ≤20%. The method was successfully applied for analysis of the real world samples for incurred residues.

Residues and dissipation kinetics of carbendazim and diethofencarb in tomato (Lycopersicon esculentum Mill.) and intake risk assessment.

PubMed

Li, Huidong; du, Hongxia; Fang, Liping; Dong, Zhan; Guan, Shuai; Fan, Wenjing; Chen, Zilei

2016-06-01

Dissipation behaviors and residues of carbendazim and diethofencarb in combination in tomato were investigated. The half-lives were 2.1-3.4 days for carbendazim, and 1.8-3.2 days for diethofencarb at a dose of 1.5 times of the recommended dosage. The residues of carbendazim and diethofencarb were below the maximum residue limits (MRLs) in China one day after application of the combination. The ultimate residues were significantly lower than the maximum permissible intake (MPI) in China at the recommended high dose for both child and adult. The values of the maximum dietary exposure for carbendazim and diethofencarb were 0.26 and 0.27 mg per person per day, respectively. The theoretical maximum daily intake (TMDI) values for carbendazim and diethofencarb were 1.5 and 0.5 mg/day, respectively. The dietary exposure was lower than the MPI, which indicates the harvested tomato samples under the experimental conditions (open field) are safe for human consumption at the recommended high dosage of the wettable powder. Copyright © 2016 Elsevier Inc. All rights reserved.

Effectiveness of stress release geometries on reducing residual stress in electroforming metal microstructure

NASA Astrophysics Data System (ADS)

Song, Chang; Du, Liqun; Zhao, Wenjun; Zhu, Heqing; Zhao, Wen; Wang, Weitai

2018-04-01

Micro electroforming, as a mature micromachining technology, is widely used to fabricate metal microdevices in micro electro mechanical systems (MEMS). However, large residual stress in the local positions of the micro electroforming layer often leads to non-uniform residual stress distributions, dimension accuracy defects and reliability issues during fabrication of the metal microdevice. To solve this problem, a novel design method of presetting stress release geometries in the topological structure of the metal microstructure is proposed in this paper. First, the effect of stress release geometries (circular shape, annular groove shape and rivet shape) on the residual stress in the metal microstructure was investigated by finite element modeling (FEM) analysis. Two evaluation parameters, stress concentration factor K T and stress non-uniformity factor δ were calculated. The simulation results show that presetting stress release geometries can effectively reduce and homogenize the residual stress in the metal microstructures were measured metal microstructure. By combined use with stress release geometries of annular groove shape and rivet shape, the stress concentration factor K T and the stress non-uniformity factor δ both decreased at a maximum of 49% and 53%, respectively. Meanwhile, the average residual stress σ avg decreased at a maximum of 20% from  -292.4 MPa to  -232.6 MPa. Then, micro electroforming experiments were carried out corresponding to the simulation models. The residual stresses in the metal microstructures were measured by micro Raman spectroscopy (MRS) method. The results of the experiment proved that the stress non-uniformity factor δ and the average residual stress σ avg also decreased at a maximum with the combination use of annular groove shape and rivet shape stress release geometries, which is in agreement with the results of FEM analysis. The stress non-uniformity factor δ has a maximum decrease of 49% and the average residual stress σ avg has a maximum decrease of 37% from  -257.0 MPa to  -162.0 MPa.

Carry-Over of Aflatoxin B1 to Aflatoxin M1 in High Yielding Israeli Cows in Mid- and Late-Lactation

PubMed Central

Britzi, Malka; Friedman, Shmulik; Miron, Joshua; Solomon, Ran; Cuneah, Olga; Shimshoni, Jakob A.; Soback, Stefan; Ashkenazi, Rina; Armer, Sima; Shlosberg, Alan

2013-01-01

The potent hepatotoxin and carcinogen aflatoxin B1 (AFB1) is a common mycotoxin contaminant of grains used in animal feeds. Aflatoxin M1 (AFM1) is the major metabolite of AFB1 in mammals, being partially excreted into milk, and is a possible human carcinogen. The maximum permitted concentration of AFM1 in cows’ milk is 0.05 μg/kg in Israel and the European Union. Since milk yield and the carry-over of AFB1 in the feed to AFM1 in the milk are highly correlated, it was considered important to determine the AFM1 carry-over in Israeli-Holstein dairy cows, distinguished by world record high milk production. Twelve such cows were used to determine AFM1 carry-over following daily oral administration of feed containing ~86 μg AFB1 for 7 days. The mean carry-over rate at steady-state (Days 3–7) was 5.8% and 2.5% in mid-lactation and late-lactation groups, respectively. The carry-over appears to increase exponentially with milk yield and could be described by the equation: carry-over% = 0.5154 e0.0521 × milk yield, with r2 = 0.6224. If these data truly reflect the carry-over in the national Israeli dairy herd, the maximum level of AFB1 in feed should not exceed 1.4 μg/kg, a value 3.6 times lower than the maximum residue level currently applied in Israel. PMID:23325299

Desorption electrospray ionization mass spectrometry for trace analysis of agrochemicals in food.

PubMed

García-Reyes, Juan F; Jackson, Ayanna U; Molina-Díaz, Antonio; Cooks, R Graham

2009-01-15

Desorption electrospray ionization (DESI) is applied to the rapid, in situ, direct qualitative and quantitative (ultra)trace analysis of agrochemicals in foodstuffs. To evaluate the potential of DESI mass spectrometry (MS) in toxic residue testing in food, 16 representative multiclass agricultural chemicals (pesticides, insecticides, herbicides, and fungicides) were selected (namely, ametryn, amitraz, azoxystrobin, bitertanol, buprofezin, imazalil, imazalil metabolite, isofenphos-methyl, malathion, nitenpyram, prochloraz, spinosad, terbuthylazine, thiabendazole, and thiacloprid). The DESI-MS experiments were performed using 3 microL of solution spotted onto conventional smooth poly(tetrafluoroethylene) (PTFE) surfaces, with examination by MS and tandem mass spectrometry (MS/MS) using an ion trap mass spectrometer. Optimization of the spray solvent led to the use of acetonitrile/water (80:20) (v/v), with 1% formic acid. Most of the compounds tested showed remarkable sensitivity in the positive ion mode, approaching that attainable with conventional direct infusion electrospray mass spectrometry. To evaluate the potential of the proposed approach in real samples, different experiments were performed including the direct DESI-MS/MS analysis of fruit peels and also of fruit/vegetable extracts. The results proved that DESI allows the detection and confirmation of traces of agrochemicals in actual market-purchased samples. In addition, MS/MS confirmation of selected pesticides in spiked vegetable extracts was obtained at absolute levels as low as 1 pg for ametryn. Quantitation of imazalil residues was also undertaken using an isotopically labeled standard. The data obtained were in agreement with those from the liquid chromatography mass spectrometry (LC-MS) reference method, with relative standard deviation (RSD) values consistently below 15%. The results obtained demonstrate the sensitivity of DESI as they meet the stringent European Union pesticide regulation requirements (maximum residue levels) for a large percentage of the studied compounds.

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray.

PubMed

Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras-Ramírez, María Elena; Lara-Álvarez, Carlos; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

2016-01-01

In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg).

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray

PubMed Central

Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras–Ramírez, María Elena; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

2016-01-01

In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg). PMID:27092938

Parametric study on single shot peening by dimensional analysis method incorporated with finite element method

NASA Astrophysics Data System (ADS)

Wu, Xian-Qian; Wang, Xi; Wei, Yan-Peng; Song, Hong-Wei; Huang, Chen-Guang

2012-06-01

Shot peening is a widely used surface treatment method by generating compressive residual stress near the surface of metallic materials to increase fatigue life and resistance to corrosion fatigue, cracking, etc. Compressive residual stress and dent profile are important factors to evaluate the effectiveness of shot peening process. In this paper, the influence of dimensionless parameters on maximum compressive residual stress and maximum depth of the dent were investigated. Firstly, dimensionless relations of processing parameters that affect the maximum compressive residual stress and the maximum depth of the dent were deduced by dimensional analysis method. Secondly, the influence of each dimensionless parameter on dimensionless variables was investigated by the finite element method. Furthermore, related empirical formulas were given for each dimensionless parameter based on the simulation results. Finally, comparison was made and good agreement was found between the simulation results and the empirical formula, which shows that a useful approach is provided in this paper for analyzing the influence of each individual parameter.

Total and inorganic arsenic in Iranian rice.

PubMed

Cano-Lamadrid, Marina; Munera-Picazo, Sandra; Burló, Francisco; Hojjati, Mohammad; Carbonell-Barrachina, Ángel A

2015-05-01

It is well known that arsenic (As) exposure, particularly to inorganic species (i-As), has adverse effects on humans. Nowadays, the European Union (EU) has still not regulated the maximum residue limit of As in commercial samples of rice and rice-based products, although it is actively working on the topic. The European Food Safety Authority (EFSA) is collecting data on total arsenic (t-As) and i-As from different rice-producing regions not only from EU countries but also from other parts of the world to finally set up this maximum threshold. As Iran is a rice-producing country, the aim of this work was to evaluate the contents of t-As and i-As in 15 samples of Iranian white, nonorganic, and aromatic rice collected from the most important rice-producing regions of the country. The means of t-As and i-As were 120 and 82 μg/kg, respectively. The experimental i-As mean in Iranian rice was below the Chinese standard for the i-As in rice, 150 μg/kg, and the Food and Agriculture Organization of the United Nations (FAO) limit, 200 μg/kg. Therefore, Iranian rice seems to have reasonable low i-As content and it is safe to be marketed in any market, including China and the EU. © 2015 Institute of Food Technologists®

Laser quench hardening of steel: Effects of superimposed elastic pre-stress on the hardness and residual stress distribution

NASA Astrophysics Data System (ADS)

Meserve, Justin

Cold drawn AISI 4140 beams were LASER surface hardened with a 2 kW CO2 LASER. Specimens were treated in the free state and while restrained in a bending fixture inducing surface tensile stresses of 94 and 230 MPa. Knoop hardness indentation was used to evaluate the through thickness hardness distribution, and a layer removal methodology was used to evaluate the residual stress distribution. Results showed the maximum surface hardness attained was not affected by pre-stress during hardening, and ranged from 513 to 676 kg/mm2. The depth of effective hardening varied at different magnitudes of pre-stress, but did not vary proportionately to the pre-stress. The surface residual stress, coinciding with the maximum compressive residual stress, increased as pre-stress was increased, from 1040 MPa for the nominally treated specimens to 1270 MPa for specimens pre-stressed to 230 MPa. The maximum tensile residual stress observed in the specimens decreased from 1060 MPa in the nominally treated specimens to 760 MPa for specimens pre-stressed to 230 MPa. Similarly, thickness of the compressive residual stress region increased and the depth at which maximum tensile residual stress occurred increased as the pre-stress during treatment was increased Overall, application of tensile elastic pre-stress during LASER hardening is beneficial to the development of compressive residual stress in AISI 4140, with minimal impact to the hardness attained from the treatment. The newly developed approach for LASER hardening may support efforts to increase both the wear and fatigue resistance of parts made from hardenable steels.

Effects on health, performance, and tissue residues of the ionophore antibiotic salinomycin in finishing broilers (21 to 38 d).

PubMed

Diaz, Gonzalo J; Aguillón, Yandy; Cortés, Amparo

2018-06-01

A study was conducted to evaluate the effects of feeding salinomycin at the recommended prophylactic level, and at 2 and 3 times this level, to finishing male broilers (d 21 to 38). Four treatment groups were given the experimental diets containing 0, 60, 120, or 180 parts per million (ppm) salinomycin from d 21 to 38. Performance, relative organ weights, selected serum enzymes, and salinomycin residues in liver, muscle, and serum were determined. Salinomycin supplementation had no effect on body weight, feed intake, or feed conversion, and caused no overt signs of toxicity. After a week of being fed the salinomycin diets, the serum activity of aspartate aminotransferase was significantly increased in chickens fed 180 ppm compared with controls. These birds also showed microscopic lesions in breast and thigh muscles, but not in cardiac muscle. Salinomycin residues were not detected by high-performance liquid chromatography coupled to tandem mass spectrometry in liver or muscle samples from the birds fed 0, 60, or 120 ppm salinomycin. However, chickens fed 180 ppm salinomycin had detectable levels in liver and muscle above the maximum residue level of 5 μg/kg established by the European Union. All birds fed salinomycin had salinomycin in their sera with levels ranging from N.D. (not detected) in the controls to 24.4 ± 7.9, 61.4 ± 18.9, and 94.5 ± 9.1 μg/L for salinomycin dietary levels of 60, 120, and 180 ppm, respectively. Serum salinomycin concentration was linearly related with salinomycin content in feed (y = 0.584x - 10, r2 = 0.999). The results showed that even at 3 times the prophylactic level, salinomycin does not induce clinical toxicosis or mortality. No salinomycin residues were found in edible tissues at the recommended dietary level or at 2 times this level. However, salinomycin was detected in serum regardless of the dietary level. A simple method for salinomycin determination in serum is described which can be used as a marker of exposure and/or to predict levels in the diet.

New materials for solid-phase extraction and multiclass high-performance liquid chromatographic analysis of pesticides in grapes.

PubMed

Melo, Lucio F C; Collins, Carol H; Jardim, Isabel C S F

2004-04-02

Sample preparation procedures which included the use of new aminopropyl (NH2) and octadecyl (C18) solid-phase extraction (SPE) sorbents are proposed for the simultaneous multiclass determination of the fungicide benomyl and of the herbicides tebuthiuron, diuron, simazine, atrazine, and ametryn in grapes, using single wavelength high-performance liquid chromatography. Sorbent preparation uses a fast, easy, and effective procedure to obtain silica-based materials, made by depositing polysiloxanes on a silica support followed by thermal immobilization. Recovery results of the compounds, after elution from the SPE cartridges, indicate that the most efficient system employed silica loaded with 40% of an aminofunctional polydimethylsiloxane as sorbent, using dichloromethane:methanol (95:5, v/v) as eluent. Method validation, carried out in agreement with International Conference on Harmonization directives, was performed at three fortification levels (100, 200, and 1000 microg kg(-1)). Limits of detection and quantification show that the method developed can be used to detect the pesticides at concentrations below the maximum residue levels established by Codex Alimentarius, the US Environmental Protection Agency, the European Union, and Brazilian legislation.

Quantitative analysis of amoxicillin, its major metabolites and ampicillin in eggs by liquid chromatography combined with electrospray ionization tandem mass spectrometry.

PubMed

Sun, Lirui; Jia, Longfei; Xie, Xing; Xie, Kaizhou; Wang, Jianfeng; Liu, Jianyu; Cui, Lulu; Zhang, Genxi; Dai, Guojun; Wang, Jinyu

2016-02-01

In this present study, we developed a simple, rapid and specific method for the quantitative analysis of the contents of amoxicillin (AMO), AMO metabolites and ampicillin (AMP) in eggs. This method uses a simple liquid-liquid extraction with acetonitrile followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The optimized method has been validated according to requirements defined by the European Union and Food and Drug Administration. Extraction recoveries of the target compounds from the egg at 5, 10 and 25 μg/kg were all higher than 80%, with relative standard deviations not exceeding 10.00%. The limits of quantification in eggs were below the maximum residue limits (MRLs). The decision limits (CCα) ranged between 11.1 and 11.5 μg/kg, while detection capabilities (CCβ) from 12.1 to 13.0 μg/kg. These values were very close to the corresponding MRLs. Finally, the new approach was successfully verified for the quantitative determination of these analytes in 40 commercial eggs from local supermarkets. Copyright © 2015 Elsevier Ltd. All rights reserved.

Flow injection analysis of nitrate and nitrite in commercial baby foods.

PubMed

Chetty, Adrian A; Prasad, Surendra

2016-04-15

Commercial baby foods are an easy alternative to home-made meals especially for working parents in a nuclear family therefore it is imperative to determine the nitrate and nitrite content in commercially available baby foods varieties marketed in Fiji. A total of 108 baby food samples were analyzed for nitrate and nitrite using our standardized flow injection analysis (FIA) technique with colorimetric detection technique employing sulfanilamide and N-(1-naphthyl)ethylenediamine dihydrochloride as color reagents where the samples throughput was 38 h(-1). The commercial baby food varieties chosen comprised of vegetables, cereals, fruits and milk. The study shows that the nitrate content of the baby foods studied ranges from 2.10 to 220.67 mg kg(-1) whereas the nitrite content ranges from 0.44 to 3.67 mg kg(-1). Typical recoveries of spiked nitrate residues ranged from 92% to 106%. The study shows that the average nitrate content of commercially available baby foods in Fiji descends below the maximum level proposed by the European Union Legislation. Copyright © 2015 Elsevier Ltd. All rights reserved.

9,10-Anthraquinone deposit in tea plantation might be one of the reasons for contamination in tea.

PubMed

Wang, Xuan; Zhou, Li; Luo, Fengjian; Zhang, Xinzhong; Sun, Hezhi; Yang, Mei; Lou, Zhengyun; Chen, Zongmao

2018-04-01

9,10-Anthraquinone (AQ) was a new contaminant, with unknown sources, occurred globally in tea. European Union (EU) fixed the maximum residue limit (MRL) of 0.02mg/kg. The pollution source of AQ in tea was traced from the view of AQ deposit on tea crop by simulation. The possible contamination pathway and main factors to decrease AQ were explored in tea cultivation- tea manufacture- tea infusion, on the basis of AQ analytical methods by using solvent extraction and gas chromatography-tandem mass spectrometry (GC-MS/MS) quantification. 58.8-84.6% of AQ degraded in tea processing, and drying played a key role to reduce the AQ contamination. Certain concentration of AQ deposited on tea shoots could resulted in AQ beyond the MRL of 0.02mg/kg in tea. AQ leaching into tea brew (about 10%) could lead to the possible health risk. AQ deposit on tea crop during the tea cultivation might cause the AQ contamination in tea. Copyright © 2017. Published by Elsevier Ltd.

On the residual stress modeling of shot-peened AISI 4340 steel: finite element and response surface methods

NASA Astrophysics Data System (ADS)

Asgari, Ali; Dehestani, Pouya; Poruraminaie, Iman

2018-02-01

Shot peening is a well-known process in applying the residual stress on the surface of industrial parts. The induced residual stress improves fatigue life. In this study, the effects of shot peening parameters such as shot diameter, shot speed, friction coefficient, and the number of impacts on the applied residual stress will be evaluated. To assess these parameters effect, firstly the shot peening process has been simulated by finite element method. Then, effects of the process parameters on the residual stress have been evaluated by response surface method as a statistical approach. Finally, a strong model is presented to predict the maximum residual stress induced by shot peening process in AISI 4340 steel. Also, the optimum parameters for the maximum residual stress are achieved. The results indicate that effect of shot diameter on the induced residual stress is increased by increasing the shot speed. Also, enhancing the friction coefficient magnitude always cannot lead to increase in the residual stress.

Origins of tropospheric ozone interannual variation over Réunion: A model investigation

NASA Astrophysics Data System (ADS)

Liu, Junhua; Rodriguez, Jose M.; Thompson, Anne M.; Logan, Jennifer A.; Douglass, Anne R.; Olsen, Mark A.; Steenrod, Stephen D.; Posny, Françoise

2016-01-01

Observations from long-term ozonesonde measurements show robust variations and trends in the evolution of ozone in the middle and upper troposphere over Réunion Island (21.1°S, 55.5°E) in June-August. Here we examine possible causes of the observed ozone variation at Réunion Island using hindcast simulations by the stratosphere-troposphere Global Modeling Initiative chemical transport model for 1992-2014, driven by assimilated Modern-Era Retrospective Analysis for Research and Applications meteorological fields. Réunion Island is at the edge of the subtropical jet, a region of strong stratospheric-tropospheric exchange. Our analysis implies that the large interannual variation (IAV) of upper tropospheric ozone over Réunion is driven by the large IAV of the stratospheric influence. The IAV of the large-scale, quasi-horizontal wind patterns also contributes to the IAV of ozone in the upper troposphere. Comparison to a simulation with constant emissions indicates that increasing emissions do not lead to the maximum trend in the middle and upper troposphere over Réunion during austral winter implied by the sonde data. The effects of increasing emission over southern Africa are limited to the lower troposphere near the surface in August-September.

Relationship Between Maximum Aerobic Speed Performance and Distance Covered in Rugby Union Games.

PubMed

Swaby, Rick; Jones, Paul A; Comfort, Paul

2016-10-01

Swaby, R, Jones, PA, and Comfort, P. Relationship between maximum aerobic speed performance and distance covered in rugby union games. J Strength Cond Res 30(10): 2788-2793, 2016-Researchers have shown a clear relationship between aerobic fitness and the distance covered in professional soccer, although no research has identified such a relationship in rugby union. Therefore, the aim of the study was to identify whether there was a relationship between maximal aerobic speed (MAS) and the distance covered in rugby union games. Fourteen professional rugby union players (age = 26 ± 6 years, height = 1.90 ± 0.12 m, mass = 107.1 ± 24.1 kg) participated in this investigation. Each player performed a MAS test on 3 separate occasions during the preseason, to determine reliability and provide baseline data, and participated in 6 competitive games during the early stages of the season. Game data were collected using global positioning system technology. No significant difference (p > 0.05) in total distance covered was observed between games. Relationships between players' MAS and the average distance covered from 6 competitive games were explored using Pearson's correlation coefficients, with MAS performance showing a strong relationship with distance covered during match play (r = 0.746, p < 0.001). Significantly greater (p = 0.001, Cohen's d = 2.29) distances were covered by backs (6,544 ± 573 m) compared with the forwards (4,872 ± 857 m) during a game. Similarly, backs recorded a significantly (p = 0.001, Cohen's d = 2.20) higher MAS (4.9 ± 0.13 m·s) compared with the forwards (4.2 ± 0.43 m·s). Results of the study illustrate the importance of developing high levels of aerobic fitness to increase the distance that the athlete covers in the game.

Estuarine River Data for the Ten Thousand Islands Area, Florida, Water Year 2005

USGS Publications Warehouse

Byrne, Michael J.; Patino, Eduardo

2008-01-01

The U.S. Geological Survey collected stream discharge, stage, salinity, and water-temperature data near the mouths of 11 tributaries flowing into the Ten Thousand Islands area of Florida from October 2004 to June 2005. Maximum positive discharge from Barron River and Faka Union River was 6,000 and 3,200 ft3/s, respectively; no other tributary exceeded 2,600 ft3/s. Salinity variation was greatest at Barron River and Faka Union River, ranging from 2 to 37 ppt, and from 3 to 34 ppt, respectively. Salinity maximums were greatest at Wood River and Little Wood River, each exceeding 40 ppt. All data were collected prior to the commencement of the Picayune Strand Restoration Project, which is designed to establish a more natural flow regime to the tributaries of the Ten Thousand Islands area.

Predicting protein β-sheet contacts using a maximum entropy-based correlated mutation measure.

PubMed

Burkoff, Nikolas S; Várnai, Csilla; Wild, David L

2013-03-01

The problem of ab initio protein folding is one of the most difficult in modern computational biology. The prediction of residue contacts within a protein provides a more tractable immediate step. Recently introduced maximum entropy-based correlated mutation measures (CMMs), such as direct information, have been successful in predicting residue contacts. However, most correlated mutation studies focus on proteins that have large good-quality multiple sequence alignments (MSA) because the power of correlated mutation analysis falls as the size of the MSA decreases. However, even with small autogenerated MSAs, maximum entropy-based CMMs contain information. To make use of this information, in this article, we focus not on general residue contacts but contacts between residues in β-sheets. The strong constraints and prior knowledge associated with β-contacts are ideally suited for prediction using a method that incorporates an often noisy CMM. Using contrastive divergence, a statistical machine learning technique, we have calculated a maximum entropy-based CMM. We have integrated this measure with a new probabilistic model for β-contact prediction, which is used to predict both residue- and strand-level contacts. Using our model on a standard non-redundant dataset, we significantly outperform a 2D recurrent neural network architecture, achieving a 5% improvement in true positives at the 5% false-positive rate at the residue level. At the strand level, our approach is competitive with the state-of-the-art single methods achieving precision of 61.0% and recall of 55.4%, while not requiring residue solvent accessibility as an input. http://www2.warwick.ac.uk/fac/sci/systemsbiology/research/software/

Statistical Techniques to Analyze Pesticide Data Program Food Residue Observations.

PubMed

Szarka, Arpad Z; Hayworth, Carol G; Ramanarayanan, Tharacad S; Joseph, Robert S I

2018-06-26

The U.S. EPA conducts dietary-risk assessments to ensure that levels of pesticides on food in the U.S. food supply are safe. Often these assessments utilize conservative residue estimates, maximum residue levels (MRLs), and a high-end estimate derived from registrant-generated field-trial data sets. A more realistic estimate of consumers' pesticide exposure from food may be obtained by utilizing residues from food-monitoring programs, such as the Pesticide Data Program (PDP) of the U.S. Department of Agriculture. A substantial portion of food-residue concentrations in PDP monitoring programs are below the limits of detection (left-censored), which makes the comparison of regulatory-field-trial and PDP residue levels difficult. In this paper, we present a novel adaption of established statistical techniques, the Kaplan-Meier estimator (K-M), the robust regression on ordered statistic (ROS), and the maximum-likelihood estimator (MLE), to quantify the pesticide-residue concentrations in the presence of heavily censored data sets. The examined statistical approaches include the most commonly used parametric and nonparametric methods for handling left-censored data that have been used in the fields of medical and environmental sciences. This work presents a case study in which data of thiamethoxam residue on bell pepper generated from registrant field trials were compared with PDP-monitoring residue values. The results from the statistical techniques were evaluated and compared with commonly used simple substitution methods for the determination of summary statistics. It was found that the maximum-likelihood estimator (MLE) is the most appropriate statistical method to analyze this residue data set. Using the MLE technique, the data analyses showed that the median and mean PDP bell pepper residue levels were approximately 19 and 7 times lower, respectively, than the corresponding statistics of the field-trial residues.

40 CFR 141.66 - Maximum contaminant levels for radionuclides.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Maximum contaminant levels for... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.66 Maximum contaminant levels for radionuclides. (a) [Reserved] (b) MCL for combined radium-226 and -228. The maximum...

40 CFR 141.66 - Maximum contaminant levels for radionuclides.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Maximum contaminant levels for... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.66 Maximum contaminant levels for radionuclides. (a) [Reserved] (b) MCL for combined radium-226 and -228. The maximum...

40 CFR 141.66 - Maximum contaminant levels for radionuclides.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Maximum contaminant levels for... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.66 Maximum contaminant levels for radionuclides. (a) [Reserved] (b) MCL for combined radium-226 and -228. The maximum...

40 CFR 141.66 - Maximum contaminant levels for radionuclides.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Maximum contaminant levels for... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.66 Maximum contaminant levels for radionuclides. (a) [Reserved] (b) MCL for combined radium-226 and -228. The maximum...

Emission of Carbon Dioxide Influenced by Different Water Levels from Soil Incubated Organic Residues

PubMed Central

Hossain, M. B.; Puteh, A. B.

2013-01-01

We studied the influence of different organic residues and water levels on decomposition rate and carbon sequestration in soil. Organic residues (rice straw, rice root, cow dung, and poultry litter) including control were tested under moistened and flooding systems. An experiment was laid out as a complete randomized design at 25°C for 120 days. Higher CO2-C (265.45 mg) emission was observed in moistened condition than in flooding condition from 7 to 120 days. Among the organic residues, poultry litter produced the highest CO2-C emission. Poultry litter with soil mixture increased 121% cumulative CO2-C compared to control. On average, about 38% of added poultry litter C was mineralized to CO2-C. Maximum CO2-C was found in 7 days after incubation and thereafter CO2-C emission was decreased with the increase of time. Control produced the lowest CO2-C (158.23 mg). Poultry litter produced maximum cumulative CO2-C (349.91 mg). Maximum organic carbon was obtained in cow dung which followed by other organic residues. Organic residues along with flooding condition decreased cumulative CO2-C, k value and increased organic C in soil. Maximum k value was found in poultry litter and control. Incorpored rice straw increased organic carbon and decreased k value (0.003 g d−1) in soil. In conclusion, rice straw and poultry litter were suitable for improving soil carbon. PMID:24163626

Energy from Biomass for Sustainable Cities

NASA Astrophysics Data System (ADS)

Panepinto, D.; Zanetti, M. C.; Gitelman, L.; Kozhevnikov, M.; Magaril, E.; Magaril, R.

2017-06-01

One of the major challenges of sustainable urban development is ensuring a sustainable energy supply while minimizing negative environmental impacts. The European Union Directive 2009/28/EC has set a goal of obtaining 20 percent of all energy from renewable sources by 2020. In this context, it is possible to consider the use of residues from forest maintenance, residues from livestock, the use of energy crops, the recovery of food waste, and residuals from agro-industrial activities. At the same time, it is necessary to consider the consequent environmental impact. In this paper an approach in order to evaluate the environmental compatibility has presented. The possibilities of national priorities for commissioning of power plants on biofuel and other facilities of distributed generation are discussed.

Nominate a Codex MRL

EPA Pesticide Factsheets

The Codex Committee on Pesticide Residues (CCPR) is responsible for establishing maximum residue limits (MRLs) for pesticide residues in specific food items or in groups of food for Codex. Learn how to submit a request for a CODEX MRL.

7 CFR 29.427 - Pesticide residue standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

7 CFR 29.427 - Pesticide residue standards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

7 CFR 29.427 - Pesticide residue standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

7 CFR 29.427 - Pesticide residue standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

7 CFR 29.427 - Pesticide residue standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

Neonicotinoid residues in UK honey despite European Union moratorium

PubMed Central

Ridding, Lucy; Freeman, Stephen N.; Pereira, M. Gloria; Sleep, Darren; Redhead, John; Aston, David; Carreck, Norman L.; Shore, Richard F.; Bullock, James M.; Heard, Matthew S.; Pywell, Richard F.

2018-01-01

Due to concerns over negative impacts on insect pollinators, the European Union has implemented a moratorium on the use of three neonicotinoid pesticide seed dressings for mass-flowering crops. We assessed the effectiveness of this policy in reducing the exposure risk to honeybees by collecting 130 samples of honey from bee keepers across the UK before (2014: N = 21) and after the moratorium was in effect (2015: N = 109). Neonicotinoids were present in about half of the honey samples taken before the moratorium, and they were present in over a fifth of honey samples following the moratorium. Clothianidin was the most frequently detected neonicotinoid. Neonicotinoid concentrations declined from May to September in the year following the ban. However, the majority of post-moratorium neonicotinoid residues were from honey harvested early in the year, coinciding with oilseed rape flowering. Neonicotinoid concentrations were correlated with the area of oilseed rape surrounding the hive location. These results suggest mass flowering crops may contain neonicotinoid residues where they have been grown on soils contaminated by previously seed treated crops. This may include winter seed treatments applied to cereals that are currently exempt from EU restrictions. Although concentrations of neonicotinoids were low (<2.0 ng g-1), and posed no risk to human health, they may represent a continued risk to honeybees through long-term chronic exposure. PMID:29298300

40 CFR 141.55 - Maximum contaminant level goals for radionuclides.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for... PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level Goals and Maximum Residual Disinfectant Level Goals § 141.55 Maximum contaminant level goals for radionuclides...

40 CFR 141.55 - Maximum contaminant level goals for radionuclides.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Maximum contaminant level goals for... PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level Goals and Maximum Residual Disinfectant Level Goals § 141.55 Maximum contaminant level goals for radionuclides...

Residues in Beeswax: A Health Risk for the Consumer of Honey and Beeswax?

PubMed

Wilmart, Olivier; Legrève, Anne; Scippo, Marie-Louise; Reybroeck, Wim; Urbain, Bruno; de Graaf, Dirk C; Steurbaut, Walter; Delahaut, Philippe; Gustin, Pascal; Nguyen, Bach Kim; Saegerman, Claude

2016-11-09

A scenario analysis in regard to the risk of chronic exposure of consumers to residues through the consumption of contaminated honey and beeswax was conducted. Twenty-two plant protection products and veterinary substances of which residues have already been detected in beeswax in Europe were selected. The potential chronic exposure was assessed by applying a worst-case scenario based on the addition of a "maximum" daily intake through the consumption of honey and beeswax to the theoretical maximum daily intake through other foodstuffs. For each residue, the total exposure was finally compared to the acceptable daily intake. It is concluded that the food consumption of honey and beeswax contaminated with these residues considered separately does not compromise the consumer's health, provided proposed action limits are met. In regard to residues of flumethrin in honey and in beeswax, "zero tolerance" should be applied.

Trends in the management of residual municipal solid waste.

PubMed

Rada, E C; Istrate, I A; Ragazzi, M

2009-06-01

In agreement with European Union directives, the integrated management of municipal solid waste must be developed ensuring a balanced relationship between the streams of selective collection and the one regarding the residual waste. A theoretical scenario is made where the residual municipal solid waste is composed only of non-recyclable fractions. An important aspect concerns the role of the organic fraction as selective collection can significantly decrease its content in the residual waste. This paper focuses on the planning, design and management consequences of this unsteady scenario. The treatments that are considered are: combustion, gasification, pyrolysis, integrated thermal plants, aerobic mechanical-biological treatments, anaerobic mechanical-biological treatments and other types of treatment. The considerations are based on the experience of the authors not only in terms of development of research but also in terms of transfer of the research results to the real scale, and knowledge of the state-of-the-art of the sector.

Origins of tropospheric ozone interannual variation (IAV) over Réunion: A model investigation.

PubMed

Liu, Junhua; Rodriguez, Jose M; Thompson, Anne M; Logan, Jennifer A; Douglass, Anne R; Olsen, Mark A; Steenrod, Stephen D; Posny, Francoise

2016-01-16

Observations from long-term ozonesonde measurements show robust variations and trends in the evolution of ozone in the middle and upper troposphere over Réunion Island (21.1°S, 55.5°E) in June-August. Here we examine possible causes of the observed ozone variation at Réunion Island using hindcast simulations by the stratosphere-troposphere Global Modeling Initiative chemical transport model (GMI-CTM) for 1992-2014, driven by assimilated Modern-Era Retrospective Analysis for Research and Applications (MERRA) meteorological fields. Réunion Island is at the edge of the subtropical jet, a region of strong stratospheric-tropospheric exchange (STE). Our analysis implies that the large interannual variation (IAV) of upper tropospheric ozone over Réunion is driven by the large IAV of the stratospheric influence. The IAV of the large-scale, quasi-horizontal wind patterns also contributes to the IAV of ozone in the upper troposphere. Comparison to a simulation with constant emissions indicates that increasing emissions do not lead to the maximum trend in the middle and upper troposphere over Réunion during austral winter implied by the sonde data. The effects of increasing emission over southern Africa are limited to the lower troposphere near the surface in August - September.

Origins of tropospheric ozone interannual variation (IAV) over Réunion: A model investigation

PubMed Central

Liu, Junhua; Rodriguez, Jose M.; Thompson, Anne M.; Logan, Jennifer A.; Douglass, Anne R.; Olsen, Mark A.; Steenrod, Stephen D.; Posny, Francoise

2018-01-01

Observations from long-term ozonesonde measurements show robust variations and trends in the evolution of ozone in the middle and upper troposphere over Réunion Island (21.1°S, 55.5°E) in June-August. Here we examine possible causes of the observed ozone variation at Réunion Island using hindcast simulations by the stratosphere-troposphere Global Modeling Initiative chemical transport model (GMI-CTM) for 1992–2014, driven by assimilated Modern-Era Retrospective Analysis for Research and Applications (MERRA) meteorological fields. Réunion Island is at the edge of the subtropical jet, a region of strong stratospheric-tropospheric exchange (STE). Our analysis implies that the large interannual variation (IAV) of upper tropospheric ozone over Réunion is driven by the large IAV of the stratospheric influence. The IAV of the large-scale, quasi-horizontal wind patterns also contributes to the IAV of ozone in the upper troposphere. Comparison to a simulation with constant emissions indicates that increasing emissions do not lead to the maximum trend in the middle and upper troposphere over Réunion during austral winter implied by the sonde data. The effects of increasing emission over southern Africa are limited to the lower troposphere near the surface in August – September. PMID:29657911

Evaluation of the Charm maximum residue limit β-lactam and tetracycline test for the detection of antibiotics in ewe and goat milk.

PubMed

Beltrán, M C; Romero, T; Althaus, R L; Molina, M P

2013-05-01

The Charm maximum residue limit β-lactam and tetracycline test (Charm MRL BLTET; Charm Sciences Inc., Lawrence, MA) is an immunoreceptor assay utilizing Rapid One-Step Assay lateral flow technology that detects β-lactam or tetracycline drugs in raw commingled cow milk at or below European Union maximum residue levels (EU-MRL). The Charm MRL BLTET test procedure was recently modified (dilution in buffer and longer incubation) by the manufacturers to be used with raw ewe and goat milk. To assess the Charm MRL BLTET test for the detection of β-lactams and tetracyclines in milk of small ruminants, an evaluation study was performed at Instituto de Ciencia y Tecnologia Animal of Universitat Politècnica de València (Spain). The test specificity and detection capability (CCβ) were studied following Commission Decision 2002/657/EC. Specificity results obtained in this study were optimal for individual milk free of antimicrobials from ewes (99.2% for β-lactams and 100% for tetracyclines) and goats (97.9% for β-lactams and 100% for tetracyclines) along the entire lactation period regardless of whether the results were visually or instrumentally interpreted. Moreover, no positive results were obtained when a relatively high concentration of different substances belonging to antimicrobial families other than β-lactams and tetracyclines were present in ewe and goat milk. For both types of milk, the CCβ calculated was lower or equal to EU-MRL for amoxicillin (4 µg/kg), ampicillin (4 µg/kg), benzylpenicillin (≤ 2 µg/kg), dicloxacillin (30 µg/kg), oxacillin (30 µg/kg), cefacetrile (≤ 63 µg/kg), cefalonium (≤ 10 µg/kg), cefapirin (≤ 30 µg/kg), desacetylcefapirin (≤ 30 µg/kg), cefazolin (≤ 25 µg/kg), cefoperazone (≤ 25 µg/kg), cefquinome (20 µg/kg), ceftiofur (≤ 50 µg/kg), desfuroylceftiofur (≤ 50µg/kg), and cephalexin (≤ 50 µg/kg). However, this test could neither detect cloxacillin nor nafcillin at or below EU-MRL (CCβ >30 µg/kg). The CCβ for tetracyclines was also lower than EU-MRL for chlortetracycline (ewe milk: ≤ 50 µg/kg; goat milk: 75 µg/kg), oxytetracycline (≤ 50 µg/kg), and tetracycline (≤ 50 µg/kg). Regarding the 4-epimers of these tetracyclines only 4-epioxytetracycline was detected by the Charm MRL BLTET test below EU-MRL (ewe milk: 75 µg/kg; goat milk: ≤ 50 µg/kg). Acidiol had no effect on the performance of the test. The Charm MRL BLTET test could be used routinely with adapted test procedure for the fast screening of ewe and goat milk. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Regulations applicable to plant food supplements and related products in the European Union.

PubMed

Silano, Vittorio; Coppens, Patrick; Larrañaga-Guetaria, Ainhoa; Minghetti, Paola; Roth-Ehrang, René

2011-12-01

This paper deals with the current regulatory and legal settings of traditional plant food supplements and herbal medicinal products in the European Union (EU). Marketing of botanicals in foods and food supplements in the EU is subject to several provisions of food law, which cover aspects of safety, production, labelling and product composition, including the use of additives and maximum levels of contaminants and residues. However, due to limited harmonization at the EU level, specific national regulations adopted at a Member State level also apply and mutual recognition is the mechanism through which such products can be marketed in EU countries other than those of origin. Unlike food supplements, marketing of traditional herbal medicinal products is regulated by an ad hoc Directive (i.e. Directive 2004/24/EC) covering in detail all the relevant aspects of these products, including a facilitated registration procedure at national level. However, by distinguishing traditional herbal medicinal products from plant food supplements and establishing selective marketing modalities for these two product categories, the EU has been confronted with implementation difficulties for traditional herbal medicinal products and a lack of homogeneity in the regulatory approaches adopted in different EU Member States. In fact, currently the nature of the commercial botanical products made available to consumers as traditional medicinal products or food supplements, depends largely on the EU Member State under consideration as a consequence of how competent National Authorities and manufacturing companies interpret and apply current regulations rather than on the intrinsic properties of the botanical products and their constituents. When the EU approach is compared with approaches adopted in some non-European countries to regulate these product categories, major differences become evident.

Opportunities and Barriers to Resource Recovery and Recycling from Shredder Residue in the United States

NASA Astrophysics Data System (ADS)

Nayak, Naren; Apelian, Diran

2014-11-01

Shredder residue is the by-product remaining after ferrous and nonferrous metals have been recovered from the processing of vehicles, white goods, and peddler scrap. Shredder residue consists of glass, plastics, rubber, dirt, and small amounts of metal. It is estimated that 5-7 million tons of this shredder residue are landfilled each year in the United States. Technical advancements, coupled with European Union directives and the economic climate, have transformed the recycling of shredder residue in Europe. In the United States, however, regulatory controls and the cheap cost of landfill have worked against the advancement of recycling and recovery of this resource. The Argonne National Laboratory, which is funded by the U.S. Department of Energy, has investigated the effectiveness of recycling shredder residue into polymers. Other research has examined the use of shredder residue in waste-to-energy applications. To improve our ability to process and recycle shredder residue, an investigation of the regulatory, economic, and technological challenges was undertaken. The objective was to conduct a comprehensive review of work done to date, to document the composition of typical shredder output and to identify potential recoverable items (residual metals, plastics, rubber, foam, etc.). Along with uncovering potential new markets, the research would identify the technical, regulatory, and economic barriers to developing those markets.

40 CFR 180.505 - Emamectin; tolerances for residues.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Emamectin; tolerances for residues... § 180.505 Emamectin; tolerances for residues. (a) General. (1) Tolerances are established for combined residues of emamectin (a mixture of a minimum of 90% 4′-epi-methylamino-4′-deoxyavermectin B1a and maximum...

Research on disposal of copper(II)-containing wastewater by secondary strontium residue

NASA Astrophysics Data System (ADS)

Qing, Duowen; Xu, Longjun; Cui, Caixi

2018-01-01

Secondary strontium residue (SSR) was used as absorbent to remove Cu2+ in solution and the effects of experimental conditions on absorption of Cu2+ were investigated. The results showed that the absorption process reached balance in around 40 min. The absorption capacity achieved the maximum when PH value reached 6, and the maximum adsorption of Cu2+-containing wastewater by secondary strontium residue was 5.46 mg/g. Removal ratio of Cu2+ was in relation to initial concentration of Cu2+ in solution. Adsorptive process tallied with Langmuir Isothermal adsorption model.

Global Harmonization of Maximum Residue Limits for Pesticides.

PubMed

Ambrus, Árpád; Yang, Yong Zhen

2016-01-13

International trade plays an important role in national economics. The Codex Alimentarius Commission develops harmonized international food standards, guidelines, and codes of practice to protect the health of consumers and to ensure fair practices in the food trade. The Codex maximum residue limits (MRLs) elaborated by the Codex Committee on Pesticide Residues are based on the recommendations of the FAO/WHO Joint Meeting on Pesticides (JMPR). The basic principles applied currently by the JMPR for the evaluation of experimental data and related information are described together with some of the areas in which further developments are needed.

Residual toxicity of Cypermethrin in the larvae of coconut pest Oryctes rhinoceros (Coleoptera: Scarabaeidae).

PubMed

Venkatarajappa, P

2001-01-01

The toxic effect of Cypermethrin 10 EC (0.125, 0.25 and 0.5%) was estimated in the bodywall and digestive system of the larvae of Oryctes rhinoceros by HPLC after exposing them to different concentrations (0.125, 0.25 and 0.5%). Among the various concentrations used maximum residues were detected in bodywall (0.25%), whereas at higher concentration (0.5%) the residue detected was minimum. The treatment of Cypermethrin was found to be highly toxic upto 12 h of treatment, after which it declined reaching the minimum by 24 h. The residue of Cypermethrin could not be detected in digestive system. The experiments indicate the pesticide get concentrated in the bodywall to a maximum extent.

21 CFR 178.3530 - Isoparaffinic petroleum hydrocarbons, synthetic.

Code of Federal Regulations, 2014 CFR

2014-04-01

... millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residue 0.002 gram per 100 milliliters maximum. Synthetic isoparaffinic petroleum hydrocarbons containing... from the American Society for Testing Materials, 100 Barr Harbor Dr., West Conshohocken, Philadelphia...

The effect of motorcycle helmet fit on estimating head impact kinematics from residual liner crush.

PubMed

Bonin, Stephanie J; Gardiner, John C; Onar-Thomas, Arzu; Asfour, Shihab S; Siegmund, Gunter P

2017-09-01

Proper helmet fit is important for optimizing head protection during an impact, yet many motorcyclists wear helmets that do not properly fit their heads. The goals of this study are i) to quantify how a mismatch in headform size and motorcycle helmet size affects headform peak acceleration and head injury criteria (HIC), and ii) to determine if peak acceleration, HIC, and impact speed can be estimated from the foam liner's maximum residual crush depth or residual crush volume. Shorty-style helmets (4 sizes of a single model) were tested on instrumented headforms (4 sizes) during linear impacts between 2.0 and 10.5m/s to the forehead region. Helmets were CT scanned to quantify residual crush depth and volume. Separate linear regression models were used to quantify how the response variables (peak acceleration (g), HIC, and impact speed (m/s)) were related to the predictor variables (maximum crush depth (mm), crush volume (cm 3 ), and the difference in circumference between the helmet and headform (cm)). Overall, we found that increasingly oversized helmets reduced peak headform acceleration and HIC for a given impact speed for maximum residual crush depths less than 7.9mm and residual crush volume less than 40cm 3 . Below these levels of residual crush, we found that peak headform acceleration, HIC, and impact speed can be estimated from a helmet's residual crush. Above these crush thresholds, large variations in headform kinematics are present, possibly related to densification of the foam liner during the impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

21 CFR 178.3530 - Isoparaffinic petroleum hydrocarbons, synthetic.

Code of Federal Regulations, 2013 CFR

2013-04-01

... absorbance: 260-319 millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residue 0.002 gram per 100 milliliters maximum. Synthetic isoparaffinic petroleum.... Copies may be obtained from the American Society for Testing Materials, 100 Barr Harbor Dr., West...

21 CFR 178.3530 - Isoparaffinic petroleum hydrocarbons, synthetic.

Code of Federal Regulations, 2012 CFR

2012-04-01

... absorbance: 260-319 millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residue 0.002 gram per 100 milliliters maximum. Synthetic isoparaffinic petroleum.... Copies may be obtained from the American Society for Testing Materials, 100 Barr Harbor Dr., West...

Determination of imidocarb residues in bovine and ovine liver and milk by immunobiosensor.

PubMed

Traynor, I M; Thompson, C S; Armstrong, L; Fodey, T; Danaher, M; Jordan, K; Kennedy, D G; Crooks, S R H

2013-01-01

Imidocarb (IMD) is a veterinary drug that has been used for more than 30 years to treat and prevent parasitic diseases. Pharmacokinetic studies have shown that substantial levels of IMD residues are retained in the edible tissues and milk of cattle and sheep for up to 6 months after administration. This has led to concern regarding the potential adverse effects posed through human consumption of edible tissue or milk from treated animals if the recommended withdrawal periods for the drug are not properly implemented. While MRLs have been established by the European Union, it is important that analytical methods are available to monitor food samples for potentially violative levels of IMD residues. A qualitative biosensor-based immunoassay was developed to allow the detection of IMD at less than the European Union MRLs of 50 μg kg(-1) for milk and 2 mg kg(-1) for bovine and ovine liver. Validation of the developed methods provided a detection capability of <25 μg kg(-1) in milk and <0.75 mg kg(-1) in liver. A comparison study was undertaken, with IMD incurred milk and ovine liver samples analysed by the newly developed procedures and results compared with those obtained by LC-MS/MS. The newly developed screening method was applied to both incurred milk and liver samples. This faster, cheaper and reliable screening method has potential use in sample analysis to ensure compliance with legislative requirements.

Occurrence and Health Risk of Patulin and Pyrethroids in Fruit Juices Consumed in Bangkok, Thailand.

PubMed

Poapolathep, Saranya; Tanhan, Phanwimol; Piasai, Onuma; Imsilp, Kanjana; Hajslova, Jana; Giorgi, Mario; Kumagai, Susumu; Poapolathep, Amnart

2017-09-01

The mycotoxin patulin (PAT) is well known as a natural contaminant of apple- and other fruit-based products. Pesticides are a group of chemicals abundantly used in agriculture to maximize productivity by protecting crops from pests and weeds. Because of their harmful health effects, PAT and pesticides are strictly monitored. The current study was undertaken to investigate the significance of PAT and pyrethroid insecticide contamination in a variety of fruit juices in Bangkok. To do this, a total of 200 fruit juice samples, consisting of 40 samples each of apple, apricot, peach, pineapple, and grape juice, were collected from supermarkets in Bangkok, Thailand. PAT contamination in a variety of fruit juices was detected using validated liquid chromatography-tandem mass spectrometry, and pyrethroid insecticides (cypermethrin, cyfluthrin, and flumethrin) were analyzed using a gas chromatography equipped with micro-electron capture detector. The survey found that PAT concentrations were lower than the maximum residue limit established by European Union. The results of the present study suggest that the risk of exposure to harmful levels of PAT, cypermethrin, cyfluthrin, and flumethrin in fruit juices is very low in urban areas of Thailand.

The simultaneous death of seven people due to the detonation of an antipersonnel landmine at the land borders of the European Union during peacetime.

PubMed

Pavlidis, Pavlos; Karakasi, Valeria

2015-01-01

This incident concerns the simultaneous death of seven people as a result of the accidental triggering of an antipersonnel landmine during peacetime. The victims were illegal migrants who attempted to cross the Greek-Turkish border zone and accidentally entered a demarcated minefield. This incident is presented because of its rarity and highlights the devastating consequences of the residual mines on the European Union eastern frontiers in peacetime. It also showcases the difficulties and risks that arise during the identification process in illegal migration issues. The victims' positions at the moment of explosion are indicated by the detailed forensic examination and comparison of the injuries' anatomical dispersion and their severity.

[Scientific basis in the setting of residue limits for veterinary drugs in food of animal origin taking into account the presence of their metabolites].

PubMed

Mitsumori, K

1993-01-01

Maximum residue level (MRL) for veterinary drugs in food of animal origin has been proposed by FAO/WHO, as a new evaluation procedure taking into account the presence of metabolites for the regulation of veterinary drug residues. The MRL is the maximum concentration of residue resulting from the use of a veterinary drug that is recommended to be legally permitted as acceptable in a food. It is established from the Acceptable Daily Intake (ADI) obtained from the data of toxicological studies, the residue concentration of the drug when used according to good practice in the use of veterinary drugs, and the lowest level consistent with the practical analytical methods available for routine residue analysis. Among the veterinary drugs, some chemicals contain a large amount of bound residues that are neither extractable from tissues by the analytical method identical with that used in parent chemicals. Especially, the bioavailable residues which are probably absorbed when the food is ingested are of great toxicological concern. In this case, the FAO/WHO recommends that the MRL can be established after the calculation of daily intake of residues of toxicological concern by the addition of both the extractable and bioavailable bound residues.

Evaluation of a microbiological indicator test for antibiotic detection in ewe and goat milk.

PubMed

Comunian, R; Paba, A; Dupré, I; Daga, E S; Scintu, M F

2010-12-01

Antibiotics are widely used for therapeutic and prophylactic purposes in dairy animals. The presence of residual antibiotics in milk could cause potentially serious problems in human health and have technological implication in the manufacturing of dairy products. The aim of this study was to evaluate Delvotest Accelerator (DSM Food Specialties, Delft, the Netherlands), a new system for a fully automated microbial test to detect antibiotic residues in ewe and goat milk. Forty-three samples of raw, whole, refrigerated bulk-tank milk samples (22 of ewe milk and 21 of goat milk) were analyzed during the whole lactation period. Four concentrations of 4 antibiotics were diluted in milk: penicillin G at 1, 2, 3, and 4 μg/L; sulfadiazine at 25, 50, 100, and 200 μg/L; tetracycline at 50, 100, 200, and 400 μg/L; and gentamicin at 25, 50, 100, and 200 μg/L. The detection limit of the Delvotest Accelerator was calculated as the range of antibiotic concentrations within which 95% of positive result lie. The range of detection limit of penicillin G and sulfadiazine was easily detected by Delvotest Accelerator at or below the European Union maximum residue limits, both for ewe and goat milk samples. In contrast, the system showed a lower ability to detect tetracycline and gentamicin both for ewe and goat milk samples. Very low percentages of false-positive outcomes were obtained. Lactation phase did not seem to be a crucial factor affecting the ability of the Delvotest Accelerator to detect spiked milk samples. A higher detection ability was observed for goat milk samples compared with ewe milk samples. A negative correlation between the percentage of positive milk samples detected and milk fat, protein, and lactose contents was observed for gentamicin only. Copyright © 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

6-Iso-chlortetracycline or keto form of chlortetracycline? Need for clarification for relevant monitoring of chlortetracycline residues in food.

PubMed

Gaugain, Murielle; Gautier, Sophie; Bourcier, Sophie; Jacques, Anne-Marie; Laurentie, Michel; Abjean, Jean-Pierre; Hurtaud-Pessel, Dominique; Verdon, Eric

2015-01-01

Chlortetracycline (CTC) is a broad-spectrum antibiotic used in veterinary medicine for pulmonary or digestive infections and having a regulatory maximum residue limit (MRL) necessitating an official analytical control method. The purpose of this study was to clarify the identification of different forms of CTC observed in standard solution, in spiked muscle samples and in naturally incurred muscle samples of pigs analysed by LC-MS/MS and to demonstrate the in vivo formation of 6-iso-chlortetracycline and 4-epi-6-iso-CTC as a metabolite of CTC and 4-epi-CTC in muscle. The six following forms were identified, all being isobaric with a protonated molecule at m/z 479 (precursor ion): the keto-enol forms of CTC and the keto-enol forms of 4-epi-chlortetracycline (4-epi-CTC), 6-iso-chlortetracycline (6-iso-CTC) and 4-epi-6-iso-chlortetracycline (4-epi-6-iso-CTC). The 6-iso-CTC and 4-epi-6-iso-CTC were observed only in incurred pig samples so were identified for the first time as metabolites of CTC and 4-epi-CTC. Identification of the different forms was obtained by comparing incurred muscle samples with standard solutions and with spiked samples. Then the differences between the features of the chromatograms obtained by LC-TQ-MS and the fragmentation study of the different forms of CTC obtained by LC-Q-TOF-MS helped us to support this identification. The extraction steps and the LC-MS/MS conditions developed to analyse muscle tissue samples are described. This clarification concerning the rigorous identification of chromatographic peaks allowed us to evaluate the relevance of our monitoring method with regard to the regulations in place in the European Union and could be of help to laboratories involved in official control of antibiotic residues in food of animal origin. Additional results are also presented highlighting the transformation of the CTC when prepared in a mixture with other antibiotics.

Pesticide residues in berries harvested from South-Eastern Poland (2009-2011).

PubMed

Matyaszek, Aneta; Szpyrka, Ewa; Podbielska, Magdalena; Słowik-Borowiec, Magdalena; Kurdziel, Anna

2013-01-01

Poland is a leading grower/producer of berries in Europe that are either eaten raw or processed. As well as berries this includes fruit such as grapes, strawberries and other small fruits. Testing for the presence of active substances in Plant Protection Products, (PPP), in such fruit is however important, as part of measures taken to minimise human intake. To determine the incidence of pesticide residues in berries harvested from South-Eastern Poland in 2009-2011. . Chromatographic separation followed by analytical detection was performed on 250 samples of various test fruits using an accredited methodology: GC/ECD/NPD, together with spectrophotometric detection wherever necessary, according to PN-EN ISO/IEC 17025. As part of previous monitoring, 126 active substances were identified in 2009, 132 in 2010 and 153 in 2011; levels were compared to Maximum Residue Limits (MRLs). RESULTS;. Analyses showed that 46.4% of samples contained PPPs of which 4% exceeded the MRL. The most were found in raspberries, (58.8% of all tested), followed by 58.3% redcurrants, and gooseberries as well as 50% grapes. The most frequently found active substances of PPPs were pyrimethanil (15.6%), dithiocarbamates (12.4%), procymidone (8%), cyprodinil (5.6%) and difenoconazole (5.2%). The highest MRL exceedances were found in blackcurrants. Testing also revealed many examples of pesticides not recommended for the protection of specific crops: propiconazole in gooseberries, cyprodinil, flusilazole, iprodione, pyrimethanil in blackcurrants and folpet and captan in raspberries. Furthermore, active substances whose use in PPPs have been forbidden since 2008 were also detected, ie. endosulfan in blackcurrants and strawberries, fenitrothion in black and red currants as well as procymidone in raspberries, blackcurrants and strawberries. These data are consistent to those obtained from the whole of Poland and the European Union (EU). Most pesticides were present in raspberries, redcurrants, gooseberries and grapes of which fungicides were the most frequently detected. These results are in keeping with other similar studies.

Tylosin depletion from edible pig tissues.

PubMed

Prats, C; El Korchi, G; Francesch, R; Arboix, M; Pérez, B

2002-12-01

The depletion of tylosin from edible pig tissues was studied following 5 days of intramuscular (i.m.) administration of 10 mg/kg of tylosin to 16 crossbreed pigs. Animals were slaughtered at intervals after treatment and samples of muscle, kidney, liver, skin+fat, and injection site were collected and analysed by high-performance liquid chromatography (HPLC). Seven days after the completion of treatment, the concentration of tylosin in kidney, skin+fat, and at the injection site was higher than the European Union maximal residue limit (MRL) of 100 microg/kg. Tylosin residues in all tissues were below the quantification limit (50 microg/kg) at 10 and 14 days post-treatment.

Anomaly Detection in Moving-Camera Video Sequences Using Principal Subspace Analysis

DOE PAGES

Thomaz, Lucas A.; Jardim, Eric; da Silva, Allan F.; ...

2017-10-16

This study presents a family of algorithms based on sparse decompositions that detect anomalies in video sequences obtained from slow moving cameras. These algorithms start by computing the union of subspaces that best represents all the frames from a reference (anomaly free) video as a low-rank projection plus a sparse residue. Then, they perform a low-rank representation of a target (possibly anomalous) video by taking advantage of both the union of subspaces and the sparse residue computed from the reference video. Such algorithms provide good detection results while at the same time obviating the need for previous video synchronization. However,more » this is obtained at the cost of a large computational complexity, which hinders their applicability. Another contribution of this paper approaches this problem by using intrinsic properties of the obtained data representation in order to restrict the search space to the most relevant subspaces, providing computational complexity gains of up to two orders of magnitude. The developed algorithms are shown to cope well with videos acquired in challenging scenarios, as verified by the analysis of 59 videos from the VDAO database that comprises videos with abandoned objects in a cluttered industrial scenario.« less

Anomaly Detection in Moving-Camera Video Sequences Using Principal Subspace Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomaz, Lucas A.; Jardim, Eric; da Silva, Allan F.

This study presents a family of algorithms based on sparse decompositions that detect anomalies in video sequences obtained from slow moving cameras. These algorithms start by computing the union of subspaces that best represents all the frames from a reference (anomaly free) video as a low-rank projection plus a sparse residue. Then, they perform a low-rank representation of a target (possibly anomalous) video by taking advantage of both the union of subspaces and the sparse residue computed from the reference video. Such algorithms provide good detection results while at the same time obviating the need for previous video synchronization. However,more » this is obtained at the cost of a large computational complexity, which hinders their applicability. Another contribution of this paper approaches this problem by using intrinsic properties of the obtained data representation in order to restrict the search space to the most relevant subspaces, providing computational complexity gains of up to two orders of magnitude. The developed algorithms are shown to cope well with videos acquired in challenging scenarios, as verified by the analysis of 59 videos from the VDAO database that comprises videos with abandoned objects in a cluttered industrial scenario.« less

21 CFR 172.882 - Synthetic isoparaffinic petroleum hydrocarbons.

Code of Federal Regulations, 2013 CFR

2013-04-01

... absorbance: 260-319 millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residual: 0.002 gram per 100 milliliters maximum. Synthetic isoparaffinic petroleum... reference. Copies may be obtained from the American Society for Testing Materials, 100 Barr Harbor Dr., West...

21 CFR 172.882 - Synthetic isoparaffinic petroleum hydrocarbons.

Code of Federal Regulations, 2012 CFR

2012-04-01

... absorbance: 260-319 millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residual: 0.002 gram per 100 milliliters maximum. Synthetic isoparaffinic petroleum... reference. Copies may be obtained from the American Society for Testing Materials, 100 Barr Harbor Dr., West...

Evaluation of certain veterinary drug residues in food. Seventy-eighth report of the Joint FAO/WHO Expert Committee on Food Additives.

PubMed

2014-01-01

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of residues of certain veterinary drugs in food and to recommend maximum levels for such residues of food. The first part of the report considers general principles regarding the evaluation of residues of veterinary drugs within the terms of reference of the Joint FAO/WHO Expert Committee on Food Additives (JECFA), including extrapolation of maximum residue limits (MRLs) to minor species, MRLs for veterinary drug residues in honey, MRLs relating to fish and fish species, dietary exposure assessment methodologies, the decision-tree approach to the evaluation of residues of veterinary drugs and guidance for JECFA experts. Summaries follow of the Committee's evaluations of toxicology and residue data on a variety of veterinary drugs: two anthelminthic agents (derquantel, monepantel), three antiparasitic agents (emanectin benzoate, ivermectin, lasalocid sodium), one antibacterial, antifungal and anthelminthic agent (gentian violet), a production aid (recombinant bovine somatotropins) and an adrenoceptor agonist and growth promoter (zilpaterol hydorchloride). Annexed to the report is a summary of the Committee's recommendations on these drugs, including acceptable daily intakes (ADIs)) and proposed MRLs.

A gold immunochromatographic assay for the rapid and simultaneous detection of fifteen β-lactams

NASA Astrophysics Data System (ADS)

Chen, Yanni; Wang, Yongwei; Liu, Liqiang; Wu, Xiaoling; Xu, Liguang; Kuang, Hua; Li, Aike; Xu, Chuanlai

2015-10-01

A novel gold immunochromatographic assay (GICA) based on anti-β-lactam receptors was innovatively developed that successfully allowed rapid and simultaneous detection of fifteen β-lactams in milk samples in 5-10 minutes. By replacing the antibodies used in traditional GICA with anti-β-lactam receptors, the difficulty in producing broad specific antibodies against β-lactams was overcome. Conjugates of ampicillin with BSA and goat anti-mouse immunoglobulin (IgG) were immobilized onto the test and control lines on the nitrocellulose membrane, respectively. Since goat anti-mouse IgG does not combine with receptors, negative serum from mice labelled with gold nanoparticles (GNP) was mixed with GNP-labelled receptors. Results were obtained within 20 min using a paper-based sensor. The utility of the assay was confirmed by the analysis of milk samples. The limits of detection (LOD) for amoxicillin, ampicillin, penicillin G, penicillin V, cloxacillin, dicloxacillin, nafcillin, oxacillin, cefaclor, ceftezole, cefotaxime, ceftiofur, cefoperazone, cefathiamidine, and cefepime were 0.25, 0.5, 0.5, 0.5, 1, 5, 5, 10, 25, 10, 100, 10, 5, 5, and 2 ng mL-1, respectively, which satisfies the maximum residue limits (MRL) set by the European Union (EU). In conclusion, our newly developed GICA-based anti-β-lactam receptor assay provides a rapid and effective method for one-site detection of multiple β-lactams in milk samples.A novel gold immunochromatographic assay (GICA) based on anti-β-lactam receptors was innovatively developed that successfully allowed rapid and simultaneous detection of fifteen β-lactams in milk samples in 5-10 minutes. By replacing the antibodies used in traditional GICA with anti-β-lactam receptors, the difficulty in producing broad specific antibodies against β-lactams was overcome. Conjugates of ampicillin with BSA and goat anti-mouse immunoglobulin (IgG) were immobilized onto the test and control lines on the nitrocellulose membrane, respectively. Since goat anti-mouse IgG does not combine with receptors, negative serum from mice labelled with gold nanoparticles (GNP) was mixed with GNP-labelled receptors. Results were obtained within 20 min using a paper-based sensor. The utility of the assay was confirmed by the analysis of milk samples. The limits of detection (LOD) for amoxicillin, ampicillin, penicillin G, penicillin V, cloxacillin, dicloxacillin, nafcillin, oxacillin, cefaclor, ceftezole, cefotaxime, ceftiofur, cefoperazone, cefathiamidine, and cefepime were 0.25, 0.5, 0.5, 0.5, 1, 5, 5, 10, 25, 10, 100, 10, 5, 5, and 2 ng mL-1, respectively, which satisfies the maximum residue limits (MRL) set by the European Union (EU). In conclusion, our newly developed GICA-based anti-β-lactam receptor assay provides a rapid and effective method for one-site detection of multiple β-lactams in milk samples. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04987c

Assessment of collection schemes for packaging and other recyclable waste in European Union-28 Member States and capital cities.

PubMed

Seyring, Nicole; Dollhofer, Marie; Weißenbacher, Jakob; Bakas, Ioannis; McKinnon, David

2016-09-01

The Waste Framework Directive obliged European Union Member States to set up separate collection systems to promote high quality recycling for at least paper, metal, plastic and glass by 2015. As implementation of the requirement varies across European Union Member States, the European Commission contracted BiPRO GmbH/Copenhagen Resource Institute to assess the separate collection schemes in the 28 European Union Member States, focusing on capital cities and on metal, plastic, glass (with packaging as the main source), paper/cardboard and bio-waste. The study includes an assessment of the legal framework for, and the practical implementation of, collection systems in the European Union-28 Member States and an in depth-analysis of systems applied in all capital cities. It covers collection systems that collect one or more of the five waste streams separately from residual waste/mixed municipal waste at source (including strict separation, co-mingled systems, door-to-door, bring-point collection and civic amenity sites). A scoreboard including 13 indicators is elaborated in order to measure the performance of the systems with the capture rates as key indicators to identify best performers. Best performance are by the cities of Ljubljana, Helsinki and Tallinn, leading to the key conclusion that door-to-door collection, at least for paper and bio-waste, and the implementation of pay-as-you-throw schemes results in high capture and thus high recycling rates of packaging and other municipal waste. © The Author(s) 2016.

Evaluation of available data on the geohydrology, soil chemistry, and ground-water chemistry of Gas Works Park and surrounding region, Seattle, Washington

USGS Publications Warehouse

Sabol, M.A.; Turney, G.L.; Ryals, G.N.

1988-01-01

Gas Works Park, in Seattle, Washington, is located at the site of an abandon gasification plant on Lake Union. Wastes deposited during 50 years of plant operations (1906-1956) have extended the shore line 100 ft and left the park soil contaminated with a number of hazardous material. Soil contaminants include polynuclear aromatic hydrocarbons (PAHs), polychlorinated biphenyls, pesticides, volatile organic compounds, cyanide, and metals. PAHs and metals have been detected in Lake Union sediments. Maximum total PAH concentrations exceeded 100 million micrograms/kilogram in some places in the soils of the park at 6-inch depths and in some lake sediments. Other contaminants present are much lower in concentrations. The park is on glacial drift overlain by gasification waste materials and clean fill. Waste materials include sand and gravels, mixed with lampblack, oil, bricks, and other industrial wastes. Groundwater flows through the soils and waste toward Lake Union. Vertical groundwater movement is uncertain, but is assumed to be upward near Lake Union. Concentrations of most soil contaminants are probably low in the groundwater and in Lake Union due to the low solubilities and high sorptive characteristics of these contaminants. However, no water quality data are available to confirm this premise. (USGS)

Statistical analysis of the mesospheric inversion layers over two symmetrical tropical sites: Réunion (20.8° S, 55.5° E) and Mauna Loa (19.5° N, 155.6° W)

NASA Astrophysics Data System (ADS)

Bègue, Nelson; Mbatha, Nkanyiso; Bencherif, Hassan; Tato Loua, René; Sivakumar, Venkataraman; Leblanc, Thierry

2017-11-01

In this investigation a statistical analysis of the characteristics of mesospheric inversion layers (MILs) over tropical regions is presented. This study involves the analysis of 16 years of lidar observations recorded at Réunion (20.8° S, 55.5° E) and 21 years of lidar observations recorded at Mauna Loa (19.5° N, 155.6° W) together with SABER observations at these two locations. MILs appear in 10 and 9.3 % of the observed temperature profiles recorded by Rayleigh lidar at Réunion and Mauna Loa, respectively. The parameters defining MILs show a semi-annual cycle over the two selected sites with maxima occurring near the equinoxes and minima occurring during the solstices. Over both sites, the maximum mean amplitude is observed in April and October, and this corresponds to a value greater than 35 K. According to lidar observations, the maximum and minimum mean of the base height ranged from 79 to 80.5 km and from 76 to 77.5 km, respectively. The MILs at Réunion appear on average ˜ 1 km thinner and ˜ 1 km lower, with an amplitude of ˜ 2 K higher than Mauna Loa. Generally, the statistical results for these two tropical locations as presented in this investigation are in fairly good agreement with previous studies. When compared to lidar measurements, on average SABER observations show MILs with greater amplitude, thickness and base altitudes of 4 K, 0.75 and 1.1 km, respectively. Taking into account the temperature error by SABER in the mesosphere, it can therefore be concluded that the measurements obtained from lidar and SABER observations are in significant agreement. The frequency spectrum analysis based on the lidar profiles and the 60-day averaged profile from SABER confirms the presence of the semi-annual oscillation where the magnitude maximum is found to coincide with the height range of the temperature inversion zone. This connection between increases in the semi-annual component close to the inversion zone is in agreement with most previously reported studies over tropics based on satellite observations. Results presented in this study confirm through the use of the ground-based Rayleigh lidar at Réunion and Mauna Loa that the semi-annual oscillation contributes to the formation of MILs over the tropical region.

Hadean silicate differentiation preserved by anomalous 142Nd/144Nd ratios in the Réunion hotspot source

NASA Astrophysics Data System (ADS)

Peters, Bradley J.; Carlson, Richard W.; Day, James M. D.; Horan, Mary F.

2018-03-01

Active volcanic hotspots can tap into domains in Earth’s deep interior that were formed more than two billion years ago. High-precision data on variability in tungsten isotopes have shown that some of these domains resulted from differentiation events that occurred within the first fifty million years of Earth history. However, it has not proved easy to resolve analogous variability in neodymium isotope compositions that would track regions of Earth’s interior whose composition was established by events occurring within roughly the first five hundred million years of Earth history. Here we report 142Nd/144Nd ratios for Réunion Island igneous rocks, some of which are resolvably either higher or lower than the ratios in modern upper-mantle domains. We also find that Réunion 142Nd/144Nd ratios correlate with helium-isotope ratios (3He/4He), suggesting parallel behaviour of these isotopic systems during very early silicate differentiation, perhaps as early as 4.39 billion years ago. The range of 142Nd/144Nd ratios in Réunion basalts is inconsistent with a single-stage differentiation process, and instead requires mixing of a conjugate melt and residue formed in at least one melting event during the Hadean eon, 4.56 billion to 4 billion years ago. Efficient post-Hadean mixing nearly erased the ancient, anomalous 142Nd/144Nd signatures, and produced the relatively homogeneous 143Nd/144Nd composition that is characteristic of Réunion basalts. Our results show that Réunion magmas tap into a particularly ancient, primitive source compared with other volcanic hotspots, offering insight into the formation and preservation of ancient heterogeneities in Earth’s interior.

34 CFR 461.12 - What must the State plan contain?

Code of Federal Regulations, 2011 CFR

2011-07-01

... system, businesses, labor unions, libraries, institutions of higher education, public health authorities... Higher Education Act of 1965, and the Domestic Volunteer Service Act, to ensure maximum use of funds and... Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND...

Determination of the Ability to Measure Traces of Water in Dehydrated Residues of Waste Water by IR Diffuse Reflectance Spectra

NASA Astrophysics Data System (ADS)

Pratsenka, S. V.; Voropai, E. S.; Belkin, V. G.

2018-01-01

Rapid measurement of the moisture content of dehydrated residues is a critical problem, the solution of which will increase the efficiency of treatment facilities and optimize the process of applying flocculants. The ability to determine the moisture content of dehydrated residues using a meter operating on the IR reflectance principle was confirmed experimentally. The most suitable interference filters were selected based on an analysis of the obtained diffuse reflectance spectrum of the dehydrated residue in the range 1.0-2.7 μm. Calibration curves were constructed and compared for each filter set. A measuring filter with a transmittance maximum at 1.19 μm and a reference filter with a maximum at 1.3 μm gave the best agreement with the laboratory measurements.

[Regulation of food supplements in the European Union and its member states. Part I].

PubMed

Petrenko, A S; Ponomareva, M N; Sukhanov, B P

2014-01-01

The article discusses aspects of the regional (the European Union) and national (European countries) regulation of food supplements. The definition of the supplement category is given. The contemporary issues of nutrition in developed countries are discussed, and the essential role of food supplements in the diet is emphasized. In particular, the use of vitamins, minerals, botanicals and their chemical constituents in food supplements as well as the issue of setting maximum daily limits are discussed. The positive lists of vitamins, minerals and their chemical modifications are presented. The paper also outlines aspects of supplement safety, requirements for their labelling and pre-market notification procedure.

Effect of ferrous sulfate and nitrohumic acid neutralization on the leaching of metals from a combined bauxite residue.

PubMed

Ren, Jie; Liu, Jidong; Chen, Juan; Liu, Xiaolian; Li, Fasheng; Du, Ping

2017-04-01

Bauxite residue neutralization is intended to open opportunities for revegetation and reuse of the residue. Ferrous sulfate (FS) and nitrohumic acid (NA) were two kinds of materials studied for pH reduction of the residue from 10.6 to 8.3 and 8.1, respectively. The effects of FS and NA on the leaching of metals from a combined bauxite residue were investigated by using sequential and multiple extraction procedures. Neutralization with FS and NA restricted the leaching of Al, V, and Pb from the residue but promoted the leaching of Fe, Cu, Mn, and Ni, consistent with the changes in the potentially mobile fractions. With the exceptions of Pb and Ni, leaching of metals increased during a 10-day extraction period. However, the maximum leaching of Al, V, Pb, Fe, Cu, Mn, and Ni from neutralized bauxite residue were 0.46 mg/L, 59.3, 12.9, 167, 95.3, 15.5, and 14.5 μg/L, respectively, which were under the corresponding limits in the National Standard (GB/T 14848-93). Although it is necessary to consider the continued leaching of metals during neutralization, both maximum and accumulation leaching concentrations of metals from a combined bauxite residue were too low to pose a potential environmental risk.

Organochlorine insecticide residues in the free-tailed bat (Tadarida brasiliensis) at Bracken Cave, Texas

USGS Publications Warehouse

Clark, D.R.; Martin, C.O.; Swineford, D.M.

1975-01-01

Fifty-nine free-tailed bats (Tadarida brasiliensis mexicana ) were collected at Bracken Cave, Texas, and analyzed for organochlorine insecticides and polychlorinated biphenyls (PCBs). Residues of DDE in the brain were greater in 12 young collected from the floor than in 15 young taken from the ceiling, but food deprivation, not higher residues in the brain, apparently caused young to fall....Among 18 pregnant females, residues of DDE and DDT were highest in yearlings. The first lactation by yearlings caused their residue loads to drop sharply. Thereafter, increasing age was accompanied by increasing residues but amounts generally did not exceed those in yearlings.....Residue levels in embryos were a function both of levels in the female parent and degree of embryonic development. Residues accumulated rapidly in nursing young, and lactating females may excrete from 1.3 to 16.2 (mean = 4.3) micrograms of DDE in milk per day. Maximum individual residue loads may be attained toward the end of nursing, and mobilization of these residues during southward migration may subject Bracken Cave free-tails to maximum lifetime residues in the brain....Comparison of our data with residue data for the free-tail population at Eagle Creek Cave (Arizona) in 1970 produced the following conclusions: ( 1) residues of DDE appeared similar in pregnant females, embryos, lactating females, and fallen young for the two populations; (2) residues of DDT and dieldrin appeared greater in pregnant females at Bracken Cave; (3) DDE and DDT occurred at greater levels in guano samples from Bracken Cave. On this basis, the population decline observed at Eagle Creek Cave between 1963 and 1969 does not appear to be related to the residues observed in the 1970 samples taken from that cave.

Analysis of organo-chlorine pesticides residue in raw coffee with a modified "quick easy cheap effective rugged and safe" extraction/clean up procedure for reducing the impact of caffeine on the gas chromatography-mass spectrometry measurement.

PubMed

Bresin, Bruno; Piol, Maria; Fabbro, Denis; Mancini, Maria Antonietta; Casetta, Bruno; Del Bianco, Clorinda

2015-01-09

The control of pesticide residues on raw coffee is a task of great importance due to high consumption of this beverage in Italy and in many other countries. High caffeine content can hamper extraction and measurement of any pesticide residue. A tandem extraction protocol has been devised by exploiting the quick easy cheap effective rugged and safe (QuEChERS) scheme for extraction, coupled to a dispersive liquid-liquid micro-extraction (DLLME) in order to drastically reduce caffeine content in the final extract. Gas chromatography-mass spectrometry (GC-MS) has been used for quantification of organo-chlorine pesticides in single ion monitoring (SIM) mode. Method has been validated and performances meet the criteria prescribed by European Union regulations. Copyright © 2014 Elsevier B.V. All rights reserved.

Health hazard evaluation report HETA 83-248-1515, Arco Philadelphia refinery, Philadelphia, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, F.A.; Parrish, G.

1984-10-01

A bulk sample of fractionator residue was analyzed for polynuclear aromatic (PNA) compounds at the catalytic cracking unit of ARCO Philadelphia Refinery (SIC-2911), Philadelphia, Pennsylvania in May, 1983. The study was requested by the Atlantic Independent Union to determine if skin rashes and skin irritation occurring among refinery workers were caused by PNA in the fractionators. The authors conclude that a health hazard from exposure to chemicals at the cracking unit may exist. No specific chemical agent can be identified. Dust from the catalyst and oily residues that could contaminate workers shoes and clothing may have contributed to some ofmore » the dermatitis cases. Recommendations include laundering workers coveralls by dry cleaning to insure the removal of oily residues, providing workers with oil resistant or oil proof work boots, and repairing the ventilator in the sample preparation room adjacent to the block house.« less

12 CFR 705.2 - Purpose of the program.

Code of Federal Regulations, 2010 CFR

2010-01-01

... financial and related services to residents in their communities; and (2) Stimulating economic activities in... opportunities for low-income residents, and other community growth efforts. (b) The policy of NCUA is to revolve loan funds to qualifying credit unions as often as practical in order to gain maximum economic impact...

21 CFR 172.882 - Synthetic isoparaffinic petroleum hydrocarbons.

Code of Federal Regulations, 2014 CFR

2014-04-01

... American Society for Testing Materials, 100 Barr Harbor Dr., West Conshohocken, Philadelphia, PA 19428-2959.../code_of_federal_regulations/ibr_locations.html. Ultraviolet absorbance: 260-319 millimicrons—1.5 maximum. 320-329 millimicrons—0.08 maximum. 330-350 millimicrons—0.05 maximum. Nonvolatile residual: 0.002...

Determining crop residue type and class using satellite acquired data. M.S. Thesis Progress Report, Jun. 1990

NASA Technical Reports Server (NTRS)

Zhuang, Xin

1990-01-01

LANDSAT Thematic Mapper (TM) data for March 23, 1987 with accompanying ground truth data for the study area in Miami County, IN were used to determine crop residue type and class. Principle components and spectral ratioing transformations were applied to the LANDSAT TM data. One graphic information system (GIS) layer of land ownership was added to each original image as the eighth band of data in an attempt to improve classification. Maximum likelihood, minimum distance, and neural networks were used to classify the original, transformed, and GIS-enhanced remotely sensed data. Crop residues could be separated from one another and from bare soil and other biomass. Two types of crop residue and four classes were identified from each LANDSAT TM image. The maximum likelihood classifier performed the best classification for each original image without need of any transformation. The neural network classifier was able to improve the classification by incorporating a GIS-layer of land ownership as an eighth band of data. The maximum likelihood classifier was unable to consider this eighth band of data and thus, its results could not be improved by its consideration.

Development and validation of an HPLC method for the determination of ten sulfonamide residues in milk according to 2002/657/EC.

PubMed

Tolika, Evanthia P; Samanidou, Victoria F; Papadoyannis, Ioannis N

2011-07-01

A HPLC method with diode-array detection, at 265 nm, was developed and validated for the determination of ten sulfonamides (SAs): sulfadiazine (SDZ), sulfathiazine (STZ), sulfamethoxine (SMTH), sulfamethizole (SMZ), sulfamethoxypyridazine (SMPZ), sulfamonomethoxine (SMMX), sulfamethoxazole (SMXZ), sulfisoxazole (SIX), sulfadimethoxine (SDMX), and sulfaquinoxaline (SQX) in milk. A mixture of ethyl acetate, n-hexane, and isopropanol was used for the extraction of target analytes from milk. The mobile phase, a mixture of 0.1% v/v formic acid, CH(3) CN, and CH(3) OH was delivered to the analytical column under a gradient program. The procedure was validated according to the European Union regulation 2002/657/EC in terms of selectivity, stability, decision limit, detection capability, accuracy, and precision. Mean recoveries of sulfonamides from milk samples spiked at three concentration levels (0.5×MRL, 1×MRL, and 1.5×MRL) (MRL, maximum residue level) were 93.9-115.9% for SDZ, 97.8-102.9% for STZ, 94.6-107.0% for SMTH, 98.3-111.5% for SMZ, 95.3-108.4% for SMPZ, 97.9-106.0% for SMMX, 97.6-111.3% for SMXZ, 94.3-104.6% for SIX, 96.4-109.1% for SDMX, and 98.2-111.2% for SQX. All RSD values were lower than 8.8%. The decision limits CCa calculated by spiking 20 blank milk samples at MRL (100 μg/kg) ranged from 101.61 to 106.84 μg/kg, whereas the detection capability CCb ranged from 105.64 to 119.01 μg/kg. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Residues of organochlorine pesticides in surface water of a megacity in central China: seasonal-spatial distribution and fate in Wuhan.

PubMed

Cui, Lili; Wei, Liangfu; Wang, Jun

2017-01-01

Surface water quality closely correlating with human health suffered increasing organochlorine pesticide (OCP) pollution due to the intensive anthropogenic activities in megacities. In the present study, 112 water samples collected from 14 lakes and 11 drinking water source sites in Wuhan were detected for the residues of OCPs in November 2013 and July 2014, respectively. The ΣOCPs ranged from 5.61 to 13.62 ng L -1 in summer with the maximum value in Yezhi Lake and 3.18 to 7.73 ng L -1 in winter with the highest concentration in Yandong Lake. Except dichlorodiphenyltrichloroethanes (DDTs), OCP concentrations in summer were significantly higher than those in winter mostly due to the non-point source pollution including land runoff in summer. Source apportionment of hexachlorocyclohexanes (HCHs) and DDTs revealed the historical use of technical HCH and lindane and the new input of DDT, respectively. The spatial distribution of OCPs was not uniform in the surface water of Wuhan because of the significant influence of land development and fishery. The risk assessments showed the heptachlor, and heptachlor epoxide in most sampling sites exceeded the threshold set by the European Union, indicating the possible adverse effects for aquatic lives. Negligible non-carcinogenic risks for drinking and bathing as well as carcinogenic risks for bathing were found in the surface water. However, the total carcinogenic risks of all OCPs (∑Rs) caused by drinking in summer were higher than the safe level of 10 -7 in all sampling sites. It was implied that the surface water in Wuhan was not safe for directly drinking without effective purification.

Performance of blue-yellow screening test for antimicrobial detection in ovine milk.

PubMed

Linage, B; Gonzalo, C; Carriedo, J A; Asensio, J A; Blanco, M A; De La Fuente, L F; San Primitivo, F

2007-12-01

Drug residues in milk are important because of public health and industrial implications. The detection limits of 25 antimicrobial agents were determined by the blue-yellow screening method in ovine milk. For each drug, 8 concentrations were tested on 20 ovine milk samples from individual ewes in midlactation. Detection limits determined by means of logistic regression were below European Union maximum residue limits (EU-MRL) for penicillin G (3 to 4 microg/kg), ceftiofur (96 to 107 microg/kg), framycetin (720 to 781 microg/kg), neomycin (915 to 1,084 microg/kg), and tylosin (44 to 51 microg/kg). Detection limits for ampicillin (5 to 6 microg/kg), cloxacillin (33 to 42 microg/kg), cefoperazone (73 to 82 microg/kg), cefalexin (160 to 202 microg/kg), gentamycin (355 to 382 microg/kg), streptomycin (3,063 to 3,593 microg/kg), tilmicosin (109 to 131 microg/kg), erythromycin (444 to 522 microg/kg), spyramicin (1,106 to 1,346 microg/kg), sulfadimethoxine (101 to 119 microg/kg), sulfathiazole (122 to 151 microg/kg), sulfamethazine (309 to 328 microg/kg), sulfanilamide (1,750 to 2,674 microg/kg), tetracycline (233 to 257 microg/kg), oxytetracycline (398 to 501 microg/kg), doxycycline (323 to 419 microg/kg), chlortetracycline (3,331 to 3,989 microg/kg), danofloxacin (4.7 to 5.5 mg/kg), enrofloxacin (41 to 46 mg/kg), and flumequin (63 to 71 mg/kg) were higher than the EU-MRL. Although the blue-yellow method showed improved sensitivity compared with other tests studied in ovine milk, the performance of screening methods for detecting antimicrobial agents in milk of this species should be improved.

Multiresidue analysis of sulfonamides in meat by supramolecular solvent microextraction, liquid chromatography and fluorescence detection and method validation according to the 2002/657/EC decision.

PubMed

Costi, Esther María; Sicilia, María Dolores; Rubio, Soledad

2010-10-01

A multiresidue method was described for determining eight sulfonamides, SAs (sulfadiazine, sulfamerazine, sulfamethoxypyridazine, sulfachloropyridazine, sulfadoxine, sulfamethoxazole, sulfadimethoxine and sulfaquinoxaline) in animal muscle tissues (pork, chicken, turkey, lamb and beef) at concentrations below the maximum residue limit (100 μg kg(-1)) set by the European Commission. The method was based on the microextraction of SAs in 300-mg muscle samples with 1 mL of a supramolecular solvent made up of reverse micelles of decanoic acid (DeA) and posterior determination of SAs in the extract by LC/fluorescence detection, after in situ derivatization with fluorescamine. Recoveries were quantitative (98-109%) and matrix-independent, no concentration of the extracts was required, the microextraction took about 30 min and several samples could be simultaneously treated. Formation of multiple hydrogen bonds between the carboxylic groups of the solvent and the target SAs (hydrogen donor and acceptor sum between 9 and 11) were considered as the major forces driving microextraction. The method was validated according to the European Union regulation 2002/657/EC. Analytical performance in terms of linearity, selectivity, trueness, precision, stability of SAs, decision limit and detection capability were determined. Quantitation limits for the different SAs ranged between 12 μg kg(-1) and 44 μg kg(-1), they being nearly independent of matrix composition. Repeatability and reproducibility, expressed as relative standard deviation, were in the ranges 1.8-3.6% and 3.3-6.1%. The results of the validation process proved that the method is suitable for determining sulfonamide residues in surveillance programs. Copyright © 2010 Elsevier B.V. All rights reserved.

Evaluation of Methane from Sisal Leaf Residue and Palash Leaf Litter

NASA Astrophysics Data System (ADS)

Arisutha, S.; Baredar, P.; Deshpande, D. M.; Suresh, S.

2014-12-01

The aim of this study is to evaluate methane production from sisal leaf residue and palash leaf litter mixed with different bulky materials such as vegetable market waste, hostel kitchen waste and digested biogas slurry in a laboratory scale anaerobic reactor. The mixture was prepared with 1:1 proportion. Maximum methane content of 320 ml/day was observed in the case of sisal leaf residue mixed with vegetable market waste as the feed. Methane content was minimum (47 ml/day), when palash leaf litter was used as feed. This was due to the increased content of lignin and polyphenol in the feedstock which were of complex structure and did not get degraded directly by microorganisms. Sisal leaf residue mixtures also showed highest content of volatile fatty acids (VFAs) as compared to palash leaf litter mixtures. It was observed that VFA concentration in the digester first increased, reached maximum (when pH was minimum) and then decreased.

Isometric Mid-Thigh Pull Correlates With Strength, Sprint, and Agility Performance in Collegiate Rugby Union Players.

PubMed

Wang, Ran; Hoffman, Jay R; Tanigawa, Satoru; Miramonti, Amelia A; La Monica, Michael B; Beyer, Kyle S; Church, David D; Fukuda, David H; Stout, Jeffrey R

2016-11-01

Wang, R, Hoffman, JR, Tanigawa, S, Miramonti, AA, La Monica, MB, Beyer, KS, Church, DD, Fukuda, DH, and Stout, JR. Isometric mid-thigh pull correlates with strength, sprint, and agility performance in collegiate rugby union players. J Strength Cond Res 30(11): 3051-3056, 2016-The purpose of this investigation was to examine the relationships between isometric mid-thigh pull (IMTP) force and strength, sprint, and agility performance in collegiate rugby union players. Fifteen members of a champion-level university's club rugby union team (mean ± SD: 20.67 ± 1.23 years, 1.78 ± 0.06 m, and 86.51 ± 14.18 kg) participated in this investigation. One repetition maximum (1RM) squat, IMTP, speed (40 m sprint), and agility (proagility test and T-test) were performed during 3 separate testing sessions. Rate of force development (RFD) and force output at 30, 50, 90, 100, 150, 200, and 250 milliseconds of IMTP, as well as the peak value were determined. Pearson product-moment correlation analysis was used to examine the relationships between these measures. Performance in the 1RM squat was significantly correlated to the RFD between 90 and 250 milliseconds from the start of contraction (r's ranging from 0.595 to 0.748), and peak force (r = 0.866, p ≤ 0.05). One repetition maximum squat was also correlated to force outputs between 90 and 250 milliseconds (r's ranging from 0.757 to 0.816, p ≤ 0.05). Sprint time over the first 5 m in the 40 m sprint was significantly (p ≤ 0.05) correlated with peak RFD (r = -0.539) and RFD between 30 and 50 milliseconds (r's = -0.570 and -0.527, respectively). Time for the proagility test was correlated with peak RFD (r = -0.523, p ≤ 0.05) and RFD between 30 and 100 milliseconds (r's ranging from -0.518 to -0.528, p's < 0.05). Results of this investigation indicate that IMTP variables are significantly associated with strength, agility, and sprint performance. Future studies should examine IMTP as a potential tool to monitor athletic performance during the daily training of rugby union players.

49 CFR 173.417 - Authorized fissile materials packages.

Code of Federal Regulations, 2010 CFR

2010-10-01

... for export and import shipments. (2) A residual “heel” of enriched solid uranium hexafluoride may be... “Heel” in a Specification 7A Cylinder) Maximum cylinder diameter Centimeters Inches Cylinder volume Liters Cubic feet Maximum Uranium 235-enrichment (weight)percent Maximum “Heel” weight per cylinder UF6...

49 CFR 173.417 - Authorized fissile materials packages.

Code of Federal Regulations, 2011 CFR

2011-10-01

... for export and import shipments. (2) A residual “heel” of enriched solid uranium hexafluoride may be... “Heel” in a Specification 7A Cylinder) Maximum cylinder diameter Centimeters Inches Cylinder volume Liters Cubic feet Maximum Uranium 235-enrichment (weight)percent Maximum “Heel” weight per cylinder UF6...

Dynamic Response and Residual Helmet Liner Crush Using Cadaver Heads and Standard Headforms.

PubMed

Bonin, S J; Luck, J F; Bass, C R; Gardiner, J C; Onar-Thomas, A; Asfour, S S; Siegmund, G P

2017-03-01

Biomechanical headforms are used for helmet certification testing and reconstructing helmeted head impacts; however, their biofidelity and direct applicability to human head and helmet responses remain unclear. Dynamic responses of cadaver heads and three headforms and residual foam liner deformations were compared during motorcycle helmet impacts. Instrumented, helmeted heads/headforms were dropped onto the forehead region against an instrumented flat anvil at 75, 150, and 195 J. Helmets were CT scanned to quantify maximum liner crush depth and crush volume. General linear models were used to quantify the effect of head type and impact energy on linear acceleration, head injury criterion (HIC), force, maximum liner crush depth, and liner crush volume and regression models were used to quantify the relationship between acceleration and both maximum crush depth and crush volume. The cadaver heads generated larger peak accelerations than all three headforms, larger HICs than the International Organization for Standardization (ISO), larger forces than the Hybrid III and ISO, larger maximum crush depth than the ISO, and larger crush volumes than the DOT. These significant differences between the cadaver heads and headforms need to be accounted for when attempting to estimate an impact exposure using a helmet's residual crush depth or volume.

Effect of additives on the tensile performance and protein solubility of industrial oilseed residual based plastics.

PubMed

Newson, William R; Kuktaite, Ramune; Hedenqvist, Mikael S; Gällstedt, Mikael; Johansson, Eva

2014-07-16

Ten chemical additives were selected from the literature for their proposed modifying activity in protein-protein interactions. These consisted of acids, bases, reducing agents, and denaturants and were added to residual deoiled meals of Crambe abyssinica (crambe) and Brassica carinata (carinata) to modify the properties of plastics produced through hot compression molding at 130 °C. The films produced were examined for tensile properties, protein solubility, molecular weight distribution, and water absorption. Of the additives tested, NaOH had the greatest positive effect on tensile properties, with increases of 105% in maximum stress and 200% in strain at maximum stress for crambe and a 70% increase in strain at maximum stress for carinata. Stiffness was not increased by any of the applied additives. Changes in tensile strength and elongation for crambe and elongation for carinata were related to changes in protein solubility. Increased pH was the most successful in improving the protein aggregation and mechanical properties within the complex chemistry of residual oilseed meals.

DECONV-TOOL: An IDL based deconvolution software package

NASA Technical Reports Server (NTRS)

Varosi, F.; Landsman, W. B.

1992-01-01

There are a variety of algorithms for deconvolution of blurred images, each having its own criteria or statistic to be optimized in order to estimate the original image data. Using the Interactive Data Language (IDL), we have implemented the Maximum Likelihood, Maximum Entropy, Maximum Residual Likelihood, and sigma-CLEAN algorithms in a unified environment called DeConv_Tool. Most of the algorithms have as their goal the optimization of statistics such as standard deviation and mean of residuals. Shannon entropy, log-likelihood, and chi-square of the residual auto-correlation are computed by DeConv_Tool for the purpose of determining the performance and convergence of any particular method and comparisons between methods. DeConv_Tool allows interactive monitoring of the statistics and the deconvolved image during computation. The final results, and optionally, the intermediate results, are stored in a structure convenient for comparison between methods and review of the deconvolution computation. The routines comprising DeConv_Tool are available via anonymous FTP through the IDL Astronomy User's Library.

Ion-thruster propellant utilization

NASA Technical Reports Server (NTRS)

Kaufman, H. R.

1971-01-01

The evaluation and understanding of maximum propellant utilization, with mercury used as the propellant are presented. The primary-electron region in the ion chamber of a bombardment thruster is analyzed at maximum utilization. The results of this analysis, as well as experimental data from a range of ion-chamber configurations, show a nearly constant loss rate for unionized propellant at maximum utilization over a wide range of total propellant flow rate. The discharge loss level of 1000 eV/ion was used as a definition of maximum utilization, but the exact level of this definition has no effect on the qualitative results and little effect on the quantitative results. There are obvious design applications for the results of this investigation, but the results are particularly significant whenever efficient throttled operation is required.

Pesticide Residues in Food: Attitudes, Beliefs, and Misconceptions among Conventional and Organic Consumers.

PubMed

Koch, Severine; Epp, Astrid; Lohmann, Mark; Böl, Gaby-Fleur

2017-12-01

Pesticide use and pesticide residues in foods have been the subject of controversial public discussions and media coverage in Germany. Against this background, a better understanding of public risk perceptions is needed to promote efficient public health communication. To this end, this study captures the German public's perception of pesticide residues in foods. A representative sample of the population aged 14 years and older (n = 1,004) was surveyed via computer-assisted telephone interviewing on their attitudes and knowledge with regard to pesticide residues. Based on questions regarding their typical consumer behavior, respondents were classified into conventional and organic consumers to identify differences as well as similarities between these two consumer types. As assessed with an open-ended question, both organic and conventional consumers viewed pesticides, chemicals, and toxins as the greatest threats to food quality and safety. Evaluating the risks and benefits of pesticide use, more than two-thirds of organic consumers (70%) rated the risks as greater than the benefits, compared with just over one-half of conventional consumers (53%). Concern about the detection of pesticide residues in the food chain and bodily fluids was significantly higher among organic compared with conventional consumers. Only a minority of respondents was aware that legal limits for pesticide residues (referred to as maximum residue levels) exist, with 69% of organic and 61% of conventional consumers believing that the presence of pesticide residues in foods is generally not permitted. A lack of awareness of maximum residue levels was associated with heightened levels of concern about pesticide residues. Finally, general exposure to media reporting on pesticide residues was associated with more frequent knowledge of legal limits for pesticide residues, whereas actively seeking information on pesticide residues was not. The possible mechanisms underlying these findings are discussed.

Scientific basis and regulatory aspects for the toxicology of plant protection products in the European Union.

PubMed

Anadón, A; Martínez-Larrañaga, M R; Martínez, M A

2001-10-01

Authorization of plant protection products/agrochemicals/pesticides in the European Union is done on the basis of their toxicological properties. This paper reviews the current legislation for placing an agrochemical on the market (ie a new substance or a existing active substance), and the toxicology studies needed for inclusion of a substance in any of the annexes of the Council Directive of the European Economic Community 91/414/ EEC. Risk analysis and its steps is discussed. The "threshold toxicity" employed to allow risk characterisation of plant protection products is described, such as acceptable daily intake, acceptable operator exposure level, acute reference dose, and maximum admissible concentration in water.

First molecular detection of Rickettsia africae in ticks from the Union of the Comoros.

PubMed

Yssouf, Amina; Socolovschi, Cristina; Kernif, Tahar; Temmam, Sarah; Lagadec, Erwan; Tortosa, Pablo; Parola, Philippe

2014-09-22

Rickettsia africae is the agent of African tick bite fever, a disease transmitted by ticks in sub-Saharan Africa. In Union of the Comoros, a recent study reported the presence of a Rickettsia africae vector but no information has been provided on the circulation of the pathogenic agent in this country. To evaluate the possible circulation of Rickettsia spp. in Comorian cattle, genomic DNA was extracted from 512 ticks collected either in the Union of the Comoros or from animals imported from Tanzania and subsequently tested for Rickettsia infection by quantitative PCR. Rickettsia africae was detected in 90% (60/67) of Amblyomma variegatum, 1% (1/92) of Rhipicephalus appendiculatus and 2.7% (8/296) of Rhipicephalus (Boophilus) microplus ticks collected in the Union of the Comoros, as well as in 77.14% (27/35) of Amblyomma variegatum ticks collected from imported cattle. Partial sequences of both bacterial gltA and ompA genes were used in a phylogenetic analysis revealing the presence of several haplotypes, all included within the Rickettsia africae clade. Our study reports the first evidence of Rickettsia africae in ticks collected from the Union of the Comoros. The data show a significant difference of infection rate of Rickettsia africae infected ticks between the Islands, with maximum rates measured in Grande Comore Island, sheltering the main entry port for live animal importation from Tanzania. The high infection levels reported herein indicate the need for an in-depth assessment of the burden of rickettsioses in the Union of the Comoros, especially among those at risk of infection, such as cattle herders.

Dissipation rates and residues of fungicide azoxystrobin in ginseng and soil at two different cultivated regions in China.

PubMed

Hou, Zhiguang; Wang, Xiumei; Zhao, Xiaofeng; Wang, Xinhong; Yuan, Xing; Lu, Zhongbin

2016-07-01

The maximum residue limit (MRL) for fungicide azoxystrobin in ginseng has not yet been established in China. This is partially due to the lack of its dissipation and residue data at China's main ginseng production areas. In this work, the dissipation rates and residue levels of azoxystrobin in ginseng roots, plant parts (stems and leaves), and soil in Beijing and Jilin Province, China were determined using gas chromatograph-mass spectrometry (GC-MS). The mean half-life of azoxystrobin in ginseng plant parts was 1.6 days with a dissipation rate of 90 % over 21 days. The mean half-life in soil was 2.8 days with a dissipation rate of 90 % over 30 days. Dissipation rates from two geographically separated experimental fields differed, suggesting that these were affected by local soil characteristics and climate. Maximum final residues of azoxystrobin in ginseng roots, plant parts, and soil were determined to be 0.343, 9.40, and 0.726 mg kg(-1), respectively. Our results, particularly the high residues of azoxystrobin observed in ginseng plant parts, provide a quantitative basis for revising the application of this pesticide to ginseng.

Thermal Residual Stress in Environmental Barrier Coated Silicon Nitride - Modeled

NASA Technical Reports Server (NTRS)

Ali, Abdul-Aziz; Bhatt, Ramakrishna T.

2009-01-01

When exposed to combustion environments containing moisture both un-reinforced and fiber reinforced silicon based ceramic materials tend to undergo surface recession. To avoid surface recession environmental barrier coating systems are required. However, due to differences in the elastic and thermal properties of the substrate and the environmental barrier coating, thermal residual stresses can be generated in the coated substrate. Depending on their magnitude and nature thermal residual stresses can have significant influence on the strength and fracture behavior of coated substrates. To determine the maximum residual stresses developed during deposition of the coatings, a finite element model (FEM) was developed. Using this model, the thermal residual stresses were predicted in silicon nitride substrates coated with three environmental coating systems namely barium strontium aluminum silicate (BSAS), rare earth mono silicate (REMS) and earth mono di-silicate (REDS). A parametric study was also conducted to determine the influence of coating layer thickness and material parameters on thermal residual stress. Results indicate that z-direction stresses in all three systems are small and negligible, but maximum in-plane stresses can be significant depending on the composition of the constituent layer and the distance from the substrate. The BSAS and REDS systems show much lower thermal residual stresses than REMS system. Parametric analysis indicates that in each system, the thermal residual stresses can be decreased with decreasing the modulus and thickness of the coating.

40 CFR 141.54 - Maximum residual disinfectant level goals for disinfectants.

Code of Federal Regulations, 2011 CFR

2011-07-01

... for disinfectants. MRDLGs for disinfectants are as follows: Disinfectant residual MRDLG(mg/L) Chlorine 4 (as Cl 2). Chloramines 4 (as Cl 2). Chlorine dioxide 0.8 (as ClO2) [63 FR 69465, Dec. 16, 1998] ...

40 CFR 141.54 - Maximum residual disinfectant level goals for disinfectants.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for disinfectants. MRDLGs for disinfectants are as follows: Disinfectant residual MRDLG(mg/L) Chlorine 4 (as Cl 2). Chloramines 4 (as Cl 2). Chlorine dioxide 0.8 (as ClO2) [63 FR 69465, Dec. 16, 1998] ...

Commercial-scale utilization of greenhouse residues.

PubMed

Maroušek, Josef; Kondo, Yoshikazu; Ueno, Masami; Kawamitsu, Yoshinobu

2013-01-01

Development of techniques utilizing waste without any additional energy or rare catalysts is a starting point for becoming sustainable. In the present work, the complex utilization of greenhouse residues was studied on a commercial scale. Only the energy produced by the process (8%) was used to run the technology, thanks to multilevel heat recuperation and high methane yields (over 340 m(3) volatile solid t(-1) ). Manifestations of labile carbon in relation to available nitrogen, methane yields, and the formation of inhibitors were investigated in detail. The results sweep away many false beliefs about the ratios of carbon to nitrogen and highlight the role of the availability of carbon in phytomass utilization. © 2013 International Union of Biochemistry and Molecular Biology, Inc.

De-contamination of pesticide residues in food by ionizing radiation

NASA Astrophysics Data System (ADS)

Basfar, Ahmed A.; Mohamed, Khaled A.; Al-Saqer, Omar A.

2012-04-01

The role of gamma irradiation on removal of pesticides in aqueous solutions or in vegetables and fruits was investigated. Radiation - induced decontamination of pesticides is generally greater in aqueous solutions than in selected vegetables and fruits. Residues of malathion (0.5 ppm in potatoes, 8 ppm in onions and dates), pirimiphos-methyl (1 ppm in onions and grapes) and cypermethrin (0.05 ppm in potatoes and 0.1 ppm in onions) were not reduced to below maximum residue limits (MRLs) for irradiation doses up to 1 kGy. The same trend was observed when irradiation was performed for grapes fortified with malathion (8 ppm) and cypermethrin (2 ppm) for absorbed doses up to 2 kGy. Ionizing radiation reduced the residues of pirimiphos-methyl (0.05 ppm in potatoes at1 kGy, 1 ppm in grapes at 2 kGy and 0.1 ppm in dates at1 kGy), malathion (8 ppm in grapes at 7 kGy) and cypermethrin (2 ppm in grapes at 7 kGy) to below maximum residue limits (MRLs).

Liquid chromatography-tandem mass spectrometry multiresidue method for the analysis of quaternary ammonium compounds in cheese and milk products: Development and validation using the total error approach.

PubMed

Slimani, Kahina; Féret, Aurélie; Pirotais, Yvette; Maris, Pierre; Abjean, Jean-Pierre; Hurtaud-Pessel, Dominique

2017-09-29

Quaternary ammonium compounds (QACs) are both cationic surfactants and biocidal substances widely used as disinfectants in the food industry. A sensitive and reliable method for the analysis of benzalkonium chlorides (BACs) and dialkyldimethylammonium chlorides (DDACs) has been developed that enables the simultaneous quantitative determination of ten quaternary ammonium residues in dairy products below the provisional maximum residue level (MRL), set at 0.1mgkg -1 . To the best of our knowledge, this method could be the one applicable to milk and to three major processed milk products selected, namely processed or hard pressed cheeses, and whole milk powder. The method comprises solvent extraction using a mixture of acetonitrile and ethyl acetate, without any further clean-up. Analyses were performed by liquid chromatography coupled with electrospray tandem mass spectrometry detection (LC-ESI-MS/MS) operating in positive mode. A C18 analytical column was used for chromatographic separation, with a mobile phase composed of acetonitrile and water both containing 0.3% formic acid; and methanol in the gradient mode. Five deuterated internal standards were added to obtain the most accurate quantification. Extraction recoveries were satisfactory and no matrix effects were observed. The method was validated using the total error approach in accordance with the NF V03-110 standard in order to characterize the trueness, repeatability, intermediate precision and analytical limits within the range of 5-150μgkg -1 for all matrices. These performance criteria, calculated by e.noval ® 3.0 software, were satisfactory and in full accordance with the proposed provisional MRL and with the recommendations in the European Union SANTE/11945/2015 regulatory guidelines. The limit of detection (LOD) was low (<1.9μgkg -1 ) and the limit of quantification (LOQ) ranged from 5μgkg -1 to 35μgkg -1 for all matrices depending on the analytes. The validation results proved that the method is suitable for quantifying quaternary ammoniums in foodstuffs from dairy industries at residue levels, and could be used for biocide residues monitoring plans and to measure the exposition consumer to biocides products. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of heavy back squats on repeated sprint performance in trained men.

PubMed

Duncan, M J; Thurgood, G; Oxford, S W

2014-04-01

This study examined the impact of post activation potentiation on repeated sprint performance in trained Rugby Union players. Ten, male, professional Rugby Union players (mean age=25.2±5.02 years) performed 7, 30-meter sprints, separated by 25 seconds, 4 minutes following back squats (90% 1 repetition maximum) or a control condition performed in a counterbalanced order. Significant condition X sprint interactions for 10-meter (P=0.02) and 30-meter (P=0.05) indicated that times were significantly faster in the PAP condition for sprints 5, 6 and 7 across both distances. Fatigue rate was also significantly lower in the PAP condition for 10-meter (P=0.023) and 30-meter (P=0.006) sprint running speed. This study evidences that a heavy resistance exercise stimulus administered four minutes prior to repeated sprints can offset the decline in sprint performance seen during subsequent maximal sprinting over 10 and 30-meters in Rugby Union players.

Force-Velocity-Power Assessment in Semiprofessional Rugby Union Players.

PubMed

McMaster, Daniel T; Gill, Nicholas D; Cronin, John B; McGuigan, Michael R

2016-04-01

There is a constant and necessary evolution of training and assessment methods in the elite contact sports; as is required to continually improve the physical qualities of these respective athletes to match the growing sport and position-specific performance demands. Our aim was to examine the differences between ballistic upper body performance profiles and maximum upper body strength of elite rugby union forwards and backs. Twenty semiprofessional male rugby union players (age = 21.1 ± 3.0 years; mass = 94.9 ± 9.7 kg) were assessed for maximum bench press strength (1RM bench press = 121.3 ± 21.8 kg) and maximum throw power (Pmax), force (Fmax), and velocity (V[Combining Dot Above]max) from an incremental relative load testing protocol (15, 30, 45, 60, and 75% 1RM). Player rankings were also included to identify individual strength and weaknesses. The forwards were moderately stronger (effect size [ES] = 0.96; p = 0.01), produced significantly greater Fmax (ES = 1.17-1.41; p = 0.01) and were more powerful (ES = 0.57-0.64; p < 0.43) than the backs. V[Combining Dot Above]max differences were trivial to small (ES = -0.32 to -0.65; p > 0.15). There were inherent differences in strength and Fmax between the forwards and backs most likely because of the physical demands of these respective positions. Improvements in upper body strength may in turn improve ballistic force and power production, but not necessarily velocity capabilities. From the Fmax and V[Combining Dot Above]max observations, the forwards seem to be more force dominant and the backs more velocity dominant. Pmax, Fmax, and V[Combining Dot Above]max may be used to highlight proficient and deficient areas in ballistic upper body performance; the individual rankings could be further used to identify and possibly rectify individual deficiencies.

What is the relationship between free flow and pressure flow studies in women?

PubMed

Duckett, Jonathan; Cheema, Katherine; Patil, Avanti; Basu, Maya; Beale, Sian; Wise, Brian

2013-03-01

The relationship between free flow (FFS) and pressure flow (PFS) voiding studies remains uncertain and the effect of a urethral catheter on flow rates has not been determined. The relationship between residuals obtained at FF and PFS has yet to be established. This was a prospective cohort study based on 474 consecutive women undergoing cystometry using different sized urethral catheters at different centres. FFS and PFS data were compared for different conditions and the relationship of residuals analysed for FFS and PFS. The null hypothesis was that urethral catheters do not produce an alteration in maximum flow rates for PFS and FF studies. Urethral catheterisation results in lower flow rates (p < 0.01) and this finding is confirmed when flows are corrected for voided volume (p < 0.01). FFS and PFS maximum flow rates are lower in women with DO than USI (p < 0.01). A 6-F urethral catheter does not have a significantly greater effect than a 4.5-F urethral catheter. A mathematical model can be applied to transform FFS to PFS flow rates and vice versa. There was no significant difference between the mean residuals of the two groups (FFS vs PFS-two-tailed t = 0.54, p = 0.59). Positive residuals in FFS showed a good association with positive residuals in the PFS (r = 0.53, p < 0.01) Urethral catheterisation results in lower maximum flow rates. The relationship can be compared mathematically. The null hypothesis can be rejected.

Bayesian image reconstruction - The pixon and optimal image modeling

NASA Technical Reports Server (NTRS)

Pina, R. K.; Puetter, R. C.

1993-01-01

In this paper we describe the optimal image model, maximum residual likelihood method (OptMRL) for image reconstruction. OptMRL is a Bayesian image reconstruction technique for removing point-spread function blurring. OptMRL uses both a goodness-of-fit criterion (GOF) and an 'image prior', i.e., a function which quantifies the a priori probability of the image. Unlike standard maximum entropy methods, which typically reconstruct the image on the data pixel grid, OptMRL varies the image model in order to find the optimal functional basis with which to represent the image. We show how an optimal basis for image representation can be selected and in doing so, develop the concept of the 'pixon' which is a generalized image cell from which this basis is constructed. By allowing both the image and the image representation to be variable, the OptMRL method greatly increases the volume of solution space over which the image is optimized. Hence the likelihood of the final reconstructed image is greatly increased. For the goodness-of-fit criterion, OptMRL uses the maximum residual likelihood probability distribution introduced previously by Pina and Puetter (1992). This GOF probability distribution, which is based on the spatial autocorrelation of the residuals, has the advantage that it ensures spatially uncorrelated image reconstruction residuals.

Evaluation of ecological risk to populations of a threatened plant from an invasive biocontrol insect

USGS Publications Warehouse

Louda, S.M.; Rand, T.A.; Arnett, A.E.; McClay, A.S.; McEachern, A.K.

2005-01-01

This study was conducted to determine the influence of residues of organochlorine pollutants on reproductive success in the brown pelican. A sample egg was taken from each of 93 marked nests in the nesting colony in South Carolina. Periodic visits were made to determine the fate of marked nests. Each sample egg was analysed for residues of organochlorine pollutants. Nest success in the brown pelican was related to residues of DDE and dieldrin in sample eggs. DDE seemed primarily responsible for nest failure; however, deleterious effects of this pollutant on nest success were not satisfactorily separated from those induced by dieldrin. Significant intercorrelation of all five organochlorine residues identified in the eggs complicated the relationship of residues to nest success. Maximum DDE residues in an egg from a successful nest were 2.37 ?g/g and 8.48 ?g/g in an egg from an unsuccessful nest. Comparable maximum residues for dieldrin in sample eggs were 0.54 ?g/g (successful) and 0.99 ?g/g (unsuccessful). Nineteen of the 26 eggs from unsuccessful nests contained DDE residues that exceeded 2.37 ?g/g, and 14 of these 26 eggs contained dieldrin residues that exceeded O.54 ?g/g. Residues of DDD, DDT or PCBs in sample eggs were not significantly related to nest success. Reproductive success in the brown pelican colony was subnormal in the years of study--1971 and 1972--but reproductive success was normal in those nests in which the sample egg contained either <2,5 ?g/g of DDE or 0.54 ?g/g of dieldrin.

40 CFR 1065.720 - Liquefied petroleum gas.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., C3H8 Minimum, 0.85 m3/m3 ASTM D2163-05. Vapor pressure at 38 °C Maximum, 1400 kPa ASTM D1267-02 or 2598-022. Volatility residue (evaporated temperature, 35 °C) Maximum, −38 °C ASTM D1837-02a. Butanes Maximum, 0.05 m3/m3 ASTM D2163-05. Butenes Maximum, 0.02 m3/m3 ASTM D2163-05. Pentenes and heavier Maximum...

40 CFR 180.422 - Tralomethrin; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-handling establishments, including food service, manufacturing, and processing establishments, such as... shall be limited to a maximum of 0.06 percent active ingredient. Contamination of food and food-contact...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...

Biopesticides--towards increased consumer safety in the European Union.

PubMed

Czaja, Katarzyna; Góralczyk, Katarzyna; Struciński, Paweł; Hernik, Agnieszka; Korcz, Wojciech; Minorczyk, Maria; Łyczewska, Monika; Ludwicki, Jan K

2015-01-01

The introduction of new food safety regulations in the European Union has resulted in the withdrawal of many synthetic active substances used in plant protection products, in light of their potential or actual harmful effect on human and animal health, as well as on the environment. Alternatives to these compounds are being developed - naturally occurring pesticides, also referred to as biopesticides. The use of biopesticides in crop protection leads to decreased levels of pesticide residues in foods, and as a result to lower risk levels for the consumer. Biologically active agents defined as biopesticides are varied, and therefore application of the same environmental and consumer safety criteria to all of them is impossible. This presents serious complications in the approval of these pesticides as active plant protection products and in their registration. It needs to be stressed that, in the registration procedure of the European Union, biopesticides are subject to the same regulations as synthetic active substances. This situation has resulted in the need to introduce numerous new provisions in the legislation, as well as the preparation of new guidelines facilitating the registration of biopesticides. These activities aim to promote naturally originating pesticides. © 2014 Society of Chemical Industry.

40 CFR 141.60 - Effective dates.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS National Primary Drinking Water Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.60 Effective dates. (a) The effective dates for § 141...

Aluminum-thin-film packaged fiber Bragg grating probes for monitoring the maximum tensile strain of composite materials.

PubMed

Im, Jooeun; Kim, Mihyun; Choi, Ki-Sun; Hwang, Tae-Kyung; Kwon, Il-Bum

2014-06-10

In this paper, new fiber Bragg grating (FBG) sensor probes are designed to intermittently detect the maximum tensile strain of composite materials, so as to evaluate the structural health status. This probe is fabricated by two thin Al films bonded to an FBG optical fiber and two supporting brackets, which are fixed on the surface of composite materials. The residual strain of the Al packaged FBG sensor probe is induced by the strain of composite materials. This residual strain can indicate the maximum strain of composite materials. Two types of sensor probes are prepared-one is an FBG with 18 μm thick Al films, and the other is an FBG with 36 μm thick Al films-to compare the thickness effect on the detection sensitivity. These sensor probes are bonded on the surfaces of carbon fiber reinforced plastics composite specimens. In order to determine the strain sensitivity between the residual strain of the FBG sensor probe and the maximum strain of the composite specimen, tensile tests are performed by universal testing machine, under the loading-unloading test condition. The strain sensitivities of the probes, which have the Al thicknesses of 18 and 36 μm, are determined as 0.13 and 0.23, respectively.

Intramedullary fixation of forearm fractures with new locked nail.

PubMed

Bansal, Himanshu

2011-09-01

Lack of availability of interlocked nails made plate osteosynthesis the first choice of treatment of forearm fractures inspite of more surgical exposure, periosteal stripping and big skin incision subsequent scar along with higher risk of refracture on implant removal. We hereby report the first 12 cases with 19 forearm bone fractures internally fixed by indegenous interlocked nail. Existing square nails were modified to have a broad proximal end of 5.5 mm with a hole for locking screw of 2.5 mm. The nail has a distal hole of 1/1.2/1.5 mm in 2.5/3/3.5 mm diameter nail, respectively. A new method of distal locking with a clip made of k wire is designed. The clip after insertion into the bone and hole in nail and opposite cortex snuggly fits the bone providing a secure locking system. Twelve skeletally mature patients, mean age 32 years (range 24-45 years) with 19 diaphyseal fractures of the forearm were treated with this indigenously made new nail. The patient were evaluated for fracture union, functional recovery and complications. The functional outcome was assessed by disabilities of arm, shoulder and hand questionnaire (DASH score). Time to radiographic union ranged between 12 and 28 weeks, with a 100% union rate. Complications were minimal, with mild infection in open fracture (n=1) and delayed union (n=1) in patient with comminuted fracture of the ulna only. The clinical results were excellent. The DASH score ranged between 0 and 36 points. This new interlocking nail may be considered as an alternative to plate osteosynthesis for fractures of the forearm in adults. The advantages are benefit of closed reduction, smaller residual scar, reduced cost and early union with allowance of immediate movements.

Use of body plethysmography to measure effect of bimaxillary orthognathic surgery on airway resistance and lung volumes.

PubMed

Rezaeetalab, Fariba; Kazemian, Mozhgan; Vaezi, Touraj; Shaban, Barratollah

2015-12-01

Bimaxillary orthognathic surgery can cause changes to respiration and the airways. We used body plethysmography to evaluate its effect on airway resistance and lung volumes in 20 patients with class III malocclusions (8 men and 12 women, aged 17 - 32 years). Lung volumes (forced vital capacity; forced inspiratory volume/one second; forced expiratory volume/one second: forced vital capacity; peak expiratory flow; maximum expiratory flow 25-75; maximum inspiratory flow; total lung capacity; residual volume; residual volume:total lung capacity), and airway resistance were evaluated one week before, and six months after, operation. Bimaxillary operations to correct class III malocclusions significantly increased airway resistance, residual volume, total lung capacity, and residual volume:total lung capacity. Other variables also changed after operation but not significantly so. Orthognathic operations should be done with caution in patients who have pre-existing respiratory diseases. Copyright © 2015 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

75 FR 53841 - Display of Official Sign; Permanent Increase in Standard Maximum Share Insurance Amount

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-02

... to replace the old version of the official sign with the revised official sign at required locations.... Additionally, a credit union must replace the old version of the official sign with the revised official sign... internet signs and deplete its stockpiles of other printed advertising materials. NCUA also believes that...

12 CFR 745.4 - Revocable trust accounts.

Code of Federal Regulations, 2011 CFR

2011-01-01

...-death account naming the same niece and a friend as beneficiaries. The maximum coverage available to the... beneficiaries in the revocable trust accounts—his niece and cousin in the first, and the same niece and a friend... names two friends, “B” and “C” as beneficiaries. At the same NCUA-insured credit union, A establishes a...

Multiwalled carbon nanotubes as solid-phase extraction materials for the gas chromatographic determination of organophosphorus pesticides in waters.

PubMed

Ravelo-Pérez, Lidia M; Hernández-Borges, Javier; Angel Rodríguez-Delgado, Miguel

2008-10-01

In the present work, a GC method with nitrogen-phosphorus detection (NPD) was developed for the simultaneous determination of eight organophosphorus pesticide (OPP) residues (i.e., ethoprofos, diazinon, chlorpyrifos-methyl, fenitrothion, malathion, chlorpyrifos, fenamiphos, and buprofezin) in water samples. Preconcentration of the water samples was carried out using an SPE procedure with multiwalled carbon nanotubes (MWCNTs) of 10-15 nm od, 2-6 nm id, and 0.1-10 microm length as stationary phase. Extraction parameters, such as the amount of MWCNTs, sample volume, pH, and type and amount of the eluent were optimized. The most favorable conditions were as follows: 40 mg MWCNTs, 800 mL water, pH 6.0, and 20 mL dichloromethane, respectively. The MWCNTs-SPE-GC-NPD method was applied to the determination of these pesticides in real water samples: mineral and ground water as well as run-off water from an agricultural area collected shortly before opening out onto the sea. A recovery study was developed with five consecutive extractions of the three types of water spiked at three concentration levels (n = 15). Mean recovery values were in the range of 75-116% for mineral water (RSD < 6.3%), 67-119% for ground water (RSD < 5.8%), and 57-81% for run-off waters (RSDs < 6.9%), except for fenamiphos (mean recovery values between 40 and 84% for the three types of waters, RSDs < 8.9%). LODs were in the low ng/L level (i.e., levels below the maximum residue limits (MRLs) established by the European Union (EU) legislation for these compounds in waters). The proposed method was also applied to the analysis of six water samples (two of each type: mineral, ground, and run-off waters) in which no residues of the selected pesticides were found. Results show that the MWCNTs used in this work have a high adsorbability of the pesticides under study. The main advantage of the use of these MWCNTs is their low cost when compared with those MWCNTs previously used in the literature and with conventional SPE cartridges.

Extraction of manganese from electrolytic manganese residue by bioleaching.

PubMed

Xin, Baoping; Chen, Bing; Duan, Ning; Zhou, Changbo

2011-01-01

Extraction of manganese from electrolytic manganese residues using bioleaching was investigated in this paper. The maximum extraction efficiency of Mn was 93% by sulfur-oxidizing bacteria at 4.0 g/l sulfur after bioleaching of 9days, while the maximum extraction efficiency of Mn was 81% by pyrite-leaching bacteria at 4.0 g/l pyrite. The series bioleaching first by sulfur-oxidizing bacteria and followed by pyrite-leaching bacteria evidently promoted the extraction of manganese, witnessing the maximum extraction efficiency of 98.1%. In the case of sulfur-oxidizing bacteria, the strong dissolution of bio-generated sulfuric acid resulted in extraction of soluble Mn2+, while both the Fe2+ catalyzed reduction of Mn4+ and weak acidic dissolution of Mn2+ accounted for the extraction of manganese with pyrite-leaching bacteria. The chemical simulation of bioleaching process further confirmed that the acid dissolution of Mn2+ and Fe2+ catalyzed reduction of Mn4+ were the bioleaching mechanisms involved for Mn extraction from electrolytic manganese residues. Copyright © 2010 Elsevier Ltd. All rights reserved.

Comparison of the composting process using ear corn residue and three other conventional bulking agents during cow manure composting under high-moisture conditions.

PubMed

Hanajima, Dai

2014-10-01

To elucidate the characteristics of ear corn residue as a bulking agent, the composting process using this residue was compared with processes using three other conventional materials such as sawdust, wheat straw and rice husk, employing a bench-scale composting reactor. As evaluated via biochemical oxygen demand (BOD), ear corn residue contains 3.3 and 2.0 times more easily digestible materials than sawdust and rice husk, respectively. In addition, mixing ear corn residue with manure resulted in reduced bulk density, which was the same as that of wheat straw and was 0.58 and 0.67 times lower than that of sawdust and a rice husk mixture, respectively. To evaluate temperature generation during the composting process, the maximum temperature and area under the temperature curve (AUCTEMP) were compared among the mixed composts of four bulking agents. Maximum temperature (54.3°C) as well as AUCTEMP (7310°C●h) of ear corn residue were significantly higher than those of sawdust and rice husk (P<0.05), and they are similar to that of wheat straw mixed compost. Along with the value of AUCTEMP, the highest organic matter losses of 31.1% were observed in ear corn residue mixed compost, followed by wheat straw, saw dust and rice husk. © 2014 Japanese Society of Animal Science.

Occurrence of pesticide residues in fruiting vegetables from production farms in south-eastern region of Poland

PubMed

Słowik-Borowiec, Magdalena; Szpyrka, Ewa; Rupar, Julian; Podbielska, Magdalena; Matyaszek, Aneta

Considering the fact that pesticides are commonly used in agriculture, continuous monitoring of these substances in food products is of great significance. Residues of these substances can be present in crops after harvest. The aim of this study was to evaluate presence of pesticide residues in fruiting vegetables from production farms in south-eastern region of Poland in 2012–2015. 138 samples were tested using accredited test methods. The monitoring programme covered determination of 242 pesticides. The tests covered tomato, cucumber and pepper crops. The test results were interpreted in accordance with criteria included in the European Commission recommendations published in the document SANCO/12571/2013 (now superseded by Document SANTE 2015), as well as on a basis of the maximum residue levels in force in the EU Member States. Pesticide residues were found in 47 samples, representing 34% of all tested samples. 17 active substances were found, belonging to fungicides and insecticides. Azoxystrobin (38%), boscalid (28%) and chlorothalonil (21%) were most commonly found in fruiting vegetables testing samples. Non-compliances related to use of plant protection product not authorized for protection of a given crop were observed in 6% of analysed samples. However, pesticide residues of fruiting vegetables in quantities that exceed the maximum residue levels (NDP, ang. MRLs), as well as substances which use for plant protection is forbidden were no found. Crops monitoring is used to determine to what extent such products are contaminated with pesticide residues, and ensures protection of customer health.

Pesticides and their metabolites in wells of Suffolk County, New York, 1998

USGS Publications Warehouse

Phillips, Patrick J.; Eckhardt, D.A.; Terracciano, S.A.; Rosenmann, Larry

1999-01-01

Five insecticide residues and 20 herbicide residues were detected in water samples collected from 50 shallow wells screened in the surficial sand and gravel aquifer in Suffolk County, Long Island in areas with known or suspected residues. Laboratory analytical methods with extremely low detection limits - from 0.001 to 0.2 ?g/L (micrograms per liter) - were used to analyze the samples for 60 pesticide residues. Forty-four of the samples contained at least one pesticide residue, and some samples contained as many as 11 different pesticides or pesticide metabolites. Only four water- quality standards were exceeded in the samples collected in this study. Dieldrin exceeded the New York State Class GA standard (0.004 ?g/L) in samples from eight wells. The Federal and New York State Maximum Contaminant Level for simazine (4 ?g/L) was exceeded in samples from two wells, and the State Class GA standard for simazine (0.5 ?g/L) was exceeded in samples from six wells. Federal water-quality standards have not been established for many of the compounds detected in this study, including herbicide metabolites. Maximum concentrations of four herbicide metabolites -metolachlor ESA (ethanesulfonic acid), metolachlor OA (oxanilic acid), and the alachlor metabolites alachlor ESA and alachlor OA -exceeded 20 ?g/L. The maximum concentration of one herbicide (tebuthiuron) exceeded 10 ?g/L, and the maximum concentration of three herbicides (simazine, metolachlor, and atrazine) and one herbicide metabolite (deisopropylatrazine) ranged from 1 to 10 ?g/L. The herbicide metolachlor, which is used on potato fields in Suffolk County, and its metabolites (metolachlor ESA and metolachlor OA) were most frequently detected in samples from agricultural areas. The herbicides simazine and tebuthiuron, which were used in utility rights-of-way, and the simazine metabolite deisopropylatrazine were detected at concentrations greater than 0.05 ?g/L most frequently in samples from residential and mixed land-use areas. The results of this investigation are not necessarily representative of conditions throughout the remainder of Long Island, because these samples were collected in areas of known or suspected residues.

Potential for polyhydroxyalkanoate production on German or European municipal waste water treatment plants.

PubMed

Pittmann, T; Steinmetz, H

2016-08-01

Biopolymers, which are made of renewable raw materials and/or biodegradable residual materials present a possible alternative to common plastic. A potential analysis, based on experimental results in laboratory scale and detailed data from German waste water treatment plants, showed that the theoretically possible production of biopolymers in Germany amounts to more than 20% of the 2015 worldwide biopolymer production. In addition a profound estimation regarding all European Union member states showed that theoretically about 115% of the actual worldwide biopolymer production could be produced on European waste water treatment plants. With an upgraded biopolymer production and a theoretically reachable biopolymer proportion of around 60% of the cell dry weight a total of 1,794,656tPHAa or approximately 236% of today's biopolymer production could be produced on waste water treatment plants in the European Union, using primary sludge as raw material only. Copyright © 2016 Elsevier Ltd. All rights reserved.

Risks of antibiotic residues in milk following intramammary and intramuscular treatments in dairy sheep.

PubMed

Pengov, A; Kirbis, A

2009-04-01

Very few drugs on the market are approved for use in lactating ewes. Veterinarians in the European Union are allowed to prescribe drugs in an off-label manner but are then obligated to assure that residues do not enter the food chain. In case of mastitis treatment in dairy ewes antibiotic preparations designed and authorized for the bovine mammary gland are usually used. Due to inter-species differences, available bovine data cannot be accurately extrapolated for use in the dairy ewe. The objective of the study was therefore to determine appropriate withdrawal periods for ewe's milk following mastitis treatment with two commercial lactating cow products. For the detection of all components standard agar plate diffusion techniques were used. Regardless of the therapy regime and the product used, residues of antibiotics in milk were detected up to 192h after the last infusion. These results indicate that the required withholding periods for ewe's milk are considerably longer than recommended on the label for bovine milk.

Selection of the Maximum Spatial Cluster Size of the Spatial Scan Statistic by Using the Maximum Clustering Set-Proportion Statistic.

PubMed

Ma, Yue; Yin, Fei; Zhang, Tao; Zhou, Xiaohua Andrew; Li, Xiaosong

2016-01-01

Spatial scan statistics are widely used in various fields. The performance of these statistics is influenced by parameters, such as maximum spatial cluster size, and can be improved by parameter selection using performance measures. Current performance measures are based on the presence of clusters and are thus inapplicable to data sets without known clusters. In this work, we propose a novel overall performance measure called maximum clustering set-proportion (MCS-P), which is based on the likelihood of the union of detected clusters and the applied dataset. MCS-P was compared with existing performance measures in a simulation study to select the maximum spatial cluster size. Results of other performance measures, such as sensitivity and misclassification, suggest that the spatial scan statistic achieves accurate results in most scenarios with the maximum spatial cluster sizes selected using MCS-P. Given that previously known clusters are not required in the proposed strategy, selection of the optimal maximum cluster size with MCS-P can improve the performance of the scan statistic in applications without identified clusters.

Selection of the Maximum Spatial Cluster Size of the Spatial Scan Statistic by Using the Maximum Clustering Set-Proportion Statistic

PubMed Central

Ma, Yue; Yin, Fei; Zhang, Tao; Zhou, Xiaohua Andrew; Li, Xiaosong

2016-01-01

Spatial scan statistics are widely used in various fields. The performance of these statistics is influenced by parameters, such as maximum spatial cluster size, and can be improved by parameter selection using performance measures. Current performance measures are based on the presence of clusters and are thus inapplicable to data sets without known clusters. In this work, we propose a novel overall performance measure called maximum clustering set–proportion (MCS-P), which is based on the likelihood of the union of detected clusters and the applied dataset. MCS-P was compared with existing performance measures in a simulation study to select the maximum spatial cluster size. Results of other performance measures, such as sensitivity and misclassification, suggest that the spatial scan statistic achieves accurate results in most scenarios with the maximum spatial cluster sizes selected using MCS-P. Given that previously known clusters are not required in the proposed strategy, selection of the optimal maximum cluster size with MCS-P can improve the performance of the scan statistic in applications without identified clusters. PMID:26820646

7 CFR 58.140 - Field service.

Code of Federal Regulations, 2012 CFR

2012-01-01

... each producer whose milk tests positive for drug residue, exceeds the maximum somatic cell count level... milk and eliminate any potential causes of drug residues. A representative of the plant should routinely visit each producer as often as necessary to assist and encourage the production of high quality...

7 CFR 58.140 - Field service.

Code of Federal Regulations, 2011 CFR

2011-01-01

... each producer whose milk tests positive for drug residue, exceeds the maximum somatic cell count level... milk and eliminate any potential causes of drug residues. A representative of the plant should routinely visit each producer as often as necessary to assist and encourage the production of high quality...

7 CFR 58.140 - Field service.

Code of Federal Regulations, 2013 CFR

2013-01-01

... each producer whose milk tests positive for drug residue, exceeds the maximum somatic cell count level... milk and eliminate any potential causes of drug residues. A representative of the plant should routinely visit each producer as often as necessary to assist and encourage the production of high quality...

7 CFR 58.140 - Field service.

Code of Federal Regulations, 2010 CFR

2010-01-01

... each producer whose milk tests positive for drug residue, exceeds the maximum somatic cell count level... milk and eliminate any potential causes of drug residues. A representative of the plant should routinely visit each producer as often as necessary to assist and encourage the production of high quality...

7 CFR 58.140 - Field service.

Code of Federal Regulations, 2014 CFR

2014-01-01

... each producer whose milk tests positive for drug residue, exceeds the maximum somatic cell count level... milk and eliminate any potential causes of drug residues. A representative of the plant should routinely visit each producer as often as necessary to assist and encourage the production of high quality...

Assessment of agroforestry residue potentials for the bioeconomy in the European Union.

PubMed

Thorenz, Andrea; Wietschel, Lars; Stindt, Dennis; Tuma, Axel

2018-03-01

The biobased chemical industry is characterised by strong growth. Innovative products and materials such as biopolymers have been developed, and current European demand for biopolymers exceeds the domestic supply. Agroforestry residues can serve as main sources of the basic building blocks for chemicals and materials. This work assesses sustainably available agroforestry residues to feed a high added-value materials and product bioeconomy. To evaluate bioeconomic potential, a structured three-step approach is applied. Cultivation practices, sustainability issues, legislative restrictions, technical limitations and competitive applications are considered. All data regarding bioeconomic potential are processed on a regional level and mapped by ArcGIS. Our results identify wheat straw as the most promising source in the agricultural sector, followed by maize stover, barley straw and rape straw, which all contain a total concentration of lignocellulose of more than 80% of dry matter. In the forestry sector, residue bark from two coniferous species, spruce and pine, is the most promising source, with approximately 70% lignocellulose. Additionally, coniferous bark contains considerable amounts of tannin, which has attracted increasing interest for industrial utilisation. A sensitivity analysis concerning removal rates, residue-to-crop ratios, changes in farming technologies and competing applications is applied at the end of the study to consolidate our results.

SERS strategy based on the modified Au nanoparticles for highly sensitive detection of bisphenol A residues in milk.

PubMed

Yang, Libin; Chen, Yongliang; Shen, Yu; Yang, Ming; Li, Xiuling; Han, Xiaoxia; Jiang, Xin; Zhao, Bing

2018-03-01

Bisphenol A (BPA) is a highly toxic chemical, and its residue in milk product is threatening people's health due to its possible leaching from the packagings and cans with BPA coating. In this work, halides modified Au nanoparticles (NPs) as the modification substrates were first designed for rapid and sensitive determination of BPA residue in real milk by SERS method with the assistance of aggregation agents (Zn 2+ ). It can be concluded that Au NPs modification substrate with assistance of the aggregation agent can remarkably improve the detection sensitivity of BPA residue, which can significantly enhance the SERS signal of BPA and achieve the trace-level detection of BPA residue. Under the optimal conditions, the limit of detection of BPA residue can be as low as to 4.3 × 10 -9 mol/L (equal to 0.98 × 10 -3 mg/kg), which is much less than the standard of European Union (0.6mg/kg). And, there is a good linear relationship (R 2 = 0.990) between the intensity of SERS signal and the logarithm of BPA concentration in the range of 1.0 × 10 -8 -1.0 × 10 -3 mol/L. By this method, the recovery of BPA residue ranges from 89.5% to 100.2% with relative standard deviation between 4.6% and 2.7%. The proposed SERS method proves to be reliable, highly sensitive and possesses good reproducibility, which is very promising for sensitive detection of bisphenols residue in foodstuff. Copyright © 2017 Elsevier B.V. All rights reserved.

Immunology-Based Techniques for the Detection of Veterinary Drug Residues in Foods

NASA Astrophysics Data System (ADS)

Reig, Milagro; Toldrá, Fidel

Veterinary drugs are used in farm animals, via the feed or the drinking water, to prevent the outbreak of diseases or even for the treatment of diseases. However, the growth of animals may be promoted through the use of hormones and antibiotics. Depending on the type of residue and the application and washing conditions, these substances or its metabolites may remain in meat and other foods of animal origin and may cause adverse effects on consumers’ health. This is the main reason why its use is strictly regulated or even banned (case of the European Union) in different countries. Antibiotics typically used for growth promotion include chloramphenicol, nitrofurans, and enrofloxacin but others like sulphonamides, macrolides etc. may also be used (Reig & Toldrá, 2007).

Dissipation of Flonicamid in Honeysuckle and Its Transfer during Brewing Process.

PubMed

Wang, Yujie; Xue, Jian; Jin, Hongyu; Ma, Shuangcheng

2017-05-01

The dissipation of flonicamid in Honeysuckle and transfer pattern from Honeysuckle to its tea infusion were investigated. Flonicamid was applied on Honeysuckle crop at two dosages, 60 g of active gradient per hectare (g a.i. hm -2 ) and 180 g a.i. hm -2 (recommended and triple the recommended) in Fenqiu, Henan Province in 2015 and 2016. Gas Chromatography-Electron Capture Detector (GC-ECD) detection methods were developed for the analysis of flonicamid residues in honeysuckles and its infusion. The recoveries in both honeysuckles and its infusion ranged from 81.5 to 101.7% with relative standard deviations (RSDs) of 3.2-9.1%. The dissipations of flonicamid in Honeysuckle were found to follow the first order kinetics with half-life ranging between 2.8 and 3.2 d. After recommended dose pesticide application, contents of flonicamid residues were lower than theoretical maximum residue limit (tMRL). Flonicamid residues can easily transfer from Honeysuckle to its tea infusion and transfer rates of flonicamid decrease with the brewing temperature reduction or the brewing times increase. These results are helpful to establish maximum residue limit and develop guidance on the appropriate and secure use of flonicamid in Honeysuckle.

Evaluation of pesticide residues of organochlorine in vegetables and fruits in Qatar: statistical analysis.

PubMed

Al-Shamary, Noora M; Al-Ghouti, Mohammad A; Al-Shaikh, Ismail; Al-Meer, Saeed H; Ahmad, Talaat A

2016-03-01

The study aimed to examine the residues of organochlorines pesticides (OCPs) in vegetables and fruits in Qatar. A total of 127 samples was studied. Ninety percent of the imported samples recorded residues above the maximum residue levels (MRLs). The most frequently detected OCP in the samples was heptachlor (found in 75 samples). In the comparisons between the washed and unwashed samples, no significant differences were observed (P > 0.05). However, the effect of washing process with tap water depended on the type of vegetables and fruits.

Capillary Trapping of CO2 in Oil Reservoirs: Observations in a Mixed-Wet Carbonate Rock.

PubMed

Al-Menhali, Ali S; Krevor, Samuel

2016-03-01

Early deployment of carbon dioxide storage is likely to focus on injection into mature oil reservoirs, most of which occur in carbonate rock units. Observations and modeling have shown how capillary trapping leads to the immobilization of CO2 in saline aquifers, enhancing the security and capacity of storage. There are, however, no observations of trapping in rocks with a mixed-wet-state characteristic of hydrocarbon-bearing carbonate reservoirs. Here, we found that residual trapping of supercritical CO2 in a limestone altered to a mixed-wet state with oil was significantly less than trapping in the unaltered rock. In unaltered samples, the trapping of CO2 and N2 were indistinguishable, with a maximum residual saturation of 24%. After the alteration of the wetting state, the trapping of N2 was reduced, with a maximum residual saturation of 19%. The trapping of CO2 was reduced even further, with a maximum residual saturation of 15%. Best-fit Land-model constants shifted from C = 1.73 in the water-wet rock to C = 2.82 for N2 and C = 4.11 for the CO2 in the mixed-wet rock. The results indicate that plume migration will be less constrained by capillary trapping for CO2 storage projects using oil fields compared with those for saline aquifers.

Impact of downward-mixing ozone on surface ozone accumulation in southern Taiwan.

PubMed

Lin, Ching-Ho

2008-04-01

The ozone that initially presents in the previous day's afternoon mixing layer can remain in the nighttime atmosphere and then be carried over to the next morning. Finally, this ozone can be brought to the ground by downward mixing as mixing depth increases during the daytime, thereby increasing surface ozone concentrations. Variation of ozone concentration during each of these periods is investigated in this work. First, ozone concentrations existing in the daily early morning atmosphere at the altitude range of the daily maximum mixing depth (residual ozone concentrations) were measured using tethered ozonesondes on 52 experimental days during 2004-2005 in southern Taiwan. Daily downward-mixing ozone concentrations were calculated by a box model coupling the measured daily residual ozone concentrations and daily mixing depth variations. The ozone concentrations upwind in the previous day's afternoon mixing layer were estimated by the combination of back air trajectory analysis and known previous day's surface ozone distributions. Additionally, the relationship between daily downward-mixing ozone concentration and daily photochemically produced ozone concentration was examined. The latter was calculated by removing the former from daily surface maximum ozone concentration. The measured daily residual ozone concentrations distributed at 12-74 parts per billion (ppb) with an average of 42 +/- 17 ppb are well correlated with the previous upwind ozone concentration (R2 = 0.54-0.65). Approximately 60% of the previous upwind ozone was estimated to be carried over to the next morning and became the observed residual ozone. The daily downward-mixing ozone contributes 48 +/- 18% of the daily surface maximum ozone concentration, indicating that the downward-mixing ozone is as important as daily photochemically produced ozone to daily surface maximum ozone accumulation. The daily downward-mixing ozone is poorly correlated with the daily photochemically produced ozone and contributes significantly to the daily variation of surface maximum ozone concentrations (R2 = 0.19). However, the contribution of downward-mixing ozone to daily ozone variation is not included in most existing statistical models developed for predicting daily ozone variation. Finally, daily surface maximum ozone concentration is positively correlated with daily afternoon mixing depth, attributable to the downward-mixing ozone.

Effects of water pH on the uptake and elimination of the piscicide, 3-trifluoromethyl-4-nitrophenol (TFM), by larval sea lamprey.

PubMed

Hlina, Benjamin L; Tessier, Laura R; Wilkie, Michael P

2017-10-01

Invasive sea lamprey (Petromyzon marinus) populations in the Great Lakes are controlled by applying the piscicide, 3-trifluoromethyl-4-nitrophenol (TFM), to infested streams with larval sea lamprey (ammocoetes). While treatment mortality is >90%, surviving lamprey, called residuals, can undermine control efforts. A key determinant of TFM effectiveness is water pH, which can fluctuate daily and seasonally in surface waters. The objectives of this research were to evaluate the influence of pH on the uptake, elimination, and accumulation of TFM by larval sea lamprey using radio-labeled TFM ( 14 C-TFM), when exposed to a nominal concentration of 4.6mgTFML -1 or 7.6mgTFML -1 , 3h or 1h, respectively. TFM uptake rates were approximately 5.5-fold greater at low pH (6.86) compared to the high pH (8.78), most likely due to the unionized, lipophilic form of TFM existing in greater amounts at a lower pH. In contrast, elimination rates following the injection of 85nmolTFMg -1 body mass were 1.7-1.8 fold greater at pH8.96 than at pH6.43 during 2-4h of depuration in TFM-free water. Greater initial excretion rates at pH8.96 were presumably due to predicted increases in outward concentration gradients of un-ionized TFM. The present findings suggest that TFM is mainly taken-up in its un-ionized form, more lipophilic form, but there is also significant uptake of the ionized form of TFM via an unknown mechanism. Moreover, we provide an explanation to how small increases in pH can undermine lampricide treatment success increasing residual lamprey populations. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Pretreatment of bamboo residues with Coriolus versicolor for enzymatic hydrolysis.

PubMed

Zhang, Xiaoyu; Xu, Chunyan; Wang, Hongxun

2007-08-01

Pretreatment by a white-rot fungus Coriolus versicolor B1 under different conditions and saccharification of bamboo were investigated. The saccharification rate was significantly enhanced and a maximum saccharification rate of 37.0% was achieved after pretreatment. Reducing sugars yield was 223.2 mg/g of bamboo residues, which was 2.34 times that of the raw material. It was feasible to treat bamboo residues with B1 for the saccharification of bamboo.

Nanohardness and Residual Stress in TiN Coatings.

PubMed

Hernández, Luis Carlos; Ponce, Luis; Fundora, Abel; López, Enrique; Pérez, Eduardo

2011-05-17

TiN films were prepared by the Cathodic arc evaporation deposition method under different negative substrate bias. AFM image analyses show that the growth mode of biased coatings changes from 3D island to lateral when the negative bias potential is increased. Nanohardness of the thin films was measured by nanoindentation, and residual stress was determined using Grazing incidence X ray diffraction. The maximum value of residual stress is reached at -100 V substrate bias coinciding with the biggest values of adhesion and nanohardness. Nanoindentation measurement proves that the force-depth curve shifts due to residual stress. The experimental results demonstrate that nanohardness is seriously affected by the residual stress.

Concentrations of dioxins and dioxin-like PCBs in feed materials in the Netherlands, 2001-11.

PubMed

Adamse, Paulien; Van der Fels-Klerx, H J Ine; Schoss, Stefanie; de Jong, Jacob; Hoogenboom, Ron L A P

2015-01-01

This study aimed to obtain insights into contamination of feed materials used in the Netherlands with dioxins (polychlorinated dibenzo-p-dioxins and dibenzofurans) and dioxin-like polychlorinated biphenyls (PCBs). Monitoring results from the period 2001-11, covering in total 4938 samples, were statistically analysed and evaluated against the statutory limits set at the beginning or during this period. The percentage of samples exceeding maximum levels set within the European Union for either dioxins or the sum of dioxins and dioxin-like PCBs were below 1% for most feed categories, except for fish meal (4.1%), clay minerals (binders and anti-caking agents) (3.4%), and vegetable oils and byproducts (1.7%). For most feed categories, non-compliance with the action threshold (roughly 33% lower than maximum levels) for either dioxins or dioxin-like PCBs was up to three times higher than non-compliance with the respective maximum levels. Exceedance of action thresholds was just above 1% for animal fat, pre-mixtures and feed materials of plant origin excluding vegetable oils. For the categories fish meal, clay minerals, and vegetable oils and byproducts, the action thresholds were exceeded by 5.0%, 9.8% and 3.0% of the samples, respectively. In general, the percentages of samples that exceeded the action thresholds and maximum levels were lower than those reported for the European Union by the European Food Safety Authority (EFSA). In most of the feed materials, there seems to be a decreasing trend in concentrations of dioxins or dioxin-like PCBs over the years. However, a lowering of the limits of quantification during this period and the low concentrations in most samples precludes drawing strong conclusions.

Residue depletion of ivermectin in broiler poultry.

PubMed

Mestorino, Nora; Buldain, Daniel; Buchamer, Andrea; Gortari, Lihuel; Daniele, Martín; Marchetti, María Laura

2017-04-01

Helminth infections are widespread in the poultry industry. There is evidence of extra-label use of some drugs, such as ivermectin (IVM), in broiler poultry. Pharmacokinetic and residual studies of IVM in poultry, however, are rather scarce. Our aim was to determine time restrictions for broiler chickens fed with balanced feed mixed with IVM for 21 days, and thus achieve acceptable residual levels for consumption as established by the European Union. Sixty 1-day-old chicks were fed with food supplemented with IVM at 5 mg kg -1 feed for 21 days. Groups of six treated animals were sacrificed at 0, 1, 2, 4, 8, 10, 15, 20 and 28 days after treatment. Liver, skin/fat, kidney and muscle samples were obtained. IVM were determined by liquid chromatography with fluorescence detection after automatic solid-phase extraction with SPE C 18 cartridges. The highest concentrations were measured in the liver, which is logical given that IVM is a drug that undergoes extensive hepatic metabolism. The optimal withdrawal time for edible tissues of these animals to stay within the permitted residual levels were: 12 days for liver, 8 days for skin/fat, 0 days for muscle and 10 days for kidney.

12 CFR 713.6 - What is the permissible deductible?

Code of Federal Regulations, 2011 CFR

2011-01-01

... based on it having assets in excess of $1 million as reflected in its most recent year-end 5300 call... assets up to a maximum of $200,000; for credit unions over $1 million in assets that qualify for NCUA's... 12 Banks and Banking 6 2011-01-01 2011-01-01 false What is the permissible deductible? 713.6...

12 CFR 713.6 - What is the permissible deductible?

Code of Federal Regulations, 2012 CFR

2012-01-01

... based on it having assets in excess of $1 million as reflected in its most recent year-end 5300 call... assets up to a maximum of $200,000; for credit unions over $1 million in assets that qualify for NCUA's... 12 Banks and Banking 7 2012-01-01 2012-01-01 false What is the permissible deductible? 713.6...

Proposal for National Targets in the Framework of the European Reduction Goal for Early School Leaving

ERIC Educational Resources Information Center

Lastra-Bravo, Xavier B.; Tolón-Becerra, Alfredo; Salinas-Andújar, José A.

2013-01-01

According to the European Commission's "Europe 2020" strategy, the early school leaving (ESL) rate in European Union (EU) Member States must be reduced to a maximum of 10 per cent by 2020. This paper proposes a nonlinear distribution method based on dynamic targets for reducing the percentage of early school leavers. The aim of this…

Manufacture of reconstruction-bricks in Mexico

NASA Astrophysics Data System (ADS)

Rojas-Valencia, Ma. Neftalí; Penagos, Armando Aguilar; Rojas, Denise Y. Fernández; López, Alberto López; Gálves, David Morillón

2017-12-01

In Mexico, around 33.600 tons of construction wastes are generated every day, Mexico City contributing for around tons/day, with fewer than 1.000 tons/day being sent to be recycled. For that reason the purpose of this study was to manufacture sustainable bricks, based on three types of wastes generated in the building industry: wood cutting residues, wastes from the excavation process (From Coapa and Cuautlancingo, Puebla, Mexico) and recycled aggregates. Water was added as kneading material, and Opuntia ficus-indica (mucilage) was supplemented as natural additive to improve the workability of the mixtures. Conventional firing process was substituted by drying in a solar drying chamber. Nine mixtures were prepared using 62% excavation wastes, 4% wood cutting residues and 11%, 17% and 34% recycled aggregates. These mixtures were classified in two groups depending on their granulometry: the first one denominated cementitious recycled aggregates only having granulometry from 25.4 mm, 9.52 mm to 6.35 mm to fines and the second group denominated all in one recycled aggregates having granulometry of 6.35 mm to fines. The quality of the sustainable bricks was evaluated according to compressive strength and water absorption parameters. The results of nine mixtures showed that the reconstruction-bricks manufactured with the mixture seven consisting of 9.52 mm and 6.35 mm construction residues (all in one) fines presented the highest strength values, lowest maximum initial absorption (4 g/min) compared to the norm NMX-C-037-ONNCCE-2013 which establishes that the maximum limit for walls exposed to the outside is 5 g/min. Using a solar desiccator made from construction residues, the bricks were dried in 11 days, the maximum temperature was 76 °C and the maximum solar radiation captured was 733.4 W/m2.

The size of the irregular migrant population in the European Union – counting the uncountable?

PubMed

Vogel, Dita; Kovacheva, Vesela; Prescott, Hannah

2011-01-01

It is difficult to estimate the size of the irregular migrant population in a specific city or country, and even more difficult to arrive at estimates at the European level. A review of past attempts at European-level estimates reveals that they rely on rough and outdated rules-of-thumb. In this paper, we present our own European level estimates for 2002, 2005, and 2008. We aggregate country-specific information, aiming at approximate comparability by consistent use of minimum and maximum estimates and by adjusting for obvious differences in definition and timescale. While the aggregated estimates are not considered highly reliable, they do -- for the first time -- provide transparency. The provision of more systematic medium quality estimates is shown to be the most promising way for improvement. The presented estimate indicates a minimum of 1.9 million and a maximum of 3.8 million irregular foreign residents in the 27 member states of the European Union (2008). Unlike rules-of-thumb, the aggregated EU estimates indicate a decline in the number of irregular foreign residents between 2002 and 2008. This decline has been influenced by the EU enlargement and legalisation programmes.

Losses of Ammonia and Nitrate from Agriculture and Their Effect on Nitrogen Recovery in the European Union and the United States between 1900 and 2050.

PubMed

van Grinsven, Hans J M; Bouwman, Lex; Cassman, Kenneth G; van Es, Harold M; McCrackin, Michelle L; Beusen, Arthur H W

2015-03-01

Historical trends and levels of nitrogen (N) budgets and emissions to air and water in the European Union and the United States are markedly different. Agro-environmental policy approaches also differ, with emphasis on voluntary or incentive-based schemes in the United States versus a more regulatory approach in the European Union. This paper explores the implications of these differences for attaining long-term policy targets for air and water quality. Nutrient surplus problems were more severe in the European Union than in the United States during the 1970s and 1980s. The EU Nitrates and National Emission Ceilings directives contributed to decreases in fertilizer use, N surplus, and ammonia (NH) emissions, whereas in the United States they stabilized, although NH emissions are still increasing. These differences were analyzed using statistical data for 1900-2005 and the global IMAGE model. IMAGE could reproduce NH emissions and soil N surpluses at different scales (European Union and United States, country and state) and N loads in the Rhine and Mississippi. The regulation-driven changes during the past 25 yr in the European Union have reduced public concerns and have brought agricultural N loads to the aquatic environment closer to US levels. Despite differences in agro-environmental policies and agricultural structure (more N-fixing soybean and more spatially separated feed and livestock production in the United States than in the European Union), current N use efficiency in US and EU crop production is similar. IMAGE projections for the IAASTD-baseline scenario indicate that N loading to the environment in 2050 will be similar to current levels. In the United States, environmental N loads will remain substantially smaller than in the European Union, whereas agricultural production in 2050 in the United States will increase by 30% relative to 2005, as compared with an increase of 8% in the European Union. However, in the United States, even rigorous mitigation with maximum recycling of manure N and a 25% reduction in fertilizer use will not achieve the policy target to halve the N export to the Gulf of Mexico. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Recommended energy and nutrients intakes in the European Union: 2008-2016

PubMed

García Gabarra, Antoni; Castellà Soley, Marta; Calleja Fernández, Alicia

2017-03-30

The aim of this document is to refl ect the changes happened in the European Union legislation and the opinions of the European Food Safety Authority in relation to the nutritional labeling on food, the reference values for energy, macronutrients and micronutrients, and the tolerable upper safe levels. The European legislation in force uses the labeling reference values established by the Scientific Committee on Food in 2003. There would be advisable an update of them from the reference values for vitamins and minerals established by the European Food Safety Authority. Equally, there would be good to include reference labeling values for polyunsaturated fatty acids, dietary fiber and choline, and specific reference labeling values for children from 6 to 36 months. For vitamins and minerals there would be desirable the revision of tolerable upper safe levels and the establishment of maximum amounts allowed in fortified food and food supplements in the European Union; its absence might represent a risk in some population groups for an excessive and unsafe intake of certain minerals and vitamins.

Evaluation of pesticide residues in fruits and vegetables from Algeria.

PubMed

Mebdoua, Samira; Lazali, Mohamed; Ounane, Sidi Mohamed; Tellah, Sihem; Nabi, Fahima; Ounane, Ghania

2017-06-01

A total of 160 samples of 13 types of fresh fruits and vegetables from domestic production and import were analysed to detect the presence of pesticide residues. Analysis was performed by multi-residual extraction followed by gas chromatography-mass spectrometry. In 42.5% of the tested samples, no residues were found and 12.5% of samples contained pesticide residues above maximum residue limits. Risk assessment for long-term exposure was done for all pesticides detected in this study. Except chlorpyrifos and lambda-cyhalothrin, exposure to pesticides from vegetables and fruits was below 1% of the acceptable daily intake. Short-term exposure assessment revealed that in seven pesticide/commodity combinations, including three pesticides (chlorpyrifos, deltamethrin and lambda-cyhalothrin), the acute reference dose had been exceeded.

International Harmonization of Food Safety Assessment of Pesticide Residues.

PubMed

Ambrus, Árpád

2016-01-13

This paper summarizes the development of principles and methods applied within the program of the FAO/WHO Codex Alimentarius during the past 50 years for the safety assessment of pesticide residues in food and feed and establishing maximum residue limits (MRLs) to promote free international trade and assure the safety of consumers. The role of major international organizations in this process, the FAO capacity building activities, and some problematic areas that require special attention are briefly described.

Fate of vinclozolin, thiabendazole and dimethomorph during storage, handling and forcing of chicory.

PubMed

Spanoghe, Pieter; Ryckaert, Bert; Van Gheluwe, Cindy; Van Labeke, Marie-Christine

2010-02-01

As part of ongoing research for a sustainable production of Belgian endives, the fate of three fungicides during storage, handling and forcing of witloof chicory roots was investigated. Storage roots are protected against Sclerotinia sp. Fuckel and Phoma exigua var. exigua Desm. by means of vinclozolin and thiabendazole respectively. During hydroponic forcing, the most imminent pathogen is Phytophthora cryptogea Pethybr. & Laff., which is controlled by the use of dimethomorph. Vinclozolin and thiabendazole concentrations on roots remained constant during storage at -1 degrees C. Dermal exposure of the workers in hydroponics was exceeded. Vinclozolin and thiabendazole residues were not detected 2 weeks after hydroponic forcing; dimethomorph was still detected at harvest. At harvest, the vinclozolin concentration in the chicory heads was below the maximum residue limit, but the chicory roots contained residues much above the thiabendazole and dimethomorph maximum residue level. Vinclozolin and thiabendazole residues applied before storage are still present on the roots at the start of the forcing cycle. During the set-up of chicory roots, preventive measures are recommended, as effects of repeated human exposure to low doses of applied fungicides cannot be excluded. Dimethomorph applied at the start of the hydroponic forcing is the only pesticide detected in the drainage water at harvest. The chicory heads were safe for human consumption. However, more attention should be paid to the residues of fungicides in the roots used for cattle feeding.

Residual determination and risk assessment of buprofezin in plum (Prunus domestica) grown in open-field conditions following the application of three different formulations.

PubMed

Kabir, Md Humayun; Abd El-Aty, A M; Kim, Sung-Woo; Lee, Han Sol; Rahman, Md Musfiqur; Lee, Young-Jun; Chung, Hyung Suk; Lieu, Truong; Choi, Jeong-Heui; Shin, Ho-Chul; Im, Geon-Jae; Hong, Su Myeong; Shim, Jae-Han

2016-11-01

This study was conducted to characterize the residual level and perform a risk assessment on buprofezin formulated as an emulsifiable concentrate, wettable powder, and suspension concentrate over various treatment schedules in plum (Prunus domestica). The samples were extracted with an AOAC quick, easy, cheap, effective, rugged, and safe, 'QuEChERS', method after major modifications. As intrinsic interferences were observed in blank plum samples following dispersive-solid phase extraction (consisting of primary secondary amine and C 18 sorbents), amino cartridges were used for solid-phase extraction. Analysis was carried out using liquid chromatography with diode array detection and confirmed by liquid chromatography-tandem mass spectrometry. The method showed excellent linearity with determination coefficient (R 2  = 1) and satisfactory recoveries (at two spiking levels, 0.5 and 2.5 mg/kg) between 90.98 and 94.74% with relative standard deviation (RSD) ≤8%. The limit of quantification (0.05 mg/kg) was considerably lower than the maximum residue limit (2 mg/kg) set by the Codex Alimentarius. Absolute residue levels for emulsifiable concentrates were highest, perhaps owing to the dilution rate and adjuvant. Notably, all formulation residues were lower than the maximum residue limit, and safety data proved that the fruits are safe for consumers. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Crop residue is key for sustaining maximum food production and for conservation of our biosphere

USDA-ARS?s Scientific Manuscript database

Crop residue is key in our efforts to move towards agricultural sustainability. This paper provides a quick overview of some selected references and looks at some of the newest advances related to cover crops. Several authors have described in detail the benefits derived from improving soil quality ...

Three-dimensional local residual stress and orientation gradients near graphite nodules in ductile cast iron [3D local residual stress and orientation gradients near graphite nodules in ductile cast iron

DOE PAGES

Zhang, Y. B.; Andriollo, T.; Faester, S.; ...

2016-09-14

A synchrotron technique, differential aperture X-ray microscopy (DAXM), has been applied to characterize the microstructure and analyze the local mesoscale residual elastic strain fields around graphite nodules embedded in ferrite matrix grains in ductile cast iron. Compressive residual elastic strains are measured with a maximum strain of ~6.5–8 × 10 –4 near the graphite nodules extending into the matrix about 20 μm, where the elastic strain is near zero. The experimental data are compared with a strain gradient calculated by a finite element model, and good accord has been found but with a significant overprediction of the maximum strain. Thismore » is discussed in terms of stress relaxation during cooling or during storage by plastic deformation of the nodule, the matrix or both. Furthermore, relaxation by plastic deformation of the ferrite is demonstrated by the formation of low energy dislocation cell structure also quantified by the DAXM technique.« less

Effects of Storage of CPD-ADSOL Red Cells at 4C for as Long as 49 Days, Biochemical Modification, Freeze-Preservation, and Post-Wash Storage at 4C for 24 Hours

DTIC Science & Technology

1992-05-27

DPG, P50 levels , and the level of residual hemolysis were satisfactory. Our data show that 42-days is the maximum period that red blood cells can...survival value of only 61%, but ATP, DPG, P50 levels and the level of residual hemolysis were satisfactory. Our data show that 42-days is the maximum...collected red blood cells are stored at 4C for less than 2 weeks, the rejuventation process increases the red cell 2,3 DPG level to 250% of normal and the

Topographic enhancement of tidal motion in the western Barents Sea

NASA Technical Reports Server (NTRS)

Kowalik, Z.; Proshutinsky, A. YU.

1995-01-01

A high-resolution numerical lattice is used to study a topographically trapped motion around islands and shallow banks of the western Barents Sea caused both by the semidiurnal and diurnal tidal waves. Observations and model computations in the vicinity of Bear Island show well-developed trapped motion with distinctive tidal oscillatory motion. Numerical investigations demonstrate that one source of the trapped motion is tidal current rectification over shallow topgraphy. Tidal motion supports residual currents of the order of 8 cm/s around Bear Island and shallow Spitsbergenbanken. The structures of enhanced tidal currents for the semidiurnal components are generated in the shallow areas due to topographic amplification. In the diurnal band of oscillations the maximum current is associated with the shelf wave occurrence. Residual currents due to diurnal tides occur at both the shallow areas and the shelf slope in regions of maximum topographic gradients. Surface manifestation of the diurnal current enhancement is the local maximum of tidal amplitude at the shelf break of the order of 5 to 10 cm. Tidal current enhancement and tidally generated residual currents in the Bear Island and Spitsbergenabanken regions cause an increased generation of ice leads, ridges and, trapped motion of the ice floes.

Validation of the LacTek test applied to spiked extracts of tissue samples: determination of performance characteristics.

PubMed

Mitchell, J M; Yee, A J; McNab, W B; Griffiths, M W; McEwen, S A

1999-01-01

LacTek tests are competitive enzyme-linked immunosorbent assays intended for rapid detection of antimicrobial residues in bovine milk. In this study, the LacTek test protocol was modified for use with extracts of bovine tissue to detect beta-lactam, tetracycline, and sulfamethazine residues. Test performance characteristics--precision, accuracy, ruggedness, practicability, and analytical specificity and sensitivity--were investigated. Results suggest that LacTek tests can be easily adapted to detect antimicrobial residues in extracts of lean ground beef. However, positive samples may not contain residues at violative concentrations (i.e., Canadian maximum residue limits), and therefore, additional analysis would be required for final confirmation and quantitation (e.g., chromatography).

Plant protection product residues in white grapes and wines of "Malvasia Istriana" produced in Istria.

PubMed

Baša Česnik, Helena; Velikonja Bolta, Špela; Bavčar, Dejan; Radeka, Sanja; Lisjak, Klemen

2016-12-01

Monitorting of plant protection product residues was performed in 12 grape and 66 wine samples of "Malvasia Istriana" variety, produced in Istria winegrowing region of Croatia and Slovenia. The samples were analysed for the presence of 169 different active compounds using two multiresidual analytical methods: gas chromatography coupled with mass spectrometry and liquid chromatography coupled with tandem mass spectrometry. Residues were found in 58.3% of all the inspected grape samples and in 28.8% of all the inspected wine samples. Beside that contents of residues in grapes were below 10% of maximum residue level values and they should not represent any risk for "Malvasia Istriana" grape or wine consumers.

Greater Trochanteric Fixation Using a Cable System for Partial Hip Arthroplasty: A Clinical and Finite Element Analysis

PubMed Central

Ozan, Fırat; Koyuncu, Şemmi; Pekedis, Mahmut; Altay, Taşkın; Yıldız, Hasan; Toker, Gökhan

2014-01-01

The aim of the study was to investigate the efficacy of greater trochanteric fixation using a multifilament cable to ensure abductor lever arm continuity in patients with a proximal femoral fracture undergoing partial hip arthroplasty. Mean age of the patients (12 men, 20 women) was 84.12 years. Mean follow-up was 13.06 months. Fixation of the dislocated greater trochanter with or without a cable following load application was assessed by finite element analysis (FEA). Radiological evaluation was based on the distance between the fracture and the union site. Harris hip score was used to evaluate final results: outcomes were excellent in 7 patients (21.8%), good in 17 patients (53.1%), average in 5 patients (15.6%), and poor in 1 patient (9.3%). Mean abduction angle was 20.21°. Union was achieved in 14 patients (43.7%), fibrous union in 12 (37.5%), and no union in 6 (18.7%). FEA showed that the maximum total displacement of the greater trochanter decreased when the fractured bone was fixed with a cable. As the force applied to the cable increased, the displacement of the fractured trochanter decreased. This technique ensures continuity of the abductor lever arm in patients with a proximal femoral fracture who are undergoing partial hip arthroplasty surgery. PMID:25177703

Taylor spatial frame fixation in patients with multiple traumatic injuries: study of 57 long-bone fractures.

PubMed

Sala, Francesco; Elbatrawy, Yasser; Thabet, Ahmed M; Zayed, Mahmoud; Capitani, Dario

2013-08-01

To evaluate the Taylor spatial frame (TSF) for primary and definitive fixation of lower limb long-bone fractures in patients with multiple traumatic injuries. Retrospective. Level I trauma center. Consecutive series of 52 patients, 57 fractures (25 femoral and 32 tibial), treated between 2005 and 2009. Forty-nine fractures (86%) were open. Injury Severity Score ≥16 for all patients. Fifty-four fractures (95%) underwent definitive fixation with the TSF and 3 were treated primarily within 48 hours of injury. In 22 cases (39%), fractures were acutely reduced with the TSF, fixed to bone and the struts in sliding mode without further adjustment, and in 35 cases (61%), the total residual deformity correction program was undertaken. Clinical and radiological. Complete union was obtained in 52 fractures (91%) without additional surgery at an average of 29 weeks. Four nonunions and 1 delayed union occurred. Results based on Association for the Study and Application of the Method of Ilizarov criteria: 74% excellent, 16% good, 4% fair, and 7% poor for bone outcomes and 35% excellent, 47% good, and 18% fair for functional outcomes. Eighty-eight percent of patients returned to preinjury work activities. Primary and definitive fixation with the TSF is effective. Advantages include continuity of device until union, reduced risk of infection, early mobilization, restoration of primary defect caused by bone loss, easy and accurate application, convertibility and versatility compared with a monolateral fixator, and improved union rate and range of motion for lower extremity long-bone fractures in patients with multiple traumatic injuries.

Comparison of artificial maturation of lignite in hydrous and nonhydrous conditions

USGS Publications Warehouse

Behar, F.; Lewan, M.D.; Lorant, F.; Vandenbroucke, M.

2003-01-01

The objectives of the study are to compare product compositions and yields generated from lignite artificially matured by open nonhydrous pyrolysis, closed nonhydrous pyrolysis, and hydrous pyrolysis. The pyrolysis products were fractionated into CO2, H2O, CH4, C2-C5, C8-C14, C14+ saturates, C14+ aromatics and NSOs (resins+asphaltenes). All three methods generated high and similar quantities of water during pyrolysis that ranged between 14.6 and 15.2 wt.% of the original lignite. As a result of this high water content generated by the lignite, the experiments with no added water are referred to as nonhydrous rather than anhydrous. Rock-Eval pyrolysis and elemental analyses were conducted on the recovered lignite after solvent extraction to determine their residual hydrocarbon generation potential and to plot their position in a van Krevelen diagram, respectively. Residual lignite from the closed nonhydrous and hydrous experiments showed relationships between vitrinite reflectance (%Ro) values and atomic H/C ratios that occurred within the fields observed for natural maturation of coal. Although no significant differences in the atomic H/C ratios were observed between closed nonhydrous and hydrous pyrolysis, the vitrinite reflectance values were on the average 0.2% Ro lower in the residual lignite from the nonhydrous experiments. The remaining hydrocarbon generation potential as determined by Rock-Eval pyrolysis of the residual lignite showed that the nonhydrous residuals had on the average 16 mg more hydrocarbon potential per gram of original lignite than the hydrous residuals. This suggests there is a better release of the pyrolysis products from the lignite network in the hydrous experiments once generation occurs. For gas generation, at maximum yields, open nonhydrous pyrolysis generates the most hydrocarbon gas (21.0 mg/g original lignite), which is 20% more than closed nonhydrous pyrolysis and 29% more than hydrous pyrolysis. Closed nonhydrous pyrolysis generates on the average 14% more gas than hydrous pyrolysis, but the proportionality of the generated hydrocarbon gases is essentially the same for both pyrolysis methods. At maximum yields, CO2 generation is greatest in hydrous pyrolysis (99.5 mg/g original lignite), with yields being 37 percent higher than closed nonhydrous pyrolysis and 26% higher than open nonhydrous pyrolysis. The maximum yields of C14+ products are highest and similar for open nonhydrous pyrolysis and hydrous pyrolysis (125.6 and 125.9 mg/g lignite, respectively), and are more than 70% higher than closed nonhydrous pyrolysis. This difference in the maximum yields of C14+ products can be explained by differences in the proportionality between either cracking reactions that result in liquid product and char formation or trapping of generated products within the coal network (cross-linking reactions). Maximum yields of C14+ aliphatics from hydrous experiments may not have been attained, but the maximums that were observed and their GC traces are similar for the three pyrolysis systems.

Stochastic modelling of the monthly average maximum and minimum temperature patterns in India 1981-2015

NASA Astrophysics Data System (ADS)

Narasimha Murthy, K. V.; Saravana, R.; Vijaya Kumar, K.

2018-04-01

The paper investigates the stochastic modelling and forecasting of monthly average maximum and minimum temperature patterns through suitable seasonal auto regressive integrated moving average (SARIMA) model for the period 1981-2015 in India. The variations and distributions of monthly maximum and minimum temperatures are analyzed through Box plots and cumulative distribution functions. The time series plot indicates that the maximum temperature series contain sharp peaks in almost all the years, while it is not true for the minimum temperature series, so both the series are modelled separately. The possible SARIMA model has been chosen based on observing autocorrelation function (ACF), partial autocorrelation function (PACF), and inverse autocorrelation function (IACF) of the logarithmic transformed temperature series. The SARIMA (1, 0, 0) × (0, 1, 1)12 model is selected for monthly average maximum and minimum temperature series based on minimum Bayesian information criteria. The model parameters are obtained using maximum-likelihood method with the help of standard error of residuals. The adequacy of the selected model is determined using correlation diagnostic checking through ACF, PACF, IACF, and p values of Ljung-Box test statistic of residuals and using normal diagnostic checking through the kernel and normal density curves of histogram and Q-Q plot. Finally, the forecasting of monthly maximum and minimum temperature patterns of India for the next 3 years has been noticed with the help of selected model.

12 CFR 713.6 - What is the permissible deductible?

Code of Federal Regulations, 2013 CFR

2013-01-01

... assets up to a maximum of $200,000; for credit unions that have received a composite CAMEL rating of “1... received a composite CAMEL rating of “1” or “2” for the last two (2) full examinations and maintained a net... paragraph or fails to meet the CAMEL rating requirements of this paragraph as determined by its most recent...

12 CFR 713.6 - What is the permissible deductible?

Code of Federal Regulations, 2014 CFR

2014-01-01

... assets up to a maximum of $200,000; for credit unions that have received a composite CAMEL rating of “1... received a composite CAMEL rating of “1” or “2” for the last two (2) full examinations and maintained a net... paragraph or fails to meet the CAMEL rating requirements of this paragraph as determined by its most recent...

Monitoring of pesticide residues of five notable vegetables at Agbogbloshie market in Accra, Ghana.

PubMed

Osei-Fosu, P; Donkor, A K; Nyarko, S; Nazzah, N K; Asante, I K; Kingsford-Adabo, R; Arkorful, N A

2014-11-01

The study monitored the concentrations of pesticide residues in vegetables arriving at Agbogbloshie, a central market in the Accra Metropolis from different parts of Ghana and beyond. A total of 810 samples of 5 different vegetables from Central, Volta, Greater Accra, Ashanti, Eastern Regions, and neighboring country (Togo) were collected from January 2009 through to December 2011. In all, 18 % of the samples had no detectable residues, 62 % were below the maximum residue limits (MRLs), and 20 % also exceeded the EU (MRLs) adopted values. Overall, lettuce contained the highest number of residues above their MRLs besides cucumber and cabbage. The pesticide residues were mainly organophosphates and synthetic pyrethroids. The results demonstrate the need for continuous monitoring of pesticide residues in vegetables arriving at the various major markets in Ghana.

Leaching of Clothianidin in Two Different Indian Soils: Effect of Organic Amendment.

PubMed

Singh, Ningthoujam Samarendra; Mukherjee, Irani; Das, Shaon Kumar; Varghese, E

2018-04-01

Clothianidin is a widely used insecticide under Indian subtropical condition. The objective of this study was to generate residue data which aims to understand leaching potential of clothianidin [(E)-1-(2-chloro-1,3-thiazol-5-ylmethyl)-3-methyl-2- nitroguanidine] through packed soil column. The maximum amount of clothianidin was recovered at 0-5 cm soil depth in both Manipur (67.15%) and Delhi soil (52.0%) under continuous flow condition. Manipur and Delhi soil concentrated maximum residue with or without farm yard manure (FYM) in 0-20 cm soil depth. The effect of varying the amount of water enhanced the distribution of residues in the first 0-5 cm layer. Among the tested soils, residue was detected in the leachate from Delhi soil (0.04 µg/mL). Clothianidin leaching was minimized in soil of Manipur compared to Delhi after incorporation of FYM. As the volume of water increased upto 160 mL, mobility increased and residues moved to lower depth. Clothianidin did not leach out of the 25 cm long soil columns even after percolating water equivalent to 415.42 mm rainfall. Clothianidin is mobile in soil system and mobility can be reduced by organic amendment application.

Numerical Analysis of Residual Stress and Distortion Use Finite Element Method on Inner Bottom Construction of Geomarin IV Survey Ship with Welding Sequence Variations

NASA Astrophysics Data System (ADS)

Syahroni, N.; Hartono, A. B. W.; Murtedjo, M.

2018-03-01

In the ship fabrication industry, welding is the most critical stage. If the quality of welding on ship fabrication is not good, then it will affect the strength and overall appearance of the structure. One of the factors that affect the quality of welding is residual stress and distortion. In this research welding simulation is performed on the inner bottom construction of Geomarin IV Ship Survey using shell element and has variation to welding sequence. In this study, welding simulations produced peak temperatures at 2490 K at variation 4. While the lowest peak temperature was produced by variation 2 with a temperature of 2339 K. After welding simulation, it continued simulating residual stresses and distortion. The smallest maximum tensile residual stress found in the inner bottom construction is 375.23 MPa, and the maximum tensile pressure is -20.18 MPa. The residual stress is obtained from variation 3. The distortion occurring in the inner bottom construction for X=720 mm is 4.2 mm and for X=-720 mm, the distortion is 4.92 mm. The distortion is obtained from the variation 3. Near the welding area, distortion value reaches its minimum point. This is because the stiffeners in the form of frames serves as anchoring.

Bioefficacy, dissipation kinetics and safety evaluation of selected insecticides in Allium cepa L.

PubMed

Srinivas P, Satya; Banerjee, Kaushik; Jadhav, Manjusha R; Ghaste, Manoj S; Lawande, K E

2012-01-01

This paper reports the bioefficacy of selected insecticides against thrips and their pre-harvest intervals (PHI) in onion pertaining to their recommended application rates and maximum residue limits. Profenophos, methomyl and imidacloprid showed comparatively higher bioefficacy against thrips. GC-MS and LC-MS/MS-based residue analysis methods in onion bulbs and composite matrix of bulbs+leaves were thoroughly validated. The residue data for bulb+leaves was assessed with reference to the EU-MRLs applicable for spring onion. Dimethoate was the most stable chemical with PHI of 52.5 days, followed by monocrotophos (24 days) and carbofuran (20.5 days). The PHIs of profenophos, chlorpyrifos, methomyl and cypermethrin were similar and within the range of 10-13 days. Imidacloprid and λ-cyhalothrin had similar PHI of 4.5 days. Spinosad was the fastest-degrading chemical with PHI of 2 days. The combined bioefficacy and residue dynamics information will support label-claim of these insecticides for the management of thrips in onion, help in scheduling their applications in pest management program as per relative PHIs and minimize the residue accumulations at harvest. The dietary exposure was less than the maximum permissible intake for most of the insecticides on all sampling days except for dimethoate and monocrotophos.

Transfer of ipsilateral fibula on vascular pedicle for treatment of congenital pseudarthrosis of the tibia.

PubMed

Tan, Jane S; Roach, James W; Wang, Angela A

2011-01-01

Although the use of free vascularized fibula grafts has frequently been reported in the treatment of congenital pseudarthrosis of the tibia, the use of ipsilateral fibula graft on a vascular pedicle is uncommon. We reviewed the long-term results of this procedure in 11 patients. The records of 11 patients who underwent transfer of the ipsilateral fibula on a vascular pedicle between 2.1 and 10.8 years of age were retrospectively reviewed. Average follow-up was 11 years after the index procedure. Seven patients had reached skeletal maturity. Clinical records and radiographs were reviewed to determine patient demographics, surgical parameters, union rate, refracture rate, residual deformity, and functional outcome. Eight patients (73%) achieved union at an average of 20.1 months. Additional bone grafting procedures were required in 4 patients with distal nonunions. There were 3 refractures (38%). Four patients eventually underwent amputation, and 1 patient had a persistent nonunion at final follow-up. Residual deformity included tibial valgus and procurvatum deformities, limb length discrepancy, and ankle valgus. Use of the ipsilateral fibula did not seem to increase the risk of ankle valgus. Functional outcomes were good in all but one patient. Use of the ipsilateral fibula as a pedicle graft provides reasonable results in healing congenital pseudarthrosis of the tibia. Patients should be monitored for the sequelae of this condition, including nonunion, refracture, shortening, and angular deformity, and treated accordingly. Therapeutic Level IV.

Dissipation of chlorantraniliprole in tomato fruits and soil.

PubMed

Malhat, Farag; Abdallah, Hend; Hegazy, Islam

2012-03-01

The main objective of this study was to understand the residue and persistence behaviour of new insecticide chlorantraniliprole in tomato fruit and soil samples. Its residue was analyzed by HPLC and it dissipated in tomato fruit and soil following first order kinetics. The results showed half life (t(1/2)) value of 3.30 and 3.66 days for chlorantraniliprole in tomato fruit and soil, respectively. According to maximum residue limit (MRL) the pre-harvest interval (PHI) of chlorantraniliprole on tomato was 8-days after the treatment.

Depletion of penicillin G residues in heavy sows after intramuscular injection. Part I: Tissue residue depletion

USDA-ARS?s Scientific Manuscript database

Heavy sows (n=126) were treated with penicillin G procaine at a 5x label dose (33,000 IU/kg) for 3 consecutive days by intramuscular (IM) injection using 3 separate patterns (treatments) of drug administration (42 sows per treatment). Treatments differed by pattern and maximum injection volume per s...

Monitoring and determination of sulfonamide antibiotics (sulfamethoxydiazine, sulfamethazine, sulfamethoxazole and sulfadiazine) in imported Pangasius catfish products in Thailand using liquid chromatography coupled with tandem mass spectrometry.

PubMed

Jansomboon, Worawat; Boontanon, Suwanna Kitpati; Boontanon, Narin; Polprasert, Chongrak; Thi Da, Chau

2016-12-01

This research aimed to monitor the concentrations of sulfamethoxydiazine (SMD), sulfamethazine (SMT), sulfamethoxazole (SMX) and sulfadiazine (SDZ) in imported Pangasius catfish products in Thailand. The residues of the four sulfonamides (SAs) were analyzed by extraction process and liquid chromatography coupled with tandem mass spectrometry. The highest concentrations found were 10.97ng/g for SMD, 6.23ng/g for SMT, 11.13ng/g for SDZ and 245.91ng/g for SMX, which was higher than the European Union (EU) standard (100ng/g). Moreover, all samples contaminated with SMX also contained SMT, indicating that more than one antibiotic was used for production in the country of origin. Because Thai standards for antibiotics in food have not been completely set, all contaminated discovered would not be considered to be an illegal food, in which antibiotic residues may affect human health in the long term. Therefore, antibiotic residues in Pangasius catfish products should be continually regulated and monitored. Copyright © 2016 Elsevier Ltd. All rights reserved.

New magnetic graphene-based inorganic-organic sol-gel hybrid nanocomposite for simultaneous analysis of polar and non-polar organophosphorus pesticides from water samples using solid-phase extraction.

PubMed

Rashidi Nodeh, Hamid; Wan Ibrahim, Wan Aini; Kamboh, Muhammad Afzal; Sanagi, Mohd Marsin

2017-01-01

A new graphene-based tetraethoxysilane-methyltrimethoxysilane sol-gel hybrid magnetic nanocomposite (Fe 3 O 4 @G-TEOS-MTMOS) was synthesised, characterized and successfully applied in magnetic solid-phase extraction (MSPE) for simultaneous analysis of polar and non-polar organophosphorus pesticides from several water samples. The Fe 3 O 4 @G-TEOS-MTMOS nanocomposite was characterized using Fourier transform-infrared spectroscopy, energy-dispersive X-ray spectroscopy, field emission scanning electron microscopy and X-ray diffraction. Separation, determination and quantification were achieved using gas chromatography coupled with micro electron capture detector. Adsorption capacity of the sorbent was calculated using Langmuir equation. MSPE was linear in the range 100-1000 pg mL -1 for phosphamidon and dimethoate, and 10-100 pg mL -1 for chlorpyrifos and diazinon, with limit of detection (S/N = 3) of 19.8, 23.7, 1.4 and 2.9 pg mL -1 for phosphamidon, dimethoate, diazinon and chlorpyrifos, respectively. The LODs obtained is well below the maximum residual level (100 pg mL -1 ) as set by European Union for pesticides in drinking water. Acceptable precision (%RSD) was achieved for intra-day (1.3-8.7%, n = 3) and inter-day (7.6-17.8%, n = 15) analyses. Fe 3 O 4 @G-TEOS-MTMOS showed high adsorption capacity (54.4-76.3 mg g -1 ) for the selected OPPs. No pesticide residues were detected in the water samples analysed. Excellent extraction recoveries (83-105%) were obtained for the spiked OPPs from tap, river, lake and sea water samples. The newly synthesised Fe 3 O 4 @G-TEOS-MTMOS showed high potential as adsorbent for OPPs analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of two extraction methods for the determination of 135 pesticides in Corydalis Rhizoma, Chuanxiong Rhizoma and Angelicae Sinensis Radix by liquid chromatography-triple quadrupole-mass spectrometry. Application to the roots and rhizomes of Chinese herbal medicines.

PubMed

Liu, Jie; Tong, Ling; Li, Dongxiang; Meng, Wenting; Sun, Wanyang; Zhao, Yunli; Yu, Zhiguo

2016-04-01

In this study, two simple pretreatment methods were comprehensively evaluated for the determination of 135 pesticide residues in roots and rhizomes of Chinese herbal medicines (CHMs). The studied methodologies are (a) solid-phase extraction (SPE) and (b) Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS). For SPE, extraction solvents, SPE cartridges and types and volume of eluent were accessed and optimized. For QuEChERS, different versions, acetic acid concentration and dispersive solid-phase extraction (dSPE) sorbent materials were tested. SPE and QuEChERS were estimated in recovery range, the number of pesticides that were recovered ranging from 90% to 110% and expenses in Corydalis Rhizoma, Chuanxiong Rhizoma and Angelicae Sinensis Radix. QuEChERS method showed better performance than SPE. The method showed good linearity over the range assayed 0.9986-0.9999 (1-80ng/mL for 124 pesticides, 1-50ng/mL for 10 pesticides, 1-20ng/mL for satisfar). The matrix effect was compensated by matrix-based calibration curves with internal standard. The average recoveries of all pesticides were ranging from 70% to 120% at three levels of 10, 50 and 100ng/g with relative standard deviations less than 20%. The limits of quantification of the 135 pesticides in three matrices were 1-5ng/g, which were below the maximum residue levels (MRLs) established by the European Union. The verified QuEChERS method was successfully applied to the analysis of 65 actual samples from eight different types of roots and rhizomes of CHMs. Angelicae Sinensis Radix was the most susceptible to pesticides among these samples, and the most frequently detected pesticide was carbendazim with levels below MRLs. Metalaxyl, phorate, atrazine, diniconazole, coumaphos and paclobutrazol were also detected in some samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Biomass for energy in the European Union - a review of bioenergy resource assessments

PubMed Central

2012-01-01

This paper reviews recent literature on bioenergy potentials in conjunction with available biomass conversion technologies. The geographical scope is the European Union, which has set a course for long term development of its energy supply from the current dependence on fossil resources to a dominance of renewable resources. A cornerstone in European energy policies and strategies is biomass and bioenergy. The annual demand for biomass for energy is estimated to increase from the current level of 5.7 EJ to 10.0 EJ in 2020. Assessments of bioenergy potentials vary substantially due to methodological inconsistency and assumptions applied by individual authors. Forest biomass, agricultural residues and energy crops constitute the three major sources of biomass for energy, with the latter probably developing into the most important source over the 21st century. Land use and the changes thereof is a key issue in sustainable bioenergy production as land availability is an ultimately limiting factor. PMID:22546368

Assessing item fit for unidimensional item response theory models using residuals from estimated item response functions.

PubMed

Haberman, Shelby J; Sinharay, Sandip; Chon, Kyong Hee

2013-07-01

Residual analysis (e.g. Hambleton & Swaminathan, Item response theory: principles and applications, Kluwer Academic, Boston, 1985; Hambleton, Swaminathan, & Rogers, Fundamentals of item response theory, Sage, Newbury Park, 1991) is a popular method to assess fit of item response theory (IRT) models. We suggest a form of residual analysis that may be applied to assess item fit for unidimensional IRT models. The residual analysis consists of a comparison of the maximum-likelihood estimate of the item characteristic curve with an alternative ratio estimate of the item characteristic curve. The large sample distribution of the residual is proved to be standardized normal when the IRT model fits the data. We compare the performance of our suggested residual to the standardized residual of Hambleton et al. (Fundamentals of item response theory, Sage, Newbury Park, 1991) in a detailed simulation study. We then calculate our suggested residuals using data from an operational test. The residuals appear to be useful in assessing the item fit for unidimensional IRT models.

Determination of the residue levels of nicarbazin and combination nicarbazin-narasin in broiler chickens after oral administration

PubMed Central

da Silva, Guilherme Resende; de Assis, Débora Cristina Sampaio; Cançado, Silvana de Vasconcelos

2017-01-01

The depletion times of the anticoccidial nicarbazin administered individually and of nicarbazin and narasin administered in combination were evaluated by determining the presence and levels of 4,4'-dinitrocarbanilide (DNC), the marker residue for nicarbazin, and narasin residues in the muscle tissues of broiler chickens subjected to a pharmacological treatment. A high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) method was used. The results showed the presence of all anticoccidial residues; however, the DNC levels were higher when the nicarbazin was administered individually than when it was used in association with narasin throughout the experimental period. After six days of withdrawal, the DNC level following nicarbazin administration alone was lower than the maximum residue level (MRL) of 200 μg kg-1. However, when the nicarbazin was co-administered with narasin, the concentrations of DNC were lower than the MRL after four days of withdrawal. These results may be justified because the dosage of nicarbazin, when administrated individually, is greater than when it is used in combination with narasin. The levels of narasin were lower than the MRL of 15 μg kg-1 throughout the evaluation period. It was concluded that nicarbazin is rapidly metabolized from the broiler muscles up to six days of withdrawal since the DNC levels were lower than the maximum residue level (MRL) and the concentrations of narasin were lower than the MRL throughout the evaluation period. PMID:28750013

Effect of in-season creatine supplementation on body composition and performance in rugby union football players.

PubMed

Chilibeck, Philip D; Magnus, Charlene; Anderson, Matthew

2007-12-01

Rugby union football requires muscular strength and endurance, as well as aerobic endurance. Creatine supplementation may enhance muscular performance, but it is unclear if it would interfere with aerobic endurance during running because of increased body mass. The purpose of this study was to determine if creatine supplementation during 8 weeks of a season of rugby union football can increase muscular performance, without negatively affecting aerobic endurance. Rugby union football players were randomized to receive 0.1 g.kg(-1).d(-1) creatine monohydrate (n=9) or placebo (n=9) during 8 weeks of the rugby season. Players practiced twice per week for approximately 2 h per session and played one 80 min game per week. Before and after the 8 weeks, players were measured for body composition (air displacement plethysmography), muscular endurance (number of repetitions at 75% of one repetition maximum (1 RM) for bench press and leg press), and aerobic endurance (Leger shuttle-run test with 1 min stages of progressively increasing speed). There were time main effects for body mass (-0.7+/-0.4 kg; p=0.05), fat mass (-1.9+/-0.8 kg; p<0.05), and a trend for an increase in lean tissue mass (+1.2+/-0.5 kg; p=0.07), with no differences between groups. The group receiving creatine supplementation had a greater increase in the number of repetitions for combined bench press and leg press tests compared with the placebo group (+5.8+/-1.4 vs. +0.9+/-2.0 repetitions; p<0.05). There were no changes in either group for aerobic endurance. Creatine supplementation during a rugby union football season is effective for increasing muscular endurance, but has no effect on body composition or aerobic endurance.

Azinphos-methyl residues in apples and spatial distribution of fluorescein in vase-shaped apple trees.

PubMed

Bélanger, A; Bostanian, N J; Boivin, G; Boudreau, F

1991-06-01

Vase-shaped standard apple trees cv. McIntosh were sprayed with azinphos-methyl at pink, pink and 1st cover and 1st cover only. Residue analyses by gas chromatography revealed detectable residues on foliage until mid summer. At harvest, negligible residue levels were found on the peel and the whole apple. On four trees, fluorescein was sprayed in the same manner as the insecticide and maximum levels of the dye were detected on the outside lower canopy along the row. Minimal concentration of fluorescein was detected on the inner upper canopy away from the direction of the row.

In-situ measurements of velocity structure within turbidity currents

USGS Publications Warehouse

Xu, J. P.; Noble, M.A.; Rosenfeld, L.K.

2004-01-01

Turbidity currents are thought to be the main mechanism to move ???500,000 m3 of sediments annually from the head of the Monterey Submarine Canyon to the deep-sea fan. Indirect evidence has shown frequent occurrences of such turbidity currents in the canyon, but the dynamic properties of the turbidity currents such as maximum speed, duration, and dimensions are still unknown. Here we present the first-ever in-situ measurements of velocity profiles of four turbidity currents whose maximum along-canyon velocity reached 190 cm/s. Two turbidity currents coincided with storms that produced the highest swells and the biggest stream flows during the year-long deployment. Copyright 2004 by the American Geophysical Union.

Creation of residual flows in a partially stratified estuary

USGS Publications Warehouse

Stacey, M.T.; Burau, J.R.; Monismith, Stephen G.

2001-01-01

The creation of residual flows in estuaries is examined using acoustic Doppler current profiler data sets from northern San Francisco Bay. The data sets are analyzed using principal component analysis to examine the temporal variability of the flows which create the residual circulation. It is seen that in this periodically and partially stratified estuary the residual flows are created through a series of pulses with strong variability at the 24-hour timescale, through the interaction of shear, stratification and mixing. This interaction is captured through the use of a dimensionless number, the horizontal Richardson number (Rix), which is developed to examine the local balance between the stratifying and destratifying forces at the tidal timescale. It is seen that Rix is a valuable parameter in predicting the onset of the residual-creating events, with a threshold value of ??? 3 on ebb tides. This critical value is argued to be a threshold, above which the stratification and shear flow create a feedback effect, each further intensifying the other. This feedback results in a highly variable exchange flow which creates the estuarine residual in intermittent pulses rather than as a steady flow. Although typically attributed to baroclinic forcing, an argument is made that these pulses of residual-creating exchange flow could be created by barotropic forcing in the presence of variable stratification which is asymmetric between flood and ebb tides. This result poses a great challenge for turbulence modeling, as the timing and magnitude of stratification and shear must be correctly simulated on the tidal timescale in order to reproduce the effects seen in the data sets presented. Copyright 2001 by the American Geophysical Union.

Captan and fenitrothion dissipation in field-treated cauliflowers and effect of household processing.

PubMed

Fernández-Cruz, María L; Barreda, Mercedes; Villarroya, Mercedes; Peruga, Arantzazu; Llanos, Susana; García-Baudín, José M

2006-07-01

Field trial studies have been performed with captan and fenitrothion on cauliflower to propose maximum residue limits and to study the dissipation of the pesticides. Residue levels have been determined at different times following good laboratory practice using gas chromatography with mass spectrometric detection. The behaviour of residue levels of these compounds after household processing has been analysed using gas chromatography with electron capture detection. Seven days after treatment, residue levels of captan could be detected, but not of fenitrothion. The half-lives of dissipation for captan and fenitrothion were calculated as 0.9 and 1.8 days respectively. Washing did not significantly affect the residual amounts of captan and fenitrothion observed in raw vegetables; however, after cooking, captan had degraded completely, whereas residue levels of fenitrothion were not modified significantly.

Acephate and buprofezin residues in olives and olive oil.

PubMed

Cabras, P; Angioni, A; Garau, V L; Pirisi, F M; Cabitza, F; Pala, M

2000-10-01

Field trials were carried out to study the persistence of acephate and buprofezin on olives. Two cultivars, pizz'e carroga and pendolino, with very large and small fruits respectively were used. After treatment, no difference was found between the two pesticide deposits on the olives. The disappearance rates, calculated as pseudo first order kinetics, were similar for both pesticides (on average 12 days). Methamidophos, the acephate metabolite, was always present on all olives, and in some pendolino samples it showed higher residues than the maximum residue limit (MRL). During washing, the first step of olive processing, the residue level of both pesticides on the olives did not decrease. After processing of the olives into oil, no residues of acephate or methamidophos were found in the olive oil, while the residues of buprofezin were on average four times higher than on olives.

Pesticide residues in raspberries (Rubus idaeus L.) and dietary risk assessment.

PubMed

Łozowicka, B; Kaczyński, P; Jankowska, M; Rutkowska, E; Hrynko, I

2012-01-01

The aim of this study was to evaluate the residues of 140 pesticides in raspberries from north-eastern Poland (2005-2010). Gas chromatography with electron capture detector (GC-ECD) and nitrogen phosphorous detector (GC-NPD) was used. Among the 128 samples, 66 (51.6%) were found to detect residues: 14.1% contained one pesticide and around 38% multiple pesticide residues. The most frequently detected were pyrimethanil residues (36.0%). Twenty-seven (21.1%) raspberry samples exceeded the maximum residue limits. The estimated daily intakes ranged from 0.003% to 3.183% of the acceptable daily intake (ADI) for adults 0.008% and 9.7% for toddlers, respectively. The most critical case is procymidone, the acute risk was 180.9% of acute reference dose (ARfD) for toddlers and for adults (83% of ARfD) which is high.

Physiological demands of women's rugby union: time-motion analysis and heart rate response.

PubMed

Virr, Jody Lynn; Game, Alex; Bell, Gordon John; Syrotuik, Daniel

2014-01-01

The aim of this study was to determine the physical demands of women's rugby union match play using time-motion analysis and heart rate (HR) response. Thirty-eight premier club level female rugby players, ages 18-34 years were videotaped and HRs monitored for a full match. Performances were coded into 12 different movement categories: 5 speeds of locomotion (standing, walking, jogging, striding, sprinting), 4 forms of intensive non-running exertion (ruck/maul/tackle, pack down, scrum, lift) and 3 discrete activities (kick, jump, open field tackle). The main results revealed that backs spend significantly more time sprinting and walking whereas forwards spend more time in intensive non-running exertion and jogging. Forwards also had a significantly higher total work frequency compared to the backs, but a higher total rest frequency compared to the backs. In terms of HR responses, forwards displayed higher mean HRs throughout the match and more time above 80% of their maximum HR than backs. In summary, women's rugby union is characterised by intermittent bursts of high-intensity activity, where forwards and backs have similar anaerobic energy demands, but different specific match demands.

Differences and similarities in fatigue behaviour and its influences on critical current and residual strength between Ti-Nb and Nb3Al superconducting composite wires

NASA Astrophysics Data System (ADS)

Ochiai, Shojiro; Oki, Yuichiro; Sekino, Fumiaki; Ohno, Hiroaki; Hojo, Masaki; Moriai, Hidezumi; Sakai, Shuji; Koganeya, Masanobu; Hayashi, Kazuhiko; Yamada, Yuichi; Ayai, Naoki; Watanabe, Kazuo

2000-04-01

The influences of fatigue damage introduced at room temperature on critical current at 4.2 K and residual strength at room temperature of Ti-Nb superconducting composite wire with a low copper ratio (1.04) were studied. The experimental results were compared with those of Nb3 Al composite. The following differences between the composites were found: the fracture surface of the Ti-Nb filaments in the composite varies from a ductile pattern under static loading to a brittle one under cyclic loading, while the Nb3 Al compound always shows a brittle pattern under both loadings; the fracture strength of the Ti-Nb composite is given by the net stress criterion but that of Nb3 Al by the stress intensity factor criterion; in the Ti-Nb composite the critical current Ic decreases with increasing number of stress cycles simultaneously with the residual strength icons/Journals/Common/sigma" ALT="sigma" ALIGN="TOP"/> c ,r , while in the Nb3 Al composite Ic decreases later than icons/Journals/Common/sigma" ALT="sigma" ALIGN="TOP"/> c ,r . On the other hand, both composites have the following similarities: the filaments are fractured due to the propagation of the fatigue crack nucleated in the copper; with increasing number of stress cycles, the damage progresses in the order of stage I (formation of cracks in the clad copper), stage II (stable propagation of the fatigue crack into the inner core) and stage III (overall fracture), among which stage II occurs in the late stage beyond 85 to 90% of the fatigue life; at intermediate maximum stress, many large cracks grow into the core portion at different cross sections but not at high and low maximum stresses; accordingly, the critical current and residual strength of the portion apart from the main crack are low for the intermediate maximum stress but not for low and high maximum stresses.

Different inhibitory potency of febuxostat towards mammalian and bacterial xanthine oxidoreductases: insight from molecular dynamics

PubMed Central

Kikuchi, Hiroto; Fujisaki, Hiroshi; Furuta, Tadaomi; Okamoto, Ken; Leimkühler, Silke; Nishino, Takeshi

2012-01-01

Febuxostat, a drug recently approved in the US, European Union and Japan for treatment of gout, inhibits xanthine oxidoreductase (XOR)-mediated generation of uric acid during purine catabolism. It inhibits bovine milk XOR with a Ki in the picomolar-order, but we found that it is a much weaker inhibitor of Rhodobacter capsulatus XOR, even though the substrate-binding pockets of mammalian and bacterial XOR are well-conserved as regards to catalytically important residues and three-dimensional structure, and both permit the inhibitor to be accommodated in the active site, as indicated by computational docking studies. To clarify the reason for the difference of inhibitory potency towards the two XORs, we performed molecular dynamics simulations. The results indicate that differences in mobility of hydrophobic residues that do not directly interact with the substrate account for the difference in inhibitory potency. PMID:22448318

Voluntary Control of Residual Antagonistic Muscles in Transtibial Amputees: Feedforward Ballistic Contractions and Implications for Direct Neural Control of Powered Lower Limb Prostheses.

PubMed

Huang, Stephanie; Huang, He

2018-04-01

Discrete, rapid (i.e., ballistic like) muscle activation patterns have been observed in ankle muscles (i.e., plantar flexors and dorsiflexors) of able-bodied individuals during voluntary posture control. This observation motivated us to investigate whether transtibial amputees are capable of generating such a ballistic-like activation pattern accurately using their residual ankle muscles in order to assess whether the volitional postural control of a powered ankle prosthesis using proportional myoelectric control via residual muscles could be feasible. In this paper, we asked ten transtibial amputees to generate ballistic-like activation patterns using their residual lateral gastrocnemius and residual tibialis anterior to control a computer cursor via proportional myoelectric control to hit targets positioned at 20% and 40% of maximum voluntary contraction of the corresponding residual muscle. During practice conditions, we asked amputees to hit a single target repeatedly. During testing conditions, we asked amputees to hit a random sequence of targets. We compared movement time to target and end-point accuracy. We also examined motor recruitment synchronization via time-frequency representations of residual muscle activation. The result showed that median end-point error ranged from -0.6% to 1% maximum voluntary contraction across subjects during practice, which was significantly lower compared to testing ( ). Average movement time for all amputees was 242 ms during practice and 272 ms during testing. Motor recruitment synchronization varied across subjects, and amputees with the highest synchronization achieved the fastest movement times. End-point accuracy was independent of movement time. Results suggest that it is feasible for transtibial amputees to generate ballistic control signals using their residual muscles. Future work on volitional control of powered power ankle prostheses might consider anticipatory postural control based on ballistic-like residual muscle activation patterns and direct continuous proportional myoelectric control.

Combined micromechanical and fabrication process optimization for metal-matrix composites

NASA Technical Reports Server (NTRS)

Morel, M.; Saravanos, D. A.; Chamis, C. C.

1991-01-01

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Concurrent micromechanical tailoring and fabrication process optimization for metal-matrix composites

NASA Technical Reports Server (NTRS)

Morel, M.; Saravanos, D. A.; Chamis, Christos C.

1990-01-01

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Residual Stress Distribution and Microstructure of a Multiple Laser-Peened Near-Alpha Titanium Alloy

NASA Astrophysics Data System (ADS)

Umapathi, A.; Swaroop, S.

2018-04-01

Laser peening without coating (LPwC) was performed on a Ti-2.5 Cu alloy with multiple passes (1, 3 and 5), using a Nd:YAG laser (1064 nm) at a constant overlap rate of 70% and power density of 6.7 GW cm-2. Hardness and residual stress profiles indicated thermal softening near the surface (< 100 μm) and bulk softening due to adiabatic heating. Maximum hardness (235 HV at 500 μm) and maximum residual stress (- 890 MPa at 100 μm) were observed for LPwC with 1 pass. Surface roughness and surface 3-D topography imaging showed that the surface roughness increased with the increase in the number of passes. XRD results indicated no significant β phases. However, peak shifts, broadening and asymmetry were observed and interpreted based on dislocation activity. Microstructures indicated no melting or resolidification or refinement of grains at the surface. Twin density was found to increase with the increase in the number of passes.

Ivermectin residues in squab.

PubMed

Bennett, D C; Cheng, K M

2012-11-01

No drugs have been approved for the treatment of parasitic nematodes in pigeons, but ivermectin, a broad-spectrum endectocide, has been used extra-label by prescription. Producers currently allow for a 2-wk withdrawal time before marketing squabs. However, because its use is extra-label there is no legal maximum residue limit for ivermectin in squab meat. The purpose of this study was to examine the depletion of ivermectin (passed by the parents to the squabs) from the tissues of squab. Adult pigeons brooding squab were treated with ivermectin in their drinking water (3.3 µg/mL) for 3 d. After dosing the parents, the ivermectin concentration of the breast meat and liver of squabs was found to be greater than the maximum residual limits established for livestock, indicating that ivermectin was transferred from the parents to the squabs. However, ivermectin was not detected in either the breast meat or the livers of squabs 1 wk after dosing. These results indicate that there is a rapid decline in tissue levels of ivermectin in squab.

Dissipation kinetics and safety evaluation of tebuconazole and trifloxystrobin in tea under tropical field conditions.

PubMed

Paramasivam, Mariappan; Deepa, Manthirachalam; Selvi, Chellamuthu; Chandrasekaran, Subramanian

2017-12-01

Dissipation kinetics of tebuconazole, trifloxystrobin and its acid metabolite residues were studied in tea under tropical field conditions using GC-MS (SIM). The average recoveries ranged from 80.7% to 105.8%, with a RSD of <9.3%. Dissipation rate for both doses applied followed first-order kinetics, with half-lives in green leaves in the range of 2.8-3.3 and 2.9-3.3 days; ranges in processed tea were 2.7-3.6 days for trifloxystrobin and 3.0-3.1 days for tebuconazole. The trifloxystrobin residues were not transferred into the tea infusion during the infusion process; tebuconazole did transfer, in the range of 14.3-18.9%. As the theoretical maximum residue contributions on tea from initial deposits were found to be less than the maximum permissible intake values, at the recommended application dose a withdrawal period of 23 days before consumption should be applied to reduce risk.

Residual Stress Distribution and Microstructure of a Multiple Laser-Peened Near-Alpha Titanium Alloy

NASA Astrophysics Data System (ADS)

Umapathi, A.; Swaroop, S.

2018-05-01

Laser peening without coating (LPwC) was performed on a Ti-2.5 Cu alloy with multiple passes (1, 3 and 5), using a Nd:YAG laser (1064 nm) at a constant overlap rate of 70% and power density of 6.7 GW cm-2. Hardness and residual stress profiles indicated thermal softening near the surface (< 100 μm) and bulk softening due to adiabatic heating. Maximum hardness (235 HV at 500 μm) and maximum residual stress (- 890 MPa at 100 μm) were observed for LPwC with 1 pass. Surface roughness and surface 3-D topography imaging showed that the surface roughness increased with the increase in the number of passes. XRD results indicated no significant β phases. However, peak shifts, broadening and asymmetry were observed and interpreted based on dislocation activity. Microstructures indicated no melting or resolidification or refinement of grains at the surface. Twin density was found to increase with the increase in the number of passes.

Organochlorine insecticide residues in soil and earthworms in the Delhi area, India, August-October 1974

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yadav, D.V.; Mittal, P.K.; Agarwal, H.C.

1981-09-01

DDT residues in soil and earthworms from 50 sites in Delhi were monitored. DDT was detected in all but two samples each of soil and earthworms. Among DDT residues, p,p'-DDE was most common and was found in 48 samples each of soil and earthworms; p,p'-DDT was detected in only 43 soil samples and 46 earthworm samples. p,p'-TDE and o,p'-DDT were also present in smaller concentrations in 29 and 15 soil samples and in 43 and 25 earthworm samples, respectively. Maximum total DDT concentration of 2.6 ppm was detected in the soil from Durga Nagar in the vicinity of a DDTmore » factory. The highest concentration of 37.7 ppm total DDT in earthworms was also obtained from the same site. The maximum concentration factor found in the earthworms was 551. The total DDT concentration in the earthworms and soil showed significant correlation.« less

Metabolism and Residues of 2,4-Dichlorophenoxyacetic Acid in DAS-40278-9 Maize (Zea mays) Transformed with Aryloxyalkanoate Dioxygenase-1 Gene.

PubMed

Zhou, Xiao; Rotondaro, Sandra L; Ma, Mingming; Rosser, Steve W; Olberding, Ed L; Wendelburg, Brian M; Adelfinskaya, Yelena A; Balcer, Jesse L; Blewett, T Craig; Clements, Bruce

2016-10-12

DAS-40278-9 maize, which is developed by Dow AgroSciences, has been genetically modified to express the aryloxyalkanoate dioxygenase-1 (AAD-1) protein and is tolerant to phenoxy auxin herbicides, such as 2,4-dichlorophenoxyacetic acid (2,4-D). To understand the metabolic route and residue distribution of 2,4-D in DAS-40278-9 maize, a metabolism study was conducted with 14 C-radiolabeled 2,4-D applied at the maximum seasonal rate. Plants were grown in boxes outdoors. Forage and mature grain, cobs, and stover were collected for analysis. The metabolism study showed that 2,4-D was metabolized to 2,4-dichlorophenol (2,4-DCP), which was then rapidly conjugated with glucose. Field-scale residue studies with 2,4-D applied at the maximum seasonal rate were conducted at 25 sites in the U.S. and Canada to measure the residues of 2,4-D and free and conjugated 2,4-DCP in mature forage, grain, and stover. Residues of 2,4-D were not detectable in the majority of the grain samples and averaged <1.0 and <1.5 μg/g in forage and stover, respectively. Free plus conjugated 2,4-DCP was not observed in grain and averaged <1.0 μg/g in forage and stover.

Ingestive Behavior of Ovine Fed with Marandu Grass Silage Added with Naturally Dehydrated Brewery Residue

PubMed Central

Lima de Souza, Alexandre; Divino Ribeiro, Marinaldo; Mattos Negrão, Fagton; Castro, Wanderson José Rodrigues; Valério Geron, Luiz Juliano; de Azevedo Câmara, Larissa Rodrigues

2016-01-01

The objective was to evaluate the ingestive behavior of ovine fed Marandu grass silage with dehydrated brewery residue added. The experiment had a completely randomized design with five treatments and four repetitions, with the treatments levels of inclusion being of 0, 10, 20, 30, and 40% natural matter of naturally dehydrated brewery residue for 36 hours to the marandu grass silage. 20 ovines were used and the experimental period was 21 days, 15 being for adaptation to diets. The use of brewery byproduct promoted quadratic effect (P < 0.05) for the consumption of dry matter with maximum point value estimated at adding 23.25% additive. Ingestion efficiency and rumination efficiency of dry matter (g DM/hour) were significant (P < 0.05), by quadratic behavior, and NDF ingestion and rumination efficiency showed crescent linear behavior. The DM and NDF consumption expressed in kg/meal and in minutes/kg were also significant (P < 0.05), showing quadratic behavior. Rumination activity expressed in g DM and NDF/piece was influenced (P < 0.05) by the adding of brewery residue in marandu grass silage in quadratic way, with maximum value estimated of 1.57 g DM/bolus chewed in inclusion of 24.72% additive in grass silage. The conclusion is that intermediary levels adding of 20 to 25% dehydrated brewery residue affects certain parameters of ingestive behavior. PMID:27547811

Expression and characterization of a new esterase with GCSAG motif from a permafrost metagenomic library.

PubMed

Petrovskaya, Lada E; Novototskaya-Vlasova, Ksenia A; Spirina, Elena V; Durdenko, Ekaterina V; Lomakina, Galina Yu; Zavialova, Maria G; Nikolaev, Evgeny N; Rivkina, Elizaveta M

2016-05-01

As a result of construction and screening of a metagenomic library prepared from a permafrost-derived microcosm, we have isolated a novel gene coding for a putative lipolytic enzyme that belongs to the hormone-sensitive lipase family. It encodes a polypeptide of 343 amino acid residues whose amino acid sequence displays maximum likelihood with uncharacterized proteins from Sphingomonas species. A putative catalytic serine residue of PMGL2 resides in a new variant of a recently discovered GTSAG sequence in which a Thr residue is replaced by a Cys residue (GCSAG). The recombinant PMGL2 was produced in Escherichia coli cells and purified by Ni-affinity chromatography. The resulting protein preferably utilizes short-chain p-nitrophenyl esters (C4 and C8) and therefore is an esterase. It possesses maximum activity at 45°C in slightly alkaline conditions and has limited thermostability at higher temperatures. Activity of PMGL2 is stimulated in the presence of 0.25-1.5 M NaCl indicating the good salt tolerance of the new enzyme. Mass spectrometric analysis demonstrated that N-terminal methionine in PMGL2 is processed and cysteine residues do not form a disulfide bond. The results of the study demonstrate the significance of the permafrost environment as a unique genetic reservoir and its potential for metagenomic exploration. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Assessment of Dithiocarbamate Residues on Tomatoes Conventionally Grown in Uganda and the Effect of Simple Washing to Reduce Exposure Risk to Consumers.

PubMed

Atuhaire, Aggrey; Kaye, Emmanuel; Mutambuze, Innocent Louis; Matthews, Graham; Friedrich, Theodor; Jørs, Erik

2017-01-01

Pesticide misuse by farmers poses health risks to consumers. This study assessed the level of dithiocarbamate residues in tomatoes acquired from 20 farmers and 25 market vendors in Wakiso District, how simple washing affects these residues, and the potential chronic health risk for Ugandans eating such tomatoes. Results revealed that mancozeb was the only reported dithiocarbamate, and 47.4% and 14% of farm and market samples, respectively, had dithiocarbamate residues exceeding the Codex alimentarius maximum residue limit of 2 mgCS 2 /kg. Mixing concentration had a positive significant effect on dithiocarbamate residue levels ( P = 0.004). Washing reduced dithiocarbamate residues by a factor of 0.3. Dietary risk assessment revealed no chronic health risk to both children and general population when a national daily per capita consumption of 1.0 g is considered. This study recommends comprehensive research into Uganda's food production and consumption patterns and establishment of a national pesticide residue surveillance program.

Assessment of Dithiocarbamate Residues on Tomatoes Conventionally Grown in Uganda and the Effect of Simple Washing to Reduce Exposure Risk to Consumers

PubMed Central

Atuhaire, Aggrey; Kaye, Emmanuel; Mutambuze, Innocent Louis; Matthews, Graham; Friedrich, Theodor; Jørs, Erik

2017-01-01

Pesticide misuse by farmers poses health risks to consumers. This study assessed the level of dithiocarbamate residues in tomatoes acquired from 20 farmers and 25 market vendors in Wakiso District, how simple washing affects these residues, and the potential chronic health risk for Ugandans eating such tomatoes. Results revealed that mancozeb was the only reported dithiocarbamate, and 47.4% and 14% of farm and market samples, respectively, had dithiocarbamate residues exceeding the Codex alimentarius maximum residue limit of 2 mgCS2/kg. Mixing concentration had a positive significant effect on dithiocarbamate residue levels (P = 0.004). Washing reduced dithiocarbamate residues by a factor of 0.3. Dietary risk assessment revealed no chronic health risk to both children and general population when a national daily per capita consumption of 1.0 g is considered. This study recommends comprehensive research into Uganda’s food production and consumption patterns and establishment of a national pesticide residue surveillance program. PMID:28615952

Continuous tidal streamflow, water level, and specific conductance data for Union Creek and the Little Back, Middle, and Front Rivers, Savannah River Estuary, November 2008 to March 2009

USGS Publications Warehouse

Lanier, Timothy H.; Conrads, Paul

2010-01-01

In the Water Resource Development Act of 1999, the U.S. Congress authorized the deepening of the Savannah Harbor. Additional studies were then identified by the Georgia Ports Authority and other local and regional stakeholders to determine and fully describe the potential environmental effects of deepening the channel. One need that was identified was the validation of a three-dimensional hydrodynamic model developed to evaluate mitigation scenarios for a potential harbor deepening and the effects on the Savannah River estuary. The streamflow in the estuary is very complex due to reversing tidal flows, interconnections of streams and tidal creeks, and the daily flooding and draining of the marshes. The model was calibrated using very limited streamflow data and no continuous streamflow measurements. To better characterize the streamflow dynamics and mass transport of the estuary, two index-velocity sites were instrumented with continuous acoustic velocity, water level, and specific conductance sensors on the Little Back and Middle Rivers for the 5-month period of November 2008 through March 2009. During the same period, a third acoustic velocity meter was installed on the Front River just downstream from U.S. Geological Survey streamgaging station 02198920 (Savannah River at GA 25, at Port Wentworth, Georgia) where water level and specific conductance data were being collected. A fourth index-velocity site was instrumented with continuous acoustic velocity, water level, and specific conductance sensors on Union Creek for a 2-month period starting in November 2008. In addition to monitoring the tidal cycles, streamflow measurements were made at the four index-velocity sites to develop ratings to compute continuous discharge for each site. The maximum flood (incoming) and ebb (outgoing) tides measured on Little Back River were –4,570 and 7,990 cubic feet per second, respectively. On Middle River, the maximum flood and ebb tides measured were –9,630 and 13,600 cubic feet per second, respectively. On Front River, the maximum flood and ebb tides were –34,500 and 43,700 cubic feet per second, respectively; and on Union Creek, the maximum flood and ebb tides were –2,390 and 4,610 cubic feet per second, respectively. During the 5-month instrumentation deployment, computed tidal streamflows on Little Back River ranged from –7,820 to 9,600 cubic feet per second for the flood and ebb tides, respectively. On Middle River, the computed tidal streamflows ranged from –17,500 to 22,500 cubic feet per second for the flood and ebb tides, respectively. The computed tidal streamflows on Front River ranged from –78,900 to 87,200 cubic feet per second, and from –3,850 to 6,130 cubic feet per second on Union Creek for the flood and ebb tides, respectively. The streamgages on the Little Back, Middle, and Front Rivers have continued in operation following the initial 5-month deployment.

Rate of degradation of lambda-cyhalothrin and methomyl in grapes (Vitis vinifera L.).

PubMed

Banerjee, Kaushik; Upadhyay, Ajay Kumar; Adsule, Pandurang G; Patil, Sangram H; Oulkar, Dasharath P; Jadhav, Deepak R

2006-10-01

Rates of degradation of lambda-cyhalothrin and methomyl residues in grape are reported. The dissipation behavior of both insecticides followed first-order rate kinetics with similar patterns at standard and double-dose applications. Residues of lambda-cyhalothrin were lost with pre-harvest intervals (PHI) of 12.0-12.5 and 15.0-15.5 days, corresponding to the applications at 25 and 50 g a.i. ha-1, respectively. In the case of methomyl, residues were lost with PHI of 55.0 and 61.0 days, following applications at 1 and 2 kg a.i. ha-1, respectively. The PHI, recommended on the basis of the experimental results, was shown to be effective in minimizing residue load of these insecticides below their maximum residue limits (MRLs) in vineyard samples.

Development of Local Amplification Factors in the NEAM Region for Production of Regional Tsunami Hazard Maps

NASA Astrophysics Data System (ADS)

Harbitz, C. B.; Glimsdal, S.; Løvholt, F.; Orefice, S.; Romano, F.; Brizuela, B.; Lorito, S.; Hoechner, A.; Babeyko, A. Y.

2016-12-01

The standard way of estimating tsunami inundation is by applying numerical depth-averaged shallow-water run-up models. However, for a regional Probabilistic Tsunami Hazard Assessment (PTHA), applying such inundation models may be too time-consuming. A faster, yet less accurate procedure, is to relate the near-shore surface elevations at offshore points to maximum shoreline water levels by using a set of amplification factors based on the characteristics of the incident wave and the bathymetric slope. The surface elevation at the shoreline then acts as a rough approximation for the maximum inundation height or run-up height along the shoreline. An amplification-factor procedure based on a limited set of idealized broken shoreline segments has previously been applied to estimate the maximum inundation heights globally. Here, we present a study where this technique is developed further, by taking into account the local bathymetric profiles. We extract a large number of local bathymetric transects over a significant part of the North East Atlantic, the Mediterranean and connected seas (NEAM) region. For each bathymetric transect, we compute the wave amplification from an offshore control point to points close to the shoreline using a linear shallow-water model for waves of different period and polarity with a sinusoidal pulse wave as input. The amplification factors are then tabulated. We present maximum water levels from the amplification factor method, and compare these with results from conventional inundation models. Finally, we demonstrate how the amplification factor method can be convolved with PTHA results to provide regional tsunami hazard maps. This work has been supported by the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement 603839 (Project ASTARTE), and the TSUMAPS-NEAM Project (http://www.tsumapsneam.eu/), co-financed by the European Union Civil Protection Mechanism, Agreement Number: ECHO/SUB/2015/718568/PREV26.

Development of Local Amplification Factors in the NEAM Region for Production of Regional Tsunami Hazard Maps

NASA Astrophysics Data System (ADS)

Glimsdal, Sylfest; Løvholt, Finn; Bonnevie Harbitz, Carl; Orefice, Simone; Romano, Fabrizio; Brizuela, Beatriz; Lorito, Stefano; Hoechner, Andreas; Babeyko, Andrey

2017-04-01

The standard way of estimating tsunami inundation is by applying numerical depth-averaged shallow-water run-up models. However, for a regional Probabilistic Tsunami Hazard Assessment (PTHA), applying such inundation models may be too time-consuming. A faster, yet less accurate procedure, is to relate the near-shore surface elevations at offshore points to maximum shoreline water levels by using a set of amplification factors based on the characteristics of the incident wave and the bathymetric slope. The surface elevation at the shoreline then acts as a rough approximation for the maximum inundation height or run-up height along the shoreline. An amplification-factor procedure based on a limited set of idealized broken shoreline segments has previously been applied to estimate the maximum inundation heights globally. Here, we present a study where this technique is developed further, by taking into account the local bathymetric profiles. We extract a large number of local bathymetric transects over a significant part of the North East Atlantic, the Mediterranean and connected seas (NEAM region). For each bathymetric transect, we compute the wave amplification from an offshore control point to points close to the shoreline using a linear shallow-water model for waves of different period and polarity with a sinusoidal pulse wave as input. The amplification factors are then tabulated. We present maximum water levels from the amplification factor method, and compare these with results from conventional inundation models. Finally, we demonstrate how the amplification factor method can be convolved with PTHA results to provide regional tsunami hazard maps. This work has been supported by the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement 603839 (Project ASTARTE), and the TSUMAPS-NEAM Project (http://www.tsumapsneam.eu/), co-financed by the European Union Civil Protection Mechanism, Agreement Number: ECHO/SUB/2015/718568/PREV26.

Residue decline and risk assessment of fluopyram + tebuconazole (400SC) in/on onion (Allium cepa).

PubMed

Patel, Badal V; Chawla, Suchi; Gor, Hetal; Upadhyay, Payal; Parmar, Kaushik D; Patel, Anil R; Shah, Paresh G

2016-10-01

A method was validated for estimating fluopyram and tebuconazole in onion on LC-MS/MS using dispersive QuEChERS. Three sprays of a combination fungicide fluopyram + tebuconazole (Luna experience, 400 SC) were applied @ 75 + 75 and 150 + 150 g a.i. ha -1 at an interval of 10 days on onion using Knapsack sprayer. First spray was made at bulb setting stage. Spring onion samples were drawn at 0 (1 h), 1, 3, 5, 7, 10, 15, and 20 days and matured onion bulb at harvest (52 days) after the last spray. Soil samples were also drawn at harvest. Foliar application of the combination product resulted in 1.14 and 2.86 mg kg -1 fluopyram residues on spring onion at standard and double dose, respectively, one hour after the last application. The levels of fluopyram residues gradually declined and recorded 0.25 and 0.58 mg kg -1 on 20th day of application with half-lives of 8.8 and 9.1 days at standard and double dose, respectively. For tebuconazole, the corresponding residues observed after 1 h (0 day) of application were 0.92 and 2.29 mg kg -1 . The levels declined gradually to 0.12 and 0.33 mg kg -1 on 20th days with half-life of 6.7 to 7.7 days at standard and double dose, respectively. Here, we are proposing a pre-harvest interval of 7 day for fluopyram and tebuconazole in spring onion when applied at 75 + 75 g a.i. ha -1 (400 SC). Risk assessment was done by calculating hazard quotient and by comparing theoretical maximum residue intake (TMRI) with maximum permissible intake (MPI). In all the cases, results of the study showed that HQ (Hazard Quotient) ≤1 and TMDI < MPI. Hence, the use of this combination product can be recommended with pre harvest interval of 7 days. The data can be used in establishing MRLs (maximum residue limits) for spring onion after considering multilocation trials.

Multi-residue analysis of pesticides, plant hormones, veterinary drugs and mycotoxins using HILIC chromatography - MS/MS in various food matrices.

PubMed

Danezis, G P; Anagnostopoulos, C J; Liapis, K; Koupparis, M A

2016-10-26

One of the recent trends in Analytical Chemistry is the development of economic, quick and easy hyphenated methods to be used in a field that includes analytes of different classes and physicochemical properties. In this work a multi-residue method was developed for the simultaneous determination of 28 xenobiotics (polar and hydrophilic) using hydrophilic interaction liquid chromatography technique (HILIC) coupled with triple quadrupole mass spectrometry (LC-MS/MS) technology. The scope of the method includes plant growth regulators (chlormequat, daminozide, diquat, maleic hydrazide, mepiquat, paraquat), pesticides (cyromazine, the metabolite of the fungicide propineb PTU (propylenethiourea), amitrole), various multiclass antibiotics (tetracyclines, sulfonamides quinolones, kasugamycin and mycotoxins (aflatoxin B1, B2, fumonisin B1 and ochratoxin A). Isolation of the analytes from the matrix was achieved with a fast and effective technique. The validation of the multi-residue method was performed at the levels: 10 μg/kg and 100 μg/kg in the following representative substrates: fruits-vegetables (apples, apricots, lettuce and onions), cereals and pulses (flour and chickpeas), animal products (milk and meat) and cereal based baby foods. The method was validated taking into consideration EU guidelines and showed acceptable linearity (r ≥ 0.99), accuracy with recoveries between 70 and 120% and precision with RSD ≤ 20% for the majority of the analytes studied. For the analytes that presented accuracy and precision values outside the acceptable limits the method still is able to serve as a semi-quantitative method. The matrix effect, the limits of detection and quantification were also estimated and compared with the current EU MRLs (Maximum Residue Levels) and FAO/WHO MLs (Maximum Levels) or CXLs (Codex Maximum Residue Limits). The combined and expanded uncertainty of the method for each analyte per substrate, was also estimated. Copyright © 2016 Elsevier B.V. All rights reserved.

A study on experimental characteristic of microwave-assisted pyrolysis of microalgae.

PubMed

Hu, Zhifeng; Ma, Xiaoqian; Chen, Chunxiang

2012-03-01

The microwave-assisted pyrolysis of Chlorella vulgaris was carried out under different microwave power levels, catalysts and contents of activated carbon and solid residue. The products, pyrolysis temperature and temperature rising rate were analyzed in order to obtain the optimal conditions. The results indicated that the higher the microwave power level was, the higher the maximum temperature rising rate and pyrolysis temperature were. The maximum bio-oil yield (35.83 wt.%) and gas yield (52.37%) were achieved under the microwave power of 1500 W and 2250 W, respectively. And 2250 W was the optimal power to obtain bio-fuel product. High microwave power level and catalyst can enhance the production of gas. Catalysts can promote the pyrolysis of C. vulgaris, and activated carbon was the best among the tested catalysts followed by the solid residue. The optimal content of activated carbon is 5% with the maximum bio-fuel yield of 87.47%. Copyright © 2011 Elsevier Ltd. All rights reserved.

Production of surfactin from rice mill polishing residue by submerged fermentation using Bacillus subtilis MTCC 2423.

PubMed

Gurjar, Jigar; Sengupta, Bina

2015-08-01

Rice mill polishing residue (RMPR), an abundant and cheap agro residue, was used as substrate for microbial growth of Bacillus subtilis MTCC 2423 by submerged fermentation process to produce surfactin. Nutrients present in the residue were sufficient to sustain the growth of the microorganism. Multi stage foam fractionation followed by acid precipitation was used to concentrate and recover the product. Recoverable yield of surfactin was 4.17 g/kg residue. Product recovered in the foamate accounted for 69% of the total yield. The residual broth containing ∼ 30% surfactin exhibited biological oxygen demand and chemical oxygen demand values of 23 and 69 mg/L respectively. The microbial growth data was correlated using three parameter sigmoid models. Surfactin synthesized had a predominance of molecular weight 1076 Da. Foam separation of copper using surfactin resulted in a maximum removal of 72.5%. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of fatigue and environment on residual strengths of center-cracked graphite/epoxy buffer strip panels

NASA Technical Reports Server (NTRS)

Bigelow, Catherine A.

1989-01-01

The effects of fatigue, moisture conditioning, and heating on the residual tension strengths of center-cracked graphite/epoxy buffer strip panels were evaluated using specimens made with T300/5208 graphite epoxy in a 16-ply quasi-isotropic layup, with two different buffer strip materials, Kevlar-49 or S-glass. It was found that, for panels subjected to fatigue loading, the residual strengths were not significantly affected by the fatigue loading, the number of repetitions of the loading spectrum, or the maximum strain level. The moisture conditioning reduced the residual strengths of the S-glass buffer strip panels by 10 to 15 percent below the ambient results, but increased the residual strengths of the Kevlar-49 buffer strip panels slightly. For both buffer strip materials, the heat increased the residual strengths of the buffer strip panels slightly over the ambient results.

An Overview on Recent Progress in Electrochemical Biosensors for Antimicrobial Drug Residues in Animal-Derived Food

PubMed Central

Majdinasab, Marjan; Yaqub, Mustansara; Rahim, Abdur; Catanante, Gaelle; Hayat, Akhtar; Marty, Jean Louis

2017-01-01

Anti-microbial drugs are widely employed for the treatment and cure of diseases in animals, promotion of animal growth, and feed efficiency. However, the scientific literature has indicated the possible presence of antimicrobial drug residues in animal-derived food, making it one of the key public concerns for food safety. Therefore, it is highly desirable to design fast and accurate methodologies to monitor antimicrobial drug residues in animal-derived food. Legislation is in place in many countries to ensure antimicrobial drug residue quantities are less than the maximum residue limits (MRL) defined on the basis of food safety. In this context, the recent years have witnessed a special interest in the field of electrochemical biosensors for food safety, based on their unique analytical features. This review article is focused on the recent progress in the domain of electrochemical biosensors to monitor antimicrobial drug residues in animal-derived food. PMID:28837093

Axial residual stresses in boron fibers

NASA Technical Reports Server (NTRS)

Behrendt, D. R.

1978-01-01

The axial residual stress distribution as a function of radius was determined from the fiber surface to the core including the average residual stress in the core. Such measurements on boron on tungsten (B/W) fibers show that the residual stresses for 102, 142, 203, and 366 micron diameter fibers were similar, being compressive at the surface and changing monotonically to a region of tensile within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile stress of about 860 mn/sq.m and then decreases to a compressive stress near the tungsten boride core. Data were presented for 203 micron diameter B/W fibers that show annealing above 900 C reduces the residual stresses. A comparison between 102 micron diameter B/W and boron on carbon (b/C) shows that the residual stresses were similar in the outer regions of the fibers, but that large differences near and in the core were observed. The effects of these residual stresses on the fracture of boron fibers were discussed.

Residue pattern of polycyclic aromatic hydrocarbons during green tea manufacturing and their transfer rates during tea brewing.

PubMed

Gao, Guanwei; Chen, Hongping; Liu, Pingxiang; Hao, Zhenxia; Ma, Guicen; Chai, Yunfeng; Wang, Chen; Lu, Chengyin

2017-06-01

Residues of polycyclic aromatic hydrocarbons (PAHs) in green tea and tea infusion were determined using gas chromatography-tandem mass spectrometry to study their dissipation pattern during green tea processing and infusion. Concentration and evaporation of PAHs during tea processing were the key factors affecting PAH residue content in product intermediates and in green tea. PAH residues in tea leaves increased by 2.4-3.1 times during the manufacture of green tea using the electric heating model. After correction to dry weight, PAH residue concentrations decreased by 33.5-48.4% during green tea processing because of PAH evaporation. Moreover, spreading and drying reduced PAH concentrations. The transfer rates of PAH residues from green tea to infusion varied from 4.6% to 7.2%, and PAH leaching was higher in the first infusion than in the second infusion. These results are useful for assessing exposure to PAHs from green tea and in formulating controls for the maximum residue level of PAHs in green tea.

Effect of radiance-to-reflectance transformation and atmosphere removal on maximum likelihood classification accuracy of high-dimensional remote sensing data

NASA Technical Reports Server (NTRS)

Hoffbeck, Joseph P.; Landgrebe, David A.

1994-01-01

Many analysis algorithms for high-dimensional remote sensing data require that the remotely sensed radiance spectra be transformed to approximate reflectance to allow comparison with a library of laboratory reflectance spectra. In maximum likelihood classification, however, the remotely sensed spectra are compared to training samples, thus a transformation to reflectance may or may not be helpful. The effect of several radiance-to-reflectance transformations on maximum likelihood classification accuracy is investigated in this paper. We show that the empirical line approach, LOWTRAN7, flat-field correction, single spectrum method, and internal average reflectance are all non-singular affine transformations, and that non-singular affine transformations have no effect on discriminant analysis feature extraction and maximum likelihood classification accuracy. (An affine transformation is a linear transformation with an optional offset.) Since the Atmosphere Removal Program (ATREM) and the log residue method are not affine transformations, experiments with Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were conducted to determine the effect of these transformations on maximum likelihood classification accuracy. The average classification accuracy of the data transformed by ATREM and the log residue method was slightly less than the accuracy of the original radiance data. Since the radiance-to-reflectance transformations allow direct comparison of remotely sensed spectra with laboratory reflectance spectra, they can be quite useful in labeling the training samples required by maximum likelihood classification, but these transformations have only a slight effect or no effect at all on discriminant analysis and maximum likelihood classification accuracy.

Determination of triazine herbicides in seaweeds: development of a sample preparation method based on Matrix Solid Phase Dispersion and Solid Phase Extraction Clean-up.

PubMed

Rodríguez-González, N; González-Castro, M J; Beceiro-González, E; Muniategui-Lorenzo, S; Prada-Rodríguez, D

2014-04-01

A method using dual process columns of Matrix Solid Phase Dispersion (MSPD) and Solid Phase Extraction (SPE) has been developed for extracting and cleaning-up of nine triazine herbicides (ametryn, atrazine, cyanazine, prometryn, propazine, simazine, simetryn, terbuthylazine and terbutryn) in seaweed samples. Under optimized conditions, samples were blended with 2g of octasilyl-derivatized silica (C8) and transferred into an SPE cartridge containing ENVI-Carb II/PSA (0.5/0.5 g) as a clean up co-sorbent. Then the dispersed sample was washed with 10 mL of n-hexane and triazines were eluted with 20 mL ethyl acetate and 5 mL acetonitrile. Finally the extract was concentrated to dryness, re-constituted with 1 mL methanol:water (1:1) and injected into the HPLC-DAD system. The linearity of the calibration curves was excellent in matrix matched standards, and yielded the coefficients of determination>0.995 for all the target analytes. The recoveries ranged from 75% to 100% with relative standard deviations lower than 7%. The achieved LOQs (<10 µg kg(-1)) for all triazines under study permits to ensure proper determination at the maximum allowed residue levels set in the European Union Legislation. Samples of three seaweeds were subjected to the procedure proving the suitability of MSPD method for the analysis of triazines in different seaweeds samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Probabilistic Estimation of Critical Flaw Sizes in the Primary Structure Welds of the Ares I-X Launch Vehicle

NASA Technical Reports Server (NTRS)

Pai, Shantaram S.; Hoge, Peter A.; Patel, B. M.; Nagpal, Vinod K.

2009-01-01

The primary structure of the Ares I-X Upper Stage Simulator (USS) launch vehicle is constructed of welded mild steel plates. There is some concern over the possibility of structural failure due to welding flaws. It was considered critical to quantify the impact of uncertainties in residual stress, material porosity, applied loads, and material and crack growth properties on the reliability of the welds during its pre-flight and flight. A criterion--an existing maximum size crack at the weld toe must be smaller than the maximum allowable flaw size--was established to estimate the reliability of the welds. A spectrum of maximum allowable flaw sizes was developed for different possible combinations of all of the above listed variables by performing probabilistic crack growth analyses using the ANSYS finite element analysis code in conjunction with the NASGRO crack growth code. Two alternative methods were used to account for residual stresses: (1) The mean residual stress was assumed to be 41 ksi and a limit was set on the net section flow stress during crack propagation. The critical flaw size was determined by parametrically increasing the initial flaw size and detecting if this limit was exceeded during four complete flight cycles, and (2) The mean residual stress was assumed to be 49.6 ksi (the parent material s yield strength) and the net section flow stress limit was ignored. The critical flaw size was determined by parametrically increasing the initial flaw size and detecting if catastrophic crack growth occurred during four complete flight cycles. Both surface-crack models and through-crack models were utilized to characterize cracks in the weld toe.

Risk assessment and monitoring of dinotefuran and its metabolites for Chinese consumption of apples.

PubMed

Yu, Weiwei; Huang, Min; Chen, Jiaojiao; Wu, Sizhuo; Zheng, Kunming; Zeng, Song; Zhang, Kankan; Hu, Deyu

2017-09-26

Residues of dinotefuran and its metabolites, 1-methyl-3-(tetrahydro-3-furylmethyl)urea (UF) and 1-methyl-3-(tetrahydro-3-furylmethyl)guanidine (DN), in apple were investigated using a "QuEChERS" (quick, easy, cheap, effective, rugged, safe) pretreatment and liquid chromatography-tandem mass spectrometry. Limits of detection (LODs) and quantification (LOQs) of dinotefuran, UF, and DN in apples were 0.011-0.960 and 0.037-3.200 μg/kg, respectively. The average recoveries of dinotefuran, UF, and DN in apple ranged from 70.0 to 83.6% with relative standard deviations less than 13%. A formulation of 20% water-dispersible dinotefuran granules was sprayed at 1-1.5-fold the recommended dose 3-4 times on apple trees. Total terminal residues of dinotefuran in apple were less than 2 mg/kg, which is the maximum residue limit (MRL) set by Japan. When following the recommended application guidelines, dinotefuran is unlikely to present significant health concerns to the Chinese population because the risk quotient (RQ) is less than 100%. This work could provide guidance for the safe use of dinotefuran and serve as a reference for the establishment of a maximum residue limit of dinotefuran in apple in China.

Dissipation pattern and risk assessment studies of triazophos residues on capsicum (Capsicum annuum L.) using GLC-FPD and GC-MS.

PubMed

Singh, Yadwinder; Mandal, Kousik; Singh, Balwinder

2015-10-01

The present study was carried out to observe the dissipation pattern of triazophos on capsicum and risk assessment of its residues on human beings and to suggest a waiting period for the safety of consumers. Following two applications of triazophos (Truzo 40 EC) at 500 and 1000 g a.i. ha(-1), the average initial deposits were found to be 3.61 and 6.26 mg kg(-1), respectively. These residues dissipated below the limit of quantification (LOQ) of 0.05 mg kg(-1) in 10 and 15 days at the recommended and double the recommended dosages, respectively. The calculated values of half-life were 2.31 and 2.14 days at recommended and double the recommended dosages, respectively. Theoretical maximum residue contribution (TMRC) values were found to be 28.8 and 41.6 μg person(-1) day(-1) at 500 and 1000 g a.i. ha(-1), respectively, and found to be below the maximum permissible intake on capsicum fruit on the 7th day. Therefore, a waiting period of 7 days is suggested for consumption of capsicum sprayed with triazophos at the recommended dosages.

Parametric models to compute tryptophan fluorescence wavelengths from classical protein simulations.

PubMed

Lopez, Alvaro J; Martínez, Leandro

2018-02-26

Fluorescence spectroscopy is an important method to study protein conformational dynamics and solvation structures. Tryptophan (Trp) residues are the most important and practical intrinsic probes for protein fluorescence due to the variability of their fluorescence wavelengths: Trp residues emit in wavelengths ranging from 308 to 360 nm depending on the local molecular environment. Fluorescence involves electronic transitions, thus its computational modeling is a challenging task. We show that it is possible to predict the wavelength of emission of a Trp residue from classical molecular dynamics simulations by computing the solvent-accessible surface area or the electrostatic interaction between the indole group and the rest of the system. Linear parametric models are obtained to predict the maximum emission wavelengths with standard errors of the order 5 nm. In a set of 19 proteins with emission wavelengths ranging from 308 to 352 nm, the best model predicts the maximum wavelength of emission with a standard error of 4.89 nm and a quadratic Pearson correlation coefficient of 0.81. These models can be used for the interpretation of fluorescence spectra of proteins with multiple Trp residues, or for which local Trp environmental variability exists and can be probed by classical molecular dynamics simulations. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Determination of cyflumetofen residue in water, soil, and fruits by modified quick, easy, cheap, effective, rugged, and safe method coupled to gas chromatography/tandem mass spectrometry.

PubMed

Li, Minmin; Liu, Xingang; Dong, Fengshou; Xu, Jun; Qin, Dongmei; Zheng, Yongquan

2012-10-01

A new, highly sensitive, and selective method was developed for the determination of the cyflumetofen residue in water, soil, and fruits by using gas chromatography quadruple mass spectrometry. The target compound was extracted using acetonitrile and then cleaned up using dispersive solid-phase extraction with primary and secondary amine and graphitized carbon black, and optionally by a freezing-out cleanup step. The matrix-matched standards gave satisfactory recoveries and relative standard deviation values in different matrices at three fortified levels (0.05, 0.5, and 1.0 mg kg(-1) ). The overall average recoveries for this method in water, soil, and all fruits matrix at three fortified levels ranged from 76.3 to 101.5% with relative standard deviations in the range of 1.2-11.8% (n = 5). The calculated limits of detection and quantification were typically below 0.005 and 0.015 μg kg(-1), which were much lower than the maximum residue levels established by Japanese Positive List. This study provides a theoretical basis for China to draw up maximum residue level and analytical method for cyflumetofen acaricide in different fruits. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Skeletal maturation, fundamental motor skills and motor coordination in children 7-10 years.

PubMed

Freitas, Duarte L; Lausen, Berthold; Maia, José António; Lefevre, Johan; Gouveia, Élvio Rúbio; Thomis, Martine; Antunes, António Manuel; Claessens, Albrecht L; Beunen, Gaston; Malina, Robert M

2015-01-01

Relationships between skeletal maturation and fundamental motor skills and gross motor coordination were evaluated in 429 children (213 boys and 216 girls) 7-10 years. Skeletal age was assessed (Tanner-Whitehouse 2 method), and stature, body mass, motor coordination (Körperkoordinations Test für Kinder, KTK) and fundamental motor skills (Test of Gross Motor Development, TGMD-2) were measured. Relationships among chronological age, skeletal age (expressed as the standardised residual of skeletal age on chronological age) and body size and fundamental motor skills and motor coordination were analysed with hierarchical multiple regression. Standardised residual of skeletal age on chronological age interacting with stature and body mass explained a maximum of 7.0% of the variance in fundamental motor skills and motor coordination over that attributed to body size per se. Standardised residual of skeletal age on chronological age alone accounted for a maximum of 9.0% of variance in fundamental motor skills, and motor coordination over that attributed to body size per se and interactions between standardised residual of skeletal age on chronological age and body size. In conclusion, skeletal age alone or interacting with body size has a negligible influence on fundamental motor skills and motor coordination in children 7-10 years.

Residue depletion of tilmicosin in cattle after subcutaneous administration.

PubMed

Jiang, Haiyang; Ding, Shuangyang; Li, Jiancheng; An, Dianjin; Li, Cun; Shen, Jianzhong

2006-07-12

A study of tissue residue depletion of tilmicosin in cattle was conducted after a single subcutaneous injection at the therapeutic level of 10 mg per kg body weight. Eighteen cross cattle were treated with the tilmicosin oil formulation (30%). Three treated animals (two males and one female) were selected randomly to be scarified at 1, 7, 14, 28, and 35 days withdrawal after injection. Samples of the injection site and of muscle, liver, kidney, and fat were collected. Tilmicosin residue concentrations were determined using a high-performance liquid chromatography (HPLC) method with a UV detector at 290 nm. Using a statistical method recommended by the Committee for Veterinary Medical Products of European Medical Evaluation Agency, the withdrawal time of 34 days was established when all tissue residues except samples in the injection site were below the accepted maximum residue limits.

LC-MS/MS measurement of ampicillin residue in chicken tissues at 2 days after in-feed administration

PubMed Central

HAMAMOTO, Kouko; MIZUNO, Yasuharu

2017-01-01

We assessed ampicillin (ABPC) concentrations of liver, kidney and skin at a 2-day withdrawal period in ten male and ten female White Leghorn chickens fed the diet containing ABPC (ABPC medicated feed 40 mg/kg body weight/day) for a week. The ABPC residues were measured with liquid chromatography–tandem mass spectrometry and the mean recoveries and quantitation limits ranged from 93.0% to 102.7% and from 0.1 to 1.4 ng/g, respectively. The residual ABPC concentrations were ≤7.82 ng/g for the skin and ≤0.64 ng/g for the kidney, suggesting below the Japanese provisional maximum residue limits. These results revealed that the analytical method is developed for residue ABPC and that the withdrawal period is appropriate. PMID:28190817

Determination and health risk assessment of enrofloxacin, flumequine and sulfamethoxazole in imported Pangasius catfish products in Thailand.

PubMed

Jansomboon, Worawat; Boontanon, Suwanna Kitpati; Boontanon, Narin; Polprasert, Chongrak

2018-02-01

The goals of this study were to determine the levels of three antibiotics - enrofloxacin, flumequine and sulfamethoxazole - in Pangasius catfish products imported into Thailand and to assess the health risks from consumption. To extract these antibiotic residues, acetonitrile, methanol and a small amount of formic acid were used as solvents. Determination of the antibiotics after extraction steps was carried out by liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS) technique. The results showed that 14 and 3 samples of Pangasius catfish products were contaminated with enrofloxacin and sulfamethoxazole, respectively. No flumequine residue was found. While the concentration levels of these antibiotics in most contaminated samples were lower than the European Union (EU) standard, one sample was found to contain sulfamethoxazole at 245.91 µg kg -1 , which was higher than the EU standard (100 µg kg -1 ), indicating the likelihood that some contaminated freshwater fish products are widely distributed in Thai markets. Notably, the concentration levels of enrofloxacin in samples of Pangasius catfish with skin were higher than in non-skin products, suggesting that products with skin might retain more antibiotic residues than non-skin products. Although the hazard quotient showed that consuming imported Pangasius catfish products, based on the current consumption rate, will not adversely affect consumer health, antibiotic residues in Pangasius catfish products imported into Thailand should be continually monitored.

Ammonia volatilization from crop residues and frozen green manure crops

NASA Astrophysics Data System (ADS)

de Ruijter, F. J.; Huijsmans, J. F. M.; Rutgers, B.

2010-09-01

Agricultural systems can lose substantial amounts of nitrogen (N). To protect the environment, the European Union (EU) has adopted several directives that set goals to limit N losses. National Emission Ceilings (NEC) are prescribed in the NEC directive for nitrogen oxides and ammonia. Crop residues may contribute to ammonia volatilization, but sufficient information on their contribution to the national ammonia volatilization is lacking. Experiments were carried out with the aim to assess the ammonia volatilization of crop residues left on the soil surface or incorporated into the soil under the conditions met in practice in the Netherlands during late autumn and winter. Ammonia emission from residues of broccoli, leek, sugar beet, cut grass, fodder radish (fresh and frozen) and yellow mustard (frozen) was studied during two winter seasons using volatilization chambers. Residues were either placed on top of soil or mixed with soil. Mixing residues with soil gave insignificant ammonia volatilization, whereas volatilization was 5-16 percent of the N content of residues when placed on top of soil. Ammonia volatilization started after at least 4 days. Total ammonia volatilization was related to C/N-ratio and N concentration of the plant material. After 37 days, cumulative ammonia volatilization was negligible from plant material with N concentration below 2 percent, and was 10 percent of the N content of plant material with 4 percent N. These observations can be explained by decomposition of plant material by micro-organisms. After an initial built up of the microbial population, NH 4+ that is not needed for their own growth is released and can easily emit as NH 3 at the soil surface. The results of the experiments were used to estimate the contribution of crop residues to ammonia volatilization in the Netherlands. Crop residues of arable crops and residues of pasture topping may contribute more than 3 million kg NH 3-N to the national ammonia volatilization of the Netherlands, being more than 3 percent of the national emissions in 2005. This contribution should therefore be considered when focusing on the national ceilings for ammonia emissions.

Overview regarding construction and demolition waste in Spain.

PubMed

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Morán-Del Pozo, Julia M; Guerra-Romero, M Ignacio

2015-01-01

The construction sector comprises a number of activities that may result in environmental impacts of considerable magnitude, waste generation being one of the major negative effects of this industry due to the large streams generated. Proper knowledge of the environmental problem caused by the sector is of great importance in order to achieve an effective waste management. Thus, this paper analyse the Spanish situation regarding construction and demolition waste (CDW) compared with other European Union countries; which sets out the current figures of the CDW scenario (legislation, generation, composition, treatment and market) as well as the difficulties encountered when handling this residue.

Tides and turbines

NASA Astrophysics Data System (ADS)

Charlier, R. H.

1980-12-01

Tidal power plants are examined with attention to potential sites worldwide and to existing projects in France, the Soviet Union, and China. It is noted that maximum power cannot always be made available during peak demand periods because of the continuous variation of the daily tidal cycle throughout the year. However, this can be alleviated if a two-pool design or pumping are used. The economic impact of tidal power has been favorable, with the use of cellular units reducing construction costs substantially.

Bulgaria’s Quest for Security After the Cold War

DTIC Science & Technology

1993-02-01

Chairman Filip Dimitrov , while welcoming close traditional relations with the Soviet people, held the Soviet Union at arms length in an interview on the...8217 intentions and to spur them to further reform.’ 4 The Bulgarians took maximum advantage of the visit. Foreign Minister Boyko Dimitrov told reporters the talks...Many of the older generation of the Bulgarian elite were nurtured in American schools. Founder of the Bulgarian Communist government Georgi Dimitrov had

A climatology of ⁷Be in surface air in European Union.

PubMed

Hernández-Ceballos, M A; Cinelli, G; Ferrer, M Marín; Tollefsen, T; De Felice, L; Nweke, E; Tognoli, P V; Vanzo, S; De Cort, M

2015-03-01

This study presents a European-wide analysis of the spatial and temporal distribution of the cosmogenic isotope (7)Be in surface air. This is the first time that a long term database of 34 sampling sites that regularly provide data to the Radioactivity Environmental Monitoring (REM) network, managed by the Joint Research Centre (JRC) in Ispra, is used. While temporal coverage varies between stations, some of them have delivered data more or less continuously from 1984 to 2011. The station locations were considerably heterogeneous, both in terms of latitude and altitude, a range which should ensure a high degree of representativeness of the results. The mean values of (7)Be activity concentration presented a spatial distribution value ranging from 2.0 to 5.4 mBq/m(3) over the European Union. The results of the ANOVA analysis of all (7)Be data available indicated that its temporal and spatial distributions were mainly explained by the location and characteristic of the sampling sites rather than its temporal distribution (yearly, seasonal and monthly). Higher (7)Be concentrations were registered at the middle, compared to high-latitude, regions. However, there was no correlation with altitude, since all stations are sited within the atmospheric boundary layer. In addition, the total and yearly analyses of the data indicated a dynamic range of (7)Be activity for each solar cycle and phase (maximum or minimum), different impact on stations having been observed according to their location. Finally, the results indicated a significant seasonal and monthly variation for (7)Be activity concentration across the European Union, with maximum concentrations occurring in the summer and minimum in the winter, although with differences in the values reached. The knowledge of the horizontal and vertical distribution of this natural radionuclide in the atmosphere is a key parameter for modelling studies of atmospheric processes, which are important phenomena to be taken into account in the case of a nuclear accident. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Match-play activity profile in elite women's rugby union players.

PubMed

Suarez-Arrones, Luis; Portillo, Javier; Pareja-Blanco, Fernando; Sáez de Villareal, Eduardo; Sánchez-Medina, Luis; Munguía-Izquierdo, Diego

2014-02-01

The aim of this study was to provide an objective description of the locomotive activities and exercise intensity undergone during the course of an international-level match of female rugby union. Eight players were analyzed using global positioning system tracking technology. The total distance covered by the players during the whole match was 5,820 ± 512 m. The backs covered significantly more distance than the forwards (6,356 ± 144 vs. 5,498 ± 412 m, respectively). Over this distance, 42.7% (2,487 ± 391 m) was spent standing or walking, 35% jogging (2,037 ± 315 m), 9.7% running at low intensity (566 ± 115 m), 9.5% at medium intensity (553 ± 190 m), 1.8% at high intensity (105 ± 74 m), and 1.2% sprinting (73 ± 107 m). There were significant differences in the distance covered by forwards and backs in certain speed zones. Analysis of the relative distance traveled over successive 10-minute period of match play revealed that the greatest distances were covered during the first (725 ± 53 m) and the last (702 ± 79 m) 10-minute period of the match. The average number of sprints, the average maximum distance of sprinting, the average minimum distance of sprinting, and the average sprint distance during the game were 4.7 ± 3.9 sprints, 20.6 ± 10.5 m, 5.8 ± 0.9 -m, and 12.0 ± 3.8 m, respectively. There were substantial differences between forwards and backs. Backs covered greater total distance, distance in certain speed zones, and sprinting performance. The players spent 46.9 ± 28.9% of match time between 91 and 100% of maximum heart rate and experienced a large number of impacts (accelerometer data and expressed as g forces) during the game. These findings offer important information to design better training strategies and physical fitness testing adapted to the specific demands of female rugby union.

What is new about covered interest parity condition in the European Union? Evidence from fractal cross-correlation regressions

NASA Astrophysics Data System (ADS)

Ferreira, Paulo; Kristoufek, Ladislav

2017-11-01

We analyse the covered interest parity (CIP) using two novel regression frameworks based on cross-correlation analysis (detrended cross-correlation analysis and detrending moving-average cross-correlation analysis), which allow for studying the relationships at different scales and work well under non-stationarity and heavy tails. CIP is a measure of capital mobility commonly used to analyse financial integration, which remains an interesting feature of study in the context of the European Union. The importance of this features is related to the fact that the adoption of a common currency is associated with some benefits for countries, but also involves some risks such as the loss of economic instruments to face possible asymmetric shocks. While studying the Eurozone members could explain some problems in the common currency, studying the non-Euro countries is important to analyse if they are fit to take the possible benefits. Our results point to the CIP verification mainly in the Central European countries while in the remaining countries, the verification of the parity is only residual.

Aerial gamma ray and magnetic survey: Powder River II Project, Newcastle Quadrangle, Wyoming. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-04-01

Thick Phanerozoic sediments (greater than 17,000 ft) fill the northwest trending Powder River Basin which is the dominant tectonic structure in the Newcastle quadrangle. Lower Tertiary sediments comprise more than 85% of exposed units at the surface of the Basin. A small portion of the Black Hills Uplift occupies the eastern edge of the quadrangle. Residual magnetics clearly reflect the great depth to crystalline Precambrian basement in the Basin. The Basin/Uplift boundary is not readily observed in the magnetic data. Economic uranium deposits of roll-type configuration are present in the southwest within the Monument Hill-Box Creek District in fluvial sandstonesmore » of the Paleocene Fort Union Formation. Numerous small claims and prospects are found in the Pumpkin Buttes-Turnercrest District in the northwest. Interpretation of the radiometric data resulted in 86 statistical uranium anomalies listed for this quadrangle. Most anomalies are in the eastern-central portion of the map within Tertiary Fort Union and Wasatch Formations. However, several lie in the known uranium districts in the southwest and northwest.« less

History of SO2 removal system at the Meramec plant of union electric.

PubMed

Dreifke, G E; McLaughlin, J F; Smith, J D

1975-01-01

In line with the then emerging air pollution control regulations Union Electric installed a limestone injection wet scrubber sulfur dioxide removal system on an intermediate size coal-fired utility boiler at its Meramec Power Plant on an experimental basis in September, 1968. Approximately 3 years of operation many difficulties were encountered with plugging and scaling of various system components by calcium sulphate. As a result of this experience along with related experiences by other utilities employing similar systems, the experiment was terminated in June, 1971. As a result of the experiences gained, however, second generation experiments in sulfur dioxide removal have been initiated elsewhere with the hope of improved performance. A number of experimental projects are still under tests. Costs in resources, reliability, and disposal of residual by-products are matters of great concern. The ture cost of sulfur dioxide removal systems in dollars and resources is not well known and perhaps a reevaluation of current and future SO2 removal projects is in order at this time before additional resources are committed.

[Certification of suitability of monographs of the European pharmacopoeia].

PubMed

Artiges, A

2002-09-01

In April 1994, t he European Pharmacopoeia Commission set up a new procedure for the "Certification of Suitability of Monographs of the European Pharmacopoela" to deal with the changing requirements of the licensing authorities and the growth of international trade, notably as regards raw materials to be used in the manufacture of medicines. This procedure was the result of extensive collaboration between the licensing authorities of the European Union and the other parties to the European Pharmacopoeia Convention, and it enables a manufacturer of a raw material for pharmaceutical use to demonstrate that the purity of their substance is suitably controlled by the monograph of the European Pharmacopoeia; this demonstration is now required by the guideline on "Requirements in Relation to Active Substances" published in Volume 3A of the Rules Governing Medicinal Products in the European Union. Initially set up in response to problems with impurities of synthesis and residual solvents that can vary from one manufacturer to another, the procedure has gradually been extended to a very wide range of products including products of fermentation and, more recently, products with risk of transmitting agents of animal spongiform encephalopathies.

Design of a software for calculating isoelectric point of a polypeptide according to their net charge using the graphical programming language LabVIEW.

PubMed

Tovar, Glomen

2018-01-01

A software to calculate the net charge and to predict the isoelectric point (pI) of a polypeptide is developed in this work using the graphical programming language LabVIEW. Through this instrument the net charges of the ionizable residues of the polypeptide chains of the proteins are calculated at different pH values, tabulated, pI is predicted and an Excel (-xls) type file is generated. In this work, the experimental values of the pIs (pI) of different proteins are compared with the values of the pIs (pI) calculated graphically, achieving a correlation coefficient (R) of 0.934746 which represents a good reliability for a p < 0.01. In this way the generated program can constitute an instrument applicable in the laboratory, facilitating the calculation to graduate students and junior researchers. © 2017 by The International Union of Biochemistry and Molecular Biology, 46(1):39-46, 2018. © 2017 The International Union of Biochemistry and Molecular Biology.

Differential effects of peroxynitrite on contractile protein properties in fast- and slow-twitch skeletal muscle fibers of rat.

PubMed

Dutka, T L; Mollica, J P; Lamb, G D

2011-03-01

Oxidative modification of contractile proteins is thought to be a key factor in muscle weakness observed in many pathophysiological conditions. In particular, peroxynitrite (ONOO(-)), a potent short-lived oxidant, is a likely candidate responsible for this contractile dysfunction. In this study ONOO(-) or 3-morpholinosydnonimine (Sin-1, a ONOO(-) donor) was applied to rat skinned muscle fibers to characterize the effects on contractile properties. Both ONOO(-) and Sin-1 exposure markedly reduced maximum force in slow-twitch fibers but had much less effect in fast-twitch fibers. The rate of isometric force development was also reduced without change in the number of active cross bridges. Sin-1 exposure caused a disproportionately large decrease in Ca(2+) sensitivity, evidently due to coproduction of superoxide, as it was prevented by Tempol, a superoxide dismutase mimetic. The decline in maximum force with Sin-1 and ONOO(-) treatments could be partially reversed by DTT, provided it was applied before the fiber was activated. Reversal by DTT indicates that the decrease in maximum force was due at least in part to oxidation of cysteine residues. Ascorbate caused similar reversal, further suggesting that the cysteine residues had undergone S-nitrosylation. The reduction in Ca(2+) sensitivity, however, was not reversed by either DTT or ascorbate. Western blot analysis showed cross-linking of myosin heavy chain (MHC) I, appearing as larger protein complexes after ONOO(-) exposure. The findings suggest that ONOO(-) initially decreases maximum force primarily by oxidation of cysteine residues on the myosin heads, and that the accompanying decrease in Ca(2+) sensitivity is likely due to other, less reversible actions of hydroxyl or related radicals.

Prediction of active sites of enzymes by maximum relevance minimum redundancy (mRMR) feature selection.

PubMed

Gao, Yu-Fei; Li, Bi-Qing; Cai, Yu-Dong; Feng, Kai-Yan; Li, Zhan-Dong; Jiang, Yang

2013-01-27

Identification of catalytic residues plays a key role in understanding how enzymes work. Although numerous computational methods have been developed to predict catalytic residues and active sites, the prediction accuracy remains relatively low with high false positives. In this work, we developed a novel predictor based on the Random Forest algorithm (RF) aided by the maximum relevance minimum redundancy (mRMR) method and incremental feature selection (IFS). We incorporated features of physicochemical/biochemical properties, sequence conservation, residual disorder, secondary structure and solvent accessibility to predict active sites of enzymes and achieved an overall accuracy of 0.885687 and MCC of 0.689226 on an independent test dataset. Feature analysis showed that every category of the features except disorder contributed to the identification of active sites. It was also shown via the site-specific feature analysis that the features derived from the active site itself contributed most to the active site determination. Our prediction method may become a useful tool for identifying the active sites and the key features identified by the paper may provide valuable insights into the mechanism of catalysis.

Beta agonists in livestock feed: status, health concerns, and international trade.

PubMed

Centner, T J; Alvey, J C; Stelzleni, A M

2014-09-01

Since the U.S. Food and Drug Administration approved ractopamine hydrochloride and zilpaterol hydrochloride in animal feeds, usage of those compounds has been a topic of worldwide debate. Ractopamine and zilpaterol are β-adrenergic agonists used as veterinary drugs to increase weight gain in certain animals raised for food. The Joint FAO/WHO Expert Committee on Food Additives (JECFA) established maximum residue limits for ractopamine, which were adopted by the Codex Alimentarius Commission (Codex). No maximum residue limits for zilpaterol have been adopted by JECFA, and new reports of animal mobility issues confront the use of this feed additive. However, many countries disagree with the Codex standards and are restricting or banning meat products containing β agonists. The bans by major importers of U.S. meat products have prompted some to advocate that the United States use the World Trade Organization dispute settlement body. This paper looks at the developments to provide a fuller accounting of what the issues may mean to U.S. firms selling meat products containing residues of β agonists.

Liquid chromatography-electrospray ionization tandem mass spectrometry and dynamic multiple reaction monitoring method for determining multiple pesticide residues in tomato.

PubMed

Andrade, G C R M; Monteiro, S H; Francisco, J G; Figueiredo, L A; Botelho, R G; Tornisielo, V L

2015-05-15

A quick and sensitive liquid chromatography-electrospray ionization tandem mass spectrometry method, using dynamic multiple reaction monitoring and a 1.8-μm particle size analytical column, was developed to determine 57 pesticides in tomato in a 13-min run. QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for samples preparations and validations was carried out in compliance with EU SANCO guidelines. The method was applied to 58 tomato samples. More than 84% of the compounds investigated showed limits of detection equal to or lower than 5 mg kg(-1). A mild (<20%), medium (20-50%), and strong (>50%) matrix effect was observed for 72%, 25%, and 3% of the pesticides studied, respectively. Eighty-one percent of the pesticides showed recoveries ranging between 70% and 120%. Twelve pesticides were detected in 35 samples, all below the maximum residue levels permitted in the Brazilian legislation; 15 samples exceeded the maximum residue levels established by the EU legislation for methamidophos; and 10 exceeded limits for acephate and four for bromuconazole. Copyright © 2014 Elsevier Ltd. All rights reserved.

21 CFR 184.1259 - Cocoa butter substitute.

Code of Federal Regulations, 2011 CFR

2011-04-01

... material incorporated by reference may be obtained from the AOAC INTERNATIONAL, 481 North Frederick Ave... in accordance with good manufacturing practice. (7) Residual methanol—5 parts per million maximum. (8...

21 CFR 184.1259 - Cocoa butter substitute.

Code of Federal Regulations, 2010 CFR

2010-04-01

... material incorporated by reference may be obtained from the AOAC INTERNATIONAL, 481 North Frederick Ave... in accordance with good manufacturing practice. (7) Residual methanol—5 parts per million maximum. (8...

Maximum residue level validation of triclabendazole marker residues in bovine liver, muscle and milk matrices by ultra high pressure liquid chromatography tandem mass spectrometry.

PubMed

Whelan, Michelle; O'Mahony, John; Moloney, Mary; Cooper, Kevin M; Furey, Ambrose; Kennedy, D Glenn; Danaher, Martin

2013-02-01

Triclabendazole is the only anthelmintic drug, which is active against immature, mature and adult stages of fluke. The objective of this work was to develop an analytical method to quantify and confirm the presence of triclabendazole residues around the MRL. In this work, a new analytical method was developed, which extended dynamic range to 1-100 and 5-1000 μg kg(-1) for milk and tissue, respectively. This was achieved using a mobile phase containing trifluoroacetic acid (pK(a) of 0.3), which resulted in the formation of the protonated pseudomolecular ions, [M+H](+), of triclabendazole metabolites. Insufficient ionisation of common mobile phase additives due to low pK(a) values (<2) was identified as the cause of poor linearity. The new mobile phase conditions allowed the analysis of triclabendazole residues in liver, muscle and milk encompassing their EU maximum residue levels (MRL) (250, 225 and 10 μg kg(-1) respectively). Triclabendazole residues were extracted using a modified QuEChERS method and analysed by positive electrospray ionisation mass spectrometry with all analytes eluted by 2.23 min. The method was validated at the MRL according to Commission Decision (CD) 2002/657/EC criteria. The decision limit (CCα) of the method was in the range of 250.8-287.2, 2554.9-290.8 and 10.9-12.1 μg kg(-1) for liver, muscle and milk, respectively. The performance of the method was successfully verified for triclabendazole in muscle by participating in a proficiency study, the method was also applied to incurred liver, muscle and milk samples. Copyright © 2012 Elsevier B.V. All rights reserved.

The ball in play demands of international rugby union.

PubMed

Pollard, Benjamin T; Turner, Anthony N; Eager, Robin; Cunningham, Daniel J; Cook, Christian J; Hogben, Patrick; Kilduff, Liam P

2018-03-03

Rugby union is a high intensity intermittent sport, typically analysed via set time periods or rolling average methods. This study reports the demands of international rugby union via global positioning system (GPS) metrics expressed as mean ball in play (BiP), maximum BiP (max BiP), and whole match outputs. Single cohort cross sectional study involving 22 international players, categorised as forwards and backs. A total of 88 GPS files from eight international test matches were collected during 2016. An Opta sportscode timeline was integrated into the GPS software to split the data into BiP periods. Metres per min (mmin -1 ), high metabolic load per min (HML), accelerations per min (Acc), high speed running per min (HSR), and collisions per min (Coll) were expressed relative to BiP periods and over the whole match (>60min). Whole match metrics were significantly lower than all BiP metrics (p<0.001). Mean and max BiP HML, (p<0.01) and HSR (p<0.05) were significantly higher for backs versus forwards, whereas Coll were significantly higher for forwards (p<0.001). In plays lasting 61s or greater, max BiP mmin -1 were higher for backs. Max BiP mmin -1 , HML, HSR and Coll were all time dependant (p<0.05) showing that both movement metrics and collision demands differ as length of play continues. This study uses a novel method of accurately assessing the BiP demands of rugby union. It also reports typical and maximal demands of international rugby union that can be used by practitioners and scientists to target training of worst-case scenario's equivalent to international intensity. Backs covered greater distances at higher speeds and demonstrated higher HML, in general play as well as 'worst case scenarios'; conversely forwards perform a higher number of collisions. Copyright © 2018 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Simulation of projected water demand and ground-water levels in the Coffee Sand and Eutaw-McShan aquifers in Union County, Mississippi, 2010 through 2050

USGS Publications Warehouse

Hutson, Susan S.; Strom, E.W.; Burt, D.E.; Mallory, M.J.

2000-01-01

Ground water from the Eutaw-McShan and the Coffee Sand aquifers is the major source of supply for residential, commercial, and industrial purposes in Union County, Mississippi. Unbiased, scientifically sound data and assessments are needed to assist agencies in better understanding and managing available water resources as continuing development and growth places more stress on available resources. The U.S. Geological Survey, in cooperation with the Tennessee Valley Authority, conducted an investigation using water-demand and ground-water models to evaluate the effect of future water demand on groundwater levels. Data collected for the 12 public-supply facilities and the self-supplied commercial and industrial facilities in Union County were used to construct water-demand models. The estimates of water demand to year 2050 were then input to a ground-water model based on the U.S. Geological Survey finite-difference computer code, MODFLOW. Total ground-water withdrawals for Union County in 1998 were estimated as 2.85 million gallons per day (Mgal/d). Of that amount, municipal withdrawals were 2.55 Mgal/d with about 1.50 Mgal/d (59 percent) delivered to residential users. Nonmunicipal withdrawals were 0.296 Mgal/d. About 80 percent (2.27 Mgal/d) of the total ground-water withdrawal is produced from the Eutaw-McShan aquifer and about 13 percent (0.371 Mgal/d) from the Coffee Sand aquifer. Between normal- and high-growth conditions, total water demand could increase from 72 to 131 percent (2.9 Mgal/d in 1998 to 6.7 Mgal/d in year 2050) with municipal demand increasing from 77 to 146 percent (2.6 to 6.4 Mgal/d). Increased pumping to meet the demand for water was simulated to determine the effect on water levels in the Coffee Sand and Eutaw- McShan aquifers. Under baseline-growth conditions, increased water use by year 2050 could result in an additional 65 feet of drawdown in the New Albany area below year 2000 water levels in the Coffee Sand aquifer and about 120 feet of maximum drawdown in the Eutaw-McShan aquifer. Under normal-growth conditions, increased water use could result in an additional 65 feet of drawdown in the New Albany area below year 2000 water levels in the Coffee Sand aquifer and about 135 feet of maximum drawdown in the Eutaw-McShan aquifer. Under high-growth conditions, increased water use could result in 75 feet of drawdown in the New Albany area below year 2000 water levels in the Coffee Sand aquifer and about 190 feet of maximum drawdown in the Eutaw-McShan aquifer. The resulting highgrowth projected water level for the year 2050 at the center of the drawdown cone in the New Albany area is between 450 and 500 feet above the top of the Eutaw-McShan aquifer.

Behavior of myclobutanil, propiconazole, and nuarimol residues during lager beer brewing.

PubMed

Navarro, Simón; Pérez, Gabriel; Vela, Nuria; Mena, Luis; Navarro, Ginés

2005-11-02

Over a 4 month brewing process, the fate of three fungicides, myclobutanil, propiconazole, and nuarimol, was studied in the spent grain, brewer wort, and final beer product. Only the residual level of myclobutanil after the mashing step was higher than its maximum residue limit (MRL) on barley. A substantial fraction was removed with the spent grain in all cases (26-42%). The half-life times obtained for the fungicides during storage of the spent grains ranged from 82 to 187 days. No significant influence of the boiling stage on the decrease of the fungicide residues was demonstrated. During fermentation, the content reduction varied from 20 to 47%. After the lagering and filtration steps, no significant decrease (<10%) was observed in any of the residues. Finally, during storage of the beer (3 months), the amounts of fungicides fell by 25-50% of their respective concentrations in the finished beer.

Safe apples for baby-food production: survey of pesticide treatment regimes leaving minimum residues.

PubMed

Ticha, Jana; Hajslova, Jana; Kovalczuk, Tomas; Jech, Martin; Honzicek, Jiri; Kocourek, Vladimir; Lansky, Miroslav; Kloutvorova, Jana; Falta, Vladan

2007-06-01

A total of 19 pesticide preparations were used according to agricultural practice in six trials in apple orchards. Using gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-tandem mass spectrometry (LC-MS/MS), premature Golden Delicious apples collected 64, 50, 36 days before harvest and mature fruit were examined for residues of active ingredients. No residues of triflumuron, triazamate, chlorpyrifos, etofenprox, fenoxycarb, kresoxim-methyl, cyprodinyl, difenoconazole or thiram were detected in the first sampling. Also, the levels of chlorpyrifos-methyl, penconazole, tebuconazole and tolylfluanid dropped during the pre-harvest interval. Detectable residues of pyridaben, thiacloprid, trifloxystrobin and tetraconazole in harvested fruits were below 0.01 mg kg(-1), which is the maximum concentration of residues acceptable by baby-food producers in any raw material. The only residues exceeding this concentration were captan and teflubenzuron. Based on the data, farmers can choose pesticides for optimal treatment of plants, while enabling growth of a safe crop suitable for baby-food production.

Residue depletion of tilmicosin in chicken tissues.

PubMed

Zhang, Yue; Jiang, Haiyang; Jin, Xingjun; Shen, Zhangqi; Shen, Jianzhong; Fu, Caixia; Guo, Junlin

2004-05-05

A high-performance liquid chromatography (HPLC) method with detection at 290 nm was modified and validated for the determination of tilmicosin residues in broiler chicken tissues. The limits of detection (LOD) of the method were 0.01 microg/g for muscle and 0.025 microg/g for liver and kidney. Average recoveries ranged from 80.4 to 88.3%. Relative standard deviation values ranged from 5.2 to 12.1%. Residue depletion of tilmicosin in broiler chickens was examined after dosing over a 5-day period by incorporation of the drug into drinking water at 37.5 and 75.0 mg/L. Tilmicosin concentrations in liver and kidney were highest on day 3 of medication and on day 5 in muscle, in both low- and high-dose groups. The residue levels in both groups were significantly higher in liver than in kidney or muscle. A minimum withdrawal time of 9 days was indicated for residue levels in muscle, liver, and kidney tissues below the maximum residue level (MRL).

Pesticide residues in orange fruit from citrus orchards in Nuevo Leon State, Mexico.

PubMed

Suárez-Jacobo, Angela; Alcantar-Rosales, Victor Manuel; Alonso-Segura, Diana; Heras-Ramírez, Maria; Elizarragaz-De La Rosa, Dalau; Lugo-Melchor, Ofelia; Gaspar-Ramirez, Octavio

2017-09-01

Some international organisations established maximum residue limits (MRLs) in food to protect human health. Mexico lacks regulations in this matter, affecting national and international trade from agroindustry. The aim of this study was to diagnose pesticide residues in oranges from Nuevo Leon, México, in citrus orchards. In May 2014, 100 orange fruit samples were taken randomly from orchards and subjected to analysis for 93 pesticides at residual level by GC/QQQ-MS and LCQ-TOF-MS. Results showed the presence of 15 pesticide residues in the samples. The comparison of the residual levels of pesticides found in orange samples among the MRLs allowed by USA, EU and Japanese regulations demonstrated that all samples were below MRLs issued by USA and Japan. Some orange samples were above MRLs issued by the EU. This provides a basis to establish strategies in order to satisfy International Standards to protect human health and encourage Food Safety in Mexico.

Residues of organochlorine and synthetic pyrethroid pesticides in honey, an indicator of ambient environment, a pilot study.

PubMed

Malhat, Farag M; Haggag, Mohamed N; Loutfy, Naglaa M; Osman, Mohamed A M; Ahmed, Mohamed Tawfic

2015-02-01

Samples of honey were screened to monitor residues of organochlorine and pyrethroid pesticides. The study meant to examine the quality of honey, and to use honey as a bioindicator of environmental contamination. Residue levels were determined by gas chromatography (GC-μECD). Samples had a wide spectrum of organochlorine and synthetic pyrethroids pesticides, with hexachlorobenzene (HCB) as the most frequently detected organochlorine, followed by permethrin, heptachlor epoxide. Only one sample had a concentration of γ-HCH higher than maximum residue limit of honey (0.01 mg kg(-1)). Residues of organochlorines detected, indicate the presence of some fresh supplies, despite the ban imposed on their use. The study confirmed that honey bee and beehive matrices could be used as gauge for monitoring environment contamination. From public health point of view, the observed levels of pesticide residues in honey do not pose a serious health risk to the consumers, but raises questions of the source of organochlorines. Copyright © 2014 Elsevier Ltd. All rights reserved.

Transfer of nitroimidazoles from contaminated beeswax to honey.

PubMed

Mitrowska, Kamila; Antczak, Maja

2017-04-01

Nitroimidazoles are not authorised for the treatment of honey bees in the European Union. However, they can be found in honey largely because they are illegally used in apiculture for the treatment of Nosema. The aim of the study was to examine the possible transfer of nitroimidazoles (metronidazole, ronidazole, dimetridazole and ipronidazole) from contaminated beeswax to honey. The wax foundations fortified with a mixture of four nitroimidazoles at three concentration levels (1000, 10,000 and 100,000 μg kg - 1 ) were placed in beehives to let the honeybees (Apis mellifera L.) draw out the contaminated wax foundations to honeycombs. At 1 month from the start, the frames filled with capped honey were removed from the hives for a first sampling of honey. Next, the honeycombs were further incubated for 5 months in the laboratory at 35°C and sampled monthly. In the sampled honey, the concentrations of nitroimidazoles and their main metabolites (hydroxymetronidazole, 2-hydroxymethyl-1-methyl-5-nitroimidazole, hydroxyipronidazole) were determined by LC-MS/MS and compared with those determined in the nitroimidazole-containing wax foundations. Each of the tested nitroimidazoles could migrate from beeswax to honey kept in the contaminated combs at each tested concentration level. Higher maximum concentrations of residues in honey sampled from contaminated combs at 1000, 10,000 and 100,000 μg kg - 1 were observed for metronidazole (28.9, 368.5 and 2589.4 μg kg - 1 respectively) and ronidazole (27.4, 232.9 and 2351.2 μg kg - 1 respectively), while lower maximum concentrations were measured for dimetridazole (0.98, 8.4 and 67.7 μg kg - 1 ) and ipronidazole (0.9, 7.9 and 35.7 μg kg - 1 respectively). When we took into account that a frame completely filled with honey on both sides of the comb contained 110 g of beeswax and 2488 g of honey, and that this ratio was constant, then maximum amounts of initial metronidazole, ronidazole, dimetridazole and ipronidazole that migrated from contaminated wax foundations to honey could be calculated: 65-89%, 55-63%, 1.7-2.7% and 1.4-2.3%, respectively.

Food Safety is an Important Public Health Issue: Chloramphenicol Residues Determination by Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS) in honey.

PubMed

Krivohlavek, Adela; Žuntar, Irena; Ivešić, Martina; Andačić, Ivana Mandić; Šikić, Sandra

2014-12-01

Honey is used for nutritional, medicinal and industrial purposes and antibiotic residues may harm its quality and constitute a danger to human health. The broad spectrum antibiotic chloramphenicol (CAP) was used for curative purposes in veterinary medicine, but is now forbidden in European Union (EU) because of its many serious side effects (e.g. aplastic anaemia, grey syndrome, severe bone marrow depression and hypersensitivity). The aim of this study was to facilitate analyses of the quality and safety of Croatian honey distributed to whole European Union market; an assessment that has not previously been made. CAP in honey was qualifying and quantifying by validated liquid chromatography tandem mass spectrometry with negative electrospray ionisation method (LC-MS/MS). The target antibiotic was separated on chromatographic column Zorbax SB C18 (150 mm x 2.1 mm, 3.5 μm) with a gradient elution using acetonitrile - 0.1% formic acid mobile phase at a flow rate of 0.3 mL/min, with column temperature 35°C for CAP and 5D-CAP as internal standard. Homogenised honey samples were diluted with acetate buffer solution and extracted on Oasis Hydrophilic-Lipophilic-Balanced (HLB) sorbents. The method was used to analyse 280 domestic honey samples collected throughout Croatia between 2005.-2013. Recoveries of the method for real (acacia, chestnut, linden and flower) honey samples were 102% with RSD 8.4%. The value CCα and CCβ were 0.09 and 0.12 μg/kg, respectively. Results showed only three subsequent positive detections (1.1%) of CAP in honey. Analysed honey samples from Croatia showed good quality and safety what is the one of the main objective in consumer health policy in EU.

JPRS Report, Soviet Union, Foreign Military Review, No. 5, May 1987

DTIC Science & Technology

1987-09-18

which can carry up to 16 Hellfire missiles with semi-active laser homing devices (maximum range of 6,000 m). The presence of good flight and technical...will have laser -guided control systems, that is, will retain the link between the missile and the launch installation right up to impact on target as...antitank missile system to replace the Milan system in the 1990s. The control system with a laser -guided homing device also has been accepted for

Seismic performance of the typical RC beam-column joint subjected to repeated earthquakes

NASA Astrophysics Data System (ADS)

Hassanshahi, Omid; Majid, Taksiah A.; Lau, Tze Liang; Yousefi, Ali; Tahara, R. M. K.

2017-10-01

It is common that a building experience repeated earthquakes throughout its lifetime. Such earthquake is capable of creating severe damage in primary elements of the building due to accumulation of inelastic displacement from repetition. The present study focuses on the influence of repeated earthquakes on a typical Reinforced Concrete (RC) beam-column joint, especially on the maximum inelastic displacement demand and maximum residual displacement. For this purpose, the capability of nonlinear modelling in simulating the hysteretic behaviour of the prototype experimental specimen is first determined using RUAUMOKO. A nonlinear Incremental Dynamic Analysis (IDA) on the verified model is then carried out in order to estimate with maximum accuracy the ultimate load bearing capacity to progressive collapse of the RC joint under investigation. Twenty ground motions are selected, and single (C1), double (C2), and triple (C3) event of synthetic repeated earthquakes are then considered. The results show that the repeated earthquakes significantly increase the inelastic demand of the RC joint. On average, relative increment of maximum inelastic displacement demand is experienced about 28.9% and 39.4% when C2 and C3 events of repeated earthquakes are induced, respectively. Residual displacements for repeated earthquakes are also significantly higher than that for single earthquakes.

[Finite element analysis of the stress distribution of two-piece post crown with different adhesives ].

PubMed

He, Lihui; Liu, Lijie; Gao, Bei; Gao, Shang; Chen, Yifu; Zhihui, Liu

2013-08-01

To establish three-dimensional finite element model of two-piece post crown to the mandibular first molar residual roots, and analyze the stress distribution characteristic to the residual roots with different adhesives, so as to get the best combination under different conditions. The complete mandibular first molar in vitro was selected, the crown was removed along the cemento-enamel junction, then the residual roots were scanned by CT. CT images were imported into a reverse engineering software, and the three-dimensional finite element model of the mandibular first molar residual roots was reconstructed. Titanium two-piece post crown of the mandibular first molar residual roots was produced, then was scanned by CT. The model was reconstructed and assembled by MIMICS. The stress distribution of the root canal and root section under the vertical load and lateral load with different bonding systems were analyzed. Three-dimensional finite element model of two-piece post crown to the mandibular first molar residual roots was established. With the increasing of elastic modulus of the adhesives, the maximum stress within the root canal was also increasing. Elastic modulus of zinc phosphate was the biggest, so the stress within the root canal was the biggest; elastic modulus of Superbond C&B was the smallest, so the stress within the root canal was the smallest. Lateral loading stress was much larger than the vertical load. Under vertical load, the load on the root section was even with different bonding systems. Under lateral load, the maximum stress was much larger than the vertical load. The stress on the root section was minimum using zinc phosphate binder, and the stress on the root section was maximum using Superbond C&B. In two-piece post crown restorations, there is significant difference between different adhesives on tooth protection. When the tooth structure of the root canal orifices is weak, in order to avoid the occurrence of splitting, the larger elastic modulus bonding system is the first choice, such as zinc phosphate binder. When the resistance form of the root canal orifices is good enough but the root is too weak, it is suggested that the smaller elastic modulus bonding system is the first choice, such as Superbond C&B.

Through-Thickness Residual Stress Profiles in Austenitic Stainless Steel Welds: A Combined Experimental and Prediction Study

NASA Astrophysics Data System (ADS)

Mathew, J.; Moat, R. J.; Paddea, S.; Francis, J. A.; Fitzpatrick, M. E.; Bouchard, P. J.

2017-12-01

Economic and safe management of nuclear plant components relies on accurate prediction of welding-induced residual stresses. In this study, the distribution of residual stress through the thickness of austenitic stainless steel welds has been measured using neutron diffraction and the contour method. The measured data are used to validate residual stress profiles predicted by an artificial neural network approach (ANN) as a function of welding heat input and geometry. Maximum tensile stresses with magnitude close to the yield strength of the material were observed near the weld cap in both axial and hoop direction of the welds. Significant scatter of more than 200 MPa was found within the residual stress measurements at the weld center line and are associated with the geometry and welding conditions of individual weld passes. The ANN prediction is developed in an attempt to effectively quantify this phenomenon of `innate scatter' and to learn the non-linear patterns in the weld residual stress profiles. Furthermore, the efficacy of the ANN method for defining through-thickness residual stress profiles in welds for application in structural integrity assessments is evaluated.

Dissipation dynamic, residue distribution and processing factor of hexythiazox in strawberry fruits under open field condition.

PubMed

Saber, Ayman N; Malhat, Farag M; Badawy, Hany M A; Barakat, Dalia A

2016-04-01

Two independent field trials were performed to investigate the dissipation and residue levels of hexythiazox in strawberry. The study presents a method validation for extraction and quantitative analysis of hexythiazox residues in strawberry using HPLC-DAD. The results shown that the mean recoveries ranged from 85% to 93%, furthermore the intra- and inter-day relative standard deviations were less than 10%. The results suggest that the hexythiazox dissipation curves followed the first-order kinetic and its half-life ranged from 3.43 to 3.81 days. The final residues in strawberry were below the Codex maximum residue limit (MRL) (6 mg/kg) after three days of the application. The effects of household processing and storage on the levels of hexythiazox residues were quantified, and it's useful for reducing the dietary exposure. The processing factor after each stage were generally less than 1, indicating that the whole process can reduce the residues of hexythiazox in strawberry. The results could provide guidance to safe and reasonable use of hexythiazox in agriculture. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pyrolysis and reutilization of plant residues after phytoremediation of heavy metals contaminated sediments: For heavy metals stabilization and dye adsorption.

PubMed

Gong, Xiaomin; Huang, Danlian; Liu, Yunguo; Zeng, Guangming; Wang, Rongzhong; Wei, Jingjing; Huang, Chao; Xu, Piao; Wan, Jia; Zhang, Chen

2018-04-01

This study aimed to investigate the effect of pyrolysis on the stabilization of heavy metals in plant residues obtained after phytoremediation. Ramie residues, being collected after phytoremediation of metal contaminated sediments, were pyrolyzed at different temperatures (300-700 °C). Results indicated that pyrolysis was effective in the stabilization of Cd, Cr, Zn, Cu, and Pb in ramie residues by converting the acid-soluble fraction of metals into residual form and decreasing the TCLP-leachable metal contents. Meanwhile, the reutilization potential of using the pyrolysis products generated from ramie residues obtained after phytoremediation as sorbents was investigated. Adsorption experiments results revealed that the pyrolysis products presented excellent ability to adsorb methylene blue (MB) with a maximum adsorption capacity of 259.27 mg/g. This study demonstrated that pyrolysis could be used as an efficient alternative method for stabilizing heavy metals in plant residues obtained after phytoremediation, and their pyrolysis products could be reutilized for dye adsorption. Copyright © 2018 Elsevier Ltd. All rights reserved.

Photoacoustic Spectroscopy as a Non-destructive Tool for Quantification of Pesticide Residue in Apple Cuticle

NASA Astrophysics Data System (ADS)

Liu, Lixian; Wang, Yafei; Gao, Chunming; Huan, Huiting; Zhao, Binxing; Yan, Laijun

2015-06-01

Photoacoustic spectroscopy (PAS), the non-destructive method to detect residue of dimethyl-dichloro-vinyl-phosphate (DDVP) pesticide in a cuticle of apple, is described. After constructing the PA experimental setup and identifying three characteristic peaks of DDVP in the near ultraviolet region, the PA spectra of an apple cuticle contaminated with DDVP were collected. The artificial neural network method was then applied to analyze data quantitatively. The results show a correlation coefficient exceeding 0.99 and a detection limit of 0.2 ppm, which is within the national food safety standard for maximum residue limits for pesticides in food (GB 2763-2012). This fact and the non-destructive character of PAS make the approach promising for detection of pesticide residue in fruits.

Method and apparatus for in-situ detection and isolation of aircraft engine faults

NASA Technical Reports Server (NTRS)

Bonanni, Pierino Gianni (Inventor); Brunell, Brent Jerome (Inventor)

2007-01-01

A method for performing a fault estimation based on residuals of detected signals includes determining an operating regime based on a plurality of parameters, extracting predetermined noise standard deviations of the residuals corresponding to the operating regime and scaling the residuals, calculating a magnitude of a measurement vector of the scaled residuals and comparing the magnitude to a decision threshold value, extracting an average, or mean direction and a fault level mapping for each of a plurality of fault types, based on the operating regime, calculating a projection of the measurement vector onto the average direction of each of the plurality of fault types, determining a fault type based on which projection is maximum, and mapping the projection to a continuous-valued fault level using a lookup table.

Longitudinal residual stresses in boron fibers

NASA Technical Reports Server (NTRS)

Behrendt, D. R.

1976-01-01

A method of measuring the longitudinal residual stress distribution in boron fibers is presented. The residual stresses in commercial CVD boron on tungsten fibers of 102, 142, and 203 microns (4, 5.6, and 8 mil) diameters were determined. Results for the three sizes show a compressive stress at the surface 800 to -1400 MN/sq m 120 to -200 ksi), changing monotonically to a region of tensile stress within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile 600 to 1000 MN/sq m(90 to 150 ksi) and then decreases to compressive near the tungsten boride core. The core itself is under a compressive stress of approximately -1300 MN/sq m (-190 ksi). The effects of surface removal on core residual stress and core-initiated fracture are discussed.

Effect of residual stresses induced by prestressing on rolling element fatigue life

NASA Technical Reports Server (NTRS)

Parker, R. J.; Zaretsky, E. V.

1972-01-01

A mechanical prestress cycle suitable to induce compressive stress beneath the surface of the inner race of radially loaded 207-size bearings was determined. Compressive residual stress in excess 0.69 x 10 to the 9th power N/sq m (100,000 psi), as measured by X-ray diffraction, were induced at the depth of maximum shearing stress. The prestress cycle consisted of running the bearings for 25 hours at 2750 rpm at a radial load which produced a maximum Hertz stress of 3.3 x 10 to the 9th power N/sq m (480,000 psi) at the contact of the inner race and the heaviest loaded ball. Bearings subjected to this prestress cycle and subsequently fatigue tested gave a 10 percent fatigue life greater than twice that of a group of baseline bearings.

Dynamics of storage of organochlorine pollutants in herring gulls

USGS Publications Warehouse

Anderson, D.W.; Hickey, J.J.

1976-01-01

Several organochlorine pollutants were studied over the period of one annual cycle in caged juvenile and wild-collected adult herring gulls (Lagus argentatus) from Lake Michigan. Fish, mostly alewives (Alosa pseudoharengus), comprised the major year-round food items in the wild; alewives were also fed to the caged juveniles. Fish residues averaged around 3 mg/kg of p,p'-DDE, 2 mg/kg p,p'DDT + p,p'-TDE, and 2 mg/kg apparent PCBs. Juvenile body-burdens of DDE and PCBs showed a continual buildup after fledging, then a temporary dynamic equilibrium, related only in part to annual lipid deposition. Maximum body-burdens were reached in both juveniles and adults when winter fat deposits were declining prior to the breeding season?followed by a return to dynamic equilibrium. Residues of DDT and TDE followed closely the annual pattern of lipid deposition in both juveniles and adults. Total body-burdens in both age classes were similar after the buildups to equilibrium in juveniles in their eighth month after fledging. Seasonal variations of residues of DDE and PCBs were characterised by two phases in adults and three in juveniles, which gradually assumed the adult cyclic pattern. The maximum body-burdens attained by caged juveniles fed a diet of Lake Michigan alewives were 290 mg/kg DDE, 19 mg/kg DDT + TDE, and 200 mg/kg apparent PCBs. Residues in wild adults at the same time were 300, 4, and 200 mg/kg of the same residues. Apparent PCBs and DDE were highly accumulative, although DDE levels resulted from dietary DDE, as well as conversion from DDT.

40 CFR 180.505 - Emamectin; tolerances for residues.

Code of Federal Regulations, 2011 CFR

2011-07-01

... residues of emamectin (a mixture of a minimum of 90% 4′-epi-methylamino-4′-deoxyavermectin B1a and maximum of 10% 4′-epi-methylamino-4′-deoxyavermectin B1b) and its metabolites 8,9-isomer of the B1a and B1b component of the parent (8,9-ZMA), or 4′-deoxy-4′-epi-amino-avermectin B1a and 4′-deoxy-4′-epi-amino...

Long-term therapeutic efficacy of photo-selective vaporization of prostate

NASA Astrophysics Data System (ADS)

Arum, Carl-Jørgen; Muller, Camilla; Romundstad, Pal; Stokkan, Inger; Mjønes, Jan

2010-02-01

OBJECTIVES: We evaluated the long term therapeutic efficacy of 80 watt photo-selective vaporization of the prostate (PVP) in patients suffering from lower urinary tract symptoms (LUTS) secondary to prostatic obstruction. MATERIAL & METHODS: 150 unselected patients at the average age 73 (range 51-92) and a mean American Society of Anesthesiologists score of 2.4 (median 2.0), of whom 33% were medicated with acetylsalicylic acid and 5% were anticoagulated with warfarin. Inclusion/exclusion criteria were the same as for TUR-P at our institution. First patient was operated March 2004 and yearly follow-up of all patients has been attempted for 5 years. Follow-up variables have included yearly creatinine, PSA, IPSS, ØOL, post-void residual urin and maximum/average urine flow rate. RESULTS: At 12 and 24 months postoperatively, the following parameters were significantly (p<0.001) improved: trans-rectal ultrasound, international prostate symptom score, quality of life score, post-void residual urine volume, flow max/average, opening pressure, pressure @ flow-max, and micturition resistance. At 48 and 60 months creatinine, PSA, IPSS, ØOL, post-void residual urin and maximum/average urine flow rates were still significantly (p<0.001) improved compared to pre-operative values. CONCLUSION: Up to 5 year follow-up reveals that 80 watt PVP provides significant and stable symptom relief as well as objective improvement in residual urine and flowmetric outcomes.

Degradation of chlorpyrifos residues in apple under temperate conditions of Kashmir Valley.

PubMed

Mukhtar, Malik; Sherwani, Asma; Wani, Ashraf Alam; Ahmed, Sheikh Bilal; Sofi, Javid Ahmad; Bano, Parveena

2015-08-01

The present studies were carried out to observe the dissipation pattern of chlorpyrifos on apple in Kashmir Valley. Persistence of chlorpyrifos in apple was studied following two applications rates of chlorpyrifos (Dursban 20 EC) at 200 g a.i. ha(-1) (single dose T 1) and 400 g a.i. ha(-1) (double dose T 2). The average initial deposit of chlorpyrifos was found to be 1.61 and 1.98 μg g(-1) for T 1 and T 2 application rates respectively on apple. The residues dissipated to 0.09 and 0.06 μg g(-1) after 15- and 30-day post treatment with half-life periods of 3.34 and 5.47 days in T 1 and T 2 application rates, respectively. The residues of chlorpyrifos dissipated to below limit of quantification (LOQ) of 0.04 μg g(-1) after 30 day at T 1 application rate. A waiting period of 6 days must be observed for chlorpyrifos on apple at recommended application rate for the safety of consumers. Theoretical maximum residue contribution (TMRC) values were found to be far less than maximum permissible intake (MPI) at 0 day in both the dosages suggesting chlorpyrifos on apple in Kashmir is unlikely to cause health risks.

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India.

PubMed

Kotinagu, Korrapati; Krishnaiah, Nelapati

2015-04-01

The present study was conducted to find the organochlorine pesticide (OCP) and organophosphorus pesticide (OPP) residues in fodder and milk samples along Musi river belt, India. Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077). Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167). The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL) values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX.

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India

PubMed Central

Kotinagu, Korrapati; Krishnaiah, Nelapati

2015-01-01

Aim: The present study was conducted to find the organochlorine pesticide (OCP) and organophosphorus pesticide (OPP) residues in fodder and milk samples along Musi river belt, India. Materials and Methods: Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. Results: The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077). Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167). The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. Conclusion: The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL) values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX. PMID:27047132

Occurrence and estimation of pesticide residues in edible minor crops in southeastern Poland in 2013-2014.

PubMed

Podbielska, Magdalena; Szpyrka, Ewa; Matyaszek, Aneta; Słowik-Borowiec, Magdalena; Rupar, Julian; Kurdziel, Anna

2016-07-01

This paper presents the results of official control of pesticide residues in minor crops collected in southeastern Poland in 2013-2014. Compliance of used pesticides with applicable law was also verified, and determined residues were compared to maximum residue levels (MRLs) provided for in Regulation (EC) No. 395/2005. A total of 583 samples of 25 different types of fresh fruit and vegetables were analyzed for pesticide residues. Pesticide residues were detected in 158 samples (27.1 % of the analyzed samples). According to the European Commission Health & Consumer Protection Directorate-General (SANCO) guidelines document, MRL violations were understood as cases where a residue level exceeded the MRL after the uncertainty of the method (50 %) was considered. MRL violations were found in four samples. The usage of unauthorized pesticides was detected in 5.8 % of analyzed samples. Substances banned in Poland were found in two samples. Fungicides were the most frequently detected group of pesticides. Pesticide residues were most commonly found in fruit samples (19.4 % of all analyzed samples), mainly in gooseberry, redcurrant, and huckleberry. The majority of samples were compliant with MRLs, which means that they were suitable for trade.

Evolution of titanium residue on the walls of a plasma-etching reactor and its effect on the polysilicon etching rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirota, Kosa, E-mail: hirota-kousa@sme.hitachi-hitec.com; Itabashi, Naoshi; Tanaka, Junichi

2014-11-01

The variation in polysilicon plasma etching rates caused by Ti residue on the reactor walls was investigated. The amount of Ti residue was measured using attenuated total reflection Fourier transform infrared spectroscopy with the HgCdTe (MCT) detector installed on the side of the reactor. As the amount of Ti residue increased, the number of fluorine radicals and the polysilicon etching rate increased. However, a maximum limit in the etching rate was observed. A mechanism of rate variation was proposed, whereby F radical consumption on the quartz reactor wall is suppressed by the Ti residue. The authors also investigated a plasma-cleaningmore » method for the removal of Ti residue without using a BCl{sub 3} gas, because the reaction products (e.g., boron oxide) on the reactor walls frequently cause contamination of the product wafers during etching. CH-assisted chlorine cleaning, which is a combination of CHF{sub 3} and Cl{sub 2} plasma treatment, was found to effectively remove Ti residue from the reactor walls. This result shows that CH radicals play an important role in deoxidizing and/or defluorinating Ti residue on the reactor walls.« less

Minimization of Residual Stress in an Al-Cu Alloy Forged Plate by Different Heat Treatments

NASA Astrophysics Data System (ADS)

Dong, Ya-Bo; Shao, Wen-Zhu; Jiang, Jian-Tang; Zhang, Bao-You; Zhen, Liang

2015-06-01

In order to improve the balance of mechanical properties and residual stress, various quenching and aging treatments were applied to Al-Cu alloy forged plate. Residual stresses determined by the x-ray diffraction method and slitting method were compared. The surface residual stress measured by x-ray diffraction method was consistent with that measured by slitting method. The residual stress distribution of samples quenched in water with different temperatures (20, 60, 80, and 100 °C) was measured, and the results showed that the boiling water quenching results in a 91.4% reduction in residual stress magnitudes compared with cold water quenching (20 °C), but the tensile properties of samples quenched in boiling water were unacceptably low. Quenching in 80 °C water results in 75% reduction of residual stress, and the reduction of yield strength is 12.7%. The residual stress and yield strength level are considerable for the dimensional stability of aluminum alloy. Quenching samples into 30% polyalkylene glycol quenchants produced 52.2% reduction in the maximum compressive residual stress, and the reduction in yield strength is 19.7%. Moreover, the effects of uphill quenching and thermal-cold cycling on the residual stress were also investigated. Uphill quenching and thermal-cold cycling produced approximately 25-40% reduction in residual stress, while the effect on tensile properties is quite slight.

Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait.

PubMed

Jallow, Mustapha F A; Awadh, Dawood G; Albaho, Mohammed S; Devi, Vimala Y; Ahmad, Nisar

2017-07-25

The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS) or liquid chromatography-tandem mass spectrometry (LC - MS / MS). Pesticide residues above the maximum residue limits (MRL) were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

Evaluation of the Klobuchar model in TaiWan

NASA Astrophysics Data System (ADS)

Li, Jinghua; Wan, Qingtao; Ma, Guanyi; Zhang, Jie; Wang, Xiaolan; Fan, Jiangtao

2017-09-01

Ionospheric delay is the mainly error source in Global Navigation Satellite System (GNSS). Ionospheric model is one of the ways to correct the ionospheric delay. The single-frequency GNSS users modify the ionospheric delay by receiving the correction parameters broadcasted by satellites. Klobuchar model is widely used in Global Positioning System (GPS) and COMPASS because it is simple and convenient for real-time calculation. This model is established on the observations mainly from Europe and USA. It does not describe the equatorial anomaly region. South of China is located near the north crest of the equatorial anomaly, where the ionosphere has complex spatial and temporal variation. The assessment on the validation of Klobuchar model in this area is important to improve this model. Eleven years (2003-2014) data from one GPS receiver located at Taoyuan Taiwan (121°E, 25°N) are used to assess the validation of Klobuchar model in Taiwan. Total electron content (TEC) from the dual-frequency GPS observations is calculated and used as the reference, and TEC based on the Klobuchar model is compared with the reference. The residual is defined as the difference between the TEC from Klobuchar model and the reference. It is a parameter to reflect the absolute correction of the model. RMS correction percentage presents the validation of the model relative to the observations. The residuals' long-term variation, the RMS correction percentage, and their changes with the latitudes are analyzed respectively to access the model. In some months the RMS correction did not reach the goal of 50% purposed by Klobuchar, especially in the winter of the low solar activity years and at nighttime. RMS correction did not depend on the 11-years solar activity, neither the latitudes. Different from RMS correction, the residuals changed with the solar activity, similar to the variation of TEC. The residuals were large in the daytime, during the equinox seasons and in the high solar activity years; they are small at night, during the solstice seasons, and in the low activity years. During 1300-1500 BJT in the high solar activity years, the mean bias was negative, implying the model underestimated TEC on average. The maximum mean bias was 33TECU in April 2014, and the maximum underestimation reached 97TECU in October 2011. During 0000-0200 BJT, the residuals had small mean bias, small variation range and small standard deviation. It suggested that the model could describe the TEC of the ionosphere better than that in the daytime. Besides the variation with the solar activity, the residuals also vary with the latitudes. The means bias reached the maximum at 20-22°N, corresponding to the north crest of the equatorial anomaly. At this latitude, the maximum mean bias was 47TECU lower than the observation in the high activity years, and 12TECU lower in the low activity years. The minimum variation range appeared at 30-32°N in high and low activity years. But the minimum mean bias was at different latitudes in the high and low activity years. In the high activity years, it appeared at 30-32°N, and in the low years it was at 24-26°N. For an ideal model, the residuals should have small mean bias and small variation range. Further study is needed to learn the distribution of the residuals and to improve the model.

Why chlorate occurs in potable water and processed foods: a critical assessment and challenges faced by the food industry.

PubMed

Kettlitz, Beate; Kemendi, Gabriella; Thorgrimsson, Nigel; Cattoor, Nele; Verzegnassi, Ludovica; Le Bail-Collet, Yves; Maphosa, Farai; Perrichet, Aurélie; Christall, Birgit; Stadler, Richard H

2016-06-01

Recently, reports have been published on the occurrence of chlorate mainly in fruits and vegetables. Chlorate is a by-product of chlorinating agents used to disinfect water, and can be expected to be found in varying concentrations in drinking water. Data on potable water taken at 39 sampling points across Europe showed chlorate to range from < 0.003 to 0.803 mg l(-1) with a mean of 0.145 mg l(-1). Chlorate, however, can also be used as a pesticide, but authorisation was withdrawn in the European Union (EU), resulting in a default maximum residue limit (MRL) for foods of 0.01 mg kg(-1). This default MRL has now led to significant problems in the EU, where routinely disinfected water, used in the preparation of food products such as vegetables or fruits, leaves chlorate residues in excess of the default MRL, and in strict legal terms renders the food unmarketable. Due to the paucity of data on the chlorate content of prepared foods in general, we collated chlorate data on more than 3400 samples of mainly prepared foods, including dairy products, meats, fruits, vegetables and different food ingredients/additives. In total, 50.5% of the food samples contained chlorate above 0.01 mg kg(-1), albeit not due to the use of chlorate as a pesticide but mainly due to the occurrence of chlorate as an unavoidable disinfectant by-product. A further entry point of chlorate into foods may be via additives/ingredients that may contain chlorate as a by-product of the manufacturing process (e.g. electrolysis). Of the positive samples in this study, 22.4% revealed chlorate above 0.1 mg kg(-1). In the absence of EU levels for chlorate in water, any future EU regulations must consider the already available WHO guideline value of 0.7 mg l(-1) in potable water, and the continued importance of the usage of oxyhalides for disinfection purposes.

Identification of ethylene oxide in herbs, spices and other dried vegetables imported into Italy.

PubMed

Bononi, Monica; Quaglia, Giancarlo; Tateo, Fernando

2014-01-01

Gas chromatography-mass spectrometry was used to analyse ethylene oxide (EO) in 63 samples of dried vegetable materials for food use derived from import commodities and subjected to quality control for three food-transformation industries. EO residues were quantified through the determination of ethylene chlorohydrin (ECH). About 29% of the samples analysed contained more than 0.3 mg kg(-1) of EO. Thus, this specific analytical control limited to 20% of import aromatic matters needs to be increased. This paper demonstrates the importance of this specific control considering the banned use of microbial decontamination EO treatment in the European Union.

From Principal Component to Direct Coupling Analysis of Coevolution in Proteins: Low-Eigenvalue Modes are Needed for Structure Prediction

PubMed Central

Cocco, Simona; Monasson, Remi; Weigt, Martin

2013-01-01

Various approaches have explored the covariation of residues in multiple-sequence alignments of homologous proteins to extract functional and structural information. Among those are principal component analysis (PCA), which identifies the most correlated groups of residues, and direct coupling analysis (DCA), a global inference method based on the maximum entropy principle, which aims at predicting residue-residue contacts. In this paper, inspired by the statistical physics of disordered systems, we introduce the Hopfield-Potts model to naturally interpolate between these two approaches. The Hopfield-Potts model allows us to identify relevant ‘patterns’ of residues from the knowledge of the eigenmodes and eigenvalues of the residue-residue correlation matrix. We show how the computation of such statistical patterns makes it possible to accurately predict residue-residue contacts with a much smaller number of parameters than DCA. This dimensional reduction allows us to avoid overfitting and to extract contact information from multiple-sequence alignments of reduced size. In addition, we show that low-eigenvalue correlation modes, discarded by PCA, are important to recover structural information: the corresponding patterns are highly localized, that is, they are concentrated in few sites, which we find to be in close contact in the three-dimensional protein fold. PMID:23990764

Studies on pyrolysis and gasification of automobile shredder residue in China.

PubMed

Ni, Feijian; Chen, Ming

2014-10-01

With increasing automobile ownerships in China, the number of end-of-life vehicles has also rapidly increased. However, the automobile shredder residue generated during the dismantling of end-of-life vehicles in China is not treated properly and has caused great resource waste and environmental problems. In this work, automobile shredder residue from a domestic end-of-life vehicles dismantling company was comprehensively studied through element analysis, combustion heat experiment, proximate analysis, and thermogravimetric analysis. The feasibility of using pyrolysis combined with gasification to treat and recycle automobile shredder residue was investigated. The produced gas, oil, and residue yield was measured and the correlation between their yield and the experimental temperature and ratio of air to automobile shredder residue feed was studied. It is found that when ratio of air and experimental temperature are 1.5 mol kg(-1) and 900 °C, respectively, the heat energy of the gas produced per kilogram treated automobile shredder residue reaches a maximum value of 11.28 MJ. The characteristics of pyrolysis oil and solid residue were studied. The solid residue takes up 4.65%~5.57% of the original end-of-life vehicles weight. This greatly helps to reach the target of a 95% recycling rate. © The Author(s) 2014.

[Levels of Ochratoxin A and total Aflatoxins in Panamanian exportation coffee by an ELISA Method].

PubMed

Franco, Heriberto; Vega, Aracelly; Reyes, Stephany; De Léon, Javier; Bonilla, Alexis

2014-03-01

A study about processing conditions of exportation coffee in 15 benefits located in Chiriqui, western region of Panama, was conducted. In addition, 21 samples of processed coffee (green beans), from the benefits, were analyzed. The samples were microbiologically tested in order to quantify total aflatoxins (B1, B2, G1 and G2) and Ochratoxin A (OTA), using the immunoaffinity ELISA method. A detection limit of 0.017 ng/mL, was determined for Ochratoxin A, which is equivalent to a concentration of 0.829 µg/kg, and a detection limit of 0.027 ng/mL, for total aflatoxins, which is equivalent to a concentration of 1.350 µg/kg. It was found that four (19%) out of the 21 samples were positive to the presence of Ochratoxin A and three (14%) to the presence of total aflatoxins. Samples showed levels of Ochratoxin A in the range 4.90 - 37.73 µg/kg; only three of them exceeded the maximum limit allowed by the European Union, for the concentration of Ochratoxin, which is of 5.0 µg/kg. Total aflatoxins were found in the range 1.51 - 1.93 µg/kg, below 10 µg/kg which is the maximum limit allowed for coffee by the European Union. The results indicate that the processing of coffee produced in Panama successfully meets international standards for postharvest handling, which leads to a low incidence ofmycotoxins and very low levels ofmycotoxin-producing fungi.

The effect of net charge on the solubility, activity, and stability of ribonuclease Sa.

PubMed

Shaw, K L; Grimsley, G R; Yakovlev, G I; Makarov, A A; Pace, C N

2001-06-01

The net charge and isoelectric pH (pI) of a protein depend on the content of ionizable groups and their pK values. Ribonuclease Sa (RNase Sa) is an acidic protein with a pI = 3.5 that contains no Lys residues. By replacing Asp and Glu residues on the surface of RNase Sa with Lys residues, we have created a 3K variant (D1K, D17K, E41K) with a pI = 6.4 and a 5K variant (3K + D25K, E74K) with a pI = 10.2. We show that pI values estimated using pK values based on model compound data can be in error by >1 pH unit, and suggest how the estimation can be improved. For RNase Sa and the 3K and 5K variants, the solubility, activity, and stability have been measured as a function of pH. We find that the pH of minimum solubility varies with the pI of the protein, but that the pH of maximum activity and the pH of maximum stability do not.

Adsorption performance of creatinine on dialdehyde nanofibrillated cellulose derived from potato residues.

PubMed

Cui, Dongli; Liu, Zehua; Yang, Yaxing; Huang, Rijin; Cheng, Xiaojuan; Fatehi, Pedram; Sun, Bo

2016-01-01

Potato residue is vastly produced in the food industry but it is landfilled. This article describes the treatment of purified cellulose derived from potato residues by a high pressure homogenizer to produce nano-fibrillated cellulose (NFC), which was then oxidized by sodium periodate to prepare dialdehyde nano-fibrillated cellulose (DANFC). The produced NFC and DANFC were characterized by a scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The orthogonal experiment was induced to obtain the maximum degree of oxidation (DO) on DANFC. The results indicated that the optimal conditions were 40°C and pH 3. Alternatively, the isotherm and kinetic studies for the adsorption of creatinine on DANFC with different DOs (70.5 and 88.8%) were investigated, and the experimental results fitted well into Freundlich isotherm model and pseudo second-order kinetic model. The maximum adsorption capacities of DANFCs with the DO of 70.55 and 88.85% were 6.7 and 17.2 mg g(-1) , respectively, which were achieved under the conditions of 37°C and initial creatinine concentration of 100 mg L(-1). © 2015 American Institute of Chemical Engineers.

Antimicrobials in beekeeping.

PubMed

Reybroeck, Wim; Daeseleire, Els; De Brabander, Hubert F; Herman, Lieve

2012-07-06

The bee diseases American and European foulbrood and nosemosis can be treated with anti-infectious agents. However, in the EU and the USA the use of these agents in beekeeping is strictly regulated due to the lack of tolerance (e.g. Maximum Residue Limit) for residues of antibiotics and chemotherapeutics in honey. This article reviews the literature dealing with antimicrobials of interest in apiculture, stability of these antimicrobials in honey, and disposition of the antimicrobials in honeybee hives. Copyright © 2012 Elsevier B.V. All rights reserved.

Disappearance of six pesticides in fresh and processed zucchini, bioavailability and health risk assessment.

PubMed

Oliva, J; Cermeño, S; Cámara, M A; Martínez, G; Barba, A

2017-08-15

A field study was carried out on the dissipation of three insecticides and three fungicides during the freezing of zucchini. A simultaneous residue analysis method is validated using QuEChERS extraction with acetonitrile and CG-MS and LC-MS analysis. The residues detected after field application never exceeded the established maximum residue limits. The processing factors calculated (fresh product/frozen product) are lower than 1, indicating a clear influence of the stages of the freezing process, especially the washing and blanching. The in vitro study of bioavailability establishes a low percentage of stomach absorption capacity. The level of residues detected in fresh zucchini and the Estimated Daily Intake calculated for Spain suggest that there is no risk of acute toxicity due to dietary exposure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhancement of methylbenzene adsorption capacity through cetyl trimethyl ammonium bromide-modified activated carbon derived from Astragalus residue

NASA Astrophysics Data System (ADS)

Feng, Ningchuan; Zhang, Yumei; Fan, Wei; Zhu, Meilin

2018-02-01

Activated carbon was prepared from astragalus residue by KOH and then treated with cetyl trimethyl ammonium bromide (CTAB) and used for the removal of methylbenzene from aqueous solution. The samples were characterized by FTIR, XRD, SEM and Boehm titration. The results showed that CTAB changed the physicochemical properties of activated carbon significantly. The isotherm adsorption studies of methylbenzene onto the astragalus residue activated carbon (ASC) and CTAB-modified astragalus residue activated carbon (ASCCTAB) were examined by using batch techniques and agreed well with the Langmuir model. The maximum adsorption capacity of ASC and ASC-CTAB for methylbenzene determined from the Langmuir model was183.56 mg/g and 235.18 mg/g, respectively. The results indicated that using CTAB as a modifier for ASC modification could markedly enhance the methylbenzene removal from water.

Polar drug residues in sewage and natural waters in the state of Rio de Janeiro, Brazil.

PubMed

Stumpf, M; Ternes, T A; Wilken, R D; Rodrigues, S V; Baumann, W

1999-01-12

The drug residues of lipid regulators, anti-inflammatories and some drug metabolites have been detected in raw sewage, treated waste water and river water in the state of Rio de Janeiro, Brazil. These residues are mainly derived from humans via excretion. The median concentrations in the effluents of sewage treatment plants (STPs) of most drugs investigated in this study ranged from 0.1 to 1 microgram/l. The removal rates of individual drugs during passage through a Brazilian STP varied from 12 to 90%. As a consequence of the incomplete removal of these residues during passage through a STP, rivers were also found to be contaminated. Median concentrations ranged from between 0.02 and 0.04 microgram/l in river water, whereas the maximum values were observed to be up to 0.5 microgram/l.

Doxycycline and sulfadimethoxine transfer from cross-contaminated feed to chicken tissues.

PubMed

Segato, G; Benetti, C; Angeletti, R; Montesissa, C; Biancotto, G

2011-01-01

During feed preparation at feed mills or during feed mixing in bins at farms, the accidental contamination of feed at trace levels by veterinary drug residues, commonly known as carry-over, can accidentally but frequently occur. To evaluate the concentrations of residual antimicrobials in poultry edible tissues, due to contaminated feed, sulfadimethoxine and doxycycline were administered for 10 days to chickens in poultry feed incurred at the contamination levels frequently found during national feed monitoring programmes (1-5 mg kg(-1)). Sulfadimethoxine and doxycycline residual concentrations detected in muscle (

Multiscale Analysis of the Residual Stresses Occurring During Curing and Cooling of Thick-Wall Cross-Ply Filament-Wound Cylinders

NASA Astrophysics Data System (ADS)

Memarianfard, H.; Turusov, R. A.

2017-11-01

A nonlinear numerical multiscale analysis to predict the residual shrinkage and thermal stresses arising during curing and cooling of thickwall cross-ply filament-wound cylinders of a reinforced polymer is performed at macro- and microscales using the representative volume element (RVE) of the composite. The mechanical behavior of the polymeric matrix is described by a nonlinear viscoelastic model with account of chemical shrinkage. The fiber material is considered elastic, isotropic, and temperature-independent. The maximum residual macrostresses arising during manufacture of the cylinders were calculated. The fields of residual microstresses in the RVE in three different zones across the thickness of the cylinders were found. Results of the microscale analysis showed that microstresses in some zones of RVE were several times higher than macrostresses in these areas.

An update discussion on the current assessment of the safety of veterinary antimicrobial drug residues in food with regard to their impact on the human intestinal microbiome.

PubMed

Cerniglia, Carl E; Pineiro, Silvia A; Kotarski, Susan F

2016-05-01

The human gastrointestinal tract ecosystem consists of complex and diverse microbial communities that have now been collectively termed the intestinal microbiome. Recent scientific breakthroughs and research endeavours have increased our understanding of the important role the intestinal microbiome plays in human health and disease. The use of antimicrobial new animal drugs in food-producing animals may result in the presence of low levels of drug residues in edible foodstuffs. There is concern that antimicrobial new animal drugs in or on animal-derived food products at residue-level concentrations could disrupt the colonization barrier and/or modify the antimicrobial resistance profile of human intestinal bacteria. Therapeutic doses of antimicrobial drugs have been shown to promote shifts in the intestinal microbiome, and these disruptions promote the emergence of antimicrobial-resistant bacteria. To assess the effects of antimicrobial new animal drug residues in food on human intestinal bacteria, many national regulatory agencies and international committees follow a harmonized process, VICH GL36(R), which was issued by a trilateral organization of the European Union, the USA, and Japan called the International Cooperation on Harmonization of Technical Requirements for Veterinary Medicinal Products (VICH). The guidance describes a general approach currently used by national regulatory agencies and international committees to assess the effects of antimicrobial new animal drug residues in animal-derived food on human intestinal bacteria. The purpose of this review is to provide an overview of this current approach as part of the antimicrobial new animal drug approval process in participating countries, give insights on the microbiological endpoints used in this safety evaluation, and discuss the availability of new information. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

An investigation of accelerating mode and decelerating mode constant-momentum mass spectrometry and their application to a residual gas analyzer

NASA Technical Reports Server (NTRS)

Ng, Y. S.

1977-01-01

A theoretical analysis of constant momentum mass spectrometry was made. A maximum resolving power for the decelerating mode constant momentum mass spectrometer was shown theoretically to exist for a beam of ions of known energy. A vacuum system and an electron beam ionization source was constructed. Supporting electronics for a residual gas analyzer were built. Experimental investigations of various types of accelerating and decelerating impulsive modes of a constant momentum mass spectrometer as applied to a residual gas analyzer were made. The data indicate that the resolving power for the decelerating mode is comparable to that of the accelerating mode.

On locating steganographic payload using residuals

NASA Astrophysics Data System (ADS)

Quach, Tu-Thach

2011-02-01

Locating steganographic payload usingWeighted Stego-image (WS) residuals has been proven successful provided a large number of stego images are available. In this paper, we revisit this topic with two goals. First, we argue that it is a promising approach to locate payload by showing that in the ideal scenario where the cover images are available, the expected number of stego images needed to perfectly locate all load-carrying pixels is the logarithm of the payload size. Second, we generalize cover estimation to a maximum likelihood decoding problem and demonstrate that a second-order statistical cover model can be used to compute residuals to locate payload embedded by both LSB replacement and LSB matching steganography.

Analysis techniques for residual acceleration data

NASA Technical Reports Server (NTRS)

Rogers, Melissa J. B.; Alexander, J. Iwan D.; Snyder, Robert S.

1990-01-01

Various aspects of residual acceleration data are of interest to low-gravity experimenters. Maximum and mean values and various other statistics can be obtained from data as collected in the time domain. Additional information may be obtained through manipulation of the data. Fourier analysis is discussed as a means of obtaining information about dominant frequency components of a given data window. Transformation of data into different coordinate axes is useful in the analysis of experiments with different orientations and can be achieved by the use of a transformation matrix. Application of such analysis techniques to residual acceleration data provides additional information than what is provided in a time history and increases the effectiveness of post-flight analysis of low-gravity experiments.

Ionic liquid based dispersive liquid-liquid microextraction for the extraction of pesticides from bananas.

PubMed

Ravelo-Pérez, Lidia M; Hernández-Borges, Javier; Asensio-Ramos, María; Rodríguez-Delgado, Miguel Angel

2009-10-23

This paper describes a dispersive liquid-liquid microextraction (DLLME) procedure using room temperature ionic liquids (RTILs) coupled to high-performance liquid chromatography with diode array detection capable of quantifying trace amounts of eight pesticides (i.e. thiophanate-methyl, carbofuran, carbaryl, tebuconazole, iprodione, oxyfluorfen, hexythiazox and fenazaquin) in bananas. Fruit samples were first homogenized and extracted (1g) with acetonitrile and after suitable evaporation and reconstitution of the extract in 10 mL of water, a DLLME procedure using 1-hexyl-3-methylimidazolium hexafluorophosphate ([C(6)MIM][PF(6)]) as extraction solvent was used. Experimental conditions affecting the DLLME procedure (sample pH, sodium chloride percentage, ionic liquid amount and volume of disperser solvent) were optimized by means of an experimental design. In order to determine the presence of a matrix effect, calibration curves for standards and fortified banana extracts (matrix matched calibration) were studied. Mean recovery values of the extraction of the pesticides from banana samples were in the range of 69-97% (except for thiophanate-methyl and carbofuran, which were 53-63%) with a relative standard deviation lower than 8.7% in all cases. Limits of detection achieved (0.320-4.66 microg/kg) were below the harmonized maximum residue limits established by the European Union (EU). The proposed method, was also applied to the analysis of this group of pesticides in nine banana samples taken from the local markets of the Canary Islands (Spain). To the best of our knowledge, this is the first application of RTILs as extraction solvents for DLLME of pesticides from samples different than water.

Pesticide extraction from table grapes and plums using ionic liquid based dispersive liquid-liquid microextraction.

PubMed

Ravelo-Pérez, Lidia M; Hernández-Borges, Javier; Herrera-Herrera, Antonio V; Rodríguez-Delgado, Miguel Angel

2009-12-01

Room temperature ionic liquids (RTILs) have been used as extraction solvents in dispersive liquid-liquid microextraction (DLLME) for the determination of eight multi-class pesticides (i.e. thiophanate-methyl, carbofuran, carbaryl, tebuconazole, iprodione, oxyfluorfen, hexythiazox, and fenazaquin) in table grapes and plums. The developed method involves the combination of DLLME and high-performance liquid chromatography with diode array detection. Samples were first homogenized and extracted with acetonitrile. After evaporation and reconstitution of the extract in water containing sodium chloride, a quick DLLME procedure that used the ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate ([C(6)MIM][PF(6)]) and methanol was developed. The RTIL dissolved in a very small volume of acetonitrile was directed injected in the chromatographic system. The comparison between the calibration curves obtained from standards and from spiked sample extracts (matrix-matched calibration) showed the existence of a strong matrix effect for most of the analyzed pesticides. A recovery study was also developed with five consecutive extractions of the two types of fruits spiked at three concentration levels. Mean recovery values were in the range of 72-100% for table grapes and 66-105% for plum samples (except for thiophanate-methyl and carbofuran, which were 64-75% and 58-66%, respectively). Limits of detection (LODs) were in the range 0.651-5.44 microg/kg for table grapes and 0.902-6.33 microg/kg for plums, representing LODs below the maximum residue limits (MRLs) established by the European Union in these fruits. The potential of the method was demonstrated by analyzing 12 commercial fruit samples (six of each type).

Heavy metal concentrations in bovine tissues (muscle, liver and kidney) and their relationship with heavy metal contents in consumed feed.

PubMed

Hashemi, Majid

2018-06-15

Toxic (lead, cadmium and mercury) and essential trace (copper and zinc) metals were measured in muscle, liver and kidney samples of bovine and their relationships with heavy metal concentrations in consumed feed were studied. A total of 216 tissue samples from 72 cows and 216 feed samples from 18 farms were collected during four seasons and analyzed for heavy metals by inductively coupled plasma-optical emission spectrometry after wet digestion. The arithmetic mean concentrations (mg/Kg wet weight) of lead (Pb), cadmium (Cd) and mercury were respectively, 0.221, 0.028 and 0.003 in muscle, 0.273, 0.047 and 0.002 in liver and 0.244, 0.114 and 0.003 in kidney. All measured concentrations (with the exception of Pb in muscle) were below the European Union maximum residual limits (MRL). The Cd contents of the kidney were significantly higher than which observed in other tissues. Although, copper (Cu) and zinc (Zn) levels in all of samples were below MRL, but results showed that many cattles may be suffering from Cu and/or Zn deficiency. Significant and positive correlations between Pb (p < 0.05, r = 0.163) and Cd (p < 0.01, r = 0.303) concentrations in feed and studied organs were observed. As a considerable amount of metals above MRL were noticed in our study, continuous monitoring of these metals is recommended to avoid hazardous transfer to human through the food of animal origin. Copyright © 2018 Elsevier Inc. All rights reserved.

Identification and quantification of five macrolide antibiotics in several tissues, eggs and milk by liquid chromatography-electrospray tandem mass spectrometry.

PubMed

Dubois, M; Fluchard, D; Sior, E; Delahaut, P

2001-04-05

We present an electrospray high-performance liquid chromatographic tandem mass spectrometric (HPLC-MS-MS) method capable of determining in several tissues (muscle, kidney, liver), eggs and milk the following five macrolides: tylosin, tilmicosin, spiramycin, josamycin, erythromycin. Roxithromycin was used as an internal standard. The method uses extraction in a Tris buffer at pH 10.5, followed by protein precipitation with sodium tungstate and clean-up on an Oasis solid-phase extraction column. The HPLC separation was performed on a Purospher C18 column (125 x 3 mm I.D.) protected by a guard column, with a gradient of aqueous 0.1 M ammonium acetate-acetonitrile as the mobile phase at a flow-rate of 0.7 ml min(-1). Protonated molecules served as precursor ions for electrospray ionisation in the positive ion mode and four product ions were chosen for each analyte for multiple reaction monitoring (MRM). A validation study was conducted to confirm the five macrolides by MRM HPLC-MS-MS analysis of a negative control and fortified samples. All of the samples analysed were confirmed with four ions. The ion ratio reproducibility limit ranged from 2.4 to 15%. All compounds could be detected and quantified at half-maximum residue limits (MRLs). The method is specific, quantitative and reproducible enough to conform to European Union recommendations within the concentration range 0.5 MRL-2 MRL (accuracy: 80 to 110%, relative standard deviation: 2 to 13%). This whole method allows extraction and analysis of up to 50 samples per day.

Application of the maximum entropy principle to determine ensembles of intrinsically disordered proteins from residual dipolar couplings.

PubMed

Sanchez-Martinez, M; Crehuet, R

2014-12-21

We present a method based on the maximum entropy principle that can re-weight an ensemble of protein structures based on data from residual dipolar couplings (RDCs). The RDCs of intrinsically disordered proteins (IDPs) provide information on the secondary structure elements present in an ensemble; however even two sets of RDCs are not enough to fully determine the distribution of conformations, and the force field used to generate the structures has a pervasive influence on the refined ensemble. Two physics-based coarse-grained force fields, Profasi and Campari, are able to predict the secondary structure elements present in an IDP, but even after including the RDC data, the re-weighted ensembles differ between both force fields. Thus the spread of IDP ensembles highlights the need for better force fields. We distribute our algorithm in an open-source Python code.

Optimization of a Nucleic Acids united-RESidue 2-Point model (NARES-2P) with a maximum-likelihood approach

NASA Astrophysics Data System (ADS)

He, Yi; Liwo, Adam; Scheraga, Harold A.

2015-12-01

Coarse-grained models are useful tools to investigate the structural and thermodynamic properties of biomolecules. They are obtained by merging several atoms into one interaction site. Such simplified models try to capture as much as possible information of the original biomolecular system in all-atom representation but the resulting parameters of these coarse-grained force fields still need further optimization. In this paper, a force field optimization method, which is based on maximum-likelihood fitting of the simulated to the experimental conformational ensembles and least-squares fitting of the simulated to the experimental heat-capacity curves, is applied to optimize the Nucleic Acid united-RESidue 2-point (NARES-2P) model for coarse-grained simulations of nucleic acids recently developed in our laboratory. The optimized NARES-2P force field reproduces the structural and thermodynamic data of small DNA molecules much better than the original force field.

Successful resection of a giant mediastinal non-seminomatous germ cell tumor showing fluorodeoxyglucose accumulation after neoadjuvant chemotherapy: report of a case.

PubMed

Takada, Kazuki; Morodomi, Yosuke; Okamoto, Tatsuro; Suzuki, Yuzo; Fujishita, Takatoshi; Kitahara, Hirokazu; Shimamatsu, Shinichiro; Kohno, Mikihiro; Kawano, Daigo; Hidaka, Noriko; Nakanishi, Yoichi; Maehara, Yoshihiko

2014-05-01

A 32-year-old man presented with a mediastinal non-seminomatous germ cell tumor showing fluorodeoxyglucose (FDG) accumulation (maximum standardized uptake value = 22.21) and extremely elevated blood alpha-fetoprotein (AFP) level (9203.0 ng/ml). The patient underwent 4 cycles of neoadjuvant chemotherapy (cisplatin, bleomycin, and etoposide), which normalized the AFP level and reduced the tumor size, allowing complete resection without a support of extracorporeal circulation. Despite preoperative positron emission tomography revealing increased FDG uptake in the residual tumor (maximum standardized uptake value = 3.59), the pathologic evaluation revealed that no viable germ cell tumor cells remained. We believe FDG uptake should not be used as a criterion for surgical resection after neoadjuvant chemotherapy. It is appropriate to resect the residual tumor regardless of FDG uptake after induction chemotherapy if a tumor is resectable and the AFP level normalizes.

Evaluation of pesticide residue dynamics in Chinese cabbage, head cabbage and cauliflower.

PubMed

Kocourek, František; Stará, Jitka; Holý, Kamil; Horská, Tereza; Kocourek, Vladimír; Kováčová, Jana; Kohoutková, Jana; Suchanová, Marie; Hajšlová, Jana

2017-06-01

Pesticide residues from the time of application until harvest were analysed for 20, 17 and 18 active insecticidal and fungicidal substances in Chinese cabbage, head cabbage and cauliflower, respectively. In total, 40 mathematical models of residue degradation were developed using a first-order kinetic equation, and from these models it was possible to forecast the action pre-harvest interval for a given action threshold for low-residue production in Brassica vegetables as a percentage of the maximum residue level. Additionally, it was possible to establish an action pre-harvest interval based on an action threshold of 0.01 mg kg ‒1 for the production of Brassica vegetables for baby food. Among the evaluated commodities, the speed of residue degradation was highest in head cabbage, medium in Chinese cabbage and lowest in cauliflower. The half-lives of pesticide in various vegetables were also determined: they ranged from 1.55 to 5.25 days in Chinese cabbage, from 0.47 to 6.54 days in head cabbage and from 1.88 to 7.22 days in cauliflower.

Validation of an UHPLC-MS/MS Method for Screening of Antimicrobial Residues in Eggs and Their Application to Analyses of Eggs from Laying Hens Subjected to Pharmacological Treatment

PubMed Central

Caldeira, Letícia Gomes Magnago; Santos, Flávio Alves; de Oliveira, Andréa Melo Garcia; Lima, Josefa Abucater; de Souza, Leonardo Francisco; da Silva, Guilherme Resende; de Assis, Débora Cristina Sampaio

2017-01-01

A multiresidue method by UHPLC/MS-MS was optimized and validated for the screening and semiquantitative detection of antimicrobials residues from tetracyclines, aminoglycosides, quinolones, lincosamides, β-lactams, sulfonamides, and macrolides families in eggs. A qualitative approach was used to ensure adequate sensitivity to detect residues at the level of interest, defined as maximum residue limit (MRL), or less. The applicability of the methods was assessed by analyzing egg samples from hens that had been subjected to pharmacological treatment with neomycin, enrofloxacin, lincomycin, oxytetracycline, and doxycycline during five days and after discontinuation of medication (10 days). The method was adequate for screening all studied analytes in eggs, since the performance parameters ensured a false-compliant rate below or equal to 5%, except for flumequine. In the analyses of eggs from laying hens subjected to pharmacological treatment, all antimicrobial residues were detected throughout the experimental period, even after discontinuation of medication, except for neomycin, demonstrating the applicability of the method for analyses of antimicrobial residues in eggs. PMID:29181222

Comparison of various pretreatments for ethanol production enhancement from solid residue after rumen fluid digestion of rice straw.

PubMed

Zhang, Haibo; Zhang, Panyue; Ye, Jie; Wu, Yan; Liu, Jianbo; Fang, Wei; Xu, Dong; Wang, Bei; Yan, Li; Zeng, Guangming

2018-01-01

The rumen digested residue of rice straw contains high residual carbohydrates, which makes it a potential cellulosic ethanol feedstock. This study evaluated the feasibility and effectiveness of applying microwave assisted alkali (MAP), ultrasound assisted alkali (UAP), and ball milling pretreatment (BMP) to enhance ethanol production from two digested residues (2.5%-DR and 10%-DR) after rumen fluid digestion of rice straw at 2.5% and 10.0% solid content. Results revealed that 2.5%-DR and 10%-DR had a cellulose content of 36.4% and 41.7%, respectively. MAP and UAP improved enzymatic hydrolysis of digested residue by removing the lignin and hemicellulose, while BMP by decreasing the particle size and crystallinity. BMP was concluded as the suitable pretreatment, resulting in an ethanol yield of 116.65 and 147.42mgg -1 for 2.5%-DR and 10%-DR, respectively. The integrated system including BMP for digested residue at 2.5% solid content achieved a maximum energy output of 7010kJkg -1 . Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact Damage and Strain Rate Effects for Toughened Epoxy Composite Structures

NASA Technical Reports Server (NTRS)

Chamis, Christos C.; Minnetyan, Levon

2006-01-01

Structural integrity of composite systems under dynamic impact loading is investigated herein. The GENOA virtual testing software environment is used to implement the effects of dynamic loading on fracture progression and damage tolerance. Combinations of graphite and glass fibers with a toughened epoxy matrix are investigated. The effect of a ceramic coating for the absorption of impact energy is also included. Impact and post impact simulations include verification and prediction of (1) Load and Impact Energy, (2) Impact Damage Size, (3) Maximum Impact Peak Load, (4) Residual Strength, (5) Maximum Displacement, (6) Contribution of Failure Modes to Failure Mechanisms, (7) Prediction of Impact Load Versus Time, and (8) Damage, and Fracture Pattern. A computer model is utilized for the assessment of structural response, progressive fracture, and defect/damage tolerance characteristics. Results show the damage progression sequence and the changes in the structural response characteristics due to dynamic impact. The fundamental premise of computational simulation is that the complete evaluation of composite fracture requires an assessment of ply and subply level damage/fracture processes as the structure is subjected to loads. Simulation results for the graphite/epoxy composite were compared with the impact and tension failure test data, correlation and verification was obtained that included: (1) impact energy, (2) damage size, (3) maximum impact peak load, (4) residual strength, (5) maximum displacement, and (6) failure mechanisms of the composite structure.

Pesticide residue evaluation in major staple food items of Ethiopia using the QuEChERS method: a case study from the Jimma Zone.

PubMed

Mekonen, Seblework; Ambelu, Argaw; Spanoghe, Pieter

2014-06-01

Samples of maize, teff, red pepper, and coffee (green bean and coffee bean with pulp) were collected from a local market in the Jimma Zone, Ethiopia. Samples were analyzed for the occurrence of cypermethrin, permethrin, deltamethrin, chlorpyrifos ethyl, DTT and its metabolites, and endosulfan (α, β). In the analytical procedure, the QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) extraction methodology with dispersive solid phase extraction clean up (d-SPE) technique was applied. Validation of the QuEChERS method was satisfactory. Recovery percentages of most pesticides were in the range of 70% to 120%, with good repeatability (%relative standard deviation < 20). The limit of detection and limit of quantification varied between 0.001 µg/g and 0.092 µg/g and between 0.002 µg/g and 0.307 µg/g, respectively. The main pesticides detected were DDT, endosulfan, cypermethrin, and permethrin. All of the pesticides analyzed were detected in red pepper and green coffee bean. Residues of DDT in coffee pulp significantly differed (p < 0.01) from other food items except for red pepper. The concentration of pesticides in the food items varied from 0.011 mg/kg to 1.115 mg/kg. All food items contained 1 or more pesticides. Two-thirds of the samples had residues below corresponding maximum residue limits, and the remaining one-third of samples were above the maximum residue limits. These results indicate the need for a good pesticide monitoring program to evaluate consumer risk for the Ethiopian people. © 2014 SETAC.

Supernovae anisotropy power spectrum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghodsi, Hoda; Baghram, Shant; Habibi, Farhang, E-mail: h.ghodsi@mehr.sharif.ir, E-mail: baghram@sharif.edu, E-mail: habibi@lal.in2p3.fr

2017-10-01

We contribute another anisotropy study to this field of research using Type Ia supernovae (SNe Ia). In this work, we utilise the power spectrum calculation method and apply it to both the current SNe Ia data and simulation. Using the Union2.1 data set at all redshifts, we compare the spectrum of the residuals of the observed distance moduli to that expected from an isotropic universe affected by the Union2.1 observational uncertainties at low multipoles. Through this comparison we find a dipolar anisotropy with tension of less that 2σ towards l = 171° ± 21° and b = −26° ± 28°more » which is mainly induced by anisotropic spatial distribution of the SNe with z > 0.2 rather than being a cosmic effect. Furthermore, we find a tension of ∼ 4σ at ℓ = 4 between the two spectra. Our simulations are constructed with the characteristics of the upcoming surveys like the Large Synoptic Survey Telescope (LSST), which shall bring us the largest SNe Ia collection to date. We make predictions for the amplitude of a possible dipolar anisotropy that would be detectable by future SNe Ia surveys.« less

Matrix-Matching as an Improvement Strategy for the Detection of Pesticide Residues.

PubMed

Giacinti, Géraldine; Raynaud, Christine; Capblancq, Sophie; Simon, Valérie

2016-05-01

More than 90% of the pesticides residues in apples are located in the peel. We developed a gas chromatography/ion trap tandem mass spectrometry method for investigating all detectable residues in the peel of 3 apple varieties. Sample preparation is based on the use of the Quick Easy Cheap Effective Rugged and Safe method on the whole fruit, the flesh, and the peel. Pesticide residues were quantified with solvent-matched and matrix-matched standards, by spiking apple sample extracts. Matrix effects dependent on the type of extract (fruit, flesh, or peel) and the apple variety were detected. The best data processing methods involved normalizing matrix effect rates by matrix-matched internal/external calibration. Boscalid, captan, chlorpyrifos, fludioxonil, and pyraclostrobin were the most frequently detected pesticides. However, their concentrations in the whole fruit were below European maximum residue levels. Despite negative matrix effects, the residues in peel were detected at concentrations up to 10 times higher than those in whole fruits. Consequently, other pesticide residues present at concentrations below the limit of quantification in the whole fruit were detected in the peel. © 2016 Institute of Food Technologists®

Evaluation of the Presence and Levels of Enrofloxacin, Ciprofloxacin, Sulfaquinoxaline and Oxytetracycline in Broiler Chickens after Drug Administration

PubMed Central

da Silva, Guilherme Resende; Lanza, Isabela Pereira; Ribeiro, Ana Cláudia dos Santos Rossi; Lana, Ângela Maria Quintão; Lara, Leonardo José Camargos

2016-01-01

The depletion times of enrofloxacin and its metabolite ciprofloxacin as well as sulfaquinoxaline and oxytetracycline were evaluated in broiler chickens that had been subjected to pharmacological treatment. The presence and residue levels of these drugs in muscle tissue were evaluated using an ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method that was validated in this work. The results showed the presence of all antimicrobial residues; however, the presence of residues at concentrations higher than the drugs’ maximum residue limit (MRL) of 100 μg kg-1 was found only during the treatment period for oxytetracycline and until two days after discontinuation of the medication for enrofloxacin, ciprofloxacin and sulfaquinoxaline. It was concluded that the residues of all antimicrobials were rapidly metabolized from the broiler muscles; after four days of withdrawal, the levels were lower than the limit of quantification (LOQ) of the method for the studied analytes. PMID:27846314

Evaluation of the Presence and Levels of Enrofloxacin, Ciprofloxacin, Sulfaquinoxaline and Oxytetracycline in Broiler Chickens after Drug Administration.

PubMed

de Assis, Débora Cristina Sampaio; da Silva, Guilherme Resende; Lanza, Isabela Pereira; Ribeiro, Ana Cláudia Dos Santos Rossi; Lana, Ângela Maria Quintão; Lara, Leonardo José Camargos; de Figueiredo, Tadeu Chaves; Cançado, Silvana de Vasconcelos

2016-01-01

The depletion times of enrofloxacin and its metabolite ciprofloxacin as well as sulfaquinoxaline and oxytetracycline were evaluated in broiler chickens that had been subjected to pharmacological treatment. The presence and residue levels of these drugs in muscle tissue were evaluated using an ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method that was validated in this work. The results showed the presence of all antimicrobial residues; however, the presence of residues at concentrations higher than the drugs' maximum residue limit (MRL) of 100 μg kg-1 was found only during the treatment period for oxytetracycline and until two days after discontinuation of the medication for enrofloxacin, ciprofloxacin and sulfaquinoxaline. It was concluded that the residues of all antimicrobials were rapidly metabolized from the broiler muscles; after four days of withdrawal, the levels were lower than the limit of quantification (LOQ) of the method for the studied analytes.

Viscoelasticity of human oral mucosa: implications for masticatory biomechanics.

PubMed

Sawada, A; Wakabayashi, N; Ona, M; Suzuki, T

2011-05-01

The dynamic behavior of oral soft tissues supporting removable prostheses is not well understood. We hypothesized that the stress and strain of the mucosa exhibited time-dependent behavior under masticatory loadings. Displacement of the mucosa on the maxillary residual ridge was measured in vivo by means of a magnetic actuator/sensor under vertical loading in partially edentulous individuals. Subject-specific finite element models of homogeneous bone and mucosa were constructed based on computed tomography images. A mean initial elastic modulus of 8.0 × 10(-5) GPa and relaxation time of 494 sec were obtained from the curve adaptation of the finite element output to the in vivo time-displacement relationship. Delayed increase of the maximum compressive strain on the surface of the mucosa was observed under sustained load, while the maximum strain inside the mucosa was relatively low and uninfluenced by the duration of the load. The compressive stress showed a slight decrease with sustained load, due to stress relaxation of the mucosa. On simulation of cyclic load, the increment of the maximum strain and the evidence of residual strain were revealed after each loading. The results support our hypothesis, and suggest that sustained and repetitive loads accumulate as surface strain on the mucosa.

Alkalistable endo-β-1,4-xylanase production from a newly isolated alkalitolerant Penicillium sp. SS1 using agro-residues.

PubMed

Bajaj, Bijender Kumar; Sharma, Mukul; Sharma, Sunny

2011-09-01

Thermostable and alkalitolerant xylanases have got intense research focus due to their vast applications in various industries including pulp and paper, food, feed, textile, biofuel, etc. In the present investigation, a Penicillum sp. SS1 isolated from degrading woody material was found to produce moderately thermoactive and alkalistable endo-β-1,4-xylanase (xylanase). Maximum xylanase production was observed after fourth day of fermentation (43.84 IU/ml). The organism produced substantial quantities of xylanase using agricultural residues like wheat bran (20.6 IU/ml), rice bran (21.8 IU/ml) and sawdust (10.7 IU/ml) as carbon sources. The enzyme preparation was totally free of filter paper activity (FPase) and possessed negligible carboxymethyl cellulase (CMCase) activity; this could be an important feature of enzyme if the intended application of enzyme is in pulp and paper industries. Among nitrogen sources examined, yeast extract supported maximum xylanase production (45.74 IU/ml), and was followed by soybean meal (22.2 IU/ml) and ammonium sulphate (20 IU/ml). Maximum xylanase production was observed at initial medium pH 9 (25.6 IU/ml); however, at pH 8 and 10 also significantly high enzyme titre was observed (24 and 21.2 IU/ml, respectively). Thus, Penicillium sp. SS1 displayed capability of growing and producing xylanase at high alkaline pH (8-10). Maximum xylanase activity was reported at 50 °C, however, significantly high activity was observed at 60 °C (65.4%), however, at 70-80 °C activity was lost considerably. At 50-60 °C the enzyme retained very high activity up to 30-60 min (91-100%), however, prolonged incubation (90 min) caused considerable activity reduction (residual activity 63-68%).

Pesticide Tolerances

EPA Pesticide Factsheets

EPA regulates pesticides used to protect crops and sets limits on the amount of pesticide remaining in or on foods in the U.S. The limits on pesticides on foods are called tolerances in the U.S. (maximum residue limits (MRLs) in many other countries).

Cross-Sectional And Longitudinal Uncertainty Propagation In Drinking Water Risk Assessment

NASA Astrophysics Data System (ADS)

Tesfamichael, A. A.; Jagath, K. J.

2004-12-01

Pesticide residues in drinking water can vary significantly from day to day. However, drinking water quality monitoring performed under the Safe Drinking Water Act (SDWA) at most community water systems (CWSs) is typically limited to four data points per year over a few years. Due to limited sampling, likely maximum residues may be underestimated in risk assessment. In this work, a statistical methodology is proposed to study the cross-sectional and longitudinal uncertainties in observed samples and their propagated effect in risk estimates. The methodology will be demonstrated using data from 16 CWSs across the US that have three independent databases of atrazine residue to estimate the uncertainty of risk in infants and children. The results showed that in 85% of the CWSs, chronic risks predicted with the proposed approach may be two- to four-folds higher than that predicted with the current approach, while intermediate risks may be two- to three-folds higher in 50% of the CWSs. In 12% of the CWSs, however, the proposed methodology showed a lower intermediate risk. A closed-form solution of propagated uncertainty will be developed to calculate the number of years (seasons) of water quality data and sampling frequency needed to reduce the uncertainty in risk estimates. In general, this methodology provided good insight into the importance of addressing uncertainty of observed water quality data and the need to predict likely maximum residues in risk assessment by considering propagation of uncertainties.

Pesticide residue in water--a challenging task in India.

PubMed

Agarwal, Akriti; Prajapati, Rajmani; Singh, Om Pal; Raza, S K; Thakur, L K

2015-02-01

Modern agriculture practices reveal an increase in use of pesticides to meet the food demand of increasing population which results in contamination of the environment. In India, crop production increased to 100 %, but the cropping area has increased marginally by 20 %. Pesticides have played a major role in achieving the maximum crop production but maximum usage and accumulation of pesticide residues is highly detrimental to aquatic and other ecosystem. Pesticide residues in drinking water have become a major challenge over the last few years. It has been monitored in public water supply resources in National capital territory, i.e., Delhi. Organochlorine pesticides (OCPs), mainly isomers of hexachlorohexane (HCH), dichloro-diphenyl-trichloroethane (DDT), endosulphan, endrin, aldrin, dieldrin, and heptachlore, were identified from potable water samples. Results suggested that continuous consumption of contaminated water can pose severe health threats to local residents of this area. Central Pollution Control Board (CPCB), Delhi, had found α and β isomers of endosulphan residues in the Yamuna river. High concentrations of γ-HCH (0.259 μg/l) and malathion (2.618 μg/l) were detected in the surface water samples collected from the river Ganga in Kanpur, Uttar Pradesh (UP). High concentration of methyl parathion, endosulfan, and DDT were observed in water samples collected from the river at Bhagalpur, Bihar. The Industrial Toxicology Research Centre (ITRC), Lucknow (UP) study also found 0.5671 ppb concentrations of endosulfan in the river at Allahabad, UP. Similar results were found in other water samples in India.

Low-Residue and Low-Fiber Diets in Gastrointestinal Disease Management12

PubMed Central

Vanhauwaert, Erika; Matthys, Christophe; Verdonck, Lies; De Preter, Vicky

2015-01-01

Recently, low-residue diets were removed from the American Academy of Nutrition and Dietetics’ Nutrition Care Manual due to the lack of a scientifically accepted quantitative definition and the unavailability of a method to estimate the amount of food residue produced. This narrative review focuses on defining the similarities and/or discrepancies between low-residue and low-fiber diets and on the diagnostic and therapeutic values of these diets in gastrointestinal disease management. Diagnostically, a low-fiber/low-residue diet is used in bowel preparation. A bowel preparation is a cleansing of the intestines of fecal matter and secretions conducted before a diagnostic procedure. Therapeutically, a low-fiber/low-residue diet is part of the treatment of acute relapses in different bowel diseases. The available evidence on low-residue and low-fiber diets is summarized. The main findings showed that within human disease research, the terms “low residue” and “low fiber” are used interchangeably, and information related to the quantity of residue in the diet usually refers to the amount of fiber. Low-fiber/low-residue diets are further explored in both diagnostic and therapeutic situations. On the basis of this literature review, the authors suggest redefining a low-residue diet as a low-fiber diet and to quantitatively define a low-fiber diet as a diet with a maximum of 10 g fiber/d. A low-fiber diet instead of a low-residue diet is recommended as a diagnostic value or as specific therapy for gastrointestinal conditions. PMID:26567203

Pesticide residue determination in vegetables from western China applying gas chromatography with mass spectrometry.

PubMed

Qin, Guofu; Zou, Keting; Li, Yongbo; Chen, Yan; He, Fengrui; Ding, Guirong

2016-09-01

In this study,an effort has been made to evaluate the pesticide residues in vegetables from western China. Fifty-one pesticides, including organophosphorus, organochlorine, carbamate and pyrethroid, were detected in 369 commonly used vegetables by GC-MS. Concentrations of organophosphorus pesticides were detected ranging from 0.0008 to 18.8200 mg/kg, among which organophosphorus pesticide concentrations exceeded their maximum residue levels (MRLs) in five samples. Carbamate and organochlorine pesticides were determined to have concentrations in the range of 0.0012-0.7928 mg/kg. The residual concentrations of carbamate pesticides in six samples and organochlorine pesticides in four samples exceeded their MRLs. The residual concentrations of five pyrethroid pesticides were within the range of 0.0016-6.0827 mg/kg and the pyrethroid residues in two samples exceeded their MRLs. The results revealed that pesticide residues in 70.73% of the vegetables samples were not detected, while in the rest of vegetables there were one or more pesticide residues and some even exceeded their MRLs, which would threaten the health of consumers. Our work provides significant information for the food safety regulations to control the excessive use of some pesticides on those kinds of vegetables from western China. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Testing the shape of distributions of weather data

NASA Astrophysics Data System (ADS)

Baccon, Ana L. P.; Lunardi, José T.

2016-08-01

The characterization of the statistical distributions of observed weather data is of crucial importance both for the construction and for the validation of weather models, such as weather generators (WG's). An important class of WG's (e.g., the Richardson-type generators) reduce the time series of each variable to a time series of its residual elements, and the residuals are often assumed to be normally distributed. In this work we propose an approach to investigate if the shape assumed for the distribution of residuals is consistent or not with the observed data of a given site. Specifically, this procedure tests if the same distribution shape for the residuals noise is maintained along the time. The proposed approach is an adaptation to climate time series of a procedure first introduced to test the shapes of distributions of growth rates of business firms aggregated in large panels of short time series. We illustrate the procedure by applying it to the residuals time series of maximum temperature in a given location, and investigate the empirical consistency of two assumptions, namely i) the most common assumption that the distribution of the residuals is Gaussian and ii) that the residuals noise has a time invariant shape which coincides with the empirical distribution of all the residuals noise of the whole time series pooled together.

Chapter 5: Geologic Assessment of Undiscovered Petroleum Resources in the Waltman Shale Total Petroleum System,Wind River Basin Province, Wyoming

USGS Publications Warehouse

Roberts, Steve B.; Roberts, Laura N.R.; Cook, Troy

2007-01-01

The Waltman Shale Total Petroleum System encompasses about 3,400 square miles in the Wind River Basin Province, Wyoming, and includes accumulations of oil and associated gas that were generated and expelled from oil-prone, lacustrine shale source rocks in the Waltman Shale Member of the Paleocene Fort Union Formation. Much of the petroleum migrated and accumulated in marginal lacustrine (deltaic) and fluvial sandstone reservoirs in the Shotgun Member of the Fort Union, which overlies and intertongues with the Waltman Shale Member. Additional petroleum accumulations derived from Waltman source rocks are present in fluvial deposits in the Eocene Wind River Formation overlying the Shotgun Member, and also might be present within fan-delta deposits included in the Waltman Shale Member, and in fluvial sandstone reservoirs in the uppermost part of the lower member of the Fort Union Formation immediately underlying the Waltman. To date, cumulative production from 53 wells producing Waltman-sourced petroleum exceeds 2.8 million barrels of oil and 5.8 billion cubic feet of gas. Productive horizons range from about 1,770 feet to 5,800 feet in depth, and average about 3,400 to 3,500 feet in depth. Formations in the Waltman Shale Total Petroleum System (Fort Union and Wind River Formations) reflect synorogenic deposition closely related to Laramide structural development of the Wind River Basin. In much of the basin, the Fort Union Formation is divided into three members (ascending order): the lower unnamed member, the Waltman Shale Member, and the Shotgun Member. These members record the transition from deposition in dominantly fluvial, floodplain, and mire environments in the early Paleocene (lower member) to a depositional setting characterized by substantial lacustrine development (Waltman Shale Member) and contemporaneous fluvial, and marginal lacustrine (deltaic) deposition (Shotgun Member) during the middle and late Paleocene. Waltman Shale Member source rocks have total organic carbon values ranging from 0.93 to 6.21 weight percent, averaging about 2.71 weight percent. The hydrocarbon generative potential of the source rocks typically exceeds 2.5 milligrams of hydrocarbon per gram of rock and numerous samples had generative potentials exceeding 6.0 milligrams of hydrocarbon per gram of rock. Waltman source rocks are oil prone, and contain a mix of Type-II and Type-III kerogen, indicating organic input from a mix of algal and terrestrial plant matter, or a mix of algal and reworked or recycled material. Thermal maturity at the base of the Waltman Shale Member ranges from a vitrinite reflectance value of less than 0.60 percent along the south basin margin to projected values exceeding 1.10 percent in the deep basin west of Madden anticline. Burial history reconstructions for three wells in the northern part of the Wind River Basin indicate that the Waltman Shale Member was well within the oil window (Ro equal to or greater than 0.65 percent) by the time of maximum burial about 15 million years ago; maximum burial depths exceeded 10,000 feet. Onset of oil generation calculated for the base of the Waltman Shale member took place from about 49 million years ago to about 20 million years ago. Peak oil generation occurred from about 31 million years ago to 26 million years ago in the deep basin west of Madden anticline. Two assessment units were defined in the Waltman Shale Total Petroleum System: the Upper Fort Union Sandstones Conventional Oil and Gas Assessment Unit (50350301) and the Waltman Fractured Shale Continuous Oil Assessment Unit (50350361). The conventional assessment unit primarily relates to the potential for undiscovered petroleum accumulations that are derived from source rocks in the Waltman Shale Member and trapped within sandstone reservoirs in the Shotgun Member (Fort Union Formation) and in the lower part of the overlying Wind River Formation. The potential for Waltman-sourced oil accumulations in fan-delta depos

Agricultural residues for cellulolytic enzyme production by Aspergillus niger: effects of pretreatment.

PubMed

Salihu, Aliyu; Abbas, Olagunju; Sallau, Abdullahi Balarabe; Alam, Md Zahangir

2015-12-01

Different agricultural residues were considered in this study for their ability to support cellulolytic enzyme production by Aspergillus niger. A total of eleven agricultural residues including finger millet hulls, sorghum hulls, soybean hulls, groundnut husk, banana peels, corn stalk, cassava peels, sugarcane bagasse, saw dust, rice straw and sheanut cake were subjected to three pretreatment (acid, alkali and oxidative) methods. All the residues supported the growth and production of cellulases by A. niger after 96 h of incubation. Maximum cellulase production was found in alkali-treated soybean hulls with CMCase, FPase and β-glucosidase yields of 9.91 ± 0.04, 6.20 ± 0.13 and 5.69 ± 0.29 U/g, respectively. Further studies in assessing the potential of soybean hulls are being considered to optimize the medium composition and process parameters for enhanced cellulase production.

Dissipation and residue of azoxystrobin in banana under field condition.

PubMed

Wang, Siwei; Sun, Haibin; Liu, Yanping

2013-09-01

A method was developed for determining azoxystrobin in banana and cultivation soil using gas chromatography. The dissipation and residue of azoxystrobin in banana fields at GAP conditions were investigated. The average recoveries ranged from 80.3 to 96.0 % with relative standard deviations of 2.9 to 7.2 % at three different spiking levels for each matrix. The results indicated that the half-life of azoxystrobin in bananas and soil ranged from 7.5 to 13.5 days in Guangdong and from 8.7 to 12.7 days in Fujian. The dissipation rates of azoxystrobin in banana and soil were almost the same. Terminal residues in banana and banana flesh (0.01 mg/kg) were all below the maximum residue limit (2 mg/kg by Codex Alimentarius Commission and China). The results demonstrated that the safety of using azoxystrobin at the recommended agriculture dosage to protect bananas from diseases.

Vibration activity evaluation of double-span rotor at rundown caused by its initial curvature and residual unbalance

NASA Astrophysics Data System (ADS)

Kostyuk, A. G.; Volokhovskaya, O. A.

2017-01-01

The work is dedicated to the study of vibration activity of double-span rotor of turbine unit (TU) consisting of a high-pressure rotor and a rotor of medium-low pressure rotor combined with it (HPR—MLPR system) at the lowest critical rotational frequencies at rundown. When using the design model of the system, it was assumed that the rotors were installed on anisotropic elastic-damper supports, tied among themselves by a rigid clutch, and having the initial curvature (nonremovable initial deflection) and the residual unbalances in both spans. Two types of bearings were considered-elliptical and six-shoe segmental bearings. It was believed that the initial deflection during operation or as a result of noncompliance of start-up conditions initially gets only HPR and the axis shape of unloaded HPR is known and it is a flat curve. The resultant curve of nonremovable deflection of the HPR-MLPR system occurring after installing the shafting into the bearings was also considered flat and located in the same plane as the initial deflection of HPR. The cases of additional presence with the rotors of concentrated residual unbalances in the middle of each span are considered. The case of availability with both rotors of the shafting antisymmetric point unbalances on each of the spans was not considered in this work. The values of each of the factors of vibration activity (of the initial deflection of HPR and residual unbalances of both rotors) were chosen to be equal to the maximum permissible established by the active in the practice of TU operation limitations on the maximum values of the initial deflection of thermally unstable rotor and its residual unbalances. The influence of location of residual unbalances in relation to the initial deflection curve of HPR-MLPR system on the total amplitudes of transient vibrations caused by both excitation factors in the reference points of the system at TU rundown was investigated. It was established that, at the unfavorable relations between directions of curvature of the rotors of HPR-MLPR system and their residual unbalances with segmental bearings, touching in the diaphragm seals in the middle of HPR span is possible.

Low-residue and low-fiber diets in gastrointestinal disease management.

PubMed

Vanhauwaert, Erika; Matthys, Christophe; Verdonck, Lies; De Preter, Vicky

2015-11-01

Recently, low-residue diets were removed from the American Academy of Nutrition and Dietetics' Nutrition Care Manual due to the lack of a scientifically accepted quantitative definition and the unavailability of a method to estimate the amount of food residue produced. This narrative review focuses on defining the similarities and/or discrepancies between low-residue and low-fiber diets and on the diagnostic and therapeutic values of these diets in gastrointestinal disease management. Diagnostically, a low-fiber/low-residue diet is used in bowel preparation. A bowel preparation is a cleansing of the intestines of fecal matter and secretions conducted before a diagnostic procedure. Therapeutically, a low-fiber/low-residue diet is part of the treatment of acute relapses in different bowel diseases. The available evidence on low-residue and low-fiber diets is summarized. The main findings showed that within human disease research, the terms "low residue" and "low fiber" are used interchangeably, and information related to the quantity of residue in the diet usually refers to the amount of fiber. Low-fiber/low-residue diets are further explored in both diagnostic and therapeutic situations. On the basis of this literature review, the authors suggest redefining a low-residue diet as a low-fiber diet and to quantitatively define a low-fiber diet as a diet with a maximum of 10 g fiber/d. A low-fiber diet instead of a low-residue diet is recommended as a diagnostic value or as specific therapy for gastrointestinal conditions. © 2015 American Society for Nutrition.

Chlorpyrifos residual behaviors in field crops and transfers during duck pellet feed processing.

PubMed

Li, Rui; Wei, Wei; He, Liang; Hao, Lili; Ji, Xiaofeng; Zhou, Yu; Wang, Qiang

2014-10-22

Chlorpyrifos is a widely used organophosphorus pesticide in agricultural crops (including food) and animal feeds in China, resulting in heavy contamination. Many studies have focused on the food-processing effects on chlorpyrifos removal, but sufficient information is not observed for feed-processing steps. Here, chlorpyrifos residual behaviors in field crops and its transfers in duck pellet feed-processing steps were evaluated. In field trials, the highest residues for rice grain, shelled corn, and soybean seed were 12.0, 0.605, and 0.220 mg/kg, respectively. Residues of all rice grain and about half of shelled corn exceeded the maximum residue limits (MRLs) of China, and five soybean seeds exceeded the MRL of China. Chlorpyrifos residue was reduced 38.2% in brown rice after the raw rice grain was hulled. The residue in bran increased 71.2% after milling from brown rice. During the squashing step, the residue reduced 73.8% in soybean meal. The residues reduced significantly (23.7-36.8%) during the process of granulating for rice, maize, and soybean products. Comparatively, the grinding process showed only limited influence on chlorpyrifos removal (<10%). The residues of duck pellet feeds produced from highly contaminated raw materials of this study were 1.01 mg/kg (maize-soybean feed) and 3.20 mg/kg (rice-soybean feed), which were much higher than the generally accepted value (>0.1 mg/kg) for animal feeding. Chlorpyrifos residues were removed significantly by processing steps of pellet feeds, but the residue of raw materials was the determining factor for the safety of duck feeding.

76 FR 36349 - Diethylene Glycol MonoEthyl Ether (DEGEE); Exemption From the Requirement of a Tolerance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-22

... use on growing crops and raw agricultural commodities, without limitation. Huntsman, Dow AgroSciences... a maximum permissible level for residues of DEGEE on growing crops and raw agricultural commodities... antifreeze [[Page 36350

40 CFR 141.65 - Maximum residual disinfectant levels.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 141.65 Section 141.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS National Primary Drinking Water... only ground water not under the direct influence of surface water must comply with this subpart...

40 CFR 141.65 - Maximum residual disinfectant levels.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... 141.65 Section 141.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS National Primary Drinking Water... only ground water not under the direct influence of surface water must comply with this subpart...

40 CFR 141.65 - Maximum residual disinfectant levels.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... 141.65 Section 141.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS National Primary Drinking Water... only ground water not under the direct influence of surface water must comply with this subpart...

40 CFR 141.65 - Maximum residual disinfectant levels.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... 141.65 Section 141.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS National Primary Drinking Water... only ground water not under the direct influence of surface water must comply with this subpart...

Brain tissues volume measurements from 2D MRI using parametric approach

NASA Astrophysics Data System (ADS)

L'vov, A. A.; Toropova, O. A.; Litovka, Yu. V.

2018-04-01

The purpose of the paper is to propose a fully automated method of volume assessment of structures within human brain. Our statistical approach uses maximum interdependency principle for decision making process of measurements consistency and unequal observations. Detecting outliers performed using maximum normalized residual test. We propose a statistical model which utilizes knowledge of tissues distribution in human brain and applies partial data restoration for precision improvement. The approach proposes completed computationally efficient and independent from segmentation algorithm used in the application.

Determination of tylosin residues in pig tissues using high-performance liquid chromatography.

PubMed

De Liguoro, M; Anfossi, P; Angeletti, R; Montesissa, C

1998-06-01

In accordance with the maximum residue limit of 100 micrograms kg-1 established by EU legislation, a simple and sensitive high-performance liquid chromatographic (HPLC) method was developed for the measurement of tylosin residues in pig tissues (fat, kidney, liver and muscle). Tylosin, a macrolide antibiotic, is extracted with water-methanol and cleaned-up by solid-phase extraction (SPE) on cation-exchange cartridges using methanol elution. Tylosin was determined by reversed-phase HPLC with UV detection at 280 nm and the mean recovery from pig tissues fortified in the range 50-200 micrograms kg-1 was 70-85%, with intra- and inter-day RSDs in the ranges 3.4-9.1 and 3.9-10.1% respectively.

Portable surface plasmon resonance immunosensor for the detection of fluoroquinolone antibiotic residues in milk.

PubMed

Fernández, Fátima; Pinacho, Daniel G; Sánchez-Baeza, Francisco; Marco, M Pilar

2011-05-11

An inexpensive and portable surface plasmon resonance (SPR) sensor, SPReeta Evaluation Kit SPR3, has been used to develop a biosensor for the determination of fluoroquinolone antibiotics (FQs) and to demonstrate its performance analyzing FQ residues in milk samples. The SPReeta three-channel gold chips were activated with a mixed self-assembled monolayer (m-SAM) and functionalized with a FQ haptenized protein. Binding of the antibody produced a concentration-dependent increase of the SPR signal as a result of the change in the refraction index. Similarly, the presence of the FQ produced a dose-dependent decrease of the response, which allowed a good limit of detection (LOD) to be obtained (1.0 ± 0.4 μg L(-1) for enrofloxacin in buffer). The response was reproducible in all three channels, on different injections and days, and also between chips. Milk samples could be analyzed after a simple sample treatment involving fat removal by centrifugation and dilution with water. Under these conditions calibration curves were obtained showing that FQ residues can be analyzed in milk samples with an IC(50) value of 26.4 ± 7.2 μg L(-1) and a LOD of 2.0 ± 0.2 μg L(-1) (for enrofloxacin), far below the European Union regulations for this antibiotic family in this matrix. Finally, the paper also demonstrates that the biosensor is able to selectively detect the presence of FQs in milk samples, even in the presence of other antibiotics. Enrofloxacin, ciprofloxacin, and norfloxacin residues were detected in blind samples supplied by Nestlé Co.

Preliminary screening of ethnomedicinal plants from India.

PubMed

Perumal Samy, R; Ignacimuthu, S; Raja, D P

1999-08-01

Antibacterial activity of aqueous residues of 16 different ethnomedicinal plants have been studied. The effect of the aqueous extract at two different weights of plant residues, 30 and 40 mg, were tested against three gram positive bacteria and seven gram negative bacteria by the filter paper disc diffusion method. Among the tested plants, Cleome gynandropsis and Ageratum conyzoides showed a significant control of the growth of Alkaligens viscolactis, Klebsiella aerogenas, Bacillus cerues and Streptococcus pyogens. The maximum inhibitions were observed in Tridax procumbens, Cleome viscosa, Acalypha indica and Boerhaavia erecta against Aeromonas hydrophilla and Bacillus cerues.

Some New Estimation Methods for Weighted Regression When There are Possible Outliers.

DTIC Science & Technology

1985-01-01

about influential points, and to add to our understanding of the structure of the data In Section 2 we show, by considering the influence function , why... influence function lampel; 1968, 1974) for the maximum likelihood esti- mator is proportional to (EP-l)h(x), where £= (y-x’B)exp[-h’(x)e], and is thus...unbounded. Since the influence function for the MLE is quadratic in the residual c, in theory a point with a sufficiently large residual can have an

Characterization of Residual Stress in Microelectromechanical Systems (MEMS) Devices Using Raman Spectroscopy

DTIC Science & Technology

2002-04-01

residual and induced stress curves . A key to modelling MEMS structures, especially micromirrors , is to 2-23 (a) 0V (b) 10V (c) 20V (d) 40V (e) 50V (f...outlined in Figure 4.20. A line marker is used to extract the FEM data as displayed across the micromirror flexure. The MEMCAD FEM stress curve for the... curved as observed by the number of fringe lines displayed on the micromirror surface. The maximum peak deformation for this series of micromirrors is

Updated database on natural radioactivity in building materials in Europe.

PubMed

Trevisi, R; Leonardi, F; Risica, S; Nuccetelli, C

2018-07-01

The paper presents the latest collection of activity concentration data of natural radionuclides ( 226 Ra, 232 Th and 4  K) in building materials. This database contains about 24200 samples of both bulk materials and their constituents (bricks, concrete, cement, aggregates) and superficial materials used in most European Union Member States and some European countries. This collection also includes radiological information about some NORM residues and by-products (by-product gypsum, metallurgical slags, fly and bottom ashes and red mud) which can be of radiological concern if recycled in building materials as secondary raw materials. Moreover, radon emanation and radon exhalation rate data are reported for bricks and concrete. Copyright © 2018 Elsevier Ltd. All rights reserved.

Suitability of bovine bile compared to urine for detection of free, sulfate and glucuronate boldenone, androstadienedione, cortisol, cortisone, prednisolone, prednisone and dexamethasone by LC-MS/MS.

PubMed

Chiesa, Luca; Nobile, Maria; Panseri, Sara; Vigo, Daniele; Pavlovic, Radmila; Arioli, Francesco

2015-12-01

The administration of boldenone and androstadienedione to cattle is forbidden in the European Union, while prednisolone is permitted for therapeutic purposes. They are pseudoendogenous substances (endogenously produced under certain circumstances). The commonly used matrices in control analyses are urine or liver. With the aim of improving the residue controls, we previously validated a method for steroid analysis in bile. We now compare urine (a 'classic' matrix) to bile, both collected at the slaughterhouse, to understand whether the detection of steroids in the latter is easier. With the aim of having clearer results, we tested the presence of the synthetic corticosteroid dexamethasone. The results show that bile does not substantially improve the detection of boldenone, or its conjugates, prednisolone and prednisone. Dexamethasone, instead, was found in 10 out of 53 bovine bile samples, but only in one urine sample from the same animals. Bile could constitute a novel matrix for the analysis of residues in food-producing animals, and possibly not only of synthetic corticosteroids. Copyright © 2015 Elsevier Ltd. All rights reserved.

Authorization and Toxicity of Veterinary Drugs and Plant Protection Products: Residues of the Active Ingredients in Food and Feed and Toxicity Problems Related to Adjuvants

PubMed Central

Klátyik, Szandra; Bohus, Péter; Darvas, Béla; Székács, András

2017-01-01

Chemical substances applied in animal husbandry or veterinary medicine and in crop protection represent substantial environmental loads, and their residues occur in food and feed products. Product approval is governed differently in these two sectors in the European Union (EU), and the occurrence of veterinary drug (VD) and pesticide residues indicated by contamination notification cases in the Rapid Alert System for Food and Feed of the EU also show characteristic differences. While the initial high numbers of VD residues reported in 2002 were successfully suppressed to less than 100 cases annually by 2006 and on, the number of notification cases for pesticide residues showed a gradual increase from a low (approximately 50 cases annually) initial level until 2005 to more than 250 cases annually after 2009, with a halt occurring only in 2016. Main notifiers of VD residues include Germany, Belgium, the UK, and Italy (63, 59, 42, and 31 notifications announced, respectively), and main consigning countries of non-compliances are Vietnam, India, China, and Brazil (88, 50, 34, and 23 notifications, respectively). Thus, countries of South and Southeast Asia are considered a vulnerable point with regard to VD residues entering the EU market. Unintended side effects of VDs and plant protection products may be caused not only by the active ingredients but also by various additives in these preparations. Adjuvants (e.g., surfactants) and other co-formulants used in therapeutic agents and feed additives, as well as in pesticide formulations have long been considered as inactive ingredients in the aspects of the required main biological effect of the pharmaceutical or pesticide, and in turn, legal regulations of the approval and marketing of these additives specified significantly less stringent risk assessment requirements, than those specified for the active ingredients. However, numerous studies have shown additive, synergistic, or antagonistic side effects between the active ingredients and their additives in formulated products; moreover, toxicity has been evidenced for various additives. Therefore, toxicological evaluation of surfactants and other additives is essential for proper environmental risk assessment of formulations used in agriculture including animal husbandry and plant protection. PMID:28929103

Authorization and Toxicity of Veterinary Drugs and Plant Protection Products: Residues of the Active Ingredients in Food and Feed and Toxicity Problems Related to Adjuvants.

PubMed

Klátyik, Szandra; Bohus, Péter; Darvas, Béla; Székács, András

2017-01-01

Chemical substances applied in animal husbandry or veterinary medicine and in crop protection represent substantial environmental loads, and their residues occur in food and feed products. Product approval is governed differently in these two sectors in the European Union (EU), and the occurrence of veterinary drug (VD) and pesticide residues indicated by contamination notification cases in the Rapid Alert System for Food and Feed of the EU also show characteristic differences. While the initial high numbers of VD residues reported in 2002 were successfully suppressed to less than 100 cases annually by 2006 and on, the number of notification cases for pesticide residues showed a gradual increase from a low (approximately 50 cases annually) initial level until 2005 to more than 250 cases annually after 2009, with a halt occurring only in 2016. Main notifiers of VD residues include Germany, Belgium, the UK, and Italy (63, 59, 42, and 31 notifications announced, respectively), and main consigning countries of non-compliances are Vietnam, India, China, and Brazil (88, 50, 34, and 23 notifications, respectively). Thus, countries of South and Southeast Asia are considered a vulnerable point with regard to VD residues entering the EU market. Unintended side effects of VDs and plant protection products may be caused not only by the active ingredients but also by various additives in these preparations. Adjuvants (e.g., surfactants) and other co-formulants used in therapeutic agents and feed additives, as well as in pesticide formulations have long been considered as inactive ingredients in the aspects of the required main biological effect of the pharmaceutical or pesticide, and in turn, legal regulations of the approval and marketing of these additives specified significantly less stringent risk assessment requirements, than those specified for the active ingredients. However, numerous studies have shown additive, synergistic, or antagonistic side effects between the active ingredients and their additives in formulated products; moreover, toxicity has been evidenced for various additives. Therefore, toxicological evaluation of surfactants and other additives is essential for proper environmental risk assessment of formulations used in agriculture including animal husbandry and plant protection.

Risk-based approach to developing a national residue sampling plan for testing under European Union regulation for veterinary medicinal products and coccidiostat feed additives in domestic animal production.

PubMed

Danaher, Martin; Shanahan, Conor; Butler, Francis; Evans, Rhodri; O'Sullivan, Dan; Glynn, Denise; Camon, Tim; Lawlor, Peadar; O'Keeffe, Michael

2016-07-01

A ranking system for veterinary medicinal products and coccidiostat feed additives has been developed as a tool to be applied in a risk-based approach to the residue testing programme for foods of animal origin in the Irish National Residue Control Plan (NRCP). Three characteristics of substances that may occur as residues in food are included in the developed risk ranking system: Potency, as measured by the acceptable daily intake assigned by the European Medicines Agency Committee for Medicinal Products for Veterinary Use, to each substance; Usage, as measured by the three factors of Number of Doses, use on Individual animals or for Group treatment, and Withdrawal Period; and Residue Occurrence, as measured by the number of Non-Compliant Samples in the NRCP. For both Number of Doses and Non-Compliant Samples, data for the 5-year period 2008-12 have been used. The risk ranking system for substances was developed for beef cattle, sheep and goats, pigs, chickens and dairy cattle using a scoring system applied to the various parameters described above to give an overall score based on the following equation: Potency × Usage (Number of Doses + Individual/Group Use + Withdrawal Period) × Residue Occurrence. Applying this risk ranking system, the following substances are ranked very highly: antimicrobials such as amoxicillin (for all species except pigs), marbofloxacillin (for beef cattle), oxytetracycline (for all species except chickens), sulfadiazine with trimethoprim (for pigs and chickens) and tilmicosin (for chickens); antiparasitic drugs, such as the benzimidazoles triclabendazole (for beef and dairy cattle), fenbendazole/oxfendazole (for sheep/goats and dairy cattle) and albendazole (for dairy cattle), the avermectin ivermectin (for beef cattle), and anti-fluke drugs closantel and rafoxanide (for sheep/goats); the anticoccidials monensin, narasin, nicarbazin and toltrazuril (for chickens). The risk ranking system described is a relatively simple system designed to provide a reliable basis for selecting the veterinary medicinal products and coccidiostat feed additives that might be prioritised for residue testing.

[Three-dimensional stress analysis of periodontal ligament of mandible incisors fixed bridge abutments under dynamic loads by finite element method].

PubMed

Ma, Da; Tang, Liang; Pan, Yan-Huan

2007-12-01

Three-dimensional finite method was used to analyze stress and strain distributions of periodontal ligament of abutments under dynamic loads. Finite element analysis was performed on the model under dynamic loads with vertical and oblique directions. The stress and strain distributions and stress-time curves were analyzed to study the biomechanical behavior of periodontal ligament of abutments. The stress and strain distributions of periodontal ligament under dynamic load were same with the static load. But the maximum stress and strain decreased apparently. The rate of change was between 60%-75%. The periodontal ligament had time-dependent mechanical behaviors. Some level of residual stress in periodontal ligament was left after one mastication period. The stress-free time under oblique load was shorter than that of vertical load. The maximum stress and strain decrease apparently under dynamic loads. The periodontal ligament has time-dependent mechanical behaviors during one mastication. There is some level of residual stress left after one mastication period. The level of residual stress is related to the magnitude and the direction of loads. The direction of applied loads is one important factor that affected the stress distribution and accumulation and release of abutment periodontal ligament.

Detailed measured sections, cross sections, and paleogeographic reconstructions of the upper cretaceous and lower tertiary nonmarine interval, Wind River Basin, Wyoming: Chapter 10 in Petroleum systems and geologic assessment of oil and gas resources in the Wind River Basin Province, Wyoming

USGS Publications Warehouse

Johnson, Ronald C.

2007-01-01

Detailed measured sections and regional stratigraphic cross sections are used to reconstruct facies maps and interpret paleogeographic settings for the interval from the base of Upper Cretaceous Mesaverde Formation to top of lower member of the Paleocene Fort Union Formation in the Wind River Basin, Wyoming. The Mesaverde Formation spans the time during which the Upper Cretaceous seaway retreated eastward out of central Wyoming in Campanian time and the initial stages of the Lewis transgression in earliest Maastrichtian time. This retreat stalled for a considerable period of time during deposition of the lower part of the Mesaverde, creating a thick buildup of marginal marine sandstones and coaly coastal plain deposits across the western part of the basin. The Lewis sea transgressed into the northeast part of Wind River Basin, beginning in early Maastrichtian time during deposition of the Teapot Sandstone Member of the Mesaverde Formation. The Meeteetse Formation, which overlies the Teapot, was deposited in a poorly-drained coastal plain setting southwest of the Lewis seaway. The Lewis seaway, at maximum transgression, covered much of the northeast half of the Wind River Basin area but was clearly deflected around the present site of the Wind River Range, southwest of the basin, providing the first direct evidence of Laramide uplift on that range. Uplift of the Wind River Range continued during deposition of the overlying Maastrichtian Lance Formation. The Granite Mountains south of the basin also became a positive feature during this time. A rapidly subsiding trough during the Maastrichtian time formed near the presentday trough of the Wind River Basin in which more than 6,000 feet of Lance was deposited. The development of this trough appears to have begun before the adjacent Owl Creek Mountains to the north started to rise; however, a muddy facies in the upper part of Lance in the deep subsurface, just to the south, might be interpreted to indicate that the Cretaceous Cody Shale was being eroded off a rising Owl Creek Mountains in latest Cretaceous time. The Paleocene Fort Union Formation unconformably overlies older units but with only slight angular discordance around much of the margins of the Wind River Basin. Pre-Fort Union erosion was most pronounced toward the Wind River Range to the southwest, where the Fort Union ultimately overlies strata as old as the upper part of the Cretaceous Cody Shale. The unconformity appears to die out toward the basin center. Coal-forming mires developed throughout the western part of the basin near the beginning of the Paleocene. River systems entering the basin from the Wind River Range to the southwest and the Granite Mountains to the south produced areas of sandy fluvial deposition along mountain fronts. A major river system appears to have entered the basin from about the same spot along the Wind River Range throughout much of the Paleocene, probably because it became incised and could not migrate laterally. The muddy floodplain facies that developed along the deep basin trough during latest Cretaceous time, expanded during the early part of the Paleocene. Coal-forming mires that characterize part of the lower Fort Union Formation reached maximum extent near the beginning of the late Paleocene and just prior to the initial transgression of Lake Waltman. From the time of initial flooding, Lake Waltman expanded rapidly, drowning the coal-forming mires in the central part of the basin and spreading to near basin margins. Outcrop studies along the south margin of the basin document that once maximum transgression was reached, the lake was rapidly pushed basinward and replaced by fluvial environments.

An investigation of shoulder forces in active shoulder tackles in rugby union football.

PubMed

Usman, Juliana; McIntosh, Andrew S; Fréchède, Bertrand

2011-11-01

In rugby union football the tackle is the most frequently executed skill and one most associated with injury, including shoulder injury to the tackler. Despite the importance of the tackle, little is known about the magnitude of shoulder forces in the tackle and influencing factors. The objectives of the study were to measure the shoulder force in the tackle, as well as the effects of shoulder padding, skill level, side of body, player size, and experimental setting on shoulder force. Experiments were conducted in laboratory and field settings using a repeated measures design. Thirty-five participants were recruited to the laboratory and 98 to the field setting. All were male aged over 18 years with rugby experience. The maximum force applied to the shoulder in an active shoulder tackle was measured with a custom built forceplate incorporated into a 45 kg tackle bag. The overall average maximum shoulder force was 1660 N in the laboratory and 1997 N in the field. This difference was significant. The shoulder force for tackling without shoulder pads was 1684 N compared to 1635 N with shoulder pads. There was no difference between the shoulder forces on the dominant and non-dominant sides. Shoulder force reduced with tackle repetition. No relationship was observed between player skill level and size. A substantial force can be applied to the shoulder and to an opponent in the tackle. This force is within the shoulder's injury tolerance range and is unaffected by shoulder pads. Copyright © 2011 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

A meta-analysis of injuries in senior men's professional Rugby Union.

PubMed

Williams, Sean; Trewartha, Grant; Kemp, Simon; Stokes, Keith

2013-10-01

Rugby Union has one of the highest reported incidences of match injuries amongst all professional team sports. The majority of research within this field has focused on elite male cohorts; in this study we present the first meta-analytic review of these data. The aim of this study was to summarise the incidence and severity of injuries in senior men's professional Rugby Union, and determine the overall effects of level of play, new versus recurrent injuries, playing position, type of injuries, location of injuries, severity of injuries, period of match, and injury incident. Electronic databases were searched using keywords 'Rugby Union' and 'inj*'. Fifteen papers addressing injuries in senior men's professional Rugby Union (from 1995 through September 2012) were included in the review. A maximum of ten of these papers provided incidence data that could be modelled via a Poisson mixed-effects generalised linear model, while up to nine studies provided severity data that could be modelled via a general linear mixed model. Magnitude based inferences were used to assess differences between factors. A descriptive analysis was provided for studies that could not be included in the pooled analysis due to incongruent injury definitions. The overall incidence of injuries in senior men's professional Rugby Union matches was 81 per 1,000 player hours (95 % CI 63-105), and 3 per 1,000 player hours (95 % CI 2-4) during training. Estimated mean severity for match injuries was 20 days (95 % CI 14-27), and 22 days (95 % CI 19-24) for training injuries. A higher level of play was associated with a greater incidence of injuries in matches, with no clear difference in severity. New injuries occurred substantially more often than recurrent injuries, while the severity of recurrent injuries was, on average, 10 days (95 % CI 4-17) greater than new injuries. Trivial differences were found in injury incidence and severity between forwards and backs. Muscle/tendon and joint (non-bone)/ligament injuries were the two most prevalent injury groups, whereas fractures and bone stress injuries had the highest average severity. The lower limb was the body region with the highest injury incidence, while upper limb injuries were most severe. The third quarter (40-60 min) of matches had the highest injury rate, and injuries most commonly occurred as a result of being tackled. This meta-analysis confirms match injury incidence rates in professional Rugby Union can be considered high in comparison with other team sports, but similar to other collision sports. In order to markedly reduce overall injury burden, efforts should target lower-limb injury prevention strategies and technique during contact, as these may render the largest effect.

Limits and regulations for mycotoxins in food and feed.

PubMed

Zmudzki, J; Wiśniewska-Dmytrow, H

2004-01-01

Mycotoxins are natural contaminants whose presence in food- and feedstuffs cannot be completely avoided. Since several mycotoxins have been associated with and implicated in human and animal diseases there is a need to establish maximum levels, guidelines or action levels for them in some kinds of commodities. International and government authorities in many countries have been investing in mycotoxins research and initiating administrative actions for elaboration of legislation and implementing regulatory measures for the control of mycotoxins. Codex Alimentarius Commission is established international legislation on food and feed. In European Union specific limits and regulations for mycotoxins and other contaminants are constructed under the general Codex standards and based on proposal from European Commission. The legal basis for European Commission became available with the framework Council Regulation (EEC) No 315/93. In this paper, legislation regarding maximum levels for certain mycotoxins in food- and feedstuffs in European Community and other countries were reviewed and discussed.

Land use/land cover change effects on temperature trends at U.S. Climate Normals stations

USGS Publications Warehouse

Hale, R.C.; Gallo, K.P.; Owen, T.W.; Loveland, Thomas R.

2006-01-01

Alterations in land use/land cover (LULC) in areas near meteorological observation stations can influence the measurement of climatological variables such as temperature. Urbanization near climate stations has been the focus of considerable research attention, however conversions between non-urban LULC classes may also have an impact. In this study, trends of minimum, maximum, and average temperature at 366 U.S. Climate Normals stations are analyzed based on changes in LULC defined by the U.S. Land Cover Trends Project. Results indicate relatively few significant temperature trends before periods of greatest LULC change, and these are generally evenly divided between warming and cooling trends. In contrast, after the period of greatest LULC change was observed, 95% of the stations that exhibited significant trends (minimum, maximum, or mean temperature) displayed warming trends. Copyriht 2006 by the American Geophysical Union.

Nonylphenol: Properties, legislation, toxicity and determination.

PubMed

Araujo, Frederico G DE; Bauerfeldt, Glauco F; Cid, Yara Peluso

2017-08-07

This paper aims to gather and discuss important information about nonylphenol, such as physical chemistry properties, toxicity and analytical methods in various matrices. As a degradation product of ethoxylated alkylphenols, nonylphenol presents a higher degree of reactivity than its precursor. Due to its harmful effects on the environment, use and production of nonylphenol has been banned in European Union countries, alongside their precursors. The guide on quality of drinking water (USEPA) recommends a maximum concentration of 28 µg L-1 for fresh water. In Brazil, there is no clear legislation containing values ​​of maximum concentration of nonylphenol. Due to this lack of regulation, a continuous monitoring is necessary of this pollutant in environmental samples. This paper aims to encourage further studies on nonylphenol, seen as a critical environmental pollutant. For proper monitoring is necessary to have reliable analytical methods and easy to perform in routine analysis.

Determination of Pesticides Residues in Cucumbers Grown in Greenhouse and the Effect of Some Procedures on Their Residues.

PubMed

Leili, Mostafa; Pirmoghani, Amin; Samadi, Mohammad Taghi; Shokoohi, Reza; Roshanaei, Ghodratollah; Poormohammadi, Ali

2016-11-01

The objective of this study was to determine the residual concentrations of ethion and imidacloprid in cucumbers grown in greenhouse. The effect of some simple processing procedures on both ethion and imidacloprid residues were also studied. Ten active greenhouses that produce cucumber were randomly selected. Ethion and imidacloprid as the most widely used pesticides were measured in cucumber samples of studied greenhouses. Moreover, the effect of storing, washing, and peeling as simple processing procedures on both ethion and imidacloprid residues were investigated. One hour after pesticide application; the maximum residue levels (MRLs) of ethion and imidacloprid were higher than that of Codex standard level. One day after pesticide application, the levels of pesticides were decreased about 35 and 31% for ethion and imidacloprid, respectively, which still were higher than the MRL. Washing procedure led to about 51 and 42.5% loss in ethion and imidacloprid residues, respectively. Peeling procedure also led to highest loss of 93.4 and 63.7% in ethion and imidacloprid residues, respectively. The recovery for both target analytes was in the range between 88 and 102%. The residue values in collected samples one hour after pesticides application were higher than standard value. The storing, washing, and peeling procedures lead to the decrease of pesticide residues in greenhouse cucumbers. Among them, the peeling procedure has the greatest impact on residual reduction. Therefore, these procedures can be used as simple and effective processing techniques for reducing and removing pesticides from greenhouse products before their consumption.

How effective are common household preparations on removing pesticide residues from fruit and vegetables? A review.

PubMed

Chung, Stephen Wc

2018-06-01

Nowadays, the use of pesticides is inevitable for pest control in crops, especially for fruit and vegetables. After the harvest from raw agricultural commodities, the amount of pesticide residues in food is mainly influenced by the storage, handling and processing that follow. If good agricultural and good manufacturing practices are enforced effectively, the amount of pesticide residues would be brought below the corresponding maximum residue level. Thus, the consumption of raw and/or prepared fruit and vegetables would be safe. Nonetheless, reports regarding pesticide residues in fruit or vegetables on mass media have been worrying consumers, who are concerned about the adverse effects of pesticide residues. As a result, consumers perform household processing before consumption to reduce any related risks. However, can these preparations effectively remove pesticide residues? Reviewing the extensive literature, it showed that, in most cases, washing and soaking can only lead to a certain degree of reduction in residue level, while other processing such as peeling, soaking in chemical baths and blanching can reduce pesticide residues more effectively. In general, the behaviour of residues during processing can be rationalised in terms of the physico-chemical properties of the pesticide and the nature of the process. In contrast, the reported studies are diversified and some areas still lack sufficient studies to draw any remarks. Recommendations are provided with respect to the available information that aims to formulate an environmental friendly, cost-effective and efficient household processing of fruit and vegetables to reduce pesticide residues. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Inventory of heavy metal content in organic waste applied as fertilizer in agriculture: evaluating the risk of transfer into the food chain.

PubMed

Lopes, Carla; Herva, Marta; Franco-Uría, Amaya; Roca, Enrique

2011-07-01

In this work, an environmental risk assessment of reusing organic waste of differing origins and raw materials as agricultural fertilizers was carried out. An inventory of the heavy metal content in different organic wastes (i.e., compost, sludge, or manure) from more than 80 studies at different locations worldwide is presented. The risk analysis was developed by considering the heavy metal (primarily Cd, Cu, Ni, Pb, and Zn) concentrations in different organic residues to assess their potential environmental accumulation and biotransfer to the food chain and humans. A multi-compartment model was used to estimate the fate and distribution of metals in different environmental compartments, and a multi-pathway model was used to predict human exposure. The obtained hazard index for each waste was concerning in many cases, especially in the sludge samples that yielded an average value of 0.64. Among the metals, Zn was the main contributor to total risk in all organic wastes due to its high concentration in the residues and high biotransfer potential. Other more toxic metals, like Cd or Pb, represented a negligible contribution. These results suggest that the Zn content in organic waste should be reduced or more heavily regulated to guarantee the safe management and reuse of waste residues according to the current policies promoted by the European Union.

Residue level and dissipation of carbendazim in/on pomegranate fruits and soil.

PubMed

Mohapatra, Soudamini; S, Lekha

2016-07-01

Carbendazim is widely used on pomegranate for control of a large number of fungal diseases. Its residue levels in/on pomegranate fruits and soil were evaluated under field conditions. The quick, easy, cheap, effective, rugged, and safe (QuEChERS) method in conjunction with liquid-chromatography mass spectrometry was used for analysis of carbendazim. Recovery of carbendazim was within 78.92-96.28 % and relative standard deviation within 3.8-10.9 % (n = 6). Carbendazim residues on pomegranate fruits dissipated at the half lives of 17.3 and 22.8 days from treatments at 500 and 1000 g active ingredient (a.i.) ha(-1), respectively. Its residues in pomegranate aril were highest on the tenth day and reduced thereafter. The residue level of carbendazim on pomegranate whole fruits from standard dose treatment was less than the EU maximum residue limit (MRL) of 0.1 mg kg(-1) at harvest. The carbendazim residues were

Pesticide residues in Portuguese strawberries grown in 2009-2010 using integrated pest management and organic farming.

PubMed

Fernandes, Virgínia C; Domingues, Valentina F; Mateus, Nuno; Delerue-Matos, Cristina

2012-11-01

Pesticides are among the most widely used chemicals in the world. Because of the widespread use of agricultural chemicals in food production, people are exposed to low levels of pesticide residues through their diets. Scientists do not yet have a total understanding of the health effects of these pesticide residues. This work aims to determine differences in terms of pesticide residue content in Portuguese strawberries grown using different agriculture practices. The Quick, Easy, Cheap, Effective, Rugged, and Safe sample preparation method was conducted and shown to have good performance for multiclass pesticides extraction in strawberries. The screening of 25 pesticides residue was performed by gas chromatography-tandem mass spectrometry. In quantitative validation, acceptable performances were achieved with recoveries of 70-120 and <12 % residual standard deviation for 25 pesticides. Good linearity was obtained for all the target compounds, with highly satisfactory repeatability. The limits of detection were in the range of 0.1-28 μg/kg. The method was applied to analyze strawberry samples from organic and integrated pest management (IPM) practices harvested in 2009-2010. The results showed the presence of fludioxonil, bifenthrin, mepanipyrim, tolylfluanid, cyprodinil, tetraconazole, and malathion when using IPM below the maximum residue levels.

Effect of processing on the disappearance of pesticide residues in fresh-cut lettuce: Bioavailability and dietary risk.

PubMed

Camara, Miguel A; Barba, Alberto; Cermeño, Sandra; Martinez, Gracia; Oliva, Jose

2017-12-02

The aim of this research is to establish the processing factors of six pesticides durong the preparation of fresh-cut lettuce and to assess the risk of ingestion of pesticide residues associated with the consumption of the same. A field study was carried out on the dissipation of three insecticides (imidacloprid, tebufenozide, cypermethrin) and three fungicides (metalaxyl, tebuconazole, azoxystrobin) during treatment conditions simulating those used for commercial fresh-cut lettuce. A simultaneous residue analysis method is validated using QuEChERS extraction with acetonitrile and CG-MS and LC-MS/MS analysis. The residues detected after field application never exceed the established Maximum Residue Limits. The processing factors were generally less than 1 (between 0.34 for tebufenozide and 0.53 for imidacloprid), indicating that the process, as a whole, considerably reduces residue levels in processed lettuce compared to fresh lettuce. It is confirmed that cutting, followed by washing and drying, considerably reduces the residues. A matrix effect in the dialyzation of the pesticides is observed and the in vitro study of bioavailability establishes a low percentage of stomach absorption capacity (<15%). The EDI/ADI ratios found in all cases were well below their ADI values, and the dietary exposure assessed (EDI) in fresh-cut lettuce showed no concerns for consumer health.

Residues of aflatoxin B1 in broiler meat: effect of age and dietary aflatoxin B1 levels.

PubMed

Hussain, Zahid; Khan, Muhammad Zargham; Khan, Ahrar; Javed, Ijaz; Saleemi, Muhammad Kashif; Mahmood, Sultan; Asi, Muhammad Rafique

2010-12-01

This study describes the effect of dietary levels of aflatoxin B1 (AFB1) and age of the birds upon the residue level in liver and muscles of broiler chicks. In three different experiments broiler chicks of 7, 14 and 28 days of age were kept for 7 days on contaminated rations having 1600, 3200 and 6400 μg/kg AFB1. AFB1 residues were detected earlier in younger birds and those fed high AFB1 dietary levels. The highest residue levels in liver and muscles of young chicks fed 6400 μg/kg AFB1 was 6.97±0.08 and 3.27±0.05 ng/g, respectively. Maximum residue concentration was high in birds of young age and those kept on high AFB1 ration. After withdrawal of AF contaminated rations, residues clearance was slow and AFB1 was detectable in liver and muscles of birds for longer duration in younger birds and those fed high AFB1 dietary levels. AFB1 residues in poultry tissues may buildup to high levels in areas with no regulatory limits on AFB1 levels of poultry feed and may pose a risk to consumers health. Copyright © 2010 Elsevier Ltd. All rights reserved.

Pyrethroids in chicken eggs from commercial farms and home production in Rio de Janeiro: Estimated daily intake and diastereomeric selectivity.

PubMed

Parente, Cláudio E T; Lestayo, Julliana; Guida, Yago S; Azevedo-Silva, Claudio E; Torres, João Paulo M; Meire, Rodrigo O; Malm, Olaf

2017-10-01

In this study, pyrethroids were determined in chicken eggs from commercial farm (n = 60) and home egg production (n = 30). These pyrethroids were investigated: bifenthrin, phenothrin, permethrin, cyfluthrin, cypermethrin and fenvalerate, including most diastereomers. Quantification was done using GC-MS in a negative chemical ionization mode. Pyrethroids residues were found in 79% of the analyzed samples. Cypermethrin presented the highest occurrence, being quantified in 62 samples (69%) in concentrations (lipid weight - l w.) varying between 0.29 and 6408 ng g -1 , followed by phenothrin (24%), 21-3910 ng g -1 , permethrin (14%), 2.96-328 ng g -1 , and bifenthrin (11%), 3.77-16.7 ng g -1 . Cyfluthrin and fenvalerate were not detected. Home-produced eggs had a higher occurrence of pyrethroids (97%), with a greater predominance of phenothrin. In commercial production, 70% of the samples presented pyrethroid residues (predominantly cypermethrin). This is the first report about the presence of pyrethroids in home-produced eggs and the first description of a selectivity pattern with the predominance of cis diastereomers in chicken eggs. In general, estimated daily intake does not present a risk to human consumption, according to Brazilian and international standards (FAO/WHO). However, one third of the samples (30 eggs) had concentrations above the maximum residue limits (MRLs). The maximum cypermethrin concentration was 66 times the MRL, while the maximum phenothrin concentration was 11 times the limit. Further studies about transfer dynamics, bioaccumulation and metabolic degradation of stereoisomers are required, as well as determining if this selectivity pattern in food can increase consumer's health risk. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evolution of residual stress, free volume, and hardness in the laser shock peened Ti-based metallic glass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Liang; Wang, Lu; Nie, Zhihua

Laser shock peening (LSP) with different cycles was performed on the Ti-based bulk metallic glasses (BMGs). The sub-surface residual stress of the LSPed specimens was measured by high-energy X-ray diffraction (HEXRD) and the near-surface residual stress was measured by scanning electron microscope/focused ion beam (SEM/FIB) instrument. The sub-surface residual stress in the LSP impact direction (about-170MPa) is much lower than that perpendicular to the impact direction (about -350 MPa), exhibiting anisotropy. The depth of the compressive stress zone increases from 400 mu m to 500 mu m with increasing LSP cycles. The highest near-surface residual stress is about -750 MPa.more » LSP caused the free volume to increase and the maximum increase appeared after the first LSP process. Compared with the hardness (567 +/- 7 HV) of the as-cast BMG, the hardness (590 +/- 9 HV) on the shocked surface shows a hardening effect due to the hardening mechanism of compressive residual stress; and the hardness (420 +/- 9 HV) on the longitudinal section shows a softening effect due to the softening mechanism of free volume.« less

Pesticide Residue Monitoring on South African Fresh Produce Exported over a 6-Year Period.

PubMed

Mutengwe, M T; Chidamba, L; Korsten, L

2016-10-01

Six years of pesticide residue data from fresh produce destined for the export market were analyzed for the period 2009 to 2014. A total of 37,838 fruit (99.27%) and vegetable (0.73%) data sets analyzed for the presence of 73 pesticides were compared. Pesticides were detected on 56.46% of samples, of which 0.78% had multiple residues. Noncompliances detected were because of the use of unregistered pesticides (0.73%), values that exceeded established maximum residue levels (MRLs) (0.32%), or the combination of values that exceeded MRLs and the use of unregistered pesticide residues (0.003%). The most commonly detected pesticides that exceeded established MRLs were imazalil (37.71%), prochloraz (28.69%), and iprodione (5.74%). The unregistered pesticide most often found on grapes and avocados was also imazalil (62.23%) and, on nectarines and avocados, diphenylamine (11.15%). Exceedances of MRL values were mostly associated with oranges (43.44%), avocados (27.87%), grapefruits (7.38%), and lemons (6.56%). Residual pesticide monitoring on fruits and vegetables is a key tool to ensure conformity with regulatory requirements and compliance with good agricultural practices and the trade requirements set by the importing country.

Reported community-level indoor residual spray coverage from two-stage cluster surveys in sub-Saharan Africa.

PubMed

Larsen, David A; Borrill, Lauren; Patel, Ryan; Fregosi, Lauren

2017-06-13

Malaria is an important cause of morbidity and mortality in malaria-endemic areas. Indoor residual spray is an effective intervention to control malaria, but high community-level coverage is needed to maximize its impact. Using thirty-four two-stage cluster surveys (e.g., demographic and health surveys) and lot quality assurance sampling, indoor residual spray was estimated at the community level (i.e. enumeration-area) across sub-Saharan Africa since 2010. For communities receiving indoor residual spray a logistic regression predicted whether community-level coverage exceeded 50% or not. Household-level coverage was equitable both in terms of wealth and urban/rural, with poorer and rural houses more likely to be sprayed than richer and urban houses. Coverage of indoor residual spray at the community level is poor across the continent, with 54% of communities receiving the intervention not reaching 50% coverage. Having >50% coverage at the community-level was not associated with increasing the number of houses sprayed in the country. Implementation and monitoring of indoor residual coverage at small geographical scales need to improve greatly to receive maximum benefit of the intervention.

Residual stress measurement of PMMA by combining drilling-hole with digital speckle correlation method

NASA Astrophysics Data System (ADS)

Yao, X. F.; Xiong, T. C.; Xu, H. M.; Wan, J. P.; Long, G. R.

2008-11-01

The residual stresses of the PMMA (polymethyl methacrylate) specimens after being drilled, reamed and polished respectively are investigated using the digital speckle correlation experimental method,. According to the displacement fields around the correlated calculated region, the polynomial curve fitting method is used to obtain the continuous displacement fields, and the strain fields can be obtained from the derivative of the displacement fields. Considering the constitutive equation of the material, the expression of the residual stress can be presented. During the data processing, according to the fitting effect of the data, the calculation region of the correlated speckles and the degree of the polynomial fitting curve is decided. These results show that the maximum stress is at the hole-wall of the drilling hole specimen and with the increasing of the diameter of the drilled hole, the residual stress resulting from the hole drilling increases, whereas the process of reaming and polishing hole can reduce the residual stress. The relative large discrete degree of the residual stress is due to the chip removal ability of the drill bit, the cutting feed of the drill and other various reasons.

Semen quality and sex hormones with reference to metal welding.

PubMed

Hjollund, N H; Bonde, J P; Jensen, T K; Ernst, E; Henriksen, T B; Kolstad, H A; Giwercman, A; Skakkebaek, N E; Olsen, J

1998-01-01

Welding may involve hazards to the male reproductive system, but previous studies of semen quality have produced inconsistent results. We studied the effects of welding on markers of semen quality in a Danish nationwide sample of 430 first-time pregnancy planners without earlier reproductive experience. Couples were recruited among members of the union of metal workers and three other trade unions and were followed from termination of birth control until pregnancy for a maximum of six menstrual cycles. The males provided semen samples in each cycle. Median sperm density for welders was 56 x 10(6)/mL (52.5 x 10(6)/mL and 50.0 x 10(6)/mL in two reference groups). No statistically significant differences attributable to welding were found in proportions of morphologically normal sperm, sperm motility assessed by computer-aided sperm analysis, or sex hormones (testosterone, follicle-stimulating hormone, and luteinizing hormone). These negative findings may not apply to populations with high-level exposure to welding fume or to welders exposed to other putative hazards, e.g., heat.

Impact of socioeconomic status on municipal solid waste generation rate.

PubMed

Khan, D; Kumar, A; Samadder, S R

2016-03-01

The solid waste generation rate was expected to vary in different socioeconomic groups due to many environmental and social factors. This paper reports the assessment of solid waste generation based on different socioeconomic parameters like education, occupation, income of the family, number of family members etc. A questionnaire survey was conducted in the study area to identify the different socioeconomic groups that may affect the solid waste generation rate and composition. The average waste generated in the municipality is 0.41 kg/capita/day in which the maximum waste was found to be generated by lower middle socioeconomic group (LMSEG) with average waste generation of 0.46 kg/capita/day. Waste characterization indicated that there was no much difference in the composition of wastes among different socioeconomic groups except ash residue and plastic. Ash residue is found to increase as we move lower down the socioeconomic groups with maximum (31%) in lower socioeconomic group (LSEG). The study area is a coal based city hence application of coal and wood as fuel for cooking in the lower socioeconomic group is the reason for high amount of ash content. Plastic waste is maximum (15%) in higher socioeconomic group (HSEG) and minimum (1%) in LSEG. Food waste is a major component of generated waste in almost every socioeconomic group with maximum (38%) in case of HSEG and minimum (28%) in LSEG. This study provides new insights on the role of various socioeconomic parameters on generation of household wastes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Roles of basic amino acid residues in the activity of μ-conotoxin GIIIA and GIIIB, peptide blockers of muscle sodium channels.

PubMed

Sato, Kazuki; Yamaguchi, Yoko; Ishida, Yukisato; Ohizumi, Yasushi

2015-04-01

To study in detail the roles of basic amino acid residues in the activity of μ-conotoxin GIIIA (μ-GIIIA) and GIIIB (μ-GIIIB), specific blockers of muscle sodium channels, seven analogs of μ-GIIIA, and two analogs of μ-GIIIB were synthesized. μ-GIIIA analogs were synthesized by replacing systematically the three Arg residues (Arg1, Arg13, and Arg19) with one, two, and three Lys residues. μ-GIIIB analogs were synthesized by replacing simultaneously all four Lys residues (Lys9, Lys11, Lys16, and Lys19) with Arg residues and further replacement of acidic Asp residues with neutral Ala residues. Circular dichroism spectra of the synthesized analogs suggested that the replacement did not affect the three dimensional structure. The inhibitory effects on the twitch contractions of the rat diaphragm showed that the side chain guanidino group of Arg13 of μ-GIIIA was important for the activity, whereas that of Arg19 had little role for biological activity. Although [Arg9,11,16,19]μ-GIIIB showed higher activity than native μ-GIIIB, highly basic [Ala2,12, Arg9,11,16,19]μ-GIIIB showed lower activity, suggesting that there was an appropriate molecular basicity for the maximum activity. © 2014 John Wiley & Sons A/S.

Improving protein-protein interaction prediction using evolutionary information from low-quality MSAs.

PubMed

Várnai, Csilla; Burkoff, Nikolas S; Wild, David L

2017-01-01

Evolutionary information stored in multiple sequence alignments (MSAs) has been used to identify the interaction interface of protein complexes, by measuring either co-conservation or co-mutation of amino acid residues across the interface. Recently, maximum entropy related correlated mutation measures (CMMs) such as direct information, decoupling direct from indirect interactions, have been developed to identify residue pairs interacting across the protein complex interface. These studies have focussed on carefully selected protein complexes with large, good-quality MSAs. In this work, we study protein complexes with a more typical MSA consisting of fewer than 400 sequences, using a set of 79 intramolecular protein complexes. Using a maximum entropy based CMM at the residue level, we develop an interface level CMM score to be used in re-ranking docking decoys. We demonstrate that our interface level CMM score compares favourably to the complementarity trace score, an evolutionary information-based score measuring co-conservation, when combined with the number of interface residues, a knowledge-based potential and the variability score of individual amino acid sites. We also demonstrate, that, since co-mutation and co-complementarity in the MSA contain orthogonal information, the best prediction performance using evolutionary information can be achieved by combining the co-mutation information of the CMM with co-conservation information of a complementarity trace score, predicting a near-native structure as the top prediction for 41% of the dataset. The method presented is not restricted to small MSAs, and will likely improve interface prediction also for complexes with large and good-quality MSAs.

Natural deep eutectic solvent mediated pretreatment of rice straw: bioanalytical characterization of lignin extract and enzymatic hydrolysis of pretreated biomass residue.

PubMed

Kumar, Adepu K; Parikh, Bhumika S; Pravakar, Mohanty

2016-05-01

The present investigation demonstrated pretreatment of lignocellulosic biomass rice straw using natural deep eutectic solvents (NADESs), and separation of high-quality lignin and holocellulose in a single step. Qualitative analysis of the NADES extract showed that the extracted lignin was of high purity (>90 %), and quantitative analysis showed that nearly 60 ± 5 % (w/w) of total lignin was separated from the lignocellulosic biomass. Addition of 5.0 % (v/v) water during pretreatment significantly enhanced the total lignin extraction, and nearly 22 ± 3 % more lignin was released from the residual biomass into the NADES extract. X-ray diffraction studies of the untreated and pretreated rice straw biomass showed that the crystallinity index ratio was marginally decreased from 46.4 to 44.3 %, indicating subtle structural alterations in the crystalline and amorphous regions of the cellulosic fractions. Thermogravimetric analysis of the pretreated biomass residue revealed a slightly higher T dcp (295 °C) compared to the T dcp (285 °C) of untreated biomass. Among the tested NADES reagents, lactic acid/choline chloride at molar ratio of 5:1 extracted maximum lignin of 68 ± 4 mg g(-1) from the rice straw biomass, and subsequent enzymatic hydrolysis of the residual holocellulose enriched biomass showed maximum reducing sugars of 333 ± 11 mg g(-1) with a saccharification efficiency of 36.0 ± 3.2 % in 24 h at 10 % solids loading.

Oxidative degradation of biorefinery lignin obtained after pretreatment of forest residues of Douglas Fir.

PubMed

Srinivas, Keerthi; de Carvalho Oliveira, Fernanda; Teller, Philip Johan; Gonҫalves, Adilson Roberto; Helms, Gregory L; Ahring, Birgitte Kaer

2016-12-01

Harvested forest residues are usually considered a fire hazards and used as "hog-fuel" which results in air pollution. In this study, the biorefinery lignin stream obtained after wet explosion pretreatment and enzymatic hydrolysis of forestry residues of Douglas Fir (FS-10) was characterized and further wet oxidized under alkaline conditions. The studies indicated that at 10% solids, 11.7wt% alkali and 15min residence time, maximum yields were obtained for glucose (12.9wt%), vanillin (0.4wt%) at 230°C; formic acid (11.6wt%) at 250°C; acetic acid (10.7wt%), hydroxybenzaldehyde (0.2wt%), syringaldehyde (0.13wt%) at 280°C; and lactic acid (12.4wt%) at 300°C. FTIR analysis of the solid residue after wet oxidation showed that the aromatic skeletal vibrations relating to lignin compounds increased with temperature indicating that higher severity could result in increased lignin oxidation products. The results obtained, as part of the study, is significant for understanding and optimizing processes for producing high-value bioproducts from forestry residues. Copyright © 2016 Elsevier Ltd. All rights reserved.

Metabolic fate and distribution of [{sup 14}C]1,3-dichloropropene in carrot, lettuce, radish, tomato, and wheat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnkow, D.E.; Byrne, S.L.; Huskin, M.A.

1996-10-01

This study examined the nature of the radioactive residue in carrot, lettuce, radish, tomato, and wheat grown in soil treated with uniformly {sup 14}C-labeled cis- and trans-1,3-dichloropropene (1,3-D). Each crop was grown in soil treated at or above the maximum use rate. Carrot root and top, lettuce, radish root and top, tomato fruit and vine, and wheat forage, straw and grain were harvested, processed, and analyzed. The {sup 14}C residues were subjected to sequential extraction with diethyl ether and aqueous acetonitrile. The residues that remained were subjected to extraction, fractionation, and hydrolysis with buffer, enzymes, acid, alkali, and strong oxidizingmore » agents. Analyses of the solubilized residues demonstrated that no detectable parent, 1,3-D, or the putative metabolites 3-chloroallyl alcohol and 3-chloroacrylic acid were present. The components of the extractable residue included most major plant constituents (i.e., protein, pigments, organic acids, sucrose, cellulose, and lignin). Thus, natural incorporation of the {sup 14}C-label into natural plant biochemicals is demonstrated.« less

Determination of benazolin-ethyl residues in soil and rape seed by SPE clean-up and GC with electron capture detection.

PubMed

Liu, Xiaolu; Yang, Tao; Hu, Jiye

2013-01-01

A method has been developed and established for residue determination of benazolin-ethyl in soil and rape seed samples by gas chromatography with electron capture detection (GC-ECD). Limits of quantification of the method are 0.005 mg/kg for both soil and rape seed, which are sufficiently below the maximum residue limit, and the limit of detection is 0.0023 ng. The average recoveries of the analyte range from 85.89 to 105.84% with relative standard deviations (coefficient of variation) less than 5.53% at the three spike levels (0.005, 0.1 and 0.5 mg/kg). The half-life of benazolin-ethyl in soil from the experimental field is 4.62 days. The final residues of benazolin-ethyl in soil and rape seed samples are lower than 0.005 mg/kg at harvest time. Direct confirmation of the analyte in real samples is achieved by GC-mass spectrometry. It is demonstrated that the proposed method is simple, rapid and efficient, and reliable to detect benazolin-ethyl residues in soil and rape seed samples.

Survey of pesticide residues in maize, cowpea and millet from northern Cameroon: part I.

PubMed

Sonchieu, Jean; Benoit Ngassoum, Martin; Bosco Tchatchueng, Jean; Srivastava, Ashutosh Kumar; Srivastava, Laxman Prasad

2010-01-01

In northern Cameroon, the misuse of pesticides for pest control is common among small-scale farmers. Therefore, monitoring of pesticide residues was carried out on stored maize, cowpea and millet from eight localities. The determination of residues of organochlorines (lindane, α-endosulfan and β-endosulfan), organophosphorus compounds (malathion and pirimiphos-methyl), synthetic pyrethroids (permethrin) and carbamates (carbufuran) was performed using GC-ECD/NPD and GC-MS for confirmation. Organochlorine pesticides were detected more frequently and in higher concentrations, ranging from 0.02 ± 0.01 mg kg(-1) for β-endosulfan in millet to 9.53 ± 4.00 mg kg(-1) lindane in maize, than organophosphorus compounds, with concentrations varying from 0.04 ± 0.03 mg kg(-1) for pirimiphos methyl to 0.23 ± 0.38 mg kg(-1) for malathion in maize. Permethrin was found only in maize at 0.39 ± 0.23 mg kg(-1). No carbofuran was found. More than 75% of samples contained pesticide residues above the maximum residue limit (MRL); showing a potential human dietary risk related to consumption of these grains.

78 FR 57285 - 2,5-Furandione, Polymer With Ethenylbenzene, Hydrolyzed, 3-(Dimethylamino)propyl Imide, Imide...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-18

..., Polymer With Ethenylbenzene, Hydrolyzed, 3- (Dimethylamino)propyl Imide, Imide With Polyethylene..., polymer with ethenylbenzene, hydrolyzed, 3-(dimethylamino)propyl imide, imide with polyethylene... to establish a maximum permissible level for residues of 2,5-furandione, polymer with ethenylbenzene...

Improving hot region prediction by parameter optimization of density clustering in PPI.

PubMed

Hu, Jing; Zhang, Xiaolong

2016-11-01

This paper proposed an optimized algorithm which combines density clustering of parameter selection with feature-based classification for hot region prediction. First, all the residues are classified by SVM to remove non-hot spot residues, then density clustering of parameter selection is used to find hot regions. In the density clustering, this paper studies how to select input parameters. There are two parameters radius and density in density-based incremental clustering. We firstly fix density and enumerate radius to find a pair of parameters which leads to maximum number of clusters, and then we fix radius and enumerate density to find another pair of parameters which leads to maximum number of clusters. Experiment results show that the proposed method using both two pairs of parameters provides better prediction performance than the other method, and compare these two predictive results, the result by fixing radius and enumerating density have slightly higher prediction accuracy than that by fixing density and enumerating radius. Copyright © 2016. Published by Elsevier Inc.

Experimental and analytical study of high velocity impact on Kevlar/Epoxy composite plates

NASA Astrophysics Data System (ADS)

Sikarwar, Rahul S.; Velmurugan, Raman; Madhu, Velmuri

2012-12-01

In the present study, impact behavior of Kevlar/Epoxy composite plates has been carried out experimentally by considering different thicknesses and lay-up sequences and compared with analytical results. The effect of thickness, lay-up sequence on energy absorbing capacity has been studied for high velocity impact. Four lay-up sequences and four thickness values have been considered. Initial velocities and residual velocities are measured experimentally to calculate the energy absorbing capacity of laminates. Residual velocity of projectile and energy absorbed by laminates are calculated analytically. The results obtained from analytical study are found to be in good agreement with experimental results. It is observed from the study that 0/90 lay-up sequence is most effective for impact resistance. Delamination area is maximum on the back side of the plate for all thickness values and lay-up sequences. The delamination area on the back is maximum for 0/90/45/-45 laminates compared to other lay-up sequences.

The relative contribution of waves, tides, and nontidal residuals to extreme total water levels on U.S. West Coast sandy beaches

USGS Publications Warehouse

Serafin, Katherine A.; Ruggiero, Peter; Stockdon, Hilary F.

2017-01-01

To better understand how individual processes combine to cause flooding and erosion events, we investigate the relative contribution of tides, waves, and nontidal residuals to extreme total water levels (TWLs) at the shoreline of U.S. West Coast sandy beaches. Extreme TWLs, defined as the observed annual maximum event and the simulated 100 year return level event, peak in Washington, and are on average larger in Washington and Oregon than in California. The relative contribution of wave-induced and still water levels (SWL) to the 100 year TWL event is similar to that of the annual maximum event; however, the contribution of storm surge to the SWL doubles across events. Understanding the regional variability of TWLs will lead to a better understanding of how sea level rise, changes in storminess, and possible changes in the frequency of major El Niños may impact future coastal flooding and erosion along the U.S. West Coast and elsewhere.

Gravity survey of Dixie Valley, west-central Nevada

USGS Publications Warehouse

Schaefer, Donald H.

1983-01-01

Dixie Valley, a northeast-trending structural trough typical of valleys in the Basin and Range Province, is filled with a maximum of about 10,000 feet of alluvial and lacustrine deposits , as estimated from residual-gravity measurements obtained in this study. On the basis of gravity measurements at 300 stations on nine east-west profiles, the gravity residuals reach a maximum of 30 milligals near the south-central part of the valley. Results from a three-dimensional inversion model indicate that the central depression of the valley is offset to the west of the geographic axis. This offset is probably due to major faulting along the west side of the valley adjacent to the Stillwater Range. Comparison of depths to bedrock obtained during this study and depths obtained from a previous seismic-refraction study indicates a reasonably good correlation. A heterogeneous distribution of densities within the valley-fill deposits would account for differing depths determined by the two methods. (USGS)

Improved volatile fatty acid and biomethane production from lipid removed microalgal residue (LRμAR) through pretreatment.

PubMed

Suresh, Arumuganainar; Seo, Charles; Chang, Ho Nam; Kim, Yeu-Chun

2013-12-01

Renewable energy from lipid removed microalgal residues (LRμARs) serves as a promising tool for sustainable development of the microalgal biodiesel industry. Hence, in this study, LRμAR from Ettlia sp. was characterized for its physico-biochemical parameters, and applied to various pretreatment to increase the biodegradability and used in batch experiments for the production of volatile fatty acids (VFA) and biomethane. After various pretreatments, the soluble organic matters were increased at a maximum of 82% in total organic matters in alkali-autoclaved sample. In addition, VFA and methane production was enhanced by 30% and 40% in alkali-sonicated and alkali-autoclaved samples, respectively. Methane heating value was recovered at maximum of 6.6 MJ kg(-1)VS in alkali-autoclaved conditions with comparison to non-pretreated samples. The pretreatment remarkably improved LRμAR solubilization and enhanced VFA and biomethane production, which holds immense potential to eventually reduce the cost of algal biodiesel. Copyright © 2013 Elsevier Ltd. All rights reserved.

Enhanced production of xylanase from locally isolated fungal strain using agro-industrial residues under solid-state fermentation.

PubMed

Abdullah, Roheena; Nisar, Kinza; Aslam, Aafia; Iqtedar, Mehwish; Naz, Shagufta

2015-01-01

This study is related to the isolation of fungal strain for xylanase production using agro-industrial residues. Forty fungal strains with xylanolytic potential were isolated by using xylan agar plates and quantitatively screened in solid-state fermentation. Of all the tested isolates, the strain showing highest ability to produce xylanase was assigned the code Aspergillus niger LCBT-14. For the enhanced production of the enzyme, five different fermentation media were evaluated. Out of all media, M4 containing wheat bran gave maximum enzyme production. Effect of different variables including incubation time, temperature, pH, carbon and nitrogen sources has been investigated. The optimum enzyme production was obtained after 72 h at 30°C and pH 4. Glucose as a carbon source while ammonium sulphate and yeast extract as nitrogen sources gave maximum xylanase production (946 U/mL/min). This study was successful in producing xylanase by A. niger LCBT-14 economically by utilising cheap indigenous substrate.

Spectral shapes of rovibrational lines of CO broadened by He, Ar, Kr and SF6: A test case of the Hartmann-Tran profile

NASA Astrophysics Data System (ADS)

Ngo, N. H.; Lin, H.; Hodges, J. T.; Tran, H.

2017-12-01

High signal-to-noise ratio spectra of the (3-0) band P(1) and P(17) lines of CO broadened by He, Ar, Kr and SF6 were measured with a frequency-stabilized cavity ring-down spectroscopy system. For each collision-partner and both lines, multiple spectra were measured over pressures spanning nearly three decades up to 130 kPa. These data were analyzed with a multispectrum fitting procedure. Line shapes were modeled using the Hartmann-Tran (HT) profile with first-order line mixing as well as several other simplified profiles. The results show that for all considered collision partners (with the exception of SF6), the HT profile captures the measured line shapes with maximum absolute residuals that are within 0.1% of the peak absorption. In the case of SF6, which is the heaviest perturber investigated here, the maximum residuals for the HT profile are twice as large as for the other collision partners.

Pediatric Diaphyseal Femur Fractures: Submuscular Plating Compared With Intramedullary Nailing.

PubMed

Sutphen, Sean A; Mendoza, Juan D; Mundy, Andrew C; Yang, Jingzhen G; Beebe, Allan C; Samora, Walter P; Klingele, Kevin E

2016-11-01

This study compared the radiographic and clinical outcomes of pediatric diaphyseal femur fractures treated by submuscular plating, flexible retrograde intramedullary nailing, or rigid antegrade intramedullary nailing with a trochanteric entry point in skeletally immature patients who were 8 years and older. A retrospective review was conducted of skeletally immature patients 8 years and older who were treated for femur fracture with submuscular plating, flexible intramedullary nailing, or rigid intramedullary nailing from 2001 to 2014 with a minimum 12-week follow-up. Treatment outcomes were compared for statistical significance, including time to union, malunion, nonunion, heterotopic ossification, avascular necrosis, time to full weight bearing, limb length discrepancy, residual limp, painful hardware, and infection. The study identified 198 femur fractures in 196 patients (mean age, 11.9 years). Each femur fracture was treated with submuscular plating (35), flexible intramedullary nailing (61), or rigid intramedullary nailing (102). Mean follow-up across the cohort was 48 weeks, ranging from 12 to 225 weeks. Flexible nailing was associated with an increased incidence of malunion (P<.0001) and hardware irritation (P=.0204) and longer time to full weight bearing (P=.0018). Rigid nailing was associated with an increased incidence of limp at 12-week followup (P=.0412). Additionally, 23.5% of patients who were treated with rigid nailing had heterotopic ossification. Of all surgical methods, submuscular plating allowed for the most rapid return to full weight bearing (mean, 7 weeks) and offered the fastest healing rate (mean, 6 weeks). Submuscular plating resulted in faster times to union and full weight bearing, with minimal complication rates. Rigid intramedullary nailing with trochanteric entry resulted in a lower incidence of malunion and hardware-related complications; however, these patients had an increased incidence of heterotopic ossification and residual limp postoperatively. Flexible retrograde intramedullary nailing resulted in the highest rates of malunion and hardware irritation and the longest time to full weight bearing. [Orthopedics. 2016; 39(6):353-358.]. Copyright 2016, SLACK Incorporated.

Origin and fate of sulfide liquids in hotspot volcanism (La Réunion): Pb isotope constraints from residual Fe-Cu oxides

NASA Astrophysics Data System (ADS)

Vlastélic, I.; Gannoun, A.; Di Muro, A.; Gurioli, L.; Bachèlery, P.; Henot, J. M.

2016-12-01

Immiscible sulfide liquids in basaltic magmas play an important role in trace metal transport and the sulfur budget of volcanic eruptions. However, sulfides are transient phases, whose origin and fate are poorly constrained. We address these issues by analyzing sulfide destabilization products preserved in lavas from La Réunion Island. Iron oxide globules and coatings, typically 20-80 μm in size, were found to occur in vesicles of differentiated lavas from Piton des Neiges, and recent pumice samples from Piton de la Fournaise. Field and mineralogical evidence indicates that the iron oxides are syn-eruptive phases not resulting from hydrothermal processes. Samples were first studied by Scanning Electron Microscopy. The globules were separated, whereas the smaller spherules and coatings were concentrated by magnetic sorting and acid leaching, and samples were processed through wet chemistry. The Fe oxide phases comprise 49-74 wt.% Fe, 26-40 wt.% O, and up to 6 wt.% Cu, 811 ppm Ni, 140 ppm Bi, and 8.5 ppm Pb. Compared to the host lava, Cu, Ni, and Bi are enriched by a factor of 101-103. Systematic Pb isotope disequilibrium (between 500 ppm and 2.9% for 206Pb/204Pb) exists between Fe oxides and host rocks, with Fe oxides generally displaying less radiogenic ratios. Unradiogenic Pb is a typical signature of sulfide, which tends to concentrate Pb, but not its parent elements U and Th. Thus, both the chemical and isotopic compositions of the vesicle-hosted Fe oxides suggest that they are more or less direct products of the destabilization of immiscible sulfide liquids. Although Pb dominantly partitions into the gas phase during sulfide breakdown, the original Pb isotope signature of sulfide is preserved in the residual oxide. The composition estimated for the parent sulfides (206Pb/204Pb = 18.20-18.77, 207Pb/204Pb = 15.575, and 208Pb/204Pb = 38.2-38.8) precludes a genetic link with the La Réunion plume, and suggests a lithospheric or crustal origin. It is estimated that magma ascent velocities at Piton de la Fournaise are high enough to counterbalance the settling velocities of millimeter-size sulfides. Despite their high density, sulfide liquids are thus transferred upward during eruptions and their destabilization contributes to SO2 emanations. Assimilation of foreign sulfides from the lithosphere can explain why SO2 emissions sometimes (e.g., during the April 2007 eruption) exceed those predicted from the S content of melt inclusions.

Effect of tempering treatment upon the residual stress of bimetallic roll

NASA Astrophysics Data System (ADS)

Sano, Y.; Noda, N.-A.; Takase, Y.; Torigoe, R.; Tsuboi, K.; Aridi, M. R.; Sanada, Y.; Lan, L. Y.

2018-06-01

Bimetallic rolls are widely used in steel rolling industries because of the excellent hardness, wear resistance, and high temperature properties. However, thermal stress is produced by heating-cooling thermal cycles, which is a great challenge for their practical application. Indeed, if severe thermal tensile stress is introduced into these rolls, it can assist the thermal cracks to propagate, even lead to the overall failure of rolls. In this paper, we investigated the effect of tempering treatment on the residual stress after the bimetallic rolls were subjected to quenching. Compared with the non-uniform heating-quenching process, the tempering process makes the maximum stress at the core decreased by 15% (from 275 MPa to 234 MPa) with considering martensite transformation but decreased by 26% (from 275 MPa to 201 MPa) without considering martensite transformation. For tempering process after uniform heating quenching, the maximum stress at the core decreases by 24% from 357 MPa to 273 MPa with considering martensite transformation but decreases by 30% from 357 MPa to 246 MPa without considering martensite transformation. And compared with the non-uniform heating-quenching process, the double tempering process makes the maximum stress at the core decreased by 8% (from 275 MPa to 253 MPa) with considering martensite transformation but decreased by 27% (from 275 MPa to 200 MPa) without considering martensite transformation.

Supernova Ia Spectra and Spectrophotometric Time Series: Recognizing Twins and the Consequences for Cosmological Distance Measurements

NASA Astrophysics Data System (ADS)

Fakhouri, Hannah Kathleen

In Part I we introduce the method and results of the Twin Supernova analysis. This novel approach to Type Ia supernova standardization is currently only possible with spectrophotometric timeseries observations from the Nearby Supernova Factory. As Chapters 1 through 4 will explore, we select an ideal subset of supernovae, find pairs whose features match well in flux at all wavelengths and times, and test their dispersion in brightness. The analysis is completed in a blinded fashion, ensuring that we are not tuning our results. What we find is that twin supernovae do indeed have a small brightness dispersion. Part II shows two additional analyses related to the standardization of Type Ia supernovae. In Chapter 5 we present a check on the results of Bailey et al. [2009]. Literature supernovae with spectra near maximum light were tested to see how well their magnitudes could be standardized using the flux ratio method of Bailey et al [2009]. Chapter 6 shows a study with data from the Nearby Supernova Factory. Using only the spectrophotometric observations near maximum light, we calculate monochromatic Hubble Diagram residuals for each supernova. Those residuals are then corrected using a flux ratio, similar to Bailey et al. [2009] to test the standardization possibilities using only near-maximum observations.

Multiresidue determination of fluoroquinolone, sulfonamide, trimethoprim, and chloramphenicol antibiotics in urban waters in China.

PubMed

Peng, Xianzhi; Tan, Jianhua; Tang, Caiming; Yu, Yiyi; Wang, Zhendi

2008-01-01

A feasible method has been optimized to simultaneously determine multiclass antibiotic residues, including sulfonamides, fluoroquinolones, trimethoprim, and chloramphenicol in urban riverine water and wastewater by off-line solid phase extraction and high-performance liquid chromatography coupled with a diode-array ultraviolet detector and a fluorescence detector. Internal standard and standard addition methods were used in combination to identify and quantify these antibiotics to compensate for the matrix interference. The method quantification limits (MQLs) were determined to be 0.035 to 0.100 microg/L and 0.100 to 0.300 microg/L for the riverine water and wastewater, respectively. Recoveries of the investigated antibiotics ranged from 63 to 126%. Sulfamethoxazole was the most frequently detected antibiotic residue in Guangzhou section of the Major Pearl River, South China, with a maximum level of 0.510 microg/L. Fluoroquinolone antibiotics were relatively less detected with a maximum level of 0.459 microg/L. The maximum concentration of sulfamethoxazole reached 5.597 microg/L in the raw wastewater from a large-scale sewage treatment plant in Guangzhou city. Around 30% of sulfamethoxazole might survive the primary clarification and biotreatment processes in the sewage treatment plant. None of the investigated antibiotics have been found above MQLs in the final effluent after chlorine disinfection.

Effects of alteplase for acute stroke according to criteria defining the European Union and United States marketing authorizations: Individual-patient-data meta-analysis of randomized trials.

PubMed

Hacke, Werner; Lyden, Patrick; Emberson, Jonathan; Baigent, Colin; Blackwell, Lisa; Albers, Gregory; Bluhmki, Erich; Brott, Thomas; Cohen, Geoffrey; Davis, Stephen M; Donnan, Geoffrey A; Grotta, James C; Howard, George; Kaste, Markku; Koga, Masatoshi; von Kummer, Rüdiger; Lansberg, Maarten G; Lindley, Richard I; Olivot, Jean-Marc; Parsons, Mark; Sandercock, Peter Ag; Toni, Danilo; Toyoda, Kazunori; Wahlgren, Nils; Wardlaw, Joanna M; Whiteley, William N; Del Zoppo, Gregory; Lees, Kennedy R

2018-02-01

Background The recommended maximum age and time window for intravenous alteplase treatment of acute ischemic stroke differs between the Europe Union and United States. Aims We compared the effects of alteplase in cohorts defined by the current Europe Union or United States marketing approval labels, and by hypothetical revisions of the labels that would remove the Europe Union upper age limit or extend the United States treatment time window to 4.5 h. Methods We assessed outcomes in an individual-patient-data meta-analysis of eight randomized trials of intravenous alteplase (0.9 mg/kg) versus control for acute ischemic stroke. Outcomes included: excellent outcome (modified Rankin score 0-1) at 3-6 months, the distribution of modified Rankin score, symptomatic intracerebral hemorrhage, and 90-day mortality. Results Alteplase increased the odds of modified Rankin score 0-1 among 2449/6136 (40%) patients who met the current European Union label and 3491 (57%) patients who met the age-revised label (odds ratio 1.42, 95% CI 1.21-1.68 and 1.43, 1.23-1.65, respectively), but not in those outside the age-revised label (1.06, 0.90-1.26). By 90 days, there was no increased mortality in the current and age-revised cohorts (hazard ratios 0.98, 95% CI 0.76-1.25 and 1.01, 0.86-1.19, respectively) but mortality remained higher outside the age-revised label (1.19, 0.99-1.42). Similarly, alteplase increased the odds of modified Rankin score 0-1 among 1174/6136 (19%) patients who met the current US approval and 3326 (54%) who met a 4.5-h revised approval (odds ratio 1.55, 1.19-2.01 and 1.37, 1.17-1.59, respectively), but not for those outside the 4.5-h revised approval (1.14, 0.97-1.34). By 90 days, no increased mortality remained for the current and 4.5-h revised label cohorts (hazard ratios 0.99, 0.77-1.26 and 1.02, 0.87-1.20, respectively) but mortality remained higher outside the 4.5-h revised approval (1.17, 0.98-1.41). Conclusions An age-revised European Union label or 4.5-h-revised United States label would each increase the number of patients deriving net benefit from alteplase by 90 days after acute ischemic stroke, without excess mortality.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verstraete, Frans, E-mail: Frans.Verstraete@ec.europa.eu

Directive 2002/32/EC of 7 May 2002 of the European Parliament and of the Council on undesirable substances in animal feed is the framework for the EU action on undesirable substances in feed. This framework Directive provides: ⁎that products intended for animal feed may enter for use in the Union from third countries, be put into circulation and/or used in the Union only if they are sound, genuine and of merchantable quality and therefore when correctly used do not represent any danger to human health, animal health or to the environment or could adversely affect livestock production. ⁎that in order tomore » protect animal and public health and the environment, maximum levels for specific undesirable substances shall be established where necessary. ⁎for mandatory consultation of a scientific body (EFSA) for all provisions which may have an effect upon public health or animal health or on the environment. ⁎that products intended for animal feed containing levels of an undesirable substance that exceed the established maximum level may not be mixed for dilution purposes with the same, or other, products intended for animal feed and may not be used for the production of compound feed. Based on the provisions and principles laid down in this framework Directive, maximum levels for a whole range of undesirable substances have been established at EU level. During the discussions in view of the adoption of Directive 2002/32/EC, the European Commission made the commitment to review all existing provisions on undesirable substances on the basis of updated scientific risk assessments. Following requests of the European Commission, the Panel on Contaminants in the Food Chain (CONTAM) from the European Food Safety Authority (EFSA) has completed a series of 30 risk assessments undertaken over the last 5 years on undesirable substances in animal feed reviewing the possible risks for animal and human health due to the presence of these substances in animal feed. EU legislation on undesirable substances has undergone recently several changes to take account of these most recent scientific opinions. Furthermore EFSA has assessed the risks for public and animal health following the unavoidable carry-over of coccidiostats into non target feed. Maximum levels for the unavoidable carry-over have been established for the non-target feed and the food of animal origin from non-target animal species.« less

Sheet intrusions and deformation of Piton des Neiges, and their implication for the volcano-tectonics of La Réunion

NASA Astrophysics Data System (ADS)

Chaput, Marie; Famin, Vincent; Michon, Laurent

2017-10-01

To understand the volcano-tectonic history of Piton des Neiges (the dormant volcano of La Réunion), we measured in the field the orientation of sheeted intrusions and deformation structures, and interpreted the two datasets separately with a paleostress inversion. Results show that the multiple proposed rift zones may be simplified into three trends: (1) a N30°E, 5 km wide linear rift zone running to the south of the edifice, active in the shield building (≥ 2.48-0.43 Ma) and terminal stages (190-22 ka); (2) a curved N110 to N160°E rift zone, widening from 5 km to 10 km toward the NW flank, essentially active during the early emerged shield building (≥ 1.3 Ma); and (3) two sill zones, ≤ 1 km thick in total, in the most internal parts of the volcano, active in the shield building and terminal stages. In parallel, deformation structures reveal that the tectonics of the edifice consisted in three end-member stress regimes sharing common stress axes: (1) NW-SE extension affecting in priority the south of the edifice near the N30°E rift zone; (2) NNE-SSW extension on the northern half of the volcano near the N110-160°E rift zone; (3) compression occurring near the sill zones, with a NE-SW or NW-SE maximum principal stress. These three stress regimes are spatially correlated and mechanically compatible with the injection trends. Combined together, our data show that the emerged Piton des Neiges underwent sector spreading delimited by perpendicular rift zones, as observed on Piton de la Fournaise (the active volcano of La Réunion). Analogue experiments attribute such sector spreading to brittle edifices built on a weaker substratum. We therefore conclude that La Réunion volcanoes are both brittle, as opposed to Hawaiian volcanoes or Mount Etna whose radial spreading is usually attributed to a ductile body within the edifices.

Determination of endogenous concentrations of nitrites and nitrates in different types of cheese in the United States: method development and validation using ion chromatography.

PubMed

Genualdi, Susan; Jeong, Nahyun; DeJager, Lowri

2018-04-01

Nitrites and nitrates can be present in dairy products from both endogenous and exogenous sources. In the European Union (EU), 150 mg kg - 1 of nitrates are allowed to be added to the cheese milk during the manufacturing process. The CODEX General Standard for Food Additives has a maximum permitted level of 50 mg kg - 1 residue in cheese, while in the United States (U.S.) nitrates are unapproved for use as food additives in cheese. In order to be able to investigate imported cheeses for nitrates intentionally added as preservatives and the endogenous concentrations of nitrates and nitrites present in cheeses in the U.S. marketplace, a method was developed and validated using ion chromatography with conductivity detection. A market sampling of cheese samples purchased in the Washington DC metro area was performed. In 64 samples of cheese, concentrations ranged from below the method detection limit (MDL) to 26 mg kg - 1 for nitrates and no concentrations of nitrites were found in any of the cheese samples above the MDL of 0.1 mg kg - 1 . A majority of the samples (93%) had concentrations below 10 mg kg - 1 , which indicate the presence of endogenous nitrates. The samples with concentrations above 10 mg kg - 1 were mainly processed cheese spread, which can contain additional ingredients often of plant-based origin. These ingredients are likely the cause of the elevated nitrate concentrations. The analysis of 12 additional cheese samples that are liable to the intentional addition of nitrates, 9 of which were imported, indicated that in this limited study, concentrations of nitrate in the U.S.-produced cheeses did not differ from those in imported samples.

Advancing the 3Rs in regulatory toxicology - Carcinogenicity testing: Scope for harmonisation and advancing the 3Rs in regulated sectors of the European Union.

PubMed

Annys, Erwin; Billington, Richard; Clayton, Rick; Bremm, Klaus-Dieter; Graziano, Michael; McKelvie, Jo; Ragan, Ian; Schwarz, Michael; van der Laan, Jan Willem; Wood, Charles; Öberg, Mattias; Wester, Piet; Woodward, Kevin N

2014-07-01

Different government agencies operating in the European Union regulate different types of chemical products but all require testing for carcinogenicity to support applications for product marketing and commercialisation. A conference was held in Brussels in 2013 where representatives of the pharmaceutical, animal health, chemical and plant protection industries, together with representatives of regulatory agencies, universities and other stakeholders, met under the auspices of The European Partnership for Alternative Approaches to Animal Testing (EPAA) to discuss the varying requirements for carcinogenicity testing, and how these studies might be refined to improve hazard evaluation and risk assessment while implementing principles of the 3Rs (replacement, refinement and reduction in animal studies). While there are some similarities, the regulatory approaches in pharmaceutical, animal health, chemical and plant protection sectors have varying degrees of flexibility in requirements for carcinogenicity testing, to an extent reflecting concerns over the magnitude and duration of human exposure, either directly as in therapeutic exposure to pharmaceuticals, or indirectly through the ingestion of residues of veterinary drugs or plant protection chemicals. The article discusses these differences and other considerations for modified carcinogenicity testing paradigms on the basis of scientific and 3Rs approaches. Copyright © 2014 Elsevier Inc. All rights reserved.

Pesticide mitigation strategies for surface water quality

USDA-ARS?s Scientific Manuscript database

Pesticide residues are being increasingly detected in surface water in agricultural and urban areas. In some cases water bodies are being listed under the Clean Water Act 303(d) as impaired and Total Maximum Daily Loads are required to address the impairments in agricultural areas. Pesticides in sur...

How applicable is uneven-age management in northern forest types?

Treesearch

Stanley M. Filip

1977-01-01

For the proper application and practice of uneven-age management, one must consider residual stocking, maximum tree-size objective, and diameter distribution. All three components are described, and it is shown how they fit into a practical package for application in a timber tract.

77 FR 48899 - Flutriafol; Pesticide Tolerances for Emergency Exemptions

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-15

... cotton, undelinted seed; cotton, meal; cotton, refined oil; and cotton gin byproducts. This action is in..., and Rodenticide Act (FIFRA) authorizing use of the pesticide on cotton. This regulation establishes a maximum permissible level for residues of flutriafol in or on cotton commodities. The time-limited...

Saturation pulse design for quantitative myocardial T1 mapping.

PubMed

Chow, Kelvin; Kellman, Peter; Spottiswoode, Bruce S; Nielles-Vallespin, Sonia; Arai, Andrew E; Salerno, Michael; Thompson, Richard B

2015-10-01

Quantitative saturation-recovery based T1 mapping sequences are less sensitive to systematic errors than the Modified Look-Locker Inversion recovery (MOLLI) technique but require high performance saturation pulses. We propose to optimize adiabatic and pulse train saturation pulses for quantitative T1 mapping to have <1 % absolute residual longitudinal magnetization (|MZ/M0|) over ranges of B0 and [Formula: see text] (B1 scale factor) inhomogeneity found at 1.5 T and 3 T. Design parameters for an adiabatic BIR4-90 pulse were optimized for improved performance within 1.5 T B0 (±120 Hz) and [Formula: see text] (0.7-1.0) ranges. Flip angles in hard pulse trains of 3-6 pulses were optimized for 1.5 T and 3 T, with consideration of T1 values, field inhomogeneities (B0 = ±240 Hz and [Formula: see text]=0.4-1.2 at 3 T), and maximum achievable B1 field strength. Residual MZ/M0 was simulated and measured experimentally for current standard and optimized saturation pulses in phantoms and in-vivo human studies. T1 maps were acquired at 3 T in human subjects and a swine using a SAturation recovery single-SHot Acquisition (SASHA) technique with a standard 90°-90°-90° and an optimized 6-pulse train. Measured residual MZ/M0 in phantoms had excellent agreement with simulations over a wide range of B0 and [Formula: see text]. The optimized BIR4-90 reduced the maximum residual |MZ/M0| to <1 %, a 5.8× reduction compared to a reference BIR4-90. An optimized 3-pulse train achieved a maximum residual |MZ/M0| <1 % for the 1.5 T optimization range compared to 11.3 % for a standard 90°-90°-90° pulse train, while a 6-pulse train met this target for the wider 3 T ranges of B0 and [Formula: see text]. The 6-pulse train demonstrated more uniform saturation across both the myocardium and entire field of view than other saturation pulses in human studies. T1 maps were more spatially homogeneous with 6-pulse train SASHA than the reference 90°-90°-90° SASHA in both human and animal studies. Adiabatic and pulse train saturation pulses optimized for different constraints found at 1.5 T and 3 T achieved <1 % residual |MZ/M0| in phantom experiments, enabling greater accuracy in quantitative saturation recovery T1 imaging.

Evolution of residual stresses in micro-arc oxidation ceramic coatings on 6061 Al alloy

NASA Astrophysics Data System (ADS)

Shen, Dejiu; Cai, Jingrui; Guo, Changhong; Liu, Peiyu

2013-11-01

Most researches on micro-arc oxidation mainly focus on the application rather than discovering the evolution of residual stresses. However, residual stresses in the surface coatings of structural components have adverse effects on their properties, such as fatigue life, dimensional stability and corrosion resistance, etc. The micro-arc oxidation ceramic coatings are produced on the surfaces of 6061 aluminum alloy by a homemade asymmetric AC type of micro-arc oxidation equipment of 20 kW. A constant current density of 4.4±0.1 A/dm2 and a self-regulated composite electrolyte are used. The micro-arc oxidation treatment period ranges from 10 min to 40 min, and the thickness of the ceramic coatings is more than 20 μm. Residual stresses attributed to γ-Al2O3 constituent in the coatings at different micro-arc oxidation periods are analyzed by an X-ray diffractometer using the sin2 ψ method. The analysis results show that the residual stress in the ceramic coatings is compressive in nature, and it increases first and then decreases with micro-arc oxidation time increase. The maximum stress value is 1 667±20 MPa for period of 20 min. Through analyzing the coating thickness, surface morphology and phase composition, it is found that the residual stress in the ceramic coatings is linked closely with the coating growth, the phase composition and the micro cracks formed. It is also found that both the heat treatment and the ultrasonic action release remarkably the residual compressive stress. The heat treatment makes the residual compressive stress value decrease 1 378 MPa. The ultrasonic action even alters the nature of the residual stress, making the residual compressive stress change into a residual tensile stress.

Strategies to reduce exposure of fumonisins from complementary foods in rural Tanzania.

PubMed

Kimanya, Martin E; De Meulenaer, Bruno; Van Camp, John; Baert, Katleen; Kolsteren, Patrick

2012-10-01

Feeding infants with maize can expose them to fumonisin mycotoxins. We assessed fumonisin exposure from complementary foods in rural Tanzania and determined strategies to reduce the exposure. We conducted a cross-sectional study in four villages of Tarakea division, Northern Tanzania. We used a repeat 24-hour dietary recall to collect data of maize consumption as complementary food for 254 infants aged 6-8 months. Fumonisin concentrations in the maize were also estimated. Fumonisin exposure was assessed using @risk analysis software. With the software, several maximum fumonisin contamination and maize consumption patterns were combined in order to determine effective strategies for minimizing fumonisin exposure. Of the infants, 89% consumed maize at amounts up to 158g/person/day (mean; 43g/person/day±28). The maize was contaminated with fumonisins at levels up to 3201µgkg(-1) . Risk of fumonisin intake above the provisional maximum tolerable daily limit of 2µgkg(-1) body weight was 15% (95% confidence interval; 10-19). The risk was minimized when the maximum contamination was set at 150µgkg(-1) . The risk was also minimized when the maximum consumption was set at 20g/child/day while keeping the maximum contamination at the European Union (EU) maximum tolerated limit (MTL) of 1000µgkg(-1) . Considering the economical and technological limitations of adopting good agricultural practices in rural Tanzania, it is practically difficult to reduce contamination in maize to 150µgkg(-1) . We suggest adoption of the EU MTL of 1000µgkg(-1) for fumonisins in maize and reduction, by replacement with another cereal, of the maize component in complementary foods to a maximum intake of 20g/child/day. © 2011 Blackwell Publishing Ltd.

Agro-industrial residue from starch extraction of Pachyrhizus ahipa as filler of thermoplastic corn starch films.

PubMed

López, O V; Versino, F; Villar, M A; García, M A

2015-12-10

Biocomposites films based on thermoplastic corn starch (TPS) containing 0.5% w/w fibrous residue from Pachyrhizus ahipa starch extraction (PASR) were obtained by melt-mixing and compression molding. PASR is mainly constituted by remaining cell walls and natural fibers, revealed by Scanning Electron Microscopy (SEM). Chemical composition of the residue indicated that fiber and starch were the principal components. Biocomposites thermo-stability was determined by Thermo-Gravimetric Analysis. A continuous PASR-TPS interface was observed by SEM, as a result of a good adhesion of the fibrous residue to starch matrix. Likewise, films containing PASR presented fewer superficial cracks than TPS ones, whereas their fracture surfaces were more irregular. Besides, the presence of PASR increased starch films roughness, due to fibers agglomerates. Films reinforced with PASR showed significantly lower water vapor permeability (WVP). In addition, PARS filler increased maximum tensile strength and Young's modulus of TPS films, thus leading to more resistant starch matrixes. Copyright © 2015 Elsevier Ltd. All rights reserved.

An Adaptive Kalman Filter using a Simple Residual Tuning Method

NASA Technical Reports Server (NTRS)

Harman, Richard R.

1999-01-01

One difficulty in using Kalman filters in real world situations is the selection of the correct process noise, measurement noise, and initial state estimate and covariance. These parameters are commonly referred to as tuning parameters. Multiple methods have been developed to estimate these parameters. Most of those methods such as maximum likelihood, subspace, and observer Kalman Identification require extensive offline processing and are not suitable for real time processing. One technique, which is suitable for real time processing, is the residual tuning method. Any mismodeling of the filter tuning parameters will result in a non-white sequence for the filter measurement residuals. The residual tuning technique uses this information to estimate corrections to those tuning parameters. The actual implementation results in a set of sequential equations that run in parallel with the Kalman filter. Equations for the estimation of the measurement noise have also been developed. These algorithms are used to estimate the process noise and measurement noise for the Wide Field Infrared Explorer star tracker and gyro.

Reactivity study on thermal cracking of vacuum residues

NASA Astrophysics Data System (ADS)

León, A. Y.; Díaz, S. D.; Rodríguez, R. C.; Laverde, D.

2016-02-01

This study focused on the process reactivity of thermal cracking of vacuum residues from crude oils mixtures. The thermal cracking experiments were carried out under a nitrogen atmosphere at 120psi between 430 to 500°C for 20 minutes. Temperature conditions were established considering the maximum fractional conversion reported in tests of thermogravimetry performed in the temperature range of 25 to 600°C, with a constant heating rate of 5°C/min and a nitrogen flow rate of 50ml/min. The obtained products were separated in to gases, distillates and coke. The results indicate that the behaviour of thermal reactivity over the chemical composition is most prominent for the vacuum residues with higher content of asphaltenes, aromatics, and resins. Finally some correlations were obtained in order to predict the weight percentage of products from its physical and chemical properties such as CCR, SARA (saturates, aromatics, resins, asphaltenes) and density. The results provide new knowledge of the effect of temperature and the properties of vacuum residues in thermal conversion processes.

Identification of multi-insecticide residues using GC-NPD and the degradation kinetics of chlorpyrifos in sweet corn and soils.

PubMed

Wang, Peidan; Rashid, Muhammad; Liu, Jie; Hu, Meiying; Zhong, Guohua

2016-12-01

Because more than one insecticide is applied to crops to protect plants from pests, an analytical multi-residue determination method was developed using gas chromatography with a nitrogen phosphorus detector (GC-NPD). The retention time for 12 insecticides was 3.7-27.7min. Under the selected conditions, the limits of detection (LOD) and quantification (LOQ) were below the maximum residue limits (MRLs) and in the range of 0.00315-0.05μgmL(-1) and 0.01-0.165μgmL(-1), respectively. Using GC-NPD, we investigated the dissipation dynamics and final residual levels of chlorpyrifos in sweet corn and soil and determined that the half-lives was 4-7days, that is, that chlorpyrifos is safe to use on sweet corn with a pre-harvest interval of 16-22days before harvest. These results provide new insights into chlorpyrifos degradation in plants and its environmental behavior. Copyright © 2016. Published by Elsevier Ltd.

Effects of acid impregnated steam explosion process on xylose recovery and enzymatic conversion of cellulose in corncob.

PubMed

Fan, Xiaoguang; Cheng, Gang; Zhang, Hongjia; Li, Menghua; Wang, Shizeng; Yuan, Qipeng

2014-12-19

Corncob residue is a cellulose-rich byproduct obtained from industrial xylose production via dilute acid hydrolysis processes. Enzymatic hydrolysis of cellulose in acid hydrolysis residue of corncob (AHRC) is often less efficient without further pretreatment. In this work, the process characteristics of acid impregnated steam explosion were studied in conjunction with a dilute acid process, and their effects on physiochemical changes and enzymatic saccharification of corncob residue were compared. With the acid impregnated steam explosion process, both higher xylose recovery and higher cellulose conversion were obtained. The maximum conversion of cellulose in acid impregnated steam explosion residue of corncob (ASERC) reached 85.3%, which was 1.6 times higher than that of AHRC. Biomass compositional analysis showed similar cellulose and lignin content in ASERC and AHRC. XRD analysis demonstrated comparable crystallinity of ASERC and AHRC. The improved enzymatic hydrolysis efficiency was attributed to higher porosity in ASERC, measured by mercury porosimetry. Copyright © 2014 Elsevier Ltd. All rights reserved.

Occurrence and human dietary assessment of fluoroquinolones antibiotics in cultured fish around tai lake, China.

PubMed

Song, Chao; Zhang, Cong; Kamira, Barry; Qiu, Liping; Fan, Limin; Wu, Wei; Meng, Shunlong; Hu, Gengdong; Chen, Jiazhang

2017-11-01

Fluoroquinolone antibiotics are widely used in the production of aquatic products and considered to be a significant contributing factor to the burden of both natural and aquaculture environments. However, the main types of fluoroquinolones present in aquaculture systems have not been determined. The objectives of the present study were to explore the occurrence of residual fluoroquinolone antibiotics in fish muscle tissues sampled from across the entire aquaculture season in the Tai Lake basin in China and to assess the dietary risks associated with the upcoming vendible fish in the last month of the aquaculture season. Fluoroquinolones were detected in 95.69% of all fish samples, and the concentrations ranged from the limit of quantification (LOQ) to 47 108.00 μg · kg -1 . Enrofloxacin contributed the most among the 9 fluoroquinolone antibiotics tested. Of the 4 fish species studied, enrofloxacin was present in bream at significant (p < 0.05) concentrations in August, with an average value of 321.45 μg · kg -1 , while enrofloxacin concentrations peaked in crab and shrimp in September, with average values of 6949.60 and 460.82 μg · kg -1 , respectively. However, different patterns were observed in perch, suggesting that other categories of antibiotics may be used in the production of this fish. Dietary risk assessment showed that the residual levels and estimated daily intake in bream, perch, and shrimp were far below the maximum residual level and acceptable daily intake. However, the average residual level in crab exceeded the maximum residual level, and the estimated daily intake value accounted for 78.49% of the acceptable daily intake, indicating potential consumption risk. In summary, the present study aims to guide the production and consumption of aquatic products. Environ Toxicol Chem 2017;36:2899-2905. © 2017 SETAC. © 2017 SETAC.

Incorporation of Tyrosine and Glutamine Residues into the Soluble Guanylate Cyclase Heme Distal Pocket Alters NO and O2 Binding*

PubMed Central

Derbyshire, Emily R.; Deng, Sarah; Marletta, Michael A.

2010-01-01

Nitric oxide (NO) is the physiologically relevant activator of the mammalian hemoprotein soluble guanylate cyclase (sGC). The heme cofactor of α1β1 sGC has a high affinity for NO but has never been observed to form a complex with oxygen. Introduction of a key tyrosine residue in the sGC heme binding domain β1(1–385) is sufficient to produce an oxygen-binding protein, but this mutation in the full-length enzyme did not alter oxygen affinity. To evaluate ligand binding specificity in full-length sGC we mutated several conserved distal heme pocket residues (β1 Val-5, Phe-74, Ile-145, and Ile-149) to introduce a hydrogen bond donor in proximity to the heme ligand. We found that the NO coordination state, NO dissociation, and enzyme activation were significantly affected by the presence of a tyrosine in the distal heme pocket; however, the stability of the reduced porphyrin and the proteins affinity for oxygen were unaltered. Recently, an atypical sGC from Drosophila, Gyc-88E, was shown to form a stable complex with oxygen. Sequence analysis of this protein identified two residues in the predicted heme pocket (tyrosine and glutamine) that may function to stabilize oxygen binding in the atypical cyclase. The introduction of these residues into the rat β1 distal heme pocket (Ile-145 → Tyr and Ile-149 → Gln) resulted in an sGC construct that oxidized via an intermediate with an absorbance maximum at 417 nm. This absorbance maximum is consistent with globin FeII-O2 complexes and is likely the first observation of a FeII-O2 complex in the full-length α1β1 protein. Additionally, these data suggest that atypical sGCs stabilize O2 binding by a hydrogen bonding network involving tyrosine and glutamine. PMID:20231286

Pesticide Residues on Three Cut Flower Species and Potential Exposure of Florists in Belgium.

PubMed

Toumi, Khaoula; Vleminckx, Christiane; van Loco, Joris; Schiffers, Bruno

2016-09-23

In order to assess the prevalence of pesticide contamination and the risk of florists' exposure when handling cut flowers, sampling and analysis of 90 bouquets of the most commonly sold cut flowers in Belgium (50 bouquets of roses; 20 of gerberas, and 20 of chrysanthemums) were carried out. The bouquets were collected from 50 florists located in the seven largest cities of Belgium (Antwerp, Brussels, Charleroi, Ghent, Leuven, Liege, and Namur) and from five supermarkets located in the different regions. To have a better understanding of the route of exposure and professional practices a questionnaire was also addressed to a group of 25 florists who volunteered to take part in the survey. All florists were interviewed individually when collecting the questionnaire. The residual pesticide deposit values on cut flowers were determined in an accredited laboratory using a multi-residue (QuEChERS Quick Easy Cheap Effective Rugged Safe) method and a combination of gas chromatography (GC) and liquid chormatograhphy (LC) analysis. A total of 107 active substances were detected from all samples; i.e., an average of about 10 active substances per bouquet. The most severely contaminated bouquet accumulated a total concentration of residues up to 97 mg/kg. Results show that roses are the most contaminated cut flowers; with an average of 14 substances detected per sample and a total concentration per rose sample of 26 mg/kg. Some active substances present an acute toxicity (acephate, methiocarb, monocrotophos, methomyl, deltamethrin, etc.) and exposure can generate a direct effect on the nervous system of florists. Nevertheless, fungicides (dodemorph, propamocarb, and procymidone) were the most frequently detected in samples and had the highest maximum concentrations out of all the active substances analysed. Dodemorph was the most frequently detected substance with the highest maximum concentration (41.9 mg/kg) measured in the rose samples. It appears from the survey that, despite being exposed to high deposits of residues, florists usually do not protect themselves from contact with residues even if they spend several hours handling cut flowers and preparing bouquets (from 2 to 6 h/day, depending on the time of year and/or selling periods) daily. Bad habits (eating, drinking, or smoking at work) and absence of personal protective equipment of most florists also increase the risk of contact with pesticide residues.

Pesticide Residues on Three Cut Flower Species and Potential Exposure of Florists in Belgium

PubMed Central

Toumi, Khaoula; Vleminckx, Christiane; van Loco, Joris; Schiffers, Bruno

2016-01-01

In order to assess the prevalence of pesticide contamination and the risk of florists’ exposure when handling cut flowers, sampling and analysis of 90 bouquets of the most commonly sold cut flowers in Belgium (50 bouquets of roses; 20 of gerberas, and 20 of chrysanthemums) were carried out. The bouquets were collected from 50 florists located in the seven largest cities of Belgium (Antwerp, Brussels, Charleroi, Ghent, Leuven, Liege, and Namur) and from five supermarkets located in the different regions. To have a better understanding of the route of exposure and professional practices a questionnaire was also addressed to a group of 25 florists who volunteered to take part in the survey. All florists were interviewed individually when collecting the questionnaire. The residual pesticide deposit values on cut flowers were determined in an accredited laboratory using a multi-residue (QuEChERS Quick Easy Cheap Effective Rugged Safe) method and a combination of gas chromatography (GC) and liquid chormatograhphy (LC) analysis. A total of 107 active substances were detected from all samples; i.e., an average of about 10 active substances per bouquet. The most severely contaminated bouquet accumulated a total concentration of residues up to 97 mg/kg. Results show that roses are the most contaminated cut flowers; with an average of 14 substances detected per sample and a total concentration per rose sample of 26 mg/kg. Some active substances present an acute toxicity (acephate, methiocarb, monocrotophos, methomyl, deltamethrin, etc.) and exposure can generate a direct effect on the nervous system of florists. Nevertheless, fungicides (dodemorph, propamocarb, and procymidone) were the most frequently detected in samples and had the highest maximum concentrations out of all the active substances analysed. Dodemorph was the most frequently detected substance with the highest maximum concentration (41.9 mg/kg) measured in the rose samples. It appears from the survey that, despite being exposed to high deposits of residues, florists usually do not protect themselves from contact with residues even if they spend several hours handling cut flowers and preparing bouquets (from 2 to 6 h/day, depending on the time of year and/or selling periods) daily. Bad habits (eating, drinking, or smoking at work) and absence of personal protective equipment of most florists also increase the risk of contact with pesticide residues. PMID:27669276

SU-F-T-57: Delivered Activity Accuracy of Radium 223 Dichloride Injections, When Being Administrated for Castration Resistant Prostate Cancer, Symptomatic Bone Metastases. The Impact of Residual Activity in the Spent Syringe and Dispensing Accuracy of Ra 223

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jennings, G

Purpose: To quantify the delivered activity accuracy of Radium 223 dichloride injections, when being administrated for castration – resistant prostate cancer, symptomatic bone metastases. The impact of residual activity in the spent syringe and dispensing accuracy of Ra 223. Methods: The administration is by slow intravenous injection over 1 minute followed by double flushing of the 10 mL syringe and IV with saline. Eighty (80) procedures was used to investigate variations in the activity from the amount prescribed (µCi) = 1.35 × Patient weight Kg. The Activity dispensed into a 10mL syringe using a NIST traceable Capintec CRC-25R Chamber andmore » a cross calibrated capintec CRC-15R to measure activity in the syringe immediately before and after administration Results: The patients weight range from 121Ib to 235lb and doses ranging 74.25 µCi to 144.2 µCi. The deviation of dispensed dose vs Prescribed dose average +2.1% with a range of −1.1% to +5.7%. The Dose measured before administration ranges 79.3 µCi to 154.9 µCi. Deviation from the dispensed dose was show to average +2.9% with a range of −0.8% to +7.3%. The average residual dose post injection was 2.5 µCi or 2.2% of the pre injection activity. Ranging from 0.9 µCi to 6.2 µCi, 0.7% to 5.4% respectively. Subtracting the residual activity from that measured activity before injection and comparing it to prescription dose was shown to have an average variation of +2.7% with a range of −0.8% to 7.4%. Conclusion: The case resulted in the 6.2 µCi maximum residual dose had two syringes. A small, 82.8 µCi activity, case resulted in the 7.4% maximum variation in measures less residual verses prescription dose. The average +2.1 % dispenses activity of Ra 223 over the prescription dosage was seen to counteract the average 2.2% residual dosage found to remain in the syringe.« less

75 FR 17083 - Fiduciary Duties at Federal Credit Unions; Mergers and Conversions of Insured Credit Unions...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... Credit Unions; Mergers and Conversions of Insured Credit Unions; Correction AGENCY: National Credit Union... Federal credit unions and mergers and conversions of insured credit unions. The proposed rule as published... Conversions of Insured Credit Unions) in the e-mail subject line.'' [[Page 17084

Elimination of trait blocks from multiple trait mixed model equations with singular (Co)variance parameter matrices

USDA-ARS?s Scientific Manuscript database

Transformations to multiple trait mixed model equations (MME) which are intended to improve computational efficiency in best linear unbiased prediction (BLUP) and restricted maximum likelihood (REML) are described. It is shown that traits that are expected or estimated to have zero residual variance...

NAFTA Guidance Document on Data Requirements for Tolerances on Imported Commodities in the United States and Canada

EPA Pesticide Factsheets

The purpose of this document is to provide detailed guidance on data requirements that meet the North American Free Trade Agreement standards for the establishment of pesticide import tolerances or maximum residue levels in Canada and the United States.

Polychlorinated biphenyls, mercury, and potential endocrine disruption in fish from the Hudson River, New York, USA

USGS Publications Warehouse

Baldigo, Barry P.; Sloan, R.J.; Smith, S.B.; Denslow, N.D.; Blazer, V.S.; Gross, T.S.

2006-01-01

Tissue residues of total mercury (Hg), total polychlorinated biphenyls (PCBs), and lipid-based PCBs; plasma concentrations of endocrine biomarkers; and reproductive and histologic biomarkers were assessed in 460 carp (Cyprinus carpio), bass (Micropterus salmoides and Micropterus dolomieui), and bullhead (Ameiurus nebulosus) collected from eight sites across the Hudson River Basin in the spring of 1998 to determine if endocrine disruption was evident in resident fish species and to evaluate contaminant-biomarker interrelations. Total PCBs in bed sediments (maximum 2,500 ??g kg-1) could explain 64 to 90% of the variability in lipid-based PCB residues in tissues (maximum 1,250 ??g PCB g-lipid-1) of the four species. The 17??-estradiol to 11-ketotestosterone ratio, typically less than 1.0 in male fish and greater than 1.0 in females, exceeded 1.4 in all male largemouth bass and 35% of male carp and bullhead at one site 21 km downstream from a major PCB source. Endocrine biomarkers were significantly correlated with total Hg in female smallmouth bass and carp, and with lipid-based PCBs in males of all four species. Empirical evidence of endocrine modulation in blood plasma of male and female fish from sites with and without high PCB residues in bed sediments and fish tissues suggest that PCBs, Hg, or other contaminants may disrupt normal endocrine function in fish of the Hudson River. ?? Eawag, 2006.

Detection of Unexpected High Correlations between Balance Calibration Loads and Load Residuals

NASA Technical Reports Server (NTRS)

Ulbrich, N.; Volden, T.

2014-01-01

An algorithm was developed for the assessment of strain-gage balance calibration data that makes it possible to systematically investigate potential sources of unexpected high correlations between calibration load residuals and applied calibration loads. The algorithm investigates correlations on a load series by load series basis. The linear correlation coefficient is used to quantify the correlations. It is computed for all possible pairs of calibration load residuals and applied calibration loads that can be constructed for the given balance calibration data set. An unexpected high correlation between a load residual and a load is detected if three conditions are met: (i) the absolute value of the correlation coefficient of a residual/load pair exceeds 0.95; (ii) the maximum of the absolute values of the residuals of a load series exceeds 0.25 % of the load capacity; (iii) the load component of the load series is intentionally applied. Data from a baseline calibration of a six-component force balance is used to illustrate the application of the detection algorithm to a real-world data set. This analysis also showed that the detection algorithm can identify load alignment errors as long as repeat load series are contained in the balance calibration data set that do not suffer from load alignment problems.

Cross-bridge mechanism of residual force enhancement after stretching in a skeletal muscle.

PubMed

Tamura, Youjiro

2018-01-01

A muscle model that uses a modified Langevin equation with actomyosin potentials was used to describe the residual force enhancement after active stretching. Considering that the new model uses cross-bridge theory to describe the residual force enhancement, it is different from other models that use passive stretching elements. Residual force enhancement was simulated using a half sarcomere comprising 100 myosin molecules. In this paper, impulse is defined as the integral of an excess force from the steady isometric force over the time interval for which a stretch is applied. The impulse was calculated from the force response due to fast and slow muscle stretches to demonstrate the viscoelastic property of the cross-bridges. A cross-bridge mechanism was proposed as a way to describe the residual force enhancement on the basis of the impulse results with reference to the compliance of the actin filament. It was assumed that the period of the actin potential increased by 0.5% and the amplitude of the potential decreased by 0.5% when the half sarcomere was stretched by 10%. The residual force enhancement after 21.0% sarcomere stretching was 6.9% of the maximum isometric force of the muscle; this value was due to the increase in the number of cross-bridges.

High-Throughput Analytical Techniques for the Determination of the Residues of 653 Multiclass Pesticides and Chemical Pollutants in Tea, Part VII: A GC-MS, GC-MS/MS, and LC-MS/MS Study of the Degradation Profiles of Pesticide Residues in Green Tea.

PubMed

Chang, Qiao-Ying; Pang, Guo-Fang; Fan, Chun-Lin; Chen, Hui; Yang, Fang; Li, Jie; Wen, Bi-Fang

2016-11-01

GC-MS, GC-tandem MS (MS/MS), and LC-MS/MS were used to mathematically define the degradation profiles of pesticide residues in two field trials. Nineteen pesticides were studied in the first field trial and 11 in the second. The results of the field trials demonstrated that the degradation profiles of pesticide residues in green tea can be described with power functions to successfully estimate the amount of time, following pesticide application, pesticide residues appearing in tea in concentrations at and/or above the maximum residue limit (MRL) decrease to concentrations below the MRL. Stability tests on green tea samples stored at room temperature were conducted to determine whether pesticide-incurred green tea samples prepared according to the method used in the field trials would be suitable for the preparation of reference standards for laboratory-proficiency testing trials. This paper reports the results of a GC-MS, GC-MS/MS, and LC-MS/MS study, as well as the suitability of the samples prepared under these conditions for use as pesticide reference standards in tea analysis.

Evaluation of certain veterinary drug residues in food. Eighty-first report of the Joint FAO/WHO Expert Committee on Food Additives.

PubMed

2016-01-01

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of residues of certain veterinary drugs in food and to recommend maximum levels for such residues in food. The first part of the report considers general principles regarding the evaluation of residues of veterinary drugs within the terms of reference of the Joint FAO/WHO Expert Committee on Food Additives (JECFA), including MRLs for generic fish species, acute reference doses (ARfDs) for veterinary drugs, an approach for dietary exposure assessment of compounds used for multiple purposes (i.e veterinary drugs and pesticides), dietary exposure assessment for less-than-lifetime exposure, and the assessment of short-term (90-day and 12-month) studies in dogs. Summaries follow of the Committee's evaluations of toxicological and residue data on a variety of veterinary drugs: two insecticides (diflubenzuron and teflubenzuron), an antiparasitic agent (ivermectin), an ectoparasiticide (sisapronil) and a β2-adrenoceptor agonist (zilpaterol hydrochloride). In addition, the Committee considered issues raised in concern forms from the Codex Committee on Residues of Veterinary Drugs in Foods on lasalocid sodium, an antiparasitic agent. Annexed to the report is a summary of the Committee's recommendations on these drugs, including acceptable daily intakes (ADIs), ARfDs and proposed MRLs.

Food safety in Thailand. 3: Pesticide residues detected in mangosteen (Garcinia mangostana L.), queen of fruits.

PubMed

Phopin, Kamonrat; Wanwimolruk, Sompon; Prachayasittikul, Virapong

2017-02-01

For developing countries like Thailand, regulation of pesticide usage exists, but it is not fully enforced. Therefore, pesticide residues in vegetables and fruits have not been well monitored. This study aimed to determine the pesticide residues in mangosteen fruits sold in Thailand. The mangosteen samples (n = 111) were purchased and the contents of 28 pesticides were analysed by GC-MS/MS method. Of the pesticides tested, eight were found in 100% of the mangosteen samples. However, in 97% of these samples, either chlorothalonil, chlorpyrifos, diazinon, dimethoate, metalaxyl or profenofos was detected exceeding their maximum residue limits (MRLs), representing a 97% rate of pesticide detection above the MRL. This rate is much higher than those found in other fruits sold in developed countries. However, this conclusion excludes the fresh Thai mangosteens grown for export, as these are generally cultivated and harvested to GAP standards. Since the edible part of the mangosteen is the pulp, washing the fruits with running water can reduce the risk of pesticide residues contaminating the pulp which would be eaten by the consumer. The findings strongly suggest that routine monitoring of pesticide residues in fruits and vegetables is required to reduce the health risks associated with consuming contaminated food. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Determination of lasalocid residues in the tissues of broiler chickens by liquid chromatography-tandem mass spectrometry.

PubMed

Tkáčiková, Soňa; Kožárová, Ivona; Mačanga, Ján; Levkut, Martin

2012-01-01

Lasalocid is a polyether ionophoric coccidiostat used for the prevention of coccidiosis in poultry at a prescribed concentration and during a certain time interval. Due to a public health concern about the presence of coccidiostat residues in poultry, the aim of the present study was to determine the levels of lasalocid residues in the edible tissues of broiler chickens (breast muscle, thigh muscle, heart, liver, gizzard, kidneys and skin/fat) fed commercially produced feed containing 100 mg kg⁻¹) of lasalocid in complete feed throughout the 5-day withdrawal period (WP). The residues were investigated by liquid chromatography coupled with electrospray ionisation (ESI) tandem mass spectrometry (MS/MS) with triple quadrupole. The limit of detection (LOD) and the limit of quantification (LOQ) of the method were 0.47 and 1.44 µg kg⁻¹, respectively. The average recovery based on the matrix-fortified calibrations for chicken tissues ranged between 79% and 98%. Lasalocid was found to accumulate in the liver, followed by the heart, skin/fat, kidneys, thigh muscle and gizzard. The lowest concentrations of lasalocid residues were found in the breast muscle. On day 5 of the WP, residue concentrations of lasalocid did not decline below the LOQ of the method, but were far below the maximum residue level (MRL) established for lasalocid in poultry from 20 to 100 µg kg⁻¹ by European Commission Regulation (EU) No. 37/2010. The results confirmed that the WP established for lasalocid is sufficient to ensure the decline of its residues in the tissues of broiler chickens to the safe residue level.

Climate change mitigation effect of harvested wood products in regions of Japan.

PubMed

Kayo, Chihiro; Tsunetsugu, Yuko; Tonosaki, Mario

2015-12-01

Harvested wood products (HWPs) mitigate climate change through carbon storage, material substitution, and energy substitution. We construct a model to assess the overall climate change mitigation effect (comprising the carbon storage, material substitution, and energy substitution effects) resulting from HWPs in regions of Japan. The model allows for projections to 2050 based on future scenarios relating to the domestic forestry industry, HWP use, and energy use. Using the production approach, a nationwide maximum figure of 2.9 MtC year -1 for the HWP carbon storage effect is determined for 2030. The maximum nationwide material substitution effect is 2.9 MtC year -1 in 2050. For the energy substitution effect, a nationwide maximum projection of 4.3 MtC year -1 in 2050 is established, with at least 50 % of this figure derived from east and west Japan, where a large volume of logging residue is generated. For the overall climate change mitigation effect, a nationwide maximum projection of 8.4 MtC year -1 in 2050 is established, equivalent to 2.4 % of Japan's current carbon dioxide emissions. When domestic roundwood production and HWP usage is promoted, an overall climate change mitigation effect is consistently expected to be attributable to HWPs until 2050. A significant factor in obtaining the material substitution effect will be substituting non-wooden buildings with wooden ones. The policy of promoting the use of logging residue will have a significant impact on the energy substitution effect. An important future study is an integrated investigation of the climate change mitigation effect for both HWPs and forests.

Dynamic Contrast-Enhanced Magnetic Resonance Imaging With Gadolinium Ethoxybenzyl Diethylenetriamine Pentaacetic Acid for Quantitative Assessment of Vascular Effects on Hepatocellular-Carcinoma Lesions Treated by Transarterial Chemoembolization or Radiofrequency Ablation.

PubMed

Ippolito, Davide; Trattenero, Chiara; Talei Franzesi, Cammillo; Casiraghi, Alessandra; Lombardi, Sophie; Vacirca, Francesco; Corso, Rocco; Sironi, Sandro

2016-01-01

The aim of this study was to investigate the role of dynamic contrast-enhanced magnetic resonance imaging (MRI) in evaluation of blood flow changes related to transarterial chemoembolization (TACE) and radiofrequency ablation (RFA) procedures in patients with hepatocellular carcinoma (HCC) lesions. Fifty-four patients, with biopsy-proven HCC, who underwent TACE or RFA, were evaluated, 1 month after treatment, with upper abdominal MRI examination. Multiplanar T2-weighted, T1-weighted, and dynamic contrast-enhanced sequences were acquired. Dedicated perfusion software (T1 Perfusion Package, Viewforum; Philips Medical Systems, The Netherlands) was used to generate color permeability maps. After placing regions of interest in normal hepatic parenchyma, in successfully treated lesions, and in area of recurrence, the following perfusion parameters were calculated and statistically analyzed: relative arterial, venous, and late enhancement; maximum enhancement; maximum relative enhancement, and time to peak. Twenty-one of 54 patients had residual disease, and perfusion parameters values measured within tumor tissue were: relative arterial enhancement median, 42%; relative venous enhancement median, 69%; relative late enhancement median, 57.7%; maximum enhancement median, 749.6%; maximum relative enhancement median, 69%; time to peak median, 81.1 seconds. As for all the evaluated parameters, a significant difference (P < 0.05) was found between residual viable tumor tissue and effective treated lesions. Dynamic contrast-enhanced MRI represents a complementary noninvasive tool that may offer quantitative and qualitative information about HCC lesions treated with TACE and RFA.

Rib biomechanical properties exhibit diagnostic potential for accurate ageing in forensic investigations

PubMed Central

Bonicelli, Andrea; Xhemali, Bledar; Kranioti, Elena F.

2017-01-01

Age estimation remains one of the most challenging tasks in forensic practice when establishing a biological profile of unknown skeletonised remains. Morphological methods based on developmental markers of bones can provide accurate age estimates at a young age, but become highly unreliable for ages over 35 when all developmental markers disappear. This study explores the changes in the biomechanical properties of bone tissue and matrix, which continue to change with age even after skeletal maturity, and their potential value for age estimation. As a proof of concept we investigated the relationship of 28 variables at the macroscopic and microscopic level in rib autopsy samples from 24 individuals. Stepwise regression analysis produced a number of equations one of which with seven variables showed an R2 = 0.949; a mean residual error of 2.13 yrs ±0.4 (SD) and a maximum residual error value of 2.88 yrs. For forensic purposes, by using only bench top machines in tests which can be carried out within 36 hrs, a set of just 3 variables produced an equation with an R2 = 0.902 a mean residual error of 3.38 yrs ±2.6 (SD) and a maximum observed residual error 9.26yrs. This method outstrips all existing age-at-death methods based on ribs, thus providing a novel lab based accurate tool in the forensic investigation of human remains. The present application is optimised for fresh (uncompromised by taphonomic conditions) remains, but the potential of the principle and method is vast once the trends of the biomechanical variables are established for other environmental conditions and circumstances. PMID:28520764

[Predictors of physical incapacity degree to chronic hemodialysis patients in Kinshasa : Key role of the residual diuresis].

PubMed

Mokoli, Vieux Momeme; Bukabau, Justine Busanga; Izeidi, Patrick Parmba Osa; Luse, Jeanine Losa; Mukendi, Stéphane Kalambay; Mashinda, Désiré Kulimba; Makulo, Jean Robert Rissassy; Sumaili, Ernest Kiswaya; Lepira, François Bompeka; Nseka, Nazaire Mangani

2016-12-01

Identifying predictors of physical incapacity degree in patients on chronic hemodialysis in Kinshasa. Bicentric analytical study, between January 2007 and July 2013. Degree of physical handicap was evaluated at 6months of hemodialysis based on the scale of Rosser. Logistic regression sought the predictors of no or light physical incapacity (Rosser<3) vs. moderate to maximum (Rosser≥3). P was set at 0.05. One hundred twenty-seven patients (127) patients received at least 6months of hemodialysis (53.3±11years; 73.2 % male), 79 (62.2 %) had no or light incapacity and 48 (37.8 %) moderate to maximum. Predictors of lower physical incapacity in univaried analysis were: secured funding, high socioeconomic level, lack of diabetes mellitus, high body weight, normal systolic and diastolic blood pressure, residual diuresis 3months later, hemoglobin and hematocrit, low comorbidity, arteriovenous fistula, erythropoietin, at least 12hours of hemodialysis per week and lack of intradialytic complications. After logistic regression, a high residual diuresis 3months of hemodialysis has proved an independent predictor of lower physical Incapacity (aOR 0.998; P=0.024) next to the lack of diabetes mellitus (aOR 0.239; P=0.024), good control of systolic (aOR 0.958; P=0.013) and diastolic (aOR 1.089; P=0.003) blood pressure and the use of erythropoietin (aOR 5.687; P=0.004). Preserving residual diuresis is associated with lower physical incapacity and must be integrated in the management in hemodialysis. Copyright © 2016 Association Société de néphrologie. Published by Elsevier SAS. All rights reserved.

A framework for streamflow prediction in the world's most severely data-limited regions: Test of applicability and performance in a poorly-gauged region of China

NASA Astrophysics Data System (ADS)

Alipour, M. H.; Kibler, Kelly M.

2018-02-01

A framework methodology is proposed for streamflow prediction in poorly-gauged rivers located within large-scale regions of sparse hydrometeorologic observation. A multi-criteria model evaluation is developed to select models that balance runoff efficiency with selection of accurate parameter values. Sparse observed data are supplemented by uncertain or low-resolution information, incorporated as 'soft' data, to estimate parameter values a priori. Model performance is tested in two catchments within a data-poor region of southwestern China, and results are compared to models selected using alternative calibration methods. While all models perform consistently with respect to runoff efficiency (NSE range of 0.67-0.78), models selected using the proposed multi-objective method may incorporate more representative parameter values than those selected by traditional calibration. Notably, parameter values estimated by the proposed method resonate with direct estimates of catchment subsurface storage capacity (parameter residuals of 20 and 61 mm for maximum soil moisture capacity (Cmax), and 0.91 and 0.48 for soil moisture distribution shape factor (B); where a parameter residual is equal to the centroid of a soft parameter value minus the calibrated parameter value). A model more traditionally calibrated to observed data only (single-objective model) estimates a much lower soil moisture capacity (residuals of Cmax = 475 and 518 mm and B = 1.24 and 0.7). A constrained single-objective model also underestimates maximum soil moisture capacity relative to a priori estimates (residuals of Cmax = 246 and 289 mm). The proposed method may allow managers to more confidently transfer calibrated models to ungauged catchments for streamflow predictions, even in the world's most data-limited regions.

The physical demands of Super 14 rugby union.

PubMed

Austin, Damien; Gabbett, Tim; Jenkins, David

2011-05-01

The purpose of the present study was to describe the match-play demands of professional rugby union players competing in Super 14 matches during the 2008 and 2009 seasons. The movements of 20 players from Super 14 rugby union team during the 2008 and 2009 seasons were video recorded. Using time-motion analysis (TMA), five players from four positional groups (front-row forwards, back-row forwards, inside backs and outside backs) were assessed. Players covered between 4218 m and 6389 m during the games. The maximum distances covered in a game by the four groups were: front row forwards (5139 m), back row forwards, (5422 m), inside backs (6389 m) and outside backs (5489 m). The back row forwards spent the greatest amount of time in high-intensity exercise (1190 s), followed by the front row forwards (1015 s), the inside backs (876 s) and the outside backs (570 s). Average distances covered in individual sprint efforts were: front row forwards (16 m), back row forwards (14 m), inside backs (17 m) and outside backs (18 m). Work to rest ratios of 1:4, 1:4, 1:5, and 1:6 were found for the front row and back row forwards, and inside and outside backs respectively. The Super 14 competition during 2008 and 2009, have resulted in an increase in total high-intensity activities, sprint frequency, and work to rest ratios across all playing positions. For players and teams to remain competitive in Super 14 rugby, training (including recovery practices) should reflect these current demands. Copyright © 2011 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Analyses of ozone in urban and rural sites in Málaga (Spain).

PubMed

Dueñas, C; Fernández, M C; Cañete, S; Carretero, J; Liger, E

2004-08-01

Ozone concentrations were measured at two (urban and a rural) sites near the city of Málaga (Spain). The aim of this study was to determine the daily, monthly and seasonal variation patterns of ozone concentrations at both sites and to study the possible regional influences. The daily variations mostly have the usual features with the afternoon maximum and the night minimum being more pronounced in the urban area. The average monthly concentrations throughout the year start to increase in March reaching their maximum values in July for the urban site. However, in the rural area, the monthly variations are smaller reaching their maximum value in June. The hourly evolution of the ozone concentrations in both sampling sites is well defined in spring and summer and not so well defined in autumn and winter. Taking into account the four seasons, the rural concentrations are higher than the urban ones. Summer is the season when there are similar concentrations at both sampling sites. Average hourly summer afternoon ozone for the hours 12:00-20:00 LST exceeded the 110 microg m(-3) European Union guidelines for human health for 8 h ozone exposure at the urban and rural sites.

Characteristics of the LacTek test as applied to tissue samples: assessment of performance using incurred field samples.

PubMed

Mitchell, J M; McNab, W B; Yee, A J; Griffiths, M W; McEwen, S A; Spilsbury, L; Boison, J O

1998-08-01

The Lactek test, marketed for antimicrobial residue detection in milk, was validated for the detection of antimicrobial residues in tissues. A previous study found that the LacTek test could confidently identify tissue samples spiked with antimicrobial residues. However, the test could not reliably distinguish violative from nonviolative spiked samples relative to Canadian maximum residue limits (MRLs). The objectives of this study were to assess and compare the performance of the LacTek tests for beta-lactams, tetracyclines, gentamicin, and sulfamethazine on samples containing naturally incurred residues by running the test in parallel with the standard microbial inhibition test (MIT) presently used for the routine testing of tissues at our facility and to assess the agreement with high pressure liquid chromatographic (HPLC) determinative methods. Parallel testing with the official MIT found that the Lactek tests could be confidently used for testing tissue samples containing incurred residues. Among 1,008 MIT-positive samples, the LacTek test found that 90% contained beta-lactams and/or tetracyclines. A further 7.3% of violative residues could not be identified to an antimicrobial class. In addition, 9% of samples testing negative on the MIT were found to contain an antimicrobial residue by the LacTek tests. Comparative testing with HPLC methods found that there was very good agreement between the two tests and that most violations were due to penicillin G and oxytetracycline. Although the LacTek test cannot be used to distinguish violative from nonviolative residue levels, it does offer several advantages over the present MIT. These include speed, ease of use, the ability to identify residues to a specific class, and an improved sensitivity at the MRL level for the most commonly found antimicrobials in tissue.

Confirmatory analysis of 17beta-boldenone, 17alpha-boldenone and androsta-1,4-diene-3,17-dione in bovine urine, faeces, feed and skin swab samples by liquid chromatography-electrospray ionisation tandem mass spectrometry.

PubMed

Nielen, Michel W F; Rutgers, Paula; van Bennekom, Eric O; Lasaroms, Johan J P; van Rhijn, J A Hans

2004-03-05

The origin, i.e. natural occurrence or illegal treatment, of findings of 17alpha-boldenone (alpha-Bol) and 17beta-boldenone (beta-Bol) in urine and faeces of cattle is under debate within the European Union. A liquid chromatographic positive ion electrospray tandem mass spectrometric method is presented for the confirmatory analysis of 17beta-boldenone, 17alpha-boldenone and an important metabolite/precursor androsta-1,4-diene-3,17-dione (ADD), using deuterium-labelled 17beta-boldenone (beta-Bol-d3) as internal standard. Detailed sample preparation procedures were developed for a variety of sample matrices such as bovine urine, faeces, feed and skin swab samples. The method was validated as a quantitative confirmatory method according to the latest EU guidelines and shows good precision, linearity and accuracy data, and CCalpha and CCbeta values of 0.1-0.3 and 0.4-1.0 ng/ml, respectively. Currently, the method has been successfully applied to suspect urine samples for more than a year, and occasionally to faeces, feed and swab samples as well. Results obtained from untreated and treated animals are given and their impact on the debate about the origin of residues of 17beta-boldenone is critically discussed. Finally, preliminary data about the degree of conjugation of boldenone residues are presented and a simple procedure for discrimination between residues from abuse versus natural origin is proposed.

Critical moisture content for microbial growth in dried food-processing residues.

PubMed

Rezaei, Farzaneh; Vandergheynst, Jean S

2010-09-01

Food-processing residues are good feedstocks for biofuel and biochemical production because they have high energy content and are abundant. Year-round biofuel and biochemical production requires proper storage to prevent microbial decomposition and thermal runaway. In this study, microbial activity of tomato pomace (TP), grape pomace (GP), fermented grape pomace (FGP) and sugar beet pulp (SBP) was monitored at nine different moisture contents. Maximum and cumulative respirations for each feedstock with respect to moisture content followed a sigmoidal relationship. The critical moisture content below which no microbial activity was detected for SBP, TP, FGP and GP was 24-31, 16-21, 23-33 and 43-46% (dry basis) respectively. A logarithmic relationship was observed (R(2) = 0.94) between critical moisture content and initial water-soluble carbohydrate (WSC) content of the processing residues. The critical moisture content below which no microbial activity was detected and the relationship between critical moisture content and initial WSC content were determined in this study for four food-processing residues. Both parameters permit evaluation of the potential for deterioration of food-processing residues during storage based on moisture content and WSC content. Copyright 2010 Society of Chemical Industry.

Residues of acephate and its metabolite methamidophos in/on mango fruit (Mangifera indica L.).

PubMed

Mohapatra, Soudamini; Ahuja, A K; Deepa, M; Sharma, Debi

2011-01-01

Mango, the major fruit crop of India is affected by stone weevil, which can cause serious damage to the fruits. Acephate gives good control of mango stone weevil. Residues of acephate and its major metabolite, methamidophos were evaluated on mango fruits following repeated spray applications at the recommended dose (0.75 kg a.i. ha⁻¹) and double the recommended dose (1.5 kg a.i. ha⁻¹). Acephate residues mostly remained on the fruit peel which persisted up to 30 days. Movement of residues to the fruit pulp was detected after 1 day of application, increased to maximum of 0.14 and 0.26 mg kg⁻¹ after 3 days and reached to below detectable level (BDL) after 20 days. Methamidophos, a metabolite of acephate, was detected from 3rd day onwards in both peel and pulp and persisted up to 15 days. The residues (acephate + methamidophos) dissipated with the half-life of 5 days in peel and pulp. A safe pre-harvest interval of 30 days is recommended for consumption of mango fruits following treatment of acephate at the recommended dose of 0.75 kg a.i. ha⁻¹.

Behavior of fluopyram and tebuconazole and some selected pesticides in ripe apples and consumer exposure assessment in the applied crop protection framework.

PubMed

Podbielska, Magdalena; Szpyrka, Ewa; Piechowicz, Bartosz; Zwolak, Aneta; Sadło, Stanisław

2017-07-01

The supervised field trials were conducted in a commercial apple orchard in 2016. The trials were an attempt to determine a model for dissipation and toxicological evaluation of fluopyram, tebuconazole, captan, tetrahydrophthalimide (THPI), pirimicarb, spirodiclofen, and boscalid residues detected in fruit of Red Jonaprince, Lobo, and Gala varieties immediately before harvest. The analysis also covered amounts of pesticides still present in remnants of calyx in Lobo and Gala varieties immediately before harvest. Laboratory samples of ripe apples were collected within 14 days of the treatment. Levels of pesticide residues detected in the samples changed at a constant exponential rate, and the residue levels found in ripe apples of Red Jonaprince, Gala, and Lobo varieties immediately before harvest were below maximum residue levels (MRL). Overall, captan residues in remnants of calyx were at a level of 22.3% for the Gala variety and 9.3% for the Lobo variety. Likewise, the long-term daily intake of the detected substances by a Polish adult consumer was low, ranging from 0.02% ADI for pirimicarb to 0.72% ADI for captan.

Multiclass methods for the analysis of antibiotic residues in milk by liquid chromatography coupled to mass spectrometry: A review.

PubMed

Rossi, Rosanna; Saluti, Giorgio; Moretti, Simone; Diamanti, Irene; Giusepponi, Danilo; Galarini, Roberta

2018-02-01

Milk is an important and beneficial food from a nutritional point of view, being an indispensable source of high quality proteins. Furthermore, it is a raw material for many dairy products, such as yoghurt, cheese, cream etc. Before reaching consumers, milk goes through production, processing and circulation. Each step involves potentially unsafe factors, such as chemical contamination that can affect milk quality. Antibiotics are widely used in veterinary medicine for dry cow therapy and mastitis treatment in lactating cows, which can cause the presence of antimicrobial residues in milk. In order to ensure consumers' safety, milk is analyzed to make sure that the fixed Maximum Residue Limits (MRLs) for antibiotics are not exceeded. Multiclass methods can monitor more drug classes through a single analysis, so they are faster, less time-consuming and cheaper than traditional methods (single-class); this aspect is particularly important for milk, which is a highly perishable food. Nevertheless, multiclass methods for veterinary drug residues in foodstuffs are real analytical challenges. This article reviews the major multiclass methods published for the determination of antibiotic residues in milk by liquid chromatography coupled to mass spectrometry, with a special focus on sample preparation approaches.

Automobile Shredder Residues in Italy: characterization and valorization opportunities.

PubMed

Fiore, S; Ruffino, B; Zanetti, M C

2012-08-01

At the moment Automobile Shredder Residue (ASR) is usually landfilled worldwide, but European draft Directive 2000/53/CE forces the development of alternative solutions, stating the 95%-wt recovery of an End of Life Vehicle (ELV) weight to be fulfilled by 2015. This work describes two industrial tests, each involving 250-300 t of ELVs, in which different pre-shredding operations were performed. The produced ASR materials underwent an extended characterization and some post-shredding processes, consisting of dimensional, magnetic, electrostatic and densimetric separation phases, were tested on laboratory scale, having as main purpose the enhancement of ASR recovery/recycling and the minimization of the landfilled fraction. The gathered results show that accurate depollution and dismantling operations are mandatory to obtain a high quality ASR material which may be recycled/recovered and partially landfilled according to the actual European Union regulations, with particular concern for Lower Heating Value (LHV), heavy metals content and Dissolved Organic Carbon (DOC) as critical parameters. Moreover post-shredding technical solutions foreseeing minimum economic and engineering efforts, therefore realizable in common European ELVs shredding plants, may lead to multi-purposed (material recovery and thermal valorization) opportunities for ASR reuse/recovery. Copyright © 2012 Elsevier Ltd. All rights reserved.

Image fusion method based on regional feature and improved bidimensional empirical mode decomposition

NASA Astrophysics Data System (ADS)

Qin, Xinqiang; Hu, Gang; Hu, Kai

2018-01-01

The decomposition of multiple source images using bidimensional empirical mode decomposition (BEMD) often produces mismatched bidimensional intrinsic mode functions, either by their number or their frequency, making image fusion difficult. A solution to this problem is proposed using a fixed number of iterations and a union operation in the sifting process. By combining the local regional features of the images, an image fusion method has been developed. First, the source images are decomposed using the proposed BEMD to produce the first intrinsic mode function (IMF) and residue component. Second, for the IMF component, a selection and weighted average strategy based on local area energy is used to obtain a high-frequency fusion component. Third, for the residue component, a selection and weighted average strategy based on local average gray difference is used to obtain a low-frequency fusion component. Finally, the fused image is obtained by applying the inverse BEMD transform. Experimental results show that the proposed algorithm provides superior performance over methods based on wavelet transform, line and column-based EMD, and complex empirical mode decomposition, both in terms of visual quality and objective evaluation criteria.

Change in atmospheric mineral aerosols in response to climate: Last glacial period, preindustrial, modern, and doubled carbon dioxide climates

USGS Publications Warehouse

Mahowald, N.M.; Muhs, D.R.; Levis, S.; Rasch, P.J.; Yoshioka, M.; Zender, C.S.; Luo, C.

2006-01-01

Desert dust simulations generated by the National Center for Atmospheric Research's Community Climate System Model for the current climate are shown to be consistent with present day satellite and deposition data. The response of the dust cycle to last glacial maximum, preindustrial, modern, and doubled-carbon dioxide climates is analyzed. Only natural (non-land use related) dust sources are included in this simulation. Similar to some previous studies, dust production mainly responds to changes in the source areas from vegetation changes, not from winds or soil moisture changes alone. This model simulates a +92%, +33%, and -60% change in dust loading for the last glacial maximum, preindustrial, and doubled-carbon dioxide climate, respectively, when impacts of carbon dioxide fertilization on vegetation are included in the model. Terrestrial sediment records from the last glacial maximum compiled here indicate a large underestimate of deposition in continental regions, probably due to the lack of simulation of glaciogenic dust sources. In order to include the glaciogenic dust sources as a first approximation, we designate the location of these sources, and infer the size of the sources using an inversion method that best matches the available data. The inclusion of these inferred glaciogenic dust sources increases our dust flux in the last glacial maximum from 2.1 to 3.3 times current deposition. Copyright 2006 by the American Geophysical Union.

Load estimator (LOADEST): a FORTRAN program for estimating constituent loads in streams and rivers

USGS Publications Warehouse

Runkel, Robert L.; Crawford, Charles G.; Cohn, Timothy A.

2004-01-01

LOAD ESTimator (LOADEST) is a FORTRAN program for estimating constituent loads in streams and rivers. Given a time series of streamflow, additional data variables, and constituent concentration, LOADEST assists the user in developing a regression model for the estimation of constituent load (calibration). Explanatory variables within the regression model include various functions of streamflow, decimal time, and additional user-specified data variables. The formulated regression model then is used to estimate loads over a user-specified time interval (estimation). Mean load estimates, standard errors, and 95 percent confidence intervals are developed on a monthly and(or) seasonal basis. The calibration and estimation procedures within LOADEST are based on three statistical estimation methods. The first two methods, Adjusted Maximum Likelihood Estimation (AMLE) and Maximum Likelihood Estimation (MLE), are appropriate when the calibration model errors (residuals) are normally distributed. Of the two, AMLE is the method of choice when the calibration data set (time series of streamflow, additional data variables, and concentration) contains censored data. The third method, Least Absolute Deviation (LAD), is an alternative to maximum likelihood estimation when the residuals are not normally distributed. LOADEST output includes diagnostic tests and warnings to assist the user in determining the appropriate estimation method and in interpreting the estimated loads. This report describes the development and application of LOADEST. Sections of the report describe estimation theory, input/output specifications, sample applications, and installation instructions.

Dissolution of first unions in Colombia, Panama, and Peru.

PubMed

Goldman, N

1981-11-01

An analysis of marital histories from World Fertility Survey data in Colombia, Panama, and Peru indicates a high level of union dissolution: the probabilities of a first union ending by separation within twenty years of the onset of union equal .27, .40, and .18 in the three countries respectively. Dissolution probabilities are especially high among women with young ages at first union and among women residing in urban areas. For all subgroups studied, consensual unions are characterized by several times the risk of separation of legal marriages. Consensual unions are especially frequent among women in rural areas, women with little education and women who enter unions at young ages. The different prevalence of consensual unions among the different subgroups affects the associations between union stability and various correlates so that it becomes essential to investigate the factors affecting union stability for both consensual unions and legal marriages. In spite of high dissolution rates, remarriage rates in all three countries are also high, as are the percentages of time spent in a union. Hence, the potential effects of voluntary disruption of unions on fertility appear to be modest.

Mycotoxins, pesticides and toxic metals in commercial spices and herbs.

PubMed

Reinholds, Ingars; Pugajeva, Iveta; Bavrins, Konstantins; Kuckovska, Galina; Bartkevics, Vadims

2017-03-01

A total of 300 samples representing six condiments (black pepper, basil, oregano, nutmeg, paprika, and thyme) were analysed for 11 mycotoxins, 134 pesticides and 4 heavy metals by ultra-high performance liquid chromatography-tandem quadrupole mass spectrometry and inductively coupled plasma mass spectrometry. Mycotoxins were detected in 4%, 10% and 30% of all nutmeg, basil and thyme samples, respectively. The residues of 24 pesticides were detected in 59% of the analysed condiments. The maximum residue levels of pesticides were exceeded in 10% of oregano and 46% of thyme samples. A risk assessment of heavy metals was performed, indicating daily intake levels far below the tolerable intake levels.

Definite Integrals, Some Involving Residue Theory Evaluated by Maple Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowman, Kimiko o

2010-01-01

The calculus of residue is applied to evaluate certain integrals in the range (-{infinity} to {infinity}) using the Maple symbolic code. These integrals are of the form {integral}{sub -{infinity}}{sup {infinity}} cos(x)/[(x{sup 2} + a{sup 2})(x{sup 2} + b{sup 2}) (x{sup 2} + c{sup 2})]dx and similar extensions. The Maple code is also applied to expressions in maximum likelihood estimator moments when sampling from the negative binomial distribution. In general the Maple code approach to the integrals gives correct answers to specified decimal places, but the symbolic result may be extremely long and complex.

The physical characteristics of match-play in English schoolboy and academy rugby union.

PubMed

Read, Dale B; Jones, Ben; Phibbs, Padraic J; Roe, Gregory A B; Darrall-Jones, Joshua; Weakley, Jonathon J S; Till, Kevin

2018-03-01

The aim was to compare the physical characteristics of under-18 academy and schoolboy rugby union competition by position (forwards and backs). Using a microsensor unit, match characteristics were recorded in 66 players. Locomotor characteristics were assessed by maximum sprint speed (MSS) and total, walking, jogging, striding and sprinting distances. The slow component (<2 m · s -1 ) of PlayerLoad TM (PL slow ), which is the accumulated accelerations from the three axes of movement, was analysed as a measure of low-speed activity (e.g., rucking). A linear mixed-model was assessed with magnitude-based inferences. Academy forwards and backs almost certainly and very likely covered greater total distance than school forwards and backs. Academy players from both positions were also very likely to cover greater jogging distances. Academy backs were very likely to accumulate greater PL slow and the academy forwards a likely greater sprinting distance than school players in their respective positions. The MSS, total, walking and sprinting distances were greater in backs (likely-almost certainly), while forwards accumulated greater PL slow (almost certainly) and jogging distance (very likely). The results suggest that academy-standard rugby better prepares players to progress to senior competition compared to schoolboy rugby.

Numerical Simulation of Shock Wave Propagation in Fractured Cortical Bone

NASA Astrophysics Data System (ADS)

Padilla, Frédéric; Cleveland, Robin

2009-04-01

Shock waves (SW) are considered a promising method to treat bone non unions, but the associated mechanisms of action are not well understood. In this study, numerical simulations are used to quantify the stresses induced by SWs in cortical bone tissue. We use a 3D FDTD code to solve the linear lossless equations that describe wave propagation in solids and fluids. A 3D model of a fractured rat femur was obtained from micro-CT data with a resolution of 32 μm. The bone was subject to a plane SW pulse with a peak positive pressure of 40 MPa and peak negative pressure of -8 MPa. During the simulations the principal tensile stress and maximum shear stress were tracked throughout the bone. It was found that the simulated stresses in a transverse plane relative to the bone axis may reach values higher than the tensile and shear strength of the bone tissue (around 50 MPa). These results suggest that the stresses induced by the SW may be large enough to initiate local micro-fractures, which may in turn trigger the start of bone healing for the case of a non union.

Screening of antibiotics and chemical analysis of penicillin residue in fresh milk and traditional dairy products in Oyo state, Nigeria

PubMed Central

Olatoye, Isaac Olufemi; Daniel, Oluwayemisi Folashade; Ishola, Sunday Ayobami

2016-01-01

Background and Aim: There are global public health and economic concerns on chemical residues in food of animal origin. The use of antibiotics in dairy cattle for the treatment of diseases such as mastitis has contributed to the presence of residues in dairy products. Penicillin residues as low as 1 ppb can lead to allergic reactions and shift of resistance patterns in microbial population as well as interfere with the processing of several dairy products. Antibiotic monitoring is an essential quality control measure in safe milk production. This study was aimed at determining antibiotic residue contamination and the level of penicillin in dairy products from Fulani cattle herds in Oyo State. Materials and Methods: The presence of antibiotic residues in 328 samples of fresh milk, 180 local cheese (wara), and 90 fermented milk (nono) from Southwest, Nigeria were determined using Premi® test kit (R-Biopharm AG, Germany) followed by high-performance liquid chromatography analysis of penicillin-G residue. Results: Antibiotic residues were obtained in 40.8%, 24.4% and 62.3% fresh milk, wara and nono, respectively. Penicillin-G residue was also detected in 41.1% fresh milk, 40.2% nono and 24.4% wara at mean concentrations of 15.22±0.61, 8.24±0.50 and 7.6±0.60 μg/L with 39.3%, 36.7% and 21.1%, respectively, containing penicillin residue above recommended Codex maximum residue limit (MRL) of 5 μg/L in dairy. There was no significant difference between the mean penicillin residues in all the dairy products in this study. Conclusion: The results are of food safety concern since the bulk of the samples and substantial quantities of dairy products in Oyo state contained violative levels of antibiotic residues including penicillin residues in concentrations above the MRL. This could be due to indiscriminate and unregulated administration of antibiotics to dairy cattle. Regulatory control of antibiotic use, rapid screening of milk and dairy farmers’ extension education on alternatives to antibiotic prophylaxis, veterinary prescriptions and withdrawal periods are recommended to prevent residues. PMID:27733794

Genetic and phenotypic parameter estimates for feed intake and other traits in growing beef cattle

USDA-ARS?s Scientific Manuscript database

Genetic parameters for dry matter intake (DMI), residual feed intake (RFI), average daily gain (ADG), mid-period body weight (MBW), gain to feed ratio (G:F) and flight speed (FS) were estimated using 1165 steers from a mixed-breed population using restricted maximum likelihood methodology applied to...

Characteristics and interrelation of recovery stress and recovery strain of an ultrafine-grained Ni-50.2Ti alloy processed by high-ratio differential speed rolling

NASA Astrophysics Data System (ADS)

Lim, Y. G.; Kim, W. J.

2017-03-01

The characteristics of the recovery stress and strain of an ultrafine-grained Ni-50.2 at% Ti alloy prepared by high-ratio differential speed rolling (HRDSR) were examined, and the factors that influence the recovery stress and strain and the relation between the two were studied. After HRDSR, both the recovery stress and strain were enhanced compared to the initial condition. The subsequent annealing treatment at 673 K, however, reduced the shape recovery properties. The constitutive equation showing that the maximum recovery stress is a sole function of the recovery strain was developed. The recovery strain increased as the yield stress increased. Thus, the maximum recovery stress increased with an increase in yield stress. The recovery stress measured at room temperature (i.e., residual recovery stress) was, on the other hand, affected by the yield stress as well as the austenite-to-martensite transformation temperature. As the yield stress increased and as the martensitic transformation temperature decreased, the residual recovery stress increased.

Estimation of maximum tolerated dose for long-term bioassays from acute lethal dose and structure by QSAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gombar, V.K.; Enslein, K.; Hart, J.B.

1991-09-01

A quantitative structure-activity relationship (QSAR) model has been developed to estimate maximum tolerated doses (MTD) from structural features of chemicals and the corresponding oral acute lethal doses (LD50) as determined in male rats. The model is based on a set of 269 diverse chemicals which have been tested under the National Cancer Institute/National Toxicology Program (NCI/NTP) protocols. The rat oral LD50 value was the strongest predictor. Additionally, 22 structural descriptors comprising nine substructural MOLSTAC(c) keys, three molecular connectivity indices, and sigma charges on 10 molecular fragments were identified as endpoint predictors. The model explains 76% of the variance and ismore » significant (F = 35.7) at p less than 0.0001 with a standard error of the estimate of 0.40 in the log (1/mol) units used in Hansch-type equations. Cross-validation showed that the difference between the average deleted residual square (0.179) and the model residual square (0.160) was not significant (t = 0.98).« less

Thermal stability and degradation kinetics of kenaf/sol-gel silica hybrid

NASA Astrophysics Data System (ADS)

Yusof, F. A. M.; Hashim, A. S.; Tajudin, Z.

2017-12-01

Thermal stability and degradation kinetics of kenaf/sol-gel silica hybrid materials was investigated by thermogravimetric analysis (TGA). Model-free iso-conversion Flynn-Wall-Ozawa (FWO) and Coats-Redfern-modified (CRm) were chosen to evaluate the activation energy of the kenaf (KF) and kenaf/sol-gel silica (KFS) at heating rates (β) of 10, 20, 30 and 40 °C/min. The results shows that an apparent activation energy was increased for the kenaf/sol-gel silica hybrid (211.59 kJ/mol for FWO and 191.55 kJ/mol for CRm) as compared to kenaf fiber (202.84 kJ/mol for FWO and 186.20 kJ/mol for CRm). Other parameters such as integral procedure decomposition temperature (IPDT), final residual weight (Rf), temperature of maximum degradation rate (Tmax) and residual at maximum temperature (RTmax) were obtained from TGA curves, additionally confirmed the thermal stability of the kenaf/sol-gel silica hybrid. These activation energy values and other findings developed the simplified approach in order to understand the thermal stability and degradation kinetics behavior of kenaf/sol-gel silica hybrid materials.

γ-PGA and MTGase improve the formation of ε-(γ-glutamyl) lysine cross-links within hairtail (Trichiurus haumela) surimi protein.

PubMed

Hu, Yaqin; Shao, Ying; Wu, Chunhua; Yuan, Chunhong; Ishimura, Gakushi; Liu, Wenjuan; Chen, Shiguo

2018-03-01

The present study investigated the mechanism of ε-(γ-glutamyl) lysine cross-links within hairtail (Trichiurus haumela) surimi protein via γ-polyglutamic acid (γ-PGA) and MTGase. The results indicated that the addition of MTGase and γ-PGA markedly improved the gelation properties of hairtail surimi protein, including its maximum breaking force and deformation, water holding capacity and gel strength. The maximum improvements were achieved by adding 0.5units MTGase/g meat paste in combination with 0.06% γ-PGA. SDS-PAGE showed that the band intensity of cross-linked proteins increased, whereas that of myosin heavy chain decreased after treatments. Further scanning electron microscopy (SEM) analysis showed the formation of a denser gel matrix, which was caused by much stronger and more inter- and intra-molecular cross-linking of proteins, via MTGase catalysing ε-(γ-glutamyl) lysine cross-links formed between lysine residues in the gel protein and glutamic residues in the hydrolytic γ-PGA. The results provide reliable guidance for the improvement of hairtail surimi protein gelation properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Validation of a liquid chromatography-electrospray ionization tandem mass spectrometric method to determine six polyether ionophores in raw, UHT, pasteurized and powdered milk.

PubMed

Pereira, Mararlene Ulberg; Spisso, Bernardete Ferraz; Jacob, Silvana do Couto; Monteiro, Mychelle Alves; Ferreira, Rosana Gomes; Carlos, Betânia de Souza; da Nóbrega, Armi Wanderley

2016-04-01

This study aimed to validate a method developed for the determination of six antibiotics from the polyether ionophore class (lasalocid, maduramicin, monensin, narasin, salinomycin and semduramicin) at residue levels in raw, UHT, pasteurized and powdered milk using QuEChERS extraction and high performance liquid chromatography coupled to tandem mass spectrometry (HPLC-MS/MS). The validation was conducted under an in-house laboratory protocol that is primarily based on 2002/657/EC Decision, but takes in account the variability of matrix sources. Overall recoveries between 93% and 113% with relative standard deviations up to 16% were obtained under intermediate precision conditions. CCα calculated values did not exceed 20% the Maximum Residue Limit for monensin and 25% the Maximum Levels for all other substances. The method showed to be simple, fast and suitable for verifying the compliance of raw and processed milk samples regarding the limits recommended by Codex Alimentarius and those adopted in European Community for polyether ionophores. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biomass fast pyrolysis for bio-oil production in a fluidized bed reactor under hot flue atmosphere.

PubMed

Li, Ning; Wang, Xiang; Bai, Xueyuan; Li, Zhihe; Zhang, Ying

2015-10-01

Fast pyrolysis experiments of corn stalk were performed to investigate the optimal pyrolysis conditions of temperature and bed material for maximum bio-oil production under flue gas atmosphere. Under the optimized pyrolysis conditions, furfural residue, xylose residue and kelp seaweed were pyrolyzed to examine their yield distributions of products, and the physical characteristics of bio-oil were studied. The best flow rate of the flue gas at selected temperature is obtained, and the pyrolysis temperature at 500 degrees C and dolomite as bed material could give a maximum bio-oil yield. The highest bio-oil yield of 43.3% (W/W) was achieved from corn stalk under the optimal conditions. Two main fractions were recovered from the stratified bio-oils: light oils and heavy oils. The physical properties of heavy oils from all feedstocks varied little. The calorific values of heavy oils were much higher than that of light oils. The pyrolysis gas could be used as a gaseous fuel due to a relatively high calorific value of 6.5-8.5 MJ/m3.

Removal of fluoride, arsenic and coliform bacteria by modified homemade filter media from drinking water.

PubMed

Devi, Rani; Alemayehu, Esayas; Singh, Vijender; Kumar, Ashok; Mengistie, Embialle

2008-05-01

An attempt was made to investigate the removal of fluoride, arsenic and coliform bacteria from drinking water using modified homemade filter media. Batch mode experimental study was conducted to test the efficiency of modified homemade filter for reduction of impurities under the operating condition of treatment time. The physico-chemical and biological analysis of water samples had been done before and after the treatment with filter media, using standard methods. Optimum operating treatment time was determined for maximum removal of these impurities by running the experiment for 2, 4, 6, 8, 10 and 12h, respectively. The maximum reduction of fluoride, arsenic and coliform bacteria in percentage was 85.60%, 93.07% and 100% and their residual values were 0.72 mg/l, 0.009 mg/l and 0 coliform cells/100ml, respectively after a treatment time of 10h. These residual values were under the permissible limits prescribed by WHO. Hence this could be a cheap, easy and an efficient technique for removal of fluoride, arsenic and coliform bacteria from drinking water.