High temperature process steam application at the Southern Union Refining Company, Hobbs, New Mexico. Solar energy in the oil patch. Final report, Phase III: operation, maintenance, and performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, L.E.; McGuire, D.R.

1984-05-01

This final report summarizes the technical reports for Phase III of this project. The third phase included the operation, maintenance, upgrade and performance reporting of a 10,080 square foot Solar Industrial Process Heat System installed at the Famariss Energy Refinery of Southern Union Refining Company near Hobbs, New Mexico. This report contains a description of the upgraded system, and a summary of the overall operation, maintenance and performance of the installed system. The results of the upgrade activities can be seen in the last two months of operational data. Steam production was significantly greater in peak flow and monthly totalmore » than at any previous time. Also monthly total cost savings was greatly improved even though natural gas costs remain much lower than originally anticipated.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silver, M.

The decision in Union Petroleum Corp. v. United States reaffirms the Federal judiciary's commitment to control water pollution under the Federal Water Pollution Control Act. Those in charge of oil terminals who have taken reasonable precautions to prevent vandalism and oil spills into navigable rivers will be reimbursed when vandals spill oil from tank cars parked at the terminal. Awarding Union the full $99,952.17 encourages other terminal operators to quickly clean up harmful discharges into the nation's waters. The court implicitly recognized that the general security practice in the industry is a reasonable standard of care. Though the standard toleratesmore » some danger of discharge of harmful substances, this level of industry risk remains unchanged by the decision of the Court of Claims. 12 references.« less

Fulbrights for Soviet Lectures

NASA Astrophysics Data System (ADS)

Packard, Craig

The Council for International Exchange of Scholars is still accepting applications for Fulbright awards to lecture in the sciences in the Soviet Union for academic year 1989-1990. Because the original deadline, September 15, has passed, applications will be processed immediately, and the 1989-1990 Fulbright Scholar Program Faculty Grants close when an adequate number of applicants is approved for nomination.Applications can be in the “Any Field” category or in the more specific categories sought by the Soviet Union, including geophysics at Tashkent; geology at the Gubkin Institute of Oil, Chemical, and Gas Industry; environmental sciences (cultivation of microalgae in sewage; continental shelf development, water resources protection, and economic aspects); and forest restoration technology. Awards are also available in chemistry, life sciences, and physics and astronomy.

Chapter 5: Geologic Assessment of Undiscovered Petroleum Resources in the Waltman Shale Total Petroleum System,Wind River Basin Province, Wyoming

USGS Publications Warehouse

Roberts, Steve B.; Roberts, Laura N.R.; Cook, Troy

2007-01-01

The Waltman Shale Total Petroleum System encompasses about 3,400 square miles in the Wind River Basin Province, Wyoming, and includes accumulations of oil and associated gas that were generated and expelled from oil-prone, lacustrine shale source rocks in the Waltman Shale Member of the Paleocene Fort Union Formation. Much of the petroleum migrated and accumulated in marginal lacustrine (deltaic) and fluvial sandstone reservoirs in the Shotgun Member of the Fort Union, which overlies and intertongues with the Waltman Shale Member. Additional petroleum accumulations derived from Waltman source rocks are present in fluvial deposits in the Eocene Wind River Formation overlying the Shotgun Member, and also might be present within fan-delta deposits included in the Waltman Shale Member, and in fluvial sandstone reservoirs in the uppermost part of the lower member of the Fort Union Formation immediately underlying the Waltman. To date, cumulative production from 53 wells producing Waltman-sourced petroleum exceeds 2.8 million barrels of oil and 5.8 billion cubic feet of gas. Productive horizons range from about 1,770 feet to 5,800 feet in depth, and average about 3,400 to 3,500 feet in depth. Formations in the Waltman Shale Total Petroleum System (Fort Union and Wind River Formations) reflect synorogenic deposition closely related to Laramide structural development of the Wind River Basin. In much of the basin, the Fort Union Formation is divided into three members (ascending order): the lower unnamed member, the Waltman Shale Member, and the Shotgun Member. These members record the transition from deposition in dominantly fluvial, floodplain, and mire environments in the early Paleocene (lower member) to a depositional setting characterized by substantial lacustrine development (Waltman Shale Member) and contemporaneous fluvial, and marginal lacustrine (deltaic) deposition (Shotgun Member) during the middle and late Paleocene. Waltman Shale Member source rocks have total organic carbon values ranging from 0.93 to 6.21 weight percent, averaging about 2.71 weight percent. The hydrocarbon generative potential of the source rocks typically exceeds 2.5 milligrams of hydrocarbon per gram of rock and numerous samples had generative potentials exceeding 6.0 milligrams of hydrocarbon per gram of rock. Waltman source rocks are oil prone, and contain a mix of Type-II and Type-III kerogen, indicating organic input from a mix of algal and terrestrial plant matter, or a mix of algal and reworked or recycled material. Thermal maturity at the base of the Waltman Shale Member ranges from a vitrinite reflectance value of less than 0.60 percent along the south basin margin to projected values exceeding 1.10 percent in the deep basin west of Madden anticline. Burial history reconstructions for three wells in the northern part of the Wind River Basin indicate that the Waltman Shale Member was well within the oil window (Ro equal to or greater than 0.65 percent) by the time of maximum burial about 15 million years ago; maximum burial depths exceeded 10,000 feet. Onset of oil generation calculated for the base of the Waltman Shale member took place from about 49 million years ago to about 20 million years ago. Peak oil generation occurred from about 31 million years ago to 26 million years ago in the deep basin west of Madden anticline. Two assessment units were defined in the Waltman Shale Total Petroleum System: the Upper Fort Union Sandstones Conventional Oil and Gas Assessment Unit (50350301) and the Waltman Fractured Shale Continuous Oil Assessment Unit (50350361). The conventional assessment unit primarily relates to the potential for undiscovered petroleum accumulations that are derived from source rocks in the Waltman Shale Member and trapped within sandstone reservoirs in the Shotgun Member (Fort Union Formation) and in the lower part of the overlying Wind River Formation. The potential for Waltman-sourced oil accumulations in fan-delta depos

Chapter 4: The Cretaceous-Lower Tertiary Composite Total Petroleum System, Wind River Basin, Wyoming

USGS Publications Warehouse

Johnson, R.C.; Finn, Thomas M.; Kirschbaum, Mark A.; Roberts, Stephen B.; Roberts, Laura N.R.; Cook, Troy; Taylor, David J.

2007-01-01

The Cretaceous-Lower Tertiary Composite Total Petroleum System (TPS) of the Wind River Basin Province includes all strata from the base of the Lower Cretaceous Cloverly Formation to the base of the Waltman Shale Member of the Paleocene age Fort Union Formation and, where the Waltman is absent, includes strata as young as the Eocene Wind River Formation. Locally, Cretaceous-sourced gas migrated into strata as old as the Mississippian Madison Limestone, and in these areas the TPS extends stratigraphically downward to include these reservoirs. The extensive vertical migration of gases in highly fractured areas of the Wind River Basin led to the commingling of gases from several Upper Cretaceous and lower Tertiary sources, thus only two petroleum systems are recognized in these rocks, the Cretaceous-Lower Tertiary Composite TPS, the subject of this report, and the Waltman Shale TPS described by Roberts and others (Chapter 5, this CD-ROM). The Cretaceous-lower Tertiary Composite TPS was subdivided into (1) seven continuous gas assessment units (AU): (a) Frontier-Muddy Continuous Gas AU, (b) Cody Sandstone Continuous Gas AU, (c) Mesaverde--Meeteetse Sandstone Gas AU, (d) Lance-Fort Union Sandstone Gas AU, (e) Mesaverde Coalbed Gas AU, (f) Meeteetse Coalbed Gas AU, and (g) Fort Union Coalbed Gas AU; (2) one continuous oil assessement unit--- Cody Fractured Shale Continuous Oil AU; and (3) one conventional assessment Unit--- Cretaceous-Tertiary Conventional Oil and Gas AU. Estimates of undiscovered resources having the potential for additions to reserves were made for all but the Cody Fractured Shale Continuous Oil AU, which is considered hypothetical and was not quantitively assessed. The mean estimate of the total oil is 41.99 million barrels, mean estimate of gas is 2.39 trillion cubic feet, and mean estimate of natural gas liquids is 20.55 million barrels. For gas, 480.66 billion cubic feet (BCFG) is estimated for the Frontier-Muddy Continuous Gas AU, 115.34 BCFG for the Cody Sandstone Continuous Gas AU, 383.16 BCFG for the Mesaverde-Meeteetse Sandstone Continuous Gas AU, 711.30 BCFG for the Lance-Fort Union Sandstone Gas AU, 107.18 BCFG for the Mesaverde Coalbed Gas AU, 21.29 BCFG for the Meeteetse Coalbed Gas AU, and 118.08 BCFG for the Fort Union Coalbed Gas AU. All the undiscovered oil and 98.94 BCFG of undiscovered gas is in the Cretaceous-Tertiary Conventional Oil and Gas AU.

12. Photocopy of oil painting, LOOKING UP BROAD STREET FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. Photocopy of oil painting, LOOKING UP BROAD STREET FROM THE STONE BRIDGE, 1795 and after (from Historical Collection of the State of New Jersey) - South Broad Street Bridge, Spanning Elizabeth River, Elizabeth, Union County, NJ

11. Photocopy of oil painting, LOOKING UP BROAD STREET FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Photocopy of oil painting, LOOKING UP BROAD STREET FROM THE STONE BRIDGE, 1795 and after (from Historical Collection of the State of New Jersey) - South Broad Street Bridge, Spanning Elizabeth River, Elizabeth, Union County, NJ

Fuels from Recycling Systems

ERIC Educational Resources Information Center

Tillman, David A.

1975-01-01

Three systems, operating at sufficient scale, produce fuels that may be alternatives to oil and gas. These three recycling systems are: Black Clawson Fiberclaim, Franklin, Ohio; Union Carbide, South Charleston, West Virginia; and Union Electric, St. Louis, Missouri. These produce a wet fuel, a pyrolytic gas, and a dry fuel, respectively. (BT)

INTERIOR OF BOILER BUILDING, FIRST LEVEL, EAST SIDE, SHOWING STEAMDRIVEN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR OF BOILER BUILDING, FIRST LEVEL, EAST SIDE, SHOWING STEAM-DRIVEN PISTON PUMPS FOR FUEL OIL, CAMERA FACING EAST. - New Haven Rail Yard, Central Steam Plant and Oil Storage, Vicinity of Union Avenue, New Haven, New Haven County, CT

1984 CRC (Coordinating Research Council, Inc.) Octane Number Requirement Rating Workshop.

DTIC Science & Technology

1985-06-01

Richard J . Tither Mobil Oil Corporation Sam D. Vallas Amoco Oil Company Douglas A. Voss Chevron Research Company Andy Vukovic Shell Canada Dave G...Instrumentation, * Preparation a Test Fuels: Procurement of Fuels and Cans, and Coordina- tion of On-Site Handling e Data Handling and Analysis j 2 nI |S 0- B-2 V...Doug McCorkell Union Oil Company of California James D. Merritt Amoco Oil Company Michael J . Mlotkowski Mobil Oil Corporation John Pandosh Sun Tech

Market Potential of Downtown Cheyenne

DTIC Science & Technology

1985-02-01

utility companies and 4 oil and gas related concerns. These tax payers are summarized below. CITY OF CHEYENNE, WYOMING PRINCIPAL TAXPAYERS June 30...Husky Oil Co. Refinery 9,429,011 6.61% Union Pacific Railroad 8,036,532 5.64% Amoco Oil and Gas 4,967,542 3.48% 0 Wycon Chemical Co. Chemical...2,603,583 1.83% Mobil Oil Oil and Gas 1,965,632 1.38% Burlington Northern Railroad 1,483,681 1.04% $58,028,897 40.71% Source: Laramie County Tax

Teaching about Energy Issues and Energy Independence Using the Internet

ERIC Educational Resources Information Center

Risinger, C. Frederick

2006-01-01

Energy issues have moved up the public agenda in recent decades, and were highlighted in President Bush's State of the Union address when he declared, "America is addicted to oil...." and pledging to "replace more than 75 percent of oil imports from the Middle East by 2025." The author observes that oil dependence and energy independence will be…

North Korea Country Analysis Brief

EIA Publications

2015-01-01

North Korea was once the industrial heartland of the Korean peninsula. Following the dissolution of the former Soviet Union in 1992, North Korea lost its major trading partner. North Korea's economy was unable to adapt, and its economy soon deteriorated. Without subsidized oil from the Soviet Union and China, North Korea was unable to meet its energy demand.

Thriving public-private partnership to fortify cooking oil in the West African Economic and Monetary Union (UEMOA) to control vitamin A deficiency: Faire Tache d'Huile en Afrique de l'Ouest.

PubMed

Sablah, Mawuli; Klopp, Jennifer; Steinberg, Douglas; Touaoro, Zaoro; Laillou, Arnaud; Baker, Shawn

2012-12-01

In sub-Saharan Africa, more than 42% of children are at risk for vitamin A deficiency, and control of vitamin A deficiency will prevent more than 600,000 child deaths annually. In the West African Economic and Monetary Union (UEMOA), an estimated 54.3% of preschool-age children are vitamin A deficient and 13% of pregnant women have night blindness. To project the achievements of this West African coalition. This article documents the achievements, challenges, and lessons learned associated with the development of a public-private partnership to fortify vegetable oil in West Africa through project reports and industry assessments. National-level food consumption surveys identified cooking oil as a key vehicle for vitamin A. Stakeholders therefore advocated for the production of fortified vegetable oil at large scale, supported industrial assessments, and reinforced the capacity of cooking oil industries to implement vitamin A fortification through effective coordination of public and private partnerships tied with standards, regulations, and social marketing. Strong alliances for food fortification were established at the regional and national levels. Stakeholders also developed policies, adopted directives, built capacity, implemented social marketing, and monitored quality enforcement systems to sustain fortification for maximum public health impact. The synergy created resulted from the unique and complementary core competencies of all the partners under effective coordination. The initiative began with the 8 UEMOA member countries and now includes all 15 countries of the Economic Community of West African States (ECOWAS), plus Cameroon, Tanzania, and Mozambique, forming a sub-Saharan Africa-wide initiative on food fortification. All members of the Professional Association of Cooking Oil Industries of the West African Economic and Monetary Union (AIFO-UEMOA) now fortify edible oil with vitamin A. Through multisector cooperation, an estimated 70% of the population has access to vitamin A-fortified edible oil in participating countries. Sustainable fortification of cooking oil is now a reality in all UEMOA countries.

Formulation of US international energy policies

NASA Astrophysics Data System (ADS)

1980-09-01

To find out how the United States develops international energy policy, GAO reviewed five major energy issues covering the period from early 1977 through 1979. The issues are: vulnerabilities to petroleum supply interruptions; long term national security strategy on imported oil prices; export of U.S. oil and gas production equipment and technology to the Soviety Union; World Bank initiatives to assist in financing oil and gas exploration and development in oil-importing developing countries; and the role of gas imports relative to the nation's future sources of gas.

The impact of fruit maturation on bioactive microconstituents, inhibition of serum oxidation and inflammatory markers in stimulated PBMCs and sensory characteristics of Koroneiki virgin olive oils from Messenia, Greece.

PubMed

Kaliora, Andriana C; Artemiou, Anna; Giogios, Ioannis; Kalogeropoulos, Nick

2013-08-01

Olive fruits from the Koroneiki cultivar (Olea europaea L.) grown in Messenia, Greece, were hand-picked from the same trees in progressive maturity stages, covering three months, and processed identically with a commercial olive mill and a three-phase decanter. Data on quality parameters, and antioxidant activity of the obtained oils were collected by employing the conventional analytical methods set by European Union Commission Regulation no. 61/2011. Additionally, the potential of oils' polar extract to inhibit total serum lipid oxidation and inflammatory markers in stimulated human mononuclear cells was assayed. The results showed that ripening caused an increase in monounsaturated and decrease in polyunsaturated fatty acids, as well as an increase in phenolic compounds - mainly hydroxytyrosol - and in squalene. The extracts' ferric reducing power was in line with the increase of phenolic compounds. In later stages of maturation, lipoprotein oxidation was less potent and the decrease of inflammatory markers in stimulated human mononuclear cells was more powerful. Sensory evaluation detected differences in oils' "bitter" attributes, while the analysis of oils' volatiles revealed quantitative differences.

[Analisys of work-related accidents and incidents in an oil refinery in Rio de Janeiro].

PubMed

de Souza, Carlos Augusto Vaz; de Freitas, Carlos Machado

2003-01-01

Accidents in the chemical industry can have serious consequences for workers, communities, and the environment and are thus highly relevant to public health. This article is the result of an occupational surveillance project involving several public institutions. We analyze 800 work-related accidents that resulted in injuries, environmental damage, or loss of production in 1997 in an oil refinery located in Rio de Janeiro, Brazil. The methodology was based on managerial and organizational approaches to accident investigation, with the European Union reporting system as the reference. The results highlight various limitations in the process of reporting and investigating accidents, as well as a certain hierarchy of accidents, with more attention given to accidents involving loss of production and less to those resulting in injuries, particularly among outsourced workers.

Skilling Australia for the Future? A Study of Quality Assurance in Australia's Vocational Education and Training

ERIC Educational Resources Information Center

Agbola, Frank Wogbe; Lambert, Daniel Kenneth

2010-01-01

From the end of World War II until the early 1970s, vocational education and training (VET) in Australia was surprisingly static and resilient to government-led reform, due to the dominance of industry and union power. Following the oil shocks of 1973 and associated unemployment and declining union power, there have been calls on the federal and…

Soviet business chaos seen lasting 5 years

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-16

This paper reports that companies seeking work in the collapsing Soviet Union can expect political uncertainty for another 5 years. PW discussed changes in the Soviet Union and offered advice on dealing with officials of the central government and Soviet republics at a recent meeting in Houston with executives of oil field service companies. That meeting preceded reports of the Russian federation, Ukraine, and Byelorussia agreeing to form a Slavic commonwealth.

Initial Investigation into the Potential of CSP Industrial Process Heat for the Southwest United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurup, Parthiv; Turchi, Craig

2015-11-01

After significant interest in the 1970s, but relatively few deployments, the use of solar technologies for thermal applications, including enhanced oil recovery (EOR), desalination, and industrial process heat (IPH), is again receiving global interest. In particular, the European Union (EU) has been a leader in the use, development, deployment, and tracking of Solar Industrial Process Heat (SIPH) plants. The objective of this study is to ascertain U.S. market potential of IPH for concentrating collector technologies that have been developed and promoted through the U.S. Department of Energy's Concentrating Solar Power (CSP) Program. For this study, the solar-thermal collector technologies ofmore » interest are parabolic trough collectors (PTCs) and linear Fresnel (LF) systems.« less

Union Texas hopes to reproduce its Pakistan Badin experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petzet, G.A.

1997-11-03

Union Texas Petroleum Holdings Inc. has resolved to transplant elsewhere in the world the success of tis 20 year old grass-roots exploration effort on the Badin block in Pakistan. Union Texas Pakistan Inc. (UTP) is actively seeking exploration concessions in Pakistan, and the parent company is on an international bent aimed at finding other areas where it might reproduce its performance in Pakistan. The 104 exploratory wells drilled through April 1, 1997, resulted in 47 discoveries and 57 dry holes for a 45% success rate. Some oil and gas are produced from the Middle Sand units, and some gas ismore » produced from the Basal Sand units. The 1997 Badin exploration plan called for 11 exploratory wells, including one, Tarai Deep-3, that would test a new play concept in Jurassic Chiltan. It also called for Badin`s first 3D seismic surveys, at South Buzdar and Tangri fields on the northern part of the block, and 146 km of 2D seismic acquisition. The paper discusses Badin development, drilling status, operating challenges, oil price and sales, gas markets, local effects, and future developments.« less

Trust in training: the Oil, Chemical, and Atomic Workers International Union Worker-to-Worker Training Program.

PubMed

Merrill, M

1994-01-01

The OCAW's Worker-to-Worker Training Program was established with one of the first grants awarded under the Superfund Amendments and Reauthorization Act of 1986. The union intended the program to serve as a model to industry and to raise the standard of safety and health training throughout the industry. The program, which requires trainees to actively participate in learning activities, has garnered praise from its participants.

JPRS Report, Soviet Union KOMMUNIST No 12, August 1988.

DTIC Science & Technology

1988-12-28

use in joint enterprises technology for the production of sour milk products, starch, volatile oils, citric acid , sparkling and fruit-berry wines...to labor conditions and intensiveness, in this case the trade union cannot remain a passive observer. In other words, the solution of many...made in the past as well. The 27th Party Congress weakened this view, but not in everyone’s mind. There are those who still believe that all of these

The use of underwater high-voltage discharges to improve the efficiency of Jatropha curcas L. biodiesel production.

PubMed

Maroušek, Josef; Itoh, Shigeru; Higa, Osamu; Kondo, Yoshikazu; Ueno, Masami; Suwa, Ryuichi; Komiya, Yasuaki; Tominaga, Jun; Kawamitsu, Yoshinobu

2012-01-01

Underwater high-voltage discharges (3.5 kV) resulting in 4.9 kJ shock waves (50-60 MPa) were studied at the laboratory scale as a Jatropha curcas L. seed disintegration method. Grinding and macerating in an excess of methanol (3.5:1) was advantageous because methanol acts both as a liquid carrier for the pressure shock waves and as a solvent that increases the efficiency of oil extraction while remaining usable for esterification. The influence of the number of shock waves and the intensity of methanol maceration on the heat values of the pressed cake are stated in detail. Soxhlet extraction demonstrated that a greater than 94% oil extraction was achieved. The increased disintegration of vacuoles rich in oil was documented by surface area analysis, mineralization kinetics analysis, and electron microscopy. The working volumes were small, and the proportion of energy inadequate compared to the yields released; however, much can be improved by upgrading the process. © 2012 International Union of Biochemistry and Molecular Biology, Inc.

Viet Nam, once isolated, poised for significant role in oil and gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-07-15

This paper reports that Viet Nam is on its way up in the petroleum world. After years of international isolation, the country is poised for a flurry of exploration by international oil companies in the early 1990s. Viet Nam has joined the Soviet Union as the only members of the now dissolved, formerly Moscow dominated, 10 nation Council for Mutual Economic Assistance (CMEA) that are self-sufficient in oil production. Moreover, Viet Nam has far outstripped neighboring China, which was not a CMEA member, in offshore oil flow even though China has a much larger Outer Continental Shelf. Prospects are thatmore » Viet Nam will continue to lead China in offshore oil production until 1995 at least.« less

Publications - GMC 244 | Alaska Division of Geological & Geophysical

Science.gov Websites

Ridge Unit #1 well Authors: DGSI, Inc. Publication Date: 1995 Publisher: Alaska Division of Geological Union Oil Company of California Trail Ridge Unit #1 well: Alaska Division of Geological &

Burial history, thermal maturity, and oil and gas generation history of petroleum systems in the Wind River Basin Province, central Wyoming: Chapter 6 in Petroleum systems and geologic assessment of oil and gas resources in the Wind River Basin Province, Wyoming

USGS Publications Warehouse

Roberts, Laura N.R.; Finn, Thomas M.; Lewan, Michael D.; Kirschbaum, Mark A.

2007-01-01

Burial history, thermal maturity, and timing of oil and gas generation were modeled for eight key source rock units at nine well locations throughout the Wind River Basin Province. Petroleum source rocks include the Permian Phosphoria Formation, the Cretaceous Mowry Shale, Cody Shale, and Mesaverde, Meeteetse, and Lance Formations, and the Tertiary (Paleocene) Fort Union Formation, including the Waltman Shale Member. Within the province boundary, the Phosphoria is thin and only locally rich in organic carbon. Phosphoria oil produced from reservoirs in the province is thought to have migrated from the Wyoming and Idaho thrust belt. Locations (wells) selected for burial history reconstructions include three in the deepest parts of the province (Adams OAB-17, Bighorn 1-5, and Coastal Owl Creek); three at intermediate depths (Hells Half Acre, Shell 33X-10, and West Poison Spider); and three at relatively shallow locations (Young Ranch, Amoco Unit 100, and Conoco-Coal Bank). The thermal maturity of source rocks is greatest in the deep northern and central parts of the province and decreases to the south and east toward the basin margins. The results of the modeling indicate that, in the deepest areas, (1) peak petroleum generation from Cretaceous rocks occurred from Late Cretaceous through middle Eocene time, and (2) onset of oil generation from the Waltman Shale Member occurred from late Eocene to early Miocene time. Based on modeling results, gas generation from the cracking of Phosphoria oil reservoired in the Park City Formation reached a peak in the late Paleocene/early Eocene (58 to 55 Ma) only in the deepest parts of the province. The Mowry Shale and Cody Shale (in the eastern half of the basin) contain a mix of Type-II and Type-III kerogens. Oil generation from predominantly Type-II source rocks of these units in the deepest parts of the province reached peak rates during the latest Cretaceous to early Eocene (65 to 55 Ma). Only in these areas of the basin did these units reach peak gas generation from the cracking of oil, which occurred in the early to middle Eocene (55 to 42 Ma). Gas-prone source rocks of the Mowry and Cody Shales (predominantly Type-III kerogen), and the Mesaverde, Meeteetse, Lance, and Fort Union Formations (Type –III kerogen) reached peak gas generation in the latest Cretaceous to late Eocene (67 to 38 Ma) in the deepest parts of the province. Gas generation from the Mesaverde source rocks started at all of the modeled locations but reached peak generation at only the deepest locations and at the Hells Half Acre location in the middle Paleocene to early Eocene (59 to 48 Ma). Also at the deepest locations, peak gas generation occurred from the late Paleocene to the early Eocene (57 to 49 Ma) for the Meeteetse Formation, and during the Eocene for the Lance Formation (55 to 48 Ma) and the Fort Union Formation (44 to 38 Ma). The Waltman Shale Member of the Fort Union Formation contains Type-II kerogen. The base of the Waltman reached a level of thermal maturity to generate oil only at the deep-basin locations (Adams OAB-17 and Bighorn 1-5 locations) in the middle Eocene to early Miocene (36 to 20 Ma).

Petroleum - politics and power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brossard, E.B.

1983-01-01

Governments all over the world are politically maneuvering themselves into positions where they can use this precious resource as a tool to gain power. Notes the author, ''Even the largest oil company can be powerless against the smallest government.'' This thesis is the foundation of Brossard's investigation of the international oil industry and the power and politics that are involved in the struggle for dominance. Contents: The petroleum age; The Russian nobles and the Soviet Union; The Majors - big oil; The complex operations of the oil industry; U.S. government controls; Natural gas - the most efficient fuel; The Organizationmore » of Petroleum Exporting Countries; OPEC and the international market; Canadian petroleum; Alaska - the hope of the Lower 48.« less

JPRS Report, Soviet Union, Political Affairs.

DTIC Science & Technology

1988-11-10

Kennedy’s visit to West Berlin had poured oil into the fire but realistic politicians knew that there were no reasons for interference. International...Semper and Neeme Ruus. In July-August 1940 eight of 11 ministers became members of the Estonian Communist Party. Decrees appointing proponents of...villages of Old Believers. We also poured a lot of oil into the flames after Lithua- nia’s liberation from the German fascists. Intimitated by those

JPRS Report, Soviet Union, Economic Affairs

DTIC Science & Technology

1988-08-18

nonreproducible and their depletion dur- ing the planned period can demand increasing expendi- tures on extraction or import and so forth). With such...fabrics, of oil on the production of dyes, of electric motors on the extraction and pumping of oil, of wire on electric motor winding, and so...exactly what amount should coal prices be raised and how to take into account in profit taxes extraction conditions, which even in two mines located next

Student internships with unions and workers: building the occupational health and safety movement.

PubMed

Bateson, Gail

2013-01-01

One of the most successful programs to recruit young professionals to the occupational safety and health field was launched more than 35 years ago, in 1976. Created by the Montefiore Medical Center's Department of Social Medicine collaborating with Tony Mazzocchi of the Oil, Chemical and Atomic Workers International Union (OCAW), it placed medical, nursing, and public health students in summer internships with local unions to identify and solve health and safety problems in the workplace. The experience of working with and learning from workers about the complex interactions of political, economic, and scientific-technological issues surrounding workplace conditions inspired many students to enter and stay in our field. Many former interns went on to make important medical and scientific contributions directly linked to their union-based projects. Former interns are now among the leaders within the occupational health and safety community, holding key positions in leading academic institutions and governmental agencies.

Burial History, Thermal Maturity, and Oil and Gas Generation History of Source Rocks in the Bighorn Basin, Wyoming and Montana

USGS Publications Warehouse

Roberts, Laura N.R.; Finn, Thomas M.; Lewan, Michael D.; Kirschbaum, Mark A.

2008-01-01

Burial history, thermal maturity, and timing of oil and gas generation were modeled for seven key source-rock units at eight well locations throughout the Bighorn Basin in Wyoming and Montana. Also modeled was the timing of cracking to gas of Phosphoria Formation-sourced oil in the Permian Park City Formation reservoirs at two well locations. Within the basin boundary, the Phosphoria is thin and only locally rich in organic carbon; it is thought that the Phosphoria oil produced from Park City and other reservoirs migrated from the Idaho-Wyoming thrust belt. Other petroleum source rocks include the Cretaceous Thermopolis Shale, Mowry Shale, Frontier Formation, Cody Shale, Mesaverde and Meeteetse Formations, and the Tertiary (Paleocene) Fort Union Formation. Locations (wells) selected for burial history reconstructions include three in the deepest parts of the Bighorn Basin (Emblem Bench, Red Point/Husky, and Sellers Draw), three at intermediate depths (Amoco BN 1, Santa Fe Tatman, and McCulloch Peak), and two at relatively shallow locations (Dobie Creek and Doctor Ditch). The thermal maturity of source rocks is greatest in the deep central part of the basin and decreases to the south, east, and north toward the basin margins. The Thermopolis and Mowry Shales are predominantly gas-prone source rocks, containing a mix of Type-III and Type-II kerogens. The Frontier, Cody, Mesaverde, Meeteetse, and Fort Union Formations are gas-prone source rocks containing Type-III kerogen. Modeling results indicate that in the deepest areas, (1) the onset of petroleum generation from Cretaceous rocks occurred from early Paleocene through early Eocene time, (2) peak petroleum generation from Cretaceous rocks occurred during Eocene time, and (3) onset of gas generation from the Fort Union Formation occurred during early Eocene time and peak generation occurred from late Eocene to early Miocene time. Only in the deepest part of the basin did the oil generated from the Thermopolis and Mowry Shales start generating gas from secondary cracking, which occurred in the late Eocene to Miocene. Also, based on modeling results, gas generation from the cracking of Phosphoria oil reservoired in the Park City Formation began in the late Eocene in the deep part of the basin but did not anywhere reach peak generation.

Cuba: World Oil Report 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maciej, H.

This paper reports that plagued by his worst fuel crisis in years, Cuban President Fidel Castro late last year began soliciting foreign help in the country's exploration efforts. What is particularly new about this initiative is that the invitation was directed toward capitalist Western nations, as opposed to previous help supplied by the Soviet Union. Castro's sudden change of attitude has been spurred by the continuing shortfall in oil deliveries from the USSR, symptomatic of the latter's own production problems.

75 FR 75662 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-06

..., union representatives and industry groups' to discuss regulation of offshore drilling operations in the... from leading safety experts involved in offshore drilling activities from countries including the... be holding an all day symposium entitled ``International Models of Offshore Oil Rig Regulation'' on...

San Francisco Bay to Stockton, California Project. Environmental Impact Statement. John F. Baldwin Ship Channel. Phase II. Richmond Harbor Approach.

DTIC Science & Technology

1984-05-01

of San Pablo Bay and Carquinez Strait. The maneuvering area near the Union Oil Company wharf at Oleum would be deepened to 45 feet and enlarged...Tosco) Oil Company piers at Martinez would be deepened to 45 feet. The channel would taper to approximately 300 feet wide at the Interstate 680...Inland Pilots Association, Port of Richmond, Chevron and various other shipping companies . 1.08 Peport Format. This report consists of a main report

Industry turns its attention south

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marhefka, D.

1997-08-01

The paper discusses the outlook for the gas and oil industries in the Former Soviet Union and Eastern Europe. Significant foreign investment continues to elude Russia`s oil and gas industry, so the Caspian nations of Kazakhstan and Azerbaijan are picking up the slack, welcoming the flow of foreign capital to their energy projects. Separate evaluations are given for Russia, Azerbaijan, Kazakhstan, Turkmenistan, Ukraine, Armenia, Belarus, Georgia, Lithuania, Latvia, Estonia, Moldova, Tajikstan, Uzbekistan, Albania, Bulgaria, Croatia, Czech Republic, Hungary, Poland, Romania, Slovakia, Slovenia, and Serbia.

Optimization and modeling for the synthesis of sterol esters from deodorizer distillate by lipase-catalyzed esterification.

PubMed

Zhang, Xinyu; Yu, Jiang; Zeng, Aiwu

2017-03-01

In this paper, cotton seed oil deodorizer distillate (CSODD), was recovered to obtain fatty acid sterol ester (FASE), which is one of the biological activated substances added as human therapeutic to lower cholesterol. Esterification reactions were carried out using Candida rugosa lipase as a catalyst, and the conversion of phytosterol was optimized using response surface methodology. The highest conversion (90.8 ± 0.4%) was reached at 0.84 wt% enzyme load, 1:25 solvent/CSODD mass ratio, and 44.2 °C after 12 H reaction. A kinetic model based on the reaction rate equation was developed to describe the reaction process. The activation energy of the reaction was calculated to be 56.9 kJ/mol and the derived kinetic parameters provided indispensable basics for further study. The optimization and kinetic research of synthesizing FASE from deodorizer distillate provided necessary information for the industrial applications in the near future. Experimental results showed that the proposed process is a promising alternative to recycle sterol esters from vegetable oil deodorizer distillates in a mild, efficient, and environmental friendly method. © 2016 International Union of Biochemistry and Molecular Biology, Inc.

The fellow speaks: Sometimes you get only one chance

USGS Publications Warehouse

Hsieh, Paul A.

2014-01-01

I am grateful to AGU for selecting me as one of the five recipient of the 2014 Ambassador Award, which also includes election as a Union Fellow. I thank my colleague Steve Ingebritsen for nominating me. As Steve’s citation mentions my work on the Deepwater Horizon oil spill response, I would like to reflect on this experience. The Deepwater Horizon oil spill is well documented in the report of the National Commission on the BP Deepwater Horizon Oil Spill and Offshore Drilling (2011). Washington Post writer John Achenbach’s (2011) book gives a behind-the-scene portrayal of the crisis and explains oil drilling technology in layman’s terms. A special feature in the Proceedings of the National Academy of Sciences (v. 109, no. 50, December 11, 2012) presents 4 perspectives and 11 research articles on “Science Applications in the Deepwater Horizon Oil Spill.” Here, I will simply share my personal perspective.

PCDD/Fs and DL-PCBs in feeding fats obtained as co-products or by-products derived from the food chain.

PubMed

Abalos, M; Parera, J; Abad, E; Rivera, J

2008-04-01

Among the tasks included in the "Quality and safety of feeding fats obtained from co-products or by-products of the food chain" Project, supported by the European Union and included in the 6th Framework Program, a number of fats and oils collected as co- or by-products from the food chain were selected for the determination of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and 'dioxin-like' polychlorinated biphenyls (DL-PCBs). In the majority of the cases these samples are currently employed as feed ingredients. Nevertheless, additional fats, which are forbidden for feedstuff purposes were also considered in this study. In general terms, fats and oils were classified taking into account their nature and the processes applied to obtain these co- or by-products. PCDD/F and DL-PCB levels were evaluated in a first group of samples composed of fish oils, animal fats and lecithins. As expected, fats and oils with an animal origin presented higher concentrations, expressed in pg WHO-TEQ/g, compared to the levels found in vegetable samples like lecithins. The category of fish oils had the highest values for both PCDD/Fs and the sum of PCDD/Fs and DL-PCBs, with some samples showing levels above the maximum established at the present legislation related to the presence of PCDD/Fs and DL-PCBs in animal feed [Commission Directive 2006/13/EC of 3 February 2006 amending Annexes I and II to Directive 2002/32/EC of the European Parliament and of the Council on undesirable substances in animal feed as regards dioxins and dioxin-like PCBs. Official Journal of the European Communities L32, 44-53]. In a second group, fats and oils with a more complex composition obtained from different transformation processes or even mixtures of fats were considered; thus, acid oils from chemical refining, acid oils from physical refining, recycled cooking oils, oils extracted from exhausted bleaching earths, hydrogenated by-products, fatty acids calcium soaps and miscellaneous fats were analyzed. The data revealed a significant variability in PCDD/F and DL-PCB levels, expressed in pg WHO-TEQ/g, in these products. It has to be pointed out that the analyses of fats and oils belonging to these categories of products were sometimes difficult due to the complexity of the samples. In terms of legislation most of these samples cannot be easily included into one of the specific categories of substances intended for feedstuff purposes that are regulated in Commission Directive 2006/13/EC.

Ocean Pollution as a Result of Onshore Offshore Petroleum Activities in the African Gulf of Guinea Region

NASA Astrophysics Data System (ADS)

Abubakar, B.

2007-05-01

The Gulf of Guinea region is located on the Atlantic side of Africa; the sub region has a total population of approximately 190million people. It comprises of five different countries and their territorial waters, which are as follows: Nigeria, Sao Tome & Principe, Equatorial Guinea, Gabon and Cameroon. The sub region is blessed with so many types of natural resources ranging from petroleum, Natural gas, Bitumen, Uranium Diamond and Gold to mention but a few. However the region since the last two decades started attracting the World's attention as a result of the continuous increasing discoveries of new oil fields on both its on shores and off shores. In view of this extra ordinary increasing discoveries of new oil fields in the region, the Gulf of Guinea has become a "Gold rush" to the oil companies and it has so far attracted almost all the top oil firms in the world including; Exxon Mobil, Shell, Total, Texaco, Agip, Chevron, Slumberger, Stat Oil and Conoco Phillips among many other oil giants. In the more recent time even the U.S. Marine Corp have stationed their War Ship in the territorial waters of the Gulf in the name of providing protection to the "Liquid Gold" (Petroleum) underlying the beneath of the region. OIL ACTIVITIES AND ITS ASSOCIATED PROBLEMS IN THE GULF OF GUINEA As a result of the geometrically increasing oil activities in the region ranging from Drilling, Gas flaring, Bunkering and Exploration activities, there was increase in the general pollution of the region. For example recent reports released in June, 2005 by the internationally renown nongovernmental organization on environmental pollution the Netherlands based Climate Justice programme and the Nigeria's Environmental Rights Action, Under the aegis of friends of the Earth, had it that the region is ranked top on the world's total flare with Nigeria along accounting for 16 percent of the world's total flare. Another example is the increasing cases of oil spillages leading to the increasing cases of pollution of farmlands, rivers, wells and the environment in general. Apart from all these, what is even becoming more worrisome is that none of all these oil firms operating in the region is able to account on how it disposes its industrial toxic waste generated as a result of its industrial activities within the region. Finally Geological strata are adversely destroyed by seismographic activities, Sea creatures are destroyed by oil pollution and Means of livelihood of revering dwellers are often threatened by pollution. RECOMMENDATIONS After identifying how the pollution in the Gulf of Guinea region is increasing in relation to the increasing petroleum activities, I have come up with the following suggestions/recommendations. 1. AFRICAN UNION RESOLUTION The Organization of the Petroleum Exporting Countries (OPEC) in conjunction with the International Atomic Energy Agency (IAEA) should use their capacity to be able to influence the African Union (AU) to pass a resolution banning the illegal dumping of radioactive waste, Gas flaring and Costal bunkering in this part of the world. 2. RESEARCH AND INVESTIGATION The Organization of the Petroleum Exporting Countries, in conjunction with the United Nations Environmental Agency, the International Atomic Energy Agency and with the corporation of the African Union should send team of researchers to come and investigate this trend on petroleum pollution in the Gulf of Guinea region and proffer possible solutions in checking the menace.

Oil products prospects for an open trading regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendt, E.A.

The author shows how an open trading regime for oil products can establish a bond of union and friendship and avoid the discord that often characterizes energy trade. Positive actions to implement the International Energy Agency decision to take a common approach rather than individual protectionist actions are the only way to resolve problems arising from growing imports of refined products in Organization of Economic Cooperation and Development countries. The US can show leadership in this effort, but it is unrealistic to expect US markets to remain open if others are closed.

Burma (Myanmar) Country Analysis Brief

EIA Publications

2016-01-01

Burma (Myanmar) is an important natural gas producer in Southeast Asia, although its upstream hydrocarbons sector is severely underdeveloped. Financial constraints by Burma’s national oil company, a lack of technical capacity, opaque regulatory policy, insufficient investment by foreign firms, and international sanctions have significantly impeded the country’s efforts to realize its oil and natural gas production potential. These factors have also severely hampered the development of necessary energy infrastructure. However, U.S. and European Union sanctions were eased or suspended in 2012 and 2013 in response to political and economic reforms in Burma.

Protecting Profits Derived from Tribal Resources: Why the State of Utah Should Not Have the Power To Tax Non-Indian Oil and Gas Lessees on the Navajo Nation's Aneth Extension. Texaco, Exxon, and Union Oil v. San Juan County School District: A Case Study.

ERIC Educational Resources Information Center

Ansson, Richard J., Jr.

1997-01-01

After the Aneth Extension (Utah) was added to the Navajo Reservation in 1933, Congress provided that part of natural resource royalties go to the state to finance education and other services for Navajo residents. These funds were squandered. A Utah Supreme Court case over dual taxation by state and tribe of non-Indian resource lessees is…

Great Lakes and St. Lawrence Seaway Navigation Season Extension. Volume 3. Appendix C. Public Views and Responses on the Report and Environmental Impact Statement

DTIC Science & Technology

1979-08-01

Association Save the River Committee (St. Lawrence River) Seafarers Tnternational Union Sierra Club Southeast Michigan Council of Governments U.S. Great Lakes...the area of oil and hazardous substance spills and how they would be handled. After the general meeting, the audience was divided into three groups for...water during the winter shows up on beaches in the spring. j. Should oil tankers and chemical tankers be rebtricted after December 15? k. There needs to

Syria Country Analysis Brief

EIA Publications

2015-01-01

Syria's energy sector has encountered a number of challenges as a result of conflict and subsequent sanctions imposed by the United States and the European Union. Damage to energy infrastructure—including oil and natural gas pipelines and electricity transmission networks—hindered the exploration, development, production, and transport of the country's energy resources.

Publications - GMC 77 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a California Leffingwell #1 well Authors: Unknown Publication Date: 1988 Publisher: Alaska Division of for the Union Oil Company of California Leffingwell #1 well: Alaska Division of Geological &

A Simple and Effective Mass Spectrometric Approach to Identify the Adulteration of the Mediterranean Diet Component Extra-Virgin Olive Oil with Corn Oil.

PubMed

Di Girolamo, Francesco; Masotti, Andrea; Lante, Isabella; Scapaticci, Margherita; Calvano, Cosima Damiana; Zambonin, Carlo; Muraca, Maurizio; Putignani, Lorenza

2015-09-01

Extra virgin olive oil (EVOO) with its nutraceutical characteristics substantially contributes as a major nutrient to the health benefit of the Mediterranean diet. Unfortunately, the adulteration of EVOO with less expensive oils (e.g., peanut and corn oils), has become one of the biggest source of agricultural fraud in the European Union, with important health implications for consumers, mainly due to the introduction of seed oil-derived allergens causing, especially in children, severe food allergy phenomena. In this regard, revealing adulterations of EVOO is of fundamental importance for health care and prevention reasons, especially in children. To this aim, effective analytical methods to assess EVOO purity are necessary. Here, we propose a simple, rapid, robust and very sensitive method for non-specialized mass spectrometric laboratory, based on the matrix-assisted laser desorption/ionization mass spectrometry (MALDI-TOF MS) coupled to unsupervised hierarchical clustering (UHC), principal component (PCA) and Pearson's correlation analyses, to reveal corn oil (CO) adulterations in EVOO at very low levels (down to 0.5%).

A Simple and Effective Mass Spectrometric Approach to Identify the Adulteration of the Mediterranean Diet Component Extra-Virgin Olive Oil with Corn Oil

PubMed Central

Di Girolamo, Francesco; Masotti, Andrea; Lante, Isabella; Scapaticci, Margherita; Calvano, Cosima Damiana; Zambonin, Carlo; Muraca, Maurizio; Putignani, Lorenza

2015-01-01

Extra virgin olive oil (EVOO) with its nutraceutical characteristics substantially contributes as a major nutrient to the health benefit of the Mediterranean diet. Unfortunately, the adulteration of EVOO with less expensive oils (e.g., peanut and corn oils), has become one of the biggest source of agricultural fraud in the European Union, with important health implications for consumers, mainly due to the introduction of seed oil-derived allergens causing, especially in children, severe food allergy phenomena. In this regard, revealing adulterations of EVOO is of fundamental importance for health care and prevention reasons, especially in children. To this aim, effective analytical methods to assess EVOO purity are necessary. Here, we propose a simple, rapid, robust and very sensitive method for non-specialized mass spectrometric laboratory, based on the matrix-assisted laser desorption/ionization mass spectrometry (MALDI-TOF MS) coupled to unsupervised hierarchical clustering (UHC), principal component (PCA) and Pearson’s correlation analyses, to reveal corn oil (CO) adulterations in EVOO at very low levels (down to 0.5%). PMID:26340625

Applicability of the theory of customs unions to the case of the cooperation council for the Arab States of the Gulf (The GCC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

As-Sudais, A.A.S.

1985-01-01

In 1981, six Arab Gulf states formed the Gulf Cooperation Council (GCC). These states are Bahrain, Kuwait, Oman, Qatar, Saudi Arabia, and the United Arab Emirates (UAE). One of the main stated objectives of the GCC is regional economic integration. This objective was expressed in the GCC Unified Economic Agreement which called for gradual creation of the GCC common market and cooperation and coordination in all economic fields at all levels. The GCC has chosen to approach economic integration in a gradual manner. The first step taken was the formation of a customs union. This study investigates the applicability ofmore » the theory of customs unions to this particular group at this time. The economies of the GCC members exhibit similar characteristics such as reliance on the export of a single nonrenewable commodity (oil), similar large-scale industrial projects (mainly petrochemicals), lack of complementarity of economic resource endowment, and little diversity in industrial production. The main conclusion of the study is that the possible gains suggested by the theory of customs unions are not expected to be realized to a significant extent as a result of forming the GCC customs union. Trade effects (if any) will be negligible due to various factors including low-pre-union tariff levels.« less

HPLC study of migration of terephthalic acid and isophthalic acid from PET bottles into edible oils.

PubMed

Khaneghah, Amin Mousavi; Limbo, Sara; Shoeibi, Shahram; Mazinani, Somayeh

2014-08-01

Polyethylene terephthalate (PET) containers for food oil packaging were evaluated with a newly established determination method for terephthalic acid (TPA) and isophthalic acid (IPA). The analysis of monomers, TPA and IPA that migrate from PET bottles into oils was performed using high-pressure liquid chromatography with a diode array detector. Three types of commercial oils (sunflower oil, canola oil and blended oil which included sunflower oil, soy bean oil and cottonseed oil) were bottled in PET containers. These samples were incubated for 10 days at 49 °C as accelerated test condition. The means of recovery for this method varied from 70% to 72% and from 101% to 111% for TPA and IPA, respectively. The results showed that the amounts of specific migration of TPA and IPA into the samples conform to European Union legislation that identifies specific migration limits. More important, the results highlighted a different behavior of migration as a function of the fatty acid profile. Previous investigations have been performed with food simulants such as HB307 or 20% ethanol but our study used real food samples and determined trace amounts of the migrated compounds. Further investigation will be needed to better explain the influence of fatty acid conformation on migration of PET monomers. © 2013 Society of Chemical Industry.

Publications - GMC 90 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a -1 (Hammerhead) well Authors: Unknown Publication Date: 1988 Publisher: Alaska Division of Geological for the Union Oil Company OCS-Y-0849-1 (Hammerhead) well: Alaska Division of Geological &

Publications - GMC 80 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a California Tungak Creek #1 well Authors: Unknown Publication Date: 1988 Publisher: Alaska Division of for the Union Oil Company of California Tungak Creek #1 well: Alaska Division of Geological &

Evaluation of available data on the geohydrology, soil chemistry, and ground-water chemistry of Gas Works Park and surrounding region, Seattle, Washington

USGS Publications Warehouse

Sabol, M.A.; Turney, G.L.; Ryals, G.N.

1988-01-01

Gas Works Park, in Seattle, Washington, is located at the site of an abandon gasification plant on Lake Union. Wastes deposited during 50 years of plant operations (1906-1956) have extended the shore line 100 ft and left the park soil contaminated with a number of hazardous material. Soil contaminants include polynuclear aromatic hydrocarbons (PAHs), polychlorinated biphenyls, pesticides, volatile organic compounds, cyanide, and metals. PAHs and metals have been detected in Lake Union sediments. Maximum total PAH concentrations exceeded 100 million micrograms/kilogram in some places in the soils of the park at 6-inch depths and in some lake sediments. Other contaminants present are much lower in concentrations. The park is on glacial drift overlain by gasification waste materials and clean fill. Waste materials include sand and gravels, mixed with lampblack, oil, bricks, and other industrial wastes. Groundwater flows through the soils and waste toward Lake Union. Vertical groundwater movement is uncertain, but is assumed to be upward near Lake Union. Concentrations of most soil contaminants are probably low in the groundwater and in Lake Union due to the low solubilities and high sorptive characteristics of these contaminants. However, no water quality data are available to confirm this premise. (USGS)

An Experimental Evaluation of Oil Pumping Rings

NASA Technical Reports Server (NTRS)

Eusepi, M. W.; Walowit, J.; Cohen, M.

1981-01-01

The design and construction of a reciprocating test vehicle to be used in evaluating hydrodynamic oil pumping rings are discussed. In addition, experimental test data are presented for three pumping ring designs that were constructed from Tin-Based Babbitt (SAE 11), Bearing Bronze (SAE 660), and Mechanical Carbon Graphite (Union Carbide Grade CNF-J). Data of pumped flow rate versus delivered pressure, as well as friction loss, are reported for the following conditions: frequencies of 10, 35 and 45 Hz; strokes of 25.4 mm (1.00 in.), 38.1 mm (1.50 in.) and 50.8 mm (2.00 in.) oil inlet temperature of 49 degrees (120 degrees); and pumping ring close-in pressures of 10.3 MPa (1500 lb/square inch. A 20W40 automotive oil was used for all tests. The maximum delivered pressure was 11 MPa (1600 lb/square inch. An analysis of hydrodynamic oil pumping rings was performed and the results of the analysis were compared to measured test data.

Mutual Predators: An Examination of Russia's Oil, Gas, and Nuclear Sectors in the Post-Soviet Era

NASA Astrophysics Data System (ADS)

Rousselle, Adam

Russia's energy sector has changed dramatically over the past three decades and this study examines this change within the oil, gas, and nuclear sectors. Having inherited a state capitalist system after the fall of the Soviet Union, Russia's bureaucracy now presides over an incredibly rich and deeply problematic energy economy. At its core, this is a study on institutionalized corruption and the behavior of corrupt elites. More specifically, it examines whether Russia can succeed within this context and what this may teach us on the nature of corrupt states and institutions.

Microbial communities in the functional areas of a biofilm reactor with anaerobic-aerobic process for oily wastewater treatment.

PubMed

Li, Jianhua; Sun, Shanshan; Yan, Ping; Fang, Li; Yu, Yang; Xiang, Yangdong; Wang, Di; Gong, Yejing; Gong, Yanjun; Zhang, Zhongzhi

2017-08-01

Microbial communities in the functional areas of biofilm reactors with large height-diameter ratio using the anaerobic-aerobic (A/O) reflux process was investigated to treat heavy oil refinery wastewater without pretreatment. In the process, chemical oxygen demand (COD) and total nitrogen (TN) removal reached 93.2% and 82.8%, and the anaerobic biofilm reactor was responsible for 95% and 99%, respectively. Areas for hydrolysis acidification and acetic acid production, methane production, and COD recovery were obvious in the anaerobic reactor. Among all areas, area for hydrolysis acidification and acetic acid production was the key factor to improve COD removal efficiency. High throughput sequencing of 16S rDNA gene showed that the native community was mainly composed of functional groups for hydrocarbon degradation, syntrophic bacteria union body, methanogenesis, nitrification, denitrification, and sulfate reduction. The deviations between predicted values and actual COD and TN removal were less than 5% in the optimal prediction model. Copyright © 2017 Elsevier Ltd. All rights reserved.

Medical Device Regulation: A Comparison of the United States and the European Union.

PubMed

Maak, Travis G; Wylie, James D

2016-08-01

Medical device regulation is a controversial topic in both the United States and the European Union. Many physicians and innovators in the United States cite a restrictive US FDA regulatory process as the reason for earlier and more rapid clinical advances in Europe. The FDA approval process mandates that a device be proved efficacious compared with a control or be substantially equivalent to a predicate device, whereas the European Union approval process mandates that the device perform its intended function. Stringent, peer-reviewed safety data have not been reported. However, after recent high-profile device failures, political pressure in both the United States and the European Union has favored more restrictive approval processes. Substantial reforms of the European Union process within the next 5 to 10 years will result in a more stringent approach to device regulation, similar to that of the FDA. Changes in the FDA regulatory process have been suggested but are not imminent.

Publications - GMC 118 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Company OCS Y-0849-2 (Hammerhead #2) well Authors: Unknown Publication Date: 1989 Publisher: Alaska reflectance data of cuttings from the Union Oil Company OCS Y-0849-2 (Hammerhead #2) well: Alaska Division of

News from the Suncoast Chapter

NASA Astrophysics Data System (ADS)

AGU's serenely-named Suncoast Chapter, one of the union's several regional groups, met twice during the 1989-1990 academic year. The fall meeting featured four panelists discussing “An Oil Spill in Tampa Bay—A Disaster Waiting to Happen.” The spring meeting hosted Arthur D. Weissman, chief of the Guidance and Oversight Branch of the Environmental Protection Agency, speaking

A VIEW OF TURKEY AND EUROPEAN RELATIONS FROM THE PERSPECTIVE OF MEDICAL LEGISLATION: AN ASSESMENT OF STATE OF PLAY

PubMed Central

Ekmekçi, Perihan Elif; Arda, Berna

2015-01-01

The aim of this paper is to reflect the situation of health legislation alignment in Turkey in its accession process to the European Union and Customs Union Agreement, and to discuss the the EU’s health priorities of in parallel with the Turkish ones. The health legislation alignment processes consist of three titles which are: European Union alignment process, the harmonization done in the framework of membership to Council of Europe, and the obligations under the Customs Union Agreement. Significant human resources are required for the adoption of the legislations which make ethically imperative the discussion of whether there is a harmony among the priorities of both parities. Unless this harmony and paralellisim is shown, the human resources appointed for the adoption of health legislation process would not prove their efficiency and effectiveness. In this article, the Customs Union and formal negotiations for full EU membership are included in the phrase “the alignment process to European Union”. Council Decisions 1/95 and 2/97 ground on the obligations provided by the Customs Union Agreement. The reference document used to discuss the formal negotiation process for full membership to European Union is the Turkish National Program for the Adoption of the EU Acquis 2008–2013. The legislative obligations of Turkey arising from its membership of the Council of Europe, which has significant contributions to the medical legislation especially in the field of medical ethics, are also included in this article. PMID:26269696

Transcriptomic Analysis Provides Insights into Grafting Union Development in Pecan (Carya illinoinensis).

PubMed

Mo, Zhenghai; Feng, Gang; Su, Wenchuan; Liu, Zhuangzhuang; Peng, Fangren

2018-02-05

Pecan ( Carya illinoinensis ), as a popular nut tree, has been widely planted in China in recent years. Grafting is an important technique for its cultivation. For a successful grafting, graft union development generally involves the formation of callus and vascular bundles at the graft union. To explore the molecular mechanism of graft union development, we applied high throughput RNA sequencing to investigate the transcriptomic profiles of graft union at four timepoints (0 days, 8 days, 15 days, and 30 days) during the pecan grafting process. After de novo assembly, 83,693 unigenes were obtained, and 40,069 of them were annotated. A total of 12,180 differentially expressed genes were identified between by grafting. Genes involved in hormone signaling, cell proliferation, xylem differentiation, cell elongation, secondary cell wall deposition, programmed cell death, and reactive oxygen species (ROS) scavenging showed significant differential expression during the graft union developmental process. In addition, we found that the content of auxin, cytokinin, and gibberellin were accumulated at the graft unions during the grafting process. These results will aid in our understanding of successful grafting in the future.

Transcriptomic Analysis Provides Insights into Grafting Union Development in Pecan (Carya illinoinensis)

PubMed Central

Mo, Zhenghai; Feng, Gang; Su, Wenchuan; Liu, Zhuangzhuang; Peng, Fangren

2018-01-01

Pecan (Carya illinoinensis), as a popular nut tree, has been widely planted in China in recent years. Grafting is an important technique for its cultivation. For a successful grafting, graft union development generally involves the formation of callus and vascular bundles at the graft union. To explore the molecular mechanism of graft union development, we applied high throughput RNA sequencing to investigate the transcriptomic profiles of graft union at four timepoints (0 days, 8 days, 15 days, and 30 days) during the pecan grafting process. After de novo assembly, 83,693 unigenes were obtained, and 40,069 of them were annotated. A total of 12,180 differentially expressed genes were identified between by grafting. Genes involved in hormone signaling, cell proliferation, xylem differentiation, cell elongation, secondary cell wall deposition, programmed cell death, and reactive oxygen species (ROS) scavenging showed significant differential expression during the graft union developmental process. In addition, we found that the content of auxin, cytokinin, and gibberellin were accumulated at the graft unions during the grafting process. These results will aid in our understanding of successful grafting in the future. PMID:29401757

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Reich Farm site is located in Dover Township, Ocean County, New Jersey. The site is currently owned by Mr. and Mrs. Samuel Reich. In August 1971, they rented a portion of their land to Mr. Nicholas Fernicola for temporary storage of used 55-gallon drums. Most of the drums had Union Carbide Corporation (UCC) markings on them, with labels reading 'tar pitch,' 'lab waste solvent,' 'blend of resin and oil,' and 'solvent wash of process stream' among others. The site first came to the attention of the New Jersey Superior Court when the Reichs filed suit against Mr. Fernicola andmore » UCC. The primary contaminants of concern affecting the ground water and soils are VOCs including 1,1,1-trichloroethane (TCA), TCE, PCE, and semi-volatile organics compounds (SVOCs). The selected remedial action for the site is included.« less

Uzbek licensing round brings geology, potential into focus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heafford, A.P.; Lichtman, G.S.

1993-08-09

Uzbekistan is a Central Asian Republic that declared independence from the former Soviet Union in 1991. Uzbekistan produces about 18 million bbl/year of oil and 40 bcf/year of gas. It is the third largest gas producer in the Commonwealth of Independent States and imports oil. The Uzbek government and oil and gas industry are offering exploration acreage for foreign participation via competitive bid. Acreage on offer includes fields for development and unproven-underexplored areas. Terms awaiting approval by the Cabinet of Ministers provide financial incentives for rapid development of existing reserves, creation of required infrastructure, and long term investment growth. Licensemore » areas concentrate on acreage where western equipment and technology can bring new reserves economically on line in the near future. National oil company Uzbekneftegaz was created in 1992 to oversee the extraction, transport, and refining of hydrocarbons in Uzbekistan. The paper describes some of the fields and infrastructure in place, the structural geology, stratigraphy, petroleum distribution, source rocks, reservoir rocks, cap rocks, traps, and hydrocarbon composition, which includes oil, gases, and gas condensates.« less

75 FR 20335 - Certain Oil Country Tubular Goods from the People's Republic of China: Final Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-19

... tubing, of iron (other than cast iron) or steel (both carbon and alloy), whether seamless or welded... Seamless Tube Mill of Inner Mongolia Baotou Steel 29.94 and Trading Co., Ltd Union Co., Ltd.\\27\\ Benxi... Century Machinery Co. Ltd.;Tianjin Seamless Steel Pipe Plant; Baoshan Iron & Steel Co. Ltd Shengli...

76 FR 64425 - Union Pacific Railroad Company-Abandonment Exemption-in Pottawattamie County, IA; Iowa Interstate...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-18

... trackage rights and UP's overhead trackage rights, UP will sell the UP lines to a shipper, Red Giant Oil Company (Red Giant), subject to a permanent access easement over the UP lines for another shipper, Midwest Walnut Company of Iowa (Midwest Walnut). Red Giant and Midwest Walnut are the only shippers on the UP...

U.S. Policy in the Persian Gulf: New Beginnings.

ERIC Educational Resources Information Center

Husbands, Jo

For 40 years the primary objectives of U.S. policy in the Persian Gulf have been to assure access by the industrialized nations to the region's oil and to prevent those resources from falling under the control of the Soviet Union or any other hostile power. The recent events in Iran, the Iran-Iraq War and its aftermath, the maneuvering of a…

Spectroscopy applied to feed additives of the European Union Reference Laboratory: a valuable tool for traceability.

PubMed

Omar, Jone; Slowikowski, Boleslaw; Boix, Ana; von Holst, Christoph

2017-08-01

Feed additives need to be authorised to be placed on the market according to Regulation (EU) No. 1831/2003. Next to laying down the procedural requirements, the regulation creates the European Union Reference Laboratory for Feed Additives (EURL-FA) and requires that applicants send samples to the EURL-FA. Once authorised, the characteristics of the marketed feed additives should correspond to those deposited in the sample bank of the EURL-FA. For this purpose, the submitted samples were subjected to near-infrared (NIR) and Raman spectroscopy for spectral characterisation. These techniques have the valuable potential of characterising the feed additives in a non-destructive manner without any complicated sample preparation. This paper describes the capability of spectroscopy for a rapid characterisation of products to establish whether specific authorisation criteria are met. This study is based on the analysis of feed additive samples from different categories and functional groups, namely products containing (1) selenium, (2) zinc and manganese, (3) vitamins and (4) essential oils such as oregano and thyme oil. The use of chemometrics turned out to be crucial, especially in cases where the differentiation of spectra by visual inspection was very difficult.

Timing of oil and gas generation of petroleum systems in the Southwestern Wyoming Province

USGS Publications Warehouse

Roberts, L.N.R.; Lewan, M.D.; Finn, T.M.

2004-01-01

Burial history, thermal maturity, and timing of petroleum generation were modeled for eight key source-rock horizons at seven locations throughout the Southwestern Wyoming Province. The horizons are the bases of the Lower Permian Phosphoria Formation, the Upper Cretaceous Mowry Shale, Niobrara Formation, Baxter Shale (and equivalents), upper part of the Mesaverde Group, Lewis Shale, Lance Formation, and the Tertiary (Paleocene) Fort Union Formation. Burial history locations include three in the deepest parts of the province (Adobe Town in the Washakie Basin, Eagles Nest in the Great Divide Basin, and Wagon Wheel in the northern Green River Basin); two at intermediate basin depths (Federal 31-1 and Currant, Creek in the central and southern parts of the Green River Basin, respectively); and two relatively shallow locations (Bear 1 on the southeastern margin of the Sand Wash Basin and Bruff 2 on the Moxa arch). An overall ranking of the burial history locations in order of decreasing thermal maturity is Adobe Town > Eagles Nest > Wagon Wheel > Currant Creek > Federal 31-1 > Bear-1 > Bruff 2. The results of the models indicate that peak petroleum generation from Cretaceous oil- and gas-prone source rocks in the deepest parts of the province occurred from Late Cretaceous through middle Eocene. At the modeled locations, peak oil generation from source rocks of the Phosphoria Formation, which contain type-IIS kerogen, occurred in the Late Cretaceous (80 to 73 million years ago (Ma)). Gas generation from the cracking of Phosphoria oil reached a peak in the late Paleocene (57 Ma) only in the deepest parts of the province. The Mowry Shale, Niobrara Formation, and Baxter Shale (and equivalents) contain type-IIS or a mix of type-II and type-III kerogens. Oil generation from these units, in the deepest parts of the province, reached peak rates during the latest Cretaceous to early Paleocene (66 to 61 Ma). Only at these deepest locations did these units reach peak gas generation from the cracking of oil, which occurred in the early to late Eocene (52 to 41 Ma). For the Mesaverde Group, which also contains a mix of type-II and type-III kerogen, peak oil generation occurred only in the deepest parts of the province during middle Eocene (50 to 41 Ma). Only at Adobe Town did cracking of oil occur and gas generation reach peak in the earliest Oligocene (33 Ma). Gas-prone source rocks (type-III kerogen) of the Mowry and Baxter (and equivalents) Shales reached peak gas generation in the latest Cretaceous (66 Ma) in the deepest parts of the province. At the shallower Bear 1 location, the Mancos Shale (Baxter equivalent) source rocks reached peak gas generation at about this same time. Gas generation from the gas-prone Mesaverde source rocks started at all of the modeled locations, but reached peak generation at only the deepest locations in the early Eocene (54 to 49 Ma). The Lewis Shale, Lance Formation, and Fort Union Formation all contain gas-prone source rocks with type-III kerogen. Peak generation of gas from the Lewis Shale occurred only at Eagles Nest and Adobe Town in the early Eocene (52 Ma). Source rocks of the Lance reached peak gas generation only at the deepest locations during the middle Eocene (48 to 45 Ma) and the Fort Union reached peak gas generation only at Adobe Town also in the middle Eocene (44 Ma).

Single-laboratory validation of a GC/MS method for the determination of 27 polycyclic aromatic hydrocarbons (PAHs) in oils and fats.

PubMed

Rose, M; White, S; Macarthur, R; Petch, R G; Holland, J; Damant, A P

2007-06-01

A protocol for the measurement of 27 polycyclic aromatic hydrocarbons (PAHs) in vegetable oils by GC/MS has undergone single-laboratory validation. PAHs were measured in three oils (olive pomace, sunflower and coconut oil). Five samples of each oil (one unfortified, and four fortified at concentrations between 2 and 50 microg kg(-1)) were analysed in replicate (four times in separate runs). Two samples (one unfortified and one fortified at 2 microg kg(-1)) of five oils (virgin olive oil, grapeseed oil, toasted sesame oil, olive margarine and palm oil) were also analysed. The validation included an assessment of measurement bias from the results of 120 measurements of a certified reference material (coconut oil BCR CRM458 certified for six PAHs). The method is capable of reliably detecting 26 out of 27 PAHs, at concentration <2 microg kg(-1) which is the European Union maximum limit for benzo[a]pyrene, in vegetable oils, olive pomace oil, sunflower oil and coconut oil. Quantitative results were obtained that are fit for purpose for concentrations from <2 to 50 microg kg(-1) for 24 out of 27 PAHs in olive pomace oil, sunflower oil and coconut oil. The reliable detection of 2 microg kg(-1) of PAHs in five additional oils (virgin olive oil, grapeseed oil, toasted sesame oil, olive margarine and palm oil) has been demonstrated. The method failed to produce fit-for-purpose results for the measurement of dibenzo[a,h]pyrene, anthanthrene and cyclopenta[c,d]pyrene. The reason for the failure was the large variation in results. The likely cause was the lack of availability of (13)C isotope internal standards for these PAHs at the time of the study. The protocol has been shown to be fit-for-purpose and is suitable for formal validation by inter-laboratory collaborative study.

Lippia origanoides essential oil: an efficient and safe alternative to preserve food, cosmetic and pharmaceutical products.

PubMed

Hernandes, C; Pina, E S; Taleb-Contini, S H; Bertoni, B W; Cestari, I M; Espanha, L G; Varanda, E A; Camilo, K F B; Martinez, E Z; França, S C; Pereira, A M S

2017-04-01

The aim of this work was to evaluate the efficacy and safety of Lippia origanoides essential oil as a preservative in industrial products. The composition, antimicrobial activity, mutagenic and toxic potential of L. origanoides were determined. Then, the effect of essential oil as a preservative in food, cosmetics and pharmaceutical products was evaluated. The essential oil of L. origanoides consisted mainly of oxygenated monoterpenes (38·13%); 26·28% corresponded to the compound carvacrol. At concentrations ranging from 0·312 to 1·25 μl ml -1 and in association with polysorbate 80, the essential oil of L. origanoides inhibited the growth of all the tested micro-organisms. The medium lethal dose in mice was 3·5 g kg -1 , which categorizes it as nontoxic according to the European Union criteria, and negative results in the Ames test indicated that this oil was not mutagenic. In combination with polysorbate 80, the essential oil exerted preservative action on orange juice, cosmetic and pharmaceutical compositions, especially in the case of aqueous-based products. Lippia origanoides essential oil is an effective and safe preservative for orange juice, pharmaceutical and cosmetic products. This study allowed for the complete understanding of the antimicrobial action and toxicological potential of L. origanoides essential oil. These results facilitate the development of a preservative system based on L. origanoides essential oil. © 2017 The Society for Applied Microbiology.

From the Oracles of the Temple of Janus: "Chicago Teachers Union v. Hudson."

ERIC Educational Resources Information Center

Vieira, Edwin, Jr.

1986-01-01

Examines "Chicago Teachers Union v. Hudson," a United States Supreme Court decision guaranteeing non-union government workers specific protections of procedural due process that certain educational and teacher unions had failed to recognize. Decries the "Hudson" decision for separating labor law from laws governing the rest of…

Worker Participation and American Unions. Threat or Opportunity?

ERIC Educational Resources Information Center

Kochan, Thomas A.; And Others

This book reports results of a study of the efects of quality of worklife programs and related forms of worker participation on unions and the collective bargaining process. Chapter 1 describes the evolution of worker participation in unionized settings and summarizes basic propositions in models of joint union-management change. In chapter 2 five…

Time and temperature in petroleum formation: application of Lopatin's method to petroleum exploration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waples, D.W.

1980-06-01

N.V. Lopatin in the Soviet Union has developed a method for taking both time and temperature into account as factors in thermal maturation of kerogen. Lopatin's time-temperature index of maturity (TTI) values correlate with the thermal regimes corresponding to generation and preservation of hydrocarbons. Because such information is potentially of great interest for oil exploration, a calibration and evaluation have been made of Lopatin's method. Within the limitations of the date presently available the following statements can be made: 1. The rate of the chemical reactions involved in thermal maturation of organic material appears to double with every 10/sup 0/Cmore » (18/sup 0/F) rise in temperature. 2. Threshold values of Lopatin's time-temperature index of maturity (TTI) are: 15 onset of oil generation; 75 peak oil generation; 160 end oil generation; approx. 500 40/sup 0/ oil preservation deadline; approx. 1000 50/sup 0/ oil preservation deadline; approx. 1500 wet gas preservation deadline; and > 65,000 dry gas preservation deadline. 3. TTI values calculated from Lopatin reconstructions consistently agree with other maturation parameters commonly used by petroleum geochemists. Potential applications of Lopatin's method for oil exploration include timing of oil generation, calculation of volume of hydrocarbons generated within a basin, and determination of economic deadlines. 13 figures, 5 tables.« less

East Asia: Southeast Asia

DTIC Science & Technology

1990-07-25

failing to resolve the question of oil royalties and the problem of about 500,000 aliens in Sabah. They have raised these subjects as issues in the...is active. He also criticized leaders of the Malaysian Trade Union Congress (MTUC), Zainal Rampak and V. David, for cooperating with U.S...mittee for the Federal Territory, Datuk Drs. Suleiman Mohamad; chairman of the MIC [ Malaysian Indian Congress] for the Federal Territory, S

Airlift and Access in the Indo-Pacific

DTIC Science & Technology

2014-06-01

landing points. These strikes occur before landing forces can disperse, when they are most vulnerable and include wide-area mine fields; contamination of...Taiwan, Malaysia , Philippines, and Vietnam. Second, it establishes rights to fishing, navigation, and oil and gas exploration and drilling activities...to smuggle cotton northward to mix with legal cotton. As Union and merchant ships transported food down the Mississippi for sale, their return

USSR Report, Science and Technology Policy.

DTIC Science & Technology

1987-03-12

producing hydrogen peroxide and monocarboxylic acids for the oil-free production of varnishes and paints. The entire world is using this resource...widely used in the paint, varnish , and food industry, medicine, and other sectors. The All-Union Scientific Seminar that opened on 17 September in...the form of a compound containing fluorine ; compounds of tetravalent nickel were synthesized; lanthanide and transuranic elements have been produced

Dues and Deep Pockets: Public-Sector Unions' Money Machine. Civic Report. No. 67

ERIC Educational Resources Information Center

DiSalvo, Daniel

2012-01-01

At first glance, public-sector labor unions are just one of many types of organizations that participate in the political process. However, these unions differ significantly from other interest groups made up of individual citizens or non-labor organizations. Because their members' interests are tied to government policy, these unions are more…

[Historical and social perspective from the 64-65 Mexican medical movement].

PubMed

Cabello-López, Alejandro; Gopar-Nieto, Rodrigo; Aguilar-Madrid, Guadalupe; Juárez-Pérez, Cuauhtémoc Arturo; Haro-García, Luis Cuauhtémoc

2015-01-01

The Mexican Medical Movement from 1964-1965 constitutes an important event from the rising urban middle-class, besides it was the first time medical doctors claimed for fair working conditions. The background of this movement is the so-called Crisis of 1958, which included the Movements from the educators union, oil workers union, telegraph workers union and the railroad workers union. The conflict began because interns and residents from the "Hospital 20 de Noviembre" would not get a payment at the end of the year, so on November 26th, 1964, the movement started. The Asociación Mexicana de Médicos Residentes e Internos (AMMRI) was created and their demands were the following: 1) Full working site restitution without retaliations, 2) Legal examination of the scholarship-contract terms, in order to get annual, renewable and progressive contracts, and a fixed salary with the usual working-hours and characteristics of each institution, 3) To have preference to get an adscription at the hospital where the resident studied, 4) Active participation from the resident in the elaboration of the academic plans, and 5) Resolution of each hospital's problems. This movement had social impact for Mexico's contemporary life, nevertheless some of the demands are still unchanged among medical residents.

Gary Refining Company emerges from Chapter 11 bankruptcy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-09-01

On July 24, 1986 Gary Refining Company, Inc. announced that the Reorganization Plan for Gary Refining Company, Inc., Gary Refining Company, and Mesa Refining, Inc. has been approved by the United States bankruptcy Court (District of Colorado). The companies filed for protection from creditors on March 4, 1985 under Chapter 11 of the United States Bankruptcy Code. Payments to creditors are expected to begin upon start-up of the Gary Refining Company (GRC) refinery in Fruita, Colorado after delivery of shale oil from Union Oil's Parachute Creek plant. In the interim, GRC will continue to explore options for possible startup (onmore » a full scale or partial basis) prior to that time.« less

A Guide to the Changing Court Rulings on Union Security in the Public Sector: A Union Perspective.

ERIC Educational Resources Information Center

Darko, Richard J.; Knapp, Janet C.

1985-01-01

The Supreme Court in "Ellis vs. Brotherhood of Railway, Airline and Steamship Clerks" has provided a systematic process for determining what constitutes union expenses properly charged to objecting nonmembers. (MLF)

76 FR 10209 - Corporate Credit Unions

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-24

... natural person credit unions (NPCUs) may wish to form new corporates. Previous corporate chartering... NCUA's standards for evaluating applications. It also included detailed timelines for processing... natural person representatives of natural person credit unions (NPCUs)--``the subscribers''--may charter a...

Quality and age of shallow groundwater in the Bakken Formation production area, Williston Basin, Montana and North Dakota

USGS Publications Warehouse

McMahon, Peter B.; Caldwell, Rodney R.; Galloway, Joel M.; Valder, Joshua F.; Hunt, Andrew G.

2015-01-01

The quality and age of shallow groundwater in the Bakken Formation production area were characterized using data from 30 randomly distributed domestic wells screened in the upper Fort Union Formation. Comparison of inorganic and organic chemical concentrations to health based drinking-water standards, correlation analysis of concentrations with oil and gas well locations, and isotopic data give no indication that energy-development activities affected groundwater quality. It is important, however, to consider these results in the context of groundwater age. Most samples were recharged before the early 1950s and had 14C ages ranging from 30,000 years. Thus, domestic wells may not be as well suited for detecting contamination associated with recent surface spills as shallower wells screened near the water table. Old groundwater could be contaminated directly by recent subsurface leaks from imperfectly cemented oil and gas wells, but horizontal groundwater velocities calculated from 14C ages imply that the contaminants would still be less than 0.5 km from their source. For the wells sampled in this study, the median distance to the nearest oil and gas well was 4.6 km. Because of the slow velocities, a long-term commitment to groundwater monitoring in the upper Fort Union Formation is needed to assess the effects of energy development on groundwater quality. In conjunction with that effort, monitoring could be done closer to energy-development activities to increase the likelihood of early detection of groundwater contamination if it did occur.

Use of recovered frying oils in chicken and rabbit feeds: effect on the fatty acid and tocol composition and on the oxidation levels of meat, liver and plasma.

PubMed

Tres, A; Bou, R; Guardiola, F; Nuchi, C D; Magrinyà, N; Codony, R

2013-03-01

The addition of some fat co- and by-products to feeds is usual nowadays; however, the regulations of their use are not always clear and vary between countries. For instance, the use of recycled cooking oils is not allowed in the European Union, but they are used in other countries. However, oils recovered from industrial frying processes could show satisfactory quality for this purpose. Here we studied the effects of including oils recovered from the frying industry in rabbit and chicken feeds (at 30 and 60 g/kg, respectively) on the fatty acid (FA) and tocol (tocopherol + tocotrienol) compositon of meat, liver and plasma, and on their oxidative stability. Three dietary treatments (replicated eight times) were compared: fresh non-used oil (LOX); oil discarded from the frying industry, having a high content of secondary oxidation compounds (HOX); and an intermediate level (MOX) obtained by mixing 50 : 50 of LOX and HOX. The FA composition of oil diets and tissues was assessed by GC, their tocol content by HPLC, the thiobarbituric acid value was used to assess tissue oxidation status, and the ferrous oxidation-xylenol orange method was used to assess the susceptibility of tissues to oxidation. Our results indicate that FA composition of rabbit and chicken meat, liver and plasma was scarcely altered by the addition of recovered frying oils to feed. Differences were encountered in the FA composition between species, which might be attributed mainly to differences in the FA digestion, absorption and metabolism between species, and to some physiological dietary factors (i.e. coprophagy in rabbits that involves fermentation with FA structure modification). The α-tocopherol (αT) content of tissues was reduced in response to the lower αT content in the recovered frying oil. Differences in the content of other tocols were encountered between chickens and rabbits, which might be attributable to the different tocol composition of their feeds, as well as to species differences in the digestion and metabolism of tocols. Tissue oxidation and susceptibility to oxidation were in general low and were not greatly affected by the degree of oxidation of the oil added to the feeds. The relative content of polyunsaturated fatty acids/αT in these types of samples would explain the differences observed between species in the susceptibility of each tissue to oxidation. According to our results, oils recovered from the frying industry could be useful for feed uses.

The Formation and Dissolution of Second Unions: Marriage and Cohabitation in Sweden and Norway.

ERIC Educational Resources Information Center

Blanc, Ann Klimas

1987-01-01

Using recent survey data from Sweden and Norway and life table techniques, examined rate at which women formed second unions and type of union they chose (marriage or cohabitation) as well as how this process has changed over time. The results showed that nonmarital cohabitation was preferred type of second union in both Sweden and Norway.…

Water resources of Hot Springs County, Wyoming

USGS Publications Warehouse

Plafcan, Maria; Ogle, Kathy Muller

1994-01-01

The wells and springs inventoried in Hot Springs County most commonly had been completed in or issued from the Quaternary alluvium, Quaternary terrace deposits, Fort Union and Mesaverde Formations, Cody Shale, and the Frontier and Chugwater Formations. The largest discharges measured were from the Quaternary terrace deposits (400 gallons per minute) and the Phosphoria Formation (1,000 gallons per minute). Discharges from all other geologic units varied, but most wells and springs yielded 50 gallons per minute or less.Water-quality samples collected from springs that issued from the Absaroka Volcanic Supergroup, the Bighorn Dolomite, and the Flathead Sandstone had the lowest dissolved-solids concentrations, which ranged from 58 to 265 milligrams per liter, and the least variable water types. Water from the volcanic rocks was a sodium bicarbonate type; whereas, water from the Flathead Sandstone was a calcium bicarbonate type. Water types for all the other aquifers varied from sampling site to sampling site; however, water samples from the Fort Union Formation and the Cody Shale were consistently of the sodium sulfate type. The effect of oil- and gas-development at Hamilton Dome on thermal spring discharges at Hot Springs State Park near Thermopolis was studied. The estimated drawdown from 1918, when the Hamilton Dome oil field was discovered, to 1988 was made using drill-stem data from previous studies. Drawdown at Big Spring in the Park was estimated to be less than 3 feet on the basis of recent oil- and water-production data, previous modeling studies, and the estimated water-level drawdown of 330 feet in wells at the Hamilton Dome oil field.Streams originating in the Plains region of the county, such as Middle Fork Owl Creek, are ephemeral or intermittent; whereas, streams originating in the mountains, such as Gooseberry Creek, are perennial. Average annual runoff across the county ranges from 0.26 inches at a representative streamflow-gaging station near Worland in the plains region to 5.4 inches in the Owl Creek Mountains and southeastern Absaroka Range.

Clam Shell Dredging in Lakes Pontchartrain and Maurepas, Louisiana. Volume 2. Public Comments.

DTIC Science & Technology

1987-11-01

levels and pattern of distribution of polycyclic aromatic hydrocarbons , is presented, despite the fact that these compounds are identified . . as the...DEIS. Moreover, the DEIS implies that the potential for bioaccumulation of the pollutants present in Lake Ponchartrain is low except for a small...CHEMICAL AIR PRODUCTS SHELL OIL CO SHELL CHEMICAL CIBA GEIGY CORPORATION UNION TEXAS PETROLEUM SAVOIE INDUSTRIES SUNLAND SERVICES VULCAN MATERIAL

Using rare earth elements for the identification of the geographic origin of food

NASA Astrophysics Data System (ADS)

Meisel, T.; Bandoniene, D.; Joebstl, D.

2009-04-01

The European Union defined regimes within the Protected Geographical Status (PGS) framework to protect names of regional food specialities. Thus only food produced in a specific geographical area with a specific way of production or quality can be protected by a protected geographical indication (PGI) label. As such Styrian Pumpkin Seed Oil has been approved with this label, but as with many other high priced regional specialities, fraud cannot be excluded or nor identified. Thus the aim of this work is, to develop an analytical method for the control of the geographic origin of pumpkin seed oil and also to test the method for other protected products. The development of such a method is not only of interest for scientists, but also of importance for the consumer wanting to know the origin of the food products and the assurance of the purity and quality. The group of rare earth elements (REE) in plants also have a characteristic distribution pattern similar to upper crustal REE distributions. Since the REE concentrations are extremely low in pumpkin seed oil (ppt to low ppb), ICP-MS was the only sensitive tool able to produce validated results. The carrier of the REE are most likely small particles distributed within the pumpkin seed oil. Unlike, e.g., olive oil, pumpkin seed oil is bottled and sold unfiltered, which makes this Styrian speciality an interesting sampling target. As pumpkin seed oils from different geographic origin show variable trace element and rare earth distribution patterns, is should possible to trace the origin of these oils. In the current project pumpkin seeds from different regions in Austria and from abroad were sampled. The trace element patterns in the extracted oil of these seeds were determined and a preliminary classification with discriminate analysis was successfully done on a statistical basis. In addition to the study of the geographic origin it was demonstrated that REE distribution patterns can also be used for the identification of adulteration of high priced pumpkin seed oil with cheap neutral tasting refined oils. Interestingly enough, the variations of the REE patterns between oils from different regions are much more pronounced than their host soils. Thus we assume that microbiological processes in the rhizosphere are in control of the REE uptake into the plant. Regional variations of the microbiological composition of the soils and probably not only a priori the bulk soil composition of the minerals in the soil are the cause of the regional variations making it possible to identify the geographic origin of pumpkin seeds and as a consequence the pumpkin seed oil.

Determination of benzo[a]pyrene in edible oils using phase-transfer-catalyst-assisted saponification and supramolecular solvent microextraction coupled to HPLC with fluorescence detection.

PubMed

Wang, Jin; Liu, Laping; Shi, Ludi; Yi, Tingquan; Wen, Yuxia; Wang, Juanli; Liu, Shuhui

2017-01-01

For the analysis of edible oils, saponification is well known as a useful method for eliminating oil matrices. The conventional approach is conducted with alcoholic alkali; it consumes a large volume of organic solvents and impedes the retrieval of analytes by microextraction. In this study, a low-organic-solvent-consuming method has been developed for the analysis of benzo[a]pyrene in edible oils by high-performance liquid chromatography with fluorescence detection. Sample treatment involves aqueous alkaline saponification, assisted by a phase-transfer catalyst, and selective in situ extraction of the analyte with a supramolecular solvent. Comparison of the chromatograms of the oil extracts obtained by different microextraction methods showed that the supramolecular solvent has a better clean-up effect for the unsaponifiable matter from oil matrices. The method offered excellent linearity over a range of 0.03- 5.0 ng mL -1 (r > 0.999). Recovery rates varied from 94 to 102% (RSDs <5.0%). The detection limit and quantification limit were 0.06 and 0.19 μg kg -1 , respectively. The proposed method was applied for the analysis of 52 edible oils collected online in China; the analyte contents of 23 tested oil samples exceeded the maximum limit of 2 μg kg -1 for benzo[a]pyrene set by the Commission Regulation of the European Union. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Role of Graduate Employee Unions in Gender Equality (abstract)

NASA Astrophysics Data System (ADS)

Murphy, Nicholas A.; Freeland, Emily

2009-04-01

Graduate employee unions represent a significant fraction of graduate employees in the United States, Canada, and other nations. The collective bargaining process is a unique forum where issues ranging from paid parental leave, hostile work environment, and access to lactation rooms can be addressed on an even footing with the employing universities. Because employment is governed by a collective bargaining agreement, violations are subject to a grievance policy. The Teaching Assistants' Association at the University of Wisconsin-Madison is one of the oldest graduate employee unions in the world. We discuss this example union, including successes in both the collective bargaining process and the grievance procedure. In particular, we find that graduate employee unions are an effective means of fighting pregnancy discrimination. We also provide a comparison of parental leave policies for graduate students at various universities.

Institutional pioneers in world politics: Regional institution building and the influence of the European Union.

PubMed

Lenz, Tobias; Burilkov, Alexandr

2017-09-01

What drives processes of institution building within regional international organizations? We challenge those established theories of regionalism, and of institutionalized cooperation more broadly, that treat different organizations as independent phenomena whose evolution is conditioned primarily by internal causal factors. Developing the basic premise of 'diffusion theory' - meaning that decision-making is interdependent across organizations - we argue that institutional pioneers, and specifically the European Union, shape regional institution-building processes in a number of discernible ways. We then hypothesize two pathways - active and passive - of European Union influence, and stipulate an endogenous capacity for institutional change as a key scope condition for their operation. Drawing on a new and original data set on the institutional design of 34 regional international organizations in the period from 1950 to 2010, the article finds that: (1) both the intensity of a regional international organization's structured interaction with the European Union (active influence) and the European Union's own level of delegation (passive influence) are associated with higher levels of delegation within other regional international organizations; (2) passive European Union influence exerts a larger overall substantive effect than active European Union influence does; and (3) these effects are strongest among those regional international organizations that are based on founding contracts containing open-ended commitments. These findings indicate that the creation and subsequent institutional evolution of the European Union has made a difference to the evolution of institutions in regional international organizations elsewhere, thereby suggesting that existing theories of regionalism are insufficiently able to account for processes of institution building in such contexts.

78 FR 38541 - Increase in Fees for Voluntary Federal Dairy Grading and Inspection Services

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-27

... 10 percent effective February 2014. The fees applicable to European Union Health Certification... European Union Health Certification Program derogation process. These actions will equally affect all...-resident service per European Union (EU) Health Certification Program derogation for somatic cell count and...

Maxillary post-traumatic outcome correction literature review and our experience. Part I: maxillary bone non-unions-"poor bone positioning".

PubMed

D'Agostino, A; Toffanetti, G; Scala, R; Trevisiol, L; Ferrari, F

2004-04-01

Still today, there is no classification of non-unions in maxillofacial traumatology. There is a broad spectrum of definitions that simultaneously describe the pathological conditions and functional implications determined by the anatomical location of the fractures and the time factor. In this article the authors describe a literature review about bone non-union classification. Weber, in 1973, introduced the term "pseudo-arthrosis" to describe an altered process of bone healing characterised by the presence of fibrous tissue interposed between the fracture segments, that was lined with cartilaginous tissue and joined by a capsule; Spiessl, in 1988, used the term "non-union" to define any alteration of the bone healing process after a time period of more than 6 months from the initial traumatic event; Rosen, in 1990, proposed a new classification of the modes of altered bone healing in fractures, distinguishing 5 categories: delayed consolidation, non-union, non-union vascular, non union avascular, pseudoarthrosis. The authors also talk about "poor bone positioning". This factor describes the incorrect anatomical position of the bone fragments despite perfectly normal healing according to Gruss. In this article they also discuss about the treatment of non-unions and the treatment of occlusal alterations caused by poor post-traumatic bone positioning.

European union regulatory developments for new vaccine adjuvants and delivery systems.

PubMed

Sesardic, Dorothea; Dobbelaer, Roland

2004-06-23

Interest in vaccine adjuvants and new delivery systems has grown rapidly over the past few years. New vaccine candidates have emerged, which, because of their poor immunogenicity, rely on adjuvants to improve their presentation and targeting and to potentiate their protective immune response. Better understandings of the mechanisms of action, together with logistic and economical considerations have resulted in an explosion of technologies. However, there have been few new registered products for human use, and antigens incorporated into immunostimulating reconstituted influenza virosomes have only relatively recently been licensed in European Union (EU) countries. Influenza vaccine, adjuvanted with water in oil emulsion containing squalene (adjuvant MF59C1) is now also approved. Although current EU regulations focus on traditional adjuvants, notably aluminium and calcium salts, advances have been made in regulatory considerations. The European agency for the evaluation of medicinal products, through its working parties, is actively drafting guidance on requirements for the evaluation of new adjuvants in vaccines. This paper summarises the new developments in EU regulatory aspects relevant to adjuvant quality at development stages, during the manufacturing process, and at the final bulk stage of adjuvant with antigen, and also summarises regulatory expectation regarding safety at pre-clinical and clinical stages. The paper highlights the regulatory concerns and existing bottlenecks that have led to slow approval of new technologies.

75 FR 80677 - The Low-Income Definition

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-23

... original regulatory text so it is consistent with the geo-coding software the agency uses to make the low... Union Act (Act) authorizes the NCUA Board (Board) to define ``low-income members'' so that credit unions... process of implementing geo- coding software to make the calculation automatically for credit unions...

77 FR 11171 - License Renewal Application for Callaway Plant, Unit 1, Union Electric Company

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-24

... Callaway Plant, Unit 1, Union Electric Company AGENCY: Nuclear Regulatory Commission. ACTION: Intent to prepare environmental impact statement and conduct scoping process. SUMMARY: Union Electric Company, a..., MO. The current operating license for Callaway expires on October 18, 2024. DATES: The public scoping...

TRANSACTIONS OF THE ALL-UNION CONFERENCE ON INFORMATION RETRIEVAL SYSTEMS AND AUTOMATED PROCESSING OF SCIENTIFIC AND TECHNICAL INFORMATION (3rd): PREFACE

DTIC Science & Technology

The research and development of information services within the USSR, reported at the 3rd All-Union Conference on information retrieval systems and automated processing of scientific and technical information, is discussed.

JPRS Report, China

DTIC Science & Technology

1987-12-31

inconsistent with Japan’s declared policy of opening up her markets. JPRS-CAR-87-061 31 December 1987 28 ECONOMIC 2. The "three lows "— low oil prices, the...intermediate- range warheads in Soviet Asia and the United States, respectively. But the United States and some Western European nations soon demanded...Union insisted on keeping 100 intermediate- range guided missiles in Asia while balking at the U.S. demand that it be allowed to deploy an equal

Quality and age of shallow groundwater in the Bakken Formation production area, Williston Basin, Montana and North Dakota.

PubMed

McMahon, P B; Caldwell, R R; Galloway, J M; Valder, J F; Hunt, A G

2015-04-01

The quality and age of shallow groundwater in the Bakken Formation production area were characterized using data from 30 randomly distributed domestic wells screened in the upper Fort Union Formation. Comparison of inorganic and organic chemical concentrations to health based drinking-water standards, correlation analysis of concentrations with oil and gas well locations, and isotopic data give no indication that energy-development activities affected groundwater quality. It is important, however, to consider these results in the context of groundwater age. Most samples were recharged before the early 1950s and had 14C ages ranging from <1000 to >30,000 years. Thus, domestic wells may not be as well suited for detecting contamination associated with recent surface spills as shallower wells screened near the water table. Old groundwater could be contaminated directly by recent subsurface leaks from imperfectly cemented oil and gas wells, but horizontal groundwater velocities calculated from 14C ages imply that the contaminants would still be less than 0.5 km from their source. For the wells sampled in this study, the median distance to the nearest oil and gas well was 4.6 km. Because of the slow velocities, a long-term commitment to groundwater monitoring in the upper Fort Union Formation is needed to assess the effects of energy development on groundwater quality. In conjunction with that effort, monitoring could be done closer to energy-development activities to increase the likelihood of early detection of groundwater contamination if it did occur. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Concentrations of dioxins and dioxin-like PCBs in feed materials in the Netherlands, 2001-11.

PubMed

Adamse, Paulien; Van der Fels-Klerx, H J Ine; Schoss, Stefanie; de Jong, Jacob; Hoogenboom, Ron L A P

2015-01-01

This study aimed to obtain insights into contamination of feed materials used in the Netherlands with dioxins (polychlorinated dibenzo-p-dioxins and dibenzofurans) and dioxin-like polychlorinated biphenyls (PCBs). Monitoring results from the period 2001-11, covering in total 4938 samples, were statistically analysed and evaluated against the statutory limits set at the beginning or during this period. The percentage of samples exceeding maximum levels set within the European Union for either dioxins or the sum of dioxins and dioxin-like PCBs were below 1% for most feed categories, except for fish meal (4.1%), clay minerals (binders and anti-caking agents) (3.4%), and vegetable oils and byproducts (1.7%). For most feed categories, non-compliance with the action threshold (roughly 33% lower than maximum levels) for either dioxins or dioxin-like PCBs was up to three times higher than non-compliance with the respective maximum levels. Exceedance of action thresholds was just above 1% for animal fat, pre-mixtures and feed materials of plant origin excluding vegetable oils. For the categories fish meal, clay minerals, and vegetable oils and byproducts, the action thresholds were exceeded by 5.0%, 9.8% and 3.0% of the samples, respectively. In general, the percentages of samples that exceeded the action thresholds and maximum levels were lower than those reported for the European Union by the European Food Safety Authority (EFSA). In most of the feed materials, there seems to be a decreasing trend in concentrations of dioxins or dioxin-like PCBs over the years. However, a lowering of the limits of quantification during this period and the low concentrations in most samples precludes drawing strong conclusions.

Production and application of a thermostable lipase from Serratia marcescens in detergent formulation and biodiesel production.

PubMed

García-Silvera, Edgar Edurman; Martínez-Morales, Fernando; Bertrand, Brandt; Morales-Guzmán, Daniel; Rosas-Galván, Nashbly Sarela; León-Rodríguez, Renato; Trejo-Hernández, María R

2018-03-01

In this study, extracellular lipase was produced by Serratia marcescens wild type and three mutant strains. The maximum lipase activity (80 U/mL) was obtained with the SMRG4 mutant strain using soybean oil. Using a 2 2 factorial design, the lipase production increased 1.55-fold (124 U/mL) with 4% and 0.05% of soybean oil and Triton X-100, respectively. The optimum conditions for maximum lipase activity were 50 °C and pH 8. However, the enzyme was active in a broad range of pH (6-10) and temperatures (5-55 °C). This lipase was stable in organic solvents and in the presence of oxidizing agents. The enzyme also proved to be efficient for the removal of triacylglycerol from olive oil in cotton cloth. A Box-Behnken experimental design was used to evaluate the effects of the interactions between total lipase activity, buffer pH, and wash temperatures on oil removal. The model obtained suggested that all selected factors had a significant impact on oil removal, with optimum conditions of 550 U lipase, 45 °C, pH 9.5, with 79.45% removal. Biotransformation of waste frying oil using the enzyme and in presence of methanol resulted in the synthesis of methyl esters such as methyl oleate, methyl palmitate, and methyl stearate. © 2017 International Union of Biochemistry and Molecular Biology, Inc.

29 CFR 452.61 - Elimination contests-local unions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 2 2011-07-01 2011-07-01 false Elimination contests-local unions. 452.61 Section 452.61... AND DISCLOSURE ACT OF 1959 Nominations for Office § 452.61 Elimination contests—local unions. (a) A procedure in a local under which nominees compete in an elimination process to reduce the number of...

29 CFR 452.61 - Elimination contests-local unions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 2 2010-07-01 2010-07-01 false Elimination contests-local unions. 452.61 Section 452.61... AND DISCLOSURE ACT OF 1959 Nominations for Office § 452.61 Elimination contests—local unions. (a) A procedure in a local under which nominees compete in an elimination process to reduce the number of...

Justice Perceptions of Union and Nonunion Employees within an Urban Technical College

ERIC Educational Resources Information Center

Vasquez, Marquoise D.

2013-01-01

Numerous studies exist on distributive and procedural justice among union represented or nonunion employees. However, there does not appear to be any research on the perceptions of justice from individuals who have worked in both capacities, under differing processes and procedures for each group, within the same heavily unionized organization.…

A mathematical model of fluid and gas flow in nanoporous media.

PubMed

Monteiro, Paulo J M; Rycroft, Chris H; Barenblatt, Grigory Isaakovich

2012-12-11

The mathematical modeling of the flow in nanoporous rocks (e.g., shales) becomes an important new branch of subterranean fluid mechanics. The classic approach that was successfully used in the construction of the technology to develop oil and gas deposits in the United States, Canada, and the Union of Soviet Socialist Republics becomes insufficient for deposits in shales. In the present article a mathematical model of the flow in nanoporous rocks is proposed. The model assumes the rock consists of two components: (i) a matrix, which is more or less an ordinary porous or fissurized-porous medium, and (ii) specific organic inclusions composed of kerogen. These inclusions may have substantial porosity but, due to the nanoscale of pores, tubes, and channels, have extremely low permeability on the order of a nanodarcy (~109-²¹ m² ) or less. These inclusions contain the majority of fluid: oil and gas. Our model is based on the hypothesis that the permeability of the inclusions substantially depends on the pressure gradient. At the beginning of the development of the deposit, boundary layers are formed at the boundaries of the low-permeable inclusions, where the permeability is strongly increased and intensive flow from inclusions to the matrix occurs. The resulting formulae for the production rate of the deposit are presented in explicit form. The formulae demonstrate that the production rate of deposits decays with time following a power law whose exponent lies between -1/2 and -1. Processing of experimental data obtained from various oil and gas deposits in shales demonstrated an instructive agreement with the prediction of the model.

Exploration and development offshore southern Vietnam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferguson, A.M.

1996-01-01

In Vietnam, the major focus of the oil and gas industry is on the Nam Con Son and Cuu Long Basins in the southern offshore area. Major licensing first occurred here in the early 1970s. Some exploration was also undertaken by foreign companies in the early 1980s. In 1981, the Soviet Union undertook to assist Vietnam with the development of oil and gas. Vietsovpetro, a joint venture between the then Soviet Oil and Gas Ministry and the Vietnam Oil and Gas Corporation was formed. Most of Vietsovpetro's efforts have been to develop the Bach Ho field in the Cuu Longmore » Basin. This now produces [approximately]130000 bopd. The most recent large scale licensing round occurred in 1992, and, at present, there are over thirty foreign companies active in these Basins' blocks . The first phase of exploration is ending and successes in the Nam Con Son Basin include the BP-led Lan Tay/Lan Do gas discoveries and Pedco's gas discoveries. Mitsubishi's and Petronas' oil discoveries in the Cuu Long Basin have attracted much attention also. The Dai Hung oil field (BHP-operated) has been producing since late 1994. Certain blocks are being appraised, and exploration work is also continuing. Areas of the Cuu Long Basin that were part of Vietsovpetro's acreage, but which may soon be re-licensed, have generated keen interest. The presence of an active upstream industry - exploring, appraising, developing and producing - indicates the emergence of Vietnam as an important East Asian oil and gas player.« less

Decreases in collision risk and derailments attributed to changing at-risk behavior process at Union Pacific.

DOT National Transportation Integrated Search

2009-09-01

Changing At-Risk Behavior (CAB) is a safety process that is being conducted at Union Pacifics San Antonio Service Unit (SASU) with the aim of improving road and yard safety. CAB is an example of a proactive safety risk-reduction method, called Cle...

Promising evidence of impact on road safety by changing at-risk behavior process at Union Pacific

DOT National Transportation Integrated Search

2008-06-01

Changing At-risk Behavior (CAB) is a safety process that is being conducted at Union Pacifics San Antonio Service Unit with the aim of improving locomotive cab safety related to constraining signals. CAB is an example of a risk reduction method th...

Preparative separation of α- and β-santalenes and (Z)-α- and (Z)-β-santalols using silver nitrate-impregnated silica gel medium pressure liquid chromatography and analysis of sandalwood oil.

PubMed

Daramwar, Pankaj P; Srivastava, Prabhakar Lal; Priyadarshini, Balaraman; Thulasiram, Hirekodathakallu V

2012-10-07

The major sesquiterpene constituents of East-Indian sandalwood oil (Z)-α- and (Z)-β-santalols have shown to be responsible for most of the biological activities and organoleptic properties of sandalwood oil. The work reported here describes the strategic use of medium pressure liquid chromatography (MPLC) for the separation of both α- and β-santalenes and (Z)-α- and (Z)-β-santalols. Silver nitrate impregnated silica gel was used as the stationary phase in MPLC for quantitative separation of α- and β-santalenes and (Z)-α- and (Z)-β-santalols with mobile phases hexane and dichloromethane, respectively. The purities of α-santalene and (Z)-α-santalol obtained were >96%; however, β-santalene and (Z)-β-santalol were obtained with their respective inseparable epi-isomers. Limits of quantification (LoQ) relative to the FID detector were measured for important sesquiterpene alcohols of heartwood oil of S. album using serial dilutions of the standard stock solutions and demonstrated that the quality of the commercial sandalwood oil can be assessed for the content of individual sesquiterpene alcohols regulated by Australian Standard (AS2112-2003), International Organization for Standardization ISO 3518:2002 (E) and European Union (E. U.).

The dynamic model on the impact of biodiesel blend mandate (B5) on Malaysian palm oil domestic demand: A preliminary finding

NASA Astrophysics Data System (ADS)

Abidin, Norhaslinda Zainal; Applanaidu, Shri-Dewi; Sapiri, Hasimah

2014-12-01

Over the last ten years, world biofuels production has increased dramatically. The biodiesel demand is driven by the increases in fossil fuel prices, government policy mandates, income from gross domestic product and population growth. In the European Union, biofuel consumption is mostly driven by blending mandates in both France and Germany. In the case of Malaysia, biodiesel has started to be exported since 2006. The B5 of 5% blend of palm oil based biodiesel into diesel in all government vehicles was implemented in February 2009 and it is expected to be implemented nationwide in the nearest time. How will the blend mandate will project growth in the domestic demand of palm oil in Malaysia? To analyze this issue, a system dynamics model was constructed to evaluate the impact of blend mandate implementation on the palm oil domestic demand influence. The base run of simulation analysis indicates that the trend of domestic demand will increase until 2030 in parallel with the implementation of 5 percent of biodiesel mandate. Finally, this study depicts that system dynamics is a useful tool to gain insight and to experiment with the impact of changes in blend mandate implementation on the future growth of Malaysian palm oil domestic demand sector.

Nutrigenomics of extra-virgin olive oil: A review.

PubMed

Piroddi, Marta; Albini, Adriana; Fabiani, Roberto; Giovannelli, Lisa; Luceri, Cristina; Natella, Fausta; Rosignoli, Patrizia; Rossi, Teresa; Taticchi, Agnese; Servili, Maurizio; Galli, Francesco

2017-01-02

Nutrigenomics data on the functional components of olive oil are still sparse, but rapidly increasing. Olive oil is the main source of fat and health-promoting component of the Mediterranean diet. Positive effects have been observed on genes involved in the pathobiology of most prevalent age- and lifestyle-related human conditions, such as cancer, cardiovascular disease and neurodegeneration. Other effects on health-promoting genes have been identified for bioactive components of olives and olive leafs. Omics technologies are offering unique opportunities to identify nutritional and health biomarkers associated with these gene responses, the use of which in personalized and even predictive protocols of investigation, is a main breakthrough in modern medicine and nutrition. Gene regulation properties of the functional components of olive oil, such as oleic acid, biophenols and vitamin E, point to a role for these molecules as natural homeostatic and even hormetic factors with applications as prevention agents in conditions of premature and pathologic aging. Therapeutic applications can be foreseen in conditions of chronic inflammation, and particularly in cancer, which will be discussed in detail in this review paper as major clinical target of nutritional interventions with olive oil and its functional components. © 2016 BioFactors, 43(1):17-41, 2017. © 2016 International Union of Biochemistry and Molecular Biology.

Quantitative analysis and health risk assessment of polycyclic aromatic hydrocarbons in edible vegetable oils marketed in Shandong of China.

PubMed

Jiang, Dafeng; Xin, Chenglong; Li, Wei; Chen, Jindong; Li, Fenghua; Chu, Zunhua; Xiao, Peirui; Shao, Lijun

2015-09-01

This work studies on the quantitative analysis and health risk assessment of polycyclic aromatic hydrocarbons (PAHs) in edible vegetable oils in Shandong, China. The concentrations of 15 PAHs in 242 samples were determined by high performance liquid chromatography coupled with fluorescence detection. The results indicated that the mean concentration of 15 PAHs in oil samples was 54.37 μg kg(-1). Low molecular weight PAH compounds were the predominant contamination. Especially, the carcinogenic benzo(a)pyrene (BaP) was detected at a mean concentration of 1.28 μg kg(-1), which was lower than the limit of European Union and China. A preliminary evaluation of human health risk assessment for PAHs was accomplished using BaP toxic equivalency factors and the incremental lifetime cancer risk (ILCR). The ILCR values for children, adolescents, adults, and seniors were all larger than 1 × 10(-6), indicating a high potential carcinogenic risk on the dietary exposed populations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Functional assessment of plant and microalgal lipid pathway genes in yeast to enhance microbial industrial oil production.

PubMed

Peng, Huadong; Moghaddam, Lalehvash; Brinin, Anthony; Williams, Brett; Mundree, Sagadevan; Haritos, Victoria S

2018-03-01

As promising alternatives to fossil-derived oils, microbial lipids are important as industrial feedstocks for biofuels and oleochemicals. Our broad aim is to increase lipid content in oleaginous yeast through expression of lipid accumulation genes and use Saccharomyces cerevisiae to functionally assess genes obtained from oil-producing plants and microalgae. Lipid accumulation genes DGAT (diacylglycerol acyltransferase), PDAT (phospholipid: diacylglycerol acyltransferase), and ROD1 (phosphatidylcholine: diacylglycerol choline-phosphotransferase) were separately expressed in yeast and lipid production measured by fluorescence, solvent extraction, thin layer chromatography, and gas chromatography (GC) of fatty acid methyl esters. Expression of DGAT1 from Arabidopsis thaliana effectively increased total fatty acids by 1.81-fold above control, and ROD1 led to increased unsaturated fatty acid content of yeast lipid. The functional assessment approach enabled the fast selection of candidate genes for metabolic engineering of yeast for production of lipid feedstocks. © 2017 International Union of Biochemistry and Molecular Biology, Inc.

JPRS Report, Soviet Union, The Working Class & the Contemporary World, No. 2, March-April 1987.

DTIC Science & Technology

1987-08-19

entire business district. Public transport did not operate. The streets 19 were packed with strikers, sympathizers and lookers-on. A strike was... transport , the oil business and so forth. Reflecting this expansion, the U.S. Steel corporation changed its name in mid- 1986. It is now called USX...work home. Yet owing to the vastness of the territories of industrial cities and the insufficient development of public transport and its expense

Russia and the European Union: The Sources and Limits of Special Relationships

DTIC Science & Technology

2007-02-01

Russia, 2002, 2003, 2005. 43. EBRD Transition Reports; and Cynthia Roberts and Thomas Sherlock , “Bringing the Russian State Back In,” Comparative...April 2006, pp. 69-82, at p. 69. 104 146. Chris Holmes , “Atlantic Basin, Mideast Adequate to Supply Europe, US in Mid-Term,” Oil and Gas Journal’s...Limits of Partial Integration.” Aktualnye problemy Evropy (Urgent Problems of Europe). Vol. 4, 2004, pp. 87-113. _______ and Thomas Sherlock

The Columbia River and Tributaries Study, Interim Report, Yakima-Union Gap Flood Damage Reduction, Yakima River Basin, Washington.

DTIC Science & Technology

1980-03-01

Populus trichoearp& Shrubs Red osier dogwood Cornus stolonifera Willows Salix spp. C Elderberry Sambucus glauca C Serviceberry Amelanchier alnifolia C...Taraxucum off icinale C Madowlrue Thalictrum occidentale C Ceow prni Heracleum lanatun C Monkey flower Iiis langsdorf sii C Rocky Mountain irishi mssuins...aboaeem oil the significant aree.Ioloical resources is the project aea TO the centrary nearby are suggest that important material OWwall be loated to the

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, H.P.

The Cove Fort-Sulphurdale Known Geothermal Resource Area (KGRA) is located near the junction of the Pavant Range and the Tushar Mountains in south-central Utah. The area has been the site of an intensive geothermal exploration effort since 1975. The electrical resistivity data obtained by Union Oil Company and a subsequent survey conducted for the Earth Science Laboratory and a detailed numerical interpretation of both data sets are presented. The detailed modeling permits a characterization of the intrinsic electrical resistivity to depths exceeding 2000 feet. An area of over two square miles with bulk in-situ resistivities of four-to-five ohm-m is delineatedmore » at Sulphurdale near the Union Oil Co. well CFSU No. 42-7. The low-resistivities rocks define the area of extensive hydrothermal alteration in response to the presence of clay minerals and conductive thermal fluids. In contrast the area north and east of Cove Fort is typified by high (100-300 ohm-m) resistivities to depths exceeding 2000 feet. This is an area of Cretaceous and Paleozoic sedimentary rocks where two attempts to drill to reservoir depth failed because of extreme drilling problems. The high resistivities are not considered encouraging for the presence of a deeper reservoir. The electrical resistivity interpretation has defined several areas of probable upward migration of thermal fluids along north-trending normal faults. Some of these areas may have potential for direct heat geothermal utilization.« less

Union-Management Cooperation: A Process for Increasing Worker Autonomy and Improving Work Group Effectiveness.

ERIC Educational Resources Information Center

Kroll, Philip R.; And Others

Limited research has been conducted on the direct and indirect impact of union-management cooperation (UMC) programs on worker autonomy, work group effectiveness, and worker satisfaction. For this study, a research questionnaire designed to explore these relationships was mailed to four Ohio unions and was returned by 339 members. Workers at…

Preparation for Bargaining: Negotiation and Administration of the Contract.

ERIC Educational Resources Information Center

Higginbotham, Richard L.

Every state will soon have some negotiation law covering school employees. If negotiation is an adversary process between two powers, then there has to be a balance of power between the school board and union. Today unions have more actual and potential power than school management. Unions spend great sums of money preparing for negotiations and…

HEALTH AND SAFETY ORGANIZING: OCAW’S WORKER-TO-WORKER HEALTH AND SAFETY TRAINING PROGRAM*

PubMed Central

SLATIN, CRAIG

2018-01-01

In 1987, the Oil, Chemical, and Atomic Workers International Union (OCAW) was funded as one of the original eleven awardees of the Superfund Worker Training Program of the National Institute of Environmental Health Sciences. The OCAW, with the Labor Institute, developed a hazardous waste worker and hazardous materials emergency responder health and safety training program that was specific to its members in the represented industries. A social history is developed to explore a union-led, worker health education intervention. The program sought to develop worker-trainers who would conduct the training, using the Small-Group Activity Method, participate in curriculum development, and ultimately use health and safety training as a vehicle for identifying, developing, and mobilizing health and safety activists among the membership. Although the direction for this effort came from progressive leadership, it arose from the political economy of labor/management relations within specific industrial sectors. PMID:17208754

Management of tibial non-unions according to a novel treatment algorithm.

PubMed

Ferreira, Nando; Marais, Leonard Charles

2015-12-01

Tibial non-unions represent a spectrum of conditions that are challenging to treat. The optimal management remains unclear despite the frequency with which these diagnoses are encountered. The aim of this study was to determine the outcome of tibial non-unions managed according to a novel tibial non-union treatment algorithm. One hundred and eighteen consecutive patients with 122 uninfected tibial non-unions were treated according to our proposed tibial non-union treatment algorithm. All patients were followed-up clinically and radiologically for a minimum of six months after external fixator removal. Four patients were excluded because they did not complete the intended treatment process. The final study population consisted of 94 men and 24 women with a mean age of 34 years. Sixty-seven non-unions were stiff hypertrophic, 32 mobile atrophic, 16 mobile oligotrophic and one true pseudoarthrosis. Six non-unions were classified as type B1 defect non-unions. Bony union was achieved after the initial surgery in 113/122 (92.6%) tibias. Nine patients had failure of treatment. Seven persistent non-unions were successfully retreated according to the tibial non-union treatment algorithm. This resulted in final bony union in 120/122 (98.3%) tibias. The proposed tibial non-union treatment algorithm appears to produce high union rates across a diverse group of tibial non-unions. Tibial non-unions however, remain difficult to treat and should be referred to specialist units where advanced reconstructive techniques are practiced on a regular basis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Final report of coordination and cooperation with the European Union on embankment failure analysis

USDA-ARS?s Scientific Manuscript database

There has been an emphasis in the European Union (EU) community on the investigation of extreme flood processes and the uncertainties related to these processes. Over a 3-year period, the EU and the U.S. dam safety community (1) coordinated their efforts and collected information needed to integrate...

Improved safety culture and labor-management relations attributed to changing at-risk behavior process at Union Pacific.

DOT National Transportation Integrated Search

2009-09-01

Changing At-Risk Behavior (CAB) is a safety process that is being conducted at Union Pacifics San Antonio Service Unit (SASU) with the aim of improving road and yard safety. CAB is an example of a proactive safety risk-reduction method called Clea...

Languages and Institutions in the European Union. Mercator Working Papers.

ERIC Educational Resources Information Center

Alcaraz, Manuel

This paper situates languages in the framework of European construction, analyzing problems resulting from the definition of languages' official status in the European Union (EU) juridical system. It explains that the process of European construction is historically defined by means of two distinct features (it is an open process, and at the same…

Impact of software and hardware technologies on occupational health and safety policies in Saudi Arabian oil refineries.

PubMed

Idreis, Hany M; Siqueira, Carlos E; Levenstein, Charles C

2006-01-01

This article seeks to examine the impact of technology importation on occupational health and safety in both Saudi Arabian and U.S. oil refining industries. Technologies imported to the Saudi oil industry take two forms: hardware (sophisticated equipment to run oil facilities) and software (policies and regulations pertaining to workers' health and safety, and employment rights installed by Aramco's founding multinational companies). This study utilizes qualitative, historically oriented, cross-national case studies to compare and assess workers' health, safety, and rights in Saudi Aramco with its U.S. counterpart, Motiva Enterprises. Two facilities were chosen to conduct field research: the Saudi Aramco oil refinery at Jeddah and Motiva's refinery at Port Arthur, Texas. The Jeddah refinery is fully owned by Saudi Aramco, thus, representing Aramco's health and safety policies and regulations. The Port Arthur refinery serves as a reference case study for U.S. oil refining facilities. The aspects of occupational health and safety in Saudi Aramco--ExxonMobil's joint ventures SAMREF and LUBREF--also are discussed to examine workers' health policies in both companies. The American oil industry made a significant contribution in establishing the Saudi oil industry, with the cooperation of the Saudi government. Despite having outstanding employment benefits schemes in Saudi Aramco, the presence of an organized work force better serves employee participation in Motiva than in Aramco. Safety systems such as Process Safety Management (PSM)--applied in Motiva--partially exist in Aramco to operate hardware technologies safely. Motiva training systems are better through PACE's Triangle of Prevention (TOP). Both companies follow the same pattern of handling occupational injuries and diseases; however, Saudi government agencies (GOSI) are responsible for compensating and treating injured workers. Saudi workers expressed conditional support for the worker committee program proposed by the Ministry of Labor. American and Saudi workers are concerned about the quality and sufficiency of health and safety training, employment promotion, work pressure, and job uncertainty due to continuous downsizing. This article recommends that Saudi social actors increase safety and health awareness in the work environment by providing intensive occupational safety training to the employees (as demanded by Saudi and American workers), improve labor-management relations through establishing strong cooperative contacts with regional and international trade unions, and establish uniform and standard occupational health and safety regulations for Saudi Aramco and its subsidiaries in order to provide an equal level of protection for Saudi workers.

Institutional pioneers in world politics: Regional institution building and the influence of the European Union

PubMed Central

Lenz, Tobias; Burilkov, Alexandr

2016-01-01

What drives processes of institution building within regional international organizations? We challenge those established theories of regionalism, and of institutionalized cooperation more broadly, that treat different organizations as independent phenomena whose evolution is conditioned primarily by internal causal factors. Developing the basic premise of ‘diffusion theory’ — meaning that decision-making is interdependent across organizations — we argue that institutional pioneers, and specifically the European Union, shape regional institution-building processes in a number of discernible ways. We then hypothesize two pathways — active and passive — of European Union influence, and stipulate an endogenous capacity for institutional change as a key scope condition for their operation. Drawing on a new and original data set on the institutional design of 34 regional international organizations in the period from 1950 to 2010, the article finds that: (1) both the intensity of a regional international organization’s structured interaction with the European Union (active influence) and the European Union’s own level of delegation (passive influence) are associated with higher levels of delegation within other regional international organizations; (2) passive European Union influence exerts a larger overall substantive effect than active European Union influence does; and (3) these effects are strongest among those regional international organizations that are based on founding contracts containing open-ended commitments. These findings indicate that the creation and subsequent institutional evolution of the European Union has made a difference to the evolution of institutions in regional international organizations elsewhere, thereby suggesting that existing theories of regionalism are insufficiently able to account for processes of institution building in such contexts. PMID:29400350

Huddling with the honchos in Havana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendelsohn, J.

1993-09-01

The economic collapse following the Soviet Union's disintegration has affected all aspects of life in Cuba. In this paper Cuban foreign policy and defense is discussed. This article evaluates the energy situation of Cuba (oil imports), food shortages, Cuba's position on the Treaty of Tlatelolco (formally, the Treaty for the Prohibition of Nuclear Weapons in Latin America), Cuba's nuclear power projects, and discussions concerning Cuban involvement in biological warfare. The effects of U.S. military activities on U.S.-Cuban relations are emphasized. 8 refs.

Installation Restoration Program. Phase I. Records Search. Seymour Johnson Air Force Base, North Carolina.

DTIC Science & Technology

1982-07-01

and waste treatment pilot plants . Developed odor control program which suc- cessfully reduced odor emissions and represented Union Carbide at a public...the runway where oil and grease has been detected as well as the discharge from the City of Goldsboro waste- water treatment plant which occurs within...There are no known threatened or en- dangered plant species on base. The only endangered animal species which may potentially inhabit the base is the Red

United States Policy Options in the Western Indian Ocean.

DTIC Science & Technology

1982-06-01

Into this new arena rushed the superpowers of the 19 709: the United States, the Soviet Union, and China. Economic factors were partly responsible ...area, and rising fear about the safe navigation of oil vessels from the PG the U.S. response in the area has increased. U.S. naval activity in the 10...development has been made more difficult by the country’ s terrain and its isolation from external markets . These factors when added to the poor

Scientists Focus on Land Subsidence Impacts on Coastal and Delta Cities

NASA Astrophysics Data System (ADS)

Showstack, Randy

2014-05-01

Some coastal and delta cities around the world are sinking but not necessarily due only to sea level rise and impacts from extreme weather events. Land subsidence that is caused by anthropogenic processes—including the extraction of groundwater, oil, and gas and the drainage of soils—is a significant concern for Jakarta, Indonesia; Manila, Philippines; New Orleans, La.; and many other coastal and delta cities, according to scientists at a 28 April briefing held at the European Geosciences Union's General Assembly in Vienna, Austria.

The Economic Consequences of an Invasion of Poland by the Soviet Union.

DTIC Science & Technology

1981-09-01

worker’s salary. Basic food supplies are erratic. Travelers report that at Gorsky, for example, there is no butter, meat, fruit and flour , and that...Lithuanians, Ukranians, Estonians, Georgians, Armenians, Uzbeks and many of the Muslim peoples. One author noted, "With the glue of belief and trust...Forecast," Wall Street Journal , May 18, 1981, p. 31. 56. Daniel Park, "Oil and Gas in Comecon Countries," (London: Kogan Page, 1979) table 24a, p. 41

Stimulation results in the Giddings (Austin Chalk) field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meehan, D.N.

1995-05-01

So called ``water-fracs`` have obtained excellent results in the Austin Chalk formation of Giddings field. This inexpensive treatment uses high volumes of water but no proppant. The reasons the treatment is successful include imbibition, gravity drainage, skin damage removal, and repressurization of the reservoir to enhance recovery. Union Pacific Resources Co. (UPRC) has treated about 250 vertical and 150 horizontal wells with very high economic success rates. Incremental recoveries from horizontal well water fracs alone exceed 5 million bbl of oil equivalent (6 Mcf = 1 bbl).

Exploration and development offshore southern Vietnam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferguson, A.M.

1996-12-31

In Vietnam, the major focus of the oil and gas industry is on the Nam Con Son and Cuu Long Basins in the southern offshore area. Major licensing first occurred here in the early 1970s. Some exploration was also undertaken by foreign companies in the early 1980s. In 1981, the Soviet Union undertook to assist Vietnam with the development of oil and gas. Vietsovpetro, a joint venture between the then Soviet Oil and Gas Ministry and the Vietnam Oil and Gas Corporation was formed. Most of Vietsovpetro`s efforts have been to develop the Bach Ho field in the Cuu Longmore » Basin. This now produces {approximately}130000 bopd. The most recent large scale licensing round occurred in 1992, and, at present, there are over thirty foreign companies active in these Basins` blocks . The first phase of exploration is ending and successes in the Nam Con Son Basin include the BP-led Lan Tay/Lan Do gas discoveries and Pedco`s gas discoveries. Mitsubishi`s and Petronas` oil discoveries in the Cuu Long Basin have attracted much attention also. The Dai Hung oil field (BHP-operated) has been producing since late 1994. Certain blocks are being appraised, and exploration work is also continuing. Areas of the Cuu Long Basin that were part of Vietsovpetro`s acreage, but which may soon be re-licensed, have generated keen interest. The presence of an active upstream industry - exploring, appraising, developing and producing - indicates the emergence of Vietnam as an important East Asian oil and gas player.« less

Review of data on the dermal penetration of mineral oils and waxes used in cosmetic applications.

PubMed

Petry, T; Bury, D; Fautz, R; Hauser, M; Huber, B; Markowetz, A; Mishra, S; Rettinger, K; Schuh, W; Teichert, T

2017-10-05

Mineral oils and waxes used in cosmetic products, also referred to as "personal care products" outside the European Union, are mixtures of predominantly saturated hydrocarbons consisting of straight-chain, branched and ring structures with carbon chain lengths greater than C16. They are used in skin and lip care cosmetic products due to their excellent skin tolerance as well as their high protecting and cleansing performance and broad viscosity options. Recently, concerns have been raised regarding potential adverse health effects of mineral oils and waxes from dermal application of cosmetics. In order to be able to assess the risk for the consumer the dermal penetration potential of these ingredients has to be evaluated. The scope and objective of this review are to identify and summarize publicly available literature on the dermal penetration of mineral oils and waxes as used in cosmetic products. For this purpose, a comprehensive literature search was conducted. A total of 13 in vivo (human, animal) and in vitro studies investigating the dermal penetration of mineral oils and waxes has been identified and analysed. The majority of the substances were dermally adsorbed to the stratum corneum and only a minor fraction reached deeper skin layers. Overall, there is no evidence from the various studies that mineral oils and waxes are percutaneously absorbed and become systemically available. Thus, given the absence of dermal uptake, mineral oils and waxes as used in cosmetic products do not present a risk to the health of the consumer. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

An Oil/Water disperser device for use in an oil content Monitor/Control system

NASA Astrophysics Data System (ADS)

Kempel, F. D.

1985-07-01

This patent application discloses an oil content monitor/control unit system, including an oil/water disperser device, which is configured to automatically monitor and control processed effluent from an associated oil/water separator so that if the processed effluent exceeds predetermine in-port or at-sea oil concentration lmits, it is either recirculated to an associated oil/water separator via a ship's bilge for additional processing, or diverted to a holding tank for storage. On the other hand, if the oil concentration of the processed effluent is less than predetermine in-port or at-sea limits, it is discharged overboard. The oil/water disperser device is configured to break up any oil present in the processed effluent into uniform droplets for more accurate sensing of the oil present in the processed effluent into uniform droplets for more accurate sensing of the oil-in-water concentration level thereof. The oil/water disperser device has a flow-actuated variable orifice configured into a spring-loaded polyethylene plunger which provides the uniform distribution of oil droplets.

Source rock potential in Pakistan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raza, H.A.

1991-03-01

Pakistan contains two sedimentary basins: Indus in the east and Balochistan in the west. The Indus basin has received sediments from precambrian until Recent, albeit with breaks. It has been producing hydrocarbons since 1914 from three main producing regions, namely, the Potwar, Sulaisman, and Kirthar. In the Potwar, oil has been discovered in Cambrian, Permian, Jurassic, and Tertiary rocks. Potential source rocks are identified in Infra-Cambrian, Permian, Paleocene, and Eocene successions, but Paleocene/Eocene Patala Formation seems to be the main source of most of the oil. In the Sulaiman, gas has been found in Cretaceous and Tertiary; condensate in Cretaceousmore » rocks. Potential source rocks are indicated in Cretaceous, Paleocene, and Eocene successions. The Sembar Formation of Early Cretaceous age appears to be the source of gas. In the Kirthar, oil and gas have been discovered in Cretaceous and gas has been discovered in paleocene and Eocene rocks. Potential source rocks are identified in Kirthar and Ghazij formations of Eocene age in the western part. However, in the easter oil- and gas-producing Badin platform area, Union Texas has recognized the Sembar Formation of Early Cretaceous age as the only source of Cretaceous oil and gas. The Balochistan basin is part of an Early Tertiary arc-trench system. The basin is inadequately explored, and there is no oil or gas discovery so far. However, potential source rocks have been identified in Eocene, Oligocene, Miocene, and Pliocene successions based on geochemical analysis of surface samples. Mud volcanoes are present.« less

A MODIS-based analysis of the Val d'Agri Oil Center (South of Italy) thermal emission: an independent gas flaring estimation strategy

NASA Astrophysics Data System (ADS)

Pergola, Nicola; Faruolo, Mariapia; Irina, Coviello; Carolina, Filizzola; Teodosio, Lacava; Valerio, Tramutoli

2014-05-01

Different kinds of atmospheric pollution affect human health and the environment at local and global scale. The petroleum industry represents one of the most important environmental pollution sources, accounting for about 18% of well-to-wheels greenhouse gas (GHG) emissions. The main pollution source is represented by the flaring of gas, one of the most challenging energy and environmental problems facing the world today. The World Bank has estimated that 150 billion cubic meters of natural gas are being flared annually, that is equivalent to 30% of the European Union's gas consumption. Since 2002, satellite-based methodologies have shown their capability in providing independent and reliable estimation of gas flaring emissions, at both national and global scale. In this paper, for the first time, the potential of satellite data in estimating gas flaring volumes emitted from a single on-shore crude oil pre-treatment plant, i.e. the Ente Nazionale Idrocarburi (ENI) Val d'Agri Oil Center (COVA), located in the Basilicata Region (South of Italy), was assessed. Specifically, thirteen years of night-time Moderate Resolution Imaging Spectroradiometer (MODIS) data acquired in the medium and thermal infrared (MIR and TIR, respectively) bands were processed. The Robust Satellite Techniques (RST) approach was implemented for identifying anomalous values of the signals under investigation (i.e. the MIR-TIR difference one), associated to the COVA flares emergency discharges. Then, the Fire Radiative Power (FRP), computed for the thermal anomalies previously identified, was correlated to the emitted gas flaring volumes, available for the COVA in the period 2003 - 2009, defining a satellite based regression model for estimating COVA gas flaring emitted volumes. The used strategy and the preliminary results of this analysis will be described in detail in this work.

Obama address touches on research, energy, and environmental issues

NASA Astrophysics Data System (ADS)

Showstack, Randy

2012-02-01

President Barack Obama's State of the Union message, delivered on 24 January, touched on the need for basic research, energy production, support for clean energy, and environmental protection, but it included just one passing reference to climate change. In addition, the speech made no note of the Administration's recent denial of a controversial application for the Keystone XL pipeline to transport crude oil from Canada to the United States and made just an elliptical reference regarding the bankrupt Solyndra Corporation, which the administration had touted as a clean energy company. Innovation "demands basic research," Obama said, adding that Congress should not "gut these investments in our budget." Noting that one promise for innovation is American-made energy, Obama said he is directing the administration to "open more than 75% of our potential offshore oil and gas resources."

Oil on the water: Government regulation of a carcinogen in the twentieth-century Lancashire cotton spinning industry.

PubMed

Higgins, David; Tweedale, Geoffrey

2010-01-01

In the Lancashire cotton textile industry, mule spinners were prone to a chronic and sometimes fatal skin cancer (often affecting the groin). The disease had reached epidemic proportions by the 1920s, which necessitated action by the government, employers, and trade unions. In contrast to previous accounts, this article focuses on the government's reaction to mule spinners' cancer. Using official records in the National Archives, the slow introduction of health and safety measures by the government is explored in detail. Although obstructionism by the employers played a key role, one of the reasons for government inaction was the ambiguity of scientific research on engineering oils. On the other hand, prolonged scientific research suited a government policy that was framed around self regulation - a policy that had proved largely ineffective by the 1950s.

Wet separation processes as method to separate limestone and oil shale

NASA Astrophysics Data System (ADS)

Nurme, Martin; Karu, Veiko

2015-04-01

Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

Invited review: Essential oils as modifiers of rumen microbial fermentation.

PubMed

Calsamiglia, S; Busquet, M; Cardozo, P W; Castillejos, L; Ferret, A

2007-06-01

Microorganisms in the rumen degrade nutrients to produce volatile fatty acids and synthesize microbial protein as an energy and protein supply for the ruminant, respectively. However, this fermentation process has energy (losses of methane) and protein (losses of ammonia N) inefficiencies that may limit production performance and contribute to the release of pollutants to the environment. Antibiotic ionophores have been very successful in reducing these energy and protein losses in the rumen, but the use of antibiotics in animal feeds is facing reduced social acceptance, and their use has been banned in the European Union since January 2006. For this reason, scientists have become interested in evaluating other alternatives to control specific microbial populations to modulate rumen fermentation. Essential oils can interact with microbial cell membranes and inhibit the growth of some gram-positive and gram-negative bacteria. As a result of such inhibition, the addition of some plant extracts to the rumen results in an inhibition of deamination and methanogenesis, resulting in lower ammonia N, methane, and acetate, and in higher propionate and butyrate concentrations. Results have indicated that garlic oil, cinnamaldehyde (the main active component of cinnamon oil), eugenol (the main active component of the clove bud), capsaicin (the active component of hot peppers), and anise oil, among others, may increase propionate production, reduce acetate or methane production, and modify proteolysis, peptidolysis, or deamination in the rumen. However, the effects of some of these essential oils are pH and diet dependent, and their use may be beneficial only under specific conditions and production systems. For example, capsaicin appears to have small effects in high-forage diets, whereas the changes observed in high-concentrate diets (increases in dry matter intake and total VFA, and reduction in the acetateto-propionate ratio and ammonia N concentration) may be beneficial. Because plant extracts may act at different levels in the carbohydrate and protein degradation pathways, their careful selection and combination may provide a useful tool to manipulate rumen microbial fermentation effectively. However, additional research is required to establish the optimal dose in vivo in units of the active component, to consider the potential adaptation of microbial populations to their activities, to examine the presence of residues in the products (milk or meat), and to demonstrate improvements in animal performance.

Blood Versus Land: The Comparative Foundations for Citizenship and Voting Rights in Germany and Sweden

DTIC Science & Technology

2010-03-01

the political process. This thesis will examine how two major immigrant destination states within the European Union extend voting rights to...PAGES 77 14. SUBJECT TERMS Germany, Sweden, European Union , Voting rights, Franchise, Citizenship, Immigration, Immigrant, Migration, Nationalism 16...within the European Union extend voting rights to immigrants from outside the EU. These will be Germany and Sweden. The thesis concludes that the

Education and the Transition to Fatherhood: The Role of Selection Into Union.

PubMed

Trimarchi, Alessandra; Van Bavel, Jan

2017-02-01

Although advanced education has been found to be consistently associated with a later transition to parenthood for women, findings about education and the transition to parenthood have been much less consistent for men, and no stylized fact has emerged from the literature. We argue that the inconsistency of findings for men is due to the fact that the selection process involved in union formation has been disregarded in earlier studies. We hypothesize that men's educational attainment consistently and positively affects the transition to fatherhood via higher rates of union formation. We apply multiprocess event-history analysis to data from the Generations and Gender Surveys for 10 European countries. Our results show indeed a consistent positive effect of education on the transition to fatherhood, but it operates chiefly through selection into union. Failing to account for this selection process leads to a major underestimation of the salience of education for the transition to fatherhood.

Study on antimicrobial potential of neem oil nanoemulsion against Pseudomonas aeruginosa infection in Labeo rohita.

PubMed

Mishra, Prabhakar; R S, Suresh Kumar; Jerobin, Jayakumar; Thomas, John; Mukherjee, Amitava; Chandrasekaran, Natarajan

2014-01-01

Presence of several biochemical constituents in neem makes it an efficient antimicrobial agent for pathogenic diseases. The current investigation was aimed to assess the therapeutic potential of neem nanoemulsion as a control measure for Pseudomonas aeruginosa infection in freshwater fish Labeo rohita. The median lethal concentration (LC50) for the neem oil and neem nanoemulsion was 73.9 and 160.3 mg/L, respectively. The biomarker enzymes of treated fish tissues showed a significant difference in the level of glutathione reductase, catalase, and lipid peroxidation in neem oil-treated samples than in neem nanoemulsion-treated samples at P<0.05. The results were corroborative with histopathology and ultrastructural analysis. The bacterial infection of P. aeruginosa treated using neem nanoemulsion was more effective in both in vitro and in vivo methods. Present findings suggest that neem-based nanoemulsion has negligible toxicity to Rohu fishes. This makes neem-based nanoemulsion as an efficient therapeutic agent against P. aeruginosa infection, leading to its possible usage in the aquaculture industry. © 2014 International Union of Biochemistry and Molecular Biology, Inc.

Stimulating the biosynthesis of antroquinonol by addition of effectors and soybean oil in submerged fermentation of Antrodia camphorata.

PubMed

Hu, Yong-Dan; Lu, Rui-Qiu; Liao, Xiang-Ru; Zhang, Bo-Bo; Xu, Gan-Rong

2016-05-01

Antrodia camphorata is a precious medicinal mushroom that has attracted increasing attentions. Antroquinonol has been considered as being among the most biologically active components of A. camphorata. However, it was hardly biosynthesized via conventional submerged fermentation. Two approaches were applied to stimulate the biosynthesis of antroquinonol in submerged fermentation. On one hand, different kinds of effectors that may involve in the antroquinonol biosynthesis were investigated. Among the tested effectors, camphorwood leach liquor was the most effective for stimulating the antroquinonol production. On the other hand, because of the hydrophobic characteristics of antroquinonol, soybean oil was added to establish an extractive fermentation system for alleviating the product inhibition and resulting in enhanced productivity. The highest antroquinonol concentration could be achieved at 89.06 ± 0.14 mg/L when 10% (v/v) soybean oil was added at the beginning of the fermentation. This study will be of great significance for the study of A. camphorata and the bioprocess regulation of antroquinonol production. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

Treatment of industrial effluent water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levitskii, Yu.N.

1982-09-01

This article reports on a thematic exhibition on ''New Developments in Treatment of Natural and Effluent Water'' in the Sanitary-Technical Construction Section at the Exhibition of Achievements of the National Economy of the USSR. The exhibition acquainted visitors with the achievements of leading organizations in different branches of industry with respect to treatment of natural and industrial effluent water. The Kharkov ''Vodkanalproekt'' Institute and the Kharkov affiliate of the All-Union Scientific-Research Institute of Water and Geodesy has jointly developed a ''Polymer-25'' filter for removal of oil products from nonexplosive effluent water discharged by machine building plants. A Baku affiliate hasmore » developed a new ShFP-1 screw-type press filter for dewatering the sediments from water treatment plants as well as for sediments from chemical, food, and other types of plants. The State Institute for Applied Chemistry has designed a continuous process plant for treating effluent water and removing toxic organic waste by converting them into mineral salts with high efficiency.« less

Optimization of Refining Craft for Vegetable Insulating Oil

NASA Astrophysics Data System (ADS)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Process for converting heavy oil deposited on coal to distillable oil in a low severity process

DOEpatents

Ignasiak, Teresa; Strausz, Otto; Ignasiak, Boleslaw; Janiak, Jerzy; Pawlak, Wanda; Szymocha, Kazimierz; Turak, Ali A.

1994-01-01

A process for removing oil from coal fines that have been agglomerated or blended with heavy oil comprises the steps of heating the coal fines to temperatures over 350.degree. C. up to 450.degree. C. in an inert atmosphere, such as steam or nitrogen, to convert some of the heavy oil to lighter, and distilling and collecting the lighter oils. The pressure at which the process is carried out can be from atmospheric to 100 atmospheres. A hydrogen donor can be added to the oil prior to deposition on the coal surface to increase the yield of distillable oil.

Has the use of talc an effect on yield and extra virgin olive oil quality?

PubMed

Caponio, Francesco; Squeo, Giacomo; Difonzo, Graziana; Pasqualone, Antonella; Summo, Carmine; Paradiso, Vito Michele

2016-08-01

The maximization of both extraction yield and extra virgin olive oil quality during olive processing are the main objectives of the olive oil industry. As regards extraction yield, it can be improved by both acting on time/temperature of malaxation and using physical coadjuvants. It is well known that, generally, increasing temperature of malaxation gives an increase in oil extraction yield due to a reduction in oily phase viscosity; however, high malaxation temperature can compromise the nutritional and health values of extra virgin olive oil, leading to undesirable effects such as accelerated oxidative process and loss of volatile compounds responsible for oil flavor and fragrance. The addition of physical coadjuvants in olive oil processing during the malaxation phase, not excluded by EC regulations owing to its exclusively physical action, is well known to promote the breakdown of oil/water emulsions and consequently make oil extraction easier, thus increasing the yield. Among physical coadjuvants, micronized natural talc is used for olive oil processing above all for Spanish and Italian olive cultivars. The quality of extra virgin olive oil depends on numerous variables such as olive cultivar, ripeness degree and quality, machines utilized for processing, oil storage conditions, etc. However, the coadjuvants utilized in olive processing can also influence virgin olive oil characteristics. The literature highlights an increase in oil yield by micronized natural talc addition during olive processing, whereas no clear trend was observed as regards the chemical, nutritional and sensory characteristics of extra virgin olive oil. Although an increase in oil stability was reported, no effect of talc was found on the evolution of virgin olive oil quality indices during storage. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

The OCLC-SERHOLD connection: an evolution in health sciences union listing.

PubMed Central

Battistella, M S

1991-01-01

The OCLC Union List Subsystem (OCLC ULS) provides a standard, high quality, and widely used means of managing union list data. Over the last several years, OCLC ULS tape products have been used by thirteen health sciences libraries or groups to update SERHOLD. These thirteen libraries or groups were surveyed to examine practices in using OCLC to update SERHOLD. The National Library of Medicine's (NLM) processing of OCLC tape products was assessed to determine how OCLC data are handled by SERHOLD. Most important are the assignment of OCLC holdings symbols, OCLC record selection criteria, tape pull cycles, and the processing of exception reports produced by NLM as a result of tape loads. PMID:1958909

The OCLC-SERHOLD connection: an evolution in health sciences union listing.

PubMed

Battistella, M S

1991-10-01

The OCLC Union List Subsystem (OCLC ULS) provides a standard, high quality, and widely used means of managing union list data. Over the last several years, OCLC ULS tape products have been used by thirteen health sciences libraries or groups to update SERHOLD. These thirteen libraries or groups were surveyed to examine practices in using OCLC to update SERHOLD. The National Library of Medicine's (NLM) processing of OCLC tape products was assessed to determine how OCLC data are handled by SERHOLD. Most important are the assignment of OCLC holdings symbols, OCLC record selection criteria, tape pull cycles, and the processing of exception reports produced by NLM as a result of tape loads.

Study of optimal extraction conditions for achieving high yield and antioxidant activity of tomato seed oil.

PubMed

Shao, Dongyan; Atungulu, Griffiths G; Pan, Zhongli; Yue, Tianli; Zhang, Ang; Li, Xuan

2012-08-01

Value of tomato seed has not been fully recognized. The objectives of this research were to establish suitable processing conditions for extracting oil from tomato seed by using solvent, determine the impact of processing conditions on yield and antioxidant activity of extracted oil, and elucidate kinetics of the oil extraction process. Four processing parameters, including time, temperature, solvent-to-solid ratio and particle size were studied. A second order model was established to describe the oil extraction process. Based on the results, increasing temperature, solvent-to-solid ratio, and extraction time increased oil yield. In contrast, larger particle size reduced the oil yield. The recommended oil extraction conditions were 8 min of extraction time at temperature of 25 °C, solvent-to-solids ratio of 5/1 (v/w) and particle size of 0.38 mm, which gave oil yield of 20.32% with recovery rate of 78.56%. The DPPH scavenging activity of extracted oil was not significantly affected by the extraction parameters. The inhibitory concentration (IC(50) ) of tomato seed oil was 8.67 mg/mL which was notably low compared to most vegetable oils. A 2nd order model successfully described the kinetics of tomato oil extraction process and parameters of extraction kinetics including initial extraction rate (h), equilibrium concentration of oil (C(s) ), and the extraction rate constant (k) could be precisely predicted with R(2) of at least 0.957. The study revealed that tomato seed which is typically treated as a low value byproduct of tomato processing has great potential in producing oil with high antioxidant capability. The impact of processing conditions including time, temperature, solvent-to-solid ratio and particle size on yield, and antioxidant activity of extracted tomato seed oil are reported. Optimal conditions and models which describe the extraction process are recommended. The information is vital for determining the extraction processing conditions for industrial production of high quality tomato seed oil. Journal of Food Science © 2012 Institute of Food Technologists® No claim to original US government works.

Olive oil supplemented with Coenzyme Q(10): effect on plasma and lipoprotein oxidative status.

PubMed

Brugè, Francesca; Bacchetti, Tiziana; Principi, Federica; Scarpa, Emanuele-Salvatore; Littarru, Gian Paolo; Tiano, Luca

2012-01-01

Olive oil consumption is associated with protective cardiovascular properties, including some beneficial modifications in lipoprotein profile and composition. Coenzyme Q(10) (CoQ(10)) exerts a protective effect on plasma lipoproteins. Aim of the study was to investigate whether extra virgin (EV) olive oil enriched with CoQ(10) affects CoQ(10) levels and oxidative status in plasma and in isolated lipoproteins. Twelve subjects were administered 20 mL olive oil per day for 2 weeks, followed by 2 weeks of olive oil enriched with 20 mg and 2 more weeks with 40 mg of CoQ(10). Plasma and isolated lipoproteins were collected in each phase of the study and subsequently analyzed to assess lipid profile, CoQ10 levels, ORAC assay, resistance of lipoproteins to peroxidation and paroxonase 1 activity. Plasma CoQ(10) levels significantly increased with the 20 mg (+73%) and 40 mg dose (+170%), while the percentage of oxidized CoQ(10) decreased. A significant inverse correlation was found in plasma between percentage of oxidized CoQ(10) and total antioxidant capacity. A lower susceptibility of LDL to peroxidation was also found. Finally, a positive correlation was observed between concentration of CoQ(10) in HDL and paraoxonase-1 activity. EV olive oil enriched with both doses of CoQ(10) significantly affects its bioavailability and plasma redox status. These changes are associated with a decreased susceptibility of plasma lipoproteins to peroxidation associated with a chain-breaking antioxidant activity of the formulation. Copyright © 2012 International Union of Biochemistry and Molecular Biology, Inc.

Development of a rotary union for Gifford-McMahon cryocoolers utilized in a 10 MW offshore superconducting wind turbine

NASA Astrophysics Data System (ADS)

Sun, Jiuce; Sanz, Santiago; León, Andrés; Fraser, Jim; Neumann, Holger

2017-12-01

Superconducting generators (SCG) show the potential to reduce the head mass of large offshore wind turbines. By evaluating the availability and required cooling capacity in the temperatures range around 20 K, a Gifford-McMahon (GM) cryocooler among all the candidates was selected. The cold head of GM cryocooler is supposed to rotate together with the rotating superconducting coil. However, the scroll compressor of the GM cryocooler must stay stationary due to lubricating oil. As a consequence, a rotary helium union (RHU) utilizing Ferrofluidic® sealing technology was successfully developed to transfer helium gas between the rotating cold head and stationary helium compressor at ambient temperatures. It contains a high-pressure and low-pressure helium path with multiple ports, respectively. Besides the helium line, slip rings with optical fiber channels are also integrated into this RHU to transfer current and measurement signals. With promising preliminary test results, the RHU will be installed in a demonstrator of SCG and further performance investigation will be performed.

Polycyclic aromatic hydrocarbons (PAHs) content of edible vegetable oils in Iran: A risk assessment study.

PubMed

Yousefi, Mojtaba; Shemshadi, Ghazal; Khorshidian, Nasim; Ghasemzadeh-Mohammadi, Vahid; Fakhri, Yadolah; Hosseini, Hedayat; Mousavi Khaneghah, Amin

2018-05-29

Totally forty samples (23 brands) of different types of edible oils including frying oil (n = 14), blended oil (n = 13), sunflower oil (n = 6), corn oil (n = 5) and canola oil (n = 2) from Iran's market were analyzed for PAHs content by a High-performance liquid chromatography coupled with fluorescence detector. Also, the Health risk assessment in the adults and children consumers were estimated by the calculating margin of exposure (MOE) and the incremental lifetime cancer risk (ILCR) in the Monte Carlo Simulation (MCS) method. Approximately all of the samples contained different amounts of PAHs, while concentrations of BaP, PAH 4, PAH 8 and PAH 13 were reported as 0.90-11.33, 3.51-84.03, 7.41-117.12 and 129.28-19.54 μg/kg, respectively. Light polycyclic aromatic hydrocarbons corresponded to 65% of total PAHs while the remaining 35% belonged to heavy polycyclic aromatic hydrocarbons. Based on BaP content, 12 samples were above the standard limits (2 μg/kg) which set by the Standard Organization of Iran and the European Union, whereas 15 samples exceeded maximum limit 10 μg/kg set for PAH 4 established by EU. Percentile 95% of MOE in the adults due to ingestion of sunflower, corn, frying and blended oils were determined as 4.10E+5; 4.05E+5; , 2.17E+5, 2.33E+5, respectively and in the children due to ingestion of sunflower oil, corn oil, frying oil and blended oil were calculated as 5.38E+4, 4.49E+4, 2.86E+4, 3.37E+4. Regarding the percentile of 95% ILCR in the adults due to ingestion of sunflower oil, corn oil, frying oil and blended oil were reported as 4.5E-6, 4.17E-6l, 5.20E-6, 4.93E-6 and also this value in the children in the same rank order of products can be summarized as 3.43E-5, 3.94 E-5, 3.17E-5, 3.76E-5. The rank order of edible oils investigated based on MOE was sunflower oil > corn oil > blended oil > frying oil; and based on ILCR, frying oil > blended oil > sunflower oil > corn oil. The health risk assessment according to MCS method indicated that adults and children are not at considerable health risk; MOE ≥ 1E+4 and ILCR < 1E-4). Copyright © 2018. Published by Elsevier Ltd.

Graft union formation in tomato plants: peroxidase and catalase involvement.

PubMed

Fernandez-Garcia, Nieves; Carvajal, Micaela; Olmos, Enrique

2004-01-01

The use of grafted plants in vegetable crop production is now being expanded greatly. However, few data are available on the formation of graft unions in vegetables. In this work, the structural development of the graft union formation in tomato plants is studied, together with the possible relationship with activities of peroxidases and catalases. Tomato (Lycopersicon esculentum Mill.) seedlings of cultivar Fanny were grafted on the rootstock of cultivar AR-9704 using the 'tongue approach grafting' method, and were grown in a crop chamber. A study of the structural development of the graft union and the involvement of peroxidases and catalases in the process of graft formation was carried out during the first stages of the graft union (4, 8 and 15 d after grafting). Observation of the structure of the graft union showed formation of xylem and phloem vessels through the graft union 8 d after grafting. In addition, root hydraulic conductance, L0, indicate that the graft union is fully functional 8 d after grafting, which coincided with an increase of peroxidase and catalase activities. These results suggest that increased peroxidase and catalase activities might be implicated in graft development in tomato plants.

Soviet Muslim Policy: Domestic and Foreign Policy Linkages.

DTIC Science & Technology

1980-04-30

centered in Khuzhistan at the head of the Persian Gulf and Iran’s oil production area. Strikes by the Arab workers were one of the critical elements...286; John Soper, "Is the Soviet Union Interested in Playing the Uigur Card?" Radio Liberty Research, No. 69/79, March 1, 1979; David R. Staats , "The...Uighur Press and the Sino-Soviet Conflict, ibid., No. 147/77, June 15, 1977. 43. David R. Staats , "Sinkiang and ’The China Card,"’ ibid., No. 171/79

How Will Vietnam’s Economic Relationship and Dependency on China Affect Its Response to China’s Increasing Threat to Its Sovereignty?

DTIC Science & Technology

2015-06-01

Soviet Union collapsed.26 Carl A. Thayer, a Vietnam expert with the University of New South Wales in Australia, also argues that the geo-strategic...is Vietnam’s number one export market. Carl A. Thayer uses similar arguments to Le’s hedging strategy. Thayer identifies three strategies that...to threaten or punish it for the way Hanoi was responding to the oil rig incident. According to Jason Morris- Jung , a Vietnam expert at the

Health hazard evaluation report HETA 83-248-1515, Arco Philadelphia refinery, Philadelphia, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, F.A.; Parrish, G.

1984-10-01

A bulk sample of fractionator residue was analyzed for polynuclear aromatic (PNA) compounds at the catalytic cracking unit of ARCO Philadelphia Refinery (SIC-2911), Philadelphia, Pennsylvania in May, 1983. The study was requested by the Atlantic Independent Union to determine if skin rashes and skin irritation occurring among refinery workers were caused by PNA in the fractionators. The authors conclude that a health hazard from exposure to chemicals at the cracking unit may exist. No specific chemical agent can be identified. Dust from the catalyst and oily residues that could contaminate workers shoes and clothing may have contributed to some ofmore » the dermatitis cases. Recommendations include laundering workers coveralls by dry cleaning to insure the removal of oily residues, providing workers with oil resistant or oil proof work boots, and repairing the ventilator in the sample preparation room adjacent to the block house.« less

Recovery of biomolecules from food wastes--a review.

PubMed

Baiano, Antonietta

2014-09-17

Food wastes are produced by a variety of sources, ranging from agricultural operations to household consumption. About 38% occurs during food processing. At present, the European Union legislation encourages the exploitation of co-products. This valorisation can be achieved through the extraction of high-value components such as proteins, polysaccharides, fibres, flavour compounds, and phytochemicals, which can be re-used as nutritionally and pharmacologically functional ingredients. Extraction can proceed according to solid-liquid extraction, Soxhlet extraction, pressurized fluid extraction, supercritical fluid extraction, ultrasound-assisted extraction, microwave-assisted extraction, pulsed electric field extraction, and enzyme-assisted extraction. Nevertheless, these techniques cannot be used indiscriminately and their choice depends on the type of biomolecules and matrix, the scale processing (laboratory or industrial), the ratio between production costs and economic values of the compounds to be extracted. The vegetable wastes include trimmings, peelings, stems, seeds, shells, bran, residues remaining after extraction of oil, starch, sugar, and juice. The animal-derived wastes include wastes from bred animals, wastes from seafood, wastes from dairy processing. The recovered biomolecules and by-products can be used to produce functional foods or as adjuvants in food processing or in medicinal and pharmaceutical preparations. This work is an overview of the type and amounts of food wastes; food waste legislation; conventional and novel techniques suitable for extracting biomolecules; food, medicinal and pharmaceutical uses of the recovered biomolecules and by-products, and future trends in these areas.

Polychlorinated dibenzo-p-dioxins, dibenzofurans and dioxin-like PCBs in commercialized food products from Colombia.

PubMed

Pemberthy, D; Quintero, A; Martrat, M G; Parera, J; Ábalos, M; Abad, E; Villa, A L

2016-10-15

Polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dl-PCBs) are commonly known as dioxins and are the most toxic members of persistent organic pollutants (POPs) because present a variety of health effects especially as promoting agent of growing and transformation of cancer cells. They are bio-accumulate in humans primarily via the diet, specifically by ingestion of foods that have high lipid content which are generally associated with foods of animal origin such as oils and fats and with fishery and dairy products. In Colombia the Ministry of Health and Social Protection which is the entity responsible for surveillance food conditions, has established maximum levels for dioxins and dl-PCBs in oils from animal and vegetable origins. Oils of vegetable and animal origin represent an appreciable intake in the country thus the presence of dioxins and dl-PCBs in these materials is a matter of concern because they can bioaccumulate in fat. In this contribution the levels of PCDD/Fs and dl-PCBs in olive, soybean, fish oil, butter and shrimp consumed in Colombia were determined using HRGC-HRMS and were compared with the maximum levels permitted in oil samples according to both the Colombian and European regulations. WHO-TEQ concentrations for PCDD/Fs and dioxin like PCBs ranged from 0.24 to 1.710pgWHO-TEQ PCDD/Fg(-1) of fat and from 0.050 to 3.000pgWHO-TEQ PCBg(-1) of fat, respectively. As expected, fish oils and shrimp present the highest WHO-TEQ PCDD/Fs and dl-PCBs values followed by butter and soybean oil sample, while the olive oil shows the lowest levels. In general, the vegetable oils show levels below the limits established by both the Colombian and European regulations. The levels from soybean oil found in this study were slightly higher than the threshold established both by the Commission Regulation European Union (EU) and the Colombian legislation, while fish oils showed concentrations above the European regulations. Furthermore, shrimp exhibited values below the maximum concentration levels established by the EU and Colombian regulation. Copyright © 2016. Published by Elsevier B.V.

Valorization of solid waste products from olive oil industry as potential adsorbents for water pollution control--a review.

PubMed

Bhatnagar, Amit; Kaczala, Fabio; Hogland, William; Marques, Marcia; Paraskeva, Christakis A; Papadakis, Vagelis G; Sillanpää, Mika

2014-01-01

The global olive oil production for 2010 is estimated to be 2,881,500 metric tons. The European Union countries produce 78.5% of the total olive oil, which stands for an average production of 2,136,000 tons. The worldwide consumption of olive oil increased of 78% between 1990 and 2010. The increase in olive oil production implies a proportional increase in olive mill wastes. As a consequence of such increasing trend, olive mills are facing severe environmental problems due to lack of feasible and/or cost-effective solutions to olive-mill waste management. Therefore, immediate attention is required to find a proper way of management to deal with olive mill waste materials in order to minimize environmental pollution and associated health risks. One of the interesting uses of solid wastes generated from olive mills is to convert them as inexpensive adsorbents for water pollution control. In this review paper, an extensive list of adsorbents (prepared by utilizing different types of olive mill solid waste materials) from vast literature has been compiled, and their adsorption capacities for various aquatic pollutants removal are presented. Different physicochemical methods that have been used to convert olive mill solid wastes into efficient adsorbents have also been discussed. Characterization of olive-based adsorbents and adsorption mechanisms of various aquatic pollutants on these developed olive-based adsorbents have also been discussed in detail. Conclusions have been drawn from the literature reviewed, and suggestions for future research are proposed.

Oil content Monitor/Control system and method

NASA Astrophysics Data System (ADS)

Schmitt, R. F.; Gavin, J. A.; Kempel, F. D.; Waltrick, C. N.

1985-07-01

This patent application discloses an oil content monitor/control unit system which is configured to automatically monitor and control processed effluent from an associated oil/water separator so that if the processed effluent exceeds predetermined in-port or at-sea oil concentration limits, it is either recirculated to an associated oil/water separator via a ship's bilge for additional processing, or diverted to a holding tank for storage. On the other hand, if the oil concentration of the processed effluent is less than determined in-port or at-sea limits, it is discharged overboard.

A multi-stage oil-water-separating process design for the sea oil spill recovery robot

NASA Astrophysics Data System (ADS)

Zhang, Min-ge; Wu, Jian-guo; Lin, Xinhua; Wang, Xiao-ming

2018-03-01

Oil spill have the most common pollution to the marine ecological environment. In the late stage of physical method recovery, because of the thin oil and the strong sea breeze, the recovery vessels has low efficiency and high energy consumption. This paper develops a multi-stage oil-water-separating process carried by the sea oil spill recovery robot in severe conditions. This design consists of three separation process, among which both the first and third process adopt corrugated sheets horizontal oil-water separator, while the second is hydraulic rotary breaker. This design also equiptment with rectifier and cyclone separator and other important components. This process has high flexibility and high recovery efficiency. The implement effect is significant.

Natural Zeolite Sample and Investigation Its Use in Oil Bleaching Sector

NASA Astrophysics Data System (ADS)

Bilgin, Oyku

2017-12-01

In the sector of oil bleaching, the stored raw oil is subjected to physical and chemical methods such as degumming, neutralization, bleaching, deodorization and winterization. In the process of oil bleaching, the selection of correct bleaching earth in accordance with oil characteristics matters so much. Bleaching earth is an inorganic product used in removing impurities being available within the structures of vegetable, animal oil (sunflower, soya, corn, palm, tallow, rapeseed, fish oils…etc.) and fatty acids, mineral oils (glycerine, paraffin, mineral motor oils. etc.) with the adsorption process. The factors such as low cost of oil bleaching earth, low ratio of oil retaining, high bleaching capacity in spite of using them in small amounts, filter’s delayed blocking by the earth and non-increase of the free acidity of the oil should be taken into consideration. Bleaching earths are processed with some acids in order to widen their surface areas. During this process, a certain amount of acid is left within oil bleaching earths even if it is very little. These acids also increase oil’s acidity by oxidizing oil in the course of bleaching process. In this study, zeolite sample taken from Manisa -Demirci region was used. Following the processes of crushing and sieving, zeolite sample was subjected to chemical analyses according to their grain thickness, microscopic examination, the analyses of XRD and cation exchange capacity and their ore characteristics were determined. Afterwards, it was searched whether zeolite sample has oil bleaching ability or not or whether it can be used as oil bleaching earth or not.

Topological color codes on Union Jack lattices: a stable implementation of the whole Clifford group

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katzgraber, Helmut G.; Theoretische Physik, ETH Zurich, CH-8093 Zurich; Bombin, H.

We study the error threshold of topological color codes on Union Jack lattices that allow for the full implementation of the whole Clifford group of quantum gates. After mapping the error-correction process onto a statistical mechanical random three-body Ising model on a Union Jack lattice, we compute its phase diagram in the temperature-disorder plane using Monte Carlo simulations. Surprisingly, topological color codes on Union Jack lattices have a similar error stability to color codes on triangular lattices, as well as to the Kitaev toric code. The enhanced computational capabilities of the topological color codes on Union Jack lattices with respectmore » to triangular lattices and the toric code combined with the inherent robustness of this implementation show good prospects for future stable quantum computer implementations.« less

Enhancement of Hydrodynamic Processes in Oil Pipelines Considering Rheologically Complex High-Viscosity Oils

NASA Astrophysics Data System (ADS)

Konakhina, I. A.; Khusnutdinova, E. M.; Khamidullina, G. R.; Khamidullina, A. F.

2016-06-01

This paper describes a mathematical model of flow-related hydrodynamic processes for rheologically complex high-viscosity bitumen oil and oil-water suspensions and presents methods to improve the design and performance of oil pipelines.

The development of recent high-power ultrasonic transducers for Near-well ultrasonic processing technology.

PubMed

Wang, Zhenjun; Xu, Yuanming

2017-07-01

With the reduction of crude oil throughout the world, enhance oil recovery technology has become a major oil research topics, which can greatly increase the recovery ratio of the crude oil before the dawning of renewable energy era. Near-well ultrasonic processing technology, as one new method, has attracted more attention for Enhanced Oil Recovery due to its low cost, good applicability and no environmental pollution in recent rears. There are two important relevant aspects about Near-well ultrasonic processing technology: (a) how to enhance the oil flow through the rocks into the pumping pool and (b) how to reduce the oil viscosity so that it can be easier to pump. Therefore, how to design a high-power ultrasonic equipment with excellent performance is crucial for Near-well ultrasonic processing technology. In this paper, recent new high-power ultrasonic transducers for Near-well ultrasonic processing technology are summarized. Each field application of them are also given. The purpose of this paper is to provide reference for the further development of Near-well ultrasonic processing technology. With the reduction of crude oil throughout the world, enhance oil recovery technology has become a major oil research topics, which can greatly increase the recovery ratio of the crude oil before the dawning of renewable energy era. Near-well ultrasonic processing technology, as one new method, has attracted more attention for Enhanced Oil Recovery due to its low cost, good applicability and no environmental pollution in recent rears. There are two important relevant aspects about Near-well ultrasonic processing technology: (a) how to enhance the oil flow through the rocks into the pumping pool and (b) how to reduce the oil viscosity so that it can be easier to pump. Therefore, how to design a high-power ultrasonic equipment with excellent performance is crucial for Near-well ultrasonic processing technology. In this paper, recent new high-power ultrasonic transducers for Near-well ultrasonic processing technology are summarized. Each field application of them are also given. The purpose of this paper is to provide reference for the further development of Near-well ultrasonic processing technology. Copyright © 2017 Elsevier B.V. All rights reserved.

Multiclass pesticide determination in olives and their processing factors in olive oil: comparison of different olive oil extraction systems.

PubMed

Amvrazi, Elpiniki G; Albanis, Triantafyllos A

2008-07-23

The processing factors (pesticide concentration found in olive oil/pesticide concentration found in olives) of azinphos methyl, chlorpyrifos, lambda-cyhalothrin, deltamethrin, diazinon, dimethoate, endosulfan, and fenthion were determined in olive oil production process in various laboratory-scale olive oil extractions based on three- or two-phase centrifugation systems in comparison with samples collected during olive oil extractions in conventional olive mills located at different olive oil production areas in Greece. Pesticide analyses were performed using a multiresidue method developed in our laboratory for the determination of different insecticides and herbicides in olive oil by solid-phase extraction techniques coupled to gas chromatography detection (electron capture detection and nitrogen phosphorus detection), optimized, and validated for olive fruits sample preparation. Processing factors were found to vary among the different pesticides studied. Water addition in the oil extraction procedure (as in a three-phase centrifugation system) was found to decrease the processing factors of dimethoate, alpha-endosulfan, diazinon, and chlorpyrifos, whereas those of fenthion, azinphos methyl, beta-endosulfan, lambda-cyhalothrin, and deltamethrin residues were not affected. The water content of olives processed was found to proportionally affect pesticide processing factors. Fenthion sulfoxide and endosulfan sulfate were the major metabolites of fenthion and endosulfan, respectively, that were detected in laboratory-produced olive oils, but only the concentration of fenthion sulfoxide was found to increase with the increase of water addition in the olive oil extraction process.

Other factors to consider in the formation of chloropropandiol fatty esters in oil processes.

PubMed

Ramli, Muhamad Roddy; Siew, Wai Lin; Ibrahim, Nuzul Amri; Kuntom, Ainie; Abd Razak, Raznim Arni

2015-01-01

This paper examines the processing steps of extracting palm oil from fresh fruit bunches in a way that may impact on the formation of chloropropandiol fatty esters (3-MCPD esters), particularly during refining. Diacylglycerols (DAGs) do not appear to be a critical factor when crude palm oils are extracted from various qualities of fruit bunches. Highly hydrolysed oils, in spite of the high free fatty acid (FFA) contents, did not show exceptionally high DAGs, and the oils did not display a higher formation of 3-MCPD esters upon heat treatment. However, acidity measured in terms of pH appears to have a strong impact on 3-MCPD ester formation in the crude oil when heated at high temperatures. The differences in the extraction process of crude palm oil from current commercial processes and that from a modified experimental process showed clearly the effect of acidity of the oil on the formation of 3-MCPD esters. This paper concludes that the washing or dilution step in palm oil mills removes the acidity of the vegetative materials and that a well-optimised dilution/washing step in the extraction process will play an important role in reducing formation of 3-MCPD esters in crude palm oil upon further heat processing.

[Efficiency evaluation of capsaicinoids to discriminate bio-waste oils from edible vegetable oils].

PubMed

Mao, Lisha; Liu, Honghe; Kang, Li; Jiang, Jie; Liao, Shicheng; Liu, Guihua; Deng, Pingjian

2014-07-01

To evaluate the efficiency of capsaicinoids to discriminate bio-waste oil from edible vegetable oil. 14 raw vegetable oils, 24 fried waste oils, 34 kitchen-waste oils, 32 edible non-peanut vegetable oil, 32 edible peanuts oil, 16 edible oil add flavorand and 11 refined bio-waste oils were prepared and examined for capsaicinoids including capsaicin, dihydrocapsaicin and nonylic acid vanillylamide. The detection results of the above samples were statistically tested based on sample category to assessment identify the effectiveness of the bio-waste oils with capsaicinoids. As a indicator, capsaincin was possessed of high detection sensitivity and has the highest efficiency to discern kitchen-waste oils and refined bio-waste oils samples from edible non-peanut vegetable oil correctly. The accuracy rate of identification were 100% and 90.1% respectively. There is the background in peanut oil. CONCLUSION Capsaicin added in cooking process can be retained in the refining process and hardly be removed in the refining process. In the case of fully eliminating the background interference, capsaicinoids can effectively identify bio-waste oils and edible vegetable oil in combination.

Interlibrary Lending with Computerized Union Catalogues.

ERIC Educational Resources Information Center

Lehmann, Klaus-Dieter

Interlibrary loans in the Federal Republic of Germany are facilitated by applying techniques of data processing and computer output microfilm (COM) to the union catalogs of the national library system. The German library system consists of two national libraries, four central specialized libraries of technology, medicine, agriculture, and…

Unionizing in Chicago: Big Gains for Part-Timers.

ERIC Educational Resources Information Center

Laiacona, Joseph

2000-01-01

Recounts how the part-time faculty at Chicago's Columbia College (Illinois) dramatically improved salaries and gained a strong voice in college decision making through unionization. Emphasis is on the negotiation process which worked to obtain the group's goals without undermining the "rather friendly college environment." (DB)

Pore-scale simulation of wettability and interfacial tension effects on flooding process for enhanced oil recovery.

PubMed

Zhao, Jin; Wen, Dongsheng

2017-08-27

For enhanced oil recovery (EOR) applications, the oil/water flow characteristics during the flooding process was numerically investigated with the volume-of-fluid method at the pore scale. A two-dimensional pore throat-body connecting structure was established, and four scenarios were simulated in this paper. For oil-saturated pores, the wettability effect on the flooding process was studied; for oil-unsaturated pores, three effects were modelled to investigate the oil/water phase flow behaviors, namely the wettability effect, the interfacial tension (IFT) effect, and the combined wettability/IFT effect. The results show that oil saturated pores with the water-wet state can lead to 25-40% more oil recovery than with the oil-wet state, and the remaining oil mainly stays in the near wall region of the pore bodies for oil-wet saturated pores. For oil-unsaturated pores, the wettability effects on the flooding process can help oil to detach from the pore walls. By decreasing the oil/water interfacial tension and altering the wettability from oil-wet to water-wet state, the remaining oil recovery rate can be enhanced successfully. The wettability-IFT combined effect shows better EOR potential compared with decreasing the interfacial tension alone under the oil-wet condition. The simulation results in this work are consistent with previous experimental and molecular dynamics simulation conclusions. The combination effect of the IFT reducation and wettability alteration can become an important recovery mechanism in future studies for nanoparticles, surfactant, and nanoparticle-surfactant hybrid flooding process.

Pore-scale simulation of wettability and interfacial tension effects on flooding process for enhanced oil recovery

PubMed Central

Zhao, Jin

2017-01-01

For enhanced oil recovery (EOR) applications, the oil/water flow characteristics during the flooding process was numerically investigated with the volume-of-fluid method at the pore scale. A two-dimensional pore throat-body connecting structure was established, and four scenarios were simulated in this paper. For oil-saturated pores, the wettability effect on the flooding process was studied; for oil-unsaturated pores, three effects were modelled to investigate the oil/water phase flow behaviors, namely the wettability effect, the interfacial tension (IFT) effect, and the combined wettability/IFT effect. The results show that oil saturated pores with the water-wet state can lead to 25–40% more oil recovery than with the oil-wet state, and the remaining oil mainly stays in the near wall region of the pore bodies for oil-wet saturated pores. For oil-unsaturated pores, the wettability effects on the flooding process can help oil to detach from the pore walls. By decreasing the oil/water interfacial tension and altering the wettability from oil-wet to water-wet state, the remaining oil recovery rate can be enhanced successfully. The wettability-IFT combined effect shows better EOR potential compared with decreasing the interfacial tension alone under the oil-wet condition. The simulation results in this work are consistent with previous experimental and molecular dynamics simulation conclusions. The combination effect of the IFT reducation and wettability alteration can become an important recovery mechanism in future studies for nanoparticles, surfactant, and nanoparticle–surfactant hybrid flooding process. PMID:29308190

Current knowledge and potential applications of cavitation technologies for the petroleum industry.

PubMed

Avvaru, Balasubrahmanyam; Venkateswaran, Natarajan; Uppara, Parasuveera; Iyengar, Suresh B; Katti, Sanjeev S

2018-04-01

Technologies based on cavitation, produced by either ultrasound or hydrodynamic means, are part of growing literature for individual refinery unit processes. In this review, we have explained the mechanism through which these cavitation technologies intensify individual unit processes such as enhanced oil recovery, demulsification of water in oil emulsions during desalting stage, crude oil viscosity reduction, oxidative desulphurisation/demetallization, and crude oil upgrading. Apart from these refinery processes, applications of this technology are also mentioned for other potential crude oil sources such as oil shale and oil sand extraction. The relative advantages and current situation of each application/process at commercial scale is explained. Copyright © 2017 Elsevier B.V. All rights reserved.

Process for removing polychlorinated and polybrominated biphenyls from oils

DOEpatents

Orlett, M.J.

The invention is a relatively simple and inexpensive process for detoxifying oils contaminated with PCBs and/or PBBs. The process is especially suitable for processing lubricating oils containing such contaminants. In one aspect of the invention, the contaminated lubricating oil is contacted with a particulate reagent comprising adsorbent particles carrying a dispersion of metallic sodium. The solid sodium reagent converts the PCB and/or PBB contaminants to environmentally acceptable products and also converts various sodium-reactive additives normally present in lubricating oil to reaction products. The adsorbent reagent retains most of the products and is easily separated from the detoxified oil. The detoxified oil may be fortified with various additives functionally equivalent to those removed during detoxification.

Life cycle greenhouse gas emissions, consumptive water use and levelized costs of unconventional oil in North America

NASA Astrophysics Data System (ADS)

Mangmeechai, Aweewan

Conventional petroleum production in many countries that supply U.S. crude oil as well as domestic production has declined in recent years. Along with instability in the world oil market, this has stimulated the discussion of developing unconventional oil production, e.g., oil sands and oil shale. Expanding the U.S. energy mix to include oil sands and oil shale may be an important component in diversifying and securing the U.S. energy supply. At the same time, life cycle GHG emissions of these energy sources and consumptive water use are a concern. In this study, consumptive water use includes not only fresh water use but entire consumptive use including brackish water and seawater. The goal of this study is to determine the life cycle greenhouse gas (GHG) emissions and consumptive water use of synthetic crude oil (SCO) derived from Canadian oil sands and U.S. oil shale to be compared with U.S. domestic crude oil, U.S. imported crude oil, and coal-to-liquid (CTL). Levelized costs of SCO derived from Canadian oil sands and U.S. oil shale were also estimated. The results of this study suggest that CTL with no carbon capture and sequestration (CCS) and current electricity grid mix is the worst while crude oil imported from United Kingdom is the best in GHG emissions. The life cycle GHG emissions of oil shale surface mining, oil shale in-situ process, oil sands surface mining, and oil sands in-situ process are 43% to 62%, 13% to 32%, 5% to 22%, and 11% to 13% higher than those of U.S. domestic crude oil. Oil shale in-situ process has the largest consumptive water use among alternative fuels, evaluated due to consumptive water use in electricity generation. Life cycle consumptive water use of oil sands in-situ process is the lowest. Specifically, fresh water consumption in the production processes is the most concern given its scarcity. However, disaggregated data on fresh water consumption in the total water consumption of each fuel production process is not available. Given current information, it is inconclusive whether unconventional oil would require more or less consumptive fresh water use than U.S. domestic crude oil production. It depends on the water conservative strategy applied in each process. Increasing import of SCO derived from Canadian oil sands and U.S. oil shale would slightly increase life cycle GHG emissions of the U.S. petroleum status quo. The expected additional 2 million bpd of Canadian SCO from oil sands and U.S. oil shale would increase life cycle GHG emissions of the U.S. petroleum status quo on average only 10 and 40 kg CO2 equiv/bbl, or about 7.5 and 29 million tons CO2 equiv/year. However this increase represents less than 1 and 5% of U.S. transportation emissions in 2007. Because U.S. oil shale resources are located in areas experiencing water scarcity, methods to manage the issue were explored. The result also shows that trading water rights between Upper and Lower Colorado River basin and transporting synthetic crude shale oil to refinery elsewhere is the best scenario for life cycle GHG emissions and consumptive water use of U.S. oil shale production. GHG emissions and costs of water supply system contribute only 1-2% of life cycle GHG emissions and 1-6% of total levelized costs. The levelized costs of using SCO from oil shale as feedstock are greater than SCO from oil sands, and CTL. The levelized costs of producing liquid fuel (gasoline and diesel) using SCO derived from Canadian oil sands as feedstock are approximately 0.80-1.00/gal of liquid fuel. The levelized costs of SCO derived from oil shale are 1.6-4.5/gal of liquid fuel (oil shale surface mining process) and 1.6-5.2/gal of liquid fuel (oil shale in-situ process). From an energy security perspective, increasing the use of Canadian oil sands, U.S. oil shale, and CTL may be preferable to increasing Middle East imports. However, oil shale and CTL has the advantage security wise over Canadian oil sands because oil shale and coal are abundant U.S. resources. From a GHG emissions and consumptive water use perspective, CTL requires less consumptive water use than oil shale in-situ process but produces more GHG emissions than oil shale in-situ and surface mining process, unless CTL plant performs CCS and renewable electricity.

Geology of the Cooper Ridge NE Quadrangle, Sweetwater County, Wyoming

USGS Publications Warehouse

Roehler, Henry W.

1979-01-01

The Cooper Ridge NE 7?-minute quadrangle is 18 miles southeast of Rock Springs, Wyo., on the east flank of the Rock Springs uplift. Upper Cretaceous rocks composing the Rock Springs Formation, Ericson Sandstone, Almond Formation, Lewis Shale, Fox Hills Sandstone, and Lance Formation, Paleocene rocks composing the Fort Union Formation, and Eocene rocks composing the Wasatch Formation are exposed and dip 5?-8? southeast. Outcrops are unfaulted and generally homoclinal, but a minor cross-trending fold, the Jackknife Spring anticline, plunges southeastward and interrupts the northeast strike of beds. Older rocks in the subsurface are faulted and folded, especially near the Brady oil and gas field. Coal beds are present in the Almond, Lance, and Fort Union Formations. Coal resources are estimated to be more than 762 million short tons in 16 beds more than 2.5 feet thick, under less than 3,000 ft of overburden. Nearly 166 million tons are under less than 200 ft of overburden and are recoverable by strip mining. Unknown quantities of oil and gas are present in the Cretaceous Rock Springs, Blair, and Dakota Formations, Jurassic sandstone (Entrada Sandstone of drillers), Jurassic(?) and Triassic(?) Nugget Sandstone, Permian Park City Formation, and Pennsylvanian and Permian Weber Sandstone at the Brady field, part of which is in the southeast corner of the quadrangle, and in the Dakota Sandstone at the Prenalta Corp. Bluewater 33-32 well near the northern edge of the quadrangle. Other minerals include uranium in the Almond Formation and titanium in the Rock Springs Formation.

Safe practices, operating rule compliance, and derailment rates improve at Union Pacific Yards with STEEL process : a risk reduction approach to safety.

DOT National Transportation Integrated Search

2008-12-01

After the success of the Federal Railroad Administration (FRA) Human Factors Program demonstration project at Union Pacific (UP) Railroads San Antonio Service Unit (SASU), which focused on managers and road crews with a proactive safety risk reductio...

Collective Bargaining, a New Common Law for College Professors.

ERIC Educational Resources Information Center

Brown, Frank

1980-01-01

In general, collective bargaining for college faculties means that individual faculty members cannot exercise traditional constitutional rights of due process, even if they are not members of the union. Some provisions differ from one state to another. However, both public and private colleges are increasingly voting to unionize. (Author/CTM)

12 CFR 792.15 - How long will it take to process my request?

Code of Federal Regulations, 2012 CFR

2012-01-01

...? 792.15 Section 792.15 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING THE OPERATIONS OF THE NATIONAL CREDIT UNION ADMINISTRATION REQUESTS FOR INFORMATION UNDER THE FREEDOM OF INFORMATION ACT AND PRIVACY ACT, AND BY SUBPOENA; SECURITY PROCEDURES FOR CLASSIFIED INFORMATION The Freedom...

12 CFR 792.15 - How long will it take to process my request?

Code of Federal Regulations, 2011 CFR

2011-01-01

...? 792.15 Section 792.15 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING THE OPERATIONS OF THE NATIONAL CREDIT UNION ADMINISTRATION REQUESTS FOR INFORMATION UNDER THE FREEDOM OF INFORMATION ACT AND PRIVACY ACT, AND BY SUBPOENA; SECURITY PROCEDURES FOR CLASSIFIED INFORMATION The Freedom...

12 CFR 792.15 - How long will it take to process my request?

Code of Federal Regulations, 2014 CFR

2014-01-01

...? 792.15 Section 792.15 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING THE OPERATIONS OF THE NATIONAL CREDIT UNION ADMINISTRATION REQUESTS FOR INFORMATION UNDER THE FREEDOM OF INFORMATION ACT AND PRIVACY ACT, AND BY SUBPOENA; SECURITY PROCEDURES FOR CLASSIFIED INFORMATION The Freedom...

12 CFR 792.15 - How long will it take to process my request?

Code of Federal Regulations, 2010 CFR

2010-01-01

...? 792.15 Section 792.15 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING THE OPERATIONS OF THE NATIONAL CREDIT UNION ADMINISTRATION REQUESTS FOR INFORMATION UNDER THE FREEDOM OF INFORMATION ACT AND PRIVACY ACT, AND BY SUBPOENA; SECURITY PROCEDURES FOR CLASSIFIED INFORMATION The Freedom...

12 CFR 792.15 - How long will it take to process my request?

Code of Federal Regulations, 2013 CFR

2013-01-01

...? 792.15 Section 792.15 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING THE OPERATIONS OF THE NATIONAL CREDIT UNION ADMINISTRATION REQUESTS FOR INFORMATION UNDER THE FREEDOM OF INFORMATION ACT AND PRIVACY ACT, AND BY SUBPOENA; SECURITY PROCEDURES FOR CLASSIFIED INFORMATION The Freedom...

Socialization of the Child in the Soviet Union.

ERIC Educational Resources Information Center

Sandanavicius, Mary

1979-01-01

The socialization process of the child in the Soviet Union is examined in terms of socialistic/communistic political philosophy and the general attitudes of the Soviets toward social sciences, child rearing, and educational practice. The family, school, and youth organizations are also discussed as socializing agents. (Author/KC)

Microbial processes in the Athabasca Oil Sands and their potential applications in microbial enhanced oil recovery.

PubMed

Harner, N K; Richardson, T L; Thompson, K A; Best, R J; Best, A S; Trevors, J T

2011-11-01

The Athabasca Oil Sands are located within the Western Canadian Sedimentary Basin, which covers over 140,200 km(2) of land in Alberta, Canada. The oil sands provide a unique environment for bacteria as a result of the stressors of low water availability and high hydrocarbon concentrations. Understanding the mechanisms bacteria use to tolerate these stresses may aid in our understanding of how hydrocarbon degradation has occurred over geological time, and how these processes and related tolerance mechanisms may be used in biotechnology applications such as microbial enhanced oil recovery (MEOR). The majority of research has focused on microbiology processes in oil reservoirs and oilfields; as such there is a paucity of information specific to oil sands. By studying microbial processes in oil sands there is the potential to use microbes in MEOR applications. This article reviews the microbiology of the Athabasca Oil Sands and the mechanisms bacteria use to tolerate low water and high hydrocarbon availability in oil reservoirs and oilfields, and potential applications in MEOR.

Decision Support Model for Selection Technologies in Processing of Palm Oil Industrial Liquid Waste

NASA Astrophysics Data System (ADS)

Ishak, Aulia; Ali, Amir Yazid bin

2017-12-01

The palm oil industry continues to grow from year to year. Processing of the palm oil industry into crude palm oil (CPO) and palm kernel oil (PKO). The ratio of the amount of oil produced by both products is 30% of the raw material. This means that 70% is palm oil waste. The amount of palm oil waste will increase in line with the development of the palm oil industry. The amount of waste generated by the palm oil industry if it is not handled properly and effectively will contribute significantly to environmental damage. Industrial activities ranging from raw materials to produce products will disrupt the lives of people around the factory. There are many alternative technologies available to process other industries, but problems that often occur are difficult to implement the most appropriate technology. The purpose of this research is to develop a database of waste processing technology, looking for qualitative and quantitative criteria to select technology and develop Decision Support System (DSS) that can help make decisions. The method used to achieve the objective of this research is to develop a questionnaire to identify waste processing technology and develop the questionnaire to find appropriate database technology. Methods of data analysis performed on the system by using Analytic Hierarchy Process (AHP) and to build the model by using the MySQL Software that can be used as a tool in the evaluation and selection of palm oil mill processing technology.

Characteristics of polycyclic aromatic hydrocarbons in food oils in Beijing catering services.

PubMed

Hao, Xuewei; Yin, Yong; Feng, Sijie; Du, Xu; Yu, Jingyi; Yao, Zhiliang

2016-12-01

The concentrations and characteristics of 16 polycyclic aromatic hydrocarbons (PAHs) in 48 oil samples randomly collected from 30 catering services that employ six cooking methods were quantified via high-performance liquid chromatography (HPLC). These 16 PAHs were detected in almost all of the samples. The levels of Σ16PAHs, Σ4PAHs, benzo[a]pyrene (BaP), and total BaP equivalents (ΣBaP eq ) for the six cooking methods exceeded the legal limit. The concentrations of Σ4PAHs were approximately 9.5 to 16.4 times the legal limit proposed by the European Commission (Off J Eur Union 215:4-8, 2011), and the level of BaP exceeded the national standard in China by 4.7- to 10.6-fold, particularly in oil from fried foods. Low molecular weight PAHs (LMW PAHs) were predominant in fried food oil from different catering services and accounted for 94.8 % of these oils, and the ΣBaP eq of the high molecular weight PAHs (HMW PAHs) was 11.5-fold higher than that of the LMW PAHs. The concentrations of Σ16PAHs (3751.9-7585.8 μg/kg), Σ4PAHs (144.6-195.7 μg/kg), BaP (79.7-135.8 μg/kg), and ΣBaP eq (231.0-265.4 μg/kg) were highest in the samples from fast food restaurants/buffets (FB), followed by those from fried food stalls (FS) and then cooking restaurants/cafeterias (RC). The results of this study suggest that the government should strengthen control and supervision of PAH contamination in food and edible oils.

Relationships between volatile compounds and sensory characteristics in virgin olive oil by analytical and chemometric approaches.

PubMed

Procida, Giuseppe; Cichelli, Angelo; Lagazio, Corrado; Conte, Lanfranco S

2016-01-15

The volatile fraction of virgin olive oil is characterised by low molecular weight compounds that vaporise at room temperature. In order to obtain an aroma profile similar to natural olfactory perception, the composition of the volatile compounds was determined by applying dynamic headspace gas chromatography, performed at room temperature, with a cryogenic trap directly connected to a gas chromatograph-mass spectrometer system. Samples were also evaluated according to European Union and International Olive Council official methods for sensory evaluation. In this paper, the composition of the volatile fraction of 25 extra virgin olive oils from different regions of Italy was analysed and some preliminary considerations on relationships between chemical composition of volatile fraction and sensory characteristics are reported. Forty-two compounds were identified by means of the particular analytical technique used. All the analysed samples, classified as extra virgin by the panel test, never present peaks whose magnitude is important enough in defected oils. The study was focused on the evaluation of volatile compounds responsible for the positive impact on olive odour properties ('green-fruity' and 'sweet') and olfactory perception. Chemometric evaluation of data, obtained through headspace analysis and the panel test evaluation, showed a correlation between chemical compounds and sensory properties. On the basis of the results, the positive attributes of virgin olive oil are divided into two separated groups: sweet types or green types. Sixteen volatile compounds with known positive impact on odour properties were extracted and identified. In particular, eight compounds seem correlated with sweet properties whereas the green sensation appears to be correlated with eight other different substances. The content of the compounds at six carbon atoms proves to be very important in defining positive attributes of extra virgin olive oils and sensory evaluation. © 2015 Society of Chemical Industry.

Future for oil and gas in the EEC. I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1974-03-01

This study by UNICE (Union of Industries of the EEC), prepared prior to the October 1973 Mideast conflict, shows remarkable foresight in the light of subsequent events. Of the 3 major industrial units (the U.S., Europe, and Japan), Europe would be in the weakest position in the event of an energy shortage. During the 1973-85 period, the techncal risks threatening the security of Europe's oil supplies are subordinate to the political and economic risks: (1) Certain producing countries may be tempted to use their oil potential as a means of influencing foreign policy by limiting production, (2) international monetary problemsmore » and worldwide inflation may give rise to producer-country reactions which are not confined to the technical field, and (3) the utilization of the vast financial resources of some producer countries may prove a serious problem. UNICE considers it imperative for the EEC, in collaboration with industry and with due regard for the fundamental importance of competition, to arrive at a common energy policy as soon as possible and to take the decisions necessary to ensure the long-term security of energy supplies on satisfactory economic terms. The EEC and the national governments must seek to promote the security of energy supplies in all forms, ensure an adequate profitability level to finance investment, deal more flexibly with environmental problems, adopt a more homogenous attitude, and encourage the development of alternative energy sources. For oil specifically, there are 4 ways of reducing the political and economic risks threatening exploration and production: limiting demand for oil products, increasing energy supplies, facilitating the oil industry's activities, and encouraging action by governments.« less

Bio-oil production from palm fronds by fast pyrolysis process in fluidized bed reactor

NASA Astrophysics Data System (ADS)

Rinaldi, Nino; Simanungkalit, Sabar P.; Kiky Corneliasari, S.

2017-01-01

Fast pyrolysis process of palm fronds has been conducted in the fluidized bed reactor to yield bio-oil product (pyrolysis oil). The process employed sea sand as the heat transfer medium. The objective of this study is to design of the fluidized bed rector, to conduct fast pyrolysis process to product bio-oil from palm fronds, and to characterize the feed and bio-oil product. The fast pyrolysis process was conducted continuously with the feeding rate around 500 g/hr. It was found that the biomass conversion is about 35.5% to yield bio-oil, however this conversion is still minor. It is suggested due to the heating system inside the reactor was not enough to decompose the palm fronds as a feedstock. Moreover, the acids compounds ware mostly observed on the bio-oil product.

Chemical composition, antimicromicrobial activity and insecticidal activity against the lesser mealworm Alphitobius diaperinus (Panzer) (Coleoptera: Tenebrionidae) of Origanum vulgare L. ssp. hirtum (Link) and Artemisia dracunculus L. essential oils.

PubMed

Szczepanik, Maryla; Walczak, Maciej; Zawitowska, Beata; Michalska-Sionkowska, Marta; Szumny, Antoni; Wawrzeńczyk, Czesław; Brzezinska, Maria Swiontek

2018-01-01

Essential oils (EOs) from Artemisia dracunculus L. and Origanum vulgare L. ssp. hirtum were obtained and the qualitative and quantitative chemical composition of the extracts was investigated. The insecticidal activity of EOs against the larval stages of Alphitobius diaperinus (Panzer) was studied. Moreover, the antimicrobial activity of these oils against pathogens transmitted by this pest was also investigated. The obtained results indicate the possibility of using Greek oregano EO with a high content of carvacrol as a feed additive in poultry nutrition. The use of the Greek oregano oil at 1% (w/w) dose showed stronger reduction of body weight gain of stage IV larvae. Their body mass was only 10.92% of the control. Moreover, EOs from O. vulgare strongly inhibited the growth of tested bacterial strains as well as Candida albicans. Greek oregano EO may be a good alternative to antibiotic growth promoters and coccidiostats whose use in feeding farm animals has been prohibited since January 2006 under European Union directives. The introduction of O. vulgare L. ssp. hirtum EO into the premises of farm and poultry houses may help to improve sanitary conditions and control of the lesser mealworm inhabiting these buildings. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Upgrading and Refining of Crude Oils and Petroleum Products by Ionizing Irradiation.

PubMed

Zaikin, Yuriy A; Zaikina, Raissa F

2016-06-01

A general trend in the oil industry is a decrease in the proven reserves of light crude oils so that any increase in future oil exploration is associated with high-viscous sulfuric oils and bitumen. Although the world reserves of heavy oil are much greater than those of sweet light oils, their exploration at present is less than 12 % of the total oil recovery. One of the main constraints is very high expenses for the existing technologies of heavy oil recovery, upgrading, transportation, and refining. Heavy oil processing by conventional methods is difficult and requires high power inputs and capital investments. Effective and economic processing of high viscous oil and oil residues needs not only improvements of the existing methods, such as thermal, catalytic and hydro-cracking, but the development of new technological approaches for upgrading and refining of any type of problem oil feedstock. One of the perspective approaches to this problem is the application of ionizing irradiation for high-viscous oil processing. Radiation methods for upgrading and refining high-viscous crude oils and petroleum products in a wide temperature range, oil desulfurization, radiation technology for refining used oil products, and a perspective method for gasoline radiation isomerization are discussed in this paper. The advantages of radiation technology are simple configuration of radiation facilities, low capital and operational costs, processing at lowered temperatures and nearly atmospheric pressure without the use of any catalysts, high production rates, relatively low energy consumption, and flexibility to the type of oil feedstock.

Physician collective bargaining in a U.S. public hospital.

PubMed

Thompson, Stephen L; Salmon, J Warren

2003-01-01

In a study to investigate the factors that would drive attending physicians employed in a public hospital to seek collective bargaining with their employer, the authors developed an instrument to determine which variables and which hypotheses were predictive of union proneness. The findings reveal that a desire for voice was the number one reason for physicians' wanting to join a union. Union-prone physicians had a lower salary on average, were more dissatisfied with their income, were more likely to feel the effects of work "speed up" (too many patients and too little time), were less likely to have administrative functions (thus a larger patient care role), had a strong sense of entitlement to collective bargaining, believed that unions improve participation in decisions affecting their jobs (reinforcing their desire for voice), and had a sense that a union would improve their treatment by supervisors (reinforcing their desire for due process and equity).

Corrosion Considerations for Thermochemical Biomass Liquefaction Process Systems in Biofuel Production

NASA Astrophysics Data System (ADS)

Brady, M. P.; Keiser, J. R.; Leonard, D. N.; Whitmer, L.; Thomson, J. K.

2014-12-01

Thermochemical liquefaction processing of biomass to produce bio-derived fuels (e.g., gasoline, jet fuel, diesel, home heating oil, etc.) is of great recent interest as a renewable energy source. Approaches under investigation include direct liquefaction, hydrothermal liquefaction, hydropyrolysis, fast pyrolysis, etc., to produce energy dense liquids that can be utilized as produced or further processed to provide products of higher value. An issue with bio-oils is that they tend to contain significant concentrations of organic oxygenates, including acids, which make the bio-oil a potential source of corrosion issues in transport, storage, and use. Efforts devoted to modified/further processing of bio-oils to make them less corrosive are currently being widely pursued. Another issue that must also be addressed in bio-oil liquefaction is potential corrosion issues in the process equipment. Depending on the specific process, bio-oil liquefaction production temperatures are typically in the 300-600°C range, and the process environment can contain aggressive sulfur and halide species from both the biomass used and/or process additives. Detailed knowledge of the corrosion resistance of candidate process equipment alloys in these bio-oil production environments is currently lacking. This paper summarizes recent, ongoing efforts to assess the extent of corrosion of bio-oil process equipment, with the ultimate goal of providing a basis for the selection of the lowest cost alloy grades capable of providing the long-term corrosion resistance needed for future bio-oil production plants.

Low Cost Solar Array Project. Feasibility of the silane process for producing semiconductor-grade silicon. Final report, October 1975-March 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-06-01

The commercial production of low-cost semiconductor-grade silicon is an essential requirement of the JPL/DOE (Department of Energy) Low-Cost Solar Array (LSA) Project. A 1000-metric-ton-per-year commercial facility using the Union Carbide Silane Process will produce molten silicon for an estimated price of $7.56/kg (1975 dollars, private financing), meeting the DOE goal of less than $10/kg. Conclusions and technology status are reported for both contract phases, which had the following objectives: (1) establish the feasibility of Union Carbide's Silane Process for commercial application, and (2) develop an integrated process design for an Experimental Process System Development Unit (EPSDU) and a commercial facility,more » and estimate the corresponding commercial plant economic performance. To assemble the facility design, the following work was performed: (a) collection of Union Carbide's applicable background technology; (b) design, assembly, and operation of a small integrated silane-producing Process Development Unit (PDU); (c) analysis, testing, and comparison of two high-temperature methods for converting pure silane to silicon metal; and (d) determination of chemical reaction equilibria and kinetics, and vapor-liquid equilibria for chlorosilanes.« less

A novel energy-efficient pyrolysis process: self-pyrolysis of oil shale triggered by topochemical heat in a horizontal fixed bed.

PubMed

Sun, You-Hong; Bai, Feng-Tian; Lü, Xiao-Shu; Li, Qiang; Liu, Yu-Min; Guo, Ming-Yi; Guo, Wei; Liu, Bao-Chang

2015-02-06

This paper proposes a novel energy-efficient oil shale pyrolysis process triggered by a topochemical reaction that can be applied in horizontal oil shale formations. The process starts by feeding preheated air to oil shale to initiate a topochemical reaction and the onset of self-pyrolysis. As the temperature in the virgin oil shale increases (to 250-300°C), the hot air can be replaced by ambient-temperature air, allowing heat to be released by internal topochemical reactions to complete the pyrolysis. The propagation of fronts formed in this process, the temperature evolution, and the reaction mechanism of oil shale pyrolysis in porous media are discussed and compared with those in a traditional oxygen-free process. The results show that the self-pyrolysis of oil shale can be achieved with the proposed method without any need for external heat. The results also verify that fractured oil shale may be more suitable for underground retorting. Moreover, the gas and liquid products from this method were characterised, and a highly instrumented experimental device designed specifically for this process is described. This study can serve as a reference for new ideas on oil shale in situ pyrolysis processes.

A Novel Energy-Efficient Pyrolysis Process: Self-pyrolysis of Oil Shale Triggered by Topochemical Heat in a Horizontal Fixed Bed

PubMed Central

Sun, You-Hong; Bai, Feng-Tian; Lü, Xiao-Shu; Li, Qiang; Liu, Yu-Min; Guo, Ming-Yi; Guo, Wei; Liu, Bao-Chang

2015-01-01

This paper proposes a novel energy-efficient oil shale pyrolysis process triggered by a topochemical reaction that can be applied in horizontal oil shale formations. The process starts by feeding preheated air to oil shale to initiate a topochemical reaction and the onset of self-pyrolysis. As the temperature in the virgin oil shale increases (to 250–300°C), the hot air can be replaced by ambient-temperature air, allowing heat to be released by internal topochemical reactions to complete the pyrolysis. The propagation of fronts formed in this process, the temperature evolution, and the reaction mechanism of oil shale pyrolysis in porous media are discussed and compared with those in a traditional oxygen-free process. The results show that the self-pyrolysis of oil shale can be achieved with the proposed method without any need for external heat. The results also verify that fractured oil shale may be more suitable for underground retorting. Moreover, the gas and liquid products from this method were characterised, and a highly instrumented experimental device designed specifically for this process is described. This study can serve as a reference for new ideas on oil shale in situ pyrolysis processes. PMID:25656294

40 CFR 80.1426 - How are RINs generated and assigned to batches of renewable fuel by renewable fuel producers or...

Code of Federal Regulations, 2014 CFR

2014-07-01

... process energy 6 F Biodiesel, renewable diesel, jet fuel and heating oil Soy bean oil; Oil from annual... biomass and petroleum 4 G Biodiesel, heating oil Canola/Rapeseed oil Trans-Esterification using natural gas or biomass for process energy 4 H Biodiesel, renewable diesel, jet fuel and heating oil Soy bean...

Comparison of oil refining and biodiesel production process between screw press and n-hexane techniques from beauty leaf feedstock

NASA Astrophysics Data System (ADS)

Bhuiya, M. M. K.; Rasul, M. G.; Khan, M. M. K.; Ashwath, N.

2016-07-01

The Beauty Leaf Tree (Callophylum inophyllum) is regarded as an alternative source of energy to produce 2nd generation biodiesel due to its potentiality as well as high oil yield content in the seed kernels. The treating process is indispensable during the biodiesel production process because it can augment the yield as well as quality of the product. Oil extracted from both mechanical screw press and solvent extraction using n-hexane was refined. Five replications each of 25 gm of crude oil for screw press and five replications each of 25 gm of crude oil for n-hexane were selected for refining as well as biodiesel conversion processes. The oil refining processes consists of degumming, neutralization as well as dewaxing. The degumming, neutralization and dewaxing processes were performed to remove all the gums (phosphorous-based compounds), free fatty acids, and waxes from the fresh crude oil before the biodiesel conversion process carried out, respectively. The results indicated that up to 73% and 81% of mass conversion efficiency of the refined oil in the screw press and n-hexane refining processes were obtained, respectively. It was also found that up to 88% and 90% of biodiesel were yielded in terms of mass conversion efficiency in the transesterification process for the screw press and n-hexane techniques, respectively. While the entire processes (refining and transesterification) were considered, the conversion of beauty leaf tree (BLT) refined oil into biodiesel was yielded up to 65% and 73% of mass conversion efficiency for the screw press and n-hexane techniques, respectively. Physico-chemical properties of crude and refined oil, and biodiesel were characterized according to the ASTM standards. Overall, BLT has the potential to contribute as an alternative energy source because of high mass conversion efficiency.

Process concept of retorting of Julia Creek oil shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sitnai, O.

1984-06-01

A process is proposed for the above ground retorting of the Julia Creek oil shale in Queensland. The oil shale characteristics, process description, chemical reactions of the oil shale components, and the effects of variable and operating conditions on process performance are discussed. The process contains a fluidized bed combustor which performs both as a combustor of the spent shales and as a heat carrier generator for the pyrolysis step. 12 references, 5 figures, 5 tables.

ALL-UNION CONFERENCE ON APPLICATIONS OF RADIOACTIVE ISOTOPES AND NUCLEAR EMISSIONS IN THE NATIONAL INDUSTRY OF USSR (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1960-09-01

Papers presented at the All-Union Conference on Industrial Applications of Radioactive Isotopes and Nuclear Emissions in the National Economy of USSR, April 12 to 16, 1960, in Riga are surveyed. Short summaries are given on applications of radioactive isotopes and nuclear emissions in prospecting, developing mineral resources, metallurgy, ore enrichment processes, machine construction technology, agriculture, food processing, and medicine. Sources of alpha , beta , and gamma radiation for control and automation of processes are also discussed. The full reports from the conference will be published in 1960. (R.V.J.)

[The study of unions in demography: from categories to process].

PubMed

Burch, T K; Belanger, D

1999-01-01

For centuries, illegitimate children, those born outside of civil marriage or a marriage conducted within the church, were systematically accorded second-class status by both the law and religion. This attitude toward such children frustrates efforts to change legislation, social structure, and our understanding of new types of union outside of marriage. In Canada, no common term even exists in the two official languages to designate the cohabitation of an unmarried couple. Such unions simply fall through the net of classical demography. Even the more dynamic approaches, such as those seen in multistate models, follow only the movements of individuals in traditional categories. One must understand that the formation of couples is a multidimensional process and that a multidimensional approach to such unions could lead to the creation of a new group of nonethnocentric categories applicable to a number of different societies. The authors also consider the notion of process, in which marriage and cohabitation are merely two states in a range of possible states through which an individual will move during the course of his or her life. Cohabiting situations vary in importance depending upon one¿s states. Better demographic analyses can lead to greater understanding of the human couple and its sexual and reproductive behaviors.

Castor Oil: Properties, Uses, and Optimization of Processing Parameters in Commercial Production

PubMed Central

Patel, Vinay R.; Dumancas, Gerard G.; Kasi Viswanath, Lakshmi C.; Maples, Randall; Subong, Bryan John J.

2016-01-01

Castor oil, produced from castor beans, has long been considered to be of important commercial value primarily for the manufacturing of soaps, lubricants, and coatings, among others. Global castor oil production is concentrated primarily in a small geographic region of Gujarat in Western India. This region is favorable due to its labor-intensive cultivation method and subtropical climate conditions. Entrepreneurs and castor processors in the United States and South America also cultivate castor beans but are faced with the challenge of achieving high castor oil production efficiency, as well as obtaining the desired oil quality. In this manuscript, we provide a detailed analysis of novel processing methods involved in castor oil production. We discuss novel processing methods by explaining specific processing parameters involved in castor oil production. PMID:27656091

Castor Oil: Properties, Uses, and Optimization of Processing Parameters in Commercial Production.

PubMed

Patel, Vinay R; Dumancas, Gerard G; Kasi Viswanath, Lakshmi C; Maples, Randall; Subong, Bryan John J

2016-01-01

Castor oil, produced from castor beans, has long been considered to be of important commercial value primarily for the manufacturing of soaps, lubricants, and coatings, among others. Global castor oil production is concentrated primarily in a small geographic region of Gujarat in Western India. This region is favorable due to its labor-intensive cultivation method and subtropical climate conditions. Entrepreneurs and castor processors in the United States and South America also cultivate castor beans but are faced with the challenge of achieving high castor oil production efficiency, as well as obtaining the desired oil quality. In this manuscript, we provide a detailed analysis of novel processing methods involved in castor oil production. We discuss novel processing methods by explaining specific processing parameters involved in castor oil production.

Exploring the WTI crude oil price bubble process using the Markov regime switching model

NASA Astrophysics Data System (ADS)

Zhang, Yue-Jun; Wang, Jing

2015-03-01

The sharp volatility of West Texas Intermediate (WTI) crude oil price in the past decade triggers us to investigate the price bubbles and their evolving process. Empirical results indicate that the fundamental price of WTI crude oil appears relatively more stable than that of the market-trading price, which verifies the existence of oil price bubbles during the sample period. Besides, by allowing the WTI crude oil price bubble process to switch between two states (regimes) according to a first-order Markov chain, we are able to statistically discriminate upheaval from stable states in the crude oil price bubble process; and in most of time, the stable state dominates the WTI crude oil price bubbles while the upheaval state usually proves short-lived and accompanies unexpected market events.

The 1925 Fort Union Indian Congress: Divergent Narratives, One Event

ERIC Educational Resources Information Center

Blee, Lisa

2007-01-01

This essay investigates how various perspectives differ and converge in the span of an afternoon, thus illustrating how divergent narratives, through their very difference, enhance one's understanding of the past. The case study of the 1925 Fort Union Indian Congress points to the process of narrativizing experience and underscores how meaning is…

The Influence of Informal Power Structures on School Board-Teacher Union Contract Negotiations.

ERIC Educational Resources Information Center

Miller-Whitehead, Marie

A study examined behaviors of participants trained in a nonadversarial model of contract negotiation, focusing on possible influences of formal and informal power structures, written and unwritten rules, and firmly entrenched adversarial behavior on the bargaining process. Participants were representatives of a district's teacher union and board…

Empowering LGBTQ Youth in Europe: The Work of IGLYO

ERIC Educational Resources Information Center

Vella, Darren R.; Nowottnick, Lucy; Selun, Bruno; van Roozendaal, Bjorn

2009-01-01

Policy-making within the European Union is not a straightforward process. The International Lesbian, Gay, Bisexual, Transgender and Queer Youth and Student Organisation (IGLYO), through its work in the area of LGBTQ youth advocacy, has been continually developing strategies within the many policy-making structures located within the Union. One of…

What can the World Health Organization learn from EU lessons in civil society engagement and participation for health?

PubMed

Battams, Samantha

2014-01-01

This article explores challenges for and the development of civil society engagement and stakeholder representation, transparency, and accountability measures in the European Union, with a specific focus on health policy. The stance of the European Union on stakeholder participation within reform debates of the World Health Organization (WHO) is also considered, along with EU lessons for multi-stakeholders at the WHO. The European Commission has developed a number of measures for stakeholder engagement and transparency; however, the European Union has been prone to lobbying interests and has found difficulty in leading and making accountable the private sector when it comes to achieving its own health policy goals. The strong influence of corporate lobbyists on the European Union has come to light, with concerns about a lack of transparency and accountability in decision-making processes. While the WHO could learn from the European Union in terms of its strategies for stakeholder engagement, it could also heed some of the important lessons for the European Union when it comes to working with a broad range of stakeholders.

Biochemical upgrading of oils

DOEpatents

Premuzic, Eugene T.; Lin, Mow S.

1999-01-12

A process for biochemical conversion of heavy crude oils is provided. The process includes contacting heavy crude oils with adapted biocatalysts. The resulting upgraded oil shows, a relative increase in saturated hydrocarbons, emulsions and oxygenates and a decrease in compounds containing in organic sulfur, organic nitrogen and trace metals. Adapted microorganisms which have been modified under challenged growth processes are also disclosed.

40 CFR 80.1426 - How are RINs generated and assigned to batches of renewable fuel by renewable fuel producers or...

Code of Federal Regulations, 2013 CFR

2013-07-01

... annual covercrops Fermentation using natural gas, biomass, or biogas for process energy 6 F Biodiesel...-Esterification Hydrotreating Excluding processes that co-process renewable biomass and petroleum 4 G Biodiesel... Biodiesel, renewable diesel, jet fuel and heating oil Soy bean oil; Oil from annual covercrops; Algal oil...

Biochemical upgrading of oils

DOEpatents

Premuzic, E.T.; Lin, M.S.

1999-01-12

A process for biochemical conversion of heavy crude oils is provided. The process includes contacting heavy crude oils with adapted biocatalysts. The resulting upgraded oil shows, a relative increase in saturated hydrocarbons, emulsions and oxygenates and a decrease in compounds containing organic sulfur, organic nitrogen and trace metals. Adapted microorganisms which have been modified under challenged growth processes are also disclosed. 121 figs.

Processing use, and characterization of shale oil products

PubMed Central

Decora, Andrew W.; Kerr, Robert D.

1979-01-01

Oil shale is a potential source of oil that will supplement conventional sources for oil as our needs for fossil fuels begin to exceed our supplies. The resource may be mined and processed on the surface or it may be processed in situ. An overview of the potential technologies and environmental issues is presented. PMID:446454

Oxygen-Induced Cracking Distillation of Oil in the Continuous Flow Tank Reactor

ERIC Educational Resources Information Center

Shvets, Valeriy F.; Kozlovskiy, Roman A.; Luganskiy, Artur I.; Gorbunov, Andrey V.; Suchkov, Yuriy P.; Ushin, Nikolay S.; Cherepanov, Alexandr A.

2016-01-01

The article analyses problems of processing black oil fuel and addresses the possibility of increasing the depth of oil refining by a new processing scheme. The study examines various methods of increasing the depth of oil refining reveals their inadequacies and highlights a need to introduce a new method of processing atmospheric and vacuum…

Co-processing of carbonaceous solids and petroleum oil

DOEpatents

Gupta, Avinash; Greene, Marvin I.

1992-01-01

In a process for producing distillates from coal by a first stage thermal liquefaction followed by a catalytic hydrogenation, liquefaction solvent is added at points spaced over the length of the thermal liquefaction heater. Coal may be co-processed with petroleum oil by adding pre-hydrogenated oil to the first stage or unhydrogenated oil to the second stage.

Aerobic microbial enhanced oil recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Torsvik, T.; Gilje, E.; Sunde, E.

1995-12-31

In aerobic MEOR, the ability of oil-degrading bacteria to mobilize oil is used to increase oil recovery. In this process, oxygen and mineral nutrients are injected into the oil reservoir in order to stimulate growth of aerobic oil-degrading bacteria in the reservoir. Experiments carried out in a model sandstone with stock tank oil and bacteria isolated from offshore wells showed that residual oil saturation was lowered from 27% to 3%. The process was time dependent, not pore volume dependent. During MEOR flooding, the relative permeability of water was lowered. Oxygen and active bacteria were needed for the process to takemore » place. Maximum efficiency was reached at low oxygen concentrations, approximately 1 mg O{sub 2}/liter.« less

Prospects for applications of electron beams in processing of gas and oil hydrocarbons

NASA Astrophysics Data System (ADS)

Ponomarev, A. V.; Pershukov, V. A.; Smirnov, V. P.

2015-12-01

Waste-free processing of oil and oil gases can be based on electron-beam technologies. Their major advantage is an opportunity of controlled manufacturing of a wide range of products with a higher utility value at moderate temperatures and pressures. The work considers certain key aspects of electron beam technologies applied for the chain cracking of heavy crude oil, for the synthesis of premium gasoline from oil gases, and also for the hydrogenation, alkylation, and isomerization of unsaturated oil products. Electronbeam processing of oil can be embodied via compact mobile modules which are applicable for direct usage at distant oil and gas fields. More cost-effective and reliable electron accelerators should be developed to realize the potential of electron-beam technologies.

Coal liquefaction process solvent characterization and evaluation: Progress report, 1 April--30 June 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winschel, R. A.; Robbins, G. A.; Burke, F. P.

1986-11-01

Conoco Coal Research Division is characterizing samples of direct coal liquefaction process oils based on a variety of analytical techniques to provide a detailed description of the chemical composition of the oils to more fully understand the interrelationship of process oil composition and process operations, to aid in plant operation, and to lead to process improvements. The approach taken is to obtain analyses of a large number of well-defined process oils taken during periods of known operating conditions and known process performance. A set of thirty-one process oils from the Hydrocarbon Research, Inc. (HRI) Catalytic Two-Stage Liquefaction (CTSL) bench unitmore » was analyzed to provide information on process performance. The Fourier-Transform infrared (FTIR) spectroscopic method for the determination of phenolics in cola liquids was further verified. A set of four tetahydrofuran-soluble products from Purdue Research Foundation's reactions of coal/potassium/crown ether, analyzed by GC/MS and FTIR, were found to consist primarily of paraffins (excluding contaminants). Characterization data (elemental analyses, /sup 1/H-NMR and phenolic concentrations) were obtained on a set of twenty-seven two-stage liquefaction oils. Two activities were begun but not completed. First, analyses were started on oils from Wilsonville Run 250 (close- coupled ITSL). Also, a carbon isotopic method is being examined for utility in determining the relative proportion of coal and petroleum products in coprocessing oils.« less

Study on Handing Process and Quality Degradation of Oil Palm Fresh Fruit Bunches (FFB)

NASA Astrophysics Data System (ADS)

Mat Sharif, Zainon Binti; Taib, Norhasnina Binti Mohd; Yusof, Mohd Sallehuddin Bin; Rahim, Mohammad Zulafif Bin; Tobi, Abdul Latif Bin Mohd; Othman, Mohd Syafiq Bin

2017-05-01

The main objective of this study is to determine the relationship between quality of oil palm fresh fruit bunches (FFB) and handling processes. The study employs exploratory and descriptive design, with quantitative approach and purposive sampling using self-administrated questionnaires, were obtained from 30 smallholder respondents from the Southern Region, Peninsular Malaysia. The study reveals that there was a convincing relationship between quality of oil palm fresh fruit bunches (FFB) and handling processes. The main handling process factors influencing quality of oil palm fresh fruit bunches (FFB) were harvesting activity and handling at the plantation area. As a result, it can be deduced that the handling process factors variable explains 82.80% of the variance that reflects the quality of oil palm fresh fruit bunches (FFB). The overall findings reveal that the handling process factors do play a significant role in the quality of oil palm fresh fruit bunches (FFB).

Subsurface stratigraphy and oil fields in the Salem Limestone and associated rocks in Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, S.J.; Becker, L.E.

An area of 11 counties in southwestern Indiana was studied because (1) the subsurface geology of the Salem Limestone and associated rocks in the area contained numerous correlation discrepancies; (2) it was the locus of recent oil exploration and oil discoveries in these rocks; (3) the last subsurface study of this rock section was made in 1957; and (4) since that time, subsurface data from newly drilled petroleum-test wells have increased a hundredfold. Because of their abundance, geophysical logs were used extensively for correlation. Drill cuttings, where available, were also used in studying the rock units. The upper boundary ofmore » the Salem was based on geophysical-log correlations as supported by available drill cuttings. The lower boundary of the Salem was based on drill cuttings. Commercial oil is produced from porous calcarenite zones in the St. Louis and Salem Limestones and from coarsely crystalline limestone in the Harrodsburg Limestone. The lower part of the St. Louis Limestone yields oil from a porous carbonate rock that resembles Salem calcarenite and that we have formally named the Sission Member in the St. Louis. The Salem calcarenite facies ranges in thickness from a low of 10 percent of the total Salem in the southern part of the study area to a high of 80 percent in the northern part. Oil is produced from porous zones in the calcarenite. Oil production from the St. Louis, Salem, and Harrodsburg Limestones in Indiana amounted to 8,880,078 barrels as of December 31, 1978. Production in 1977 was 1,534,320 barrels, and production in 1978 was 1,157,450 barrels. About 80 percent of the 1977 and 1978 production came from Union-Bowman Consolidated and Sisson Fields in Gibson, Knox, and Pike counties and the Owensville North Consolidated and Mt. Carmel Consolidated Fields in Gibson County. 15 figures, 3 tables.« less

Processing of palm oil mill wastes based on zero waste technology

NASA Astrophysics Data System (ADS)

Irvan

2018-02-01

Indonesia is currently the main producer of palm oil in the world with a total production reached 33.5 million tons per year. In the processing of fresh fruit bunches (FFB) besides producing palm oil and kernel oil, palm oil mills also produce liquid and solid wastes. The increase of palm oil production will be followed by an increase in the production of waste generated. It will give rise to major environmental issues especially the discharge of liquid waste to the rivers, the emission of methane from digestion pond and the incineration of empty fruit bunches (EFB). This paper describes a zero waste technology in processing palm oil mill waste after the milling process. The technology involves fermentation of palm oil mill effluent (POME) to biogas by using continuous stirred tank reactor (CSTR) in the presence of thermophilic microbes, producing activated liquid organic fertilizer (ALOF) from discharge of treated waste effluent from biogas digester, composting EFB by spraying ALOF on the EFB in the composter, and producing pellet or biochar from EFB by pyrolysis process. This concept can be considered as a promising technology for palm oil mills with the main objective of eliminating the effluent from their mills.

Regulatory and associated political issues with respect to Bt transgenic maize in the European union.

PubMed

Saeglitz, Christiane; Bartsch, Detlef

2003-06-01

Legislation at the national level in Europe as well as that developed by the European Union (EU) generally permits release and commercialization of genetically modified organisms (GMOs). However, only 10 plant/event combinations were registered as of 2002: three maize events (Bt176, Mon810, and Bt11), with the other seven divided among carnation (3), oil-seed rape (2), tobacco (1), and raddiccio (1). Of these, only one maize event (Bt176) has been registered as a legal variety, and this was in Spain, where 22,000ha have been planted annually since 1998. In this paper, we first provide an overview on the complexity of EU GMO legislation. Then we discuss the minor role that results of EU-funded biosafety research have had on governmental policy. Finally, we provide information about initiatives for post-commercialization monitoring plans of Bt maize in Europe. As a result of the slow progress to date, we conclude that commercialization of GMOs will be seriously delayed in the EU for the next several years.

Glycidyl fatty acid esters in refined edible oils: A review on formation, occurrence, analysis, and elimination methods

USDA-ARS?s Scientific Manuscript database

Glycidyl fatty acid esters (GEs), one of the main contaminants in processed oil, are mainly formed during the deodorization step in the oil refining process of edible oils and therefore occur in almost all refined edible oils. GEs are potential carcinogens, due to the fact that they hydrolyze into t...

Processing liquid organic wastes at the NNL Preston laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coppersthwaite, Duncan; Greenwood, Howard; Docrat, Tahera

2013-07-01

Organic compounds of various kinds have been used in the nuclear industry for numerous duties in uranium chemical, metal and ceramic processing plants. In the course of the various operations undertaken, these organic compounds have become contaminated with uranic material, either accidentally or as an inevitable part of the process. Typically, the chemical/physical form and/or concentration of the uranic content of the organics has prevented disposal. In order to address the issue of contaminated liquid organic wastes, the National Nuclear Laboratory (NNL) has developed a suite of treatments designed to recover uranium and to render the waste suitable for disposal.more » The developed processes are operated at industrial scale via the NNL Preston Laboratory Residue Processing Plant. The Oil Waste Leaching (OWL) Process is a fully industrialised process used for the treatment of contaminated oils with approximately 200 tonnes of uranium contaminated oil being treated to date. The process was originally developed for the treatment of contaminated tributyl phosphate and odourless kerosene which had been adsorbed onto sawdust. However, over the years, the OWL process has been refined for a range of oils including 'water emulsifiable' cutting oils, lubricating oils, hydraulic oils/fluids and 'Fomblin' (fully fluorinated) oils. Chemically, the OWL process has proved capable of treating solvents as well as oils but the highly volatile/flammable nature of many solvents has required additional precautions compared with those required for oil treatment. These additional precautions led to the development of the Solvent Treatment Advanced Rig (STAR), an installation operated under an inert atmosphere. STAR is a small 'module' (100 dm{sup 3} volume) which allows the treatment of both water miscible and immiscible solvents. This paper discusses the challenges associated with the treatment of liquid organic wastes and the process developments which have allowed a wide range of materials to be successfully treated. (authors)« less

Effect of oil content and kernel processing of corn silage on digestibility and milk production by dairy cows.

PubMed

Weiss, W P; Wyatt, D J

2000-02-01

Corn silages were produced from a high oil corn hybrid and from its conventional hybrid counterpart and were harvested with a standard silage chopper or a chopper equipped with a kernel processing unit. High oil silages had higher concentrations of fatty acids (5.5 vs. 3.4% of dry matter) and crude protein (8.4 vs. 7.5% of dry matter) than the conventional hybrid. Processed silage had larger particle size than unprocessed silage, but more starch was found in small particles for processed silage. Dry matter intake was not influenced by treatment (18.4 kg/d), but yield of fat-corrected milk (23.9 vs. 22.6 kg/d) was increased by feeding high oil silage. Overall, processing corn silage did not affect milk production, but cows fed processed conventional silage tended to produce more milk than did cows fed unprocessed conventional silage. Milk protein percent, but not yield, was reduced with high oil silage. Milk fat percent, but not yield, was higher with processed silage. Overall, processed silage had higher starch digestibility, but the response was much greater for the conventional silage hybrid. The concentration of total digestible nutrients (TDN) tended to be higher for diets with high oil silage (71.6 vs. 69.9%) and tended to be higher for processed silage than unprocessed silage (71.7 vs. 69.8%), but an interaction between variety and processing was observed. Processing conventional corn silage increased TDN to values similar to high oil corn silage but processing high oil corn silage did not influence TDN.

Non-catalytic alcoholysis process for production of biodiesel fuel by using bubble column reactor

NASA Astrophysics Data System (ADS)

Hagiwara, S.; Nabetani, H.; Nakajima, M.

2015-04-01

Biodiesel fuel is a replacement for diesel as a fuel produced from biomass resources. It is usually defined as a fatty acid methyl ester (FAME) derived from vegetable oil or animal fat. In European countries, such as Germany and France, biodiesel fuel is commercially produced mainly from rapeseed oil, whereas in the United States and Argentina, soybean oil is more frequently used. In many other countries such as Japan and countries in Southeast Asia, lipids that cannot be used as a food source could be more suitable materials for the production of biodiesel fuel because its production from edible oils could result in an increase in the price of edible oils, thereby increasing the cost of some foodstuffs. Therefore, used edible oil, lipids contained in waste effluent from the oil milling process, byproducts from oil refining process and crude oils from industrial crops such as jatropha could be more promising materials in these countries. The materials available in Japan and Southeast Asia for the production of biodiesel fuel have common characteristics; they contain considerable amount of impurities and are high in free fatty acids (FFA). Superheated methanol vapor (SMV) reactor might be a promising method for biodiesel fuel production utilizing oil feedstock containing FFA such as waste vegetable oil and crude vegetable oil. In the conventional method using alkaline catalyst, FFA contained in waste vegetable oil is known to react with alkaline catalyst such as NaOH and KOH generating saponification products and to inactivate it. Therefore, the FFA needs to be removed from the feedstock prior to the reaction. Removal of the alkaline catalyst after the reaction is also required. In the case of the SMV reactor, the processes for removing FFA prior to the reaction and catalyst after the reaction can be omitted because it requires no catalyst. Nevertheless, detailed study on the productivity of biodiesel fuel produced from waste vegetable oils and other non-edible lipids by use of the SMV reactor has not been examined yet. Therefore, this study aims to investigate the productivity of biodiesel produced from waste vegetable oils using the SMV reactor. Biodiesel fuel is a replacement for diesel as a fuel produced from biomass resources. It is generally produced as a FAME derived from vegetable oil by using alkaline catalyzed alcoholysis process. This alkaline method requires deacidification process prior to the reaction process and the alkaline catalyst removal process after the reaction. Those process increases the total cost of biodiesel fuel production. In order to solve the problems in the conventional alkaline catalyzed alcoholysis process, the authors proposed a non-catalytic alcoholysis process called the Superheated Methanol Vapor (SMV) method with bubble column reactor. So, this study aims to investigate the productivity of biodiesel produced from vegetable oils and other lipids using the SMV method with bubble column reactor.

The role of union democracy in the struggle for workers' health in Mexico.

PubMed

Laurell, A C

1989-01-01

In this article, the author analyzes the struggle for workers' health in Mexico, emphasizing the importance of the general and specific political context. In an overview of the legislation on industrial health and safety, the state institutions involved in the issue, and the characteristics of union organization in Mexico, the author shows that the limited activities related to workers' health have more to do with the relative political weakness of the Mexican working class than with the formal structures of legislation, state institutions, and unions. The second part of the article deals with the four most important struggles for health and safety in Mexico during the last ten years, which show some similarities. These struggles are consistently linked to processes of union democratization and tend to decline when union democracy is lost. The strategies of the companies show a common pattern: removing health issues from collective bargaining and putting them in the hands of state institutions. When workers have opposed this solution, management has used selective repression to solve the conflict. The state institutions subordinate their position to the companies' by postponing action or by doing a technically poor job. Changing the existing situation involves the social legitimation of the workers' health issue, since this would have an impact on the political processes involved, i.e., corporate control over workers, authoritarian labor relations and professionalism, and resources of the state institutions.

The Unions and the Relaunching of European Social Policy

ERIC Educational Resources Information Center

Guasconi, Maria Eleonora

2004-01-01

The question of European trade unions' approach towards vocational training is an interesting example of a broader issue, involving both the role played by non-governmental actors in shaping the social dimension of the integration process, and the need to develop a social dialogue in the Community. In this context, the establishment of Cedefop in…

The National Status of the Preparation of School Psychologists in Estonia

ERIC Educational Resources Information Center

Kikas, Eve

2014-01-01

Estonia is a small republic that has undergone several big societal changes (from belonging to the Soviet Union to becoming a free republic, and the process of integrating into the European Union) during the last several decades. Psychology has been taught as a separate discipline starting from 1968, but its content has been changed from very…

Stating the Obvious: The European Qualifications Framework is "Not" a Neutral Evidence-Based Policy Tool

ERIC Educational Resources Information Center

Cort, Pia

2010-01-01

In European Union policy documents, the European Qualifications Framework (EQF) is described as a neutral tool embedded in an evidence-based policy process. Its purpose is to improve the transparency, comparability and portability of qualifications in the European Union. The aim of this article is to denaturalise the EQF discourse through a…

Successful Negotiation in Schools: Management, Unions, Employees, and Citizens.

ERIC Educational Resources Information Center

Herman, Jerry J.; Herman, Janice L.

This book is a how-to-do-it roadmap that presents practical details on the important aspects of collective bargaining at the local school district level. It details all of the strategies, tasks, events, and influences that bear on the collective bargaining process from the initial certification election of a union through the preparation for…

Risky Sexual Behaviors in Immigrant Adolescent Girls from the Former Soviet Union: Role of Natal and Host Culture

ERIC Educational Resources Information Center

Jeltova, Ida; Fish, Marian C.; Revenson, Tracey A.

2005-01-01

In recent years, schools have been increasingly involved in youth's health-related behavior, particularly risky health behaviors (e.g., HIV/AIDS and pregnancy prevention programs). This study examined how acculturation processes among adolescent girls who are recent immigrants from the former Soviet Union (FSU) affect their practices of risky…

Processes for washing a spent ion exchange bed and for treating biomass-derived pyrolysis oil, and apparatuses for treating biomass-derived pyrolysis oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baird, Lance Awender; Brandvold, Timothy A.

Processes and apparatuses for washing a spent ion exchange bed and for treating biomass-derived pyrolysis oil are provided herein. An exemplary process for washing a spent ion exchange bed employed in purification of biomass-derived pyrolysis oil includes the step of providing a ion-depleted pyrolysis oil stream having an original oxygen content. The ion-depleted pyrolysis oil stream is partially hydrotreated to reduce the oxygen content thereof, thereby producing a partially hydrotreated pyrolysis oil stream having a residual oxygen content that is less than the original oxygen content. At least a portion of the partially hydrotreated pyrolysis oil stream is passed throughmore » the spent ion exchange bed. Water is passed through the spent ion exchange bed after passing at least the portion of the partially hydrotreated pyrolysis oil stream therethrough.« less

Integrated oil production and upgrading using molten alkali metal

DOEpatents

Gordon, John Howard

2016-10-04

A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

A combined microwave pretreatment/solvent extraction process for the production of oil from palm fruit: optimisation, oil quality and effect of prolonged exposure.

PubMed

Tan, Jason Cx; Chuah, Cheng-Hock; Cheng, Sit-Foon

2017-04-01

Conventional palm oil milling involves multiple stages after fruit collection; in particular, oil clarification introduces water into the pressed oil, which results in a large quantity of wastewater. A combined process of microwave pretreatment and solvent extraction to mill crude palm oil, without introducing water or steam, is described. An excellent yield (up to 30%) of oil was obtained with pretreatment in a 42 L, 1000 W and 2450 MHz microwave oven followed by hexane extraction. The optimum conditions (10 min microwave pretreatment and 12 h solvent extraction) yielded an oil with a low free fatty acid content (<1.0%) and an acceptable anisidine value (<3.0 meq kg -1 ). The oil had a fatty acid composition not resembling those of conventional crude palm oil and crude palm kernel oil. In the pretreatment, the leached oil had 6.3% lauric acid whereas the solvent extracted oil had only 1.5% lauric acid. Among the factors affecting the oil quality, microwave pretreatment affected the oil quality significantly; however, an optimised duration that would ensure high efficiency in solvent extraction also resulted in ruptured fruitlets, although not to the extent of causing excessive oxidation. In fact, microwave pretreatment should exceed 12 min; after only 15 min, the oil had 1-methylcyclopentanol (12.96%), 1-tetradecanol (9.44%), 1-nonadecene (7.22%), nonanal (7.13%) and 1-tridecene (5.09%), which probably arose from the degradation of fibres. Microwave pretreatment represents an alternative milling process for crude palm oil compared with conventional processes in the omission of wet treatment with steam. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Corrosion considerations for thermochemical biomass liquefaction process systems in biofuel production

DOE PAGES

Brady, Michael P.; Keiser, James R.; Leonard, Donovan N.; ...

2014-11-11

Thermochemical liquifaction processing of biomass to produce bio-derived fuels (e.g. gasoline, jet fuel, diesel, home heating oil, etc.) is of great recent interest as a renewable energy source. Approaches under investigation include direct liquefaction, hydrothermal liquefaction, hydropyrolysis, fast pyrolysis, etc. to produce energy dense liquids that can be utilized as produced or further processed to provide products of higher value. An issue with bio-oils is that they tend to contain significant concentrations of organic compounds, which make the bio-oil acidic and a potential source of corrosion issues in in transport, storage, and use. Efforts devoted to modified/further processing of bio-oilsmore » to make them less corrosive are currently being widely pursued. Another aspect that must also be addressed is potential corrosion issues in the bio-oil liquefaction process equipment itself. Depending on the specific process, bio-oil liquefaction production temperatures can reach up to 400-600 °C, and involve the presence of aggressive sulfur, and halide species from both the biomass used and/or process additives. Detailed knowledge of the corrosion resistance of candidate process equipment alloys in these bio-oil production environments is currently lacking. Lastly, this paper summarizes our recent, ongoing efforts to assess the extent to which corrosion of bio-oil process equipment may be an issue, with the ultimate goal of providing the basis to select the lowest cost alloy grades capable of providing the long-term corrosion resistance needed for future bio-oil production plants.« less

Removal of Free Fatty Acid from Plant Oil by the Adsorption Process

NASA Astrophysics Data System (ADS)

Chung, Tsair-Wang; Wu, Yi-Ling; Hsu, Shih-Hong

2018-05-01

The food oil refinery process for deacidification is ususally conducted by the neutralization after degumming. In this study, commercialized resins will be used as adsorbents to remove the free fatty acid (FFA) in food oil without using any solvent. Applying this environmental friendly green process, the energy efficiency will be increased and the waste water will be reduced compared to the traditional process. The selected adsorbent can be reused which may reduce the process cost. Instead of using alkali neutralization, the proposed process may reduce the concern of food oil security. The commercial resins A26OH and IRA900Cl were compared as adsorbents to remove the FFA in deacidification for refinery of food oil without adding any alkali chemicals. This process will be conducted to remove the FFA form peanut oil in this study. Besides, this study will get the adsorption isotherms for one of the better sorbents of A26OH or IRA900Cl to remove FFA from peanut oil under 25, 35, and 45°C. The Langmuir and Freundlich isotherm models were compared to fit the experimental data. The obtained isotherm data is important for the adsorption system design.

Artisanal Extraction and Traditional Knowledge Associated with Medicinal Use of Crabwood Oil (Carapa guianensis Aublet.) in a Peri-Urban Várzea Environment in the Amazon Estuary.

PubMed

Nardi, Mariane; Lira-Guedes, Ana Cláudia; Albuquerque Cunha, Helenilza Ferreira; Guedes, Marcelino Carneiro; Mustin, Karen; Gomes, Suellen Cristina Pantoja

2016-01-01

Várzea forests of the Amazon estuary contain species of importance to riverine communities. For example, the oil extracted from the seeds of crabwood trees is traditionally used to combat various illnesses and as such artisanal extraction processes have been maintained. The objectives of this study were to (1) describe the process involved in artisanal extraction of crabwood oil in the Fazendinha Protected Area, in the state of Amapá; (2) characterise the processes of knowledge transfer associated with the extraction and use of crabwood oil within a peri-urban riverine community; and (3) discern medicinal uses of the oil. The data were obtained using semistructured interviews with 13 community members involved in crabwood oil extraction and via direct observation. The process of oil extraction is divided into four stages: seed collection; cooking and resting of the seeds; shelling of the seeds and dough preparation; and oil collection. Oil extraction is carried out within the home for personal use, with surplus marketed within the community. More than 90% of the members of the community involved in extraction of crabwood oil highlighted the use of the oil to combat inflammation of the throat. Knowledge transfer occurs via oral transmission and through direct observation.

Catalytic cracking of the top phase fraction of bio-oil into upgraded liquid oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sunarno; Chemical Engineering Department, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur,Yogyakarta 55281; Rochmadi,

The energy consumption is increasing, while oil reserves as a primary energy resource are decreasing, so that is the reason seeking alternative energy source is inevitable. Biomass especially oil palm empty fruit bunches (EFB) which is abundant in Indonesia can be processed into bio-oil by pyrolysis process. The potential for direct substitution of bio-oil for petroleum may be limited due to the high viscosity, high oxygen content, low heating value, and corrosiveness. Consequently, upgrading of the bio-oil before use is inevitable to give a wider variety of applications of its liquid product. Furthermore, upgrading process to improve the quality ofmore » bio-oil by reduction of oxygenates involves process such as catalytic cracking. The objective of this research is to study the effect of operation temperature on yield and composition of upgraded liquid oil and to determine physical properties. Bio-oil derived from EFB was upgraded through catalytic cracking using series tubular reactor under atmospheric pressure on a silica-alumina catalyst. Results show that increasing temperature from 450 to 600 °C, resulting in decreasing of upgraded liquid oil (ULO) yield, decreasing viscosity and density of ULO, but increasing in calorimetric value of ULO. The increasing temperature of cracking also will increase the concentration of gasoline and kerosene in ULO.« less

Artisanal Extraction and Traditional Knowledge Associated with Medicinal Use of Crabwood Oil (Carapa guianensis Aublet.) in a Peri-Urban Várzea Environment in the Amazon Estuary

PubMed Central

Lira-Guedes, Ana Cláudia; Albuquerque Cunha, Helenilza Ferreira; Guedes, Marcelino Carneiro; Mustin, Karen; Gomes, Suellen Cristina Pantoja

2016-01-01

Várzea forests of the Amazon estuary contain species of importance to riverine communities. For example, the oil extracted from the seeds of crabwood trees is traditionally used to combat various illnesses and as such artisanal extraction processes have been maintained. The objectives of this study were to (1) describe the process involved in artisanal extraction of crabwood oil in the Fazendinha Protected Area, in the state of Amapá; (2) characterise the processes of knowledge transfer associated with the extraction and use of crabwood oil within a peri-urban riverine community; and (3) discern medicinal uses of the oil. The data were obtained using semistructured interviews with 13 community members involved in crabwood oil extraction and via direct observation. The process of oil extraction is divided into four stages: seed collection; cooking and resting of the seeds; shelling of the seeds and dough preparation; and oil collection. Oil extraction is carried out within the home for personal use, with surplus marketed within the community. More than 90% of the members of the community involved in extraction of crabwood oil highlighted the use of the oil to combat inflammation of the throat. Knowledge transfer occurs via oral transmission and through direct observation. PMID:27478479

The formation process and responsive impacts of single oil droplet in submerged process.

PubMed

Li, Haoshuai; Meng, Long; Shen, Tiantian; Zhang, Jianrui; Bao, Mutai; Sun, Peiyan

2017-11-15

Simulated column was applied to research forming progress of single oil droplet in submerged process, floating progress, and study effects of environment factors and dispersants on the concentration of oil hydrocarbon in water as well as changing rules of oil droplet sizes. As expected, particular formation mechanism of single oil droplet was presented. When necking down length L is 0.5 time of oil droplet diameter (d) after expansion phase, necking down becomes long and thin; when L=2d, necking down begins to break. In floating progress, the shape changes oval and its motion trail becomes an auger-type. Fluctuation occurs at horizontal direction. Dispersants decrease oil droplet size by its dispersion effect, and cut down effect of Van Der Waals force among oil droplets. More broadly, these findings provide rare empirical evidence expounding formation mechanism of single oil droplet to increasing ability of oil spill response. Copyright © 2017 Elsevier Ltd. All rights reserved.

Treatment of vegetable oily wastewater using an integrated microfiltration-reverse osmosis system.

PubMed

Yu, Xiaoli; Zhong, Zhaoxiang; Xing, Weihong

2010-01-01

Vegetable oil processing plants and catering trade often generate a large amount of oil-containing wastewater, which causes serious environmental problems. The objective of this work was to explore the feasibility of vegetable oil wastewater treatment with an integrated microfiltration-reverse osmosis (MF-RO) process. The influence of operational parameters on the separation behaviors were investigated in MF process. In MF continuous process the steady flux was around 90 (L/m(2) h) when the concentrated multiple reached 16, and the oil content in permeate was less than 12 mg/L. In the RO continuous process, antifouling membrane was used to treat permeate from the ceramic membrane process in order to improve the water quality. The RO process had a permeate flux of 24 (L/m(2) h) and water recovery rate of 95%. The permeate from the RO stage was free of oil, and its TOC and conductivity were less than 0.6 mg/L and 50 micros/cm, respectively. The results demonstrated that the two stage membrane process combining MF and RO is highly efficient in the treatment of oil-containing wastewater.

Burning crude oil without pollution

NASA Technical Reports Server (NTRS)

Houseman, J.

1979-01-01

Crude oil can be burned at drilling sites by two-stage combustion process without producing pollution. Process allows easier conformance to strict federal or state clean air standards without installation of costly pollution removal equipment. Secondary oil recovery can be accomplished with injection of steam heating by burning oil.

Literature review on production process to obtain extra virgin olive oil enriched in bioactive compounds. Potential use of byproducts as alternative sources of polyphenols.

PubMed

Frankel, Edwin; Bakhouche, Abdelhakim; Lozano-Sánchez, Jesús; Segura-Carretero, Antonio; Fernández-Gutiérrez, Alberto

2013-06-05

This review describes the olive oil production process to obtain extra virgin olive oil (EVOO) enriched in polyphenol and byproducts generated as sources of antioxidants. EVOO is obtained exclusively by mechanical and physical processes including collecting, washing, and crushing of olives, malaxation of olive paste, centrifugation, storage, and filtration. The effect of each step is discussed to minimize losses of polyphenols from large quantities of wastes. Phenolic compounds including phenolic acids, alcohols, secoiridoids, lignans, and flavonoids are characterized in olive oil mill wastewater, olive pomace, storage byproducts, and filter cake. Different industrial pilot plant processes are developed to recover phenolic compounds from olive oil byproducts with antioxidant and bioactive properties. The technological information compiled in this review will help olive oil producers to improve EVOO quality and establish new processes to obtain valuable extracts enriched in polyphenols from byproducts with food ingredient applications.

A many-body dissipative particle dynamics study of forced water-oil displacement in capillary.

PubMed

Chen, Chen; Zhuang, Lin; Li, Xuefeng; Dong, Jinfeng; Lu, Juntao

2012-01-17

The forced water-oil displacement in capillary is a model that has important applications such as the groundwater remediation and the oil recovery. Whereas it is difficult for experimental studies to observe the displacement process in a capillary at nanoscale, the computational simulation is a unique approach in this regard. In the present work, the many-body dissipative particle dynamics (MDPD) method is employed to simulate the process of water-oil displacement in capillary with external force applied by a piston. As the property of all interfaces involved in this system can be manipulated independently, the dynamic displacement process is studied systematically under various conditions of distinct wettability of water in capillary and miscibility between water and oil as well as of different external forces. By analyzing the dependence of the starting force on the properties of water/capillary and water/oil interfaces, we find that there exist two different modes of the water-oil displacement. In the case of stronger water-oil interaction, the water particles cannot displace those oil particles sticking to the capillary wall, leaving a low oil recovery efficiency. To minimize the residual oil content in capillary, enhancing the wettability of water and reducing the external force will be beneficial. This simulation study provides microscopic insights into the water-oil displacement process in capillary and guiding information for relevant applications. © 2011 American Chemical Society

Development of a highly efficient oil degumming process using a novel phosphatidylinositol-specific phospholipase C enzyme.

PubMed

Cerminati, Sebastián; Eberhardt, Florencia; Elena, Claudia E; Peirú, Salvador; Castelli, María E; Menzella, Hugo G

2017-06-01

Enzymatic degumming using phospholipase C (PLC) enzymes may be used in environmentally friendly processes with improved oil recovery yields. In this work, phosphatidylinositol-specific phospholipase C (PIPLC) candidates obtained from an in silico analysis were evaluated for oil degumming. A PIPLC from Lysinibacillus sphaericus was shown to efficiently remove phosphatidylinositol from crude oil, and when combined with a second phosphatidylcholine and phosphatidylethanolamine-specific phospholipase C, the three major phospholipids were completely hydrolyzed, providing an extra yield of oil greater than 2.1%, compared to standard methods. A remarkably efficient fed-batch Escherichia coli fermentation process producing ∼14 g/L of the recombinant PIPLC enzyme was developed, which may facilitate the adoption of this cost-effective oil-refining process.

Dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) for the prediction of non-union consolidation.

PubMed

Fischer, Christian; Nissen, Mareike; Schmidmaier, Gerhard; Bruckner, Thomas; Kauczor, Hans-Ulrich; Weber, Marc-André

2017-02-01

Non-union perfusion can be visualized with dynamic contrast-enhanced (DCE) MRI. This study evaluated DCE-MRI to predict non-union consolidation after surgery and detect factors that affect bone healing. Between 2010 and 2015 non-union perfusion was prospectively quantified in 205 patients (mean age, 51.5 years, 129 men, 76 women) before intervention and at 6, 12, 26, 52 and more weeks follow-up. DCE-MRI results were related to the osseous consolidation, the ability to predict successful outcome was estimated by ROC analysis. The relevance of the body mass index (BMI) and the non-union severity score (NUSS) to the healing process was assessed. Tibial (n=99) and femoral (n=76) non-unions were most common. Consolidation could be assessed in 169 patients, of these 103 (61%) showed eventual healing and demonstrated higher perfusion than in failed consolidation at 6 (p=0.0226), 12 (p=0.0252) and 26 (p=0.0088) weeks follow-up. DCE-MRI at 26 weeks follow-up predicted non-union consolidation with a sensitivity of 75% and a specificity of 87% (false classification rate 19%). Higher BMI (p=0.041) and NUSS (p<0.0001) were associated with treatment failure. DCE-MRI perfusion analysis after non-union surgery predicts successful outcome and could facilitate the decision of early intervention. NUSS and BMI are important prognostic factors concerning consolidation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hadean silicate differentiation revealed by anomalous 142Nd in the Réunion hotspot source

NASA Astrophysics Data System (ADS)

Peters, B. J.; Carlson, R.; Day, J. M.; Horan, M.

2017-12-01

Geochemical and geophysical data show that volcanic hotspots can tap ancient domains sequestered in Earth's deep mantle. Evidence from stable and long-lived radiogenic isotope systems has demonstrated that many of these domains result from tectonic and differentiation processes that occurred more than two billion years ago. Recent advances in the analysis of short-lived radiogenic isotopes have further shown that some hotspot sources preserve evidence for metal-silicate differentiation occurring within the first one percent of Earth's history. Despite these discoveries, efforts to detect variability in the lithophile 146Sm-142Nd (t1/2 = 103 Ma) system in Phanerozoic hotspot lavas have not yet detected significant global variation. We report 142Nd/144Nd ratios in Réunion Island basalts that are statistically distinct from the terrestrial Nd standard ranging to both higher and lower 142Nd/144Nd. Variations in 142Nd/144Nd, which total nearly 15 ppm on Réunion, are correlated with 3He/4He among both anomalous and non-anomalous samples. Such behavior implies that there were analogous changes in Sm/Nd and (U+Th)/3He that occurred during a Hadean silicate differentiation event and were not completely overprinted by the depleted mantle. Variations in the 142Nd-143Nd compositions of Réunion basalts can be explained by a single Hadean melting event producing enriched and depleted domains that partially re-mixed after 146Sm was no longer extant. Assuming differentiation occurred at pressures where perovskite is stable, anomalies of the magnitude observed in Réunion basalts require melting of at least 50% across a wide depth range, and up to 90% for melting at pressures near those of the deepest mantle. Models with best fits to Nd isotope data suggest this differentiation occurred around 4.40 Ga and mixing occurred after 4 Ga. This two-stage differentiation process nearly erased the ancient, anomalous 142Nd composition of the Réunion source and produced the relatively invariant 143Nd signature that is a hallmark of Réunion hotspot lavas. Given growing evidence that the Réunion hotspot source represents an unusually ancient, primitive mantle domain, these new data argue that Réunion is a critical source of information regarding the formation and preservation of ancient heterogeneities in Earth's deep interior.

International Power Institute`s quarterly technical progress report, July--September 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coles, J.E.

1998-10-30

The International Power Institute (IPI) at Morehouse College has organized a team to design and create a Short Term Training Program for ESKOM Union Leaders which will last four weeks and take place at a location in South Africa to be designated by ESKOM. This proposal envisions a group of no more than 25 union leaders to be trained at the same time but the program could be expanded to accommodate up to 40 trainees. The program is designed around interactive training with lectures followed by discussion, case studies, trainee work groups, homework assignments and two field study visits. Also,more » the program is designed to have a number of ESKOM management people join the course for one day in the second week and one day at the end, in each case after a half day of preparation in separate sessions from the union leaders, to share with the trainees expectations and, at the end of the program, their course experiences. In addition, IPI has prepared a follow on proposal for a Long Term Training Program. This LT program is specified in less detail but can be expanded based on future discussions with ESKOM management. The training program is designed with the following objectives: determine and identify the most pressing problems facing ESKOM Union Leadership in their relationship with management; instill in the union leadership a heightened sense of purpose and willingness to take ownership of a process that will increase effective outcomes of meaningful, good faith bargaining; develop skills and experience leading to improved union administration; enhance realistic expectations and improve process knowledge to facilitate future labor negotiations and grievance proceedings; and provide participants with enhanced skills and knowledge to develop and/or strengthen a functioning, democratic work culture and structure internal to the union.« less

Geotechnical Properties of Oil Shale Retorted by the PARAHO and TOSCO Processes.

DTIC Science & Technology

1979-11-01

literature search was restricted to the Green River formation of oil shale in the tri-state area of Colorado (Piceance Basin ), Utah ( Uinta Basin ), and...it is preheated by combustion gases as it travels downward by gravity. Air and recycling gas are injected at midheight and are burned, bringing the oil ...REFERENCES..................................38 TABLES 1-5 APPENDIX A: OIL SHALE RETORTING PROCESSES................Al Tosco Process Gas Combustion

Steam distillation extraction of ginger essential oil: Study of the effect of steam flow rate and time process

NASA Astrophysics Data System (ADS)

Fitriady, Muhammad Arifuddin; Sulaswatty, Anny; Agustian, Egi; Salahuddin, Aditama, Deska Prayoga Fauzi

2017-01-01

In Indonesia ginger was usually used as a seasoning for dishes, an ingredient for beverage and a source of herbal medicines. Beside raw usage, ginger can be processed to obtain the essential oil which has many advantages such as proven to be an active antimicrobial and having an antioxidant ability. There are a lot of methods to extract essential oil from ginger, one of which is steam distillation. The aim of the current study was to investigate the effect of variation of time process and steam flow rate in the yield on ginger essential oil steam distillation extraction process. It was found that the best operation condition was 0.35 ml/s as the steam flow rate which yields 2.43% oil. The optimum time process was predicted at 7.5 hours. The composition of the oil was varied depend on the flow rate and every flow rate has its own major component contained in the oil. Curcumene composition in the oil was increased as increased steam flow rate applied, but the composition of camphene was decreased along with the increasing steam flow rate.

Mild Biomass Liquefaction Process for Economic Production of Stabilized Refinery-Ready Bio-oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gangwal, Santosh; Meng, Jiajia; McCabe, Kevin

Southern Research (SR) in cooperation with U.S. Department of Energy (DOE), Bioenergy Technology Office (BETO), investigated a biomass liquefaction process for economic production of stabilized refinery-ready bio-oil. The project was awarded by DOE under a Funding Opportunity Announcement (DE-FOA-0000686) for Bio-oil Stabilization and Commoditization that intended to evaluate the feasibility of using bio-oil as a potential feedstock in an existing petroleum refinery. SR investigated Topic Area 1 of the FOA at Technology Readiness Level 2-3 to develop thermochemical liquefaction technologies for producing a bio-oil feedstock from high-impact biomass that can be utilized within a petroleum refinery. Bio-oil obtained from fastmore » pyrolysis of biomass is a green intermediate that can be further upgraded into a biofuel for blending in a petroleum refinery using a hydro-deoxygenation (HDO) route. Co-processing pyrolysis bio-oil in a petroleum refinery is an attractive approach to leverage the refinery’s existing capital. However, the petroleum industry is reluctant to accept pyrolysis bio-oil because of a lack of a standard definition for an acceptable bio-oil feedstock in existing refinery processes. Also per BETO’s multiyear program plan, fast pyrolysis-based bio-fuel is presently not cost competitive with petroleum-based transportation fuels. SR aims to develop and demonstrate a cost-effective low-severity thermal liquefaction and hydrodeoxygenation (HDO) process to convert woody biomass to stabilized bio-oils that can be directly blended with hydrotreater input streams in a petroleum refinery for production of gasoline and/or diesel range hydrocarbons. The specific project objectives are to demonstrate the processes at laboratory scale, characterize the bio-oil product and develop a plan in partnership with a refinery company to move the technology towards commercialization.« less

Learning together, working together: an evaluation of experiences of a pilot programme for partnership between unions and management in the health service.

PubMed

Young, Pat; Moule, Pam; Evans, David; Simmons, Sue; Crack, Meg; Mayo, Gillian

2012-07-01

This article describes an innovative initiative to support partnership working between trade unions and management in three National Health Service Trusts, by means of shared participation in a series of learning and development days. Although there is existing evidence, within the literature on partnership, of the benefits of partnership working for employees and employers, there is little discussion of processes by which effective partnership is developed. More specifically, there is no current academic literature on the role of education in enabling improved partnership working between trade unions and managers. The findings of the evaluation suggest that the pilot provided a successful learning experience as well as a number of pointers for improving future developments of this nature. The recommendations include embedding of partnership work within existing staff development processes. Copyright © 2011 Elsevier Ltd. All rights reserved.

Mobility and Migration of Labour in the European Union and Their Specific Implications for Young People. CEDEFOP Document.

ERIC Educational Resources Information Center

Tassinopoulos, Alexandros; Werner, Heinz; Kristensen, Soren

This document contains two papers that examine mobility and migration of labor in the European Union and discuss specific implications for young people. The "Foreword" (Jordi Planas) examines the practical and symbolic role that establishment of the right to freedom of movement for European citizens plays in the process of construction…

On a Molecular Basis, Investigate Association of Molecular Structure with Bioactive Compounds, Anti-Nutritional Factors and Chemical and Nutrient Profiles of Canola Seeds and Co-Products from Canola Processing: Comparison Crusher Plants within Canada and within China as well as between Canada and China.

PubMed

Gomaa, Walaa M S; Mosaad, Gamal M; Yu, Peiqiang

2018-04-21

The objectives of this study were to: (1) Use molecular spectroscopy as a novel technique to quantify protein molecular structures in relation to its chemical profiles and bioenergy values in oil-seeds and co-products from bio-oil processing. (2) Determine and compare: (a) protein molecular structure using Fourier transform infrared (FT/IR-ATR) molecular spectroscopy technique; (b) bioactive compounds, anti-nutritional factors, and chemical composition; and (c) bioenergy values in oil seeds (canola seeds), co-products (meal or pellets) from bio-oil processing plants in Canada in comparison with China. (3) Determine the relationship between protein molecular structural features and nutrient profiles in oil-seeds and co-products from bio-oil processing. Our results showed the possibility to characterize protein molecular structure using FT/IR molecular spectroscopy. Processing induced changes between oil seeds and co-products were found in the chemical, bioenergy profiles and protein molecular structure. However, no strong correlation was found between the chemical and nutrient profiles of oil seeds (canola seeds) and their protein molecular structure. On the other hand, co-products were strongly correlated with protein molecular structure in the chemical profile and bioenergy values. Generally, comparisons of oil seeds (canola seeds) and co-products (meal or pellets) in Canada, in China, and between Canada and China indicated the presence of variations among different crusher plants and bio-oil processing products.

European integration in crisis? Of supranational integration, hegemonic projects and domestic politics

PubMed Central

Bulmer, Simon; Joseph, Jonathan

2015-01-01

The European Union is facing multiple challenges. Departing from mainstream theory, this article adopts a fresh approach to understanding integration. It does so by taking two theoretical steps. The first introduces the structure–agency debate in order to make explicit the relationship between macro-structures, the institutional arrangements at European Union level and agency. The second proposes that the state of integration should be understood as the outcome of contestation between competing hegemonic projects that derive from underlying social processes and that find their primary expression in domestic politics. These two steps facilitate an analysis of the key areas of contestation in the contemporary European Union, illustrated by an exploration of the current crisis in the European Union, and open up the development of an alternative, critical, theory of integration. PMID:29708125

Mixed Integer Linear Programming model for Crude Palm Oil Supply Chain Planning

NASA Astrophysics Data System (ADS)

Sembiring, Pasukat; Mawengkang, Herman; Sadyadharma, Hendaru; Bu'ulolo, F.; Fajriana

2018-01-01

The production process of crude palm oil (CPO) can be defined as the milling process of raw materials, called fresh fruit bunch (FFB) into end products palm oil. The process usually through a series of steps producing and consuming intermediate products. The CPO milling industry considered in this paper does not have oil palm plantation, therefore the FFB are supplied by several public oil palm plantations. Due to the limited availability of FFB, then it is necessary to choose from which plantations would be appropriate. This paper proposes a mixed integer linear programming model the supply chain integrated problem, which include waste processing. The mathematical programming model is solved using neighborhood search approach.

Application of petroleum demulsification technology to shale oil emulsions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, R.E.

1983-01-01

Demulsification, the process of emulsion separation, of water-in-oil shale oil emulsions produced by several methods was accomplished using commercial chemical demulsifiers which are used typically for petroleum demulsification. The shale oil emulsions were produced from Green River shale by one in situ and three different above-ground retorts, an in situ high pressure/high temperature steam process, and by washing both retort-produced and hydrotreated shale oils.

MERCURY IN CRUDE OIL PROCESSED IN THE UNITED STATES (2004)

EPA Science Inventory

The mean and range of concentrations of mercury in crude oil processed in the U.S. were investigated using two analytical methods. The sample ensemble consisted of 329 samples from 170 separate crude oil streams that are processed by U.S. refineries. Samples were retrieved imme...

Potential uses for cuphea oil processing byproducts and processed oils

USDA-ARS?s Scientific Manuscript database

Cuphea spp. has seeds that contain high levels of medium chain fatty acids and have the potential to be commercially cultivated. In the course of processing and refining Cuphea oil a number of bi-products are generated. Developing commercial uses for these bi-products would improve the economics of...

78 FR 143 - Desert Mining, Inc., Eagle Broadband, Inc., Endovasc, Inc., Environmental Oil Processing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-02

... SECURITIES AND EXCHANGE COMMISSION [File No. 500-1] Desert Mining, Inc., Eagle Broadband, Inc., Endovasc, Inc., Environmental Oil Processing Technology Corp., Falcon Ridge Development, Inc., Fellows... Environmental Oil Processing Technology Corp. because it has not filed any periodic reports since the period...

The extraction of bitumen from western oil sands. Annual report, July 1991--July 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.

1992-08-01

The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximatelymore » 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report.« less

Core flooding tests to investigate the effects of IFT reduction and wettability alteration on oil recovery during MEOR process in an Iranian oil reservoir.

PubMed

Rabiei, Arash; Sharifinik, Milad; Niazi, Ali; Hashemi, Abdolnabi; Ayatollahi, Shahab

2013-07-01

Microbial enhanced oil recovery (MEOR) refers to the process of using bacterial activities for more oil recovery from oil reservoirs mainly by interfacial tension reduction and wettability alteration mechanisms. Investigating the impact of these two mechanisms on enhanced oil recovery during MEOR process is the main objective of this work. Different analytical methods such as oil spreading and surface activity measurements were utilized to screen the biosurfactant-producing bacteria isolated from the brine of a specific oil reservoir located in the southwest of Iran. The isolates identified by 16S rDNA and biochemical analysis as Enterobacter cloacae (Persian Type Culture Collection (PTCC) 1798) and Enterobacter hormaechei (PTCC 1799) produce 1.53 g/l of biosurfactant. The produced biosurfactant caused substantial surface tension reduction of the growth medium and interfacial tension reduction between oil and brine to 31 and 3.2 mN/m from the original value of 72 and 29 mN/m, respectively. A novel set of core flooding tests, including in situ and ex situ scenarios, was designed to explore the potential of the isolated consortium as an agent for MEOR process. Besides, the individual effects of wettability alteration and IFT reduction on oil recovery efficiency by this process were investigated. The results show that the wettability alteration of the reservoir rock toward neutrally wet condition in the course of the adsorption of bacteria cells and biofilm formation are the dominant mechanisms on the improvement of oil recovery efficiency.

Process for preparing lubricating oil from used waste lubricating oil

DOEpatents

Whisman, Marvin L.; Reynolds, James W.; Goetzinger, John W.; Cotton, Faye O.

1978-01-01

A re-refining process is described by which high-quality finished lubricating oils are prepared from used waste lubricating and crankcase oils. The used oils are stripped of water and low-boiling contaminants by vacuum distillation and then dissolved in a solvent of 1-butanol, 2-propanol and methylethyl ketone, which precipitates a sludge containing most of the solid and liquid contaminants, unspent additives, and oxidation products present in the used oil. After separating the purified oil-solvent mixture from the sludge and recovering the solvent for recycling, the purified oil is preferably fractional vacuum-distilled, forming lubricating oil distillate fractions which are then decolorized and deodorized to prepare blending stocks. The blending stocks are blended to obtain a lubricating oil base of appropriate viscosity before being mixed with an appropriate additive package to form the finished lubricating oil product.

Types of Refined Petroleum Products

EPA Pesticide Factsheets

These are derived from crude oils through processes such as catalytic cracking and fractional distillation. Examples described here are gasoline, kerosene, no. 2 fuel oil, no. 4 fuel oil, no. 5 fuel oil, no. 6 fuel oil, and lubricating oil.

Analysis of edible oil processing options for the BIO-Plex advanced life support system

NASA Technical Reports Server (NTRS)

Greenwalt, C. J.; Hunter, J.

2000-01-01

Edible oil is a critical component of the proposed plant-based Advanced Life Support (ALS) diet. Soybean, peanut, and single-cell oil are the oil source options to date. In terrestrial manufacture, oil is ordinarily extracted with hexane, an organic solvent. However, exposed solvents are not permitted in the spacecraft environment or in enclosed human tests by National Aeronautics and Space Administration due to their potential danger and handling difficulty. As a result, alternative oil-processing methods will need to be utilized. Preparation and recovery options include traditional dehulling, crushing, conditioning, and flaking, extrusion, pressing, water extraction, and supercritical extraction. These processing options were evaluated on criteria appropriate to the Advanced Life Support System and BIO-Plex application including: product quality, product stability, waste production, risk, energy needs, labor requirements, utilization of nonrenewable resources, usefulness of by-products, and versatility and mass of equipment to determine the most appropriate ALS edible oil-processing operation.

Production and Characterization of Ethyl Ester from Crude Jatropha curcas Oil having High Free Fatty Acid Content

NASA Astrophysics Data System (ADS)

Kumar, Rajneesh; Dixit, Anoop; Singh, Shashi Kumar; Singh, Gursahib; Sachdeva, Monica

2015-09-01

The two step process was carried out to produce biodiesel from crude Jatropha curcas oil. The pretreatment process was carried out to reduce the free fatty acid content by (≤2 %) acid catalyzed esterification. The optimum reaction conditions for esterification were reported to be 5 % H2SO4, 20 % ethanol and 1 h reaction time at temperature of 65 °C. The pretreatment process reduced the free fatty acid of oil from 7 to 1.85 %. In second process, alkali catalysed transesterification of pretreated oil was carried and the effects of the varying concentrations of KOH and ethanol: oil ratios on percent ester recovery were investigated. The optimum reaction conditions for transesterification were reported to be 3 % KOH (w/v of oil) and 30 % (v/v) ethanol: oil ratio and reaction time 2 h at 65 °C. The maximum percent recovery of ethyl ester was reported to be 60.33 %.

Microfluidics: an enabling screening technology for enhanced oil recovery (EOR).

PubMed

Lifton, Victor A

2016-05-21

Oil production is a critical industrial process that affects the entire world population and any improvements in its efficiency while reducing its environmental impact are of utmost societal importance. The paper reviews recent applications of microfluidics and microtechnology to study processes of oil extraction and recovery. It shows that microfluidic devices can be useful tools in investigation and visualization of such processes used in the oil & gas industry as fluid propagation, flooding, fracturing, emulsification and many others. Critical macro-scale processes that define oil extraction and recovery are controlled by the micro-scale processes based on wetting, adhesion, surface tension, colloids and other concepts of microfluidics. A growing number of research efforts demonstrates that microfluidics is becoming, albeit slowly, an accepted methodology in this area. We propose several areas of development where implementation of microfluidics may bring about deeper understanding and hence better control over the processes of oil recovery based on fluid propagation, droplet generation, wettability control. Studies of processes such as hydraulic fracturing, sand particle propagation in porous networks, high throughput screening of chemicals (for example, emulsifiers and surfactants) in microfluidic devices that simulate oil reservoirs are proposed to improve our understanding of these complicated physico-chemical systems. We also discuss why methods of additive manufacturing (3D printing) should be evaluated for quick prototyping and modification of the three-dimensional structures replicating natural oil-bearing rock formations for studies accessible to a wider audience of researchers.

Process for removing heavy metal compounds from heavy crude oil

DOEpatents

Cha, Chang Y.; Boysen, John E.; Branthaver, Jan F.

1991-01-01

A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

Characterization of seed oils from fresh Bokbunja (Rubus coreanus Miq.) and wine processing waste.

PubMed

Ku, C S; Mun, S P

2008-05-01

The physicochemical characteristics, fatty acid (FA) profile, and triacylglyceride (TAG) composition of seed oils from fresh Bokbunja (Rubus coreanus Miq.) fruits and traditional Bokbunja wine processing waste were determined in this study. Oil contents of the fresh seeds and the seeds from wine processing waste were similar, accounting for about 18% of dry weight. The free fatty acid (FFA) content between the two seed oils was significantly different (0.50% for fresh seed oil and 73.14% for wine seed oil). Iodine, conjugated diene, saponification values, and unsaponifiable matter were very similar in the oil samples, but the specific extinction coefficients at 232 and 270 nm of wine seed oil were higher than those of fresh seed oil. Linoleic (C18:2, 50.45-53.18%, L) and linolenic (C18:3, 29.36-33.25%, Ln) acids were the dominant FAs in the two seed oils, whereas oleic (C18:1, 7.32-8.04%, O), palmitic (C16:0, 1.55-1.65%, P), and stearic (C18:0, 0.65-0.68%, S) acids were the minor FAs. LLL, OLL, LLLn, OOL, LLnLn, and OOO were the abundant TAGs, representing >90% of the oils.

Catalytic processes towards the production of biofuels in a palm oil and oil palm biomass-based biorefinery.

PubMed

Chew, Thiam Leng; Bhatia, Subhash

2008-11-01

In Malaysia, there has been interest in the utilization of palm oil and oil palm biomass for the production of environmental friendly biofuels. A biorefinery based on palm oil and oil palm biomass for the production of biofuels has been proposed. The catalytic technology plays major role in the different processing stages in a biorefinery for the production of liquid as well as gaseous biofuels. There are number of challenges to find suitable catalytic technology to be used in a typical biorefinery. These challenges include (1) economic barriers, (2) catalysts that facilitate highly selective conversion of substrate to desired products and (3) the issues related to design, operation and control of catalytic reactor. Therefore, the catalytic technology is one of the critical factors that control the successful operation of biorefinery. There are number of catalytic processes in a biorefinery which convert the renewable feedstocks into the desired biofuels. These include biodiesel production from palm oil, catalytic cracking of palm oil for the production of biofuels, the production of hydrogen as well as syngas from biomass gasification, Fischer-Tropsch synthesis (FTS) for the conversion of syngas into liquid fuels and upgrading of liquid/gas fuels obtained from liquefaction/pyrolysis of biomass. The selection of catalysts for these processes is essential in determining the product distribution (olefins, paraffins and oxygenated products). The integration of catalytic technology with compatible separation processes is a key challenge for biorefinery operation from the economic point of view. This paper focuses on different types of catalysts and their role in the catalytic processes for the production of biofuels in a typical palm oil and oil palm biomass-based biorefinery.

Separation of oil-water-sludge emulsions coming from palm oil mill process through microwave techniques.

PubMed

Pérez-Páez, Rocío; Catalá-Civera, José Manuel; García-Baños, Beatriz; Castillo, Edgar F; Bastos, Johanna M; Zambrano, Luz S

2008-01-01

The palm oil mills extraction process requires the separation of oil-water-sludge emulsions. For this purpose, the use of sedimentation and/or centrifugation techniques have been required until now. However, significant losses persist in different process flows and new methods are needed to further decrease them, such as methods based on electromagnetic waves application. In the study, emulsions obtained from two flow processes, namely press liquor stream (PL) and recovered stream of the centrifugal step (RC), were exposed to microwave radiation with different exposure times. In the case of the press liquor stream, different oil/water dilution ratios were also studied. The sedimentation speed and efficiency were studied for the irradiated samples and compared to those obtained for the same fluids with no radiation. Also, chromatographic tests were performed on the recovered oil to determine the effect on the oil quality after microwave radiation. The obtained results allow us to conclude that microwave exposure during periods below 1 minute lead to better sedimentation speed and efficiency. It was observed that microwaves facilitate the break of the charges and polarities balances in the emulsions at considerably lower temperatures than the corresponding in the conventional process, without affecting the recovered oil quality.

Effect of sodium carbonate catalyst weight on production of bio-oil via thermochemical liquefaction of corncobs in ethanol-water solution

NASA Astrophysics Data System (ADS)

Sembodo, Bregas Siswahjono Tatag; Sulistyo, Hary; Sediawan, Wahyudi Budi; Fahrurrozi, Mohammad

2018-02-01

Lignocellulosic biomass has recently received serious attention as an energy source that can replace fossil fuels. Corncob is one of lignocellulosic biomass wastes, which can be further processed into bio-oil through thermochemical liquefaction process. Bio-oil is expected to be further processed into fuel oil. In this research the effect of Na2CO3 catalyst weight on the yield of bio-oil was investigated. The composition of bio-oil produced in this process was analyzed by GC-MS. Bio-oil formation rate were analyzed through mathematical model development. First model aasumed as an isothermal process, while second model was not. It is found that both models were able to provide a good approach to experimental data. The average reaction rate constants was obtained from isothermal model, while the activation energy level and collision factors were obtained from non-isothermal model. The reaction rate will increase by addition of Na2CO3 (0 - 0.5 g) as catalyst to 250 mL system solution, then the activation energy will decrease from 1964.265 joules/mole to 1029.994 joules/mole. The GC-MS analysis results showed that the bio-oil were contained of ester compounds, phenolic compounds, cyclic compunds, heterocyclic compounds, and poly-alcohols compounds.

Performance of photocatalyst based carbon nanodots from waste frying oil in water purification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aji, Mahardika Prasetya, E-mail: mahardika190@gmail.com; Wiguna, Pradita Ajeng; Susanto,

Carbon Nanodots (C-Dots) from waste frying oil could be used as a photocatalyst in water purification with solar light irradiation. Performance of C-Dots as a photocatalyst was tested in the process of water purification with a given synthetic sewage methylene blue. The tested was also conducted by comparing the performance C-Dots made from frying oil, waste fryng oil as a photocatalyst and solution of methylene blue without photocatalyst C-Dots. Performance of C-Dots from waste frying oil were estimated by the results of absorbance spectrum. The results of measurement absorbance spectrum from the process of water purification with photocatalyst C-Dots showedmore » that the highest intensity at a wavelength 664 nm of methylene blue decreased. The test results showed that the performance of photocatalyst C-Dots from waste frying oil was better in water purification. This estimated that number of particles C-dots is more in waste frying oil because have experieced repeated the heating process so that the higher particles concentration make the photocatalyst process more effective. The observation of the performance C-Dots from waste frying oil as a photocatalyst in the water purification processes become important invention for solving the problems of waste and water purification.« less

Study on Energy Productivity Ratio (EPR) at palm kernel oil processing factory: case study on PT-X at Sumatera Utara Plantation

NASA Astrophysics Data System (ADS)

Haryanto, B.; Bukit, R. Br; Situmeang, E. M.; Christina, E. P.; Pandiangan, F.

2018-02-01

The purpose of this study was to determine the performance, productivity and feasibility of the operation of palm kernel processing plant based on Energy Productivity Ratio (EPR). EPR is expressed as the ratio of output to input energy and by-product. Palm Kernel plan is process in palm kernel to become palm kernel oil. The procedure started from collecting data needed as energy input such as: palm kernel prices, energy demand and depreciation of the factory. The energy output and its by-product comprise the whole production price such as: palm kernel oil price and the remaining products such as shells and pulp price. Calculation the equality of energy of palm kernel oil is to analyze the value of Energy Productivity Ratio (EPR) bases on processing capacity per year. The investigation has been done in Kernel Oil Processing Plant PT-X at Sumatera Utara plantation. The value of EPR was 1.54 (EPR > 1), which indicated that the processing of palm kernel into palm kernel oil is feasible to be operated based on the energy productivity.

A Process of Amplification of the Contributions of the Interfaith Ministry in the Student Affairs Division of Union College

ERIC Educational Resources Information Center

Brooks, Victoria J.

2009-01-01

This project examines the contributions of Interfaith Ministry to Union College with the hope of amplifying, or "turning up the volume" of this work in this ministry setting. Grounded in the historical realities of a small liberal arts college, the work explores models of chaplaincy in higher education on this specific campus and beyond.…

Microbial enhanced oil recovery: Entering the log phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bryant, R.S.

1995-12-31

Microbial enhanced oil recovery (MEOR) technology has advanced internationally since 1980 from a laboratory-based evaluation of microbial processes to field applications. In order to adequately support the decline in oil production in certain areas, research on cost-effective technologies such as microbial enhanced oil recovery processes must focus on both near-term and long-term applications. Many marginal wells are desperately in need of an inexpensive improved oil recovery technology today that can assist producers in order to prevent their abandonment. Microbial enhanced waterflooding technology has also been shown to be an economically feasible technology in the United States. Complementary environmental research andmore » development will also be required to address any potential environmental impacts of microbial processes. In 1995 at this conference, the goal is to further document and promote microbial processes for improved oil recovery and related technology for solving environmental problems.« less

Torrefaction reduction of coke formation on catalysts used in esterification and cracking of biofuels from pyrolysed lignocellulosic feedstocks

DOEpatents

Kastner, James R; Mani, Sudhagar; Hilten, Roger; Das, Keshav C

2015-11-04

A bio-oil production process involving torrefaction pretreatment, catalytic esterification, pyrolysis, and secondary catalytic processing significantly reduces yields of reactor char, catalyst coke, and catalyst tar relative to the best-case conditions using non-torrefied feedstock. The reduction in coke as a result of torrefaction was 28.5% relative to the respective control for slow pyrolysis bio-oil upgrading. In fast pyrolysis bio-oil processing, the greatest reduction in coke was 34.9%. Torrefaction at 275.degree. C. reduced levels of acid products including acetic acid and formic acid in the bio-oil, which reduced catalyst coking and increased catalyst effectiveness and aromatic hydrocarbon yields in the upgraded oils. The process of bio-oil generation further comprises a catalytic esterification of acids and aldehydes to generate such as ethyl levulinate from lignified biomass feedstock.

Fast pyrolysis oil from pinewood chips co-processing with vacuum gas oil in an FCC unit for second generation fuel production

DOE PAGES

Pinho, Andrea de Rezende; de Almeida, Marlon B. B.; Mendes, Fabio Leal; ...

2016-10-15

Raw bio-oil produced from fast pyrolysis of pine woodchips was co-processed with standard Brazilian vacuum gasoil (VGO) and tested in a 200 kg•h -1 fluid catalytic cracking (FCC) demonstration-scale unit using a commercial FCC equilibrium catalyst. Two different bio-oil/VGO weight ratios were used: 5/95 and 10/90. Co-processing of raw bio-oil in FCC was shown to be technically feasible. Bio-oil could be directly co-processed with a regular gasoil FCC feed up to 10 wt%. The bio-oil and the conventional gasoil were cracked into valuable liquid products such as gasoline and diesel range products. Most of the oxygen present in the bio-oilmore » was eliminated as water and carbon monoxide as these yields were always higher than that of carbon dioxide. Product quality analysis shows that trace oxygenates, primarily alkyl phenols, in FCC gasoline and diesel products are present with or without co-processing oxygenated intermediates. The oxygenate concentrations increase with co-processing, but have not resulted in increased concerns with quality of fuel properties. The presence of renewable carbon was confirmed in gasoline and diesel cuts through 14C isotopic analysis, showing that renewable carbon is not only being converted into coke, CO, and CO 2, but also into valuable refining liquid products. Thus, gasoline and diesel could be produced from lignocellulosic raw materials through a conventional refining scheme, which uses the catalytic cracking process. As a result, the bio-oil renewable carbon conversion into liquid products (carbon efficiency) was approximately 30%, well above the efficiency found in literature for FCC bio-oil upgrading.« less

Fast pyrolysis oil from pinewood chips co-processing with vacuum gas oil in an FCC unit for second generation fuel production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinho, Andrea de Rezende; de Almeida, Marlon B. B.; Mendes, Fabio Leal

Raw bio-oil produced from fast pyrolysis of pine woodchips was co-processed with standard Brazilian vacuum gasoil (VGO) and tested in a 200 kg•h -1 fluid catalytic cracking (FCC) demonstration-scale unit using a commercial FCC equilibrium catalyst. Two different bio-oil/VGO weight ratios were used: 5/95 and 10/90. Co-processing of raw bio-oil in FCC was shown to be technically feasible. Bio-oil could be directly co-processed with a regular gasoil FCC feed up to 10 wt%. The bio-oil and the conventional gasoil were cracked into valuable liquid products such as gasoline and diesel range products. Most of the oxygen present in the bio-oilmore » was eliminated as water and carbon monoxide as these yields were always higher than that of carbon dioxide. Product quality analysis shows that trace oxygenates, primarily alkyl phenols, in FCC gasoline and diesel products are present with or without co-processing oxygenated intermediates. The oxygenate concentrations increase with co-processing, but have not resulted in increased concerns with quality of fuel properties. The presence of renewable carbon was confirmed in gasoline and diesel cuts through 14C isotopic analysis, showing that renewable carbon is not only being converted into coke, CO, and CO 2, but also into valuable refining liquid products. Thus, gasoline and diesel could be produced from lignocellulosic raw materials through a conventional refining scheme, which uses the catalytic cracking process. As a result, the bio-oil renewable carbon conversion into liquid products (carbon efficiency) was approximately 30%, well above the efficiency found in literature for FCC bio-oil upgrading.« less

Synthesis of pH-sensitive and recyclable magnetic nanoparticles for efficient separation of emulsified oil from aqueous environments

NASA Astrophysics Data System (ADS)

Lü, Ting; Zhang, Shuang; Qi, Dongming; Zhang, Dong; Vance, George F.; Zhao, Hongting

2017-02-01

Emulsified oil wastewaters, arisen from oil industry and oil spill accidents, cause severe environmental and ecological problems. In this study, a series of pH-sensitive magnetic nanomaterials (MNPs) were synthesized and characterized for their evaluation in separation of emulsified oil from aqueous environments. A coprecipitation method was used to produce Fe3O4 magnetic nanoparticles that were coated in a 2-step process with first silica to form a surface for anchoring an (3-aminopropyl)triethoxysilane (APTES) molecular layer. Detailed studies were conducted on effects of MNPs dosage, APTES anchoring density (DA) and pH on oil-water separation performance of the synthetic MNPs. Results showed that, under both acidic and neutral conditions, MNPs with high DA exhibited enhanced oil-water separation performance, while under alkaline condition, the oil-water separation process was minimal. Alkaline conditions allowed the MNPs to be recycled up to 9 cycles without showing any significant decrease in oil-water separation efficiency. An examination of the oil-water separation mechanism found that electrostatic interaction and interfacial activity both played important roles in oil-water separation. In conclusion, pH-sensitive MNPs can be easily synthesized and recycled, providing a promising, cost-effective and environmentally-friendly process for the efficient treatment of emulsified oil wastewater.

Stabilization of Softwood-Derived Pyrolysis Oils for Continuous Bio-oil Hydroprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olarte, Mariefel V.; Zacher, Alan H.; Padmaperuma, Asanga B.

The use of fast pyrolysis as a potential renewable liquid transportation fuel alternative to crude oil depends on successful catalytic upgrading to produce a refinery-ready product with oxygen content and qualities (i.e. specific functional group or compound content) that is compatible with the product’s proposed insertion point. Catalytic upgrading of bio-oil requires high temperature and pressure, while similar to crude oil hydrotreating, is not as straightforward for the thermally unstable pyrolysis oil. For years, a two-temperature zone, downflow trickle bed reactor was the state-of-the art for continuous operation. However, pressure excursion due to plug formation still occurred, typically at themore » high temperature transition zone, leading to a process shutdown within 140 h. Recently, a bio-oil pre-treatment process, together with a robust commercial catalyst, was found to be enabling the continuous operation of the two-zone hydroprocessing system. Here, we report the results on pre-treating bio-oil at 413 K and 8.4 MPa of flowing H2 (500 L H2/L bio-oil, 0.5 L bio-oil/L catalyst bed) and the attempts to characterize this oil product to understand the chemistry which enabled the long-term processing of bio-oil.« less

Co-processing of olive bagasse with crude rapeseed oil via pyrolysis.

PubMed

Uçar, Suat; Karagöz, Selhan

2017-05-01

The co-pyrolysis of olive bagasse with crude rapeseed oil at different blend ratios was investigated at 500ºC in a fixed bed reactor. The effect of olive bagasse to crude rapeseed oil ratio on the product distributions and properties of the pyrolysis products were comparatively investigated. The addition of crude rapeseed oil into olive bagasse in the co-pyrolysis led to formation of upgraded biofuels in terms of liquid yields and properties. While the pyrolysis of olive bagasse produced a liquid yield of 52.5 wt %, the highest liquid yield of 73.5 wt % was obtained from the co-pyrolysis of olive bagasse with crude rapeseed oil at a blend ratio of 1:4. The bio-oil derived from olive bagasse contained 5% naphtha, 10% heavy naphtha, 30% gas oil, and 55% heavy gas oil. In the case of bio-oil obtained from the co-pyrolysis of olive bagasse with crude rapeseed oil at a blend ratio of 1:4, the light naphtha, heavy naphtha, and light gas oil content increased. This is an indication of the improved characteristics of the bio-oil obtained from the co-processing. The heating value of bio-oil from the pyrolysis of olive bagasse alone was 34.6 MJ kg -1 and the heating values of bio-oils obtained from the co-pyrolysis of olive bagasse with crude rapeseed oil ranged from 37.6 to 41.6 MJ kg -1 . It was demonstrated that the co-processing of waste biomass with crude plant oil is a good alternative to improve bio-oil yields and properties.

Getty Oil Company Diatomite project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuber, I.L.

1984-09-01

The feasibility of using Diatomite as a synthetic fuels feedstock is discussed. The asphaltic outcropping near McKittrick, California are evidence of oil bearing deposits. Two different processes have been taken to the pilot plant stage to evaluate the viability of recovering oil from the Diatomite ore. One approach was the retorting process which was developed by Lurgi. The other process is based on a totally different concept of solvent extracting the oil from the ore. The operation and performance of the pilot plants are described.

Co-composting of rose oil processing waste with caged layer manure and straw or sawdust: effects of carbon source and C/N ratio on decomposition.

PubMed

Onursal, Emrah; Ekinci, Kamil

2015-04-01

Rose oil is a specific essential oil that is produced mainly for the cosmetics industry in a few selected locations around the world. Rose oil production is a water distillation process from petals of Rosa damascena Mill. Since the oil content of the rose petals of this variety is between 0.3-0.4% (w/w), almost 4000 to 3000 kg of rose petals are needed to produce 1 kg of rose oil. Rose oil production is a seasonal activity and takes place during the relatively short period where the roses are blooming. As a result, large quantities of solid waste are produced over a limited time interval. This research aims: (i) to determine the possibilities of aerobic co-composting as a waste management option for rose oil processing waste with caged layer manure; (ii) to identify effects of different carbon sources - straw or sawdust on co-composting of rose oil processing waste and caged layer manure, which are both readily available in Isparta, where significant rose oil production also takes place; (iii) to determine the effects of different C/N ratios on co-composting by the means of organic matter decomposition and dry matter loss. Composting experiments were carried out by 12 identical laboratory-scale composting reactors (60 L) simultaneously. The results of the study showed that the best results were obtained with a mixture consisting of 50% rose oil processing waste, 64% caged layer manure and 15% straw wet weight in terms of organic matter loss (66%) and dry matter loss (38%). © The Author(s) 2015.

Converting solid wastes into liquid fuel using a novel methanolysis process.

PubMed

Xiao, Ye; He, Peng; Cheng, Wei; Liu, Jacqueline; Shan, Wenpo; Song, Hua

2016-03-01

Biomass fast pyrolysis followed by hydrodeoxygenation upgrading is the most popular way to produce upgraded bio-oil from biomass. This process requires large quantities of expensive hydrogen and operates under high pressure condition (70-140 atm). Therefore, a novel methanolysis (i.e., biomass pyrolysis under methane environment) process is developed in this study, which is effective in upgraded bio-oil formation at atmospheric pressure and at about 400-600°C. Instead of using pure methane, simulated biogas (60% CH4+40% CO2) was used to test the feasibility of this novel methanolysis process for the conversion of different solid wastes. The bio-oil obtained from canola straw is slightly less than that from sawdust in term of quantity, but the oil quality from canola straw is better in terms of lower acidity, lower Bromine Number, higher H/C atomic ratio and lower O/C atomic ratio. The municipal solid waste and newspaper can also obtain relatively high oil yields, but the oil qualities of them are both lower than those from sawdust and canola straw. Compared with catalysts of 5%Zn/ZSM-5 and 1%Ag/ZSM-5, the 5%Zn-1%Ag/ZSM-5 catalyst performed much better in terms of upgraded bio-oil yield as well as oil quality. During the methanolysis process, the metal silver may be used to reduce the total acid number of the oil while the metal zinc might act to decrease the bromine number of the oil. The highly dispersed Zn and Ag species on/in the catalyst benefit the achievement of better upgrading performance and make it be a very promising catalyst for bio-oil upgrading by biogas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enterobacter cloacae as biosurfactant producing bacterium: differentiating its effects on interfacial tension and wettability alteration Mechanisms for oil recovery during MEOR process.

PubMed

Sarafzadeh, Pegah; Hezave, Ali Zeinolabedini; Ravanbakhsh, Moosa; Niazi, Ali; Ayatollahi, Shahab

2013-05-01

Microbial enhanced oil recovery (MEOR) process utilizes microorganisms or their metabolites to mobilize the trapped oil in the oil formation after primary and secondary oil recovery stages. MEOR technique is considered as more environmentally friendly and low cost process. There are several identified mechanisms for more oil recovery using MEOR processes however; wettability alteration and interfacial tension (IFT) reduction are the important ones. Enterobacter Cloacae, a facultative bio-surfactant producer bacterium, was selected as a bacterial formulation due to its known performance on IFT reduction and wettability alteration. To quantify the effects of these two mechanisms, different tests including oil spreading, in situ and ex situ core flooding, wettability measurement (Amott), IFT, viscosity and pH measurements were performed. The obtained results revealed that the experimental procedure used in this study was able to quantitatively identify the individual effects of both mechanisms on the ultimate microbial oil recovery. The results demonstrated considerable effects of both mechanisms on the tertiary oil recovery; however after a proper shut in time period, more tertiary oil was recovered because of wettability alteration mechanism. Finally, SEM images taken from the treated cores showed biofilm formation on the rock pore surfaces, which is responsible for rock surface wettability alteration. Copyright © 2013 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Nigel; Lodge, Mike; Hilton, Linda

The nuclear industry is not a provider of oils and solvents but uses them in motors, equipment and even in chemical processes to extract valuable products. Currently, for old and contaminated oils and solvents, techniques still exist, such as incineration, but not all the oils and solvents are compatible with this technique because the activities of some components inside the oils are too high to be accepted at the incineration facility. For these oils, an alternative technique needs to be found for treatment. A process developed for water treatment using a technique of adsorption coupled with electrochemical regeneration has beenmore » investigated to assess its capability to treat these organic wastes. One of the strengths of the process is its flexibility and adaptation to different compositions of oils. This point is important because, in the AREVA case, there are a lot of small volumes of old oils which need to be re-characterized. It takes time and money to do it especially when oils are contaminated; this is one reason why the technique is interesting to investigate. Tests have been performed with different oils coming from different sites to test the feasibility. Results demonstrate the destruction of a range of organics with regeneration energy requirements of 13.4 - 68.7 kWh/l and offer confidence for the future potential of the process. (authors)« less

A Novel Way to Relate Ontology Classes

PubMed Central

Choksi, Ami T.; Jinwala, Devesh C.

2015-01-01

The existing ontologies in the semantic web typically have anonymous union and intersection classes. The anonymous classes are limited in scope and may not be part of the whole inference process. The tools, namely, the pellet, the jena, and the protégé, interpret collection classes as (a) equivalent/subclasses of union class and (b) superclasses of intersection class. As a result, there is a possibility that the tools will produce error prone inference results for relations, namely, sub-, union, intersection, equivalent relations, and those dependent on these relations, namely, complement. To verify whether a class is complement of other involves utilization of sub- and equivalent relations. Motivated by the same, we (i) refine the test data set of the conference ontology by adding named, union, and intersection classes and (ii) propose a match algorithm to (a) calculate corrected subclasses list, (b) correctly relate intersection and union classes with their collection classes, and (c) match union, intersection, sub-, complement, and equivalent classes in a proper sequence, to avoid error prone match results. We compare the results of our algorithms with those of a candidate reasoner, namely, the pellet reasoner. To the best of our knowledge, ours is a unique attempt in establishing a novel way to relate ontology classes. PMID:25984560

Gas-assisted gravity drainage (GAGD) process for improved oil recovery

DOEpatents

Rao, Dandina N [Baton Rouge, LA

2012-07-10

A rapid and inexpensive process for increasing the amount of hydrocarbons (e.g., oil) produced and the rate of production from subterranean hydrocarbon-bearing reservoirs by displacing oil downwards within the oil reservoir and into an oil recovery apparatus is disclosed. The process is referred to as "gas-assisted gravity drainage" and comprises the steps of placing one or more horizontal producer wells near the bottom of a payzone (i.e., rock in which oil and gas are found in exploitable quantities) of a subterranean hydrocarbon-bearing reservoir and injecting a fluid displacer (e.g., CO.sub.2) through one or more vertical wells or horizontal wells. Pre-existing vertical wells may be used to inject the fluid displacer into the reservoir. As the fluid displacer is injected into the top portion of the reservoir, it forms a gas zone, which displaces oil and water downward towards the horizontal producer well(s).

Synthetic mimicking of plant oils and comparison with naturally grown products in polyurethane synthesis.

PubMed

Coles, Stuart R; Barker, Guy; Clark, Andrew J; Kirwan, Kerry; Jacobs, Daniel; Makenji, Kylash; Pink, David

2008-06-11

The use of plant oils as industrial feedstocks can often be hampered by their lack of optimization towards a particular process, as well as their development being risky; growing suitable volumes of crops to test can take up to five years. To circumvent this, we aimed to discover a method that would mimic plant oil profiles in the laboratory, and show that they exhibited similar properties to the naturally grown plant oils in a given process. Using the synthesis of polyurethanes as an example, we have synthesized six different polymers and demonstrated that plant oils will produce polymers with similar physical properties to those oils mimicked in the laboratory. The use of this mimicking process can be extended to other types of polymers to obtain a method for predicting the properties of a given material based on the plant oil composition of a crop before it is grown in bulk.

40 CFR 80.1426 - How are RINs generated and assigned to batches of renewable fuel by renewable fuel producers or...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Fermentation using natural gas, biomass, or biogas for process energy 6 Biodiesel, and renewable diesel Soy... renewable biomass and petroleum 4 Biodiesel Canola oil Trans-Esterification using natural gas or biomass for process energy 4 Biodiesel, and renewable diesel Soy bean oil;Oil from annual covercrops; Algal oil...

40 CFR 80.1426 - How are RINs generated and assigned to batches of renewable fuel by renewable fuel producers or...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Fermentation using natural gas, biomass, or biogas for process energy 6 Biodiesel, and renewable diesel Soy... renewable biomass and petroleum 4 Biodiesel Canola oil Trans-Esterification using natural gas or biomass for process energy 4 Biodiesel, and renewable diesel Soy bean oil;Oil from annual covercrops; Algal oil...

Optimization of the degumming process for camellia oil by the use of phospholipase C in pilot-scale system.

PubMed

Jiang, Xiaofei; Chang, Ming; Jin, Qingzhe; Wang, Xingguo

2015-06-01

In present study, phospholipase C (PLC) was applied in camellia oil degumming and the response surface method (RSM) was used to determine the optimum degumming conditions (reaction time, reaction temperature and enzyme dosage) for this enzyme. The optimum conditions for the minimum residual phosphorus content (15.14 mg/kg) and maximum yield of camellia oil (98.2 %) were obtained at reaction temperature 53 ºC, reaction time 2.2 h, PLC dosage 400 mg/kg and pH 5.4. The application of phospholipase A (PLA) - assisted degumming process could further reduce the residual phosphorus content of camellia oil (6.84 mg/kg) to make the oil suitable for physical refining while maintaining the maximal oil yield (98.2 %). These results indicate that PLC degumming process in combination with PLA treatment can be a commercially viable alternative for traditional degumming process. Study on the quality changes of degummed oils showed that the oxidative stability of camellia oil was slightly deceased after the enzymatic treatment, thus more attention should be paid to the oxidative stability in the further application.

Influence of the processed sunflower oil on the cement properties

NASA Astrophysics Data System (ADS)

Fleysher, A. U.; Tokarchuk, V. V.; Sviderskiy, V. A.

2015-01-01

Used oils (vegetable oil, animal oil, engine oil, etc.), which are essentially industrial wastes, have found application as secondary raw materials in some braches of industry. In particular, the only well-known and commonly-used way of utilizing wastes of vegetable oils is to apply them as raw materials in the production of biodiesel. The goal of the present study is to develop a conceptually new way of vegetable oil wastes utilization in the building industry. The test admixture D-148 was obtained from the processing of wastes of sunflower oil and it mainly consists of fatty acid diethanolamide. The test admixture was added to the cement system for the purpose of studying its influence on water demand, flowability, setting times, compressive strength and moisture adsorption. The test admixture D-148 at the optimal content 0. 2 weight % causes 10% decrease in water demand, 1.7 time increase in flowability (namely spread diameter), 23% increase in grade strength and 34% decrease in moisture adsorption. The results of the present investigation make it possible to consider the final product of the waste sunflower oil processing as multifunctional plasticizing-waterproofing admixture.

Helping nature clean up oil spills

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paddock, A.

Oil spills are nothing new. In fact, for millions of years crude oil has been seeping up to the Earth`s surface, and for all that time Mother Nature has been on the job with microbes, or bacteria, to harmlessly convert the oil to water and carbon dioxide gas. Not all bacteria are bad. True, some can make us sick, however, the good ones help us bake bread, brew beer, and even clean up oil spills by a process known as biodegradation. Oil and bacteria don`t easily get together because oil and water don`t mix and bacteria prefer to stay inmore » water. After some oil tankers spills in the English Channel 25 years ago, major oil companies (Arco, BP, Exxon, and others) developed oil dispersant products-specialized chemicals that make oils and sea water mix. The simplest examples of similar wetting agents are soaps and detergents. Now, thanks to dispersants, the natural bacteria at sea can easily get to the oil and the normally slow biodegradation process goes rather quickly.« less

40 CFR 279.20 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Mixtures of used oil and diesel fuel mixed by the generator of the used oil for use in the generator's own... THE MANAGEMENT OF USED OIL Standards for Used Oil Generators § 279.20 Applicability. (a) General... oil generators. A used oil generator is any person, by site, whose act or process produces used oil or...

40 CFR 279.20 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Mixtures of used oil and diesel fuel mixed by the generator of the used oil for use in the generator's own... THE MANAGEMENT OF USED OIL Standards for Used Oil Generators § 279.20 Applicability. (a) General... oil generators. A used oil generator is any person, by site, whose act or process produces used oil or...

Comparison of different classification methods for analyzing electronic nose data to characterize sesame oils and blends.

PubMed

Shao, Xiaolong; Li, Hui; Wang, Nan; Zhang, Qiang

2015-10-21

An electronic nose (e-nose) was used to characterize sesame oils processed by three different methods (hot-pressed, cold-pressed, and refined), as well as blends of the sesame oils and soybean oil. Seven classification and prediction methods, namely PCA, LDA, PLS, KNN, SVM, LASSO and RF, were used to analyze the e-nose data. The classification accuracy and MAUC were employed to evaluate the performance of these methods. The results indicated that sesame oils processed with different methods resulted in different sensor responses, with cold-pressed sesame oil producing the strongest sensor signals, followed by the hot-pressed sesame oil. The blends of pressed sesame oils with refined sesame oil were more difficult to be distinguished than the blends of pressed sesame oils and refined soybean oil. LDA, KNN, and SVM outperformed the other classification methods in distinguishing sesame oil blends. KNN, LASSO, PLS, and SVM (with linear kernel), and RF models could adequately predict the adulteration level (% of added soybean oil) in the sesame oil blends. Among the prediction models, KNN with k = 1 and 2 yielded the best prediction results.

Citrus essential oils and their influence on the anaerobic digestion process: an overview.

PubMed

Ruiz, B; Flotats, X

2014-11-01

Citrus waste accounts for more than half of the whole fruit when processed for juice extraction. Among valorisation possibilities, anaerobic digestion for methane generation appears to be the most technically feasible and environmentally friendly alternative. However, citrus essential oils can inhibit this biological process. In this paper, the characteristics of citrus essential oils, as well as the mechanisms of their antimicrobial effects and potential adaptation mechanisms are reviewed. Previous studies of anaerobic digestion of citrus waste under different conditions are presented; however, some controversy exists regarding the limiting dosage of limonene for a stable process (24-192 mg of citrus essential oil per liter of digester and day). Successful strategies to avoid process inhibition by citrus essential oils are based either on recovery or removal of the limonene, by extraction or fungal pre-treatment respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of a hull-less pumpkin (Cucurbita pepo L.) seed oil press-cake spread.

PubMed

Radočaj, Olga; Dimić, Etelka; Vujasinović, Vesna

2012-09-01

A stable, oil-based spread rich in the omega-3 (ω-3) and omega-6 (ω-6) fatty acids was developed using a hull-less pumpkin seed (Cucurbita pepo L.) oil press-cake, a by-product of the pumpkin oil pressing process, along with cold-pressed hemp oil. Response surface methodology (RSM) was applied to investigate the effects of two factors, as the formulation's compositional variables: a commercial stabilizer (X(1) ) and cold-pressed hemp oil (X(2) ) added to the pumpkin seed oil press-cake in the spread formulations. A central composite, 2-factorial experimental design on 5 levels was used to optimize the spreads where model responses were ω-3 fatty acids content, spreadability (hardness), oil separation, and sensory evaluation. The selected responses were significantly affected by both variables (P < 0.05). The spreads resembled commercial peanut butter, both in appearance, texture and spreadability; were a source of ω-3 fatty acids and with no visual oil separation after 1 mo of storage. An optimum spread was produced using 1.25% (w/w) of stabilizer and 80% of hemp oil (w/w, of the total added oil) which had 0.97 g of ω-3 fatty acids per serving size; penetration depth of 68.4 mm; oil separation of 9.2% after 3 mo of storage; and a sensory score of 17.5. A use of by-products generated from different food processing technologies, where the edible waste is successfully incorporated as a value-added ingredient, has become a very important area of research to support global sustainability efforts. This study contributes to the knowledge of a product design process for oil-based spread development, where oil press-cake, a by-product of the oil pressing process of the naked pumpkin seeds, was used and where results have demonstrated that a new product can be successfully developed and potentially manufactured as a functional food. © 2012 Institute of Food Technologists®

Geometric parameters determination of the installation for oil-contaminated soils decontamination in Russia, the Siberian region and the Arctic zones climatic conditions with reagent encapsulating

NASA Astrophysics Data System (ADS)

Shtripling, L. O.; Kholkin, E. G.

2018-01-01

The article presents the procedure for determining the basic geometrical setting parameters for the oil-contaminated soils decontamination with reagent encapsulation method. An installation is considered for the operational elimination of the emergency consequences accompanied with oil spills, and the installation is adapted to winter conditions. In the installations exothermic process thermal energy of chemical neutralization of oil-contaminated soils released during the decontamination is used to thaw frozen subsequent portions of oil-contaminated soil. Installation for oil-contaminated soil decontamination as compared with other units has an important advantage, and it is, if necessary (e.g., in winter) in using the heat energy released at each decontamination process stage of oil-contaminated soil, in normal conditions the heat is dispersed into the environment. In addition, the short-term forced carbon dioxide delivery at the decontamination process final stage to a high concentration directly into the installation allows replacing the long process of microcapsule shells formation and hardening that occur in natural conditions in the open air.

Laboratory simulation studies of steady-state and potential catalytic effects in the ROPE{trademark} process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guffey, F.D.; Holper, P.A.

The Western Research Institute is currently developing a process for the recovery of distillable liquid products from alternate fossil fuel sources such as tar sand and oil shale. The processing concept is based on recycling a fraction of the produced oil back into the reactor with the raw resource. This concept is termed the recycle oil pyrolysis and extraction (ROPE{sup TM}) process. The conversion of the alternate resource to a liquid fuel is performed in two stages. The first recovery stage is performed at moderate temperatures (325--420{degrees}C [617--788{degrees}F]) in the presence of product oil recycle. The second stage is performedmore » at higher temperatures (450--540{degrees}C [842--1004{degrees}F]) in the absence of product oil. The experiments reported here were performed Asphalt Ridge tar sand in the all-glass laboratory simulation reactor to simulate (1) the recycling of SAE 50 weight oil in the recycle oil pyrolysis zone and (2) to evaluate the potential catalytic effects of the sand matrix.« less

Laboratory simulation studies of steady-state and potential catalytic effects in the ROPE trademark process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guffey, F.D.; Holper, P.A.

The Western Research Institute is currently developing a process for the recovery of distillable liquid products from alternate fossil fuel sources such as tar sand and oil shale. The processing concept is based on recycling a fraction of the produced oil back into the reactor with the raw resource. This concept is termed the recycle oil pyrolysis and extraction (ROPE{sup TM}) process. The conversion of the alternate resource to a liquid fuel is performed in two stages. The first recovery stage is performed at moderate temperatures (325--420{degrees}C (617--788{degrees}F)) in the presence of product oil recycle. The second stage is performedmore » at higher temperatures (450--540{degrees}C (842--1004{degrees}F)) in the absence of product oil. The experiments reported here were performed Asphalt Ridge tar sand in the all-glass laboratory simulation reactor to simulate (1) the recycling of SAE 50 weight oil in the recycle oil pyrolysis zone and (2) to evaluate the potential catalytic effects of the sand matrix.« less

Stem cell education for medical students at Tongji University: Primary cell culture and directional differentiation of rat bone marrow mesenchymal stem cells.

PubMed

Jin, Caixia; Tian, Haibin; Li, Jiao; Jia, Song; Li, Siguang; Xu, Guo-Tong; Xu, Lei; Lu, Lixia

2018-03-01

Stem cells are cells that can self-renew and differentiate into a variety of cell types under certain conditions. Stem cells have great potential in regenerative medicine and cell therapy for the treatment of certain diseases. To deliver knowledge about this frontier in science and technology to medical undergraduate students, we designed an innovative practical experiment for freshmen in their second semester. The lab exercise focused on rat bone marrow mesenchymal stem cell (BMSC) isolation, cell culture and differentiation, and it aimed to help students master the aseptic techniques for cell culture, the basic methods and procedures for the primary culture and passage of BMSCs, the basic procedure for the directional differentiation of BMSCs into adipocytes and their subsequent identification by oil-red-O staining. This lab exercise is a very meaningful and useful introduction to stem cell collection and manipulation and inspires medical students to deepen their understanding of translational medicine and regenerative medicine. © 2017 by The International Union of Biochemistry and Molecular Biology, 46(2):151-154, 2018. © 2017 The International Union of Biochemistry and Molecular Biology.

A model of oil-generation in a waterlogged and closed system

NASA Astrophysics Data System (ADS)

Zhigao, He

This paper presents a new model on synthetic effects on oil-generation in a waterlogged and closed system. It is suggested based on information about oil in high pressure layers (including gas dissolved in oil), marsh gas and its fermentative solution, fermentation processes and mechanisms, gaseous hydrocarbons of carbonate rocks by acid treatment, oil-field water, recent and ancient sediments, and simulation experiments of artificial marsh gas and biological action. The model differs completely from the theory of oil-generation by thermal degradation of kerogen but stresses the synthetic effects of oil-generation in special waterlogged and closed geological systems, the importance of pressure in oil-forming processes, and direct oil generation by micro-organisms. Oil generated directly by micro-organisms is a particular biochemical reaction. Another feature of this model is that generation, migration and accumulation of petroleum are considered as a whole.

[Some new phenomena of culturally legitimate examples of family formation].

PubMed

Mozny, I

1987-01-01

Recent changes in the process of family formation in Czechoslovakia are described. These include a reversal of the trends toward lower rates of illegitimacy and lower ages at marriage and increases in the number of divorces, the popularity of consensual unions, and the percent of marriages following pregnancy. Factors affecting consensual union are considered, including educational status, birth order, and marital status. (SUMMARY IN ENG AND RUS)

Hydroprocessing full-range of heavy oils and bitumen using ultradispersed catalysts at low severity

NASA Astrophysics Data System (ADS)

Peluso, Enzo

The progressive exhaustion of light crude oils is forcing the petroleum industry to explore new alternatives for the exploitation of unconventional oils. New approaches are searching for technologies able to produce, transport and refine these feedstocks at lower costs, in which symbiotic processes between the enhanced oil recovery (EOR) and the conventional upgrading technologies are under investigation. The process explored in this thesis is an interesting alternative for in-situ upgrading of these crude oils in the presence of ultradispersed (UD) catalysts, which are included as a disperse phase able to circulate along with the processed feed. The objectives of this work are: (a) study the performance of UD catalysts in the presence of a full range (non fractioned) heavy oil and bitumen and (b) evaluate the recyclability of the UD catalysts. Four different heavy crude oils were evaluated in the presence with UD catalysts at a total pressure of 2.8 MPa, residence time of 8 hours and reaction temperatures from 360 up to 400ºC. Thermal and catalytic hydro-processing were compared in terms of conversion and product stability. A comparison between the different crude oils was additionally derived in terms of SARA, initial micro-carbon content and virgin oil stability among other properties. Advantages of catalytic hydro-processing over thermal hydro-processing were evidenced, with UD catalysts playing an essential hydrogenating role while retarding coke formation; microcarbon and asphaltenes reduction in the presence of UD catalysts was observed. To evaluate the feasibility of recycling the UD catalysts, a micro-slurry recycled unit was developed as part of this research. These main results showed: (a) a successful design of this unit, (b) that temperature, LHSV and fractional recycling ratio have more impact on VGO conversion, while pressure has almost no effect, and (c) an UD catalysts agglomeration process was detected, however this process is slow and reversible.

Development of measures to improve technologies of energy recovery from gaseous wastes of oil shale processing

NASA Astrophysics Data System (ADS)

Tugov, A. N.; Ots, A.; Siirde, A.; Sidorkin, V. T.; Ryabov, G. A.

2016-06-01

Prospects of the use of oil shale are associated with its thermal processing for the production of liquid fuel, shale oil. Gaseous by-products, such as low-calorie generator gas with a calorific value up to 4.3MJ/m3 or semicoke gas with a calorific value up to 56.57 MJ/m3, are generated depending on the oil shale processing method. The main methods of energy recovery from these gases are either their cofiring with oil shale in power boilers or firing only under gaseous conditions in reconstructed or specially designed for this fuel boilers. The possible use of gaseous products of oil shale processing in gas-turbine or gas-piston units is also considered. Experiments on the cofiring of oil shale gas and its gaseous processing products have been carried out on boilers BKZ-75-39FSl in Kohtla-Järve and on the boiler TP-101 of the Estonian power plant. The test results have shown that, in the case of cofiring, the concentration of sulfur oxides in exhaust gases does not exceed the level of existing values in the case of oil shale firing. The low-temperature corrosion rate does not change as compared to the firing of only oil shale, and, therefore, operation conditions of boiler back-end surfaces do not worsen. When implementing measures to reduce the generation of NO x , especially of flue gas recirculation, it has been possible to reduce the emissions of nitrogen oxides in the whole boiler. The operation experience of the reconstructed boilers BKZ-75-39FSl after their transfer to the firing of only gaseous products of oil shale processing is summarized. Concentrations of nitrogen and sulfur oxides in the combustion products of semicoke and generator gases are measured. Technical solutions that made it possible to minimize the damage to air heater pipes associated with the low-temperature sulfur corrosion are proposed and implemented. The technological measures for burners of new boilers that made it possible to burn gaseous products of oil shale processing with low emissions of nitrogen oxides are developed.

Geophysical Investigations in the Caucasus (1925 - 2012): Initial, Basic and Modern Stages

NASA Astrophysics Data System (ADS)

Eppelbaum, L. V.

2012-04-01

The Caucasian Mountains occupy an area of about 440,000 km2. A number of important mineral resources are concentrated there. Geophysical data on the geological structure of Caucasus can shed light on the basic principles of evolution of the Earth, the distribution of minerals and seismic activity. However, geophysical surveys under complex conditions are generally riddled by poor accessibility to certain mountainous regions, the unevenness of observation surfaces, as well as by a great variety and frequent changes of tectonic structures and geological bodies with variable physical properties. These factors either restrict geophysical surveys in difficult environments or confine the scope of useful information drawn from the results obtained. This has led to the development of special techniques in geophysical surveys, data processing and interpretation that draws heavily on the experience accumulated in the specific conditions of these mountainous regions. First applied geophysical observations in the Caucasus region - thermal measurements in boreholes - were carried out by Bazevich (1881) in the Absheron Peninsula. At the same time, start of the initial stage is usually referred to as the mid 20-s of the XX century, when the rare, but systematic geophysical observations (mainly gravity and magnetic) were begun in some Caucasian areas. Somewhat later began to apply the resistivity method. Mid 30-s is characterized by the beginning of application of borehole geophysics and seismic prospecting. The marine seismics firstly in the former Soviet Union was tested in the Caspian Sea. In general, the initial stage is characterized by slow, but steady rise (except during World War II) lasted until 1960. A basic stage (1960-1991) is characterized by very intensive employment of geophysical methods (apparently, any possible geophysical methods were tested in this region). At this time the Caucasus region is considered in the former Soviet Union as a geophysical polygon for testing different geophysical methods and methodologies in complicated environments. Airborne magnetic and gravity surveys covered all the Caucasus, regional seismic and magnetotelluric studies were used as reference profiles for deep structure investigation. Numerous effective applications of geophysical methods for searching ore, oil&gas deposits, building raw, fresh water localization, solving engineering, etc. was demonstrated. Seismological investigations (including different methods) were widely applied throughout the entire Caucasian region. Satellite geophysical examinations were successfully combined with other methods. Finally, destruction of the former Soviet Union in 1991 (beginning of the modern stage) caused a sharp common decreasing of the geophysical activity in this region. Only foreign oil-&gas companies (mainly American and England) demonstrated some industrial geophysical activity basically in the Caspian Sea. In the last few years the situation began to straighten out, especially in the field of seismology. This presentation is based of the author's experience (e.g., Eppelbaum, 1989, 1991, 2009; Eppelbaum et al., 1987; Eppelbaum and Finkelstein, 1998; Eppelbaum and Khesin, 1988, 1992, 2002, 2004, 2011, 2012; Eppelbaum and Mishne, 2011; Eppelbaum et al., 2003, 2004; Khesin et al., 1988, 1993a, 1993b, 1996, 1997; Khesin and Eppelbaum, 1986, 1994, 1997, 2007; Pilchin and Eppelbaum, 1997, 2011) and corresponding publications and reviews of other authors.

A new submarine oil-water separation system

NASA Astrophysics Data System (ADS)

Cai, Wen-Bin; Liu, Bo-Hong

2017-12-01

In order to solve the oil field losses of environmental problems and economic benefit caused by the separation of lifting production liquid to offshore platforms in the current offshore oil production, from the most basic separation principle, a new oil-water separation system has been processed of adsorption and desorption on related materials, achieving high efficiency and separation of oil and water phases. And the submarine oil-water separation device has been designed. The main structure of the device consists of gas-solid phase separation device, period separating device and adsorption device that completed high efficiency separation of oil, gas and water under the adsorption and desorption principle, and the processing capacity of the device is calculated.

Polymeric nanospheres as a displacement fluid in enhanced oil recovery

NASA Astrophysics Data System (ADS)

Hendraningrat, Luky; Zhang, Julien

2015-12-01

This paper presents the investigation of using nanoscale polyacrylamide-based spheres (nanospheres) as a displacement fluid in enhanced oil recovery (EOR). Coreflood experiments were conducted to evaluate the impact of nanospheres and its concentration dispersed in model formation water on oil recovery during a tertiary oil recovery process. The coreflood results showed that nanospheres can enhance residual oil recovery in the sandstone rock samples and its concentration showed a significant impact into incremental oil. By evaluating the contact angle, it was observed that wettability alteration also might be involved in the possible oil displacement mechanism in this process together with fluid behavior and permeability to water that might divert injected fluid into unswept oil areas and enhance the residual oil recovery. These investigations promote nanospheres aqueous disperse solution as a potential displacement fluid in EOR.

17 CFR 210.4-10 - Financial accounting and reporting for oil and gas producing activities pursuant to the Federal...

Code of Federal Regulations, 2011 CFR

2011-04-01

... search for crude oil, including condensate and natural gas liquids, or natural gas (“oil and gas”) in...) Gathering, treating, and field processing (as in the case of processing gas to extract liquid hydrocarbons... first point at which oil, gas, or gas liquids, natural or synthetic, are delivered to a main pipeline, a...

Mathematical modelling of oil spill fate and transport in the marine environment incorporating biodegradation kinetics of oil droplets

NASA Astrophysics Data System (ADS)

Spanoudaki, Katerina

2016-04-01

Oil biodegradation by native bacteria is one of the most important natural processes that can attenuate the environmental impacts of marine oil spills. However, very few numerical models of oil spill fate and transport include biodegradation kinetics of spilled oil. Furthermore, in models where biodegradation is included amongst the oil transformation processes simulated, it is mostly represented as a first order decay process neglecting the effect of several important parameters that can limit biodegradation rate, such as oil composition and oil droplets-water interface. To this end, the open source numerical model MEDSKIL-II, which simulates oil spill fate and transport in the marine environment, has been modified to include biodegradation kinetics of oil droplets dispersed in the water column. MEDSLIK-II predicts the transport and weathering of oil spills following a Lagrangian approach for the solution of the advection-diffusion equation. Transport is governed by the 3D sea currents and wave field provided by ocean circulation models. In addition to advective and diffusive displacements, the model simulates several physical and chemical processes that transform the oil (evaporation, emulsification, dispersion in the water column, adhesion to coast). The fate algorithms employed in MEDSLIK-II consider the oil as a uniform substance whose properties change as the slick weathers, an approach that can lead to reduced accuracy, especially in the estimation of oil evaporation and biodegradation. Therefore MEDSLIK-II has been modified by adopting the "pseudo-component" approach for simulating weathering processes. Spilled oil is modelled as a relatively small number of discrete, non-interacting components (pseudo-components). Chemicals in the oil mixture are grouped by physical-chemical properties and the resulting pseudo-component behaves as if it were a single substance with characteristics typical of the chemical group. The fate (evaporation, dispersion, biodegradation) of each component is tracked separately. Biodegradation of oil droplets is modelled by Monod kinetics. The kinetics of oil particles size reduction due to the microbe-mediated degradation at water-oil particle interface is represented by the shrinking core model. In order to test the performance of the modified MEDSLIK-II model, it has been applied to a test case built-in the original code. The total fate of the oil spill is simulated both without biodegradation kinetics and when biodegradation is taken into account, for reasons of comparison. Several parameters that control biodegradation rate, including initial oil concentration and composition, size distribution of oil droplets and initial microbial concentration have been investigated. This upgraded version of MEDSLIK-II can be useful not only for predicting the transport and fate of spilled oil in the short term but also for evaluating different bioremediation strategies and risk assessment for the mid- and long term. Acknowledgements: The financial support by the EU project DECATASTROPHIZE: Use of SDSS and MCDA to Prepare for Disasters or Plan for Multiple Hazards, GA no. ECHO/SUB/2015/713788/PREP02, is greatly acknowledged.

Single-laboratory validation of a saponification method for the determination of four polycyclic aromatic hydrocarbons in edible oils by HPLC-fluorescence detection.

PubMed

Akdoğan, Abdullah; Buttinger, Gerhard; Wenzl, Thomas

2016-01-01

An analytical method is reported for the determination of four polycyclic aromatic hydrocarbons (benzo[a]pyrene (BaP), benz[a]anthracene (BaA), benzo[b]fluoranthene (BbF) and chrysene (CHR)) in edible oils (sesame, maize, sunflower and olive oil) by high-performance liquid chromatography. Sample preparation is based on three steps including saponification, liquid-liquid partitioning and, finally, clean-up by solid phase extraction on 2 g of silica. Guidance on single-laboratory validation of the proposed analysis method was taken from the second edition of the Eurachem guide on method validation. The lower level of the working range of the method was determined by the limits of quantification of the individual analytes, and the upper level was equal to 5.0 µg kg(-1). The limits of detection and quantification of the four PAHs ranged from 0.06 to 0.12 µg kg(-1) and from 0.13 to 0.24 µg kg(-1). Recoveries of more than 84.8% were achieved for all four PAHs at two concentration levels (2.5 and 5.0 µg kg(-1)), and expanded relative measurement uncertainties were below 20%. The performance of the validated method was in all aspects compliant with provisions set in European Union legislation for the performance of analytical methods employed in the official control of food. The applicability of the method to routine samples was evaluated based on a limited number of commercial edible oil samples.

Synthesis and analysis of jet fuel from shale oil and coal syncrudes

NASA Technical Reports Server (NTRS)

Gallagher, J. P.; Collins, T. A.; Nelson, T. J.; Pedersen, M. J.; Robison, M. G.; Wisinski, L. J.

1976-01-01

Thirty-two jet fuel samples of varying properties were produced from shale oil and coal syncrudes, and analyzed to assess their suitability for use. TOSCO II shale oil and H-COAL and COED syncrudes were used as starting materials. The processes used were among those commonly in use in petroleum processing-distillation, hydrogenation and catalytic hydrocracking. The processing conditions required to meet two levels of specifications regarding aromatic, hydrogen, sulfur and nitrogen contents at two yield levels were determined and found to be more demanding than normally required in petroleum processing. Analysis of the samples produced indicated that if the more stringent specifications of 13.5% hydrogen (min.) and 0.02% nitrogen (max.) were met, products similar in properties to conventional jet fuels were obtained. In general, shale oil was easier to process (catalyst deactivation was seen when processing coal syncrudes), consumed less hydrogen and yielded superior products. Based on these considerations, shale oil appears to be preferred to coal as a petroleum substitute for jet fuel production.

Hazardous Waste Minimization Assessment: Fort Campbell, Kentucky

DTIC Science & Technology

1991-03-01

Used Oii - Better Operating Practices . Selective Segregation 97 Used Oil - Process Change - Fast Lube Oil Change System (FLOCS) 98 Caustic Wastes...Product Substitution 98 Caustic Wastes - Process Change - Hot Tank (Equipment) Modifications 98 Aqueous or Caustic Wastes - Process Change - Dry Ovens...Aqueous or Caustic Wastes - Equipment Leasiag 102 Dirty Rags/Uniforms • Onsite/Offsite Recycling - Laundry Service 103 Treatment 103 Used Oil - Onsite

Process for tertiary oil recovery using tall oil pitch

DOEpatents

Radke, C.J.

1983-07-25

A process and compositions for enhancing the recovery of acid crudes are disclosed. The process involves injecting caustic solutions into the reservoir to maintain a pH of 11 to 13. The fluid contains an effective amount of multivalent cation for inhibiting alkaline silica dissolution with the reservoir. A tall oil pitch soap is added as a polymeric mobility control agent. (DMC)

On Boiling of Crude Oil under Elevated Pressure

NASA Astrophysics Data System (ADS)

Pimenova, Anastasiya V.; Goldobin, Denis S.

2016-02-01

We construct a thermodynamic model for theoretical calculation of the boiling process of multicomponent mixtures of hydrocarbons (e.g., crude oil). The model governs kinetics of the mixture composition in the course of the distillation process along with the boiling temperature increase. The model heavily relies on the theory of dilute solutions of gases in liquids. Importantly, our results are applicable for modelling the process under elevated pressure (while the empiric models for oil cracking are not scalable to the case of extreme pressure), such as in an oil field heated by lava intrusions.

Low-cost Solar Array Project. Feasibility of the Silane Process for Producing Semiconductor-grade Silicon

NASA Technical Reports Server (NTRS)

1979-01-01

The feasibility of Union Carbide's silane process for commercial application was established. An integrated process design for an experimental process system development unit and a commercial facility were developed. The corresponding commercial plant economic performance was then estimated.

Test of the cosmic evolution using Gaussian processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Ming-Jian; Xia, Jun-Qing, E-mail: zhangmj@ihep.ac.cn, E-mail: xiajq@bnu.edu.cn

2016-12-01

Much focus was on the possible slowing down of cosmic acceleration under the dark energy parametrization. In the present paper, we investigate this subject using the Gaussian processes (GP), without resorting to a particular template of dark energy. The reconstruction is carried out by abundant data including luminosity distance from Union2, Union2.1 compilation and gamma-ray burst, and dynamical Hubble parameter. It suggests that slowing down of cosmic acceleration cannot be presented within 95% C.L., in considering the influence of spatial curvature and Hubble constant. In order to reveal the reason of tension between our reconstruction and previous parametrization constraint formore » Union2 data, we compare them and find that slowing down of acceleration in some parametrization is only a ''mirage'. Although these parameterizations fits well with the observational data, their tension can be revealed by high order derivative of distance D. Instead, GP method is able to faithfully model the cosmic expansion history.« less

The local impact of globalization: worker health and safety in Mexico's sugar industry.

PubMed

Lemus-Ruiz, B E

1999-01-01

With the opening of its economy to international trade, the government of Mexico privatized many of its productive holdings, including the state-owned sugar industry. Sugar cane and mill workers had played an important role in the armed struggles of the revolutionary period (1910-1917). Organized into a militant labor union, they had become staunch supporters of the new government in the following decades. Furthermore, in the early years of industrialization, the sugar industry was very important for the Mexican economy, and the union played an active role in the political arena. Since the privatization of the sugar mills, the sugar workers have experienced a dramatic reorganization of the work process, and industry-union relationships are being reshaped. This paper offers an analysis of the impact of the privatization on workers' health and safety. Since the economic and social changes in the work process have a direct impact on the community as a whole, the study also explores these effects.

A superhydrophobic copper mesh as an advanced platform for oil-water separation

NASA Astrophysics Data System (ADS)

Ren, Guina; Song, Yuanming; Li, Xiangming; Zhou, Yanli; Zhang, Zhaozhu; Zhu, Xiaotao

2018-01-01

Improving the separation efficiency and simplifying the separation process would be highly desired for oil-water separation yet still challenging. Herein, to address this challenge, we fabricated a superhydrophobic copper mesh by an immersion process and exploited it as an advanced platform for oil-water separation. To realize oil-water separation efficiently, the obtained mesh was enfolded directly to form a boat-like device, and it could also be mounted on an open end of a glass barrel to form the oil skimmer device. For these devices, they can collect the floating oils through the pores of the copper mesh while repelling water completely, and the oil collection efficiency is up to 99.5%. Oils collected in the devices can be easily sucked out into a container for storing, without requiring mechanical handing for recycling. Importantly, the miniature boat and the oil skimmer devices can retain their enhanced oil collection efficiency even after 10 cycles of oil-water separation. Moreover, exploiting its superhydrophobicity under oil, the obtained copper mesh was demonstrated as a novel platform to remove tiny water droplets from oil.

40 CFR 279.11 - Used oil specifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Used oil specifications. 279.11... (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Applicability § 279.11 Used oil specifications. Used oil burned for energy recovery, and any fuel produced from used oil by processing, blending, or other...

40 CFR 279.11 - Used oil specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Used oil specifications. 279.11... (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Applicability § 279.11 Used oil specifications. Used oil burned for energy recovery, and any fuel produced from used oil by processing, blending, or other...

40 CFR 279.11 - Used oil specifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Used oil specifications. 279.11... (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Applicability § 279.11 Used oil specifications. Used oil burned for energy recovery, and any fuel produced from used oil by processing, blending, or other...

40 CFR 279.11 - Used oil specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Used oil specifications. 279.11... (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Applicability § 279.11 Used oil specifications. Used oil burned for energy recovery, and any fuel produced from used oil by processing, blending, or other...

43 CFR 3935.10 - Accounting records.

Code of Federal Regulations, 2012 CFR

2012-10-01

... processing plant and retort; (3) Mineral products produced and sold; (4) Shale oil products, shale gas, and... mined or processed and of all products including synthetic petroleum, shale oil, shale gas, and shale..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE EXPLORATION AND LEASES...

43 CFR 3935.10 - Accounting records.

Code of Federal Regulations, 2014 CFR

2014-10-01

... processing plant and retort; (3) Mineral products produced and sold; (4) Shale oil products, shale gas, and... mined or processed and of all products including synthetic petroleum, shale oil, shale gas, and shale..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE EXPLORATION AND LEASES...

43 CFR 3935.10 - Accounting records.

Code of Federal Regulations, 2013 CFR

2013-10-01

... processing plant and retort; (3) Mineral products produced and sold; (4) Shale oil products, shale gas, and... mined or processed and of all products including synthetic petroleum, shale oil, shale gas, and shale..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE EXPLORATION AND LEASES...

Bio-oil from fast pyrolysis of lignin: Effects of process and upgrading parameters.

PubMed

Fan, Liangliang; Zhang, Yaning; Liu, Shiyu; Zhou, Nan; Chen, Paul; Cheng, Yanling; Addy, Min; Lu, Qian; Omar, Muhammad Mubashar; Liu, Yuhuan; Wang, Yunpu; Dai, Leilei; Anderson, Erik; Peng, Peng; Lei, Hanwu; Ruan, Roger

2017-10-01

Effects of process parameters on the yield and chemical profile of bio-oil from fast pyrolysis of lignin and the processes for lignin-derived bio-oil upgrading were reviewed. Various process parameters including pyrolysis temperature, reactor types, lignin characteristics, residence time, and feeding rate were discussed and the optimal parameter conditions for improved bio-oil yield and quality were concluded. In terms of lignin-derived bio-oil upgrading, three routes including pretreatment of lignin, catalytic upgrading, and co-pyrolysis of hydrogen-rich materials have been investigated. Zeolite cracking and hydrodeoxygenation (HDO) treatment are two main methods for catalytic upgrading of lignin-derived bio-oil. Factors affecting zeolite activity and the main zeolite catalytic mechanisms for lignin conversion were analyzed. Noble metal-based catalysts and metal sulfide catalysts are normally used as the HDO catalysts and the conversion mechanisms associated with a series of reactions have been proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Catalytic hydroprocessing of heavy oil feedstocks

NASA Astrophysics Data System (ADS)

Okunev, A. G.; Parkhomchuk, E. V.; Lysikov, A. I.; Parunin, P. D.; Semeikina, V. S.; Parmon, V. N.

2015-09-01

A grave problem of modern oil refining industry is continuous deterioration of the produced oil quality, on the one hand, and increase in the demand for motor fuels, on the other hand. This necessitates processing of heavy oil feedstock with high contents of sulfur, nitrogen and metals and the atmospheric residue. This feedstock is converted to light oil products via hydrogenation processes catalyzed by transition metal compounds, first of all, cobalt- or nickel-promoted molybdenum and tungsten compounds. The processing involves desulfurization, denitrogenation and demetallization reactions as well as reactions converting heavy hydrocarbons to lighter fuel components. The review discusses the mechanisms of reactions involved in the heavy feedstock hydroprocessing, the presumed structure and state of the catalytically active components and methods for the formation of supports with the desired texture. Practically used and prospective approaches to catalytic upgrading of heavy oil feedstock as well as examples of industrial processing of bitumen and vacuum residues in the presence of catalysts are briefly discussed. The bibliography includes 140 references.

Technical difficulties and solutions of direct transesterification process of microbial oil for biodiesel synthesis.

PubMed

Yousuf, Abu; Khan, Maksudur Rahman; Islam, M Amirul; Wahid, Zularisam Ab; Pirozzi, Domenico

2017-01-01

Microbial oils are considered as alternative to vegetable oils or animal fats as biodiesel feedstock. Microalgae and oleaginous yeast are the main candidates of microbial oil producers' community. However, biodiesel synthesis from these sources is associated with high cost and process complexity. The traditional transesterification method includes several steps such as biomass drying, cell disruption, oil extraction and solvent recovery. Therefore, direct transesterification or in situ transesterification, which combines all the steps in a single reactor, has been suggested to make the process cost effective. Nevertheless, the process is not applicable for large-scale biodiesel production having some difficulties such as high water content of biomass that makes the reaction rate slower and hurdles of cell disruption makes the efficiency of oil extraction lower. Additionally, it requires high heating energy in the solvent extraction and recovery stage. To resolve these difficulties, this review suggests the application of antimicrobial peptides and high electric fields to foster the microbial cell wall disruption.

Innovative method for recovery and valorization of hydroxytyrosol from olive mill wastewaters.

PubMed

Bonetti, A; Venturini, S; Ena, A; Faraloni, C

2016-01-01

The nutritional properties of olive oil can be attributed to its oleic acid and phenolic compounds content, acting as natural oxidants to prevent human diseases. In particular, hydroxytyrosol has an anti-inflammatory action similar to omega 3 fatty acids from fish oil. The olive oil production was conducted by two extraction procedures: first, a two-phase extraction giving extra-virgin olive oil and humid pomace, second, a three-phase working process of humid pomace, obtaining another minimum quantity of extra-virgin olive oil, 'dry' pomace devoid of polyphenols, and mill wastewaters rich in anti-oxidant compounds. The aim of this processing was to employ water to extract the highest concentration of polyphenols from humid pomace and convey them in oil mill wastewaters for extraction. Processed olives were 37,200 kg, pomace deprived of polyphenols was equal to 20,400 kg and processing was performed with 500 kg of olives per hour. This method offers advantages of using cheap equipment and technical simplicity.

Effects of Microwave Radiation on Oil Recovery

NASA Astrophysics Data System (ADS)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Multifunctional two-stage riser fluid catalytic cracking process.

PubMed

Zhang, Jinhong; Shan, Honghong; Chen, Xiaobo; Li, Chunyi; Yang, Chaohe

This paper described the discovering process of some shortcomings of the conventional fluid catalytic cracking (FCC) process and the proposed two-stage riser (TSR) FCC process for decreasing dry gas and coke yields and increasing light oil yield, which has been successfully applied in 12 industrial units. Furthermore, the multifunctional two-stage riser (MFT) FCC process proposed on the basis of the TSR FCC process was described, which were carried out by the optimization of reaction conditions for fresh feedstock and cycle oil catalytic cracking, respectively, by the coupling of cycle oil cracking and light FCC naphtha upgrading processes in the second-stage riser, and the specially designed reactor for further reducing the olefin content of gasoline. The pilot test showed that it can further improve the product quality, increase the diesel yield, and enhance the conversion of heavy oil.

Manipulating surface wettability and oil absorbency of diatomite depending on processing and ambient conditions

NASA Astrophysics Data System (ADS)

Özen, İlhan; Şimşek, Süleyman; Okyay, Gamze

2015-03-01

In this study, a diatomite sample, which is a natural inorganic mineral with inherently high water and oil absorption capacity, was subjected to grinding before surface modification. Afterwards, the diatomite surface was modified via facile methods using a fluorocarbon (FC) chemical and stearic acid (SA) in addition to the sol-gel fluorosilanization (FS) process. The water and oil wettability, and oil absorbency properties of the unmodified and modified diatomites were investigated in addition to diatomite characterizations such as chemical content, surface area, particle size distribution, morphology, and modification efficiency. It was revealed that the wettability was changed completely depending on the surface modification agent and the media used, while the oil absorbency property surprisingly did not change. On the other hand, the oil absorbency was worsened by the grinding process, whereas the wettability was not affected.

Developments and challenges in biodiesel production from microalgae: A review.

PubMed

Taparia, Tanvi; Mvss, Manjari; Mehrotra, Rajesh; Shukla, Paritosh; Mehrotra, Sandhya

2016-09-01

The imminent depletion of fossil fuels and the surging global demand for renewable energy have led to the search for nonconventional energy sources. After a few decades of trial and error, the world is now testing the sources of the third generation of fossil fuels, which contain for most parts microalgae. With more than 80% oil content, being adaptable in growth parameters and highly versatile, microalgae are highly promising sources of biofuels in the present time. The present article makes a sweeping attempt to highlight the various methods employed for cultivation of microalgae, techniques to harvest and extract biomass from huge algal cultures, as well as their downstream production and processing procedures. The advantages, limitations, and challenges faced by each of them have been described to some extent. Major concerns pertaining to biofuels are supposed to be their environmental sustainability and economic viability along with their cost effectiveness. This would require a great deal of empirical data on existing systems and a great deal of optimization to generate a more robust one. We have concluded our article with a SWOT analysis of using algae for biodiesel production in a tabulated form. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

Converting oil shale to liquid fuels: energy inputs and greenhouse gas emissions of the Shell in situ conversion process.

PubMed

Brandt, Adam R

2008-10-01

Oil shale is a sedimentary rock that contains kerogen, a fossil organic material. Kerogen can be heated to produce oil and gas (retorted). This has traditionally been a CO2-intensive process. In this paper, the Shell in situ conversion process (ICP), which is a novel method of retorting oil shale in place, is analyzed. The ICP utilizes electricity to heat the underground shale over a period of 2 years. Hydrocarbons are produced using conventional oil production techniques, leaving shale oil coke within the formation. The energy inputs and outputs from the ICP, as applied to oil shales of the Green River formation, are modeled. Using these energy inputs, the greenhouse gas (GHG) emissions from the ICP are calculated and are compared to emissions from conventional petroleum. Energy outputs (as refined liquid fuel) are 1.2-1.6 times greater than the total primary energy inputs to the process. In the absence of capturing CO2 generated from electricity produced to fuel the process, well-to-pump GHG emissions are in the range of 30.6-37.1 grams of carbon equivalent per megajoule of liquid fuel produced. These full-fuel-cycle emissions are 21%-47% larger than those from conventionally produced petroleum-based fuels.

Environmental hazards of automobile mechanics in Ibadan, Nigeria.

PubMed

Omokhodion, F O

1999-01-01

A cross sectional survey was conducted among automobile mechanics and technicians in Ibadan to determine the socio-demographic characteristics and environmental hazards of these workers. Three hundred workers were interviewed. All respondents were males aged between 13 and 72 years of age. Educational attainment was poor, with only 20% of respondents having completed secondary education. Sanitation facilities were inadequate. Forty percent of workshops provided facilities for refuse disposal. Of the 33 workshops visited, only 1 provided toilet facilities. Most workers used facilities in neighbouring residential premises. Only three workshops (9%) had designated eating areas. Occupational exposure to petrol was common to all trades. Other occupational exposures were to petrochemicals such as engine oil and brake oil. Protective clothing was not used by the majority of workers. Only 25 (8%) respondents were wearing overalls at the time of our visit. This findings illustrate the typical work conditions of workers in small scale industries. There is a need for health education programmes about occupational and non-occupational diseases. This and other health promotion activities can be organized through the unions.

Breaking the Biological Barriers to Cellulosic Ethanol: A Joint Research Agenda. A Research Roadmap Resulting from the Biomass to Biofuels Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2006-06-30

A robust fusion of the agricultural, industrial biotechnology, and energy industries can create a new strategic national capability for energy independence and climate protection. In his State of the Union Address (*Bush 2006), President George W. Bush outlined the Advanced Energy Initiative, which seeks to reduce our national dependence on imported oil by accelerating the development of domestic,renewable alternatives to gasoline and diesel fuels. The president has set a national goal of developing cleaner, cheaper, and more reliable alternative energy sources to substantially replace oil imports in the coming years.Fuels derived from cellulosic biomass—the fibrous, woody, and generally inedible portionsmore » of plant matter—offer one such alternative to conventional energy sources that can dramatically impact national economic growth, national energy security, and environmental goals. Cellulosic biomass is an attractive energy feedstock because it is an abundant, domestic, renewable source that can be converted to liquid transportation fuels.These fuels can be used readily by current-generation vehicles and distributed through the existing transportation-fuel infrastructure.« less

Analysis of 16 phthalic acid esters in food simulants from plastic food contact materials by LC-ESI-MS/MS.

PubMed

Li, Xiaojing; Xiong, Wenming; Lin, Hua; Zhuo, Liyang; Lv, Shuiyuan; Tang, Xi; Chen, Minshi; Zou, Zhexiang; Lin, Zhenyu; Qiu, Bin; Chen, Guonan

2013-02-01

An RP LC-ESI-MS/MS method for the determination of the migration of 16 primary phthalic acid esters from plastic samples has been developed using distilled water, 3% acetic acid, 10% alcohol, and olive oil as food simulants. Detection limits were 1.6-18.5 μg/kg in distilled water, 1.4-17.3 μg/kg in 3% acetic acid, 1.4-19.2 μg/kg in 10% alcohol, and 31.9-390.8 μg/kg in olive oil. The RSDs were in the range of 0.07-11.28%. The real plastic products inspection showed that only few analyzed samples were phthalates contaminated. Bis-2-ethylhexyl ester and dibutyl phthalate were the common items migrated from the plastic products into food and feeds, but the migration concentrations were far below the limits set by European Union (1.5 mg/kg for bis-2-ethylhexyl ester and 0.3 mg/kg for dibutyl phthalate). © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Jet fuels from synthetic crudes

NASA Technical Reports Server (NTRS)

Antoine, A. C.; Gallagher, J. P.

1977-01-01

An investigation was conducted to determine the technical problems in the conversion of a significant portion of a barrel of either a shale oil or a coal synthetic crude oil into a suitable aviation turbine fuel. Three syncrudes were used, one from shale and two from coal, chosen as representative of typical crudes from future commercial production. The material was used to produce jet fuels of varying specifications by distillation, hydrotreating, and hydrocracking. Attention is given to process requirements, hydrotreating process conditions, the methods used to analyze the final products, the conditions for shale oil processing, and the coal liquid processing conditions. The results of the investigation show that jet fuels of defined specifications can be made from oil shale and coal syncrudes using readily available commercial processes.

40 CFR 419.50 - Applicability; description of the integrated subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... topping, cracking, lube oil manufacturing processes, and petrochemical operations, whether or not the facility includes any process in addition to topping, cracking, lube oil manufacturing processes, and...

40 CFR 419.50 - Applicability; description of the integrated subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... topping, cracking, lube oil manufacturing processes, and petrochemical operations, whether or not the facility includes any process in addition to topping, cracking, lube oil manufacturing processes, and...

43 CFR 3922.10 - Application processing fee.

Code of Federal Regulations, 2012 CFR

2012-10-01

... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) OIL SHALE LEASING Application Processing... process for a competitive oil shale lease is as follows: (1) The applicant nominating the tract for...

43 CFR 3922.10 - Application processing fee.

Code of Federal Regulations, 2011 CFR

2011-10-01

... MANAGEMENT, DEPARTMENT OF THE INTERIOR RANGE MANAGEMENT (4000) OIL SHALE LEASING Application Processing... process for a competitive oil shale lease is as follows: (1) The applicant nominating the tract for...

43 CFR 3922.10 - Application processing fee.

Code of Federal Regulations, 2014 CFR

2014-10-01

... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) OIL SHALE LEASING Application Processing... process for a competitive oil shale lease is as follows: (1) The applicant nominating the tract for...

43 CFR 3922.10 - Application processing fee.

Code of Federal Regulations, 2013 CFR

2013-10-01

... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) OIL SHALE LEASING Application Processing... process for a competitive oil shale lease is as follows: (1) The applicant nominating the tract for...

Re-refining of waste petroleum by competing solubility characteristics

NASA Astrophysics Data System (ADS)

Byars, Michael Steven

1998-11-01

The United States produces over 1.3 billion gallons of used oil per year. Of the 1.3 billion gallons about 60% is used as fuel, nearly 20% is dumped into the environment, 13% is placed in landfills, 2% is re-refined into lube oil, and the remaining is either used for other purposes or incinerated. This is a great potential source of lubricating oil. The work presented here is a solvent extraction process using a solvent (highly miscible with the oil) and a co-solvent (slightly miscible with the oil). Extractions using isopropanol, ethanol, methyl tert-butylether and methanol are presented. The criteria used for evaluation of the extraction processes are yield, product viscosity index, and ash percent. The solvent/co-solvent combinations of MTBE and ethanol performed best and had the advantage of a common solvent/co-solvent in all extraction steps. The extraction process that provided the best results was a two step process using a combination solvent of MTBE and ethanol. The used oil was first extracted using MTBE/ethanol. The extracted oil was then contacted with a solvent combination composed of 80% ethanol. This solvent combination extracted the remaining additives from the oil. The recovered oil was nearly 60% by weight with a high viscosity index and no ash content. A preliminary battery limits design and economic analysis of the process was performed. A 500 bbl/day plant would have a capital cost of 1.9 million and an annual operation cost of 310,000. The plant as designed would produce 300 bbl/day of lube feedstock and have an ROI of 19%.

Online sensing and control of oil in process wastewater

NASA Astrophysics Data System (ADS)

Khomchenko, Irina B.; Soukhomlinoff, Alexander D.; Mitchell, T. F.; Selenow, Alexander E.

2002-02-01

Industrial processes, which eliminate high concentration of oil in their waste stream, find it extremely difficult to measure and control the water purification process. Most oil separation processes involve chemical separation using highly corrosive caustics, acids, surfactants, and emulsifiers. Included in the output of this chemical treatment process are highly adhesive tar-like globules, emulsified and surface oils, and other emulsified chemicals, in addition to suspended solids. The level of oil/hydrocarbons concentration in the wastewater process may fluctuate from 1 ppm to 10,000 ppm, depending upon the specifications of the industry and level of water quality control. The authors have developed a sensing technology, which provides the accuracy of scatter/absorption sensing in a contactless environment by combining these methodologies with reflective measurement. The sensitivity of the sensor may be modified by changing the fluid level control in the flow cell, allowing for a broad range of accurate measurement from 1 ppm to 10,000 ppm. Because this sensing system has been designed to work in a highly invasive environment, it can be placed close to the process source to allow for accurate real time measurement and control.

Effect of processing conditions on oil point pressure of moringa oleifera seed.

PubMed

Aviara, N A; Musa, W B; Owolarafe, O K; Ogunsina, B S; Oluwole, F A

2015-07-01

Seed oil expression is an important economic venture in rural Nigeria. The traditional techniques of carrying out the operation is not only energy sapping and time consuming but also wasteful. In order to reduce the tedium involved in the expression of oil from moringa oleifera seed and develop efficient equipment for carrying out the operation, the oil point pressure of the seed was determined under different processing conditions using a laboratory press. The processing conditions employed were moisture content (4.78, 6.00, 8.00 and 10.00 % wet basis), heating temperature (50, 70, 85 and 100 °C) and heating time (15, 20, 25 and 30 min). Results showed that the oil point pressure increased with increase in seed moisture content, but decreased with increase in heating temperature and heating time within the above ranges. Highest oil point pressure value of 1.1239 MPa was obtained at the processing conditions of 10.00 % moisture content, 50 °C heating temperature and 15 min heating time. The lowest oil point pressure obtained was 0.3164 MPa and it occurred at the moisture content of 4.78 %, heating temperature of 100 °C and heating time of 30 min. Analysis of Variance (ANOVA) showed that all the processing variables and their interactions had significant effect on the oil point pressure of moringa oleifera seed at 1 % level of significance. This was further demonstrated using Response Surface Methodology (RSM). Tukey's test and Duncan's Multiple Range Analysis successfully separated the means and a multiple regression equation was used to express the relationship existing between the oil point pressure of moringa oleifera seed and its moisture content, processing temperature, heating time and their interactions. The model yielded coefficients that enabled the oil point pressure of the seed to be predicted with very high coefficient of determination.

The European Arctic policy in progress

NASA Astrophysics Data System (ADS)

Conde Pérez, Elena; Yaneva, Zhaklin Valerieva

2016-09-01

The geostrategic, political, economic, and scientific relevance of the Arctic is constantly growing due to the complex process of climate change. Accordingly, the European Union-as a global political actor-, is already taking steps to ensure and strengthen its influence in the region while demonstrating readiness to face the many opportunities and challenges ahead in cooperation with the traditional stakeholders. Therefore, in order to reflect the renewed importance of the Arctic transformation, the Union has been designing its Arctic Policy focusing on climate change mitigation and multilateral cooperation as its main strengths. Unfortunately, despite the diligence and impetus that has been invested, this process has been delayed in several occasions as the Union had to deal with internal and external destabilizing factors, such as the later immigration crisis or the lack of uniformity among its member states' foreign policy interests. These factors will be analyzed along with the process of creation and development of the EU's Arctic policy. Despite some delays, on 27 April 2016, the long-awaited third communication was issued and progress has been made: even if, in general terms, the new document remains a political statement, there is also a clear commitment to action.

Mechanism of oil-pulling therapy - in vitro study.

PubMed

Asokan, Sharath; Rathinasamy, T K; Inbamani, N; Menon, Thangam; Kumar, S Senthil; Emmadi, Pamela; Raghuraman, R

2011-01-01

Oil pulling has been used extensively as a traditional Indian folk remedy without scientific proof for many years for strengthening teeth, gums and jaws and to prevent decay, oral malodor, bleeding gums and dryness of throat and cracked lips. The aim of this study was to evaluate the antibacterial activity of sesame oil and lignans isolated from sesame oil on oral microorganisms and to check whether saponification or emulsification occurs during oil-pulling therapy. The in vitro study was carried out in three different phases: (1) Antibacterial activity of the lignans and sesame oil were tested by minimum inhibitory concentration assay by agar dilution method and agar well diffusion method, respectively. (2) Increase in free fatty acid level of oil and the quantity of sodium hydroxide (NaOH) used up in the titration are good indicators of saponification process. This was assessed using analytical tests for vegetable oils. (3) Swished oil was observed under light microscope to assess the status of the oil, presence of microorganisms, oral debris and foreign bodies. Sesamin and sesamolin isolated from sesame oil did not have any antibacterial effect against oral microorganisms like Streptococcus mutans, Streptococcus mitis and Streptococcus viridans. Emulsification of sesame oil occurs during oil-pulling therapy. Increased consumption of NaOH in titration is a definite indication of a possible saponification process. The myth that the effect of oil-pulling therapy on oral health was just a placebo effect has been broken and there are clear indications of possible saponification and emulsification process, which enhances its mechanical cleaning action.

The oil pressure test of the hydraulic impeller blade

NASA Astrophysics Data System (ADS)

Ye, Wen-bo; Jia, Li-tao

2017-12-01

This article introduced the structure of the Kaplan runner in hydropower station and the operating process of the oil pressure test has been described. What’s more, the whole process, including filling oil to the runner hub, the movement of the runner blade, the oil circuit, have been presented in detail.Since the manipulation of the oil circuit which controlled by three Valve groups consisting of six valves was complicated, the author is planning to replace them with 3-position 3-way electromagnetic valves, so we can simplify the operation procedure.The author hopes this article can provide technical reference for the oil pressure test.

43 CFR 3935.10 - Accounting records.

Code of Federal Regulations, 2011 CFR

2011-10-01

... processing plant and retort; (3) Mineral products produced and sold; (4) Shale oil products, shale gas, and... mined or processed and of all products including synthetic petroleum, shale oil, shale gas, and shale..., DEPARTMENT OF THE INTERIOR RANGE MANAGEMENT (4000) MANAGEMENT OF OIL SHALE EXPLORATION AND LEASES Production...

Liquid fuels from food waste: An alternative process to co-digestion

NASA Astrophysics Data System (ADS)

Sim, Yoke-Leng; Ch'ng, Boon-Juok; Mok, Yau-Cheng; Goh, Sok-Yee; Hilaire, Dickens Saint; Pinnock, Travis; Adams, Shemlyn; Cassis, Islande; Ibrahim, Zainab; Johnson, Camille; Johnson, Chantel; Khatim, Fatima; McCormack, Andrece; Okotiuero, Mary; Owens, Charity; Place, Meoak; Remy, Cristine; Strothers, Joel; Waithe, Shannon; Blaszczak-Boxe, Christopher; Pratt, Lawrence M.

2017-04-01

Waste from uneaten, spoiled, or otherwise unusable food is an untapped source of material for biofuels. A process is described to recover the oil from mixed food waste, together with a solid residue. This process includes grinding the food waste to an aqueous slurry, skimming off the oil, a combined steam treatment of the remaining solids concurrent with extrusion through a porous cylinder to release the remaining oil, a second oil skimming step, and centrifuging the solids to obtain a moist solid cake for fermentation. The water, together with any resulting oil from the centrifuging step, is recycled back to the grinding step, and the cycle is repeated. The efficiency of oil extraction increases with the oil content of the waste, and greater than 90% of the oil was collected from waste containing at least 3% oil based on the wet mass. Fermentation was performed on the solid cake to obtain ethanol, and the dried solid fermentation residue was a nearly odorless material with potential uses of biochar, gasification, or compost production. This technology has the potential to enable large producers of food waste to comply with new laws which require this material to be diverted from landfills.

An Exogenous Surfactant-Producing Bacillus subtilis Facilitates Indigenous Microbial Enhanced Oil Recovery

PubMed Central

Gao, Peike; Li, Guoqiang; Li, Yanshu; Li, Yan; Tian, Huimei; Wang, Yansen; Zhou, Jiefang; Ma, Ting

2016-01-01

This study used an exogenous lipopeptide-producing Bacillus subtilis to strengthen the indigenous microbial enhanced oil recovery (IMEOR) process in a water-flooded reservoir in the laboratory. The microbial processes and driving mechanisms were investigated in terms of the changes in oil properties and the interplay between the exogenous B. subtilis and indigenous microbial populations. The exogenous B. subtilis is a lipopeptide producer, with a short growth cycle and no oil-degrading ability. The B. subtilis facilitates the IMEOR process through improving oil emulsification and accelerating microbial growth with oil as the carbon source. Microbial community studies using quantitative PCR and high-throughput sequencing revealed that the exogenous B. subtilis could live together with reservoir microbial populations, and did not exert an observable inhibitory effect on the indigenous microbial populations during nutrient stimulation. Core-flooding tests showed that the combined exogenous and indigenous microbial flooding increased oil displacement efficiency by 16.71%, compared with 7.59% in the control where only nutrients were added, demonstrating the application potential in enhanced oil recovery in water-flooded reservoirs, in particular, for reservoirs where IMEOR treatment cannot effectively improve oil recovery. PMID:26925051

An Exogenous Surfactant-Producing Bacillus subtilis Facilitates Indigenous Microbial Enhanced Oil Recovery.

PubMed

Gao, Peike; Li, Guoqiang; Li, Yanshu; Li, Yan; Tian, Huimei; Wang, Yansen; Zhou, Jiefang; Ma, Ting

2016-01-01

This study used an exogenous lipopeptide-producing Bacillus subtilis to strengthen the indigenous microbial enhanced oil recovery (IMEOR) process in a water-flooded reservoir in the laboratory. The microbial processes and driving mechanisms were investigated in terms of the changes in oil properties and the interplay between the exogenous B. subtilis and indigenous microbial populations. The exogenous B. subtilis is a lipopeptide producer, with a short growth cycle and no oil-degrading ability. The B. subtilis facilitates the IMEOR process through improving oil emulsification and accelerating microbial growth with oil as the carbon source. Microbial community studies using quantitative PCR and high-throughput sequencing revealed that the exogenous B. subtilis could live together with reservoir microbial populations, and did not exert an observable inhibitory effect on the indigenous microbial populations during nutrient stimulation. Core-flooding tests showed that the combined exogenous and indigenous microbial flooding increased oil displacement efficiency by 16.71%, compared with 7.59% in the control where only nutrients were added, demonstrating the application potential in enhanced oil recovery in water-flooded reservoirs, in particular, for reservoirs where IMEOR treatment cannot effectively improve oil recovery.

Electrocoagulation with polarity switch for fast oil removal from oil in water emulsions.

PubMed

Gobbi, Lorena C A; Nascimento, Izabela L; Muniz, Eduardo P; Rocha, Sandra M S; Porto, Paulo S S

2018-05-01

An electrocoagulation technique using a 3.5 L reactor, with aluminum electrodes in a monopolar arrangement with polarity switch at each 10 s was used to separate oil from synthetic oily water similar in oil concentration to produced water from offshore platforms. Up to 98% of oil removal was achieved after 20 min of processing. Processing time dependence of the oil removal and pH was measured and successfully adjusted to exponential models, indicating a pseudo first order behavior. Statistical analysis was used to prove that electrical conductivity and total solids depend significantly on the concentration of electrolyte (NaCl) in the medium. Oil removal depends mostly on the distance between the electrodes but is proportional to electrolyte concentration when initial pH is 8. Electrocoagulation with polarity switch maximizes the lifetime of the electrodes. The process reduced oil concentration to a value below that stipulated by law, proving it can be an efficient technology to minimize the offshore drilling impact in the environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Influence of technical processing units on chemical composition and antimicrobial activity of carrot (Daucus carrot L.) juice essential oil.

PubMed

Ma, Tingting; Luo, Jiyang; Tian, Chengrui; Sun, Xiangyu; Quan, Meiping; Zheng, Cuiping; Kang, Lina; Zhan, Jicheng

2015-03-01

The effect of three processing units (blanching, enzyme liquefaction, pasteurisation) on chemical composition and antimicrobial activity of carrot juice essential oil was investigated in this paper. A total of 36 compounds were identified by GC-MS from fresh carrot juice essential oil. The main constituents were carotol (20.20%), sabinene (12.80%), β-caryophyllene (8.04%) and α-pinene (6.05%). Compared with the oil of fresh juice, blanching and pasteurisation could significantly decrease the components of the juice essential oil, whereas enzyme liquefaction had no considerable effect on the composition of juice essential oil. With regard to the antimicrobial activity, carrot juice essential oil could cause physical damage and morphological alteration on microorganisms, while the three different processing units showed noticeable differences on the species of microorganisms, the minimum inhibitory concentration and minimum bactericidal concentration. Results revealed that the carrot juice essential oil has great potential for application as a natural antimicrobial applied in pharmaceutical and food industries. Copyright © 2014 Elsevier Ltd. All rights reserved.

Production facilities for second generation biofuels in the USA and the EU – current status and future perspectives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Janssen, Ranier; Turhollow, Jr, Anthony F.; Rutz, Dominik

2013-10-23

Second generation biofuel production facilities have been slower to reach large-scale production than was anticipated a few years ago even though in Europe, the Renewable Energy Directive has incentives for, and in the United States there are also financial incentives and, the Energy Independence and Security Act of 2007 has targets for second generation biofuels. There have been a number of facilities that have been cancelled, but starting in 2013 it appears that significant quantities of second generation biofuels will be produced. A variety of conversion processes, thermal and biological, as well as hybrids of the two is being utilized.more » There will be a variety of fuels ethanol, drop-in fuels (e.g. gasoline, diesel), biodiesel, steam, electricity, bio-oil, sugars, and chemicals; and a variety of feedstocks crop residues, wood, wood wastes, energy crops, waste oils and municipal solid waste (MSW). One approach to reducing the risk of moving from first to second generation biofuel production has been to take incremental steps such as converting the cellulosic part of grains into ethanol in addition to the starch portion. Many of the second generation biofuel facilities are co-located with first generation biofuel production facilities to share infrastructure as well as trade by-products (e.g. excess steam). One of the challenges has been financing, but both private and government sources are being utilized. Private sources include internal corporate funds and debt offerings, and venture capital. Furthermore, government sources include the U.S. federal government, the European Union, European national governments, and state and local governments.« less

Automated oil spill detection with multispectral imagery

NASA Astrophysics Data System (ADS)

Bradford, Brian N.; Sanchez-Reyes, Pedro J.

2011-06-01

In this publication we present an automated detection method for ocean surface oil, like that which existed in the Gulf of Mexico as a result of the April 20, 2010 Deepwater Horizon drilling rig explosion. Regions of surface oil in airborne imagery are isolated using red, green, and blue bands from multispectral data sets. The oil shape isolation procedure involves a series of image processing functions to draw out the visual phenomenological features of the surface oil. These functions include selective color band combinations, contrast enhancement and histogram warping. An image segmentation process then separates out contiguous regions of oil to provide a raster mask to an analyst. We automate the detection algorithm to allow large volumes of data to be processed in a short time period, which can provide timely oil coverage statistics to response crews. Geo-referenced and mosaicked data sets enable the largest identified oil regions to be mapped to exact geographic coordinates. In our simulation, multispectral imagery came from multiple sources including first-hand data collected from the Gulf. Results of the simulation show the oil spill coverage area as a raster mask, along with histogram statistics of the oil pixels. A rough square footage estimate of the coverage is reported if the image ground sample distance is available.

Successful performance of a refinery with Eureka unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirotani, Y.; Takeuchi, T.; Miyabuchi, Y.

1981-03-01

Since starting in February, 1976, 3,400,000 Kl of vacuum residue (13,000,000 Kl of crude oil equivalent) has been successfully processed in the Eureka unit of Fuji Oil refinery complex and more than 2,500,000 Kl of cracked oil and 1,000,000 tons of pitch have been produced. The operation rate has been 94 to 98% except for the annual shutdown period for inspection. The cracked oil is easily desulfurized to make naphta, diesel oil and a large amount of gas oil (low sulfur fuel oil, 0.1 wt % sulfur). As for the desulfurization of cracked oil, the increase in H/sub 2/ consumptionmore » and the decline of catalyst life are observed. However, the operation conditions do not differ much from those for straight run fractions. Processing both hydrotreated and untreated cracked heavy oil (CHO) with FCC unit has proved to be possible. In case of untreated CHO, however, it causes a slight increase in make up catalyst and coke yield. It is demonstrated that heavy crude oils, such as Bachaquero, can effectively be processed in this system. No additional pollution problems have occurred by introducing an Eureka unit to the refinery, although it is located in the district where the most stringent environmental regulations are urged.« less

Technoeconomic assumptions adopted for the development of a long-term electricity supply model for Cyprus.

PubMed

Taliotis, Constantinos; Taibi, Emanuele; Howells, Mark; Rogner, Holger; Bazilian, Morgan; Welsch, Manuel

2017-10-01

The generation mix of Cyprus has been dominated by oil products for decades. In order to conform with European Union and international legislation, a transformation of the supply system is called for. Energy system models can facilitate energy planning into the future, but a large volume of data is required to populate such models. The present data article provides information on key modelling assumptions and input data adopted with the aim of representing the electricity supply system of Cyprus in a separate research article. Data in regards to renewable energy technoeconomic characteristics and investment cost projections, fossil fuel price projections, storage technology characteristics and system operation assumptions are described in this article.

Natural Oils for Skin-Barrier Repair: Ancient Compounds Now Backed by Modern Science.

PubMed

Vaughn, Alexandra R; Clark, Ashley K; Sivamani, Raja K; Shi, Vivian Y

2018-02-01

Natural plant oils are commonly used as topical therapy worldwide. They are usually easily accessible and are relatively inexpensive options for skin care. Many natural oils possess specific compounds with antimicrobial, antioxidant, anti-inflammatory, and anti-itch properties, making them attractive alternative and complementary treatments for xerotic and inflammatory dermatoses associated with skin-barrier disruption. Unique characteristics of various oils are important when considering their use for topical skin care. Differing ratios of essential fatty acids are major determinants of the barrier repair benefits of natural oils. Oils with a higher linoleic acid to oleic acid ratio have better barrier repair potential, whereas oils with higher amounts of irritating oleic acid may be detrimental to skin-barrier function. Various extraction methods for oils exist, including cold pressing to make unrefined oils, heat and chemical distillation to make essential oils, and the addition of various chemicals to simulate a specific scent to make fragranced oils. The method of oil processing and refinement is an important component of selecting oil for skin care, and cold pressing is the preferred method of oil extraction as the heat- and chemical-free process preserves beneficial lipids and limits irritating byproducts. This review summarizes evidence on utility of natural plant-based oils in dermatology, particularly in repairing the natural skin-barrier function, with the focus on natural oils, including Olea europaea (olive oil), Helianthus annus (sunflower seed oil), Cocos nucifera (coconut oil), Simmondsia chinesis (jojoba oil), Avena sativa (oat oil), and Argania spinosa (argan oil).

MODELING METHODOLOGIES FOR OIL SPILLS

EPA Science Inventory

Oil spilled into aquatic environments is subject to a number of fates, including natural dispersion, emulsification and weathering. An oil slick moves due to the inherent spreading of the oil, currents, winds and waves. All of these processes influence the impacts of the oil on...

Low-rank coal oil agglomeration product and process

DOEpatents

Knudson, Curtis L.; Timpe, Ronald C.; Potas, Todd A.; DeWall, Raymond A.; Musich, Mark A.

1992-01-01

A selectively-sized, raw, low-rank coal is processed to produce a low ash and relative water-free agglomerate with an enhanced heating value and a hardness sufficient to produce a non-decrepitating, shippable fuel. The low-rank coal is treated, under high shear conditions, in the first stage to cause ash reduction and subsequent surface modification which is necessary to facilitate agglomerate formation. In the second stage the treated low-rank coal is contacted with bridging and binding oils under low shear conditions to produce agglomerates of selected size. The bridging and binding oils may be coal or petroleum derived. The process incorporates a thermal deoiling step whereby the bridging oil may be completely or partially recovered from the agglomerate; whereas, partial recovery of the bridging oil functions to leave as an agglomerate binder, the heavy constituents of the bridging oil. The recovered oil is suitable for recycling to the agglomeration step or can serve as a value-added product.

Low-rank coal oil agglomeration product and process

DOEpatents

Knudson, C.L.; Timpe, R.C.; Potas, T.A.; DeWall, R.A.; Musich, M.A.

1992-11-10

A selectively-sized, raw, low-rank coal is processed to produce a low ash and relative water-free agglomerate with an enhanced heating value and a hardness sufficient to produce a non-degradable, shippable fuel. The low-rank coal is treated, under high shear conditions, in the first stage to cause ash reduction and subsequent surface modification which is necessary to facilitate agglomerate formation. In the second stage the treated low-rank coal is contacted with bridging and binding oils under low shear conditions to produce agglomerates of selected size. The bridging and binding oils may be coal or petroleum derived. The process incorporates a thermal deoiling step whereby the bridging oil may be completely or partially recovered from the agglomerate; whereas, partial recovery of the bridging oil functions to leave as an agglomerate binder, the heavy constituents of the bridging oil. The recovered oil is suitable for recycling to the agglomeration step or can serve as a value-added product.

Comparison of Different Classification Methods for Analyzing Electronic Nose Data to Characterize Sesame Oils and Blends

PubMed Central

Shao, Xiaolong; Li, Hui; Wang, Nan; Zhang, Qiang

2015-01-01

An electronic nose (e-nose) was used to characterize sesame oils processed by three different methods (hot-pressed, cold-pressed, and refined), as well as blends of the sesame oils and soybean oil. Seven classification and prediction methods, namely PCA, LDA, PLS, KNN, SVM, LASSO and RF, were used to analyze the e-nose data. The classification accuracy and MAUC were employed to evaluate the performance of these methods. The results indicated that sesame oils processed with different methods resulted in different sensor responses, with cold-pressed sesame oil producing the strongest sensor signals, followed by the hot-pressed sesame oil. The blends of pressed sesame oils with refined sesame oil were more difficult to be distinguished than the blends of pressed sesame oils and refined soybean oil. LDA, KNN, and SVM outperformed the other classification methods in distinguishing sesame oil blends. KNN, LASSO, PLS, and SVM (with linear kernel), and RF models could adequately predict the adulteration level (% of added soybean oil) in the sesame oil blends. Among the prediction models, KNN with k = 1 and 2 yielded the best prediction results. PMID:26506350

Synthesis and Performance Evaluation of a New Deoiling Agent for Treatment of Waste Oil-Based Drilling Fluids

PubMed Central

Liu, Pingting; Huang, Zhiyu; Deng, Hao; Wang, Rongsha; Xie, Shuixiang

2014-01-01

Oil-based drilling fluid is used more and more in the field of oil and gas exploration. However, because of unrecyclable treating agent and hard treatment conditions, the traditional treating technologies of waste oil-based drilling fluid have some defects, such as waste of resource, bulky equipment, complex treatment processes, and low oil recovery rate. In this work, switchable deoiling agent (SDA), as a novel surfactant for treatment of waste oil-based drilling fluid, was synthesized by amine, formic acid, and formaldehyde solution. With this agent, the waste oil-based drilling fluid can be treated without complex process and expensive equipment. Furthermore, the agent used in the treatment can be recycled, which reduces waste of resource and energy. The switch performance, deoiling performance, structural characterization, and mechanisms of action are studied. The experimental results show that the oil content of the recycled oil is higher than 96% and more than 93% oil in waste oil-based drilling fluid can be recycled. The oil content of the solid residues of deoiling is less than 3%. PMID:25045749

Synthesis and performance evaluation of a new deoiling agent for treatment of waste oil-based drilling fluids.

PubMed

Liu, Pingting; Huang, Zhiyu; Deng, Hao; Wang, Rongsha; Xie, Shuixiang

2014-01-01

Oil-based drilling fluid is used more and more in the field of oil and gas exploration. However, because of unrecyclable treating agent and hard treatment conditions, the traditional treating technologies of waste oil-based drilling fluid have some defects, such as waste of resource, bulky equipment, complex treatment processes, and low oil recovery rate. In this work, switchable deoiling agent (SDA), as a novel surfactant for treatment of waste oil-based drilling fluid, was synthesized by amine, formic acid, and formaldehyde solution. With this agent, the waste oil-based drilling fluid can be treated without complex process and expensive equipment. Furthermore, the agent used in the treatment can be recycled, which reduces waste of resource and energy. The switch performance, deoiling performance, structural characterization, and mechanisms of action are studied. The experimental results show that the oil content of the recycled oil is higher than 96% and more than 93% oil in waste oil-based drilling fluid can be recycled. The oil content of the solid residues of deoiling is less than 3%.

Current Options for Determining Fracture Union

PubMed Central

2014-01-01

Determining whether a bone fracture is healed is one of the most important and fundamental clinical determinations made in orthopaedics. However, there are currently no standardized methods of assessing fracture union, which in turn has created significant disagreement among orthopaedic surgeons in both clinical and research settings. An extensive amount of research has been dedicated to finding novel and reliable ways of determining healing with some promising results. Recent advancements in imaging techniques and introduction of new radiographic scores have helped decrease the amount of disagreement on this topic among physicians. The knowledge gained from biomechanical studies of bone healing has helped us refine our tools and create more efficient and practical research instruments. Additionally, a deeper understanding of the molecular pathways involved in the bone healing process has led to emergence of serologic markers as possible candidates in assessment of fracture union. In addition to our current physician centered methods, patient-centered approaches assessing quality of life and function are gaining popularity in assessment of fracture union. Despite these advances, assessment of union remains an imperfect practice in the clinical setting. Therefore, clinicians need to draw on multiple modalities that directly and indirectly measure or correlate with bone healing when counseling patients. PMID:26556422

Oil-shale program

NASA Astrophysics Data System (ADS)

Bader, B. E.

1981-10-01

The principal activities of the Sandia National Laboratories in the Department of Energy Oil shale program during the period April 1 to June 30, 1981 are discussed. Currently, Sandia's activities are focused upon: the development and use of analytical and experimental modeling techniques to describe and predict the retort properties and retorting process parameters that are important to the preparation, operation, and stability of in situ retorts, and the development, deployment, and field use of instrumentation, data acquisition, and process monitoring systems to characterize and evaluate in site up shale oil recovery operations. In-house activities and field activities (at the Geokinetics Oil Shale Project and the Occidental Oil Shale Project) are described under the headings: bed preparation, bed characterization, retorting process, and structural stability.

How Specific Microbial Communities Benefit the Oil Industry: Biorefining and Bioprocessing for Upgrading Petroleum Oil

NASA Astrophysics Data System (ADS)

Singh, Ajay

Recent advances in molecular biology of microbes have made possible in exploring and engineering improved biocatalysts (microbes and enzymes) suitable for the oil biorefining and recovery processes (Monticello, 2000; Van Hamme et al., 2003; Kilbane, 2006). Crude oil contains about 0.05-5% sulphur, 0.5-2.1% nitrogen and heavy metals such as nickel and vanadium associated with the asphaltene fraction. High temperature- and pressure-requiring expensive hydrotreatment processes are generally used to remove sulphur and nitrogen compounds from petroleum. Biorefining processes to improve oil quality have gained lots of interest and made a significant progress in the last two decades (Le Borgne and Quintero, 2003) and is the focus of this chapter.

Aligning food-processing policies to promote healthier fat consumption in India

PubMed Central

Downs, Shauna M.; Marie Thow, Anne; Ghosh-Jerath, Suparna; Leeder, Stephen R.

2015-01-01

India is undergoing a shift in consumption from traditional foods to processed foods high in sugar, salt and fat. Partially hydrogenated vegetable oils (PHVOs) high in trans-fat are often used in processed foods in India given their low cost and extended shelf life. The World Health Organization has called for the elimination of PHVOs from the global food supply and recommends their replacement with polyunsaturated fat to maximize health benefits. This study examined barriers to replacing industrially produced trans-fat in the Indian food supply and systematically identified potential policy solutions to assist the government in encouraging its removal and replacement with healthier polyunsaturated fat. A combination of food supply chain analysis and semi-structured interviews with key stakeholders was conducted. The main barriers faced by the food-processing sector in terms of reducing use of trans-fat and replacing it with healthier oils in India were the low availability and high cost of oils high in polyunsaturated fats leading to a reliance on palm oil (high in saturated fat) and the low use of those healthier oils in product reformulation. Improved integration between farmers and processors, investment in technology and pricing strategies to incentivize use of healthier oils for product reformulation were identified as policy options. Food processors have trouble accessing sufficient affordable healthy oils for product reformulation, but existing incentives aimed at supporting food processing could be tweaked to ensure a greater supply of healthy oils with the potential to improve population health. PMID:24399031

[Study on two preparation methods for beta-CD inclusion compound of four traditional Chinese medicine volatile oils].

PubMed

Li, Hailiang; Cui, Xiaoli; Tong, Yan; Gong, Muxin

2012-04-01

To compare inclusion effects and process conditions of two preparation methods-colloid mill and saturated solution-for beta-CD inclusion compound of four traditional Chinese medicine volatile oils and study the relationship between each process condition and volatile oil physical properties and the regularity of selective inclusion of volatile oil components. Volatile oils from Nardostachyos Radix et Rhizoma, Amomi Fructus, Zingiberis Rhizoma and Angelicaesinensis Radix were prepared using two methods in the orthogonal test. These inclusion compounds by optimized processes were assessed and compared by such methods as TLC, IR and scanning electron microscope. Inclusion oils were extracted by steam distillation, and the components found before and after inclusion were analyzed by GC-MS. Analysis showed that new inclusion compounds, but inclusion compounds prepared by the two processes had differences to some extent. The colloid mill method showed a better inclusion effect than the saturated solution method, indicating that their process conditions had relations with volatile oil physical properties. There were differences in the inclusion selectivity of components between each other. The colloid mill method for inclusion preparation is more suitable for industrial requirements. To prepare volatile oil inclusion compounds with heavy gravity and high refractive index, the colloid mill method needs longer time and more water, while the saturated solution method requires higher temperature and more beta-cyclodextrin. The inclusion complex prepared with the colloid mill method contains extended molecular weight chemical composition, but the kinds of components are reduced.

Fuel and fuel blending components from biomass derived pyrolysis oil

DOEpatents

McCall, Michael J.; Brandvold, Timothy A.; Elliott, Douglas C.

2012-12-11

A process for the conversion of biomass derived pyrolysis oil to liquid fuel components is presented. The process includes the production of diesel, aviation, and naphtha boiling point range fuels or fuel blending components by two-stage deoxygenation of the pyrolysis oil and separation of the products.

40 CFR 63.2840 - What emission requirements must I meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

... National Emission Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production... month. (e) Low-HAP solvent option. For all vegetable oil production processes subject to this subpart... paragraphs (e)(1) through (5) of this section. Your vegetable oil production process is not subject to the...

40 CFR 63.2840 - What emission requirements must I meet?

Code of Federal Regulations, 2010 CFR

2010-07-01

... National Emission Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production... month. (e) Low-HAP solvent option. For all vegetable oil production processes subject to this subpart... paragraphs (e)(1) through (5) of this section. Your vegetable oil production process is not subject to the...

Liquid oil production from shale gas condensate reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, James J.

A process of producing liquid oil from shale gas condensate reservoirs and, more particularly, to increase liquid oil production by huff-n-puff in shale gas condensate reservoirs. The process includes performing a huff-n-puff gas injection mode and flowing the bottom-hole pressure lower than the dew point pressure.

Study of weathering effects on the distribution of aromatic steroid hydrocarbons in crude oils and oil residues.

PubMed

Wang, Chuanyuan; Chen, Bing; Zhang, Baiyu; Guo, Ping; Zhao, Mingming

2014-01-01

The composition and distribution of triaromatic steroid hydrocarbons in oil residues after biodegradation and photo-oxidation processes were detected, and the diagnostic ratios for oil spill identification were developed and evaluated based on the relative standard deviation (RSD) and the repeatability limit. The preferential loss of C27 methyl triaromatic steranes (MTAS) relative to C28 MTAS and C29 MTAS was shown during the photo-oxidation process. In contrast to the photochemical degradation, the MTAS with the original 20R biological configuration was preferentially degraded during the biodegradation process. The RSD of most of the diagnostic ratios of MTAS ranged from 9 to 84% during the photo-oxidation process. However, the RSDs of such ratios derived from MTAS were all <5% even in high biodegradation, and such parameters may also provide new methods on oil spill identification. The parameters of monoaromatic sterane and monoaromatic sterane are not used well for oil spill identification after photo-oxidation. The triaromatic steroid hydrocarbons retained their molecular compositions after biodegradation and photo-oxidation and most of the diagnostic ratios derived from them could be efficiently used in oil spill identification.

On the modeling of the 2010 Gulf of Mexico Oil Spill

NASA Astrophysics Data System (ADS)

Mariano, A. J.; Kourafalou, V. H.; Srinivasan, A.; Kang, H.; Halliwell, G. R.; Ryan, E. H.; Roffer, M.

2011-09-01

Two oil particle trajectory forecasting systems were developed and applied to the 2010 Deepwater Horizon Oil Spill in the Gulf of Mexico. Both systems use ocean current fields from high-resolution numerical ocean circulation model simulations, Lagrangian stochastic models to represent unresolved sub-grid scale variability to advect oil particles, and Monte Carlo-based schemes for representing uncertain biochemical and physical processes. The first system assumes two-dimensional particle motion at the ocean surface, the oil is in one state, and the particle removal is modeled as a Monte Carlo process parameterized by a one number removal rate. Oil particles are seeded using both initial conditions based on observations and particles released at the location of the Maconda well. The initial conditions (ICs) of oil particle location for the two-dimensional surface oil trajectory forecasts are based on a fusing of all available information including satellite-based analyses. The resulting oil map is digitized into a shape file within which a polygon filling software generates longitude and latitude with variable particle density depending on the amount of oil present in the observations for the IC. The more complex system assumes three (light, medium, heavy) states for the oil, each state has a different removal rate in the Monte Carlo process, three-dimensional particle motion, and a particle size-dependent oil mixing model. Simulations from the two-dimensional forecast system produced results that qualitatively agreed with the uncertain "truth" fields. These simulations validated the use of our Monte Carlo scheme for representing oil removal by evaporation and other weathering processes. Eulerian velocity fields for predicting particle motion from data-assimilative models produced better particle trajectory distributions than a free running model with no data assimilation. Monte Carlo simulations of the three-dimensional oil particle trajectory, whose ensembles were generated by perturbing the size of the oil particles and the fraction in a given size range that are released at depth, the two largest unknowns in this problem. 36 realizations of the model were run with only subsurface oil releases. An average of these results yields that after three months, about 25% of the oil remains in the water column and that most of the oil is below 800 m.

E-nose, e-tongue and e-eye for edible olive oil characterization and shelf life assessment: A powerful data fusion approach.

PubMed

Buratti, Susanna; Malegori, Cristina; Benedetti, Simona; Oliveri, Paolo; Giovanelli, Gabriella

2018-05-15

The aim of this work was to investigate the applicability of e-senses (electronic nose, electronic tongue and electronic eye) for the characterization of edible olive oils (extra virgin, olive and pomace) and for the assessment of extra virgin olive oil and olive oil quality decay during storage at different temperatures. In order to obtain a complete description of oil samples, physico-chemical analyses on quality and nutritional parameters were also performed. Data were processed by PCA and a targeted data processing flow-sheet has been applied to physico-chemical and e-senses dataset starting from data pre-processing introducing an innovative normalization method, called t0 centering. On e-senses data a powerful mid-level data fusion approach has been employed to extract relevant information from different analytical sources combining their individual contributions. On physico-chemical data, an alternative approach for grouping extra virgin olive oil and olive oil samples on the basis of their freshness was applied and two classes were identified: fresh and oxidized. A k-NN classification rule was developed to test the performance of e-senses to classify samples in the two classes of freshness and the average value of correctly classified samples was 94%. Results demonstrated that the combined application of e-senses and the innovative data processing strategy allows to characterize edible olive oils of different categories on the basis of their sensorial properties and also to follow the evolution during storage of extra-virgin olive oil and olive oil sensorial properties thus assessing the quality decay of oils. Copyright © 2018 Elsevier B.V. All rights reserved.

Cation Exchange in the Presence of Oil in Porous Media

PubMed Central

2017-01-01

Cation exchange is an interfacial process during which cations on a clay surface are replaced by other cations. This study investigates the effect of oil type and composition on cation exchange on rock surfaces, relevant for a variety of oil-recovery processes. We perform experiments in which brine with a different composition than that of the in situ brine is injected into cores with and without remaining oil saturation. The cation-exchange capacity (CEC) of the rocks was calculated using PHREEQC software (coupled to a multipurpose transport simulator) with the ionic composition of the effluent histories as input parameters. We observe that in the presence of crude oil, ion exchange is a kinetically controlled process and its rate depends on residence time of the oil in the pore, the temperature, and kinetic rate of adsorption of the polar groups on the rock surface. The cation-exchange process occurs in two stages during two phase flow in porous media. Initially, the charged sites of the internal surface of the clays establish a new equilibrium by exchanging cations with the aqueous phase. At later stages, the components of the aqueous and oleic phases compete for the charged sites on the external surface or edges of the clays. When there is sufficient time for crude oil to interact with the rock (i.e., when the core is aged with crude oil), a fraction of the charged sites are neutralized by the charged components stemming from crude oil. Moreover, the positively charged calcite and dolomite surfaces (at the prevailing pH environment of our experiments) are covered with the negatively charged components of the crude oil and therefore less mineral dissolution takes place when oil is present in porous media. PMID:28580442

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.; Germain, R.R.

1989-01-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulphur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgradermore » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional projects, also based on hydrogenation, will use ebullated bed catalyst systems; the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.

1988-06-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulfur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgrader,more » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional products, also based on hydrogenation, will use ebullated bed catalyst systems: the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Profitability Analysis of Soybean Oil Processes.

PubMed

Cheng, Ming-Hsun; Rosentrater, Kurt A

2017-10-07

Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV), break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP), is profitable when the capacity is larger than 17 million kg of annual oil production.

Profitability Analysis of Soybean Oil Processes

PubMed Central

2017-01-01

Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV), break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP), is profitable when the capacity is larger than 17 million kg of annual oil production. PMID:28991168

Process for recovering uranium from waste hydrocarbon oils containing the same. [Uranium contaminated lubricating oils from gaseous diffusion compressors

DOEpatents

Conrad, M.C.; Getz, P.A.; Hickman, J.E.; Payne, L.D.

1982-06-29

The invention is a process for the recovery of uranium from uranium-bearing hydrocarbon oils containing carboxylic acid as a degradation product. In one aspect, the invention comprises providing an emulsion of water and the oil, heating the same to a temperature effecting conversion of the emulsion to an organic phase and to an acidic aqueous phase containing uranium carboxylate, and recovering the uranium from the aqueous phase. The process is effective, simple and comparatively inexpensive. It avoids the use of toxic reagents and the formation of undesirable intermediates.

Selective separation of oil and water with mesh membranes by capillarity.

PubMed

Yu, Yuanlie; Chen, Hua; Liu, Yun; Craig, Vincent S J; Lai, Zhiping

2016-09-01

The separation of oil and water from wastewater generated in the oil-production industries, as well as in frequent oil spillage events, is important in mitigating severe environmental and ecological damage. Additionally, a wide arrange of industrial processes require oils or fats to be removed from aqueous systems. The immiscibility of oil and water allows for the wettability of solid surfaces to be engineered to achieve the separation of oil and water through capillarity. Mesh membranes with extreme, selective wettability can efficiently remove oil or water from oil/water mixtures through a simple filtration process using gravity. A wide range of different types of mesh membranes have been successfully rendered with extreme wettability and applied to oil/water separation in the laboratory. These mesh materials have typically shown good durability, stability as well as reusability, which makes them promising candidates for an ever widening range of practical applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Improvement of neutral oil quality in the production of sulfonate additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhurba, A.S.; Bludilin, V.M.; Antonov, V.N.

This paper is concerned with improvement of neutral oil used as materials for sulfonation to produce additives for lubricating oils. In this article the authors analyze the basic reasons for the unsatisfactory quality of the neutral oil and attempt to define the ways in which the process technology can be improved so as to produce neutral oil with the required composition, at the same time raising the efficiency of utilization of the MSG-8 oil used as a feedstock for this process. Experimental results are presented which demonstrate the feasibility of sulfonating neutral oil in the high-speed mixer under near-optimal conditions.more » The yield of sulfonic acid approaches the theoretical yield. With the lowest contents of aromatic hydrocarbons in the original neutral oil, the aromatic hydrocarbons are almost completely converted to sulfonic acids. The yield of neutral oil is sufficiently high, and the residual content of aromatic hydrocarbons in the oil is no greater than 3%.« less

Feasibility Process for Remediation of the Crude Oil Contaminated Soil

NASA Astrophysics Data System (ADS)

Keum, H.; Choi, H.; Heo, H.; Lee, S.; Kang, G.

2015-12-01

More than 600 oil wells were destroyed in Kuwait by Iraqi in 1991. During the war, over 300 oil lakes with depth of up to 2m at more than 500 different locations which has been over 49km2. Therefore, approximately 22 million m3was crude oil contaminated. As exposure of more than 20 years under atmospheric conditions of Kuwait, the crude oil has volatile hydrocarbons and covered heavy oily sludge under the crude oil lake. One of crude oil contaminated soil which located Burgan Oilfield area was collected by Kuwait Oil Company and got by H-plus Company. This contaminated soil has about 42% crude oil and could not biodegraded itself due to the extremely high toxicity. This contaminated soil was separated by 2mm sieve for removal oil sludge ball. Total petroleum hydrocarbons (TPH) was analysis by GC FID and initial TPH concentration was average 48,783 mg/kg. Ten grams of the contaminated soil replaced in two micro reactors with 20mL of bio surfactant produce microorganism. Reactor 1 was added 0.1g powder hemoglobin and other reactor was not added hemoglobin at time 0 day. Those reactors shake 120 rpm on the shaker for 7 days and CO2 produced about 150mg/L per day. After 7 days under the slurry systems, the rest days operated by hemoglobin as primary carbon source for enhanced biodegradation. The crude oil contaminated soil was degraded from 48,783mg/kg to 20,234mg/kg by slurry process and final TPH concentration degraded 11,324mg/kg for 21days. Therefore, highly contaminated soil by crude oil will be combined bio slurry process and biodegradation process with hemoglobin as bio catalytic source. Keywords: crude-oil contaminated soil, bio slurry, biodegradation, hemoglobin ACKOWLEDGEMENTS This project was supported by the Korea Ministry of Environment (MOE) GAIA Program

Process for producing modified microorganisms for oil treatment at high temperatures, pressures and salinity

DOEpatents

Premuzic, Eugene T.; Lin, Mow

1996-02-20

This invention relates to the preparation of new, modified organisms, through challenge growth processes, that are viable in the extreme temperature, pressure and pH conditions and salt concentrations of an oil reservoir and that are suitable for use in microbial enhanced oil recovery. The modified microorganisms of the present invention are used to enhance oil recovery and remove sulfur compounds and metals from the crude oil. The processes are comprised of steps which successively limit the carbon sources and increase the temperature, pressure and salinity of the media. This is done until microbial strains are obtained that are capable of growing in essentially crude oil as a carbon source and at a temperature range from about 70.degree. C. to 90.degree. C., at a pressure range from about 2,000 to 2,500 psi and at a salinity range from about 1.3 to 35%.

Process for producing modified microorganisms for oil treatment at high temperatures, pressures and salinity

DOEpatents

Premuzic, E.T.; Lin, M.

1996-02-20

This invention relates to the preparation of new, modified organisms, through challenge growth processes, that are viable in the extreme temperature, pressure and pH conditions and salt concentrations of an oil reservoir and that are suitable for use in microbial enhanced oil recovery. The modified microorganisms of the present invention are used to enhance oil recovery and remove sulfur compounds and metals from the crude oil. The processes are comprised of steps which successively limit the carbon sources and increase the temperature, pressure and salinity of the media. This is done until microbial strains are obtained that are capable of growing in essentially crude oil as a carbon source and at a temperature range from about 70 C to 90 C, at a pressure range from about 2,000 to 2,500 psi and at a salinity range from about 1.3 to 35%. 68 figs.

Evaluation of processing factors for selected organic contaminants during virgin olive oil production: Distribution of BTEXS during olives processing.

PubMed

López-Blanco, Rafael; Gilbert-López, Bienvenida; Rojas-Jiménez, Rubén; Robles-Molina, José; Ramos-Martos, Natividad; García-Reyes, Juan F; Molina-Díaz, Antonio

2016-05-15

The presence of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) in virgin olive oils can be attributed to environmental contamination, but also to biological processes during oil lipogenesis (styrene). In this work, the processing factor of BTEXS from olives to olive oil during its production was evaluated at lab-scale with an Abencor system. Benzene showed the lowest processing factor (15%), whereas toluene and xylenes showed an intermediate behavior (with 40-60% efficiency), and ethylbenzene and styrene were completely transferred (100%). In addition, an attempt to examine the contribution of potential sources to olives contamination with BTEXS was carried out for the first time. Two types of olives samples were classified according to their proximity to the contamination source (road). Although higher levels of BTEXS were found in samples close to roads, the concentrations were relatively low and do not constitute a major contribution to BTEXS usually detected in olive oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

pH Neutralization of Aqueous Bio-Oil from Switchgrass Intermediate Pyrolysis Using Process Intensification Devices

DOE PAGES

Park, Lydia Kyoung-Eun; Ren, Shoujie; Yiacoumi, Sotira; ...

2017-07-20

Despite the potential carbon-neutrality of switchgrass bio-oil, its high acidity and diverse chemical composition limit its utilization. The objectives of this research are to investigate pH neutralization of bio-oil by adding various alkali solutions in a batch system and then perform neutralization using process intensification devices, including a static mixer and a centrifugal contactor. The results indicate that sodium hydroxide and potassium hydroxide are more appropriate bases for pH neutralization of bio-oil than calcium hydroxide due to the limited solubility of calcium hydroxide in aqueous bio-oil. Mass and total acid number (TAN) balances were performed for both batch and continuous-flowmore » systems. Upon pH neutralization of bio-oil, the TAN values of the system increased after accounting the addition of alkali solution. A bio-oil heating experiment showed that the heat generated during pH neutralization did not cause a significant increase in the acidity of bio-oil. The formation of phenolic compounds during neutralization was initially suspected of increasing the system’s overall TAN value because some of these compounds (e.g., vanillic acid) act as polyprotic acids and have a stronger influence on the TAN value than monoprotic acids (e.g., acetic acid). The amount of phenolics in separated bio-oil phases, however, did not change significantly after pH neutralization. In conclusion, process intensification devices provided sufficient mixing and separation of the organic and aqueous phases, suggesting a scale-up route for the bio-oil pH neutralization process.« less

Using Polymer Alternating Gas to Enhance Oil Recovery in Heavy Oil

NASA Astrophysics Data System (ADS)

Yang, Yongzhi; Li, Weirong; Zhou, Tiyao; Dong, Zhenzhen

2018-02-01

CO2 has been used to recover oil for more than 40 years. Currently, about 43% of EOR production in U.S. is from CO2 flooding. CO2 flooding is a well-established EOR technique, but its density and viscosity nature are challenges for CO2 projects. Low density (0.5 to 0.8 g/cm3) causes gas to rise upward in reservoirs and bypass many lower portions of the reservoir. Low viscosity (0.02 to 0.08 cp) leads to poor volumetric sweep efficiency. So water-alternating-gas (WAG) method was used to control the mobility of CO2 and improve sweep efficiency. However, WAG process has some other problems in heavy oil reservoir, such as poor mobility ratio and gravity overriding. To examine the applicability of carbon dioxide to recover viscous oil from highly heterogeneous reservoirs, this study suggests a new EOR method--polymer-alternating gas (PAG) process. The process involves a combination of polymer flooding and CO2 injection. To confirm the effectiveness of PAG process in heavy oils, a reservoir model from Liaohe Oilfield is used to compare the technical and economic performance among PAG, WAG and polymer flooding. Simulation results show that PAG method would increase oil recovery over 10% compared with other EOR methods and PAG would be economically success based on assumption in this study. This study is the first to apply PAG to enhance oil recovery in heavy oil reservoir with highly heterogeneous. Besides, this paper provides detailed discussions and comparison about PAG with other EOR methods in this heavy oil reservoir.

pH Neutralization of Aqueous Bio-Oil from Switchgrass Intermediate Pyrolysis Using Process Intensification Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Lydia Kyoung-Eun; Ren, Shoujie; Yiacoumi, Sotira

Despite the potential carbon-neutrality of switchgrass bio-oil, its high acidity and diverse chemical composition limit its utilization. The objectives of this research are to investigate pH neutralization of bio-oil by adding various alkali solutions in a batch system and then perform neutralization using process intensification devices, including a static mixer and a centrifugal contactor. The results indicate that sodium hydroxide and potassium hydroxide are more appropriate bases for pH neutralization of bio-oil than calcium hydroxide due to the limited solubility of calcium hydroxide in aqueous bio-oil. Mass and total acid number (TAN) balances were performed for both batch and continuous-flowmore » systems. Upon pH neutralization of bio-oil, the TAN values of the system increased after accounting the addition of alkali solution. A bio-oil heating experiment showed that the heat generated during pH neutralization did not cause a significant increase in the acidity of bio-oil. The formation of phenolic compounds during neutralization was initially suspected of increasing the system’s overall TAN value because some of these compounds (e.g., vanillic acid) act as polyprotic acids and have a stronger influence on the TAN value than monoprotic acids (e.g., acetic acid). The amount of phenolics in separated bio-oil phases, however, did not change significantly after pH neutralization. In conclusion, process intensification devices provided sufficient mixing and separation of the organic and aqueous phases, suggesting a scale-up route for the bio-oil pH neutralization process.« less

Electrochemical Upgrading of Bio-Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elangovan, S.; Larsen, Dennis; Bay, Insoo

Bio-oil produced by fast pyrolysis of biomass is a potential source of low carbon, renewable hydrocarbon fuel. However, the properties such as low heating value, incomplete volatility, acidity, instability, and incompatibility with standard fuels restrict its use. The undesirable properties of pyrolysis oil result from its chemical composition that mostly consists of different classes of oxygenated organic compounds. Current process of Hydrodeoxygenation to remove oxygen involves high-temperature, high-pressure processing in the presence of hydrogen and catalyst. An alternative process of deoxygenation of bio-oil using solid-state, oxygen conductor based electrochemical cell is under investigation. The electrolysis process removes oxygen from themore » oxygenated organic molecule as well from steam to produce hydrogen in-situ allowing for a distributed, small scale integrated upgrading unit. Mixtures of model compounds and a slip stream of pyrolysis vapor were tested. The results show the potential for integrating a pyrolyzer and an electrochemical device for stabilizing pyrolysis oil.« less

Oil shale derived pollutant control materials and methods and apparatuses for producing and utilizing the same

DOEpatents

Boardman, Richard D.; Carrington, Robert A.

2010-05-04

Pollution control substances may be formed from the combustion of oil shale, which may produce a kerogen-based pyrolysis gas and shale sorbent, each of which may be used to reduce, absorb, or adsorb pollutants in pollution producing combustion processes, pyrolysis processes, or other reaction processes. Pyrolysis gases produced during the combustion or gasification of oil shale may also be used as a combustion gas or may be processed or otherwise refined to produce synthetic gases and fuels.

The effect of the natural bentonite to reduce COD in palm oil mill effluent by using a hybrid adsorption-flotation method

NASA Astrophysics Data System (ADS)

Dewi, Ratni; Sari, Ratna; Syafruddin

2017-06-01

Palm oil mill effluent is waste produced from palm oil processing activities. This waste are comingfrom condensate water, process water and hydrocyclone water. The high levels of contaminants in the palm oil mill effluent causes the waste becomes inappropriate to be discharged to water body before processing, one of the most major contaminants in wastewater is fats, oils and COD.This study investigated the effectiveness of chemically activated bentonite that serves as an alternative to reduce the COD in adsorption and floatation based palm oil effluent waste processing. Natural bentonite was activated by using nitrit acid and benzene. In the existing adsorption material to improve COD reduction capability whereas the flotation method was used to further remove residual effluent which is still remain after the adsorption process. An adsorption columns which operated in batch was used in the present study. By varying the circulation time and adsorbent treatment (activated and non-activated), it was shown that percentage of COD reduction reached 75% at the circulation time of 180 minutes for non activated adsorbent. On the other hand the percentof COD reduction in adsorption and flotation process using activated bentonite reached as high as 88% and 93% at the circulation time of 180 minutes.

Climate impacts of oil extraction increase significantly with oilfield age

NASA Astrophysics Data System (ADS)

Masnadi, Mohammad S.; Brandt, Adam R.

2017-08-01

Record-breaking temperatures have induced governments to implement targets for reducing future greenhouse gas (GHG) emissions. Use of oil products contributes ~35% of global GHG emissions, and the oil industry itself consumes 3-4% of global primary energy. Because oil resources are becoming increasingly heterogeneous, requiring different extraction and processing methods, GHG studies should evaluate oil sources using detailed project-specific data. Unfortunately, prior oil-sector GHG analysis has largely neglected the fact that the energy intensity of producing oil can change significantly over the life of a particular oil project. Here we use decades-long time-series data from twenty-five globally significant oil fields (>1 billion barrels ultimate recovery) to model GHG emissions from oil production as a function of time. We find that volumetric oil production declines with depletion, but this depletion is accompanied by significant growth--in some cases over tenfold--in per-MJ GHG emissions. Depletion requires increased energy expenditures in drilling, oil recovery, and oil processing. Using probabilistic simulation, we derive a relationship for estimating GHG increases over time, showing an expected doubling in average emissions over 25 years. These trends have implications for long-term emissions and climate modelling, as well as for climate policy.

Labor-Management Cooperation in Illinois: How a Joint Union Company Team Is Improving Facility Safety.

PubMed

Mahan, Bruce; Maclin, Reggie; Ruttenberg, Ruth; Mundy, Keith; Frazee, Tom; Schwartzkopf, Randy; Morawetz, John

2018-01-01

This study of Afton Chemical Corporation's Sauget facility and its International Chemical Workers Union Council (ICWUC) Local 871C demonstrates how significant safety improvements can be made when committed leadership from both management and union work together, build trust, train the entire work force in U.S. Occupational Safety and Health Administration 10-hour classes, and communicate with their work force, both salaried and hourly. A key finding is that listening to the workers closest to production can lead to solutions, many of them more cost-efficient than top-down decision-making. Another is that making safety and health an authentic value is hard work, requiring time, money, and commitment. Third, union and management must both have leadership willing to take chances and learn to trust one another. Fourth, training must be for everyone and ongoing. Finally, health and safety improvements require dedicated funding. The result was resolution of more than one hundred safety concerns and an ongoing institutionalized process for continuing improvement.

Optimization of palm oil physical refining process for reduction of 3-monochloropropane-1,2-diol (3-MCPD) ester formation.

PubMed

Zulkurnain, Musfirah; Lai, Oi Ming; Tan, Soo Choon; Abdul Latip, Razam; Tan, Chin Ping

2013-04-03

The reduction of 3-monochloropropane-1,2-diol (3-MCPD) ester formation in refined palm oil was achieved by incorporation of additional processing steps in the physical refining process to remove chloroester precursors prior to the deodorization step. The modified refining process was optimized for the least 3-MCPD ester formation and acceptable refined palm oil quality using response surface methodology (RSM) with five processing parameters: water dosage, phosphoric acid dosage, degumming temperature, activated clay dosage, and deodorization temperature. The removal of chloroester precursors was largely accomplished by increasing the water dosage, while the reduction of 3-MCPD esters was a compromise in oxidative stability and color of the refined palm oil because some factors such as acid dosage, degumming temperature, and deodorization temperature showed contradictory effects. The optimization resulted in 87.2% reduction of 3-MCPD esters from 2.9 mg/kg in the conventional refining process to 0.4 mg/kg, with color and oil stability index values of 2.4 R and 14.3 h, respectively.

Co-cracking of bio-oil distillate bottoms with vacuum gas oil for enhanced production of light compounds

USDA-ARS?s Scientific Manuscript database

Seamless co-processing of pyrolysis bio-oil within existing petroleum refineries is the most synergistic and economic way to improve biorefinery output. Coprocessing bio-oil with vacuum gas oil (VGO) is one logical pathway. Bio-oil has a viscosity and molecular weight range similar to that of VGO, a...

Method of operating an oil shale kiln

DOEpatents

Reeves, Adam A.

1978-05-23

Continuously determining the bulk density of raw and retorted oil shale, the specific gravity of the raw oil shale and the richness of the raw oil shale provides accurate means to control process variables of the retorting of oil shale, predicting oil production, determining mining strategy, and aids in controlling shale placement in the kiln for the retorting.

Coal-oil coprocessing at HTI - development and improvement of the technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stalzer, R.H.; Lee, L.K.; Hu, J.

1995-12-31

Co-Processing refers to the combined processing of coal and petroleum-derived heavy oil feedstocks. The coal feedstocks used are those typically utilized in direct coal liquefaction: bituminous, subbituminous, and lignites. Petroleum-derived oil, is typically a petroleum residuum, containing at least 70 W% material boiling above 525{degrees}C. The combined coal and oil feedstocks are processed simultaneously with the dual objective of liquefying the coal and upgrading the petroleum-derived residuum to lower boiling (<525{degrees}C) premium products. HTI`s investigation of the Co-Processing technology has included work performed in laboratory, bench and PDU scale operations. The concept of co-processing technology is quite simple and amore » natural outgrowth of the work done with direct coal liquefaction. A 36 month program to evaluate new process concepts in coal-oil coprocessing at the bench-scale was begun in September 1994 and runs until September 1997. Included in this continuous bench-scale program are provisions to examine new improvements in areas such as: interstage product separation, feedstock concentrations (coal/oil), improved supported/dispersed catalysts, optimization of reactor temperature sequencing, and in-line hydrotreating. This does not preclude other ideas from DOE contracts and other sources that can lead to improved product quality and economics. This research work has led to important findings which significantly increased liquid yields, improved product quality, and improved process economics.« less

Subcritical hydrothermal liquefaction of cattle manure to bio-oil: Effects of conversion parameters on bio-oil yield and characterization of bio-oil.

PubMed

Yin, Sudong; Dolan, Ryan; Harris, Matt; Tan, Zhongchao

2010-05-01

In this study, cattle manure was converted to bio-oil by subcritical hydrothermal liquefaction in the presence of NaOH. The effects of conversion temperature, process gas, initial conversion pressure, residence time and mass ratio of cattle manure to water on the bio-oil yield were studied. The bio-oil was characterized in terms of elemental composition, higher heating value, ultraviolet-visible (UV/Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). Results showed that the bio-oil yield depended on the conversion temperature and the process gas. Higher initial conversion pressure, longer residence time and larger mass ratio of cattle manure to water, however, had negative impacts on the bio-oil yield. The higher heating value of bio-oil was 35.53MJ/kg on average. The major non-polar components of bio-oil were toluene, ethyl benzene and xylene, which are components of crude oil, gasoline and diesel. Copyright 2010 Elsevier Ltd. All rights reserved.

DEMONSTRATION BULLETIN: THE DEHYDRO-TECH CORP. CARVER-GREENFIELD PROCESS

EPA Science Inventory

The Carver-Greenfield (C-G) Process (Figure 1) is a physical process that separates hazardous oil-soluble organic contaminants from sludges, soils, and non-aqueous liquids. The process involves adding to the waste a "carrier" oil, which removes hazardous organics from contamin...

Lubricant base oil and wax processing. [Glossary included

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sequeira, A. Jr.

1994-01-01

This book provides state-of-the-art information on all processes currently used to manufacture lubricant base oils and waxes. It furnishes helpful lists of conversion factors, construction cost data, and process licensors, as well as a glossary of essential petroleum processing terms.

Enzymatic conversion of waste cooking oils into alternative fuel--biodiesel.

PubMed

Chen, Guanyi; Ying, Ming; Li, Weizhun

2006-01-01

Production of biodiesel from pure oils through chemical conversion may not be applicable to waste oils/fats. Therefore, enzymatic conversion using immobilized lipase based on Rhizopus orzyae is considered in this article. This article studies this technological process, focusing on optimization of several process parameters, including the molar ratio of methanol to waste oils, biocatalyst load, and adding method, reaction temperature, and water content. The results indicate that methanol/oils ratio of 4, immobilized lipase/oils of 30 wt% and 40 degrees C are suitable for waste oils under 1 atm. The irreversible inactivation of the lipase is presumed and a stepwise addition of methanol to reduce inactivation of immobilized lipases is proposed. Under the optimum conditions the yield of methyl esters is around 88-90%.

Microencapsulation of fish oil by spray granulation and fluid bed film coating.

PubMed

Anwar, Sri Haryani; Weissbrodt, Jenny; Kunz, Benno

2010-08-01

The stability of microencapsulated fish oil prepared with 2 production processes, spray granulation (SG) and SG followed by film coating (SG-FC) using a fluid bed equipment, was investigated. In the 1st process, 3 types of fish oil used were based on the ratios of eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) (10/50, 33/22, and 18/12). Each type was emulsified with soluble soybean polysaccharide (SSPS) and maltodextrin to produce 25% oil powders. In the 2nd process, 15% film coating of hydroxypropyl betacyclodextrin (HPBCD) was applied to the granules from the 1st process. The powder stability against oxidation was examined by measurement of peroxide values (PV) and headspace propanal after storage at room temperature and at 3 to 4 degrees C for 6 wk. Uncoated powder containing the lowest concentration of PUFA (18/12) was found to be stable during storage at room temperature with maximum PV of 3.98 +/- 0.001 meq/kg oil. The PV increased sharply for uncoated powder with higher concentration of omega-3 (in 33/22 and 10/50 fish oils) after 3 wk storage. The PVs were in agreement with the concentration of propanal, and these 2 parameters remained constant for most of the uncoated powders stored at low temperature. Unexpectedly, the outcomes showed that the coated powders had lower stability than uncoated powders as indicated by higher initial PVs; more hydroperoxides were detected as well as increasing propanal concentration. The investigation suggests that the film-coating by HPBCD ineffectively protected fish oil as the coating process might have induced further oxidation; however, SG is a good method for producing fish oil powder and to protect it from oxidation because of the "onion skin" structure of granules produced in this process.

Evaluation of Dust Exposure among the Workers in Agricultural Industries in North-East India.

PubMed

Dewangan, Krishna N; Patil, Mahesh R

2015-11-01

This study aims to quantify dust exposure among the workers in four different industrial settings: rice mills, flour mills, oil mills, and tea factories and to compare the obtained data with the permissible exposure limit (PEL) of Indian Union Ministry of Labour as well as to compare the dust exposure across activities and seasons. RespiCon(TM) particle sampler was used for collecting dust concentration in the breathing zone of the workers. In total, 149 workers participated in the study and 204 samples were collected. Samples were collected in the vicinity of different processing operations. Samples in the rice mills were collected for two consecutive years in two seasons; however samples from other industries were collected for 1 year. The results indicate that geometric mean (GM) of dust exposure was significantly (P < 0.0001) different among industrial settings. Respirable dust were 8.22, 5.76, 2.98, and 6.34mg m(-3) and total dust exposure were 81.05, 111.02, 56.68, and 39.85mg m(-3) in the rice mills, oil mills, flour mills, and tea factories, respectively. Considerable variations in dust exposure were observed in different activities in the rice and oil mills; however variation was relatively less in the flour mills and tea factories. In the rice mills, dust concentration was higher in winter than those obtained in autumn and it is significantly different (P < 0.05) for inhalable dust and total dust. Positive correlation was obtained in thoracic dust (r (2) = 0.94) and inhalable dust (r (2) = 0.97) with total dust and thoracic dust with inhalable dust (r (2) = 0.89). The results show that majority of the workers are exposed to higher level of respirable dust as compared to the PEL, while total dust exposure to all the workers were higher than the PEL; thus, immediate reduction of dust exposure among the workers is necessary for preventing respiratory system impairment. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

40 CFR 63.2832 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production What This Subpart... operate a vegetable oil production process that is a major source of HAP emissions or is collocated within... emissions. (i) A vegetable oil production process is defined in § 63.2872. In general, it is the collection...

40 CFR 63.2832 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production What This Subpart... operate a vegetable oil production process that is a major source of HAP emissions or is collocated within... emissions. (i) A vegetable oil production process is defined in § 63.2872. In general, it is the collection...

NASA today, and a vision for tomorrow. [The NASA Administrator's Speech to the American Geophysical Union on 26 May 1994

NASA Technical Reports Server (NTRS)

Goldin, Daniel S.

1994-01-01

Under the administration of Dan Goldin's leadership, NASA is reinventing itself. In the process, the agency is also searching for a vision to define its role, both as a US Government agency and as a leading force in humanity's exploration of space. An adaption of Goldin's speech to the American Geophysical Union on 26 May 1994 in which he proposes one possible unifying vision is presented.

Recommendations from the International Union of Radioecology to improve guidance on radiation protection.

PubMed

Bréchignac, François; Bradshaw, Clare; Carroll, Simon; Jaworska, Alicja; Kapustka, Larry; Monte, Luigi; Oughton, Deborah

2011-07-01

This brief commentary summarizes the views of a working group assembled by the International Union of Radioecology to advance the approaches used to evaluate effects of radioactive materials in the environment. The key message in both the research needs and the recommendations for management of radioactive materials centers around the need to adopt an ecocentric approach that recognizes the interconnectedness of biota, including humans, and ecological processes. Copyright © 2011 SETAC.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Biodiesel, a renewable fuel produced from animal fats or vegetable oils, is popular among many vehicle owners and fleet managers seeking to reduce emissions and support U.S. energy security. Questions sometimes arise about the viability of fueling vehicles with straight vegetable oil (SVO), or waste oils from cooking and other processes, without intermediate processing. But SVO and waste oils differ from biodiesel (and conventional diesel) in some important ways and are generally not considered acceptable vehicle fuels for large-scale or long-term use.

Scattered colorimetry and multivariate data processing as an objective tool for liquid mapping (Invited Paper)

NASA Astrophysics Data System (ADS)

Mignani, A. G.; Ciaccheri, L.; Smith, P. R.; Cimato, A.; Attilio, C.; Huertas, R.; Melgosa Latorre, Manuel; Bertho, A. C.; O'Rourke, B.; McMillan, N. D.

2005-05-01

Scattered colorimetry, i.e., multi-angle and multi-wavelength absorption spectroscopy performed in the visible spectral range, was used to map three kinds of liquids: extra virgin olive oils, frying oils, and detergents in water. By multivariate processing of the spectral data, the liquids could be classified according to their intrinisic characteristics: geographic area of extra virgin olive oils, degradation of frying oils, and surfactant types and mixtures in water.

Methods of Oil Detection in Response to the Deepwater Horizon Oil Spill

EPA Science Inventory

Detecting oil in the northern Gulf of Mexico following the Deepwater Horizon oil spill presented unique challenges due to the spatial and temporal extent of the spill and the subsequent dilution of oil in the environment. Over time, physical, chemical, and biological processes a...

Rapid development of a castor cultivar with increased oil content

USDA-ARS?s Scientific Manuscript database

Castor seed oil contains 90% ricinoleic acid which has a wide range of industrial applications. Improvement in oil content would be of great benefit to castor growers and oil processers. Two cycles of phenotypic recurrent selection were conducted through screening for high oil content castor seeds u...

Oil Motion Control by an Extra Pinning Structure in Electro-Fluidic Display.

PubMed

Dou, Yingying; Tang, Biao; Groenewold, Jan; Li, Fahong; Yue, Qiao; Zhou, Rui; Li, Hui; Shui, Lingling; Henzen, Alex; Zhou, Guofu

2018-04-06

Oil motion control is the key for the optical performance of electro-fluidic displays (EFD). In this paper, we introduced an extra pinning structure (EPS) into the EFD pixel to control the oil motion inside for the first time. The pinning structure canbe fabricated together with the pixel wall by a one-step lithography process. The effect of the relative location of the EPS in pixels on the oil motion was studied by a series of optoelectronic measurements. EPS showed good control of oil rupture position. The properly located EPS effectively guided the oil contraction direction, significantly accelerated switching on process, and suppressed oil overflow, without declining in aperture ratio. An asymmetrically designed EPS off the diagonal is recommended. This study provides a novel and facile way for oil motion control within an EFD pixel in both direction and timescale.

Enumeration and rapid identification of yeasts during extraction processes of extra virgin olive oil in Tuscany.

PubMed

Mari, Eleonora; Guerrini, Simona; Granchi, Lisa; Vincenzini, Massimo

2016-06-01

The aim of this study was to evaluate the occurrence of yeast populations during different olive oil extraction processes, carried out in three consecutive years in Tuscany (Italy), by analysing crushed pastes, kneaded pastes, oil from decanter and pomaces. The results showed yeast concentrations ranging between 10(3) and 10(5) CFU/g or per mL. Seventeen dominant yeast species were identified by random amplified polymorphic DNA with primer M13 and their identification was confirmed by restriction fragments length polymorphism of ribosomal internal transcribed spacer and sequencing rRNA genes. The isolation frequencies of each species in the collected samples pointed out that the occurrence of the various yeast species in olive oil extraction process was dependent not only on the yeasts contaminating the olives but also on the yeasts colonizing the plant for oil extraction. In fact, eleven dominant yeast species were detected from the washed olives, but only three of them were also found in oil samples at significant isolation frequency. On the contrary, the most abundant species in oil samples, Yamadazyma terventina, did not occur in washed olive samples. These findings suggest a phenomenon of contamination of the plant for oil extraction that selects some yeast species that could affect the quality of olive oil.

Improved extraction of avocado oil by application of sono-physical processes.

PubMed

Martínez-Padilla, Laura Patricia; Franke, Lisa; Xu, Xin-Qing; Juliano, Pablo

2018-01-01

Ultrasound treatment is known to increase the oil extractability in olive and palm oil processes. This work examined the effect of ultrasound conditioning of avocado puree on oil extractability and quality, at low (18+40kHz) and high (2MHz) frequencies, at litre-scale. Other ultrasound parameters evaluated included high frequency effect (0.4, 0.6, and 2MHz; 5min; 90kJ/kg) and sonication time (2.5-10min at 2MHz), without malaxation. Finally, a megasonic post-malaxation intervention was assessed at selected malaxation times (15, 30, and 60min). Both low and high frequency ultrasound treatments of the non-malaxed avocado puree improved extractability by 15-24% additional oil recovery, with the highest extractability achieved after 2MHz treatments, depending on the fruit maturity and oil content. There was no preferential improvement on oil extractability observed across high frequencies, even though extractability increased with sonication time. Ultrasound treatment also showed a positive effect after puree malaxation. Oils obtained from sonicated purees showed peroxide and free fatty acid values below the industrial specification levels and an increase in total phenolic compounds after 2MHz treatment. High frequency ultrasound conditioning of avocado puree can enhance oil separation and potentially decrease the malaxation time in industrial processes without impacting on oil quality. Copyright © 2017 Elsevier B.V. All rights reserved.

Rare Earth Elements in Alberta Oil Sand Process Streams

DOE PAGES

Roth, Elliot; Bank, Tracy; Howard, Bret; ...

2017-04-05

The concentrations of rare earth elements in Alberta, Canada oil sands and six oil sand waste streams were determined using inductively coupled plasma mass spectrometry (ICP–MS). The results indicate that the rare earth elements (REEs) are largely concentrated in the tailings solvent recovery unit (TSRU) sample compared to the oil sand itself. The concentration of lanthanide elements is ~1100 mg/kg (1100 ppm or 0.11 weight %), which represents a >20× increase in the concentration compared to the oil sand itself and a >7× increase compared to the North American Shale Composite (NASC). The process water, which is used to extractmore » the oil from oil sands, and the water fraction associated with the different waste streams had very low concentrations of REEs that were near or below the detection limits of the instrument, with the highest total concentration of REEs in the water fraction being less than 10 μg/L (ppb). Size and density separations were completed, and the REEs and other potentially interesting and valuable metals, such as Ti and Zr, were concentrated in different fractions. These results give insights into the possibility of recovering REEs from waste streams generated from oil sand processing.« less

Rare Earth Elements in Alberta Oil Sand Process Streams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roth, Elliot; Bank, Tracy; Howard, Bret

The concentrations of rare earth elements in Alberta, Canada oil sands and six oil sand waste streams were determined using inductively coupled plasma mass spectrometry (ICP–MS). The results indicate that the rare earth elements (REEs) are largely concentrated in the tailings solvent recovery unit (TSRU) sample compared to the oil sand itself. The concentration of lanthanide elements is ~1100 mg/kg (1100 ppm or 0.11 weight %), which represents a >20× increase in the concentration compared to the oil sand itself and a >7× increase compared to the North American Shale Composite (NASC). The process water, which is used to extractmore » the oil from oil sands, and the water fraction associated with the different waste streams had very low concentrations of REEs that were near or below the detection limits of the instrument, with the highest total concentration of REEs in the water fraction being less than 10 μg/L (ppb). Size and density separations were completed, and the REEs and other potentially interesting and valuable metals, such as Ti and Zr, were concentrated in different fractions. These results give insights into the possibility of recovering REEs from waste streams generated from oil sand processing.« less

[Microwave thermal remediation of soil contaminated with crude oil enhanced by granular activated carbon].

PubMed

Li, Da-Wei; Zhang, Yao-Bin; Quan, Xie; Zhao, Ya-Zhi

2009-02-15

The advantage of rapid, selective and simultaneous heating of microwave heating technology was taken to remediate the crude oil-contaminated soil rapidly and to recover the oil contaminant efficiently. The contaminated soil was processed in the microwave field with addition of granular activated carbon (GAC), which was used as strong microwave absorber to enhance microwave heating of the soil mixture to remove the oil contaminant and recover it by a condensation system. The influences of some process parameters on the removal of the oil contaminant and the oil recovery in the remediation process were investigated. The results revealed that, under the condition of 10.0% GAC, 800 W microwave power, 0.08 MPa absolute pressure and 150 mL x min(-1) carrier gas (N2) flow-rate, more than 99% oil removal could be obtained within 15 min using this microwave thermal remediation enhanced by GAC; at the same time, about 91% of the oil contaminant could be recovered without significant changes in chemical composition. In addition, the experiment results showed that GAC can be reused in enhancing microwave heating of soil without changing its enhancement efficiency obviously.

Aligning food-processing policies to promote healthier fat consumption in India.

PubMed

Downs, Shauna M; Marie Thow, Anne; Ghosh-Jerath, Suparna; Leeder, Stephen R

2015-09-01

India is undergoing a shift in consumption from traditional foods to processed foods high in sugar, salt and fat. Partially hydrogenated vegetable oils (PHVOs) high in trans-fat are often used in processed foods in India given their low cost and extended shelf life. The World Health Organization has called for the elimination of PHVOs from the global food supply and recommends their replacement with polyunsaturated fat to maximize health benefits. This study examined barriers to replacing industrially produced trans-fat in the Indian food supply and systematically identified potential policy solutions to assist the government in encouraging its removal and replacement with healthier polyunsaturated fat. A combination of food supply chain analysis and semi-structured interviews with key stakeholders was conducted. The main barriers faced by the food-processing sector in terms of reducing use of trans-fat and replacing it with healthier oils in India were the low availability and high cost of oils high in polyunsaturated fats leading to a reliance on palm oil (high in saturated fat) and the low use of those healthier oils in product reformulation. Improved integration between farmers and processors, investment in technology and pricing strategies to incentivize use of healthier oils for product reformulation were identified as policy options. Food processors have trouble accessing sufficient affordable healthy oils for product reformulation, but existing incentives aimed at supporting food processing could be tweaked to ensure a greater supply of healthy oils with the potential to improve population health. © The Author (2014). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Determination of fatty acid composition and quality characteristics of oils from palm fruits using solvent extraction

NASA Astrophysics Data System (ADS)

Kasmin, Hasimah; Lazim, Azwan Mat; Awang, Roila

2015-09-01

Palm oil contains about 45% of saturated palmitic acid and 39% of mono-unsaturated oleic acid. Investigations made in the past to trace the fatty acid composition in palm revealed that ripeness of fresh fruit bunch (FFB) affect oil composition. However, there is no evidence that processing operations affect oil composition, although different stage of processing does affect the quality of oil extracted. An improved method for sterilizing the oil palm fruits by dry heating, followed by oil extraction has been studied. This method eliminates the use of water, thus, increasing the extraction of lipid soluble. The objective of this study is to determine the possibility production of palm oil with different fatty acid composition (FAC) as well as the changes in quality from conventional milling. The unripe and ripe FFB were collected, sterilized and extracted using different method of solvent extraction. Preliminary data have shown that variation in FAC will also alter the physical and chemical properties of the oil extracted.

Modeling Bottom Sediment Erosion Process by Swirling the Flow by Tangential Supply of Oil in the Tank

NASA Astrophysics Data System (ADS)

Nekrasov, V. O.

2016-10-01

The article carries out a statistical data processing of quantitative and territorial division of oil tanks operating in Tyumen region, intended for reception, storage and distribution of commercial oil through trunk pipelines. It describes the working principle of the new device of erosion and prevention of oil bottom sediment formation with tangential supply of oil pumped into reservoir. The most significant similarity criteria can be emphasized in modeling rotational flows exerting significant influence on the structure of the circulating flow of oil in tank when operation of the device described. The dependence of the distribution of the linear velocity of a point on the surface along the radius at the circular motion of the oil in the tank is characterized, and on the basis of this dependence, a formula of general kinetic energy of rotational motion of oil and asphalt-resin-paraffin deposits total volume in the oil reservoir is given.

Global volatile profile of virgin olive oils flavoured by aromatic/medicinal plants.

PubMed

Perestrelo, R; Silva, C; Silva, P; Câmara, J S

2017-07-15

The global volatile profile of commercial virgin olive oils and flavoured olive oils with aromatic/medicinal plants, was established using liquid-liquid microextraction (LLME) and headspace solid-phase microextraction (HS-SPME) combined with gas chromatography-quadrupole mass spectrometry (GC-qMS). More than 60 volatile organic compounds (VOCs belonging to different groups were identified using both methods. Olive oils volatile profile was slightly influenced by maceration process, which occurred at room temperature (20±2°C) for 15days. The predominant differences were observed in terpenoids group, since some of them were only identified in the flavoured olive oils, while others showed an increase with the maceration process. VOCs mass transfer from plants to olive oils could explain the observed results. Principal components analysis (PCA) applied to LLME/GC-qMS data allowed to distinguish the olive oils. The flavoured oils would increase the use of olive oil among consumers as consequence of the improvement of its aromatic profile and healthy properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Method for cold stable biojet fuel

DOEpatents

Seames, Wayne S.; Aulich, Ted

2015-12-08

Plant or animal oils are processed to produce a fuel that operates at very cold temperatures and is suitable as an aviation turbine fuel, a diesel fuel, a fuel blendstock, or any fuel having a low cloud point, pour point or freeze point. The process is based on the cracking of plant or animal oils or their associated esters, known as biodiesel, to generate lighter chemical compounds that have substantially lower cloud, pour, and/or freeze points than the original oil or biodiesel. Cracked oil is processed using separation steps together with analysis to collect fractions with desired low temperature properties by removing undesirable compounds that do not possess the desired temperature properties.

Petroleum mineral oil refining and evaluation of cancer hazard.

PubMed

Mackerer, Carl R; Griffis, Larry C; Grabowski, John S; Reitman, Fred A

2003-11-01

Petroleum base oils (petroleum mineral oils) are manufactured from crude oils by vacuum distillation to produce several distillates and a residual oil that are then further refined. Aromatics including alkylated polycyclic aromatic compounds (PAC) are undesirable constituents of base oils because they are deleterious to product performance and are potentially carcinogenic. In modern base oil refining, aromatics are reduced by solvent extraction, catalytic hydrotreating, or hydrocracking. Chronic exposure to poorly refined base oils has the potential to cause skin cancer. A chronic mouse dermal bioassay has been the standard test for estimating carcinogenic potential of mineral oils. The level of alkylated 3-7-ring PAC in raw streams from the vacuum tower must be greatly reduced to render the base oil noncarcinogenic. The processes that can reduce PAC levels are known, but the operating conditions for the processing units (e.g., temperature, pressure, catalyst type, residence time in the unit, unit engineering design, etc.) needed to achieve adequate PAC reduction are refinery specific. Chronic dermal bioassays provide information about whether conditions applied can make a noncarcinogenic oil, but cannot be used to monitor current production for quality control or for conducting research or developing new processes since this test takes at least 78 weeks to conduct. Three short-term, non-animal assays all involving extraction of oil with dimethylsulfoxide (DMSO) have been validated for predicting potential carcinogenic activity of petroleum base oils: a modified Ames assay of a DMSO extract, a gravimetric assay (IP 346) for wt. percent of oil extracted into DMSO, and a GC-FID assay measuring 3-7-ring PAC content in a DMSO extract of oil, expressed as percent of the oil. Extraction with DMSO concentrates PAC in a manner that mimics the extraction method used in the solvent refining of noncarcinogenic oils. The three assays are described, data demonstrating the validation of the assays are shown, and test results of currently manufactured base oils are summarized to illustrate the general lack of cancer hazard for the base oils now being manufactured.

Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils.

PubMed

Goula, Athanasia M; Ververi, Maria; Adamopoulou, Anna; Kaderides, Kyriakos

2017-01-01

The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30min. The optimum operating conditions were found to be: extraction temperature, 51.5°C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters. Copyright © 2016 Elsevier B.V. All rights reserved.

Evaluation of the antifungal effects of bio-oil prepared with lignocellulosic biomass using fast pyrolysis technology.

PubMed

Kim, Kwang Ho; Jeong, Han Seob; Kim, Jae-Young; Han, Gyu Seong; Choi, In-Gyu; Choi, Joon Weon

2012-10-01

This study was performed to investigate the utility of bio-oil, produced via a fast pyrolysis process, as an antifungal agent against wood-rot fungi. Bio-oil solutions (25-100 wt.%) were prepared by diluting the bio-oil with EtOH. Wood block samples (yellow poplar and pitch pine) were treated with diluted bio-oil solutions and then subjected to a leaching process under hot water (70°C) for 72 h. After the wood block samples were thoroughly dried, they were subjected to a soil block test using Tyromyces palustris and Trametes versicolor. The antifungal effect of the 75% and 100% bio-oil solutions was the highest for both wood blocks. Scanning electron microscopy analysis indicated that some chemical components in the bio-oil solution could agglomerate together to form clusters in the inner part of the wood during the drying process, which could act as a wood preservative against fungal growth. According to GC/MS analysis, the components of the agglomerate were mainly phenolic compounds derived from lignin polymers. Copyright © 2012 Elsevier Ltd. All rights reserved.

Succession of microbial communities and changes of incremental oil in a post-polymer flooded reservoir with nutrient stimulation.

PubMed

Gao, Peike; Li, Guoqiang; Le, Jianjun; Liu, Xiaobo; Liu, Fang; Ma, Ting

2018-02-01

Further exploitation of the residual oil underground in post-polymer flooded reservoirs is attractive and challengeable. In this study, indigenous microbial enhanced oil recovery (IMEOR) in a post-polymer flooded reservoir was performed. The succession of microbial communities was revealed by high-throughput sequencing of 16S rRNA genes and changes of incremental oil were analyzed. The results indicated that the abundances of reservoir microorganisms significantly increased, with alpha diversities decreased in the IMEOR process. With the intermittent nutrient injection, microbial communities showed a regular change and were alternately dominated by minority populations: Pseudomonas and Acinetobacter significantly increased when nutrients were injected; Thauera, Azovibrio, Arcobacter, Helicobacter, Desulfitobacterium, and Clostridium increased in the following water-flooding process. Accompanied by the stimulated populations, higher oil production was obtained. However, these populations did not contribute a persistent level of incremental oil in the reservoir. In summary, this study revealed the alternative succession of microbial communities and the changes of incremental oil in a post-polymer flooded reservoir with intermittent nutrient stimulation process.

An effective ostrich oil bleaching technique using peroxide value as an indicator.

PubMed

Palanisamy, Uma Devi; Sivanathan, Muniswaran; Radhakrishnan, Ammu Kutty; Haleagrahara, Nagaraja; Subramaniam, Thavamanithevi; Chiew, Gan Seng

2011-07-05

Ostrich oil has been used extensively in the cosmetic and pharmaceutical industries. However, rancidity causes undesirable chemical changes in flavour, colour, odour and nutritional value. Bleaching is an important process in refining ostrich oil. Bleaching refers to the removal of certain minor constituents (colour pigments, free fatty acid, peroxides, odour and non-fatty materials) from crude fats and oils to yield purified glycerides. There is a need to optimize the bleaching process of crude ostrich oil prior to its use for therapeutic purposes. The objective of our study was to establish an effective method to bleach ostrich oil using peroxide value as an indicator of refinement. In our study, we showed that natural earth clay was better than bentonite and acid-activated clay to bleach ostrich oil. It was also found that 1 hour incubation at a 150 °C was suitable to lower peroxide value by 90%. In addition, the nitrogen trap technique in the bleaching process was as effective as the continuous nitrogen flow technique and as such would be the recommended technique due to its cost effectiveness.

The influence of purge times on the yields of essential oil components extracted from plants by pressurized liquid extraction.

PubMed

Wianowska, Dorota

2014-01-01

The influence of different purge times on the yield of the main essential oil constituents of rosemary (Rosmarinus officinalis L.), thyme (Thymus vulgaris L.), and chamomile (Chamomilla recutita L.) was investigated. The pressurized liquid extraction process was performed by applying different extraction temperatures and solvents. The results presented in the paper show that the estimated yield of essential oil components extracted from the plants in the pressurized liquid extraction process is purge time-dependent. The differences in the estimated yields are mainly connected with the evaporation of individual essential oil components and the applied solvent during the purge; the more volatile an essential oil constituent is, the greater is its loss during purge time, and the faster the evaporation of the solvent during the purge process is, the higher the concentration of less volatile essential oil components in the pressurized liquid extraction receptacle. The effect of purge time on the estimated yield of individual essential oil constituents is additionally differentiated by the extraction temperature and the extraction ability of the applied solvent.

Development of three stable isotope dilution assays for the quantitation of (E)-2-butenal (crotonaldehyde) in heat-processed edible fats and oils as well as in food.

PubMed

Granvogl, Michael

2014-02-12

Three stable isotope dilution assays (SIDAs) were developed for the quantitation of (E)-2-butenal (crotonaldehyde) in heat-processed edible fats and oils as well as in food using synthesized [¹³C₄]-crotonaldehyde as internal standard. First, a direct headspace GC-MS method, followed by two indirect methods on the basis of derivatization with either pentafluorophenylhydrazine (GC-MS) or 2,4-dinitrophenylhydrazine (LC-MS/MS), was developed. All methods are also suitable for the quantitation of acrolein using the standard [¹³C₃]-acrolein. Applying these three methods on five different types of fats and oils varying in their fatty acid compositions revealed significantly varying crotonaldehyde concentrations for the different samples, but nearly identical quantitative data for all methods. Formed amounts of crotonaldehyde were dependent not only on the type of oil, e.g., 0.29-0.32 mg/kg of coconut oil or 33.9-34.4 mg/kg of linseed oil after heat-processing for 24 h at 180 °C, but also on the applied temperature and time. The results indicated that the concentration of formed crotonaldehyde seemed to be correlated with the amount of linolenic acid in the oils. Furthermore, the formation of crotonaldehyde was compared to that of its homologue acrolein, demonstrating that acrolein was always present in higher amounts in heat-processed oils, e.g., 12.3 mg of crotonaldehyde/kg of rapeseed oil in comparison to 23.4 mg of acrolein/kg after 24 h at 180 °C. Finally, crotonaldehyde was also quantitated in fried food, revealing concentrations from 12 to 25 μg/kg for potato chips and from 8 to 19 μg/kg for donuts, depending on the oil used.

Fish protein hydrolysates: application in deep-fried food and food safety analysis.

PubMed

He, Shan; Franco, Christopher; Zhang, Wei

2015-01-01

Four different processes (enzymatic, microwave-intensified enzymatic, chemical, and microwave-intensified chemical) were used to produce fish protein hydrolysates (FPH) from Yellowtail Kingfish for food applications. In this study, the production yield and oil-binding capacity of FPH produced from different processes were evaluated. Microwave intensification significantly increased the production yields of enzymatic process from 42% to 63%. It also increased the production yields of chemical process from 87% to 98%. The chemical process and microwave-intensified chemical process produced the FPH with low oil-binding capacity (8.66 g oil/g FPH and 6.25 g oil/g FPH), whereas the microwave-intensified enzymatic process produced FPH with the highest oil-binding capacity (16.4 g oil/g FPH). The FPH from the 4 processes were applied in the formulation of deep-fried battered fish and deep-fried fish cakes. The fat uptake of deep-fried battered fish can be reduced significantly from about 7% to about 4.5% by replacing 1% (w/w) batter powder with FPH, and the fat uptake of deep-fried fish cakes can be significantly reduced from about 11% to about 1% by replacing 1% (w/w) fish mince with FPH. Food safety tests of the FPH produced by these processes demonstrated that the maximum proportion of FPH that can be safely used in food formulation is 10%, due to its high content of histamine. This study demonstrates the value of FPH to the food industry and bridges the theoretical studies with the commercial applications of FPH. © 2015 Institute of Food Technologists®

Process for recovering products from oil shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobs, H.R.; Udell, K.S.

A process is claimed for recovering hydrocarbon products from a body of fragmented or rubblized oil shale. The process includes initiating a combustion zone adjacent the lower end of a body of oil shale and using the thermal energy therefrom for volatilizing the shale oil from the oil shale above the combustion front. Improved recovery of hydrocarbon products is realized by refluxing the heavier fractions in the volatilized shale oil. The heavier fractions are refluxed by condensing the heavier fractions and allowing the resulting condensate to flow downwardly toward the combustion front. Thermal energy from the combustion zone cracks themore » condensate producing additional lower molecular weight fractions and a carbonaceous residue. The carbonaceous residue is burned in the combustion front to supply the thermal energy. The temperature of the combustion front is maintained by regulating input of oxygen to the combustion zone. The process also includes sweeping the volatilized products from the rubblized oil shale with a noncombustible gas. The flow rate of sweep gas is also controlled to regulate the temperature of the combustion front. The recovered products can be enriched with hydrogen by using water vapor as part of the noncombustible sweep gas and cracking the water vapor with the hot carbon in the combustion front to produce hydrogen and an oxide of carbon.« less

Subsurface brine injection: Proactive approach to close the produced water loop in the western desert of Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farid, E.E.; Nour, M.H.

1996-11-01

In 1988 a major onshore production facility was producing oil from eight formations in six oil fields located in the western desert of Egypt. Two of these formations include active water drive reservoirs, in addition; three reservoirs at that date were receiving water injection to enhance oil recovery. To handle the increasing volumes of the produced water (which is contaminated with oil, production chemicals and other pollutants), three alternatives were investigated: (1) Injection into disposal wells. (2) Dumping in surface disposal pits. (3) Re-injection to waterflood some oil reservoirs. The investigation revealed that the first two options are technically unfavorable,more » also they are conventional Waste Management Technologies (WMT) which provide short-term remedial solution. In contrast, Produced Water Re-Injection (PWRI) is an Environmental Control Technology (ECT) which minimize the environmental impact through process improvements. A state -of-the-art re-injection process was utilized using chemical treatment, gas liberation, settling, filtration and injection. This process represents a combination of two (ECT) methods: Reuse (for water flooding) and Recycling (when brine is redisposed underground). This process reduce the overall volumes of produced water to be disposed, increase the oil reserves, reservoir pressure and oil production and converse the underground water reserve.« less

Processes of inclusion and adverse incorporation: oil palm and agrarian change in Sumatra, Indonesia.

PubMed

McCarthy, John

2010-01-01

Changes in globalised agriculture raise critical questions as rapid agricultural development leads to widespread social and environmental transformation. With increased global demand for vegetable oils and biofuel, in Indonesia the area under oil palm has doubled over the last decade. This paper presents a case study of how micro-processes that are linked to wider dynamics shape oil palm related agrarian change in villages in Sumatra, Indonesia. It pursues related questions regarding the impact of agribusiness-driven agriculture, the fate of smallholders experiencing contemporary agrarian transition, and the impact of increased demand for vegetable oils and biofuels on agrarian structures in Sumatra. It argues that the paths of agrarian change are highly uneven and depend on how changing livelihood strategies are enabled or constrained by economic, social and political relations that vary over time and space. In contrast to simplifying narratives of inclusion/exclusion, it argues that outcomes depend on the terms under which smallholders engage with oil palm. Distinguishing between exogenous processes of agribusiness expansion and endogenous commodity market expansion, it finds each is associated with characteristic processes of change. It concludes that the way successive policy interventions have worked with the specific characteristics of oil palm have cumulatively shaped the space where agrarian change occurs in Sumatra.

Liquefaction of lignocellulosic biomass: solvent, process parameter, and recycle oil screening.

PubMed

van Rossum, Guus; Zhao, Wei; Castellvi Barnes, Maria; Lange, Jean-Paul; Kersten, Sascha R A

2014-01-01

The liquefaction of lignocellulosic biomass is studied for the production of liquid (transportation) fuels. The process concept uses a product recycle as a liquefaction medium and produces a bio-oil that can be co-processed in a conventional oil refinery. This all is done at medium temperature (≈ 300 °C) and pressure (≈ 60 bar). Solvent-screening experiments showed that oxygenated solvents are preferred as they allow high oil (up to 93% on carbon basis) and low solid yields (≈ 1-2% on carbon basis) and thereby outperform the liquefaction of biomass in compressed water and biomass pyrolysis. The following solvent ranking was obtained: guaiacol>hexanoic acid ≫ n-undecane. The use of wet biomass results in higher oil yields than dry biomass. However, it also results in a higher operating pressure, which would make the process more expensive. Refill experiments were also performed to evaluate the possibility to recycle the oil as the liquefaction medium. The recycled oil appeared to be very effective to liquefy the biomass and even surpassed the start-up solvent guaiacol, but became increasingly heavy and more viscous after each refill and eventually showed a molecular weight distribution that resembles that of refinery vacuum residue. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A new LDMI decomposition approach to explain emission development in the EU: individual and set contribution.

PubMed

Madaleno, Mara; Moutinho, Victor

2017-04-01

This study breaks down carbon emissions into six effects within the current 28 European Union (EU) countries group, thereafter, they are divided into two different groups (the first 15 countries (EU-15) and the last 13 entering the EU (EU13)). Country-specific highlights are also examined. It analyses the evolution of the effects using a data span that runs from 1990 to 2014, to determine which of them had more impact on the intensity of emissions, while also breaking down the complete period into two distinct periods (before the Kyoto protocol (1990-2004) and after Kyoto (2005-2014)). In order to add more knowledge to the current literature, both the additive and multiplicative decomposition techniques were used to examine carbon dioxide (CO 2 ) emissions and the selected six components: carbon intensity, fossil fuel consumption, energy intensity, oil imports intensity, oil dependence, and population effect. Results point to different adapting velocities for Kyoto targets and necessary compromises. The different velocities were translated into different positive and negative impacts in the change of behavior of CO 2 emissions throughout Europe. A stress in the fluctuations in CO 2 variations before and after Kyoto and between the two different groups of EU countries could be noticed. Moreover, energy intensity and per capita dependence of oil products were identified as the major responsible components for the total and negative changes of emissions in recent years. A decrease in total changes of emissions is observed due to the fossil fuel energy consumption effect and total petroleum products effects. It is possible to infer from here that increased renewable capacity is contributing in a positive way to eco-efficiency, and should therefore be accounted for in national policymakers' decisions in the strongest way possible. Results also seem to indicate that per capita dependence of oil products has decreased, despite oil imports intensity constancy and increased renewable capacity, however, with clear heterogeneous effects, worthy of consideration when defining policies.

Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karnofsky, G. B.

1980-12-16

A process for solvent extraction of oil from oil bearing diatomite ore and an apparatus for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent, solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom, and solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure.

The Importance of Ammonia for Winter Haze Formation in Two Oil and Gas Production Regions

NASA Astrophysics Data System (ADS)

Collett, J. L., Jr.; Li, Y.; Evanoski-Cole, A. R.; Sullivan, A.; Day, D.; Archuleta, C.; Tigges, M.; Sewell, H. J.; Prenni, A. J.; Schichtel, B. A.

2014-12-01

Fine particle ammonium nitrate formation results from the atmospheric reaction of gaseous ammonia and nitric acid. This reaction is most important in winter when low temperatures thermodynamically enhance particle formation. Nitrogen oxides emissions from oil and gas operations partially react in the atmosphere to form nitric acid. The availability of atmospheric ammonia plays an important role in determining whether the nitric acid formed results in wintertime ammonium nitrate formation. Here we contrast situations in two important U.S. oil and gas production regions. Measurements of ammonia, nitric acid, ammonium nitrate and other species were made from 2007 to present near Boulder, Wyoming and in winters 2013 and 2014 in western North Dakota. The Boulder, Wyoming site is close to the large Jonah and Pinedale Anticline gas fields. Field sites at the north unit of Theodore Roosevelt National Park and Fort Union are situated in the large Bakken Formation oil and gas production region. Wintertime formation of nitric acid and ammonium nitrate, together comprising nitrogen in the +5 oxidation state (N(V)), was observed in both locations. Concentrations of N(V), however, are generally much lower at Boulder, WY than in the Bakken. An even bigger difference is seen in fine particle ammonium nitrate concentrations; limited regional ammonia is available in western Wyoming to react with nitric acid, leaving a portion of the nitric acid trapped in the gas phase. Higher concentrations of ammonia are observed in the Bakken where they support formation of much higher concentrations of ammonium nitrate. Comparison of these two regions clearly indicates the importance of understanding both local NOx emissions and regional concentrations of ammonia in predicting source impacts on formation of fine particles and haze.

16 CFR 802.3 - Acquisitions of carbon-based mineral reserves.

Code of Federal Regulations, 2014 CFR

2014-01-01

... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands together with... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands and associated... pipeline and pipeline system or processing facility which transports or processes oil and gas after it...

16 CFR 802.3 - Acquisitions of carbon-based mineral reserves.

Code of Federal Regulations, 2010 CFR

2010-01-01

... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands together with... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands and associated... pipeline and pipeline system or processing facility which transports or processes oil and gas after it...

16 CFR 802.3 - Acquisitions of carbon-based mineral reserves.

Code of Federal Regulations, 2013 CFR

2013-01-01

... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands together with... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands and associated... pipeline and pipeline system or processing facility which transports or processes oil and gas after it...

16 CFR 802.3 - Acquisitions of carbon-based mineral reserves.

Code of Federal Regulations, 2012 CFR

2012-01-01

... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands together with... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands and associated... pipeline and pipeline system or processing facility which transports or processes oil and gas after it...

16 CFR 802.3 - Acquisitions of carbon-based mineral reserves.

Code of Federal Regulations, 2011 CFR

2011-01-01

... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands together with... gas, shale or tar sands, or rights to reserves of oil, natural gas, shale or tar sands and associated... pipeline and pipeline system or processing facility which transports or processes oil and gas after it...

Biodiesel production from heterotrophic microalgal oil.

PubMed

Miao, Xiaoling; Wu, Qingyu

2006-04-01

The present study introduced an integrated method for the production of biodiesel from microalgal oil. Heterotrophic growth of Chlorella protothecoides resulted in the accumulation of high lipid content (55%) in cells. Large amount of microalgal oil was efficiently extracted from these heterotrophic cells by using n-hexane. Biodiesel comparable to conventional diesel was obtained from heterotrophic microalgal oil by acidic transesterification. The best process combination was 100% catalyst quantity (based on oil weight) with 56:1 molar ratio of methanol to oil at temperature of 30 degrees C, which reduced product specific gravity from an initial value of 0.912 to a final value of 0.8637 in about 4h of reaction time. The results suggested that the new process, which combined bioengineering and transesterification, was a feasible and effective method for the production of high quality biodiesel from microalgal oil.

Numerical simulation of the SAGD process coupled with geomechanical behavior

NASA Astrophysics Data System (ADS)

Li, Pingke

Canada has vast oil sand resources. While a large portion of this resource can be recovered by surface mining techniques, a majority is located at depths requiring the application of in situ recovery technologies. Although a number of in situ recovery technologies exist, the steam assisted gravity drainage (SAGD) process has emerged as one of the most promising technologies to develop the in situ oil sands resources. During the SAGD operations, saturated steam is continuously injected into the oil sands reservoir, which induces pore pressure and stress variations. As a result, reservoir parameters and processes may also vary, particularly when tensile and shear failure occur. This geomechanical effect is obvious for oil sands material because oil sands have the in situ interlocked fabric. The conventional reservoir simulation generally does not take this coupled mechanism into consideration. Therefore, this research is to improve the reservoir simulation techniques of the SAGD process applied in the development of oil sands and heavy oil reservoirs. The analyses of the decoupled reservoir geomechanical simulation results show that the geomechanical behavior in SAGD has obvious impact on reservoir parameters, such as absolute permeability. The issues with the coupled reservoir geomechanical simulations of the SAGD process have been clarified and the permeability variations due to geomechanical behaviors in the SAGD process investigated. A methodology of sequentially coupled reservoir geomechanical simulation technique was developed based on the reservoir simulator, EXOTHERM, and the geomechanical simulator, FLAC. In addition, a representative geomechanical model of oil sands material was summarized in this research. Finally, this reservoir geomechanical simulation methodology was verified with the UTF Phase A SAGD project and applied in a SAGD operation with gas-over-bitumen geometry. Based on this methodology, the geomechanical effect on the SAGD production performance can be quantified. This research program involves the analyses of laboratory testing results obtained from literatures. However, no laboratory testing was conducted in the process of this research.

Antimicrobial activity of clove and rosemary essential oils alone and in combination.

PubMed

Fu, Yujie; Zu, Yuangang; Chen, Liyan; Shi, Xiaoguang; Wang, Zhe; Sun, Su; Efferth, Thomas

2007-10-01

In the present study, the antimicrobial activity of the essential oils from clove (Syzygium aromaticum (L.) Merr. et Perry) and rosemary (Rosmarinus officinalis L.) was tested alone and in combination. The compositions of the oils were analysed by GC/MS. Minimum inhibitory concentrations (MIC) against three Gram-positive bacteria, three Gram-negative bacteria and two fungi were determined for the essential oils and their mixtures. Furthermore, time-kill dynamic processes of clove and rosemary essential oils against Staphylococcus epidermidis, Escherichia coli and Candida albicans were tested. Both essential oils possessed significant antimicrobial effects against all microorganisms tested. The MICs of clove oil ranged from 0.062% to 0.500% (v/v), while the MICs of rosemary oil ranged from 0.125% to 1.000% (v/v). The antimicrobial activity of combinations of the two essential oils indicated their additive, synergistic or antagonistic effects against individual microorganism tests. The time-kill curves of clove and rosemary essential oils towards three strains showed clearly bactericidal and fungicidal processes of (1)/(2) x MIC, MIC, MBC and 2 x MIC.

Decontamination of uranium-contaminated waste oil using supercritical fluid and nitric acid.

PubMed

Sung, Jinhyun; Kim, Jungsoo; Lee, Youngbae; Seol, Jeunggun; Ryu, Jaebong; Park, Kwangheon

2011-07-01

The waste oil used in nuclear fuel processing is contaminated with uranium because of its contact with materials or environments containing uranium. Under current law, waste oil that has been contaminated with uranium is very difficult to dispose of at a radioactive waste disposal site. To dispose of the uranium-contaminated waste oil, the uranium was separated from the contaminated waste oil. Supercritical R-22 is an excellent solvent for extracting clean oil from uranium-contaminated waste oil. The critical temperature of R-22 is 96.15 °C and the critical pressure is 49.9 bar. In this study, a process to remove uranium from the uranium-contaminated waste oil using supercritical R-22 was developed. The waste oil has a small amount of additives containing N, S or P, such as amines, dithiocarbamates and dialkyldithiophosphates. It seems that these organic additives form uranium-combined compounds. For this reason, dissolution of uranium from the uranium-combined compounds using nitric acid was needed. The efficiency of the removal of uranium from the uranium-contaminated waste oil using supercritical R-22 extraction and nitric acid treatment was determined.

A review on applications of nanotechnology in the enhanced oil recovery part A: effects of nanoparticles on interfacial tension

NASA Astrophysics Data System (ADS)

Cheraghian, Goshtasp; Hendraningrat, Luky

2016-01-01

Chemical enhanced oil recovery is another strong growing technology with the potential of a step change innovation, which will help to secure future oil supply by turning resources into reserves. While Substantial amount of crude oil remains in the reservoir after primary and secondary production, conventional production methods give access to on average only one-third of original oil in place, the use of surfactants and polymers allows for recovery of up to another third of this oil. Chemical flooding is of increasing interest and importance due to high oil prices and the need to increase oil production. Research in nanotechnology in the petroleum industry is advancing rapidly and an enormous progress in the application of nanotechnology in this area is to be expected. Nanotechnology has the potential to profoundly change enhanced oil recovery and to improve mechanism of recovery. This paper, therefore, focuses on the reviews of the application of nano technology in chemical flooding process in oil recovery and reviews the application nano in the polymer and surfactant flooding on the interfacial tension process.

Nutritionally enriched 1,3-diacylglycerol-rich oil: Low calorie fat with hypolipidemic effects in rats.

PubMed

Prabhavathi Devi, B L A; Gangadhar, K N; Prasad, R B N; Sugasini, D; Rao, Y Poorna Chandra; Lokesh, B R

2018-05-15

An enzymatic process was developed for the preparation of a nutritionally enriched 1,3-diacylglycerol(DAG)-rich oil from a blend of refined sunflower and rice bran oils. The process involves hydrolysis of vegetable oil blend using Candida cylindracea followed by esterification with glycerol using Lipozyme RM1M. The resultant DAG-rich oil contains 84% of DAG (66% of 1,3-DAG, 18% of 1,2-DAG) and 16% of triacylglycerol (TAG) along with micro nutrients like γ-oryzanol, tocotrienols, tocopherols and phytosterols. Nutritional studies of the DAG-rich oil were conducted in Wistar rats and compared with sunflower oil (SFO). The calorific value of the DAG-rich oil was estimated to be 6.45 Kcals/g as against 9.25 Kcals/g for SFO. The serum and liver cholesterol and TAG levels in rats fed with 1,3-DAG-rich oil were found to be significantly reduced as compared to rats fed diet containing SFO. We conclude that 1,3-DAG-rich oil is a low calorie fat and exhibits hypolipidemic effects. Copyright © 2017 Elsevier Ltd. All rights reserved.

Getting Over the Barrel- Achieving Independence from Foreign Oil in 2018

DTIC Science & Technology

2009-02-03

material called kerogen. Kerogen can be converted into oil via heating in the chemical process of pyrolysis .44 Depending on the richness of oil shale, it...vegetable oil, animal fat, corn , soybeans, jatropha seed oil, palm oil, switch grass and even algae. Biofuel production techniques and technologies...vary widely based on the input source – sugar-based, starch-based or oil-based. This document only examines corn -based ethanol production. The other

Food additives used in meat processing according to the Polish and European Union legislation.

PubMed

Uradziński, J; Weiner, M

2003-01-01

This paper presents the legal regulations related to the use of food additives in meat production in Poland and the European Union. The Polish legal definition of food additives is given as well as the classification of permitted food additives added to food and stimulants by their technological function. In addition, a definition of processing aids in the food industry is included. It shows that Polish legislation includes food additives used to ensure or improve food nutritional value, whereas in the EU legislation, these substances are not included in the list of food additives. Moreover, the Council Directives include food additive specific purity criteria, whereas the Polish regulations do not mention the legal regulations of this issue in practice. The European Union use mechanisms and procedures for the introduction of new food additives into internal markets as well as controlling the circulation of additives. The Polish legislation in practice, however, does not determine approval or methods for the introduction of new food additives to the market. Legal regulations on the monitoring of food additives no exist.

Flotation of oil-agglomerated coal for ash and pyrite removal -- Simultaneous grinding and agglomeration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, S.; Perkson, A.; Trass, O.

1996-12-31

Oil agglomeration is an excellent technique for the beneficiation of fine coal. For separation of the spherical agglomerates by screening, a high level of oil must be used, however. When the subsequent separation is done by flotation, this disadvantage is eliminated. Better pyrite removal is also possible. In this paper, such a fine coal beneficiation process, also called hydrophobic flocculation-flotation (HFF), is described. It features low non-polar oil consumption, intensive mechanical energy input, and smaller agglomerates or looser flocs. This process can be simplified by grinding the coal in water with small amounts of oil added. The excess grinding energymore » is then used for agglomerating the coal. The Prince coal from Nova Scotia contained 13.3% ash and 3.3% total sulfur, 1.4% pyritic. After four stages of flotation, ash and pyrite removal were 93% and 66% respectively, with 87% combustibles recovery. The parameters affecting the HFF process, such as particle size, dosage of non-polar oil, pH value of the slurry and duration of agitation, were investigated. Simultaneous grinding and agglomeration (SGA) utilizing the Szego Mill was also explored at the very low oil levels used. The intensive agitation/preconditioning step prior to flotation was eliminated. When the other parameters established from the sequential process were used with the SGA process, virtually identical beneficiation results were obtained, but with slightly lower combustibles recovery. While further testing is required to properly optimize the SGA process conditions, significant equipment simplification and energy savings are possible.« less

Economic feasibility of biochemical processes for the upgrading of crudes and the removal of sulfur, nitrogen, and trace metals from crude oil -- Benchmark cost establishment of biochemical processes on the basis of conventional downstream technologies. Final report FY95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Premuzic, E.T.

1996-08-01

During the past several years, a considerable amount of work has been carried out showing that microbially enhanced oil recovery (MEOR) is promising and the resulting biotechnology may be deliverable. At Brookhaven National Laboratory (BNL), systematic studies have been conducted which dealt with the effects of thermophilic and thermoadapted bacteria on the chemical and physical properties of selected types of crude oils at elevated temperatures and pressures. Current studies indicate that during the biotreatment several chemical and physical properties of crude oils are affected. The oils are (1) emulsified; (2) acidified; (3) there is a qualitative and quantitative change inmore » light and heavy fractions of the crudes; (4) there are chemical changes in fractions containing sulfur compounds; (5) there is an apparent reduction in the concentration of trace metals; and (6) the qualitative and quantitative changes appear to be microbial species dependent; and (7) there is a distinction between biodegraded and biotreated oils. The downstream biotechnological crude oil processing research performed thus far is of laboratory scale and has focused on demonstrating the technical feasibility of downstream processing with different types of biocatalysts under a variety of processing conditions. Quantitative economic analysis is the topic of the present project which investigates the economic feasibility of the various biochemical downstream processes which hold promise in upgrading of heavy crudes, such as those found in California, e.g., Monterey-type, Midway Sunset, Honda crudes, and others.« less

Upgrading biomass pyrolysis bio-oil to renewable fuels.

DOT National Transportation Integrated Search

2015-01-01

Fast pyrolysis is a process that can convert woody biomass to a crude bio-oil (pyrolysis oil). However, some of these compounds : contribute to bio-oil shelf life instability and difficulty in refining. Catalytic hydrodeoxygenation (HDO) of the bio-o...

Oral surgery in the European Union: challenges of diversity in training and practice.

PubMed

Nasseripour, M N; Hervé, C; Meningaud, J-P

2017-02-01

At the crossroads of medicine and dentistry, oral surgery with orthodontics are the only recognised dental specialties by the European Union. The goal of our study is to evaluate the current state of oral surgery in Europe from its teaching to its practice, the hypothesis being that a notable diversity persists despite European Union harmonisation process. To understand the impact of this diversity applied to European Union freedom of movement and its ethical implications for the practice of oral surgery, English and French questionnaires were sent by email to universities and organisations delivering authorisation to practise in France, Germany, Spain, Sweden and United Kingdom chosen based upon inclusion and exclusion criteria. An analysis of documents on these organisations' official websites was also conducted. Demographic information was obtained from the aforementioned organisations. The profile of practising oral surgeons is different dependent on the country. The university and hospital trainings conform to European recommendations and span 3-4 years. European Board certification is not required. Continuing education is mandatory only in France, Germany and United Kingdom. As for curricula and scope of practice, no consensus can be derived. There is potential conflict of interest between European Union principles of freedom of movement and protection of all citizens, as member countries do not uniformly apply Directives and recommendations. A new survey of all European Union oral surgery programmes as well as organisations delivering authorisation to practise is necessary to implement across the board harmonisation of training and practice to insure patient safety in light of the migration of European Union practitioners. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Understanding the Evolution of an Oceanic Intraplate Volcano From Seismic Reflection Data: A New Model for La Réunion, Indian Ocean

NASA Astrophysics Data System (ADS)

Lebas, E.; Le Friant, A.; Deplus, C.; de Voogd, B.

2018-02-01

High-resolution seismic reflection profiles gathered in 2006 on La Réunion submarine flanks and surrounding abyssal plain, enabled characterization of the seismostratigraphy architecture of the volcaniclastic apron. Four seismic units are defined beyond the edifice base: (1) a basal unit, interpreted as pelagic sediment predating La Réunion volcanism; (2) a second unit showing low- to medium-amplitude reflections, related to La Réunion emergence including the submarine explosive phase; (3) a high-amplitude seismic unit, associated with subaerial volcanic activity (i.e., mature island stage); and (4) an acoustically transparent unit, ascribed to erosion that currently affects the volcanic complex. Two prominent horizons delineate the base of the units II and III marking, respectively, the onset of La Réunion seamount explosive activity and the Piton des Neiges volcanic activity. Related isopach maps demonstrate: (1) the existence of a large proto-Piton des Neiges volcano during the first building phase of the volcanic complex, and (2) the central role of the Piton des Neiges volcano during the second phase. Shield growth stage of the Piton de la Fournaise volcano is also captured in the upper part of the volcaniclastic apron, attesting to its recent contribution. Seismic facies identified in the apron highlight a prevalence of sedimentary and reworking processes since the onset of the volcanism compared to catastrophic flank collapses. We present here a new model of evolution for La Réunion volcanic complex since the onset of the volcanism and argue that a major proto Piton des Neiges-Piton des Neiges volcanic complex controls La Réunion present-day morphology.

Shape change in the atlas with congenital midline non-union of its posterior arch: a morphometric geometric study.

PubMed

Ríos, Luis; Palancar, Carlos; Pastor, Francisco; Llidó, Susana; Sanchís-Gimeno, Juan Alberto; Bastir, Markus

2017-10-01

The congenital midline non-union of the posterior arch of the atlas is a developmental variant present at a frequency ranging from 0.7% to 3.9%. Most of the reported cases correspond to incidental findings during routine medical examination. In cases of posterior non-union, hypertrophy of the anterior arch and cortical bone thickening of the posterior arches have been observed and interpreted as adaptive responses of the atlas to increased mechanical stress. We sought to determine if the congenital non-union of the posterior arch results in a change in the shape of the atlas. This study is an analysis of the first cervical vertebrae from osteological collections through morphometric geometric techniques. A total of 21 vertebrae were scanned with a high-resolution three-dimensional scanner (Artec Space Spider, Artec Group, Luxembourg). To capture vertebral shape, 19 landmarks and 100 semilandmarks were placed on the vertebrae. Procrustes superimposition was applied to obtain size and shape data (MorphoJ 1.02; Klingenberg, 2011), which were analyzed through principal component analysis (PCA) and mean shape comparisons. The PCA resulted in two components explaining 22.32% and 18.8% of the total shape variance. The graphic plotting of both components indicates a clear shape difference between the control atlas and the atlas with posterior non-union. This observation was supported by statistically significant differences in mean shape comparisons between both types of vertebra (p<.0001). Changes in shape were observed in the superior and inferior articular facets, the transverse processes, and the neural canal between the control and non-union vertebrae. Non-union of the posterior arch of the atlas is associated with significant changes in the shape of the vertebra. Copyright © 2017 Elsevier Inc. All rights reserved.

Biochemically enhanced oil recovery and oil treatment

DOEpatents

Premuzic, Eugene T.; Lin, Mow

1994-01-01

This invention relates to the preparation of new, modified organisms, through challenge growth processes, that are viable in the extreme temperature, pressure and pH conditions and salt concentrations of an oil reservoir and that are suitable for use in microbial enhanced oil recovery. The modified microorganisms of the present invention are used to enhance oil recovery and remove sulfur compounds and metals from the crude oil.

Corrosion of stainless steels in the riser during co-processing of bio-oils in a fluid catalytic cracking pilot plant

DOE PAGES

Brady, M. P.; Keiser, J. R.; Leonard, D. N.; ...

2017-01-31

Co-processing of bio-oils with conventional petroleum-based feedstocks is an attractive initial option to make use of renewable biomass as a fuel source while leveraging existing refinery infrastructures. But, bio-oils and their processing intermediates have high concentrations of organic oxygenates, which, among their other negative qualities, can result in increased corrosion issues. A range of stainless steel alloys (409, 410, 304L, 316L, 317L, and 201) was exposed at the base of the riser in a fluid catalytic cracking pilot plant while co-processing vacuum gas oil with pine-derived pyrolysis bio-oils that had been catalytically hydrodeoxygenated to ~ 2 to 28% oxygen. Wemore » studied the processing using a catalyst temperature of 704 °C, a reaction exit temperature of 520 °C, and total co-processing run times of 57–75 h. External oxide scaling 5–30 μm thick and internal attack 1–5 μm deep were observed in these short-duration exposures. The greatest extent of internal attack was observed for co-processing with the least stabilized bio-oil, and more so for types 409, 410, 304L, 316L, 317L stainless steel than for type 201. Finally, the internal attack involved porous Cr-rich oxide formation, associated with local Ni-metal enrichment and S-rich nanoparticles, primarily containing Cr or Mn. Implications for alloy selection and corrosion are discussed.« less

Corrosion of stainless steels in the riser during co-processing of bio-oils in a fluid catalytic cracking pilot plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brady, M. P.; Keiser, J. R.; Leonard, D. N.

Co-processing of bio-oils with conventional petroleum-based feedstocks is an attractive initial option to make use of renewable biomass as a fuel source while leveraging existing refinery infrastructures. But, bio-oils and their processing intermediates have high concentrations of organic oxygenates, which, among their other negative qualities, can result in increased corrosion issues. A range of stainless steel alloys (409, 410, 304L, 316L, 317L, and 201) was exposed at the base of the riser in a fluid catalytic cracking pilot plant while co-processing vacuum gas oil with pine-derived pyrolysis bio-oils that had been catalytically hydrodeoxygenated to ~ 2 to 28% oxygen. Wemore » studied the processing using a catalyst temperature of 704 °C, a reaction exit temperature of 520 °C, and total co-processing run times of 57–75 h. External oxide scaling 5–30 μm thick and internal attack 1–5 μm deep were observed in these short-duration exposures. The greatest extent of internal attack was observed for co-processing with the least stabilized bio-oil, and more so for types 409, 410, 304L, 316L, 317L stainless steel than for type 201. Finally, the internal attack involved porous Cr-rich oxide formation, associated with local Ni-metal enrichment and S-rich nanoparticles, primarily containing Cr or Mn. Implications for alloy selection and corrosion are discussed.« less

Precipitation of sparingly soluble salts in packed sandbeds

NASA Astrophysics Data System (ADS)

Pavlakou, Efstathia I.; Sygouni, Varvara; Paraskeva, Christakis A.

2015-04-01

One of the main problems encountered by the oil extraction industry, is the reduction of the local permeability of the rock formation near the extraction wells because of salt deposition in the pores of the rocks during the injection of brine water to displace the trapped oil ganglia within the oil formations. This phenomenon makes the oil recovery less efficient and under extreme cases the well is abandoned with a large amount of oil entrapped. Several detailed studies have been conducted in the past concerning sand bed consolidation using sparingly soluble salts for varying conditions (e.g. temperature, grain size, sand type, salt concentrations etc) and various salts [1]. Nevertheless, salt precipitation in the rock formation pores under the presence of other miscible or immiscible substances with water has not been investigated in details yet. In the present study, salt (CaCO3) precipitation experiments were performed in small beds packed with sea sand mixed with a low amount of CaCO3 seed grains. The experiments were performed using pure solutions (NaHCO3, CaCl2.2H2O) and solutions mixed with Ethylene Glycol in sand beds. Additionally, precipitation experiments were performed using pure solutions in sand beds saturated with oil phase (n-dodecane) for a wide range of solution supersaturation. During the experiments the ionic strength was kept constant. pH and concentration values of calcium ion of the effluent were measured and the precipitated salt crystals were identified using X-ray Diffraction (XRD) method. At the end of each experiment Scanning Electron Microscope (SEM) was conducted using a sample of the precipitated sand to identify the morphology of the precipitated crystals and their cohesion with sand grains. Acknowledgments This research was partially funded by the European Union (European Social Fund-ESF) and Greek National Funds through the Operational program "Education and Lifelong Learning" under the action Aristeia II (Code No 4420). References [1] Paraskeva C. A., Charalampous P. C., Stokka L. E., Klepetsanis P. G., Koutsoukos P. G., Read P., Ostvold, T. and Payatakes A. C. (2000), ''Sandbed Consolidation with Mineral Precipitation'', Journal of Colloid and Interface Science, 232, 326-339.

Process for obtaining liquid fuel-oil and/or gaseous hydrocarbons from solid carbonaceous feed stocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollaway, J.W.

1978-02-28

A process for forming a fuel-oil from coal is disclosed. The coal is treated in a low temperature carbonization retort to give coke, coal-gas and tar-oil. The coke is converted to water-gas which is then synthesized in a Fischer-Tropsch synthesizer to form fuel-oil. The tar-oil is hydrogenated in a hydro-treater by hydrogen produced from the coal-gas. Hydrogen is produced from coal-gas either in a thermal cracking chamber or by reforming the methane content to hydrogen and passing the resultant hydrogen/carbon monoxide mixture through a water-gas shift reactor and a carbon dioxide scrubber.

Bio-Oil Separation and Stabilization by Supercritical Fluid Fractionation. 2014 Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agblevor, Foster; Petkovic, Lucia; Bennion, Edward

The objective of this project is to use supercritical fluids to separate and fractionate algal-based bio-oils into stable products that can be subsequently upgraded to produce drop-in renewable fuels. To accomplish this objective, algae was grown and thermochemically converted to bio-oils using hydrothermal liquefaction (HTL), pyrolysis, and catalytic pyrolysis. The bio-oils were separated into an extract and a raffinate using near-critical propane or carbon dioxide. The fractions were then subjected to thermal aging studies to determine if the extraction process had stabilized the products. It was found that the propane extract fraction was twice as stable as the parent catalyticmore » pyrolysis bio-oils as measured by the change in viscosity after two weeks of accelerated aging at 80°C. Further, in-situ NMR aging studies found that the propane extract was chemically more stable than the parent bio-oil. Thus the milestone of stabilizing the product was met. A preliminary design of the extraction plant was prepared. The design was based on a depot scale plant processing 20,000,000 gallons per year of bio-oil. It was estimated that the capital costs for such a plant would be $8,700,000 with an operating cost of $3,500,000 per year. On a per gallon of product cost and a 10% annual rate of return, capital costs would represent $0.06 per gallon and operating costs would amount to $0.20 per gallon. Further, it was found that the energy required to run the process represented 6.2% of the energy available in the bio-oil, meeting the milestone of less than 20%. Life cycle analysis and greenhouse gas (GHG) emission analysis found that the energy for running the critical fluid separation process and the GHG emissions were minor compared to all the inputs to the overall well to pump system. For the well to pump system boundary, energetics in biofuel conversion are typically dominated by energy demands in the growth, dewater, and thermochemical process. Bio-oil stabilization by near critical propane extraction had minimal impact in the overall energetics of the process with NER contributions of 0.03. Based on the LCA, the overall conversion pathways were found to be energy intensive with a NER of about 2.3 and 1.2 for catalytic pyrolysis and HTL, respectively. GHG emissions for the catalytic pyrolysis process were greater than that of petroleum diesel at 210 g CO2 eq compared to 18.9 g CO2 eq. Microalgae bio-oil based diesel with thermochemical conversion through HTL meets renewable fuel standards with favorable emission reductions of -10.8 g CO2 eq. The importance of the outcomes is that the critical fluid extraction and stabilization process improved product stability and did so with minimal energy inputs and processing costs. The LCA and GHG emission calculations point toward the HTL pathway as the more favorable thermochemical route towards upgrading algae to bio-fuels. Since the quality of the HTL oil was significantly lower than that of the catalytic pyrolysis bio-oil, the next steps point toward improving the quality of the HTL oils from algae biomass and focusing the critical fluid stabilization on that bio-oil product.« less

Post Retort, Pre Hydro-treat Upgrading of Shale Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon, John

Various oil feedstocks, including oil from oil shale, bitumen from tar sands, heavy oil, and refin- ery streams were reacted with the alkali metals lithium or sodium in the presence of hydrogen or methane at elevated temperature and pressure in a reactor. The products were liquids with sub- stantially reduced metals, sulfur and nitrogen content. The API gravity typically increased. Sodi- um was found to be more effective than lithium in effectiveness. The solids formed when sodium was utilized contained sodium sulfide which could be regenerated electrochemically back to so- dium and a sulfur product using a "Nasicon", sodium ionmore » conducting membrane. In addition, the process was found to be effective reducing total acid number (TAN) to zero, dramatically reduc- ing the asphaltene content and vacuum residual fraction in the product liquid. The process has promise as a means of eliminating sulfur oxide and carbon monoxide emissions. The process al- so opens the possibility of eliminating the coking process from upgrading schemes and upgrad- ing without using hydrogen.« less

Resource recovery of organic sludge as refuse derived fuel by fry-drying process.

PubMed

Chang, Fang-Chih; Ko, Chun-Han; Wu, Jun-Yi; Wang, H Paul; Chen, Wei-Sheng

2013-08-01

The organic sludge and waste oil were collected from the industries of thin film transistor liquid crystal display and the recycled cooking oil. The mixing ratio of waste cooking oil and organic sludge, fry-drying temperatures, fry-drying time, and the characteristics of the organic sludge pellet grain were investigated. After the fry-drying process, the moisture content of the organic sludge pellet grain was lower than 5% within 25 min and waste cooking oil was absorbed on the dry solid. The fry-drying organic sludge pellet grain was easy to handle and odor free. Additionally, it had a higher calorific value than the derived fuel standards and could be processed into organic sludge derived fuels. Thus, the granulation and fry-drying processes of organic sludge with waste cooking oil not only improves the calorific value of organic sludge and becomes more valuable for energy recovery, but also achieves waste material disposal and cost reduction. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physical Properties of Nyamplung Oil (Calophyllum inophyllum L) for Biodiesel Production

NASA Astrophysics Data System (ADS)

Dewang, Syamsir; Suriani; Hadriani, Siti; Bannu; Abdullah, B.

2017-05-01

Worldwide energy crisis due to the too high of energy consumption causes the people trying to find alternative energy to support energy requirements. The use of energy from environmentally friendly plant-based materials into an effort to assist communities in sufficient of national energy needs. Some processing of Nyamplung (Calophyllum inophyllum L) oil production is drying and pressing to produce crude oil. Degumming process is then performed to remove the sap contained in the oil. The next process is to remove free fatty acids (FFA) below 2% that can cause corrosion on the machine when in use. The results performed of the density properties quality to produce oil that appropriate with the international standards by time variation of catalyst. The result was obtained the density value of 0.92108 gr/cm3 at the time of 3 hours by trans-esterification process, and the best yield value was measured at 98.2% in 2 hours stirring of transesterification.

Novel insight into the role of heterotrophic dinoflagellates in the fate of crude oil in the sea.

PubMed

Almeda, Rodrigo; Connelly, Tara L; Buskey, Edward J

2014-12-19

Although planktonic protozoans are likely to interact with dispersed crude oil after a spill, protozoan-mediated processes affecting crude oil pollution in the sea are still not well known. Here, we present the first evidence of ingestion and defecation of physically or chemically dispersed crude oil droplets (1-86 μm in diameter) by heterotrophic dinoflagellates, major components of marine planktonic food webs. At a crude oil concentration commonly found after an oil spill (1 μL L(-1)), the heterotrophic dinoflagellates Noctiluca scintillans and Gyrodinium spirale grew and ingested ~0.37 μg-oil μg-C(dino)(-1) d(-1), which could represent ~17% to 100% of dispersed oil in surface waters when heterotrophic dinoflagellates are abundant or bloom. Egestion of faecal pellets containing crude oil by heterotrophic dinoflagellates could contribute to the sinking and flux of toxic petroleum hydrocarbons in coastal waters. Our study indicates that crude oil ingestion by heterotrophic dinoflagellates is a noteworthy route by which petroleum enters marine food webs and a previously overlooked biological process influencing the fate of crude oil in the sea after spills.