Perform Tests and Document Results and Analysis of Oxide Layer Effects and Comparisons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, E. D.; DelCul, G. D.; Spencer, B. B.

2014-08-30

During the initial feasibility test using actual used nuclear fuel (UNF) cladding in FY 2012, an incubation period of 30–45 minutes was observed in the initial dry chlorination. The cladding hull used in the test had been previously oxidized in a dry air oxidation pretreatment prior to removal of the fuel. The cause of this incubation period was attributed to the resistance to chlorination of an oxide layer imparted by the dry oxidation pretreatment on the cladding. Subsequently in 2013, researchers at the Korea Atomic Energy Institute (KAERI) reported on their chlorination study [R1] on ~9-gram samples of unirradiated ZirloTMmore » cladding tubes that had been previously oxidized in air at 500oC for various time periods to impart oxide layers of varying thickness. In early 2014, discussions with Indefinite Delivery, Indefinite Quantity (IDIQ) contracted technical consultants from Westinghouse described their previous development (and patents) [R2] on methods of chemical washing to remove some or all of the hydrous oxide layer imparted on UNF cladding during irradiation in light water reactors (LWRs) . Thus, the Oak Ridge National Laboratory (ORNL) study, described herein, was planned to extend the KAERI study on the effects of anhydrous oxide layers, but on larger ~100-gram samples of unirradiated zirconium alloy cladding tubes, and to investigate the effects of various methods of chemical pretreatment prior to chlorination with 100% chlorine on the average reaction rates and Cl2 usage efficiencies.« less

Spent nuclear fuel assembly inspection using neutron computed tomography

NASA Astrophysics Data System (ADS)

Pope, Chad Lee

The research presented here focuses on spent nuclear fuel assembly inspection using neutron computed tomography. Experimental measurements involving neutron beam transmission through a spent nuclear fuel assembly serve as benchmark measurements for an MCNP simulation model. Comparison of measured results to simulation results shows good agreement. Generation of tomography images from MCNP tally results was accomplished using adapted versions of built in MATLAB algorithms. Multiple fuel assembly models were examined to provide a broad set of conclusions. Tomography images revealing assembly geometric information including the fuel element lattice structure and missing elements can be obtained using high energy neutrons. A projection difference technique was developed which reveals the substitution of unirradiated fuel elements for irradiated fuel elements, using high energy neutrons. More subtle material differences such as altering the burnup of individual elements can be identified with lower energy neutrons provided the scattered neutron contribution to the image is limited. The research results show that neutron computed tomography can be used to inspect spent nuclear fuel assemblies for the purpose of identifying anomalies such as missing elements or substituted elements. The ability to identify anomalies in spent fuel assemblies can be used to deter diversion of material by increasing the risk of early detection as well as improve reprocessing facility operations by confirming the spent fuel configuration is as expected or allowing segregation if anomalies are detected.

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio program.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregson, Michael Warren; Mo, Tin; Sorenson, Ken Bryce

The authors provide a detailed overview of an on-going, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy-density device. The program participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research program. Sandia National Laboratoriesmore » has the lead role for conducting this research program; test program support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. The authors provide a summary of the overall, multiphase test design and a description of all explosive containment and aerosol collection test components used. They focus on the recently initiated tests on 'surrogate' spent fuel, unirradiated depleted uranium oxide and forthcoming actual spent fuel tests, and briefly summarize similar results from completed surrogate tests that used non-radioactive, sintered cerium oxide ceramic pellets in test rods.« less

A prospective, randomized, double-blind study, comparing unirradiated to irradiated white blood cell transfusions in acute leukemia patients

PubMed Central

Freireich, E J; Lichtiger, B; Mattiuzzi, G; Martinez, F; Reddy, V; Kyle Wathen, J

2013-01-01

A prospective, randomized double-blind study comparing the effects of irradiated and unirradiated white blood cells was conducted in 108 acute leukemia patients with life-threatening infections, refractory to antibiotics. The study demonstrated no significant improvement in 30-day survival or overall survival. Transfusion of unirradiated white cells did not compromise the patient's opportunity to undergo allogeneic stem cell transplant, nor the success rate or overall survival after allogeneic transplant. The important positive finding in this study was that the unirradiated white cells produced a significantly higher increment in circulating granulocytes and in a higher proportion of patients granulocyte count exceeded 1000 per microliter, approaching normal concentrations. The increase in the number and the improved survival of the unirradiated granulocytes suggest that this procedure might potentially be a method to improve the utility of granulocyte transfusions and merits further investigation. The study demonstrated non-inferiority for unirradiated white cells. There were no harmful effects such as graft-versus-host disease, indicating that such studies would be safe to conduct in the future. PMID:23072780

Characterization of un-irradiated MIMAS MOX fuel by Raman spectroscopy and EPMA

NASA Astrophysics Data System (ADS)

Talip, Zeynep; Peuget, Sylvain; Magnin, Magali; Tribet, Magaly; Valot, Christophe; Vauchy, Romain; Jégou, Christophe

2018-02-01

In this study, Raman spectroscopy technique was implemented to characterize un-irradiated MIMAS (MIcronized - MASter blend) MOX fuel samples with average 7 wt.% Pu content and different damage levels, 13 years after fabrication, one year after thermal recovery and soon after annealing, respectively. The impacts of local Pu content, deviation from stoichiometry and self-radiation damage on Raman spectrum of the studied MIMAS MOX samples were assessed. MIMAS MOX fuel has three different phases Pu-rich agglomerate, coating phase and uranium matrix. In order to distinguish these phases, Raman results were associated with Pu content measurements performed by Electron Microprobe Analysis. Raman results show that T2g frequency significantly shifts from 445 to 453 cm-1 for Pu contents increasing from 0.2 to 25 wt.%. These data are satisfactorily consistent with the calculations obtained with Gruneisen parameters. It was concluded that the position of the T2g band is mainly controlled by Pu content and self-radiation damage. Deviation from stoichiometry does not have a significant influence on T2g band position. Self-radiation damage leads to a shift of T2g band towards lower frequency (∼1-2 cm-1 for the UO2 matrix of damaged sample). However, this shift is difficult to quantify for the coating phase and Pu agglomerates given the dispersion of high Pu concentrations. In addition, 525 cm-1 band, which was attributed to sub-stoichiometric structural defects, is presented for the first time for the self-radiation damaged MOX sample. Thanks to the different oxidation resistance of each phase, it was shown that laser induced oxidation could be alternatively used to identify the phases. It is demonstrated that micro-Raman spectroscopy is an efficient technique for the characterization of heterogeneous MOX samples, due to its low spatial resolution.

Elastic Modulus Measurement of ORNL ATF FeCrAl Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Zachary T.; Terrani, Kurt A.; Yamamoto, Yukinori

2015-10-01

Elastic modulus and Poisson’s ratio for a number of wrought FeCrAl alloys, intended for accident tolerant fuel cladding application, are determined via resonant ultrasonic spectroscopy. The results are reported as a function of temperature from room temperature to 850°C. The wrought alloys were in the fully annealed and unirradiated state. The elastic modulus for the wrought FeCrAl alloys is at least twice that of Zr-based alloys over the temperature range of this study. The Poisson’s ratio of the alloys was 0.28 on average and increased very slightly with increasing temperature.

Thermal analysis applied to irradiated propolis

NASA Astrophysics Data System (ADS)

Matsuda, Andrea Harumi; Machado, Luci Brocardo; del Mastro, Nélida Lucia

2002-03-01

Propolis is a resinous hive product, collected by bees. Raw propolis requires a decontamination procedure and irradiation appears as a promising technique for this purpose. The valuable properties of propolis for food and pharmaceutical industries have led to increasing interest in its technological behavior. Thermal analysis is a chemical analysis that gives information about changes on heating of great importance for technological applications. Ground propolis samples were 60Co gamma irradiated with 0 and 10 kGy. Thermogravimetry curves shown a similar multi-stage decomposition pattern for both irradiated and unirradiated samples up to 600°C. Similarly, through differential scanning calorimetry , a coincidence of melting point of irradiated and unirradiated samples was found. The results suggest that the irradiation process do not interfere on the thermal properties of propolis when irradiated up to 10 kGy.

The interaction of molecular hydrogen with α-radiolytic oxidants on a (U,Pu)O2 surface

NASA Astrophysics Data System (ADS)

Bauhn, Lovisa; Hansson, Niklas; Ekberg, Christian; Fors, Patrik; Delville, Rémi; Spahiu, Kastriot

2018-07-01

In order to assess the impact of α-radiolysis of water on the oxidative dissolution of spent fuel, an un-irradiated, annealed MOX fuel pellet with high content of Pu (∼24 wt%), and a specific α-activity of 4.96 GBq/gMOX, was leached in carbonate-containing solutions of low ionic strength. The high Pu content in the pellet stabilizes the (U,Pu)O2(s) matrix towards oxidative dissolution, whereas the α-decays emitted from the surface are expected to produce ∼3.6 × 10-7 mol H2O2/day, contributing to the oxidative dissolution of the pellet. Two sets of leaching tests were conducted under different redox conditions: Ar gas atmosphere and deuterium gas atmosphere. A relatively slow increase of the U and Pu concentrations was observed in the Ar case, with U concentrations increasing from 1·10-6 M after 1 h to ∼7 × 10-5 M after 58 days. Leaching under an atmosphere starting at 1 MPa deuterium gas was undertaken in order to evaluate any effect of dissolved hydrogen on the radiolytic dissolution of the pellet, as well as to investigate any potential recombination of the α-radiolytic products with dissolved deuterium. For the latter purpose, isotopic analysis of the D/H content was carried out on solution samples taken during the leaching. Despite the continuous production of radiolytic oxidants, the concentrations of U and Pu remained quite constant at the level of ∼3 × 10-8 M during the first 30 days, i.e. as long as the deuterium pressure remained higher than 0.8 MPa. These data rule out any oxidative dissolution of the pellet during the first month. The un-irradiated MOX fuel does not contain metallic ε-particles, hence it is mainly the interaction of radiolytic oxidants and dissolved deuterium with the surface of the mixed actinide oxide that causes the neutralization of the oxidants. This conclusion is supported by the steadily increasing levels of HDO measured in the leachate samples.

Influence of gamma radiation on the colour strength and fastness properties of fabric using turmeric (Curcuma longa L .) as natural dye

NASA Astrophysics Data System (ADS)

Bhatti, Ijaz A.; Adeel, Shahid; Jamal, M. Asghar; Safdar, Muhammad; Abbas, Muhammad

2010-05-01

The effect of gamma radiation on the dyeing of cotton with extract of turmeric ( Curcuma longa L.) powder has been investigated. Cotton fabric and turmeric powder were irradiated to absorbed doses of 1, 2, 3, 4 and 6 kGy using Co-60 gamma irradiator. Dyeing parameters such as temperature, pH and mordant concentration were optimized. Dyeing was performed using un-irradiated and irradiated cotton with the extracts of un-irradiated and irradiated turmeric powder in order to investigate the effect of radiation treatment on the colour strength of dyed fabric. The reported data of un-irradiated and irradiated fabrics dyed with un-irradiated and irradiated dyes were obtained using the spectraflash SF-650. The colourfastness to light, rubbing- and washing-fastness properties showed that gamma irradiation has improved the dyeing characteristics from fair to good.

Special Analysis for the Disposal of the INL Waste Associated with the Unirradiated Light Water Breeder Reactor (LWBR) Waste Stream at the Area 5 Radioactive Waste Management Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shott, Gregory

This special analysis (SA) evaluates whether the Idaho National Laboratory (INL) Waste Associated with the Unirradiated Light Water Breeder Reactor (LWBR) waste stream (INEL167203QR1, Revision 0) is suitable for shallow land burial (SLB) at the Area 5 Radioactive Waste Management Site (RWMS) on the Nevada National Security Site (NNSS). Disposal of the INL Waste Associated with the Unirradiated LWBR waste meets all U.S. Department of Energy (DOE) Manual DOE M 435.1-1, “Radioactive Waste Management Manual,” Chapter IV, Section P performance objectives (DOE 1999). The INL Waste Associated with the Unirradiated LWBR waste stream is recommended for acceptance with the conditionmore » that the total uranium-233 ( 233U) inventory be limited to 2.7E13 Bq (7.2E2 Ci).« less

Azimuthally anisotropic hydride lens structures in Zircaloy 4 nuclear fuel cladding: High-resolution neutron radiography imaging and BISON finite element analysis

NASA Astrophysics Data System (ADS)

Lin, Jun-Li; Zhong, Weicheng; Bilheux, Hassina Z.; Heuser, Brent J.

2017-12-01

High-resolution neutron radiography has been used to image bulk circumferential hydride lens particles in unirradiated Zircaloy 4 tubing cross section specimens. Zircaloy 4 is a common light water nuclear reactor (LWR) fuel cladding; hydrogen pickup, hydride formation, and the concomitant effect on the mechanical response are important for LWR applications. Ring cross section specimens with three hydrogen concentrations (460, 950, and 2830 parts per million by weight) and an as-received reference specimen were imaged. Azimuthally anisotropic hydride lens particles were observed at 950 and 2830 wppm. The BISON finite element analysis nuclear fuel performance code was used to model the system elastic response induced by hydride volumetric dilatation. The compressive hoop stress within the lens structure becomes azimuthally anisotropic at high hydrogen concentrations or high hydride phase fraction. This compressive stress anisotropy matches the observed lens anisotropy, implicating the effect of stress on hydride formation as the cause of the observed lens azimuthal asymmetry. The cause and effect relation between compressive stress and hydride lens anisotropy represents an indirect validation of a key BISON output, the evolved hoop stress associated with hydride formation.

Progress in the Assessment of Waste-forms for the Immobilisation of UK Civil Plutonium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison, M.T.; Scales, C.R.; Maddrell, E.R.

The alternatives for the disposition of the UK's civil plutonium stocks are currently being investigated by Nexia Solutions Ltd. on behalf of the Nuclear Decommissioning Authority (NDA). A number of scenarios are currently being considered depending on the strategic requirements of the UK. The two main disposition options are: re-use as MOX (Mixed Oxide) fuel in reactors, or immobilisation in the event of any material being declared surplus to requirements. The amount of Pu which will require immobilisation will depend on future UK nuclear strategy, along with the extent of any stocks deemed unsuitable for re-use. However, it is likelymore » that some portion will have to be immobilised and therefore three credible waste-forms are under consideration; ceramic, glass and 'immobilisation' MOX. These are currently being developed and assessed in a systematic programme that involves periodic evaluation against a range of criteria. In this way, by down-selecting on the basis of robust and technical review, the most appropriate option for immobilising surplus civil plutonium in the UK can be recommended. The latest results from the immobilisation experimental programme are presented following the de-selection of the least favourable glass and ceramic candidates. The main criteria for this decision were waste loading, durability, processability, criticality and proliferation resistance. In addition, the durability of unirradiated MOX fuel is being examined to determine its potential as a wasteform for Pu, and recent leach test data is discussed. The current evaluation comprises not only a comparison of the relevant physical properties of the various waste-forms, but also key processing parameters, e.g. glass viscosity and melter technology, ceramic fabrication routes, and criticality issues. Other important aspects of the long-term behaviour of the waste-forms under consideration in a potential repository environment, such as radiation damage, criticality control and the properties of any neutron poisons present, are also included. (authors)« less

RH-TRU Waste Characterization by Acceptable Knowledge at the Idaho National Engineering and Environmental Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schulz, C.; Givens, C.; Bhatt, R.

2003-02-24

Idaho National Engineering and Environmental Laboratory (INEEL) is conducting an effort to characterize approximately 620 drums of remote-handled (RH-) transuranic (TRU) waste currently in its inventory that were generated at the Argonne National Laboratory-East (ANL-E) Alpha Gamma Hot Cell Facility (AGHCF) between 1971 and 1995. The waste was generated at the AGHCF during the destructive examination of irradiated and unirradiated fuel pins, targets, and other materials from reactor programs at ANL-West (ANL-W) and other Department of Energy (DOE) reactors. In support of this effort, Shaw Environmental and Infrastructure (formerly IT Corporation) developed an acceptable knowledge (AK) collection and management programmore » based on existing contact-handled (CH)-TRU waste program requirements and proposed RH-TRU waste program requirements in effect in July 2001. Consistent with Attachments B-B6 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Facility Permit (HWFP) and th e proposed Class 3 permit modification (Attachment R [RH-WAP] of this permit), the draft AK Summary Report prepared under the AK procedure describes the waste generating process and includes determinations in the following areas based on AK: physical form (currently identified at the Waste Matrix Code level); waste stream delineation; applicability of hazardous waste numbers for hazardous waste constituents; and prohibited items. In addition, the procedure requires and the draft summary report contains information supporting determinations in the areas of defense relationship and radiological characterization.« less

Unirradiated testing of the demonstration-scale ceramic waste form at ANL-West

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goff, K.M.; Simpson, M.F.; Bateman, K.J.

1997-12-01

The ceramic waste form is being developed by Argonne National Laboratory (ANL) as part of the demonstration of the electrometallurgical treatment of spent nuclear fuel for disposal. The alkali, alkaline earth, halide, and rare earth fission products are stabilized in zeolite, which is combined with glass and processed in a hot isostatic press (HIP) to form a ceramic composite. The transuranics, including plutonium, are also stabilized in this high-level waste. Most of the laboratory-scale development work is performed in the Chemical Technology Division of ANL in Illinois. At ANL-West in Idaho, this technology is being demonstrated on an engineering scalemore » before implementation with irradiated materials in a remote environment.« less

Research Reactor Preparations for the Air Shipment of Highly Enriched Uranium from Romania

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. J. Allen; I. Bolshinsky; L. L. Biro

2010-03-01

In June 2009 two air shipments transported both unirradiated (fresh) and irradiated (spent) Russian-origin highly enriched uranium (HEU) nuclear fuel from two research reactors in Romania to the Russian Federation for conversion to low enriched uranium. The Institute for Nuclear Research at Pitesti (SCN Pitesti) shipped 30.1 kg of HEU fresh fuel pellets to Dimitrovgrad, Russia and the Horia Hulubei National Institute of Physics and Nuclear Engineering (IFIN-HH) shipped 23.7 kilograms of HEU spent fuel assemblies from the VVR S research reactor at Magurele, Romania, to Chelyabinsk, Russia. Both HEU shipments were coordinated by the Russian Research Reactor Fuel Returnmore » Program (RRRFR) as part of the U.S. Department of Energy Global Threat Reduction Initiative (GTRI), were managed in Romania by the National Commission for Nuclear Activities Control (CNCAN), and were conducted in cooperation with the Russian Federation State Corporation Rosatom and the International Atomic Energy Agency. Both shipments were transported by truck to and from respective commercial airports in Romania and the Russian Federation and stored at secure nuclear facilities in Russia until the material is converted into low enriched uranium. These shipments resulted in Romania becoming the 3rd country under the RRRFR program and the 14th country under the GTRI program to remove all HEU. This paper describes the research reactor preparations and license approvals that were necessary to safely and securely complete these air shipments of nuclear fuel.« less

A pulse-controlled modified-burst test instrument for accident-tolerant fuel cladding

DOE PAGES

Cinbiz, M. Nedim; Brown, Nicholas R.; Terrani, Kurt A.; ...

2017-06-03

Pellet-cladding mechanical interaction due to thermal expansion of nuclear fuel pellets during a reactivity-initiated accident (RIA) is a potential mechanism for failure of nuclear fuel cladding. To investigate the mechanical behavior of cladding during an RIA, we developed a mechanical pulse-controlled modified burst test instrument that simulates transient events with a pulse width from 10 to 300 ms. This paper includes validation tests of unirradiated and prehydrided ZIRLO cladding tubes. A ZIRLO cladding sample with a hydrogen content of 168 wt. ppm showed ductile behavior and failed at the maximum limits of the test setup with hoop strain to failuremore » greater than 9.2%. ZIRLO samples showed high resistance to failure even at very high hydrogen contents (1,466 wt. ppm). When the hydrogen content was increased to 1,554 wt. ppm, brittle-like behavior was observed at a hoop strain of 2.5%. Preliminary scoping tests at room temperature with FeCrAl tubes were conducted to imitate the pulse behavior of transient test reactors during integral tests. The preliminary FeCrAl tests are informative from the perspective of characterizing the test rig and supporting the design of integral tests for current and potentially accident tolerant cladding materials.« less

A pulse-controlled modified-burst test instrument for accident-tolerant fuel cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cinbiz, M. Nedim; Brown, Nicholas R.; Terrani, Kurt A.

Pellet-cladding mechanical interaction due to thermal expansion of nuclear fuel pellets during a reactivity-initiated accident (RIA) is a potential mechanism for failure of nuclear fuel cladding. To investigate the mechanical behavior of cladding during an RIA, we developed a mechanical pulse-controlled modified burst test instrument that simulates transient events with a pulse width from 10 to 300 ms. This paper includes validation tests of unirradiated and prehydrided ZIRLO cladding tubes. A ZIRLO cladding sample with a hydrogen content of 168 wt. ppm showed ductile behavior and failed at the maximum limits of the test setup with hoop strain to failuremore » greater than 9.2%. ZIRLO samples showed high resistance to failure even at very high hydrogen contents (1,466 wt. ppm). When the hydrogen content was increased to 1,554 wt. ppm, brittle-like behavior was observed at a hoop strain of 2.5%. Preliminary scoping tests at room temperature with FeCrAl tubes were conducted to imitate the pulse behavior of transient test reactors during integral tests. The preliminary FeCrAl tests are informative from the perspective of characterizing the test rig and supporting the design of integral tests for current and potentially accident tolerant cladding materials.« less

Isoconversional approach for non-isothermal decomposition of un-irradiated and photon-irradiated 5-fluorouracil.

PubMed

Mohamed, Hala Sh; Dahy, AbdelRahman A; Mahfouz, Refaat M

2017-10-25

Kinetic analysis for the non-isothermal decomposition of un-irradiated and photon-beam-irradiated 5-fluorouracil (5-FU) as anti-cancer drug, was carried out in static air. Thermal decomposition of 5-FU proceeds in two steps. One minor step in the temperature range of (270-283°C) followed by the major step in the temperature range of (285-360°C). The non-isothermal data for un-irradiated and photon-irradiated 5-FU were analyzed using linear (Tang) and non-linear (Vyazovkin) isoconversional methods. The results of the application of these free models on the present kinetic data showed quite a dependence of the activation energy on the extent of conversion. For un-irradiated 5-FU, the non-isothermal data analysis indicates that the decomposition is generally described by A3 and A4 modeles for the minor and major decomposition steps, respectively. For a photon-irradiated sample of 5-FU with total absorbed dose of 10Gy, the decomposition is controlled by A2 model throughout the coversion range. The activation energies calculated in case of photon-irradiated 5-FU were found to be lower compared to the values obtained from the thermal decomposition of the un-irradiated sample probably due to the formation of additional nucleation sites created by a photon-irradiation. The decomposition path was investigated by intrinsic reaction coordinate (IRC) at the B3LYP/6-311++G(d,p) level of DFT. Two transition states were involved in the process by homolytic rupture of NH bond and ring secession, respectively. Published by Elsevier B.V.

Topical Hazard Evaluation Program of Candidate Insect Repellent AI3-30180-c, US Department of Agriculture Proprietary Chemical, April 1982 - September 1984.

DTIC Science & Technology

1985-01-10

irritation photochemical chemical and 10 percent reaction under test con- irritation in humans. (wlv) Oil of Bergamot ditions. 2 * - Study No. 75-51-0367-85...control (oil of Bergamot ), than unirradiated skin areas. a and diluent were applied to additional skin areas to serve as unirradiated control sites

Detection of Irradiation Treatment of Foods Using DNA `Comet Assay'

NASA Astrophysics Data System (ADS)

Khan, Hasan M.; Delincée, Henry

1998-06-01

Microgel electrophoresis of single cells (DNA comet assay) has been investigated to detect irradiation treatment of some food samples. These samples of fresh and frozen rainbow trout, red lentil, gram and sliced almonds were irradiated to 1 or 2 kGy using 10 MeV electron beam from a linear accelerator. Rainbow trout samples yielded good results with samples irradiated to 1 or 2 kGy showing fragmentation of DNA and, therefore, longer comets with no intact cells. Unirradiated samples showed shorter comets with a significant number of intact cells. For rainbow trout stored in a freezer for 11 days the irradiated samples can still be discerned by electrophoresis from unirradiated samples, however, the unirradiated trouts also showed some longer comets besides some intact cells. Radiation treatment of red lentils can also be detected by this method, i.e. no intact cells in 1 or 2 kGy irradiated samples and shorter comets and some intact cells in unirradiated samples. However, the results for gram and sliced almond samples were not satisfactory since some intact DNA cells were observed in irradiated samples as well. Probably, incomplete lysis has led to these deviating results.

The influence of late-stage pupal irradiation and increased irradiated: un-irradiated male ratio on mating competitiveness of the malaria mosquito Anopheles arabiensis Patton.

PubMed

Helinski, M E H; Knols, B G J

2009-06-01

Competitiveness of released males in genetic control programmes is of critical importance. In this paper, we explored two scenarios to compensate for the loss of mating competitiveness after pupal stage irradiation in males of the malaria mosquito Anopheles arabiensis. First, competition experiments with a higher ratio of irradiated versus un-irradiated males were performed. Second, pupae were irradiated just prior to emergence and male mating competitiveness was determined. Males were irradiated in the pupal stage with a partially or fully-sterilizing dose of 70 or 120 Gy, respectively. Pupae were irradiated aged 20-26 h (young) as routinely performed, or the pupal stage was artificially prolonged by cooling and pupae were irradiated aged 42-48 h (old). Irradiated males competed at a ratio of 3:1:1 to un-irradiated males for mates in a large cage design. At the 3:1 ratio, the number of females inseminated by males irradiated with 70 Gy as young pupae was similar to the number inseminated by un-irradiated males for the majority of the replicates. At 120 Gy, significantly fewer females were inseminated by irradiated than by un-irradiated males. The irradiation of older pupae did not result in a significantly improved male mating competitiveness compared to the irradiation of young pupae. Our findings indicate that the loss of competitiveness after pupal stage irradiation can be compensated for by a threefold increase of irradiated males, but only for the partially-sterilizing dose. In addition, cooling might be a useful tool to facilitate handling processes of large numbers of mosquitoes in genetic control programmes.

Evaluation of the limulus amoebocyte lysate test in conjunction with a gram negative bacterial plate count for detecting irradiation of chicken

NASA Astrophysics Data System (ADS)

Scotter, Susan L.; Wood, Roger; McWeeny, David J.

A study to evaluate the potential of the Limulus amoebocyte lysate (LAL) test in conjuction with a Gram negative bacteria (GNB) plate count for detecting the irradiation of chicken is described. Preliminary studies demonstrated that chickens irradiated at an absorbed dose of 2.5 kGy could be differentiated from unirradiated birds by measuring levels of endotoxin and of numbers of GNB on chicken skin. Irradiated birds were found to have endotoxin levels similar to those found in unirradiated birds but significantly lower numbers of GNB. In a limited study the test was found to be applicable to birds from different processors. The effect of temperature abuse on the microbiological profile, and thus the efficacy of the test, was also investigated. After temperature abuse, the irradiated birds were identifiable at worst up to 3 days after irradiation treatment at the 2.5 kGy level and at best some 13 days after irradiation. Temperature abuse at 15°C resulted in rapid recovery of surviving micro-organisms which made differentiation of irradiated and unirradiated birds using this test unreliable. The microbiological quality of the bird prior to irradiation treatment also affected the test as large numbers of GNB present on the bird prior to irradiation treatment resulted in larger numbers of survivors. In addition, monitoring the developing flora after irradiation treatment and during subsequent chilled storage also aided differentiation of irradiated and unirradiated birds. Large numbers of yeasts and Gram positive cocci were isolated from irradiated carcasses whereas Gram negative oxidative rods were the predominant spoilage flora on unirradiated birds.

Cell cycle tracking for irradiated and unirradiated bystander cells in a single colony with exposure to a soft X-ray microbeam.

PubMed

Kaminaga, Kiichi; Noguchi, Miho; Narita, Ayumi; Hattori, Yuya; Usami, Noriko; Yokoya, Akinari

2016-11-01

To establish a new experimental technique to explore the photoelectric and subsequent Auger effects on the cell cycles of soft X-ray microbeam-irradiated cells and unirradiated bystander cells in a single colony. Several cells located in the center of a microcolony of HeLa-Fucci cells consisting of 20-80 cells were irradiated with soft X-ray (5.35 keV) microbeam using synchrotron radiation as a light source. All cells in the colony were tracked for 72 h by time-lapse microscopy imaging. Cell cycle progression, division, and death of each cell in the movies obtained were analyzed by pedigree assay. The number of cell divisions in the microcolony was also determined. The fates of these cells were clarified by tracking both irradiated and unirradiated bystander cells. Irradiated cells showed significant cell cycle retardation, explosive cell death, or cell fusion after a few divisions. These serious effects were also observed in 15 and 26% of the bystander cells for 10 and 20 Gy irradiation, respectively, and frequently appeared in at least two daughter or granddaughter cells from a single-parent cell. We successfully tracked the fates of microbeam-irradiated cells and unirradiated bystander cells with live cell recordings, which have revealed the dynamics of soft X-ray irradiated and unirradiated bystander cells for the first time. Notably, cell deaths or cell cycle arrests frequently arose in closely related cells. These details would not have been revealed by a conventional immunostaining imaging method. Our approach promises to reveal the dynamic cellular effects of soft X-ray microbeam irradiation and subsequent Auger processes from various endpoints in future studies.

Tensile and fatigue data for irradiated and unirradiated AISI 310 stainless steel and titanium - 5 percent aluminum - 2.5 percent tin: Application of the method of universal slopes

NASA Technical Reports Server (NTRS)

Debogdan, C. E.

1973-01-01

Irradiated and unirradiated tensile and fatigue specimens of AISI 310 stainless steel and Ti-5Al-2.5Sn were tested in the range of 100 to 10,000 cycles to failure to determine the applicability of the method of universal slopes to irradiated materials. Tensile data for both materials showed a decrease in ductility and increase in ultimate tensile strength due to irradiation. Irradiation caused a maximum change in fatigue life of only 15 to 20 percent for both materials. The method of universal slopes predicted all the fatigue data for the 310 SS (irradiated as well as unirradiated) within a life factor of 2. For the titanium alloy, 95 percent of the data was predicted within a life factor of 3.

Microstructural Characterization of Irradiated U0.7ZrH1.6 Using Ultrasonic Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramuhalli, Pradeep; Jacob, Richard E.; MacFarlan, Paul J.

In recent years, there has been an increased level of effort to understand the changes in microstructure that occur due to irradiation of nuclear fuel. The primary driver for this increased effort is the potential for designing new fuels that are safer and more reliable, in turn enabling new and improved reactor technologies. Much of the data on microstructural change in irradiated fuels is generated through a host of post irradiation examination techniques such as optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) to determine grain structure, porosity, crack geometry, etc. in irradiated fuels. Such “traditional”more » examination techniques were recently used to characterize a novel new fuel consisting of U0.17ZrH1.6 pellets bonded to zircaloy-2 cladded with lead-bismuth eutectic before and after irradiation. However, alternative methods such as ultrasonic inspection can provide an opportunity for nondestructively assessing microstructure in both in-pile and post-irradiation examinations. In this paper, we briefly describe initial results of ultrasonic examination of the U0.17ZrH1.6 pellets (unirradiated and irradiated), in a post-irradiation examination study. Data indicate some correlation with microstructural changes due to irradiation; however, it is not clear what the specific microstructural changes are that are influencing the ultrasonic measurements. Interestingly, specimens with nominally identical burnup show differences in ultrasonic signatures, indicating apparent microstructural differences between these specimens. A summary of the experimental study, preliminary data and findings are presented in this short paper. Additional details of the analysis will be included in the presentation.« less

$gamma$-RAY PROCESSING OF RICE. (IV.) STUDIES ON THE AVAILABILITY OF $gamma$-IRRADIATED RICE FOR KOJI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishimura, A.; Takaoka, K.

The availability of rice, gamma -irradiated up to 4.6 x 10/sup 4/ and 3.5 x 10/sup 5/r for koji was studied. The enzyme activities of koji of the steamed samples were stronger than the unirradiated rice in amylase and protease. The sensory test on the once-steamed irradiated rice was almost the same as the twice-steamed unirradiated rice. (OID)

Application of subsize specimens in nuclear plant life extension

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosinski, S.T.; Kumar, A.S.; Cannon, S.C.

1991-01-01

The US Department of Energy is sponsoring a research effort through Sandia National Laboratories and the University of Missour-Rolla to test a correlation for the upper shelf energy (USE) values obtained from the impact testing of subsize Charpy V-notch specimens to those obtained from the testing of full size samples. The program involves the impact testing of unirradiated and irradiated full, half, and third size Charpy V-notch specimens. To verify the applicability of the correlation on LWR materials unirradiated and irradiated full, half, and third size Charpy V-notch specimens of a commercial pressure vessel steel (ASTM A533 Grade B) willmore » be tested. This paper will provide details of the program and present results obtained from the application of the developed correlation methodology to the impact testing of the unirradiated full, half, and third size A533 Grade B Charpy V-notch specimens.« less

Application of subsize specimens in nuclear plant life extension

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosinski, S.T.; Kumar, A.S.; Cannon, S.C.

1991-12-31

The US Department of Energy is sponsoring a research effort through Sandia National Laboratories and the University of Missour-Rolla to test a correlation for the upper shelf energy (USE) values obtained from the impact testing of subsize Charpy V-notch specimens to those obtained from the testing of full size samples. The program involves the impact testing of unirradiated and irradiated full, half, and third size Charpy V-notch specimens. To verify the applicability of the correlation on LWR materials unirradiated and irradiated full, half, and third size Charpy V-notch specimens of a commercial pressure vessel steel (ASTM A533 Grade B) willmore » be tested. This paper will provide details of the program and present results obtained from the application of the developed correlation methodology to the impact testing of the unirradiated full, half, and third size A533 Grade B Charpy V-notch specimens.« less

Use of UO 2 films for electrochemical studies

NASA Astrophysics Data System (ADS)

Miserque, F.; Gouder, T.; Wegen, D. H.; Bottomley, P. D. W.

2001-10-01

UO 2 films have been prepared by dc reactive sputtering of a uranium metal target in an Ar/O 2 atmosphere. We have used the films deposited on gold substrates as working electrodes for electrochemical investigations as simulating the surfaces of fuel pellets. Film composition was determined by photoelectron spectroscopy (XPS and UPS) and X-ray diffraction (XRD). The oxide stoichiometry as a function of deposition conditions was determined and the appropriate conditions for UO 2.0 formation established. AC impedance and cyclic voltammetry measurements were performed. A double RC electrical equivalent circuit was used to fit the data from impedance measurements, similar to those used in unirradiated UO 2 or spent fuel pellets. However due to the porosity or adhesion defects on the thin films that permitted a direct contact between the solution and the gold substrate, we were obliged to add a contribution simulating the water-gold system. Cyclic voltammetry measurements show the influence of pH on the dissolution mechanism. Alkaline solutions permit the formation of an oxidised layer (UO 2.33) which is not present in the acidic solutions. In both pH=2 and pH=6 solutions, a U VI species layer is formed.

Bystander effects in unicellular organisms.

PubMed

DeVeaux, Linda C; Durtschi, Lynn S; Case, Jonathan G; Wells, Douglas P

2006-05-11

Radiation-induced bystander effects have been seen in mammalian cells from diverse origins. These effects can be transmitted through the medium to cells not present at the time of irradiation. We have developed an assay for detecting bystander effects in the unicellular eukaryote, the fission yeast Schizosaccharomyces pombe. This assay allows maximal exposure of unirradiated cells to cells that have received electron beam irradiation. S. pombe cells were irradiated with 16-18 MeV electrons from a pulsed electron LINAC. When survival of the irradiated cells decreased to approximately 50%, forward-mutation to 2-deoxy-d-glucose resistance increased in the unirradiated bystander cells. Further increase in dose had no additional effect on this increase. In order to detect this response, it was necessary for the irradiated cell/unirradiated cell ratio to be high. Other cellular stresses, such as heat treatment, UV irradiation, and bleomycin exposure, also caused a detectable response in untreated cells grown with the treated cells. We discuss evolutionary implications of these results.

Identification of irradiated spices by the use of thermoluminescence method (TL)

NASA Astrophysics Data System (ADS)

Sharifzadeh, M.; Sohrabpour, M.

1993-07-01

In this paper the results of the investigations of identification of irradiated spices by the use of thermoluminescence method is reported. The materials used were black and red peppers, turmeric, cinnamon, and garlic powder. Gamma Cell 220 was used for irradiating samples at dose values of 2.5, 5, 7.5 and 10 kGy respectively. The TL intensity of the unirradiated spices as well as the fading characteristics of the irradiated samples having received a dose of 10 kGy have been measured. Post-irradiation temperature treatment of the irradiated (10 kGy) and unirradiated samples at 60°C and 100°C for 24 hours have been also performed. The results show that the TL intensities of unirradiated and irradiated samples from different batches of each spice are fairly distributed. A reasonable TL intensity versus dose has been observed in nearly all cases. Based on the observations made it is possible to distinguish irradiated spices after (4-9) months post-irradiation.

Precession electron diffraction for SiC grain boundary characterization in unirradiated TRISO fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lillo, T. M.; van Rooyen, I. J.; Wu, Y. Q.

Precession electron diffraction (PED), a transmission electron microscopy-based technique, has been evaluated for the suitability for evaluating grain boundary character in the SiC layer of tristructural isotropic (TRISO) fuel. Although the ultimate goal is to determine the grain boundary characteristics of fission product containing grain boundaries of neutron irradiated SiC, our work reports the effect of transmission electron microscope (TEM) lamella thickness on quality of data and establishes a baseline comparison on grain boundary characteristics determined previously using a conventional EBSD scanning electron microscope (SEM) based technique. In general, it was determined that the lamella thickness produced using the standardmore » FIB fabrication process, is sufficient to provide reliable PED measurements with thicker lamellae (~120 nm) produce higher quality orientation data. Analysis of grain boundary character from the TEM-based PED data showed a much lower fraction of low angle grain boundaries compared to SEM-based EBSD data from the SiC layer of the same TRISO-coated particle as well as a SiC layer deposited at a slightly lower temperature. The fractions of high angle and CSL-related grain boundaries determined by PED are similar to those found using SEM-based EBSD. Since the grain size of the SiC layer of TRSIO fuel can be as small as 250 nm [12], depending on the fabrication parameters, and grain boundary fission product precipitates can be nano-sized, the TEM-based PED orientation data collection method is preferred to determine an accurate representation of the relative fractions of low angle, high angle and CSL-related grain boundaries. It was concluded that although the resolution of the PED data is better by more than an order of magnitude, data acquisition times may be significantly longer or the number of areas analyzed significantly larger than the SEM-based method to obtain a statistically relevant distribution. Also, grain size could be accurately determined but significantly larger analysis areas than those used in this study would be required.« less

Precession electron diffraction for SiC grain boundary characterization in unirradiated TRISO fuel

DOE PAGES

Lillo, T. M.; van Rooyen, I. J.; Wu, Y. Q.

2016-06-16

Precession electron diffraction (PED), a transmission electron microscopy-based technique, has been evaluated for the suitability for evaluating grain boundary character in the SiC layer of tristructural isotropic (TRISO) fuel. Although the ultimate goal is to determine the grain boundary characteristics of fission product containing grain boundaries of neutron irradiated SiC, our work reports the effect of transmission electron microscope (TEM) lamella thickness on quality of data and establishes a baseline comparison on grain boundary characteristics determined previously using a conventional EBSD scanning electron microscope (SEM) based technique. In general, it was determined that the lamella thickness produced using the standardmore » FIB fabrication process, is sufficient to provide reliable PED measurements with thicker lamellae (~120 nm) produce higher quality orientation data. Analysis of grain boundary character from the TEM-based PED data showed a much lower fraction of low angle grain boundaries compared to SEM-based EBSD data from the SiC layer of the same TRISO-coated particle as well as a SiC layer deposited at a slightly lower temperature. The fractions of high angle and CSL-related grain boundaries determined by PED are similar to those found using SEM-based EBSD. Since the grain size of the SiC layer of TRSIO fuel can be as small as 250 nm [12], depending on the fabrication parameters, and grain boundary fission product precipitates can be nano-sized, the TEM-based PED orientation data collection method is preferred to determine an accurate representation of the relative fractions of low angle, high angle and CSL-related grain boundaries. It was concluded that although the resolution of the PED data is better by more than an order of magnitude, data acquisition times may be significantly longer or the number of areas analyzed significantly larger than the SEM-based method to obtain a statistically relevant distribution. Also, grain size could be accurately determined but significantly larger analysis areas than those used in this study would be required.« less

Radiation induced corrosion of copper for spent nuclear fuel storage

NASA Astrophysics Data System (ADS)

Björkbacka, Åsa; Hosseinpour, Saman; Johnson, Magnus; Leygraf, Christofer; Jonsson, Mats

2013-11-01

The long term safety of repositories for radioactive waste is one of the main concerns for countries utilizing nuclear power. The integrity of engineered and natural barriers in such repositories must be carefully evaluated in order to minimize the release of radionuclides to the biosphere. One of the most developed concepts of long term storage of spent nuclear fuel is the Swedish KBS-3 method. According to this method, the spent fuel will be sealed inside copper canisters surrounded by bentonite clay and placed 500 m down in stable bedrock. Despite the importance of the process of radiation induced corrosion of copper, relatively few studies have been reported. In this work the effect of the total gamma dose on radiation induced corrosion of copper in anoxic pure water has been studied experimentally. Copper samples submerged in water were exposed to a series of total doses using three different dose rates. Unirradiated samples were used as reference samples throughout. The copper surfaces were examined qualitatively using IRAS and XPS and quantitatively using cathodic reduction. The concentration of copper in solution after irradiation was measured using ICP-AES. The influence of aqueous radiation chemistry on the corrosion process was evaluated based on numerical simulations. The experiments show that the dissolution as well as the oxide layer thickness increase upon radiation. Interestingly, the evaluation using numerical simulations indicates that aqueous radiation chemistry is not the only process driving the corrosion of copper in these systems.

RIA simulation tests using driver tube for ATF cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cinbiz, Mahmut N.; Brown, N. R.; Lowden, R. R.

Pellet-cladding mechanical interaction (PCMI) is a potential failure mechanism for accident-tolerant fuel (ATF) cladding candidates during a reactivity-initiated accident (RIA). This report summarizes Fiscal Year (FY) 2017 research activities that were undertaken to evaluate the PCMI-like hoop-strain-driven mechanical response of ATF cladding candidates. To achieve various RIA-like conditions, a modified-burst test (MBT) device was developed to produce different mechanical pulses. The calibration of the MBT instrument was accomplished by performing mechanical tests on unirradiated Generation-I iron-chromium-aluminum (FeCrAl) alloy samples. Shakedown tests were also conducted in both FY 2016 and FY 2017 using unirradiated hydrided ZIRLO™ tube samples. This milestone reportmore » focuses on testing of ATF materials, but the benchmark tests with hydrided ZIRLO™ tube samples are documented in a recent journal article.a For the calibration and benchmark tests, the hoop strain was monitored using strain gauges attached to the sample surface in the hoop direction. A novel digital image correlation (DIC) system composed of a single high-speed camera and an array of six mirrors was developed for the MBT instrument to better resolve the failure behavior of samples and to provide useful data for validation of high-fidelity modeling and simulation tools. The DIC system enable a 360° view of a sample’s outer surface. This feature was added to the instrument to determine the precise failure location on a sample’s surface for strain predictions. The DIC system was tested on several silicon carbide fiber/silicon carbide matrix (SiC/SiC) composite tube samples at various pressurization rates of the driver tube (which correspond to the strain rates for the samples). The hoop strains for various loading conditions were determined for the SiC/SiC composite tube samples. Future work is planned to enhance understanding of the failure behavior of the ATF cladding candidates of age-hardened FeCrAl alloys and SiC/SiC composites in detail during RIA conditions informed by the computational studies performed under the US Department of Energy Office of Nuclear Energy Advanced Fuels Campaign. The testing instrument and the new DIC system will be further developed to reach different stress-state conditions and to perform tests at elevated temperatures.« less

Effects of Radiation and Long-Term Thermal Cycling on EPC 1001 Gallium Nitride Transistors

NASA Technical Reports Server (NTRS)

Patterson, Richard L.; Scheick, Leif; Lauenstein, Jean-Marie; Casey, Megan; Hammoud, Ahmad

2012-01-01

Electronics designed for use in NASA space missions are required to work efficiently and reliably under harsh environment conditions. These include radiation, extreme temperatures, and thermal cycling, to name a few. Data obtained on long-term thermal cycling of new un-irradiated and irradiated samples of EPC1001 gallium nitride enhancement-mode transistors are presented. This work was done by a collaborative effort including GRC, GSFC, and support the NASA www.nasa.gov 1 JPL in of Electronic Parts and Packaging (NEPP) Program

Fungal decontamination and enhancement of shelf life of edible split beans of wild legume Canavalia maritima by the electron beam irradiation

NASA Astrophysics Data System (ADS)

Supriya, P.; Sridhar, K. R.; Ganesh, S.

2014-03-01

Ripened split beans of the coastal sand dune wild legume Canavalia maritima serve as one of the traditional nutritional sources of the coastal dwellers in Southwest coast of India. Nine fungi were isolated from the unirradiated dry beans by plating on the potato dextrose agar medium. Toxigenic fungus Aspergillus niger showed the highest incidence (33-50%) followed by Aspergillus flavus (14-20%) and Penicillium chrysogenum (7-13%). Unirradiated dry beans and irradiated dry beans with electron beam doses 2.5, 5, 10 and 15 kGy were monitored for occurrence of fungal species and their incidence during 0, 3 and 6 months storage period under laboratory conditions. Irradiation resulted in dose-dependent decrease in fungal species (5-7, 4-6, 3-6 and 0 on irradiation at 0, 2.5, 5 and 10 or 15 kGy, respectively) as well as incidence (80-99, 19-46, 13-21 and 0%, respectively). Although aflatoxins (B1 and B2) were found below detectable level (<2 ng/g) in 0, 3 and 6 months stored unirradiated and irradiated beans (2.5 and 5 kGy), they were not present in beans irradiated with 10 and 15 kGy. In spite of occurrence of toxigenic fungus Aspergillus ochraceus in unirradiated and irradiated beans (2.5 and 5 kGy) stored for 3 and 6 months, the beans were devoid of ochratoxin-A. Electron beam irradiation dose 10 kGy could be recommended for fungal decontamination and improvement of shelf life of C. maritima ripened dry split beans.

Texture evolution and mechanical behaviour of irradiated face-centred cubic metals

NASA Astrophysics Data System (ADS)

Chen, L. R.; Xiao, X. Z.; Yu, L.; Chu, H. J.; Duan, H. L.

2018-02-01

A physically based theoretical model is proposed to investigate the mechanical behaviour and crystallographic texture evolution of irradiated face-centred cubic metals. This model is capable of capturing the main features of irradiated polycrystalline materials including irradiation hardening, post-yield softening and plasticity localization. Numerical results show a good agreement with experimental data for both unirradiated and irradiated stress-strain relationships. The study of crystallographic texture reveals that the initial randomly distributed texture of unirradiated metals under tensile loading can evolve into a mixture of [111] and [100] textures. Regarding the irradiated case, crystallographic texture develops in a different way, and an extra part of [110] texture evolves into [100] and [111] textures. Thus, [100] and [111] textures become dominant more quickly compared with those of the unirradiated case for the reason that [100] and [111]-oriented crystals have higher strength, and their plastic deformation behaviours are more active than other oriented crystals. It can be concluded that irradiation-induced defects can affect both the mechanical behaviour and texture evolution of metals, both of which are closely related to irradiation hardening.

Heavy-section steel technology program. Semiannual progress report for period ending February 28, 1973

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1974-02-01

The materials investigations under the HSST program are divided into studies of unirradiated materials and studies of irradiation effects. The studies of unirradiated materials, which include inspection, characterization, metallurgy, variability determinations, transition temperature investigations, fracture mechanics studies, and fatigue-crack propagation tests, are discussed. The investigations of irradiated materials include studies of radiation effects on A-533-B steel. Results of studies on thick pressure vessels and pipes of ASTM A508 steel are also reported along with results of studies on Mode III crack extension in reactor piping. (JRD)

The use of unirradiated and γ-irradiated zinc oxide nanoparticles as a preservative in cosmetic preparations

PubMed Central

Hosny, Alaa El-Dien MS; Kashef, Mona T; Taher, Hadeer A; El-Bazza, Zeinab E

2017-01-01

Purpose Microbial contamination of different cosmetic preparations, as a result of preservative failure, presents a major public health threat. Also, most of the known preservatives have serious consumer side effects. The antimicrobial activity of zinc oxide nanoparticles (ZnO NP) is well documented. Therefore, we aimed to determine the possible use of unirradiated and γ-irradiated ZnO NP as a cosmetic preservative. Methods The possible use of ZnO NP as a preservative was tested and compared to commonly used preservatives using a challenge test. Their activity was tested in six different types of preparations. The effect of γ radiation on the antimicrobial activity of ZnO NP was tested through determination of the obtained zone diameters against different microorganisms and the total aerobic microbial count in tested preparations. The antimicrobial activity, of unirradiated and γ-irradiated ZnO NP during storage was also determined. Results ZnO NP were superior to other commonly used preservatives in all tested cosmetic preparations. They pass the challenge test in all types of tested preparations. γ irradiation enhanced their antimicrobial activity in all tested preparations. The irradiation causes a reduction in NP sizes that is directly proportional to the applied radiation dose. Upon storage, ZnO NP were effective in maintaining the microbial count of the product within the acceptable range. Their activity in stored products was enhanced by γ irradiation. Conclusion Unirradiated and γ-irradiated ZnO NP can be used as effective preservatives. They are compatible with the components of all tested products. γ irradiation enhanced the antimicrobial activity of ZnO NP. PMID:28979119

gamma-Irradiation effects on the thermal decomposition behaviour and IR absorption spectra of piperacillin

NASA Astrophysics Data System (ADS)

Mahfouz, R. M.; Gaffar, M. A.; Abu El-Fadl, A.; Hamad, Ar. G. K.

2003-11-01

The thermal decomposition behaviour of unirradiated and pre-gamma-irradiated piperacillin (pipril) as a semi-synthetic penicillin antibiotic has been studied in the temperature range of (273-1072 K). The decomposition was found to proceed through three major steps both for unirradiated and gamma-irradiated samples. Neither appearance nor disappearance of new bands in the IR spectrum of piperacillin was recorded as a result of gamma-irradiation but only a decrease in the intensity of most bands was observed. A degradation mechanism was suggested to explain the bond rupture and the decrease in the intensities of IR bands of gamma-irradiated piperacillin.

Heat treatment effects on toughness of 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated at 365°C

NASA Astrophysics Data System (ADS)

Klueh, R. L.; Alexander, D. J.

1992-09-01

The 9Cr-1MoVNb and 12Cr-1MoVW steels were austenitized at 1040 and 1100°C to produce different prior austenite grain sizes, after which they were given different tempering treatments (1 h at 760°C or 2.5 h at 780°C). Subsize Charpy impact specimens from these materials were irradiated at 365°C up to 5 dpa. For 9Cr-1MoVNb steel in the unirradiated condition, the smaller the prior austenite grain size and the higher the tempering temperature, the lower the ductile-brittle transition temperature (DBTT). Regardless of the DBTT in the unirradiated condition, however, the DBTT shift for 9Cr-1MoVNb steel due to irradiation was the same for all heat treatments. This means heat treatment can be used to ensure a lower DBTT before and after irradiation. The 12Cr-1MoVW steel showed little effect of heat treatment on DBTT in the unirradiated condition, and the shift in DBTT was relatively constant. Thus, it appears that heat treatment cannot be used to reduce the effect of irradiation on DBTT for this steel.

EPR investigation of some traditional oriental irradiated spices

NASA Astrophysics Data System (ADS)

Duliu, Octavian G.; Georgescu, Rodica; Ali, Shaban Ibrahim

2007-06-01

The 9.50 GHz electron paramagnetic resonance (EPR) spectra of unirradiated and 60Co γ-ray irradiated cardamom ( Elettaria cardamomum L. Maton, Zingiberaceae), ginger (( Zingiber officinale Rosc., Zingiberaceae), and saffron ( Crocus sativus L., Iridaceae) have been investigated at room temperature. All unirradiated spices presented a weak resonance line with g-factors around free-electron ones. After γ-ray irradiation at an absorbed dose of up to 11.3 kGy, the presence of EPR spectra whose amplitude increase monotonously with the absorbed dose has been noticed with all spices. A 100 °C isothermal annealing of 11.3 kGy irradiated samples has shown a differential reduction of amplitude of various components that compose initial spectra, but even after 3.6 h of thermal treatment, the remaining amplitude represents no less then 30% of the initial ones. The same peculiarities have been noticed after 83 days storage at room temperature but after 340 days storage at ambient conditions only irradiated ginger displays a weak signal that differs from those of unirradiated sample. All these factors could be taken into account in establishing at which extent the EPR is suitable to evidence any irradiation treatment applied to these spices.

Spatially Fractionated Radiation Induces Cytotoxicity and Changes in Gene Expression in Bystander and Radiation Adjacent Murine Carcinoma Cells

PubMed Central

Asur, Rajalakshmi S.; Sharma, Sunil; Chang, Ching-Wei; Penagaricano, Jose; Kommuru, Indira M.; Moros, Eduardo G.; Corry, Peter M.; Griffin, Robert J.

2012-01-01

Radiation-induced bystander effects have been extensively studied at low doses, since evidence of bystander induced cell killing and other effects on unirradiated cells were found to be predominant at doses up to 0.5 Gy. Therefore, few studies have examined bystander effects induced by exposure to higher doses of radiation, such as spatially fractionated radiation (GRID) treatment. In the present study, we evaluate the ability of GRID treatment to induce changes in GRID adjacent (bystander) regions, in two different murine carcinoma cell lines following exposure to a single irradiation dose of 10 Gy. Murine SCK mammary carcinoma cells and SCCVII squamous carcinoma cells were irradiated using a brass collimator to create a GRID pattern of nine circular fields 12 mm in diameter with a center-to-center distance of 18 mm. Similar to the typical clinical implementation of GRID, this is approximately a 50:50 ratio of direct and bystander exposure. We also performed experiments by irradiating separate cultures and transferring the medium to unirradiated bystander cultures. Clonogenic survival was evaluated in both cell lines to determine the occurrence of radiation-induced bystander effects. For the purpose of our study, we have defined bystander cells as GRID adjacent cells that received approximately 1 Gy scatter dose or unirradiated cells receiving conditioned medium from irradiated cells. We observed significant bystander killing of cells adjacent to the GRID irradiated regions compared to sham treated controls. We also observed bystander killing of SCK and SCCVII cells cultured in conditioned medium obtained from cells irradiated with 10 Gy. Therefore, our results confirm the occurrence of bystander effects following exposure to a high-dose of radiation and suggest that cell-to-cell contact is not required for these effects. In addition, the gene expression profile for DNA damage and cellular stress response signaling in SCCVII cells after GRID exposure was studied. The occurrence of GRID-induced bystander gene expression changes in significant numbers of DNA damage and cellular stress response signaling genes, providing molecular evidence for possible mechanisms of bystander cell killing. PMID:22559204

Quasipermanent magnets of high temperature superconductor - Temperature dependence

NASA Technical Reports Server (NTRS)

Chen, In-Gann; Liu, Jianxiong; Ren, Yanru; Weinstein, Roy; Kozlowski, Gregory; Oberly, Charles E.

1993-01-01

We report on persistent field in quasi-permanent magnets of high temperature superconductors. Magnets composed of irradiated Y(1+)Ba2Cu3O7 trapped field Bt = 1.52 T at 77 K and 1.9 T at lower temperature. However, the activation magnet limited Bt at lower temperature. We present data on Jc(H,T) for unirradiated materials, and calculate Bt at various T. Based upon data at 65 K, we calculate Bt in unirradiated single grains at 20 K and find that 5.2 T will be trapped for grain diameter d about 1.2 cm, and 7.9 T for d = 2.3 cm. Irradiated grains will trap four times these values.

The effect of ion irradiation on the dissolution of UO 2 and UO 2 -based simulant fuel

DOE PAGES

Popel, Aleksej J.; Wietsma, Thomas W.; Engelhard, Mark H.; ...

2017-11-21

Our aim is to study the separate effect of fission fragment damage on the dissolution of simulant UK advanced gas-cooled reactor nuclear fuel in water. Plain UO 2 and UO 2 samples, doped with inactive fission products to simulate 43 GWd/tU of burn-up, were fabricated. A set of these samples were then irradiated with 92 MeV 129Xe 23+ ions to a fluence of 4.8 × 10 15 ions/cm 2 to simulate the fission damage that occurs within nuclear fuels. The primary effect of the irradiation on the UO 2 samples, observed by scanning electron microscopy, was to induce a smootheningmore » of the surface features and formation of hollow blisters, which was attributed to multiple overlap of ion tracks. Dissolution experiments were conducted in single-pass flow-through (SPFT) mode under anoxic conditions (<0.1 O 2 ppm in Ar) to study the effect of the induced irradiation damage on the dissolution of the UO 2 matrix with data collection capturing six minute intervals for several hours. These time-resolved data showed that the irradiated samples showed a higher initial release of uranium than unirradiated samples, but that the uranium concentrations converged towards ~10 -9 mol/l after a few hours. And apart from the initial spike in uranium concentration, attributed to irradiation induced surficial micro-structural changes, no noticeable difference in uranium chemistry as measured by X-ray electron spectroscopy or ‘effective solubility’ was observed between the irradiated, doped and undoped samples in this work. Some secondary phase formation was observed on the surface of UO 2 samples after the dissolution experiment.« less

The effect of ion irradiation on the dissolution of UO 2 and UO 2 -based simulant fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popel, Aleksej J.; Wietsma, Thomas W.; Engelhard, Mark H.

Our aim is to study the separate effect of fission fragment damage on the dissolution of simulant UK advanced gas-cooled reactor nuclear fuel in water. Plain UO 2 and UO 2 samples, doped with inactive fission products to simulate 43 GWd/tU of burn-up, were fabricated. A set of these samples were then irradiated with 92 MeV 129Xe 23+ ions to a fluence of 4.8 × 10 15 ions/cm 2 to simulate the fission damage that occurs within nuclear fuels. The primary effect of the irradiation on the UO 2 samples, observed by scanning electron microscopy, was to induce a smootheningmore » of the surface features and formation of hollow blisters, which was attributed to multiple overlap of ion tracks. Dissolution experiments were conducted in single-pass flow-through (SPFT) mode under anoxic conditions (<0.1 O 2 ppm in Ar) to study the effect of the induced irradiation damage on the dissolution of the UO 2 matrix with data collection capturing six minute intervals for several hours. These time-resolved data showed that the irradiated samples showed a higher initial release of uranium than unirradiated samples, but that the uranium concentrations converged towards ~10 -9 mol/l after a few hours. And apart from the initial spike in uranium concentration, attributed to irradiation induced surficial micro-structural changes, no noticeable difference in uranium chemistry as measured by X-ray electron spectroscopy or ‘effective solubility’ was observed between the irradiated, doped and undoped samples in this work. Some secondary phase formation was observed on the surface of UO 2 samples after the dissolution experiment.« less

Investigation of gamma radiation induced changes in local structure of borosilicate glass by TDPAC and EXAFS

NASA Astrophysics Data System (ADS)

Kumar, Ashwani; Nayak, C.; Rajput, P.; Mishra, R. K.; Bhattacharyya, D.; Kaushik, C. P.; Tomar, B. S.

2016-12-01

Gamma radiation induced changes in local structure around the probe atom (Hafnium) were investigated in sodium barium borosilicate (NBS) glass, used for immobilization of high level liquid waste generated from the reprocessing plant at Trombay, Mumbai. The (NBS) glass was doped with 181Hf as a probe for time differential perturbed angular correlation (TDPAC) spectroscopy studies, while for studies using extended X-ray absorption fine structure (EXAFS) spectroscopy, the same was doped with 0.5 and 2 % (mole %) hafnium oxide. The irradiated as well as un-irradiated glass samples were studied by TDPAC and EXAFS techniques to obtain information about the changes (if any) around the probe atom due to gamma irradiation. TDPAC spectra of unirradiated and irradiated glasses were similar and reminescent of amorphous materials, indicating negligible effect of gamma radiation on the microstructure around Hafnium probe atom, though the quaqdrupole interaction frequency ( ω Q) and asymmetry parameter ( η) did show a marginal decrease in the irradiated glass compared to that in the unirradiated glass. EXAFS measurements showed a slight decrease in the Hf-O bond distance upon gamma irradiation of Hf doped NBS glass indicating densification of the glass matrix, while the cordination number around hafnium remains unchanged.

Fracture mechanism maps in unirradiated and irradiated metals and alloys

NASA Astrophysics Data System (ADS)

Li, Meimei; Zinkle, S. J.

2007-04-01

This paper presents a methodology for computing a fracture mechanism map in two-dimensional space of tensile stress and temperature using physically-based constitutive equations. Four principal fracture mechanisms were considered: cleavage fracture, low temperature ductile fracture, transgranular creep fracture, and intergranular creep fracture. The methodology was applied to calculate fracture mechanism maps for several selected reactor materials, CuCrZr, 316 type stainless steel, F82H ferritic-martensitic steel, V4Cr4Ti and Mo. The calculated fracture maps are in good agreement with empirical maps obtained from experimental observations. The fracture mechanism maps of unirradiated metals and alloys were modified to include radiation hardening effects on cleavage fracture and high temperature helium embrittlement. Future refinement of fracture mechanism maps is discussed.

Enhanced mutagenesis parallels enhanced reactivation of herpes virus in a human cell line.

PubMed Central

Lytle, C D; Knott, D C

1982-01-01

U.v. irradiation of human NB-E cells results in enhanced mutagenesis and enhanced reactivation of u.v.-irradiated H-1 virus grown in those cells ( Cornelis et al., 1982). This paper reports a similar study using herpes simplex virus (HSV) in NB-E cells. The mutation frequency of HSV (resistance of virus plaque formation to 40 micrograms/ml iododeoxycytidine ) increased approximately linearly with exposure of the virus to u.v. radiation. HSV grown in unirradiated cells gave a slope of 1.8 X 10(-5)m2/J, with 3.2 X 10(-5)m2/J for HSV grown in cells irradiated (3 J/m2) 24 h before infection. There was no evidence for mutagenesis of unirradiated virus by irradiated cells, as seen with H-1 virus. Enhanced reactivation of irradiated HSV in parallel cultures increased virus survival, manifested as a change in slope of the final component of the two-component survival curve from a D0 of 27 J/m2 in unirradiated cells to 45 J/m2 in irradiated cells. Thus, enhanced mutagenesis and enhanced reactivation occurred for irradiated HSV in NB-E cells. The difference in the enhanced mutagenesis of HSV (dependent on damaged DNA sites) and of H-1 virus (primarily independent of damaged DNA sites) is discussed in terms of differences in DNA polymerases. PMID:6329698

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henager, Jr., C. H.; Nguyen, Ba N.; Kurtz, Richard J.

The international fusion community has designed a miniature torsion specimen for neutron irradiation studies of joined SiC and SiC/SiC composite materials. For this research, miniature torsion joints based on this specimen design were fabricated using displacement reactions between Si and TiC to produce Ti 3SiC 2 + SiC joints with SiC and tested in torsion-shear prior to and after neutron irradiation. However, many miniature torsion specimens fail out-of-plane within the SiC specimen body, which makes it problematic to assign a shear strength value to the joints and makes it difficult to compare unirradiated and irradiated strengths to determine irradiation effects.more » Finite element elastic damage and elastic–plastic damage models of miniature torsion joints are developed that indicate shear fracture is more likely to occur within the body of the joined sample and cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The model results are compared and discussed with regard to unirradiated and irradiated test data for a variety of joint materials. The unirradiated data includes Ti 3SiC 2 + SiC/CVD-SiC joints with tailored joint moduli, and includes steel/epoxy and CVD-SiC/epoxy joints. Finally, the implications for joint data based on this sample design are discussed.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henager, Charles H.; Nguyen, Ba Nghiep; Kurtz, Richard J.

The international fusion community has designed a miniature torsion specimen for neutron irradiation studies of joined SiC and SiC/SiC composite materials. Miniature torsion joints based on this specimen design were fabricated using displacement reactions between Si and TiC to produce Ti3SiC2 + SiC joints with CVD-SiC and tested in torsion-shear prior to and after neutron irradiation. However, many of these miniature torsion specimens fail out-of-plane within the CVD-SiC specimen body, which makes it problematic to assign a shear strength value to the joints and makes it difficult to compare unirradiated and irradiated joint strengths to determine the effects of themore » irradiation. Finite element elastic damage and elastic-plastic damage models of miniature torsion joints are developed that indicate shear fracture is likely to occur within the body of the joined sample and cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The model results are compared and discussed with regard to unirradiated and irradiated joint test data for a variety of joint materials. The unirradiated data includes Ti3SiC2 + SiC/CVD-SiC joints with tailored joint moduli, and includes steel/epoxy and CVD-SiC/epoxy joints. The implications for joint data based on this sample design are discussed.« less

40 CFR 80.581 - What are the batch testing and sample retention requirements for motor vehicle diesel fuel, NRLM...

Code of Federal Regulations, 2011 CFR

2011-07-01

... retention requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? 80.581 Section...) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel... requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? (a) Beginning on June 1...

40 CFR 80.581 - What are the batch testing and sample retention requirements for motor vehicle diesel fuel, NRLM...

Code of Federal Regulations, 2010 CFR

2010-07-01

... retention requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? 80.581 Section...) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel... requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? (a) Beginning on June 1...

An electron spin resonance study of some gamma-irradiated fruits

NASA Astrophysics Data System (ADS)

Maloney, Darren R.; Tabner, Brian J.; Tabner, Vivienne A.

The ESR spectra of the seeds, skins and stalks of unirradiated and γ-irradiated Chilean white grapes have been obtained and the results compared to those previously reported for Cape black grapes. The high degree of reproducibility of the spectra obtained from the stalks of different varieties of grapes suggest that ESR spectroscopy could form the basis of a viable test to determine their irradiation history. The condition of the stalk prior to irradiation has been found to have little effect on the resulting spectra. The spectra from the stalks, skins and seeds of unirradiated and γ-irradiated apples, peers and cherries have also been examined. Although most of the spectra from irradiated components exhibit extra features, they are sometimes short-lived and restrict the development of ESR as a viable test.

Effect of ultrasonic irradiation on mammalian cells and chromosomes in vitro

NASA Technical Reports Server (NTRS)

Roseboro, J. A.; Buchanan, P.; Norman, A.; Stern, R.

1978-01-01

Human peripheral blood and HeLa cells were irradiated in vitro at the ultrasonic frequency of 65 kHz. The whole blood and HeLa cell suspensions were exposed to continuous and pulsed ultrasonic power levels of 0.12, 0.16, 0.72, 1.12 and 2.24 W for a period of one minute. The method of ultrasonic irradiation was carried out with the whole blood or HeLa cell suspensions coupled directly to a cylindrical transducer while heating of the cell suspensions in excess of 41 C was avoided. Irradiated and unirradiated peripheral blood lymphocyte chromosome cultures were prepared and scored for selected numerical and morphological aberrations. There was no significant difference in the frequency of chromosomal aberrations between irradiated and unirradiated cells.

40 CFR 600.304-12 - Fuel economy label-special requirements for hydrogen fuel cell vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for hydrogen fuel cell vehicles. 600.304-12 Section 600.304-12 Protection of Environment... MOTOR VEHICLES Fuel Economy Labeling § 600.304-12 Fuel economy label—special requirements for hydrogen fuel cell vehicles. Fuel economy labels for hydrogen fuel cell vehicles must meet the specifications...

40 CFR 600.304-12 - Fuel economy label-special requirements for hydrogen fuel cell vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for hydrogen fuel cell vehicles. 600.304-12 Section 600.304-12 Protection of Environment... MOTOR VEHICLES Fuel Economy Labeling § 600.304-12 Fuel economy label—special requirements for hydrogen fuel cell vehicles. Fuel economy labels for hydrogen fuel cell vehicles must meet the specifications...

40 CFR 600.304-12 - Fuel economy label-special requirements for hydrogen fuel cell vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for hydrogen fuel cell vehicles. 600.304-12 Section 600.304-12 Protection of Environment... MOTOR VEHICLES Fuel Economy Labeling § 600.304-12 Fuel economy label—special requirements for hydrogen fuel cell vehicles. Fuel economy labels for hydrogen fuel cell vehicles must meet the specifications...

40 CFR 80.594 - What are the pre-compliance reporting requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for motor vehicle diesel fuel? 80.594 Section 80.594 Protection of Environment ENVIRONMENTAL... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Recordkeeping and Reporting Requirements § 80.594 What are the pre-compliance reporting requirements for motor vehicle diesel fuel? (a...

40 CFR 80.594 - What are the pre-compliance reporting requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for motor vehicle diesel fuel? 80.594 Section 80.594 Protection of Environment ENVIRONMENTAL... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Recordkeeping and Reporting Requirements § 80.594 What are the pre-compliance reporting requirements for motor vehicle diesel fuel? (a...

40 CFR 80.608 - What requirements apply to diesel fuel and ECA marine fuel for use in the Territories?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false What requirements apply to diesel fuel... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Exemptions § 80.608 What requirements apply to diesel fuel and ECA marine fuel for use in the Territories? The...

40 CFR 80.608 - What requirements apply to diesel fuel and ECA marine fuel for use in the Territories?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false What requirements apply to diesel fuel... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Exemptions § 80.608 What requirements apply to diesel fuel and ECA marine fuel for use in the Territories? The...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weaver, Jordan S.; Pathak, Siddhartha; Reichardt, Ashley

Experimentally quantifying the mechanical effects of radiation damage in reactor materials is necessary for the development and qualification of new materials for improved performance and safety. This can be achieved in a high-throughput fashion through a combination of ion beam irradiation and small scale mechanical testing in contrast to the high cost and laborious nature of bulk testing of reactor irradiated samples. The current paper focuses on using spherical nanoindentation stress-strain curves on unirradiated and proton irradiated (10 dpa at 360 °C) 304 stainless steel to quantify the mechanical effects of radiation damage. Spherical nanoindentation stress-strain measurements show a radiation-inducedmore » increase in indentation yield strength from 1.36 GPa to 2.72 GPa and a radiation-induced increase in indentation work hardening rate of 10 GPa–30 GPa. These measurements are critically compared against Berkovich nanohardness, micropillar compression, and micro-tension measurements on the same material and similar grain orientations. The ratio of irradiated to unirradiated yield strength increases by a similar factor of 2 when measured via spherical nanoindentation or Berkovich nanohardness testing. A comparison of spherical indentation stress-strain curves to uniaxial (micropillar and micro-tension) stress-strain curves was achieved using a simple scaling relationship which shows good agreement for the unirradiated condition and poor agreement in post-yield behavior for the irradiated condition. Finally, the disagreement between spherical nanoindentation and uniaxial stress-strain curves is likely due to the plastic instability that occurs during uniaxial tests but is absent during spherical nanoindentation tests.« less

In situ high-energy X-ray diffraction study of tensile deformation of neutron-irradiated polycrystalline Fe-9%Cr alloy

DOE PAGES

Zhang, Xuan; Li, Meimei; Park, Jun -Sang; ...

2016-12-30

The effect of neutron irradiation on tensile deformation of a Fe-9wt.%Cr alloy was investigated using in situ high-energy synchrotron X-ray diffraction during room-temperature uniaxial tensile tests. New insights into the deformation mechanisms were obtained through the measurements of lattice strain evolution and the analysis of diffraction peak broadening using the modified Williamson-Hall method. Two neutron-irradiated specimens, one irradiated at 300 °C to 0.01 dpa and the other at 450 °C to 0.01dpa, were tested along with an unirradiated specimen. The macroscopic stress–strain curves of the irradiated specimens showed increased strength, reduced ductility and work-hardening exponent compared to the unirradiated specimen.more » The evolutions of the lattice strain, the dislocation density and the coherent scattering domain size in the deformation process revealed different roles of the submicroscopic defects in the 300°C/0.01 dpa specimen and the TEM-visible nanometer-sized dislocation loops in the 450°C/0.01 dpa specimen: submicroscopic defects extended the linear work hardening stage (stage II) to a higher strain, while irradiation-induced dislocation loops were more effective in dislocation pinning. Lastly, while the work hardening rate of stage II was unaffected by irradiation, significant dynamic recovery in stage III in the irradiated specimens led to the early onset of necking without stage IV as observed in the unirradiated specimen.« less

Modeling and testing miniature torsion specimens for SiC joining development studies for fusion

DOE PAGES

Henager, Jr., C. H.; Nguyen, Ba N.; Kurtz, Richard J.; ...

2015-08-05

The international fusion community has designed a miniature torsion specimen for neutron irradiation studies of joined SiC and SiC/SiC composite materials. For this research, miniature torsion joints based on this specimen design were fabricated using displacement reactions between Si and TiC to produce Ti 3SiC 2 + SiC joints with SiC and tested in torsion-shear prior to and after neutron irradiation. However, many miniature torsion specimens fail out-of-plane within the SiC specimen body, which makes it problematic to assign a shear strength value to the joints and makes it difficult to compare unirradiated and irradiated strengths to determine irradiation effects.more » Finite element elastic damage and elastic–plastic damage models of miniature torsion joints are developed that indicate shear fracture is more likely to occur within the body of the joined sample and cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The model results are compared and discussed with regard to unirradiated and irradiated test data for a variety of joint materials. The unirradiated data includes Ti 3SiC 2 + SiC/CVD-SiC joints with tailored joint moduli, and includes steel/epoxy and CVD-SiC/epoxy joints. Finally, the implications for joint data based on this sample design are discussed.« less

Modification of radiation carcinogenesis by marihuana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montour, J.L.; Dutz, W.; Harris, L.S.

1981-03-15

Male, female, and ovariectomized female Sprague-Dawley rats were irradiated with 400 rads, 150 rads, or 300 rads, respectively, of /sup 60/Co gamma rays when they were between 40 and 50 days of age. The animals were injected three times weekly with either marihuana extract or with alcohol-emulphor carrier. Comparable unirradiated groups were similarly injected. Mean survival time in males was significantly shorter in the 400 rad + marihuana group compared with the three other groups whose mean survival times did not differ. Through the 546 days that the males were observed, the total number of tumors other than fibrosarcomas wasmore » significantly greater following radiation and marihuana (22) than radiation alone (6). Fifteen of the tumors were of breast or endocrine tissues. No differences were seen in the unirradiated groups. In the females, which were observed for 635 days, the total number of breast tumors was greater with the combined treatment (38) compared with radiation alone (22). This was entirely due to a marked difference in the adenocarcinoma incidence, which was 21 (radiation + marihuana) compared with four (radiation alone). The number of adenofibromas was similar in the two groups. In the unirradiated female groups the breast adenocarcinoma incidence was eight in the marihuana group and two in the control group. Ovariectomy resulted in a lower breast tumor incidence in all groups. Nonbreast tumors were more frequent in the ovariectomized-irradiated groups. Radiation plus marihuana produced more nonbreast tumors (25) than radiation alone (17) in the ovariectomized females.« less

Modification of radiation carcinogenesis by marijuana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montour, J.L.; Dutz, W.; Harris, L.S.

Male, female, and ovariectomized female Sprague-Dawley rats were irradiated with 400 rads, 150 rads, or 300 rads, respectively, of /sup 60/Co gamma rays when they were between 40 and 50 days of age. The animals were injected three times weekly with either marihuana extract or with alcohol-emulphor carrier. Comparable unirradiated groups were similarly injected. Mean survival time in males was significantly shorter in the 400 rad + marihuana group compared with the three other groups whose mean survival times did not differ. Through the 546 days that the males were observed, the total number of tumors other than fibrosarcomas wasmore » significantly greater following radiation and marihuana (22) than radiation alone (6). Fifteen of the tumors were of breast or endocrine tissues. No differences were seen in the unirradiated groups. In the females, which were observed for 635 days, the total number of breast tumors was greater with the combined treatment (38) compared with radiation alone (22). This was entirely due to a marked difference in the adenocarcinoma incidence, which was 21 (radiation + marihuana) compared with four (radiation alone). The number of adenofibromas was similar in the two groups. In the unirradiated female groups the breast adenocarcinoma incidence was eight in the marihuana group and two in the control group. Ovariectomy resulted in a lower breast tumor incidence in all groups. Nonbreast tumors were more frequent in the ovariectomized-irradiated groups. Radiation plus marihuana produced more nonbreast tumors (25) than radiation alone (17) in the ovariectomized females.« less

40 CFR Table 5 to Subpart Jjjjjj... - Fuel Analysis Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 15 2012-07-01 2012-07-01 false Fuel Analysis Requirements 5 Table 5... Part 63—Fuel Analysis Requirements As stated in § 63.11213, you must comply with the following requirements for fuel analysis testing for affected sources: To conduct a fuel analysis for the following...

Processing Plan for Potentially Reactive/Ignitable Remote Handled Transuranic Waste at the Idaho Cleanup Project - 12090

DOE Office of Scientific and Technical Information (OSTI.GOV)

Troescher, Patrick D.; Hobbes, Tammy L.; Anderson, Scott A.

Remote Handle Transuranic (RH-TRU) Waste generated at Argonne National Laboratory - East, from the examination of irradiated and un-irradiated fuel pins and other reactor materials requires a detailed processing plan to ensure reactive/ignitable material is absent to meet WIPP Waste Acceptance Criteria prior to shipping and disposal. The Idaho Cleanup Project (ICP) approach to repackaging Lot 2 waste and how we ensure prohibited materials are not present in waste intended for disposal at Waste Isolation Pilot Plant 'WIPP' uses an Argon Repackaging Station (ARS), which provides an inert gas blanket. Opening of the Lot 2 containers under an argon gasmore » blanket is proposed to be completed in the ARS. The ARS is an interim transition repackaging station that provides a mitigation technique to reduce the chances of a reoccurrence of a thermal event prior to rendering the waste 'Safe'. The consequences, should another thermal event be encountered, (which is likely) is to package the waste, apply the reactive and or ignitable codes to the container, and store until the future treatment permit and process are available. This is the same disposition that the two earlier containers in the 'Thermal Events' were assigned. By performing the initial handling under an inert gas blanket, the waste can sorted and segregate the fines and add the Met-L-X to minimize risk before it is exposed to air. The 1-gal cans that are inside the ANL-E canister will be removed and each can is moved to the ARS for repackaging. In the ARS, the 1-gal can is opened in the inerted environment. The contained waste is sorted, weighed, and visually examined for non compliant items such as unvented aerosol cans and liquids. The contents of the paint cans are transferred into a sieve and manipulated to allow the fines, if any, to be separated into the tray below. The fines are weighed and then blended with a minimum 5:1 mix of Met-L-X. Other debris materials found are segregated from the cans into containers for later packaging. Recoverable fissile waste material (Fuel and fuel-like pieces) suspected of containing sodium bonded pieces) are segregated and will remain in the sieve or transferred to a similar immersion basket in the ARS. The fuel like pieces will be placed into a container with sufficient water to cover the recoverable fissile waste. If a 'reactive characteristic' is present the operator will be able to observe the formation of 'violent' hydrogen gas bubbles. When sodium bonded fuel-like pieces are placed in water the expected reaction is a non-violent reaction that does not meet the definition of reactivity. It is expected that there will be a visible small stream of bubbles present if there is any sodium-bonded fuel-like piece placed in the water. The test will be completed when there is no reaction or the expected reaction is observed..At that point, the fuel like pieces complete the processing cycle in preparation for characterization and shipment to WIPP. If a violent reaction occurs, the fuel-like pieces will be removed from the water, split into the required fissile material content, placed into a screened basket in a 1 gallon drum and drummed out of the hot cell with appropriate RCRA codes applied and placed into storage until sodium treatment is available. These 'violent' reactions will be evidenced by gas bubbles being evolved at the specimen surface where sodium metal is present. The operators will be trained to determine if the reaction is 'violent' or 'mild'. If a 'violent' reaction occurs, the sieve will be immediately removed from the water, placed in a 1 gallon paint can, canned in the argon cover gas and removed from the hot cell to await a future treatment. If the reaction is 'mild', the sieve will then be removed from the water; the material weighed for final packaging and allowed to dry by air exposure. Lot 2 waste cans can be opened, sorted, processed, and weighed while mitigating the potential of thermal events that could occur prior to exposing to air. Exposure to air is a WIPP compliance step demonstrating the absence of reactive or ignitable characteristics. (authors)« less

Performance and breakdown characteristics of irradiated vertical power GaN P-i-N diodes

DOE PAGES

King, M. P.; Armstrong, A. M.; Dickerson, J. R.; ...

2015-10-29

Electrical performance and defect characterization of vertical GaN P-i-N diodes before and after irradiation with 2.5 MeV protons and neutrons is investigated. Devices exhibit increase in specific on-resistance following irradiation with protons and neutrons, indicating displacement damage introduces defects into the p-GaN and n- drift regions of the device that impact on-state device performance. The breakdown voltage of these devices, initially above 1700 V, is observed to decrease only slightly for particle fluence <; 10 13 cm -2. Furthermore, the unipolar figure of merit for power devices indicates that while the on-resistance and breakdown voltage degrade with irradiation, vertical GaNmore » P-i-Ns remain superior to the performance of the best available, unirradiated silicon devices and on-par with unirradiated modern SiC-based power devices.« less

Application of DNA comet assay for detection of radiation treatment of grams and pulses.

PubMed

Khan, Hasan M; Khan, Ashfaq A; Khan, Sanaullah

2011-12-01

Several types of whole pulses (green lentils, red lentils, yellow lentils, chickpeas, green peas, cowpeas and yellow peas) and grams (black grams, red grams and white grams) have been investigated for the identification of radiation treatment using microgel electrophoresis of single cells (DNA comet assay). Pulses and grams were exposed to the radiation doses of 0.5, 1.0 and 5 kGy covering the legalized commercial dose range for protection from insect/pest infestations. All irradiated samples showed comet like stretching of fragmented DNA toward anode, which is expected for irradiated samples. Unirradiated samples showed many intact cells/nuclei in form of round stains or with short faint tails, which is typical for unirradiated food samples. The study shows that DNA comet assay can be used as a rapid, inexpensive and highly effective screening test for the detection of radiation treatment of foods, like pulses and grams.

Comparative viability of unirradiated and gamma irradiated bacterial cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maxcy, R.B.

1977-01-01

Gamma radiation injured Escherichia coli, Salmonella typhimurium, and Moraxella sp. were studied under various environmental stresses to determine their fate relative to the parent population. Irradiated cultures formed smaller colonies on surface plates with fewer cells per colony. Unirradiated cultures had a shorter lag phase than irradiated cultures in broth and duration of lag increased as a result of increasing the radiation dose. Repeated irradiation and subculture progressively retarded growth rate. Multiple radiation of highly resistant Moraxella sp. showed radiation injured cells to be more sensitive than uninjured cells. With the three species studied, irradiation raised the lower limits ofmore » growth temperature, increased the sensitivity to freezing and thawing, and increased the susceptibility to lowered water activity. This work indicated that the production of a bizarre, resistant strain of bacteria through recycling in a food processing operation is highly unlikely.« less

Proton irradiation studies on Al and Al5083 alloy

NASA Astrophysics Data System (ADS)

Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

2017-10-01

The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

Electrical and thermoluminescence properties of γ-irradiated La2CuO4 crystals

NASA Astrophysics Data System (ADS)

El-Kolaly, M. A.; Abd El-Kader, H. I.; Kassem, M. E.

1994-12-01

Measurements of the electrical properties of unirradiated as well as ?-irradiated La2CuO4 crystals were carried out at different temperatures in the frequency range of 0.1-100 kHz. Thermoluminescence (TL) studies were also performed on such crystals in the temperature range of 300-600K. The conductivity of the unirradiated La2CuO4 crystals were found to obey the power law frequency dependence at each measured temperature below the transition temperature (Tc = 450K). The activation energies for conduction and dielectric relaxation time have been calculated. The TL response and the dc resistance were found to increase with ?-irradiation dose up to 9-10 kGy. The results showed that the ferroelastic domain walls of La2CuO4 crystal as well as its TL traps are sensitive to ?-raditaion. This material can be used in radiation measurements in the range 225 Gy-10 kGy.

40 CFR 85.1510 - Maintenance instructions, warranties, emission labeling and fuel economy requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., emission labeling and fuel economy requirements. 85.1510 Section 85.1510 Protection of Environment..., warranties, emission labeling and fuel economy requirements. The provisions of this section are applicable to... for final admission. (d) Fuel economy labeling. (1) The certificate holder shall affix a fuel economy...

40 CFR 85.1510 - Maintenance instructions, warranties, emission labeling and fuel economy requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., emission labeling and fuel economy requirements. 85.1510 Section 85.1510 Protection of Environment..., warranties, emission labeling and fuel economy requirements. The provisions of this section are applicable to... for final admission. (d) Fuel economy labeling. (1) The certificate holder shall affix a fuel economy...

40 CFR 85.1510 - Maintenance instructions, warranties, emission labeling and fuel economy requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., emission labeling and fuel economy requirements. 85.1510 Section 85.1510 Protection of Environment..., warranties, emission labeling and fuel economy requirements. The provisions of this section are applicable to... for final admission. (d) Fuel economy labeling. (1) The certificate holder shall affix a fuel economy...

40 CFR 80.521 - What are the standards and identification requirements for diesel fuel additives?

Code of Federal Regulations, 2014 CFR

2014-07-01

... identification requirements for diesel fuel additives? 80.521 Section 80.521 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... requirements for diesel fuel additives? (a) Except as provided in paragraph (b) of this section, any diesel...

40 CFR 80.521 - What are the standards and identification requirements for diesel fuel additives?

Code of Federal Regulations, 2011 CFR

2011-07-01

... identification requirements for diesel fuel additives? 80.521 Section 80.521 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... requirements for diesel fuel additives? (a) Except as provided in paragraph (b) of this section, any diesel...

40 CFR 80.521 - What are the standards and identification requirements for diesel fuel additives?

Code of Federal Regulations, 2013 CFR

2013-07-01

... identification requirements for diesel fuel additives? 80.521 Section 80.521 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... requirements for diesel fuel additives? (a) Except as provided in paragraph (b) of this section, any diesel...

40 CFR 80.521 - What are the standards and identification requirements for diesel fuel additives?

Code of Federal Regulations, 2010 CFR

2010-07-01

... identification requirements for diesel fuel additives? 80.521 Section 80.521 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... requirements for diesel fuel additives? (a) Except as provided in paragraph (b) of this section, any diesel...

40 CFR 80.521 - What are the standards and identification requirements for diesel fuel additives?

Code of Federal Regulations, 2012 CFR

2012-07-01

... identification requirements for diesel fuel additives? 80.521 Section 80.521 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... requirements for diesel fuel additives? (a) Except as provided in paragraph (b) of this section, any diesel...

10 CFR 503.23 - Inability to comply with applicable environmental requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... requirements. 503.23 Section 503.23 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES... operating an alternate fuel fired facility in compliance with applicable environmental requirements. (b... the proposed fuel and the alternate fuel(s) which would provide the basis for exemption. All such...

41 CFR 102-34.40 - Who must comply with motor vehicle fuel efficiency requirements?

Code of Federal Regulations, 2011 CFR

2011-01-01

... motor vehicle fuel efficiency requirements? 102-34.40 Section 102-34.40 Public Contracts and Property... with motor vehicle fuel efficiency requirements? (a) Executive agencies operating domestic fleets must comply with motor vehicle fuel efficiency requirements for such fleets. (b) This subpart does not apply...

Spherical nanoindentation of proton irradiated 304 stainless steel: A comparison of small scale mechanical test techniques for measuring irradiation hardening

DOE PAGES

Weaver, Jordan S.; Pathak, Siddhartha; Reichardt, Ashley; ...

2017-06-27

Experimentally quantifying the mechanical effects of radiation damage in reactor materials is necessary for the development and qualification of new materials for improved performance and safety. This can be achieved in a high-throughput fashion through a combination of ion beam irradiation and small scale mechanical testing in contrast to the high cost and laborious nature of bulk testing of reactor irradiated samples. The current paper focuses on using spherical nanoindentation stress-strain curves on unirradiated and proton irradiated (10 dpa at 360 °C) 304 stainless steel to quantify the mechanical effects of radiation damage. Spherical nanoindentation stress-strain measurements show a radiation-inducedmore » increase in indentation yield strength from 1.36 GPa to 2.72 GPa and a radiation-induced increase in indentation work hardening rate of 10 GPa–30 GPa. These measurements are critically compared against Berkovich nanohardness, micropillar compression, and micro-tension measurements on the same material and similar grain orientations. The ratio of irradiated to unirradiated yield strength increases by a similar factor of 2 when measured via spherical nanoindentation or Berkovich nanohardness testing. A comparison of spherical indentation stress-strain curves to uniaxial (micropillar and micro-tension) stress-strain curves was achieved using a simple scaling relationship which shows good agreement for the unirradiated condition and poor agreement in post-yield behavior for the irradiated condition. Finally, the disagreement between spherical nanoindentation and uniaxial stress-strain curves is likely due to the plastic instability that occurs during uniaxial tests but is absent during spherical nanoindentation tests.« less

Spherical nanoindentation of proton irradiated 304 stainless steel: A comparison of small scale mechanical test techniques for measuring irradiation hardening

NASA Astrophysics Data System (ADS)

Weaver, Jordan S.; Pathak, Siddhartha; Reichardt, Ashley; Vo, Hi T.; Maloy, Stuart A.; Hosemann, Peter; Mara, Nathan A.

2017-09-01

Experimentally quantifying the mechanical effects of radiation damage in reactor materials is necessary for the development and qualification of new materials for improved performance and safety. This can be achieved in a high-throughput fashion through a combination of ion beam irradiation and small scale mechanical testing in contrast to the high cost and laborious nature of bulk testing of reactor irradiated samples. The current work focuses on using spherical nanoindentation stress-strain curves on unirradiated and proton irradiated (10 dpa at 360 °C) 304 stainless steel to quantify the mechanical effects of radiation damage. Spherical nanoindentation stress-strain measurements show a radiation-induced increase in indentation yield strength from 1.36 GPa to 2.72 GPa and a radiation-induced increase in indentation work hardening rate of 10 GPa-30 GPa. These measurements are critically compared against Berkovich nanohardness, micropillar compression, and micro-tension measurements on the same material and similar grain orientations. The ratio of irradiated to unirradiated yield strength increases by a similar factor of 2 when measured via spherical nanoindentation or Berkovich nanohardness testing. A comparison of spherical indentation stress-strain curves to uniaxial (micropillar and micro-tension) stress-strain curves was achieved using a simple scaling relationship which shows good agreement for the unirradiated condition and poor agreement in post-yield behavior for the irradiated condition. The disagreement between spherical nanoindentation and uniaxial stress-strain curves is likely due to the plastic instability that occurs during uniaxial tests but is absent during spherical nanoindentation tests.

Mating competitiveness of male Anopheles arabiensis mosquitoes irradiated with a partially or fully sterilizing dose in small and large laboratory cages.

PubMed

Helinski, M E H; Knols, B G J

2008-07-01

Male mating competitiveness is a crucial parameter in many genetic control programs including the sterile insect technique (SIT). We evaluated competitiveness of male Anopheles arabiensis Patton as a function of three experimental variables: (1) small or large cages for mating, (2) the effects of either a partially sterilizing (70 Gy) or fully sterilizing (120 Gy) dose, and (3) pupal or adult irradiation. Irradiated males competed for females with an equal number of unirradiated males. Competitiveness was determined by measuring hatch rates of individually laid egg batches. In small cages, pupal irradiation with the high dose resulted in the lowest competitiveness, whereas adult irradiation with the low dose gave the highest, with the latter males being equal in competitiveness to unirradiated males. In the large cage, reduced competitiveness of males irradiated in the pupal stage was more pronounced compared with the small cage; the males irradiated as adults at both doses performed similarly to unirradiated males. Unexpectedly, males irradiated with the high dose performed better in a large cage than in a small one. A high proportion of intermediate hatch rates was observed for eggs collected in the large cage experiments with males irradiated at the pupal stage. It is concluded that irradiation of adult An. arabiensis with the partially sterilizing dose results in the highest competitiveness for both cage designs. Cage size affected competitiveness for some treatments; therefore, competitiveness determined in laboratory experiments must be confirmed by releases into simulated field conditions. The protocols described are readily transferable to evaluate male competitiveness for other genetic control techniques.

Spherical nanoindentation of proton irradiated 304 stainless steel: A comparison of small scale mechanical test techniques for measuring irradiation hardening

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weaver, Jordan S.; Pathak, Siddhartha; Reichardt, Ashley

Experimentally quantifying the mechanical effects of radiation damage in reactor materials is necessary for the development and qualification of new materials for improved performance and safety. This can be achieved in a high-throughput fashion through a combination of ion beam irradiation and small scale mechanical testing in contrast to the high cost and laborious nature of bulk testing of reactor irradiated samples. The current paper focuses on using spherical nanoindentation stress-strain curves on unirradiated and proton irradiated (10 dpa at 360 °C) 304 stainless steel to quantify the mechanical effects of radiation damage. Spherical nanoindentation stress-strain measurements show a radiation-inducedmore » increase in indentation yield strength from 1.36 GPa to 2.72 GPa and a radiation-induced increase in indentation work hardening rate of 10 GPa–30 GPa. These measurements are critically compared against Berkovich nanohardness, micropillar compression, and micro-tension measurements on the same material and similar grain orientations. The ratio of irradiated to unirradiated yield strength increases by a similar factor of 2 when measured via spherical nanoindentation or Berkovich nanohardness testing. A comparison of spherical indentation stress-strain curves to uniaxial (micropillar and micro-tension) stress-strain curves was achieved using a simple scaling relationship which shows good agreement for the unirradiated condition and poor agreement in post-yield behavior for the irradiated condition. Finally, the disagreement between spherical nanoindentation and uniaxial stress-strain curves is likely due to the plastic instability that occurs during uniaxial tests but is absent during spherical nanoindentation tests.« less

49 CFR 238.423 - Fuel tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

....423 Fuel tanks. (a) External fuel tanks. Each type of external fuel tank must be approved by FRA's... equivalent to a fuel tank that complies with the external fuel tank requirements in § 238.223(a). (b) Internal fuel tanks. Internal fuel tanks shall comply with the requirements specified in § 238.223(b). ...

Alternative Fuels Data Center: E85 Flex Fuel Specification

Science.gov Websites

Flexible-Fuel Automotive Spark-Ignition Engines. Fuel retailers or fleets purchasing E85 should require , there is no concern with carrying over winter fuel into the summer months because flexible-fuel vehicles requirements. D5798-15 Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark

40 CFR 80.510 - What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel? 80.510 Section 80.510 Protection of Environment... Information § 80.510 What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel...

40 CFR 80.510 - What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel? 80.510 Section 80.510 Protection of Environment... Information § 80.510 What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel...

Effect of Radiation Exposure on the Retention of Commercial NAND Flash Memory

NASA Technical Reports Server (NTRS)

Oldham, Timothy R.; Chen, D.; Friendlich, M.; Carts, M. A.; Seidleck, C. M.; LaBel, K. A.

2011-01-01

We have compared the data retention of irradiated commercial NAND flash memories with that of unirradiated controls. Under some circumstanc es, radiation exposure has a significant effect on the retention of f lash memories.

16 CFR 309.12 - Recordkeeping.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Manufacturers of Electric Vehicle Fuel Dispensing Systems § 309.12 Recordkeeping. You must keep for one year... Vehicle Fuels (Other Than Electricity) and of Electric Vehicle Fuel Dispensing Systems ... REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of...

16 CFR 309.12 - Recordkeeping.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Manufacturers of Electric Vehicle Fuel Dispensing Systems § 309.12 Recordkeeping. You must keep for one year... Vehicle Fuels (Other Than Electricity) and of Electric Vehicle Fuel Dispensing Systems ... REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of...

16 CFR 309.12 - Recordkeeping.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Manufacturers of Electric Vehicle Fuel Dispensing Systems § 309.12 Recordkeeping. You must keep for one year... Vehicle Fuels (Other Than Electricity) and of Electric Vehicle Fuel Dispensing Systems ... REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of...

16 CFR 309.12 - Recordkeeping.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Manufacturers of Electric Vehicle Fuel Dispensing Systems § 309.12 Recordkeeping. You must keep for one year... Vehicle Fuels (Other Than Electricity) and of Electric Vehicle Fuel Dispensing Systems ... REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of...

40 CFR 80.603 - What are the pre-compliance reporting requirements for NRLM diesel fuel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for NRLM diesel fuel? 80.603 Section 80.603 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Recordkeeping and Reporting...

40 CFR 80.603 - What are the pre-compliance reporting requirements for NRLM diesel fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for NRLM diesel fuel? 80.603 Section 80.603 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Recordkeeping and Reporting...

78 FR 16498 - Proposed Information Collection Request; Comment Request; Registration of Fuels and Fuel...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-15

... fuel or additive, and certain technical, marketing, and health-effects information. The development of... Request; Comment Request; Registration of Fuels and Fuel Additives--Requirements for Manufacturers; EPA... Fuels and Fuel Additives--Requirements for Manufacturers'' (EPA ICR No. 0309.14, OMB Control No. 2060...

Alternative Fuels Data Center: Status Update: Requirements Have Not Changed

Science.gov Websites

Fuels Data Center: Status Update: Requirements Have Not Changed (June 2008) on Facebook Tweet about Alternative Fuels Data Center: Status Update: Requirements Have Not Changed (June 2008) on Twitter Bookmark Alternative Fuels Data Center: Status Update: Requirements Have Not Changed (June 2008) on Google Bookmark

40 CFR 80.583 - What alternative sampling and testing requirements apply to importers who transport motor vehicle...

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements apply to importers who transport motor vehicle diesel fuel, NRLM diesel fuel, or ECA marine fuel... (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Sampling and Testing § 80.583 What...

16 CFR 309.10 - Alternative vehicle fuel rating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Alternative vehicle fuel rating. 309.10... LABELING REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of Importers, Producers, and Refiners of Non-Liquid Alternative Vehicle Fuels (other Than...

Alternate-Fueled Combustor-Sector Performance: Part A: Combustor Performance Part B: Combustor Emissions

NASA Technical Reports Server (NTRS)

Shouse, D. T.; Neuroth, C.; Henricks, R. C.; Lynch, A.; Frayne, C.; Stutrud, J. S.; Corporan, E.; Hankins, T.

2010-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F(2008) or ASTM D 7566 (2010) standards, respectively, and are classified as drop-in fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are certified individually on the basis of feedstock. Adherence to alternate fuels and fuel blends requires smart fueling systems or advanced fuel-flexible systems, including combustors and engines without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance (Part A) and emissions and particulates (Part B) combustor sector data for synthetic-parafinic-kerosene- (SPK-) type fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling.

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 25.991 Section 25.991...

40 CFR 79.5 - Periodic reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) REGISTRATION OF FUELS AND FUEL ADDITIVES General Provisions § 79.5 Periodic reporting requirements. (a) Fuel..., October through December) commencing after the date prescribed for a particular fuel in subpart D, fuel manufacturers shall submit to the Administrator a report for each registered fuel showing (i) the range of...

40 CFR 79.5 - Periodic reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) REGISTRATION OF FUELS AND FUEL ADDITIVES General Provisions § 79.5 Periodic reporting requirements. (a) Fuel..., October through December) commencing after the date prescribed for a particular fuel in subpart D, fuel manufacturers shall submit to the Administrator a report for each registered fuel showing (i) the range of...

40 CFR 1065.701 - General requirements for test fuels.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false General requirements for test fuels... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration Standards § 1065.701 General requirements for test fuels. (a) General. For all emission...

40 CFR 1065.701 - General requirements for test fuels.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false General requirements for test fuels... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration Standards § 1065.701 General requirements for test fuels. (a) General. For all emission...

40 CFR 1065.701 - General requirements for test fuels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false General requirements for test fuels... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration Standards § 1065.701 General requirements for test fuels. (a) General. For all emission...

40 CFR 1065.701 - General requirements for test fuels.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false General requirements for test fuels... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration Standards § 1065.701 General requirements for test fuels. (a) General. For all emission...

Hydrogen for the subsonic transport. [aircraft design and fuel requirements

NASA Technical Reports Server (NTRS)

Korycinski, P. F.; Snow, D. B.

1975-01-01

Relations between air travel and fuel requirements are examined. Alternate fuels considered in connection with problems related to a diminishing supply of petroleum include synthetic jet fuel, methane, and hydrogen. A cruise flight of a subsonic aircraft on a hydrogen-fueled jet engine was demonstrated in 1957. However, more development work is required to provide a sound engineering base for a complete air transportation system using hydrogen as fuel. Aircraft designs for alternate fuels are discussed, giving attention to hydrogen-related technology already available and new developments which are needed.

30 CFR 56.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fuel oil requirements for ANFO. 56.6309 Section 56.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... § 56.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels with flash points lower than...

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fuel oil requirements for ANFO. 57.6309 Section 57.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels...

30 CFR 56.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuel oil requirements for ANFO. 56.6309 Section 56.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... § 56.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels with flash points lower than...

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuel oil requirements for ANFO. 57.6309 Section 57.6309 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels...

30 CFR 75.1901 - Diesel fuel requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Diesel fuel requirements. 75.1901 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1901 Diesel fuel requirements. (a) Diesel-powered equipment shall be used underground only with a diesel fuel having a sulfur...

30 CFR 75.1901 - Diesel fuel requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Diesel fuel requirements. 75.1901 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1901 Diesel fuel requirements. (a) Diesel-powered equipment shall be used underground only with a diesel fuel having a sulfur...

40 CFR 86.000-9 - Emission standards for 2000 and later model year light-duty trucks.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86... leanest air to fuel mixture required to obtain maximum torque (lean best torque), plus a tolerance of six... fuel ratio shall not be richer at any time than the leanest air to fuel mixture required to obtain...

40 CFR 86.000-9 - Emission standards for 2000 and later model year light-duty trucks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86... leanest air to fuel mixture required to obtain maximum torque (lean best torque), plus a tolerance of six... fuel ratio shall not be richer at any time than the leanest air to fuel mixture required to obtain...

76 FR 8661 - Airworthiness Directives; Lycoming Engines, Fuel Injected Reciprocating Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

... engine models requiring inspections. We are proposing this AD to prevent failure of the fuel injector... repetitive inspection compliance time. We issued that AD to prevent failure of the fuel injector fuel lines... engine models requiring inspection. We are issuing this AD to prevent failure of the fuel injector fuel...

40 CFR 86.1206-96 - Equipment required; overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.1206-96 Equipment required; overview. This subpart... methanol-fueled heavy-duty vehicles. Equipment required and specifications are as follows: (a) Evaporative...

40 CFR 86.1206-96 - Equipment required; overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.1206-96 Equipment required; overview. This subpart... methanol-fueled heavy-duty vehicles. Equipment required and specifications are as follows: (a) Evaporative...

Enzyme-activatable imaging probe reveals enhanced neutrophil elastase activity in tumors following photodynamic therapy

PubMed Central

Modi, Kshitij D.; Foster, Thomas H.

2013-01-01

Abstract. We demonstrate the use of an enzyme-activatable fluorogenic probe, Neutrophil Elastase 680 FAST (NE680), for in vivo imaging of neutrophil elastase (NE) activity in tumors subjected to photodynamic therapy (PDT). NE protease activity was assayed in SCC VII and EMT6 tumors established in C3H and BALB/c mice, respectively. Four nanomoles of NE680 was injected intravenously immediately following PDT irradiation. 5 h following administration of NE680, whole-mouse fluorescence imaging was performed. At this time point, levels of NE680 fluorescence were at least threefold greater in irradiated versus unirradiated SCC VII and EMT6 tumors sensitized with Photofrin. To compare possible photosensitizer-specific differences in therapy-induced elastase activity, EMT6 tumors were also subjected to 2-(1-hexyloxyethyl)-2-devinyl pyropheophorbide-a (HPPH)-PDT. NE levels measured in HPPH-PDT-treated tumors were twofold higher than in unirradiated controls. Ex vivo labeling of host cells using fluorophore-conjugated antibodies and confocal imaging were used to visualize Gr1+ cells in Photofrin-PDT-treated EMT6 tumors. These data were compared with recently reported analysis of Gr1+ cell accumulation in EMT6 tumors subjected to HPPH-PDT. The population density of infiltrating Gr1+ cells in treated versus unirradiated drug-only control tumors suggests that the differential in NE680 fold enhancement observed in Photofrin versus HPPH treatment may be attributed to the significantly increased inflammatory response induced by Photofrin-PDT. The in vivo imaging of NE680, which is a fluorescent reporter of NE extracellular release caused by neutrophil activation, demonstrates that PDT results in increased NE levels in treated tumors, and the accumulation of the cleaved probe tracks qualitatively with the intratumor Gr1+ cell population. PMID:23897439

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel pumps. 23.991 Section 23.991...

10 CFR 73.37 - Requirements for physical protection of irradiated reactor fuel in transit.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Requirements for physical protection of irradiated reactor... Requirements for physical protection of irradiated reactor fuel in transit. (a) Performance objectives. (1... of irradiated reactor fuel in excess of 100 grams in net weight of irradiated fuel, exclusive of...

10 CFR 73.37 - Requirements for physical protection of irradiated reactor fuel in transit.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Requirements for physical protection of irradiated reactor... Requirements for physical protection of irradiated reactor fuel in transit. (a) Performance objectives. (1... of irradiated reactor fuel in excess of 100 grams in net weight of irradiated fuel, exclusive of...

40 CFR 80.604 - What are the annual reporting requirements for refiners and importers of NRLM diesel fuel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for refiners and importers of NRLM diesel fuel? 80.604 Section 80.604 Protection of Environment... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel... importers of NRLM diesel fuel? Beginning with the annual compliance period that begins June 1, 2007, or the...

40 CFR 80.604 - What are the annual reporting requirements for refiners and importers of NRLM diesel fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for refiners and importers of NRLM diesel fuel? 80.604 Section 80.604 Protection of Environment... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel... importers of NRLM diesel fuel? Beginning with the annual compliance period that begins June 1, 2007, or the...

Identification of gamma-irradiated foodstuffs by chemiluminescence measurements in Taiwan

NASA Astrophysics Data System (ADS)

Ma, Ming-Shia Chang; Chen, Li-Hsiang; Tsai, Zei-Tsan; Fu, Ying-Kai

In order to establish chemiluminescence (CL) measurements as an identification method for γ-irradiated foodstuffs in Taiwan, ten agricultural products including wheat flour, rice, ginger, potatoes, garlic, onions, red beans, mung beans, soy beans, xanthoxylon seeds and Japanese star anises have been tested to compare CL intensities between untreated samples and samples subject to a 10 kGy γ-irradiation dose. Amongst them, wheat flour is the most eligible product to be identified by CL measurements. The CL intensities of un-irradiated and irradiated flour have shown large differences associated with a significant dose-effect relationship. Effects of three different protein contents of flour, unsieved and sieved (100-200 mesh), the reproducibility and the storage experiment on CL intensities at various doses were investigated in this study. In addition, the white bulb part of onions has shown some CL in irradiated samples. The CL data obtained from the other eight agricultural products have shown large fluctuations and cannot be used to differentiate between irradiated and un-irradiated samples.

Some cell kinetic effects of combined injury with ionizing radiation and cyclophosphamide on mouse bladder urothelium.

PubMed

Reitan, J B

1985-01-01

Cyclophosphamide was given intraperitoneally to groups of eight female mice 48 h after local electron irradiation to the bladder with 0, 10 and 20 Gy respectively. The reactions in the urothelium were monitored by histology, incorporation of tritiated thymidine and flow cytometry. A wave of increased thymidine incorporation combined with an increase in the proportion of diploid S-phase cells was seen in the unirradiated bladders 24 h after the drug treatment, followed by normalization after 1 week. This response was significantly less pronounced in the irradiated animals. In the unirradiated animals a similar wave characterized by an increased proportion of octaploid cells was also seen, but this wave occurred later in the irradiated animals. Severe injury was observed in the rectum of the 20 Gy-irradiated animals. Irradiation prior to drug treatment led to only small effects, but a decreased ability for regenerative DNA synthesis after drug injury seems to persist. This affects both proliferation and the building up of polyploidy.

[Identification of irradiated abalone by ESR spectroscopy].

PubMed

Song, Yeping; Wang, Chuanxian; Yang, Zhenyu; Zhong, Weike; Geng, Jinpei; Lu, Di; Ding, Zhuoping

2012-05-01

To establish an analytical method for the detection and identification of irradiated abalone by electron spin resonance spectroscopy. Electron spin resonance (ESR) was used to study the spectral characteristics of abalone and the characteristic peak for quantitation. There were obvious different ESR spectra between unirradiated and irradiated abalone. The g factor for unirradiated abalone was 2.0055-2.0060, the g1 and g2 factor for irradiated abalone were (2.0027 +/- 0.0001) and (1.9994 +/- 0.0001), respectively. The ESR signal intensity of characteristic peak was positively correlated with absorbed dose in the range of 0.5 - 10 kGy, left peak was the characteristic peak for quantitation and the detection limit was < or = 0.5 kGy. It was difficult to quantitate when the absorbed dose was over 10 kGy. ESR characteristic peak and g factor were able to qualitatively determine the irradiation of abalone. ESR spectroscopy is an effective method to determine whether the abalone being irradiated or not.

RBS/Channeling Studies of Swift Heavy Ion Irradiated GaN Layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sathish, N.; Dhamodaran, S.; Pathak, A. P.

2009-03-10

Epitaxial GaN layers grown by MOCVD on c-plane sapphire substrates were irradiated with 150 MeV Ag ions at a fluence of 5x10{sup 12} ions/cm{sup 2}. Samples used in this study are 2 {mu}m thick GaN layers, with and without a thin AlN cap-layer. Energy dependent RBS/Channeling measurements have been carried out on both irradiated and unirradiated samples for defects characterization. Observed results are compared and correlated with previous HRXRD, AFM and optical studies. The {chi}{sub min} values for unirradiated samples show very high value and the calculated defect densities are of the order of 10{sup 10} cm{sup -2} as expectedmore » in these samples. Effects of irradiation on these samples are different as initial samples had different defect densities. Epitaxial reconstruction of GaN buffer layer has been attributed to the observed changes, which are generally grown to reduce the strain between GaN and Sapphire.« less

16 CFR 309.21 - Labeling requirements for used covered vehicles.

Code of Federal Regulations, 2011 CFR

2011-01-01

... ACTS OF CONGRESS LABELING REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fueled Vehicles § 309.21 Labeling requirements for used covered vehicles. (a... ink on Hammermill Offset Opaque Vellum/S.70 Sky Blue (or equivalent) paper. (e) Contents. Headlines...

16 CFR 309.20 - Labeling requirements for new covered vehicles.

Code of Federal Regulations, 2011 CFR

2011-01-01

... ACTS OF CONGRESS LABELING REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fueled Vehicles § 309.20 Labeling requirements for new covered vehicles. (a... printed in process black ink on Hammermill Offset Opaque Vellum/S.70 Sky Blue (or equivalent) paper. (e...

30 CFR 57.6309 - Fuel oil requirements for ANFO.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fuel oil requirements for ANFO. 57.6309 Section... Transportation-Surface and Underground § 57.6309 Fuel oil requirements for ANFO. (a) Liquid hydrocarbon fuels with flash points lower than that of No. 2 diesel oil (125 °F) shall not be used to prepare ammonium...

40 CFR 80.165 - Certification test procedures and standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Detergent Gasoline § 80.165 Certification test... detergent additive is mixed in a test fuel meeting all relevant requirements of § 80.164, including the... for such records. (a) Fuel injector deposit control testing. (1) The required test fuel must produce...

40 CFR 80.165 - Certification test procedures and standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Detergent Gasoline § 80.165 Certification test... detergent additive is mixed in a test fuel meeting all relevant requirements of § 80.164, including the... for such records. (a) Fuel injector deposit control testing. (1) The required test fuel must produce...

33 CFR 149.655 - What are the requirements for helicopter fueling facilities?

Code of Federal Regulations, 2014 CFR

2014-07-01

... helicopter fueling facilities? 149.655 Section 149.655 Navigation and Navigable Waters COAST GUARD... EQUIPMENT Design and Equipment Helicopter Fueling Facilities § 149.655 What are the requirements for helicopter fueling facilities? Helicopter fueling facilities must comply with 46 CFR 108.489 or an equivalent...

33 CFR 149.655 - What are the requirements for helicopter fueling facilities?

Code of Federal Regulations, 2013 CFR

2013-07-01

... helicopter fueling facilities? 149.655 Section 149.655 Navigation and Navigable Waters COAST GUARD... EQUIPMENT Design and Equipment Helicopter Fueling Facilities § 149.655 What are the requirements for helicopter fueling facilities? Helicopter fueling facilities must comply with 46 CFR 108.489 or an equivalent...

33 CFR 149.655 - What are the requirements for helicopter fueling facilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... helicopter fueling facilities? 149.655 Section 149.655 Navigation and Navigable Waters COAST GUARD... EQUIPMENT Design and Equipment Helicopter Fueling Facilities § 149.655 What are the requirements for helicopter fueling facilities? Helicopter fueling facilities must comply with 46 CFR 108.489 or an equivalent...

33 CFR 149.655 - What are the requirements for helicopter fueling facilities?

Code of Federal Regulations, 2012 CFR

2012-07-01

... helicopter fueling facilities? 149.655 Section 149.655 Navigation and Navigable Waters COAST GUARD... EQUIPMENT Design and Equipment Helicopter Fueling Facilities § 149.655 What are the requirements for helicopter fueling facilities? Helicopter fueling facilities must comply with 46 CFR 108.489 or an equivalent...

33 CFR 149.655 - What are the requirements for helicopter fueling facilities?

Code of Federal Regulations, 2011 CFR

2011-07-01

... helicopter fueling facilities? 149.655 Section 149.655 Navigation and Navigable Waters COAST GUARD... EQUIPMENT Design and Equipment Helicopter Fueling Facilities § 149.655 What are the requirements for helicopter fueling facilities? Helicopter fueling facilities must comply with 46 CFR 108.489 or an equivalent...

26 CFR 48.4082-2 - Diesel fuel and kerosene; notice required for dyed fuel.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Diesel fuel and kerosene; notice required for..., Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-2 Diesel fuel and kerosene; notice... “DYED KEROSENE, NONTAXABLE USE ONLY, PENALTY FOR TAXABLE USE” must be posted by a seller on any retail...

26 CFR 48.4082-2 - Diesel fuel and kerosene; notice required for dyed fuel.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 16 2013-04-01 2013-04-01 false Diesel fuel and kerosene; notice required for..., Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-2 Diesel fuel and kerosene; notice... “DYED KEROSENE, NONTAXABLE USE ONLY, PENALTY FOR TAXABLE USE” must be posted by a seller on any retail...

26 CFR 48.4082-2 - Diesel fuel and kerosene; notice required for dyed fuel.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 16 2011-04-01 2011-04-01 false Diesel fuel and kerosene; notice required for..., Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-2 Diesel fuel and kerosene; notice... “DYED KEROSENE, NONTAXABLE USE ONLY, PENALTY FOR TAXABLE USE” must be posted by a seller on any retail...

26 CFR 48.4082-2 - Diesel fuel and kerosene; notice required for dyed fuel.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 16 2012-04-01 2012-04-01 false Diesel fuel and kerosene; notice required for..., Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-2 Diesel fuel and kerosene; notice... “DYED KEROSENE, NONTAXABLE USE ONLY, PENALTY FOR TAXABLE USE” must be posted by a seller on any retail...

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Code of Federal Regulations, 2013 CFR

2013-10-01

... uranium or thorium. 173.426 Section 173.426 Transportation Other Regulations Relating to Transportation....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in which the sole Class 7 (radioactive) material content is natural uranium, unirradiated depleted uranium...

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Code of Federal Regulations, 2014 CFR

2014-10-01

... uranium or thorium. 173.426 Section 173.426 Transportation Other Regulations Relating to Transportation....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in which the sole Class 7 (radioactive) material content is natural uranium, unirradiated depleted uranium...

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Code of Federal Regulations, 2012 CFR

2012-10-01

... uranium or thorium. 173.426 Section 173.426 Transportation Other Regulations Relating to Transportation....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in which the sole Class 7 (radioactive) material content is natural uranium, unirradiated depleted uranium...

49 CFR 229.217 - Fuel tank.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Crashworthiness Design Requirements § 229.217 Fuel..., comply with the requirements of AAR S-5506, “Performance Requirements for Diesel Electric Locomotive Fuel...

46 CFR 78.17-75 - Requirements for fuel oil.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Requirements for fuel oil. 78.17-75 Section 78.17-75..., Drills, and Inspections § 78.17-75 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log be made of each supply of fuel oil received on board, stating the...

46 CFR 97.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Requirements for fuel oil. 97.15-55 Section 97.15-55... OPERATIONS Tests, Drills, and Inspections § 97.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on...

46 CFR 196.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Requirements for fuel oil. 196.15-55 Section 196.15-55... Test, Drills, and Inspections § 196.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on board...

46 CFR 97.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Requirements for fuel oil. 97.15-55 Section 97.15-55... OPERATIONS Tests, Drills, and Inspections § 97.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on...

46 CFR 196.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Test, Drills, and Inspections § 196.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on board... 46 Shipping 7 2014-10-01 2014-10-01 false Requirements for fuel oil. 196.15-55 Section 196.15-55...

46 CFR 97.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Requirements for fuel oil. 97.15-55 Section 97.15-55... OPERATIONS Tests, Drills, and Inspections § 97.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on...

46 CFR 196.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Requirements for fuel oil. 196.15-55 Section 196.15-55... Test, Drills, and Inspections § 196.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on board...

46 CFR 78.17-75 - Requirements for fuel oil.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 3 2012-10-01 2012-10-01 false Requirements for fuel oil. 78.17-75 Section 78.17-75..., Drills, and Inspections § 78.17-75 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log be made of each supply of fuel oil received on board, stating the...

46 CFR 196.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Requirements for fuel oil. 196.15-55 Section 196.15-55... Test, Drills, and Inspections § 196.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on board...

46 CFR 97.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Requirements for fuel oil. 97.15-55 Section 97.15-55... OPERATIONS Tests, Drills, and Inspections § 97.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on...

46 CFR 78.17-75 - Requirements for fuel oil.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 3 2013-10-01 2013-10-01 false Requirements for fuel oil. 78.17-75 Section 78.17-75..., Drills, and Inspections § 78.17-75 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log be made of each supply of fuel oil received on board, stating the...

46 CFR 78.17-75 - Requirements for fuel oil.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 3 2014-10-01 2014-10-01 false Requirements for fuel oil. 78.17-75 Section 78.17-75..., Drills, and Inspections § 78.17-75 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log be made of each supply of fuel oil received on board, stating the...

46 CFR 97.15-55 - Requirements for fuel oil.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Requirements for fuel oil. 97.15-55 Section 97.15-55... OPERATIONS Tests, Drills, and Inspections § 97.15-55 Requirements for fuel oil. (a) It shall be the duty of the chief engineer to cause an entry in the log to be made of each supply of fuel oil received on...

Radiation and Thermal Cycling Effects on EPC1001 Gallium Nitride Power Transistors

NASA Technical Reports Server (NTRS)

Patterson, Richard L.; Scheick, Leif Z.; Lauenstein, Jean M.; Casey, Megan C.; Hammoud, Ahmad

2012-01-01

Electronics designed for use in NASA space missions are required to work efficiently and reliably under harsh environment conditions. These include radiation, extreme temperatures, and thermal cycling, to name a few. Information pertaining to performance of electronic parts and systems under hostile environments is very scarce, especially for new devices. Such data is very critical so that proper design is implemented in order to ensure mission success and to mitigate risks associated with exposure of on-board systems to the operational environment. In this work, newly-developed enhancement-mode field effect transistors (FET) based on gallium nitride (GaN) technology were exposed to various particles of ionizing radiation and to long-term thermal cycling over a wide temperature range. Data obtained on control (un-irradiated) and irradiated samples of these power transistors are presented and the results are discussed.

Hematopoietic progenitor migration to the adult thymus

PubMed Central

Zlotoff, Daniel A.; Bhandoola, Avinash

2010-01-01

While most hematopoietic lineages develop in the bone marrow (BM), T cells uniquely complete their development in the specialized environment of the thymus. Hematopoietic stem cells with long-term self-renewal capacity are not present in the thymus. As a result, continuous T cell development requires that BM-derived progenitors be imported into the thymus throughout adult life. The process of thymic homing begins with the mobilization of progenitors out of the bone marrow, continues with their circulation in the bloodstream, and concludes with their settling in the thymus. This review will discuss each of these steps as they occur in the unirradiated and post-irradiation scenarios, focusing on the molecular mechanisms of regulation. Improved knowledge about these early steps in T cell generation may accelerate the development of new therapeutic options in patients with impaired T cell number or function. PMID:21251013

75 FR 34661 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-81 (MD-81), DC-9-82 (MD-82...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-18

... auxiliary fuel tanks, depending on the airplane configuration. This proposed AD results from fuel system... Fuel Tank System Design Review, Flammability Reduction and Maintenance and Inspection Requirements... substantiate that their fuel tank systems can prevent ignition sources in the fuel tanks. This requirement...

40 CFR 98.36 - Data reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fossil fuels only, the annual CO2 emissions for all fuels combined. Reporting CO2 emissions by type of fuel is not required. (ii) For units that burn both fossil fuels and biomass, the annual CO2 emissions from combustion of all fossil fuels combined and the annual CO2 emissions from combustion of all...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

40 CFR 600.303-12 - Fuel economy label-special requirements for flexible-fuel vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Fuel economy label-special requirements for flexible-fuel vehicles. 600.303-12 Section 600.303-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR...

40 CFR 600.303-12 - Fuel economy label-special requirements for flexible-fuel vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Fuel economy label-special requirements for flexible-fuel vehicles. 600.303-12 Section 600.303-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR...

40 CFR 600.303-12 - Fuel economy label-special requirements for flexible-fuel vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Fuel economy label-special requirements for flexible-fuel vehicles. 600.303-12 Section 600.303-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR...

Certification of alternative aviation fuels and blend components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson III, George R.; Edwards, Tim; Corporan, Edwin

2013-01-15

Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meetingmore » the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.« less

Gas detection for alternate-fuel vehicle facilities.

PubMed

Ferree, Steve

2003-05-01

Alternative fuel vehicles' safety is driven by local, state, and federal regulations in which fleet owners in key metropolitan [table: see text] areas convert much of their fleet to cleaner-burning fuels. Various alternative fuels are available to meet this requirement, each with its own advantages and requirements. This conversion to alternative fuels leads to special requirements for safety monitoring in the maintenance facilities and refueling stations. A comprehensive gas and flame monitoring system needs to meet the needs of both the user and the local fire marshal.

Fuel cells for low power applications

NASA Astrophysics Data System (ADS)

Heinzel, A.; Hebling, C.; Müller, M.; Zedda, M.; Müller, C.

Electronic devices show an ever-increasing power demand and thus, require innovative concepts for power supply. For a wide range of power and energy capacity, membrane fuel cells are an attractive alternative to conventional batteries. The main advantages are the flexibility with respect to power and capacity achievable with different devices for energy conversion and energy storage, the long lifetime and long service life, the good ecological balance, very low self-discharge. Therefore, the development of fuel cell systems for portable electronic devices is an attractive, although also a challenging, goal. The fuel for a membrane fuel cell might be hydrogen from a hydride storage system or methanol/water as a liquid alternative. The main differences between the two systems are the much higher power density for hydrogen fuel cells, the higher energy density per weight for the liquid fuel, safety aspects and infrastructure for fuel supply for hydride materials. For different applications, different system designs are required. High power cells are required for portable computers, low power methanol fuel cells required for mobile phones in hybrid systems with batteries and micro-fuel cells are required, e.g. for hand held PCs in the sub-Watt range. All these technologies are currently under development. Performance data and results of simulations and experimental investigations will be presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawlowski, Alexander; Splitter, Derek A

It is well known that spark ignited engine performance and efficiency is closely coupled to fuel octane number. The present work combines historical and recent trends in spark ignition engines to build a database of engine design, performance, and fuel octane requirements over the past 80 years. The database consists of engine compression ratio, required fuel octane number, peak mean effective pressure, specific output, and combined unadjusted fuel economy for passenger vehicles and light trucks. Recent trends in engine performance, efficiency, and fuel octane number requirement were used to develop correlations of fuel octane number utilization, performance, specific output. Themore » results show that historically, engine compression ratio and specific output have been strongly coupled to fuel octane number. However, over the last 15 years the sales weighted averages of compression ratios, specific output, and fuel economy have increased, while the fuel octane number requirement has remained largely unchanged. Using the developed correlations, 10-year-out projections of engine performance, design, and fuel economy are estimated for various fuel octane numbers, both with and without turbocharging. The 10-year-out projection shows that only by keeping power neutral while using 105 RON fuel will allow the vehicle fleet to meet CAFE targets if only the engine is relied upon to decrease fuel consumption. If 98 RON fuel is used, a power neutral fleet will have to reduce vehicle weight by 5%.« less

10 CFR 490.306 - Vehicle operation requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Vehicle operation requirements. 490.306 Section 490.306 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Alternative Fuel Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled...

10 CFR 490.306 - Vehicle operation requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Vehicle operation requirements. 490.306 Section 490.306 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Alternative Fuel Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled...

10 CFR 490.306 - Vehicle operation requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Vehicle operation requirements. 490.306 Section 490.306 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Alternative Fuel Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled...

10 CFR 490.306 - Vehicle operation requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Vehicle operation requirements. 490.306 Section 490.306 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Alternative Fuel Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled...

10 CFR 490.306 - Vehicle operation requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Vehicle operation requirements. 490.306 Section 490.306 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Alternative Fuel Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled...

CORN AND TUNA DIET--REPORT OF OBSERVATIONS ON NUTRITION: RADIATION AND STERILIZATION OF FOODS FOR HAZELTON LABORATORIES, FALLS CHURCH, VIRGINIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, M.A.

1963-09-15

No evidence was found to suggest that the consumption of irradiated corn or tuna fish produced lesions in rats significantly different in incidence or type than was found in animals that consumed the unirradiated products. (C.H.)

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Excepted packages for articles containing natural....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in which the sole Class 7 (radioactive) material content is natural uranium, unirradiated depleted uranium...

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Excepted packages for articles containing natural....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in which the sole Class 7 (radioactive) material content is natural uranium, unirradiated depleted uranium...

40 CFR 80.1610 - Standards and requirements for producers and importers of denatured fuel ethanol and other...

Code of Federal Regulations, 2014 CFR

2014-07-01

... producers and importers of denatured fuel ethanol and other oxygenates designated for use in transportation... requirements for producers and importers of denatured fuel ethanol and other oxygenates designated for use in transportation fuel. Beginning January 1, 2017, producers and importers of denatured fuel ethanol (DFE) or other...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2014 CFR

2014-07-01

... exempted under § 80.607. (iii) For use in the U.S. Territories as provided under § 80.608. (iv) Jet fuel... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... exempted under § 80.607. (iii) For use in the U.S. Territories as provided under § 80.608. (iv) Jet fuel... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2012 CFR

2012-07-01

... exempted under § 80.607. (iii) For use in the U.S. Territories as provided under § 80.608. (iv) Jet fuel... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... exempted under § 80.607. (iii) For use in the U.S. Territories as provided under § 80.608. (iv) Jet fuel... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Code of Federal Regulations, 2013 CFR

2013-07-01

... exempted under § 80.607. (iii) For use in the U.S. Territories as provided under § 80.608. (iv) Jet fuel... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

27 CFR 19.718 - Required records.

Code of Federal Regulations, 2011 CFR

2011-04-01

....718 Required records. A proprietor of an alcohol fuel plant must maintain records that accurately... proprietor must maintain records of all production, receipts, and manufacture at the alcohol fuel plant. This... render the spirits unfit for beverage use; and (6) The quantity of fuel alcohol manufactured. Fuel...

76 FR 31467 - Guide Concerning Fuel Economy Advertising for New Automobiles

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

...The Federal Trade Commission (``FTC'' or ``Commission'') gives notice that it is postponing any amendments to its Guide Concerning Fuel Economy Advertising for New Automobiles (``Fuel Economy Guide'' or ``Guide'') pending completion of ongoing review by the Environmental Protection Agency (``EPA'') and the National Highway Traffic Safety Administration (``NHTSA'') of current fuel economy labeling requirements and the Commission's accelerated regulatory review of its own Labeling Requirements for Alternative Fuels and Alternative Fueled Vehicles Rule (``Alternative Fuels Rule'').

Accelerator-driven transmutation of spent fuel elements

DOEpatents

Venneri, Francesco; Williamson, Mark A.; Li, Ning

2002-01-01

An apparatus and method is described for transmuting higher actinides, plutonium and selected fission products in a liquid-fuel subcritical assembly. Uranium may also be enriched, thereby providing new fuel for use in conventional nuclear power plants. An accelerator provides the additional neutrons required to perform the processes. The size of the accelerator needed to complete fuel cycle closure depends on the neutron efficiency of the supported reactors and on the neutron spectrum of the actinide transmutation apparatus. Treatment of spent fuel from light water reactors (LWRs) using uranium-based fuel will require the largest accelerator power, whereas neutron-efficient high temperature gas reactors (HTGRs) or CANDU reactors will require the smallest accelerator power, especially if thorium is introduced into the newly generated fuel according to the teachings of the present invention. Fast spectrum actinide transmutation apparatus (based on liquid-metal fuel) will take full advantage of the accelerator-produced source neutrons and provide maximum utilization of the actinide-generated fission neutrons. However, near-thermal transmutation apparatus will require lower standing

40 CFR 88.305-94 - Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for heavy-duty vehicles. 88.305-94 Section 88.305-94 Protection of Environment ENVIRONMENTAL...-94 Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles. (a) All clean-fuel heavy... LEV, ULEV, or ZEV, and meets all of the applicable requirements of this part 88. (b) All heavy-duty...

40 CFR 80.591 - What are the product transfer document requirements for additives to be used in diesel fuel?

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for additives to be used in diesel fuel? 80.591 Section 80.591 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... additives to be used in diesel fuel? (a) Except as provided in paragraphs (b) and (d) of this section, on...

40 CFR 80.591 - What are the product transfer document requirements for additives to be used in diesel fuel?

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for additives to be used in diesel fuel? 80.591 Section 80.591 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... additives to be used in diesel fuel? (a) Except as provided in paragraphs (b) and (d) of this section, on...

40 CFR 80.591 - What are the product transfer document requirements for additives to be used in diesel fuel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for additives to be used in diesel fuel? 80.591 Section 80.591 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... additives to be used in diesel fuel? (a) Except as provided in paragraphs (b) and (d) of this section, on...

40 CFR 80.591 - What are the product transfer document requirements for additives to be used in diesel fuel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for additives to be used in diesel fuel? 80.591 Section 80.591 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... additives to be used in diesel fuel? (a) Except as provided in paragraphs (b) and (d) of this section, on...

40 CFR 80.591 - What are the product transfer document requirements for additives to be used in diesel fuel?

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for additives to be used in diesel fuel? 80.591 Section 80.591 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES... additives to be used in diesel fuel? (a) Except as provided in paragraphs (b) and (d) of this section, on...

40 CFR 88.305-94 - Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles. 88.305-94 Section 88.305-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CLEAN-FUEL VEHICLES Clean-Fuel Fleet Program § 88.305-94 Clean-fuel fleet vehicle labeling...

40 CFR 88.305-94 - Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles. 88.305-94 Section 88.305-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CLEAN-FUEL VEHICLES Clean-Fuel Fleet Program § 88.305-94 Clean-fuel fleet vehicle labeling...

40 CFR 88.305-94 - Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles. 88.305-94 Section 88.305-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CLEAN-FUEL VEHICLES Clean-Fuel Fleet Program § 88.305-94 Clean-fuel fleet vehicle labeling...

40 CFR 88.305-94 - Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Clean-fuel fleet vehicle labeling requirements for heavy-duty vehicles. 88.305-94 Section 88.305-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CLEAN-FUEL VEHICLES Clean-Fuel Fleet Program § 88.305-94 Clean-fuel fleet vehicle labeling...

Alternative fuels for multiple-hearth furnaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bracken, B.D.; Lawson, T.U.

1980-04-01

A study of alternative procedures for reducing the consumption of No. 2 fuel oil at the Lower Molonglo Water Quality Control Centre near Canberra, Aust., indicated that in comparison with the present system of incineration with heat supplied by burning fuel oil, the installation of a sludge drying operation, consisting of a rotary dryer heated by furnace exhaust gases with the dried sludge used to fuel the furnace, would become economically desirable by 1985 if afterburning is not required, and would be justified immediately if afterburning is required to meet air pollution control regulations. The substitution of any of fourmore » waste fuels (refuse-derived fuel, waste paper, wood waste, or waste oil) or of coal for the No. 2 fuel oil would not be cost-effective through 1989. The furnace system, including afterburning and fuel oil requirements, the envisioned alternative fuel use systems, sludge processing alternatives, heat balance results, and economics are discussed.« less

14 CFR 121.281 - Fuel system independence.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Fuel system independence. 121.281 Section... REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Special Airworthiness Requirements § 121.281 Fuel system independence. (a) Each airplane fuel system must be arranged so that the failure of any one...

40 CFR 80.1141 - Small refinery exemption.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Renewable Fuel Standard § 80.1141 Small refinery exemption...)), is exempt from the renewable fuel standards of § 80.1105 and the requirements that apply to obligated... refinery application. The application must contain all of the elements required for small refinery...

40 CFR 80.92 - Baseline auditor requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Baseline auditor requirements. 80.92... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Anti-Dumping § 80.92 Baseline auditor requirements. (a... determination methodology, resulting baseline fuel parameter, volume and emissions values verified by an auditor...

Transcriptional profiling suggests that multiple metabolic adaptations are required for effective proliferation of Pseudomonas aeruginosa in jet fuel.

PubMed

Gunasekera, Thusitha S; Striebich, Richard C; Mueller, Susan S; Strobel, Ellen M; Ruiz, Oscar N

2013-01-01

Fuel is a harsh environment for microbial growth. However, some bacteria can grow well due to their adaptive mechanisms. Our goal was to characterize the adaptations required for Pseudomonas aeruginosa proliferation in fuel. We have used DNA-microarrays and RT-PCR to characterize the transcriptional response of P. aeruginosa to fuel. Transcriptomics revealed that genes essential for medium- and long-chain n-alkane degradation including alkB1 and alkB2 were transcriptionally induced. Gas chromatography confirmed that P. aeruginosa possesses pathways to degrade different length n-alkanes, favoring the use of n-C11-18. Furthermore, a gamut of synergistic metabolic pathways, including porins, efflux pumps, biofilm formation, and iron transport, were transcriptionally regulated. Bioassays confirmed that efflux pumps and biofilm formation were required for growth in jet fuel. Furthermore, cell homeostasis appeared to be carefully maintained by the regulation of porins and efflux pumps. The Mex RND efflux pumps were required for fuel tolerance; blockage of these pumps precluded growth in fuel. This study provides a global understanding of the multiple metabolic adaptations required by bacteria for survival and proliferation in fuel-containing environments. This information can be applied to improve the fuel bioremediation properties of bacteria.

Recent developments in BWR fuel design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, S.P.; Noble, L.D.; Wood, J.E.

1991-11-01

Substantial increases in the cost effectiveness and performance capability of boiling water reactor (BWR) fuel designs have been implemented in the past 5 to 7 yr. This increase has been driven by (a) utility desires to lower fuel and operating costs and (b) design innovations that have lowered enrichment requirements, improved thermal-hydraulic performance, and increased discharge exposure. Higher discharge exposures reduce disposal costs for European and Asian utilities and enable US utilities to lengthen operating cycles. A typical BWR reload fuel bundle fabricated today has 25% higher {sup 235}U enrichment and a factor of 2 higher gadolinium loading than onemore » made several years ago. Today's BWR fuel bundles also contain more unheated water reduces the axial water density variation, lowers the void coefficient, and enhances the neutron efficiency of the bundle, reducing both the gadolinium poison and the enrichment requirements. In addition to these general trends, the following unique design innovations have further enhanced the fuel cost efficiency and performance characteristics of BWR fuel: ferrule spacer, part length rods, interactive channel, and bundle enhanced spectral shift. GE's fuel designs offer the flexibility for modern BWR fuel requirements and contain unique design features that enhance flexibility for modern BWR fuel requirements and contain unique design features that enhance flexibility and fuel cycle economics.« less

30 CFR 75.1902 - Underground diesel fuel storage-general requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Underground diesel fuel storage-general... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1902 Underground diesel fuel storage—general requirements. (a) All diesel fuel must be stored...

30 CFR 75.1902 - Underground diesel fuel storage-general requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Underground diesel fuel storage-general... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1902 Underground diesel fuel storage—general requirements. (a) All diesel fuel must be stored...

40 CFR 79.22 - Determination of noncompliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) REGISTRATION OF FUELS AND FUEL ADDITIVES Additive Registration Procedures § 79.22 Determination... fuel additive has failed to submit all of the information required by § 79.21, or determines within the... which is required prior to registration of the fuel additive by any provision of subpart F of this part...

40 CFR 79.22 - Determination of noncompliance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) REGISTRATION OF FUELS AND FUEL ADDITIVES Additive Registration Procedures § 79.22 Determination... fuel additive has failed to submit all of the information required by § 79.21, or determines within the... which is required prior to registration of the fuel additive by any provision of subpart F of this part...

40 CFR 79.22 - Determination of noncompliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) REGISTRATION OF FUELS AND FUEL ADDITIVES Additive Registration Procedures § 79.22 Determination... fuel additive has failed to submit all of the information required by § 79.21, or determines within the... which is required prior to registration of the fuel additive by any provision of subpart F of this part...

40 CFR 79.22 - Determination of noncompliance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) REGISTRATION OF FUELS AND FUEL ADDITIVES Additive Registration Procedures § 79.22 Determination... fuel additive has failed to submit all of the information required by § 79.21, or determines within the... which is required prior to registration of the fuel additive by any provision of subpart F of this part...

40 CFR 79.22 - Determination of noncompliance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) REGISTRATION OF FUELS AND FUEL ADDITIVES Additive Registration Procedures § 79.22 Determination... fuel additive has failed to submit all of the information required by § 79.21, or determines within the... which is required prior to registration of the fuel additive by any provision of subpart F of this part...

30 CFR 36.22 - Fuel-injection system.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fuel-injection system. 36.22 Section 36.22... EQUIPMENT Construction and Design Requirements § 36.22 Fuel-injection system. This system shall be so.... Provision shall be made for convenient adjustment of the maximum fuel-injection rate to that required for...

30 CFR 36.22 - Fuel-injection system.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fuel-injection system. 36.22 Section 36.22... EQUIPMENT Construction and Design Requirements § 36.22 Fuel-injection system. This system shall be so.... Provision shall be made for convenient adjustment of the maximum fuel-injection rate to that required for...

30 CFR 36.22 - Fuel-injection system.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Fuel-injection system. 36.22 Section 36.22... EQUIPMENT Construction and Design Requirements § 36.22 Fuel-injection system. This system shall be so.... Provision shall be made for convenient adjustment of the maximum fuel-injection rate to that required for...

30 CFR 36.22 - Fuel-injection system.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fuel-injection system. 36.22 Section 36.22... EQUIPMENT Construction and Design Requirements § 36.22 Fuel-injection system. This system shall be so.... Provision shall be made for convenient adjustment of the maximum fuel-injection rate to that required for...

30 CFR 36.22 - Fuel-injection system.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuel-injection system. 36.22 Section 36.22... EQUIPMENT Construction and Design Requirements § 36.22 Fuel-injection system. This system shall be so.... Provision shall be made for convenient adjustment of the maximum fuel-injection rate to that required for...

A comparison of hydrogen, methanol and gasoline as fuels for fuel cell vehicles: implications for vehicle design and infrastructure development

NASA Astrophysics Data System (ADS)

Ogden, Joan M.; Steinbugler, Margaret M.; Kreutz, Thomas G.

All fuel cells currently being developed for near term use in electric vehicles require hydrogen as a fuel. Hydrogen can be stored directly or produced onboard the vehicle by reforming methanol, or hydrocarbon fuels derived from crude oil (e.g., gasoline, diesel, or middle distillates). The vehicle design is simpler with direct hydrogen storage, but requires developing a more complex refueling infrastructure. In this paper, we present modeling results comparing three leading options for fuel storage onboard fuel cell vehicles: (a) compressed gas hydrogen storage, (b) onboard steam reforming of methanol, (c) onboard partial oxidation (POX) of hydrocarbon fuels derived from crude oil. We have developed a fuel cell vehicle model, including detailed models of onboard fuel processors. This allows us to compare the vehicle performance, fuel economy, weight, and cost for various vehicle parameters, fuel storage choices and driving cycles. The infrastructure requirements are also compared for gaseous hydrogen, methanol and gasoline, including the added costs of fuel production, storage, distribution and refueling stations. The delivered fuel cost, total lifecycle cost of transportation, and capital cost of infrastructure development are estimated for each alternative. Considering both vehicle and infrastructure issues, possible fuel strategies leading to the commercialization of fuel cell vehicles are discussed.

40 CFR Appendix P to Part 51 - Minimum Emission Monitoring Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... respective monitoring requirements are listed below. 1.1.1 Fossil fuel-fired steam generators, as specified... this appendix to meet the following basic requirements. 2.1 Fossil fuel-fired steam generators. Each fossil fuel-fired steam generator, except as provided in the following subparagraphs, with an annual...

40 CFR Appendix P to Part 51 - Minimum Emission Monitoring Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... respective monitoring requirements are listed below. 1.1.1 Fossil fuel-fired steam generators, as specified... this appendix to meet the following basic requirements. 2.1 Fossil fuel-fired steam generators. Each fossil fuel-fired steam generator, except as provided in the following subparagraphs, with an annual...

40 CFR Appendix P to Part 51 - Minimum Emission Monitoring Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... respective monitoring requirements are listed below. 1.1.1 Fossil fuel-fired steam generators, as specified... this appendix to meet the following basic requirements. 2.1 Fossil fuel-fired steam generators. Each fossil fuel-fired steam generator, except as provided in the following subparagraphs, with an annual...

40 CFR Appendix P to Part 51 - Minimum Emission Monitoring Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... respective monitoring requirements are listed below. 1.1.1 Fossil fuel-fired steam generators, as specified... this appendix to meet the following basic requirements. 2.1 Fossil fuel-fired steam generators. Each fossil fuel-fired steam generator, except as provided in the following subparagraphs, with an annual...

40 CFR Appendix P to Part 51 - Minimum Emission Monitoring Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... respective monitoring requirements are listed below. 1.1.1 Fossil fuel-fired steam generators, as specified... this appendix to meet the following basic requirements. 2.1 Fossil fuel-fired steam generators. Each fossil fuel-fired steam generator, except as provided in the following subparagraphs, with an annual...

40 CFR 79.5 - Periodic reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Periodic reporting requirements. 79.5...) REGISTRATION OF FUELS AND FUEL ADDITIVES General Provisions § 79.5 Periodic reporting requirements. (a) Fuel... table: Table 1 to § 79.5—Quarterly Reporting Deadlines Calendar quarter Time period covered Quartely...

27 CFR 19.910 - Application for permit required.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Permits § 19.910 Application for permit required. Any person wishing to establish an alcohol fuel plant shall first make application for and obtain an alcohol fuel producer's permit. The application for a... required by 27 CFR 196.45. Alcohol fuel producers' permits are continuing unless automatically terminated...

10 CFR 503.34 - Inability to comply with applicable environmental requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... requirements. 503.34 Section 503.34 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES... use of alternate fuels in compliance with applicable Federal or state environmental requirements, are... presented as part of a demonstration submitted under § 503.32 (Lack of alternate fuel supply). (2) Prior to...

Alternate aircraft fuels prospects and operational implications

NASA Technical Reports Server (NTRS)

Witcofski, R. D.

1977-01-01

The paper discusses NASA studies of the potentials of coal-derived aviation fuels, specifically synthetic aviation kerosene, liquid methane, and liquid hydrogen. Topics include areas of fuel production, air terminal requirements for aircraft fueling (for liquid hydrogen only), and the performance characteristics of aircraft designed to utilize alternate fuels. Energy requirements associated with the production of each of the three selected fuels are determined, and fuel prices are estimated. Subsonic commercial air transports using liquid hydrogen fuel have been analyzed, and their performance and the performance of aircraft which use commercial aviation kerosene are compared. Environmental and safety issues are considered.

40 CFR 63.7510 - What are my initial compliance requirements and by what date must I conduct them?

Code of Federal Regulations, 2011 CFR

2011-07-01

... subpart, conducting a fuel analysis for each type of fuel burned in your boiler or process heater... sources that burn a single type of fuel, you are exempted from the compliance requirements of conducting a fuel analysis for each type of fuel burned in your boiler or process heater according to § 63.7521 and...

40 CFR 63.7510 - What are my initial compliance requirements and by what date must I conduct them?

Code of Federal Regulations, 2012 CFR

2012-07-01

... subpart, conducting a fuel analysis for each type of fuel burned in your boiler or process heater... sources that burn a single type of fuel, you are exempted from the compliance requirements of conducting a fuel analysis for each type of fuel burned in your boiler or process heater according to § 63.7521 and...

The Analysis of the General Performance and Mechanical Behavior of Unirradiated FeCrAl Alloys Before and After Welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gussev, Maxim N.; Field, Kevin G.; Yamamoto, Yukinori

2016-06-03

The present report summarizes and discusses the preliminary results for the in-depth characterization of the modern, nuclear-grade FeCrAl alloys currently under development. The alloys were designed for enhanced radiation tolerance and weldability, and the research is currently being pursued by the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Last year, seven candidate FeCrAl alloys with well-controlled chemistry and microstructures were designed and produced; welding was performed under well-controlled conditions. The structure and general performance of unirradiated alloys were assessed using standardized and advanced microstructural characterization techniques and mechanical testing. The primary objective is to identify the bestmore » candidate alloy, or at a minimum to identify the contributing factors that increase the weldability and radiation tolerance of FeCrAl alloys, therefore enabling future generations of FeCrAl alloys to deliver better performance parameters. This report is structured so as to describe these critical assessments of the weldability; radiation tolerance will be reported on in later reports from this program.« less

Effect on fast neutron irradiation to 4 dpa at 400{degrees}C on the properties of V-(4-5)Cr-(4-5)Ti alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zinkle, S.J.; Alexander, D.J.; Robertson, J.P.

1997-04-01

Tensile, Charpy impact and electrical resistivity measurements have been performed at ORNL on V-4Cr-4Ti and V-5Cr-5Ti specimens that were prepared at ANL and irradiated in the lithium-bonded X530 experiment in the EBR-II fast reactor. All of the specimens were irradiated to a damage level of about 4 dpa at a temperature of {approximately}400{degrees}C. A significant amount of radiation hardening was evident in both the tensile and Charpy impact tests. The irradiated V-4Cr-4Ti yield strength measured at {approximately}390{degrees}C was >800 MPa, which is more than three times as high as the unirradiated value. The uniform elongations of the irradiated tensile specimensmore » were typically {approximately}1%, with corresponding total elongations of 4-6%. The ductile to brittle transition temperature of the irradiated specimens was less than the unirradiated resistivity, which suggests that hardening associated with interstitial solute pickup was minimal.« less

Topological and morphological analysis of gamma rays irradiated chitosan-poly (vinyl alcohol) blends using atomic force microscopy

NASA Astrophysics Data System (ADS)

Bhatt, Rinkesh; Bisen, D. S.; Bajpai, R.; Bajpai, A. K.

2017-04-01

In the present communication, binary blends of poly (vinyl alcohol) (PVA) and chitosan (CS) were prepared by solution cast method and the roughness parameters of PVA, native CS and CS-PVA blend films were determined using atomic force microscopy (AFM). Moreover, the changes in the morphology of the samples were also investigated after irradiation of gamma rays at absorbed dose of 1 Mrad and 10 Mrad for the scanning areas of 5×5 μm2, 10×10 μm2 and 20×20 μm2. Amplitude, statistical and spatial parameters, including line, 3D and 2D image profiles of the experimental surfaces were examined and compared to un-irradiated samples. For gamma irradiated CS-PVA blends the larger waviness over the surface was found as compared to un-irradiated CS-PVA blends but the values of average roughness for both the films were found almost same. The coefficient of skewness was positive for gamma irradiated CS-PVA blends which revealed the presence of more peaks than valleys on the blend surfaces.

Fracture toughness of irradiated modified 9Cr-1Mo steel

NASA Astrophysics Data System (ADS)

Kim, Sung Ho; Yoon, Ji-Hyun; Ryu, Woo Seog; Lee, Chan Bock; Hong, Jun Hwa

2009-04-01

The effects of irradiation on fracture toughness of modified 9Cr-1Mo steel in the transition region were investigated. Half size precracked Charpy specimens were irradiated up to 1.2 × 10 21n/cm 2 ( E > 0.1 MeV) at 340 °C and 400 °C in the Korean research reactor. The irradiation induced transition temperature shift for a modified 9Cr-1Mo was evaluated by using the Master Curve methodology. The T0 temperature for the unirradiated specimens were measured as -67.7 °C and -72.4 °C from the tests with standard PCVN (precracked charpy V-notch) and half sized PCVN specimens, respectively. The T0 shifts of specimens after irradiation at 340 °C and 400 °C were 70.7 °C and 66.1 °C, respectively. The Weibull slopes for the fracture toughness data obtained from the unirradiated and irradiated modified 9Cr-1Mo steels were determined to confirm the applicability of master curve methodology to modified 9Cr-1Mo steel.

77 FR 45921 - Alaskan Fuel Hauling as a Restricted Category Special Purpose Flight Operation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-02

... operations, each aircraft used to transport fuel will be required to receive FAA certification for the... regulations. The special purpose of Alaskan fuel hauling was considered for aircraft type-certificated under... required for this special purpose. The fuel hauling system must be shown to meet the applicable...

76 FR 6584 - Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-07

... safety review of the aeroplanes fuel system against fuel tank safety standards introduced in Chapter 525... action is required. The assessment showed that a number of modifications to the fuel system are required to mitigate unsafe conditions that could result in potential ignition source within the fuel system...

76 FR 37258 - Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-27

... Aerospace has completed a system safety review of the aeroplanes fuel system against fuel tank safety... the fuel system are required to mitigate unsafe conditions that could result in potential ignition source within the fuel system. We are issuing this AD to require actions to correct the unsafe condition...

40 CFR 600.307-95 - Fuel economy label format requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy label format requirements. 600.307-95 Section 600.307-95 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobile...

40 CFR 600.307-86 - Fuel economy label format requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy label format requirements. 600.307-86 Section 600.307-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobile...

30 CFR 36.50 - Tests of fuel tank.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests of fuel tank. 36.50 Section 36.50 Mineral... MINING PRODUCTS APPROVAL REQUIREMENTS FOR PERMISSIBLE MOBILE DIESEL-POWERED TRANSPORTATION EQUIPMENT Test Requirements § 36.50 Tests of fuel tank. The fuel tank shall be inspected and tested to determine whether: (a...

30 CFR 36.50 - Tests of fuel tank.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tests of fuel tank. 36.50 Section 36.50 Mineral... MINING PRODUCTS APPROVAL REQUIREMENTS FOR PERMISSIBLE MOBILE DIESEL-POWERED TRANSPORTATION EQUIPMENT Test Requirements § 36.50 Tests of fuel tank. The fuel tank shall be inspected and tested to determine whether: (a...

30 CFR 36.50 - Tests of fuel tank.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests of fuel tank. 36.50 Section 36.50 Mineral... MINING PRODUCTS APPROVAL REQUIREMENTS FOR PERMISSIBLE MOBILE DIESEL-POWERED TRANSPORTATION EQUIPMENT Test Requirements § 36.50 Tests of fuel tank. The fuel tank shall be inspected and tested to determine whether: (a...

40 CFR 80.165 - Certification test procedures and standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Detergent Gasoline § 80.165 Certification test... additive is mixed in a test fuel meeting all relevant requirements of § 80.164, including the deposit... control testing. The required test fuel must produce no more than 5% flow restriction in any one injector...

30 CFR 36.50 - Tests of fuel tank.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tests of fuel tank. 36.50 Section 36.50 Mineral... MINING PRODUCTS APPROVAL REQUIREMENTS FOR PERMISSIBLE MOBILE DIESEL-POWERED TRANSPORTATION EQUIPMENT Test Requirements § 36.50 Tests of fuel tank. The fuel tank shall be inspected and tested to determine whether: (a...

40 CFR 86.1506 - Equipment required and specifications; overview.

Code of Federal Regulations, 2014 CFR

2014-07-01

... appear in §§ 86.1509 through 86.1511. (2) Fuel and analytical tests. Fuel requirements for idle exhaust... Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle Test... for performing idle exhaust emission tests on Otto-cycle heavy-duty engines and Otto-cycle light-duty...

30 CFR 36.50 - Tests of fuel tank.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tests of fuel tank. 36.50 Section 36.50 Mineral... MINING PRODUCTS APPROVAL REQUIREMENTS FOR PERMISSIBLE MOBILE DIESEL-POWERED TRANSPORTATION EQUIPMENT Test Requirements § 36.50 Tests of fuel tank. The fuel tank shall be inspected and tested to determine whether: (a...

14 CFR 121.646 - En-route fuel supply: flag and supplemental operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... supply requirements of § 121.333; and (iii) Considering expected wind and other weather conditions. (3..., considering wind and other weather conditions expected, it has the fuel otherwise required by this part and... errors in wind forecasting. In calculating the amount of fuel required by paragraph (b)(1)(i) of this...

14 CFR 121.646 - En-route fuel supply: flag and supplemental operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... supply requirements of § 121.333; and (iii) Considering expected wind and other weather conditions. (3..., considering wind and other weather conditions expected, it has the fuel otherwise required by this part and... errors in wind forecasting. In calculating the amount of fuel required by paragraph (b)(1)(i) of this...

14 CFR 121.646 - En-route fuel supply: flag and supplemental operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... supply requirements of § 121.333; and (iii) Considering expected wind and other weather conditions. (3..., considering wind and other weather conditions expected, it has the fuel otherwise required by this part and... errors in wind forecasting. In calculating the amount of fuel required by paragraph (b)(1)(i) of this...

40 CFR 86.095-23 - Required data.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 19 2012-07-01 2012-07-01 false Required data. 86.095-23 Section 86...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.095-23 Required data. (a)-(b) (c) Emission data—(1) Certification vehicles. The manufacturer shall submit emission data, including, in the case of methanol fuel...

40 CFR 86.095-23 - Required data.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 19 2013-07-01 2013-07-01 false Required data. 86.095-23 Section 86...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.095-23 Required data. (a)-(b) (c) Emission data—(1) Certification vehicles. The manufacturer shall submit emission data, including, in the case of methanol fuel...

40 CFR 86.095-23 - Required data.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 18 2011-07-01 2011-07-01 false Required data. 86.095-23 Section 86...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.095-23 Required data. (a)-(b) (c) Emission data—(1) Certification vehicles. The manufacturer shall submit emission data, including, in the case of methanol fuel...

40 CFR 86.095-23 - Required data.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Required data. 86.095-23 Section 86...-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.095-23 Required data. (a)-(b) (c) Emission data—(1) Certification vehicles. The manufacturer shall submit emission data, including, in the case of methanol fuel...

78 FR 23832 - Labeling Requirements for Alternative Fuels and Alternative Fueled Vehicles

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

... Fuels and Alternative Fueled Vehicles AGENCY: Federal Trade Commission (FTC or Commission). ACTION... Alternative Fuels and Alternative Fueled Vehicles'') to consolidate the FTC's alternative fueled vehicle (AFV...) established federal programs to encourage the development of alternative fuels and alternative fueled vehicles...

Effects of ATR-2 Irradiation to High Fluence on Nine RPV Surveillance Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nanstad, Randy K.; Odette, George R.; Almirall, Nathan

2017-05-01

The reactor pressure vessel (RPV) in a light-water reactor (LWR) represents the first line of defense against a release of radiation in case of an accident. Thus, regulations that govern the operation of commercial nuclear power plants require conservative margins of fracture toughness, both during normal operation and under accident scenarios. In the unirradiated condition, the RPV has sufficient fracture toughness such that failure is implausible under any postulated condition, including pressurized thermal shock (PTS) in pressurized water reactors (PWR). In the irradiated condition, however, the fracture toughness of the RPV may be severely degraded, with the degree of toughnessmore » loss dependent on the radiation sensitivity of the materials. The available embrittlement predictive models and our present understanding of radiation damage are not fully quantitative, and do not treat all potentially significant variables and issues, particularly considering extension of operation to 80y.« less

The non-targeted effects of radiation are perpetuated by exosomes.

PubMed

Al-Mayah, Ammar; Bright, Scott; Chapman, Kim; Irons, Sarah; Luo, Ping; Carter, David; Goodwin, Edwin; Kadhim, Munira

2015-02-01

Exosomes contain cargo material from endosomes, cytosol, plasma membrane and microRNA molecules, they are released by a number of non-cancer and cancer cells into both the extracellular microenvironment and body fluids such as blood plasma. Recently we demonstrated radiation-induced non-targeted effects [NTE: genomic instability (GI) and bystander effects (BE)] are partially mediated by exosomes, particularly the RNA content. However the mechanistic role of exosomes in NTE is yet to be fully understood. The present study used MCF7 cells to characterise the longevity of exosome-induced activity in the progeny of irradiated and unirradiated bystander cells. Exosomes extracted from conditioned media of irradiated and bystander progeny were added to unirradiated cells. Analysis was carried out at 1 and 20/24 population doublings following medium/exosome transfer for DNA/chromosomal damage. Results confirmed exosomes play a significant role in mediating NTE of ionising radiation (IR). This effect was remarkably persistent, observed >20 doublings post-irradiation in the progeny of bystander cells. Additionally, cell progeny undergoing a BE were themselves capable of inducing BE in other cells via exosomes they released. Furthermore we investigated the role of exosome cargo. Culture media from cells exposed to 2 Gy X-rays was subjected to ultracentrifugation and four inoculants prepared, (a) supernatants with exosomes removed, and pellets with (b) exosome proteins denatured, (c) RNA degraded, and (d) a combination of protein-RNA inactivation. These were added to separate populations of unirradiated cells. The BE was partially inhibited when either exosome protein or exosome RNA were inactivated separately, whilst combined RNA-protein inhibition significantly reduced or eliminated the BE. These results demonstrate that exosomes are associated with long-lived signalling of the NTE of IR. Both RNA and protein molecules of exosomes work in a synergistic manner to initiate NTE, spread these effects to naïve cells, and perpetuate GI in the affected cells. Copyright © 2015. Published by Elsevier B.V.

Deep cytoplasmic rearrangements in ventralized Xenopus embryos

NASA Technical Reports Server (NTRS)

Brown, E. E.; Denegre, J. M.; Danilchik, M. V.

1993-01-01

Following fertilization in Xenopus, dramatic rearrangements of the egg cytoplasm relocalize maternally synthesized egg components. During the first cell cycle the vegetal yolk mass rotates relative to the egg surface, toward the sperm entry point (SEP) (J. P. Vincent, G. F. Oster, and J. C. Gerhart, 1986, Dev. Biol. 113, 484-500), while concomitant deep cytoplasmic rearrangements occur in the animal hemisphere (M. V. Danilchik and J. M. Denegre, 1991, Development 111, 845-856). In this paper we examine the role of vegetal yolk mass rotation in producing the animal cytoplasmic rearrangements. We inhibited rotation by uv-irradiating embryos during the first cell cycle, a treatment that yields an extremely ventralized phenotype. Both uv-irradiated embryos and unirradiated control embryos show cytoplasmic rearrangements in the animal hemisphere during the first cell cycle. Cytoplasmic rearrangements on the SEP side of the embryo associated with the path of the sperm pronucleus, plus a swirl on the anti-SEP (dorsal) side, are seen, whether or not yolk mass rotation has occurred. This result suggests a role for the expanding sperm aster in directing animal hemisphere cytoplasmic movements. In unirradiated control embryos the anti-SEP (dorsal) swirl is larger than that in uv-irradiated embryos and often extends into the vegetal hemisphere, consistent with the animal cytoplasm having been pulled dorsally and vegetally by the sliding vegetal yolk mass. Thus the yolk mass rotation may normally enhance the dorsalward cytoplasmic movement, begun by the sperm aster, enough to induce normal axis formation. We extended our observations of unirradiated control and uv-irradiated embryos through early cleavages. The vegetal extent of the anti-SEP (dorsal) swirl pattern seen in control embryos persists through the early cleavage period, such that labeled animal cytoplasm extends deep into dorsal third-tier blastomeres at the 32-cell stage. Significantly, in uv-irradiated embryos, which have not undergone vegetal rotation, most of this labeled material remains more equatorial.

Lack of autologous mixed lymphocyte reaction in patients with chronic lymphocytic leukemia: evidence for autoreactive T-cell dysfunction not correlated with phenotype, karyotype, or clinical status

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, T.; Bloom, M.L.; Dadey, B.

In the present study, there was a complete lack of autologous MLR between responding T cells or T subsets and unirradiated or irradiated leukemic B cells or monocytes in all 20 patients with CLL, regardless of disease status, stage, phenotype, or karyotype of the disease. The stimulating capacity of unirradiated CLL B cells and CLL monocytes or irradiated CLL B cells was significantly depressed as compared to that of respective normal B cells and monocytes in allogeneic MLR. The responding capacity of CLL T cells was also variably lower than that of normal T cells against unirradiated or irradiated normalmore » allogeneic B cells and monocytes. The depressed allogeneic MLR between CLL B cells or CLL monocytes and normal T cells described in the present study could be explained on the basis of a defect in the stimulating antigens of leukemic B cells or monocytes. The decreased allogeneic MLR of CLL T cells might simply be explained by a defect in the responsiveness of T lymphocytes from patients with CLL. However, these speculations do not adequately explain the complete lack of autologous MLR in these patients. When irradiated CLL B cells or irradiated CLL T cells were cocultured with normal T cells and irradiated normal B cells, it was found that there was no suppressor cell activity of CLL B cells or CLL T cells on normal autologous MLR. Our data suggest that the absence or dysfunction of autoreactive T cells within the Tnon-gamma subset account for the lack of autologous MLR in patients with CLL. The possible significance of the autologous MLR, its relationship to in vivo immunoregulatory mechanisms, and the possible role of breakdown of autoimmunoregulation in the oncogenic process of certain lymphoproliferative and autoimmune diseases in man are discussed.« less

40 CFR 86.1230-96 - Test sequence; general requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Petroleum Gas-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.1230-96 Test sequence; general requirements. (a)(1) Gasoline- and methanol-fueled vehicles. The test sequence shown in figure M96-1 of this...

40 CFR 86.1230-96 - Test sequence; general requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Petroleum Gas-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.1230-96 Test sequence; general requirements. (a)(1) Gasoline- and methanol-fueled vehicles. The test sequence shown in figure M96-1 of this...

Improving microbiological safety and maintaining sensory and nutritional quality of pre-cut tomato and carrot by gamma irradiation

NASA Astrophysics Data System (ADS)

Mohácsi-Farkas, Cs.; Nyirő-Fekete, B.; Daood, H.; Dalmadi, I.; Kiskó, G.

2014-06-01

Pre-cut tomato and carrot were irradiated with doses of 1.0, 1.5 and 2 kGy. Unirradiated control and irradiated samples were compared organoleptically by a sensory panel. Microbiological analyses were performed directly after irradiation and during post-irradiation storage for 8 days at 5 °C. Ascorbic acid contents, composition of carotenoids and tocopherols were determined. Statistically significant differences of sensory scores between unirradiated and irradiated samples were observed only in the texture of sliced carrots. Total aerobic viable cell counts have been reduced by about two log cycles with 1.5 kGy dose. Total coliforms and moulds were below the detection limit of 15 CFU/g in the irradiated samples during the refrigerated storage. Yeasts were relatively resistant part of the microbiota of pre-cut tomatoes, but 2 kGy dose reduced them below the detection limit. In pre-cut tomatoes, alpha-tocopherol and some carotenoids seemed to be the most radio-sensitive losing approximately one-third of their original concentrations at the dose of 2 kGy. At this dose tocopherols and the level of ascorbic acid decreased also one-third of the initial level in sliced carrots. Additional experiments were conducted to study the effect of irradiation and storage on the population of Listeria monocytogenes and Listeria innocua artificially inoculated on cut tomato and carrot. Cell numbers of both test organisms decreased by at least two log-cycles as an effect of 1 kGy dose. Our studies confirmed earlier findings on a temporary antilisterial effect of freshly cut carrot tissue. No re-growth of Listeria was observed during the studied storage period. The results of these studies suggest that irradiation with 1 kGy gamma rays could improve sufficiently the microbiological safety of the investigated pre-cut produce to satisfy the requirement of low microbial raw diets with acceptable nutritional quality and without diminishing significantly the organoleptic parameters of the commodities.

40 CFR 600.006-08 - Data and information requirements for fuel economy vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Data and information requirements for fuel economy vehicles. 600.006-08 Section 600.006-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

40 CFR 600.006-89 - Data and information requirements for fuel economy vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Data and information requirements for fuel economy vehicles. 600.006-89 Section 600.006-89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

40 CFR 600.006-87 - Data and information requirements for fuel economy vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Data and information requirements for fuel economy vehicles. 600.006-87 Section 600.006-87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

40 CFR 600.006-86 - Data and information requirements for fuel economy vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Data and information requirements for fuel economy vehicles. 600.006-86 Section 600.006-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

40 CFR 80.1642 - Sampling and testing requirements for producers and importers of denatured fuel ethanol and other...

Code of Federal Regulations, 2014 CFR

2014-07-01

... producers and importers of denatured fuel ethanol and other oxygenates for use by oxygenate blenders. 80... requirements for producers and importers of denatured fuel ethanol and other oxygenates for use by oxygenate blenders. Beginning January 1, 2017, producers and importers of denatured fuel ethanol (DFE) and other...

40 CFR 80.177 - Certification test fuels for use with the alternative test procedures and standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Certification test fuels for use with... Detergent Gasoline § 80.177 Certification test fuels for use with the alternative test procedures and standards. (a) General requirements. This section provides specifications for the test fuels required in...

40 CFR 600.306-12 - Fuel economy label-special requirements for compressed natural gas vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Fuel economy label-special requirements for compressed natural gas vehicles. 600.306-12 Section 600.306-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Labeling §...

40 CFR 600.306-12 - Fuel economy label-special requirements for compressed natural gas vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Fuel economy label-special requirements for compressed natural gas vehicles. 600.306-12 Section 600.306-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Labeling §...

40 CFR 600.306-12 - Fuel economy label-special requirements for compressed natural gas vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Fuel economy label-special requirements for compressed natural gas vehicles. 600.306-12 Section 600.306-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Labeling §...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2014 CFR

2014-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2010 CFR

2010-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2012 CFR

2012-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2011 CFR

2011-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

46 CFR 62.35-40 - Fuel systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Fuel systems. 62.35-40 Section 62.35-40 Shipping COAST... Requirements for Specific Types of Automated Vital Systems § 62.35-40 Fuel systems. (a) Level alarms. Where high or low fuel tank level alarms are required, they must be located to allow the operator adequate...

46 CFR 62.35-40 - Fuel systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Fuel systems. 62.35-40 Section 62.35-40 Shipping COAST... Requirements for Specific Types of Automated Vital Systems § 62.35-40 Fuel systems. (a) Level alarms. Where high or low fuel tank level alarms are required, they must be located to allow the operator adequate...

46 CFR 62.35-40 - Fuel systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Fuel systems. 62.35-40 Section 62.35-40 Shipping COAST... Requirements for Specific Types of Automated Vital Systems § 62.35-40 Fuel systems. (a) Level alarms. Where high or low fuel tank level alarms are required, they must be located to allow the operator adequate...

46 CFR 62.35-40 - Fuel systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Fuel systems. 62.35-40 Section 62.35-40 Shipping COAST... Requirements for Specific Types of Automated Vital Systems § 62.35-40 Fuel systems. (a) Level alarms. Where high or low fuel tank level alarms are required, they must be located to allow the operator adequate...

40 CFR 80.570 - What labeling requirements apply to retailers and wholesale purchaser-consumers of diesel fuel...

Code of Federal Regulations, 2010 CFR

2010-07-01

... retailers and wholesale purchaser-consumers of diesel fuel beginning June 1, 2006? 80.570 Section 80.570... Marine Fuel Labeling Requirements § 80.570 What labeling requirements apply to retailers and wholesale..., any retailer or wholesale purchaser-consumer who sells, dispenses, or offers for sale or dispensing...

40 CFR 86.106-96 - Equipment required; overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

... contains procedures for exhaust emission tests on petroleum-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled light-duty vehicles and light-duty trucks, and for evaporative emission tests on gasoline-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled...

40 CFR 86.106-96 - Equipment required; overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... contains procedures for exhaust emission tests on petroleum-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled light-duty vehicles and light-duty trucks, and for evaporative emission tests on gasoline-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled...

40 CFR 86.106-96 - Equipment required; overview.

Code of Federal Regulations, 2014 CFR

2014-07-01

... contains procedures for exhaust emission tests on petroleum-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled light-duty vehicles and light-duty trucks, and for evaporative emission tests on gasoline-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled...

40 CFR 86.106-96 - Equipment required; overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

... contains procedures for exhaust emission tests on petroleum-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled light-duty vehicles and light-duty trucks, and for evaporative emission tests on gasoline-fueled, natural gas-fueled, liquefied petroleum gas-fueled, and methanol-fueled...

High Performance Fuel Cell and Electrolyzer Membrane Electrode Assemblies (MEAs) for Space Energy Storage Systems

NASA Technical Reports Server (NTRS)

Valdez, Thomas I.; Billings, Keith J.; Kisor, Adam; Bennett, William R.; Jakupca, Ian J.; Burke, Kenneth; Hoberecht, Mark A.

2012-01-01

Regenerative fuel cells provide a pathway to energy storage system development that are game changers for NASA missions. The fuel cell/ electrolysis MEA performance requirements 0.92 V/ 1.44 V at 200 mA/cm2 can be met. Fuel Cell MEAs have been incorporated into advanced NFT stacks. Electrolyzer stack development in progress. Fuel Cell MEA performance is a strong function of membrane selection, membrane selection will be driven by durability requirements. Electrolyzer MEA performance is catalysts driven, catalyst selection will be driven by durability requirements. Round Trip Efficiency, based on a cell performance, is approximately 65%.

7 CFR 2903.5 - Matching requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., DEPARTMENT OF AGRICULTURE BIODIESEL FUEL EDUCATION PROGRAM General Information § 2903.5 Matching requirements. There are no matching funds requirements for the Biodiesel Fuel Education Program and matching resources...

7 CFR 2903.5 - Matching requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., DEPARTMENT OF AGRICULTURE BIODIESEL FUEL EDUCATION PROGRAM General Information § 2903.5 Matching requirements. There are no matching funds requirements for the Biodiesel Fuel Education Program and matching resources...

7 CFR 2903.5 - Matching requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., DEPARTMENT OF AGRICULTURE BIODIESEL FUEL EDUCATION PROGRAM General Information § 2903.5 Matching requirements. There are no matching funds requirements for the Biodiesel Fuel Education Program and matching resources...

7 CFR 2903.5 - Matching requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., DEPARTMENT OF AGRICULTURE BIODIESEL FUEL EDUCATION PROGRAM General Information § 2903.5 Matching requirements. There are no matching funds requirements for the Biodiesel Fuel Education Program and matching resources...

7 CFR 2903.5 - Matching requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., DEPARTMENT OF AGRICULTURE BIODIESEL FUEL EDUCATION PROGRAM General Information § 2903.5 Matching requirements. There are no matching funds requirements for the Biodiesel Fuel Education Program and matching resources...

Pre-irradiation testing and analysis to support the LWRS Hybrid SiC-CMC-Zircaloy-04 unfueled rodlet irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isabella J van Rooyen

2012-09-01

Nuclear fuel performance is a significant driver of nuclear power plant operational performance, safety, economics and waste disposal requirements. The Advanced Light Water Reactor (LWR) Nuclear Fuel Development Pathway focuses on improving the scientific knowledge basis to enable the development of high-performance, high burn-up fuels with improved safety and cladding integrity and improved nuclear fuel cycle economics. To achieve significant improvements, fundamental changes are required in the areas of nuclear fuel composition, cladding integrity, and fuel/cladding interaction.

Pre-irradiation testing and analysis to support the LWRS Hybrid SiC-CMC-Zircaloy-04 unfueled rodlet irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isabella J van Rooyen

2013-01-01

Nuclear fuel performance is a significant driver of nuclear power plant operational performance, safety, economics and waste disposal requirements. The Advanced Light Water Reactor (LWR) Nuclear Fuel Development Pathway focuses on improving the scientific knowledge basis to enable the development of high-performance, high burn-up fuels with improved safety and cladding integrity and improved nuclear fuel cycle economics. To achieve significant improvements, fundamental changes are required in the areas of nuclear fuel composition, cladding integrity, and fuel/cladding interaction.

Requirements to the procedure and stages of innovative fuel development

NASA Astrophysics Data System (ADS)

Troyanov, V.; Zabudko, L.; Grachyov, A.; Zhdanova, O.

2016-04-01

According to the accepted current understanding under the nuclear fuel we will consider the assembled active zone unit (Fuel assembly) with its structural elements, fuel rods, pellet column, structural materials of fuel rods and fuel assemblies. The licensing process includes justification of safe application of the proposed modifications, including design-basis and experimental justification of the modified items under normal operating conditions and in violation of normal conditions, including accidents as well. Besides the justification of modified units itself, it is required to show the influence of modifications on the performance and safety of the other Reactor Unit’ and Nuclear Plant’ elements (e.g. burst can detection system, transportation and processing operations during fuel handling), as well as to justify the new standards of fuel storage etc. Finally, the modified fuel should comply with the applicable regulations, which often becomes a very difficult task, if only because those regulations, such as the NP-082-07, are not covered modification issues. Making amendments into regulations can be considered as the only solution, but the process is complicated and requires deep grounds for amendments. Some aspects of licensing new nuclear fuel are considered the example of mixed nitride uranium -plutonium fuel application for the BREST reactor unit.

Designing the microturbine engine for waste-derived fuels.

PubMed

Seljak, Tine; Katrašnik, Tomaž

2016-01-01

Presented paper deals with adaptation procedure of a microturbine (MGT) for exploitation of refuse derived fuels (RDF). RDF often possess significantly different properties than conventional fuels and usually require at least some adaptations of internal combustion systems to obtain full functionality. With the methodology, developed in the paper it is possible to evaluate the extent of required adaptations by performing a thorough analysis of fuel combustion properties in a dedicated experimental rig suitable for testing of wide-variety of waste and biomass derived fuels. In the first part key turbine components are analyzed followed by cause and effect analysis of interaction between different fuel properties and design parameters of the components. The data are then used to build a dedicated test system where two fuels with diametric physical and chemical properties are tested - liquefied biomass waste (LW) and waste tire pyrolysis oil (TPO). The analysis suggests that exploitation of LW requires higher complexity of target MGT system as stable combustion can be achieved only with regenerative thermodynamic cycle, high fuel preheat temperatures and optimized fuel injection nozzle. Contrary, TPO requires less complex MGT design and sufficient operational stability is achieved already with simple cycle MGT and conventional fuel system. The presented approach of testing can significantly reduce the extent and cost of required adaptations of commercial system as pre-selection procedure of suitable MGT is done in developed test system. The obtained data can at the same time serve as an input for fine-tuning the processes for RDF production. Copyright © 2015. Published by Elsevier Ltd.

Oil cooling system for a gas turbine engine

NASA Technical Reports Server (NTRS)

Coffinberry, G. A.; Kast, H. B. (Inventor)

1977-01-01

A gas turbine engine fuel delivery and control system is provided with means to recirculate all fuel in excess fuel control requirements back to the aircraft fuel tank. This increases the fuel pump heat sink and decreases the pump temperature rise without the addition of valving other than normally employed. A fuel/oil heat exchanger and associated circuitry is provided to maintain the hot engine oil in heat exchange relationship with the cool engine fuel. Where anti-icing of the fuel filter is required, means are provided to maintain the fuel temperature entering the filter at or above a minimum level to prevent freezing thereof. In one embodiment, a divider valve is provided to take all excess fuel from either upstream or downstream of the fuel filter and route it back to the tanks, the ratio of upstream to downstream extraction being a function of fuel pump discharge pressure.

10 CFR 73.35 - Requirements for physical protection of irradiated reactor fuel (100 grams or less) in transit.

Code of Federal Regulations, 2014 CFR

2014-01-01

... fuel (100 grams or less) in transit. 73.35 Section 73.35 Energy NUCLEAR REGULATORY COMMISSION... Transit § 73.35 Requirements for physical protection of irradiated reactor fuel (100 grams or less) in... quantity of irradiated reactor fuel weighing 100 grams (0.22 pounds) or less in net weight of irradiated...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2014 CFR

2014-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2013 CFR

2013-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2012 CFR

2012-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2011 CFR

2011-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

Development Status of PEM Non-Flow-Through Fuel Cell System Technology for NASA Applications

NASA Technical Reports Server (NTRS)

Hoberecht, Mark A.; Jakupca, Ian J.

2011-01-01

Today s widespread development of proton-exchange-membrane (PEM) fuel cell technology for commercial users owes its existence to NASA, where fuel cell technology saw its first applications. Beginning with the early Gemini and Apollo programs, and continuing to this day with the Shuttle Orbiter program, fuel cells have been a primary source of electrical power for many NASA missions. This is particularly true for manned missions, where astronauts are able to make use of the by-product of the fuel cell reaction, potable water. But fuel cells also offer advantages for unmanned missions, specifically when power requirements exceed several hundred watts and primary batteries are not a viable alternative. In recent years, NASA s Exploration Technology Development Program (ETDP) funded the development of fuel cell technology for applications that provide both primary power and regenerative fuel cell energy storage for planned Exploration missions that involved a return to the moon. Under this program, the Altair Lunar Lander was a mission requiring fuel cell primary power. There were also various Lunar Surface System applications requiring regenerative fuel cell energy storage, in which a fuel cell and electrolyzer combine to form an energy storage system with hydrogen, oxygen, and water as common reactants. Examples of these systems include habitat modules and large rovers. In FY11, the ETDP has been replaced by the Enabling Technology Development and Demonstration Program (ETDDP), with many of the same technology goals and requirements applied against NASA s revised Exploration portfolio.

Metallic Fuel Casting Development and Parameter Optimization Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

R.S. Fielding; J. Crapps; C. Unal

One of the advantages of metallic fuel is the abilility to cast the fuel slugs to near net shape with little additional processing. However, the high aspect ratio of the fuel is not ideal for casting. EBR-II fuel was cast using counter gravity injection casting (CGIC) but, concerns have been raised concerning the feasibility of this process for americium bearing alloys. The Fuel Cycle Research and Development program has begun developing gravity casting techniques suitable for fuel production. Compared to CGIC gravity casting does not require a large heel that then is recycled, does not require application of a vacuummore » during melting, and is conducive to re-usable molds. Development has included fabrication of two separate benchscale, approximately 300 grams, systems. To shorten development time computer simulations have been used to ensure mold and crucible designs are feasible and to identify which fluid properties most affect casting behavior and therefore require more characterization.« less

LH2 airport requirements study

NASA Technical Reports Server (NTRS)

Brewer, G. D. (Editor)

1976-01-01

A preliminary assessment of the facilities and equipment which will be required at a representative airport is provided so liquid hydrogen LH2 can be used as fuel in long range transport aircraft in 1995-2000. A complete facility was conceptually designed, sized to meet the projected air traffic requirement. The facility includes the liquefaction plant, LH2, storage capability, and LH2 fuel handling system. The requirements for ground support and maintenance for the LH2 fueled aircraft were analyzed. An estimate was made of capital and operating costs which might be expected for the facility. Recommendations were made for design modifications to the reference aircraft, reflecting results of the analysis of airport fuel handling requirements, and for a program of additional technology development for air terminal related items.

30 CFR 75.1901 - Diesel fuel requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

....1901 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1901 Diesel fuel... fuel purchased for use in diesel-powered equipment underground meets these requirements. (b) Flammable...

30 CFR 75.1901 - Diesel fuel requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

....1901 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1901 Diesel fuel... fuel purchased for use in diesel-powered equipment underground meets these requirements. (b) Flammable...

40 CFR 80.526 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.526 [Reserved] ...

40 CFR 80.523 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.523 [Reserved] ...

40 CFR 86.1530 - Test sequence; general requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and... Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle...

Fuels Registration, Reporting, and Compliance Help

EPA Pesticide Factsheets

Information about the requirements for registration and health effects testing of new fuels or fuel additives and mandatory registration for fuels reporting and about mandatory reporting forms for parties regulated under EPA fuel programs.

Irradiation performance of U-Mo monolithic fuel

DOE PAGES

Meyer, M. K.; Gan, J.; Jue, J. F.; ...

2014-04-01

High-performance research reactors require fuel that operates at high specific power to high fission density, but at relatively low temperatures. Research reactor fuels are designed for efficient heat rejection, and are composed of assemblies of thin-plates clad in aluminum alloy. The development of low-enriched fuels to replace high-enriched fuels for these reactors requires a substantially increased uranium density in the fuel to offset the decrease in enrichment. Very few fuel phases have been identified that have the required combination of very-high uranium density and stable fuel behavior at high burnup. U-Mo alloys represent the best known tradeoff in these properties.more » Testing of aluminum matrix U-Mo aluminum matrix dispersion fuel revealed a pattern of breakaway swelling behavior at intermediate burnup, related to the formation of a molybdenum stabilized high aluminum intermetallic phase that forms during irradiation. In the case of monolithic fuel, this issue was addressed by eliminating, as much as possible, the interfacial area between U-Mo and aluminum. Based on scoping irradiation test data, a fuel plate system composed of solid U-10Mo fuel meat, a zirconium diffusion barrier, and Al6061 cladding was selected for development. Developmental testing of this fuel system indicates that it meets core criteria for fuel qualification, including stable and predictable swelling behavior, mechanical integrity to high burnup, and geometric stability. In addition, the fuel exhibits robust behavior during power-cooling mismatch events under irradiation at high power.« less

IRRADIATION PERFORMANCE OF U-Mo MONOLITHIC FUEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

M.K. Meyer; J. Gan; J.-F. Jue

2014-04-01

High-performance research reactors require fuel that operates at high specific power to high fission density, but at relatively low temperatures. Research reactor fuels are designed for efficient heat rejection, and are composed of assemblies of thin-plates clad in aluminum alloy. The development of low-enriched fuels to replace high-enriched fuels for these reactors requires a substantially increased uranium density in the fuel to offset the decrease in enrichment. Very few fuel phases have been identified that have the required combination of very-high uranium density and stable fuel behavior at high burnup. UMo alloys represent the best known tradeoff in these properties.more » Testing of aluminum matrix U-Mo aluminum matrix dispersion fuel revealed a pattern of breakaway swelling behavior at intermediate burnup, related to the formation of a molybdenum stabilized high aluminum intermetallic phase that forms during irradiation. In the case of monolithic fuel, this issue was addressed by eliminating, as much as possible, the interfacial area between U-Mo and aluminum. Based on scoping irradiation test data, a fuel plate system composed of solid U-10Mo fuel meat, a zirconium diffusion barrier, and Al6061 cladding was selected for development. Developmental testing of this fuel system indicates that it meets core criteria for fuel qualification, including stable and predictable swelling behavior, mechanical integrity to high burnup, and geometric stability. In addition, the fuel exhibits robust behavior during power-cooling mismatch events under irradiation at high power.« less

76 FR 31462 - Airworthiness Directives; The Boeing Company Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

... determine if a certain fuel pump housing electrical connector is installed. The existing AD also requires a... procedures for disabling certain fuel pump electrical circuits following failure of a fuel pump housing electrical connector if applicable. The existing AD also requires the deactivation of certain fuel tanks or...

Hydrocarbon Fuel Thermal Performance Modeling based on Systematic Measurement and Comprehensive Chromatographic Analysis

DTIC Science & Technology

2016-07-27

is a common requirement for aircraft, rockets , and hypersonic vehicles. The Aerospace Fuels Quality Test and Model Development (AFQTMoDev) project...was initiated to mature fuel quality assurance practices for rocket grade kerosene, thereby ensuring operational readiness of conventional and...and reliability, is a common requirement for aircraft, rockets , and hypersonic vehicles. The Aerospace Fuels Quality Test and Model Development

Oil cooling system for a gas turbine engine

NASA Technical Reports Server (NTRS)

Coffinberry, G. A.; Kast, H. B. (Inventor)

1977-01-01

A gas turbine engine fuel delivery and control system is provided with means to recirculate all fuel in excess of fuel control requirements back to aircraft fuel tank, thereby increasing the fuel pump heat sink and decreasing the pump temperature rise without the addition of valving other than that normally employed. A fuel/oil heat exchanger and associated circuitry is provided to maintain the hot engine oil in heat exchange relationship with the cool engine fuel. Where anti-icing of the fuel filter is required, means are provided to maintain the fuel temperature entering the filter at or above a minimum level to prevent freezing thereof. Fluid circuitry is provided to route hot engine oil through a plurality of heat exchangers disposed within the system to provide for selective cooling of the oil.

Consideration of Fuel Requirements for Supersonic Transport Operation

NASA Technical Reports Server (NTRS)

Stickle, Joseph W.

1965-01-01

An analysis of the interaction of operational environment and aircraft characteristics of the supersonic transport (SST) in the areas of design-range and reserve-fuel requirements has been made. Design-range requirements are considered in relation to the effects of wind, temperature, flight-level assignment, and payload variation. An approach toward combining en route and holding reserve requirements while maintaining protection equivalent to that provided subsonic jet transport operations by the present civil air regulation en route plus holding reserves is given. This approach results in a savings in reserve fuel over that required by separate requirements.

40 CFR 60.4207 - What fuel requirements must I meet if I am an owner or operator of a stationary CI internal...

Code of Federal Regulations, 2011 CFR

2011-07-01

... am an owner or operator of a stationary CI internal combustion engine subject to this subpart? 60... Compression Ignition Internal Combustion Engines Fuel Requirements for Owners and Operators § 60.4207 What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion...

40 CFR 60.4207 - What fuel requirements must I meet if I am an owner or operator of a stationary CI internal...

Code of Federal Regulations, 2010 CFR

2010-07-01

... am an owner or operator of a stationary CI internal combustion engine subject to this subpart? 60... Compression Ignition Internal Combustion Engines Fuel Requirements for Owners and Operators § 60.4207 What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion...

40 CFR 60.4207 - What fuel requirements must I meet if I am an owner or operator of a stationary CI internal...

Code of Federal Regulations, 2012 CFR

2012-07-01

... am an owner or operator of a stationary CI internal combustion engine subject to this subpart? 60... Compression Ignition Internal Combustion Engines Fuel Requirements for Owners and Operators § 60.4207 What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion...

40 CFR 60.4207 - What fuel requirements must I meet if I am an owner or operator of a stationary CI internal...

Code of Federal Regulations, 2013 CFR

2013-07-01

... am an owner or operator of a stationary CI internal combustion engine subject to this subpart? 60... Compression Ignition Internal Combustion Engines Fuel Requirements for Owners and Operators § 60.4207 What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion...

40 CFR 60.4207 - What fuel requirements must I meet if I am an owner or operator of a stationary CI internal...

Code of Federal Regulations, 2014 CFR

2014-07-01

... am an owner or operator of a stationary CI internal combustion engine subject to this subpart? 60... Compression Ignition Internal Combustion Engines Fuel Requirements for Owners and Operators § 60.4207 What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion...

Study of the application of hydrogen fuel to long-range subsonic transport aircraft. Volume 1: Summary

NASA Technical Reports Server (NTRS)

Brewer, G. D.; Morris, R. E.; Lange, R. H.; Moore, J. W.

1975-01-01

The feasibility of using liquid hydrogen as fuel in advanced designs of long range, subsonic transport aircraft is assessed. Both passenger and cargo type aircraft are investigated. Comparisons of physical, performance, and economic parameters of the LH2 fueled designs with conventionally fueled aircraft are presented. Design studies are conducted to determine appropriate characteristics for the hydrogen related systems required on board the aircraft. These studies included consideration of material, structural, and thermodynamic requirements of the cryogenic fuel tanks and fuel systems with the structural support and thermal protection systems.

Stress corrosion crack initiation of Zircaloy-4 cladding tubes in an iodine vapor environment during creep, relaxation, and constant strain rate tests

NASA Astrophysics Data System (ADS)

Jezequel, T.; Auzoux, Q.; Le Boulch, D.; Bono, M.; Andrieu, E.; Blanc, C.; Chabretou, V.; Mozzani, N.; Rautenberg, M.

2018-02-01

During accidental power transient conditions with Pellet Cladding Interaction (PCI), the synergistic effect of the stress and strain imposed on the cladding by thermal expansion of the fuel, and corrosion by iodine released as a fission product, may lead to cladding failure by Stress Corrosion Cracking (SCC). In this study, internal pressure tests were conducted on unirradiated cold-worked stress-relieved Zircaloy-4 cladding tubes in an iodine vapor environment. The goal was to investigate the influence of loading type (constant pressure tests, constant circumferential strain rate tests, or constant circumferential strain tests) and test temperature (320, 350, or 380 °C) on iodine-induced stress corrosion cracking (I-SCC). The experimental results obtained with different loading types were consistent with each other. The apparent threshold hoop stress for I-SCC was found to be independent of the test temperature. SEM micrographs of the tested samples showed many pits distributed over the inner surface, which tended to coalesce into large pits in which a microcrack could initiate. A model for the time-to-failure of a cladding tube was developed using finite element simulations of the viscoplastic mechanical behavior of the material and a modified Kachanov's damage growth model. The times-to-failure predicted by this model are consistent with the experimental data.

Modernization at the Y-12 National Security Complex: A Case for Additional Experimental Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornbury, M. L.; Juarez, C.; Krass, A. W.

Efforts are underway at the Y-12 National Security Complex (Y-12) to modernize the recovery, purification, and consolidation of un-irradiated, highly enriched uranium metal. Successful integration of advanced technology such as Electrorefining (ER) eliminates many of the intermediate chemistry systems and processes that are the current and historical basis of the nuclear fuel cycle at Y-12. The cost of operations, the inventory of hazardous chemicals, and the volume of waste are significantly reduced by ER. It also introduces unique material forms and compositions related to the chemistry of chloride salts for further consideration in safety analysis and engineering. The work hereinmore » briefly describes recent investigations of nuclear criticality for 235UO2Cl2 (uranyl chloride) and 6LiCl (lithium chloride) in aqueous solution. Of particular interest is the minimum critical mass of highly enriched uranium as a function of the molar ratio of 6Li to 235U. The work herein also briefly describes recent investigations of nuclear criticality for 235U metal reflected by salt mixtures of 6LiCl or 7LiCl (lithium chloride), KCl (potassium chloride), and 235UCl3 or 238UCl3 (uranium tri-chloride). Computational methods for analysis of nuclear criticality safety and published nuclear data are employed in the absence of directly relevant experimental criticality benchmarks.« less

40 CFR 80.1654 - California gasoline requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false California gasoline requirements. 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur § 80.1654 California gasoline requirements. (a) California gasoline exemption. California gasoline that complies with all the requirements of...

40 CFR 60.40b - Applicability and delegation of authority.

Code of Federal Regulations, 2012 CFR

2012-07-01

... applicability requirements under subpart D (Standards of performance for fossil-fuel-fired steam generators... meeting the applicability requirements under subpart D (Standards of performance for fossil-fuel-fired... fossil fuel. If the affected facility (i.e. heat recovery steam generator) is subject to this subpart...

40 CFR 60.40b - Applicability and delegation of authority.

Code of Federal Regulations, 2014 CFR

2014-07-01

... applicability requirements under subpart D (Standards of performance for fossil-fuel-fired steam generators... meeting the applicability requirements under subpart D (Standards of performance for fossil-fuel-fired... fossil fuel. If the affected facility (i.e. heat recovery steam generator) is subject to this subpart...

40 CFR 60.40b - Applicability and delegation of authority.

Code of Federal Regulations, 2011 CFR

2011-07-01

... applicability requirements under subpart D (Standards of performance for fossil-fuel-fired steam generators... meeting the applicability requirements under subpart D (Standards of performance for fossil-fuel-fired...) heat input of fossil fuel. If the heat recovery steam generator is subject to this subpart, only...

40 CFR 60.40b - Applicability and delegation of authority.

Code of Federal Regulations, 2010 CFR

2010-07-01

... applicability requirements under subpart D (Standards of performance for fossil-fuel-fired steam generators... meeting the applicability requirements under subpart D (Standards of performance for fossil-fuel-fired...) heat input of fossil fuel. If the heat recovery steam generator is subject to this subpart, only...

40 CFR 60.40b - Applicability and delegation of authority.

Code of Federal Regulations, 2013 CFR

2013-07-01

... applicability requirements under subpart D (Standards of performance for fossil-fuel-fired steam generators... meeting the applicability requirements under subpart D (Standards of performance for fossil-fuel-fired... fossil fuel. If the affected facility (i.e. heat recovery steam generator) is subject to this subpart...

40 CFR 86.306-79 - Equipment required and specifications; overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test... for both gasoline-fueled and Diesel engine gaseous emission tests. Generally, the equipment required...

40 CFR 86.306-79 - Equipment required and specifications; overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test... for both gasoline-fueled and Diesel engine gaseous emission tests. Generally, the equipment required...

40 CFR 86.306-79 - Equipment required and specifications; overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test... for both gasoline-fueled and Diesel engine gaseous emission tests. Generally, the equipment required...

40 CFR 86.306-79 - Equipment required and specifications; overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test... for both gasoline-fueled and Diesel engine gaseous emission tests. Generally, the equipment required...

Alternate-Fueled Combustor-Sector Performance. Parts A and B; (A) Combustor Performance; (B) Combustor Emissions

NASA Technical Reports Server (NTRS)

Shouse, D. T.; Hendricks, R. C.; Lynch, A.; Frayne, C. W.; Stutrud, J. S.; Corporan, E.; Hankins, T.

2012-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F(2008) or ASTM D 7566 (2010) standards, respectively, and are classified as "drop-in" fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are certified individually on the basis of processing and assumed to be feedstock agnostic. Adherence to alternate fuels and fuel blends requires "smart fueling systems" or advanced fuel-flexible systems, including combustors and engines, without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance (Part A) and emissions and particulates (Part B) combustor sector data. The data are for nominal inlet conditions at 225 psia and 800 F (1.551 MPa and 700 K), for synthetic-paraffinic-kerosene- (SPK-) type (Fisher-Tropsch (FT)) fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling. Assessments are made of the change in combustor efficiency, wall temperatures, emissions, and luminosity with SPK of 0%, 50%, and 100% fueling composition at 3% combustor pressure drop. The performance results (Part A) indicate no quantifiable differences in combustor efficiency, a general trend to lower liner and higher core flow temperatures with increased FT fuel blends. In general, emissions data (Part B) show little differences, but with percent increase in FT-SPK-type fueling, particulate emissions and wall temperatures are less than with baseline JP-8. High-speed photography illustrates both luminosity and combustor dynamic flame characteristics.

Simulation modelling for new gas turbine fuel controller creation.

NASA Astrophysics Data System (ADS)

Vendland, L. E.; Pribylov, V. G.; Borisov, Yu A.; Arzamastsev, M. A.; Kosoy, A. A.

2017-11-01

State of the art gas turbine fuel flow control systems are based on throttle principle. Major disadvantage of such systems is that they require high pressure fuel intake. Different approach to fuel flow control is to use regulating compressor. And for this approach because of controller and gas turbine interaction a specific regulating compressor is required. Difficulties emerge as early as the requirement definition stage. To define requirements for new object, his properties must be known. Simulation modelling helps to overcome these difficulties. At the requirement definition stage the most simplified mathematical model is used. Mathematical models will get more complex and detailed as we advance in planned work. If future adjusting of regulating compressor physical model to work with virtual gas turbine and physical control system is planned.

Evaluation of a Passive Heat Exchanger Based Cooling System for Fuel Cell Applications

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.; Burke, Kenneth A.

2011-01-01

Fuel cell cooling is conventionally performed with an actively controlled, dedicated coolant loop that exchanges heat with a separate external cooling loop. To simplify this system the concept of directly cooling a fuel cell utilizing a coolant loop with a regenerative heat exchanger to preheat the coolant entering the fuel cell with the coolant exiting the fuel cell was analyzed. The preheating is necessary to minimize the temperature difference across the fuel cell stack. This type of coolant system would minimize the controls needed on the coolant loop and provide a mostly passive means of cooling the fuel cell. The results indicate that an operating temperature of near or greater than 70 C is achievable with a heat exchanger effectiveness of around 90 percent. Of the heat exchanger types evaluated with the same type of fluid on the hot and cold side, a counter flow type heat exchanger would be required which has the possibility of achieving the required effectiveness. The number of heat transfer units required by the heat exchanger would be around 9 or greater. Although the analysis indicates the concept is feasible, the heat exchanger design would need to be developed and optimized for a specific fuel cell operation in order to achieve the high effectiveness value required.

76 FR 79051 - Airworthiness Directives; Lycoming Engines, Fuel Injected Reciprocating Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-21

... models requiring inspections. We are issuing this AD to prevent failure of the fuel injector fuel lines... to prevent failure of the fuel injector fuel lines that would allow fuel to spray into the engine... injector nozzles, and replace as necessary any fuel injector fuel line and clamp that does not meet all...

40 CFR 80.528-80.529 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

....528-80.529 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements §§ 80.528-80.529...

40 CFR 86.1542 - Information required.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Heavy-Duty Engines, New Otto-Cycle Light-Duty Trucks, and New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle Test Procedures...

78 FR 24689 - Airworthiness Directives; PILATUS Aircraft Ltd. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

... an emergency fuel control system adjustment test. We are issuing this proposed AD to require actions... Emergency Fuel Control System (FCS). For the reason described above, this AD requires the implementation and...; and PILATUS PC-7 Maintenance Manual, Emergency Fuel Control System--Adjustment/Test, 76-20-00, pages...

14 CFR Special Federal Aviation... - Fuel Tank System Fault Tolerance Evaluation Requirements

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel Tank System Fault Tolerance Evaluation Requirements Federal Special Federal Aviation Regulation No. 88 Aeronautics and Space FEDERAL AVIATION..., SFAR No. 88 Special Federal Aviation Regulation No. 88—Fuel Tank System Fault Tolerance Evaluation...

14 CFR Special Federal Aviation... - Fuel Tank System Fault Tolerance Evaluation Requirements

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel Tank System Fault Tolerance Evaluation Requirements Federal Special Federal Aviation Regulation No. 88 Aeronautics and Space FEDERAL AVIATION..., SFAR No. 88 Special Federal Aviation Regulation No. 88—Fuel Tank System Fault Tolerance Evaluation...

14 CFR Special Federal Aviation... - Fuel Tank System Fault Tolerance Evaluation Requirements

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel Tank System Fault Tolerance Evaluation Requirements Federal Special Federal Aviation Regulation No. 88 Aeronautics and Space FEDERAL AVIATION..., SFAR No. 88 Special Federal Aviation Regulation No. 88—Fuel Tank System Fault Tolerance Evaluation...

14 CFR Special Federal Aviation... - Fuel Tank System Fault Tolerance Evaluation Requirements

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel Tank System Fault Tolerance Evaluation Requirements Federal Special Federal Aviation Regulation No. 88 Aeronautics and Space FEDERAL AVIATION..., SFAR No. 88 Special Federal Aviation Regulation No. 88—Fuel Tank System Fault Tolerance Evaluation...

14 CFR Special Federal Aviation... - Fuel Tank System Fault Tolerance Evaluation Requirements

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel Tank System Fault Tolerance Evaluation Requirements Federal Special Federal Aviation Regulation No. 88 Aeronautics and Space FEDERAL AVIATION..., SFAR No. 88 Special Federal Aviation Regulation No. 88—Fuel Tank System Fault Tolerance Evaluation...

40 CFR 75.48 - Petition for an alternative monitoring system.

Code of Federal Regulations, 2011 CFR

2011-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

40 CFR 75.48 - Petition for an alternative monitoring system.

Code of Federal Regulations, 2014 CFR

2014-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

40 CFR 75.48 - Petition for an alternative monitoring system.

Code of Federal Regulations, 2012 CFR

2012-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

40 CFR 75.48 - Petition for an alternative monitoring system.

Code of Federal Regulations, 2013 CFR

2013-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

40 CFR 69.51 - Motor vehicle diesel fuel.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 16 2013-07-01 2013-07-01 false Motor vehicle diesel fuel. 69.51... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.51 Motor vehicle diesel... motor vehicle diesel fuel standards and dye provisions under 40 CFR 80.520 and associated requirements...

40 CFR 69.51 - Motor vehicle diesel fuel.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 16 2012-07-01 2012-07-01 false Motor vehicle diesel fuel. 69.51... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.51 Motor vehicle diesel... motor vehicle diesel fuel standards and dye provisions under 40 CFR 80.520 and associated requirements...

27 CFR 19.688 - Change in proprietorship.

Code of Federal Regulations, 2011 CFR

2011-04-01

... alcohol fuel plant, the following requirements apply to the outgoing proprietor and to the new, incoming... Permit for an Alcohol Fuel Producer Under 26 U.S.C. 5181; and (ii) File the required bond, if any. (b) Fiduciary responsibilities. A successor to the proprietorship of an alcohol fuel plant who is an...

40 CFR 75.48 - Petition for an alternative monitoring system.

Code of Federal Regulations, 2010 CFR

2010-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

10 CFR 503.12 - Terms and conditions; compliance plans.

Code of Federal Regulations, 2010 CFR

2010-01-01

....12 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES General Requirements for... indicating how any necessary permits and approvals required to burn an alternate fuel will be obtained; and... Act will occur; (ii) Evidence of binding contracts for fuel, or for facilities for the production of...

14 CFR 91.167 - Fuel requirements for flight in IFR conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Fuel requirements for flight in IFR conditions. 91.167 Section 91.167 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... operate a civil aircraft in IFR conditions unless it carries enough fuel (considering weather reports and...

14 CFR 91.167 - Fuel requirements for flight in IFR conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Fuel requirements for flight in IFR conditions. 91.167 Section 91.167 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... operate a civil aircraft in IFR conditions unless it carries enough fuel (considering weather reports and...

14 CFR 91.167 - Fuel requirements for flight in IFR conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Fuel requirements for flight in IFR conditions. 91.167 Section 91.167 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... operate a civil aircraft in IFR conditions unless it carries enough fuel (considering weather reports and...

14 CFR 91.167 - Fuel requirements for flight in IFR conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Fuel requirements for flight in IFR conditions. 91.167 Section 91.167 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... operate a civil aircraft in IFR conditions unless it carries enough fuel (considering weather reports and...

14 CFR 91.167 - Fuel requirements for flight in IFR conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Fuel requirements for flight in IFR conditions. 91.167 Section 91.167 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... operate a civil aircraft in IFR conditions unless it carries enough fuel (considering weather reports and...

Long Duration Exposure Facility

DTIC Science & Technology

1988-06-30

Blue and Oxazine Dyes- Name Absorption -mazimu= Lasing Wavelengths un. un. (solvent) (solvent) Nile Blue A, 635 690 Perchlorate (ethanol) (ethanol...Fluence(/cm Etching 5 Al 3.5 MeV 5x10 6 N NaOH 6 o BI8 PrQtons Ixl0 50 C, 15 hr. 6 C9 (normal 3x10 (2 sided) incidence) 01 (unirradiated) 5 DIS 2.0

EFFECT OF ULTRA-VIOLET IRRADIATION OF RIBONUCLEIC ACID ON ITS CHROMATOGRAPHIC BEHAVIOUR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kubinski, H.

1963-11-01

Experiments were made to illustrate the effects of ultraviolet radiation on RNA isolated from uninfected mammalian cells as well as those from those infected with polio virus. The chromatographic recovery of irradiated RNA, as judged by ultraviolet adsorbance and radioactivity (no plaque formers were found after irradiation), was considerably lower than that of unirradiated RNA. (P.C.H.)

46 CFR 119.405 - Fuel restrictions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Fuel restrictions. 119.405 Section 119.405 Shipping... Machinery Requirements § 119.405 Fuel restrictions. The use of a fuel, other than diesel fuel, as an alternative fuel for an internal combustion engine, except gasoline when used as a fuel for outboard motors as...

46 CFR 119.405 - Fuel restrictions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Fuel restrictions. 119.405 Section 119.405 Shipping... Machinery Requirements § 119.405 Fuel restrictions. The use of a fuel, other than diesel fuel, as an alternative fuel for an internal combustion engine, except gasoline when used as a fuel for outboard motors as...

46 CFR 119.405 - Fuel restrictions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Fuel restrictions. 119.405 Section 119.405 Shipping... Machinery Requirements § 119.405 Fuel restrictions. The use of a fuel, other than diesel fuel, as an alternative fuel for an internal combustion engine, except gasoline when used as a fuel for outboard motors as...

46 CFR 119.405 - Fuel restrictions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Fuel restrictions. 119.405 Section 119.405 Shipping... Machinery Requirements § 119.405 Fuel restrictions. The use of a fuel, other than diesel fuel, as an alternative fuel for an internal combustion engine, except gasoline when used as a fuel for outboard motors as...

46 CFR 119.405 - Fuel restrictions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Fuel restrictions. 119.405 Section 119.405 Shipping... Machinery Requirements § 119.405 Fuel restrictions. The use of a fuel, other than diesel fuel, as an alternative fuel for an internal combustion engine, except gasoline when used as a fuel for outboard motors as...

A review of the studies on the wholesomeness of irradiated wheat, conducted at the national institute of nutrition, India

NASA Astrophysics Data System (ADS)

Vijayalaxmi; Srikantia, S. G.

The wholesomeness of irradiated wheat was investigated in a series of experiments involving several species of animals and a small number of children, at the National Institute of Nutrition in India. Our observations indicated some effects following the feeding of freshly irradiated wheat while no such changes were found in the groups fed either unirradiated or stored irradiated wheat. Also, there were no significant differences between the groups fed unirradiated and stored irradiated wheat. Based on these results, a recommendation had been made to the government that when subjected to irradiation, wheat should be stored for at least 3 months before considering it as safe for human consumption. Similar experiments conducted in an establishment of the Department of Atomic Energy in India indicated no undesirable effects, unlike those found in our studies, and this had led to the development of a serious controversy. In this paper, we have not only reviewed our studies in the light of subsequent research independently carried out in other laboratories but also have tried to answer some of the criticisms made against our studies, so that some of the misunderstandings of our work are seen in proper perspective.

Giant-Planet Chemistry: Ammonium Hydrosulfide (NH4SH), Its IR Spectra and Thermal and Radiolytic Stabilities

NASA Technical Reports Server (NTRS)

Loeffler, Mark J.; Hudson, Reggie L.; Chanover, Nancy J.; Simon, Amy A.

2015-01-01

Here we present our recent studies of proton-irradiated and unirradiated ammonium hydrosulfide, NH4SH, a compound predicted to be an important tropospheric cloud component of Jupiter and other giant planets. We irradiated both crystalline and amorphous NH4SH at 10-160 K and used IR spectroscopy to observe and identify reaction products in the ice, specifically NH3 and long-chained sulfur-containing ions. Crystalline NH4SH was amorphized during irradiation at all temperatures studied with the rate being the fastest at the lowest temperatures. Irradiation of amorphous NH4SH at approximately 10-75 K showed that 60-80% of the NH4 + remained when equilibrium was reached, and that NH4SH destruction rates were relatively constant within this temperature range. Irradiations at higher temperatures produced different dose dependence and were accompanied by pressure outbursts that, in some cases, fractured the ice. The thermal stability of irradiated NH4SH was found to be greater than that of unirradiated NH4SH, suggesting that an irradiated giant-planet cloud precipitate can exist at temperatures and altitudes not previously considered.

Investigation of irradiated 1H-Benzo[b]pyrrole by ESR, thermal methods and learning algorithm

NASA Astrophysics Data System (ADS)

Algul, Gulay; Ceylan, Yusuf; Usta, Keziban; Yumurtaci Aydogmus, Hacer; Usta, Ayhan; Asik, Biray

2016-05-01

1H-Benzo[b]pyrrole samples were irradiated in the air with gamma source at 0.969 kGy per hour at room temperature for 24, 48 and 72 h. After irradiation, electron spin resonance, thermogravimetry analysis (TGA) and differential thermal analysis (DTA) measurements were immediately carried out on the irradiated and unirradiated samples. The ESR measurements were performed between 320 and 400 K. ESR spectra were recorded from the samples irradiated for 48 and 72 h. The obtained spectra were observed to be dependent on temperature. Two radical-type centres were detected on the sample. Detected radiation-induced radicals were attributed to R-+•NH and R=•CC2H2. The g-values and hyperfine constants were calculated by means of the experimental spectra. It was also determined from TGA spectrum that both the unirradiated and irradiated samples were decomposed at one step with the rising temperature. Moreover, a theoretical study was presented. Success of the machine learning methods was tested. It was found that bagging techniques, which are widely used in the machine learning literature, could optimise prediction accuracy noticeably.

ESR and TL studies of irradiated Anatolian laurel leaf (Laurus nobilis L.)

NASA Astrophysics Data System (ADS)

Tepe Çam, Semra; Aydaş, Canan; Engin, Birol; Rabia Yüce, Ülkü; Aydın, Talat; Polat, Mustafa

2012-06-01

Laurel leaf (Laurus nobilis L.) samples that originated from Turkey were analyzed by electron spin resonance (ESR) and thermoluminescence (TL) techniques before and after γ-irradiation. Unirradiated (control) laurel leaf samples exhibit a weak ESR singlet centered at g=2.0020. Besides this central signal were two weak satellite signals situated about 3 mT left and right to it in radiation-induced spectra. The dose-response curve of the radiation-induced ESR signal at g=2.0187 (the left satellite signal) was found to be described well by a power function. Variation of the left satellite ESR signal intensity of irradiated samples at room temperature with time in a long term showed that cellulosic free radicals responsible for the ESR spectrum of laurel leaves were not stable but detectable even after 100 days. Annealing studies at four different temperatures were used to determine the kinetic behavior and activation energy of the radiation-induced cellulosic free radicals responsible from the left satellite signal (g=2.0187) in laurel leaves. TL measurements of the polymineral dust isolated from the laurel leaf samples allowed distinguishing between irradiated and unirradiated samples.

Effect of Gamma Radiation on the Ripening of Bartlett Pears 1

PubMed Central

Maxie, E. C.; Sommer, N. F.; Muller, Carlos J.; Rae, Henry L.

1966-01-01

Gamma radiation at doses of 300 Krad or more inhibits the ripening of Bartlett pears (Pyrus communis L.). Immediately after irradiation there is a transitory burst of C2H4, which subsequently declines in fruits subjected to inhibitory doses. Ethylene production associated with ripening begins at the same time in unirradiated fruits and those subjected to noninhibitory doses, but the latter produces much more C2H4 at the climacteric peak. Fruits subjected to inhibitory doses produce low levels of C2H4 unless subjected to exogenously applied C2H4, whereupon they produce enough of the gas to induce ripening in unirradiated fruits. Pears subjected to 300 and 400 Krad of gamma rays did not ripen even when held in a flowing atmosphere containing 1000 ppm of C2H4 for 8 days at 20°. It is concluded that the action of gamma rays on Bartlett pears involves both an inhibition of C2H4 production and a decreased sensitivity of the fruit to the ripening action of the gas. Ripening of Bartlett pears is inhibited by gamma radiation only when applied to preclimacteric fruit. PMID:16656274

An early glimpse at long-term subsonic commercial turbofan technology requirements. [fuel conservation

NASA Technical Reports Server (NTRS)

Gray, D. E.; Dugan, J. F.

1975-01-01

This paper reports on the exploratory investigation and initial findings of the study of future turbofan concepts to conserve fuel. To date, these studies have indicated a potential reduction in cruise thrust specific fuel consumption in 1990 turbofans of approximately 15% relative to present day new engines through advances in internal aerodynamics, structure-mechanics, and materials. Advanced materials also offer the potential for fuel savings through engine weight reduction. Further studies are required to balance fuel consumption reduction with sound airlines operational economics.

Capital requirements and fuel-cycle energy and emissions impacts of potential PNGV fuels.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, L.; Mintz, M.; Singh, M.

1999-03-11

Our study reveals that supplying gasoline-equivalent demand for the low-market-share scenario requires a capital investment of less thanmore » $$40 billion for all fuels except H{sub 2}, which will require a total cumulative investment of $$150 billion. By contrast, cumulative capital investments under the high-market-share scenario are $50 billion for LNG, $90 billion for ethanol, $100 billion for methanol, $160 billion for CNG and DME, and $560 billion for H{sub 2}. Although these substantial capital requirements are spread over many years, their magnitude could pose a challenge to the widespread introduction of 3X vehicles. Fossil fuel use by US light-duty vehicles declines significantly with introduction of 3X vehicles because of fuel-efficiency improvements for 3X vehicles and because of fuel substitution (which applies to the nonpetroleum-fueled alternatives). Petroleum use for light-duty vehicles in 2030 is reduced by as much as 45% relative to the reference scenario. GHG emissions follow a similar pattern. Total GHG emissions decline by 25-30% with most of the propulsion system/fuel alternatives. For those using renewable fuels (i.e., ethanol and H{sub 2} from solar energy), GHG emissions drop by 33% (H{sub 2}) and 45% (ethanol). Among urban air pollutants, urban NOX emissions decline slightly for 3X vehicles using CIDI and SIDI engines and drop substantially for fuel-cell vehicles. Urban CO emissions decline for CIDI and FCV alternatives, while VOC emissions drop significantly for all alternatives except RFG-, methanol-, and ethanol-fueled SIDI engines. With the exception of CIDI engines fueled by RFD, FT50, or B20 (which increase urban PM{sub 10} emissions by over 30%), all propulsion system/fuel alternatives reduce urban PM{sub 10} emissions. Reductions are approximately 15-20% for fuel cells and for methanol-, ethanol-, CNG-, or LPG-fueled SIDI engines. Table 3 qualitatively summarizes impacts of the 13 alternatives on capital requirements and on energy use and emissions relative to the reference scenario. The table clearly shows the trade-off between costs and benefits. For example, while H{sub 2} FCVs have the greatest incremental capital needs, they offer the largest energy and emissions benefits. On the basis of the cost and benefit changes shown, methanol and gasoline FCVs appear to have particularly promising benefits-to-costs ratios.« less

40 CFR 80.219 - Designation and downstream requirements for GPA gasoline.

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for GPA gasoline. 80.219 Section 80.219 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase-in Program § 80.219 Designation and downstream requirements for GPA gasoline. The requirements and...

40 CFR 80.219 - Designation and downstream requirements for GPA gasoline.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for GPA gasoline. 80.219 Section 80.219 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase-in Program § 80.219 Designation and downstream requirements for GPA gasoline. The requirements and...

40 CFR 80.219 - Designation and downstream requirements for GPA gasoline.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for GPA gasoline. 80.219 Section 80.219 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase-in Program § 80.219 Designation and downstream requirements for GPA gasoline. The requirements and...

40 CFR 80.219 - Designation and downstream requirements for GPA gasoline.

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for GPA gasoline. 80.219 Section 80.219 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase-in Program § 80.219 Designation and downstream requirements for GPA gasoline. The requirements and...

40 CFR 80.219 - Designation and downstream requirements for GPA gasoline.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for GPA gasoline. 80.219 Section 80.219 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase-in Program § 80.219 Designation and downstream requirements for GPA gasoline. The requirements and...

Determination of He and D permeability of neutron-irradiated SiC tubes to examine the potential for release due to micro-cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katoh, Yutai; Hu, Xunxiang; Koyanagi, Takaaki

Driven by the need to enlarge the safety margins of light water reactors in both design-basis and beyond-design-basis accident scenarios, the research and development of accident-tolerant fuel (ATF) has become an importance topic in the nuclear engineering and materials community. Continuous SiC fiber-reinforced SiC matrix ceramic composites are under consideration as a replacement for traditional zirconium alloy cladding owing to their high-temperature stability, chemical inertness, and exceptional irradiation resistance. Among the key technical feasibility issues, potential failure of the fission product containment due to probabilistic penetrating cracking has been identified as one of the two most critical feasibility issues, togethermore » with the radiolysisassisted hydrothermal corrosion of SiC. The experimental capability to evaluate the hermeticity of SiC-based claddings is an urgent need. In this report, we present the development of a comprehensive permeation testing station established in the Low Activation Materials Development and Analysis laboratory at Oak Ridge National Laboratory. Preliminary results for the hermeticity evaluation of un-irradiated monolithic SiC tubes, uncoated and coated SiC/SiC composite tubes, and neutron-irradiated monolithic SiC tubes at room temperature are exhibited. The results indicate that this new permeation testing station is capable of evaluating the hermeticity of SiC-based tubes by determining the helium and deuterium permeation flux as a function of gas pressure at a high resolution of 8.07 x 10 -12 atm-cc/s for helium and 2.83 x 10 -12 atm-cc/s for deuterium, respectively. The detection limit of this system is sufficient to evaluate the maximum allowable helium leakage rate of lab-scale tubular samples, which is linearly extrapolated from the evaluation standard used for a commercial as-manufactured light water reactor fuel rod at room temperature. The un-irradiated monolithic SiC tube is hermetic, as is manifested by the un-detectable deuterium permeation flux at various feeding gas pressures. A large helium leakage rate was detected for the uncoated SiC/SiC composite tube exposed to atmosphere, indicating it is inherently not hermetic. The hermeticity of coated SiC/SiC composite tubes is strongly dependent on the coating materials and the preparation of the substrate SiC/SiC composite samples. To simulate the practical application environment, monolithic CVD SiC tubes were exposed to neutron irradiation at the High Flux Isotope Reactor under high heat flux from the internal surface to the external surface. Although finite element analysis and resonant ultrasound spectroscopy measurement indicated that the combined neutron irradiation and high heat flux gave rise to a high probability of cracking within the sample, the hermeticity evaluation of the tested sample still exhibited gas tightness, emphasizing that SiC cracking is inherently a statistical phenomenon. The developed permeation testing station is capable of measuring the gas permeation flux in the range of interest with full confidence based on the presented results. It is considered a critical pre- /post-irradiation examination technique to characterize SiC-based cladding materials in asreceived and irradiated states to aid the research and development of ATF.« less

40 CFR 80.524 - What sulfur content standard applies to motor vehicle diesel fuel downstream of the refinery or...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to motor vehicle diesel fuel downstream of the refinery or importer? 80.524 Section 80.524 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.524 What sulfur content standard...

40 CFR 80.524 - What sulfur content standard applies to motor vehicle diesel fuel downstream of the refinery or...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to motor vehicle diesel fuel downstream of the refinery or importer? 80.524 Section 80.524 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.524 What sulfur content standard...

Controls Over Ministry of Interior Fuel Contracts Could be Improved

DTIC Science & Technology

2016-01-20

Fiscal Year 1395 Commitment Letter improved reporting requirements designed to specify adequate documentation of the Afghan Ministry of Interior fuel...1395 Commitment Letter improved reporting requirements designed to specify adequate documentation of the Afghan Ministry of Interior fuel consumption...of Defense F r a u d , W a s t e & A b u s e FOR OFFICIAL USE ONLY FOR OFFICIAL USE ONLY Results in Brief Controls Over Ministry of Interior Fuel

Regulatory cross-cutting topics for fuel cycle facilities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denman, Matthew R.; Brown, Jason; Goldmann, Andrew Scott

This report overviews crosscutting regulatory topics for nuclear fuel cycle facilities for use in the Fuel Cycle Research & Development Nuclear Fuel Cycle Evaluation and Screening study. In particular, the regulatory infrastructure and analysis capability is assessed for the following topical areas: Fire Regulations (i.e., how applicable are current Nuclear Regulatory Commission (NRC) and/or International Atomic Energy Agency (IAEA) fire regulations to advance fuel cycle facilities) Consequence Assessment (i.e., how applicable are current radionuclide transportation tools to support risk-informed regulations and Level 2 and/or 3 PRA) While not addressed in detail, the following regulatory topic is also discussed: Integrated Security,more » Safeguard and Safety Requirement (i.e., how applicable are current Nuclear Regulatory Commission (NRC) regulations to future fuel cycle facilities which will likely be required to balance the sometimes conflicting Material Accountability, Security, and Safety requirements.)« less

Major design issues of molten carbonate fuel cell power generation unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, T.P.

1996-04-01

In addition to the stack, a fuel cell power generation unit requires fuel desulfurization and reforming, fuel and oxidant preheating, process heat removal, waste heat recovery, steam generation, oxidant supply, power conditioning, water supply and treatment, purge gas supply, instrument air supply, and system control. These support facilities add considerable cost and system complexity. Bechtel, as a system integrator of M-C Power`s molten carbonate fuel cell development team, has spent substantial effort to simplify and minimize these supporting facilities to meet cost and reliability goals for commercialization. Similiar to other fuels cells, MCFC faces design challenge of how to complymore » with codes and standards, achieve high efficiency and part load performance, and meanwhile minimize utility requirements, weight, plot area, and cost. However, MCFC has several unique design issues due to its high operating temperature, use of molten electrolyte, and the requirement of CO2 recycle.« less

14 CFR 27.955 - Fuel flow.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.955 Fuel flow. (a) General. The fuel system for each engine must be shown to provide the engine with at least 100 percent of the fuel required... to rotorcraft flight attitudes. (4) The critical fuel pump (for pump-fed systems) is installed to...

14 CFR 27.955 - Fuel flow.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.955 Fuel flow. (a) General. The fuel system for each engine must be shown to provide the engine with at least 100 percent of the fuel required... to rotorcraft flight attitudes. (4) The critical fuel pump (for pump-fed systems) is installed to...

14 CFR 29.955 - Fuel flow.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.955 Fuel flow. (a) General. The fuel system for each engine must provide the engine with at least 100 percent of the fuel required under all... flow transmitter, if installed, and the critical fuel pump (for pump-fed systems) must be installed to...

14 CFR 27.955 - Fuel flow.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.955 Fuel flow. (a) General. The fuel system for each engine must be shown to provide the engine with at least 100 percent of the fuel required... to rotorcraft flight attitudes. (4) The critical fuel pump (for pump-fed systems) is installed to...

14 CFR 27.955 - Fuel flow.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.955 Fuel flow. (a) General. The fuel system for each engine must be shown to provide the engine with at least 100 percent of the fuel required... to rotorcraft flight attitudes. (4) The critical fuel pump (for pump-fed systems) is installed to...

14 CFR 29.955 - Fuel flow.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.955 Fuel flow. (a) General. The fuel system for each engine must provide the engine with at least 100 percent of the fuel required under all... flow transmitter, if installed, and the critical fuel pump (for pump-fed systems) must be installed to...

14 CFR 29.955 - Fuel flow.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.955 Fuel flow. (a) General. The fuel system for each engine must provide the engine with at least 100 percent of the fuel required under all... flow transmitter, if installed, and the critical fuel pump (for pump-fed systems) must be installed to...

14 CFR 29.955 - Fuel flow.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.955 Fuel flow. (a) General. The fuel system for each engine must provide the engine with at least 100 percent of the fuel required under all... flow transmitter, if installed, and the critical fuel pump (for pump-fed systems) must be installed to...

14 CFR 27.955 - Fuel flow.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.955 Fuel flow. (a) General. The fuel system for each engine must be shown to provide the engine with at least 100 percent of the fuel required... to rotorcraft flight attitudes. (4) The critical fuel pump (for pump-fed systems) is installed to...

14 CFR 29.955 - Fuel flow.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.955 Fuel flow. (a) General. The fuel system for each engine must provide the engine with at least 100 percent of the fuel required under all... flow transmitter, if installed, and the critical fuel pump (for pump-fed systems) must be installed to...

77 FR 19074 - Airworthiness Directives; DASSAULT AVIATION Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-30

... reports of fuel leakage from a defective fuel high-level sensor located in the wing front spar. This AD requires inspecting to determine fuel quantity sensors part numbers and replacing of certain fuel quantity sensors with new fuel quantity sensors. We are issuing this AD to prevent internal fuel leakage with...

40 CFR 79.30 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.30 Scope. Fuels and additives designated and dates prescribed by the Administrator for the registration of such fuels and additives... requirements under §§ 79.11(f) and 79.21(e) are set forth for each designated fuel or additive. Additional...

40 CFR 79.30 - Scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.30 Scope. Fuels and additives designated and dates prescribed by the Administrator for the registration of such fuels and additives... requirements under §§ 79.11(f) and 79.21(e) are set forth for each designated fuel or additive. Additional...

40 CFR 79.30 - Scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.30 Scope. Fuels and additives designated and dates prescribed by the Administrator for the registration of such fuels and additives... requirements under §§ 79.11(f) and 79.21(e) are set forth for each designated fuel or additive. Additional...

40 CFR 79.30 - Scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.30 Scope. Fuels and additives designated and dates prescribed by the Administrator for the registration of such fuels and additives... requirements under §§ 79.11(f) and 79.21(e) are set forth for each designated fuel or additive. Additional...

40 CFR 79.30 - Scope.

Code of Federal Regulations, 2014 CFR

2014-07-01

... FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.30 Scope. Fuels and additives designated and dates prescribed by the Administrator for the registration of such fuels and additives... requirements under §§ 79.11(f) and 79.21(e) are set forth for each designated fuel or additive. Additional...

46 CFR 182.405 - Fuel restrictions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Fuel restrictions. 182.405 Section 182.405 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.405 Fuel restrictions. The use of alternative fuels, other than diesel fuel or gasoline, as fuel for an internal combustion engine will be reviewed on...

46 CFR 182.405 - Fuel restrictions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Fuel restrictions. 182.405 Section 182.405 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.405 Fuel restrictions. The use of alternative fuels, other than diesel fuel or gasoline, as fuel for an internal combustion engine will be reviewed on...

40 CFR 90.417 - Fuel flow measurement specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Fuel flow measurement specifications... Gaseous Exhaust Test Procedures § 90.417 Fuel flow measurement specifications. (a) Fuel flow measurement is required only for raw testing. Fuel flow is allowed for dilute testing. (b) The fuel flow...

49 CFR 238.223 - Locomotive fuel tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Locomotive fuel tanks. 238.223 Section 238.223... Equipment § 238.223 Locomotive fuel tanks. Locomotive fuel tanks shall comply with either the following or....21: (a) External fuel tanks. External locomotive fuel tanks shall comply with the requirements...

46 CFR 182.405 - Fuel restrictions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Fuel restrictions. 182.405 Section 182.405 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.405 Fuel restrictions. The use of alternative fuels, other than diesel fuel or gasoline, as fuel for an internal combustion engine will be reviewed on...

46 CFR 182.405 - Fuel restrictions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Fuel restrictions. 182.405 Section 182.405 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.405 Fuel restrictions. The use of alternative fuels, other than diesel fuel or gasoline, as fuel for an internal combustion engine will be reviewed on...

46 CFR 182.405 - Fuel restrictions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Fuel restrictions. 182.405 Section 182.405 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.405 Fuel restrictions. The use of alternative fuels, other than diesel fuel or gasoline, as fuel for an internal combustion engine will be reviewed on...

49 CFR 238.223 - Locomotive fuel tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Locomotive fuel tanks. 238.223 Section 238.223... Equipment § 238.223 Locomotive fuel tanks. Locomotive fuel tanks shall comply with either the following or....21: (a) External fuel tanks. External locomotive fuel tanks shall comply with the requirements...

40 CFR 86.1506 - Equipment required and specifications; overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Heavy-Duty Engines, New Otto-Cycle Light-Duty Trucks, and New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle...

40 CFR 86.1530 - Test sequence; general requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Heavy-Duty Engines, New Otto-Cycle Light-Duty Trucks, and New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle...

Planar solid oxide fuel cell with staged indirect-internal air and fuel preheating and reformation

DOEpatents

Geisbrecht, Rodney A; Williams, Mark C

2003-10-21

A solid oxide fuel cell arrangement and method of use that provides internal preheating of both fuel and air in order to maintain the optimum operating temperature for the production of energy. The internal preheat passes are created by the addition of two plates, one on either side of the bipolar plate, such that these plates create additional passes through the fuel cell. This internal preheat fuel cell configuration and method reduce the requirements for external heat exchanger units and air compressors. Air or fuel may be added to the fuel cell as required to maintain the optimum operating temperature through a cathode control valve or an anode control valve, respectively. A control loop comprises a temperature sensing means within the preheat air and fuel passes, a means to compare the measured temperature to a set point temperature and a determination based on the comparison as to whether the control valves should allow additional air or fuel into the preheat or bypass manifolds of the fuel cell.

Alternative Fuels Data Center: Emerging Fuels

Science.gov Websites

quantities. More research is needed to characterize the impacts of these fuels, such as necessary vehicle modifications, required fueling infrastructure, human health impacts, greenhouse gas emissions, and tailpipe

10 CFR 73.72 - Requirement for advance notice of shipment of formula quantities of strategic special nuclear...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., or irradiated reactor fuel. 73.72 Section 73.72 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED... strategic significance, or irradiated reactor fuel. (a) A licensee, other than one specified in paragraph (b... strategic significance, or irradiated reactor fuel required to be protected in accordance with § 73.37...

10 CFR 73.72 - Requirement for advance notice of shipment of formula quantities of strategic special nuclear...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., or irradiated reactor fuel. 73.72 Section 73.72 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED... strategic significance, or irradiated reactor fuel. (a) A licensee, other than one specified in paragraph (b... strategic significance, or irradiated reactor fuel required to be protected in accordance with § 73.37...

40 CFR 63.7506 - Do any boilers or process heaters have limited requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... the large liquid fuel subcategory or the limited use liquid fuel subcategory that burn only fossil... Notification of Compliance Status report required in § 63.7545(e) that indicates you burn only liquid fossil... you burn only liquid fossil fuels other than residual oils, either alone or in combination with...

40 CFR 63.7506 - Do any boilers or process heaters have limited requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... the large liquid fuel subcategory or the limited use liquid fuel subcategory that burn only fossil... Notification of Compliance Status report required in § 63.7545(e) that indicates you burn only liquid fossil... you burn only liquid fossil fuels other than residual oils, either alone or in combination with...

40 CFR 63.7506 - Do any boilers or process heaters have limited requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the large liquid fuel subcategory or the limited use liquid fuel subcategory that burn only fossil... Notification of Compliance Status report required in § 63.7545(e) that indicates you burn only liquid fossil... you burn only liquid fossil fuels other than residual oils, either alone or in combination with...

40 CFR 59.623 - What must I include in my application?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) List the specifications of the test fuel to show that it falls within the required ranges specified in... application (including the test procedures, test parameters, and test fuels) to show you meet the requirements... PRODUCTS Control of Evaporative Emissions From New and In-Use Portable Fuel Containers Certifying Emission...

40 CFR 59.623 - What must I include in my application?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) List the specifications of the test fuel to show that it falls within the required ranges specified in... application (including the test procedures, test parameters, and test fuels) to show you meet the requirements... PRODUCTS Control of Evaporative Emissions From New and In-Use Portable Fuel Containers Certifying Emission...

40 CFR 80.163 - Detergent certification options.

Code of Federal Regulations, 2013 CFR

2013-07-01

... rate shown to be needed in the designated test fuel in order to meet the deposit control performance... test requirements and standards specified in § 80.165 using test fuels that conform to the requirements... paragraph (a)(1) of this section, except that, pursuant to § 80.164(a)(2)(ii), the certification test fuel...

40 CFR 80.163 - Detergent certification options.

Code of Federal Regulations, 2012 CFR

2012-07-01

... rate shown to be needed in the designated test fuel in order to meet the deposit control performance... test requirements and standards specified in § 80.165 using test fuels that conform to the requirements... paragraph (a)(1) of this section, except that, pursuant to § 80.164(a)(2)(ii), the certification test fuel...

40 CFR 80.163 - Detergent certification options.

Code of Federal Regulations, 2014 CFR

2014-07-01

... rate shown to be needed in the designated test fuel in order to meet the deposit control performance... test requirements and standards specified in § 80.165 using test fuels that conform to the requirements... paragraph (a)(1) of this section, except that, pursuant to § 80.164(a)(2)(ii), the certification test fuel...

40 CFR 59.623 - What must I include in my application?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) List the specifications of the test fuel to show that it falls within the required ranges specified in... application (including the test procedures, test parameters, and test fuels) to show you meet the requirements... PRODUCTS Control of Evaporative Emissions From New and In-Use Portable Fuel Containers Certifying Emission...

40 CFR 59.623 - What must I include in my application?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) List the specifications of the test fuel to show that it falls within the required ranges specified in... application (including the test procedures, test parameters, and test fuels) to show you meet the requirements... PRODUCTS Control of Evaporative Emissions From New and In-Use Portable Fuel Containers Certifying Emission...

40 CFR 80.163 - Detergent certification options.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rate shown to be needed in the designated test fuel in order to meet the deposit control performance... test requirements and standards specified in § 80.165 using test fuels that conform to the requirements... paragraph (a)(1) of this section, except that, pursuant to § 80.164(a)(2)(ii), the certification test fuel...

40 CFR 59.623 - What must I include in my application?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) List the specifications of the test fuel to show that it falls within the required ranges specified in... application (including the test procedures, test parameters, and test fuels) to show you meet the requirements... PRODUCTS Control of Evaporative Emissions From New and In-Use Portable Fuel Containers Certifying Emission...

46 CFR 119.470 - Ventilation of spaces containing diesel fuel tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Ventilation of spaces containing diesel fuel tanks. 119... MACHINERY INSTALLATION Specific Machinery Requirements § 119.470 Ventilation of spaces containing diesel... containing a diesel fuel tank and no machinery must meet one of the following requirements: (1) A space of 14...

46 CFR 119.470 - Ventilation of spaces containing diesel fuel tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Ventilation of spaces containing diesel fuel tanks. 119... MACHINERY INSTALLATION Specific Machinery Requirements § 119.470 Ventilation of spaces containing diesel... containing a diesel fuel tank and no machinery must meet one of the following requirements: (1) A space of 14...

27 CFR 19.716 - Maintenance and retention of records.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Recordkeeping § 19.716 Maintenance and retention of records. (a) A proprietor of an alcohol fuel plant may keep the records required by this subpart at the alcohol fuel plant where operations or transactions occur... required records at any location other than the alcohol fuel plant where operations or transactions occur...

40 CFR 88.205-94 - California Pilot Test Program Credits Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Program to meet the clean-fuel vehicle sales requirements through the use of credits. Participation in... be generated by any of the following means: (i) Sale of qualifying clean-fuel vehicles earlier than... requirements of paragraph (g) of this section. (ii) Sale of a greater number of qualifying clean-fuel vehicles...

40 CFR 1066.145 - Test fuel, engine fluids, analytical gases, and other calibration standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements of 40 CFR 1065.750. (e) Mass standards. Use mass standards that meet the requirements of 40 CFR... gases, and other calibration standards. 1066.145 Section 1066.145 Protection of Environment..., analytical gases, and other calibration standards. (a) Test fuel. Use test fuel as specified in the standard...

Regulation of Fuel and Fuel Additives: Refiner and Importer Quality Assurance Requirements for Downstream Oxygenate Blending and Requirements for Disposition of Pipeline Interfaces Additional Resources

EPA Pesticide Factsheets

EPA has published a Direct Final Rule that addresses requirements for parties that handle pipeline interface as well as addresses downstream quality assurance requirements for refiners (EPA publication # EPA-420-F-06-039).

46 CFR 111.105-39 - Additional requirements for vessels carrying vehicles with fuel in their tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Additional requirements for vessels carrying vehicles... SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-39 Additional requirements for vessels carrying vehicles with fuel in their tanks. Each vessel...

46 CFR 111.105-39 - Additional requirements for vessels carrying vehicles with fuel in their tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Additional requirements for vessels carrying vehicles... SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-39 Additional requirements for vessels carrying vehicles with fuel in their tanks. Each vessel...

76 FR 2243 - List of Approved Spent Fuel Storage Casks: NUHOMS ® HD System Revision 1

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-13

... the requirements of reconstituted fuel assemblies; add requirements to qualify metal matrix composite... requirements to qualify metal matrix composite neutron absorbers with integral aluminum cladding; clarify the... requirements to qualify metal matrix composite neutron absorbers with integral aluminum cladding; clarify the...

The TMI Regenerative Solid Oxide Fuel Cell

NASA Technical Reports Server (NTRS)

Cable, Thomas L.; Ruhl, Robert C.; Petrik, Michael

1996-01-01

Energy storage and production in space requires rugged, reliable hardware which minimizes weight, volume, and maintenance while maximizing power output and usable energy storage. Systems generally consist of photovoltaic solar arrays which operate (during sunlight cycles) to provide system power and regenerate fuel (hydrogen) via water electrolysis and (during dark cycles) fuel cells convert hydrogen into electricity. Common configurations use two separate systems (fuel cell and electrolyzer) in conjunction with photovoltaic cells. Reliability, power to weight and power to volume ratios could be greatly improved if both power production (fuel cells) and power storage (electrolysis) functions can be integrated into a single unit. The solid oxide fuel cell (SOFC) based design integrates fuel cell and electrolyzer functions and potentially simplifies system requirements. The integrated fuel cell/electrolyzer design also utilizes innovative gas storage concepts and operates like a rechargeable 'hydrogen-oxygen battery'. Preliminary research has been completed on improved H2/H20 electrode (SOFC anode/electrolyzer cathode) materials for regenerative fuel cells. Tests have shown improved cell performance in both fuel and electrolysis modes in reversible fuel cell tests. Regenerative fuel cell efficiencies, ratio of power out (fuel cell mode) to power in (electrolyzer mode), improved from 50 percent using conventional electrode materials to over 80 percent. The new materials will allow a single SOFC system to operate as both the electolyzer and fuel cell. Preliminary system designs have also been developed to show the technical feasibility of using the design for space applications requiring high energy storage efficiencies and high specific energy. Small space systems also have potential for dual-use, terrestrial applications.

77 FR 5418 - Airworthiness Directives; Sikorsky Aircraft Corporation Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-03

... aft fuel system 40 micron fuel filter element with a 10 micron fuel filter element. This proposed AD... fuel filter element, part number (P/N) 52-0505-2 or 52-01064-1. This proposed AD would require replacing each forward and aft fuel system 40 micron fuel filter element with a 10 micron fuel filter...

The in-plant evaluation of a uranium NDA system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sprinkle, J.K. Jr.; Baxman, H.R.; Langner, D.G.

1979-12-31

The Los Alamos Scientific Laboratory has an unirradiated enriched uranium reprocessing facility. Various types of solutions are generated in this facility, including distillates and raffinates containing ppm of uranium and concentrated solutions with up to 400 grams U/t. In addition to uranyl nitrate and HNO{sub 3}, the solutions may also contain zirconium, niobium, fluoride, and small amounts of many metals. A uranium solution assay system (USAS) has been installed to allow accurate and more timely process control, accountability, and criticality data to be obtained. The USAS assays are made by a variety of techniques that depend upon state-of-the-art high-resolution Ge(Li)more » gamma-ray spectroscopy integrated with an interactive, user-oriented computer software package. Tight control of the system`s performance is maintained by constantly monitoring the USAS status. Daily measurement control sequences are required, and the user is forced by the software to perform these sequences. Routine assays require 400 or 1000 seconds for a precision of 0.5% over the concentration range of 5--400 g/t. A comparison of the USAS precision and accuracy with that obtained by traditional destructive analytical chemistry techniques (colorimetric and volumetric) is presented.« less

The in-plant evaluation of a uranium NDA system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sprinkle, J.K. Jr.; Baxman, H.R.; Langner, D.G.

1979-01-01

The Los Alamos Scientific Laboratory has an unirradiated enriched uranium reprocessing facility. Various types of solutions are generated in this facility, including distillates and raffinates containing ppm of uranium and concentrated solutions with up to 400 grams U/t. In addition to uranyl nitrate and HNO{sub 3}, the solutions may also contain zirconium, niobium, fluoride, and small amounts of many metals. A uranium solution assay system (USAS) has been installed to allow accurate and more timely process control, accountability, and criticality data to be obtained. The USAS assays are made by a variety of techniques that depend upon state-of-the-art high-resolution Ge(Li)more » gamma-ray spectroscopy integrated with an interactive, user-oriented computer software package. Tight control of the system's performance is maintained by constantly monitoring the USAS status. Daily measurement control sequences are required, and the user is forced by the software to perform these sequences. Routine assays require 400 or 1000 seconds for a precision of 0.5% over the concentration range of 5--400 g/t. A comparison of the USAS precision and accuracy with that obtained by traditional destructive analytical chemistry techniques (colorimetric and volumetric) is presented.« less

40 CFR 80.510 - What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel?

Code of Federal Regulations, 2013 CFR

2013-07-01

... for in paragraph (i) of this section, any diesel fuel, other than jet fuel or kerosene that is... this section, any diesel fuel, other than jet fuel or kerosene that is downstream of a truck loading... diesel fuel, other than jet fuel or kerosene that is downstream of a truck loading terminal, that...

40 CFR 80.510 - What are the standards and marker requirements for NRLM diesel fuel and ECA marine fuel?

Code of Federal Regulations, 2014 CFR

2014-07-01

... for in paragraph (i) of this section, any diesel fuel, other than jet fuel or kerosene that is... this section, any diesel fuel, other than jet fuel or kerosene that is downstream of a truck loading... diesel fuel, other than jet fuel or kerosene that is downstream of a truck loading terminal, that...

Self-regulating control of parasitic loads in a fuel cell power system

NASA Technical Reports Server (NTRS)

Vasquez, Arturo (Inventor)

2011-01-01

A fuel cell power system comprises an internal or self-regulating control of a system or device requiring a parasitic load. The internal or self-regulating control utilizes certain components and an interconnection scheme to produce a desirable, variable voltage potential (i.e., power) to a system or device requiring parasitic load in response to varying operating conditions or requirements of an external load that is connected to a primary fuel cell stack of the system. Other embodiments comprise a method of designing such a self-regulated control scheme and a method of operating such a fuel cell power system.

49 CFR 525.6 - Requirements for petition.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EXEMPTIONS FROM AVERAGE FUEL ECONOMY STANDARDS § 525.6 Requirements... arguments of the petitioner supporting the exemption and alternative average fuel economy standard requested...

14 CFR 25.953 - Fuel system independence.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel system independence. 25.953 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.953 Fuel system independence. Each fuel system must meet the requirements of § 25.903(b) by— (a) Allowing the supply of fuel to each...

14 CFR 25.953 - Fuel system independence.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel system independence. 25.953 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.953 Fuel system independence. Each fuel system must meet the requirements of § 25.903(b) by— (a) Allowing the supply of fuel to each...

14 CFR 25.953 - Fuel system independence.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel system independence. 25.953 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.953 Fuel system independence. Each fuel system must meet the requirements of § 25.903(b) by— (a) Allowing the supply of fuel to each...

14 CFR 25.953 - Fuel system independence.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel system independence. 25.953 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.953 Fuel system independence. Each fuel system must meet the requirements of § 25.903(b) by— (a) Allowing the supply of fuel to each...

14 CFR 25.953 - Fuel system independence.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system independence. 25.953 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.953 Fuel system independence. Each fuel system must meet the requirements of § 25.903(b) by— (a) Allowing the supply of fuel to each...

40 CFR 80.598 - What are the designation requirements for refiners, importers, and distributors?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (MVNRLM) diesel fuel. (B) Heating oil. (C) Jet fuel. (D) Kerosene. (E) No. 4 fuel. (F) Distillate fuel for... for use as kerosene or jet fuel (i.e., commonly referred to as dual use kerosene) may be designated as MVNRLM, kerosene, or jet fuel (as applicable). (viii) Beginning June 1, 2007, any distillate fuel with a...

40 CFR 80.598 - What are the designation requirements for refiners, importers, and distributors?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (MVNRLM) diesel fuel. (B) Heating oil. (C) Jet fuel. (D) Kerosene. (E) No. 4 fuel. (F) Distillate fuel for... for use as kerosene or jet fuel (i.e., commonly referred to as dual use kerosene) may be designated as MVNRLM, kerosene, or jet fuel (as applicable). (viii) Beginning June 1, 2007, any distillate fuel with a...

26 CFR 48.4082-1T - Diesel fuel and kerosene; exemption for dyed fuel (temporary).

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Diesel fuel and kerosene; exemption for dyed... Vehicles, Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-1T Diesel fuel and kerosene... this section, diesel fuel or kerosene satisfies the dyeing requirements of this paragraph (d) only if...

40 CFR 80.598 - What are the designation requirements for refiners, importers, and distributors?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (MVNRLM) diesel fuel. (B) Heating oil. (C) Jet fuel. (D) Kerosene. (E) No. 4 fuel. (F) Distillate fuel for... for use as kerosene or jet fuel (i.e., commonly referred to as dual use kerosene) may be designated as MVNRLM, kerosene, or jet fuel (as applicable). (viii) Beginning June 1, 2007, any distillate fuel with a...

40 CFR 80.598 - What are the designation requirements for refiners, importers, and distributors?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (MVNRLM) diesel fuel. (B) Heating oil. (C) Jet fuel. (D) Kerosene. (E) No. 4 fuel. (F) Distillate fuel for... for use as kerosene or jet fuel (i.e., commonly referred to as dual use kerosene) may be designated as MVNRLM, kerosene, or jet fuel (as applicable). (viii) Beginning June 1, 2007, any distillate fuel with a...

26 CFR 48.4082-1T - Diesel fuel and kerosene; exemption for dyed fuel (temporary).

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 16 2013-04-01 2013-04-01 false Diesel fuel and kerosene; exemption for dyed... Vehicles, Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-1T Diesel fuel and kerosene... this section, diesel fuel or kerosene satisfies the dyeing requirements of this paragraph (d) only if...

40 CFR 80.598 - What are the designation requirements for refiners, importers, and distributors?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (MVNRLM) diesel fuel. (B) Heating oil. (C) Jet fuel. (D) Kerosene. (E) No. 4 fuel. (F) Distillate fuel for... for use as kerosene or jet fuel (i.e., commonly referred to as dual use kerosene) may be designated as MVNRLM, kerosene, or jet fuel (as applicable). (viii) Beginning June 1, 2007, any distillate fuel with a...

26 CFR 48.4082-1T - Diesel fuel and kerosene; exemption for dyed fuel (temporary).

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 16 2012-04-01 2012-04-01 false Diesel fuel and kerosene; exemption for dyed... Vehicles, Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-1T Diesel fuel and kerosene... this section, diesel fuel or kerosene satisfies the dyeing requirements of this paragraph (d) only if...

26 CFR 48.4082-1T - Diesel fuel and kerosene; exemption for dyed fuel (temporary).

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 16 2011-04-01 2011-04-01 false Diesel fuel and kerosene; exemption for dyed... Vehicles, Tires, Tubes, Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4082-1T Diesel fuel and kerosene... this section, diesel fuel or kerosene satisfies the dyeing requirements of this paragraph (d) only if...

14 CFR 125.179 - Fuel system independence.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Fuel system independence. 125.179 Section... Requirements § 125.179 Fuel system independence. (a) Each airplane fuel system must be arranged so that the... the fuel system incorporates features that provide equivalent safety. ...

14 CFR 125.179 - Fuel system independence.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Fuel system independence. 125.179 Section... Requirements § 125.179 Fuel system independence. (a) Each airplane fuel system must be arranged so that the... the fuel system incorporates features that provide equivalent safety. ...

14 CFR 125.179 - Fuel system independence.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Fuel system independence. 125.179 Section... Requirements § 125.179 Fuel system independence. (a) Each airplane fuel system must be arranged so that the... the fuel system incorporates features that provide equivalent safety. ...

49 CFR 229.217 - Fuel tank.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Fuel tank. 229.217 Section 229.217 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Crashworthiness Design Requirements § 229.217 Fuel tank. (a) External fuel tanks. Locomotives equipped with external fuel tanks shall, at a minimum...

49 CFR 229.217 - Fuel tank.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Fuel tank. 229.217 Section 229.217 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Crashworthiness Design Requirements § 229.217 Fuel tank. (a) External fuel tanks. Locomotives equipped with external fuel tanks shall, at a minimum...

49 CFR 229.217 - Fuel tank.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Fuel tank. 229.217 Section 229.217 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Crashworthiness Design Requirements § 229.217 Fuel tank. (a) External fuel tanks. Locomotives equipped with external fuel tanks shall, at a minimum...

49 CFR 229.217 - Fuel tank.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Fuel tank. 229.217 Section 229.217 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Crashworthiness Design Requirements § 229.217 Fuel tank. (a) External fuel tanks. Locomotives equipped with external fuel tanks shall, at a minimum...

Coal conversion processes and analysis methodologies for synthetic fuels production. [technology assessment and economic analysis of reactor design for coal gasification

NASA Technical Reports Server (NTRS)

1979-01-01

Information to identify viable coal gasification and utilization technologies is presented. Analysis capabilities required to support design and implementation of coal based synthetic fuels complexes are identified. The potential market in the Southeast United States for coal based synthetic fuels is investigated. A requirements analysis to identify the types of modeling and analysis capabilities required to conduct and monitor coal gasification project designs is discussed. Models and methodologies to satisfy these requirements are identified and evaluated, and recommendations are developed. Requirements for development of technology and data needed to improve gasification feasibility and economies are examined.