An empirical examination of the impacts of decentralized nursing unit design.

PubMed

Pati, Debajyoti; Harvey, Thomas E; Redden, Pamela; Summers, Barbara; Pati, Sipra

2015-01-01

The objective of the study was to examine the impact of decentralization on operational efficiency, staff well-being, and teamwork on three inpatient units. Decentralized unit operations and the corresponding physical design solution were hypothesized to positively affect several concerns-productive use of nursing time, staff stress, walking distances, and teamwork, among others. With a wide adoption of the concept, empirical evidence on the impact of decentralization was warranted. A multimethod, before-and-after, quasi-experimental design was adopted for the study, focusing on five issues, namely, (1) how nurses spend their time, (2) walking distance, (3) acute stress, (4) productivity, and (5) teamwork. Data on all five issues were collected on three older units with centralized operational model (before move). The same set of data, with identical tools and measures, were collected on the same units after move in to new physical units with decentralized operational model. Data were collected during spring and fall of 2011. Documentation, nurse station use, medication room use, and supplies room use showed consistent change across the three units. Walking distance increased (statistically significant) on two of the three units. Self-reported level of collaboration decreased, although assessment of the physical facility for collaboration increased. Decentralized nursing and physical design models potentially result in quality of work improvements associated with documentation, medication, and supplies. However, there are unexpected consequences associated with walking, and staff collaboration and teamwork. The solution to the unexpected consequences may lie in operational interventions and greater emphasis on culture change. © The Author(s) 2015.

Stochastic availability analysis of operational data systems in the Deep Space Network

NASA Technical Reports Server (NTRS)

Issa, T. N.

1991-01-01

Existing availability models of standby redundant systems consider only an operator's performance and its interaction with the hardware performance. In the case of operational data systems in the Deep Space Network (DSN), in addition to an operator system interface, a controller reconfigures the system and links a standby unit into the network data path upon failure of the operating unit. A stochastic (Markovian) process technique is used to model and analyze the availability performance and occurrence of degradation due to partial failures are quantitatively incorporated into the model. Exact expressions of the steady state availability and proportion degraded performance measures are derived for the systems under study. The interaction among the hardware, operator, and controller performance parameters and that interaction's effect on data availability are evaluated and illustrated for an operational data processing system.

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.2665 - What if all the qualified operators are temporarily not accessible?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator... accessible and that you are resuming operation. Model Rule—Emission Limitations and Operating Limits ...

40 CFR 60.2665 - What if all the qualified operators are temporarily not accessible?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator... accessible and that you are resuming operation. Model Rule—Emission Limitations and Operating Limits ...

Successful completion of a cyclic ground test of a mercury ion auxiliary propulsion system

NASA Technical Reports Server (NTRS)

Francisco, David R.; Low, Charles A., Jr.; Power, John L.

1988-01-01

An engineering model Ion Auxiliary Propulsion System (IAPS) 8-cm thruster (S/N 905) has completed a life test at NASA Lewis Research Center. The mercury ion thruster successfully completed and exceeded the test goals of 2557 on/off cycles and 7057 hr of operation at full thrust. The final 1200 cycles and 3600 hr of the life test were conducted using an engineering model of the IAPS power electronics unit (PEU) and breadboard digital controller and interface unit (DCIU). This portion of the test is described in this paper with a charted history of thruster operating parameters and off-normal events. Performance and operating characteristics were constant throughout the test with only minor variations. The engineering model power electronics unit operated without malfunction; the flight software in the digital controller and interface unit was exercised and verified. Post-test inspection of the thruster revealed facility enhanced accelerator grid erosion but overall the thruster was in good condition. It was concluded that the thruster performance was not drastically degraded by time or cycles. Additional cyclic testing is currently under consideration.

Successful completion of a cyclic ground test of a mercury Ion Auxiliary Propulsion System

NASA Technical Reports Server (NTRS)

Francisco, David R.; Low, Charles A., Jr.; Power, John L.

1988-01-01

An engineering model Ion Auxiliary Propulsion System (IAPS) 8-cm thruster (S/N 905) has completed a life test at NASA Lewis Research Center. The mercury ion thruster successfully completed and exceeded the test goals of 2557 on/off cycles and 7057 hr of operation at full thrust. The final 1200 cycles and 3600 hr of the life test were conducted using an engineering model of the IAPS power electronics unit (PEU) and breadboard digital controller and interface unit (DCIU). This portion of the test is described in this paper with a charted history of thruster operating parameters and off-normal events. Performance and operating characteristics were constant throughout the test with only minor variations. The engineering model power electronics unit operated without malfunction; the flight software in the digital controller and interface unit was exercised and verified. Post-test inspection of the thruster revealed facility enhanced accelerator grid erosion but overall the thruster was in good condition. It was concluded that the thruster performance was not drastically degraded by time or cycles. Additional cyclic testing is currently under consideration.

How do strategic decisions and operative practices affect operating room productivity?

PubMed

Peltokorpi, Antti

2011-12-01

Surgical operating rooms are cost-intensive parts of health service production. Managing operating units efficiently is essential when hospitals and healthcare systems aim to maximize health outcomes with limited resources. Previous research about operating room management has focused on studying the effect of management practices and decisions on efficiency by utilizing mainly modeling approach or before-after analysis in single hospital case. The purpose of this research is to analyze the synergic effect of strategic decisions and operative management practices on operating room productivity and to use a multiple case study method enabling statistical hypothesis testing with empirical data. 11 hypotheses that propose connections between the use of strategic and operative practices and productivity were tested in a multi-hospital study that included 26 units. The results indicate that operative practices, such as personnel management, case scheduling and performance measurement, affect productivity more remarkably than do strategic decisions that relate to, e.g., units' size, scope or academic status. Units with different strategic positions should apply different operative practices: Focused hospital units benefit most from sophisticated case scheduling and parallel processing whereas central and ambulatory units should apply flexible working hours, incentives and multi-skilled personnel. Operating units should be more active in applying management practices which are adequate for their strategic orientation.

An approach to developing an integrated pyroprocessing simulator

NASA Astrophysics Data System (ADS)

Lee, Hyo Jik; Ko, Won Il; Choi, Sung Yeol; Kim, Sung Ki; Kim, In Tae; Lee, Han Soo

2014-02-01

Pyroprocessing has been studied for a decade as one of the promising fuel recycling options in Korea. We have built a pyroprocessing integrated inactive demonstration facility (PRIDE) to assess the feasibility of integrated pyroprocessing technology and scale-up issues of the processing equipment. Even though such facility cannot be replaced with a real integrated facility using spent nuclear fuel (SF), many insights can be obtained in terms of the world's largest integrated pyroprocessing operation. In order to complement or overcome such limited test-based research, a pyroprocessing Modelling and simulation study began in 2011. The Korea Atomic Energy Research Institute (KAERI) suggested a Modelling architecture for the development of a multi-purpose pyroprocessing simulator consisting of three-tiered models: unit process, operation, and plant-level-model. The unit process model can be addressed using governing equations or empirical equations as a continuous system (CS). In contrast, the operation model describes the operational behaviors as a discrete event system (DES). The plant-level model is an integrated model of the unit process and an operation model with various analysis modules. An interface with different systems, the incorporation of different codes, a process-centered database design, and a dynamic material flow are discussed as necessary components for building a framework of the plant-level model. As a sample model that contains methods decoding the above engineering issues was thoroughly reviewed, the architecture for building the plant-level-model was verified. By analyzing a process and operation-combined model, we showed that the suggested approach is effective for comprehensively understanding an integrated dynamic material flow. This paper addressed the current status of the pyroprocessing Modelling and simulation activity at KAERI, and also predicted its path forward.

An approach to developing an integrated pyroprocessing simulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Hyo Jik; Ko, Won Il; Choi, Sung Yeol

Pyroprocessing has been studied for a decade as one of the promising fuel recycling options in Korea. We have built a pyroprocessing integrated inactive demonstration facility (PRIDE) to assess the feasibility of integrated pyroprocessing technology and scale-up issues of the processing equipment. Even though such facility cannot be replaced with a real integrated facility using spent nuclear fuel (SF), many insights can be obtained in terms of the world's largest integrated pyroprocessing operation. In order to complement or overcome such limited test-based research, a pyroprocessing Modelling and simulation study began in 2011. The Korea Atomic Energy Research Institute (KAERI) suggestedmore » a Modelling architecture for the development of a multi-purpose pyroprocessing simulator consisting of three-tiered models: unit process, operation, and plant-level-model. The unit process model can be addressed using governing equations or empirical equations as a continuous system (CS). In contrast, the operation model describes the operational behaviors as a discrete event system (DES). The plant-level model is an integrated model of the unit process and an operation model with various analysis modules. An interface with different systems, the incorporation of different codes, a process-centered database design, and a dynamic material flow are discussed as necessary components for building a framework of the plant-level model. As a sample model that contains methods decoding the above engineering issues was thoroughly reviewed, the architecture for building the plant-level-model was verified. By analyzing a process and operation-combined model, we showed that the suggested approach is effective for comprehensively understanding an integrated dynamic material flow. This paper addressed the current status of the pyroprocessing Modelling and simulation activity at KAERI, and also predicted its path forward.« less

Operating cost model for local service airlines

NASA Technical Reports Server (NTRS)

Anderson, J. L.; Andrastek, D. A.

1976-01-01

Several mathematical models now exist which determine the operating economics for a United States trunk airline. These models are valuable in assessing the impact of new aircraft into an airline's fleet. The use of a trunk airline cost model for the local service airline does not result in representative operating costs. A new model is presented which is representative of the operating conditions and resultant costs for the local service airline. The calculated annual direct and indirect operating costs for two multiequipment airlines are compared with their actual operating experience.

The Operation Mechanisms of External Quality Assurance Frameworks of Foreign Higher Education and Implications for Graduate Education

ERIC Educational Resources Information Center

Lin, Mengquan; Chang, Kai; Gong, Le

2016-01-01

The higher education quality evaluation and assurance frameworks and their operating mechanisms of countries such as the United Kingdom, France, and the United States show that higher education systems, traditional culture, and social background all impact quality assurance operating mechanisms. A model analysis of these higher education quality…

A Constrained and Versioned Data Model for TEAM Data

NASA Astrophysics Data System (ADS)

Andelman, S.; Baru, C.; Chandra, S.; Fegraus, E.; Lin, K.

2009-04-01

The objective of the Tropical Ecology Assessment and Monitoring Network (www.teamnetwork.org) is "To generate real time data for monitoring long-term trends in tropical biodiversity through a global network of TEAM sites (i.e. field stations in tropical forests), providing an early warning system on the status of biodiversity to effectively guide conservation action". To achieve this, the TEAM Network operates by collecting data via standardized protocols at TEAM Sites. The standardized TEAM protocols include the Climate, Vegetation and Terrestrial Vertebrate Protocols. Some sites also implement additional protocols. There are currently 7 TEAM Sites with plans to grow the network to 15 by June 30, 2009 and 50 TEAM Sites by the end of 2010. At each TEAM Site, data is gathered as defined by the protocols and according to a predefined sampling schedule. The TEAM data is organized and stored in a database based on the TEAM spatio-temporal data model. This data model is at the core of the TEAM Information System - it consumes and executes spatio-temporal queries, and analytical functions that are performed on TEAM data, and defines the object data types, relationships and operations that maintain database integrity. The TEAM data model contains object types including types for observation objects (e.g. bird, butterfly and trees), sampling unit, person, role, protocol, site and the relationship of these object types. Each observation data record is a set of attribute values of an observation object and is always associated with a sampling unit, an observation timestamp or time interval, a versioned protocol and data collectors. The operations on the TEAM data model can be classified as read operations, insert operations and update operations. Following are some typical operations: The operation get(site, protocol, [sampling unit block, sampling unit,] start time, end time) returns all data records using the specified protocol and collected at the specified site, block, sampling unit and time range. The operation insertSamplingUnit(sampling unit, site, protocol) saves a new sampling unit into the data model and links it with the site and protocol. The operation updateSampligUnit(sampling_unit_id, attribute, value) changes the attribute (e.g. latitude or longitude) of the sampling unit to the specified value. The operation insertData(observation record, site, protocol, sampling unit, timestamps, data collectors) saves a new observation record into the database and associates it with specified objects. The operation updateData(protocol, data_id, attribute, value) modifies the attribute of an existing observation record to the specified value. All the insert or update operations require: 1) authorization to ensure the user has necessary privileges to perform the operation; 2) timestamp validation to ensure the observation timestamps are in the designated time range specified in the sampling schedule; 3) data validation to check that the data records use correct taxonomy terms and data values. No authorization is performed for get operations, but under some specific condition, a username may be required for the purpose of authentication. Along with the validations above, the TEAM data model also supports human based data validation on observed data through the Data Review subsystem to ensure data quality. The data review is implemented by adding two attributes review_tag and review_comment to each observation data record. The attribute review_tag is used by a reviewer to specify the quality of data, and the attribute review_comment is for reviewers to give more information when a problem is identified. The review_tag attribute can be populated by either the system conducting QA/QC tests or by pre-specified scientific experts. The following is the review operation, which is actually a special case of the operation updateData: The operation updateReview(protocol, data_id, judgment, comment) sets the attribute review_tag and review_comment to the specified values. By systematically tracking every step, The TEAM data model can roll back to any previous state. This is achieved by introducing a historical data container for each editable object type. When the operation updateData is applied to an object to modify its attribute, the object will be tagged with the current timestamp and the name of the user who conducts the operation, the tagged object will then be moved into the historical data container, and finally a new object will be created with the new value for the specified attribute. The diagram illustrates the architecture of the TEAM data management system. A data collector can use the Data Ingestion subsystem to load new data records into the TEAM data model. The system establishes a first level of review (i.e. meets minimum data standards via QA/QC tests). Further review is done via experts and they can verify and provide their comments on data records through the Data Review subsystem. The data editor can then address data records based on the reviewer's comments. Users can use the Data Query and Download application to find data by sites, protocols and time ranges. The Data Query and Download system packages selected data with the data license and important metadata information into a single package and delivers it to the user.

Development of the Integrated Biomass Supply Analysis and Logistics Model (IBSAL)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sokhansanj, Shahabaddine; Webb, Erin; Turhollow Jr, Anthony F

2008-06-01

The Integrated Biomass Supply & Logistics (IBSAL) model is a dynamic (time dependent) model of operations that involve collection, harvest, storage, preprocessing, and transportation of feedstock for use at a biorefinery. The model uses mathematical equations to represent individual unit operations. These unit operations can be assembled by the user to represent the working rate of equipment and queues to represent storage at facilities. The model calculates itemized costs, energy input, and carbon emissions. It estimates resource requirements and operational characteristics of the entire supply infrastructure. Weather plays an important role in biomass management and thus in IBSAL, dictating themore » moisture content of biomass and whether or not it can be harvested on a given day. The model calculates net biomass yield based on a soil conservation allowance (for crop residue) and dry matter losses during harvest and storage. This publication outlines the development of the model and provides examples of corn stover harvest and logistics.« less

Model of Rescue Units Control in Event of Potential Emergency

NASA Astrophysics Data System (ADS)

Kalach, A. V.; Kravchenko, A. S.; Soloviev, A. S.; Nesterov, A. A.

2018-05-01

A problem of organization and efficiency improvement of the system controlling the rescue units of the Ministry of Civil Defense and Emergency Response of the Russian Federation considered using the example of potential hydrological emergency, a model of a system for controlling rescue units in the event of potential hydrological emergency. The problem solution is based on mathematical models of operational control of rescue units and assessment of a hydrological situation of area flooding.

Simulating Sustainment for an Unmanned Logistics System Concept of Operation in Support of Distributed Operations

DTIC Science & Technology

2017-06-01

designed experiment to model and explore a ship-to-shore logistics process supporting dispersed units via three types of ULSs, which vary primarily in...systems, simulation, discrete event simulation, design of experiments, data analysis, simplekit, nearly orthogonal and balanced designs 15. NUMBER OF... designed experiment to model and explore a ship-to-shore logistics process supporting dispersed units via three types of ULSs, which vary primarily

Two Decades of WRF/CMAQ simulations over the continental United States: New approaches for performing dynamic model evaluation and determining confidence limits for ozone exceedances

EPA Science Inventory

Confidence in the application of models for forecasting and regulatory assessments is furthered by conducting four types of model evaluation: operational, dynamic, diagnostic, and probabilistic. Operational model evaluation alone does not reveal the confidence limits that can be ...

Improving the Composability of Department of Defense Models and Simulations

DTIC Science & Technology

2003-01-01

Simulations 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7...bibliographical references. “MG-101.” ISBN 0-8330-3525-8 (pbk. : alk. paper) 1. Military art and science— United States—Mathematical models. 2...Military art and science— United States—Simulation methods. 3. Operations research. 4. Military research— United States. 5. Military planning— United States

Creation operator for spinons in one dimension

DOE Office of Scientific and Technical Information (OSTI.GOV)

Talstra, J.C.; Strong, S.P.

1997-09-01

We propose a definition for a creation operator for the spinon, the fractional statistics elementary excitation of the Haldane-Shastry model, and give numerical and analytical evidence that our operator creates a single spinon with nearly unit amplitude in the Heisenberg model with inverse squared exchange. We then discuss how the operator is useful in more general contexts such as studying the underlying spinons of other spin-chain models, like the XXX and XY model, and of the one-dimensional Hubbard model. {copyright} {ital 1997} {ital The American Physical Society}

Modeling of unit operating considerations in generating-capacity reliability evaluation. Volume 2. Computer-program documentation. Final report. [GENESIS, OPCON and OPPLAN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, A.D.; Ayoub, A.K.; Singh, C.

1982-07-01

This report describes the structure and operation of prototype computer programs developed for a Monte Carlo simulation model, GENESIS, and for two analytical models, OPCON and OPPLAN. It includes input data requirements and sample test cases.

Modeling Operations Other Than War: Non-Combatants in Combat Modeling

DTIC Science & Technology

1994-09-01

supposition that non-combatants are an essential feature in OOTW. The model proposal includes a methodology for civilian unit decision making . The model...combatants are an essential feature in OOTW. The model proposal includes a methodology for civilian unit decision making . Thi- model also includes...numerical example demonstrated that the model appeared to perform in an acceptable manner, in that it produced output within a reasonable range. During the

Computer simulation of on-orbit manned maneuvering unit operations

NASA Technical Reports Server (NTRS)

Stuart, G. M.; Garcia, K. D.

1986-01-01

Simulation of spacecraft on-orbit operations is discussed in reference to Martin Marietta's Space Operations Simulation laboratory's use of computer software models to drive a six-degree-of-freedom moving base carriage and two target gimbal systems. In particular, key simulation issues and related computer software models associated with providing real-time, man-in-the-loop simulations of the Manned Maneuvering Unit (MMU) are addressed with special attention given to how effectively these models and motion systems simulate the MMU's actual on-orbit operations. The weightless effects of the space environment require the development of entirely new devices for locomotion. Since the access to space is very limited, it is necessary to design, build, and test these new devices within the physical constraints of earth using simulators. The simulation method that is discussed here is the technique of using computer software models to drive a Moving Base Carriage (MBC) that is capable of providing simultaneous six-degree-of-freedom motions. This method, utilized at Martin Marietta's Space Operations Simulation (SOS) laboratory, provides the ability to simulate the operation of manned spacecraft, provides the pilot with proper three-dimensional visual cues, and allows training of on-orbit operations. The purpose here is to discuss significant MMU simulation issues, the related models that were developed in response to these issues and how effectively these models simulate the MMU's actual on-orbiter operations.

Equipment of the binary-cycle geothermal power unit at the Pauzhet geothermal power station

NASA Astrophysics Data System (ADS)

Tomarov, G. V.; Nikol'skii, A. I.; Semenov, V. N.; Shipkov, A. A.

2014-06-01

The equipment of and technological processes in the pilot industrial model of the domestically produced binary-cycle geothermal power unit operating on the discharge separate at the Pauzhet geothermal power station are considered. The development principles, the design and operational features, and the data on selecting the metal in manufacturing the main equipment of the 2.5-MW binary power unit of the geothermal power station are described.

Renormalization of Seasonals in the Additive Seasonal Model: Is it Necessary?

DTIC Science & Technology

1984-02-01

recommended that qlass, headliqhts, and parkinq liqhts, the radiator, and other parts of the automobile which may be damaqed be covered with plywood...34Flying Automobile ", the AIR-6, and then a two-place monoplane, the AIR-7. A. S. Yakovlev was assigned as Supervisor of the Design Bureau for...operational unit, the microprogrammed control unit, the operating, permanent, and reprogrammable memory, the input-output unit, and the system of

A Study of Wind Turbine Comprehensive Operational Assessment Model Based on EM-PCA Algorithm

NASA Astrophysics Data System (ADS)

Zhou, Minqiang; Xu, Bin; Zhan, Yangyan; Ren, Danyuan; Liu, Dexing

2018-01-01

To assess wind turbine performance accurately and provide theoretical basis for wind farm management, a hybrid assessment model based on Entropy Method and Principle Component Analysis (EM-PCA) was established, which took most factors of operational performance into consideration and reach to a comprehensive result. To verify the model, six wind turbines were chosen as the research objects, the ranking obtained by the method proposed in the paper were 4#>6#>1#>5#>2#>3#, which are completely in conformity with the theoretical ranking, which indicates that the reliability and effectiveness of the EM-PCA method are high. The method could give guidance for processing unit state comparison among different units and launching wind farm operational assessment.

Setting up a mobile dental practice within your present office structure.

PubMed

Morreale, James P; Dimitry, Susan; Morreale, Mark; Fattore, Isabella

2005-02-01

Different service models have emerged in Canada and the United States to address the issue of senior citizens' lack of access to comprehensive dental care. Over the past decade, one such model, the use of mobile dental service units, has emerged as a practical strategy. This article describes a mobile unit, operated as an adjunct to the general practitioner's office and relying mainly on existing office resources, both human and capital, to deliver services at long-term care institutions. The essential components of a profitable geriatric mobile unit are described, including education, equipment, marketing research and development, and human resource management. Issues related to patient consent and operating expenditures are also discussed. Data from one practitioner's mobile dental unit, in Hamilton, Ontario, are presented to demonstrate the feasibility and profitability of this approach.

Self-organization comprehensive real-time state evaluation model for oil pump unit on the basis of operating condition classification and recognition

NASA Astrophysics Data System (ADS)

Liang, Wei; Yu, Xuchao; Zhang, Laibin; Lu, Wenqing

2018-05-01

In oil transmission station, the operating condition (OC) of an oil pump unit sometimes switches accordingly, which will lead to changes in operating parameters. If not taking the switching of OCs into consideration while performing a state evaluation on the pump unit, the accuracy of evaluation would be largely influenced. Hence, in this paper, a self-organization Comprehensive Real-Time State Evaluation Model (self-organization CRTSEM) is proposed based on OC classification and recognition. However, the underlying model CRTSEM is built through incorporating the advantages of Gaussian Mixture Model (GMM) and Fuzzy Comprehensive Evaluation Model (FCEM) first. That is to say, independent state models are established for every state characteristic parameter according to their distribution types (i.e. the Gaussian distribution and logistic regression distribution). Meanwhile, Analytic Hierarchy Process (AHP) is utilized to calculate the weights of state characteristic parameters. Then, the OC classification is determined by the types of oil delivery tasks, and CRTSEMs of different standard OCs are built to constitute the CRTSEM matrix. On the other side, the OC recognition is realized by a self-organization model that is established on the basis of Back Propagation (BP) model. After the self-organization CRTSEM is derived through integration, real-time monitoring data can be inputted for OC recognition. At the end, the current state of the pump unit can be evaluated by using the right CRTSEM. The case study manifests that the proposed self-organization CRTSEM can provide reasonable and accurate state evaluation results for the pump unit. Besides, the assumption that the switching of OCs will influence the results of state evaluation is also verified.

Operational integration in primary health care: patient encounters and workflows.

PubMed

Sifaki-Pistolla, Dimitra; Chatzea, Vasiliki-Eirini; Markaki, Adelais; Kritikos, Kyriakos; Petelos, Elena; Lionis, Christos

2017-11-29

Despite several countrywide attempts to strengthen and standardise the primary healthcare (PHC) system, Greece is still lacking a sustainable, policy-based model of integrated services. The aim of our study was to identify operational integration levels through existing patient care pathways and to recommend an alternative PHC model for optimum integration. The study was part of a large state-funded project, which included 22 randomly selected PHC units located across two health regions of Greece. Dimensions of operational integration in PHC were selected based on the work of Kringos and colleagues. A five-point Likert-type scale, coupled with an algorithm, was used to capture and transform theoretical framework features into measurable attributes. PHC services were grouped under the main categories of chronic care, urgent/acute care, preventive care, and home care. A web-based platform was used to assess patient pathways, evaluate integration levels and propose improvement actions. Analysis relied on a comparison of actual pathways versus optimal, the latter ones having been identified through literature review. Overall integration varied among units. The majority (57%) of units corresponded to a basic level. Integration by type of PHC service ranged as follows: basic (86%) or poor (14%) for chronic care units, poor (78%) or basic (22%) for urgent/acute care units, basic (50%) for preventive care units, and partial or basic (50%) for home care units. The actual pathways across all four categories of PHC services differed from those captured in the optimum integration model. Certain similarities were observed in the operational flows between chronic care management and urgent/acute care management. Such similarities were present at the highest level of abstraction, but also in common steps along the operational flows. Existing patient care pathways were mapped and analysed, and recommendations for an optimum integration PHC model were made. The developed web platform, based on a strong theoretical framework, can serve as a robust integration evaluation tool. This could be a first step towards restructuring and improving PHC services within a financially restrained environment.

Analysis of Unit-Level Changes in Operations with Increased SPP Wind from EPRI/LCG Balancing Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadley, Stanton W

2012-01-01

Wind power development in the United States is outpacing previous estimates for many regions, particularly those with good wind resources. The pace of wind power deployment may soon outstrip regional capabilities to provide transmission and integration services to achieve the most economic power system operation. Conversely, regions such as the Southeastern United States do not have good wind resources and will have difficulty meeting proposed federal Renewable Portfolio Standards with local supply. There is a growing need to explore innovative solutions for collaborating between regions to achieve the least cost solution for meeting such a renewable energy mandate. The Departmentmore » of Energy funded the project 'Integrating Midwest Wind Energy into Southeast Electricity Markets' to be led by EPRI in coordination with the main authorities for the regions: SPP, Entergy, TVA, Southern Company and OPC. EPRI utilized several subcontractors for the project including LCG, the developers of the model UPLAN. The study aims to evaluate the operating cost benefits of coordination of scheduling and balancing for Southwest Power Pool (SPP) wind transfers to Southeastern Electric Reliability Council (SERC) Balancing Authorities (BAs). The primary objective of this project is to analyze the benefits of regional cooperation for integrating mid-western wind energy into southeast electricity markets. Scenarios were defined, modeled and investigated to address production variability and uncertainty and the associated balancing of large quantities of wind power in SPP and delivery to energy markets in the southern regions of the SERC. DOE funded Oak Ridge National Laboratory to provide additional support to the project, including a review of results and any side analysis that may provide additional insight. This report is a unit-by-unit analysis of changes in operations due to the different scenarios used in the overall study. It focuses on the change in capacity factors and the number of start-ups required for each unit since those criteria summarize key aspects of plant operations, how often are they called upon and how much do they operate. The primary analysis of the overall project is based on security-constrained unit commitment (SCUC) and economic dispatch (SCED) simulations of the SPP-SERC regions as modeled for the year 2022. The SCUC/SCED models utilized for the project were developed through extensive consultation with the project utility partners, to ensure the various regions and operational practices are represented as best as possible in the model. SPP, Entergy, Oglethorpe Power Company (OPC), Southern Company, and the Tennessee Valley Authority (TVA) actively participated in the project providing input data for the models and review of simulation results and conclusions. While other SERC utility systems are modeled, the listed SERC utilities were explicitly included as active participants in the project due to the size of their load and relative proximity to SPP for importing wind energy.« less

PUP: An Architecture to Exploit Parallel Unification in Prolog

DTIC Science & Technology

1988-03-01

environment stacking mo del similar to the Warren Abstract Machine [23] since it has been shown to be super ior to other known models (see [21]). The storage...execute in groups of independent operations. Unifications belonging to different group s may not overlap. Also unification operations belonging to the...since all parallel operations on the unification units must complete before any of the units can star t executing the next group of parallel

Robust Unit Commitment Considering Uncertain Demand Response

DOE PAGES

Liu, Guodong; Tomsovic, Kevin

2014-09-28

Although price responsive demand response has been widely accepted as playing an important role in the reliable and economic operation of power system, the real response from demand side can be highly uncertain due to limited understanding of consumers' response to pricing signals. To model the behavior of consumers, the price elasticity of demand has been explored and utilized in both research and real practice. However, the price elasticity of demand is not precisely known and may vary greatly with operating conditions and types of customers. To accommodate the uncertainty of demand response, alternative unit commitment methods robust to themore » uncertainty of the demand response require investigation. In this paper, a robust unit commitment model to minimize the generalized social cost is proposed for the optimal unit commitment decision taking into account uncertainty of the price elasticity of demand. By optimizing the worst case under proper robust level, the unit commitment solution of the proposed model is robust against all possible realizations of the modeled uncertain demand response. Numerical simulations on the IEEE Reliability Test System show the e ectiveness of the method. Finally, compared to unit commitment with deterministic price elasticity of demand, the proposed robust model can reduce the average Locational Marginal Prices (LMPs) as well as the price volatility.« less

Evaluation of Selected Chemical Processes for Production of Low-cost Silicon, Phase 3

NASA Technical Reports Server (NTRS)

Blocher, J. M., Jr.; Browning, M. F.

1979-01-01

The construction of the 50 MT Si/year experimental process system development unit was deferred until FY 1980, and the fluidized bed, zinc vaporizer, by-product condenser, and electrolytic cell were combined with auxiliary units, capable of supporting 8-hour batchwise operation, to form the process development unit (PDU), which is scheduled to be in operation by October 1, 1979. The design of the PDU and objectives of its operation are discussed. Experimental program support activities described relate to: (1) a wetted-wall condensor; (2) fluidized-bed modeling; (3) zinc chloride electrolysis; and (4) zinc vaporizer.

Conceptual design and feasibility evaluation model of a 10 to the 8th power bit oligatomic mass memory. Volume 3: Operation manual

NASA Technical Reports Server (NTRS)

Horst, R. L.; Nordstrom, M. J.

1972-01-01

An operation manual is presented for the oligatomic mass memory feasibility model. It includes a brief description of the memory and exerciser units, a description of the controls and their functions, the operating procedures, the test points and adjustments, and the circuit diagram.

40 CFR Table 3 to Subpart Dddd of... - Model Rule-Operating Limits for Wet Scrubbers

Code of Federal Regulations, 2010 CFR

2010-07-01

... Scrubbers 3 Table 3 to Subpart DDDD of Part 60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...—Model Rule—Operating Limits for Wet Scrubbers For these operating parameters You must establish these... intermittent units) a Pressure drop across the wet scrubber or amperage to wet scrubber Minimum pressure drop...

40 CFR Table 3 to Subpart Dddd of... - Model Rule-Operating Limits for Wet Scrubbers

Code of Federal Regulations, 2011 CFR

2011-07-01

... Scrubbers 3 Table 3 to Subpart DDDD of Part 60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...—Model Rule—Operating Limits for Wet Scrubbers For these operating parameters You must establish these... intermittent units) a Pressure drop across the wet scrubber or amperage to wet scrubber Minimum pressure drop...

"Life without nuclear power": A nuclear plant retirement formulation model and guide based on economics. San Onofre Nuclear Generating Station case: Economic impacts and reliability considerations leading to plant retirement

NASA Astrophysics Data System (ADS)

Wasko, Frank

Traditionally, electric utilities have been slow to change and very bureaucratic in nature. This culture, in and of itself, has now contributed to a high percentage of United States electric utilities operating uneconomical nuclear plants (Crooks, 2014). The economic picture behind owning and operating United States nuclear plants is less than favorable for many reasons including rising fuel, capital and operating costs (EUCG, 2012). This doctoral dissertation is specifically focused on life without nuclear power. The purpose of this dissertation is to create a model and guide that will provide electric utilities who currently operate or will operate uneconomical nuclear plants the opportunity to economically assess whether or not their nuclear plant should be retired. This economic assessment and stakeholder analysis will provide local government, academia and communities the opportunity to understand how Southern California Edison (SCE) embraced system upgrade import and "voltage support" opportunities to replace "base load" generation from San Onofre Nuclear Generating Station (SONGS) versus building new replacement generation facilities. This model and guide will help eliminate the need to build large replacement generation units as demonstrated in the SONGS case analysis. The application of The Nuclear Power Retirement Model and Guide will provide electric utilities with economic assessment parameters and an evaluation assessment progression needed to better evaluate when an uneconomical nuclear plant should be retired. It will provide electric utilities the opportunity to utilize sound policy, planning and development skill sets when making this difficult decision. There are currently 62 nuclear power plants (with 100 nuclear reactors) operating in the United States (EIA, 2014). From this group, 38 are at risk of early retirement based on the work of Cooper (2013). As demonstrated in my model, 35 of the 38 nuclear power plants qualify to move to the economic assessment review and then on to the stakeholder cost benefit analysis (if model qualifications are met) leading to a final plant retirement decision. This application via the model and guide, in turn, will lead electric utilities to explore system upgrade import opportunities and mitigation measures versus building new replacement generation facilities. United States nuclear reactors are licensed for 40 years with a 20 year extension available prior to the expiration date (EIA, 2013). Since late 2012, electric power companies have announced the early retirement of four uneconomical nuclear power plants while other studies have indicated that as many as 70 percent of United States nuclear power plants are potentially at risk for early retirement (Crooks, 2014 and Cooper, 2013). A high percentage of these aforementioned nuclear plants have operating licenses that will not expire until 2030 and beyond. Thus, for the most part, replacement power contingency planning has not been initiated for these plants or is still in preliminary stages. The recent nuclear plant retirements are the first since 1998 (EIA, 2013). Decisions to retire the plants involved concerns over maintenance and repair costs as well as declining profitability (EIA, 2013). In addition, the Energy Information Administration (2010-2012) released data that demonstrated that the worst 25 percent of United States nuclear plants are far more expensive to operate and generate electricity than new gas plants. It is equally important to understand and explain the economic and power replacement implications to both ratepayers and end-users. A SONGS case study analysis will review the economic, operational and political challenges that SCE faced leading to the retirement decision of SONGS. As preface to the case study, replacement steam generators (RSGs) were installed in Unit 2 in 2009 and in Unit 3 in 2010. In January 2012, while Unit 2 was down for routine maintenance, a small leak was discovered inside a steam generator in Unit 3. Because of the situation, both units remained shut down to evaluate the cause of the leakage and to make repairs. SCE submitted plans to the Nuclear Regulatory Commission (NRC) to re-start Unit 2 at reduced power. However, concerns over the length of the review process and the high costs associated with steam generator repairs led SCE to retire both reactors (SCE SONGS Fact Sheets, 2012-2013). Finally, collaborative resource power replacement planning is needed more than ever as nuclear facilities in the United States are now being retired for economic related reasons (Crooks, 2014). This collaborative power replacement process and implementation must encompass all relevant stakeholders including state grid operators, ratepayers, shareholders and the electric utility company.

Competitive Electricity Market Regulation in the United States: A Primer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flores-Espino, Francisco; Tian, Tian; Chernyakhovskiy, Ilya

The electricity system in the United States is a complex mechanism where different technologies, jurisdictions and regulatory designs interact. Today, two major models for electricity commercialization operate in the United States. One is the regulated monopoly model, in which vertically integrated electricity providers are regulated by state commissions. The other is the competitive model, in which power producers can openly access transmission infrastructure and participate in wholesale electricity markets. This paper describes the origins, evolution, and current status of the regulations that enable competitive markets in the United States.

Use of Dynamic Models and Operational Architecture to Solve Complex Navy Challenges

NASA Technical Reports Server (NTRS)

Grande, Darby; Black, J. Todd; Freeman, Jared; Sorber, TIm; Serfaty, Daniel

2010-01-01

The United States Navy established 8 Maritime Operations Centers (MOC) to enhance the command and control of forces at the operational level of warfare. Each MOC is a headquarters manned by qualified joint operational-level staffs, and enabled by globally interoperable C41 systems. To assess and refine MOC staffing, equipment, and schedules, a dynamic software model was developed. The model leverages pre-existing operational process architecture, joint military task lists that define activities and their precedence relations, as well as Navy documents that specify manning and roles per activity. The software model serves as a "computational wind-tunnel" in which to test a MOC on a mission, and to refine its structure, staffing, processes, and schedules. More generally, the model supports resource allocation decisions concerning Doctrine, Organization, Training, Material, Leadership, Personnel and Facilities (DOTMLPF) at MOCs around the world. A rapid prototype effort efficiently produced this software in less than five months, using an integrated process team consisting of MOC military and civilian staff, modeling experts, and software developers. The work reported here was conducted for Commander, United States Fleet Forces Command in Norfolk, Virginia, code N5-0LW (Operational Level of War) that facilitates the identification, consolidation, and prioritization of MOC capabilities requirements, and implementation and delivery of MOC solutions.

Operations analysis (study 2.1): Payload designs for space servicing

NASA Technical Reports Server (NTRS)

Wolfe, R. R.

1974-01-01

Potential modes of operating in space in the space shuttle era are documented. The October 1973 NASA Mission Model provides a definition of various NASA and non-DOD automated payload configurations when employed in an expendable mode. The model also specifies a launch schedule for initial deployment of payloads as well as for subsequent replacements at periodic cycles. This model and its associated payload definitions serve as a foundation for the data presented in this report. The reference model has been revised to reflect automated space servicing of payloads as an operational concept instead of the existing expendable approach. The indication is that the bulk of a payload's subsystems and mission equipment require no support over the lifetime of the program. However, failure of a single unit could result in loss of the mission objectives. When space servicing is employed, the approach is to replace only that unit causing the anomaly. This concept affords an opportunity to standardize space replacable units, as well as to reduce the expense of logistics support, by allowing multiple servicing on any single upper stage/shuttle flight.

Operating unit time use is associated with anaesthesia type in below-knee surgery in adults.

PubMed

Lohela, T J; Chase, R P; Hiekkanen, T A; Kontinen, V K; Hynynen, M J

2017-03-01

Peripheral nerve blocks could reduce the operating unit and theatre time spent on high-risk patients who are particularly vulnerable to complications of general anaesthesia or have medications that prevent application of central neuraxial blocks. Medical record data of 617 and 254 elderly adults undergoing below-knee surgery in Jorvi and Meilahti hospitals (Helsinki University Hospital) between January 2010 and December 2012 were used to investigate the influence of anaesthetic technique on operating theatre times and on operating unit times using flexible parametric survival models. We report operating theatre and unit exit ratios (i.e. hazard ratios but using ratios of exit rates) for different types of anaesthesia. Adjusted analyses: In Jorvi Hospital, anaesthesia type was associated with large initial differentials in operating theatre times. The theatre exit ratios remained lower for general anaesthesia and central neuraxial blocks compared to peripheral nerve blocks until 30 min. In Meilahti Hospital, anaesthesia type did not influence theatre time, but was the best predictor of operating unit times. Compared to peripheral nerve blocks, the exit ratio remained lower for general anaesthesia until five operating unit hours in both hospitals and for central neuraxial blocks until 1 h in Meilahti Hospital and until 3 h in Jorvi Hospital. Holding area was used more in Jorvi Hospital compared to Meilahti Hospital. Peripheral nerve block anaesthesia reduces time spent in the operating unit and can reduce time spent in the operating theatre if induced in holding area outside of theatre. © 2017 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Additive Manufacturing (AM) in Expeditionary Operations: Current Needs, Technical Challenges, and Opportunities

DTIC Science & Technology

2016-06-01

site customization of existing models. The author performed an empirical study centered around a survey of United States Marine Corps (USMC) and United...recommends that more studies be performed to determine the best way forward for AM within the USMC and USN. 14. SUBJECT TERMS 3D printing, additive...customization of existing models. The author performed an em- pirical study centered around a survey of United States Marine Corps (USMC) and United

Development Of Simulation Model For Fluid Catalytic Cracking

NASA Astrophysics Data System (ADS)

Ghosh, Sobhan

2010-10-01

Fluid Catalytic Cracking (FCC) is the most widely used secondary conversion process in the refining industry, for producing gasoline, olefins, and middle distillate from heavier petroleum fractions. There are more than 500 units in the world with a total processing capacity of about 17 to 20% of the crude capacity. FCC catalyst is the highest consumed catalyst in the process industry. On one hand, FCC is quite flexible with respect to it's ability to process wide variety of crudes with a flexible product yield pattern, and on the other hand, the interdependence of the major operating parameters makes the process extremely complex. An operating unit is self balancing and some fluctuations in the independent parameters are automatically adjusted by changing the temperatures and flow rates at different sections. However, a good simulation model is very useful to the refiner to get the best out of the process, in terms of selection of the best catalyst, to cope up with the day to day changing of the feed quality and the demands of different products from FCC unit. In addition, a good model is of great help in designing the process units and peripherals. A simple empirical model is often adequate to monitor the day to day operations, but they are not of any use in handling the other problems such as, catalyst selection or, design / modification of the plant. For this, a kinetic based rigorous model is required. Considering the complexity of the process, large number of chemical species undergoing "n" number of parallel and consecutive reactions, it is virtually impossible to develop a simulation model based on the kinetic parameters. The most common approach is to settle for a semi empirical model. We shall take up the key issues for developing a FCC model and the contribution of such models in the optimum operation of the plant.

Integrated Electronic Warfare Systems Aboard the United States Navy 21st Century Warship

DTIC Science & Technology

2009-12-01

automated operation using a Human-In-the-Loop that could be integrated into existing and future combat systems. A model was developed that demonstrates...complete range of automated operation using a Human-In-the-Loop that could be integrated into existing and future combat systems. A model was developed...44 1. Base Case Model

Detection and analysis of part load and full load instabilities in a real Francis turbine prototype

NASA Astrophysics Data System (ADS)

Presas, Alexandre; Valentin, David; Egusquiza, Eduard; Valero, Carme

2017-04-01

Francis turbines operate in many cases out of its best efficiency point, in order to regulate their output power according to the instantaneous energy demand of the grid. Therefore, it is of paramount importance to analyse and determine the unstable operating points for these kind of units. In the framework of the HYPERBOLE project (FP7-ENERGY-2013-1; Project number 608532) a large Francis unit was investigated numerically, experimentally in a reduced scale model and also experimentally and numerically in the real prototype. This paper shows the unstable operating points identified during the experimental tests on the real Francis unit and the analysis of the main characteristics of these instabilities. Finally, it is shown that similar phenomena have been identified on previous research in the LMH (Laboratory for Hydraulic Machines, Lausanne) with the reduced scale model.

Performance and Operational Characteristics for a Dual Brayton Space Power System With Common Gas Inventory

NASA Technical Reports Server (NTRS)

Johnson, Paul K.; Mason, Lee S.

2006-01-01

This paper provides an analytical evaluation on the operation and performance of a dual Brayton common gas system. The NASA Glenn Research Center in-house computer program Closed Cycle System Simulation (CCSS) was used to construct a model of two identical 50 kWe-class recuperated closed-Brayton-cycle (CBC) power conversion units that share a common gas inventory and single heat source. As operating conditions for each CBC change, the total gas inventory is redistributed between the two units and overall system performance is affected. Several steady-state off-design operating points were analyzed by varying turbine inlet temperature and turbo-alternator shaft rotational speed to investigate the interaction of the two units.

Cost-effective retrofit technology for reducing peak power demand in small and medium commercial buildings

DOE PAGES

Nutaro, James J.; Fugate, David L.; Kuruganti, Teja; ...

2015-05-27

We describe a cost-effective retrofit technology that uses collective control of multiple rooftop air conditioning units to reduce the peak power consumption of small and medium commercial buildings. The proposed control uses a model of the building and air conditioning units to select an operating schedule for the air conditioning units that maintains a temperature set point subject to a constraint on the number of units that may operate simultaneously. A prototype of this new control system was built and deployed in a large gymnasium to coordinate four rooftop air conditioning units. Based on data collected while operating this prototype,more » we estimate that the cost savings achieved by reducing peak power consumption is sufficient to repay the cost of the prototype within a year.« less

Compressor and Turbine Models of Brayton Units for Space Nuclear Power Systems

NASA Astrophysics Data System (ADS)

Gallo, Bruno M.; El-Genk, Mohamed S.; Tournier, Jean-Michel

2007-01-01

Closed Brayton Cycles with centrifugal flow, single-shaft turbo-machines are being considered, with gas cooled nuclear reactors, to provide 10's to 100's of electrical power to support future space exploration missions and Lunar and Mars outposts. Such power system analysis is typically based on the cycle thermodynamics, for given operating pressures and temperatures and assumed polytropic efficiencies of the compressor and turbine of the Brayton energy conversion units. Thus the analysis results not suitable for modeling operation transients such as startup and changes in the electric load. To simulate these transients, accurate models of the turbine and compressor in the Brayton rotating unit, which calculate the changes in the compressor and turbine efficiencies with system operation are needed. This paper presents flow models that account for the design and dimensions of the compressor impeller and diffuser, and the turbine stator and rotor blades. These models calculate the various enthalpy losses and the polytropic efficiencies along with the pressure ratios of the turbine and compressor. The predictions of these models compare well with reported performance data of actual hardware. In addition, the results of a parametric analysis to map the operations of the compressor and turbine, as functions of the rotating shaft speed and inlet Mach number of the gas working fluid, are presented and discussed. The analysis used a binary mixture of He-Xe with a molecular weight of 40 g/mole as the working fluid.

Planning intensive care unit design using computer simulation modeling: optimizing integration of clinical, operational, and architectural requirements.

PubMed

OʼHara, Susan

2014-01-01

Nurses have increasingly been regarded as critical members of the planning team as architects recognize their knowledge and value. But the nurses' role as knowledge experts can be expanded to leading efforts to integrate the clinical, operational, and architectural expertise through simulation modeling. Simulation modeling allows for the optimal merge of multifactorial data to understand the current state of the intensive care unit and predict future states. Nurses can champion the simulation modeling process and reap the benefits of a cost-effective way to test new designs, processes, staffing models, and future programming trends prior to implementation. Simulation modeling is an evidence-based planning approach, a standard, for integrating the sciences with real client data, to offer solutions for improving patient care.

Calibration of Reduced Dynamic Models of Power Systems using Phasor Measurement Unit (PMU) Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Ning; Lu, Shuai; Singh, Ruchi

2011-09-23

Accuracy of a power system dynamic model is essential to the secure and efficient operation of the system. Lower confidence on model accuracy usually leads to conservative operation and lowers asset usage. To improve model accuracy, identification algorithms have been developed to calibrate parameters of individual components using measurement data from staged tests. To facilitate online dynamic studies for large power system interconnections, this paper proposes a model reduction and calibration approach using phasor measurement unit (PMU) data. First, a model reduction method is used to reduce the number of dynamic components. Then, a calibration algorithm is developed to estimatemore » parameters of the reduced model. This approach will help to maintain an accurate dynamic model suitable for online dynamic studies. The performance of the proposed method is verified through simulation studies.« less

Optimal Operation of Energy Storage in Power Transmission and Distribution

NASA Astrophysics Data System (ADS)

Akhavan Hejazi, Seyed Hossein

In this thesis, we investigate optimal operation of energy storage units in power transmission and distribution grids. At transmission level, we investigate the problem where an investor-owned independently-operated energy storage system seeks to offer energy and ancillary services in the day-ahead and real-time markets. We specifically consider the case where a significant portion of the power generated in the grid is from renewable energy resources and there exists significant uncertainty in system operation. In this regard, we formulate a stochastic programming framework to choose optimal energy and reserve bids for the storage units that takes into account the fluctuating nature of the market prices due to the randomness in the renewable power generation availability. At distribution level, we develop a comprehensive data set to model various stochastic factors on power distribution networks, with focus on networks that have high penetration of electric vehicle charging load and distributed renewable generation. Furthermore, we develop a data-driven stochastic model for energy storage operation at distribution level, where the distribution of nodal voltage and line power flow are modelled as stochastic functions of the energy storage unit's charge and discharge schedules. In particular, we develop new closed-form stochastic models for such key operational parameters in the system. Our approach is analytical and allows formulating tractable optimization problems. Yet, it does not involve any restricting assumption on the distribution of random parameters, hence, it results in accurate modeling of uncertainties. By considering the specific characteristics of random variables, such as their statistical dependencies and often irregularly-shaped probability distributions, we propose a non-parametric chance-constrained optimization approach to operate and plan energy storage units in power distribution girds. In the proposed stochastic optimization, we consider uncertainty from various elements, such as solar photovoltaic , electric vehicle chargers, and residential baseloads, in the form of discrete probability functions. In the last part of this thesis we address some other resources and concepts for enhancing the operation of power distribution and transmission systems. In particular, we proposed a new framework to determine the best sites, sizes, and optimal payment incentives under special contracts for committed-type DG projects to offset distribution network investment costs. In this framework, the aim is to allocate DGs such that the profit gained by the distribution company is maximized while each DG unit's individual profit is also taken into account to assure that private DG investment remains economical.

40 CFR 60.2645 - How do I obtain my operator qualification?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...

40 CFR 60.2650 - How do I maintain my operator qualification?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...

40 CFR 60.2650 - How do I maintain my operator qualification?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...

40 CFR 60.2645 - How do I obtain my operator qualification?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...

Fuzzy multiobjective models for optimal operation of a hydropower system

NASA Astrophysics Data System (ADS)

Teegavarapu, Ramesh S. V.; Ferreira, André R.; Simonovic, Slobodan P.

2013-06-01

Optimal operation models for a hydropower system using new fuzzy multiobjective mathematical programming models are developed and evaluated in this study. The models use (i) mixed integer nonlinear programming (MINLP) with binary variables and (ii) integrate a new turbine unit commitment formulation along with water quality constraints used for evaluation of reservoir downstream impairment. Reardon method used in solution of genetic algorithm optimization problems forms the basis for development of a new fuzzy multiobjective hydropower system optimization model with creation of Reardon type fuzzy membership functions. The models are applied to a real-life hydropower reservoir system in Brazil. Genetic Algorithms (GAs) are used to (i) solve the optimization formulations to avoid computational intractability and combinatorial problems associated with binary variables in unit commitment, (ii) efficiently address Reardon method formulations, and (iii) deal with local optimal solutions obtained from the use of traditional gradient-based solvers. Decision maker's preferences are incorporated within fuzzy mathematical programming formulations to obtain compromise operating rules for a multiobjective reservoir operation problem dominated by conflicting goals of energy production, water quality and conservation releases. Results provide insight into compromise operation rules obtained using the new Reardon fuzzy multiobjective optimization framework and confirm its applicability to a variety of multiobjective water resources problems.

The Regional Special Operations Headquarters: Franchising the NATO Model as a Hedge in Lean Times

DTIC Science & Technology

2012-04-01

1 AIR FORCE FELLOWS AIR UNIVERSITY THE REGIONAL SPECIAL OPERATIONS HEADQUARTERS: FRANCHISING THE NATO MODEL AS A HEDGE IN LEAN...Headquarters: Franchising The NATO Model As A Hedge In Lean Times 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d...it is not copyrighted, but is the property of the United States government. 3 The Regional Special Operations Headquarters: Franchising the

Model for Sucker-Rod Pumping Unit Operating Modes Analysis Based on SimMechanics Library

NASA Astrophysics Data System (ADS)

Zyuzev, A. M.; Bubnov, M. V.

2018-01-01

The article provides basic information about the process of a sucker-rod pumping unit (SRPU) model developing by means of SimMechanics library in the MATLAB Simulink environment. The model is designed for the development of a pump productivity optimal management algorithms, sensorless diagnostics of the plunger pump and pumpjack, acquisition of the dynamometer card and determination of a dynamic fluid level in the well, normalization of the faulty unit operation before troubleshooting is performed by staff as well as equilibrium ratio determining by energy indicators and outputting of manual balancing recommendations to achieve optimal power consumption efficiency. Particular attention is given to the application of various blocks from SimMechanics library to take into account the pumpjack construction principal characteristic and to obtain an adequate model. The article explains in depth the developed tools features for collecting and analysis of simulated mechanism data. The conclusions were drawn about practical implementation possibility of the SRPU modelling results and areas for further development of investigation.

Turbine Powered Simulator Calibration and Testing for Hybrid Wing Body Powered Airframe Integration

NASA Technical Reports Server (NTRS)

Shea, Patrick R.; Flamm, Jeffrey D.; Long, Kurtis R.; James, Kevin D.; Tompkins, Daniel M.; Beyar, Michael D.

2016-01-01

Propulsion airframe integration testing on a 5.75% scale hybrid wing body model us- ing turbine powered simulators was completed at the National Full-Scale Aerodynamics Complex 40- by 80-foot test section. Four rear control surface con gurations including a no control surface de ection con guration were tested with the turbine powered simulator units to investigate how the jet exhaust in uenced the control surface performance as re- lated to the resultant forces and moments on the model. Compared to ow-through nacelle testing on the same hybrid wing body model, the control surface e ectiveness was found to increase with the turbine powered simulator units operating. This was true for pitching moment, lift, and drag although pitching moment was the parameter of greatest interest for this project. With the turbine powered simulator units operating, the model pitching moment was seen to increase when compared to the ow-through nacelle con guration indicating that the center elevon and vertical tail control authority increased with the jet exhaust from the turbine powered simulator units.

The impacts of meeting a tight CO2 performance standard on the electric power sector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, Donald; Schmalzer, David; Nichols, Christopher

This paper presents innovative modeling of complex interactions among gas-fired generators, coal-fired power plants, and renewables (wind and solar) when pushed hard to reduce CO2 emissions. A hypothetical CO2 technology performance standard, giving rise to a shadow price on CO2 emissions, was specified as part of the study design. In this work we see gas generation rapidly replacing coal generation. To understand the fate of coal based generation, it is important to examine trends at a granular level. An important feature of our model, the Electricity Supply and Investment Model (ESIM) is that it contains a unit inventory with unitmore » characteristics and a memory of how each unit is operated over time. Cycling damages that individual coal units incur are a function of cumulative wear and tear over time. The expected remaining life of a cycled coal unit will depend on the severity of the cycling and for how many years. Deteriorating operating characteristics of a cycled unit over time results in higher operating costs, slipping down the dispatch loading order, and hence an acceleration of cycling damage, that is, a viscous circle of decline. The rate of CFPP retirements will increase for lower gas prices, higher price on CO2 emissions, and greater penetration of variable and intermittent renewables. Published by Elsevier B.V.« less

A Review of Operational Water Consumption and Withdrawal Factors for Electricity Generating Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macknick, Jordan; Newmark, Robin; Heath, Garvin

2011-03-01

This report provides estimates of operational water withdrawal and water consumption factors for electricity generating technologies in the United States. Estimates of water factors were collected from published primary literature and were not modified except for unit conversions. The presented water factors may be useful in modeling and policy analyses where reliable power plant level data are not available.

40 CFR 60.2805 - Am I required to apply for and obtain a Title V operating permit for my unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model... permit for my unit? Yes. Each CISWI unit and air curtain incinerator subject to standards under this...

40 CFR 60.2805 - Am I required to apply for and obtain a Title V operating permit for my unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model... permit for my unit? Yes. Each CISWI unit and air curtain incinerator subject to standards under this...

40 CFR 60.2640 - When must the operator training course be completed?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator...

40 CFR 60.2640 - When must the operator training course be completed?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator...

Toward a best practice model for managed lanes in Texas.

DOT National Transportation Integrated Search

2013-09-01

Increasing implementation of managed lanes in the : United States : Katy Freeway Managed Lanes : (KML) offers lessons learned : for other projects : First operational, multilane, : variably priced, managed facility : in Texas : Became oper...

Automated Instructional Management Systems (AIMS) Version III, Operator's Guide.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

This manual gives the instructions necessary to understand and operate the Automated Instructional Management System (AIMS), utilizing IBM System 360, Model 30/Release 20 Disk Operating System, and the OpScan 100 System Reader and Tape Unit. It covers the AIMS III system initialization, system and operational input, requirements, master response…

Research on Power System Scheduling Improving Wind Power Accommodation Considering Thermal Energy Storage and Flexible Load

NASA Astrophysics Data System (ADS)

Zou, Chenlu; Cui, Xue; Wang, Heng; Zhou, Bin; Liu, Yang

2018-01-01

In the case of rapid development of wind power and heavy wind curtailment, the study of wind power accommodation of combined heat and power system has become the focus of attention. A two-stage scheduling model contains of wind power, thermal energy storage, CHP unit and flexible load were constructed. This model with the objective function of minimizing wind curtailment and the operation cost of units while taking into account of the total coal consumption of units, constraint of thermal energy storage and electricity-heat characteristic of CHP. This paper uses MICA to solve the problem of too many constraints and make the solution more feasible. A numerical example showed that the two stage decision scheduling model can consume more wind power, and it could provide a reference for combined heat and power system short-term operation

Experimental study of main rotor/tail rotor/airframe interactions in hover. Volume 1: Text and figures

NASA Technical Reports Server (NTRS)

Balch, D. T.; Saccullo, A.; Sheehy, T. W.

1983-01-01

To assist in identifying and quantifying the relevant parameters associated with the complex topic of main rotor/fuselage/tail rotor interference, a model scale hover test was conducted in the Model Rotor Hover Facility. The test was conducted using the basic model test rig, fuselage skins to represent a UH-60A BLACK HAWK helicopter, 4 sets of rotor blades of varying geometry (i.e., twist, airfoils and solidity) and a model tail rotor that could be relocated to give changes in rotor clearance (axially, laterally, and vertically), can't angle and operating model (pusher or tractor). The description of the models and the tests, data analysis and summary (including plots) are included. The customary system of units gas used for principal measurements and calculations. Expressions in both SI units and customary units are used with the SI units stated first and the customary units afterwords, in parenthesis.

Analysis of integrated photovoltaic-thermal systems using solar concentrators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusoff, M.B.

1983-01-01

An integrated photovoltaic-thermal system using solar concentrators utilizes the solar radiation spectrum in the production of electrical and thermal energy. The electrical conversion efficiency of this system decreases with increasing solar cell temperature. Since a high operating temperature is desirable to maximize the quality of thermal output of the planned integrated system, a proper choice of the operating temperature for the unit cell is of vital importance. The analysis predicts performance characteristics of the unit cell by considering the dependence of the heat generation, the heat absorption and the heat transmission on the material properties of the unit cell structure.more » An analytical model has been developed to describe the heat transport phenomena occurring in the unit cell structure. The range of applicability of the one-dimensional and the two-dimensional models, which have closed-form solutions, has been demonstrated. Parametric and design studies point out the requirements for necessary good electrical and thermal performance. A procedure utilizing functional forms of component characteristics in the form of partial coefficients of the dependent variable has been developed to design and operate the integrated system to have a desirable value of the thermal to electrical output ratio both at design and operating modes.« less

Improving Power System Modeling. A Tool to Link Capacity Expansion and Production Cost Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diakov, Victor; Cole, Wesley; Sullivan, Patrick

2015-11-01

Capacity expansion models (CEM) provide a high-level long-term view at the prospects of the evolving power system. In simulating the possibilities of long-term capacity expansion, it is important to maintain the viability of power system operation in the short-term (daily, hourly and sub-hourly) scales. Production-cost models (PCM) simulate routine power system operation on these shorter time scales using detailed load, transmission and generation fleet data by minimizing production costs and following reliability requirements. When based on CEM 'predictions' about generating unit retirements and buildup, PCM provide more detailed simulation for the short-term system operation and, consequently, may confirm the validitymore » of capacity expansion predictions. Further, production cost model simulations of a system that is based on capacity expansion model solution are 'evolutionary' sound: the generator mix is the result of logical sequence of unit retirement and buildup resulting from policy and incentives. The above has motivated us to bridge CEM with PCM by building a capacity expansion - to - production cost model Linking Tool (CEPCoLT). The Linking Tool is built to onset capacity expansion model prescriptions onto production cost model inputs. NREL's ReEDS and Energy Examplar's PLEXOS are the capacity expansion and the production cost models, respectively. Via the Linking Tool, PLEXOS provides details of operation for the regionally-defined ReEDS scenarios.« less

Scheduling elective surgeries: the tradeoff among bed capacity, waiting patients and operating room utilization using goal programming.

PubMed

Li, Xiangyong; Rafaliya, N; Baki, M Fazle; Chaouch, Ben A

2017-03-01

Scheduling of surgeries in the operating rooms under limited competing resources such as surgical and nursing staff, anesthesiologist, medical equipment, and recovery beds in surgical wards is a complicated process. A well-designed schedule should be concerned with the welfare of the entire system by allocating the available resources in an efficient and effective manner. In this paper, we develop an integer linear programming model in a manner useful for multiple goals for optimally scheduling elective surgeries based on the availability of surgeons and operating rooms over a time horizon. In particular, the model is concerned with the minimization of the following important goals: (1) the anticipated number of patients waiting for service; (2) the underutilization of operating room time; (3) the maximum expected number of patients in the recovery unit; and (4) the expected range (the difference between maximum and minimum expected number) of patients in the recovery unit. We develop two goal programming (GP) models: lexicographic GP model and weighted GP model. The lexicographic GP model schedules operating rooms when various preemptive priority levels are given to these four goals. A numerical study is conducted to illustrate the optimal master-surgery schedule obtained from the models. The numerical results demonstrate that when the available number of surgeons and operating rooms is known without error over the planning horizon, the proposed models can produce good schedules and priority levels and preference weights of four goals affect the resulting schedules. The results quantify the tradeoffs that must take place as the preemptive-weights of the four goals are changed.

Skylab extravehicular mobility unit thermal simulator

NASA Technical Reports Server (NTRS)

Hixon, C. W.; Phillips, M. A.

1974-01-01

The analytical methods, thermal model, and user's instructions for the Skylab Extravehicular Mobility Unit (SEMU) routine are presented. This digital computer program was developed for detailed thermal performance predictions of the SEMU on the NASA-JSC Univac 1108 computer system. It accounts for conductive, convective, and radiant heat transfer as well as fluid flow and special component characterization. The program provides thermal performance predictions for a 967 node thermal model in one thirty-sixth (1/36) of mission time when operated at a calculating interval of three minutes (mission time). The program has the operational flexibility to: (1) accept card or magnetic tape data input for the thermal model describing the SEMU structure, fluid systems, crewman and component performance, (2) accept card and/or magnetic tape input of internally generated heat and heat influx from the space environment, and (3) output tabular or plotted histories of temperature, flow rates, and other parameters describing system operating modes.

Joint Intelligence Operations Center (JIOC) Baseline Business Process Model & Capabilities Evaluation Methodology

DTIC Science & Technology

2012-03-01

Targeting Review Board OPLAN Operations Plan OPORD Operations Order OPSIT Operational Situation OSINT Open Source Intelligence OV...Analysis Evaluate FLTREPs MISREPs Unit Assign Assets Feedback Asset Shortfalls Multi-Int Collection Political & Embasy Law Enforcement HUMINT OSINT ...Embassy Information OSINT Manage Theater HUMINT Law Enforcement Collection Sort Requests Platform Information Agency Information M-I Collect

Model-Driven Energy Intelligence

DTIC Science & Technology

2015-03-01

building information model ( BIM ) for operations...estimate of the potential impact on energy performance at Fort Jackson. 15. SUBJECT TERMS Building Information Modeling ( BIM ), Energy, ECMs, monitoring...dimensional AHU Air Handling Unit API Application Programming Interface BIM building information model BLCC Building Life Cycle Cost

Advanced Stirling Radioisotope Generator Thermal Power Model in Thermal Desktop SINDA/FLUINT Analyzer

NASA Technical Reports Server (NTRS)

Wang, Xiao-Yen; Fabanich, William A.; Schmitz, Paul C.

2012-01-01

This paper presents a three-dimensional Advanced Stirling Radioisotope Generator (ASRG) thermal power model that was built using the Thermal Desktop SINDA/FLUINT thermal analyzer. The model was correlated with ASRG engineering unit (EU) test data and ASRG flight unit predictions from Lockheed Martin's Ideas TMG thermal model. ASRG performance under (1) ASC hot-end temperatures, (2) ambient temperatures, and (3) years of mission for the general purpose heat source fuel decay was predicted using this model for the flight unit. The results were compared with those reported by Lockheed Martin and showed good agreement. In addition, the model was used to study the performance of the ASRG flight unit for operations on the ground and on the surface of Titan, and the concept of using gold film to reduce thermal loss through insulation was investigated.

40 CFR Appendix E to Part 63 - Monitoring Procedure for Nonthoroughly Mixed Open Biological Treatment Systems at Kraft Pulp...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... II. Definitions Biological treatment unit = wastewater treatment unit designed and operated to... last zone in the series and ending with the first zone. B. Data Collection Requirements This method is based upon modeling the nonthoroughly mixed open biological treatment unit as a series of well-mixed...

Using bioprocess stoichiometry to build a plant-wide mass balance based steady-state WWTP model.

PubMed

Ekama, G A

2009-05-01

Steady-state models are useful for design of wastewater treatment plants (WWTPs) because they allow reactor sizes and interconnecting flows to be simply determined from explicit equations in terms of unit operation performance criteria. Once the overall WWTP scheme is established and the main system defining parameters of the individual unit operations estimated, dynamic models can be applied to the connected unit operations to refine their design and evaluate their performance under dynamic flow and load conditions. To model anaerobic digestion (AD) within plant-wide WWTP models, not only COD and nitrogen (N) but also carbon (C) fluxes entering the AD need to be defined. Current plant-wide models, like benchmark simulation model No 2 (BSM2), impose a C flux at the AD influent. In this paper, the COD and N mass balance steady-state models of activated sludge (AS) organics degradation, nitrification and denitrification (ND) and anaerobic (AD) and aerobic (AerD) digestion of wastewater sludge are extended and linked with bioprocess transformation stoichiometry to form C, H, O, N, chemical oxygen demand (COD) and charge mass balance based models so that also C (and H and O) can be tracked through the whole WWTP. By assigning a stoichiometric composition (x, y, z and a in C(x)H(y)O(z)N(a)) to each of the five main influent wastewater organic fractions and ammonia, these, and the products generated from them via the biological processes, are tracked through the WWTP. The model is applied to two theoretical case study WWTPs treating the same raw wastewater (WW) to the same final sludge residual biodegradable COD. It is demonstrated that much useful information can be generated with the relatively simple steady-state models to aid WWTP layout design and track the different products exiting the WWTP via the solid, liquid and gas streams, such as aerobic versus anaerobic digestion of waste activated sludge, N loads in recycle streams, methane production for energy recovery and green house gas (CO(2), CH(4)) generation. To reduce trial and error usage of WWTP simulation software, it is recommended that they are extended to include pre-processors based on mass balance steady-state models to assist with WWTP layout design, unit operation selection, reactor sizing, option evaluation and comparison and wastewater characterization before dynamic simulation.

40 CFR Table 3 to Subpart Ffff of... - Model Rule-Operating Limits for Incinerators and Wet Scrubbers

Code of Federal Regulations, 2010 CFR

2010-07-01

... Incinerators and Wet Scrubbers 3 Table 3 to Subpart FFFF of Part 60 Protection of Environment ENVIRONMENTAL...—Model Rule—Operating Limits for Incinerators and Wet Scrubbers As stated in § 60.3023, you must comply... units. a 2. Pressure drop across the wet scrubber or amperage to wet scrubber Minimum pressure drop or...

40 CFR Table 3 to Subpart Ffff of... - Model Rule-Operating Limits for Incinerators and Wet Scrubbers

Code of Federal Regulations, 2011 CFR

2011-07-01

... Incinerators and Wet Scrubbers 3 Table 3 to Subpart FFFF of Part 60 Protection of Environment ENVIRONMENTAL...—Model Rule—Operating Limits for Incinerators and Wet Scrubbers As stated in § 60.3023, you must comply... units. a 2. Pressure drop across the wet scrubber or amperage to wet scrubber Minimum pressure drop or...

Modelling physiological deterioration in post-operative patient vital-sign data.

PubMed

Pimentel, Marco A F; Clifton, David A; Clifton, Lei; Watkinson, Peter J; Tarassenko, Lionel

2013-08-01

Patients who undergo upper-gastrointestinal surgery have a high incidence of post-operative complications, often requiring admission to the intensive care unit several days after surgery. A dataset comprising observational vital-sign data from 171 post-operative patients taking part in a two-phase clinical trial at the Oxford Cancer Centre, was used to explore the trajectory of patients' vital-sign changes during their stay in the post-operative ward using both univariate and multivariate analyses. A model of normality based vital-sign data from patients who had a "normal" recovery was constructed using a kernel density estimate, and tested with "abnormal" data from patients who deteriorated sufficiently to be re-admitted to the intensive care unit. The vital-sign distributions from "normal" patients were found to vary over time from admission to the post-operative ward to their discharge home, but no significant changes in their distributions were observed from halfway through their stay on the ward to the time of discharge. The model of normality identified patient deterioration when tested with unseen "abnormal" data, suggesting that such techniques may be used to provide early warning of adverse physiological events.

A mission-based productivity compensation model for an academic anesthesiology department.

PubMed

Reich, David L; Galati, Maria; Krol, Marina; Bodian, Carol A; Kahn, Ronald A

2008-12-01

We replaced a nearly fixed-salary academic physician compensation model with a mission-based productivity model with the goal of improving attending anesthesiologist productivity. The base salary system was stratified according to rank and clinical experience. The supplemental pay structure was linked to electronic patient records and a scheduling database to award points for clinical activity; educational, research, and administrative points systems were constructed in parallel. We analyzed monthly American Society of Anesthesiologist (ASA) unit data for operating room activity and physician compensation from 2000 through mid-2007, excluding the 1-yr implementation period (July 2004-June 2005) for the new model. Comparing 2005-2006 with 2000-2004, quarterly ASA units increased by 14% (P = 0.0001) and quarterly ASA units per full-time equivalent increased by 31% (P < 0.0001), while quarterly ASA units per anesthetizing location decreased by 10% (P = 0.046). Compared with a baseline year (2001), Instructor and Assistant Professor faculty compensation increased more than Associate Professor and Professor faculty (P < 0.001) in both pre- and postimplementation periods. There were larger compensation increases for the postimplementation period compared with preimplementation across faculty rank groupings (P < 0.0001). Academic and educational output was stable. Implementing a productivity-based faculty compensation model in an academic department was associated with increased mean supplemental pay with relatively fewer faculty. ASA units per month and ASA units per operating room full-time equivalent increased, and these metrics are the most likely drivers of the increased compensation. This occurred despite a slight decrease in clinical productivity as measured by ASA units per anesthetizing location. Academic and educational output was stable.

Unified Deep Learning Architecture for Modeling Biology Sequence.

PubMed

Wu, Hongjie; Cao, Chengyuan; Xia, Xiaoyan; Lu, Qiang

2017-10-09

Prediction of the spatial structure or function of biological macromolecules based on their sequence remains an important challenge in bioinformatics. When modeling biological sequences using traditional sequencing models, characteristics, such as long-range interactions between basic units, the complicated and variable output of labeled structures, and the variable length of biological sequences, usually lead to different solutions on a case-by-case basis. This study proposed the use of bidirectional recurrent neural networks based on long short-term memory or a gated recurrent unit to capture long-range interactions by designing the optional reshape operator to adapt to the diversity of the output labels and implementing a training algorithm to support the training of sequence models capable of processing variable-length sequences. Additionally, the merge and pooling operators enhanced the ability to capture short-range interactions between basic units of biological sequences. The proposed deep-learning model and its training algorithm might be capable of solving currently known biological sequence-modeling problems through the use of a unified framework. We validated our model on one of the most difficult biological sequence-modeling problems currently known, with our results indicating the ability of the model to obtain predictions of protein residue interactions that exceeded the accuracy of current popular approaches by 10% based on multiple benchmarks.

Opportunities for Breakthroughs in Large-Scale Computational Simulation and Design

NASA Technical Reports Server (NTRS)

Alexandrov, Natalia; Alter, Stephen J.; Atkins, Harold L.; Bey, Kim S.; Bibb, Karen L.; Biedron, Robert T.; Carpenter, Mark H.; Cheatwood, F. McNeil; Drummond, Philip J.; Gnoffo, Peter A.

2002-01-01

Opportunities for breakthroughs in the large-scale computational simulation and design of aerospace vehicles are presented. Computational fluid dynamics tools to be used within multidisciplinary analysis and design methods are emphasized. The opportunities stem from speedups and robustness improvements in the underlying unit operations associated with simulation (geometry modeling, grid generation, physical modeling, analysis, etc.). Further, an improved programming environment can synergistically integrate these unit operations to leverage the gains. The speedups result from reducing the problem setup time through geometry modeling and grid generation operations, and reducing the solution time through the operation counts associated with solving the discretized equations to a sufficient accuracy. The opportunities are addressed only at a general level here, but an extensive list of references containing further details is included. The opportunities discussed are being addressed through the Fast Adaptive Aerospace Tools (FAAST) element of the Advanced Systems Concept to Test (ASCoT) and the third Generation Reusable Launch Vehicles (RLV) projects at NASA Langley Research Center. The overall goal is to enable greater inroads into the design process with large-scale simulations.

AN OPERATIONAL EVALUATION OF THE ETA - CMAQ AIR QUALITY FORECAST MODEL

EPA Science Inventory

The National Oceanic and Atmospheric Administration (NOAA), in partnership with the United States Environmental Protection Agency (EPA), are developing an operational, nationwide Air Quality Forecasting (AQF) system. An experimental phase of this program, which couples NOAA's Et...

The Dynamic General Vegetation Model MC1 over the United States and Canada at a 5-arcminute resolution: model inputs and outputs

Treesearch

Ray Drapek; John B. Kim; Ronald P. Neilson

2015-01-01

Land managers need to include climate change in their decisionmaking, but the climate models that project future climates operate at spatial scales that are too coarse to be of direct use. To create a dataset more useful to managers, soil and historical climate were assembled for the United States and Canada at a 5-arcminute grid resolution. Nine CMIP3 future climate...

Linear control of a boiler-turbine unit: analysis and design.

PubMed

Tan, Wen; Fang, Fang; Tian, Liang; Fu, Caifen; Liu, Jizhen

2008-04-01

Linear control of a boiler-turbine unit is discussed in this paper. Based on the nonlinear model of the unit, this paper analyzes the nonlinearity of the unit, and selects the appropriate operating points so that the linear controller can achieve wide-range performance. Simulation and experimental results at the No. 4 Unit at the Dalate Power Plant show that the linear controller can achieve the desired performance under a specific range of load variations.

Incorporating operational flexibility into electric generation planning Impacts and methods for system design and policy analysis

NASA Astrophysics Data System (ADS)

Palmintier, Bryan S.

This dissertation demonstrates how flexibility in hourly electricity operations can impact long-term planning and analysis for future power systems, particularly those with substantial variable renewables (e.g., wind) or strict carbon policies. Operational flexibility describes a power system's ability to respond to predictable and unexpected changes in generation or demand. Planning and policy models have traditionally not directly captured the technical operating constraints that determine operational flexibility. However, as demonstrated in this dissertation, this capability becomes increasingly important with the greater flexibility required by significant renewables (>= 20%) and the decreased flexibility inherent in some low-carbon generation technologies. Incorporating flexibility can significantly change optimal generation and energy mixes, lower system costs, improve policy impact estimates, and enable system designs capable of meeting strict regulatory targets. Methodologically, this work presents a new clustered formulation that tractably combines a range of normally distinct power system models, from hourly unit-commitment operations to long-term generation planning. This formulation groups similar generators into clusters to reduce problem size, while still retaining the individual unit constraints required to accurately capture operating reserves and other flexibility drivers. In comparisons against traditional unit commitment formulations, errors were generally less than 1% while run times decreased by several orders of magnitude (e.g., 5000x). Extensive numerical simulations, using a realistic Texas-based power system show that ignoring flexibility can underestimate carbon emissions by 50% or result in significant load and wind shedding to meet environmental regulations. Contributions of this dissertation include: 1. Demonstrating that operational flexibility can have an important impact on power system planning, and describing when and how these impacts occur; 2. Demonstrating that a failure to account for operational flexibility can result in undesirable outcomes for both utility planners and policy analysts; and 3. Extending the state of the art for electric power system models by introducing a tractable method for incorporating unit commitment based operational flexibility at full 876o hourly resolution directly into planning optimization. Together these results encourage and offer a new flexibility-aware approach for capacity planning and accompanying policy design that can enable cleaner, less expensive electric power systems for the future. (Copies available exclusively from MIT Libraries, libraries.mit.edu/docs - docs mit.edu)

Space Station Cathode Design, Performance, and Operating Specifications

NASA Technical Reports Server (NTRS)

Patterson, Michael J.; Verhey, Timothy R.; Soulas, George; Zakany, James

1998-01-01

A plasma contactor system was baselined for the International Space Station (ISS) to eliminate/mitigate damaging interactions with the space environment. The system represents a dual-use technology which is a direct outgrowth of the NASA electric propulsion program and, in particular, the technology development efforts on ion thruster systems. The plasma contactor includes a hollow cathode assembly (HCA), a power electronics unit, and a xenon gas feed system. Under a pre-flight development program, these subsystems were taken to the level of maturity appropriate for transfer to U.S. industry for final development. NASA's Lewis Research Center was subsequently requested by ISS to manufacture and deliver the engineering model, qualification model, and flight HCA units. To date, multiple units have been built. One cathode has demonstrated approximately 28,000 hours lifetime, two development unit HCAs have demonstrated over 10,000 hours lifetime, and one development unit HCA has demonstrated more than 32,000 ignitions. All 8 flight HCAs have been manufactured, acceptance tested, and are ready for delivery to the flight contractor. This paper discusses the requirements, mechanical design, performance, operating specifications, and schedule for the plasma contactor flight HCAs.

Review Team Focused Modeling Analysis of Radial Collector Well Operation on the Hypersaline Groundwater Plume beneath the Turkey Point Site near Homestead, Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oostrom, Martinus; Vail, Lance W.

Researchers at Pacific Northwest National Laboratory served as members of a U.S. Nuclear Regulatory Commission review team for the Florida Power & Light Company’s application for two combined construction permits and operating licenses (combined licenses or COLs) for two proposed new reactor units—Turkey Point Units 6 and 7. The review team evaluated the environmental impacts of the proposed action based on the October 29, 2014 revision of the COL application, including the Environmental Report, responses to requests for additional information, and supplemental information. As part of this effort, team members tasked with assessing the environmental effects of proposed construction andmore » operation of Units 6 and 7 at the Turkey Point site reviewed two separate modeling studies that analyzed the interaction between surface water and groundwater that would be altered by the operation of radial collector wells (RCWs) at the site. To further confirm their understanding of the groundwater hydrodynamics and to consider whether certain actions, proposed after the two earlier modeling studies were completed, would alter the earlier conclusions documented by the review team in their draft environmental impact statement (EIS; NRC 2015), a third modeling analysis was performed. The third modeling analysis is discussed in this report.« less

Thermal Modeling and Management of Solid Oxide Fuel Cells Operating with Internally Reformed Methane

NASA Astrophysics Data System (ADS)

Wu, Yiyang; Shi, Yixiang; Cai, Ningsheng; Ni, Meng

2018-06-01

A detailed three-dimensional mechanistic model of a large-scale solid oxide fuel cell (SOFC) unit running on partially pre-reformed methane is developed. The model considers the coupling effects of chemical and electrochemical reactions, mass transport, momentum and heat transfer in the SOFC unit. After model validation, parametric simulations are conducted to investigate how the methane pre-reforming ratio affects the transport and electrochemistry of the SOFC unit. It is found that the methane steam reforming reaction has a "smoothing effect", which can achieve more uniform distributions of gas compositions, current density and temperature among the cell plane. In the case of 1500 W/m2 power density output, adding 20% methane absorbs 50% of internal heat production inside the cell, reduces the maximum temperature difference inside the cell from 70 K to 22 K and reduces the cathode air supply by 75%, compared to the condition of completely pre-reforming of methane. Under specific operating conditions, the pre-reforming ratio of methane has an optimal range for obtaining a good temperature distribution and good cell performance.

Asymptotic formula for the Riesz means of the spectral functions of Laplace-Beltrami operator on unit sphere

NASA Astrophysics Data System (ADS)

Fadly Nurullah Rasedee, Ahmad; Ahmedov, Anvarjon; Sathar, Mohammad Hasan Abdul

2017-09-01

The mathematical models of the heat and mass transfer processes on the ball type solids can be solved using the theory of convergence of Fourier-Laplace series on unit sphere. Many interesting models have divergent Fourier-Laplace series, which can be made convergent by introducing Riesz and Cesaro means of the series. Partial sums of the Fourier-Laplace series summed by Riesz method are integral operators with the kernel known as Riesz means of the spectral function. In order to obtain the convergence results for the partial sums by Riesz means we need to know an asymptotic behavior of the latter kernel. In this work the estimations for Riesz means of spectral function of Laplace-Beltrami operator which guarantees the convergence of the Fourier-Laplace series by Riesz method are obtained.

First flight test results of the Simplified Aid For EVA Rescue (SAFER) propulsion unit

NASA Technical Reports Server (NTRS)

Meade, Carl J.

1995-01-01

The Simplified Aid for EVA Rescue (SAFER) is a small, self-contained, propulsive-backpack system that provides free-flying mobility for an astronaut engaged in a space walk, also known as extravehicular activity (EVA.) SAFER contains no redundant systems and is intended for contingency use only. In essence, it is a small, simplified version of the Manned Maneuvering Unit (MMU) last flown aboard the Space Shuttle in 1985. The operational SAFER unit will only be used to return an adrift EVA astronaut to the spacecraft. Currently, if an EVA crew member inadvertently becomes separated from the Space Shuttle, the Orbiter will maneuver to within the crew member's reach envelope, allowing the astronaut to regain contact with the Orbiter. However, with the advent of operations aboard the Russian MIR Space Station and the International Space Station, the Space Shuttle will not be available to effect a timely rescue. Under these conditions, a SAFER unit would be worn by each EVA crew member. Flight test of the pre-production model of SAFER occurred in September 1994. The crew of Space Shuttle Mission STS-64 flew a 6.9 hour test flight which included performance, flying qualities, systems, and operational utility evaluations. We found that the unit offers adequate propellant and control authority to stabilize and enable the return of a tumbling/separating crew member. With certain modifications, production model of SAFER can provide self-rescue capability to a separated crew member. This paper will present the program background, explain the flight test results and provide some insight into the complex operations of flight test in space.

A simplified economic filter for open-pit gold-silver mining in the United States

USGS Publications Warehouse

Singer, Donald A.; Menzie, W. David; Long, Keith R.

1998-01-01

In resource assessments of undiscovered mineral deposits and in the early stages of exploration, including planning, a need for prefeasibility cost models exists. In exploration, these models to filter economic from uneconomic deposits help to focus on targets that can really benefit the exploration enterprise. In resource assessment, these models can be used to eliminate deposits that would probably be uneconomic even if discovered. The U. S. Bureau of Mines (USBM) previously developed simplified cost models for such problems (Camm, 1991). These cost models estimate operating and capital expenditures for a mineral deposit given its tonnage, grade, and depth. These cost models were also incorporated in USBM prefeasibility software (Smith, 1991). Because the cost data used to estimate operating and capital costs in these models are now over ten years old, we decided that it was necessary to test these equations with more current data. We limited this study to open-pit gold-silver mines located in the United States.

Economic analysis and assessment of syngas production using a modeling approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Hakkwan; Parajuli, Prem B.; Yu, Fei

Economic analysis and modeling are essential and important issues for the development of current feedstock and process technology for bio-gasification. The objective of this study was to develop an economic model and apply to predict the unit cost of syngas production from a micro-scale bio-gasification facility. An economic model was programmed in C++ computer programming language and developed using a parametric cost approach, which included processes to calculate the total capital costs and the total operating costs. The model used measured economic data from the bio-gasification facility at Mississippi State University. The modeling results showed that the unit cost ofmore » syngas production was $1.217 for a 60 Nm-3 h-1 capacity bio-gasifier. The operating cost was the major part of the total production cost. The equipment purchase cost and the labor cost were the largest part of the total capital cost and the total operating cost, respectively. Sensitivity analysis indicated that labor costs rank the top as followed by equipment cost, loan life, feedstock cost, interest rate, utility cost, and waste treatment cost. The unit cost of syngas production increased with the increase of all parameters with exception of loan life. The annual cost regarding equipment, labor, feedstock, waste treatment, and utility cost showed a linear relationship with percent changes, while loan life and annual interest rate showed a non-linear relationship. This study provides the useful information for economic analysis and assessment of the syngas production using a modeling approach.« less

An Approach to Operational Analysis: Doctrinal Task Decomposition

DTIC Science & Technology

2016-08-04

Once the unit is selected , CATS will output all of the doctrinal collective tasks associated with the unit. Currently, CATS outputs this information...Army unit are controlled data items, but for explanation purposes consider this simple example using a restaurant as the unit of interest. Table 1...shows an example Task Model for a restaurant using language and format similar to what CATS provides. Only 3 levels are shown in the example, but

The Poisson Random Process. Applications of Probability Theory to Operations Research. Modules and Monographs in Undergraduate Mathematics and Its Applications Project. UMAP Unit 340.

ERIC Educational Resources Information Center

Wilde, Carroll O.

The Poisson probability distribution is seen to provide a mathematical model from which useful information can be obtained in practical applications. The distribution and some situations to which it applies are studied, and ways to find answers to practical questions are noted. The unit includes exercises and a model exam, and provides answers to…

Evaluation of Military Field-Water Quality. Volume 8. Performance of Mobile Water-Purification Unit (MWPU) and Pretreatment Components of the 600-GPH Reverse Osmosis Water Purification Unit (ROWPU), and Consideration of Reverse Osmosis (RO) Bypass, Potable-Water Disinfection, and Water-Quality Analysis Techniques

DTIC Science & Technology

1990-05-01

Health Risks in Potential Theaters of Operation for U.S. Military Forces. The nine volumes of this study contain a comprehensive assessment of the chemical...module. The percentage of total free chlorine ( hypochlorous acid , HOCl) plus hypochlorlte ion (OClN), measured by the Model 453 membrane sensor, varies...between the performances of the 600-Sph Reverse Osmosis Water Purification Unit (ROWPU) operated in the bypass node and ’the Mobile Water Purification

Economics of food irradiation

NASA Astrophysics Data System (ADS)

Kunstadt, Peter; Eng, P.; Steeves, Colyn; Beaulieu, Daniel; Eng, P.

1993-07-01

The number of products being radiation processed worldwide is constantly increasing and today includes such diverse items as medical disposables, fruits and vegetables, spices, meats, seafoods and waste products. This range of products to be processed has resulted in a wide range of irradiator designs and capital and operating cost requirements. This paper discusses the economics of low dose food irradiation applications and the effects of various parameters on unit processing costs. It provides a model for calculating specific unit processing costs by correlating known capital costs with annual operating costs and annual throughputs. It is intended to provide the reader with a general knowledge of how unit processing costs are derived.

Modeling for Military Operational Medicine Scientific and Technical Objectives

DTIC Science & Technology

2005-09-01

measurements and less error in interpreting the measurements since the sensor units are placed directly under armor ; and (3) new material that matches the...more accurate measurements and less error in interpreting the measurements, since the sensor units are placed directly under armor ; and (3) new

Metallurgical Plant Optimization Through the use of Flowsheet Simulation Modelling

NASA Astrophysics Data System (ADS)

Kennedy, Mark William

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Design of experiments applications in bioprocessing: concepts and approach.

PubMed

Kumar, Vijesh; Bhalla, Akriti; Rathore, Anurag S

2014-01-01

Most biotechnology unit operations are complex in nature with numerous process variables, feed material attributes, and raw material attributes that can have significant impact on the performance of the process. Design of experiments (DOE)-based approach offers a solution to this conundrum and allows for an efficient estimation of the main effects and the interactions with minimal number of experiments. Numerous publications illustrate application of DOE towards development of different bioprocessing unit operations. However, a systematic approach for evaluation of the different DOE designs and for choosing the optimal design for a given application has not been published yet. Through this work we have compared the I-optimal and D-optimal designs to the commonly used central composite and Box-Behnken designs for bioprocess applications. A systematic methodology is proposed for construction of the model and for precise prediction of the responses for the three case studies involving some of the commonly used unit operations in downstream processing. Use of Akaike information criterion for model selection has been examined and found to be suitable for the applications under consideration. © 2013 American Institute of Chemical Engineers.

Modeling of selected ceramic processing parameters employed in the fabrication of 238PuO 2 fuel pellets

DOE PAGES

Brockman, R. A.; Kramer, D. P.; Barklay, C. D.; ...

2011-10-01

Recent deep space missions utilize the thermal output of the radioisotope plutonium-238 as the fuel in the thermal to electrical power system. Since the application of plutonium in its elemental state has several disadvantages, the fuel employed in these deep space power systems is typically in the oxide form such as plutonium-238 dioxide ( 238PuO 2). As an oxide, the processing of the plutonium dioxide into fuel pellets is performed via ''classical'' ceramic processing unit operations such as sieving of the powder, pressing, sintering, etc. Modeling of these unit operations can be beneficial in the understanding and control of processingmore » parameters with the goal of further enhancing the desired characteristics of the 238PuO 2 fuel pellets. A finite element model has been used to help identify the time-temperature-stress profile within a pellet during a furnace operation taking into account that 238PuO 2 itself has a significant thermal output. The results of the modeling efforts will be discussed.« less

Modeling of the radiation belt megnetosphere in decisional timeframes

DOEpatents

Koller, Josef; Reeves, Geoffrey D; Friedel, Reiner H.W.

2013-04-23

Systems and methods for calculating L* in the magnetosphere with essentially the same accuracy as with a physics based model at many times the speed by developing a surrogate trained to be a surrogate for the physics-based model. The trained model can then beneficially process input data falling within the training range of the surrogate model. The surrogate model can be a feedforward neural network and the physics-based model can be the TSK03 model. Operatively, the surrogate model can use parameters on which the physics-based model was based, and/or spatial data for the location where L* is to be calculated. Surrogate models should be provided for each of a plurality of pitch angles. Accordingly, a surrogate model having a closed drift shell can be used from the plurality of models. The feedforward neural network can have a plurality of input-layer units, there being at least one input-layer unit for each physics-based model parameter, a plurality of hidden layer units and at least one output unit for the value of L*.

Modeling and Economic Analysis of Power Grid Operations in a Water Constrained System

NASA Astrophysics Data System (ADS)

Zhou, Z.; Xia, Y.; Veselka, T.; Yan, E.; Betrie, G.; Qiu, F.

2016-12-01

The power sector is the largest water user in the United States. Depending on the cooling technology employed at a facility, steam-electric power stations withdrawal and consume large amounts of water for each megawatt hour of electricity generated. The amounts are dependent on many factors, including ambient air and water temperatures, cooling technology, etc. Water demands from most economic sectors are typically highest during summertime. For most systems, this coincides with peak electricity demand and consequently a high demand for thermal power plant cooling water. Supplies however are sometimes limited due to seasonal precipitation fluctuations including sporadic droughts that lead to water scarcity. When this occurs there is an impact on both unit commitments and the real-time dispatch. In this work, we model the cooling efficiency of several different types of thermal power generation technologies as a function of power output level and daily temperature profiles. Unit specific relationships are then integrated in a power grid operational model that minimizes total grid production cost while reliably meeting hourly loads. Grid operation is subject to power plant physical constraints, transmission limitations, water availability and environmental constraints such as power plant water exit temperature limits. The model is applied to a standard IEEE-118 bus system under various water availability scenarios. Results show that water availability has a significant impact on power grid economics.

Leveraging Venture Capital and Commercial Business: Enhancing Stability Operations

DTIC Science & Technology

2011-03-24

Economic Stability Operations have emerged as a new element of United States national strategic power. The creation of jobs, through commercial...examine the key strategic factors influencing long-term economic stability following the withdrawal of combat forces. This paper provides a model for

Scalable Mobile Ad Hoc Network (MANET) to Enhance Situational Awareness in Distributed Small Unit Operations

DTIC Science & Technology

2015-06-01

raspberry pi , robotic operation system (ros), arduino 15. NUMBER OF PAGES 123 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT...51  2.  Raspberry Pi ...52  Figure 21.  The Raspberry Pi B+ model, from [24

A 63 K phase change unit integrating with pulse tube cryocoolers

NASA Astrophysics Data System (ADS)

Chunhui, Kong; Liubiao, Chen; Sixue, Liu; Yuan, Zhou; Junjie, Wang

2017-02-01

This article presents the design and computer model results of an integrated cooler system which consists of a single stage pulse tube cryocooler integrated with a small amount of a phase change material. A cryogenic thermal switch was used to thermally connect the phase change unit to the cold end of the cryocooler. During heat load operation, the cryogenic thermal switch is turned off to avoid vibrations. The phase change unit absorbs heat loads by melting a substance in a constant pressure-temperature-volume process. Once the substance has been melted, the cryogenic thermal turned on, the cryocooler can then refreeze the material. Advantages of this type of cooler are no vibrations during sensor operations; the ability to absorb increased heat loads; potentially longer system lifetime; and a lower mass, volume and cost. A numerical model was constructed from derived thermodynamic relationships for the cooling/heating and freezing/melting processes.

Proposal for a new CAPE-OPEN Object Model

EPA Science Inventory

Process simulation applications require the exchange of significant amounts of data between the flowsheet environment, unit operation model, and thermodynamic server. Packing and unpacking various data types and exchanging data using structured text-based architectures, including...

Establishing and running a trauma and dissociation unit: a contemporary experience.

PubMed

Middleton, Warwick; Higson, David

2004-12-01

To evaluate the functioning of a trauma and dissociation unit that has run for the past 8 years in a private hospital, with particular regard to operating philosophy, operating parameters, challenges encountered, research and educational initiatives, and the applicability of the treatment model to other settings. Despite the challenges associated with significant difficulties in the corporate management of a private health-care system, it has been possible to operate an inpatient and day hospital programme tailored to the needs of patients in the dissociative spectrum, and the lessons learnt from this experience are valid considerations in the future planning of mental health services overall.

LIME SPRAY DRYER FLUE GAS DESULFURIZATION COMPUTER MODEL USERS MANUAL

EPA Science Inventory

The report describes a lime spray dryer/baghouse (FORTRAN) computer model that simulates SO2 removal and permits study of related impacts on design and economics as functions of design parameters and operating conditions for coal-fired electric generating units. The model allows ...

40 CFR 60.3046 - What records must I keep?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model..., malfunctioning, or out of control (except for downtime associated with zero and span and other routine... the types of waste burned during the test. (j) Records showing the names of OSWI unit operators who...

40 CFR 60.3046 - What records must I keep?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model..., malfunctioning, or out of control (except for downtime associated with zero and span and other routine... the types of waste burned during the test. (j) Records showing the names of OSWI unit operators who...

40 CFR 60.3046 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model..., malfunctioning, or out of control (except for downtime associated with zero and span and other routine... the types of waste burned during the test. (j) Records showing the names of OSWI unit operators who...

40 CFR 60.3046 - What records must I keep?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model..., malfunctioning, or out of control (except for downtime associated with zero and span and other routine... the types of waste burned during the test. (j) Records showing the names of OSWI unit operators who...

40 CFR 60.3046 - What records must I keep?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model..., malfunctioning, or out of control (except for downtime associated with zero and span and other routine... the types of waste burned during the test. (j) Records showing the names of OSWI unit operators who...

Development of a geodatabase and conceptual model of the hydrogeologic units beneath air force plant 4 and Naval Air Station-Joint Reserve Base Carswell Field, Fort Worth, Texas

USGS Publications Warehouse

Shah, Sachin D.

2004-01-01

Air Force Plant 4 and adjacent Naval Air Station-Joint Reserve Base Carswell Field at Fort Worth, Texas, constitute a government-owned, contractor-operated facility that has been in operation since 1942. Contaminants from AFP4, primarily volatile organic compounds and metals, have entered the ground-water-flow system through leakage from waste-disposal sites and from manufacturing processes. The U.S. Geological Survey developed a comprehensive geodatabase of temporal and spatial environmental information associated with the hydrogeologic units (alluvial aquifer, Goodland-Walnut confining unit, and Paluxy aquifer) beneath the facility and a three-dimensional conceptual model of the hydrogeologic units integrally linked to the geodatabase. The geodatabase design uses a thematic layer approach to create layers of feature data using a geographic information system. The various features are separated into relational tables in the geodatabase on the basis of how they interact and correspond to one another. Using the geodatabase, geographic data at the site are manipulated to produce maps, allow interactive queries, and perform spatial analyses. The conceptual model for the study area comprises computer-generated, three-dimensional block diagrams of the hydrogeologic units. The conceptual model provides a platform for visualization of hydrogeologic-unit sections and surfaces and for subsurface environmental analyses. The conceptual model is based on three structural surfaces and two thickness configurations of the study area. The three structural surfaces depict the altitudes of the tops of the three hydrogeologic units. The two thickness configurations are those of the alluvial aquifer and the Goodland-Walnut confining unit. The surface of the alluvial aquifer was created using a U.S. Geological Survey 10-meter digital elevation model. The 2,130 point altitudes of the top of the Goodland-Walnut unit were compiled from lithologic logs from existing wells, available soil-boring logs, and previous studies. Data from 120 wells, primarily from existing reports, were used to create a map of the approximate altitude of the Paluxy aquifer.

HIPPO Unit Commitment Version 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-17

Developed for the Midcontinent Independent System Operator, Inc. (MISO), HIPPO-Unit Commitment Version 1 is for solving security constrained unit commitment problem. The model was developed to solve MISO's cases. This version of codes includes I/O module to read in MISO's csv files, modules to create a state-based mixed integer programming formulation for solving MIP, and modules to test basic procedures to solve MIP via HPC.

40 CFR 75.19 - Optional SO2, NOX, and CO2 emissions calculation for low mass emissions (LME) units.

Code of Federal Regulations, 2010 CFR

2010-07-01

...), manufacturer and model, and must have the same history of modifications (e.g., have the same controls installed... (or group of identical units) equipped with SCR (or SNCR) and uses dry low-NOX technology to control... with add-on NOX emission controls, and for units that use dry low-NOX technology, the owner or operator...

A framework for performance measurement in university using extended network data envelopment analysis (DEA) structures

NASA Astrophysics Data System (ADS)

Kashim, Rosmaini; Kasim, Maznah Mat; Rahman, Rosshairy Abd

2015-12-01

Measuring university performance is essential for efficient allocation and utilization of educational resources. In most of the previous studies, performance measurement in universities emphasized the operational efficiency and resource utilization without investigating the university's ability to fulfill the needs of its stakeholders and society. Therefore, assessment of the performance of university should be separated into two stages namely efficiency and effectiveness. In conventional DEA analysis, a decision making unit (DMU) or in this context, a university is generally treated as a black-box which ignores the operation and interdependence of the internal processes. When this happens, the results obtained would be misleading. Thus, this paper suggest an alternative framework for measuring the overall performance of a university by incorporating both efficiency and effectiveness and applies network DEA model. The network DEA models are recommended because this approach takes into account the interrelationship between the processes of efficiency and effectiveness in the system. This framework also focuses on the university structure which is expanded from the hierarchical to form a series of horizontal relationship between subordinate units by assuming both intermediate unit and its subordinate units can generate output(s). Three conceptual models are proposed to evaluate the performance of a university. An efficiency model is developed at the first stage by using hierarchical network model. It is followed by an effectiveness model which take output(s) from the hierarchical structure at the first stage as a input(s) at the second stage. As a result, a new overall performance model is proposed by combining both efficiency and effectiveness models. Thus, once this overall model is realized and utilized, the university's top management can determine the overall performance of each unit more accurately and systematically. Besides that, the result from the network DEA model can give a superior benchmarking power over the conventional models.

Gas engine heat pump cycle analysis. Volume 1: Model description and generic analysis

NASA Astrophysics Data System (ADS)

Fischer, R. D.

1986-10-01

The task has prepared performance and cost information to assist in evaluating the selection of high voltage alternating current components, values for component design variables, and system configurations and operating strategy. A steady-state computer model for performance simulation of engine-driven and electrically driven heat pumps was prepared and effectively used for parametric and seasonal performance analyses. Parametric analysis showed the effect of variables associated with design of recuperators, brine coils, domestic hot water heat exchanger, compressor size, engine efficiency, insulation on exhaust and brine piping. Seasonal performance data were prepared for residential and commercial units in six cities with system configurations closely related to existing or contemplated hardware of the five GRI engine contractors. Similar data were prepared for an advanced variable-speed electric unit for comparison purposes. The effect of domestic hot water production on operating costs was determined. Four fan-operating strategies and two brine loop configurations were explored.

Application of agent-based system for bioprocess description and process improvement.

PubMed

Gao, Ying; Kipling, Katie; Glassey, Jarka; Willis, Mark; Montague, Gary; Zhou, Yuhong; Titchener-Hooker, Nigel J

2010-01-01

Modeling plays an important role in bioprocess development for design and scale-up. Predictive models can also be used in biopharmaceutical manufacturing to assist decision-making either to maintain process consistency or to identify optimal operating conditions. To predict the whole bioprocess performance, the strong interactions present in a processing sequence must be adequately modeled. Traditionally, bioprocess modeling considers process units separately, which makes it difficult to capture the interactions between units. In this work, a systematic framework is developed to analyze the bioprocesses based on a whole process understanding and considering the interactions between process operations. An agent-based approach is adopted to provide a flexible infrastructure for the necessary integration of process models. This enables the prediction of overall process behavior, which can then be applied during process development or once manufacturing has commenced, in both cases leading to the capacity for fast evaluation of process improvement options. The multi-agent system comprises a process knowledge base, process models, and a group of functional agents. In this system, agent components co-operate with each other in performing their tasks. These include the description of the whole process behavior, evaluating process operating conditions, monitoring of the operating processes, predicting critical process performance, and providing guidance to decision-making when coping with process deviations. During process development, the system can be used to evaluate the design space for process operation. During manufacture, the system can be applied to identify abnormal process operation events and then to provide suggestions as to how best to cope with the deviations. In all cases, the function of the system is to ensure an efficient manufacturing process. The implementation of the agent-based approach is illustrated via selected application scenarios, which demonstrate how such a framework may enable the better integration of process operations by providing a plant-wide process description to facilitate process improvement. Copyright 2009 American Institute of Chemical Engineers

An Economic Model of U.S. Airline Operating Expenses

NASA Technical Reports Server (NTRS)

Harris, Franklin D.

2005-01-01

This report presents a new economic model of operating expenses for 67 airlines. The model is based on data that the airlines reported to the United States Department of Transportation in 1999. The model incorporates expense-estimating equations that capture direct and indirect expenses of both passenger and cargo airlines. The variables and business factors included in the equations are detailed enough to calculate expenses at the flight equipment reporting level. Total operating expenses for a given airline are then obtained by summation over all aircraft operated by the airline. The model's accuracy is demonstrated by correlation with the DOT Form 41 data from which it was derived. Passenger airlines are more accurately modeled than cargo airlines. An appendix presents a concise summary of the expense estimating equations with explanatory notes. The equations include many operational and aircraft variables, which accommodate any changes that airline and aircraft manufacturers might make to lower expenses in the future. In 1999, total operating expenses of the 67 airlines included in this study amounted to slightly over $100.5 billion. The economic model reported herein estimates $109.3 billion.

40 CFR 60.2630 - What should I include in my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Waste Management.... Model Rule—Operator Training and Qualification ...

40 CFR 60.2630 - What should I include in my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Waste Management.... Model Rule—Operator Training and Qualification ...

Ensemble Models

EPA Science Inventory

Ensemble forecasting has been used for operational numerical weather prediction in the United States and Europe since the early 1990s. An ensemble of weather or climate forecasts is used to characterize the two main sources of uncertainty in computer models of physical systems: ...

A Mercury Model of Atmospheric Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christensen, Alex B.; Chodash, Perry A.; Procassini, R. J.

Using the particle transport code Mercury, accurate models were built of the two sources used in Operation BREN, a series of radiation experiments performed by the United States during the 1960s. In the future, these models will be used to validate Mercury’s ability to simulate atmospheric transport.

Energy consumption and energy-saving potential analysis of pollutant abatement systems in a 1000MW coal-fired power plant.

PubMed

Yang, Hang; Zhang, Yongxin; Zheng, Chenghang; Wu, Xuecheng; Chen, Linghong; Gao, Xiang; Fu, Joshua S

2018-05-10

The pollutant abatement systems are widely applied in the coal-fired power sector and the energy consumption was considered an important part of the auxiliary power. An energy consumption analysis and assessment model of pollutant abatement systems in a power unit was developed based on the dynamic parameters and technology. The energy consumption of pollutant abatement systems in a 1000 MW coal-fired power unit which meet the ultra-low emission limits and the factors of operating parameters including unit load and inlet concentration of pollutants on the operating power were analyzed. The results show that the total power consumption of the pollutant abatement systems accounted for 1.27% of the gross power generation during the monitoring period. The WFGD system consumed 67% of the rate while the SCR and ESP systems consumed 8.9% and 24.1%. The power consumption rate of pollutant abatement systems decreased with the increase of unit load and increased with the increase of the inlet concentration of pollutants. The operation adjustment was also an effective method to increase the energy efficiency. For example, the operation adjustment of slurry circulation pumps could promote the energy-saving operation of WFGD system. Implication Statement The application of pollutant abatement technologies increases the internal energy consumption of the power plant, which will lead to an increase of power generation costs. The real-time energy consumption of the different pollutant abatement systems in a typical power unit is analyzed based on the dynamic operating data. Further, the influence of different operating parameters on the operating power of the system and the possible energy-saving potential are analyzed.

Thermo-physical performance prediction of the KSC Ground Operation Demonstration Unit for liquid hydrogen

NASA Astrophysics Data System (ADS)

Baik, J. H.; Notardonato, W. U.; Karng, S. W.; Oh, I.

2015-12-01

NASA Kennedy Space Center (KSC) researchers have been working on enhanced and modernized cryogenic liquid propellant handling techniques to reduce life cycle costs of propellant management system for the unique KSC application. The KSC Ground Operation Demonstration Unit (GODU) for liquid hydrogen (LH2) plans to demonstrate integrated refrigeration, zero-loss flexible term storage of LH2, and densified hydrogen handling techniques. The Florida Solar Energy Center (FSEC) has partnered with the KSC researchers to develop thermal performance prediction model of the GODU for LH2. The model includes integrated refrigeration cooling performance, thermal losses in the tank and distribution lines, transient system characteristics during chilling and loading, and long term steady-state propellant storage. This paper will discuss recent experimental data of the GODU for LH2 system and modeling results.

Simulation of load-sharing in standalone distributed generation system

NASA Astrophysics Data System (ADS)

Ajewole, Titus O.; Craven, Robert P. M.; Kayode, Olakunle; Babalola, Olufisayo S.

2018-05-01

This paper presents a study on load-sharing among the component generating units of a multi-source electric microgrid that is operated as an autonomous ac supply-mode system. Emerging trend in power system development permits deployment of microgrids for standalone or stand-by applications, thereby requiring active- and reactive power sharing among the discrete generating units contained in hybrid-source microgrids. In this study, therefore, a laboratory-scale model of a microgrid energized with three renewable energy-based sources is employed as a simulation platform to investigate power sharing among the power-generating units. Each source is represented by a source emulator that captures the real operational characteristics of the mimicked generating unit and, with implementation of real-life weather data and load profiles on the model; the sharing of the load among the generating units is investigated. There is a proportionate generation of power by the three source emulators, with their frequencies perfectly synchronized at the point of common coupling as a result of balance flow of power among them. This hybrid topology of renewable energy-based microgrid could therefore be seamlessly adapted into national energy mix by the indigenous electric utility providers in Nigeria.

40 CFR 60.5225 - What are the monitoring and calibration requirements for compliance with my operating limits?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for compliance with my operating limits? 60.5225 Section 60.5225 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Existing Sewage Sludge Incineration Units Model Rule...

40 CFR 60.2655 - How do I renew my lapsed operator qualification?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...) For a lapse of less than 3 years, you must complete a standard annual refresher course described in...

40 CFR 60.2655 - How do I renew my lapsed operator qualification?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training...) For a lapse of less than 3 years, you must complete a standard annual refresher course described in...

40 CFR 60.5190 - How do I establish my operating limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Times for Existing Sewage Sludge Incineration Units Model Rule-Initial Compliance Requirements § 60.5190..., and cadmium. (4) For an activated carbon injection system designed to control emissions of mercury, you are not required to establish an operating limit and monitor sorbent injection rate and carrier...

40 CFR 60.5190 - How do I establish my operating limits?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Times for Existing Sewage Sludge Incineration Units Model Rule-Initial Compliance Requirements § 60.5190..., and cadmium. (4) For an activated carbon injection system designed to control emissions of mercury, you are not required to establish an operating limit and monitor sorbent injection rate and carrier...

40 CFR 60.5190 - How do I establish my operating limits?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Times for Existing Sewage Sludge Incineration Units Model Rule-Initial Compliance Requirements § 60.5190..., and cadmium. (4) For an activated carbon injection system designed to control emissions of mercury, you are not required to establish an operating limit and monitor sorbent injection rate and carrier...

40 CFR 60.5190 - How do I establish my operating limits?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Times for Existing Sewage Sludge Incineration Units Model Rule-Initial Compliance Requirements § 60.5190..., and cadmium. (4) For an activated carbon injection system designed to control emissions of mercury, you are not required to establish an operating limit and monitor sorbent injection rate and carrier...

24 CFR 990.260 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-04-01

... THE PUBLIC HOUSING OPERATING FUND PROGRAM Asset Management § 990.260 Applicability. (a) PHAs that own... units, are required to operate using an asset management model consistent with this subpart. (b) PHAs... project. However, if a PHA selects this option, it will not receive the add-on for the asset management...

Modeling of the Human - Operator in a Complex System Functioning Under Extreme Conditions

NASA Astrophysics Data System (ADS)

Getzov, Peter; Hubenova, Zoia; Yordanov, Dimitar; Popov, Wiliam

2013-12-01

Problems, related to the explication of sophisticated control systems of objects, operating under extreme conditions, have been examined and the impact of the effectiveness of the operator's activity on the systems as a whole. The necessity of creation of complex simulation models, reflecting operator's activity, is discussed. Organizational and technical system of an unmanned aviation complex is described as a sophisticated ergatic system. Computer realization of main subsystems of algorithmic system of the man as a controlling system is implemented and specialized software for data processing and analysis is developed. An original computer model of a Man as a tracking system has been implemented. Model of unmanned complex for operators training and formation of a mental model in emergency situation, implemented in "matlab-simulink" environment, has been synthesized. As a unit of the control loop, the pilot (operator) is simplified viewed as an autocontrol system consisting of three main interconnected subsystems: sensitive organs (perception sensors); central nervous system; executive organs (muscles of the arms, legs, back). Theoretical-data model of prediction the level of operator's information load in ergatic systems is proposed. It allows the assessment and prediction of the effectiveness of a real working operator. Simulation model of operator's activity in takeoff based on the Petri nets has been synthesized.

Stochastic Multi-Timescale Power System Operations With Variable Wind Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Hongyu; Krad, Ibrahim; Florita, Anthony

This paper describes a novel set of stochastic unit commitment and economic dispatch models that consider stochastic loads and variable generation at multiple operational timescales. The stochastic model includes four distinct stages: stochastic day-ahead security-constrained unit commitment (SCUC), stochastic real-time SCUC, stochastic real-time security-constrained economic dispatch (SCED), and deterministic automatic generation control (AGC). These sub-models are integrated together such that they are continually updated with decisions passed from one to another. The progressive hedging algorithm (PHA) is applied to solve the stochastic models to maintain the computational tractability of the proposed models. Comparative case studies with deterministic approaches are conductedmore » in low wind and high wind penetration scenarios to highlight the advantages of the proposed methodology, one with perfect forecasts and the other with current state-of-the-art but imperfect deterministic forecasts. The effectiveness of the proposed method is evaluated with sensitivity tests using both economic and reliability metrics to provide a broader view of its impact.« less

Active-Reserve Force Cost Model

DTIC Science & Technology

2015-01-01

structure to be maintained for a given level of expenditure. We have developed this methodology and set of associated computer-based tools to...rotational, and deployed units or systems • Attain acceptable steady state operational or presence levels , as measured by the number of units a...at the community level . By community, we mean the set of units of a given type: mission, platform, or capability. We do this because AC-RC force-mix

Development of a Power Electronics Unit for the Space Station Plasma Contactor

NASA Technical Reports Server (NTRS)

Hamley, John A.; Hill, Gerald M.; Patterson, Michael J.; Saggio, Joseph, Jr.; Terdan, Fred; Mansell, Justin D.

1994-01-01

A hollow cathode plasma contactor has been baselined as a charge control device for the Space Station (SS) to prevent deleterious interactions of coated structural components with the ambient plasma. NASA LeRC Work Package 4 initiated the development of a plasma contactor system comprised of a Power Electronics Unit (PEU), an Expellant Management Unit (EMU), a command and data interface, and a Plasma Contactor Unit (PCU). A breadboard PEU was designed and fabricated. The breadboard PEU contains a cathode heater and discharge power supply, which were required to operate the PCU, a control and auxiliary power converter, an EMU interface, a command and telemetry interface, and a controller. The cathode heater and discharge supplies utilized a push-pull topology with a switching frequency of 20 kHz and pulse-width-modulated (PWM) control. A pulse ignition circuit derived from that used in arcjet power processors was incorporated in the discharge supply for discharge ignition. An 8088 based microcontroller was utilized in the breadboard model to provide a flexible platform for controller development with a simple command/data interface incorporating a direct connection to SS Mulitplexer/Demultiplexer (MDM) analog and digital I/O cards. Incorporating this in the flight model would eliminate the hardware and software overhead associated with a 1553 serial interface. The PEU autonomously operated the plasma contactor based on command inputs and was successfully integrated with a prototype plasma contactor unit demonstrating reliable ignition of the discharge and steady-state operation.

The reliability analysis of a separated, dual fail operational redundant strapdown IMU. [inertial measurement unit

NASA Technical Reports Server (NTRS)

Motyka, P.

1983-01-01

A methodology for quantitatively analyzing the reliability of redundant avionics systems, in general, and the dual, separated Redundant Strapdown Inertial Measurement Unit (RSDIMU), in particular, is presented. The RSDIMU is described and a candidate failure detection and isolation system presented. A Markov reliability model is employed. The operational states of the system are defined and the single-step state transition diagrams discussed. Graphical results, showing the impact of major system parameters on the reliability of the RSDIMU system, are presented and discussed.

U.S. Air Force Operational Medicine: Using the Enterprise Estimating Supplies Program to Develop Materiel Solutions for the Air Force Optometry Augmentation Team (FFDOT)

DTIC Science & Technology

2010-11-09

Report No. 10-13M, supported by the U.S. Air Force Medical Logistics Agency, under Work Unit No. 60334. The views expressed in this article are those...recommended 917Q line list. The Unit Type Code (UTC) capabilities, operational requirements, and materiel solutions were identified, and issues of...by 22%, and cost by 4%, or $9,500. Modeling and simulating a medical system like the FFDOT, with a range of capabilities and functional areas

SIMYAR: a cable-yarding simulation model.

Treesearch

R.J. McGaughey; R.H. Twito

1987-01-01

A skyline-logging simulation model designed to help planners evaluate potential yarding options and alternative harvest plans is presented. The model, called SIMYAR, uses information about the timber stand, yarding equipment, and unit geometry to estimate yarding co stand productivity for a particular operation. The costs of felling, bucking, loading, and hauling are...

Organizing the Counter Terrorism Unit of the Republic of Mauritius: Using the Main Counterterrorism Agencies of the United States of America as Models

DTIC Science & Technology

2011-12-01

organized and equipped along the same lines as the French gendarmerie mobile, while its counter terrorism component is a replica of the French Groupe...first responders involved in disaster relief and homeland defense operations by providing geospatial intelligence data, products, and analyses.125 4...the impact of manmade and natural disasters .126 5. Service Intelligence Units The service intelligence units of the Army, Navy, Air Force, and

Unit mechanisms of fission gas release: Current understanding and future needs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tonks, Michael; Andersson, David; Devanathan, Ram

Gaseous fission product transport and release has a large impact on fuel performance, degrading fuel properties and, once the gas is released into the gap between the fuel and cladding, lowering gap thermal conductivity and increasing gap pressure. While gaseous fission product behavior has been investigated with bulk reactor experiments and simplified analytical models, recent improvements in experimental and modeling approaches at the atomistic and mesoscales are being applied to provide unprecedented understanding of the unit mechanisms that define the fission product behavior. In this article, existing research on the basic mechanisms behind the various stages of fission gas releasemore » during normal reactor operation are summarized and critical areas where experimental and simulation work is needed are identified. This basic understanding of the fission gas behavior mechanisms has the potential to revolutionize our ability to predict fission product behavior during reactor operation and to design fuels that have improved fission product retention. In addition, this work can serve as a model on how a coupled experimental and modeling approach can be applied to understand the unit mechanisms behind other critical behaviors in reactor materials.« less

The United States Special Operations Command Civil Military Engagement Program - A Model for Military-Interagency Low Cost / Small Footprint Activities

DTIC Science & Technology

2014-05-02

Interagency Coordination Centers (JIACs), Interagency Task Forces ( IATFs ) are found within GCCs and subordinate military units in an attempt to bridge...Interagency Tasks Forces ( IATFs ) that exist at each Geographic Combatant Command (GCC). Rather, this chapter serves to highlight the Civil Military

PyMUS: Python-Based Simulation Software for Virtual Experiments on Motor Unit System

PubMed Central

Kim, Hojeong; Kim, Minjung

2018-01-01

We constructed a physiologically plausible computationally efficient model of a motor unit and developed simulation software that allows for integrative investigations of the input–output processing in the motor unit system. The model motor unit was first built by coupling the motoneuron model and muscle unit model to a simplified axon model. To build the motoneuron model, we used a recently reported two-compartment modeling approach that accurately captures the key cell-type-related electrical properties under both passive conditions (somatic input resistance, membrane time constant, and signal attenuation properties between the soma and the dendrites) and active conditions (rheobase current and afterhyperpolarization duration at the soma and plateau behavior at the dendrites). To construct the muscle unit, we used a recently developed muscle modeling approach that reflects the experimentally identified dependencies of muscle activation dynamics on isometric, isokinetic and dynamic variation in muscle length over a full range of stimulation frequencies. Then, we designed the simulation software based on the object-oriented programing paradigm and developed the software using open-source Python language to be fully operational using graphical user interfaces. Using the developed software, separate simulations could be performed for a single motoneuron, muscle unit and motor unit under a wide range of experimental input protocols, and a hierarchical analysis could be performed from a single channel to the entire system behavior. Our model motor unit and simulation software may represent efficient tools not only for researchers studying the neural control of force production from a cellular perspective but also for instructors and students in motor physiology classroom settings. PMID:29695959

PyMUS: Python-Based Simulation Software for Virtual Experiments on Motor Unit System.

PubMed

Kim, Hojeong; Kim, Minjung

2018-01-01

We constructed a physiologically plausible computationally efficient model of a motor unit and developed simulation software that allows for integrative investigations of the input-output processing in the motor unit system. The model motor unit was first built by coupling the motoneuron model and muscle unit model to a simplified axon model. To build the motoneuron model, we used a recently reported two-compartment modeling approach that accurately captures the key cell-type-related electrical properties under both passive conditions (somatic input resistance, membrane time constant, and signal attenuation properties between the soma and the dendrites) and active conditions (rheobase current and afterhyperpolarization duration at the soma and plateau behavior at the dendrites). To construct the muscle unit, we used a recently developed muscle modeling approach that reflects the experimentally identified dependencies of muscle activation dynamics on isometric, isokinetic and dynamic variation in muscle length over a full range of stimulation frequencies. Then, we designed the simulation software based on the object-oriented programing paradigm and developed the software using open-source Python language to be fully operational using graphical user interfaces. Using the developed software, separate simulations could be performed for a single motoneuron, muscle unit and motor unit under a wide range of experimental input protocols, and a hierarchical analysis could be performed from a single channel to the entire system behavior. Our model motor unit and simulation software may represent efficient tools not only for researchers studying the neural control of force production from a cellular perspective but also for instructors and students in motor physiology classroom settings.

Model of environmental life cycle assessment for coal mining operations.

PubMed

Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

2016-08-15

This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. Copyright © 2016 Elsevier B.V. All rights reserved.

Substantiation of Structure of Adaptive Control Systems for Motor Units

NASA Astrophysics Data System (ADS)

Ovsyannikov, S. I.

2018-05-01

The article describes the development of new electronic control systems, in particular motor units, for small-sized agricultural equipment. Based on the analysis of traffic control systems, the main course of development of the conceptual designs of motor units has been defined. The systems aimed to control the course motion of the motor unit in automatic mode using the adaptive systems have been developed. The article presents structural models of the conceptual motor units based on electrically controlled systems by the operation of drive motors and adaptive systems that make the motor units completely automated.

Prediction of a Francis turbine prototype full load instability from investigations on the reduced scale model

NASA Astrophysics Data System (ADS)

Alligné, S.; Maruzewski, P.; Dinh, T.; Wang, B.; Fedorov, A.; Iosfin, J.; Avellan, F.

2010-08-01

The growing development of renewable energies combined with the process of privatization, lead to a change of economical energy market strategies. Instantaneous pricings of electricity as a function of demand or predictions, induces profitable peak productions which are mainly covered by hydroelectric power plants. Therefore, operators harness more hydroelectric facilities at full load operating conditions. However, the Francis Turbine features an axi-symmetric rope leaving the runner which may act under certain conditions as an internal energy source leading to instability. Undesired power and pressure fluctuations are induced which may limit the maximum available power output. BC Hydro experiences such constraints in a hydroelectric power plant consisting of four 435 MW Francis Turbine generating units, which is located in Canada's province of British Columbia. Under specific full load operating conditions, one unit experiences power and pressure fluctuations at 0.46 Hz. The aim of the paper is to present a methodology allowing prediction of this prototype's instability frequency from investigations on the reduced scale model. A new hydro acoustic vortex rope model has been developed in SIMSEN software, taking into account the energy dissipation due to the thermodynamic exchange between the gas and the surrounding liquid. A combination of measurements, CFD simulations and computation of eigenmodes of the reduced scale model installed on test rig, allows the accurate calibration of the vortex rope model parameters at the model scale. Then, transposition of parameters to the prototype according to similitude laws is applied and stability analysis of the power plant is performed. The eigenfrequency of 0.39 Hz related to the first eigenmode of the power plant is determined to be unstable. Predicted frequency of the full load power and pressure fluctuations at the unit unstable operating point is found to be in general agreement with the prototype measurements.

Upgrading the fuel-handling machine of the Novovoronezh nuclear power plant unit no. 5

NASA Astrophysics Data System (ADS)

Terekhov, D. V.; Dunaev, V. I.

2014-02-01

The calculation of safety parameters was carried out in the process of upgrading the fuel-handling machine (FHM) of the Novovoronezh nuclear power plant (NPP) unit no. 5 based on the results of quantitative safety analysis of nuclear fuel transfer operations using a dynamic logical-and-probabilistic model of the processing procedure. Specific engineering and design concepts that made it possible to reduce the probability of damaging the fuel assemblies (FAs) when performing various technological operations by an order of magnitude and introduce more flexible algorithms into the modernized FHM control system were developed. The results of pilot operation during two refueling campaigns prove that the total reactor shutdown time is lowered.

Economic Viability of Pumped-Storage Power Plants Equipped with Ternary Units and Considering Hydraulic Short-Circuit Operation

NASA Astrophysics Data System (ADS)

Chazarra, Manuel; Pérez-Díaz, Juan I.; García-González, Javier

2017-04-01

This paper analyses the economic viability of pumped-storage hydropower plants equipped with ternary units and considering hydraulic short-circuit operation. The analysed plant is assumed to participate in the day-ahead energy market and in the secondary regulation service of the Spanish power system. A deterministic day-ahead energy and reserve scheduling model is used to estimate the maximum theoretical income of the plant assuming perfect information of the next day prices and the residual demand curves of the secondary regulation reserve market. Results show that the pay-back periods with and without the hydraulic short-circuit operation are significantly lower than their expected lifetime and that the pay-back periods can be reduced with the inclusion of the hydraulic short-circuit operation.

Research on simulation of supercritical steam turbine system in large thermal power station

NASA Astrophysics Data System (ADS)

Zhou, Qiongyang

2018-04-01

In order to improve the stability and safety of supercritical steam turbine system operation in large thermal power station, the body of the steam turbine is modeled in this paper. And in accordance with the hierarchical modeling idea, the steam turbine body model, condensing system model, deaeration system model and regenerative system model are combined to build a simulation model of steam turbine system according to the connection relationship of each subsystem of steam turbine. Finally, the correctness of the model is verified by design and operation data of the 600MW supercritical unit. The results show that the maximum simulation error of the model is 2.15%, which meets the requirements of the engineering. This research provides a platform for the research on the variable operating conditions of the turbine system, and lays a foundation for the construction of the whole plant model of the thermal power plant.

Development of a Variable-Speed Residential Air-Source Integrated Heat Pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, C Keith; Shen, Bo; Munk, Jeffrey D

2014-01-01

A residential air-source integrated heat pump (AS-IHP) is under development in partnership with a U.S. manufacturer. A nominal 10.6 kW (3-ton) cooling capacity variable-speed unit, the system provides both space conditioning and water heating. This multi-functional unit can provide domestic water heating (DWH) in either full condensing (FC) (dedicated water heating or simultaneous space cooling and water heating) or desuperheating (DS) operation modes. Laboratory test data were used to calibrate a vapor-compression simulation model for each mode of operation. The model was used to optimize the internal control options for efficiency while maintaining acceptable comfort conditions and refrigerant-side pressures andmore » temperatures within allowable operating envelopes. Annual simulations were performed with the AS-IHP installed in a well-insulated house in five U.S. climate zones. The AS-IHP is predicted to use 45 to 60% less energy than a DOE minimum efficiency baseline system while meeting total annual space conditioning and water heating loads. Water heating energy use is lowered by 60 to 75% in cold to warmer climates, respectively. Plans are to field test the unit in Knoxville, TN.« less

Space-Shuttle Emulator Software

NASA Technical Reports Server (NTRS)

Arnold, Scott; Askew, Bill; Barry, Matthew R.; Leigh, Agnes; Mermelstein, Scott; Owens, James; Payne, Dan; Pemble, Jim; Sollinger, John; Thompson, Hiram;

Acoustic Characterization of Compact Jet Engine Simulator Units

NASA Technical Reports Server (NTRS)

Doty, Michael J.; Haskin, Henry H.

2013-01-01

Two dual-stream, heated jet, Compact Jet Engine Simulator (CJES) units are designed for wind tunnel acoustic experiments involving a Hybrid Wing Body (HWB) vehicle. The newly fabricated CJES units are characterized with a series of acoustic and flowfield investigations to ensure successful operation with minimal rig noise. To limit simulator size, consistent with a 5.8% HWB model, the CJES units adapt Ultra Compact Combustor (UCC) technology developed at the Air Force Research Laboratory. Stable and controllable operation of the combustor is demonstrated using passive swirl air injection and backpressuring of the combustion chamber. Combustion instability tones are eliminated using nonuniform flow conditioners in conjunction with upstream screens. Through proper flow conditioning, rig noise is reduced by more than 20 dB over a broad spectral range, but it is not completely eliminated at high frequencies. The low-noise chevron nozzle concept designed for the HWB test shows expected acoustic benefits when installed on the CJES unit, and consistency between CJES units is shown to be within 0.5 dB OASPL.

Capacity Adequacy and Revenue Sufficiency in Electricity Markets With Wind Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levin, Todd; Botterud, Audun

2015-05-01

We present a computationally efficient mixed-integer program (MIP) that determines optimal generator expansion decisions, as well as periodic unit commitment and dispatch. The model is applied to analyze the impact of increasing wind power capacity on the optimal generation mix and the profitability of thermal generators. In a case study, we find that increasing wind penetration reduces energy prices while the prices for operating reserves increase. Moreover, scarcity pricing for operating reserves through reserve shortfall penalties significantly impacts the prices and profitability of thermal generators. Without scarcity pricing, no thermal units are profitable, however scarcity pricing can ensure profitability formore » peaking units at high wind penetration levels. Capacity payments can also ensure profitability, but the payments required for baseload units to break even increase with the amount of wind power. The results indicate that baseload units are most likely to experience revenue sufficiency problems when wind penetration increases and new baseload units are only developed when natural gas prices are high and wind penetration is low.« less

A decision modeling for phasor measurement unit location selection in smart grid systems

NASA Astrophysics Data System (ADS)

Lee, Seung Yup

As a key technology for enhancing the smart grid system, Phasor Measurement Unit (PMU) provides synchronized phasor measurements of voltages and currents of wide-area electric power grid. With various benefits from its application, one of the critical issues in utilizing PMUs is the optimal site selection of units. The main aim of this research is to develop a decision support system, which can be used in resource allocation task for smart grid system analysis. As an effort to suggest a robust decision model and standardize the decision modeling process, a harmonized modeling framework, which considers operational circumstances of component, is proposed in connection with a deterministic approach utilizing integer programming. With the results obtained from the optimal PMU placement problem, the advantages and potential that the harmonized modeling process possesses are assessed and discussed.

Application of quality by design principles to the development and technology transfer of a major process improvement for the manufacture of a recombinant protein.

PubMed

Looby, Mairead; Ibarra, Neysi; Pierce, James J; Buckley, Kevin; O'Donovan, Eimear; Heenan, Mary; Moran, Enda; Farid, Suzanne S; Baganz, Frank

2011-01-01

This study describes the application of quality by design (QbD) principles to the development and implementation of a major manufacturing process improvement for a commercially distributed therapeutic protein produced in Chinese hamster ovary cell culture. The intent of this article is to focus on QbD concepts, and provide guidance and understanding on how the various components combine together to deliver a robust process in keeping with the principles of QbD. A fed-batch production culture and a virus inactivation step are described as representative examples of upstream and downstream unit operations that were characterized. A systematic approach incorporating QbD principles was applied to both unit operations, involving risk assessment of potential process failure points, small-scale model qualification, design and execution of experiments, definition of operating parameter ranges and process validation acceptance criteria followed by manufacturing-scale implementation and process validation. Statistical experimental designs were applied to the execution of process characterization studies evaluating the impact of operating parameters on product quality attributes and process performance parameters. Data from process characterization experiments were used to define the proven acceptable range and classification of operating parameters for each unit operation. Analysis of variance and Monte Carlo simulation methods were used to assess the appropriateness of process design spaces. Successful implementation and validation of the process in the manufacturing facility and the subsequent manufacture of hundreds of batches of this therapeutic protein verifies the approaches taken as a suitable model for the development, scale-up and operation of any biopharmaceutical manufacturing process. Copyright © 2011 American Institute of Chemical Engineers (AIChE).

Modeling the U.S. Border Patrol Tucson Sector for the Deployment and Operations of Border Security Forces

DTIC Science & Technology

2006-03-01

Crime_Trends_2005.pdf (accessed August 3, 2005). Consejo de Seguridad Publica , “Programa de Mediano Plazo 2004 - 2009: Seguridad Publica ,” http...international Southwest border. The issue of illegal human smuggling is not new to the United States- Mexico border or to law enforcement agencies...Operation Gatekeeper; Operation Hold the Line; Operation Stonegarden; Tucson Sector; US Border Patrol; US- Mexico border. 16. PRICE CODE 17. SECURITY

Rolling scheduling of electric power system with wind power based on improved NNIA algorithm

NASA Astrophysics Data System (ADS)

Xu, Q. S.; Luo, C. J.; Yang, D. J.; Fan, Y. H.; Sang, Z. X.; Lei, H.

2017-11-01

This paper puts forth a rolling modification strategy for day-ahead scheduling of electric power system with wind power, which takes the operation cost increment of unit and curtailed wind power of power grid as double modification functions. Additionally, an improved Nondominated Neighbor Immune Algorithm (NNIA) is proposed for solution. The proposed rolling scheduling model has further improved the operation cost of system in the intra-day generation process, enhanced the system’s accommodation capacity of wind power, and modified the key transmission section power flow in a rolling manner to satisfy the security constraint of power grid. The improved NNIA algorithm has defined an antibody preference relation model based on equal incremental rate, regulation deviation constraints and maximum & minimum technical outputs of units. The model can noticeably guide the direction of antibody evolution, and significantly speed up the process of algorithm convergence to final solution, and enhance the local search capability.

Scenarios for Low Carbon and Low Water Electric Power Plant Operations: Implications for Upstream Water Use.

PubMed

Dodder, Rebecca S; Barnwell, Jessica T; Yelverton, William H

2016-11-01

Electric sector water use, in particular for thermoelectric operations, is a critical component of the water-energy nexus. On a life cycle basis per unit of electricity generated, operational (e.g., cooling system) water use is substantially higher than water demands for the fuel cycle (e.g., natural gas and coal) and power plant manufacturing (e.g., equipment and construction). However, could shifting toward low carbon and low water electric power operations create trade-offs across the electricity life cycle? We compare business-as-usual with scenarios of carbon reductions and water constraints using the MARKet ALlocation (MARKAL) energy system model. Our scenarios show that, for water withdrawals, the trade-offs are minimal: operational water use accounts for over 95% of life cycle withdrawals. For water consumption, however, this analysis identifies potential trade-offs under some scenarios. Nationally, water use for the fuel cycle and power plant manufacturing can reach up to 26% of the total life cycle consumption. In the western United States, nonoperational consumption can even exceed operational demands. In particular, water use for biomass feedstock irrigation and manufacturing/construction of solar power facilities could increase with high deployment. As the United States moves toward lower carbon electric power operations, consideration of shifting water demands can help avoid unintended consequences.

An Analysis of Mathematical Models to Improve Counter-Drug Smuggling Operations

DTIC Science & Technology

2014-09-01

users. The target input file for the optimization algorithm has one segment of one target path on each row. Thus, if a target travels along a path...organization TOS time on station TSP Travelling Salesperson Problem USCG United States Coast Guard USN United States Navy UCONN University...of Connecticut UNCLOS United Nations Convention on Law of the Sea xv EXECUTIVE SUMMARY This research is motivated by the ongoing efforts of the

Development and testing of laser Doppler system components for wake vortex monitoring. Volume 1: Scanner development, laboratory and field testing and system modeling

NASA Technical Reports Server (NTRS)

Wilson, D. J.; Krause, M. C.; Coffey, E. W.; Huang, C. C.; Edwards, B. B.; Shrider, K. R.; Jetton, J. L.; Morrison, L. K.

1974-01-01

A servo-controlled range/elevation scanner for the laser Doppler velocimeter (LDV) was developed and tested in the field to assess its performance in detecting and monitoring aircraft trailing vortices in an airport environment. The elevation scanner provides a capability to manually point the LDV telescope at operator chosen angles from 3.2 deg. to 89.6 deg within 0.2 deg, or to automatically scan the units between operator chosen limits at operator chosen rates of 0.1 Hz to 0.5 Hz. The range scanner provides a capability to manually adjust the focal point of the system from a range of 32 meters to a range of 896 meters under operator control, or to scan between operator chosen limits and at rates from 0.1 Hz to 6.9 Hz. The scanner controls are designed to allow simulataneous range and elevation scanning so as to provide finger scan patterns, arc scan patterns, and vertical line scan patterns. The development and testing of the unit is discussed, along with a fluid dynamic model of the wake vortex developed in a laser Doppler vortex sensor simulation program.

A healthcare Lean Six Sigma System for postanesthesia care unit workflow improvement.

PubMed

Kuo, Alex Mu-Hsing; Borycki, Elizabeth; Kushniruk, Andre; Lee, Te-Shu

2011-01-01

The aim of this article is to propose a new model called Healthcare Lean Six Sigma System that integrates Lean and Six Sigma methodologies to improve workflow in a postanesthesia care unit. The methodology of the proposed model is fully described. A postanesthesia care unit case study is also used to demonstrate the benefits of using the Healthcare Lean Six Sigma System model by combining Lean and Six Sigma methodologies together. The new model bridges the service gaps between health care providers and patients, balances the requirements of health care managers, and delivers health care services to patients by taking the benefits of the Lean speed and Six Sigma high-quality principles. The full benefits of the new model will be realized when applied at both strategic and operational levels. For further research, we will examine how the proposed model is used in different real-world case studies.

77 FR 24950 - Midwest Independent Transmission, System Operator, Inc.; Supplemental Notice of Technical Conference

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

... Conference. The Midwest Independent Transmission System Operator, Inc. (MISO) and/or Potomac Economics, Inc... MWs? 4. MISO states that ``[i]n principle, voltage issues would be modeled using thermal constraints... committed? Please explain. b. Can units committed based on economics in the SCUC and SCED processes be...

75 FR 29571 - Notice of Proposed Information Collection for Public Comment; Training Evaluation Form

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-26

... public housing agencies (PHAs) and establishes requirements for PHAs to convert to asset management... regarding asset management. Under Sec. 990.260(a), PHAs that own and operate 250 or more dwelling rental units must operate using an asset management model consistent with the subpart H regulations. However...

Design and optimisation of novel configurations of stormwater constructed wetlands

NASA Astrophysics Data System (ADS)

Kiiza, Christopher

2017-04-01

Constructed wetlands (CWs) are recognised as a cost-effective technology for wastewater treatment. CWs have been deployed and could be retrofitted into existing urban drainage systems to prevent surface water pollution, attenuate floods and act as sources for reusable water. However, there exist numerous criteria for design configuration and operation of CWs. The aim of the study was to examine effects of design and operational variables on performance of CWs. To achieve this, 8 novel designs of vertical flow CWs were continuously operated and monitored (weekly) for 2years. Pollutant removal efficiency in each CW unit was evaluated from physico-chemical analyses of influent and effluent water samples. Hybrid optimised multi-layer perceptron artificial neural networks (MLP ANNs) were applied to simulate treatment efficiency in the CWs. Subsequently, predictive and analytical models were developed for each design unit. Results show models have sound generalisation abilities; with various design configurations and operational variables influencing performance of CWs. Although some design configurations attained faster and higher removal efficiencies than others; all 8 CW designs produced effluents permissible for discharge into watercourses with strict regulatory standards.

Solar thermochemical processing system and method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wegeng, Robert S.; Humble, Paul H.; Krishnan, Shankar

A solar thermochemical processing system is disclosed. The system includes a first unit operation for receiving concentrated solar energy. Heat from the solar energy is used to drive the first unit operation. The first unit operation also receives a first set of reactants and produces a first set of products. A second unit operation receives the first set of products from the first unit operation and produces a second set of products. A third unit operation receives heat from the second unit operation to produce a portion of the first set of reactants.

MO200: a model for evaluation safeguards through material accountability for a 200 tonne per year mixed-oxide fuel-rod fabrication plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandborn, R.H.

1976-01-01

M0200, a computer simulation model, was used to investigate the safeguarding of plutonium dioxide. The computer program operating the model was constructed so that replicate runs could provide data for statistical analysis of the distributions of the randomized variables. The plant model was divided into material balance areas associated with definable unit processes. Indicators of plant operations studied were modified end-of-shift material balances, end-of-blend errors formed by closing material balances between blends, and cumulative sums of the differences between actual and expected performances. (auth)

Contact drying: a review of experimental and mechanistic modeling approaches.

PubMed

Sahni, Ekneet Kaur; Chaudhuri, Bodhisattwa

2012-09-15

Drying is one of the most complex unit operations with simultaneous heat and mass transfer. The contact drying process is also not well understood as several physical phenomena occur concurrently. This paper reviews current experimental and modeling approaches employed towards a better understanding of the contact drying operation. Additionally, an overview of some fundamental aspects relating to contact drying is provided. A brief discussion of some model extensions such as incorporation of noncontact forces, interstitial fluids and attrition rate is also presented. Copyright © 2012 Elsevier B.V. All rights reserved.

Data-driven modeling and predictive control for boiler-turbine unit using fuzzy clustering and subspace methods.

PubMed

Wu, Xiao; Shen, Jiong; Li, Yiguo; Lee, Kwang Y

2014-05-01

This paper develops a novel data-driven fuzzy modeling strategy and predictive controller for boiler-turbine unit using fuzzy clustering and subspace identification (SID) methods. To deal with the nonlinear behavior of boiler-turbine unit, fuzzy clustering is used to provide an appropriate division of the operation region and develop the structure of the fuzzy model. Then by combining the input data with the corresponding fuzzy membership functions, the SID method is extended to extract the local state-space model parameters. Owing to the advantages of the both methods, the resulting fuzzy model can represent the boiler-turbine unit very closely, and a fuzzy model predictive controller is designed based on this model. As an alternative approach, a direct data-driven fuzzy predictive control is also developed following the same clustering and subspace methods, where intermediate subspace matrices developed during the identification procedure are utilized directly as the predictor. Simulation results show the advantages and effectiveness of the proposed approach. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Integrating Solar PV in Utility System Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mills, A.; Botterud, A.; Wu, J.

2013-10-31

This study develops a systematic framework for estimating the increase in operating costs due to uncertainty and variability in renewable resources, uses the framework to quantify the integration costs associated with sub-hourly solar power variability and uncertainty, and shows how changes in system operations may affect these costs. Toward this end, we present a statistical method for estimating the required balancing reserves to maintain system reliability along with a model for commitment and dispatch of the portfolio of thermal and renewable resources at different stages of system operations. We estimate the costs of sub-hourly solar variability, short-term forecast errors, andmore » day-ahead (DA) forecast errors as the difference in production costs between a case with “realistic” PV (i.e., subhourly solar variability and uncertainty are fully included in the modeling) and a case with “well behaved” PV (i.e., PV is assumed to have no sub-hourly variability and can be perfectly forecasted). In addition, we highlight current practices that allow utilities to compensate for the issues encountered at the sub-hourly time frame with increased levels of PV penetration. In this analysis we use the analytical framework to simulate utility operations with increasing deployment of PV in a case study of Arizona Public Service Company (APS), a utility in the southwestern United States. In our analysis, we focus on three processes that are important in understanding the management of PV variability and uncertainty in power system operations. First, we represent the decisions made the day before the operating day through a DA commitment model that relies on imperfect DA forecasts of load and wind as well as PV generation. Second, we represent the decisions made by schedulers in the operating day through hour-ahead (HA) scheduling. Peaking units can be committed or decommitted in the HA schedules and online units can be redispatched using forecasts that are improved relative to DA forecasts, but still imperfect. Finally, we represent decisions within the operating hour by schedulers and transmission system operators as real-time (RT) balancing. We simulate the DA and HA scheduling processes with a detailed unit-commitment (UC) and economic dispatch (ED) optimization model. This model creates a least-cost dispatch and commitment plan for the conventional generating units using forecasts and reserve requirements as inputs. We consider only the generation units and load of the utility in this analysis; we do not consider opportunities to trade power with neighboring utilities. We also do not consider provision of reserves from renewables or from demand-side options. We estimate dynamic reserve requirements in order to meet reliability requirements in the RT operations, considering the uncertainty and variability in load, solar PV, and wind resources. Balancing reserve requirements are based on the 2.5th and 97.5th percentile of 1-min deviations from the HA schedule in a previous year. We then simulate RT deployment of balancing reserves using a separate minute-by-minute simulation of deviations from the HA schedules in the operating year. In the simulations we assume that balancing reserves can be fully deployed in 10 min. The minute-by-minute deviations account for HA forecasting errors and the actual variability of the load, wind, and solar generation. Using these minute-by-minute deviations and deployment of balancing reserves, we evaluate the impact of PV on system reliability through the calculation of the standard reliability metric called Control Performance Standard 2 (CPS2). Broadly speaking, the CPS2 score measures the percentage of 10-min periods in which a balancing area is able to balance supply and demand within a specific threshold. Compliance with the North American Electric Reliability Corporation (NERC) reliability standards requires that the CPS2 score must exceed 90% (i.e., the balancing area must maintain adequate balance for 90% of the 10-min periods). The combination of representing DA forecast errors in the DA commitments, using 1-min PV data to simulate RT balancing, and estimates of reliability performance through the CPS2 metric, all factors that are important to operating systems with increasing amounts of PV, makes this study unique in its scope.« less

Fuel consumption models for pine flatwoods fuel types in the southeastern United States

Treesearch

Clinton S. Wright

2013-01-01

Modeling fire effects, including terrestrial and atmospheric carbon fluxes and pollutant emissions during wildland fires, requires accurate predictions of fuel consumption. Empirical models were developed for predicting fuel consumption from fuel and environmental measurements on a series of operational prescribed fires in pine flatwoods ecosystems in the southeastern...

Total Force Fitness in units part 1: military demand-resource model.

PubMed

Bates, Mark J; Fallesen, Jon J; Huey, Wesley S; Packard, Gary A; Ryan, Diane M; Burke, C Shawn; Smith, David G; Watola, Daniel J; Pinder, Evette D; Yosick, Todd M; Estrada, Armando X; Crepeau, Loring; Bowles, Stephen V

2013-11-01

The military unit is a critical center of gravity in the military's efforts to enhance resilience and the health of the force. The purpose of this article is to augment the military's Total Force Fitness (TFF) guidance with a framework of TFF in units. The framework is based on a Military Demand-Resource model that highlights the dynamic interactions across demands, resources, and outcomes. A joint team of subject-matter experts identified key variables representing unit fitness demands, resources, and outcomes. The resulting framework informs and supports leaders, support agencies, and enterprise efforts to strengthen TFF in units by (1) identifying TFF unit variables aligned with current evidence and operational practices, (2) standardizing communication about TFF in units across the Department of Defense enterprise in a variety of military organizational contexts, (3) improving current resources including evidence-based actions for leaders, (4) identifying and addressing of gaps, and (5) directing future research for enhancing TFF in units. These goals are intended to inform and enhance Service efforts to develop Service-specific TFF models, as well as provide the conceptual foundation for a follow-on article about TFF metrics for units. Reprint & Copyright © 2013 Association of Military Surgeons of the U.S.

PREMChlor: Probabilistic Remediation Evaluation Model for Chlorinated Solvents

DTIC Science & Technology

2010-03-01

Council O&M Operation & Management PAT pump-and-treat PCE tetrachloroethylene PDFs Probability density functions PRBs Permeable reactive barriers...includes a one-time capital cost and a total operation & management (O&M) cost in present net value (NPV) for a certain remediation period. The...Generally, the costs of plume treatment include the capital cost (treatment volume multiply by the unit cost) and the annual operation & Management (O&M

Prevalence of Posttraumatic Stress Disorder in Remotely Piloted Aircraft Operators in the United States Air Force

DTIC Science & Technology

2016-05-24

common feature of the depressive and anxiety disorders: a test of the revised integrative hierarchical model in a national sample. J Abnorm Psychol...proliferation of this unique form of warfare, concerns have been raised regarding the psychological impact such operations have on RPA operators directly...and clinical interviews utilizing the Clinician Administered Psychological Survey to determine the nature of the respondents’ stressful military

Basic Techniques in Environmental Simulation.

DTIC Science & Technology

1982-07-01

the devel- ’I or oper is liable for all necessary changes in the model or its supporting computer software . After the 90-day warranty expires, the user...processing unit, that part of a computer which accom- plishes arithmetic and logical operations DCFLOS Dynamic cloud -free line-of-sight, a simulation... Software Development ......... 12 1.7.7 Operational Environment, Interfaces, and Constraints. . 12 1.7.8 Effectiveness Evaluation, Value Analysis, and

RTD-based Material Tracking in a Fully-Continuous Dry Granulation Tableting Line.

PubMed

Martinetz, M C; Karttunen, A-P; Sacher, S; Wahl, P; Ketolainen, J; Khinast, J G; Korhonen, O

2018-06-06

Continuous manufacturing (CM) offers quality and cost-effectiveness benefits over currently dominating batch processing. One challenge that needs to be addressed when implementing CM is traceability of materials through the process, which is needed for the batch/lot definition and control strategy. In this work the residence time distributions (RTD) of single unit operations (blender, roller compactor and tablet press) of a continuous dry granulation tableting line were captured with NIR based methods at selected mass flow rates to create training data. RTD models for continuous operated unit operations and the entire line were developed based on transfer functions. For semi-continuously operated bucket conveyor and pneumatic transport an assumption based the operation frequency was used. For validation of the parametrized process model, a pre-defined API step change and its propagation through the manufacturing line was computed and compared to multi-scale experimental runs conducted with the fully assembled continuous operated manufacturing line. This novel approach showed a very good prediction power at the selected mass flow rates for a complete continuous dry granulation line. Furthermore, it shows and proves the capabilities of process simulation as a tool to support development and control of pharmaceutical manufacturing processes. Copyright © 2018. Published by Elsevier B.V.

IEA Wind Task 26. Wind Technology, Cost and Performance Trends in Denmark, Germany, Ireland, Norway, the European Union, and the United States. 2007 - 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vitina, Aisma; Luers, Silke; Wallasch, Anna-Kathrin

This report builds from a similar previous analysis (Schwabe et al., 2011) exploring the differences in cost of wind energy in 2008 among countries participating in IEA Wind Task 26 at that time. The levelized cost of energy (LCOE) is a widely recognized metric for understanding how technology, capital investment, operations, and financing impact the life-cycle cost of building and operating a wind plant. Schwabe et al. (2011) apply a spreadsheet-based cash flow model developed by the Energy Research Centre of the Netherlands (ECN) to estimate LCOE. This model is a detailed, discounted cash flow model used to represent themore » various cost structures in each of the participating countries from the perspective of a financial investor in a domestic wind energy project. This model is used for the present analysis as well, and comparisons are made for those countries who contributed to both reports, Denmark, Germany, and the United States.« less

A comparison of GLAS SAT and NMC high resolution NOSAT forecasts from 19 and 11 February 1976

NASA Technical Reports Server (NTRS)

Atlas, R.

1979-01-01

A subjective comparison of the Goddard Laboratory for Atmospheric Sciences (GLAS) and the National Meteorological Center (NMC) high resolution model forecasts is presented. Two cases where NMC's operational model in 1976 had serious difficulties in forecasting for the United States were examined. For each of the cases, the GLAS model forecasts from initial conditions which included satellite sounding data were compared directly to the NMC higher resolution model forecasts, from initial conditions which excluded the satellite data. The comparison showed that the GLAS satellite forecasts significantly improved upon the current NMC operational model's predictions in both cases.

Unit conversion as a source of misclassification in US birthweight data.

PubMed

Umbach, D M

2000-01-01

This study explains why frequency polygons for US birthweights in 100-g weight classes appear spiky compared with their European counterparts. A probability model is used to describe how unit conversion can induce misclassification. Birthweights from the United States and Norway are used to illustrate that misclassification operates in grouped US data. Spikiness represents misclassification that arises when measured birthweights are rounded to the nearer ounce, converted to grams, and then grouped into weight classes. Misclassification is ameliorated, not eliminated, with 200-g weight classes. Possible biases from misclassification should be carefully evaluated when fitting statistical models to grouped US birthweights.

Δ L =3 processes: Proton decay and the LHC

NASA Astrophysics Data System (ADS)

Fonseca, Renato M.; Hirsch, Martin; Srivastava, Rahul

2018-04-01

We discuss lepton number violation in three units. From an effective field theory point of view, Δ L =3 processes can only arise from dimension 9 or higher operators. These operators also violate baryon number, hence many of them will induce proton decay. Given the high dimensionality of these operators, in order to have a proton half-life in the observable range, the new physics associated to Δ L =3 processes should be at a scale as low as 1 TeV. This opens up the possibility of searching for such processes not only in proton decay experiments but also at the LHC. In this work we analyze the relevant d =9 , 11, 13 operators which violate lepton number in three units. We then construct one simple concrete model with interesting low- and high-energy phenomenology.

The high speed interconnect system architecture and operation

NASA Astrophysics Data System (ADS)

Anderson, Steven C.

The design and operation of a fiber-optic high-speed interconnect system (HSIS) being developed to meet the requirements of future avionics and flight-control hardware with distributed-system architectures are discussed. The HSIS is intended for 100-Mb/s operation of a local-area network with up to 256 stations. It comprises a bus transmission system (passive star couplers and linear media linked by active elements) and network interface units (NIUs). Each NIU is designed to perform the physical, data link, network, and transport functions defined by the ISO OSI Basic Reference Model (1982 and 1983) and incorporates a fiber-optic transceiver, a high-speed protocol based on the SAE AE-9B linear token-passing data bus (1986), and a specialized application interface unit. The operating modes and capabilities of HSIS are described in detail and illustrated with diagrams.

Sensitivity of the Community Multiscale Air Quality (CMAQ) Model v4.7 Results for the Eastern United States to MM5 and WRF Meteorological Drivers

EPA Science Inventory

This paper presents a comparison of the operational performance of two Community Multiscale Air Quality (CMAQ) model v4.7 simulations that utilize input data from the 5th generation Mesoscale Model MM5 and the Weather Research and Forecasting (WRF) meteorological models.

HOTS: A Hierarchy of Event-Based Time-Surfaces for Pattern Recognition.

PubMed

Lagorce, Xavier; Orchard, Garrick; Galluppi, Francesco; Shi, Bertram E; Benosman, Ryad B

2017-07-01

This paper describes novel event-based spatio-temporal features called time-surfaces and how they can be used to create a hierarchical event-based pattern recognition architecture. Unlike existing hierarchical architectures for pattern recognition, the presented model relies on a time oriented approach to extract spatio-temporal features from the asynchronously acquired dynamics of a visual scene. These dynamics are acquired using biologically inspired frameless asynchronous event-driven vision sensors. Similarly to cortical structures, subsequent layers in our hierarchy extract increasingly abstract features using increasingly large spatio-temporal windows. The central concept is to use the rich temporal information provided by events to create contexts in the form of time-surfaces which represent the recent temporal activity within a local spatial neighborhood. We demonstrate that this concept can robustly be used at all stages of an event-based hierarchical model. First layer feature units operate on groups of pixels, while subsequent layer feature units operate on the output of lower level feature units. We report results on a previously published 36 class character recognition task and a four class canonical dynamic card pip task, achieving near 100 percent accuracy on each. We introduce a new seven class moving face recognition task, achieving 79 percent accuracy.This paper describes novel event-based spatio-temporal features called time-surfaces and how they can be used to create a hierarchical event-based pattern recognition architecture. Unlike existing hierarchical architectures for pattern recognition, the presented model relies on a time oriented approach to extract spatio-temporal features from the asynchronously acquired dynamics of a visual scene. These dynamics are acquired using biologically inspired frameless asynchronous event-driven vision sensors. Similarly to cortical structures, subsequent layers in our hierarchy extract increasingly abstract features using increasingly large spatio-temporal windows. The central concept is to use the rich temporal information provided by events to create contexts in the form of time-surfaces which represent the recent temporal activity within a local spatial neighborhood. We demonstrate that this concept can robustly be used at all stages of an event-based hierarchical model. First layer feature units operate on groups of pixels, while subsequent layer feature units operate on the output of lower level feature units. We report results on a previously published 36 class character recognition task and a four class canonical dynamic card pip task, achieving near 100 percent accuracy on each. We introduce a new seven class moving face recognition task, achieving 79 percent accuracy.

40 CFR 60.2725 - May I conduct a repeat performance test to establish new operating limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model... during any performance test used to demonstrate compliance. Model Rule—Monitoring ...

40 CFR 60.2725 - May I conduct a repeat performance test to establish new operating limits?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model... during any performance test used to demonstrate compliance. Model Rule—Monitoring ...

AN OVERVIEW OF THE INTEROPERABILITY ROADMAP FOR COM/.NET-BASED CAPE-OPEN

EPA Science Inventory

The CAPE-OPEN standard interfaces have been designed to permit flexibility and modularization of process simulation environments (PMEs) in order to use process modeling components such as unit operation or thermodynamic property models across a range of tolls employed in the life...

EnergySolution's Clive Disposal Facility Operational Research Model - 13475

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nissley, Paul; Berry, Joanne

2013-07-01

EnergySolutions owns and operates a licensed, commercial low-level radioactive waste disposal facility located in Clive, Utah. The Clive site receives low-level radioactive waste from various locations within the United States via bulk truck, containerised truck, enclosed truck, bulk rail-cars, rail boxcars, and rail inter-modals. Waste packages are unloaded, characterized, processed, and disposed of at the Clive site. Examples of low-level radioactive waste arriving at Clive include, but are not limited to, contaminated soil/debris, spent nuclear power plant components, and medical waste. Generators of low-level radioactive waste typically include nuclear power plants, hospitals, national laboratories, and various United States government operatedmore » waste sites. Over the past few years, poor economic conditions have significantly reduced the number of shipments to Clive. With less revenue coming in from processing shipments, Clive needed to keep its expenses down if it was going to maintain past levels of profitability. The Operational Research group of EnergySolutions were asked to develop a simulation model to help identify any improvement opportunities that would increase overall operating efficiency and reduce costs at the Clive Facility. The Clive operations research model simulates the receipt, movement, and processing requirements of shipments arriving at the facility. The model includes shipment schedules, processing times of various waste types, labor requirements, shift schedules, and site equipment availability. The Clive operations research model has been developed using the WITNESS{sup TM} process simulation software, which is developed by the Lanner Group. The major goals of this project were to: - identify processing bottlenecks that could reduce the turnaround time from shipment arrival to disposal; - evaluate the use (or idle time) of labor and equipment; - project future operational requirements under different forecasted scenarios. By identifying processing bottlenecks and unused equipment and/or labor, improvements to operating efficiency could be determined and appropriate cost saving measures implemented. Model runs forecasting various scenarios helped illustrate potential impacts of certain conditions (e.g. 20% decrease in shipments arrived), variables (e.g. 20% decrease in labor), or other possible situations. (authors)« less

Project Profile: Hydrogen Fuel Cell Mobile Lighting Tower (HFCML)

NASA Technical Reports Server (NTRS)

McLaughlin, Russell

2013-01-01

NASA is committed to finding innovative solutions that improve the operational performance of ground support equipment while providing environment and cost benefits, as well. Through the Hydrogen Fuel Cell Mobile Lighting Tower (HFCML) project, NASA gained operational exposure to a novel application of high efficiency technologies. Traditionally, outdoor lighting and auxiliary power at security gates, launch viewing sites, fallback areas, outage support, and special events is provided by diesel generators with metal halide lights. Diesel generators inherently contribute to C02, NOx, particulate emissions, and are very noisy. In 2010, engineers from NASA's Technology Evaluation for Environmental Risk Mitigation Principal Center (TEERM) introduced KSC operations to a novel technology for outdoor lighting needs. Developed by a team led by Sandia National Laboratory (SNL), the technology pairs a 5kW hydrogen fuel cell with robust high efficiency plasma lights in a towable trailer. Increased efficiency, in both the fuel cell power source and lighting load, yields longer run times between fueling operations while providing greater auxiliary power. Because of the unit's quiet operation and no exhaust fumes, it is capable of being used indoors and in emergency situations, and meets the needs of all other operational roles for metal halide/diesel generators. The only discharge is some water and warm air. Environmental benefits include elimination of diesel particulate emissions and estimated 73% greenhouse gas emissions savings when the hydrogen source is natural gas (per GREET model). As the technology matures the costs could become competitive for the fuel cell units which are approximately 5 times diesel units. Initial operational . concerns included the hydrogen storage tanks and valves, lightning safety/grounding, and required operating and refueling procedures. TEERM facilitated technical information exchange (design drawings, technical standards, and operations manuals) necessary for KSC hydrogen system experts to approve use of the HFCML unit, including initiating the environmental checklist (i.e. exterior lighting waiver due to sea turtles), and development of operations and maintenance instructions. TEERM worked with SNL to establish a bailment agreement for KSC to utilize a Beta unit as part of normal Center Operations for a period of twelve months.

77 FR 29701 - Impact of Construction (Under a Combined License) of New Nuclear Power Plant Units on Operating...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-18

... New Nuclear Power Plant Units on Operating Units at Multi-Unit Sites AGENCY: Nuclear Regulatory... construct and operate new nuclear power plants (NPPs) on multi-unit sites to provide an evaluation of the... License) of New Nuclear Power Plants on Operating Units at Multi-Unit Sites (Package). ML112630039 Federal...

Modelisation de l'historique d'operation de groupes turbine-alternateur

NASA Astrophysics Data System (ADS)

Szczota, Mickael

Because of their ageing fleet, the utility managers are increasingly in needs of tools that can help them to plan efficiently maintenance operations. Hydro-Quebec started a project that aim to foresee the degradation of their hydroelectric runner, and use that information to classify the generating unit. That classification will help to know which generating unit is more at risk to undergo a major failure. Cracks linked to the fatigue phenomenon are a predominant degradation mode and the loading sequences applied to the runner is a parameter impacting the crack growth. So, the aim of this memoir is to create a generator able to generate synthetic loading sequences that are statistically equivalent to the observed history. Those simulated sequences will be used as input in a life assessment model. At first, we describe how the generating units are operated by Hydro-Quebec and analyse the available data, the analysis shows that the data are non-stationnary. Then, we review modelisation and validation methods. In the following chapter a particular attention is given to a precise description of the validation and comparison procedure. Then, we present the comparison of three kind of model : Discrete Time Markov Chains, Discrete Time Semi-Markov Chains and the Moving Block Bootstrap. For the first two models, we describe how to take account for the non-stationnarity. Finally, we show that the Markov Chain is not adapted for our case, and that the Semi-Markov chains are better when they include the non-stationnarity. The final choice between Semi-Markov Chains and the Moving Block Bootstrap depends of the user. But, with a long term vision we recommend the use of Semi-Markov chains for their flexibility. Keywords: Stochastic models, Models validation, Reliability, Semi-Markov Chains, Markov Chains, Bootstrap

Longitudinal comparative evaluation of the equivalence of an integrated peer-support and clinical staffing model for residential mental health rehabilitation: a mixed methods protocol incorporating multiple stakeholder perspectives.

PubMed

Parker, Stephen; Dark, Frances; Newman, Ellie; Korman, Nicole; Meurk, Carla; Siskind, Dan; Harris, Meredith

2016-06-02

A novel staffing model integrating peer support workers and clinical staff within a unified team is being trialled at community based residential rehabilitation units in Australia. A mixed-methods protocol for the longitudinal evaluation of the outcomes, expectations and experiences of care by consumers and staff under this staffing model in two units will be compared to one unit operating a traditional clinical staffing. The study is unique with regards to the context, the longitudinal approach and consideration of multiple stakeholder perspectives. The longitudinal mixed methods design integrates a quantitative evaluation of the outcomes of care for consumers at three residential rehabilitation units with an applied qualitative research methodology. The quantitative component utilizes a prospective cohort design to explore whether equivalent outcomes are achieved through engagement at residential rehabilitation units operating integrated and clinical staffing models. Comparative data will be available from the time of admission, discharge and 12-month period post-discharge from the units. Additionally, retrospective data for the 12-month period prior to admission will be utilized to consider changes in functioning pre and post engagement with residential rehabilitation care. The primary outcome will be change in psychosocial functioning, assessed using the total score on the Health of the Nation Outcome Scales (HoNOS). Planned secondary outcomes will include changes in symptomatology, disability, recovery orientation, carer quality of life, emergency department presentations, psychiatric inpatient bed days, and psychological distress and wellbeing. Planned analyses will include: cohort description; hierarchical linear regression modelling of the predictors of change in HoNOS following CCU care; and descriptive comparisons of the costs associated with the two staffing models. The qualitative component utilizes a pragmatic approach to grounded theory, with collection of data from consumers and staff at multiple time points exploring their expectations, experiences and reflections on the care provided by these services. It is expected that the new knowledge gained through this study will guide the adaptation of these and similar services. For example, if differential outcomes are achieved for consumers under the integrated and clinical staffing models this may inform staffing guidelines.

OSPREY Model Development Status Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veronica J Rutledge

2014-04-01

During the processing of used nuclear fuel, volatile radionuclides will be discharged to the atmosphere if no recovery processes are in place to limit their release. The volatile radionuclides of concern are 3H, 14C, 85Kr, and 129I. Methods are being developed, via adsorption and absorption unit operations, to capture these radionuclides. It is necessary to model these unit operations to aid in the evaluation of technologies and in the future development of an advanced used nuclear fuel processing plant. A collaboration between Fuel Cycle Research and Development Offgas Sigma Team member INL and a NEUP grant including ORNL, Syracuse University,more » and Georgia Institute of Technology has been formed to develop off gas models and support off gas research. Georgia Institute of Technology is developing fundamental level model to describe the equilibrium and kinetics of the adsorption process, which are to be integrated with OSPREY. This report discusses the progress made on expanding OSPREY to be multiple component and the integration of macroscale and microscale level models. Also included in this report is a brief OSPREY user guide.« less

Visualization of the Eastern Renewable Generation Integration Study: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gruchalla, Kenny; Novacheck, Joshua; Bloom, Aaron

The Eastern Renewable Generation Integration Study (ERGIS), explores the operational impacts of the wide spread adoption of wind and solar photovoltaics (PV) resources in the U.S. Eastern Interconnection and Quebec Interconnection (collectively, EI). In order to understand some of the economic and reliability challenges of managing hundreds of gigawatts of wind and PV generation, we developed state of the art tools, data, and models for simulating power system operations using hourly unit commitment and 5-minute economic dispatch over an entire year. Using NREL's high-performance computing capabilities and new methodologies to model operations, we found that the EI, as simulated withmore » evolutionary change in 2026, could balance the variability and uncertainty of wind and PV at a 5-minute level under a variety of conditions. A large-scale display and a combination of multiple coordinated views and small multiples were used to visually analyze the four large highly multivariate scenarios with high spatial and temporal resolutions. state of the art tools, data, and models for simulating power system operations using hourly unit commitment and 5-minute economic dispatch over an entire year. Using NRELs high-performance computing capabilities and new methodologies to model operations, we found that the EI, as simulated with evolutionary change in 2026, could balance the variability and uncertainty of wind and PV at a 5-minute level under a variety of conditions. A large-scale display and a combination of multiple coordinated views and small multiples were used to visually analyze the four large highly multivariate scenarios with high spatial and temporal resolutions.« less

Bonneville Powerhouse 2 Fish Guidance Efficiency Studies: CFD Model of the Forebay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rakowski, Cynthia L.; Serkowski, John A.; Richmond, Marshall C.

2012-07-01

In ongoing work, U.S. Army Corps of Engineers, Portland District (CENWP) is seeking to better understand and improve the conditions within the Bonneville Powerhouse 2 (B2) turbine intakes to improve survival of downstream migrant salmonid smolt. In this study, the existing B2 forebay computational fluid dynamics (CFD) model was modified to include a more detailed representation of all B2 turbine intakes. The modified model was validated to existing field-measured forebay ADCP velocities. The initial CFD model scenarios tested a single project operation and the impact of adding the Behavior Guidance System (BGS) or Corner Collector. These structures had impacts onmore » forebay flows. Most notable was that the addition of the BGS and Corner Collector reduced the lateral extent of the recirculation areas on the Washington shore and Cascade Island and reduced the flow velocity parallel to the powerhouse in front of Units 11 and 12. For these same cases, at the turbine intakes across the powerhouse, there was very little difference in the flow volume into the gatewell for the clean forebay, and the forebay with the BGS in place and/or the Corner Collector operating. The largest differences were at Units 11 to 13. The CFD model cases testing the impact of the gatewell slot fillers showed no impact to the forebay flows, but large differences within the gatewells. With the slot fillers, the flow above the standard traveling screen and into the gatewell increased (about 100 cfs at each turbine intake) and the gap flow decreased across the powerhouse for all cases. The increased flow up the gatewell was further enhanced with only half the units operating. The flow into the gatewell slot was increased about 35 cfs for each bay of each intake across the powerhouse; this change was uniform across the powerhouse. The flows in the gatewell of Unit 12, the most impacted unit for the scenarios, was evaluated. In front of the vertical barrier screen, the CFD model with slot fillers showed reduced the maximum velocities (in spite of the increased the flow into the gatewell), and decreased the area of recirculation. The area near the VBS exceeding the normal velocity criteria of 1 ft/s was reduced and the flows were more balanced.« less

Goal-directed control with cortical units that are gated by both top-down feedback and oscillatory coherence.

PubMed

Kerr, Robert R; Grayden, David B; Thomas, Doreen A; Gilson, Matthieu; Burkitt, Anthony N

2014-01-01

The brain is able to flexibly select behaviors that adapt to both its environment and its present goals. This cognitive control is understood to occur within the hierarchy of the cortex and relies strongly on the prefrontal and premotor cortices, which sit at the top of this hierarchy. Pyramidal neurons, the principal neurons in the cortex, have been observed to exhibit much stronger responses when they receive inputs at their soma/basal dendrites that are coincident with inputs at their apical dendrites. This corresponds to inputs from both lower-order regions (feedforward) and higher-order regions (feedback), respectively. In addition to this, coherence between oscillations, such as gamma oscillations, in different neuronal groups has been proposed to modulate and route communication in the brain. In this paper, we develop a simple, but novel, neural mass model in which cortical units (or ensembles) exhibit gamma oscillations when they receive coherent oscillatory inputs from both feedforward and feedback connections. By forming these units into circuits that can perform logic operations, we identify the different ways in which operations can be initiated and manipulated by top-down feedback. We demonstrate that more sophisticated and flexible top-down control is possible when the gain of units is modulated by not only top-down feedback but by coherence between the activities of the oscillating units. With these types of units, it is possible to not only add units to, or remove units from, a higher-level unit's logic operation using top-down feedback, but also to modify the type of role that a unit plays in the operation. Finally, we explore how different network properties affect top-down control and processing in large networks. Based on this, we make predictions about the likely connectivities between certain brain regions that have been experimentally observed to be involved in goal-directed behavior and top-down attention.

Goal-directed control with cortical units that are gated by both top-down feedback and oscillatory coherence

PubMed Central

Kerr, Robert R.; Grayden, David B.; Thomas, Doreen A.; Gilson, Matthieu; Burkitt, Anthony N.

2014-01-01

The brain is able to flexibly select behaviors that adapt to both its environment and its present goals. This cognitive control is understood to occur within the hierarchy of the cortex and relies strongly on the prefrontal and premotor cortices, which sit at the top of this hierarchy. Pyramidal neurons, the principal neurons in the cortex, have been observed to exhibit much stronger responses when they receive inputs at their soma/basal dendrites that are coincident with inputs at their apical dendrites. This corresponds to inputs from both lower-order regions (feedforward) and higher-order regions (feedback), respectively. In addition to this, coherence between oscillations, such as gamma oscillations, in different neuronal groups has been proposed to modulate and route communication in the brain. In this paper, we develop a simple, but novel, neural mass model in which cortical units (or ensembles) exhibit gamma oscillations when they receive coherent oscillatory inputs from both feedforward and feedback connections. By forming these units into circuits that can perform logic operations, we identify the different ways in which operations can be initiated and manipulated by top-down feedback. We demonstrate that more sophisticated and flexible top-down control is possible when the gain of units is modulated by not only top-down feedback but by coherence between the activities of the oscillating units. With these types of units, it is possible to not only add units to, or remove units from, a higher-level unit's logic operation using top-down feedback, but also to modify the type of role that a unit plays in the operation. Finally, we explore how different network properties affect top-down control and processing in large networks. Based on this, we make predictions about the likely connectivities between certain brain regions that have been experimentally observed to be involved in goal-directed behavior and top-down attention. PMID:25152715

APPLICATION AND EVALUATION OF CMAQ IN THE UNITED STATES: AIR QUALITY FORECASTING AND RETROSPECTIVE MODELING

EPA Science Inventory

Presentation slides provide background on model evaluation techniques. Also included in the presentation is an operational evaluation of 2001 Community Multiscale Air Quality (CMAQ) annual simulation, and an evaluation of PM_2.5 for the CMAQ air quality forecast (AQF) ...

Performance Characteristics of Automotive Engines in the United States : Report No. 7. Mercedes Benz Model OM617 Diesel Engine.

DOT National Transportation Integrated Search

1977-01-01

Experimental data were obtained in dynamometer tests of the Mercedes Benz Model OM617 diesel engine to determine fuel consumption and emissions (hydrocarbon, carbon monoxide, oxides of nitroge, and smoke) at steady-state engine-operating modes. The o...

Performance Characteristics of Automotive Engines in the United States : Report No. 8. Mitsubishi Model 6DS7 Diesel Engine.

DOT National Transportation Integrated Search

1977-08-01

Experimental data were obtained in dynamometer tests of the Mitsubishi Model 6DS7 diesel engine to determine fuel consumption and emissions (hydrocarbon, carbon monoxide, oxides of nitrogen, and smoke) at steady-state engine operating modes. The obje...

40 CFR 60.2675 - What operating limits must I meet and by when?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Emission Limitations... electronic submission of the test report must also include the make and model of the PM CPMS instrument...

40 CFR 60.2675 - What operating limits must I meet and by when?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Emission Limitations... electronic submission of the test report must also include the make and model of the PM CPMS instrument...

Modeling Sound as a Non-Lethal Weapon in the COMBAT(XXI) Simulation Model

DTIC Science & Technology

2005-06-01

Kilgore in ‘ Apocalypse Now !’ [Ref 4] blasting Wagner from his Cavalry helicopters. Moving from film to recent history, consider how General Noriega...Military Operations Research Society, 71 4. Coppola, F. F. (Producer). (1979). Apocalypse now . [Motion Picture] Hollywood, California: United Artists

Advanced network planning for bus rapid transit : the "Quickway" model as a modal alternative to "Light Rail Lite"

DOT National Transportation Integrated Search

2008-02-01

Transit planning in the United States has tended toward viewing BRT as an analogue to light rail transit, with similar operating patterns. This model, referred to as Light Rail Lite, is compared to international best practices, which have often...

Los Angeles County Parks and Recreation.

ERIC Educational Resources Information Center

Iowa Univ., Iowa City. Recreation Education Program.

Presented are duplications of the responses given by the Los Angeles County Parks and Recreation Rehabilitation Unit (California) as part of a project to collect, share, and compile information about, and techniques in the operation of 18 community action models for recreation services to the disabled. Model programs are categorized as consumer,…

Improving Deterministic Reserve Requirements for Security Constrained Unit Commitment and Scheduling Problems in Power Systems

NASA Astrophysics Data System (ADS)

Wang, Fengyu

Traditional deterministic reserve requirements rely on ad-hoc, rule of thumb methods to determine adequate reserve in order to ensure a reliable unit commitment. Since congestion and uncertainties exist in the system, both the quantity and the location of reserves are essential to ensure system reliability and market efficiency. The modeling of operating reserves in the existing deterministic reserve requirements acquire the operating reserves on a zonal basis and do not fully capture the impact of congestion. The purpose of a reserve zone is to ensure that operating reserves are spread across the network. Operating reserves are shared inside each reserve zone, but intra-zonal congestion may block the deliverability of operating reserves within a zone. Thus, improving reserve policies such as reserve zones may improve the location and deliverability of reserve. As more non-dispatchable renewable resources are integrated into the grid, it will become increasingly difficult to predict the transfer capabilities and the network congestion. At the same time, renewable resources require operators to acquire more operating reserves. With existing deterministic reserve requirements unable to ensure optimal reserve locations, the importance of reserve location and reserve deliverability will increase. While stochastic programming can be used to determine reserve by explicitly modelling uncertainties, there are still scalability as well as pricing issues. Therefore, new methods to improve existing deterministic reserve requirements are desired. One key barrier of improving existing deterministic reserve requirements is its potential market impacts. A metric, quality of service, is proposed in this thesis to evaluate the price signal and market impacts of proposed hourly reserve zones. Three main goals of this thesis are: 1) to develop a theoretical and mathematical model to better locate reserve while maintaining the deterministic unit commitment and economic dispatch structure, especially with the consideration of renewables, 2) to develop a market settlement scheme of proposed dynamic reserve policies such that the market efficiency is improved, 3) to evaluate the market impacts and price signal of the proposed dynamic reserve policies.

Development of process control capability through the Browns Ferry Integrated Computer System using Reactor Water Clanup System as an example. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, J.; Mowrey, J.

1995-12-01

This report describes the design, development and testing of process controls for selected system operations in the Browns Ferry Nuclear Plant (BFNP) Reactor Water Cleanup System (RWCU) using a Computer Simulation Platform which simulates the RWCU System and the BFNP Integrated Computer System (ICS). This system was designed to demonstrate the feasibility of the soft control (video touch screen) of nuclear plant systems through an operator console. The BFNP Integrated Computer System, which has recently. been installed at BFNP Unit 2, was simulated to allow for operator control functions of the modeled RWCU system. The BFNP Unit 2 RWCU systemmore » was simulated using the RELAP5 Thermal/Hydraulic Simulation Model, which provided the steady-state and transient RWCU process variables and simulated the response of the system to control system inputs. Descriptions of the hardware and software developed are also included in this report. The testing and acceptance program and results are also detailed in this report. A discussion of potential installation of an actual RWCU process control system in BFNP Unit 2 is included. Finally, this report contains a section on industry issues associated with installation of process control systems in nuclear power plants.« less

Cotton gin trash in the western United States: Resource inventory and energy conversion characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haase, S.G.; Quinn, M.W.; Whittier, J.P.

1993-12-31

The disposal of wastes associated with the processing of cotton is posing increasing problems for cotton gin operators in the western United States. Traditional disposal methods, such as open-air incineration and landfilling are no longer adequate due to increasing environmental concerns. This paper evaluates the technical, economic and environmental feasibility for cotton gin trash to serve as an energy resource. Cotton gin trash has been quantified, by county, in the five cotton-growing states of the western United States. The energy conversion technology that appears to offer the most promise is gasification. An economic evaluation model has been developed that willmore » allow gin operators to analyze their own situation to determine the profitability of converting gin trash to energy.« less

Failure Analysis of Nonvolatile Residue (NVR) Analyzer Model SP-1000

NASA Technical Reports Server (NTRS)

Potter, Joseph C.

2011-01-01

National Aeronautics and Space Administration (NASA) subcontractor Wiltech contacted the NASA Electrical Lab (NE-L) and requested a failure analysis of a Solvent Purity Meter; model SP-IOOO produced by the VerTis Instrument Company. The meter, used to measure the contaminate in a solvent to determine the relative contamination on spacecraft flight hardware and ground servicing equipment, had been inoperable and in storage for an unknown amount of time. NE-L was asked to troubleshoot the unit and make a determination on what may be required to make the unit operational. Through the use of general troubleshooting processes and the review of a unit in service at the time of analysis, the unit was found to be repairable but would need the replacement of multiple components.

Discrete event simulation model for external yard choice of import container terminal in a port buffer area

NASA Astrophysics Data System (ADS)

Rusgiyarto, Ferry; Sjafruddin, Ade; Frazila, Russ Bona; Suprayogi

2017-06-01

Increasing container traffic and land acquisition problem for terminal expansion leads to usage of external yard in a port buffer area. This condition influenced the terminal performance because a road which connects the terminal and the external yard was also used by non-container traffic. Location choice problem considered to solve this condition, but the previous research has not taken account a stochastic condition of container arrival rate and service time yet. Bi-level programming framework was used to find optimum location configuration. In the lower-level, there was a problem to construct the equation, which correlated the terminal operation and the road due to different time cycle equilibrium. Container moves from the quay to a terminal gate in a daily unit of time, meanwhile, it moves from the terminal gate to the external yard through the road in a minute unit of time. If the equation formulated in hourly unit equilibrium, it cannot catch up the container movement characteristics in the terminal. Meanwhile, if the equation formulated in daily unit equilibrium, it cannot catch up the road traffic movement characteristics in the road. This problem can be addressed using simulation model. Discrete Event Simulation Model was used to simulate import container flow processes in the container terminal and external yard. Optimum location configuration in the upper-level was the combinatorial problem, which was solved by Full Enumeration approach. The objective function of the external yard location model was to minimize user transport cost (or time) and to maximize operator benefit. Numerical experiment was run for the scenario assumption of two container handling ways, three external yards, and thirty-day simulation periods. Jakarta International Container Terminal (JICT) container characteristics data was referred for the simulation. Based on five runs which were 5, 10, 15, 20, and 30 repetitions, operation one of three available external yards (external yard - 3) was the optimum result. Apparently, the model confirmed the hypothesis that there was an optimum configuration of the external yard. Nevertheless, the model needs detail elaboration related to the objective function and the optimization constraint. It requires detail validation, in term of service time value, distribution pattern, and arrival rate in each unit server modeled in the next step of the research. The model gave unique and relatively consistent value of each run. It was indicated that the method has a chance to solve the research problem.

System Testing of Ground Cooling System Components

NASA Technical Reports Server (NTRS)

Ensey, Tyler Steven

2014-01-01

This internship focused primarily upon software unit testing of Ground Cooling System (GCS) components, one of the three types of tests (unit, integrated, and COTS/regression) utilized in software verification. Unit tests are used to test the software of necessary components before it is implemented into the hardware. A unit test determines that the control data, usage procedures, and operating procedures of a particular component are tested to determine if the program is fit for use. Three different files are used to make and complete an efficient unit test. These files include the following: Model Test file (.mdl), Simulink SystemTest (.test), and autotest (.m). The Model Test file includes the component that is being tested with the appropriate Discrete Physical Interface (DPI) for testing. The Simulink SystemTest is a program used to test all of the requirements of the component. The autotest tests that the component passes Model Advisor and System Testing, and puts the results into proper files. Once unit testing is completed on the GCS components they can then be implemented into the GCS Schematic and the software of the GCS model as a whole can be tested using integrated testing. Unit testing is a critical part of software verification; it allows for the testing of more basic components before a model of higher fidelity is tested, making the process of testing flow in an orderly manner.

[Integration of a psychologist into Nephrology-Dialysis-Hypertension Operative Unit: from needs evaluation to the definition of an intervention model].

PubMed

Monica, Ratti Maria; Delli Zotti, Giulia Bruna; Spotti, Donatella; Sarno, Lucio

2014-01-01

Chronic Kidney Disease (CKD) and the dialytic treatment cause a significant psychological impact on patients, their families and on the medical-nursing staff too. The psychological aspects linked to the chronic condition of Kidney Disease generate the need to integrated a psychologist into the healthcare team of the Nephrology, Dialysis and Hypertension Operative Unit, in order to offer a specific and professional support to the patient during the different stages of the disease, to their caregivers and to the medical team. The aim of this collaboration project between Nephrology and Psychology is to create a global and integrated healthcare model. It does not give attention simply to the physical dimension of patients affected by CKD, but also to the emotional-affective, cognitive and social dimensions and to the health environment.

Wind Tunnel Management and Resource Optimization: A Systems Modeling Approach

NASA Technical Reports Server (NTRS)

Jacobs, Derya, A.; Aasen, Curtis A.

2000-01-01

Time, money, and, personnel are becoming increasingly scarce resources within government agencies due to a reduction in funding and the desire to demonstrate responsible economic efficiency. The ability of an organization to plan and schedule resources effectively can provide the necessary leverage to improve productivity, provide continuous support to all projects, and insure flexibility in a rapidly changing environment. Without adequate internal controls the organization is forced to rely on external support, waste precious resources, and risk an inefficient response to change. Management systems must be developed and applied that strive to maximize the utility of existing resources in order to achieve the goal of "faster, cheaper, better". An area of concern within NASA Langley Research Center was the scheduling, planning, and resource management of the Wind Tunnel Enterprise operations. Nine wind tunnels make up the Enterprise. Prior to this research, these wind tunnel groups did not employ a rigorous or standardized management planning system. In addition, each wind tunnel unit operated from a position of autonomy, with little coordination of clients, resources, or project control. For operating and planning purposes, each wind tunnel operating unit must balance inputs from a variety of sources. Although each unit is managed by individual Facility Operations groups, other stakeholders influence wind tunnel operations. These groups include, for example, the various researchers and clients who use the facility, the Facility System Engineering Division (FSED) tasked with wind tunnel repair and upgrade, the Langley Research Center (LaRC) Fabrication (FAB) group which fabricates repair parts and provides test model upkeep, the NASA and LARC Strategic Plans, and unscheduled use of the facilities by important clients. Expanding these influences horizontally through nine wind tunnel operations and vertically along the NASA management structure greatly increases the complexity of developing a model that can be used for successfully implementing a standardized management planning tool. The objective of this study was to implement an Integrated Wind Tunnel Planning System to improve the operations within the aeronautics testing and research group, in particular Wind Tunnel Enterprise. The study included following steps: Conducted literature search and expert discussions (NASA and Old Dominion University faculty), Performed environmental scan of NASA Langley wind tunnel operations as foundation for problem definition. Established operation requirements and evaluation methodologies. Examined windtunnel operations to map out the common characteristics, critical components, and system structure. Reviewed and evaluated various project scheduling and management systems for implementation, Evaluated and implemented "Theory of Constraints (TOC)" project scheduling methodology at NASA Langley wind tunnel operations together with NASA staff.

A simplified economic filter for open-pit mining and heap-leach recovery of copper in the United States

USGS Publications Warehouse

Long, Keith R.; Singer, Donald A.

2001-01-01

Determining the economic viability of mineral deposits of various sizes and grades is a critical task in all phases of mineral supply, from land-use management to mine development. This study evaluates two simple tools for estimating the economic viability of porphyry copper deposits mined by open-pit, heap-leach methods when only limited information on these deposits is available. These two methods are useful for evaluating deposits that either (1) are undiscovered deposits predicted by a mineral resource assessment, or (2) have been discovered but for which little data has been collected or released. The first tool uses ordinary least-squared regression analysis of cost and operating data from selected deposits to estimate a predictive relationship between mining rate, itself estimated from deposit size, and capital and operating costs. The second method uses cost models developed by the U.S. Bureau of Mines (Camm, 1991) updated using appropriate cost indices. We find that the cost model method works best for estimating capital costs and the empirical model works best for estimating operating costs for mines to be developed in the United States.

The Role of Short-Term Memory in Operator Workload

DTIC Science & Technology

1988-04-01

Craik , F.I. and Lockhart , R.S., 1972, Levels of processing : A framework for memory research...examples of postcategorical selction models. Precategorical Selection Models Sperling’s Model. Unlike Craik and Lockhart’s levels -of- processing model...subdivided to contain a primary memory unit and a mechanism for the direction of conscious attention. Levels -of- Processing . Craik and Lockhart’s levels

Experimentally validated finite element model of electrocaloric multilayer ceramic structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, N. A. S., E-mail: nadia.smith@npl.co.uk, E-mail: maciej.rokosz@npl.co.uk, E-mail: tatiana.correia@npl.co.uk; Correia, T. M., E-mail: nadia.smith@npl.co.uk, E-mail: maciej.rokosz@npl.co.uk, E-mail: tatiana.correia@npl.co.uk; Rokosz, M. K., E-mail: nadia.smith@npl.co.uk, E-mail: maciej.rokosz@npl.co.uk, E-mail: tatiana.correia@npl.co.uk

2014-07-28

A novel finite element model to simulate the electrocaloric response of a multilayer ceramic capacitor (MLCC) under real environment and operational conditions has been developed. The two-dimensional transient conductive heat transfer model presented includes the electrocaloric effect as a source term, as well as accounting for radiative and convective effects. The model has been validated with experimental data obtained from the direct imaging of MLCC transient temperature variation under application of an electric field. The good agreement between simulated and experimental data, suggests that the novel experimental direct measurement methodology and the finite element model could be used to supportmore » the design of optimised electrocaloric units and operating conditions.« less

Proton decay and light sterile neutrinos

NASA Astrophysics Data System (ADS)

Helo, Juan C.; Hirsch, Martin; Ota, Toshihiko

2018-06-01

Within the standard model, non-renormalizable operators at dimension six ( d = 6) violate baryon and lepton number by one unit and thus lead to proton decay. Here, we point out that the proton decay mode with a charged pion and missing energy can be a characteristic signature of d = 6 operators containing a light sterile neutrino, if it is not accompanied by the standard π0 e + final state. We discuss this effect first at the level of effective operators and then provide a concrete model with new physics at the TeV scale, in which the lightness of the active neutrinos and the stability of the proton are related.

Continuous state-space representation of a bucket-type rainfall-runoff model: a case study with the GR4 model using state-space GR4 (version 1.0)

NASA Astrophysics Data System (ADS)

Santos, Léonard; Thirel, Guillaume; Perrin, Charles

2018-04-01

In many conceptual rainfall-runoff models, the water balance differential equations are not explicitly formulated. These differential equations are solved sequentially by splitting the equations into terms that can be solved analytically with a technique called operator splitting. As a result, only the solutions of the split equations are used to present the different models. This article provides a methodology to make the governing water balance equations of a bucket-type rainfall-runoff model explicit and to solve them continuously. This is done by setting up a comprehensive state-space representation of the model. By representing it in this way, the operator splitting, which makes the structural analysis of the model more complex, could be removed. In this state-space representation, the lag functions (unit hydrographs), which are frequent in rainfall-runoff models and make the resolution of the representation difficult, are first replaced by a so-called Nash cascade and then solved with a robust numerical integration technique. To illustrate this methodology, the GR4J model is taken as an example. The substitution of the unit hydrographs with a Nash cascade, even if it modifies the model behaviour when solved using operator splitting, does not modify it when the state-space representation is solved using an implicit integration technique. Indeed, the flow time series simulated by the new representation of the model are very similar to those simulated by the classic model. The use of a robust numerical technique that approximates a continuous-time model also improves the lag parameter consistency across time steps and provides a more time-consistent model with time-independent parameters.

Real-time co-simulation of adjustable-speed pumped storage hydro for transient stability analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohanpurkar, Manish; Ouroua, Abdelhamid; Hovsapian, Rob

Pumped storage hydro (PSH) based generation of electricity is a proven grid level storage technique. A new configuration i.e., adjustable speed PSH (AS-PSH) power plant is modeled and discussed in this paper. Hydrodynamic models are created using partial differential equations and the governor topology adopted from an existing, operational AS-PSH unit. Physics-based simulation of both hydrodynamics and power system dynamics has been studied individually in the past. This article demonstrates a co-simulation of an AS-PSH unit between penstock hydrodynamics and power system events in a real-time environment. Co-simulation provides an insight into the dynamic and transient operation of AS-PSH connectedmore » to a bulk power system network. The two modes of AS-PSH operation presented in this paper are turbine and pump modes. A general philosophy of operating in turbine mode is prevalent in the field when the prices of electricity are high and in the pumping mode when prices are low. However, recently there is renewed interest in operating PSH to also provide ancillary services. A real-time co-simulation at sub-second regime of AS-PSH connected to the IEEE 14 bus test system is performed using digital real-time simulator and the results are discussed.« less

Real-time co-simulation of adjustable-speed pumped storage hydro for transient stability analysis

DOE PAGES

Mohanpurkar, Manish; Ouroua, Abdelhamid; Hovsapian, Rob; ...

2017-09-12

Pumped storage hydro (PSH) based generation of electricity is a proven grid level storage technique. A new configuration i.e., adjustable speed PSH (AS-PSH) power plant is modeled and discussed in this paper. Hydrodynamic models are created using partial differential equations and the governor topology adopted from an existing, operational AS-PSH unit. Physics-based simulation of both hydrodynamics and power system dynamics has been studied individually in the past. This article demonstrates a co-simulation of an AS-PSH unit between penstock hydrodynamics and power system events in a real-time environment. Co-simulation provides an insight into the dynamic and transient operation of AS-PSH connectedmore » to a bulk power system network. The two modes of AS-PSH operation presented in this paper are turbine and pump modes. A general philosophy of operating in turbine mode is prevalent in the field when the prices of electricity are high and in the pumping mode when prices are low. However, recently there is renewed interest in operating PSH to also provide ancillary services. A real-time co-simulation at sub-second regime of AS-PSH connected to the IEEE 14 bus test system is performed using digital real-time simulator and the results are discussed.« less

Tube structural integrity evaluation of Palo Verde Unit 1 steam generators for axial upper-bundle cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodman, B.W.; Begley, J.A.; Brown, S.D.

1995-12-01

The analysis of the issue of upper bundle axial ODSCC as it apples to steam generator tube structural integrity in Unit 1 at the Palo Verde Nuclear generating Station is presented in this study. Based on past inspection results for Units 2 and 3 at Palo Verde, the detection of secondary side stress corrosion cracks in the upper bundle region of Unit 1 may occur at some future date. The following discussion provides a description and analysis of the probability of axial ODSCC in Unit 1 leading to the exceedance of Regulatory Guide 1.121 structural limits. The probabilities of structuralmore » limit exceedance are estimated as function of run time using a conservative approach. The chosen approach models the historical development of cracks, crack growth, detection of cracks and subsequent removal from service and the initiation and growth of new cracks during a given cycle of operation. Past performance of all Palo Verde Units as well as the historical performance of other steam generators was considered in the development of cracking statistics for application to Unit 1. Data in the literature and Unit 2 pulled tube examination results were used to construct probability of detection curves for the detection of axial IGSCC/IGA using an MRPC (multi-frequency rotating panake coil) eddy current probe. Crack growth rates were estimated from Unit 2 eddy current inspection data combined with pulled tube examination results and data in the literature. A Monte-Carlo probabilistic model is developed to provide an overall assessment of the risk of Regulatory Guide exceedance during plant operation.« less

Development and Application of a Life Cycle-Based Model to Evaluate Greenhouse Gas Emissions of Oil Sands Upgrading Technologies.

PubMed

Pacheco, Diana M; Bergerson, Joule A; Alvarez-Majmutov, Anton; Chen, Jinwen; MacLean, Heather L

2016-12-20

A life cycle-based model, OSTUM (Oil Sands Technologies for Upgrading Model), which evaluates the energy intensity and greenhouse gas (GHG) emissions of current oil sands upgrading technologies, is developed. Upgrading converts oil sands bitumen into high quality synthetic crude oil (SCO), a refinery feedstock. OSTUM's novel attributes include the following: the breadth of technologies and upgrading operations options that can be analyzed, energy intensity and GHG emissions being estimated at the process unit level, it not being dependent on a proprietary process simulator, and use of publicly available data. OSTUM is applied to a hypothetical, but realistic, upgrading operation based on delayed coking, the most common upgrading technology, resulting in emissions of 328 kg CO 2 e/m 3 SCO. The primary contributor to upgrading emissions (45%) is the use of natural gas for hydrogen production through steam methane reforming, followed by the use of natural gas as fuel in the rest of the process units' heaters (39%). OSTUM's results are in agreement with those of a process simulation model developed by CanmetENERGY, other literature, and confidential data of a commercial upgrading operation. For the application of the model, emissions are found to be most sensitive to the amount of natural gas utilized as feedstock by the steam methane reformer. OSTUM is capable of evaluating the impact of different technologies, feedstock qualities, operating conditions, and fuel mixes on upgrading emissions, and its life cycle perspective allows easy incorporation of results into well-to-wheel analyses.

Fighting The Network: Manet Management In Support Of Littoral Operations

DTIC Science & Technology

2016-03-01

Solomon , 2015). DL widens the scope of naval Surface Action Groups (SAG) operations, introducing the concept of Adaptive Force Package (AFP...be implemented in littoral tactical networks. CENETIX research utilizes three Wave Relay radio models for experimentation : the Man-Portable Unit...enable seamless continuity in the transfer of research knowledge to subsequent testing and CONOPS development. CENETIX field experimentation

Software Cost Estimating,

DTIC Science & Technology

1982-05-13

Size Of The Software. A favourite measure for software system size is linos of operational code, or deliverable code (operational code plus...regression models, these conversions are either derived from productivity measures using the "cost per instruction" type of equation or they are...appropriate to different development organisattons, differert project types, different sets of units for measuring e and s, and different items

Quantum Computation Using Optically Coupled Quantum Dot Arrays

NASA Technical Reports Server (NTRS)

Pradhan, Prabhakar; Anantram, M. P.; Wang, K. L.; Roychowhury, V. P.; Saini, Subhash (Technical Monitor)

1998-01-01

A solid state model for quantum computation has potential advantages in terms of the ease of fabrication, characterization, and integration. The fundamental requirements for a quantum computer involve the realization of basic processing units (qubits), and a scheme for controlled switching and coupling among the qubits, which enables one to perform controlled operations on qubits. We propose a model for quantum computation based on optically coupled quantum dot arrays, which is computationally similar to the atomic model proposed by Cirac and Zoller. In this model, individual qubits are comprised of two coupled quantum dots, and an array of these basic units is placed in an optical cavity. Switching among the states of the individual units is done by controlled laser pulses via near field interaction using the NSOM technology. Controlled rotations involving two or more qubits are performed via common cavity mode photon. We have calculated critical times, including the spontaneous emission and switching times, and show that they are comparable to the best times projected for other proposed models of quantum computation. We have also shown the feasibility of accessing individual quantum dots using the NSOM technology by calculating the photon density at the tip, and estimating the power necessary to perform the basic controlled operations. We are currently in the process of estimating the decoherence times for this system; however, we have formulated initial arguments which seem to indicate that the decoherence times will be comparable, if not longer, than many other proposed models.

The Building Blocks for JWST I and T (Integrations and Test) to Operations - From Simulator to Flight Units

NASA Technical Reports Server (NTRS)

Fatig, Curtis; Ochs, William; Johns, Alan; Seaton, Bonita; Adams, Cynthia; Wasiak, Francis; Jones, Ronald; Jackson, Wallace

2012-01-01

The James Webb Space Telescope (JWST) Project has an extended integration and test (I&T) phase due to long procurement and development times of various components as well as recent launch delays. The JWST Ground Segment and Operations group has developed a roadmap of the various ground and flight elements and their use in the various JWST I&T test programs. The JWST Project s building block approach to the eventual operational systems, while not new, is complex and challenging; a large-scale mission like JWST involves international partners, many vendors across the United States, and competing needs for the same systems. One of the challenges is resource balancing so simulators and flight products for various elements congeal into integrated systems used for I&T and flight operations activities. This building block approach to an incremental buildup provides for early problem identification with simulators and exercises the flight operations systems, products, and interfaces during the JWST I&T test programs. The JWST Project has completed some early I&T with the simulators, engineering models and some components of the operational ground system. The JWST Project is testing the various flight units as they are delivered and will continue to do so for the entire flight and operational system. The JWST Project has already and will continue to reap the value of the building block approach on the road to launch and flight operations.

Unit mechanisms of fission gas release: Current understanding and future needs

DOE PAGES

Tonks, Michael; Andersson, David; Devanathan, Ram; ...

2018-03-01

Gaseous fission product transport and release has a large impact on fuel performance, degrading fuel and gap properties. While gaseous fission product behavior has been investigated with bulk reactor experiments and simplified analytical models, recent improvements in experimental and modeling approaches at the atomistic and mesoscales are beginning to reveal new understanding of the unit mechanisms that define fission product behavior. Here, existing research on the basic mechanisms of fission gas release during normal reactor operation are summarized and critical areas where work is needed are identified. Here, this basic understanding of the fission gas behavior mechanisms has the potentialmore » to revolutionize our ability to predict fission product behavior and to design fuels with improved performance. In addition, this work can serve as a model on how a coupled experimental and modeling approach can be applied to understand the unit mechanisms behind other critical behaviors in reactor materials.« less

Unit mechanisms of fission gas release: Current understanding and future needs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tonks, Michael; Andersson, David; Devanathan, Ram

Gaseous fission product transport and release has a large impact on fuel performance, degrading fuel and gap properties. While gaseous fission product behavior has been investigated with bulk reactor experiments and simplified analytical models, recent improvements in experimental and modeling approaches at the atomistic and mesoscales are beginning to reveal new understanding of the unit mechanisms that define fission product behavior. Here, existing research on the basic mechanisms of fission gas release during normal reactor operation are summarized and critical areas where work is needed are identified. Here, this basic understanding of the fission gas behavior mechanisms has the potentialmore » to revolutionize our ability to predict fission product behavior and to design fuels with improved performance. In addition, this work can serve as a model on how a coupled experimental and modeling approach can be applied to understand the unit mechanisms behind other critical behaviors in reactor materials.« less

Unit mechanisms of fission gas release: Current understanding and future needs

NASA Astrophysics Data System (ADS)

Tonks, Michael; Andersson, David; Devanathan, Ram; Dubourg, Roland; El-Azab, Anter; Freyss, Michel; Iglesias, Fernando; Kulacsy, Katalin; Pastore, Giovanni; Phillpot, Simon R.; Welland, Michael

2018-06-01

Gaseous fission product transport and release has a large impact on fuel performance, degrading fuel and gap properties. While gaseous fission product behavior has been investigated with bulk reactor experiments and simplified analytical models, recent improvements in experimental and modeling approaches at the atomistic and mesoscales are beginning to reveal new understanding of the unit mechanisms that define fission product behavior. Here, existing research on the basic mechanisms of fission gas release during normal reactor operation are summarized and critical areas where work is needed are identified. This basic understanding of the fission gas behavior mechanisms has the potential to revolutionize our ability to predict fission product behavior and to design fuels with improved performance. In addition, this work can serve as a model on how a coupled experimental and modeling approach can be applied to understand the unit mechanisms behind other critical behaviors in reactor materials.

Development of a Landforms Model for Puerto Rico and its Application for Land Cover Change Analysis

Treesearch

Sebastian Martinuzzi; William A. Gould; Olga M. Ramos Gonzalez; Brook E. Edwards

2007-01-01

Comprehensive analysis of land morphology is essential to supporting a wide range environmental studies. We developed a landforms model that identifies eleven landform units for Puerto Rico based on parameters of land position and slope. The model is capable of extracting operational information in a simple way and is adaptable to different environments and objectives...

Development and Testing of a Fully Adaptable Membrane Bioreactor Fouling Model for a Sidestream Configuration System

PubMed Central

Paul, Parneet

2013-01-01

A dead-end filtration model that includes the three main fouling mechanisms mentioned in Hermia (i.e., cake build-up, complete pore blocking, and pore constriction) and that was based on a constant trans-membrane pressure (TMP) operation was extensively modified so it could be used for a sidestream configuration membrane bioreactor (MBR) situation. Modifications and add-ons to this basic model included: alteration so that it could be used for varying flux and varying TMP operations; inclusion of a backwash mode; it described pore constriction (i.e., irreversible fouling) in relation to the concentration of soluble microbial products (SMP) in the liquor; and, it could be used in a cross flow scenario by the addition of scouring terms in the model formulation. The additional terms in this modified model were checked against an already published model to see if they made sense, physically speaking. Next this modified model was calibrated and validated in Matlab© using data collected by carrying out flux stepping tests on both a pilot sidestream MBR plant, and then a pilot membrane filtration unit. The model fit proved good, especially for the pilot filtration unit data. In conclusion, this model formulation is of the right level of complexity to be used for most practical MBR situations. PMID:24958618

Solar stills for agricultural purposes

NASA Technical Reports Server (NTRS)

Selcuk, M. K.; Tran, V. V.

1975-01-01

Basic concepts of using desalinated water for agricultural purposes are outlined. A mathematical model describing heat and mass transfer in a system combining a solar still with a greenhouse, its solution, and test results of a small-scale unit built at the Middle East Technical University, Ankara, Turkey, are discussed. The unit was employed to demonstrate the technical feasibility of the system. Further development and modifications are necessary for larger-scale operations. The basis of an optimization study which is underway at the Brace Research Institute of McGill University in Montreal, Canada, aimed at finding the best combination of design and operation parameters is also presented.

40 CFR 60.2070 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... requirements? (a) No CISWI unit can be operated unless a fully trained and qualified CISWI unit operator is... unit operator may operate the CISWI unit directly or be the direct supervisor of one or more other...

An explicit asymptotic model for the surface wave in a viscoelastic half-space based on applying Rabotnov's fractional exponential integral operators

NASA Astrophysics Data System (ADS)

Wilde, M. V.; Sergeeva, N. V.

2018-05-01

An explicit asymptotic model extracting the contribution of a surface wave to the dynamic response of a viscoelastic half-space is derived. Fractional exponential Rabotnov's integral operators are used for describing of material properties. The model is derived by extracting the principal part of the poles corresponding to the surface waves after applying Laplace and Fourier transforms. The simplified equations for the originals are written by using power series expansions. Padè approximation is constructed to unite short-time and long-time models. The form of this approximation allows to formulate the explicit model using a fractional exponential Rabotnov's integral operator with parameters depending on the properties of surface wave. The applicability of derived models is studied by comparing with the exact solutions of a model problem. It is revealed that the model based on Padè approximation is highly effective for all the possible time domains.

Separation of tartronic and glyceric acids by simulated moving bed chromatography.

PubMed

Coelho, Lucas C D; Filho, Nelson M L; Faria, Rui P V; Ferreira, Alexandre F P; Ribeiro, Ana M; Rodrigues, Alírio E

2018-08-17

The SMB unit developed by the Laboratory of Separation and Reaction Engineering (FlexSMB-LSRE ® ) was used to perform tartronic acid (TTA) and glyceric acid (GCA) separation and to validate the mathematical model in order to determine the optimum operating parameters of an industrial unit. The purity of the raffinate and extract streams in the experiments performed were 80% and 100%, respectively. The TTA and GCA productivities were 79 and 115 kg per liter of adsorbent per day, respectively and only 0.50 cubic meters of desorbent were required per kilogram of products. Under the optimum operating conditions, which were determined through an extensive simulation study based on the mathematical model developed to predict the performance of a real SMB unit, it was possible to achieve a productivity of 86 kg of TTA and 176 kg of GCA per cubic meter of adsorbent per day (considering the typical commercial purity value of 97% for both compounds) with an eluent consumption of 0.30 cubic meters per kilogram of products. Copyright © 2018 Elsevier B.V. All rights reserved.

Operability and Efficiency Performance of Ultra-Compact, High Gravity (g) Combustor Concepts (Postprint)

DTIC Science & Technology

2007-07-01

the U.S. Government and is not subject to copyright protection in the United States. PAO Case Number: AFRL/WS 05-1781, 23 Aug 2005. 14. ABSTRACT...significantly. Recent modeling by Katta10 where the Lewis9 experiment was modeled using UNICORN (Unsteady Ignition and Combustion using ReactioNs), a

Real-Time Bias-Adjusted O3 and PM2.5 Air Quality Index Forecasts and their Performance Evaluations over the Continental United States

EPA Science Inventory

The National Air Quality Forecast Capacity (NAQFC) system, which links NOAA's North American Mesoscale (NAM) meteorological model with EPA's Community Multiscale Air Quality (CMAQ) model, provided operational ozone (O₃) and experimental fine particular matter (PM_2...

The explosion at institute: modeling and analyzing the situation awareness factor.

PubMed

Naderpour, Mohsen; Lu, Jie; Zhang, Guangquan

2014-12-01

In 2008 a runaway chemical reaction caused an explosion at a methomyl unit in West Virginia, USA, killing two employees, injuring eight people, evacuating more than 40,000 residents adjacent to the facility, disrupting traffic on a nearby highway and causing significant business loss and interruption. Although the accident was formally investigated, the role of the situation awareness (SA) factor, i.e., a correct understanding of the situation, and appropriate models to maintain SA, remain unexplained. This paper extracts details of abnormal situations within the methomyl unit and models them into a situational network using dynamic Bayesian networks. A fuzzy logic system is used to resemble the operator's thinking when confronted with these abnormal situations. The combined situational network and fuzzy logic system make it possible for the operator to assess such situations dynamically to achieve accurate SA. The findings show that the proposed structure provides a useful graphical model that facilitates the inclusion of prior background knowledge and the updating of this knowledge when new information is available from monitoring systems. Copyright © 2014 Elsevier Ltd. All rights reserved.

Model for Assembly Line Re-Balancing Considering Additional Capacity and Outsourcing to Face Demand Fluctuations

NASA Astrophysics Data System (ADS)

Samadhi, TMAA; Sumihartati, Atin

2016-02-01

The most critical stage in a garment industry is sewing process, because generally, it consists of a number of operations and a large number of sewing machines for each operation. Therefore, it requires a balancing method that can assign task to work station with balance workloads. Many studies on assembly line balancing assume a new assembly line, but in reality, due to demand fluctuation and demand increased a re-balancing is needed. To cope with those fluctuating demand changes, additional capacity can be carried out by investing in spare sewing machine and paying for sewing service through outsourcing. This study develops an assembly line balancing (ALB) model on existing line to cope with fluctuating demand change. Capacity redesign is decided if the fluctuation demand exceeds the available capacity through a combination of making investment on new machines and outsourcing while considering for minimizing the cost of idle capacity in the future. The objective of the model is to minimize the total cost of the line assembly that consists of operating costs, machine cost, adding capacity cost, losses cost due to idle capacity and outsourcing costs. The model develop is based on an integer programming model. The model is tested for a set of data of one year demand with the existing number of sewing machines of 41 units. The result shows that additional maximum capacity up to 76 units of machine required when there is an increase of 60% of the average demand, at the equal cost parameters..

11 Years of experience in vitreoretinal surgery training in Nairobi, Kenya, from 2000 to 2010.

PubMed

Schönfeld, Carl-Ludwig; Kollmann, Martin; Nyaga, Patrick; Onyango, Oskar; Klauss, Volker; Kampik, Anselm

2013-08-01

We aim to demonstrate that vitreoretinal surgery can be established in Nairobi, Kenya, by intermittent short visits of experienced surgeons combined with clinical/surgical observerships over a longer period of cooperation. This strategy might be a model for other developing countries. Time series over 11 years. 685 operations were performed over 11 years. After the 1998 al-Qaeda bomb assault on the U.S. embassy in Nairobi, Kenya, the Ludwig-Maximilians-University München (Germany) provided materials for surgery of 42 victims with eye injuries. From the year 2000 onward, this equipment has been used to establish a training unit at the Kenyatta Hospital in Nairobi. In 1 annual "project week," 1 author (C-L.S.) performed vitreoretinal surgery at the University of Nairobi in cooperation with the Kenyatta National Hospital and supervised resident eye surgeons. After 7 years of training in Nairobi, clinical/surgical observerships of vitreoretinal surgeons and operating theatre staff were commenced in Munich by 4- to 12-week visits. The project week in Nairobi was carried on. Number, indications, operating surgeons, kind, difficulty, duration of operations, and preparation were recorded and evaluated. The percentage of operations by resident surgeons increased from 29% (in 2000) via 80% (in 2009) to 73% (in 2010) with a partial failure of the laser device. The learning curve of local surgeons is also reflected by an increase of the operations' difficulty with only a moderate increase in operation time and marked decrease of preparation time. A vitreoretinal unit has been established in Nairobi using our training model. This unit has the potential to train colleagues from other sub-Saharan countries. This strategy has advantages over long-term aid deployment of foreign physicians such as avoiding financial burden for the surgeons to be trained and improving the home facility, but it requires commitment for long-term cooperation. Copyright © 2013 Canadian Ophthalmological Society. Published by Elsevier Inc. All rights reserved.

Improvement of Steam Turbine Operational Performance and Reliability with using Modern Information Technologies

NASA Astrophysics Data System (ADS)

Brezgin, V. I.; Brodov, Yu M.; Kultishev, A. Yu

2017-11-01

The report presents improvement methods review in the fields of the steam turbine units design and operation based on modern information technologies application. In accordance with the life cycle methodology support, a conceptual model of the information support system during life cycle main stages (LC) of steam turbine unit is suggested. A classifying system, which ensures the creation of sustainable information links between the engineer team (manufacture’s plant) and customer organizations (power plants), is proposed. Within report, the principle of parameterization expansion beyond the geometric constructions at the design and improvement process of steam turbine unit equipment is proposed, studied and justified. The report presents the steam turbine unit equipment design methodology based on the brand new oil-cooler design system that have been developed and implemented by authors. This design system combines the construction subsystem, which is characterized by extensive usage of family tables and templates, and computation subsystem, which includes a methodology for the thermal-hydraulic zone-by-zone oil coolers design calculations. The report presents data about the developed software for operational monitoring, assessment of equipment parameters features as well as its implementation on five power plants.

Connectionist interpretation of the association between cognitive dissonance and attention switching.

PubMed

Matsumoto, Takao

2014-12-01

A novel connectionist model accounting for cognitive dissonance is described, in which the concepts of self and attention switching are considered. The model is composed of a unit corresponding to self, a bistable pair comprising two units relevant to two dissonant cognitions, and links whose weights correspond to cognitive evaluations. The model makes it possible to use mathematical formulas to represent the cognitive-dissonance process. Analysis reveals that the model fits experimental data of major paradigms in cognitive dissonance theory. The model shows that attention switching, which is produced by internal and external stimuli, causes building-up of cognitive dissonance and retardation of its reduction. The psychological phenomenon of selective exposure is interpreted on the basis of the operation of the model. Copyright © 2014 Elsevier Ltd. All rights reserved.

Identifying Electricity Capacity at Risk to Changes in Climate and Water Resources in the United States

NASA Astrophysics Data System (ADS)

Miara, A.; Macknick, J.; Vorosmarty, C. J.; Corsi, F.; Fekete, B. M.; Newmark, R. L.; Tidwell, V. C.; Cohen, S. M.

2016-12-01

Thermoelectric plants supply 85% of electricity generation in the United States. Under a warming climate, the performance of these power plants may be reduced, as thermoelectric generation is dependent upon cool ambient temperatures and sufficient water supplies at adequate temperatures. In this study, we assess the vulnerability and reliability of 1,100 operational power plants (2015) across the contiguous United States under a comprehensive set of climate scenarios (five Global Circulation Models each with four Representative Concentration Pathways). We model individual power plant capacities using the Thermoelectric Power and Thermal Pollution model (TP2M) coupled with the Water Balance Model (WBM) at a daily temporal resolution and 5x5 km spatial resolution. Together, these models calculate power plant capacity losses that account for geophysical constraints and river network dynamics. Potential losses at the single-plant level are put into a regional energy security context by assessing the collective system-level reliability at the North-American Electricity Reliability Corporation (NERC) regions. Results show that the thermoelectric sector at the national level has low vulnerability under the contemporary climate and that system-level reliability in terms of available thermoelectric resources relative to thermoelectric demand is sufficient. Under future climates scenarios, changes in water availability and warm ambient temperatures lead to constraints on operational capacity and increased vulnerability at individual power plant sites across all regions in the United States. However, there is a strong disparity in regional vulnerability trends and magnitudes that arise from each region's climate, hydrology and technology mix. Despite increases in vulnerabilities at the individual power plant level, regional energy systems may still be reliable (with no system failures) due to sufficient back-up reserve capacities.

Hydroelectric System Response to Part Load Vortex Rope Excitation

NASA Astrophysics Data System (ADS)

Alligné, S.; Nicolet, C.; Bégum, A.; Landry, C.; Gomes, J.; Avellan, F.

2016-11-01

The prediction of pressure and output power fluctuations amplitudes on Francis turbine prototype is a challenge for hydro-equipment industry since it is subjected to guarantees to ensure smooth and reliable operation of the hydro units. The European FP7 research project Hyperbole aims to setup a methodology to transpose the pressure fluctuations induced by the cavitation vortex rope on the reduced scale model to the prototype generating units. A Francis turbine unit of 444MW with a specific speed value of v = 0.29, is considered as case study. A SIMSEN model of the power station including electrical system, controllers, rotating train and hydraulic system with transposed draft tube excitation sources is setup. Based on this model, a frequency analysis of the hydroelectric system is performed to analyse potential interactions between hydraulic excitation sources and electrical components.

Superfund Record of Decision (EPA Region 6): Texarkana Wood Preserving Company, Operable Unit 2, Texarkana, TX, September 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This decision document presents the selected remedial action for Operable Unit Two for the Texarkana Wood Preserving Company (TWPC) Superfund Site (Site) in Texarkana, Texas. This operable unit is the second of two operable units planned for the Site. Operable Unit Two involves remediation of the deeper ground water contaminated above the action levels in a limited area of the Silty Sand Zone around Monitoring Well-16.

Integration issues of a plasma contactor Power Electronics Unit

NASA Technical Reports Server (NTRS)

Pinero, Luis R.; York, Kenneth W.; Bowers, Glen E.

1995-01-01

A hollow cathode-based plasma contactor is baselined on International Space Station Alpha (ISSA) for spacecraft charge control. The plasma contactor system consists of a hollow cathode assembly (HCA), a power electronics unit (PEU), and an expellant management unit (EMU). The plasma contactor has recently been required to operate in a cyclic mode to conserve xenon expellant and extend system life. Originally, a DC cathode heater converter was baselined for a continuous operation mode because only a few ignitions of the hollow cathode were expected. However, for cyclic operation, a DC heater supply can potentially result in hollow cathode heater component failure due to the DC electrostatic field. This can prevent the heater from attaining the proper cathode tip temperature for reliable ignition of the hollow cathode. To mitigate this problem, an AC cathode heater supply was therefore designed, fabricated, and installed into a modified PEU. The PEU was tested using resistive loads and then integrated with an engineering model hollow cathode to demonstrate stable steady-state operation. Integration issues such as the effect of line and load impedance on the output of the AC cathode heater supply and the characterization of the temperature profile of the heater under AC excitation were investigated.

Study on reservoir time-varying design flood of inflow based on Poisson process with time-dependent parameters

NASA Astrophysics Data System (ADS)

Li, Jiqing; Huang, Jing; Li, Jianchang

2018-06-01

The time-varying design flood can make full use of the measured data, which can provide the reservoir with the basis of both flood control and operation scheduling. This paper adopts peak over threshold method for flood sampling in unit periods and Poisson process with time-dependent parameters model for simulation of reservoirs time-varying design flood. Considering the relationship between the model parameters and hypothesis, this paper presents the over-threshold intensity, the fitting degree of Poisson distribution and the design flood parameters are the time-varying design flood unit period and threshold discriminant basis, deduced Longyangxia reservoir time-varying design flood process at 9 kinds of design frequencies. The time-varying design flood of inflow is closer to the reservoir actual inflow conditions, which can be used to adjust the operating water level in flood season and make plans for resource utilization of flood in the basin.

Nonlinear predictive control of a boiler-turbine unit: A state-space approach with successive on-line model linearisation and quadratic optimisation.

PubMed

Ławryńczuk, Maciej

2017-03-01

This paper details development of a Model Predictive Control (MPC) algorithm for a boiler-turbine unit, which is a nonlinear multiple-input multiple-output process. The control objective is to follow set-point changes imposed on two state (output) variables and to satisfy constraints imposed on three inputs and one output. In order to obtain a computationally efficient control scheme, the state-space model is successively linearised on-line for the current operating point and used for prediction. In consequence, the future control policy is easily calculated from a quadratic optimisation problem. For state estimation the extended Kalman filter is used. It is demonstrated that the MPC strategy based on constant linear models does not work satisfactorily for the boiler-turbine unit whereas the discussed algorithm with on-line successive model linearisation gives practically the same trajectories as the truly nonlinear MPC controller with nonlinear optimisation repeated at each sampling instant. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

21 CFR 872.6640 - Dental operative unit and accessories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dental operative unit and accessories. 872.6640... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6640 Dental operative unit and accessories. (a) Identification. A dental operative unit and accessories is an AC-powered device that is...

21 CFR 872.6640 - Dental operative unit and accessories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dental operative unit and accessories. 872.6640... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6640 Dental operative unit and accessories. (a) Identification. A dental operative unit and accessories is an AC-powered device that is...

21 CFR 872.6640 - Dental operative unit and accessories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dental operative unit and accessories. 872.6640... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6640 Dental operative unit and accessories. (a) Identification. A dental operative unit and accessories is an AC-powered device that is...

21 CFR 872.6640 - Dental operative unit and accessories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dental operative unit and accessories. 872.6640... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6640 Dental operative unit and accessories. (a) Identification. A dental operative unit and accessories is an AC-powered device that is...

21 CFR 872.6640 - Dental operative unit and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental operative unit and accessories. 872.6640... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6640 Dental operative unit and accessories. (a) Identification. A dental operative unit and accessories is an AC-powered device that is...

A Petri-net coordination model for an intelligent mobile robot

NASA Technical Reports Server (NTRS)

Wang, F.-Y.; Kyriakopoulos, K. J.; Tsolkas, A.; Saridis, G. N.

1990-01-01

The authors present a Petri net model of the coordination level of an intelligent mobile robot system (IMRS). The purpose of this model is to specify the integration of the individual efforts on path planning, supervisory motion control, and vision systems that are necessary for the autonomous operation of the mobile robot in a structured dynamic environment. This is achieved by analytically modeling the various units of the system as Petri net transducers and explicitly representing the task precedence and information dependence among them. The model can also be used to simulate the task processing and to evaluate the efficiency of operations and the responsibility of decisions in the coordination level of the IMRS. Some simulation results on the task processing and learning are presented.

Reduced Order Adaptive Controllers for Distributed Parameter Systems

DTIC Science & Technology

2005-09-01

pitch moment [J313. Neural Network adaptive output feedback control for intensive care unit sedation and intraop- erative anesthesia . Neural network...depth of anesthesia for noncardiac surgery [C3, J15]. These results present an extension of [C8, J9, J10]. Modelling and vibration control of...for Intensive Care Unit Sedation and Operating Room Hypnosis , Submitted to 6 Special Issue of SIAM Journal of Control and Optimization on Control

Effectiveness of Prepared Instruction Units in Teaching the Principles of Internal Combustion Engine Operation and Maintenance. Technical Bulletin No. 192.

ERIC Educational Resources Information Center

Jacobs, Clinton O.

The report is an evaluation of the effectiveness of the 12 instructional units developed around the use of the Briggs-Stratton Model 80302, 3HP, 8 cu. in. displacement engine having a fuel induction system similar in construction to farm tractor types. The evaluation procedure used was the "one-group Pre-test and Post-test" research method. The…

Mobile Food Ordering Application using Android OS Platform

NASA Astrophysics Data System (ADS)

Yosep Ricky, Michael

2014-03-01

The purpose of this research is making an ordering food application based on Android with New Order, Order History, Restaurant Profile, Order Status, Tracking Order, and Setting Profile features. The research method used in this research is water model of System Development Life Cycle (SDLC) method with following phases: requirement definition, analyzing and determining the features needed in developing application and making the detail definition of each features, system and software design, designing the flow of developing application by using storyboard design, user experience design, Unified Modeling Language (UML) design, and database structure design, implementation an unit testing, making database and translating the result of designs to programming language code then doing unit testing, integration and System testing, integrating unit program to one unit system then doing system testing, operation and maintenance, operating the result of system testing and if any changes and reparations needed then the previous phases could be back. The result of this research is an ordering food application based on Android for customer and courier user, and a website for restaurant and admin user. The conclusion of this research is to help customer in making order easily, to give detail information needed by customer, to help restaurant in receiving order, and to help courier while doing delivery.

Real-time three-dimensional soft tissue reconstruction for laparoscopic surgery.

PubMed

Kowalczuk, Jędrzej; Meyer, Avishai; Carlson, Jay; Psota, Eric T; Buettner, Shelby; Pérez, Lance C; Farritor, Shane M; Oleynikov, Dmitry

2012-12-01

Accurate real-time 3D models of the operating field have the potential to enable augmented reality for endoscopic surgery. A new system is proposed to create real-time 3D models of the operating field that uses a custom miniaturized stereoscopic video camera attached to a laparoscope and an image-based reconstruction algorithm implemented on a graphics processing unit (GPU). The proposed system was evaluated in a porcine model that approximates the viewing conditions of in vivo surgery. To assess the quality of the models, a synthetic view of the operating field was produced by overlaying a color image on the reconstructed 3D model, and an image rendered from the 3D model was compared with a 2D image captured from the same view. Experiments conducted with an object of known geometry demonstrate that the system produces 3D models accurate to within 1.5 mm. The ability to produce accurate real-time 3D models of the operating field is a significant advancement toward augmented reality in minimally invasive surgery. An imaging system with this capability will potentially transform surgery by helping novice and expert surgeons alike to delineate variance in internal anatomy accurately.

Modeling the spatial distribution of forest crown biomass and effects on fire behavior with FUEL3D and WFDS

Treesearch

Russell A. Parsons; William Mell; Peter McCauley

2010-01-01

Crown fire poses challenges to fire managers and can endanger fire fighters. Understanding of how fire interacts with tree crowns is essential to informed decisions about crown fire. Current operational crown fire predictions in the United States assume homogeneous crown fuels. While a new class of research fire models, which model fire behavior with computational...

Thermal-hydraulics modeling for prototype testing of the W7-X high heat flux scraper element

DOE PAGES

Clark, Emily; Lumsdaine, Arnold; Boscary, Jean; ...

2017-07-28

The long-pulse operation of the Wendelstein 7-X (W7-X) stellarator experiment is scheduled to begin in 2020. This operational phase will be equipped with water-cooled plasma facing components to allow for longer pulse durations. Certain simulated plasma scenarios have been shown to produce heat fluxes that surpass the technological limits on the edges of the divertor target elements during steady-state operation. In order to reduce the heat load on the target elements, the addition of a “scraper element” (SE) is under investigation. The SE is composed of 24 water-cooled carbon fiber reinforced carbon composite monoblock units. Multiple full-scale prototypes have beenmore » tested in the GLADIS high heat flux test facility. Previous computational studies revealed discrepancies between the simulations and experimental measurements. In this work, single-phase thermal-hydraulics modeling was performed in ANSYS CFX to identify potential causes for such discrepancies. Possible explanations investigated were the effects of a non-uniform thermal contact resistance and a potential misalignment of the monoblock fibers. And while the difference between the experimental and computational results was not resolved by a non-uniform thermal contact resistance, the computational results provided insight into the potential performance of a W7-X monoblock unit. Circumferential temperature distributions highlighted the expected boiling regions of such a unit. Finally, simulations revealed that modest angles of fiber misalignment in the monoblocks result in asymmetries at the unit edges and provide temperature differences similar to the experimental results.« less

Thermal-hydraulics modeling for prototype testing of the W7-X high heat flux scraper element

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, Emily; Lumsdaine, Arnold; Boscary, Jean

The long-pulse operation of the Wendelstein 7-X (W7-X) stellarator experiment is scheduled to begin in 2020. This operational phase will be equipped with water-cooled plasma facing components to allow for longer pulse durations. Certain simulated plasma scenarios have been shown to produce heat fluxes that surpass the technological limits on the edges of the divertor target elements during steady-state operation. In order to reduce the heat load on the target elements, the addition of a “scraper element” (SE) is under investigation. The SE is composed of 24 water-cooled carbon fiber reinforced carbon composite monoblock units. Multiple full-scale prototypes have beenmore » tested in the GLADIS high heat flux test facility. Previous computational studies revealed discrepancies between the simulations and experimental measurements. In this work, single-phase thermal-hydraulics modeling was performed in ANSYS CFX to identify potential causes for such discrepancies. Possible explanations investigated were the effects of a non-uniform thermal contact resistance and a potential misalignment of the monoblock fibers. And while the difference between the experimental and computational results was not resolved by a non-uniform thermal contact resistance, the computational results provided insight into the potential performance of a W7-X monoblock unit. Circumferential temperature distributions highlighted the expected boiling regions of such a unit. Finally, simulations revealed that modest angles of fiber misalignment in the monoblocks result in asymmetries at the unit edges and provide temperature differences similar to the experimental results.« less

Interprofessional rhetoric and operational realities: an ethnographic study of rounds in four intensive care units.

PubMed

Paradis, Elise; Leslie, Myles; Gropper, Michael A

2016-10-01

Morning interprofessional rounds (MIRs) are used in critical care medicine to improve team-based care and patient outcomes. Given existing evidence of conflict between and dissatisfaction among rounds participants, this study sought to better understand how the operational realities of care delivery in the intensive care unit (ICU) impact the success of MIRs. We conducted a year-long comparative ethnographic study of interprofessional collaboration and patient and family involvement in four ICUs in tertiary academic hospitals in two American cities. The study included 576 h of observation of team interactions, 47 shadowing sessions and 40 clinician interviews. In line with best practices in ethnographic research, data collection and analysis were done iteratively using the constant comparative method. Member check was conducted regularly throughout the project. MIRs were implemented on all units with the explicit goals of improving team-based and patient-centered care. Operational conditions on the units, despite interprofessional commitment and engagement, appeared to thwart ICU teams from achieving these goals. Specifically, time constraints, struggles over space, and conflicts between MIRs' educational and care-plan-development functions all prevented teams from achieving collaboration and patient-involvement. Moreover, physicians' de facto control of rounds often meant that they resembled medical rounds (their historical predecessors), and sidelined other providers' contributions. This study suggests that the MIRs model, as presently practiced, might not be well suited to the provision of team-based, patient-centered care. In the interest of interprofessional collaboration, of the optimization of clinicians' time, of high-quality medical education and of patient-centered care, further research on interprofessional rounds models is needed.

Design and study of water supply system for supercritical unit boiler in thermal power station

NASA Astrophysics Data System (ADS)

Du, Zenghui

2018-04-01

In order to design and optimize the boiler feed water system of supercritical unit, the establishment of a highly accurate controlled object model and its dynamic characteristics are prerequisites for developing a perfect thermal control system. In this paper, the method of mechanism modeling often leads to large systematic errors. Aiming at the information contained in the historical operation data of the boiler typical thermal system, the modern intelligent identification method to establish a high-precision quantitative model is used. This method avoids the difficulties caused by the disturbance experiment modeling for the actual system in the field, and provides a strong reference for the design and optimization of the thermal automation control system in the thermal power plant.

Operational data and thermodynamic modeling of a Stirling-dish demonstration installation in desert conditions

NASA Astrophysics Data System (ADS)

Nilsson, Martin; Jamot, Jakob; Malm, Tommy

2017-06-01

To field test its Stirling-dish unit, Cleanergy AB of Sweden in Q1 2015 built a ten unit demo park in Dubai. The first STE (Solar Thermal Energy) generation of its Stirling genset, the C11S, had at its core an 11 kWel Stirling engine/generator combination. The genset was mated with a parabolic concentrator developed for the genset by a supplier. Local weather conditions in Dubai provide opportunities to test performance in an environment with high insolation and high ambient temperature. In addition, the conditions in Dubai are windy, salty, humid and dusty, historically challenging for solar technologies [1]. In Q1 2016 one of the C11S Stirling-dish units was replaced by the first prototype of Cleanergy's second generation Stirling genset, the Sunbox, and an in-house developed parabolic concentrator. Operational data from field testing during the spring of 2016 are presented and discussed and show the large performance improvement achieved with the Sunbox unit.

VAR and generalized impulse response analysis of manufacturing unit labor costs

NASA Astrophysics Data System (ADS)

Ewing, Bradley T.; Thompson, Mark A.

2008-04-01

This paper examines the relationship among manufacturing unit labor costs in the United States, United Kingdom, and Canada. The analysis is conducted within the context of an economic system utilizing the recently developed method of generalized impulse response analysis to simulate the responses of the cost series to disturbances. The results indicate that, while unit labor costs do not share a common stochastic trend, there are significant responses in the unit labor costs of each country to shocks in the costs of other countries that are not captured by standard interpretation of the multiple-equation model results. The findings indicate the presence of significant linkages among unit labor costs in the countries studied. The results are consistent with the economic environment of manufacturing operations being characterized by a competitive, integrated marketplace.

A New Generation of Electrical Power Supply for Telecom Satellites

NASA Astrophysics Data System (ADS)

Bouhours, Gilles; Asplanato, Remi; Rebuffel, Christophe; Pasquet, Jean-Marie; Bardin, Bertrand; Deplus, Nicolas; Lempereur, Vincent

2014-08-01

This paper presents the main features of the new power subsystem generation for the Thales Alenia Space (TAS) Spacebus platforms.All its components (Solar Array, Solar Array Drive Mechanism, Power Conditioning Unit and Lithium-Ion batteries) have been upgraded, taking advantage of the latest available technologies. The modularity has been improved to perfectly match the sizing of each unit to the satellite power level requirement. These two improvements lead to optimal mass and cost over the whole power range.In addition, the customer benefits from a fully automatic operation of the subsystem, including redundancy, making the ground station workload negligible, even during eclipse periods. Finally, the capability to support any type of payload has been further improved, in terms of overall power level and operating modes. Payload pulsed operation capability has been especially increased to support all anticipated mission requirements. In parallel to the PCU hardware, a detailed electrical model has also been developed and correlated to analyse the regulation performance in any nominal or degraded mode. An extensive set of tests provides a verification of performances and interfaces, hardware as well as software.This paper will first describe the main requirements considered in this development. Then, the architecture will be detailed, showing how the requirements have been fulfilled. The design of each unit will be shortly presented, and finally the correlation between the regulation analysis model and the EQM measurements will be illustrated.

Study on dynamic characteristics of hydraulic pumping unit on offshore platform

NASA Astrophysics Data System (ADS)

Chang, Zong-yu; Yu, Yan-qun; Qi, Yao-guang

2017-12-01

A new technology of offshore oil rod pumping production is developed for offshore heavy oil recovery. A new type of miniature hydraulic pumping unit with long-stroke, low pumping speed and compact structure is designed based on the spatial characteristics of offshore platforms. By combining the strengths of sinusoidal velocity curve and trapezoidal velocity curve, a kinematical model of the acceleration, the velocity and displacement of the pumping unit's hanging point is established. The results show that the pumping unit has good kinematic characteristics of smooth motion and small dynamic load. The multi-degree-of-freedom dynamic model of the single-well pumping unit is established. The first and second order natural frequencies of the sucker rod string subsystem and the pumping unit subsystem are studied. The results show that the first and the second order natural frequencies among the pumping rod string, pumping unit-platform subsystem and the dynamic excitation have differences over 5 times from each other, indicating that resonance phenomenon will not appear during the operation and the dynamic requirements for field use are met in the system.

NIC atomic operation unit with caching and bandwidth mitigation

DOEpatents

Hemmert, Karl Scott; Underwood, Keith D.; Levenhagen, Michael J.

2016-03-01

A network interface controller atomic operation unit and a network interface control method comprising, in an atomic operation unit of a network interface controller, using a write-through cache and employing a rate-limiting functional unit.

DAILY SIMULATIONS OF OZONE AND FINE PARTICULATES OVER THE NORTHEASTERN UNITED STATES: MODEL PERFORMANCE, SEASONAL DIFFERENCES, AND THE EFFECT OF MODEL UPDATES

EPA Science Inventory

This poster presents analysis of near-realtime air quality simulations over New York State for two summer and one winter season. Simulations were performed as a pilot study between the NOAA, EPA, and NYSDEC, utilizing resources from the national operational NOAA/EPA air quality f...

Operations Research techniques in the management of large-scale reforestation programs

Treesearch

Joseph Buongiorno; D.E. Teeguarden

1978-01-01

A reforestation planning system for the Douglas-fir region of the Western United States is described. Part of the system is a simulation model to predict plantation growth and to determine economic thinning regimes and rotation ages as a function of site characteristics, initial density, reforestation costs, and management constraints. A second model estimates the...

A Model for Institutional Policy Analysis: The Case of Student Financial Aid. AIR Forum 1981 Paper.

ERIC Educational Resources Information Center

Fenske, Robert H.; Parker, John D.

The development of an operational model that would enable a college institutional research unit to improve administrative decision-making by expanding its data base to include new activities not widely recognized throughout the institution is considered. Attention is directed to institutional research as a function within an institution,…

Work-Family Enrichment and Conflict: Additive Effects, Buffering, or Balance?

ERIC Educational Resources Information Center

Gareis, Karen C.; Barnett, Rosalind Chait; Ertel, Karen A.; Berkman, Lisa F.

2009-01-01

We used data from the Midlife Development in the United States (MIDUS I) (N = 2,031) to compare three models of how work-family conflict and enrichment might operate to predict well-being (mental health, life satisfaction, affect balance, partner relationship quality). We found no support for a relative-difference model in which the…

Synthesis and identification of parameters of regenerative device for reversing link with increasing speed

NASA Astrophysics Data System (ADS)

Dubinin, N. N.; Mikhailichenko, S. A.; Goncharov, S. I.

2018-03-01

The article shows the problem of modeling the flow of fibrous suspension in the working bodies of mixing machines. A mathematical model describing the motion of a suspension with fibrous inclusions in a wet-type disintegrator, depending on the design of the accelerating unit and the operating device is obtained.

Changes in Personality Disorder Traits Following 2 Years of Treatment in a Secure Therapeutic Community Milieu

ERIC Educational Resources Information Center

Morrissey, Catrin; Taylor, Jon

2014-01-01

Therapeutic community treatment models have not previously been applied to forensic patients with mild intellectual disabilities (IDs) with a comorbid diagnosis of personality disorder. Thirteen patients with mild IDs were allocated to a unit within a high secure psychiatric service operating a model of treatment based on the principles and…

Briefing paper : toward a best practice model for managed lanes in Texas.

DOT National Transportation Integrated Search

2013-09-01

Over the past two decades, agencies : have increasingly implemented managed : lanes (MLs) to mitigate growing urban traffic : congestion in the United States. Multiple operating : projects : representing a combination : of HOV-to-HOT conversions a...

40 CFR 60.1880 - When must I submit the annual report?

Code of Federal Regulations, 2010 CFR

2010-07-01

... of each year that follows the calendar year in which you collected the data. If you have an operating... Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule...

Extending aircraft performance modeling capabilities in the Aviation Environmental Design Tool (AEDT)

DOT National Transportation Integrated Search

2011-01-01

To support improved analysis of the environmental impacts of proposed global aircraft operational changes, the United States Federal Aviation Administration recently worked : with European academic partners to update the airport terminal area fuel co...

Study on Operation Optimization of Pumping Station's 24 Hours Operation under Influences of Tides and Peak-Valley Electricity Prices

NASA Astrophysics Data System (ADS)

Yi, Gong; Jilin, Cheng; Lihua, Zhang; Rentian, Zhang

2010-06-01

According to different processes of tides and peak-valley electricity prices, this paper determines the optimal start up time in pumping station's 24 hours operation between the rating state and adjusting blade angle state respectively based on the optimization objective function and optimization model for single-unit pump's 24 hours operation taking JiangDu No.4 Pumping Station for example. In the meantime, this paper proposes the following regularities between optimal start up time of pumping station and the process of tides and peak-valley electricity prices each day within a month: (1) In the rating and adjusting blade angle state, the optimal start up time in pumping station's 24 hours operation which depends on the tide generation at the same day varies with the process of tides. There are mainly two kinds of optimal start up time which include the time at tide generation and 12 hours after it. (2) In the rating state, the optimal start up time on each day in a month exhibits a rule of symmetry from 29 to 28 of next month in the lunar calendar. The time of tide generation usually exists in the period of peak electricity price or the valley one. The higher electricity price corresponds to the higher minimum cost of water pumping at unit, which means that the minimum cost of water pumping at unit depends on the peak-valley electricity price at the time of tide generation on the same day. (3) In the adjusting blade angle state, the minimum cost of water pumping at unit in pumping station's 24 hour operation depends on the process of peak-valley electricity prices. And in the adjusting blade angle state, 4.85%˜5.37% of the minimum cost of water pumping at unit will be saved than that of in the rating state.

Biophysically based mathematical modeling of interstitial cells of Cajal slow wave activity generated from a discrete unitary potential basis.

PubMed

Faville, R A; Pullan, A J; Sanders, K M; Koh, S D; Lloyd, C M; Smith, N P

2009-06-17

Spontaneously rhythmic pacemaker activity produced by interstitial cells of Cajal (ICC) is the result of the entrainment of unitary potential depolarizations generated at intracellular sites termed pacemaker units. In this study, we present a mathematical modeling framework that quantitatively represents the transmembrane ion flows and intracellular Ca2+ dynamics from a single ICC operating over the physiological membrane potential range. The mathematical model presented here extends our recently developed biophysically based pacemaker unit modeling framework by including mechanisms necessary for coordinating unitary potential events, such as a T-Type Ca2+ current, Vm-dependent K+ currents, and global Ca2+ diffusion. Model simulations produce spontaneously rhythmic slow wave depolarizations with an amplitude of 65 mV at a frequency of 17.4 cpm. Our model predicts that activity at the spatial scale of the pacemaker unit is fundamental for ICC slow wave generation, and Ca2+ influx from activation of the T-Type Ca2+ current is required for unitary potential entrainment. These results suggest that intracellular Ca2+ levels, particularly in the region local to the mitochondria and endoplasmic reticulum, significantly influence pacing frequency and synchronization of pacemaker unit discharge. Moreover, numerical investigations show that our ICC model is capable of qualitatively replicating a wide range of experimental observations.

Spatiotemporal variability of snow depletion curves derived from SNODAS for the conterminous United States, 2004-2013

USGS Publications Warehouse

Driscoll, Jessica; Hay, Lauren E.; Bock, Andrew R.

2017-01-01

Assessment of water resources at a national scale is critical for understanding their vulnerability to future change in policy and climate. Representation of the spatiotemporal variability in snowmelt processes in continental-scale hydrologic models is critical for assessment of water resource response to continued climate change. Continental-extent hydrologic models such as the U.S. Geological Survey National Hydrologic Model (NHM) represent snowmelt processes through the application of snow depletion curves (SDCs). SDCs relate normalized snow water equivalent (SWE) to normalized snow covered area (SCA) over a snowmelt season for a given modeling unit. SDCs were derived using output from the operational Snow Data Assimilation System (SNODAS) snow model as daily 1-km gridded SWE over the conterminous United States. Daily SNODAS output were aggregated to a predefined watershed-scale geospatial fabric and used to also calculate SCA from October 1, 2004 to September 30, 2013. The spatiotemporal variability in SNODAS output at the watershed scale was evaluated through the spatial distribution of the median and standard deviation for the time period. Representative SDCs for each watershed-scale modeling unit over the conterminous United States (n = 54,104) were selected using a consistent methodology and used to create categories of snowmelt based on SDC shape. The relation of SDC categories to the topographic and climatic variables allow for national-scale categorization of snowmelt processes.

High-fidelity, simulation-based, interdisciplinary operating room team training at the point of care.

PubMed

Paige, John T; Kozmenko, Valeriy; Yang, Tong; Paragi Gururaja, Ramnarayan; Hilton, Charles W; Cohn, Isidore; Chauvin, Sheila W

2009-02-01

The operating room (OR) is a dynamic, high risk setting requiring effective teamwork for the safe delivery of care. Teamwork in the modern OR, however, is less than ideal. High fidelity simulation is an attractive approach to training key teamwork competencies. We have developed a portable simulation platform, the mobile mock OR (MMOR) that permits bringing team training over long distances to the point of care. We examined the effectiveness of this innovative, simulation-based interdisciplinary operating room (OR) team training model on its participants. All general surgical OR team members at an academic affiliated medical center underwent scenario-based training using a mobile mock OR. Pre- and post-session mean scores were calculated and analyzed for 15 Likert-type items measuring self-efficacy in teamwork competencies using t test. The mean gain in pre-post item scores for 38 participants averaged 0.4 units on a 6-point Likert scale. The significance was demonstrated in 4 of the items: role clarity (Delta = 0.6 units, P = .02), anticipatory response (Delta = 0.6 units, P = .01), cross monitoring (Delta = 0.6 units, P < .01), and team cohesion and interaction (Delta = 0.7 units, P < .01). High-fidelity, simulation-based OR team training at the point of care positively impacts self-efficacy for effective teamwork performance in everyday practice.

Very large scale monoclonal antibody purification: the case for conventional unit operations.

PubMed

Kelley, Brian

2007-01-01

Technology development initiatives targeted for monoclonal antibody purification may be motivated by manufacturing limitations and are often aimed at solving current and future process bottlenecks. A subject under debate in many biotechnology companies is whether conventional unit operations such as chromatography will eventually become limiting for the production of recombinant protein therapeutics. An evaluation of the potential limitations of process chromatography and filtration using today's commercially available resins and membranes was conducted for a conceptual process scaled to produce 10 tons of monoclonal antibody per year from a single manufacturing plant, a scale representing one of the world's largest single-plant capacities for cGMP protein production. The process employs a simple, efficient purification train using only two chromatographic and two ultrafiltration steps, modeled after a platform antibody purification train that has generated 10 kg batches in clinical production. Based on analyses of cost of goods and the production capacity of this very large scale purification process, it is unlikely that non-conventional downstream unit operations would be needed to replace conventional chromatographic and filtration separation steps, at least for recombinant antibodies.

40 CFR 60.2635 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines... CISWI unit can be operated unless a fully trained and qualified CISWI unit operator is accessible... operator may operate the CISWI unit directly or be the direct supervisor of one or more other plant...

40 CFR 60.2635 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines... CISWI unit can be operated unless a fully trained and qualified CISWI unit operator is accessible... operator may operate the CISWI unit directly or be the direct supervisor of one or more other plant...

Mountain-Plains Handbook: The Design and Operation of a Residential Family Based Education Program. Appendix. Supplement Four to Volume Three. Measurement and Evaluation: The Research Services Division.

ERIC Educational Resources Information Center

Coyle, David A.; And Others

One of five supplements which accompany chapter 3 of "Mountain-Plains Handbook: The Design and Operation of a Residential, Family Oriented Career Education Model" (CE 014 630), this document contains a master listing of all Mountain-Plains curriculum, compiled by job title, course, unit, and Learning activity package (LAPS) and arranged…

Dedicated education unit: implementing an innovation in replication sites.

PubMed

Moscato, Susan R; Nishioka, Vicki M; Coe, Michael T

2013-05-01

An important measure of an innovation is the ease of replication and achievement of the same positive outcomes. The dedicated education unit (DEU) clinical education model uses a collaborative academic-service partnership to develop an optimal learning environment for students. The University of Portland adapted this model from Flinders University, Australia, to increase the teaching capacity and quality of nursing education. This article identifies DEU implementation essentials and reports on the outcomes of two replication sites that received consultation support from the University of Portland. Program operation information, including education requirements for clinician instructors, types of patient care units, and clinical faculty-to-student ratios is presented. Case studies of the three programs suggest the DEU model is adaptable to a range of different clinical settings and continues to show promise as one strategy for addressing the nurse faculty shortage and strengthening academic-clinical collaborations while maintaining quality clinical education for students. Copyright 2013, SLACK Incorporated.

Fault tolerant system with imperfect coverage, reboot and server vacation

NASA Astrophysics Data System (ADS)

Jain, Madhu; Meena, Rakesh Kumar

2017-06-01

This study is concerned with the performance modeling of a fault tolerant system consisting of operating units supported by a combination of warm and cold spares. The on-line as well as warm standby units are subject to failures and are send for the repair to a repair facility having single repairman which is prone to failure. If the failed unit is not detected, the system enters into an unsafe state from which it is cleared by the reboot and recovery action. The server is allowed to go for vacation if there is no failed unit present in the system. Markov model is developed to obtain the transient probabilities associated with the system states. Runge-Kutta method is used to evaluate the system state probabilities and queueing measures. To explore the sensitivity and cost associated with the system, numerical simulation is conducted.

Using Simulation to Model Improvements in Pediatric Bed Placement in an Acute Care Hospital.

PubMed

Lambton, Judith; Roeder, Theresa; Saltzman, Robert; Param, Lila; Fernandes, Roxanne

2017-02-01

The objective of this project was to use an interdisciplinary approach to analyze strategies through simulation technology for improving patient flow in a pediatric hospital. Various statistics have been offered on the number of children admitted annually to hospitals. For administrators, particularly in smaller systems, the financial burden of equipping and staffing pediatric units often outweighs the moral desire to maintain a pediatric unit as a viable option for patients and pediatricians. Discrete event simulation was used to model current operations of a pediatric unit. Cost analysis was conducted using simulation reflecting various percentages of patients being referred to a discharge holding area (DHA) upon discharge and of the use of all private rooms. Both DHA and private rooms resulted in increased patient volumes. Administrators should consider the use of a DHA and/or private rooms to ease the census strains of pediatric units and the resultant revenue of this service.

Evaluation of the Township Proper Carrying Capacity over Qinghai-Tibet plateau by CASA model

NASA Astrophysics Data System (ADS)

Wu, Chengyong; Cao, Guangchao; Xue, Huaju; Jiang, Gang; Wang, Qi; Yuan, Jie; Chen, Kelong

2018-01-01

The existing study of proper carrying capacity (PCC) has mostly focused on province or county administrative units, which can only macroscopically master the quantitative characteristics of PCC, but could not effectively take some animal husbandry management measures that are pertinent and operational. At town-scale, this paper used CASA model to estimate the PCC in Mongolian Autonomous County of Henan, Qinghai province, China,with serious grassland degeneration that mainly caused by overgrazing. The results showed that the PCC throughout the County was 950,417 sheep unit. For the township, the PCC of Saierlong and Duosong were the largest (247,100 sheep unit) and the smallest (82,016 sheep unit) respectively. This study will provide reference data for developing sustainable development of town-scale pasture policies and also will help to evaluate the health status of the alpine grassland ecosystem on Qinghai-Tibet plateau.

An experimental study of dependence of hydro turbine vibration parameters on pressure pulsations in the flow path

NASA Astrophysics Data System (ADS)

Dekterev, D.; Maslennikova, A.; Abramov, A.

2017-09-01

The operation modes of the hydraulic power plant water turbine with the formation of a precessing vortex core were studied on the hydrodynamic set-up with the model of hydraulic unit. The dependence of low-frequency vibrations on flow pressure pulsations in the hydraulic unit was established. The results of the air injection effect on the vibrational parameters of the hydrodynamic set-up were presented.

The Operational Mentoring and Liaison Team Program as a Model for Assisting the Development of an Effective Afghan National Army

DTIC Science & Technology

2009-06-12

care has been taken to ensure the ANA is comprised of soldiers from all of Afghanistan’s major ethnic groups - Pashtun, Tajik, Uzbek , Hazara, Turkmen...Canada, Croatia, France, Germany, Italy, Netherlands, Poland , Spain, the United Kingdom (UK), and United States have contributed full OMLTs/ETTs...embedded training teams) while Canada, Croatia, Czech Republic, France, Germany, Latvia, Netherlands, Norway, Poland , Portugal, Romania, Slovenia

Air-Land Battle Interdiction Model Corps Communications Module.

DTIC Science & Technology

1984-06-01

raniel R. Alexander Capain,United States Army B.S.gUnitQ States Military Acade y,1975 Submitted in partial fulfillment of the requirements for the...Chairman, Department of Operations Research Lea ofInformation aLean o ic Sciences 4 3 I. ’k - Pi -,-.’ * I ABSTRACT This thesis provides the detailed...communications is in the midst of a revolu- tionary change from tubes to microchip technology , and an equally revclutionary doctrinal change. The

Capability-Based Modeling Methodology: A Fleet-First Approach to Architecture

DTIC Science & Technology

2014-02-01

reconnaissance (ISR) aircraft , or unmanned systems . Accordingly, a mission architecture used to model SAG operations for a given Fleet unit should include all...would use an ISR aircraft to increase fidelity of a targeting solution; another mission thread to show how unmanned systems can augment targeting... unmanned systems . Therefore, an architect can generate, from a comprehensive SAG mission architecture, individual mission threads that model how a SAG

Model-Based Sensor Placement for Component Condition Monitoring and Fault Diagnosis in Fossil Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mobed, Parham; Pednekar, Pratik; Bhattacharyya, Debangsu

Design and operation of energy producing, near “zero-emission” coal plants has become a national imperative. This report on model-based sensor placement describes a transformative two-tier approach to identify the optimum placement, number, and type of sensors for condition monitoring and fault diagnosis in fossil energy system operations. The algorithms are tested on a high fidelity model of the integrated gasification combined cycle (IGCC) plant. For a condition monitoring network, whether equipment should be considered at a unit level or a systems level depends upon the criticality of the process equipment, its likeliness to fail, and the level of resolution desiredmore » for any specific failure. Because of the presence of a high fidelity model at the unit level, a sensor network can be designed to monitor the spatial profile of the states and estimate fault severity levels. In an IGCC plant, besides the gasifier, the sour water gas shift (WGS) reactor plays an important role. In view of this, condition monitoring of the sour WGS reactor is considered at the unit level, while a detailed plant-wide model of gasification island, including sour WGS reactor and the Selexol process, is considered for fault diagnosis at the system-level. Finally, the developed algorithms unify the two levels and identifies an optimal sensor network that maximizes the effectiveness of the overall system-level fault diagnosis and component-level condition monitoring. This work could have a major impact on the design and operation of future fossil energy plants, particularly at the grassroots level where the sensor network is yet to be identified. In addition, the same algorithms developed in this report can be further enhanced to be used in retrofits, where the objectives could be upgrade (addition of more sensors) and relocation of existing sensors.« less

Inventory model with two rates of production for deteriorating items with permissible delay in payments

NASA Astrophysics Data System (ADS)

Roy, Ajanta; Samanta, G. P.

2011-08-01

Goyal (1985) ['Economic Order Quantity Under Conditions of Permissible Delay in Payments', Journal of Operational research Society, 36, 35-38] assumed that unit selling price and unit purchasing price are equal. But in real-life the scenario is different. The purpose of this article is to reflect the real life problem by allowing unit selling price and purchasing price to be unequal. Our model is a continuous production control inventory model for deteriorating items in which two different rates of production are available. The results are illustrated with the help of a numerical example. We discuss the sensitivity of the solution together with the changes of the values of the parameters associated with the model. Our model may be applicable in many manufacturing planning situations where management practices for deterioration are stringent; e.g. the two-production rate will be more profitable than the one-production rate in the manufacture of cold, asthma and allergy medicine. Our proposed model might be applicable to develop a prototype advance planning system for those manufacturers to integrate the management science techniques into commercial planning.

A mathematical model for the iron/chromium redox battery

NASA Technical Reports Server (NTRS)

Fedkiw, P. S.; Watts, R. W.

1984-01-01

A mathematical model has been developed to describe the isothermal operation of a single anode-separator-cathode unit cell in a redox-flow battery and has been applied to the NASA iron/chromium system. The model, based on porous electrode theory, incorporates redox kinetics, mass transfer, and ohmic effects as well as the parasitic hydrogen reaction which occurs in the chromium electrode. A numerical parameter study was carried out to predict cell performance to aid in the rational design, scale-up, and operation of the flow battery. The calculations demonstrate: (1) an optimum electrode thickness and electrolyte flow rate exist; (2) the amount of hydrogen evolved and, hence, cycle faradaic efficiency, can be affected by cell geometry, flow rate, and charging procedure; (3) countercurrent flow results in enhanced cell performance over cocurrent flow; and (4) elevated temperature operation enhances cell performance.

Apparatus for sensor failure detection and correction in a gas turbine engine control system

NASA Technical Reports Server (NTRS)

Spang, H. A., III; Wanger, R. P. (Inventor)

1981-01-01

A gas turbine engine control system maintains a selected level of engine performance despite the failure or abnormal operation of one or more engine parameter sensors. The control system employs a continuously updated engine model which simulates engine performance and generates signals representing real time estimates of the engine parameter sensor signals. The estimate signals are transmitted to a control computational unit which utilizes them in lieu of the actual engine parameter sensor signals to control the operation of the engine. The estimate signals are also compared with the corresponding actual engine parameter sensor signals and the resulting difference signals are utilized to update the engine model. If a particular difference signal exceeds specific tolerance limits, the difference signal is inhibited from updating the model and a sensor failure indication is provided to the engine operator.

40 CFR Table 8 to Subpart Bbbb of... - Model Rule-Requirements for Stack Tests

Code of Federal Regulations, 2010 CFR

2010-07-01

... at full load. 2. Metals Cadmium Method 1 Method 29 a Compliance testing must be performed while the... be performed while the municipal waste combustion unit is operating at full load. Mercury Method 1...

Developing an Information Resources Management Curriculum.

ERIC Educational Resources Information Center

Montie, Irene C.

1983-01-01

Discusses the development of an Information Resources Management (IRM) curriculum by the IRM Curriculum Advisory Committee established by the Graduate School, United States Department of Agriculture. Initial activities, models proposed for the program (standards, skills, users, operational), course selection, and structural proposals considered…

Modeling the Control Systems of Gas-Turbines to Ensure Their Reliable Parallel Operation in the UPS of Russia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vinogradov, A. Yu., E-mail: vinogradov-a@ntcees.ru; Gerasimov, A. S.; Kozlov, A. V.

Consideration is given to different approaches to modeling the control systems of gas turbines as a component of CCPP and GTPP to ensure their reliable parallel operation in the UPS of Russia. The disadvantages of the approaches to the modeling of combined-cycle units in studying long-term electromechanical transients accompanied by power imbalance are pointed out. Examples are presented to support the use of more detailed models of gas turbines in electromechanical transient calculations. It is shown that the modern speed control systems of gas turbines in combination with relatively low equivalent inertia have a considerable effect on electromechanical transients, includingmore » those caused by disturbances not related to power imbalance.« less

Development and validation of the new ICNARC model for prediction of acute hospital mortality in adult critical care.

PubMed

Ferrando-Vivas, Paloma; Jones, Andrew; Rowan, Kathryn M; Harrison, David A

2017-04-01

To develop and validate an improved risk model to predict acute hospital mortality for admissions to adult critical care units in the UK. 155,239 admissions to 232 adult critical care units in England, Wales and Northern Ireland between January and December 2012 were used to develop a risk model from a set of 38 candidate predictors. The model was validated using 90,017 admissions between January and September 2013. The final model incorporated 15 physiological predictors (modelled with continuous nonlinear models), age, dependency prior to hospital admission, chronic liver disease, metastatic disease, haematological malignancy, CPR prior to admission, location prior to admission/urgency of admission, primary reason for admission and interaction terms. The model was well calibrated and outperformed the current ICNARC model on measures of discrimination (area under the receiver operating characteristic curve 0.885 versus 0.869) and model fit (Brier's score 0.108 versus 0.115). On average, the new model reclassified patients into more appropriate risk categories (net reclassification improvement 19.9; P<0.0001). The model performed well across patient subgroups and in specialist critical care units. The risk model developed in this study showed excellent discrimination and calibration and when validated on a different period of time and across different types of critical care unit. This in turn allows improved accuracy of comparisons between UK critical care providers. Copyright © 2016. Published by Elsevier Inc.

Enhanced Teaching and Student Learning through a Simulator-Based Course in Chemical Unit Operations Design

ERIC Educational Resources Information Center

Ghasem, Nayef

2016-01-01

This paper illustrates a teaching technique used in computer applications in chemical engineering employed for designing various unit operation processes, where the students learn about unit operations by designing them. The aim of the course is not to teach design, but rather to teach the fundamentals and the function of unit operation processes…

Overview--Development of a geodatabase and conceptual model of the hydrogeologic units beneath Air Force Plant 4 and Naval Air Station-Joint Reserve Base Carswell Field, Fort Worth, Texas

USGS Publications Warehouse

Shah, Sachin D.

2004-01-01

Air Force Plant 4 (AFP4) and adjacent Naval Air Station-Joint Reserve Base Carswell Field (NAS–JRB) at Fort Worth, Tex., constitute a contractor-owned, government-operated facility that has been in operation since 1942. Contaminants from the 3,600-acre facility, primarily volatile organic compounds (VOCs) and metals, have entered the ground-water-flow system through leakage from waste-disposal sites and from manufacturing processes. Environmental data collected at AFP4 and NAS–JRB during 1993–2002 created the need for consolidation of the data into a comprehensive temporal and spatial geodatabase. The U.S. Geological Survey (USGS), in cooperation with the U.S. Air Force Aeronautical Systems Center Environmental Management Directorate, developed a comprehensive geodatabase of temporal and spatial environmental data associated with the hydrogeologic units beneath the facility. A three-dimensional conceptual model of the hydrogeologic units integrally linked to the geodatabase was designed concurrently. Three hydrogeologic units—from land surface downward, the alluvial aquifer, the GoodlandWalnut confining unit, and the Paluxy aquifer—compose the subsurface of interest at AFP4 and NAS–JRB. The alluvial aquifer consists primarily of clay and silt with sand and gravel channel deposits that might be interconnected or interfingered. The Goodland-Walnut confining unit directly underlies the alluvial aquifer and consists of limestone, marl, shale, and clay. The Paluxy aquifer is composed of dense mudstone and fine- to coarse-grained sandstone

Development of a diagnosis- and procedure-based risk model for 30-day outcome after pediatric cardiac surgery.

PubMed

Crowe, Sonya; Brown, Kate L; Pagel, Christina; Muthialu, Nagarajan; Cunningham, David; Gibbs, John; Bull, Catherine; Franklin, Rodney; Utley, Martin; Tsang, Victor T

2013-05-01

The study objective was to develop a risk model incorporating diagnostic information to adjust for case-mix severity during routine monitoring of outcomes for pediatric cardiac surgery. Data from the Central Cardiac Audit Database for all pediatric cardiac surgery procedures performed in the United Kingdom between 2000 and 2010 were included: 70% for model development and 30% for validation. Units of analysis were 30-day episodes after the first surgical procedure. We used logistic regression for 30-day mortality. Risk factors considered included procedural information based on Central Cardiac Audit Database "specific procedures," diagnostic information defined by 24 "primary" cardiac diagnoses and "univentricular" status, and other patient characteristics. Of the 27,140 30-day episodes in the development set, 25,613 were survivals, 834 were deaths, and 693 were of unknown status (mortality, 3.2%). The risk model includes procedure, cardiac diagnosis, univentricular status, age band (neonate, infant, child), continuous age, continuous weight, presence of non-Down syndrome comorbidity, bypass, and year of operation 2007 or later (because of decreasing mortality). A risk score was calculated for 95% of cases in the validation set (weight missing in 5%). The model discriminated well; the C-index for validation set was 0.77 (0.81 for post-2007 data). Removal of all but procedural information gave a reduced C-index of 0.72. The model performed well across the spectrum of predicted risk, but there was evidence of underestimation of mortality risk in neonates undergoing operation from 2007. The risk model performs well. Diagnostic information added useful discriminatory power. A future application is risk adjustment during routine monitoring of outcomes in the United Kingdom to assist quality assurance. Copyright © 2013 The American Association for Thoracic Surgery. Published by Mosby, Inc. All rights reserved.

40 CFR 63.1402 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... properties may vary with time. For a unit operation operated in a batch mode (i.e., batch unit operation... means a unit operation operated in a batch mode. Block means the time period that comprises a single batch cycle. Combustion device burner means a device designed to mix and ignite fuel and air to provide...

40 CFR 63.1402 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... properties may vary with time. For a unit operation operated in a batch mode (i.e., batch unit operation... means a unit operation operated in a batch mode. Block means the time period that comprises a single batch cycle. Combustion device burner means a device designed to mix and ignite fuel and air to provide...

40 CFR 63.1402 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... properties may vary with time. For a unit operation operated in a batch mode (i.e., batch unit operation... means a unit operation operated in a batch mode. Block means the time period that comprises a single batch cycle. Combustion device burner means a device designed to mix and ignite fuel and air to provide...

40 CFR 63.1402 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... properties may vary with time. For a unit operation operated in a batch mode (i.e., batch unit operation... means a unit operation operated in a batch mode. Block means the time period that comprises a single batch cycle. Combustion device burner means a device designed to mix and ignite fuel and air to provide...

40 CFR 63.1402 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... properties may vary with time. For a unit operation operated in a batch mode (i.e., batch unit operation... means a unit operation operated in a batch mode. Block means the time period that comprises a single batch cycle. Combustion device burner means a device designed to mix and ignite fuel and air to provide...

40 CFR 60.2905 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Operator Training... unit can be operated unless a fully trained and qualified OSWI unit operator is accessible, either at... operate the OSWI unit directly or be the direct supervisor of one or more other plant personnel who...

40 CFR 62.14595 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... operate the CISWI unit directly or be the direct supervisor of one or more other plant personnel who operate the unit. If all qualified CISWI unit operators are temporarily not accessible, you must follow the procedures in § 62.14625. (b) Operator training and qualification must be obtained through a State...

40 CFR 62.14595 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... operate the CISWI unit directly or be the direct supervisor of one or more other plant personnel who operate the unit. If all qualified CISWI unit operators are temporarily not accessible, you must follow the procedures in § 62.14625. (b) Operator training and qualification must be obtained through a State...

40 CFR 60.2905 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Operator Training... unit can be operated unless a fully trained and qualified OSWI unit operator is accessible, either at... operate the OSWI unit directly or be the direct supervisor of one or more other plant personnel who...

40 CFR 60.4810 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... the operator training and qualification requirements? (a) A SSI unit cannot be operated unless a fully... within 1 hour. The trained and qualified SSI unit operator may operate the SSI unit directly or be the...

40 CFR 60.4810 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... the operator training and qualification requirements? (a) A SSI unit cannot be operated unless a fully... within 1 hour. The trained and qualified SSI unit operator may operate the SSI unit directly or be the...

40 CFR 60.4810 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... the operator training and qualification requirements? (a) A SSI unit cannot be operated unless a fully... within 1 hour. The trained and qualified SSI unit operator may operate the SSI unit directly or be the...

40 CFR 60.2905 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Operator Training... unit can be operated unless a fully trained and qualified OSWI unit operator is accessible, either at... operate the OSWI unit directly or be the direct supervisor of one or more other plant personnel who...

40 CFR 62.15135 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2014 CFR

2014-07-01

... certification, who may operate the municipal waste combustion unit? 62.15135 Section 62.15135 Protection of... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operator Certification... combustion unit? After the required date for full or provisional certification, you must not operate your...

40 CFR 62.15135 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2012 CFR

2012-07-01

... certification, who may operate the municipal waste combustion unit? 62.15135 Section 62.15135 Protection of... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operator Certification... combustion unit? After the required date for full or provisional certification, you must not operate your...

40 CFR 62.15135 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2013 CFR

2013-07-01

... certification, who may operate the municipal waste combustion unit? 62.15135 Section 62.15135 Protection of... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operator Certification... combustion unit? After the required date for full or provisional certification, you must not operate your...

40 CFR 62.15135 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2011 CFR

2011-07-01

... certification, who may operate the municipal waste combustion unit? 62.15135 Section 62.15135 Protection of... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operator Certification... combustion unit? After the required date for full or provisional certification, you must not operate your...

40 CFR 62.15135 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2010 CFR

2010-07-01

... certification, who may operate the municipal waste combustion unit? 62.15135 Section 62.15135 Protection of... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operator Certification... combustion unit? After the required date for full or provisional certification, you must not operate your...

Distributed Computing for Signal Processing: Modeling of Asynchronous Parallel Computation. Appendix G. On the Design and Modeling of Special Purpose Parallel Processing Systems.

DTIC Science & Technology

1985-05-01

unit in the data base, with knowing one generic assembly language. °-’--a 139 The 5-tuple describing single operation execution time of the operations...TSi-- generate , random eventi ( ,.0-15 tieit tmls - ((floa egus ()16 274 r Ispt imet imel I at :EVE’JS- II ktime=0.0; /0 present time 0/ rrs ptime=0.0...computing machinery capable of performing these tasks within a given time constraint. Because the majority of the available computing machinery is general

Study on safety operation for large hydroelectric generator unit

NASA Astrophysics Data System (ADS)

Yan, Z. G.; Cui, T.; Zhou, L. J.; Zhi, F. L.; Wang, Z. W.

2012-11-01

Hydroelectric generator unit is a complex mechanical system which is composed of hydraulic turbine and electric generator. Rotary system is supported by the bearing bracket and the reinforced concrete structures, and vibration problem can't be avoided in the process of operating. Many large-scale hydroelectric units have been damaged because of the vibration problem in recent years. As the increase of the hydraulic turbine unit capacity and water head, the safe operation of hydraulic turbine has become a focus research in many countries. The operating characteristics of the hydraulic turbine have obvious differences at different working conditions. Based on the combination of field measurement and theoretical calculation, this paper shows a deep research on the safe operation of a large-scale Francis turbine unit. Firstly, the measurements of vibration, swing, pressure fluctuation and noise were carried out at 4 different heads. And also the relationships between vibrations and pressure fluctuations at different heads and working conditions were analysed deeply. Then the scientific prediction of safe operation for the unit at high head were done based on the CFD numerical calculation. Finally, this paper shows the division of the operating zone for the hydroelectric unit. According to the experimental results (vibrations, swings, pressure fluctuations and noise) as well as the theoretical results, the operating zone of the unit has been divided into three sections: prohibited operating zone, transition operating zone and safe operating zone. After this research was applied in the hydropower station, the security and economic efficiency of unit increased greatly, and enormous economic benefits and social benefits have been obtained.

Environmental Engineering Unit Operations and Unit Processes Laboratory Manual.

ERIC Educational Resources Information Center

O'Connor, John T., Ed.

This manual was prepared for the purpose of stimulating the development of effective unit operations and unit processes laboratory courses in environmental engineering. Laboratory activities emphasizing physical operations, biological, and chemical processes are designed for various educational and equipment levels. An introductory section reviews…

Modeling and sliding mode predictive control of the ultra-supercritical boiler-turbine system with uncertainties and input constraints.

PubMed

Tian, Zhen; Yuan, Jingqi; Zhang, Xiang; Kong, Lei; Wang, Jingcheng

2018-05-01

The coordinated control system (CCS) serves as an important role in load regulation, efficiency optimization and pollutant reduction for coal-fired power plants. The CCS faces with tough challenges, such as the wide-range load variation, various uncertainties and constraints. This paper aims to improve the load tacking ability and robustness for boiler-turbine units under wide-range operation. To capture the key dynamics of the ultra-supercritical boiler-turbine system, a nonlinear control-oriented model is developed based on mechanism analysis and model reduction techniques, which is validated with the history operation data of a real 1000 MW unit. To simultaneously address the issues of uncertainties and input constraints, a discrete-time sliding mode predictive controller (SMPC) is designed with the dual-mode control law. Moreover, the input-to-state stability and robustness of the closed-loop system are proved. Simulation results are presented to illustrate the effectiveness of the proposed control scheme, which achieves good tracking performance, disturbance rejection ability and compatibility to input constraints. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Sensitivity study of Space Station Freedom operations cost and selected user resources

NASA Technical Reports Server (NTRS)

Accola, Anne; Fincannon, H. J.; Williams, Gregory J.; Meier, R. Timothy

1990-01-01

The results of sensitivity studies performed to estimate probable ranges for four key Space Station parameters using the Space Station Freedom's Model for Estimating Space Station Operations Cost (MESSOC) are discussed. The variables examined are grouped into five main categories: logistics, crew, design, space transportation system, and training. The modification of these variables implies programmatic decisions in areas such as orbital replacement unit (ORU) design, investment in repair capabilities, and crew operations policies. The model utilizes a wide range of algorithms and an extensive trial logistics data base to represent Space Station operations. The trial logistics data base consists largely of a collection of the ORUs that comprise the mature station, and their characteristics based on current engineering understanding of the Space Station. A nondimensional approach is used to examine the relative importance of variables on parameters.

MODEL BASED BIOMASS SYSTEM DESIGN OF FEEDSTOCK SUPPLY SYSTEMS FOR BIOENERGY PRODUCTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

David J. Muth, Jr.; Jacob J. Jacobson; Kenneth M. Bryden

Engineering feedstock supply systems that deliver affordable, high-quality biomass remains a challenge for the emerging bioenergy industry. Cellulosic biomass is geographically distributed and has diverse physical and chemical properties. Because of this feedstock supply systems that deliver cellulosic biomass resources to biorefineries require integration of a broad set of engineered unit operations. These unit operations include harvest and collection, storage, preprocessing, and transportation processes. Design decisions for each feedstock supply system unit operation impact the engineering design and performance of the other system elements. These interdependencies are further complicated by spatial and temporal variances such as climate conditions and biomassmore » characteristics. This paper develops an integrated model that couples a SQL-based data management engine and systems dynamics models to design and evaluate biomass feedstock supply systems. The integrated model, called the Biomass Logistics Model (BLM), includes a suite of databases that provide 1) engineering performance data for hundreds of equipment systems, 2) spatially explicit labor cost datasets, and 3) local tax and regulation data. The BLM analytic engine is built in the systems dynamics software package PowersimTM. The BLM is designed to work with thermochemical and biochemical based biofuel conversion platforms and accommodates a range of cellulosic biomass types (i.e., herbaceous residues, short- rotation woody and herbaceous energy crops, woody residues, algae, etc.). The BLM simulates the flow of biomass through the entire supply chain, tracking changes in feedstock characteristics (i.e., moisture content, dry matter, ash content, and dry bulk density) as influenced by the various operations in the supply chain. By accounting for all of the equipment that comes into contact with biomass from the point of harvest to the throat of the conversion facility and the change in characteristics, the BLM evaluates economic performance of the engineered system, as well as determining energy consumption and green house gas performance of the design. This paper presents a BLM case study delivering corn stover to produce cellulosic ethanol. The case study utilizes the BLM to model the performance of several feedstock supply system designs. The case study also explores the impact of temporal variations in climate conditions to test the sensitivity of the engineering designs. Results from the case study show that under certain conditions corn stover can be delivered to the cellulosic ethanol biorefinery for $35/dry ton.« less

Modeling of yield and environmental impact categories in tea processing units based on artificial neural networks.

PubMed

Khanali, Majid; Mobli, Hossein; Hosseinzadeh-Bandbafha, Homa

2017-12-01

In this study, an artificial neural network (ANN) model was developed for predicting the yield and life cycle environmental impacts based on energy inputs required in processing of black tea, green tea, and oolong tea in Guilan province of Iran. A life cycle assessment (LCA) approach was used to investigate the environmental impact categories of processed tea based on the cradle to gate approach, i.e., from production of input materials using raw materials to the gate of tea processing units, i.e., packaged tea. Thus, all the tea processing operations such as withering, rolling, fermentation, drying, and packaging were considered in the analysis. The initial data were obtained from tea processing units while the required data about the background system was extracted from the EcoInvent 2.2 database. LCA results indicated that diesel fuel and corrugated paper box used in drying and packaging operations, respectively, were the main hotspots. Black tea processing unit caused the highest pollution among the three processing units. Three feed-forward back-propagation ANN models based on Levenberg-Marquardt training algorithm with two hidden layers accompanied by sigmoid activation functions and a linear transfer function in output layer, were applied for three types of processed tea. The neural networks were developed based on energy equivalents of eight different input parameters (energy equivalents of fresh tea leaves, human labor, diesel fuel, electricity, adhesive, carton, corrugated paper box, and transportation) and 11 output parameters (yield, global warming, abiotic depletion, acidification, eutrophication, ozone layer depletion, human toxicity, freshwater aquatic ecotoxicity, marine aquatic ecotoxicity, terrestrial ecotoxicity, and photochemical oxidation). The results showed that the developed ANN models with R 2 values in the range of 0.878 to 0.990 had excellent performance in predicting all the output variables based on inputs. Energy consumption for processing of green tea, oolong tea, and black tea were calculated as 58,182, 60,947, and 66,301 MJ per ton of dry tea, respectively.

Overview of the CERT Resilience Management Model (CERT-RMM)

DTIC Science & Technology

2014-01-23

Management Model (CERT®-RMM) Jim Cebula Technical Manager - Cyber Risk Management , CERT® Division Jim Cebula is the Technical Manager of the...Cyber Risk Management team in the Cyber Security Solutions Directorate of the CERT Division at the Software Engineering Institute (SEI), a unit of...Carnegie Mellon University. Cebula’s current activities include risk management methods along with assessment and management of operational

Combating Terrorism Technical Support Office. 2008 Review

DTIC Science & Technology

2009-01-15

threat object displayed at the operator control unit of the robotic platform. Remote Utility Conversion Kit The Remote Utility Conversion Kit (RUCK) is a...three- dimensional and isometric simulations and games. Develop crowd models, adversarial behavior models, network-based simulations, mini-simulations...Craft-Littoral The modular unmanned surface craft-littoral ( MUSCL ) is a spin- off of EOD/LIC’s Unmanned Reconnaissance Observation Craft, developed

Probabilistic risk assessment of the Space Shuttle. Phase 3: A study of the potential of losing the vehicle during nominal operation. Volume 4: System models and data analysis

NASA Technical Reports Server (NTRS)

Fragola, Joseph R.; Maggio, Gaspare; Frank, Michael V.; Gerez, Luis; Mcfadden, Richard H.; Collins, Erin P.; Ballesio, Jorge; Appignani, Peter L.; Karns, James J.

1995-01-01

In this volume, volume 4 (of five volumes), the discussion is focussed on the system models and related data references and has the following subsections: space shuttle main engine, integrated solid rocket booster, orbiter auxiliary power units/hydraulics, and electrical power system.

1988 Revisions to the 1978 National Fire-Danger Rating System

Treesearch

Robert E. Burgan

1988-01-01

The 1978 National Fire-Danger Rating System does not work well in the humid environment of the Eastern United States. System modifications to correct problems and their operational impact on System users are described. A new set of 20 fuel models is defined and compared graphically with the 1978 fuel models. Technical documentation of System changes is provided.

Real-time emissions from construction equipment compared with model predictions.

PubMed

Heidari, Bardia; Marr, Linsey C

2015-02-01

The construction industry is a large source of greenhouse gases and other air pollutants. Measuring and monitoring real-time emissions will provide practitioners with information to assess environmental impacts and improve the sustainability of construction. We employed a portable emission measurement system (PEMS) for real-time measurement of carbon dioxide (CO), nitrogen oxides (NOx), hydrocarbon, and carbon monoxide (CO) emissions from construction equipment to derive emission rates (mass of pollutant emitted per unit time) and emission factors (mass of pollutant emitted per unit volume of fuel consumed) under real-world operating conditions. Measurements were compared with emissions predicted by methodologies used in three models: NONROAD2008, OFFROAD2011, and a modal statistical model. Measured emission rates agreed with model predictions for some pieces of equipment but were up to 100 times lower for others. Much of the difference was driven by lower fuel consumption rates than predicted. Emission factors during idling and hauling were significantly different from each other and from those of other moving activities, such as digging and dumping. It appears that operating conditions introduce considerable variability in emission factors. Results of this research will aid researchers and practitioners in improving current emission estimation techniques, frameworks, and databases.

Development and Use of a Web Site with Multimedia Contents as a Complement to Traditional Unit Operations Courses

ERIC Educational Resources Information Center

Tapia, Cristian; Muller, Mauricio; Sapag-Hagar, Jaime; Valenzuela, Fernando; Basualto, Carlos; Abugoch, Lilian

2005-01-01

The Unit Operations Laboratory offers 2 courses in unit operations. One is a 2-semester course for chemistry and food engineering students that is more demanding because it considers more unit operations and places more emphasis on solving exercises. The other is a 1-semester course for chemistry and pharmacy students that considers fewer unit…

Turbine and superheater bypass evaluation. Final report. [Faster startup in cycling operation and less erosion with steam bypass systems, including bypass design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosard, D.D.; Steltz, W.G.

1986-10-01

Properly sized turbine and boiler bypass systems permit two-shift cycling operation of units, shorten start-up time, and reduce life expenditures of plant components. With bypasses installed, faster startups can reduce fuel costs by $100,000 per year for a typical 500-MW fossil-fired unit. This report discusses the technical characteristics of existing bypass systems and provides guidelines for sizing bypass systems to achieve economical and reliable two-shift operation. The collection and analysis of startup data from several generating units were used in conjunction with computer simulations to illustrate the effects of adding various arrangements and sizes of steam bypass systems. The report,more » which indicates that shutdown procedures have significant impact on subsequent startup and loading time, describes operating practices to optimize the effectiveness of bypass systems. To determine the effectiveness of large turbine bypass systems of less than 100% capacity in preventing boiler trips following load rejection, transient field data were compared to a load rejection simulation using the modular modeling system (MMS). The MMS was then used to predict system response to other levels of load rejection. 7 refs., 87 figs., 8 tabs.« less

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

NASA Technical Reports Server (NTRS)

Padilla, Sebastian A.; Powers, Aaron; Iacomini, Christie S.; Paul, Heather L.

2011-01-01

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Ice Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously each the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU to the future flight unit are considered.

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

NASA Technical Reports Server (NTRS)

Padilla, Sebastian A.; Powers, Aaron; Iacomini, Christie S.; Bower, Chad E.; Paul, Heather L.

2012-01-01

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Icing Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU and the future flight unit are considered.

Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Y. H.; Jenne, D. S.; Thresher, R.

This report is an addendum to SAND2013-9040: Methodology for Design and Economic Analysis of Marine Energy Conversion (MEC) Technologies. This report describes an Oscillating Water Column Wave Energy Converter (OSWEC) reference model design in a complementary manner to Reference Models 1-4 contained in the above report. A conceptual design for a taut moored oscillating surge wave energy converter was developed. The design had an annual electrical power of 108 kilowatts (kW), rated power of 360 kW, and intended deployment at water depths between 50 m and 100 m. The study includes structural analysis, power output estimation, a hydraulic power conversionmore » chain system, and mooring designs. The results were used to estimate device capital cost and annual operation and maintenance costs. The device performance and costs were used for the economic analysis, following the methodology presented in SAND2013-9040 that included costs for designing, manufacturing, deploying, and operating commercial-scale MEC arrays up to 100 devices. The levelized cost of energy estimated for the Reference Model 5 OSWEC, presented in this report, was for a single device and arrays of 10, 50, and 100 units, and it enabled the economic analysis to account for cost reductions associated with economies of scale. The baseline commercial levelized cost of energy estimate for the Reference Model 5 device in an array comprised of 10 units is $1.44/kilowatt-hour (kWh), and the value drops to approximately $0.69/kWh for an array of 100 units.« less

40 CFR 60.2660 - What site-specific documentation is required?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training... and are suitable for inspection upon request. (1) Summary of the applicable standards under this...

40 CFR 60.2785 - What else must I report if I have a deviation from the requirement to have a qualified operator...

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF... Solid Waste Incineration Units Model Rule-Recordkeeping and Reporting § 60.2785 What else must I report...

40 CFR 60.2785 - What else must I report if I have a deviation from the requirement to have a qualified operator...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF... Solid Waste Incineration Units Model Rule-Recordkeeping and Reporting § 60.2785 What else must I report...

40 CFR 60.2660 - What site-specific documentation is required?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Operator Training... and are suitable for inspection upon request. (1) Summary of the applicable standards under this...

12 CFR 701.31 - Nondiscrimination requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... ORGANIZATION AND OPERATION OF FEDERAL CREDIT UNIONS § 701.31 Nondiscrimination requirements. (a) Definitions... words, symbols, models or other forms of communication that suggest a discriminatory preference or... in § 110.25(a) of the United States Department of Housing and Urban Development's (HUD) regulations...

Validating the Equilibrium Stage Model for an Azeotropic System in a Laboratorial Distillation Column

ERIC Educational Resources Information Center

Duarte, B. P. M.; Coelho Pinheiro, M. N.; Silva, D. C. M.; Moura, M. J.

2006-01-01

The experiment described is an excellent opportunity to apply theoretical concepts of distillation, thermodynamics of mixtures and process simulation at laboratory scale, and simultaneously enhance the ability of students to operate, control and monitor complex units.

40 CFR Table 3 to Subpart Ffff of... - Model Rule-Operating Limits for Incinerators and Wet Scrubbers

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Guidelines and Compliance Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 3 Table 3 to Subpart FFFF of Part 60...

40 CFR Table 3 to Subpart Ffff of... - Model Rule-Operating Limits for Incinerators and Wet Scrubbers

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Guidelines and Compliance Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 3 Table 3 to Subpart FFFF of Part 60...

40 CFR Table 3 to Subpart Ffff of... - Model Rule-Operating Limits for Incinerators and Wet Scrubbers

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Guidelines and Compliance Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 3 Table 3 to Subpart FFFF of Part 60...

An order insertion scheduling model of logistics service supply chain considering capacity and time factors.

PubMed

Liu, Weihua; Yang, Yi; Wang, Shuqing; Liu, Yang

2014-01-01

Order insertion often occurs in the scheduling process of logistics service supply chain (LSSC), which disturbs normal time scheduling especially in the environment of mass customization logistics service. This study analyses order similarity coefficient and order insertion operation process and then establishes an order insertion scheduling model of LSSC with service capacity and time factors considered. This model aims to minimize the average unit volume operation cost of logistics service integrator and maximize the average satisfaction degree of functional logistics service providers. In order to verify the viability and effectiveness of our model, a specific example is numerically analyzed. Some interesting conclusions are obtained. First, along with the increase of completion time delay coefficient permitted by customers, the possible inserting order volume first increases and then trends to be stable. Second, supply chain performance reaches the best when the volume of inserting order is equal to the surplus volume of the normal operation capacity in mass service process. Third, the larger the normal operation capacity in mass service process is, the bigger the possible inserting order's volume will be. Moreover, compared to increasing the completion time delay coefficient, improving the normal operation capacity of mass service process is more useful.

Computer-Aided Modeling and Analysis of Power Processing Systems (CAMAPPS), phase 1

NASA Technical Reports Server (NTRS)

Kim, S.; Lee, J.; Cho, B. H.; Lee, F. C.

1986-01-01

The large-signal behaviors of a regulator depend largely on the type of power circuit topology and control. Thus, for maximum flexibility, it is best to develop models for each functional block a independent modules. A regulator can then be configured by collecting appropriate pre-defined modules for each functional block. In order to complete the component model generation for a comprehensive spacecraft power system, the following modules were developed: solar array switching unit and control; shunt regulators; and battery discharger. The capability of each module is demonstrated using a simplified Direct Energy Transfer (DET) system. Large-signal behaviors of solar array power systems were analyzed. Stability of the solar array system operating points with a nonlinear load is analyzed. The state-plane analysis illustrates trajectories of the system operating point under various conditions. Stability and transient responses of the system operating near the solar array's maximum power point are also analyzed. The solar array system mode of operation is described using the DET spacecraft power system. The DET system is simulated for various operating conditions. Transfer of the software program CAMAPPS (Computer Aided Modeling and Analysis of Power Processing Systems) to NASA/GSFC (Goddard Space Flight Center) was accomplished.

Development of the pump protection system against cavitation on the basis of the stator current signature analysis of drive electric motor

NASA Astrophysics Data System (ADS)

Kipervasser, M. V.; Gerasimuk, A. V.; Simakov, V. P.

2018-05-01

In the present paper a new registration method of such inadmissible phenomenon as cavitation in the operating mode of centrifugal pump is offered. Influence of cavitation and extent of its development on the value of mechanical power consumed by the pump from the electric motor is studied. On the basis of design formulas the joint mathematical model of centrifugal pumping unit with the synchronous motor is created. In the model the phenomena accompanying the work of a pumping installation in the cavitation mode are considered. Mathematical modeling of the pump operation in the considered emergency operation is carried out. The chart of stator current of the electric motor, depending on the degree of cavitation development of is received. On the basis of the analysis of the obtained data the conclusion on the possibility of registration of cavitation by the current of drive electric motor is made and the functional diagram of the developed protection system is offered, its operation principle is described.

Advanced Technology Training System on Motor-Operated Valves

NASA Technical Reports Server (NTRS)

Wiederholt, Bradley J.; Widjaja, T. Kiki; Yasutake, Joseph Y.; Isoda, Hachiro

1993-01-01

This paper describes how features from the field of Intelligent Tutoring Systems are applied to the Motor-Operated Valve (MOV) Advanced Technology Training System (ATTS). The MOV ATTS is a training system developed at Galaxy Scientific Corporation for the Central Research Institute of Electric Power Industry in Japan and the Electric Power Research Institute in the United States. The MOV ATTS combines traditional computer-based training approaches with system simulation, integrated expert systems, and student and expert modeling. The primary goal of the MOV ATTS is to reduce human errors that occur during MOV overhaul and repair. The MOV ATTS addresses this goal by providing basic operational information of the MOV, simulating MOV operation, providing troubleshooting practice of MOV failures, and tailoring this training to the needs of each individual student. The MOV ATTS integrates multiple expert models (functional and procedural) to provide advice and feedback to students. The integration also provides expert model validation support to developers. Student modeling is supported by two separate student models: one model registers and updates the student's current knowledge of basic MOV information, while another model logs the student's actions and errors during troubleshooting exercises. These two models are used to provide tailored feedback to the student during the MOV course.

Pakistan Earthquake Relief Operations: Leveraging Humanitarian Missions for Strategic Success

DTIC Science & Technology

2010-12-01

PRISM 2, no. 1 leSSoNS leaRNed | 131 On Christmas morning 2005, at Saint Patrick’s Catholic Church in Auckland , New Zealand, a priest stepped up to... economically difficult to sustain. However, the HA/DR cam- paign in Pakistan, Operation Lifeline, provides a useful model of how humanitarian...35 The two field hospitals became symbols of the American-Pakistani military partnership and an asymmetric advantage for the United States as

Inverter performance comparison at PVUSA

NASA Astrophysics Data System (ADS)

Farmer, Brian K.; Stolte, Walter J.; Reyes, Antonio B.

1996-01-01

The paper is a summary of the Photovoltaics for Utility Scale Applications (PVUSA) Project's experience with procurement, testing, operation and maintenance of photovoltaic (PV) power conditioning units (PCUs) at the PVUSA Davis and Kerman sites. Brief descriptions of each of five different PCU models are included to explain tests and operational characteristics. A comparison of the PCUs' performances is presented, and conclusions are offered. Further details are in a forthcoming PVUSA report on PCUs and Power Quality [1].

Design of Training Systems. Computerization of the Educational Technology Assessment Model (ETAM). Volume 2

DTIC Science & Technology

1977-05-01

444 EN 2 31043 TEST UNIT INJECTORS AND/OR FUEL INJECTION NOZZLES 445 EN 2 31044 MAINTENANCE OF FUEL OIL INJECTORS 446 EN 2 31049 PREVENTION OF...OPERATIONAL MAINTENANCE OF DIESEL ENGINES OPERATE INTERNAL COMBUSTION ENGINES JACKING GEAR ON INTERNAL COMBUSTION ENGINES CARRYOUT TURNING OVER OF MAIN...ENGINES ALIGN LUBRICATING OIL SYSTEM USE OF STANDBY LUBRICATING OIL PUMPS PURGE DIESEL ENGINE FUEL INJECTION SYSTEM ENTRIES TO MAIN PROPULSION

Layering in peralkaline magmas, Ilímaussaq Complex, S Greenland

NASA Astrophysics Data System (ADS)

Hunt, Emma J.; Finch, Adrian A.; Donaldson, Colin H.

2017-01-01

The peralkaline to agpaitic Ilímaussaq Complex, S. Greenland, displays spectacular macrorhythmic (> 5 m) layering via the kakortokite (agpaitic nepheline syenite), which outcrops as the lowest exposed rocks in the complex. This study applies crystal size distribution (CSD) analyses and eudialyte-group mineral chemical compositions to study the marker horizon, Unit 0, and the contact to the underlying Unit - 1. Unit 0 is the best-developed unit in the kakortokites and as such is ideal for gaining insight into processes of crystal formation and growth within the layered kakortokite. The findings are consistent with a model whereby the bulk of the black and red layers developed through in situ crystallisation at the crystal mush-magma interface, whereas the white layer developed through a range of processes operating throughout the magma chamber, including density segregation (gravitational settling and flotation). Primary textures were modified through late-stage textural coarsening via grain overgrowth. An open-system model is proposed, where varying concentrations of halogens, in combination with undercooling, controlled crystal nucleation and growth to form Unit 0. Our observations suggest that the model is applicable more widely to the layering throughout the kakortokite series and potentially other layered peralkaline/agpaitic rocks around the world.

40 CFR 63.100 - Applicability and designation of source.

Code of Federal Regulations, 2010 CFR

2010-07-01

... manufacturing process unit has two or more products that have the same maximum annual design capacity on a mass... subject to this subpart. (3) For chemical manufacturing process units that are designed and operated as... chemical manufacturing process units that are designed and operated as flexible operation units shall be...

Field Performance of Heat Pump Water Heaters in the Northeast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shapiro, Carl; Puttagunta, Srikanth

2016-02-05

Heat pump water heaters (HPWHs) are finally entering the mainstream residential water heater market. Potential catalysts are increased consumer demand for higher energy efficiency electric water heating and a new Federal water heating standard that effectively mandates use of HPWHs for electric storage water heaters with nominal capacities greater than 55 gallons. When compared to electric resistance water heating, the energy and cost savings potential of HPWHs is tremendous. Converting all electric resistance water heaters to HPWHs could save American consumers 7.8 billion dollars annually ($182 per household) in water heating operating costs and cut annual residential source energy consumptionmore » for water heating by 0.70 quads. Steven Winter Associates, Inc. embarked on one of the first in situ studies of these newly released HPWH products through a partnership with two sponsoring electric utility companies, National Grid and NSTAR, and one sponsoring energy efficiency service program administrator, Cape Light Compact. Recent laboratory studies have measured performance of HPWHs under various operating conditions, but publically available field studies have not been as available. This evaluation attempts to provide publicly available field data on new HPWHs by monitoring the performance of three recently released products (General Electric GeoSpring(TM), A.O. Smith Voltex(R), and Stiebel Eltron Accelera(R) 300). Fourteen HPWHs were installed in Massachusetts and Rhode Island and monitored for over a year. Of the 14 units, ten were General Electric models (50 gallon units), two were Stiebel Eltron models (80 gallon units), and two were A.O. Smith models (one 60-gallon and one 80-gallon unit).« less

Operation Reliability Assessment for Cutting Tools by Applying a Proportional Covariate Model to Condition Monitoring Information

PubMed Central

Cai, Gaigai; Chen, Xuefeng; Li, Bing; Chen, Baojia; He, Zhengjia

2012-01-01

The reliability of cutting tools is critical to machining precision and production efficiency. The conventional statistic-based reliability assessment method aims at providing a general and overall estimation of reliability for a large population of identical units under given and fixed conditions. However, it has limited effectiveness in depicting the operational characteristics of a cutting tool. To overcome this limitation, this paper proposes an approach to assess the operation reliability of cutting tools. A proportional covariate model is introduced to construct the relationship between operation reliability and condition monitoring information. The wavelet packet transform and an improved distance evaluation technique are used to extract sensitive features from vibration signals, and a covariate function is constructed based on the proportional covariate model. Ultimately, the failure rate function of the cutting tool being assessed is calculated using the baseline covariate function obtained from a small sample of historical data. Experimental results and a comparative study show that the proposed method is effective for assessing the operation reliability of cutting tools. PMID:23201980

U.S. Army Delayed Entry Program Optimization Model

DTIC Science & Technology

2004-08-01

United States Military Academy West Point, New York 10996 OPERATIONS RESEARCH CENTER OF EXCELLENCE TECHNICAL REPORT No. DSE-TR- 0428 DTIC #: ADAXXXXX...following entries: Author(s) Department of Systems Engineering 2 Mahan Hall West Point, NY 10996 Client USAAC CAR 4 1307 Third Ave., Fort Knox, KY 40121...Wolter, LTC Michael J. Kwinn, Jr., LTC John Halstead DSE-R- 0428 5S. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8

Preliminary Findings of the South Africa Power System Capacity Expansion and Operational Modelling Study: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reber, Timothy J; Chartan, Erol Kevin; Brinkman, Gregory L

Wind and solar power contract prices have recently become cheaper than many conventional new-build alternatives in South Africa and trends suggest a continued increase in the share of variable renewable energy (vRE) on South Africa's power system with coal technology seeing the greatest reduction in capacity, see 'Figure 6: Percentage share by Installed Capacity (MW)' in [1]. Hence it is essential to perform a state-of-the-art grid integration study examining the effects of these high penetrations of vRE on South Africa's power system. Under the 21st Century Power Partnership (21CPP), funded by the U.S. Department of Energy, the National Renewable Energymore » Laboratory (NREL) has significantly augmented existing models of the South African power system to investigate future vRE scenarios. NREL, in collaboration with Eskom's Planning Department, further developed, tested and ran a combined capacity expansion and operational model of the South African power system including spatially disaggregated detail and geographical representation of system resources. New software to visualize and interpret modelling outputs has been developed, and scenario analysis of stepwise vRE build targets reveals new insight into associated planning and operational impacts and costs. The model, built using PLEXOS, is split into two components, firstly a capacity expansion model and secondly a unit commitment and economic dispatch model. The capacity expansion model optimizes new generation decisions to achieve the lowest cost, with a full understanding of capital cost and an approximated understanding of operational costs. The operational model has a greater set of detailed operational constraints and is run at daily resolutions. Both are run from 2017 through 2050. This investigation suggests that running both models in tandem may be the most effective means to plan the least cost South African power system as build plans seen to be more expensive than optimal by the capacity expansion model can produce greater operational cost savings seen only in the operational model.« less

Digital Gunnery: How Combat Vehicle Gunnery Training Creates a Model for Training the Mission Command System.

DTIC Science & Technology

2017-06-09

DIGITAL GUNNERY: HOW COMBAT VEHICLE GUNNERY TRAINING CREATES A MODEL FOR TRAINING THE MISSION COMMAND SYSTEM A thesis presented...Training Creates a Model for Training the Mission Command System 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S...digital systems that give commanders an unprecedented ability to understand and lead in the battlefields where they operate. Unfortunately, units

Modeling and Simulation for a Surf Zone Robot

DTIC Science & Technology

2012-12-14

of-freedom surf zone robot is developed and tested with a physical test platform and with a simulated robot in Robot Operating System . Derived from...terrain. The application of the model to future platforms is analyzed and a broad examination of the current state of surf zone robotic systems is...public release; distribution is unlimited MODELING AND SIMULATION FOR A SURF ZONE ROBOT Eric Shuey Lieutenant, United States Navy B.S., Systems

Preliminary development of digital signal processing in microwave radiometers

NASA Technical Reports Server (NTRS)

Stanley, W. D.

1980-01-01

Topics covered involve a number of closely related tasks including: the development of several control loop and dynamic noise model computer programs for simulating microwave radiometer measurements; computer modeling of an existing stepped frequency radiometer in an effort to determine its optimum operational characteristics; investigation of the classical second order analog control loop to determine its ability to reduce the estimation error in a microwave radiometer; investigation of several digital signal processing unit designs; initiation of efforts to develop required hardware and software for implementation of the digital signal processing unit; and investigation of the general characteristics and peculiarities of digital processing noiselike microwave radiometer signals.

Model of a programmable quantum processing unit based on a quantum transistor effect

NASA Astrophysics Data System (ADS)

Ablayev, Farid; Andrianov, Sergey; Fetisov, Danila; Moiseev, Sergey; Terentyev, Alexandr; Urmanchev, Andrey; Vasiliev, Alexander

2018-02-01

In this paper we propose a model of a programmable quantum processing device realizable with existing nano-photonic technologies. It can be viewed as a basis for new high performance hardware architectures. Protocols for physical implementation of device on the controlled photon transfer and atomic transitions are presented. These protocols are designed for executing basic single-qubit and multi-qubit gates forming a universal set. We analyze the possible operation of this quantum computer scheme. Then we formalize the physical architecture by a mathematical model of a Quantum Processing Unit (QPU), which we use as a basis for the Quantum Programming Framework. This framework makes it possible to perform universal quantum computations in a multitasking environment.

Determine Operating Reactor to Use for the 2016 PCI Level 1 Milestone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clarno, Kevin T.

2016-01-30

The Consortium for Advanced Simulation of Light Water Reactors (LWRs) (CASL) Level 1 milestone to “Assess the analysis capability for core-wide [pressurized water reactor] PWR Pellet- Clad Interaction (PCI) screening and demonstrate detailed 3-D analysis on selected sub-region” (L1:CASL.P13.03) requires a particular type of nuclear power plant for the assessment. This report documents the operating reactor and cycles chosen for this assessment in completion of the physics integration (PHI) milestone to “Determine Operating Reactor to use for PCI L1 Milestone” (L3:PHI.CMD.P12.02). Watts Bar Unit 1 experienced (at least) one fuel rod failure in each of cycles 6 and 7, andmore » at least one was deemed to be duty related rather than being primarily related to a manufacturing defect or grid effects. This brief report documents that the data required to model cycles 1–12 of Watts Bar Unit 1 using VERA-CS contains sufficient data to model the PHI portion of the PCI challenge problem. A list of additional data needs is also provided that will be important for verification and validation of the BISON results.« less

An Assessment of Hickam Air Force Base's Capability to Support Strategic Airlift Throughput when Operating under an Avian Flu Pandemic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brigantic, Robert T.; Campbell, James R.; Doctor, Pamela G.

Hickam Air Force Base (AFB), Hawaii provides an ideal waypoint for U.S. strategic airlift aircraft to refuel and receive other services on their way to Northeast and Southeast Asia from the continental United States. Hickam AFB also serves as a critical aerial port of debarkation (APOD) for deploying U.S. forces and equipment to more distant lands as needed. Making use of the United States Transportation Command’s Aerial Port of Debarkation Plus model, this paper examines the ability of Hickam AFB to serve in its important role as an APOD when operating under the effects of a major avian flu pandemic.more » In this regard, the major influence on Hickam AFB will be a serious degradation to the number of available personnel to service aircraft and operate Hickam AFB’s aerial port. It is noted that the results presented herein are based on simplistic attrition rate assumptions. Nonetheless, it is envisioned that this work is applicable to more realistic input attrition rates as avian flu epidemiological models are refined, as well as attrition associated with other types of contagious pandemic disease or willful biological warfare attack.« less

An Analysis of United States Marine Corps Enlisted Entry-Level Training Using Supply Chain and Operations Management

DTIC Science & Technology

2010-12-01

An Analysis of United States Marine Corps Enlisted Entry-Level Training Using Supply Chain and Operations Management ______________________________________ By...Report 4. TITLE AND SUBTITLE: An Analysis of United States Marine Corps Enlisted Entry-Level Training Using Supply Chain and Operations Management 6...Level Training; United States Marine Corps; Operations Management ; Supply Chain Management; Process Analysis 16. PRICE CODE 17. SECURITY

Use of the Legal-Institutional Analysis Model to assess hydropower licensing negotiations

USGS Publications Warehouse

Burkardt, N.; Lamb, B.L.; Lamb, B.L.; Garcia de Jalon, D.; Sabaton, C.; Souchon, Y.; Tamai, N.; Robinette, H.R.; Waddle, T.J.; Brinson, A.

2003-01-01

In the United States, the Federal Energy Regulatory Commission (FERC) is responsible for issuing or renewing licenses for hydropower projects owned and operated by power companies. During the licensing process, these companies are required to consult with agencies and other parties that are affected by project operating regimes. Typical participants include state and federal fish and wildlife agencies, environmental interest groups, and the FERC. One of the most difficult tasks facing participants is to reach agreement about what kinds of environmental conditions should be placed on license. Researchers at the United States Geological Survey developed a model to analyze the institutional context of natural resource disputes. The Legal-Institutional Analysis Model (LIAM) is a computerized model that allows an analyst to determine the likely behavior of each organization in a conflict. The model also analyzes the types and levels of negotiating power held by each organization. Researchers at the USGS have used the model in several cases involving hydropower license applications. To use the model, they facilitate workshops for stakeholder groups in order to develop a shared understanding of the likely obstacles and opportunities for successful resolution of the issues. This allows a systematic workshop analyses to develop strategies for successful negotiations, because they are able to better understand the negotiation problem and work more effectively with both their allies and their competitors.

76 FR 67425 - Availability of the Fiscal Year 2010 United States Special Operations Command (USSOCOM) Inventory...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-01

... Special Operations Command (USSOCOM) Inventory List of Contracts for Services; Correction AGENCY: United States Special Operations Command (USSOCOM), Department of Defense (DoD). ACTION: Notice of availability... Fiscal Year 2010 United States Special Operations Command (USSOCOM) Inventory List of Contracts for...

40 CFR 60.3014 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines... and qualification requirements? (a) No OSWI unit can be operated unless a fully trained and qualified... trained and qualified OSWI unit operator may operate the OSWI unit directly or be the direct supervisor of...

40 CFR 60.3014 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines... and qualification requirements? (a) No OSWI unit can be operated unless a fully trained and qualified... trained and qualified OSWI unit operator may operate the OSWI unit directly or be the direct supervisor of...

40 CFR 60.3014 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines... and qualification requirements? (a) No OSWI unit can be operated unless a fully trained and qualified... trained and qualified OSWI unit operator may operate the OSWI unit directly or be the direct supervisor of...

40 CFR 60.3014 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines... and qualification requirements? (a) No OSWI unit can be operated unless a fully trained and qualified... trained and qualified OSWI unit operator may operate the OSWI unit directly or be the direct supervisor of...

40 CFR 60.3014 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines... and qualification requirements? (a) No OSWI unit can be operated unless a fully trained and qualified... trained and qualified OSWI unit operator may operate the OSWI unit directly or be the direct supervisor of...

27 CFR 24.147 - Operations bond or unit bond.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Operations bond or unit... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Establishment and Operations Bonds and Consents of Surety § 24.147 Operations bond or unit bond. Notwithstanding the provisions of § 24.146, each person...

77 FR 11585 - Notice of Availability of the Aspinall Unit Operations Final Environmental Impact Statement...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-27

... Operations Final Environmental Impact Statement, Wayne N. Aspinall Unit, Colorado River Storage Project... SUMMARY: The Bureau of Reclamation (Reclamation), the Federal agency responsible for operation of the... Aspinall Unit operations, Gunnison and Montrose Counties, Colorado. DATES: Reclamation will not make a...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hong -Yi; Leung, L. Ruby; Tesfa, Teklu

A new large-scale stream temperature model has been developed within the Community Earth System Model (CESM) framework. The model is coupled with the Model for Scale Adaptive River Transport (MOSART) that represents river routing and a water management model (WM) that represents the effects of reservoir operations and water withdrawals on flow regulation. The coupled models allow the impacts of reservoir operations and withdrawals on stream temperature to be explicitly represented in a physically based and consistent way. The models have been applied to the Contiguous United States driven by observed meteorological forcing. It is shown that the model ismore » capable of reproducing stream temperature spatiotemporal variation satisfactorily by comparison against the observed streamflow from over 320 USGS stations. Including water management in the models improves the agreement between the simulated and observed streamflow at a large number of stream gauge stations. Both climate and water management are found to have important influence on the spatiotemporal patterns of stream temperature. More interestingly, it is quantitatively estimated that reservoir operation could cool down stream temperature in the summer low-flow season (August – October) by as much as 1~2oC over many places, as water management generally mitigates low flow, which has important implications to aquatic ecosystems. In conclusion, sensitivity of the simulated stream temperature to input data and reservoir operation rules used in the WM model motivates future directions to address some limitations in the current modeling framework.« less

Finite element analysis of heat generation from different light-polymerization sources during cementation of all-ceramic crowns.

PubMed

Tunc, Elif Pak

2007-06-01

Exothermic composite resin chemical reactions and visible light generators can produce heat during a restorative polymerization process. These thermal changes in restored teeth may cause pain and irreversible pulpitis. The purpose of this study was to analyze the temperature distribution and heat flow patterns of a crowned mandibular second premolar tooth model using 3 different light-polymerization technologies and a finite element technique. A 2-dimensional finite element model was used to simulate a clinical condition. Heat flow and thermal stress distribution in a tooth during cementation of an all-ceramic crown using 4 commercially available light-polymerization units (LPUs), each with different wavelengths (Elipar TriLight, Elipar Freelight, Apollo 95 E, and ADT 1000 PAC), were investigated. The temperature values were measured at 3, 10, 12, and 40 seconds for each light-polymerizing unit (LPU) at 6 different finite element nodes. Two-dimensional temporal and spatial distribution of the thermal stress within the tooth, including the thermal coefficients and boundary conditions of the dental materials, were obtained and evaluated. The temperature at the nodal points did not exceed 42 degrees C, which is a threshold value for tissue vitality within the recommended operating periods at the dentin and pulp surface for all LPUs, except for Elipar TriLight. In the case of Elipar TriLlight, the temperatures at the dentin and pulp surfaces were 47 degrees C and 42 degrees C, respectively. When the light-polymerization units were used according to the manufacturers' operating procedures and without prolonged operating periods, with the exception of Elipar TriLight, the investigated LPUs did not produce significant heat. However, when the operating periods were prolonged, unacceptable temperature increases were observed, especially with the high-intensity LPUs.

The Design and Analysis of a Novel Split-H-Shaped Metamaterial for Multi-Band Microwave Applications

PubMed Central

Islam, Sikder Sunbeam; Faruque, Mohammad Rashed Iqbal; Islam, Mohammad Tariqul

2014-01-01

This paper presents the design and analysis of a novel split-H-shaped metamaterial unit cell structure that is applicable in a multi-band frequency range and that exhibits negative permeability and permittivity in those frequency bands. In the basic design, the separate split-square resonators are joined by a metal link to form an H-shaped unit structure. Moreover, an analysis and a comparison of the 1 × 1 array and 2 × 2 array structures and the 1 × 1 and 2 × 2 unit cell configurations were performed. All of these configurations demonstrate multi-band operating frequencies (S-band, C-band, X-band and Ku-band) with double-negative characteristics. The equivalent circuit model and measured result for each unit cell are presented to validate the resonant behavior. The commercially available finite-difference time-domain (FDTD)-based simulation software, Computer Simulation Technology (CST) Microwave Studio, was used to obtain the reflection and transmission parameters of each unit cell. This is a novel and promising design in the electromagnetic paradigm for its simplicity, scalability, double-negative characteristics and multi-band operation. PMID:28788116

The Design and Analysis of a Novel Split-H-Shaped Metamaterial for Multi-Band Microwave Applications.

PubMed

Islam, Sikder Sunbeam; Faruque, Mohammad Rashed Iqbal; Islam, Mohammad Tariqul

2014-07-02

This paper presents the design and analysis of a novel split-H-shaped metamaterial unit cell structure that is applicable in a multi-band frequency range and that exhibits negative permeability and permittivity in those frequency bands. In the basic design, the separate split-square resonators are joined by a metal link to form an H-shaped unit structure. Moreover, an analysis and a comparison of the 1 × 1 array and 2 × 2 array structures and the 1 × 1 and 2 × 2 unit cell configurations were performed. All of these configurations demonstrate multi-band operating frequencies (S-band, C-band, X-band and K u -band) with double-negative characteristics. The equivalent circuit model and measured result for each unit cell are presented to validate the resonant behavior. The commercially available finite-difference time-domain (FDTD)-based simulation software, Computer Simulation Technology (CST) Microwave Studio, was used to obtain the reflection and transmission parameters of each unit cell. This is a novel and promising design in the electromagnetic paradigm for its simplicity, scalability, double-negative characteristics and multi-band operation.

Modeling, control, and dynamic performance analysis of a reverse osmosis desalination plant integrated within hybrid energy systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Jong Suk; Chen, Jun; Garcia, Humberto E.

An RO (reverse osmosis) desalination plant is proposed as an effective, FLR (flexible load resource) to be integrated into HES (hybrid energy systems) to support various types of ancillary services to the electric grid, under variable operating conditions. To study the dynamic (transient) analysis of such system, among the various unit operations within HES, special attention is given here to the detailed dynamic modeling and control design of RO desalination process with a spiral-wound membrane module. The model incorporates key physical phenomena that have been investigated individually into a dynamic integrated model framework. In particular, the solution-diffusion model modified withmore » the concentration polarization theory is applied to predict RO performance over a large range of operating conditions. Simulation results involving several case studies suggest that an RO desalination plant, acting as a FLR, can provide operational flexibility to participate in energy management at the utility scale by dynamically optimizing the use of excess electrical energy. Here, the incorporation of additional commodity (fresh water) produced from a FLR allows a broader range of HES operations for maximizing overall system performance and profitability. For the purpose of assessing the incorporation of health assessment into process operations, an online condition monitoring approach for RO membrane fouling supervision is addressed in the case study presented.« less

Modeling, control, and dynamic performance analysis of a reverse osmosis desalination plant integrated within hybrid energy systems

DOE PAGES

Kim, Jong Suk; Chen, Jun; Garcia, Humberto E.

2016-06-17

An RO (reverse osmosis) desalination plant is proposed as an effective, FLR (flexible load resource) to be integrated into HES (hybrid energy systems) to support various types of ancillary services to the electric grid, under variable operating conditions. To study the dynamic (transient) analysis of such system, among the various unit operations within HES, special attention is given here to the detailed dynamic modeling and control design of RO desalination process with a spiral-wound membrane module. The model incorporates key physical phenomena that have been investigated individually into a dynamic integrated model framework. In particular, the solution-diffusion model modified withmore » the concentration polarization theory is applied to predict RO performance over a large range of operating conditions. Simulation results involving several case studies suggest that an RO desalination plant, acting as a FLR, can provide operational flexibility to participate in energy management at the utility scale by dynamically optimizing the use of excess electrical energy. Here, the incorporation of additional commodity (fresh water) produced from a FLR allows a broader range of HES operations for maximizing overall system performance and profitability. For the purpose of assessing the incorporation of health assessment into process operations, an online condition monitoring approach for RO membrane fouling supervision is addressed in the case study presented.« less

Ensemble Flow Forecasts for Risk Based Reservoir Operations of Lake Mendocino in Mendocino County, California

NASA Astrophysics Data System (ADS)

Delaney, C.; Hartman, R. K.; Mendoza, J.; Evans, K. M.; Evett, S.

2016-12-01

Forecast informed reservoir operations (FIRO) is a methodology that incorporates short to mid-range precipitation or flow forecasts to inform the flood operations of reservoirs. Previous research and modeling for flood control reservoirs has shown that FIRO can reduce flood risk and increase water supply for many reservoirs. The risk-based method of FIRO presents a unique approach that incorporates flow forecasts made by NOAA's California-Nevada River Forecast Center (CNRFC) to model and assess risk of meeting or exceeding identified management targets or thresholds. Forecasted risk is evaluated against set risk tolerances to set reservoir flood releases. A water management model was developed for Lake Mendocino, a 116,500 acre-foot reservoir located near Ukiah, California. Lake Mendocino is a dual use reservoir, which is owned and operated for flood control by the United State Army Corps of Engineers and is operated by the Sonoma County Water Agency for water supply. Due to recent changes in the operations of an upstream hydroelectric facility, this reservoir has been plagued with water supply reliability issues since 2007. FIRO is applied to Lake Mendocino by simulating daily hydrologic conditions from 1985 to 2010 in the Upper Russian River from Lake Mendocino to the City of Healdsburg approximately 50 miles downstream. The risk-based method is simulated using a 15-day, 61 member streamflow hindcast by the CNRFC. Model simulation results of risk-based flood operations demonstrate a 23% increase in average end of water year (September 30) storage levels over current operations. Model results show no increase in occurrence of flood damages for points downstream of Lake Mendocino. This investigation demonstrates that FIRO may be a viable flood control operations approach for Lake Mendocino and warrants further investigation through additional modeling and analysis.

Cooling tower plume - model and experiment

NASA Astrophysics Data System (ADS)

Cizek, Jan; Gemperle, Jiri; Strob, Miroslav; Nozicka, Jiri

The paper discusses the description of the simple model of the, so-called, steam plume, which in many cases forms during the operation of the evaporative cooling systems of the power plants, or large technological units. The model is based on semi-empirical equations that describe the behaviour of a mixture of two gases in case of the free jet stream. In the conclusion of the paper, a simple experiment is presented through which the results of the designed model shall be validated in the subsequent period.

Biophysically Based Mathematical Modeling of Interstitial Cells of Cajal Slow Wave Activity Generated from a Discrete Unitary Potential Basis

PubMed Central

Faville, R.A.; Pullan, A.J.; Sanders, K.M.; Koh, S.D.; Lloyd, C.M.; Smith, N.P.

2009-01-01

Abstract Spontaneously rhythmic pacemaker activity produced by interstitial cells of Cajal (ICC) is the result of the entrainment of unitary potential depolarizations generated at intracellular sites termed pacemaker units. In this study, we present a mathematical modeling framework that quantitatively represents the transmembrane ion flows and intracellular Ca2+ dynamics from a single ICC operating over the physiological membrane potential range. The mathematical model presented here extends our recently developed biophysically based pacemaker unit modeling framework by including mechanisms necessary for coordinating unitary potential events, such as a T-Type Ca2+ current, Vm-dependent K+ currents, and global Ca2+ diffusion. Model simulations produce spontaneously rhythmic slow wave depolarizations with an amplitude of 65 mV at a frequency of 17.4 cpm. Our model predicts that activity at the spatial scale of the pacemaker unit is fundamental for ICC slow wave generation, and Ca2+ influx from activation of the T-Type Ca2+ current is required for unitary potential entrainment. These results suggest that intracellular Ca2+ levels, particularly in the region local to the mitochondria and endoplasmic reticulum, significantly influence pacing frequency and synchronization of pacemaker unit discharge. Moreover, numerical investigations show that our ICC model is capable of qualitatively replicating a wide range of experimental observations. PMID:19527643

Short-term bulk energy storage system scheduling for load leveling in unit commitment: modeling, optimization, and sensitivity analysis

PubMed Central

Hemmati, Reza; Saboori, Hedayat

2016-01-01

Energy storage systems (ESSs) have experienced a very rapid growth in recent years and are expected to be a promising tool in order to improving power system reliability and being economically efficient. The ESSs possess many potential benefits in various areas in the electric power systems. One of the main benefits of an ESS, especially a bulk unit, relies on smoothing the load pattern by decreasing on-peak and increasing off-peak loads, known as load leveling. These devices require new methods and tools in order to model and optimize their effects in the power system studies. In this respect, this paper will model bulk ESSs based on the several technical characteristics, introduce the proposed model in the thermal unit commitment (UC) problem, and analyze it with respect to the various sensitive parameters. The technical limitations of the thermal units and transmission network constraints are also considered in the model. The proposed model is a Mixed Integer Linear Programming (MILP) which can be easily solved by strong commercial solvers (for instance CPLEX) and it is appropriate to be used in the practical large scale networks. The results of implementing the proposed model on a test system reveal that proper load leveling through optimum storage scheduling leads to considerable operation cost reduction with respect to the storage system characteristics. PMID:27222741

Short-term bulk energy storage system scheduling for load leveling in unit commitment: modeling, optimization, and sensitivity analysis.

PubMed

Hemmati, Reza; Saboori, Hedayat

2016-05-01

Energy storage systems (ESSs) have experienced a very rapid growth in recent years and are expected to be a promising tool in order to improving power system reliability and being economically efficient. The ESSs possess many potential benefits in various areas in the electric power systems. One of the main benefits of an ESS, especially a bulk unit, relies on smoothing the load pattern by decreasing on-peak and increasing off-peak loads, known as load leveling. These devices require new methods and tools in order to model and optimize their effects in the power system studies. In this respect, this paper will model bulk ESSs based on the several technical characteristics, introduce the proposed model in the thermal unit commitment (UC) problem, and analyze it with respect to the various sensitive parameters. The technical limitations of the thermal units and transmission network constraints are also considered in the model. The proposed model is a Mixed Integer Linear Programming (MILP) which can be easily solved by strong commercial solvers (for instance CPLEX) and it is appropriate to be used in the practical large scale networks. The results of implementing the proposed model on a test system reveal that proper load leveling through optimum storage scheduling leads to considerable operation cost reduction with respect to the storage system characteristics.

Homeland Security Interagency Support. (Joint Center for Lessons Learned Quarterly Bulletin. Volume 4, Issue 2, March 2002)

DTIC Science & Technology

2002-03-01

sections consists of four units, the Domestic Terrorism Operations Unit, the WMD Operations Unit, the WMD Countermeasures Unit, and Special Events Management Unit...Countermeasures Unit Chief Special Events Management Unit Chief Domestic Terrorism/ Counterterrorism Section Chief International Terrorism Section Asstistant

NASA's Evolutionary Xenon Thruster (NEXT) Prototype Model 1R (PM1R) Ion Thruster and Propellant Management System Wear Test Results

NASA Technical Reports Server (NTRS)

VanNoord, Jonathan L.; Soulas, George C.; Sovey, James S.

2010-01-01

The results of the NEXT wear test are presented. This test was conducted with a 36-cm ion engine (designated PM1R) and an engineering model propellant management system. The thruster operated with beam extraction for a total of 1680 hr and processed 30.5 kg of xenon during the wear test, which included performance testing and some operation with an engineering model power processing unit. A total of 1312 hr was accumulated at full power, 277 hr at low power, and the remainder was at intermediate throttle levels. Overall ion engine performance, which includes thrust, thruster input power, specific impulse, and thrust efficiency, was steady with no indications of performance degradation. The propellant management system performed without incident during the wear test. The ion engine and propellant management system were also inspected following the test with no indication of anomalous hardware degradation from operation.

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

Analysis of transit contracting models and proper incentives for long-term success.

DOT National Transportation Integrated Search

2013-11-01

As transit systems are being challenged to operate in the most cost-effective manner, and budgets are being tightened and demand for services increases, there has been renewed interest in the area of contracting for fixed route service in the United ...

40 CFR 60.2775 - What else must I report if I have a deviation from the operating limits or the emission limitations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR... Waste Incineration Units Model Rule-Recordkeeping and Reporting § 60.2775 What else must I report if I...

40 CFR 60.2775 - What else must I report if I have a deviation from the operating limits or the emission limitations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR... Waste Incineration Units Model Rule-Recordkeeping and Reporting § 60.2775 What else must I report if I...

77 FR 5991 - Airworthiness Directives; Eurocopter France Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-07

... Airworthiness Directives; Eurocopter France Helicopters AGENCY: Federal Aviation Administration (FAA... airworthiness directive (AD) for the Eurocopter France (ECF) Model AS332L2 helicopter and superseding an AD for... of France and are approved for operation in the United States. Pursuant to our bilateral agreement...

APPLICATIONS OF A CONCEPTUAL MODEL (THE BIOLOGICAL CONDITION GRADIENT) TO DEFINE AQUATIC REFERENCE CONDITIONS

EPA Science Inventory

The United States Clean Water Act currently offers no definitions to interpret the Act's objective to "restore and maintain physical, chemical and biological integrity of the Nation's waters". Operative definitions, independent of differences in assessment methodologies, are nee...

46 CFR 161.002-18 - Method of application for type approval.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the system's instruction manual, including information concerning installation, programming, operation... section. (4) Three copies of a list prepared by the manufacturer that contains the name, model number, and... cabinet, detector, zone card, isolator, central processing unit, zener barrier, special purpose module, or...

A Computer Model of the Evaporator for the Development of an Automatic Control System

NASA Astrophysics Data System (ADS)

Kozin, K. A.; Efremov, E. V.; Kabrysheva, O. P.; Grachev, M. I.

2016-08-01

For the implementation of a closed nuclear fuel cycle it is necessary to carry out a series of experimental studies to justify the choice of technology. In addition, the operation of the radiochemical plant is impossible without high-quality automatic control systems. In the technologies of spent nuclear fuel reprocessing, the method of continuous evaporation is often used for a solution conditioning. Therefore, the effective continuous technological process will depend on the operation of the evaporation equipment. Its essential difference from similar devices is a small size. In this paper the method of mathematic simulation is applied for the investigation of one-effect evaporator with an external heating chamber. Detailed modelling is quite difficult because the phase equilibrium dynamics of the evaporation process is not described. Moreover, there is a relationship with the other process units. The results proved that the study subject is a MIMO plant, nonlinear over separate control channels and not selfbalancing. Adequacy was tested using the experimental data obtained at the laboratory evaporation unit.

Self-organization of network dynamics into local quantized states.

PubMed

Nicolaides, Christos; Juanes, Ruben; Cueto-Felgueroso, Luis

2016-02-17

Self-organization and pattern formation in network-organized systems emerges from the collective activation and interaction of many interconnected units. A striking feature of these non-equilibrium structures is that they are often localized and robust: only a small subset of the nodes, or cell assembly, is activated. Understanding the role of cell assemblies as basic functional units in neural networks and socio-technical systems emerges as a fundamental challenge in network theory. A key open question is how these elementary building blocks emerge, and how they operate, linking structure and function in complex networks. Here we show that a network analogue of the Swift-Hohenberg continuum model-a minimal-ingredients model of nodal activation and interaction within a complex network-is able to produce a complex suite of localized patterns. Hence, the spontaneous formation of robust operational cell assemblies in complex networks can be explained as the result of self-organization, even in the absence of synaptic reinforcements.

Reliability analysis and fault-tolerant system development for a redundant strapdown inertial measurement unit. [inertial platforms

NASA Technical Reports Server (NTRS)

Motyka, P.

1983-01-01

A methodology is developed and applied for quantitatively analyzing the reliability of a dual, fail-operational redundant strapdown inertial measurement unit (RSDIMU). A Markov evaluation model is defined in terms of the operational states of the RSDIMU to predict system reliability. A 27 state model is defined based upon a candidate redundancy management system which can detect and isolate a spectrum of failure magnitudes. The results of parametric studies are presented which show the effect on reliability of the gyro failure rate, both the gyro and accelerometer failure rates together, false alarms, probability of failure detection, probability of failure isolation, and probability of damage effects and mission time. A technique is developed and evaluated for generating dynamic thresholds for detecting and isolating failures of the dual, separated IMU. Special emphasis is given to the detection of multiple, nonconcurrent failures. Digital simulation time histories are presented which show the thresholds obtained and their effectiveness in detecting and isolating sensor failures.

Store-operate-coherence-on-value

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Heidelberger, Philip; Kumar, Sameer

A system, method and computer program product for performing various store-operate instructions in a parallel computing environment that includes a plurality of processors and at least one cache memory device. A queue in the system receives, from a processor, a store-operate instruction that specifies under which condition a cache coherence operation is to be invoked. A hardware unit in the system runs the received store-operate instruction. The hardware unit evaluates whether a result of the running the received store-operate instruction satisfies the condition. The hardware unit invokes a cache coherence operation on a cache memory address associated with the receivedmore » store-operate instruction if the result satisfies the condition. Otherwise, the hardware unit does not invoke the cache coherence operation on the cache memory device.« less

Dynamical Localization for Unitary Anderson Models

NASA Astrophysics Data System (ADS)

Hamza, Eman; Joye, Alain; Stolz, Günter

2009-11-01

This paper establishes dynamical localization properties of certain families of unitary random operators on the d-dimensional lattice in various regimes. These operators are generalizations of one-dimensional physical models of quantum transport and draw their name from the analogy with the discrete Anderson model of solid state physics. They consist in a product of a deterministic unitary operator and a random unitary operator. The deterministic operator has a band structure, is absolutely continuous and plays the role of the discrete Laplacian. The random operator is diagonal with elements given by i.i.d. random phases distributed according to some absolutely continuous measure and plays the role of the random potential. In dimension one, these operators belong to the family of CMV-matrices in the theory of orthogonal polynomials on the unit circle. We implement the method of Aizenman-Molchanov to prove exponential decay of the fractional moments of the Green function for the unitary Anderson model in the following three regimes: In any dimension, throughout the spectrum at large disorder and near the band edges at arbitrary disorder and, in dimension one, throughout the spectrum at arbitrary disorder. We also prove that exponential decay of fractional moments of the Green function implies dynamical localization, which in turn implies spectral localization. These results complete the analogy with the self-adjoint case where dynamical localization is known to be true in the same three regimes.

Operational Space Weather Activities in the US

NASA Astrophysics Data System (ADS)

Berger, Thomas; Singer, Howard; Onsager, Terrance; Viereck, Rodney; Murtagh, William; Rutledge, Robert

2016-07-01

We review the current activities in the civil operational space weather forecasting enterprise of the United States. The NOAA/Space Weather Prediction Center is the nation's official source of space weather watches, warnings, and alerts, working with partners in the Air Force as well as international operational forecast services to provide predictions, data, and products on a large variety of space weather phenomena and impacts. In October 2015, the White House Office of Science and Technology Policy released the National Space Weather Strategy (NSWS) and associated Space Weather Action Plan (SWAP) that define how the nation will better forecast, mitigate, and respond to an extreme space weather event. The SWAP defines actions involving multiple federal agencies and mandates coordination and collaboration with academia, the private sector, and international bodies to, among other things, develop and sustain an operational space weather observing system; develop and deploy new models of space weather impacts to critical infrastructure systems; define new mechanisms for the transition of research models to operations and to ensure that the research community is supported for, and has access to, operational model upgrade paths; and to enhance fundamental understanding of space weather through support of research models and observations. The SWAP will guide significant aspects of space weather operational and research activities for the next decade, with opportunities to revisit the strategy in the coming years through the auspices of the National Science and Technology Council.

Productivity Analysis of Public and Private Airports: A Causal Investigation

NASA Technical Reports Server (NTRS)

Vasigh, Bijan; Gorjidooz, Javad

2007-01-01

Around the world, airports are being viewed as enterprises, rather than public services, which are expected to be managed efficiently and provide passengers with courteous customer services. Governments are, increasingly, turning to the private sectors for their efficiency in managing the operation, financing, and development, as well as providing security for airports. Operational and financial performance evaluation has become increasingly important to airport operators due to recent trends in airport privatization. Assessing performance allows the airport operators to plan for human resources and capital investment as efficiently as possible. Productivity measurements may be used as comparisons and guidelines in strategic planning, in the internal analysis of operational efficiency and effectiveness, and in assessing the competitive position of an airport in transportation industry. The primary purpose of this paper is to investigate the operational and financial efficiencies of 22 major airports in the United States and Europe. These airports are divided into three groups based on private ownership (7 British Airport Authority airports), public ownership (8 major United States airports), and a mix of private and public ownership (7 major European Union airports. The detail ownership structures of these airports are presented in Appendix A. Total factor productivity (TFP) model was utilized to measure airport performance in terms of financial and operational efficiencies and to develop a benchmarking tool to identify the areas of strength and weakness. A regression model was then employed to measure the relationship between TFP and ownership structure. Finally a Granger causality test was performed to determine whether ownership structure is a Granger cause of TFP. The results of the analysis presented in this paper demonstrate that there is not a significant relationship between airport TFP and ownership structure. Airport productivity and efficiency is, however dependent upon the level of competition, choice of the market, and regulatory control.

40 CFR 60.2905 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... OSWI unit can be operated unless a fully trained and qualified OSWI unit operator is accessible, either... may operate the OSWI unit directly or be the direct supervisor of one or more other plant personnel...

40 CFR 60.2905 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of... OSWI unit can be operated unless a fully trained and qualified OSWI unit operator is accessible, either... may operate the OSWI unit directly or be the direct supervisor of one or more other plant personnel...

A Microprocessor-Controlled Data Acquisition System for the Federal Scientific Model UA-500-1 Ubiquitous Spectrum Analyzer

DTIC Science & Technology

1976-09-01

Model AN/ UGC -59A teletype and paper-tape punch console. This unit is connected with the Intellec 8 computer and punching operations are controlled by...order to use this program, the microprocessor would have to be one of the many types on the market that make use of the INTEL 8008-1 CPD chip. The use

A guide to the TWIGS program for the North Central United States.

Treesearch

Cynthia L. Miner; Nancy R. Walters; Monique L. Belli

1988-01-01

This is a complete reference to TWIGS, a forest growth-and-yield program with management and economic components developed for Lake and Central States tree species. The guide describes how TWIGS models growth and yield and how the model can be applied to obtain the best results. Step-by-step operating instructions are provided for TWIGS and its companion program,...

A wildfire risk modeling system for evaluating landscape fuel treatment strategies

Treesearch

Alan Ager; Mark Finney; Andrew McMahan

2006-01-01

Despite a wealth of literature and models concerning wildfire risk, field units in Federal land management agencies lack a clear framework and operational tools to measure how risk might change from proposed fuel treatments. In an actuarial context, risk is defined as the expected value change from a fire, calculated as the product of (1) probability of a fire at a...

Landscape-and regional-scale shifts in forest composition under climate change in the Central Hardwood Region of the United States

Treesearch

Wen J. Wang; Hong S. He; Frank R. Thompson; Jacob S. Fraser; William D. Dijak

2016-01-01

Tree species distribution and abundance are affected by forces operating at multiple scales. Niche and biophysical process models have been commonly used to predict climate change effects at regional scales, however, these models have limited capability to include site-scale population dynamics and landscape- scale disturbance and dispersal. We applied a landscape...

75 FR 4475 - Airworthiness Directives; Eurocopter France Model AS332L1, AS332L2, and EC225LP Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-28

... Airworthiness Directives; Eurocopter France Model AS332L1, AS332L2, and EC225LP Helicopters AGENCY: Federal.... SUMMARY: We are adopting a new airworthiness directive (AD) for the specified Eurocopter France (ECF... France and are approved for operation in the United States. Pursuant to our bilateral [[Page 4476...

A Model for the Determination of the Costs of Special Education as Compared with That for General Education. Appendix: Part 2.

ERIC Educational Resources Information Center

Ernst and Ernst, Chicago, IL.

Part 2 of the appendix to "A Model for the Determination of the Costs of Special Education as Compared with That for General Education" contains information on using 10-minute units of service measure in Ernstville, a hypothetical school district conceived to illustrate operation of a proposed cost accounting system. (LH)

Transient Pressure Measurements in the Vaneless Space of a Francis Turbine during Load Acceptances from Minimum Load

NASA Astrophysics Data System (ADS)

Goyal, R.; Gandhi, B. K.; Cervantes, M. J.

2018-06-01

Increased penetration of solar and the wind impels the designers of the hydroelectric power generation unit to provide more flexibility in operation for the stability of the grid. The power generating unit includes turbine which needs to sustain sudden change in its operating conditions. Thus, the hydraulic turbine experiences more transients per day which result in chronic problems such as fatigue to the runner, instrument malfunctioning, vibrations, wear and tear etc. This paper describes experiments performed on a high model (1.5:1) Francis turbine for load acceptances from the minimum load. The experiments presented in the paper are the part of Francis-99 workshop which aims to determine the performance of numerical models in simulations of model Francis turbine under steady and transient operating conditions. The aim of the paper is to present the transient pressure variation in the vaneless space of a Francis turbine where high-frequency pulsations are normally expected. For this, two pressure sensors, VL1 and VL2, are mounted at the vaneless space, one near the beginning of the spiral casing and the other before the end of the spiral casing. Both are used to capture the unsteady pressure field developed in the space between guide vanes and runner inlet. The time-resolved pressure signals are analyzed and presented during the transient to observe the pressure variation and dominant frequencies of pulsations.

A model to create an efficient and equitable admission policy for patients arriving to the cardiothoracic ICU.

PubMed

Yang, Muer; Fry, Michael J; Raikhelkar, Jayashree; Chin, Cynthia; Anyanwu, Anelechi; Brand, Jordan; Scurlock, Corey

2013-02-01

To develop queuing and simulation-based models to understand the relationship between ICU bed availability and operating room schedule to maximize the use of critical care resources and minimize case cancellation while providing equity to patients and surgeons. Retrospective analysis of 6-month unit admission data from a cohort of cardiothoracic surgical patients, to create queuing and simulation-based models of ICU bed flow. Three different admission policies (current admission policy, shortest-processing-time policy, and a dynamic policy) were then analyzed using simulation models, representing 10 yr worth of potential admissions. Important output data consisted of the "average waiting time," a proxy for unit efficiency, and the "maximum waiting time," a surrogate for patient equity. A cardiothoracic surgical ICU in a tertiary center in New York, NY. Six hundred thirty consecutive cardiothoracic surgical patients admitted to the cardiothoracic surgical ICU. None. Although the shortest-processing-time admission policy performs best in terms of unit efficiency (0.4612 days), it did so at expense of patient equity prolonging surgical waiting time by as much as 21 days. The current policy gives the greatest equity but causes inefficiency in unit bed-flow (0.5033 days). The dynamic policy performs at a level (0.4997 days) 8.3% below that of the shortest-processing-time in average waiting time; however, it balances this with greater patient equity (maximum waiting time could be shortened by 4 days compared to the current policy). Queuing theory and computer simulation can be used to model case flow through a cardiothoracic operating room and ICU. A dynamic admission policy that looks at current waiting time and expected ICU length of stay allows for increased equity between patients with only minimum losses of efficiency. This dynamic admission policy would seem to be a superior in maximizing case-flow. These results may be generalized to other surgical ICUs.

Modelling daily dissolved oxygen concentration using least square support vector machine, multivariate adaptive regression splines and M5 model tree

NASA Astrophysics Data System (ADS)

Heddam, Salim; Kisi, Ozgur

2018-04-01

In the present study, three types of artificial intelligence techniques, least square support vector machine (LSSVM), multivariate adaptive regression splines (MARS) and M5 model tree (M5T) are applied for modeling daily dissolved oxygen (DO) concentration using several water quality variables as inputs. The DO concentration and water quality variables data from three stations operated by the United States Geological Survey (USGS) were used for developing the three models. The water quality data selected consisted of daily measured of water temperature (TE, °C), pH (std. unit), specific conductance (SC, μS/cm) and discharge (DI cfs), are used as inputs to the LSSVM, MARS and M5T models. The three models were applied for each station separately and compared to each other. According to the results obtained, it was found that: (i) the DO concentration could be successfully estimated using the three models and (ii) the best model among all others differs from one station to another.

Development of an advanced anaerobic digester design and a kinetic model for biogasification of water hyacinth/sludge blends

DOE Office of Scientific and Technical Information (OSTI.GOV)

Srivastava, V.; Fannin, K.F.; Biljetina, R.

1986-07-01

The Institute of Gas Technology (IGT) conducted a comprehensive laboratory-scale research program to develop and optimize the anaerobic digestion process for producing methane from water hyacinth and sludge blends. This study focused on digester design and operating techniques, which gave improved methane yields and production rates over those observed using conventional digesters. The final digester concept and the operating experience was utilized to design and operate a large-scale experimentla test unit (ETU) at Walt Disney World, Florida. This paper describes the novel digester design, operating techniques, and the results obtained in the laboratory. The paper also discusses a kinetic modelmore » which predicts methane yield, methane production rate, and digester effluent solids as a function of retention time. This model was successfully utilized to predict the performance of the ETU. 15 refs., 6 figs., 6 tabs.« less

Evaluation and Strategic Planning for the GLOBE Program

NASA Astrophysics Data System (ADS)

Geary, E. E.; Williams, V. L.

2010-12-01

The Global Learning and Observations to Benefit the Environment (GLOBE) Program is an international environmental education program. It unites educators, students and scientists worldwide to collaborate on inquiry based investigations of the environment and Earth system science. Evaluation of the GLOBE program has been challenging because of its broad reach, diffuse models of implementation, and multiple stakeholders. In an effort to guide current evaluation efforts, a logic model was developed that provides a visual display of how the GLOBE program operates. Using standard elements of inputs, activities, outputs, customers and outcomes, this model describes how the program operates to achieve its goals. The template used to develop this particular logic model aligns the GLOBE program operations with its program strategy, thus ensuring that what the program is doing supports the achievement of long-term, intermediate and annual goals. It also provides a foundation for the development of key programmatic metrics that can be used to gauge progress toward the achievement of strategic goals.

Climate Change Impacts on Stream Temperature in Regulated River Systems: A Case Study in the Southeastern United States

NASA Astrophysics Data System (ADS)

Cheng, Y.; Niemeyer, R. J.; Zhang, X.; Yearsley, J. R.; Voisin, N.; Nijssen, B.

2017-12-01

Climate change and associated changes in air temperature and precipitation are projected to impact natural water resources quantity, quality and timing. In the past century, over 280 major dams were built in the Southeastern United States (SEUS) (GRanD database). Regulation of the river system greatly alters natural streamflow as well as stream temperature. Understanding the impacts of climate change on regulated systems, particularly within the context of the Clean Water Act, can inform stakeholders how to maintain and adapt water operations (e.g. regulation, withdrawals). In this study, we use a new modeling framework to study climate change impacts on stream temperatures of a regulated river system. We simulate runoff with the Variable Infiltration Capacity (VIC) macroscale hydrological model, regulated streamflow and reservoir operations with a large-scale river routing-reservoir model (MOSART-WM), and stream temperature using the River Basin Model (RBM). We enhanced RBM with a two-layer thermal stratification reservoir module. This modeling framework captures both the impact of reservoir regulation on streamflow and the reservoir stratification effects on downstream temperatures. We evaluate changes in flow and stream temperatures based on climate projections from two representative concentration pathways (RCPs; RCP4.5 and RCP8.5) from the Coupled Model Intercomparison Project Phase 5 (CMIP5). We simulate river temperature with meteorological forcings that have been downscaled with the Multivariate Constructed Analogs (MACA) method. We are specifically interested in analyzing extreme periods during which stream temperature exceeds water quality standards. In this study, we focus on identifying whether these extreme temperature periods coincide with low flows, and whether the frequency and duration of these operationally-relevant periods will increase under future climate change.

3D-printed soft-tissue physical models of renal malignancies for individualized surgical simulation: a feasibility study.

PubMed

Maddox, Michael M; Feibus, Allison; Liu, James; Wang, Julie; Thomas, Raju; Silberstein, Jonathan L

2018-03-01

To construct patient-specific physical three-dimensional (3D) models of renal units with materials that approximates the properties of renal tissue to allow pre-operative and robotic training surgical simulation, 3D physical kidney models were created (3DSystems, Rock Hill, SC) using computerized tomography to segment structures of interest (parenchyma, vasculature, collection system, and tumor). Images were converted to a 3D surface mesh file for fabrication using a multi-jet 3D printer. A novel construction technique was employed to approximate normal renal tissue texture, printers selectively deposited photopolymer material forming the outer shell of the kidney, and subsequently, an agarose gel solution was injected into the inner cavity recreating the spongier renal parenchyma. We constructed seven models of renal units with suspected malignancies. Partial nephrectomy and renorrhaphy were performed on each of the replicas. Subsequently all patients successfully underwent robotic partial nephrectomy. Average tumor diameter was 4.4 cm, warm ischemia time was 25 min, RENAL nephrometry score was 7.4, and surgical margins were negative. A comparison was made between the seven cases and the Tulane Urology prospectively maintained robotic partial nephrectomy database. Patients with surgical models had larger tumors, higher nephrometry score, longer warm ischemic time, fewer positive surgical margins, shorter hospitalization, and fewer post-operative complications; however, the only significant finding was lower estimated blood loss (186 cc vs 236; p = 0.01). In this feasibility study, pre-operative resectable physical 3D models can be constructed and used as patient-specific surgical simulation tools; further study will need to demonstrate if this results in improvement of surgical outcomes and robotic simulation education.

A Feasibility Study to Investigate the Structure and Operation of a Model Occupational Information Dissemination Unit Which Would Operate Between the New York State Employment Service and the New York State Education Department.

ERIC Educational Resources Information Center

Dubato, George S.

The possibility was explored of greater cooperation between the New York State Employment Service and the secondary schools and 2-year colleges of New York in the production and dissemination of improved occupational information for students and counselors. To compile data on present practices and opinions of counselors and administrators,…

Technology Assessment of Avanced propulsion Systems for Some Classes of Combat Vehicles. Volume 3. Appendices G-M.

DTIC Science & Technology

1978-09-01

generally recognized that the best possible configura- tion for engines operating at high speeds and at high-pressure levels is probably the single...engines is invariably accom- plished by the operation of computer simulation models that generate specific numerical data rather than the generalized re...lationships common to other forms of prime mover based on units of mass or volume. Thus, providing such generalized relation- ships for a Stirling

Enhancing the Effectiveness of Ad Hoc Units: A Revised Training Model

DTIC Science & Technology

2009-06-01

thank Dr. Kalev “Gunner” Sepp, Dr. Bob McNab, Dr. John Arquilla, Dr. Nancy Roberts, Dr. Susan Hocevar, and Dr. Dorothy Denning for providing their...also want to thank Colonel Paul Warren, Information Operations Branch Chief at U.S. Central Command – Special Operations (SOCCENT), for sponsoring my...Academy of Management Journal, 38 (1), 60-84. Paul M. Nemiroff, Paul M., William, A. Pasmore and David L. Ford, Jr., “The Effects of Two

Demonstration of a residential CHP system based on PEM fuel cells

NASA Astrophysics Data System (ADS)

Gigliucci, G.; Petruzzi, L.; Cerelli, E.; Garzisi, A.; La Mendola, A.

Fuel cell-based CHP systems are very attractive for stationary energy generation, since they allow production of electricity and heat in a decentralised, quiet, efficient and environmentally friendly way. As a means of evaluating this new technology, Enel Produzione installed a beta-version fuel cell CHP system, supplied by H-Power, at its experimental area sited in Livorno (Italy), and submitted it to a series of tests. The system is a co-generative unit, converting natural gas into electricity and heat: the former is delivered to local loads using electric load following capability; the latter is delivered to the experimental area hydraulic refrigeration circuit. Experiments were aimed at assessing the suitability of this kind of system to supply Italian residential customers. Factors such as performances, flexibility and operational requirements were evaluated under all the possible operating conditions, both under grid connected and stand alone configurations. At the same time, a mathematical model of the FC/CHP unit was developed to allow for the prediction of system performances and operating parameters under off-design conditions. This model can be used as an effective tool to optimise system operation when a particular customer has to be supplied. Results show that the prototype behaved as expected by a first "proof of concept" system and outline improvements to be achieved in order to satisfy the energy needs of small residential applications.

40 CFR 60.2989 - Does this subpart directly affect incineration unit owners and operators in my State?

Code of Federal Regulations, 2010 CFR

2010-07-01

... incineration unit owners and operators in my State? 60.2989 Section 60.2989 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Other Solid Waste Incineration Units That Commenced... incineration unit owners and operators in my State? (a) No, this subpart does not directly affect incineration...

Independent Auditors Report on the Air Force Working Capital Fund FY 2015 and FY 2014 Basic Financial Statements for United States Air Force Agency Financial Report 2015

DTIC Science & Technology

2015-11-09

missile warning, weather and intelligence warfighting support. AFSPC operates sensors that provide direct attack warning and assessment to U.S...toughness combinations. AFRL conducted low-speed wind tunnel tests of 9%-scale model completed at NASA Langley Research Center (LaRC); data validated... wireless mobile monitoring capability designed for dismounted Pararescue Jumpers (PJ) called United States Air Force 89 Battlefield Airmen Trauma

APPLYING LESSONS LEARNED FROM THE UNITED STATES SPECIAL OPERATIONS COMMAND’S HUMAN PERFORMANCE PROGRAM TO THE UNITED STATES AIR FORCES COMPREHENSIVE AIRMAN FITNESS

DTIC Science & Technology

2016-04-01

implementation, focusing physical training on the mission specific requirements of the individual similar to an athletic sports model, increasing access to...initiative as a mechanism to help maintain the resiliency, health, and welfare of its force.1 As Air Force Instruction (AFI) 90-506 states, the strategy ...implementation of Tactical Athlete Programs, which provide tailored workout plans and nutrition education that prepare service members to meet the physical

High Power Alternator Test Unit (ATU) Electrical System Test

NASA Technical Reports Server (NTRS)

Birchenough, Arthur; Hervol, David

2007-01-01

The Alternator Test Unit (ATU) in the Lunar Power System Facility (LPSF) located at the NASA Glenn Research Center (GRC) in Cleveland, OH was used to simulate the operating conditions and evaluate the performance of the ATU and it s interaction with various LPSF components in accordance with the JIMO AC Power System Requirements. The testing was carried out at the breadboard development level. Results of these tests will be used for the development and validation of analytical models for performance and lifetime prediction.

Effect of primary and secondary parameters on analytical estimation of effective thermal conductivity of two phase materials using unit cell approach

NASA Astrophysics Data System (ADS)

S, Chidambara Raja; P, Karthikeyan; Kumaraswamidhas, L. A.; M, Ramu

2018-05-01

Most of the thermal design systems involve two phase materials and analysis of such systems requires detailed understanding of the thermal characteristics of the two phase material. This article aimed to develop geometry dependent unit cell approach model by considering the effects of all primary parameters (conductivity ratio and concentration) and secondary parameters (geometry, contact resistance, natural convection, Knudsen and radiation) for the estimation of effective thermal conductivity of two-phase materials. The analytical equations have been formulated based on isotherm approach for 2-D and 3-D spatially periodic medium. The developed models are validated with standard models and suited for all kind of operating conditions. The results have shown substantial improvement compared to the existing models and are in good agreement with the experimental data.

Combined effect of noise and vibration on passenger acceptance

NASA Technical Reports Server (NTRS)

Leatherwood, J. D.

1984-01-01

An extensive research program conducted at NASA Langley Research Center to develop a comprehensive model of passenger comfort response to combined noise and vibration environments has been completed. This model was developed for use in the prediction and/or assessment of vehicle ride quality and as a ride quality design tool. The model has the unique capability to transform individual elements of vehicle interior noise and vibration into subjective units and combining the subjective units to produce a total subjective discomfort index as well as the other useful subjective indices. This paper summarizes the basic approach used in the development of the NASA ride comfort model, presents some of the more fundamental results obtained, describes several application of the model to operational vehicles, and discusses a portable, self-contained ride quality meter system that is a direct hardware/software implementation of the NASA comfort algorithm.

Use of mock-up training to reduce personnel exposure at the North Anna Unit 1 Steam Generator Replacement Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henry, H.G.; Reilly, B.P.

1995-03-01

The North Anna Power Station is located on the southern shore of Lake Anna in Louisa County, approximately forty miles northwest of Richmond, Virginia. The two 910 Mw nuclear units located on this site are owned by Virginia Electric and Power Company (Virginia Power) and Old Dominion Electric Cooperative and operated by Virginia Power. Fuel was loaded into Unit 1 in December 1977, and it began commercial operation in June 1978. Fuel was loaded into Unit 2 in April 1980 and began commercial operation in December 1980. Each nuclear unit includes a three-coolant-loop pressurized light water reactor nuclear steam supplymore » system that was furnished by Westinghouse Electric Corporation. Included within each system were three Westinghouse Model 51 steam generators with alloy 600, mill-annealed tubing material. Over the years of operation of Unit 1, various corrosion-related phenomena had occurred that affected the steam generators tubing and degraded their ability to fulfill their heat transfer function. Advanced inspection and repair techniques helped extend the useful life of the steam generators, but projections based on the results of the inspections indicated that the existing steam generators tubing and degraded their ability to fullfill their heat transfer function. Advanced inspection and repair techniques helped extend the useful life of the steam generators, but projections based on the results of the inspections indicated that the existing steam generators would not last their design life and must be repaired. To this end Virginia Power determined that a steam generator replacement (SGR) program was necessary to remove the old steam generator tube bundles and lower shell sections, including the channel heads (collectively called the lower assemblies), and replace them with new lower assemblies incorporating design features that will prevent the degradation problems that the old steam generators had experienced.« less

Acute Surgical Unit: a new model of care.

PubMed

Cox, Michael R; Cook, Lyn; Dobson, Jennifer; Lambrakis, Paul; Ganesh, Shanthan; Cregan, Patrick

2010-06-01

The traditional on-call system for the management of acute general surgical admissions is inefficient and outdated. A new model, Acute Surgical Unit (ASU), was developed at Nepean Hospital in 2006. The ASU is a consultant-driven, independent unit that manages all acute general surgical admissions. The team has the same make up 7 days a week and functions the same every day, including weekends and public holidays. The consultant does a 24-h period of on-call, from 7 pm to 7 pm. They are on remote call from 7 pm to 7 am and are in the hospital from 7 am to 7 pm with their sole responsibility being to the ASU. The ASU has a day team with two registrars, two residents and a nurse practitioner. All patients are admitted and stay in the ASU until discharge or transfer to other units. Handover of the patients at the end of each day is facilitated by a comprehensive ASU database. The implementation of the ASU at Nepean Hospital has improved the timing of assessment by the surgical unit. There has been significant improvement in the timing of operative management, with an increased number and proportion of cases being done during daylight hours, with an associated reduction in the proportion of cases performed afterhours. There is greater trainee supervision with regard to patient assessment, management and operative procedures. There has been an improvement in the consultants' work conditions. The ASU provides an excellent training opportunity for surgical trainees, residents and interns in the assessment and management of acute surgical conditions.

Three-dimensional computer-aided human factors engineering analysis of a grafting robot.

PubMed

Chiu, Y C; Chen, S; Wu, G J; Lin, Y H

2012-07-01

The objective of this research was to conduct a human factors engineering analysis of a grafting robot design using computer-aided 3D simulation technology. A prototype tubing-type grafting robot for fruits and vegetables was the subject of a series of case studies. To facilitate the incorporation of human models into the operating environment of the grafting robot, I-DEAS graphic software was applied to establish individual models of the grafting robot in line with Jack ergonomic analysis. Six human models (95th percentile, 50th percentile, and 5th percentile by height for both males and females) were employed to simulate the operating conditions and working postures in a real operating environment. The lower back and upper limb stresses of the operators were analyzed using the lower back analysis (LBA) and rapid upper limb assessment (RULA) functions in Jack. The experimental results showed that if a leg space is introduced under the robot, the operator can sit closer to the robot, which reduces the operator's level of lower back and upper limbs stress. The proper environmental layout for Taiwanese operators for minimum levels of lower back and upper limb stress are to set the grafting operation at 23.2 cm away from the operator at a height of 85 cm and with 45 cm between the rootstock and scion units.

Connectionist models of conditioning: A tutorial

PubMed Central

Kehoe, E. James

1989-01-01

Models containing networks of neuron-like units have become increasingly prominent in the study of both cognitive psychology and artificial intelligence. This article describes the basic features of connectionist models and provides an illustrative application to compound-stimulus effects in respondent conditioning. Connectionist models designed specifically for operant conditioning are not yet widely available, but some current learning algorithms for machine learning indicate that such models are feasible. Conversely, designers for machine learning appear to have recognized the value of behavioral principles in producing adaptive behavior in their creations. PMID:16812604

Philipp Beiter | NREL

Science.gov Websites

the Strategic Energy Analysis Center. Areas of Expertise Cost modeling and economic analysis of , 2011 Prior Work Experience Junior Policy Analyst, Organization for Economic Co-operation and . Smith. 2017. An Assessment of the Economic Potential of Offshore Wind in the United States from 2015 to

40 CFR 60.5230 - What records must I keep?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Existing Sewage Sludge Incineration Units Model Rule-Recordkeeping and Reporting § 60.5230 What records... standards under this subpart. (ii) Procedures for receiving, handling, and feeding sewage sludge. (iii... performance test, if in addition to sewage sludge. (x) For each qualified operator and other plant personnel...

40 CFR 60.5230 - What records must I keep?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Existing Sewage Sludge Incineration Units Model Rule-Recordkeeping and Reporting § 60.5230 What records... standards under this subpart. (ii) Procedures for receiving, handling, and feeding sewage sludge. (iii... performance test, if in addition to sewage sludge. (x) For each qualified operator and other plant personnel...

40 CFR 60.5230 - What records must I keep?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Existing Sewage Sludge Incineration Units Model Rule-Recordkeeping and Reporting § 60.5230 What records... standards under this subpart. (ii) Procedures for receiving, handling, and feeding sewage sludge. (iii... performance test, if in addition to sewage sludge. (x) For each qualified operator and other plant personnel...

40 CFR 60.5230 - What records must I keep?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Existing Sewage Sludge Incineration Units Model Rule-Recordkeeping and Reporting § 60.5230 What records... standards under this subpart. (ii) Procedures for receiving, handling, and feeding sewage sludge. (iii... performance test, if in addition to sewage sludge. (x) For each qualified operator and other plant personnel...

Approaches to Resource Allocation

ERIC Educational Resources Information Center

Dressel, Paul; Simon, Lou Anna Kimsey

1976-01-01

Various budgeting patterns and strategies are currently in use, each with its own particular strengths and weaknesses. Neither cost-benefit analysis nor cost-effectiveness analysis offers any better solution to the allocation problem than do the unsupported contentions of departments or the historical unit costs. An operable model that performs…

78 FR 44043 - Airworthiness Directives; Eurocopter France Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-23

...-0635; Directorate Identifier 2012-SW-081-AD] RIN 2120-AA64 Airworthiness Directives; Eurocopter France...). SUMMARY: We propose to adopt a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model... France and are approved for operation in the United States. Pursuant to our bilateral agreement with...

77 FR 44509 - Airworthiness Directives; Eurocopter France Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-30

...-0795; Directorate Identifier 2008-SW-53-AD] RIN 2120-AA64 Airworthiness Directives; Eurocopter France...). SUMMARY: We propose to adopt a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model... by the aviation authority of the France and are approved for operation in the United States. Pursuant...

78 FR 33764 - Airworthiness Directives; Eurocopter France Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-05

...-0479; Directorate Identifier 2011-SW-070-AD] RIN 2120-AA64 Airworthiness Directives; Eurocopter France...). SUMMARY: We propose to adopt a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model... authority of France and are approved for operation in the United States. Pursuant to our bilateral agreement...

43 CFR 3186.1 - Model onshore unit agreement for unproven areas.

Code of Federal Regulations, 2013 CFR

2013-10-01

... effect as of the effective date hereof governing drilling and producing operations, not inconsistent with..., and other production or development purposes, or for repressuring or recycling in accordance with a... from one participating area is used for repressuring or recycling purposes in another participating...

43 CFR 3186.1 - Model onshore unit agreement for unproven areas.

Code of Federal Regulations, 2012 CFR

2012-10-01

... effect as of the effective date hereof governing drilling and producing operations, not inconsistent with..., and other production or development purposes, or for repressuring or recycling in accordance with a... from one participating area is used for repressuring or recycling purposes in another participating...

43 CFR 3186.1 - Model onshore unit agreement for unproven areas.

Code of Federal Regulations, 2011 CFR

2011-10-01

... effect as of the effective date hereof governing drilling and producing operations, not inconsistent with..., and other production or development purposes, or for repressuring or recycling in accordance with a... from one participating area is used for repressuring or recycling purposes in another participating...

43 CFR 3186.1 - Model onshore unit agreement for unproven areas.

Code of Federal Regulations, 2014 CFR

2014-10-01

... effect as of the effective date hereof governing drilling and producing operations, not inconsistent with..., and other production or development purposes, or for repressuring or recycling in accordance with a... from one participating area is used for repressuring or recycling purposes in another participating...

Modeling stream temperature in the Anthropocene: An earth system modeling approach

DOE PAGES

Li, Hong -Yi; Leung, L. Ruby; Tesfa, Teklu; ...

2015-10-29

A new large-scale stream temperature model has been developed within the Community Earth System Model (CESM) framework. The model is coupled with the Model for Scale Adaptive River Transport (MOSART) that represents river routing and a water management model (WM) that represents the effects of reservoir operations and water withdrawals on flow regulation. The coupled models allow the impacts of reservoir operations and withdrawals on stream temperature to be explicitly represented in a physically based and consistent way. The models have been applied to the Contiguous United States driven by observed meteorological forcing. It is shown that the model ismore » capable of reproducing stream temperature spatiotemporal variation satisfactorily by comparison against the observed streamflow from over 320 USGS stations. Including water management in the models improves the agreement between the simulated and observed streamflow at a large number of stream gauge stations. Both climate and water management are found to have important influence on the spatiotemporal patterns of stream temperature. More interestingly, it is quantitatively estimated that reservoir operation could cool down stream temperature in the summer low-flow season (August – October) by as much as 1~2oC over many places, as water management generally mitigates low flow, which has important implications to aquatic ecosystems. In conclusion, sensitivity of the simulated stream temperature to input data and reservoir operation rules used in the WM model motivates future directions to address some limitations in the current modeling framework.« less

GUIDING PRINCIPLES FOR GOOD PRACTICES IN HOSPITAL-BASED HEALTH TECHNOLOGY ASSESSMENT UNITS.

PubMed

Sampietro-Colom, Laura; Lach, Krzysztof; Pasternack, Iris; Wasserfallen, Jean-Blaise; Cicchetti, Americo; Marchetti, Marco; Kidholm, Kristian; Arentz-Hansen, Helene; Rosenmöller, Magdalene; Wild, Claudia; Kahveci, Rabia; Ulst, Margus

2015-01-01

Health technology assessment (HTA) carried out for policy decision making has well-established principles unlike hospital-based HTA (HB-HTA), which differs from the former in the context characteristics and ways of operation. This study proposes principles for good practices in HB-HTA units. A framework for good practice criteria was built inspired by the EFQM excellence business model and information from six literature reviews, 107 face-to-face interviews, forty case studies, large-scale survey, focus group, Delphi survey, as well as local and international validation. In total, 385 people from twenty countries have participated in defining the principles for good practices in HB-HTA units. Fifteen guiding principles for good practices in HB-HTA units are grouped in four dimensions. Dimension 1 deals with principles of the assessment process aimed at providing contextualized information for hospital decision makers. Dimension 2 describes leadership, strategy and partnerships of HB-HTA units which govern and facilitate the assessment process. Dimension 3 focuses on adequate resources that ensure the operation of HB-HTA units. Dimension 4 deals with measuring the short- and long-term impact of the overall performance of HB-HTA units. Finally, nine core guiding principles were selected as essential requirements for HB-HTA units based on the expertise of the HB-HTA units participating in the project. Guiding principles for good practices set up a benchmark for HB-HTA because they represent the ideal performance of HB-HTA units; nevertheless, when performing HTA at hospital level, context also matters; therefore, they should be adapted to ensure their applicability in the local context.

Bulk energy storage increases United States electricity system emissions.

PubMed

Hittinger, Eric S; Azevedo, Inês M L

2015-03-03

Bulk energy storage is generally considered an important contributor for the transition toward a more flexible and sustainable electricity system. Although economically valuable, storage is not fundamentally a "green" technology, leading to reductions in emissions. We model the economic and emissions effects of bulk energy storage providing an energy arbitrage service. We calculate the profits under two scenarios (perfect and imperfect information about future electricity prices), and estimate the effect of bulk storage on net emissions of CO2, SO2, and NOx for 20 eGRID subregions in the United States. We find that net system CO2 emissions resulting from storage operation are nontrivial when compared to the emissions from electricity generation, ranging from 104 to 407 kg/MWh of delivered energy depending on location, storage operation mode, and assumptions regarding carbon intensity. Net NOx emissions range from -0.16 (i.e., producing net savings) to 0.49 kg/MWh, and are generally small when compared to average generation-related emissions. Net SO2 emissions from storage operation range from -0.01 to 1.7 kg/MWh, depending on location and storage operation mode.

An artificial neural network model for periodic trajectory generation

NASA Astrophysics Data System (ADS)

Shankar, S.; Gander, R. E.; Wood, H. C.

A neural network model based on biological systems was developed for potential robotic application. The model consists of three interconnected layers of artificial neurons or units: an input layer subdivided into state and plan units, an output layer, and a hidden layer between the two outer layers which serves to implement nonlinear mappings between the input and output activation vectors. Weighted connections are created between the three layers, and learning is effected by modifying these weights. Feedback connections between the output and the input state serve to make the network operate as a finite state machine. The activation vector of the plan units of the input layer emulates the supraspinal commands in biological central pattern generators in that different plan activation vectors correspond to different sequences or trajectories being recalled, even with different frequencies. Three trajectories were chosen for implementation, and learning was accomplished in 10,000 trials. The fault tolerant behavior, adaptiveness, and phase maintenance of the implemented network are discussed.

Tools for Evaluating Fault Detection and Diagnostic Methods for HVAC Secondary Systems

NASA Astrophysics Data System (ADS)

Pourarian, Shokouh

Although modern buildings are using increasingly sophisticated energy management and control systems that have tremendous control and monitoring capabilities, building systems routinely fail to perform as designed. More advanced building control, operation, and automated fault detection and diagnosis (AFDD) technologies are needed to achieve the goal of net-zero energy commercial buildings. Much effort has been devoted to develop such technologies for primary heating ventilating and air conditioning (HVAC) systems, and some secondary systems. However, secondary systems, such as fan coil units and dual duct systems, although widely used in commercial, industrial, and multifamily residential buildings, have received very little attention. This research study aims at developing tools that could provide simulation capabilities to develop and evaluate advanced control, operation, and AFDD technologies for these less studied secondary systems. In this study, HVACSIM+ is selected as the simulation environment. Besides developing dynamic models for the above-mentioned secondary systems, two other issues related to the HVACSIM+ environment are also investigated. One issue is the nonlinear equation solver used in HVACSIM+ (Powell's Hybrid method in subroutine SNSQ). It has been found from several previous research projects (ASRHAE RP 825 and 1312) that SNSQ is especially unstable at the beginning of a simulation and sometimes unable to converge to a solution. Another issue is related to the zone model in the HVACSIM+ library of components. Dynamic simulation of secondary HVAC systems unavoidably requires an interacting zone model which is systematically and dynamically interacting with building surrounding. Therefore, the accuracy and reliability of the building zone model affects operational data generated by the developed dynamic tool to predict HVAC secondary systems function. The available model does not simulate the impact of direct solar radiation that enters a zone through glazing and the study of zone model is conducted in this direction to modify the existing zone model. In this research project, the following tasks are completed and summarized in this report: 1. Develop dynamic simulation models in the HVACSIM+ environment for common fan coil unit and dual duct system configurations. The developed simulation models are able to produce both fault-free and faulty operational data under a wide variety of faults and severity levels for advanced control, operation, and AFDD technology development and evaluation purposes; 2. Develop a model structure, which includes the grouping of blocks and superblocks, treatment of state variables, initial and boundary conditions, and selection of equation solver, that can simulate a dual duct system efficiently with satisfactory stability; 3. Design and conduct a comprehensive and systematic validation procedure using collected experimental data to validate the developed simulation models under both fault-free and faulty operational conditions; 4. Conduct a numerical study to compare two solution techniques: Powell's Hybrid (PH) and Levenberg-Marquardt (LM) in terms of their robustness and accuracy. 5. Modification of the thermal state of the existing building zone model in HVACSIM+ library of component. This component is revised to consider the transmitted heat through glazing as a heat source for transient building zone load prediction In this report, literature, including existing HVAC dynamic modeling environment and models, HVAC model validation methodologies, and fault modeling and validation methodologies, are reviewed. The overall methodologies used for fault free and fault model development and validation are introduced. Detailed model development and validation results for the two secondary systems, i.e., fan coil unit and dual duct system are summarized. Experimental data mostly from the Iowa Energy Center Energy Resource Station are used to validate the models developed in this project. Satisfactory model performance in both fault free and fault simulation studies is observed for all studied systems.

Cortical circuitry implementing graphical models.

PubMed

Litvak, Shai; Ullman, Shimon

2009-11-01

In this letter, we develop and simulate a large-scale network of spiking neurons that approximates the inference computations performed by graphical models. Unlike previous related schemes, which used sum and product operations in either the log or linear domains, the current model uses an inference scheme based on the sum and maximization operations in the log domain. Simulations show that using these operations, a large-scale circuit, which combines populations of spiking neurons as basic building blocks, is capable of finding close approximations to the full mathematical computations performed by graphical models within a few hundred milliseconds. The circuit is general in the sense that it can be wired for any graph structure, it supports multistate variables, and it uses standard leaky integrate-and-fire neuronal units. Following previous work, which proposed relations between graphical models and the large-scale cortical anatomy, we focus on the cortical microcircuitry and propose how anatomical and physiological aspects of the local circuitry may map onto elements of the graphical model implementation. We discuss in particular the roles of three major types of inhibitory neurons (small fast-spiking basket cells, large layer 2/3 basket cells, and double-bouquet neurons), subpopulations of strongly interconnected neurons with their unique connectivity patterns in different cortical layers, and the possible role of minicolumns in the realization of the population-based maximum operation.

A case study examination of structure and function in a state health department chronic disease unit.

PubMed

Alongi, Jeanne

2015-04-01

I explored the structural and operational practices of the chronic disease prevention and control unit of a state health department and proposed a conceptual model of structure, function, and effectiveness for future study. My exploratory case study examined 7 elements of organizational structure and practice. My interviews with staff and external stakeholders of a single chronic disease unit yielded quantitative and qualitative data that I coded by perspective, process, relationship, and activity. I analyzed these for patterns and emerging themes. Chi-square analysis revealed significant correlations among collaboration with goal ambiguity, political support, and responsiveness, and evidence-based decisions with goal ambiguity and responsiveness. Although my study design did not permit conclusions about causality, my findings suggested that some elements of the model might facilitate effectiveness for chronic disease units and should be studied further. My findings might have important implications for identifying levers around which capacity can be built that may strengthen effectiveness.

A Case Study Examination of Structure and Function in a State Health Department Chronic Disease Unit

PubMed Central

2015-01-01

Objectives. I explored the structural and operational practices of the chronic disease prevention and control unit of a state health department and proposed a conceptual model of structure, function, and effectiveness for future study. Methods. My exploratory case study examined 7 elements of organizational structure and practice. My interviews with staff and external stakeholders of a single chronic disease unit yielded quantitative and qualitative data that I coded by perspective, process, relationship, and activity. I analyzed these for patterns and emerging themes. Results. Chi-square analysis revealed significant correlations among collaboration with goal ambiguity, political support, and responsiveness, and evidence-based decisions with goal ambiguity and responsiveness. Conclusions. Although my study design did not permit conclusions about causality, my findings suggested that some elements of the model might facilitate effectiveness for chronic disease units and should be studied further. My findings might have important implications for identifying levers around which capacity can be built that may strengthen effectiveness. PMID:25689211

Divergent projections of future land use in the United States arising from different models and scenarios

USGS Publications Warehouse

Sohl, Terry L.; Wimberly, Michael; Radeloff, Volker C.; Theobald, David M.; Sleeter, Benjamin M.

2016-01-01

A variety of land-use and land-cover (LULC) models operating at scales from local to global have been developed in recent years, including a number of models that provide spatially explicit, multi-class LULC projections for the conterminous United States. This diversity of modeling approaches raises the question: how consistent are their projections of future land use? We compared projections from six LULC modeling applications for the United States and assessed quantitative, spatial, and conceptual inconsistencies. Each set of projections provided multiple scenarios covering a period from roughly 2000 to 2050. Given the unique spatial, thematic, and temporal characteristics of each set of projections, individual projections were aggregated to a common set of basic, generalized LULC classes (i.e., cropland, pasture, forest, range, and urban) and summarized at the county level across the conterminous United States. We found very little agreement in projected future LULC trends and patterns among the different models. Variability among scenarios for a given model was generally lower than variability among different models, in terms of both trends in the amounts of basic LULC classes and their projected spatial patterns. Even when different models assessed the same purported scenario, model projections varied substantially. Projections of agricultural trends were often far above the maximum historical amounts, raising concerns about the realism of the projections. Comparisons among models were hindered by major discrepancies in categorical definitions, and suggest a need for standardization of historical LULC data sources. To capture a broader range of uncertainties, ensemble modeling approaches are also recommended. However, the vast inconsistencies among LULC models raise questions about the theoretical and conceptual underpinnings of current modeling approaches. Given the substantial effects that land-use change can have on ecological and societal processes, there is a need for improvement in LULC theory and modeling capabilities to improve acceptance and use of regional- to national-scale LULC projections for the United States and elsewhere.

Comparative study of the Aristotle Comprehensive Complexity and the Risk Adjustment in Congenital Heart Surgery scores.

PubMed

Bojan, Mirela; Gerelli, Sébastien; Gioanni, Simone; Pouard, Philippe; Vouhé, Pascal

2011-09-01

The Aristotle Comprehensive Complexity (ACC) and the Risk Adjustment in Congenital Heart Surgery (RACHS-1) scores have been proposed for complexity adjustment in the analysis of outcome after congenital heart surgery. Previous studies found RACHS-1 to be a better predictor of outcome than the Aristotle Basic Complexity score. We compared the ability to predict operative mortality and morbidity between ACC, the latest update of the Aristotle method and RACHS-1. Morbidity was assessed by length of intensive care unit stay. We retrospectively enrolled patients undergoing congenital heart surgery. We modeled each score as a continuous variable, mortality as a binary variable, and length of stay as a censored variable. We compared performance between mortality and morbidity models using likelihood ratio tests for nested models and paired concordance statistics. Among all 1,384 patients enrolled, 30-day mortality rate was 3.5% and median length of intensive care unit stay was 3 days. Both scores strongly related to mortality, but ACC made better prediction than RACHS-1; c-indexes 0.87 (0.84, 0.91) vs 0.75 (0.65, 0.82). Both scores related to overall length of stay only during the first postoperative week, but ACC made better predictions than RACHS-1; U statistic=0.22, p<0.001. No significant difference was noted after adjusting RACHS-1 models on age, prematurity, and major extracardiac abnormalities. The ACC was a better predictor of operative mortality and length of intensive care unit stay than RACHS-1. In order to achieve similar performance, regression models including RACHS-1 need to be further adjusted on age, prematurity, and major extracardiac abnormalities. Copyright © 2011 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Prediction of Francis Turbine Prototype Part Load Pressure and Output Power Fluctuations with Hydroelectric Model

NASA Astrophysics Data System (ADS)

Alligné, S.; Nicolet, C.; Béguin, A.; Landry, C.; Gomes, J.; Avellan, F.

2017-04-01

The prediction of pressure and output power fluctuations amplitudes on Francis turbine prototype is a challenge for hydro-equipment industry since it is subjected to guarantees to ensure smooth and reliable operation of the hydro units. The European FP7 research project Hyperbole aims to setup a methodology to transpose the pressure fluctuations induced by the cavitation vortex rope from the reduced scale model to the prototype generating units. A Francis turbine unit of 444MW with a specific speed value of ν = 0.29, is considered as case study. A SIMSEN model of the power station including electrical system, controllers, rotating train and hydraulic system with transposed draft tube excitation sources is setup. Based on this model, a frequency analysis of the hydroelectric system is performed for all technologies to analyse potential interactions between hydraulic excitation sources and electrical components. Three technologies have been compared: the classical fixed speed configuration with Synchronous Machine (SM) and the two variable speed technologies which are Doubly Fed Induction Machine (DFIM) and Full Size Frequency Converter (FSFC).

System-wide emissions implications of increased wind power penetration.

PubMed

Valentino, Lauren; Valenzuela, Viviana; Botterud, Audun; Zhou, Zhi; Conzelmann, Guenter

2012-04-03

This paper discusses the environmental effects of incorporating wind energy into the electric power system. We present a detailed emissions analysis based on comprehensive modeling of power system operations with unit commitment and economic dispatch for different wind penetration levels. First, by minimizing cost, the unit commitment model decides which thermal power plants will be utilized based on a wind power forecast, and then, the economic dispatch model dictates the level of production for each unit as a function of the realized wind power generation. Finally, knowing the power production from each power plant, the emissions are calculated. The emissions model incorporates the effects of both cycling and start-ups of thermal power plants in analyzing emissions from an electric power system with increasing levels of wind power. Our results for the power system in the state of Illinois show significant emissions effects from increased cycling and particularly start-ups of thermal power plants. However, we conclude that as the wind power penetration increases, pollutant emissions decrease overall due to the replacement of fossil fuels.

Modeling and control of distributed energy systems during transition between grid connected and standalone modes

NASA Astrophysics Data System (ADS)

Arafat, Md Nayeem

Distributed generation systems (DGs) have been penetrating into our energy networks with the advancement in the renewable energy sources and energy storage elements. These systems can operate in synchronism with the utility grid referred to as the grid connected (GC) mode of operation, or work independently, referred to as the standalone (SA) mode of operation. There is a need to ensure continuous power flow during transition between GC and SA modes, referred to as the transition mode, in operating DGs. In this dissertation, efficient and effective transition control algorithms are developed for DGs operating either independently or collectively with other units. Three techniques are proposed in this dissertation to manage the proper transition operations. In the first technique, a new control algorithm is proposed for an independent DG which can operate in SA and GC modes. The proposed transition control algorithm ensures low total harmonic distortion (THD) and less voltage fluctuation during mode transitions compared to the other techniques. In the second technique, a transition control is suggested for a collective of DGs operating in a microgrid system architecture to improve the reliability of the system, reduce the cost, and provide better performance. In this technique, one of the DGs in a microgrid system, referred to as a dispatch unit , takes the additional responsibility of mode transitioning to ensure smooth transition and supply/demand balance in the microgrid. In the third technique, an alternative transition technique is proposed through hybridizing the current and droop controllers. The proposed hybrid transition control technique has higher reliability compared to the dispatch unit concept. During the GC mode, the proposed hybrid controller uses current control. During the SA mode, the hybrid controller uses droop control. During the transition mode, both of the controllers participate in formulating the inverter output voltage but with different weights or coefficients. Voltage source inverters interfacing the DGs as well as the proposed transition control algorithms have been modeled to analyze the stability of the algorithms in different configurations. The performances of the proposed algorithms are verified through simulation and experimental studies. It has been found that the proposed control techniques can provide smooth power flow to the local loads during the GC, SA and transition modes.

Maintaining radiation exposures as low as reasonably achievable (ALARA) for dental personnel operating portable hand-held x-ray equipment.

PubMed

McGiff, Thomas J; Danforth, Robert A; Herschaft, Edward E

2012-08-01

Clinical experience indicates that newly available portable hand-held x-ray units provide advantages compared to traditional fixed properly installed and operated x-ray units in dental radiography. However, concern that hand-held x-ray units produce higher operator doses than fixed x-ray units has caused regulatory agencies to mandate requirements for use of hand-held units that go beyond those recommended by the manufacturer and can discourage the use of this technology. To assess the need for additional requirements, a hand-held x-ray unit and a pair of manikins were used to measure the dose to a simulated operator under two conditions: exposures made according to the manufacturer's recommendations and exposures made according to manufacturer's recommendation except for the removal of the x-ray unit's protective backscatter shield. Dose to the simulated operator was determined using an array of personal dosimeters and a pair of pressurized ion chambers. The results indicate that the dose to an operator of this equipment will be less than 0.6 mSv y⁻¹ if the device is used according to the manufacturer's recommendations. This suggests that doses to properly trained operators of well-designed, hand-held dental x-ray units will be below 1.0 mSv y⁻¹ (2% of the annual occupational dose limit) even if additional no additional operational requirements are established by regulatory agencies. This level of annual dose is similar to those reported as typical dental personnel using fixed x-ray units and appears to satisfy the ALARA principal for this class of occupational exposures.

Distributed photovoltaic system impact upon utility load/supply management practices

NASA Astrophysics Data System (ADS)

Vachtsevanos, G. J.; Meliopoulos, A. P.; Paraskevopoulos, B. K.

A methodology is described for simulation of the economic and technical factors of photovoltaic (PV) installations interfacing with utility load/management operations. A probabalistic technique is used to model the expected demand, reliability of the generating units, costs and profits from each unit, expected unserviced energy, and the loss of load probability. The available power from PV arrays is treated stochastically with statistical weighting on the basis of site meteorological data. The goal is to include the PV power while minimizing operational costs, taking into account the level of penetration of the total PV output. Two sample simulations for a utility with a diverse generating mix demonstrate that overall costs would decrease in both cases with PVs on-line through the emphasis on cheaper-fueled generators and peak-load shaving when possible.

The Advanced Technology Microwave Sounder (ATMS): A New Operational Sensor Series

NASA Technical Reports Server (NTRS)

Kim, Edward; Lyu, Cheng-H Joseph; Leslie, R. Vince; Baker, Neal; Mo, Tsan; Sun, Ninghai; Bi, Li; Anderson, Mike; Landrum, Mike; DeAmici, Giovanni;

Parametric Thermal Models of the Transient Reactor Test Facility (TREAT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley K. Heath

2014-03-01

This work supports the restart of transient testing in the United States using the Department of Energy’s Transient Reactor Test Facility at the Idaho National Laboratory. It also supports the Global Threat Reduction Initiative by reducing proliferation risk of high enriched uranium fuel. The work involves the creation of a nuclear fuel assembly model using the fuel performance code known as BISON. The model simulates the thermal behavior of a nuclear fuel assembly during steady state and transient operational modes. Additional models of the same geometry but differing material properties are created to perform parametric studies. The results show thatmore » fuel and cladding thermal conductivity have the greatest effect on fuel temperature under the steady state operational mode. Fuel density and fuel specific heat have the greatest effect for transient operational model. When considering a new fuel type it is recommended to use materials that decrease the specific heat of the fuel and the thermal conductivity of the fuel’s cladding in order to deal with higher density fuels that accompany the LEU conversion process. Data on the latest operating conditions of TREAT need to be attained in order to validate BISON’s results. BISON’s models for TREAT (material models, boundary convection models) are modest and need additional work to ensure accuracy and confidence in results.« less

Annual Summary Report Calendar Year 2000 for the 100-HR-3, 100-KR-4, and 100-NR-2 Operable Units and Pump-and-Treat Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

G. B. Mitchem

2001-08-22

This annual progress and performance evaluation report discusses the groundwater remedial actions in the 100 Area, including the interim actions at the 100-HR-3 and 100-KR-4 Operable Units, and also discusses the expedited response action in the 100-NR-2 operable unit.

Reactor engineering support of operations at the Davis-Besse nuclear power station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelley, D.B.

1995-12-31

Reactor engineering functions differ greatly from unit to unit; however, direct support of the reactor operators during reactor startups and operational transients is common to all units. This paper summarizes the support the reactor engineers provide the reactor operators during reactor startups and power changes through the use of automated computer programs at the Davis-Besse nuclear power station.

40 CFR 63.1281 - Control equipment requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for sources except small glycol dehydration units. Owners and operators of small glycol dehydration units shall comply with the control requirements in paragraph (f) of this section. (1) The control... or operator shall determine glycol dehydration unit baseline operations (as defined in § 63.1271...

40 CFR 63.1281 - Control equipment requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for sources except small glycol dehydration units. Owners and operators of small glycol dehydration units shall comply with the control requirements in paragraph (f) of this section. (1) The control... or operator shall determine glycol dehydration unit baseline operations (as defined in § 63.1271...

Incorporating Wind Power Forecast Uncertainties Into Stochastic Unit Commitment Using Neural Network-Based Prediction Intervals.

PubMed

Quan, Hao; Srinivasan, Dipti; Khosravi, Abbas

2015-09-01

Penetration of renewable energy resources, such as wind and solar power, into power systems significantly increases the uncertainties on system operation, stability, and reliability in smart grids. In this paper, the nonparametric neural network-based prediction intervals (PIs) are implemented for forecast uncertainty quantification. Instead of a single level PI, wind power forecast uncertainties are represented in a list of PIs. These PIs are then decomposed into quantiles of wind power. A new scenario generation method is proposed to handle wind power forecast uncertainties. For each hour, an empirical cumulative distribution function (ECDF) is fitted to these quantile points. The Monte Carlo simulation method is used to generate scenarios from the ECDF. Then the wind power scenarios are incorporated into a stochastic security-constrained unit commitment (SCUC) model. The heuristic genetic algorithm is utilized to solve the stochastic SCUC problem. Five deterministic and four stochastic case studies incorporated with interval forecasts of wind power are implemented. The results of these cases are presented and discussed together. Generation costs, and the scheduled and real-time economic dispatch reserves of different unit commitment strategies are compared. The experimental results show that the stochastic model is more robust than deterministic ones and, thus, decreases the risk in system operations of smart grids.