19. VIEW OF CRUDE ORE BINS FROM EAST. EAST CRUDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. VIEW OF CRUDE ORE BINS FROM EAST. EAST CRUDE ORE BIN IN FOREGROUND WITH DISCHARGE TO GRIZZLY AT BOTTOM OF VIEW. CONCRETE RETAINING WALL TO LEFT (SOUTH) AND BOTTOM (EAST EDGE OF EAST BIN). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

44. VIEW OF SOUTHWEST CORNER OF DRYER ROOM. DRYER FOUNDATION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. VIEW OF SOUTHWEST CORNER OF DRYER ROOM. DRYER FOUNDATION AT BOTTOM OF VIEW, WITH 18 INCH REVERSIBLE BELT CONVEYOR (UPPER LEFT), AND 16 INCH BELT CONVEYOR FINES FEED TO CRUSHED OXIDIZED ORE BIN (CENTER TO UPPER RIGHT). DRYER EXHAUST IS BELOW FINES FEED BELT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES. THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH THE MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-42 (CT) FOR IDENTICAL COLOR TRANSPARENCY - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-9 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

5. Foreground: ore bridges, ore/coke/limestone bins, Detroit River; background: stock ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Foreground: ore bridges, ore/coke/limestone bins, Detroit River; background: stock house on left, stripper building, BOF. Looking south/southwest - Rouge Steel Company, 3001 Miller Road, Dearborn, MI

25. DETAIL OF STRUCTURAL TIMBERS, ORE BIN, AND STAIRWAY TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. DETAIL OF STRUCTURAL TIMBERS, ORE BIN, AND STAIRWAY TO TOP FLOOR OF MILL, LOOKING SOUTH FROM SECOND FLOOR OF MILL. PORTION OF ORE BIN ON RIGHT, STAIRS ON LEFT. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT CRUSHED OXIDIZED ORE BIN FEED LEVEL. THE ROASTER IS BEYOND AND THE MACHINE SHOP IS ON THE TRAM TERRACE, UPPER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

64. NORTH WALL OF CRUSHED OXIDIZED ORE BIN. THE PRIMARY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

64. NORTH WALL OF CRUSHED OXIDIZED ORE BIN. THE PRIMARY MILL FEEDS AT BOTTOM. MILL SOLUTION TANKS WERE TO THE LEFT (EAST) AND BARREN SOLUTION TANK TO THE RIGHT (WEST) OR THE CRUSHED ORE BIN. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

SOUTH ELEVATION OF GOLD HILL MILL, LOOKING NORTH. THE PRIMARY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTH ELEVATION OF GOLD HILL MILL, LOOKING NORTH. THE PRIMARY ORE BIN IS A CENTER, WITH A JAW CRUSHER JUST TO THE RIGHT. A CONVEYOR (MISSING) WAS USED TO CARRY CRUSHED ORE UP AND INTO THE SECONDARY ORE BIN. THE STONE RAMP TO THE LEFT OF THE ORE BIN WAS USED TO DRIVE TRUCKS UP TO DUMPING LEVEL. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

DETAIL VIEW OF UPPER TRAM TERMINAL STRUCTURE, LOOKING NORTHEAST TOWARD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF UPPER TRAM TERMINAL STRUCTURE, LOOKING NORTHEAST TOWARD THE REAR OF THE STRUCTURE. THE WHEELS AT THE TOP OF THE TRAM BUCKETS RODE OFF THE STATIONARY CABLES ONTO THE TRACK SUPPORTED BY THE "C" IRONS SUSPENDED FROM THE TOP TIMBERS, CLEARLY SEEN AT THE TOP OF THE FRAME. THE ANCHOR POINTS FOR THE TWO STATIONARY CABLES ARE AT BOTTOM CENTER, JUST BELOW THE CABLE WHEEL. THE MAIN CABLE WHEEL IS IN THE DISTANCE AT CENTER LEFT. THE ORE CHUTES COMING FROM THE ORE BIN ARE AT LEFT CENTER EDGE. TRAM BUCKETS WERE CHARGED HERE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, AND LOADING PLATFORM. LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-47(CT) FOR IDENTICAL COLOR TRANSPARENCY. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM TRESTLE, AND LOADING PLATFORM, LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-13 FOR IDENTICAL B&W NEGATIVE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

7. TROJAN MILL, EXTERIOR FROM NORTHWEST, c. 191828. ADDITIONS FOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. TROJAN MILL, EXTERIOR FROM NORTHWEST, c. 1918-28. ADDITIONS FOR PRIMARY THICKENERS No. 1 AND No. 2, SECONDARY THICKENERS No. 1, No. 2, AND No. 3, AGITATORS, AIR COMPRESSOR, AND PORTLAND FILTERS ARE SHOWN COMPLETE. STAIR ON NORTH SIDE OF CRUDE ORE BINS IS PRESENT AS IS THE LIME BIN ADJACENT TO THE WEST CRUDE ORE BIN, AND THE SNOW SHED ADDED OVER THE TRAMLINE SERVING THE EAST AND WEST CRUDE ORE BINS. ALSO PRESENT IS THE BABBITT HOUSE AND ROCK BIN. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

10. DETAILED VIEW OF THE EAST ELEVATION. THE UPPER SET ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. DETAILED VIEW OF THE EAST ELEVATION. THE UPPER SET OF WINDOWS PROVIDE LIGHT FOR THE DELIVERY LEVEL. THE LOWER SETS OF WINDOWS PROVIDE LIGHT TO THREE STORY SPACE BENEATH THE DELIVERY LEVEL AND BEHIND THE ORE STORAGE BINS. NOTE THE ORE DELIVER TRESTLE AT THE TIME THE PHOTOGRAPH WAS TAKEN, THE MODERN CEMENT MIXER AND WHEELBARROWS WERE FOR THIS WORK. NOTE THE MORTAR BOXES ON THEIR SIDES. IT IS UNCLEAR IF THESE WERE FROM EARLIER STAMPS AT THIS MILL OR IF THEY WERE BROUGHT TO THE SITE FROM OTHER MILLS IN THE REGION. RISDON IRON WORKS IS CAST INTO THE MORTARS AND THEY ALSO BEAR A PLATE: WHITE, ROGERS AND CO. MILL WRIGHTS. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

53. VIEW OF CRUSHED OXIDIZED ORE BIN FROM EAST. SHOWS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

53. VIEW OF CRUSHED OXIDIZED ORE BIN FROM EAST. SHOWS ACCESS STAIR TO FEED LEVEL; DUST COLLECTOR ON LEFT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

DETAIL VIEW OF BALL MILL FEED SYSTEM, MOUTH OF CLASSIFIER, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF BALL MILL FEED SYSTEM, MOUTH OF CLASSIFIER, AND ORE BIN CHUTE, LOOKING EAST NORTHEAST. CRUSHED ORE FROM THE SECONDARY ORE BIN WAS INTRODUCED INTO THE FEED TROUGH VIA A CHUTE. AS THE BALL MILL TURNED, THE ROUND SCOOP ALSO TURNED IN THE TROUGH TO CHANNEL ORE INTO THE BALL MILL. SEE CA-292-14 FOR IDENTICAL B&W NEGATIVE. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

DETAIL VIEW OF BALL MILL FEED SYSTEM, MOUTH OF CLASSIFIER, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF BALL MILL FEED SYSTEM, MOUTH OF CLASSIFIER, AND ORE BIN CHUTE, LOOKING EAST NORTHEAST. CRUSHED ORE FROM THE SECONDARY ORE BIN WAS INTRODUCED INTO THE FEED TROUGH VIA A CHUTE. AS THE BALL MILL TURNED, THE ROUND SCOOP ALSO TURNED IN THE TROUGH TO CHANNEL ORE INTO THE BALL MILL. SEE CA-292-20 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ABOVE ORE BIN, LOOKING WEST FROM TOP OF STAIRWAY IN CA-290-25. THE PIPE AT CENTER WAS USED TO SPREAD CRUSHED ORE COMING FROM THE JAW CRUSHER EVENLY TO ALL AREA OF THE ORE BIN BELOW. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

55. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN ADDITION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN ADDITION TO RIGHT (WEST) WITH BAKER COOLER IN FRONT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

31. VIEW FROM SOUTHWEST TO CORNER WHERE SAMPLING/CRUSHING ADDITIONS ABUT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. VIEW FROM SOUTHWEST TO CORNER WHERE SAMPLING/CRUSHING ADDITIONS ABUT CRUSHED OXIDIZED ORE BIN. INTACT BARREN SOLUTION TANK VISIBLE IN FRONT OF CRUSHED ORE BIN. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

36. INTERIOR VIEW LOOKING WEST FROM UNDERNEATH THE ORE BINS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. INTERIOR VIEW LOOKING WEST FROM UNDERNEATH THE ORE BINS LOOKING AT THE BACK SIDE OF THE HENDY CHALLENGE CONTINUOUS ORE FEEDERS, #1 IS ON THE LEFT, #2 IS CENTER, AND #3 IS ON THE RIGHT. THESE ARE USED TO KEEP A CONTINUOUS FLOW OF ORE INTO THE STAMP MILLS. NOTE THE SPARE FEEDER DISKS ON THE FLOOR BOTTOM CENTER AND SPARE STAMP HEADS AND SHOES ON THE FLOOR BOTTOM LEFT OF THE IMAGE. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

ORE CONVEYANCE SYSTEM AND ADIT. LOOKING WEST. ORE FROM THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ORE CONVEYANCE SYSTEM AND ADIT. LOOKING WEST. ORE FROM THE MINES ABOVE AT THE RIDGELINE AND TO THE RIGHT WAS CONVEYED TO THIS AREA AND DUMPED INTO THE SHAFT AT CENTER. THIS SHAFT OPENS INTO THE ADIT AT BOTTOM CENTER. THERE IS ANOTHER SHAFT OPENING INTO THE ADIT JUST ABOVE THE ADIT BEHIND THE STONE WALL. THE ORE WAS LOADED INTO TRAM CARS INSIDE THE ADIT AND CONVEYED ON TRACKS TO THE TRESTLE LEADING TO THE PRIMARY ORE BIN AT THE TRAM TERMINAL. TRACKS CAN BE SEEN LEADING FROM THE ADIT AND TO THE LEFT. THE ORE WAS THEN DUMPED INTO A CHUTE AT THE END OF THE TRESTLE CARRYING IT INTO THE ORE BIN AT THE TRAM TERMINAL(SEE CHUTE ON CA-291-30). - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL VIEW OF FILTER PRESS REMAINS, BOILER, SECONDARY ORE BIN, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF FILTER PRESS REMAINS, BOILER, SECONDARY ORE BIN, TRAM TRESTLE AND WATER TANK, LOOKING NORTHWEST. HIS VIEW IS TAKEN FROM THE THIRD LEVEL OF THE MILL, NEARBY THE BLACKSMITH'S FORGE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

56. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN TOWER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

56. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN TOWER WAS FED BY THE 14 INCH BELT CONVEYOR SUPPORTED ON BENT, LOWER RIGHT. THE ROTATING BAKER COOLER IS SUPPORTED BY A CONCRETE FOUNDATION TROUGH. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

167. VIEW OF DUST COLLECTOR AND CRUSHED OXIDIZED ORE BIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

167. VIEW OF DUST COLLECTOR AND CRUSHED OXIDIZED ORE BIN FROM EAST. THE DUCTWORK TO TOP OF COLLECTOR (OPEN END, MIDDLE LEFT) CONNECTED TO HOODS OVER SYMONS SCREEN, ROD MILL, AND BAKER COOLER DISCHARGE - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

52. VIEW OF DUST COLLECTOR AND CRUSHED OXIDIZED ORE BIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

52. VIEW OF DUST COLLECTOR AND CRUSHED OXIDIZED ORE BIN FROM EAST. THE DUCTWORK TO TOP OF COLLECTOR (OPEN END, MIDDLE LEFT) CONNECTED TO HOODS OVER SYMONS SCREEN, ROD MILL, AND BAKER COOLER DISCHARGE. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

22. GENERAL VIEW OF MILL FROM SOUTHEAST. PROMINENT ARE THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. GENERAL VIEW OF MILL FROM SOUTHEAST. PROMINENT ARE THE 100-TON STEEL CRUSHED UNOXIDIZED ORE BIN, CENTER LEFT; STEPHENS-ADAMSON 15 TON/HR INCLINED BUCKET ELEVATOR IN FRONT OF THE STEEL ORE BIN; AND THE BAKER COOLER, LOWER RIGHT. THESE MACHINES AND OTHERS IN THE AREA WERE PART OF THE UNOXIDIZED ORE CIRCUIT. THE ROASTER IS OUT OF THE PICTURE TO THE RIGHT (EAST). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

1. EAGLE MILL EXTERIOR FROM NORTHWEST, c. 1907. SHOWS INITIAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EAGLE MILL EXTERIOR FROM NORTHWEST, c. 1907. SHOWS INITIAL MILL CONFIGURATION WITH FULLY EXPOSED CRUDE ORE BIN CONCRETE RETAINING WALL, SINGLE (SOUTH) CRUDE ORE BIN, AND EXPOSED CRUSHER HOUSE. NOTE THE LACK OF MACHINE SHOP OR SNOW SHEDS. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

47. VIEW OF FEED LEVEL, CRUSHED OXIDIZED ORE BIN FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

47. VIEW OF FEED LEVEL, CRUSHED OXIDIZED ORE BIN FROM EAST. THE 18 INCH BELT CONVEYOR FEED IS AT CENTER, WITH DRIVE GEAR. THE 16 INCH FINES FEED IS IN THE BACKGROUND AND 18 INCH BELT CONVEYOR DISCHARGE IS SLIGHTLY RIGHT OF CENTER. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

EAST ELEVATION OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. TRAM CARS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EAST ELEVATION OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. TRAM CARS ENTERED AND EXITED FROM RIGHT,AND DUMPED INTO THE ORE BIN SEEN AT LOWER LEFT. BELOW THE ORE BIN IS A JAW CRUSHER FOUNDATION. THE WOODEN BOX AT CENTER IS FILLED WITH ROCKS, PROVIDING THE COUNTERWEIGHT TO THE TRAMWAY CABLE, WHICH KEEPS IT TAUGHT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

60. VIEW OF ROASTER ADDITION FROM WEST, LOCATION OF SYMONS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. VIEW OF ROASTER ADDITION FROM WEST, LOCATION OF SYMONS 3 BY 8 FEET VIBRATING SCREEN. SHOWS BAKER COOLER WITH DUST COLLECTOR DUCT AND DISCHARGE CHUTE ON LEFT. THE 14 INCH BELT CONVEYOR WAS SUPPORTED ON TWO BENTS IN CENTER OF VIEW AS IT CONNECTED WITH THE BUCKET ELEVATOR/ORE BIN TOWER, WHICH IN TURN FED THE ROASTER (BEHIND). THE BASE OF THE ROASTER EXHAUST STACK IS AT THE UPPER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

34. VIEW FROM CRUSHED OXIDIZED ORE BIN WEST TO THICKENER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. VIEW FROM CRUSHED OXIDIZED ORE BIN WEST TO THICKENER ADDITIONS. SHAFT OF PRIMARY THICKENER No. 1 AT CENTER, WITH PRIMARY THICKENER No. 2 ABOVE AND TO THE LEFT. INTACT THICKENER SURGE TANK IS JUST ABOVE AND TO THE RIGHT (NORTH). ALL FRAMING ABOVE SECONDARY THICKENERS No. 2, No. 3, AND No. 7 HAS COLLAPSED. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

27. VIEW OF CENTRAL SECTION OF MILL FROM NORTHEAST. LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. VIEW OF CENTRAL SECTION OF MILL FROM NORTHEAST. LEVELS OF MILL VISIBLE IN ROOF LINES INCLUDE CRUSHED OXIDIZED ORE BIN (OPEN FRAMING, TOP CENTER), MILLING FLOOR (FIRST ROOF DOWN FROM ORE BIN), LEACHING/OLD SAND TANK LEVEL (SHALLOWER SECOND ROOF DOWN), GOLD TANK/AGITATOR LEVEL (CENTER), AND PRECIPITATION LEVEL WITH SUMP LEVEL BELOW (LOWER RIGHT). ROOF BREAKS ALLOWED FOR CLERESTORY WINDOWS WHICH ILLUMINATED THE INTERIORS, ALONG WITH DORMERS. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

51. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS BAKER COOLER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

51. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS BAKER COOLER AT LOWER LEFT, AND FOUNDATIONS FOR ROD MILL BETWEEN COOLER AND STEPHENS-ADAMSON INCLINED BUCKET ELEVATOR. THE BELT CONVEYOR TO RIGHT OF ELEVATOR FED ELEVATOR FROM ROD MILL. 100-TON ORE BIN AND DUST COLLECTOR IS BEHIND FRAMING BENT. NOTE CONVEYOR EMERGING FROM BOTTOM OF ORE BIN, THIS AND THE INCLINED ELEVATOR FED THE SYMONS SCREEN (MISSING). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

12. VIEW FROM EAST OF THE MILL AND TRESTLE SHOWING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. VIEW FROM EAST OF THE MILL AND TRESTLE SHOWING THE ORE RECEIVING STATION. THE ORE BIN AND CHUTE FOR RECEIVING ORE AND LOADING IT INTO CARS FOR DELIVERY ACROSS THE TRESTLE TO THE MILL IS VISIBLE AT THE BOTTOM OF THE PHOTO. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE JAW CRUSHER FOUNDATION CAN BE CLEARLY SEEN AT CENTER LEFT WITH A CONVEYOR TO CARRY CRUSHED ORE UP TO THE SECONDARY ORE BIN,LEFT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

5. TROJAN MILL, PRIMARY THICKENER No. 1 FROM WEST, c. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. TROJAN MILL, PRIMARY THICKENER No. 1 FROM WEST, c. 1914. TANK BARREL IS COMPLETE, BUT ADDITION ENCLOSURE NOT YET BEGUN. SAMPLING ADDITION SOUTH OF CRUSHED ORE BIN (CHANGE OF SIDING COLOR SHOWN AS COMPLETE. ROCK BIN VISIBLE ON FAR RIGHT. CREDIT WR. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

38. VIEW OF CRUSHER ROOM FROM NORTH. THE CRUSHER IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. VIEW OF CRUSHER ROOM FROM NORTH. THE CRUSHER IS MISSING, BUT THREE GRIZZLIES AND THE FEED GATE FROM THE SOUTH ORE BIN ARE STILL VISIBLE. PULLEY AT BOTTOM OF THE VIEW IS THE BEGINNING OF THE 24 INCH BELT CONVEYOR. NOTE SOUTH BIN DIAGONAL SHEATHING MATCHES THAT IN VIEW SD-2-3. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

9. TROJAN MILL, EXTERIOR FROM NORTHWEST, c. 191828. WINTER SNOW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. TROJAN MILL, EXTERIOR FROM NORTHWEST, c. 1918-28. WINTER SNOW SHOWS LINE OF CRUDE ORE BIN STAIR. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

32. DETAIL OF WALL SHOWN IN SD231. BEHIND WALL FRAMING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. DETAIL OF WALL SHOWN IN SD-2-31. BEHIND WALL FRAMING IS SAMPLING ROOM WITH WOOD SAMPLING ELEVATOR. CRUSHED OXIDIZED ORE BIN ON LEFT (SOUTH). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

63. DETAIL OF TRAVELING CRANE TRUSS FROM NORTHEAST. TRUSS IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

63. DETAIL OF TRAVELING CRANE TRUSS FROM NORTHEAST. TRUSS IS IN FRONT OF CRUSHED OXIDIZED ORE BIN. THE BARREN SOLUTION TANK IS JUST VISIBLE IN RIGHT BACKGROUND. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

6. TROJAN MILL, PRIMARY THICKENER No. 1 FROM WEST, c. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. TROJAN MILL, PRIMARY THICKENER No. 1 FROM WEST, c. 1914. TANK COMPLETED PRIOR TO ADDITION OF ENCLOSURE. ADDITION FOR BARREN SOLUTION TANK JUST VISIBLE BETWEEN THICKENER AND CRUSHED ORE BIN. CREDIT WR. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Effect of horizontal pick and place locations on shoulder kinematics.

PubMed

Könemann, R; Bosch, T; Kingma, I; Van Dieën, J H; De Looze, M P

2015-01-01

In this study the effects of horizontal bin locations in an order picking workstation on upper arm elevation, trunk inclination and hand use were investigated. Eight subjects moved (self-paced) light or heavy products (0.2 and 3.0 kg) from a central product bin to an inner or outer order bin (at 60 or 150 cm) on the left or right side of the workstation, while movements were recorded. The outer compared to inner bin location resulted in more upper arm elevation and trunk inclination per work cycle, both in terms of number of peak values and in terms of time integrals of angles (which is a dose measure over time). Considering the peak values and time integrals per minute (instead of per work cycle), these effects are reduced, due to the higher cycle times for outer bins. Hand use (left, right or both) was not affected by order bin locations.

9. 5TH FLOOR, INTERIOR DETAIL TO EAST OF SOAP BIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. 5TH FLOOR, INTERIOR DETAIL TO EAST OF SOAP BIN No. 4: UPPER SCREWS MOVED SOAP CHIPS HORIZONTALLY FROM BIN TO BIN; LOWER LEFT-AND RIGHT-HAND SCREWS MOVED CHIPS TO CHUTE LEADING TO 3RD FLOOR SOAP MILLS - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

2. EXTERIOR VIEW, LOOKING NORTHEAST FROM THE CUPOLA (RIGHT) TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. EXTERIOR VIEW, LOOKING NORTHEAST FROM THE CUPOLA (RIGHT) TO COKE BIN (LEFT), OF RAW MATERIALS YARD. FOUNDRY IRON IS FROM SCRAP, NOT BASIC ORE. RAW MATERIALS ASSEMBLED, IN PILES, FOR SMELTING ARE AUTOMOTIVE SCRAP (CENTER), STRUCTURAL STEEL AND RAILROAD RAIL (RIGHT) AND LIMESTONE (LEFT). - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

3. VIEW OF EMPIRE STATE MINE WITH TAILING PILE IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW OF EMPIRE STATE MINE WITH TAILING PILE IN BOTTOM LEFT AND COLLAPSED ADIT LOCATED BELOW DARK SHADOWS IN FAR RIGHT/LOWER THIRD. COLLAPSED BUILDING AND PARTIAL VIEW OF ORE CHUTE/BIN IS VISIBLE ON HILLSIDE ABOVE TAILINGS. CAMERA POINTED NORTH/NORTHWEST. - Florida Mountain Mining Sites, Empire State Mine, West side of Florida Mountain, Silver City, Owyhee County, ID

Water quality data at selected sites in the Mississippi Valley-type Zn-Pb ore district of upper Silesia, Poland, 1995-97

USGS Publications Warehouse

Wirt, Laurie; Motyka, Jacek; Leach, David; Sass-Gustkiewicz, Maria; Szuwarzynski, Marek; Adamczyk, Zbigniew; Briggs, Paul; Meiers, Al

2003-01-01

The water chemistry of aquifers and streams in the Upper Silesia Ore District, Poland are affected by their proximity to zinc, lead, and silver ores and by ongoing mining activities that date back to the 11th century. This report presents hydrologic and water-quality data collected as part of a collaborative research effort of the U.S. Geological Survey and the University of Mining and Metallurgy in Cracow, Poland to study Mississippi-Valley-Type lead-zinc deposits. MVT deposits in the Upper Silesia Ore District (Fig. 1) were selected for detailed study because the Polish mining industry allowed access to collect samples from underground mines and mine-land property. Water-quality samples were collected from streams, springs, wells, underground mine seeps and drains; and mine-tailings ponds. Data include field measurements of specific conductance, pH, water temperature, and dissolved oxygen and laboratory analyses of major and minor inorganic constituents and selected trace-element constituents.

2. VIEW OF RUINS OF FINE ORE MILL (FEATURE 20), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. VIEW OF RUINS OF FINE ORE MILL (FEATURE 20), FACING NORTH-NORTHWEST. PORTION OF HEADFRAME AND STORAGE TANKS (FEATURE 18) VISIBLE IN UPPER RIGHT CORNER OF PHOTOGRAPH. - Copper Canyon Camp of the International Smelting & Refining Company, Ruins of the Fine Ore Mill, Copper Canyon, Battle Mountain, Lander County, NV

A conceptual model of the copper-porphyry ore formation based on joint analysis of deep 3D geophysical models: Sorskoe complex (Russia) case study

NASA Astrophysics Data System (ADS)

Spichak, Viacheslav V.; Goidina, Alexandra G.

2017-12-01

Joint analysis of deep three-dimensional models of the electrical resistivity, seismic velocity, and density of the complex hosting the Sorskoe Cu-Mo deposit (Russia) is carried out aimed at finding geophysical markers characterizing the areas of ore generation, transportation and deposition. The three-dimensional lithology model of the study area is built based on the empirical relationship between the silica content of the rocks and seismic velocities. It is in agreement with geological and geochemical studies provided in this area earlier and could be used as a basis for forecasting locations of the copper-molybdenum ore deposits at depth. A conceptual model of the copper-porphyry complex explaining the mechanisms of ore generation, transportation from the lower to the upper crust and deposition in the upper crust is suggested. In particular, it is supposed that post-magmatic supercritical gas-water ore-bearing fluids are upwelling through the plastic crust due to the sliding of the fluid films along the cleavage planes of the foliated rocks while at the depths of the brittle upper crust this mechanism could be changed by volumetric fluid transportation along the network of large pores and cracks.

110. MILL APPROACH FROM EAST. THE TRAM LINE RANT TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

110. MILL APPROACH FROM EAST. THE TRAM LINE RANT TO THE RIGHT (NORTH) OF THE ROAD AND REACHED THE CRUDE ORE BINS AROUND THE FAR BEND. BUILDINGS FROM FRONT TO BACK ARE, ON RIGHT, OIL WAREHOUSE AND GASOLINE SHED, AND ON LEFT, GARAGE, CARPENTER'S SHOP, OIL SHED, AND MACHINE SHOP. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

23. VIEW OF EAST END OF MILL. THE FOUR GENERAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. VIEW OF EAST END OF MILL. THE FOUR GENERAL LEVELS OF THE MILL ARE SHOWN STEPPING DOWN THE HILLSIDE FROM SOUTH TO NORTH. THE 100-TON STEEL ORE BIN AND STEPHENS-ADAMSON 15TON INCLINED BUCKET ELEVATOR ARE ON THE CRUSHING LEVEL AT RIGHT. FROM LEFT TO RIGHT THE OTHER LEVELS ARE MILLING, LEACHING AND PRECIPITATION. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

41. INTERIOR VIEW LOOKING NORTH ON THE MAIN POWER SHAFT/CAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. INTERIOR VIEW LOOKING NORTH ON THE MAIN POWER SHAFT/CAM LEVEL LOOKING TOWARD THE STAMP BATTERIES. NOTE THE UN-HEWN LUMBER SPANNING THE LARGE TIMBER FRAME STRUCTURAL MEMBERS, IT IS BELIEVED THESE WERE ADDED LATER TO ADD ADDITIONAL STABILITY TO THE STAMP BATTERIES. ALSO NOTE THE ORE BINS AND ROCK CRUSHER BEHIND THE BATTERIES. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Stratigraphy of Zambian copperbelt orebodies

NASA Astrophysics Data System (ADS)

Binda, Pier L.

1994-11-01

The subdivision of the Roan Supergroup in three informal units instead of the traditional Lower Roan/Upper Roan allows a better understanding of facies relationships. The lower division (Siliciclastic Unit) consists of a variable thickness of continental conglomerates and erenites. The middle division (Mixed Unit) consists of a wedge of carbonate and siliciclastic lithologies tapering to the south-west and deposited in a shallow sea. The upper division (Carbonate Unit or Upper Roan s.s.) is a thick succession of dolostones, subordinate argillites and breccias that directly overlies, but is probably in tectonic contact with, the Siliciclastic Unit in the south-western part of the Copperbelt. Reference boundaries for the Mixed and Siliciclastic Units are given for all mining localities of the Zambian Copperbelt. The basal part of the Mixed Unit, host to the most important CuCo orebodies, was deposited during a major marine transgression which, proceeding from SW-NE, swiftly inundated the whole Copperbelt basin. Thus, the Mufulira Ore Formation can be considered as the near-shore facies of the basinal ore shale. The transition from the Mufulira arenites to the Chambishi silty, ore shale has been effaced by erosional or tectonic stripping of the Roan sediments on the Kafue anticline, whereas the transition from silty to carbonaceous ore shale is well documented in the southern part of the Chambishi-Nkana basin. Concomitant with the NE-SW lithofacies changes within the basal Mixed Unit, there is marked decrease in Cu grade and content from the Mufulira wacke and arenite to the silty ore shale of the northern Chambishi basin and the carbonaceous and pyritic ore shale of the southern Chambishi basin. Cobalt is virtually absent in the Mufulira Ore Formation, reaches ore grade in the silty ore shale and occurs in trace amounts in the carbonaceous ore shale. Thus, the correlation of the basal Mixed Unit reveals a hitherto undetected regional metal zoning akin to that noted in parts of individual Copperbelt basin. The middle portion of the Mixed Unit contains at least one laterally continuous Cu mineralization in the arkosic arenite with minor occurrences of local significance. The Siliciclastic Unit contains Cu concentrations at several stratigraphical levels, but precise correlation of footwall orebodies is precluded by the heterogeneity of the clastic wedges of local provenance. The Mixed Unit of the Zambian Copperbelt can be correlated lithostratigraphically with the Serie des Mines of Shaba. A bed-by-bed correlation of the Kamoto (Zaire) and Mindola (Zambia) Ore Formations is proposed. The southern provenance of the Shaba nappes is supported.

Regional Variations in the Earth's upper inner core

NASA Astrophysics Data System (ADS)

Stroujkova, A.; Cormier, V. F.

2003-12-01

Strong regional variations in seismic velocity and attenuation have been observed in the uppermost layer of the inner core. Different studies suggest hemispherical differences within this transitional layer, with eastern hemisphere faster than the western (e.g. Garcia, 2002; Wen and Niu, 2002). The scale and the depth dependence of the heterogeneities are still in debate. In order to systematically study smaller scale heterogeneities we selected a data set of PKIKP and PKiKP phases with epicentral distances between 120\\deg and 140\\deg. The upper layer of the inner core was divided into `bins' and the seismograms were gathered into these bins according to the ray turning points. After correcting for source, site and propagation effects we stacked traces with close epicentral distance within each bin to improve signal-to-noise ratio. Finally we performed full 3D modeling of the obtained waveforms.

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER “HOT SHOT” ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-4 FOR IDENTICAL B&W NEGATIVE. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER “HOT SHOT” ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-17 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

Manganese oxides and associated minerals as constituents of dispersed mineralization of metasomatic rocks in the Dukat ore field

NASA Astrophysics Data System (ADS)

Filimonova, L. G.; Sivtsov, A. V.; Trubkin, N. V.

2010-08-01

Lithiophorite and coronadite—varieties of vernadite and todorokite—make up finely dispersed colloform mixtures along with minor grains and nanoparticles of aluminosilicates and ore minerals in metasomatic rocks of the Dukat ore field, which were formed in local areas of fluid and hydrothermal-solution discharge at the upper level of the ore-forming system. Fe-vernadite associates with feroxyhyte, magnetite, apatite, K-feldspar, native silver, and acanthite in greisenized granitoids and with epidote, cerianite, plattnerite, and Fe-chlorite in quartz-garnet-chlorite propylites. Todorokite with high Pb, Tl, and Sn contents associates with epidote, albite, bitumen, and native silver in quartz-epidote-chlorite propylites. Al-vernadite, coronadite, and lithiophorite associate with opal, kaolinite, Fe-chlorite, zincite, uraninite, native silver, and acanthite in argillisites. These data allowed us to estimate the conditions of manganese accumulation in the epithermal ore-forming system and deposition conditions of Mn-rich, finely dispersed mineral mixtures in mineralized zones hosted in metasomatic rocks of the ore field.

The volcanic-sedimentary sequence of the Lousal deposit, Iberian Pyrite Belt (Portugal)

NASA Astrophysics Data System (ADS)

Rosa, Carlos; Rosa, Diogo; Matos, Joao; Relvas, Jorge

2010-05-01

The Iberian Pyrite Belt (IPB) is a massive sulfide province that is located in the south of Portugal and Spain, and hosts more than 90 massive sulfide deposits that amount to more than 1850 million metric tonnes of sulfide ore (Tornos, 2006). The ore deposits size, vary from ~1Mt to >100Mt (e.g. Neves Corvo and Aljustrel in Portugal, and Rio Tinto and Tharsis in Spain). The ore deposits are hosted by a submarine sedimentary and volcanic, felsic dominated, succession that constitutes the Upper Devonian to Lower Carboniferous Volcanic and Sedimentary Complex (VSC). The VSC ranges in thickness from approximately 600 to 1300 m (Tornos 2006). The VSC overlies the Phyllite-Quartzite Group (PQ) (Upper Devonian, base unknown) and is overlain by the Baixo Alentejo Flysch Group (Lower to Upper Carboniferous). The Lousal massive sulfide deposit is located in the western part of the IPB and occurs mostly interbedded with black mudstone. The VSC sequence at Lousal mine consists of a mudstone and quartzite sequence (PQ Group) in the lower part of the succession, over which a thick sequence of rhyolitic lavas (>300 m) occurs. Above the rhyolitic lavas there is a thick sequence of black and grey mudstone that hosts the massive sulfide ore bodies, and a rhyolitic sill. The upper part of the VSC sequence consists of a thick mudstone interval that hosts two thick basaltic units, locally with pillows. The rhyolites have small coherent cores, locally with flow bands, that grade to surrounding massive clastic intervals, with large lateral extent. The clasts show jigsaw-fit arrangement in many places and have planar or curviplanar margins and locally are perlitic at the margin. The top contact of these units is in most locations not exposed, which makes difficult to interpret the mode of emplacement. However, the thick clastic intervals, above described, are in accordance with quenching of volcanic glass with abundant water and therefore indicate that quenching of the rhyolites was the dominant fragmentation mechanism. Unlike many locations of the IPB, fiamme-rich pyroclastic units were not identified at Lousal. The ore deposits occur in close proximity with this volcanic centre that may have driven hydrothermal circulation that led to ore formation. The volcanic rocks show intense chloritic alteration, indicating that the mineralizing event occurred after most of the rhyolitic units have emplaced. The massive sulfides show abundant sedimentary structures which is not typical in the massive sulfide deposits of the IPB. The Lousal 50 Mt massive sulfide deposit consists of at least 11 ore bodies and was exploited until 1988 mainly for pyrite. The ores mined averaged 0.7% Cu, 0.8%Pb e 1.4%Zn (Strauss, 1971). These relatively low base metal grades led to an evaluation of the contents and distribution of high-tech element in the ore bodies, which would improve the economic viability of mining the deposit. This evaluation is currently focusing on the distribution and mineralogy of selenium, as ores mined in the past were known to be rich in this element. This work benefits from research projects INCA (PTDC/CTE-GIN/67027/2006; Characterization of crucial mineral resources for the development of renewable energy technologies: The Iberian Pyrite Belt ores as a source of indium and other high-technology elements) and project ARCHYMEDES II (POCTI/CTA/45873/2002), both funded by the Fundação para a Ciência e Tecnologia. REFERENCES Strauss, G.K., 1970. Sobre la geologia de la provincia piritifera del Suroeste de la Peninsula Iberica y sus yacimientos, en especial sobre la mina de pirita de Lousal (Portugal): Memoria del IGME 77, 1-266. Tornos, F., 2006. Environment of formation and styles of volcanogenic massive sulfides: The Iberian Pyrite Belt. Ore Geology Reviews 28, 259-307.

Magnetic properties of sediments in cores from the Mandovi estuary, western India: Inferences on provenance and pollution.

PubMed

Prajith, A; Rao, V Purnachandra; Kessarkar, Pratima M

2015-10-15

Magnetic properties of sediments were investigated in 7 gravity cores recovered along a transect of the Mandovi estuary, western India to understand their provenance and pollution. The maximum magnetic susceptibility of sediments was at least 6 times higher in the upper/middle estuary than in lower estuary/bay. The χfd% and χARM/SIRM of sediments indicated coarse, multi-domain and pseudo-single domain magnetic grains, resembling ore material in the upper/middle estuary and coarse stable single domain (SSD) to fine SSD grains in the lower estuary/bay. Mineralogy parameters indicated hematite and goethite-dominated sediments in the upper/middle estuary and magnetite-dominated sediments in the lower estuary/bay. Two sediment types were discernible because of deposition of abundant ore material in the upper/middle estuary and detrital sediment in the lower estuary/bay. The enrichment factor and Index of geo-accumulation of metals indicated significant to strong pollution with respect to Fe and Mn in sediments from the upper/middle estuary. Copyright © 2015 Elsevier Ltd. All rights reserved.

The north-subducting Rheic Ocean during the Devonian: consequences for the Rhenohercynian ore sites

NASA Astrophysics Data System (ADS)

von Raumer, Jürgen F.; Nesbor, Heinz-Dieter; Stampfli, Gérard M.

2017-10-01

Base metal mining in the Rhenohercynian Zone has a long history. Middle-Upper Devonian to Lower Carboniferous sediment-hosted massive sulfide deposits (SHMS), volcanic-hosted massive sulfide deposits (VHMS) and Lahn-Dill-type iron, and base metal ores occur at several sites in the Rhenohercynian Zone that stretches from the South Portuguese Zone, through the Lizard area, the Rhenish Massif and the Harz Mountain to the Moravo-Silesian Zone of SW Bohemia. During Devonian to Early Carboniferous times, the Rhenohercynian Zone is seen as an evolving rift system developed on subsiding shelf areas of the Old Red continent. A reappraisal of the geotectonic setting of these ore deposits is proposed. The Middle-Upper Devonian to Early Carboniferous time period was characterized by detrital sedimentation, continental intraplate and subduction-related volcanism. The large shelf of the Devonian Old Red continent was the place of thermal subsidence with contemporaneous mobilization of rising thermal fluids along activated Early Devonian growth faults. Hydrothermal brines equilibrated with the basement and overlying Middle-Upper Devonian detrital deposits forming the SHMS deposits in the southern part of the Pyrite Belt, in the Rhenish Massif and in the Harz areas. Volcanic-hosted massive sulfide deposits (VHMS) formed in the more eastern localities of the Rhenohercynian domain. In contrast, since the Tournaisian period of ore formation, dominant pull-apart triggered magmatic emplacement of acidic rocks, and their metasomatic replacement in the apical zones of felsic domes and sediments in the northern part of the Iberian Pyrite belt, thus changing the general conditions of ore precipitation. This two-step evolution is thought to be controlled by syn- to post-tectonic phases in the Variscan framework, specifically by the transition of geotectonic setting dominated by crustal extension to a one characterized by the subduction of the supposed northern slab of the Rheic Ocean preceding the general Late Variscan crustal shortening and oroclinal bending.

Trace- and rare-earth element geochemistry and Pb-Pb dating of black shales and intercalated Ni-Mo-PGE-Au sulfide ores in Lower Cambrian strata, Yangtze Platform, South China

NASA Astrophysics Data System (ADS)

Jiang, Shao-Yong; Chen, Yong-Quan; Ling, Hong-Fei; Yang, Jing-Hong; Feng, Hong-Zhen; Ni, Pei

2006-08-01

The Lower Cambrian black shale sequence of the Niutitang Formation in the Yangtze Platform, South China, hosts an extreme metal-enriched sulfide ore bed that shows >10,000 times enrichment in Mo, Ni, Se, Re, Os, As, Hg, and Sb and >1,000 times enrichment in Ag, Au, Pt, and Pd, when compared to average upper continental crust. We report in this paper trace- and rare-earth-element concentrations and Pb-Pb isotope dating for the Ni-Mo-PGE-Au sulfide ores and their host black shales. Both the sulfide ores and their host black shales show similar trace-element distribution patterns with pronounced depletion in Th, Nb, Hf, Zr, and Ti, and extreme enrichment in U, Ni, Mo, and V compared to average upper crust. The high-field-strength elements, such as Zr, Hf, Nb, Ta, Sc, Th, rare-earth elements, Rb, and Ga, show significant inter-element correlations and may have been derived mainly from terrigenous sources. The redox sensitive elements, such as V, Ni, Mo, U, and Mn; base metals, such as Cu, Zn, and Pb; and Sr and Ba may have been derived from mixing of seawater and venting hydrothermal sources. The chondrite-normalized REE patterns, positive Eu and Y anomalies, and high Y/Ho ratios for the Ni-Mo-PGE-Au sulfide ores are also suggestive for their submarine hydrothermal-exhalative origin. A stepwise acid-leaching Pb-Pb isotope analytical technique has been employed for the Niutitang black shales and the Ni-Mo-PGE-Au sulfide ores, and two Pb-Pb isochron ages have been obtained for the black shales (531±24 Ma) and for the Ni-Mo-PGE-Au sulfide ores (521±54 Ma), respectively, which are identical and overlap within uncertainty, and are in good agreement with previously obtained ages for presumed age-equivalent strata.

Massive deep-sea sulphide ore deposits discovered on the East Pacific Rise

USGS Publications Warehouse

Francheteau, Jean; Needham, H.D.; Choukroune, P.; Juteau, Tierre; Seguret, M.; Ballard, Richard D.; Fox, P.J.; Normark, William; Carranza, A.; Cordoba, D.; Guerrero, J.; Rangin, C.; Bougault, H.; Cambon, P.; Hekinian, R.

1979-01-01

Massive ore-grade zinc, copper and iron sulphide deposits have been found at the axis of the East Pacific Rise. Although their presence on the deep ocean-floor had been predicted there was no supporting observational evidence. The East Pacific Rise deposits represent a modern analogue of Cyprus-type sulphide ores associated with ophiolitic rocks on land. They contain at least 29% zinc metal and 6% metallic copper. Their discovery will provide a new focus for deep-sea exploration, leading to new assessments of the concentration of metals in the upper layers of the oceanic crust. ?? 1979 Nature Publishing Group.

Geology of the Midnite uranium mine, Stevens County, Washington; a preliminary report

USGS Publications Warehouse

Nash, J. Thomas; Lehrman, Norman J.

1975-01-01

The Midnite mine is one of only two mines in the United States currently producing uranium from discordant deposits in crystalline host rocks. Ore bodies are in metamorphosed steeply dipping Precambrian pelitic and calcareous rocks of a roof pendant adjacent to a Cretaceous(?) porphyritic quartz monzonite pluton. Production during 14 years, of operation has been about 8 million pounds of U3O8 from oxidized and reduced ores averaging 0.23 percent U3O8. Uranium deposits are generally tabular in form and dimensions range up to 380 m long, 210 m wide, and 50 m thick. Deposits are bounded on at least one side by unmineralized intrusive ribs of granitic rock, and thickest mineralized zones invariably occur at depressions in the intrusive contact. Upper limits of some deposits are nearly horizontal, and upper elevations of adjacent mineralized zones separated by ribs of granite are similar. Near surface ore is predominantly autunite, but ore at depth consists of pitchblende and coffinite with abundant pyrite and marcasite. Uranium minerals occur as .disseminations along foliation, replacements, and stockwork fracture-fillings. No stratigraphic controls on ore deposition are recognized. Rather, mineralized zones cut across lithologic boundaries if permeability is adequate. Most ore is in muscovite schist and mica phyllite, but important deposits occur in calc-silicate hornfels. Amphibolite sills and mid-Tertiary dacite dikes locally, carry ore where intensely fractured. High content of iron and sulfur, contained chiefly in FeS2, appear to be an important feature of favorable host rocks. Geometry of deposits, structural, and geochemical features suggest that uranium minerals were deposited over a span of time from late Cretaceous to late Tertiary. Ore occurs in but is not offset by a shear zone that displaces mid-Tertiary rocks.. Economic zones of uranium are interpreted to have been secondarily enriched in late Tertiary time by downward and lateral migration of uranium into permeable zones where deposition was influenced by ground water controls and minerals that could reduce or neutralize uranium-bearing solutions.

Lake Superior, Duluth, MN

NASA Technical Reports Server (NTRS)

1973-01-01

This view shows the west end of Lake Superior and Duluth, MN (47.0N, 91.0W). Portions of Minnesota, Michigan and Ontario, Canada are in the scene. The Duluth metropolitan area is at the west end of the lake. The discoloration plume in the water at Duluth is the result of tailings from the iron ore smelters that process the iron ore from the nearby open pit mines seen near the upper left corner of the photo.

Kinetic energy of Ps formed by Ore mechanism in Ar gas

NASA Astrophysics Data System (ADS)

Sano, Yosuke; Kino, Yasushi; Oka, Toshitaka; Sekine, Tsutomu

2015-06-01

In order to investigate kinetic energy of positronium(Ps) formed by Ore mechanism, we performed positron annihilation age-momentum correlation (AMOC) measurements in Argas for 5.0 MPa and 7.5 MPa at room temperature. From the time dependence of Doppler broadening of para-Ps (p-Ps) self-annihilation gramma-ray component, we observed Ps slowing down process. Using a simple slowing down model, we obtained the initial kinetic energy of Ps formed by Ore mechanism and Ps-Armomentum transfer cross section. The initial kinetic energy was 3.9 eV which was higher than the kinetic energy of Ps formed at the upper limit of Ore gap. The momentum transfer cross section was 0.019 ± 0.010 nm2 in between 1 eV and 3.9 eV, and was close to the theoretical calculation.

Stratigraphy of Upper Cretaceous and Cenozoic deposits of the Bakchar iron ore deposit (southwestern Siberia): New data

NASA Astrophysics Data System (ADS)

Lebedeva, N. K.; Kuzmina, O. B.; Sobolev, E. S.; Khazina, I. V.

2017-01-01

The results of complex palynological and microfaunistic studies of Upper Cretaceous and Cenozoic deposits of the Bakchar iron ore deposit are presented. Geochronologically, the age of the deposits varies from Campanian to Quaternary. It was established that the Slavgorod, Gan'kino, and Jurki (?) formations contain four biostratons in the rank of beds with dinocysts and three biostratons in the rank of beds with spores and pollen. The Cenozoic continental deposits contain four biostratons in the rank of beds, containing spores and pollen. As a result of the study, a large stratigraphic gap in the Cretaceous-Paleogene boundary deposits, covering a significant part of the Maastrichtian, Paleocene, Ypresian, and Lutetian stages of the Eocene, was established. The remnants of a new morphotype of heteromorphic ammonites of genus Baculites were first described in deposits of the Slavgorod Formation (preliminarily, upper Campanian). The distribution features of the different palynomorph groups in the Upper Cretaceous-Cenozoic deposits in the area of study due to transgressive-regressive cycles and climate fluctuations were revealed.

Dzhida Ore District: Geology, Structural and Metallogenic Regionalization, Genetic Types of Ore Deposits, Geodynamic Conditions of Their Formation, Forecast, and Outlook for Development

NASA Astrophysics Data System (ADS)

Gordienko, I. V.; Gorokhovsky, D. V.; Smirnova, O. K.; Lantseva, V. S.; Badmatsyrenova, R. A.; Orsoev, D. A.

2018-01-01

Based on complex structural, rheological, and metallogenic studies, taking into account the results of earlier subject-specific, prospecting, mapping, and exploration works, it has been established that the geological structure of the district was caused by the ensimatic evolution of the Vendian-Early Paleozoic Dzhida island-arc system, in which oceanic and island-arc complexes served as a melanocratic basement for Late Paleozoic-Mesozoic active within-plate (riftogenic) processes, which gave rise to the formation of ore deposits and occurrences of strategic mineral commodities (Mo, W, Au, Pt, Ag, and rare elements, including REE). Mantle plumes and flows of deep-seated transmagmatic solutions (ore-forming fluids) played a critical role in these processes, the significance of which increases in upper crustal swarms of dikes and fault systems. The forecasts and development prospects of the Dzhida ore district envisage the expansion of geological prospecting and exploration, scientific research, and technological testing of ore for insight into strategic mineral commodities, as well as reanimation of mining within the areas of the Dzhida's large territorial and industrial complex (TIC) in eastern Siberia.

Evolution of ore deposits on terrestrial planets

NASA Astrophysics Data System (ADS)

Burns, R. G.

Ore deposits on terrestrial planets materialized after core formation, mantle evolution, crustal development, interactions of surface rocks with the hydrosphere and atmosphere, and, where life exists on a planet, the involvement of biological activity. Core formation removed most of the siderophilic and chalcophilic elements, leaving mantles depleted in many of the strategic and noble metals relative to their chondritic abundances. Basaltic magma derived from partial melting of the mantle transported to the surface several metals contained in immiscible silicate and sulfide melts. Magmatic ore deposits were formed during cooling, fractional crystallization and density stratification from the basaltic melts. Such ore deposits found in earth's Archean rocks were probably generated during early histories of all terrestrial planets and may be the only types of igneous ores on Mars. Where plate tectonic activity was prevalent on a terrestrial planet, temporal evolution of ore deposits took place. Repetitive episodes of subduction modified the chemical compositions of the crust and upper mantles, leading to porphyry copper and molybdenum ores in calc-alkaline igneous rocks and granite-hosted tin and tungsten deposits. Such plate tectonic-induced mineralization in relatively young igneous rocks on earth may also have produced hydrothermal ore deposits on Venus in addition to the massive sulfide and cumulate chromite ores associated with Venusian mafic igneous rock. Sedimentary ore deposits resulting from mechanical and chemical weathering in reducing atmospheres in Archean earth included placer deposits (e.g., uraninite, gold, pyrite ores). Chromite, ilmenite, and other dense unreactive minerals could also be present on channel floors and in valley networks on Mars, while banded iron formations might underlie the Martian northern plains regions. As oxygen evolved in earth's atmosphere, so too did oxide ores. By analogy, gossans above sulfide ores probably occur on Mars, but not submarine ferromanganese nodules and crusts which have precipitated in oxygenated seawater on earth.

Evolution of ore deposits on terrestrial planets

NASA Technical Reports Server (NTRS)

Burns, R. G.

1991-01-01

Ore deposits on terrestrial planets materialized after core formation, mantle evolution, crustal development, interactions of surface rocks with the hydrosphere and atmosphere, and, where life exists on a planet, the involvement of biological activity. Core formation removed most of the siderophilic and chalcophilic elements, leaving mantles depleted in many of the strategic and noble metals relative to their chondritic abundances. Basaltic magma derived from partial melting of the mantle transported to the surface several metals contained in immiscible silicate and sulfide melts. Magmatic ore deposits were formed during cooling, fractional crystallization and density stratification from the basaltic melts. Such ore deposits found in earth's Archean rocks were probably generated during early histories of all terrestrial planets and may be the only types of igneous ores on Mars. Where plate tectonic activity was prevalent on a terrestrial planet, temporal evolution of ore deposits took place. Repetitive episodes of subduction modified the chemical compositions of the crust and upper mantles, leading to porphyry copper and molybdenum ores in calc-alkaline igneous rocks and granite-hosted tin and tungsten deposits. Such plate tectonic-induced mineralization in relatively young igneous rocks on earth may also have produced hydrothermal ore deposits on Venus in addition to the massive sulfide and cumulate chromite ores associated with Venusian mafic igneous rock. Sedimentary ore deposits resulting from mechanical and chemical weathering in reducing atmospheres in Archean earth included placer deposits (e.g., uraninite, gold, pyrite ores). Chromite, ilmenite, and other dense unreactive minerals could also be present on channel floors and in valley networks on Mars, while banded iron formations might underlie the Martian northern plains regions. As oxygen evolved in earth's atmosphere, so too did oxide ores. By analogy, gossans above sulfide ores probably occur on Mars, but not submarine ferromanganese nodules and crusts which have precipitated in oxygenated seawater on earth.

Lead-isotopic, sulphur-isotopic, and trace-element studies of galena from the Silesian-Cracow Zn-Pb ores, polymetallic veins from the Gory Swietokrzyskie MTS, and the Myszkow porphyry copper deposit, Poland

USGS Publications Warehouse

Church, S.E.; Vaughn, R.B.; Gent, C.A.; Hopkins, R.T.

1996-01-01

Lead-isotopic data on galena samples collected from a paragenetically constrained suite of samples from the Silesian-Cracow ore district show no regional or paragenetically controlled lead-isotopic trends within the analytical reproducibility of the measurements. Furthermore, the new lead-isotopic data agree with previously reported lead-isotopic results (R. E. Zartman et al., 1979). Sulfur-isotopic analyses of ores from the Silesian-Cracow district as well as from vein ore from the Gory Swietokrzyskie Mts. and the Myszkow porphyry copper deposit, when coupled with trace-element data from the galena samples, clearly discriminate different hydrothermal ore-forming events. Lead-isotopic data from the Permian and Miocene evaporite deposits in Poland indicate that neither of these evaporite deposits were a source of metals for the Silesian-Cracow district ores. Furthermore, lead-isotopic data from these evaporite deposits and the shale residues from the Miocene halite samples indicate that the crustal evolution of lead in the central and western European platform in southern Poland followed normal crustal lead-isotopic growth, and that the isotopic composition of crustal lead had progressed beyond the lead-isotopic composition of lead in the Silesian-Cracow ores by Permian time. Thus, Mesozoic and Tertiary sedimentary flysch rocks can be eliminated as viable source rocks for the metals in the Silesian-Cracow Mississippi Valley-type (MVT) deposits. The uniformity of the isotopic composition of lead in the Silesian-Cracow ores, when coupled with the geologic evidence that mineralization must post-date Late Jurassic faulting (E. Gorecka, 1991), constrains the geochemical nature of the source region. The source of the metals is probably a well-mixed, multi-cycle molasse sequence of sedimentary rocks that contains little if any Precambrian metamorphic or granitic clasts (S. E. Church, R. B. Vaughn, 1992). If ore deposition was post Late Jurassic (about 150 m. y.) or later as indicated by the geologic evidence, the source rocks probably contained elevated concentrations of Zn and Pb (75-100 ppm), and relatively low concentrations of U and Th (2 and 8 ppm or less, respectively). The Carboniferous coal-bearing molasse rocks of the Upper Silesian Coal Basin are a prime candidate for such a source region. The presence of ammonia and acetate in the fluid inclusions (Viets et al., 1996a) also indicate that the Carboniferous coal-bearing molasse sequence in the Upper Silesian Coal Basin may have been a suitable pathway for the MVT ore fluids. The lead-isotopic homogeneity, when coupled with the sulfur-isotopic heterogeneity of the ores suggests that mixing of a single metal-bearing fluid with waters from separate aquifers containing variable sulfur-isotopic compositions in karsts in the Muschelkalk Formation of Middle Triassic age may have been responsible for the precipitation of the ores of the Silesian-Cracow district.

Lake Superior, Deluth, MN

NASA Image and Video Library

1973-06-22

SL2-05-454 (22 June 1973) --- This view shows the west end of Lake Superior and Duluth, MN (47.0N, 91.0W). Portions of Minnesota, Michigan and Ontario, Canada are in the scene. The Duluth metropolitan area is at the west end of the lake. The discoloration plume in the water at Duluth is the result of tailings from the iron ore smelters that process the iron ore from the nearby open pit mines seen near the upper left corner of the photo. Photo credit: NASA

OPTHYLIC: An Optimised Tool for Hybrid Limits Computation

NASA Astrophysics Data System (ADS)

Busato, Emmanuel; Calvet, David; Theveneaux-Pelzer, Timothée

2018-05-01

A software tool, computing observed and expected upper limits on Poissonian process rates using a hybrid frequentist-Bayesian CLs method, is presented. This tool can be used for simple counting experiments where only signal, background and observed yields are provided or for multi-bin experiments where binned distributions of discriminating variables are provided. It allows the combination of several channels and takes into account statistical and systematic uncertainties, as well as correlations of systematic uncertainties between channels. It has been validated against other software tools and analytical calculations, for several realistic cases.

DNA barcoding of odonates from the Upper Plata basin: Database creation and genetic diversity estimation.

PubMed

Koroiva, Ricardo; Pepinelli, Mateus; Rodrigues, Marciel Elio; Roque, Fabio de Oliveira; Lorenz-Lemke, Aline Pedroso; Kvist, Sebastian

2017-01-01

We present a DNA barcoding study of Neotropical odonates from the Upper Plata basin, Brazil. A total of 38 species were collected in a transition region of "Cerrado" and Atlantic Forest, both regarded as biological hotspots, and 130 cytochrome c oxidase subunit I (COI) barcodes were generated for the collected specimens. The distinct gap between intraspecific (0-2%) and interspecific variation (15% and above) in COI, and resulting separation of Barcode Index Numbers (BIN), allowed for successful identification of specimens in 94% of cases. The 6% fail rate was due to a shared BIN between two separate nominal species. DNA barcoding, based on COI, thus seems to be a reliable and efficient tool for identifying Neotropical odonate specimens down to the species level. These results underscore the utility of DNA barcoding to aid specimen identification in diverse biological hotspots, areas that require urgent action regarding taxonomic surveys and biodiversity conservation.

Experimental Study on the Coupling Mechanism of Early-strength Backfill and Rock

NASA Astrophysics Data System (ADS)

Wang, Mingxu

2017-11-01

In order to study the interaction mechanism between the ore rock and backfill at the early stage, paraffin is chosen as the cementing agent. Based on the damage mechanics and fractal theory, the interaction mechanism between the ore rock and backfill is characterized by the relevant tests on the complex of proportioned ore rock and backfill with resistance strain gauge, crack propagation, microscopic imaging and AE. The experimental results showed that: 1) Through the axial loading test, compared with the early strength of the cemented filling and paraffin mechanical deformation characteristics, the stress and strain curves of the two had a common linear deformation law, while in the early strength of the filling elastic capacity strong, with a certain degree of resilience. 2) The bearing capacity of the backfill was weak, but the deformation ability was strong. During the bearing process, the deformation of the upper load was mainly caused by the ore rock, which leaded to the damage of the rock. 3) The distribution of AE points during the co-carrying of the filling and the ore rock was monitored by the acoustic emission instrument. The damage occurred mainly in the contact zone between the backfill and the ore rock zone. The corresponding AE point distribution also validated the crack happening.

8. VIEW TO NORTH OF INTERIOR OF STAMPMILLING LEVEL; MORTAR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. VIEW TO NORTH OF INTERIOR OF STAMPMILLING LEVEL; MORTAR MOUNT FOR MILL IS IMMEDIATELY BELOW AND TO LEFT OF ORE-HOPPER (UPPER-CENTER). - Steamboat Stampmill, Brush Creek Canyon, Jacksonville, Jackson County, OR

Internal structures and dating of non-sulphide Zn deposits using rock magnetism: insights from the Moroccan High Atlas

NASA Astrophysics Data System (ADS)

Charles, Nicolas; Choulet, Flavien; Sizaret, Stanislas; Chen, Yan; Barbanson, Luc; Ennaciri, Aomar; Badra, Lakhlifi; Branquet, Yannick

2016-01-01

The renewal of interest in Zn-Pb non-sulphide ores has been induced by mineral processing improvement and leads to new exploration and mining projects in the world. Although the mineralogy is often precisely known, and despite several studies linking ore deposition to regional tectonics, absolute dating of non-sulphide stages is rare and structure of ore bodies was largely disregarded. Geochronological data from non-sulphide ores are essential to timely constrain alteration episodes and to insert supergene ore genesis in the climate and tectonic evolution of the metallogenic province. The access to internal organization of ore could reveal post-mineralization episodes related to supergene evolution. Thus, a rock magnetism study combining anisotropy of magnetic susceptibility (AMS) and palaeomagnetism was performed on four non-sulphide deposits from the Moroccan High Atlas. AMS generally shows similar horizontal magnetic fabrics for ores and the clayey and carbonaceous internal sediments filling karstic cavities. The palaeomagnetic directions of ores and internal sediments are compatible, and the calculated poles are consistent with the last 30 Ma of the Africa apparent polar wander path, with an upper age at 0.78 Ma. The proposed three-step scenario is placed within the evolution of the Moroccan High Atlas belt. Deposition of primary sulphides is contemporaneous with opening of the Tethyan and Atlantic oceans. During the Tertiary, intracontinental deformation gave rise to the High Atlas fold-and-thrust belt and to regional uplift. Finally, Zn-Pb sulphides hosted in carbonates experienced oxidation under an arid climate to form karst-related Zn-Pb non-sulphide ores. These promising results pave the way for an efficient method to constrain the internal fabrics and age of Zn supergene deposits.

Manganese Deposits in the Artillery Mountains Region, Mohave County, Arizona

USGS Publications Warehouse

Lasky, S.G.; Webber, B.N.

1944-01-01

The manganese deposits of the Artillery Mountains region lie within an area of about 25 square miles between the Artillery and Rawhide Mountains, on the west side of the Bill Williams River in west-central Arizona. The richest croppings are on the northeast side of this area, among the foothills of the Artillery Mountains. They are 6 to 10 miles from Alamo. The nearest shipping points are Congress, about 50 miles to the east, and Aguila, about 50 miles to the southeast. The principal manganese deposits are part of a sequence of alluvial fan and playa material, probably of early Pliocene age, which were laid down in a fault basin. They are overlain by later Pliocene (?) basalt flows and sediments and by Quaternary basalt and alluvium. The Pliocene (?) rocks are folded into a shallow composite S1ncline ttat occupies the valley between the Artillery and Rawhide Mountains, and the folded rocks along either side of the valley, together with the overlying Quaternary basalt, are broken by faults that have produced a group of horsts, grabens, and step-fault blocks. The manganiferous beds, lie at two zones, 750 to 1,000 feet apart stratigraphically, each of which is locally as much as 300 to 400 feet thick. The main, or upper, zone contains three kinds of ore - sandstone ore, clay ore, and 'hard' ore. The sandstone and clay ores differ from the associated barren sandstone and clay, with which they are interlayered and into which they grade, primarily in containing a variable proportion of amorphous manganese oxides, besides iron oxides and clayey material such as are present in the barren beds. The 'hard' ore is sandstone that has been impregnated with opal and calcite and in which the original amorphous manganese oxides have been largely converted to psilomelane and manganite. The average manganese content of the sandstone and clay ores is between 3 and 4 percent and that of the 'hard' ore is between 6 and 7 percent. The ore contains an average of 3 percent of iron, 0.08 percent of phosphorus, 1.1 percent of barium, and minute quantities of copper, lead, and zinc. Although the manganese content of the sandstone and clay ore may change abruptly from bed to bed, the content within any individual bed changes gradually, and for any large volume of ore both the nanganese and iron content are remarkably uniform. Explorations to June 1941 consisted chiefly of 49 holes diamond-drilled in the upper zone on the Artillery Mountains side of the area. The district is estimated to contain an assured minimum of 200,000,000 tons of material having an average manganese content of 3 to 4 percent. About 20,000,000 tons of this total contains 5 percent or more of manganese, and 2,000,000 to 3,000,000 tons contains 10 percent or more. To what extent these deposits can be utilized is a metallurgical and economic problem. Although the clay and sandstone ores, as well as the 'hard' ore, are present in large tonnages, the 'hard' ore is the only kind that combines minable tonnage with promising grade. About 15,000,000 tons of 'hard' ore is present; about 500,000 tons of this contains 15 percent or more of manganese and averages 17 percent, and somewhat over 2,000,000 tons contains 10 percent or more and averages nearly 13 percent. Except for closer drilling to determine such things as the tonnage, grade, spacing, and form of the richer shoots with greater accuracy before beginning to mine them, further explorations are not recommended, for any new ore found is likely to be similar, both in grade and kind, to that already discovered.

An ore genetic model for the Lubin—Sieroszowice mining district, Poland

NASA Astrophysics Data System (ADS)

Wodzicki, A.; Piestrzyński, A.

1994-04-01

The Lubin-Sieroszowice mining district is a world-class copper-silver, stratabound ore deposit that lies near the Lower-Upper Permian boundary. It transgresses the Werra dolomite, the Kupferschiefer organicrich shale and the Weissliegendes sandstone, which overlie barren Rotliegendes sandstone. On the basis of underground and microscope observations and light stable isotope data, and thermodynamic calculations, a new ore genesis model is proposed whereby ore minerals were deposited in the following stages: Stage 0 was synsedimentary or earliest diagenetic and contains 100s ppm of base metals trapped by clay minerals, and minor sulphides. Stage I was early diagenetic and contains 1000s ppm base metals. It is characterized by bornite and overlying chalcopyrite + pyrite that lie a short distance above the Rotliegendes/Weissliegendes contact. The sulphides were deposited near the interface between an overlying, buffered, reducing fluid (1), largely derived from the Kupferschiefer, and an oxidizing fluid (2) in the Rotliegendes. Stage II is the main ore-forming stage. This stage is late diagenetic, peneconcordant, lies near the Kupferschiefer/Weissliegendes contact, and contains several percent base metals.It is associated with the hematite-bearing Rote Fäule facies and is characterized by vertical zonation. A central chalcocite zone is flanked above and below by bornite and chalcopyrite. Silver occurs with all the above sulphides. Galena and sphalerite occur mainly just above copper zone, whereas pyrite is usually present in the upper part of the copper zone and together with galena and sphalerite. Metals were transported in a copper-rich oxidizing fluid (3), which probably originated deep in the Permian basin, reacted with organic matter in the Kupferschiefer, and mixed with reducing fluid (1) in the Weissliegendes, resulting in the observed mineral zonation. Stage III is late diagenetic, discordant and is represented by massive and dispersed chalcocite ore present on the peripheries and below anhydrite-cemented Weissliegendes sandstone. It resulted from redistribution of earlier copper and silver minerals by descending, reduced, sulphur-rich fluids (4). Stage IV consists of rare polymetallic veins of no economic importance that cut the stratigraphy and are probably related to Alpine tectonism. The richest and thickest ore is in the Weissliegendes, 10-15 km east of the Rote Fäule facies (Fig. 1). It probably occupies structures that trapped fluid (1) which was the main precipitant of metals in the sandstone.

Intraseasonal variability of upper-ocean currents and photosynthetic primary production along the U.S. west coast associated with the Madden-Julian Oscillation

NASA Astrophysics Data System (ADS)

Barrett, B.; Davies, A. R.; Steppe, C. N.; Hackbarth, C.

2017-12-01

In the first part of this study, time-lagged composites of upper-ocean currents from February to May of 1993-2016 were binned by active phase of the leading atmospheric mode of intraseasonal variability, the Madden-Julian Oscillation (MJO). Seven days after the convectively active phase of the MJO enters the tropical Indian Ocean, anomalously strong south-southeastward upper-ocean currents are observed along the majority of U.S. west coast. Seven days after the convectively active phase enters the tropical western Pacific Ocean, upper-ocean current anomalies reverse along the U.S. west coast, with weaker southward flow. A physical pathway to the ocean was found for both of these: (a) tropical MJO convection modulates upper-tropospheric heights and circulation over the Pacific Ocean; (b) those anomalous atmospheric heights adjust the strength and position of the Aleutian Low and Hawaiian High; (c) surface winds change in response to the adjusted atmospheric pressure patterns; and (d) those surface winds project onto upper-ocean currents. In the second part of this study, we investigated if the MJO modulated intraseasonal variability of surface wind forcing and upper-ocean currents projected onto phytoplankton abundance along the U.S. west coast. Following a similar methodology, time-lagged, level 3 chlorophyll-a satellite products (a proxy for photosynthetic primary production) were binned by active MJO phase and analyzed for statistical significance using the Student's t test. Results suggest that intraseasonal variability of biological production along the U.S. west coast may be linked to the MJO, particularly since the time scale of the life cycle of phytoplankton is similar to the time scale of the MJO.

Two types of ore-bearing mafic complexes of the Early Proterozoic East-Scandinavian LIP and their ore potential

NASA Astrophysics Data System (ADS)

Mitrofanov, Felix; Zhirov, Dmitry; Bayanova, Tamara; Korchagin, Alexey; Chaschin, Victor

2015-04-01

Two types of the ore-bearing mafic complexes are allotted in the East-Scandinavian large igneous province (LIP). They differ in geodynamic setting, structure, isotope geochemistry, petrology and mineralogy. The PGE-bearing mafic-ultramafic layered intrusions are associated with the first complex. They have been formed at an initial (pre-rift) stage of LIP. Features of origin of this complex are: 1) large-scale, protracted, and multiple episodes of deep mantle plume or asthenosphere upwelling; 2) the vast non-subduction-type basaltic magma in an intraplate continental setting; 3) low-sulfide Pt-Pd (with Ni, Cu, Au, Co and Rh) mineralization in different geological setting (reef- and contact type etc.); 4) anomalously high concentrations of PGEs in the bulk sulfides, inferred platinum distribution coefficient between silicate and sulfide melts of >100000. Deep mantle magma source is enriched in ore components (fertile source) and lithophile elements. It is reflected in the isotope indicators such as ɛNd(T) from -1 to -3, ISr(87Sr/86Sr) from 0.702 to 0.704, 3Не/4Не = (10 ^-5 ÷ 10 ^-6). Magma and ore sources differ from those of Mid-Ocean Ridge basalts (MORB), subduction-related magma but are similar to EM-I. Ore-bearing mafic complexes formed during a long period of time and by different episodes (2490±10 Ma; 2470±10 Ma; 2450±10 Ma; 2400±10 Ma), and by mixing between the boninitic an anorthositic magmas. It is known about 10 deposits and occurrences in Kola region with total reserves and resources about 2000 tons in palladium equivalent (with an average content ≥2-3 ppm). Intrusions with the rich sulfide Ni-Cu ore (with Co and poor PGE) are associated with the second mafic complex. Ore-controlling mafic-ultramafic intrusions are formed at a final stage of the intracontinental rifting of the Transitional period (2200-1980 Ma). Initial magma is depleted and similar to the MORB in terms of rare earths distribution. Enriched ferropicritic Fe-Ti derivatives of magma generate single volcano-plutonic rock series. For intrusive ore bodies rock differentiation with the formation of syngenetic wehrlite-clinopyroxenite-gabbro- orthoclase gabbro sequence is typical. Upper mantle source of the depleted magma is characterized by the following isotope indicators: ɛNd(T) +0.5 to +4, ISr= 87Sr/86Sr 0.703-0.704. Ore-bearing intrusive bodies are injected in the upper part of the Early Palaeoproterozoic volcano-sedimentary cross-section. Ores are located in the basement of intrusions and in the redeposited veined bodies, including offset setting. Numerous Ni-Cu deposits with total reserves and resources of several million tons of Nickel equivalent (with an average grade ≥ 0,3%) have been explored, and some of them now is mining. As a result of our research, the complex of indicators and criteria is suggested for predicting the occurrence, for regional exploration target selection and for regional resource evaluation of PGE and base metals. The studies are supported by the Russian Foundation for Basic Research (project nos. 13-05-12055).

DNA barcoding of odonates from the Upper Plata basin: Database creation and genetic diversity estimation

PubMed Central

Pepinelli, Mateus; Rodrigues, Marciel Elio; Roque, Fabio de Oliveira; Lorenz-Lemke, Aline Pedroso; Kvist, Sebastian

2017-01-01

We present a DNA barcoding study of Neotropical odonates from the Upper Plata basin, Brazil. A total of 38 species were collected in a transition region of “Cerrado” and Atlantic Forest, both regarded as biological hotspots, and 130 cytochrome c oxidase subunit I (COI) barcodes were generated for the collected specimens. The distinct gap between intraspecific (0–2%) and interspecific variation (15% and above) in COI, and resulting separation of Barcode Index Numbers (BIN), allowed for successful identification of specimens in 94% of cases. The 6% fail rate was due to a shared BIN between two separate nominal species. DNA barcoding, based on COI, thus seems to be a reliable and efficient tool for identifying Neotropical odonate specimens down to the species level. These results underscore the utility of DNA barcoding to aid specimen identification in diverse biological hotspots, areas that require urgent action regarding taxonomic surveys and biodiversity conservation. PMID:28763495

Fluid inclusions and biomarkers in the Upper Mississippi Valley zinc-lead district; implications for the fluid-flow and thermal history of the Illinois Basin

USGS Publications Warehouse

Rowan, E. Lanier; Goldhaber, Martin B.

1996-01-01

The Upper Mississippi Valley zinc-lead district is hosted by Ordovician carbonate rocks at the northern margin of the Illinois Basin. Fluid inclusion temperature measurements on Early Permian sphalerite ore from the district are predominantly between 90?C and I50?C. These temperatures are greater than can be explained by their reconstructed burial depth, which was a maximum of approximately 1 km at the time of mineralization. In contrast to the temperatures of mineral formation derived from fluid inclusions, biomarker maturities in the Upper Mississippi Valley district give an estimate of total thermal exposure integrated over time. Temperatures from fluid inclusions trapped during ore genesis with biomarker maturities were combined to construct an estimate of the district's overall thermal history and, by inference, the late Paleozoic thermal and hydrologic history of the Illinois Basin. Circulation of groundwater through regional aquifers, given sufficient flow rates, can redistribute heat from deep in a sedimentary basin to its shallower margins. Evidence for regional-scale circulation of fluids is provided by paleomagnetic studies, regionally correlated zoned dolomite, fluid inclusions, and thermal maturity of organic matter. Evidence for igneous acti vity contemporaneous with mineralization in the vicinity of the Upper Mississippi Valley district is absent. Regional fluid and heat circulation is the most likely explanation for the elevated fluid inclusion temperatures (relative to maximum estimated burial depth) in the Upper Mississippi Valley district. One plausible driving mechanism and flow path for the ore-forming fluids is groundwater recharge in the late Paleozoic Appalachian-Ouachita mountain belt and northward flow through the Reelfoot rift and the proto- Illinois Basin to the Upper Mississippi Valley district. Warm fluid flowing laterally through Cambrian and Ordovician aquifers would then move vertically upward through the fractures that control sphalerite mineralization in the Upper Mississippi Valley district. Biomarker reactant-product measurements on rock extracts from the Upper Mississippi Valley district define a relatively low level ofthermal maturity for the district, 0.353 for sterane and 0.577 for hopane. Recently published kinetic constants permit a time-temperature relationship to be determined from these biomarker maturities. Numerical calculations were made to simulate fluid heat flow through the fracture-controlled ore zones of the Thompson-Temperly mine and heat transfer to the adjacent rocks where biomarker samples were collected. Calculations that combine the fluid inclusion temperatures and the biomarker constraints on thermal maturity indicate that the time interval during which mineralizing fluids circulated through the Upper Mississippi Valley district is on the order of 200,000 years. Fluid inclusion measurements and thermal maturities from biomarkers in the district reflect the duration of peak temperatures resulting from regional fluid circulation. On the basis of thermal considerations, the timing of fluorite mineralization in southern Illinois, and the northward-decreasing pattern of fluorine enrichment in sediments, we hypothesize that the principal flow direction was northward through the Cambrian and Ordovician aquifers of the Illinois Basin. A basin-scale flow system would result in mass transport (hydrocarbon migration, transport of metals in solution) and energy (heat) transport, which would in turn drive chemical reactions (for example, maturation of organic matter, mineralization, diagenetic reactions) within the Illinois Basin and at its margins.

OVERVIEW OF STAMP MILL SITE,LOOKING SOUTHWEST. THE LOWER TRAM TERMINAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERVIEW OF STAMP MILL SITE,LOOKING SOUTHWEST. THE LOWER TRAM TERMINAL IS OUT OF FRAME, JUST TO THE RIGHT. WATER TANK, LOADING PLATFORM, AND TRAM TRESTLE LEADING UP TO THE TRAM TERMINAL ARE AT RIGHT. THE STRUCTURE AT EXTREME RIGHT BELOW THE TRESTLE, ARE REMAINS OF A SECONDARY ORE BIN, WITH BALL MILL FOUNDATIONS AND WOOD DEBRIS JUST BELOW ON THE SECOND LEVEL. AT CENTER IS A BOILER AND THE FRAME WORK OF A FILTER PRESS. THE SMALL STRUCTURE AT CENTER LEFT IS AN INTERPRETIVE SIGN PLACED BY THE PARK SERVICE. AT LOWER LEFT, THIRD LEVEL OF THE MILL, ARE THE REMAINS OF A BLACKSMITH'S FORGE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

The composition of fluid inclusions in ore and gangue minerals from the Silesian-Cracow Mississippi Valley-type Zn-Pb deposits Poland: Genetic and environmental implications

USGS Publications Warehouse

Viets, J.G.; Hofstra, A.H.; Emsbo, P.; Kozlowski, A.

1996-01-01

The composition of fluids extracted from ore and gangue sulfide minerals that span most of the paragenesis of the Silesian-Cracow district was determined using a newly developed ion chromatographic (IC) technique. Ionic species determined were Na+, NH+4, Ca2+, Mg2+, K+, Rb+, Sr2+, Ba2+, Cl-, Br-, F-, I-, PO3-4, CO2-3, HS-, S2O2-3, SO2-4, NO-3, and acetate. Mineral samples included six from the Pomorzany mine and one from the Trzebionka mine which are hosted in the Triassic Muschelkalk Formation, and two samples of drill core from mineralized Upper Devonian strata. Nine paragenetically identifiable sulfide minerals occur throughout the Silesian-Cracow district. These include from earliest to latest: early iron sulfides, granular sphalerite, early galena, light-banded sphalerite, galena, dark-banded sphalerite, iron sulfides, late dark-banded sphalerite with late galena, and late iron sulfides. Seven of the minerals were sampled for fluid inclusion analysis in this study. Only the early iron sulfides and the last galena stage were not sampled. Although the number of analyses are limited to nine samples and two replicates and there is uncertainty about the characteristics of the fluid inclusions analyzed, the data show clear temporal trends in the composition of the fluids that deposited these minerals. Fluid inclusions in minerals deposited later in the paragenesis have significantly more K+, Br-, NH+4, and acetate but less Sr2+ than those deposited earlier in the paragenesis. The later minerals are also characterized by isotopically lighter sulfur and significantly more Tl and As in the solid minerals. The change in ore-fluid chemistry is interpreted to reflect a major change in the hydrologic regime of the district. Apparently, the migrational paths of ore fluids from the Upper Silesian basin changed during ore deposition and the fluids which deposited early minerals reacted with aquifers with very different geochemical characteristics than those that deposited late minerals. The early fluids may have reacted primarily with Devonian and Lower Carboniferous carbonate aquifers deeper in the basin, whereas the later fluids appear to have had extensive contact with organic-rich rocks, probably the shallower Middle and Upper Carboniferous flysch associated with coal measures. High concentrations of toxic Tl and As occur in the readily oxidized marcasite and pyrite minerals deposited by the later fluids. In general, the geochemistry of both the early and late fluids may be explained by an evaporite related origin or by water-rock modification of a saline basinal brine. When compared to the composition of fluid inclusions in Mississippi Valley-type (MVT) ore minerals from the Ozark region of the United States, fluid inclusions in minerals from Silesian-Cracow are fundamentally different, containing more Ca2+, Mg2+, NH+4, Br-, Sr2+ and acetate in all mineral stages with significantly more K+ in later stage minerals. The differences in ore fluid chemistry between the two regions are consistent with the lithologic differences of the respective basins thought to be the source of the mineralizing brines.

Contrasting hydrological processes of meteoric water incursion during magmatic-hydrothermal ore deposition: An oxygen isotope study by ion microprobe

NASA Astrophysics Data System (ADS)

Fekete, Szandra; Weis, Philipp; Driesner, Thomas; Bouvier, Anne-Sophie; Baumgartner, Lukas; Heinrich, Christoph A.

2016-10-01

Meteoric water convection has long been recognized as an efficient means to cool magmatic intrusions in the Earth's upper crust. This interplay between magmatic and hydrothermal activity thus exerts a primary control on the structure and evolution of volcanic, geothermal and ore-forming systems. Incursion of meteoric water into magmatic-hydrothermal systems has been linked to tin ore deposition in granitic plutons. In contrast, evidence from porphyry copper ore deposits suggests that crystallizing subvolcanic magma bodies are only affected by meteoric water incursion in peripheral zones and during late post-ore stages. We apply high-resolution secondary ion mass spectrometry (SIMS) to analyze oxygen isotope ratios of individual growth zones in vein quartz crystals, imaged by cathodo-luminescence microscopy (SEM-CL). Existing microthermometric information from fluid inclusions enables calculation of the oxygen isotope composition of the fluid from which the quartz precipitated, constraining the relative timing of meteoric water input into these two different settings. Our results confirm that incursion of meteoric water directly contributes to cooling of shallow granitic plutons and plays a key role in concurrent tin mineralization. By contrast, data from two porphyry copper deposits suggest that downward circulating meteoric water is counteracted by up-flowing hot magmatic fluids. Our data show that porphyry copper ore deposition occurs close to a magmatic-meteoric water interface, rather than in a purely magmatic fluid plume, confirming recent hydrological modeling. On a larger scale, the expulsion of magmatic fluids against the meteoric water interface can shield plutons from rapid convective cooling, which may aid the build-up of large magma chambers required for porphyry copper ore formation.

Uranium resources in the Silver Reef (Harrisburg) district, Washington County, Utah

USGS Publications Warehouse

Stugard, Frederick

1951-01-01

The Silver Reef district is near Leeds, about 16 miles north of St. George, Utah. The major structural feature of the district is the Virgin anticline, a fold extending southwestward toward St. George. The anticline has been breached by erosion, and sandstone hogbacks or 'reefs' are carved from the Shinarump conglomerate mud sandstone members of the Chinle formation, both of Triassic age. Thirteen occurrences of uranium-vanadium minerals, all within the Tecumseh sandstone, which is the upper part of the Silver Reef sandstone member of the Chinle formation, have been examined over an area about 1.75 miles wide and 3 miles long. Two shipments of uranium-vanadium ore have been produced from the Chloride Chief and Silver Point claims. Samples from the deposits contain as much as 0.94 percent U3O8. The ore contains several times as much vanadium oxide as uranium, some copper, and traces of silver. It occurs in thinly bedded cross-bedded shales and sandstones within the fluviatile Tecumseh sandstone member of the Chinle formation. The ore beds are lenticular and are localized 2 near the base, center, and top of this sandstone member. The uranium-vanadium ore contains several yellow and green minerals not yet identified; the occurrences are similar to, but not associated with, the cerargyrite ore that made the district famous from 1879 to 1909.

The Gas Hills uranium district and some probable controls for ore deposition

USGS Publications Warehouse

Zeller, Howard Davis

1957-01-01

Uranium deposits occur in the upper coarse-grained facies of the Wind River formation of Eocene age in the Gas Hills district of the southern part of the Wind River Basin. Some of the principal deposits lie below the water table in the unoxidized zone and consist of uraninite and coffinite occurring as interstitial fillings in irregular blanket-like bodies. In the near-surface deposits that lie above the water table, the common yellow uranium minerals consist of uranium phosphates, silicates, and hydrous oxides. The black unoxidized uraninite -coffinite ores show enrichment of molybdenum, arsenic, and selenium when compared to the barren sandstone. Probable geologic controls for ore deposits include: 1) permeable sediments that allowed passage of ore-bearing solutions; 2) numerous faults that acted as impermeable barriers impounding the ore -bearing solutions; 3) locally abundant pyrite, carbonaceous material, and natuial gas containing hydrogen sulfide that might provide a favorable environment for precipitation of uranium. Field and laboratory evidence indicate that the uranium deposits in the Gas Hills district are very young and related to the post-Miocene to Pleistocene regional tilting to the south associated with the collapse of the Granite Mountains fault block. This may have stopped or reversed ground water movement from a northward (basinward) direction and alkaline ground water rich in carbonate could have carried the uranium into the favorable environment that induced precipitation.

Compositional variation of glauconites in Upper Cretaceous-Paleogene sedimentary iron-ore deposits in South-eastern Western Siberia

NASA Astrophysics Data System (ADS)

Rudmin, Maxim; Banerjee, Santanu; Mazurov, Aleksey

2017-06-01

Glauconite occurs either as unaltered greenish or as altered brownish variety in Upper Cretaceous-Palaeocene sediments in the southeastern corner of Western Siberia. Studied section within the Bakchar iron-ore deposit includes Ipatovo, Slavgorod, Gan'kino and Lyulinvor formations, which are represented by sandstones, siltstones, claystones and oolitic ironstones of coastal-marine facies. The origin of unaltered glauconite is explained by the ;verdissement theory;. Transgressions during Lower Coniacian, Santonian and Campanian favored the formation of unaltered glauconites in dysoxic to anoxic conditions. Subaerial exposure of glauconite resulted in leaching of potassium, oxidation of iron and formation of iron hydroxides in Upper Coniacian, Maastrichtian and Palaeocene. Glauconite ultimately converts to leptochlorite and hydrogoethite by this alteration. Abundant microscopic gold inclusions, besides sulphides, sulphates, oxides and silicates characterize this glauconite. Mineral inclusions include precious, rare metals and non-ferrous metals. The concentration of gold in glauconite may be as high as 42.9 ppb. Abundant inclusions of various compositions in glauconites indicate enrichment of marine sediments in precious and non-precious metals. While major element composition of glauconites is affected by subaerial exposure, the broadly similar micro-inclusions in both altered and unaltered varieties are possibly related to the comparatively immobile nature of REE and trace elements.

Behavior of uranium under conditions of interaction of rocks and ores with subsurface water

NASA Astrophysics Data System (ADS)

Omel'Yanenko, B. I.; Petrov, V. A.; Poluektov, V. V.

2007-10-01

The behavior of uranium during interaction of subsurface water with crystalline rocks and uranium ores is considered in connection with the problem of safe underground insulation of spent nuclear fuel (SNF). Since subsurface water interacts with crystalline rocks formed at a high temperature, the mineral composition of these rocks and uranium species therein are thermodynamically unstable. Therefore, reactions directed toward the establishment of equilibrium proceed in the water-rock system. At great depths that are characterized by hindered water exchange, where subsurface water acquires near-neutral and reducing properties, the interaction is extremely sluggish and is expressed in the formation of micro- and nanoparticles of secondary minerals. Under such conditions, the slow diffusion redistribution of uranium with enrichment in absorbed forms relative to all other uranium species is realized as well. The products of secondary alteration of Fe- and Ti-bearing minerals serve as the main sorbents of uranium. The rate of alteration of minerals and conversion of uranium species into absorbed forms is slow, and the results of these processes are insignificant, so that the rocks and uranium species therein may be regarded as unaltered. Under reducing conditions, subsurface water is always saturated with uranium. Whether water interacts with rock or uranium ore, the equilibrium uranium concentration in water is only ≤10-8 mol/l. Uraninite ore under such conditions always remains stable irrespective of its age. The stability conditions of uranium ore are quite suitable for safe insulation of SNF, which consists of 95% uraninite (UO2) and is a confinement matrix for all other radionuclides. The disposal of SNF in massifs of crystalline rocks at depths below 500 m, where reducing conditions are predominant, is a reliable guarantee of high SNF stability. Under oxidizing conditions of the upper hydrodynamic zone, the rate of interaction of rocks with subsurface water increases by orders of magnitude and subsurface water is commonly undersaturated with uranium. Uranium absorbed by secondary minerals, particularly by iron hydroxides and leucoxene, is its single stable species under oxidizing conditions. The impact of oxygen-bearing water leads to destruction of uranium ore. This process is realized simultaneously at different hypsometric levels even if the permeability of the medium is variable in both the lateral and vertical directions. As a result, intervals containing uranyl minerals and relics of primary uranium ore are combined in ore-bearing zones with intervals of completely dissolved uranium minerals. A wide halo of elevated uranium contents caused by sorption is always retained at the location of uranium ore entirely destroyed by weathering. Uranium ore commonly finds itself in the aeration zone due to technogenic subsidence of the groundwater table caused by open-pit mining or pumping out of water from underground mines. The capillary and film waters that interact with rocks and ores in this zone are supplemented by free water filtering along fractures when rain falls or snow is thawing. The interaction of uranium ore with capillary water results in oxidation of uraninite, accompanied by loosening of the mineral surface, formation of microfractures, and an increase in solubility with enrichment of capillary water in uranium up to 10-4 mol/l. Secondary U(VI) minerals, first of all, uranyl hydroxides and silicates, replace uraninite, and uranium undergoes local diffusion redistribution with its sorption by secondary minerals of host rocks. The influx of free water facilitates the complete dissolution of primary and secondary uranium minerals, the removal of uranium at the sites of groundwater discharge, and its redeposition under reducing conditions at a greater depth. It is evident that the conditions of the upper hydrodynamic zone and the aeration zone are unfit for long-term insulation of SNF and high-level wastes because, after the failure of containers, the leakage of radionuclides into the environment becomes inevitable.

Chromatography resin support

DOEpatents

Dobos, James G.

2002-01-01

An apparatus and method of using an improved chromatography resin support is disclosed. The chromatography support platform is provided by a stainless steel hollow cylinder adapted for being inserted into a chromatography column. An exterior wall of the stainless steel cylinder defines a groove for carrying therein an "O"-ring. The upper surface of the stainless steel column is covered by a fine stainless steel mesh welded to the edges of the stainless steel cylinder. When placed upon a receiving ledge defined within a chromatography column, the "O"-ring provides a fluid tight seal with the inner edge wall of the chromatography cylinder. The stainless steel mesh supports the chromatography matrix and provides a back flushable support which is economical and simple to construct.

Sedimentary conditions of Upper Permian volcano-clastic rocks of Ayan-Yrahskiy anticlinorium (Verhoyansk-Kolyma orogen)

NASA Astrophysics Data System (ADS)

Astakhova, Anna; Khardikov, Aleksandr

2013-04-01

Sedimentation conditions of upper Permian volcano-clastic rocks of Ayan-Yurakhsky anticlinorium are the reason of discussions between researchers. It is important to correctly solve this problem. Investigation allows us to conclude that upper Permian sediments was formed due to high rate deltaic sedimentation on shelf and continental slope of epicontinental sea basin. More than 45 outcrops of upper Permian sediments were described within Ayan-Yurakhsky anticlinorium. Termochemical and X-ray phase, lithological facies, stadial, paleogeographic and others were applied. Investigation allows to classify following types: tuffs, tuffites of andesites, andesi-dacites, sandstone tuffs, siltstone tuffs and claystone tuffs. Two facies were deliniated in the research area: 1) delta channel facies 2) epicontinental sea shelf edge and continental slope. Delta channel facies are located on the south-west part of Aian-Yrahskiy anticlinorium. It is composed of silty packsand and psammitic tuff-siltstone alternation and gravel-psammitic andesi-dacitic tuffute and tuff-breccia bands. Sediments have cross-bedding, through cross-bedding, curvilinear lamination structures. Facies occurred during high rate deltaic sedimentation on the shelf of epicontinental sea. Epicontinental sea shelf edge and continental slope facies are located on the south-west part. Sediments are represented by large thickness tuff-siltstone with tuff-sandstone, tuff-madstone, tuff, tuffite bands and lenses. Large number of submarine landslides sediments provide evidence that there was high angle sea floore environment. 30-50 m diametr eruption centers were described by authors during geological traverses. They are located in Kulu river basin. Their locations are limited by deep-seated pre-ore fault which extended along Ayan-Yurakhsky anticlinorium. U-Pb SHRIMP method showed that the average age of circons, taken from eruption centers, is Permian (256,3±3,7 ma). This fact confirms our emphasis that eruption centers were the centre of underwater effusive explosions which had been occurred in late Permian time. Gold ore deposits mainly localized in the south of Ayan-Yurakhsky anticlinorium and associated with upper Permian deltaic facies sediments. Taking into account lithological facies feature and volcanoclastic origin of sediments it is reasonable to suggest expelled-catagenesis model of gold mineralization. Gold was entered in sedimentary basin with piroclastic material. During catagenesis stage gold migrated from complex of shelf edge and continental slope to fan delta front complex in conjunction with expelled water. The emplacement of ore gold deposits related with upper Permian sediments can be successfully predicted, using this model and associated techniques.

Geology of the Göçükdibi Cu-Pb-Zn Mineralization, Gökçedoǧan, Çorum (Turkey): Preliminary Findings on Its Formation

NASA Astrophysics Data System (ADS)

Yalçin, Cihan; Hanilçi, Nurullah; Kumral, Mustafa; Abdelnasser, Amr

2016-04-01

Göçükdibi Cu-Pb-Zn mineralization is located 3 km north west of Gökçedoǧan village where is 30 km east of the Kargı, Çorum. The geology of the mineralization area is represented by Mesozoic and Upper Pliocene lithostratigraphic units in different origin. These units with respect to their structural locations have identified as autochthonous and allachtonous. The autochthonous units which are the basement of the region are represented by Bekirli Metamorphites (Triassic-Liassic) and Beşpınar formation (Upper Cretaceous-Lower Eocene) which overlies the Bekirli Metamorphites as angular discordance. The allachtonous units are represented by Saraycık formation belongs to Kargı Ophioltic Melange, and located on the autochthonous units as tectonically. These allocthonous units are the product of the Neotethyan Ocean. The autochthonous and allachtonous units are overlaid by Upper Pliocene Ilgaz Formation and Plio-Quaternary stream sediments. The Cu-Pb-Zn mineralization is located in northwest of the Gökçedoǧan village within the Bekirli Metamorphites. The ore zone has N80E direction, 5 m wide and 120 m in length. The mineralizations which follow NE-SW trending structural line occurred as alternation with quartz-chlorite schists of the Bekirli Metamorphites. The mineralization is generally concordant to the foliation of schist's and also occurred as disseminated in the wall rocks. The ore paragenesis comprises with pyrite, chalcopyrite, sphalerite and galenit as the main sulphide minerals, and the malachite, azurite and limonite as the production of the oxidation. Preliminary data such as relationship between the ore and host rock, inner-structure of the ore and indicate that the Gökçedoǧan Cu-Pb-Zn mineralization was likely to have originated syngenetic. In addition, the geochemical behaviour of rare earth elements (REE) of the altered and mineralized samples collected from the alteration zone show that light REE enrichment with fair depletion of heavy REE during the alteration processes with positive Eu anomalies. As well as there is a positive correlation between K2O index and LREE that reveal the addition of K and La and the sericitization is the main alteration associated with the studied deposit. Key Words: Cu-Pb-Zn mineralization, Syngenetic, Bekirli Metamorphites, Gökçedoǧan.

A mineralogical perspective on the recovery of platinum group elements from Merensky Reef and UG2 at the Two Rivers mine on the Eastern limb of the Bushveld Complex in South Africa

NASA Astrophysics Data System (ADS)

Rose, Derek H.; Viljoen, K. S.; Mulaba-Bafubiandi, Antoine

2018-06-01

Published studies dealing with the process mineralogy of Pt mines on the Bushveld Complex is generally limited to the Western Bushveld. The recognition by mine management that another resource, in addition to the Upper Group 2 (UG2) reef currently being mined at the Two Rivers platinum mine (TRP), is urgently required in order to extend the life of mine, presented an opportunity to conduct such a study on the Eastern Limb of the Bushveld Complex. A process mineralogical investigation was undertaken on ore from the Merensky Reef (MR) and the UG2 at TRP. This was conducted on a suite of geological samples (channel samples) collected from the underground workings, as well as metallurgical samples obtained from the rougher circuits at the concentrator plant during the processing of MR and UG2 ore. The geological and metallurgical samples were analysed for bulk composition and quantitative mineralogy, while the geological samples were also subjected to laboratory-scale milling and flotation tests. This study shows that, although mineralogically distinct, the MR and UG2 behave similarly in terms of metallurgical performance. This holds promise for the proposed blending of MR and UG2 ores at TRP. An evaluation of the bulk rock (ore) Pt/Pd ratio as a possible indicator of the level of hydrothermal alteration of the ore, demonstrates that this may be of use in predicting recovery plant performance.

Analytical Results for 42 Fluvial Tailings Cores and 7 Stream Sediment Samples from High Ore Creek, Northern Jefferson County, Montana

USGS Publications Warehouse

Fey, David L.; Church, Stan E.

1998-01-01

Metal-mining related wastes in the Boulder River basin study area in northern Jefferson County, Montana have been implicated in their detrimental effects on water quality with regard to acid-generation and toxic-metal solubility. Sediments, fluvial tailings and water from High Ore Creek have been identified as significant contributors to water quality degradation of the Boulder River below Basin, Montana. A study of 42 fluvial tailings cores and 7 stream sediments from High Ore Creek was undertaken to determine the concentrations of environmentally sensitive elements (i.e. Ag, As, Cd, Cu, Pb, Zn) present in these materials, and the mineral phases containing those elements. Two sites of fluvial deposition of mine-waste contaminated sediment on upper High Ore Creek were sampled using a one-inch soil probe. Forty-two core samples were taken producing 247 subsamples. The samples were analyzed by ICP-AES (inductively coupled-plasma atomic emission spectroscopy) using a total mixed-acid digestion. Results of the core analyses show that the elements described above are present at very high concentrations (to 22,000 ppm As, to 460 ppm Ag, to 900 ppm Cd, 4,300 ppm Cu, 46,000ppm Pb, and 50,000 ppm Zn). Seven stream-sediment samples were also analyzed by ICP-AES for total element content and for leachable element content. Results show that the sediment of High Ore Creek has elevated levels of ore-related metals throughout its length, down to the confluence with the Boulder River, and that the metals are, to a significant degree, contained in the leachable phase, namely the hydrous amorphous iron- and manganese-hydroxide coatings on detrital sediment particles.

The Darzi-Vali bauxite deposit, West-Azarbaidjan Province, Iran: Critical metals distribution and parental affinities

NASA Astrophysics Data System (ADS)

Khosravi, Maryam; Abedini, Ali; Alipour, Samad; Mongelli, Giovanni

2017-05-01

The Darzi-Vali bauxite deposit, located 20 km east of Bukan, in northwestern Iran, occurs as discontinuous layers and lenses within the Upper Permian carbonate rocks of the Ruteh Formation. These layers extend laterally for over ∼1 km and vary in thickness ranging from 2 to 17 m. We studied the chemical variations in a selected stratigraphic section throughout the deposit, focusing in particular on numbers of selected special metals that make the deposit of potential economic importance. The critical elements Co, Ga, Nb, Ta, LREEs, and HREEs, along with transition metal Ni, are variously depleted throughout the deposit with respect to Ti, which is assumed to be a less mobile element. Among the critical elements, Cr has only demonstrated conservative behavior. Factor analysis suggests that the factors controlling the distribution of LREEs and HREEs in the ore, which most likely depend on the local composition of groundwater during weathering, are different from those controlling the distribution of other critical elements. Further, the Darzi-Vali ore has ΣREE contents (773 ppm) much higher with respect to other deposits located in NW of Iran, making this deposit worthy of further investigations. As for parental affinity, the Eu anomalies show negligible fluctuations (0.82-0.94) all along the deposit confirming that bauxitization does not affect the effectiveness of this provenance proxy. The average Eu/Eu* value (0.89) of the ore is relatively far afield from that of the average carbonate bedrock (1.3) and close to that of the average mafic protolith (0.94), and similar results are also obtained using the Sm/Nd and Tb/Tb* proxies. Bivariate plots of Eu anomaly versus Sm/Nd and Tb anomalies further support the idea that mafic rocks are probably related to the volcanic activities. These volcanic activities affected the Iranian platform during the Upper Permian as proposed for other bauxite deposits in northwestern Iran. These mafic rocks were the probable precursor of the Darzi-Vali bauxite ore.

Technogenic magnetic particles in soils as evidence of historical mining and smelting activity: A case of the Brynica River Valley, Poland.

PubMed

Magiera, Tadeusz; Mendakiewicz, Maria; Szuszkiewicz, Marcin; Jabłońska, Mariola; Chróst, Leszek

2016-10-01

In the area of Brynica River basin (Upper Silesia, southern Poland) the exploitation and smelting of iron, silver and lead ores was historically documented since early Middle Ages. First investigations showed that metallurgy industry had a large impact from 9th century (AD) until the Second World War. The aim of the study was to use magnetic prospection to detect traces of past mining and ore smelting in Brynica River Valley located in Upper Silesia (southern Poland). The field screening was performed by measurement magnetic susceptibility (κ) on surface and in vertical profiles and was supported locally by gradiometric measurements. Vertical distribution of magnetic susceptibility values was closely associated with the type of soil use. Historical technogenic magnetic particles resulting from exploitation, processing, and smelting of iron, silver, and lead ores were accumulated in the soil layer at the depth 10 to 25cm. They were represented by sharp-edged particles of slag, coke, as well as various mineralogical forms of iron minerals and aggregates composed of carbon particles, aluminosilicate glass, and single particles of metallic iron. The additional geochemical study in adjacent peat bog supported by radiocarbon dating was also performed. The application of integrated geochemical-magnetic methods to reconstruct the historical accumulation of pollutants in the studied peat bog was effective. The magnetic peak, which was pointed out by magnetic analyses, is consistent with the presence of charcoal and pollution from heavy metals, such as Ag, Cd, Cu, Fe, Pb, or Sn. The results of this work will be helpful for the further study of human's impact on the environment related to the historical and even pre-historical ore exploitation and smelting and also used for better targeting the archeological excavations on such areas. Copyright © 2016 Elsevier B.V. All rights reserved.

Platinum potential of mafic-ultramafic massifs in the western part of the Dambuka ore district (Upper Amur Region, Russia)

NASA Astrophysics Data System (ADS)

Melnikov, A. V.; Stepanov, V. A.; Moiseenko, V. G.

2016-02-01

New data on the Pt potential of mafic-ultramafic massifs of the Khani-Maya, Uldegit, and Dzhalta complexes in the western part of the Dambuka ore district are discussed. The Khani-Maya Complex is represented by metamorphosed gabbro, gabbronorites, gabbro anorthosites, subordinate pyroxenites, hornblendites, and peridotites. The Uldegit Complex is composed of pyroxenites, hornblendites, gabbro, gabbronorites, norites, troctolites, peridotites, dunites, actinolite-tremolites, serpentinites, anthophyllites, and tremolite-plagioclase rocks. The Dzhalta Complex is formed of peridotites, gabbro, eclogitized gabbro, hornblendites, cortlandites, and pyroxenites. All these complexes differ from each other by the concentrations of Ni, Cu, Co, Au, and platinoids depending on the composition of the constituting rocks and the presence of sulfide minerals.

Use of the high-resolution satellite images for detection of fractures related to the ore deposits

NASA Astrophysics Data System (ADS)

Cruz-Mondaca, M.; Soto-Pinto, C. A.; Arellano-Baeza, A. A.

2012-12-01

The Aster and GeoEye satellite high-resolution images were used to detect the structures related to the fracturing of the upper crust in the North of Chile. In particular, lineament analysis has been applied to detect the presence of epithermal fluids of low sulfurization associated with the Paleozoic ore deposits. These results have been compared with the location of the minerals altered by the presence of geothermal fluids detected using the spectral libraries. Later, the presence of fractures has been corroborated during recognition of fractures in situ and the geochemical analysis of samples of minerals altered by the presence of fluids. It was shown that the results obtained are relevant for the gold vein detection.

Geochemistry of vanadium in an epigenetic, sandstone-hosted vanadium- uranium deposit, Henry Basin, Utah

USGS Publications Warehouse

Wanty, R.B.; Goldhaber, M.B.; Northrop, H.R.

1990-01-01

The epigenetic Tony M vanadium-uranium orebody in south-central Utah is hosted in fluvial sandstones of the Morrison Formation (Upper Jurassic). Measurements of the relative amounts of V+3 and V +4 in ore minerals show that V+3 is more abundant. Thermodynamic calculations show that vanadium was more likely transported to the site of mineralization as V+4. The ore formed as V+4 was reduced by hydrogen sulfide, followed by hydrolysis and precipitation of V+3 in oxide minerals or chlorite. Uranium was transported as uranyl ion (U+6), or some complex thereof, and reduced by hydrogen sulfide, forming coffinite. Detrital organic matter in the rocks served as the carbon source for sulfate-reducing bacteria. Vanadium most likely was derived from the dissolution of iron-titanium oxides. Uranium probably was derived from the overlying Brushy Basin Member of the Morrison Formation. Previous studies have shown that the ore formed at the density-stratified interface between a basinal brine and dilute meteoric water. The mineralization processes described above occurred within the mixing zone between these two fluids. -from Authors

Mineralogy and trace element geochemistry of the Co- and Cu-bearing sulfides from the Shilu Fe-Co-Cu ore district in Hainan Province of South China

NASA Astrophysics Data System (ADS)

Wang, Zhilin; Xu, Deru; Zhang, Zhaochong; Zou, Fenghui; Wang, Li; Yu, Liangliang; Hu, Mingyue

2015-12-01

Hosted within the metamorphosed, neritic siliciclastic rocks and sedimentary carbonates of the Proterozoic Shilu Group, the Shilu Fe-Co-Cu ore district in Hainan Province of South China comprises the upper Fe- and the lower Co-Cu ore layers. Combined with the field observation, the mineralogical and geochemical studies of sulfides using electron microprobe and laser ablation ICP-MS analyses recognized three types of Co-Cu ores. Type I is represented by massive ores and mainly comprises the first generation of pyrite (PyI) which occurred either as recrystallized, subhedral to euhedral microcrystal aggregates (PyIa) or as elongated, fine-grained euhedral grains (PyIb) with an orientated alignment parallel to S1 foliation. Type II is banded, disseminated and brecciated ores, and composed of the second generation of pyrite (PyII) which displays internal rhythmic growth zoning, the first generations of chalcopyrite (CcpI) and pyrrhotite (PoI), and associated Co-(Ni)-(As)-sulfide minerals. Type III occurring as veins or veinlets mainly consists of the third generation of pyrite (PyIII) and the second generations of chalcopyrite (CcpII) and pyrrhotite (PoII), of which PyIII appears as subhedral to euhedrall grains or as rims of composite pyrite. The moderate Co and As, and high Ni contents as well as the low Co/Ni ratios (∼2-5) in PyI indicate a sedimentary-metamorphic origin for Type I ores. The higher Co, Ni and As concentrations in PyIb relative to PyIa likely was related to an inhomogeneous deformation-metamorphism. The highest Co (av. 51,195 ppm) in PyII and Ni (av. 3374 ppm) in PoI most likely were linked to the preferred incorporation of Co into pyrite and Ni into pyrrhotite. Combined with the high Ag concentrations in CcpI (av. 266 ppm) and PyII (av. 13.32 ppm), the high Co/Ni ratios in PyII (av. 1241) suggest the derivation of Type II ores from a Co-Cu-Ni-Ag-rich hydrothermal fluid. Further, up to 9 wt.% Co concentrations in PyII show a temperature condition of 310-400 °C. In contrast, the depletion of trace elements in CcpII and PyIII, and the lower Co/Ni ratios (av. 46) in PyIII suggest a Co-poor but Cu-bearing hydrothermal fluid for origin of Type III ores. The complex texture and chemical composition of sulfides combined with previous work confirm a four-stage metallogenesis for the Shilu Co-Cu ores. From early to late, these include: (1) the ca. 1075-880 Ma deposition of the primary Co-Cu ore source beds which most likely were derived from submarine, metalliferous hydrothermal fluids, (2) the syn-structural metamorphism which led to Type I ores due to the South China Caledonian Orogeny, (3) the first stage of hydrothermalism which produced Type II ores and most likely was associated with Indosinian magmatism, and (4) the second stage of hydrothermalism which yielded Type III ores and likely was related to Yanshanian magmatism. The first stage of hydrothermalism was considered to be significant for the Co-Cu enrichment. The Shilu Co-Cu ores thus are better attributed to a BIF origin, but greatly reworked and enriched by late structural deformation and hydrothermal activities.

Conformity of modified O-ring test and maximal pinch strength for cross tape application direction.

PubMed

Lee, Jung-Hoon; Choi, Hyun-Su

2018-06-01

Although cross tape has recently been used by clinicians for various musculoskeletal conditions, scientific studies on the direction of cross tape application are lacking. The present study aimed to investigate whether the direction of cross tape application affected the outcomes of the modified O-ring test and maximal pinch strength using a pinch gauge and the conformity between these 2 tests when cross tape was applied to the forearm muscles of individuals with no upper extremity pain and no restriction of joint range of motion.This study used a single-blinding crossover design. The subjects comprised 39 adults (16 men and 23 women). Cross tape was applied to the dominant hand so that the 4 rows were at an angle of 45° to the right or left of the direction of the flexor digitorum superficialis muscle fibers, and then the subjects underwent a modified O-ring test and a test of maximal pinch strength using a pinch gauge. Both tests were performed in both directions, and the order of the directions and tests was randomized. SPSS 18.0 was used for statistical analysis. Cohen's kappa coefficient was used to analyze the conformity of the results from the 2 tests. The statistical significance level was P < .05. A positive response in the modified O-ring test and maximal pinch strength were both affected by cross tape direction. The modified O-ring test and maximal pinch strength using pinch gauge results were in agreement (P < .00), and the kappa coefficient was significant at 1.00. The direction of cross tape application that produced a positive response in the modified O-ring test also produced greater maximal pinch strength. Thus, we propose that when applying cross tape to muscles, the direction of the 4 lines of the cross tape should be 45° relative to the direction of the muscle fibers, toward the side that produces a positive response in the modified O-ring test or produces the greatest maximal pinch strength using a pinch gauge.

Mineralogy, paragenesis, and mineral zoning of the Bulldog Mountain vein system, Creede District, Colorado

USGS Publications Warehouse

Plumlee, Geoffrey S.; Heald Whitehouse-Veaux, Pamela

1994-01-01

The Bulldog Mountain vein system, Creede district, Colorado, is one of four major epithermal vein systems from which the bulk of the district's historical Ag-Pb-Zn-Cu production has come. Ores deposited along the vein system were discovered in 1965 and were mined from 1969 to 1985.Six temporally gradational mineralization stages have been identified along the Bulldog Mountain vein system, each with a characteristic suite of minerals deposited or leached and a characteristic distribution within the vein system; some of these stages are also strongly zoned within the vein system. Stage A was dominated by deposition of rhodochrosite along the lower levels of the Bulldog Mountain ore zone. Stage B in the northern parts of the ore zone is characterized by abundant fine-grained sphalerite and galena, with lesser tetrahedrite and minor chlorite and hematite. With increasing elevation to the south, stage B ores become progressively more barite and silver rich, with alternating barite and fine-grained sphalerite + galena generations; native silver + or - acanthite assemblages are also locally abundant within southern stage B barite sulfide ores, whereas chalcopyrite and other Cu and Ag sulfides and sulfosalts are present erratically in minor amounts. Stage C in the upper and northern portions of the ore zone is characterized by abundant quartz and fluorite, minor adularia, hematite, Mn siderite, sphalerite, and galena, and major leaching of earlier barite; to the south, some barite and sulfides may have been deposited. Stage D sphalerite and galena were deposited in the upper and northern portions of the ore zone; a barite- and silver-rich facies of this stage may also be present in the southern portions of the vein system. Late in stage D, mineralogically complex assemblages containing chalcopyrite, tetrahedrite, polybasite, bornite, pyrargyrite, and a variety of other sulfides and sulfosalts were deposited in modest amounts throughout the vein system. This complex assemblage marked the transition to stage E. During stage E, the final sulfide stage, abundant botryoidal pyrite and marcasite with lesser stibnite, sphalerite, and sulfosalts were deposited primarily along the top of the Bulldog Mountain ore zone. Stage F, the final mineralization stage along the vein system, is marked by wire silver and concurrent leaching of earlier sulfides and sulfosalts; this stage may reflect the transition to a supergene environment.The sequence of mineralization stages identified in this study along the Bulldog Mountain system can be correlated with corresponding stages identified by other researchers along the OH and P veins, and the southern Amethyst vein system. Mineral zoning patterns identified along the Bulldog Mountain vein system also parallel larger scale zoning patterns across the central and southern Creede district.The complex variations in mineral assemblages documented in time and space along the Bulldog Mountain vein system were produced by the combined effects of many processes. Large-scale changes in vein mineralogy over time produced discrete mineralization stages. Short-term mineralogical fluctuations produced complex interbanding of mineralogically distinct generations. Fluid chemistry evolution within the vein system produced large-scale lateral zoning patterns within certain stages. Hypogene leaching substantially modified the distributions of some minerals. Finally, structural activity, mineral deposition, and mineral leaching modified fluid flow pathways repeatedly during mineralization, and so added to the complex mineral distribution patterns within the vein system.

Exploration for uranium deposits in the Atkinson Mesa area, Montrose County, Colorado

USGS Publications Warehouse

Brew, Daniel Allen

1954-01-01

The U.S. Geological Survey explored the Atkinson Mesa area for uranium- and vanadium-bearing deposits from July 2, 1951, to June 18, 1953, with 397 diamond-drill holes that totaled 261,251 feet. Sedimentary rocks of Mesozoic age are exposed in the Atkinson Mesa area. They are: the Brushy Basin member of the Upper Jurassic Morrison formation, the Lower Cretaceous Burro Canyon formation, and the Upper and Lower Cretaceous Dakota sandstone. All of the large uranium-vanadium deposits discovered by Geological Survey drilling are in a series of sandstone lenses in the upper part of the Salt Wash member of the Jurassic Morrison formation. The deposits are mainly tabular and blanket-like, but some elongate pod-shaped masses, locally called "rolls" may be present. The mineralized material consists of sandstone impregnated with a uranium mineral which is probably coffinite, spme carnotite, and vanadium minerals, thought to be mainly corvusite and montroseite. In addition,, some mudstone and carbonaceous material is similarly impregnated. Near masses of mineralized material the sandstone is light gray or light brown, is generally over 40 feet thick, and usually contains some carbonaceous material and abundant disseminated pyrite or limonite stain. Similarly, the mudstone in contact with the ore-bearing sandstone near bodies of mineralized rock is commonly blue gray, as compared to its dominant red color away from ore deposits. Presence and degree of these features are useful guides in exploring for new deposits.

Ore deposits and epithermal evidences associated with intra-magmatic faults at Aïn El Araâr-Oued Belif ring structure (NW of Tunisia)

NASA Astrophysics Data System (ADS)

Aissa, Wiem Ben; Aissa, Lassaâd Ben; Amara, Abdesslem Ben Haj; Tlig, Said; Alouani, Rabah

2017-03-01

Hydrothermal ore deposits at Aïn El Araâr-Oued Belif location are classified as epithermal deposits type. The ore bodies are hosted by upper Turonian (8-9 M.y) volcanic rhyodacitic complex. Polymetallic sulfide orebodies are mainly concentrated within intra-magmatic faults. Petrographic, XRD, and TEM-STEM investigations revealed that ore minerals are essentially, arsenopyrite, pyrite, chalcopyrite, pyrrhotite, hematite, goethite and magnetite with Au, Ag and Pt trace metals. Gangue minerals are mainly adularia, quartz, sericite, alunite, tridymite, chlorite, phlogopite and smectite. Epithermal alteration is well zoned with four successive characteristic zones: (1) zone of quartz-adularia-sericite and rare alunite; (2) zone of kaolinite and plagioclase albitization; (3) intermediate zone of illite-sericite; (4) sapropelic alteration type zone of chlorite-smectite and rare illite. This can be interpreted as a telescoping of two different acidity epithermal phases; low sulfidation (adularia-sericite) and high sulfidation (quartz-alunite), separated in time or due to a gradual increase of fluids acidity and oxicity within the same mineralization phase. Brecciated macroscopic facies with fragments hosting quartz-adularia-sericite minerals (low-sulfidation phase) without alunite, support the last hypothesis. Geodynamic context and mineral alteration patterns are closely similar to those of Maria Josefa gold mine at SE of Spain which exhibit a volcanic-hosted epithermal ore deposit in a similar vein system, within rhyolitic ignimbrites, altered to an argillic assemblage (illite-sericite abundant and subordinate kaolinite) that grades outwards into propylitic alteration (Sanger-von Oepen et al. (1990)). Mineralogical and lithologic study undertaken in the volcanic host rock at Aïn El Araâr-Oued Belif reveals a typical epithermal low-sulfidation and high-sulfidation ore deposits with dominance of low-sulfidation. Host rocks in these systems range from silicic to intermediate for adularia-sericite type (low sulfidation) to rhyodacite for quartz-alunite type (high sulfidation).

Lead Isotope Geochemistry of Mississippi Valley-Type Pb-Zn Deposits of the Ozark Region, U.S. Midcontinent: Constraints on the Origin of Ore Metals

NASA Astrophysics Data System (ADS)

Potra, A.

2015-12-01

The Ozark region of the U.S. midcontinent is one of the world's most important provinces of MVT mineralization, hosting world-class ore deposits. The ores in the Tri-State (TS) and Northern Arkansas (NA) districts, dominated by sphalerite, are mainly hosted by platform carbonate rocks and vary in age from Ordovician and Mississippian for NA and Mississippian for TS. The deposits are considered to have formed from a regional hydrothermal flow system consisting of sedimentary brines discharged from the Arkoma basin and adjacent platform during the Late Pennsylvanian to Early Permian Ouachita orogeny. New MC-ICP-MS Pb isotope analyses of sphalerites are presented in order to compare and contrast the isotopic signature of ores from the NA and TS districts with those from other MVT districts from central and eastern US and trace metal sources. The Pb isotope ratios of ores from the TS District (208Pb/204Pb between 40.7443 and 41.2626; 207Pb/204Pb between 15.8633 and 15.9571; 206Pb/204Pb between 21.8373 and 22.1956) plot in an area that is superimposed on the Pb isotope field defined by samples from the Central Missouri District, suggesting similar metal sources. The sphalerites are less radiogenic than samples from the Upper Mississippi Valley District, but more radiogenic than samples from any other MVT district. Sphalerites from the NA District have lower Pb isotope values (208Pb/204Pb between 39.4633 and 40.8863; 207Pb/204Pb between 15.8216 and 15.9176; 206Pb/204Pb between 20.2396 and 21.6438) than the TS District ores; they plot below the field defined by samples from the Illinois-Kentucky district and overlap the field defined by ores from the Southeast Missouri (Viburnum and Old Lead Belt) district, implying similar metal sources. Current data suggest that basement of Grenvillian age (1 - 1.2 by), thought to be present in Arkansas, to the south of the Viburnum Trend, may be a likely source of the radiogenic Pb component. Pb data from ores in the NA and the Southeast Missouri districts are collinear with data from the TS and Central Missouri districts.

Sulphur-Rich Melt At Upper Crustal Levels At Cerro La Torta, Central Andes: Evidence From Melt Inclusions Assemblages.

NASA Astrophysics Data System (ADS)

Cannatelli, C.; Godoy, B.; Alvear, B.; Moncada, D.

2016-12-01

Central Andes present some of the biggest and most important porphyry copper ore deposits in the world. Porphyry copper ore formation is related to precipitation of ore minerals from sulphur and chlorine-rich fluids. Genesis of these deposits occurred 4 km below surface, while mineralized fluids are released by magmatic melts located between 5 and 15 km depth (Sillitoe, 2010). Cerro La Torta is part of a cluster of <105 ka rhyodacitic domes related to the waning stage of the Altiplano-Puna Volcanic Complex at Central Andes (Tierney et al., 2016). These domes reflect a crystal-rich mush layer at the upper crust - named Altiplano-Puna Magma Body (APMB) - which is proposed to be a voluminous partially molten body locate at shallow depth (4-25 km), with a thickness up to 11 km (Ward et al., 2014). Cerro La Torta is a crystal-rich ( 40% vol.) dacitic flow with plagioclase, amphibole, biotite, and quartz phenocrysts on a glassy (up to 50% vol.) groundmass. During detailed petrographic observation, two types of Melt Inclusions Assemblages (MIAs) were observed in the plagioclase. Group I is found in the core of crystals, and contains sulphide, pyrite ± bubbles. Group II of bubble-bearing MIAs is observed at the rim of the phenocrysts, with no associated sulphide mineral present. Melt Inclusions size ranges from 10-40 µm, suggesting an intermediate cooling rate (Roedder 1979). Out hypothesis is that during cooling, Group I MIA is trapped as result of a metal sulfur-rich event, leading to the suggestion that sulphide-bearing MIAs from Cerro La Torta are the evidence of mineralized magmas ponding at shallow crustal levels. Furthermore, the presence of MIAs in the mush-type magmas related to the APMB implies that such systems are suitable to porphyry copper ore generation. Roedder, 1979. The Evolution of the Igneous Rocks. 15-57 Sillitoe, 2010. Econ. Geol. 105:3-41 Tierney et al., 2016. Geology 44:683-686. doi:10.1130/G37968.1Ward et al., 2014. Earth Planet Sci Letters 404:43-54

The uranium-bearing nickel-cobalt-native silver deposits in the Black Hawk district, Grant County, New Mexico

USGS Publications Warehouse

Gillerman, Elliot; Whitebread, Donald H.

1953-01-01

The Black Hawk (Bullard Peak) district, Grant County, N. Mex., is 21 miles by road west of Silver City. From 1881 to 1893 more than $1,000,000.00 of high-grade silver ore is reported to have been shipped from the district. Since 1893 there has been no mining in the district except during a short period in 1917 when the Black Hawk mine was rehabilitated. Pre-Cambrian quartz diorite gneiss, which contains inclusions of quartzite, schist, monzonite, and quartz monzonite, is the most widespread rock in the district. The quartz diorite gneiss is intruded by many pre-Cambrian and younger rocks, including diorite granite, diabase, monzonite porphyry and andesite and is overlain by the Upper Cretaceous Beartooth quartzite. The monzonite porphyry, probably of late Cretaceous or early Tertiary age, forms a small stock along the northwestern edge of the district and numerous dikes and irregular masses throughout the district. The ore deposits are in fissure veins that contain silver, cobalt, and uranium. The ore minerals, which include native silver, niccolite, millerite, skutterudite, nickel skutterudite, bismuthinite, pitchblende, and sphalerite, are in a carbonate gangue in narrow, persistent veins, most of which trend northeasterly. Pitchblende has been identified in the Black Hawk and the Alhabra deposits and unidentified radioactive minerals were found at five other localities. The deposits that contain the radioactive minerals constitude a belt 600 to 1,500 feet wide that trends about N. 45° E., and is approximately parallel to the southeastern boundary of the monzonite porphyry stock. All the major ore deposits are in the quartz diorite gneiss in close proximity to the monzonite porphyry. The ore deposits are similar to the deposits at Great Bear Lake, Canada, and Joachimstahl, Czechoslovakia.

Thermal Aging of Oceanic Asthenosphere

NASA Astrophysics Data System (ADS)

Paulson, E.; Jordan, T. H.

2013-12-01

To investigate the depth extent of mantle thermal aging beneath ocean basins, we project 3D Voigt-averaged S-velocity variations from an ensemble of global tomographic models onto a 1x1 degree age-based regionalization and average over bins delineated by equal increments in the square-root of crustal age. From comparisons among the bin-averaged S-wave profiles, we estimate age-dependent convergence depths (minimum depths where the age variations become statistically insignificant) as well as S travel times from these depths to a shallow reference surface. Using recently published techniques (Jordan & Paulson, JGR, doi:10.1002/jgrb.50263, 2013), we account for the aleatory variability in the bin-averaged S-wave profiles using the angular correlation functions of the individual tomographic models, we correct the convergence depths for vertical-smearing bias using their radial correlation functions, and we account for epistemic uncertainties through Bayesian averaging over the tomographic model ensemble. From this probabilistic analysis, we can assert with 90% confidence that the age-correlated variations in Voigt-averaged S velocities persist to depths greater than 170 km; i.e., more than 100 km below the mean depth of the G discontinuity (~70 km). Moreover, the S travel time above the convergence depth decays almost linearly with the square-root of crustal age out to 200 Ma, consistent with a half-space cooling model. Given the strong evidence that the G discontinuity approximates the lithosphere-asthenosphere boundary (LAB) beneath ocean basins, we conclude that the upper (and probably weakest) part of the oceanic asthenosphere, like the oceanic lithosphere, participates in the cooling that forms the kinematic plates, or tectosphere. In other words, the thermal boundary layer of a mature oceanic plate appears to be more than twice the thickness of its mechanical boundary layer. We do not discount the possibility that small-scale convection creates heterogeneities in the oceanic upper mantle; however, the large-scale flow evidently advects these small-scale heterogeneities along with the plates, allowing the upper part of the asthenosphere to continue cooling with lithospheric age. The dominance of this large-scale horizontal flow may be related to the high stresses associated with its channelization in a thin (~100 km) asthenosphere, as well as the possible focusing of the subtectospheric strain in a low-viscosity channel immediately above the 410-km discontinuity. These speculations aside, the observed thermal aging of oceanic asthenosphere is inconsistent with a tenet of plate tectonics, the LAB hypothesis, which states that lithospheric plates are decoupled from deeper mantle flow by a shear zone in the upper part of the asthenosphere.

Apparatus for testing skin samples or the like

DOEpatents

Holland, J.M.

1982-08-31

An apparatus for testing the permeability of living skin samples has a flat base with a plurality of sample-holding cavities formed in its upper surface, the samples being placed in counterbores in the cavities with the epidermis uppermost. O-rings of Teflon washers are respectively placed on the samples and a flat cover is connected to the base to press the rings against the upper surfaces of the samples. Media to maintain tissue viability and recovery of metabolites is introduced into the lower portion of the sample-holding cavities through passages in the base. Test materials are introduced through holes in the cover plate after assembly of the chamber.

VizieR Online Data Catalog: Horizontal temperature at Venus upper atmosphere (Peralta+, 2016)

NASA Astrophysics Data System (ADS)

Peralta, J.; Lopez-Valverde, M. A.; Gilli, G.; Piccialli, A.

2015-11-01

The dayside atmospheric temperatures in the UMLT of Venus (displayed in Figure 7A of this article) are listed as a CSV data file. These values consist of averages in bins of 5° in latitude and 0.25-hours in local time from dayside temperatures covering five years of data (from 2006/05/14 to 2011/06/05). These temperatures were inferred from the CO2 NLTE nadir spectra measured by the instrument VIRTIS-H onboard Venus Express (see article for full description of the procedure), and are representative of the atmospheric region between 10-2 to 10-5mb. Along with the temperatures, we also provide the corresponding error and the number of temperatures averaged in each bin. The format of the CSV file reasonably agrees with the expected format of the data files to be provided in the future version of the Venus International Reference Atmosphere (VIRA). (1 data file).

Aerosols increase upper tropospheric humidity over the North Western Pacific

NASA Astrophysics Data System (ADS)

Riuttanen, Laura; Bister, Marja; John, Viju; Sundström, Anu-Maija; Dal Maso, Miikka; Räisänen, Jouni; de Leeuw, Gerrit; Kulmala, Markku

2014-05-01

Water vapour in the upper troposphere is highly important for the global radiative transfer. The source of upper tropospheric humidity is deep convection, and aerosol effects on them have got attention only recently. E.g., aerosol effects on deep convective clouds have been missing in general circulation models (Quaas et al., 2009). In deep convection, aerosol effect on cloud microphysics may lead to more ice precipitation and less warm rain (Khain et al., 2005), and thus more water vapour in upper troposphere (Bister & Kulmala, 2011). China outflow region over the Pacific Ocean was chosen as a region for a more detailed study, with latitudes 25-45 N and three longitude slots: 120-149 E, 150-179 E and 150-179 W. In this study, we used satellite measurements of aerosol optical depth (AOD) and upper tropospheric humidity (UTH). AOD was obtained from the MODIS instrument onboard Terra satellite, that crosses the equator southward at 10:30 AM local solar time (Remer et al., 2005). UTH was obtained from a microwave humidity sounder (MHS) onboard MetOp-A satellite, with passing time at 9:30 PM local solar time. It measures relative humidity of a layer extending approximately from 500 to 200 hPa. We binned the AOD and UTH data according to daily rainfall product 3B42 from Tropical Rainfall Measuring Mission (TRMM) satellite. Binning the data according to the amount of precipitation gives us a new way to account for the possible aerosol invigoration effect on convection and to alleviate the contamination and causality problems in aerosol indirect effect studies. In this study, we show for the first time, based on satellite data, that there is a connection between upper tropospheric humidity and aerosols. Anthropogenic aerosols from China increase upper tropospheric humidity, which causes a significant positive local radiative forcing in libRadtran radiative transfer model (Mayer & Kylling, 2005). References: Bister, M. & Kulmala, M. (2011). Atmos. Chem. Phys., 11, 4577-4586. Khain, A., Rosenfeld, D. & Pokrovsky, A. (2005). Q. J. R. Meteorol. Soc., 131, 2639-2663. Mayer, B. & Kylling, A. (2005). Atmos. Chem. Phys., 5, 1855-1877. Remer, L. A. et al. (2005). J. Atmos. Sci., 62, 947-973. Quaas, J. et al. (2009). Atmos. Chem. Phys., 9, 8697-8717.

The benchmark halo giant HD 122563: CNO abundances revisited with three-dimensional hydrodynamic model stellar atmospheres

NASA Astrophysics Data System (ADS)

Collet, R.; Nordlund, Å.; Asplund, M.; Hayek, W.; Trampedach, R.

2018-04-01

We present an abundance analysis of the low-metallicity benchmark red giant star HD 122563 based on realistic, state-of-the-art, high-resolution, three-dimensional (3D) model stellar atmospheres including non-grey radiative transfer through opacity binning with 4, 12, and 48 bins. The 48-bin 3D simulation reaches temperatures lower by ˜300-500 K than the corresponding 1D model in the upper atmosphere. Small variations in the opacity binning, adopted line opacities, or chemical mixture can cool the photospheric layers by a further ˜100-300 K and alter the effective temperature by ˜100 K. A 3D local thermodynamic equilibrium (LTE) spectroscopic analysis of Fe I and Fe II lines gives discrepant results in terms of derived Fe abundance, which we ascribe to non-LTE effects and systematic errors on the stellar parameters. We also determine C, N, and O abundances by simultaneously fitting CH, OH, NH, and CN molecular bands and lines in the ultraviolet, visible, and infrared. We find a small positive 3D-1D abundance correction for carbon (+0.03 dex) and negative ones for nitrogen (-0.07 dex) and oxygen (-0.34 dex). From the analysis of the [O I] line at 6300.3 Å, we derive a significantly higher oxygen abundance than from molecular lines (+0.46 dex in 3D and +0.15 dex in 1D). We rule out important OH photodissociation effects as possible explanation for the discrepancy and note that lowering the surface gravity would reduce the oxygen abundance difference between molecular and atomic indicators.

Duration of mineralization and fluid-flow history of the Upper Mississippi Valley zinc-lead district

USGS Publications Warehouse

Rowan, E.L.; Goldhaber, M.B.

1995-01-01

Studies of fluid inclusions in sphalerite and biomarkers from the Upper Mississippi Valley zinc district show homogenization temperatures to be primarily between 90 and 150??C, yet show relatively low levels of thermal maturity. Numerical calculations are used to simulate fluid and heat flow through fracture-controlled ore zones and heat transfer to the adjacent rocks. Combining a best-fit path through fluid-inclusion data with measured thermal alteration of biomarkers, the time interval during which mineralizing fluids circulated through the Upper Mississippi Valley district was calculated to be on the order of 200 ka. Cambrian and Ordovician aquifers underlying the district, principally the St. Peter and Mt. Simon Sandstones, were the source of the mineralizing fluid. The duration of mineralization thus reflects the fluid-flow history of these regional aquifers. -from Authors

Mineralogical and geochemical characteristics of the Noamundi-Koira basin iron ore deposits (India)

NASA Astrophysics Data System (ADS)

Mirza, Azimuddin; Alvi, Shabbar Habib; Ilbeyli, Nurdane

2015-04-01

India is one of the richest sources of iron ore deposits in the world; and one of them is located in the Noamundi-Koira basin, Singhbhum-Orissa craton. The geological comparative studies of banded iron formation (BIF) and associated iron ores of Noamundi-Koira iron ore deposits, belonging to the iron ore group in eastern India, focus on the study of mineralogy and major elemental compositions along with the geological evaluation of different iron ores. The basement of the Singhbhum-Orissa craton is metasedimentary rocks which can be traced in a broadly elliptical pattern of granitoids, surrounded by metasediments and metavolcanics of Greenstone Belt association. The Singhbhum granitoid is intrusive into these old rocks and to younger, mid Archaean metasediments, including iron formations, schists and metaquartzites and siliciclastics of the Precambrian Iron Ore Group (Saha et al., 1994; Sharma, 1994). The iron ore of Noamundi-Koira can be divided into seven categories (Van Schalkwyk and Beukes 1986). They are massive, hard laminated, soft laminated, martite-goethite, powdery blue dust and lateritic ore. Although it is more or less accepted that the parent rock of iron ore is banded hematite jasper (BHJ), the presence of disseminated martite in BHJ suggests that the magnetite of protore was converted to martite. In the study area, possible genesis of high-grade hematite ore could have occurred in two steps. In the first stage, shallow, meteoric fluids affect primary, unaltered BIF by simultaneously oxidizing magnetite to martite and replacing quartz with hydrous iron oxides. In the second stage of supergene processes, deep burial upgrades the hydrous iron oxides to microplaty hematite. Removal of silica from BIF and successive precipitation of iron resulted in the formation of martite- goethite ore. Soft laminated ores were formed where precipitation of iron was partial or absent. The leached out space remains with time and the interstitial space is generally filled with kaolinite and gibbsite, which make it low grade. Massive iron ores are devoid of any lamination and usually associated with BHJ and lower shale. The thickness of the massive ore layer varies with the location. The massive iron ore grades in to well-developed bedded BHJ in depth. Blue dust occurs in association with BHJ as pockets and layers. Although blue dust and friable ore are both powdery ores, and subjected to variable degree of deformation, leading to the formation of folding, faulting and joints of complex nature produce favourable channels. Percolating water play an important role in the formation of blue dust and the subterranean solution offers the necessary acidic environment for leaching of quartz from the BHJ. The dissolution of silica and other alkalis are responsible for the formation of blue dust. The friable and powdery ore on the other hand are formed by soft laminated ore. As it is formed from the soft laminated ore, its alumina content remains high similar to soft laminated ore compaired to blue dust. Mineralogy study suggests that magnetite was the principal iron oxide mineral, now a relict phase whose depositional history is preserved in BHJ, where it remains in the form of martite. The platy hematite is mainly the product of martite. The different types of iron ores are intricately related with the BHJ. Hard laminated ores, martite-goethite ore and soft laminated ore are resultant of desilicification process through the action of hydrothermal fluids. Geochemistry of banded iron-formations of the Noamundi-Koira iron ore deposits shows that they are detritus-free chemical precipitates. The mineralogical and geochemical data suggest that the hard laminated, massive, soft laminated ores and blue dust had a genetic lineage from BIF's aided with certain input from hydrothermal activity. The comparative study of major elemental composition of the basin samples and while plotting a binary diagram, it shows a relation between major oxides against iron oxides, in which iron oxides is taken as a reference oxide (Mirza, 2011). On the other hand, by plotting a binary diagram between chemical index of alteration (CIA) and other oxides while taking the samples of lower, middle and upper shales. It reflects an immobility and mobility of ions during partial and complete weathering processes (Mirza, 2011). Geochemical data indicate that BIF are in general detritus free chemical precipitates. Fe2O3 content of BHJ are varies in between 36.6% to 65.04%. In hard laminated ore, Fe2O3 content varies from 93.8% to 96.38%, Soft laminated ore varies from 83.64% to 89.5% and laterite ore varies from 53.5% to 79.11%. Fe2O3 content in Martite- Goethite ore varies from 86.38% to 89.42% and blue dust having 90.74% to 95.86% and all other oxides like SiO2, Al2O3, CaO, MgO, K2O, Na2O are decreases. Major part of the iron could have been added to the bottom sea water by hydrothermal solutions derived from hydrothermally active anoxic marine environments. The presence of intacalated tuffaceous shales pointing towards the genesis of iron, which could have leached from sea floor by volcanogenic process. Iron and silica of BIF were provided by the hydrothermal solutions emplaced at the vent sites situated at the Archean-Mid Oceanic Ridges. References: Mirza A (2011). Major element geochemistry of iron ore deposits in Noamundi-Koira basin of Singhbhum-Orissa craton (India). MSc thesis, Aligarh Muslim University, India. Saha AK (1994). Crustal evolution of Singhbhum, North Orissa, Eastern India; Geol. Soc. India Memoir 27 341. Sharma M, Basu AR and Ray SL (1994). Sm-Nd isotopic and geochemical study of the Archaean tonalite-amphibolite association from the eastern Indian craton. Contrib. Mineral Petrol. 117:45-55. Van Schalkwyk J and Beukes N J (1986). The Sishen iron ore deposit, Griqualand West; In: Mineral deposits of Southern Africa (eds) Annhaeusser C R and Maske S S, Geological Society of South Africa, Johannesburg, 931-956.

Geology, ore facies and sulfur isotopes geochemistry of the Nudeh Besshi-type volcanogenic massive sulfide deposit, southwest Sabzevar basin, Iran

NASA Astrophysics Data System (ADS)

Maghfouri, Sajjad; Rastad, Ebrahim; Mousivand, Fardin; Lin, Ye; Zaw, Khin

2016-08-01

The southwest Sabzevar basin is placed in the southwestern part of a crustal domain known as the Sabzevar zone, at the north of Central Iranian microcontinent. This basin hosts abundant mineral deposits; particularly of the Mn exhalative and Cu-Zn volcanogenic massive sulfide (VMS) types. The evolution of this basin is governed by the Neo-tethys oceanic crust subduction beneath the Central Iranian microcontinent and by the resulting continental arc (Sanandaj-Sirjan) and back-arc (Sabzevar-Naien). This evolution followed two major sequences: (I) Lower Late Cretaceous Volcano-Sedimentary Sequence (LLCVSS), which is indicated by fine-grained siliciclastic sediments, gray basic coarse-grained different pyroclastic rocks and bimodal volcanism. During this stage, tuff-hosted stratiform, exhalative Mn deposits (Nudeh, Benesbourd, Ferizy and Goft), oxide Cu deposits (Garab and Ferizy) and Cu-Zn VMS (Nudeh, Chun and Lala) deposits formed. (II) Upper Late Cretaceous Sedimentary Dominated Sequence (ULCSS), including pelagic limestone, marly tuff, silty limestone and marl with minor andesitic tuff rocks. The economically most important Mn (Zakeri and Cheshmeh-sefid) deposits of Sabzevar zone occur within the marly tuff of this sequence. The Nudeh Cu-Zn volcanogenic massive sulfide (VMS) deposit is situated in the LLCVSS. The host-rock of deposits consists of alkali olivine basalt flow and tuffaceous silty sandstone. Mineralization occurs as stratiform blanket-like and tabular orebodies. Based on ore body structure, mineralogy, and ore fabric, we recognize three different ore facies in the Nudeh deposit: (1) a stringer zone, consisting of a discordant mineralization of sulfides forming a stockwork of sulfide-bearing quartz veins cutting the footwall volcano-sedimentary rocks; (2) a massive ore, consisting of massive replacement pyrite, chalcopyrite, sphalerite and Friedrichite with magnetite; (3) bedded ore, with laminated to disseminated pyrite, and chalcopyrite. Chloritization, silicification, sericitization and epidotization are the main wall-rock alterations; alteration intensity increases towards the stringer zone. The δ34S composition of the sulfides ranges from -1.5‰ to +3.69‰ with a general increase of δ34S ratios of massive ore facies to stockwork zone. The heavier values indicate that some of the sulfur was derived from seawater sulfate that was ultimately thermochemically reduced in deep hydrothermal reaction zones. Sulfur isotopes, along with sedimentological, textural, petrological, mineralogical, and geochemical evidences, suggest that this deposit should be classified as a Besshi-type VMS ore deposit.

The giant Upper Yangtze Pb-Zn province in SW China: Reviews, new advances and a new genetic model

NASA Astrophysics Data System (ADS)

Zhou, Jia-Xi; Xiang, Zhen-Zhong; Zhou, Mei-Fu; Feng, Yue-Xing; Luo, Kai; Huang, Zhi-Long; Wu, Tao

2018-04-01

In the western margin of the Yangtze Block, SW China, the Emeishan large igneous province (ELIP) is spatially associated with >400 carbonate-hosted epigenetic Pb-Zn deposits. These deposits form the giant Upper Yangtze Pb-Zn metallogenic province with >20 Mt base metals. In the southeastern part of this province, the important Pb-Zn deposits include those of the Yinchangpo, Yunluhe, Maozhachang, Tianqiao, Banbanqiao, Mangdong, Shaojiwan, Liangyan, Qingshan, Shanshulin, Nayongzhi and Guanziyao deposits. Sulfide ore bodies in these deposits are (i) hosted in late Ediacaran to middle Permian limestone, dolomitic limestone and dolostone; (ii) structurally controlled by reverse fault-anticline tectonic systems; and (iii) spatially associated with the ELIP flood basalts and mafic dikes, and early Permian, early Carboniferous and early Cambrian organic matter-rich black shales. C-O isotopic compositions suggest that dolostone and limestone, mantle-derived rocks of the ELIP, and sedimentary organic matters supplied C-O to the hydrothermal systems through water/rock (W/R) interaction. New and existing S isotopic compositions of sulfides imply multiple sources of S and the reduction of sulfate through both abiotic thermochemical (TSR) and bacterially mediated (BSR) processes. Zn isotopes indicate that the sources of Zn were most likely related to the ELIP with various contributions from sediments and basements locally. Pb isotope signatures are suggestive of derivation of Pb from basements and sedimentary rocks with variable influences from the ELIP. Sr isotopes support that mantle-derived rocks, sediments and basements were involved in Pb-Zn mineralization, and they have various contributions in different deposits. We consider that the Pb-Zn deposits in the Upper Yangtze province are the mixed products of multiple S species-bearing solutions and metal-rich fluids, both of which were derived from, flowed through or interacted with multiple lithostratigraphic units in the western Yangtze Block. The change of tectonic regimes from extension to compression after eruption of basalts of the ELIP, and then to extension during Early Mesozoic, facilitated extraction, migration, and excretion of ore-forming metals and associated fluids. Mixing of fluids and reduction geochemical barrier activated TSR, causing cyclical carbonate dissolution, CO2 degassing and recrystallization (namely carbonate buffer). All these processes triggered continuous precipitation of huge amounts of hydrothermal minerals. Underplating and eruption of ELIP basalts provided heat flow, fluids and volatiles, whereas the basalts acted as an impermeable and protective layer, and even as ore-hosting rocks. These Pb-Zn deposits have spatial and genetic association with igneous activities of the ELIP, and are characterized by high ore grades (>10 wt% Pb + Zn), high concentrations of associated metals (e.g. Cu, Ag, Ge, and Cd), and medium-low temperatures (usually < 300 °C) and salinities (commonly < 20 wt% NaCl equiv.), all of which are significantly different from those of typical Mississippi Valley-type (MVT) deposits. Hence, the carbonate-hosted epigenetic Pb-Zn deposits in the Upper Yangtze metallogenic province representing to a new type of Pb-Zn deposits that are hosted in platform carbonate sequences and formed within compressional zones of passive margin tectonic settings.

Regularities of spatial association of major endogenous uranium deposits and kimberlitic dykes in the uranium ore regions of the Ukrainian Shield

NASA Astrophysics Data System (ADS)

Kalashnyk, Anna

2015-04-01

During exploration works we discovered the spatial association and proximity time formation of kimberlite dykes (ages are 1,815 and 1,900 Ga for phlogopite) and major industrial uranium deposits in carbonate-sodium metasomatites (age of the main uranium ore of an albititic formation is 1,85-1,70 Ga according to U-Pb method) in Kirovogradsky, Krivorozhsky and Alekseevsko-Lysogorskiy uranium ore regions of the Ukrainian Shield (UkrSh) [1]. In kimberlites of Kirovogradsky ore region uranium content reaches 18-20 g/t. Carbon dioxide is a major component in the formation of hydrothermal uranium deposits and the formation of the sodium in the process of generating the spectrum of alkaline ultrabasic magmas in the range from picritic to kimberlite and this is the connection between these disparate geochemical processes. For industrial uranium deposits in carbonate-sodium metasomatitics of the Kirovogradsky and Krivorozhsky uranium ore regions are characteristic of uranyl carbonate introduction of uranium, which causes correlation between CO2 content and U in range of "poor - ordinary - rich" uranium ore. In productive areas of uranium-ore fields of the Kirovogradsky ore region for phlogopite-carbonate veinlets of uranium ore albitites deep δ13C values (from -7.9 to -6.9o/oo) are characteristic. Isotope-geochemical investigation of albitites from Novokonstantynovskoe, Dokuchaevskoe, Partyzanskoe uranium deposits allowed obtaining direct evidence of the involvement of mantle material during formation of uranium albitites in Kirovogradsky ore region [2]. Petrological characteristics of kimberlites from uranium ore regions of the UkrSh (presence of nodules of dunite and harzburgite garnet in kimberlites, diamonds of peridotite paragenesis, chemical composition of indicator minerals of kimberlite, in particular Gruzskoy areas pyropes (Cr2O3 = 6,1-7,1%, MgO = 19,33-20,01%, CaO = 4,14-4,38 %, the content of knorringite component of most grains > 50mol%), chromites (Cr2O3 = 45,32-62,17%, MgO = 7,3-12,5%) allow us to estimate the depth of generation of kimberlite magmas more than 170-200 km. Ilmenites show two groups according to MgO, Cr2O3 and TiO2 content. Reconstructions of the mantle sections show also two intervals of pressures divided at 4.5 GPa, the upper part is highly metasomatized This high degree metasomatism is determined for almost all mantle columns. It is suggested that large-scale of uranium-bearing mantle fluids may be associated with the ancient degasation during the subduction which is highly enriched in U component . Analysis of the reasons for the marked association kimberlitic dykes and major industrial uranium deposits in carbonate-sodium metasomatic in the UkrSh led to the conclusion that hydrothermal uranium deposits are confined to the supply mantle fluid systems of mantle fault zones exercising brings sodium carbonate solutions enriched uranium from mantle sources. References: 1. Kalashnik A.A. New prognostic-evaluation criteria in technology prognosis of forming industrial endogenous uranium deposits of the Ukrainian Shield, 2014. Scientific proceedings of UkrSGRI, № 2, p. 27-54 (in Russian) 2. Stepanjuk L.M., Bondarenko S.V., Somka V.O. and other, 2012. Source of uranium and uranium-bearing sodium albitites for example of Dokuchaievskogo field of the Ingulsky megablock of the UkrSh: Abstracts of scientific conference "Theoretical issues and research practice metasomatic rocks and ores" (Kyiv, 14-16 March 2012), IGMOF, p.78-80. (in Ukrainian)

Magmatic controls on the genesis of porphyry Cu-Mo-Au deposits: The Bingham Canyon example

NASA Astrophysics Data System (ADS)

Grondahl, Carter; Zajacz, Zoltán

2017-12-01

Bingham Canyon is one of the world's largest porphyry Cu-Mo-Au deposits and was previously used as an example to emphasize the role of magma mixing and magmatic sulphide saturation in the enhancement of ore fertility of magmatic systems. We analyzed whole rocks, minerals, and silicate melt inclusions (SMI) from the co-genetic, ore-contemporaneous volcanic package (∼38 Ma). As opposed to previous propositions, whole-rock trace element signatures preclude shoshonite-latite genesis via mixing of melanephelinite and trachyte or rhyolite, whereas core to rim compositional profiles of large clinopyroxene phenocrysts suggests the amalgamation of the ore-related magma reservoir by episodic recharge of shoshonitic to latitic magmas with various degrees of differentiation. Major and trace element and Sr and Nd isotopic signatures indicate that the ore-related shoshonite-latite series were generated by low-degree partial melting of an ancient metasomatized mantle source yielding volatile and ore metal rich magmas. Latite and SMI compositions can be reproduced by MELTS modeling assuming 2-step lower and upper crustal fractionation of a primary shoshonite with minimal country rock assimilation. High oxygen fugacities (≈ NNO + 1) are prevalent as evidenced by olivine-spinel oxybarometry, high SO3 in apatite, and anhydrite saturation. The magma could therefore carry significantly more S than would have been possible at more reducing conditions, and the extent of ore metal sequestration by magmatic sulphide saturation was minimal. The SMI data show that the latites were Cu rich, with Cu concentrations in the silicate melt reaching up to 300-400 ppm at about 60 wt% SiO2. The Au and Ag concentrations are also high (1.5-4 and 50-200 ppb, respectively), but show less variation with SiO2. A sudden drop in Cu and S concentrations in the silicate melt at around 65 wt% SiO2 in the presence of high Cl, Mo, Ag, and Au shows that the onset of effective metal extraction by fluid exsolution occurred at a relatively late stage of magma evolution. Overall, our results show that fluid exsolution during simple magmatic differentiation of oxidized alkaline magmas is capable of producing giant porphyry Cu deposits.

Porphyry-Style Petropavlovskoe Gold Deposit, the Polar Urals: Geological Position, Mineralogy, and Formation Conditions

NASA Astrophysics Data System (ADS)

Vikentyev, I. V.; Mansurov, R. Kh.; Ivanova, Yu. N.; Tyukova, E. E.; Sobolev, I. D.; Abramova, V. D.; Vykhristenko, R. I.; Trofimov, A. P.; Khubanov, V. B.; Groznova, E. O.; Dvurechenskaya, S. S.; Kryazhev, S. G.

2017-11-01

Geological and structural conditions of localization, hydrothermal metasomatic alteration, and mineralization of the Petropavlovskoe gold deposit (Novogodnenskoe ore field) situated in the northern part of the Lesser Ural volcanic-plutonic belt, which is a constituent of the Middle Paleozoic island-arc system of the Polar Urals, are discussed. The porphyritic diorite bodies pertaining to the late phase of the intrusive Sob Complex play an ore-controlling role. The large-volume orebodies are related to the upper parts of these intrusions. Two types of stringer-disseminated ores have been revealed: (1) predominant gold-sulfide and (2) superimposed low-sulfide-gold-quartz ore markedly enriched in Au. Taken together, they make up complicated flattened isometric orebodies transitory to linear stockworks. The gold potential of the deposit is controlled by pyrite-(chlorite)-albite metasomatic rock of the main productive stage, which mainly develops in a volcanic-sedimentary sequence especially close to the contacts with porphyritic diorite. The relationships between intrusive and subvolcanic bodies and dating of individual zircon crystals corroborate a multistage evolution of the ore field, which predetermines its complex hydrothermal history. Magmatic activity of mature island-arc plagiogranite of the Sob Complex and monzonite of the Kongor Complex initiated development of skarn and beresite alterations accompanied by crystallization of hydrothermal sulfides. In the Early Devonian, due to emplacement of the Sob Complex at a depth of approximately 2 km, skarn magnetite ore with subordinate sulfides was formed. At the onset of the Middle Devonian, the large-volume gold porphyry Au-Ag-Te-W ± Mo,Cu stockworks related to quartz diorite porphyry—the final phase of the Sob Complex— were formed. In the Late Devonian, a part of sulfide mineralization was redistributed with the formation of linear low-sulfide quartz vein zones. Isotopic geochemical study has shown that the ore is deposited from reduced, substantially magmatic fluid, which is characterized by close to mantle values δ34S = 0 ± 1‰, δ13C =-6 to-7‰, and δ18O = +5‰ as the temperature decreases from 420-300°C (gold-sulfide ore) to 250-130°C (gold-(sulfide)-quartz ore) and pressure decreases from 0.8 to 0.3 kbar. According to the data of microanalysis (EPMA and LA-ICP-MS), the main trace elements in pyrite of gold orebodies are represented by Co (up to 2.52 wt %), As (up to 0.70 wt %), and Ni (up to 0.38 wt %); Te, Se, Ag, Au, Bi, Sb, and Sn also occur. Pyrite of the early assemblages is characterized by high Co, Te, Au, and Bi contents, whereas the late pyrite is distinguished by elevated concentrations of As (up to 0.7 wt %), Ni (up to 0.38 wt %), Se (223 ppm), Ag (up to 111 ppm), and Sn (4.4 ppm). The minimal Au content in pyrite of the late quartz-carbonate assemblage is up to 1.7 ppm and geometric average is 0.3 ppm. The significant correlation between Au and As (furthermore, negative-0.6) in pyrite from ore of the Petropavlovskoe deposit is recorded only for the gold-sulfide assemblage, whereas it is not established for other assemblages. Pyrite with higher As concentration (up to 0.7 wt %) is distinguished only for the Au-Te mineral assemblage. Taking into account structural-morphological and mineralogical-geochemical features, the ore-magmatic system of the Petropavlovskoe deposit is referred to as gold porphyry style. Among the main criteria of such typification are the spatial association of orebodies with bodies of subvolcanic porphyry-like intrusive phases at the roof of large multiphase pluton; the stockwork-like morphology of gold orebodies; 3D character of ore-alteration zoning and distribution of ore components; geochemical association of gold with Ag, W, Mo, Cu, As, Te, and Bi; and predominant finely dispersed submicroscopic gold in ore.

Magnetic properties of the Bled El Hadba phosphate-bearing formation (Djebel Onk, Algeria): Consequences of the enrichment of the phosphate ore deposit

NASA Astrophysics Data System (ADS)

Bezzi, Nacer; Aïfa, Tahar; Merabet, Djoudi; Pivan, Jean-Yves

2008-02-01

To improve the enrichment of the Thanetian marine phosphate ore deposit from the quarry of Bled El Hadba (Djebel Onk, Algeria) before its exploitation, we first conducted a joint study using different techniques for comparison. These studies reveal that magnetic minerals play a significant role within the matrix of the central productive unit which is squeezed between two other units. Magnetic separation procedures show that there are some positive correlations between magnetic susceptibility and grain size fraction (80-250 μm). These dolomite-rich fractions are more clearly separated. Different tools were used to characterize the magnetic minerals (X-ray, microprobe, differential scanning calorimetry, thermogravimetric and thermomagnetic analyses). They show correlations between magnetic phases and the presence of associated magnetic minerals within the matrix or included in the phosphate ore deposit. They enabled us to distinguish a series of magnetic minerals (magnetite, hematite, maghemite, goethite, ilmenite, pyrite, iron-titanium oxide and titanium oxide sulphate) and to determine that Fe and Ti are prevalent in the separated fractions, following the same variation as Mg. The phosphorous (phosphate) rate is higher in the non-magnetic material, especially in the layers that are rich in dolomitic carbonates (upper and lower units), which could be trapped within the dolomitic matrix, while Magnesium (dolomite) is more important in the magnetic fraction. The separation of phosphate elements and dolomite carbonates is effective and therefore the ore can be enriched through magnetic procedures. Comparison between products enriched by magnetic separation, flotation and calcination showed important differences, chemically, economically and technically speaking.

Genesis of the Permian karstic Pingguo bauxite deposit, western Guangxi, China

NASA Astrophysics Data System (ADS)

Liu, Xuefei; Wang, Qingfei; Zhang, Qizuan; Yang, Shujuan; Liang, Yayun; Zhang, Ying; Li, Yan; Guan, Tao

2017-10-01

More than 0.5 billion tons of late Permian bauxite overlies the karstic topography of the Maokou Formation of western Guangxi in China. Here, we provide new mineralogical, geochemical, Sr-Nd-Pb isotopic, and pyrite S isotope and trace element compositional data for the Pingguo bauxite deposit, aiming to further our understanding of the genesis of Permian bauxite. The Pingguo bauxite contains three distinct layers: a lower layer dominated by ferric clay or weathered iron ore, a middle layer of cryptocrystalline and oolitic bauxite ore, and an upper layer dominated by argillaceous bauxite. The bauxite ore is mainly diaspore, pyrite, chamosite, and anatase, whereas the argillaceous bauxite contains diaspore, kaolinite, pyrophyllite, pyrite, and anatase. Two types of pyrite have been identified within the bauxite: fine-grained and framboidal pyrite (Py1) occurring in aggregates and coarse-grained and euhedral pyrite (Py2). Py1 is enriched in trace elements and is thought to have a diagenetic origin, whereas Py2 is deficient in trace elements and is considered to have formed by later recrystallization. The S isotopic composition of pyrite (-34.11 to -18.91‰) and visible ovoid microorganisms within the bauxite provide evidences of microbial activity during bauxite formation. The Sr-Nd-Pb isotopic composition of the bauxite indicates that these ores were generated by the weathering of basalts belonging to the Emeishan Large Igneous Province (LIP) and limestones of the Maokou Formation. Microorganisms were likely to have enhanced the dissolution and weathering of the parent rock and facilitated the precipitation of diaspore under near-surface conditions.

The potential source of lead in the Permian Kupferschiefer bed of Europe and some selected Paleozoic mineral deposits in the Federal Republic of Germany

USGS Publications Warehouse

Wedepohl, K.H.; Delevaux, M.H.; Doe, B.R.

1978-01-01

New lead isotopic compositions have been measured for Paleozoic bedded and vein ore deposits of Europe by the high precision thermal emission (triple filament) technique. Eleven samples have been analyzed from the Upper Permian Kupferschiefer bed with representatives from Poland to England, three samples from the Middle Devonian Rammelsberg deposit and one from the Middle Devonian Meggen deposit, both of which are conformable ore lenses and are in the Federal Republic of Germany (FRG); and also two vein deposits from the FRG were analyzed, from Ramsbeck in Devonian host rocks and from Grund in Carboniferous host rocks. For Kupferschiefer bed samples from Germany, the mineralization is of variable lead isotopic composition and appears to have been derived about 250 m.y. ago from 1700 m.y. old sources, or detritus of this age, in Paleozoic sedimentary rocks. Samples from England, Holland, and Poland have different isotopic characteristics from the German samples, indicative of significantly different source material (perhaps older). The isotopic variability of the samples from the Kupferschiefer bed in Germany probably favors the lead containing waters coming from shoreward (where poor mixing is to be expected) rather than basinward (where better mixing is likely) directions. The data thus support the interpretation of the metal source already given by Wedepohl in 1964. Data on samples from Rammelsberg and Meggen tend to be slightly less radiogenic than for the Kupferschiefer, about the amount expected if the leads were all derived from the same source material but 100 to 150 m.y. apart in time. The vein galena from Ramsbeck is similar to that from Rammelsberg conformable ore lenses, both in rocks of Devonian age; vein galena from Grund in Upper Carboniferous country rocks is similar to some bedded Kupferschiefer mineralization in Permian rocks, as if the lead composition was formed at about the same time and from similar source material as the bedded deposits. Although heat has played a more significant role in the formation of some of these deposits (veins and Rammelsberg-Meggen) than in others (Kupferschiefer), there is no indication of radically different sources for the lead, all apparently coming from sedimentary source material containing Precambrian detritus. One feldspar lead sample from the Brocken-Oker Granite is not the same in isotopic composition as any of the ores analyzed. ?? 1978 Springer-Verlag.

Applications of the 190Pt-186Os isotope system to geochemistry and cosmochemistry

USGS Publications Warehouse

Walker, R.J.; Morgan, J.W.; Beary, E.S.; Smoliar, M.I.; Czamanske, G.K.; Horan, M.F.

1997-01-01

Platinum is fractionated from osmium primarily as a consequence of processes involving sulfide and metal crystallization. Consequently, the 190Pt-186Os isotope system (190Pt ??? 186Os + ??) shows promise for dating some types of magmatic sulfide ores and evolved iron meteorites. The first 190Pt-186Os isochrons are presented here for ores from the ca. 251 Ma Noril'sk, Siberia plume, and for group IIAB magmatic iron meteorites. Given the known age of the Noril'sk system, a decay constant for 190Pt is determined to be 1.542 ?? 10-12a-1, with ??1% uncertainty. The isochron generated for the IIAB irons is consistent with this decay constant and the known age of the group. The 186Os/188Os ratios of presumably young, mantle-derived osmiridiums and also the carbonaceous chondrite Allende were measured to high-precision to constrain the composition of the modern upper mantle. These compositions overlap, indicating that the upper mantle is chondritic within the level of resolution now available. Our best estimate for this 186Os/188Os ratio is 0.119834 ?? 2 (2??M). The 190Pt/186Os ratios determined for six enstatite chondrites average 0.001659 ?? 75, which is very similar to published values for carbonaceous chondrites. Using this ratio and the presumed composition of the modern upper mantle and chondrites, a solar system initial 186Os/188Os ratio of 0.119820 is calculated. In comparison to the modern upper mantle composition, the 186Os/188Os ratio of the Noril'sk plume was approximately 0.012% enriched in 186Os. Possible reasons for this heterogeneity include the recycling of Pt-rich crust into the mantle source of the plume and derivation of the osmium from the outer core. Derivation of the osmium from the outer core is our favored model. Copyright ?? 1997 Elsevier Science Ltd.

Audio-magnetotelluric investigation of allochthonous iron formations in the Archaean Reguibat shield (Mauritania): structural and mining implications

NASA Astrophysics Data System (ADS)

Bronner, G.; Fourno, J. P.

1992-11-01

The M'Haoudat range, considered as an allochthonous unit amid the strongly metamorphosed Archaean basement (Tiris Group), belongs to the Lower Proterozoic Ijil Group, weakly metamorphosed, constituted mainly by iron quartzites including red jaspers and high grade iron ore. Audio-magnetotelluric (AMT) soundings (frequency range 1-7500 HZ) were performed together with the systematic survey of the range (SNIM mining company). The non-linear least squares method was used to perform a smoothness-constrained data model. The obvious AMT resistivity contrasts between the M'Haoudat Unit (150-3500 ohm. m) and the Archaean basement (20 000 ohm. m) allow to state precisely that the two thrust surfaces, on both sides of the range, join together at a depth which increases from North-West to South-East, as the ore bodies. Inside the steeply dipping M'Haoudat Unit, the main beds of iron quartzites (1500-3500 ohm. m), schists (1000-1500 ohm. m) and hematite ores (150-300 ohm. m) were distinguished when their thickness exceeded 30 to 50 m. The existence of an hydrostatic level (1-50 ohm. m) and the steeply dipping architecture, very likely responsible for the lack of resistivity contrast on the upper part of some profiles, complicate the interpretation at high frequencies the thin layers being poorly defined.

The Uitkomst intrusion and Nkomati Ni-Cu-Cr-PGE deposit, South Africa: trace element geochemistry, Nd isotopes and high-precision geochronology

NASA Astrophysics Data System (ADS)

Maier, W. D.; Prevec, S. A.; Scoates, J. S.; Wall, C. J.; Barnes, S.-J.; Gomwe, T.

2018-01-01

The Uitkomst intrusion is a tubular mafic-ultramafic layered body that hosts one of South Africa's largest Ni-Cu-Cr-PGE deposits, Nkomati. The sulphide ore occurs in the form of massive lenses in the immediate quartzitic footwall and as disseminations within peridotite. The chromite ore forms an up to ˜10-m-thick layer in the lower portion of the intrusion. Uitkomst has generally been interpreted as a magma conduit, possibly related to the Bushveld event. Here, we present a new high-precision U-Pb zircon date of 2057.64 ± 0.69 Ma that overlaps with the age of the Merensky Reef of the Bushveld Complex and thus demonstrates a coeval relationship between the intrusions. Based on incompatible trace elements as well as O- and Nd isotope data (ɛNd -4.5 to -6.2), we show that the Uitkomst parent magmas were contaminated with up to 20% Archean upper crust prior to emplacement, and with up to 15% dolomitic country rock during emplacement. Ore formation at Nkomati was critically aided by substantial devolatisation and removal of dolomitic floor rocks leading to hydrodynamic concentration of sulphide and chromite during slumping of crystal mushes into the trough-like centre of the subsiding intrusion and its footwall.

The formation of ore mineral deposits on the Moon: A feasibility study

NASA Technical Reports Server (NTRS)

Taylor, Lawrence A.; Lu, Fengxiang

1992-01-01

Most of the ore deposits on Earth are the direct result of formation by hydrothermal solutions. Analogous mineral concentrations do not occur on the Moon, however, because of the absence of water. Stratified ore deposits form in layered instrusives on Earth due to fractional crystallization of magma and crystal settling of high-density minerals, particularly chromium in the mineral chromite. We have evaluated the possibility of such mineral deposition on the Moon, based upon considerations of 'particle settling velocities' in lunar vs. terrestrial magmas. A first approximation of Stoke's Law would seem to indicate that the lower lunar gravity (1/6 terrestrial) would result in slower crystal settling on the Moon. However, the viscosity of the silicate melt is the most important factor affecting the settling velocity. The viscosities of typical lunar basaltic melts are 10-100 times less than their terrestrial analogs. These lower viscosities result from two factors: (1) lunar basaltic melts are typically higher in FeO and lower in Al2O3, Na2O, and K2O than terrestrial melts; and (2) lunar igneous melts and phase equilibria tend to be 100-150 C higher than terrestrial, largely because of the general paucity of water and other volatile phases on the Moon. Therefore, particle settling velocities on the Moon are 5-10 times greater than those on Earth. It is highly probable that stratiform ore deposits similar to those on Earth exist on the Moon. The most likely ore minerals involved are chromite, ilmenite, and native FeNi metal. In addition, the greater settling velocities of periodotite in lunar magmas indicate that the buoyancy effects of the melt are less than on Earth. Consequently, the possibility is considerably less than on Earth of deep-seated volcanism transporting upper mantle/lower crustal xenoliths to the surface of the Moon, such as occurs in kimberlites on Earth.

Erosion rate study at the Allchar deposit (Macedonia) based on radioactive and stable cosmogenic nuclides (26 Al, 36 Cl, 3 He, and 21 Ne)

PubMed Central

Cvetković, V.; Niedermann, S.; Pejović, V.; Amthauer, G.; Boev, B.; Bosch, F.; Aničin, I.; Henning, W. F.

2016-01-01

Abstract This paper focuses on constraining the erosion rate in the area of the Allchar Sb‐As‐Tl‐Au deposit (Macedonia). It contains the largest known reserves of lorandite (TlAsS2), which is essential for the LORanditeEXperiment (LOREX), aimed at determining the long‐term solar neutrino flux. Because the erosion history of the Allchar area is crucial for the success of LOREX, we applied terrestrial in situ cosmogenic nuclides including both radioactive (26Al and 36Cl) and stable (3He and 21Ne) nuclides in quartz, dolomite/calcite, sanidine, and diopside. The obtained results suggest that there is accordance in the values obtained by applying 26Al, 36Cl, and 21Ne for around 85% of the entire sample collection, with resulting erosion rates varying from several tens of m/Ma to ∼165 m/Ma. The samples from four locations (L‐8 CD, L1b/R, L1c/R, and L‐4/ADR) give erosion rates between 300 and 400 m/Ma. Although these localities reveal remarkably higher values, which may be explained by burial events that occurred in part of Allchar, the erosion rate estimates mostly in the range between 50 and 100 m/Ma. This range further enables us to estimate the vertical erosion rate values for the two main ore bodies Crven Dol and Centralni Deo. We also estimate that the lower and upper limits of average paleo‐depths for the ore body Centralni Deo from 4.3 Ma to the present are 250–290 and 750–790 m, respectively, whereas the upper limit of paleo‐depth for the ore body Crven Dol over the same geological age is 860 m. The estimated paleo‐depth values allow estimating the relative contributions of 205Pb derived from pp‐neutrino and fast cosmic‐ray muons, respectively, which is an important prerequisite for the LOREX experiment. PMID:27587984

Mineralized aplite—pegmatite at Jabal Sa'id, Hijaz region, Kingdom of Saudi Arabia

NASA Astrophysics Data System (ADS)

Hackett, Damien

The Jabal Sa'id aplite—pegmatite, located at 23°49'03″N, 40°56'30″E, is part of the Jabal Hadb ash Sharar granite complex and resulted from emplacement of a residual volatile-rich fraction of alkali granite magma dominantly above a chilled carapace. Mineralization is layered, with four peak grades in layers 20-25 m wide, one of which may represent a mineral resource with greater potential than the aplite—pegmatite as a whole. The grades of all elements, except Zr, increase towards the upper part of the body. Chemical composition is extremely variable. Major-oxide data confirm previously determined geochemical characteristics and genetic relationships that suggested this body is an apogranite. However, the abundant new data also show that differences between the aplite—pegmatite and cognate alkali microgranite are not as great as previously reported, except for Na 2O which is extremely depleted in the apogranite. REE data support suggested genetic relationships and indicate that feldspar fractionation was important during crystallization. They also show that the content of HREE is comparatively constant throughout the aplite—pegmatite, and that variations in total REE content are caused by variations in the content of LREE. Bastnaesite and synchysite-(Y) are the principal rare-earth-element minerals, and are accompanied by monazite and synchesite; pyrochlore and thorite are also important ore minerals. Other elements concentrated in the aplite—pegmatite, such as Ta, Sn and U, occur only in solid solution in these minerals. The grain size of the ore minerals is commonly in the range 0.02-0.2 mm, and the grain size of gangue minerals, quartz, microcline and lesser amounts of aegirine and arfvedsonite, is typically in the range 1.0-4.0 mm. The ore minerals occur typically along gangue mineral boundaries. Zoning within the body permits calculation of high- and low-grade reserves which correspond to the upper and lower part of the apogranite.

A Search for EUV Emission from the O4f Star Zeta Puppis

NASA Technical Reports Server (NTRS)

Waldron, Wayne L.; Vallerga, John

1996-01-01

We obtained a 140 ks EUVE observation of the O4f star, zeta Puppis. Because of its low ISM column density and highly ionized stellar wind, a unique EUV window is accessible for viewing between 128 to 140 A, suggesting that this star may he the only O star observable with the EUVE. Although no SW spectrometer wavelength bin had a signal to noise greater than 3, a bin at 136 A had a signal to noise of 2.4. This bin is where models predict the brightest line due to OV emission should occur. We present several EUV line emission models. These models were constrained by fitting the ROSAT PSPC X-ray data and our EUVE data. If the OV emission is real, the best fits to the data suggest that there are discrepancies in our current understanding of EUV/X-ray production mechanisms. In particular, the emission measure of the EUV source is found to be much greater than the total wind emission measure, suggesting that the EUV shock must produce a very large density enhancement. In addition, the location of the EUV and X-ray shocks are found to be separated by approx. 0.3 stellar radii, but the EUV emission region is found to be approx. 400 times larger than the X-ray emission region. We also discuss the implications of a null detection and present relevant upper limits.

Re-Os isotopic evidence for an enriched-mantle source for the Noril'sk-type, ore-bearing intrusions, Siberia

USGS Publications Warehouse

Walker, R.J.; Morgan, J.W.; Horan, M.F.; Czamanske, G.K.; Krogstad, E.J.; Fedorenko, V.A.; Kunilov, V.E.

1994-01-01

Magmatic Cu-Ni sulfide ores and spatially associated ultramafic and mafic rocks from the Noril'sk I, Talnakh, and Kharaelakh intrusions are examined for Re-Os isotopic systematics. Neodymium and lead isotopic data also are reported for the ultramafic and mafic rocks. The Re-Os data for most samples indicate closed-system behavior since the ca. 250 Ma igneous crystallization age of the intrusions. There are small but significant differences in the initial osmium isotopic compositions of samples from the three intrusions. Ores from the Noril'sk I intrusion have ??Os values that vary from +0.4 to +8.8, but average +5.8. Ores from the Talnakh intrusion have ??Os values that range from +6.7 to +8.2, averaging +7.7. Ores from the Kharaelakh intrusion have ??Os values that range from +7.8 to +12.9, with an average value of +10.4. The osmium isotopic compositions of the ore samples from the Main Kharaelakh orebody exhibit minimal overlap with those for the Noril'sk I and Talnakh intrusions, indicating that these Kharaelakh ores were derived from a more radiogenic source of osmium than the other ores. Combined osmium and lead data for major orebodies in the three intrusions plot in three distinct fields, indicating derivation of osmium and lead from at least three isotopically distinct sources. Some of the variation in lead isotopic compositions may be the result of minor lower-crustal contamination. However, in contrast to most other isotopic and trace element data, Os-Pb variations are generally inconsistent with significant crustal contamination or interaction with the subcontinental lithosphere. Thus, the osmium and lead isotopic compositions of these intrusions probably reflect quite closely the compositions of their mantle source, and suggest that these two isotope systems were insensitive to lithospheric interaction. Ultramafic and mafic rocks have osmium and lead isotopic compositions that range only slightly beyond the compositions of the ores. These rocks also have relatively uniform ??{lunate}Nd values that range only from -0.8 to + 1.1. This limited variation in neodymium isotopic composition may reflect the characteristics of the mantle sources of the rocks, or it may indicate that somehow similar proportions of crust contaminated the parental melts. The osmium, lead, and neodymium isotopic data for these rocks most closely resemble the mantle sources of certain ocean island basalts (OIB), such as some Hawaiian basalts. Hence, these data are consistent with derivation of primary melts from a mantle source similar to that of some types of hotspot activity. The long-term Re/Os enrichment of this and similar mantle sources, relative to chondritic upper mantle, may reflect 1. (1) incorporation of recycled oceanic crust into the source more than 1 Ga ago, 2. (2) derivation from a mantle plume that originated at the outer core-lower mantle interface, or 3. (3) persistence of primordial stratification of rhenium and osmium in the mantle. ?? 1994.

Accurate localization of organ representation areas on the feet & hands using the bi-digital O-ring test resonance phenomenon: its clinical implication in diagnosis & treatment--Part I.

PubMed

Omura, Y

1994-01-01

Accuracy of the widely used organ representation areas, currently used in different schools of foot and hand reflexology was evaluated using Bi-Digital O-Ring test resonance phenomenon. Our previous study indicated that mapping organ representation areas of the tongue using Bi-Digital O-Ring Test resonance phenomenon between 2 identical substances often provided more reliable clinical information for both diagnosis and treatment than the 2 widely used, but crude, traditional schools of Chinese tongue diagnosis. This same method was applied for the mapping of the organ representation areas on the feet and hands. We succeeded in mapping the following areas on human feet: 1) Middle (3rd) toe on the sole side represents the following starting from the tip: A) Head, B) Face with eye, ear, nose, and mouth (1st Digit) C) Neck and organs within the neck (narrow band of space between 1st crease after the 1st digit and crease at the junction of the beginning of the sole); 2) 2nd and 4th toe represent upper extremities, the beginning tip being fingers and hands. The crease at the base of these toes represents the shoulder. The 2nd toe represents right upper extremity, and the 4th toe represents left upper extremity; 3) 1st and 5th toes in both the right and left feet represent lower extremities with the tip being the toes and soles of feet. The crease at the base of these toes represents the inguinal area. The 1st toe of each foot represents right lower extremity, and 5th toe represents left lower extremity. The sole of the foot is divided into the following 3 distinctive sections. 1) Upper (1st) section represents organs in the chest cavity including 2 thymus glands, trachea, 2 lungs, with the heart between them, and with the esophagus appearing as a narrow band outside of the lung near and below the 1st and 2nd toe depending upon the individual. Chest section occupies the first 1/3 to 1/5 (on a relatively long foot) of the entire sole. The boundary between the chest and G.I. system can be approximately estimated by extending the length of the entire toe or up to 25% longer to the sole, but it can be accurately determined using a diaphragm tissue microscope slide as a reference control substance. 2) Middle (2nd) section represents Gastro-Intestinal system, including lower end of the esophagus, liver, stomach, spleen, gall bladder, pancreas, duodenum, jejunum, ileum, appendix, colon, and anus.(ABSTRACT TRUNCATED AT 400 WORDS)

Phosphorite-hosted zinc and lead mineralization in the Sekarna deposit (Central Tunisia)

USGS Publications Warehouse

Garnit, Hechmi; Bouhel, Salah; Barca, Donatella; Johnson, Craig A.; Chtara, Chaker

2012-01-01

The Sekarna Zn–Pb deposit is located in Central Tunisia at the northeastern edge of the Cenozoic Rohia graben. Mineralization comprises two major ore types: (1) disseminated Zn–Pb sulfides that occur as lenses in sedimentary phosphorite layers and (2) cavity-filling zinc oxides (calamine-type ores) that crosscut Late Cretaceous and Early Eocene limestone. We studied Zn sulfide mineralization in the Saint Pierre ore body, which is hosted in a 5-m-thick sedimentary phosphorite unit of Early Eocene age. The sulfide mineralization occurs as replacements of carbonate cement in phosphorite. The ores comprise stratiform lenses rich in sphalerite with minor galena, Fe sulfides, and earlier diagenetic barite. Laser ablation–inductively coupled plasma mass spectrometry analyses of sphalerite and galena show a wide range of minor element contents with significant enrichment of cadmium in both sphalerite (6,000–20,000 ppm) and galena (12–189 ppm). The minor element enrichments likely reflect the influence of the immediate organic-rich host rocks. Fluid inclusions in sphalerite give homogenization temperatures of 80–130°C. The final ice melting temperatures range from −22°C to −11°C, which correspond to salinities of 15–24 wt.% NaCl eq. and suggest a basinal brine origin for the fluids. Sulfur isotope analyses show uniformly negative values for sphalerite (−11.2‰ to −9.3‰) and galena (−16‰ to −12.3‰). The δ34S of barite, which averages 25.1‰, is 4‰ higher than the value for Eocene seawater sulfate. The sulfur isotopic compositions are inferred to reflect sulfur derivation through bacterial reduction of contemporaneous seawater sulfate, possibly in restricted basins where organic matter was abundant. The Pb isotopes suggest an upper crustal lead source.

Phosphorite-hosted zinc and lead mineralization in the Sekarna deposit (Central Tunisia)

NASA Astrophysics Data System (ADS)

Garnit, Hechmi; Bouhlel, Salah; Barca, Donatella; Johnson, Craig A.; Chtara, Chaker

2012-06-01

The Sekarna Zn-Pb deposit is located in Central Tunisia at the northeastern edge of the Cenozoic Rohia graben. Mineralization comprises two major ore types: (1) disseminated Zn-Pb sulfides that occur as lenses in sedimentary phosphorite layers and (2) cavity-filling zinc oxides (calamine-type ores) that crosscut Late Cretaceous and Early Eocene limestone. We studied Zn sulfide mineralization in the Saint Pierre ore body, which is hosted in a 5-m-thick sedimentary phosphorite unit of Early Eocene age. The sulfide mineralization occurs as replacements of carbonate cement in phosphorite. The ores comprise stratiform lenses rich in sphalerite with minor galena, Fe sulfides, and earlier diagenetic barite. Laser ablation-inductively coupled plasma mass spectrometry analyses of sphalerite and galena show a wide range of minor element contents with significant enrichment of cadmium in both sphalerite (6,000-20,000 ppm) and galena (12-189 ppm). The minor element enrichments likely reflect the influence of the immediate organic-rich host rocks. Fluid inclusions in sphalerite give homogenization temperatures of 80-130°C. The final ice melting temperatures range from -22°C to -11°C, which correspond to salinities of 15-24 wt.% NaCl eq. and suggest a basinal brine origin for the fluids. Sulfur isotope analyses show uniformly negative values for sphalerite (-11.2‰ to -9.3‰) and galena (-16‰ to -12.3‰). The δ34S of barite, which averages 25.1‰, is 4‰ higher than the value for Eocene seawater sulfate. The sulfur isotopic compositions are inferred to reflect sulfur derivation through bacterial reduction of contemporaneous seawater sulfate, possibly in restricted basins where organic matter was abundant. The Pb isotopes suggest an upper crustal lead source.

Host-rock controlled epigenetic, hydrothermal metasomatic origin of the Bayan Obo REEFe-Nb ore deposit, Inner Mongolia, P.R.C.

USGS Publications Warehouse

Chao, E.C.T.; Back, J.M.; Minkin, J.A.; Yinchen, R.

1992-01-01

Bayan Obo, a complex rare earth element (REE)FeNb ore deposit, located in Inner Mongolia, P.R.C. is the world's largest known REE deposit. The deposit is chiefly in a marble unit (H8), but extends into an overlying unit of black shale, slate and schist unit (H9), both of which are in the upper part of the Middle Proterozoic Bayan Obo Group. Based on sedimentary structures, the presence of detrital quartz and algal fossil remains, and the 16-km long geographic extent, the H8 marble is a sedimentary deposit, and not a carbonatite of magmatic origin, as proposed by some previous investigators. The unit was weakly regionally metamorphosed (most probably the lower part of the green schist facies) into marble and quartzite prior to mineralization. Tectonically, the deposit is located on the northern flank of the Sino-Korean craton. Many hypotheses have been proposed for the origin of the Bayan Obo deposit; the studies reported here support an epigenetic, hydrothermal, metasomatic origin. Such an origin is supported by field and laboratory textural evidence; 232Th/208Pb internal isochron mineral ages of selected monazite and bastnaesite samples; 40Ar/39Ar incremental heating minimum mineral ages of selected alkali amphiboles; chemical compositions of different generations of both REE ore minerals and alkali amphiboles; and evidence of host-rock influence on the various types of Bayan Obo ores. The internal isochron ages of the REE minerals indicate Caledonian ages for various episodes of REE and Fe mineralization. No evidence was found to indicate a genetic relation between the extensive biotite granitic rocks of Hercynian age in the mine region and the Bayan Obo are deposit, as suggested by previous workers. ?? 1992.

Great Lakes/St. Lawrence Seaway Regional Transportation Study; Great Lakes Area Industries.

DTIC Science & Technology

1981-11-01

integrated mill at Nanticoke on Lake Erie , directly north of Erie , Pennsylvania . Almost all iron ore is received at these plants by water. 111-23II Ia...Generating Co. Decker, MT 613 Presque Isle Plant (MI) Absaloka, MT 307 Roseloud, MT 307 Pevler, KY 301 Wolverine, KY 192 All Sources 2120 Note...Pub. Works Holland, MI 160 Grand Haven Bd. of L&P Grand Haven, MI 90 Marquette Bd. of L&P Marquette, MI 125 Upper Penin. Gen. Co. Presque Isle

Dzhezkazgan and associated sandstone copper deposits of the Chu-Sarysu basin, Central Kazakhstan

USGS Publications Warehouse

Box, Stephen E.; Seltmann, Reimar; Zientek, Michael L.; Syusyura, Boris; Creaser, Robert A.; Dolgopolova, Alla

2012-01-01

Sandstone-hosted copper (sandstone Cu) deposits occur within a 200-km reach of the northern Chu-Sarysu basin of central Kazakhstan (Dzhezkazgan and Zhaman-Aibat deposits, and the Zhilandy group of deposits). The deposits consist of Cu sulfide minerals as intergranular cement and grain replacement in 10 ore-bearing members of sandstone and conglomerate within a 600- to 1,000-m thick Pennsylvanian fluvial red-bed sequence. Copper metal content of the deposits ranges from 22 million metric tons (Mt, Dzehzkazgan) to 0.13Mt (Karashoshak in the Zhilandy group), with average grades of 0.85 to 1.7% Cu and significant values for silver (Ag) and rhenium (Re). Broader zones of iron reduction (bleaching) of sandstones and conglomerates of the red-bed sequence extend over 10 km beyond each of the deposits along E-NE-trending anticlines, which began to form in the Pennsylvanian. The bleached zones and organic residues within them are remnants of ormer petroleum fluid accumulations trapped by these anticlines. Deposit sites along these F1anticlines are localized at and adjacent to the intersections of nearly orthogonal N-NW-trending F2synclines. These structural lows served to guide the flow of dense ore brines across the petroleum-bearing anticlines, resulting in ore sulfide precipitation where the two fluids mixed. The ore brine was sourced either from the overlying Early Permian lacustrine evaporitic basin, whose depocenter occurs between the major deposits, or from underlying Upper Devonian marine evaporites. Sulfur isotopes indicate biologic reduction of sulfate but do not resolve whether the sulfate was contributed from the brine or from the petroleum fluids. New Re-Os age dates of Cu sulfides from the Dzhezkazgan deposit indicate that mineralization took place between 299 to 309 Ma near the Pennsylvanian-Permian age boundary. At the Dzhezkazgan and some Zhilandy deposits, F2fold deformation continued after ore deposition. Copper orebodies in Lower Permian shale near the Zhaman-Aibat deposit indicate that at least some of the mineralization there is younger than at Dzhezkazgan, consistent with the Re-Os age and with differences in their ore Pb isotopes.

Potash ore reserves in the proposed Waste Isolation Pilot Plant area, Eddy County, southeastern New Mexico

USGS Publications Warehouse

John, Charles B.; Cheeseman, R.J.; Lorenz, J.C.; Millgate, M.L.

1978-01-01

The proposed Waste Isolation Pilot Plant (WIPP) area includes about 18,960 acres in Tps. 22 and 23 S., Rs. 30 and 31 E., New Mexico Principal Meridian, Eddy County, southeastern New Mexico. It is located within the Carlsbad Mining District about 25 miles east of Carlsbad. The WIPP area is immediately south of the Capitan Limestone subcrop, which formed the northern margin of the Delaware basin in Permian time. During Late Permian (Ochoan) time, gypsum, anhydrite, and halite were deposited in the seas of the Delaware basin to form the Castile Formation. These deposits have a maximum thickness of about 2,000 feet and grade upward into the more argillaceous beds of the Salado Formation. The Salado Formation contains abundant sulfate minerals, notably anhydrite and polyhalite. The potash ore minerals, langbeinite and sylvite, occur in the upper part of the Salado Formation in the McNutt potash zone, a local name applied to a potassium-rich zone.

Les amas sulfurés du massif miocène d'El Aouana (Algérie)— I. Dynamisme de mise en place des roches volcaniques et implications métallogéniques

NASA Astrophysics Data System (ADS)

Villemaire, Cl.

Two main units have been distinguished in the Miocene El Aouana area. A tectonic event occurs between their respective deposits inducing faulting, tilting of the lower volcanic unit and caldeira structure. The lower unit comprises first continental air fall pyroclastic rocks and dacitic flows, then marine flow pyroclastic rocks, dacitic flows and epiclastic rocks. The upper volcanic unit, announced by extensive andesitic flows, is characterized by pyroclastic flow sheets. The two units are intruded by dacitic domes. These volcanic rocks belong to the calco-alcaline succession, with well-expressed acidic terms. The ore deposits are formed by lenses, stockworks and lodes. They are massive sulphides ore type. Mineralizations are strictly localized at the contact boundary between dacitic intrusive rocks and marine pyroclastic flows and epiclastic rocks. We suggest that the systematic research of dacitic domes would be successful to increase the mining reserves of this area.

The Influence of the Ufimian Tectonic Concentric Structure on the Hydrocarbon Migration and Ore Genesis

NASA Astrophysics Data System (ADS)

Filippov, V. A.

2018-01-01

The Ufimian tectonic concentric structure (UTC) is a regional structure with concentric and zonal structure of the internal gravity field. In the Neoproterozoic this structure was at higher hypsometric level relative to the Bashkir Meganticlinorium. The most significant uplift of this tectonic concentric structure happened at the beginning of the Karatau time ( 825 Ma) and was accompanied by the formation of a ring fractured zone, favorable for hydrocarbon migration from the Lower Riphean black shales. Due to this, bitumens with higher Mo content in the Neoproterozoic and Paleozoic deposits are confined spatially to this zone. The bitumenosity of the Neoproterozoic deposits on the southern slope of the Ufimian tectonic concentric structure could have contributed to the formation of complex Cu-Ag-Mo-Re ores (copper sands) at the upper boundary of terrigenous red deposits of the Zilmerdak Formation. Positive structures identified in the Neoproterozoic deposits near the margin of the Ufimian tectonic concentric structure are considered to be promising for searching for hydrocarbon fields.

Orogenesis, high-T thermal events, and gold vein formation within metamorphic rocks of the Alaskan Cordillera

USGS Publications Warehouse

Goldfarb, R.J.; Snee, L.W.; Pickthorn, W.J.

1993-01-01

Mesothermal, gold-bearing quartz veins are widespread within allochthonous terranes of Alaska that are composed dominantly of greenschist-facies metasedimentary rocks. The most productive lode deposits are concentrated in south-central and southeastern Alaska; small and generally nonproductive gold-bearing veins occur upstream from major placer deposits in interior and northern Alaska. Ore-forming fluids in all areas are consistent with derivation from metamorphic devolatilisation reactions, and a close temporal relationship exists between high-T tectonic deformation, igneous activity, and gold mineralization. Ore fluids were of consistently low salinity, CO2-rich, and had ??18O values of 7 ???-12??? and ??D values between -15??? and -35???. Upper-crustal temperatures within the metamorphosed terranes reached at least 450-500??C before onset of significant gold-forming hydrothermal activity. In southern Alaska, gold deposits formed during latter stages of Tertiary, subduction-related, collisional orogenesis and were often temporally coeval with calc-alkaline magmatism. -from Authors

Consistency Check for the Bin Packing Constraint Revisited

NASA Astrophysics Data System (ADS)

Dupuis, Julien; Schaus, Pierre; Deville, Yves

The bin packing problem (BP) consists in finding the minimum number of bins necessary to pack a set of items so that the total size of the items in each bin does not exceed the bin capacity C. The bin capacity is common for all the bins.

Localization of uranium minerals in channel sediments at the base of the Shinarump conglomerate, Monument Valley, Arizona

USGS Publications Warehouse

Witkind, I.J.

1954-01-01

formation (Permian) to the Salt Wash member of the Morrison formation (Jurassic), The dominant structural element of the area is the Monument upwarp, a arge asymmetrical anticline whose northern end is near the junction of the Green and Colorado Rivers in Utah, and whose southern end disappears near Kayenta, Ariz. Asymmetrical anticlines with steeply dipping east flanks and gently dipping west flanks are superimposed on the upwarp. These subsidiary structures trend north. The uranium ore bodies are localized in conglomeratic sandstone of the Upper Triassic Shinarump conglomerate that fills channels scoured in the underlying Lower and Middle (?) Triassic Moenkopi formation. These channels range from relatively narrow and shallow ones 15 feet wide and 10 feet deep to much broader and deeper ones 2,300 feet wide and 70 feet deep. Two types of channels can be distinguished-r-a short-type less than 2 miles Iong 5 and a long-type traceable for distances greater than 2 miles Plant matter in the form of trees, branches,'and twigs was deposited with Shinarump sediments in the channels. It is suggested that when the Shinarump conglomerate was invaded by mineralizing solutions the uranium ore was deposited primarily in localities formerly occupied by the plant material. Further, it is suggested that the short channels are more likely to have ore accumulations than long channels.

Comparison of recycling outcomes in three types of recycling collection units.

PubMed

Andrews, Ashley; Gregoire, Mary; Rasmussen, Heather; Witowich, Gretchen

2013-03-01

Commercial institutions have many factors to consider when implementing an effective recycling program. This study examined the effectiveness of three different types of recycling bins on recycling accuracy by determining the percent weight of recyclable material placed in the recycling bins, comparing the percent weight of recyclable material by type of container used, and examining whether a change in signage increased recycling accuracy. Data were collected over 6 weeks totaling 30 days from 3 different recycling bin types at a Midwest University medical center. Five bin locations for each bin type were used. Bags from these bins were collected, sorted into recyclable and non-recyclable material, and weighed. The percent recyclable material was calculated using these weights. Common contaminates found in the bins were napkins and paper towels, plastic food wrapping, plastic bags, and coffee cups. The results showed a significant difference in percent recyclable material between bin types and bin locations. Bin type 2 was found to have one bin location to be statistically different (p=0.048), which may have been due to lack of a trash bin next to the recycling bin in that location. Bin type 3 had significantly lower percent recyclable material (p<0.001), which may have been due to lack of a trash bin next to the recycling bin and increased contamination due to the combination of commingled and paper into one bag. There was no significant change in percent recyclable material in recycling bins post signage change. These results suggest a signage change may not be an effective way, when used alone, to increase recycling compliance and accuracy. This study showed two or three-compartment bins located next to a trash bin may be the best bin type for recycling accuracy. Copyright © 2012 Elsevier Ltd. All rights reserved.

Geochronology, geochemistry and isotope tracing of the Oligocene magmatism of the Buchim-Damjan-Borov Dol ore district: Implications for timing, duration and source of the magmatism

NASA Astrophysics Data System (ADS)

Lehmann, St.; Barcikowski, J.; von Quadt, A.; Gallhofer, D.; Peytcheva, I.; Heinrich, C. A.; Serafimovski, T.

2013-11-01

Timing, source and magmatic evolution of the intrusions in the Buchim-Damjan-Borov Dol ore district of the Former Yugoslav Republic of Macedonia (F.Y.R.O.M.) have been studied. They intrude the Circum Rhodope Unit close to the contact with the Vardar Zone and are a part of the Late Eocene-Oligocene Macedonian Rhodope-North Aegean belt. The magmatism at Buchim-Damjan-Borov Dol occurred between 24.04 ± 0.77 and 24.51 ± 0.89 Ma, as indicated by chemical-annealing (CA)-LA ICP-MS zircon dating. Major element, trace and rare earth element analyses have been performed on the various intrusive rocks. All ore bearing magmas were classified as trachyandesitic, except the youngest intrusion which is not associated with mineralization; the Black Hill locality (24.04 ± 0.77 Ma) shows a trachytic composition. The distribution of the trace elements, enrichment of large ion lithophile elements (LILE) and depletion in high field strength elements (HFSE), indicates subduction-related magmatism; most of the magmas follow a calc-alkaline fractionation trend with shoshonitic affinities; additionally, Sr/Y (10 to 90) and La/Yb values show some similarities to adakite-like magmas. Sr and Nd isotope ratios (Sri = 0.70658 to 0.70740 and Ndi = 0.512425-0.512497) show that the magmatic products were slightly contaminated by continental crust material, e.g., the Variscan/Cadomian basement. In the Late Eocene-Oligocene belt the magmatism between 29 and 35 Ma is dominated by crustal melting with an increase in the mantle contribution between 20 and 27 Ma. We suggest the following scenario for the magmatic history of the Buchim-Damjan-Borov Dol ore district: a slab rollback of an oceanic slab located further to the SW which led to extensional and compressional features in upper levels of the continental crust. In the middle to upper crust three consecutive crystallization stages occurred at variable depths as indicated by amphibole zonation. Mixing of newly formed crust with mantle-like affinities and continental crust material in variable degrees during the ascent of the magma can explain all geochemical characteristics. The magma crystallized as dykes or stocks near the Earth's surface (> 1 km) after its final emplacement and contemporaneous hydrothermal activity led to different mineralization styles depending on the lithology of the host rocks.

Halo independent comparison of direct dark matter detection data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gondolo, Paolo; Gelmini, Graciela B., E-mail: paolo@physics.utah.edu, E-mail: gelmini@physics.ucla.edu

We extend the halo-independent method of Fox, Liu, and Weiner to include energy resolution and efficiency with arbitrary energy dependence, making it more suitable for experiments to use in presenting their results. Then we compare measurements and upper limits on the direct detection of low mass ( ∼ 10 GeV) weakly interacting massive particles with spin-independent interactions, including the upper limit on the annual modulation amplitude from the CDMS collaboration. We find that isospin-symmetric couplings are severely constrained both by XENON100 and CDMS bounds, and that isospin-violating couplings are still possible at the lowest energies, while the tension of themore » higher energy CoGeNT bins with the CDMS modulation constraint remains. We find the CRESST-II signal is not compatible with the modulation signals of DAMA and CoGeNT.« less

Numerical simulation on the deformation and failure of the goaf surrounding rock in Heiwang mine

NASA Astrophysics Data System (ADS)

Shang, Yandong; Guo, Yanpei; Zhang, Wenquan

2018-02-01

The stability of overlying rock mass of mined-out area was simulated using finite difference software FLAC3D according to the gob distribution of Heiwang iron mine. The deformation, failure characteristics of surrounding rock was obtained. The subsidence of strata above the middle mined-out area was the biggest. The maximum subsidence of ground surface was 12.4mm. The farther away from the central goaf was, the smaller the vertical subsidence value was. There was almost no subsidence on the two lateral surrounding rock near mined-out area. There exists the potential danger when cutting along the boundary of goaf. The tensile stress appeared at the top and bottom of the mined-out area. The maximum of tensile stress was 34.7kPa. There was the compressive stress concentration phenomenon in the lateral boundary of mined-out area. The stress concentration coefficient was about 1.5 on both sides of gob. The upper section of the middle goaf was subjected to the tensile failure, and the upper rock mass of both sides was mainly subjected to the tensile-shear failure. The ore pillars on the inner side of the goaf were mainly subjected to the shear failure. When the overlying strata were complete, the possibility of sudden instability of the ore pillar and the sudden subsidence of the ground surface could not occur. The achievements can provide theoretical basis for the processing of the goaf.

Geology and ore deposits of the Pioche district, Nevada

USGS Publications Warehouse

Westgate, L.G.; Knopf, Adolph

1932-01-01

LOCATION AND SURFACE FEATURES The Bristol Range, Highland, and Ely Range quadrangles make up the larger part of a. rectangular area 35 miles north and south by 24 miles east and west, which lies 19 miles west of the Nevada-Utah line and about 250 miles southwest of Salt Lake City. The district lies within the Great Basin, a semiarid region of alternating mountain ranges and intermontane plains floored largely by outwash from the mountains. The plain, which slopes away from the ranges, stands between 4,700 and 6,000 feet above the sea. The Bristol and Highland Ranges, which are separated only by a low gap, form an almost continuous north-south range that rises about 2,500 feet above the highest part of the surrounding plain, to general altitudes of 8,000 to 9,000 feet, though the highest point, Highland Peak, reaches 9,395 feet. A lower range, the Ely Range, with a northwesterly trend, lies farther east and nearly in touch with the Bristol-Highland Range. The town of Pioche lies midway on the. eastern foot of the Ely Range. ROOKS OF THE PIOOHB REGION The rocks of the ranges are Paleozoic sediments, Tertiary (?) lavas and intrusive rocks, and Pliocene (?) tuffs. The Paleozoic sediments have a total thickness of nearly 18,000 feet. Over 8,000 feet of the Cambrian has been measured without reaching its base. The lowest Cambrian formation is a quartzite, of which only the upper 1,500 feet is exposed, and this is followed by 1,200 feet of shale, 400 feet of limestone, aoid 150 feet of shale. Above this second shale the upper three-fourths of the Cambrian consists of limestone and dolomitic limestone. It is in the quartzite and in the limestone interbedded in and bounding the shales that the main ore bodies of the district have been found. Above the Cambrian comes 1,795 feet of Ordovician limestone, with some interbedded dolomite and with a 50-foot quartzite a, third of the way down from the top; 75 feet of Silurian dolomite; 3,000 feet of Middle Devonian dolomite with thin interbedded quartzite near the top, followed by 550 feet of Upper Devonian limestone; 3,775 feet of Mississippian limestone with a heavy quartzitic sandstone just below the middle; then, at the top of the series, 700 feet of Pennsylvania n limestone.The Paleozoic formations are tilted, bent, and faulted, but sharp folding is extremely rare. Dips between 10° and 30° are common, but there are few greater than 40°. The rocks are cut by many large and innumerable small normal faults, which in many parts of the area are difficult to recognize because they cut thick formations of similar rocks. A large thrust fault occurs along the west side of the Bristol-Highland Range. A thick series of lavas with interbedded tuffs lies along the flanks of the ranges and makes up a large part of the hilly northwest corner of the Bristol quadrangle. The lavas lie unconformably on the Paleozoic sediments and consist mainly of dacite, latite, and andesite, with some basalt and a little rhyolite. About 6,000 feet of lavas and tuffs were measured in Condor Canyon, near the south end of the Ely Range. The age of the lavas is not sharply fixed; they may be early Tertiary or even late Mesozoic. It is not unlikely that they are the result of volcanic action extending over a long period. The lavas are tilted and faulted, though their average dip is less than that of the Paleozoic sediments. At Blind Mountain, on the west side of the Bristol Range, stocks of quartz monzonite and dikes of similar composition cut an infaulted block consisting of sediments, chiefly Devonian, and lavas. Both the sediments and the lavas are metamorphosed, and a belt of marked metamorphism extends south along the west base of the Bristol-Highland Range for several miles. The quartz porphyry dikes of the region, including those near Pioche, are believed to have come in at the same time. The plain west of the Bristol-Highland Range is a. valley of interior drainage floored with outwash from the mountains, coarser near the range but finer and making a clay flat along the west side of the Bristol Range and Highland quadrangles. The valley east of the Bristol-Highland Range, however, has outside drainage by way of Meadow Valley to the Virgin and Colorado Rivers. The stream in upper Meadow Valley and its tributaries have cut through the surface wash from the mountains and laid bare several hundred feet of white, yellow, and red water-laid Pliocene tuffs that lie in nearly the position in which they were laid down. This erosion has developed a striking badland topography in the Pliocene beds. HISTORICAL SUMMARY The general succession of events may be summarized as follows: 1. Sedimentation during most of Paleozoic time from Cambrian to Pennsylvanian. 2. Uplift, slight warping, and erosion. 3. Volcanism of perhaps late Mesozoic or early Tertiary time, producing lavas and tuffs. This period of volcanism may have lasted a long time and spanned one or more of the epochs of faulting. 4. Tilting and normal faulting. 5. Thrust faulting. 6. Quartz monzonite intrusions at Blind Mountain. 7. Normal block faulting of the Basin Range type. 8. Erosion of the faulted blocks to maturity and to essen-. tially the topography of to-day. 9. Outbursts of volcanic ash, probably in late Pliocene time, and the deposition of several hundred feet of water-laid tuffs in the valleys. 10. In Meadow Valley, valley cutting, which has produced a badland topography in the soft Pliocene tuffs and canyons where the streams cross the harder Paleozoic limestones. ECONOMIC GEOLOGY The Pioche district during four years in the early seventies was second only to the Comstock district in output of silver. The bonanza ore of those stirring times came from fissure veins in the Prospect Mountain quartzite, of Lower Cambrian age. In recent years the main interest has shifted to the bedded replacement deposits of silver-bearing lead-zinc sulphide ore occurring in the limestone members of the Pioche shale a type of ore body which was discovered accidentally during the prospecting of the fissure veins. The ore deposits of the district comprise three groups (1) silver-bearing fissure veins in quartzite; (2) silver-bearing mineralized granite porphyry; (3) replacement deposits in limestone and dolomite. All of them appear to have been formed at about the same time, in the epoch of mineralization that occurred shortly after the intrusion of the granitic rocks and their allied dikes of granite porphyry and lamprophyre. The entire present output of the district is coming from the replacement deposits in limestone and dolomite, but exploratory work is still in progress on the fissure veins and mineralized porphyry. The replacement deposits include both replacement fissure veins and stratiform ("bedded") replacement deposits. The replacement fissure veins dip steeply and cut across the bedding of the carbonate rocks in which they are inclosed. They are thoroughly oxidized, as deep at least as 1,100 feet, for on none of them have the mine workings penetrated to water level, and they are highly manganiferous and limonitic and low in silica. At-certain horizons stratiform replacement deposits extend out as lateral branches from the fissure veins. Deposits of this kind occur mainly in the Mendha limestone, Highland Peak limestone, and Lyndon limestone. The stratigraphic range is therefore at least 5,500 feet, and as some of the fissure veins extend down through the underlying Pioche shale the indicated range may exceed 6,500 feet. The most notable representatives of the replacement fissure veins are at the Bristol mine, where they yield silver-bearing copper-leadzinc ores. So far unique among the ore bodies of the district is the pipe of wad and pyrolusite ore at the Jackrabbit mine, the periphery of the pipe consisting of a girdle of extraordinarily coarse white calcite spar produced by the recrystallization of the surrounding limestones. The stratiform replacement deposits that are attracting most attention occur at the intersections of steep fissures with the limestone members of the Pioche shale. In recent years the " bedded " ore of the Combined Metals mine has been of main interest. The ore is essentially a.n intimate intergrowth of pyrite, sphalerite, and galena. Although above water level, the ore is unoxidized. It extends on both sides of the mineralizing fissure as far as 100 feet. At the Prince mine ore beds were formed at seven successively higher horizons in the Pioche shale and the overlying Lyndon and Highland Peak limestones. The ore " beds " above water level in the Prince mine are thoroughly oxidized and consist of manganese-iron oxides low in silver, lead, and zinc. About 800,000 tons of ore carrying 2.5 to 3 ounces of silver to the ton, 3 per cent of lead, 35 per cent of iron, and 15 per cent of manganese has been shipped. The Prince mine was in 1915-1918 the premier producer of lead in Nevada. The ore " bed " that occurs here below water level consists of sphalerite, galena, and pyrite in a gangue of manganosiderite and minor quartz. This is the only locality in the district in which the primary source of the abundant oxidized manganese minerals (wad, pyrolusite, and braunite) has so far been found. Some of the stratiform ore bodies the ore beds, as they are locally called were formed adjacent to exceedingly insignificant-looking fissures; and this dependence on inconspicuous mineralizing fissures is beyond doubt one of the most impressive features in the geology of the district. It opens the possibility that there may be many other bedded deposits which, like the Combined Metals ore bed, do not crop out. To find these ore bodies will be difficult, but their discovery will be aided primarily by applying skillfully a knowledge of the geologic column and by determining the faulting that has disturbed or changed the normal sequence of the strata.

A deposit model for magmatic iron-titanium-oxide deposits related to Proterozoic massif anorthosite plutonic suites

USGS Publications Warehouse

Woodruff, Laurel G.; Nicholson, Suzanne W.; Fey, David L.

2013-01-01

This descriptive model for magmatic iron-titanium-oxide (Fe-Ti-oxide) deposits hosted by Proterozoic age massif-type anorthosite and related rock types presents their geological, mineralogical, geochemical, and geoenvironmental attributes. Although these Proterozoic rocks are found worldwide, the majority of known deposits are found within exposed rocks of the Grenville Province, stretching from southwestern United States through eastern Canada; its extension into Norway is termed the Rogaland Anorthosite Province. This type of Fe-Ti-oxide deposit dominated by ilmenite rarely contains more than 300 million tons of ore, with between 10- to 45-percent titanium dioxide (TiO2), 32- to 45-percent iron oxide (FeO), and less than 0.2-percent vanadium (V). The origin of these typically discordant ore deposits remains as enigmatic as the magmatic evolution of their host rocks. The deposits clearly have a magmatic origin, hosted by an age-constrained unique suite of rocks that likely are the consequence of a particular combination of tectonic circumstances, rather than any a priori temporal control. Principal ore minerals are ilmenite and hemo-ilmenite (ilmenite with extensive hematite exsolution lamellae); occurrences of titanomagnetite, magnetite, and apatite that are related to this deposit type are currently of less economic importance. Ore-mineral paragenesis is somewhat obscured by complicated solid solution and oxidation behavior within the Fe-Ti-oxide system. Anorthosite suites hosting these deposits require an extensive history of voluminous plagioclase crystallization to develop plagioclase-melt diapirs with entrained Fe-Ti-rich melt rising from the base of the lithosphere to mid- and upper-crustal levels. Timing and style of oxide mineralization are related to magmatic and dynamic evolution of these diapiric systems and to development and movement of oxide cumulates and related melts. Active mines have developed large open pits with extensive waste-rock piles, but because of the nature of the ore and waste rock, the major environmental impacts documented at the mine sites are reported to be waste disposal issues and somewhat degraded water quality.

The origin of the Tongkeng-Changpo tin deposit, Dachang metal district, Guangxi, China: clues from fluid inclusions and He isotope systematics

NASA Astrophysics Data System (ADS)

Minghai, Cai; Jingwen, Mao; Ting, Liang; Pirajno, Franco; Huilan, Huang

2007-08-01

Tongkeng-Changpo is the largest tin deposit within the giant Dachang polymetallic tin ore field in Guangxi, southern China, which is part of a large skarn system associated with Cretaceous granitoids. The Tongkeng-Changpo mineralization consists of veins and stockworks in the upper levels and replacement stratiform orebodies (mantos) at lower levels. Based on textural relationships, three major mineralizing stages can be recognized: stage I with cassiterite, sulphides, stannite, tourmaline, and quartz; stage II with cassiterite, sulphides, sulphosalts, quartz, and calcite; and stage III with calcite as the main phase. The study of fluid inclusions has shown that there are two main fluid types: CO2 and NaCl-H2O. Homogenization temperatures are 270 to 365°C, 210 to 240°C, and 140 to 190°C for stages I, II, and III, respectively. Salinities range from 1 to 7 wt.% NaCl equiv. in the early ore stage and 3 to 10 wt.% NaCl equiv. in the late stages. Laser Raman Spectroscopy indicates that the inclusion fluids in stages I and II were of carbono-aqueous composition, with minor amounts of CH4 and H2S, whereas those in stage III were aqueous. Helium isotopic analyses of inclusion fluids indicate that the 3He/4He ratios in the ore veins are in between 1.2 to 2.9 Ra (Ra = 1.4 × 10-6, modern atmospheric ratio), and range from 1.6 to 2.5 Ra in the stratiform orebodies. This range of 3He/4He ratios is significantly higher than that of crustal fluids (0.01-0.05 Ra). The similar characteristics of fluid inclusions and their He isotopic composition, as well as age constraints, indicate that the ore veins and stratiform orebodies of the Tongkeng-Changpo deposit formed from the same hydrothermal system, likely related to granite intrusions of the Mesozoic Yanshanian tectono-thermal event. In addition, the high R/Ra ratios indicate a mantle contribution in the ore fluids.

Augmented neural networks and problem structure-based heuristics for the bin-packing problem

NASA Astrophysics Data System (ADS)

Kasap, Nihat; Agarwal, Anurag

2012-08-01

In this article, we report on a research project where we applied augmented-neural-networks (AugNNs) approach for solving the classical bin-packing problem (BPP). AugNN is a metaheuristic that combines a priority rule heuristic with the iterative search approach of neural networks to generate good solutions fast. This is the first time this approach has been applied to the BPP. We also propose a decomposition approach for solving harder BPP, in which subproblems are solved using a combination of AugNN approach and heuristics that exploit the problem structure. We discuss the characteristics of problems on which such problem structure-based heuristics could be applied. We empirically show the effectiveness of the AugNN and the decomposition approach on many benchmark problems in the literature. For the 1210 benchmark problems tested, 917 problems were solved to optimality and the average gap between the obtained solution and the upper bound for all the problems was reduced to under 0.66% and computation time averaged below 33 s per problem. We also discuss the computational complexity of our approach.

Octree Bin-to-Bin Fractional-NTC Collisions

DTIC Science & Technology

2015-09-17

Briefing Charts 3. DATES COVERED (From - To) 24 August 2015 – 17 September 2015 4. TITLE AND SUBTITLE Octree bin-to-bin fractional -NTC collisions...Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 OCTREE BIN-TO-BIN FRACTIONAL -NTC COLLISIONS Robert Martin ERC INC., SPACECRAFT PROPULSION...AFTC/PA clearance No. TBD ROBERT MARTIN (AFRL/RQRS) DISTRIBUTION A: APPROVED FOR PUBLIC RELEASE 1 / 15 OUTLINE 1 BACKGROUND 2 FRACTIONAL COLLISIONS 3 BIN

Genesis of the Bangbule Pb-Zn-Cu polymetallic deposit in Tibet, western China: Evidence from zircon U-Pb geochronology and S-Pb isotopes

NASA Astrophysics Data System (ADS)

Kan, Tian; Zheng, Youye; Gao, Shunbao

2016-04-01

The Banbule Pb-Zn-Cu skarn deposit is located in the Longger-Gongbujiangda volcanic magma arc in the Gangdese-Nyainqentanglha Plate. It is the only lead-zinc polymetallic deposit discovered in the westernmost Nyainqentanglha metallogenic belt. The measured and indicated resources include 0.9 Mt of Pb+Zn (4.77% Pb and 4.74% Zn, respectively), 6499 t of Cu, and 178 t of Ag (18.75g/t Ag). The orebodies mainly occur as lenses, veins and irregular shapes in the contact zone between the quartz-porphyry and limestone of the Upper Permian Xiala Formation, or in the boundaries between limestone and sandstone. Pb-Zn-Cu mineralization in the Banbule deposit is closely associated with skarns. The ore minerals are dominated by galena, sphalerite, chalcopyrite, bornite, and magnetite, with subordinate pyrite, malachite, and azurite. The gangue minerals are mainly garnet, actinolite, diopside, quartz, and calcite. The ore-related quartz-porphyry displays LA-ICP-MS zircon U-Pb age of 77.31±0.74 Ma. The δ34S values of sulfides define a narrow range of -0.8 to 4.7‰ indicating a magmatic source for the ore-forming materials. Lead isotopic systematics yield 206Pb/204Pb of 18.698 to 18.752, 207Pb/204Pb of 15.696 to 15.760, and 208Pb/204Pb of 39.097 to 39.320. The data points are constrained around the growth curves of upper crust and orogenic belt according to the tectonic discrimination diagrams. The calculated Δβ - Δγ values plot within the magmatic field according to the discrimination diagram of Zhu et al. (1995). The S-Pb isotopic data suggest that Bangbule is a typical skarn deposit, and the Pb-Zn-Cu mineralization is genetically related to the quartz-porphyry in the mining district. The discovery of the Bangbule deposit indicates that there is metallogenic potential in the westernmost Nyainqentanglha belt, which is of great importance for the exploration work in this area.

Variations of trace element concentration of magnetite and ilmenite from the Taihe layered intrusion, Emeishan large igneous province, SW China: Implications for magmatic fractionation and origin of Fe-Ti-V oxide ore deposits

NASA Astrophysics Data System (ADS)

She, Yu-Wei; Song, Xie-Yan; Yu, Song-Yue; He, Hai-Long

2015-12-01

In situ LA-ICP-MS trace elemental analysis has been applied to magnetite and ilmenite of the Taihe layered intrusion, Emeishan large igneous province, SW China, in order to understand better fractionation processes of magma and origin of Fe-Ti-V oxide ore deposits. The periodic reversals in Mg, Ti, Mn in magnetite and Mg, Sc in ilmenite are found in the Middle Zone of the intrusion and agree with fractionation trends as recorded by olivine (Fo), plagioclase (An) and clinopyroxene (Mg#) compositions. These suggest the Taihe intrusion formed from open magma chamber processes in a magma conduit with multiple replenishments of more primitive magmas. The V and Cr of magnetite are well correlated with V and Cr of clinopyroxene indicating that they became liquidus phases almost simultaneously at an early stage of magma evolution. Ilmenite from the Middle and Upper Zones shows variable Cr, Ni, V, Mg, Nb, Ta and Sc contents indicating that ilmenite at some stratigraphic levels crystallized slightly earlier than magnetite and clinopyroxene. The early crystallization of magnetite and ilmenite is the result of the high FeOt and TiO2 contents in the parental magma. The ilmenite crystallization before magnetite in the Middle and Upper Zones can be attributed to higher TiO2 content of the magma due to the remelting of pre-existing ilmenite in a middle-level magma chamber. Compared to the coeval high-Ti basalts, the relatively low Zr, Hf, Nb and Ta contents in both magnetite and ilmenite throughout the Taihe intrusion indicate that they crystallized from Fe-Ti-(P)-rich silicate magmas. Positive correlations of Ti with Mg, Mn, Sc and Zr of magnetite, and Zr with Sc, Hf and Nb of ilmenite also suggest that magnetite and ilmenite crystallized continuously from the homogeneous silicate magma rather than an immiscible Fe-rich melt. Therefore, frequent replenishments of Fe-Ti-(P)-rich silicate magma and gravitational sorting and settling are crucial for the formation the massive and apatite-rich disseminated ores in the Lower and Middle Zones of the Taihe intrusion.

optBINS: Optimal Binning for histograms

NASA Astrophysics Data System (ADS)

Knuth, Kevin H.

2018-03-01

optBINS (optimal binning) determines the optimal number of bins in a uniform bin-width histogram by deriving the posterior probability for the number of bins in a piecewise-constant density model after assigning a multinomial likelihood and a non-informative prior. The maximum of the posterior probability occurs at a point where the prior probability and the the joint likelihood are balanced. The interplay between these opposing factors effectively implements Occam's razor by selecting the most simple model that best describes the data.

Chemical and physical erosion rhythms of the West African Cenozoic morphogenesis: The 39Ar-40Ar dating of supergene K-Mn oxides

NASA Astrophysics Data System (ADS)

Beauvais, Anicet; Ruffet, Gilles; HéNocque, Olivier; Colin, Fabrice

2008-12-01

Chemical weathering and mechanical erosion are first-order processes of long-term tropical morphogenesis, which is still poorly deciphered for lack of time constraints. We address this issue by laser probe 39Ar-40Ar dating of generations of cryptomelane [K1-2Mn8O16, nH2O] from the manganese ore deposit of Tambao in northern Burkina Faso. This Mn deposit results from the supergene weathering of carbonate and silicate Mn protores underneath lateritic palaeolandsurfaces. It consists of an upper cryptomelane-rich domain and a lower domain where pyrolusite (β-MnO2) is the dominant Mn oxide. The oldest 39Ar-40Ar ages (59-45 Ma) are obtained on surface outcrops while the youngest ones characterize deep oxidation fronts (3.4-2.9 Ma). Apparent correlations of 39Ar-40Ar age groups with δ18O and eustatic curves allow definition of the different stages of morphogenesis. Paleocene-Eocene ages (59-45 Ma) bracket a greenhouse period propitious to bauxitic weathering. The lack of significant ages between ˜45 and 29 Ma characterizes a period dominated by mechanical erosion, during which detrital sediments, including lateritic materials, were accumulated in intracratonic basins allowing the exhumation of a new lateritic landsurface. Two major weathering periods separated by a second erosion episode (24-18 Ma) are also depicted at the end of Oligocene (29-24 Ma) and lower to mid-Miocene (18-11.5 Ma) in the upper domain, during which newly shaped land surfaces conspicuously weathered. The shorter-weathering and erosion episodes recorded in the lower domain from ˜18 to ˜2.9 Ma led to the final geomorphic changes that were conducive to the formation of glacis. The preservation of old cryptomelane (59-45 Ma) in the upper part of the ore deposit indicates a Cenozoic denudation limited to the erosion of previous bauxites, and partly, of ferricretes.

Contribution to the Study of Regional Magnetization of Satellite Magnetic Measurement: Magsat, Orsted, and Champ (with Gravity Field)

NASA Technical Reports Server (NTRS)

Taylor, Patrick T.

2004-01-01

A discussion of and introduction to satellite-altitude geopotential field studies and their interpretation with emphasis on results from metalliferous regions will be given. The magnetic and gravimetric measurements from satellite altitudes show heterogeneity in deeper parts of the lithosphere. These patterns of magnetic anomalies do not only reveal the largest iron ore deposits such as Kiruna, Sweden, Kursk, Russia, and Banugi, Central African Republic but also linear features indicating structural discontinuities. Changes of magnetic amplitude of these patterns are caused by intersecting transverse fractures localizing magmatism and concentration of metals. In addition satellite altitude data are related to variations in crustal thickness and heat flow. Deep-rooted structural discontinuities, defined by combination of geological and geophysical criteria, with spacing of several hundred kilometers, reveal a quite uniform pattern in the deeper parts of the lithosphere. As these structures provide favorable pathways for the ascent of heat, magmas and ore-forming fluids, their recognition is of crucial importance and can be used in the compilation of a new type of mineral prognosis map. An example from Europe includes a pattern of east west trending structural discontinuities or belts and their junction with the NW-trending Tornqvist-Teisseyre Line. The Upper Silesian-Cracovian Zn-Pb district occurs along one of the latitudinal belts. Leslaw Teper of the University of Silesia has been invited to show the fractures in crystalline basement beneath the sediments hosting the Zn-Pb ores.

A study of the trace sulfide mineral assemblages in the Stillwater Complex, Montana, USA

NASA Astrophysics Data System (ADS)

Aird, Hannah M.; Ferguson, Katherine M.; Lehrer, Malia L.; Boudreau, Alan E.

2017-03-01

The sulfide assemblages of the Stillwater Complex away from the well-studied ore zones are composed mainly of variable proportions of pyrrhotite, chalcopyrite, pentlandite, and ±pyrite. Excluding vein assemblages and those affected by greenschist and lower temperature alteration, the majority can be classified into two broad assemblages, defined here as pristine (multiphase, often globular in shape) or volatile-bearing (multiphase, high-temperature, volatile-rich minerals such as biotite, hornblende, or an unmixed calcite-dolomite assemblage). The volatile-bearing assemblages are mainly found within and below the J-M reef, where native copper and sphalerite are also locally present. Pristine sulfides are found throughout the stratigraphy. Both groups can be affected by apparent S loss in the form of pyrite being converted to magnetite and chalcopyrite to a Cu-Fe-oxide (delafossite), with little to no silicate alteration. An upward trend from pentlandite-rich to pyrrhotite-rich to pyrite-rich assemblages is observed in the footwall rocks in upper GN-I, and the same trend repeats from just below the reef and continues into the overlying N-II and GN-II. Modeling suggests that the sulfide Ni in the Peridotite Zone is largely controlled by silicate Ni. When taken together, observations are most readily explained by the remobilization of selected elements by a high-temperature fluid with the apparent loss of S > Cu > Ni. This could concentrate ore metals by vapor refining, eventually producing a platinum group element-enriched sulfide ore zone, such as the J-M reef.

Modeling of planar varactor frequency multiplier devices with blocking barriers

NASA Technical Reports Server (NTRS)

Lieneweg, Udo; Tolmunen, T. J.; Frerking, Margaret A.; Maserjian, Joseph

1992-01-01

Models for optimization of planar frequency triplers with symmetrical C-V curves are presented. Role and limitation of various blocking barriers (oxide, Mott, heterojunction) are discussed. Devices with undoped drift regions (BIN) have moderate efficiency but a broad range of power operation, whereas devices with doped drift regions (BNN) have high efficiency in a narrow power window. In particular, an upper power limit of the BNN is caused by electron velocity saturation. Implementations in SiO2/Si and AlAs/GaAs and means for increasing the power of BNN structures are considered.

Modeling of planar varactor frequency multiplier devices with blocking barriers

NASA Astrophysics Data System (ADS)

Lieneweg, Udo; Tolmunen, T. J.; Frerking, Margaret A.; Maserjian, Joseph

1992-05-01

Models for optimization of planar frequency triplers with symmetrical C-V curves are presented. Role and limitation of various blocking barriers (oxide, Mott, heterojunction) are discussed. Devices with undoped drift regions (BIN) have moderate efficiency but a broad range of power operation, whereas devices with doped drift regions (BNN) have high efficiency in a narrow power window. In particular, an upper power limit of the BNN is caused by electron velocity saturation. Implementations in SiO2/Si and AlAs/GaAs and means for increasing the power of BNN structures are considered.

Occupational exposure of aldehydes resulting from the storage of wood pellets.

PubMed

Rahman, Mohammad Arifur; Rossner, Alan; Hopke, Philip K

2017-06-01

An exposure assessment was conducted to investigate the potential for harmful concentrations of airborne short chain aldehydes emitted from recently stored wood pellets. Wood pellets can emit a number of airborne aldehydes include acetaldehyde, formaldehyde, propionaldehyde, butyraldehyde, valeraldehyde, and hexanal. Exposure limits have been set for these compounds since they can result in significant irritation of the upper respiratory system at elevated concentrations. Formaldehyde is a recognized human carcinogen and acetaldehyde is an animal carcinogen. Thus, air sampling was performed in a wood pellet warehouse at a pellet mill, two residential homes with bulk wood pellet storage bins, and in controlled laboratory experiments to evaluate the risk to occupants. Using NIOSH method 2539, sampling was conducted in five locations in the warehouse from April-June 2016 when it contained varying quantities of bagged pellets as well as two homes with ten ton bulk storage bins. The aldehyde concentrations were found to increase with the amount of stored pellets. Airborne concentrations of formaldehyde were as high as 0.45 ppm in the warehouse exceeding the NIOSH REL-C, and ACGIH TLV-C occupational exposure limits (OELs). The concentrations of aldehydes measured in the residential bins were also elevated indicating emissions may raise indoor air quality concerns for occupants. While individual exposures are of concern the combined irritant effect of all the aldehydes is a further raise the concerns for building occupants. To minimize exposure and the risk of adverse health effects to a building's occupants in storage areas with large quantities of pellets, adequate ventilation must be designed into storage areas.

Uranium content and leachable fraction of fluorspars

USGS Publications Warehouse

Landa, E.R.; Councell, T.B.

2000-01-01

Much attention in the radiological health community has recently focused on the management and regulation of naturally occurring radioactive materials. Although uranium-bearing minerals are present in a variety of fluorspar deposits, their potential consideration as naturally occurring radioactive materials has received only limited recognition. The uranium content of 28 samples of acid- and cryolite-grade (>97% CaF2) fluorspar from the National Defense Stockpile was found to range from 120 to 24,200 ??g kg-1, with a mean of 2,145 ??g kg-1. As a point of comparison, the average concentration of uranium in the upper crust of the earth is about 2,500 ??g kg-1. Leachability of this uranium was assessed by means of the Toxicity Characteristic Leaching Procedure (TCLP). The TCLP extractable fraction ranged from 1 to 98%, with a mean of 24% of the total uranium. The typically low concentrations of uranium seen in these materials probably reflects the removal of uranium-bearing mineral phases during the beneficiation of the crude fluorspar ore to achieve industrial specifications. Future NORM studies should examine crude fluorspar ores and flotation tailings.

Removal of phosphorus-rich phase from high-phosphorous iron ore by melt separation at 1573 K in a super-gravity field

NASA Astrophysics Data System (ADS)

Gao, Jin-tao; Guo, Lei; Zhong, Yi-wei; Ren, Hong-ru; Guo, Zhan-cheng

2016-07-01

A new approach of removing the phosphorus-rich phase from high-phosphorous iron ore by melt separation at 1573 K in a super- gravity field was investigated. The iron-slag separation by super-gravity resulted in phosphorus being effectively removed from the iron-rich phase and concentrated as a phosphorus-rich phase at a temperature below the melting point of iron. The samples obtained by super-gravity exhibited obvious layered structures. All the iron grains concentrated at the bottom of the sample along the super-gravity direction, whereas the molten slag concentrated in the upper part of the sample along the opposite direction. Meanwhile, fine apatite crystals collided and grew into larger crystals and concentrated at the slag-iron interface. Consequently, in the case of centrifugation with a gravity coefficient of G = 900, the mass fractions of the slag phase and iron-rich phase were similar to their respective theoretical values. The mass fraction of MFe in the iron-rich phase was as high as 97.77wt% and that of P was decreased to 0.092wt%.

Disrupted Membrane Structure and Intracellular Ca2+ Signaling in Adult Skeletal Muscle with Acute Knockdown of Bin1

PubMed Central

Tjondrokoesoemo, Andoria; Park, Ki Ho; Ferrante, Christopher; Komazaki, Shinji; Lesniak, Sebastian; Brotto, Marco; Ko, Jae-Kyun; Zhou, Jingsong; Weisleder, Noah; Ma, Jianjie

2011-01-01

Efficient intracellular Ca2+ ([Ca2+]i) homeostasis in skeletal muscle requires intact triad junctional complexes comprised of t-tubule invaginations of plasma membrane and terminal cisternae of sarcoplasmic reticulum. Bin1 consists of a specialized BAR domain that is associated with t-tubule development in skeletal muscle and involved in tethering the dihydropyridine receptors (DHPR) to the t-tubule. Here, we show that Bin1 is important for Ca2+ homeostasis in adult skeletal muscle. Since systemic ablation of Bin1 in mice results in postnatal lethality, in vivo electroporation mediated transfection method was used to deliver RFP-tagged plasmid that produced short –hairpin (sh)RNA targeting Bin1 (shRNA-Bin1) to study the effect of Bin1 knockdown in adult mouse FDB skeletal muscle. Upon confirming the reduction of endogenous Bin1 expression, we showed that shRNA-Bin1 muscle displayed swollen t-tubule structures, indicating that Bin1 is required for the maintenance of intact membrane structure in adult skeletal muscle. Reduced Bin1 expression led to disruption of t-tubule structure that was linked with alterations to intracellular Ca2+ release. Voltage-induced Ca2+ released in isolated single muscle fibers of shRNA-Bin1 showed that both the mean amplitude of Ca2+ current and SR Ca2+ transient were reduced when compared to the shRNA-control, indicating compromised coupling between DHPR and ryanodine receptor 1. The mean frequency of osmotic stress induced Ca2+ sparks was reduced in shRNA-Bin1, indicating compromised DHPR activation. ShRNA-Bin1 fibers also displayed reduced Ca2+ sparks' amplitude that was attributed to decreased total Ca2+ stores in the shRNA-Bin1 fibers. Human mutation of Bin1 is associated with centronuclear myopathy and SH3 domain of Bin1 is important for sarcomeric protein organization in skeletal muscle. Our study showing the importance of Bin1 in the maintenance of intact t-tubule structure and ([Ca2+]i) homeostasis in adult skeletal muscle could provide mechanistic insight on the potential role of Bin1 in skeletal muscle contractility and pathology of myopathy. PMID:21984944

VarBin, a novel method for classifying true and false positive variants in NGS data

PubMed Central

2013-01-01

Background Variant discovery for rare genetic diseases using Illumina genome or exome sequencing involves screening of up to millions of variants to find only the one or few causative variant(s). Sequencing or alignment errors create "false positive" variants, which are often retained in the variant screening process. Methods to remove false positive variants often retain many false positive variants. This report presents VarBin, a method to prioritize variants based on a false positive variant likelihood prediction. Methods VarBin uses the Genome Analysis Toolkit variant calling software to calculate the variant-to-wild type genotype likelihood ratio at each variant change and position divided by read depth. The resulting Phred-scaled, likelihood-ratio by depth (PLRD) was used to segregate variants into 4 Bins with Bin 1 variants most likely true and Bin 4 most likely false positive. PLRD values were calculated for a proband of interest and 41 additional Illumina HiSeq, exome and whole genome samples (proband's family or unrelated samples). At variant sites without apparent sequencing or alignment error, wild type/non-variant calls cluster near -3 PLRD and variant calls typically cluster above 10 PLRD. Sites with systematic variant calling problems (evident by variant quality scores and biases as well as displayed on the iGV viewer) tend to have higher and more variable wild type/non-variant PLRD values. Depending on the separation of a proband's variant PLRD value from the cluster of wild type/non-variant PLRD values for background samples at the same variant change and position, the VarBin method's classification is assigned to each proband variant (Bin 1 to Bin 4). Results To assess VarBin performance, Sanger sequencing was performed on 98 variants in the proband and background samples. True variants were confirmed in 97% of Bin 1 variants, 30% of Bin 2, and 0% of Bin 3/Bin 4. Conclusions These data indicate that VarBin correctly classifies the majority of true variants as Bin 1 and Bin 3/4 contained only false positive variants. The "uncertain" Bin 2 contained both true and false positive variants. Future work will further differentiate the variants in Bin 2. PMID:24266885

SPHINX--an algorithm for taxonomic binning of metagenomic sequences.

PubMed

Mohammed, Monzoorul Haque; Ghosh, Tarini Shankar; Singh, Nitin Kumar; Mande, Sharmila S

2011-01-01

Compared with composition-based binning algorithms, the binning accuracy and specificity of alignment-based binning algorithms is significantly higher. However, being alignment-based, the latter class of algorithms require enormous amount of time and computing resources for binning huge metagenomic datasets. The motivation was to develop a binning approach that can analyze metagenomic datasets as rapidly as composition-based approaches, but nevertheless has the accuracy and specificity of alignment-based algorithms. This article describes a hybrid binning approach (SPHINX) that achieves high binning efficiency by utilizing the principles of both 'composition'- and 'alignment'-based binning algorithms. Validation results with simulated sequence datasets indicate that SPHINX is able to analyze metagenomic sequences as rapidly as composition-based algorithms. Furthermore, the binning efficiency (in terms of accuracy and specificity of assignments) of SPHINX is observed to be comparable with results obtained using alignment-based algorithms. A web server for the SPHINX algorithm is available at http://metagenomics.atc.tcs.com/SPHINX/.

MaxBin 2.0: an automated binning algorithm to recover genomes from multiple metagenomic datasets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Yu-Wei; Simmons, Blake A.; Singer, Steven W.

The recovery of genomes from metagenomic datasets is a critical step to defining the functional roles of the underlying uncultivated populations. We previously developed MaxBin, an automated binning approach for high-throughput recovery of microbial genomes from metagenomes. Here, we present an expanded binning algorithm, MaxBin 2.0, which recovers genomes from co-assembly of a collection of metagenomic datasets. Tests on simulated datasets revealed that MaxBin 2.0 is highly accurate in recovering individual genomes, and the application of MaxBin 2.0 to several metagenomes from environmental samples demonstrated that it could achieve two complementary goals: recovering more bacterial genomes compared to binning amore » single sample as well as comparing the microbial community composition between different sampling environments. Availability and implementation: MaxBin 2.0 is freely available at http://sourceforge.net/projects/maxbin/ under BSD license. Supplementary information: Supplementary data are available at Bioinformatics online.« less

A Nonlinearity Minimization-Oriented Resource-Saving Time-to-Digital Converter Implemented in a 28 nm Xilinx FPGA

NASA Astrophysics Data System (ADS)

Wang, Yonggang; Liu, Chong

2015-10-01

Because large nonlinearity errors exist in the current tapped-delay line (TDL) style field programmable gate array (FPGA)-based time-to-digital converters (TDC), bin-by-bin calibration techniques have to be resorted for gaining a high measurement resolution. If the TDL in selected FPGAs is significantly affected by changes in ambient temperature, the bin-by-bin calibration table has to be updated as frequently as possible. The on-line calibration and calibration table updating increase the TDC design complexity and limit the system performance to some extent. This paper proposes a method to minimize the nonlinearity errors of TDC bins, so that the bin-by-bin calibration may not be needed while maintaining a reasonably high time resolution. The method is a two pass approach: By a bin realignment, the large number of wasted zero-width bins in the original TDL is reused and the granularity of the bins is improved; by a bin decimation, the bin size and its uniformity is traded-off, and the time interpolation by the delay line turns more precise so that the bin-by-bin calibration is not necessary. Using Xilinx 28 nm FPGAs, in which the TDL property is not very sensitive to ambient temperature, the proposed TDC achieves approximately 15 ps root-mean-square (RMS) time resolution by dual-channel measurements of time-intervals over the range of operating temperature. Because of removing the calibration and less logic resources required for the data post-processing, the method has bigger multi-channel capability.

On the origin of the Neoproterozoic Peresopolis graphite deposit, Paraguay Belt, Brazil

NASA Astrophysics Data System (ADS)

Manoel, Talitta Nunes; Dexheimer Leite, Jayme Alfredo

2018-07-01

The Peresopolis graphite deposit is located northeast of Brasilândia Town in Mato Grosso State (Brazil). It consists of an 1800 m long, 200 m wide low-crystallinity graphite-bearing tabular layer that trends ENE and dips 65°ESE. The deposit is hosted in carbonaceous phyllites, which along with basal metadiamictites and upper metarenites make up the upper unit (Coxipó Formation) of the Cuiabá Group in the late Cryogenian to Cambrian Paraguay Belt (ca. 650-500Ma). The carbonaceous phyllites show a mineral assemblage consisting mostly of graphite-quartz-muscovite-albite and pyrite and dolomite to a lesser extent; alteration minerals include tosudite and kaolinite. XRD analysis confirmed the gangue material and defined the graphite as low-order crystallinity. Carbon isotope data for graphite ore returned a light and very restricted range of δ13Corg between -29 and -28‰ suggesting organic matter as the source of carbon. One hundred and sixty measurements of Raman graphite spectrum returned a well-fit between full width at half maximum parameter (FWHM) which allowed its use as a geothermometer. Resulting temperatures are in the range between 285 and 300 °C ± 30 °C, indicating low-to very-low metamorphic conditions for transformation of organic matter into amorphous graphite. The deposition of the organic matter should have taken place in an outer slope of a glaciomarine system and its transformation into the ore occurred because of deformation and low-grade metamorphism related to the development of the Neoproterozoic Brasiliano/Pan-African Orogeny (850-500Ma).

Modulation of magmatic processes by CO2 flushing

NASA Astrophysics Data System (ADS)

Caricchi, Luca; Sheldrake, Tom E.; Blundy, Jon

2018-06-01

Magmatic systems are the engines driving volcanic eruptions and the source of fluids responsible for the formation of porphyry-type ore deposits. Sudden variations of pressure, temperature and volume in magmatic systems can produce unrest, which may culminate in a volcanic eruption and/or the abrupt release of ore-forming fluids. Such variations of the conditions within magmatic systems are commonly ascribed to the injection of new magma from depth. However, as magmas fractionating at depth or rising to the upper crust release CO2-rich fluids, the interaction between carbonic fluids and H2O-rich magmas stored in the upper crust (CO2 flushing), must also be a common process affecting the evolution of subvolcanic magma reservoirs. Here, we investigate the effect of gas injection on the stability and chemical evolution of magmatic systems. We calculate the chemical and physical evolution of magmas subjected to CO2-flushing using rhyolite-MELTS. We compare the calculations with a set of melt inclusion data for Mt. St. Helens, Merapi, Etna, and Stromboli volcanoes. We provide an approach that can be used to distinguish between melt inclusions trapped during CO2 flushing, magma ascent and decompression, or those affected by post-entrapment H2O-loss. Our results show that CO2 flushing is a widespread process in both felsic and mafic magmatic systems. Depending upon initial magma crystallinity and duration of CO2 input, flushing can either lead to volcanic eruption or fluid release. We suggest that CO2 flushing is a fundamental process modulating the behaviour and chemical evolution of crustal magmatic systems.

Brassinosteroids regulate pavement cell growth by mediating BIN2-induced microtubule stabilization.

PubMed

Liu, Xiaolei; Yang, Qin; Wang, Yuan; Wang, Linhai; Fu, Ying; Wang, Xuelu

2018-02-23

Brassinosteroids (BRs), a group of plant steroid hormones, play important roles in regulating plant development. The cytoskeleton also affects key developmental processes and a deficiency in BR biosynthesis or signaling leads to abnormal phenotypes similar to those of microtubule-defective mutants. However, how BRs regulate microtubule and cell morphology remains unknown. Here, using liquid chromatography-tandem mass spectrometry, we identified tubulin proteins that interact with Arabidopsis BRASSINOSTEROID INSENSITIVE2 (BIN2), a negative regulator of BR responses in plants. In vitro and in vivo pull-down assays confirmed that BIN2 interacts with tubulin proteins. High-speed co-sedimentation assays demonstrated that BIN2 also binds microtubules. The Arabidopsis genome also encodes two BIN2 homologs, BIN2-LIKE 1 (BIL1) and BIL2, which function redundantly with BIN2. In the bin2-3 bil1 bil2 triple mutant, cortical microtubules were more sensitive to treatment with the microtubule-disrupting drug oryzalin than in wild-type, whereas in the BIN2 gain-of-function mutant bin2-1, cortical microtubules were insensitive to oryzalin treatment. These results provide important insight into how BR regulates plant pavement cell and leaf growth by mediating the stabilization of microtubules by BIN2.

The ESCRT-III pathway facilitates cardiomyocyte release of cBIN1-containing microparticles

PubMed Central

Xu, Bing; Fu, Ying; Liu, Yan; Agvanian, Sosse; Wirka, Robert C.; Baum, Rachel; Zhou, Kang; Shaw, Robin M.

2017-01-01

Microparticles (MPs) are cell–cell communication vesicles derived from the cell surface plasma membrane, although they are not known to originate from cardiac ventricular muscle. In ventricular cardiomyocytes, the membrane deformation protein cardiac bridging integrator 1 (cBIN1 or BIN1+13+17) creates transverse-tubule (t-tubule) membrane microfolds, which facilitate ion channel trafficking and modulate local ionic concentrations. The microfold-generated microdomains continuously reorganize, adapting in response to stress to modulate the calcium signaling apparatus. We explored the possibility that cBIN1-microfolds are externally released from cardiomyocytes. Using electron microscopy imaging with immunogold labeling, we found in mouse plasma that cBIN1 exists in membrane vesicles about 200 nm in size, which is consistent with the size of MPs. In mice with cardiac-specific heterozygous Bin1 deletion, flow cytometry identified 47% less cBIN1-MPs in plasma, supporting cardiac origin. Cardiac release was also evidenced by the detection of cBIN1-MPs in medium bathing a pure population of isolated adult mouse cardiomyocytes. In human plasma, osmotic shock increased cBIN1 detection by enzyme-linked immunosorbent assay (ELISA), and cBIN1 level decreased in humans with heart failure, a condition with reduced cardiac muscle cBIN1, both of which support cBIN1 release in MPs from human hearts. Exploring putative mechanisms of MP release, we found that the membrane fission complex endosomal sorting complexes required for transport (ESCRT)-III subunit charged multivesicular body protein 4B (CHMP4B) colocalizes and coimmunoprecipitates with cBIN1, an interaction enhanced by actin stabilization. In HeLa cells with cBIN1 overexpression, knockdown of CHMP4B reduced the release of cBIN1-MPs. Using truncation mutants, we identified that the N-terminal BAR (N-BAR) domain in cBIN1 is required for CHMP4B binding and MP release. This study links the BAR protein superfamily to the ESCRT pathway for MP biogenesis in mammalian cardiac ventricular cells, identifying elements of a pathway by which cytoplasmic cBIN1 is released into blood. PMID:28806752

The ESCRT-III pathway facilitates cardiomyocyte release of cBIN1-containing microparticles.

PubMed

Xu, Bing; Fu, Ying; Liu, Yan; Agvanian, Sosse; Wirka, Robert C; Baum, Rachel; Zhou, Kang; Shaw, Robin M; Hong, TingTing

2017-08-01

Microparticles (MPs) are cell-cell communication vesicles derived from the cell surface plasma membrane, although they are not known to originate from cardiac ventricular muscle. In ventricular cardiomyocytes, the membrane deformation protein cardiac bridging integrator 1 (cBIN1 or BIN1+13+17) creates transverse-tubule (t-tubule) membrane microfolds, which facilitate ion channel trafficking and modulate local ionic concentrations. The microfold-generated microdomains continuously reorganize, adapting in response to stress to modulate the calcium signaling apparatus. We explored the possibility that cBIN1-microfolds are externally released from cardiomyocytes. Using electron microscopy imaging with immunogold labeling, we found in mouse plasma that cBIN1 exists in membrane vesicles about 200 nm in size, which is consistent with the size of MPs. In mice with cardiac-specific heterozygous Bin1 deletion, flow cytometry identified 47% less cBIN1-MPs in plasma, supporting cardiac origin. Cardiac release was also evidenced by the detection of cBIN1-MPs in medium bathing a pure population of isolated adult mouse cardiomyocytes. In human plasma, osmotic shock increased cBIN1 detection by enzyme-linked immunosorbent assay (ELISA), and cBIN1 level decreased in humans with heart failure, a condition with reduced cardiac muscle cBIN1, both of which support cBIN1 release in MPs from human hearts. Exploring putative mechanisms of MP release, we found that the membrane fission complex endosomal sorting complexes required for transport (ESCRT)-III subunit charged multivesicular body protein 4B (CHMP4B) colocalizes and coimmunoprecipitates with cBIN1, an interaction enhanced by actin stabilization. In HeLa cells with cBIN1 overexpression, knockdown of CHMP4B reduced the release of cBIN1-MPs. Using truncation mutants, we identified that the N-terminal BAR (N-BAR) domain in cBIN1 is required for CHMP4B binding and MP release. This study links the BAR protein superfamily to the ESCRT pathway for MP biogenesis in mammalian cardiac ventricular cells, identifying elements of a pathway by which cytoplasmic cBIN1 is released into blood.

Optimizing 4DCBCT projection allocation to respiratory bins.

PubMed

O'Brien, Ricky T; Kipritidis, John; Shieh, Chun-Chien; Keall, Paul J

2014-10-07

4D cone beam computed tomography (4DCBCT) is an emerging image guidance strategy used in radiotherapy where projections acquired during a scan are sorted into respiratory bins based on the respiratory phase or displacement. 4DCBCT reduces the motion blur caused by respiratory motion but increases streaking artefacts due to projection under-sampling as a result of the irregular nature of patient breathing and the binning algorithms used. For displacement binning the streak artefacts are so severe that displacement binning is rarely used clinically. The purpose of this study is to investigate if sharing projections between respiratory bins and adjusting the location of respiratory bins in an optimal manner can reduce or eliminate streak artefacts in 4DCBCT images. We introduce a mathematical optimization framework and a heuristic solution method, which we will call the optimized projection allocation algorithm, to determine where to position the respiratory bins and which projections to source from neighbouring respiratory bins. Five 4DCBCT datasets from three patients were used to reconstruct 4DCBCT images. Projections were sorted into respiratory bins using equispaced, equal density and optimized projection allocation. The standard deviation of the angular separation between projections was used to assess streaking and the consistency of the segmented volume of a fiducial gold marker was used to assess motion blur. The standard deviation of the angular separation between projections using displacement binning and optimized projection allocation was 30%-50% smaller than conventional phase based binning and 59%-76% smaller than conventional displacement binning indicating more uniformly spaced projections and fewer streaking artefacts. The standard deviation in the marker volume was 20%-90% smaller when using optimized projection allocation than using conventional phase based binning suggesting more uniform marker segmentation and less motion blur. Images reconstructed using displacement binning and the optimized projection allocation algorithm were clearer, contained visibly fewer streak artefacts and produced more consistent marker segmentation than those reconstructed with either equispaced or equal-density binning. The optimized projection allocation algorithm significantly improves image quality in 4DCBCT images and provides, for the first time, a method to consistently generate high quality displacement binned 4DCBCT images in clinical applications.

Geochemistry of the Johnson River, Lake Clark National Park and Preserve, Alaska

USGS Publications Warehouse

Brabets, Timothy P.; Riehle, James R.

2003-01-01

The Johnson River Basin, located in Lake Clark National Park and Preserve, drains an area of 96 square miles. A private inholding in the upper part of the basin contains a gold deposit that may be developed in the future. To establish a natural baseline to compare potential effects on water quality if development were to occur, the upper part of the Johnson River Basin was studied from 1999 to 2001 as part of a cooperative study with the National Park Service. Two basic rock types occur within the drainage basin of the study: the Jurassic Talkeetna Formation of interbedded volcanic and volcaniclastic rocks, and the slightly younger plutonic rocks of the Aleutian-Alaska Ranges batholith. The Johnson River gold prospect reflects widespread, secondary mineralization and alteration of the Talkeetna Formation. Metals found at the prospect proper are: arsenic, cadmium, copper, gold, iron, lead, mercury, molybdenum, selenium, silver, and zinc. The Johnson River prospect is located in the East Fork Ore Creek Basin, a 0.5 square mile watershed that is a tributary to the Johnson River. Water quality data from this stream reflect the mineralization of the basin and the highest concentrations of several trace elements and major ions of the water column were found in this stream. Presently, pH in this stream is normal, indicating that there is sufficient buffering capacity. At the Johnson River streamgage, which drains approximately 25 mi2 including the East Fork Ore Creek, concentrations of these constituents are significantly lower, reflecting the runoff from Johnson Glacier and Double Glacier, which account for approximately 75 percent of the total discharge. Streambed concentrations of cadmium, lead, and zinc from East Fork Ore Creek and its receiving stream, Ore Creek, typically exceed concentrations where sediment dwelling organisms would be affected. Similar to the water column chemistry, concentrations of these elements are lower at the Johnson River streamgage, reflecting the fine sediment input from the glacier streams draining Johnson Glacier and Double Glacier. The amount of organic carbon present in the study area is relatively low and most sites indicate that some degree of toxicity is present even though these basins do not contain mineralized areas. Acid based accounting tests on rock samples in the study area indicate a neutralizing capacity in the Talkeetna Formation rocks. These results should be used with caution because similar tests were not done on rocks from narrow veins or faults that could have acid generating potential. In addition, based on field tests during the study, carbonate-bearing rocks in streambeds are armored by a carbonate-depleted shell and would not readily neutralize acidic water.

Novel features and enhancements in BioBin, a tool for the biologically inspired binning and association analysis of rare variants

PubMed Central

Byrska-Bishop, Marta; Wallace, John; Frase, Alexander T; Ritchie, Marylyn D

2018-01-01

Abstract Motivation BioBin is an automated bioinformatics tool for the multi-level biological binning of sequence variants. Herein, we present a significant update to BioBin which expands the software to facilitate a comprehensive rare variant analysis and incorporates novel features and analysis enhancements. Results In BioBin 2.3, we extend our software tool by implementing statistical association testing, updating the binning algorithm, as well as incorporating novel analysis features providing for a robust, highly customizable, and unified rare variant analysis tool. Availability and implementation The BioBin software package is open source and freely available to users at http://www.ritchielab.com/software/biobin-download Contact mdritchie@geisinger.edu Supplementary information Supplementary data are available at Bioinformatics online. PMID:28968757

Characterisation and Processing of Some Iron Ores of India

NASA Astrophysics Data System (ADS)

Krishna, S. J. G.; Patil, M. R.; Rudrappa, C.; Kumar, S. P.; Ravi, B. P.

2013-10-01

Lack of process characterization data of the ores based on the granulometry, texture, mineralogy, physical, chemical, properties, merits and limitations of process, market and local conditions may mislead the mineral processing entrepreneur. The proper implementation of process characterization and geotechnical map data will result in optimized sustainable utilization of resource by processing. A few case studies of process characterization of some Indian iron ores are dealt with. The tentative ascending order of process refractoriness of iron ores is massive hematite/magnetite < marine black iron oxide sands < laminated soft friable siliceous ore fines < massive banded magnetite quartzite < laminated soft friable clayey aluminous ore fines < massive banded hematite quartzite/jasper < massive clayey hydrated iron oxide ore < manganese bearing iron ores massive < Ti-V bearing magnetite magmatic ore < ferruginous cherty quartzite. Based on diagnostic process characterization, the ores have been classified and generic process have been adopted for some Indian iron ores.

Porphyry copper deposits distribution along the western Tethyan and Andean subductions: insights from a paleogeographic approach

NASA Astrophysics Data System (ADS)

Bertrand, G.

2012-12-01

The genesis of many types of mineral deposits is closely linked to tectonic and petrographic conditions resulting from specific geodynamic contexts. Porphyry deposits, for instance, are associated to calc-alkaline magmatism of subduction zones. In order to better understand the relationships between ore deposit distribution and their tectonic context, and help identifying geodynamic-related criteria of favorability that would, in turn, help mineral exploration, we propose a paleogeographic approach. Paleogeographic reconstructions, based on global or regional plate tectonic models, are crucial tools to assess tectonic and kinematic contexts of the past. We use this approach to study the distribution of porphyry copper deposits along the western Tethyan and Andean subductions since Lower Cretaceous and Paleocene, respectively. For both convergent contexts, databases of porphyry copper deposits, including, among other data, their age and location, were compiled. Spatial and temporal distribution of the deposits is not random and show that they were emplaced in distinct clusters. Five clusters are identified along the western Tethyan suture, from Lower Cretaceous to Pleistocene, and at least three along the Andes, from Paleocene to Miocene. Two clusters in the Aegean-Balkan-Carpathian area, that were emplaced in Upper Cretaceous and Oligo-Miocene, and two others in the Andes, that were emplaced in late Eocene and Miocene, are studied in details and correlated with the past kinematics of the Africa-Eurasia and Nazca-South America plate convergences, respectively. All these clusters are associated with a similar polyphased kinematic context that is closely related to the dynamics of the subductions. This context is characterized by 1) a relatively fast convergence rate, shortly followed by 2) a drastic decrease of this rate. To explain these results, we propose a polyphased genetic model for porphyry copper deposits with 1) a first stage of rapid subduction rate, favoring high melt production in the mantle wedge, by dehydration of the subducted oceanic crust, and increased influx of mafic magmas in the MASH (Melting, Assimilation, Storage, Homogenization) zone, and 2) a subsequent significant decrease in subduction rate, favoring extensional regime within the upper plate and easing upward migration of fertile magmas to the upper crust. This second effect seems to be confirmed in the Aegean-Balkan-Carpathian area where the two clusters are spatially and temporally correlated with known extensional regimes. Although preliminary, these results highlight the control of the geodynamic context, and especially the subduction kinematics, on the spatial and temporal distribution of porphyry copper deposits. This study also confirms that the paleogeographic approach is a promising tool that could help identifying geodynamic and tectonic criteria favoring the genesis of various ore deposit types. Correlatively, ore deposits may be considered, in future studies, as possible markers of past geodynamic contexts.

Shuttle car loading system

NASA Technical Reports Server (NTRS)

Collins, E. R., Jr. (Inventor)

1985-01-01

A system is described for loading newly mined material such as coal, into a shuttle car, at a location near the mine face where there is only a limited height available for a loading system. The system includes a storage bin having several telescoping bin sections and a shuttle car having a bottom wall that can move under the bin. With the bin in an extended position and filled with coal the bin sections can be telescoped to allow the coal to drop out of the bin sections and into the shuttle car, to quickly load the car. The bin sections can then be extended, so they can be slowly filled with more while waiting another shuttle car.

Geology of the Shinarump No. 1 uranium mine, Seven Mile Canyon area, Grand County, Utah

USGS Publications Warehouse

Finch, Warren Irvin

1953-01-01

The Shinarump No. 1 uranium mine is located about 12 miles northwest of Moab, Utah, in the Seven Mile Canyon area, Grand County, Utah. A study was made of the geology of the Shinarump No. 1 mine in order to determine the habits, ore controls, and possible origin of the deposit. Rocks of Permain, Triassic, and Jurassic age crop out in the area mapped. Uranium deposits are found in three zones in the lower 25 feet of the Upper Triassic Chinle formation. The Shinarump No. 1 mine, which is in the lowermost zone, is located on the west flank of the Moab anticline near the Moab fault. The Shinarump No. 1 uranium deposit consists of discontinuous lenticular layers of mineralized rock, irregular in outline, that, in general, follow the bedding. Ore minerals, mainly uranite, impregnate the rock. High-grade seams of uranite and chalcocite occur along bedding planes. Formation of unraninite is later than or simultaneous with most sulfides. Chalcocite may be of two ages, with some being later than uraninite. Uraninite and chalcocite are concentrated in the poorer sorted parts of siltstones. Guides to ore in the Seven Mile Canyon area inferred from the study of the Shinarump No. 1 deposit are the presence of bleached siltstone, copper sulfides, and carbonaceous matter. Results of spectrographic analysis indicated that the mineralizing solutions contained important amounts of barium, vanadium, uranium, and copper as well as lesser amounts of strontium, chromium, boron, yttrium, lead, and zinc. The origin of the Shinarump No. 1 deposit is thought to be hydrothermal, dated as later or early.

Deep Structure of the Earth and Concentration of Metals in the Lithosphere: A Geodynamic Approach

NASA Technical Reports Server (NTRS)

Taylor, Patrick T.; Kutina, J.; Pei, R.

2004-01-01

A discussion of and introduction to satellite-altitude geopotential fields studies and their interpretation with emphasis on results from metalliferous regions will be given. The magnetic and gravimetric measurements from satellite altitudes show heterogeneity in deeper parts of the lithosphere. These patterns of magnetic anomalies do not only reveal the largest iron ore deposits such as Kiruna, Sweden and Kursk, Russia, but also linear features indicating structural discontinuities. Changes of magnetic amplitude of these patterns are caused by intersecting transverse fractures localizing magmatism and concentration of metals. The role of trans-regional mantle-rooted structural discontinuities in the concentration of metals will be discussed and a new type of mineral prognosis map will be presented. Deep-rooted structural discontinuities, defined by combination of geological and geophysical criteria, with spacing of several hundred kilometers, reveal a quite uniform pattern in the deeper parts of the lithosphere. As these structures provide favorable pathways for the ascent of heat, magmas and ore-forming fluids, their recognition is of crucial importance and can be used in the compilation of a new type of mineral prognosis map. Examples are shown from the United States, Canada, China, Burma, South America, Europe and Australia. The European example includes a pattern of east west trending structural discontinuities or belts and their junction with the NW-trending Tornqvist-Teisseyre Line. The Upper Silesian-Cracovian Zn-Pb district occurs along one of the latitudinal belts. Leslaw Teper of the University of Silesia has been invited to show the fractures in crystalline basement beneath the sediments hosting the Zn-Pb ores.

China's emergence as the world's leading iron-ore-consuming country

USGS Publications Warehouse

Kirk, W.S.

2004-01-01

China has become the leading iron ore consuming nation, and, based on recent steel production capacity increases and plans for more, its consumption will almost certainly to continue to grow. China's iron ore industry, however, faces a number of problems. China's iron ore is low-grade, expensive to process, and its mines are being depleted. For many Chinese steelmakers, particularly in the coastal regions, the delivered cost of domestic iron ore, is more than the delivered cost of foreign ore. Thus China's iron ore imports are expected to increase. As China's growth continues, it will almost certainly surpass Japan to become the leading iron ore importing country as well. Without China's increasing appetite for iron ore, the world iron ore market would be flat or declining. China's recent imports largely offset the slump in demand in North America and Europe. China is regarded by the iron ore industry as the growth sector for the next decade. Although Chinese imports are expected to continue their rapid increase and imports in other Asian countries are expected to continue growing, there appears to be enough greenfield and expansion projects to meet future demand for iron ore worldwide. Present suppliers of iron ore, Australia, Brazil, India, and South Africa, will probably be the chief beneficiaries of China's increasing consumption of iron ore. How long China can continue its extraordinary growth is the primary issue for the future of the iron ore industry. Based on the number and size of planned blast furnaces it appears that China's growth could continue for several more years. ?? 2004 Taylor and Francis.

Nitrile O-ring Cracking: A Case of Vacuum Flange O-ring Failures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dees, Craig

2016-07-01

A review of recent nitrile O-ring failures in ISO-KF vacuum flange connections in glovebox applications is presented. An investigation of a single “isolated” o-ring failure leads to the discovery of cracked nitrile o-rings in a glovebox atmospheric control unit. The initial cause of the o-ring failure is attributed to ozone degradation. However, additional investigation reveals nitrile o-ring cracking on multiple gloveboxes and general purpose piping, roughly 85% of the nitrile o-rings removed for inspection show evidence of visible cracking after being in service for 18 months or less. The results of material testing and ambient air testing is presented, elevatedmore » ozone levels are not found. The contributing factors of o-ring failure, including nitrile air sensitivity, inadequate storage practices, and poor installation techniques, are discussed. A discussion of nitrile o-ring material properties, the benefits and limitations, and alternate materials are discussed. Considerations for o-ring material selection, purchasing, storage, and installation are presented in the context of lessons learned from the nitrile o-ring cracking investigation. This paper can be presented in 20 minutes and does not require special accommodations or special audio visual devices.« less

Effect of various binning methods and ROI sizes on the accuracy of the automatic classification system for differentiation between diffuse infiltrative lung diseases on the basis of texture features at HRCT

NASA Astrophysics Data System (ADS)

Kim, Namkug; Seo, Joon Beom; Sung, Yu Sub; Park, Bum-Woo; Lee, Youngjoo; Park, Seong Hoon; Lee, Young Kyung; Kang, Suk-Ho

2008-03-01

To find optimal binning, variable binning size linear binning (LB) and non-linear binning (NLB) methods were tested. In case of small binning size (Q <= 10), NLB shows significant better accuracy than the LB. K-means NLB (Q = 26) is statistically significant better than every LB. To find optimal binning method and ROI size of the automatic classification system for differentiation between diffuse infiltrative lung diseases on the basis of textural analysis at HRCT Six-hundred circular regions of interest (ROI) with 10, 20, and 30 pixel diameter, comprising of each 100 ROIs representing six regional disease patterns (normal, NL; ground-glass opacity, GGO; reticular opacity, RO; honeycombing, HC; emphysema, EMPH; and consolidation, CONS) were marked by an experienced radiologist from HRCT images. Histogram (mean) and co-occurrence matrix (mean and SD of angular second moment, contrast, correlation, entropy, and inverse difference momentum) features were employed to test binning and ROI effects. To find optimal binning, variable binning size LB (bin size Q: 4~30, 32, 64, 128, 144, 196, 256, 384) and NLB (Q: 4~30) methods (K-means, and Fuzzy C-means clustering) were tested. For automated classification, a SVM classifier was implemented. To assess cross-validation of the system, a five-folding method was used. Each test was repeatedly performed twenty times. Overall accuracies with every combination of variable ROIs, and binning sizes were statistically compared. In case of small binning size (Q <= 10), NLB shows significant better accuracy than the LB. K-means NLB (Q = 26) is statistically significant better than every LB. In case of 30x30 ROI size and most of binning size, the K-means method showed better than other NLB and LB methods. When optimal binning and other parameters were set, overall sensitivity of the classifier was 92.85%. The sensitivity and specificity of the system for each class were as follows: NL, 95%, 97.9%; GGO, 80%, 98.9%; RO 85%, 96.9%; HC, 94.7%, 97%; EMPH, 100%, 100%; and CONS, 100%, 100%, respectively. We determined the optimal binning method and ROI size of the automatic classification system for differentiation between diffuse infiltrative lung diseases on the basis of texture features at HRCT.

CoMet: a workflow using contig coverage and composition for binning a metagenomic sample with high precision.

PubMed

Herath, Damayanthi; Tang, Sen-Lin; Tandon, Kshitij; Ackland, David; Halgamuge, Saman Kumara

2017-12-28

In metagenomics, the separation of nucleotide sequences belonging to an individual or closely matched populations is termed binning. Binning helps the evaluation of underlying microbial population structure as well as the recovery of individual genomes from a sample of uncultivable microbial organisms. Both supervised and unsupervised learning methods have been employed in binning; however, characterizing a metagenomic sample containing multiple strains remains a significant challenge. In this study, we designed and implemented a new workflow, Coverage and composition based binning of Metagenomes (CoMet), for binning contigs in a single metagenomic sample. CoMet utilizes coverage values and the compositional features of metagenomic contigs. The binning strategy in CoMet includes the initial grouping of contigs in guanine-cytosine (GC) content-coverage space and refinement of bins in tetranucleotide frequencies space in a purely unsupervised manner. With CoMet, the clustering algorithm DBSCAN is employed for binning contigs. The performances of CoMet were compared against four existing approaches for binning a single metagenomic sample, including MaxBin, Metawatt, MyCC (default) and MyCC (coverage) using multiple datasets including a sample comprised of multiple strains. Binning methods based on both compositional features and coverages of contigs had higher performances than the method which is based only on compositional features of contigs. CoMet yielded higher or comparable precision in comparison to the existing binning methods on benchmark datasets of varying complexities. MyCC (coverage) had the highest ranking score in F1-score. However, the performances of CoMet were higher than MyCC (coverage) on the dataset containing multiple strains. Furthermore, CoMet recovered contigs of more species and was 18 - 39% higher in precision than the compared existing methods in discriminating species from the sample of multiple strains. CoMet resulted in higher precision than MyCC (default) and MyCC (coverage) on a real metagenome. The approach proposed with CoMet for binning contigs, improves the precision of binning while characterizing more species in a single metagenomic sample and in a sample containing multiple strains. The F1-scores obtained from different binning strategies vary with different datasets; however, CoMet yields the highest F1-score with a sample comprised of multiple strains.

Composite correlation filter for O-ring detection in stationary colored noise

NASA Astrophysics Data System (ADS)

Hassebrook, Laurence G.

2009-04-01

O-rings are regularly replaced in aircraft and if they are not replaced or if they are installed improperly, they can result in catastrophic failure of the aircraft. It is critical that the o-rings be packaged correctly to avoid mistakes made by technicians during routine maintenance. For this reason, fines may be imposed on the o-ring manufacturer if the o-rings are packaged incorrectly. That is, a single o-ring must be packaged and labeled properly. No o-rings or more than one o-ring per package is not acceptable. We present an industrial inspection system based on real-time composite correlation filtering that has successfully solved this problem in spite of opaque paper o-ring packages. We present the system design including the composite filter design.

Ore-fluid evolution at the Getchell Carlin-type gold deposit, Nevada, USA

USGS Publications Warehouse

Cline, J.S.; Hofstra, A.A.

2000-01-01

Minerals and fluid-inclusion populations were examined using petrography, microthermometry, quadrupole mass-spectrometer gas analyses and stable-isotope studies to characterize fluids responsible for gold mineralization at the Getchell Carlin-type gold deposit. The gold-ore assemblage at Getchell is superimposed on quartz-pyrite vein mineralization associated with a Late-Cretaceous granodiorite stock that intruded Lower-Paleozoic sedimentary rocks. The ore assemblage, of mid-Tertiary age, consists of disseminated arsenian pyrite that contains submicrometer gold, jasperoid quartz, and later fluorite and orpiment that fill fractures and vugs. Late ore-stage realgar and calcite enclose ore-stage minerals. Pre-ore quartz trapped fluids with a wide range of salinities (1 to 21 wt.% NaCl equivalent), gas compositions (H2O, CO2, and CH4), and temperatures (120 to >360??C). Oxygen- and hydrogen-isotope ratios indicate that pre-ore fluids likely had a magmatic source, and were associated with intrusion of the granodiorite stock and related dikes. Ore-stage jasperoid contains moderate salinity, aqueous fluid inclusions trapped at 180 to 220??C. Ore fluids contain minor CO2 and trace H2S that allowed the fluid to react with limestone host rocks and transport gold, respectively. Aqueous inclusions in fluorite indicate that fluid temperatures declined to ~175??C by the end of ore-stage mineralization. As the hydrothermal system collapsed, fluid temperatures declined to 155 to 115??C and realgar and calcite precipitated. Inclusion fluids in ore-stage minerals have high ??D(H2O) and ??18O(H2O) values that indicate that the fluid had a deep source, and had a metamorphic or magmatic origin, or both. Late ore-stage fluids extend to lower ??D(H2O) values, and have a wider range of ??18O(H2O) values suggesting dilution by variably exchanged meteoric waters. Results show that deeply sourced ore fluids rose along the Getchell fault system, where they dissolved carbonate wall rocks and deposited gold-enriched pyrite and jasperoid quartz. Gold and pyrite precipitated together as H2S in the ore fluids reacted with iron in the host rocks. As ore fluids mixed with local aquifer fluids, ore fluids became cooler and more dilute. Cooling caused precipitation of ore-stage fluorite and orpiment, and late ore-stage realgar. Phase separation and/or neutralization of the ore fluid during the waning stages of the hydrothermal ore system led to deposition of late ore-stage calcite.

Manganese and ferromanganese ores from different tectonic settings in the NW Himalayas, Pakistan

NASA Astrophysics Data System (ADS)

Tahir Shah, Mohammad; Moon, Charles J.

2007-02-01

In Pakistan manganese and ferromanganese ores have been reported from the Hazara area of North West Frontier Province, Waziristan agencies in the Federally Administered Tribal Areas and the Lasbela-Khuzdar regions of Baluchistan. This study is focused on comparison of mineralogy and geochemistry of the continental ferromanganese ores of Hazara and the ophiolitic manganese ores of the Waziristan area of Pakistan. In the Hazara area, ferromanganese ores occur at Kakul, Galdanian and Chura Gali, near Abbottabad, within the Hazira Formation of the Kalachitta-Margala thrust belt of the NW Himalayas of the Indo-Pakistan Plate. The Cambrian Hazira Formation is composed of reddish-brown ferruginous siltstone, with variable amounts of clay, shale, ferromanganese ores, phosphorite and barite. In Waziristan, manganese ores occur at Shuidar, Mohammad Khel and Saidgi, within the Waziristan ophiolite complex, on the western margin of the Indo-Pakistan Plate in NW Pakistan. These banded and massive ores are hosted by metachert and overlie metavolcanics. The ferromanganese ores of the Hazara area contain variable amount of bixbyite, partridgeite, hollandite, pyrolusite and braunite. Bixbyite and partridgeite are the dominant Mn-bearing phases. Hematite dominates in Fe-rich ores. Gangue minerals are iron-rich clay, alumino-phosphate minerals, apatite, barite and glauconite are present in variable amounts, in both Fe-rich and Mn-rich varieties. The texture of the ore phases indicates greenschist facies metamorphism. The Waziristan ores are composed of braunite, with minor pyrolusite and hollandite. Hematite occurs as an additional minor phase in the Fe-rich ores of the Shuidar area. The only silicate phase in these ores is cryptocrystalline quartz. The chemical composition of the ferromanganese ores in Hazara suggests that the Mn-Fe was contributed by both hydrogenous and hydrothermal sources, while the manganese ores of Waziristan originated only from a hydrothermal source. It is suggested that the Fe-Mn ores of the Hazara area originated from a mixed hydrothermal-hydrogenetic source in shallow water in a ontinental shelf environment due to the transgression and regression of the sea, while the Mn ores of Waziristan were formed at sea-floor spreading centers within the Neo-Tethys Ocean, and were later obducted as part of the Waziristan ophiolite complex.

Trends and Solar Cycle Effects in Temperature Versus Altitude From the Halogen Occultation Experiment for the Mesosphere and Upper Stratosphere

NASA Technical Reports Server (NTRS)

Remsberg, Ellis E.

2009-01-01

Fourteen-year time series of mesospheric and upper stratospheric temperatures from the Halogen Occultation Experiment (HALOE) are analyzed and reported. The data have been binned according to ten-degree wide latitude zones from 40S to 40N and at 10 altitudes from 43 to 80 km-a total of 90 separate time series. Multiple linear regression (MLR) analysis techniques have been applied to those time series. This study focuses on resolving their 11-yr solar cycle (or SC-like) responses and their linear trend terms. Findings for T(z) from HALOE are compared directly with published results from ground-based Rayleigh lidar and rocketsonde measurements. SC-like responses from HALOE compare well with those from lidar station data at low latitudes. The cooling trends from HALOE also agree reasonably well with those from the lidar data for the concurrent decade. Cooling trends of the lower mesosphere from HALOE are not as large as those from rocketsondes and from lidar station time series of the previous two decades, presumably because the changes in the upper stratospheric ozone were near zero during the HALOE time period and did not affect those trends.

Subcellular Changes in Bridging Integrator 1 Protein Expression in the Cerebral Cortex During the Progression of Alzheimer Disease Pathology.

PubMed

Adams, Stephanie L; Tilton, Kathy; Kozubek, James A; Seshadri, Sudha; Delalle, Ivana

2016-08-01

Genome-wide association studies have established BIN1 (Bridging Integrator 1) as the most significant late-onset Alzheimer disease (AD) susceptibility locus after APOE We analyzed BIN1 protein expression using automated immunohistochemistry on the hippocampal CA1 region in 19 patients with either no, mild, or moderate-to-marked AD pathology, who had been assessed by Clinical Dementia Rating and CERAD scores. We also examined the amygdala, prefrontal, temporal, and occipital regions in a subset of these patients. In non-demented controls without AD pathology, BIN1 protein was expressed in white matter, glia, particularly oligodendrocytes, and in the neuropil in which the BIN1 signal decorated axons. With increasing severity of AD, BIN1 in the CA1 region showed: 1) sustained expression in glial cells, 2) decreased areas of neuropil expression, and 3) increased cytoplasmic neuronal expression that did not correlate with neurofibrillary tangle load. In patients with AD, both the prefrontal cortex and CA1 showed a decrease in BIN1-immunoreactive (BIN1-ir) neuropil areas and increases in numbers of BIN1-ir neurons. The numbers of CA1 BIN1-ir pyramidal neurons correlated with hippocampal CERAD neuritic plaque scores; BIN1 neuropil signal was absent in neuritic plaques. Our data provide novel insight into the relationship between BIN1 protein expression and the progression of AD-associated pathology and its diagnostic hallmarks. © 2016 American Association of Neuropathologists, Inc. All rights reserved.

Bin Ratio-Based Histogram Distances and Their Application to Image Classification.

PubMed

Hu, Weiming; Xie, Nianhua; Hu, Ruiguang; Ling, Haibin; Chen, Qiang; Yan, Shuicheng; Maybank, Stephen

2014-12-01

Large variations in image background may cause partial matching and normalization problems for histogram-based representations, i.e., the histograms of the same category may have bins which are significantly different, and normalization may produce large changes in the differences between corresponding bins. In this paper, we deal with this problem by using the ratios between bin values of histograms, rather than bin values' differences which are used in the traditional histogram distances. We propose a bin ratio-based histogram distance (BRD), which is an intra-cross-bin distance, in contrast with previous bin-to-bin distances and cross-bin distances. The BRD is robust to partial matching and histogram normalization, and captures correlations between bins with only a linear computational complexity. We combine the BRD with the ℓ1 histogram distance and the χ(2) histogram distance to generate the ℓ1 BRD and the χ(2) BRD, respectively. These combinations exploit and benefit from the robustness of the BRD under partial matching and the robustness of the ℓ1 and χ(2) distances to small noise. We propose a method for assessing the robustness of histogram distances to partial matching. The BRDs and logistic regression-based histogram fusion are applied to image classification. The experimental results on synthetic data sets show the robustness of the BRDs to partial matching, and the experiments on seven benchmark data sets demonstrate promising results of the BRDs for image classification.

High-rate behaviour of iron ore pellet

NASA Astrophysics Data System (ADS)

Gustafsson, Gustaf; Häggblad, Hans-Åke; Jonsén, Pär; Nishida, Masahiro

2015-09-01

Iron ore pellets are sintered, centimetre-sized spheres of ore with high iron content. Together with carbonized coal, iron ore pellets are used in the production of steel. In the transportation from the pelletizing plants to the customers, the iron ore pellets are exposed to different loading situations, resulting in degradation of strength and in some cases fragmentation. For future reliable numerical simulations of the handling and transportation of iron ore pellets, knowledge about their mechanical properties is needed. This paper describes the experimental work to investigate the dynamic mechanical properties of blast furnace iron ore pellets. To study the dynamic fracture of iron ore pellets a number of split Hopkinson pressure bar tests are carried out and analysed.

Igneous layering in the peralkaline intrusions ,Kola Peninsula :leading role of gravitational differentiation

NASA Astrophysics Data System (ADS)

Kogarko, L. N..

2012-04-01

In the center of Kola Peninsula there are two large layered intrusions of agpaitic nepheline syenites - Khibina and Lovozero. . The Khibina alkaline massif (Kola Peninsula,Russia) hosts the world's largest and economically most important apatite deposit. The Khibina massif is a complex multiphase body built up from a number of ring-like and conical intrusions. The apatite bearing intrusion is ring-like and is represented by a layered body of ijolitic composition with a thickness of about 1 - 2 km. The upper zone is represented by different types of apatite ores. These rocks consist of 60-90% euhedral very small (tenths of mm)apatite crystals. The lower zone has mostly ijolitic composition. The lower zone grades into underlying massive urtite consisting of 75-90% large (several mm) euhedral nepheline. Our experimental studies of systems with apatite demonstrated the near-eutectic nature of the apatite-bearing intrusion, resulting in practically simultaneous crystallization of nepheline, apatite and pyroxene. The mathematical model of the formation of the layered apatite-bearing intrusion based on the processes of sedimentation under the conditions of steady state convection taking account of crystal sizes is proposed. Under the conditions of steady-state convection large crystals of nepheline continuously had been settling forming massive underlying urtite whereas smaller crystals of pyroxenes, nepheline and apatite had been stirred in the convecting melt. During the cooling the intensity of convection decreased causing a settling of smaller crystals of nepheline and pyroxene and later very small crystalls of apatite in the upper part of alkaline magma chamber. The Lovozero massif, the largest of the Globe layered peralkaline intrusion, comprises super-large rare-metal (Nb, Ta, REE) deposit. The main ore mineral is loparite (Na, Ce, Ca)2 (Ti, Nb)2O6 which was mined during many years. The composition of cumulus loparite changed systematically upward through the intrusion with an increase in Na, Sr, Nb, Th, Nb/Ta, U/Th and decrease in REE, Zr, V, Zn, Ba and Ti. Our investigation indicates that the formation of loparite ore was the result of several factors including the chemical evolution of highly alkaline magmatic system and mechanical accumulation of loparite at the base of convecting unit.

Nature of parent rocks, mineralization styles and ore genesis of regolith-hosted REE deposits in South China: An integrated genetic model

NASA Astrophysics Data System (ADS)

Li, Yan Hei Martin; Zhao, Wen Winston; Zhou, Mei-Fu

2017-10-01

Regolith-hosted rare earth element (REE) deposits, also called ion-adsorption or weathered crust elution-deposited REE deposits are distributed over Jiangxi, Guangdong, Fujian, Hunan, Guangxi and Yunnan provinces in South China. In general, these deposits can be categorized into the HREE-dominated type, for example the famous Zudong deposit in southern Jiangxi province and the LREE-dominated type, such as the Heling and Dingnan deposits in southern Jiangxi province. Most of these deposits form from weathering of biotite and muscovite granites, syenites, monzogranites, granodiorites, granite porphyries, and rhyolitic tuffs. The parent rocks are generally peraluminous, siliceous, alkaline and contain a variety of REE-bearing minerals. Mostly, REE patterns of regolith are inherited from the parent rocks, and therefore, characteristics of the parent rocks impose a significant control on the ore formation. Data compilation shows that autometasomatism during the latest stage of granite crystallization is likely essential in forming the HREE-enriched granites, whereas LREE-enriched granites could form through magmatic differentiation. These deposits are normally two- to three-fold, but could be up to ten-fold enrichment in REE compared to the parent granites, where the maximum enrichment usually occurs from the lower B to the upper C horizon. Ce shows different behavior with the other REEs. Strongly positive Ce anomalies commonly occur at the upper part of weathering profiles, likely due to oxidation of Ce3+ to Ce4+ and removal of Ce from soil solutions through precipitation of cerianite. Vertical pH and redox gradients in weathering crusts facilitate dissolution of REE-bearing minerals at shallow level and fixation of REE at depth through either adsorption on clay minerals or precipitation of secondary minerals. At the same time, mass removal of major elements plays an important role in concentrating REE in regolith. Combination of mass removal and eluviation-illuviation dynamics is the main mechanism for REE accumulation in weathering crusts. Favorable exogenetic factors facilitate the accumulation of REE in regolith and preservation of the ore bodies. These include quasi-equilibrium between denudation and exhumation at regional scales, local geomorphology dominated by low-lying gentle slopes, adequate rainfall, and favorable groundwater conditions. Continuous operation of such a dynamic weathering system is essential in the formation of regolith-hosted REE deposits.

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

Potential fitting biases resulting from grouping data into variable width bins

NASA Astrophysics Data System (ADS)

Towers, S.

2014-07-01

When reading peer-reviewed scientific literature describing any analysis of empirical data, it is natural and correct to proceed with the underlying assumption that experiments have made good faith efforts to ensure that their analyses yield unbiased results. However, particle physics experiments are expensive and time consuming to carry out, thus if an analysis has inherent bias (even if unintentional), much money and effort can be wasted trying to replicate or understand the results, particularly if the analysis is fundamental to our understanding of the universe. In this note we discuss the significant biases that can result from data binning schemes. As we will show, if data are binned such that they provide the best comparison to a particular (but incorrect) model, the resulting model parameter estimates when fitting to the binned data can be significantly biased, leading us to too often accept the model hypothesis when it is not in fact true. When using binned likelihood or least squares methods there is of course no a priori requirement that data bin sizes need to be constant, but we show that fitting to data grouped into variable width bins is particularly prone to produce biased results if the bin boundaries are chosen to optimize the comparison of the binned data to a wrong model. The degree of bias that can be achieved simply with variable binning can be surprisingly large. Fitting the data with an unbinned likelihood method, when possible to do so, is the best way for researchers to show that their analyses are not biased by binning effects. Failing that, equal bin widths should be employed as a cross-check of the fitting analysis whenever possible.

10 CFR 40.23 - General license for carriers of transient shipments of natural uranium other than in the form of...

Code of Federal Regulations, 2012 CFR

2012-01-01

... natural uranium other than in the form of ore or ore residue. 40.23 Section 40.23 Energy NUCLEAR... carriers of transient shipments of natural uranium other than in the form of ore or ore residue. (a) A... than in the form of ore or ore residue, in amounts exceeding 500 kilograms. (b)(1) Persons generally...

10 CFR 40.23 - General license for carriers of transient shipments of natural uranium other than in the form of...

Code of Federal Regulations, 2011 CFR

2011-01-01

... natural uranium other than in the form of ore or ore residue. 40.23 Section 40.23 Energy NUCLEAR... carriers of transient shipments of natural uranium other than in the form of ore or ore residue. (a) A... than in the form of ore or ore residue, in amounts exceeding 500 kilograms. (b)(1) Persons generally...

10 CFR 40.23 - General license for carriers of transient shipments of natural uranium other than in the form of...

Code of Federal Regulations, 2013 CFR

2013-01-01

... natural uranium other than in the form of ore or ore residue. 40.23 Section 40.23 Energy NUCLEAR... carriers of transient shipments of natural uranium other than in the form of ore or ore residue. (a) A... than in the form of ore or ore residue, in amounts exceeding 500 kilograms. (b)(1) Persons generally...

10 CFR 40.23 - General license for carriers of transient shipments of natural uranium other than in the form of...

Code of Federal Regulations, 2014 CFR

2014-01-01

... natural uranium other than in the form of ore or ore residue. 40.23 Section 40.23 Energy NUCLEAR... carriers of transient shipments of natural uranium other than in the form of ore or ore residue. (a) A... than in the form of ore or ore residue, in amounts exceeding 500 kilograms. (b)(1) Persons generally...

Effects of Mixtures on Liquid and Solid Fragment Size Distributions

DTIC Science & Technology

2016-05-01

bins, too few size bins, fixed bin widths, or inadequately- varying bin widths. Overpopulated bins – which typically occur for smaller fragments...2010 C. V. B. Cunningham, The Kuz-Ram Fragmentation Model – 20 Years On, In R. Holmberg et. al., Editors, Proceedings of the 3 rd World ...1992 P. K. Sahoo and T. Riedel, Mean Value Theorems and Functional Equations, World Scientific, 1998 K. A. Sallam, C. Aalburg, G.M. Faeth

BIN1 is reduced and Cav1.2 trafficking is impaired in human failing cardiomyocytes.

PubMed

Hong, Ting-Ting; Smyth, James W; Chu, Kevin Y; Vogan, Jacob M; Fong, Tina S; Jensen, Brian C; Fang, Kun; Halushka, Marc K; Russell, Stuart D; Colecraft, Henry; Hoopes, Charles W; Ocorr, Karen; Chi, Neil C; Shaw, Robin M

2012-05-01

Heart failure is a growing epidemic, and a typical aspect of heart failure pathophysiology is altered calcium transients. Normal cardiac calcium transients are initiated by Cav1.2 channels at cardiac T tubules. Bridging integrator 1 (BIN1) is a membrane scaffolding protein that causes Cav1.2 to traffic to T tubules in healthy hearts. The mechanisms of Cav1.2 trafficking in heart failure are not known. To study BIN1 expression and its effect on Cav1.2 trafficking in failing hearts. Intact myocardium and freshly isolated cardiomyocytes from nonfailing and end-stage failing human hearts were used to study BIN1 expression and Cav1.2 localization. To confirm Cav1.2 surface expression dependence on BIN1, patch-clamp recordings were performed of Cav1.2 current in cell lines with and without trafficking-competent BIN1. Also, in adult mouse cardiomyocytes, surface Cav1.2 and calcium transients were studied after small hairpin RNA-mediated knockdown of BIN1. For a functional readout in intact heart, calcium transients and cardiac contractility were analyzed in a zebrafish model with morpholino-mediated knockdown of BIN1. BIN1 expression is significantly decreased in failing cardiomyocytes at both mRNA (30% down) and protein (36% down) levels. Peripheral Cav1.2 is reduced to 42% by imaging, and a biochemical T-tubule fraction of Cav1.2 is reduced to 68%. The total calcium current is reduced to 41% in a cell line expressing a nontrafficking BIN1 mutant. In mouse cardiomyocytes, BIN1 knockdown decreases surface Cav1.2 and impairs calcium transients. In zebrafish hearts, BIN1 knockdown causes a 75% reduction in calcium transients and severe ventricular contractile dysfunction. The data indicate that BIN1 is significantly reduced in human heart failure, and this reduction impairs Cav1.2 trafficking, calcium transients, and contractility. Copyright © 2012 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

BIN1 is Reduced and Cav1.2 Trafficking is Impaired in Human Failing Cardiomyocytes

PubMed Central

Hong, Ting-Ting; Smyth, James W.; Chu, Kevin Y.; Vogan, Jacob M.; Fong, Tina S.; Jensen, Brian C.; Fang, Kun; Halushka, Marc K.; Russell, Stuart D.; Colecraft, Henry; Hoopes, Charles W.; Ocorr, Karen; Chi, Neil C.; Shaw, Robin M.

2011-01-01

Background Heart failure is a growing epidemic and a typical aspect of heart failure pathophysiology is altered calcium transients. Normal cardiac calcium transients are initiated by Cav1.2 channels at cardiac T-tubules. BIN1 is a membrane scaffolding protein that causes Cav1.2 to traffic to T-tubules in healthy hearts. The mechanisms of Cav1.2 trafficking in heart failure are not known. Objective To study BIN1 expression and its effect on Cav1.2 trafficking in failing hearts. Methods Intact myocardium and freshly isolated cardiomyocytes from non-failing and end-stage failing human hearts were used to study BIN1 expression and Cav1.2 localization. To confirm Cav1.2 surface expression dependence on BIN1, patch clamp recordings were performed of Cav1.2 current in cell lines with and without trafficking competent BIN1. Also, in adult mouse cardiomyocytes, surface Cav1.2 and calcium transients were studied after shRNA mediated knockdown of BIN1. For a functional readout in intact heart, calcium transients and cardiac contractility were analyzed in a zebrafish model with morpholino mediated knockdown of BIN1. Results BIN1 expression is significantly decreased in failing cardiomyocytes at both mRNA (30% down) and protein (36% down) levels. Peripheral Cav1.2 is reduced 42% by imaging and biochemical T-tubule fraction of Cav1.2 is reduced 68%. Total calcium current is reduced 41% in a cell line expressing non-trafficking BIN1 mutant. In mouse cardiomyocytes, BIN1 knockdown decreases surface Cav1.2 and impairs calcium transients. In zebrafish hearts, BIN1 knockdown causes a 75% reduction in calcium transients and severe ventricular contractile dysfunction. Conclusions The data indicate that BIN1 is significantly reduced in human heart failure, and this reduction impairs Cav1.2 trafficking, calcium transients, and contractility. PMID:22138472

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The provisions of this...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The provisions of this...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions of this subpart...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The provisions of this...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The provisions of this...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The provisions of this...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions of this subpart...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions of subpart D...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The provisions of this...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The provisions of this...

The impact of periglacial cover beds on runoff generation in a small spring catchment, Ore Mountains

NASA Astrophysics Data System (ADS)

Heller, Katja; Hübner, Rico; Kleber, Arno

2010-05-01

The knowledge of hillslope processes is essential to improve pollutant research and flood prediction. Relic periglacial covers are widespread on slopes of the central European low mountain ranges. Cover beds are assumed to be an important control factor for subcutaneous water flow paths. Periglacial cover beds originated by solifluction, kryoturbation and accumulation of loess during Pleistocene times. Differences in bulk density, sediment type, as well as structure and rate of coarse clasts in the layers result in vertical disparity in hydraulic conductivity (anisotropy), leading to interflow. This hypothesis has been testing in an ongoing study in a small spring catchment (6 ha) in the eastern Ore Mountains, south-eastern Germany, since November 2007. The study area is underlain by gneiss and is formed as a slope hollow. The cover beds consist of a 3-layer complex with upper layer, intermediate layer and basal layer. Soil water tension within the layers is measured with 76 recording tensiometers. Electrical resistivity tomography was used to monitor the spatial dispersal of soil moisture. Results of hydrometrical measurements and of electrical resistivity surveys will be described and new findings on slope water dynamics will be presented.

An overview of the association between lamprophyric intrusions and rare-metal mineralization

NASA Astrophysics Data System (ADS)

Štemprok, Miroslav; Seifert, Thomas

2011-01-01

Granite-related rare metal districts in orogenic settings are occasionally associated with lamprophyre dikes. We recorded 63 occurrences of lamprophyres in bimodal dike suites of about 200 granite bodies related to rare metal deposits. Most lamprophyres occur in Paleozoic and Mesozoic metallogenic provinces in the northern hemisphere. Lamprophyres which are associated with rare metal deposits are calc-alkaline (kersantites, minettes, spessartites) or more rarely alkaline lamprophyres (camptonites, monchiquites) which occur in the roof zone of complex granitic bodies as pre-granitic, intra-granitic, intra-ore or post-ore dikes. Most lamprophyres are spatially associated with dominant felsic dikes and/or with mafic dikes represented by diorites or diabases. Diorites and lamprophyres occasionally exhibit transitional compositions from one to another. Lamprophyres share common geochemical characteristics of highly evolved granitoids such as enrichment in K and F, increased abundances of Li, Rb, and Cs and enrichment in some HFSE (e.g. Zr, U, Th, Mo, Sn, W). Lamprophyres in rare metal districts testify to accessibility of the upper crust to mantle products at the time of rare metal mineralization and possible influence of mantle melts or mantle-derived fluids in the differentiation of granitic melts in the lower crust.

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

36. ORE DOCK, LOOKING WEST. HULETT UNLOADERS AWAIT THE NEXT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. ORE DOCK, LOOKING WEST. HULETT UNLOADERS AWAIT THE NEXT ORE BOAT. BY LATE WINTER, THE ORE STORAGE YARD SEEN AT LEFT WILL BE DEPLETED. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the vanadium ore...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the vanadium ore...

The Problem of Preconcentration of Uranium Ores by Physical Processes; LES PROBLEMES DE LA PRECONCENTRATION DES MINERAIS D'URANIUM PAR VOIE PHYSIQUE. LE TRIAGE ELECTRONIQUE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuchot, L.; Ginocchio, A. et al.

1959-10-31

As uranium ores, like most other ores, are not definite substances which can be treated directly for the production of the metal, the ores must be concentrated. The common physical processes used for all ores, such as sieving, gravimetric separation, flotation, electromagnetic separation, and electrostatic separation, are applicable to the beneficiation of uranium. The radioactivity of uranium ores has led to a radiometric method for the concentration. This method is described in detail. As an example, the preconcentration of Forez ores is discussed. (J.S.R.)

BusyBee Web: metagenomic data analysis by bootstrapped supervised binning and annotation

PubMed Central

Kiefer, Christina; Fehlmann, Tobias; Backes, Christina

2017-01-01

Abstract Metagenomics-based studies of mixed microbial communities are impacting biotechnology, life sciences and medicine. Computational binning of metagenomic data is a powerful approach for the culture-independent recovery of population-resolved genomic sequences, i.e. from individual or closely related, constituent microorganisms. Existing binning solutions often require a priori characterized reference genomes and/or dedicated compute resources. Extending currently available reference-independent binning tools, we developed the BusyBee Web server for the automated deconvolution of metagenomic data into population-level genomic bins using assembled contigs (Illumina) or long reads (Pacific Biosciences, Oxford Nanopore Technologies). A reversible compression step as well as bootstrapped supervised binning enable quick turnaround times. The binning results are represented in interactive 2D scatterplots. Moreover, bin quality estimates, taxonomic annotations and annotations of antibiotic resistance genes are computed and visualized. Ground truth-based benchmarks of BusyBee Web demonstrate comparably high performance to state-of-the-art binning solutions for assembled contigs and markedly improved performance for long reads (median F1 scores: 70.02–95.21%). Furthermore, the applicability to real-world metagenomic datasets is shown. In conclusion, our reference-independent approach automatically bins assembled contigs or long reads, exhibits high sensitivity and precision, enables intuitive inspection of the results, and only requires FASTA-formatted input. The web-based application is freely accessible at: https://ccb-microbe.cs.uni-saarland.de/busybee. PMID:28472498

Variation of Equatorial F-region Vertical Neutral Wind and Neutral Temperature during Geomagnetic Storms: Brazil FPI Observations

NASA Astrophysics Data System (ADS)

Sheng, C.; De La Garza, J. L.; Deng, Y.; Makela, J. J.; Fisher, D. J.; Meriwether, J. W.; Mesquita, R.

2015-12-01

An accurate description of vertical neutral winds in the thermosphere is essential to understand how the upper atmosphere responds to the geomagnetic storms. However, vertical wind measurements are difficult to obtain and there are still limited data. Recent observation deployments now permit substantial progress on this issue. In this paper, neutral vertical wind data from Brazil FPI observations at around 240 km altitude during 2009 to 2015 are used for the study of the equatorial vertical wind and neutral temperature variation during geomagnetic activity times. First, the observations during several particular storm periods will be analyzed. Secondly, Epoch analysis will be used to bin all the observed events together to investigate the climatological features of vertical wind and temperature during storms. The results will give us an unprecedented view of the nighttime vertical wind and neutral temperature variations at low latitudes, which is critical to specify the dynamics of the upper atmosphere.

Solvent extraction of diatomite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, W.

1984-07-24

There is provided a method of extracting hydrocarbons from a diatomite ore. The particle size of the ore is first reduced to form a processed ore. The processed ore is then mixed with a substantially irregular granular material to form an unstratified ore mixture having increased permeability to an extracting solvent. The unstratified ore mixture is then permeated with an extracting solvent to obtain a hydrocarbon-solvent stream from which hydrocarbons are subsequently separated. The irregular granular material may be sand.

A Hierarchical Modeling Study of the Interactions Among Turbulence, Cloud Microphysics, and Radiative Transfer in the Evolution of Cirrus Clouds

NASA Technical Reports Server (NTRS)

Curry, Judith; Khvorostyanov, V. I.

2005-01-01

This project used a hierarchy of cloud resolving models to address the following science issues of relevance to CRYSTAL-FACE: What ice crystal nucleation mechanisms are active in the different types of cirrus clouds in the Florida area and how do these different nucleation processes influence the evolution of the cloud system and the upper tropospheric humidity? How does the feedback between supersaturation and nucleation impact the evolution of the cloud? What is the relative importance of the large-scale vertical motion and the turbulent motions in the evolution of the crystal size spectra? How does the size spectra impact the life-cycle of the cloud, stratospheric dehydration, and cloud radiative forcing? What is the nature of the turbulence and waves in the upper troposphere generated by precipitating deep convective cloud systems? How do cirrus microphysical and optical properties vary with the small-scale dynamics? How do turbulence and waves in the upper troposphere influence the cross-tropopause mixing and stratospheric and upper tropospheric humidity? The models used in this study were: 2-D hydrostatic model with explicit microphysics that can account for 30 size bins for both the droplet and crystal size spectra. Notably, a new ice crystal nucleation scheme has been incorporated into the model. Parcel model with explicit microphysics, for developing and evaluating microphysical parameterizations. Single column model for testing bulk microphysics parameterizations

25. FRONT END LOADERS MOMENTARILY IN REPOSE IN THE ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. FRONT END LOADERS MOMENTARILY IN REPOSE IN THE ORE STORAGE YARD. AN ORE BRIDGE THAT FORMERLY TRANSFERRED ORE WITHIN THE STORAGE YARD WAS DESTROYED BY A BLIZZARD IN 1978. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

38. HULETT ORE UNLOADERS IN MOTION; UNLOADING CANADIAN RED ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. HULETT ORE UNLOADERS IN MOTION; UNLOADING CANADIAN RED ORE FROM THE GEORGE M. CARL.' VIEW LOOKING EAST. (Also see OH-18-14, OH-18-39, and OH-18-40) - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

14. HULETT ORE UNLOADERS IN MOTION; UNLOADING CANADIAN RED ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. HULETT ORE UNLOADERS IN MOTION; UNLOADING CANADIAN RED ORE FROM THE 'GEORGE M. CAR.' VIEW LOOKING EAST. (Also see OH-18-38, OH-18-39, and OH-18-40.) - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Carbon Characteristics and Biogeochemical Processes of Uranium Accumulating Organic Matter Rich Sediments in the Upper Colorado River Basin

NASA Astrophysics Data System (ADS)

Boye, K.; Noel, V.; Tfaily, M. M.; Dam, W. L.; Bargar, J.; Fendorf, S. E.

2015-12-01

Uranium plume persistence in groundwater aquifers is a problem on several former ore processing sites on floodplains in the upper Colorado River Basin. Earlier observations by our group and others at the Old Rifle Site, CO, have noted that U concentrations are highest in organic rich, fine-grained, and, therefore, diffusion limited sediment material. Due to the constantly evolving depositional environments of floodplains, surficial organic matter may become buried at various stages of decomposition, through sudden events such as overbank flooding and through the slower progression of river meandering. This creates a discontinuous subsurface distribution of organic-rich sediments, which are hotspots for microbial activity and thereby central to the subsurface cycling of contaminants (e.g. U) and biologically relevant elements (e.g. C, N, P, Fe). However, the organic matter itself is poorly characterized. Consequently, little is known about its relevance in driving biogeochemical processes that control U fate and transport in the subsurface. In an investigation of soil/sediment cores from five former uranium ore processing sites on floodplains distributed across the Upper Colorado River Basin we confirmed consistent co-enrichment of U with organic-rich layers in all profiles. However, using C K-edge X-ray Absorption Spectroscopy (XAS) coupled with Fourier-Transformed Ion-Cyclotron-Resonance Mass-Spectroscopy (FT-ICR-MS) on bulk sediments and density-separated organic matter fractions, we did not detect any chemical difference in the organic rich sediments compared to the surrounding coarser-grained aquifer material within the same profile, even though there were differences in organic matter composition between the 5 sites. This suggests that U retention and reduction to U(IV) is independent of C chemical composition on the bulk scale. Instead it appears to be the abundance of organic matter in combination with a limited O2 supply in the fine-grained material that stimulate anaerobic microbial processes responsible for U enrichment. Thus, the chemical composition of organic matter is subordinate to the physical environment and total organic matter content in controlling U reduction and retention processes.

A unique ore-placer cluster with high-Hg gold mineralization in the Amur region (Russia)

NASA Astrophysics Data System (ADS)

Stepanov, V. A.; Moyseenko, V. G.; Melnikov, A. V.

2017-02-01

This work presents the geological structure and a description of gold-ore manifestations and gold placers in the Un'ya-Bom ore-placer cluster of the Amur gold-bearing province. The host rocks are Late Paleozoic and Mesozoic black-shale formations. Intrusive formations are rare. The sublatitudinal Un'ya thrust fault, along which Paleozoic sandstones overlap Mesozoic flyschoid deposits, is regarded as an orecontrolling structure. Gold-quartz and low-sulfide ores are confined to quartz-vein zones. Ore minerals are arsenopyrite, scheelite, ferberite, galena, and native gold. Gold-ore manifestations and placers contain high-Hg native gold. The high Hg content in native gold is explained by the occurrence of the eroded frontal part of the gold-ore pipe in the ore cluster, a source of native gold.

Mining legacy across a wetland landscape: high mercury in Upper Peninsula (Michigan) rivers, lakes, and fish.

PubMed

Kerfoot, W Charles; Urban, Noel R; McDonald, Cory P; Zhang, Huanxin; Rossmann, Ronald; Perlinger, Judith A; Khan, Tanvir; Hendricks, Ashley; Priyadarshini, Mugdha; Bolstad, Morgan

2018-04-25

A geographic enigma is that present-day atmospheric deposition of mercury in the Upper Peninsula of Michigan is low (48%) and that regional industrial emissions have declined substantially (ca. 81% reduction) relative to downstate. Mercury levels should be declining. However, state (MDEQ) surveys of rivers and lakes revealed elevated total mercury (THg) in Upper Peninsula waters and sediment relative to downstate. Moreover, Western Upper Peninsula (WUP) fish possess higher methyl mercury (MeHg) levels than Northern Lower Peninsula (NLP) fish. A contributing explanation for elevated THg loading is that a century ago the Upper Peninsula was a major industrial region, centered on mining. Many regional ores (silver, copper, zinc, massive sulfides) contain mercury in part per million concentrations. Copper smelters and iron furnace-taconite operations broadcast mercury almost continuously for 140 years, whereas mills discharged tailings and old mine shafts leaked contaminated water. We show that mercury emissions from copper and iron operations were substantial (60-650 kg per year) and dispersed over relatively large areas. Moreover, lake sediments in the vicinity of mining operations have higher THg concentrations. Sediment profiles from the Keweenaw Waterway show that THg accumulation increased 50- to 400-fold above modern-day atmospheric deposition levels during active mining and smelting operations, with lingering MeHg effects. High MeHg concentrations are geographically correlated with low pH and dissolved organic carbon (DOC), a consequence of biogeochemical cycling in wetlands, characteristic of the Upper Peninsula. DOC can mobilize metals and elevate MeHg concentrations. We argue that mercury loading from mining is historically superimposed upon strong regional wetland effects, producing a combined elevation of both THg and MeHg in the Western Upper Peninsula.

Blasting preparation for selective mining of complex structured ore deposition

NASA Astrophysics Data System (ADS)

Marinin, M. A.; Dolzhikov, V. V.

2017-10-01

Technological features of ore mining in the open pit development for processing of complex structured ore deposit of steeply falling occurrence have been considered. The technological schemes of ore bodies mining under different conditions of occurrence, consistency and capacity have been considered and offered in the paper. These technologies permit to reduce losses and dilution, but to increase the completeness and quality of mined ore. A method of subsequent selective excavation of ore bodies has been proposed. The method is based on the complex use of buffer-blasting technology for the muck mass and the principle of trim blasting at ore-rock junctions.

30 CFR 57.16002 - Bins, hoppers, silos, tanks, and surge piles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Bins, hoppers, silos, tanks, and surge piles... NONMETAL MINES Materials Storage and Handling § 57.16002 Bins, hoppers, silos, tanks, and surge piles. (a) Bins, hoppers, silos, tanks, and surge piles, where loose unconsolidated materials are stored, handled...

30 CFR 56.16002 - Bins, hoppers, silos, tanks, and surge piles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Bins, hoppers, silos, tanks, and surge piles... MINES Materials Storage and Handling § 56.16002 Bins, hoppers, silos, tanks, and surge piles. (a) Bins, hoppers, silos, tanks, and surge piles, where loose unconsolidated materials are stored, handled or...

Pack Factor Measurementss for Corn in Grain Storage Bins

USDA-ARS?s Scientific Manuscript database

Grain is commonly stored commercially in tall bins, which often are as deep as 35 m (114.8 ft) for tall and narrow concrete bins and about 32 m (105 ft) in diameter for large corrugated steel bins. Grain can support the great pressure without crushing, but it yields somewhat to compaction under its ...

Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system.

PubMed

Hannan, M A; Arebey, Maher; Begum, R A; Basri, Hassan

2011-12-01

This paper deals with a system of integration of Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system. RFID, GPS, GPRS and GIS along with camera technologies have been integrated and developed the bin and truck intelligent monitoring system. A new kind of integrated theoretical framework, hardware architecture and interface algorithm has been introduced between the technologies for the successful implementation of the proposed system. In this system, bin and truck database have been developed such a way that the information of bin and truck ID, date and time of waste collection, bin status, amount of waste and bin and truck GPS coordinates etc. are complied and stored for monitoring and management activities. The results showed that the real-time image processing, histogram analysis, waste estimation and other bin information have been displayed in the GUI of the monitoring system. The real-time test and experimental results showed that the performance of the developed system was stable and satisfied the monitoring system with high practicability and validity. Copyright © 2011 Elsevier Ltd. All rights reserved.

The solubility of gallium oxide in vapor and two-phase fluid filtration in hydrothermal systems

NASA Astrophysics Data System (ADS)

Bychkov, Andrew; Matveeva, Svetlana; Nekrasov, Stanislav

2010-05-01

The solubility of gallium and aluminum oxides in gas phase in the system Ga2O3 (Al2O3)-HCl-H2O was studied at 150-350°C and pressure up to saturated vapor. The concentration of gallium increases with the increasing of HCl pressure. The formulae of gallium gaseous specie was determined as GaOHCl2. The constant of gallium oxide solubility reaction was calculated at 150, 200, 250, 300 and 350°C. The concentration of aluminum in gas phase is insignificant in the same conditions. The possibility of gallium transportation in gas phase with small quantity of Al allow to divide this elements in hydrothermal processes with gas phase. The Ga/Al ratio in muscovite can be used as the indicator of gas phase separation and condensation. This indicator was not considered in the geochemical literature earlier. The separation of gas and liquid phases was determined in Akchatau (Kazahstan) and Spokoinoe (Russia) greisen W deposit by carbon isotope fractionation of carbon dioxide in fluid inclusion. The important feature of both ore mains is heterogenization and boiling of ore-forming fluids. Greisen ore bodies are formed as a result of strongly focused solution flow in the T-P gradient fields. It is possible to divide ore bodies of Akchatau in two types: muscovite and quartz. Muscovite type veins are thin and have small metasyntactic zone. Quartz type veins are localized in fault with large vertical extent (500 m) and content the large quantity of wolframite. These veins formed in condition of significant pressure decreasing from 2.5 to 0.5 kbar with fluid boiling. Gas and liquid phase separation specifies the vertical zonality of quartz type veins. The gas phase with the high gallium concentration is separated from a flow of liquid phase. Liquid phase react with the granites forming greisen metasomatites. Condensation of the gas phase in upper parts of massive produces the increasing of Ga/Al ratio in muscovite 3-5 times more, then in granites and bottom part of vein (from 2×10-4 to 8×10-4 mass ratio). The muscovite type veins has no separation between gas and liquid due to there thickness and small pressure gradient. There is no difference in Ga/Al ratio in muscovite from this veins. The Spokoinoe deposit is classified by mineralized dome type. The heterogenization of fluid occurs in H2O-CO2 system for water phase and carbon dioxide with temperature decreasing. Two-phase flow is separated in granite, forming greisen metosomatites. The Ga/Al ratio in rock increase up to 3 times to the upper part of metasomatitic zone. The Ga/Al ratio in muscovite can be applied for other hydrothermal systems for geochemical indicator of gas phase separation and condensation zone determination. This work is supported by RFBR project 10-05-00670 and 10-05-00320.

46 CFR 97.12-1 - Bulk ores and similar cargoes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Bulk ores and similar cargoes. 97.12-1 Section 97.12-1... OPERATIONS Cargo Stowage § 97.12-1 Bulk ores and similar cargoes. (a) The owners or operators of general cargo vessels which carry bulk cargoes such as ore, ore concentrates, and similar cargoes shall furnish...

MBMC: An Effective Markov Chain Approach for Binning Metagenomic Reads from Environmental Shotgun Sequencing Projects.

PubMed

Wang, Ying; Hu, Haiyan; Li, Xiaoman

2016-08-01

Metagenomics is a next-generation omics field currently impacting postgenomic life sciences and medicine. Binning metagenomic reads is essential for the understanding of microbial function, compositions, and interactions in given environments. Despite the existence of dozens of computational methods for metagenomic read binning, it is still very challenging to bin reads. This is especially true for reads from unknown species, from species with similar abundance, and/or from low-abundance species in environmental samples. In this study, we developed a novel taxonomy-dependent and alignment-free approach called MBMC (Metagenomic Binning by Markov Chains). Different from all existing methods, MBMC bins reads by measuring the similarity of reads to the trained Markov chains for different taxa instead of directly comparing reads with known genomic sequences. By testing on more than 24 simulated and experimental datasets with species of similar abundance, species of low abundance, and/or unknown species, we report here that MBMC reliably grouped reads from different species into separate bins. Compared with four existing approaches, we demonstrated that the performance of MBMC was comparable with existing approaches when binning reads from sequenced species, and superior to existing approaches when binning reads from unknown species. MBMC is a pivotal tool for binning metagenomic reads in the current era of Big Data and postgenomic integrative biology. The MBMC software can be freely downloaded at http://hulab.ucf.edu/research/projects/metagenomics/MBMC.html .

Bin-Hash Indexing: A Parallel Method for Fast Query Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bethel, Edward W; Gosink, Luke J.; Wu, Kesheng

2008-06-27

This paper presents a new parallel indexing data structure for answering queries. The index, called Bin-Hash, offers extremely high levels of concurrency, and is therefore well-suited for the emerging commodity of parallel processors, such as multi-cores, cell processors, and general purpose graphics processing units (GPU). The Bin-Hash approach first bins the base data, and then partitions and separately stores the values in each bin as a perfect spatial hash table. To answer a query, we first determine whether or not a record satisfies the query conditions based on the bin boundaries. For the bins with records that can not bemore » resolved, we examine the spatial hash tables. The procedures for examining the bin numbers and the spatial hash tables offer the maximum possible level of concurrency; all records are able to be evaluated by our procedure independently in parallel. Additionally, our Bin-Hash procedures access much smaller amounts of data than similar parallel methods, such as the projection index. This smaller data footprint is critical for certain parallel processors, like GPUs, where memory resources are limited. To demonstrate the effectiveness of Bin-Hash, we implement it on a GPU using the data-parallel programming language CUDA. The concurrency offered by the Bin-Hash index allows us to fully utilize the GPU's massive parallelism in our work; over 12,000 records can be simultaneously evaluated at any one time. We show that our new query processing method is an order of magnitude faster than current state-of-the-art CPU-based indexing technologies. Additionally, we compare our performance to existing GPU-based projection index strategies.« less

Intensification of the Reverse Cationic Flotation of Hematite Ores with Optimization of Process and Hydrodynamic Parameters of Flotation Cell

NASA Astrophysics Data System (ADS)

Poperechnikova, O. Yu; Filippov, L. O.; Shumskaya, E. N.; Filippova, I. V.

2017-07-01

The demand of high grade iron ore concentrates is a major issue due to the depletion of rich iron-bearing ores and high competitiveness in the iron ore market. Iron ore production is forced out to upgrade flowsheets to decrease the silica content in the pelettes. Different types of ore have different mineral composition and texture-structural features which require different mineral processing methods and technologies. The paper presents a comparative study of the cationic and anionic flotation routes to process a fine-grain oxidized iron ore. The modified carboxymethyl cellulose was found as the most efficient depressant in reverse cationic flotation. The results of flotation optimization of hematite ores using matrix of second-order center rotatable uniform design allowed to define the collector concentration, impeller rotation speed and air flowrate as the main flotation parameters impacting on the iron ore concentrate quality and iron recovery in a laboratory flotation machine. These parameters have been selected as independent during the experiments.

SU-F-J-135: Tumor Displacement-Based Binning for Respiratory-Gated Time-Independent 5DCT Treatment Planning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, L; O’Connell, D; Lee, P

2016-06-15

Purpose: A published 5DCT breathing motion model enables image reconstruction at any user-selected breathing phase, defined by the model as a specific amplitude (v) and rate (f). Generation of reconstructed phase-specific CT scans will be required for time-independent radiation dose distribution simulations. This work answers the question: how many amplitude and rate bins are required to describe the tumor motion with a specific spatial resolution? Methods: 19 lung-cancer patients with 21 tumors were scanned using a free-breathing 5DCT protocol, employing an abdominally positioned pneumatic-bellows breathing surrogate and yielding voxel-specific motion model parameters α and β corresponding to motion as amore » function of amplitude and rate, respectively. Tumor GTVs were contoured on the first (reference) of 25 successive free-breathing fast helical CT image sets. The tumor displacements were binned into widths of 1mm to 5mm in 1mm steps and the total required number of bins recorded. The simulation evaluated the number of bins needed to encompass 100% of the breathing-amplitude and between the 5th and 95th percentile amplitudes to exclude breathing outliers. Results: The mean respiration-induced tumor motion was 9.90mm ± 7.86mm with a maximum of 25mm. The number of bins required was a strong function of the spatial resolution and varied widely between patients. For example, for 2mm bins, between 1–13 amplitude bins and 1–9 rate bins were required to encompass 100% of the breathing amplitude, while 1–6 amplitude bins and 1–3 rate bins were required to encompass 90% of the breathing amplitude. Conclusion: The strong relationship between number of bins and spatial resolution as well as the large variation between patients implies that time-independent radiation dose distribution simulations should be conducted using patient-specific data and that the breathing conditions will have to be carefully considered. This work will lead to the assessment of the dosimetric impact of binning resolution. This study is supported by Siemens Healthcare.« less

Data-driven optimal binning for respiratory motion management in PET.

PubMed

Kesner, Adam L; Meier, Joseph G; Burckhardt, Darrell D; Schwartz, Jazmin; Lynch, David A

2018-01-01

Respiratory gating has been used in PET imaging to reduce the amount of image blurring caused by patient motion. Optimal binning is an approach for using the motion-characterized data by binning it into a single, easy to understand/use, optimal bin. To date, optimal binning protocols have utilized externally driven motion characterization strategies that have been tuned with population-derived assumptions and parameters. In this work, we are proposing a new strategy with which to characterize motion directly from a patient's gated scan, and use that signal to create a patient/instance-specific optimal bin image. Two hundred and nineteen phase-gated FDG PET scans, acquired using data-driven gating as described previously, were used as the input for this study. For each scan, a phase-amplitude motion characterization was generated and normalized using principle component analysis. A patient-specific "optimal bin" window was derived using this characterization, via methods that mirror traditional optimal window binning strategies. The resulting optimal bin images were validated by correlating quantitative and qualitative measurements in the population of PET scans. In 53% (n = 115) of the image population, the optimal bin was determined to include 100% of the image statistics. In the remaining images, the optimal binning windows averaged 60% of the statistics and ranged between 20% and 90%. Tuning the algorithm, through a single acceptance window parameter, allowed for adjustments of the algorithm's performance in the population toward conservation of motion or reduced noise-enabling users to incorporate their definition of optimal. In the population of images that were deemed appropriate for segregation, average lesion SUV max were 7.9, 8.5, and 9.0 for nongated images, optimal bin, and gated images, respectively. The Pearson correlation of FWHM measurements between optimal bin images and gated images were better than with nongated images, 0.89 and 0.85, respectively. Generally, optimal bin images had better resolution than the nongated images and better noise characteristics than the gated images. We extended the concept of optimal binning to a data-driven form, updating a traditionally one-size-fits-all approach to a conformal one that supports adaptive imaging. This automated strategy was implemented easily within a large population and encapsulated motion information in an easy to use 3D image. Its simplicity and practicality may make this, or similar approaches ideal for use in clinical settings. © 2017 American Association of Physicists in Medicine.

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore... are applicable to discharges from (a) mines, either open-pit or underground, that produce mercury ores...

The USGS Abandoned Mine Lands Initiative: Protecting and restoring the environment near abandoned mine lands

USGS Publications Warehouse

,

1999-01-01

The Abandoned Mine Lands (AML) Initiative is part of a larger strategy of the U.S. Department of the Interior and the U.S. Department of Agriculture to clean up Federal lands contaminated by abandoned mines.Thousands of abandond hard-rock metal mines (such as gold, copper, lead, and zinc) have left a dual legacy across the Western United States. They reflect the historic development of the west, yet at the same time represent a possible threat to human health and local ecosystems.Abandoned Mine Lands (AML) are areas adjacent to or affected by abandoned mines. AML's often contain unmined mineral deposits, mine dumps (the ore and rock removed to get to the ore deposits), and tailings (the material left over from the ore processing) that contaminate the surrounding watershed and ecosystem. For example, streams near AML's can contain metals and (or) be so acidic that fish and aquatic insects cannot live in them.Many of these abandoned hard-rock mines are located on or adjacent to public lands administered by the Bureau of Land Management, National Park Service, and U.S. Forest Service. These federal land management agencies and the USGS are committed to mitigating the adverse effects that AML's can have on water quality and stream habitats.The USGS AML Initiative began in 1997 and will continue through 2001 in two pilot watersheds - the Boulder River basin in southwestern Montana and the upper Animas River basin in southwestern Colorado. The USGS is providing a wide range of scientific expertise to help land managers minimize and, where possible, eliminate the adverse environmental effects of AML's. USGS ecologists, geologists, water quality experts, hydrologists, geochemists, and mapping and digital data collection experts are collaborating to provide the scientific knowledge needed for an effective cleanup of AML's.

Komatiites and nickel sulfide ores of the Black Swan area, Yilgarn Craton, Western Australia. 4. Platinum group element distribution in the ores, and genetic implications

NASA Astrophysics Data System (ADS)

Barnes, Stephen J.

2004-11-01

The Black Swan komatiite sequence, in the Eastern Goldfields province of the Archaean Yilgarn Craton in Western Australia, is a body of dominantly olivine-rich cumulates with lesser volumes of spinifex textured rocks, interpreted as a section through an extensive komatiite lava flow field. The sequence hosts a number of nickel sulfide orebodies, including the Silver Swan massive shoot and the Cygnet and Black Swan disseminated orebodies. The massive sulfide orebodies of the Black Swan Succession are pervasively depleted in all platinum group elements (PGEs), particularly Pt and Pd, despite very high Ni contents. This depletion cannot be explained by R-factor variations, which would also require relatively low Ni tenors. The PGE depletion could be explained in part if the ores are enriched in a monosulfide solid solution (MSS) cumulate component, but requires some additional fractional segregation of sulfide melt upstream from the site of deposition. The Silver Swan orebody shows a remarkably consistent vertical zonation in PGE contents, particularly in Ir, Ru, Rh, Os, which increase systematically from very low levels at the stratigraphic base of the sulfide body to maxima corresponding roughly with the top of a lower layer of the orebody rich in silicate inclusions. Platinum shows the opposite trend, but is somewhat modified by remobilisation during talc carbonate alteration. A similar pattern is also observed in the adjacent White Swan orebody. This zonation is interpreted and modelled as the result of fractional crystallisation of MSS from the molten sulfide pool. The strong IPGE depletion towards the base of the orebody may be a consequence of sulfide liquid crystallisation in an inverted thermal gradient, between a thin rapidly cooling upper rind of komatiite lava and a hot substrate.

Enrichment of Sc2O3 and TiO2 from bauxite ore residues.

PubMed

Deng, Bona; Li, Guanghui; Luo, Jun; Ye, Qing; Liu, Mingxia; Peng, Zhiwei; Jiang, Tao

2017-06-05

As a major byproduct generated in the alumina industry, bauxite ore residue is an important reserve of scandium and titanium. In this study, the feasibility and mechanism of enriching Sc 2 O 3 and TiO 2 from a non-magnetic material, which was obtained from carbothermal reductive roasting and magnetic separation of bauxite ore residue, were investigated based on a two-step (acidic and alkali) leaching process. It was revealed that approximately 78% SiO 2 and 30-40% of CaO, FeO and Al 2 O 3 were removed from a non-magnetic material with 0.0134wt.% Sc 2 O 3 and 7.64wt.% TiO 2 by phosphoric acidic leaching, while about 95% Al 2 O 3 and P 2 O 5 were further leached by subsequent sodium hydroxide leaching of the upper-stream leach residue. A Sc 2 O 3 -, TiO 2 - rich material containing 0.044wt.% Sc 2 O 3 and 25.5wt.% TiO 2 was obtained, the recovery and the enrichment factor of Sc 2 O 3 and TiO 2 were about 85% and 5, respectively. The enrichment of Sc 2 O 3 was attributed to higher pH (>3.3) of phosphoric acid solution than its dissolution pH 0 , and the enrichment of TiO 2 was mainly associated with the insoluble perovskite (CaTiO 3 ) in the acidic solution at ambient temperature. As Sc 2 O 3 and TiO 2 cannot be dissolved in the alkali solution, they were further enriched in the leach residue. Copyright © 2017 Elsevier B.V. All rights reserved.

Bioavailability and uptake of smelter emissions in freshwater zooplankton in northeastern Washington, USA lakes using Pb isotope analysis and trace metal concentrations.

PubMed

Child, A W; Moore, B C; Vervoort, J D; Beutel, M W

2018-07-01

The upper Columbia River and associated valley systems are highly contaminated with metal wastes from nearby smelting operations in Trail, British Columbia, Canada (Teck smelter), and to a lesser extent, Northport, Washington, USA (Le Roi smelter). Previous studies have investigated depositional patterns of airborne emissions from these smelters, and documented the Teck smelter as the primary metal contamination source. However, there is limited research directed at whether these contaminants are bioavailable to aquatic organisms. This study investigates whether smelter derived contaminants are bioavailable to freshwater zooplankton. Trace metal (Zn, Cd, As, Sb, Pb and Hg) concentrations and Pb isotope compositions of zooplankton and sediment were measured in lakes ranging from 17 to 144 km downwind of the Teck smelter. Pb isotopic compositions of historic ores used by both smelters are uniquely less radiogenic than local geologic formations, so when zooplankton assimilate substantial amounts of smelter derived metals their compositions deviate from local baseline compositions toward ore compositions. Sediment metal concentrations and Pb isotope compositions in sediment follow significant (p < 0.001) negative exponential and sigmoidal patterns, respectively, as distance from the Teck smelting operation increases. Zooplankton As, Cd, and Sb contents were related to distance from the Teck smelter (p < 0.05), and zooplankton Pb isotope compositions suggest As, Cd, Sb and Pb from historic and current smelter emissions are biologically available to zooplankton. Zooplankton from lakes within 86 km of the Teck facility display isotopic evidence that legacy ore pollution is biologically available for assimilation. However, without water column data our study is unable to determine if legacy contaminants are remobilized from lake sediments, or erosional pathways from the watershed. Copyright © 2018 Elsevier Ltd. All rights reserved.

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

Ionization-potential depression and other dense plasma statistical property studies - Application to spectroscopic diagnostics.

NASA Astrophysics Data System (ADS)

Calisti, Annette; Ferri, Sandrine; Mossé, Caroline; Talin, Bernard

2017-02-01

The radiative properties of an emitter surrounded by a plasma, are modified through various mechanisms. For instance the line shapes emitted by bound-bound transitions are broadened and carry useful information for plasma diagnostics. Depending on plasma conditions the electrons occupying the upper quantum levels of radiators no longer exist as they belong to the plasma free electron population. All the charges present in the radiator environment contribute to the lowering of the energy required to free an electron in the fundamental state. This mechanism is known as ionization potential depression (IPD). The knowledge of IPD is useful as it affects both the radiative properties of the various ionic states and their populations. Its evaluation deals with highly complex n-body coupled systems, involving particles with different dynamics and attractive ion-electron forces. A classical molecular dynamics (MD) code, the BinGo-TCP code, has been recently developed to simulate neutral multi-component (various charge state ions and electrons) plasma accounting for all the charge correlations. In the present work, results on IPD and other dense plasma statistical properties obtained using the BinGo-TCP code are presented. The study focuses on aluminum plasmas for different densities and several temperatures in order to explore different plasma coupling conditions.

Krasnotur'insk Skarn copper ore field, Northern Urals: The U-Pb age of ore-controlling diorites and their place in the regional metallogeny

NASA Astrophysics Data System (ADS)

Grabezhev, A. I.; Ronkin, Yu. L.; Puchkov, V. N.; Gerdes, A.; Rovnushkin, M. Yu.

2014-06-01

The Krasnotur'insk skarn copper ore field known from the theoretical works of Academician K.S. Korzhinskii is located in the western part of the Tagil volcanic zone (in the area of the town of Krasnotur'insk). The ore field is composed of layered Devonian (Emsian) volcanosedimentary rocks intruded by small plutons of quartz diorites, diorites, and gabbrodiorites. Widespread pre-ore and intra-ore dikes of similar composition control the abundance of the andradite skarns formed after limestones and the magnetitesulfide and sulfide ore bodies formed after skarns. The LA-ICP-MS U-Pb concordant age of zircon from the quartz diorite of the Vasil'evsko-Moskalevskii pluton calculated by 16 analyses (16 crystals) is 407.7 ± 1.6 Ma (MSWD = 1.5). Taking into account the geological and petrogeochemical similarity of diorites of small plutons and intra-ore dikes, it is assumed that this age corresponds to the period of formation of the ore-magmatic system of the Krasnotur'insk skarn copper ore field. It was probably formed somewhat earlier than the Auerbakh montzonitic pluton and the accompanying skarn magnetite deposits in the south.

14 CFR 125.183 - Carriage of cargo in passenger compartments.

Code of Federal Regulations, 2011 CFR

2011-01-01

... emergency landing conditions applicable to the passenger seats of the airplane in which the bin is installed... bin. (3) The bin may not impose any load on the floor or other structure of the airplane that exceeds the load limitations of that structure. (4) The bin must be attached to the seat tracks or to the...

Chemical Equilibrium of the Dissolved Uranium in Groundwaters From a Spanish Uranium-Ore Deposit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garralon, Antonio; Gomez, Paloma; Turrero, Maria Jesus

2007-07-01

The main objectives of this work are to determine the hydrogeochemical evolution of an uranium ore and identify the main water/rock interaction processes that control the dissolved uranium content. The Mina Fe uranium-ore deposit is the most important and biggest mine worked in Spain. Sageras area is located at the north part of the Mina Fe, over the same ore deposit. The uranium deposit was not mined in Sageras and was only perturbed by the exploration activities performed 20 years ago. The studied area is located 10 Km northeast of Ciudad Rodrigo (Salamanca) at an altitude over 650 m.a.s.l. Themore » uranium mineralization is related to faults affecting the metasediments of the Upper Proterozoic to Lower Cambrian schist-graywacke complex (CEG), located in the Centro-Iberian Zone of the Hesperian Massif . The primary uranium minerals are uraninite and coffinite but numerous secondary uranium minerals have been formed as a result of the weathering processes: yellow gummite, autunite, meta-autunite, torbernite, saleeite, uranotile, ianthinite and uranopilite. The water flow at regional scale is controlled by the topography. Recharge takes place mainly in the surrounding mountains (Sierra Pena de Francia) and discharge at fluvial courses, mainly Agueda and Yeltes rivers, boundaries S-NW and NE of the area, respectively. Deep flows (lower than 100 m depth) should be upwards due to the river vicinity, with flow directions towards the W, NW or N. In Sageras-Mina Fe there are more than 100 boreholes drilled to investigate the mineral resources of the deposit. 35 boreholes were selected in order to analyze the chemical composition of groundwaters based on their depth and situation around the uranium ore. Groundwater samples come from 50 to 150 m depth. The waters are classified as calcium-bicarbonate type waters, with a redox potential that indicates they are slightly reduced (values vary between 50 to -350 mV). The TOC varies between <0.1 and 4.0 mgC/L and the dissolved uranium has a maximum value of 7.7 mg/L. According the analytical data of dissolved uranium, the mineral closest to equilibrium seems to be UO{sub 2}(am). The tritium contents in the groundwaters vary between 1.5 and 7.3 T.U. Considering that the mean value of tritium in rainwater from the studied area has a value of 4 T.U., it can be concluded that the residence times of the groundwaters are relatively short, not longer than 50 years in the oldest case. (authors)« less

13. ORE DOCK, LOOKING EAST FROM HULETT NO. 1. WHEN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. ORE DOCK, LOOKING EAST FROM HULETT NO. 1. WHEN BUILT IN 1911-1912, THIS WAS THE LARGEST ORE-UNLOADING DOCK ON THE GREAT LAKES. THE DOCK FEATURED FOUR HULETT UNLOADERS, EACH WITH A BUCKET CAPACITY OF 17 TONS; A 15-TON CAPACITY ORE STOCKING AND REHANDLING BRIDGE; AND A ONE-MILLION-TON CAPACITY ORE STORAGE YARD. THE WILLIAM-SEAVER-MORGAN COMPANY OF CLEVELAND BUILT THE DOCK EQUIPMENT. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Summary of the mineralogy of the Colorado Plateau uranium ores

USGS Publications Warehouse

Weeks, Alice D.; Coleman, Robert Griffin; Thompson, Mary E.

1956-01-01

In the Colorado Plateau uranium has been produced chiefly from very shallow mines in carnotite ores (oxidized vanadiferous uranium ores) until recent deeper mining penetrated black unoxidized ores in water-saturated rocks and extensive exploration has discovered many deposits of low to nonvanadiferous ores. The uranium ores include a wide range from highly vanadiferous and from as much as one percent to a trace of copper, and contain a small amount of iron and traces of lead, zinc, molybdenum, cobalt, nickel, silver, manganese, and other metals. Recent investigation indicates that the carnotite ores have been derived by progressive oxidation of primary (unoxidized) black ores that contain low-valent uranium and vanadium oxides and silicates. The uranium minerals, uraninite and coffinite, are associated with coalified wood or other carbonaceous material. The vanadium minerals, chiefly montroseite, roscoelite, and other vanadium silicates, occur in the interstices of the sandstone and in siltstone and clay pellets as well as associated with fossil wood. Calcite, dolomite, barite and minor amounts of sulfides, arsenides, and selenides occur in the unoxidized ore. Partially oxidized vanadiferous ore is blue black, purplish brown, or greenish black in contrast to the black or dark gray unoxidized ore. Vanadium combines with uranium to form rauvite. The excess vanadium is present in corvusite, fernandinite, melanovanadite and many other quadrivalent and quinquevalent vanadium minerals as well as in vanadium silicates. Pyrite and part or all of the calcite are replaced by iron oxides and gypsum. In oxidized vanadiferous uranium ores the uranium is fixed in the relatively insoluble minerals carnotite and tyuyamunite, and the excess vanadium commonly combines with one or more of the following: calcium, sodium, potassium, magnesium, aluminum, iron, copper, manganese, or barium, or rarely it forms the hydrated pentoxide. The relatively stable vanadium silicates are little affected by oxidation. The unoxidized nonvanadiferous ores contain uraninite and coffinite in close association with coalified wood and iron and copper sulfides, and traces of many other sulfides, arsenides and selenides. The oxidized nonvanadiferous ores differ from the vanadiferous ores because, in the absence of vanadium to complex the uranium, a great variety of secondary yellow and greenish-yellow uranyl minerals are formed. The uranyl sulfates and carbonates are more common than the oxides, phosphates, arsenates, and silicates. Because the sulfates and carbonates are much less stable that carnotite, the oxidized nonvanadiferous ores occure only as halos around cores of unoxidized ore and do not form large oxidized deposits close to the surface of the ground as carnotite ores. Oxidation has taken place since the lowering of the water table in the present erosion cycle. Because of local structures and the highly lenticular character of the fluviatile host rocks perched water tables and water-saturated lenses of sandstone are common high above the regional water table. Unoxidized ore has been preserved in these water-saturated rocks and the boundary between oxidized and unoxidized ore is very irregular.

Chromite Ore from the Transvaal Region of South Africa

EPA Pesticide Factsheets

In 2001, EPA finalized a rule to to delete both chromite ore mined in the Transvaal Region of South Africa and the unreacted ore component of the chromite ore processing residue (COPR) from TRI reporting requirements.

26. NORTHERN VIEW OF ORE YARD WITH ORE BRIDGES IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. NORTHERN VIEW OF ORE YARD WITH ORE BRIDGES IN THE BACKGROUND. BLAST FURNACES ALONG THE RIGHT SIDE. (Martin Stupich) - U.S. Steel Duquesne Works, Blast Furnace Plant, Along Monongahela River, Duquesne, Allegheny County, PA

A unique ore-placer area of the Amur region with high-Hg gold

NASA Astrophysics Data System (ADS)

Melnikov, A. V.; Stepanov, V. A.; Moiseenko, V. G.

2017-10-01

This work presents the geological structure and a description of the gold-ore occurrences and gold placers of the Un'ya-Bom ore-placer cluster of the Amur gold-bearing province. The host rocks are Late Paleozoic and Mesozoic black shales. Intrusive formations occur rarely. The sublatitudinal Un'ya Thrust is the principal ore-controlling structure. Paleozoic sandstones are thrust over Mesozoic flysch deposits along the Un'ya Thrust. The gold-ore occurrences are represented by quartz-vein zones. The ores are gold-quartz, low-sulfide. Ore minerals are arsenopyrite, scheelite, ferberite, galena, and native gold. High-Hg native gold was revealed in the ore occurrences and placers. The high Hg content in native gold is explained by the presence of the frontal part of the gold-bearing column located within the cluster; the rich placers were formed due to crushing of this column.

Virtual phosphorus ore requirement of Japanese economy.

PubMed

Matsubae, Kazuyo; Kajiyama, Jun; Hiraki, Takehito; Nagasaka, Tetsuya

2011-08-01

Phosphorus is indispensable for agricultural production. Hence, the consumption of imported food indirectly implies the import of phosphorus resources. The global consumption of agricultural products depends on a small number of ore-producing countries. For sustainable management of phosphorus resources, the global supply and demand network should be clarified. In this study, we propose the virtual phosphorus ore requirement as a new indicator of the direct and indirect phosphorus requirements for our society. The virtual phosphorus ore requirement indicates the direct and indirect demands for phosphorus ore transformed into agricultural products and fertilizer. In this study, the virtual phosphorus ore requirement was evaluated for the Japanese economy in 2005. Importantly, the results show that our society requires twice as much phosphorus ore as the domestic demand for fertilizer production. The phosphorus contained in "eaten" agricultural products was only 12% of virtual phosphorus ore requirement. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prevalence and Risk Factors of Elevated Blood Lead in Children in Gold Ore Processing Communities, Zamfara, Nigeria, 2012.

PubMed

Kaufman, John A; Brown, Mary Jean; Umar-Tsafe, Nasir T; Adbullahi, Muhammad Bashir; Getso, Kabiru I; Kaita, Ibrahim M; Sule, Binta Bako; Ba'aba, Ahmed; Davis, Lora; Nguku, Patrick M; Sani-Gwarzo, Nasir

2016-09-01

In March 2010, Medecins Sans Frontieres/Doctors Without Borders detected an outbreak of acute lead poisoning in Zamfara State, northwestern Nigeria, linked to low-technology gold ore processing. The outbreak killed more than 400 children ≤5 years of age in the first half of 2010 and has left more than 2,000 children with permanent disabilities. The aims of this study were to estimate the statewide prevalence of children ≤5 years old with elevated blood lead levels (BLLs) in gold ore processing and non-ore-processing communities, and to identify factors associated with elevated blood lead levels in children. A representative, population-based study of ore processing and non-ore-processing villages was conducted throughout Zamfara in 2012. Blood samples from children, outdoor soil samples, indoor dust samples, and survey data on ore processing activities and other lead sources were collected from 383 children ≤5 years old in 383 family compounds across 56 villages. 17.2% of compounds reported that at least one member had processed ore in the preceding 12 months (95% confidence intervals (CI): 9.7, 24.7). The prevalence of BLLs ≥10 µg/dL in children ≤5 years old was 38.2% (95% CI: 26.5, 51.4) in compounds with members who processed ore and 22.3% (95% CI: 17.8, 27.7) in compounds where no one processed ore. Ore processing activities were associated with higher lead concentrations in soil, dust, and blood samples. Other factors associated with elevated BLL were a child's age and sex, breastfeeding, drinking water from a piped tap, and exposure to eye cosmetics. Childhood lead poisoning is widespread in Zamfara State in both ore processing and non-ore-processing settings, although it is more prevalent in ore processing areas. Although most children's BLLs were below the recommended level for chelation therapy, environmental remediation and use of safer ore processing practices are needed to prevent further exposures. Obtained. The study protocol was approved by the US Centers for Disease Control Institutional Review Board-A and the National Health Research Ethics Committee of Nigeria. The authors declare no competing financial interests.

BinSanity: unsupervised clustering of environmental microbial assemblies using coverage and affinity propagation

PubMed Central

Heidelberg, John F.; Tully, Benjamin J.

2017-01-01

Metagenomics has become an integral part of defining microbial diversity in various environments. Many ecosystems have characteristically low biomass and few cultured representatives. Linking potential metabolisms to phylogeny in environmental microorganisms is important for interpreting microbial community functions and the impacts these communities have on geochemical cycles. However, with metagenomic studies there is the computational hurdle of ‘binning’ contigs into phylogenetically related units or putative genomes. Binning methods have been implemented with varying approaches such as k-means clustering, Gaussian mixture models, hierarchical clustering, neural networks, and two-way clustering; however, many of these suffer from biases against low coverage/abundance organisms and closely related taxa/strains. We are introducing a new binning method, BinSanity, that utilizes the clustering algorithm affinity propagation (AP), to cluster assemblies using coverage with compositional based refinement (tetranucleotide frequency and percent GC content) to optimize bins containing multiple source organisms. This separation of composition and coverage based clustering reduces bias for closely related taxa. BinSanity was developed and tested on artificial metagenomes varying in size and complexity. Results indicate that BinSanity has a higher precision, recall, and Adjusted Rand Index compared to five commonly implemented methods. When tested on a previously published environmental metagenome, BinSanity generated high completion and low redundancy bins corresponding with the published metagenome-assembled genomes. PMID:28289564

Loss of Bin1 Promotes the Propagation of Tau Pathology.

PubMed

Calafate, Sara; Flavin, William; Verstreken, Patrik; Moechars, Diederik

2016-10-18

Tau pathology propagates within synaptically connected neuronal circuits, but the underlying mechanisms are unclear. BIN1-amphiphysin2 is the second most prevalent genetic risk factor for late-onset Alzheimer's disease. In diseased brains, the BIN1-amphiphysin2 neuronal isoform is downregulated. Here, we show that lowering BIN1-amphiphysin2 levels in neurons promotes Tau pathology propagation whereas overexpression of neuronal BIN1-amphiphysin2 inhibits the process in two in vitro models. Increased Tau propagation is caused by increased endocytosis, given our finding that BIN1-amphiphysin2 negatively regulates endocytic flux. Furthermore, blocking endocytosis by inhibiting dynamin also reduces Tau pathology propagation. Using a galectin-3-binding assay, we show that internalized Tau aggregates damage the endosomal membrane, allowing internalized aggregates to leak into the cytoplasm to propagate pathology. Our work indicates that lower BIN1 levels promote the propagation of Tau pathology by efficiently increasing aggregate internalization by endocytosis and endosomal trafficking. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Mosquito larvicide BinAB revealed by de novo phasing with an X-ray laser

PubMed Central

Colletier, Jacques-Philippe; Sawaya, Michael R.; Gingery, Mari; Rodriguez, Jose A.; Cascio, Duilio; Brewster, Aaron S.; Michels-Clark, Tara; Hice, Robert H.; Coquelle, Nicolas; Boutet, Sébastien; Williams, Garth J.; Messerschmidt, Marc; DePonte, Daniel P.; Sierra, Raymond G.; Laksmono, Hartawan; Koglin, Jason E.; Hunter, Mark S.; Park, Hyun-Woo; Uervirojnangkoorn, Monarin; Bideshi, Dennis K.; Brunger, Axel T.; Federici, Brian A.; Sauter, Nicholas K.; Eisenberg, David S.

2016-01-01

Summary BinAB is a naturally occurring paracrystalline larvicide distributed worldwide to combat the devastating diseases borne by mosquitoes. These crystals are composed of homologous molecules, BinA and BinB, which play distinct roles in the multi-step intoxication process, transforming from harmless, robust crystals, to soluble protoxin heterodimers, to internalized mature toxin, and finally toxic oligomeric pores. The small size of the crystals, 50 unit cells per edge, on average, has impeded structural characterization by conventional means. Here, we report the structure of BinAB solved de novo by serial-femtosecond crystallography at an X-ray free-electron laser (XFEL). The structure reveals tyrosine and carboxylate-mediated contacts acting as pH switches to release soluble protoxin in the alkaline larval midgut. An enormous heterodimeric interface appears responsible for anchoring BinA to receptor-bound BinB for co-internalization. Remarkably, this interface is largely composed of propeptides, suggesting that proteolytic maturation would trigger dissociation of the heterodimer and progression to pore formation. PMID:27680699

On the Mathematical Consequences of Binning Spike Trains.

PubMed

Cessac, Bruno; Le Ny, Arnaud; Löcherbach, Eva

2017-01-01

We initiate a mathematical analysis of hidden effects induced by binning spike trains of neurons. Assuming that the original spike train has been generated by a discrete Markov process, we show that binning generates a stochastic process that is no longer Markov but is instead a variable-length Markov chain (VLMC) with unbounded memory. We also show that the law of the binned raster is a Gibbs measure in the DLR (Dobrushin-Lanford-Ruelle) sense coined in mathematical statistical mechanics. This allows the derivation of several important consequences on statistical properties of binned spike trains. In particular, we introduce the DLR framework as a natural setting to mathematically formalize anticipation, that is, to tell "how good" our nervous system is at making predictions. In a probabilistic sense, this corresponds to condition a process by its future, and we discuss how binning may affect our conclusions on this ability. We finally comment on the possible consequences of binning in the detection of spurious phase transitions or in the detection of incorrect evidence of criticality.

Lead isotope studies of the Guerrero composite terrane, west-central Mexico: implications for ore genesis

NASA Astrophysics Data System (ADS)

Potra, Adriana; Macfarlane, Andrew W.

2014-01-01

New thermal ionization mass spectrometry and multi-collector inductively coupled plasma mass spectrometry Pb isotope analyses of three Cenozoic ores from the La Verde porphyry copper deposit located in the Zihuatanejo-Huetamo subterrane of the Guerrero composite terrane are presented and the metal sources are evaluated. Lead isotope ratios of 3 Cenozoic ores from the El Malacate and La Esmeralda porphyry copper deposits located in the Zihuatanejo-Huetamo subterrane and of 14 ores from the Zimapan and La Negra skarn deposits from the adjoining Sierra Madre terrane are also presented to look for systematic differences in the lead isotope trends and ore metal sources among the proposed exotic tectonostratigraphic terranes of southern Mexico. Comparison among the isotopic signatures of ores from the Sierra Madre terrane and distinct subterranes of the Guerrero terrane supports the idea that there is no direct correlation between the distinct suspect terranes of Mexico and the isotopic signatures of the associated Cenozoic ores. Rather, these Pb isotope patterns are interpreted to reflect increasing crustal contribution to mantle-derived magmas as the arc advanced eastward onto a progressively thicker continental crust. The lead isotope trend observed in Cenozoic ores is not recognized in the ores from Mesozoic volcanogenic massive sulfide and sedimentary exhalative deposits. The Mesozoic ores formed prior to the amalgamation of the Guerrero composite terrane to the continental margin, which took place during the Late Cretaceous, in intraoceanic island arc and intracontinental marginal basin settings, while the Tertiary deposits formed after this event in a continental arc setting. Lead isotope ratios of the Mesozoic and Cenozoic ores appear to reflect these differences in tectonic setting of ore formation. Most Pb isotope values of ores from the La Verde deposit (206Pb/204Pb = 18.674-18.719) are less radiogenic than those of the host igneous rocks, but plot within the field defined by the Huetamo Sequence, suggesting that these ores may also contain metals from the sedimentary rocks. The Pb isotope ratios of ore samples from the Zimapan deposit (206Pb/204Pb = 18.771-18.848) are substantially higher than the whole-rock Pb isotope compositions of the basement rocks. The similarity of ore Pb to igneous rock Pb in the Zimapan district (206Pb/204Pb = 18.800-18.968) may indicate that the proximal source of ore metals in the hydrothermal system was the igneous activity.

Face format at encoding affects the other-race effect in face memory.

PubMed

Zhao, Mintao; Hayward, William G; Bülthoff, Isabelle

2014-08-07

Memory of own-race faces is generally better than memory of other-races faces. This other-race effect (ORE) in face memory has been attributed to differences in contact, holistic processing, and motivation to individuate faces. Since most studies demonstrate the ORE with participants learning and recognizing static, single-view faces, it remains unclear whether the ORE can be generalized to different face learning conditions. Using an old/new recognition task, we tested whether face format at encoding modulates the ORE. The results showed a significant ORE when participants learned static, single-view faces (Experiment 1). In contrast, the ORE disappeared when participants learned rigidly moving faces (Experiment 2). Moreover, learning faces displayed from four discrete views produced the same results as learning rigidly moving faces (Experiment 3). Contact with other-race faces was correlated with the magnitude of the ORE. Nonetheless, the absence of the ORE in Experiments 2 and 3 cannot be readily explained by either more frequent contact with other-race faces or stronger motivation to individuate them. These results demonstrate that the ORE is sensitive to face format at encoding, supporting the hypothesis that relative involvement of holistic and featural processing at encoding mediates the ORE observed in face memory. © 2014 ARVO.

FY2017 status report: Model 9975 O-ring fixture long-term leak performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W. L.

A series of experiments to monitor the aging performance of Viton® GLT and GLT-S O-rings used in the Model 9975 shipping package has been ongoing since 2004 at the Savannah River National Laboratory. One approach has been to periodically evaluate the leak performance of O-rings being aged in mock-up 9975 Primary Containment Vessels (PCVs) at elevated temperature. Other methods such as compression-stress relaxation (CSR) tests and field surveillance are also on-going to evaluate O-ring behavior. Seventy tests using PCV mock-ups with GLT O-rings were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially andmore » have been tested periodically to determine if they continue to meet the leak-tightness criterion defined in ANSI standard N14.5-97. Due to material substitution, a smaller test matrix with fourteen additional tests was initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. Leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The 300 °F GLT O-ring fixtures failed after 2.8 to 5.7 years at temperature. The remaining GLT O-ring fixtures aging at 300 ºF were retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 9 to 10.5 years, or in GLT O-ring fixtures aging at 270 ºF for 5.7 years. These aging temperatures bound O-ring temperatures anticipated during normal storage in K-Area Complex (KAC). Leak test failures have been experienced in all of the GLT-S O-ring fixtures aging at 300 ºF and above. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 and 250 ºF for 6.9 to 7.5 years. Data from the O-ring fixtures are generally consistent with results from compression stress relaxation testing, and provide confidence in the predictive models based on those results. However, uncertainty still exists in extrapolating these elevated temperature results to the lower temperatures of interest for normal storage in KAC. Measurement of compression set in O-rings removed from failed fixtures, compared to that from KAC surveillance O-rings, indicates margin remains for O-rings still in service. Aging and periodic leak testing will continue for the remaining PCV fixtures.« less

Occurrence of silver minerals in a silver-rich pocket in the massive sulfide zinc-lead ores in the Edwards mine, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serviss, C.R.; Grout, C.M.; Hagni, R.D.

1985-01-01

Ore microscopic examination of uncommon silver-rich ores from the Edwards mine has detected three silver minerals, native silver, freibergite, and argentite, that were previously unreported in the literature from the Balmat-Edwards district. The zinc-lead ore deposits of the Balmat-Edwards District in northern New York are composed of very coarse-grained massive sulfides, principally sphalerite, galena, and pyrite. The typical ores contain small amounts of silver in solid solution galena. Galena concentrates produced from those ores have contained an average of 15 ounces of silver per ton of 60% lead concentrates. In contrast to the typical ore a silver-rich pocket, that measuredmore » three feet by three feet on the vertical mine face and was the subject of this study, contained nearly 1% silver in a zinc ore. Ore microscopic study shows that this ore is especially characterized by abundant, relatively fine-grained chalcopyrite with anhedral pyrite inclusions. Fine-grained sphalerite, native silver, argentite, freibergite and arsenopyrite occur in association with the chalcopyrite and as fracture-fillings in gangue minerals. Geochemically anomalous amounts of tin, barium, chromium, and nickel also are present in the silver-rich pocket. The silver-rich pocket may mark the locus of an early feeder vent or alternatively it may record a hydrothermal event that was superimposed upon the event responsible for the metamorphic ore textures.« less

SU-F-T-253: Volumetric Comparison Between 4D CT Amplitude and Phase Binning Mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, G; Ma, R; Reyngold, M

2016-06-15

Purpose: Motion artifact in 4DCT images can affect radiation treatment quality. To identify the most robust and accurate binning method, we compare the volume difference between targets delineated on amplitude and phase binned 4DCT scans. Methods: Varian RPM system and CT scanner were used to acquire 4DCTs of a Quasar phantom with embedded cubic and spherical objects having superior-inferior motion. Eight patients’ respiration waveforms were used to drive the phantom. The 4DCT scan was reconstructed into 10 phase and 10 amplitude bins (2 mm slices). A scan of the static phantom was also acquired. For each waveform, sphere and cubemore » volumes were generated automatically on each phase using HU thresholding. Phase (amplitude) ITVs were the union of object volumes over all phase (amplitude) binned images. The sphere and cube volumes measured in the static phantom scan were V{sub sphere}=4.19cc and V{sub cube}=27.0cc. Volume difference (VD) and dice similarity coefficient (DSC) of the ITVs, and mean volume error (MVE) defined as the average target volume percentage difference between each phase image and the static image, were used to evaluate the performance of amplitude and phase binning. Results: Averaged over the eight breathing traces, the VD and DSC of the internal target volume (ITV) between amplitude and phase binning were 3.4%±3.2% (mean ± std) and 95.9%±2.1% for sphere; 2.1%±3.3% and 98.0% ±1.5% for cube, respectively.For all waveforms, the average sphere MVE of amplitude and phase binning was 6.5% ± 5.0% and 8.2%±6.3%, respectively; and the average cube MVE of amplitude and phase binning was 5.7%±3.5%and 12.9%±8.9%, respectively. Conclusion: ITV volume and spatial overlap as assessed by VD and DSC are similar between amplitude and phase binning. Compared to phase binning, amplitude binning results in lower MVE suggesting it is less susceptible to motion artifact.« less

29. ORE DOCK, LOOKING WEST; AT WORK UNLOADING THE 'GEORGE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. ORE DOCK, LOOKING WEST; AT WORK UNLOADING THE 'GEORGE M. HUMPHREY'S' CARGO OF 25,000. TONS OF ORE. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Surface contamination of hazardous drug pharmacy storage bins and pharmacy distributor shipping containers.

PubMed

Redic, Kimberly A; Fang, Kayleen; Christen, Catherine; Chaffee, Bruce W

2018-03-01

Purpose This study was conducted to determine whether there is contamination on exterior drug packaging using shipping totes from the distributor and carousel storage bins as surrogate markers of external packaging contamination. Methods A two-part study was conducted to measure the presence of 5-fluorouracil, ifosfamide, cyclophosphamide, docetaxel and paclitaxel using surrogate markers for external drug packaging. In Part I, 10 drug distributor shipping totes designated for transport of hazardous drugs provided a snapshot view of contamination from regular use and transit in and out of the pharmacy. An additional two totes designated for transport of non-hazardous drugs served as controls. In Part II, old carousel storage bins (i.e. those in use pre-study) were wiped for snapshot view of hazardous drug contamination on storage bins. New carousel storage bins were then put into use for storage of the five tested drugs and used for routine storage and inventory maintenance activities. Carousel bins were wiped at time intervals 0, 8, 16 and 52 weeks to measure surface contamination. Results Two of the 10 hazardous shipping totes were contaminated. Three of the five-old carousel bins were contaminated with cyclophosphamide. One of the old carousel bins was also contaminated with ifosfamide. There were no detectable levels of hazardous drugs on any of the new storage bins at time 0, 8 or 16 weeks. However, at the Week 52, there was a detectable level of 5-FU present in the 5-FU carousel bin. Conclusions Contamination of the surrogate markers suggests that external packaging for hazardous drugs is contaminated, either during the manufacturing process or during routine chain of custody activities. These results demonstrate that occupational exposure may occur due to contamination from shipping totes and storage bins, and that handling practices including use of personal protective equipment is warranted.

Application of indigenous sulfur-oxidizing bacteria from municipal wastewater to selectively bioleach phosphorus from high-phosphorus iron ore: effect of particle size.

PubMed

Shen, Shaobo; Rao, Ruirui; Wang, Jincao

2013-01-01

The effects of ore particle size on selectively bioleaching phosphorus (P) from high-phosphorus iron ore were studied. The average contents of P and Fe in the iron ore were 1.06 and 47.90% (w/w), respectively. The particle sizes of the ores used ranged from 58 to 3350 microm. It was found that the indigenous sulfur-oxidizing bacteria from municipal wastewater could grow well in the slurries of solid high-phosphorus iron ore and municipal wastewater. The minimum bioleaching pH reached for the current work was 0.33. The P content in bioleached iron ore reduced slightly with decreasing particle size, while the removal percentage of Fe decreased appreciably with decreasing particle size. The optimal particle size fraction was 58-75 microm, because the P content in bioleached iron ore reached a minimum of 0.16% (w/w), the removal percentage of P attained a maximum of 86.7%, while the removal percentage of Fe dropped to a minimum of 1.3% and the Fe content in bioleached iron ore was a maximum of 56.4% (w/w) in this case. The iron ores thus obtained were suitable to be used in the iron-making process. The removal percentage of ore solid decreased with decreasing particle size at particle size range of 106-3350 microm. The possible reasons resulting in above phenomena were explored in the current work. It was inferred that the particle sizes of the iron ore used in this work have no significant effect on the viability of the sulfur-oxidizing bacteria.

Sedimentary exhalative nickel-molybdenum ores in south China

USGS Publications Warehouse

Lott, D.A.; Coveney, R.M.; Murowchick, J.B.; Grauch, R.I.

1999-01-01

Unique bedded Ni-Mo ores hosted by black shales were discovered in localized paleobasins along the Yangzte platform of southern China in 1971. Textural evidence and radiometric dates imply ore formation during sedimentation of black shales that grade into readily combustible beds, termed stone coals, which contain 10 to 15 percent organic carbon. Studies of 427 fluid inclusions indicate extreme variation in hydrothermal brine salinities that were contained by Proterozoic dolostones underlying the ore zone in Hunan and Guizhou. Variations of fluid inclusion salinities, which range from 0.1 to 21.6 wt percent NaCl equiv, are attributed to differences in the compositions of brines in strata underlying the ore bed, complicated by the presence of seawater and dilute fluids that represent condensates of vapors generated by boiling of mineralizing fluids or Cambrian meteoric water. The complex processes of ore deposition led to scattered homogenization temperatures ranging from 100??to 187??C within the Hunan ore zone and from 65??to 183??C within the Guizhou ore zone. While living organisms probably did not directly accumulate metals in situ in sufficient amounts to explain the unusually high grades of the deposits, sulfur isotope ratios indicate that bacteria, now preserved as abundant microfossils, provided sufficient sulfide for the ores by reduction of seawater sulfate. Such microbiota may have depended on vent fluids and transported organic matter for key nutrients and are consistent with a sedex origin for the ores. Vent fluids interacted with organic remains, including rounded fragments of microbial mats that were likely transported to the site of ore deposition by the action of waves and bottom currents prior to replacement by ore minerals.

Multi-Criteria selection of technology for processing ore raw materials

NASA Astrophysics Data System (ADS)

Gorbatova, E. A.; Emelianenko, E. A.; Zaretckii, M. V.

2017-10-01

The development of Computer-Aided Process Planning (CAPP) for the Ore Beneficiation process is considered. The set of parameters to define the quality of the Ore Beneficiation process is identified. The ontological model of CAPP for the Ore Beneficiation process is described. The hybrid choice method of the most appropriate variant of the Ore Beneficiation process based on the Logical Conclusion Rules and the Fuzzy Multi-Criteria Decision Making (MCDM) approach is proposed.

Process for recovering hydrocarbons from a diatomite-type ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.W.

1983-02-15

A process for recovering hydrocarbons from a diatomite-type ore which comprises contacting the diatomite ore with a C/sub 4/-C/sub 10/ alcohol and thereafter contacting the diatomite ore-alcohol mixture with an aqueous alkaline solution to separate a hydrocarbon-alcohol phase and an alkaline aqueous phase containing the stripped diatomite ore. Thereafter, the alcohol is distilled off from the hydrocarbon phase and recycled back into the initial process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yaping; Williams, Brent J.; Goldstein, Allen H.

Here, we present a rapid method for apportioning the sources of atmospheric organic aerosol composition measured by gas chromatography–mass spectrometry methods. Here, we specifically apply this new analysis method to data acquired on a thermal desorption aerosol gas chromatograph (TAG) system. Gas chromatograms are divided by retention time into evenly spaced bins, within which the mass spectra are summed. A previous chromatogram binning method was introduced for the purpose of chromatogram structure deconvolution (e.g., major compound classes) (Zhang et al., 2014). Here we extend the method development for the specific purpose of determining aerosol samples' sources. Chromatogram bins are arrangedmore » into an input data matrix for positive matrix factorization (PMF), where the sample number is the row dimension and the mass-spectra-resolved eluting time intervals (bins) are the column dimension. Then two-dimensional PMF can effectively do three-dimensional factorization on the three-dimensional TAG mass spectra data. The retention time shift of the chromatogram is corrected by applying the median values of the different peaks' shifts. Bin width affects chemical resolution but does not affect PMF retrieval of the sources' time variations for low-factor solutions. A bin width smaller than the maximum retention shift among all samples requires retention time shift correction. A six-factor PMF comparison among aerosol mass spectrometry (AMS), TAG binning, and conventional TAG compound integration methods shows that the TAG binning method performs similarly to the integration method. However, the new binning method incorporates the entirety of the data set and requires significantly less pre-processing of the data than conventional single compound identification and integration. In addition, while a fraction of the most oxygenated aerosol does not elute through an underivatized TAG analysis, the TAG binning method does have the ability to achieve molecular level resolution on other bulk aerosol components commonly observed by the AMS.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Islam, Md. Shafiqul, E-mail: shafique@eng.ukm.my; Hannan, M.A., E-mail: hannan@eng.ukm.my; Basri, Hassan

Highlights: • Solid waste bin level detection using Dynamic Time Warping (DTW). • Gabor wavelet filter is used to extract the solid waste image features. • Multi-Layer Perceptron classifier network is used for bin image classification. • The classification performance evaluated by ROC curve analysis. - Abstract: The increasing requirement for Solid Waste Management (SWM) has become a significant challenge for municipal authorities. A number of integrated systems and methods have introduced to overcome this challenge. Many researchers have aimed to develop an ideal SWM system, including approaches involving software-based routing, Geographic Information Systems (GIS), Radio-frequency Identification (RFID), or sensormore » intelligent bins. Image processing solutions for the Solid Waste (SW) collection have also been developed; however, during capturing the bin image, it is challenging to position the camera for getting a bin area centralized image. As yet, there is no ideal system which can correctly estimate the amount of SW. This paper briefly discusses an efficient image processing solution to overcome these problems. Dynamic Time Warping (DTW) was used for detecting and cropping the bin area and Gabor wavelet (GW) was introduced for feature extraction of the waste bin image. Image features were used to train the classifier. A Multi-Layer Perceptron (MLP) classifier was used to classify the waste bin level and estimate the amount of waste inside the bin. The area under the Receiver Operating Characteristic (ROC) curves was used to statistically evaluate classifier performance. The results of this developed system are comparable to previous image processing based system. The system demonstration using DTW with GW for feature extraction and an MLP classifier led to promising results with respect to the accuracy of waste level estimation (98.50%). The application can be used to optimize the routing of waste collection based on the estimated bin level.« less

The retrospective binning method improves the consistency of phase binning in respiratory-gated PET/CT

NASA Astrophysics Data System (ADS)

Didierlaurent, D.; Ribes, S.; Batatia, H.; Jaudet, C.; Dierickx, L. O.; Zerdoud, S.; Brillouet, S.; Caselles, O.; Courbon, F.

2012-12-01

This study assesses the accuracy of prospective phase-gated PET/CT data binning and presents a retrospective data binning method that improves image quality and consistency. Respiratory signals from 17 patients who underwent 4D PET/CT were analysed to evaluate the reproducibility of temporal triggers used for the standard phase-based gating method. Breathing signals were reprocessed to implement retrospective PET data binning. The mean and standard deviation of time lags between automatic triggers provided by the Real-time Position Management (RPM, Varian) gating device and inhalation peaks derived from respiratory curves were computed for each patient. The total number of respiratory cycles available for 4D PET/CT according to the binning mode (prospective versus retrospective) was compared. The maximum standardized uptake value (SUVmax), biological tumour volume (BTV) and tumour trajectory measures were determined from the PET/CT images of five patients. Compared to retrospective binning (RB), prospective gating approach led to (i) a significant loss in breathing cycles (15%) and (ii) the inconsistency of data binning due to temporal dispersion of triggers (average 396 ms). Consequently, tumour characterization could be impacted. In retrospective mode, SUVmax was up to 27% higher, where no significant difference appeared in BTV. In addition, prospective mode gave an inconsistent spatial location of the tumour throughout the bins. Improved consistency with breathing patterns and greater motion amplitude of the tumour centroid were observed with retrospective mode. The detection of the tumour motion and trajectory was improved also for small temporal dispersion of triggers. This study shows that the binning mode could have a significant impact on 4D PET images. The consistency of triggers with breathing signals should be checked before clinical use of gated PET/CT images, and our RB method improves 4D PET/CT image quantification.

Mesoscale variability of the Upper Colorado River snowpack

USGS Publications Warehouse

Ling, C.-H.; Josberger, E.G.; Thorndike, A.S.

1996-01-01

In the mountainous regions of the Upper Colorado River Basin, snow course observations give local measurements of snow water equivalent, which can be used to estimate regional averages of snow conditions. We develop a statistical technique to estimate the mesoscale average snow accumulation, using 8 years of snow course observations. For each of three major snow accumulation regions in the Upper Colorado River Basin - the Colorado Rocky Mountains, Colorado, the Uinta Mountains, Utah, and the Wind River Range, Wyoming - the snow course observations yield a correlation length scale of 38 km, 46 km, and 116 km respectively. This is the scale for which the snow course data at different sites are correlated with 70 per cent correlation. This correlation of snow accumulation over large distances allows for the estimation of the snow water equivalent on a mesoscale basis. With the snow course data binned into 1/4?? latitude by 1/4?? longitude pixels, an error analysis shows the following: for no snow course data in a given pixel, the uncertainty in the water equivalent estimate reaches 50 cm; that is, the climatological variability. However, as the number of snow courses in a pixel increases the uncertainty decreases, and approaches 5-10 cm when there are five snow courses in a pixel.

Inside the small-scale composting of kitchen and garden wastes: Thermal performance and stratification effect in vertical compost bins.

PubMed

Arrigoni, Juan Pablo; Paladino, Gabriela; Garibaldi, Lucas Alejandro; Laos, Francisca

2018-06-01

Decentralized composting has been proposed as a best available practice, with a highly positive impact on municipal solid wastes management plans. However, in cold climates, decentralized small-scale composting performance to reach thermophilic temperatures (required for the product sanitization) could be poor, due to a lack of critical mass to retain heat. In addition, in these systems the composting process is usually disturbed when new portions of fresh organic waste are combined with previous batches. This causes modifications in the well-known composting evolution pattern. The objective of this work was to improve the understanding of these technical aspects through a real-scale decentralized composting experience carried out under cold climate conditions, in order to assess sanitization performance and to study the effects of fresh feedstock additions in the process evolution. Kitchen and garden organic wastes were composted in 500 L-static compost bins (without turning) for 244 days under cold climate conditions (Bariloche, NW Patagonia, Argentina), using pine wood shavings in a ratio of 1.5:1 v: v (waste: bulking agent). Temperature profile, stability indicators (microbial activity, carbon and nitrogen contents and ratio) and other variables (pH and electrical conductivity), were monitored throughout the experience. Our results indicate that small-scale composting (average generation rate of 7 kg d -1 ) is viable under cold weather conditions, since thermophilic sanitization temperatures (> 55 °C) were maintained for 3 consecutive days in most of the composting mass, according to available USEPA regulations commonly used as a reference for pathogens control in sewage sludge. On the other hand, stability indicators showed a differentiated organic matter degradation process along the compost bins height. Particularly, in the bottommost composting mix layer the process took a longer period to achieve compost stability than the upper layers, suggesting that differential organic matter transformation appears not to be necessarily associated to the order of the waste batches incorporation in a time line, as it could be expected. These findings suggest the need to discuss new ways of studying the composting process in small-scale compost bins as well as their commercial design. Copyright © 2018 Elsevier Ltd. All rights reserved.

6. Looking west showing top of dock: steaming frozen ore ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Looking west showing top of dock: steaming frozen ore which had been put in pockets in December 1959, May 6, 1990. Photographer: unknown - Marquette Ore Dock No. 6, Ore Dock, On pilings in Marquette City Lower Harbor, Marquette, Marquette County, MI

Explosion-assisted preparation of dispersed gold-bearing different-grade ore for selective mining

NASA Astrophysics Data System (ADS)

Trubachev, AI; Zykov, NV

2017-02-01

It is found that there are transient zones (between quality and off-quality ore areas) with the respective content of useful component in an ore body, and a variant of explosive treatment of such zones before the selective mining is put forward. Practicability of two processing technologies is evaluated: processing of high-grade and low-grade ore from the transient zones and heap leaching of metals from the low-grade and impoverished ore. Open mining technology is conventional truck-and-shovel scheme, with distributed ore flows to processing plant and (or) to heap leaching, which generally enhances the mine efficiency.

Rational design of bottom blocks for development of ore deposits systems with caving of ore and enclosing rocks

NASA Astrophysics Data System (ADS)

Versilov, S. O.; Posylniy, Yu V.; Shurygin, D. N.; Tretyak, A. Ya

2017-10-01

The assessment of the geological conditions of development of existing ore deposits was made. For testing ore deposits in difficult mining and geological conditions, the authors proposed the system of development, accompanied by collapse of the mechanical ore with the use of feeders of active action that could be manufactured directly in the mine in accordance with the specific conditions of occurrence of minerals. The paper demonstrates the technology of manufacture of load-bearing structures of the feeder directly in the mine at the scene of the breaking of the first layer of ore, as well as the dynamics of the ore and the choice of parameters of concrete feeders. A new design of the bottom block was proposed, the idea of technical solution of which consists in the fact that it is offered to undergo the production of the smallest possible cross section, which is determined only by the dimensions of the conveyors to deliver ore. And before the explosion of fans of production wells, it is necessary to produce local collapse of the roof production to increase its height at the place of production of ore by blasting wellheads in two or three rows.

Prevalence and Risk Factors of Elevated Blood Lead in Children in Gold Ore Processing Communities, Zamfara, Nigeria, 2012

PubMed Central

Kaufman, John A.; Brown, Mary Jean; Umar-Tsafe, Nasir T.; Adbullahi, Muhammad Bashir; Getso, Kabiru I.; Kaita, Ibrahim M.; Sule, Binta Bako; Ba’aba, Ahmed; Davis, Lora; Nguku, Patrick M.; Sani-Gwarzo, Nasir

2018-01-01

Background In March 2010, Medecins Sans Frontieres/Doctors Without Borders detected an outbreak of acute lead poisoning in Zamfara State, northwestern Nigeria, linked to low-technology gold ore processing. The outbreak killed more than 400 children ≤5 years of age in the first half of 2010 and has left more than 2,000 children with permanent disabilities. Objectives The aims of this study were to estimate the statewide prevalence of children ≤5 years old with elevated blood lead levels (BLLs) in gold ore processing and non-ore-processing communities, and to identify factors associated with elevated blood lead levels in children. Methods A representative, population-based study of ore processing and non-ore-processing villages was conducted throughout Zamfara in 2012. Blood samples from children, outdoor soil samples, indoor dust samples, and survey data on ore processing activities and other lead sources were collected from 383 children ≤5 years old in 383 family compounds across 56 villages. Results 17.2% of compounds reported that at least one member had processed ore in the preceding 12 months (95% confidence intervals (CI): 9.7, 24.7). The prevalence of BLLs ≥10 µg/dL in children ≤5 years old was 38.2% (95% CI: 26.5, 51.4) in compounds with members who processed ore and 22.3% (95% CI: 17.8, 27.7) in compounds where no one processed ore. Ore processing activities were associated with higher lead concentrations in soil, dust, and blood samples. Other factors associated with elevated BLL were a child’s age and sex, breastfeeding, drinking water from a piped tap, and exposure to eye cosmetics. Conclusions Childhood lead poisoning is widespread in Zamfara State in both ore processing and non-ore-processing settings, although it is more prevalent in ore processing areas. Although most children’s BLLs were below the recommended level for chelation therapy, environmental remediation and use of safer ore processing practices are needed to prevent further exposures. Patient consent Obtained Ethics approval The study protocol was approved by the US Centers for Disease Control Institutional Review Board-A and the National Health Research Ethics Committee of Nigeria. Competing Interests The authors declare no competing financial interests. PMID:29416933

Geology and ore fluid geochemistry of the Jinduicheng porphyry molybdenum deposit, East Qinling, China

NASA Astrophysics Data System (ADS)

Li, Hongying; Ye, Huishou; Wang, Xiaoxia; Yang, Lei; Wang, Xiuyuan

2014-01-01

Jinduicheng deposit is a giant Mesozoic porphyry Mo system deposit in the East Qinling molybdenum belt, Shaanxi Province, China. The mineralization is associated with the I-type Jinduicheng granite porphyry. Both the porphyry stock and country rocks underwent intense hydrothermal alteration. The alteration, with increasing distance from the parent intrusion, changes from silicification, through potassic and phyllic assemblages, carbonation, to propylitic assemblages. Molybdenite, the dominant ore mineral, occurs in veinlets, most of which are hosted by the altered country rocks, with less than 25% of the ore in the porphyry body. The hydrothermal system comprises four stages, including pre-ore quartz and K-feldspar; two ore stages of quartz, K-feldspar, molybdenite, and Pb- And Zn-bearing sulfides; and post-ore quartz and carbonate. Six main types of primary fluid inclusions are present in hydrothermal quartz, including two-phase aqueous, one-phase aqueous, three-phase CO2-bearing, CO2-dominated fluid inclusions, gas inclusions, and melt inclusions. The homogenization temperatures of fluid inclusions range from 210 to 290 °C in the pre-ore stage, 150-310 °C in ore stage I, 150-360 °C in the ore stage II, and 195-325 °C in the post-ore stage quartz. Estimated salinities of the ore-forming fluids range from 6.9 to 13.5, 4.3 to 12.3, 6.2 to 12.4, and 3.4 to 9.9 wt.% NaCl equiv. in stages 1-4, respectively. The δ34S values of pyrite in the two ore stages range from 2.8‰ to 4.3‰, whereas the δ34S values of molybdenite range from 2.9‰ to 6.2‰. The data suggest both magmatic and crustal sources of sulfur. The δD and δ18O values for the hydrothermal fluids are -57.2‰ to -84.4‰ and 8.0‰ to -3.2‰, respectively. The fluid inclusion and stable data indicate that the pre-ore hydrothermal fluids were mostly of magmatic origin, but the fluids responsible for ore deposition were mixed magmatic and meteoric, and eventually meteoric water dominated the system in the post-ore stage.

16. Coke 'fines' bin at Furnace D. After delivery to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. Coke 'fines' bin at Furnace D. After delivery to the trestle bins, the coke was screened and the coke 'fines' or breeze, were transported by conveyor to the coke fines bins where it was collected and leaded into dump trucks. The coke fines were then sold for fuel to a sinter plant in Lorain, Ohio. - Central Furnaces, 2650 Broadway, east bank of Cuyahoga River, Cleveland, Cuyahoga County, OH

Qatar: Background and U.S. Relations

DTIC Science & Technology

2014-11-04

Ahmed bin Abdullah bin Ziad Al Mahmoud Foreign Minister Khalid Bin Mohammed Al Attiyah Minister of Energy and Industry Mohammed bin Saleh al Sada...about voter franchise extension were resolved.5 The Advisory Council would have oversight authority over the Council of Ministers and would be able...Sunni armed groups in Syria has the potential to have a more lasting impact on the region, but has challenged the traditional Qatari preference for

Toward zero waste events: Reducing contamination in waste streams with volunteer assistance.

PubMed

Zelenika, Ivana; Moreau, Tara; Zhao, Jiaying

2018-06-01

Public festivals and events generate a tremendous amount of waste, especially when they involve food and drink. To reduce contamination across waste streams, we evaluated three types of interventions at a public event. In a randomized control trial, we examined the impact of volunteer staff assistance, bin tops, and sample 3D items with bin tops, on the amount of contamination and the weight of the organics, recyclable containers, paper, and garbage bins at a public event. The event was the annual Apple Festival held at the University of British Columbia, which was attended by around 10,000 visitors. We found that contamination was the lowest in the volunteer staff condition among all conditions. Specifically, volunteer staff reduced contamination by 96.1% on average in the organics bin, 96.9% in the recyclable containers bin, 97.0% in the paper bin, and 84.9% in the garbage bin. Our interventions did not influence the weight of the materials in the bins. This finding highlights the impact of volunteers on reducing contamination in waste streams at events, and provides suggestions and implications for waste management for event organizers to minimize contamination in all waste streams to achieve zero waste goals. Copyright © 2018. Published by Elsevier Ltd.

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

28 CFR 79.62 - Criteria for eligibility for claims by ore transporters.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ore transporters. 79.62 Section 79.62 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CLAIMS UNDER THE RADIATION EXPOSURE COMPENSATION ACT Eligibility Criteria for Claims by Ore Transporters § 79.62 Criteria for eligibility for claims by ore transporters. To establish eligibility for compensation...

28 CFR 79.62 - Criteria for eligibility for claims by ore transporters.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ore transporters. 79.62 Section 79.62 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CLAIMS UNDER THE RADIATION EXPOSURE COMPENSATION ACT Eligibility Criteria for Claims by Ore Transporters § 79.62 Criteria for eligibility for claims by ore transporters. To establish eligibility for compensation...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

28 CFR 79.62 - Criteria for eligibility for claims by ore transporters.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ore transporters. 79.62 Section 79.62 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CLAIMS UNDER THE RADIATION EXPOSURE COMPENSATION ACT Eligibility Criteria for Claims by Ore Transporters § 79.62 Criteria for eligibility for claims by ore transporters. To establish eligibility for compensation...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

28 CFR 79.62 - Criteria for eligibility for claims by ore transporters.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ore transporters. 79.62 Section 79.62 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CLAIMS UNDER THE RADIATION EXPOSURE COMPENSATION ACT Eligibility Criteria for Claims by Ore Transporters § 79.62 Criteria for eligibility for claims by ore transporters. To establish eligibility for compensation...

Improved Taxation Rate for Bin Packing Games

NASA Astrophysics Data System (ADS)

Kern, Walter; Qiu, Xian

A cooperative bin packing game is a N-person game, where the player set N consists of k bins of capacity 1 each and n items of sizes a 1, ⋯ ,a n . The value of a coalition of players is defined to be the maximum total size of items in the coalition that can be packed into the bins of the coalition. We present an alternative proof for the non-emptiness of the 1/3-core for all bin packing games and show how to improve this bound ɛ= 1/3 (slightly). We conjecture that the true best possible value is ɛ= 1/7.

Translations on Eastern Europe, Scientific Affairs, Number 543

DTIC Science & Technology

1977-04-29

They are economically more effective than those now used, for one gram of glass can replace ten kilograms of copper wire. For several years such a...and 62 times for nonferrous ores, the greatest increase being recorded for copper bearing ores. 1. Iron Ores Overall, the iron ore deposits which...percent S. 30 Intensive research and design work is being conducted to exploit two deposits of poor copper ore (0.25-D.35 percent Cu), a deposit of

32. INTERIOR VIEW LOOKING NORTH ON THE ORE BREAKER LEVEL. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. INTERIOR VIEW LOOKING NORTH ON THE ORE BREAKER LEVEL. THE ORE BREAKER, A BLAKE JAW CRUSHER, IS IN THE BOX IN THE LEFT OF THE PHOTOGRAPH, THE ORE TO BE BROKEN IS FED INTO THE OPENING ON THE FLOOR AND NEXT TO ORE BREAKER BOX. THE GRIZZLY BARS ARE ON THE RIGHT AND THE PULLEYS FROM THE POWER SYSTEM ARE OVERHEAD. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Acid pre-treatment method for in situ ore leaching

DOEpatents

Mallon, R.G.; Braun, R.L.

1975-10-28

An acid leaching method is described for the recovery of a desired element from a subterranean rubblized body of primary ore containing the element and also having associated therewith a carbonate mineral wherein the rubblized ore body is flooded with an aqueous acidic solution in order to release carbon dioxide from the associated carbonate mineral. After a substantial portion of the available carbon dioxide is released and removed from the ore body, as by venting to the atmosphere, an oxidizing gas is introduced into the flooded, rubblized ore to oxidize the ore and form an acid leach solution effective in the presence of the dissolved oxidizing gas to dissolve the ore and cause the desired element to go into solution. The leach solution is then circulated to the surface where the metal values are recovered therefrom.

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 440.30 - Applicability; description of the uranium, radium and vanadium ores subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... uranium, radium and vanadium ores subcategory. 440.30 Section 440.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.30 Applicability; description of the...

40 CFR 63.9582 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing... applies to each new and existing affected source at your taconite iron ore processing plant. (b) The affected sources are each new or existing ore crushing and handling operation, ore dryer, indurating...

40 CFR 63.9582 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing... applies to each new and existing affected source at your taconite iron ore processing plant. (b) The affected sources are each new or existing ore crushing and handling operation, ore dryer, indurating...

40 CFR 63.9582 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing... applies to each new and existing affected source at your taconite iron ore processing plant. (b) The affected sources are each new or existing ore crushing and handling operation, ore dryer, indurating...

40 CFR 63.9582 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing... applies to each new and existing affected source at your taconite iron ore processing plant. (b) The affected sources are each new or existing ore crushing and handling operation, ore dryer, indurating...

17. ORE DOCK, LOOKING EAST FROM HULETT NO. 1. WHEN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. ORE DOCK, LOOKING EAST FROM HULETT NO. 1. WHEN BUILT IN 1911-1912, THIS WAS THE LARGEST ORE-UNLOADING DOCK ON THE GREAT LAKES. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

40 CFR 63.9582 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing... applies to each new and existing affected source at your taconite iron ore processing plant. (b) The affected sources are each new or existing ore crushing and handling operation, ore dryer, indurating...

40 CFR 440.30 - Applicability; description of the uranium, radium and vanadium ores subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... uranium, radium and vanadium ores subcategory. 440.30 Section 440.30 Protection of Environment... SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.30 Applicability; description of the uranium, radium and vanadium ores subcategory. The provisions of this subpart C are applicable to...

[Source apportionment of soil heavy metals in Jiapigou goldmine based on the UNMIX model].

PubMed

Ai, Jian-chao; Wang, Ning; Yang, Jing

2014-09-01

The paper determines 16 kinds of metal elements' concentration in soil samples which collected in Jipigou goldmine upper the Songhua River. The UNMIX Model which was recommended by US EPA to get the source apportionment results was applied in this study, Cd, Hg, Pb and Ag concentration contour maps were generated by using Kriging interpolation method to verify the results. The main conclusions of this study are: (1)the concentrations of Cd, Hg, Pb and Ag exceeded Jilin Province soil background values and enriched obviously in soil samples; (2)using the UNMIX Model resolved four pollution sources: source 1 represents human activities of transportation, ore mining and garbage, and the source 1's contribution is 39. 1% ; Source 2 represents the contribution of the weathering of rocks and biological effects, and the source 2's contribution is 13. 87% ; Source 3 is a comprehensive source of soil parent material and chemical fertilizer, and the source 3's contribution is 23. 93% ; Source 4 represents iron ore mining and transportation sources, and the source 4's contribution is 22. 89%. (3)the UNMIX Model results are in accordance with the survey of local land-use types, human activities and Cd, Hg and Pb content distributions.

Tracking natural and anthropogenic Pb exposure to its geological source.

PubMed

Evans, Jane; Pashley, Vanessa; Madgwick, Richard; Neil, Samantha; Chenery, Carolyn

2018-01-31

Human Pb exposure comes from two sources: (i) natural uptake through ingestion of soils and typified by populations that predate mining activity and (ii) anthropogenic exposure caused by the exposure to Pb derived from ore deposits. Currently, the measured concentration of Pb within a sample is used to discriminate between these two exposure routes, with the upper limit for natural exposure in skeletal studies given as 0.5 or 0.7 mg/kg in enamel and 0.5/0.7 μg/dL in blood. This threshold approach to categorising Pb exposure does not distinguish between the geological origins of the exposure types. However, Pb isotopes potentially provide a more definitive means of discriminating between sources. Whereas Pb from soil displays a crustal average 238 U/ 204 Pb (μ) value of c 9.7, Pb from ore displays a much wider range of evolution pathways. These characteristics are transferred into tooth enamel, making it possible to characterize human Pb exposure in terms of the primary source of ingested Pb and to relate mining activity to geotectonic domains. We surmise that this ability to discriminate between silicate and sulphide Pb exposure will lead to a better understanding of the evolution of early human mining activity and development of exposure models through the Anthropocene.

Methods of steel manufacturing - The electric arc furnace

NASA Astrophysics Data System (ADS)

Dragna, E. C.; Ioana, A.; Constantin, N.

2018-01-01

Initially, the carbon content was reduced by mixing “the iron” with metallic ingots in ceramic crucibles/melting pots, with external heat input. As time went by the puddling procedure was developed, a procedure which also assumes a mixture with oxidized iron ore. In 1856 Bessemer invented the convertor, thus demonstrating that steel can be obtained following the transition of an air stream through the liquid pig iron. The invention of Thomas, a slightly modified basic-lined converter, fostered the desulphurization of the steel and the removal of the phosphate from it. During the same period, in 1865, in Sireuil, the Frenchman Martin applies Siemens’ heat regeneration invention and brings into service the furnace with a charge composed of iron pig, scrap iron and iron ore, that produces a high quality steel [1]. An act worthy of being highlighted within the scope of steelmaking is the start-up of the converter with oxygen injection at the upper side, as there are converters that can produce 400 tons of steel in approximately 50 minutes. Currently, the share of the steel produced in electric arc furnaces with a charge composed of scrap iron has increased. Due to this aspect, the electric arc furnace was able to impose itself on the market.

Distribution of hybrid entanglement and hyperentanglement with time-bin for secure quantum channel under noise via weak cross-Kerr nonlinearity.

PubMed

Heo, Jino; Kang, Min-Sung; Hong, Chang-Ho; Yang, Hyung-Jin; Choi, Seong-Gon; Hong, Jong-Phil

2017-08-31

We design schemes to generate and distribute hybrid entanglement and hyperentanglement correlated with degrees of freedom (polarization and time-bin) via weak cross-Kerr nonlinearities (XKNLs) and linear optical devices (including time-bin encoders). In our scheme, the multi-photon gates (which consist of XKNLs, quantum bus [qubus] beams, and photon-number-resolving [PNR] measurement) with time-bin encoders can generate hyperentanglement or hybrid entanglement. And we can also purify the entangled state (polarization) of two photons using only linear optical devices and time-bin encoders under a noisy (bit-flip) channel. Subsequently, through local operations (using a multi-photon gate via XKNLs) and classical communications, it is possible to generate a four-qubit hybrid entangled state (polarization and time-bin). Finally, we discuss how the multi-photon gate using XKNLs, qubus beams, and PNR measurement can be reliably performed under the decoherence effect.

Selection of 3013 Containers for Field Surveillance. Fiscal Year 2016 Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, Elizabeth J.; Berg, John M.; Cheadle, Jesse

2016-04-19

This update is the eighth in a series of reports that document the binning and sample selection of 3013 containers for the Field Surveillance program as part of the Integrated Surveillance Program. This report documents changes made to both the container binning assignments and the sample selection approach. Binning changes documented in this update are a result of changes to the prompt gamma calibration curves and the reassignment of a small number of Hanford items from the Pressure bin to the Pressure and Corrosion (P&C) bin. Field Surveillance sample selection changes are primarily a result of focusing future destructive examinationsmore » (DEs) on the potential for stress corrosion cracking in higher moisture containers in the P&C bin. The decision to focus the Field Surveillance program on higher moisture items is based on findings from both the Shelf-life testing program and DEs.« less

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. THE STAMP AN MORTAR BOX ARE ON THE LEFT AND THE FEEDER WITH ITS FEEDER DISK IS ON THE RIGHT. NOTE THE COLLAR ON THE CENTER STAMP STEM (UPPER LEFT CORNER OF THE IMAGE) THAT ACTIVATES THE LEVER IN THE CENTER OF THE PHOTO. THE COLLAR IS POSITIONED SUCH THAT WHEN THE LEVEL OF THE MATERIAL REACHES A LOW POINT IN THE MORTAR BOX IT PUSHES DOWN ON THE LEVER WHICH IN TURN ACTIVATES THE AUTOMATIC FEEDER DRIVE MECHANISM WHICH THEM DELIVERS ORE INTO THE BACKSIDE OF THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

62. VIEW OF MILL SOLUTION TANKS FLOOR FROM WEST. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

62. VIEW OF MILL SOLUTION TANKS FLOOR FROM WEST. THE BOTTOM OF MILL SOLUTION TANK No. 1 IS IN THE LOWER RIGHT QUADRANT UNDER A PILE OF SOLUTION SEDIMENT. JOISTS OF TANK No. 2 ARE ABOVE AND SLIGHTLY LEFT OF No. 1. THE BOTTOM OF THE MILL SOLUTION SURGE TANK WITH ATTACHED DISCHARGE PIPE IS VISIBLE ON LOWER RIGHT HAND EDGE OF VIEW; TANKS ORIGINALLY SAT ON DIAGONAL BEAM CUTTING ACROSS UPPER LEFT CORNER OF VIEW. DISCHARGE LAUNDER FROM THE UNOXIDIZED ORE CIRCUIT PIERCES THE FOUNDATION WALL ABOVE TANK No. 1 (FOR DETAIL SEE SD-2-61). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Phase composition of Katowice - Wełnowiec pytometallurgical slags: preliminary SEM study

NASA Astrophysics Data System (ADS)

Warchulski, Rafał; Szopa, Krzysztof

2014-09-01

Exploitation on Zn-Pb ores in Upper Silesia region dates back to the XIII century. Analyzed slags are associated with Hohenlohe smelting plant which started its work in 1804 as an iron smelter, and continued as zinc smelter since 1873. Waste material from smelting plant production was stored in Katowice - Wełnowiec, although nowadays most of it has been used for commercial purposes. Slags are composed of silicates and aluminosilicates, e.g. willemite, pyroxene- and melilite-group, K-feldspar accompanied by silico-phosphates close to perhamite, harrisonite and arsenate-chloride with composition similar to nealite. Chemical composition of most phases is simple with some unique substitutions in case of Sr and Ce

Phase Composition of Katowice - Wełnowiec Pytometallurgical Slags: Preliminary SEM Study

NASA Astrophysics Data System (ADS)

Warchulski, Rafał; Szopa, Krzysztof

2014-09-01

Exploitation on Zn-Pb ores in Upper Silesia region dates back to the XIII century. Analyzed slags are associated with Hohenlohe smelting plant which started its work in 1804 as an iron smelter, and continued as zinc smelter since 1873. Waste material from smelting plant production was stored in Katowice - Wełnowiec, although nowadays most of it has been used for commercial purposes. Slags are composed of silicates and aluminosilicates, e.g. willemite, pyroxene- and melilite-group, K-feldspar accompanied by silico-phosphates close to perhamite, harrisonite and arsenate-chloride with composition similar to nealite. Chemical composition of most phases is simple with some unique substitutions in case of Sr and Ce.

Iron-ore resources of the United States including Alaska and Puerto Rico, 1955

USGS Publications Warehouse

Carr, Martha S.; Dutton, Carl E.

1959-01-01

The importance of iron ore, the basic raw material of steel, as a fundamental mineral, resource is shown by the fact that about 100 million long tons of steel is used annually in the economy of the United States, as compared with a combined total of about 5 million long tons of copper, lead, zinc, and aluminum. Satisfying this annual demand for steel requires about 110 million tons of iron ore and 70 million tons of scrap iron and steel. The average annual consumption of iron ore in the United States from 1951 to 1955, inclusive, was about 110 million long tons, which is about twice the annual average from 1900 to 1930. Production of iron ore in the United States in this 5-year period averaged approximately 100 million long tons annually, divided by regions as follows (in percent): Lake Superior, 84.1; southeastern, 6.7; western, 6.7; northeastern, 1.4; and central and gulf, 1.1. Mining of iron ore began in the American Colonies about 1619, and for 225 years it was limited to eastern United States where fuel and markets were readily available. Production of iron ore from the Lake Superior region began in 1846; the region became the leading domestic source by 1890, and the Mesabi range in Minnesota has been the world's most productive area since 1896. Proximity of raw materials, water transportation, and markets has resulted in centralization of the country's iron and steel industry in the lower Great Lakes area. Increased imports of iron ore being delivered to eastern United States as well as demands for steel in nearby markets have given impetus to expansion in the steel-making capacity in this area. The four chief iron-ore minerals - hematite, liminite, magnetite, and siderite - are widely distributed but only locally form deposits of sufficient tonnage and grade to be commercially valuable at the present time. The iron content of these minerals, of which hematite is the most important, ranges from 48 percent in siderite to 72 percent in magnetite, but as these minerals are associated with other rock-forming minerals, the iron content of marketable ore has a lower range from 30 to 67 percent.Chemical constituents other than iron also are important in determining the marketability of iron ore. Although some iron ores can be used in the blast furnace as mined, others must first be improved either chemically by reduction of undesirable constituents, or physically by aggregation. Phosphorus and sulfur particularly are common deleterious elements; excessive silica is also undesirable but within certain limits can be controlled by additional flux. Lime and magnesia are beneficial in specified amounts because of their fluxing qualities, and a small amount of alumina improves the fluidity of slag. Manganese is especially desirable as a deoxidizing and desulfurizing agent. Titanium, chromium, and nickel must also be considered in the use of ore containing these elements.The principal iron-ore deposits in the United States have been formed by three processes. Hematite-bearing bedded deposits such as those at Birmingham, Ala., are marine sedimentary rocks which, except for weathering along the outcrop, have remained practically unaltered since deposition. Deposits of the Lake Superior region, also in sedimentary strata, originally had a slightly lower iron content than those at-Birmingham, but ore bodies of hematite and limonite were formed by removal of other constituents in solution after deposition of the beds, with a relative increase of iron content in the material remaining. Limestone adjacent to igneous intrusions has been replaced by magnetite deposits at Cornwall, Pa., and by hematite-magnetite deposits near Cedar City, Utah. Magnetite deposits in New Jersey and in the Adirondack Mountains of New York are generally believed to have been formed by replacement of grains of other minerals in metamorphic rocks. Iron-ore resources are made up of reserves of iron ore, material usable under existing economic and technologic conditions; and potential ore, material likely to become usable under more favorable conditions. The tonnage and grade of material of combined reserves and potential ore in each of the deposits known or believed to contain at least 200,000 long tons of iron-ore resources are tabulated in this report, and numerous sources of additional information are given in a selected bibliography. The total domestic iron-ore resources are estimated at approximately 75,000 million long tons of crude ore. About 10,000 million tons of the resources is reserves of crude ore that will probably yield 5,500 million tons of concentrates and direct-shipping ore. About 65,000 million tons is potential ore and may yield 25,000 million tons of concentrates and some direct-shipping ore.

Crustal structure in the Kiruna area, northern Sweden, based on seismic reflection profiling

NASA Astrophysics Data System (ADS)

Juhojuntti, Niklas; Bergman, Stefan; Olsson, Sverker

2013-04-01

Northernmost Sweden is currently one of the most active mining areas in Europe. In order to better understand the regional three-dimensional crustal structure and to support deep ore exploration, we have acquired a 74 km long seismic reflection profile in the Kiruna area. The upper crust in this area is largely composed of various supracrustal units, which are dominated by metabasalts, acidic metavolcanics and clastic metasedimentary rocks, resting on an Archaean metagranitoid complex. All of these units have been intruded by plutonic rocks, and to variable degrees folded, sheared and metamorphosed, during the Svecokarelian orogeny. The profile crosses several steep ductile shear zones, some of which extend for hundreds of kilometres along strike. Many of the lithological contacts and deformation zones are expected to be seismically reflective. The profile is located only a few kilometres from the world's largest underground iron-ore mine in Kiruna, and closer to the profile there are several known ore bodies, some of which are active exploration targets. For the seismic recording we used approximately 350 geophones in split-spread configuration, at a separation of 25 m. The main seismic source was the Vibsist system (an impact source), which normally was employed at every geophone station. We also fired explosive charges (8-16 kg) at a few locations distributed along the profile to image deeper structures, although at very low resolution. Wireless seismometers were placed along and to the side of the profile, mainly in order to achieve better velocity control and to study out-of-the-plane reflections. Some mining blasts in Kiruna were also recorded. The upper crust in the area is quite reflective, most clearly demonstrated by the dynamite shot records. Some of the reflections appear to originate from steeply dipping structures. The dynamite shot records show a set of reflections at 3-4 s twt, corresponding to a depth of roughly 10 km, the explanation for which is unknown at present. Many of the dynamite shot records also show reflections from deeper in the crust. The preliminary stacked sections based on the Vibsist data show reflections down to depths of at least 5 km, some of which have been tentatively interpreted to originate at the contacts between basalts and felsic metavolcanics. In the further data analysis, special focus is given to the processing of reflections from steeply dipping structures and to the integration of the low-fold dynamite and high-fold Vibsist data.

Mapping global biodiversity connections with DNA barcodes: Lepidoptera of Pakistan.

PubMed

Ashfaq, Muhammad; Akhtar, Saleem; Rafi, Muhammad Athar; Mansoor, Shahid; Hebert, Paul D N

2017-01-01

Sequences from the DNA barcode region of the mitochondrial COI gene are an effective tool for specimen identification and for the discovery of new species. The Barcode of Life Data Systems (BOLD) (www.boldsystems.org) currently hosts 4.5 million records from animals which have been assigned to more than 490,000 different Barcode Index Numbers (BINs), which serve as a proxy for species. Because a fourth of these BINs derive from Lepidoptera, BOLD has a strong capability to both identify specimens in this order and to support studies of faunal overlap. DNA barcode sequences were obtained from 4503 moths from 329 sites across Pakistan, specimens that represented 981 BINs from 52 families. Among 379 species with a Linnaean name assignment, all were represented by a single BIN excepting five species that showed a BIN split. Less than half (44%) of the 981 BINs had counterparts in other countries; the remaining BINs were unique to Pakistan. Another 218 BINs of Lepidoptera from Pakistan were coupled with the 981 from this study before being compared with all 116,768 BINs for this order. As expected, faunal overlap was highest with India (21%), Sri Lanka (21%), United Arab Emirates (20%) and with other Asian nations (2.1%), but it was very low with other continents including Africa (0.6%), Europe (1.3%), Australia (0.6%), Oceania (1.0%), North America (0.1%), and South America (0.1%). This study indicates the way in which DNA barcoding facilitates measures of faunal overlap even when taxa have not been assigned to a Linnean species.

Mapping global biodiversity connections with DNA barcodes: Lepidoptera of Pakistan

PubMed Central

Akhtar, Saleem; Rafi, Muhammad Athar; Mansoor, Shahid; Hebert, Paul D. N.

2017-01-01

Sequences from the DNA barcode region of the mitochondrial COI gene are an effective tool for specimen identification and for the discovery of new species. The Barcode of Life Data Systems (BOLD) (www.boldsystems.org) currently hosts 4.5 million records from animals which have been assigned to more than 490,000 different Barcode Index Numbers (BINs), which serve as a proxy for species. Because a fourth of these BINs derive from Lepidoptera, BOLD has a strong capability to both identify specimens in this order and to support studies of faunal overlap. DNA barcode sequences were obtained from 4503 moths from 329 sites across Pakistan, specimens that represented 981 BINs from 52 families. Among 379 species with a Linnaean name assignment, all were represented by a single BIN excepting five species that showed a BIN split. Less than half (44%) of the 981 BINs had counterparts in other countries; the remaining BINs were unique to Pakistan. Another 218 BINs of Lepidoptera from Pakistan were coupled with the 981 from this study before being compared with all 116,768 BINs for this order. As expected, faunal overlap was highest with India (21%), Sri Lanka (21%), United Arab Emirates (20%) and with other Asian nations (2.1%), but it was very low with other continents including Africa (0.6%), Europe (1.3%), Australia (0.6%), Oceania (1.0%), North America (0.1%), and South America (0.1%). This study indicates the way in which DNA barcoding facilitates measures of faunal overlap even when taxa have not been assigned to a Linnean species. PMID:28339501

Untangling taxonomy: a DNA barcode reference library for Canadian spiders.

PubMed

Blagoev, Gergin A; deWaard, Jeremy R; Ratnasingham, Sujeevan; deWaard, Stephanie L; Lu, Liuqiong; Robertson, James; Telfer, Angela C; Hebert, Paul D N

2016-01-01

Approximately 1460 species of spiders have been reported from Canada, 3% of the global fauna. This study provides a DNA barcode reference library for 1018 of these species based upon the analysis of more than 30,000 specimens. The sequence results show a clear barcode gap in most cases with a mean intraspecific divergence of 0.78% vs. a minimum nearest-neighbour (NN) distance averaging 7.85%. The sequences were assigned to 1359 Barcode index numbers (BINs) with 1344 of these BINs composed of specimens belonging to a single currently recognized species. There was a perfect correspondence between BIN membership and a known species in 795 cases, while another 197 species were assigned to two or more BINs (556 in total). A few other species (26) were involved in BIN merges or in a combination of merges and splits. There was only a weak relationship between the number of specimens analysed for a species and its BIN count. However, three species were clear outliers with their specimens being placed in 11-22 BINs. Although all BIN splits need further study to clarify the taxonomic status of the entities involved, DNA barcodes discriminated 98% of the 1018 species. The present survey conservatively revealed 16 species new to science, 52 species new to Canada and major range extensions for 426 species. However, if most BIN splits detected in this study reflect cryptic taxa, the true species count for Canadian spiders could be 30-50% higher than currently recognized. © 2015 The Authors. Molecular Ecology Resources Published by John Wiley & Sons Ltd.

The recovery of gold from refractory ores by the use of carbon-in-chlorine leaching

NASA Astrophysics Data System (ADS)

Greaves, John N.; Palmer, Glenn R.; White, William W.

1990-09-01

Recently, the U.S. Bureau of Mines examined the recovery of gold by chlorination of refractory carbonaceous and sulfidic ores, comparing various treatment methods in which a ground ore pulp is contacted with chlorine gas and activated carbon is added to the pulp for a carbon-in-chlorine leach (CICL). The objective of this research was to demonstrate the basic feasibility of CICL technology. Results showed that the organic carbon deactivating environment of CICL lowers, but does not eliminate, the adsorption of gold on activated carbon. In this environment, the refractory ore is altered, and gold is extracted and then recovered on activated carbon. With highly carbonaceous ores, CICL achieved a higher recovery than with primarily sulfidic refractory ores. Basic cyanide amenability testing of two carbonaceous ores achieved recoveries of only 5.5% and 46%. With CICL treatment, recoveries on carbon were 90% and 92%.

Solubility and chemistry of materials encountered by beryllium mine and ore extraction workers: relation to risk.

PubMed

Deubner, David C; Sabey, Philip; Huang, Wenjie; Fernandez, Diego; Rudd, Abigail; Johnson, William P; Storrs, Jason; Larson, Rod

2011-10-01

Beryllium mine and ore extraction mill workers have low rates of beryllium sensitization and chronic beryllium disease relative to the level of beryllium exposure. The objective was to relate these rates to the solubility and composition of the mine and mill materials. Medical surveillance and exposure data were summarized. Dissolution of BeO, ore materials and beryllium hydroxide, Be(OH)(2) was measured in synthetic lung fluid. The ore materials were more soluble than BeO at pH 7.2 and similar at pH 4.5. Be(OH)(2) was more soluble than BeO at both pH. Aluminum dissolved along with beryllium from ore materials. Higher solubility of beryllium ore materials and Be(OH)(2) at pH 7.2 might shorten particle longevity in the lung. The aluminum content of the ore materials might inhibit the cellular immune response to beryllium.

CONTEXT VIEW ALONG EXISTING PERIMETER TRACKS LOOKING OVER IRON ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CONTEXT VIEW ALONG EXISTING PERIMETER TRACKS LOOKING OVER IRON ORE CARS TOWARDS WESTERN SIDE OF CLEVELAND BULK TERMINAL BUILDINGS AND A SELF-UNLOADING IRON ORE SHIP AT DOCK. LOOKING SOUTHWEST. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Geochemical features of the ore-bearing medium in uranium deposits in the Khiagda ore field

NASA Astrophysics Data System (ADS)

Kochkin, B. T.; Solodov, I. N.; Ganina, N. I.; Rekun, M. L.; Tarasov, N. N.; Shugina, G. A.; Shulik, L. S.

2017-09-01

The Neogene uranium deposits of the Khiagda ore field (KOF) belong to the paleovalley variety of the hydrogene type and differ from other deposits of this genetic type in the geological and geochemical localization conditions. The contemporary hydrogeochemical setting and microbiological composition of ore-bearing medium are discussed. The redox potential of the medium (Eh is as low as-400 mV) is much lower than those established at other hydrogenic deposits, both ancient Late Mesozoic and young Late Alpine, studied with the same methods in Russia, Uzbekistan, and southern Kazakhstan. The pH of subsurface water (6.86-8.13) differs in significant fluctuations both between neighboring deposits and within individual ore lodes. Hydrogen-forming and denitrifying bacteria are predominant in microbiological populations, whereas sulfate-reducing bacteria are low-active. The consideration of these factors allowed us to describe the mechanism of uranium ore conservation as resulting from the development of the cryolithic zone, which isolates ore lodes from the effect of the external medium. Carbonated water supplied from the basement along fault zones also participates in the formation of the present-day hydrogeochemical setting. Based on the features of the ore-bearing medium, we propose a method of borehole in situ acid leaching to increase the efficiency of mining in the Khiagda ore field.

Radon emanation from low-grade uranium ore.

PubMed

Sahu, Patitapaban; Mishra, Devi Prasad; Panigrahi, Durga Charan; Jha, Vivekanand; Patnaik, R Lokeswara

2013-12-01

Estimation of radon emanation in uranium mines is given top priority to minimize the risk of inhalation exposure due to short-lived radon progeny. This paper describes the radon emanation studies conducted in the laboratory as well as inside an operating underground uranium mine at Jaduguda, India. Some of the important parameters, such as grade/(226)Ra activity, moisture content, bulk density, porosity and emanation fraction of ore, governing the migration of radon through the ore were determined. Emanation from the ore samples in terms of emanation rate and emanation fraction was measured in the laboratory under airtight condition in glass jar. The in situ radon emanation rate inside the mine was measured from drill holes made in the ore body. The in situ(222)Rn emanation rate from the mine walls varied in the range of 0.22-51.84 × 10(-3) Bq m(-2) s(-1) with the geometric mean of 8.68 × 10(-3) Bq m(-2) s(-1). A significant positive linear correlation (r = 0.99, p < 0.001) between in situ(222)Rn emanation rate and the ore grade was observed. The emanation fraction of the ore samples, which varied in the range of 0.004-0.089 with mean value of 0.025 ± 0.02, showed poor correlation with ore grade and porosity. Empirical relationships between radon emanation rate and the ore grade/(226)Ra were also established for quick prediction of radon emanation rate from the ore body. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mineralogical and geochemical features of the alteration processes of magmatic ores in the Beni Bousera ultramafic massif (north Morocco)

NASA Astrophysics Data System (ADS)

Hajjar, Zaineb; Gervilla, Fernando; Essaifi, Abderrahim; Wafik, Amina

2017-08-01

The Beni Bousera ultramafic massif (Internal Rif, Morocco) is characterized by the presence of two types of small-scale magmatic mineralizations (i) a mineralization consisting mainly of chromite and Ni arsenides associated to orthopyroxene and cordierite (Cr-Ni ores), and (ii) a mineralization mainly composed of magmatic Fe-Ni-Cu sulfides containing variable amounts of graphite and chromite associated to phlogopite, clinopyroxène and plagioclase (S-G ores). Theses ores underwent High-T (450-550 °C) and Low-T (150-300 °C) alteration processes. The High-T alteration processes are tentatively related to intrusion of leucogranite dykes. They are preserved in the Galaros Cr-Ni ore deposit where nickeline is partly dissolved and transformed to maucherite, and orthopyroxene alters to phlogopite. Ni and Co were mobilized to the fluid phase, rising up their availability and promoting their diffusion into chromite and phlogopite, which have significantly higher contents in Ni and Co in phlogopite-rich ores than in orthopyroxene- and nickeline-rich ones. The Low-T alteration processes are related to serpentinization/weathering spatially associated with a regional shear zone. They affected both the Cr-Ni and S-G ores. In the Cr-Ni ores, Ni-arsenides were completely leached out while chromite is fractured within a matrix of chlorite, vermiculite and Ni-rich serpentine. In S-G ores, the silicates were altered into amphibole, Fe-rich chlorite and pectolite in clinopyroxene- and plagioclase-bearing ores while sulfides were completely leached out in phlogopite-bearing ores where iron oxides and hydroxides, and Fe-rich vermiculite were deposited. Chromite composition is not affected by the Low-T alteration processes.

Using apatite to discriminate synchronous ore-associated and barren granitoid rocks: A case study from the Edong metallogenic district, South China

NASA Astrophysics Data System (ADS)

Duan, Deng-Fei; Jiang, Shao-Yong

2018-06-01

In order to find criteria to discriminate the synchronous ore-associated and barren granitoid rocks, we have determined apatite chemistry associated with ore-associated (Cu-Au) and barren granitoid rocks in the Edong district of the Middle and Lower Yangtze River metallogenic belt, South China. Both rock types give zircon U-Pb ages between 135.0 and 138.7 Ma. Apatite has a higher volatile and Li content (Cl: 0.19-0.57 wt%, average 0.35 wt%, SO3: 0.08-0.71 wt%, average 0.32 wt%, Li: 0.49-7.99 ppm, average 3.23 ppm) in ore-associated rocks than those in barren rocks (Cl: 0.09-0.31 wt%, average 0.16 wt%, SO3: 0.06-0.28 wt%, average 0.16 wt%, Li: 0.15-0.89 ppm, average 0.36 ppm). Apatite (La/Yb)N ratios and Eu/Eu* values are relatively high and show wider variation in ore-associated rocks than those in barren rocks. Apatite (La/Sm)N and (Yb/Sm)N show positive correlation in ore-associated rocks but negative in barren rocks. The higher volatile content occurs in ore-associated magma, favoring Cu-Au transportation and deposition. Furthermore, amphibole fractional crystallization in ore-associated magma further enriched the ore elements in the residual melt. Barren rocks may have undergone fluid exsolution before emplacement, which makes it barren in Cl, S and ore elements (Cu, S). These signatures emphases the significance of volatile and magma evolution in mineralization and indicate that analyses of magmatic apatite can serve to distinguish ore-associated from barren intrusions.

Application of the Geo-Anomaly Unit Concept in Quantitative Delineation and Assessment of Gold Ore Targets in Western Shandong Uplift Terrain, Eastern China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Yongqing, E-mail: ydonglai@mail.cgs.gov.cn; Zhao Pengda; Chen Jianguo

2001-03-15

A number of large and giant ore deposits have been discovered within the relatively small areas of lithospheric structure anomalies, including various boundary zones of tectonic plates. The regions have become the well-known intercontinental ore-forming belts, such as the circum-Pacific gold-copper, copper-molybdenum, and tungsten-tin metallogenic belts. These belts are typical geological anomalous areas. An investigation into the hydrothermal ore deposits in different regions in the former Soviet Union illustrated that the geologic structures of ore fields of almost all major commercial deposits have distinct features compared with the neighboring areas. These areas with distinct features are defined as geo-anomalies. Amore » geo-anomaly refers to such a geologic body or a combination of bodies that their composition, texture-structure, and genesis are significantly different from those of their surroundings. A geo-anomaly unit (GU) is an area containing distinct features that can be delineated with integrated ore-forming information using computer techniques on the basis of the geo-anomaly concept. Herein, the GU concept is illustrated by a case study of delineating the gold ore targets in the western Shandong uplift terrain, eastern China. It includes: (1) analyses of gold ore-forming factors; (2) compilation of normalized regional geochemical map and extraction of geochemical anomalies; (3) compilation of gravitational and aeromagnetic tectonic skeleton map and extraction of gravitational and aeromagnetic anomalies; (4) extraction of circular and linear anomalies from remote-sensing Landsat TM images; (5) establishment of a geo-anomaly conceptual model associated with known gold mineralization; (6) establishment of gold ore-forming favorability by computing techniques; and (7) delineation and assessment of ore-forming units. The units with high favorability are suggested as ore targets.« less

Idea of Identification of Copper Ore with the Use of Process Analyser Technology Sensors

NASA Astrophysics Data System (ADS)

Jurdziak, Leszek; Kaszuba, Damian; Kawalec, Witold; Król, Robert

2016-10-01

The Polish resources of the copper ore exploited by the KGHM S.A. underground mines are considered as one of the most complex in the world and - consequently - the most difficult to be processed. The ore consists of three lithology forms: dolomites, shales and sandstones but in different proportions which has a significant impact on the effectiveness of the grinding and flotation processes. The lithological composition of the ore is generally recognised in-situ but after being mined it is blended on its long way from various mining fields to the processing plant by the complex transportation system consisting of belt conveyors with numerous switching points, ore bunkers and shafts. Identification of the lithological composition of the ore being supplied to the processing plant should improve the adjustments of the ore processing machinery equipment aiming to decrease the specific processing (mainly grinding) energy consumption as well as increase the metal recovery. The novel idea of Process Analyser Technology (PAT) sensors - information carrying pellets, dropped into the transported or processed bulk material which can be read directly when needed - is investigated for various applications within the DISIRE project (a part of the SPIRE initiative, acting under the Horizon2020 framework program) and here is adopted for implementing the annotation the transported copper ore for the needs of ore processing plants control. The identification of the lithological composition of ore blended on its way to the processing plant can be achieved by an information system consisting of pellets that keep the information about the original location of the portions of conveyed ore, the digital, geological database keeping the data of in-situ lithology and the simulation models of the transportation system, necessary to evaluate the composition of the blended ore. The assumptions of the proposed solution and the plan of necessary in-situ tests (with the special respect to harsh environment of

Gold ores related to shear zones, West Santa Comba-Fervenza Area (Galicia, NW Spain): A mineralogical study

NASA Astrophysics Data System (ADS)

Castroviejo, R.

1990-12-01

Recent research has discovered high-grade Au ores in NNE-SSW trending shear zones in metamorphic proterozoic and palaeozoic terranes, some 40 km NW of Santiago de Compostela (NW Spain). The orebodies are bound to late-stage Hercynian structures, mainly due to brittle deformation, which are superimposed on earlier ductile shear zones, cutting through various catazonal lithologies, including ortho- and paragneisses, amphibolites, eclogites, and granites. Ore mineralogy, alteration, and ore textures define a frame whose main features are common to all prospects in the area. Main minerals are arsenopyrite and pyrite — accompanied by quartz, adularia, sericite, ± (tourmaline, chlorite, carbonates, graphite), as main gangue minerals -with subordinate amounts of boulangerite, bismuthinite, kobellite, jamesonite, chalcopyrite, marcasite, galena, sphalerite, rutile, titanite, scheelite, beryl, fluorite, and minor native gold, electrum, native bismuth, fahlore, pyrrhotite, mackinawite, etc., defining a meso-catathermal paragenesis. Detailed microscopic study allows the author to propose a general descriptive scheme of textural classification for this type of ore. Most of the ores fill open spaces or veins, seal cracks or cement breccias; disseminated ores with replacement features related to alteration (mainly silicification, sericitization, and adularization) are also observed. Intensive and repeated cataclasis is a common feature of many ores, suggesting successive events of brittle deformation, hydrothermal flow, and ore precipitation. Gold may be transported and accumulated in any of these events, but tends to be concentrated in later ones. The origin of the gold ores is explained in terms of hydrothermal discharge, associated with mainly brittle deformation and possibly related to granitic magmas, in the global tectonic frame of crustal evolution of West Galicia. The mineralogical and textural study suggests some criteria which will be of practical value for exploration and for ore processing. Ore grades can be improved by flotation of arsenopyrite. Non-conventional methods, such as pressure or bacterial leaching, may subsequently obtain a residue enriched in gold.

Binning in Gaussian Kernel Regularization

DTIC Science & Technology

2005-04-01

OSU-SVM Matlab package, the SVM trained on 966 bins has a comparable test classification rate as the SVM trained on 27,179 samples, but reduces the...71.40%) on 966 randomly sampled data. Using the OSU-SVM Matlab package, the SVM trained on 966 bins has a comparable test classification rate as the...the OSU-SVM Matlab package, the SVM trained on 966 bins has a comparable test classification rate as the SVM trained on 27,179 samples, and reduces

General Khalid Bin Waleed: Understanding the 7th Century Campaign against Sassanid Persian Empire from the Perspective of Operational Art

DTIC Science & Technology

2012-12-06

ABSTRACT This monograph investigates Khalid Bin Waleed’s seventh century (AD 633-634) campaign against the Sassanid Persian Empire in Mesopotamia to...Khalid Bin Waleed’s seventh century (AD 633-634) campaign against the Sassanid Persian Empire in Mesopotamia to trace the evidence that substantiates...Bin Waleed employed characteristics and elements of operational art to defeat the Persian forces in Mesopotamia . He established operational objectives

SeaWiFS technical report series. Volume 32: Level-3 SeaWiFS data products. Spatial and temporal binning algorithms

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); Acker, James G. (Editor); Campbell, Janet W.; Blaisdell, John M.; Darzi, Michael

1995-01-01

The level-3 data products from the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) are statistical data sets derived from level-2 data. Each data set will be based on a fixed global grid of equal-area bins that are approximately 9 x 9 sq km. Statistics available for each bin include the sum and sum of squares of the natural logarithm of derived level-2 geophysical variables where sums are accumulated over a binning period. Operationally, products with binning periods of 1 day, 8 days, 1 month, and 1 year will be produced and archived. From these accumulated values and for each bin, estimates of the mean, standard deviation, median, and mode may be derived for each geophysical variable. This report contains two major parts: the first (Section 2) is intended as a users' guide for level-3 SeaWiFS data products. It contains an overview of level-0 to level-3 data processing, a discussion of important statistical considerations when using level-3 data, and details of how to use the level-3 data. The second part (Section 3) presents a comparative statistical study of several binning algorithms based on CZCS and moored fluorometer data. The operational binning algorithms were selected based on the results of this study.

Geology and ore deposits of the Section 23 Mine, Ambrosia Lake District, New Mexico

USGS Publications Warehouse

Granger, H.C.; Santos, E.S.

1982-01-01

The section 23 mine is one of about 18 large uranium mines opened in sandstones of the fluvial Westwater Canyon Member of the Jurassic Morrison Formation in the Ambrosia Lake mining district during the early 1960s. The Ambrosia Lake district is one of several mining districts within the Grants mineral belt, an elongate zone containing many uranium deposits along the southern flank of the San Juan basin. Two distinct types of ore occur in the mine. Primary ore occurs as peneconcordant layers of uranium-rich authigenic organic matter that impregnates parts of the reduced sandstone host rocks and which are typically elongate in an east-southeast direction subparallel both to the sedimentary trends and to the present-day regional strike of the strata. These are called prefault or trend ores because of their early genesis and their elongation and alinement. A second type of ore in the mine is referred to as postfault, stacked, or redistributed ore. Its genesis was similar to that of the roll-type deposits in Tertiary rocks of Wyoming and Texas. Oxidation, related to the development of a large tongue of oxidized rock extending from Gallup to Ambrosia Lake, destroyed much of the primary ore and redistributed it as massive accumulations of lower grade ores bordering the redox interface at the edge of the tongue. Host rocks in the southern half of sec. 23 (T. 14 N., R. 10 W.) are oxidized and contain only remnants of the original, tabular, organic-rich ore. Thick bodies of roll-type ore are distributed along the leading edge of the oxidized zone, and pristine primary ore is found only near the north edge of the section. Organic matter in the primary ore was derived from humic acids that precipitated in the pores of the sandstones and fixed uranium as both coffinite and urano-organic compounds. Vanadium, molybdenum, and selenium are also associated with the ore. The secondary or roll-type ores are essentially free of organic carbon and contain uranium both as coffinite and uraninite. They also contain vanadium and selenium but are virtually devoid of molybdenum. Although much has been learned about these deposits since the time this study was conducted, in 1966, a great deal more study will by required to completely elucidate their geologic history.

Constraints on the composition of ore fluids and implications for mineralising events at the Cleo gold deposit, Eastern Goldfields Province, Western Australia

USGS Publications Warehouse

Brown, S.M.; Johnson, C.A.; Watling, R.J.; Premo, W.R.

2003-01-01

The Cleo gold deposit, 55 km south of Laverton in the Eastern Goldfields Province of Western Australia, is characterised by banded iron-formation (BIF)-hosted ore zones in the gently dipping Sunrise Shear Zone and high-grade vein-hosted ore in the Western Lodes. There is evidence that gold mineralisation in the Western Lodes (which occurred at ca 2655 Ma) post-dates the majority of displacement along the Sunrise Shear Zone, but it remains uncertain if the ore in both structures formed simultaneously or separately. Overall, the Pb, Nd, Sr, C. O and S isotopic compositions of ore-related minerals from both the Western Lodes and ore zones in the Sunrise Shear Zone are similar. Early low-salinity aqueous-carbonic fluids and late high-salinity fluids with similar characteristics are trapped in inclusions in quartz veins from both the Sunrise Shear Zone and the Western Lodes. The early CO2, CO2-H2O, and H2O- dominant inclusions are interpreted as being related to ore formation, and to have formed from a single low-salinity aqueous-carbonic fluid as a result of intermittent fluid immiscibility. Homogenisation temperatures indicate that these inclusions were trapped at approximately 280??C and at approximately 4 km depth, in the deeper epizonal range. Differences between the ore zones are detected in the trace-element composition of gold samples, with gold from the Sunrise Shear Zone enriched in Ni, Pb, Sn, Te and Zn, and depleted In As, Bi, Cd, Cu and Sb, relative to gold from the Western Lodes. Although there are differences in gold composition between the Sunrise Shear Zone and Western Lodes, and hence the metal content of ore fluids may have varied slightly between the different ore zones, no other systematic fluid or solute differences are detected between the ore zones. Given the fact that the ore fluids in each zone have very similar bulk properties, the considerable differences in gold grade, sulfide mineral abundance, and ore textures between the two ore zones most likely result from different gold-deposition mechanisms. The association of ore zones in the Sunrise Shear Zone with pyrite-replaced BIF suggests that wall-rock sulfidation was the most significant mechanism of gold precipitation, through the destabilisation of gold-bisulfide complexes. The Western Lodes, however, do not exhibit any host-rock preference and multistage veins commonly contain coarse-grained gold. Fluid-inclusion characteristics and breccia textures in veins in the Western Lodes suggest that rapid pressure changes, brought about by intermittent release of overpressured fluids and concomitant phase separation, are likely to have caused the destabilisation of gold-thiocomplexes, leading to formation of higher-grade gold ore zones.

Search for gravitational waves from intermediate mass binary black holes

NASA Astrophysics Data System (ADS)

Abadie, J.; Abbott, B. P.; Abbott, R.; Abbott, T. D.; Abernathy, M.; Accadia, T.; Acernese, F.; Adams, C.; Adhikari, R.; Affeldt, C.; Agathos, M.; Agatsuma, K.; Ajith, P.; Allen, B.; Amador Ceron, E.; Amariutei, D.; Anderson, S. B.; Anderson, W. G.; Arai, K.; Arain, M. A.; Araya, M. C.; Aston, S. M.; Astone, P.; Atkinson, D.; Aufmuth, P.; Aulbert, C.; Aylott, B. E.; Babak, S.; Baker, P.; Ballardin, G.; Ballmer, S.; Barayoga, J. C. B.; Barker, D.; Barone, F.; Barr, B.; Barsotti, L.; Barsuglia, M.; Barton, M. A.; Bartos, I.; Bassiri, R.; Bastarrika, M.; Basti, A.; Batch, J.; Bauchrowitz, J.; Bauer, Th. S.; Bebronne, M.; Beck, D.; Behnke, B.; Bejger, M.; Beker, M. G.; Bell, A. S.; Belletoile, A.; Belopolski, I.; Benacquista, M.; Berliner, J. M.; Bertolini, A.; Betzwieser, J.; Beveridge, N.; Beyersdorf, P. T.; Bilenko, I. A.; Billingsley, G.; Birch, J.; Biswas, R.; Bitossi, M.; Bizouard, M. A.; Black, E.; Blackburn, J. K.; Blackburn, L.; Blair, D.; Bland, B.; Blom, M.; Bock, O.; Bodiya, T. P.; Bogan, C.; Bondarescu, R.; Bondu, F.; Bonelli, L.; Bonnand, R.; Bork, R.; Born, M.; Boschi, V.; Bose, S.; Bosi, L.; Bouhou, B.; Braccini, S.; Bradaschia, C.; Brady, P. R.; Braginsky, V. B.; Branchesi, M.; Brau, J. E.; Breyer, J.; Briant, T.; Bridges, D. O.; Brillet, A.; Brinkmann, M.; Brisson, V.; Britzger, M.; Brooks, A. F.; Brown, D. A.; Bulik, T.; Bulten, H. J.; Buonanno, A.; Burguet-Castell, J.; Buskulic, D.; Buy, C.; Byer, R. L.; Cadonati, L.; Cagnoli, G.; Calloni, E.; Camp, J. B.; Campsie, P.; Cannizzo, J.; Cannon, K.; Canuel, B.; Cao, J.; Capano, C. D.; Carbognani, F.; Carbone, L.; Caride, S.; Caudill, S.; Cavaglià, M.; Cavalier, F.; Cavalieri, R.; Cella, G.; Cepeda, C.; Cesarini, E.; Chaibi, O.; Chalermsongsak, T.; Charlton, P.; Chassande-Mottin, E.; Chelkowski, S.; Chen, W.; Chen, X.; Chen, Y.; Chincarini, A.; Chiummo, A.; Cho, H.; Chow, J.; Christensen, N.; Chua, S. S. Y.; Chung, C. T. Y.; Chung, S.; Ciani, G.; Clara, F.; Clark, D. E.; Clark, J.; Clayton, J. H.; Cleva, F.; Coccia, E.; Cohadon, P.-F.; Colacino, C. N.; Colas, J.; Colla, A.; Colombini, M.; Conte, A.; Conte, R.; Cook, D.; Corbitt, T. R.; Cordier, M.; Cornish, N.; Corsi, A.; Costa, C. A.; Coughlin, M.; Coulon, J.-P.; Couvares, P.; Coward, D. M.; Cowart, M.; Coyne, D. C.; Creighton, J. D. E.; Creighton, T. D.; Cruise, A. M.; Cumming, A.; Cunningham, L.; Cuoco, E.; Cutler, R. M.; Dahl, K.; Danilishin, S. L.; Dannenberg, R.; D'Antonio, S.; Danzmann, K.; Dattilo, V.; Daudert, B.; Daveloza, H.; Davier, M.; Daw, E. J.; Day, R.; Dayanga, T.; De Rosa, R.; DeBra, D.; Debreczeni, G.; Del Pozzo, W.; del Prete, M.; Dent, T.; Dergachev, V.; DeRosa, R.; DeSalvo, R.; Dhurandhar, S.; Di Fiore, L.; Di Lieto, A.; Di Palma, I.; Di Paolo Emilio, M.; Di Virgilio, A.; Díaz, M.; Dietz, A.; Donovan, F.; Dooley, K. L.; Drago, M.; Drever, R. W. P.; Driggers, J. C.; Du, Z.; Dumas, J.-C.; Dwyer, S.; Eberle, T.; Edgar, M.; Edwards, M.; Effler, A.; Ehrens, P.; Endrőczi, G.; Engel, R.; Etzel, T.; Evans, K.; Evans, M.; Evans, T.; Factourovich, M.; Fafone, V.; Fairhurst, S.; Fan, Y.; Farr, B. F.; Fazi, D.; Fehrmann, H.; Feldbaum, D.; Feroz, F.; Ferrante, I.; Fidecaro, F.; Finn, L. S.; Fiori, I.; Fisher, R. P.; Flaminio, R.; Flanigan, M.; Foley, S.; Forsi, E.; Forte, L. A.; Fotopoulos, N.; Fournier, J.-D.; Franc, J.; Frasca, S.; Frasconi, F.; Frede, M.; Frei, M.; Frei, Z.; Freise, A.; Frey, R.; Fricke, T. T.; Friedrich, D.; Fritschel, P.; Frolov, V. V.; Fujimoto, M.-K.; Fulda, P. J.; Fyffe, M.; Gair, J.; Galimberti, M.; Gammaitoni, L.; Garcia, J.; Garufi, F.; Gáspár, M. E.; Gemme, G.; Geng, R.; Genin, E.; Gennai, A.; Gergely, L. Á.; Ghosh, S.; Giaime, J. A.; Giampanis, S.; Giardina, K. D.; Giazotto, A.; Gil, S.; Gill, C.; Gleason, J.; Goetz, E.; Goggin, L. M.; González, G.; Gorodetsky, M. L.; Goßler, S.; Gouaty, R.; Graef, C.; Graff, P. B.; Granata, M.; Grant, A.; Gras, S.; Gray, C.; Gray, N.; Greenhalgh, R. J. S.; Gretarsson, A. M.; Greverie, C.; Grosso, R.; Grote, H.; Grunewald, S.; Guidi, G. M.; Guido, C.; Gupta, R.; Gustafson, E. K.; Gustafson, R.; Ha, T.; Hallam, J. M.; Hammer, D.; Hammond, G.; Hanks, J.; Hanna, C.; Hanson, J.; Harms, J.; Harry, G. M.; Harry, I. W.; Harstad, E. D.; Hartman, M. T.; Haughian, K.; Hayama, K.; Hayau, J.-F.; Heefner, J.; Heidmann, A.; Heintze, M. C.; Heitmann, H.; Hello, P.; Hendry, M. A.; Heng, I. S.; Heptonstall, A. W.; Herrera, V.; Hewitson, M.; Hild, S.; Hoak, D.; Hodge, K. A.; Holt, K.; Holtrop, M.; Hong, T.; Hooper, S.; Hosken, D. J.; Hough, J.; Howell, E. J.; Hughey, B.; Husa, S.; Huttner, S. H.; Huynh-Dinh, T.; Ingram, D. R.; Inta, R.; Isogai, T.; Ivanov, A.; Izumi, K.; Jacobson, M.; James, E.; Jang, Y. J.; Jaranowski, P.; Jesse, E.; Johnson, W. W.; Jones, D. I.; Jones, G.; Jones, R.; Ju, L.; Kalmus, P.; Kalogera, V.; Kandhasamy, S.; Kang, G.; Kanner, J. B.; Kasturi, R.; Katsavounidis, E.; Katzman, W.; Kaufer, H.; Kawabe, K.; Kawamura, S.; Kawazoe, F.; Kelley, D.; Kells, W.; Keppel, D. G.; Keresztes, Z.; Khalaidovski, A.; Khalili, F. Y.; Khazanov, E. A.; Kim, B.; Kim, C.; Kim, H.; Kim, K.; Kim, N.; Kim, Y.-M.; King, P. J.; Kinzel, D. L.; Kissel, J. S.; Klimenko, S.; Kokeyama, K.; Kondrashov, V.; Koranda, S.; Korth, W. Z.; Kowalska, I.; Kozak, D.; Kranz, O.; Kringel, V.; Krishnamurthy, S.; Krishnan, B.; Królak, A.; Kuehn, G.; Kumar, R.; Kwee, P.; Lam, P. K.; Landry, M.; Lantz, B.; Lastzka, N.; Lawrie, C.; Lazzarini, A.; Leaci, P.; Lee, C. H.; Lee, H. K.; Lee, H. M.; Leong, J. R.; Leonor, I.; Leroy, N.; Letendre, N.; Li, J.; Li, T. G. F.; Liguori, N.; Lindquist, P. E.; Liu, Y.; Liu, Z.; Lockerbie, N. A.; Lodhia, D.; Lorenzini, M.; Loriette, V.; Lormand, M.; Losurdo, G.; Lough, J.; Luan, J.; Lubinski, M.; Lück, H.; Lundgren, A. P.; Macdonald, E.; Machenschalk, B.; MacInnis, M.; Macleod, D. M.; Mageswaran, M.; Mailand, K.; Majorana, E.; Maksimovic, I.; Man, N.; Mandel, I.; Mandic, V.; Mantovani, M.; Marandi, A.; Marchesoni, F.; Marion, F.; Márka, S.; Márka, Z.; Markosyan, A.; Maros, E.; Marque, J.; Martelli, F.; Martin, I. W.; Martin, R. M.; Marx, J. N.; Mason, K.; Masserot, A.; Matichard, F.; Matone, L.; Matzner, R. A.; Mavalvala, N.; Mazzolo, G.; McCarthy, R.; McClelland, D. E.; McGuire, S. C.; McIntyre, G.; McIver, J.; McKechan, D. J. A.; McWilliams, S.; Meadors, G. D.; Mehmet, M.; Meier, T.; Melatos, A.; Melissinos, A. C.; Mendell, G.; Mercer, R. A.; Meshkov, S.; Messenger, C.; Meyer, M. S.; Miao, H.; Michel, C.; Milano, L.; Miller, J.; Minenkov, Y.; Mitrofanov, V. P.; Mitselmakher, G.; Mittleman, R.; Miyakawa, O.; Moe, B.; Mohan, M.; Mohanty, S. D.; Mohapatra, S. R. P.; Moraru, D.; Moreno, G.; Morgado, N.; Morgia, A.; Mori, T.; Morriss, S. R.; Mosca, S.; Mossavi, K.; Mours, B.; Mow-Lowry, C. M.; Mueller, C. L.; Mueller, G.; Mukherjee, S.; Mullavey, A.; Müller-Ebhardt, H.; Munch, J.; Murphy, D.; Murray, P. G.; Mytidis, A.; Nash, T.; Naticchioni, L.; Necula, V.; Nelson, J.; Newton, G.; Nguyen, T.; Nishizawa, A.; Nitz, A.; Nocera, F.; Nolting, D.; Normandin, M. E.; Nuttall, L.; Ochsner, E.; O'Dell, J.; Oelker, E.; Ogin, G. H.; Oh, J. J.; Oh, S. H.; O'Reilly, B.; O'Shaughnessy, R.; Osthelder, C.; Ott, C. D.; Ottaway, D. J.; Ottens, R. S.; Overmier, H.; Owen, B. J.; Page, A.; Pagliaroli, G.; Palladino, L.; Palomba, C.; Pan, Y.; Pankow, C.; Paoletti, F.; Papa, M. A.; Parisi, M.; Pasqualetti, A.; Passaquieti, R.; Passuello, D.; Patel, P.; Pedraza, M.; Peiris, P.; Pekowsky, L.; Penn, S.; Perreca, A.; Persichetti, G.; Phelps, M.; Pickenpack, M.; Piergiovanni, F.; Pietka, M.; Pinard, L.; Pinto, I. M.; Pitkin, M.; Pletsch, H. J.; Plissi, M. V.; Poggiani, R.; Pöld, J.; Postiglione, F.; Prato, M.; Predoi, V.; Prestegard, T.; Price, L. R.; Prijatelj, M.; Principe, M.; Privitera, S.; Prix, R.; Prodi, G. A.; Prokhorov, L. G.; Puncken, O.; Punturo, M.; Puppo, P.; Quetschke, V.; Quitzow-James, R.; Raab, F. J.; Rabeling, D. S.; Rácz, I.; Radkins, H.; Raffai, P.; Rakhmanov, M.; Rankins, B.; Rapagnani, P.; Raymond, V.; Re, V.; Redwine, K.; Reed, C. M.; Reed, T.; Regimbau, T.; Reid, S.; Reitze, D. H.; Ricci, F.; Riesen, R.; Riles, K.; Robertson, N. A.; Robinet, F.; Robinson, C.; Robinson, E. L.; Rocchi, A.; Roddy, S.; Rodriguez, C.; Rodruck, M.; Rolland, L.; Rollins, J. G.; Romano, J. D.; Romano, R.; Romie, J. H.; Rosińska, D.; Röver, C.; Rowan, S.; Rüdiger, A.; Ruggi, P.; Ryan, K.; Sainathan, P.; Salemi, F.; Sammut, L.; Sandberg, V.; Sannibale, V.; Santamaría, L.; Santiago-Prieto, I.; Santostasi, G.; Sassolas, B.; Sathyaprakash, B. S.; Sato, S.; Saulson, P. R.; Savage, R. L.; Schilling, R.; Schnabel, R.; Schofield, R. M. S.; Schreiber, E.; Schulz, B.; Schutz, B. F.; Schwinberg, P.; Scott, J.; Scott, S. M.; Seifert, F.; Sellers, D.; Sentenac, D.; Sergeev, A.; Shaddock, D. A.; Shaltev, M.; Shapiro, B.; Shawhan, P.; Shoemaker, D. H.; Sibley, A.; Siemens, X.; Sigg, D.; Singer, A.; Singer, L.; Sintes, A. M.; Skelton, G. R.; Slagmolen, B. J. J.; Slutsky, J.; Smith, J. R.; Smith, M. R.; Smith, R. J. E.; Smith-Lefebvre, N. D.; Somiya, K.; Sorazu, B.; Soto, J.; Speirits, F. C.; Sperandio, L.; Stefszky, M.; Stein, A. J.; Stein, L. C.; Steinert, E.; Steinlechner, J.; Steinlechner, S.; Steplewski, S.; Stochino, A.; Stone, R.; Strain, K. A.; Strigin, S. E.; Stroeer, A. S.; Sturani, R.; Stuver, A. L.; Summerscales, T. Z.; Sung, M.; Susmithan, S.; Sutton, P. J.; Swinkels, B.; Tacca, M.; Taffarello, L.; Talukder, D.; Tanner, D. B.; Tarabrin, S. P.; Taylor, J. R.; Taylor, R.; Thomas, P.; Thorne, K. A.; Thorne, K. S.; Thrane, E.; Thüring, A.; Tokmakov, K. V.; Tomlinson, C.; Toncelli, A.; Tonelli, M.; Torre, O.; Torres, C.; Torrie, C. I.; Tournefier, E.; Travasso, F.; Traylor, G.; Tseng, K.; Ugolini, D.; Vahlbruch, H.; Vajente, G.; van den Brand, J. F. J.; Van Den Broeck, C.; van der Putten, S.; van Veggel, A. A.; Vass, S.; Vasuth, M.; Vaulin, R.; Vavoulidis, M.; Vecchio, A.; Vedovato, G.; Veitch, J.; Veitch, P. J.; Veltkamp, C.; Verkindt, D.; Vetrano, F.; Viceré, A.; Villar, A. E.; Vinet, J.-Y.; Vitale, S.; Vitale, S.; Vocca, H.; Vorvick, C.; Vyatchanin, S. P.; Wade, A.; Wade, L.; Wade, M.; Waldman, S. J.; Wallace, L.; Wan, Y.; Wang, M.; Wang, X.; Wang, Z.; Wanner, A.; Ward, R. L.; Was, M.; Weinert, M.; Weinstein, A. J.; Weiss, R.; Wen, L.; Wessels, P.; West, M.; Westphal, T.; Wette, K.; Whelan, J. T.; Whitcomb, S. E.; White, D. J.; Whiting, B. F.; Wilkinson, C.; Willems, P. A.; Williams, L.; Williams, R.; Willke, B.; Winkelmann, L.; Winkler, W.; Wipf, C. C.; Wiseman, A. G.; Wittel, H.; Woan, G.; Wooley, R.; Worden, J.; Yakushin, I.; Yamamoto, H.; Yamamoto, K.; Yancey, C. C.; Yang, H.; Yeaton-Massey, D.; Yoshida, S.; Yu, P.; Yvert, M.; Zadroźny, A.; Zanolin, M.; Zendri, J.-P.; Zhang, F.; Zhang, L.; Zhang, W.; Zhao, C.; Zotov, N.; Zucker, M. E.; Zweizig, J.

2012-05-01

We present the results of a weakly modeled burst search for gravitational waves from mergers of nonspinning intermediate mass black holes in the total mass range 100-450M⊙ and with the component mass ratios between 1∶1 and 4∶1. The search was conducted on data collected by the LIGO and Virgo detectors between November of 2005 and October of 2007. No plausible signals were observed by the search which constrains the astrophysical rates of the intermediate mass black holes mergers as a function of the component masses. In the most efficiently detected bin centered on 88+88M⊙, for nonspinning sources, the rate density upper limit is 0.13 per Mpc3 per Myr at the 90% confidence level.

Search for Gravitational Waves from Intermediate Mass Binary Black Holes

NASA Technical Reports Server (NTRS)

Blackburn, L.; Camp, J. B.; Cannizzo, J.; Stroeer, A. S.

2012-01-01

We present the results of a weakly modeled burst search for gravitational waves from mergers of non-spinning intermediate mass black holes (IMBH) in the total mass range 100-450 solar Mass and with the component mass ratios between 1:1 and 4:1. The search was conducted on data collected by the LIGO and Virgo detectors between November of 2005 and October of 2007. No plausible signals were observed by the search which constrains the astrophysical rates of the IMBH mergers as a function of the component masses. In the most efficiently detected bin centered on 88 + 88 solar Mass , for non-spinning sources, the rate density upper limit is 0.13 per Mpc(exp 3) per Myr at the 90% confidence level.

A technique for rapid source apportionment applied to ambient organic aerosol measurements from a thermal desorption aerosol gas chromatograph (TAG)

DOE PAGES

Zhang, Yaping; Williams, Brent J.; Goldstein, Allen H.; ...

2016-11-25

Here, we present a rapid method for apportioning the sources of atmospheric organic aerosol composition measured by gas chromatography–mass spectrometry methods. Here, we specifically apply this new analysis method to data acquired on a thermal desorption aerosol gas chromatograph (TAG) system. Gas chromatograms are divided by retention time into evenly spaced bins, within which the mass spectra are summed. A previous chromatogram binning method was introduced for the purpose of chromatogram structure deconvolution (e.g., major compound classes) (Zhang et al., 2014). Here we extend the method development for the specific purpose of determining aerosol samples' sources. Chromatogram bins are arrangedmore » into an input data matrix for positive matrix factorization (PMF), where the sample number is the row dimension and the mass-spectra-resolved eluting time intervals (bins) are the column dimension. Then two-dimensional PMF can effectively do three-dimensional factorization on the three-dimensional TAG mass spectra data. The retention time shift of the chromatogram is corrected by applying the median values of the different peaks' shifts. Bin width affects chemical resolution but does not affect PMF retrieval of the sources' time variations for low-factor solutions. A bin width smaller than the maximum retention shift among all samples requires retention time shift correction. A six-factor PMF comparison among aerosol mass spectrometry (AMS), TAG binning, and conventional TAG compound integration methods shows that the TAG binning method performs similarly to the integration method. However, the new binning method incorporates the entirety of the data set and requires significantly less pre-processing of the data than conventional single compound identification and integration. In addition, while a fraction of the most oxygenated aerosol does not elute through an underivatized TAG analysis, the TAG binning method does have the ability to achieve molecular level resolution on other bulk aerosol components commonly observed by the AMS.« less

A technique for rapid source apportionment applied to ambient organic aerosol measurements from a thermal desorption aerosol gas chromatograph (TAG)

NASA Astrophysics Data System (ADS)

Zhang, Yaping; Williams, Brent J.; Goldstein, Allen H.; Docherty, Kenneth S.; Jimenez, Jose L.

2016-11-01

We present a rapid method for apportioning the sources of atmospheric organic aerosol composition measured by gas chromatography-mass spectrometry methods. Here, we specifically apply this new analysis method to data acquired on a thermal desorption aerosol gas chromatograph (TAG) system. Gas chromatograms are divided by retention time into evenly spaced bins, within which the mass spectra are summed. A previous chromatogram binning method was introduced for the purpose of chromatogram structure deconvolution (e.g., major compound classes) (Zhang et al., 2014). Here we extend the method development for the specific purpose of determining aerosol samples' sources. Chromatogram bins are arranged into an input data matrix for positive matrix factorization (PMF), where the sample number is the row dimension and the mass-spectra-resolved eluting time intervals (bins) are the column dimension. Then two-dimensional PMF can effectively do three-dimensional factorization on the three-dimensional TAG mass spectra data. The retention time shift of the chromatogram is corrected by applying the median values of the different peaks' shifts. Bin width affects chemical resolution but does not affect PMF retrieval of the sources' time variations for low-factor solutions. A bin width smaller than the maximum retention shift among all samples requires retention time shift correction. A six-factor PMF comparison among aerosol mass spectrometry (AMS), TAG binning, and conventional TAG compound integration methods shows that the TAG binning method performs similarly to the integration method. However, the new binning method incorporates the entirety of the data set and requires significantly less pre-processing of the data than conventional single compound identification and integration. In addition, while a fraction of the most oxygenated aerosol does not elute through an underivatized TAG analysis, the TAG binning method does have the ability to achieve molecular level resolution on other bulk aerosol components commonly observed by the AMS.

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

Bacterio-electric leaching of metals

DOEpatents

Lazaroff, Norman; Dugan, Patrick R.

1992-07-07

The separation of cationic materials from an ore body is assisted by the application of an electric potential, and resulting current, to the ore body, in association with iron or sulphur oxidizing bacteria. The combined process induces migration of cationic metals to a cathode suspended within the ore body so that the cationic metal can be preferentially separated from the ore body.

Bacterio-electric leaching of metals

DOEpatents

Lazaroff, Norman; Dugan, Patrick R.

1992-01-01

The separation of cationic materials from an ore body is assisted by the application of an electric potential, and resulting current, to the ore body, in association with iron or sulphur oxidizing bacteria. The combined process induces migration of cationic metals to a cathode suspended within the ore body so that the cationic metal can be preferentially separated from the ore body.

De novo phasing with X-ray laser reveals mosquito larvicide BinAB structure [A potent binary mosquito larvicide revealed by de novo phasing with an X-ray free-electron laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colletier, Jacques -Philippe; Sawaya, Michael R.; Gingery, Mari

BinAB is a naturally occurring paracrystalline larvicide distributed worldwide to combat the devastating diseases borne by mosquitoes. These crystals are composed of homologous molecules, BinA and BinB, which play distinct roles in the multi-step intoxication process, transforming from harmless, robust crystals, to soluble protoxin heterodimers, to internalized mature toxin, and finally to toxic oligomeric pores. The small size of the crystals—50 unit cells per edge, on average—has impeded structural characterization by conventional means. Here we report the structure of Lysinibacillus sphaericus BinAB solved de novo by serial-femtosecond crystallography at an X-ray free-electron laser. The structure reveals tyrosine- and carboxylate-mediated contactsmore » acting as pH switches to release soluble protoxin in the alkaline larval midgut. An enormous heterodimeric interface appears to be responsible for anchoring BinA to receptor-bound BinB for co-internalization. Furthermore, this interface is largely composed of propeptides, suggesting that proteolytic maturation would trigger dissociation of the heterodimer and progression to pore formation.« less

De novo phasing with X-ray laser reveals mosquito larvicide BinAB structure [A potent binary mosquito larvicide revealed by de novo phasing with an X-ray free-electron laser

DOE PAGES

Colletier, Jacques -Philippe; Sawaya, Michael R.; Gingery, Mari; ...

2016-09-28

BinAB is a naturally occurring paracrystalline larvicide distributed worldwide to combat the devastating diseases borne by mosquitoes. These crystals are composed of homologous molecules, BinA and BinB, which play distinct roles in the multi-step intoxication process, transforming from harmless, robust crystals, to soluble protoxin heterodimers, to internalized mature toxin, and finally to toxic oligomeric pores. The small size of the crystals—50 unit cells per edge, on average—has impeded structural characterization by conventional means. Here we report the structure of Lysinibacillus sphaericus BinAB solved de novo by serial-femtosecond crystallography at an X-ray free-electron laser. The structure reveals tyrosine- and carboxylate-mediated contactsmore » acting as pH switches to release soluble protoxin in the alkaline larval midgut. An enormous heterodimeric interface appears to be responsible for anchoring BinA to receptor-bound BinB for co-internalization. Furthermore, this interface is largely composed of propeptides, suggesting that proteolytic maturation would trigger dissociation of the heterodimer and progression to pore formation.« less

Upper ocean moored current and density profiler applied to winter conditions near Bermuda

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eriksen, C.C.; Dahlen, J.M.; Shillingford, J.T. Jr.

1982-09-20

A new moored instrument which makes repeated high vertical resolution profiles of current, temperature, and salinity in the upper ocean over extended periods was used to observe midwinter conditions near Bermuda. The operation and performance of the instrument, called the profiling current meter (PCM), in the surface wave environment of winter storms is reported here. The PCM profiles along the upper portion of a slightly subsurface mooring by adjusting its buoyancy under computer control. This design decouples the instrument from vertical motions of the mooring induced by surface waves, so that its electromagnetic current sensor operates in a favorable mean-to-fluctuatingmore » flow regime. Current, temperature, and electrical conductivity are (vector) averaged into contiguous preselected bins several meters wide over the possible profile range of 20- to 250-m depth. The PCM is capable of collecting 1000--4000 profiles in a 6- to 12-month period, depending on depth range and ambient currents. A variety of baroclinic motions are evident in the Bermuda observations. Upper ocean manifestations of both Kelvin and superinertial island-trapped waves dominate longshore currents. Vertical coherence of onshore current and temperature suggest that internal wave vertical wave number energy distribution is independent of frequency but modified by island bathymetry. Kinetic energy in shear integrated over a 115.6-m-thick layer in the upper ocean is limited to values less than or equal to the potential energy required to mix the existing stratification. Mixing events occur when kinetic energy associated with shear drives the bulk Richardson number (defined by the ratio of energy integrals over the range profiles) to unity, where it remains while shear and stratification disappear together.« less

A Total Ozone Dependent Ozone Profile Climatology Based on Ozone-Sondes and Aura MLS Data

NASA Astrophysics Data System (ADS)

Labow, G. J.; McPeters, R. D.; Ziemke, J. R.

2014-12-01

A new total ozone-based ozone profile climatology has been created for use in satellite and/or ground based ozone retrievals. This climatology was formed by combining data from the Microwave Limb Sounder (MLS) with data from balloon sondes and binned by zone and total ozone. Because profile shape varies with total column ozone, this climatology better captures the ozone variations than the previously used seasonal climatologies, especially near the tropopause. This is significantly different than ozone climatologies used in the past as there is no time component. The MLS instrument on Aura has excellent latitude coverage and measures ozone profiles daily from the upper troposphere to the lower mesosphere at ~3.5 km resolution. Almost a million individual MLS ozone measurements are merged with data from over 55,000 ozonesondes which are then binned as a function of total ozone. The climatology consists of average ozone profiles as a function of total ozone for six 30 degree latitude bands covering altitudes from 0-75 km (in Z* pressure altitude coordinates). This new climatology better represents the profile shape as a function of total ozone than previous climatologies and shows some remarkable and somewhat unexpected correlations between total ozone and ozone in the lower altitudes, particularly in the lower and middle troposphere. These data can also be used to infer biases and errors in either the MLS retrievals or ozone sondes.

Detection of cosmic microwave background structure in a second field with the Cosmic Anisotropy Telescope

NASA Astrophysics Data System (ADS)

Baker, Joanne C.; Grainge, Keith; Hobson, M. P.; Jones, Michael E.; Kneissl, R.; Lasenby, A. N.; O'Sullivan, C. M. M.; Pooley, Guy; Rocha, G.; Saunders, Richard; Scott, P. F.; Waldram, E. M.

1999-10-01

We describe observations at frequencies near 15GHz of the second 2x2deg^2 field imaged with the Cambridge Cosmic Anisotropy Telescope (CAT). After the removal of discrete radio sources, structure is detected in the images on characteristic scales of about half a degree, corresponding to spherical harmonic multipoles in the range l~330-680. A Bayesian analysis confirms that the signal arises predominantly from the cosmic microwave background (CMB) radiation for multipoles in the lower half of this range; the average broad-band power in a bin with centroid l=422 (θ~51arcmin) is estimated to be ΔTT 2.1-0.5+0.4 x10-5. For multipoles centred on l=615 (θ~35arcmin), we find contamination from Galactic emission is significant, and constrain the CMB contribution to the measured power in this bin to be ΔTT<2.0x10^-5 (1σ upper limit). These new results are consistent with the first detection made by CAT in a completely different area of sky. Together with data from other experiments, this new CAT detection adds weight to earlier evidence from CAT for a downturn in the CMB power spectrum on scales smaller than 1deg. Improved limits on the values of H0 and Ω are determined using the new CAT data.

The cyclic-di-GMP phosphodiesterase BinA negatively regulates cellulose-containing biofilms in Vibrio fischeri.

PubMed

Bassis, Christine M; Visick, Karen L

2010-03-01

Bacteria produce different types of biofilms under distinct environmental conditions. Vibrio fischeri has the capacity to produce at least two distinct types of biofilms, one that relies on the symbiosis polysaccharide Syp and another that depends upon cellulose. A key regulator of biofilm formation in bacteria is the intracellular signaling molecule cyclic diguanylate (c-di-GMP). In this study, we focused on a predicted c-di-GMP phosphodiesterase encoded by the gene binA, located directly downstream of syp, a cluster of 18 genes critical for biofilm formation and the initiation of symbiotic colonization of the squid Euprymna scolopes. Disruption or deletion of binA increased biofilm formation in culture and led to increased binding of Congo red and calcofluor, which are indicators of cellulose production. Using random transposon mutagenesis, we determined that the phenotypes of the DeltabinA mutant strain could be disrupted by insertions in genes in the bacterial cellulose biosynthesis cluster (bcs), suggesting that cellulose production is negatively regulated by BinA. Replacement of critical amino acids within the conserved EAL residues of the EAL domain disrupted BinA activity, and deletion of binA increased c-di-GMP levels in the cell. Together, these data support the hypotheses that BinA functions as a phosphodiesterase and that c-di-GMP activates cellulose biosynthesis. Finally, overexpression of the syp regulator sypG induced binA expression. Thus, this work reveals a mechanism by which V. fischeri inhibits cellulose-dependent biofilm formation and suggests that the production of two different polysaccharides may be coordinated through the action of the cellulose inhibitor BinA.

Sensitivity of a Cloud-Resolving Model to the Bulk and Explicit Bin Microphysical Schemes. Part 1; Validations with a PRE-STORM Case

NASA Technical Reports Server (NTRS)

Li, Xiao-Wen; Tao, Wei-Kuo; Khain, Alexander P.; Simpson, Joanne; Johnson, Daniel E.

2004-01-01

A cloud-resolving model is used to study sensitivities of two different microphysical schemes, one is the bulk type, and the other is an explicit bin scheme, in simulating a mid-latitude squall line case (PRE-STORM, June 10-11, 1985). Simulations using different microphysical schemes are compared with each other and also with the observations. Both the bulk and bin models reproduce the general features during the developing and mature stage of the system. The leading convective zone, the trailing stratiform region, the horizontal wind flow patterns, pressure perturbation associated with the storm dynamics, and the cool pool in front of the system all agree well with the observations. Both the observations and the bulk scheme simulation serve as validations for the newly incorporated bin scheme. However, it is also shown that, the bulk and bin simulations have distinct differences, most notably in the stratiform region. Weak convective cells exist in the stratiform region in the bulk simulation, but not in the bin simulation. These weak convective cells in the stratiform region are remnants of the previous stronger convections at the leading edge of the system. The bin simulation, on the other hand, has a horizontally homogeneous stratiform cloud structure, which agrees better with the observations. Preliminary examinations of the downdraft core strength, the potential temperature perturbation, and the evaporative cooling rate show that the differences between the bulk and bin models are due mainly to the stronger low-level evaporative cooling in convective zone simulated in the bulk model. Further quantitative analysis and sensitivity tests for this case using both the bulk and bin models will be presented in a companion paper.

Search for a standard model-like Higgs boson in the μ^+μ^- and e^+e^- decay channels at the LHC

DOE PAGES

Khachatryan, Vardan

2015-03-26

A search is presented for a standard model-like Higgs boson decaying to the μ +μ - ore +e - final states based on proton–proton collisions recorded by the CMS experiment at the CERN LHC. The data correspond to integrated luminosities of 5.0 fb -1 at a centre-of-mass energy of 7 TeV and 19.7 fb -1 at 8 TeV for the μ +μ - search, and of 19.7 fb -1 at 8 TeV for the e +e - search. Upper limits on the production cross section times branching fraction at the 95% confidence level are reported for Higgs boson masses inmore » the range from 120 to 150 GeV. For a Higgs boson with a mass of 125 GeV decaying to μ +μ -, the observed (expected) upper limit on the production rate is found to be 7.4 ( ) times the standard model value. This corresponds to an upper limit on the branching fraction of 0.0016. Similarly, for e +e -, an upper limit of 0.0019 is placed on the branching fraction, which is ≈3.7×105 times the standard model value. These results, together with recent evidence of the 125 GeV boson coupling to τ-leptons with a larger branching fraction consistent with the standard model, confirm that the leptonic couplings of the new boson are not flavour-universal.« less

Explosibility of Metal Powders

DTIC Science & Technology

1964-01-01

299 1832 - Copper ore, sulfide , Mexic.................................................- - 100 - - - 300 1873 - Iron ore, magnetite...100 - - - 302 2076.............................................. do...................................... - - 100 - - - 303 749 - Iron ore, sulfide ...9 Pyrophoricity ............................................................... 9 Prevention of ignition and explosion

Use of mesophilic and thermophilic bacteria for the improvement of copper extraction from a low-grade ore

NASA Astrophysics Data System (ADS)

Darezereshki, E.; Schaffie, M.; Lotfalian, M.; Seiedbaghery, S. A.; Ranjbar, M.

2011-04-01

Bioleaching was examined for copper extraction from a low grade ore using mesophilic and moderate thermophilic bacteria. Five equal size columns were used for the leaching of the ore. Sulfuric acid solution with a flow rate of 3.12 L·m-2·h-1 and pH 1.5 passed through each column continuously for 90 d. In the first and the second column, bioleaching was performed without agglomeration of the ore and on the agglomerated ore, respectively. 28wt% of the copper was extracted in the first column after 40 d, while this figure was 38wt% in the second column. After 90 d, however, the overall extractions were almost the same for both of them. Bioleaching with mesophilic bacteria was performed in the third column without agglomeration of the ore and in the fourth column on the agglomerated ore. After 40 d, copper extractions in the third and the fourth columns were 62wt% and 70wt%, respectively. Copper extractions were 75wt% for both the columns after 90 d. For the last column, bioleaching was performed with moderate thermophilic bacteria and agglomerated ore. Copper extractions were 80wt% and 85wt% after 40 and 90 d, respectively. It was concluded that crushing and agglomeration of the ore using bacteria could enhance the copper extraction considerably.

Occupational and environmental mercury exposure among small-scale gold miners in the Talensi-Nabdam District of Ghana’s Upper East region

PubMed Central

Paruchuri, Yasaswi; Siuniak, Amanda; Johnson, Nicole; Levin, Elena; Mitchell, Katherine; Goodrich, Jaclyn M.; Renne, Elisha P.; Basu, Niladri

2014-01-01

Mercury use in small-scale gold mining is ubiquitous across Ghana but little is known about the extent to which such activities have contaminated community residents and miners. Here, occupational exposures to elemental mercury (via urine sampling) and dietary exposures to methylmercury (via hair sampling) were assessed among 120 participants recruited from a mining community located in the Talensi-Nabdam District of Ghana’s Upper East region during summer 2009. More than one-fifth of the participants had moderately high levels of urinary mercury (>10 µg/L) and 5% had urine mercury levels that exceeded the WHO guideline value of 50 µg/L. When participants were stratified according to occupation, those active in the mining industry had the highest mercury levels. Specifically, individuals that burned amalgam had urine mercury levels (median: 43.8 µg/L; mean ± SD: 171.1 ± 296.5 µg/L; n=5) significantly higher than median values measured in mechanical operators (11.6 µg/L, n=4), concession managers/owners (5.6 µg/L, n=11), excavators that blast and chisel ore (4.9 µg/L, n=33), individuals that sift and grind crushed ore (2.2 µg/L, n=47), support workers (0.5 µg/L, n=14), and those with no role in the mining sector (2.5 µg/L, n=6). There was a significant positive spearman correlation between fish consumption and hair mercury levels (r = 0.30) but not with urine mercury (r = 0.18) though further studies are needed to document which types of fish are consumed as well as portion sizes. Given that 200,000 people in Ghana are involved in the small-scale gold mining industry and that the numbers are expected to grow in Ghana and many other regions of the world, elucidating mercury exposure pathways in such communities is important to help shape policies and behaviors that may minimize health risks. PMID:20875913

The lithosphere architecture and geodynamic of the Middle and Lower Yangtze metallogenic belt in eastern China: constraints from integrated geophysical data

NASA Astrophysics Data System (ADS)

Lü, Qingtian; Shi, Danian; Jiang, Guoming; Dong, Shuwen

2014-05-01

The lithosphere structure and deep processes are keys to understanding mineral system and ore-forming processes. Lithosphere-scale process could create big footprints or signatures which can be observed by geophysics methods. SinoProbe has conducted an integrated deep exploration across middle and lower reaches of Yangtze Metallogenic Belt (YMB) in Eastern China, these included broadband seismic, reflection seismic, wide-angle reflection and magnetotellurics survey. Seismic reflection profiles and MT survey were also performed in Luzong, Tongling and Ningwu ore districts to construct 3D geological model. The resulting geophysical data provides new information which help to better understanding the lithosphere structure, geodynamic, deformation and heat and mass transportation that lead to the formation of the Metallogenic Belt. The major results are: (1) Lower velocity body at the top of upper mantle and a SE dipping high velocity body were imaged by teleseismic tomography beneath YMB; (2) Shear wave splitting results show NE parallel fast-wave polarization direction which parallel with tectonic lineament; (3) The reflection seismic data support the crustal-detachment model, the lower and upper crust was detached during contraction deformation near Tanlu fault and Ningwu volcanic basin; (4) Broadband and reflection seismic confirm the shallow Moho beneath YMB; (5) Strong correlation of lower crust reflectivity with magmatism; (6) The lower crust below Luzong Volcanics shows obvious reflective anisotropy both at the crust-mantle transition and the brittle-ductile transition in the crust. All these features suggest that introcontinental subduction, lithosphere delamination, mantle sources magmatic underplating, and MASH process are responsible for the formation of this Mesozoic metallogenic belt. Acknowledgment: We acknowledge the financial support of SinoProbe by the Ministry of Finance and Ministry of Land and Resources, P. R. China, under Grant sinoprobe-03, and financial support by National Natural Science Foundation of China under Grant 40930418

Quantifying uranium transport rates and storage of fluvially eroded mine tailings from a historic mine site in the Grand Canyon Region

NASA Astrophysics Data System (ADS)

Skalak, K.; Benthem, A. J.; Walton-Day, K. E.; Jolly, G.

2015-12-01

The Grand Canyon region contains a large number of breccia pipes with economically viable uranium, copper, and silver concentrations. Mining in this region has occurred since the late 19th century and has produced ore and waste rock having elevated levels of uranium and other contaminants. Fluvial transport of these contaminants from mine sites is a possibility, as this arid region is susceptible to violent storms and flash flooding which might erode and mobilize ore or waste rock. In order to assess and manage the risks associated with uranium mining, it is important to understand the transport and storage rates of sediment and uranium within the ephemeral streams of this region. We are developing a 1-dimensional sediment transportation model to examine uranium transport and storage through a typical canyon system in this region. Our study site is Hack Canyon Mine, a uranium and copper mine site, which operated in the 1980's and is currently experiencing fluvial erosion of its waste rock repository. The mine is located approximately 40km upstream from the Colorado River and is in a deep, narrow canyon with a small watershed. The stream is ephemeral for the upper half of its length and sediment is primarily mobilized during flash flood events. We collected sediment samples at 110 locations longitudinally through the river system to examine the distribution of uranium in the stream. Samples were sieved to the sand size and below fraction (<2mm) and uranium was measured by gamma-ray spectroscopy. Sediment storage zones were also examined in the upper 8km of the system to determine where uranium is preferentially stored in canyon systems. This information will quantify the downstream transport of constituents associated with the Hack Canyon waste rock and contribute to understanding the risks associated with fluvial mobilization of uranium mine waste.

Bauxite and Kaolin Deposits of the Irwinton district, Georgia

USGS Publications Warehouse

Lang, Walter B.; Warren, Walter C.; Thompson, Raymond M.; Overstreet, Elizabeth F.

1965-01-01

The Irwinton district is in the central part of Georgia at the inner margin of the Coastal Plain province. The oldest rocks exposed in the district are crystalline rocks of the Piedmont province. They are unconformably overlain by nonmarine sedimentary strata of Late Cretaceous age, including gravel, micaceous sand, and lenses of kaolin. Bauxite has been found in a few of the kaolin lenses near the top of the sequence of these strata. During a long period prior to deposition of the over- lying marine beds of the Claiborne and Jackson Groups (middle and upper Eocene), the Upper Cretaceous strata were subjected to subaerial erosion. The bauxite deposits are considered to have formed during this period. They range in thickness from a few inches to more than 10 feet and occupy areas ranging from a few square feet to more than 5 acres. Most of the known bauxite deposits lie along the valleys of Commissioners Creek and Big Sandy Creek in Wilkinson County. The kaolin lenses are much larger than the bauxite deposits; some of the lenses underlie more than 200 acres and are more than 20 feet thick. Bauxite was discovered in the district in 1907 and was mined from 1910 to 1928. A few additional carloads of ore were shipped in 1941 and 1942, but no ore has been mined since that time. Reserves of high-grade bauxite are very small. Reserves of all grades of bauxite plus bauxitic clay may be about 400,000 long tons. The Irwinton district is the principal source of high-grade kaolin in the United States. The presence of kaolin here has been known since early colo- nial time, and it has been mined continuously since 1897. Production in 1959 was 1,940,279 short tons. The reserves of kaolin are very large but have never been adequately measured. Reserves of first and second grade kaolin may be 67 to 84 million short tons. Kaolin of lower grade is present in larger quantity.

Whole-body Vibration Exposure of Drill Operators in Iron Ore Mines and Role of Machine-Related, Individual, and Rock-Related Factors.

PubMed

Chaudhary, Dhanjee Kumar; Bhattacherjee, Ashis; Patra, Aditya Kumar; Chau, Nearkasen

2015-12-01

This study aimed to assess the whole-body vibration (WBV) exposure among large blast hole drill machine operators with regard to the International Organization for Standardization (ISO) recommended threshold values and its association with machine- and rock-related factors and workers' individual characteristics. The study population included 28 drill machine operators who had worked in four opencast iron ore mines in eastern India. The study protocol comprised the following: measurements of WBV exposure [frequency weighted root mean square (RMS) acceleration (m/s(2))], machine-related data (manufacturer of machine, age of machine, seat height, thickness, and rest height) collected from mine management offices, measurements of rock hardness, uniaxial compressive strength and density, and workers' characteristics via face-to-face interviews. More than 90% of the operators were exposed to a higher level WBV than the ISO upper limit and only 3.6% between the lower and upper limits, mainly in the vertical axis. Bivariate correlations revealed that potential predictors of total WBV exposure were: machine manufacturer (r = 0.453, p = 0.015), age of drill (r = 0.533, p = 0.003), and hardness of rock (r = 0.561, p = 0.002). The stepwise multiple regression model revealed that the potential predictors are age of operator (regression coefficient β = -0.052, standard error SE = 0.023), manufacturer (β = 1.093, SE = 0.227), rock hardness (β = 0.045, SE = 0.018), uniaxial compressive strength (β = 0.027, SE = 0.009), and density (β = -1.135, SE = 0.235). Prevention should include using appropriate machines to handle rock hardness, rock uniaxial compressive strength and density, and seat improvement using ergonomic approaches such as including a suspension system.

Review of rare earth element concentrations in oil shales of the Eocene Green River Formation

USGS Publications Warehouse

Birdwell, Justin E.

2012-01-01

Concentrations of the lanthanide series or rare earth elements and yttrium were determined for lacustrine oil shale samples from the Eocene Green River Formation in the Piceance Basin of Colorado and the Uinta Basin of Utah. Unprocessed oil shale, post-pyrolysis (spent) shale, and leached shale samples were examined to determine if oil-shale processing to generate oil or the remediation of retorted shale affects rare earth element concentrations. Results for unprocessed Green River oil shale samples were compared to data published in the literature on reference materials, such as chondritic meteorites, the North American shale composite, marine oil shale samples from two sites in northern Tibet, and mined rare earth element ores from the United States and China. The Green River oil shales had lower rare earth element concentrations (66.3 to 141.3 micrograms per gram, μg g-1) than are typical of material in the upper crust (approximately 170 μg g-1) and were also lower in rare earth elements relative to the North American shale composite (approximately 165 μg g-1). Adjusting for dilution of rare earth elements by organic matter does not account for the total difference between the oil shales and other crustal rocks. Europium anomalies for Green River oil shales from the Piceance Basin were slightly lower than those reported for the North American shale composite and upper crust. When compared to ores currently mined for rare earth elements, the concentrations in Green River oil shales are several orders of magnitude lower. Retorting Green River oil shales led to a slight enrichment of rare earth elements due to removal of organic matter. When concentrations in spent and leached samples were normalized to an original rock basis, concentrations were comparable to those of the raw shale, indicating that rare earth elements are conserved in processed oil shales.

Whole-body Vibration Exposure of Drill Operators in Iron Ore Mines and Role of Machine-Related, Individual, and Rock-Related Factors

PubMed Central

Chaudhary, Dhanjee Kumar; Bhattacherjee, Ashis; Patra, Aditya Kumar; Chau, Nearkasen

2015-01-01

Background This study aimed to assess the whole-body vibration (WBV) exposure among large blast hole drill machine operators with regard to the International Organization for Standardization (ISO) recommended threshold values and its association with machine- and rock-related factors and workers' individual characteristics. Methods The study population included 28 drill machine operators who had worked in four opencast iron ore mines in eastern India. The study protocol comprised the following: measurements of WBV exposure [frequency weighted root mean square (RMS) acceleration (m/s2)], machine-related data (manufacturer of machine, age of machine, seat height, thickness, and rest height) collected from mine management offices, measurements of rock hardness, uniaxial compressive strength and density, and workers' characteristics via face-to-face interviews. Results More than 90% of the operators were exposed to a higher level WBV than the ISO upper limit and only 3.6% between the lower and upper limits, mainly in the vertical axis. Bivariate correlations revealed that potential predictors of total WBV exposure were: machine manufacturer (r = 0.453, p = 0.015), age of drill (r = 0.533, p = 0.003), and hardness of rock (r = 0.561, p = 0.002). The stepwise multiple regression model revealed that the potential predictors are age of operator (regression coefficient β = −0.052, standard error SE = 0.023), manufacturer (β = 1.093, SE = 0.227), rock hardness (β = 0.045, SE = 0.018), uniaxial compressive strength (β = 0.027, SE = 0.009), and density (β = –1.135, SE = 0.235). Conclusion Prevention should include using appropriate machines to handle rock hardness, rock uniaxial compressive strength and density, and seat improvement using ergonomic approaches such as including a suspension system. PMID:26929838

14. Interior view, grain tanks (bins). Barrel view of tunnel ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. Interior view, grain tanks (bins). Barrel view of tunnel for load-out belt conveyor system located below tanks. Square, numbered spouts gravity-feed grain from overhead bins onto belt. - Saint Anthony Elevator No. 3, 620 Malcom Avenue, Southeast, Minneapolis, Hennepin County, MN

Spectral CT Reconstruction with Image Sparsity and Spectral Mean

PubMed Central

Zhang, Yi; Xi, Yan; Yang, Qingsong; Cong, Wenxiang; Zhou, Jiliu

2017-01-01

Photon-counting detectors can acquire x-ray intensity data in different energy bins. The signal to noise ratio of resultant raw data in each energy bin is generally low due to the narrow bin width and quantum noise. To address this problem, here we propose an image reconstruction approach for spectral CT to simultaneously reconstructs x-ray attenuation coefficients in all the energy bins. Because the measured spectral data are highly correlated among the x-ray energy bins, the intra-image sparsity and inter-image similarity are important prior acknowledge for image reconstruction. Inspired by this observation, the total variation (TV) and spectral mean (SM) measures are combined to improve the quality of reconstructed images. For this purpose, a linear mapping function is used to minimalize image differences between energy bins. The split Bregman technique is applied to perform image reconstruction. Our numerical and experimental results show that the proposed algorithms outperform competing iterative algorithms in this context. PMID:29034267

26 CFR 1.272-1 - Expenditures relating to disposal of coal or domestic iron ore.

Code of Federal Regulations, 2013 CFR

2013-04-01

... domestic iron ore. 1.272-1 Section 1.272-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE... Expenditures relating to disposal of coal or domestic iron ore. (a) Introduction. Section 272 provides special... sometimes referred to as a “coal royalty contract” or “iron ore royalty contract”) for the disposal of coal...

26 CFR 1.272-1 - Expenditures relating to disposal of coal or domestic iron ore.

Code of Federal Regulations, 2011 CFR

2011-04-01

... domestic iron ore. 1.272-1 Section 1.272-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE... Expenditures relating to disposal of coal or domestic iron ore. (a) Introduction. Section 272 provides special... sometimes referred to as a “coal royalty contract” or “iron ore royalty contract”) for the disposal of coal...

IMPACT: How ORE Findings Have Affected Decisions in Austin and Beyond.

ERIC Educational Resources Information Center

Wilkinson, David, Ed.; Ligon, Glynn, Ed.

Over the years, findings of the Office of Research and Evaluation (ORE) of the Austin (Texas) Independent School District (AISD) have had a significant impact on decisions made in the district and sometimes beyond it. The ORE's impact in the AISD is reviewed in 16 areas. Some of the major findings are summarized: (1) ORE studies of retention in…

75 FR 68788 - Ore Knob Mine Superfund Site; Jefferson, Ashe County, North Carolina; Notice of Settlement

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-09

... ENVIRONMENTAL PROTECTION AGENCY [Docket EPA-RO4-SFUND-2010-0893, FRL-9223-8] Ore Knob Mine... Agency has entered into a settlement for reimbursement of past response costs concerning the Ore Knobe..., identified by Docket ID No. EPA-RO4- SFUND-2010-0893 or Site name Ore Knob Mine Superfund Site by one of the...

Microwave enhanced recovery of nickel-copper ore: communition and floatability aspects.

PubMed

Henda, R; Hermas, A; Gedye, R; Islam, M R

2005-01-01

A study describing the effect of microwave radiation, at a frequency of 2450 MHz, on the processes of communication and flotation of a complex sulphide nickel-copper ore is presented. Ore communication has been investigated under standard radiation-free conditions and after ore treatment in a radiated environment as a function of ore size, exposure time to radiation, and microwave power. The findings show that communication is tremendously improved by microwave radiation with values of the relative work index as low as 23% at a microwave power of 1.406 kW and after 10 s of exposure time. Communication is affected by exposure time and microwave power in a nontrivial manner. In terms of ore floatability, the experimental tests have been carried out on a sample of 75 microm in size under different exposure times. The results show that both ore concentrate recoveries and grades of nickel and copper are significantly enhanced after microwave treatment of the ore with relative increases in recovered concentrate, grade of nickel, and grade of copper of 26 wt%, 15 wt%, and 27%, respectively, at a microwave power of 1330 kW and after 30 s of exposure time.

Selective Removal of Iron from Low-Grade Ti Ore by Reacting with Calcium Chloride

NASA Astrophysics Data System (ADS)

Kang, Jungshin; Okabe, Toru H.

2017-02-01

Recently, titanium metal production by molten salt electrolysis using CaCl2 as molten salt and TiO2 or rutile (94 to 96 pct TiO2) as feedstock has been drawing attention. However, when a low-grade Ti ore (mainly FeTiO3) is used as feedstock, removal of iron (Fe) from the ore is indispensable. In this study, the influence of reaction temperature, reaction time, particle size of the ore, and source country for the ore on the removal of iron by selective chlorination using CaCl2 was assessed. Experimental results showed that the mass percent of iron in the ore decreased from 49.7 to 1.79 pct under certain conditions by selective removal of iron as FeCl2. As a result, high-grade CaTiO3 was produced when the ore particles smaller than 74 µm reacted with CaCl2 at 1240 K (967 °C) for 8 to 10 hours. Therefore, this study demonstrates that the removal of iron from the ore is feasible through the selective chlorination process using CaCl2 by optimizing the variables.

Remote sensing strategic exploration of large or superlarge gold ore deposits

NASA Astrophysics Data System (ADS)

Yan, Shouxun; Liu, Qingsheng; Wang, Hongmei; Wang, Zhigang; Liu, Suhong

1998-08-01

To prospect large or superlarge gold ore deposits, blending of remote sensing techniques and modern metallogenitic theories is one of the effective measures. The theory of metallogeny plays a director role before and during remote sensing technique applications. The remote sensing data with different platforms and different resolutions can be respectively applied to detect direct or indirect metallogenic information, and to identify the ore-controlling structure, especially, the ore-controlling structural assemblage, which, conversely, usually are the new conditions to study and to modify the metallogenic model, and to further develop the exploration model of large or superlarge ore deposits. Guidance by an academic idea of 'adjustment structure' which is the conceptual model of transverse structure, an obscured ore- controlling transverse structure has been identified on the refined TM imagery in the Hadamengou gold ore deposit, Setai Hyperspectral Geological Remote Sensing Testing Site (SHGRSTS), Wulashan mountains, Inner Mongolia, China. Meanwhile, The MAIS data has been applied to quickly identify the auriferous alteration rocks with Correspondence Analysis method and Spectral Angle Mapping (SAM) technique. The theoretical system and technical method of remote sensing strategic exploration of large or superlarge gold ore deposits have been demonstrated by the practices in the SHGRSTS.

The North American iron ore industry: a decade into the 21st century

USGS Publications Warehouse

Jorgenson, John D.; Perez, A. A

2011-01-01

During the 20th century, the iron ore mining industries of Canada and the United States passed through periods of transformation. The beginning of the 21st century has seen another period of transformation, with the failure of a number of steel companies and with consolidation of control within the North American iron ore industry. Canadian and United States iron ore production and the market control structure involved are changing rapidly. Consolidation of ownership, formation of foreign joint ventures, divestitures of upstream activities by steelmakers, and industry changes to ensure availability of feedstocks all played a role in recent developments in the North American iron ore industry. Canadian and U.S. iron ore operations and their strong linkage to downstream production, although isolated, must also be considered within the context of the changing global economy. Projects using new technology to produce direct reduced iron nuggets of 96-98% iron content and other projects designed to produce steel at minesites may once again change the face of the iron ore industry. Social and environmental issues related to sustainable development have had a significant effect on the North American iron ore industry.

Exenatide once weekly versus daily basal insulin as add-on treatment to metformin with or without a sulfonylurea: a retrospective pooled analysis in patients with poor glycemic control.

PubMed

Grimm, Michael; Li, Yan; Brunell, Steven C; Blase, Erich

2013-09-01

Basal insulin (b-INS) is typically the add-on treatment of choice for patients with poor glycemic control (ie, glycated hemoglobin [HbA1c] level ≥ 8.5%), but it is unclear whether b-INS is the best option. In this post hoc analysis, the efficacy and tolerability of exenatide once weekly (EQW) were compared with those of b-INS in patients with type 2 diabetes mellitus and a baseline HbA1c level 8.5% who were undergoing treatment with metformin ± a sulfonylurea. Data were pooled from two 26-week, randomized, controlled trials (EQW vs insulin glargine and EQW vs insulin detemir [EQW, N = 137; b-INS, N = 126]). Treatment with either EQW or b-INS for 26 weeks was associated with significant improvements in HbA1c level compared with baseline, although patients treated with EQW experienced a significantly greater decrease in HbA1c level than those treated with b-INS (least squares [LS] mean ± SE: -2.0% ± 0.08% vs -1.6% ± 0.08%; P = 0.0008). Treatment with EQW was associated with a weight loss of 2.4 kg ± 0.23 kg (LS mean ± SE), whereas treatment with b-INS was associated with a weight gain of 2.0 kg ± 0.24 kg (LS mean difference between groups, -4.4 kg ± 0.33; P < 0.0001). Patients in the EQW group were significantly more likely to achieve the composite endpoint of an HbA1c level < 7.0%, no weight gain, and no hypoglycemic events (defined as a blood glucose level < 54 mg/dL requiring self-treatment or assistance to resolve) than patients in the b-INS group (33.6% vs 3.2%; P < 0.0001). The exposure-adjusted hypoglycemic event rates were 0.08 and 0.37 events per patient-year in the EQW and b-INS groups, respectively. Gastrointestinal adverse events occurred at a higher rate in patients who underwent EQW treatment than those who were treated with b-INS. These results show that EQW treatment was associated with significantly greater improvement in HbA1c level compared with b-INS treatment among patients with poor glycemic control, with the added benefits of weight loss (vs weight gain with b-INS therapy) and a lower incidence of hypoglycemic events. These results suggest that EQW is an alternative treatment to b-INS for patients with type 2 diabetes mellitus and a baseline HbA1c level ≥ 8.5%.

Stochastic production phase design for an open pit mining complex with multiple processing streams

NASA Astrophysics Data System (ADS)

Asad, Mohammad Waqar Ali; Dimitrakopoulos, Roussos; van Eldert, Jeroen

2014-08-01

In a mining complex, the mine is a source of supply of valuable material (ore) to a number of processes that convert the raw ore to a saleable product or a metal concentrate for production of the refined metal. In this context, expected variation in metal content throughout the extent of the orebody defines the inherent uncertainty in the supply of ore, which impacts the subsequent ore and metal production targets. Traditional optimization methods for designing production phases and ultimate pit limit of an open pit mine not only ignore the uncertainty in metal content, but, in addition, commonly assume that the mine delivers ore to a single processing facility. A stochastic network flow approach is proposed that jointly integrates uncertainty in supply of ore and multiple ore destinations into the development of production phase design and ultimate pit limit. An application at a copper mine demonstrates the intricacies of the new approach. The case study shows a 14% higher discounted cash flow when compared to the traditional approach.

Nanocrystalline Iron-Ore-Based Catalysts for Fischer-Tropsch Synthesis.

PubMed

Yong, Seok; Park, Ji Chan; Lee, Ho-Tae; Yang, Jung-Il; Hong, SungJun; Jung, Heon; Chun, Dong Hyun

2016-02-01

Nanocrystalline iron ore particles were fabricated by a wet-milling process using an Ultra Apex Mill, after which they were used as raw materials of iron-based catalysts for low-temperature Fischer-Tropsch synthesis (FTS) below 280 degrees C, which usually requires catalysts with a high surface area, a large pore volume, and a small crystallite size. The wet-milling process using the Ultra Apex Mill effectively destroyed the initial crystallite structure of the natural iron ores of several tens to hundreds of nanometers in size, resulting in the generation of nanocrystalline iron ore particles with a high surface area and a large pore volume. The iron-ore-based catalysts prepared from the nanocrystalline iron ore particles effectively catalyzed the low-temperature FTS, displaying a high CO conversion (about 90%) and good C5+ hydrocarbon productivity (about 0.22 g/g(cat)(-h)). This demonstrates the feasibility of using the iron-ore-based catalysts as inexpensive and disposable catalysts for the low-temperature FTS.

Genesis of the Datuanshan stratabound skarn Cu(-Mo) deposit, Middle-Lower Yangtze Valley, Eastern China: constraints from geology, Re-Os geochronology, mineralogy, and sulfur isotopes

NASA Astrophysics Data System (ADS)

Cao, Yi; Gao, Fuping; Du, Yangsong; Du, Yilun; Pang, Zhenshan

2017-03-01

Stratabound deposits are the most abundant and economically significant ore type in the Middle-Lower Yangtze River Valley, one of the most important metallogenic belts in China. The Datuanshan deposit is one of the largest and most representative stratabound Cu(-Mo) deposits in the Tongling district of the Middle-Lower Yangtze River metallogenic belt. All the orebodies of the Datuanshan deposit occur around Mesozoic quartz monzodiorite and are tabular or semi-tabular bodies along bedding-parallel faults within upper Permian to Lower Triassic strata. However, discordant and crosscutting relationships (e.g., the host rocks crosscut by skarn- and quartz-sulfide veins, with alteration halos around the veins) have also been found, especially along the skarn-host contact and orebody-host contact, indicating that skarnitization and mineralization postdated the deposition of the host sediments. The skarn consists mainly of prograde garnet and pyroxene and retrograde alteration assemblages of amphibole, epidote, and chlorite, as well as quartz and sulfides. Electron microprobe analyses show that the garnets and pyroxenes are grossular-andradite and hedenbergite-diopside series, respectively, and all samples plot in the field of typical skarn copper deposits worldwide. Molybdenite samples from stratiform copper ores yield Re-Os model ages of 138.2-139.9 Ma with a weighted mean age of 139.2 ± 0.9 Ma. This is reasonably consistent with the ages of the stratiform Mo ores (138.0-140.8 Ma) and genetically related quartz monzodiorite (135.2-139.3 Ma) in the Datuanshan deposit, indicating that the stratiform Cu and Mo mineralization was contemporaneous with emplacement of the quartz monzodiorite magmas in the Early Cretaceous. Fifteen δ34S values for sulfides range from -1.8 to +4.7 ‰, with a mean of 0.5 ‰, indicating that the sulfur was derived mainly from a magmatic source. Moreover, the sulfur isotope values of the ores are consistent with those of Mesozoic intermediate-acid intrusions but are different from those of sediments in the Shizishan orefield. Based on these lines of evidence, we conclude that the Datuanshan stratabound Cu(-Mo) deposit is the result of replacement related to Mesozoic magmatic rocks and is not a product of submarine exhalative sedimentary processes.

Geology of the Eymir iron mine, Edremit, Turkey

USGS Publications Warehouse

Jacobson, Herbert Samuel; Turet, Erdogan

1972-01-01

The Eymir mine near Edremit on Turkey's Aegean coast (long 27?30'E.,1at 39?36'N.) was investigated as part of the Maden Tetkik ve Arama Enstitutsu (MTA)-U. S. Geological Survey (USGS) mineral exploration and training project, for the purpose of increasing the known mineral reserves. Geologic mapping of the mine area indicates that hematite is restricted to argillized, silicified, and pyritized dacite and possibly andesite. Hematite is present as massive replacements, impregnations, disseminations, and fracture fillings. Most of the upper part of the iron deposit consists of a breccia composed mostly of silicifiled dacite fragments in a hematite matrix. The iron deposit was apparently formed in three steps: 1. Argillation, silicification, and pyritization of the andesitic lava and dacite units as a result of a regional intrusion. 2. Intrusion of the Dere Oren dacite stock, with associated faulting, fracturing, and breccia formation at the surface. 3. Deposition of hematite by oxidation of pyrite, and transfer of iron via fractures and faults by hydrothermal or meteoric fluids. The Eymir iron deposit is a blanketlike deposit on the crest of the Sivritepe-Eymir ridge. It is 1300 meters long, 80 to 450 meters wide, and has an average thickness of 18.6 meters. Drill holes in the deposit show the iron content to range from 32.0 to 57.6 percent, and to average 46.5 percent. Most of the gangue is silica, and an arsenic impurity averaging 0.39 percent is present. Most of the deposit cannot be utilized as iron ore because of low iron content, high silica content, and high arsenic content. Ore-dressing tests have shown that it is feasible to concentrate the low-grade material, producing a concentrate having increased iron content and reduced silica content. Tests have shown also that the arsenic content of the ore can be reduced substantially by sintering. Further tests and economic feasibility studies are necessary to determine whether an economic marketable iron ore can be produced. If such studies indicate the technical and economic feasibility of utilizing all the Eymir iron deposit, detailed additional studies are recommended including: 1. A detailed drilling and sampling program to include 60 drill holes averaging 40 meters in depth and detailed sampling of mine dumps. 2. Pilot-plant testing of concentration and sintering procedures. 3. A detailed pre-investment economic feasibility study.

3&4D Geomodeling Applied to Mineral Resources Exploration - A New Tool for Targeting Deposits.

NASA Astrophysics Data System (ADS)

Royer, Jean-Jacques; Mejia, Pablo; Caumon, Guillaume; Collon-Drouaillet, Pauline

2013-04-01

3 & 4D geomodeling, a computer method for reconstituting the past deformation history of geological formations, has been used in oil and gas exploration for more than a decade for reconstituting fluid migration. It begins nowadays to be applied for exploring with new eyes old mature mining fields and new prospects. We describe shortly the 3&4D geomodeling basic notions, concepts, and methodology when applied to mineral resources assessment and modeling ore deposits, pointing out the advantages, recommendations and limitations, together with new challenges they rise. Several 3D GeoModels of mining explorations selected across Europe will be presented as illustrative case studies which have been achieved during the EU FP7 ProMine research project. It includes: (i) the Cu-Au porphyry deposits in the Hellenic Belt (Greece); (ii) the VMS in the Iberian Pyrite Belt including the Neves Corvo deposit (Portugal) and (iii) the sediment-hosted polymetallic Cu-Ag (Au, PGE) Kupferschiefer ore deposit in the Foresudetic Belt (Poland). In each case full 3D models using surfaces and regular grid (Sgrid) were built from all dataset available from exploration and exploitation including geological primary maps, 2D seismic cross-sections, and boreholes. The level of knowledge may differ from one site to another however those 3D resulting models were used to pilot additional field and exploration works. In the case of the Kupferschiefer, a sequential restoration-decompaction (4D geomodeling) from the Upper Permian to Cenozoic was conducted in the Lubin- Sieroszowice district of Poland. The results help in better understanding the various superimposed mineralization events which occurred through time in this copper deposit. A hydro-fracturing index was then calculated from the estimated overpressures during a Late Cretaceous-Early Paleocene up-lifting, and seems to correlate with the copper content distribution in the ore-series. These results are in agreement with an Early Paleocene paleomagnetic dating in the Germany part of the Kupferschiefer ore, and which perhaps represents the last mineralizing stages. Last, we discuss perspectives and make recommendations on applying 3&4 geomodeling in mineral resources appraisal. The above research received funding from the European Union's Seventh Framework Program under grant agreement 228559 (ProMine project).

Bald Mountain gold mining district, Nevada: A Jurassic reduced intrusion-related gold system

USGS Publications Warehouse

Nutt, C.J.; Hofstra, A.H.

2007-01-01

The Bald Mountain mining district has produced about 2 million ounces (Moz) of An. Geologic mapping, field relationships, geochemical data, petrographic observations, fluid inclusion characteristics, and Pb, S, O, and H isotope data indicate that An mineralization was associated with a reduced Jurassic intrusion. Gold deposits are localized within and surrounding a Jurassic (159 Ma) quartz monzonite porphyry pluton and dike complex that intrudes Cambrian to Mississippian carbonate and clastic rocks. The pluton, associated dikes, and An mineralization were controlled by a crustal-scale northwest-trending structure named the Bida trend. Gold deposits are localized by fracture networks in the pluton and the contact metamorphic aureole, dike margins, high-angle faults, and certain strata or shale-limestone contacts in sedimentary rocks. Gold mineralization was accompanied by silicification and phyllic alteration, ??argillic alteration at shallow levels. Although An is typically present throughout, the system exhibits a classic concentric geochemical zonation pattern with Mo, W, Bi, and Cu near the center, Ag, Pb, and Zn at intermediate distances, and As and Sb peripheral to the intrusion. Near the center of the system, micron-sized native An occurs with base metal sulfides and sulfosalts. In peripheral deposits and in later stages of mineralization, Au is typically submicron in size and resides in pyrite or arsenopyrite. Electron microprobe and laser ablation ICP-MS analyses show that arsenopyrite, pyrite, and Bi sulfide minerals contain 10s to 1,000s of ppm Au. Ore-forming fluids were aqueous and carbonic at deep levels and episodically hypersaline at shallow levels due to boiling. The isotopic compositions of H and O in quartz and sericite and S and Pb in sulfides are indicative of magmatic ore fluids with sedimentary sulfur. Together, the evidence suggests that Au was introduced by reduced S-bearing magmatic fluids derived from a reduced intrusion. The reduced character of the intrusion was caused by assimilation of carbonaceous sedimentary rocks. Tertiary faults dismember the area and drop down the upper part of the mineralizing system to the west. The abundant and widespread kaolinite in oxide ores is relatively disordered (1A polytype) and has ??D and ??18O values suggestive of a supergene origin. The deep weathering and oxidation of the ores associated with exhumation made them amenable to open-pit mining and processing using cyanide heap leach methods. ?? 2007 Society of Economic Geologists, Inc.

Lithium

USGS Publications Warehouse

Ober, J.

1998-01-01

The lithium industry can be divided into two sectors: ore concentrate producers and chemical producers. Ore concentrate producers mine lithium minerals. They beneficiate the ores to produce material for use in ceramics and glass manufacturing.

Difference in rockburst hazard in ore and coal mines

NASA Astrophysics Data System (ADS)

Lovchikov, AV

2018-03-01

In the Russian mining and engineering literature, in most cases, there is no difference in the assessment of the rockburst hazards in metal and coal mines. Nevertheless, it exists, in view of the difference in geological and geotechnical conditions of coal and ore deposits. Since ore deposits occur in the solid magmatic or metamorphic rock masses, the strongest induced earthquakes are much more powerful in ore mines than in coal mines. The main difference of rockbursting lies in the difference of natural stress state: gravity stress state in the coal fields and gravity-and-tectonic stress state in ore mines. The actual stresses are mostly vertical in the first case and horizontal in the second case, which conditions the difference in rockburst hazard in coal and ore mines.

SEVENTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

2012-08-30

A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. Seventy tests using mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they meet the criterion of leak-tightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. High temperature aging continues for 23more » GLT O-ring fixtures at 200 – 270 ºF. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The remaining GLT O-ring fixtures aging at 300 ºF have been retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 54-72 months, which is still bounding to O-ring temperatures during storage in K-Area Complex (KAC). Based on expectations that the fixtures aging at 200 ºF will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging in 2011 at an intermediate temperature of 270 ºF, with hopes that they may reach a failure condition before the 200 ºF fixtures. High temperature aging continues for 6 GLT-S O-ring fixtures at 200 – 300 ºF. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 ºF. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 - 300 ºF for 30 - 36 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the O-rings displayed a compression set ranging from 51 – 96%. This is greater than seen to date for any packages inspected during KAC field surveillance (24% average). For GLT O-rings, separate service life estimates have been made based on the O-ring fixture leak test data and based on compression stress relaxation (CSR) data. These two predictive models show reasonable agreement at higher temperatures (350 – 400 ºF). However, at 300 ºF, the room temperature leak test failures to date experienced longer aging times than predicted by the CSRbased model. This suggests that extrapolations of the CSR model predictions to temperatures below 300 ºF will provide a conservative prediction of service life relative to the leak rate criterion. Leak test failure data at lower temperatures are needed to verify this apparent trend. Insufficient failure data exist currently to perform a similar comparison for GLT-S O-rings. Aging and periodic leak testing will continue for the remaining PCV O-ring fixtures.« less

Geologic history of the Blackbird Co-Cu district in the Lemhi subbasin of the Belt-Purcell Basin

USGS Publications Warehouse

Bookstrom, Arthur A.; Box, Stephen E.; Cossette, Pamela M.; Frost, Thomas P.; Gillerman, Virginia; King, George; Zirakparvar, N. Alex

2016-01-01

The Blackbird cobalt-copper (Co-Cu) district in the Salmon River Mountains of east-central Idaho occupies the central part of the Idaho cobalt belt—a northwest-elongate, 55-km-long belt of Co-Cu occurrences, hosted in grayish siliciclastic metasedimentary strata of the Lemhi subbasin (of the Mesoproterozoic Belt-Purcell Basin). The Blackbird district contains at least eight stratabound ore zones and many discordant lodes, mostly in the upper part of the banded siltite unit of the Apple Creek Formation of Yellow Lake, which generally consists of interbedded siltite and argillite. In the Blackbird mine area, argillite beds in six stratigraphic intervals are altered to biotitite containing over 75 vol% of greenish hydrothermal biotite, which is preferentially mineralized.Past production and currently estimated resources of the Blackbird district total ~17 Mt of ore, averaging 0.74% Co, 1.4% Cu, and 1.0 ppm Au (not including downdip projections of ore zones that are open downward). A compilation of relative-age relationships and isotopic age determinations indicates that most cobalt mineralization occurred in Mesoproterozoic time, whereas most copper mineralization occurred in Cretaceous time.Mesoproterozoic cobaltite mineralization accompanied and followed dynamothermal metamorphism and bimodal plutonism during the Middle Mesoproterozoic East Kootenay orogeny (ca. 1379–1325 Ma), and also accompanied Grenvilleage (Late Mesoproterozoic) thermal metamorphism (ca. 1200–1000 Ma). Stratabound cobaltite-biotite ore zones typically contain cobaltite1 in a matrix of biotitite ± tourmaline ± minor xenotime (ca. 1370–1320 Ma) ± minor chalcopyrite ± sparse allanite ± sparse microscopic native gold in cobaltite. Such cobaltite-biotite lodes are locally folded into tight F2 folds with axial-planar S2 cleavage and schistosity. Discordant replacement-style lodes of cobaltite2-biotite ore ± xenotime2 (ca. 1320–1270 Ma) commonly follow S2fractures and fabrics. Discordant quartz-biotite and quartz-tourmaline breccias, and veins contain cobaltite3 ± xenotime3 (ca. 1058–990 Ma).Mesoproterozoic cobaltite deposition was followed by: (1) within-plate plutonism (530–485 Ma) and emplacement of mafic dikes (which cut cobaltite lodes but are cut by quartz-Fe-Cu-sulfide veins); (2) garnet-grade metamorphism (ca. 151–93 Ma); (3) Fe-Cu-sulfide mineralization (ca. 110–92 Ma); and (4) minor quartz ± Au-Ag ± Bi mineralization (ca. 92–83 Ma).Cretaceous Fe-Cu-sulfide vein, breccia, and replacement-style deposits contain various combinations of chalcopyrite ± pyrrhotite ± pyrite ± cobaltian arsenopyrite (not cobaltite) ± arsenopyrite ± quartz ± siderite ± monazite (ca. 144–88 Ma but mostly 110–92 Ma) ± xenotime (104–93 Ma). Highly radiogenic Pb (in these sulfides) and Sr (in siderite) indicate that these elements resided in Mesoproterozoic source rocks until they were mobilized after ca. 100 Ma. Fe-Cu-sulfide veins, breccias, and replacement deposits appear relatively undeformed and generally lack metamorphic fabrics.Composite Co-Cu-Au ore contains early cobaltite-biotite lodes, cut by Fe-Cu-sulfide veins and breccias, or overprinted by Fe-Cu-sulfide replacement-style deposits, and locally cut by quartz veinlets ± Au-Ag ± Bi minerals.

Genesis of sediment-hosted stratiform copper cobalt deposits, central African Copperbelt

NASA Astrophysics Data System (ADS)

Cailteux, J. L. H.; Kampunzu, A. B.; Lerouge, C.; Kaputo, A. K.; Milesi, J. P.

2005-07-01

The Neoproterozoic central African Copperbelt is one of the greatest sediment-hosted stratiform Cu-Co provinces in the world, totalling 140 Mt copper and 6 Mt cobalt and including several world-class deposits (⩾10 Mt copper). The origin of Cu-Co mineralisation in this province remains speculative, with the debate centred around syngenetic-diagenetic and hydrothermal-diagenetic hypotheses. The regional distribution of metals indicates that most of the cobalt-rich copper deposits are hosted in dolomites and dolomitic shales forming allochthonous units exposed in Congo and known as Congolese facies of the Katangan sedimentary succession (average Co:Cu = 1:13). The highest Co:Cu ratio (up to 3:1) occurs in ore deposits located along the southern structural block of the Lufilian Arc. The predominantly siliciclastic Zambian facies, exposed in Zambia and in SE Congo, forms para-autochthonous sedimentary units hosting ore deposits characterized by lower a Co:Cu ratio (average 1:57). Transitional lithofacies in Zambia (e.g. Baluba, Mindola) and in Congo (e.g. Lubembe) indicate a gradual transition in the Katangan basin during the deposition of laterally correlative clastic and carbonate sedimentary rocks exposed in Zambia and in Congo, and are marked by Co:Cu ratios in the range 1:15. The main Cu-Co orebodies occur at the base of the Mines/Musoshi Subgroup, which is characterized by evaporitic intertidal-supratidal sedimentary rocks. All additional lenticular orebodies known in the upper part of the Mines/Musoshi Subgroup are hosted in similar sedimentary rocks, suggesting highly favourable conditions for the ore genesis in particular sedimentary environments. Pre-lithification sedimentary structures affecting disseminated sulphides indicate that metals were deposited before compaction and consolidation of the host sediment. The ore parageneses indicate several generations of sulphides marking syngenetic, early diagenetic and late diagenetic processes. Sulphur isotopic data on sulphides suggest the derivation of sulphur essentially from the bacterial reduction of seawater sulphates. The mineralizing brines were generated from sea water in sabkhas or hypersaline lagoons during the deposition of the host rocks. Changes of Eh-pH and salinity probably were critical for concentrating copper-cobalt and nickel mineralisation. Compressional tectonic and related metamorphic processes and supergene enrichment have played variable roles in the remobilisation and upgrading of the primary mineralisation. There is no evidence to support models assuming that metals originated from: (1) Katangan igneous rocks and related hydrothermal processes or; (2) leaching of red beds underlying the orebodies. The metal sources are pre-Katangan continental rocks, especially the Palaeoproterozoic low-grade porphyry copper deposits known in the Bangweulu block and subsidiary Cu-Co-Ni deposits/occurrences in the Archaean rocks of the Zimbabwe craton. These two sources contain low grade ore deposits portraying the peculiar metal association (Cu, Co, Ni, U, Cr, Au, Ag, PGE) recorded in the Katangan sediment-hosted ore deposits. Metals were transported into the basin dissolved in water. The stratiform deposits of Congo and Zambia display features indicating that syngenetic and early diagenetic processes controlled the formation of the Neoproterozoic Copperbelt of central Africa.

Prediction of ore fluid metal concentrations from solid solution concentrations in ore-stage calcite: Application to the Illinois-Kentucky and Central Tennessee Mississippi Valley-type districts

NASA Astrophysics Data System (ADS)

Smith-Schmitz, Sarah E.; Appold, Martin S.

2018-03-01

Knowledge of the concentrations of Zn and Pb in Mississippi Valley-type (MVT) ore fluids is fundamental to understanding MVT deposit origin. Most previous attempts to quantify the concentrations of Zn and Pb in MVT ore fluids have focused on the analysis of fluid inclusions. However, these attempts have yielded ambiguous results due to possible contamination from secondary fluid inclusions, interferences from Zn and Pb in the host mineral matrix, and uncertainties about whether the measured Zn and Pb signals represent aqueous solute or accidental solid inclusions entrained within the fluid inclusions. The purpose of the present study, therefore, was to try to determine Zn and Pb concentrations in MVT ore fluids using an alternate method that avoids these ambiguities by calculating Zn and Pb concentrations in MVT ore fluids theoretically based on their solid solution concentrations in calcite. This method was applied to the Illinois-Kentucky and Central Tennessee districts, which both contain ore-stage calcite. Experimental partition coefficient (D) values from Rimstidt et al. (1998) and Tsusue and Holland (1966), and theoretical thermodynamic distribution coefficient (KD) values were employed in the present study. Ore fluid concentrations of Zn were likely most accurately predicted by Rimstidt et al. (1998) D values, based on their success in predicting known fluid inclusion concentrations of Mg and Mn, and likely also most accurately predicted ore fluid concentrations of Fe. All four of these elements have a divalent ionic radius smaller than that of Ca2+ and form carbonate minerals with the calcite structure. For both the Illinois-Kentucky and the Central Tennessee district, predicted ore fluid Zn and Fe concentrations were on the order of up to 10's of ppm. Ore fluid concentrations of Pb could only be predicted using Rimstidt et al. (1998) D values. However, these concentrations are unlikely to be reliable, as predicted ore fluid concentrations of Sr and Ba, which like Pb also have a divalent ionic radius larger than that of Ca2+ and form carbonate minerals with the aragonite structure, did not consistently agree well with known concentrations of Sr and Ba in fluid inclusions. The ore fluid Zn concentrations predicted in the present study lie within the range of Zn concentrations typical of modern sedimentary brines and are high enough to allow deposition of the observed amounts of Zn in the Illinois-Kentucky and Central Tennessee districts within ranges of geologically reasonable times and ore fluid flow velocities. If the pH of the Illinois-Kentucky and Central pH ore fluids was as low as current evidence suggests to be possible, then these ore fluids could simultaneously have transported enough sulfide with their Zn to account for the observed amounts of sphalerite in the districts.

Ores and Climate Change - Primary Shareholders

NASA Astrophysics Data System (ADS)

Stein, Holly J.; Hannah, Judith L.

2015-04-01

Many in the economic geology community concern themselves with details of ore formation at the deposit scale, whether tallying fluid inclusion data to get at changes in ore-forming fluids or defining structures that aid and abet mineralization. These compilations are generally aimed at interpretation of events at the site of ore formation, with the goal being assignment of the deposit to a sanctioned ore deposit model. While providing useful data, this approach is incomplete and does not, by itself, serve present-day requirements for true interdisciplinary science. The ore-forming environment is one of chaos and disequilibrium at nearly all scales (Stein, 2014). Chaos and complexity are documented by variably altered rocks, veins or disseminated mineralization with multi-generational fluid histories, erratic and unusual textures in host rocks, and the bitumen or other hydrocarbon products entwined within many ore deposits. This should give pause to our drive for more data as a means to find "the answer". The answer lies in the kind of data collected and more importantly, in the way we interpret those data. Rather than constructing an ever-increasing catalog of descriptive mutations on sanctioned ore deposit models (e.g., IOGC or Iron-Oxide Copper Gold deposits), the way forward is to link source and transport of metals, sulfur, and organic material with regional and ultimately whole Earth chemical evolution. Important experimental work provides chemical constraints in controlled and behaved environments. To these data, we add imagination and interpretation, always tying back to field observations. In this paper, several key points are made by way of ore deposit examples: (1) many IOCG deposits are outcomes of profound changes in the chemistry of the Earth's surface, in the interplay of the atmosphere, hydrosphere, biosphere, and lithosphere; (2) the redox history of Fe in deep earth may be ultimately expressed in the ore-forming sequence; and (3) the formation of many giant Cu-Mo-Au ore deposits may be arrested when the surface is catastrophically breached, as multiple km-scale breccia pipes empty their volatile and metal contents into the atmosphere. The new equation for studying ore geology should be one that reconstructs ore formation from beginning to end, that is, from source, release, and transport, to breach. Of course, detailed measurements and mapping of ore bodies remains essential, but a full understanding of metal migration and budgets can only be achieved if we model what might have been left behind in deeper Earth, and what may have been lost to the atmosphere. To do this, we need to understand much more than the geology at our ore deposit of interest. Stein, H.J. (2014) Dating and Tracing the History of Ore Formation. Treatise on Geochemistry 13: 87-118. Elsevier. Support for time to think - CHRONOS, funded by a consortium of Norwegian petroleum companies.

Impact of solvent extraction organics on adsorption and bioleaching of A. ferrooxidans and L. ferriphilum

NASA Astrophysics Data System (ADS)

Hualong, Yu; Xiaorong, Liu

2017-04-01

Copper solvent extraction entrained and dissoluted organics (SX organics) in the raffinate during SX operation can contaminated chalcopyrite ores and influence bioleaching efficiency by raffinate recycling. The adsorption and bioleaching of A. ferrooxidans and L. ferriphilum with contaminated ores were investigated. The results showed that, A. ferrooxidans and L. ferriphilum cells could adsorb quickly on minerals, the adsorption rate on contaminated ores were 83% and 60%, respectively, larger than on uncontaminated ores. However, in the bioleaching by the two kinds of acid bacterias, contaminated ores presented a lower bioleaching efficiency.

O-Ring sealing arrangements for ultra-high vacuum systems

DOEpatents

Kim, Chang-Kyo; Flaherty, Robert

1981-01-01

An all metal reusable O-ring sealing arrangement for sealing two concentric tubes in an ultra-high vacuum system. An O-ring of a heat recoverable alloy such as Nitinol is concentrically positioned between protruding sealing rings of the concentric tubes. The O-ring is installed between the tubes while in a stressed martensitic state and is made to undergo a thermally induced transformation to an austenitic state. During the transformation the O-ring expands outwardly and contracts inwardly toward a previously sized austenitic configuration, thereby sealing against the protruding sealing rings of the concentric tubes.

Antimony ore in the Fairbanks district, Alaska

USGS Publications Warehouse

Killeen, Pemberton Lewis; Mertie, John B.

1951-01-01

Antimony-bearing ores in the Fairbanks district, Alaska, are found principally in two areas, the extremities of which are at points 10 miles west and 23 miles northeast of Fairbanks; and one of two minor areas lies along this same trend 30 miles farther to the northeast. These areas are probably only local manifestations of mineralization that affected a much broader area and formed antimony-bearing deposits in neighboring districts, the closest of which is 50 miles away. The ores were exposed largely as a result of lode gold mining, but at two periods in the past, high prices for antimony ore warranted an independent production and about 2500 tons of stibnite ore was shipped. The sulfide deposits occupy the same fractures along which a gold-quartz mineralization of greater economic importance occurred; and both are probably genetically related to igneous rocks which intrude the schistose country rock. The sulfide is in part contemporaneous with some late-stage quartz in which it occurs as disseminated crystals; and in part the latest filling in the mineralized zones where it forms kidney-shaped masses of essentially solid sulfide. One extremely long mass must have contained nearly 100 tons of ore, but the average of the larger kidneys is closer to several tons. Much of the ore is stibnite, with quartz as a minor impurity, and assays show the tenor to vary from 40 to 65 percent antimony. Sulphantimonites are less abundant but likewise occur as disseminated crystals and as kidney-shaped bodies. Antimony oxides appear on the weathered surface and along fractures within the sulfide ore. Deposits containing either stibnite or sulphantimonite are known at more than 50 localities, but only eighteen have produced ore and the bulk of this came from the mines. The geology of the deposit, and the nature, extent, and period of the workings are covered in the detailed descriptions of individual occurrences. Several geologic and economic factors, which greatly affect prospecting and mining for stibnite ore in the area, are outlined. The principal available ore and reserves are considered to be ores earlier mined but never shipped, ore minable from near-surface deposits, and ores recoverable as a by-product of future gold mining. The outlook for stibnite production in the district is very uncertain. Apparently the greater portion of stibnite ore has already been recovered and present operations will strip the two principal areas of the district. This conclusion is based on the scanty discoveries since the last war and the fact that the areas are so pock-marked with prospects that there is little likelihood that any other large near-surface bodies remain to be discovered. Future prospecting would essentially be limited to attempts to seek the continuation of lodes previously having high yields of stibnite.

A Comprehensive Expedient Methods Field Manual.

DTIC Science & Technology

1984-09-01

structures. " Revetments may be constructed of sandbags, sod blocks , and other expedients [17:933." Bunkers are emplacements with overhead protective...Lapland Fence............................. 75 19. Hardening: Dimensional Timber (Soil Bin) Revetment ............................................. 76...20. Hardening: Log Bulkhead (Soil Bin) Revetment ... 77 21. Hardening: Landing Mat Bulkhead (Soil Bin) Revetment

Geochemistry and geochronology of ore-bearing and barren intrusions in the Luanchuan ore fields of East Qinling metallogenic belt, China: Diverse tectonic evolution and implications for mineral exploration

NASA Astrophysics Data System (ADS)

Xue, Fei; Wang, Gongwen; Santosh, M.; Yang, Fan; Shen, Zhiwei; Kong, Liang; Guo, Nana; Zhang, Xuhuang; Jia, Wenjuan

2018-05-01

The Luanchuan ore fields form part of the East Qinling metallogenic belt in central China. In this study, we compare two ore-bearing intrusions, the Shibaogou granitic pluton (SBG) and the Zhongyuku granitic pluton (ZYK), with the ore-barren Laojunshan intrusion (LJS) from the Luanchuan ore field. Geochemically, all the three intrusions are characterized by high-Si, high-K, and alkalis, together with moderate-ASI, exhibiting I-type granite features. The rocks, especially the ore-related plutons also show enrichment in LREEs. Mineral chemistry of biotite from the intrusions exhibits similar features of high Si and Mg, and low Al and Fe. Zircon grains from the ZYK intrusion yielded a U-Pb age of 149.6 ± 2.4 Ma. The zircon grains show εHf (t) values and two stage model ages (TDM2) in the range of -16.8 to -19.7 and 1998-2156 Ma respectively. The biotite composition and Hf isotopic data indicate that the magma was derived by re-melting of deep crustal material with minor input of mantle components. We evaluate the results to understand the physico-chemical conditions, petrogenesis, and tectonic setting, and their implications for mineral exploration. The ore-bearing plutons show wide ranges of temperature and oxygen fugacity, favoring Mo-W mineralization. In addition, estimates on pressure and depth of emplacement suggest that lower solidification pressure in a decompressional setting contributed to the evolution of magmatic hydrothermal deposits. Our data suggest that the ZYK has the highest potential for Mo-W mineralization. The ore-bearing plutons of ZYK and SBG were formed in a transitional tectonic setting from compression to extension, with the large-scale metallogeny triggered by slab melts at ca. 145 Ma. However, the ore-barren LJS batholith formed in an extension-related geodynamic setting at ∼115 Ma. Our study shows that different tectonic settings and consequent physico-chemical conditions dictated the ore potential of the intrusions in the Luanchuan ore district.

Suppression of Prostate Tumor Progression by Bin 1

DTIC Science & Technology

2006-02-01

experiment). The full protocol was approved by IACUC review. Cohort A. Castration + Testostrone propionate s.c. + MNU i.v. Cohort B. Castration... Testostrone propionate s.c. + MNU i.v. + testosterone pellet Strain 1. mosaic Bin1 flox)/KO  Strain 2. Bin1 flox/+ (control for strain 1) Strain

Bioinformatics and Astrophysics Cluster (BinAc)

NASA Astrophysics Data System (ADS)

Krüger, Jens; Lutz, Volker; Bartusch, Felix; Dilling, Werner; Gorska, Anna; Schäfer, Christoph; Walter, Thomas

2017-09-01

BinAC provides central high performance computing capacities for bioinformaticians and astrophysicists from the state of Baden-Württemberg. The bwForCluster BinAC is part of the implementation concept for scientific computing for the universities in Baden-Württemberg. Community specific support is offered through the bwHPC-C5 project.

EFFECTS OF NUMBER AND LOCATION OF BINS ON PLASTIC RECYCLING AT A UNIVERSITY

PubMed Central

O'Connor, Ryan T; Lerman, Dorothea C; Fritz, Jennifer N; Hodde, Henry B

2010-01-01

The proportion of plastic bottles that consumers placed in appropriate recycling receptacles rather than trash bins was examined across 3 buildings on a university campus. We extended previous research on interventions to increase recycling by controlling the number of recycling receptacles across conditions and by examining receptacle location without the use of posted signs. Manipulating the appearance or number of recycling bins in common areas did not increase recycling. Consumers recycled substantially more plastic bottles when the recycling bins were located in classrooms. PMID:21541154

Effects of number and location of bins on plastic recycling at a university.

PubMed

O'Connor, Ryan T; Lerman, Dorothea C; Fritz, Jennifer N; Hodde, Henry B

2010-01-01

The proportion of plastic bottles that consumers placed in appropriate recycling receptacles rather than trash bins was examined across 3 buildings on a university campus. We extended previous research on interventions to increase recycling by controlling the number of recycling receptacles across conditions and by examining receptacle location without the use of posted signs. Manipulating the appearance or number of recycling bins in common areas did not increase recycling. Consumers recycled substantially more plastic bottles when the recycling bins were located in classrooms.

BinMag: Widget for comparing stellar observed with theoretical spectra

NASA Astrophysics Data System (ADS)

Kochukhov, O.

2018-05-01

BinMag examines theoretical stellar spectra computed with Synth/SynthMag/Synmast/Synth3/SME spectrum synthesis codes and compare them to observations. An IDL widget program, BinMag applies radial velocity shift and broadening to the theoretical spectra to account for the effects of stellar rotation, radial-tangential macroturbulence, instrumental smearing. The code can also simulate spectra of spectroscopic binary stars by appropriate coaddition of two synthetic spectra. Additionally, BinMag can be used to measure equivalent width, fit line profile shapes with analytical functions, and to automatically determine radial velocity and broadening parameters. BinMag interfaces with the Synth3 (ascl:1212.010) and SME (ascl:1202.013) codes, allowing the user to determine chemical abundances and stellar atmospheric parameters from the observed spectra.

Effects of empty bins on image upscaling in capsule endoscopy

NASA Astrophysics Data System (ADS)

Rukundo, Olivier

2017-07-01

This paper presents a preliminary study of the effect of empty bins on image upscaling in capsule endoscopy. The presented study was conducted based on results of existing contrast enhancement and interpolation methods. A low contrast enhancement method based on pixels consecutiveness and modified bilinear weighting scheme has been developed to distinguish between necessary empty bins and unnecessary empty bins in the effort to minimize the number of empty bins in the input image, before further processing. Linear interpolation methods have been used for upscaling input images with stretched histograms. Upscaling error differences and similarity indices between pairs of interpolation methods have been quantified using the mean squared error and feature similarity index techniques. Simulation results demonstrated more promising effects using the developed method than other contrast enhancement methods mentioned.

The volatile compound BinBase mass spectral database.

PubMed

Skogerson, Kirsten; Wohlgemuth, Gert; Barupal, Dinesh K; Fiehn, Oliver

2011-08-04

Volatile compounds comprise diverse chemical groups with wide-ranging sources and functions. These compounds originate from major pathways of secondary metabolism in many organisms and play essential roles in chemical ecology in both plant and animal kingdoms. In past decades, sampling methods and instrumentation for the analysis of complex volatile mixtures have improved; however, design and implementation of database tools to process and store the complex datasets have lagged behind. The volatile compound BinBase (vocBinBase) is an automated peak annotation and database system developed for the analysis of GC-TOF-MS data derived from complex volatile mixtures. The vocBinBase DB is an extension of the previously reported metabolite BinBase software developed to track and identify derivatized metabolites. The BinBase algorithm uses deconvoluted spectra and peak metadata (retention index, unique ion, spectral similarity, peak signal-to-noise ratio, and peak purity) from the Leco ChromaTOF software, and annotates peaks using a multi-tiered filtering system with stringent thresholds. The vocBinBase algorithm assigns the identity of compounds existing in the database. Volatile compound assignments are supported by the Adams mass spectral-retention index library, which contains over 2,000 plant-derived volatile compounds. Novel molecules that are not found within vocBinBase are automatically added using strict mass spectral and experimental criteria. Users obtain fully annotated data sheets with quantitative information for all volatile compounds for studies that may consist of thousands of chromatograms. The vocBinBase database may also be queried across different studies, comprising currently 1,537 unique mass spectra generated from 1.7 million deconvoluted mass spectra of 3,435 samples (18 species). Mass spectra with retention indices and volatile profiles are available as free download under the CC-BY agreement (http://vocbinbase.fiehnlab.ucdavis.edu). The BinBase database algorithms have been successfully modified to allow for tracking and identification of volatile compounds in complex mixtures. The database is capable of annotating large datasets (hundreds to thousands of samples) and is well-suited for between-study comparisons such as chemotaxonomy investigations. This novel volatile compound database tool is applicable to research fields spanning chemical ecology to human health. The BinBase source code is freely available at http://binbase.sourceforge.net/ under the LGPL 2.0 license agreement.

The volatile compound BinBase mass spectral database

PubMed Central

2011-01-01

Background Volatile compounds comprise diverse chemical groups with wide-ranging sources and functions. These compounds originate from major pathways of secondary metabolism in many organisms and play essential roles in chemical ecology in both plant and animal kingdoms. In past decades, sampling methods and instrumentation for the analysis of complex volatile mixtures have improved; however, design and implementation of database tools to process and store the complex datasets have lagged behind. Description The volatile compound BinBase (vocBinBase) is an automated peak annotation and database system developed for the analysis of GC-TOF-MS data derived from complex volatile mixtures. The vocBinBase DB is an extension of the previously reported metabolite BinBase software developed to track and identify derivatized metabolites. The BinBase algorithm uses deconvoluted spectra and peak metadata (retention index, unique ion, spectral similarity, peak signal-to-noise ratio, and peak purity) from the Leco ChromaTOF software, and annotates peaks using a multi-tiered filtering system with stringent thresholds. The vocBinBase algorithm assigns the identity of compounds existing in the database. Volatile compound assignments are supported by the Adams mass spectral-retention index library, which contains over 2,000 plant-derived volatile compounds. Novel molecules that are not found within vocBinBase are automatically added using strict mass spectral and experimental criteria. Users obtain fully annotated data sheets with quantitative information for all volatile compounds for studies that may consist of thousands of chromatograms. The vocBinBase database may also be queried across different studies, comprising currently 1,537 unique mass spectra generated from 1.7 million deconvoluted mass spectra of 3,435 samples (18 species). Mass spectra with retention indices and volatile profiles are available as free download under the CC-BY agreement (http://vocbinbase.fiehnlab.ucdavis.edu). Conclusions The BinBase database algorithms have been successfully modified to allow for tracking and identification of volatile compounds in complex mixtures. The database is capable of annotating large datasets (hundreds to thousands of samples) and is well-suited for between-study comparisons such as chemotaxonomy investigations. This novel volatile compound database tool is applicable to research fields spanning chemical ecology to human health. The BinBase source code is freely available at http://binbase.sourceforge.net/ under the LGPL 2.0 license agreement. PMID:21816034

[Spectral characteristics and implications of quartz from Heliao lead-zinc polymetallic ore district in the south of Qinzhou-Hangzhou joint belt].

PubMed

Lü, Wen-Chao; Yang, Zhi-Jun; Zhou, Yong-Zhang; Li, Hong-Zhong; Zeng, Xiang-Qing; Chen, Qing; Liang, Jin; Zeng, Chang-Yu

2013-05-01

The XRD, FTIR and Raman spectrum were employed to study the characters of quartz from three types of rock samples, which are mineralized rock sample, near ore body rock sample and far away from ore body rock sample in Heliao lead-zinc polymetallic ore district. The research shows that the quartz in the mineralized rock and far away from ore body rock is pure, while the quartz in near ore body rock contains a small amount of impurities. But such small amounts of impurities did not cause apparent change in the quartz lattice parameters. From far away from ore body rock-->near ore body rock-->mineralized rock, the crystallinity and order degree of quartz are higher and higher. And the quartz in the mineralized rock has a trend to change into low symmetry quartz. It's a unique to mineralized rock that the quartz's absorption peak at 1 050 cm(-1) was split into two strongest ones. It can be used as the signs of whether exists mineralization. The cause for the quartz microstructure changes may be related to the activities of late mineralized hydrothermal fluids. Late hydrothermal influence was very weak to the quartz far away from ore body rock. And through the impact of the multi-stage hydrothermal effect, the quartz in mineralized rock may be purified by recrystallization and structural adjustment. However the quartz in near ore body rock didn't have enough hydrothermal influence, so it's not pure. Genealogy research technology is a useful technique for in-depth exploration of study area mineralization process and metallogenic regularity.

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... or its mode of occurrence; (b) mills beneficiating iron ores by physical (magnetic and nonmagnetic) and/or chemical separation; and (c) mills beneficiating iron ores by magnetic and physical separation...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... or its mode of occurrence; (b) mills beneficiating iron ores by physical (magnetic and nonmagnetic) and/or chemical separation; and (c) mills beneficiating iron ores by magnetic and physical separation...

The future of the application of the Bi-Digital O-Ring Test in Sports Psychology.

PubMed

Ozerkan, Kemal Nuri

2005-01-01

The Bi-Digital O-Ring Test, originally developed by Dr. Omura, utilizes changes in the degree of strength of voluntary movements of muscles of the fingers under a definite muscle tonus, making Bi-Digital O-Rings, as an indicator of pathology in the body. Research in Sports Psychology can use the classical measurement methods and Bi-Digital O-Ring Test method comparatively and thus produce new findings regarding the reliability and certainty of the Bi-Digital O-Ring Test test. It seems probable that by using the non-invasive Bi-Digital O-Ring Test test, it is possible to measure enzymes, hormones and neuro-transmitters instantaneously and assess a sports person's actual psychological and physiological performance, and thereby help them reach their peak performance levels during both exercise and competitions.

An efficient indexing scheme for binary feature based biometric database

NASA Astrophysics Data System (ADS)

Gupta, P.; Sana, A.; Mehrotra, H.; Hwang, C. Jinshong

2007-04-01

The paper proposes an efficient indexing scheme for binary feature template using B+ tree. In this scheme the input image is decomposed into approximation, vertical, horizontal and diagonal coefficients using the discrete wavelet transform. The binarized approximation coefficient at second level is divided into four quadrants of equal size and Hamming distance (HD) for each quadrant with respect to sample template of all ones is measured. This HD value of each quadrant is used to generate upper and lower range values which are inserted into B+ tree. The nodes of tree at first level contain the lower and upper range values generated from HD of first quadrant. Similarly, lower and upper range values for the three quadrants are stored in the second, third and fourth level respectively. Finally leaf node contains the set of identifiers. At the time of identification, the test image is used to generate HD for four quadrants. Then the B+ tree is traversed based on the value of HD at every node and terminates to leaf nodes with set of identifiers. The feature vector for each identifier is retrieved from the particular bin of secondary memory and matched with test feature template to get top matches. The proposed scheme is implemented on ear biometric database collected at IIT Kanpur. The system is giving an overall accuracy of 95.8% at penetration rate of 34%.

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 4 2010-04-01 2010-04-01 false Depletion on extraction of ores or minerals from... Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or residue of prior... section 613(c)(3) (relating to extraction of ores or minerals from the ground). Thus, an acquiring...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 4 2013-04-01 2013-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 4 2011-04-01 2011-04-01 false Depletion on extraction of ores or minerals from... Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or residue of prior... section 613(c)(3) (relating to extraction of ores or minerals from the ground). Thus, an acquiring...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 4 2012-04-01 2012-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

Application of LANDSAT satellite imagery for iron ore prospecting in the western desert of Egypt

NASA Technical Reports Server (NTRS)

Elshazly, E. M.; Abdel-Hady, M. A.; Elghawaby, M. A.; Khawasik, S. M. (Principal Investigator)

1977-01-01

The author has identified the following significant results. The delineation of the geological units and geological structures through image interpretation, corroborated by field observations and structural analysis, led to the discovery of new iron ore deposits. A new locality for iron ore deposition, namely Gebel Qalamun, was discovered, as well as new occurrences within the already known iron ore region of Bahariya Oasis.

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 4 2014-04-01 2014-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

Thermal and chemical variations of the Nigerian Benue trough lead-zinc-barite-fluorite deposits

NASA Astrophysics Data System (ADS)

Ogundipe, Ibukun Emmanuel

2017-08-01

The Benue trough is an intra-continental rift initiated in the Cretaceous during the opening of the South Atlantic Ocean. Lead-zinc-barite-fluorite mineralization occurs along the 600 km axis of the trough in three discrete sub-basins which coincide with the lower, middle and upper mineral districts of the Benue Valley. Lithologically these sub-basins are dominated by black carbonaceous shale in the Lower Benue, platform carbonates in the Middle Benue and sandstones in the Upper Benue. Micro-thermometric analysis of fluid inclusions in sphalerite, fluorite, barite and quartz have shown that each mineral district has its own unique thermal and chemical imprint. For example, the temperature can be bracketed between 109 °C and 160 °C for lower Benue, 89 °C-144 °C for the Middle Benue and 176 °C-254 °C for the Upper Benue. Chemical differentiation also exists between each mineral district with the Lower Benue having 22 wt % equivalent NaCl while the Middle and Upper Benue have 18 and 16 wt % equivalent NaCl respectively. This study shows that inter-district thermal and chemical variations exist between the ore-stage sulfide and post-sulfide gangue minerals of the entire Benue Valley. Similarly, intra-district thermal and chemical variations have also been observed among all the paragenetic minerals of each district. The thermal variations may be as a result of variations in the geothermal gradient accompanying continental rifting from one district to the other. The variations in the chemistry between the Lower Benue and the Upper Benue paragenic minerals may be as a result of the distinct lithological differences across the Benue Trough.

Effect of temperature and O-ring gland finish on sealing ability of Viton V747-75

NASA Technical Reports Server (NTRS)

Lach, Cynthia L.

1993-01-01

As a part of the redesign project of the Space Shuttle solid rocket motor (SRM) following the Challenger accident, the field joint was redesigned to minimize the relative joint motion caused by internal motor pressurization during ignition. The O-ring seals and glands for the field joint were designed both to accommodate structural deflections and to promote pressure-assisted sealing. Tests were conducted in various face seal fixtures to evaluate the ability of Viton V747-75 O-rings to seal for a range of temperatures and surface finishes of the redesigned O-ring gland. The effect of surface finish on the sealing performance and wear characteristics of the O-rings was evaluated during simulated launch conditions that included low-frequency vibrations, gap openings, and rapid pressurizations. The effect of contamination on the sealing performance was also investigated. The O-rings sealed throughout the 75 deg F leak check test and for the seal tests from 50 deg F to 120 deg F for the range of surface finishes investigated. Although abrasions were found in the O-rings from pressurization against the rougher finishes, these abrasions were not detrimental to sealing. Below 50 deg F, Viton V747-75 O-rings were insufficiently resilient to track the test gap opening.

Characteristics of Crushing Energy and Fractal of Magnetite Ore under Uniaxial Compression

NASA Astrophysics Data System (ADS)

Gao, F.; Gan, D. Q.; Zhang, Y. B.

2018-03-01

The crushing mechanism of magnetite ore is a critical theoretical problem on the controlling of energy dissipation and machine crushing quality in ore material processing. Uniaxial crushing tests were carried out to research the deformation mechanism and the laws of the energy evolution, based on which the crushing mechanism of magnetite ore was explored. The compaction stage and plasticity and damage stage are two main compression deformation stages, the main transitional forms from inner damage to fracture are plastic deformation and stick-slip. In the process of crushing, plasticity and damage stage is the key link on energy absorption for that the specimen tends to saturate energy state approaching to the peak stress. The characteristics of specimen deformation and energy dissipation can synthetically reply the state of existed defects inner raw magnetite ore and the damage process during loading period. The fast releasing of elastic energy and the work done by the press machine commonly make raw magnetite ore thoroughly broken after peak stress. Magnetite ore fragments have statistical self-similarity and size threshold of fractal characteristics under uniaxial squeezing crushing. The larger ratio of releasable elastic energy and dissipation energy and the faster energy change rate is the better fractal properties and crushing quality magnetite ore has under uniaxial crushing.

The physical hydrology of magmatic-hydrothermal systems: High-resolution 18O records of magmatic-meteoric water interaction from the Yankee Lode tin deposit (Mole Granite, Australia)

NASA Astrophysics Data System (ADS)

Fekete, Szandra; Weis, Philipp; Driesner, Thomas; Heinrich, Christoph A.; Baumgartner, Lukas; Bouvier, Anne-Sophie

2016-04-01

Magmatic-hydrothermal ore deposits are important economic Cu, Au, Mo and Sn resources (Sillitoe, 2010, Kesler, 1994). The ore formation is a result of superimposed enrichment processes and metals can precipitate due to fluid-rock interaction and/or temperature drop caused by convection or mixing with meteoric fluid (Heinrich and Candela 2014). Microthermometry and LA-ICP MS trace element analyses of fluid inclusions of a well-characterized quartz sample from the Yankee Lode quartz-cassiterite vein deposit (Mole Granite, Australia) suggest that tin precipitation was driven by dilution of hot magmatic water by meteoric fluids (Audétat et al.1998). High resolution in situ oxygen isotope measurements of quartz have the potential to detect changing fluid sources during the evolution of a hydrothermal system. We analyzed the euhedral growth zones of this previously well-studied quartz sample. Growth temperatures are provided by Audétat et al. (1998) and Audétat (1999). Calculated δ 18O values of the quartz- and/or cassiterite-precipitating fluid show significant variability through the zoned crystal. The first and second quartz generations (Q1 and Q2) were precipitated from a fluid of magmatic isotopic composition with δ 18O values of ˜ 8 - 10 ‰. δ 18O values of Q3- and tourmaline-precipitating fluids show a transition from magmatic δ 18O values of ˜ 8 ‰ to ˜ -5 ‰. The outermost quartz-chlorite-muscovite zone was precipitated from a fluid with a significant meteoric water component reflected by very light δ 18O values of about -15 ‰ which is consistent with values found by previous studies (Sun and Eadington, 1987) using conventional O-isotope analysis of veins in the distal halo of the granite intrusion. Intense incursion of meteoric water during Q3 precipitation (light δ 18O values) agrees with the main ore formation event, though the first occurrence of cassiterite is linked to Q2 precipitating fluid with magmatic-like isotope signature. This apparent discrepancy can be explained by the presence of a fluid of meteoric origin that was isotopically equilibrated with a hot, but already solidified and fractured granitic intrusion under rock-dominated conditions prior their transfer to the cold ore deposition site (Heinrich, 1990). Conversely, in porphyry copper systems meteoric fluid incursion has been assumed to participate in formation of peripheral or post-mineralization processes (Bowman et al., 1987; Sillitoe, 2010; Williams-Jones and Migdisov, 2014). However, recent numerical simulations of porphyry copper systems identify a significant role of meteoric fluids for the enrichment process, providing a cooling mechanism for metal-rich fluids expelled from an upper crustal magma chamber (Weis et al. 2012, Weis 2015). Furthermore, new petrographic and fluid inclusion work of ore-mineralized quartz veins (Landtwing et al., 2010; Stefanova et al., 2014) indicates lower (˜ 450r{ }C) than magmatic fluid temperatures for copper precipitation. Given that the Yankee Lode study validated the capability of high resolution, in situ δ 18O analysis to trace meteoric water incursion, we will apply this method to hydrothermal quartz samples from two significant porphyry copper deposits (Bingham Canyon, USA and Elatsite, Bulgaria). By this we intend to better constrain a potential role of meteoric water incursion in porphyry copper ore precipitation. REFERENCES Audétat, A., Günther, D., Heinrich, C. A. 1998: Formation of a Magmatic-Hydrothermal Ore Deposit: Insights with LA-ICP-MS Analysis of Fluid Inclusions: Science, 279, 2091-2094. Audétat, A. 1999: The magmatic-hydrothermal evolution of the Sn/W-mineralized Mole Granite (Eastern Australia): PhD Thesis, 211. Bowman, J. R., Parry, W. T., Kropp, W. P., and Kruer, S. A., 1987: Chemical and isotopic evolution of hydrothermal solutions at Bingham, Utah: Economic Geology, 82, 395-428. Heinrich, C.A. 1990: The Chemistry of Hydrothermal Tin(-Tungsten) Ore Deposition: Economic Geology, 85, 457-481. Heinrich, C. A., and Candela, P. A. 2014: 13.1 - Fluids and Ore Formation in the Earth's Crust, in Holland, H. D., and Turekian, K. K., eds., Treatise on Geochemistry (Second Edition): Oxford, Elsevier, 1-28. Kesler, S. E., 1994: Mineral Resources, economics and the environment, New York, McMillan, 391. Sillitoe, R. H., 2010: Porphyry copper systems: Economic Geology (Invited Special Paper), 105, 3-41. Sun, S. and Eadington, J. 1987: Oxygen Isotope Evidence for the Mixing of Magmatic and Meteoric Waters during Tin Mineralization in the Mole Granite, New South Wales, Australia: Economic Geology, 82, 43-52. Weis, P., Driesner, T., & Heinrich, C.A. 2012: Porphyry-Copper Ore Shells Form At Stable Pressure Temperature Fronts Within Dynamic Fluid Plumes: Science, 338, 1613-1616. Williams-Jones, A. E., and Migdisov, A. A., 2014: Experimental Constraints on the Transport and Deposition of Metals in Ore-Forming Hydrothermal Systems: Economic Geology, Special Publication, 18, 77-95.

SNR improvement for hyperspectral application using frame and pixel binning

NASA Astrophysics Data System (ADS)

Rehman, Sami Ur; Kumar, Ankush; Banerjee, Arup

2016-05-01

Hyperspectral imaging spectrometer systems are increasingly being used in the field of remote sensing for variety of civilian and military applications. The ability of such instruments in discriminating finer spectral features along with improved spatial and radiometric performance have made such instruments a powerful tool in the field of remote sensing. Design and development of spaceborne hyper spectral imaging spectrometers poses lot of technological challenges in terms of optics, dispersion element, detectors, electronics and mechanical systems. The main factors that define the type of detectors are the spectral region, SNR, dynamic range, pixel size, number of pixels, frame rate, operating temperature etc. Detectors with higher quantum efficiency and higher well depth are the preferred choice for such applications. CCD based Si detectors serves the requirement of high well depth for VNIR band spectrometers but suffers from smear. Smear can be controlled by using CMOS detectors. Si CMOS detectors with large format arrays are available. These detectors generally have smaller pitch and low well depth. Binning technique can be used with available CMOS detectors to meet the large swath, higher resolution and high SNR requirements. Availability of larger dwell time of satellite can be used to bin multiple frames to increase the signal collection even with lesser well depth detectors and ultimately increase the SNR. Lab measurements reveal that SNR improvement by frame binning is more in comparison to pixel binning. Effect of pixel binning as compared to the frame binning will be discussed and degradation of SNR as compared to theoretical value for pixel binning will be analyzed.

Generalized index for spatial data sets as a measure of complete spatial randomness

NASA Astrophysics Data System (ADS)

Hackett-Jones, Emily J.; Davies, Kale J.; Binder, Benjamin J.; Landman, Kerry A.

2012-06-01

Spatial data sets, generated from a wide range of physical systems can be analyzed by counting the number of objects in a set of bins. Previous work has been limited to equal-sized bins, which are inappropriate for some domains (e.g., circular). We consider a nonequal size bin configuration whereby overlapping or nonoverlapping bins cover the domain. A generalized index, defined in terms of a variance between bin counts, is developed to indicate whether or not a spatial data set, generated from exclusion or nonexclusion processes, is at the complete spatial randomness (CSR) state. Limiting values of the index are determined. Using examples, we investigate trends in the generalized index as a function of density and compare the results with those using equal size bins. The smallest bin size must be much larger than the mean size of the objects. We can determine whether a spatial data set is at the CSR state or not by comparing the values of a generalized index for different bin configurations—the values will be approximately the same if the data is at the CSR state, while the values will differ if the data set is not at the CSR state. In general, the generalized index is lower than the limiting value of the index, since objects do not have access to the entire region due to blocking by other objects. These methods are applied to two applications: (i) spatial data sets generated from a cellular automata model of cell aggregation in the enteric nervous system and (ii) a known plant data distribution.

Meta-analysis of 32 genome-wide linkage studies of schizophrenia

PubMed Central

Ng, MYM; Levinson, DF; Faraone, SV; Suarez, BK; DeLisi, LE; Arinami, T; Riley, B; Paunio, T; Pulver, AE; Irmansyah; Holmans, PA; Escamilla, M; Wildenauer, DB; Williams, NM; Laurent, C; Mowry, BJ; Brzustowicz, LM; Maziade, M; Sklar, P; Garver, DL; Abecasis, GR; Lerer, B; Fallin, MD; Gurling, HMD; Gejman, PV; Lindholm, E; Moises, HW; Byerley, W; Wijsman, EM; Forabosco, P; Tsuang, MT; Hwu, H-G; Okazaki, Y; Kendler, KS; Wormley, B; Fanous, A; Walsh, D; O’Neill, FA; Peltonen, L; Nestadt, G; Lasseter, VK; Liang, KY; Papadimitriou, GM; Dikeos, DG; Schwab, SG; Owen, MJ; O’Donovan, MC; Norton, N; Hare, E; Raventos, H; Nicolini, H; Albus, M; Maier, W; Nimgaonkar, VL; Terenius, L; Mallet, J; Jay, M; Godard, S; Nertney, D; Alexander, M; Crowe, RR; Silverman, JM; Bassett, AS; Roy, M-A; Mérette, C; Pato, CN; Pato, MT; Roos, J Louw; Kohn, Y; Amann-Zalcenstein, D; Kalsi, G; McQuillin, A; Curtis, D; Brynjolfson, J; Sigmundsson, T; Petursson, H; Sanders, AR; Duan, J; Jazin, E; Myles-Worsley, M; Karayiorgou, M; Lewis, CM

2009-01-01

A genome scan meta-analysis (GSMA) was carried out on 32 independent genome-wide linkage scan analyses that included 3255 pedigrees with 7413 genotyped cases affected with schizophrenia (SCZ) or related disorders. The primary GSMA divided the autosomes into 120 bins, rank-ordered the bins within each study according to the most positive linkage result in each bin, summed these ranks (weighted for study size) for each bin across studies and determined the empirical probability of a given summed rank (PSR) by simulation. Suggestive evidence for linkage was observed in two single bins, on chromosomes 5q (142-168 Mb) and 2q (103-134 Mb). Genome-wide evidence for linkage was detected on chromosome 2q (119-152 Mb) when bin boundaries were shifted to the middle of the previous bins. The primary analysis met empirical criteria for ‘aggregate’ genome-wide significance, indicating that some or all of 10 bins are likely to contain loci linked to SCZ, including regions of chromosomes 1, 2q, 3q, 4q, 5q, 8p and 10q. In a secondary analysis of 22 studies of European-ancestry samples, suggestive evidence for linkage was observed on chromosome 8p (16-33 Mb). Although the newer genome-wide association methodology has greater power to detect weak associations to single common DNA sequence variants, linkage analysis can detect diverse genetic effects that segregate in families, including multiple rare variants within one locus or several weakly associated loci in the same region. Therefore, the regions supported by this meta-analysis deserve close attention in future studies. PMID:19349958

Altered Splicing of the BIN1 Muscle-Specific Exon in Humans and Dogs with Highly Progressive Centronuclear Myopathy

PubMed Central

Böhm, Johann; Vasli, Nasim; Maurer, Marie; Cowling, Belinda; Shelton, G. Diane; Kress, Wolfram; Toussaint, Anne; Prokic, Ivana; Schara, Ulrike; Anderson, Thomas James; Weis, Joachim; Tiret, Laurent; Laporte, Jocelyn

2013-01-01

Amphiphysin 2, encoded by BIN1, is a key factor for membrane sensing and remodelling in different cell types. Homozygous BIN1 mutations in ubiquitously expressed exons are associated with autosomal recessive centronuclear myopathy (CNM), a mildly progressive muscle disorder typically showing abnormal nuclear centralization on biopsies. In addition, misregulation of BIN1 splicing partially accounts for the muscle defects in myotonic dystrophy (DM). However, the muscle-specific function of amphiphysin 2 and its pathogenicity in both muscle disorders are not well understood. In this study we identified and characterized the first mutation affecting the splicing of the muscle-specific BIN1 exon 11 in a consanguineous family with rapidly progressive and ultimately fatal centronuclear myopathy. In parallel, we discovered a mutation in the same BIN1 exon 11 acceptor splice site as the genetic cause of the canine Inherited Myopathy of Great Danes (IMGD). Analysis of RNA from patient muscle demonstrated complete skipping of exon 11 and BIN1 constructs without exon 11 were unable to promote membrane tubulation in differentiated myotubes. Comparative immunofluorescence and ultrastructural analyses of patient and canine biopsies revealed common structural defects, emphasizing the importance of amphiphysin 2 in membrane remodelling and maintenance of the skeletal muscle triad. Our data demonstrate that the alteration of the muscle-specific function of amphiphysin 2 is a common pathomechanism for centronuclear myopathy, myotonic dystrophy, and IMGD. The IMGD dog is the first faithful model for human BIN1-related CNM and represents a mammalian model available for preclinical trials of potential therapies. PMID:23754947

Nitrile/Buna N Material Failure Assessment for an O-Ring used on the Gaseous Hydrogen Flow Control Valve (FCV) of the Space Shuttle Main Engine

NASA Technical Reports Server (NTRS)

Wingard, Doug

2006-01-01

After the rollout of Space Shuttle Discovery in April 2005 in preparation for return-to-flight, there was a failure of the Orbiter (OV-103) helium signature leak test in the gaseous hydrogen (GH2) system. Leakage was attributed to the Flow Control Valve (FCV) in Main Engine 3. The FCV determined to be the source of the leak for OV-103 is designated as LV-58. The nitrile/Buna N rubber O-ring seal was removed from LV-58, and failure analysis indicated radial cracks providing leak paths in one quadrant. Cracks were eventually found in 6 of 9 FCV O-rings among the three Shuttle Orbiters, though none were as severe as those for LV-58, OV-103. Testing by EM10 at MSFC on all 9 FCV O- rings included: laser dimensional, Shore A hardness and properties from a dynamic mechanical analyzer (DMA) and an Instron tensile machine. The following test data was obtained on the cracked quadrant of the LV-58, OV-103 O-ring: (1) the estimated compression set was only 9.5%, compared to none for the rest of the O-ring; (2) Shore A hardness for the O.D. was higher by almost 4 durometer points than for the rest of the O-ring; and (3) DMA data showed that the storage/elastic modulus E was almost 25% lower than for the rest of the O-ring. Of the 8 FCV O-rings tested on an Instron, 4 yielded tensile strengths that were below the MIL spec requirement of 1350 psi-a likely influence of rubber cracking. Comparisons were made between values of modulus determined by DNA (elastic) and Instron (Young s). Each nitrile/Buna N O-ring used in the FCV conforms to the MIL-P-25732C specification. A number of such O-rings taken from shelf storage at MSFC and Kennedy Space Center (KSC) were used to generate a reference curve of DMA glass transition temperature (Tg) vs. shelf storage time ranging from 8 to 26 years. A similar reference curve of TGA onset temperature (of rubber weight loss) vs. shelf storage time was also generated. The DMA and TGA data for the used FCV O-rings were compared to the reference curves. Correlations were also made between the DMA modulus (at 22 C) and Shore A hardness for all 9 of the FCV O-rings used among the three Shuttle Orbiters. The radial cracking in the FCV O-rings was determined to be due to ozone attack, as nitrile/Buna N rubber is susceptible to such attack. Nitrile/Buna N material under MIL-P25732C should be used in a hydraulic fluid environment to help protect it from cracking. However, the FCV O-rings were used in an air only environment. The FCV design has as much as a 9-mil gap that allows the O.D. of the O-ring to be directly exposed to ozone, pressurized air and some elevated temperatures, accelerating the weathering process that leads to O-ring cracking. Space Shuttle flights will likely not continue past 2010. Therefore, Shuttle management decided to continue using the nitrile/Buna N material for the FCVs, but have each O-ring replaced after 3 years to minimize any chances for crack initiation.

Compositional and isotopic heterogeneities in the Neo-Tethyan upper mantle recorded by coexisting Al-rich and Cr-rich chromitites in the Purang peridotite massif, SW Tibet (China)

NASA Astrophysics Data System (ADS)

Xiong, Fahui; Yang, Jingsui; Xu, Xiangzhen; Kapsiotis, Argyrios; Hao, Xiaolin; Liu, Zhao

2018-06-01

The Purang harzburgite massif in SW Tibet (China) hosts abundant chrome ore deposits. Ores consist of 20 to >95% modal chromian spinel (Cr-spinel) with mylonitic fabric in imbricate shaped pods. The composition of Cr-spinel in these ores ranges from Al-rich [Cr#Sp or Cr/(Cr + Al) × 100 = 47.60-57.56] to Cr-rich (Cr#Sp: 62.55-79.57). Bulk platinum-group element (PGE) contents of chromitites are also highly variable ranging from 17.5 ppb to ∼2.5 ppm. Both metallurgical and refractory chromitites show a general enrichment in the IPGE (Os, Ir and Ru) with respect to the PPGE (Rh, Pt and Pd), resulting mostly in right-sloping primitive mantle (PM)-normalized PGE profiles. The platinum-group mineral (PGM) assemblages of both chromitite types are dominated by heterogeneously distributed, euhedral Os-bearing laurite inclusions in Cr-spinel. The Purang chromitites have quite inhomogeneous 187Os/188Os ratios (0.12289-0.13194) that are within the range of those reported for mantle-hosted chromitites from other peridotite massifs. Geochemical calculations demonstrate that the parental melts of high-Cr chromitites were boninitic, whereas those of high-Al chromitites had an arc-type tholeiitic affinity. Chromite crystallization was most likely stimulated by changes in magma compositions due to melt-peridotite interaction, leading to the establishment of a heterogeneous physicochemical environment during the early crystallization of the PGM. The highly variable PGE contents, inhomogeneous Os-isotopic compositions and varying Cr#Sp ratios of these chromitites imply a polygenetic origin for them from spatially distinct melt inputs. The generally low γOs values (<1) of chromitites indicate that their parental melts originated within different sections of a heterogeneously depleted mantle source region. These melts were most likely produced in the mantle wedge above a downgoing lithospheric slab.

The El Teniente porphyry Cu-Mo deposit from a hydrothermal rutile perspective

NASA Astrophysics Data System (ADS)

Rabbia, Osvaldo M.; Hernández, Laura B.; French, David H.; King, Robert W.; Ayers, John C.

2009-11-01

Mineralogical, textural, and chemical analyses (EPMA and PIXE) of hydrothermal rutile in the El Teniente porphyry Cu-Mo deposit help to better constrain ore formation processes. Rutile formed from igneous Ti-rich phases (sphene, biotite, Ti-magnetite, and ilmenite) by re-equilibration and/or breakdown under hydrothermal conditions at temperatures ranging between 400°C and 700°C. Most rutile nucleate and grow at the original textural position of its Ti-rich igneous parent mineral phase. The distribution of Mo content in rutile indicates that low-temperature (˜400-550°C), Mo-poor rutile (5.4 ± 1.1 ppm) is dominantly in the Mo-rich mafic wallrocks (high-grade ore), while high-temperature (˜550-700°C), Mo-rich rutile (186 ± 20 ppm) is found in the Mo-poor felsic porphyries (low-grade ore). Rutile from late dacite ring dikes is a notable exception to this distribution pattern. The Sb content in rutile from the high-temperature potassic core of the deposit to its low-temperature propylitic fringe remains relatively constant (35 ± 3 ppm). Temperature and Mo content of the hydrothermal fluids in addition to Mo/Ti ratio, modal abundance and stability of Ti-rich parental phases are key factors constraining Mo content and provenance in high-temperature (≥550°C) rutile. The initial Mo content of parent mineral phases is controlled by melt composition and oxygen fugacity as well as timing and efficiency of fluid-melt separation. Enhanced reduction of SO2-rich fluids and sulfide deposition in the Fe-rich mafic wallrocks influences the low-temperature (≤550°C) rutile chemistry. The data are consistent with a model of fluid circulation of hot (>550°C), oxidized (ƒO2 ≥ NNO + 1.3), SO2-rich and Mo-bearing fluids, likely exsolved from deeper crystallizing parts of the porphyry system and fluxed through the upper dacite porphyries and related structures, with metal deposition dominantly in the Fe-rich mafic wallrocks.

Large scale magmatic event, magnetic anomalies and ore exploration in northern Norway

NASA Astrophysics Data System (ADS)

Pastore, Z.; Church, N. S.; ter Maat, G. W.; Michels, A.; McEnroe, S. A.; Fichler, C.; Larsen, R. B.

2016-12-01

More than 17000 km3of igneous melts intruded into the deep crust at ca. 560-580 Ma and formed the Seiland Igneous Province (SIP), the largest complex of mafic and ultramafic intrusions in northern Fennoscandia. The original emplacement of the SIP is matter of current discussion. The SIP is now located within the Kalak Nappe Complex (KNC), a part of the Middle Allochthon of the North Norwegian Caledonides. The province is believed to represent a cross section of the deep plumbing system of a large igneous province and it is known for its layered intrusions sharing geological features with large ore-forming exploration provinces. In this study we investigate one of the four major ultramafic complexes of the province, the Reinfjord Complex. This was emplaced during three magmatic events in a time span of 4 Ma, and consists in a cylindrically zoned complex with a slightly younger dunite core (Central Series) surrounded by wehrlite and lherzolite dominated series (Upper and Lower Layered Series). Sulphides are present throughout the complex, and an electromagnetic survey identified a Ni-Cu-and a PGE reef deposit within the dunite, 100 meters below the surface. This discovery increased the ore potential of the complex and subsequently 4 deep drill cores were made. High-resolution magnetic helicopter survey was later followed up with ground magnetic and gravity surveys. Extensive sampling of surface rocks and drill cores were made to measure the rock-magnetic and physical properties of the samples and to explore the subsurface structure of the complex. Here, we developed a magnetic model for the Reinfjord complex integrating petrophysical data from both oriented surface samples and from the deep drill cores, with the new ground magnetic, and helicopter data (SkyTEM survey). A 3D model of the geometry of the ultramafic intrusion is presented and a refinement of the geological interpretation of the Reinfjord ultramafic intrusion.

Uncertainty in Modeling Dust Mass Balance and Radiative Forcing from Size Parameterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Chun; Chen, Siyu; Leung, Lai-Yung R.

2013-11-05

This study examines the uncertainties in simulating mass balance and radiative forcing of mineral dust due to biases in the aerosol size parameterization. Simulations are conducted quasi-globally (180oW-180oE and 60oS-70oN) using the WRF24 Chem model with three different approaches to represent aerosol size distribution (8-bin, 4-bin, and 3-mode). The biases in the 3-mode or 4-bin approaches against a relatively more accurate 8-bin approach in simulating dust mass balance and radiative forcing are identified. Compared to the 8-bin approach, the 4-bin approach simulates similar but coarser size distributions of dust particles in the atmosphere, while the 3-mode pproach retains more finemore » dust particles but fewer coarse dust particles due to its prescribed og of each mode. Although the 3-mode approach yields up to 10 days longer dust mass lifetime over the remote oceanic regions than the 8-bin approach, the three size approaches produce similar dust mass lifetime (3.2 days to 3.5 days) on quasi-global average, reflecting that the global dust mass lifetime is mainly determined by the dust mass lifetime near the dust source regions. With the same global dust emission (~6000 Tg yr-1), the 8-bin approach produces a dust mass loading of 39 Tg, while the 4-bin and 3-mode approaches produce 3% (40.2 Tg) and 25% (49.1 Tg) higher dust mass loading, respectively. The difference in dust mass loading between the 8-bin approach and the 4-bin or 3-mode approaches has large spatial variations, with generally smaller relative difference (<10%) near the surface over the dust source regions. The three size approaches also result in significantly different dry and wet deposition fluxes and number concentrations of dust. The difference in dust aerosol optical depth (AOD) (a factor of 3) among the three size approaches is much larger than their difference (25%) in dust mass loading. Compared to the 8-bin approach, the 4-bin approach yields stronger dust absorptivity, while the 3-mode approach yields weaker dust absorptivity. Overall, on quasi-global average, the three size parameterizations result in a significant difference of a factor of 2~3 in dust surface cooling (-1.02~-2.87 W m-2) and atmospheric warming (0.39~0.96 W m-2) and in a tremendous difference of a factor of ~10 in dust TOA cooling (-0.24~-2.20 W m-2). An uncertainty of a factor of 2 is quantified in dust emission estimation due to the different size parameterizations. This study also highlights the uncertainties in modeling dust mass and number loading, deposition fluxes, and radiative forcing resulting from different size parameterizations, and motivates further investigation of the impact of size parameterizations on modeling dust impacts on air quality, climate, and ecosystem.« less

Geophysical data collected from the St. Clair River between Michigan and Ontario, Canada (2008-016-FA)

USGS Publications Warehouse

Denny, Jane F.; Foster, D.S.; Worley, C.R.; Irwin, Barry J.

2011-01-01

In 2008, the U.S. Geological Survey (USGS), Woods Hole Coastal and Marine Science Center (WHCMSC), in cooperation with the U.S. Army Corps of Engineers conducted a geophysical and sampling survey of the riverbed of the Upper St. Clair River between Port Huron, Mich., and Sarnia, Ontario, Canada. The objectives were to define the Quaternary geologic framework of the riverbed of the St. Clair River to evaluate the relationship between morphologic change of the riverbed and underlying stratigraphy. This report presents the geophysical and sample data collected from the St. Clair River, May 29-June 6, 2008, as part of the International Upper Great Lakes Study, a 5-year project funded by the International Joint Commission of the United States and Canada to examine whether physical changes in the St. Clair River are affecting water levels within upper Great Lakes, to assess regulation plans for outflows from Lake Superior, and to examine the potential effect of climate change on the Great Lakes water levels (http://www.iugls.org). This document makes available the data that were used in a separate report, U.S. Geological Survey Open-File Report 2009-1137, which detailed the interpretations of the Quaternary geologic framework of the region. This report includes a description of the high-resolution acoustic and sediment-sampling systems that were used to map the morphology, surficial sediment distribution, and underlying geology of the Upper St. Clair River during USGS field activity 2008-016-FA (http://quashnet.er.usgs.gov/cgi-bin/datasource/public_ds_info.pl?fa=2008-016-FA). Video and photographs of the riverbed were also collected and are included in this data release. Future analyses will be focused on substrate erosion and its effects on river-channel morphology and geometry. Ultimately, the International Upper Great Lakes Study will attempt to determine where physical changes in the St. Clair River affect water flow and, subsequently, water levels in the Upper Great Lakes.

Low-Temperature Effects on the Design and Performance of Composting of Explosives-Contaminated Soils

DTIC Science & Technology

1991-03-01

7 7. Aerated bins used in field composting tests on dairy manure ............................. 10 8. Typical temperature developed...during bin compostiag of dairy manure under conditions of constant airflow and optimum moisture ................. 10 9. Effect of agitation on the...temperature profile during bin composting of dairy manure

16 CFR 1301.6 - Test conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Test conditions. 1301.6 Section 1301.6... UNSTABLE REFUSE BINS § 1301.6 Test conditions. (a) The refuse bin shall be empty and have its lids or covers in a position which would most adversely affect the stability of the bin when tested. (b) The...

16 CFR 1301.6 - Test conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Test conditions. 1301.6 Section 1301.6... UNSTABLE REFUSE BINS § 1301.6 Test conditions. (a) The refuse bin shall be empty and have its lids or covers in a position which would most adversely affect the stability of the bin when tested. (b) The...

16 CFR 1301.6 - Test conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test conditions. 1301.6 Section 1301.6... UNSTABLE REFUSE BINS § 1301.6 Test conditions. (a) The refuse bin shall be empty and have its lids or covers in a position which would most adversely affect the stability of the bin when tested. (b) The...

90. Photographic copy of plan of bins, section of boot, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

90. Photographic copy of plan of bins, section of boot, and photograph of construction originally published in Plans of Grain Elevators (Chicago; Grain Dealers Journal, 1918), p.53. PLAN OF BINS; SECTION OF BOOT; VIEW OF CONSTRUCTION LOOKING NORTHWEST - Northwestern Consolidated Elevator "A", 119 Fifth Avenue South, Minneapolis, Hennepin County, MN

Increasing donations to supermarket food-bank bins using proximal prompts.

PubMed

Farrimond, Samantha J; Leland, Louis S

2006-01-01

There has been little research into interventions to increase participation in donating items to food-bank bins. In New Zealand, there has been an increased demand from food banks (Stewart, 2002). This study demonstrated that point-of-sale prompts can be an effective method of increasing donations to a supermarket food-bank bin.

Shapes on a plane: Evaluating the impact of projection distortion on spatial binning

USGS Publications Warehouse

Battersby, Sarah E.; Strebe, Daniel “daan”; Finn, Michael P.

2017-01-01

One method for working with large, dense sets of spatial point data is to aggregate the measure of the data into polygonal containers, such as political boundaries, or into regular spatial bins such as triangles, squares, or hexagons. When mapping these aggregations, the map projection must inevitably distort relationships. This distortion can impact the reader’s ability to compare count and density measures across the map. Spatial binning, particularly via hexagons, is becoming a popular technique for displaying aggregate measures of point data sets. Increasingly, we see questionable use of the technique without attendant discussion of its hazards. In this work, we discuss when and why spatial binning works and how mapmakers can better understand the limitations caused by distortion from projecting to the plane. We introduce equations for evaluating distortion’s impact on one common projection (Web Mercator) and discuss how the methods used generalize to other projections. While we focus on hexagonal binning, these same considerations affect spatial bins of any shape, and more generally, any analysis of geographic data performed in planar space.

Fluid inclusion, rare earth element geochemistry, and isotopic characteristics of the eastern ore zone of the Baiyangping polymetallic Ore district, northwestern Yunnan Province, China

NASA Astrophysics Data System (ADS)

Feng, Caixia; Bi, Xianwu; Liu, Shen; Hu, Ruizhong

2014-05-01

The Baiyangping Cu-Ag polymetallic ore district is located in the northern part of the Lanping-Simao foreland fold belt, which lies between the Jinshajiang-Ailaoshan and Lancangjiang faults in western Yunnan Province, China. The source of ore-forming fluids and materials within the eastern ore zone were investigated using fluid inclusion, rare earth element (REE), and isotopic (C, O, and S) analyses undertaken on sulfides, gangue minerals, wall rocks, and ores formed during the hydrothermal stage of mineralization. These analyses indicate: (1) The presence of five types of fluid inclusion, which contain various combinations of liquid (l) and vapor (v) phases at room temperature: (a) H2O (l), (b) H2O (l) + H2O (v), (c) H2O (v), (d) CmHn (v), and (e) H2O (l) + CO2 (l), sometimes with CO2 (v). These inclusions have salinities of 1.4-19.9 wt.% NaCl equivalents, with two modes at approximately 5-10 and 16-21 wt.% NaCl equivalent, and homogenization temperatures between 101 °C and 295 °C. Five components were identified in fluid inclusions using Raman microspectrometry: H2O, dolomite, calcite, CH4, and N2. (2) Calcite, dolomitized limestone, and dolomite contain total REE concentrations of 3.10-38.93 ppm, whereas wall rocks and ores contain REE concentrations of 1.21-196 ppm. Dolomitized limestone, dolomite, wall rock, and ore samples have similar chondrite-normalized REE patterns, with ores in the Huachangshan, Xiaquwu, and Dongzhiyan ore blocks having large negative δCe and δEu anomalies, which may be indicative of a change in redox conditions during fluid ascent, migration, and/or cooling. (3) δ34S values for sphalerite, galena, pyrite, and tetrahedrite sulfide samples range from -7.3‰ to 2.1‰, a wide range that indicates multiple sulfur sources. The basin contains numerous sources of S, and deriving S from a mixture of these sources could have yielded these near-zero values, either by mixing of S from different sources, or by changes in the geological conditions of seawater sulfate reduction to sulfur. (4) The C-O isotopic analyses yield δ13C values from ca. zero to -10‰, and a wider range of δ18O values from ca. +6 to +24‰, suggestive of mixing between mantle-derived magma and marine carbonate sources during the evolution of ore-forming fluids, although potential contributions from organic carbon and basinal brine sources should also be considered. These data indicate that ore-forming fluids were derived from a mixture of organism, basinal brine, and mantle-derived magma sources, and as such, the eastern ore zone of the Baiyangping polymetallic ore deposit should be classified as a “Lanping-type” ore deposit.

SIXTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

2011-08-31

A series of experiments to monitor the aging performance of Viton{reg_sign} GLT O-rings used in the Model 9975 package has been ongoing for seven years at the Savannah River National Laboratory. Seventy tests using mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested periodically to determine if they meet the criterion of leak-tightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues formore » 33 GLT O-ring fixtures at 200-300 F. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 F and higher temperatures, and in 7 fixtures aging at 300 F. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 41-60 months, which is still bounding to O-ring temperatures during storage in K-Area Complex (KAC). Based on expectations that the fixtures aging at 200 F will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging within the past year at an intermediate temperature of 270 F, with hopes that they may leak before the 200 F fixtures. High temperature aging continues for 6 GLT-S O-ring fixtures at 200-300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200-300 F for up to 26 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the Orings displayed a compression set ranging from 51-96%. This is greater than seen to date for packages inspected during KAC field surveillance (24% average). For GLT O-rings, separate service life estimates have been made based on the O-ring fixture leak test data and based on compression stress relaxation (CSR) data. These two predictive models show reasonable agreement at higher temperatures (350-400 F). However, at 300 F, the room temperature leak test failures to date experienced longer aging times than predicted by the CSR-based model. This suggests that extrapolations of the CSR model predictions to temperatures below 300 F will provide a conservative prediction of service life relative to the leak rate criterion. Leak test failure data at lower temperatures are needed to verify this apparent trend. Insufficient failure data exist currently to perform a similar comparison for GLT-S O-rings. Aging and periodic leak testing will continue for the remaining fixtures.« less

NINTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

2014-08-06

A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. One approach has been to periodically evaluate the leak performance of O-rings being aged in mock-up 9975 Primary Containment Vessels (PCVs) at elevated temperatures. Other methods such as compression-stress relaxation (CSR) tests and field surveillance are also on-going to evaluate O-ring behavior. Seventy tests using PCV mock-ups were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determinemore » if they continue to meet the leak-tightness criterion defined in ANSI standard N14.5-97. Due to material substitution, fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. High temperature aging continues for 23 GLT O-ring fixtures at 200 – 270 ºF. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The earliest 300 °F GLT O-ring fixture failure was observed at 34 months. The remaining GLT O-ring fixtures aging at 300 ºF have been retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 72 - 96 months, which bounds O-ring temperatures anticipated during storage in K-Area Complex (KAC). Based on expectations that the 200 ºF fixtures will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging in 2011 at 270 ºF, with hopes that they may reach a failure condition before the 200 ºF fixtures, thus providing additional time to failure data. High temperature aging continues for 6 GLT-S O-ring fixtures at 200 – 300 ºF. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 ºF. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 - 300 ºF for 54 - 57 months. No additional O-ring failures have been observed since the last interim report was issued. Aging and periodic leak testing will continue for the remaining PCV fixtures. Additional irradiation of several fixtures is recommended to maintain a balance between thermal and radiation exposures similar to that experienced in storage, and to show the degree of consistency of radiation response between GLT and GLT-S O-rings.« less

An 18-ps TDC using timing adjustment and bin realignment methods in a Cyclone-IV FPGA

NASA Astrophysics Data System (ADS)

Cao, Guiping; Xia, Haojie; Dong, Ning

2018-05-01

The method commonly used to produce a field-programmable gate array (FPGA)-based time-to-digital converter (TDC) creates a tapped delay line (TDL) for time interpolation to yield high time precision. We conduct timing adjustment and bin realignment to implement a TDC in the Altera Cyclone-IV FPGA. The former tunes the carry look-up table (LUT) cell delay by changing the LUT's function through low-level primitives according to timing analysis results, while the latter realigns bins according to the timing result obtained by timing adjustment so as to create a uniform TDL with bins of equivalent width. The differential nonlinearity and time resolution can be improved by realigning the bins. After calibration, the TDC has a 18 ps root-mean-square timing resolution and a 45 ps least-significant bit resolution.

Political orientation moderates worldview defense in response to Osama bin Laden’s death

PubMed Central

Chopik, William J.; Konrath, Sara H.

2016-01-01

The current study examines Americans’ psychological responses to Osama bin Laden’s death. We tracked changes in how different participants responded to dissimilar others from the night of bin Laden’s death for five weeks. Liberal participants reported lower worldview defense (i.e., a defensive reaction to uphold one’s cultural worldview) immediately after bin Laden’s death but then returned to similar levels as their conservative counterparts over time. Conservative participants reported greater worldview defense during each point of the study and did not significantly change over time. These temporal differences between liberals and conservatives were only present in the year of bin Laden’s death and not one year prior before. The current findings demonstrate that liberals and conservatives may react differently after major societal events in predictable ways considering their moral foundations. PMID:28239251

4. VIEW OF RUINS OF FINE ORE MILL (FEATURE 20), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. VIEW OF RUINS OF FINE ORE MILL (FEATURE 20), FACING SOUTHEAST. - Copper Canyon Camp of the International Smelting & Refining Company, Ruins of the Fine Ore Mill, Copper Canyon, Battle Mountain, Lander County, NV

43 CFR 9239.5-1 - Ores.

Code of Federal Regulations, 2012 CFR

2012-10-01

... OF THE INTERIOR TECHNICAL SERVICES (9000) TRESPASS Kinds of Trespass § 9239.5-1 Ores. (a) For ores trespass in a State where there is no State law governing such trespass, the measure of damages will be as...

43 CFR 9239.5-1 - Ores.

Code of Federal Regulations, 2014 CFR

2014-10-01

... OF THE INTERIOR TECHNICAL SERVICES (9000) TRESPASS Kinds of Trespass § 9239.5-1 Ores. (a) For ores trespass in a State where there is no State law governing such trespass, the measure of damages will be as...

43 CFR 9239.5-1 - Ores.

Code of Federal Regulations, 2011 CFR

2011-10-01

... OF THE INTERIOR TECHNICAL SERVICES (9000) TRESPASS Kinds of Trespass § 9239.5-1 Ores. (a) For ores trespass in a State where there is no State law governing such trespass, the measure of damages will be as...

43 CFR 9239.5-1 - Ores.

Code of Federal Regulations, 2013 CFR

2013-10-01

... OF THE INTERIOR TECHNICAL SERVICES (9000) TRESPASS Kinds of Trespass § 9239.5-1 Ores. (a) For ores trespass in a State where there is no State law governing such trespass, the measure of damages will be as...

CONTEXT VIEW SHOWING MODERN TRACKS PASSING UNDER HULETTS AND ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CONTEXT VIEW SHOWING MODERN TRACKS PASSING UNDER HULETTS AND ORE YARD. LOOKING NORTHEAST. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

7. VIEW OF CARRIE No. 3 AND No. 4 ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. VIEW OF CARRIE No. 3 AND No. 4 ORE BRIDGE, ORE YARD AND FURNACES FROM THE HOT METAL BRIDGE. - U.S. Steel Homestead Works, Blast Furnace Plant, Along Monongahela River, Homestead, Allegheny County, PA

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2010 CFR

2010-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2012 CFR

2012-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2011 CFR

2011-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2013 CFR

2013-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2014 CFR

2014-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

Thermodynamic Analysis of the Selective Reduction of a Nickeliferous Limonitic Laterite Ore by Hydrogen

NASA Astrophysics Data System (ADS)

Elliott, R.; Pickles, C. A.

2017-09-01

Nickeliferous limonitic laterite ores are becoming increasingly attractive as a source of metallic nickel as the costs associated with recovering nickel from the sulphide ores increase. Unlike the sulphide ores, however, the laterite ores are not amenable to concentration by conventional mineral processing techniques such as froth flotation. One potential concentrating method would be the pyrometallurgical solid state reduction of the nickeliferous limonitic ores at relatively low temperatures, followed by beneficiation via magnetic separation. A number of reductants can be utilized in the reduction step, and in this research, a thermodynamic model has been developed to investigate the reduction of a nickeliferous limonitic laterite by hydrogen. The nickel recovery to the ferronickel phase was predicted to be greater than 95 % at temperatures of 673-873 K. Reductant additions above the stoichiometric requirement resulted in high recoveries over a wider temperature range, but the nickel grade of the ferronickel decreased.

Benthic and Plankton Foraminifers in Hydrothermally Active Zones of the Mid-Atlantic Ridge (MAR)

NASA Astrophysics Data System (ADS)

Khusid, T. A.; Os'kina, N. S.; Lukashina, N. P.; Gablina, I. F.; Libina, N. V.; Matul, A. G.

2018-01-01

Comparison of benthic foraminiferal assemblages from the core obtained within the Peterburgskoe ore field (Mid-Atlantic Ridge) and from the core taken five kilometers away from the ore field revealed evident differences in their composition, in the appearance of their shells, and also in the benthic-plankton species ratio. It was noted that the foraminiferal assemblage from the ore-bearing sediments of the Petersburg field was characterized by a higher relative content of benthic species and a large number of chemically altered and broken shells. The first occurrence of the species Osangularia umbonifera, which is able to exist in lowoxygen and CaCO3-undersaturated bottom waters at the boundary of biogenic sediments surrounding the ore field and in the ore-bearing sediments, was established. In the core section sampled beyond the ore field, the composition of foraminiferal assemblages differs insignificantly from typical oceanic ones.

Nonlinear metallogeny and the depths of the earth

NASA Astrophysics Data System (ADS)

Shcheglov, A. D.; Govorov, I. N.

This book is concerned with the basic relations regarding a new approach in the field of knowledge of metallogenesis, taking into account the complex character of the mutual dependence between ore deposits, the structure of the earth's crust, and depth relations. The principles of nonlinear metallogeny are examined, giving attention to the development of the metallogenic science during the past few years, the formation of the concept 'nonlinear metallogeny', the main aspects of nonlinear metallogeny, the origin of the ore deposits and the characteristics of ore formations in the mantle, the parallel manifestation of ore-forming processes in the crust, sedimentary-hydrothermal ore formations and their place in nonlinear metallogeny, and various types of rock and ore formations. The structure, composition, and metalliferous characteristics found at various depth zones of the tectonosphere are discussed along with the geochemical and metallogenic heterogeneity in the mantle. General questions of nonlinear metallogeny are also investigated.

Metal cation exchange reactions of ore minerals in Fe-Mn crusts of the Marcus Wake Rise (Pacific Ocean) in aqueous-salt solutions

NASA Astrophysics Data System (ADS)

Novikov, G. V.; Bogdanova, O. Yu.; Melnikov, M. E.; Drozdova, A. N.; Lobus, N. V.; Shulga, N. A.

2017-12-01

It is shown that the reaction ability of metal cations of ore minerals in Fe-Mn crusts of the Marcus Wake Rise increases in the following manner: (Co2+ < Cu2+ < Ni2+) < (Mg2+ < Mn2+ < K+ ≈ Ca2+ ≈ Na+). The composition of the exchange complex of the ore minerals is constant and includes these metal cations. Ca2+ and Na+ are major contributors to the exchange capacity of the ore minerals. The capacity of the ore minerals by cations of alkali and base metals is 0.43-0.60 and 2.08-2.70 mg-equiv/g, respectively. The exchange capacity of the ore minerals by cations of base metals increases linearly with the increase in the MnO2 content of the crust and does not depend on the geographical locations of the Marcus Wake guyots.