Seismic stratigraphy of the Mississippi-Alabama shelf and upper continental slope

USGS Publications Warehouse

Kindinger, J.L.

1988-01-01

The Mississippi-Alabama shelf and upper continental slope contain relatively thin Upper Pleistocene and Holocene deposits. Five stages of shelf evolution can be identified from the early Wisconsinan to present. The stages were controlled by glacioeustatic or relative sea-level changes and are defined by the stratigraphic position of depositional and erosional episodes. The stratigraphy was identified on seismic profiles by means of geomorphic pattern, high-angle clinoform progradational deposits, buried stream entrenchments, planar conformities, and erosional unconformities. The oldest stage (stage 1) of evolution occurred during the early Wisconsinan lowstand; the subaerially exposed shelf was eroded to a smooth seaward-sloping surface. This paleosurface is overlain by a thin (< 10 m) drape of transgressive deposits (stage 2). Stage 3 occurred in three phases as the late Wisconsinan sea retreated: (1) fluvial channel systems eroded across the shelf, (2) deposited a thick (90 m) shelf-margin delta, and (3) contemporaneously deposited sediments on the upper slope. Stage 4 included the rapid Holocene sea-level rise that deposited a relatively thin transgressive facies over parts of the shelf. The last major depositional episode (stage 5) was the progradation of the St. Bernard delta over the northwestern and central parts of the area. A depositional hiatus has occurred since the St. Bernard progradation. These Upper Quaternary shelf and slope deposits provide models for analogous deposits in the geologic record. Primarily, they are examples of cyclic sedimentation caused by changes in sea level and may be useful in describing short-term, sandy depositional episodes in prograding shelf and slope sequences. ?? 1988.

The Saguenay Fjord, Quebec, Canada: Integrating marine geotechnical and geophysical data for spatial seismic slope stability and hazard assessment

USGS Publications Warehouse

Urgeles, R.; Locat, J.; Lee, H.J.; Martin, F.

2002-01-01

In 1996 a major flood occurred in the Saguenay region, Quebec, Canada, delivering several km3 of sediment to the Saguenay Fjord. Such sediments covered large areas of the, until then, largely contaminated fjord bottom, thus providing a natural capping layer. Recent swath bathymetry data have also shown that sediment landslides are widely present in the upper section of the Saguenay Fjord, and therefore, should a new event occur, it would probably expose the old contaminated sediments. Landslides in the Upper Saguenay Fjord are most probably due to earthquakes given its proximity to the Charlevoix seismic region and to that of the 1988 Saguenay earthquake. In consequence, this study tries to characterize the permanent ground deformations induced by different earthquake scenarios from which shallow sediment landslides could be triggered. The study follows a Newmark analysis in which, firstly, the seismic slope performance is assessed, secondly, the seismic hazard analyzed, and finally an evaluation of the seismic landslide hazard is made. The study is based on slope gradients obtained from EM1000 multibeam bathymetry data as well as water content and undrained shear strength measurements made in box and gravity cores. Ground motions integrating local site conditions were simulated using synthetic time histories. The study assumes the region of the 1988 Saguenay earthquake as the most likely source area for earthquakes capable of inducing large ground motions in the Upper Saguenay region. Accordingly, we have analyzed several shaking intensities to deduce that generalized sediment displacements will begin to occur when moment magnitudes exceed 6. Major displacements, failure, and subsequent landslides could occur only from earthquake moment magnitudes exceeding 6.75. ?? 2002 Elsevier Science B.V. All rights reserved.

Influence of filling-drawdown cycles of the Three Gorges reservoir on deformation and failure behaviors of anaclinal rock slopes in the Wu Gorge

NASA Astrophysics Data System (ADS)

Huang, Da; Gu, Dong Ming

2017-10-01

The upper Wu Gorge on the Yangtze River has been the site of tens of reservoir-induced landslides since the filling of the Three Gorges reservoir in 2003. These landslides have been occurring in heavily fractured carbonate rock materials along the rim of the reservoir in the Wu Gorge. A detailed investigation was carried out to examine the influence of reservoir operations (filling and drawdown) on slope stabilities in the upper Wu Gorge. Field investigations reveal many collapses of various types occurred at the toe of the anaclinal rock slopes, owing to the long-term intensive river erosion caused by periodic fluctuation of the reservoir level. Analysis of data from deformation monitoring suggests that the temporal movement of the slopes shows seasonal fluctuations that correlate with reservoir levels and drawdown conditions, with induced slope acceleration peaking when reservoir levels are lowest. This may illustrate that the main mechanism is the reservoir drawdown, which induces an episodic seepage force in the highly permeable materials at the slope toes, and thus leads to the episodic rockslides. The coupled hydraulic-mechanical (HM) modeling of the G2 landslide, which occurred in 2008, shows that collapse initiated at the submerged slope toe, which then caused the upper slope to collapse in a rock topple-rock slide pattern. The results imply that preventing water erosion at the slope toe might be an effective way for landslide prevention in the study area.

Depositional architecture and evolution of the Late Miocene slope channel-fan-system in the northeastern shelf-margin of South China Sea

NASA Astrophysics Data System (ADS)

Jiang, Jing; Lin, Changsong; Zhang, Zhongtao; Tian, Hongxun; Tao, Ze; Liu, Hanyao

2016-04-01

The Upper Miocene in the Pearl River Mouth Basin of northwestern shelf-margin of South China Sea Basin contains a series of slope channel - fan systems. Their depositional architecture and evolution are documented in this investigation based on an integrated analysis of cores, logs, and seismic data. Four depositional-palaeogeomorphological elements have been identified in the slope channel-fan systems as follows: broad, shallow and unconfined or partly confined outer-shelf to shelf-break channels; deeply incised and confined unidirectionally migrating slope channels; broad or U-shaped, unconfined erosional-depositional channels; frontal splays-lobes and nonchannelized sheets. The slope channels are mostly oriented NW-SE, which migrated unidirectionally northeastwards and intensively eroded almost the whole shelf-slope zone. The channel infillings are mainly mudstones, interbedded with siltstones. They might be formed by gravity flow erosion as bypassing channels. They were filled with limited gravity flow sediments at the base and mostly filled with lateral accretionary packages of bottom current deposits. At the end of the channels, a series of small-scale slope fans developed and coalesced into fan aprons along the base of the slope. The unconfined erosional-depositional channels at the upper parts of the fan-apron-systems display compound infill patterns, and commonly have concave erosional bases and convex tops. The frontal splays-lobes representing middle to distal deposits of fan-apron-systems have flat-mounded or gull-wing geometries, and the internal architectures include bidirectional downlap, progradation, and chaotic infillings. The distal nonchannelized turbidite sheets are characterized by thin-bedded, parallel to sub-parallel sheet-like geometries. Three major unconformities or obvious erosional surfaces in the channel-fan systems of the Upper Miocene are recognized, and indicate the falling of sea-level. The depositional architecture of sequences varies from the upper slope to the slope base transitional to basin plain. The basal erosion and the unidirectionally migrating characters of the slope channels were supposed to be the result of the interaction of bottom currents and gravity flows. The intensive development of the channel-fan systems over the shelf slope might be related to the Dongsha Tectonic uplift which may resulted in stepped slope and concomitantly intensified gravity flow in the study area in Late Miocene.

Tectonic Structure of the Middle America Pacific Margin and Incoming Cocos Plate From Costa Rica to Guatemala

NASA Astrophysics Data System (ADS)

Ranero, C. R.; Weinrebe, W.; Grevemeyer, I.; Phipps Morgan, J.; Vannucchi, P.; von Huene, R.

2003-12-01

A new multibeam bathymetry and magnetic survey with R/V SONNE in summer 2003 has mapped the continental margin and incoming plate of NW Nicaragua, El Salvador and Guatemala, extending existing coverage from offshore Costa Rica and part of Nicaragua to a full coverage map of about 1200 km long by 100 km wide area along the plate boundary. The incoming plate along Nicaragua, El Salvador and Guatemala is of similar age and was formed at superfast spreading rates; however, its morphology changes drastically along strike. The seafloor-spreading inherited morphology is very smooth along Nicaragua, but with ridges up to 800 m high in Guatemala, with a transition across El Salvador. The development and dimensions of the dominant inherited fabric seems to be related to discontinuities at the paleospreading center. A series of troughs oblique to the main fabric may indicate the location of pseudofaults and correspond to areas where the seafloor fabric is most prominent. Bending of the oceanic plate into the trench reactivates the inherited fabric forming a well pervasive faulting system along the oceanic trench slope. The continental slope displays three morphotectonic units that roughly correspond to the upper, middle and lower slope, although the across slope width of each unit is fairly variable. Small canyons and gullies that form at the sudden dip change across the shelf break carve the upper slope. The canyons coalesce and become shallower as the dip decreases downslope. Locally some large canyons continue into the slope toe. The middle slope is a rough terrain variable in width and dip sculptured by pervasive normal faulting and locally by mass wasting processes. The lower slope is formed by en echelon terraces striking similar to the rough terrain of the incoming plate and mimicking the half graben morphology of the underthusting plate. The three morphotectonic slope domains represent differences in tectonic activity, with more stable upper slope, a middle slope dominated by tectonic extension and the thin, highly fractured upper plate of the lower slope riffling over the incoming plate topography. The trench axis is largely empty, with local turbidite ponds at the mouth of a few large canyons transecting the entire slope.

Slope gradient and shape effects on soil profiles in the northern mountainous forests of Iran

NASA Astrophysics Data System (ADS)

Fazlollahi Mohammadi, M.; Jalali, S. G. H.; Kooch, Y.; Said-Pullicino, D.

2016-12-01

In order to evaluate the variability of the soil profiles at two shapes (concave and convex) and five positions (summit, shoulder, back slope, footslope and toeslope) of a slope, a study of a virgin area was made in a Beech stand of mountain forests, northern Iran. Across the slope positions, the soil profiles demonstrated significant changes due to topography for two shape slopes. The solum depth of the convex slope was higher than the concave one in all five positions, and it decreased from the summit to shoulder and increased from the mid to lower slope positions for both convex and concave slopes. The thin solum at the upper positions and concave slope demonstrated that pedogenetic development is least at upper slope positions and concave slope where leaching and biomass productivity are less than at lower slopes and concave slope. A large decrease in the thickness of O and A horizons from the summit to back slope was noted for both concave and convex slopes, but it increased from back slope toward down slope for both of them. The average thickness of B horizons increased from summit to down slopes in the case of the concave slope, but in the case of convex slope it decreased from summit to shoulder and afterwards it increased to the down slope. The thicknesses of the different horizons varied in part in the different positions and shape slopes because they had different plant species cover and soil features, which were related to topography.

Antecedent topography and morphological controls on sediment accumulation and slope stability of the U.S. Atlantic margin

NASA Astrophysics Data System (ADS)

Hill, J. C.; Brothers, D. S.; Ten Brink, U. S.; Andrews, B. D.

2017-12-01

The U.S. Atlantic margin encompasses a wide variety of slope failure processes, ranging from small canyon-confined failures on the upper slope to large, open slope landslides originating in deeper water. Here we used a suite of high-resolution multibeam bathymetry and detailed multichannel seismic data coverage to investigate the relationship between modern seafloor morphology, pre-existing stratigraphy and sediment accumulation patterns. We suggest that a combination of sediment supply and antecedent margin physiography, whereby variations in margin evolution during the Miocene have influenced the modern seafloor morphology, controls both the location of slope sediment accumulation and the style of slope failure. Oversteepened margins with angular shelf breaks and steep upper slopes, referred to as oblique margins, are characterized by downslope mass transport and densely-spaced canyon formation. These margins are most likely the locus of canyon-confined failures and smaller lower slope fan-apron failures (e.g., much of the Mid-Atlantic). Sigmoidal margins with prograded slopes, a rounded shelf edge, and a low gradient slope morphology can support significant sediment accumulation across a broad area, with limited canyon development. These margins are often associated with high sediment supply and are prone to large, upper slope slab-style failures (e.g., the Hudson Apron, southwestern New England, the Currituck and Cape Fear Slide complexes). Areas with morphologies in between these two end members are characterized by limited shelf-edge accommodation space and large-scale lower slope accumulation and onlap, representing transitional stages of equilibrium slope adjustment. Large failures along these intermediate-type margins tend to develop lower on the slope where thick wedges of onlapping sediment are found (e.g., around Washington Canyon, Cape Lookout and southeastern New England). As antecedent topography and sediment loading appear to play an important role in determining the spatial distribution of submarine slope failures, other key processes that contribute to the development of overpressure (e.g., sediment compaction and fluid migration) should be examined with this in mind to improve our understanding of the geologic factors that precondition slopes for failure.

The modern Kaoping transient fan offshore SW Taiwan: Morphotectonics and development

NASA Astrophysics Data System (ADS)

Hsiung, Kan-Hsi; Yu, Ho-Shing; Chiang, Cheng-Shing

2018-01-01

Using bathymetry and seismic reflection profiles, this study examined and determined the transient nature of the Kaoping Fan located in the topographically complex slope offshore southwest Taiwan. Kaoping Fan is located west of the lower reach of the Kaoping Canyon at the lower Kaoping Slope, ranging from 2,200 to 3,000 m water depth, and has a relatively small areal extent restricted in the topographic lows confined by structural highs due to mud diapiric uplifting and thrust faulting. Kaoping Fan shows an asymmetrical triangular fan-shaped bathymetric feature elongated in an NW-SE direction but with a strong skew toward the east. The fan deposits consist of three main seismic facies: layered high-amplitude reflections in the upper section and stratified, parallel to sub-parallel low-amplitude reflections with variable continuity and channel fill facies in the lower section. In the absence of ground-truthing from core data, the seismic patterns suggest that the Kaoping Fan recorded the onset of channelized and over-bank deposits in the lower part and layered turbidite facies in the upper part subsequently. The development of the Kaoping Fan can be divided into three stages in terms of canyon activities and fan-feeding processes. Initially, Kaoping Fan was mainly fed by a point sediment source at the apex of the fan. Secondly, Kaoping Fan was maintained as a slope fan, mainly fed laterally by over-spilled sediments from the canyon. Finally, the Kaoping Canyon completely passes through the Kaoping Fan and supplies over-spilled sediments laterally, forming a transient fan with canyon incision and sediment by-passing. The accumulation of sediments and the growth of Kaoping Fan are primarily controlled by inherited complex paleo-topography and the evolution of Kaoping Canyon. The sediment delivery system of Kaoping Fan is characterized by lateral supply of over-spilling sediment flows and sediments bypassing to and beyond the base of slope. The Kaoping Fan together with the ponded Fangliao Fan in the topographically complex Kaoping Slope can be used as a type model for evaluating the topographic effects on the development of submarine fans on complex slopes in general.

The influence of paleo currents upon the Santaren Channel and the adjacent carbonate platforms, Bahamas.

NASA Astrophysics Data System (ADS)

Paulat, Marco; Lüdmann, Thomas; Betzler, Christian; Eberli, Gregor; Lindhorst, Sebastian

2015-04-01

The closure of the Central American Seaway and the reorganization of the ocean currents had a global impact on earth's climate. The sedimentation of the Great Bahama Bank (GBB) and the smaller Cay Sal Bank (CSB) are influenced by the Atlantic North Equatorial Current and the Florida Current. New high-resolution multichannel seismic data sets tied to the IODP leg 166 wells document that the shape of Bahama Banks and the sedimentation processes in the Santaren Channel (SC) between GBB and CSB are strongly related to changes in the strength of these currents. Since the Upper Miocene, the SC is filled up by a huge package of drift sediments, namely the Santaren Drift (SD). The buildup of the SD causes a local high in the recent bathymetry perpendicular to the surrounding steep platform slopes. The SD shows a typical mounded morphology and progrades northwards in direction of the Florida Channel. The SD was established during the late Miocene. Seismic facies and internal configuration indicate an environment of a stable north flowing current with a major depocenter related to the center of the SC. Additionally, a second depocenter at the central eastern flank of CSB established and preserved till early Pleistocene when the slope sedimentation starts to dominate. This depocenter points to a strengthened countercurrent component in the eastern SC. From the lower Pliocene to the upper Pleistocene the volume of the SD expanded, associated with an intensification of the current in the SC along its eastern flank, indicated by deep erosional channels parallel to the margin of GBB in the northern part of the survey area. This trend probably was initiated as a consequence of current reorganization due to the final closure of the Central American Seaway. Lower slope sediments from GBB are eroded or only minor parts are preserved from lower Pliocene to upper Pleistocene. With late Pliocene falling sea-level, gravitational slope sedimentation from GBB into the SC increased with concurrent decrease in sedimentation rate of the SD. The drift depocenter shifted toward the margin of the GBB, approaching the modern situation.

Potential geologic hazards on the eastern Gulf of Cadiz slope (SW Spain)

USGS Publications Warehouse

Baraza, J.; Ercilla, G.; Nelson, C.H.

1999-01-01

Geologic hazards resulting from sedimentary, oceanographic and tectonic processes affect more than one third of the offshore Gulf of Cadiz, and are identified by interpreting high-resolution seismic profiles and sonographs. Hazards of sedimentary origin include the occurrence of slope instability processes in the form of single or multiple slumps occupying up to 147 km2 mainly concentrated in the steeper, upper slope area. Besides the presence of steep slopes, the triggering of submarine landslides is probably due to seismic activity and favoured by the presence of biogenic gas within the sediment. Gassy sediments and associated seafloor pockmarks cover more than 240 km2 in the upper slope. Hazards from oceanographic processes result from the complex system of bottom currents created by the interaction of the strong Mediterranean Undercurrent and the rough seafloor physiography. The local intensification of bottom currents is responsible for erosive processes along more than 1900 km2 in the upper slope and in the canyons eroded in the central area of the slope, undermining slopes and causing instability. The strong bottom currents also create a mobile seafloor containing bedforms in an area of the Gulf that extends more than 2500 km2, mostly in the continental slope terraces. Hazards of tectonic origin are important because the Gulf of Cadiz straddles two major tectonic regions, the Azores-Gibraltar fracture zone and the Betic range, which results in diapir uplift over an area of more than 1000 km2, and in active seismicity with earthquakes of moderate magnitude. Also, tsunamis produced by strong earthquakes occur in the Gulf of Cadiz, and are related to the tectonic activity along the Azores-Gibraltar fracture zone.

Landslide landscape in monocline slate topography of in south Taiwan

NASA Astrophysics Data System (ADS)

Chen, T.; Zhang, M.; Zhou, L.; Chen, M.; Zhong, P.

2012-12-01

Geomorphologic curvature is one of factor affecting the landslides occurrence, curvature represent a situation of location erosion. This study based on landslide inventory, DEM, and geological survey database, the study explores the relationship between curvature and landslide areas, location, and slope type. The study area is Ai-Liao Xi basin, south Taiwan, which flows through four towns in Pingtung County. The main strata of the catchment is Miocene sub-metamorphic rocks, with the majority of which consists of argillite, slate and phyllite as well as dark gray quartz sandstones. The study area is about 34,000ha, 80% of which are hill area. 1200 landslides caused by 2009 Typhoon Morakot have been recognized and studied. Results revealed that, a certain degree of deflection usually occurs before a large landslide initiation on the dip slope. The greater the curvature, the a large-scaled landslide occur frequently. Most of the profile curvatures of the landslide sites are either very convex or concave in their shape. This suggests that the deformation (and the subsequent damage) of the dip slope is progressive. Whether profile curvature is positive or negative would have collapsed, and it is not significantly distinguish to the landslide areas size. Finally, the main types of landslide is the flat slope on the dip slope, and the positive curvature are related with the creep of rock mass, the negative curvature are much related to the upper stream erosion.

Late Holocene Radiocarbon Variability in Northwest Atlantic Slope Waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sherwood, O; Edinger, E; Guilderson, T P

2008-08-15

Deep-sea gorgonian corals secrete a 2-part skeleton of calcite, derived from dissolved inorganic carbon at depth, and gorgonin, derived from recently fixed and exported particulate organic matter. Radiocarbon contents of the calcite and gorgonin provide direct measures of seawater radiocarbon at depth and in the overlying surface waters, respectively. Using specimens collected from Northwest Atlantic slope waters, we generated radiocarbon records for surface and upper intermediate water layers spanning the pre- and post bomb-{sup 14}C eras. In Labrador Slope Water (LSW), convective mixing homogenizes the pre-bomb {Delta}{sup 14}C signature (-67 {+-} 4{per_thousand}) to at least 1000 m depth. Surface watermore » bomb-{sup 14}C signals were lagged and damped (peaking at {approx} +45{per_thousand} in the early 1980s) relative to other regions of the northwest Atlantic, and intermediate water signals were damped further. Off southwest Nova Scotia, the vertical gradient in {Delta}{sup 14}C is much stronger. In surface water, pre-bomb {Delta}{sup 14}C averaged -75 {+-} 5{per_thousand}. At 250-475 m depth, prebomb {Delta}{sup 14}C oscillated quasi-decadally between -80 and -100{per_thousand}, likely reflecting interannual variability in the presence of Labrador Slope Water vs. Warm Slope Water (WSW). Finally, subfossil corals reveal no systematic changes in vertical {Delta}{sup 14}C gradients over the last 1200 years.« less

Export of a Winter Shelf Phytoplankton Bloom at the Shelf Margin of Long Bay (South Atlantic Bight, USA)

NASA Astrophysics Data System (ADS)

Nelson, J.; Seim, H.; Edwards, C. R.; Lockhart, S.; Moore, T.; Robertson, C. Y.; Amft, J.

2016-02-01

A winter 2012 field study off Long Bay (seaward of Myrtle Beach, South Carolina) investigated exchange processes along the shelf margin. Topics addressed included mechanisms of nutrient input (upper slope to outer shelf), phytoplankton blooms and community characteristics (mid-to-outer shelf), and possible export of shelf bloom material (transport to and across the shelf break to the upper slope). Observations utilized three moorings (mid-shelf, shelf break, upper slope), two gliders and ship operations (repeat cruises with profiling, water sampling and towed body surveys) along with satellite SST and ocean color imagery and near-by NOAA buoy records. Here we focus on the late January to early February period, when a mid-shelf bloom of Phaeocystis globosa (which forms large gelatinous colonies) was transported to the shelf break. The presence of Phaeocystis colonies resulted in strong spiking in chlorophyll (chl) fluorescence profiles. A partitioning approach was adapted to estimate chl in colonies (spikes) and small forms (baseline signal) and to account for an apparent difference in measured in vivo fluorescence per unit chl (lower in colonies). Up to 40-50% of chl in the bloom (surface to bottom on the mid-shelf) was estimated to be in the colonies. In late January, there a pronounced seaward slumping of relatively dense mid-shelf water along the bottom under warmer surface water derived from the inshore edge of a broad jet of Gulf Stream water flowing southwestward along the upper slope. We describe the evolution of this event and the conditions which set up this mechanism for episodic near-bed transport of fresh bloom material produced on the shelf to the upper slope off Long Bay. Down-slope transport may have been enhanced in this case by the high phytoplankton biomass in gelatinous colonies, which appeared to be settling in the water column on the shelf prior to the transport event.

Shelf architectures of an isolated Late Cretaceous carbonate platform margin, Galala Mountains (Eastern Desert, Egypt)

NASA Astrophysics Data System (ADS)

Scheibner, C.; Marzouk, A. M.; Kuss, J.

2001-12-01

An asymmetrical carbonate platform margin to basin transect has been investigated in the Upper Campanian-Maastrichtian succession of the Galala Mountains, northern Egypt. Identification of systems tracts and their lateral correlation was possible in slope sections only, whereas the monotonous chalk-marl alternations of the basinal sections could not be subdivided with respect to sequence stratigraphic terminology. The platform asymmetry is expressed by varying large-scale depositional architectures exhibiting a rimmed platform with a sigmoidal slope curvature in south-easterly dip-sections and a ramp with a linear slope curvature in south-westerly dip-sections. The rimmed platform is subdivided into a gentle upper slope and a steep lower slope. The platform formed as a result of the initial topography that was controlled by the tectonic uplift of the Northern Galala/Wadi Araba Syrian Arc structure. The calculated angles of the steep lower slope of the rimmed part range from 5 to 8°, whereas the ramp part has an angle of less than 0.1°.

Effects of lava heating on volatile-rich slopes on Io

USGS Publications Warehouse

Dundas, Colin M.

2017-01-01

The upper crust of Io may be very rich in volatile sulfur and SO2. The surface is also highly volcanically active, and slopes may be warmed by radiant heat from the lava. This is particularly the case in paterae, which commonly host volcanic eruptions and long-lived lava lakes. Paterae slopes are highly variable, but some are greater than 70°. I model the heating of a volatile slope for two end-member cases: instantaneous emplacement of a large sheet flow, and persistent heating by a long-lived lava lake. In general, single flows can briefly raise sulfur to the melting temperature, or drive a modest amount of sublimation of SO2. Persistently lava-covered surfaces will drive much more significant geomorphic effects, with potentially significant sublimation and slope retreat. In addition to the direct effects, heating is likely to weaken slope materials and may trigger mass wasting. Thus, if the upper crust of Io is rich in these volatile species, future missions with high-resolution imaging are likely to observe actively retreating slopes around lava lakes and other locations of frequent eruptions.

Analysis of flowpath dynamics in a steep unchannelled hollow in the Tanakami Mountains of Japan

NASA Astrophysics Data System (ADS)

Uchida, Taro; Asano, Yuko; Ohte, Nobuhito; Mizuyama, Takahisa

2003-02-01

Simultaneous measurements of runoff, soil pore water pressure, soil temperature, and water chemistry were taken to evaluate the spatial and temporal nature of flowpaths in a steep 0·1 ha unchannelled hollow in the Tanakami Mountains of central Japan. Tensiometers showed that a saturated area formed and a downward hydraulic gradient existed continuously in the area near a spring. The amplitude of the soil-bedrock interface temperature difference near the spring was smaller than that in the upper hollow, although soil depth near the spring was smaller than in the upper hollow. This suggests that, in the small perennially saturated area near the spring, water percolates through the vadose zone mixed with water emerging from the bedrock. During summer rainstorms, the soil-bedrock interface temperature increased as the ground became saturated. Silica and sodium concentrations in the transient saturated groundwater during these episodes were significantly lower than those in the perennial groundwater, suggesting that both rainwater and shallow soil water had important effects on the formation of transient saturated groundwater on the upper slope. In this case, the streamflow varied with the soil pore water pressure on the upper slope; the soil pore water pressure in the area near the spring remained nearly constant. Moreover, the spring water temperature was almost the same as the transient groundwater temperature on the upper slope. This indicates that the transient groundwater in the upper slope flowed to the spring via lateral preferential paths. The relative inflow of bedrock groundwater to the spring decreased as rainfall increased.

Temporal variations of mobile carbohydrates in Abies fargesii at the upper tree limits.

PubMed

Dang, H S; Zhang, K R; Zhang, Q F; Xu, Y M

2015-01-01

Low temperatures are associated high-altitude treelines, but the functional mechanism of treeline formation remains controversial. The relative contributions of carbon limitation (source activity) and growth limitation (sink activity) require more tests across taxa and regions. We examined temporal variations of mobile carbon supply in different tissues of Abies fargesii across treeline ecotones on north- and south-facing slopes of the Qinling Mountains, China. Non-structural carbohydrate (NSC) concentrations in tissues along the altitudinal gradient on both slopes changed significantly in the early and late growing season, but not in the mid-growing season, indicating the season-dependent carbon supply status. Late in the growing season on both slopes, trees at the upper limits had the highest NSC concentrations and total soluble sugars and lowest starch concentrations compared to trees at the lower elevations. NSC concentrations tended to increase in needles and branches throughout the growing season with increasing elevation on both slopes, but declined in roots and stems. NSC concentrations across sampling dates also indicated increases in needles and branches, and decreases in roots and stem with increasing elevation. Overall altitudinal trends of NSC in A. fargesii revealed no depletion of mobile carbon reserves at upper elevation limits, suggesting limitation of sink activity dominates tree life across treeline ecotones in both north- and south-facing slopes. Carbon reserves in storage tissues (especially roots) in the late growing season might also play an important role in winter survival and early growth in spring at upper elevations on both slopes, which define the uppermost limit of A. fargesii. © 2014 German Botanical Society and The Royal Botanical Society of the Netherlands.

The effect of uphill and downhill walking on gait parameters: A self-paced treadmill study.

PubMed

Kimel-Naor, Shani; Gottlieb, Amihai; Plotnik, Meir

2017-07-26

It has been shown that gait parameters vary systematically with the slope of the surface when walking uphill (UH) or downhill (DH) (Andriacchi et al., 1977; Crowe et al., 1996; Kawamura et al., 1991; Kirtley et al., 1985; McIntosh et al., 2006; Sun et al., 1996). However, gait trials performed on inclined surfaces have been subject to certain technical limitations including using fixed speed treadmills (TMs) or, alternatively, sampling only a few gait cycles on inclined ramps. Further, prior work has not analyzed upper body kinematics. This study aims to investigate effects of slope on gait parameters using a self-paced TM (SPTM) which facilitates more natural walking, including measuring upper body kinematics and gait coordination parameters. Gait of 11 young healthy participants was sampled during walking in steady state speed. Measurements were made at slopes of +10°, 0° and -10°. Force plates and a motion capture system were used to reconstruct twenty spatiotemporal gait parameters. For validation, previously described parameters were compared with the literature, and novel parameters measuring upper body kinematics and bilateral gait coordination were also analyzed. Results showed that most lower and upper body gait parameters were affected by walking slope angle. Specifically, UH walking had a higher impact on gait kinematics than DH walking. However, gait coordination parameters were not affected by walking slope, suggesting that gait asymmetry, left-right coordination and gait variability are robust characteristics of walking. The findings of the study are discussed in reference to a potential combined effect of slope and gait speed. Follow-up studies are needed to explore the relative effects of each of these factors. Copyright © 2017. Published by Elsevier Ltd.

Infaunal community responses to a gradient of trawling disturbance and a long-term Fishery Exclusion Zone in the Southern Tyrrhenian Sea

NASA Astrophysics Data System (ADS)

Mangano, M. Cristina; Kaiser, Michel J.; Porporato, Erika M. D.; Lambert, Gwladys I.; Rinelli, Paola; Spanò, Nunziacarla

2014-03-01

Historically the majority of Mediterranean trawl fisheries occur on the continental shelf with a smaller proportion focused on the shelf slope and deep sea areas. Understanding how trawl fisheries affect the wider ecosystem is an important component of the ecosystem-based approach to fisheries management. In this context the current study examined the impact of the otter trawl fishery on the infaunal communities found on the continental shelf and upper slope off the coast of Sicily and Calabria, Italy. A total of thirty six sites were sampled across a gradient of fishing intensity and from within a large bay from which trawling has been excluded for 22 years. Fishing intensities were ascertained post-hoc from vessel monitoring system data. Seabed characteristics of the sites studied were uniform across the continental shelf and slope areas that were studied, such that the only factor that varied was fishing intensity. The density index (DI) and total number of species (S) were significantly higher in the fishery closure area compared with other continental shelf sites. In particular, bioturbating decapod fauna occurred only within the fishery closure area. Fished sites were dominated primarily by burrowing deposit feeding worms, small bivalves and scavenging biota. In contrast, the response to fishing on the upper slope was less clear. This observation was treated with caution as the power to detect fishing effects was lower for the upper slope sites as a result of possible illegal fishing that had compromised two of the four replicate sites within the closed area. While the present study was able to quantify the effect of the demersal trawl fleet on the benthic infauna of the continental shelf, the effects of trawling on the upper shelf slope remain unclear and warrant further study.

Evaluating environmental drivers of spatial variability in free-living nematode assemblages along the Portuguese margin

NASA Astrophysics Data System (ADS)

Lins, Lidia; Leliaert, Frederik; Riehl, Torben; Pinto Ramalho, Sofia; Alfaro Cordova, Eliana; Morgado Esteves, André; Vanreusel, Ann

2017-02-01

Understanding processes responsible for shaping biodiversity patterns on continental margins is an important requirement for comprehending anthropogenic impacts in these environments and further management of biodiversity. Continental margins perform crucial functions linked to key ecological processes which are mainly structured by surface primary productivity and particulate organic matter flux to the seafloor, but also by heterogeneity in seafloor characteristics. However, to what extent these processes control local and regional biodiversity remains unclear. In this study, two isobathic parallel transects located at the shelf break (300-400 m) and upper slope (1000 m) of the western Iberian margin were used to test how food input and sediment heterogeneity affect nematode diversity independently from the spatial factors geographical distance and water depth. We also examined the potential role of connectedness between both depth transects through molecular phylogenetic analyses. Regional generic diversity and turnover were investigated at three levels: within a station, between stations from the same depth transect, and between transects. High variability in food availability and high sediment heterogeneity at the shelf-break transect were directly linked to high diversity within stations and higher variation in community structure across stations compared to the upper slope transect. Contrastingly, environmental factors (food availability and sediment) did not vary significantly between stations located at the upper slope, and this lack of differences were also reflected in a low community turnover between these deeper stations. Finally, differences in nematode communities between both transects were more pronounced than differences within each of the isobathic transects, but these changes were paralleled by the previously mentioned environmental changes. These results suggest that changes in community structure are mainly dictated by environmental factors rather than spatial differences at the western Iberian margin. Furthermore, phylogenetic relationships revealed no evidence for depth-endemic lineages, indicating regular species interchanges across different depths.

Seabed fluid expulsion along the upper slope and outer shelf of the U.S. Atlantic continental margin

USGS Publications Warehouse

Brothers, D.S.; Ruppel, C.; Kluesner, J.W.; ten Brink, Uri S.; Chaytor, J.D.; Hill, J.C.; Andrews, B.D.; Flores, C.

2014-01-01

Identifying the spatial distribution of seabed fluid expulsion features is crucial for understanding the substrate plumbing system of any continental margin. A 1100 km stretch of the U.S. Atlantic margin contains more than 5000 pockmarks at water depths of 120 m (shelf edge) to 700 m (upper slope), mostly updip of the contemporary gas hydrate stability zone (GHSZ). Advanced attribute analyses of high-resolution multichannel seismic reflection data reveal gas-charged sediment and probable fluid chimneys beneath pockmark fields. A series of enhanced reflectors, inferred to represent hydrate-bearing sediments, occur within the GHSZ. Differential sediment loading at the shelf edge and warming-induced gas hydrate dissociation along the upper slope are the proposed mechanisms that led to transient changes in substrate pore fluid overpressure, vertical fluid/gas migration, and pockmark formation.

Foraminiferal, lithic, and isotopic changes across four major unconformities at Deep Sea Drilling Project Site 548, Goban Spur: Chapter 14 in Initial reports of the Deep Sea Drilling Project

USGS Publications Warehouse

Poag, C. Wylie; Reynolds, Leslie A.; Mazzullo, James M.; Keigwin, Loyd D.

1985-01-01

Sediment samples taken at close intervals across four major unconformities (middle Miocene/upper Miocene, lower Oligocene/upper Oligocene, lower Eocene/upper Eocene, lower Paleocene/upper Paleocene) at DSDP-IPOD Site 548, Goban Spur, reveal that coeval biostratigraphic gaps, sediment discontinuities, and seismic unconformities coincide with postulated low stands of sea level. Foraminiferal, lithic, and isotopic analyses demonstrate that environments began to shift prior to periods of marine erosion, and that sedimentation resumed in the form of turbidites derived from nearby upper-slope sources. The unconformities appear to have developed where a water-mass boundary intersected the continental slope, rhythmically crossing the drill site in concert with sea-level rise and fall.

Impact of slope inclination on salt accumulation

NASA Astrophysics Data System (ADS)

Nachshon, Uri

2017-04-01

Field measurements indicated on high variability in salt accumulation along natural and cultivated slopes, even for relatively homogeneous soil conditions. It was hypothesised that slope inclination has an impact on the location of salt accumulation along the slope. A set of laboratory experiments and numerical models were used to explore the impact of slope inclination on salt accumulation. It was shown, experimentally, that for conditions of saline water source at the lower boundary of the slope - salt accumulates in low concentrations and homogeneously along the entire slope, for moderate slopes. However, as inclination increases high salt concentrations were observed at the upper parts of the slope, leaving the lower parts of the slope relatively free of salt. The traditional flow and transport models did not predict the experimental observations as they indicated also for the moderate slopes on salt accumulation in the elevated parts of the slope, away of the saline water source. Consequently - a conceptual model was raised to explain the laboratory observations. It was suggested that the interactions between slope angle, evaporation rates, hydraulic conductivity of the medium and distribution of wetness along the slope affect the saline water flow path through the medium. This lead to preferential flow path close to the soil-atmosphere interface for the steep slopes, which leads to constant wash of the salts from the evaporation front upward towards the slope upper parts, whereas for the moderate slopes, flow path is below the soil-atmosphere interface, therefore salt that accumulates at the evaporation front is not being transported upward. Understanding of salt dynamics along slopes is important for agricultural and natural environments, as well as for civil engineering purposes. Better understanding of the salt transport processes along slopes will improve our ability to minimize and to cope with soil salinization processes. The laboratory experiments and the new conceptual model fit the field observations and may explain the high variability of salt accumulation along slopes as observed in the field.

Direct observations of the Antarctic Slope Current transport at 113°E

NASA Astrophysics Data System (ADS)

Peña-Molino, B.; McCartney, M. S.; Rintoul, S. R.

2016-10-01

The Antarctic Slope Current (ASC), defined here as the region of westward flow along the continental slope off Antarctica, forms the southern limb of the subpolar gyres. It regulates the exchange of water across the shelf break and provides a path for interbasin westward transport. Despite its significance, the ASC remains largely unobserved around most of the Antarctic continent. Here we present direct velocity observations from a 17 month current meter moored array deployed across the continental slope between the 1000 and the 4200 m isobaths, in the southeastern Indian Ocean near 113°E. The observed time-mean flow consists of a surface-intensified jet associated with the Antarctic Slope Front (ASF) and a broader bottom-intensified westward flow that extends out to approximately the 4000 m isobath and is strongest along the upper slope. The time-mean transport of the ASC is -29.2 Sv. Fluctuations in the transport are large, typically exceeding the mean by a factor of 2. They are mainly due to changes in the northward extent of the current over the lower slope. However, seasonal changes in the wind also drive variations in the transport of the ASF and the flow in the upper slope. Both mean and variability are largely barotropic, thus invisible to traditional geostrophic methods.

Examining Predictive Validity of Oral Reading Fluency Slope in Upper Elementary Grades Using Quantile Regression.

PubMed

Cho, Eunsoo; Capin, Philip; Roberts, Greg; Vaughn, Sharon

2017-07-01

Within multitiered instructional delivery models, progress monitoring is a key mechanism for determining whether a child demonstrates an adequate response to instruction. One measure commonly used to monitor the reading progress of students is oral reading fluency (ORF). This study examined the extent to which ORF slope predicts reading comprehension outcomes for fifth-grade struggling readers ( n = 102) participating in an intensive reading intervention. Quantile regression models showed that ORF slope significantly predicted performance on a sentence-level fluency and comprehension assessment, regardless of the students' reading skills, controlling for initial ORF performance. However, ORF slope was differentially predictive of a passage-level comprehension assessment based on students' reading skills when controlling for initial ORF status. Results showed that ORF explained unique variance for struggling readers whose posttest performance was at the upper quantiles at the end of the reading intervention, but slope was not a significant predictor of passage-level comprehension for students whose reading problems were the most difficult to remediate.

Flow and sediment transport dynamics in a slot and cauldron blowout and over a foredune, Mason Bay, Stewart Island (Rakiura), NZ

NASA Astrophysics Data System (ADS)

Hesp, Patrick A.; Hilton, Michael; Konlecher, Teresa

2017-10-01

This study is the first to simultaneously compare flow and sediment transport through a blowout and over an adjacent foredune, and the first study of flow within a highly sinuous, slot and cauldron blowout. Flow across the foredune transect is similar to that observed in other studies and is primarily modulated by across-dune vegetation density differences. Flow within the blowout is highly complex and exhibits pronounced accelerations and jet flow. It is characterised by marked helicoidal coherent vortices in the mid-regions, and topographically vertically forced flow out of the cauldron portion of the blowout. Instantaneous sediment transport within the blowout is significant compared to transport onto and/or over the adjacent foredune stoss slope and ridge, with the blowout providing a conduit for suspended sediment to reach the downwind foredune upper stoss slope and crest. Medium term (4 months) aeolian sedimentation data indicates sand is accumulating in the blowout entrance while erosion is taking place throughout the majority of the slot, and deposition is occurring downwind of the cauldron on the foredune ridge. The adjacent lower stoss slope of the foredune is accreting while the upper stoss slope is slightly erosional. Longer term (16 months) pot trap data shows that the majority of foredune upper stoss slope and crest accretion occurs via suspended sediment delivery from the blowout, whereas the majority of the suspended sediment arriving to the well-vegetated foredune stoss slope is deposited on the mid-stoss slope. The results of this study indicate one mechanism of how marked alongshore foredune morphological variability evolves due to the role of blowouts in topographically accelerating flow, and delivering significant aeolian sediment downwind to relatively discrete sections of the foredune.

Water and energy and hydrological limitations of whole-plant conductance along a subalpine forested hillslope

NASA Astrophysics Data System (ADS)

Beverly, D.; Speckman, H. N.; Klatt, A. L.; Ewers, B. E.

2016-12-01

Whole-plant hydraulic conductance is now used in many processed-based ecohydrological models running at the plot to regional scales. Many models, such as Dynamic Global Vegetation Model (DGVM), predict entire ecosystem evapotranspiration (ET) based on a single unvarying plant conductance parameter that assumes no variation in plant traits. However, whole-plant conductance varies in space, time, and with topography. Understanding this variation increases model predictive power for stand and ecosystem level estimates of ET, ultimately reducing uncertainty in predictions of the water balance. We hypothesize that whole-plant conductance (Kw) is water limited in the up-slope stands due to water flow paths and energy limited in down-slope stands due to shading. To test this hypothesis in two adjacent stands in the Medicine Bow Mountains of southern Wyoming. Both mixed conifer stands were south-facing, with the upper stand being 300 m above the down-slope stand. Whole-plant conductance was quantified measuring sapflow (Js) and leaf water potential (WPL) throughout the growing season. To quantify Js, each stand was instrumented with 30 Granier-type sapflow sensors. Leaf-water potentials were measured in monthly 48-hour campaigns sampling every 3 hours. The upper slope stand exhibited significantly lower Kw (approximately 35% lower in spruce and pine) and decreased throughout the growing season, driven by drying soils resulting in lower predawn WPL. In contrast, the down-slope stand Kw peaked in July before decreasing for rest of the summer. Down-slope predawn WPL maintained a consistent predawn WPL until October reflecting consistent water input from the upper slopes and ground water. Including this topographical variation in whole-plant conductance will increase the predictive power of models simulating evapotranspiration at the watershed scale.

Saltwater-freshwater mixing fluctuation in shallow beach aquifers

NASA Astrophysics Data System (ADS)

Han, Qiang; Chen, Daoyi; Guo, Yakun; Hu, Wulong

2018-07-01

Field measurements and numerical simulations demonstrate the existence of an upper saline plume in tidally dominated beaches. The effect of tides on the saltwater-freshwater mixing occurring at both the upper saline plume and lower salt wedge is well understood. However, it is poorly understood whether the tidal driven force acts equally on the mixing behaviours of above two regions and what factors control the mixing fluctuation features. In this study, variable-density, saturated-unsaturated, transient groundwater flow and solute transport numerical models are proposed and performed for saltwater-freshwater mixing subject to tidal forcing on a sloping beach. A range of tidal amplitude, fresh groundwater flux, hydraulic conductivity, beach slope and dispersivity anisotropy are simulated. Based on the time sequential salinity data, the gross mixing features are quantified by computing the spatial moments in three different aspects, namely, the centre point, length and width, and the volume (or area in a two-dimensional case). Simulated salinity distribution varies significantly at saltwater-freshwater interfaces. Mixing characteristics of the upper saline plume greatly differ from those in the salt wedge for both the transient and quasi-steady state. The mixing of the upper saline plume largely inherits the fluctuation characteristics of the sea tide in both the transverse and longitudinal directions when the quasi-steady state is reached. On the other hand, the mixing in the salt wedge is relatively steady and shows little fluctuation. The normalized mixing width and length, mixing volume and the fluctuation amplitude of the mass centre in the upper saline plume are, in general, one-magnitude-order larger than those in the salt wedge region. In the longitudinal direction, tidal amplitude, fresh groundwater flux, hydraulic conductivity and beach slope are significant control factors of fluctuation amplitude. In the transverse direction, tidal amplitude and beach slope are the main control parameters. Very small dispersivity anisotropy (e.g., αL /αT < 5) could greatly suppress mixing fluctuation in the longitudinal direction. This work underlines the close connection between the sea tides and the upper saline plume in the aspect of mixing, thereby enhancing understanding of the interplay between tidal oscillations and mixing mechanisms in tidally dominated sloping beach systems.

The Character and Formation of Elongated Depressions on the Upper Bulgarian Slope

NASA Astrophysics Data System (ADS)

Xu, Cuiling; Greinert, Jens; Haeckel, Matthias; Bialas, Jörg; Dimitrov, Lyubomir; Zhao, Guangtao

2018-06-01

Seafloor elongated depressions are indicators of gas seepage or slope instability. Here we report a sequence of slopeparallel elongated depressions that link to headwalls of sediment slides on upper slope. The depressions of about 250 m in width and several kilometers in length are areas of focused gas discharge indicated by bubble-release into the water column and methane enriched pore waters. Sparker seismic profiles running perpendicular and parallel to the coast, show gas migration pathways and trapped gas underneath these depressions with bright spots and seismic blanking. The data indicate that upward gas migration is the initial reason for fracturing sedimentary layers. In the top sediment where two young stages of landslides can be detected, the slopeparallel sediment weakening lengthens and deepens the surficial fractures, creating the elongated depressions in the seafloor supported by sediment erosion due to slope-parallel water currents.

Sedimentary dynamics and high-frequency sequence stratigraphy of the southwestern slope of Great Bahama Bank

NASA Astrophysics Data System (ADS)

Wunsch, Marco; Betzler, Christian; Eberli, Gregor P.; Lindhorst, Sebastian; Lüdmann, Thomas; Reijmer, John J. G.

2018-01-01

New geophysical data from the leeward slope of Great Bahama Bank show how contour currents shape the slope and induce re-sedimentation processes. Along slope segments with high current control, drift migration and current winnowing at the toe of slope form a deep moat. Here, the slope progradation is inhibited by large channel incisions and the accumulation of large mass transport complexes, triggered by current winnowing. In areas where the slope is bathed by weaker currents, the accumulation of mass transport complexes and channel incision is rather controlled by the position of the sea level. Large slope failures were triggered during the Mid-Pleistocene transition and Mid-Brunhes event, both periods characterized by changes in the cyclicity or the amplitude of sea-level fluctuations. Within the seismic stratigraphic framework of third order sequences, four sequences of higher order were identified in the succession of the upper Pleistocene. These higher order sequences also show clear differences in function of the slope exposure to contour currents. Two stochastic models emphasize the role of the contour currents and slope morphology in the facies distribution in the upper Pleistocene sequences. In areas of high current influence the interplay of erosional and depositional processes form a complex facies pattern with downslope and along strike facies alterations. In zones with lower current influence, major facies alternations occur predominately in downslope direction, and a layer-cake pattern characterizes the along strike direction. Therefore, this study highlights that contour currents are an underestimated driver for the sediment distribution and architecture of carbonate slopes.

Development and sexual dimorphism of the sonic system in three deep-sea neobythitine fishes and comparisons between upper mid and lower continental slope

NASA Astrophysics Data System (ADS)

Fine, Michael L.; Ali, Heba A.; Nguyen, Thanh Kim; Mok, Hin-Kiu; Parmentier, Eric

2018-01-01

Based on morphology, NB Marshall identified cusk-eels (family Ophidiidae) as one of the chief sound-producing groups on the continental slope. Due to food scarcity, we hypothesized that sonic systems will be reduced at great depths despite their potential importance in sexual reproduction. We examined this hypothesis in the cusk-eel subfamily Neobythitinae by comparing sonic morphology in Atlantic species from the upper-mid (Dicrolene intronigra) and deeper continental slope (Porogadus miles and Bathyonus pectoralis) with three Taiwanese species previously described from the upper slope (Hoplobrotula armatus, Neobythites longipes and N. unimaculatus). In all six species, medial muscles are heavier in males than in females. Dicrolene has four pairs of sonic muscles similar to the shallow Pacific species, suggesting neobythitine sonic anatomy is conservative and sufficient food exists to maintain a well-developed system at depths exceeding 1 km. The sonic system in Porogadus and Bathyonus was reduced to a single pair of ventral medial muscles that connects to a smaller and thinner swimbladder via a long tendon. Small muscle fiber diameters, a likely indicator of rapid contraction, were present in males of five of the species. However, in Bathyonus, the deepest species (pale coloration, reduced eye size, shorter sonic muscles and longer tendons), muscle fibers were larger suggesting an adaptation to facilitate rapid bladder movement for sound production while using slower contractions and less metabolic energy. The six species separate into three groups in length-weight regressions: the three upper slope species have the greatest weights per unit length, Dicrolene is lower, and the two deep species are further reduced consistent with the hypothesis that food limitation affects sonic anatomy at great depths.

Mechanical Stability of Stratified Sediments along the upper continental Slope off Vesterålen, northern Norway - Insights from in situ CPTU Tests

NASA Astrophysics Data System (ADS)

Voelker, D.; Stegmann, S.; Kreiter, S.; L'Heureux, J. S.; Vanneste, M. W. B.; Baeten, N. J.; Knudsen, S.; Rise, L.; Longva, O.; Brendryen, J.; Haflidason, H.; Chand, S.; Mörz, T.; Kopf, A.

2015-12-01

High-resolution single channel-seismic data (3.5 kHz) reveal small-scale submarine landslide structures and superficial deformation features (e.g. tension cracks) along the gently dipping (3°) upper continental slope west of the Vesterålen Archipelago off northern Norway. Previous laboratory-based geotechnical studies attest that the slope is per sestable and that seismic events in an order of magnitude M5.7 may have triggered the slope sediments to fail. Here we present geotechnical in situ data (sedimentary strength, pore pressure), which were obtained with RV Poseidon in summer 2014 using the static CPTU system GOST. The CPTU system provided high-resolution geotechnical profiles of the uppermost sediments to a maximum penetration depth of ~ 20 m at six sites within the landslide features and beside them in undisturbed slope sediments as reference. The CPTU data reveal the occurrence of mechanically weaker zones (MWZ) by the drop of sedimentary strength. These zones are interbedded by coarser, more competent layers. The occurrence of sensitive fine-grained material may be responsible for the loss of strength in the deeper portion (appx. 12 to 18 m below seafloor). An 1D infinite pseudo-static stability analysis attests that the mechanically weaker zones (MWZ) correlate well with portions, where the Factor of Safety (FoS) ≤ 1 (meta-stable to unstable) indicates permanent deformation or failure in case additional dynamic load is induced by an earthquake. Thus, the mechanically weak layers can be considered as one important pre-condition for landslide activity. In conclusion, the integration of in situ CPTU data with geophysical data improves soil characterization and hence foster a better understanding of the pre-conditioning factors for slope instability at the upper continental slope off Vesterålen. Risk assessment for the present-day slope off Vesterålen is particularly crucial, because the opening of the region for offshore oil and gas exploration is controversially debated.

Influence of Input Hardware and Work Surface Angle on Upper Limb Posture in a Hybrid Computer Workstation.

PubMed

Kingston, David C; Riddell, Maureen F; McKinnon, Colin D; Gallagher, Kaitlin M; Callaghan, Jack P

2016-02-01

We evaluated the effect of work surface angle and input hardware on upper-limb posture when using a hybrid computer workstation. Offices use sit-stand and/or tablet workstations to increase worker mobility. These workstations may have negative effects on upper-limb joints by increasing time spent in non-neutral postures, but a hybrid standing workstation may improve working postures. Fourteen participants completed office tasks in four workstation configurations: a horizontal or sloped 15° working surface with computer or tablet hardware. Three-dimensional right upper-limb postures were recorded during three tasks: reading, form filling, and writing e-mails. Amplitude probability distribution functions determined the median and range of upper-limb postures. The sloped-surface tablet workstation decreased wrist ulnar deviation by 5° when compared to the horizontal-surface computer when reading. When using computer input devices (keyboard and mouse), the shoulder, elbow, and wrist were closest to neutral joint postures when working on a horizontal work surface. The elbow was 23° and 15° more extended, whereas the wrist was 6° less ulnar deviated, when reading compared to typing forms or e-mails. We recommend that the horizontal-surface computer configuration be used for typing and the sloped-surface tablet configuration be used for intermittent reading tasks in this hybrid workstation. Offices with mobile employees could use this workstation for alternating their upper-extremity postures; however, other aspects of the device need further investigation. © 2015, Human Factors and Ergonomics Society.

Morphology, distribution, and development of submarine canyons on the United States Atlantic continental slope between Hudson arid Baltimore Canyons

NASA Astrophysics Data System (ADS)

Twichell, David C.; Roberts, David G.

1982-08-01

The distribution and morphology of submarine canyons off the eastern United States between Hudson and Baltimore Canyons have been mapped by long-range sidescan sonar. In this area canyons are numerous, and their spacing correlates with overall slope gradient; they are absent where the gradient is less than 3°, are 2 to 10 km apart where the gradient is 3° to 5°, and are 1.5 to 4 km apart where the gradient exceeds 6°. Canyons range from straight to sinuous; those having sinuous axes indent the edge of the continental shelf and appear to be older than those that head on the upper slope and have straighter axes. A difference in canyon age would suggest that canyons are initiated on the continental slope and only with greater age erode headward to indent the shelf. Shallow gullies on the middle and upper slope parts of the canyon walls suggest that submarine erosion has been a major process in a recent phase of canyon development. *Present address: British Petroleum, Moorgate, London EC2Y 9BU, England

Ecological niche of three teuthophageous odontocetes in the northwestern Mediterranean Sea

NASA Astrophysics Data System (ADS)

Praca, E.; Gannier, A.

2007-10-01

In the northwestern Mediterranean Sea, sperm whales, pilot whales and Risso's dolphins prey on cephalopods exclusively or preferentially. In order to evaluate their competition, we modelled their habitat suitability with the Ecological Niche Factor Analysis (ENFA) and compared their ecological niche using a discriminant analysis. We used a long term (1995-2005) small boat data set, with visual and acoustic (sperm whale) detections. Risso's dolphin had the shallowest and the more spatially restricted principal habitat, mainly located on the upper part of the continental slope (640 m mean depth). With a wider principal habitat, at 1750 m depth in average, the sperm whale used a deeper part of the slope as well as close offshore waters. Finally, the pilot whale has the most oceanic habitat (2500 m mean depth) mainly located in the central Ligurian Sea and Provençal basin. Therefore, potential competition for food between these species may be reduced by the differentiation of their ecological niches.

Ecological niches of three teuthophageous odontocetes in the northwestern Mediterranean Sea

NASA Astrophysics Data System (ADS)

Praca, E.; Gannier, A.

2008-02-01

In the northwestern Mediterranean Sea, sperm whales, pilot whales and Risso's dolphins prey exclusively or preferentially on cephalopods. In order to evaluate their competition, we modelled their habitat suitability with the Ecological Niche Factor Analysis (ENFA) and compared their ecological niches using a discriminant analysis. We used a long term (1995-2005) small boat data set, with visual and acoustic (sperm whale) detections. Risso's dolphin had the shallowest and the more spatially restricted principal habitat, mainly located on the upper part of the continental slope (640 m mean depth). With a wider principal habitat, at 1750 m depth in average, the sperm whale used a deeper part of the slope as well as the closest offshore waters. Finally, the pilot whale has the most oceanic habitat (2500 m mean depth) mainly located in the central Ligurian Sea and Provençal basin. Therefore, potential competition for food between these species may be reduced by the differentiation of their habitats.

Evidence for Recent Liquid Water on Mars: 'Dry' Processes on One Slope; 'Wet' Processes on Another

NASA Technical Reports Server (NTRS)

2000-01-01

[figure removed for brevity, see original site] [figure removed for brevity, see original site]

How can martian gullies--thought to be caused in part by seepage and runoff of liquid water--be distinguished from the more typical, 'dry' slope erosion processes that also occur on Mars? For one thing, most--though not all--of the gully landforms occur on slopes that face away from the martian equator and toward the pole. For another, slopes that face toward the equator exhibit the same types of features as seen on nearly every other non-gullied slope on Mars.

The example shown here comes from northwestern Elysium Planitia in the martian northern hemisphere. The Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) high resolution view (A, left) shows a portion of a 10 kilometer-(6.2 mi)-diameter meteor impact crater at a resolution of about 9 meters (29.5 ft) per pixel. The crater is shown in the context image (B, middle). The north-facing (or, pole-ward) slope in the MOC view is shadowed because sunlight illuminates the scene from the lower left. In this shadowed area, a series of martian gullies--defined by their erosional alcoves, deep channels, and apron deposits--are seen. On the sunlit south-facing (or equator-ward) slope, a scene more typical of most martian impact craters is present--the upper slopes show layered bedrock, the lower slopes show light-toned streaks of dry debris that has slid down the slope forming talus deposits that are distinctly different from the lobe-like form of gully aprons. The picture in (C) has been rotated so that the two slopes--one with gullies (right) and one without (left)--can be compared.

The crater is located at 36.7oN, 252.3oW. The MOC image was acquired in November 1999 and covers an area 3 km (1.9 mi) wide by 14 km (8.7 mi) long; north is toward the upper right (in A) and it is illuminated by sunlight from the lower left. The Viking 1 orbiter context image (B) was obtained in 1978 and is illuminated from the left; north is up. The MOC image has been rotated in the Explanatory Figure (C) such that north is toward the upper left, illumination is from the lower right.

Upper Campanian calciclastic turbidite sequences from the Hacımehmet area (eastern Pontides, NE Turkey): integrated biostratigraphy and microfacies analysis

NASA Astrophysics Data System (ADS)

Sari, Bilal; Kandemir, Raif; Özer, Sacit; Walaszczyk, Ireneusz; Görmüş, Muhittin; Demircan, Huriye; Yilmaz, Cemil

2014-12-01

The upper Campanian (Cretaceous) of the Hacımehmet area (south of the city of Trabzon; Eastern Pontides) is mainly composed of calciclastic turbidites. The basinal unit of the 119 m thick succession includes thin red pelagic limestone interlayers and conglomerates dominated by volcanic clasts. The overlying upper slope and lower slope units of the sequence consist of an alternation of allochthonous calcarenite/calcirudite beds and pelagic marls and mudstones. Calcarenite/calcirudite beds dominate the upper slope unit of the succession and are composed of transported material, including benthic foraminifers, red algae, bryozoan, crinoid and rudist fragments, inoceramid bivalve prisms and neritic and pelagic carbonate lithoclasts. The occurrence of Helicorbitoides boluensis (Sirel) extracted from the calcarenite/calcirudite beds indicates a Campanian age. Identifiable rudists such as Joufia reticulata Boehm, Bournonia cf. anatolica Ozer, Biradiolites cf. bulgaricus Pamouktchiev and ?Biradiolites sp. from the upper slope unit of the succession indicate a late Campanian- Maastrichtian age. The planktonic foraminifers within the red pelagic limestone beds, marls and mudstones throughout the succession consist mainly of Campanian-Maastrichtian forms and suggest mainly basinal depositional conditions. The presence of Radotruncana cf. calcarata (Cushman) accompanied by Globotruncanita elevata (Brotzen) in the basinal unit of the succession indicates an early late Campanian age for the lower part of the succession. Inoceramid bivalves have been collected from the upper part of the succession. The fauna is dominated by `Inoceramus' tenuilineatus Hall and Meek, 1854 and Cataceramus haldemensis (Giers, 1964); other taxa recognised are: `Inoceramus' algeriensis Heinz, 1932, Platyceramus vanuxemi (Meek and Hayden, 1860), `Inoceramus' cf. nebrascensis Owen, 1852, Cataceramus aff. barabini (Morton, 1834), Cataceramus gandjaensis (Aliev, 1956), and `Inoceramus' sp.; the assemblage indicates the `Inoceramus' tenuilineatus Zone; corresponding to the middle-late Campanian boundary interval. The uppermost part of the succession is characterized by the presence of the trace fossils Scolicia strozzii and Scolicia isp., indicating a mixed Skolithos-Cruziana ichnofacies. This ichnofacies suggests a well-oxygenated environment.

Summary of IODP Expedition 344, CRISP-A2, offshore the Osa Peninsula, Costa Rica

NASA Astrophysics Data System (ADS)

Harris, R. N.; Sakaguchi, A.; Petronotis, K. E.

2013-12-01

The Costa Rica Seismogenesis Project (CRISP) is designed to elucidate the processes that control nucleation and seismic rupture of large earthquakes at erosional subduction zones. The CRISP study area is located offshore the Osa Peninsula where the incoming Cocos Ridge has lifted the seismogenic zone to within reach of scientific drilling. The incoming plate is characterized by low sediment supply, a fast convergence rate, abundant plate interface seismicity, and a change in subducting plate relief along strike. In addition to elucidating processes at erosional convergent margins, this project is complementary to other IODP deep fault drilling projects (e.g., NanTroSEIZE and J-FAST). Expedition 344 (23 October - 11 December, 2012) is the second expedition of CRISP Program A (Integrated Ocean Drilling Program Proposal 537A-Full5) that focused on the shallow lithologic, hydrologic, stress, and thermal conditions that lead to unstable slip in the seismogenic zone. With the exception of not reaching the décollement and the underthrust sediment at the toe site (U1412), Expedition 344 exceeded expectations. Material was recovered from the incoming Cocos plate (Sites U1381 and U1414), the toe of the margin (Site U1412), the mid-slope region (Site U1380), and the upper-slope region (Site U1413). Input sites U1381 and U1414 are characterized by anomalously high heat flow and the flow of fluids. These sites contained abundant ash that will be used to assess the impact of Cocos Ridge subduction on the evolution of the Central American volcanic arc. Although toe Site U1412 did not cross the décollement we did penetrate terrigenous sediments interrupted by a Miocene ooze that may reflect accretion of a frontal prism sliver. Mid-slope Site U1380 yielded a major result in that the upper plate material is not a mélange of oceanic material or the offshore extension of the Caribbean large igneous complex, but forearc basin material consisting of lithic sedimentary units. Upper-slope Site U1413 consists of a terrestrially sourced upper slope sequence consistent with high sediment accumulation rates. Preliminary biostratigraphic and paleomagnetic ages from Sites U1380 and U1413, the midslope and upper slope, respectively, yield sediment accumulation rates between ~290 and 590 m/m.y., an order of magnitude greater than estimated offshore the Nicoya Peninsula.

Air quality in bedded mono-slope beef barns

USDA-ARS?s Scientific Manuscript database

Bedded mono-slope barns are becoming more common in the upper Midwest. Because these are new facilities, little research has been published regarding environmental quality, building management and animal performance in these facilities. A team of researchers from South Dakota State University, USDA ...

A lidar, GIS and basic spatial statistic application for the study of ravine and palaeo-ravine evolution in the upper Vipava valley, SW Slovenia

NASA Astrophysics Data System (ADS)

Popit, Tomislav; Rožič, Boštjan; Šmuc, Andrej; Kokalj, Žiga; Verbovšek, Timotej; Košir, Adrijan

2014-01-01

The analysis of high resolution airborne lidar topography represents an essential tool for the geomorphological investigation of surface features. Here we present a detailed lidar-based geomorphological analysis of the ravines cut into the slopes of the upper Vipava valley, NW Slovenia. The NE slopes are defined by an Oligocene thrust-front of Mesozoic carbonates overthrusted on Tertiary flysch and covered by numerous fan-shaped Quaternary gravity flows, deposited in palaeo-ravines cut into the flysch base rock. In contrast, the opposite SW slopes are composed solely of flysch. The large dextral-slip Vipava fault extending in the NW-SE direction is present in the central part of the valley. Our research revealed that although the ravines on both slopes of the Vipava valley are lithologically and tectonically controlled, significant statistical differences in their directions exist. Thus, ravines on opposite slopes are not solely related to the Vipava fault system deformation, but instead reflect a more complex tectonic setting. We believe that the ravines are controlled by second-order faults and fault zones that connect the Vipava fault with adjacent faults. On the SW slopes, these include connecting faults between the Vipava and the southwestern Raša fault, with the ravines on the NE slopes formed in fault zones connecting the Vipava and northeastern Predjama faults.

40 CFR 81.302 - Alaska.

Code of Federal Regulations, 2011 CFR

2011-07-01

... District Northwest Arctic Borough Southeast Fairbanks Election District Upper Yukon Election District Yukon... Election District Northwest Arctic Borough Southeast Fairbanks Election District Upper Yukon Election... Nome Census Area North Slope Borough Northwest Arctic Borough Southeast Fairbanks Census Area Yukon...

Mutagenic activity of heavy metals in soils of wayside slopes

NASA Astrophysics Data System (ADS)

Fedorova, A. I.; Kalaev, V. N.; Prosvirina, Yu. G.; Goryainova, S. A.

2007-08-01

The genotoxic properties of soils polluted with heavy metals were studied on two wayside slopes covered with trees in the city of Voronezh. The nucleolar test in cells of the apical meristem of Zebrina pendula Schnizl. roots was used. The genotoxic effect of the soils was revealed according to the increased number of 2-and 3-nucleolar cells (from 41 to 54% and from 19 to 23% in the upper part of the first and second slopes, respectively; in the control, their number was 18 and 7%). The mean number of nucleoli per cell increased from 1.7 to 1.95 in the experiment and 1.31 in the control. The increased vehicle emissions, especially when cars go up the slopes (mainly in the upper and middle parts), correlated with the elevated heavy metal (Pb, Cu, Cd, and Zn) contents in the soil. The mutagenic substances may be removed to the Voronezh Reservoir, where they may be accumulated in some living organisms.

Carbonate platform, slope, and basinal deposits of Upper Oligocene, Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armin, R.A.; Cutler, W.G.; Mahadi, S.

1987-05-01

Upper Oligocene platform carbonates (Berai Formation) occur extensively on the Barito shelf in southeastern Kalimantan (Borneo) and are flanked northward by coeval slope and basinal deposits (Bongan Formation) which accumulated in the southwestern part of the Kutei basin. Isolated carbonate buildups equivalent to the Berai Formation also occur within the Kutei basin and were probably deposited on basement highs. The distribution of these facies is fairly well constrained by the study of outcrops, wells, and seismic profiles. The Berai Formation consists of diverse limestone types with a wide range of textures and with dominant skeletal components of large foraminifera, redmore » algae, and corals. Deposition of the Berai Formation occurred in moderate- and high-energy shallow-marine conditions. Slope and basin facies occur in extensional basins adjacent to the shelfal carbonates and peripheral to isolated carbonate buildups. Slope deposits consist of hemipelagic claystone, debris-flow conglomerate, calciturbidite, and volcaniclastic intervals. syndepositional downslope transport of slope deposits was an important process, as indicated by intervals containing redeposited debris flows, intraformational truncation surfaces, slide blocks, and associated shear planes. Recurrent movement on basin-margin faults and local volcanism probably perpetuated instability of slope deposits. Basinal deposits consist of calcareous claystone with intercalated thin, distal calciturbidite and volcaniclastic beds.« less

Salt structure and sediment thickness, Texas-Louisiana continental slope, northwestern Gulf of Mexico

USGS Publications Warehouse

Martin, Raymond G.

1973-01-01

The objectives of this study were to determine the general configuration of the salt surface beneath the Texas-Louisiana continental slope and to isopach the Mesozoic-Cenozoic sedimentary section lying upon it. The structure contour map discloses that the entire slope province between the shelf edge and Sigsbee Escarpment is underlain by salt structures which interconnect at relatively shallow subbottom depths. Salt structures on the slope south of Louisiana and eastern Texas can be grouped according to structural relief and size which define morphological belts of decreasing deformational maturity in a downslope direction. Off northern Mexico and southernmost Texas, salt structures are anticlinal and their trends suggest a structural relationship with the folds of the Mexican Ridge province to the south. Structural trends in the two slope areas meet in the corner of the northwestern gulf where salt structure may have been influenced by a seaward extension of the San Marcos Arch, or an abrupt change in subsalt structural topography. Sediment thickness above the top of salt on the slope averages about 1,400 m (4,620 ft) which is a smaller average than expected from previous estimates. In some synclinal basins between salt structures, sediments may be as thick as 4,000-5,000 m (12,000-17,000 ft). On the average, sedimentary deposits in basins on the upper slope are thicker than on the lower slope. From the isopach map of sediments above salt it is estimated that the U.S. continental slope off Texas and Louisiana contains a sedimentary volume of about 170,000 km3 (41,000 mi3). The bulk of this volume is situated in synclinal basins between domes and principally in those beneath the upper and middle slope regions.

[Influence of different slope position and profile in Disporopsis pernyi forest land on soil microbial biomass and enzyme activity in southwest Karst mountain of China ].

PubMed

Qin, Hua-Jun; He, Bing-Hui; Zhao, Xuan-chi; Li, Yuan; Mao, Wen-tao; Zeng, Qing-ping

2014-09-01

Soil microbial biomass and enzyme activity are important parameters to evaluate the quality of the soil environment. The goal of this study was to determine the influence of different slope position and section in Disporopsis pernyi forest land on the soil microbial biomass and enzyme activity in southwest Karst Mountain. In this study, we chose the Dip forest land at Yunfo village Chengdong town Liangping country Chongqing Province as the study object, to analyze the influence of three different slope positions [Up Slope(US), Middle Slope(MS), Below Slope(BS)] and two different sections-upper layer(0-15 cm) and bottom layer(15-30 cm) on the soil microbial biomass carbon (SMBC), soil microbial biomass nitrogen (SMBN), microbial carbon entropy (qMBC), microbial nitrogen entropy (qMBN) , catalase(CAT), alkaline phosphatase (ALK), urease(URE), and invertase(INV). The results showed that the same trend (BS > MS > US) was found for SMBC, SMBN, qMBC, qMBN, CAT and INV of upper soil layer, while a different trend (BS > US > MS) was observed for ALK. In addition, another trend (MS > US > BS) was observed for URE. The same trend (BS > MS >US) was observed for SMBN, qMBN, CAT, ALK, URE and INV in bottom layer, but a different trend (MS > BS > US) was observed for SMBC and qMBC. The SMBC, SMBN, CAT, ALK, URE and INV manifested as upper > bottom with reduction of the section, while qMBC and qMBN showed the opposite trend. Correlation analysis indicated that there were significant (P <0.05) or highly significant (P < 0.01) positive correlations among SMBC in different slope position and section, soil enzyme activity and moisture. According to the two equations of regression analysis, SMBC tended to increase with the increasing CAT and ALK, while decreased with the increasing pH. Then SMBN tended to increase with the increasing URE and INV.

CFD Analysis of different types of single basin solar stills

NASA Astrophysics Data System (ADS)

Maheswari, C. Uma; Meenakshi Reddy, R.

2018-03-01

The current work deals with the numerical and experimental analysis of a solar still of single basin with improved models of stepped, finned, PCM (Phase modification Materials) instrumentation in single slope. The work is additionally extended to double slope solar still of single basin and also the performances were compared with one another. The one slope basin inclinations were compared for 15° and 20°. From the investigations it had been ascertained that single slope with 20° and PCM instrumentation has given the upper productivity compared to different sorts.

Microbiological transformation of carbon and nitrogen compounds in forest soils of Central Evenkia

NASA Astrophysics Data System (ADS)

Sorokin, N. D.; Aleksandrov, D. E.; Grodnitskaya, I. D.; Evgrafova, S. Yu.

2017-04-01

It has been found that the total productivity of bacteria and micromycetes in the 0- to 50-cm layer of homogeneous cryozems (Cryosols) on slopes of northern and southern exposures varies from 1.2 to 1.4 t/ha, respectively, and the calculated content of microbial carbon varies in the range 0.7-0.9 t/ha. The respiratory activity of the upper soil layer is 2.5-2.6 μg C-CO2/(g h); the potential methane formation capacity reaches 0.13 nmol CH4/(m2 day) for soils on slopes of northern exposure and 0.16 nmol CH4/(m2 day) for slopes of southern exposure. Accumulation of sorbed ammonium is recorded in the range 15-17 mg NH4/100 g soil in summer. The increase of temperature in the upper horizons of soils on slopes of southern exposure by 5°C compared to the northern slopes results in only an insignificant increase in the emission of CO2 and CH4. The accumulation of sorbed ammonium and nitrate nitrogen in homogeneous cryozems during the vegetation period is comparable to that in gray forest soils of the southern taiga subzone of the Middle Siberia.

Sedimentary evolution of the Pliocene and Pleistocene Ebro margin, northeastern Spain

USGS Publications Warehouse

Alonso, B.; Field, M.E.; Gardner, J.V.; Maldonado, A.

1990-01-01

The Pliocene and Pleistocene deposits of the Spanish Ebro margin overlie a regional unconformity and contain a major disconformity. These unconformities, named Reflector M and Reflector G, mark the bases of two seismic sequences. Except for close to the upper boundary where a few small channel deposits are recognized, the lower sequence lacks channels. The upper sequence contains nine channel-levee complexes as well as base-of-slope aprons that represent the proximal part of the Valencia turbidite system. Diverse geometries and variations in seismic units distinguish shelf, slope, base-of-slope and basin-floor facies. Four events characterize the late Miocene to Pleistocene evolution of the Ebro margin: (a) formation of a paleodrainage system and an extensive erosion-to-depositional surface during the latest Miocene (Messinian), (b) deposition of hemipelagic units during the early Pliocene, (c) development of canyons during the late Pliocene to early Pleistocene, and (d) deposition of slope wedges, channel-levee complexes, and base-of-slope aprons alternating with hemipelagic deposition during the Pleistocene. Sea-level fluctuations influenced the evolution of the sedimentary sequences of the Ebro margin, but the major control was the sediment supply from the Ebro River. ?? 1990.

Tidally driven water column hydro-geochemistry in a remediating acidic wetland

NASA Astrophysics Data System (ADS)

Johnston, Scott G.; Keene, Annabelle F.; Bush, Richard T.; Sullivan, Leigh A.; Wong, Vanessa N. L.

2011-10-01

SummaryManaged tidal inundation is a newly evolved technique for remediating coastal acid sulphate soil (CASS) wetlands. However, there remains considerable uncertainty regarding the hydro-geochemical pathways and spatiotemporal dynamics of residual H + and metal(loid) mobilisation into the tidal fringe surface waters of these uniquely iron-rich landscapes. Here, we examine the hydrology and water column chemistry across the intertidal slope of a remediating CASS wetland during several tide cycles. There was extreme spatial and temporal dynamism in water column chemistry, with pH fluctuating by ˜3 units (˜3.5-6.5) during a single tide cycle. Acute acidity was spatially confined to the upper intertidal slope, reflecting surface sediment properties, and tidal overtopping is an important pathway for mobilisation of residual H + and Al 3+ to the water column. Marine derived HCO3- was depleted from surface waters migrating across the intertidal slope and a strong gradient in HCO3- was observed from the tidal fringe to the adjacent tributary channel and nearby estuary. Tidal forcing generated oscillating hydraulic gradients in the shallow fringing aquifer, favouring ebb-tide seepage and driving rapid, heterogeneous advection of groundwater on the lower intertidal slope via surface connected macropores. A combination of diffusive and advective flux across the sediment-water interface led to persistent, elevated surface water Fe 2+ (˜10-1000 μM). The geochemical processes associated with Fe 2+ mobilisation displayed distinct spatial zonation, with low pH, proton-promoted desorption occurring on the upper intertidal slope, whilst circum-neutral pH, Fe(III)-reducing processes dominated the lower intertidal slope. Arsenic was also mobilised into surface waters on the lower intertidal slope under moderate pH (˜6.0) conditions and was strongly positively correlated with Fe 2+. Saturation index values for aragonite were substantially depressed (-1 to -5) and significantly negatively correlated with elevation, thereby presenting a barrier to re-colonisation of the upper intertidal slope by calcifying benthic organisms. These findings highlight the spatially complex hydrological and geochemical controls on surface water quality that can occur in tidally inundated acid sulphate soil environments.

Mass wasting deposits in the upper Sehonghong valley, eastern Lesotho: Late Pleistocene climate implications

NASA Astrophysics Data System (ADS)

Mills, S. C.; Grab, S. W.

2009-04-01

Despite considerable research attention on apparent periglacial, glacial and sedimentary phenomena in the Maluti-Drakensberg alpine environment, knowledge on the Quaternary environmental history of this important watershed and climate-divide is still rather rudimentary. The dearth of Quaternary environmental indicators (proxy data) in the high Drakensberg is partly owing to the harsh climate (e.g. high wind speeds and high seasonal precipitation), which offers a poor preservation of past biological remains (e.g. bones, dung, middens, pollen). Possibly the best opportunity to reconstruct high Drakensberg palaeoenvironments is from sedimentary sequences exposed along fluvially-incised valley fills. The upper Sehonghong River (3000 to 3200 m a.s.l.) flows in a westerly direction and is flanked by north- and south-facing slopes reaching 3465 m a.s.l. Sediment is exposed on both the north- and south-facing slopes along the river. Despite uniform regional environmental conditions (geology, topography, climate, vegetation), there is a notable absence of similar north-facing deposits in adjacent upper valley catchments to the north and south of Sehonghong Valley. The upper Sehonghong Valley thus presents somewhat ‘unique' evidence for palaeo-slope mass movement in this alpine region. Thick colluvial deposits are most prominent on the south-facing slopes along the Sehonghong River and occur at altitudes between 3100 m a.s.l. and 3150 m a.s.l. The colluvial mantles are approximately 7 m in thickness, however reach up to 13 m in some areas. Although the north-facing lower valley side-slopes are generally absent of deposits, the notable exception is the thick stratified deposit located a few kilometres upstream. Whilst the south-facing deposits are relatively uniform in nature, the north-facing deposits consist of alternating units of gravel and organic sediment, dated to 36 600 ± 1400 14C yrs BP, and reflecting environmental changes during the Late Pleistocene. Mass wasting deposits support enhanced periglacial activity during the Late Pleistocene, particularly on south-facing slopes, and also where conditions were conducive to enhanced sediment transport on the adjacent north-facing slope of the Sehonghong River. Recent published work has suggested evidence for marginal glaciation in the high Drakensberg within 10 km of the Sehonghong Valley, suggesting that whilst particular environmental settings host deposits classified as glacial moraine, adjacent valleys are occupied by deep (~8 m) valley deposits flanking south-facing slopes. We demonstrate that the variable nature of adjacent valley slope deposits at similar altitudes is a product of a past climate that was within the glacial/periglacial equilibrium zone, and influenced by specific topographic and associated micro-climatic thresholds.

The Effect of Alongcoast Advection on Pacific Northwest Shelf and Slope Water Properties in Relation to Upwelling Variability

NASA Astrophysics Data System (ADS)

Stone, Hally B.; Banas, Neil S.; MacCready, Parker

2018-01-01

The Northern California Current System experiences highly variable seasonal upwelling in addition to larger basin-scale variability, both of which can significantly affect its water chemistry. Salinity and temperature fields from a 7 year ROMS hindcast model of this region (43°N-50°N), along with extensive particle tracking, were used to study interannual variability in water properties over both the upper slope and the midshelf bottom. Variation in slope water properties was an order of magnitude smaller than on the shelf. Furthermore, the primary relationship between temperature and salinity anomalies in midshelf bottom water consisted of variation in density (cold/salty versus warm/fresh), nearly orthogonal to the anomalies along density levels (cold/fresh versus warm/salty) observed on the upper slope. These midshelf anomalies were well-explained (R2 = 0.6) by the combination of interannual variability in local and remote alongshore wind stress, and depth of the California Undercurrent (CUC) core. Lagrangian analysis of upper slope and midshelf bottom water shows that both are affected simultaneously by large-scale alongcoast advection of water through the northern and southern boundaries. The amplitude of anomalies in bottom oxygen and dissolved inorganic carbon (DIC) on the shelf associated with upwelling variability are larger than those associated with typical variation in alongcoast advection, and are comparable to observed anomalies in this region. However, a large northern intrusion event in 2004 illustrates that particular, large-scale alongcoast advection anomalies can be just as effective as upwelling variability in changing shelf water properties on the interannual scale.

The Effect of Alongcoast Advection on Pacific Northwest Shelf and Slope Water Properties in Relation to Upwelling Variability

PubMed Central

Banas, Neil S.; MacCready, Parker

2018-01-01

Abstract The Northern California Current System experiences highly variable seasonal upwelling in addition to larger basin‐scale variability, both of which can significantly affect its water chemistry. Salinity and temperature fields from a 7 year ROMS hindcast model of this region (43°N–50°N), along with extensive particle tracking, were used to study interannual variability in water properties over both the upper slope and the midshelf bottom. Variation in slope water properties was an order of magnitude smaller than on the shelf. Furthermore, the primary relationship between temperature and salinity anomalies in midshelf bottom water consisted of variation in density (cold/salty versus warm/fresh), nearly orthogonal to the anomalies along density levels (cold/fresh versus warm/salty) observed on the upper slope. These midshelf anomalies were well‐explained (R 2 = 0.6) by the combination of interannual variability in local and remote alongshore wind stress, and depth of the California Undercurrent (CUC) core. Lagrangian analysis of upper slope and midshelf bottom water shows that both are affected simultaneously by large‐scale alongcoast advection of water through the northern and southern boundaries. The amplitude of anomalies in bottom oxygen and dissolved inorganic carbon (DIC) on the shelf associated with upwelling variability are larger than those associated with typical variation in alongcoast advection, and are comparable to observed anomalies in this region. However, a large northern intrusion event in 2004 illustrates that particular, large‐scale alongcoast advection anomalies can be just as effective as upwelling variability in changing shelf water properties on the interannual scale. PMID:29938149

Soil Properties and Productivity as Affected by Topsoil Movement within an Eroded Landform

USDA-ARS?s Scientific Manuscript database

In hilly landforms subject to long-term cultivation, erosion has denuded upper slope positions of topsoil and accumulated topsoil in lower slope positions. One approach to remediate these eroded landforms is moving soil from areas of topsoil accumulation to areas of topsoil depletion, termed here so...

Tidal Impacts on Oceanographic and Sea-ice Processes in the Southern Ocean

NASA Astrophysics Data System (ADS)

Padman, L.; Muench, R. D.; Howard, S.; Mueller, R.

2008-12-01

We review recent field and modeling results that demonstrate the importance of tides in establishing the oceanographic and sea-ice conditions in the boundary regions of the Southern Ocean. The tidal component dominates the total oceanic kinetic energy throughout much of the circum-Antarctic seas. This domination is especially pronounced over the continental slope and shelf including the sub-ice-shelf cavities. Tides provide most of the energy that forces diapycnal mixing under ice shelves and thereby contributes to basal melting. The resulting Ice Shelf Water is a significant component of the Antarctic Bottom Water (AABW) filling much of the deep global ocean. Tides exert significant divergent forcing on sea ice along glacial ice fronts and coastal regions, contributing to creation and maintenance of the coastal polynyas where much of the High Salinity Shelf Water component of AABW is formed. Additional tidally forced ice divergence along the shelf break and upper slope significantly impacts area-averaged ice growth and upper-ocean salinity. Tidally forced cross- slope advection, and mixing by the benthic stress associated with tidal currents along the shelf break and upper slope, strongly influence the paths, volume fluxes and hydrographic properties of benthic outflows of dense water leaving the continental shelf. These outflows provide primary source waters for the AABW. These results confirm that general ocean circulation and coupled ocean/ice/atmosphere climate models must incorporate the impacts of tides.

Agro-hydrologic landscapes in the Upper Mississippi and Ohio River basins.

PubMed

Schilling, Keith E; Wolter, Calvin F; McLellan, Eileen

2015-03-01

A critical part of increasing conservation effectiveness is targeting the "right practice" to the "right place" where it can intercept pollutant flowpaths. Conceptually, these flowpaths can be inferred from soil and slope characteristics, and in this study, we developed an agro-hydrologic classification to identify N and P loss pathways and priority conservation practices in small watersheds in the U.S. Midwest. We developed a GIS framework to classify 11,010 small watersheds in the Upper Mississippi and Ohio River basins based on soil permeability and slope characteristics of agricultural cropland areas in each watershed. The amount of cropland in any given watershed varied from <10 to >60 %. Cropland areas were classified into five main categories, with slope classes of <2, 2-5, and >5 %, and soil drainage classes of poorly and well drained. Watersheds in the Upper Mississippi River basin (UMRB) were dominated by cropland areas in low slopes and poorly drained soils, whereas less-intensively cropped watersheds in Wisconsin and Minnesota (in the UMRB) and throughout the Ohio River basin were overwhelmingly well drained. Hydrologic differences in cropped systems indicate that a one-size-fits-all approach to conservation selection will not work. Consulting the classification scheme proposed herein may be an appropriate first-step in identifying those conservation practices that might be most appropriate for small watersheds in the basin.

Space-for-time substitution and the evolution of submarine canyons in a passive, progradational margin.

NASA Astrophysics Data System (ADS)

Micallef, Aaron; Ribó, Marta; Canals, Miquel; Puig, Pere; Lastras, Galderic; Tubau, Xavier

2013-04-01

40% of submarine canyons worldwide are located in passive margins, where they constitute preferential conduits of sediment and biodiversity hotspots. Recent studies have presented evidence that submarine canyons incising passive, progradational margins can co-evolve with the adjacent continental slope during long-term margin construction. The stages of submarine canyon initiation and their development into a mature canyon-channel system are still poorly constrained, however, which is problematic when attempting to reconstruct the development of passive continental margins. In this study we analyse multibeam echosounder and seismic reflection data from the southern Ebro margin (western Mediterranean Sea) to document the stages through which a first-order gully develops into a mature, shelf-breaching canyon and, finally, into a canyon-channel system. This morphological evolution allows the application of a space-for-time substitution approach. Initial gully growth on the continental slope takes place via incision and downslope elongation, with limited upslope head retreat. Gravity flows are the main driver of canyon evolution, whereas slope failures are the main agent of erosion; they control the extent of valley widening, promote tributary development, and their influence becomes more significant with time. Breaching of the continental shelf by a canyon results in higher water/sediment loads that enhance canyon development, particularly in the upper reaches. Connection of the canyon head with a paleo-river changes evolution dynamics significantly, promoting development of a channel and formation of depositional landforms. Morphometric analyses demonstrate that canyons develop into geometrically self-similar systems that approach steady-state and higher drainage efficiency. Canyon activity in the southern Ebro margin is pulsating and enhanced during sea level lowstands. Rapid sedimentation by extension of the palaeo-Millars River into the outermost shelf and upper slope is inferred as the source of gravity flows driving canyon evolution. Canyon morphology is shown to be maintained over the course of more than one fall and rise in sea-level. Our model of canyon evolution is applicable to other passive margins (e.g. Argentine continental margin).

Deep sea sedimentation processes and geomorphology: Northwest Atlantic continental margin

NASA Astrophysics Data System (ADS)

Mosher, David; Campbell, Calvin; Gardner, Jim; Chaytor, Jason; Piper, David; Rebesco, Michele

2017-04-01

Deep-sea sedimentation processes impart a fundamental control on the morphology of the western North Atlantic continental margin from Blake Spur to Hudson Strait. This fact is illustrated by the variable patterns of cross-margin gradients that are based on extensive new multibeam echo-sounder data informed by subbottom profiler and seismic reflection data. Erosion by off-shelf sediment transport in turbidity currents creates gullies, canyons and channels and a steep upper slope. Amalgamation of these conduits produces singular channels and turbidite fan complexes on the lower slope, flattening slope-profile gradients. The effect is an exponentially decaying "graded" slope profile. Comparatively, sediment mass failure produces steeper upper slopes due to head scarp development and a wedging architecture to the lower slope as deposits thin in the downslope direction. This process results in either a "stepped" slope, and/or a significant downslope gradient change where MTDs pinch out. Large drift deposits created by geostrophic currents are developed all along the margin. Blake Ridge, Sackville Spur, and Hamilton Spur are large detached drifts on disparate parts of the margin. They form a linear "above grade" profile along their crests from the shelf to abyssal plain. Deeper portions of the US continental margin are dominated by the Chesapeake Drift and Hatteras Outer Ridge; both plastered elongate mounded drifts. Farther north, particularly on the Grand Banks margin, are plastered and separated drifts. These drifts form "stepped" slope profiles, where they onlap the margin. Trough-mouth fan complexes become more common along the margin with increasing latitude. Sediment deposition and retention, particularly those dominated by glacigenic debris flows, characterize these segments producing an "above grade" slope profile. Understanding these geomorphological consequences of deep sea sedimentation processes is important to extended continental shelf mapping in which gradients and gradient change is a critical metric.

Effects of bedrock geology on source and flowpath of runoff water in steep unchanneled hollows

NASA Astrophysics Data System (ADS)

Uchida, T.; Asano, Y.; Kosugi, K.; Ohte, N.; Mizuyama, T.

2001-05-01

Simultaneous measurements of runoff, soil pore water pressure and soil temperature were taken to evaluate the spatial and temporal nature of flowpaths and flow sources in steep unchanneled hollows in central Japan. Two small hollows were monitored; one is underlain by granite and one is underlain by Paleozoic shale. In both catchments, tensiometers showed that a saturated area formed in the areas near a spring. The soil temperature suggests that in the small perennially saturated area near the spring, water percolating through the vadose zone mixed with water emerging from the bedrock. During rainstorms, the streamflow varied with the soil pore water pressure on the upper slope; the soil pore water pressure in the area near the spring remained nearly constant._@ Moreover, the spring water temperature was almost the same as the transient groundwater temperature on the upper slope. This indicates that the transient groundwater in the upper slope flowed to the spring via lateral preferential paths in both catchments. During summer rainstorms, the soil-bedrock interface temperature increased as the ground became saturated in the granite hollow, suggesting that both rainwater and shallow soil water had important effects on the formation of transient saturated groundwater on the upper slope. That is, it can be concluded that the contribution of the bedrock groundwater to the streamflow was relatively small in the granite hollow during storm runoff. The area where the bedrock groundwater seeped into the soil mantle did not grow in size as the contributing area for the streamflow extended to the upper hollow in the granite catchment. In contrast, the soil temperature indicated that after heavy rainfall (77.5 mm), bedrock groundwater played an important role in the formation of the transient groundwater in the Paleozoic shale hollow. Consequently, the contribution of the bedrock groundwater to the streamflow was relatively large in the shale hollow after heavy rainfall.

Carbonate apron models: Alternatives to the submarine fan model for paleoenvironmental analysis and hydrocarbon exploration

USGS Publications Warehouse

Mullins, H.T.; Cook, H.E.

1986-01-01

Sediment gravity flow deposition along the deep-water flanks of carbonate platforms typically does not produce submarine fans. Rather, wedge-shaped carbonate aprons develop parallel to the adjacent shelf/slope break. The major difference between submarine fans and carbonate aprons is a point source with channelized sedimentation on fans, versus a line source with sheet-flow sedimentation on aprons. Two types of carbonate aprons may develop. Along relatively gentle (< 4??) platform-margin slopes, aprons form immediately adjacent to the shallow-water platform and are referred to as carbonate slope aprons. Along relatively steep (4-15??) platform margin slopes, redeposited limestones accumulate in a base-of-slope setting, by-passing an upper slope via a multitude of small submarine canyons, and are referred to as carbonate base-of-slope aprons. Both apron types are further subdivided into inner and outer facies belts. Inner apron sediments consist of thick, mud-supported conglomerates and megabreccias (Facies F) as well as thick, coarse-grained turbidites (Facies A) interbedded with subordinate amounts of fine-grained, peri-platform ooze (Facies G). Outer apron sediments consist of thinner, grain-supported conglomerates and turbidites (Facies A) as well as classical turbidites (Facies C) with recognizable Bouma divisions, interbedded with approximately equal proportions of peri-platform ooze (Facies G). Seaward, aprons grade laterally into basinal facies of thin, base-cut-out carbonate turbidites (Facies D) that are subordinate to peri-platform oozes (Facies G). Carbonate base-of-slope aprons grade shelfward into an upper slope facies of fine-grained peri-platform ooze (Facies G) cut by numerous small canyons that are filled with coarse debris, as well as intraformational truncation surfaces which result from submarine sliding. In contrast, slope aprons grade shelfward immediately into shoal-water, platform-margin facies without an intervening by-pass slope. The two carbonate apron models presented here offer alternatives to the submarine-fan model for paleoenvironmental analysis and hydrocarbon exploration for mass-transported carbonate facies. ?? 1986.

Preferential flows and soil moistures on a Benggang slope: Determined by the water and temperature co-monitoring

NASA Astrophysics Data System (ADS)

Tao, Yu; He, Yangbo; Duan, Xiaoqian; Zou, Ziqiang; Lin, Lirong; Chen, Jiazhou

2017-10-01

Soil preferential flow (PF) has important effects on rainfall infiltration, moisture distribution, and hydrological and ecological process; but it is very difficult to monitor and characterize on a slope. In this paper, soil water and soil temperature at 20, 40, 60, 80 cm depths in six positions were simultaneously monitored at high frequency to confirm the occurrence of PF at a typical Benggang slope underlain granite residual deposits, and to determine the interaction of soil moisture distribution and Benggang erosion. In the presence of PF, the soil temperature was first (half to one hour) governed by the rainwater temperature, then (more than one hour) governed by the upper soil temperature; in the absence of PF (only matrix flow, MF), the soil temperature was initially governed by the upper soil temperature, then by the rainwater temperature. The results confirmed the water replacement phenomenon in MF, thus it can be distinguished from PF by additional temperature monitoring. It indicates that high frequency moisture and temperature monitoring can determine the occurrence of PF and reveal the soil water movement. The distribution of soil water content and PF on the different positions of the slope showed that a higher frequency of PF resulted in a higher variation of average of water content. The frequency of PF at the lower position can be three times as that of the upper position, therefore, the variation coefficient of soil water content increased from 4.67% to 12.68% at the upper position to 8.18%-33.12% at the lower position, where the Benggang erosion (soil collapse) was more possible. The results suggest strong relationships between PF, soil water variation, and collapse activation near the Benggang wall.

Patterns of Deep-Water Coral Diversity in the Caribbean Basin and Adjacent Southern Waters: An Approach based on Records from the R/V Pillsbury Expeditions

PubMed Central

Hernández-Ávila, Iván

2014-01-01

The diversity of deep-water corals in the Caribbean Sea was studied using records from oceanographic expeditions performed by the R/V Pillsbury. Sampled stations were sorted according to broad depth ranges and ecoregions and were analyzed in terms of species accumulation curves, variance in the species composition and contributions to alpha, beta and gamma diversity. According to the analysis of species accumulation curves using the Chao2 estimator, more diversity occurs on the continental slope (200–2000 m depth) than on the upper continental shelf (60–200 m depth). In addition to the effect of depth sampling, differences in species composition related to depth ranges were detected. However, the differences between ecoregions are dependent on depth ranges, there were fewer differences among ecoregions on the continental slope than on the upper continental shelf. Indicator species for distinctness of ecoregions were, in general, Alcyonaria and Antipatharia for the upper continental shelf, but also the scleractinians Madracis myriabilis and Cladocora debilis. In the continental slope, the alcyonarian Placogorgia and the scleractinians Stephanocyathus and Fungiacyathus were important for the distinction of ecoregions. Beta diversity was the most important component of gamma diversity in the Caribbean Basin. The contribution of ecoregions to alpha, beta and gamma diversity differed with depth range. On the upper continental shelf, the Southern Caribbean ecoregion contributed substantially to all components of diversity. In contrast, the northern ecoregions contributed substantially to the diversity of the Continental Slope. Strategies for the conservation of deep-water coral diversity in the Caribbean Basin must consider the variation between ecoregions and depth ranges. PMID:24671156

Geomorphology and Sediment Stability of a Segment of the U.S. Continental Slope off New Jersey.

PubMed

Robb, J M; Hampson, J C; Twichell, D C

1981-02-27

The morphology of complex deposits of Pleistocene sediments covering the upper continental slope between Lindenkohl Canyon and South Toms Canyon results from both depositional and erosional processes. Small slump or slide features were detected primarily on the flanks of canyons or valleys and were observed to occur only within Pleistocene-aged sediments. Eocene to Miocene sediments are exposed over much of the mid- and lower slope in this area.

Subinertial Slope-Trapped Waves in the Northeastern Gulf of Mexico

DTIC Science & Technology

2009-06-01

describe low-frequency varia- bility in the GOM and its interaction with the topo- graphy. Oey and Lee (2002) describe modeled deep eddy kinetic...deep energy can penetrate onto the upper part of the slope in this region; Oey and Lee (2002) state that their model cannot adequately resolve...slope topography in the NE GOM is described by Cames et al. (2008), Hamilton and Lee (2005), and Wang et al. (2003). Hamilton and Lee (2005) found

Woodland salamander response to two prescribed fires in the central Appalachians

Treesearch

W. Mark Ford; Jane L. Rodrigue; Ella L. Rowan; Steven B. Castleberry; Thomas M. Schuler

2010-01-01

Using coverboard arrays, we monitored woodland salamanders on the Fernow Experimental Forest in the central Appalachian Mountains, West Virginia, USA prior to and following two prescribed fires in mixed oak (Quercus spp.) forest stands. Treatments were burn plots on upper slopes or lower slopes fenced to prevent white-tailed deer (Odocoileus...

Nonmonotonic pressure evolution of the upper critical field in superconducting FeSe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaluarachchi, Udhara S.; Taufour, Valentin; Böhmer, Anna E.

2016-02-01

The pressure dependence of the upper critical field, H c2,c, of single crystalline FeSe was studied using measurements of the interplane resistivity, ρ c, in magnetic fields parallel to tetragonal c axis. H c2,c(T) curves obtained under hydrostatic pressures up to 1.56 GPa, the range over which the superconducting transition temperature, T c, of FeSe exhibits a nonmonotonic dependence with local maximum at p 1 ≈ 0.8 GPa and local minimum at p 2 ≈ 1.2 GPa. The slope of the upper critical field at T c,(dH c2,c/dT)T c, also exhibits a nonmonotonic pressure dependence with distinct changes at pmore » 1 and p 2. For p < p 1 the slope can be described within a multiband orbital model. For both p 1 < p < p 2 and p > p 2 the slope is in good semiquantitative agreement with a single band, orbital Helfand-Werthamer theory with Fermi velocities determined from Shubnikov–de Haas measurements. Lastly, this finding indicates that Fermi surface changes are responsible for the local minimum of T c(p) at p 2 ≈ 1.2 GPa.« less

Final Scientific/Technical Report: Characterizing the Response of the Cascadia Margin Gas Hydrate Reservoir to Bottom Water Warming Along the Upper Continental Slope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solomon, Evan A.; Johnson, H. Paul; Salmi, Marie

The objective of this project is to understand the response of the WA margin gas hydrate system to contemporary warming of bottom water along the upper continental slope. Through pre-cruise analysis and modeling of archive and recent geophysical and oceanographic data, we (1) inventoried bottom simulating reflectors along the WA margin and defined the upper limit of gas hydrate stability, (2) refined margin-wide estimates of heat flow and geothermal gradients, (3) characterized decadal scale temporal variations of bottom water temperatures at the upper continental slope of the Washington margin, and (4) used numerical simulations to provide quantitative estimates of howmore » the shallow boundary of methane hydrate stability responds to modern environmental change. These pre-cruise results provided the context for a systematic geophysical and geochemical survey of methane seepage along the upper continental slope from 48° to 46°N during a 10-day field program on the R/V Thompson from October 10-19, 2014. This systematic inventory of methane emissions along this climate-sensitive margin corridor and comprehensive sediment and water column sampling program provided data and samples for Phase 3 of this project that focused on determining fluid and methane sources (deep-source vs. shallow; microbial, thermogenic, gas hydrate dissociation) within the sediment, and how they relate to contemporary intermediate water warming. During the 2014 research expedition, we sampled nine seep sites between ~470 and 520 m water depth, within the zone of predicted methane hydrate retreat over the past 40 years. We imaged 22 bubble plumes with heights commonly rising to ~300 meters below sea level with one reaching near the sea surface. We collected 22 gravity cores and 20 CTD/hydrocasts from the 9 seeps and at background locations (no acoustic evidence of seepage) within the depth interval of predicted downslope retreat of the methane hydrate stability zone. Approximately 300 pore water samples were extracted from the gravity cores, and the pore water was analyzed for a comprehensive suite of solutes, gases, and stable isotope ratios. This comprehensive geochemical dataset was used to characterize the fluid and gas source(s) at each of the seep sites surveyed. The primary results of this project are: 1) Bottom simulating reflector-derived heat flow values decrease from 95 mW/m2 10 km east of the deformation front to ~60 mW/m2 60 km landward of the deformation front, with anomalously low values of ~25 mW/m2 on a prominent mid-margin terrace off central Washington. 2) The temperature of the incoming sediment/ocean crust interface at the deformation front ranges between 164-179 oC off central Washington, and the 350 oC isotherm at the top of the subducting ocean crust occurs 95 km landward of the deformation front. Differences between BSR-derived heat flow and modeled conductive heat flow suggest mean upward fluid flow rates of 0.4 cm/yr across the margin, with local regions (e.g. fault zones) exhibiting fluid flow rates up to 3.5 cm/yr. 3) A compilation of 2122 high-resolution CTD, glider, and Argo float temperature profiles spanning the upper continental slope of the Washington margin from the years 1968 to 2013 show a long-term warming trend that ranges from 0.006-0.008 oC/yr. Based on this long-term bottom water warming, we developed a 2-D thermal model to simulate the change in sediment temperature distribution over this period, along with the downslope retreat of the methane hydrate stability field. Over the 43 years of the simulation, the thermal disturbance propagated 30 m into the sediment column, causing the base of the methane hydrate stability field to shoal ~13 m and to move ~1 km downslope. 4) A preliminary analysis of seafloor observations and mid-water column acoustic data to detect bubble plumes was used to characterize the depth distribution of seeps along the Cascadia margin. These results indicate high bubble plume densities along the continental shelf at water depths <180 m and at the upper limit of methane hydrate stability along the Washington margin. 5) The majority of the seeps cored during the 2014 research expedition on the R/V Thompson contained abundant authigenic carbonate indicating that they are locations of long-lived seepage rather than emergent seep systems related to methane hydrate dissociation. Despite the evidence for enhanced methane seepage at the upper limit of methane hydrate stability along the Washington margin, we found no unequivocal evidence for active methane hydrate dissociation as a source of fluid and gas at the seeps surveyed. The pore fluid and bottom water chemistry shows that the seeps are fed by a variety of fluid and methane sources, but that methane hydrate dissociation, if occurring, is not widespread and is only a minor source (below the detection limit of our methods). Collectively, these results provide a significant advance in our understanding of the thermal structure of the Cascadia subduction zone and the fluid and methane sources feeding seeps along the upper continental slope of the Washington-sector of the Cascadia margin. Though we did not find unequivocal evidence for methane hydrate dissociation as a source of water and methane at the upper pressure-temperature limit of methane hydrate stability at present, continued warming of North Pacific Intermediate Water in the future has the potential to impact the methane hydrate reservoir in sediments at greater depths along the slope. Thus, this study provides a strong foundation and the necessary characterization of the background state of seepage at the upper limit of methane hydrate stability for future investigations of this important process.« less

Morphobathymetric analysis of the large fine-grained sediment waves over the Gulf of Valencia continental slope (NW Mediterranean)

NASA Astrophysics Data System (ADS)

Ribó, Marta; Puig, Pere; Muñoz, Araceli; Lo Iacono, Claudio; Masqué, Pere; Palanques, Albert; Acosta, Juan; Guillén, Jorge; Gómez Ballesteros, María

2016-01-01

Detailed analysis of recently acquired swath bathymetry, together with high-resolution seismic profiles and bottom sediment samples, revealed the presence of large-scale fine-grained sediment waves over the Gulf of Valencia continental slope. As many other deep-water sediment waves, these features were previously attributed to gravitational slope failure, related to creep-like deformation, and are here reinterpreted as sediment wave fields extending from 250 m depth to the continental rise, at 850 m depth. Geometric parameters were computed from the high-resolution multibeam dataset. Sediment wave lengths range between 500 and 1000 m, and maximum wave heights of up to 50 m are found on the upper slope, decreasing downslope to minimum values of 2 m high. Sediment waves on the lower part of the slope are quasi-stationary vertically accreting, whereas they show an upslope migrating pattern from the mid-slope to the upper part of the continental slope. High-resolution seismic profiles show continuous internal reflectors, with sediment waves merging down-section and sediment wave packages decreasing in thickness downslope. These sediment packages are thicker on the crest of each individual sediment wave and thinner on the downslope flank. 210Pb analyses conducted on sediment cores collected over the sediment wave fields also indicate slightly higher sediment accumulation rates on the wave crests. Sediment wave formation processes have been inferred from contemporary hydrodynamic observations, which reveal the presence of near-inertial internal waves interacting with the Gulf of Valencia continental slope. Internal wave activity is suggested to be the preferential mechanism for the transport and deposition of sediment, and the maintenance of the observed sediment wave fields.

Sediment Pathways Across Trench Slopes: Results From Numerical Modeling

NASA Astrophysics Data System (ADS)

Cormier, M. H.; Seeber, L.; McHugh, C. M.; Fujiwara, T.; Kanamatsu, T.; King, J. W.

2015-12-01

Until the 2011 Mw9.0 Tohoku earthquake, the role of earthquakes as agents of sediment dispersal and deposition at erosional trenches was largely under-appreciated. A series of cruises carried out after the 2011 event has revealed a variety of unsuspected sediment transport mechanisms, such as tsunami-triggered sheet turbidites, suggesting that great earthquakes may in fact be important agents for dispersing sediments across trench slopes. To complement these observational data, we have modeled the pathways of sediments across the trench slope based on bathymetric grids. Our approach assumes that transport direction is controlled by slope azimuth only, and ignores obstacles smaller than 0.6-1 km; these constraints are meant to approximate the behavior of turbidites. Results indicate that (1) most pathways issued from the upper slope terminate near the top of the small frontal wedge, and thus do not reach the trench axis; (2) in turn, sediments transported to the trench axis are likely derived from the small frontal wedge or from the subducting Pacific plate. These results are consistent with the stratigraphy imaged in seismic profiles, which reveals that the slope apron does not extend as far as the frontal wedge, and that the thickness of sediments at the trench axis is similar to that of the incoming Pacific plate. We further applied this modeling technique to the Cascadia, Nankai, Middle-America, and Sumatra trenches. Where well-defined canyons carve the trench slopes, sediments from the upper slope may routinely reach the trench axis (e.g., off Costa Rica and Cascadia). In turn, slope basins that are isolated from the canyons drainage systems must mainly accumulate locally-derived sediments. Therefore, their turbiditic infill may be diagnostic of seismic activity only - and not from storm or flood activity. If correct, this would make isolated slope basins ideal targets for paleoseismological investigation.

Geomorphology of the Eastern North American Continental Margin: the role of deep sea sedimentation processes

NASA Astrophysics Data System (ADS)

Mosher, D. C.; Campbell, C.; Piper, D.; Chaytor, J. D.; Gardner, J. V.; Rebesco, M.

2016-12-01

Deep-sea sedimentation processes impart a fundamental control on the morphology of the western North Atlantic continental margin from Blake Spur to Hudson Strait. This fact is illustrated by the variable patterns of cross-margin gradients that are based on extensive new multibeam echo-sounder data in concert with subbottom profiler and seismic reflection data. Most of the continental margin has a steep (>3o) upper slope down to 1500 to 2500 m and then a gradual middle and lower slope with a general concave upward shape There is a constant interplay of deep sea sedimentation processes, but the general morphology is dictated by the dominant one. Erosion by off-shelf sediment transport in turbidity currents creating channels, gullies and canyons creates the steep upper slope. These gullies and canyons amalgamate to form singular channels that are conduits to the abyssal plain. This process results in a general seaward flattening of gradients, producing an exponentially decaying slope profile. Comparatively, sediment mass failure produces steeper upper slopes due to head scarp development and a wedging architecture to the lower slope as deposits thin in the downslope direction. This process results in either a two-segment slope, and/or a significant downslope gradient change where MTDs pinch out. Large sediment bodies deposited by contour-following currents are developed all along the margin. Blake Ridge, Sackville Spur, and Hamilton Spur are large detached drifts on disparate parts of the margin. Along their crests, they form a linear profile from the shelf to abyssal plain. Deeper portions of the US continental margin are dominated by the Chesapeake Drift and Hatteras Outer Ridge; both plastered elongate mounded drifts. Farther north, particularly on the Grand Banks margin, are plastered and separated drifts. These drifts tend to form bathymetric steps in profile, where they onlap the margin. Stacked drifts create several steps. Turbidites of the abyssal plain onlap the lowermost drift creating a significant gradient change at this juncture. Understanding the geomorphological consequences of deep sea sedimentation processes is important to extended continental shelf mapping, for example, in which gradient change is a critical metric.

Capturing 2D transient surface data of granular flows against obstacles with an RGB-D sensor

NASA Astrophysics Data System (ADS)

Caviedes-Voullieme, Daniel; Juez, Carmelo; Murillo, Javier; Garcia-Navarro, Pilar

2014-05-01

Landslides are an ubiquitous natural hazard, and therefore human infrastructure and settlements are often at risk in mountainous regions. In order to better understand and predict landslides, systematic studies of the phenomena need to be undertaken. In particular, computational tools which allow for analysis of field problems require to be thoroughly tested, calibrated and validated under controlled conditions. And to do so, it is necessary for such controlled experiments to be fully characterized in the same terms as the numerical model requires. This work presents an experimental study of dry granular flow over a rough bed with topography which resembles a mountain valley. It has an upper region with a very high slope. The geometry of the bed describes a fourth order polynomial curve, with a low point with zero slope, and afterwards a short region with adverse slope. Obstacles are present in the lower regions which are used as model geometries of human structures. The experiments consisted of a sudden release a mass of sand on the upper region, and allowing it to flow downslope. Furthermore, it has been frequent in previous studies to measure final states of the granular mass at rest, but seldom has transient data being provided, and never for the entire field. In this work we present transient measurements of the moving granular surfaces, obtained with a consumer-grade RGB-D sensor. The sensor, developed for the videogame industry, allows to measure the moving surface of the sand, thus obtaining elevation fields. The experimental results are very consistent and repeatable. The measured surfaces clearly show the distinctive features of the granular flow around the obstacles and allow to qualitatively describe the different flow patterns. More importantly, the quantitative description of the granular surface allows for benchmarking and calibration of predictive numerical models, key in scaling the small-scale experimental knowledge into the field.

GB-InSAR monitoring of slope deformations in a mountainous area affected by debris flow events

NASA Astrophysics Data System (ADS)

Frodella, William; Salvatici, Teresa; Pazzi, Veronica; Morelli, Stefano; Fanti, Riccardo

2017-10-01

Diffuse and severe slope instabilities affected the whole Veneto region (north-eastern Italy) between 31 October and 2 November 2010, following a period of heavy and persistent rainfall. In this context, on 4 November 2010 a large detrital mass detached from the cover of the Mt. Rotolon deep-seated gravitational slope deformation (DSGSD), located in the upper Agno River valley, channelizing within the Rotolon Creek riverbed and evolving into a highly mobile debris flow. The latter phenomena damaged many hydraulic works, also threatening bridges, local roads, and the residents of the Maltaure, Turcati, and Parlati villages located along the creek banks and the town of Recoaro Terme. From the beginning of the emergency phase, the civil protection system was activated, involving the National Civil Protection Department, Veneto Region, and local administrations' personnel and technicians, as well as scientific institutions. On 8 December 2010 a local-scale monitoring system, based on a ground-based interferometric synthetic aperture radar (GB-InSAR), was implemented in order to evaluate the slope deformation pattern evolution in correspondence of the debris flow detachment sector, with the final aim of assessing the landslide residual risk and managing the emergency phase. This paper describes the results of a 2-year GB-InSAR monitoring campaign (December 2010-December 2012) and its application for monitoring, mapping, and emergency management activities in order to provide a rapid and easy communication of the results to the involved technicians and civil protection personnel, for a better understanding of the landslide phenomena and the decision-making process in a critical landslide scenario.

The role of soil processes in determining mechanisms of slope failure and hillslope development in a humid-tropical forest eastern Puerto Rico

USGS Publications Warehouse

Simon, A.; Larsen, M.C.; Hupp, C.R.

1990-01-01

Translational failures, with associated downslope earthflow components and shallow slides, appear to be the primary mechanism of hillslope denudation in the humid tropical forests of the mountains of eastern Puerto Rico. In-situ weathering of quartz diorite and marine-deposited volcaniclastics produces residual soil (saprolite; up to 21 m deep) / weathered rock profiles. Discontinuous zones of contrasting density and permeability particularly in quartz-diorite slopes at 0.5 m, and between 3 and 7 m, create both pathways and impedances for water that can result in excess pore pressures and, ultimately, aid in determining the location of failure planes and magnitudes of slope failures. In combination with relict fractures which create planes of weakness within the saprolite, and the potential significance of tensile stresses in the upper zone of saprolite (hypothesized to be caused by subsurface soil creep), shear failure can then occur during or after periods of heavy rainfall. Results of in-situ shear-strength testing show negative y-intercepts on the derived Mohr-Coulomb failure envelopes (approximately 50% of all tests) that are interpreted as apparent tensile stresses. Observation of tension cracks 1-2 m deep support the test data. Subsurface soil creep can cause extension of the soil and the development of tensile stresses along upper-slope segments. Shear-strength data support this hypothesis for both geologic types. Apparent values of maximum and mean tensile stress are greatest along upper slopes (16.5 and 6.29 kPa). Previously documented maximum rates of downslope movement coincided with local minima of shear strength, and the shear-strength minimum for all tests was located near 0.5 m below land surface, the shallow zone of contrasting permeabilities. These results indicate that subsurface soil creep, a slow semi-continuous process, may exert a profound influence on rapid, shallow slope failures in saprolitic soils. Data indicate that cove slopes in quartz diorite tend to be the most unstable when saturation levels reach 75%. Deep failures (7 m deep) appear the most critical but not the most frequent because pore pressure build-up will occur more rapidly in the upper perched zone of translocated clays before reaching the lower zone between 3 and 7 m. Frequent shallow failures could reduce the probability of deeper failures by removing overburden and reducing shear stress at depth. Deep failures are more likely to result from storm events of great duration and intensity. Sixty-six 'naturally occurring' and more than 100 'road-related' landslides were mapped. Forest elevations exceed 1000 m, but the majority of these failures were found between 600 and 800 m in elevation. This appears to be the area where there is sufficient concentration of subsurface water to result in excess pore pressures. The high percentage of slope failures in the 600-800-m range, relative to the percentage at higher elevations, suggests that differences in soil-water processes are responsible for the form of these mountain slopes. Steep linear segments are maintained at higher elevations. Slope angles are reduced in the 600-800-m range by frequent shallow slides, creating a largely concave surface. In combination, slope segments above 800 m, and those between 600 and 800 m, produce the characteristic form of the mountains of eastern Puerto Rico. ?? 1990.

Composite biostratigraphy and microfacies analysis of the Upper Jurassic - Lower Cretaceous carbonate platform to slope successions in Sivrihisar (Eskişehir) region (NW Turkey, Pontides): Remarks on the palaeogeographic evolution of the Western Sakarya Zo

NASA Astrophysics Data System (ADS)

Atasoy, Serdar G.; Altıner, Demir; Okay, Aral I.

2017-04-01

Two stratigraphical sections were measured along the Upper Jurassic - Lower Cretaceous carbonate successions exposed in a tectonic klippe of the Sakarya Zone (Pontides), north of Sivrihisar. According to the biozonation and microfacies types, two coeval but dissimiliar rock successions, separated by a thrust fault, have been detected. These successions belong to different depositional belts of the Edremit-Bursa-Bilecik Carbonate Platform (EBBCP), western Sakarya Zone. The lower succession displays a slope to basin facies and consists of the Kimmeridgian - Berriasian Yosunlukbayırı Formation and the overlying Valanginian Soǧukçam Limestone. Within these deposits the following biozones were defined: Globuligerina oxfordiana - Mohlerina basiliensis Zone (Kimmeridgian), Saccocoma Zone (Lower Tithonian), Protopeneroplis ultragranulata Zone (Upper Tithonian), Crassicollaria (massutiana subzone) Zone (uppermost Tithonian), Calpionella (alpina, Remaniella, elliptica subzones) Zone (Lower Berriasian), Calpionellopsis (simplex, oblonga subzones) Zone (Upper Berriasian) and Calpionellites (darderi subzone) Zone (Lower Valanginian). This succession is overthrusted from north to south by another distinct succession characterized by the shallow marine carbonate facies of the Kimmeridgian Günören Formation. Within this unit Labyrinthina mirabilis - Protopeneroplis striata (Kimmeridgian) Zone is recognized. A facies model is proposed for the Sivrihisar transect of the EBBCP for Kimmeridgian - Valanginian interval, based on the distribution of microfacies types. The toe-of-slope facies are characterized by peloidal-bioclastic packstone, mudstone-wackestone and calpionellid/ radiolarian wackestone-packstone comprising pelagic taxa (calpionellids, radiolaria, Globochaete sp., Pithonella sp., Saccocoma sp., calcareous dinocysts, aptychi, very rare planktonic foraminifera and nannoconids) and rare fossil groups transported from the carbonate platform (benthic foraminifera, microencrusters, worm tubes, bivalve, crinoid and echinoid fragments). These deposits represent the background pelagic deposition on the slope. The slope facies are mainly composed of bioclastic-peloidal/ bioclastic-intraclastic packstone, rudstone-grainstone, bioclastic-lithoclastic floatstone-rudstone and reflect generally the increase in the amount of platform derived material (benthic foraminifera, microencrusters, worm tubes, corals, sponges, bryozoa). The matrix of these coarse grained deposits also contains pelagic taxa (calpionellids, radiolaria, Saccocoma sp., Globochaete sp., Pithonella sp., aptyhci). The slope facies are sometimes intercalataed with the toe-of-slope type facies indicating quiescence periods. The shallow marine carbonate platform deposits are characterized by peloidal-intraclastic poorly washed grainstone with bioclasts, bioclastic mudstone-wackestone, intraclastic packstone-rudstone and contain several shallow marine fossils (benthic foraminifera, encrustres and rare echnoid, bivalve and coral fragments) without any pelagic taxa. These carbonates are interpreted as back-reef platform deposits that should not be far away from the platform margin due to the co-occurence of Protopeneroplis striata and Mohlerina basiliensis, abundant in the shelf edge and reefal areas with the complex benthic foraminifera, Labyrinthina mirabilis common in lagoonal areas. If the position of the studied sections with respect to the EBBCP is considered, the studied basin and slope facies should represent the southern platform margin and slope environments of this carbonate platform that faced an ocean to the south during the Jurassic-Cretaceous. The slope and basinal facies overthrusted by the shallow marine deposits in a region situated to the south of the main İzmir-Ankara-Erzincan (İAE) suture suggests an important disruption and shortening of the EBBCP margin and slope deposits related to the closure of the İAE ocean.

Reflection type skin friction meter

NASA Technical Reports Server (NTRS)

Bandyopadhyay, Promode R. (Inventor); Weinstein, Leonard M. (Inventor)

1993-01-01

A housing block is provided having an upper surface conforming to the test surface of a model or aircraft. An oil film is supplied upstream of a transparent wedge window located in this upper surface by an oil pump system located external to the housing block. A light source located within the housing block supplies a light beam which passes through this transparent window and is reflected back through the transparent window by the upper surface of the oil film to a photo-sensitive position sensor located within the housing. This position sensor allows the slope history of the oil film caused by and aerodynamic flow to be determined. The skin friction is determined from this slope history. Internally located mirrors augment and sensitize the reflected beam as necessary before reaching the position sensor. In addition, a filter may be provided before this sensor to filter the beam.

Characterization of the in situ magnetic architecture of oceanic crust (Hess Deep) using near-source vector magnetic data

NASA Astrophysics Data System (ADS)

Tominaga, Masako; Tivey, Maurice A.; MacLeod, Christopher J.; Morris, Antony; Lissenberg, C. Johan; Shillington, Donna J.; Ferrini, Vicki

2016-06-01

Marine magnetic anomalies are a powerful tool for detecting geomagnetic polarity reversals, lithological boundaries, topographic contrasts, and alteration fronts in the oceanic lithosphere. Our aim here is to detect lithological contacts in fast-spreading lower crust and shallow mantle by characterizing magnetic anomalies and investigating their origins. We conducted a high-resolution, near-bottom, vector magnetic survey of crust exposed in the Hess Deep "tectonic window" using the remotely operated vehicle (ROV) Isis during RRS James Cook cruise JC21 in 2008. Hess Deep is located at the western tip of the propagating rift of the Cocos-Nazca plate boundary near the East Pacific Rise (EPR) (2°15'N, 101°30'W). ROV Isis collected high-resolution bathymetry and near-bottom magnetic data as well as seafloor samples to determine the in situ lithostratigraphy and internal structure of a section of EPR lower crust and mantle exposed on the steep (~20°dipping) south facing slope just north of the Hess Deep nadir. Ten magnetic profiles were collected up the slope using a three-axis fluxgate magnetometer mounted on ROV Isis. We develop and extend the vertical magnetic profile (VMP) approach of Tivey (1996) by incorporating, for the first time, a three-dimensional vector analysis, leading to what we here termed as "vector vertical magnetic profiling" approach. We calculate the source magnetization distribution, the deviation from two dimensionality, and the strike of magnetic boundaries using both the total field Fourier-transform inversion approach and a modified differential vector magnetic analysis. Overall, coherent, long-wavelength total field anomalies are present with a strong magnetization contrast between the upper and lower parts of the slope. The total field anomalies indicate a coherently magnetized source at depth. The upper part of the slope is weakly magnetized and magnetic structure follows the underlying slope morphology, including a "bench" and lobe-shaped steps, imaged by microbathymetry. The lower part of the slope is strongly magnetized, with a gradual reduction in amplitude from east to west across the slope. Surface morphology and recent drilling results indicate that the slope has been affected by mass wasting, but the observation of internally coherent magnetization distributions within the upper and lower slopes suggest that the disturbance is surficial. We attribute the spatial differences in magnetization distribution to the combination of changes in in situ lithology and depth to the source. These survey lines document the first magnetic profiles that capture the gabbro-ultramafic and possibly dike-gabbro boundaries in fast-spreading lower crust.

Using U-Pb Detrital Zircon to Identify Evolution of Sediment Drainage in the South Central Pyrenean Foreland Basin, Spain

NASA Astrophysics Data System (ADS)

Clark, J. D.; Stockli, D. F.; McKay, M. P.; Thomson, K.; Puigdefabregas, C.; Castelltort, S.; Dykstra, M.; Fildani, A.

2014-12-01

Until the 2011 Mw9.0 Tohoku earthquake, the role of earthquakes as agents of sediment dispersal and deposition at erosional trenches was largely under-appreciated. A series of cruises carried out after the 2011 event has revealed a variety of unsuspected sediment transport mechanisms, such as tsunami-triggered sheet turbidites, suggesting that great earthquakes may in fact be important agents for dispersing sediments across trench slopes. To complement these observational data, we have modeled the pathways of sediments across the trench slope based on bathymetric grids. Our approach assumes that transport direction is controlled by slope azimuth only, and ignores obstacles smaller than 0.6-1 km; these constraints are meant to approximate the behavior of turbidites. Results indicate that (1) most pathways issued from the upper slope terminate near the top of the small frontal wedge, and thus do not reach the trench axis; (2) in turn, sediments transported to the trench axis are likely derived from the small frontal wedge or from the subducting Pacific plate. These results are consistent with the stratigraphy imaged in seismic profiles, which reveals that the slope apron does not extend as far as the frontal wedge, and that the thickness of sediments at the trench axis is similar to that of the incoming Pacific plate. We further applied this modeling technique to the Cascadia, Nankai, Middle-America, and Sumatra trenches. Where well-defined canyons carve the trench slopes, sediments from the upper slope may routinely reach the trench axis (e.g., off Costa Rica and Cascadia). In turn, slope basins that are isolated from the canyons drainage systems must mainly accumulate locally-derived sediments. Therefore, their turbiditic infill may be diagnostic of seismic activity only - and not from storm or flood activity. If correct, this would make isolated slope basins ideal targets for paleoseismological investigation.

Erosion Rates of Volcanic-ash Derived Soils in the Blue Mountains of Eastern Oregon, USA: A Comparison Across Sales in Space and Time.

NASA Astrophysics Data System (ADS)

Wondzell, S. M.; Clifton, C. F.; Harris, R. M.; Ritchie, J. C.

2007-12-01

We examined present day rates of erosion in the Blue Mountains of eastern Oregon to quantify background erosion rates to provide standards for assessing possible accelerated rates of erosion resulting from wild fire or from land-management activities such as prescribed fire. The Skookum Creek watersheds, where stream discharge and sediment yield have been recorded continuously since the watersheds were gauged in 1992, provided a watershed-scale estimate of erosion rates. We installed hillslope erosion plots on north- and south- facing slopes within the watersheds in 2002 and collected data for three years to estimate short-term, hillslope- scale erosion rates. We also collected soil samples and analyzed them for 137Cs to get a 40-yr time- integrated estimate of hillslope erosion rates. Our results showed large differences between whole-watershed sediment yields and hillslope erosion rates measured from plots, suggesting that episodic processes dominated sediment production and transport and therefore controlled watershed-scale sediment budgets. At the hillslope-scale, short-term erosion resulted primarily from digging by small mammals and trampling by elk. Visual observations at the plots suggested that annual down-slope sediment movement was usually less than one meter. There were no significant difference among slope positions, but erosion rates were significantly higher on south-facing aspects and positively correlated to the amount of bare ground. In contrast, the 137Cs data suggested that erosion rates differed with slope position. Higher erosion rates were measured in toe- and mid-slope positions, with little erosion occurring on upper slopes and ridge tops. We examine these results in light of the present-day pattern of surface soils resulting from redistribution of volcanic ash from upper- slope to lower-slope positions and the effects of disturbance, including wildfire and the preferential grazing of riparian and lower-slope positions by domestic livestock.

Controls on size and occurrence of the largest sub-aerial landslide on Earth: Seymareh (Saidmarreh) landslide, Zagros fold-thrust belt, Iran

NASA Astrophysics Data System (ADS)

Roberts, N. J.; Evans, S. G.

2009-12-01

Gigantic (> 1 Gm3) landslides are high-magnitude, low-frequency extremes of mass movements. They are important factors in topographic evolution and hazard in mountain regions due to their magnitude. However, few examples exist for study because of their infrequency. Consequently, controls on the location and size gigantic landslides remain poorly understood. Re-examination of the Seymareh (Saidmarreh) rock avalanche, Zagros fold-thrust belt, shows it to be the largest sub-aerial landslide on Earth (initial failure volume 38 Gm3), thus representing the upper magnitude limit for terrestrial landslides. Detailed examination of the source area (including orbital remote sensing, geotechnical investigation and structural mapping) provides new insights into controls on the size and mobility of gigantic landslides. The gigantic Early Holocene rockslide initiated on the northeast limb of Kabir Kuh, the largest anticline in the Zagros fold-thrust belt, and involved the simultaneous failure of a rock mass measuring 15 km along strike. The rockslide transformed into a rock avalanche that ran-out 19.0 km, filling two adjacent valleys and overtopping an intervening low mountain ridge. The failure involved 220 m of competent jointed limestone (Asmari Formation) underlain by 580 m of weaker mudrock-dominated units. Geologic structure, geomechanical strength and topography of the source slope strongly controlled failure initiation. Extreme landslide dimensions resulted in part from extensive uniform pre-failure stability, produced by structural and topographic features related to the large scale of the Kabir Kuh anticline. High continuity bedding planes determined the large lateral extent along strike. Bedding normal joints, the breached nature of the anticline and fluvial undercutting at the slope toe accommodated expansive lateral, headscarp and toe release, respectively, necessary for extensive failure. Geomechanically weak units at depth aided the penetration of the failure surface into the source slope while low bedding dip (ca. 19°) allowed kinematic freedom of a particularly thick sequence to move downslope. Prevention of gradual rockmass removal by smaller-magnitude, more frequent denudation ensured its preservation for later simultaneous failure. The overall failure surface (11°) cut across weaker beds and finally breached the Asmari carapace by break-out at the base of the source slope. Relative relief of the source slope on Kabir Kuh was modest (1350 m on average) indicating that uniform structural and topographic conditions along strike, shallow bedding dips, and the geomechnical properties of the source rock mass were more important in determining the magnitude of the landslide that forms the upper magnitude limit for subaerial landslides.

Statewide Geotechnical Asset Management Program Development : Final Report for Rock Slopes, Unstable Soil Slopes and Embankments, Retaining Walls, and Material Sites

DOT National Transportation Integrated Search

2017-09-05

The Alaska Department of Transportation and Public Facilities (AKDOT&PF) has developed the nations first Geotechnical Asset Management Program. The program encompasses rock slopes, unstable slopes and embankments, retaining walls, and material sou...

Evidence for Recent Liquid Water on Mars: Gullies at 70oS in Polar Pit Walls

NASA Technical Reports Server (NTRS)

2000-01-01

[figure removed for brevity, see original site]

Gully landforms proposed to have been caused by geologically-recent seepage and runoff of liquid water on Mars are found in the most unlikely places. They typically occur in areas that are quite cold--well below freezing--all year round. Like the old adage about moss on trees, nearly all of them form on slopes that face away from sunlight. Most of the gullies occur at latitudes between 30o and 70o.

The highest latitude at which martian gullies have been found is around 70o-75oS on the walls of pits developed in the south polar pitted plains. If you were at this same latitude on Earth, you would be in Antarctica. This region spends much of the winter--which lasts approximately 6 months on Mars--in darkness and at temperatures cold enough to freeze carbon dioxide (around -130oC or -200oF). Nevertheless, gullies with very sharp, deep, v-shaped channels are seen on the pit walls (above, left).

Based upon the locations of the tops of the channels on the slope shown here, the inferred site of liquid seepage is located at a layer in the pit wall about 1/3 of the way down from the top of the MOC image. The channels start wide and taper downslope. The area above the channels is layered and has been eroded by mass movement--dry avalanching of debris--to form a pattern of chutes and ridges on the upper slope of the pit wall. The top layer appears to have many boulders in it (each about the size of a small house), these boulders are left behind on the upper slopes of the pit wall as debris is removed.

Centered near 70.7oS, 355.7oW, the MOC image was acquired July 14, 1999, and covers an area approximately 2.8 km (1.7 mi) wide by 2.1 km (1.3 mi) high. Sunlight illuminates the MOC image from the upper left and north is toward the upper left. The context view (right) is from the Viking 2 orbiter and was acquired in 1977. The Viking picture is illuminated from the top/upper left; north is toward the upper right. The small white box in the context frame (upper right corner) shows the location of the high resolution MOC view.

Distribution, reproduction, and feeding of West African shrimp Plesionika carinata Holthuis, 1951 (Decapoda, Pandalidae)

NASA Astrophysics Data System (ADS)

Burukovsky, R. N.

2017-09-01

Plesionika carinata is endemic in the West African tropical biogeographical realm and is distributed from the western Sahara coast (23°35' N) to southern Namibia (29° S). A total of 263 individuals with a total carapace length of 31 to 71 mm have been studied. P. carinata juveniles are pelagic and occur over depths from 340 to 2000 m or more, mainly over the lower part of the continental slope in summer and over the upper part of the continental slope in autumn. Adults are mainly benthic and occur on the edge of the shelf and the upper part of the continental slope (at depths of 300 to 880 m). Ovigerous females have 750 to 3330 eggs 0.45-0.5 × 0.5-0.65 mm in size on pleopods. Plesionika carinata feeds on abundant micronectonic and macroplanktonic crustaceans (euphausiids and pelagic shrimps) at earlier pelagic stages; it is detritophagous/necrophagous and predatory near the bottom when adult.

Impact of structural and autocyclic basin-floor topography on the depositional evolution of the deep-water Valparaiso forearc basin, central Chile

USGS Publications Warehouse

Laursen, J.; Normark, W.R.

2003-01-01

The Valparaiso Basin constitutes a unique and prominent deep-water forearc basin underlying a 40-km by 60-km mid-slope terrace at 2.5-km water depth on the central Chile margin. Seismic-reflection data, collected as part of the CONDOR investigation, image a 3-3.5-km thick sediment succession that fills a smoothly sagged, margin-parallel, elongated trough at the base of the upper slope. In response to underthrusting of the Juan Ferna??ndez Ridge on the Nazca plate, the basin fill is increasingly deformed in the seaward direction above seaward-vergent outer forearc compressional highs. Syn-depositional growth of a large, margin-parallel monoclinal high in conjunction with sagging of the inner trough of the basin created stratal geometries similar to those observed in forearc basins bordered by large accretionary prisms. Margin-parallel compressional ridges diverted turbidity currents along the basin axis and exerted a direct control on sediment depositional processes. As structural depressions became buried, transverse input from point sources on the adjacent upper slope formed complex fan systems with sediment waves characterising the overbank environment, common on many Pleistocene turbidite systems. Mass failure as a result of local topographic inversion formed a prominent mass-flow deposit, and ultimately resulted in canyon formation and hence a new focused point source feeding the basin. The Valparaiso Basin is presently filled to the spill point of the outer forearc highs, causing headward erosion of incipient canyons into the basin fill and allowing bypass of sediment to the Chile Trench. Age estimates that are constrained by subduction-related syn-depositional deformation of the upper 700-800m of the basin fill suggest that glacio-eustatic sea-level lowstands, in conjunction with accelerated denudation rates, within the past 350 ka may have contributed to the increase in simultaneously active point sources along the upper slope as well as an increased complexity of proximal depositional facies.

Playing with inclined circular hydraulic jumps

NASA Astrophysics Data System (ADS)

Lebon, Luc; Saget, Beryl; Durand, Marc; Limat, Laurent; Couder, Yves; Receveur, Mathieu

2008-11-01

We have investigated the structure of the circular hydraulic jump, when the jet impacts an inclined plate. At low plate slope, quasi-circular shapes, evolving towards elliptic shapes are observed. At moderate inclinations, the upper and lower jumps become markedly different, and the lower jump is even rejected to infinity when a critical inclination is reached. Above this critical inclination, the jump is coupled to an outer dewetting contact line to give a specific object (expanding impact sheet feeding a curved rim in which the liquid is flowing tangentially). In this regime, both the position and curvature of the upper jump follows unusual scalings with the flow rate that completely differ from those observed on horizontal plates. Finally we have looked to metastable drops trapped in the circular jump at very small inclinations. As reported in a previous APS, the lowest position in the jump can become unstable and the drops oscillate around the jump perimeter. We show that this behavior requires very specific conditions of surface tension and viscosity and propose simple interpretations for the instability mechanism.

How to Drive a Car on a Snowy Slope

ERIC Educational Resources Information Center

Ogawara, Yasuo

2016-01-01

When I was a freshman at Tokyo University of Science, my senpai (upper-class student mentor) took me to a certain skiing ground in his car, which was equipped with standard tires. He tried to enter the parking area there, but his car could not climb a short slope leading to the entrance. I would like to describe here how he dealt with the problem…

Influence of slope on fire spread rate

Treesearch

B.W. Butler; W.R. Anderson; E.A. Catchpole

2007-01-01

Data demonstrate the effect of slope on heading and backing fires burning through woody fuels. The data indicate that the upper limit of heading fire rate of spread is defined by the rate of spread up a vertical fuel array, and the lower limit is defined by the rate of spread of a backing fire burning downslope. The minimum spread rate is found to occur at nominally --...

Lunar Roving Vehicle parked in lunar depression on slope of Stone Mountain

NASA Technical Reports Server (NTRS)

1972-01-01

The Lunar Roving Vehicle appears to be parked in a deep lunar depression on the slope of Stone Mountain in this photograph of the lunar scene at Station no. 4, taken during the second Apollo 16 extravehicular activity (EVA-2) at the Descartes landing site. A sample collection bag is in the right foreground. Note field of small boulders at upper right.

Large-scale diversity of slope fishes: pattern inconsistency between multiple diversity indices.

PubMed

Gaertner, Jean-Claude; Maiorano, Porzia; Mérigot, Bastien; Colloca, Francesco; Politou, Chrissi-Yianna; Gil De Sola, Luis; Bertrand, Jacques A; Murenu, Matteo; Durbec, Jean-Pierre; Kallianiotis, Argyris; Mannini, Alessandro

2013-01-01

Large-scale studies focused on the diversity of continental slope ecosystems are still rare, usually restricted to a limited number of diversity indices and mainly based on the empirical comparison of heterogeneous local data sets. In contrast, we investigate large-scale fish diversity on the basis of multiple diversity indices and using 1454 standardized trawl hauls collected throughout the upper and middle slope of the whole northern Mediterranean Sea (36°3'- 45°7' N; 5°3'W - 28°E). We have analyzed (1) the empirical relationships between a set of 11 diversity indices in order to assess their degree of complementarity/redundancy and (2) the consistency of spatial patterns exhibited by each of the complementary groups of indices. Regarding species richness, our results contrasted both the traditional view based on the hump-shaped theory for bathymetric pattern and the commonly-admitted hypothesis of a large-scale decreasing trend correlated with a similar gradient of primary production in the Mediterranean Sea. More generally, we found that the components of slope fish diversity we analyzed did not always show a consistent pattern of distribution according either to depth or to spatial areas, suggesting that they are not driven by the same factors. These results, which stress the need to extend the number of indices traditionally considered in diversity monitoring networks, could provide a basis for rethinking not only the methodological approach used in monitoring systems, but also the definition of priority zones for protection. Finally, our results call into question the feasibility of properly investigating large-scale diversity patterns using a widespread approach in ecology, which is based on the compilation of pre-existing heterogeneous and disparate data sets, in particular when focusing on indices that are very sensitive to sampling design standardization, such as species richness.

75 FR 65366 - Recovery Policy RP9524.2, Landslides and Slope Stability Related to Public Facilities

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-22

...] Recovery Policy RP9524.2, Landslides and Slope Stability Related to Public Facilities AGENCY: Federal... the final Recovery Policy RP9524.2, Landslides and Slope Stability Related to Public Facilities, which... facilities threatened by landslides or slope failures; as well as the eligibility of permanent repairs to...

Impact of Soil Composition and Electrochemistry on Corrosion of Rock-cut Slope Nets along Railway Lines in China.

PubMed

Chen, Jiao; Chen, Zhaoqiong; Ai, Yingwei; Xiao, Jingyao; Pan, Dandan; Li, Wei; Huang, Zhiyu; Wang, Yumei

2015-10-09

Taking the slope of Suiyu Railway to study, the research separately studied soil resistivity, soil electrochemistry (corrosion potential, oxidization reduction potential, electric potential gradient and pH), soil anions (total soluble salt, Cl(-), SO4(2-) and ), and soil nutrition (moisture content, organic matter, total nitrogen, alkali-hydrolysable nitrogen, available phosphorus, and available potassium) at different slope levels, and conducted corrosion grade evaluation on artificial soil according to its single index and comprehensive indexes. Compared with other factors, water has the biggest impact on the corrosion of slope protection net, followed by anion content. Total soluble salt has the moderate impact on the corrosion of slope protection net, and stray current has the moderate impact on the corrosion of mid-slope protection net. Comprehensive evaluation on the corrosive degree of soil samples indicates that the corrosion of upper slope is moderate, and the corrosion of mid-slope and lower slope is strong. Organic matter in soil is remarkably relevant to electric potential gradient. Available nitrogen, available potassium and available phosphorus are remarkably relevant to anions. The distribution of soil nutrient is indirectly relevant to slope type.

Impact of Soil Composition and Electrochemistry on Corrosion of Rock-cut Slope Nets along Railway Lines in China

PubMed Central

Chen, Jiao; Chen, Zhaoqiong; Ai, Yingwei; Xiao, Jingyao; Pan, Dandan; Li, Wei; Huang, Zhiyu; Wang, Yumei

2015-01-01

Taking the slope of Suiyu Railway to study, the research separately studied soil resistivity, soil electrochemistry (corrosion potential, oxidization reduction potential, electric potential gradient and pH), soil anions (total soluble salt, Cl−, SO42− and ), and soil nutrition (moisture content, organic matter, total nitrogen, alkali-hydrolysable nitrogen, available phosphorus, and available potassium) at different slope levels, and conducted corrosion grade evaluation on artificial soil according to its single index and comprehensive indexes. Compared with other factors, water has the biggest impact on the corrosion of slope protection net, followed by anion content. Total soluble salt has the moderate impact on the corrosion of slope protection net, and stray current has the moderate impact on the corrosion of mid-slope protection net. Comprehensive evaluation on the corrosive degree of soil samples indicates that the corrosion of upper slope is moderate, and the corrosion of mid-slope and lower slope is strong. Organic matter in soil is remarkably relevant to electric potential gradient. Available nitrogen, available potassium and available phosphorus are remarkably relevant to anions. The distribution of soil nutrient is indirectly relevant to slope type. PMID:26450811

Does permanent extensional deformation in lower forearc slopes indicate shallow plate-boundary rupture?

NASA Astrophysics Data System (ADS)

Geersen, J.; Ranero, C. R.; Kopp, H.; Behrmann, J. H.; Lange, D.; Klaucke, I.; Barrientos, S.; Diaz-Naveas, J.; Barckhausen, U.; Reichert, C.

2018-05-01

Seismic rupture of the shallow plate-boundary can result in large tsunamis with tragic socio-economic consequences, as exemplified by the 2011 Tohoku-Oki earthquake. To better understand the processes involved in shallow earthquake rupture in seismic gaps (where megathrust earthquakes are expected), and investigate the tsunami hazard, it is important to assess whether the region experienced shallow earthquake rupture in the past. However, there are currently no established methods to elucidate whether a margin segment has repeatedly experienced shallow earthquake rupture, with the exception of mechanical studies on subducted fault-rocks. Here we combine new swath bathymetric data, unpublished seismic reflection images, and inter-seismic seismicity to evaluate if the pattern of permanent deformation in the marine forearc of the Northern Chile seismic gap allows inferences on past earthquake behavior. While the tectonic configuration of the middle and upper slope remains similar over hundreds of kilometers along the North Chilean margin, we document permanent extensional deformation of the lower slope localized to the region 20.8°S-22°S. Critical taper analyses, the comparison of permanent deformation to inter-seismic seismicity and plate-coupling models, as well as recent observations from other subduction-zones, including the area that ruptured during the 2011 Tohoku-Oki earthquake, suggest that the normal faults at the lower slope may have resulted from shallow, possibly near-trench breaking earthquake ruptures in the past. In the adjacent margin segments, the 1995 Antofagasta, 2007 Tocopilla, and 2014 Iquique earthquakes were limited to the middle and upper-slope and the terrestrial forearc, and so are upper-plate normal faults. Our findings suggest a seismo-tectonic segmentation of the North Chilean margin that seems to be stable over multiple earthquake cycles. If our interpretations are correct, they indicate a high tsunami hazard posed by the yet un-ruptured southern segment of the seismic gap.

A regional assessment of potential environmental hazards to and limitations on petroleum development of the Southeastern United States Atlantic continental shelf, slope, and rise, offshore North Carolina

USGS Publications Warehouse

Popenoe, Peter; Coward, E.L.; Cashman, K.V.

1982-01-01

More than 11,000 km of high-resolution seismic-reflection data, 325 km of mid-range sidescan-sonar data, and 500 km of long-range sidescan-sonar data were examined and used to construct an environmental geology map of the Continental Shelf, Slope, and Rise for the area of the U.S. Atlantic margin between lats. 32?N. and 37?N. Hardgrounds and two faults described in previous literature also are shown on the map. On the Continental Shelf, at least two faults, the Helena Banks fault and the White Oak lineament, appear to be tectonic in origin. However, a lack of historical seismicity associated with these faults indicates that they are probably not active at the present time. Hardgrounds are widely scattered but are most abundant in Onslow Bay. Although paleostream channels are common nearshore, they do not appear to be common on the central and outer shelf except off Albemarle Sound where extensive Pleistocene, Pliocene, and late Miocene channels extend across the shelf. Mobile bottom sediments are confined mainly to the shoals off Cape Romain, Cape Fear, Cape Lookout, and Cape Hatteras. Elsewhere the sand cover is thin, and older more indurated rocks are present in subcrop. No slope-instability features were noted on the Florida-Hatteras slope off North Carolina. The lack of features indicates that this slope is relatively stable. Evidence for scour by strong currents is ubiquitous on the northern Blake Plateau although deep-water reefs are sparse. The outer edge of the plateau is dominated by a major growth fault and numerous splay and antithetic faults. These faults are the product of salt tectonism in the Carolina trough and thus are not associated with seismicity. Displacements observed near the sea floor and breached diapirs offshore indicate that the main fault is still moving. Associated with the faults are collapse features that are interpreted to be caused by karst solution and cavernous porosity in Eocene and Oligocene limestones at depth. Major slumps have taken place in two large areas of the Continental Slope. Seismic-reflection profiles of the southern area, centered on the lower slope at 1at. 33?N., long. 76?W., show a 80-m-hlgh scarp in which bedding has been truncated. Rotational slump faults are present in this area on the middle and upper slope. Sidescan images show that large blocks have slid downslope from the scarp face, furrowing the bottom. High-resolution (3.5-kHz) records show that the rotational slump faults upslope are active. The association of these slumps and the scarps with salt diapirs suggests subsidence accompanying salt tectonism as the cause. Seismic-reflection records over the northern area, at about fat. 36?20'N., long. 74?40'W., show two steep scarps, each about 225 m high on the upper and middle-slope. These slump scars and an absence of Pleistocene sediments indicate that large blocks of the slope have been removed by slumping. The slope north of fat. 35?N. is highly dissected by canyons. Mid-range sidescan-sonar records suggest that the canyons are the product of mass wasting and have probably formed largely by slumping. Sediments in a wide zone on the upper rise are highly disturbed and faulted owing to salt tectonism. Twenty-six salt diapirs are mapped, as is a zone of disturbed bottom related to salt tectonism. An area of frozen bottom (clathrate) under which shallow free gas is trapped underlies the outer Blake Plateau, the slope, and the upper rise. Although the hazards of drilling into or through clathrates have not been tested, the release of gas from beneath this frozen layer may prove to be a primary hazard to exploration.

Using (137)Cs to quantify the redistribution of soil organic carbon and total N affected by intensive soil erosion in the headwaters of the Yangtze River, China.

PubMed

Guoxiao, Wei; Yibo, Wang; Yan Lin, Wang

2008-12-01

Characteristics of soil organic carbon (SOC) and total nitrogen (total N) are important for determining the overall quality of soils. Studies on spatial and temporal variation in SOC and total N are of great importance because of global environmental concerns. Soil erosion is one of the major processes affecting the redistribution of SOC and total N in the test fields. To characterize the distribution and dynamics of SOC and N in the intensively eroded soil of the headwaters of the Yangtze River, China, we measured profiles of soil organic C, total N stocks, and (137)Cs in a control plot and a treatment plot. The amounts of SOC, (137)Cs of sampling soil profiles increased in the following order, lower>middle>upper portions on the control plot, and the amounts of total N of sampling soil profile increase in the following order: upper>middle>lower on the control plot. Intensive soil erosion resulted in a significant decrease of SOC amounts by 34.9%, 28.3% and 52.6% for 0-30cm soil layer at upper, middle and lower portions and (137)Cs inventory decreased by 68%, 11% and 85% at upper, middle and lower portions, respectively. On the treatment plot total N decreased by 50.2% and 14.6% at the upper and middle portions and increased by 48.9% at the lower portion. Coefficients of variation (CVs) of SOC decreased by 31%, 37% and 30% in the upper, middle and lower slope portions, respectively. Similar to the variational trend of SOC, CVs of (137)Cs decreased by 19.2%, 0.5% and 36.5%; and total N decreased by 45.7%, 65.1% and 19% in the upper, middle and lower slope portions, respectively. The results showed that (137)Cs, SOC and total N moved on the sloping land almost in the same physical mechanism during the soil erosion procedure, indicating that fallout of (137)Cs could be used directly for quantifying dynamic SOC and total N redistribution as the soil was affected by intensive soil erosion.

Environmental drivers of megafaunal assemblage composition and biomass distribution over mainland and insular slopes of the Balearic Basin (Western Mediterranean)

NASA Astrophysics Data System (ADS)

Fanelli, E.; Cartes, J. E.; Papiol, V.; López-Pérez, C.

2013-08-01

The influence of mesoscale physical and trophic variables on deep-sea megafauna, a scale of variation often neglected in deep-sea studies, is crucial for understanding their role in the ecosystem. Drivers of megafaunal assemblage composition and biomass distribution have been investigated in two contrasting areas of the Balearic basin in the NW Mediterranean: on the mainland slope (Catalonian coasts) and on the insular slope (North of Mallorca, Balearic Islands). An experimental bottom trawl survey was carried out during summer 2010, at stations in both sub-areas located between 450 and 2200 m water depth. Environmental data were collected simultaneously: near-bottom physical parameters, and the elemental and isotopic composition of sediments. Initially, data were analysed along the whole depth gradient, and then assemblages from the two areas were compared. Analysis of the trawls showed the existence of one group associated with the upper slope (US=450-690 m), another with the middle slope (MS=1000-1300 m) and a third with the lower slope (LS=1400-2200 m). Also, significant differences in the assemblage composition were found between mainland and insular slopes at MS. Dominance by different species was evident when the two areas were compared by SIMPER analysis. The greatest fish biomass was recorded in both areas at 1000-1300 m, a zone linked to minimum temperature and maximum O2 concentration on the bottom. Near the mainland, fish assemblages were best explained (43% of total variance, DISTLM analysis) by prey availability (gelatinous zooplankton biomass). On the insular slope, trophic webs seemed less complex and were based on vertical input of surface primary production. Decapods, which reached their highest biomass values on the upper slope, were correlated with salinity and temperature in both the areas. However, while hydrographic conditions (temperature and salinity) seemed to be the most important variables over the insular slope, resource availability (gelatinous zooplankton and Calocaris macandreae) predominated and explained 59% of decapod assemblage variation over the mainland slope. Both fish and decapods were linked to net primary production recorded over the mainland 3 months before sampling, while the delay between the input of food from the surface and fish abundance was only 1 month on the insular slope. Our results suggest that trophic relationships over insular slopes probably involve a shorter food chain than over mainland slopes and one that is likely more efficient in terms of energy transfer.

Comparative geochemistry of Indian margin (Arabian Sea) sediments: Estuary to continental slope.

NASA Astrophysics Data System (ADS)

Cowie, Greg; Mowbray, Stephen; Kurian, Siby; Sarkar, Amit; White, Carol; Anderson, Amy; Vergnaud, Bianca; Johnstone, Gisele; Brear, Samuel; Woulds, Clare; Naqvi, Wajih; Kitazato, Hiroshi

2014-05-01

Factors controlling the distribution of organic matter in the Arabian Sea have been the subject of much research and debate ever since organic-rich slope deposits were associated with the mid-water oxygen minimum zone (OMZ) However, the debate remains open, and numerous interacting factors have been invoked as important controls. A limitation of most previous studies is that they have been restricted to limited portions of the margin, and have not included molecular-level tracers that allow distinction of organic matter (OM) source and degradation state as factors in OM distribution. We report results from sites across the Indian margin of the Arabian Sea, which were analysed for carbon and nitrogen compositions (elemental and isotopic), grain size and indices of OM source and degradation state. Site locations ranged from the Mandovi/Zuari estuaries to depths of ~2000m on the continental slope, thus spanning both the semi-permanent OMZ on the upper slope (~200-1300m) and the seasonal hypoxic zone that impinges on the shelf. Source indices showed mixed marine and terrigenous OM within the estuaries, but overwhelming predominance (80%+) of marine OM on the shelf and slope, even in nearshore deposits. Thus, riverine OM is heavily diluted or efficiently remineralised within or immediately offshore of the estuaries. Any terrigenous OM that is exported appears to be retained in nearshore muds; lignin phenols indicate that the small terrigenous OM content of slope sediments is of different origin, potentially from rivers to the north. Organic C contents of surface shelf and slope sediments varied from <0.5 wt% in relict shelf sands to a maximum of >7 wt% at upper slope sites within the OMZ, then decreasing to ≤1wt% at 2000m. However, major variability (~5 wt%) occured within the OMZ at sites with near-identical depths and bottom-water oxygen. A strong relationship between organic C and grain size was seen for OMZ sediments, but lower C loadings were found for sites on the shelf and below the OMZ. Diagenetic indices confirmed that lower C content below the OMZ is associated with greater extent of OM degradation, but that C-poor shelf sediments are not consistently more degraded than those within the OMZ. Together, results indicate that OM enrichment on the upper slope, where it occurs, can be explained by winnowing or other physical processes on the shelf combined with progressive OM degradation with increasing oxygen exposure below the OMZ. Reduced oxygen exposure may contribute to observed OM enrichment with the OMZ, but hydrodynamic processes are the overriding control on sediment OM distribution, even within the OMZ.

How to Drive a Car on a Snowy Slope

NASA Astrophysics Data System (ADS)

Ogawara, Yasuo

2016-11-01

When I was a freshman at Tokyo University of Science, my senpai (upper-class student mentor) took me to a certain skiing ground in his car, which was equipped with standard tires. He tried to enter the parking area there, but his car could not climb a short slope leading to the entrance. I would like to describe here how he dealt with the problem and present a physical analysis.

Post-fire rill and gully formation, Schultz Fire 2010, Arizona, USA

Treesearch

Daniel G. Neary; Karen A. Koestner; Ann Youberg; Peter E. Koestner

2012-01-01

The Schultz Fire burned 6100 ha on the eastern slopes of the San Francisco Peaks in northern Arizona. The fire burned between June 20th and 30th, 2010, across moderate to very steep ponderosa pine and mixed conifer watersheds. About 40% of the fire area was classified as high-severity, mostly on mountain slopes greater than 30% and in places exceeding 100%. The upper...

First-year effects of rootraking on available nutrients in Piedmont Plateau soils

Treesearch

R.E. Banker; James H. Miller; D.E. Davis

1983-01-01

The effects of rootraking on the levels of Ca, Mg, K, PO4 and Na and on infiltration rates in Piedmont Plateau soils were investigated. Soil samples were taken before and after treatments at lo-foot intervals along permanent 100-foot lines located on the ridge, upper slope and lower slopes. Samples were taken at O-2, 2-4, 4-6, 6-12, 12-18...

Biophysical Factors Affecting the Distribution of Demersal Fish around the Head of a Submarine Canyon Off the Bonney Coast, South Australia

PubMed Central

Currie, David R.; McClatchie, Sam; Middleton, John F.; Nayar, Sasi

2012-01-01

We sampled the demersal fish community of the Bonney Canyon, South Australia at depths (100–1,500 m) and locations that are poorly known. Seventy-eight species of demersal fish were obtained from 12 depth-stratified trawls along, and to either side, of the central canyon axis. Distributional patterns in species richness and biomass were highly correlated. Three fish assemblage groupings, characterised by small suites of species with narrow depth distributions, were identified on the shelf, upper slope and mid slope. The assemblage groupings were largely explained by depth (ρw = 0.78). Compared to the depth gradient, canyon-related effects are weak or occur at spatial or temporal scales not sampled in this study. A conceptual physical model displayed features consistent with the depth zonational patterns in fish, and also indicated that canyon upwelling can occur. The depth zonation of the fish assemblage was associated with the depth distribution of water masses in the area. Notably, the mid-slope community (1,000 m) coincided with a layer of Antarctic Intermediate Water, the upper slope community (500 m) resided within the core of the Flinders Current, and the shelf community was located in a well-mixed layer of surface water (<450 m depth). PMID:22253907

Observations of vertical velocities in the tropical upper troposphere and lower stratosphere using the Arecibo 430-MHz radar

NASA Technical Reports Server (NTRS)

Cornish, C. R.

1988-01-01

The first clear-air observations of vertical velocities in the tropical upper troposphere and lower stratosphere (8-22 km) using the Arecibo 430-MHz radar are presented. Oscillations in the vertical velocity near the Brunt-Vaisala period are observed in the lower stratosphere during the 12-hour observation period. Frequency power spectra from the vertical velocity time series show a slope between -0.5 and -1.0. Vertical wave number spectra computed from the height profiles of vertical velocities have slopes between -1.0 and -1.5. These observed slopes do not agree well with the slopes of +1/3 and -2.5 for frequency and vertical wave number spectra, respectively, predicted by a universal gravity-wave spectrum model. The spectral power of wave number spectra of a radial beam directed 15 deg off-zenith is enhanced by an order of magnitude over the spectral power levels of the vertical beam. This enhancement suggests that other geophysical processes besides gravity waves are present in the horizontal flow. The steepening of the wave number spectrum of the off-vertical beam in the lower stratosphere to near -2.0 is attributed to a quasi-inertial period wave, which was present in the horizontal flow during the observation period.

Inorganic and organic geochemical fingerprinting of sediment sources and ocean circulation on a complex continental margin (São Paulo Bight, Brazil)

NASA Astrophysics Data System (ADS)

Michaelovitch de Mahiques, Michel; Jörg Hanebuth, Till Jens; Hanae Nagai, Renata; Caruso Bícego, Marcia; Lopes Figueira, Rubens Cesar; Mello Sousa, Silvia Helena; Burone, Leticia; Franco-Fraguas, Paula; Taniguchi, Satie; Barbosa Salaroli, Alexandre; Pereira Dias, Gilberto; Menezes Prates, Denise; Fernandes Freitas, Maria Eugenia

2017-03-01

In this study, we use inorganic (metal) and organic (bulk and molecular) markers in sediment samples of the south-eastern Brazilian margin to investigate the response of geochemical fingerprints to the complex hydrodynamic processes present in the area. Results indicate the potential of export of terrigenous siliciclastic and organic constituents to the upper slope, even in an area with limited fluvial supply.

Metal contents and especially the ln(Ti / Al) and ln(Fe / K) ratios make it possible to recognise the extension of shelf sediments toward the upper slope. Potassium, here expressed as ln(K / Sc) and ln(K / Al) ratios used as proxies of illite-kaolinite variations, proved to be an important parameter, especially because it allowed us to decipher the imprint of the northward flow of the Intermediate Western Boundary Current (IWBC) in comparison to the southward flows of the Brazil Current (BC) and Deep Western Boundary Current (DWBC). Using organic matter analyses, we were able to evaluate the extent of terrestrial contributions to the outer shelf and slope, even without the presence of significant fluvial input. In addition, molecular markers signify a slight increase in the input of C4-derived plants to the slope sediments, transported from distant areas by the main alongshore boundary currents, indicating that the terrestrial fraction of the organic matter deposited on the slope has a distinct origin when compared to shelf sediments.

Geochemical Identification of Windblown Dust Deposits in the Upper Permian Brushy Canyon Formation, Southern New Mexico

NASA Astrophysics Data System (ADS)

Tice, M. M.; Motanated, K.; Weiss, R.

2009-12-01

Windblown dust is a potentially important but difficult-to-quantify source of siliciclastics for sedimentary basins worldwide. Positively identifying windblown deposits requires distinguishing them from other low density suspension transport deposits. For instance, laminated very fine grained sandstones and siltstones of the Upper Permian Brushy Canyon Formation have been variously interpreted as 1) the deposits of slow-moving, low-density turbidity currents, 2) distal overbank deposits of turbidity currents, 3) the deposits of turbulent suspensions transported across a pycnocline (interflows), and 4) windblown dust. This facies forms the bulk of Brushy Canyon Formation slope deposits, so understanding its origin is critical to understanding the evolution of the basin as a whole. We use a geochemical mapping technique (x-ray fluorescence microscopy) to show that these rocks are up to two times enriched in very fine sand sized zircon and rutile grains relative to Bouma A divisions of interbedded turbidites, suggesting substantial turbulence during transport. However, in contrast with the A divisions, the laminated sandstones and siltstones never show evidence of scour or amalgamation, implying that flow turbulence did not interact with underlying beds. Moreover, proximal loess deposits are often characterized by elevated Zr/Al2O3. These observations are most consistent with windblown interpretations for Brushy Canyon Formation slope sediments, and suggest that evolution of this early deepwater slope system was controlled largely by short-distance aeolian transport of very fine sand and silt from the coast. Heavy mineral incorporation into Brushy Canyon Formation slope deposits as reflected in laminae-scale bulk Zr and Ti abundances may preserve a long-term record of local wind intensity during the Upper Permian.

Clay mineralogical record on the upper continental slope of the northwestern South China Sea since the Last Glacial Maximum

NASA Astrophysics Data System (ADS)

CHEN, Q.; Liu, Z.; Stattegger, K.

2012-12-01

Clay mineralogy of two gravity cores (18428 and 18429) on the upper continental slope of the northwestern South China Sea was investigated in order to understand terrigenous sediment sources and to evaluate the contribution from the Red River since the Late Glacial Maximum. Planktonic foraminiferal oxygen isotope and carbonate stratigraphies suggest that Core 18428 is constrained in Holocene while Core 18429 covers the period of MIS 1-2. Clay mineral assemblages of two cores are composed mainly of smectite (18-57%) and illite (21-41%), with minor chlorite (12-21%) and kaolinite (8-26%). In despite of relatively constant values of illite crystallinity, ranging among 0.14°-0.20° Δ2θ, the time series variation in clay mineral distributions indicates a strong glacial-interglacial shift. Contents of illite, chlorite, and kaolinite (Core 18429) in the Holocene are lower than in the glacial period, and vice versa for the smectite content. The provenance analysis based on clay mineralogy suggests the Red River as a predominant sedimentary source of illite, chlorite, and kaolinite during all the depositional period of MIS 1-2. The sea level change actually controlled the variations of clay mineral assemblages on the upper slope since the Last Glacial Maximum. When the sea level was low during the last glacial period, more terrigenous sediments from the Red River could reach the continental slope in the northwestern South China Sea. However, when the sea level is closed to the present situation during the Holocene, most of Red River sediments could be trapped in the Gulf of Tonkin, instead of draining in the deep South China Sea.

Rifting Process and Geomorphic Development of the Okinawa Tough, Southwest Japan

NASA Astrophysics Data System (ADS)

Sato, T.; Arai, K.; Inoue, T.; Matsumoto, D.

2012-12-01

The Ryukyu Island Arc extends from Kyushu to Taiwan, a distance of 1,200 km, along the Ryukyu Trench where the Philippine Sea Plate is subducting beneath the Eurasian Plate. The Okinawa Trough, a back arc basin has formed behind the Ryukyu Island Arc in late Pliocene to early Pleistocene. The research cruises of GH11 (from 14 July to 15 August, 2011) and GH12 (from 20 to 30 July, 2012) were carried out around the Okinawa Trough. More than 3,600 miles multi channel high-resolution seismic profiles were acquired during these cruises by the GI-gun (Generator 250 cu inch and Injector 105 cu. inch) systems with 16ch digital streamer cable. As a result, two unconformities and three depositional sequence divided by the unconformities are recognized in the trough. The lower and the midlle sequence are tilted and blocked by many normal faults, on the other hand the upper one is not tilted and shows the pattern of onlap fill. From this result, the upper sequence started to deposit after start of the rifting. Additionally, internal reflection of the upper sequence shows the cyclic activities of the rifting. The position of the rifting axis was revealed based on dip of the normal faults. As a result, rifting axis shows echelon arrangement and the displacement of the faults are varied with the segment of the arrangement. The location of the segment boundaries is correlated with geometrical boundary of the adjacent slope. Steep slope with incised valley is distributed in southwestern part where the displacement of the normal fault is large, on the other hand, gentle slope without incised valley is distributed in northeastern part where the displacement is small. This difference of the displacement strongly controls the geometry of the adjacent slope.

Mediterranean undercurrent sandy contourites, Gulf of Cadiz, Spain

USGS Publications Warehouse

Hans, Nelson C.; Baraza, J.; Maldonado, A.

1993-01-01

The Pliocene-Quaternary pattern of contourite deposits on the eastern Gulf of Cadiz continental slope results from an interaction between linear diapiric ridges that are perpendicular to slope contours and the Mediterranean undercurrent that has flowed northwestward parallel to the slope contours and down valleys between the ridges since the late Miocene opening of the Strait of Gibraltar. Coincident with the northwestward decrease in undercurrent speeds from the Strait there is the following northwestward gradation of sediment facies associations: (1) upper slope facies, (2) sand dune facies on the upstream mid-slope terrace, (3) large mud wave facies on the lower slope, (4) sediment drift facies banked against the diapiric ridges, and (5) valley facies between the ridges. The southeastern sediment drift facies closest to Gibraltar contains medium-fine sand beds interbedded with mud. The adjacent valley floor facies is composed of gravelly, shelly coarse to medium sand lags and large sand dunes on the valley margins. Compared to this, the northwestern drift contains coarse silt interbeds and the adjacent valley floors exhibit small to medium sand dunes of fine sand. Further northwestward, sediment drift grades to biogenous silt near the Faro Drift at the Portuguese border. Because of the complex pattern of contour-parallel and valley-perpendicular flow paths of the Mediterranean undercurrent, the larger-scale bedforms and coarser-grained sediment of valley facies trend perpendicular to the smaller-scale bedforms and finer-grained contourite deposits of adjacent sediment drift facies. The bottom-current deposits of valleys and the contourites of the Cadiz slope intervalley areas are distinct from turbidite systems. The valley sequences are not aggradational like turbidite channel-levee complexes, but typically exhibit bedrock walls against ridges, extensive scour and fill into adjacent contourites, transverse bedform fields and bioclastic lag deposits. Both valley and contourite deposits exhibit reverse graded bedding and sharp upper bed contacts in coarse-grained layers, low deposition rates, and a regional pattern of bedform zones, textural variation, and compositional gradation. The surface sandy contourite layer of 0.2-1.2 m thickness that covers the Gulf of Cadiz slope has formed during the present Holocene high sea level because high sea level results in maximum water depth over the Gibraltar sill and full development of the Mediterranean undercurrent. The late Pleistocene age of the mud underlying the surface sand sheet correlates with the age of the last sea-level lowstand and apparent weak Mediterranean undercurrent development. Thus, the cyclic deposition of sand or mud layers and contourite or drape sequences appear to be related to late Pliocene and Quaternary sea-level changes and Mediterranean water circulation patterns. Since its Pliocene origin, the contourite sequence has had low deposition rates of < 5 cm/1000y on the upper slope and < 13 cm/1000y in the middle slope sediment drift. ?? 1993.

Morphotectonics of the central Muertos thrust belt and Muertos Trough (northeastern Caribbean)

USGS Publications Warehouse

Granja, Bruna J.L.; ten Brink, Uri S.; Carbó-Gorosabel, Andrés; Muñoz-Martín, A.; Gomez, Ballesteros M.

2009-01-01

Multibeam bathymetry data acquired during the 2005 Spanish R/V Hesp??rides cruise and reprocessed multichannel seismic profiles provide the basis for the analysis of the morphology and deformation in the central Muertos Trough and Muertos thrust belt. The Muertos Trough is an elongated basin developed where the Venezuelan Basin crust is thrusted under the Muertos fold-and-thrust belt. Structural variations along the Muertos Trough are suggested to be a consequence of the overburden of the asymmetrical thrust belt and by the variable nature of the Venezuelan Basin crust along the margin. The insular slope can be divided into three east-west trending slope provinces with high lateral variability which correspond to different accretion stages: 1) The lower slope is composed of an active sequence of imbricate thrust slices and closed fold axes, which form short and narrow accretionary ridges and elongated slope basins; 2) The middle slope shows a less active imbricate structure resulting in lower superficial deformation and bigger slope basins; 3) The upper slope comprises the talus region and extended terraces burying an island arc basement and an inactive imbricate structure. The talus region is characterized by a dense drainage network that transports turbidite flows from the islands and their surrounding carbonate platform areas to the slope basins and sometimes to the trough. In the survey area the accommodation of the ongoing east-west differential motion between the Hispaniola and the Puerto Rico-Virgin Islands blocks takes place by means of diffuse deformation. The asymmetrical development of the thrust belt is not related to the geological conditions in the foreland, but rather may be caused by variations in the geometry and movement of the backstop. The map-view curves of the thrust belt and the symmetry of the recesses suggest a main north-south convergence along the Muertos margin. The western end of the Investigator Fault Zone comprises a broad band of active normal faults which result in high instability of the upper insular slope. ?? 2009 Elsevier B.V.

Controls on alluvial fan long-profiles

USGS Publications Warehouse

Stock, J.D.; Schmidt, K.M.; Miller, D.M.

2008-01-01

Water and debris flows exiting confined valleys have a tendency to deposit sediment on steep fans. On alluvial fans where water transport of gravel predominates, channel slopes tend to decrease downfan from ???0.10-0.04 to ???0.01 across wide ranges of climate and tectonism. Some have argued that this pattern reflects grain-size fining downfan such that higher threshold slopes are required just to entrain coarser particles in the waters of the upper fan, whereas lower slopes are required to entrain finer grains downfan (threshold hypothesis). An older hypothesis is that slope is adjusted to transport the supplied sediment load, which decreases downfan as deposition occurs (transport hypothesis). We have begun to test these hypotheses for alluvial fan long-profiles using detailed hydraulic and particle-size data in sediment transport models. On four alluvial fans in the western U.S., we find that channel hydraulic radiiare largely 0.5-0.9 m at fan heads, decreasing to 0.1-0.2 m at distal margins. We find that median gravel diameter does not change systematically along the upper 60%-80% of active fan channels as slope declines, so downstream gravel fining cannot explain most of the observed channel slope reduction. However, as slope declines, channel-bed sand cover increases systematically downfan from areal fractions of <20% above fan heads to distal fan values in excess of 70%. As a result, entrainment thresholds for bed material might decrease systematically downfan, leading to lower slopes. However, current models of this effect alone tend to underpredict downfan slope changes. This is likely due to off-channel gravel deposition. Calculations that match observed fan long-profiles require an exponential decline in gravel transport rate, so that on some fans approximately half of the load must be deposited off channel every -0.20-1.4 km downfan. This leads us to hypothesize that some alluvial fan long-proffies are statements about the rate of overbank deposition of coarse particles downfan, a process for which there is currently no mechanistic theory. ?? 2007 Geological Society of America.

Comparative organic geochemistry of Indian margin (Arabian Sea) sediments: estuary to continental slope

NASA Astrophysics Data System (ADS)

Cowie, G.; Mowbray, S.; Kurian, S.; Sarkar, A.; White, C.; Anderson, A.; Vergnaud, B.; Johnstone, G.; Brear, S.; Woulds, C.; Naqvi, S. W.; Kitazato, H.

2014-02-01

Surface sediments from sites across the Indian margin of the Arabian Sea were analysed for their carbon and nitrogen compositions (elemental and stable isotopic), grain size distributions and biochemical indices of organic matter (OM) source and/or degradation state. Site locations ranged from the estuaries of the Mandovi and Zuari rivers to depths of ~ 2000 m on the continental slope, thus spanning nearshore muds and sands on the shelf and both the semi-permanent oxygen minimum zone (OMZ) on the upper slope (~ 200-1300 m) and the seasonal hypoxic zone that impinges on the shelf. Source indices showed mixed marine and terrigenous OM within the estuaries, and overwhelming predominance (80%+) of marine OM on the shelf and slope. Thus, riverine OM is heavily diluted by autochthonous marine OM and/or is efficiently remineralised within or immediately offshore of the estuaries. Any terrigenous OM that is exported appears to be retained in nearshore muds; lignin phenols indicate that the small terrigenous OM content of slope sediments is of different origin, potentially from rivers to the north. Organic C contents of surface shelf and slope sediments varied from < 0.5 wt % in relict shelf sands to over 7 wt % at slope sites within the OMZ, decreasing to ≤ 1 wt % at 2000 m. Major variability (~ 5 wt %) was found at slope sites within the OMZ of similar depth and near-identical bottom-water oxygen concentration. A strong relationship between organic C and sediment grain size was seen for sediments within the OMZ, but lower C loadings were found for sites on the shelf and below the OMZ. Diagenetic indices confirmed that lower C content below the OMZ is associated with greater extent of OM degradation, but that C-poor shelf sediments are not consistently more degraded than those within the OMZ. Together, the results indicate that OM enrichment on the upper slope can be explained by physical controls (winnowing and/or dilution) on the shelf and progressive OM degradation with increasing oxygen exposure below the OMZ. Reduced oxygen exposure may contribute to OM enrichment at some sites within the OMZ, but hydrodynamic processes are the overriding control on sediment OM distribution.

The Problem of Alluvial Fan Slopes

NASA Astrophysics Data System (ADS)

Stock, J. D.; Schmidt, K.

2005-12-01

Water and debris flows exiting confined valleys have a tendency to deposit sediment on steep fans. On alluvial fans, where water transport predominates, channel slopes tend to decrease downfan from ~0.08 to ~0.01 across wide ranges of climate and tectonism. Some have argued that this pattern reflects downfan grainsize fining so that higher slopes are required just to entrain coarser particles in the waters of the upper fan, while entrainment of finer grains downfan requires lower slopes (threshold hypothesis). An older hypothesis is that slope is adjusted to transport the supplied sediment load, which decreases downfan as deposition occurs (transport hypothesis). We have begun to test these hypotheses using detailed field measurements of hydraulic and sediment variables in sediment transport models. On some fans in the western U.S. we find that alluvial fan channel bankfull depths are largely 0.5-1.5 m at fan heads, decreasing to 0.1-0.2 m at distal margins. Contrary to many previous studies, we find that median gravel diameter does not change systematically along the upper 60- 80% of active fan channels. So downstream gravel fining cannot explain most of the observed channel slope reduction. However, as slope declines, surface sand cover increases systematically downfan from values of <20% above fan heads to distal fan values in excess of 70%. As a result, the threshold for sediment motion might decrease systematically downfan, leading to lower slopes. However, current models of this effect alone tend to underpredict downfan slope changes. This is likely due to off- channel gravel deposition. Calculations that match observed fan long-profiles require an exponential decline in gravel transport rate, so that on some fans approximately half of the load must be deposited off-channel every ~0.25-1.25 km downfan. This leads us to hypothesize that alluvial fan long- profiles are largely statements about the rate of deposition downfan. If so, there may be climatic and tectonic information in the long-profile, but a mechanistic theory for downfan deposition rate will be needed.

Widespread methane leakage from the sea floor on the northern US Atlantic margin

USGS Publications Warehouse

Skarke, Adam; Ruppel, Carolyn; Kodis, Mali'o; Brothers, Daniel S.; Lobecker, Elizabeth A.

2014-01-01

Methane emissions from the sea floor affect methane inputs into the atmosphere, ocean acidification and de-oxygenation, the distribution of chemosynthetic communities and energy resources. Global methane flux from seabed cold seeps has only been estimated for continental shelves, at 8 to 65 Tg CH4 yr−1, yet other parts of marine continental margins are also emitting methane. The US Atlantic margin has not been considered an area of widespread seepage, with only three methane seeps recognized seaward of the shelf break. However, massive upper-slope seepage related to gas hydrate degradation has been predicted for the southern part of this margin, even though this process has previously only been recognized in the Arctic. Here we use multibeam water-column backscatter data that cover 94,000 km2 of sea floor to identify about 570 gas plumes at water depths between 50 and 1,700 m between Cape Hatteras and Georges Bank on the northern US Atlantic passive margin. About 440 seeps originate at water depths that bracket the updip limit for methane hydrate stability. Contemporary upper-slope seepage there may be triggered by ongoing warming of intermediate waters, but authigenic carbonates observed imply that emissions have continued for more than 1,000 years at some seeps. Extrapolating the upper-slope seep density on this margin to the global passive margin system, we suggest that tens of thousands of seeps could be discoverable.

Upper bound on the slope of steady water waves with small adverse vorticity

NASA Astrophysics Data System (ADS)

So, Seung Wook; Strauss, Walter A.

2018-03-01

We consider the angle of inclination (with respect to the horizontal) of the profile of a steady 2D inviscid symmetric periodic or solitary water wave subject to gravity. There is an upper bound of 31.15° in the irrotational case [1] and an upper bound of 45° in the case of favorable vorticity [13]. On the other hand, if the vorticity is adverse, the profile can become vertical. We prove here that if the adverse vorticity is sufficiently small, then the angle still has an upper bound which is slightly larger than 45°.

Context view showing Hoist House at center, upper end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Context view showing Hoist House at center, upper end of inclined railroad in left foreground, part of valve house left of center and part of surge chamber in left background. View to southwest - Mystic Lake Hydroelectric Facility, Hoist House, On west slope of West Rosebud Creek, 1 3/4 miles northeast of Mystic Lake Dam, Fishtail, Stillwater County, MT

Sedimentary conditions of Upper Permian volcano-clastic rocks of Ayan-Yrahskiy anticlinorium (Verhoyansk-Kolyma orogen)

NASA Astrophysics Data System (ADS)

Astakhova, Anna; Khardikov, Aleksandr

2013-04-01

Sedimentation conditions of upper Permian volcano-clastic rocks of Ayan-Yurakhsky anticlinorium are the reason of discussions between researchers. It is important to correctly solve this problem. Investigation allows us to conclude that upper Permian sediments was formed due to high rate deltaic sedimentation on shelf and continental slope of epicontinental sea basin. More than 45 outcrops of upper Permian sediments were described within Ayan-Yurakhsky anticlinorium. Termochemical and X-ray phase, lithological facies, stadial, paleogeographic and others were applied. Investigation allows to classify following types: tuffs, tuffites of andesites, andesi-dacites, sandstone tuffs, siltstone tuffs and claystone tuffs. Two facies were deliniated in the research area: 1) delta channel facies 2) epicontinental sea shelf edge and continental slope. Delta channel facies are located on the south-west part of Aian-Yrahskiy anticlinorium. It is composed of silty packsand and psammitic tuff-siltstone alternation and gravel-psammitic andesi-dacitic tuffute and tuff-breccia bands. Sediments have cross-bedding, through cross-bedding, curvilinear lamination structures. Facies occurred during high rate deltaic sedimentation on the shelf of epicontinental sea. Epicontinental sea shelf edge and continental slope facies are located on the south-west part. Sediments are represented by large thickness tuff-siltstone with tuff-sandstone, tuff-madstone, tuff, tuffite bands and lenses. Large number of submarine landslides sediments provide evidence that there was high angle sea floore environment. 30-50 m diametr eruption centers were described by authors during geological traverses. They are located in Kulu river basin. Their locations are limited by deep-seated pre-ore fault which extended along Ayan-Yurakhsky anticlinorium. U-Pb SHRIMP method showed that the average age of circons, taken from eruption centers, is Permian (256,3±3,7 ma). This fact confirms our emphasis that eruption centers were the centre of underwater effusive explosions which had been occurred in late Permian time. Gold ore deposits mainly localized in the south of Ayan-Yurakhsky anticlinorium and associated with upper Permian deltaic facies sediments. Taking into account lithological facies feature and volcanoclastic origin of sediments it is reasonable to suggest expelled-catagenesis model of gold mineralization. Gold was entered in sedimentary basin with piroclastic material. During catagenesis stage gold migrated from complex of shelf edge and continental slope to fan delta front complex in conjunction with expelled water. The emplacement of ore gold deposits related with upper Permian sediments can be successfully predicted, using this model and associated techniques.

[Effects of sub-watershed landscape patterns at the upper reaches of Minjiang River on soil erosion].

PubMed

Yang, Meng; Li, Xiu-zhen; Yang, Zhao-ping; Hu, Yuan-man; Wen, Qing-chun

2007-11-01

Based on GIS, the spatial distribution of soil loss and sediment yield in Heishui and Zhenjiangguan sub-watersheds at the upper reaches of Minjiang River was simulated by using sediment delivery-distribution (SEDD) model, and the effects of land use/cover types on soil erosion and sediment yield were discussed, based on the simulated results and related land use maps. A landscape index named location-weighted landscape contrast index (LCI) was calculated to evaluate the effects of landscape components' spatial distribution, weight, and structure of land use/cover on soil erosion. The results showed the soil erosion modulus varied with land use pattern, and decreased in the order of bare rock > urban/village > rangeland > farmland > shrub > forest. There were no significant differences in sediment yield modules among different land use/covers. In the two sub-watersheds, the spatial distribution of land use/covers on slope tended to decrease the final sediment load at watershed outlet, hut as related to relative elevation, relative distance, and flow length, the spatial distribution tended to increase sediment yield. The two sub-watersheds had different advantages as related to landscape components' spatial distribution, but, when the land use/cover weight was considered, the advantages of Zhenjiangguan sub-watershed increased. If the land use/cover structure was considered in addition, the landscape pattern of Zhenjiangguan subwatershed was better. Therefore, only the three elements, i.e., landscape components' spatial distribution, land use/cover weight, and land use/cover structure, were considered comprehensively, can we get an overall evaluation on the effects of landscape pattern on soil erosion. The calculation of LCI related to slope suggested that this index couldn' t accurately reflect the effects of land use/cover weight and structure on soil erosion, and thus, needed to be modified.

Biostratigraphic sequence analysis of two Lower Miocene to Pliocene sections, Eastern Falcon, Northwestern Venezuela

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz De Gamero, M.L.; Giffuni, G.; Castro Mora, M.

1993-02-01

The eastern region of the Falcon Basin in northwestern Venezuela comprises a thick sedimentary sequence deposited from a deep marine bathyal to neritic environment, ranging in age from the Middle Eocene to the Pliocene. A detailed biostratigraphic study (foraminifera and calcareous nannoplankton) was carried out in two sedimentary sequences outcropping in Cumarebo and Piritu, adjacent areas of eastern Falcon, representing: platform, slope and basinal settings. The Cumarebo section is continuous in the studied interval, from the Middle Miocene to the Pliocene. The Piritu section is continuous from the Lower to the lower Upper Miocene, terminating unconformably beneath a thin intervalmore » of middle Pliocene platform sediments, indicating tectonism during the latest Miocene. The sequence stratigraphical interpretation was based on the biostratigraphic analysis of the benthic and planktonic fossils, facies distribution and sedimentological data. Systems tracts, sequence boundaries and maximum flooding surfaces from cycles TB2.4 to TB3.5 of the cycle chart were identified. In the Cumarebo section, the upper Middle and Upper Miocene is mostly composed of shales, with some turbiditic sands belonging to a LSW system tract. The upper most Miocene contains a thick carbonate buildup (HST), and it is overlain by a Pliocene section that shallows upward from upper slope to outer shelf depositional environments. In the basinal (Piritu) section, most of the sediments are deep-water shales belonging to a LSW system tract, with some turbiditic sands in the upper Lower Miocene. TST and HST sediments, with scattered carbonate buildups in the upper Middle Miocene were also identified.« less

Slope Stability of Geosynthetic Clay Liner Test Plots

EPA Science Inventory

Fourteen full-scale field test plots containing five types of geosynthetic clay liners (GCLs) were constructed on 2H:IV and 3H:IV slopes for the purpose of assessing slope stability. The test plots were designed to simulate typical final cover systems for landfill. Slides occurr...

High-resolution vertical velocities and their power spectrum observed with the MAARSY radar - Part 1: frequency spectrum

NASA Astrophysics Data System (ADS)

Li, Qiang; Rapp, Markus; Stober, Gunter; Latteck, Ralph

2018-04-01

The Middle Atmosphere Alomar Radar System (MAARSY) installed at the island of Andøya has been run for continuous probing of atmospheric winds in the upper troposphere and lower stratosphere (UTLS) region. In the current study, we present high-resolution wind measurements during the period between 2010 and 2013 with MAARSY. The spectral analysis applying the Lomb-Scargle periodogram method has been carried out to determine the frequency spectra of vertical wind velocity. From a total of 522 days of observations, the statistics of the spectral slope have been derived and show a dependence on the background wind conditions. It is a general feature that the observed spectra of vertical velocity during active periods (with wind velocity > 10 m s-1) are much steeper than during quiet periods (with wind velocity < 10 m s-1). The distribution of spectral slopes is roughly symmetric with a maximum at -5/3 during active periods, whereas a very asymmetric distribution with a maximum at around -1 is observed during quiet periods. The slope profiles along altitudes reveal a significant height dependence for both conditions, i.e., the spectra become shallower with increasing altitudes in the upper troposphere and maintain roughly a constant slope in the lower stratosphere. With both wind conditions considered together the general spectra are obtained and their slopes are compared with the background horizontal winds. The comparisons show that the observed spectra become steeper with increasing wind velocities under quiet conditions, approach a spectral slope of -5/3 at a wind velocity of 10 m s-1 and then roughly maintain this slope (-5/3) for even stronger winds. Our findings show an overall agreement with previous studies; furthermore, they provide a more complete climatology of frequency spectra of vertical wind velocities under different wind conditions.

Marine geology of the Forearc region, southern Mariana Island arc

NASA Astrophysics Data System (ADS)

Karig, D. E.; Ranken, Beverly

The Mariana Arc serves as a type example of an oceanic arc system because of its long history without a continental influence and because of the large suite of data collected from that area. The concentration of deep-sea drilling and related survey data near 18°N has been interpreted in support of subsidence and narrowing of the forearc with time as a result of tectonic erosion. On the contrary, interpretation of a lesser concentration of data from the south end of the arc presented here suggests growth and relative uplift of the lower trench slope. Truncation of all forearc elements occurs south of 13°N, probably as a result of strike slip faulting along east-west fractures that define a transform between the back arc spreading ridge and the trench. North of 13°30'N the inner trench slope is ribbed with ridges that trend parallel to or convex toward the trench. These ridges are largest and perhaps most structurally active at the base of the trench slope. Depositional depth of sediments in Deep Sea Drilling Project holes drilled in the upper slope apron, concave upward slopes of this apron, which trap turbidites, and internal arcward fanning of deeper apron strata are cited in support of relative uplift and arcward rotation of the seaward part of the inner slope and of minor absolute uplift of the sediment apron. This pattern of vertical displacement and rotation, coupled with progressive downlap rather than truncation of apron strata, argues against tectonic erosion and subsidence. The conflicting data may be a result of changing response of the arc over time. Forearc volcanism and tectonic disruption of the basement beneath the upper slope apparently ceased by the early Oligocene. Younger features are more compatible with intermittent accretion of oceanic material, possibly tectonically mixed into the arc basement.

Character, paleoenvironment, rate of accumulation, and evidence for seismic triggering of Holocene turbidites, Canada Abyssal Plain, Arctic Ocean

USGS Publications Warehouse

Grantz, A.; Phillips, R.L.; Mullen, M.W.; Starratt, S.W.; Jones, Glenn A.; Naidu, A.S.; Finney, B.P.

1996-01-01

Four box cores and one piston core show that Holocene sedimentation on the southern Canada Abyssal Plain for the last 8010??120 yr has consisted of a continuing rain of pelagic organic and ice-rafted elastic sediment with a net accumulation rate during the late Holocene of ???10 mm/1000 yr, and episodically emplaced turbidites 1-5 m thick deposited at intervals of 830 to 3450 yr (average 2000 yr). The average net accumulation rate of the mixed sequence of turbidites and thin pelagite interbeds in the cores is about 1.2 m/1000 yr. Physiography suggests that the turbidites originated on the Mackenzie Delta or its clinoform, and ??13C values of -27 to - 25??? in the turbidites are compatible with a provenance on a delta. Extant displaced neritic and lower slope to basin plain calcareous benthic foraminifers coexist in the turbidite units. Their joint occurence indicates that the turbidites originated on the modern continental shelf and entrained sediment from the slope and rise enroute to their final resting place on the Canada Abyssal Plain. The presence of Middle Pleistocene diatoms in the turbidites suggests, in addition, that the turbidites may have originated in shallow submarine slides beneath the upper slope or outer shelf. Small but consistent differences in organic carbon content and ??13C values between the turbidite units suggest that they did not share an identical provenance, which is at least compatible with an origin in slope failures. The primary provenance of the ice-rafted component of the pelagic beds was the glaciated terrane of northwestern Canada; and the provenance of the turbidite units was Pleistocene and Holocene sedimentary deposits on the outer continental shelf and upper slope of the Mackenzie Delta. Largely local derivation of the sediment of the Canada Abyssal Plain indicates that sediment accumulation rates in the Arctic Ocean are valid only for regions with similar depositional sources and processes, and that these rates cannot be extrapolated regionally. The location of an elliptical zone of active seismicity over the inferred provenance of the turbidites suggests that they were triggered by large earthquakes. Distal turbidite sediment accumulation rates were more than two orders of magnitude greater than pelagic sediment accumulation rates on the Canada Abyssal Plain during the last 8000 years. This disparity reconciles the discrepancy between the high accumulation rates assumed by some for the Arctic Ocean because of the numerous major rivers and large ice sheets that discharge into this small mediterranean basin and the low pelagic sedimentation rates that have been reported from the Arctic Ocean.

Long-Term Observations of Epibenthic Fish Zonation in the Deep Northern Gulf of Mexico

PubMed Central

Wei, Chih-Lin; Rowe, Gilbert T.; Haedrich, Richard L.; Boland, Gregory S.

2012-01-01

A total of 172 bottom trawl/skimmer samples (183 to 3655-m depth) from three deep-sea studies, R/V Alaminos cruises (1964–1973), Northern Gulf of Mexico Continental Slope (NGoMCS) study (1983–1985) and Deep Gulf of Mexico Benthos (DGoMB) program (2000 to 2002), were compiled to examine temporal and large-scale changes in epibenthic fish species composition. Based on percent species shared among samples, faunal groups (≥10% species shared) consistently reoccurred over time on the shelf-break (ca. 200 m), upper-slope (ca. 300 to 500 m) and upper-to-mid slope (ca. 500 to 1500 m) depths. These similar depth groups also merged when the three studies were pooled together, suggesting that there has been no large-scale temporal change in depth zonation on the upper section of the continental margin. Permutational multivariate analysis of variance (PERMANOVA) also detected no significant species changes on the limited sites and areas that have been revisited across the studies (P>0.05). Based on the ordination of the species shared among samples, species replacement was a continuum along a depth or macrobenthos biomass gradient. Despite the well-known, close, negative relationship between water depth and macrofaunal biomass, the fish species changed more rapidly at depth shallower than 1,000 m, but the rate of change was surprisingly slow at the highest macrofaunal biomass (>100 mg C m−2), suggesting that the composition of epibenthic fishes was not altered in response to the extremely high macrofaunal biomass in the upper Mississippi and De Soto Submarine Canyons. An alternative is that the pattern of fish species turnover is related to the decline in macrofaunal biomass, the presumptive prey of the fish, along the depth gradient. PMID:23056412

Long-term observations of epibenthic fish zonation in the deep northern Gulf of Mexico.

PubMed

Wei, Chih-Lin; Rowe, Gilbert T; Haedrich, Richard L; Boland, Gregory S

2012-01-01

A total of 172 bottom trawl/skimmer samples (183 to 3655-m depth) from three deep-sea studies, R/V Alaminos cruises (1964-1973), Northern Gulf of Mexico Continental Slope (NGoMCS) study (1983-1985) and Deep Gulf of Mexico Benthos (DGoMB) program (2000 to 2002), were compiled to examine temporal and large-scale changes in epibenthic fish species composition. Based on percent species shared among samples, faunal groups (≥10% species shared) consistently reoccurred over time on the shelf-break (ca. 200 m), upper-slope (ca. 300 to 500 m) and upper-to-mid slope (ca. 500 to 1500 m) depths. These similar depth groups also merged when the three studies were pooled together, suggesting that there has been no large-scale temporal change in depth zonation on the upper section of the continental margin. Permutational multivariate analysis of variance (PERMANOVA) also detected no significant species changes on the limited sites and areas that have been revisited across the studies (P>0.05). Based on the ordination of the species shared among samples, species replacement was a continuum along a depth or macrobenthos biomass gradient. Despite the well-known, close, negative relationship between water depth and macrofaunal biomass, the fish species changed more rapidly at depth shallower than 1,000 m, but the rate of change was surprisingly slow at the highest macrofaunal biomass (>100 mg C m(-2)), suggesting that the composition of epibenthic fishes was not altered in response to the extremely high macrofaunal biomass in the upper Mississippi and De Soto Submarine Canyons. An alternative is that the pattern of fish species turnover is related to the decline in macrofaunal biomass, the presumptive prey of the fish, along the depth gradient.

Experimentally reducing clutch size reveals a fixed upper limit to egg size in snakes, evidence from the king ratsnake, Elaphe carinata.

PubMed

Ji, Xiang; Du, Wei-Guo; Li, Hong; Lin, Long-Hui

2006-08-01

Snakes are free of the pelvic girdle's constraint on maximum offspring size, and therefore present an opportunity to investigate the upper limit to offspring size without the limit imposed by the pelvic girdle dimension. We used the king ratsnake (Elaphe carinata) as a model animal to examine whether follicle ablation may result in enlargement of egg size in snakes and, if so, whether there is a fixed upper limit to egg size. Females with small sized yolking follicles were assigned to three manipulated, one sham-manipulated and one control treatments in mid-May, and two, four or six yolking follicles in the manipulated females were then ablated. Females undergoing follicle ablation produced fewer, but larger as well as more elongated, eggs than control females primarily by increasing egg length. This finding suggests that follicle ablation may result in enlargement of egg size in E. carinata. Mean values for egg width remained almost unchanged across the five treatments, suggesting that egg width is more likely to be shaped by the morphological feature of the oviduct. Clutch mass dropped dramatically in four- and six-follicle ablated females. The function describing the relationship between size and number of eggs reveals that egg size increases with decreasing clutch size at an ever-decreasing rate, with the tangent slope of the function for the six-follicle ablation treatment being -0.04. According to the function describing instantaneous variation in tangent slope, the maximum value of tangent slope should converge towards zero. This result provides evidence that there is a fixed upper limit to egg size in E. carinata.

Debris flows as geomorphic agents in the Huachuca Mountains of southeastern Arizona

USGS Publications Warehouse

Wohl, E.E.; Pearthree, P.P.

1991-01-01

Numerous debris flows occurred in the Huachuca Mountains of southeastern Arizona during the summer rainy season of 1988 in areas that were burned by a forest fire earlier in the summer. Debris flows occurred following a major forest fire in 1977 as well, suggesting a causal link between fires and debris flows. Abundant evidence of older debris flows preserved along channels and in mountain front fans indicates that debris flows have occurred repeteadly during the late Quaternary in this environment. Soil development in sequences of debris-flow deposits indicates that debris flows probably recur over time intervals of several hundred to a thousand years in individual drainage basins in the study area. Surface runoff in the steep drainage basins of the Huachuca Mountains is greatly enhanced following forest fires, as the hillslopes are denuded of their vegetative cover. Water and sediment eroded from the hillslope regolith are rapidly introduced into the upper reaches of tributary channels by widespread rilling and slope wash during rainfall events. This influx of water and sediment destabilizes regolith previously accumulated in the channel, triggering debris flows that scour the channel to bedrock in the upper reaches. Following a debris flow, the scoured, trapezoidally-shaped channel gradually assumes a swale shape and the percentage of exposed bedrock declines, as material is introduced from the slopes. Debris flows do a tremendous amount of work in a very short time, however, and are the major channel-forming events. Where the tributary channels enter larger, trunk channels, the debris flows serve as the main source of very coarse sediment. The local slope and coarse particle distribution of the trunk channel depend on the competence of water flows in the channel to transport the material introduced by debris flows. Where the smaller channels drain directly to the mountain front, debris flows create extensive alluvial fans which dominate the morphology of the basin-range boundary. Time intervals between debris flows in the drainage basins of the Huachuca Mountains are probably controlled by complex interactions among climate, forest fires and slope processes. Fires destroy the protective vegetation that stabilizes the upper catchment slopes and inhibits erosion. However, not every fire that burns a catchment causes debris flows, because sufficient weathered material must accumulate in the upper channel reaches to initiate a large debris flow. If such accumulation has not occurred, the material introduced to a channel following a forest fire will move only a short distance down the channel. Thus, the episodic nature of debris flows probably depends on rates of slope weathering and erosion, which are in turn controlled by climate, both directly and through vegetation and forest fires. ?? 1991.

Lithology rules badland distribution and typology in a montane Mediterranean environment (upper Llobregat basin, Catalan Pre-Pyrenees)

NASA Astrophysics Data System (ADS)

Moreno de las Heras, Mariano; Gallart, Francesc

2016-04-01

Badlands (i.e. highly dissected areas carved in soft bedrock with little or no vegetation) are pervasive in a wide range of environmental conditions across the Mediterranean region, including semiarid, sub-humid and humid environments, and represent hotspots of erosion and sediment production at the regional scale. On montane (cold sub-humid and humid) Mediterranean landscapes, harsh thermal conditions on north-facing slopes favors intense bedrock weathering and impose serious constraints for plant colonization, which has generally been argued to explain preferential distribution of badlands on shady aspects. We study the distribution and typology of badlands in the upper Llobregat basin (500 km2, 700-2400 m.a.s.l. elevation, 700-900 mm annual rainfall, 8-11°C mean temp.). We mapped regional badlands by manually digitizing affected areas on recent (2012) high resolution (50 cm pixel) ortophotos. Badlands extend over about 200 ha in the upper Llobregat basin and are developed on Paleocene continental lutites (Garumnian Facies, Tremp Formation) and Eocene marine marls (Sagnari, Armancies and Vallfogona Formations). While badlands on Eocene marls showed a preferential distribution on north-facing shady slopes, badland occurrence on the highly unstable smectite-rich Garumnian lutites did not reveal clear aspect trends. In addition, elevation, which broadly controls winter temperatures in the region, did not show a clear influence on badland distribution. A principal component analysis was applied to study badland type using general geomorphological and vegetation metrics (i.e. badland size, slope, aspect, elevation gradient, connection to the regional drainage network, vegetation greenness) derived from a high resolution digital elevation model (5 m pixel) and pan-sharpened Landsat 8 MSAVI imagery (15 m pixel). Lithology was found to largely impact badland type, with Garumnian lutite badlands showing lower slope gradients (20°-30° average slope) than badlands on Eocene marls (30°-40° avg. slope). Badland size affected the extent to which badlands are hydrologically arranged in the basin (i.e. the larger the size and elevation gradient of the badland, the better connected was to the regional drainage network), while aspect regulated vegetation development (i.e. north-exposed badlands showed lower levels of vegetation greenness than south-exposed badlands). Overall our results reveal lithology as the main factor that broadly rule badland distribution and diversity under the montane Mediterranean conditions of the upper Llobregat basin, improving former results obtained in the area. This work is funded by a Beatriu de Pinós fellowship co-funded by the European Commission and the Generalitat de Catalunya (SEDCONMED, ref. 2014 BP-B 00111).

Weight compensation characteristics of Armeo®Spring exoskeleton: implications for clinical practice and research.

PubMed

Perry, Bonnie E; Evans, Emily K; Stokic, Dobrivoje S

2017-02-17

Armeo®Spring exoskeleton is widely used for upper extremity rehabilitation; however, weight compensation provided by the device appears insufficiently characterized to fully utilize it in clinical and research settings. Weight compensation was quantified by measuring static force in the sagittal plane with a load cell attached to the elbow joint of Armeo®Spring. All upper spring settings were examined in 5° increments at the minimum, maximum, and two intermediate upper and lower module length settings, while keeping the lower spring at minimum. The same measurements were made for minimum upper spring setting and maximum lower spring setting at minimum and maximum module lengths. Weight compensation was plotted against upper module angles, and slope was analyzed for each condition. The Armeo®Spring design prompted defining the slack angle and exoskeleton balance angle, which, depending on spring and length settings, divide the operating range into different unloading and loading regions. Higher spring tensions and shorter module lengths provided greater unloading (≤6.32 kg of support). Weight compensation slope decreased faster with shorter length settings (minimum length = -0.082 ± 0.002 kg/°; maximum length = -0.046 ± 0.001 kg/°) independent of spring settings. Understanding the impact of different settings on the Armeo®Spring weight compensation should help define best clinical practice and improve fidelity of research.

Submarine groundwater discharge and solute transport under a transgressive barrier island

NASA Astrophysics Data System (ADS)

Evans, Tyler B.; Wilson, Alicia M.

2017-04-01

Many recent investigations of groundwater dynamics in beaches employed groundwater models that assumed isotropic, numerically-convenient hydrogeological conditions. Real beaches exhibit local variability with respect to stratigraphy, sediment grain size and associated topographic profile, so that groundwater flow may diverge significantly from idealized models. We used a combination of hydrogeologic field methods and a variable-density, saturated-unsaturated, transient groundwater flow model to investigate SGD and solute transport under Cabretta Beach, a small transgressive barrier island seaward of Sapelo Island, Georgia. We found that the inclusion of real beach heterogeneity drove important deviations from predictions based on theoretical beaches. Cabretta Beach sustained a stronger upper saline plume than predicted due to the presence of a buried silty mud layer beneath the surface. Infiltration of seawater was greater for neap tides than for spring tides due to variations in beach slope. The strength of the upper saline plume was greatest during spring tides, contrary to recent model predictions. The position and width of the upper saline plume was highly dynamic through the lunar cycle. Our results suggest that field measurements of salinity gradients may be useful for estimating rates of tidally and density driven recirculation through the beach. Finally, our results indicate that several important biogeochemical cycles recently studied at Cabretta Beach were heavily influenced by groundwater flow and associated solute transport.

Biodiversity of macrofaunal assemblages from three Portuguese submarine canyons (NE Atlantic)

NASA Astrophysics Data System (ADS)

Cunha, Marina R.; Paterson, Gordon L. J.; Amaro, Teresa; Blackbird, Sabena; de Stigter, Henko C.; Ferreira, Clarisse; Glover, Adrian; Hilário, Ana; Kiriakoulakis, Konstadinos; Neal, Lenka; Ravara, Ascensão; Rodrigues, Clara F.; Tiago, Áurea; Billett, David S. M.

2011-12-01

The macrofaunal assemblages from three Portuguese submarine canyons, Nazaré, Cascais and Setúbal were studied from samples collected at their upper (900-1000 m), middle (3200-3500 m) and lower sections (4200-4500 m) and at the adjacent open slopes (˜1000 m), during the HERMES cruises D297 (R.R.S. Discovery, 2005) CD179 (R.R.S. Charles Darwin, 2006) and 64PE252 (R.V. Pelagia, 2006). The taxonomic composition and patterns in biodiversity, abundance and community structure of the benthic macrofauna were described. Annelida (42.1% of total abundance; 137 species) and Arthropoda (20.6%; 162 species) were, respectively, the most abundant and the most species-rich Phyla among the 342 taxa identified during this study. Multivariate analyses showed significant differences between and within canyons and between canyons and open slope assemblages. At their upper section, canyons supported higher macrofauna abundance but slightly lower biodiversity than the adjacent slopes at similar depth. In all canyons abundance reached the highest value in the middle section and the lowest in the upper section, with marked fluctuations in Nazaré (474-4599 ind. m -2) and lower variability in Cascais (583-1125 ind. m -2). The high abundance and dominance of the assemblages in the middle section of Nazaré and Setúbal was accompanied by depressed biodiversity, while in Cascais, Hurlbert's expected species richness showed increasing values from the upper to the middle canyon, and maintained the high values at the lower section. Overall, the Nazaré Canyon showed the lowest expected species richness (ES (100): 16-39) and the Cascais Canyon the highest (39-54). There was a significant negative Kendall's correlation between total organic carbon concentrations in the superficial sediments and ES (100) and a significant positive correlation between total nitrogen and macrofauna density. The influences of organic enrichment, sediment heterogeneity and hydrodynamic regime on the abundance, diversity and community structure of the macrofauna are discussed. It is suggested that altered and localised environmental conditions in the Portuguese canyons play an important role in modifying more common abundance and diversity bathymetric patterns evident in many continental slope environments.

Comparison of rumination activity measured using rumination collars against direct visual observations and analysis of video recordings of dairy cows in commercial farm environments.

PubMed

Ambriz-Vilchis, V; Jessop, N S; Fawcett, R H; Shaw, D J; Macrae, A I

2015-03-01

Automated systems for monitoring the behavior of cows have become increasingly important for management routines and for monitoring health and welfare. In the past few decades, various devices that record rumination have been developed. The aim of the present study was to compare rumination activity measured with a commercially available rumination collar (RC) against that obtained by direct visual observations and analysis of video recordings in commercial dairy cows. Rumination time from video recordings was recorded by a trained observer. To assess observer reliability, data were recorded twice, and the duration of recorded behaviors was very similar and highly correlated between these 2 measurements (mean=39±4 and 38±4 min/2 h). Measurements of rumination time obtained with RC when compared with analysis of video recordings and direct observations were variable: RC output was significantly positively related to observed rumination activity when dealing with animals housed indoors (trial 1 video recordings: slope=1.02, 95% CI=0.92-1.12), and the limits of agreement method (LoA) showed differences (in min per 2-h block) to be within -26.92 lower and 24.27 upper limits. Trial 1 direct observations: slope=1.08, 95% CI=0.62-1.55, and the LoA showed differences to be within -28.54 lower and 21.98 upper limits. Trial 2: slope=0.93, 95% CI=0.64-1.23, and the LoA showed differences to be within -32.56 lower and 19.84 upper limits. However, the results were poor when cows were outside grazing grass (trial 3: slope=0.57, 95% CI=0.13-1.02, and the LoA showed differences to be within wider limits -51.16 lower and 53.02 upper). Our results suggest that RC can determine rumination activity and are an alternative to visual observations when animals are housed indoors. However, they are not an alternative to direct observations with grazing animals on pasture and its use is not advisable until further research and validation are carried out. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Observed Oceanic Response over the Upper Continental Slope and Outer Shelf during Hurricane Ivan

DTIC Science & Technology

2007-09-01

the slope and rise. In addition, they were presumed to be along-shelf and cross-shelf components of group veloci- generated by pulsations of the Loop ...hits. Fortunately, all of exchange of mass, momentum, heat , and water proper- the SEED moorings survived this powerful storm and ties across the shelf...15. SUBJECT TERMS SEED, continental shelf, Doppler, waves 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF 18. NUMBER 19a. NAME OF RESPONSIBLE

Carbon dynamics within agricultural and native sites in the loess region of Western lowa

USGS Publications Warehouse

Manies, K.L.; Harden, J.W.; Kramer, L.; Parton, W.J.

2001-01-01

In order to quantify the historical changes in carbon storage that result from agricultural conversion, this study compared the carbon dynamics of two sites in the loess region of Iowa: a native prairie and a cropland. Field data were obtained to determine present-day carbon storage and its variability within a landscape (a stable ridgetop vs. eroding upper-midslope vs. depositional lower slope). Models were used to recreate the historical carbon budget of these sites and determine the cropland's potential to be a net CO2 source or sink, relative to the atmosphere. Regardless of slope position, the cropland site contains approximately half the amount of carbon as prairie. Variability in soil carbon storage within a site as a consequence of slope position is as large or larger (variations of 200-300%) than temporal variation (???200% at all slope positions). The most extreme difference in soil carbon storage between the cropland and prairie sites is found in the soil at the upper-midslope, which is the area of greatest erosion. The models estimate that 93-172% of the carbon in the original topsoil has been lost from the cropland's eroding midslope. Much of this carbon is derived from deeper soil horizons. Either a small sink or strong source of carbon to the atmosphere is created, depending on the fate of the eroded sediment and its associated carbon.

A model study of sediment transport across the shelf break

NASA Astrophysics Data System (ADS)

Marchal, Olivier

2017-04-01

A variety of dynamical processes can contribute to the transport of material (e.g., particulate matter) across the shelf break - the region separating the continental shelf from the continental slope. Among these processes are (i) the reflection of internal waves on the outer shelf and upper slope, and (ii) the instability of hydrographic fronts, roughly aligned with isobaths, that are often present at the shelf break. On the one hand, internal waves reflecting on a sloping boundary can produce bottom shear stresses that are large enough to resuspend non-cohesive sediments into the water column. On the other hand, eddies shed from unstable shelf break fronts can incorporate into their core particle-rich waters from the outer shelf and upper slope, and transport these waters offshore. Here we present numerical experiments with a three-dimensional numerical model of ocean circulation and sediment transport, which illustrate the joint effect of internal waves and eddies on sediment transport across the shelf break. The model is based on the primitive equations and terrain-following coordinates. The model domain is square and idealized, comprising a flat continental shelf, a constant continental slope, and a flat abyssal basin. The model grid has O(1 km) horizontal resolution, so that (sub)mesoscale eddies observed in the vicinity of shelf breaks, such as south of New England, can be represented in detail. Internal waves are excited through the specification of a periodic variation in the across-slope component of velocity at the offshore boundary of the domain, and eddies are generated from the baroclinic instability of a shelf break jet that is initially in strict thermal wind balance. Numerical experiments are conducted that are characterized by (i) different slopes of internal wave characteristics relative to the continental slope, representing sub-critical, critical, and super-critical regimes, and (ii) different values for the dimensionless ratios that emerge from the linear stability analysis of shelf break fronts. Emphasis is placed on the physical conditions that are conducive to the formation and maintenance of bottom and intermediate nepheloid layers - the particle-rich layers that are often observed near oceanic margins in the traces of optical instruments.

Fundamental aerodynamic characteristics of delta wings with leading-edge vortex flows

NASA Technical Reports Server (NTRS)

Wood, R. M.; Miller, D. S.

1985-01-01

An investigation of the aerodynamics of sharp leading-edge delta wings at supersonic speeds has been conducted. The supporting experimental data for this investigation were taken from published force, pressure, and flow-visualization data in which the Mach number normal to the wing leading edge is always less than 1.0. The individual upper- and lower-surface nonlinear characteristics for uncambered delta wings are determined and presented in three charts. The upper-surface data show that both the normal-force coefficient and minimum pressure coefficient increase nonlinearly with a decreasing slope with increasing angle of attack. The lower-surface normal-force coefficient was shown to be independent of Mach number and to increase nonlinearly, with an increasing slope, with increasing angle of attack. These charts are then used to define a wing-design space for sharp leading-edge delta wings.

Controls of bioclastic turbidite deposition in eastern Muertos Trough northeast Caribbean Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forsthoff, G.M.; Holcombe, T.L.

1985-02-01

A study of seismic-reflection profiles and sediment cores establishes regional bathymetric and source area control over the composition, transport, and distribution of turbidites in the eastern Muertos Trough, Bioclastic (carbonate) turbidites dominate the eastern portion of the trough. Analyses of carbon content and sand-sized components suggest that the bioclastic turbidites (characterized by planktonic foraminifera, pteropods, and sponge spicules) are reworked pelagic oozes originally deposited on the outer-shelf and upper-slope areas south of St. Croix and eastern Puerto Rico. The presence of several intrashelf and upper-slope basins prohibits shallow-water carbonate sediments from entering the Muertos Trough. Volcanic rock fragments derived frommore » Puerto Rico are transported to the trough via the Guayanilla Canyon system. Mixing of the volcanic fragments with outer-shelf and upper-slope lutites results in mixed bioclastic-terrigenous turbidites south of central and western Puerto Rico. The paucity of shallow-water carbonate sediments in the trough suggests that the submarine canyons are effective conduits for the rapid transport of volcaniclastic sands across the shelf and thereby prevent extensive mixing with inner- and middle-shelf carbonate sediments. Sediment transport within the trough is primarily axial in an east-west direction. Outer trench-wall fault scarps, south of Guayanilla Canyon, limit the southerly progradation of the trench-wedge facies and deflect incoming gravity flows in a down-axis (westward) direction. Where no faults exist, the trench wedge progrades southward and interfingers with the pelagic sediments of the northern Venezuelan basin.« less

Active deformation and evolution of the upper forearc slope of the central Ryukyu Arc, northwestern Pacific

NASA Astrophysics Data System (ADS)

Arai, K.; Inoue, T.; Sato, T.

2016-12-01

The Ryukyu Arc, which extend for over 1200 km along the east coast of Asia from Kyushu to Taiwan, and the associated Ryukyu Trench, are products of the subduction of the Philippine Sea Plate beneath the Eurasian Plate. The Okinawa Trough, a back-arc basin located landward of the Ryukyu Arc, formed in the Late Miocene (Gungor et al., 2012) or the Late Pliocene-Early Pleistocene (Sibuet et al., 1998); its formation is a key geologic event associated with complex tectonic movements and changes in the topographic configuration of the Ryukyu Arc. Geological Survey of Japan (GSJ), AIST has started the marine geological mapping project around Ryukyu Arc since the 2008 FY. Multi channel (16 ch) high-resolution seismic profiles were acquired during these cruises by the GI-gun (355cu. inch) or the Cluster-gun (30+30 cu. inch) systems. Survey area in the southeast off Okinawa Island is located on the upper forearc slope along the Ryukyu Trench. Seismic reflections of shelf and the upper forearc slope show no obvious deformation such as the fold and faults parallel to the Ryukyu Trench axis. In contrast, some active faults, which were perpendicular to the Ryukyu Trench axis (NW-SE direction), were observed. An acoustic basement, which is characterized distinct reflector had tilted southeastward (trenchward) and was unconformable overlain by the stratified sediments. These sediments divided into four seismic units. We present the geological history and tectonics of the central Ryukyu Arc.

Pressure-temperature phase diagrams of CaK(Fe1 -xNix)4As4 superconductors

NASA Astrophysics Data System (ADS)

Xiang, Li; Meier, William R.; Xu, Mingyu; Kaluarachchi, Udhara S.; Bud'ko, Sergey L.; Canfield, Paul C.

2018-05-01

The pressure dependence of the magnetic and superconducting transitions and that of the superconducting upper critical field are reported for CaK (Fe1-xNix) 4As4 , the first example of an Fe-based superconductor with spin-vortex-crystal-type magnetic ordering. Resistance measurements were performed on single crystals with two substitution levels (x =0.033 ,0.050 ) under hydrostatic pressures up to 5.12 GPa and in magnetic fields up to 9 T. Our results show that, for both compositions, magnetic transition temperatures TN are suppressed upon applying pressure; the superconducting transition temperatures Tc are suppressed by pressure as well, except for x =0.050 in the pressure region where TN and Tc cross. Furthermore, the pressure associated with the crossing of the TN and Tc lines also coincides with a minimum in the normalized slope of the superconducting upper critical field, consistent with a likely Fermi-surface reconstruction associated with the loss of magnetic ordering. Finally, at p ˜4 GPa, both Ni-substituted CaK (Fe1-xNix) 4As4 samples likely go through a half-collapsed-tetragonal phase transition, similar to the parent compound CaKFe4As4 .

Laser Scanning for the definition of high resolution topography in the Apuan Alps (IT) marble district

NASA Astrophysics Data System (ADS)

Riccucci, Silvia; Salvini, Riccardo; Francioni, Mirko

2010-05-01

The present paper describes the results of five laser scanning surveys performed by a Leica™ ScanStation2 with the aim of producing an high definition topography of a quarry, at the scale of 1:1,000. The project comes from a joint research carried out by the Authors in collaboration with the Local Sanitary Unit Agency (ASL n.1) of Massa and Carrara (IT). The main objective of this work has been the survey of both the exploited quarry walls and the upper residual and natural slopes. The area of interest is characterized by several quarry fronts which develop to variable and alternate directions to create very evident rock spurs, from NW-SE to NE-SW trending for a total wideness of about 2 hectares. Moreover, the quarry walls are sub-vertical and sometimes overhang by a total height of 100 m in respect to the quarry floor. Differential GPS and orthometric correction have been applied in order to co-register and to georeference the five point clouds; for these purposes a series of optical targets have been measured using a Laser Total Station. The subsequent phase has been the mesh construction and editing, from which a topographic map, 25 cm equidistance contours lines, has been created. The planimetric map shows the position and the geometry of crests, banks, escarpments, walls and all others exploitation features and the characteristics of the upper natural slopes. Morphological profiles along the maximum slope have been realized in order to better plan the future extractive activities according to the regional law. In order to make easier the prospective observation of detailed and overall areas, 3D views of multi-directional orientation have been realized. The produced data has been published by using the free LeicaTM TruView plug-in for Internet Explorer in a way to easily view the photographs and to measure the laser scan point clouds. Processing results have highlighted the higher spatial resolution of data coming from laser scanning in respect to the traditional topographic methodologies. Such information can be used for multitemporal evaluation of mining volumes. For local authorities the control of extraction volumes can be more easily and rapidly executed by map algebra function of image differencing between bi-temporal Digital Dense Surface Model (DDSM) of the quarry walls. Finally, the DDSM has been utilized by the Authors to analyze the rock slope stability, to collect geological-engineering data, such as joints attitude and spacing, and to perform detailed analysis of rockfall trajectories.

Long-term research -- why do we do it?

Treesearch

Bill Leak

2013-01-01

While jotting down some notes for this forword, I’m also thinking about how the day was spent in the upper elevations of the Bartlett Experimental Forest planning out a monitoring scheme for an early upper-slope harvest in an oak stand. The previous several weeks were spent in relocating cruise lines for some 450-500 permanent plots established in 1931-32. And it’s...

Evaluating channel morphologic changes and bed-material transport using airborne lidar, upper Colorado River, Rocky Mountain National Park, Colorado

NASA Astrophysics Data System (ADS)

Mangano, Joseph F.

A debris flow associated with the 2003 breach of Grand Ditch in Rocky Mountain National Park, Colorado provided an opportunity to determine controls on channel geomorphic responses following a large sedimentation event. Due to the remote site location and high spatial and temporal variability of processes controlling channel response, repeat airborne lidar surveys in 2004 and 2012 were used to capture conditions along the upper Colorado River and tributary Lulu Creek i) one year following the initial debris flow, and ii) following two bankfull flows (2009 and 2010) and a record-breaking long duration, high intensity snowmelt runoff season (2011). Locations and volumes of aggradation and degradation were determined using lidar differencing. Channel and valley metrics measured from the lidar surveys included water surface slope, valley slope, changes in bankfull width, sinuosity, braiding index, channel migration, valley confinement, height above the water surface along the floodplain, and longitudinal profiles. Reaches of aggradation and degradation along the upper Colorado River are influenced by valley confinement and local controls. Aggradational reaches occurred predominantly in locations where the valley was unconfined and valley slope remained constant through the length of the reach. Channel avulsions, migration, and changes in sinuosity were common in all unconfined reaches, whether aggradational or degradational. Bankfull width in both aggradational and degradational reaches showed greater changes closer to the sediment source, with the magnitude of change decreasing downstream. Local variations in channel morphology, site specific channel conditions, and the distance from the sediment source influence the balance of transport supply and capacity and, therefore, locations of aggradation, degradation, and associated morphologic changes. Additionally, a complex response initially seen in repeat cross-sections is broadly supported by lidar differencing, although the differencing captures only the net change over eight years and not annual changes. Lidar differencing shows great promise because it reveals vertical and horizontal trends in morphologic changes at a high resolution over a large area. Repeat lidar surveys were also used to create a sediment budget along the upper Colorado River by means of the morphologic inverse method. In addition to the geomorphic changes detected by lidar, several levels of attrition of the weak clasts within debris flow sediment were applied to the sediment budget to reduce gaps in expected inputs and outputs. Bed-material estimates using the morphologic inverse method were greater than field-measured transport estimates, but the two were within an order of magnitude. Field measurements and observations are critical for robust interpretation of the lidar-based analyses because applying lidar differencing without field control may not identify local controls on valley and channel geometry and sediment characteristics. The final sediment budget helps define variability in bed-material transport and constrain transport rates through the site, which will be beneficial for restoration planning. The morphologic inverse method approach using repeat lidar surveys appears promising, especially if lidar resolution is similar between sequential surveys.

Modeling granular material flows: The angle of repose, fluidization and the cliff collapse problem

NASA Astrophysics Data System (ADS)

Holsapple, Keith A.

2013-07-01

I discuss theories of granular material flows, with application to granular flows on the earth and planets. There are two goals. First, there is a lingering belief of some that the standard continuum plasticity Mohr-Coulomb and/or Drucker-Prager models are not adequate for many large-scale granular flow problems. The stated reason for those beliefs is the fact that the final slopes of the run-outs in collapse, landslide problems, and large-scale cratering are well below the angle of repose of the material. That observation, combined with the supposition that in those models flow cannot occur with slopes less than the angle of repose, has led to a number of researchers suggesting a need for lubrication or fluidization mechanisms and modeling. That issue is investigated in detail and shown to be false. A complete analysis of slope failures according to the Mohr-Coulomb model is presented, with special attention to the relations between the angle of repose and slope failures. It is shown that slope failure can occur for slope angles both larger than and smaller than the angle of repose. Second, to study the details of landslide run-outs, finite-difference continuum code simulations of the prototypical cliff collapse problem, using the classical plasticity models, are presented, analyzed and compared to experiments. Although devoid of any additional fluidization models, those simulations match experiments in the literature extremely well. The dynamics of this problem introduces additional important features relating to the run-out and final slope angles. The vertical free surface begins to fall at the initial 90° and flow continues to a final slope less than 10°. The detail in the calculation is examined to show why flow persists at slope angles that appear to be less than the angle of repose. The motions include regions of solid-like, fluid-like, and gas-like flows without invoking any additional models.

A sagging along the eastern Chianti Mts., Italy

NASA Astrophysics Data System (ADS)

Coltorti, M.; Ravani, S.; Cornamusini, G.; Ielpi, A.; Verrazzani, F.

2009-11-01

A deep-seated gravitational slope deformation (DGSD) affects the eastern side of the Chianti Mts. Ridge. It develops in an N-S to NW-SE direction and is > 10 km wide and 3-4 km long. This area corresponds to the eastern side of a main antiform, characterised by east-verging folds and thrusts involving bedrock of the Mesozoic-Paleogene Tuscan Units, particularly sandstones containing interlayered highly fractured and deformed Ligurian rocks (shales and limestones with olistostromes). The foot of the slope is characterised by tilted Plio-Pleistocene deposits unconformably sealing the bedrock structures as folds, thrusts and faults. The most significant morphological features are a main escarpment, trenches, several secondary and counter-slope escarpments that together indicate large-scale gravitational phenomena. The main escarpment is responsible for the headward retreat of the slope, and is deeply segmented by numerous arcuate niches that reveal differential movements of single blocks. The DGSD is also dissected by SW-NE trending streams that often deepen inside the N-S trenches. Minor landslides due to local instability are also present. At the foot of the slope, the older continental Pliocene deposits of the Upper Valdarno Basin crop out. Although tilted by tectonic movements, the deposits have not been severely affected by gravitational deformations. This indicates that the movement is a typical sagging, a large landslide at an embryonic stage, affecting the upper part of the slope but not reaching the valley bottom. The deformations are absorbed in the rock mass which is also partially drained by stream incision that prevents high pore pressure. The occurrence of down-slope and down-movement facing escarpments and up-slope and up-movement facing counter-slope escarpments indicate a sagging characterised by a listric spoon-shaped geometry. The DGSD has a style similar to crustal extensional tectonics such as Morton and Black's crustal attenuation model. Although few chronological indications of movements are present, the fact that Late Pleistocene debris deposits, widespread in the northern and central Apennines, are not found at the contact between the escarpment and the trenches suggests a post-glacial activity for at least part of the movements. Recognizing embryonic-stage collapse is of primary importance in assessing geological hazard and risk because rapid evolution and collapse could follow.

Slope Stability Estimation of the Kościuszko Mound in Cracow

NASA Astrophysics Data System (ADS)

Wrana, Bogumił; Pietrzak, Natalia

2015-06-01

In the paper, the slope stability problem of the Kościuszko Mound in Cracow, Poland is considered. The slope stability analysis was performed using Plaxis FEM program. The outer surface of the mound has complex geometry. The slope of the cone is not uniform in all directions, on the surface of the cone are pedestrian paths. Due to its complicated geometry it was impossible to do computing by Plaxis input pre-procesor. The initial element mesh was generated using Autodesk Autocad 3D and next it was updated by Plaxis program. The soil parameters were adopted in accordance with the detailed geological soil testing performed in 2012. Calculating model includes geogrids. The upper part was covered by MacMat geogrid, while the lower part of the Mound was reinforced using Terramesh Matt geogrid. The slope analysis was performed by successives reduction of φ /c parameters. The total multiplayer ΣMsf is used to define the value of the soil strength parameters. The article presents the results of slope stability before and after the rainfall during 33 days of precipitation in flood of 2010.

Origin of Florida Canyon and the role of spring sapping on the formation of submarine box canyons

USGS Publications Warehouse

Paull, Charles K.; Spiess, Fred N.; Curray, Joseph R.; Twichell, David C.

1990-01-01

Florida Canyon, one of a series of major submarine canyons on the southwestern edge of the Florida Platform, was surveyed using GLORIA, SeaBeam, and Deep-Tow technologies, and it was directly observed during three DSRV Alvin dives. Florida Canyon exhibits two distinct morphologies: a broad V-shaped upper canyon and a deeply entrenched, flat-floored, U-shaped lower canyon. The flat- floored lower canyon extends 20 km into the Florida Platform from the abyssal Gulf. The lower canyon ends abruptly at an ∼3 km in diameter semicircular headwall that rises 750 m with a >60° slope angle to the foot of the upper canyon. The sides of the lower canyon are less steep than its headwall and are characterized by straight faces that occur along preferred orientations and indicate a strong joint control. The upper canyon is characterized by a gently sloping, straight V-shaped central valley cut into a broad terrace. The flat floor of the upper canyon continues as terraces along the upper walls of the lower canyon. On the flanks of the upper canyon, there are five >50-m-deep, >0.5-km-wide, closed sink-hole-like depressions which indicate subsurface dissolution within the platform. The origin of the lower canyon is difficult to explain with traditional models of submarine canyon formation by external physical processes. The movement of ground water, probably with high salinities and reduced compounds along regional joints, may have focused the corrosive force of submarine spring sapping at the head of the lower canyon to produce the canyon's present shape.

Climatic-oceanic forcing on the organic accumulation across the shelf during the Early Cambrian (Age 2 through 3) in the mid-upper Yangtze Block, NE Guizhou, South China

NASA Astrophysics Data System (ADS)

Yeasmin, Rumana; Chen, Daizhao; Fu, Yong; Wang, Jianguo; Guo, Zenghui; Guo, Chuan

2017-02-01

The organic-rich sediments were widely deposited over the entire Yangtze Block during the Early Cambrian (late Nemakit-Daldynian to Botomian). In the mid-upper Yangtze region, northeastern Guizhou, South China, they comprise, in ascending order, the Niutitang, Jiumenchong and lower Bianmachong formations which are dominated by black shales except the middle one characterized by interbedded shales-limestones. Three third-order depositional sequences are identified in the two studied sections located on the upper slope to basin of the open shelf. The organic-rich sediments were mostly deposited notably during transgressions on the shallower upper slope-margin (TOC up to 25 wt.%) where they are characterized by co-increases in C, P, Fe, and Ba concentrations, indicating the highest organic productivity and coupled C, P and Fe cycling there. In contrast, in the shelf basin, the concomitant organic-rich sediments yield lower organic (TOC <10 wt.% mostly) and Ba abundances, and generally show antithetic relationship of TOC with P and Fe variations, indicative of a relatively low organic productivity and transient decoupled C, P and Fe cycling in the deeper basin. This spatial difference in C, P, Fe and Ba cycling as a whole thus indicate that the highest organic productivity wedge on the shallower shelf upper slope-margin was likely induced by the oceanic upwelling from the restricted basin where the P and Fe nutrients were transiently depleted without timely renewal. Meanwhile, multiple redox proxies, including V/Al, Ni/Al and Cr/Al ratios vs. TOC contents, together with V/(V + Ni) and V/Cr ratios, generally characterize a more severe euxinic water wedge localized on the shallower upper slope-margin of shelf where the organic production culminated, but a nonsulfidic (ferruginous) anoxic state in the basin due to the relatively low sulfate level. Meanwhile, episodic depletion of trace elements in the deeper basin during the higher organic productivity also reconciles the concomitantly enhanced upwelling from the somewhat restricted deep watermass likely silled by the underwater upland seaward. The coincidence of organic-rich intervals with more arid climate epoches, as shown by increased Ti/Al ratios indicative of increased aeolian fluxes, reconciles a subtropical arid climate of Yangtze Block within the north mid-low-latitude trade-wind zone during deposition (the Early Cambrian). As such, enhanced offshore currents driven by the trade winds could have further induced the upwelling of nutrient-rich deep waters along the shelf during the transgressions, although tended to wane onwards, leading to the tempo-spatial heterogeneities in organic production and redox state across the shelf sea.

Downward Slope

NASA Technical Reports Server (NTRS)

2004-01-01

This false-color image from NASA's Mars Exploration Rover Opportunity panoramic camera shows a downward view from the rover as it sits at the edge of 'Endurance' crater. The gradual, 'blueberry'-strewn slope before the rover contains an exposed dark layer of rock that wraps around the upper section of the crater. Scientists suspect that this rock layer will provide clues about Mars' distant past. This mosaic image comprises images taken from 10 rover positions using 750, 530 and 430 nanometer filters, acquired on sol 131 (June 6, 2004).

Flood Plain Information Brandywine Creek, New Castle County, Delaware.

DTIC Science & Technology

1973-07-01

The Brandywine’s course through Delaware is fairly straight and cuts through a valley of rugged terrain. The adjacent land slopes that comprise its...varies sharply in 3 distinct reaches. The upper reach from the State Line to Rockland Road falls 15.5 feet at a slope of 4.9 feet per mile. The middle...Mileage Above Drainage Area Location Mouth Tributary Total sq. Mi. sq. mi. Pennsy lvania-Del aware State Line 10.55 ... 299.9 Confluence with Beaver

Migration of 137Cs in the soil of sloping semi-natural ecosystems in Northern Greece.

PubMed

Arapis, G D; Karandinos, M G

2004-01-01

In the present study, the 137Cs concentration in the soil of sloping semi-natural ecosystems at four different regions of Western Macedonia in Greece was measured 10 years after the Chernobyl accident. These regions were highly polluted due to the deposition of radionuclides escaped during the accident. The concentrations of 137Cs measured were found to differ significantly among the four regions. The rates of both horizontal and vertical migration in the soil were also evaluated. The vertical migration velocity of 137Cs was found to range from 0.1 to 0.3 cm per year, in the most contaminated areas. Consequently, 10 years following the Chernobyl accident, the bulk of 137Cs deposited over the surface of the studied areas in Greece was found to be restricted in the upper 5 cm layer of soil. Regarding the horizontal migration, in most of the sampling sites, we did not detect any displacement or trend to movement of radiocaesium on the surface from the upper to the lower levels of the slopes. Instead, we recorded decreased concentrations of 137Cs with the decrease of altitude.

Solution algorithm of dwell time in slope-based figuring model

NASA Astrophysics Data System (ADS)

Li, Yong; Zhou, Lin

2017-10-01

Surface slope profile is commonly used to evaluate X-ray reflective optics, which is used in synchrotron radiation beam. Moreover, the measurement result of measuring instrument for X-ray reflective optics is usually the surface slope profile rather than the surface height profile. To avoid the conversion error, the slope-based figuring model is introduced introduced by processing the X-ray reflective optics based on surface height-based model. However, the pulse iteration method, which can quickly obtain the dell time solution of the traditional height-based figuring model, is not applied to the slope-based figuring model because property of the slope removal function have both positive and negative values and complex asymmetric structure. To overcome this problem, we established the optimal mathematical model for the dwell time solution, By introducing the upper and lower limits of the dwell time and the time gradient constraint. Then we used the constrained least squares algorithm to solve the dwell time in slope-based figuring model. To validate the proposed algorithm, simulations and experiments are conducted. A flat mirror with effective aperture of 80 mm is polished on the ion beam machine. After iterative polishing three times, the surface slope profile error of the workpiece is converged from RMS 5.65 μrad to RMS 1.12 μrad.

Does Late Miocene Exhumation Along the Western Slope of the Colorado Rockies Reflect Differential Rock Uplift?

NASA Astrophysics Data System (ADS)

Rosenberg, R. H.; Kirby, E.; Aslan, A.; Karlstrom, K. E.; Heizler, M. T.; Kelley, S. A.; Piotraschke, R. E.; Furlong, K. P.

2011-12-01

It is increasingly recognized that dynamic effects associated with changes in mantle flow and buoyancy can influence the evolution of surface topography. In the Rocky Mountain province of the western United States, recent seismic deployments reveal intriguing correlations between anomalies in the velocity structure of the upper mantle and regions of high topography. Here, we investigate whether regional correlations between upper-mantle structure and topography are associated with the history of Late Cenozoic fluvial incision and exhumation. Major tributaries of the upper Colorado River, including the Gunnison and Dolores Rivers, which drain high topography in central and western Colorado overlie upper mantle with slow seismic wave velocities; these drainages exhibit relatively steep longitudinal profiles (normalized for differences in drainage area and discharge) and are associated with ~1000-1500 m of incision over the past 10 Ma. In contrast, tributaries of the Green River that drain the western slope in northern Colorado (White, Yampa, and Little Snake Rivers) overlie mantle of progressively higher seismic wave velocities. River profiles in northern Colorado are two to three times less steep along reaches with comparable bedrock lithologies. New Ar39/Ar40 ages on ~11 Ma basalt flows capping the Tertiary Brown's Park Formation in northern Colorado indicate that the magnitude of exhumation along these profiles ranges from ~400 - 600 m over this time interval. The correspondence of steep river profiles in regions of greater incision implies that the fluvial systems are dynamically adjusting to an external forcing. New constraints on the exhumation history of the upper Colorado River from apatite fission track ages in boreholes near Rifle, Colorado are best explained by an onset of exhumation at ca. 8-10 Ma. Thus, relative base level fall associated with development of Grand Canyon (ca. 6-5 Ma) does not explain the regional onset of incision along the western slope of the Rockies. Additionally, new cosmogenic burial ages from fan-terrace complexes near Rifle, Colorado show that Colorado River incision occurred at similar rates over both 10 Ma and 2 Ma timescales. Fluvial incision in response to relative base level fall or to changes in regional climate cannot easily explain the history of differential incision along the western slope. Given the correspondence of steep channels, large magnitude incision and regions of low seismic velocity mantle, we suggest that differential rock uplift, driven, in part, by differences in the buoyancy and/or convective flow of the mantle beneath western Colorado is the likely driver for Neogene incision.

Submarine canyon formation and evolution in the Argentine Continental Margin between 44°30'S and 48°S

NASA Astrophysics Data System (ADS)

Lastras, G.; Acosta, J.; Muñoz, A.; Canals, M.

2011-05-01

In the framework of the Vulnerable Marine Ecosystems (VME) of the High Seas of the South West Atlantic, large areas of the Argentine Continental Margin (ACM) between 44°30'S and 48°S have been swath-mapped for the first time, obtaining full data coverage of the seafloor in this region between the outermost continental shelf and the middle slope down to 1600 m water depth. The slope is characterized by the presence of smooth terraces (Nagera, Perito Moreno and Piedra Buena) that widen towards the south, limited by morphological steps with evident signs of erosion in the form of scours. These terraces form part of the Argentine contourite depositional systems, generated by the interaction of the northwards flowing Antarctic water masses with the seafloor. Within the studied area, seven canyons and their multiple branches dissect the upper and middle continental slopes, from west to east, across the terraces and the steps. These canyons, which belong to the Patagonia submarine canyon system and are collected at a depth of ~ 3.5 km by a slope-parallel, SSW-NNE-oriented channel known as the Almirante Brown transverse canyon, display a large variety of morphologies. These include incisions from just a dozen of metres to 650 m, straight to highly meandering sections with sharp bends, well-developed levees and walls that reach 35° in slope gradient, hanging branches, conspicuous axial incisions and multiple knickpoints. Only the northernmost canyon indents in the continental shelf, whereas the others start at the limit between the upper and middle slopes, and are often fed by small, straight, leveed gullies. The action of both across-slope processes represented by submarine canyons and along-slope processes represented by terracing and scouring conform the ACM as a peculiar mixed margin, with the presence of both contour and gravity currents at the same place at the same time. We propose that at present, along-slope erosion and transport mainly occurs along the Perito Moreno terrace, whereas across-slope processes are much more dominant in the Nagera terrace. Erosive bedforms such as crescent scours, generated by contour currents, contribute to the progressive bottom-up erosion of the Nagera terrace and act as an initial collector of across-slope transported sediment, that later, due to flow focusing and recurrence, incise and interconnect creating definitive canyons that progress upslope by retrogressive erosion until their head indents the shelf break. Changes in the balance between across-slope and along-slope transport would imply a disequilibrium in the combination of processes leading to canyon formation, producing canyon abandonment, and partial or total filling. These changes could be produced by a variation in the depth of the main interfaces of Antarctic water masses leading to either an increase or a decrease in the erosion and transport capacity of contour currents, and/or by an enhancement of across-slope transport related to an increase of sediment availability.

Rapid subsidence along the Kerama Gap on the Ryukyu Arc, northwestern Pacific

NASA Astrophysics Data System (ADS)

Arai, K.; Inoue, T.; Sato, T.

2017-12-01

The Ryukyu Arc, which extend for over 1200 km along the east coast of Asia from Kyushu to Taiwan, and the associated Ryukyu Trench, are products of the subduction of the Philippine Sea Plate beneath the Eurasian Plate. The Okinawa Trough, a back-arc basin located landward of the Ryukyu Arc, formed in the Late Miocene (Gungor et al., 2012) or the Late Pliocene-Early Pleistocene (Sibuet et al., 1998); its formation is a key geologic event associated with complex tectonic movements and changes in the topographic configuration of the Ryukyu Arc. Geological Survey of Japan (GSJ), AIST has started the marine geological mapping project around the Ryukyu Arc since the 2008 FY. Multi channel (16 ch) high-resolution seismic profiles were acquired during these cruises by the GI-gun (355cu. inch) or the Cluster-gun (30+30 cu. inch) systems. Our survey area around the Okinawa Island is characterized by the shelf, upper forearc slope and slope to the back-arc basin. Seismic reflections of shelf and the upper forearc slope show a distinct reflector which may represent erosional unconformable surface. The distinct reflector had mainly tilted southeastward and was overlain by the stratified sediments. No obvious deformation such as the fold and faults parallel to the Ryukyu Trench axis was found under the upper forearc slope. In contrast, some active faults which were perpendicular to the Ryukyu Trench axis (NW-SE direction) were observed. The most conspicuous normal faults system under the Kerama Gap located on southwest off the Okinawa Island is formed. We will present the seismic profiles around the Kerama Gap. Seismic profiles show a distinct, irregularly undulated reflector as an acoustic basement around the Kerama Gap. The acoustic basement is overlain by the clear stratified sediments. Many normal faults developed NW-SE direction cut the stratified sediments and are deformed the subsurface along the Kerama Gap. Subsidence of the Kerama Gap resulted from large vertical downthrows of NW-SE trending normal faults.

Diversity, distribution and population size structure of deep Mediterranean gorgonian assemblages (Menorca Channel, Western Mediterranean Sea)

NASA Astrophysics Data System (ADS)

Grinyó, Jordi; Gori, Andrea; Ambroso, Stefano; Purroy, Ariadna; Calatayud, Clara; Dominguez-Carrió, Carlos; Coppari, Martina; Lo Iacono, Claudio; López-González, Pablo J.; Gili, Josep-Maria

2016-06-01

Gorgonians are a key group of organisms in benthic marine communities with a wide bathymetric and geographical distribution. Although their presence on continental shelves and slopes has been known for more than 100 years, knowledge concerning the ecology of deep gorgonian species is still in a very preliminary stage. To overcome this situation, gorgonian assemblages located at 40-360 m depth were studied over a large geographical area on the continental shelf and upper slope of the Menorca Channel (Western Mediterranean Sea). A quantitative analysis of video transects recorded by a manned submersible and a remotely operated vehicle, were used to examine the diversity, distribution and demography of gorgonian species. Results showed high gorgonian diversity within this depth range (a total of nine species were observed) compared to Mediterranean coastal areas. Gorgonian assemblages on the continental shelf and upper slope were mostly monospecific (respectively 73% and 76% of occupied sampling units contained one single species), whereas shelf edge assemblages were highly multispecific (92% of occupied sampling units contained several species). This contrasts with the monospecificity of Mediterranean coastal gorgonian assemblages. Gorgonian populations on the continental shelf were mostly dominated by small colonies (88% of measured colonies) with few intermediate and large colonies (12% of measured colonies). In deeper areas small colonies were still dominant (60% of measured colonies), but intermediate and large colonies were much more abundant (40% of measured colonies). This suggests high recruitment rates on the continental shelf, but perturbations (trammel nets, long lines and strong storms) may limit the presence of intermediate and large colonies. Conversely, on the shelf edge and upper slope a more stable environment may allow colonies to reach larger dimensions. The identification and ecological characterization of these deep assemblages further extends the current knowledge about Mediterranean gorgonians, and is fundamental in improving the management and conservation of deep benthic ecosystems.

Catalogs of micro-seismicity recorded at the Pechgraben landslide (Upper Austria)

NASA Astrophysics Data System (ADS)

Provost, Floriane; Hibert, Clément; Vouillamoz, Naomi; Malet, Jean-Philippe; Ottowitz, David; Jochum, Birgit

2017-04-01

The microseismicity activity of soft-rock landslides (i.e. developed in clays and clay-shales) present various types of seismic event associated with the slope deformation. They are assumed to be linked to the slip at the interface with the bedrock or at the boundaries of the landslide, to material failures, to fissure openings or to fluid transfers within the medium. It is currently necessary to document the microseismicity generated by soft-rock landslides on a larger amount of instrumented slopes in order to validate the current seismic typology and understand the source mechanisms in relation with the deformation. Previous studies have shown the interest of the Pechgraben (Upper Austria) clay-shale landslide for such documentation. This landslide was reactivated in summer 2013 after heavy rainfalls and is characterized by a shallow bedrock (<10m) and varying displacement rates in space and time (from mm.day-1 to cm.day-1). A short pilot seismic campaign (<9 days) was carried out in 2015 and micro-earthquakes as well as episodic tremor-like signals were recorded. A new passive seismic campaign was conducted during one month in November-December 2016. Two broadband three-component seismometers were installed facing each other on the two stable borders of the slope with one tripartite seismic array deployed in the center, on top of the most active area of the landslide. The deformation pattern of the slope was monitored remotely with a ground-based InSAR at a high frequency (10 min). This study aims to present the variety of seismic sources generated by the landslide, using supervised machine learning algorithms for event detection and classification, and to correlate the resulting micro-seismic catalog with the changes in time of the slope deformation.

An approach to understanding hydrologic connectivity on the hillslope and the implications for nutrient transport

USGS Publications Warehouse

Stieglitz, M.; Shaman, J.; McNamara, J.; Engel, V.; Shanley, J.; Kling, G.W.

2003-01-01

Hydrologic processes control much of the export of organic matter and nutrients from the land surface. It is the variability of these hydrologic processes that produces variable patterns of nutrient transport in both space and time. In this paper, we explore how hydrologic "connectivity" potentially affects nutrient transport. Hydrologic connectivity is defined as the condition by which disparate regions on the hillslope are linked via subsurface water flow. We present simulations that suggest that for much of the year, water draining through a catchment is spatially isolated. Only rarely, during storm and snowmelt events when antecedent soil moisture is high, do our simulations suggest that mid-slope saturation (or near saturation) occurs and that a catchment connects from ridge to valley. Observations during snowmelt at a small headwater catchment in Idaho are consistent with these model simulations. During early season discharge episodes, in which the mid-slope soil column is not saturated, the electrical conductivity in the stream remains low, reflecting a restricted, local (lower slope) source of stream water and the continued isolation of upper and mid-slope soil water and nutrients from the stream system. Increased streamflow and higher stream water electrical conductivity, presumably reflecting the release of water from the upper reaches of the catchment, are simultaneously observed when the mid-slope becomes sufficiently wet. This study provides preliminary evidence that the seasonal timing of hydrologic connectivity may affect a range of ecological processes, including downslope nutrient transport, C/N cycling, and biological productivity along the toposequence. A better elucidation of hydrologic connectivity will be necessary for understanding local processes as well as material export from land to water at regional and global scales. Copyright 2003 by the American Geophysical Union.

Himalayan Sackung and Associations to Regional Structure

NASA Astrophysics Data System (ADS)

Shroder, J. F.; Bishop, M. P.; Olsenholler, J.

2003-12-01

Recognition of sackung slope failure or deep-seated, rock-slope deformation in the Himalaya has been rather limited, in part because: (1) many geoscientists do not recognize its characteristics; (2) large-scale aerial photographs and topographic maps used to identify the characteristic surficial, topographic manifestations of the failure type are commonly low-level state secrets in that region; and (3) no systematic survey for sackung has ever been made in the Himalaya. In the Pakistani-controlled, western Himalaya, some unconventional access to aerial photographs in the Kaghan and Nanga Parbat areas allowed first recognition of several characteristic ridge-top grabens and anti-slope scarps. Later release of declassified, stereo imagery from the CORONA and KEYHOLE satellite series enabled discovery of other examples in the K2 region. Comparison of mapped sackung failures with geologic base maps has demonstrated some coincidence of sackung with various structural trends, including synformal structures in upper thrust plates or along the traces of high-angle faults. In all probability these structural trends have provided plentiful ancillary planes of weakness along which gravitationally driven sackung is facilitated. Sackung failure in the Himalaya appears to be a spatially scale-dependent manifestation of a gravitational-collapse continuum of the brittle, upper crust, mainly involving mountain ridges. In contrast, gravitational collapse of the whole range may involve some similar failures but also include listric faulting, as well as subsidence movement into zones of ductility at depth. Temporal scale dependence of sackung may also be threshold dominated, wherein initial long-continued, slow failure ultimately leads to the commonly catastrophic rock-slope collapses recently recognized throughout the western Himalaya and now differentiated from their original mismapping as glacial moraines. Such sackung in Himalayan terrain undergoing active deglaciation from global warming may increase catastrophic slope-failure hazard.

Large-Scale Diversity of Slope Fishes: Pattern Inconsistency between Multiple Diversity Indices

PubMed Central

Gaertner, Jean-Claude; Colloca, Francesco; Politou, Chrissi-Yianna; Gil De Sola, Luis; Bertrand, Jacques A.; Murenu, Matteo; Durbec, Jean-Pierre; Kallianiotis, Argyris; Mannini, Alessandro

2013-01-01

Large-scale studies focused on the diversity of continental slope ecosystems are still rare, usually restricted to a limited number of diversity indices and mainly based on the empirical comparison of heterogeneous local data sets. In contrast, we investigate large-scale fish diversity on the basis of multiple diversity indices and using 1454 standardized trawl hauls collected throughout the upper and middle slope of the whole northern Mediterranean Sea (36°3′- 45°7′ N; 5°3′W - 28°E). We have analyzed (1) the empirical relationships between a set of 11 diversity indices in order to assess their degree of complementarity/redundancy and (2) the consistency of spatial patterns exhibited by each of the complementary groups of indices. Regarding species richness, our results contrasted both the traditional view based on the hump-shaped theory for bathymetric pattern and the commonly-admitted hypothesis of a large-scale decreasing trend correlated with a similar gradient of primary production in the Mediterranean Sea. More generally, we found that the components of slope fish diversity we analyzed did not always show a consistent pattern of distribution according either to depth or to spatial areas, suggesting that they are not driven by the same factors. These results, which stress the need to extend the number of indices traditionally considered in diversity monitoring networks, could provide a basis for rethinking not only the methodological approach used in monitoring systems, but also the definition of priority zones for protection. Finally, our results call into question the feasibility of properly investigating large-scale diversity patterns using a widespread approach in ecology, which is based on the compilation of pre-existing heterogeneous and disparate data sets, in particular when focusing on indices that are very sensitive to sampling design standardization, such as species richness. PMID:23843962

The morphology and evolution of the Stromboli 2002-2003 lava flow field--An example of a basaltic flow field emplaced on a steep slope

USGS Publications Warehouse

Lodato, Luigi; Harris, A.; Spampinato, L.; Calvari, Sonia; Dehn, J.; Patrick, M.

2007-01-01

The use of a hand-held thermal camera during the 2002–2003 Stromboli effusive eruption proved essential in tracking the development of flow field structures and in measuring related eruption parameters, such as the number of active vents and flow lengths. The steep underlying slope on which the flow field was emplaced resulted in a characteristic flow field morphology. This comprised a proximal shield, where flow stacking and inflation caused piling up of lava on the relatively flat ground of the vent zone, that fed a medial–distal lava flow field. This zone was characterized by the formation of lava tubes and tumuli forming a complex network of tumuli and flows linked by tubes. Most of the flow field was emplaced on extremely steep slopes and this had two effects. It caused flows to slide, as well as flow, and flow fronts to fail frequently, persistent flow front crumbling resulted in the production of an extensive debris field. Channel-fed flows were also characterized by development of excavated debris levees in this zone (Calvari et al. 2005). Collapse of lava flow fronts and inflation of the upper proximal lava shield made volume calculation very difficult. Comparison of the final field volume with that expecta by integrating the lava effusion rates through time suggests a loss of ~70% erupted lava by flow front crumbling and accumulation as debris flows below sea level. Derived relationships between effusion rate, flow length, and number of active vents showed systematic and correlated variations with time where spreading of volume between numerous flows caused an otherwise good correlation between effusion rate, flow length to break down. Observations collected during this eruption are useful in helping to understand lava flow processes on steep slopes, as well as in interpreting old lava–debris sequences found in other steep-sided volcanoes subject to effusive activity.

WHISPERS Project on the easternmost slope of the Ross Sea (Antarctica): preliminary results.

NASA Astrophysics Data System (ADS)

Olivo, E.; De Santis, L.; Bergamasco, A.; Colleoni, F.; Gales, J. A.; Florindo-Lopez, C.; Kim, S.; Kovacevic, V.; Rebesco, M.

2017-12-01

The advance and retreat of the West Antarctic Ice Sheet from the outer continental shelf and the oceanic circulation are the main causes of the depositional processes on the Ross Sea continental slope, at present time and during the most of the Cenozoic. Currently the Antarctic Bottom Water formation is directly linked to the relatively warm Circumpolar Deep Water that, encroaching the continental shelf, mixes with the colder Ross Sea Bottom Water. Detailed multibeam and geological surveys useful to locate and characterize peculiar morphological structures on the bottom are essential to study how the glacial and oceanographic processes interact with the seabed sediments. In the framework of the PNRA-WHISPERS project (XXXIIth Italian Antarctic expedition - January/March 2017), new multibeam bathymetric, sub-bottom chirp, were acquired from the easternmost margin of the Ross Sea, on the southeastern side of the Hayes Bank, usually covered by sea ice. We observed on the upper slope erosional features (incised gullies of likely glacial meltwater origin). A broad scar in the upper slope is characterized by an elongated SSW-NNE ridge (10 km long, 850-1200 m water depth, 2 km wide), that may be a remnants of previous glacial or debris flow deposits, eroded by meltwater outwash discharge at the beginning of grounding ice retreat and by RSBW cascading along the slope, as documented by Expandable Bathy-Thermograph and Acoustic Depth Current Profile data. Sub-bottom chirp profiles crossing this ridge show a very low amplitude reflective sea bed, supporting the hypothesis of its soft sediment nature, in good agreement with a very low acoustic velocity obtained by multichannel seismic data reprocessing. The occurrence of internal stratification on 2D multichannel seismic profiles would discount a gas-fluids related mud volcano origin. No sediment cores were collected, due to bad sea conditions and limited ship time, further data collection would be needed to fully understand the origin of such depositional feature and its relation with slope glacial and oceanographic processes.

Land degradation trends in upper catchments and morphological developments of braided rivers in drylands: the case of a marginal graben of the Ethiopian Rift Valley

NASA Astrophysics Data System (ADS)

Demissie, Biadgilgn; Frankl, Amaury; Haile, Mitiku; Nyssen, Jan

2014-05-01

Braided rivers have received relatively little attention in research and development activities in drylands. However, they strongly impact agroecology and agricultural activities and thereby local livelihoods. The Raya Graben (3750 km² including the escarpment) is a marginal graben of the Ethiopian Rift Valley located in North Ethiopia. In order to study the dynamics of braided rivers and the relationship with biophysical controls, 20 representative catchments were selected, ranging between 15 and 311 km². First, the 2005 morphology (length, area) of the braided rivers was related to biophysical controls (vegetation cover, catchment area and slope gradient in the steep upper catchments and gradient in the graben bottom). Second, the changes in length of the braided rivers were related to vegetation cover changes in the upper catchments since 1972. Landsat imagery was used to calculate the Normalized Difference Vegetation Index (NDVI), and to map vegetation cover and the total length of the braided rivers. Spot CNES imagery available from Google Earth was used to identify the total area of the braided rivers in 2005. A linear regression analysis revealed that the length of braided rivers was positively related to the catchment area (R²=0.32, p<0.01), but insignificantly related to vegetation cover in the upper catchments. However, there is an indication that it is an important factor in the relationship calculated for 2005 (R²=0.2, p=0.064). Similarly, the area occupied by the braided rivers was related to NDVI (R²=0.24, p<0.05) and upper catchment area (R²=0.447, p<0.01). Slope gradient is not an important explanatory factor. This is related to the fact that slope gradients are steep (average of 38.1%) in all upper and gentle (average of 3.4%) in graben bottom catchments. The vegetation cover in the upper catchments shows a statistically insignificant increasing trend (R²=0.73, p=0.067) over the last 40 years, whereas length of rivers in the graben bottom did not change significantly. This is due primarily to the stable vegetation cover conditions between the mid of 1980s and 2000 (average NDVI of 0.34 with std. deviation of 0.07). Vegetation cover and area of upper catchments are important controlling factors of the morphologic characteristics of braided rivers in drylands. Thus, measures geared towards reducing the impacts of braided rivers on agricultural systems and there by the livelihood of the society in plains need to focus on rehabilitation activities (soil and water conservation) in upper catchments.

Frosty Wind Streaks

NASA Technical Reports Server (NTRS)

2003-01-01

MGS MOC Release No. MOC2-532, 2 November 2003

As seasonal polar frosts sublime away each spring, winds may re-distribute some of the frost or move sediment exposed from beneath the frost. This action creates ephemeral wind streaks that can be used by scientists seeking to study the local circulation of the martian [missing text] surveyor (MGS) Mars Orbiter Camera (MOC) image shows a suite of wind streaks created in subliming carbon dioxide frost. These dark streaks appear to conform to the shape of the slopes on which they occur, suggesting that slope winds play a dominant role in creating and orienting these streaks. This picture is located near 73.8oS, 305.7oW. The image is illuminated by sunlight from the upper left and covers an area 3 km (1.9 mi) wide. Winds responsible for the streaks generally blew from the bottom/right (south/southeast) toward the top/upper left (north/northwest).

Deep-water fisheries at the Atlantic Frontier

NASA Astrophysics Data System (ADS)

Gordon, J. D. M.

2001-05-01

The deep sea is often thought of as a cold, dark and uniform environment with a low-fish biomass, much of which is highly adapted for life in a food-poor environment. While this might be true of the pelagic fish living in the water column, it is certainly not true of the demersal fish which live on or close to the bottom on the continental slopes around the British Isles (the Atlantic Frontier). These fish are currently being commercially exploited. There is growing evidence to support the view that success of the demersal fish assemblages depends on the pelagic or benthopelagic food sources that impinge both vertically and horizontally onto the slope. There are several quite separate and distinct deep-water fisheries on the Atlantic Frontier. It is a physical barrier, the Wyville-Thomson Ridge, which results in the most significant division of the fisheries. The Ridge, which has a minimum depth of about 500 m, separates the warmer deep Atlantic waters from the much colder Norwegian Sea water and as a result, the deep-water fisheries to the west of the Hebrides and around the offshore banks are quite different from those of the Faroe-Shetland Channel (West of Shetland). The fisheries to the West of the Hebrides can be further divided by the fishing method used into bottom trawl, semipelagic trawl and longline. The bottom-trawl fisheries extend from the shelf-slope break down to about 1700 m and the target species varies with depth. The smallest vessels in the fleet fish on the upper slope, where an important target species is the anglerfish or monkfish ( Lophius spp.). On the mid-slope the main target species are blue ling ( Molva dypterygia) and roundnose grenadier ( Coryphaenoides rupestris), with bycatches of black scabbardfish ( Aphanopus carbo) and deep-water sharks. On the lower slope orange roughy ( Hoplostethus atlanticus) is an important target species. The major semipelagic trawl fishery is a seasonal fishery on spawning aggregations of blue whiting ( Micromesistius poutassou). The other semipelagic fishery is on spawning aggregations of the greater silver smelt or argentine ( Argentina silus). Spanish and UK vessels that target mainly hake ( Merluccius merluccius) and a Norwegian fleet that targets ling ( Molva molva), blue ling and tusk ( Brosme brosme) dominate the upper slope longline fishery. West of Shetland, the fishery on the upper slope has some similarities with that of the Hebridean slope, with anglerfish and blue ling being important target species. A quite different fishery occurs in the transition zone between the Atlantic and Norwegian Sea waters. Here the main target species is Greenland halibut ( Reinhardtius hippoglossoides). Below the transition zone biomass decreases rapidly and there is no fishery. It is generally agreed that many deep-water species have slow growth, a high age at first maturity and a low fecundity, which makes them vulnerable to over-exploitation. Other features of these fishes such as high mortality of discards and escapees will add to the problems. Despite this the only management procedures in place are general limitation of effort measures within the area of jurisdiction of the European Union.

A Gulf Stream-derived pycnocline intrusion on the Middle Atlantic Bight shelf

NASA Astrophysics Data System (ADS)

Gawarkiewicz, Glen; McCarthy, Robert K.; Barton, Kenneth; Masse, Ann K.; Church, Thomas M.

1990-12-01

Saline intrusions from the upper slope onto the outer shelf are frequently observed at the pycnocline along the shelfbreak front in the Middle Atlantic Bight during the summer. A brief cruise was conducted in July, 1986 between Baltimore and Washington Canyons to examine along-shelf variability of pycnocline salinity intrusions. A particularly saline intrusion of 35.8 Practical Salinity Units (PSU) was observed between 20 and 40 m in a water depth of 70 to 80 m. The along-shelf extent was at least 40 km. The cooler, sub-pycnocline outer shelf water was displaced 15 km shoreward of the shelfbreak. A Gulf Stream filament was present in the slope region prior to the hydrographic sampling, but was not visible in thermal imagery during the hydrographic sampling. Temperature-salinity characteristics of the intrusion suggest that it was a mixture of Gulf Stream water and slope water, possibly from the filament. The shoreward penetration of saline water was most pronounced at the pycnocline and penetrated the shelfbreak front, with salinities as high as 35.0 PSU reaching as far shoreward as the 35 m isobath. These pycnocline intrusions may be an important mechanism for the transport of Gulf Stream-derived water onto the shelf during the summer. The presence of filaments or other Gulf Stream-derived water on the upper slope may account for some of the along-front variability of the pycnocline salinity maximum that has previously been observed.

Geomorphic process fingerprints in submarine canyons

USGS Publications Warehouse

Brothers, Daniel S.; ten Brink, Uri S.; Andrews, Brian D.; Chaytor, Jason D.; Twichell, David C.

2013-01-01

Submarine canyons are common features of continental margins worldwide. They are conduits that funnel vast quantities of sediment from the continents to the deep sea. Though it is known that submarine canyons form primarily from erosion induced by submarine sediment flows, we currently lack quantitative, empirically based expressions that describe the morphology of submarine canyon networks. Multibeam bathymetry data along the entire passive US Atlantic margin (USAM) and along the active central California margin near Monterey Bay provide an opportunity to examine the fine-scale morphology of 171 slope-sourced canyons. Log–log regression analyses of canyon thalweg gradient (S) versus up-canyon catchment area (A) are used to examine linkages between morphological domains and the generation and evolution of submarine sediment flows. For example, canyon reaches of the upper continental slope are characterized by steep, linear and/or convex longitudinal profiles, whereas reaches farther down canyon have distinctly concave longitudinal profiles. The transition between these geomorphic domains is inferred to represent the downslope transformation of debris flows into erosive, canyon-flushing turbidity flows. Over geologic timescales this process appears to leave behind a predictable geomorphic fingerprint that is dependent on the catchment area of the canyon head. Catchment area, in turn, may be a proxy for the volume of sediment released during geomorphically significant failures along the upper continental slope. Focused studies of slope-sourced submarine canyons may provide new insights into the relationships between fine-scale canyon morphology and down-canyon changes in sediment flow dynamics.

Faulting and instability of shelf sediments: eastern Gulf of Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, P.R.; Molnia, B.F.

1976-04-01

Faults and submarine slides or slumps are potential environmental hazards on the outer continental shelf of the northern Gulf of Alaska. Submarine slides or slumps have been found in two places in the OCS region: (1) seaward of the Malaspina Glacier and Icy Bay, an area of 1770 square kilometers, that has a slope of less than one-half degree, and (2) across the entire span of the Copper River prodelta, an area of 1730 square kilometers, that has a slope of about one-half degree. Seismic profiles across these areas show disrupted reflectors and irregular topography commonly associated with submarine slidesmore » or slumps. Other potential slide or slum areas have been delineated in areas of thick sediment accumulation and relatively steep slopes. These areas include Kayak Trough, parts of Hinchinbrook Entrance and Sea Valley, parts of the outer shelf and upper slope between Kayak Island and Yakutat Bay and Bering Trough.« less

Experimental test of theory for the stability of partially saturated vertical cut slopes

USGS Publications Warehouse

Morse, Michael M.; Lu, N.; Wayllace, Alexandra; Godt, Jonathan W.; Take, W.A.

2014-01-01

This paper extends Culmann's vertical-cut analysis to unsaturated soils. To test the extended theory, unsaturated sand was compacted to a uniform porosity and moisture content in a laboratory apparatus. A sliding door that extended the height of the free face of the slope was lowered until the vertical cut failed. Digital images of the slope cross section and upper surface were acquired concurrently. A recently developed particle image velocimetry (PIV) tool was used to quantify soil displacement. The PIV analysis showed strain localization at varying distances from the sliding door prior to failure. The areas of localized strain were coincident with the location of the slope crest after failure. Shear-strength and soil-water-characteristic parameters of the sand were independently tested for use in extended analyses of the vertical-cut stability and of the failure plane angle. Experimental failure heights were within 22.3% of the heights predicted using the extended theory.

Investigating Deep-Marine Sediment Waves in the Northern Gulf of Mexico Using 3D Seismic Data

NASA Astrophysics Data System (ADS)

Wang, Z.; Gani, M. R.

2016-12-01

Deep-water depositional elements have been studied for decades using outcrop, flume tank, sidescan sonar, and seismic data. Even though they have been well recognized by researchers, the improvements in the quality of 3D seismic data with increasingly larger dimension allow detailed analysis of deep-water depositional elements with new insights. This study focuses on the deep-marine sediment waves in the northern Gulf of Mexico. By interpreting a 3D seismic dataset covering 635 km2 at Mississippi Canyon and Viosca Knoll areas, large sediment waves, generated by sediment gravity flows, were mapped and analyzed with various seismic attributes. A succession of sediment waves, approximately 100 m in thickness, is observed on the marine slope that tapers out at the toe of the slope. The individual sediment wave exhibits up to 500 m in wavelength and up to 20 m in height. The wave crests oriented northeast-southwest are broadly aligned parallel to the regional slope-strike, indicating their sediment gravity flow origin. The crestlines are straight or slightly sinuous, with sinuosity increasing downslope. Their anti-dune patterns likely imply the presence of supercritical flows. The sediment waves have a retrogradational stacking pattern. Seismic amplitude maps of each sediment wave revealed that after depositing the majority of sheet-like sands on the upper slope, sediment gravity flows started to form large sediment waves on the lower slope. The steep and narrow upcurrent flanks of the sediment waves always display higher amplitudes than the gentle and wide downcurrent flanks, indicating that the sands were likely preferentially trapped along the upcurrent flanks, whereas the muds spread along the downcurrent flanks. The formation of sediment waves likely requires a moderate sand-mud ratio, as suggested by these observations: (1) absence of sediment waves on the upper slope where the sands were mainly deposited as unconfined sheets with a high sand-mud ratio; (2) absence of sediment waves on the basin floor, which is covered mainly by muds and hemipelagic sediments with a low sand-mud ratio; and (3) presence of sediment waves on the lower slope with a moderate sand-mud ratio.

Sediment movement and dispersal patterns on the Grand Banks continental shelf and slope were tied to the dynamics of the Laurentide ice-sheet margin

NASA Astrophysics Data System (ADS)

Rashid, H.; MacKillop, K.; Piper, D.; Vermooten, M.; Higgins, J.; Marche, B.; Langer, K.; Brockway, B.; Spicer, H. E.; Webb, M. D.; Fournier, E.

2015-12-01

The expansion and contraction of the late Pleistocene Laurentide ice-sheet (LIS) was the crucial determining factor for the geomorphic features and shelf and slope sediment mobility on the eastern Canadian continental margin, with abundant mass-transport deposits (MTDs) seaward of ice margins on the upper slope. Here, we report for the first time sediment failure and mass-transport deposits from the central Grand Banks slope in the Salar and Carson petroleum basins. High-resolution seismic profiles and multibeam bathymetry show numerous sediment failure scarps in 500-1600 m water depth. There is no evidence for an ice margin on the upper slope younger than MIS 6. Centimeter-scale X-ray fluorescence analysis (XRF), grain size, and oxygen isotope data from piston cores constrain sediment processes over the past 46 ka. Geotechnical measurements including Atterberg limit tests, vane shear measurements and triaxial and multi-stage isotropic consolidation tests allowed us to assess the instability on the continental margin. Cores with continuous undisturbed stratigraphy in contourite silty muds show normal downcore increase in bulk density and undrained peak shear strength. Heinrich (H) layers are identifiable by a marked increase in the bulk density, high Ca (ppm), increase in iceberg-rafted debris and lighter δ18O in the polar planktonic foram Neogloboquadrina pachyderma (sinistral): with a few C-14 dates they provide a robust chronology. There is no evidence for significant supply of sediment from the Grand Banks at the last-glacial maximum. Mass-transport deposits (MTD) are marked by variability in the bulk density, undrained shear strength and little variation in bulk density or Ca (ppm) values. The MTD are older than 46 ka on the central Grand Banks slope, whereas younger MTDs are present in southern Flemish Pass. Factor of safety calculations suggest the slope is statically stable up to gradients of 10°, but more intervals of silty mud may fail during earthquake-induced cyclic loading based on Atterberg tests. By analogy with the Holocene, contourites deposited in MIS 5e may be particularly silty and form a "weak layer" susceptible to failure.

Remote Sensing of Crosswind Profiles Using the Correlation Slope Method.

DTIC Science & Technology

1979-07-01

i s ‘What is the aeceptab it’ upper 1 int l t on ~ ~ca 11 i t 4 1 or w h i cli the i n v e r s i o n works in the noi seless case ?” In order to...ions in t h i s pape r . The b e h a v i o r of the pat h-we i g u t I ng fut te t i on W( • c i t s shoi ~t t iii I g . 2 t v a l u a t lOf l...1 Final Repsr~~ -~~ S. PV~~PO~ UWW O~~G; PORT NUMSEN • -S.--__ — - ~~. AUTHON(.) S. CONT R ACT ON GR ANT NUMSEN( . ) ,~ Ri~~~~ J~arakat/ Bolt

Marine forearc extension in the Hikurangi Margin: New insights from high-resolution 3D seismic data

NASA Astrophysics Data System (ADS)

Böttner, Christoph; Gross, Felix; Geersen, Jacob; Mountjoy, Joshu; Crutchley, Gareth; Krastel, Sebastian

2017-04-01

In subduction zones upper-plate normal faults have long been considered a tectonic feature primarily associated with erosive margins. However, increasing data coverage has proven that similar features also occur in accretionary margins, such as Cascadia, Makran, Nankai or Central Chile, where kinematics are dominated by compression. Considering their wide distribution there is, without doubt, a significant lack of qualitative and quantitative knowledge regarding the role and importance of normal faults and zones of extension for the seismotectonic evolution of accretionary margins. We use a high-resolution 3D P-Cable seismic volume from the Hikurangi Margin acquired in 2014 to analyze the spatial distribution and mechanisms of upper-plate normal faulting. The study area is located at the upper continental slope in the area of the Tuaheni landslide complex. In detail we aim to (1) map the spatial distribution of normal faults and characterize their vertical throws, strike directions, and dip angles; (2) investigate their possible influence on fluid migration in an area, where gas hydrates are present; (3) discuss the mechanisms that may cause extension of the upper-slope in the study area. Beneath the Tuaheni Landslide Complex we mapped about 200 normal faults. All faults have low displacements (<15 m) and dip at high (> 65°) angles. About 71% of the faults dip landward. We found two main strike directions, with the majority of faults striking 350-10°, parallel to the deformation front. A second group of faults strikes 40-60°. The faults crosscut the BSR, which indicates the base of the gas hydrate zone. In combination with seismically imaged bright-spots and pull-up structures, this indicates that the normal faults effectively transport fluids vertically across the base of the gas hydrate zone. Localized uplift, as indicated by the presence of the Tuaheni Ridge, might support normal faulting in the study area. In addition, different subduction rates across the margin may also favor extension between the segments. Future work will help to further untangle the mechanisms that cause extension of the upper continental slope.

Preliminary Results from Acoustic Survey Offshore Kefken, Southwestern Black Sea Margin

NASA Astrophysics Data System (ADS)

Dondurur, Derman; Karaca, Onur; Nasıf, Aslıhan

2017-04-01

In March 2016, different marine acoustic datasets were collected aboard of R/V K. Piri Reis research vessel of Dokuz Eylül University within the scope of Turkish Research Council (Tübitak) Project (115Y218) to reveal submarine morphology and seismo-acoustical structure of the continental shelf and upper slope of Şile-Kefken region in the southwest of the Black Sea. A total of 1564 km high resolution seismic, multibeam bathymetry and Chirp sub-bottom profiler data were collected. Seismic data was collected using a 1500 m long digital streamer with 240 active channels. Group and shot intervals were 6.25 m and 25 m, respectively. Collected data were analyzed by means of (i) stratigraphic and (ii) structural components, and (iii) the structure of upper slope and shelf break. The stratigraphic elements in the region indicate the existence of Eocene and younger units. A distinctive acoustical basement in the seismic data observed throughout the shelf which is interpreted as uplifted Cretaceous basement of the Black Sea, that is Akveren or Yemişliçay Formation. The basement also outcrops around the Kefken Island. Chirp data is used to map the shallow stratigraphy of the shelf including the Holocene sediment distribution which exists on a very restricted area on the shelf. To the east, there is a large outcrop zone offshore Kefken where no Holocene sediments are observed. Initial evaluation of the collected data indicates that there is no present day delta formation in the area due to a few weak streams observed in the study area. The penetration of Chirp data in the western and the southern parts of the shelf area is very limited while it increases towards to upper continental slope to the North, and east of Kefken Cape. The acoustic data suggests that the study area is under the influence of the Pontide overthrust. Possible existence of reverse faults of Pontide overthrust is evident on the seismic data from southwestern shelf. In addition to the reverse faults to the SW, the whole shelf is highly affected by a northwards trending strike slip fault system with a significant vertical slip. Canyon heads and shelf break is deformed by numerous near vertical normal faults. Multibeam bathymetric data indicate that the upper slope is formed by highly steep canyon heads with several small scale gullies connecting to the thalweg at low angles.

A Theoretical Study of Cold Air Damming.

NASA Astrophysics Data System (ADS)

Xu, Qin

1990-12-01

The dynamics of cold air damming are examined analytically with a two-layer steady state model. The upper layer is a warm and saturated cross-mountain (easterly or southeasterly onshore) flow. The lower layer is a cold mountain-parallel (northerly) jet trapped on the windward (eastern) side of the mountain. The interface between the two layers represents a coastal front-a sloping inversion layer coupling the trapped cold dome with the warm onshore flow above through pressure continuity.An analytical expression is obtained for the inviscid upper-layer flow with hydrostatic and moist adiabatic approximations. Blackadar's PBL parameterization of eddy viscosity is used in the lower-layer equations. Solutions for the mountain-parallel jet and its associated secondary transverse circulation are obtained by expanding asymptotically upon a small parameter proportional to the square root of the inertial aspect ratio-the ratio between the mountain height and the radius of inertial oscillation. The geometric shape of the sloping interface is solved numerically from a differential-integral equation derived from the pressure continuity condition imposed at the interface.The observed flow structures and force balances of cold air damming events are produced qualitatively by the model. In the cold dome the mountain-parallel jet is controlled by the competition between the mountain-parallel pressure gradient and friction: the jet is stronger with smoother surfaces, higher mountains, and faster mountain-normal geostrophic winds. In the mountain-normal direction the vertically averaged force balance in the cold dome is nearly geostrophic and controls the geometric shape of the cold dome. The basic mountain-normal pressure gradient generated in the cold dome by the negative buoyancy distribution tends to flatten the sloping interface and expand the cold dome upstream against the mountain-normal pressure gradient (produced by the upper-layer onshore wind) and Coriolis force (induced by the lower-layer mountain-parallel jet). It is found that the interface slope increases and the cold dome shrinks as the Froude number and/or upstream mountain-parallel geostrophic wind increase, or as the Rossby number, upper-layer depth, and/or surface roughness length decrease, and vice versa. The cold dome will either vanish or not be in a steady state if the Froude number is large enough or the roughness length gets too small. The theoretical findings are explained physically based on detailed analyses of the force balance along the inversion interface.

Earth Observation taken during the Expedition 37 mission

NASA Image and Video Library

2013-09-30

ISS037-E-005089 (30 Sept. 2013) --- Ruapehu volcano and Tongariro volcanic complex in New Zealand are featured in this image photographed by an Expedition 37 crew member on the International Space Station. Mount Ruapehu is one of several volcanic centers on the North Island of New Zealand, but is the largest and historically most active. The 2,797-meter elevation volcano is also the highest mountain on North Island and is covered with snow on its upper slopes. Scientists believe while there are three summit craters that have been active during the last 10,000 years, South Crater is the only historically active one. This vent is currently filled with a lake (Crater Lake), visible at left; eruptions from the vent, mixed with water from the lake can lead to the formation of lahars – destructive gravity flows of mixed fluid and volcanic debris that form a hazard to ski areas on the upper slopes and lower river valleys. The most recent significant eruption of Ruapehu took place in 2007 and formed both an eruption plume and lahars. The volcano is surrounded by a 100-cubic-kilometer ring plain of volcaniclastic debris that appears dark grey in the image, whereas vegetated areas appear light to dark green. Located to the northeast of the Ruapehu volcanic structure, the Tongariro volcanic complex (lower right) is currently in an active eruptive phase – the previous eruptive phase ended in 1897. Explosive eruptions occurred in 2012, which have been followed by steam and gas plumes observed almost daily. According to scientists, the volcanic complex contains multiple cones constructed over the past 275,000 years. The most prominent of these, Mount Ngauruhoe, last erupted in 1975. Like Ruapehu, the upper slopes of both Ngauruhoe and the upper peaks of Tongariro are snow-covered. Scattered cloud cover is also visible near Tongariro at lower right.

Effect of Balloon Pulmonary Angioplasty on Respiratory Function in Patients With Chronic Thromboembolic Pulmonary Hypertension.

PubMed

Akizuki, Mina; Serizawa, Naoki; Ueno, Atsuko; Adachi, Taku; Hagiwara, Nobuhisa

2017-03-01

Balloon pulmonary angioplasty (BPA) in chronic thromboembolic pulmonary hypertension (CTEPH) improves hemodynamics and exercise capacity. However, its effect on respiratory function is unclear. Our objective was to investigate the effect of BPA on respiratory function. We enrolled patients with inoperable CTEPH who underwent BPA primarily in lower lobe arteries (first series) and upper and middle lobe arteries (second series). We compared changes in hemodynamics and respiratory function between different BPA fields. Sixty-two BPA sessions were performed in 13 consecutive patients. Mean pulmonary arterial pressure and pulmonary vascular resistance significantly improved from 44 ± 8 to 23 ± 5 mm Hg and 818 ± 383 to 311 ± 117 dyne/s/cm -5 . The percent predicted diffusion capacity of lung for carbon monoxide (Dlco) decreased after BPA in the lower lung field (from 60% ± 8% to 54% ± 8%) with no recovery. Percent Dlco increased after BPA in the upper middle lung field (from 53% ± 6% to 58% ± 6%) and continued to improve during the follow-up (from 58% ± 6% to 64% ± 11%). The ventilation/Co 2 production (V˙e/V˙co 2 ) slope significantly improved after BPA in the lower lung field (from 51 ± 13 to 41 ± 8) and continued to improve during the follow-up (from 41 ± 8 to 35 ± 7); however, the V˙e/V˙co 2 slope remained unchanged after BPA in the upper/middle lung field. Changes in % Dlco and the V˙e/V˙co 2 slope differed significantly between lower and upper/middle lung fields. The effect of BPA on respiratory function in patients with CTEPH differed depending on the lung field. Copyright © 2016 American College of Chest Physicians. Published by Elsevier Inc. All rights reserved.

Geochemistry of host rocks in the Howards Pass district, Yukon-Northwest Territories, Canada: implications for sedimentary environments of Zn-Pb and phosphate mineralization

USGS Publications Warehouse

Slack, John F.; Falck, Hendrik; Kelley, Karen D.; Xue, Gabriel G.

2017-01-01

Detailed lithogeochemical data are reported here on early Paleozoic sedimentary rocks that host the large Howards Pass stratiform Zn-Pb deposits in Yukon-Northwest Territories. Redox-sensitive trace elements (Mo, Re, V, U) and Ce anomalies in members of the Duo Lake Formation record significant environmental changes. During the deposition of lower footwall units (Pyritic siliceous and Calcareous mudstone members), bottom waters were anoxic and sulphidic, respectively; these members formed in a marginal basin that may have become increasingly restricted with time. Relative to lower members, a major environmental change is proposed for deposition of the overlying Lower cherty mudstone member, which contains phosphorite beds up to ∼0.8 m thick in the upper part, near the base of the Zn-Pb deposits. The presence of these beds, together with models for modern phosphorite formation, suggests P input from an upwelling system and phosphorite deposition in an upper slope or outer shelf setting. The overlying Active mudstone member contains stratabound to stratiform Zn-Pb deposits within black mudstone and gray calcareous mudstone. Data for unmineralized black mudstone in this member indicate deposition under diverse redox conditions from suboxic to sulphidic. Especially distinctive in this member are uniformly low ratios of light to heavy rare earth elements that are unique within the Duo Lake Formation, attributed here to the dissolution of sedimentary apatite by downward-percolating acidic metalliferous brines. Strata that overlie the Active member (Upper siliceous mudstone member) consist mainly of black mudstone with thin (0.5–1.5 cm) laminae of fine-grained apatite, recording continued deposition on an upper slope or outer shelf under predominantly suboxic bottom waters. Results of this study suggest that exploration for similar stratiform sediment-hosted Zn-Pb deposits should include the outer parts of ancient continental margins, especially at and near stratigraphic transitions from marginal basin facies to overlying slope or shelf facies.

Conceptual model of sediment processes in the upper Yuba River watershed, Sierra Nevada, CA

USGS Publications Warehouse

Curtis, J.A.; Flint, L.E.; Alpers, Charles N.; Yarnell, S.M.

2005-01-01

This study examines the development of a conceptual model of sediment processes in the upper Yuba River watershed; and we hypothesize how components of the conceptual model may be spatially distributed using a geographical information system (GIS). The conceptual model illustrates key processes controlling sediment dynamics in the upper Yuba River watershed and was tested and revised using field measurements, aerial photography, and low elevation videography. Field reconnaissance included mass wasting and channel storage inventories, assessment of annual channel change in upland tributaries, and evaluation of the relative importance of sediment sources and transport processes. Hillslope erosion rates throughout the study area are relatively low when compared to more rapidly eroding landscapes such as the Pacific Northwest and notable hillslope sediment sources include highly erodible andesitic mudflows, serpentinized ultramafics, and unvegetated hydraulic mine pits. Mass wasting dominates surface erosion on the hillslopes; however, erosion of stored channel sediment is the primary contributor to annual sediment yield. We used GIS to spatially distribute the components of the conceptual model and created hillslope erosion potential and channel storage models. The GIS models exemplify the conceptual model in that landscapes with low potential evapotranspiration, sparse vegetation, steep slopes, erodible geology and soils, and high road densities display the greatest hillslope erosion potential and channel storage increases with increasing stream order. In-channel storage in upland tributaries impacted by hydraulic mining is an exception. Reworking of stored hydraulic mining sediment in low-order tributaries continues to elevate upper Yuba River sediment yields. Finally, we propose that spatially distributing the components of a conceptual model in a GIS framework provides a guide for developing more detailed sediment budgets or numerical models making it an inexpensive way to develop a roadmap for understanding sediment dynamics at a watershed scale.

Intrusions of Kuroshio and Shelf Waters on Northern Slope of South China Sea in Summer 2015

NASA Astrophysics Data System (ADS)

Li, Denghui; Zhou, Meng; Zhang, Zhaoru; Zhong, Yisen; Zhu, Yiwu; Yang, Chenghao; Xu, Mingquan; Xu, Dongfeng; Hu, Ziyuan

2018-06-01

The northern slope region of the South China Sea (SCS) is a biological hot spot characterized by high primary productivity and biomasses transported by cross-shelf currents, which support the spawning and growth of commercially and ecologically important fish species. To understand the physical and biogeochemical processes that promote the high primary production of this region, we conducted a cruise from June 10 and July 2, 2015. In this study, we used fuzzy cluster analysis and optimum multiparameter analysis methods to analyze the hydrographic data collected during the cruise to determine the compositions of the upper 55-m water masses on the SCS northern slope and thereby elucidate the cross-slope transport of shelf water (SHW) and the intrusions of Kuroshio water (KW). We also analyzed the geostrophic currents derived from acoustic Doppler current profiler measurements and satellite data. The results reveal the surface waters on the northern slope of the SCS to be primarily composed of waters originating from South China Sea water (SCSW), KW, and SHW. The SCSW dominated a majority of the study region at percentages ranging between 60% and 100%. We found a strong cross-slope current with speeds greater than 50 cm s-1 to have carried SHW into and through the surveyed slope area, and KW to have intruded onto the slope via mesoscale eddies, thereby dominating the southwestern section of the study area.

Map showing coastal cliff retreat rates along the Big Sur coast, Monterey and San Luis Obispo Counties, California

USGS Publications Warehouse

Hapke, Cheryl J.; Green, Krystal R.

2004-01-01

The average coastal cliff retreat rate along the Big Sur coast is 18 ? 6 cm/yr as measured over a 52-year time period. The erosion reference features measured as the cliff edge include the well-defined cliff edges common to marine terraces, slight breaks in the slope defining the upper edge of the active lower slope, and the road grade. Cliff erosion and retreat are focused in isolated erosion hotspots that account for most of the calculated average retreat.

Erosion of the Edge of the South Polar Layered Deposits

NASA Image and Video Library

2017-05-22

This image is an oblique view from NASA's Mars Reconnaissance Orbiter of the sloping edge of the stack of icy layers over the South Pole has some interesting morphologies. The slope appears to be eroding from a combination of landslides, block falls, and sublimation. The bright icy exposure in the larger landslide scar (upper right) suggests that this was a relatively recent event. Small-scale textures over the scene are due to both blowing wind and the thermal expansion and contraction of shallow ice. https://photojournal.jpl.nasa.gov/catalog/PIA21637

Constraining the Surficial Liquid Water and Resulting Atmospheric Water Vapor Abundance at Recurring Slope Lineae (RSL) Locations on Mars

NASA Astrophysics Data System (ADS)

Berdis, Jodi; Murphy, Jim; Wilson, Robert John

2017-10-01

Possible signatures of atmospheric water vapor arising from Martian Recurring Slope Lineae (RSLs) are investigated in this study. RSLs appear during local spring and summer on downward, equator-facing slopes at southern mid-latitudes (~31-52°S Stillman et al. 2014), and have been linked to liquid water which leaves behind streaks of briny material (McEwen et al. 2011, McEwen et al. 2014). Viking Orbiter Mars Atmospheric Water Detector (VO MAWD) and Mars Global Surveyor Thermal Emission Spectrometer (MGS TES) derived atmospheric water vapor abundance values are interrogated to determine whether four RSL locations at southern mid-latitudes (Palikir Crater, Hale Crater, Horowitz Crater, Coprates Chasma) exhibit episodic, enhanced local atmospheric water vapor abundance during southern spring and summer (Ls = 180-360°) when RSLs are observed to develop (Stillman et al. 2014, Ojha et al. 2015). Significant water vapor signals at these locations might reveal RSLs as the source of the enhanced water vapor. Detected atmospheric water vapor signals would expand upon current knowledge of RSLs, whereas non-detection could provide upper limits on RSL water source content. In order to assess how much surficial RSL water would be required to produce a detectable signal, we utilize the high spatial resolution Geophysical Fluid Dynamics Laboratory Mars Climate General Circulation Model to simulate the evaporation of RSL-producing surface water and quantify the magnitude and temporal duration of water vapor content that might be anticipated in response to inferred RSL surface water release. Finally, we will assess the ability of past and future orbiter-based instruments to detect such water vapor quantities.

Relict Landscape Response to Knickpoint Migration on the Roan Plateau, Western Colorado, Explored Through ALSM Data Analysis

NASA Astrophysics Data System (ADS)

Berlin, M. M.; Anderson, R. S.

2007-12-01

The unprecedented spatial resolution of Digital Elevation Models (DEMs) derived from Airborne Laser Swath Mapping (ALSM) makes them ideal for detecting subtle morphologic features. We explore to what extent information about knickpoint migration is communicated upstream by analyzing an ASLM-derived DEM in a transient landscape. We target the Roan Plateau in western Colorado, a landscape developed in flat-lying Eocene shales, in which multiple upstream-migrating waterfalls triggered by base level fall have incised dramatic canyons in their wake. The waterfalls separate low-gradient, bedrock-floored reaches above the waterfalls from steep, boulder-choked canyons below. Similarly, a sheer canyon rim separates a smooth, relict landscape above the canyon walls from the steep cliffs and talus-mantled slopes below. Waterfall and canyon rim elevations correlate well with the outcrop of a resistant oil-shale layer. We use a 1-meter DEM to develop two simple metrics that detect channel and hillslope response of the upper landscape to knickpoint migration. The first metric is stream profile analysis of upper plateau tributaries. In a steady-state stream channel, slope should decrease with distance downstream, as drainage area and the associated water discharge increase. Departures from this trend can be attributed to either lithologic variation, or transient oversteepening that may be associated with the presence of the waterfall. Oversteepening of the channel can incite hillslope response, and give rise to a box canyon upstream of the waterfall. We document the slope of channels as they approach the free overfall, and the presence and lengths of box canyons upstream of the waterfall lip. The second metric is the curvature of plateau hilltops. In a steady state landscape, hilltops should be roughly parabolic in cross-section, reflecting a balance between a uniform rate of regolith production and diffusive transport at all points along the hillslope. Departure from this parabolic form can reflect lithologic variation, transient hillslope response to increased rates of stream incision, or transport processes that are not linearly dependent on slope. Isolation of roughly the upper 100 m of hilltops and evaluation of the curvature of these crests provides constraint on the ratio of weathering rate to transport efficiency in the landscape most likely to be in steady state. Changes in crest curvature with distance from the canyon rim can be used to document transient hillslope response of the upper plateau surface in areas with uniform lithology. Paired with field observations and mapped bedrock contacts, analysis of an ASLM-derived DEM allows us to evaluate the extent to which the upper plateau channels and hillslopes have responded to knickpoint migration and the carving of canyons downstream. Morphologic evidence for significant upper plateau response to this incision event would suggest that the timescale for landscape adjustment to base level fall may be shorter than that required to propagate a knickpoint upstream.

Volcano collapse promoted by hydrothermal alteration and edifice shape, Mount Rainier, Washington

USGS Publications Warehouse

Reid, M.E.; Sisson, T.W.; Brien, D.L.

2001-01-01

Catastrophic collapses of steep volcano flanks threaten many populated regions, and understanding factors that promote collapse could save lives and property. Large collapses of hydrothermally altered parts of Mount Rainier have generated far-traveled debris flows; future flows would threaten densely populated parts of the Puget Sound region. We evaluate edifice collapse hazards at Mount Rainier using a new three-dimensional slope stability method incorporating detailed geologic mapping and subsurface geophysical imaging to determine distributions of strong (fresh) and weak (altered) rock. Quantitative three-dimensional slope stability calculations reveal that sizeable flank collapse (>0.1 km3) is promoted by voluminous, weak, hydrothermally altered rock situated high on steep slopes. These conditions exist only on Mount Rainier's upper west slope, consistent with the Holocene debris-flow history. Widespread alteration on lower flanks or concealed in regions of gentle slope high on the edifice does not greatly facilitate collapse. Our quantitative stability assessment method can also provide useful hazard predictions using reconnaissance geologic information and is a potentially rapid and inexpensive new tool for aiding volcano hazard assessments.

Depositional sequences and facies in the Torok Formation, National Petroleum Reserve, Alaska (NPRA)

USGS Publications Warehouse

Houseknecht, David W.; Schenk, Christopher J.

2002-01-01

Brookian turbidites (Cretaceous through Tertiary) have become oil exploration objectives on the NorthSlope of Alaska during the past decade, and it is likely this focus will extend into the National Petroleum Reserve-Alaska (NPRA). A regional grid of 2-D seismic data, sparse well control, and field work in the Brooks Range foothills provide constraints for an ongoing effort to establish a sequence stratigraphic framework for Brookian turbidites in the Torok Formation across NPRA. The Torok Formation and overlying Nanushuk Formation (both mostly Albian) display the overall seismic geometry of bottomset-clinoform-topset strata indicating northeastward migration of a shelf margin. Within bottomset and clinoform strata of the Torok, depositional sequences have been identified that represent four distinct phases of shelf-margin sedimentation. (1) Regression, representing low relative sea level, is characterized by the development of an erosional surface on the shelf and upper slope, and the deposition of turbidite channel deposits on the middle to lower slope and submarine fan deposits at the base of slope. These deposits constitute a lowstand systems tract (LST). (2) Transgression, representing rising relative sea level, is characterized by the deposition of a mudstone drape on the basin floor, slope, and outer shelf. This drape comprises relatively condensed facies that constitute a transgressive systems tract (TST). (3) Aggradation, representing high relative sea level, is characterized by the deposition of relatively thick strata on the outer shelf and moderately thick mudstones on the slope. (4) Progradation, also representing high relative sea level, is characterized by the deposition of relatively thin strata on the outer shelf and very thick mudstones on the slope. Together, deposits of the aggradation and progradation phases constitute a highstand systems tract (HST). Large scale geometries of Torok strata vary across the Colville basin. In southern NPRA, high rates of subsidence accommodated the deposition of a "foredeep clinoform wedge" that contains a high proportion of sand-rich LST deposits. In northern NPRA, lower rates of subsidence favored the accumulation of mud-rich HST deposits. The most favorable stratigraphic trapping geometries in the Torok Formation occur where amalgamated sandstones deposited in turbidite channels incised on the mid- to lower-slope and on the proximal parts of submarine fans during regression (LSTs) are capped by relatively condensed mudstone facies deposited during transgression (TSTs). Common successions observed in Torok cores include a spectrum of slope and turbidite facies. Upper slope facies comprise laminated mudstones and siltstones that locally display evidence of slumping, sliding, and chaotic failure. Lower slope facies comprise heterolithic turbidites at some locations and interlaminated mudstones and thin, very fine-grained sandstones at others. Torok turbidites include amalgamated sandstones deposited in channel systems as well as thin-bedded, widespread sandstones deposited by unconfined flows on lobes or in channel overbank settings. These turbidite facies likely occur in both channel-lobe systems and slope apron systems within the Torok.

Regional scale estimates of baseflow and factors influencing baseflow in the Upper Colorado River Basin

USGS Publications Warehouse

Rumsey, Christine; Miller, Matthew P.; Susong, David D.; Tillman, Fred D.; Anning, David W.

2015-01-01

Results suggest that approximately half of the streamflow in the UCRB is baseflow derived from groundwater discharge to streams. Higher baseflow yields typically occur in upper elevation areas of the UCRB. PCA identified precipitation, snow, sand content of soils, elevation, land surface slope, percent grasslands, and percent natural barren lands as being positively correlated with baseflow yield; whereas temperature, potential evapotranspiration, silt and clay content of soils, percent agriculture, and percent shrublands were negatively correlated with baseflow yield.

Distortion of Magnetic Fields in a Starless Core. III. Polarization–Extinction Relationship in FeSt 1-457

NASA Astrophysics Data System (ADS)

Kandori, Ryo; Tamura, Motohide; Nagata, Tetsuya; Tomisaka, Kohji; Kusakabe, Nobuhiko; Nakajima, Yasushi; Kwon, Jungmi; Nagayama, Takahiro; Tatematsu, Ken’ichi

2018-04-01

The relationship between dust polarization and extinction was determined for the cold dense starless molecular cloud core FeSt 1-457 based on the background star polarimetry of dichroic extinction at near-infrared wavelengths. Owing to the known (three-dimensional) magnetic field structure, the observed polarizations from the core were corrected by considering (a) the subtraction of the ambient polarization component, (b) the depolarization effect of inclined distorted magnetic fields, and (c) the magnetic inclination angle of the core. After these corrections, a linear relationship between polarization and extinction was obtained for the core in the range up to A V ≈ 20 mag. The initial polarization versus extinction diagram changed dramatically after the corrections of (a) to (c), with the correlation coefficient being refined from 0.71 to 0.79. These corrections should affect the theoretical interpretation of the observational data. The slope of the finally obtained polarization–extinction relationship is {P}H/{E}H-{Ks}=11.00+/- 0.72 % {mag}}-1, which is close to the statistically estimated upper limit of the interstellar polarization efficiency. This consistency suggests that the upper limit of interstellar polarization efficiency might be determined by the observational viewing angle toward polarized astronomical objects.

The distribution of particulate material on Mars

NASA Technical Reports Server (NTRS)

Christensen, Philip R.

1991-01-01

The surface materials on Mars were extensively studied using a variety of spacecraft and Earth-based remote sensing observations. These measurements include: (1) diurnal thermal measurements, used to determine average particle size, rock abundance, and the presence of crusts; (2) radar observations, used to estimate the surface slope distributions, wavelength scale roughness, and density; (3) radio emission observations, used to estimate subsurface density; (4) broadband albedo measurements, used to study the time variation of surface brightness and dust deposition and removal; and (5) color observations, used to infer composition, mixing, and the presence of crusts. Remote sensing observations generally require some degree of modeling to interpret, making them more difficult to interpret than direct observations from the surface. They do, however, provide a means for examining the surface properties over the entire planet and a means of sampling varying depths within the regolith. Albedo and color observations only indicate the properties of the upper-most few microns, but are very sensitive to thin, sometimes emphemeral dust coatings. Thermal observations sample the upper skin depth, generally 2 to 10 cm. Rock abundance measurements give an indirect indication of surface mantling, where the absence of rocks suggests mantles of several meters. Finally, radar and radio emission data can penetrate several meters into the surface, providing an estimate of subsurface density and roughness.

Stability model and risk assessment for the Montescaglioso Landslide (Southern Italy)

NASA Astrophysics Data System (ADS)

Amanti, Marco; Chiessi, Vittorio; Guarino, Paolo Maria; Spizzichino, Daniele; Troccoli, Alessandro; Vizzini, Giorgio

2015-04-01

In this paper, we present the final results of a landslide risk assessment evaluation implemented for the recent Montescaglioso landslide emergency occurred on 3rd December 2013 when a large and rapid slope failure, triggered by prolonged and intense rainfall, affected a big portion of the SW slope of the village. The slope failure damaged a main road, private homes and commercial buildings. The Montescaglioso village (Basilicata Region, Italy) is located on the top of a conglomerate hill overlying a gentle slope constituted by Plio-Pleistocene clays. The area has been affected since ancient time by different landslide typologies and mechanism, as determined by a direct geomorphological survey and from mapping and available technical literature. Phenomena such as rock-falls and rock lateral spreading in the upper part of the hill, and rotational/translational slides and earth flows can be recognized in the area. Landslides are mainly promoted by the geological and structural setting of the area as well as by very low mechanical characteristics of sediments outcropping in the area. After the emergency phase, a detailed program of field survey and laboratory campaign has been implemented during the last year. A detailed topographical analysis has been developed by using the LIDAR survey in order to define morphometric conditions and geometry modifications of the slope affected by the landslide. Based on the studies carried out in the area, the research has been aimed to assessing the stability conditions (residual landslide risk) of the SW slope of the hill trough an extended geological, geomorphological and geotechnical campaign linked with numerical study of present instability mechanism. The geological and geotechnical model of the slope has been defined trough the analysis of the past and recent logs obtained from several boreholes and also through the results of many mechanical test performed on samples taken in the area. The numerical study has been carried out using two different commercial codes, the Differences Elements Flac ® and Finite Elements Phase2® in 2-Dimensional plain strain conditions, applied to a typical section extending along the slope. The geotechnical model has been calibrated trough a back analysis procedure of the December 2013 failure event. By adopting a reasonable hypothesis concerning the hydraulic conditions in the slope, this procedure allowed to reduce the mechanical parameter obtained during the geotechnical laboratory characterizations to the site scale. The numerical results stressed the influence of a pre existing deep potential failure surface able to trigger a phenomenon of the investigated magnitude. Monitoring data, which are currently in elaboration, are expected to integrate and enhance the understanding of instability mechanism affecting the Montescaglioso village. The reconstruction and modeling of the landslide evolution can be useful to suggest correct mitigation strategies that may help to prevent social and economic degradation of the territory

Geologic map of the La Mesita Negra SE Quadrangle, Bernalillo County, New Mexico

USGS Publications Warehouse

Shroba, Ralph R.; Thompson, Ren A.; Schmidt, Dwight L.; Personius, Stephen F.; Maldonado, Florian; Brandt, Theodore R.

2003-01-01

Geologic mapping, in support of the USGS Middle Rio Grande Basin Geologic Mapping Project, shows the spatial distribution of artificial-fill, alluvial, colluvial, and eolian deposits, lava flows and related sediments of the Albuquerque volcanoes, and upper Santa Fe Group sediments. These deposits are on, beneath, and along the West Mesa (Llano de Albuquerque) just west of Albuquerque, New Mexico. Artificial fill deposits are mapped chiefly beneath and near segments of Interstate 40, in an inactive landfill (or dump) north of Interstate 40 near the eastern boundary of the map area, and in the active Cerro Colorado landfill near the southwestern corner of the map area. Alluvial deposits are mapped in stream channels, beneath treads of terraces, and on hill slopes. They include alluvium in stream channels and beneath treads of low terraces, terrace alluvium, sheetwash deposits, gravelly alluvium, and old alluvium and calcic soils of the Llano de Albuquerque. Alluvial and colluvial deposits are mapped on hill slopes. They include young alluvial-slope deposits, alluvium and colluvium, undivided, and old alluvial-slope deposits. Colluvial deposits are also mapped on hill slopes. They include colluvial deposits, undivided, as well as alluvial deposits, eolian sand, and calcic soils associated with fault scarps. Eolian deposits as well as eolian and alluvial deposits mantle gently slopping surfaces on the Llano de Albuquerque. They include active eolian sand, active and inactive eolian sand and sheetwash deposits, undivided, and inactive eolian sand and sheetwash deposits, undivided. Lava flows and related sediments of the Albuquerque volcanoes were mapped near the southeast corner of the map area. They include five young lava flows, two young cinder deposits, and old lava flows. Upper Santa Fe Group sediments are well exposed and mapped in the western part of the map area. They include a gravel unit, a pebbly sand unit, and a mud and sand unit. Undivided upper Santa Fe Group sediments were mapped in the eastern part of the map area. Sediments and lava flows in the map area record alluvial, eolian, colluvial, and volcanic processes of the past several million years. The surficial deposits (post-Santa Fe Group sediments) on the map are known or estimated to be at least 1 m thick; most deposits are poorly exposed. Thin (< 50 cm), discontinuous deposits of eolian sand and sheetwash (Qea, Qes, and Qsw) locally are present on gently sloping map units older than the alluvium in stream channels and low terraces (Qa). These thin eolian and sheetwash deposits are not mapped, but they are widespread on the gravel unit of the upper Santa Fe Group sediments (Tg) on the eastern flank of the Llano de Albuquerque, near the eastern boundary of the map area (quadrangle). Small deposits of artificial fill (af) less than about 25 m wide are not mapped. Fractional map symbols (for example, Qsw/Qby1) are used where sheetwash deposits mantle lava flows. These fractional units are not described here; instead refer to descriptions of individual units.

Medicaid program; revision to Medicaid upper payment limit requirements for hospital services, nursing facility services, intermediate care facility services for the mentally retarded, and clinic services. Health Care Financing Administration (HCFA), HHS. Final rule.

PubMed

2001-01-12

This final rule modifies the Medicaid upper payment limits for inpatient hospital services, outpatient hospital services, nursing facility services, intermediate care facility services for the mentally retarded, and clinic services. For each type of Medicaid inpatient service, existing regulations place an upper limit on overall aggregate payments to all facilities and a separate aggregate upper limit on payments made to State-operated facilities. This final rule establishes an aggregate upper limit that applies to payments made to government facilities that are not State government-owned or operated, and a separate aggregate upper limit on payments made to privately-owned and operated facilities. This rule also eliminates the overall aggregate upper limit that had applied to these services. With respect to outpatient hospital and clinic services, this final rule establishes an aggregate upper limit on payments made to State government-owned or operated facilities, an aggregate upper limit on payments made to government facilities that are not State government-owned or operated, and an aggregate upper limit on payments made to privately-owned and operated facilities. These separate upper limits are necessary to ensure State Medicaid payment systems promote economy and efficiency. We are allowing a higher upper limit for payment to non-State public hospitals to recognize the higher costs of inpatient and outpatient services in public hospitals. In addition, to ensure continued beneficiary access to care and the ability of States to adjust to the changes in the upper payment limits, the final rule includes a transition period for States with approved rate enhancement State plan amendments.

Morphology and sedimentology of glacigenic submarine fans on the west Greenland continental margin

NASA Astrophysics Data System (ADS)

O'Cofaigh, Colm; Hogan, Kelly A.; Dowdeswell, Julian A.; Jennings, Anne E.; Noormets, Riko; Evans, Jeffrey

2014-05-01

Along the West Greenland continental margin adjoining Baffin Bay, bathymetric data show a series of large submarine fans located at the mouths of cross-shelf troughs. Two of these fans, the Uummannaq Fan and the Disko Fan are trough-mouth fans built largely of debris delivered from ice sheet outlets of the Greenland Ice Sheet during past glacial maxima. On the Uummannaq Fan glacigenic debris flow deposits occur on the upper slope and extend to at least 1800 m water depth in front of the trough-mouth. The debris flow deposits are related to the remobilisation of subglacial debris that was delivered onto the upper slope at times when an ice stream was positioned at the shelf edge. In contrast, sedimentary facies from the northern sector of the fan are characterised by hemipelagic and ice-rafted sediments and turbidites; glacigenic debris flows are notably absent in cores from this region. Further south along the Greenland continental margin the surface of the Disko Fan is prominently channelised and associated sediments are acoustically stratified. Although glacigenic debris flow deposits do occur on the upper Disko Fan, sediments recovered in cores from elsewhere on the fan record the influence of turbidity current and meltwater sedimentation. The channelised form of the Disko fan contrasts markedly with that of the Uummannaq Fan and, more widely, with trough mouth fans from the Polar North Atlantic. Collectively these data highlight the variability of glacimarine depositional processes operating on trough-mouth fans on high-latitude continental slopes and show that glacigenic debris flows are but one of a number of mechanisms by which such large glacially-influenced depocentres form.

Identification of third-order (approx. 10{sup 6} yrs) and fourth-order (approx. 10{sup 5}/10{sup 4} yrs) stratigraphic cycles in the South Addition, West Cameron Lease Area, Louisiana offshore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowrie, A.; Meeks, P.; Hoffman, K.

In the highly explored South Addition of the West Cameron Lease Area, Louisiana offshore, interpretation of a six-mile ({approx}10 km) seismic section across a single intraslope basin yielded 20 sediment packages. Several interpretive tools were necessary. Seismic stratigraphy indicated that the shallower zone was an outer shelf marked by 8 major sea level oscillations. In the portion between 1 and 3 seconds, seismic stratigraphy and paleontology led to the interpretation of depositional environments such as upper slope, and paleobathymetrically deeper intervals with descent through the section. The intraslope basin, while small, may be viewed as a micro-continental margin. Each seamore » level oscillation cycle apparently made a distinct progradational unit, decipherable in the seismic data. Fourth order cycles have been provisionally interpreted, throughout most of the entire 3.7 second section. Such precision is possible only in explored basins with excellent seismic data. The sequence thickness showed a seven-fold variability, from 0.08 to 0.58 seconds. The shallower section, deposited along an outer shelf, has an average individual sequence thickness of 0.13 seconds. Individual seismic sequences in the deeper section, interpreted to have been deposited on an upper slope, have average thicknesses of 0.25 seconds. The thinner sequences of the shallower section are compatible with the notion that the outer shelf was a bypass zone during a glacial epoch. The thicker sequences of the deeper section are the result of deposition onto an aggrading upper slope within an intraslope basin during a highstand.« less

Fronts and intrusions in the upper Deep Polar Water of the Eurasian and Makarov basins

NASA Astrophysics Data System (ADS)

Kuzmina, Natalia; Rudels, Bert; Zhurbas, Natalia; Lyzhkov, Dmitry

2013-04-01

CTD data obtained in the Arctic Basin are analyzed to describe structural features of intrusive layers and fronts encountered in the upper Deep Polar Water. This work is an extension of Arctic intrusions studies by Rudels et al. (1999) and Kuzmina et al. (2011). Numerous examples of fronts and intrusions observed in a deep layer (depth range of 600-1300 m) in the Eurasian and Makarov basins where salinity is increasing, and temperature is decreasing with depth (stable-stable thermohaline stratification), are described. The data are used to estimate hydrological parameters capable of determining different types of fronts and characterizing intrusive layers depending on the front structure. Coherence of intrusive layers is shown to get broken with the change of front structure. An evidence is found that enhanced turbulent mixing above local bottom elevations can prevent from intrusive layering. A linear stability model description of the observed intrusions is developed based on the Merryfield's (2000) assumption that interleaving is caused by differential mixing. Theoretical analysis is focused on prediction of the slopes of unstable modes at baroclinic and thermohaline fronts. Apparent vertical diffusivity due to turbulent mixing at baroclinic and thermohaline fronts is estimated on the basis of comparison of observed intrusion slopes with modeled slopes of the most unstable modes. Apparent lateral diffusivity is estimated too, based on Joyce (1980) approach. These estimates show that intrusive instability of fronts caused by differential mixing can result in sizable values of apparent lateral heat diffusivity in the deep Arctic layer that are quite comparable with those of the upper and intermediate Arctic layers (Walsh, Carmack, 2003; Kuzmina et al., 2011).

Relationship Between Topography and the Eastern Equatorial Hydrogen Signal on Mars

NASA Astrophysics Data System (ADS)

Clevy, J. R.; Elphic, R. C.; Feldman, W. C.; Kattenhorn, S. A.

2005-12-01

Epithermal neutron flux data received from the Neutron Spectrometer, part of the Gamma Ray Spectrometer suite on board NASA's Mars Odyssey, indicates elevated equatorial hydrogen deposits partially encircle the Schiaparelli Basin. Deconvolution of the hydrogen signal statistically increased the resolution over the spectrometer's original 600 km footprint. The resulting map of hydrogen concentrations was further refined by ignoring all data <8.9% Water Equivalent Hydrogen (WEH). In so doing, this study provides the most detailed map to date of the hydrogen concentration maxima in this region and serves as a guide for future exploration. Projecting the Eastern Equatorial Hydrogen map onto the digital elevation model for the Schiaparelli Basin reveals several areas of interest. For simplification, these areas are identified by clock position relative to Schiaparelli. At the twelve o'clock position, a maximum exceeding 10% WEH occupies the upper, northern slope of a saddle between Henry Crater and unnamed craters west of Henry. Viking images of the nameless craters demonstrate wind streaks from the north veer to the southwest here, following topography. Surface drainage channels are apparent on the slope below the local WEH maximum. The 2:30 maximum lies over Tuscaloosa Crater and Verde Vallis. This >10% WEH maximum has the greatest aerial extent, roughly 200 km in diameter. At 5 o'clock, the fringing range adjacent to Brazos Valles lies within the surficially dark region called Sinus Sabaeus. It should be noted that projection of the albedo map over the terrain reveals dark grains concentrating in low areas, presumably having moved short distances by wind and gravity. The absence or presence of these grains does not seem to affect the measured WEH concentration as the signal's local maximum, about 10.2%, crosses areas of high and low albedo without an increase or decrease in signal strength. At 6 o'clock, two 10.4% WEH maxima line the north-facing slope of another mountain range. Both maxima are elongated, east to west. The maximum at the top of the peak overlaps the cirque-like bowl of an unnamed, degraded crater. Below the collapsed north wall of this crater sits another maximum, 100 km long by 50 km wide. The eastern end of this lower maximum contains a crater with a 6 km wide, 40 km long drainage channel leading out of the crater and down the slope toward Schiaparelli. The final WEH maximum, at 6:30, is 150 km wide by 180 km long and is centered over Evros Vallis. The maximum extends beyond Sabaeus into Noachis Terra without visibly increasing or decreasing at the albedo boundary. From this study it is clear that albedo features do not control the hydrogen signal. WEH concentrations were found both within and outside Sabaeus. It is also apparent that drainage channels are present near each maximum. This proximity may implicate areas of high WEH as the source of channel-carving fluids. Finally, WEH is not tied to a specific stratigraphic layer. The locations of the maxima can be grouped into north-facing slopes, both peaks and saddles, and broad plains containing well-developed drainage systems flowing away from the WEH maxima. The former could indicate up-slope orographic deposition of hydrogen in the form of water ice as air masses rise and cool, preferentially coating north-facing slopes. High signals in low plains may be related to subsequent drainage when temperatures were warm enough to permit flow without immediate sublimation.

DETAIL VIEW OF WINCHING ENGINE LOCATED AT THE UPPER TRAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF WINCHING ENGINE LOCATED AT THE UPPER TRAM TERMINAL, LOOKING NORTHEAST. THE CABLE FROM THIS ENGINE LEADS DOWN INTO THE DEEP RAVINE IN FRONT OF THE UPPER TRAM TERMINAL. IT WAS PROBABLY USED TO DRAG MATERIALS UP TOWARD THE TERMINAL WHEN THE TERMINAL WAS BEING CONSTRUCTED, OR IN TIMES OF TRAMWAY BREAKDOWN. THE DRIVE ENGINE IS IN THE BACKGROUND. TWO LONG OPERATING LEVERS FOR THE ENGINE ARE IN THE CENTER FOREGROUND. AN EXTRA SPOOL OF CABLE IS ON THE GROUND TO THE RIGHT OF THE ENGINE. A WATER PIPELINE STRETCHES ACROSS THE SLOPE IN THE BACKGROUND, CARRYING WATER TO THE UPPER MINES. SEE CA-291-37 FOR IDENTICAL B&W NEGATIVE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL VIEW OF WINCHING ENGINE LOCATED AT THE UPPER TRAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF WINCHING ENGINE LOCATED AT THE UPPER TRAM TERMINAL LOOKING NORTHEAST. THE CABLE FROM THIS ENGINE LEADS DOWN INTO THE DEEP RAVINE IN FRONT OF THE UPPER TRAM TERMINAL. IT WAS PROBABLY USED TO DRAG MATERIALS UP TOWARD THE TERMINAL WHEN THE TERMINAL WAS BEING CONSTRUCTED, OR IN TIMES OF TRAMWAY BREAK DOWN. THE DRIVE ENGINE IS IN THE BACKGROUND. TWO LONG OPERATING LEVERS FOR THE ENGINE ARE IN THE CENTER FOREGROUND. AN EXTRA SPOOL OF CABLE IS ON THE GROUND TO THE RIGHT OF THE ENGINE. A WATER PIPELINE STRETCHES ACROSS THE SLOPE IN THE BACKGROUND, CARRYING WATER TO THE UPPER MINES. SEE CA-291-52 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Influence of submarine morphology on bottom water flow across the western Ross Sea continental margin

USGS Publications Warehouse

Davey, F.J.; Jacobs, S.S.

2007-01-01

Multibeam sonar bathymetry documents a lack of significant channels crossing outer continental shelf and slope of the western Ross Sea. This indicates that movement of bottom water across the shelf break into the deep ocean in this area is mainly by laminar or sheet flow. Subtle, ~20 m deep and up to 1000 m wide channels extend down the continental slope, into tributary drainage patterns on the upper rise, and then major erosional submarine canyons. These down-slope channels may have been formed by episodic pulses of rapid down slope water flow, some recorded on bottom current meters, or by sub-ice melt water erosion from an icesheet grounded at the margin. Narrow, mostly linear furrows on the continental shelf thought to be caused by iceberg scouring are randomly oriented, have widths generally less than 400 m and depths less than 30m, and extend to water depths in excess of 600 m.

Large and giant hydrocarbon accumulations in the transitional continent-ocean zone

NASA Astrophysics Data System (ADS)

Khain, V. E.; Polyakova, I. D.

2008-05-01

The petroleum resource potential is considered for the Atlantic, West Pacific, and East Pacific types of deepwater continental margins. The most considerable energy resources are concentrated at the Atlantic-type passive margins in the zone transitional to the ocean. The less studied continental slope of backarc seas of the generally active margins of the West Pacific type is currently not so rich in discoveries as the Atlantic-type margin, but is not devoid of certain expectations. In some of their parameters, the margins bounded by continental slopes may be regarded as analogs of classical passive margins. At the margins of the East Pacific type, the petroleum potential is solely confined to transform segments. In the shelf-continental-slope basins of the rift and pull-apart nature, petroleum fields occur largely in the upper fan complex, and to a lesser extent in the lower graben (rift) complex. In light of world experience, the shelf-continental-slope basins of the Arctic and Pacific margins of Russia are evaluated as highly promising.

Stability of sulfur slopes on Io

NASA Technical Reports Server (NTRS)

Clow, G. D.; Carr, M. H.

1980-01-01

The mechanical properties of elemental sulfur are such that the upper crust of Io cannot be primarily sulfur. For heat flows in the range 100-1000 ergs/sq cm sec sulfur becomes ductile within several hundred meters of the surface and would prevent the formation of calderas with depths greater than this. However, the one caldera for which precise depth data are available is 2 km deep, and this value may be typical. A study of the mechanical equilibrium of simple slopes shows that the depth to the zone of rapid ductile flow strongly controls the maximum heights for sulfur slopes. Sulfur scarps with heights greater than 1 km will fail for all heat flows greater than 180 ergs/sq cm sec and slope angles greater than 22.5 deg. The observed relief on Io is inconsistent with that anticipated for a predominantly sulfur crust. However, a silicate crust with several percent sulfur included satisfies both the mechanical constraints and the observed presence of sulfur on Io.

Reconstruction of the energy and depth of maximum of cosmic-ray air showers from LOPES radio measurements

NASA Astrophysics Data System (ADS)

Apel, W. D.; Arteaga-Velazquez, J. C.; Bähren, L.; Bekk, K.; Bertaina, M.; Biermann, P. L.; Blümer, J.; Bozdog, H.; Brancus, I. M.; Cantoni, E.; Chiavassa, A.; Daumiller, K.; de Souza, V.; di Pierro, F.; Doll, P.; Engel, R.; Falcke, H.; Fuchs, B.; Fuhrmann, D.; Gemmeke, H.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Horneffer, A.; Huber, D.; Huege, T.; Isar, P. G.; Kampert, K.-H.; Kang, D.; Krömer, O.; Kuijpers, J.; Link, K.; Łuczak, P.; Ludwig, M.; Mathes, H. J.; Melissas, M.; Morello, C.; Oehlschläger, J.; Palmieri, N.; Pierog, T.; Rautenberg, J.; Rebel, H.; Roth, M.; Rühle, C.; Saftoiu, A.; Schieler, H.; Schmidt, A.; Schröder, F. G.; Sima, O.; Toma, G.; Trinchero, G. C.; Weindl, A.; Wochele, J.; Zabierowski, J.; Zensus, J. A.; Lopes Collaboration

2014-09-01

LOPES is a digital radio interferometer located at Karlsruhe Institute of Technology (KIT), Germany, that measures radio emission from extensive air showers at MHz frequencies in coincidence with KASCADE-Grande. In this article, we explore a method (slope method) that leverages the slope of the measured radio lateral distribution to reconstruct crucial attributes of primary cosmic rays. First, we present an investigation of the method on the basis of pure simulations. Second, we directly apply the slope method to LOPES measurements. Applying the slope method to simulations, we obtain uncertainties on the reconstruction of energy and depth of shower maximum (Xmax) of 13% and 50 g /cm2, respectively. Applying it to LOPES measurements, we are able to reconstruct energy and Xmax of individual events with upper limits on the precision of 20%-25% for the primary energy and 95 g /cm2 for Xmax, despite strong human-made noise at the LOPES site.

Pulling up the runaway: the effect of new evidence on euthanasia's slippery slope.

PubMed

Ryan, C J

1998-10-01

The slippery slope argument has been the mainstay of many of those opposed to the legalisation of physician-assisted suicide and euthanasia. In this paper I re-examine the slippery slope in the light of two recent studies that examined the prevalence of medical decisions concerning the end of life in the Netherlands and in Australia. I argue that these two studies have robbed the slippery slope of the source of its power--its intuitive obviousness. Finally I propose that, contrary to the warnings of the slippery slope, the available evidence suggests that the legalisation of physician-assisted suicide might actually decrease the prevalence of non-voluntary and involuntary euthanasia.

Pulling up the runaway: the effect of new evidence on euthanasia's slippery slope.

PubMed Central

Ryan, C J

1998-01-01

The slippery slope argument has been the mainstay of many of those opposed to the legalisation of physician-assisted suicide and euthanasia. In this paper I re-examine the slippery slope in the light of two recent studies that examined the prevalence of medical decisions concerning the end of life in the Netherlands and in Australia. I argue that these two studies have robbed the slippery slope of the source of its power--its intuitive obviousness. Finally I propose that, contrary to the warnings of the slippery slope, the available evidence suggests that the legalisation of physician-assisted suicide might actually decrease the prevalence of non-voluntary and involuntary euthanasia. PMID:9800591

Results of Laboratory Tests on Surficial Sediments from the Upper Continental Slope Northern Gulf of Mexico

USGS Publications Warehouse

Booth, James S.

1979-01-01

The purpose of this report is to present the results of geo­technical, textural, and chemical tests performed on samples from the upper Continental Slope, northern Gulf of Mexico.The samples were collected by a piston corer up to 12 m (40 ft.} in length with a head weight of 908 kg (one ton}. The inside diameter of the C. A. B. liner was 89 mm (3.5 inches}. Upon retrieval, the cores were cut in 1.5 m sections, examined for evidence of disturbance, then, if in acceptable condition, were sealed and placed in their in situ vertical position in a refrigerated van. Once ashore, the sections were opened, sealed with wax, recapped and stored as before.The cores were split lengthwise for analysis. One half of the core was X-rayed and the radiograph was carefully examined as a further check for disturbance. This half was then archived. The other half of the core was used for the laboratory work.

Geometries for roughness shapes in laminar flow

NASA Technical Reports Server (NTRS)

Holmes, Bruce J. (Inventor); Martin, Glenn L. (Inventor); Domack, Christopher S. (Inventor); Obara, Clifford J. (Inventor); Hassan, Ahmed A. (Inventor)

1986-01-01

A passive interface mechanism between upper and lower skin structures, and a leading edge structure of a laminar flow airfoil is described. The interface mechanism takes many shapes. All are designed to be different than the sharp orthogonal arrangement prevalent in the prior art. The shapes of the interface structures are generally of two types: steps away from the centerline of the airfoil with a sloping surface directed toward the trailing edge and, the other design has a gap before the sloping surface. By properly shaping the step, the critical step height is increased by more than 50% over the orthogonal edged step.

Cold-seep carbonates of the middle and lower continental slope, northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Roberts, Harry H.; Feng, Dong; Joye, Samantha B.

2010-11-01

Authigenic carbonates from cold seeps on the middle and lower continental slope of the northern Gulf of Mexico (GOM) exhibit a wide range of mineralogical and stable isotopic compositions. These carbonates consist of concretions and nodules in surface sediments, hardgrounds of crusts and isolated slabs, and mounded buildups of blocks and slabs of up to over 10 meters in relief above the surrounding seafloor. Mineralogically, the carbonates are dominated by high-Mg calcite (HMC) and aragonite. However, low levels (<5 wt%) of dolomite are present in most samples. Petrographically, Mg-calcite peloidal matrix and acicular to botryoidal aragonitic void-filling cements are the most frequent associations. The carbon isotopic compositions of the carbonates range from -60.8 to 14.0‰ PDB, indicating complex carbon sources that include 13C-depleted biogenic and thermogenic methane, biodegraded crude oil, seawater CO2, and 13C-enriched residual CO2 from methanogenesis. A similarly large variability in δ18O values (2.5 to 6.7‰ PDB) demonstrates the geochemical complexity of the slope, with some samples pointing toward an 18O-enriched oxygen source that is possibly related to advection of 18O-enriched formation water and/or to the decomposition of gas hydrate. A considerable range of mineralogical and isotopic variations in cold-seep carbonate composition was noted even within individual study sites. However, common trends occur across multiple geographic areas. This situation suggests that local controls on fluid and gas flux, types of seep hydrocarbons, the presence or absence of gas hydrate in the near-surface sediment, and chemosynthetic communities, as well as the temporal evolution of the local hydrocarbon reservoir, all may play a part in determining carbonate mineralogy and isotope geochemistry. The carbon isotope data clearly indicate that between-site variation is greater than within-site variation. Seep carbonates formed on the middle and lower continental slope of the GOM do not appear to be substantially different from those found on the upper slope (<1000-m water depth). The highly variable fluids and gases that leave their geochemical imprints on seep carbonate of the middle and lower continental slope are similar to their outer shelf and upper slope counterparts.

Louisiana continental slope: geologic and seismic stratigraphic framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ray, P.K.; Cooke, D.W.

1987-05-01

The continental slope of Louisiana from Green Canyon to Mississippi Canyon was studied by interpreting seismic CDP data and wells in the area. The slope is characterized by blocked canyon intraslope basins of various dimensions with maximum thickness of sediments in excess of 21,000 ft, rotational slump blocks and large-scale submarine slides. In the subsurface, the outer shelf and upper slope show contrasting character with that of the lower slope, especially below the Sigsbee Scarp. The seismic stratigraphic units established for the deep sea area can be recognized in their entirety up to a water depth of 6000 to 5500more » ft. In shallower water salt tectonics obliterates the sequence. Fragmental records of the sequence, especially the top of Challenger boundary, have been recognized in as shallow as 2000 to 3000 ft of water. The Tertiary units often downlap and onlap directly on the Challenger unit, indicating the progradational nature of the clastic slope. The Sigsbee unit has been traced through the entire slope area and can be divided into five subunits of unique acoustical characteristics. The slope constantly regrades in response to Neogene sea level fluctuations. Loading of the shelf by deltaic deposition contributes to salt sill formation and flowage of salt over deep-water sediments on the slope during high sea level. Regressive sea is represented by slope failure, formation of large-scale submarine slides, filling of blocked canyon intraslope basins which show similar seismic facies to that of Orca and Pigmy basins as reported from DSDP studies, and sporadic uplifting of salt diapirs and massifs and the formation of linear transverse salt ridges.« less

Dynamics of Soil Organic Carbon and Microbial Biomass Carbon in Relation to Water Erosion and Tillage Erosion

PubMed Central

Xiaojun, Nie; Jianhui, Zhang; Zhengan, Su

2013-01-01

Dynamics of soil organic carbon (SOC) are associated with soil erosion, yet there is a shortage of research concerning the relationship between soil erosion, SOC, and especially microbial biomass carbon (MBC). In this paper, we selected two typical slope landscapes including gentle and steep slopes from the Sichuan Basin, China, and used the 137Cs technique to determine the effects of water erosion and tillage erosion on the dynamics of SOC and MBC. Soil samples for the determination of 137Cs, SOC, MBC and soil particle-size fractions were collected on two types of contrasting hillslopes. 137Cs data revealed that soil loss occurred at upper slope positions of the two landscapes and soil accumulation at the lower slope positions. Soil erosion rates as well as distribution patterns of the <0.002-mm clay shows that water erosion is the major process of soil redistribution in the gentle slope landscape, while tillage erosion acts as the dominant process of soil redistribution in the steep slope landscape. In gentle slope landscapes, both SOC and MBC contents increased downslope and these distribution patterns were closely linked to soil redistribution rates. In steep slope landscapes, only SOC contents increased downslope, dependent on soil redistribution. It is noticeable that MBC/SOC ratios were significantly lower in gentle slope landscapes than in steep slope landscapes, implying that water erosion has a negative effect on the microbial biomass compared with tillage erosion. It is suggested that MBC dynamics are closely associated with soil redistribution by water erosion but independent of that by tillage erosion, while SOC dynamics are influenced by soil redistribution by both water erosion and tillage erosion. PMID:23717530

Modern configuration of the southwest Florida carbonate slope: Development by shelf margin progradation

USGS Publications Warehouse

Brooks, G.R.; Holmes, C.W.

1990-01-01

Depositional patterns and sedimentary processes influencing modern southwest Florida carbonate slope development have been identified based upon slope morphology, seismic facies and surface sediment characteristics. Three slope-parallel zones have been identified: (1) an upper slope progradational zone (100-500 m) characterized by seaward-trending progradational clinoforms and sediments rich in shelf-derived carbonate material, (2) a lower gullied slope zone (500-800 m) characterized by numerous gullies formed by the downslope transport of gravity flows, and (3) a base-of-slope zone (> 800 m) characterized by thin, lens-shaped gravity flow deposits and irregular topography interpreted to be the result of bottom currents and slope failure along the basal extensions of gullies. Modern slope development is interpreted to have been controlled by the offshelf transport of shallow-water material from the adjacent west Florida shelf, deposition of this material along a seaward advancing sediment front, and intermittent bypassing of the lower slope by sediments transported in the form of gravity flows via gullies. Sediments are transported offshelf by a combination of tides and the Loop Current, augmented by the passage of storm frontal systems. Winter storm fronts produce cold, dense, sediment-laden water that cascades offshelf beneath the strong, eastward flowing Florida Current. Sediments are eventually deposited in a relatively low energy transition zone between the Florida Current on the surface and a deep westward flowing counter current. The influence of the Florida Current is evident in the easternmost part of the study area as eastward prograding sediments form a sediment drift that is progressively burying the Pourtales Terrace. The modern southwest Florida slope has seismic reflection and sedimentological characteristics in common with slopes bordering both the non-rimmed west Florida margin and the rimmed platform of the northern Bahamas, and shows many similarities to the progradational Miocene section along the west Florida slope. As with rimmed platform slopes, development of non-rimmed platform slopes can be complex and controlled by a combination of processes that result in a variety of configurations. Consequently, the distinction between the two slope types based solely upon seismic and sedimentological characteristics may not be readily discernible. ?? 1990.

Geotechnical Characteristics and Stability Analysis of Rock-Soil Aggregate Slope at the Gushui Hydropower Station, Southwest China

PubMed Central

Shi, Chong; Xu, Fu-gang

2013-01-01

Two important features of the high slopes at Gushui Hydropower Station are layered accumulations (rock-soil aggregate) and multilevel toppling failures of plate rock masses; the Gendakan slope is selected for case study in this paper. Geological processes of the layered accumulation of rock and soil particles are carried out by the movement of water flow; the main reasons for the toppling failure of plate rock masses are the increasing weight of the upper rock-soil aggregate and mountain erosion by river water. Indoor triaxial compression test results show that, the cohesion and friction angle of the rock-soil aggregate decreased with the increasing water content; the cohesion and the friction angle for natural rock-soil aggregate are 57.7 kPa and 31.3° and 26.1 kPa and 29.1° for saturated rock-soil aggregate, respectively. The deformation and failure mechanism of the rock-soil aggregate slope is a progressive process, and local landslides will occur step by step. Three-dimensional limit equilibrium analysis results show that the minimum safety factor of Gendakan slope is 0.953 when the rock-soil aggregate is saturated, and small scale of landslide will happen at the lower slope. PMID:24082854

Geotechnical characteristics and stability analysis of rock-soil aggregate slope at the Gushui Hydropower Station, southwest China.

PubMed

Zhou, Jia-wen; Shi, Chong; Xu, Fu-gang

2013-01-01

Two important features of the high slopes at Gushui Hydropower Station are layered accumulations (rock-soil aggregate) and multilevel toppling failures of plate rock masses; the Gendakan slope is selected for case study in this paper. Geological processes of the layered accumulation of rock and soil particles are carried out by the movement of water flow; the main reasons for the toppling failure of plate rock masses are the increasing weight of the upper rock-soil aggregate and mountain erosion by river water. Indoor triaxial compression test results show that, the cohesion and friction angle of the rock-soil aggregate decreased with the increasing water content; the cohesion and the friction angle for natural rock-soil aggregate are 57.7 kPa and 31.3° and 26.1 kPa and 29.1° for saturated rock-soil aggregate, respectively. The deformation and failure mechanism of the rock-soil aggregate slope is a progressive process, and local landslides will occur step by step. Three-dimensional limit equilibrium analysis results show that the minimum safety factor of Gendakan slope is 0.953 when the rock-soil aggregate is saturated, and small scale of landslide will happen at the lower slope.

Vascular plant species richness along environmental gradients in a cool temperate to sub-alpine mountainous zone in central Japan.

PubMed

Tsujino, Riyou; Yumoto, Takakazu

2013-03-01

In order to clarify how vegetation types change along the environmental gradients in a cool temperate to sub-alpine mountainous zone and the determinant factors that define plant species richness, we established 360 plots (each 4 × 10 m) within which the vegetation type, species richness, elevation, topographic position index (TPI), slope inclination, and ground light index (GLI) of the natural vegetation were surveyed. Mean elevation, TPI, slope inclination, and GLI differed across vegetation types. Tree species richness was negatively correlated with elevation, whereas fern and herb species richness were positively correlated. Tree species richness was greater in the upper slope area than the lower slope area, whereas fern and herb species richness were greater in the lower slope area. Ferns and trees species richness were smaller in the open canopy, whereas herb species richness was greater in the open canopy. Vegetation types were determined firstly by elevation and secondary by topographic configurations, such as topographic position, and slope inclination. Elevation and topography were the most important factors affecting plant richness, but the most influential variables differed among plant life-form groups. Moreover, the species richness responses to these environmental gradients greatly differed among ferns, herbs, and trees.

Topographic position, but not slope aspect, drives the dominance of functional strategies of tropical dry forest trees

NASA Astrophysics Data System (ADS)

Méndez-Toribio, M.; Ibarra-Manríquez, G.; Navarrete-Segueda, A.; Paz, H.

2017-08-01

In seasonal plant communities, it is recognized that topography-related variation in water availability and solar radiation determine vegetation structure and community composition; however, the effects on functional structure, particularly through changes in resource use strategies of plants are still poorly understood. This study examines the effects of slope aspect and topographic position on functional trait dominance in a tropical dry forest landscape and explores whether strategies for coping with drought (avoidance vs. tolerance) segregate spatially along the water stress gradient created by the interaction of these two topographic factors. The study was conducted in the Balsas river basin in south-central Mexico. Functional traits were evaluated in 63 species of trees (≥ 2.5 cm diameter at breast height) dominant in plots located at three topographic positions (low, medium and high) and on two slope aspects (north and south). Eight leaf and four stem functional traits, relating to the plants’ ability to avoid or tolerate water and temperature stress, were measured. Community-level functional traits were strongly affected by topographic position while only a weak signal was detected by the slope aspect. Contrary to our expectations, attributes associated with drought tolerance predominated on the lower topographic positions of the slopes, (moister and warmer sites), while on the upper parts with drier soil, but cooler air, attributes associated with water stress avoidance dominated. In addition, variation in the dominance of leaf pulvini and trichomes along the topographic gradient suggests environmental filtering by elevated air temperatures and water stress, respectively. Overall, our results suggest that the upper topographic positions that generate a shorter and more fluctuating water-availability window, favor readily-deciduous plants with high levels of water storage in their tissues, traits allowing for a rapid avoid of water stress, whereas on the lower topographic positions, where the soil remains moist for longer periods of time, tardily-deciduous species thrive with dense, low-water content tissues, attributes that are associated with physiological tolerance to drought.

Evidence of slope failure in the Sines Contourite Drift area (SW Portuguese Continental Margin) - preliminary results

NASA Astrophysics Data System (ADS)

Teixeira, Manuel; Roque, Cristina; Terrinha, Pedro; Rodrigues, Sara; Ercilla, Gemma; Casas, David

2017-04-01

Slope instability, expressed by landslide activity, is an important natural hazard both onshore as well as offshore. Offshore processes create great concern on coastal areas constituting one of the major and most prominent hazards, directly by the damages they generate and indirectly by the possibility of generating tsunamis, which may affect the coast line. The Southwest Portuguese Continental Margin has been identified as an area where several mass movements occurred from Late Pleistocene to Present. Recently, an area of 52 km long by 34 km wide, affected by slope failure has been recognized in the Sines contourite drift located off the Alentejo. SWIM and CONDRIBER multibeam swath bathymetry has been used for the geomorphologic analysis and for recognition of mass movement scars on the seabed. Scars' areas and volumes were calculated by reconstructing paleo-bathymetry. The net gain and net loss were calculated using both paleo and present day bathymetry. Geomorphologically, the study area presents 4 morphologic domains with landslide scars: I) Shelf and upper slope display an irregular boundary with domain II with a sharp step ( 150m - 600m); II) Smooth area with gentle slope angles making the transition from smoother area to the continental slope (scarp), with large scars, suggesting slow rate and distributed mass wasting processes over this area ( 600 - 1200m); III) Scarp with high rates of retrograding instability, where faster processes are verified and a great number of gullies is feeding downslope area (1200m - 3200m); IV) Lebre Basin where mass movements deposits accumulate (> 3200m). A total of 51 landslide scars were identified with a total affected area of 137.67 km2, with 80.9 km2 being located in the continental slope with about 59% of the disrupted area, between 1200 and 3200m, and 41% (56.6 km2) lies in the continental shelf and upper slope, on a range of depths between 150 and 800m. The mean scar area is 2.7 km2 and the maximum area recorded on a scar is 7.63 km2, while the minimum is 0.14 km2. About 43% of the scars present areas below 2 km2 and 63% below 3 km2. Only 3.9% of the scars present areas higher than 7 km2. There is a total volume of displaced material of 4.46 km3 with a mean volume of 0.1 km3. The maximum volume recorded on a scar is 0.45 km3, while the minimum is 0.01 km3. The volume of material removed is quite variable, although the major part of the scars corresponds to a very small volume of removed material, with 69% of the scars presenting less than 0.1 km3. About 55% of the scars are located in slopes <=7° and 20% in slopes between 0 and 2°, while 24% of the scars belong to the class of slope gradient between 1.5 and 3°. We may conclude that there is, apparently, a reverse relationship between slope angle and scar area, meaning that slope is not the main condition for big landslide scars and that the areas with steep slopes, such as fault escarpments, favour continuous fast retrograde erosion. Publication supported by FCT- project UID/GEO/50019/2013 - Instituto Dom Luiz

Ganges Chasma Landslide

NASA Technical Reports Server (NTRS)

2002-01-01

(Released 01 April 2002) This image shows a spectacular landslide along a portion of the southern wall of Ganges Chasma within Valles Marineris. Landslides have very characteristic morphologies on Earth, which they also display on Mars. These morphologies include a distinctive escarpment at the uppermost part of the landslide--called a head scarp (seen at the bottom of this image), a down-dropped block of material below that escarpment that dropped almost vertically, and a deposit of debris that moved away from the escarpment at high speed. In this example, the wall rock displayed in the upper part of the cliff is layered, with spurs and chutes created by differing amounts of erosion. Below the steep scarp is a smoother, steep slope of material with small, narrow tongues of debris that have eroded off of the escarpment since the landslide occurred (a talus slope). The actual landslide deposit, visible in the upper half of this image, shows striations that form by differences in the side-by-side motion during high velocity emplacement. This immense landslide traveled some 70 km at speeds that probably exceeded 100 kilometers per hour (60 miles per hour) before coming to rest, forming abrupt, terminal fronts (upper right corner of image). Even at these high speeds, this massive landslide was moving for nearly an hour before it came to rest.

Dome of magnetic order inside the nematic phase of sulfur-substituted FeSe under pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiang, Li; Kaluarachchi, Udhara; Bohmer, Anna

2017-07-18

The pressure dependence of the structural, magnetic, and superconducting transitions and of the superconducting upper critical field were studied in sulfur-substituted Fe ( Se 1 - x S x ) . We performed resistance measurements on single crystals with three substitution levels ( x = 0.043 , 0.096, 0.12) under hydrostatic pressures up to 1.8 GPa and in magnetic fields up to 9 T and were compared to data on pure FeSe. Our results illustrate the effects of chemical and physical pressure on Fe ( Se 1 - x S x ). Furthermore, on increasing sulfur content, magnetic order inmore » the low-pressure range is strongly suppressed to a small domelike region in the phase diagrams. But, T s is much less suppressed by sulfur substitution, and T c of Fe ( Se 1 - x S x ) exhibits similar nonmonotonic pressure dependence with a local maximum and a local minimum present in the low-pressure range for all x . The local maximum in T c coincides with the emergence of the magnetic order above T c . At this pressure the slope of the upper critical field decreases abruptly, which may indicate a Fermi-surface reconstruction. The minimum of T c correlates with a broad maximum of the upper critical field slope normalized by T c .« less

Upper triassic continental margin strata of the central alaska range: Implications for paleogeographic reconstruction

USGS Publications Warehouse

Till, A.B.; Harris, A.G.; Wardlaw, B.R.; Mullen, M.

2007-01-01

Reexamination of existing conodont collections from the central Alaska Range indicates that Upper Triassic marine slope and basin rocks range in age from at least as old as the late Carnian to the early middle Norian. The conodont assemblages typical of these rocks are generally cosmopolitan and do not define a distinct paleogeographic faunal realm. One collection, however, containsEpigondolella multidentata sensu Orchard 1991c, which appears to be restricted to western North American autochthonous rocks. Although paleogeographic relations cannot be determined with specificity, the present distribution of biofaces within the Upper Triassic sequence could not have been the result of simple accordion-style collapse of the Late Triassic margin.

The Hirnantian δ13C Positive Excursion in the Nabiullino Section (South Urals)

NASA Astrophysics Data System (ADS)

Yakupov, R. R.; Mavrinskaya, T. M.; Smoleva, I. V.

2018-02-01

The upper Sandbian, Katian, and Hirnantian complexes of conodonts in the upper Ordovician section of the western slope of the Southern Urals near the village of Nabiullino were studied. The δ13C positive excursion with a maximum of 3.3‰ associated with the global Hirnantian isotopic event, HICE, was fixed for the first time. This excursion shows the beginning of the Hirnantian stage in the terrigenous-carbonate section of the upper Ordovician in the Southern Urals. It coincides with the first occurrence of the Hirnantian conodont species of Gamachignathus ensifer and the conodonts of shallow-water biophacies, Aphelognathus-Ozarkodina, reflecting the global glacio-eustatic event.

Limitation of the Predominant-Period Estimator for Earthquake Early Warning and the Initial Rupture of Earthquakes

NASA Astrophysics Data System (ADS)

Yamada, T.; Ide, S.

2007-12-01

Earthquake early warning is an important and challenging issue for the reduction of the seismic damage, especially for the mitigation of human suffering. One of the most important problems in earthquake early warning systems is how immediately we can estimate the final size of an earthquake after we observe the ground motion. It is relevant to the problem whether the initial rupture of an earthquake has some information associated with its final size. Nakamura (1988) developed the Urgent Earthquake Detection and Alarm System (UrEDAS). It calculates the predominant period of the P wave (τp) and estimates the magnitude of an earthquake immediately after the P wave arrival from the value of τpmax, or the maximum value of τp. The similar approach has been adapted by other earthquake alarm systems (e.g., Allen and Kanamori (2003)). To investigate the characteristic of the parameter τp and the effect of the length of the time window (TW) in the τpmax calculation, we analyze the high-frequency recordings of earthquakes at very close distances in the Mponeng mine in South Africa. We find that values of τpmax have upper and lower limits. For larger earthquakes whose source durations are longer than TW, the values of τpmax have an upper limit which depends on TW. On the other hand, the values for smaller earthquakes have a lower limit which is proportional to the sampling interval. For intermediate earthquakes, the values of τpmax are close to their typical source durations. These two limits and the slope for intermediate earthquakes yield an artificial final size dependence of τpmax in a wide size range. The parameter τpmax is useful for detecting large earthquakes and broadcasting earthquake early warnings. However, its dependence on the final size of earthquakes does not suggest that the earthquake rupture is deterministic. This is because τpmax does not always have a direct relation to the physical quantities of an earthquake.

Distribution patterns of the mesozooplankton, principally siphonophores and medusae, in the vicinity of the Antarctic Slope Front (eastern Weddell Sea)

NASA Astrophysics Data System (ADS)

Pagès, Francesc; Schnack-Schiel, Sigrid B.

1996-12-01

The composition, abundance and vertical distribution of mesozooplankton, particularly siphonophores and medusae (27 species), collected along two transects in the eastern Weddell Sea have been analysed. Both transects were characterized by a steep thermocline that on approaching the coastline defined the Antarctic Slope Front. The front acted as a strong boundary in the shelf-slope and caused a pronounced cross frontal gradient in the populations of cnidarians. Few species and low abundances were found in the upper cold waters and most of the populations concentrated in and below the thermocline. The analysis of the gastrozooids of the physonect siphonophore Pyrostephos vanhoeffeni showed a wide variety of prey but the relatively high contribution of krill larvae reveals a substantial trophic impact when both organisms co-occur.

On the Antarctic Slope Front and Current crossing of the South Scotia Ridge

NASA Astrophysics Data System (ADS)

Orsi, A. H.; Palmer, M.; Gomis, D.; Flexas, M. M.; Kim, Y.-S.; Jordà, G.; Wiederwohl, C.; Álvarez, M.

2012-04-01

To unveil the contorted path followed by the Antarctic Slope Current connecting the Weddell and Scotia Seas, hydrographic stations with unprecedented spatial resolution were occupied on a series of sections across the slope and multiple channels in the double-pronged western portion of the South Scotia Ridge. Fieldwork consisted of two cruises from the ESASSI (January 2008) and ACROSS (February 2009) programs, the Spanish and USA/Argentina components of the International Polar Year core project SASSI (Synoptic Antarctic Shelf-Slope Interaction study). In this region the Antarctic Slope Current can be located by the pronounced in-shore deepening of isopycnals over the continental slope, rendering the strong subsurface temperature and salinity gradients characteristic of the Antarctic Slope Front. Before reaching the gaps in the southern Ridge near 51°W and 50°W, the ASC carries about 3 Sv of upper layer waters, but it splits into shallow and deep branches upon turning north through these two gaps. The shallower branch enters the Hesperides Trough at 51°W, then shows a tight cyclonic loop back to that longitude roughly following the slope's 700-m isobath, and turns again westward through a similar gap in the northern Ridge. In the Scotia Sea the westward-flowing Antarctic Slope Current is found as far west as the Elephant Island along slightly deeper levels of slope (1100 m) before it is blocked by the Antarctic Circumpolar Current south of the Shackleton Fracture Zone (56°W). The deeper branch of the ASC in the Powell Basin crosses the southern Ridge near 50°W and roughly follows the 1600-m isobath before entering the Scotia Sea through the Hesperides Gap farther to the east (49°W). Thereafter the deeper waters carried westward by this branch become undistinguishable from those circulating farther offshore. Repeat cross-slope sections at both southern and northern flanks of the South Scotia Ridge showed significant temporal variability in the characteristics of the Antarctic Slope Front/Current system.

A statistical overview of mass movement characteristics on the North American Atlantic outer continental margin

USGS Publications Warehouse

Booth, James S.; O'Leary, Dennis W.

1992-01-01

An analysis of 179 mass movements on the North American Atlantic continental slope and upper rise shows that slope failures have occurred throughout the geographic extent of the outer margin. Although the slope failures show no striking affinity for a particular depth as an origination level, there is a broad, primary mode centered at about 900 m. The resulting slides terminate at almost all depths and have a primary mode at 1100 m, but the slope/rise boundary (at 2200 m) also is an important mode. Slope failures have occurred at declivities ranging from 1° to 30° (typically, 4°); the resultant mass movement deposits vary in width from 0.2 to 50 km (typically, 1-2 km) and in length from 0.3 to 380 km (typically, 2–4 km), and they have been reported to be as thick as 650 m. On a numeric basis, mass movements are slightly more prevalent on open slopes than in other physiographic settings, and both translational and rotational failure surfaces are common. The typical mass movement is disintegrative in nature. Open slope slides tend to occur at lower slope angles and are larger than canyon slides. Further, large‐scale slides rather than small‐scale slides tend to originate on gentle slopes (≍ 3-4°). Rotational slope failures appear to have a slightly greater chance of occurring in canyons, but there is no analogous bias associated with translational failures. Similarly, disintegrative slides seem more likely to be associated with rotational slope failures than translational ones and are longer than their nondisintegrative counterparts. The occurrence of such a variety of mass movements at low declivities implies that a regional failure mechanism has prevailed. We suggest that earthquakes or, perhaps in some areas, gas hydrates are the most likely cause of the slope failures.

Quasi-horizontal circulation cells in 3D seawater intrusion

USGS Publications Warehouse

Abarca, E.; Carrera, J.; Sanchez-Vila, X.; Voss, C.I.

2007-01-01

The seawater intrusion process is characterized by the difference in freshwater and seawater density that causes freshwater to float on seawater. Many confined aquifers have a large horizontal extension with respect to thickness. In these cases, while buoyancy acts in the vertical direction, flow is confined between the upper and bottom boundaries and the effect of gravity is controlled by variations of aquifer elevation. Therefore, the effective gravity is controlled by the slope and the shape of the aquifer boundaries. Variability in the topography of the aquifer boundaries is one case where 3D analysis is necessary. In this work, density-dependent flow processes caused by 3D aquifer geometry are studied numerically and specifically, considering a lateral slope of the aquifer boundaries. Sub-horizontal circulation cells are formed in the saltwater entering the aquifer. The penetration of the saltwater can be quantified by a dimensionless buoyancy number that measures the lateral slope of the aquifer relative to freshwater flux. The penetration of the seawater intrusion wedge is controlled more by this slope than by the aquifer thickness and dispersivity. Thus, the slope must be taken into account in order to accurately evaluate seawater intrusion. ?? 2007 Elsevier B.V. All rights reserved.

Deep-sea diversity patterns are shaped by energy availability.

PubMed

Woolley, Skipton N C; Tittensor, Derek P; Dunstan, Piers K; Guillera-Arroita, Gurutzeta; Lahoz-Monfort, José J; Wintle, Brendan A; Worm, Boris; O'Hara, Timothy D

2016-05-19

The deep ocean is the largest and least-explored ecosystem on Earth, and a uniquely energy-poor environment. The distribution, drivers and origins of deep-sea biodiversity remain unknown at global scales. Here we analyse a database of more than 165,000 distribution records of Ophiuroidea (brittle stars), a dominant component of sea-floor fauna, and find patterns of biodiversity unlike known terrestrial or coastal marine realms. Both patterns and environmental predictors of deep-sea (2,000-6,500 m) species richness fundamentally differ from those found in coastal (0-20 m), continental shelf (20-200 m), and upper-slope (200-2,000 m) waters. Continental shelf to upper-slope richness consistently peaks in tropical Indo-west Pacific and Caribbean (0-30°) latitudes, and is well explained by variations in water temperature. In contrast, deep-sea species show maximum richness at higher latitudes (30-50°), concentrated in areas of high carbon export flux and regions close to continental margins. We reconcile this structuring of oceanic biodiversity using a species-energy framework, with kinetic energy predicting shallow-water richness, while chemical energy (export productivity) and proximity to slope habitats drive deep-sea diversity. Our findings provide a global baseline for conservation efforts across the sea floor, and demonstrate that deep-sea ecosystems show a biodiversity pattern consistent with ecological theory, despite being different from other planetary-scale habitats.

Long-term responses of rainforest erosional systems at different spatial scales to selective logging and climatic change.

PubMed

Walsh, R P D; Bidin, K; Blake, W H; Chappell, N A; Clarke, M A; Douglas, I; Ghazali, R; Sayer, A M; Suhaimi, J; Tych, W; Annammala, K V

2011-11-27

Long-term (21-30 years) erosional responses of rainforest terrain in the Upper Segama catchment, Sabah, to selective logging are assessed at slope, small and large catchment scales. In the 0.44 km(2) Baru catchment, slope erosion measurements over 1990-2010 and sediment fingerprinting indicate that sediment sources 21 years after logging in 1989 are mainly road-linked, including fresh landslips and gullying of scars and toe deposits of 1994-1996 landslides. Analysis and modelling of 5-15 min stream-suspended sediment and discharge data demonstrate a reduction in storm-sediment response between 1996 and 2009, but not yet to pre-logging levels. An unmixing model using bed-sediment geochemical data indicates that 49 per cent of the 216 t km(-2) a(-1) 2009 sediment yield comes from 10 per cent of its area affected by road-linked landslides. Fallout (210)Pb and (137)Cs values from a lateral bench core indicate that sedimentation rates in the 721 km(2) Upper Segama catchment less than doubled with initially highly selective, low-slope logging in the 1980s, but rose 7-13 times when steep terrain was logged in 1992-1993 and 1999-2000. The need to keep steeplands under forest is emphasized if landsliding associated with current and predicted rises in extreme rainstorm magnitude-frequency is to be reduced in scale.

Development and sexual dimorphism of the sonic system in deep sea neobythitine fishes: The upper continental slope

NASA Astrophysics Data System (ADS)

Ali, Heba A.; Mok, Hin-Kiu; Fine, Michael L.

2016-09-01

The anatomy of sound production in continental-slope fishes has been ignored since the work of NB Marshall in the 1960s. Due to food scarcity at great depths, we hypothesize that sonic muscles will be reduced in deep-water neobythitine cusk-eels (family Ophidiidae). Here we describe and quantify dimensions of the swimbladder and sonic muscles of three species from the upper slope. They have four pairs of well-developed sonic muscles (two medial and two lateral) with origins on the skull and insertions on the medial swimbladder (medial pair) or on modified epineural ribs that attach to the lateral swimbladder (lateral pair). Despite minor differences, relatively similar swimbladder dimensions, muscle length and external morphology suggest a conservative body plan. However, there are major differences in sonic muscle mass: medial muscles are heavier in males and made of relatively small fibers (ca 10 μm in diameter). Lateral muscles are generally larger in females and consist of larger fibers, as in epaxial trunk muscle. Muscle weight varies between species, and we suggest males produce advertisement calls that vary in amplitude and duration in different species. Due to differences in fiber size, we hypothesize that lateral muscles with larger fibers remain contracted during sound production, and medial muscles with smaller fibers will oscillate to drive swimbladder sound production.

pCO2 Observations from a Vertical Profiler on the upper continental slope off Vancouver Island: Physical controls on biogeochemical processes.

NASA Astrophysics Data System (ADS)

Mihaly, S. F.

2016-02-01

We analyse two six month sets of data collected from a vertical profiler on Ocean Networks Canada's NEPTUNE observatory over the summer and early fall of 2012 and 2014. The profiler is in 400 m of water on the upper slope of the continental shelf. The site is away from direct influence of canyons, but is in a region of strong internal tide generation. Both seasonally varying semidiurnal internal tidal currents and diurnal shelf waves are observed. The near surface mean flow is weak and seasonally alternates between the California and Alaskan Currents. Mid-depth waters are influenced by the poleward flowing Californian undercurrent and the deep waters by seasonally varying wind-driven Ekman transport. The profiling package consists of a CTD, an oxygen optode, a pCO2 sensor, Chlorophyll fluorometer/turbidity, CDOM and is co-located with an upward-looking bottom-mounted 75kHz ADCP that measures currents to 30 m below sea surface. With these first deep-sea profiled time series measurements of pCO2, we endeavor to model how the local physical dynamics exert control over the variability of water properties over the slope and shelf and what the variability of the non-conservative tracers of pCO2 and O2 can tell us about the biogeochemistry of the region.

Investigation of feet functions of large ruminants with a decoupled model of equivalent mechanism

PubMed Central

Zhang, Qun; Ding, Xilun

2017-01-01

ABSTRACT Cloven hooves of ruminants adapt to diverse terrain, provide propulsive force and support the whole body during movement in natural environments. To reveal how the feet ensure terrain adaptability by choosing the proper configurations and terrain conditions, we model the feet of ruminants as an equivalent mechanism with flexion-extension and lateral movement decoupled. The upper part of the equivalent mechanism can flex and extend, while the lower part performs the lateral movement. Combination of the two parts can adapt to longitudinal slope (anterior-posterior) and transverse slope (medial-lateral), respectively. When one of two digits closes laterally, the workspace of the other decreases. The distal interdigital ligament between two digits limits their motion by elastic force and stores energy during movement. Differences in elastic energy variation of the ligament on different transverse slopes are characterized based on the configurations of two digits and the elastic energy between them. If the upper one of two symmetric digits is fixed, the foot landing on the grade surface (2°) shows greater capacity for absorbing energy; otherwise, level ground is the best choice for ruminants. As for the asymmetric digits, longer lateral digits enhance the optimal adaptive lateral angle. The asymmetry predisposes the feet to damage on the hard ground, which indicates soft ground is more suitable. PMID:28412713

Feeding of Greenland halibut (Reinhardtius hippoglossoides) in the Canadian Beaufort Sea

NASA Astrophysics Data System (ADS)

Giraldo, Carolina; Stasko, Ashley; Walkusz, Wojciech; Majewski, Andrew; Rosenberg, Bruno; Power, Michael; Swanson, Heidi; Reist, James D.

2018-07-01

Trophic patterns for Greenland Halibut are reported for the first time in the Canadian Beaufort Sea and Amundsen Gulf (n = 269). Samples were collected from 2012 to 2014 on the upper (300-500 m) and lower continental slope (750-1500 m) and were analyzed for stomach contents, stable isotopes ratios and fatty acids (FA). Stomach contents indicated that Arctic Cod, Boreogadus saida, was the main prey ingested on the upper slope (50-94% of total biomass) whereas Gelatinous Snailfish (Liparis fabricii) and Zoarcids (Lycodes spp.) dominated diets on the lower slope (17-62% of total biomass). Stable isotope mixing models and FA analyses also identified benthopelagic fishes (i.e., Liparis spp., B. saida) as key prey and highlighted large dietary overlap among years and between the two depth categories. Greenland Halibut were characterized by relatively wide δ13C and narrow δ15N ranges that suggested use of both pelagic and benthic energy sources and a piscivorous diet. Calanus-type markers such as 20:1n9 dominated the FA (>20% of total FA) andemphasized the importance of pelagic-derived material in the diet. The contribution of pelagic and benthic-derived matter in the diet suggests that Greenland Halibut play a major role in the benthic-pelagic coupling for deep water communities (up to 1500 m) in the Canadian Beaufort Sea.

Comparison of Surface Mountain Climate With Equivalent Free Air Parameters Extracted From NCEP/NCAR Reanalysis: Kilimanjaro, Tanzania.

NASA Astrophysics Data System (ADS)

Pepin, N. C.; Hardy, D.; Duane, W.; Losleben, M.

2007-12-01

It is difficult to predict future climate changes in areas of complex relief, since mountains generate their own climates distinct from the free atmosphere. Thus trends in climate at the mountain surface are different from those in the free air. We compare surface climate (temperature and vapour pressure) measured at seven elevations on the south-western slope of Kilimanjaro, the tallest free standing mountain in Africa, with equivalent observations in the free atmosphere from NCEP/NCAR reanalysis data for September 2004 to January 2006. Correlations between daily surface and free air temperature anomalies are greatest at low elevations below 2500 metres, meaning that synoptic (inter-diurnal) variability is the major control here. However, temperatures and moisture on the higher slopes above the treeline (3000 m) are decoupled from the free atmosphere, showing intense heating/cooling by day/night and import of moisture from lower elevations during the day. The lower forested slopes thus act as a moisture source, with large vapour pressure excesses reported in comparison with the free atmosphere (>5 hPa) which move upslope during daylight and subside downslope at night. Strong seasonal contrasts are shown in the vigour of the montane thermal circulation, but interactions with free air circulation (as represented by flow indices developed from reanalysis wind components) are complex. Upper air flow strength and direction (at 500 mb) have limited influence on surface heating and upslope moisture advection, which are dominated by the diurnal cycle rather than inter-diurnal synoptic controls. Thus local changes in surface characteristics (e.g. deforestation) could have a direct influence on the mountain climate of Kilimanjaro, making the upper slopes somewhat divorced from larger scale advective changes associated with global warming.

Subduction-Related Structure in the Mw 9.2, 1964 Megathrust Rupture Area Offshore Kodiak Island, Alaska

NASA Astrophysics Data System (ADS)

Krabbenhoeft, A.; von Huene, R.; Klaeschen, D.; Miller, J. J.

2016-12-01

Some of the largest earthquakes worldwide, including the 1964 9.2 Mw megathrust earthquake, occurred in Alaskan subduction zones. To better understand rupture processes and their mechanisms, we relate seafloor morphology from multibeam and regional bathymetric compilations with sub-seafloor images and seismic P-wave velocity structures. We re-processed legacy multichannel seismic (MCS) data including shot- and intra-shotgather interpolation, multiple removal and Kirchhoff depth migration. These images even reveal the shallow structure of the subducting oceanic crust. Traveltime tomography of a coincident vintage (1994) wide angle dataset reveals the P-wave velocity distribution as well as the deep structure of the subducting plate to the ocean crust Moho. The subducting oceanic crust morphology is rough and partly hidden by a thick sediment cover that reaches 3 km depth at the trench axis. Bathymetry shows two major contrasting upper plate morphologies: the shallow dipping lower slope consists of trench-parallel ridges that form the accreted prism whereas the steep rough middle and upper slopes are composed of competent older rock.Thrust faults are distributed across the entire slope, some of which connect with the subducted plate interface. A subtle change in seafloor gradient from the lower to the middle slope coincides with a thrust fault zone marking the boundary between the margin framework and the frontal prism. It corresponds to the most prominent lateral increase in seismic P-wave velocities, 25 km landward of the trench axis.Major thrusts in several MCS-lines are correlated with bathymetric data, showing their > 100 km lateral extent, which might also be tsunamigenic paths of earthquake rupture from the seismogenic zone to the seafloor.

Environmental drivers of spatial patterns of topsoil nitrogen and phosphorus under monsoon conditions in a complex terrain of South Korea

PubMed Central

Choi, Kwanghun; Spohn, Marie; Park, Soo Jin; Huwe, Bernd; Ließ, Mareike

2017-01-01

Nitrogen (N) and phosphorus (P) in topsoils are critical for plant nutrition. Relatively little is known about the spatial patterns of N and P in the organic layer of mountainous landscapes. Therefore, the spatial distributions of N and P in both the organic layer and the A horizon were analyzed using a light detection and ranging (LiDAR) digital elevation model and vegetation metrics. The objective of the study was to analyze the effect of vegetation and topography on the spatial patterns of N and P in a small watershed covered by forest in South Korea. Soil samples were collected using the conditioned latin hypercube method. LiDAR vegetation metrics, the normalized difference vegetation index (NDVI), and terrain parameters were derived as predictors. Spatial explicit predictions of N/P ratios were obtained using a random forest with uncertainty analysis. We tested different strategies of model validation (repeated 2-fold to 20-fold and leave-one-out cross validation). Repeated 10-fold cross validation was selected for model validation due to the comparatively high accuracy and low variance of prediction. Surface curvature was the best predictor of P contents in the organic layer and in the A horizon, while LiDAR vegetation metrics and NDVI were important predictors of N in the organic layer. N/P ratios increased with surface curvature and were higher on the convex upper slope than on the concave lower slope. This was due to P enrichment of the soil on the lower slope and a more even spatial distribution of N. Our digital soil maps showed that the topsoils on the upper slopes contained relatively little P. These findings are critical for understanding N and P dynamics in mountainous ecosystems. PMID:28837590

Numerical slope stability simulations of chasma walls in Valles Marineris/Mars using a distinct element method (dem).

NASA Astrophysics Data System (ADS)

Imre, B.

2003-04-01

NUMERICAL SLOPE STABILITY SIMULATIONS OF CHASMA WALLS IN VALLES MARINERIS/MARS USING A DISTINCT ELEMENT METHOD (DEM). B. Imre (1) (1) German Aerospace Center, Berlin Adlershof, bernd.imre@gmx.net The 8- to 10-km depths of Valles Marineris (VM) offer excellent views into the upper Martian crust. Layering, fracturing, lithology, stratigraphy and the content of volatiles have influenced the evolution of the Valles Marineris wallslopes. But these parameters also reflect the development of VM and its wall slopes. The scope of this work is to gain understanding in these parameters by back-simulating the development of wall slopes. For that purpose, the two dimensional Particle Flow Code PFC2D has been chosen (ITASCA, version 2.00-103). PFC2D is a distinct element code for numerical modelling of movements and interactions of assemblies of arbitrarily sized circular particles. Particles may be bonded together to represent a solid material. Movements of particles are unlimited. That is of importance because results of open systems with numerous unknown variables are non-unique and therefore highly path dependent. This DEM allows the simulation of whole development paths of VM walls what makes confirmation of the model more complete (e.g. Oreskes et al., Science 263, 1994). To reduce the number of unknown variables a proper (that means as simple as possible) field-site had to be selected. The northern wall of eastern Candor Chasma has been chosen. This wall is up to 8-km high and represents a significant outcrop of the upper Martian crust. It is quite uncomplex, well-aligned and of simple morphology. Currently the work on the model is at the stage of performing the parameter study. Results will be presented via poster by the EGS-Meeting.

Adaptive divergence in a scleractinian coral: physiological adaptation of Seriatopora hystrix to shallow and deep reef habitats

PubMed Central

2011-01-01

Background Divergent natural selection across environmental gradients has been acknowledged as a major driver of population and species divergence, however its role in the diversification of scleractinian corals remains poorly understood. Recently, it was demonstrated that the brooding coral Seriatopora hystrix and its algal endosymbionts (Symbiodinium) are genetically partitioned across reef environments (0-30 m) on the far northern Great Barrier Reef. Here, we explore the potential mechanisms underlying this differentiation and assess the stability of host-symbiont associations through a reciprocal transplantation experiment across habitats ('Back Reef', 'Upper Slope' and 'Deep Slope'), in combination with molecular (mtDNA and ITS2-DGGE) and photo-physiological analyses (respirometry and HPLC). Results The highest survival rates were observed for native transplants (measured 14 months after transplantation), indicating differential selective pressures between habitats. Host-symbiont assemblages remained stable during the experimental duration, demonstrating that the ability to "shuffle" or "switch" symbionts is restricted in S. hystrix. Photo-physiological differences were observed between transplants originating from the shallow and deep habitats, with indirect evidence of an increased heterotrophic capacity in native deep-water transplants (from the 'Deep Slope' habitat). Similar photo-acclimatisation potential was observed between transplants originating from the two shallow habitats ('Back Reef' and 'Upper Slope'), highlighting that their genetic segregation over depth may be due to other, non-photo-physiological traits under selection. Conclusions This study confirms that the observed habitat partitioning of S. hystrix (and associated Symbiodinium) is reflective of adaptive divergence along a depth gradient. Gene flow appears to be reduced due to divergent selection, highlighting the potential role of ecological mechanisms, in addition to physical dispersal barriers, in the diversification of scleractinian corals and their associated Symbiodinium. PMID:22004364

Slump dominated upper slope reservoir facies, Intra Qua Iboe (Pliocene), Edop Field, offshore Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shanmugam, G.; Hermance, W.E.; Olaifa, J.O.

An integration of sedimentologic and 3D seismic data provides a basis for unraveling complex depositional processes and sand distribution of the Intra Qua Iboe (IQI) reservoir (Pliocene), Edop Field, offshore Nigeria. Nearly 3,000 feet of conventional core was examined in interpreting slump/slide/debris flow, bottom current, turbidity current, pelagic/hemipelagic, wave and tide dominated facies. The IQI was deposited on an upper slope in close proximity to the shelf edge. Through time, as the shelf edge migrated seaward, deposition began with a turbidite channel dominated slope system (IQI 1 and 2) and progressed through a slump/debris flow dominated slope system (IQI 3,more » the principal reservoir) to a tide and wave dominated, collapsed shelf-edge deltaic system (IQI 4). Using seismic time slices and corresponding depositional facies in the core, a sandy {open_quotes}fairway{open_quotes} has been delineated in the IQI 3. Because of differences in stacking patterns of sandy and muddy slump intervals, seismic facies show: (1) both sheet-like and mounded external forms (geometries), and (2) parallel/continuous as well as chaotic/hummocky internal reflections. In wireline logs, slump facies exhibits blocky, coarsening-up, fining-up, and serrated motifs. In the absence of conventional core, slump facies may be misinterpreted and even miscorrelated because seismic facies and log motifs of slumps and debris flows tend to mimic properties of turbidite fan deposits. The slump dominated reservoir facies is composed of unconsolidated fine-grained sand. Thickness of individual units varies from 1 to 34 feet, but amalgamated intervals reach a thickness of up to 70 feet and apparently form connected sand bodies. Porosity commonly ranges from 20 to 35%. Horizontal permeability commonly ranges from 1,000 to 3,000 md.« less

Crustal structure and tectonic deformation of the southern Ecuadorian margin

NASA Astrophysics Data System (ADS)

Calahorrano, Alcinoe; Collot, Jean-Yves; Sage, Françoise; Ranero, César R.

2010-05-01

Multichannel seismic lines acquired during the SISTEUR cruise (2000) provide new constraints on the structure and deformation of the subduction zone at the southern Ecuadorian margin, from the deformation front to the continental shelf of the Gulf of Guayaquil. The pre-stack depth migrated images allows to characterise the main structures of the downgoing and overriding plates and to map the margin stratigraphy in order to propose a chronology of the deformation, by means of integrating commercial well data and industry seismic lines located in the gulf area. The 100-km-long seismic lines show the oceanic Nazca plate underthrusting the South American plate, as well as the subduction channel and inter-plate contact from the deformation front to about 90 km landward and ~20 km depth. Based on seismic structure we identify four upper-plate units, consisting of basement and overlaying sedimentary sequences A, B and C. The sedimentary cover varies along the margin, being few hundreds of meters thick in the lower and middle slope, and ~2-3 km thick in the upper slope. Exceptionally, a ~10-km -thick basin, here named Banco Peru basin, is located on the upper slope at the southernmost part of the gulf. This basin seems to be the first evidence of the Gulf of Guayaquil opening resulting from the NE escaping of the North Andean Block. Below the continental shelf, thick sedimentary basins of ~6 to 8 km occupy most of the gulf area. Tectonic deformation across most of the upper-plate is dominated by extensional regime, locally disturbed by diapirism. Compression evidences are restricted to the deformation front and surrounding areas. Well data calibrating the seismic profiles indicate that an important portion of the total thickness of the sedimentary coverage of the overriding plate are Miocene or older. The data indicate the extensional deformation resulting from the NE motion of the North Andean Block and the opening of the Gulf of Guayaquil, evolves progressively in age from the southern edge of the gulf near Banco Peru, where main subsidence seems to be Miocene or older, toward the northern limit, where high subsidence rates are early Pleistocene.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuo, Li-Jung; Lee, Chon-Lin; Louchouarn, Patrick

A 100-year history of human and natural disturbances in southwestern Taiwan was reconstructed using a suite of molecular markers in four dated sediment cores from the upper slope region off the Gaoping River mouth. Trends in polycyclic aromatic hydrocarbons (PAHs) tracked Taiwan's industrialization/urbanization starting in the 1970s, and the enactment of environmental regulatory policies thereafter.

Plant distribution-altitude and landform relationships in karstic sinkholes of Mediterranean region of Turkey.

PubMed

Ozkan, Kürsad; Gulsoy, Serkan; Mert, Ahmet; Ozturk, Munir; Muys, Bart

2010-01-01

The purpose of this study was to investigate the relationships between the plant distribution and the altitude-shape-size characteristics of sinkholes, and the landform characteristics inside sinkholes in the Mediterranean region of Turkey. Block kriging, Factor analysis, Cluster Analysis and Detrended Correspondence Analysis were performed. The sinkhole type and altitudinal zone were found to be the significant factors affecting the plant distribution. However, the sinkhole type was more important than the altitudinal zone. Hence, the sinkholes were first subdivided into groups according to types and then the groups were divided into subgroups according to the altitudinal zones. Consequently, 4 groups were defined; A-type sinkholes [1400-1550 m (A1), 1550-1700 m (A2)] and B-type sinkholes [1400-1550 (B1), 1550-1700 m (B2)]. The B-type was wider vertically and shorter horizontally than A-type sinkholes. Significant differences were found between the plant distribution and slope position inside the sinkholes. Plant distribution in the lower slopes was different from that in the flats and ridges in the B1 sub-type of B-type. Plant distribution in B2 subtype was different among the slope positions (ridge, middle slope, lower slope, and flat). Although distribution of plants is different in different parts (ridges, upper slope, middle slope, lower slope and basal flats) of A sinkhole, the differences between the parts of intermediate slope position are not significant. A high plant variability along short distances in the sinkholes was observed in the study area. That is why the site of sinkholes have a big potential for the distribution of many species. Hence, the area must be separated as strictly protected zone.

A soil catena on schist in northwestern California

USGS Publications Warehouse

Marron, D.C.; Popenoe, J.H.

1986-01-01

Soil characteristics in a small steepland watershed underlain by schist in a rainy, tectonically active area in northwestern California show close associations with drainage-basin position and slope characteristics. Five soil-topography units based on these associations are defined in the study watershed. Spatial relationships of soil series, and patterns of soil development as indicated by B-horizon clay content and redness, reflect interactions between pedogenesis and erosion. General soil-topography patterns include: (1) decreases in soil-development moving from low-order to higher-order stream vallyes; and (2) more developed soils on north-facing as opposed to south-facing slopes. Decreases in soil-profile development moving from slopes near low-order streams to slopes near higher-order streams approximately correlate with increases in gradient, vertical relief, and drainage density, and reflect a more vigorous stripping of regolith by erosion on the slopes near the higher-order streams. The larger percentage of area covered by the more developed soils on north-facing as opposed to south-facing slopes appears to reflect a contrast in the way dominant erosional processes interact with pedogenic processes. Roadcuts on middle and upper slopes show soil discontinuities indicative of disturbance by block slides or slumps or both. Roadcuts on lower slopes show disrupted soils in small bedrock hollows that could have been created by rapid, shallow landslides or by the pulled-up root wads of toppled trees. Soil-profile characteristics and soil-topography patterns in the study area demonstrate that both erosional and pedogenic processes need to be considered when interpreting characteristics of hillslope soils. ?? 1986.

Trunk and Shoulder Kinematic and Kinetic and Electromyographic Adaptations to Slope Increase during Motorized Treadmill Propulsion among Manual Wheelchair Users with a Spinal Cord Injury

PubMed Central

Champagne, Audrey

2015-01-01

The main objective was to quantify the effects of five different slopes on trunk and shoulder kinematics as well as shoulder kinetic and muscular demands during manual wheelchair (MWC) propulsion on a motorized treadmill. Eighteen participants with spinal cord injury propelled their MWC at a self-selected constant speed on a motorized treadmill set at different slopes (0°, 2.7°, 3.6°, 4.8°, and 7.1°). Trunk and upper limb movements were recorded with a motion analysis system. Net shoulder joint moments were computed with the forces applied to the handrims measured with an instrumented wheel. To quantify muscular demand, the electromyographic activity (EMG) of the pectoralis major (clavicular and sternal portions) and deltoid (anterior and posterior fibers) was recorded during the experimental tasks and normalized against maximum EMG values obtained during static contractions. Overall, forward trunk flexion and shoulder flexion increased as the slope became steeper, whereas shoulder flexion, adduction, and internal rotation moments along with the muscular demand also increased as the slope became steeper. The results confirm that forward trunk flexion and shoulder flexion movement amplitudes, along with shoulder mechanical and muscular demands, generally increase when the slope of the treadmill increases despite some similarities between the 2.7° to 3.6° and 3.6° to 4.8° slope increments. PMID:25793200

Trunk and shoulder kinematic and kinetic and electromyographic adaptations to slope increase during motorized treadmill propulsion among manual wheelchair users with a spinal cord injury.

PubMed

Gagnon, Dany; Babineau, Annie-Claude; Champagne, Audrey; Desroches, Guillaume; Aissaoui, Rachid

2015-01-01

The main objective was to quantify the effects of five different slopes on trunk and shoulder kinematics as well as shoulder kinetic and muscular demands during manual wheelchair (MWC) propulsion on a motorized treadmill. Eighteen participants with spinal cord injury propelled their MWC at a self-selected constant speed on a motorized treadmill set at different slopes (0°, 2.7°, 3.6°, 4.8°, and 7.1°). Trunk and upper limb movements were recorded with a motion analysis system. Net shoulder joint moments were computed with the forces applied to the handrims measured with an instrumented wheel. To quantify muscular demand, the electromyographic activity (EMG) of the pectoralis major (clavicular and sternal portions) and deltoid (anterior and posterior fibers) was recorded during the experimental tasks and normalized against maximum EMG values obtained during static contractions. Overall, forward trunk flexion and shoulder flexion increased as the slope became steeper, whereas shoulder flexion, adduction, and internal rotation moments along with the muscular demand also increased as the slope became steeper. The results confirm that forward trunk flexion and shoulder flexion movement amplitudes, along with shoulder mechanical and muscular demands, generally increase when the slope of the treadmill increases despite some similarities between the 2.7° to 3.6° and 3.6° to 4.8° slope increments.

Landslides caused by the Klamath Falls, Oregon, earthquakes of September 20, 1993

USGS Publications Warehouse

Keefer, D.K.; Schuster, R.L.

1993-01-01

In the Klamath Falls area, the most numerous earthquake-induced rock falls were along the east-to southeast-facing flank of a ridge immediately south and west of Howard Bay (locality 1 on the accompanying map), 18 km east-southeast of the epicenter of the magntiude 6.0 shock at 10:45 p.m. This ridge is more than 240 m high and has slopes steeper than 45° in places. The upper part of the ridge is composed of material from basaltic lava flows, an the lower slopes are covered with colluvium and talus deposits containing abundant boulders. 

CHANNEL EVOLUTION IN MODIFIED ALLUVIAL STREAMS.

USGS Publications Warehouse

Simon, Andrew; Hupp, Cliff R.

1987-01-01

This study (a) assesses the channel changes and network trends of bed level response after modifications between 1959 and 1972 of alluvial channels in western Tennessee and (b) develops a conceptual model of bank slope development to qualitatively assess bank stability and potential channel widening. A six-step, semiquantitative model of channel evolution in disturbed channels was developed by quantifying bed level trends and recognizing qualitative stages of bank slope development. Development of the bank profile is defined in terms of three dynamic and observable surfaces: (a) vertical face (70 to 90 degrees), (b) upper bank (25 to 50 degrees), and (c) slough line (20 to 25 degrees).

Seafloor Structural Geomorphic Evolution in Response to Seamount Subduction, Poverty Bay Indentation, New Zealand

NASA Astrophysics Data System (ADS)

Bodger, K. L.; Pettinga, J. R.; Barnes, P. M.

2006-12-01

More than 4000 km2 of high quality bathymetric and backscatter imaging of the Poverty Bay Indentation across the northern part of the Hikurangi subduction zone provide new insights into the relationship between seafloor morphology and active structures. The swath bathymetry extends from the edge of the continental shelf to the abyssal plain, at depths of between 100 to 3500 metres. The origin of the slope re-entrant is inferred to be related to multiple seamount impacts, and these collisions have initiated numerous large-scale gravitational collapse structures, multiple debris flow and avalanche deposits, which range in down-slope length from a few hundred metres to more than 40 km. The Poverty Bay Indentation has been simultaneously eroded by canyon systems that exhibit many of the features of incised river systems onshore. The swath images are complemented by the availability of excellent high-quality processed multi-channel seismic reflection data, single channel high-resolution 3.5 kHz seismic reflection data, as well as a limited number of core samples. Seismic reflection profiles and seafloor morphology are used to provide three morpho-structural sections. The comparison of these sections highlights the different effects of seamount subduction on the evolution of the margin and the re-entrant. The northern two sections are located to the north side of the re-entrant and reveal the role of seamount impact on the interrelationship between the structural evolution with respect to seafloor morphology. Here the development of an over-steepened margin with fault reactivation, inversion and over- printing leads to very complex structural styles of deformation and geometry in both seismic reflection profiles and seafloor morphology. There is evidence of an older, inactive thrust front buried beneath the upper and mid- slope basins. Beneath the mid-slope a subducted seamount is revealed by the presence of relief on the subduction interface and associated structural complexity in the over-riding wedge. The Poverty Bay canyon represents a structural transition zone coinciding with the re-entrant. The accretionary slope south of the re- entrant conforms more closely to the classic accretionary slope style of deformation. Backthrusts in this section propagate from a much shallower level than in the northern sections. Inversion is commonly observed in the mid slope and continental shelf basins, particularly to the south. Initial interpretations indicate that: i) seamount impact significantly influences the structural evolution, and submarine geomorphology of the inboard slope of the Hikurangi subduction zone, including the generation of large-scale gravitational collapse features; ii) the large gully systems located at the upper shelf slope boundary represent the most likely source areas for the multiple mega debris flows recognised from seafloor morphology and in seismic sections; iii) there exists a complex interaction between the evolving thrust-driven submarine ridges, ponded slope basins and the structural geometry and evolution of the near-surface fault zones (imbrication); iv) the submarine canyons may initiate complex patterns of fault zone segmentation and displacement transfer within the accretionary slope; and v) seamount subduction and subsequent instability of the margin may directly result in tsunami generation.

Nonmonotonic and spatial-temporal dynamic slope effects on soil erosion during rainfall-runoff processes

NASA Astrophysics Data System (ADS)

Wu, Songbai; Yu, Minghui; Chen, Li

2017-02-01

The slope effect on flow erosivity and soil erosion still remains a controversial issue. This theoretical framework explained and quantified the direct slope effect by coupling the modified Green-Ampt equation accounting for slope effect on infiltration, 1-D kinematic wave overland flow routing model, and WEPP soil erosion model. The flow velocity, runoff rate, shear stress, interrill, and rill erosion were calculated on 0°-60° isotropic slopes with equal horizontal projective length. The results show that, for short-duration rainfall events, the flow erosivity and erosion amounts exhibit a bell-shaped trend which first increase with slope gradient, and then decrease after a critical slope angle. The critical slope angles increase significantly or even vanish with increasing rainfall duration but are nearly independent of the slope projective length. The soil critical shear stress, rainfall intensity, and temporal patterns have great influences on the slope effect trend, while the other soil erosion parameters, soil type, hydraulic conductivity, and antecedent soil moisture have minor impacts. Neglecting the slope effect on infiltration would generate smaller erosion and reduce critical slope angles. The relative slope effect on soil erosion in physically based model WEPP was compared to those in the empirical models USLE and RUSLE. The trends of relative slope effect were found quite different, but the difference may diminish with increasing rainfall duration. Finally, relatively smaller critical slope angles could be obtained with the equal slope length and the range of variation provides a possible explanation for the different critical slope angles reported in previous studies.

Sequence stratigraphy of an Oligocene carbonate shelf, Central Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saller, A.; Armin, R.; Ichram, L.O.

1991-03-01

Interpretations of Oligocene shelfal limestones from Central Kalimantan, Indonesia, suggest caution in predicting sea-level lowstands from seismic reflector patterns or published sea-level curves. Three major depositional sequences, each 200-400 m thick, were delineated in outcrops and seismic lines: late Eocene to early Oligocene (34-38 Ma), middle Oligocene (29.7-32 Ma), and early late Oligocene (28-29.7 Ma). The lowest sequence is mainly shale with tin sandstones and limestones (large-foram wackestone). The middle and upper sequences are carbonate with transgressive systems tracts (TSTs) overlain by highstand systems tracts (HSTs). TSTs contain large-foram wackestone-packstones and coral wackestone-packstones. HSTs are characterized by (1) shale andmore » carbonate debris flows deposited on the lower slope, (2) argillaceous large-foram wackestones on the upper slope, (3) discontinuous coral wackestones and boundstones on the shelf margin, (4) bioclastic packstones and grainstones on backreef flats and shelf-margin shoals, and (5) branching-coral and foraminiferal wackestones in the lagoon. Bases of sequences are characterized by transgression and onlap. Deepending and/or drowning of the carbonate shelf occurred at the top of the middle and upper sequences. Basinal strata that apparently onlap the middle and upper carbonate shelf margins might be misinterpreted as lowstand deposits, although regional studies indicate they are prodelta sediments baselapping against the shelf. Shallowing the subaerial exposure of the carbonates might be expected during the large mid-Oligocene (29.5-30 Ma) sea-level drop of Haq et al. (1987), instead of the observed deepening and local drowning.« less

Multi-year Current Observations on the Shelf Slope off Cape Hatteras, NC

NASA Astrophysics Data System (ADS)

Muglia, M.

2017-12-01

As part of an observing and modeling effort by the North Carolina Renewable Ocean Energy Program to determine if the Gulf Stream is a viable marine hydrokinetic energy resource for the state, upper continental slope current measurements were made over a period of nearly four years off of Cape Hatteras, NC. Velocity profiles were measured by a near-bottom, upward-looking, 150-kHz Acoustic Doppler Current Profiler deployed at a depth of 230-260 m. The mooring was sited at the location where water from the Gulf Stream, Middle Atlantic Bight, South Atlantic Bight, and Slope Sea all converge. Measured tidal amplitudes here are 2 m. These observations are used to consider the temporal variability and vertical structure of the currents at this location at tidal to interannual periods at this complex location. Concurrent near-bottom water mass properties are considered.

Have a Nice Spring! MOC Revisits "Happy Face" Crater

NASA Image and Video Library

2005-05-16

Smile! Spring has sprung in the martian southern hemisphere. With it comes the annual retreat of the winter polar frost cap. This view of "Happy Face Crater"--officially named "Galle Crater"--shows patches of white water ice frost in and around the crater's south-facing slopes. Slopes that face south will retain frost longer than north-facing slopes because they do not receive as much sunlight in early spring. This picture is a composite of images taken by the Mars Global Surveyor Mars Orbiter Camera (MOC) red and blue wide angle cameras. The wide angle cameras were designed to monitor the changing weather, frost, and wind patterns on Mars. Galle Crater is located on the east rim of the Argyre Basin and is about 215 kilometers (134 miles) across. In this picture, illumination is from the upper left and north is up. http://photojournal.jpl.nasa.gov/catalog/PIA02325

Frosty Gullies on the Northern Plains

NASA Image and Video Library

2015-07-15

Seasonal frost commonly forms at middle and high latitudes on Mars, much like winter snow on Earth. However, on Mars most frost is carbon dioxide dry ice rather than water ice. This image is from NASA Mars Reconnaissance Orbiter. This image shows frost in gully alcoves in a crater on the Northern plains. The frost highlights details of the alcoves, since it forms in different amounts depending on slopes and shadows as well as the type of material making up the ground. Rugged rock outcrops appear dark and shadowed, while frost highlights the upper alcove and the steepest route down the slope. Most changes associated with gullies are observed in the Southern hemisphere. However, some are seen in the Northern hemisphere, where steep slopes are less common. HiRISE is monitoring these gullies to look for changes and to understand the behavior of the frost. http://photojournal.jpl.nasa.gov/catalog/PIA19852

Potential Risk Assessment of Mountain Torrent Disasters on Sloping Fields in China

NASA Astrophysics Data System (ADS)

GAO, X.

2017-12-01

China's sloping fields have the problems of low production and serious soil erosion, and mountain torrent disasters will bring more serious soil and water loss to traditional extensive exploitation of sloping field resources. In this paper, China's sloping fields were classified into three grades, such as slightly steep, steep and very steep grade. According to the geological hazards prevention and control regulation, the historical data of China's mountain torrent disasters were spatially interpolated and divided into five classes, such as extremely low, low, middle, high and extremely high level. And the risk level map of mountain torrents was finished in ArcGIS. By using overlaying analysis on sloping fields and risk level map, the potential risk regionalization map of sloping fields in various slope grades was obtained finally. The results shows that the very steep and steep sloping fields are mainly distributed in the first or second stage terraces in China. With the increase of hazard risk level, the area of sloping fields decreases rapidly and the sloping fields in extremely low and low risk levels of mountain torrents reach 98.9%. With the increase of slope grade, the area of sloping fields in various risk levels also declines sharply. The sloping fields take up approximately 60 65% and 26 30% in slightly steep and steep grade areas separately at different risk level. The risk regionalization map can provide effective information for returning farmland to forests or grassland and reducing water and soil erosion of sloping fields in the future.

Variations in Soil Properties and Herbicide Sorption Coefficients with Depth in Relation to PRZM (Pesticide Root Zone Model) Calculations

USDA-ARS?s Scientific Manuscript database

There are few experimental data available on how herbicide sorption coefficients change across small increments within soil profiles. Soil profiles were obtained from three landform elements (eroded upper slope, deposition zone, and eroded waterway) in a strongly eroded agricultural field and segmen...

Investigating Graphical Representations of Slope and Derivative without a Physics Context

ERIC Educational Resources Information Center

Christensen, Warren M.; Thompson, John R.

2012-01-01

By analysis of student use of mathematics in responses to conceptual physics questions, as well as analogous math questions stripped of physical meaning, we have previously found evidence that students often enter upper-level physics courses lacking the assumed prerequisite mathematics knowledge and/or the ability to apply it productively in a…

Effects of a Community Restoration Fire on Small Mammals and Herpetofauna in the Southern Appalachains

Treesearch

William M. Ford; M. Alex Menzel; David W. McGill; Joshua Laerm; Timothy S. McCay

1999-01-01

As part of the Wine Spring Creek ecosystem management project on the Nantahala National forest, North Carolina, we assessed effects of a community restoration fire on small mammals and herpetofauna in the upper slope pitch pine (Pinus rigida) stands, neighboring midslope oak (Quercus spp.) stands and rhododendron (...

Heart-rot hazard is low in Abies amabilis reproduction injured by logging.

Treesearch

Paul E. Aho

1960-01-01

Clear-cut units in upper-slope forest types in western Washington and Oregon often have an understory of Pacific silver fir (Abies amabilis) at time of logging. Foresters sometimes hesitate to preserve this advance regeneration, partly because of the possibility that heart rots infecting through logging wounds might considerably reduce the...

Characteristics, histories, and future succession of northern Pinus pugens stands

Treesearch

Patrick Brose

2017-01-01

Pinus pungens (Table Mountain pine) stands are rare conifer-dominated communities that occur on xeric ridges and upper slopes throughout the central and southern Appalachian Mountains. At the northern end of this range, this uncommon forest community is essentially unstudied. Therefore, in 2006 I initiated a dendroecology study of three ...

Species-site relationships in a Northern Arkansas upland forest

Treesearch

Eric Heitzman; Michael G. Shelton; Ruth Ann Chapman

2006-01-01

Phytosociological aspects of the forest vegetation were described for a 780-ha area on the Sylamore Experimental Forest in northern Arkansas. Pronounced changes in species composition occurred with topographic position in this deeply dissected area. For the overstory, oaks and pines dominated the upper slope positions, while other tree species dominated the lower...

4. LOWER NOTTINGHAM MINE. DETAIL OF OBJECTS ASSOCIATED WITH CABIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. LOWER NOTTINGHAM MINE. DETAIL OF OBJECTS ASSOCIATED WITH CABIN 'B'; PIPE, WOOD, STOVE MATERIALS, AND COLLAPSED ROOT CELLAR IN CENTRAL AREA. VERTICAL, DARK PIPE IS VISIBLE IN CENTER/UPPER THIRD. CAMERA POINTED EAST. - Florida Mountain Mining Sites, Lower Nottingham Mine, Western slope of Florida Mountain, Silver City, Owyhee County, ID

Analysis of select facial and dental esthetic parameters.

PubMed

Nold, Sarah L; Horvath, Sebastian D; Stampf, Susanne; Blatz, Markus B

2014-01-01

This clinical study examined objective smile parameters in the natural anterior dentition. Standardized intraoral and extraoral photographs were taken of 106 Caucasian adults (54 women, 52 men) with a healthy dentition. The following parameters were analyzed: correlation of dental and facial midline, upper lip position and curvature, relationship of the maxillary anterior incisal curve with lower lip, number of teeth displayed in a smile, distance between maxillary anterior teeth and lower lip, slope of tooth, and lip arc. The simple frequency distribution of measured variables revealed an average smile with coinciding dental and facial midlines, an average smile line, and a straight upper lip curvature. With an average smile, the maxillary anterior teeth did not touch the lower lip, teeth were displayed up to the second premolar, and the maxillary anterior incisal curve was parallel to the lower lip. Oval was the most prevalent tooth form. A slope of 9 degrees was detected for the mean tooth arc and 13 degrees for the mean lip arc. The outcomes of this clinical study provide a quantifiable frame for esthetic evaluation, treatment planning, and restoration fabrication.

Supercritical bedforms and sedimentary structures from field and core studies, Middle Eocene deep-marine base-of-slope environment, Ainsa Basin, Spanish Pyrenees

NASA Astrophysics Data System (ADS)

Cornard, Pauline; Pickering, Kevin

2017-04-01

In recent years, many researchers have focussed on supercritical- and subcritical-flow deposits using flume-tank experiments (e.g., Cartigny el al., 2011; Postma et al., 2014; Postma and Cartigny, 2014), or from direct observations on presently active deep-water systems (e.g., Hughes et al., 2012). Using outcrop and core examples from a base-of-slope environment in the Middle Eocene Ainsa Basin, Spanish Pyrenees, and with published experimental work, a range of deposits are interpreted as upper-flow regime sedimentary structures. This contribution focusses on the interpretation of several supercritical bedforms (antidunes and chutes-and-pools) observed on the field and upper-flow regime sedimentary structures recognized in cores. The spatial distribution of supercritical-flow deposits obtained from an analysis of field outcrops and core sedimentary logs are evaluated in relation to the depositional environment (channel axis, off-axis, margin and interfan). The frequency distributions of the bed thicknesses are also analysed in relation to supercritical versus subcritical bed-thickness distributions.

Spline based least squares integration for two-dimensional shape or wavefront reconstruction

DOE PAGES

Huang, Lei; Xue, Junpeng; Gao, Bo; ...

2016-12-21

In this paper, we present a novel method to handle two-dimensional shape or wavefront reconstruction from its slopes. The proposed integration method employs splines to fit the measured slope data with piecewise polynomials and uses the analytical polynomial functions to represent the height changes in a lateral spacing with the pre-determined spline coefficients. The linear least squares method is applied to estimate the height or wavefront as a final result. Numerical simulations verify that the proposed method has less algorithm errors than two other existing methods used for comparison. Especially at the boundaries, the proposed method has better performance. Themore » noise influence is studied by adding white Gaussian noise to the slope data. Finally, experimental data from phase measuring deflectometry are tested to demonstrate the feasibility of the new method in a practical measurement.« less

Spline based least squares integration for two-dimensional shape or wavefront reconstruction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Lei; Xue, Junpeng; Gao, Bo

In this paper, we present a novel method to handle two-dimensional shape or wavefront reconstruction from its slopes. The proposed integration method employs splines to fit the measured slope data with piecewise polynomials and uses the analytical polynomial functions to represent the height changes in a lateral spacing with the pre-determined spline coefficients. The linear least squares method is applied to estimate the height or wavefront as a final result. Numerical simulations verify that the proposed method has less algorithm errors than two other existing methods used for comparison. Especially at the boundaries, the proposed method has better performance. Themore » noise influence is studied by adding white Gaussian noise to the slope data. Finally, experimental data from phase measuring deflectometry are tested to demonstrate the feasibility of the new method in a practical measurement.« less

Sedimentary response to ice stream advance and retreat on the Storfjorden Trough Mouth Fan (NW Barents Sea), during Late Weichselian

NASA Astrophysics Data System (ADS)

Pedrosa, Mayte; Camerlengui, Angelo; de Mol, Ben; Lucchi, Renata. G.; Úrgeles, Roger; Rebesco, Michele; Winsborrow, Monica; Laberg, Jan. S.; Andreassen, Karin; Accettella, Daniela

2010-05-01

This seafloor morphological study of the Storfjorden Trough Mouth Fan (TMF) (offshore Svalbard, NW Barents Sea) is based on new multibeam bathymetry and chirp sub-bottom profiler data acquired in 2007 during the BIO Hespérides cruise SVAIS that provides an unprecedented image of the sedimentary processes that accompanied the last advance and retreat of the Storfjorden Ice Stream. Compared to other glacial-marine sedimentary systems (such as the adjacent Bjørnøyrenna TMF), the Storfjorden TMF system is small and associated to a relatively small terrestrial ice sheet, approximately 40.000 km2, with local provenance from Svalbard and the Spitsbergen Bank. Due to this short distance from the ice source to the calving areas and the resulting short residence time of ice in the ice sheet, therefore the glacio -marine system of the Storfjorden reacts rapidly to climatic changes. The Storfjorden continental slope is characterized by three depositional lobes, produced by focused sedimentation at the terminus of ice streams that have changed their location with time. The superficial morphology features associated to the two northernmost lobes are straight gullies in the upper slope, and debris lobes starting from the midslope onwards. The seafloor expression of the southernmost lobe, adjacent to the much smaller Kveithola TMF, demonstrate almost no gully incisions and is dominated by the widespread occurrence of small-scale submarine landslides. The subbottom profiles illustrate that sediment failures occurred throughout the Late Neogene evolution of the southern Storfjorden and Kveithola margin, including large-scale mass transport deposits of up to 200 m thick. Seismic facies of the Neogene sequence shows an alternation of glacigenic debris flows and laminated sediment drape inferred to be plumites. Gullies incising glacigenic debris flows at the surface and subsurface and are filled by an interglacial drape sequence. The gullies are formed during each deglaciation phase, most likely by the erosive action of short-lived high density currents originated by sediment-loaded subglacial melt water discharge.At the outer continental shelf of the southernmost lobe a striking fresh linear straight, which has a width of 1, 5 kilometres and cut the morainal deposits. These features are interpreted as mega-scale glacial lineations, which are tentatively attributed to mega-iceberg scours. These lineations are witness the latest advances of the Storfjorden ice streams before the final retreat which was located at the southernmost lobe. One of the main pre-conditioning factors to slope instability on the southern part of the Storfjorden TMF is identified as high sedimentation rate plumites deposited on the middle-upper continental slope by glacial melt water plumes. This study is part of the SVAIS project (funded by the Spanish IPY), that has a main objective to improve the understanding and the relationship between sedimentation and ice sheet dynamics under natural climatic changes.

Relative contributions of wind and water erosion to total soil loss and its effect on soil properties in sloping croplands of the Chinese Loess Plateau.

PubMed

Tuo, Dengfeng; Xu, Mingxiang; Gao, Guangyao

2018-08-15

Wind and water erosion are two dominant types of erosion that lead to soil and nutrient losses. Wind and water erosion may occur simultaneously to varying extents in semi-arid regions. The contributions of wind and water erosion to total erosion and their effects on soil quality, however, remains elusive. We used cesium-137 ( 137 Cs) inventories to estimate the total soil erosion and used the Revised Universal Soil Loss Equation (RUSLE) to quantify water erosion in sloping croplands. Wind erosion was estimated from the subtraction of the two. We also used 137 Cs inventories to calculate total soil erosion and validate the relationships of the soil quality and erosion at different slope aspects and positions. The results showed that wind erosion (1460tkm -2 a -1 ) on northwest-facing slope was responsible for approximately 39.7% of the total soil loss, and water erosion (2216tkm -2 a -1 ) accounted for approximately 60.3%. The erosion rates were 58.8% higher on northwest- than on southeast-facing slopes. Northwest-facing slopes had lower soil organic carbon, total nitrogen, clay, and silt contents than southeast-facing slopes, and thus, the 137 Cs inventories were lower, and the total soil erosions were higher on the northwest-facing slopes. The variations in soil physicochemical properties were related to total soil erosion. The lowest 137 Cs inventories and nutrient contents were recorded at the upper positions on the northwest-facing slopes due to the successive occurrence of more severe wind and water erosion at the same site. The results indicated that wind and water could accelerate the spatial variability of erosion rate and soil properties and cause serious decreases in the nutrient contents in sloping fields. Our research could help researchers develop soil strategies to reduce soil erosion according to the dominant erosion type when it occurs in a hilly agricultural area. Copyright © 2018 Elsevier B.V. All rights reserved.

Observational study of surface wind along a sloping surface over mountainous terrain during winter

NASA Astrophysics Data System (ADS)

Lee, Young-Hee; Lee, Gyuwon; Joo, Sangwon; Ahn, Kwang-Deuk

2018-03-01

The 2018 Winter Olympic and Paralympic Games will be held in Pyeongchang, Korea, during February and March. We examined the near surface winds and wind gusts along the sloping surface at two outdoor venues in Pyeongchang during February and March using surface wind data. The outdoor venues are located in a complex, mountainous terrain, and hence the near-surface winds form intricate patterns due to the interplay between large-scale and locally forced winds. During February and March, the dominant wind at the ridge level is westerly; however, a significant wind direction change is observed along the sloping surface at the venues. The winds on the sloping surface are also influenced by thermal forcing, showing increased upslope flow during daytime. When neutral air flows over the hill, the windward and leeward flows show a significantly different behavior. A higher correlation of the wind speed between upper- and lower-level stations is shown in the windward region compared with the leeward region. The strong synoptic wind, small width of the ridge, and steep leeward ridge slope angle provide favorable conditions for flow separation at the leeward foot of the ridge. The gust factor increases with decreasing surface elevation and is larger during daytime than nighttime. A significantly large gust factor is also observed in the leeward region.

Crust-core properties of neutron stars in the Nambu–Jona-Lasinio model

NASA Astrophysics Data System (ADS)

Wei, Si-Na; Yang, Rong-Yao; Jiang, Wei-Zhou

2018-05-01

We adopt the Nambu–Jona-Lasinio (NJL) model to study the crust-core transition properties in neutron stars (NSs). For a given momentum cutoff and symmetry energy of saturation density in the NJL model, decreasing the slope of the symmetry energy gives rise to an increase in the crust-core transition density and transition pressure. Given the slope of the symmetry energy at saturation density, the transition density and corresponding transition pressure increase with increasing symmetry energy. The increasing trend between the fraction of the crustal moment of inertia and the slope of symmetry energy at saturation density indicates that a relatively large momentum cutoff of the NJL model is preferred. For a momentum cutoff of 500 MeV, the fraction of the crustal moment of inertia clearly increases with the slope of symmetry energy at saturation density. Thus, at the required fraction (7%) of the crustal moment of inertia, the NJL model with momentum cutoff of 500 MeV and a large slope of the symmetry energy of saturation density can give the upper limit of the mass of the Vela pulsar to be above 1.40 {M}ȯ . Supported by National Natural Science Foundation of China (11775049, 11275048) and the China Jiangsu Provincial Natural Science Foundation (BK20131286)

An optimal proportion of mixing broad-leaved forest for enhancing the effective productivity of moso bamboo.

PubMed

Cheng, Xiao-Fei; Shi, Pei-Jian; Hui, Cang; Wang, Fu-Sheng; Liu, Guo-Hua; Li, Bai-Lian

2015-04-01

Moso bamboos (Phyllostachys edulis) are important forestry plants in southern China, with substantial roles to play in regional economic and ecological systems. Mixing broad-leaved forests and moso bamboos is a common management practice in China, and it is fundamental to elucidate the interactions between broad-leaved trees and moso bamboos for ensuring the sustainable provision of ecosystem services. We examine how the proportion of broad-leaved forest in a mixed managed zone, topology, and soil profile affects the effective productivity of moso bamboos (i.e., those with significant economic value), using linear regression and generalized additive models. Bamboo's diameter at breast height follows a Weibull distribution. The importance of these variables to bamboo productivity is, respectively, slope (25.9%), the proportion of broad-leaved forest (24.8%), elevation (23.3%), gravel content by volume (16.6%), slope location (8.3%), and soil layer thickness (1.2%). Highest productivity is found on the 25° slope, with a 600-m elevation, and 30% broad-leaved forest. As such, broad-leaved forest in the upper slope can have a strong influence on the effective productivity of moso bamboo, ranking only after slope and before elevation. These factors can be considered in future management practice.

An introductory review on gravitational-deformation induced structures, fabrics and modeling

NASA Astrophysics Data System (ADS)

Jaboyedoff, Michel; Penna, Ivanna; Pedrazzini, Andrea; Baroň, Ivo; Crosta, Giovanni B.

2013-10-01

Recent studies have pointed out a similarity between tectonics and slope tectonic-induced structures. Numerous studies have demonstrated that structures and fabrics previously interpreted as of purely geodynamical origin are instead the result of large slope deformation, and this led in the past to erroneous interpretations. Nevertheless, their limit seems not clearly defined, but it is somehow transitional. Some studies point out continuity between failures developing at surface with upper crust movements. In this contribution, the main studies which examine the link between rock structures and slope movements are reviewed. The aspects regarding model and scale of observation are discussed together with the role of pre-existing weaknesses in the rock mass. As slope failures can develop through progressive failure, structures and their changes in time and space can be recognized. Furthermore, recognition of the origin of these structures can help in avoiding misinterpretations of regional geology. This also suggests the importance of integrating different slope movement classifications based on distribution and pattern of deformation and the application of structural geology techniques. A structural geology approach in the landslide community is a tool that can greatly support the hazard quantification and related risks, because most of the physical parameters, which are used for landslide modeling, are derived from geotechnical tests or the emerging geophysical approaches.

Small-Maturity Asymptotics for the At-The-Money Implied Volatility Slope in Lévy Models

PubMed Central

Gerhold, Stefan; Gülüm, I. Cetin; Pinter, Arpad

2016-01-01

ABSTRACT We consider the at-the-money (ATM) strike derivative of implied volatility as the maturity tends to zero. Our main results quantify the behaviour of the slope for infinite activity exponential Lévy models including a Brownian component. As auxiliary results, we obtain asymptotic expansions of short maturity ATM digital call options, using Mellin transform asymptotics. Finally, we discuss when the ATM slope is consistent with the steepness of the smile wings, as given by Lee’s moment formula. PMID:27660537

Facies Analysis and Depositional environment of the Oligocene-Miocene Qom Formation in the Central Iran (Semnan area)

NASA Astrophysics Data System (ADS)

Sabouhi, Mostafa; Sheykh, Morteza; Darvish, Zohreh; Naghavi Azad, Maral

2010-05-01

The Qom formation was formed in the Oligo-Miocene during the final sea transgression in Central Iran. This Formation in the Central Iran Basin Contains oil and gas. Organic geochemical analysis in previous studies indicated that the hydrocarbons migrated from deeper source rocks, likely of Jurassic age. In the Central Iran Basin, the Qom Formation is 1,200m thick and is abounded by the Oligocene Lower Red Formation and the middle Miocene Upper Red Formation. In previous studies, the Qom Formation was divided into nine members designated from oldest to youngest: a, b, c1 to c4, d, e, and f, of which "e" is 300m thick and constitutes the main reservoir. Our study focused on a Qom Section located in the Arvaneh (Semnan) region of Central Iran that is 498m thick. The lower part of the formation was not deposited, and only the following four members of early Miocene age (Aquitanian-Burdigalian) was identified between the lower and upper Red Formation. The studied section mainly consist of limestone, marl, sandy limestone, sandy marl and argillaceous limestone.According to this study(field and laboratory investigations), 9 carbonate microfacies were recognized which are grouped into four facies associations (microfacies group). These facies associations present platform to basin depositional setting and are nominated as: A (Tidal-flat), B (Lagoon), C (Slope) and D (Open marine). Based on paleoecology and Petrographic analysis, it seems the Qom Formation was deposited in a Carbonate shelf setting. The Qom formation constitutes a regional transgressive-regressive sequence that is bounded by two continental units (Lower and Upper Red Formation).

Preliminary Tectonic Subsidence Results: Outer Shelf and Upper Slope Sites, Canterbury Basin from IODP Expedition 317

NASA Astrophysics Data System (ADS)

Kominz, M. A.; Expedition 317 Shipboard Scientific Party

2010-12-01

Integrated Ocean Drilling Program (IODP) Expedition 317 drilled four sites, generating a transect from the shelf to the upper slope of the Canterbury Basin, South Island, New Zealand. One of the primary goals of the expedition was to determine the magnitude and timing of sea level change using backstripping analysis. Integration of moisture and density (MAD) data, smear slide data, lithologic descriptions, carbonate analyses, age estimates and benthic foraminiferal estimates of water depths from shipboard results provides a preliminary database for backstripping Site U1351 on the mid to outer shelf and Site U1352 on the upper slope. These boreholes penetrated to about 10 Ma and 35 Ma, respectively. In these preliminary analyses, older sediment thicknesses, ages and water depths were taken from the nearby industry Clipper-1 well. In the absence of water depth corrections, the two IODP sites and the Clipper-1 well show an increase in subsidence rate beginning 15 to 8 Ma and continuing to the present. The water depths observed in Clipper-1 shoal slightly through this time, reducing the magnitude of the subsidence event. Tectonics seem to have been more active at the two IODP sites. Both show significant tectonic uplift of at least 300 to 400 meters between about 6.5 and 4.5 Ma, after which, they follow the general, trend of rapid subsidence observed at the Clipper-1 well. Additionally, our oldest dataset (Site U1352) shows a large tectonic uplift event of at least 2000 m that occurred between 17.5 and 11 Ma. Higher frequency variations are superimposed on the long-term trends at both IODP sites. These fluctuations are most likely due to glacioeustasy. The magnitudes of these events are higher than those observed through other proxies. It is likely that data refinement in onshore studies will be able to resolve this issue.

Significant strain accumulation between the deformation front and landward out-of-sequence thrusts in accretionary wedge of SW Taiwan revealed by cGPS and SAR interferometry

NASA Astrophysics Data System (ADS)

Tsai, M. C.

2017-12-01

High strain accumulation across the fold-and-thrust belt in Southwestern Taiwan are revealed by the Continuous GPS (cGPS) and SAR interferometry. This high strain is generally accommodated by the major active structures in fold-and-thrust belt of western Foothills in SW Taiwan connected to the accretionary wedge in the incipient are-continent collision zone. The active structures across the high strain accumulation include the deformation front around the Tainan Tableland, the Hochiali, Hsiaokangshan, Fangshan and Chishan faults. Among these active structures, the deformation pattern revealed from cGPS and SAR interferometry suggest that the Fangshan transfer fault may be a left-lateral fault zone with thrust component accommodating the westward differential motion of thrust sheets on both side of the fault. In addition, the Chishan fault connected to the splay fault bordering the lower-slope and upper-slope of the accretionary wedge which could be the major seismogenic fault and an out-of-sequence thrust fault in SW Taiwan. The big earthquakes resulted from the reactivation of out-of-sequence thrusts have been observed along the Nankai accretionary wedge, thus the assessment of the major seismogenic structures by strain accumulation between the frontal décollement and out-of-sequence thrusts is a crucial topic. According to the background seismicity, the low seismicity and mid-crust to mantle events are observed inland and the lower- and upper- slope domain offshore SW Taiwan, which rheologically implies the upper crust of the accretionary wedge is more or less aseimic. This result may suggest that the excess fluid pressure from the accretionary wedge not only has significantly weakened the prism materials as well as major fault zone, but also makes the accretionary wedge landward extension, which is why the low seismicity is observed in SW Taiwan area. Key words: Continuous GPS, SAR interferometry, strain rate, out-of-sequence thrust.

Brittle and Ductile Behavior in Deep-Seated Landslides: Learning from the Vajont Experience

NASA Astrophysics Data System (ADS)

Paronuzzi, Paolo; Bolla, Alberto; Rigo, Elia

2016-06-01

This paper analyzes the mechanical behavior of the unstable Mt. Toc slope before the 1963 catastrophic collapse, considering both the measured data (surface displacements and microseismicity) and the updated geological model of the prehistoric rockslide. From February 1960 up to 9 October 1963, the unstable mass behaved as a brittle-ductile `mechanical system,' characterized by remarkable microseismicity as well as by considerable surface displacements (up to 4-5 m). Recorded microshocks were the result of progressive rock fracturing of distinct resisting stiff parts made up of intact rock (indentations, undulations, and rock bridges). The main resisting stiff part was a large rock indentation located at the NE extremity of the unstable mass that acted as a mechanical constraint during the whole 1960-1963 period, inducing a progressive rototranslation toward the NE. This large constraint failed in autumn 1960, when an overall slope failure took place, as emphasized by the occurrence of the large perimetrical crack in the upper slope. In this circumstance, the collapse was inhibited by a reblocking phenomenon of the unstable mass that had been previously destabilized by the first reservoir filling. Progressive failure of localized intact rock parts progressively propagated westwards as a consequence of the two further filling-drawdown cycles of the reservoir (1962 and 1963). The characteristic brittle-ductile behavior of the Vajont landslide was made possible by the presence of a very thick (40-50 m) and highly deformable shear zone underlying the upper rigid rock mass (100-120 m thick).

Long-term responses of rainforest erosional systems at different spatial scales to selective logging and climatic change

PubMed Central

Walsh, R. P. D.; Bidin, K.; Blake, W. H.; Chappell, N. A.; Clarke, M. A.; Douglas, I.; Ghazali, R.; Sayer, A. M.; Suhaimi, J.; Tych, W.; Annammala, K. V.

2011-01-01

Long-term (21–30 years) erosional responses of rainforest terrain in the Upper Segama catchment, Sabah, to selective logging are assessed at slope, small and large catchment scales. In the 0.44 km2 Baru catchment, slope erosion measurements over 1990–2010 and sediment fingerprinting indicate that sediment sources 21 years after logging in 1989 are mainly road-linked, including fresh landslips and gullying of scars and toe deposits of 1994–1996 landslides. Analysis and modelling of 5–15 min stream-suspended sediment and discharge data demonstrate a reduction in storm-sediment response between 1996 and 2009, but not yet to pre-logging levels. An unmixing model using bed-sediment geochemical data indicates that 49 per cent of the 216 t km−2 a−1 2009 sediment yield comes from 10 per cent of its area affected by road-linked landslides. Fallout 210Pb and 137Cs values from a lateral bench core indicate that sedimentation rates in the 721 km2 Upper Segama catchment less than doubled with initially highly selective, low-slope logging in the 1980s, but rose 7–13 times when steep terrain was logged in 1992–1993 and 1999–2000. The need to keep steeplands under forest is emphasized if landsliding associated with current and predicted rises in extreme rainstorm magnitude-frequency is to be reduced in scale. PMID:22006973

Fire coral clones demonstrate phenotypic plasticity among reef habitats.

PubMed

Dubé, Caroline E; Boissin, Emilie; Maynard, Jeffrey A; Planes, Serge

2017-08-01

Clonal populations are often characterized by reduced levels of genotypic diversity, which can translate into lower numbers of functional phenotypes, both of which impede adaptation. Study of partially clonal animals enables examination of the environmental settings under which clonal reproduction is favoured. Here, we gathered genotypic and phenotypic information from 3,651 georeferenced colonies of the fire coral Millepora platyphylla in five habitats with different hydrodynamic regimes in Moorea, French Polynesia. In the upper slope where waves break, most colonies grew as vertical sheets ("sheet tree") making them more vulnerable to fragmentation. Nearly all fire corals in the other habitats are encrusting or massive. The M. platyphylla population is highly clonal (80% of the colonies are clones), while characterized by the highest genotype diversity ever documented for terrestrial or marine populations (1,064 genotypes). The proportion of clones varies greatly among habitats (≥58%-97%) and clones (328 clonal lineages) are distributed perpendicularly from the reef crest, perfectly aligned with wave energy. There are six clonal lineages with clones dispersed in at least two adjacent habitats that strongly demonstrate phenotypic plasticity. Eighty per cent of the colonies in these lineages are "sheet tree" on the upper slope, while 80%-100% are encrusting or massive on the mid slope and back reef. This is a unique example of phenotypic plasticity among reef-building coral clones as corals typically have wave-tolerant growth forms in high-energy reef areas. © 2017 John Wiley & Sons Ltd.

On the morphometry of terrestrial shield volcanoes

NASA Astrophysics Data System (ADS)

Grosse, Pablo; Kervyn, Matthieu

2016-04-01

Shield volcanoes are described as low angle edifices that have convex up topographic profiles and are built primarily by the accumulation of lava flows. This generic view of shields' morphology is based on a limited number of monogenetic shields from Iceland and Mexico, and a small set of large oceanic islands (Hawaii, Galapagos). Here, the morphometry of over 150 monogenetic and polygenetic shield volcanoes, identified inthe Global Volcanism Network database, are analysed quantitatively from 90-meter resolution DEMs using the MORVOLC algorithm. An additional set of 20 volcanoes identified as stratovolcanoes but having low slopes and being dominantly built up by accumulation of lava flows are documented for comparison. Results show that there is a large variation in shield size (volumes range from 0.1 to >1000 km3), profile shape (height/basal width ratios range from 0.01 to 0.1), flank slope gradients, elongation and summit truncation. Correlation and principal component analysis of the obtained quantitative database enables to identify 4 key morphometric descriptors: size, steepness, plan shape and truncation. Using these descriptors through clustering analysis, a new classification scheme is proposed. It highlights the control of the magma feeding system - either central, along a linear structure, or spatially diffuse - on the resulting shield volcano morphology. Genetic relationships and evolutionary trends between contrasted morphological end-members can be highlighted within this new scheme. Additional findings are that the Galapagos-type morphology with a central deep caldera and steep upper flanks are characteristic of other shields. A series of large oceanic shields have slopes systematically much steeper than the low gradients (<4-8°) generally attributed to large Hawaiian-type shields. Finally, the continuum of morphologies from flat shields to steeper complex volcanic constructs considered as stratovolcanoes calls for a revision of this oversimplified distinction, taking into account the lava/pyroclasts ratio and the spatial distribution of eruptive vents.

On the reintroduction of the endangered thick-shelled river mussel Unio crassus: The importance of the river's longitudinal profile.

PubMed

Zając, Katarzyna; Florek, Jacek; Zając, Tadeusz; Adamski, Paweł; Bielański, Wojciech; Ćmiel, Adam M; Klich, Mariusz; Lipińska, Anna M

2018-05-15

Freshwater mussels of the order Unionida provide important ecosystem functions and services. Unfortunately, some previously widespread species are now seriously endangered. To restore the historical range of the population of Unio crassus in the Biała River, southern Poland, the species was reintroduced into a series of 'stepping stones' joining two remnant populations. During the first phase of the study, the relationships between the abundance of U. crassus, physical habitat, and water quality were studied to assess reintroduction potential. In general, chemical water quality improved upstream from the existing population, favouring the decision for reintroduction, whereas morphological variables worsened. Mussel abundance was correlated negatively with the elevation and slope of channel, organic matter contents, and pH (exceeding 8.0), but positively with silt presence, water conductivity, and concentrations of HCO 3 - , Ca 2+ , and NO 3 - . During the second phase, adult individuals were introduced into one type of functional habitat-marginal channel sectors with still water and fine sediment. Despite the initial very high rate of reproduction in some parts of the upper reach of the river, the juveniles were ultimately recruited only in the lower part of the restored range, resulting in a very rapid change in recruitment at a channel slope of 1.8‰. Recruitment was positively related to silt content, conductivity, and Ca 2+ and HCO 3 - ions, negatively to channel elevation and slope, and water pH. The host fish species showed no correlation with abiotic habitat features within the studied reach. These results imply that most of the habitat traits related to U. crassus occurrence depended on the river's longitudinal profile, not on the chemical water quality, and that final success of introduction should be evaluated after several years. Copyright © 2017 Elsevier B.V. All rights reserved.

The presence of a negative sacral slope in patients with ankylosing spondylitis with severe thoracolumbar kyphosis.

PubMed

Qian, Bang-Ping; Jiang, Jun; Qiu, Yong; Wang, Bin; Yu, Yang; Zhu, Ze-Zhang

2014-11-19

Pelvic retroversion is one of the mechanisms for regulating sagittal balance in patients with a kyphotic deformity. This retroversion is limited by hip extension, which prevents the pelvis from becoming excessively retroverted, achieving a sacral slope of <0°. However, a negative sacral slope can be found in some patients with ankylosing spondylitis with thoracolumbar kyphosis. The purpose of this study was to analyze this finding. We performed a retrospective review of 106 consecutive Chinese Han patients with ankylosing spondylitis with thoracolumbar kyphosis treated at our center from October 2005 to October 2012. Forty-one patients in whom the upper third of the femur was clearly visualized on lateral radiographs were analyzed. Seventeen had a sacral slope of <0° (group A) and twenty-four had a sacral slope of ≥0° (group B). Eight sagittal parameters were measured and compared between the two groups. Correlations among sacral slope, the femoral obliquity angle, and the other sagittal parameters were analyzed. Mean global kyphosis, lumbar lordosis, pelvic tilt, the sagittal vertical axis, and the femoral obliquity angle were significantly larger in group A than in group B, whereas mean pelvic incidence and sacral slope were significantly smaller in group A (p < 0.05 for all). Global kyphosis, lumbar lordosis, pelvic tilt, and the sagittal vertical axis were significantly negatively associated with sacral slope but positively associated with the femoral obliquity angle, whereas pelvic incidence was significantly positively associated with sacral slope but negatively associated with the femoral obliquity angle (p < 0.05 for all). The femoral obliquity angle was significantly negatively associated with sacral slope (p < 0.05). Negative sacral slope does exist in Chinese Han patients with ankylosing spondylitis with thoracolumbar kyphosis. This appears to be caused by severe kyphosis, an initially small sacral slope, and pronounced tilting of the femoral shaft as a result of knee flexion, resulting in the pelvis becoming further retroverted. Copyright © 2014 by The Journal of Bone and Joint Surgery, Incorporated.

Assessment of undiscovered conventional oil and gas resources, onshore Claiborne Group, United Statespart of the northern Gulf of Mexico Basin

USGS Publications Warehouse

Hackley, P.C.; Ewing, T.E.

2010-01-01

The middle Eocene Claiborne Group was assessed for undiscovered conventional hydrocarbon resources using established U.S. Geological Survey assessment methodology. This work was conducted as part of a 2007 assessment of Paleogene-Neogene strata of the northern Gulf of Mexico Basin, including the United States onshore and state waters (Dubiel et al., 2007). The assessed area is within the Upper Jurassic-CretaceousTertiary composite total petroleum system, which was defined for the assessment. Source rocks for Claiborne oil accumulations are interpreted to be organic-rich, downdip, shaley facies of the Wilcox Group and the Sparta Sand of the Claiborne Group; gas accumulations may have originated from multiple sources, including the Jurassic Smackover Formation and the Haynesville and Bossier shales, the Cretaceous Eagle Ford and Pearsall (?) formations, and the Paleogene Wilcox Group and Sparta Sand. Hydrocarbon generation in the basin started prior to deposition of Claiborne sediments and is currently ongoing. Primary reservoir sandstones in the Claiborne Group include, from oldest to youngest, the Queen City Sand, Cook Mountain Formation, Sparta Sand, Yegua Formation, and the laterally equivalent Cockfield Formation. A geologic model, supported by spatial analysis of petroleum geology data, including discovered reservoir depths, thicknesses, temperatures, porosities, permeabilities, and pressures, was used to divide the Claiborne Group into seven assessment units (AUs) with three distinctive structural and depositional settings. The three structural and depositional settings are (1) stable shelf, (2) expanded fault zone, and (3) slope and basin floor; the seven AUs are (1) lower Claiborne stable-shelf gas and oil, (2) lower Claiborne expanded fault-zone gas, (3) lower Claiborne slope and basin-floor gas, (4) lower Claiborne Cane River, (5) upper Claiborne stable-shelf gas and oil, (6) upper Claiborne expanded fault-zone gas, and (7) upper Claiborne slope and basin-floor gas. Based on Monte Carlo simulation of justified input parameters, the total estimated mean undiscovered conventional hydrocarbon resources in the seven AUs combined are 52 million bbl of oil, 19.145 tcf of natural gas, and 1.205 billion bbl of natural gas liquids. This article describes the conceptual geologic model used to define the seven Claiborne AUs, the characteristics of each AU, and the justification behind the input parameters used to estimate undiscovered resources for each AU. The great bulk of undiscovered hydrocarbon resources are predicted to be nonassociated gas and natural gas liquids contained in deep (mostiy >12,000-ft [3658 m], present-day drilling depths), overpressured, structurally complex outer shelf or slope and basin-floor Claiborne reservoirs. The continuing development of these downdip objectives is expected to be the primary focus of exploration activity for the onshore middle Eocene Gulf Coast in the coming decades. ?? 2010 U.S. Geological Survey. All rights reserved.

Sleep duration partially accounts for race differences in diurnal cortisol dynamics.

PubMed

Peterson, Laurel M; Miller, Karissa G; Wong, Patricia M; Anderson, Barbara P; Kamarck, Thomas W; Matthews, Karen A; Kirschbaum, Clemens; Manuck, Stephen B

2017-05-01

Emerging research demonstrates race differences in diurnal cortisol slope, an indicator of hypothalamic-pituitary-adrenocortical (HPA)-axis functioning associated with morbidity and mortality, with African Americans showing flatter diurnal slopes than their White counterparts. Sleep characteristics are associated with both race and with HPA-axis functioning. The present report examines whether sleep duration may account for race differences in cortisol dynamics. Participants were 424 employed African American and White adults (mean age = 42.8 years, 84.2% White, 53.6% female) with no cardiovascular disease (Adult Health and Behavior Project-Phase 2 [AHAB-II] cohort, University of Pittsburgh). Cortisol slope was calculated using 4 salivary cortisol readings, averaged over each of 4 days. Demographic (age, sex), psychosocial (socioeconomic status [SES], affect, discrimination), and health behaviors (smoking, alcohol use, physical activity) variables were used as covariates, and sleep (self-report and accelerometry) was also assessed. African Americans had flatter slopes than Whites (F(1, 411) = 10.45, B = .02, p = .001) in models adjusting for demographic, psychosocial, and health behavior covariates. Shorter actigraphy-assessed total sleep time was a second significant predictor of flatter cortisol slopes (F(1, 411) = 25.27, B = -.0002, p < .0001). Total sleep time partially accounted for the relationship between race and diurnal slope [confidence interval = .05 (lower = .014, upper .04)]. African Americans have flatter diurnal cortisol slopes than their White counterparts, an effect that may be partially attributable to race differences in nightly sleep duration. Sleep parameters should be considered in further research on race and cortisol. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Beach Cusps: Spatial distribution and time evolution at Massaguaçú beach (SP), Brazil

NASA Astrophysics Data System (ADS)

dos Santos, H. H.; Siegle, E.; Sousa, P. H.

2013-05-01

Beach cusps are crescentic morphological structures observed on the foreshore of beaches characterized by steep seaward protruding extensions, called cusp horns, and gently sloped landward extensions, called cusp embayments. Their formation depends on the grain size, beach slope, tidal range and incoming waves. Cusps are best developed on gravel or shingle beaches, small tidal range with a large slope for incoming waves generate a well-developed swash excursion. These structures are quickly responding to wave climate and tidal range, changing the position of the rhythmic features on the beach face. Beach cusps are favored by normal incoming waves, while oblique waves tend to wash these features out. This study aims to analyze the spatial distribution and temporal evolution of rhythmic features such as beach cusps in Massaguaçú embayment (Caraguatatuba, northern coast of São Paulo, Brazil). This embayment has an extension of 7.5 km with reflective beaches cusped mainly in its more exposed central portion. The data set for this study consists of a series of video images (Argus system), covering a stretch of the beach. Visible beach cusps were digitalized from these rectified images. Results obtained from the images were related to the wave climate, water level and the storm surges. Results show that the cusps on the upper portion of the foreshore were more regular and present than the cusps on the lower portion of the foreshore due to the tidal modulation of wave action. The cusp spacing on the upper portion of the foreshore is of about 38 m and the lower portion of the foreshore is of about 28 m and their presence was correlated with the wave direction and water elevation. As expected, waves approaching with shore-normal angles (southeast direction) were favorable to the formation of beach cusps while the waves from the southwest, south, east and northeast generated a longshore current that reduced or destroyed any rhythmic feature. Other important forcing was the influence of the water level. Waves acting at higher water levels are able to produce the less dynamic upper layer of cusps. During 31 consecutive days from 8 July 2011 to 8 August of the same year these features show four periods with the presence of cusps on the upper and lower portion of the foreshore with three periods with cups only on the upper portion of the foreshore. The analyzed dataset shows the highly dynamic behavior of cusps, with rapid generation and destruction, related directly to its forcing hydrodynamic conditions.

Age and microfacies of oceanic Upper Triassic radiolarite components from the Middle Jurassic ophiolitic mélange in the Zlatibor Mountains (Inner Dinarides, Serbia) and their provenance

NASA Astrophysics Data System (ADS)

Gawlick, Hans-Jürgen; Djerić, Nevenka; Missoni, Sigrid; Bragin, Nikita Yu.; Lein, Richard; Sudar, Milan; Jovanović, Divna

2017-08-01

Oceanic radiolarite components from the Middle Jurassic ophiolitic mélange between Trnava and Rožanstvo in the Zlatibor Mountains (Dinaridic Ophiolite Belt) west of the Drina-Ivanjica unit yield Late Triassic radiolarian ages. The microfacies characteristics of the radiolarites show pure ribbon radiolarites without crinoids or thin-shelled bivalves. Beside their age and the preservation of the radiolarians this points to a deposition of the radiolarites on top of the oceanic crust of the Neo-Tethys, which started to open in the Late Anisian. South of the study area the ophiolitic mélange (Gostilje-Ljubiš-Visoka-Radoševo mélange) contains a mixture of blocks of 1) oceanic crust, 2) Middle and Upper Triassic ribbon radiolarites, and 3) open marine limestones from the continental slope. On the basis of this composition we can conclude that the Upper Triassic radiolarite clasts derive either from 1) the younger parts of the sedimentary succession above the oceanic crust near the continental slope or, more convincingly 2) the sedimentary cover of ophiolites in a higher nappe position, because Upper Triassic ribbon radiolarites are only expected in more distal oceanic areas. The ophiolitic mélange in the study area overlies different carbonate blocks of an underlying carbonate-clastic mélange (Sirogojno mélange). We date and describe three localities with different Upper Triassic radiolarite clasts in a mélange, which occurs A) on top of Upper Triassic fore-reef to reefal limestones (Dachstein reef), B) between an Upper Triassic reefal limestone block and a Lower Carnian reef limestone (Wetterstein reef), and C) in fissures of an Upper Triassic lagoonal to back-reef limestone (Dachstein lagoon). The sedimentary features point to a sedimentary and not to a tectonic emplacement of the ophiolitic mélange (= sedimentary mélange) filling the rough topography of the topmost carbonate-clastic mélange below. The block spectrum of the underlying and slightly older carbonate-clastic mélange points to a deposition of the sedimentary ophiolitic mélange east of or on top of the Drina-Ivanjica unit.

The subsurface geology of the Florida-Hatteras shelf, slope, and inner Blake Plateau

USGS Publications Warehouse

Paull, Charles K.; Dillon, William P.

1979-01-01

The structure and stratigraphy of the Florida-Hatteras Slope and inner Blake Plateau was studied by means of 4,780 km of single-channel air gun seismic reflection profiles. Control for the seismic stratigraphy is provided by correlating reflecting units and paleontologically dated stratigraphic units identified in offshore wells and dredge hauls. Many Tertiary unconformities exist, and major regional unconformities at the end of the Oligocene and in the late Paleocene are mapped. Reflecting surfaces believed to represent the tops of the Cretaceous, Paleocene, and Oligocene extend throughout the region. Upper Cretaceous (pre-Maastrichtian) rocks on the southeastern side of the Carolina Platform form a large seaward-facing progradational wedge. The Upper Cretaceous rocks in the Southeast Georgia Embayment, are seismically transparent and on the inner Blake Plateau are cut by numerous small faults, perhaps due to compaction. Within the survey area relatively flat-lying Maastrichtian and Paleocene strata show no evidence that a feature similar to the present Florida-Hatteras Slope existed at the beginning of the Tertiary. Late Paleocene erosion, related to the initiation of the Gulf Stream flow, probably developed this regional unconformity. Eocene and Oligocene sediments landward of the present Gulf Stream form a thick sequence of seaward-dipping progradational beds. A seaward progradational wedge of Miocene to Holocene age covers a regionally traceable unconformity, which separates the Oligocene from the Miocene sediments. Under and seaward of the present Gulf Stream, the Eocene and younger sediment supply was much smaller and the buildup is comparatively insignificant. The difference in accumulation rates in the Eocene and younger sediments, landward and seaward of the Gulf Stream, is responsible for the Florida-Hatteras Slope. Tertiary isopach maps suggest that there is a well developed triangular depocenter under the shelf. The edges of the depocenter correspond with magnetic anomalies and it is suggested that the depocenter is related to differential subsidence during the Tertiary across older crustal structures. The Eocene and Oligocene units contain the aquifer onshore, and the aquifer probably remains in these units offshore. With this assumption the potential aquifer has been identified and traced under the shelf and slope.

Inorganic geochemistry of surface sediments of the Ebro shelf and slope, northwestern Mediterranean

USGS Publications Warehouse

Gardner, J.V.; Dean, W.E.; Alonso, B.

1990-01-01

Distributions of major, minor, and trace elements in surface sediment of the continental shelf and upper slope of the northeastern Spanish continental margin reflect the influences of discharge from the Ebro River and changes in eustatic sea levels. Multivariate factor analysis of sediment geochemistry was used to identify five groupings of samples (factors) on the shelf and slope. The first factor is an aluminosilicate factor that represents detrital clastic material. The second factor is a highly variable amount of excess SiO2 and probably represents a quartz residuum originating from winnowing of relict detrital sediments. A carbonate factor (Factor 3) has no positive correlation with other geochemical parameters but is associated with the sand-size fraction. The carbonate in these sediments consists of a mixture of biogenic calcite and angular to subangular detrital grains. Organic carbon is associated with the aluminosilicate factor (Factor 1) but also factors out by itself (Factor 4); this suggests that there may be two sources of organic matter, terrestrial and marine. The fifth factor comprises upper slope sediments that contain high concentrations of manganese. The most likely explanation for these high manganese concentrations is precipitation of Mn oxyhydroxides at the interface between Mn-rich, oxygen-deficient, intermediate waters and oxygenated surface waters. During eustatic low sea levels of the glacial Pleistocene, the Ebro Delta built across the outer continental shelf and deposited sediment with fairly high contents of organic carbon and continental components. The period of marine transgression from eustatic low (glacial) to eustatic high (interglacial) sea levels was characterized by erosion of the outer shelf delta and surficial shelf sediments and the transport of sediment across the slope within numerous canyons. Once eustatic high sea level was reached, delta progradation resumed on the inner shelf. Today, coarse-grained sediment (silt and sand) is transported to the continental shelf by Ebro River and is distributed along the inner shelf by currents generated by dominant northeasterly winds. Clay-size material is deposited on the mid- and outer-shelf. However, erosion and delta progradation during the last glacial period, and fine-grained Holocene sedimentation, have probably produced a distribution of sediment on a diachronous surface. ?? 1990.

Marine fish community structure and habitat associations on the Canadian Beaufort shelf and slope

NASA Astrophysics Data System (ADS)

Majewski, Andrew R.; Atchison, Sheila; MacPhee, Shannon; Eert, Jane; Niemi, Andrea; Michel, Christine; Reist, James D.

2017-03-01

Marine fishes in the Canadian Beaufort Sea have complex interactions with habitats and prey, and occupy a pivotal position in the food web by transferring energy between lower- and upper-trophic levels, and also within and among habitats (e.g., benthic-pelagic coupling). The distributions, habitat associations, and community structure of most Beaufort Sea marine fishes, however, are unknown thus precluding effective regulatory management of emerging offshore industries in the region (e.g., hydrocarbon development, shipping, and fisheries). Between 2012 and 2014, Fisheries and Oceans Canada conducted the first baseline survey of offshore marine fishes, their habitats, and ecological relationships in the Canadian Beaufort Sea. Benthic trawling was conducted at 45 stations spanning 18-1001 m depths across shelf and slope habitats. Physical oceanographic variables (depth, salinity, temperature, oxygen), biological variables (benthic chlorophyll and integrated water-column chlorophyll) and sediment composition (grain size) were assessed as potential explanatory variables for fish community structure using a non-parametric statistical approach. Selected stations were re-sampled in 2013 and 2014 for a preliminary assessment of inter-annual variability in the fish community. Four distinct fish assemblages were delineated on the Canadian Beaufort Shelf and slope: 1) Nearshore-shelf: <50 m depth, 2) Offshore-shelf: >50 and ≤200 m depths, 3) Upper-slope: ≥200 and ≤500 m depths, and 4) Lower-slope: ≥500 m depths. Depth was the environmental variable that best explained fish community structure, and each species assemblage was spatially associated with distinct aspects of the vertical water mass profile. Significant differences in the fish community from east to west were not detected, and the species composition of the assemblages on the Canadian Beaufort Shelf have not changed substantially over the past decade. This community analysis provides a framework for testing hypotheses regarding the trophic dynamics and ecosystem roles of Beaufort Sea marine fishes, including biological linkages (i.e., fish movements and trophic interactions) among offshore habitats. Understanding regional-scale habitat associations will also provide context to identify potentially unique and/or sensitive habitats and fish community characteristics, thus aiding identification of ecologically and biologically significant areas, and to inform conservation efforts.

Understanding Variability in Beach Slope to Improve Forecasts of Storm-induced Water Levels

NASA Astrophysics Data System (ADS)

Doran, K. S.; Stockdon, H. F.; Long, J.

2014-12-01

The National Assessment of Hurricane-Induced Coastal Erosion Hazards combines measurements of beach morphology with storm hydrodynamics to produce forecasts of coastal change during storms for the Gulf of Mexico and Atlantic coastlines of the United States. Wave-induced water levels are estimated using modeled offshore wave height and period and measured beach slope (from dune toe to shoreline) through the empirical parameterization of Stockdon et al. (2006). Spatial and temporal variability in beach slope leads to corresponding variability in predicted wave setup and swash. Seasonal and storm-induced changes in beach slope can lead to differences on the order of a meter in wave runup elevation, making accurate specification of this parameter essential to skillful forecasts of coastal change. Spatial variation in beach slope is accounted for through alongshore averaging, but temporal variability in beach slope is not included in the final computation of the likelihood of coastal change. Additionally, input morphology may be years old and potentially very different than the conditions present during forecast storm. In order to improve our forecasts of hurricane-induced coastal erosion hazards, the temporal variability of beach slope must be included in the final uncertainty of modeled wave-induced water levels. Frequently collected field measurements of lidar-based beach morphology are examined for study sites in Duck, North Carolina, Treasure Island, Florida, Assateague Island, Virginia, and Dauphin Island, Alabama, with some records extending over a period of 15 years. Understanding the variability of slopes at these sites will help provide estimates of associated water level uncertainty which can then be applied to other areas where lidar observations are infrequent, and improve the overall skill of future forecasts of storm-induced coastal change. Stockdon, H. F., Holman, R. A., Howd, P. A., and Sallenger Jr, A. H. (2006). Empirical parameterization of setup,swash, and runup. Coastal engineering, 53(7), 573-588.

The Three-Dimensional (3D) Numerical Stability Analysis of Hyttemalmen Open-Pit

NASA Astrophysics Data System (ADS)

Cała, Marek; Kowalski, Michał; Stopkowicz, Agnieszka

2014-10-01

The purpose of this paper was to perform the 3D numerical calculations allowing slope stability analysis of Hyttemalmen open pit (location Kirkenes, Finnmark Province, Norway). After a ramp rock slide, which took place in December 2010, as well as some other small-scale rock slope stability problems, it proved necessary to perform a serious stability analyses. The Hyttemalmen open pit was designed with a depth up to 100 m, a bench height of 24 m and a ramp width of 10 m. The rock formation in the iron mining district of Kirkenes is called the Bjornevaten Group. This is the most structurally complicated area connected with tectonic process such as folding, faults and metamorphosis. The Bjornevaten Group is a volcano-sedimentary sequence. Rock slope stability depends on the mechanical properties of the rock, hydro-geological conditions, slope topography, joint set systems and seismic activity. However, rock slope stability is mainly connected with joint sets. Joints, or general discontinuities, are regarded as weak planes within rock which have strength reducing consequences with regard to rock strength. Discontinuities within the rock mass lead to very low tensile strength. Several simulations were performed utilising the RocLab (2007) software to estimate the gneiss cohesion for slopes of different height. The RocLab code is dedicated to estimate rock mass strength using the Hoek-Brown failure criterion. Utilising both the GSI index and the Hoek-Brown strength criterion the equivalent Mohr-Coulomb parameters (cohesion and angle of internal friction) can be calculated. The results of 3D numerical calculations (with FLA3D code) show that it is necessary to redesign the slope-bench system in the Hyttemalmen open pit. Changing slope inclination for lower stages is recommended. The minimum factor of safety should be equal 1.3. At the final planned stage of excavation, the factor of safety drops to 1.06 with failure surface ranging through all of the slopes. In the case of a slope angle 70° for lower stages, FS = 1.26, which is not enough to provide slope stability. Another series of calculations were therefore performed taking water table lowering into consideration, which increases the global safety factor. It was finally evaluated, that for a water table level of 72 m the factor of safety equals 1.3, which is enough to assure global open-pit stability.

Performance of San Fernando dams during 1994 Northridge earthquake

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bardet, J.P.; Davis, C.A.

1996-07-01

The 1994 Northridge and 1971 San Fernando Earthquakes subjected the Lower and Upper San Fernando Dams of the Van Norman Complex in the San Fernando Valley, Calif., to strong near-source ground motions. In 1994, these earth dams, which were out of service and retained only a few meters of water, extensively cracked and settled due to the liquefaction of their hydraulic fill. The Lower San Fernando Dam moved over 15 cm upstream as the hydraulic fill liquefied beneath its upstream slope. The Upper San Fernando Dam moved even more and deformed in a complicated three-dimensional pattern. The responses of themore » Lower and Upper San Fernando Dams during the 1994 Northridge Earthquake, although less significant than in 1971, provide the geotechnical engineering community with two useful case histories.« less

Leg 67: the Deep Sea Drilling Project Mid-America Trench transect off Guatemala.

USGS Publications Warehouse

von Huene, Roland E.

1980-01-01

Drilling on the Cocos plate recovered a basal chalk sequence deposited during early and mid-Miocene time, a short interval of abyssal red clay, and an upper sequence of late Miocene and younger sediment deposited within an area influenced by a terrigenous source. In the trench, a mud and sand fill less than 400,000 yr old overlies the oceanic sequence. The entire section shows no evidence of compressive deformation. In contrast, the section cored on the trench's landward slope 3 km from the trench axis is affected by tectonism. The section contains a Cretaceous to Pliocene claystone sequence capped by Pliocene to Quaternary hemipelagic slope deposits.- from Authors

Lunar Roving Vehicle parked in lunar depression on slope of Stone Mountain

NASA Image and Video Library

1972-04-22

AS16-107-17473 (22 April 1972) --- The Lunar Roving Vehicle (LRV) appears to be parked in a deep lunar depression, on the slope of Stone Mountain. This photograph of the lunar scene at Station No. 4 was taken during the second Apollo 16 extravehicular activity (EVA) at the Descartes landing site. A sample collection bag is in the right foreground. Note field of small boulders at upper right. While astronauts John W. Young, commander, and Charles M. Duke Jr., lunar module pilot, descended in the Lunar Module (LM) "Orion" to explore the moon, astronaut Thomas K. Mattingly II, command module pilot, remained with the Command and Service Modules (CSM) in lunar orbit.

Noise measurements obtained during engineering evaluation of two-segment approaches in a 727-200 aircraft

NASA Technical Reports Server (NTRS)

Tanner, C. S.; Glass, R. E.

1974-01-01

A series of noise measurements were made during engineering evaluation tests of two-segment approaches in a 727-200 aircraft equipped with acoustically treated nacelles. A two-segment approach having a 6-degree upper glide slope angle intercepting the Instrument Landing System (ILS) 2.9-degree glide slope at an altitude of 690 feet gave a 5-EPNdB decrease in measured noise at distances greater than 3 nautical miles from the runway threshold when compared with a normal ILS approach. Several of the noise measurements were taken under adverse weather conditions which were outside the specified limits of FAR Part 36. This may introduce uncertainties into the data from several approaches.

Slope Estimation in Noisy Piecewise Linear Functions✩

PubMed Central

Ingle, Atul; Bucklew, James; Sethares, William; Varghese, Tomy

2014-01-01

This paper discusses the development of a slope estimation algorithm called MAPSlope for piecewise linear data that is corrupted by Gaussian noise. The number and locations of slope change points (also known as breakpoints) are assumed to be unknown a priori though it is assumed that the possible range of slope values lies within known bounds. A stochastic hidden Markov model that is general enough to encompass real world sources of piecewise linear data is used to model the transitions between slope values and the problem of slope estimation is addressed using a Bayesian maximum a posteriori approach. The set of possible slope values is discretized, enabling the design of a dynamic programming algorithm for posterior density maximization. Numerical simulations are used to justify choice of a reasonable number of quantization levels and also to analyze mean squared error performance of the proposed algorithm. An alternating maximization algorithm is proposed for estimation of unknown model parameters and a convergence result for the method is provided. Finally, results using data from political science, finance and medical imaging applications are presented to demonstrate the practical utility of this procedure. PMID:25419020

Slope Estimation in Noisy Piecewise Linear Functions.

PubMed

Ingle, Atul; Bucklew, James; Sethares, William; Varghese, Tomy

2015-03-01

This paper discusses the development of a slope estimation algorithm called MAPSlope for piecewise linear data that is corrupted by Gaussian noise. The number and locations of slope change points (also known as breakpoints) are assumed to be unknown a priori though it is assumed that the possible range of slope values lies within known bounds. A stochastic hidden Markov model that is general enough to encompass real world sources of piecewise linear data is used to model the transitions between slope values and the problem of slope estimation is addressed using a Bayesian maximum a posteriori approach. The set of possible slope values is discretized, enabling the design of a dynamic programming algorithm for posterior density maximization. Numerical simulations are used to justify choice of a reasonable number of quantization levels and also to analyze mean squared error performance of the proposed algorithm. An alternating maximization algorithm is proposed for estimation of unknown model parameters and a convergence result for the method is provided. Finally, results using data from political science, finance and medical imaging applications are presented to demonstrate the practical utility of this procedure.

Characterization of oil and gas reservoir heterogeneity; Final report, November 1, 1989--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, G.D.

1993-09-01

The Alaskan North Slope comprises one of the Nation`s and the world`s most prolific oil province. Original oil in place (OOIP) is estimated at nearly 70 BBL (Kamath and Sharma, 1986). Generalized reservoir descriptions have been completed by the University of Alaska`s Petroleum Development Laboratory over North Slope`s major fields. These fields include West Sak (20 BBL OOIP), Ugnu (15 BBL OOIP), Prudhoe Bay (23 BBL OOIP), Kuparuk (5.5 BBL OOIP), Milne Point (3 BBL OOIP), and Endicott (1 BBL OOIP). Reservoir description has included the acquisition of open hole log data from the Alaska Oil and Gas Conservation Commissionmore » (AOGCC), computerized well log analysis using state-of-the-art computers, and integration of geologic and logging data. The studies pertaining to fluid characterization described in this report include: experimental study of asphaltene precipitation for enriched gases, CO{sup 2} and West Sak crude system, modeling of asphaltene equilibria including homogeneous as well as polydispersed thermodynamic models, effect of asphaltene deposition on rock-fluid properties, fluid properties of some Alaskan north slope reservoirs. Finally, the last chapter summarizes the reservoir heterogeneity classification system for TORIS and TORIS database.« less

Triggering factor evolution and dynamic process simulation of the Formosa Highway dip-slope failure, northern Taiwan

NASA Astrophysics Data System (ADS)

Huang, Mei-Jen; Chiang, Yi-Lin; Chang, Ho-Shyang; Chang, Kuo-Jen

2013-04-01

Taiwan, due to the high seismicity and high annual rainfall, numerous landslides triggered every year and severe impacts affect the island. Accordingly, if the new-built construction does not take into account this threaten, tremendous disasters will occur. On April 25th 2010, Formosa Freeway dip-slope failure caused four deaths, resulted from artificial slope cutting and rock-bot supporting system weakening. This research integrates high resolution Digital Terrain Model (DTM) and numerical simulation to evaluate the triggering mechanism and dynamic process of the landslide. First of all, to access the landslide geometry, the morphology of the event before and after landslide is constructed from high resolution DTM by means of aerial photos. The slid and the deposit volumes of the landslide are thus estimated accordingly. Only part of the surface of separation between slide block and slide slope is exposed. Based on the exposed planar strata/sliding surface, situated on the upper part of the slope, by means of extrapolating part of the plane to mimic the entire slide surface. From DTMs, the slide block is approximately 0.15 million cubic meters. The extrapolated planar surface serves as sliding surface for the numerical models. For numerical model preparation, the particle clusters produced by isotropic stress and the porosity are take into account. To ensure the production range should cover the entire slid mass from the source area, the particle clusters represent the slid block is been rotated, scaled and translated to the source area. Then, part of the particles are been eliminated if it is situated outside the upper and lower surface from the DTM before and after landslide. According to the geological map, the model of the particles to mimic the slide block can be divided into two parts: 1) the underneath interbedded sandstone and shale which may soften by water 2) the supposed upper layer composed of sandstone. Furthermore, set up a layer of particles to simulate ground anchor. The advantages of DTM collocate PFC3d are that real terrain can be represented on the model, and can be simulated the complete landslide process dynamically. Comparing with continuum mechanic analysis that only provides state of instability, but by using discrete element method it can provide the dynamical process of sliding include trajectory, velocity change, sliding distance and also accumulation patterns after landslide and know the affected areas from the disaster event. Results shows: 1) the peak and the residual frictional angle of the sliding surface should be small than 14 and 4 degree, respectively, in the condition of 30% effective resistance of rock-bolt remains. 2)The maximum sliding speed could be as high as 15.34 m/s, caused thus hazard event.

A new vision of carbonate slopes: the Little Bahama Bank

NASA Astrophysics Data System (ADS)

Mulder, Thierry; Gillet, Hervé; Hanquiez, Vincent; Reijmer, John J.; Tournadour, Elsa; Chabaud, Ludivine; Principaud, Mélanie; Schnyder, Jara; Borgomano, Jean

2015-04-01

Recent data collected in November 2014 (RV Walton Smith) on the upper slope of the Little Bahama Bank (LBB) between 30 and 400 m water depth allowed to characterize the uppermost slope (Rankey et al., 2012) over a surface of 170 km2. The new data set includes multibeam bathymetry and acoustic imagery, 3.5 kHz very-high resolution (VHR) seismic reflection lines, 21 gravity cores and 11 Van Veen grabs. The upper slope of the LBB does not show a steep submarine cliff as known from western Great Bahama Bank. The carbonate bank progressively deepens towards the basin through a slighty inclined plateau. The slope value is < 6° down to a water depth of about 70 m. The plateau is incised by decameter-wide gullies that covered with indurated sediment. Some of the gullies like Roberts Cuts show a larger size and may play an important role in sediment transfer from the shallow-water carbonate bank down to the canyon heads at 400-500 m water depth (Mulder et al., 2012). In the gully area, the actual reef rests on paleo-reefs that outcrop at a water depth of about 40 m. These paleo-reef structures could represent reefs that established themselves during past periods of sea-level stagnation. Below this water depth, the slope steepens up to 30° to form the marginal escarpment (Rankey et al., 2012), which is succeeded by the open margin realm (Rankey et al., 2012). The slope inclination value decreases at about 180-200 m water depth. Between 20 and 200 m of water depth, the VHR seismic shows no seafloor sub-bottom reflector. Between 180 and 320 m water depth, the seafloor smoothens. The VHR seismic shows an onlapping sediment wedge, which starts in this water depth and shows a blind or very crudely stratified echo facies. The sediment thickness of this Holocene unit may exceed 20 m. It fills small depressions in the substratum and thickens in front of gullies that cut the carbonate platform edge. Sediment samples show the abundancy of carbonate mud on the present Bahamian seafloor. In gullies, coarser sediment can be found. In some case, soft sediments are absent suggesting by-passing. At water depth between 40 and 100 m, the present-day seafloor is covered with bioclastic sediments. The main carbonate producer seems to be the alga genus Halimeda. Sediments collected in the deeper part of the basin (water depth = 1080 m) on the distal lobe consist of massive fine to medium well-sorted aragonitic sand. This suggests that carbonate slope systems are able to sort sediment despite the relative short slope distance. Sorting could either be due to flow spilling above the terraces identified in the canyon heads (Mulder et al., 2012) or could result from bottom currents. In this area, flow velocity profiles in the water column show the presence of two superposed water masses with a pycnocline at about 600-700 m water depth. Mulder, T., Ducassou, E., Gillet, H., Hanquiez, V., Tournadour, E., Combes, J., Eberli, G.P, Kindler, P., Gonthier, E., Conesa, G., Robin, C., Sianipar, R., Reijmer, J.J.G., and François A. Canyon morphology on a modern carbonate slope of the Bahamas: Evidence of regional tectonic tilting. Geology, 40(9), 771-774. Rankey, E.C, and Doolittle, D.F. (2012). Geomorphology of carbonate platform-marginal uppermost slopes: Insights from a Holocene analogue, Little Bahama Bank, Bahamas. Sedimentology, 59, 2146-2171.

A Primer on the Statistical Modelling of Learning Curves in Health Professions Education

ERIC Educational Resources Information Center

Pusic, Martin V.; Boutis, Kathy; Pecaric, Martin R.; Savenkov, Oleksander; Beckstead, Jason W.; Jaber, Mohamad Y.

2017-01-01

Learning curves are a useful way of representing the rate of learning over time. Features include an index of baseline performance (y-intercept), the efficiency of learning over time (slope parameter) and the maximal theoretical performance achievable (upper asymptote). Each of these parameters can be statistically modelled on an individual and…

A Comparison of Vegetation Within and Outside Riparian Areas Bordering Ephemeral Streams in the Ouachita Mountains

Treesearch

David K. Radabaugh; Hal O. Liechty; James M. Guldin

2004-01-01

Abstract - Ephemeral streams frequently occur in shortleaf pine (Pinus echinata Mill.) hardwood stands that grow on the upper and mid-slopes of the Ouachita Mountains in Arkansas. Stream management zones are established around these ephemeral streams in the Ouachita National Forest to minimize impacts of adjacent forest management...

Sedimentation across the central California oxygen minimum zone: an alternative coastal upwelling sequence.

USGS Publications Warehouse

Vercoutere, T.L.; Mullins, H.T.; McDougall, K.; Thompson, J.B.

1987-01-01

Distribution, abundance, and diversity of terrigenous, authigenous, and biogenous material provide evidence of the effect of bottom currents and oxygen minimum zone (OMZ) on continental slope sedimentation offshore central California. Three major OMZ facies are identified, along the upper and lower edges of OMZ and one at its core.-from Authors

Monitoring of Streambank Stabilization and River Restoration Structures on Ice-Affected Rivers in Northern Vermont

DTIC Science & Technology

2009-08-01

Site Characteristics River Site Drainage Area ( mi2 ) Valley Bottom Slope Bank- full Width (ft) Bank- full Depth (ft) Bankfull...relatively unaltered by human activities. Drainage areas range from 990 ERDC/CRREL TR-09-14 17 mi2 on the lower Winooski to 44 mi2 on the upper Trout

Upland forest vegetation of the Ozark Mountains in Northwestern Arkansas

Treesearch

Steven L. Stephenson; Harold S. Adams; Cynthia D. Huebner

2007-01-01

Quantitative data on structure and composition of all strata of vegetation were collected from 20 study sites in the Boston Mountains Subsection of the Ozark Mountains of northwestern Arkansas in June 2004. All study sites were located at upper slope or ridgetop positions and occurred at elevations > 457 m. Oaks (Quercus spp.) were dominants in...

Late Wisconsin and Early Holocene runoff through the upper Ohio River basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kite, J.S.

A tentative absolute chronology is emerging from radiocarbon dates on glacial, alluvial and colluvial sediments in the upper Ohio River basin. Radiocarbon dates for Gallipolis Lock and Dam indicate the river eroded down to its present bedrock floor before 22,400 yr B.P. Data from several sites indicate aggradation began soon after 22,400 yr B.P., coincident with, or just before, a glacier advance into the upper Ohio basin. Sand and gravel aggraded in glaciated tributaries and the main valley, whereas silt, fine sand, and clay accumulated in unglaciated tributaries. Slope instability and colluvial deposition were extensive at this time. Aggradation continuedmore » until 25 to 40 m of sediments filled the Ohio River Valley. The paucity of radiocarbon dates prohibits precise determination of when peak aggradation occurred and how that peak related to glacial and climatic events. Although the Laurentide Ice Sheet retreated out of the basin by about 14,000 yr B.P., the river remained braided until at least 13,000 yr B.P., possibly because of slope instability in a cold late Wisconsin climate or the time required for the river to adjust to reduced outwash sediment supply. Coarse late-glacial channel deposits may reflect increased flood discharges after 13,000 B.P. and onset of the transition from a braided system to a meandering channel. However, the upper Ohio River seems not to have taken on its modern morphology until the early Holocene. Most dated overbank deposits on tributaries are younger than 10,000 yr B.P.; most on the Ohio River are younger than 8,500 yr B.P.« less

Temperature Dependence of the Upper Critical Field in Disordered Hubbard Model with Attraction

NASA Astrophysics Data System (ADS)

Kuchinskii, E. Z.; Kuleeva, N. A.; Sadovskii, M. V.

2017-12-01

We study disorder effects upon the temperature behavior of the upper critical magnetic field in an attractive Hubbard model within the generalized DMFT+Σ approach. We consider the wide range of attraction potentials U—from the weak coupling limit, where superconductivity is described by BCS model, up to the strong coupling limit, where superconducting transition is related to Bose-Einstein condensation (BEC) of compact Cooper pairs, formed at temperatures significantly higher than superconducting transition temperature, as well as the wide range of disorder—from weak to strong, when the system is in the vicinity of Anderson transition. The growth of coupling strength leads to the rapid growth of H c2( T), especially at low temperatures. In BEC limit and in the region of BCS-BEC crossover H c2( T), dependence becomes practically linear. Disordering also leads to the general growth of H c2( T). In BCS limit of weak coupling increasing disorder lead both to the growth of the slope of the upper critical field in the vicinity of the transition point and to the increase of H c2( T) in the low temperature region. In the limit of strong disorder in the vicinity of the Anderson transition localization corrections lead to the additional growth of H c2( T) at low temperatures, so that the H c2( T) dependence becomes concave. In BCS-BEC crossover region and in BEC limit disorder only slightly influences the slope of the upper critical field close to T c . However, in the low temperature region H c2 ( T may significantly grow with disorder in the vicinity of the Anderson transition, where localization corrections notably increase H c2 ( T = 0) also making H c2( T) dependence concave.

Slope Stability Analysis of Waste Dump in Sandstone Open Pit Osielec

NASA Astrophysics Data System (ADS)

Adamczyk, Justyna; Cała, Marek; Flisiak, Jerzy; Kolano, Malwina; Kowalski, Michał

2013-03-01

This paper presents the slope stability analysis for the current as well as projected (final) geometry of waste dump Sandstone Open Pit "Osielec". For the stability analysis six sections were selected. Then, the final geometry of the waste dump was designed and the stability analysis was conducted. On the basis of the analysis results the opportunities to improve the stability of the object were identified. The next issue addressed in the paper was to determine the proportion of the mixture containing mining and processing wastes, for which the waste dump remains stable. Stability calculations were carried out using Janbu method, which belongs to the limit equilibrium methods.

Assessment of spatial distribution of soil loss over the upper basin of Miyun reservoir in China based on RS and GIS techniques.

PubMed

Chen, Tao; Niu, Rui-qing; Wang, Yi; Li, Ping-xiang; Zhang, Liang-pei; Du, Bo

2011-08-01

Soil conservation planning often requires estimates of the spatial distribution of soil erosion at a catchment or regional scale. This paper applied the Revised Universal Soil Loss Equation (RUSLE) to investigate the spatial distribution of annual soil loss over the upper basin of Miyun reservoir in China. Among the soil erosion factors, which are rainfall erosivity (R), soil erodibility (K), slope length (L), slope steepness (S), vegetation cover (C), and support practice factor (P), the vegetative cover or C factor, which represents the effects of vegetation canopy and ground covers in reducing soil loss, has been one of the most difficult to estimate over broad geographic areas. In this paper, the C factor was estimated based on back propagation neural network and the results were compared with the values measured in the field. The correlation coefficient (r) obtained was 0.929. Then the C factor and the other factors were used as the input to RUSLE model. By integrating the six factor maps in geographical information system (GIS) through pixel-based computing, the spatial distribution of soil loss over the upper basin of Miyun reservoir was obtained. The results showed that the annual average soil loss for the upper basin of Miyun reservoir was 9.86 t ha(-1) ya(-1) in 2005, and the area of 46.61 km(2) (0.3%) experiences extremely severe erosion risk, which needs suitable conservation measures to be adopted on a priority basis. The spatial distribution of erosion risk classes was 66.9% very low, 21.89% low, 6.18% moderate, 2.89% severe, and 1.84% very severe. Thus, by using RUSLE in a GIS environment, the spatial distribution of water erosion can be obtained and the regions which susceptible to water erosion and need immediate soil conservation planning and application over the upper watershed of Miyun reservoir in China can be identified.

Complex Burial and Exhumation of South Polar Cap Pitted Terrain

NASA Technical Reports Server (NTRS)

2000-01-01

This image is illuminated by sunlight from the upper left. The two prominent bright stripes at the left/center of the image are covered with bright frost and thus create the illusion that they are sunlit from the lower left.

The large pits, troughs, and 'swiss cheese' of the south polar residual cap appear to have been formed in the upper 4 or 5 layers of the polar material. Each layer is approximately 2 meters (6.6 feet) thick. Some Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) images of this terrain show examples in which older pitted and eroded layers have been previously buried and are now being exhumed. The example shown here includes two narrow, diagonal slopes that trend from upper left toward lower right at the left/center portion of the frame. Along the bottoms of these slopes are revealed a layer that underlies them in which there are many more pits and troughs than in the upper layer. It is likely in this case that the lower layer formed its pits and troughs before it was covered by the upper layer. This observation suggests that the troughs, pits, and 'swiss cheese' features of the south polar cap are very old and form over long time scales.

The picture is located near 84.6oS, 45.1oW, and covers an area 3 km by 5 km (1.9 x 3.1 mi) at a resolution of about 3.8 meters (12 ft) per pixel. The image was taken during southern spring on August 29, 1999.

Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

The Effect of Uphill and Downhill Slopes on Weight Transfer, Alignment and Shot Outcome in Golf.

PubMed

Blenkinsop, Glen M; Liang, Ying; Gallimore, Nicholas J; Hiley, Michael J

2018-04-13

The aim of the study was to examine changes in weight transfer, alignment and shot outcome during golf shots from flat, uphill, and downhill slopes. Twelve elite male golfers hit 30 shots with a six-iron from a computer assisted rehabilitation environment (CAREN) used to create 5° slopes while collecting 3D kinematics and kinetics of the swing. A launch monitor measured performance outcomes. A shift in the centre of pressure was found throughout the swing when performed on a slope, with the mean position moving approximately 9% closer to the lower foot. The golfers attempted to remain perpendicular to the slope, resulting in the weight transfer towards the lower foot. The golfers adopted a wider stance in the sloped conditions and moved the ball towards the higher foot at address. Ball speed was not significantly affected by the slope, but launch angle and ball spin were. As predicted by the coaching literature, golfers were more likely to hit shots to the left from an uphill slope and to the right for a downhill slope. No consistent compensatory adjustments in alignment at address or azimuth were found, with the change in final shot dispersion due to the lateral spin of the ball.

An intraslab earthquake (M7.1) along a buried hydrated fault in the Pacific plate, triggered by the 2011 M9 Tohoku earthquake

NASA Astrophysics Data System (ADS)

Nakajima, J.; Hasegawa, A.; Kita, S.

2011-12-01

A M9.0 megathrust earthquake, the 2011 off the Pacific Coast of Tohoku Earthquake, occurred on 11 March 2011 on the plate boundary east off northeastern (NE) Japan. After this great earthquake, seismicity has been activated in the Pacific plate as well as along its upper surface, and a large earthquake (M7.1) occurred on April 7 in the Pacific slab at a depth of 66 km, located near the down-dip limit of the large interplate slip of the M9 event. Here we perform travel-time tomography to reveal heterogeneous seismic velocity structures around the focal area of the 2011 M7.1 intraslab event, and discuss the occurrence of the 2011 M7.1 event in terms of dehydration embrittlement hypothesis. We applied the double-difference tomography method (Zhang and Thurber, 2003) to large number of arrival-time data obtained at a nation-wide seismograph network in Japan. Arrival-time data were produced from 8911 earthquakes and 188 stations, and comprised 247,504 P waves and 196,057 S waves, with differential data of 1,608,230 for P waves and 1,114,068 for S waves. Grid intervals were set at 10-20 km in the along-arc direction, 5-10 km perpendicular to the arc, and 5-10 km in the vertical direction The final results were obtained after eight iterations, which reduced the travel-time residual from 0.17 s to 0.11 s for P waves, and from 0.33 s to 0.19 s for S waves. The results show a low-velocity zone around the focal area of the M7.1 event, and that the aftershock activity is limited to the upper 15 km of the oceanic mantle. The lateral extent of the low-velocity zone is comparable to the distribution of aftershocks, suggesting a concentration of fluids in the aftershock area. The angle between the aftershock alignment and the dip of the slab surface is estimated to be ~60°, which is consistent with the dip of an oceanward-dipping normal fault observed at the outer-trench slope. These observations suggest that the M7.1 intraslab event occurred as a result of reactivation of a buried hydrated fault that formed prior to subduction. The upper ~15 km of the oceanic mantle may be locally hydrated by bending-related tensional faulting at the outer-trench slope.

The Influence of Upward Groundwater between Joints on the Stability and the Behavior of Dip Slope Failures

NASA Astrophysics Data System (ADS)

Weng, C. H.; Lin, M. L.; Hsieh, P. C.

2016-12-01

In recent years, landslides have attracted much attention in the engineering field in Taiwan. As previous studies, landslides are induced by earthquakes, rainfall, and groundwater. That groundwater flows into upper layer through vertical joints, upward groundwater, erodes the slope and reduces its stability. Nevertheless, in the literature, the impact of upward groundwater to the location of sliding surface and the behaviors of dip slope failure has not be investigated. In this study, physical model tests with water flow inclinometers are used to investigate the kinematics of dip slope failures under various conditions and to identify the failure modes of specimens (Fig. 1). Besides, the mechanics of one landslide case owing to upward groundwater is studied by numerical simulation. In the physical tests, the effects of upward groundwater on slope stability are investigated with different angles of inclinometers, different position of joints on specimens and different locations of upward seepage. The test results suggest that the upward water pressure becomes lower when the number of joints increases. As the water pressure increases to 3.8 times the weight of one block of the specimen, the block will slide. Another, when the specimen is covered by one granular content layer (see Fig. 2), the failure surface tends to develop at the granular content layer, and its kinematics is similar to debris slide; when the clay seam is below of the specimen, the translational slide occurs along the bottom of the blocks. Moreover, one dip slope case, Taiwan's National Highway No. 3 landslide event, are studied by numerical simulation. According to the results, some points are concluded: water pressure makes tension cracks on the top of the vertical joints on weathered sandstones; with anchor attenuation, the sandstone moves downslope, which makes the shear strain of the slope toe region increases (see Fig. 3). If friction angle of the slope decreases, the slide surface occurs along the weak surface, and it develops to the toe of the slope.

The Role of Cooling in Pahohoe Emplacement on Planetary Surfaces.

NASA Technical Reports Server (NTRS)

Glaze, L. S.; Baloga, S. M.

2015-01-01

Abundant evidence is emerging that many lavas on Mars were emplaced as slow-moving pahoehoe flows. Models for such scenarios contrast sharply with those for steep-sloped applications where gravity is the dominant force. The mode of flow emplacement on low slopes is characterized by toe formation and inflation. In the latter phase of pahoehoe flow emplacement, stagnation, inflation, and toe formation are most closely tied to the final topography, dimensions, and morphologic features. This mode of emplacement is particularly relevant to the low slopes of planetary surfaces such as the plains of Mars, Io and the Moon.

Geological Development of the Izu-Bonin Forearc Since the Eocene Based on Biostratigraphic, Rock Magnetic, and Sediment Provenance Observations from IODP Expedition 352 Drill Cores

NASA Astrophysics Data System (ADS)

Petronotis, K. E.; Robertson, A.; Kutterolf, S.; Avery, A.; Baxter, A.; Schindlbeck, J. C.; Wang, K. L.; Acton, G.

2016-12-01

International Ocean Discovery Program (IODP) Expedition 352 recovered early Oligocene to recent sediments above Eocene igneous basement at 4 sites in the Izu-Bonin Forearc. The sites were selected to investigate the forearc region since subduction initiation in the Eocene, with Sites U1439 and U1442 being cored into the upper trench slope and Sites U1440 and U1441 into the lower trench slope. Postcruise studies of biostratigraphy, sediment chemistry, tephra composition and chronology and magnetic properties, along with observations from prior coring help constrain the regional geological development. Volcanic activity in the area, as inferred from its influence on sediment composition, has varied between long periods of activity and quiescence. Combined whole-rock sediment chemistry and tephra compositions suggest that during the Oligocene to earliest Miocene ( 30-22 Ma) tuffaceous input of predominantly dacitic composition was mainly derived from the intra-oceanic Izu-Bonin Arc. The early Miocene interval ( 22-15 Ma) lacks tuffaceous input, as supported by rock magnetic data. During this period, the forearc subsided beneath the carbonate compensation depth (CCD), as evidenced by radiolarian-bearing mud and metal-rich silty clay. This was followed by input of tephra with bimodal felsic and mafic compositions from the Izu-Bonin Arc from 15 to 5 Ma. Middle Miocene to Quaternary time was characterized by increased carbonate preservation, coupled with abundant, predominantly felsic tephra input, which is chemically indicative of a Japan continental arc source (Honshu), with additional chemically distinctive input from the Izu-Bonin Arc. Extending back to 32 Ma, tephra layers can be correlated between the upper-slope sites, extrapolated to the less well-dated lower-slope sites, and further correlated with onland Japanese tephra (Kutterolf et al., 2016; Goldschmidt Conference). Overall, the new results provide an improved understanding of the regional tectonic evolution.

Landslide Hazard Map of The Upper Tiber River Basin, Central Italy

NASA Astrophysics Data System (ADS)

Cardinali, M.; Carrara, A.; Guzzetti, F.; Reichenbach, P.

For the Upper Tiber River basin, which extends over 4000 km2 in Central Italy, a landslide hazard map was derived from a statistical model based on a mix of morpho- logical, lithological, structural and land use data. All these data were obtained from the analysis of different sets of aerial photographs, ranging in scale from 1:33,000 to 1:13,000, systematic field surveys and bibliographical information. Rock types were grouped in 37 units on the basis of the hard vs. soft rock percentage, as as- certained from photo-geological interpretation and field surveys. During the photo- interpretation, the spatial relations between bedding plane attitude and slope aspect were also systematically determined. The landslide inventory map recognised 17,600 slope-failures that cover nearly 12.5% of the basin area. Landslides, which are mainly slide flow slide earth-flow and compound or complex movements, were classified and mapped as shallow or deep seated. A DTM, with a grid resolution of 25x25 m, was derived from digitised contour lines of base topographic maps, 1:25,000.in scale. The basin was then automatically partitioned into nearly 16,000 main slope-units through a specifically-designed software module that, starting from a high quality DTM gen- erates fully connected and complementary drainage and divide networks and a wide spectrum of morphometric parameters. Main slope-units were then subdivided accord- ing to the major rock types cropping out in the basin generating over 28,700 hydro- morphological-lithological terrain-units. Using the presence/absence of landslide in each terrain unit, as the grouping variable, a stepwise discriminant function was ap- plied to the terrain units. of the 50 variables entered into the discriminant function, 15 are lithological, 15 morphological, 11 express the structural setting or bedding plane attitude, 7 refer to land use and the last 2 reflect local climatic conditions. The model proved to be capable of correctly classifying as stable or unstable over 75% of the terrain units.

Seismic stratigraphy and tomography in the outer shelf and slope of the Central Basin, Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Kim, Sookwan; De Santis, Laura; Böhm, Gualtiero; Kuk Hong, Jong; Jin, Young Keun; Geletti, Riccardo; Wardell, Nigel; Petronio, Lorenzo; Colizza, Ester

2014-05-01

The Ross Sea, located between Victoria Land and Marie Byrd Land in Antarctica, is one of the main drainage of the Antarctic Ice Sheet (AIS). Reflection seismic data acquired by many countries during several decades have provided insights into the history of the Ross Sea and the AIS evolution. However the majority of the existing seismic data are concentrated in the shelf area, where hiatus formed by grounding ice sheet erosion multiple events prevent to reconstruct the entire sedimentary sequences depositional evolution. On the outer shelf and upper slope, the sedimentary sequences are relatively well preserved. The main purpose of this study is the investigation of the Cenozoic Antarctic Ice Sheet evolution through the seismic sequence analysis of the outer shelf and slope of the Central Basin, in the Ross Sea. The data used are the new multi-channel seismic data, KSL12, were acquired on the outer shelf and upper slope of the Central Bain in February 2013 by Korea Polar Research Institute. The reflection seismic data, previously collected by the Italian Antarctic Program (PNRA) and other data available from the Seismic Data Library System (SDLS) are also used for velocity tomography and seismic sequence mapping. The seismic data were processed by a conventional processing flow to produce the seismic profiles. Preliminary results show well-developed prograding wedges at the mouth of glacial troughs, eroded by a major glacial unconformity, the Ross Sea Unconformity 4 (RSU-4), correlated to a main event between early- and mid-Miocene. The velocity anomalies shown along KSL12-1 can be interpreted as showing the occurrence of gas and fluids, diagenetic horizons and sediment compactions. The isopach maps of each sequence show the variation of thickness of the sediments depocenter shift. The seismic sequence stratigraphy and acoustic facies analysis provide information about different phases of ice sheet's advance and retreat related to the AIS Cenozoic dynamics.

Interesting insights into instability of slopes and rock fall in the morphodynamic Himalayan terrane

NASA Astrophysics Data System (ADS)

Singh, T. N.; Vishal, V.; Pradhan, S. P.

2015-12-01

Himalayan mountain ranges are tectonically and seismically very active and experience many disastrous events with time due to slope failure. Frequent failures of rock cut slopes cause obstruction in traffic and often lead to fatalities. In recent years, the number of tragedies has increased when associated with regional phenomena such at the Kedarnath tragedy of 2013 and the Gorkha earthquake of 2015. The influence of such phenomena on the stability of slopes along important national highways and key settlement areas only raise the risk to lives and property. We conducted a multi-approach investigation for some key slopes along the National Highway 58 in Uttarakhand Himalaya, India. A very detailed field work was conducted to identify the unstable slopes and those with some history of failure. The pertinent geomechanical characteristics of the representative rock samples were determined in the laboratory. Based on the structural data, kinematic analysis was carried out. Finally the slopes were simulated using FDM based simulator, Flac/Slope for analysing the health of the slopes and Rockfall 4.0 to investigate the phenomenon of rockfall along the Highway. It was found that few slopes were weak due to the inherent weak rock materials while few slopes made up of high strength rocks were effectively weak due to prone-to-failure orientation of the joints. Quantification of bounce-height of rock blocks during fall, their energy, velocity and displacement along the slope was also done. Using 3-D simulations, few critically-stable slopes that appear to be stable, were identified. Little ground movement could be capable of triggering a large scale failure in the area. Slopes in the studied region are under threat to failure and need immediate proper planning using the suggested remedial measures.

An engineering rock classification to evaluate seismic rock-fall susceptibility and its application to the Wasatch Front

USGS Publications Warehouse

Harp, E.L.; Noble, M.A.

1993-01-01

Investigations of earthquakes world wide show that rock falls are the most abundant type of landslide that is triggered by earthquakes. An engineering classification originally used in tunnel design, known as the rock mass quality designation (Q), was modified for use in rating the susceptibility of rock slopes to seismically-induced failure. Analysis of rock-fall concentrations and Q-values for the 1980 earthquake sequence near Mammoth Lakes, California, defines a well-constrained upper bound that shows the number of rock falls per site decreases rapidly with increasing Q. Because of the similarities of lithology and slope between the Eastern Sierra Nevada Range near Mammoth Lakes and the Wasatch Front near Salt Lake City, Utah, the probabilities derived from analysis of the Mammoth Lakes region were used to predict rock-fall probabilities for rock slopes near Salt Lake City in response to a magnitude 6.0 earthquake. These predicted probabilities were then used to generalize zones of rock-fall susceptibility. -from Authors

Variations of cervical lordosis and head alignment after pedicle subtraction osteotomy surgery for sagittal imbalance.

PubMed

Cecchinato, R; Langella, F; Bassani, R; Sansone, V; Lamartina, C; Berjano, P

2014-10-01

The variations of the cervical lordosis after correction of sagittal imbalance have been poorly studied. The aim of our study is to verify whether the cervical lordosis changes after surgery for sagittal imbalance. Thirty-nine patients were included in the study. Cervical, thoracic and lumbar spine, pelvic and lower-limb sagittal parameters were recorded. The cranial alignment was measured by the newly described Cranial Slope. The global cervical kyphosis (preop -43°, postop -31.5°) and the upper (preop -24.1°, postop -20.2°) and lower cervical kyphosis (preop -18.1°, postop -9.2°) were significantly reduced after surgical realignment of the trunk. A positive linear correlation was observed between the changes in T1 slope and the lower cervical lordosis, and between T1 slope and the global cervical alignment. The cervical lordosis is reduced by surgical correction of malalignment of the trunk, suggesting an adaptive role to maintain the head's neutral position.

Small scale turbidity currents in a tectonically active submarine graben, the Gulf of Corinth (Greece): their significance in dispersing mine tailings and their relevance to basin filling

NASA Astrophysics Data System (ADS)

Papatheodorou, G.; Stefatos, A.; Christodoulou, D.; Ferentinos, G.

2003-04-01

The Gulf of Corinth is an intra-plate active graben within the Aegean microplate, which is characterized by high frequency occurrence of gravitative mass movements. A detailed marine survey in Antikyra bay, on the northern margin of the graben, was carried out (i) to study the bathymetry and morphology of the seafloor and (ii) to examine the distribution and dispersion of bauxite “red-mud” tailings and the formation of present-day fine grained, thin bedded turbidites. The examination of high resolution seismic profiles has shown that the northern flank of the gulf of Corinth consists of the shelf, slope and basin floor. The shelf has an average width of 10 km and dips very gently at a gradient less than 1.2o to a depth of 300m. The slope extends from the 300m to the 700m isobath with a gradient ranging from 5o to 7.5o. The basin floor deeper than the 700m isobath is flat with a gradient less than 0.1o. The shelf break and upper slope are affected by mass-movements. The seafloor on slope is incised by numerous channels trending in a NNE-SSW direction. The floor of the plain is covered by ponded turbidites. The analysis of cores based on (i) the texture and the structure of the individual layers of the surficial sedimentary cover and (ii) the tracing of bauxite red-mud tailing which have been discharged since 1970 on the upper shelf of the Antikyra Bay, have shown that: (i) Shelf and upper slope sediments are transported to the basin floor by turbidity flows. (ii) The slope surface is affected by the erosional action of the turbidity currents. (iii) The basin floor is covered by thin-bedded fine-grained turbidites whose thickness ranges from 0.8-4 cm. (iv) The individual turbidite beds, which consist of silt and clay, are structureless and are separated by sharp, planar or erosional contacts. (v) Hemipelagic intercalations are absent. The number of turbiditic events recorded in the surveyed area is from 2-5 events over a period of 15 years or 122 to 333 events per 1000 years. Each turbidite is usually lobe shaped and has an areal coverage from 4 to 12 km2. The turbidites overlap and cover a total area of 48 km2. The total thickness of the turbidites deposited during this period was between 5 and 12 cm which indicate sedimentation rates from 320 to 800 cm per 1000 years. The turbidites form a sedimentary body over the surveyed area whose volume is conservatively estimated at 35 x 10-5 km3. The high sedimentation rates and the high frequency of turbiditic events suggest that they play an important role in the filling of seismically active basins and that their volumetric contribution to basin infill is comparable to that of megaturbidites.

Upper limb function in Duchenne muscular dystrophy: 24 month longitudinal data.

PubMed

Pane, Marika; Coratti, Giorgia; Brogna, Claudia; Mazzone, Elena Stacy; Mayhew, Anna; Fanelli, Lavinia; Messina, Sonia; D'Amico, Adele; Catteruccia, Michela; Scutifero, Marianna; Frosini, Silvia; Lanzillotta, Valentina; Colia, Giulia; Cavallaro, Filippo; Rolle, Enrica; De Sanctis, Roberto; Forcina, Nicola; Petillo, Roberta; Barp, Andrea; Gardani, Alice; Pini, Antonella; Monaco, Giulia; D'Angelo, Maria Grazia; Zanin, Riccardo; Vita, Gian Luca; Bruno, Claudio; Mongini, Tiziana; Ricci, Federica; Pegoraro, Elena; Bello, Luca; Berardinelli, Angela; Battini, Roberta; Sansone, Valeria; Albamonte, Emilio; Baranello, Giovanni; Bertini, Enrico; Politano, Luisa; Sormani, Maria Pia; Mercuri, Eugenio

2018-01-01

The aim of the study was to establish 24 month changes in upper limb function using a revised version of the performance of upper limb test (PUL 2.0) in a large cohort of ambulant and non-ambulant boys with Duchenne muscular dystrophy and to identify possible trajectories of progression. Of the 187 patients studied, 87 were ambulant (age range: 7-15.8 years), and 90 non-ambulant (age range: 9.08-24.78). The total scores changed significantly over time (p<0.001). Non-ambulant patients had lower total scores at baseline (mean 19.7) when compared to the ambulant ones (mean 38.4). They also had also a bigger decrease in total scores over 24 months compared to the ambulant boys (4.36 vs 2.07 points). Multivariate model analysis showed that the Performance of Upper Limb changes reflected the entry level and ambulation status, that were independently associated to the slope of Performance of Upper Limb changes. This information will be of help both in clinical practice and at the time of designing clinical trials.

Numerical modelling of convective heat transport by air flow in permafrost talus slopes

NASA Astrophysics Data System (ADS)

Wicky, Jonas; Hauck, Christian

2017-06-01

Talus slopes are a widespread geomorphic feature in the Alps. Due to their high porosity a gravity-driven internal air circulation can be established which is forced by the gradient between external (air) and internal (talus) temperature. The thermal regime is different from the surrounding environment, leading to the occurrence of permafrost below the typical permafrost zone. This phenomenon has mainly been analysed by field studies and only few explicit numerical modelling studies exist. Numerical simulations of permafrost sometimes use parameterisations for the effects of convection but mostly neglect the influence of convective heat transfer in air on the thermal regime. In contrast, in civil engineering many studies have been carried out to investigate the thermal behaviour of blocky layers and to improve their passive cooling effect. The present study further develops and applies these concepts to model heat transfer in air flows in a natural-scale talus slope. Modelling results show that convective heat transfer has the potential to develop a significant temperature difference between the lower and the upper parts of the talus slope. A seasonally alternating chimney-effect type of circulation develops. Modelling results also show that this convective heat transfer leads to the formation of a cold reservoir in the lower part of the talus slope, which can be crucial for maintaining the frozen ground conditions despite increasing air temperatures caused by climate change.

Purely Dry Mergers do not Explain the Observed Evolution of Massive Early-type Galaxies since z ~ 1

NASA Astrophysics Data System (ADS)

Sonnenfeld, Alessandro; Nipoti, Carlo; Treu, Tommaso

2014-05-01

Several studies have suggested that the observed size evolution of massive early-type galaxies (ETGs) can be explained as a combination of dry mergers and progenitor bias, at least since z ~ 1. In this paper we carry out a new test of the dry-merger scenario based on recent lensing measurements of the evolution of the mass density profile of ETGs. We construct a theoretical model for the joint evolution of the size and mass density profile slope γ' driven by dry mergers occurring at rates given by cosmological simulations. Such dry-merger model predicts a strong decrease of γ' with cosmic time, inconsistent with the almost constant γ' inferred from observations in the redshift range 0 < z < 1. We then show with a simple toy model that a modest amount of cold gas in the mergers—consistent with the upper limits on recent star formation in ETGs—is sufficient to reconcile the model with measurements of γ'. By fitting for the amount of gas accreted during mergers, we find that models with dissipation are consistent with observations of the evolution in both size and density slope, if ~4% of the total final stellar mass arises from the gas accreted since z ~ 1. Purely dry merger models are ruled out at >99% CL. We thus suggest a scenario where the outer regions of massive ETGs grow by accretion of stars and dark matter, while small amounts of dissipation and nuclear star formation conspire to keep the mass density profile constant and approximately isothermal.

2 - 4 million years of sedimentary processes in the Labrador Sea: implication for North Atlantic stratigraphy

NASA Astrophysics Data System (ADS)

Mosher, D. C.; Saint-Ange, F.; Campbell, C.; Piper, D. J.

2012-12-01

Marine sedimentary records from the western North Atlantic show that a significant portion of sediment deposited since the Pliocene originated from the Canadian Shield. In the Labrador Sea, previous studies have shown that bottom currents .strongly influenced sedimentation during the Pliocene, while during the Quaternary, intensification of turbidity current flows related to meltwater events were a dominant factor in supplying sediment to the basin and in the development of the North Atlantic Mid-Ocean Channel (NAMOC). Despite understanding this general pattern of sediment flux, details regarding the transfer of sediment from the Labrador Shelf to deep water and from the Labrador Sea to the North Atlantic remain poorly understood. Our study focuses on sedimentary processes occurring along the Labrador margin since the Pliocene and their consequences on the margin architecture, connection to the NAMOC, and role in sediment flux from the Labrador basin to the Sohm Abyssal Plain. Piston core and high resolution seismic data reveal that during the Pliocene to mid Pleistocene, widespread slope failures led to mass transport deposition along the entire Labrador continental slope. After the mid Pleistocene, sedimentation along the margin was dominated by the combined effects of glaciation and active bottom currents. On the shelf, prograded sedimentary wedges filled troughs and agraded till sheets form intervening banks. On the slope, stacked glaciogenic fans developed seaward of transverse troughs between 400 and 2800 mbsl. On the lower slope, seismic data show thick sediment drifts capped by glacio-marine mud. This unit is draped by well stratified sediment and marks a switch from a contourite dominated regime to a turbidite dominated regime. This shift occurred around 0.5 - 0.8 ka and correlates to the intensification of glaciations. Late Pleistocene sediments on the upper slope consist of stratified sediments related to proglacial plume fall-out. Coarse grained sediments, other than ice rafted detritus, by-passed the upper and middle slope and were transported to the lower slope and deep ocean. Seismic profiles and multibeam data along the Labrador Slope show a complex network of channels, with wide flat-bottomed channels off Saglek Bank to narrow channels off Cartwright Bank. The channels merge around 3000 mbsl to form single wide (~20 km) channels that eventually intersect, or flow parallel to the NAMOC. Rapid development of the NAMOC from the mid to late Pleistocene affected depositional patterns for sediment sourced from the Labrador margin. Downslope-transported sediment from the Labrador margin mostly tends to fill the basin or feed into NAMOC through tributary systems, whereas sediments derived from Hudson Strait feed the NAMOC and eventually the Sohm Abyssal plain. Sediment transported southward by the Western Boundary Undercurrent and Labrador Current likely reflect input along the margin, from Hudson Strait to Orphan Basin. Turbidite spill-over deposits are observed onlapping the continental margin of Labrador and Newfoundland as far south as Newfoundland Ridge.

Depositional and deformational history of the Franciscan complex, northernmost California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aalto, K.R.

1990-05-01

Pervasive extensional shear fractures and curvilinear arrays of clay and silt-filled veins in Franciscan Complex melanges and turbidites formed when Franciscan sediments were unlithified. Sandstone dikes both crosscut and follow fractures. Several scales of extensional faulting account for the juxtaposition of turbidites of different facies and/or with varying degrees of stratal disruption, the formation of sandstone lozenges and pinch-and-swell structures, and the formation of scaly foliation within the matrix of melange units. Within turbidites, the upper laminated portions of beds commonly contain abundant listric microfaults and the more massive lower portions of beds contain sediment-filled vein arrays. Veining and faultingmore » occurred concurrently and resulted in differential extension of upper verses lower portions of beds. The finer sediment in veins reflects both cataclasis and filtering in of clay and silt from vein walls. Most Franciscan rocks record an early pervasive, layer-parallel flattening strain, which may be related to the gravitational collapse of late Mesozoic Franciscan inner trench slope sediments that accompanied accretionary prism expansion resulting from underplating. However, some turbidites record noncoaxial extension that resulted from downslope creep of sediments. At Crescent City, sediment creep resulted in oversteepening of the Franciscan inner trench slope, which, in turn, may have triggered large-scale failure of slope materials resulting in the emplacement of the Crescent City olistostrome. The olistostrome crops out for 12 km along the coast, is up to 600 m thick, is in depositional contact with turbidites, and contains chiefly sandstone, greenstone, chert olistoliths up to 200 m across, and zones of slump-folded turbidites.« less

Depositional history of Louisiana-Mississippi outer continental shelf

USGS Publications Warehouse

Kindinger, J.L.; Miller, R.J.; Stelting, C.E.

1982-01-01

A geological study was undertaken in 1981 in the Louisiana-Mississippi outer continental shelf for the Bureau of Land Management. The study included a high-resolution seismic reflection survey, surficial sediment sampling and surface current drifter sampling. Approximately 7100 sq km of the Louisiana-Mississippi shelf and upper slope were surveyed. The sea floor of the entire area is relatively smooth except for occasional areas of uplift produced by diapiric intrusion along the upper slope. Characteristics of the topography and subsurface shelf sediments are the result of depositional sequences due to delta outbuilding over transgressive sediments with intervening periods of erosion during low sea level stands. Little evidence of structural deformation such as faults, diapirs, and shallow gas is present on the shelf and only a few minor faults and scarps are found on the slope. Minisparker seismic records in combination with air gun (40 and 5 cu in) and 3.5-kHz subbottom profile records reveal that seven major stages of shelf development have occurred since the middle Pleistocene. The shelf development has been controlled by the rise and fall of sea level. These stages are defined by four major unconformities, several depositions of transgressive sediments, sequences of river channeling and progradational delta deposits. Surficial sediment sample and seismic records indicate tat the last major depositional event was the progradation of the St. Bernard Delta lobe. This delta lobe covered the northwestern and central regions. Surficial sediments in most of the study area are the product of the reworking of the San Bernard Delta lobe and previous progradations.

Asian Summer Monsoon Anomalies Induced by Aerosol Direct Forcing: The Role of the Tibetan Plateau

NASA Technical Reports Server (NTRS)

Lau, K. M.; Kim, M. K.; Kim, K. M.

2006-01-01

In this paper we present results of a numerical study using the NASA finite-volume GCM to elucidate a plausible mechanism for aerosol impact on the Asian summer monsoon involving interaction with physical processes over the Tibetan Plateau (TP). During the premonsoon season of March April, dusts from the deserts of western China, Afghanistan/Pakistan, and the Middle East are transported into and stacked up against the northern and southern slopes of the TP. The absorption of solar radiation by dust heats up the elevated surface air over the slopes. On the southern slopes, the atmospheric heating is reinforced by black carbon from local emission. The heated air rises via dry convection, creating a positive temperature anomaly in the mid-to-upper troposphere over the TP relative to the region to the south. In May through early June in a manner akin to an elevated heat pump , the rising hot air forced by the increasing heating in the upper troposphere, draws in warm and moist air over the Indian subcontinent, setting the stage for the onset of the South Asia summer monsoon. Our results suggest that increased dust loading coupled with black carbon emission from local sources in northern India during late spring may lead to an advance of the rainy periods and subsequently an intensification of the Indian summer monsoon. The enhanced rainfall over India is associated with the development of an aerosol-induced large-scale sea level pressure anomaly pattern, which causes the East Asia (Mei-yu) rain belt to shift northwestward, suppressing rainfall over East Asia and the adjacent oceanic regions.

Stratigraphic architecture and depositional history of lower Miocene, Planulina Zone, Southern Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gates, B.C.; Galloway, W.E.

1988-01-01

The Planulina zone is a wedge of clastic sediment positioned between the Anahuac shale below and the Oakville sandstone interval above. Planulna sediments were deposited on an erosional surface, during a general rise in the sea level, and formed a retrogradational wedge. Within the study area, the Planulina zone consists of two large depositional complexes: the Mud Lake complex in west Cameron Parish, Louisiana, and the East Cameron complex in east Cameron Parish. The lowermost depositional sequence in the East Cameron complex is preserved in a network of submarine canyons that were eroded into the upper slope. Framework sands weremore » deposited in channel systems confined to the axis of the canyons, and the sands are encased in marine shale containing benthonic foraminifera indicative of an upper to middle slope paleoenvironment. Two younger depositional sequences overlie the submarine canyon facies and were deposited by deltaic systems that prograded basinward. A zone of expansion extends east to west through the Planulina interval and is named the ''Planulina flexure.'' The flexure is a large fault located at the relict shelf edge and soles out downdip inn the Anahuac shale. Several thousand feet of sediment downthrown on the flexure is equivalent to several hundred feet upthrown, and the flexure represented the boundary dividing updip deltaic processes from downdip slope processes during the beginning of Planulina deposition. The Planulina depositional history and stratigraphic architecture are directly related to the displacement along the flexure and the structural deformation of the underlying Anahuac shale.« less

Observations of a free-energy source for intense electrostatic waves. [in upper atmosphere near upper hybrid resonance frequency

NASA Technical Reports Server (NTRS)

Kurth, W. S.; Frank, L. A.; Gurnett, D. A.; Burek, B. G.; Ashour-Abdalla, M.

1980-01-01

Significant progress has been made in understanding intense electrostatic waves near the upper hybrid resonance frequency in terms of the theory of multiharmonic cyclotron emission using a classical loss-cone distribution function as a model. Recent observations by Hawkeye 1 and GEOS 1 have verified the existence of loss-cone distributions in association with the intense electrostatic wave events, however, other observations by Hawkeye and ISEE have indicated that loss cones are not always observable during the wave events, and in fact other forms of free energy may also be responsible for the instability. Now, for the first time, a positively sloped feature in the perpendicular distribution function has been uniquely identified with intense electrostatic wave activity. Correspondingly, we suggest that the theory is flexible under substantial modifications of the model distribution function.

A reappraisal of success factors for Olympic cross-country skiing.

PubMed

Sandbakk, Øyvind; Holmberg, Hans-Christer

2014-01-01

Cross-country (XC) skiing has been an Olympic event since the first Winter Games in Chamonix, France, in 1924. Due to more effective training and tremendous improvements in equipment and track preparation, the speed of Olympic XC-ski races has increased more than that of any other Olympic endurance sport. Moreover, pursuit, mass-start, and sprint races have been introduced. Indeed, 10 of the 12 current Olympic competitions in XC skiing involve mass starts, in which tactics play a major role and the outcome is often decided in the final sprint. Accordingly, reappraisal of the success factors for performance in this context is required. The very high aerobic capacity (VO2max) of many of today's world-class skiers is similar that of their predecessors. At the same time, the new events provide more opportunities to profit from anaerobic capacity, upper-body power, high-speed techniques, and "tactical flexibility." The wide range of speeds and slopes involved in XC skiing requires skiers to continuously alternate between and adapt different subtechniques during a race. This technical complexity places a premium on efficiency. The relative amounts of endurance training performed at different levels of intensity have remained essentially constant during the past 4 decades. However, in preparation for the Sochi Olympics in 2014, XC skiers are performing more endurance training on roller skis on competition-specific terrain, placing greater focus on upper-body power and more systematically performing strength training and skiing at high speeds than previously.

Metamorphic Mountain, Mount Jefferson State Park: An Environmental Education Learning Experience Designed for Grades 5-7.

ERIC Educational Resources Information Center

Pittman, George K., II; Hubbard, William F.; Lambert, Michael D.; Beazley, Lea J.

Mount Jefferson State Natural Area is located in the southern Blue Ridge highlands of North Carolina and covers 489 acres, which includes peaks and upper slopes to the Mount Jefferson mountain. This document introduces students to the geology of Mount Jefferson State Park and focuses on the geologic processes and rocks and minerals of Mount…

Performance Evaluation of Advanced Retrofit Roof Technologies Using Field-Test Data Phase Three Final Report, Volume 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Childs, Phillip W.; Atchley, Jerald Allen

2015-01-01

This article presents some miscellaneous data from two low-slope and two steep-slope experimental roofs. The low-slope roofs were designed to compare the performance of various roof coatings exposed to natural weatherization. The steep-slope roofs contained different combinations of phase change material, rigid insulation, low emittance surface and above-sheathing ventilation, with standing-seam metal panels on top. The steep-slope roofs were constructed on a series of adjacent attics separated at the gables using thick foam insulation. This article describes phase three (3) of a study that began in 2009 to evaluate the energy benefits of a sustainable re-roofing technology utilizing standing-seam metalmore » roofing panels combined with energy efficient features like above-sheathing-ventilation (ASV), phase change material (PCM) and rigid insulation board. The data from phases 1 and 2 have been previously published and reported [Kosny et al., 2011; Biswas et al., 2011; Biswas and Childs, 2012; Kosny et al., 2012]. Based on previous data analyses and discussions within the research group, additional test roofs were installed in May 2012, to test new configurations and further investigate different components of the dynamic insulation systems. Some experimental data from phase 3 testing from May 2012 to December 2013 and some EnergyPlus modeling results have been reported in volumes 1 and 3, respectively, of the final report [Biswas et al., 2014; Biswas and Bhandari, 2014].« less

The carcinogenic potencies of 2,3,7,8-tetrachlorodibenzo-p-dioxin: Letting the data speak for themselves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Green, L.C.; Crouch, E.A.C.; Lester, R.R.

1996-12-31

The authors analyze here the dose-response data generated from the seminal bioassay of 2,3,7,8-tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD) in Sprague-Dawley rats, reported by Kociba and coworkers. That chronic toxicity and oncogenicity study showed 2,3,7,8-TCDD to increase the incidence of certain tumors, while decreasing the incidence of others. Further, results in female rats were markedly different from those in male rats--a result ascribed to the dependence of dioxin on estrogen for some of its toxic effects. For each sex, the authors analyze each tumor type on which 2,3,7,8-TCDD has, or might have, an effect, whether positive, negative, or neutral. After generating dose-response relationships formore » each tumor type, the authors combine them. The combination involves simply adding the slopes of each tumor-specific dose-response relationship. They perform separate analyses for each set of dose-ranges. They also calculate upper (and lower) bounds on the maximum likelihood estimates, using the upper 95th percentile estimates for the slopes of the net dose-response relationships as conservative estimates of carcinogenic potency.« less

Integrated satellite InSAR and slope stability modeling to support hazard assessment at the Safuna Alta glacial lake, Peru

NASA Astrophysics Data System (ADS)

Cochachin, Alejo; Frey, Holger; Huggel, Christian; Strozzi, Tazio; Büechi, Emanuel; Cui, Fanpeng; Flores, Andrés; Saito, Carlos

2017-04-01

The Safuna glacial lakes (77˚ 37' W, 08˚ 50' S) are located in the headwater of the Tayapampa catchment, in the northernmost part of the Cordillera Blanca, Peru. The upper lake, Laguna Safuna Alta at 4354 m asl has formed in the 1960s behind a terminal moraine of the retreating Pucajirca Glacier, named after the peak south of the lakes. Safuna Alta currently has a volume of 15 x 106 m3. In 2002 a rock fall of several million m3 from the proximal left lateral moraine hit the Safuna Alta lake and triggered an impact wave which overtopped the moraine dam and passed into the lower lake, Laguna Safuna Baja, which absorbed most of the outburst flood from the upper lake, but nevertheless causing loss in cattle, degradation of agricultural land downstream and damages to a hydroelectric power station in Quitaracsa gorge. Event reconstructions showed that the impact wave in the Safuna Alta lake had a runup height of 100 m or more, and weakened the moraine dam of Safuna Alta. This fact, in combination with the large lake volumes and the continued possibility for landslides from the left proximal moraine pose a considerable risk for the downstream settlements as well as the recently completed Quitaracsa hydroelectric power plant. In the framework of a project funded by the European Space Agency (ESA), the hazard situation at the Safuna Alta lake is assessed by a combination of satellite radar data analysis, field investigations, and slope stability modeling. Interferometric analyses of the Synthetic Aperture Radar (InSAR) of ALOS-1 Palsar-1, ALOS-2 Palsar-2 and Sentinel-1 data from 2016 reveal terrain displacements of 2 cm y-1 in the detachment zone of the 2002 rock avalanche. More detailed insights into the characteristics of these terrain deformations are gained by repeat surveys with differential GPS (DGPS) and tachymetric measurements. A drone flight provides the information for the generation of a high-resolution digital elevation model (DEM), which is used for the modeling of the geomechanical slope stability using the W/Slope and UDEC models. Model application, however, is limited due to data scarcity regarding geotechnical slope properties, which needed to be estimated. The combination of these data products, measurements and model results provide important information for the estimation of potential source areas for future slope collapses and involved volumes. Eventually, such information can be used for the definition of possible rock avalanche scenarios and related chain reactions in order to elaborate a hazard map for resulting lake outburst floods. At the same time, the potential for an operational slope stability monitoring system at this site will be evaluated.

Assessment of sediment sources throughout the proglacial area of a small Arctic catchment based on high-resolution digital elevation models

NASA Astrophysics Data System (ADS)

Kociuba, Waldemar

2017-06-01

The article presents calculations of quantitative modifications of the morphology of selected subsystems of a glacial valley through: (i) identification of the spatial distribution of important sources of sediment, (ii) assessment of the spatiotemporal variety of sediment volume and landform morphology, and (iii) assessment of the role of particular subsystems in sediment distribution. The study involved a comparison of the results of field measurements from 2010 to 2013 performed in the Scott Glacier catchment (10.1 km2) in NW Wedel Jarlsberg Land (Spitsbergen). The assessment of the landform surface changes was performed by means of a precise Terrestrial Laser Scanning (TLS) survey. The applied field and post-processing techniques for oblique laser scanning permitted the acquisition of digital elevation data at a resolution 0.01 m and density > 500 pt m- 2. This allowed the development of a detailed terrain model, and balancing spatial quantitative changes in six research test areas (10,000 m2) located within two subsystems of the catchment in a cascade arrangement. In the alluvial valley-floor subsystem, the survey covered: 1) the glacier terminus, 2) the intramarginal outwash plain, 3) the extramarginal braid-plain and 4) the alluvial fan, and in the slope subsystem: 5) the erosional-depositional slope in the gorge through terminal moraines, and 6) the solifluction slope. Three zones differing in terms of the spatiotemporal dynamics of geomorphic processes were distinguished within the two analysed valley subsystems. In the valley floor subsystem, these are: (i) the zone of basic supply (distribution throughout the melting season) and (ii) the redeposition zone (distribution particularly during floods), and in the slope subsystem: (iii) zone of periodical supply (distributed mainly in periods of increased precipitation and rapid increases in temperature in summer and during snow avalanches in winter). The glacier and the landforms of the channel and valley floor, as well as slope sediments transported as a result of mass wasting processes and activity of the active permafrost layer, constitute important sources of sediment supply over a short/3-year timescale. Evidence of major changes of the surface morphology (slopes, floodplain and channel platform) resulted in varied sediment budgets. The subtraction of consecutive DEMs of the test areas located in the alluvial valley subsystem revealed downstream spatial and volumetric differentiation, from the predominance of erosion (79% of volume; 43% of area) to the dominance of deposition (90/91%, respectively) in upper part of the valley floor to erosion predominance in the central (88/95%) and lower (87/82%) part of valley floor. The test areas located on the slope subsystem showed the opposite relationship: deposition dominance (88% of volume; 80% of area) in the upper gorge and erosion dominance (99/99%, respectively) in the lower part (solifluction slopes). The analysis of short-time repeated surveys (3-week survey) where volumes were calculated following DEM subtraction showed increased deposition (82% of volume; 79% of area) for the alluvial fan, and for solifluction slopes (70/57%, respectively).

Submarine slope failures along the convergent continental margin of the Middle America Trench

NASA Astrophysics Data System (ADS)

Harders, Rieka; Ranero, CéSar R.; Weinrebe, Wilhelm; Behrmann, Jan H.

2011-06-01

We present the first comprehensive study of mass wasting processes in the continental slope of a convergent margin of a subduction zone where tectonic processes are dominated by subduction erosion. We have used multibeam bathymetry along ˜1300 km of the Middle America Trench of the Central America Subduction Zone and deep-towed side-scan sonar data. We found abundant evidence of large-scale slope failures that were mostly previously unmapped. The features are classified into a variety of slope failure types, creating an inventory of 147 slope failure structures. Their type distribution and abundance define a segmentation of the continental slope in six sectors. The segmentation in slope stability processes does not appear to be related to slope preconditioning due to changes in physical properties of sediment, presence/absence of gas hydrates, or apparent changes in the hydrogeological system. The segmentation appears to be better explained by changes in slope preconditioning due to variations in tectonic processes. The region is an optimal setting to study how tectonic processes related to variations in intensity of subduction erosion and changes in relief of the underthrusting plate affect mass wasting processes of the continental slope. The largest slope failures occur offshore Costa Rica. There, subducting ridges and seamounts produce failures with up to hundreds of meters high headwalls, with detachment planes that penetrate deep into the continental margin, in some cases reaching the plate boundary. Offshore northern Costa Rica a smooth oceanic seafloor underthrusts the least disturbed continental slope. Offshore Nicaragua, the ocean plate is ornamented with smaller seamounts and horst and graben topography of variable intensity. Here mass wasting structures are numerous and comparatively smaller, but when combined, they affect a large part of the margin segment. Farther north, offshore El Salvador and Guatemala the downgoing plate has no large seamounts but well-defined horst and graben topography. Off El Salvador slope failure is least developed and mainly occurs in the uppermost continental slope at canyon walls. Off Guatemala mass wasting is abundant and possibly related to normal faulting across the slope. Collapse in the wake of subducting ocean plate topography is a likely failure trigger of slumps. Rapid oversteepening above subducting relief may trigger translational slides in the middle Nicaraguan upper Costa Rican slope. Earthquake shaking may be a trigger, but we interpret that slope failure rate is lower than recurrence time of large earthquakes in the region. Generally, our analysis indicates that the importance of mass wasting processes in the evolution of margins dominated by subduction erosion and its role in sediment dynamics may have been previously underestimated.

Stressor Identification (Si) at Contaminated Sites: Upper Arkansas River, Colorado (Final)

EPA Science Inventory

EPA announced the availability of the final report, Stressor Identification (SI) at Contaminated Sites: Upper Arkansas River, Colorado. This report describes a causal assessment for impairments of plant growth and plant species richness at a terrestrial contaminated site ...

Analysis of Local Slopes at the InSight Landing Site on Mars

NASA Astrophysics Data System (ADS)

Fergason, R. L.; Kirk, R. L.; Cushing, G.; Galuszka, D. M.; Golombek, M. P.; Hare, T. M.; Howington-Kraus, E.; Kipp, D. M.; Redding, B. L.

2017-10-01

To evaluate the topography of the surface within the InSight candidate landing ellipses, we generated Digital Terrain Models (DTMs) at lander scales and those appropriate for entry, descent, and landing simulations, along with orthoimages of both images in each stereopair, and adirectional slope images. These products were used to assess the distribution of slopes for each candidate ellipse and terrain type in the landing site region, paying particular attention to how these slopes impact InSight landing and engineering safety, and results are reported here. Overall, this region has extremely low slopes at 1-meter baseline scales and meets the safety constraints of the InSight lander. The majority of the landing ellipse has a mean slope at 1-meter baselines of 3.2°. In addition, a mosaic of HRSC, CTX, and HiRISE DTMs within the final landing ellipse (ellipse 9) was generated to support entry, descent, and landing simulations and evaluations. Several methods were tested to generate this mosaic and the NASA Ames Stereo Pipeline program dem_mosaic produced the best results. For the HRSC-CTX-HiRISE DTM mosaic, more than 99 % of the mosaic has slopes less than 15°, and the introduction of artificially high slopes along image seams was minimized.

Analysis of local slopes at the InSight landing site on Mars

USGS Publications Warehouse

Fergason, Robin L.; Kirk, Randolph L.; Cushing, Glen; Galuszka, Donna M.; Golombek, Matthew P.; Hare, Trent M.; Howington-Kraus, Elpitha; Kipp, Devin M; Redding, Bonnie L.

2017-01-01

To evaluate the topography of the surface within the InSight candidate landing ellipses, we generated Digital Terrain Models (DTMs) at lander scales and those appropriate for entry, descent, and landing simulations, along with orthoimages of both images in each stereopair, and adirectional slope images. These products were used to assess the distribution of slopes for each candidate ellipse and terrain type in the landing site region, paying particular attention to how these slopes impact InSight landing and engineering safety, and results are reported here. Overall, this region has extremely low slopes at 1-meter baseline scales and meets the safety constraints of the InSight lander. The majority of the landing ellipse has a mean slope at 1-meter baselines of 3.2°. In addition, a mosaic of HRSC, CTX, and HiRISE DTMs within the final landing ellipse (ellipse 9) was generated to support entry, descent, and landing simulations and evaluations. Several methods were tested to generate this mosaic and the NASA Ames Stereo Pipeline program dem_mosaic produced the best results. For the HRSC-CTX-HiRISE DTM mosaic, more than 99 % of the mosaic has slopes less than 15°, and the introduction of artificially high slopes along image seams was minimized.

The Tsaoling 1941 Landslide, New Insight of Numerical Simulation of Discrete Element Model

NASA Astrophysics Data System (ADS)

Tang, C.-L.; Hu, J.-C.; Lin, M.-L.

2009-04-01

Large earthquakes in the southeastern Taiwan are not rare in the historical catalogue. Tsaoling, located southeast of Taiwan, last five large landslides occurred in the 19th and 20th centuries. According to the literature about the Tsaoling landslide, we concluded four characteristics of the Tsaoling landslide, (1) repeated (2) multi-landslide surface, (3) huge landslide block, and (4) some people survived after sliding a long distance (>2 km). This is the reason why we want to understand the causes of the repeated landslides in Tsaoling and its mechanisms. However, there is not any record about the landslide in 1862 and the most of the landslide evidence disappeared. Hence, we aim at the landslide dynamics of the 1941 landslide in this study. Tsaoling area is located in a large dipping towards the south-southwest monocline. The dip of strata toward the SSW is similar to the both sides of the Chinshui River valley. The bedrock of the Tsaoling area is Pliocene in age and belongs to the upper Chinshui Shale and the lower Cholan Formation. The plane failure analysis and Newmark displacement method are common for slope stability in recent years. However, the plane failure analysis can only provide a safety factor. When the safe factor (FS) is less than 1, it can only indicate that the slope is unstable. The result of Newmark displacement method is a value of displacement length. Both assumptions of the analysis are based on a rigid body. For the large landslide, like the Tsaoling landslide, the volume of landslide masses are over 108 m3, and the landslide block cannot be considered a rigid body. We considered the block as a quasi-rigid body, because the blocks are deformable and jointed. The original version of Distinct Element Method (DEM) was devoted to the modeling of rock-block systems and it was lately applied to the modeling of granular material. The calculation cycle in PFC2D is a time-stepping algorithm that consists of the repeated application of the law of motion to each particle, a force-displacement law to each contact, and a constant updating of wall positions. The physical properties of the particles in the model can be traced in time dominant (i.e. velocity, displacement, force, and stress). During the simulating, we can get the variation of physical properties, so the inter-block change of displacement, force, and stress could be monitored. After the seismic shaking, the result of the PFC model can be divided into three portions, upper (thick), middle (transitional) and lower (thin). The shear displacements of the three parts on the sliding plane are not agreement. The displacement of the lower part block is large than the upper and middle part of the blocks. The shear displacement of middle part is between upper and lower part. During the shaking of the earthquake, the different parts in the block collide with each other, and the upper part of the block was hit back and stayed in origin position or slid a short distance, but the lower part of the block was hit down by the upper block. The collision pushed down a certain length to the lower part of the block. The shear length just lost the strength of the sliding plane and induced the landslide during the 1941 earthquake. The upper part of the block stayed on the slope but revealed unstable. Eight months later, the upper part of the block slid down was induced by a 700 mm downpour in three days.

Sedimentary processes on the Atlantic Continental Slope of the United States

USGS Publications Warehouse

Knebel, H.J.

1984-01-01

Until recently, the sedimentary processes on the United States Atlantic Continental Slope were inferred mainly from descriptive studies based on the bathymetry and on widely spaced grab samples, bottom photographs, and seismic-reflection profiles. Over the past 6 years, however, much additional information has been collected on the bottom morphology, characteristics of shallow-subbottom strata, velocity of bottom currents, and transport of suspended and bottom sediments. A review of these new data provides a much clearer understanding of the kinds and relative importance of gravitational and hydrodynamic processes that affect the surface sediments. On the rugged slope between Georges Bank and Cape Lookout, N.C., these processes include: (1) small scale mass wasting within submarine canyons and peripheral gullies; (2) density flows within some submarine valleys; (3) sand spillover near the shelf break; (4) sediment creep on the upper slope; and (5) hemipelagic sedimentation on the middle and lower slope. The area between Georges Bank and Hudson Canyon is further distinguished by the relative abundance of large-scale slump scars and deposits on the open slope, the presence of ice-rafted debris, and the transport of sand within the heads of some submarine canyons. Between Cape Lookout and southern Florida, the slope divides into two physiographic units, and the topography is smooth and featureless. On the Florida-Hatteras Slope, offshelf sand spillover and sediment winnowing, related to Gulf Stream flow and possibly to storm-driven currents, are the major processes, whereas hemipelagic sedimentation is dominant over the offshore slope along the seaward edge of the Blake Plateau north of the Blake Spur. Slumping generally is absent south of Cape Lookout, although one large slump scarp (related to uplift over salt diapirs) has been identified east of Cape Romain. Future studies concerning sedimentary processes on the Atlantic slope need to resolve: (1) the ages and mechanisms of mass wasting; (2) the accumulation rates and thicknesses of hemipelagic sediments; and (3) the causes and variability of offshelf sand spillover, sediment winnowing, and canyon transport. 

Geologic controls on submarine slope failure along the central U.S. Atlantic margin: Insights from the Currituck Slide Complex

USGS Publications Warehouse

Hill, Jenna C.; Brothers, Daniel S.; Craig, Bradley K.; ten Brink, Uri S.; Chaytor, Jason D.; Flores, Claudia

2017-01-01

Multiple styles of failure, ranging from densely spaced, mass transport driven canyons to the large, slab-type slope failure of the Currituck Slide, characterize adjacent sections of the central U.S. Atlantic margin that appear to be defined by variations in geologic framework. Here we use regionally extensive, deep penetration multichannel seismic (MCS) profiles to reconstruct the influence of the antecedent margin physiography on sediment accumulation along the central U.S. Atlantic continental shelf-edge, slope, and uppermost rise from the Miocene to Present. These data are combined with high-resolution sparker MCS reflection profiles and multibeam bathymetry data across the Currituck Slide Complex. Pre-Neogene allostratigraphic horizons beneath the slope are generally characterized by low gradients and convex downslope profiles. This is followed by the development of thick, prograded deltaic clinoforms during the middle Miocene. Along-strike variations in morphology of a regional unconformity at the top of this middle Miocene unit appear to have set the stage for differing styles of mass transport along the margin. Areas north and south of the Currituck Slide are characterized by oblique margin morphology, defined by an angular shelf-edge and a relatively steep (> 8°), concave slope profile. Upper slope sediment bypass, closely spaced submarine canyons, and small, localized landslides confined to canyon heads and sidewalls characterize these sectors of the margin. In contrast, the Currituck region is defined by a sigmoidal geometry, with a rounded shelf-edge rollover and gentler slope gradient (< 6°). Thick (> 800 m), regionally continuous stratified slope deposits suggest the low gradient Currituck region was a primary depocenter for fluvial inputs during multiple sea level lowstands. These results imply that the rounded, gentle slope physiography developed during the middle Miocene allowed for a relatively high rate of subsequent sediment accumulation, thus providing a mechanism for compaction–induced overpressure that preconditioned the Currituck region for failure. Detailed examination of the regional geological framework illustrates the importance of both sediment supply and antecedent slope physiography in the development of large, potentially unstable depocenters along passive margins.

A hydrologically explicit, spatially exact, classification of landforms for Canada at 1:500,000 scale.

NASA Astrophysics Data System (ADS)

MacMillan, Robert A.; Geng, Xiaoyuan; Smith, Scott; Zawadzka, Joanna; Hengl, Tom

2016-04-01

A new approach for classifying landform types has been developed and applied to all of Canada using a 250 m DEM. The resulting LandMapR classification has been designed to provide a stable and consistent spatial fabric to act as initial proto-polygons to be used in updating the current 1:1 M scale Soil Landscapes of Canada map to 1:500,000 scale. There is a desire to make the current SLC polygon fabric more consistent across the country, more correctly aligned to observable hydrological and landscape features, more spatially exact, more detailed and more interpretable. The approach is essentially a modification of the Hammond (1954) criteria for classifying macro landform types as implemented for computerized analysis by Dikau (1989, 1991) and Brabyn (1998). The major modification is that the key input variables of local relief and relative position in the landscape are computed for specific hillslopes that occur between individual, explicitly defined, channels and divides. While most approaches, including Dikau et al., (1991) and SOTER (Dobos et al., 2005) compute relative relief and landscape position within a neighborhood analysis window (NAW) of some fixed size (9,600 m and 1 km respectively) the LandMapR method assesses these variables based on explicit analysis of flow paths between locally defined divides and channels (or lakes). We have modified the Hammond criteria by splitting the lowest relief class of 0-30 m into 4 classes of 0-0 m, 0-1 m, 1-10 m and 10-30 m) in order to be able to better differentiate subtle landform features in areas of low relief. Essentially this enables recognition of lakes and open water (0 relief and 0 slope), shorelines and littoral zones (0-1 m), nearly flat, low-relief landforms (1-10 m) and low relief undulating plains (10-30 m). We also modified the Hammond approach for separating upper versus lower landform positions used to differentiate flat areas in uplands from flat lowlands. We instead differentiate 3 relative slope positions of channel valley, toe slope and upper slope consistently and exhaustively and so can identify any flat areas that occur in any of these three landform positions. We did not find it necessary to use slope gradient as a criteria for defining and delineating classes because relief acts as a surrogate for slope and each relief class exhibits a narrow and definable range of slope gradients. Dominant slope gradient (or other attributes) can be computed, post classification, for each defined polygon, if there is a need to further classify by slope or other attribute. This simplifies classification and also reduces pixilation in the classification arising from considering too many local criteria in the class definitions. The resulting polygons provide an extremely detailed classification of relief and landform position at the level of individual hillslopes across all of Canada. The polygon boundaries explicitly follow major identifiable drainage networks and work their way upslope to delineate interfluves that occupy upslope positions at all levels of relief. The detailed LandMapR polygon classifications nest consistently within more general regions defined by the original Hammond-Dikau procedures. Initial visual analysis reveals a strong and consistent spatial relationship between observable changes in slope, vegetation and drainage regime and LandMapR landform polygon boundaries. More detailed quantitative assessment of the accuracy and utility of the LandMapR polygon classes is planned.

Slope angle estimation method based on sparse subspace clustering for probe safe landing

NASA Astrophysics Data System (ADS)

Li, Haibo; Cao, Yunfeng; Ding, Meng; Zhuang, Likui

2018-06-01

To avoid planetary probes landing on steep slopes where they may slip or tip over, a new method of slope angle estimation based on sparse subspace clustering is proposed to improve accuracy. First, a coordinate system is defined and established to describe the measured data of light detection and ranging (LIDAR). Second, this data is processed and expressed with a sparse representation. Third, on this basis, the data is made to cluster to determine which subspace it belongs to. Fourth, eliminating outliers in subspace, the correct data points are used for the fitting planes. Finally, the vectors normal to the planes are obtained using the plane model, and the angle between the normal vectors is obtained through calculation. Based on the geometric relationship, this angle is equal in value to the slope angle. The proposed method was tested in a series of experiments. The experimental results show that this method can effectively estimate the slope angle, can overcome the influence of noise and obtain an exact slope angle. Compared with other methods, this method can minimize the measuring errors and further improve the estimation accuracy of the slope angle.

Hydrogeomorphic Classification of Wetlands on Mt. Desert Island, Maine, Including Hydrologic Susceptibility Factors for Wetlands in Acadia National Park

USGS Publications Warehouse

Nielsen, Martha G.

2006-01-01

The U.S. Geological Survey, in cooperation with the National Park Service, developed a hydrogeomorphic (HGM) classification system for wetlands greater than 0.4 hectares (ha) on Mt. Desert Island, Maine, and applied this classification using map-scale data to more than 1,200 mapped wetland units on the island. In addition, two hydrologic susceptibility factors were defined for a subset of these wetlands, using 11 variables derived from landscape-scale characteristics of the catchment areas of these wetlands. The hydrologic susceptibility factors, one related to the potential hydrologic pathways for contaminants and the other to the susceptibility of wetlands to disruptions in water supply from projected future changes in climate, were used to indicate which wetlands (greater than 1 ha) in Acadia National Park (ANP) may warrant further investigation or monitoring. The HGM classification system consists of 13 categories: Riverine-Upper Perennial, Riverine-Nonperennial, Riverine- Tidal, Depressional-Closed, Depressional-Semiclosed, Depressional-Open, Depressional-No Ground-Water Input, Mineral Soil Flat, Organic Soil Flat, Tidal Fringe, Lacustrine Fringe, Slope, and Hilltop/Upper Hillslope. A dichotomous key was developed to aid in the classification of wetlands. The National Wetland Inventory maps produced by the U.S. Fish and Wildlife Service provided the wetland mapping units used for this classification. On the basis of topographic map information and geographic information system (GIS) layers at a scale of 1:24,000 or larger, 1,202 wetland units were assigned a preliminary HGM classification. Two of the 13 HGM classes (Riverine-Tidal and Depressional-No Ground-Water Input) were not assigned to any wetlands because criteria for determining those classes are not available at that map scale, and must be determined by more site-specific information. Of the 1,202 wetland polygons classified, which cover 1,830 ha in ANP, 327 were classified as Slope, 258 were Depressional (Open, Semiclosed, and Closed), 231 were Riverine (Upper Perennial and Nonperennial), 210 were Soil Flat (Mineral and Organic), 68 were Lacustrine Fringe, 51 were Tidal Fringe, 22 were Hilltop/Upper Hillslope, and another 35 were small open water bodies. Most small, isolated wetlands classified on the island are Slope wetlands. The least common, Hilltop/Upper Hillslope wetlands, only occur on a few hilltops and shoulders of hills and mountains. Large wetland complexes generally consist of groups of Depressional wetlands and Mineral Soil Flat or Organic Soil Flat wetlands, often with fringing Slope wetlands at their edges and Riverine wetlands near streams flowing through them. The two analyses of wetland hydrologic susceptibility on Mt. Desert Island were applied to 186 wetlands located partially or entirely within ANP. These analyses were conducted using individually mapped catchments for each wetland. The 186 wetlands were aggregated from the original 1,202 mapped wetland polygons on the basis of their HGM classes. Landscape-level hydrologic, geomorphic, and soil variables were defined for the catchments of the wetlands, and transformed into scaled scores from 0 to 10 for each variable. The variables included area of the wetland, area of the catchment, area of the wetland divided by the area of the catchment, the average topographic slope of the catchment, the amount of the catchment where bedrock crops out with no soil cover or excessively thin soil cover, the amount of storage (in lakes and wetlands) in the catchment, the topographic relief of the catchment, the amount of clay-rich soil in the catchment, the amount of manmade impervious surface, whether the wetland had a stream inflow, and whether the wetland had a hydraulic connection to a lake or estuary. These data were determined using a GIS and data layers mapped at a scale of 1:24,000 or larger. These landscape variables were combined in different ways for the two hydrologic susceptibility fact

Comparison of morphology of active cyclic steps created by turbidity currents on Squamish Delta, British Columbia, Canada with flume experiments

NASA Astrophysics Data System (ADS)

Yokokawa, Miwa; Yamamoto, Shinya; Higuchi, Hiroyuki; Hughes Clarke, John E.; Izumi, Norihiro

2015-04-01

Upper-flow-regime bedforms, such as cyclic steps and antidunes, have been reported to be formed by turbidity currents. Their formative conditions are, however, not fully understood because of the difficulty of field surveys in the deep sea. Field observations of turbidity currents and seabed topography on the Squamish delta in Howe Sound, British Columbia, Canada have been undertaken which found bedwaves actively migrating in the upstream direction in channels formed on the prodelta slope. Their topography and behavior suggest that they are cyclic steps formed by turbidity currents. Because Squamish delta is as shallow as around 150 m, and easy to access compared with general submarine canyons, it is thought to be one of the best places for studying characteristics of cyclic steps formed by turbidity currents through field observations. In this study, we have analyzed configurations of cyclic steps with the use of data obtained in the field observation of 2011, and compare them with the data from the flume experiments. On the prodelta slope, three major active channels are clearly developed. In addition to the sonar survey, a 600 kHz ADCP was installed in 150m of water just seaward of the termination of the North Channel. In addition, 1200kHz ADCP and 500kHz M3s are suspended from the research vessel in 60 m of water and 300 m distance from the delta edge. We selected images showing large daily differences. The steps move vigorously at the upper 600m parts of the prodelta slope, so that we measured the steps in this area. From the profiles perpendicular to the bedwave crest lines through the center of channels, wavelength and wave height for each step, mean slope were measured on the software for quantitative image analyses manually. Wave steepness for each step was calculated using the wavelength and wave height measured as above. The mean slope ranges from 6.8° ~ 2.7° (more proximal, steeper), mean wavelength and wave heights of steps range from 24.5 to 87.6m and from 2.4 to 5.4m respectively. We compare the shape of steps with the upper-flow-regime bedforms, such as antidunes and cyclic steps, obtained from the open channel experiments. Wave steepness of the steps in Squamish ranges from 0.035 to 0.157, which is relatively high and close in value to those of cyclic steps and downstream-migrating-antidunes (DMA) in the open channel experiments. The non-dimensional wave number depends on the estimation of the thickness of the turbidity currents. Based on the optical backscatter profiles, the upper limit of sediment suspension is around 10m. However the maximum velocity is always located within the lower 5m, and higher density layer seems to locate within the lowermost 2 m. For the 10m flow thickness, the wave number is close in value to those of DMA. While for the 0.5m flow thickness, the wave number is close in value to those of cyclic steps. We will discuss about the effect of "density currents" and/or "surge" on the morphology of those steps.

Seismic evidence for Messinian salt deformation and fluid circulation on the South Balearic margin (Western Mediterranean)

NASA Astrophysics Data System (ADS)

Wardell, Nigel; Camerlenghi, Angelo; Urgeles, Roger; Geletti, Riccardo; Tinivella, Umberta; Giustiniani, Michela; Accettella, Daniela

2014-05-01

The south Balearic margin is characterized by an abrupt tectonically-controlled transition between a steep continental slope (Emile Baudot escarpment) and the Algero-Balearic abyssal plain, in which Messinain salt-induced deformation affects the seafloor morphology. Multichannel seismic profiles, multibeam bathymetry, and shallow seismic data demonstrate that the extent of salt deformation does not coincide with the bathymetric plain-slope transition. Instead, deformation occurs south of linear structure in the abyssal plain located some tens of kilometres from the base of the slope. The quality of the multi-channel seismic record in the deep water deformed area is severely decreased by the three dimensional character of the salt structures. However, the abyssal plain near the base of the slope reveals details on the Messinian sequence, its structure, post-Messinan deformation, and relation with subsurface fluids. The analysis of part of the EUROFLEETS SALTFLU multichannel seismic data set has included detailed RMS velocity analysis, post-stack and pre-stack time migration. An anomalously thick (up to 800 ms twt) acoustically laminated unit comprising the Messinian Upper Unit (UU) is present near the base of the slope and is characterized by syn-sedimentary gentle symmetric folding. The crests of such folds are affected by small-offset, layer-bound fractures and faults propagating from the upper part to the UU to the Plio-Quaternary sequence. Amplitude anomalies, polarity inversion and at times acoustic blanking reveal the presence of fluids (presumably gas) within the Messinian sequence. A clear seismic evidence for the Mobile Unit (MU, or salt layer) is missing in this area. Seismic evidence for the MU exists south of the linear structural boundary, where salt induced deformation has created vertical displacements of several hundreds of metres, diapiric growth, and at least two salt/mud piercement structures at the seafloor. In the highly deformed area, the UU and the Lower Unit (LU) appear to amalgamate as a consequence of complete salt withdrawal around diapirs. The seismic analysis is focussed on determining whether the boundary between low and high degree of deformation in the abyssal plain is determined by the limit of the salt distribution. In this case the northern limit of the Messinian pure salt basin would not coincide with the present day continental slope, thus requiring either a strong control of Messinian tectonic structures an salt deposition and/or a contamination of salt with clastics.

Slope failures and timing of turbidity flows north of Puerto Rico

USGS Publications Warehouse

ten Brink, Uri S.; Chaytor, Jason D.

2014-01-01

The submerged carbonate platform north of Puerto Rico terminates in a high (3,000–4,000 m) and in places steep (>45°) slope characterized by numerous landslide scarps including two 30–50 km-wide amphitheater-shaped features. The origin of the steep platform edge and the amphitheaters has been attributed to: (1) catastrophic failure, or (2) localized failures and progressive erosion. Determining which of the two mechanisms has shaped the platform edge is critically important in understanding landslide-generated tsunami hazards in the region. Multibeam bathymetry, seismic reflection profiles, and a suite sediment cores from the Puerto Rico Trench and the slope between the trench and the platform edge were used to test these two hypotheses. Deposits within trench axis and at the base of the slope are predominantly composed of sandy carbonate turbidites and pelagic sediment with inter-fingering of chaotic debris units. Regionally-correlated turbidites within the upper 10 m of the trench sediments were dated between ∼25 and 22 kyrs and ∼18–19 kyrs for the penultimate and most recent events, respectively. Deposits on the slope are laterally discontinuous and vary from thin layers of fragmented carbonate platform material to thick pelagic layers. Large debris blocks or lobes are absent within the near-surface deposits at the trench axis and the base of slope basins. Progressive small-scale scalloping and self-erosion of the carbonate platform and underlying stratigraphy appears to be the most likely mechanism for recent development of the amphitheaters. These smaller scale failures may lead to the generation of tsunamis with local, rather than regional, impact.

Unusual megafaunal assemblages on the continental slope off Cape Hatteras

NASA Astrophysics Data System (ADS)

Hecker, Barbara

Megafaunal assemblages were studied in August-September 1992 using a towed camera sled along seven cross-isobath transects on the continental slope off Cape Hatteras. A total of 20,722 megafaunal organisms were observed on 10,918 m 2 of the sea floor between the depths of 157 and 1 924 m. These data were compared with data previously collected off Cape Hatteras in 1985 and at other locations along the eastern U.S. coast between 1981 and 1987. Megafaunal populations on the upper and lower slopes off Cape Hatteras were fouond to be similar, in terms of density and species composition, to those observed at the other locations. In contrast, megafaunal abundances were found to be elevated (0.88 and 2.65 individuals per m 2 during 1985 and 1992, respectively) on the middle slope off Cape Hatteras when compared to most other slope locations (<0.5individuals per m 2). These elevated abundances mainly reflect dense populations of three demersal fish, two eel pouts ( Lysenchelys verrilli and Lycodes atlanticus) and the witch flounder Glyptocephalus cynoglossus, and a large anemone ( Actinauge verrilli). These four species dominated the megafauna off Cape Hatteras, whereas they represented only a minor component of megafaunal populations found at other slope locations. Additionally, numerous tubes of the foraminiferan Bathysiphon filiformis were observed off Cape Hatteras, but not elsewhere. The high density of demersal fish found off Cape Hatteras appears to be related to the high densities of infaunal prey reported from this area. The high densities of A. verrilli and B. fuliformis may be related to the same factors responsible for the high infaunal densities, namely enhanced nutrient inputs in the form of fine particles. Extreme patchiness also was observed in the distributions of the middle slope taxa off Cape Hatteras. This patchiness may reflect the habitat heterogeneity of this exceptionally rugged slope and the sedentary nature of the organisms inhabiting it.

Geologic map of the Granite 7.5' quadrangle, Lake and Chaffee Counties, Colorado

USGS Publications Warehouse

Shroba, Ralph R.; Kellogg, Karl S.; Brandt, Theodore R.

2014-01-01

The geologic map of the Granite 7.5' quadrangle, Lake and Chaffee Counties, Colorado, portrays the geology in the upper Arkansas valley and along the lower flanks of the Sawatch Range and Mosquito Range near the town of Granite. The oldest rocks, exposed in the southern and eastern parts of the quadrangle, include gneiss and plutonic rocks of Paleoproterozoic age. These rocks are intruded by younger plutonic rocks of Mesoproterozoic age. Felsic hypabyssal dikes, plugs, and plutons, ranging in age from Late Cretaceous or Paleocene to late Oligocene, locally intruded Proterozoic rocks. A small andesite lava flow of upper Oligocene age overlies Paleoproterozoic rock, just south of the Twin Lakes Reservoir. Gravelly fluvial and fan deposits of the Miocene and lower Pliocene(?) Dry Union Formation are preserved in the post-30 Ma upper Arkansas valley graben, a northern extension of the Rio Grande rift. Mostly north-northwest-trending faults displace deposits of the Dry Union Formation and older rock units. Light detection and ranging (lidar) imagery suggests that two short faults, near the Arkansas River, may displace surficial deposits as young as middle Pleistocene. Surficial deposits of middle Pleistocene to Holocene age are widespread in the Granite quadrangle, particularly in the major valleys and on slopes underlain by the Dry Union Formation. The main deposits are glacial outwash and post-glacial alluvium; mass-movement deposits transported by creep, debris flow, landsliding, and rockfall; till deposited during the Pinedale, Bull Lake, and pre-Bull Lake glaciations; rock-glacier deposits; and placer-tailings deposits formed by hydraulic mining and other mining methods used to concentrate native gold. Hydrologic and geologic processes locally affect use of the land and locally may be of concern regarding the stability of buildings and infrastructure, chiefly in low-lying areas along and near stream channels and locally in areas of moderate to steep slopes. Low-lying areas along major and minor streams are subject to periodic stream flooding. Mass-movement deposits and deposits of the Dry Union Formation that underlie moderate to steep slopes are locally subject to creep, debris-flow deposition, and landsliding. Proterozoic rocks that underlie steep slopes are locally subject to rockfall. Sand and gravel resources for construction and other uses in and near the Granite quadrangle are present in outwash-terrace deposits of middle and late Pleistocene age along the Arkansas River and along tributary streams in glaciated valleys.

Controls on alluvial fans morphology

NASA Astrophysics Data System (ADS)

Delorme, P.; Devauchelle, O.; Lajeunesse, E.; Barrier, L.; Métivier, F.

2017-12-01

Using laboratory experiments, we investigate the influence of water and sediment discharges on the morphology of an alluvial fan. In our flume, a single-thread laminar river deposits corundum sand (0.4 mm) into a conical fan. We record the fan progradation with top-view images, and measure its shape using the deformation of a Moiré pattern. The fan remains virtually self-affine as it grows, with a nearly constant slope. We find that, when the sediment discharge is small, the longitudinal slope of the fan remains close to that of a river at the threshold for sediment transport. A higher sediment discharge causes the fan's slope to depart from the threshold value. Due to the downstream decrease of the sediment load, this slope gets shallower towards the fan's toe. This mechanism generates a slightly concave fan profile. This suggests that the proximal slope of an alluvial fan could be a proxy for the sediment flux that feeds the fan.Finally, we discuss the applicability of these results to natural systems.

Internal tides affect benthic community structure in an energetic submarine canyon off SW Taiwan

NASA Astrophysics Data System (ADS)

Liao, Jian-Xiang; Chen, Guan-Ming; Chiou, Ming-Da; Jan, Sen; Wei, Chih-Lin

2017-07-01

Submarine canyons are major conduits of terrestrial and shelf organic matter, potentially benefiting the seafloor communities in the food-deprived deep sea; however, strong bottom currents driven by internal tides and the potentially frequent turbidity currents triggered by storm surges, river flooding, and earthquakes may negatively impact the benthos. In this study, we investigated the upper Gaoping Submarine Canyon (GPSC), a high-sediment-yield canyon connected to a small mountain river (SMR) off southwest (SW) Taiwan. By contrasting the benthic meiofaunal and macrofaunal communities within and outside the GPSC, we examined how food supplies and disturbance influenced the benthic community assemblages. The benthic communities in the upper GPSC were mainly a nested subset of the adjacent slope assemblages. Several meiofaunal (e.g. ostracods) and macrofaunal taxa (e.g. peracarid crustaceans and mollusks) that typically occurred on the slope were lost from the canyon. The polychaete families switched from diverse feeding guilds on the slope to motile subsurface deposit feeders dominant in the canyon. The diminishing of epibenthic peracarids and proliferation of deep burrowing polychaetes in the GPSC resulted in macrofauna occurring largely within deeper sediment horizons in the canyon than on the slope. The densities and numbers of taxa were depressed with distinct and more variable composition in the canyon than on the adjacent slope. Both the densities and numbers of taxa were negatively influenced by internal tide flushing and positively influenced by food availability; however, the internal tides also negatively influenced the food supplies. While the meiofauna and macrofauna densities were both depressed by the extreme physical conditions in the GPSC, only the macrofaunal densities increased with depth in the canyon, presumably related to increased frequency and intensity of disturbance toward the canyon head. The population densities of meiofauna, on the other hand, rebounded more rapidly due to their fast growth rate and short generation time and thus did not display bathymetric pattern in the canyon. To our knowledge, this is the first benthic ecological study in a submarine canyon connected to a high-sediment-yield SMR. The biological responses to extreme physical conditions in the GPSC could have broad implications on understanding the anthropogenic and climate change impacts in the deep-sea ecosystems.

The influence of badland surfaces and erosion processes on vegetation cover

NASA Astrophysics Data System (ADS)

Hardenbicker, Ulrike; Matheis, Sarah

2014-05-01

To assess the links between badland geomorphology and vegetation cover, we used detailed mapping in the Avonlea badlands, 60 km southwest of Regina, Saskatchewan Canada. Three badlands surfaces are typical in the study area: a basal pediment surface, a mid-slope of bentonitic mudstone with typical popcorn surface, and an upper slope with mud-cemented sandstone. Badland development was triggered by rapid post Pleistocene incision of a meltwater channel in Upper Cretaceous marine and lagoonal sediments. After surveying and mapping of a test area, sediment samples were taken to analyze geophysical parameters. A detailed geomorphic map and vegetation map (1:1000) were compared and analyzed in order to determine the geomorphic environment for plant colonization. The shrink-swell capacity of the bentonitic bedrock, slaking potential and dispersivity are controlled by soil texture, clay mineralogy and chemistry, strongly influencing the timing and location of runoff and the relative significance of surface and subsurface erosional processes. The absence of shrink-swell cracking of the alluvial surfaces of the pediments indicates a low infiltration capacity and sheetflow. The compact lithology of the sandstone is responsible for its low permeability and high runoff coefficient. Slope drainage of steep sandstone slopes is routed through a deep corrasional pipe network. Silver sagebrush (Artemisia cana) is the only species growing on the popcorn surface of the mudrock, which is in large parts vegetation free. The basal pediment shows a distinct 2 m band surrounding the mudrock outcrop without vegetation as a result of high sedimentation rate due to slope wash. Otherwise the typical pioneer vegetation of this basal pediment are grasses. In the transition zone below the steep sandstone cliffs and above the gentle bentonitic mudrock surfaces patches of short-grass vegetation are found, marking slumped blocks with intact vegetation and soil cover. These patches are surrounded by less dense pioneer vegetation consisting of grasses and sage bushes indicating minimal surface erosion or sedimentation. Geomorphic mapping documented a high density of active pipes in this area, transporting silt and fine sand from the sandstone cliffs to lower and basal pediments. Vegetation cover alone is a poor indicator of badland surfaces and erosion processes because of the three-dimensional nature of badland erosion processes, and the shrink-swell capacity of the bentonitic bedrock. A combination of geomorphic and vegetation mapping is needed to identify badland surfaces and processes in the study area.

47 CFR 73.757 - System specifications for single-sideband (SSB) modulated emissions in the HF broadcasting service.

Code of Federal Regulations, 2013 CFR

2013-10-01

... emission is one giving the same audio-frequency signal-to-noise ratio at the receiver output as the... is equally valid for both DSB and SSB emissions. (3) Audio-frequency band. The upper limit of the audio-frequency band (at—3 dB) of the transmitter shall not exceed 4.5 kHz with a further slope of...

47 CFR 73.757 - System specifications for single-sideband (SSB) modulated emissions in the HF broadcasting service.

Code of Federal Regulations, 2014 CFR

2014-10-01

... emission is one giving the same audio-frequency signal-to-noise ratio at the receiver output as the... is equally valid for both DSB and SSB emissions. (3) Audio-frequency band. The upper limit of the audio-frequency band (at—3 dB) of the transmitter shall not exceed 4.5 kHz with a further slope of...

47 CFR 73.757 - System specifications for single-sideband (SSB) modulated emissions in the HF broadcasting service.

Code of Federal Regulations, 2012 CFR

2012-10-01

... emission is one giving the same audio-frequency signal-to-noise ratio at the receiver output as the... is equally valid for both DSB and SSB emissions. (3) Audio-frequency band. The upper limit of the audio-frequency band (at—3 dB) of the transmitter shall not exceed 4.5 kHz with a further slope of...

Height-age and site index curves for Pacific silver fir in the Pacific Northwest.

Treesearch

Gerald E. Hoyer; Francis R. Herman

1989-01-01

Forty felled dominant and codominant Pacific silver fir trees (Abies amabilis Dougl. ex Forbes) from 39 locations provided the basis for height-age and site index curves. Trees were from upper slope forests of the Cascade Range in Oregon and Washington. Trees ranged in age from 100 to 300 years and were identified by their height-growth trend as...

Effects of timber harvest on elk distribution in the Blue Mountains of Oregon.

Treesearch

Jon M. Skovlin; Larry D. Bryant; Paul J. Edgerton

1989-01-01

A long-term study to determine the effects of several methods of timber harvest on the distribution of Rocky Mountain elk (Cervus elaphus nelsoni) was begun in the early 1970's in the Blue Mountains of northeastern Oregon. The study area was an upper slope spruce-fir type with harvest designed to compare changes in elk use, as measured by...

The Study of Upper Ocean Stratification that Controls Propagation of Internal Tidal Bores in Coastal Areas

DTIC Science & Technology

2012-06-01

turbulence . McPhee-Shaw determined that intrusions typically formed in regions where the incident and reflected wave beams overlap on the slope...Figure 7. Optical backscatter data from the Spray glider. The saturation point for the optical backscatter is 4.096 V. The green and red profiles...plot is a cross shelf section of optical backscatter . ..........................................................................25 Figure 9

Frost on Dunes

NASA Technical Reports Server (NTRS)

2005-01-01

18 March 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows dark dunes on a crater floor during the southern spring. Some of the dunes have frost on their south-facing slopes.

Location near: 52.3oS, 326.7oW Image width: 3 km (1.9 mi) Illumination from: upper left Season: Southern Spring

Mud volcano venting induced gas hydrate formation at the upper slope accretionary wedge, offshore SW Taiwan

NASA Astrophysics Data System (ADS)

Lin, Saulwood; Tseng, Yi-Ting; Cheng, Wan-Yen; Chou, Cheng-Tien; Chen, NeiChen; Hsieh, I.-Chih

2016-04-01

TsanYao Mud Volcano (TYMV) is the largest mud volcano cone in the Hengchun Mud Volcano Group (HCMVG), located at the upper slope of the accrretionary wedge, southwest of Taiwan. The region is under active tectonic activity with the Philippine Plate, moving northwestward at a rate of ~8 cm/year. This region also receives huge quantity of suspended particle load of ~100 mT/year at present time from adjacent small rivers of the Island of Taiwan. Large loads of suspended sediments influx become a major source of organic carbon and later gas and other hydrocarbon. Gas and fluid in the mud volcano are actively venting from deep to the sea floor on the upper slope of the accretionary wedge. In order to understand venting on the HCMVG, echo sounder, towcam and coring were carried out. Pore water sulfate, chloride, potassium, calcium, stable isotope O-18, gas compositions, dissolved sulfide were analysed. The HCMVG consists of 12 volcano cones of different sizes. Large quantity of gas and fluid are venting directly from deep to the TYMV structure high, as well as 50+ other vents as appeared as flares on the echo sounder. Some flares are reaching to the atmosphere and likely a source of green house gases to the atmosphere. Venting fluids include gas bubbles, suspended particle, mud, and breccia. Breccia size could reach more than 12 cm in diameter. Circular bands in different color appeared around the cone may represent stages of vent eruptions. Compositions of vent gas include methane, ethane and propane. High proportions of ethane and propane in the vent gas demonstrated that source of gas are thermogenic in origin. Patchy authigenic carbonate, bacterial mats, bivalves, tube worms and other chemosynthesis organisms were supported by venting gas AOM process near the sea floor. Pore water chloride concentrations show distinct variation pattern from center cone to the side of the volcano, with low in the center and high away from the cone. Pore water with higher than seawater chloride indicated gas hydrate formation in sediments away from the mud volcano cone.

Soil properties in high-elevation ski slopes

NASA Astrophysics Data System (ADS)

Filippa, Gianluca; Freppaz, Michele; Letey, Stéphanie; Corti, Giuseppe; Cocco, Stefania; Zanini, Ermanno

2010-05-01

The development of winter sports determines an increasing impact on the high altitude ecosystems, as a consequence of increased participation and an increasing demand of high quality standards for skiable areas. The construction of a ski slope is associated with a certain impact on soil, which varies as a function of the degree of human-induced disturbance to the native substrata. In this work, we provide a description of the characteristics of alpine tundra ski-slope soils and their nutrient status, contrasted with undisturbed areas. The study site is located in the Monterosaski Resort, Aosta Valley, NW Italy (45°51' N; 7°48' E). We chose 5 sites along an altitudinal gradient between 2700 and 2200 m a.s.l.. Per each site, one plot was established on the ski slope, while a control plot was chosen under comparable topographic conditions a few meters apart. Soils were described and samples were collected and analysed for main chemical-physical properties. In addition an evaluation of N forms, organic matter fractionation and microbial biomass was carried out. Soil depth ranged between 10 to more than 70 cm, both on the ski slope and in the undisturbed areas. A true organo-mineral (A) horizon was firstly identified at 2500 m a.s.l., while a weathering horizon (Bw) was detected at 2400 m a.s.l.. However, a Bw horizon thick enough to be recognised as diagnostic for shifting soil classification order from Entisols to Inceptisols (USDA-Soil Taxonomy) was detected only below 2400 m a.s.l.. Lithic Cryorthents were predominant in the upper part of the sequence (above 2500 m a.s.l.), both in the ski slope and the undisturbed areas; Typic Cryorthents were identified between 2500 and 2400 m a.s.l., while Inceptisols were predominant between 2400 and 2200 m a.s.l.. Chemical-physical properties will be discussed focusing on the main differences between ski slope and undisturbed soils, as determined by the ski slope construction. Pedogenetic processes at high altitude are strongly limited by extreme climatic conditions, resulting in low resistance and resilience with respect to any human-induced changes; therefore, it is key to quantify the impact of ski slope construction and management on such fragile pedo-ecosystems. KEYWORDS: alpine tundra, pedogenesis, ski slope construction, ski slope management

Statistical methods for astronomical data with upper limits. II - Correlation and regression

NASA Technical Reports Server (NTRS)

Isobe, T.; Feigelson, E. D.; Nelson, P. I.

1986-01-01

Statistical methods for calculating correlations and regressions in bivariate censored data where the dependent variable can have upper or lower limits are presented. Cox's regression and the generalization of Kendall's rank correlation coefficient provide significant levels of correlations, and the EM algorithm, under the assumption of normally distributed errors, and its nonparametric analog using the Kaplan-Meier estimator, give estimates for the slope of a regression line. Monte Carlo simulations demonstrate that survival analysis is reliable in determining correlations between luminosities at different bands. Survival analysis is applied to CO emission in infrared galaxies, X-ray emission in radio galaxies, H-alpha emission in cooling cluster cores, and radio emission in Seyfert galaxies.

Facies analysis and depositional environments of upper part of Richmond group (upper Ordovician), Richmond, Indiana, to Xenia, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Betz, C.E.; Martin, W.D.

Rock sections of the Drakes, Elkhorn, and Whitewater Formations were studied along an east-west-trending line in order to distinguish facies changes in a slope direction across the paleodepositional basin. The Richmond limestones, shales, and dolostones formed from fine-grained, terrigenous and carbonate sediments deposited on a shallow marine ramp within the humid, tropical, low latitudes of the Southern Hemisphere. Depositional environments on the ramp are represented by five main facies type. The five Richmond facies form a subtidal to supratidal shallowing-upward sequence. This progressive shallowing during the Late Ordovician resulted from the westward regional progradation of Queenston deltaic facies.

Intersection

NASA Technical Reports Server (NTRS)

2006-01-01

9 June 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a small portion of a dust-covered plain directly north of Labyrinthus Noctis which is cut by three linear troughs. The two long troughs running diagonally from the lower left (southwest) to the upper right (northeast) are connected by a third, shorter trough. Boulders derived from erosion of layered rock in the trough walls are seen perched on the sloping sidewalls and resting on the trough floors among giant windblown ripples.

Location near: 0.2oN, 105.0oW Image width: 3 km (1.9 mi) Illumination from: upper left Season: Northern Spring

Seismicity in the platform regions of Ukraine in the zones of anomalous electrical conductivity

NASA Astrophysics Data System (ADS)

Kushnir, A. N.; Kulik, S. N.; Burakhovich, T. K.

2013-05-01

It is established for the first time that there are several regions in Ukraine, in which the earthquakes occurring within platform territory are correlated to the anomalous conductive structures in the Earth's crust and upper mantle. These regions are identified as (1) Donbass and the eastern part of the Dnieper-Donetsk Depression (DDD); (2) eastern margin of the Ingulets-Krivoi Rog suture zone in the area of the Krivoi Rog-Kremenchug fault zone; (3) the western part of the Cis-Azov megablock; (4) the western boundary of the Ukrainian Shield and its slope; (5) North Dobruja and Pre-Dobrujan Depression. The reconstructed tree-dimensional (3D) geoelectrical models of the Earth's crust and upper mantle feature anomalously low values of electric resistivity. The earthquake sources in the platform areas of Ukraine are localized above the top and in the upper parts of the crustal anomalies of electrical conductivity.

Management guidelines for enhancing Cerulean Warbler breeding habitat in Appalachian hardwood forests

USGS Publications Warehouse

Wood, Petra; Sheehan, James; Keyser, Patrick D.; Buehler, David A.; Larkin, Jeff; Rodewald, Amanda D.; Stoleson, Scott H.; Wigley, T. Bently; Mizel, Jeremy; Boves, Than J.; George, Greg; Bakermans, Marja H.; Beachy, Tiffany A.; Evans, Andrea; McDermott, Molly E.; Newell, Felicity L.; Perkins, Kelly A.; White, Matt

2013-01-01

The Cerulean Warbler (Setophaga cerulea) is a migratory songbird that breeds in mature deciduous forests of eastern North America. Cerulean Warblers (hereafter, ceruleans) require heavily forested landscapes for nesting and, within Appalachian forests, primarily occur on ridge tops and steep, upper slopes. They are generally associated with oakdominated (Quercus spp.) stands that contain gaps in the forest canopy, that have large diameter trees (>16 inches diameter breast height (dbh)), and that have well-developed understory-and upper-canopy layers. Ceruleans primarily use the midand upper-canopy where they glean insects from the surface of leaves and conceal their open cup nests. Because they are severely declining across much of their range (Fig. 1), habitat management is a high priority. Management for this species can also improve conditions for a number of other wildlife species that depend on the same structure.

Morphologic contrasts between Nirgal and Auqakuh Valles, Mars: Evidence of different crustal properties

NASA Technical Reports Server (NTRS)

Mackinnon, David J.; Tanaka, Kenneth L.; Winchell, Philip J.

1987-01-01

Photoclinometric measurements were made of sidewall slopes in Nirgal and Auqakuh Valles and these results were interpreted in terms of the geologic setting and a simple geomorphic model to provide insights into the physical properties of crustal materials in these areas. Nirgal was interpreted to be a runoff channel and Auqakuh to be a fretted channel. Geomorphologic arguments for the sapping origin of Nirgal and Auqakuh Valles were presented. The morphologies of the channels, however, differ greatly: the tributaries of Nirgal end abruptly in theater-headed canyons, whereas the heads of tributaries of Auqakuh shallow gradually. The plateau surface surrounding both channels appears to be covered by smooth materials, presumably lava flows; they are continuous and uneroded in the Nirgal area, but at Auqakuh they are largely eroded and several layers are exposed that total about 200 m in thickness. For Nirgal Valles, the measurements show that sidewalls in the ralatively shallow upper reaches of the channel have average slopes near 30 degrees and, in the lower reaches, sidewall slopes exceed 50 degrees. Auqakuh, on the other hand, has maximum sidewall slopes of 14 degrees and an approximate maximum depth of 1000 m. Faint, horizontal layering in portions of the lower reaches of Nirgal may indicate inhomogeneity in either composition or topography.

Transient Slope Lineae Formation in a Well-Preserved Crater

NASA Image and Video Library

2017-11-20

This enhanced color image from NASA's Mars Reconnaissance Orbiter (MRO) shows what are called "recurring slope lineae"s in Tivat Crater. The narrow, dark flows descend downhill (towards the upper left). Analysis shows that the flows all end at approximately the same slope, which is similar to the angle of repose for sand. RSL are mostly found on steep rocky slopes in dark regions of Mars, such as the southern mid-latitudes, Valles Marineris near the equator, and in Acidalia Planitia on the northern plains. The appearance and growth of these features resemble seeping liquid water, but how they form remains unclear, and this research demonstrated that the RSL flows seen by HiRISE are likely moving granular material like sand and dust. These findings indicate that present-day Mars may not have a significant volume of liquid water. The water-restricted conditions that exist on Mars would make it difficult for Earth-like life to exist near the surface of the planet. The map is projected here at a scale of 25 centimeters (9.8 inches) per pixel. [The original image scale is 25.6 centimeters (10.8 inches) per pixel (with 1 x 1 binning); objects on the order of 77 centimeters (30.3 inches) across are resolved.] North is up. https://photojournal.jpl.nasa.gov/catalog/PIA22114

Normal faulting of the Daiichi-Kashima Seamount in the Japan Trench revealed by the Kaiko I cruise, Leg 3

USGS Publications Warehouse

Kobayashi, K.; Cadet, J.-P.; Aubouin, J.; Boulegue, J.; Dubois, J.; von Huene, Roland E.; Jolivet, L.; Kanazawa, T.; Kasahara, J.; Koizumi, K.-i.; Lallemand, S.; Nakamura, Y.; Pautot, G.; Suyehiro, K.; Tani, S.; Tokuyama, H.; Yamazaki, T.

1987-01-01

A detailed topographic and geophysical survey of the Daiichi-Kashima Seamount area in the southern Japan Trench, northwestern Pacific margin, clearly defines a high-angle normal fault which splits the seamount into two halves. A fan-shaped zone was investigated along 2-4 km spaced, 100 km long subparallel tracks using narrow multi-beam (Seabeam) echo-sounder with simultaneous measurements of gravity, magnetic total field and single-channel seismic reflection records. Vertical displacement of the inboard half was clearly mapped and its normal fault origin was supported. The northern and southern extensions of the normal fault beyond the flank of the seamount were delineated. Materials on the landward trench slope are displaced upward and to sideways away from the colliding seamount. Canyons observed in the upper landward slope terminate at the mid-slope terrace which has been uplifted since start of subduction of the seamount. Most of the landward slope except for the landward walls aside the seamount comprises only a landslide topography in a manner similar to the northern Japan Trench wall. This survey was conducted on R/V "Jean Charcot" as a part of the Kaiko I cruise, Leg 3, in July-August 1984 under the auspices of the French-Japanese scientific cooperative program. ?? 1987.

Geomorphic control of landscape carbon accumulation

USGS Publications Warehouse

Rosenbloom, N.A.; Harden, J.W.; Neff, J.C.; Schimel, D.S.

2006-01-01

We use the CREEP process-response model to simulate soil organic carbon accumulation in an undisturbed prairie site in Iowa. Our primary objectives are to identify spatial patterns of carbon accumulation, and explore the effect of erosion on basin-scale C accumulation. Our results point to two general findings. First, redistribution of soil carbon by erosion results in a net increase in basin-wide carbon storage relative to a noneroding environment. Landscape-average mean residence times are increased in an eroding landscape owing to the burial/preservation of otherwise labile C. Second, field observations taken along a slope transect may overlook significant intraslope variations in carbon accumulation. Spatial patterns of modeled deep C accumulation are complex. While surface carbon with its relatively short equilibration time is predictable from surface properties, deep carbon is strongly influenced by the landscape's geomorphic and climatic history, resulting in wide spatial variability. Convergence and divergence associated with upland swales and interfluves result in bimodal carbon distributions in upper and mid slopes; variability in carbon storage within modeled mid slopes was as high as simulated differences between erosional shoulders and depositional valley bottoms. The bimodality of mid-slope C variability in the model suggests that a three-dimensional sampling strategy is preferable over the traditional two-dimensional analog or "catena" approach. Copyright 2006 by the American Geophysical Union.

Adriatic storm surges and related cross-basin sea-level slope

NASA Astrophysics Data System (ADS)

Međugorac, Iva; Orlić, Mirko; Janeković, Ivica; Pasarić, Zoran; Pasarić, Miroslava

2018-05-01

Storm surges pose a severe threat to the northernmost cities of the Adriatic coast, with Venice being most prone to flooding. It has been noted that some flooding episodes cause significantly different effects along the eastern and western Adriatic coasts, with indications that the difference is related to cross-basin sea-level slope. The present study aims to determine specific atmospheric conditions under which the slope develops and to explore connection with increased sea level along the two coastlines. The analysis is based on sea-level time series recorded at Venice and Bakar over the 1984-2014 interval, from which 38 most intensive storm-surge episodes were selected, and their meteorological backgrounds (ERA-Interim) were studied. The obtained sea-level extremes were grouped into three categories according to their cross-basin sea-level slope: storm surges that slope strongly westward (W type), those that slope eastward (E type) and ordinary storm surges (O type). Results show that the slope is controlled by wind action only, specifically, by the wind component towards a particular coast and by the cross-basin shear of along-basin wind. Meteorological fields were used to force an oceanographic numerical model in order to confirm the empirically established connection between the atmospheric forcing and the slope. Finally, it has been found that the intensity of storm surges along a particular Adriatic coast is determined by an interplay of sea-level slopes in the along and cross-basin directions.

Pitfalls of inferring annual mortality from inspection of published survival curves.

PubMed

Singer, R B

1994-01-01

In many FU articles currently published, results are given primarily in the form of graphs of survival curves, rather than in the form of life table data. Sometimes the authors may comment on the slope of the survival curve as though it were equal to the annual mortality rate (after reversal of the minus sign to a plus sign). Even if no comment of this sort is made, medical directors and underwriters may be tempted to think along similar lines in trying to interpret the significance of the survival curve in terms of mortality. However it is a very serious error of life table methodology to conceive of mortality rate as equal to the negative slope of the survival curve. The nature of the error is demonstrated in this article. An annual mortality rate derived from the survival curve actually depends on two variables: a quotient with the negative slope (sign reversed), delta P/ delta as the numerator, and the survival rate, P, itself as the denominator. The implications of this relationship are discussed. If there are two "parallel" survival curves with the same slope at a given time duration, the lower curve will have a higher mortality rate than the upper curve. A constant slope with increasing duration means that the annual mortality rate also increases with duration. Some characteristics of high initial mortality are also discussed and their relation to different units of FU time.(ABSTRACT TRUNCATED AT 250 WORDS)

A comparative study on seismic response of two unstable rock slopes within same tectonic setting but different activity level

NASA Astrophysics Data System (ADS)

Kleinbrod, Ulrike; Burjánek, Jan; Hugentobler, Marc; Amann, Florian; Fäh, Donat

2017-12-01

In this study, the seismic response of two slope instabilities is investigated with seismic ambient vibration analysis. Two similar sites have been chosen: an active deep-seated slope instability at Cuolm da Vi and the geologically, structurally and morphologically similar, but presently not moving Alp Caschlè slope. Both slopes are located at the upper Vorderrheintal (Canton Graubünden, Switzerland). Ambient vibrations were recorded on both slopes and processed by time-frequency polarization and site-to-reference spectral ratio analysis. The data interpretation shows correlations between degree of disintegration of the rock mass and amplification. However, the ambient vibration analysis conducted, does not allow retrieving a resonance frequency that can be related to the total depth of the instability of Cuolm da Vi. Even though seismic waves can be hardly traced in rock instabilities containing open fractures, it was possible to retrieve a dispersion curve and a velocity profile from the array measurement at Cuolm da Vi due to the high level of disintegration of the rock material down to a depth of about 100 m. From the similar amplification pattern at the two sites, we expect a similar structure, indicating that also the slope at Alp Caschlè was active in the past in a similar manner as Cuolm da Vi. However, a smoother increase of amplification with frequency is observed at Alp Caschlè, which might indicate less disintegration of the rock mass in a particular depth range at this site, when comparing to Cuolm da Vi where a high level of disintegration is observed, resulting from the high activity at the slope. From the frequency-dependent amplification, we can distinguish between two parts within both instabilities, one part showing decreasing disintegration of the rock mass with increasing depth, for the other parts less-fractured blocks are observed. Since the block structures are found in the lower part of the instabilities, they might contribute to the stability of the slopes. Using the velocity profiles, it was possible to estimate the depth of the two largest open fractures (i.e. tension cracks) at Cuolm da Vi.

Normalization for peak oxygen uptake increases the prognostic power of the ventilatory response to exercise in patients with chronic heart failure.

PubMed

Guazzi, Marco; De Vita, Stefano; Cardano, Paola; Barlera, Simona; Guazzi, Maurizio D

2003-09-01

Peak exercise oxygen uptake (peak VO2) and ventilation to CO2 production (VE/VCO2) slope are established prognostic indicators in patients with chronic heart failure (CHF). A high VE/VCO2 slope, however, does not take into account the level of physical performance as expressed by peak VO2. We hypothesized that the prognostic value of a high VE/VCO2 slope may be improved by normalization for peak VO2 (VE/VCO2/VO2). One hundred patients with CHF underwent pulmonary function tests at rest (spirometry and lung diffusion capacity) and maximal cardiopulmonary exercise testing. The prognostic value of VE/VCO2 slope, peak VO2 and VE/VCO2/VO2 was probed prospectively. Twenty-one patients died from cardiac reasons during a mean follow-up of 26 +/- 19 months. Nonsurvivors, compared to survivors, showed a lower peak VO2 (13.6 +/- 4.0 vs 17.5 +/- 4.1 mL x min(-1) x kg(-1), P <.01) and a steeper VE/VCO2 slope (43 +/- 11 vs 31.6 +/- 5.0, P <.01). Nonetheless, in patients whose VE/VCO2 slope exceeded 34 (upper normal limit), there was no correlation with peak VO2 (r = -35, P = not significant). Interestingly 35% of them showed a normal exercise performance (peak VO2 > or =18 mL x min(-1) x kg(-1)). At multivariate analysis, the VE/VCO2 slope showed a prognostic power stronger than that of peak VO2; however, the VE/VCO2/VO2 index retained a prognostic power greater than that of both VE/VCO2 slope and peak VO2. A VE/VCO2/VO2 > or =2.4 signaled cases at higher risk. Discrepancies between VE/VCO2 slope and peak VO2 may generate uncertainty. Normalization of the former by the latter improves outcome prediction and may be considered a simple and effective way for maximizing the clinical applicability of these 2 indicators.

A multi-factor approach for process-based seabed characterization: example from the northeastern continental margin of the Korean peninsula (East Sea)

NASA Astrophysics Data System (ADS)

Cukur, Deniz; Um, In-Kwon; Chun, Jong-Hwa; Kim, So-Ra; Lee, Gwang-Soo; Kim, Yuri; Kong, Gee-Soo; Horozal, Senay; Kim, Seong-Pil

2018-04-01

This study investigates sediment transport and depositional processes from a newly collected dataset comprising sub-bottom chirp profiles, multibeam bathymetry, and sediment cores from the northeastern continental margin of Korea in the East Sea (Japan Sea). Twelve echo-types and eleven sedimentary facies have been defined and interpreted as deposits formed by shallow-marine, hemipelagic sedimentation, bottom current, and mass-movement processes. Hemipelagic sedimentation, which is acoustically characterized by undisturbed layered sediments, appears to have been the primary sedimentary process throughout the study area. The inner and outer continental shelf (<150 m water depth) have been influenced by shallow-marine sedimentary processes. Two slope-parallel canyons, 0.2-2 km wide and up to 30 km long, appear to have acted as possible conduits for turbidity currents from the shallower shelf into the deep basins. Bottom current deposits, expressed as erosional moats immediately below topographic highs, are prevalent on the southern lower slope at water depths of 400-450 m. Mass-movements (i.e., slides/slumps, debris flow deposits) consisting of chaotic facies characterize the lower slope and represent one of the most important sedimentary processes in the study area. Piston cores confirm the presence of mass-transport deposits (MTDs) that are characterized by mud clasts of variable size, shape, and color. Multibeam bathymetry shows that large-scale MTDs are chiefly initiated on the lower slope (400-600 m) with gradients up to 3° and where they produce scarps on the order of 100 m in height. Sandy MTDs also occur on the upper continental slope adjacent to the seaward edge of the shelf terrace. Earthquakes associated with tectonic activity and the development of fluid overpressure is considered as the main conditioning factor for destabilizing the slope sediments. Overall, the sedimentary processes show typical characteristics of a fine-grained clastic slope apron and change down-slope and differ within each physiographic province. Furthermore, the influence of geological inheritance (i.e., structural folds and faults) on geomorphology and sediment facies development is an important additional factor on the lower slopes. Together, these factors provide a rational basis for continental margin seabed characterization.

Predicting assemblages and species richness of endemic fish in the upper Yangtze River.

PubMed

He, Yongfeng; Wang, Jianwei; Lek-Ang, Sithan; Lek, Sovan

2010-09-01

The present work describes the ability of two modeling methods, Classification and Regression Tree (CART) and Random Forest (RF), to predict endemic fish assemblages and species richness in the upper Yangtze River, and then to identify the determinant environmental factors contributing to the models. The models included 24 predictor variables and 2 response variables (fish assemblage and species richness) for a total of 46 site units. The predictive quality of the modeling approaches was judged with a leave-one-out validation procedure. There was an average success of 60.9% and 71.7% to assign each site unit to the correct assemblage of fish, and 73% and 84% to explain the variance in species richness, by using CART and RF models, respectively. RF proved to be better than CART in terms of accuracy and efficiency in ecological applications. In any case, the mixed models including both land cover and river characteristic variables were more powerful than either individual one in explaining the endemic fish distribution pattern in the upper Yangtze River. For instance, altitude, slope, length, discharge, runoff, farmland and alpine and sub-alpine meadow played important roles in driving the observed endemic fish assemblage structure, while farmland, slope grassland, discharge, runoff, altitude and drainage area in explaining the observed patterns of endemic species richness. Therefore, the various effects of human activity on natural aquatic ecosystems, in particular, the flow modification of the river and the land use changes may have a considerable effect on the endemic fish distribution patterns on a regional scale. Copyright 2010 Elsevier B.V. All rights reserved.

Geochemical evidence for enhanced preservation of organic matter in the oxygen minimum zone of the continental margin of northern California during the Late Pleistocene

USGS Publications Warehouse

Dean, Walter E.; Gardner, James V.; Anderson, Roger Y.

1994-01-01

The present upper water mass of the northeastern Pacific Ocean off California has a well-developed oxygen minimum zone between 600 and 1200 m wherein concentrations of dissolved oxygen are less than 0.5 mL/L. Even at such low concentrations of dissolved oxygen, benthic burrowing organisms are abundant enough to thoroughly bioturbate the surface and near-surface sediments. These macro organisms, together with micro organisms, also consume large quantities of organic carbon produced by large seasonal stocks of plankton in the overlying surface waters, which are supported by high concentrations of nutrients within the California Current upwelling system. In contrast to modern conditions of bioturbation, laminated sediments are preserved in upper Pleistocene sections of cores collected on the continental slope at water depths within the present oxygen minimum zone from at least as far north as the California-Oregon border and as far south as Point Conception. Comparison of sediment components in the laminae with those delivered to sediment traps as pelagic marine “snow” demonstrates that the dark-light lamination couplets are indeed annual (varves). These upper Pleistocene varved sediments contain more abundant lipid-rich “sapropelic” (type II) organic matter than the overlying bioturbated, oxidized Holocene sediments. The baseline of stable carbon isotopic composition of the organic matter in these slope cores does not change with time, indicating that the higher concentrations of type II organic matter in the varved sediments represent better preservation of organic matter rather than any change in the source of organic matter.

Instability risk assessment of construction waste pile slope based on fuzzy entropy

NASA Astrophysics Data System (ADS)

Ma, Yong; Xing, Huige; Yang, Mao; Nie, Tingting

2018-05-01

Considering the nature and characteristics of construction waste piles, this paper analyzed the factors affecting the stability of the slope of construction waste piles, and established the system of the assessment indexes for the slope failure risks of construction waste piles. Based on the basic principles and methods of fuzzy mathematics, the factor set and the remark set were established. The membership grade of continuous factor indexes is determined using the "ridge row distribution" function, while that for the discrete factor indexes was determined by the Delphi Method. For the weight of factors, the subjective weight was determined by the Analytic Hierarchy Process (AHP) and objective weight by the entropy weight method. And the distance function was introduced to determine the combination coefficient. This paper established a fuzzy comprehensive assessment model of slope failure risks of construction waste piles, and assessed pile slopes in the two dimensions of hazard and vulnerability. The root mean square of the hazard assessment result and vulnerability assessment result was the final assessment result. The paper then used a certain construction waste pile slope as the example for analysis, assessed the risks of the four stages of a landfill, verified the assessment model and analyzed the slope's failure risks and preventive measures against a slide.

Zonal wavefront reconstruction in quadrilateral geometry for phase measuring deflectometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Lei; Xue, Junpeng; Gao, Bo

2017-06-14

There are wide applications for zonal reconstruction methods in slope-based metrology due to its good capability of reconstructing the local details on surface profile. It was noticed in the literature that large reconstruction errors occur when using zonal reconstruction methods designed for rectangular geometry to process slopes in a quadrilateral geometry, which is a more general geometry with phase measuring deflectometry. In this paper, we present a new idea for the zonal methods for quadrilateral geometry. Instead of employing the intermediate slopes to set up height-slope equations, we consider the height increment as a more general connector to establish themore » height-slope relations for least-squares regression. The classical zonal methods and interpolation-assisted zonal methods are compared with our proposal. Results of both simulation and experiment demonstrate the effectiveness of the proposed idea. In implementation, the modification on the classical zonal methods is addressed. Finally, the new methods preserve many good aspects of the classical ones, such as the ability to handle a large incomplete slope dataset in an arbitrary aperture, and the low computational complexity comparable with the classical zonal method. Of course, the accuracy of the new methods is much higher when integrating the slopes in quadrilateral geometry.« less

Sedimentary condensation and authigenesis

NASA Astrophysics Data System (ADS)

Föllmi, Karl

2016-04-01

Most marine authigenic minerals form in sediments, which are subjected to condensation. Condensation processes lead to the formation of well individualized, extremely thin (< 1m) beds, which were accumulated during extremely long time periods (> 100ky), and which experienced authigenesis and the precipitation of glaucony, verdine, phosphate, iron and manganese oxyhydroxides, iron sulfide, carbonate and/or silica. They usually show complex internal stratigraphies, which result from an interplay of sediment accumulation, halts in sedimentation, sediment winnowing, erosion, reworking and bypass. They may include amalgamated faunas of different origin and age. Hardgrounds may be part of condensed beds and may embody strongly condensed beds by themselves. Sedimentary condensation is the result of a hydrodynamically active depositional regime, in which sediment accumulation, winnowing, erosion, reworking and bypass are processes, which alternate as a function of changes in the location and intensity of currents, and/or as the result of episodic high-energy events engendered by storms and gravity flow. Sedimentary condensation has been and still is a widespread phenomenon in past and present-day oceans. The present-day distribution of glaucony and verdine-rich sediments on shelves and upper slopes, phosphate-rich sediments and phosphorite on outer shelves and upper slopes, ferromanganese crusts on slopes, seamounts and submarine plateaus, and ferromanganese nodules on abyssal seafloors is a good indication of the importance of condensation processes today. In the past, we may add the occurrence of oolitic ironstone, carbonate hardgrounds, and eventually also silica layers in banded iron formations as indicators of the importance of condensation processes. Besides their economic value, condensed sediments are useful both as a carrier of geochemical proxies of paleoceanographic and paleoenvironmental change, as well as the product of episodes of paleoceanographic and paleoenvironmental change themselves.

Malvinas Current Volume Transport at 41°S: A 24 Yearlong Time Series Consistent With Mooring Data From 3 Decades and Satellite Altimetry

NASA Astrophysics Data System (ADS)

Artana, Camila; Ferrari, Ramiro; Koenig, Zoé; Sennéchael, Nathalie; Saraceno, Martin; Piola, Alberto R.; Provost, Christine

2018-01-01

We combined altimetric data and the in situ data sets from three 10 years apart mooring deployments to compute a coherent and accurate volume transport time series of the Malvinas Current (MC) at 41°S. We used a method developed in Koenig et al. (2014) and explored three types of geostrophic shear to estimate the uncertainty derived from the lack of velocity data in the upper 300 m. The mean MC transport over 24 years in the upper 1,500 m is 37.1 ± 2.6 Sv and the standard deviation 6.6 ± 1 Sv. Since 1993, annual mean transports have varied from 32 to 41 Sv and the three in situ records corresponded to low annual mean transports. The MC transport time series is not stationary, its spectral content evolves with time showing significant energy at the 30-110 days, semiannual and annual period. The distribution of the MC volume transport anomalies is asymmetric, negatively skewed with larger negative anomalies than positive anomalies. Several transport maxima appear to result from cyclonic eddies that propagate northwestward following the 4,000-5,000 m isobaths and locally reinforce the circulation on the slope when they reach 41°S. During transport maxima, the northernmost extension of the Subantarctic Front (SAF) remains at its mean location (39.5°S). During minima, the SAF migrates southward of 41°S as positive anomalies shed by the Brazil Current overshoot moves westward onto the slope. Apart from continental trapped waves, changes in the MC volume transport at 41°S show no correlation with upstream conditions on the continental slope.

Coral reef complexes at an atypical windward platform margin: Late Quaternary, southeast Florida

USGS Publications Warehouse

Lidz, B.H.

2004-01-01

Major coral reef complexes rim many modern and ancient carbonate platforms. Their role in margin evolution is not fully understood, particularly when they border a margin atypical of the classic model. Classic windward margins are steeply inclined. The windward margin of southeast Florida is distinct with a very low-gradient slope and a shelf edge ringed with 30-m-high Quaternary outlier reefs on a shallow upper-slope terrace. A newly developed synthesis of temporally well-constrained geologic events is used with surface and subsurface seismic-reflection contours to construct morphogenetic models of four discontinuous reef-complex sequences. The models show uneven subsurface topography, upward and landward buildups, and a previously unreported, rapid, Holocene progradation. The terms backstepped reef-complex margin, backfilled prograded margin, and coalesced reef-complex margin are proposed for sections exhibiting suitable signatures in the stratigraphic record. The models have significant implications for interpretation of ancient analogues. The Florida record chronicles four kinds of geologic events. (1) Thirteen transgressions high enough for marine deposition occurred between ca. 325 ka and the present. Six gave rise to stratigraphically successive coral reef complexes between ca. 185 and ca. 77.8 ka. The seventh reef ecosystem is Holocene. (2) Two primary coral reef architectures built the outer shelf and margin, producing respective ridge-and-swale and reef-and-trough geometries of very different scales. (3) Massive outlier reefs developed on an upper-slope terrace between ca. 106.5 and ca. 80 ka and are inferred to contain corals that would date to highstands at ca. 140 and 125 ka. (4) Sea level remained below elevation of the shelf between ca. 77.8 and ca. 9.6 ka. ?? 2004 Geological Society of America.

A system for telemetering sea wave parameters

NASA Astrophysics Data System (ADS)

Qian, Zhengxu; Jin, Junmo; Suckling, E. E.

1982-04-01

A wave staff to be anchored at sea and containing sensing and telemetering equipment is described. This gives a record at the land station of water level changes due to tides and of waves as they pass the staff. The staff is a 13 metre long PCV tube, the upper half comprising a capacitance with inner plate a foil layer, dielectric the tube wall, and outer electrode the sea. Wave direction is obtained by a separate device comprising a raft moored near to the staff. The raft streams behind its mooring and substantially points into the advancing waves and changes its slope as these pass under it. This slope and its direction referred to magnetic north, are telemetered to the land station to give the direction from which the waves arrive.

Quantitative controls on location and architecture of carbonate depositional sequences: Upper miocene, cabo de gata region, SE Spain

USGS Publications Warehouse

Franseen, E.K.; Goldstein, R.H.; Farr, M.R.

1997-01-01

Sequence stratigraphy, pinning-point relative sea-level curves, and magnetostratigraphy provide the quantitative data necessary to understand how rates of sea-level change and different substrate paleoslopes are dominant controls on accumulation rate, carbonate depositional sequence location, and internal architecture. Five third-order (1-10 my) and fourth-order (0.1-1.0 my) upper Miocene carbonate depositional sequences (DS1A, DS1B, DS2, DS3, TCC) formed with superimposed higher-frequency sea-level cycles in an archipelago setting in SE Spain. Overall, our study indicates when areas of high substrate slope (> 15??) are in shallow water, independent of climate, the location and internal architecture of carbonate deposits are not directly linked to sea-level position but, instead, are controlled by location of gently sloping substrates and processes of bypass. In contrast, if carbonate sediments are generated where substrates of low slope ( 15.6 cm/ky to ??? 2 cm/ky and overall relative sea level rose at rates of 17-21.4 cm/ky. Higher frequency sea-level rates were about 111 to more than 260 cm/ky, producing onlapping, fining- (deepening-) upward cycles. Decreasing accumulation rates resulted from decreasing surface area for shallow-water sediment production, drowning of shallow-water substrates, and complex sediment dispersal related to the archipelago setting. Typical systems tract and parasequence development should not be expected in "bypass ramp" settings; facies of onlapping strata do not track base level and are likely to be significantly different compared to onlapping strata associated with coastal onlap. Basal and upper DS2 reef megabreccias (indicating the transition from cool to warmer climatic conditions) were eroded from steep upslope positions and redeposited downslope onto areas of gentle substrate during rapid sea-level falls (> 22.7 cm/ky) of short duration. Such rapid sea-level falls and presence of steep slopes are not conducive to formation of forced regressive systems tracts composed of down-stepping reef clinoforms. The DS3 reefal platform formed where shallow water coincided with gently sloping substrates created by earlier deposition. Slow progradation (0.39-1.45 km/my) is best explained by the lack of an extensive bank top, progressively falling sea level, and low productivity resulting from siliciclastic debris and excess nutrients shed from nearby volcanic islands. Although DS3 strata were deposited during a third-order relative sea-level cycle, a typical transgressive systems tract is not recognizable, indicating that the initial relative rise in sea level was too rapid (??? 19 cm/ky). Downstepping reefs, forming a forced regressive systems tract, were deposited during the relative sea-level fall at the end of DS3, indicating that relatively slow rates of fall (10 cm/ky or less) over favorable paleoslope conditions are conducive to generation of forced regressive systems tracts consisting of downstepping reef clinoforms. The TCC sequence consists of four shallow-water sedimentary cycles that were deposited during a 400 ky to 100 ky time span. Such shallow-water cycles, typical of many platforms, form only where shallow water intersects gently sloping substrates. The relative thicknesses of cycles (< 2 m to 15 m thick), magnitudes of relative sea-level fluctuations associated with each cycle (25-30 m), high rates of relative sea-level fluctuations (minimum of 25-120 cm/ky), and the widespread distribution of similar TCC cycles in the Mediterranean and elsewhere are supportive of a glacio-eustatic

Quantitative controls on location and architecture of carbonate depositional sequences: upper miocene, cabo de gata region, se Spain

USGS Publications Warehouse

Franseen, E.K.; Goldstein, R.H.; Farr, M.R.

1998-01-01

Sequence stratigraphy, pinning-point relative sea-level curves, and magnetostratigraphy provide the quantitative data necessary to understand how rates of sea-level change and different substrate paleoslopes are dominant controls on accumulation rate, carbonate depositional sequence location, and internal architecture. Five third-order (1-10 my) and fourth-order (0.1-1.0 my) upper Miocene carbonate depositional sequences (DS1A, DS1B, DS2, DS3, TCC) formed with superimposed higher-frequency sea-level cycles in an archipelago setting in SE Spain. Overall, our study indicates when areas of high substrate slope (> 15??) are in shallow water, independent of climate, the location and internal architecture of carbonate deposits are not directly linked to sea-level position but, instead, are controlled by location of gently sloping substrates and processes of bypass. In contrast, if carbonate sediments are generated where substrates of low slope ( 15.6 cm/ky to ??? 2 cm/ky and overall relative sea level rose at rates of 17-21.4 cm/ky. Higher frequency sea-level rates were about 111 to more than 260 cm/ky, producing onlapping, fining- (deepening-) upward cycles. Decreasing accumulation rates resulted from decreasing surface area for shallow-water sediment production, drowning of shallow-water substrates, and complex sediment dispersal related to the archipelago setting. Typical systems tract and parasequence development should not be expected in "bypass ramp" settings; facies of onlapping strata do not track base level and are likely to be significantly different compared to onlapping strata associated with coastal onlap. Basal and upper DS2 reef megabreccias (indicating the transition from cool to warmer climatic conditions) were eroded from steep upslope positions and redeposited downslope onto areas of gentle substrate during rapid sea-level falls (> 22.7 cm/ky) of short duration. Such rapid sea-level falls and presence of steep slopes are not conducive to formation of forced regressive systems tracts composed of downstepping reef clinoforms. The DS3 reefal platform formed where shallow water coincided with gently sloping substrates created by earlier deposition. Slow progradation (0.39-1.45 km/my) is best explained by the lack of an extensive bank top, progressively falling sea level, and low productivity resulting from siliciclastic debris and excess nutrients shed from nearby volcanic islands. Although DS3 strata were deposited during a third-order relative sea-level cycle, a typical transgresse??e systems tract is not recognizable, indicating that the initial relative rise in sea level was too rapid (??? 19 cm/ky). Downstepping reefs, forming a forced regressive systems tract, were deposited during the relative sea-level fall at the end of DS3, indicating that relatively slow rates of fall (10 cm/ky or less) over favorable paleoslope conditions are conducive to generation of forced regressive systems tracts consisting of downstepping reef clinoforms. The TCC sequence consists of four shallow -water sedimentary cycles that were deposited during a 400 ky to 100 ky time span. Such shallow-water cycles, typical of many platforms, form only where shallow water intersects gently sloping substrates. The relative thicknesses of cycles (< 2 m to 15 m thick), magnitudes of relative sea-level fluctuations associated with each cycle (25-30 m), high rates of relative sea-level fluctuations (minimum of 25-120 cm/ky), and the widespread distribution of similar TCC cycles in the Mediterranean and elsewhere are supportive of a glacio-eustati

Investigation of upper mantle seismic discontinuities beneath the Indian Ocean using array seismology methods

NASA Astrophysics Data System (ADS)

van Driel, J.; Reiss, A. S.; Thomas, C.

2016-12-01

The topography of upper mantle seismic discontinuities can be used to constrain regional variations in composition and temperature of the Earths mantle. The 410 km discontinuity is caused by the solid-solid phase transition from olivine to wadsleyite. Due to its positive Clapeyron slope, the discontinuity is depressed in hot regimes. The phase transition from ringwoodite to bridgemanite and magnesiowüstite in contrast has a negative Clapeyron slope and therefore is elevated when hot material is present. Cold material is expected to yield an opposing topographic signature, culminating in an elevated 410 km and a depressed 660 km discontinuity. As part of the RHUM-RUM project (Réunion Hotspot and Upper Mantle - Réunions Unterer Mantel) we extract relevant geophysical parameters, by investigating the properties of upper mantle seismic discontinuities beneath the Indian Ocean. The topography of the 410 and 660 km discontinuities, which define the upper and lower bounds of the mantle transition zone, have been mapped using PP and SS underside reflections. This study has utilised over 8500 events with Mw ≥ 5.8, distributed over the entire Indian Ocean. Our robust data set yields a dense coverage of points, which are defined by consistently crossing ray paths. Array seismology methods, such as vespagrams and slowness-backazimuth analysis, are used to enhance the signal-to-noise-ratio and detect and identify weak precursor signals. The differential travel times are corrected for crustal features and converted into depth values of the discontinuities by comparing the measured travel times with theoretical ones derived from ray tracing through the 1D reference Earth model ak135. A `travel-time' stacking method has also been applied for 4° radius bins around each of the bounce points. The addition of a secondary method derives greater stability of our results and allows an enhanced error analysis procedure. In order to better constrain the mineralogical processes taking place within the mantle transition zone, amplitude ratios, polarities and velocity gradients have also been investigated.

Lead Isotopes from the Upper Mississippi Valley District: A Regional Perspective

USGS Publications Warehouse

Millen, Timothy M.; Zartman, Robert E.; Heyl, Allen Van

1995-01-01

New lead isotopic data on galena from within and peripheral to the Upper Mississippi Valley lead-zinc district make it possible, by extending coverage to outlying locations, to trace the pathway traversed by the mineralizing fluids beyond the boundary of the main district. All but one of the samples exhibit elevated ratios of the radiogenic isotopes typical of the Upper Mississippi Valley ore deposits; 206PbP04Pb ranges from 19.38 to 24.46, 207PbP04Pb ranges from 15.73 to 16.24, and 208PbP04Pb ranges from 39.24 to 43.69. Galena from the Pints quarry near Waterloo, Iowa, has distinctly lower values of these ratios and may not be related paragenetically to the other samples. Otherwise, the lowest ratios are for samples in the southern part of the region in north-central Illinois, and the highest ratios are for samples to the northeast of the main district in the vicinity of Madison, Wisconsin. Thus, an isotopic pattern rather similar to that observed originally by Heyl and others (1966) prevails regionally, although the predominant fluid flow is now believed to have emanated from the Illinois Basin rather than from the Forest City Basin. Metal-bearing brines being driven northward out of the Illinois Basin probably played the key role in mineralization of the Upper Mississippi Valley district. Both the new and the previously reported lead ratios for the Upper Mississippi Valley district are plotted on 207PbP04Pb and Pb208/pb204Pb versus 206PbP04Pb diagrams, which permit their comparison and the calculation of refined slopes for the expanded data set. A two-stage model age for the time of mineralization can be determined from the 207PbP04Pb_Pb206/Pb204 slope, provided that the source age of the lead is known. With our limited know ledge of this source age, the time of mineralization cannot be tightly constrained but is permissive of a Permian or younger lateral secretion event, as suggested by other geochronological results.

Study of rainfall-induced landslide: a review

NASA Astrophysics Data System (ADS)

Tohari, A.

2018-02-01

Rainfall-induced landslides pose a substantial risk to people and infrastructure. For this reason, there have been numerous studies to understand the landslide mechanism. Most of them were performed on the numerical analysis and laboratory experiment. This paper presents a review of existing research on field hydrological condition of soil slopes leading to the initiation of rainfall-induced landslide. Existing methods to study field hydrological response of slopes are first reviewed, emphasizing their limitations and suitability of application. The typical hydrological response profiles in the slope are then discussed. Subsequently, some significant findings on hydrological condition leading to rainfall-induced landslides are summarized and discussed. Finally, several research topics are recommended for future study.

The role of topography and surface cover upon soil formation along hillslopes in arid climates

NASA Astrophysics Data System (ADS)

Yair, Aaron

1990-09-01

Two north-facing soil toposequences were selected from within the northern Negev desert, Israel, where average annual rainfall ranges from 70 to 200 mm. Both slopes are composed of an upper rocky and a lower colluvial section. Similar trends were found along both slopes. A high salt content was characteristic of soils at the top of the slope; salinity decreased downslope within the rocky slope section. The opposite occurred along the colluvial slopes, with salinity increasing sharply downslope. At any location along the slopes the northernmost soil toposequence site (160 mm average annual rainfall) represents, from a pedological point of view, an environment which is far more arid than its climatologically drier, more southern counterpart. The explanation provided for the variation of soil proporties at the scale of single hillslopes and at the regional scale is the same. It is contended that water input into the soil, and therefore leaching intensity, is positively related to the ratio of bedrock/soil cover. Rocky areas have limited infiltration, thus yielding high runoff rates into adjoining soil-covered areas, and contribute to water concentration, deeper infiltration and leaching intensity. Soil or sediment-covered areas having relatively high absorption capacities will experience reduced runoff, shallow infiltration and decreased water availability for leaching. This leads over time to salt accumulation at a shallow depth. The decrease in rock/soil ratio downslope within the colluvium is therefore held responsible for the corresponding increase in salinity. Similarly, the greater salinity of the soils in the northern site is explained by the fact that its rock/soil ratio is lower than in the southern area. The theoretical and practical implications regarding the relationship between climatic change and landscape evolution in arid areas are briefly discussed.

Quantitative assessment of pedodiversity and soil erosion within a karst sinkhole in the dry steppe subzone

NASA Astrophysics Data System (ADS)

Smirnova, M. A.; Gennadiev, A. N.

2017-08-01

A detailed study of the soil cover of a sinkhole (300 m2) in the dry steppe landscape of the Bogdinsk-Baskunchak Natural Reserve in Astrakhan oblast has been performed, and the factors of its differentiation have been analyzed. The indices of pedodiversity have been calculated and compared for karst sinkholes in the dry steppe and northern taiga landscapes. Quantitative parameters of the lateral migration of solid soil substances on the slopes of the sinkhole have been determined. The rate of soil erosion decreases from the slope of southern aspect to the slopes of western, northern, and eastern aspects. On the average, it is estimated at 0.4 mm/yr. The average rate of accumulation of solid substances on the lower parts of the slopes and in the bottom of the sinkhole reaches 0.74 mm/yr. A comparative analysis of the soil properties attests to their dependence on the particular position of a given soil within the sinkhole. Downward the slopes of the sinkhole, full-profile brown arid soils (Cambic Calcisols) are replaced by sierozem-like soils (Haplic Calcisols), light-humus poorly developed soils (Luvisols), lithozems (Leptosols), and stratified soils (stratozems, or Colluvic Regosols). The soils within the upper ring-shape soil microzone are more diverse and contrasting with respect to their morphological, physical, chemical, and physicochemical properties. The degree of soil contrasts decreases down the slopes of the sinkhole towards its bottom. The studied sinkhole is characterized by considerable pedodiversity. Quantitative parameters of pedodiversity for the sinkhole in the dry steppe zone are higher than those form the sinkholes in the northern taiga zone.

Physical Mechanisms Controlling Upper Tropospheric Water Vapor as Revealed by MLS Data from UARS

NASA Technical Reports Server (NTRS)

Newell, Reginald E.; Douglass, Anne (Technical Monitor)

2002-01-01

The third year and final report on the physical mechanisms controlling upper tropospheric water vapor revealed by the Microwave Limb Sounder (MLS) on the Upper Atmosphere Research Satellite (UARS) is presented.

New figuring model based on surface slope profile for grazing-incidence reflective optics

DOE PAGES

Zhou, Lin; Huang, Lei; Bouet, Nathalie; ...

2016-08-09

Surface slope profile is widely used in the metrology of grazing-incidence reflective optics instead of surface height profile. Nevertheless, the theoretical and experimental model currently used in deterministic optical figuring processes is based on surface height, not on surface slope. This means that the raw slope profile data from metrology need to be converted to height profile to perform the current height-based figuring processes. The inevitable measurement noise in the raw slope data will introduce significant cumulative error in the resultant height profiles. As a consequence, this conversion will degrade the determinism of the figuring processes, and will have anmore » impact on the ultimate surface figuring results. To overcome this problem, an innovative figuring model is proposed, which directly uses the raw slope profile data instead of the usual height data as input for the deterministic process. In this article, first the influence of the measurement noise on the resultant height profile is analyzed, and then a new model is presented; finally a demonstration experiment is carried out using a one-dimensional ion beam figuring process to demonstrate the validity of our approach.« less

Modeling an internal gear pump

NASA Astrophysics Data System (ADS)

Chen, Zongbin; Xu, Rongwu; He, Lin; Liao, Jian

2018-05-01

Considering the nature and characteristics of construction waste piles, this paper analyzed the factors affecting the stability of the slope of construction waste piles, and established the system of the assessment indexes for the slope failure risks of construction waste piles. Based on the basic principles and methods of fuzzy mathematics, the factor set and the remark set were established. The membership grade of continuous factor indexes is determined using the "ridge row distribution" function, while that for the discrete factor indexes was determined by the Delphi Method. For the weight of factors, the subjective weight was determined by the Analytic Hierarchy Process (AHP) and objective weight by the entropy weight method. And the distance function was introduced to determine the combination coefficient. This paper established a fuzzy comprehensive assessment model of slope failure risks of construction waste piles, and assessed pile slopes in the two dimensions of hazard and vulnerability. The root mean square of the hazard assessment result and vulnerability assessment result was the final assessment result. The paper then used a certain construction waste pile slope as the example for analysis, assessed the risks of the four stages of a landfill, verified the assessment model and analyzed the slope's failure risks and preventive measures against a slide.

Absolute surface reconstruction by slope metrology and photogrammetry

NASA Astrophysics Data System (ADS)

Dong, Yue

Developing the manufacture of aspheric and freeform optical elements requires an advanced metrology method which is capable of inspecting these elements with arbitrary freeform surfaces. In this dissertation, a new surface measurement scheme is investigated for such a purpose, which is to measure the absolute surface shape of an object under test through its surface slope information obtained by photogrammetric measurement. A laser beam propagating toward the object reflects on its surface while the vectors of the incident and reflected beams are evaluated from the four spots they leave on the two parallel transparent windows in front of the object. The spots' spatial coordinates are determined by photogrammetry. With the knowledge of the incident and reflected beam vectors, the local slope information of the object surface is obtained through vector calculus and finally yields the absolute object surface profile by a reconstruction algorithm. An experimental setup is designed and the proposed measuring principle is experimentally demonstrated by measuring the absolute surface shape of a spherical mirror. The measurement uncertainty is analyzed, and efforts for improvement are made accordingly. In particular, structured windows are designed and fabricated to generate uniform scattering spots left by the transmitted laser beams. Calibration of the fringe reflection instrument, another typical surface slope measurement method, is also reported in the dissertation. Finally, a method for uncertainty analysis of a photogrammetry measurement system by optical simulation is investigated.

Sequence stratigraphic applications to deep-water exploration in the Makassar Strait, offshore East Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malacek, S.J.; Reaves, C.M.; Atmadja, W.S.

1994-07-01

A sequence stratigraphic study was conducted to help evaluate the exploration potential of the Makassar PSC, offshore East Kalimantan, Indonesia. The PSC is on the present-day slope in water depths of 500-3000 ft and borders the large oil and gas fields of the Mahakam delta. The study provided important insights on reservoir distribution, trapping style, and seismic hydrocarbon indicators. Lowstand deposition on a slope modified by growth faulting and shale diapirism controlled reservoir distribution within the prospective late Miocene section. Three major lowstand intervals can be seismically defined and tied to deep-water sands in nearby wells where log character andmore » biostratigraphic data support the seismic system tract interpretation. The three intervals appear to correlate with third-order global lowstand events and are consistent with existing sequence stratigraphic schemes for the shelf and upper slope in the Makassar area. Seismic mapping delineated lowstand features, including incised valleys and intraslope to basin-floor thicks. Regional information on positions of middle-late Miocene delta lobes and shelf edges, helped complete the picture for sand sources, transport routes, and depocenters.« less

Upper Neoproterozoic-Lower Cambrian sedimentary successions in the Central Iberian Zone (Spain): sequence stratigraphy, petrology and chemostratigraphy. Implications for other European zones

NASA Astrophysics Data System (ADS)

Valladares, M. I.; Barba, P.; Ugidos, J. M.; Colmenero, J. R.; Armenteros, I.

The Upper Neoproterozoic-Lower Cambrian sedimentary succession in the central areas of the Central Iberian Zone has been subdivided into 12 mostly siliciclastic lithostratigraphic units, ranging in thickness between 1800 and 3900m. The lithology and facies of each unit are described and the facies associations are interpreted. The facies resulted mainly from turbidity currents and debris flows and, to a lesser extent, from submarine slides and traction flows. The facies associations suggest that sedimentation took place in slope and base-of-slope environments. Two depositional sequences are recognized, separated by a type-1 unconformity. The lower sequence is of Late Neoproterozoic age (units I-IV) and exhibits lowstand, transgressive, and highstand systems tracts. Most of the upper sequence is probably of Early Cambrian age (units V-XII). It begins at the base of unit V and possibly ends with the Tamames Limestone Formation. The upper sequence records a lowstand systems tract and minor-order sea-level oscillations. In the Cambrian units there are higher amounts of feldspar and smaller quantities of intrabasinal clasts than in the Neoproterozoic units. The modal data plot close to the Q-L and Qm-Lt sides of Q-F-L and Qm-F-Lt triangular diagrams, suggesting a provenance from a recycled orogen evolving into a provenance from a craton interior towards the top of the succession. The chemical results, based mainly on Al2O3, TiO2, Zr, and Nb abundances in shales from all the units, strongly suggest a gradual compositional change within this sedimentary succession. Together with the petrological data, the chemical results do not reveal any obvious coeval volcanic contribution to the sediments. On the basis of the chemical data, a comparison is made with other European zones containing detrital sediments composed of reworked crustal components.

Sedimentology and sequence stratigraphy of the Cretaceous Nanushuk, Seabee, and Tuluvak formations exposed on Umiat Mountain, north-central Alaska

USGS Publications Warehouse

Houseknecht, David W.; Schenk, Christopher J.

2005-01-01

Upper Cretaceous strata of the upper part of the Nanushuk Formation, the Seabee Formation, and the lower part of the Tuluvak Formation are exposed along the Colville River on the east flank of Umiat Mountain in north-central Alaska. The Ninuluk sandstone, which is the uppermost unit of the Nanushuk Formation, displays a vertical succession of facies indicative of deposition in an upward-deepening estuarine through shoreface setting. A marine-flooding surface lies between the Ninuluk sandstone and organic-rich shale of the basal part of the Seabee Formation. The Ninuluk sandstone and the lower part of the Seabee Formation are interpreted as components of a transgressive-systems tract. The lowest, well-exposed strata in the Seabee Formation are a succession of shoreface sandstone beds in the middle of the formation. Integration of outcrop information and the Umiat No. 11 well log suggests that this sandstone succession rests on a sequence boundary and is capped by a marine-flooding surface. The sandstone succession is interpreted as a lowstand-systems tract. The upper part of the Seabee Formation includes a thick interval of organic-rich shale deposited in a dysaerobic offshore environment, and the gradational Seabee-Tuluvak contact is a coarsening-upward shale-to-sandstone succession deposited in a prodelta/delta-front environment. The observation that the upper part of the Seabee Formation correlates with seismic clinoforms suggests that dysaerobic conditions extended well up onto the prodelta slope during intervals of transgression and highstand. Correlation of the Umiat Mountain outcrop section with well logs and seismic data suggests that sequence boundaries and lowstand shoreface deposits may be common in the Seabee Formation and that wave action may have been important in transporting sand to the paleoshelf margin. These conclusions may contribute to an enhanced understanding of sand distribution in prospective lowstand turbidite deposits in the subsurface of the central North Slope of Alaska.

Uncertainties in Galactic Chemical Evolution Models

DOE PAGES

Cote, Benoit; Ritter, Christian; Oshea, Brian W.; ...

2016-06-15

Here we use a simple one-zone galactic chemical evolution model to quantify the uncertainties generated by the input parameters in numerical predictions for a galaxy with properties similar to those of the Milky Way. We compiled several studies from the literature to gather the current constraints for our simulations regarding the typical value and uncertainty of the following seven basic parameters: the lower and upper mass limits of the stellar initial mass function (IMF), the slope of the high-mass end of the stellar IMF, the slope of the delay-time distribution function of Type Ia supernovae (SNe Ia), the number ofmore » SNe Ia per M ⊙ formed, the total stellar mass formed, and the final mass of gas. We derived a probability distribution function to express the range of likely values for every parameter, which were then included in a Monte Carlo code to run several hundred simulations with randomly selected input parameters. This approach enables us to analyze the predicted chemical evolution of 16 elements in a statistical manner by identifying the most probable solutions along with their 68% and 95% confidence levels. Our results show that the overall uncertainties are shaped by several input parameters that individually contribute at different metallicities, and thus at different galactic ages. The level of uncertainty then depends on the metallicity and is different from one element to another. Among the seven input parameters considered in this work, the slope of the IMF and the number of SNe Ia are currently the two main sources of uncertainty. The thicknesses of the uncertainty bands bounded by the 68% and 95% confidence levels are generally within 0.3 and 0.6 dex, respectively. When looking at the evolution of individual elements as a function of galactic age instead of metallicity, those same thicknesses range from 0.1 to 0.6 dex for the 68% confidence levels and from 0.3 to 1.0 dex for the 95% confidence levels. The uncertainty in our chemical evolution model does not include uncertainties relating to stellar yields, star formation and merger histories, and modeling assumptions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cote, Benoit; Ritter, Christian; Oshea, Brian W.

Here we use a simple one-zone galactic chemical evolution model to quantify the uncertainties generated by the input parameters in numerical predictions for a galaxy with properties similar to those of the Milky Way. We compiled several studies from the literature to gather the current constraints for our simulations regarding the typical value and uncertainty of the following seven basic parameters: the lower and upper mass limits of the stellar initial mass function (IMF), the slope of the high-mass end of the stellar IMF, the slope of the delay-time distribution function of Type Ia supernovae (SNe Ia), the number ofmore » SNe Ia per M ⊙ formed, the total stellar mass formed, and the final mass of gas. We derived a probability distribution function to express the range of likely values for every parameter, which were then included in a Monte Carlo code to run several hundred simulations with randomly selected input parameters. This approach enables us to analyze the predicted chemical evolution of 16 elements in a statistical manner by identifying the most probable solutions along with their 68% and 95% confidence levels. Our results show that the overall uncertainties are shaped by several input parameters that individually contribute at different metallicities, and thus at different galactic ages. The level of uncertainty then depends on the metallicity and is different from one element to another. Among the seven input parameters considered in this work, the slope of the IMF and the number of SNe Ia are currently the two main sources of uncertainty. The thicknesses of the uncertainty bands bounded by the 68% and 95% confidence levels are generally within 0.3 and 0.6 dex, respectively. When looking at the evolution of individual elements as a function of galactic age instead of metallicity, those same thicknesses range from 0.1 to 0.6 dex for the 68% confidence levels and from 0.3 to 1.0 dex for the 95% confidence levels. The uncertainty in our chemical evolution model does not include uncertainties relating to stellar yields, star formation and merger histories, and modeling assumptions.« less

PHYSICAL MECHANISMS OF CLEAR-AIR TURBULENCE,

DTIC Science & Technology

An attempt was made to test the hypothesis that reports of clear-air turbulence ( CAT ) on March 14-15, 1962, were associated with narrow layers (upper...did not contradict the hypothe sis, as many reports of CAT were made in sloping baroclinic or adiabatic layers. In any case, the Richardson numbers...index of CAT intensity which should be proportional to the energy of CAT is derived from the eddy energy equation. (Author)

Monitoring surface currents and transport variability in Drake Passage using altimetry and hydrography

NASA Astrophysics Data System (ADS)

Pavic, M.; Cunningham, S. A.; Challenor, P.; Duncan, L.

2003-04-01

Between 1993 and 2001 the UK has completed seven occupations of WOCE section SR1b from Burdwood Bank to Elephant Island across Drake Passage. The section consists of a minimum of 31 full depth CTD stations, shipboard ADCP measurements of currents in the upper 300m, and in three of the years full depth lowered ADCP measurements at each station. The section lies under the satellite track of ERS2. The satellite altimeter can determine the along track slope of the sea surface relative to a reference satellite pass once every 35 days. From this we can calculate the relative SSH slope or geostrophic surface current anomalies. If we measure simultaneously with any satellite pass, we can estimate the absolute surface geostrophic current for any subsequent pass. This says that by combining in situ absolute velocity measurements - the reference velocities with altimetry at one time the absolute geostrophic current can be estimated on any subsequent (or previous) altimeter pass. This is the method of Challenor et al. 1996, though they did not have the data to test this relationship. We have seven estimates of the surface reference velocity: one for each of the seven occupations of the WOCE line. The difference in any pair of reference velocities is predicted by the difference of the corresponding altimeter measurements. Errors in combining the satellite and hydrographic data are estimated by comparing pairs of these differences: errors arise from the in situ observations and from the altimetric measurements. Finally we produce our best estimates of eight years of absolute surface geostrophic currents and transport variability along WOCE section SR1 in Drake Passage.

Influences of elevated heating effect by the Himalaya on the changes in Asian summer monsoon

NASA Astrophysics Data System (ADS)

He, Bian

2017-04-01

Based on a series of topographical and thermal sensitivity experiments, the physical processes on the changes of Asian summer monsoon caused by the Himalaya elevated heating were investigated. Six different Himalaya-Iranian Plateau mountain heights were used: 0%, 20%, 40%, 60%, 80%, and 100% in the first group (called HIM). The no sensible heating experiments (called HIM_NS) were also performed with the same six mountain heights but the surface sensible heating was not allowed to heat the atmosphere. The results indicate that the elevated heating effect of Himalaya gradually intensified when Himalaya uplift. The establishment of SASM over South Asian land which is characterized by the strong precipitation over South slope of Tibetan Plateau and the huge warm anticyclone in the upper troposphere are in proportion to the elevated heating effect of Himalaya. Further analysis suggests that the surface heat fluxes over Himalaya keep almost unchanged during the uplifting, but the lifted condensation level reduces gradually over the regions where the mountain uplift. The condensation moisturing increases correspondingly and leads to the increase of latent heating in the upper troposphere. Therefore, the positive feedback between the moist convection over south slope of Himalaya and monsoon circulation over Indian sub-continent forms and the successive precipitation over South Asian land is maintained.

Subducting plate geology in three great earthquake ruptures of the western Alaska margin, Kodiak to Unimak

USGS Publications Warehouse

von Huene, Roland E.; Miller, John J.; Weinrebe, Wilhelm

2012-01-01

Three destructive earthquakes along the Alaska subduction zone sourced transoceanic tsunamis during the past 70 years. Since it is reasoned that past rupture areas might again source tsunamis in the future, we studied potential asperities and barriers in the subduction zone by examining Quaternary Gulf of Alaska plate history, geophysical data, and morphology. We relate the aftershock areas to subducting lower plate relief and dissimilar materials in the seismogenic zone in the 1964 Kodiak and adjacent 1938 Semidi Islands earthquake segments. In the 1946 Unimak earthquake segment, the exposed lower plate seafloor lacks major relief that might organize great earthquake rupture. However, the upper plate contains a deep transverse-trending basin and basement ridges associated with the Eocene continental Alaska convergent margin transition to the Aleutian island arc. These upper plate features are sufficiently large to have affected rupture propagation. In addition, massive slope failure in the Unimak area may explain the local 42-m-high 1946 tsunami runup. Although Quaternary geologic and tectonic processes included accretion to form a frontal prism, the study of seismic images, samples, and continental slope physiography shows a previous history of tectonic erosion. Implied asperities and barriers in the seismogenic zone could organize future great earthquake rupture.

Epibiotic relationships on Zygochlamys patagonica (Mollusca, Bivalvia, Pectinidae) increase biodiversity in a submarine canyon in Argentina

NASA Astrophysics Data System (ADS)

Schejter, Laura; López Gappa, Juan; Bremec, Claudia Silvia

2014-06-01

The continental slope of the southern SW Atlantic Ocean has many distinguishable deep submarine canyons, varying in depth and extension. The benthic fauna within one of them, detected in April 2005 by means of a multibeam SIMRAD EM1002 sonar, and located at 43°35‧S to 59°33‧W, 325 m depth, was studied to discuss faunal affinities with the neighbouring Patagonian scallop fishing grounds located at upper slope depths. In order to add faunal information to the previous general study, we studied the epibiotic species settled on Patagonian scallops (the dominant species in the area) collected in the reference sampling site using a 2.5-m mouth-opening dredge, 10 mm mesh size. We sampled 103 scallops with shell heights between 22 and 69 mm; epibionts were recorded on both valves. We found 53 epibiotic taxa, which were most conspicuous on the upper valve. Bryozoa was the most diverse group (34 species) while Polychaeta was the most abundant group, recorded on 94% of the scallops. Stylasteridae (2 species) and Clavulariidae (Cnidaria) conform newly recorded epibionts on Z. patagonica and the sponge Tedania (Tedaniopsis) infundibuliformis also represents a new record for the SW Atlantic Ocean.

The Characteristics and triggering Factors of the October 2013 Obudu International Tourist Centre catastrophic Landslide South-East Nigeria

NASA Astrophysics Data System (ADS)

Fukuoka, Hiroshi; Igwe, Ogbonnaya

2015-04-01

The October 2013 catastrophic landslides at the Obudu international tourist zone south-east Nigeria destroyed resources worth several millions of dollars and trapped international tourist who were later rescued by a helicopter. Intense rainfall caused several slope failures on the steep slopes of the hills. These landslides occurred after several days of heavy rain (> 600 mm) and were the first reported slope failures in this region. The failures were on a predominantly metamorphic terrain and only on slopes adjacent to the main road. They occurred as slides, not debris flow, but produced a wide range of casualties. The failures were of residual materials (about 1 m thick) obtained from weathering of schist. One of the landslides involved the movement of about 70,000 m3 debris for 8.6 m with depth of slip surface of 6 m. Another, which produced the most fatality initiated on a slope greater than 40o and displaced about 77, 000 m3. It had a runout length of 60 m, width of 98 m, depth to slip surface of 8 m and depositional area of about 2,500 m2. Had the opposite slope bounding the other side of the road not hindered the movement of debris, the runout distance could have been larger. The research found that all the landslides occurred on slope-portions composed of schist rather than gneiss or granite. Slip surfaces developed within the regolith and the shear zone was characterized by the presence of silty materials supported by clayey matrix. Field observations indicated that the failures generally developed as localized translational slides within the semi-consolidated, cohesive soil units (with high plasticity and low strength) within the upper to middle weathered zone of the schist. The increase in pore pressure arising from elevated water table during rainfall created instability by weakening the shear strength along the failure plane. However, differences in permeability favored the formation of perched water table which eventually triggered sliding.

GIS for Predicting the Avalanche Zones in the Mountain Regions of Kazakhstan

NASA Astrophysics Data System (ADS)

Omirzhanova, Zh. T.; Urazaliev, A. S.; Aimenov, A. T.

2015-10-01

Foothills of Trans Ili Alatau is a recreational area with buildings and sports facilities and resorts, sanatoriums, etc. In summer and winter there are a very large number of skiers, climbers, tourists and workers of organizations which located in the mountains. In this regard, forecasting natural destructive phenomena using GIS software is an important task of many scientific fields. The formation of avalanches, except meteorological conditions, such as temperature, wind speed, snow thickness, especially affecting mountainous terrain. Great importance in the formation of avalanches play steepness (slope) of the slope and exposure. If steep slopes contribute to the accumulation of snow in some places, increase the risk of flooding of the slope, the various irregularities can delay an avalanche. According to statistics, the bulk of the avalanche is formed on the slopes steeper than 30°. In the course of research a 3D model of the terrain was created with the help of programs ArcGIS and Surfer. Identified areas with steep slopes, the exposure is made to the cardinal. For dangerous terrain location is divided into three groups: favorable zone, danger zone and the zone of increased risk. The range of deviations from 30-45° is dangerous, since the angle of inclination of more than 30°, there is a maximum thickness of sliding snow, water, the upper layer of the surface and there is an increase rate of moving array, and the mountain slopes at an angle 450 above are the area increased risk. Created on DTM data are also plotted Weather Service for the winter of current year. The resulting model allows to get information upon request and display it on map base, assess the condition of the terrain by avalanches, as well as to solve the problem of life safety in mountainous areas, to develop measures to prevent emergency situations and prevent human losses.

Mechanical conditions and modes of paraglacial deep-seated gravitational spreading in Valles Marineris, Mars

NASA Astrophysics Data System (ADS)

Makowska, Magdalena; Mège, Daniel; Gueydan, Frédéric; Chéry, Jean

2016-09-01

Deep-seated gravitational spreading (DSGS) affects the slopes of formerly glaciated mountain ridges. On Mars, DSGS has played a key role in shaping the landforms of the giant Valles Marineris troughs. Though less spectacular, DSGS is common in terrestrial orogens, where understanding its mechanics is critical in the light of the ongoing climate change because it is a potential source of catastrophic landslides in deglaciated valleys. We conducted parametric numerical studies in order to identify important factors responsible for DSGS initiation. DSGS models are computed using an elastoviscoplastic finite element code. Using ADELI's software, we reproduce topographic ridge spreading under the effect of valley unloading. Two types of spreading topographic ridges are investigated, homogeneous or with horizontal rheological layering. We find that gravitational instabilities are enhanced by high slopes, which increase gravitational stress, and low friction and cohesion, which decrease yield stress. In the unlayered ridge, instability is triggered by glacial unloading with plastic strain concentration inside the ridge and at the base of the high slopes. Vertical fractures develop in the upper part of the slope, potentially leading to fault scarps. Ridge homogeneity promotes a deformation mode controlled by uphill-facing normal faulting and basal bulging. In the second case, the ridge encompasses horizontal geological discontinuities that induce rock mass anisotropy. Discontinuity located at the base of the slope accumulates plastic strain, leading to the formation of a sliding plane evolving into a landslide. The presence of a weak layer at ridge base therefore promotes another slope deformation mode ending up with catastrophic failure. Mechanical conditions and slope height being equal, these conclusions can probably be extrapolated to Earth. Compared with Mars, DSGS on Earth is inhibited because terrestrial topographic gradients are lower than in Valles Marineris, an effect counterbalanced by increased gravitational stress, where the intensity of deformation is enhanced because of the Earth gravity potential.

Pattern of distribution and diversity of demersal assemblages in the central Mediterranean Sea

NASA Astrophysics Data System (ADS)

Colloca, F.; Cardinale, M.; Belluscio, A.; Ardizzone, G.

2003-03-01

A highly diversified mix of fish species, cephalopods and crustaceans, together with several macro-epibenthic organisms, compose trawl catches in the Mediterranean Sea. Management of Mediterranean trawling needs a multispecies approach that considers the community and not the single species as the basic unit of the analysis. While many studies have correlated several environmental factors to the spatial organizations of demersal organisms, few have focused on the role of macro-epibenthic communities in structuring demersal assemblages. In this paper, the following hypotheses were tested: (1) there are discrete demersal assemblages in the central Mediterranean Sea; (2) the distribution and diversity of demersal communities does not change on small temporal scales (1 year); (3) the demersal assemblages were segregated across both different epibenthic assemblages and depth gradients. Shallow stations were separated into coastal and middle-deep shelf assemblages while stations on the slope formed three main assemblages: slope edge, upper slope and middle slope assemblages. The demersal community did not show a substantial change at the small temporal scale. Sandy, sand-muddy and detritic epibenthic communities characterized coastal shelf assemblages, while epibenthic assemblage on muddy bottoms were dominant in the deeper areas of the shelf. A well-defined difference in macro-epibenthic faunal associations among stations on the slope (depth >200 m) was not found. Depth appeared to affect diversity of the main taxa of demersal organisms in different ways. Teleostean diversity did not show any trend with depth, the number of cephalopod species increased on the shelf and decreased on the slope while crustacean and elasmobranch species richness increased significantly from the shelf to the middle slope. The strong correlation shown in this study between epifaunal benthic communities and demersal fish assemblages requires the formulation of an ecosystem-based management for the Mediterranean Sea trawl fisheries. The existence of such biological diversity certainly contributes to the Mediterranean ecosystem health and its conservation should become one of the main objective of demersal resources management in the future.

IMPULSIVE PHASE CORONAL HARD X-RAY SOURCES IN AN X3.9 CLASS SOLAR FLARE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Qingrong; Petrosian, Vahe, E-mail: qrchen@gmail.com, E-mail: vahep@stanford.edu

2012-03-20

We present the analysis of a pair of unusually energetic coronal hard X-ray (HXR) sources detected by the Reuven Ramaty High Energy Solar Spectroscopic Imager during the impulsive phase of an X3.9 class solar flare on 2003 November 3, which simultaneously shows two intense footpoint (FP) sources. A distinct loop top (LT) coronal source is detected up to {approx}150 keV and a second (upper) coronal source up to {approx}80 keV. These photon energies, which were not fully investigated in earlier analysis of this flare, are much higher than commonly observed in coronal sources and pose grave modeling challenges. The LTmore » source in general appears higher in altitude with increasing energy and exhibits a more limited motion compared to the expansion of the thermal loop. The high-energy LT source shows an impulsive time profile and its nonthermal power-law spectrum exhibits soft-hard-soft evolution during the impulsive phase, similar to the FP sources. The upper coronal source exhibits an opposite spatial gradient and a similar spectral slope compared to the LT source. These properties are consistent with the model of stochastic acceleration of electrons by plasma waves or turbulence. However, the LT and FP spectral index difference (varying from {approx}0 to 1) is much smaller than commonly measured and than that expected from a simple stochastic acceleration model. Additional confinement or trapping mechanisms of high-energy electrons in the corona are required. Comprehensive modeling including both kinetic effects and the macroscopic flare structure may shed light on this behavior. These results highlight the importance of imaging spectroscopic observations of the LT and FP sources up to high energies in understanding electron acceleration in solar flares. Finally, we show that the electrons producing the upper coronal HXR source may very likely be responsible for the type III radio bursts at the decimetric/metric wavelength observed during the impulsive phase of this flare.« less

Trench-parallel variations in Pacific and Indo-Australian crustal velocity structure due to Louisville Ridge seamount subduction

NASA Astrophysics Data System (ADS)

Stratford, W. R.; Knight, T. P.; Peirce, C.; Watts, A. B.; Grevemeyer, I.; Paulatto, M.; Bassett, D.; Hunter, J.; Kalnins, L. M.

2012-12-01

Variations in trench and forearc morphology, and lithospheric velocity structure are observed where the Louisville Ridge seamount chain subducts at the Tonga-Kermadec Trench. Subduction of these seamounts has affected arc and back-arc processes along the trench for the last 5 Myr. High subduction rates (80 mm/yr in the north, 55 mm/yr in the south), a fast southwards migrating collision zone (~180 km/myr), and the obliquity of the subducting plate and the seamount chain to the trench, make this an ideal location to study the effects of seamount subduction on lithospheric structure. The "before and after" subduction regions have been targeted by several large-scale geophysical projects in recent years; the most recent being the R/V Sonne cruise SO215 in 2011. The crust and upper mantle velocity structure observed in profiles along strike of the seamount chain and perpendicular to the trench from this study, are compared to a similar profile from SO195, recorded ~100 km to the north. The affects of the passage of the seamounts through the subduction system are indicated by velocity anomalies in the crust and mantle of the overriding plate. Preliminary results indicate that in the present collision zone, mantle velocities (Pn) are reduced by ~5%. Around 100 km to the north, where seamounts are inferred to have subducted ~1 Myr ago, a reduction of 7% in mantle P-wave velocity is observed. The width of the trench slope and elevation of the forearc also vary along strike. At the collision zone a >100 km wide collapse region of kilometre-scale block faults comprise the trench slope, while the forearc is elevated. The elevated forearc has a 5 km think upper crust with a Vp of 2.5-5.5 km/s and the collapse zone also has upper crustal velocities as low as 2.5 km/s. To the east in the Pacific Plate, lower P-wave velocities are also observed and attributed to serpentinization due to deep fracturing in the outer trench high. Large bending faults permeate the crust and the Osbourn Seamount, currently on the verge of subduction, is fractured stepwise down into the trench. Pn velocities in the hinge zone of the Pacific Plate are as low as 7.3 km/s indicating that fracturing and serpentinization may also extend to sub-crustal depths. Finally, trench-parallel variations in subduction zone velocity structure are used to infer the degree to which seamount subduction has altered the physical state of the Pacific and Indo-Australian plates both pre- and post subduction.

Record of Subducting Topography revealed in 3D Seismic Imaging of Pleistocene unconformities, offshore Southern Costa Rica

NASA Astrophysics Data System (ADS)

Edwards, J. H.; Kluesner, J. W.; Silver, E. A.

2015-12-01

3D seismic reflection data (CRISP) collected across the southern Costa Rica forearc reveals broad, survey-wide erosional events in the upper ~1 km of slope sediments in the mid-slope to outer shelf. The upper 0-280 m of continuous, weakly deformed sediments, designated by IODP Expedition 344 as structural domain I, is bounded by a major erosional event, (CRISP-U1, dated near 1 Ma), suggesting wave-plain erosion from the present shelf break out to 25 km seaward, to a present-day water depth of 900-1300 m. The eastern toe of its surface is characterized by a large drainage system, likely including submarine channels that eroded to depths >1500 m below present-day water depth. CRISP-U1 is variably uplifted by a series of fault propagation folds and cut by an intersecting array of normal faults. Another, major erosional event, (CRISP-M1, approximately 2 Ma) extended from the outer shelf to the mid slope and removed 500-1000 m of material. Overlying CRISP-M1 is up to 1 km of sediments that are more deformed by fault propagation folds, back thrusts, and intersecting arrays of normal faults. Unconformities with smaller areal extent are variably found in these overlying sediments across the mid-slope to outer shelf, at present-day water depths >220 m. Below CRISP-M1, sediments are more densely deformed and also contain major unconformities that extend survey-wide. Both unconformities, CRISP-U1 and CRISP-M1, are encountered in well U1413 and are demarcated by major benthic foraminifera assemblage changes at 149 mbsf and ~504 mbsf (Harris et al., 2013, Proceeding of the IODP, Volume 344).CRISP-M1 is likely correlative to the major sediment facies and benthic foraminifera assemblage change found in U1379 at ~880 mbsf (Vannuchi et al., 2013). The unconformities and intersecting array of normal faults may demarcate the passing of topography on the downgoing Cocos plate, episodically lifting and then subsiding the Costa Rica margin, with amplitudes up to about 1 km.

Synchrony measure for a neuron driven by excitatory and inhibitory inputs and its adaptation to experimentally-recorded data.

PubMed

Zavou, Christina; Kkoushi, Antria; Koutsou, Achilleas; Christodoulou, Chris

2017-11-01

The aim of the current work is twofold: firstly to adapt an existing method measuring the input synchrony of a neuron driven only by excitatory inputs in such a way so as to account for inhibitory inputs as well and secondly to further appropriately adapt this measure so as to be correctly utilised on experimentally-recorded data. The existing method uses the normalized pre-spike slope (NPSS) of the membrane potential, resulting from observing the slope of depolarization of the membrane potential of a neuron prior to the moment of crossing the threshold within a short period of time, to identify the response-relevant input synchrony and through it to infer the operational mode of a neuron. The first adaptation of NPSS is made such that its upper bound calculation accommodates for the higher possible slope values caused by the lower average and minimum membrane potential values due to inhibitory inputs. Results indicate that when the input spike trains arrive randomly, the modified NPSS works as expected inferring that the neuron is operating as a temporal integrator. When the input spike trains arrive in perfect synchrony though, the modified NPSS works as expected only when the level of inhibition is much higher than the level of excitation. This suggests that calculation of the upper bound of the NPSS should be a function of the ratio between excitatory and inhibitory inputs in order to be able to correctly capture perfect synchrony at a neuron's input. In addition, we effectively demonstrate a process which has to be followed when aiming to use the NPSS on real neuron recordings. This process, which relies on empirical observations of the slope of depolarisation for estimating the bounds for the range of observed interspike interval lengths, is successfully applied to experimentally-recorded data showing that through it both a real neuron's operational mode and the amount of input synchrony that caused its firing can be inferred. Copyright © 2017 Elsevier B.V. All rights reserved.

Dissolution rates of subsoil limestone in a doline on the Akiyoshi-dai Plateau, Japan: An approach from a weathering experiment, hydrological observations, and electrical resistivity tomography

NASA Astrophysics Data System (ADS)

Akiyama, Sanae; Hattanji, Tsuyoshi; Matsushi, Yuki; Matsukura, Yukinori

2015-10-01

This study aims at estimating the controlling factors for the denudation rates of limestone, which often forms solution dolines on karst tablelands. Our approaches include (1) electrical resistivity tomography (ERT) to reveal shallow subsurface structures and hydrological settings, (2) automated monitoring of volumetric water content in soil profiles and manual measurements of subsurface CO2 concentrations and soil water chemistry, and (3) a field weathering experiment using limestone tablets with the micro-weight loss technique for determining current denudation rates. The field experiment and monitoring were carried out over 768 days from 2009-2011 at four sites with varying topographic and hydrological conditions along the sideslope of a doline on the Akiyoshi-dai karst plateau in SW-Japan. The installation depths of the limestone tablets were 15 cm or 50 cm below the slope surface. The soil moisture conditions varied site by site. Water-saturated conditions continued for 40-50% of the whole experimental period at 50-cm depth of upper and middle sites, while only 0-10% of the experimental period was water-saturated at the other sites. Chemical analysis revealed that the soil water was chemically unsaturated with calcite for all the sites. Spatial differences in concentrations of CO2 in soil pore air were statistically less significant. The denudation rates of the buried limestone tablets were 17.7-21.9 mg cm- 2 a- 1 at the upper and middle slopes, where the soil was water-saturated for a long time after precipitation. The lowest denudation of 3.9 mg cm- 2 a- 1 was observed on lower slopes where soil was not capable of maintaining water at a near saturation level even after precipitation. Statistical analysis revealed that the denudation rates of the tablets were strongly controlled by the duration for which soil pores were saturated by water (the conditions defined here are degrees of water saturation greater than 97%). Electrical resistivity tomography indicated that areas with high soil moisture conditions were located at the deeper zone on the lower slopes and the bottom of the doline, where denudation would be faster.

Evaluation of Elevation, Slope and Stream Network Quality of SPOT Dems

NASA Astrophysics Data System (ADS)

El Hage, M.; Simonetto, E.; Faour, G.; Polidori, L.

2012-07-01

Digital elevation models are considered the most useful data for dealing with geomorphology. The quality of these models is an important issue for users. This quality concerns position and shape. Vertical accuracy is the most assessed in many studies and shape quality is often neglected. However, both of them have an impact on the quality of the final results for a particular application. For instance, the elevation accuracy is required for orthorectification and the shape quality for geomorphology and hydrology. In this study, we deal with photogrammetric DEMs and show the importance of the quality assessment of both elevation and shape. For this purpose, we produce several SPOT HRV DEMs with the same dataset but with different template size, that is one of the production parameters from optical images. Then, we evaluate both elevation and shape quality. The shape quality is assessed with in situ measurements and analysis of slopes as an elementary shape and stream networks as a complex shape. We use the fractal dimension and sinuosity to evaluate the stream network shape. The results show that the elevation accuracy as well as the slope accuracy are affected by the template size. Indeed, an improvement of 1 m in the elevation accuracy and of 5 degrees in the slope accuracy has been obtained while changing this parameter. The elevation RMSE ranges from 7.6 to 8.6 m, which is smaller than the pixel size (10 m). For slope, the RMSE depends on the sampling distance. With a distance of 10 m, the minimum slope RMSE is 11.4 degrees. The stream networks extracted from these DEMs present a higher fractal dimension than the reference river. Moreover, the fractal dimension of the extracted networks has a negligible change according to the template size. Finally, the sinuosity of the stream networks is slightly affected by the change of the template size.

78 FR 56650 - Boundary Description and Final Map for Sandy Wild and Scenic River, Upper Portion, Mount Hood...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-13

... DEPARTMENT OF AGRICULTURE Forest Service Boundary Description and Final Map for Sandy Wild and...: Notice of availability. SUMMARY: In accordance with section 3(b) of the Wild and Scenic Rivers Act, the... Sandy Wild and Scenic River, Upper Portion, to Congress. DATES: The boundaries and classification of the...

Geomorphic Thresholds of Submarine Canyons Along the U.S. Atlantic Continental Margin

NASA Astrophysics Data System (ADS)

Brothers, D. S.; ten Brink, U. S.; Andrews, B. D.; Chaytor, J. D.

2011-12-01

Vast networks of submarine canyons and associated channels are incised into the U.S. Atlantic continental slope and rise. Submarine canyons form by differential erosion and deposition, primarily from sedimentary turbidity flows. Theoretical and laboratory studies have investigated the initiation of turbidity flows and their capacity to erode and entrain sedimentary material at distances far from the shelf edge. The results have helped understand the nature of turbidite deposits on the continental slope and rise. Nevertheless, few studies have examined the linkages between down-canyon sediment transport and the morphology of canyon/channel networks using mesoscale analyses of swath bathymetry data. We present quantitative analysis of 100-m resolution multibeam bathymetry data spanning ~616,000 km2 of the slope and rise between Georges Banks and the Blake Plateau (New England to North Carolina). Canyons are categorized as shelf-indenting or slope-confined based on spatial scale, vertical relief and connection with terrestrial river systems during sea level low stands. Shelf-indenting canyons usually represent the trunk-canyon of submerged channel networks. On the rise, shelf-indenting canyons have relatively well-developed channel-levees and sharp inner-thalwag incision suggesting much higher frequency and volume of turbidity flows. Because of the similarities between submarine canyon networks and terrestrial river systems, we apply methods originally developed to study fluvial morphology. Along-canyon profiles are extracted from the bathymetry data and the power-law relationship between thalwag gradient and drainage area is examined for more than 180 canyons along an ~1200 km stretch of the US Atlantic margin. We observe distinct thresholds in the power-law relationship between drainage area and gradient. Almost all canyons with heads on the upper slope contain at least two linear segments when plotted in log-log form. The first segment along the upper slope is flat (constant gradient, low area). The second segment dips (exponentially decreasing gradient with increasing area). We interpret the transition between the two segments to be either diffusive creep/landslide processes that evolve into turbidity flows or the boundary that separates up-canyon infilling from relic, lower-canyon incision. Furthermore, the threshold occurs at a nearly constant drainage area regardless of location and morphology of the drainage network. This suggests that time-averaged erosion rate in submarine canyons depends on frequency of turbidity flows, which in turn depends on the volume of unstable sediments deposited near canyon heads and along canyon walls. We find that the gradient-area relationship does not follow a power-law in shelf-indenting canyons, most likely due to allogenic processes of the continental shelf and linkage to terrestrial river discharge.

Objective determination of the predefined duration of a constant-load diagnostic tests in arterial claudication.

PubMed

Mahe, Guillaume; Abraham, Pierre; Zeenny, Maya; Bruneau, Antoine; Vielle, Bruno; Leftheriotis, Georges

2010-04-01

The predefined duration to arbitrarily stop the tests during constant-load treadmill exercise is a subject of debate and widely variable in the literature. We hypothesized that the upper and lower limits for predefined durations of constant-load 3.2 km/hour 10% grade tests could be derived from the distribution of walking distances observed on a treadmill in a population of subjects referred for claudication or from the optimal cutoff point distance on a treadmill to confirm a limitation self-reported by history. We conducted a retrospective analysis using a referral center, institutional practice, and ambulatory patients. We studied 1290 patients (86% male), 62.1 +/- 11.2 years of age, 169 +/- 8 cm height, 75.7 +/- 14.2 kg weight. Patients performed a standard constant-load treadmill test: 3.2 km hour(-1), 10% slope, maximized to 1000 meters (approximately 20 minutes). We analyzed the maximal walking distance self-reported (MWD(SR)) by history and the maximal walking distance measured on the treadmill (MWD(TT)). Patients reporting MWD(SR) >or=1000 meters were considered unlimited by history. Only 197 patients (15.3%) completed the 20-minute treadmill test. Among the 504 patients who did not stop before 250 meters, 47.8% stopped within the next 250 meters (were unable to walk 500 meters). This proportion falls to 7.5% among the 213 patients who did not stop before 750 meters. When the final goal was to estimate whether the treadmill test can discriminate patients with or without limitation by history, area under the receiver operating characteristic (ROC) curve was 0.809 +/- 0.016 (95% confidence interval [CI], 0.778-0.841; P < .0001), the best diagnostic performance was attained for an MWD(TT) of 299 meters (approximately 6.15 minutes). In patients undergoing constant-load treadmill exercise with a protocol of 3.2 km hour(-1) and 10% slope: a predefined duration of 7 minutes could be proposed as a lower limit for the predefined duration of the tests specifically if one aims at confirming the limitation by history with treadmill testing. Owing to the low risk that patients that could walk 750 meters (approximately 15 minutes) will have to stop in the next 250 meters, 15 minutes seems a reasonable upper limit for the predefined test duration in clinical routine.

77 FR 61632 - Final Environmental Impact Statement for Cattle Point Road Relocation, San Juan Island National...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-10

... Impact Statement (Final EIS) for alternatives designed to respond to coastal bluff erosion that threatens... the southeastern tip of San Juan Island, is threatened by coastal erosion at the base of the slope... (relative to coastal erosion) of each of the three action alternatives is estimated at approximately 100...

Methodology for Elaborating Regional Susceptibility Maps of Slope Instability: the State of Guerrero (mexico) Case Study

NASA Astrophysics Data System (ADS)

González Huesca, A. E.; Ferrés, D.; Domínguez-M, L.

2013-05-01

Numerous cases of different types of slope instability occur every year in the mountain areas of México. Sometimes these instabilities severely affect the exposed communities, roads and infrastructure, causing deaths and serious material damage, mainly in the states of Puebla, Veracruz, Oaxaca, Guerrero and Chiapas, at the central and south sectors of the country. The occurrence of the slope instability is the result of the combination of climatic, geologic, hydrologic, geomorphologic and anthropogenic factors. The National Center for Disaster Prevention (CENAPRED) is developing several projects in order to offer civil protection authorities of the Mexican states some methodologies to address the hazard assessment for different natural phenomena in a regional level. In this framework, during the past two years, a methodology was prepared to construct susceptibility maps for slope instability at regional (≤ 1:100 000) and national (≤ 1:1 000 000) levels. This research was addressed in accordance to the criteria established by the International Association of Engineering Geology, which is the highest international authority in this topic. The state of Guerrero has been taken as a pilot scheme to elaborate the susceptibility map for slope instability at a regional level. The major constraints considered in the methodology to calculate susceptibility are: a) the slope of the surface, b) the geology and c) the land use, which were integrated using a Geographic Information System (GIS). The arithmetic sum and weighting factors to obtain the final susceptibility map were based on the average values calculated in the individual study of several cases of slope instability occurred in the state in the past decade. For each case, the evaluation format proposed by CENAPRED in 2006 in the "Guía Básica para la elaboración de Atlas Estatales y Municipales de Peligros y Riesgos" to evaluate instabilities in a local level, was applied. The resulting susceptibility map shows that the central and east-central sectors of the state of Guerrero are those with higher values of susceptibility to slope instability. Future work will elaborate the hazard maps of slope instability for the state of Guerrero using and combining the information of susceptibility obtained with the data of the trigger factors, such as precipitation and seismicity, for different periods of recurrence. The final goal is that this methodology can be applied to other states of the country, in order to nourish and enhance their Atlas of hazards and risk.

Seafloor morphology of the continental slope in front the Petacalco Bay and its tsunamigenic relationship at the Mexican sector of the Middle American subduction zone

NASA Astrophysics Data System (ADS)

Mortera-Gutierrez, C. A.; Bandy, W. L.; Millan-Motolinia, C.; Ponce-Nuñez, F.; Ortega-Ramirez, J.

2014-12-01

The recent occurrence of offshore, large, earthquake ruptures in the western limit of the Guerrero Seismic Gap and the scattered data of seafloor morphology of the continental slope along this sector at the Mexican Mid American subduction zone have encouraged the UNAM marine geophysical group to initiate a mapping program at the Guerrero margin, from the shelf break to the Middle American Trench. The main objective of this initiative is to have a complete cover of the seafloor morphology of the Guerrero slope as the background data for comparative studies of the seafloor deformation in case of future offshore earthquake ruptures in this region. At he first stage of this initiative, we have mapped the continental slope in front the Petacalco Bay, west of the Guerrero Seismic Gap, where three important large earthquakes occurred and caused great damages in Mexico City: Petatlán earthquake (Mw=7.6) at 1979, Michoacán earthquake (Mw=8.1) and its aftershock (Mw=7.9) at 1985. Geophysical results of two campaigns carry in 2012 (MAMRIV12) and 2013 (BABPET13) on board the BO EL PUMA are presented which include multibeam data and subbottom profiles. These data sets cover an area between 101°W and 103°W, and from the shelf-slope break to the trench. The multibeam chart shows details of the hydrological erosion induced by many submarine cannons at the upper slope, whereas the seafloor relief in the lower slope is dominated by tectonic structures. The subbottom profiles and the seafloor morphology evidence zones of big slumps and faults. For first time the Rio Balsas submarine cannon is completed chart, reaching the trench basin. The river course is deflected, possibly by shear faulting. There are slump sites near the trench that probably one is associated to the 1925 tsunami at Zihuatanejo, Guerrero. The 1985 Michoacán aftershock was accompany by a small Tsunami. At that time, the lack of morphology data in this slope inhibited further studies of seafloor-deformation and its tsunamigenic relationship. Funding providing by UNAM-DGAPA-PAPIIT grants: IN115613 and IN115513

Prevention of Proximal Junctional Kyphosis: Are Polyaxial Pedicle Screws Superior to Monoaxial Pedicle Screws at the Upper Instrumented Vertebrae?

PubMed

Wang, Hui; Ding, Wenyuan; Ma, Lei; Zhang, Lijun; Yang, Dalong

2017-05-01

Evidence regarding whether the polyaxial pedicle screws at the upper instrumented vertebrae (UIV) are superior to monoaxial pedicle screws in prevention of proximal junctional kyphosis (PJK) is not clear. The aim of this study was therefore to explore the influence of different types of pedicle screws at UIV on the incidence of PJK. We reviewed retrospectively 242 patients surgically treated with instrumented segmental posterior spinal fusion at a minimum of 4 motion segments. Polyaxial pedicle screws were used at UIV in 125 patients (polyaxial group), and monoaxial pedicle screws were used at UIV in 117 patients (monoaxial group). According to the occurrence of PJK at final follow-up, patients in both the polyaxial and monoaxial groups were then divided into 2 subgroups: PJK and no proximal junctional kyphosis (NPJK). To investigate the risk factors of PJK, 2 categorized variables were analyzed statistically: 1) patient characteristics: age, sex, body mass index (BMI), bone mineral density (BMD), sagittal vertical axis (SVA), thoracic kyphosis, thoracolumbar junctional angle, lumbar lordosis (LL), pelvic incidence, pelvic tilt, and sacral slope. 2) Surgical variables: Changes of radiographic parameters include the SVA, thoracic kyphosis, thoracolumbar junctional, LL, pelvic incidence, pelvic tilt, sacral slope, pedicle-upper end plate angle, the number of instrumented levels, and the most proximal and distal levels of the instrumentation. PJK was developed in 26 of 117 patients (22.2%) in the monoaxial group and 30 of 125 patients (24.0%) in the polyaxial group. Until the final follow-up, there was no significant difference in the incidence of PJK (χ2 = 0.107, P = 0.734) between the monoaxial and polyaxial groups. There was no significant difference in patient characteristics and surgical variables between the 2 groups, except the proximal junctional angle change (P = 0.031). In the monoaxial group, there were no significant differences in patient characteristics between the PJK and NPJK subgroups, except BMI (P = 0.042) and BMD (P = 0.037). There were no significant differences in change of radiographic parameters, except SVA change (P = 0.036), proximal junctional angle change (P = 0.029), LL change (P = 0.025), and lower instrumented vertebrae location (P = 0.036). Multivariate logistic regression analysis revealed that obesity, osteoporosis, lower instrumented vertebra at sacrum, and LL change >10 degrees were independently associated with PJK. In the polyaxial group, there were no significant differences in patient characteristics between the PJK and NPJK subgroups, except BMI (P = 0.032) and BMD (P = 0.040). There were no significant differences in change of radiographic parameters between the PJK and NPJK subgroups, except P-UP angle (P = 0.037) and lower instrumented vertebrae location (P = 0.017). Multivariate logistic regression analysis revealed that obesity, osteoporosis, and lower instrumented vertebra at sacrum were independently associated with PJK. Polyaxial pedicle screws at UIV is not superior to monoaxial pedicle screws in prevention of PJK. Obesity, osteoporosis, and lower instrumented vertebra at sacrum are risk factors for PJK in all the patients. Excessive LL reconstruction is the unique risk factor of PJK when monoaxial pedicle screws were used at UIV. Copyright © 2017 Elsevier Inc. All rights reserved.

Constraints on Dark Matter Annihilation by Synchrotron Emission based on Planck Data

NASA Astrophysics Data System (ADS)

Muanglay, Chalit; Wechakama, Maneenate; Cantlay, Brandon K.

2017-09-01

Synchrotron emission can be a good probe for dark matter particles in the Milky Way. We have investigated the production of electrons and positrons in the Milky Way within the context of dark matter annihilation. Upper limits on the relevant cross-section are obtained by comparing synchrotron emission in the microwave bands with Planck data. According to our results, the dark matter annihilation cross-section into electron-positron pairs should not be higher than the canonical value for a thermal relic if the mass of the dark matter candidate is smaller than a few GeV. In addition, we also look for constraints on the inner slope of dark matter density profile in the Milky Way. Our results indicate that the inner slope of dark matter profile is between 1 to 1.5.

Chemical spring water measurements coupled with 2d u.d.e.c hydromechanical modelling as an investigation methodology of water infiltration influence on large moving rock mass stability : application to the "la clapière" landslide (france, 06).

NASA Astrophysics Data System (ADS)

Cappa, F.; Guglielmi, Y.; Soukatchoff, V. M.; Mudry, J.; Bertrand, C.; Charmoille, A.

2003-04-01

We present an investigation method of water infiltration influence on Large Moving Rock Mass (LMRM) stability. In the case of huge unstable mountainous slopes, it has been clearly shown that the main driving of instability is gravity and that the major triggering and increasing factor is water located in interstices and fractures of rocks (Noverraz &al., 1998). More particularly, groundwater originates from a localized hydro-mechanical deformation inside fractures that can induce a generalized destabilization of large rock masses (Guglielmi, 1999). However, the understanding of groundwater mechanical effects on landslides and their neighbouring environment is rendered more complex given the large anisotropy of the rock mass as well as the difficulties to apply classic hydrogeological investigation methods in a moving environment. For these reasons, we developped an indirect investigation method based on chemical groundwater measurements coupled with a two-dimensional hydro-mechanical modelling with the Universal Distinct Element Code (UDEC) numerical program, taking the example of the La Clapière landslide (Alpes-Maritimes, France). The methodology we develop firstly establishes a hydro-mechanical conceptual scheme through the analysis of geological, hydrogeological, hydrogeochemistry and landslide velocity measurements. Then, a two-dimensional numerical modelling with UDEC was performed to test the influence of the locations and the intensities of water infiltrations on the hydro-mechanical behaviour of La Clapière’s slope. A geological and hydrogeological analysis reveals a perched saturated zone connected by large conducting-flow fractures to a basal aquifer. The correlations of spring water chemistry data and meteorological events on the slope highlight a large variability of groundwater transits in the slope in time (transit durations of 1 to 21 days) and in space. Infiltration transients correlate with landslide accelerations. Infiltration yields range between 0.4 and 0.8 l.s-1. The most intensive hydro-mechanical response of the landslide is linked to snowmelt in a stable area in the upper part of the slope located between 1800 and a 2500 m high. On the one hand modeling hydro-mechanical effects with UDEC considers a model corresponding to a slope without any unstable zone, and on the other hand, a model including a failure surface in order to simulate the current instability. In the two numerical tests, calculations show that the most unstabilizing water infiltration corresponds to water infiltrations located in the middle part of the slope for weak flow rates of 0.75 l.s-1. This is due to the water infiltration influence on the spatial distribution of strain fields. This result fits with field measurements. This methodology can easily be applied to the monitoring of landslide movements. As it gives relevant information on the spatial and temporal effects of various meteoric infiltrations, it can be applied to improve remedial protocols. This work was partly funded by the French National Program on Natural Hazards (PNRN) and Retina European Program. Guglielmi Y., 1999. Apport de la mesure des couplages hydromécaniques à la connaissance hydrogéologique des réservoirs fissurés. Habilitation à diriger des recherches, Université de Franche-Comté, E.A. 2642 Géosciences : Déformation, Écoulement, Transfert. 187 p. Noverraz F., BonnardC., Dupraz H., and Huguenin L., 1998. Grands glissements de versants et climat. Rapport final PNR 31, vdf hochschulverlag AG an der ETH Zürich, 314 p.

Structure and Neotectonics of the Southern Chile Forearc 35°S - 40°S

NASA Astrophysics Data System (ADS)

Geersen, Jacob; Völker, David; Weinrebe, Wilhelm; Krastel-Gudegast, Sebastian; Behrmann, Jan H.

2010-05-01

The Southern Chile Forearc exhibits an extreme level of neotectonic deformation. On-land studies have documented a pronounced segmentation in the region 36°S - 41°S. However, information on the seaward continuation of the individual segments towards the Chile Trench is rare, as direct observations end at the coastline and are replaced by a less dense set of marine geophysical data. In this study we use swath bathymetric data combined with high and low-frequency reflection seismic data as well as results from heat-flow measurements to: (A) map and identify active deformation structures and investigate their spatial distribution, and (B) analyse the factors controlling segmentation along the Southern Chile Forearc. Considering the region 35°S to 40°S we found evidence for a division into four major segments; Concepcion North, Concepcion South, Nahuelbuta, and Tolten (from North to South). Within all four segments, the lower continental slope is dissected by distinct margin-parallel thrust ridges overlying active landward-dipping thrust faults, indicating the presence of an active accretionary prism. The middle and upper slope, however, shows major differences between the four segments. The Concepcion North Segment is dominated by a large margin-parallel thrust ridge. The Concepcion South Segment shows large up to 600 m high north-south aligned normal fault scarps highlighting east-west extension. The change from thrust to normal faulting domains is accompanied by a drastic decrease in surface heat-flow by a factor of up to four. Further south in the Nahuelbuta Segment, east-west trending active thrust ridges indicate north-south compression of this part of the forearc. Shortening in this segment is not only limited to the middle and upper slope, but includes the entire marine forearc and occurs perpendicular to the direction of plate convergence. In the southernmost Tolten Segment the middle and upper continental slope shows no signs of compressive or extensional deformation. For the factors controlling segmentation our data suggest that when considering the whole forearc variations in the overriding plate such as the position of continental fault zones are responsible for the large scale tectonic segmentation. The east-west oriented shortening structures in the Nahuelbuta Segment (perpendicular to the direction of plate motion) probably originate from the collision of the Chiloe Microplate with a marine buttress situated below the Concepcion South Segment. The Chiloe Microplate represents a 1000 km-sized forearc sliver, which is kinematically decoupled from stable South America along the Liquine-Ofqui and Lanalhue Fault Zones. The important transition from wholesale forearc compression to extension observed between the two Concepcion segments, however, is more likely related to plate boundary processes, i.e. different degrees of coupling and/or friction in the plate boundary itself.

Rip Channels, Megacusps, and Shoreline Change: Measurements and Modeling

DTIC Science & Technology

2010-06-01

and October 2007 with correlation coefficients (r) and slopes (m) in upper left corner. While the correlation of CDIP - and ADCP-predicted rms wave...about ±5º). In spite of this, CDIP -model- based predictions of offshore radiation stress, Syx,s, and sediment transport rates, qs, in the surf zone...73 Figure 12. Wave roses showing mean wave directions and frequencies at 15 m depth, offshore of Stilwell site, as estimated by CDIP

Amounts and spatial distribution of downed woody debris, snags, windthrow, and forest floor mass within streamside management zones occurring in shortleaf pine stands five years after harvesting

Treesearch

Hal Liechty

2007-01-01

Shortleaf pine (Pinus echinata Mill.) is a dominant tree species in pine and pine-hardwood forest communities located on ridges and upper- to mid-slope positions in the Ouachita Mountains. The stream reaches located in these stands flow infrequently and are classified as ephemeral or intermittent, have low stream orders, and have relatively narrow...

Deep seismic structure and tectonics of northern Alaska: Crustal-scale duplexing with deformation extending into the upper mantle

USGS Publications Warehouse

Fuis, G.S.; Murphy, J.M.; Lutter, W.J.; Moore, Thomas E.; Bird, K.J.; Christensen, N.I.

1997-01-01

Seismic reflection and refraction and laboratory velocity data collected along a transect of northern Alaska (including the east edge of the Koyukuk basin, the Brooks Range, and the North Slope) yield a composite picture of the crustal and upper mantle structure of this Mesozoic and Cenozoic compressional orogen. The following observations are made: (1) Northern Alaska is underlain by nested tectonic wedges, most with northward vergence (i.e., with their tips pointed north). (2) High reflectivity throughout the crust above a basal decollement, which deepens southward from about 10 km depth beneath the northern front of the Brooks Range to about 30 km depth beneath the southern Brooks Range, is interpreted as structural complexity due to the presence of these tectonic wedges, or duplexes. (3) Low reflectivity throughout the crust below the decollement is interpreted as minimal deformation, which appears to involve chiefly bending of a relatively rigid plate consisting of the parautochthonous North Slope crust and a 10- to 15-km-thick section of mantle material. (4) This plate is interpreted as a southward verging tectonic wedge, with its tip in the lower crust or at the Moho beneath the southern Brooks Range. In this interpretation the middle and upper crust, or all of the crust, is detached in the southern Brooks Range by the tectonic wedge, or indentor: as a result, crust is uplifted and deformed above the wedge, and mantle is depressed and underthrust beneath this wedge. (5) Underthrusting has juxtaposed mantle of two different origins (and seismic velocities), giving rise to a prominent sub-Moho reflector. Copyright 1997 by the American Geophysical Union.

Pleistocene to Holocene contrasts in organic matter production and preservation on the California continental margin

USGS Publications Warehouse

Dean, W.E.; Gardner, J.V.

1998-01-01

Organic matter in sediments from cores collected from the upper continental slope (200-2700 m) off California and southern Oregon shows marked differences in concentration and marine character between the last glacial interval (ca. 24-10 ka) and either Holocene time or last interstadial (oxygen isotope stage 3, ca. 60-24 ka). In general, sediments deposited during Holocene time and stage 3 contain higher amounts of marine organic matter than those deposited during the last glacial interval, and this contrast is greatest in cores collected off southern California. The most profound differences in stage 3 sediments are between predominantly bioturbated sediments and occasional interbeds of laminated sediments. The sediments are from cores collected within the present oxygen minimum zone on the upper continental slope from as far north as the Oregon-California border to as far south as Point Conception. These upper Pleistocene laminated sediments contain more abundant hydrogen-rich (type II) marine algal organic matter than even surface sediments that have large amounts of nonrefractory organic matter. The stable carbon-isotopic composition of the organic matter does not change with time between bioturbated and laminated sediments, indicating that the greater abundance of type II organic matter in the laminated sediments is not due to a change in source but rather represents a greater degree of production and preservation of marine organic matter. The presence of abundant, well-preserved organic matter supports the theory that the oxygen minimum zone in the northeastern Pacific Ocean was more intense, and possibly anoxic, during late Pleistocene time as a result of increased coastal upwelling that enhanced algal productivity.

Provenance and depositional history of continental slope sediments in the Southwestern Gulf of Mexico unraveled by geochemical analysis

NASA Astrophysics Data System (ADS)

Armstrong-Altrin, John S.; Machain-Castillo, María Luisa; Rosales-Hoz, Leticia; Carranza-Edwards, Arturo; Sanchez-Cabeza, Joan-Albert; Ruíz-Fernández, Ana Carolina

2015-03-01

The aim of this work is to constrain the provenance and depositional history of continental slope sediments in the Southwestern Gulf of Mexico (~1089-1785 m water depth). To achieve this, 10 piston sediment cores (~5-5.5 m long) were studied for mineralogy, major, trace and rare earth element geochemistry. Samples were analyzed at three core sections, i.e. upper (0-1 cm), middle (30-31 cm) and lower (~300-391 cm). The textural study reveals that the core sediments are characterized by silt and clay fractions. Radiocarbon dating of sediments for the cores at different levels indicated a maximum of ~28,000 year BP. Sediments were classified as shale. The chemical index of alteration (CIA) values for the upper, middle, and lower sections revealed moderate weathering in the source region. The index of chemical maturity (ICV) and SiO2/Al2O3 ratio indicated low compositional maturity for the core sediments. A statistically significant correlation observed between total rare earth elements (∑REE) versus Al2O3 and Zr indicated that REE are mainly housed in detrital minerals. The North American Shale Composite (NASC) normalized REE patterns, trace element concentrations such as Cr, Ni and V, and the comparison of REE concentrations in sediments and source rocks indicated that the study area received sediments from rocks intermediate between felsic and mafic composition. The enrichment factor (EF) results indicated that the Cd and Zn contents of the upper section sediments were influenced by an anthropogenic source. The trace element ratios and authigenic U content of the core sediments indicated the existence of an oxic depositional environment.

Influence of the Geometry Alteration of the Landslide Slope on its Stability: A Case Study in the Carnian Alps (Italy)

NASA Astrophysics Data System (ADS)

Zabuski, Lesław; Bossi, Giulia; Marcato, Gianluca

2017-12-01

The paper presents the principles of the slope reprofiling and proves the effectiveness of this stabilization measure. The case study of two adjacent landslides in the National Road 52 "Carnica" in the Tagliamento River valley, the Carnian Alps (46°23'49″N, 12°42'51″E) are the example allowing for illustration of this approach. The phenomena have been studied for more than a decade, making it possible to carry out a detailed geological and geomorphological reconstruction. That was done on the basis of a large amount of monitoring data collected during that period. Since the landslides are threatening an important road, countermeasure works to ameliorate the stability conditions of the slides need to be designed. The paper focuses on the creation of a numerical model consistent with monitoring data and capable of reconstructing the dynamics of both landslides. Two cross-sections, one for each landslide, were selected for the analysis. The geometry of the slip surface was determined on the basis of control points, such as slip surface readings from inclinometers, and geomorphological evidence for the contour. The FLAC2D code was used to evaluate the current stability of these landslides and to determine the effectiveness of changing the slope geometry by removing material from the upper part of the slope and putting it to the lowest part as reinforcement.

Spatial distribution of Qinghai spruce forests and the thresholds of influencing factors in a small catchment, Qilian Mountains, northwest China.

PubMed

Yang, Wenjuan; Wang, Yanhui; Wang, Shunli; Webb, Ashley A; Yu, Pengtao; Liu, Xiande; Zhang, Xuelong

2017-07-17

Forest restoration in dryland mountainous areas is extremely difficult due to dry climate, complex topography and accelerating climate change. Thus, exact identification of suitable sites is required. This study at a small watershed of Qilian Mountains, Northwest China, aimed to determine the important factors and their thresholds limiting the spatial distribution of forests of Qinghai spruce (Picea crassifolia), a locally dominant tree species. The watershed was divided into 342 spatial units. Their location, terrain and vegetation characteristics were recorded. Statistical analysis showed that the potential distribution area of Qinghai spruce forests is within an ellipse with the axes of elevation (from 2673.6 to 3202.2 m a.s.l.) and slope aspect (from -162.1° to 75.1° deviated from North). Within this ellipse, the forested sites have a soil thickness ≥40 cm, and slope positions of lower-slope, lower- or middle-slope, anywhere if the elevation is <2800, 2800-2900, >2900 m a.s.l, respectively. The corresponding mean annual air temperature at upper elevation boundary is -2.69 °C, while the mean annual precipitation at lower elevation boundary is 374 (331) mm within the small watershed (study area). The high prediction accuracy using these 4 factors can help to identify suitable sites and increase the success of afforestation.

Strength and fatigability of selected muscles in upper limb: assessing muscle imbalance relevant to tennis elbow.

PubMed

Alizadehkhaiyat, O; Fisher, A C; Kemp, G J; Frostick, S P

2007-08-01

The aetiology of tennis elbow has remained uncertain for more than a century. To examine muscle imbalance as a possible pathophysiological factor requires a reliable method of assessment. This paper describes the development of such a method and its performance in healthy subjects. We propose a combination of surface and fine-wire EMG of shoulder and forearm muscles and wrist strength measurements as a reliable tool for assessing muscle imbalance relevant to the pathophysiology of tennis elbow. Six healthy volunteers participated. EMG data were acquired at 50% maximal voluntary isometric contraction from five forearm muscles during grip and three shoulder muscles during external rotation and abduction, and analysed using normalized median frequency slope as a fatigue index. Wrist extension/flexion strength was measured using a purpose-built dynamometer. Significant negative slope of median frequency was found for all muscles, with good reproducibility, and no significant difference in slope between the different muscles of the shoulder and the wrist. (Amplitude slope showed high variability and was therefore unsuitable for this purpose.) Wrist flexion was 27+/-8% stronger than extension (mean+/-SEM, p=0.006). This is a reliable method for measuring muscle fatigue in forearm and shoulder. EMG and wrist strength studies together can be used for assessing and identifying the muscle balance in the wrist-forearm-shoulder chain.

Modeling hydrological controls on vegetation distribution across topography in Seward Peninsula, Alaska

NASA Astrophysics Data System (ADS)

Mekonnen, Z. A.; Riley, W. J.; Grant, R. F.; Salmon, V. G.; Iversen, C. M.; Biraud, S.; Breen, A. L.

2017-12-01

Observed changes in vegetation affect carbon and nutrient cycles in diverse landscapes of northern ecosystems. These changes can be affected by topography and landscape hydrology. We applied a coupled transect version of the ecosystem model ecosys in a landscape underlain by impermeable permafrost at Kougarok, Alaska to examine hydrological controls on watershed-scale vegetation distributions. Our preliminary results indicate strong relationships between vegetation distribution and soil physical and hydraulic properties that control water, nutrients, and energy flows across the hillslope. Modeled differences in aboveground biomass across the Kougarok hillslope had a good agreement (R2 0.80) with preliminary biomass measurements from the NGEE-Arctic project in summer 2016. Low soil water content from shallower soil depth and lateral flow of water and nutrients in the upper slope position of the hillslope resulted in water stress and low N mineralization for plants with deeper roots. The middle slope position had intermediate soil moisture from deeper soil and higher N mineralization that favoured fast-growing and deep-rooted plants. The gentle slope and deeper soil in the lower slope position resulted in saturated soil, thus reduced O2 for microbes, hence favouring plants with higher root porosity. Earth system models that do not account for the underlying mechanisms of surface and sub-surface flows of water, nutrients, and energy may not predict these types of dynamics in Arctic ecosystems.

Hanging canyons of Haida Gwaii, British Columbia, Canada: Fault-control on submarine canyon geomorphology along active continental margins

NASA Astrophysics Data System (ADS)

Harris, Peter T.; Barrie, J. Vaughn; Conway, Kim W.; Greene, H. Gary

2014-06-01

Faulting commonly influences the geomorphology of submarine canyons that occur on active continental margins. Here, we examine the geomorphology of canyons located on the continental margin off Haida Gwaii, British Columbia, that are truncated on the mid-slope (1200-1400 m water depth) by the Queen Charlotte Fault Zone (QCFZ). The QCFZ is an oblique strike-slip fault zone that has rates of lateral motion of around 50-60 mm/yr and a small convergent component equal to about 3 mm/yr. Slow subduction along the Cascadia Subduction Zone has accreted a prism of marine sediment against the lower slope (1500-3500 m water depth), forming the Queen Charlotte Terrace, which blocks the mouths of submarine canyons formed on the upper slope (200-1400 m water depth). Consequently, canyons along this margin are short (4-8 km in length), closely spaced (around 800 m), and terminate uniformly along the 1400 m isobath, coinciding with the primary fault trend of the QCFZ. Vertical displacement along the fault has resulted in hanging canyons occurring locally. The Haida Gwaii canyons are compared and contrasted with the Sur Canyon system, located to the south of Monterey Bay, California, on a transform margin, which is not blocked by any accretionary prism, and where canyons thus extend to 4000 m depth, across the full breadth of the slope.

Offshore geology and geomorphology from Point Piedras Blancas to Pismo Beach, San Luis Obispo County, California

USGS Publications Warehouse

Watt, Janet Tilden; Johnson, Samuel Y.; Hartwell, Stephen R.; Roberts, Michelle

2015-01-01

Sea level was approximately 120 to 130 m lower during the Last Glacial Maximum (about 21 ka). This approximate depth corresponds to the modern shelf break, a lateral change from the gently dipping (0.8° to 1.0°) outer shelf to the slightly more steeply dipping (about 1.5° to 2.5°) upper slope in the central and northern parts of the map area. South of Point San Luis in San Luis Bay, deltaic deposits offshore of the mouth of the Santa Maria River (11 km south of the map area) have prograded across the shelf break and now form a continuous low-angle (about 0.8°) ramp that extends to water depths of more than 160 m. The shelf break defines the landward boundary of slope deposits. North of Estero Bay, the shelf break is characterized by a distinctly sharp slope break that is mapped as a landslide headscarp above landslide deposits. Multibeam imagery and seismic-reflection profiles across this part of the shelf break show evidence of slope failure, such as slumping, sliding, and soft-sediment deformation, along the entire length of the scarp. Notably, this shelf-break scarp corresponds to a west splay of the Hosgri Fault that dies out just north of the scarp, suggesting that faulting is controlling the location (and instability) of the shelf break in this area.

How and when human chorionic gonadotropin curves in women with an ectopic pregnancy mimic other outcomes: differences by race and ethnicity.

PubMed

Dillon, Katherine E; Sioulas, Vasileios D; Sammel, Mary D; Chung, Karine; Takacs, Peter; Shaunik, Alka; Barnhart, Kurt T

2012-10-01

To investigate the hCG profiles in a diverse patient group with ectopic pregnancy (EP) and to understand when they may mimic the curves of an intrauterine pregnancy (IUP) or spontaneous abortion (SAB). Retrospective cohort study. Three university hospitals. One hundred seventy-nine women with symptomatic pregnancy of unknown location. None. Slope of log hCG; days and visits to final diagnosis. Of women with an EP, 60% initially exhibited an increase in hCG values, with a median slope of 32% increase in 2 days; 40% of subjects initially had an hCG decrease, with the median slope calculated as a 15% decline in 2 days. In total, the hCG curves in 27% of women diagnosed with EP resembled that of a growing IUP or SAB. Of the EP hCG curves, 16% demonstrated a change in the direction of the slope of the curve. This was more common in African Americans and less evident in Hispanics. Furthermore, it was associated with more clinical visits and days until final diagnosis. The rate of change in serial hCG values can be used to distinguish EP from an IUP or SAB in only 73% of cases. The number of women who had a change in direction of serial hCG values was associated with race and ethnicity. Copyright © 2012 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Deep-sea suprabenthos assemblages (Crustacea) off the Balearic Islands (western Mediterranean): Mesoscale variability in diversity and production

NASA Astrophysics Data System (ADS)

Cartes, J. E.; Mamouridis, V.; Fanelli, E.

2011-04-01

The composition of suprabenthic crustacean assemblages, their diversity, production (P) and production/biomass (P/B) ratios, were analyzed at species level along two transects situated to the north (N) and south (S) of Mallorca (Balearic Islands, western Mediterranean) at depths between 134 m and 760 m, based on a ca. bi-monthly sampling performed between August 2003 and June 2004. Differences with depth and season in assemblage composition and diversity were analyzed as a function of the contrasting environmental features (e.g. water mass dynamics) of the two areas. We identified 187 species (18 decapods, 5 euphausiids, 16 mysids, 76 gammaridean amphipods, 13 hyperiids, 1 caprellid, 21 isopods and 37 cumaceans). Substantial mesoscale variability in the deep-sea suprabenthic assemblages coupled with diversity trends between the N and S transects were found. Seasonality was the most important gradient influencing the dynamics of suprabenthos over the upper (350 m) and middle (650-750 m) slope in the N area. Conversely, the S area appeared to be more stable temporally with depth as the main gradient inducing assemblage differences. Different depth-related patterns were observed both for diversity and P/B. To the north diversity was very low at the shelf-break, increasing on the upper-slope ( H' > 3.00) and then decreasing again on the middle-slope. To the south diversity increased smoothly downward, reaching the highest values on the middle-slope. Regarding productivity, P/B was highest at intermediate depths to the north (over ca. 450-500 m), while to the south highest P/Bs were found deeper (over ca. 600-650 m). The higher P/B at intermediate depths found along N are likely due to higher % of organic matter (OM) in sediments, a product of oceanographic frontal systems. In particular, P/B was higher along N among omnivores and detritus feeders (e.g. Andaniexis mimonectes, Lepechinella manco and combined cumaceans), coupled to enriched OM in sediments, while along S mesoplanktonic carnivores ( Rhachotropis spp.) had higher P/Bs. We conclude that on the north slope the influence of frontal systems and more active flow dynamics of different water masses (WIW and LIW) increases natural disturbance in the area, increasing productivity and diversity of suprabenthic peracarids in the Benthic Boundary Layer. Also, species showed a displacement of their average distributions (their Centres of Gravity, CoG) to shallower depths along N, which is another indicator of more favorable habitat conditions for suprabenthos in the 400-500 m range at N.

Depth of Small Scale Landslide in Slate Area : Case of 2009 Typhoon Morakot in Ai-Liao River, South Taiwan

NASA Astrophysics Data System (ADS)

Chen, T. C.; Yen, H. Y.; Zhou, F. L.

2015-12-01

This study focuses on the depth and magnitude of the small scale landslide in slate area in Ai-Liao-Shi catchment, South Taiwan. Landslide inventory of 2009 Typhoon Morakot, 5×5 m DEM, and aero photo have been interpreted by GIS software to assess the slope type and the scale of landslide events. The research database includes 276 landslides which orthographic projection areas are smaller than 1 ha. The slopes were also classified into dip, orthoclinical-dip, escarpment, and orthoclinical- escarpment 4 types of slope based on the slope aspect to the bedding orientation. The sliding plane, or so call the failure plane, was identified by aero photo, field reconnaissance and verification, and DEM before and after the typhoon event. Colluvium material deposited on the slip plane was removed based on the scarp and foot position, mass movement pattern, weak plane orientation, and the micro topography of a landslide to achieve the reasonable sliding plane. The maximum depth of sliding surface is explored through the slope type and sliding plane in total of 276 landslide cases. Results demonstrate that the average maximum depth, Dam, of dip slope is 4.6 m, Dam of orthoclinical-dip, escarpment, and orthoclinical-escarpment slopes are 5.8, 6.0, and 6.3 m respectively. In general, Dam is creasing with the average slope of landslide, the relationship of both factor is achieved in the study. Meanwhile, the orthographic projection area of landslide is increasing with the slope angle till the angle up to 40 degree then decreasing. The depth also varies with landslide magnitude. Finally, the relation of the depth normal to slope surface and the depth in gravity direction of landslides in four types slope are proposed, the R square values are 0.862 to 0.891 showing a good correlation between two types of depth.

Geometry and significance of stacked gullies on the northern California slope

USGS Publications Warehouse

Field, M.E.; Gardner, J.V.; Prior, D.B.

1999-01-01

Recent geophysical surveys off northern California reveal patterns of gullies on the sea floor and preserved within continental-slope deposits that represent both erosional and aggradational processes. These surveys, conducted as part of the STRATAFORM project, combined multibeam bathymetry and backscatter with high-resolution seismic profiles. These data provide a new basis for evaluating gully morphology, distribution, and their significance to slope sedimentation and evolution. The continental margin off northern California exhibits an upper slope that has undergone both progradation and aggradation. The slope surface, which dips at <2??to 4.0??, contains a set of straight, evenly spaced, and parallel to sub-parallel gullies that begin at the 380-m isobath and extend onto the Eel and Klamath plateaus and into Trinity Canyon. The surface gullies are typically 100-m wide or more and only 1-2 m deep. The gullied slope is underlain by a sedimentary sequence that contains abundant buried gullies to subsurface depths of over 150 m. Although some of the buried gullies are distinctly erosional, most are part of the aggradational pattern responsible for the overall growth of the slope. The latest phase of gully erosion is marked by a gullied surface lying <20 m below the present-day sea floor. These erosional gullies locally truncate individual reflectors, have small depositional levees, and exhibit greater relief than do overlying gullies exposed on the sea floor. The older subsurface gullies document a period of widespread, but minor, erosion and downslope transport, presumably from a large, proximal sediment source. The cycles of downcutting and gully excavation are a minor part of the stratigraphic section, and are likely related to the combined influence of lower sea levels and higher sediment yields. During aggradation of the slope depositional sequences, sediment was draped over the gully features, producing sediment layers that mimic the underlying gully form. Consequently, gully morphology and geometries were preserved and migrated upwards with time. The processes that produce aggraded gully drape also resulted in laterally continuous strata and were most likely related to a period when the sediment source was dispersed from a more distal (10s of km) source, such as during present conditions. The draped sequences also contain a few new gullies, which indicates that gullies can be initiated at all or most stages of slope growth.

Linking interannual variability in shelf bottom water properties to the California Undercurrent and local processes in the Pacific Northwest

NASA Astrophysics Data System (ADS)

Stone, H. B.; Banas, N. S.; Hickey, B. M.; MacCready, P.

2016-02-01

The Pacific Northwest coast is an unusually productive area with a strong river influence and highly variable upwelling-favorable and downwelling-favorable winds, but recent trends in hypoxia and ocean acidification in this region are troubling to both scientists and the general public. A new ROMS hindcast model of this region makes possible a study of interannual variability. This study of the interannual temperature and salinity variability on the Pacific Northwest coast is conducted using a coastal hindcast model (43°N - 50°N) spanning 2002-2009 from the University of Washington Coastal Modeling Group, with a resolution of 1.5 km over the shelf and slope. Analysis of hindcast model results was used to assess the relative importance of source water variability, including the poleward California Undercurrent, local and remote wind forcing, winter wind-driven mixing, and river influence in explaining the interannual variations in the shelf bottom layer (40 - 80 m depth, 10 m thick) and over the slope (150 - 250 m depth, <100 km from shelf break) at each latitude within the model domain. Characterized through tracking of the fraction of Pacific Equatorial Water (PEW) relative to Pacific Subarctic Upper Water (PSUW) present on the slope, slope water properties at all latitudes varied little throughout the time series, with the largest variability due to patterns of large north-south advection of water masses over the slope. Over the time series, the standard deviation of slope temperature was 0.09 ˚C, while slope salinity standard deviation was 0.02 psu. Results suggest that shelf bottom water interannual variability is not driven primarily by interannual variability in slope water as shelf bottom water temperature and salinity vary nearly 10 times more than those over the slope. Instead, interannual variability in shelf bottom water properties is likely driven by other processes, such as local and remote wind forcing, and winter wind-driven mixing. The relative contributions of these processes to interannual variability in shelf bottom water properties will be addressed. Overall, these results highlight the importance of shelf processes relative to large-scale influences on the interannual timescale in particular. Implications for variability in hypoxia and ocean acidification impacts will be discussed.

North Slope (Wahluke Slope) expedited response action cleanup plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of this action is to mitigate any threat to public health and the environment from hazards on the North Slope and meet the expedited response action (ERA) objective of cleanup to a degree requiring no further action. The ERA may be the final remediation of the 100-I-3 Operable Unit. A No Action record of decision (ROD) may be issued after remediation completion. The US Department of Energy (DOE) currently owns or administers approximately 140 mi{sup 2} (about 90,000 acres) of land north and east of the Columbia River (referred to as the North Slope) that is part ofmore » the Hanford Site. The North Slope, also commonly known as the Wahluke Slope, was not used for plutonium production or support facilities; it was used for military air defense of the Hanford Site and vicinity. The North Slope contained seven antiaircraft gun emplacements and three Nike-Ajax missile positions. These military positions were vacated in 1960--1961 as the defense requirements at Hanford changed. They were demolished in 1974. Prior to government control in 1943, the North Slope was homesteaded. Since the initiation of this ERA in the summer of 1992, DOE signed the modified Hanford Federal Agreement and Consent Order (Tri-Party Agreement) with the Washington Department of Ecology (Ecology) and the US Environmental Protection Agency (EPA), in which a milestone was set to complete remediation activities and a draft closeout report by October 1994. Remediation activities will make the North Slope area available for future non-DOE uses. Thirty-nine sites have undergone limited characterization to determine if significant environmental hazards exist. This plan documents the results of that characterization and evaluates the potential remediation alternatives.« less

A new upper bound for the norm of interval matrices with application to robust stability analysis of delayed neural networks.

PubMed

Faydasicok, Ozlem; Arik, Sabri

2013-08-01

The main problem with the analysis of robust stability of neural networks is to find the upper bound norm for the intervalized interconnection matrices of neural networks. In the previous literature, the major three upper bound norms for the intervalized interconnection matrices have been reported and they have been successfully applied to derive new sufficient conditions for robust stability of delayed neural networks. One of the main contributions of this paper will be the derivation of a new upper bound for the norm of the intervalized interconnection matrices of neural networks. Then, by exploiting this new upper bound norm of interval matrices and using stability theory of Lyapunov functionals and the theory of homomorphic mapping, we will obtain new sufficient conditions for the existence, uniqueness and global asymptotic stability of the equilibrium point for the class of neural networks with discrete time delays under parameter uncertainties and with respect to continuous and slope-bounded activation functions. The results obtained in this paper will be shown to be new and they can be considered alternative results to previously published corresponding results. We also give some illustrative and comparative numerical examples to demonstrate the effectiveness and applicability of the proposed robust stability condition. Copyright © 2013 Elsevier Ltd. All rights reserved.

Perturbation of seafloor bacterial community structure by drilling waste discharge.

PubMed

Nguyen, Tan T; Cochrane, Sabine K J; Landfald, Bjarne

2018-04-01

Offshore drilling operations result in the generation of drill cuttings and localized smothering of the benthic habitats. This study explores bacterial community changes in the in the upper layers of the seafloor resulting from an exploratory drilling operation at 1400m water depth on the Barents Sea continental slope. Significant restructurings of the sediment microbiota were restricted to the sampling sites notably affected by the drilling waste discharge, i.e. at 30m and 50m distances from the drilling location, and to the upper 2cm of the seafloor. Three bacterial groups, the orders Clostridiales and Desulfuromonadales and the class Mollicutes, were almost exclusively confined to the upper two centimeters at 30m distance, thereby corroborating an observed increase in anaerobicity inflicted by the drilling waste deposition. The potential of these phylogenetic groups as microbial bioindicators of the spatial extent and persistence of drilling waste discharge should be further explored. Copyright © 2017 Elsevier Ltd. All rights reserved.

30 CFR 817.102 - Backfilling and grading: General requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... terrain if the following requirements are met: (1) All vegetative and organic material shall be removed... to conserve soil moisture, ensure stability, and control erosion on final-graded slopes, if the...

30 CFR 817.102 - Backfilling and grading: General requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... terrain if the following requirements are met: (1) All vegetative and organic material shall be removed... to conserve soil moisture, ensure stability, and control erosion on final-graded slopes, if the...

30 CFR 817.102 - Backfilling and grading: General requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... terrain if the following requirements are met: (1) All vegetative and organic material shall be removed... to conserve soil moisture, ensure stability, and control erosion on final-graded slopes, if the...

30 CFR 817.102 - Backfilling and grading: General requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... terrain if the following requirements are met: (1) All vegetative and organic material shall be removed... to conserve soil moisture, ensure stability, and control erosion on final-graded slopes, if the...

30 CFR 817.102 - Backfilling and grading: General requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... terrain if the following requirements are met: (1) All vegetative and organic material shall be removed... to conserve soil moisture, ensure stability, and control erosion on final-graded slopes, if the...

A hazard and risk classification system for catastrophic rock slope failures in Norway

NASA Astrophysics Data System (ADS)

Hermanns, R.; Oppikofer, T.; Anda, E.; Blikra, L. H.; Böhme, M.; Bunkholt, H.; Dahle, H.; Devoli, G.; Eikenæs, O.; Fischer, L.; Harbitz, C. B.; Jaboyedoff, M.; Loew, S.; Yugsi Molina, F. X.

2012-04-01

The Geological Survey of Norway carries out systematic geologic mapping of potentially unstable rock slopes in Norway that can cause a catastrophic failure. As catastrophic failure we describe failures that involve substantial fragmentation of the rock mass during run-out and that impact an area larger than that of a rock fall (shadow angle of ca. 28-32° for rock falls). This includes therefore rock slope failures that lead to secondary effects, such as a displacement wave when impacting a water body or damming of a narrow valley. Our systematic mapping revealed more than 280 rock slopes with significant postglacial deformation, which might represent localities of large future rock slope failures. This large number necessitates prioritization of follow-up activities, such as more detailed investigations, periodic monitoring and permanent monitoring and early-warning. In the past hazard and risk were assessed qualitatively for some sites, however, in order to compare sites so that political and financial decisions can be taken, it was necessary to develop a quantitative hazard and risk classification system. A preliminary classification system was presented and discussed with an expert group of Norwegian and international experts and afterwards adapted following their recommendations. This contribution presents the concept of this final hazard and risk classification that should be used in Norway in the upcoming years. Historical experience and possible future rockslide scenarios in Norway indicate that hazard assessment of large rock slope failures must be scenario-based, because intensity of deformation and present displacement rates, as well as the geological structures activated by the sliding rock mass can vary significantly on a given slope. In addition, for each scenario the run-out of the rock mass has to be evaluated. This includes the secondary effects such as generation of displacement waves or landslide damming of valleys with the potential of later outburst floods. It became obvious that large rock slope failures cannot be evaluated on a slope scale with frequency analyses of historical and prehistorical events only, as multiple rockslides have occurred within one century on a single slope that prior to the recent failures had been inactive for several thousand years. In addition, a systematic analysis on temporal distribution indicates that rockslide activity following deglaciation after the Last Glacial Maximum has been much higher than throughout the Holocene. Therefore the classification system has to be based primarily on the geological conditions on the deforming slope and on the deformation rates and only to a lesser weight on a frequency analyses. Our hazard classification therefore is primarily based on several criteria: 1) Development of the back-scarp, 2) development of the lateral release surfaces, 3) development of the potential basal sliding surface, 4) morphologic expression of the basal sliding surface, 5) kinematic feasibility tests for different displacement mechanisms, 6) landslide displacement rates, 7) change of displacement rates (acceleration), 8) increase of rockfall activity on the unstable rock slope, 9) Presence post-glacial events of similar size along the affected slope and its vicinity. For each of these criteria several conditions are possible to choose from (e.g. different velocity classes for the displacement rate criterion). A score is assigned to each condition and the sum of all scores gives the total susceptibility score. Since many of these observations are somewhat uncertain, the classification system is organized in a decision tree where probabilities can be assigned to each condition. All possibilities in the decision tree are computed and the individual probabilities giving the same total score are summed. Basic statistics show the minimum and maximum total scores of a scenario, as well as the mean and modal value. The final output is a cumulative frequency distribution of the susceptibility scores that can be divided into several classes, which are interpreted as susceptibility classes (very high, high, medium, low, and very low). Today the Norwegian Planning and Building Act uses hazard classes with annual probabilities of impact on buildings producing damages (<1/100, <1/1000, <1/5000 and zero for critical buildings). However, up to now there is not enough scientific knowledge to predict large rock slope failures in these strict classes. Therefore, the susceptibility classes will be matched with the hazard classes from the Norwegian Building Act (e.g. very high susceptibility represents the hazard class with annual probability >1/100). The risk analysis focuses on the potential fatalities of a worst case rock slide scenario and its secondary effects only and is done in consequence classes with a decimal logarithmic scale. However we recommend for all high risk objects that municipalities carry out detailed risk analyses. Finally, the hazard and risk classification system will give recommendations where surveillance in form of continuous 24/7 monitoring systems coupled with early-warning systems (high risk class) or periodic monitoring (medium risk class) should be carried out. These measures are understood as to reduce the risk of life loss due to a rock slope failure close to 0 as population can be evacuated on time if a change of stability situation occurs. The final hazard and risk classification for all potentially unstable rock slopes in Norway, including all data used for its classification will be published within the national landslide database (available on www.skrednett.no).

2D transient granular flows over obstacles: experimental and numerical work

NASA Astrophysics Data System (ADS)

Juez, Carmelo; Caviedes-Voullième, Daniel; Murillo, Javier; García-Navarro, Pilar

2016-04-01

Landslides are an ubiquitous natural hazard, and therefore human infrastructure and settlements are often at risk in mountainous regions. In order to better understand and predict landslides, systematic studies of the phenomena need to be undertaken. In particular, computational tools which allow for analysis of field problems require to be thoroughly tested, calibrated and validated under controlled conditions. And to do so, it is necessary for such controlled experiments to be fully characterized in the same terms as the numerical model requires. This work presents an experimental study of dry granular flow over a rough bed with topography which resembles a mountain valley. It has an upper region with a very high slope. The geometry of the bed describes a fourth order polynomial curve, with a low point with zero slope, and afterwards a short region with adverse slope. Obstacles are present in the lower regions which are used as model geometries of human structures. The experiments consisted of a sudden release a mass of sand on the upper region, and allowing it to flow downslope. Furthermore, it has been frequent in previous studies to measure final states of the granular mass at rest, but seldom has transient data being provided, and never for the entire field. In this work we present transient measurements of the moving granular surfaces, obtained with a consumer-grade RGB-D sensor. The sensor, developed for the videogame industry, allows to measure the moving surface of the sand, thus obtaining elevation fields. The experimental results are very consistent and repeatable. The measured surfaces clearly show the distinctive features of the granular flow around the obstacles and allow to qualitatively describe the different flow patterns. More importantly, the quantitative description of the granular surface allows for benchmarking and calibration of predictive numerical models, key in scaling the small-scale experimental knowledge into the field. In addition, as the material is traditionally oriented in a predominant longitudinal direction and the layer of the mass is thin in comparison to the scale of interest, the depth-averaged procedure can be performed in the mass and momentum equations. Regarding the friction theory embedded in the landslide motion, a Coulomb-like basal friction law can be assumed as a first attempt of reproducing the phenomena. On the other hand, the presence of obstacles, involves the study of the development of schock waves imposing the simulation of the granular behavior by means of a schock-tracking numerical scheme. The numerical scheme employed, is based on an approximate solvers based on Roe approaches, devoting especial attention to the frictional source terms. This work was partially funded by the ITN-Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme FP7-PEOPLE-2013-ITN under REA grant agreement n_607394-SEDITRANS. The granular experiments were funded by DGA, Diputación General de Aragón, España.

The Schistes à Blocs Fm: the ultimate member of the Annot Sandstones in the Southern Alps (France); slope gullies or canyon system?

NASA Astrophysics Data System (ADS)

Rubino, Jean-Loup; Mercier, Louison; Daghdevirenian, Laurent; Migeon, Sébastien; Bousquet, Romain; Broucke, Olivier; Raisson, Francois; Joseph, Philippe; Deschamp, Remi; Imbert, Patrice

2017-04-01

Described since a long time, the Schistes à Blocs Fm is the ultimate member of the famous tertiary Grès d'Annot Sandstones in southern alpine foredeep basin in SE France. It mainly consists of shales, silty shales, debris flows, olistoliths and a subordinate amount of sandstones. Since their introduction, and because of their location down to major thrust sheet, they have been considered as a tectono-sedimentary unit linked to the nappe's emplacement and refer as an olistostrome, (Kerckove 1964-1969). However they are separated from the underlying Annot Sandstones by a major erosional surface which deeply cuts, up to 500m, into the sandy turbidites; this surface definitively predates the infill and the nappe emplacement. This is supported by the fact that imbricates affect the upper part of the Schistes and also because of the age; the Schistes à Blocs being Upper Eocene to Lower Oligocene whilst the nappe is latest Oligocene to Lower Miocene. A detailed analysis of the erosional surface in la Bonette area reveals a complex geometry which shows obvious similarities with these observed either on submarine canyons or in slope dissected by gullies as shown by numerous seabeams or 3D seismic images. The infill is quite complex, no basal lag have been observed, however bioturbations suggest occurrence of by pass. Most commonly the lower part of the infill is made of muddy or silty sediments. In some areas, decametric to pluri hectometric olistoliths are interbedded within these deposits. Debris flows are also common with a muddy matrix and finally isolated turbidite channels including the same material than in the Annot Sandstones occur. The reworked material into the debris flows and in the olistoliths suggests that it doesn't only derived from canyon flanks (sandstones) but includes elements belonging to older tethyan series such as Triassic and Liassic carbonates which must be exposed on the sea floor on local highs in the more internal part of the Alps but much earlier than the nappe emplacement. In the forthcoming weeks, thanks to an already done drone acquisition of the cliffs, a 3D gridded model will be realize and will allow to discriminate if we are dealing with a major canyon with lateral irregularities or if, all incisions must be interpreted as numerous gullies entrenching the slope, it will also help to restore the offset of small normal faults affecting the surface. Such type of features are of primary importance in the deep sea sediment routine system; very few examples of mud filled prone canyon are published and because of the outcrop quality, this example can become a world class analog; particularly to highlight potential hydrocarbon trapping mechanism in turbidite systems. Many other outcrops, of a coeval Fm occur all along the Alps from Italy to Switzerland and can provide opportunities to analyze variation of geometrical elements and describe additional facies participating to the infill.

High-resolution bathymetry and acoustic geophysical data from Santa Maria di Leuca Cold Water Coral province (Northern Ionian Sea—Apulian continental slope)

NASA Astrophysics Data System (ADS)

Savini, A.; Corselli, C.

2010-03-01

A total of 800 km 2 of multibeam echo-sounder coverage, roughly 800 km of chirp-sonar data and 18 km of side-scan sonar profiles (100/500 kHz) were acquired a few km offshore Santa Maria di Leuca (south-eastern Italy), from 200 m to 1300 m water depth. The explored area belongs to the upper slope of the gently south-eastward dipping Apulian continental margin (northern Ionian Sea). Acoustic datasets were collected, by three different oceanographic expeditions, where evidence of living cold-water coral (CWC) colonies were documented by previous surveys and samples. High-resolution multibeam bathymetry indicated an extensive rough seafloor with an irregular faulted upper surface to the west (reflecting large-scale tectonic control on the margin) and a highly disrupted upper slope formed by prominent downslope mass-movements to the north. A broad area in the east was influenced by mass-transport deposition, which resulted in a very complex hummocky seafloor, mainly shaped by detached block-like features and failure-related bedforms (i.e. low scarps, downslope lineations and compressional ridges). From the shallow seismic-stratigraphic data, failure events appeared to be multiple and recurrent and chaotic reflectors, both buried and exposed at the seafloor, affected most of the investigated area. Drift sedimentation was also recognised along a central large ridge, resulting in an interplay between contour currents and downslope turbidity currents. The spatial distribution of the CWC reefs was inferred from the acoustic facies interpretation based on video images and ground-truthed by sediment samples. It appeared that: (1) within the investigated area, living coral frameworks were located along large topographic highs facing the main flow of the bottom currents, where hard and firm substrata and/or failure-related sediment bedforms occurred; (2) CWC mainly settled on clustered (and isolated) mound-like features, tens to a few hundreds of metres long and no more than 25 m high and were located between 600 and 900 m water depth, within the broad area affected by downslope mass-transport deposits. Such mound-like morphologies could thus be interpreted as a result of sediment accreted by coral growth, with the consequent sediment trapping on small-scale positive seafloor irregularities; formed by different types of Pleistocene-exposed mass-transport deposits, their burial prevented by bottom currents.

Irrigation channels of the Upper Rhone valley (Switzerland). Geomorphological analysis of a cultural heritage

NASA Astrophysics Data System (ADS)

Reynard, Emmanuel

2016-04-01

The Upper Rhone valley (Canton of Valais, Switzerland) is characterised by dry climatic conditions that explain the presence of an important network (about 800 km) of irrigation channels - called Bisses in the French-speaking part of the canton or Suonen in the German-speaking area - dating back to the Middle Ages. This network constitutes a cultural heritage and during the last 30 years these agricultural infrastructures have sparked a renewed interest for tourist and cultural reasons. Indeed, the paths along the channels are used as tourist trails and several abandoned channels have been renovated for tourist use. Based on an inventory of the Bisses/Suonen of Valais, the proposed communication has three aims: (1) to analyse the geomorphological context (morphometric analysis, structural geomorphology, main processes) of various types of channels and to show the impact of the geomorphological context on the building techniques; (2) to identify particularly active processes along the channels; (3) to classify the Bisses/Suonen according to their geomorphological value and to their geomorphological sensitivity, and to propose managing measures. Structural and climatic conditions influence the geomorphological context of the channels. In a structural point of view, irrigation channels are developed in three main contexts: (1) in the Aar Massif crystalline basement; (2) in the limestone and marl cover nappes of the Helvetic Alps; (3) in the metamorphic cover nappes of the Penninic domain. The Rhone River valley is boarded by two high mountain ranges: the Penninic Alps in the South and the Bernese Alps in the North. Because of rain shadow effects, the climate is relatively dry and, between Brig and Martigny, annual rainfall is not more than 600 mm at 500 m ASL and 800 mm at 1600 m ASL. Nevertheless, due to important vertical precipitation gradients annual rainfall totals are high at high altitudes. On the southern facing tributary valleys, the dry climatic conditions are accentuated by high insulation and evaporation. Finally, foehn events are quite common. In a climatic point of view, the area can be divided in three main zones: (1) Upstream of Brig, the climate is characterised by cold and wet conditions, and irrigation is not necessary; (2) between Brig and Martigny, the rain shadow effect is responsible of irrigation needs in the lower altitudes, whereas at high altitudes rainfall is sufficient for plant growing without irrigation; (3) downstream of Martigny, the climate is wetter and irrigation is not necessary. In a palaeoclimatic point of view, the Rhone River catchment was characterised by numerous glaciations during the Quaternary. Quaternary glaciers have shaped the valleys (U-shaped valleys, hanged valleys) and the postglacial hydrographical network had to adapt to the glacial valleys (presence of numerous waterfalls, hanged valleys, postglacial gorges, alluvial fans). By crossing climatic and structural contexts, three groups of geomorphological contexts of irrigation channels can be highlighted: (1) In the tributary valleys situated South of the Rhone valley (Penninic Alps) the irrigation channels are simply dug in the valley slopes; several of them are affected by landslides typical of metamorphic rocks of Penninic Alps; (2) In the short tributary valleys of the crystalline Aar Massif - in the valleys North to the city of Visp -, the geomorphological context is characterised by steep slopes both in the tributary valleys and in the south-facing slopes dominating the Rhone River valley. In this area, water channels are cut into the rocks and in some parts they are built in wood pipes hanged along the rock walls; (3) In the tributary valleys of the Helvetic domain - North of the Rhone River between Leuk and Sion - the geological context highly influences the building techniques: due to geological dipping towards Southeast, the tributary valley are dissymmetric: in the dip slopes channels are simply cut in the soil, whereas in the steep opposite sides, they are hanged on the limestone rock walls. In the south-facing slopes of the main valley, differential erosion by the Rhone glacier has formed a complex alternation of hills, depressions and gently dipping slopes very favourable to agriculture; the irrigation network had adapted to this complex geomorphological context.

Petroleum geology and resources of the middle Caspian Basin, Former Soviet Union

USGS Publications Warehouse

Ulmishek, Gregory F.

2001-01-01

The Middle Caspian basin occupies a large area between the Great Caucasus foldbelt and the southern edge of the Precambrian Russian craton. The basin also includes the central part of the Caspian Sea and the South Mangyshlak subbasin east of the sea. The basin was formed on the Hercynian accreted terrane during Late Permian?Triassic through Quaternary time. Structurally, the basin consists of the fold-and-thrust zone of the northern Caucasus foothills, the foredeep and foreland slope, the Stavropol-Prikumsk uplift and East Manych trough to the north of the slope, and the South Mangyshlak subbasin and slope of the Karabogaz arch east of the Caspian Sea. All these major structures extend offshore. Four total petroleum systems (TPS) have been identified in the basin. The South Mangyshlak TPS contains more than 40 discovered fields. The principal reserves are in Lower?Middle Jurassic sandstone reservoirs in structural traps. Source rocks are poorly known, but geologic data indicate that they are in the Triassic taphrogenic sequence. Migration of oil and gas significantly postdated maturation of source rocks and was related to faulting and fracturing during middle Miocene to present time. A single assessment unit covers the entire TPS. Largest undiscovered resources of this assessment unit are expected in the largely undrilled offshore portion of the TPS, especially on the western plunge of the Mangyshlak meganticline. The Terek-Caspian TPS occupies the fold-and-thrust belt, foredeep, and adjoining foreland slope. About 50 hydrocarbon fields, primarily oil, have been discovered in the TPS. Almost all hydrocarbon reserves are in faulted structural traps related to thrusting of the foldbelt, and most traps are in frontal edges of the thrust sheets. The traps are further complicated by plastic deformation of Upper Jurassic salt and Maykop series (Oligocene? lower Miocene) shale. Principal reservoirs are fractured Upper Cretaceous carbonates and middle Miocene sandstones. Principal source rocks are organic-rich shales in the lower part of the Maykop series. Source rocks may also be present in the Eocene, Upper Jurassic, and Middle Jurassic sections, but their contribution to discovered reserves is probably small. Three assessment units are delineated in the TPS. One of them encompasses the thrust-and-fold belt of northern Caucasus foothills. This assessment unit contains most of the undiscovered oil resources. The second assessment unit occupies the foredeep and largely undeformed foreland slope. Undiscovered resources of this unit are relatively small and primarily related to stratigraphic traps. The third unit is identified in almost untested subsalt Jurassic rocks occurring at great depths and is speculative. The unit may contain significant amounts of gas under the Upper Jurassic salt seal. The Stavropol-Prikumsk TPS lies north of the Terek-Caspian TPS and extends offshore into the central Caspian Sea where geologic data are scarce. More than one hundred oil and gas fields have been found onshore. Offshore, only one well was recently drilled, and this well discovered a large oil and gas field. Almost the entire sedimentary section of the TPS is productive; however, the principal oil reserves are in Lower Cretaceous clastic reservoirs in structural traps of the Prikumsk uplift. Most original gas reserves are in Paleogene reservoirs of the Stavropol arch and these reservoirs are largely depleted. At least three source rock formations, in the Lower Triassic, Middle Jurassic, and Oligocene?lower Miocene (Maykop series), are present in the TPS. Geochemical data are inadequate to correlate oils and gases in most reservoirs with particular source rocks, and widespread mixing of hydrocarbons apparently took place. Three assessment units encompassing the onshore area of the TPS, the offshore continuation of the Prikumsk uplift, and the central Caspian area, are identified. The

The impact of periglacial cover beds on runoff generation in a small spring catchment, Ore Mountains

NASA Astrophysics Data System (ADS)

Heller, Katja; Hübner, Rico; Kleber, Arno

2010-05-01

The knowledge of hillslope processes is essential to improve pollutant research and flood prediction. Relic periglacial covers are widespread on slopes of the central European low mountain ranges. Cover beds are assumed to be an important control factor for subcutaneous water flow paths. Periglacial cover beds originated by solifluction, kryoturbation and accumulation of loess during Pleistocene times. Differences in bulk density, sediment type, as well as structure and rate of coarse clasts in the layers result in vertical disparity in hydraulic conductivity (anisotropy), leading to interflow. This hypothesis has been testing in an ongoing study in a small spring catchment (6 ha) in the eastern Ore Mountains, south-eastern Germany, since November 2007. The study area is underlain by gneiss and is formed as a slope hollow. The cover beds consist of a 3-layer complex with upper layer, intermediate layer and basal layer. Soil water tension within the layers is measured with 76 recording tensiometers. Electrical resistivity tomography was used to monitor the spatial dispersal of soil moisture. Results of hydrometrical measurements and of electrical resistivity surveys will be described and new findings on slope water dynamics will be presented.

Psychometric functions for informational masking

NASA Astrophysics Data System (ADS)

Lutfi, Robert A.; Kistler, Doris J.; Callahan, Michael R.; Wightman, Frederic L.

2003-04-01

The method of constant stimuli was used to obtain complete psychometric functions (PFs) from 44 normal-hearing listeners in conditions known to produce varying amounts of informational masking. The task was to detect a pure-tone signal in the presence of a broadband noise and in the presence of multitone maskers with frequencies and amplitudes that varied at random from one presentation to the next. Relative to the broadband noise condition, significant reductions were observed in both the slope and the upper asymptote of the PF for multitone maskers producing large amounts of informational masking. Slope was affected more for some listeners while asymptote was affected more for others. Mean slopes and asymptotes varied nonmonotonically with the number of masker components in much the same manner as mean thresholds. The results are consistent with a model that assumes trial-by-trial judgments are based on a weighted sum of dB levels at the output of independent auditory filters. For many listeners, however, the weights appear to reflect how often a nonsignal auditory filter is mistaken for the signal filter. For these listeners adaptive procedures may produce a significant bias in the estimates of threshold for conditions of informational masking. [Work supported by NIDCD.

Seasonal electrical resistivity surveys of a coastal bluff, Barter Island, North Slope Alaska

USGS Publications Warehouse

Swarzenski, Peter W.; Johnson, Cordell; Lorenson, Thomas; Conaway, Christopher H.; Gibbs, Ann E.; Erikson, Li; Richmond, Bruce M.; Waldrop, Mark P.

2016-01-01

Select coastal regions of the North Slope of Alaska are experiencing high erosion rates that can be attributed in part to recent warming trends and associated increased storm intensity and frequency. The upper sediment column of the coastal North Slope of Alaska can be described as continuous permafrost underlying a thin (typically less than 1–2 m) active layer that responds variably to seasonal thaw cycles. Assessing the temporal and spatial variability of the active layer and underlying permafrost is essential to better constrain how heightened erosion may impact material fluxes to the atmosphere and the coastal ocean, and how enhanced thaw cycles may impact the stability of the coastal bluffs. In this study, multi-channel electrical resistivity tomography (ERT) was used to image shallow subsurface features of a coastal bluff west of Kaktovik, on Barter Island, northeast Alaska. A comparison of a suite of paired resistivity surveys conducted in early and late summer 2014 provided detailed information on how the active layer and permafrost are impacted during the short Arctic summer. Such results are useful in the development of coastal resilience models that tie together fluvial, terrestrial, climatic, geologic, and oceanographic forcings on shoreline stability.

Crew Earth Observations (CEO) taken during Expedition Five on the ISS

NASA Image and Video Library

2002-08-25

ISS005-E-11189 (25 August 2002) --- Calanscio Sand Sea, Libya is featured in this digital image photographed by an Expedition 5 crewmember on the International Space Station (ISS). A plume of black smoke blowing westward is silhouetted against yellow linear dunes in the great sand sea of northeast Libya. Smoke from flares at remote well heads is commonly seen by astronauts flying over the Sahara Desert. NASA scientists studying the Station imagery had the following observations about the image. The plume dispersal pattern visible at the left edge of the image may be due to upper-level winds or gravitational settling of heavier particulates. The regular pattern of linear dunes is generated by two major winds: the dominant north wind (north is towards the top right) determines the orientation of the sand dunes. Gentler easterly winds, as were blowing when this view was taken, make the dunes asymmetric, with a gentle windward (west) slope and an over steeped downwind slope. Some over steepened slopes even cast shadows in the early morning light. One mound of sand (top right), due north of the well head, does not fit the pattern of linear dunes. This type is known as a star dune.

Impact of sea-level rise on earthquake and landslide triggering offshore the Alentejo margin (SW Iberia)

NASA Astrophysics Data System (ADS)

Neves, M. C.; Roque, C.; Luttrell, K. M.; Vázquez, J. T.; Alonso, B.

2016-12-01

Earthquakes and submarine landslides are recurrent and widespread manifestations of fault activity offshore SW Iberia. The present work tests the effects of sea-level rise on offshore fault systems using Coulomb stress change calculations across the Alentejo margin. Large-scale faults capable of generating large earthquakes and tsunamis in the region, especially NE-SW trending thrusts and WNW-ESE trending dextral strike-slip faults imaged at basement depths, are either blocked or unaffected by flexural effects related to sea-level changes. Large-magnitude earthquakes occurring along these structures may, therefore, be less frequent during periods of sea-level rise. In contrast, sea-level rise promotes shallow fault ruptures within the sedimentary sequence along the continental slope and upper rise within distances of <100 km from the coast. The results suggest that the occurrence of continental slope failures may either increase (if triggered by shallow fault ruptures) or decrease (if triggered by deep fault ruptures) as a result of sea-level rise. Moreover, observations of slope failures affecting the area of the Sines contourite drift highlight the role of sediment properties as preconditioning factors in this region.

Geologic assessment of undiscovered conventional oil and gas resources--Middle Eocene Claiborne Group, United States part of the Gulf of Mexico Basin

USGS Publications Warehouse

Hackley, Paul C.

2012-01-01

The Middle Eocene Claiborne Group was assessed using established U.S. Geological Survey (USGS) assessment methodology for undiscovered conventional hydrocarbon resources as part of the 2007 USGS assessment of Paleogene-Neogene strata of the United States part of the Gulf of Mexico Basin including onshore and State waters. The assessed area is within the Upper Jurassic-Cretaceous-Tertiary Composite total petroleum system, which was defined as part of the assessment. Source rocks for Claiborne oil accumulations are interpreted to be organic-rich downdip shaley facies of the Wilcox Group and the Sparta Sand of the Claiborne Group; gas accumulations may have originated from multiple sources including the Jurassic Smackover and Haynesville Formations and Bossier Shale, the Cretaceous Eagle Ford and Pearsall(?) Formations, and the Paleogene Wilcox Group and Sparta Sand. Hydrocarbon generation in the basin started prior to deposition of Claiborne sediments and is ongoing at present. Emplacement of hydrocarbons into Claiborne reservoirs has occurred primarily via vertical migration along fault systems; long-range lateral migration also may have occurred in some locations. Primary reservoir sands in the Claiborne Group include, from oldest to youngest, the Queen City Sand, Cook Mountain Formation, Sparta Sand, Yegua Formation, and the laterally equivalent Cockfield Formation. Hydrocarbon traps dominantly are rollover anticlines associated with growth faults; salt structures and stratigraphic traps also are important. Sealing lithologies probably are shaley facies within the Claiborne and in the overlying Jackson Group. A geologic model, supported by spatial analysis of petroleum geology data including discovered reservoir depths, thicknesses, temperatures, porosities, permeabilities, and pressures, was used to divide the Claiborne Group into seven assessment units (AU) with distinctive structural and depositional settings. The AUs include (1) Lower Claiborne Stable Shelf Gas and Oil (50470120), (2) Lower Claiborne Expanded Fault Zone Gas (50470121), (3) Lower Claiborne Slope and Basin Floor Gas (50470122), (4) Lower Claiborne Cane River (50470123), (5) Upper Claiborne Stable Shelf Gas and Oil (50470124), (6) Upper Claiborne Expanded Fault Zone Gas (50470125), and (7) Upper Claiborne Slope and Basin Floor Gas (50470126). Total estimated mean undiscovered conventional hydrocarbon resources in the seven assessment units combined are 52 million barrels of oil, 19.145 trillion cubic feet of natural gas, and 1.205 billion barrels of natural gas liquids. A recurring theme that emerged from the evaluation of the seven Claiborne AUs is that the great bulk of undiscovered hydrocarbon resources comprise non-associated gas and condensate contained in deep (mostly >12,000 feet), overpressured, structurally complex outer shelf or slope and basin floor reservoirs. The continuing development of these downdip objectives is expected to be the primary focus of exploration activity for the onshore Middle Eocene Gulf Coast in the coming decades.

Observations and Modeling of Upper Ocean Hydrography in the Western Arctic With Implications for Acoustic Propagation

DTIC Science & Technology

2016-12-01

2016 Dissertation Supervisors: Wieslaw Maslowski John Colosi THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved...level is 4% of the standard GM value. Frequency spectra of spice show a form similar to the internal-wave spectra but with a steeper spectral slope...Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release

Influences of elevated heating effect by the Himalaya on the changes in Asian summer monsoon

NASA Astrophysics Data System (ADS)

He, Bian

2017-05-01

Based on a series of topographical and thermal sensitivity experiments, the physical processes on the changes of Asian summer monsoon caused by the Himalaya elevated heating were investigated. Six different Himalaya-Iranian Plateau mountain heights were used: 0, 20, 40, 60, 80, and 100 % in the first group (called HIM). The no sensible heating experiments (called HIM_NS) were also performed with the same six mountain heights, but the surface sensible heating was not allowed to heat the atmosphere. The results indicate that the elevated heating effect of the Himalaya gradually intensified when the Himalaya uplifts. The establishment of SASM over the South Asian land which is characterized by the strong precipitation over south slope of the Tibetan Plateau and the huge warm anticyclone in the upper troposphere are in proportion to the elevated heating effect of the Himalaya. Further analysis suggests that the surface heat fluxes over the Himalaya keep almost unchanged during the uplifting, but the lifted condensation level reduces gradually over the regions where the mountain uplifts. The condensation moisturing increases correspondingly and leads to the increase of latent heating in the upper troposphere. Therefore, the positive feedback between the moist convection over the south slope of the Himalaya and monsoon circulation over Indian subcontinent forms and the successive precipitation over the South Asian land is maintained.

Development and validation of a habitat suitability model for ...

EPA Pesticide Factsheets

We developed a spatially-explicit, flexible 3-parameter habitat suitability model that can be used to identify and predict areas at higher risk for non-native dwarf eelgrass (Zostera japonica) invasion. The model uses simple environmental parameters (depth, nearshore slope, and salinity) to quantitatively describe habitat suitable for Z. japonica invasion based on ecology and physiology from the primary literature. Habitat suitability is defined with values ranging from zero to one, where one denotes areas most conducive to Z. japonica and zero denotes areas not likely to support Z. japonica growth. The model was applied to Yaquina Bay, Oregon, USA, an area that has well documented Z. japonica expansion over the last two decades. The highest suitability values for Z. japonica occurred in the mid to upper portions of the intertidal zone, with larger expanses occurring in the lower estuary. While the upper estuary did contain suitable habitat, most areas were not as large as in the lower estuary, due to inappropriate depth, a steeply sloping intertidal zone, and lower salinity. The lowest suitability values occurred below the lower intertidal zone, within the Yaquina River channel. The model was validated by comparison to a multi-year time series of Z. japonica maps, revealing a strong predictive capacity. Sensitivity analysis performed to evaluate the contribution of each parameter to the model prediction revealed that depth was the most important factor. Sh

Identification of potential rockfall source areas at a regional scale using a DEM-based geomorphometric analysis

NASA Astrophysics Data System (ADS)

Loye, A.; Jaboyedoff, M.; Pedrazzini, A.

2009-10-01

The availability of high resolution Digital Elevation Models (DEM) at a regional scale enables the analysis of topography with high levels of detail. Hence, a DEM-based geomorphometric approach becomes more accurate for detecting potential rockfall sources. Potential rockfall source areas are identified according to the slope angle distribution deduced from high resolution DEM crossed with other information extracted from geological and topographic maps in GIS format. The slope angle distribution can be decomposed in several Gaussian distributions that can be considered as characteristic of morphological units: rock cliffs, steep slopes, footslopes and plains. A terrain is considered as potential rockfall sources when their slope angles lie over an angle threshold, which is defined where the Gaussian distribution of the morphological unit "Rock cliffs" become dominant over the one of "Steep slopes". In addition to this analysis, the cliff outcrops indicated by the topographic maps were added. They contain however "flat areas", so that only the slope angles values above the mode of the Gaussian distribution of the morphological unit "Steep slopes" were considered. An application of this method is presented over the entire Canton of Vaud (3200 km2), Switzerland. The results were compared with rockfall sources observed on the field and orthophotos analysis in order to validate the method. Finally, the influence of the cell size of the DEM is inspected by applying the methodology over six different DEM resolutions.

Ground Wave Emergency Network Final Operational Capability: Environmental Assessment for Northwestern Nebraska Relay Node, Site Number RN 8C930NE

DTIC Science & Technology

1993-02-19

some of the small elm trees that comprise the remains of an old shelterbelt. Access would be from School Road. Thirty-seven feet of access road would...low but very rugged cliffs known as the Pine Ridge Escarpment. This extends along the southern and eastern edges of the SSA, represented in Figure 1.1...sandstone occur on the steeper slopes just below the Pine Ridge Escarpment; silty soils derived from loess occur on the broad, gentle slopes between the

Diagnostic Analysis of Second Strengthen Heavy Rain in Western Guangdong for NO.1011 Typhoon Fanapi

NASA Astrophysics Data System (ADS)

Liu, L.

2013-12-01

In order to learn more about the development mechanism of the rainstorm which is caused by No.1101 super typhoon "Fanapi", this paper use weather diagnostic methods to study two processes of heavy rain after "Fanapi" landed in the western part of Guangdong by applying Ncep1 ° × 1 ° reanalysis data and observed precipitation data. Through the preliminary analysis of this typhoon rainstorm, the result shows that cold air and water vapor transmission mainly cause the second strengthen precipitation ,the isoline slope of pseudoequivalent potential temperature reflect the second strengthen precipitation ,the upper troposphere high potential vorticity pass down and the cold dry air in the upper atomosphere confronts with the warm moist air in the lower atmosphere so that the precipitation increase.

High-field pauli-limiting behavior and strongly enhanced upper critical magnetic fields near the transition temperature of an arsenic-deficient LaO0.9F0.1FeAs1-delta superconductor.

PubMed

Fuchs, G; Drechsler, S-L; Kozlova, N; Behr, G; Köhler, A; Werner, J; Nenkov, K; Klingeler, R; Hamann-Borrero, J; Hess, C; Kondrat, A; Grobosch, M; Narduzzo, A; Knupfer, M; Freudenberger, J; Büchner, B; Schultz, L

2008-12-05

We report upper critical field Bc2(T) data for disordered (arsenic-deficient) LaO0.9F0.1FeAs1-delta in a wide temperature and magnetic field range up to 47 T. Because of the large linear slope of Bc2 approximately -5.4 to -6.6 T/K near Tc approximately 28.5 K, the T dependence of the in-plane Bc2(T) shows a flattening near 23 K above 30 T which points to Pauli-limited behavior with Bc2(0) approximately 63-68 T. Our results are discussed in terms of disorder effects within [corrected] unconventional superconducting pairings.

Submarine landslides along the eastern Mediterranean Israeli continental slope - a possible source for tsunami

NASA Astrophysics Data System (ADS)

Katz, O.; Reuven, E.; Aharonov, E.

2013-12-01

Numerous shallow submarine slope failures (scars and deposits) are observed in recent high resolution bathymetric grids of the continental slope off the Israeli eastern Mediterranean coast. The nature of these slope failures is currently not comprehensively understood as well as the question of whether the eastern Mediterranean continental slope is continuously or episodically unstable. This question is relevant to tsunami hazard along the densely populated eastern Mediterranean shores. We report here first steps towards understanding the present state of this submarine landslide system, which include mapping and analyzing the geology of the landslides and the hosting slopes. The continental slope extends from water depths of about 150 to more than 1000 meters with a slope of less than 5 degrees in general. Bathymetric grids with pixel resolution of 15 m till water depth of 700 m and 50 m till water depth of 1700 m were used. Analyzing the bathymetry revealed three main submarine surface features on the continental slope: (a) numerous shallow landslides, within the upper sequence of the post-Messenian sediments. Landslide widths range between hundreds to thousand of meters at the scar, with scar heights up to hundred meters. The toes of the landslides are not always mapable and lay up to a few kilometers down slope from the scar. Slope angles within the scars are 5 degrees to more than 15 degrees. In general landslides size decreases from south to north where their head scar depth turns to be shallower northwards. At least two types of landslides were detected: presumably young slides with sharp scars and presumably old slides with secondary slides and secondary drainage systems developed within the scar area; (b) a few kilometers long, north striking step-like lineaments. Step heights are up to 100 meters and the slopes are up to 20 degrees. The offset between parallel steps is less than a kilometer to a few kilometers. Analyzing seismic lines, the steps are interpreted as surface expressions of growth faults rooted at the Messinian evaporates up to 1.5 kilometers below surface; (c) a few north striking channels were also detected with steep walls of more than 15 degrees, up to two kilometers width and a few kilometers length. The nature of these channels is not clear yet although apparently they are also a surface expressions of the growth faults rooted at the Messinian evaporates. Field relations show that the landslides, both young and old, either emerge from the over-steepened steps, or are displaced by them, and hence submarine landslides and steps are apparently contemporaneous. In addition this suggests that salt dynamics at depth is a main drive for at least some of these shallow slides. The above preliminary results testify to the complicated and highly dynamic nature of the studied continental slope, yet to be revealed.

Real-time monitoring of bluff stability at Woodway, Washington, USA

USGS Publications Warehouse

Baum, R.L.; Harp, E.L.; Likos, W.J.; Powers, P.S.; LaHusen, R.G.; ,

1998-01-01

On January 15, 1997, a landslide of approximately 100,000-m3 from a coastal bluff swept five cars of a freight train into Puget Sound at Woodway, Washington, USA, 25 km north of downtown Seattle. The landslide resulted from failure of a sequence of dense sands and hard silts of glacial and non-glacial origin, including the Lawton Clay, a hard, jointed clayey silt that rarely fails in natural slopes. Joints controlled ground-water seepage through the silt and break-up of the landslide mass. During September of 1997, the US Geological Survey began measuring rainfall, ground-water pressures, and slope movement at the bluff where the landslide occurred. Data are collected every 15 minutes and updated hourly on the World-Wide-Web. Pore pressures observed from September 1997 to February 1998 generally were low and pressures near the bluff face, in the upper few meters of the hard clayey silt, increased gradually.

Carbon isotopic data from test hole USW UZ-1, Yucca Mountain, Nevada

USGS Publications Warehouse

Yang, In C.; Peters, C.A.; Thorstenson, D.C.

1993-01-01

Rock-CO2-gas analyses in test hole USW UZ-1 at Yucca Mountain indicate that gas movement in the unsaturated zone is likely through a dry-fracture system with little porewater or caliche-calcite interaction. This is because near-surface ??13C values are of biogenic origin and have changed little throughout the total depth. Post-bomb 14C activity is observed to the depth of about 12 m. An abrupt change in plotted 14C/depth slope is seen at 61 m. The less steep upper segment corresponds to the zone with greater porosity and moisture content, and consequently more tortuosity, with an estimated traveltime of 1.27 cm/yr; the steeper sloped zone corresponding to the lower segment has smaller porosity and moisture content but larger fracture density for gas transport, with an estimated traveltime of 3.26 cm/yr.

The burrowing activity of scorpions ( Scorpio maurus palmatus) and their potential contribution to the erosion of Hamra soils in Karkur, central Israel

NASA Astrophysics Data System (ADS)

Rutin, J.

1996-03-01

The burrowing activity of the scorpion Scorpio maurus palmatus was studied on a 1200 m 2 slope of a so-called "Hamra" sandy soil in Karkur, Israel. The main results were (1) The scorpions excavate soil material after rain storms, preparing this material for erosion processes by rain splash and rainwash. (2) The burrowing activity stops in the dry summer and during cold days of the winter. This means that Scorpio Maurus Palmatus is preparing soil for erosion from one storm to the next, and not from one season to the next as was previously thought. Further, it was found that the amount of soil material excavated from the burrow is proportional to the size of the scorpion and that most of the mounds were deposited toward the upper part of the slope which means that part is washed back into the burrow itself.

The aerodynamics of Argentavis, the world's largest flying bird from the Miocene of Argentina

PubMed Central

Chatterjee, Sankar; Templin, R. Jack; Campbell, Kenneth E.

2007-01-01

We calculate the flight performance of the gigantic volant bird Argentavis magnificens from the upper Miocene (≈6 million years ago) of Argentina using a computer simulation model. Argentavis was probably too large (mass ≈70 kg) to be capable of continuous flapping flight or standing takeoff under its own muscle power. Like extant condors and vultures, Argentavis would have extracted energy from the atmosphere for flight, relying on thermals present on the Argentinean pampas to provide power for soaring, and it probably used slope soaring over the windward slopes of the Andes. It was an excellent glider, with a gliding angle close to 3° and a cruising speed of 67 kph. Argentavis could take off by running downhill, or by launching from a perch to pick up flight speed. Other means of takeoff remain problematic. PMID:17609382

Newly discovered abundant fluid seep indicators off southern Costa Rica, imaged from overlapping multibeam swaths and 3D seismic data

NASA Astrophysics Data System (ADS)

Kluesner, J. W.; Silver, E. A.; Gibson, J. C.; Bangs, N. L.; McIntosh, K.; von Huene, R.; Orange, D.; Ranero, C. R.

2012-12-01

Offshore southern Costa Rica we have identified 161 potential fluid seepage sites on the shelf and slope regions within an 11 x 55 km strip where no fluid indicators had been reported previously using conventional deep-water mutlibeam bathymetry (100 m grid cell size) and deep towed side scan sonar. Evidence includes large and small pockmarks, mounds, ridges, and slope failure features with localized anomalous high-amplitude backscatter strength. The majority of seepage indicators are associated with shallow sub-bottom reversed polarity bright spots and flat spots imaged within the CRISP 3D seismic grid. Data were collected ~50 km west of Osa Peninsula, Costa Rica onboard the R/V Marcus G. Langseth during the spring of 2011. We obtained EM122 multibeam data using fixed, closely spaced receiver beams and 9-10 times swath overlap, which greatly improved the signal-to-noise ratio and sounding density and allowed for very small grid and mosaic cell sizes (2-10 m). A gas plume in the water column, seen on a 3.5 kHz profile, is located along a fault trace and above surface and subsurface seep indicators. Fluid indicators on the outer shelf occur largely on a dense array of faults, some of which cut through the reflective basement. Seismic flat spots commonly underlie axes of large anticlines on the shelf and slope. Pockmarks are also located at the foot of mid-slope canyons, very near to the upper end of the BSR. These pockmarks appear to be associated with canyon abandonment and folded beds that channel fluids upward, causing hydrate instability. Our findings suggest that significant amounts of methane are venting into ocean and potentially into the atmosphere across the heavily deformed shelf and slope of Costa Rica.

Characterization of Joint Sets Through UAV Photogrammetry on Sedimentary Rock Sea Cliffs and Abrasion Platforms in Northern Taiwan

NASA Astrophysics Data System (ADS)

Hsieh, P. C.; LU, A.; Yeh, C. H.; Huang, W. K.; Lin, H. H.; Lin, M. L.

2017-12-01

Rockfall hazards are very common in obsequent slope and oblique slope. In the coastal area of northern Taiwan, many sea cliffs are formed by obsequent slope and oblique slope. A famous case of rockfall failure happened on Aug. 31, 2013, a 150-ton rock block fell on the highway in Badouzi, Keelung, during a high intensity rainfall event which was caused by Typhoon No.15 (Kong-rey). To reduce this kind of rockfall hazard, it is important to characterize discontinuous planes in the bedrock because rock blocks are mainly divided from bedrock by two or more sets of discontinuous planes including joint planes and the bedding plane. For doing characterization of those fracture patterns of joint sets, it is necessary to do detailed field investigations. However, the survey of discontinuous planes, especially joint sets, are usually difficult and cannot get enough characterization data about joint sets. The first reason is that doing field investigations on the surface of sea cliffs is very dangerous and difficult for engineers or geologists to approach the upper part of outcrop. The second reason is the complexity of joint sets. In Badouzi area, each cliff is constituted by many different layers such as sandstone, shale, or alternations of sandstone and shale, and each layer has different fracture pattern of joint sets. In this study, we use UAV photogrammetry as a solution of these difficulties. UAV photogrammetry can produce a high-resolution digital surface model (DSM), orthophoto, and anaglyph of sea cliffs and abrasion platforms. Than we use self-developed geoprocessing toolsets to auto-trace joint planes with DSM data and produce fracture pattern of joint sets semi-automatically and systematically. Our method can provide basic information for rock mass rating on rock slope stability and rockfall hazards evaluation.

Hazard analysis on the Mid-Atlantic Continental Slope, DCS lease sale 59 Area

USGS Publications Warehouse

Cardinell, Alex P.; Keer, Frederick R.

1982-01-01

A multi-parameter high-resolution seismic survey covering 253 offshore lease blocks was undertaken for analysis of critical structural and depositional features and a suite of piston cores was examined for geotechnical properties on the Mid-Atlantic continental slope in the OCS Lease Sale 59 area. The analysis of this data revealed complex interrelationships between a number of buried structural and depositional features indicating the existence of a variety of slope environments in the proposed lease sale area. The relationship these depositional features have to fault scarps and other topographic irregularities is critical to hazards assessment in this area. Southwest of the Hudson Canyon area, a major slump complex was partially delineated and numerous drape structures, which in some cases appear to have developed into contemporaneous down-to-the-basin faults, are associated with topographic irregularities. Southwest of the Baltimore Canyon area, slumps may be a result of the formation of mud diapers. These diapers? are the first reported in the Mid-Atlantic continental slope. Piston cores were collected at selected locations to provide information on geotechnical strength parameters of slumps, slides, and undisturbed sediments. These data indicate that localized areas of under consolidated sediments are found on valley walls and ridges of the upper slope. These zones may represent discrete areas where either mass movement has occurred or the potential for mass movement may exist. Many of the mass-movement features identified in the OCS Lease Sale 59 area may be Pleistocene in age and are related to' conditions prevailing during low sea stands. Since these conditions are presently absent, the potential for sediment mass movement does not appear to present a major problem to oil and gas operations within the proposed OCS Lease Sale 59 area.

Pore Pressure Distribution and Flank Instability in Hydrothermally Altered Stratovolcanoes

NASA Astrophysics Data System (ADS)

Ball, J. L.; Taron, J.; Hurwitz, S.; Reid, M. E.

2015-12-01

Field and geophysical investigations of stratovolcanoes with long-lived hydrothermal systems commonly reveal that initially permeable regions (such as brecciated layers of pyroclastic material) can become both altered and water-bearing. Hydrothermal alteration in these regions, including clay formation, can turn them into low-permeability barriers to fluid flow, which could increase pore fluid pressures resulting in flank slope instability. We examined elevated pore pressure conditions using numerical models of hydrothermal flow in stratovolcanoes, informed by geophysical data about internal structures and deposits. Idealized radially symmetric meshes were developed based on cross-sectional profiles and alteration/permeability structures of Cascade Range stratovolcanoes. We used the OpenGeoSys model to simulate variably saturated conditions in volcanoes heated only by regional heat fluxes, as well as 650°C intrusions at two km depth below the surface. Meteoric recharge was estimated from precipitation rates in the Cascade Range. Preliminary results indicate zones of elevated pore pressures form: 1) where slopes are underlain by continuous low-permeability altered layers, or 2) when the edifice has an altered core with saturated, less permeable limbs. The first scenario might control shallow collapses on the slopes above the altered layers. The second could promote deeper flank collapses that are initially limited to the summit and upper slopes, but could progress to the core of an edifice. In both scenarios, pore pressures can be further elevated by shallow intrusions, or evolve over longer time scales under forcing from regional heat flux. Geometries without confining low-permeability layers do not show these pressure effects. Our initial scenarios use radially symmetric models, but we are also simulating hydrothermal flow under real 3D geometries with asymmetric subsurface structures (Mount Adams). Simulation results will be used to inform 3D slope-stability models.

Dynamics of the Wulong Landslide Revealed by Broadband Seismic Records

NASA Astrophysics Data System (ADS)

Huang, X.; Dan, Y.

2016-12-01

Long-period seismic signals are frequently used to trace the dynamic process of large scale landslides. The catastrophic WuLong landslide occurred at 14:51 on 5 June 2009 (Beijing time, UTC+8) in Wulong Prefecture, Southwest China. The topography in landslide area varies dramatically, enhancing the complexity in its movement characteristics. The mass started sliding northward on the upper part of the cliff located upon the west slope of the Tiejianggou gully, and shifted its movement direction to northeastward after being blocked by stable bedrock in front, leaving a scratch zone. The sliding mass then moved downward along the west slope of the gully until it collided with the east slope, and broke up into small pieces after the collision, forming a debris flow along the gully. We use long-period seismic signals extracted from eight broadband seismic stations within 250 km of the landslide to estimate its source time functions. Combining with topographic surveys done before and after the event, we can also resolve kinematic parameters of sliding mass, i.e. velocities, displacements and trajectories, perfectly characterizing its movement features. The runout trajectory deduced from source time functions is consistent with the sliding path, including two direction changing processes, corresponding to scratching the western bedrock and collision with the east slope respectively. Topographic variations can be reflected from estimated velocities. The maximum velocity of the sliding mass reaches 35 m/s before the collision with the east slope of the Tiejianggou gully, resulting from the height difference between the source zone and the deposition zone. What is important is that dynamics of scratching and collision can be characterized by source time functions. Our results confirm that long-period seismic signals are sufficient to characterize dynamics and kinematics of large scale landslides which occur in a region with complex topography.

Effect of unstable layer depth on the pore pressure distribution, case study of the Slano Blato landslide (Slovenia)

NASA Astrophysics Data System (ADS)

Askarinejad, Amin; Secchi, Bandar; Macek, Matej; Petkovsek, Ana; Springman, Sarah

2013-04-01

The Slano Blato landslide is one of the largest landslides in Slovenia with a volume of more than 1 mio m3 of moving debris. The landslide is located at the border of Triassic limestone and Eocene flysch formations. Flysch is composed of layers of marls and sandstones. The sliding mass consists mainly of clay and clayey gravel of highly weathered and deteriorated flysch, while a minor part represents grains and blocks of limestones. (Petkovšek et al., 2009). The first documentation of an instability event dates back to 1789 and the landslide was reactivated during a heavy rain period in November 2000. Since then, the ground surface level above the unstable material on the upper zones of the landslide is significantly decreasing so that the current slope surface is now more than 10 m below the terrain surveyed in 1998. The new landslide topography results in different pore pressure distributions in the slope, which were anticipated to have a detrimental effect on the stability and movement regime of the slope. The main goal of this work is to investigate the effect of the overlying debris depth on the pore water pressure distribution during a predefined precipitation scenario. The behaviour of the unsaturated soil and the effects of fissures in the bedrock are also considered in the analysis. Hydro-mechanical simulations were performed using 2D finite element software (PLAXIS) and numerical results are compared with results from analytical models, which use a 1D steady state formulation for the hydraulic part and a 2D limit equilibrium approach to calculate the safety factors. The numerical studies show significant change in the pore water pressure distribution in the landslide body with variation of the debris depth. An increase in the debris depth leads to higher suction due to the deeper location of the water table. Higher suction increases landslide stability due to: i) increase of the effective stress and hence the shear strength of the material and ii) decrease of the unsaturated hydraulic conductivity. Accordingly, a longer rainfall event with a similar intensity is required to destabilize the slope. The calculated suction profile for the current slope surface was compared to the in situ measurements, and the results show partial agreement. The slight discrepancy might be attributed to several factors such as: i) possible difference in the height of the water table in the model and reality, ii) differences in location between observation points in numerical model and in-situ observations, as there are no tensiometers in the upper part of the slope, iii) modelling the underlying flysch layer as a homogenous and isotropic material in PLAXIS, which is not the case in reality. Reference: Petkovsek, A., Macek, M., Kocevar, M., Benko, I., Majes, B., 2009. Soil matric suction as an indicator of the mud flow occurrence. 17th International Conference of Soil Mechanics and Geotechnical Engineering, Alexandria, Egypt, 1855 - 1860.

Acoustic Velocity Of The Sediments Offshore Southwestern Taiwan

NASA Astrophysics Data System (ADS)

Tsai, C.; Liu, C.; Huang, P.

2004-12-01

Along the Manila Trench south of 21øXN, deep-sea sediments are being underthrusted beneath the Taiwan accretionary prism which is composed of the Kaoping Slope and Hengchun Ridge. Offshore southwestern Taiwan, foreland sediments and Late Miocene strata of the Tainan Basin are being accreted onto the fold-and thrust belt of the syn-collision accretionary wedge of the Kaoping Slope. The Kaoping Slope consists of thick Neogene to Recent siliciclastics deformed by fold-and-thrust structures and mud diapers. These Pliocene-Quaternary sediments deposited in the Kaoping Shelf and upper slope area are considered to be paleo-channel deposits confined by NNE-SSW trend mud diapiric structure. Seismic P-wave velocities of the sediment deposited in the Kaoping Shelf and Kaoping Slope area are derived from mutichannel seismic reflection data and wide-angle reflection and refraction profiles collected by sonobuoys. Sediment velocity structures constrained from mutichannel seismic reflection data using velocity spectrum analysis method and that derived from sonobuoy data using tau-sum inversion method are compared, and they both provide consistent velocity structures. Seismic velocities were analyzed along the seismic profile from the surface to maximum depths of about 2.0 km below the seafloor. Our model features a sediment layer1 with 400 ms in thickness and a sediment layer2 with 600 ms in thickness. For the shelf sediments, we observe a linear interval velocity trend of V=1.53+1.91T in layer1, and V=1.86+0.87T in layer2, where T is the one way travel time within the layer. For the slop sediment, the trend of V=1.47+1.93T in layer1, and V=1.70+1.55T in layer2. The layer1¡¦s velocities gradients are similar between the shelf (1.91 km/sec2) and the slope(1.93 km/sec2). It means layer1 distributes over the slope and shelf widely. The result of the sediment velocity gradients in this area are in good agreement with that reported for the south Atlantic continental margins.

The ESASSI-08 cruise in the South Scotia Ridge region: Water masses, currents, and the ASF

NASA Astrophysics Data System (ADS)

Palmer, M.; Gomis, D.; Flexas, M. M.; Jordà, G.; Orsi, A. H.

2009-04-01

The ESASSI-08 oceanographic cruise carried out in January 2008 was the major milestone of ESASSI, the Spanish component of SASSI (a core project of the International Polar Year devoted to study the shelf-slope exchanges in different locations of Antarctica). The specific objectives of ESASSI, the sampling strategy and the overall distribution of the main variables across the 11 sections covered by the cruise are presented in a poster. Here we focus on three specific issues: i) the observation of strong tidal currents over some of the sampled slopes; ii) the path of the Antarctic Slope Front (ASF) over the SSR; and iii) the outflow of dense, ventilated water from the Weddell Sea into the South Scotia Sea. The main results are: i) Strong tidal currents with a significant diurnal component were observed over the southern slope of the SSR. Three tidal models are compared with the observations and used to de-tide ADCP currents. ii) The signature of the ASF is clearly detected on the southern slopes of the SSR (on the Weddell Sea flank). Over the northern slopes (the Scotia Sea flank), however, only weak signatures of frontal structures are observed; an in-depth biochemical analysis will be required to link the structures observed over the two flanks of the SSR. What seems clear is that the ASF does not extend further than Elephant Island, since southwestward of that island the shelf and the slope are fully occupied by Circumpolar Deep Water (CDW) from the Antarctic Circumpolar Current. iii) The shallower component of Weddell Sea Deep Water (Upper WSDW) flows over the SSR and pours into the Scotia Sea except to the east of Elephant Island, where the channels are less than 1500 m deep. The densest component of WSDW (Lower WSDW) is observed at both flanks of the SSR, but again a more detailed analysis of biochemical data will be required to prove a direct flux of this water mass across the SSR. Weddell Sea Bottom Water (WSBW) is not observed in any of the sampled sections.

Recent Sedimentary Processes Along the Western Continental Margin of the South Korea Plateau, East Sea of Korea

NASA Astrophysics Data System (ADS)

Cukur, D.; Um, I. K.; Bahk, J. J.; Chun, J. H.; Lee, G. S.; Soo, K. G.; Horozal, S.; Kim, S. P.

2017-12-01

The continental margins of the marginal seas is largely shaped by a complex interplay of sediment transport processes directed both downslope and along-slope. Factors influence the sediment transport from shelf to the deep basin include: (i) seabed morphology, (ii) climate, (iii) sea level changes, (iv) slope stability, (v) oceanographic regime, and (vi) sediment sources. In order to understand the recent sedimentary processes along the western margin of the South Korea Plateau in the East Sea, we collected multiple geophysical datasets including the subbottom profiler and multibeam echosounder as well as geological sampling. Twelve echo types have been defined and interpreted as deposits formed by shallow marine, hemipelagic sedimentation, bottom currents, combined- (mass-movement/hemipelagic and hemipelagic/turbidites) and mass-movement-processes. Hemipelagic sedimentation, which is reflected as undisturbed layered sediments, appears to have been the primary sedimentary process throughout the study area. Two major slope-parallel channels appear to have acted as major conduits for turbidity currents from shallower shelf into the deep basins. Bottom current deposits, which is expressed as undulating seafloor morphology, are prevalent in the southern mid-slope at water depths between 250 to 450 m. Mass-transport deposits, consisting of chaotic seismic facies, occur in the upper and lower parts of the continental slope. Piston cores confirm the presence of MTDs that are characterized by mud clasts of variable size and shape. Multibeam bathymetry data show that these MTDs chiefly initiate on lower-slopes (400-600 m) where the gradient is up to 3°. In addition, subbottom profiles suggest the presence of numerous faults in close vicinity of headwall scarps; some are extending to the seafloor suggesting their recent activity. Earthquakes associated with tectonic activity are considered as the main triggering mechanism for these MTDs. Overall, the acoustic facies distribution shows that the sedimentary processes change downslope and differ within each physiographic province. In particular, the role of geological inheritance (i.e., structural folds and faults) on the geomorphology and sediment facies on the lower slopes appears to be quite important.

A reevaluation of the Munson-Nygren-Retriever submarine landslide complex, Georges bank lower slope, western north Atlantic

USGS Publications Warehouse

Chaytor, Jason D.; Twichell, David C.; ten Brink, Uri S.

2012-01-01

The Munson-Nygren-Retriever (MNR) landslide complex is a series of distinct submarine landslides located between Nygren and Powell canyons on the Georges Bank lower slope. These landslides were first imaged in 1978 using widely-spaced seismic reflection profiles and were further investigated using continuous coverage GLORIA sidescan imagery collected over the landslide complex in 1987. Recent acquisition of highresolution multibeam bathymetry across these landslides has provided an unprecedented view of their complex morphology and allows for a more detailed investigation of their evacuation and deposit morphologies and sizes, modes of failure, and relationship to the adjacent sections of the margin, including the identification of an additional landslide within the MNR complex, referred to here as the Pickett slide. The evacuation zone of these landslides covers an area of approximately 1,780 km2 . The headwalls of these landslides are at a depth of approximately 1,800 m, with evacuation extending for approximately 60 km downslope to the top of the continental rise. High-relief debris deposits, in the form of blocks and ridges, are present down the length of the majority of the evacuation zones and within the deposition area at the base of the slope. On the continental rise, the deposits from each of the most recent failures of the MNR complex landslides merge with debris from earlier continental slope failures, canyon and alongslope derived deposits, and prominent upper-rise failures.

Stratigraphy of Atlantic coastal margin of United States north of Cape Hatteras; brief survey

USGS Publications Warehouse

Perry, W.J.; Minard, J.P.; Weed, E.G.A.; Robbins, E.I.; Rhodehamel, E.C.

1975-01-01

A synthesis of studies of sea-floor outcrops of the sedimentary wedge beneath the northeastern United States continental shelf and slope and a reassessment of coastal plain Mesozoic stratigraphy, particularly of the coastal margin, provide insight for estimating the oil and gas potential and provide geologic control for marine seismic investigations of the Atlantic continental margin. The oldest strata known to crop out on the continental slope are late Campanian in age. The Cretaceous-Tertiary contact along the slope ranges from a water depth of 0.6 to 1.5 km south of Georges Bank to 1.8 km in Hudson Canyon. Few samples are available from Tertiary and Late Cretaceous outcrops along the slope. Sediments of the Potomac Group, chiefly of Early Cretaceous age, constitute a major deltaic sequence in the emerged coastal plain. This thick sequence lies under coastal Virginia, Maryland, Delaware, southeastern New Jersey, and the adjacent continental shelf. Marine sands associated with this deltaic sequence may be present seaward under the outer continental shelf. South of the Norfolk arch, under coastal North Carolina, carbonate rocks interfinger with Lower Cretaceous clastic strata. From all available data, Mesozoic correlations in coastal wells between coastal Virginia and Long Island have been revised. The Upper-Lower Cretaceous boundary is placed at the transition between Albian and Cenomanian floras. Potential hydrocarbon source beds are present along the coast in the subsurface sediments of Cretaceous age. Potential reservoir sandstones are abundant in this sequence.

Spatial Arrangement of Branches in Relation to Slope and Neighbourhood Competition

PubMed Central

SUMIDA, AKIHIRO; TERAZAWA, IKUE; TOGASHI, ASAKO; KOMIYAMA, AKIRA

2002-01-01

To gain a better understanding of the effects of spatial structure on patterns of neighbourhood competition among hardwood trees, the three‐dimensional extension of primary branches was surveyed for ten community‐grown Castanea crenata (Fagaceae) trees with respect to the positioning of neighbouring branches and the slope of the forest floor. There were significantly more branches extending towards the lower side of the slope than towards the upper side, but structural properties such as branch length and vertical angle were not affected by slope. When horizontal extension of a branch towards its neighbour was compared for a C. crenata branch and a neighbouring heterospecific, the former was significantly narrower than the latter when the inter‐branch distance (horizontal distance between the base positions of two neighbouring branches) was short (< approx. 5 m). Castanea crenata branches tended to extend in a direction avoiding neighbouring branches of heterospecifics when the inter‐branch distance was short. Furthermore, for an inter‐branch distance <3 m, the horizontal extension of a C. crenata branch was less when it was neighbouring a heterospecific branch than when neighbouring a conspecific branch. These results suggest that horizontal extension of C. crenata branches is more prone to spatial invasion by nearby neighbouring branches of heterospecifics, and that the invasion can be lessened when C. crenata trees are spatially aggregated. The reason why such an arrangement occurs is discussed in relation to the later leaf‐flush of C. crenata compared with that of other species in the forest. PMID:12096742

The morphology and nature of the East Arctic ocean acoustic basement

NASA Astrophysics Data System (ADS)

Rekant, Pavel

2017-04-01

As the result of the thorough interpretation and cross-correlation of the large seismic dataset (>150000 km and >600 seismic lines), the depth structure map of the acoustic basement was constrained. Tectonic framework, basement surface morphology and linkage of the deep basin structures with shelves ones, was significantly clarified based on the map. It becomes clear that most morphostructures presently located within deep-water basin are tectonically connected with shelf structures. Acoustic basement contains a number of pre-Cambrian, Caledonian and Mesozoic consolidated blocks. The basement heterogeneity is highlighted by faults framework and basement surface morphology differences, as well thickness and stratigraphy of the sediment cover. The deepest basins of the East Arctic - Hanna Trough, North Chukchi and Podvodnikov Basins form a united mega-depression, wedged between pre-Cambrian continental blocks (Chukchi Borderland - Mendeleev Rise - Toll Saddle) from the north and the Caledonian deformation front from the south. The basement age/origin speculations are consistent with paleontological and U-Pb zircon ages from dredged rock samples. Most of morphological boundaries in the modern Arctic differ considerably from the tectonic framework. Only part of the Arctic morphostructures is constrained by tectonic boundaries. They are: eastern slope of the Lomonosov Ridge, continental slope in the Laptev Sea, upper continental slope in the Podvodnikov Basin, southern slope of the North Chukchi Basin and borders of the Chukchi Borderland. The rest significant part of modern morphological boundaries are caused by sedimentation processes.

The Impact of Mass Movement and Fluid Flow during Ridge Subduction inferred from Physical Properties and Zeolite Assemblage in the Upper Plate Slope of the Costa Rica Subduction Zone

NASA Astrophysics Data System (ADS)

Hamahashi, M.; Screaton, E.; Tanikawa, W.; Hashimoto, Y.; Martin, K. M.; Saito, S.; Kimura, G.

2015-12-01

The Costa Rica subduction zone offshore Osa Peninsula is known as an erosive margin with active seismicity and the subduction of the Cocos Ridge. One of the major unknowns in this margin is the nature of the unconformity at the base of the slope sediments in the upper plate and the high velocity materials below. To investigate the geologic processes across the unconformity, we examined the consolidation state and mineral assemblages of the sediments at the mid-slope Site 1380 drilled during IODP Expedition 344 by conducting microstructural observation, particle size analysis, X-ray fluorescence/diffraction analysis and resistivity measurement. The general compaction trend is controlled primarily by grain-size sorting and the physical property transition is likely caused by massive sediment removal under normal fault regime, thickness of which range between ~600-850 m determined from the composite porosity-depth curve. Across the unconformity between the late Pliocene~late Pleistocene silty clay (Unit 1) and late Pliocene~early Pleistocene clayey siltstone (Unit 2), the mineral/element components of the sediments is marked by the transitions in zeolite compositions; Unit 1 consists of laumontite and heulandite, whereas below the unconformity, Unit 2 sediments contain analcime, laumontite, and heulandite, but laumontite become less abundant at lower depth. The experienced temperature of the sediments in Unit 2 is estimated to have reached between ~86 and 122℃ as inferred from analcime burial diagenesis. This may correspond with the greater depth range prior to mass movement and normal faulting. The initial analcime burial diagenetic zone was likely cut off by the sediment removal across the unconformity, and later overprinted by high temperature fluid along the boundary forming laumontite and heulandite in the vicinity. These results illustrate that ridge subduction has substantial potential to cause mass movement, an extensional stress regime, and fluid flow from depth.