Bus--carpool FWY lanes in San Francisco area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newman, L.

1976-11-01

The California Department of Transportation is studying ways to increase the use of the urban freeway systems that will accommodate the maximum number of people with the least delay and the maximum possible safety in a cost-effective way. This paper describes operational features of four different projects under way, namely: a contraflow bus lane; a part-time bus lane in the same direction and unseparated from normal traffic; a bus-carpool lane also in the same direction and unseparated from normal traffic; and a preferential access to a metered freeway. (MCW)

75 FR 5847 - Section 5309 Bus and Bus Facilities Livability Initiative and Urban Circulator Program Grants

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

... Livability Initiative and Urban Circulator Program Grants AGENCY: Federal Transit Administration (FTA), DOT. ACTION: Notice to Extend Application Deadline for the Bus and Bus Facilities and Urban Circulator..., Transportation Equity Act: A Legacy for Users (SAFETEA-LU), Public Law 109-59, August 10, 2005. The Urban...

Intelligent Urban Public Transportation for Accessibility Dedicated to People with Disabilities

PubMed Central

Zhou, Haiying; Hou, Kun-Mean; Zuo, Decheng; Li, Jian

2012-01-01

The traditional urban public transport system generally cannot provide an effective access service for people with disabilities, especially for disabled, wheelchair and blind (DWB) passengers. In this paper, based on advanced information & communication technologies (ICT) and green technologies (GT) concepts, a dedicated public urban transportation service access system named Mobi+ has been introduced, which facilitates the mobility of DWB passengers. The Mobi+ project consists of three subsystems: a wireless communication subsystem, which provides the data exchange and network connection services between buses and stations in the complex urban environments; the bus subsystem, which provides the DWB class detection & bus arrival notification services; and the station subsystem, which implements the urban environmental surveillance & bus auxiliary access services. The Mobi+ card that supports multi-microcontroller multi-transceiver adopts the fault-tolerant component-based hardware architecture, in which the dedicated embedded system software, i.e., operating system micro-kernel and wireless protocol, has been integrated. The dedicated Mobi+ embedded system provides the fault-tolerant resource awareness communication and scheduling mechanism to ensure the reliability in data exchange and service provision. At present, the Mobi+ system has been implemented on the buses and stations of line ‘2’ in the city of Clermont-Ferrand (France). The experiential results show that, on one hand the Mobi+ prototype system reaches the design expectations and provides an effective urban bus access service for people with disabilities; on the other hand the Mobi+ system is easily to deploy in the buses and at bus stations thanks to its low energy consumption and small form factor. PMID:23112622

Intelligent urban public transportation for accessibility dedicated to people with disabilities.

PubMed

Zhou, Haiying; Hou, Kun-Mean; Zuo, Decheng; Li, Jian

2012-01-01

The traditional urban public transport system generally cannot provide an effective access service for people with disabilities, especially for disabled, wheelchair and blind (DWB) passengers. In this paper, based on advanced information & communication technologies (ICT) and green technologies (GT) concepts, a dedicated public urban transportation service access system named Mobi+ has been introduced, which facilitates the mobility of DWB passengers. The Mobi+ project consists of three subsystems: a wireless communication subsystem, which provides the data exchange and network connection services between buses and stations in the complex urban environments; the bus subsystem, which provides the DWB class detection & bus arrival notification services; and the station subsystem, which implements the urban environmental surveillance & bus auxiliary access services. The Mobi+ card that supports multi-microcontroller multi-transceiver adopts the fault-tolerant component-based hardware architecture, in which the dedicated embedded system software, i.e., operating system micro-kernel and wireless protocol, has been integrated. The dedicated Mobi+ embedded system provides the fault-tolerant resource awareness communication and scheduling mechanism to ensure the reliability in data exchange and service provision. At present, the Mobi+ system has been implemented on the buses and stations of line '2' in the city of Clermont-Ferrand (France). The experiential results show that, on one hand the Mobi+ prototype system reaches the design expectations and provides an effective urban bus access service for people with disabilities; on the other hand the Mobi+ system is easily to deploy in the buses and at bus stations thanks to its low energy consumption and small form factor.

Biomechanical and ergonomic assessment of urban transit operators.

PubMed

Albert, Wayne J; Everson, Donald; Rae, Michelle; Callaghan, Jack P; Croll, Jim; Kuruganti, Usha

2014-01-01

The prevalence of neck and low back musculoskeletal injuries in transit operators has been shown to be high; with work absences exceeding double the National average. There is a lack of biomechanical data generated from field researches to inform on musculoskeletal risk associated with transportation and driving occupations. Instead there has been a reliance on simulated driving and questionnaire-based research. This study was designed to examine the musculoskeletal and biomechanical stresses experienced by urban bus drivers. The main objective was to obtain a baseline understanding of sitting posture, muscle activiation and subjective ratings of stress during regular driving tasks. Fifteen urban city bus drivers were recruited for this study. Bus drivers drove the same 65-minute bus route once, at the same time of day, in the same preselected bus. Wireless surface electromyography monitored muscular activity of the drivers' neck, upper trapezius, and erector spinae and video analysis and seat pressure mapping was used to monitor changes in driving posture. A health and lifestyle questionnaire was administered to record specific neck and back pain experienced by drivers as well as to provide lifestyle habits. Drivers were found to exhibit non-neutral postures for less than 30% of the time while conducting routine tasks of turning and stopping for passenger loading and unloading. The neck posture was the greatest concern in terms of non-neutral posture and this was supported by the higher muscle activation to the neck musculature. There was significant posture adjustment made during the one-hour driving period with the adjustments increasing with driving time. Activities associated with bus driving appear to require the use of non-neutral postures an increase in muscle activation. Significant postural adjustments were needed over the one-hour observation period suggesting that the musculoskeletal demands may increase over a regular 12-hour shift.

Terminals for Suburb Bus Transport in Bratislava

NASA Astrophysics Data System (ADS)

Schlosser, Tibor; Schlosser, Peter; Cápayová, Silvia; Hodáková, Dominika

2017-10-01

The main objective of this article is to describe the strategy for development of the public transport terminals in the city of Bratislava, Capital of Slovak Republic. The reason goes from the private operator Slovak Lines, who operates the suburb bus transport in the agglomeration of the city. For this operator was created a transport model, while placing emphasis on optimizing the compliance of suburban public transport with urban public transport in the city of Bratislava and evaluating the significance of the new Bus Station to be constructed at Mlynské Nivy - in a new down town centre of the city. The main issue is to ensure the best available offer of public transport (PT) to passengers in the Bratislava agglomeration. The subject of the study was oriented to specify and propose changes in the transport infrastructure and integrated public transport organisation on the area of the city in terms of the significant position of the new Mlynské Nivy Bus Station (MN BS), which is under preparation with realization in the year 2017.

Risk factors for unintentional occupational injury among urban transit bus drivers: a cohort longitudinal study.

PubMed

Wei, Chia; Gerberich, Susan G; Ryan, Andrew D; Alexander, Bruce H; Church, Timothy R; Manser, Michael

2017-12-01

Although many studies have focused on bus operators' occupational diseases, work-related injury and associated risk factor data are limited. The purpose of this longitudinal study was to investigate unintentional injury and exposures that may affect injury risk among metropolitan bus operators. Demographic, work-related, and injury data obtained from a metropolitan transit company for a 5-year period, enabled estimates of rates per 100 full time equivalents (FTEs) and adjusted Hazard Ratios (HRs), with 95% confidence intervals (CIs), using Generalized Estimating Equations and Cox proportional hazards models, respectively. The 2095 bus operators, included in this study, had an unintentional injury rate (95% CI) of 17.8 (16.1-19.7) per 100 FTEs. Multivariable analysis identified increased risks for operators who were female, compared to male (HR = 2.4; 2.0-2.8); worked less than 7 versus 7 to less than 12 hours per day (HR = 4.6; 3.8-5.5); and drove less than 7 versus 7 to less than 12 hours per day (HR = 3.2; 2.7-3.8). Suggestive increased risks were identified for operators working split versus straight shifts (HR = 1.2; 1.0-1.4) and for driving limited versus regular bus routes (HR = 1.36; 1.0-1.8). Results serve as a basis for further studies and inform the development of targeted intervention strategies to reduce bus operators' occupational injuries. Copyright © 2017 Elsevier Inc. All rights reserved.

Bus Propulsion Alternatives Overview

DOT National Transportation Integrated Search

1982-04-01

The Urban Mass Transportation Administration (UMTA) is currently investigating propulsion alternatives which would conserve petroleum-based fuels and would be practical for use by U.S. transit operators. A discussion of these alternatives (electric p...

Tradeoffs between costs and greenhouse gas emissions in the design of urban transit systems

NASA Astrophysics Data System (ADS)

Griswold, Julia B.; Madanat, Samer; Horvath, Arpad

2013-12-01

Recent investments in the transit sector to address greenhouse gas emissions have concentrated on purchasing efficient replacement vehicles and inducing mode shift from the private automobile. There has been little focus on the potential of network and operational improvements, such as changes in headways, route spacing, and stop spacing, to reduce transit emissions. Most models of transit system design consider user and agency cost while ignoring emissions and the potential environmental benefit of operational improvements. We use a model to evaluate the user and agency costs as well as greenhouse gas benefit of design and operational improvements to transit systems. We examine how the operational characteristics of urban transit systems affect both costs and greenhouse gas emissions. The research identifies the Pareto frontier for designing an idealized transit network. Modes considered include bus, bus rapid transit (BRT), light rail transit (LRT), and metro (heavy) rail, with cost and emissions parameters appropriate for the United States. Passenger demand follows a many-to-many travel pattern with uniformly distributed origins and destinations. The approaches described could be used to optimize the network design of existing bus service or help to select a mode and design attributes for a new transit system. The results show that BRT provides the lowest cost but not the lowest emissions for our large city scenarios. Bus and LRT systems have low costs and the lowest emissions for our small city scenarios. Relatively large reductions in emissions from the cost-optimal system can be achieved with only minor increases in user travel time.

Characteristics of urban transportation systems. A handbook for transportation planners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1975-05-01

The objective of the handbook, specifically for use by transportation planners in the evaluation of alternative systems, is to provide a single simplified reference source which characterizes the most important performance characteristics of the following contemporary urban transportation systems: (1) rail (commuter, rapid, and light); (2) local bus and bus rapid transit; (3) automobile-highway system (automobiles and other vehicles); (4) pedestrian assistance systems; and (5) activity center systems--people mover systems that have been installed at airports, zoos, amusement parks, etc. The handbook assesses the supply or performance aspect of urban transportation dealing with passenger demand implicitly. Seven supply parameters studiedmore » are: speed, capacity (service volume), operating cost (vehicle), energy consumption (vehicle or source), pollution, capital cost, and accident frequency.« less

Evaluation of bus emissions generated near bus stops

NASA Astrophysics Data System (ADS)

Yu, Qian; Li, Tiezhu

2014-03-01

The purpose of this research is to demonstrate a methodology for quantification of bus emissions generated near bus stops based on the real-world on-road emissions data collected by the Portable Emission Measurement System (PEMS). Data collection was carried out on an urban diesel bus throughout a bus line under normal operation condition on four work days. Stop influence zone is defined as the area in which the normal bus driving is interrupted by bus stops. The second-by-second data were screened out within the stop influence zone. And the bus running state near a stop was classified into three driving modes, deceleration, idling, and acceleration. Then emission characteristics were analyzed for each mode. Under the idling condition, the emission rates (g s-1) were not constant all the time. The NOX emission rate decreased in the first 4-6 s while the corresponding emission rates of CO2, CO, NOX, and HC increased in the last 4 s of idling. Besides, the influence of bus stop characteristics on emissions was investigated using statistical methods. Platform type, length and location of bus stops showed significant effects on the length of the stop influence zone. However, there were no significant effects on distance-based emission factors.

Public transit research: Rail, bus, and new technology, 1991. Transportation Research Record

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kassabian, N.C.; Tobias, A.G.; Crayton, L.

1991-01-01

The report contains: Image of Rail Transit; Train Operations Computer Simulation Case Study: Single-Tracking Operations for Philadelphia's Market-Frankford Subway Elevated Rail Rapid Transit Line; Transit Railcar Quantities: Scale Economies; Evaluation of Training Programs in Rail Transit: Its Role and Status; Methodology for Evaluating Out-of-Direction Bus Route Segments; Integration of Fixed- and Flexible-Route Bus Systems; Downtown Space for Buses--The Manhattan Experience; Implications of Transit Drug Testing and Maintenance Service Procurement for Small Urban and Rural Systems; Challenges for Integration of Alternative Fuels in the Transit Industry; Short History of the Transbay Transit Terminal and the Relocation of the San Francisco Greyhoundmore » Depot Thereto; Airport Development with Automated People Mover Systems; Review of Four Alternative Airport Terminal Passenger Mobility Systems.« less

Flywheel/Diesel Hybrid Power Drive: Urban Bus Vehicle Simulation.

DOT National Transportation Integrated Search

1978-05-01

This report describes the results of a Transportation Systems Center investigation conducted under Urban Mass Transportation Administration sponsorship, of the practicality of a flywheel/diesel hybrid power drive for urban transit bus propulsion. The...

Traveling by Bus Instead of Car on Urban Major Roads: Safety Benefits for Vehicle Occupants, Pedestrians, and Cyclists.

PubMed

Morency, Patrick; Strauss, Jillian; Pépin, Félix; Tessier, François; Grondines, Jocelyn

2018-04-01

Some studies have estimated fatality and injury rates for bus occupants, but data was aggregated at the country level and made no distinction between bus types. Also, injured pedestrians and cyclists, as a result of bus travel, were overlooked. We compared injury rates for car and city bus occupants on specific urban major roads, as well as the cyclist and pedestrian injuries associated with car and bus travel. We selected ten bus routes along major urban arterials (in Montreal, Canada). Passenger-kilometers traveled were estimated from vehicle counts at intersections (2002-2010) and from bus passenger counts (2008). Police accident reports (2001-2010) provided injury data for all modes. Injury rates associated with car and bus travel were calculated for vehicle occupants, pedestrians, and cyclists. Injury rate ratios were also computed. The safety benefits of bus travel, defined as the number of vehicle occupant, cyclist, and pedestrian injuries saved, were estimated for each route. Overall, for all ten routes, the ratio between car and bus occupant injury rates is 3.7 (95% CI [3.4, 4.0]). The rates of pedestrian and cyclist injuries per hundred million passenger-kilometers are also significantly greater for car travel than that for bus travel: 4.1 (95% CI [3.5, 4.9]) times greater for pedestrian injuries; 5.3 (95% CI [3.8, 7.6]) times greater for cyclist injuries. Similar results were observed for fatally and severely injured vehicle occupants, cyclists, and pedestrians. At the route level, the safety benefits of bus travel increase with the difference in injury rate associated with car and bus travel but also with the amount of passenger-kilometers by bus. Results show that city bus is a safer mode than car, for vehicle occupants but also for cyclists and pedestrians traveling along these bus routes. The safety benefits of bus travel greatly vary across urban routes; this spatial variation is most likely linked to environmental factors. Understanding the safety benefits of public transit for specific transport routes is likely to provide valuable information for mobilizing city and transportation planners.

Common Traffic Violations of Bus Drivers in Urban China: An Observational Study.

PubMed

Wang, Qiqi; Zhang, Wei; Yang, Rendong; Huang, Yuanxiu; Zhang, Lin; Ning, Peishan; Cheng, Xunjie; Schwebel, David C; Hu, Guoqing; Yao, Hongyan

2015-01-01

To report common traffic violations in bus drivers and the factors that influence those violations in urban China. We conducted an observational study to record three types of traffic violations among bus drivers in Changsha City, China: illegal stopping at bus stations, violating traffic light signals, and distracted driving. The behaviors of bus drivers on 32 routes (20% of bus routes in the city) were observed. A two-level Poisson regression examined factors that predicted bus driver violations. The incidence of illegal stopping at bus stations was 20.2%. Illegal stopping was less frequent on weekends, sunny days, and at stations with cameras, with adjusted incidence rate ratios (IRRs) of 0.81, 0.65 and 0.89, respectively. The incidence of violating traffic light signals was 2.2%, and was lower on cloudy than sunny days (adjusted IRR: 0.60). The incidence of distracted driving was 3.3%. The incidence of distracted driving was less common on cloudy days, rainy or snowy days, and foggy/windy/dusty days compared to sunny days, with adjusted IRRs of 0.54, 0.55 and 0.07, respectively. Traffic violations are common in bus drivers in urban China and they are associated with the date, weather, and presence of traffic cameras at bus station. Further studies are recommended to understand the behavioral mechanisms that may explain bus driver violations and to develop feasible prevention measures.

An Optimization Model for the Selection of Bus-Only Lanes in a City.

PubMed

Chen, Qun

2015-01-01

The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

49 CFR 605.11 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) That private school bus operators in the urban area are unable to provide adequate transportation, at a... 49 Transportation 7 2010-10-01 2010-10-01 false Exemptions. 605.11 Section 605.11 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

Optimation of Operation System Integration between Main and Feeder Public Transport (Case Study: Trans Jakarta-Kopaja Bus Services)

NASA Astrophysics Data System (ADS)

Miharja, M.; Priadi, Y. N.

2018-05-01

Promoting a better public transport is a key strategy to cope with urban transport problems which are mostly caused by a huge private vehicle usage. A better public transport service quality not only focuses on one type of public transport mode, but also concerns on inter modes service integration. Fragmented inter mode public transport service leads to a longer trip chain as well as average travel time which would result in its failure to compete with a private vehicle. This paper examines the optimation process of operation system integration between Trans Jakarta Bus as the main public transport mode and Kopaja Bus as feeder public transport service in Jakarta. Using scoring-interview method combined with standard parameters in operation system integration, this paper identifies the key factors that determine the success of the two public transport operation system integrations. The study found that some key integration parameters, such as the cancellation of “system setoran”, passenger get in-get out at official stop points, and systematic payment, positively contribute to a better service integration. However, some parameters such as fine system, time and changing point reliability, and information system reliability are among those which need improvement. These findings are very useful for the authority to set the right strategy to improve operation system integration between Trans Jakarta and Kopaja Bus services.

Pilot Evaluation of a Walking School Bus Program in a Low-Income Urban Community

USDA-ARS?s Scientific Manuscript database

To evaluate the impact of a walking school bus (WSB) program on the proportion of students walking to school in a low-income, urban neighborhood, we conducted a controlled, quasi-experimental trial in urban, socioeconomically disadvantaged, public elementary schools (one intervention and two control...

Pilot evaluation of a walking school bus program in a low-income, urban community

USDA-ARS?s Scientific Manuscript database

Our objective was to evaluate the impact of a walking school bus (WSB) program on student transport in a low-income, urban neighborhood. The design was a controlled, quasi-experimental trial with consecutive cross-sectional assessments. The setting was three urban, socioeconomically disadvantaged, p...

A summary of design, policies and operational characteristics for shared bicycle/bus lanes : [summary].

DOT National Transportation Integrated Search

2012-01-01

Traffic lanes set aside for the use of specific categories of vehicles are becoming more common, from dedicated bicycle lanes on urban roadways to managed lanes for carpools and other high occupancy vehicles on Floridas interstate highways. These ...

Comparative study of fuel cell, battery and hybrid buses for renewable energy constrained areas

NASA Astrophysics Data System (ADS)

Stempien, J. P.; Chan, S. H.

2017-02-01

Fuel cell- and battery-based public bus technologies are reviewed and compared for application in tropical urban areas. This paper scrutinizes the reported literature on fuel cell bus, fuel cell electric bus, battery electric bus, hybrid electric bus, internal combustion diesel bus and compressed natural gas bus. The comparison includes the capital and operating costs, fuel consumption and fuel cycle emissions. To the best of authors knowledge, this is the first study to holistically compare hydrogen and battery powered buses, which is the original contribution of this paper. Moreover, this is the first study to focus on supplying hydrogen and electricity from fossil resources, while including the associated emissions. The study shows that compressed natural gas and hybrid electric buses appear to be the cheapest options in terms of total cost of ownership, but they are unable to meet the EURO VI emissions' standard requirement. Only fuel cell based buses have the potential to achieve the emissions' standard when the fuel cycle based on fossil energy was considered. Fuel cell electric buses are identified as a technology allowing for the largest CO2 emission reduction, making ∼61% decrease in annual emissions possible.

Common Traffic Violations of Bus Drivers in Urban China: An Observational Study

PubMed Central

Yang, Rendong; Huang, Yuanxiu; Zhang, Lin; Ning, Peishan; Cheng, Xunjie; Schwebel, David C.

2015-01-01

Objective To report common traffic violations in bus drivers and the factors that influence those violations in urban China. Methods We conducted an observational study to record three types of traffic violations among bus drivers in Changsha City, China: illegal stopping at bus stations, violating traffic light signals, and distracted driving. The behaviors of bus drivers on 32 routes (20% of bus routes in the city) were observed. A two-level Poisson regression examined factors that predicted bus driver violations. Results The incidence of illegal stopping at bus stations was 20.2%. Illegal stopping was less frequent on weekends, sunny days, and at stations with cameras, with adjusted incidence rate ratios (IRRs) of 0.81, 0.65 and 0.89, respectively. The incidence of violating traffic light signals was 2.2%, and was lower on cloudy than sunny days (adjusted IRR: 0.60). The incidence of distracted driving was 3.3%. The incidence of distracted driving was less common on cloudy days, rainy or snowy days, and foggy/windy/dusty days compared to sunny days, with adjusted IRRs of 0.54, 0.55 and 0.07, respectively. Conclusion Traffic violations are common in bus drivers in urban China and they are associated with the date, weather, and presence of traffic cameras at bus station. Further studies are recommended to understand the behavioral mechanisms that may explain bus driver violations and to develop feasible prevention measures. PMID:26372105

Towards smart mobility in urban spaces: Bus tracking and information application

NASA Astrophysics Data System (ADS)

Yue, Wong Seng; Chye, Koh Keng; Hoy, Cheong Wan

2017-10-01

Smart city can be defined as an urban space with complete and advanced infrastructure, intelligent networks and platforms, with millions of sensors among which people themselves and their mobile devices. Urban mobility is one of the global smart city project which offers traffic management in real-time, management of passenger transport means, tracking applications and logistics, car sharing services, car park management and more smart mobility services. Due to the frustrated waiting time for the arrival of buses and the difficulty of accessing shuttle bus-related information in a one-stop centre, bus tracking and information application (BTA) is one the proposed solutions to solve the traffic problems in urban spaces. This paper is aimed to design and develop a bus tracking and information application in a selected city in Selangor state, Malaysia. Next, this application also provides an alternative to design public transport tracking and information application for the urban places in Malaysia. Furthermore, the application also provides a smart solution for the management of public infrastructures and urban facilities in Malaysia in future.

Computer Simulation of an Electric Trolley Bus

DOT National Transportation Integrated Search

1979-12-01

This report describes a computer model developed at the Transportation Systems Center (TSC) to simulate power/propulsion characteristics of an urban trolley bus. The work conducted in this area is sponsored by the Urban Mass Transportation Administra...

Bus transit operational efficiency resulting from passenger boardings at park-and-ride facilities.

DOT National Transportation Integrated Search

2016-08-01

In order to save time and money by not driving to an ultimate destination, some urban commuters drive themselves a few miles to specially designated parking lots built for transit customers and located where trains or buses stop. The focus of this pa...

A preliminary survey analysis of school shuttle bus system towards smart mobility solutions

NASA Astrophysics Data System (ADS)

Yue, Wong Seng; Hoy, Cheong Wan; Chye, Koh Keng

2017-10-01

Mobility and accessibility are crucial indicators of urban development. Public transport in the urban areas came into existence to fulfil transportation needs as well as mobility and accessibility demands. Ridership can be affected by the quality and quantity of transit service. However, technical improvements are needed for such as real-time bus information, controlling run time and headway delay. Thus, this paper is aimed to carry out a preliminary survey to determine the problems of school shuttle bus that faced by the students in a selected educational institution, their perceptions of using shuttle bus tracking and information mobile application and impacts of real-time information of public transits on bus ridership and towards smart mobility solutions. Efficient public transportation system needs further investigation about the role of mobile application for the bus tracking system in supporting smart mobility actions and real-time information. The proposed application also provides a smart solution for the management of public infrastructures and urban facilities in Malaysia in future. Eventually, this study opens an opportunity to improve Malaysian quality of life on the public value that created for the city as a whole.

Simulation of an Urban Battery Bus Vehicle

DOT National Transportation Integrated Search

1979-07-01

This report describes the computer simulation of a battery-powered bus as it traverses an arbitrary mission profile of specified acceleration, roadway grade, and headwind. The battery-bus system components comprise a DC shunt motor, solid-state power...

49 CFR 605.18 - Comments by private school bus operators.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Comments by private school bus operators. 605.18... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.18 Comments by private school bus operators. Private school bus operators may file written comments on an applicant's...

49 CFR 605.18 - Comments by private school bus operators.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Comments by private school bus operators. 605.18... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.18 Comments by private school bus operators. Private school bus operators may file written comments on an applicant's...

Air Conditioning Modifications for the GMC RTSII Series 01 Coach (Model TH 8201)

DOT National Transportation Integrated Search

1982-10-01

As part of its bus and paratransit technology research and development efforts, the Urban Mass Transportation Administration is conducting the Bus Subsystems Technology Project to help the transit bus industry solve serious equipment problems. The pr...

Connecticut DOT statewide bus system study : executive summary

DOT National Transportation Integrated Search

2000-07-01

The Connecticut Statewide Bus System Study has been undertaken to ensure that bus transit in Connecticut serves continuing needs in the most efficient manner possible. The Study has taken a comprehensive look at the state's twenty urban and rural tra...

Bus network redesign for inner southeast suburbs of Melbourne, Australia

NASA Astrophysics Data System (ADS)

Pandangwati, S. T.; Milyanab, N. A.

2017-06-01

Public transport is the most effective mode of transport in the era of climate change and oil depletion. It can address climate change issues by reducing urban greenhouse gas emission and oil consumption while at the same time improving mobility. However, many public transport networks are not effective and instead create high operating costs with low frequencies and occupancy. Melbourne is one example of a metropolitan area that faces this problem. Even though the city has well-integrated train and tram networks, Melbourne’s bus network still needs to be improved. This study used network planning approach to redesign the bus network in the City of Glen Eira, a Local Government Area (LGA) in the southeastern part of Metropolitan Melbourne. The study area is the area between Gardenvale North and Oakleigh Station, as well as between Caulfield and Patterson Stations. This area needs network improvement mainly because of the meandering bus routes that run within it. This study aims to provide recommendations for improving the performance of bus services by reducing meandering routes, improving transfer point design and implementing coordinated timetables. The recommendations were formulated based on a ‘ready-made’ concept to increase bus occupancy. This approach can be implemented in other cities with similar problems and characteristics including those in Indonesia.

49 CFR 605.19 - Approval of school bus operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Approval of school bus operations. 605.19 Section... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.19 Approval of school bus operations. (a) The Administrator will consider the comments filed by private school bus...

49 CFR 605.19 - Approval of school bus operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Approval of school bus operations. 605.19 Section... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.19 Approval of school bus operations. (a) The Administrator will consider the comments filed by private school bus...

Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

NASA Astrophysics Data System (ADS)

Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao

With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration.

Vehicle occupants' exposure to aromatic volatile organic compounds while commuting on an urban-suburban route in Korea.

PubMed

Jo, W K; Choi, S J

1996-08-01

This study identified in-auto and in-bus exposures to six selected aromatic volatile organic compounds (VOCs) for commutes on an urban-suburban route in Korea. A bus-service route was selected to include three segments of Taegu and one suburban segment (Hayang) to satisfy the criteria specified for this study. This study indicates that motor vehicle exhaust and evaporative emissions are major sources of both auto and bus occupants' exposures to aromatic VOCs in both Taegu and Hayang. A nonparametric statistical test (Wilcoxon test) showed that in-auto benzene levels were significantly different from in-bus benzene levels for both urban-segment and suburban-segment commutes. The test also showed that the benzene-level difference between urban-segment and suburban-segment commutes was significant for both autos and buses. An F-test showed the same statistical results for the comparison of the summed in-vehicle concentration of the six target VOCs (benzene, toluene, ethylbenzene, and o,m,p-xylenes) as those for the comparison of the in-vehicle benzene concentration. On the other hand, the in-vehicle benzene level only and the sum were not significantly different among the three urban-segment commutes and between the morning and evening commutes. The in-auto VOC concentrations were intermediate between the results for the Los Angeles and Boston. The in-bus VOC concentrations were about one-tenth of the Taipei, Taiwan results.

Analysis of a diesel-electric hybrid urban bus system

NASA Astrophysics Data System (ADS)

Marr, W. W.; Sekar, R. R.; Ahlheim, M. C.

A hybrid bus powered by a diesel engine and a battery pack was analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, were evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

An experimental study on real time bus arrival time prediction with GPS data

DOT National Transportation Integrated Search

2001-01-01

Bus headway in a rural area is usually much larger than that in an urban area. Providing real-time bus : arrival information could make the public transit system more user-friendly and thus enhance its : competitiveness among various transportation m...

An experimental study on real time bus arrival time prediction with GPS data

DOT National Transportation Integrated Search

1999-01-01

Bus headway in a rural area usually is much larger than that in an urban area. Providing real-time bus arrival information could make the public transit system more user-friendly and thus enhance its competitiveness among various transportation modes...

Complexity analysis on public transport networks of 97 large- and medium-sized cities in China

NASA Astrophysics Data System (ADS)

Tian, Zhanwei; Zhang, Zhuo; Wang, Hongfei; Ma, Li

2018-04-01

The traffic situation in Chinese urban areas is continuing to deteriorate. To make a better planning and designing of the public transport system, it is necessary to make profound research on the structure of urban public transport networks (PTNs). We investigate 97 large- and medium-sized cities’ PTNs in China, construct three types of network models — bus stop network, bus transit network and bus line network, then analyze the structural characteristics of them. It is revealed that bus stop network is small-world and scale-free, bus transit network and bus line network are both small-world. Betweenness centrality of each city’s PTN shows similar distribution pattern, although these networks’ size is various. When classifying cities according to the characteristics of PTNs or economic development level, the results are similar. It means that the development of cities’ economy and transport network has a strong correlation, PTN expands in a certain model with the development of economy.

Development of bus-stop time models in dense urban areas : a case study in Washington DC.

DOT National Transportation Integrated Search

2015-08-01

Bus transit reliability depends on several factors including the route of travel, traffic conditions, time of day, and conditions at : the bus stops along the route. The number of passengers alighting or boarding, fare payment method, dwell time (DT)...

Increasing the productivity of the nation's urban transportation infrastructure: Measures to increase transit use and carpooling. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kain, J.F.; Gittell, R.; Daniere, A.

1992-01-01

The report surveys the growing use of bus and carpool priority measures to increase the productivity of the nation's transportation infrastructure. While it identifies a wide variety of priority measures, the report principally focuses on the planning and operation of exclusive and shared busways and high occupancy vehicle (HOV) facilities. It presents a variety of case studies describing the implementation of busways and transitways. The document also compares the cost effectiveness of exclusive busways and bus-HOV facilities with the cost effectiveness of recently completed light and heavy rail lines. It also explores the options and problems in serving large downtownmore » areas.« less

A study of headway maintenance for bus routes : causes and effects of "bus bunching" in extensive and congested service areas.

DOT National Transportation Integrated Search

2012-07-01

A healthy and efficient public transit system is indispensable to reduce congestion, emissions, energy consumption, and car : dependency in urban areas. The objective of this research is to 1) develop methods to evaluate and visualize bus service rel...

A study on some urban bus transport networks

NASA Astrophysics Data System (ADS)

Chen, Yong-Zhou; Li, Nan; He, Da-Ren

2007-03-01

In this paper, we present the empirical investigation results on the urban bus transport networks (BTNs) of four major cities in China. In BTN, nodes are bus stops. Two nodes are connected by an edge when the stops are serviced by a common bus route. The empirical results show that the degree distributions of BTNs take exponential function forms. Other two statistical properties of BTNs are also considered, and they are suggested as the distributions of so-called “the number of stops in a bus route” (represented by S) and “the number of bus routes a stop joins” (by R). The distributions of R also show exponential function forms, while the distributions of S follow asymmetric, unimodal functions. To explain these empirical results and attempt to simulate a possible evolution process of BTN, we introduce a model by which the analytic and numerical result obtained agrees well with the empirical facts. Finally, we also discuss some other possible evolution cases, where the degree distribution shows a power law or an interpolation between the power law and the exponential decay.

Trends in bus transit operations, 1960-1974

DOT National Transportation Integrated Search

1977-01-01

This report analyzes the historical patterns of bus transit operations from 1960 to 1974 using data from 50 bus operations. Because of limitations on the available data, the analyzed data do not represent the universe of bus operations, nor is it a r...

COM-BUS : A Southern California Subscription Bus Service

DOT National Transportation Integrated Search

1977-05-01

The evolution and operations of the COM-BUS Subscription Commuter Bus Service are documented. COM-BUS is a privately owned organization operating at a profit without any form of subsidy. COM-BUS serves approximately 2,000 commuters per day on 47 rout...

Methanol use training manual

DOT National Transportation Integrated Search

1990-01-01

The Urban Mass Transportation Administration (UMTA) Alternative Fuels initiative (AFI) and the Environmental Protection Ageny (EPA) 1991 regulations on transit bus exhaust emissions has resulted in a number of alternative fueled transit bus demonstra...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

Determinants of spikes in ultrafine particle concentration whilst commuting by bus

NASA Astrophysics Data System (ADS)

Lim, Shanon; Dirks, Kim N.; Salmond, Jennifer A.; Xie, Shanju

2015-07-01

This paper examines concentration of ultrafine particles (UFPs) based on data collected using high-resolution UFP monitors whilst travelling by bus during rush hour along three different urban routes in Auckland, New Zealand. The factors influencing in-bus UFP concentration were assessed using a combination of spatial, statistical and GIS analysis techniques to determine both spatial and temporal variability. Results from 68 bus trips showed that concentrations varied more within a route than between on a given day, despite differences in urban morphology, land use and traffic densities between routes. A number of trips were characterised by periods of very rapid increases in UFPs (concentration 'spikes'), followed by slow declines. Trips which recorded at least one spike (an increase of greater than 10,000 pt/cm3) resulted in significantly higher mean concentrations. Spikes in UFPs were significantly more likely to occur when travelling at low speeds and when passengers were alighting and boarding at bus stops close to traffic light intersections.

Advanced Intelligent System Application to Load Forecasting and Control for Hybrid Electric Bus

NASA Technical Reports Server (NTRS)

Momoh, James; Chattopadhyay, Deb; Elfayoumy, Mahmoud

1996-01-01

The primary motivation for this research emanates from providing a decision support system to the electric bus operators in the municipal and urban localities which will guide the operators to maintain an optimal compromise among the noise level, pollution level, fuel usage etc. This study is backed up by our previous studies on study of battery characteristics, permanent magnet DC motor studies and electric traction motor size studies completed in the first year. The operator of the Hybrid Electric Car must determine optimal power management schedule to meet a given load demand for different weather and road conditions. The decision support system for the bus operator comprises three sub-tasks viz. forecast of the electrical load for the route to be traversed divided into specified time periods (few minutes); deriving an optimal 'plan' or 'preschedule' based on the load forecast for the entire time-horizon (i.e., for all time periods) ahead of time; and finally employing corrective control action to monitor and modify the optimal plan in real-time. A fully connected artificial neural network (ANN) model is developed for forecasting the kW requirement for hybrid electric bus based on inputs like climatic conditions, passenger load, road inclination, etc. The ANN model is trained using back-propagation algorithm employing improved optimization techniques like projected Lagrangian technique. The pre-scheduler is based on a Goal-Programming (GP) optimization model with noise, pollution and fuel usage as the three objectives. GP has the capability of analyzing the trade-off among the conflicting objectives and arriving at the optimal activity levels, e.g., throttle settings. The corrective control action or the third sub-task is formulated as an optimal control model with inputs from the real-time data base as well as the GP model to minimize the error (or deviation) from the optimal plan. These three activities linked with the ANN forecaster proving the output to the GP model which in turn produces the pre-schedule of the optimal control model. Some preliminary results based on a hypothetical test case will be presented for the load forecasting module. The computer codes for the three modules will be made available fe adoption by bus operating agencies. Sample results will be provided using these models. The software will be a useful tool for supporting the control systems for the Electric Bus project of NASA.

Liquefied natural gas fuel use : basic training manual

DOT National Transportation Integrated Search

1994-05-01

The Urban Mass Transportation Administration's Alternative Fuel Initiative and the Environmental Protection Agency's 1991 regulations on transit bus exhaust emissions has resulted in a number of alternative fueled transit bus research and demonstrati...

Compressed natural gas fuel use training manual

DOT National Transportation Integrated Search

1992-09-01

The Urban Mass Transportation Administration (UMTA) Alternative Fuel Initiative and the Environmental Protection Agency (EPA) 1991 regulations on transit bus exhaust emissions has resulted in a number of alternative fueled transit bus demonstrations....

Analysis of Florida transit bus accidents

DOT National Transportation Integrated Search

2001-06-01

Through its National Center for Transit Research, and under contract with the Florida Department of Transportation, the Center for Urban Transportation Research was tasked with reviewing a sample of transit bus crash occurrence data from selected Flo...

Analysis of Florida transit bus crashes

DOT National Transportation Integrated Search

2001-06-01

Through its National Center for Transit Research, and under contract with the Florida Department of Transportation, the Center for Urban Transportation Research was tasked with reviewing a sample of transit bus crash occurrence data from selected Flo...

Hybrid Propulsion Technologies for Urban Bus Transit

DOT National Transportation Integrated Search

1984-11-01

Information on hybrid propulsion technologies is presented to increase the transit community's awareness and understanding of bus propulsion designs that offer extended use capability for trolley-emergency, short-range, and back-up propulsion for tro...

Emission inventory estimation of an intercity bus terminal.

PubMed

Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

2016-06-01

Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

Montana intercity bus service study.

DOT National Transportation Integrated Search

2011-12-01

Intercity bus service funding from the Federal Transit Administration (FTAs) Section 5311(f) program is a part : of the larger 5311 program known as Formula Grants for Other than Urbanized Areas. The S.5311(f), requires : that 15% of the total 531...

Bus Rapid Transit system’s influence on urban development: An inquiry to Boston and Seoul BRT systems’ technical characteristics

NASA Astrophysics Data System (ADS)

Prayogi, Lutfi

2018-03-01

This article explores the relation between bus rapid transit (BRT) system and urban development. This article was written through a multi-staged comprehensive literature review. It includes a general overview of widely acknowledged BRT technical characteristics. It explains the approach taken in understanding the relation between BRT system provision and urban development around the system. Findings regarding the influence of Boston Silver Line 4 and 5 and Seoul BRT systems on urban development around the systems are quoted and used as case studies. Investigation on the technical characteristics of Boston SL4/5 and Seoul BRT systems are provided. This article shows that the two BRT systems that influence urban development around the systems have technical characteristics that enable the BRT systems to have high performance. However, while the quoted BRT systems can influence urban development, they have significantly different performance.

Bus safety study : a report to Congress.

DOT National Transportation Integrated Search

2013-11-01

Section 20021(b) of the Moving Ahead for Progress for the 21st Century (MAP-21) legislation requires the Secretary of Transportation : to submit a report of the results of a Bus Safety Study to the Committee on Banking, Housing, and Urban Affai...

Revealing Spatial Variation and Correlation of Urban Travels from Big Trajectory Data

NASA Astrophysics Data System (ADS)

Li, X.; Tu, W.; Shen, S.; Yue, Y.; Luo, N.; Li, Q.

2017-09-01

With the development of information and communication technology, spatial-temporal data that contain rich human mobility information are growing rapidly. However, the consistency of multi-mode human travel behind multi-source spatial-temporal data is not clear. To this aim, we utilized a week of taxies' and buses' GPS trajectory data and smart card data in Shenzhen, China to extract city-wide travel information of taxi, bus and metro and tested the correlation of multi-mode travel characteristics. Both the global correlation and local correlation of typical travel indicator were examined. The results show that: (1) Significant differences exist in of urban multi-mode travels. The correlation between bus travels and taxi travels, metro travel and taxi travels are globally low but locally high. (2) There are spatial differences of the correlation relationship between bus, metro and taxi travel. These findings help us understanding urban travels deeply therefore facilitate both the transport policy making and human-space interaction research.

Motorist Comprehension of Florida's School Bus Stop Law and School Bus Signalization Devices

DOT National Transportation Integrated Search

1997-06-01

In May 1995, the Center for Urban Transportation Research (CUTR) conducted a study on behalf of the Florida Department of Education (DOE) that investigated the frequency and extent with which drivers in Florida were illegally passing stopped school b...

Cops, cameras, and enclosures : a synthesis of the effectiveness of methods to provide enhanced security for bus operators

DOT National Transportation Integrated Search

2001-05-31

The safety of operators and passengers is a primary concern of transit systems and has become an increasingly important issue to transit bus operators themselves. Many transit agencies have experienced incidents of assaults against their bus operator...

JPRS Report, Near East and South Asia, Iran

DTIC Science & Technology

1992-08-14

rates that make the export of goods to distant markets possible. C. More attention to the importance of advertisement in the development of goods such...The design and construction of this bus were also approved by Mercedes Benz . Zaka’i said the capacity of the new Iranian-made urban buses is 105...achieved. Despite all the problems that Iranian exports have faced in foreign markets , the operation of the export sector in the first three years

Genetic Algorithm for Multiple Bus Line Coordination on Urban Arterial

PubMed Central

Yang, Zhen; Wang, Wei; Chen, Shuyan; Ding, Haoyang; Li, Xiaowei

2015-01-01

Bus travel time on road section is defined and analyzed with the effect of multiple bus lines. An analytical model is formulated to calculate the total red time a bus encounters when travelling along the arterial. Genetic algorithm is used to optimize the offset scheme of traffic signals to minimize the total red time that all bus lines encounter in two directions of the arterial. The model and algorithm are applied to the major part of Zhongshan North Street in the city of Nanjing. The results show that the methods in this paper can reduce total red time of all the bus lines by 31.9% on the object arterial and thus improve the traffic efficiency of the whole arterial and promote public transport priority. PMID:25663837

32 CFR 935.138 - Motor bus operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

32 CFR 935.138 - Motor bus operation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

Madison Avenue Dual Exclusive Bus Lane Demonstration - New York City

DOT National Transportation Integrated Search

1984-05-01

In May 1981, the New York City Department of Transportation implemented a dual exclusive bus lane facility on Madison Avenue in midtown Manhattan, between 42nd and 59th Streets. The project was sponsored for one year as a demonstration by the Urban M...

Magnitude and correlates of bird collisions at glass bus shelters in an urban landscape.

PubMed

Barton, Christine M; Riding, Corey S; Loss, Scott R

2017-01-01

Wildlife residing in urban landscapes face many human-related threats to their survival. For birds, collision with glass on manmade structures has been identified as a major hazard, causing hundreds of millions of avian fatalities in North America every year. Although research has investigated factors associated with bird-glass collision mortality at buildings, no prior studies have focused on bird fatalities at glass-walled bus shelters. Our objectives in this study were to describe the magnitude of bird-bus shelter collisions in the city of Stillwater, Oklahoma and assess potential predictors of collision risk, including characteristics of shelters (glass area) and surrounding land cover (e.g., vegetative features). We surveyed for bird carcasses and indirect collision evidence at 18 bus shelters over a five-month period. Linear regression and model selection results revealed that the amount of glass on shelters and the area of lawn within 50 m of shelters were both positively related to fatal bird collisions; glass area was also positively associated with observations of collision evidence on glass surfaces. After accounting for scavenger removal of carcasses, we estimate that a minimum of 34 birds are killed each year between May and September by collision with the 36 bus shelters in the city of Stillwater. While our study provides an initial look at bird fatalities at bus shelters, additional research is needed to generate a large-scale estimate of collision mortality and to assess species composition of fatalities at a national scale. Designing new bus shelters to include less glass and retrofitting existing shelters to increase visibility of glass to birds will likely reduce fatal bird collisions at bus shelters and thus reduce the cumulative magnitude of anthropogenic impacts to birds in cities.

Policy evaluation for a bus-based transit system: the case study of Busan, Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lew, K.S.

This study considers a quite specific set of dimensions of transit evaluation as a comprehensive management-strategy approach for addressing the ongoing problems of urban public transit systems and apply them in a case study. With increasing difficulties in providing effective public transportation, attention in this study was placed on providing for the movement of people in an efficient and equitable manner. This study was therefore concerned with just identifying and evaluating policy options that are feasible within the socio-economic and political context of the Busan metropolitan area and, in particular, how the criteria of efficiency and equity can best bemore » achieved by implementing transit policy alternatives. In the absence of long-run major public investment in urban transportation, the criteria of both efficiency and equity can only be furthered through managerial strategies applied within a systematic evaluative framework. By emphasizing the planning, operational, and managerial considerations of fixed-route bus transit in Busan, it has been acknowledged that efficient and equitable public transportation can be provided through a variety of social, economic, political, and institutional arrangements that are possible to apply from a policy viewpoint in the immediate future.« less

Emission comparison of urban bus engine fueled with diesel oil and 'biodiesel' blend.

PubMed

Turrio-Baldassarri, Luigi; Battistelli, Chiara L; Conti, Luigi; Crebelli, Riccardo; De Berardis, Barbara; Iamiceli, Anna Laura; Gambino, Michele; Iannaccone, Sabato

2004-07-05

The chemical and toxicological characteristics of emissions from an urban bus engine fueled with diesel and biodiesel blend were studied. Exhaust gases were produced by a turbocharged EURO 2 heavy-duty diesel engine, operating in steady-state conditions on the European test 13 mode cycle (ECE R49). Regulated and unregulated pollutants, such as carcinogenic polycyclic aromatic hydrocarbons (PAHs) and nitrated derivatives (nitro-PAHs), carbonyl compounds and light aromatic hydrocarbons were quantified. Mutagenicity of the emissions was evaluated by the Salmonella typhimurium/mammalian microsome assay. The effect of the fuels under study on the size distribution of particulate matter (PM) was also evaluated. The use of biodiesel blend seems to result in small reductions of emissions of most of the aromatic and polyaromatic compounds; these differences, however, have no statistical significance at 95% confidence level. Formaldehyde, on the other hand, has a statistically significant increase of 18% with biodiesel blend. In vitro toxicological assays show an overall similar mutagenic potency and genotoxic profile for diesel and biodiesel blend emissions. The electron microscopy analysis indicates that PM for both fuels has the same chemical composition, morphology, shape and granulometric spectrum, with most of the particles in the range 0.06-0.3 microm.

Transit vehicle-to-infrastructure (V2I) applications : near term research and development. Transit bus-pedestrian/cyclist crossing safety application : operational concept.

DOT National Transportation Integrated Search

2013-11-01

This document serves as an Operational Concept for the Transit Bus-Pedestrian/Cyclist Crossing Safety application. The purpose of this document is to provide an operational description of how the Transit Bus-Pedestrian/Cyclist Crossing Safety W...

Pilot survey of subway and bus stop noise levels.

PubMed

Gershon, Robyn R M; Neitzel, Richard; Barrera, Marissa A; Akram, Muhammad

2006-09-01

Excessive noise exposure is a serious global urban health problem, adversely affecting millions of people. One often cited source of urban noise is mass transit, particularly subway systems. As a first step in determining risk within this context, we recently conducted an environmental survey of noise levels of the New York City transit system. Over 90 noise measurements were made using a sound level meter. Average and maximum noise levels were measured on subway platforms, and maximum levels were measured inside subway cars and at several bus stops for comparison purposes. The average noise level measured on the subway platforms was 86 +/- 4 dBA (decibel-A weighting). Maximum levels of 106, 112, and 89 dBA were measured on subway platforms, inside subway cars, and at bus stops, respectively. These results indicate that noise levels in subway and bus stop environments have the potential to exceed recommended exposure guidelines from the World Health Organization (WHO) and U.S. Environmental Protection Agency (EPA), given sufficient exposure duration. Risk reduction strategies following the standard hierarchy of control measures should be applied, where feasible, to reduce subway noise exposure.

Trace Metals in Urban Stormwater Runoff and their Management

NASA Astrophysics Data System (ADS)

Li, T.; Hall, K.; Li, L. Y.; Schreier, H.

2009-04-01

In past decades, due to the rapid urbanization, land development has replaced forests, fields and meadows with impervious surfaces such as roofs, parking lots and roads, significantly affecting watershed quality and having an impact on aquatic systems. In this study, non-point source pollution from a diesel bus loop was assessed for the extent of trace metal contamination of Cu, Mn, Fe, and Zn in the storm water runoff. The study was carried out at the University of British Columbia (UBC) in the Greater Vancouver Regional District (GVRD) of British Columbia, Canada. Fifteen storm events were monitored at 3 sites from the diesel bus loop to determine spatial and temporal variations of dissolved and total metal concentrations in the storm water runoff. The dissolved metal concentrations were compared with the provincial government discharge criteria and the bus loop storm water quality was also compared with previous studies conducted across the GVRD urban area. To prevent storm water with hazardous levels of contaminants from being discharged into the urban drainage system, a storm water catch basin filter was installed and evaluated for its efficiency of contaminants removal. The perlite filter media adsorption capacities for the trace metals, oil and grease were studied for better maintenance of the catch basin filter. Dissolved copper exceeded the discharge criteria limit in 2 out of 15 cases, whereas dissolved zinc exceeded the criteria in 4 out of 15 cases, and dissolved manganese was below the criteria in all of the events sampled. Dissolved Cu and Zn accounted for 36 and 45% of the total concentration, whereas Mn and Fe only accounted for 20 and 4% of their total concentration, respectively. Since they are more mobile and have higher bioaccumulation potentials, Zn and Cu are considered to be more hazardous to the aquatic environment than Fe and Mn. With high imperviousness (100%) and intensive traffic at the UBC diesel bus loop, trace metal concentrations were 3, 0.7, 9, and 3.2 times higher than the GVRD urban area limits for Cu, Mn, Fe, and Zn, respectively. The filter showed high and stable capture efficiencies in total metals (Cu 62%, Mn 75%, Fe 83%, Zn 62%), dissolved metals (Cu 39%, Mn 37%, Fe 47%, Zn 32%), turbidity (72%), and suspended solids (74%) removal during the first month of operation. After that, there was gradual degradation. The catch basin filter performance improved significantly for the suspended solids and total metal removal after cleaning. However, the perlite filter medium showed poor performance for dissolved metal removal in the second study period. Based on the findings, a catch basin filter is effective in storm water management to control suspended solids loading from storm water runoff.

Spatial analysis of bus transport networks using network theory

NASA Astrophysics Data System (ADS)

Shanmukhappa, Tanuja; Ho, Ivan Wang-Hei; Tse, Chi Kong

2018-07-01

In this paper, we analyze the bus transport network (BTN) structure considering the spatial embedding of the network for three cities, namely, Hong Kong (HK), London (LD), and Bengaluru (BL). We propose a novel approach called supernode graph structuring for modeling the bus transport network. A static demand estimation procedure is proposed to assign the node weights by considering the points of interests (POIs) and the population distribution in the city over various localized zones. In addition, the end-to-end delay is proposed as a parameter to measure the topological efficiency of the bus networks instead of the shortest distance measure used in previous works. With the aid of supernode graph representation, important network parameters are analyzed for the directed, weighted and geo-referenced bus transport networks. It is observed that the supernode concept has significant advantage in analyzing the inherent topological behavior. For instance, the scale-free and small-world behavior becomes evident with supernode representation as compared to conventional or regular graph representation for the Hong Kong network. Significant improvement in clustering, reduction in path length, and increase in centrality values are observed in all the three networks with supernode representation. The correlation between topologically central nodes and the geographically central nodes reveals the interesting fact that the proposed static demand estimation method for assigning node weights aids in better identifying the geographically significant nodes in the network. The impact of these geographically significant nodes on the local traffic behavior is demonstrated by simulation using the SUMO (Simulation of Urban Mobility) tool which is also supported by real-world empirical data, and our results indicate that the traffic speed around a particular bus stop can reach a jammed state from a free flow state due to the presence of these geographically important nodes. A comparison of the simulation and the empirical data provides useful information on how bus operators can better plan their routes and deploy stops considering the geographically significant nodes.

Myocardial infarction among male bus, taxi, and lorry drivers in middle Sweden.

PubMed Central

Gustavsson, P; Alfredsson, L; Brunnberg, H; Hammar, N; Jakobsson, R; Reuterwall, C; Ostlin, P

1996-01-01

OBJECTIVES: The aim of the present case-referent study was to investigate the incidence of myocardial infarction among male professional drivers, taking the type of vehicles and area of residence into account. METHODS: The study base comprised all men aged 30-74 in five counties in middle Sweden during 1976-81 or 1976-84. Incident cases of the first episode of myocardial infarction were identified from registers of hospital admissions and causes of deaths. Referents were selected randomly from the study base. Information about occupation was obtained from the national censuses in 1970 and 1975. The possible impact from tobacco smoking and overweight were evaluated by simulations in combination with indirect data on these factors. RESULTS: The incidence of myocardial infarction was increased among bus drivers in Stockholm (relative risk (RR) = 1.53, 95% confidence interval (95% CI) 1.15-2.05), and among taxi drivers both in Stockholm (RR 1.65, 95% CI 1.30-2.11) and in the surrounding rural counties (RR 1.82, 95% CI 1.17-2.82). A smaller increase was found among long distance lorry drivers, whereas the relative risk among short distance lorry drivers was close to unity. Indirect comparisons make it unlikely that the excess among bus drivers in Stockholm could be explained by uncontrolled confounding from tobacco smoking or overweight. A very high proportion (more than 80%) of urban bus drivers in Sweden report a combination of high psychological demands and low control at work. CONCLUSIONS: Different types of drivers are at different risk of myocardial infarction. Bus drivers in urban areas seem to be at an increased risk, which is unlikely to be explained by uncontrolled confounding from tobacco smoking or overweight. Psychosocial work conditions may play a part in the increased incidence of myocardial infarction among urban bus drivers and should be investigated further. PMID:8664960

Intelligent lightening system of urban and rural road traffic based on pyroelectric infrared detector

NASA Astrophysics Data System (ADS)

Miao, Man-Xiang

2007-12-01

By using the photo-voltage characteristics of pyroelectric infrared detector to fulfill signal acquisition, the detecting signal is processed with the core of a single chip microprocessor AT89C51. AT89C51 controls the CAN bus controller SJA1000/transceiver 82C250 to structure CAN bus communication system to transmit data through serial interface MAX232 connected with PC. The intelligent lightening system of urban and rural road traffic was carried out. In this paper, its construction and part's methods of hardware and software design were introduced in detail.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

DOT National Transportation Integrated Search

2008-10-16

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

Bus Lifecycle Cost Model for Federal Land Management Agencies.

DOT National Transportation Integrated Search

2011-09-30

The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

Shuttle bus services quality assessment Tangerang Selatan toward smart city

NASA Astrophysics Data System (ADS)

Fassa, Ferdinand; Sitorus, Fredy Jhon Philip; Adikesuma, Tri Nugraha

2017-11-01

Around the world, shuttle bus operation played the significant role to accommodate transportation for commuting bus passengers. Shuttle Bus services in cities are provided by various bus agencies with kinds of own specific purposes. For instance, at Tangerang Selatan, Indonesia, it was said that shuttle bus In Trans Bintaro is run and operated by private bus companies hire by Bintaro developer. The aim of this research is to identify factors of satisfaction of shuttle bus service in Kota Tangerang Selatan, Indonesia. Several factors are used to analyze sums of 20 parameters performance indicators of Shuttle Bus. A face to face interview using a questionnaire (N=200) was used to collect data on October and March 2017. Likert and diagram Cartesian were used to model the all the parameters. This research succeeded in finding some categories of Shuttle bus service attributes such as accessibility, comfort, and safety. Users agreed that eight indicators in shuttle bus have the excellent achievement, while three indicators on performance remain low and should receive more attention especially punctuality of the bus.

[Work-related stress and psychological distress assessment in urban and suburban public transportation companies].

PubMed

Romeo, L; Lazzarini, G; Farisè, E; Quintarelli, E; Riolfi, A; Perbellini, L

2012-01-01

The risk of work-related stress has been determined in bus drivers and workers employed in the service department of two urban and suburban public transportation companies. The INAIL evaluation method (Check list and HSE indicator tool) was used. The GHQ-12 questionnaire, which is widely used to assess the level of psychological distress, was also employed. 81.9% of workers involved in the survey answered both the HSE indicator tool and the GHQ-12 questionnaire. The Check list evaluation showed an increase in quantifiable company stress indicators while close examination using the HSE indicator tool demonstrated critical situations for all the subscales, with the control subscales more problematic in bus drivers. The demand, manager's support, relationships and change subscales were most associated with psychological distress in bus drivers, while relationships, role, change and demand subscales were negatively related in workers of the service department.

49 CFR 37.169 - Interim requirements for over-the-road bus service operated by private entities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Interim requirements for over-the-road bus service... Interim requirements for over-the-road bus service operated by private entities. (a) Private entities operating over-the-road buses, in addition to compliance with other applicable provisions of this part...

Modeling the effect of bus stops on capacity of curb lane

NASA Astrophysics Data System (ADS)

Luo, Qingyu; Zheng, Tianyao; Wu, Wenjing; Jia, Hongfei; Li, Jin

With the increase of buses and bus lines, a negative effect on road section capacity is made by the prolonged delay and queuing time at bus stops. However, existing methods of measuring the negative effect pay little attention to different bus stop types in the curb lanes. This paper uses Gap theory and Queuing theory to build models for effect-time and potential capacity in different conditions, including curbside bus stops, bus bays with overflow and bus bays without overflow. In order to make the effect-time models accurate and reliable, two types of probabilities are introduced. One is the probability that the dwell time is less than the headway of curb lane at curbside bus stops; the other is the overflow probability at bus bays. Based on the fundamental road capacity model and effect-time models, potential capacity models of curb lane are designed. The new models are calibrated by the survey data from Changchun City, and verified by the simulation software of VISSIM. Furthermore, with different arrival rates of vehicles, the setting conditions of bus stops are researched. Results show that the potential capacity models have high precision. They can offer a reference for recognizing the effect of bus stops on the capacity of curb lane, which can provide a basis for planning, design and management of urban roads and bus stops.

Rethinking passive transport: bus fare exemptions and young people's wellbeing.

PubMed

Jones, Alasdair; Steinbach, Rebecca; Roberts, Helen; Goodman, Anna; Green, Judith

2012-05-01

Much recent public health research has emphasised the health impacts for young people of 'active travel' modes, typically defined as walking and cycling. Less research has focused on public transport modes. Drawing on qualitative data, we examine the links between bus travel and wellbeing in London, where young people currently have free bus travel. Our findings indicate that bus travel can be both a physically and socially active experience for young people. We suggest a more nuanced understanding of 'active travel' is now needed, alongside greater attention to urban public transport networks as key sites that impact on important determinants of wellbeing such as independent mobility and social inclusion. Copyright © 2012 Elsevier Ltd. All rights reserved.

Asymptotically zero power charge-recycling bus architecture for battery-operated ultrahigh data rate ULSI's

NASA Astrophysics Data System (ADS)

Yamauchi, Hiroyuki; Akamatsu, Hironori; Fujita, Tsutomu

1995-04-01

An asymptotically zero power charge recycling bus (CRB) architecture, featuring virtual stacking of the individual bus-capacitance into a series configuration between supply voltage and ground, has been proposed. This CRB architecture makes it possible to reduce not only each bus-swing but also a total equivalent bus-capacitance of the ultramultibit buses running in parallel. The voltage swing of each bus is given by the recycled charge-supplying from the upper adjacent bus capacitance, instead of the power line. The dramatical power reduction was verified by the simulated and measured data. According to these data, the ultrahigh data rate of 25.6 Gb/s can be achieved while maintaining the power dissipation to be less than 100 mW, which corresponds to less than 10% that of the previously reported 0.9 V suppressed bus-swing scheme, at V(sub cc) = 3.6 V for the bus width of 512 b with the bus-capacitance of 14 pF per bit operating at 50 MHz.

Integer programming model for optimizing bus timetable using genetic algorithm

NASA Astrophysics Data System (ADS)

Wihartiko, F. D.; Buono, A.; Silalahi, B. P.

2017-01-01

Bus timetable gave an information for passengers to ensure the availability of bus services. Timetable optimal condition happened when bus trips frequency could adapt and suit with passenger demand. In the peak time, the number of bus trips would be larger than the off-peak time. If the number of bus trips were more frequent than the optimal condition, it would make a high operating cost for bus operator. Conversely, if the number of trip was less than optimal condition, it would make a bad quality service for passengers. In this paper, the bus timetabling problem would be solved by integer programming model with modified genetic algorithm. Modification was placed in the chromosomes design, initial population recovery technique, chromosomes reconstruction and chromosomes extermination on specific generation. The result of this model gave the optimal solution with accuracy 99.1%.

Planning criteria for express bus-fringe parking operations : volume I of express bus-fringe parking planning methodology.

DOT National Transportation Integrated Search

1975-01-01

Tripmaker reactions to two recent express bus-fringe parking operations in Richmond and Norfolk-Virginia Beach Virginia are examined. This travel behavior's interpreted to establish planning and design guidelines for locating and designing fringe lot...

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, L.; Chandler, K.

2013-01-01

SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and helpmore » determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.« less

A new bus lane on urban expressway with no-bay bus stop

NASA Astrophysics Data System (ADS)

Tian, Zhao; Jia, Limin

2016-01-01

The sharp increase in residents and vehicles causes heavy traffic pressure in many cities. To ease traffic congestion, it has been the common sense that we should develop public transit system. The priority of the bus appears particularly necessary with the rapid development of the public transport system. The bus lane is an important embodiment of the bus priority. Focusing on the problem of the unreasonable dedicated bus lane (DBL) under the lower ratio of buses, this paper proposed a new bus lane with limited physical length. And this bus lane can reduce the lane-changing conflict caused by the buses and cars running on roads without bus lanes. Based on the cellular automata (CA) traffic flow model and the lane-changing behavior of the vehicle including the optional lane-changing and the mandatory lane-changing, a three-lane traffic model with an isolated no-bay bus stop is proposed. The ordinary three-lane traffic without a bus lane and the cases of traffic with a DBL or the proposed bus lane are simulated, and the comparisons in the form of the fundamental diagrams are made among them. It is shown that the no-bay bus stop can act as a bottleneck on the traffic flow because of the mandatory lane-changing behavior. Under a certain ratio of the bus number to the total vehicles number, (1) the traffic with the proposed bus lane has less lane-changing conflict and can provide higher traffic capacity than the ordinary traffic without a bus lane, (2) compared with the DBL, the proposed bus lane is advantageous in easing congestion on the ordinary lanes when the traffic flow is high and can avoid unreasonable allocation of the road resources.

78 FR 719 - California State Motor Vehicle Pollution Control Standards; Urban Buses; Request for Waiver of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-04

.... Collectively, the five rulemakings elevated the stringency of exhaust emission standards and test procedures... Act for the emission standards and related test procedures contained in its urban bus regulations, as... Standards; Urban Buses; Request for Waiver of Preemption; Opportunity for Public Hearing and Comment AGENCY...

Texas Hydrogen Highway Fuel Cell Hybrid Bus and Fueling Infrastructure Technology Showcase - Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hitchcock, David

The Texas Hydrogen Highway project has showcased a hydrogen fuel cell transit bus and hydrogen fueling infrastructure that was designed and built through previous support from various public and private sector entities. The aim of this project has been to increase awareness among transit agencies and other public entities on these transportation technologies, and to place such technologies into commercial applications, such as a public transit agency. The initial project concept developed in 2004 was to show that a skid-mounted, fully-integrated, factory-built and tested hydrogen fueling station could be used to simplify the design, and lower the cost of fuelingmore » infrastructure for fuel cell vehicles. The approach was to design, engineer, build, and test the integrated fueling station at the factory then install it at a site that offered educational and technical resources and provide an opportunity to showcase both the fueling station and advanced hydrogen vehicles. The two primary technology components include: Hydrogen Fueling Station: The hydrogen fueling infrastructure was designed and built by Gas Technology Institute primarily through a funding grant from the Texas Commission on Environmental Quality. It includes hydrogen production, clean-up, compression, storage, and dispensing. The station consists of a steam methane reformer, gas clean-up system, gas compressor and 48 kilograms of hydrogen storage capacity for dispensing at 5000 psig. The station is skid-mounted for easy installation and can be relocated if needed. It includes a dispenser that is designed to provide temperaturecompensated fills using a control algorithm. The total station daily capacity is approximately 50 kilograms. Fuel Cell Bus: The transit passenger bus built by Ebus, a company located in Downey, CA, was commissioned and acquired by GTI prior to this project. It is a fuel cell plug-in hybrid electric vehicle which is ADA compliant, has air conditioning sufficient for Texas operations, and regenerative braking for battery charging. It uses a 19.3 kW Ballard PEM fuel cell, will store 12.6 kg of hydrogen at 350 Bar, and includes a 60 kWh battery storage system. The objectives of the project included the following: (a) To advance commercialization of hydrogen-powered transit buses and supporting infrastructure; (b) To provide public outreach and education by showcasing the operation of a 22-foot fuel cell hybrid shuttle bus and Texas first hydrogen fueling infrastructure; and (c) To showcase operation of zero-emissions vehicle for potential transit applications. As mentioned above, the project successfully demonstrated an early vehicle technology, the Ebus plug-in hybrid fuel cell bus, and that success has led to the acquisition of a more advanced vehicle that can take advantage of the same fueling infrastructure. Needed hydrogen station improvements have been identified that will enhance the capabilities of the fueling infrastructure to serve the new bus and to meet the transit agency needs. Over the course of this project, public officials, local government staff, and transit operators were engaged in outreach and education activities that acquainted them with the real world operation of a fuel cell bus and fueling infrastructure. Transit staff members in the Dallas/Ft. Worth region were invited to a workshop in Arlington, Texas at the North Central Texas Council of Governments to participate in a workshop on hydrogen and fuel cells, and to see the fuel cell bus in operation. The bus was trucked to the meeting for this purpose so that participants could see and ride the bus. Austin area transit staff members visited the fueling site in Austin to be briefed on the bus and to participate in a fueling demonstration. This led to further meetings to determine how a fuel cell bus and fueling station could be deployed at Capital Metro Transit. Target urban regions that expressed additional interest during the project in response to the outreach meetings and showcase events include San Antonio and Austin, Texas. In summary, the project objectives were achieved in the following ways: Through presentations and papers provided to a variety of audiences in multiple venues, the project team fulfilled its goal of providing education and outreach on hydrogen technology to statewide audiences. The project team generated interest that exists well beyond the completion of the project, and indeed, helped to generate financial support for a subsequent hydrogen vehicle project in Austin. The University of Texas, Center for ElectroMechanics operated the fuel cell-electric Ebus vehicle for over 13,000 miles in Austin, Texas in a variety of routes and loading configurations. The project took advantage of prior efforts that created a hydrogen fueling station and fuel cell electric-hybrid bus and continued to verify their technical foundation, while informing and educating potential future users of how these technologies work.« less

Combined Quarterly Technical Report Number 25. SATNET Development and Operation, Pluribus Satellite IMP Development, Remote Site Maintenance, Internet Operations and Maintenance, Mobile Access Terminal Network, TCP for the HP3000, TCP for VAX-UNIX.

DTIC Science & Technology

1982-05-01

the F-Bus. The two possible SuperSUE I Pollers, SSPE and SSPF, are on the E and F buses, respectively. P13 is the P13 Poller. A PSAT will have at... SSPE and SSPF are again the two possible SuperSUE Pollers. HPOL is an abbrevation for the HINPOL and HOUTPOL routines. -44- jReport No. 5003 Bolt...I IS I E-Bus,F-Bus I E-Bus Only I F-Bus only I s -- - - - - - - - - - - - - - - - - -- - - - - - P E-Bus ISMIE/ SSPE ISMIE/ SSPE ISMIF/SSPF IF-Bu3

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

Pilot Survey of Subway and Bus Stop Noise Levels

PubMed Central

Neitzel, Richard; Barrera, Marissa A.; Akram, Muhammad

2006-01-01

Excessive noise exposure is a serious global urban health problem, adversely affecting millions of people. One often cited source of urban noise is mass transit, particularly subway systems. As a first step in determining risk within this context, we recently conducted an environmental survey of noise levels of the New York City transit system. Over 90 noise measurements were made using a sound level meter. Average and maximum noise levels were measured on subway platforms, and maximum levels were measured inside subway cars and at several bus stops for comparison purposes. The average noise level measured on the subway platforms was 86 ± 4 dBA (decibel-A weighting). Maximum levels of 106, 112, and 89 dBA were measured on subway platforms, inside subway cars, and at bus stops, respectively. These results indicate that noise levels in subway and bus stop environments have the potential to exceed recommended exposure guidelines from the World Health Organization (WHO) and U.S. Environmental Protection Agency (EPA), given sufficient exposure duration. Risk reduction strategies following the standard hierarchy of control measures should be applied, where feasible, to reduce subway noise exposure. PMID:16802179

Effect of Torsional Fastener Resistance on the Lateral Response of a Rail-Tie Structure

DOT National Transportation Integrated Search

1978-09-01

This report describes the results of a Transportation Systems Center investigation conducted under Urban Mass Transportation Administration sponsorship, of the practicality of a flywheel/diesel hybrid power drive for urban transit bus propulsion. The...

Potential Influence of Metro on Bus: A Case Study

NASA Astrophysics Data System (ADS)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-03-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare-difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

Potential Influence of Metro on Bus: A Case Study

NASA Astrophysics Data System (ADS)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-06-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare- difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

Electric School Bus Testing | Transportation Research | NREL

Science.gov Websites

Electric School Bus Evaluation Electric School Bus Evaluation Photo of children boarding school bus . NREL is evaluating the performance of electric and conventional school buses operated by two California school districts. Photo courtesy of School Bus Fleet Magazine NREL is evaluating the in-service

Robust planning of dynamic wireless charging infrastructure for battery electric buses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Zhaocai; Song, Ziqi

Battery electric buses with zero tailpipe emissions have great potential in improving environmental sustainability and livability of urban areas. However, the problems of high cost and limited range associated with on-board batteries have substantially limited the popularity of battery electric buses. The technology of dynamic wireless power transfer (DWPT), which provides bus operators with the ability to charge buses while in motion, may be able to effectively alleviate the drawbacks of electric buses. In this paper, we address the problem of simultaneously selecting the optimal location of the DWPT facilities and designing the optimal battery sizes of electric buses formore » a DWPT electric bus system. The problem is first constructed as a deterministic model in which the uncertainty of energy consumption and travel time of electric buses is neglected. The methodology of robust optimization (RO) is then adopted to address the uncertainty of energy consumption and travel time. The affinely adjustable robust counterpart (AARC) of the deterministic model is developed, and its equivalent tractable mathematical programming is derived. Both the deterministic model and the robust model are demonstrated with a real-world bus system. The results of our study demonstrate that the proposed deterministic model can effectively determine the allocation of DWPT facilities and the battery sizes of electric buses for a DWPT electric bus system; and the robust model can further provide optimal designs that are robust against the uncertainty of energy consumption and travel time for electric buses.« less

Robust planning of dynamic wireless charging infrastructure for battery electric buses

DOE PAGES

Liu, Zhaocai; Song, Ziqi

2017-10-01

Battery electric buses with zero tailpipe emissions have great potential in improving environmental sustainability and livability of urban areas. However, the problems of high cost and limited range associated with on-board batteries have substantially limited the popularity of battery electric buses. The technology of dynamic wireless power transfer (DWPT), which provides bus operators with the ability to charge buses while in motion, may be able to effectively alleviate the drawbacks of electric buses. In this paper, we address the problem of simultaneously selecting the optimal location of the DWPT facilities and designing the optimal battery sizes of electric buses formore » a DWPT electric bus system. The problem is first constructed as a deterministic model in which the uncertainty of energy consumption and travel time of electric buses is neglected. The methodology of robust optimization (RO) is then adopted to address the uncertainty of energy consumption and travel time. The affinely adjustable robust counterpart (AARC) of the deterministic model is developed, and its equivalent tractable mathematical programming is derived. Both the deterministic model and the robust model are demonstrated with a real-world bus system. The results of our study demonstrate that the proposed deterministic model can effectively determine the allocation of DWPT facilities and the battery sizes of electric buses for a DWPT electric bus system; and the robust model can further provide optimal designs that are robust against the uncertainty of energy consumption and travel time for electric buses.« less

Operational Resiliency Management: An Introduction to the Resiliency Engineering Framework

DTIC Science & Technology

2006-09-20

Maturity Model Integration (CMMI) . 5 © 2006 Carnegie Mellon University y FRB Bus Con Conference 2006 Managing Today’s Operational Risk Challenges ...Bus Con Conference 2006 A model is needed to. . . Identify and prioritize risk exposures Define a process improvement roadmap Measure and facilitate...University y FRB Bus Con Conference 2006 Why use a “model” approach? Provides an operational risk roadmap Vendor-neutral, standardized, unbiased

Transit Bus Fuel Economy and Performance Simulation

DOT National Transportation Integrated Search

1984-01-01

This report presents the results of bus simulation studies to determine the effects of various design and operating parameters on bus fuel economy and performance. The bus components are first described in terms of how they are modeled. Then a variat...

Effectiveness of Bus Signal Priority : Final Report

DOT National Transportation Integrated Search

2002-01-01

Effectiveness of Bus Signal Priority (BSP) study evaluates BSP?s impact on traffic operations. The goal was to examine how different situations, such as the level of congestion, placement of bus stops, presence of express bus service, and number of t...

Design Report for Isolated RS-485 Bus Node

DTIC Science & Technology

2016-07-01

controlled wired RS-485 network. The Android-based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in...Android-based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in the system. The Android device

Transit vehicle-to-infrastructure (V2I) applications : near term research and development transit bus stop pedestrian safety application : operational concept.

DOT National Transportation Integrated Search

2014-12-01

This document serves as an Operational Concept for the Transit Bus Stop Pedestrian Safety application. The purpose of this document is to communicate user needs and desired capabilities for and expectations of the Transit Bus Stop Pedestrian Safety a...

Hidden Savings in your Bus Budget

ERIC Educational Resources Information Center

Newby, Ruth

2005-01-01

School transportation industry statistics show the annual average costs for operating and maintaining a single school bus range from $34,000 to $38,000. Operating a school bus fleet at high efficiency has a real impact on the dollars saved for a school district and the reliability of transportation service to students. In this article, the author…

Miami urban partnership agreement (UPA) Pines Boulevard transit signal priority evaluation .report.

DOT National Transportation Integrated Search

2011-09-01

The Miami Urban Partnership Agreement included the conversion of high occupancy vehicle (HOV) lanes on I-95 to high occupancy toll : (HOT) lanes and additional express bus service. It also included funding for the installation of transit signal prior...

Real life testing of a Hybrid PEM Fuel Cell Bus

NASA Astrophysics Data System (ADS)

Folkesson, Anders; Andersson, Christian; Alvfors, Per; Alaküla, Mats; Overgaard, Lars

Fuel cells produce low quantities of local emissions, if any, and are therefore one of the most promising alternatives to internal combustion engines as the main power source in future vehicles. It is likely that urban buses will be among the first commercial applications for fuel cells in vehicles. This is due to the fact that urban buses are highly visible for the public, they contribute significantly to air pollution in urban areas, they have small limitations in weight and volume and fuelling is handled via a centralised infrastructure. Results and experiences from real life measurements of energy flows in a Scania Hybrid PEM Fuel Cell Concept Bus are presented in this paper. The tests consist of measurements during several standard duty cycles. The efficiency of the fuel cell system and of the complete vehicle are presented and discussed. The net efficiency of the fuel cell system was approximately 40% and the fuel consumption of the concept bus is between 42 and 48% lower compared to a standard Scania bus. Energy recovery by regenerative braking saves up 28% energy. Bus subsystems such as the pneumatic system for door opening, suspension and brakes, the hydraulic power steering, the 24 V grid, the water pump and the cooling fans consume approximately 7% of the energy in the fuel input or 17% of the net power output from the fuel cell system. The bus was built by a number of companies in a project partly financed by the European Commission's Joule programme. The comprehensive testing is partly financed by the Swedish programme "Den Gröna Bilen" (The Green Car). A 50 kW el fuel cell system is the power source and a high voltage battery pack works as an energy buffer and power booster. The fuel, compressed hydrogen, is stored in two high-pressure stainless steel vessels mounted on the roof of the bus. The bus has a series hybrid electric driveline with wheel hub motors with a maximum power of 100 kW. Hybrid Fuel Cell Buses have a big potential, but there are still many issues to consider prior to full-scale commercialisation of the technology. These are related to durability, lifetime, costs, vehicle and system optimisation and subsystem design. A very important factor is to implement an automotive design policy in the design and construction of all components, both in the propulsion system as well as in the subsystems.

National Fuel Cell Bus Program: Accelerated Testing Evaluation Report and Appendices, Alameda-Contra Costa Transit District (AC Transit)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Eudy, L.

2009-01-01

This is an evaluation of hydrogen fuel cell transit buses operating at AC Transit in revenue service since March 20, 2006 compared to similar diesel buses operating from the same depot. This evaluation report includes results from November 2007 through October 2008. Evaluation results include implementation experience, fueling station operation, fuel cell bus operations at Golden Gate Transit, and evaluation results at AC Transit (bus usage, availability, fuel economy, maintenance costs, and roadcalls).

Savannah River bus project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Summers, W.A.

1998-08-01

The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogenmore » fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.« less

Bus operator perceptions of safety risks.

DOT National Transportation Integrated Search

2013-07-01

This paper presents the results of a survey of TriMet bus operators addressing safety risks in their assigned work. Surveyed risk factors : were organized into five categories: vehicle design and condition; route layout; operating conditions; fatigue...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Eudy, L.

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

Large school bus design vehicle dimensions

DOT National Transportation Integrated Search

1998-09-01

A survey of United States school bus operators and manufacturers was conducted to define the larger sizes of school buses in regular use. A mid-60 passenger type-c bus (SB-C) and a mid-80 passenger type-D bus (SB-D) were selected as design vehicles. ...

Ultrafine particle emissions by in-use diesel buses of various generations at low-load regimes

NASA Astrophysics Data System (ADS)

Tartakovsky, L.; Baibikov, V.; Comte, P.; Czerwinski, J.; Mayer, A.; Veinblat, M.; Zimmerli, Y.

2015-04-01

Ultrafine particles (UFP) are major contributors to air pollution due to their easy gas-like penetration into the human organism, causing adverse health effects. This study analyzes UFP emissions by buses of different technologies (from Euro II till Euro V EEV - Enhanced Environmentally-friendly Vehicle) at low-load regimes. Additionally, the emission-reduction potential of retrofitting with a diesel particle filter (DPF) is demonstrated. A comparison of the measured, engine-out, particle number concentrations (PNC) for buses of different technological generations shows that no substantial reduction of engine-out emissions at low-load operating modes is observed for newer bus generations. Retrofitting the in-use urban and interurban buses of Euro II till Euro IV technologies by the VERT-certified DPF confirmed its high efficiency in reduction of UFP emissions. Particle-count filtration efficiency values of the retrofit DPF were found to be extremely high - greater than 99.8%, similar to that of the OEM filter in the Euro V bus.

Bus Stops and Pedestrian-Motor Vehicle Collisions in Lima, Peru: A Matched Case-Control Study

PubMed Central

Quistberg, D. Alex; Koepsell, Thomas D.; Johnston, Brian D.; Boyle, Linda Ng; Miranda, J. Jaime; Ebel, Beth E.

2015-01-01

Objective To evaluate the relationship between bus stop characteristics and pedestrian-motor vehicle collisions. Design Matched case-control study where the units of study were pedestrian crossing. Setting Random sample of 11 police commissaries in Lima, Peru. Data collection occurred from February, 2011 to September, 2011. Participants 97 intersection cases representing 1,134 collisions and 40 mid-block cases representing 469 collisions that occurred between October, 2010 and January, 2011 and their matched controls. Main Exposures Presence of a bus stop and specific bus stop characteristics. Main Outcome Occurrence of a pedestrian-motor vehicle collision. Results Intersections with bus stops were three times more likely to have a pedestrian-vehicle collision (OR 3.28, 95% CI 1.53-7.03), relative to intersections without bus stops. Both formal and informal bus stops were associated with a higher odds of a collision at intersections (OR 6.23, 95% CI 1.76-22.0 and OR 2.98, 1.37-6.49). At mid-block sites, bus stops on a bus-dedicated transit lane were also associated with collision risk (OR 2.36, 95% CI 1.02-5.42). All bus stops were located prior to the intersection, contrary to practices in most high income countries. Conclusions In urban Lima, the presence of a bus stop was associated with a three-fold increase in risk of a pedestrian collision. The highly competitive environment among bus companies may provide an economic incentive for risky practices such as dropping off passengers in the middle of traffic and jockeying for position with other buses. Bus stop placement should be considered to improve pedestrian safety. PMID:24357516

Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system [research brief].

DOT National Transportation Integrated Search

2012-03-01

Government regulators and transportation operators of public bus systems are concerned about terrorist attacks. Bus attacks in Israel between late September 2000 and the end of 2006, a period known as the Second Intifada, are particularly well known....

Transit bus stop pedestrian warning application : concept of operations document.

DOT National Transportation Integrated Search

2015-02-04

This document describes the Concept of Operations (ConOps) for the Transit Bus Stop Pedestrian Warning (TSPW) application. The ConOps describes the current state of operations with respect to the integration of connected vehicle technology in transit...

Appraisal on Rail Transit Development: A Review on Train Services and Safety

NASA Astrophysics Data System (ADS)

Nordin, Noor Hafiza binti; Masirin, Mohd Idrus Haji Mohd; Ghazali, Mohd Imran bin; Azis, Mohd Isom bin

2017-08-01

The ever increasing problems faced by population around the world have made demands that transportation need to be improved as an effective and efficient communication means. It is considered as a necessity especially when rapid development and economic growth of a country is the agenda. Among the transportation modes being focused as critical facilities are the bus system, rail system, road network, shipping system and air transportation system. Rail transport is a means of conveyance of passengers and goods by way of wheeled vehicles running on rail tracks. In Malaysia, the railway network has evolved tremendously since its inception in the early 19th century. It has grown proportionally with the national development. Railway network does not only mean for rural transportation, but it also considered as a solution to urban congestion challenges. Currently, urban rail transit is the most popular means of urban transportation system especially as big cities such as Kuala Lumpur. This paper presents the definition of rail transportation system and its role in urban or sub-urban operation. It also describes the brief history of world railway transportation including a discussion on Malaysian rail history perspective. As policy and standard are important in operating a railway system, this paper also illustrates and discusses some elements which have an impact on the effectiveness and efficiency of train operation. Towards the end, this paper also shares the importance of railway safety based on real case studies around the world. Thus, it is hoped that this paper will enable the public to understand the rail transit development and appreciate its existence as a public transportation system.

Modeling and Simulation of Bus Dispatching Policy for Timed Transfers on Signalized Networks

NASA Astrophysics Data System (ADS)

Cho, Hsun-Jung; Lin, Guey-Shii

2007-12-01

The major work of this study is to formulate the system cost functions and to integrate the bus dispatching policy with signal control. The integrated model mainly includes the flow dispersion model for links, signal control model for nodes, and dispatching control model for transfer terminals. All such models are inter-related for transfer operations in one-center transit network. The integrated model that combines dispatching policies with flexible signal control modes can be applied to assess the effectiveness of transfer operations. It is found that, if bus arrival information is reliable, an early dispatching decision made at the mean bus arrival times is preferable. The costs for coordinated operations with slack times are relatively low at the optimal common headway when applying adaptive route control. Based on such findings, a threshold function of bus headway for justifying an adaptive signal route control under various time values of auto drivers is developed.

The potentials and problems of private sector transportation services : activities in the New York region

DOT National Transportation Integrated Search

1987-01-01

This project explored the problems and potentials of new forms of private urban transportation that have evolved in the Metropolitan New York region in the last 20 years, as well as the problems and potentials of private urban bus service that has ex...

Method and systems for a radiation tolerant bus interface circuit

NASA Technical Reports Server (NTRS)

Kinstler, Gary A. (Inventor)

2007-01-01

A bus management tool that allows communication to be maintained between a group of nodes operatively connected on two busses in the presence of radiation by transmitting periodically a first message from one to another of the nodes on one of the busses, determining whether the first message was received by the other of the nodes on the first bus, and when it is determined that the first message was not received by the other of the nodes, transmitting a recovery command to the other of the nodes on a second of the of busses. Methods, systems, and articles of manufacture consistent with the present invention also provide for a bus recovery tool on the other node that re-initializes a bus interface circuit operatively connecting the other node to the first bus in response to the recovery command.

Short-term exposure to PM 10, PM 2.5, ultrafine particles and CO 2 for passengers at an intercity bus terminal

NASA Astrophysics Data System (ADS)

Cheng, Yu-Hsiang; Chang, Hsiao-Peng; Hsieh, Cheng-Ju

2011-04-01

The Taipei Bus Station is the main transportation hub for over 50 bus routes to eastern, central, and southern Taiwan. Daily traffic volume at this station is about 2500 vehicles, serving over 45,000 passengers daily. The station is a massive 24-story building housing a bus terminal, a business hotel, a shopping mall, several cinemas, offices, private residential suites, and over 900 parking spaces. However, air quality inside this bus terminal is a concern as over 2500 buses are scheduled to run daily. This study investigates the PM 10, PM 2.5, UFP and CO 2 levels inside and outside the bus terminal. All measurements were taken between February and April 2010. Measurement results show that coarse PM inside the bus terminal was resuspended by the movement of large numbers of passengers. The fine and ultrafine PM in the station concourse were from outside vehicles. Moreover, fine and ultrafine PM at waiting areas were exhausted directly from buses in the building. The CO 2 levels at waiting areas were likely elevated by bus exhaust and passengers exhaling. The PM 10, PM 2.5 and CO 2 levels at the bus terminal were lower than Taiwan's EPA suggested standards for indoor air quality. However, UFP levels at the bus terminal were significantly higher than those in the urban background by about 10 times. Therefore, the effects of UFPs on the health of passengers and workers must be addressed at this bus terminal since the levels of UFPs are higher than >1.0 × 10 5 particles cm -3.

College Students or Criminals? A Postcolonial Geographic Analysis of the Social Field of Whiteness at an Urban Community College Branch Campus and Suburban Main Campus

ERIC Educational Resources Information Center

Dache-Gerbino, Amalia; White, Julie A.

2016-01-01

Objective: This study illustrates how external factors of urban and suburban racializations contribute to criminalization and surveillance of an urban community college campus and bus shelters surrounding it. Method: A postcolonial geographic research design is used to analyze geographic and qualitative data. Results: Results show that an urban…

Relative importance of school bus-related microenvironments to children's pollutant exposure.

PubMed

Behrentz, Eduardo; Sabin, Lisa D; Winer, Arthur M; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

2005-10-01

Real-time concentrations of black carbon, particle-bound polycyclic aromatic hydrocarbons, nitrogen dioxide, and fine particulate counts, as well as integrated and real-time fine particulate matter (PM2.5) mass concentrations were measured inside school buses during long commutes on Los Angeles Unified School District bus routes, at bus stops along the routes, at the bus loading/unloading zone in front of the selected school, and at nearby urban "background" sites. Across all of the pollutants, mean concentrations during bus commutes were higher than in any other microenvironment. Mean exposures (mean concentration times time spent in a particular microenvironment) in bus commutes were between 50 and 200 times greater than those for the loading/unloading microenvironment, and 20-40 times higher than those for the bus stops, depending on the pollutant. Although the analyzed school bus commutes represented only 10% of a child's day, on average they contributed one-third of a child's 24-hr overall black carbon exposure during a school day. For species closely related to vehicle exhaust, the within- cabin exposures were generally dominated by the effect of surrounding traffic when windows were open and by the bus's own exhaust when windows were closed. Low-emitting buses generally exhibited high concentrations only when traveling behind a diesel vehicle, whereas high-emitting buses exhibited high concentrations both when following other diesel vehicles and when idling without another diesel vehicle in front of the bus. To reduce school bus commute exposures, we recommend minimizing commute times, avoiding caravanning with other school buses, using the cleanest buses for the longest bus routes, maintaining conventional diesel buses to eliminate visible emissions, and transitioning to cleaner fuels and advanced particulate control technologies as soon as possible.

Advanced control design for hybrid turboelectric vehicle

NASA Technical Reports Server (NTRS)

Abban, Joseph; Norvell, Johnesta; Momoh, James A.

1995-01-01

The new environment standards are a challenge and opportunity for industry and government who manufacture and operate urban mass transient vehicles. A research investigation to provide control scheme for efficient power management of the vehicle is in progress. Different design requirements using functional analysis and trade studies of alternate power sources and controls have been performed. The design issues include portability, weight and emission/fuel efficiency of induction motor, permanent magnet and battery. A strategic design scheme to manage power requirements using advanced control systems is presented. It exploits fuzzy logic, technology and rule based decision support scheme. The benefits of our study will enhance the economic and technical feasibility of technological needs to provide low emission/fuel efficient urban mass transit bus. The design team includes undergraduate researchers in our department. Sample results using NASA HTEV simulation tool are presented.

Increasing security in inter-chip communication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, Nathan J.; Hamlet, Jason; Bauer, Todd

An apparatus for increasing security in inter-chip communication includes a sending control module, a communication bus, and a receiving control module. The communication bus is coupled between the sending control module and the receiving control module. The sending control module operates to send data on the communication bus, disable the communication bus when threats are detected, or both.

Increasing security in inter-chip communication

DOEpatents

Edwards, Nathan J; Hamlet, Jason; Bauer, Todd; Helinski, Ryan

2014-10-28

An apparatus for increasing security in inter-chip communication includes a sending control module, a communication bus, and a receiving control module. The communication bus is coupled between the sending control module and the receiving control module. The sending control module operates to send data on the communication bus, disable the communication bus when threats are detected, or both.

Assessing exposure to diesel exhaust particles: a case study.

PubMed

See, Siao Wei; Balasubramanian, Rajasekhar; Yang, Tzuo Sern; Karthikeyan, Sathrugnan

2006-11-01

The assessment of the vehicular contributions to urban pollution levels is of particular importance given the current interest in the possible adverse health effects. This study focused on human exposure to diesel-engine-derived particulate matter. Diesel vehicles are known to emit fine particulate matter (PM2.5) containing carcinogens such as polycyclic aromatic hydrocarbons (PAHs), and have therefore received considerable attention. In this study, the physical (mass and number concentration, and size distribution) and chemical (PAHs) properties were investigated at a major bus interchange in Singapore, influenced only by diesel exhausts. Number concentration and size distribution of particles were determined in real time, while the mass concentrations of PM2.5, and PAHs were measured during operating and nonoperating hours. The average mass concentrations of PM2.5 and PAHs increased by a factor of 2.34 and 5.18, respectively, during operating hours. The average number concentration was also elevated by a factor of 5.07 during operating hours. This increase in the concentration of PM2.5 particles and their chemical constituents during operating hours was attributable to diesel emissions from in-use buses based on the particle size analysis, correlation among PAHs, and the commonly used PAHs diagnostic ratios. To evaluate the potential health threat due inhalation of air pollutants released from diesel engines, the incremental lifetime cancer risk was also calculated for a maximally exposed individual. The findings indicate that the air quality at the bus interchange poses adverse health effects.

78 FR 44112 - California State Motor Vehicle Pollution Control Standards; Urban Buses; Request for Waiver of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-23

... Board (CARB) its request for a waiver of preemption for emission standards and related test procedures... standards and test procedures for heavy-duty urban bus engines and vehicles. The 2000 rulemaking included... to emission standards and test procedures resulting from these five sets of amendments were codified...

San Antonio's 1983 Bus Passenger Survey

DOT National Transportation Integrated Search

1983-10-01

Many transit operators routinely collect ridership data in order to provide a : basis for the planning of bus services. Often a survey is conducted of bus : riders to determine their riding habits, their views about the quality of : current service, ...

Mass transit : bus rapid transit shows promise

DOT National Transportation Integrated Search

2001-09-17

The U. S. General Accounting Office (GAO) was asked to (1) examine the federal role in supporting Bus Rapid Transit; (2) compare the capital costs, operating costs, and performance characteristics of Bus Rapid Transit and Light Rail systems; and (3) ...

Bus transportation in Connecticut : data for planning, agenda for action

DOT National Transportation Integrated Search

1974-03-01

Presents the conclusions and recommendations of the Connecticut Public Expenditure Council regarding the present status of bus transit service throughout Connecticut; operational and funding issues; status of bus transit elsewhere in the U. S. and se...

Drive Cycle Analysis, Measurement of Emissions and Fuel Consumption of a PHEV School Bus: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnitt, R.; Gonder, J.

The National Renewable Energy Laboratory (NREL) collected and analyzed real-world school bus drive cycle data and selected similar standard drive cycles for testing on a chassis dynamometer. NREL tested a first-generation plug-in hybrid electric vehicle (PHEV) school bus equipped with a 6.4L engine and an Enova PHEV drive system comprising a 25-kW/80 kW (continuous/peak) motor and a 370-volt lithium ion battery pack. A Bluebird 7.2L conventional school bus was also tested. Both vehicles were tested over three different drive cycles to capture a range of driving activity. PHEV fuel savings in charge-depleting (CD) mode ranged from slightly more than 30%more » to a little over 50%. However, the larger fuel savings lasted over a shorter driving distance, as the fully charged PHEV school bus would initially operate in CD mode for some distance, then in a transitional mode, and finally in a charge-sustaining (CS) mode for continued driving. The test results indicate that a PHEV school bus can achieve significant fuel savings during CD operation relative to a conventional bus. In CS mode, the tested bus showed small fuel savings and somewhat higher nitrogen oxide (NOx) emissions than the baseline comparison bus.« less

Interprocessor bus switching system for simultaneous communication in plural bus parallel processing system

DOEpatents

Atac, R.; Fischler, M.S.; Husby, D.E.

1991-01-15

A bus switching apparatus and method for multiple processor computer systems comprises a plurality of bus switches interconnected by branch buses. Each processor or other module of the system is connected to a spigot of a bus switch. Each bus switch also serves as part of a backplane of a modular crate hardware package. A processor initiates communication with another processor by identifying that other processor. The bus switch to which the initiating processor is connected identifies and secures, if possible, a path to that other processor, either directly or via one or more other bus switches which operate similarly. If a particular desired path through a given bus switch is not available to be used, an alternate path is considered, identified and secured. 11 figures.

Interprocessor bus switching system for simultaneous communication in plural bus parallel processing system

DOEpatents

Atac, Robert; Fischler, Mark S.; Husby, Donald E.

1991-01-01

A bus switching apparatus and method for multiple processor computer systems comprises a plurality of bus switches interconnected by branch buses. Each processor or other module of the system is connected to a spigot of a bus switch. Each bus switch also serves as part of a backplane of a modular crate hardware package. A processor initiates communication with another processor by identifying that other processor. The bus switch to which the initiating processor is connected identifies and secures, if possible, a path to that other processor, either directly or via one or more other bus switches which operate similarly. If a particular desired path through a given bus switch is not available to be used, an alternate path is considered, identified and secured.

District of Columbia tour bus management initiative final report.

DOT National Transportation Integrated Search

2003-10-01

The objective of the District of Columbia Tour Bus Management Initiative is to develop a plan that will ameliorate the long-standing problems, as identified above, that negatively affect tour bus operations as well as traffic conditions, the visitor ...

Analysis of real-time variables affecting children's exposure to diesel-related pollutants during school bus commutes in Los Angeles

NASA Astrophysics Data System (ADS)

Sabin, Lisa D.; Kozawa, Kathleen; Behrentz, Eduardo; Winer, Arthur M.; Fitz, Dennis R.; Pankratz, David V.; Colome, Steven D.; Fruin, Scott A.

Variables affecting children's exposure during school bus commutes were investigated using real-time measurements of black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PB-PAH) and nitrogen dioxide (NO 2) inside 3 conventional diesel school buses, a particle trap-outfitted (TO) diesel school bus and a compressed natural gas (CNG) school bus, while traveling along an urban Los Angeles Unified School District bus route. A video camera was mounted at the front of each bus to record roadway conditions ahead of the bus during each commute. The videotapes from 12 commutes, in conjunction with pollutant concentration time series, were used to determine the influence of variables such as vehicles being followed, bus type and roadway type on pollutant concentrations inside the bus. For all buses tested, the highest concentrations of BC, PB-PAH and NO 2 were observed when following a diesel school bus, especially if that bus was emitting visible exhaust. This result was important because other diesel school buses were responsible for the majority of the diesel vehicle encounters, primarily due to caravanning with each other when leaving a school at the same time. Compared with following a gasoline vehicle or no target, following a smoky diesel school bus yielded BC and PB-PAH concentrations inside the cabin 8 and 11 times higher, respectively, with windows open, and ˜1.8 times higher for both pollutants with windows closed. When other diesel vehicles were not present, pollutant concentrations were highest inside the conventional diesel buses and lowest inside the CNG bus, while the TO diesel bus exhibited intermediate concentrations. Differences in pollutant concentrations between buses were most pronounced with the bus windows closed, and were attributed to a combination of higher concentrations in the exhaust and higher exhaust gas intrusion rates for the conventional diesel buses. Conventional diesel school buses can have a double exposure impact on commuting children: first, exposures to the exhaust from other nearby diesel school buses and, second, exposure to the bus's own exhaust through "self-pollution".

Economic Benefit of Introducing a Bus Rapid Transit (BRT) in Kano State Nigeria

NASA Astrophysics Data System (ADS)

Ahmad, K. A.; Afolabi, S.; Nda, M.; Daura, H. A.

2018-04-01

The objective of this study is to know the variables use in quantifying economic benefits of public transport project, contribution of public transport to economic productivity This paper attempts to provide a Road User Cost (RUC) comparison of current usage of Buses and Cars in three different stages which are the present time, do nothing and the introduction of new modes. Vehicle operating cost (VOC), value of time (VOT), pollution cost, accident cost and environmental cost are calculated in other to know the benefits for their abilities to ensure accessibility and mobility, reduce accidents and reduce environmental loss. The study stretch involves an 11.1 km of 2-lane divided carriageway road connecting Kabuga bus stop to Janguza market. Social costs which included accident costs, accident cost of cars (private modes) were found to be 50 times the accident cost of bus accidents. California Air Resource Board (CARB) model was adopted to evaluate Environmental costs. The total road user costs were then obtained to provide comparative evaluation among the study modes. Furthermore, the multiple future scenarios were created to provide understanding about the need for inclusion of other modes. In this regard, this paper provided a framework for the cost evaluation for an urban area and results indicate that buses are more cost-effective in transportation of equivalent number of passengers.

Land developer participation in providing for bus transit facilities and operations

DOT National Transportation Integrated Search

2002-03-01

This report provides an overview of the various non-regulatory and regulatory approaches for engaging private sector land developer participation in contributing toward the provision of public bus transit capital facilities and the cost of operations...

Impact of congestion on bus operations and costs.

DOT National Transportation Integrated Search

2003-10-01

Traffic congestion in Northern New Jersey imposes substantial operational and monetary penalty on bus service. The purpose of this project was to quantify the additional time and costs due to traffic congestion. A regression model was developed that ...

Bus operator safety : critical issues examination and model practices.

DOT National Transportation Integrated Search

2014-01-01

In this study, researchers at the National Center for Transit Research performed a multi-topic comprehensive : examination of bus operator-related critical safety and personal security issues. The goals of this research : effort were to: : 1. Identif...

Front Range commuter bus study. Phase 2 : final report

DOT National Transportation Integrated Search

2003-10-01

The goal of Front Range Commuter Bus service would be to provide a commuter bus service that would operate seamlessly with local transit systems and would be run through a partnership with each of the cities, CDOT, RTD and participating private provi...

American Fuel Cell Bus Project Evaluation : Third Report

DOT National Transportation Integrated Search

2017-05-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses (FCEB) operating in the Coachella Valley area of California. The AFCB, built on an ElDorado National-California 40-foot Axess bus p...

Evolution and Operations of the Reston Virginia Commuter Bus Service

DOT National Transportation Integrated Search

1977-08-01

The report focuses on documenting and assessing the evolution and operations of the Reston Commuter Bus (RCB). RCB is a good example of a community group overcoming many legal, regulatory, and institutional constraints to develop and refine a viable ...

A qualitative analysis of bus simulator training on transit incidents : a case study in Florida.

DOT National Transportation Integrated Search

2013-06-01

The purpose of this research was to track and observe three Florida public transit agencies as they incorporated and integrated computer-based transit bus simulators into their existing bus operator training programs. In addition to the three Florida...

40 CFR 85.1401 - General applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1401 General... population of 750,000 or more that have their engines rebuilt or replaced after January 1, 1995. ...

40 CFR 85.1401 - General applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1401 General... population of 750,000 or more that have their engines rebuilt or replaced after January 1, 1995. ...

40 CFR 85.1401 - General applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1401 General... population of 750,000 or more that have their engines rebuilt or replaced after January 1, 1995. ...

40 CFR 85.1401 - General applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1401 General... population of 750,000 or more that have their engines rebuilt or replaced after January 1, 1995. ...

Modular sensor network node

DOEpatents

Davis, Jesse Harper Zehring [Berkeley, CA; Stark, Jr., Douglas Paul; Kershaw, Christopher Patrick [Hayward, CA; Kyker, Ronald Dean [Livermore, CA

2008-06-10

A distributed wireless sensor network node is disclosed. The wireless sensor network node includes a plurality of sensor modules coupled to a system bus and configured to sense a parameter. The parameter may be an object, an event or any other parameter. The node collects data representative of the parameter. The node also includes a communication module coupled to the system bus and configured to allow the node to communicate with other nodes. The node also includes a processing module coupled to the system bus and adapted to receive the data from the sensor module and operable to analyze the data. The node also includes a power module connected to the system bus and operable to generate a regulated voltage.

A study of multiplex data bus techniques for the space shuttle

NASA Technical Reports Server (NTRS)

Kearney, R. J.; Kalange, M. A.

1972-01-01

A comprehensive technology base for the design of a multiplexed data bus subsystem is provided. Extensive analyses, both analytical and empirical, were performed. Subjects covered are classified under the following headings: requirements identification and analysis; transmission media studies; signal design and detection studies; synchronization, timing, and control studies; user-subsystem interface studies; operational reliability analyses; design of candidate data bus configurations; and evaluation of candidate data bus designs.

A summary of design, policies and operational characteristics for shared bicycle/bus lanes.

DOT National Transportation Integrated Search

2012-07-01

This report contains the results of an investigation of the design and operation of shared bicycle/bus lanes in municipalities in the United States and other countries. These lanes are designated for use by public transit buses, bicycles, and usually...

Analysis of bus collision and non-collision incidents using transit ITS and other archived operations data.

DOT National Transportation Integrated Search

2010-11-01

This report analyzes factors contributing to bus operations safety incidents at TriMet, the transit provider for the Portland Oregon metropolitan : region. The analysis focuses on 4,631 collision and non-collision incidents that occurred between 2006...

Evaluation of transit operations : data applications of Tri-Met's automated bus dispatching system

DOT National Transportation Integrated Search

2001-02-01

This paper presents an analysis of operating performance for Tri-Met, the transit provider for the Portland, Oregon metropolitan area. The analysis draws on data recovered by Tri-Met's automated Bus Dispatching System (BDS) and focuses on two main su...

Small City Transit : Bremerton, Washington : Privately Operated Subscription Bus Service to an Industrial Site

DOT National Transportation Integrated Search

1976-03-01

Bremerton, Washington, is an illustration of a privately operated, profitmaking subscription bus service. This case study is one of thirteen examples of a transit service in a small community. The background of the community is discussed along with a...

Fine urban and precursor emissions control for diesel urban transit buses.

PubMed

Lanni, Thomas

2003-01-01

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled "Clean Diesel Air Quality Demonstration Program" has been initiated by the New York City Metropolitan Transit Authority (MTA) under the supervision of New York State Department of Environmental Conservation and with active participation from Johnson Matthey, Corning, Equilon, Environment Canada and RAD Energy. Under this program, several MTA transit buses with DDC Series 50 engines were equipped with Continuously Regenerating Technology (CRTTM) particulate filter systems and have been operated with ultra low sulfur diesel (<30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9-month period for durability and maintainability of the particulate filter. In addition, an extensive emissions testing program was carried out using transient cycles on a chassis dynamometer to evaluate the emissions reductions obtained with the particle filter. In this paper, the emissions testing data from the Clean Diesel Air Quality Demonstration Program are discussed in detail.

Oregon Pupil Transportation Manual. Revised Regulations and Responsibilities.

ERIC Educational Resources Information Center

Oregon State Dept. of Education, Salem.

Designed for use by Oregon school bus drivers and administrators, this manual answers common questions about school bus transportation in Oregon, including those about the laws governing pupil transportation, the regulations governing pupil transportation administration, and the laws on school bus operation. A chapter of advisory materials covers…

Highway Accident Summary Report: Bus Collision With Pedestrians, Normandy, Missouri, June 11, 1997

DOT National Transportation Integrated Search

1998-02-19

On June 11, 1997, a transit bus collided with seven pedestrians at a "park and ride" transit facility in Normandy, Missouri. The bus was being operated by a driver trainee who had just completed a routine stop at the station. After allowing the passe...

Operationally Responsive Space Standard Bus Battery Thermal Balance Testing and Heat Dissipation Analysis

NASA Technical Reports Server (NTRS)

Marley, Mike

2008-01-01

The focus of this paper will be on the thermal balance testing for the Operationally Responsive Space Standard Bus Battery. The Standard Bus thermal design required that the battery be isolated from the bus itself. This required the battery to have its own thermal control, including heaters and a radiator surface. Since the battery was not ready for testing during the overall bus thermal balance testing, a separate test was conducted to verify the thermal design for the battery. This paper will discuss in detail, the test set up, test procedure, and results from this test. Additionally this paper will consider the methods taken to determine the heat dissipation of the battery during charge and discharge. It seems that the heat dissipation for Lithium Ion batteries is relatively unknown and hard to quantify. The methods used during test and the post test analysis to estimate the heat dissipation of the battery will be discussed.

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes

PubMed Central

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes. PMID:26294903

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes.

PubMed

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes.

Extracting potential bus lines of Customized City Bus Service based on public transport big data

NASA Astrophysics Data System (ADS)

Ren, Yibin; Chen, Ge; Han, Yong; Zheng, Huangcheng

2016-11-01

Customized City Bus Service (CCBS) can reduce the traffic congestion and environmental pollution that caused by the increasing in private cars, effectively. This study aims to extract the potential bus lines and each line's passenger density of CCBS by mining the public transport big data. The datasets used in this study are mainly Smart Card Data (SCD) and bus GPS data of Qingdao, China, from October 11th and November 7th 2015. Firstly, we compute the temporal-origin-destination (TOD) of passengers by mining SCD and bus GPS data. Compared with the traditional OD, TOD not only has the spatial location, but also contains the trip's boarding time. Secondly, based on the traditional DBSCAN algorithm, we put forwards an algorithm, named TOD-DBSCAN, combined with the spatial-temporal features of TOD.TOD-DBSCAN is used to cluster the TOD trajectories in peak hours of all working days. Then, we define two variables P and N to describe the possibility and passenger destiny of a potential CCBS line. P is the probability of the CCBS line. And N represents the potential passenger destiny of the line. Lastly, we visualize the potential CCBS lines extracted by our procedure on the map and analyse relationship between potential CCBS lines and the urban spatial structure.

Characterization of transit ride quality.

DOT National Transportation Integrated Search

2016-08-01

Strategies often proposed to combat the growing traffic congestion problems of urban environments target enhancements to increase the use of bus transit. Therefore, service providers are keen to identify and understand factors that could attract more...

Apparatus, system and method for providing cryptographic key information with physically unclonable function circuitry

DOEpatents

Areno, Matthew

2015-12-08

Techniques and mechanisms for providing a value from physically unclonable function (PUF) circuitry for a cryptographic operation of a security module. In an embodiment, a cryptographic engine receives a value from PUF circuitry and based on the value, outputs a result of a cryptographic operation to a bus of the security module. The bus couples the cryptographic engine to control logic or interface logic of the security module. In another embodiment, the value is provided to the cryptographic engine from the PUF circuitry via a signal line which is distinct from the bus, where any exchange of the value by either of the cryptographic engine and the PUF circuitry is for communication of the first value independent of the bus.

Characterizing the range of children's air pollutant exposure during school bus commutes.

PubMed

Sabin, Lisa D; Behrentz, Eduardo; Winer, Arthur M; Jeong, Seong; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

2005-09-01

Real-time and integrated measurements of gaseous and particulate pollutants were conducted inside five conventional diesel school buses, a diesel bus with a particulate trap, and a bus powered by compressed natural gas (CNG) to determine the range of children's exposures during school bus commutes and conditions leading to high exposures. Measurements were made during 24 morning and afternoon commutes on two Los Angeles Unified School District bus routes from South to West Los Angeles, with seven additional runs on a rural/suburban route, and three runs to test the effect of window position. For these commutes, the mean concentrations of diesel vehicle-related pollutants ranged from 0.9 to 19 microg/m(3) for black carbon, 23 to 400 ng/m(3) for particle-bound polycyclic aromatic hydrocarbon (PB-PAH), and 64 to 220 microg/m(3) for NO(2). Concentrations of benzene and formaldehyde ranged from 0.1 to 11 microg/m(3) and 0.3 to 5 microg/m(3), respectively. The highest real-time concentrations of black carbon, PB-PAH and NO(2) inside the buses were 52 microg/m(3), 2000 ng/m(3), and 370 microg/m(3), respectively. These pollutants were significantly higher inside conventional diesel buses compared to the CNG bus, although formaldehyde concentrations were higher inside the CNG bus. Mean black carbon, PB-PAH, benzene and formaldehyde concentrations were higher when the windows were closed, compared with partially open, in part, due to intrusion of the bus's own exhaust into the bus cabin, as demonstrated through the use of a tracer gas added to each bus's exhaust. These same pollutants tended to be higher on urban routes compared to the rural/suburban route, and substantially higher inside the bus cabins compared to ambient measurements. Mean concentrations of pollutants with substantial secondary formation, such as PM(2.5), showed smaller differences between open and closed window conditions and between bus routes. Type of bus, traffic congestion levels, and encounters with other diesel vehicles contributed to high exposure variability between runs.

76 FR 10634 - Agency Information Collection Activity Under OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-25

... assistance from FTA to enter into a charter bus agreement with the Secretary of Transportation (delegated to... intercity charter bus operators from unfair competition by FTA recipients. 49 U.S.C. 5302(a)(10) as..., to provide charter bus service with FTA-funded facilities and equipment only if it is incidental to...

State intercity bus plan : a report to the California Legislature in conformity with Chapter 99, item 266-001-041 of the 1981 Budget Act

DOT National Transportation Integrated Search

1982-03-01

The legislative directive for the State Intercity Bus Plan asked that the Department offer alternatives for future State involvement in the intercity bus area, estimates for the projected State capital and operating costs and revenues for each of the...

Real-world operation conditions and on-road emissions of Beijing diesel buses measured by using portable emission measurement system and electric low-pressure impactor.

PubMed

Liu, Zhihua; Ge, Yunshan; Johnson, Kent C; Shah, Asad Naeem; Tan, Jianwei; Wang, Chu; Yu, Linxiao

2011-03-15

On-road measurement is an effective method to investigate real-world emissions generated from vehicles and estimate the difference between engine certification cycles and real-world operating conditions. This study presents the results of on-road measurements collected from urban buses which propelled by diesel engine in Beijing city. Two widely used Euro III emission level buses and two Euro IV emission level buses were chosen to perform on-road emission measurements using portable emission measurement system (PEMS) for gaseous pollutant and Electric Low Pressure Impactor (ELPI) for particulate matter (PM) number emissions. The results indicate that considerable discrepancies of engine operating conditions between real-world driving cycles and engine certification cycles have been observed. Under real-world operating conditions, carbon monoxide (CO) and hydrocarbon (HC) emissions can easily meet their respective regulations limits, while brake specification nitrogen oxide (bsNO(x)) emissions present a significant deviation from its corresponding limit. Compared with standard limits, the real-world bsNO(x) emission of the two Euro III emission level buses approximately increased by 60% and 120% respectively, and bsNO(x) of two Euro IV buses nearly twice standard limits because Selective Catalytic Reduction (SCR) system not active under low exhaust temperature. Particle mass were estimated via particle size distribution with the assumption that particle density and diameter is liner. The results demonstrate that nanometer size particulate matter make significant contribution to total particle number but play a minor role to total particle mass. It is suggested that specific certified cycle should be developed to regulate bus engines emissions on the test bench or use PEMS to control the bus emissions under real-world operating conditions. Copyright © 2010 Elsevier B.V. All rights reserved.

ALR-46 Computer Graphics System for the Robins Air Force Base Electronic Warfare Division Engineering Branch Laboratory.

DTIC Science & Technology

1981-12-01

CGS Funtional Requirements and System Configuration Introduction The first phase of any system development is to define requirements. The development of...between any two devices and the bus is in a master/slave relationship . During any bus operation, the bus master controls the bus when communicating with...illustrate the CASE statement of the PASCAL language. These extensions are mentioned to illustrate the relationships that the Warnier-Orr diagrams exhibit

Heavy Duty Diesel Truck and Bus Hybrid Powertrain Study

DTIC Science & Technology

2012-03-01

electric 22 ft. bus that offers greater range than battery-electric buses can provide. Designed to seat 22 passengers plus standees, this Ebus model...system that has both parallel and series operating modes. The relatively low volume of many truck and bus designs has inhibited the development of...that battery packs need to be designed for 50,000 lifetime energy storage cycles in a hybrid transit bus vs. just 3,600 cycles in the typical

Environmental Technology Verification Test Report of Mobile Source Selective Catalytic Reduction, Johnson Matthey SCCRT, Version 1, Selective Catalytic Reduction Technology with a Catalyzed Continuously Regenerating Trap

EPA Science Inventory

The Johnson Matthey SCCRT, v.1 technology is a urea-based SCR system combined with a CCRT filter designed for on-highway light, medium, and heavy heavy-duty diesel, urban and non-urban, bus exhaust gas recirculation (EGR)-or non-EGR-equipped engines for use with commercial ultra-...

49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

Code of Federal Regulations, 2010 CFR

2010-10-01

.... Because the operator will not become familiar with the detailed design of all new bus models that are tested, tests to determine the time and skill required to remove and reinstall an engine, a transmission... feasible to conduct statistical reliability tests. The detected bus failures, repair time, and the actions...

49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

Code of Federal Regulations, 2011 CFR

2011-10-01

.... Because the operator will not become familiar with the detailed design of all new bus models that are tested, tests to determine the time and skill required to remove and reinstall an engine, a transmission... feasible to conduct statistical reliability tests. The detected bus failures, repair time, and the actions...

49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

Code of Federal Regulations, 2013 CFR

2013-10-01

.... Because the operator will not become familiar with the detailed design of all new bus models that are tested, tests to determine the time and skill required to remove and reinstall an engine, a transmission... feasible to conduct statistical reliability tests. The detected bus failures, repair time, and the actions...

49 CFR 605.12 - Use of project equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., facilities or equipment funded under the Acts. A grantee or operator may, however, use such buses, facilities... 49 Transportation 7 2010-10-01 2010-10-01 false Use of project equipment. 605.12 Section 605.12..., DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.12 Use of project equipment...

Radiation-Tolerant Dual Data Bus

NASA Technical Reports Server (NTRS)

Kinstler, Gary A.

2007-01-01

An architecture, and a method of utilizing the architecture, have been proposed to enable error-free operation of a data bus that includes, and is connected to, commercial off-the-shelf (COTS) circuits and components that are inherently susceptible to singleevent upsets [SEUs (bit flips caused by impinging high-energy particles and photons)]. The architecture and method are applicable, more specifically, to data-bus circuitry based on the Institute for Electrical and Electronics Engineers (IEEE) 1394b standard for a high-speed serial bus.

Paratransit and Transit Integration Areawide Demand Responsive Transportation System - Program Analysis

DOT National Transportation Integrated Search

1977-04-01

The Urban Mass Transportation Administration carries out research and developmet on Areawide Demand Responsive Transportation (AWDRT) systems as part of the Bus and Paratransit Technoloy activities. AWDRT systems are basically the interation of flexi...

Heterogeneity of passenger exposure to air pollutants in public transport microenvironments

NASA Astrophysics Data System (ADS)

Yang, Fenhuan; Kaul, Daya; Wong, Ka Chun; Westerdahl, Dane; Sun, Li; Ho, Kin-fai; Tian, Linwei; Brimblecombe, Peter; Ning, Zhi

2015-05-01

Epidemiologic studies have linked human exposure to pollutants with adverse health effects. Passenger exposure in public transport systems contributes an important fraction of daily burden of air pollutants. While there is extensive literature reporting the concentrations of pollutants in public transport systems in different cities, there are few studies systematically addressing the heterogeneity of passenger exposure in different transit microenvironments, in cabins of different transit vehicles and in areas with different characteristics. The present study investigated PM2.5 (particulate matter with aerodynamic diameters smaller than 2.5 μm), black carbon (BC), ultrafine particles (UFP) and carbon monoxide (CO) pollutant concentrations in various public road transport systems in highly urbanized city of Hong Kong. Using a trolley case housing numerous portable air monitors, we conducted a total of 119 trips during the campaign. Transit microenvironments, classified as 1). busy and secondary roadside bus stops; 2). open and enclosed termini; 3). above- and under-ground Motor Rail Transport (MTR) platforms, were investigated and compared to identify the factors that may affect passenger exposures. The pollutants inside bus and MTR cabins were also investigated together with a comparison of time integrated exposure between the transit modes. Busy roadside and enclosed termini demonstrated the highest average particle concentrations while the lowest was found on the MTR platforms. Traffic-related pollutants BC, UFP and CO showed larger variations than PM2.5 across different microenvironments and areas confirming their heterogeneity in urban environments. In-cabin pollutant concentrations showed distinct patterns with BC and UFP high in diesel bus cabins and CO high in LPG bus cabins, suggesting possible self-pollution issues and/or penetration of on-road pollutants inside cabins during bus transit. The total passenger exposure along selected routes, showed bus trips had the potential for higher integrated passenger exposure compared to MTR trips. The present study may provide useful information to better characterize the distribution of passenger exposure pattern in health assessment studies and the results also highlight the need to formulate exposure reduction based air policies in large cities.

Investigating Geosparql Requirements for Participatory Urban Planning

NASA Astrophysics Data System (ADS)

Mohammadi, E.; Hunter, A. J. S.

2015-06-01

We propose that participatory GIS (PGIS) activities including participatory urban planning can be made more efficient and effective if spatial reasoning rules are integrated with PGIS tools to simplify engagement for public contributors. Spatial reasoning is used to describe relationships between spatial entities. These relationships can be evaluated quantitatively or qualitatively using geometrical algorithms, ontological relations, and topological methods. Semantic web services utilize tools and methods that can facilitate spatial reasoning. GeoSPARQL, introduced by OGC, is a spatial reasoning standard used to make declarations about entities (graphical contributions) that take the form of a subject-predicate-object triple or statement. GeoSPARQL uses three basic methods to infer topological relationships between spatial entities, including: OGC's simple feature topology, RCC8, and the DE-9IM model. While these methods are comprehensive in their ability to define topological relationships between spatial entities, they are often inadequate for defining complex relationships that exist in the spatial realm. Particularly relationships between urban entities, such as those between a bus route, the collection of associated bus stops and their overall surroundings as an urban planning pattern. In this paper we investigate common qualitative spatial reasoning methods as a preliminary step to enhancing the capabilities of GeoSPARQL in an online participatory GIS framework in which reasoning is used to validate plans based on standard patterns that can be found in an efficient/effective urban environment.

Information management system breadboard data acquisition and control system.

NASA Technical Reports Server (NTRS)

Mallary, W. E.

1972-01-01

Description of a breadboard configuration of an advanced information management system based on requirements for high data rates and local and centralized computation for subsystems and experiments to be housed on a space station. The system is to contain a 10-megabit-per-second digital data bus, remote terminals with preprocessor capabilities, and a central multiprocessor. A concept definition is presented for the data acquisition and control system breadboard, and a detailed account is given of the operation of the bus control unit, the bus itself, and the remote acquisition and control unit. The data bus control unit is capable of operating under control of both its own test panel and the test processor. In either mode it is capable of both single- and multiple-message operation in that it can accept a block of data requests or update commands for transmission to the remote acquisition and control unit, which in turn is capable of three levels of data-handling complexity.

Replacement model of city bus: A dynamic programming approach

NASA Astrophysics Data System (ADS)

Arifin, Dadang; Yusuf, Edhi

2017-06-01

This paper aims to develop a replacement model of city bus vehicles operated in Bandung City. This study is driven from real cases encountered by the Damri Company in the efforts to improve services to the public. The replacement model propounds two policy alternatives: First, to maintain or keep the vehicles, and second is to replace them with new ones taking into account operating costs, revenue, salvage value, and acquisition cost of a new vehicle. A deterministic dynamic programming approach is used to solve the model. The optimization process was heuristically executed using empirical data of Perum Damri. The output of the model is to determine the replacement schedule and the best policy if the vehicle has passed the economic life. Based on the results, the technical life of the bus is approximately 20 years old, while the economic life is an average of 9 (nine) years. It means that after the bus is operated for 9 (nine) years, managers should consider the policy of rejuvenation.

[Investigation on events of bus on fire in 6 years in the mainland of China].

PubMed

Wang, X G; Liu, Y; Cen, Y; Wu, P; Zhou, H L; Han, C M

2016-12-20

Objective: To retrospectively analyze the characteristics of events of bus on fire in 6 years in the mainland of China. Methods: Events of bus on fire happened between January 2009 and December 2014 were retrieved through Baidu search engine, Chinese Journals Full - text Database, and PubMed database in the search strategy with " bus" and " fire" or " arson" as keywords combined with the name of provinces, autonomous regions, and municipalities of the mainland of China. The occurrence time, region, cause of fire, casualties of each event were recorded, and the correlative analysis was conducted. Data were processed with Microsoft Excel software. Results: Totally 287 events of bus on fire were retrieved, among which 49 events happened in 2009, 36 events happened in 2010, 35 events happened in 2011, 37 events happened in 2012, and respectively 65 events happened in 2013 and 2014. The events of bus on fire most frequently happened in June and July, respectively 49 and 39 events. Among the distribution of occurrence regions of events of bus on fire, there were 78 events (27.18%) in east China, 52 events (18.12%) in northeast China, 41 events (14.29%) both in north China and south China. Among the causes of events of bus on fire, spontaneous combustion of bus ranked in the first (267 events, accounting for 93.03%), followed by arson (13 events, accounting for 4.53%). Among the 13 events of bus on fire caused by arson, 7 events happened between 16: 00 and 20: 00, and 3 events happened between 8: 00 and 10: 00. Totally 27 events of bus on fire (9.41%) were with casualties, among which 13 events (48.15%) were caused by spontaneous combustion of bus, 10 events (37.04%) were caused by arson, and 4 events (14.81%) were caused by traffic accidents. Arson caused the most severe casualties (at least 88 deaths and 287 injuries), followed by spontaneous combustion of bus (at least 35 deaths and 140 injuries) and traffic accidents (at least 9 deaths and 20 injuries). Conclusions: Events of bus on fire happened more frequently in recent years in the mainland of China, and the frequencies were much higher especially in June and July. Most events were caused by spontaneous combustion of bus, followed by arson. Most of the events of bus on fire caused by arson happened in the morning and evening rush hours of urban traffic, and althouth the occurrence rate was not high, the casualties were most severe.

Lagrangian Hotspots of In-Use NOX Emissions from Transit Buses.

PubMed

Kotz, Andrew J; Kittelson, David B; Northrop, William F

2016-06-07

In-use, spatiotemporal NOX emissions were measured from a conventional powertrain transit bus and a series electric hybrid bus over gradients of route kinetic intensity and ambient temperature. This paper introduces a new method for identifying NOX emissions hotspots along a bus route using high fidelity Lagrangian vehicle data to explore spatial interactions that may influence emissions production. Our study shows that the studied transit buses emit higher than regulated emissions because on-route operation does not accurately represent the range of engine operation tested according to regulatory standards. Using the Lagrangian hotspot detection, we demonstrate that NOX hotspots occurred at bus stops, during cold starts, on inclines, and for accelerations. On the selected routes, bus stops resulted in 3.3 times the route averaged emissions factor in grams/km without significant dependence on bus type or climate. The buses also emitted 2.3 times the route averaged NOX emissions factor at the beginning of each route due to cold selective catalytic reduction aftertreatment temperature. The Lagrangian hotspot detection technique demonstrated here could be employed in future connected vehicles empowered by advances in computational power, data storage capability, and improved sensor technology to optimize emissions as a function of spatial location.

Is there a pattern in European bus and coach incidents? A literature analysis with special focus on injury causation and injury mechanisms.

PubMed

Albertsson, Pontus; Falkmer, Torbjörn

2005-03-01

In order to identify and describe a pattern in bus and coach incident related injuries and fatalities, and to suggest possible future measures for improvement of bus and coach safety, a literature analysis was performed. The results formed a multi-faceted pattern, which briefly can be described as follows; women travelled more frequently by bus as compared to men. Injuries sustained predominantly affected women 60 years of age and older. Of all traffic fatalities in Europe, bus and coach fatalities represented 0.3-0.5%. In the OECD countries, the risk of being killed or seriously injured was found to be seven to nine times lower for bus and coach occupants as compared to those of car occupants. Despite the fact that fatalities were more frequent on rural roads, a vast majority of all bus and coach casualties occurred on urban roads and in dry weather conditions. Boarding and alighting caused about one-third of all injury cases. Collisions were a major injury-contributing factor. Buses and coaches most frequently collided with cars, but unprotected road users were hit in about one-third of all cases of a collision, the point of impact on the bus or the coach being typically frontal or side. Rollovers occurred in almost all cases of severe coach crashes. In this type of crash projection, total ejection, partial ejection, intrusion and smoke inhalation were the main injury mechanisms and among those, ejection being the most dangerous. A 2-point belt may prevent passenger ejection, but in frontal crashes when the upper abdominal parts and the head hit the seatback in front, it could, however, contribute to head and thoracic injuries. Hence, a 3-point belt provides the best restraint in rollovers and frontal crashes.

Occupational exposure to roadway emissions and inside informal settlements in sub-Saharan Africa: A pilot study in Nairobi, Kenya

PubMed Central

Ngo, Nicole S.; Gatari, Michael; Yan, Beizhan; Chillrud, Steven N.; Bouhamam, Kheira; Kinneym, Patrick L.

2015-01-01

Few studies examine urban air pollution in sub-Saharan Africa (SSA), yet urbanization rates there are among the highest in the world. In this study, we measured 8-hr average occupational exposure levels of fine particulate matter (PM2.5), black carbon (BC), ultra violet active-particulate matter (UV-PM), and trace elements for individuals who worked along roadways in Nairobi, specifically bus drivers, garage workers, street vendors, and women who worked inside informal settlements. We found BC and re-suspended dust were important contributors to PM2.5 levels for all study populations, particularly among bus drivers, while PM2.5 exposure levels for garage workers, street vendors, and informal settlement residents were not statistically different from each other. We also found a strong signal for biomass emissions and trash burning, which is common in Nairobi’s low-income areas and open-air garages. These results suggest that the large portion of urban residents in SSA who walk along roadways would benefit from air quality regulations targeting roadway emissions from diesel vehicles, dust, and trash burning. This is the first study to measure occupational exposure to urban air pollution in SSA and results imply that roadway emissions are a serious public health concern. PMID:26034383

Occupational exposure to roadway emissions and inside informal settlements in sub-Saharan Africa: A pilot study in Nairobi, Kenya

NASA Astrophysics Data System (ADS)

Ngo, Nicole S.; Gatari, Michael; Yan, Beizhan; Chillrud, Steven N.; Bouhamam, Kheira; Kinney, Patrick L.

2015-06-01

Few studies examine urban air pollution in sub-Saharan Africa (SSA), yet urbanization rates there are among the highest in the world. In this study, we measured 8-hr average occupational exposure levels of fine particulate matter (PM2.5), black carbon (BC), ultra violet active-particulate matter (UV-PM), and trace elements for individuals who worked along roadways in Nairobi, specifically bus drivers, garage workers, street vendors, and women who worked inside informal settlements. We found BC and re-suspended dust were important contributors to PM2.5 levels for all study populations, particularly among bus drivers, while PM2.5 exposure levels for garage workers, street vendors, and informal settlement residents were not statistically different from each other. We also found a strong signal for biomass emissions and trash burning, which is common in Nairobi's low-income areas and open-air garages. These results suggest that the large portion of urban residents in SSA who walk along roadways would benefit from air quality regulations targeting roadway emissions from diesel vehicles, dust, and trash burning. This is the first study to measure occupational exposure to urban air pollution in SSA and results imply that roadway emissions are a serious public health concern.

Occupational exposure to roadway emissions and inside informal settlements in sub-Saharan Africa: A pilot study in Nairobi, Kenya.

PubMed

Ngo, Nicole S; Gatari, Michael; Yan, Beizhan; Chillrud, Steven N; Bouhamam, Kheira; Kinneym, Patrick L

2015-06-01

Few studies examine urban air pollution in sub-Saharan Africa (SSA), yet urbanization rates there are among the highest in the world. In this study, we measured 8-hr average occupational exposure levels of fine particulate matter (PM 2.5 ), black carbon (BC), ultra violet active-particulate matter (UV-PM), and trace elements for individuals who worked along roadways in Nairobi, specifically bus drivers, garage workers, street vendors, and women who worked inside informal settlements. We found BC and re-suspended dust were important contributors to PM 2.5 levels for all study populations, particularly among bus drivers, while PM 2.5 exposure levels for garage workers, street vendors, and informal settlement residents were not statistically different from each other. We also found a strong signal for biomass emissions and trash burning, which is common in Nairobi's low-income areas and open-air garages. These results suggest that the large portion of urban residents in SSA who walk along roadways would benefit from air quality regulations targeting roadway emissions from diesel vehicles, dust, and trash burning. This is the first study to measure occupational exposure to urban air pollution in SSA and results imply that roadway emissions are a serious public health concern.

Urban air quality comparison for bus, tram, subway and pedestrian commutes in Barcelona.

PubMed

Moreno, Teresa; Reche, Cristina; Rivas, Ioar; Cruz Minguillón, Maria; Martins, Vânia; Vargas, Concepción; Buonanno, Giorgio; Parga, Jesus; Pandolfi, Marco; Brines, Mariola; Ealo, Marina; Sofia Fonseca, Ana; Amato, Fulvio; Sosa, Garay; Capdevila, Marta; de Miguel, Eladio; Querol, Xavier; Gibbons, Wes

2015-10-01

Access to detailed comparisons in air quality variations encountered when commuting through a city offers the urban traveller more informed choice on how to minimise personal exposure to inhalable pollutants. In this study we report on an experiment designed to compare atmospheric contaminants inhaled during bus, subway train, tram and walking journeys through the city of Barcelona. Average number concentrations of particles 10-300 nm in size, N, are lowest in the commute using subway trains (N<2.5×10(4) part. cm(-3)), higher during tram travel and suburban walking (2.5×10(4) cm(-3)5.0×10(4) cm(-3)), with extreme transient peaks at busy traffic crossings commonly exceeding 1.0×10(5) cm(-3) and accompanied by peaks in Black Carbon and CO. Subway particles are coarser (mode 90 nm) than in buses, trams or outdoors (<70 nm), and concentrations of fine particulate matter (PM2.5) and Black Carbon are lower in the tram when compared to both bus and subway. CO2 levels in public transport reflect passenger numbers, more than tripling from outdoor levels to >1200 ppm in crowded buses and trains. There are also striking differences in inhalable particle chemistry depending on the route chosen, ranging from aluminosiliceous at roadsides and near pavement works, ferruginous with enhanced Mn, Co, Zn, Sr and Ba in the subway environment, and higher levels of Sb and Cu inside the bus. We graphically display such chemical variations using a ternary diagram to emphasise how "air quality" in the city involves a consideration of both physical and chemical parameters, and is not simply a question of measuring particle number or mass. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Brake Lining for Transit Buses - Bonded vs. Bolted

DOT National Transportation Integrated Search

1985-06-01

This report points out an often cited complaint from urban transit agencies concerning the Advanced Design Bus: the relatively short brake lining life. Despite design improvements made by the equipment supply industry since the introduction of the AD...

Self Service Fare Collection on Buses in Portland, OR

DOT National Transportation Integrated Search

1986-09-01

In 1980, the Urban Mass Transportation Administration (UMTA) awarded grants to the Tri-County Metropolitan Transportation District (TRI-MET) to implement self-service fare collection (SSFC) on its bus system. TRI-MET, the transit authority serving Po...

Methodology for the analysis of pollutant emissions from a city bus

NASA Astrophysics Data System (ADS)

Armas, Octavio; Lapuerta, Magín; Mata, Carmen

2012-04-01

In this work a methodology is proposed for measurement and analysis of gaseous emissions and particle size distributions emitted by a diesel city bus during its typical operation under urban driving conditions. As test circuit, a passenger transportation line at a Spanish city was used. Different ways for data processing and representation were studied and, derived from this work, a new approach is proposed. The methodology was useful to detect the most important uncertainties arising during registration and processing of data derived from a measurement campaign devoted to determine the main pollutant emissions. A HORIBA OBS-1300 gas analyzer and a TSI engine exhaust particle spectrometer were used with 1 Hz frequency data recording. The methodology proposed allows for the comparison of results (in mean values) derived from the analysis of either complete cycles or specific categories (or sequences). The analysis by categories is demonstrated to be a robust and helpful tool to isolate the effect of the main vehicle parameters (relative fuel-air ratio and velocity) on pollutant emissions. It was shown that acceleration sequences have the highest contribution to the total emissions, whereas deceleration sequences have the least.

MIL-STD-1553 dynamic bus controller/remote terminal hybrid set

NASA Astrophysics Data System (ADS)

Friedman, S. N.

This paper describes the performance, physical and electrical requirements of a Dual Redundant BUS Interface Unit (BIU) acting as a BUS Controller Interface Unit (BCIU) or Remote Terminal Unit (RTU) between a Motorola 68000 VME BUS and MIL-STD-1553B Multiplex Data Bus. A discussion of how the BIU Hybrid set is programmed, and operates as a BCIU or RTU, will be included. This paper will review Dynamic Bus Control and other Mode Code capabilities. The BIU Hybrid Set interfaces to a 68000 Microprocessor with a VME Bus using programmed I/O transfers. This special interface will be discussed along with the internal Dual Access Memory (4K x 16) used to support the data exchanges between the CPU and the BIU Hybrid Set. The hybrid set's physical size and power requirements will be covered. This includes the present Double Eurocard the BIU function is presently being offered on.

Fault tolerant data management system

NASA Technical Reports Server (NTRS)

Gustin, W. M.; Smither, M. A.

1972-01-01

Described in detail are: (1) results obtained in modifying the onboard data management system software to a multiprocessor fault tolerant system; (2) a functional description of the prototype buffer I/O units; (3) description of modification to the ACADC and stimuli generating unit of the DTS; and (4) summaries and conclusions on techniques implemented in the rack and prototype buffers. Also documented is the work done in investigating techniques of high speed (5 Mbps) digital data transmission in the data bus environment. The application considered is a multiport data bus operating with the following constraints: no preferred stations; random bus access by all stations; all stations equally likely to source or sink data; no limit to the number of stations along the bus; no branching of the bus; and no restriction on station placement along the bus.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

PubMed Central

2018-01-01

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety. PMID:29534530

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers.

PubMed

Montoro, Luis; Useche, Sergio; Alonso, Francisco; Cendales, Boris

2018-03-12

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

Programmable DMA controller

NASA Technical Reports Server (NTRS)

Hendry, David F. (Inventor)

1993-01-01

In a data system having a memory, plural input/output (I/O) devices and a bus connecting each of the I/O devices to the memory, a direct memory access (DMA) controller regulating access of each of the I/O devices to the bus, including a priority register storing priorities of bus access requests from the I/O devices, an interrupt register storing bus access requests of the I/O devices, a resolver for selecting one of the I/O devices to have access to the bus, a pointer register storing addresses of locations in the memory for communication with the one I/O device via the bus, a sequence register storing an address of a location in the memory containing a channel program instruction which is to be executed next, an ALU for incrementing and decrementing addresses stored in the pointer register, computing the next address to be stored in the sequence register, computing an initial contents of each of the register. The memory contains a sequence of channel program instructions defining a set up operation wherein the contents of each of the registers in the channel register is initialized in accordance with the initial contents computed by the ALU and an access operation wherein data is transferred on the bus between a location in the memory whose address is currently stored in the pointer register and the one I/O device enabled by the resolver.

Systems evaluation of thermal bus concepts

NASA Technical Reports Server (NTRS)

Stalmach, D. D.

1982-01-01

Thermal bus concepts, to provide a centralized thermal utility for large, multihundred kilowatt space platforms, were studied and the results are summarized. Concepts were generated, defined, and screened for inclusion in system level thermal bus trades. Parametric trade studies were conducted in order to define the operational envelope, performance, and physical characteristics of each. Two concepts were selected as offering the most promise for thermal bus development. All of four concepts involved two phase flow in order to meet the required isothermal nature of the thermal bus. Two of the concepts employ a mechanical means to circulate the working fluid, a liquid pump in one case and a vapor compressor in another. Another concept utilizes direct osmosis as the driving force of the thermal bus. The fourth concept was a high capacity monogroove heat pipe. After preliminary sizing and screening, three of these concepts were selected to carry into the trade studies. The monogroove heat pipe concept was deemed unsuitable for further consideration because of its heat transport limitations. One additional concept utilizing capillary forces to drive the working fluid was added. Parametric system level trade studies were performed. Sizing and weight calculations were performed for thermal bus sizes ranging from 5 to 350 kW and operating temperatures in the range of 4 to 120 C. System level considerations such as heat rejection and electrical power penalties and interface temperature losses were included in the weight calculations.

Implementation of a Cooking Bus intervention to support cooking in schools in Wales, UK

PubMed Central

Segrott, Jeremy; Holliday, Jo; Murphy, Simon; Macdonald, Sarah; Roberts, Joan; Moore, Laurence; Phillips, Ceri

2017-01-01

Purpose The teaching of cooking is an important aspect of school-based efforts to promote healthy diets among children, and is frequently done by external agencies. Within a limited evidence base relating to cooking interventions in schools, there are important questions about how interventions are integrated within school settings. The purpose of this paper is to examine how a mobile classroom (Cooking Bus) sought to strengthen connections between schools and cooking, and drawing on the concept of the sociotechnical network, theorise the interactions between the Bus and school contexts. Design/methodology/approach Methods comprised a postal questionnaire to 76 schools which had received a Bus visit, and case studies of the Bus’ work in five schools, including a range of school sizes and urban/rural locations. Case studies comprised observation of Cooking Bus sessions, and interviews with school staff. Findings The Cooking Bus forged connections with schools through aligning intervention and schools’ goals, focussing on pupils’ cooking skills, training teachers and contributing to schools’ existing cooking-related activities. The Bus expanded its sociotechnical network through post-visit integration of cooking activities within schools, particularly teachers’ use of intervention cooking kits. Research limitations/implications The paper highlights the need for research on the long-term impacts of school cooking interventions, and better understanding of the interaction between interventions and school contexts. Originality/value This paper adds to the limited evidence base on school-based cooking interventions by theorising how cooking interventions relate to school settings, and how they may achieve integration. PMID:28725120

Commuter exposure to black carbon particles on diesel buses, on bicycles and on foot: a case study in a Brazilian city.

PubMed

Targino, Admir Créso; Rodrigues, Marcos Vinicius C; Krecl, Patricia; Cipoli, Yago Alonso; Ribeiro, João Paulo M

2018-01-01

Commuting in urban environments accounts for a large fraction of the daily dose of inhaled air pollutants, especially in countries where vehicles have old technologies or run on dirty fuels. We measured black carbon (BC) concentrations during bus, walk and bicycle commutes in a Brazilian city and found a large spatial variability across the surveyed area, with median values between 2.5 and 12.0 μg m -3 . Traffic volume on roadways (especially the number of heavy-duty diesel vehicles), self-pollution from the bus tailpipe, number of stops along the route and displacement speed were the main drivers of air pollution on the buses. BC concentrations increased abruptly at or close to traffic signals and bus stops, causing in-cabin peaks as large as 60.0 μg m -3 . BC hotspots for the walk mode coincided with the locations of bus stops and traffic signals, whilst measurements along a cycle lane located 12 m from the kerb were less affected. The median BC concentrations of the two active modes were significantly lower than the concentrations inside the bus, with a bus/walk and bus/bicycle ratios of up to 6. However, the greater inhalation rates of cyclist and pedestrians yielded larger doses (2.6 and 3.5 μg on a 1.5-km commute), suggesting that the greater physical effort during the active commute may outweigh the reduction in exposure due to the shift from passive to active transport modes.

Efficiency in bus stop location and design.

DOT National Transportation Integrated Search

1980-01-01

The research reported here identified those elements associated with the location and design of bus stops that affect the efficiency of transit and traffic operations, and developed guidelines to assist transportation engineers and planners in techni...

Serramonte Transit Center Study

DOT National Transportation Integrated Search

1983-06-01

The purposes of the study are to determine, from this particular case -- the : Serramonte Center Plan -- guidelines for achieving the successful design and : operation of a bus station and bus access arrangement on a shopping center site, : including...

Impacts of CTfastrak on Real Estate and Urban Economic Development : Phase 1

DOT National Transportation Integrated Search

2017-07-30

CTfastrak, a bus rapid transit service connecting four municipalities (Hartford, West Hartford, Newington, and New Britain) in Central Connecticut (CT), received final funding approval in 2011 and opened for service in March 2015. This new service ma...

Autonomous dial-a-ride transit : benefit-cost evaluation

DOT National Transportation Integrated Search

1998-08-01

Among public transit and for-hire modes, fixed-route bus and rail are most effective in maintaining high ridership in high density areas such as urban centers. The cost effectiveness of fixed-route transit, however, depends on close proximity to the ...

Integrating light rail transit into traditional bus systems

DOT National Transportation Integrated Search

2007-07-01

This document identifies those dynamics that facilitate a citys addition of light rail as a successful component of its urban system, with success deemed to be opening on schedule with minimal start-up issues. The study examines several new system...

User-Side Subsidies for the Elderly and Handicapped in Lawrence, Massachusetts

DOT National Transportation Integrated Search

1984-06-01

Funding provided by the Service and Methods Demonstration (SMD) Program of the U.S. Department of Transportation, Urban Mass Transportation Administration, was used to subsidize the bus, taxicab, and wheelchair lift-equipped van travel of elderly and...

40 CFR 85.1413 - Decertification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Decertification. 85.1413 Section 85.1413 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1413 Decertification. (a...

40 CFR 85.1402 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1402 Definitions. The definitions of this... of Mobile Sources—Office of Air and Radiation of the Environmental Protection Agency. Office Director...

[Development and evaluation of a small group-based cardiocerebrovascular disease prevention education program for male bus drivers].

PubMed

Kim, Eun Young; Hwang, Seon Young

2012-06-01

This study was conducted to examine effects of a small group-based cardiocerebrovascular disease (CVD) prevention education program on knowledge, stage of change and health behavior among male bus drivers with CVD risk factors. A non-equivalent control group pretest-posttest design was used. Participants were 68 male bus drivers recruited from two urban bus companies. Participants from the two groups were selected by matching age, education and risk factors. Experimental group (n=34) received a small group-based CVD prevention education program 8 times over 6 weeks and 3 times through telephone interviews at 2-week intervals. Data were collected between December, 2010 and March, 2011, and were analyzed using chi-square test, t-test, and repeated measure analysis of variance with SPSS/Win18.0. Experimental group showed significantly higher scores in CVD prevention knowledge (p<.001) and health behavior (p<.001) at 6 and 12 weeks after intervention. Participants in pre-contemplation and contemplation stages made progress to contemplation and action. This was significantly better at 6 and 12 weeks after intervention (p<.001). Results suggest that small group-based education programs for CVD prevention are effective in increasing knowledge, stage of change, and health behavior to prevent CVD among male bus drivers with CVD risk.

An estimation of traffic related CO2 emissions from motor vehicles in the capital city of, Iran

PubMed Central

2012-01-01

Vehicle exhaust is a major source of anthropogenic carbon dioxide (CO2) in metropolitan cities. Popular community mode (buses and taxies) and about 2.4 million private cars are the main emission sources of air pollution in Tehran. A case survey has conducted to measure CO2 in four popular vehicles, bus, taxi, private car and motorcycle, which moved in the city with respectively 7800, 82358, 560000 and 2.4 million per day in 2012. Results indicated that the contribution of CO2 emissions increased in the following order: private car, motorcycle, bus and taxi. The overall average for the contribution of CO2 emissions in the private car, motorcycle, bus, and taxi were 26372, 1648, 1433 and 374 tons per day, respectively. Our results also showed that the urban transport operation consume an estimated 178 and 4224 million liter diesel and petrol per year, respectively, that have released about 10 million tons of CO2. The average contribution of CO2 emissions of private cars in Tehran was higher (88%) than other vehicles. It was concluded that high volume of traffic, transport consumption of fossil fuels and shortage of adequate public transport system are responsible for the high CO2 level in environment in Tehran. Thus, it is to be expected that CO2 as a greenhouse gas has risen in Tehran more than ever in the following years and this would be a matter of concern for the authorities to have a comprehensive plan to mitigate this phenomena. PMID:23369252

An estimation of traffic related CO2 emissions from motor vehicles in the capital city of, Iran.

PubMed

Kakouei, Aliakbar; Vatani, Ali; Idris, Ahmed Kamal Bin

2012-11-28

Vehicle exhaust is a major source of anthropogenic carbon dioxide (CO2) in metropolitan cities. Popular community mode (buses and taxies) and about 2.4 million private cars are the main emission sources of air pollution in Tehran. A case survey has conducted to measure CO2 in four popular vehicles, bus, taxi, private car and motorcycle, which moved in the city with respectively 7800, 82358, 560000 and 2.4 million per day in 2012. Results indicated that the contribution of CO2 emissions increased in the following order: private car, motorcycle, bus and taxi. The overall average for the contribution of CO2 emissions in the private car, motorcycle, bus, and taxi were 26372, 1648, 1433 and 374 tons per day, respectively. Our results also showed that the urban transport operation consume an estimated 178 and 4224 million liter diesel and petrol per year, respectively, that have released about 10 million tons of CO2. The average contribution of CO2 emissions of private cars in Tehran was higher (88%) than other vehicles. It was concluded that high volume of traffic, transport consumption of fossil fuels and shortage of adequate public transport system are responsible for the high CO2 level in environment in Tehran. Thus, it is to be expected that CO2 as a greenhouse gas has risen in Tehran more than ever in the following years and this would be a matter of concern for the authorities to have a comprehensive plan to mitigate this phenomena.

Variability of particle number emissions from diesel and hybrid diesel-electric buses in real driving conditions.

PubMed

Sonntag, Darrell B; Gao, H Oliver; Holmén, Britt A

2008-08-01

A linear mixed model was developed to quantify the variability of particle number emissions from transit buses tested in real-world driving conditions. Two conventional diesel buses and two hybrid diesel-electric buses were tested throughout 2004 under different aftertreatments, fuels, drivers, and bus routes. The mixed model controlled the confounding influence of factors inherent to on-board testing. Statistical tests showed that particle number emissions varied significantly according to the after treatment, bus route, driver, bus type, and daily temperature, with only minor variability attributable to differences between fuel types. The daily setup and operation of the sampling equipment (electrical low pressure impactor) and mini-dilution system contributed to 30-84% of the total random variability of particle measurements among tests with diesel oxidation catalysts. By controlling for the sampling day variability, the model better defined the differences in particle emissions among bus routes. In contrast, the low particle number emissions measured with diesel particle filters (decreased by over 99%) did not vary according to operating conditions or bus type but did vary substantially with ambient temperature.

Solutions to Improve Person Transport System in the Pitesti City by Analyzing Public Transport vs. Private Transport

NASA Astrophysics Data System (ADS)

Mihaela, Istrate; Alexandru, Boroiu; Viorel, Nicolae; Ionel, Vieru

2017-10-01

One of the major problems facing the Pitesti city is the road congestion that occurs in the central area of the city during the peak hours. With all the measures taken in recent years - the widening of road arteries, increasing the number of parking spaces, the creation of overground road passages - it is obvious that the problem can only be solved by a new philosophy regarding urban mobility: it is no longer possible to continue through solutions to increase the accessibility of the central area of the city, but it is necessary, on the contrary, to promote a policy of discouraging the penetration of vehicles in the city center, coupled with a policy of improving the connection between urban public transport and county public transport. This new approach is also proposed in the new Urban Mobility Plan of Pitesti city, under development. The most convincing argument for the necessity of this new orientation in the Pitesti city mobility plan is based on the analysis of the current situation of passenger transport on the territory of Pitesti city: the analysis of “public transport versus private transport” reveals a very low occupancy rate for cars and the fact that the road surface required for a passenger (the dynamic area) is much higher in the case of private transport than in the case of public transport. Measurements of passenger flows and vehicle flows on the 6 penetration ways in the city have been made and the calculations clearly demonstrate the benefits of an urban public transport system connected by “transshipment buses” to be made at the edge of the city, to the county public transport system. In terms of inter-county transport, it will continue to be connected to the urban public transport system by existing bus Station, within the city: South Bus Station and North Bus Station. The usefulness of the paper is that it identifies the solutions for sustainable mobility in Pitesti city and proposes concrete solutions for the development of the integrated passenger transport system.

Understanding & modeling bus transit driver availability.

DOT National Transportation Integrated Search

2014-07-01

Bus transit agencies are required to hire extraboard (i.e. back-up) operators to account for unexpected absences. Incorrect sizing of extra driver workforce is problematic for a number of reasons. Overestimating the appropriate number of extraboard o...

Accessible Fixed Route Bus Service Experience

DOT National Transportation Integrated Search

1981-05-01

The research report discusses the operator and user experience with lifting devices on regular bus transit services that facilitate the entry and exit of wheelchair users and semi-ambulatory passengers. The study draws data mainly from experiences at...

San Diego Wheelchair Accessible Bus Study

DOT National Transportation Integrated Search

1977-09-01

The study describes the implementation and early operation of a pilot project of fixed route, wheelchair accessible bus service on two routes of the San Diego Transit system. Five buses of the Transit Authority fleet were retrofitted with wheelchair ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Eudy, L.

This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

Increasing throughput of multiplexed electrical bus in pipe-lined architecture

DOEpatents

Asaad, Sameh; Brezzo, Bernard V; Kapur, Mohit

2014-05-27

Techniques are disclosed for increasing the throughput of a multiplexed electrical bus by exploiting available pipeline stages of a computer or other system. For example, a method for increasing a throughput of an electrical bus that connects at least two devices in a system comprises introducing at least one signal hold stage in a signal-receiving one of the two devices, such that a maximum frequency at which the two devices are operated is not limited by a number of cycles of an operating frequency of the electrical bus needed for a signal to propagate from a signal-transmitting one of the two devices to the signal-receiving one of the two devices. Preferably, the signal hold stage introduced in the signal-receiving one of the two devices is a pipeline stage re-allocated from the signal-transmitting one of the two devices.

EMI/EMP Resistant Data Bus

DTIC Science & Technology

1976-09-01

Control Multiplex Terminal Unit (CMTU) 1 each MTU Test Set 2 each CMTU Test Set 1 each 9 port Radial Coupler 1 each Fiber Optics Radial...Introduction 3 2 . MTU 11 3. CMTU 1 ? 4. SSIU and Controller ?! 5. Optical Data Bus 21 II System Design Construction 24 1 . Optoelectronic...8217 TABLE OF CONTENTS (Continued) SECTION TITLE PAGE IV System Test and Operation 1 . Test Equipment 2 . Evaluation a. Optical Bus b. Optoelectronic

Urinary 1-hydroxypyrene and mutagenicity in bus drivers and mail carriers exposed to urban air pollution in Denmark.

PubMed

Hansen, Ase Marie; Wallin, Håkan; Binderup, Mona Lise; Dybdahl, Marianne; Autrup, Herman; Loft, Steffen; Knudsen, Lisbeth Ehlert

2004-01-10

Previous studies in Denmark have shown that bus drivers and tramway employees were at an increased risk for developing several types of cancer and that bus drives from central Copenhagen have high levels of biomarkers of DNA damage. The present study evaluates 1-hydroxypyrene concentrations and mutagenic activity in urine as biomarkers of exposure in non-smoking bus drivers in city and rural areas on a work day and a day off and in non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). Twenty-four hour urine samples were collected on a working day and a day off from 60 non-smoking bus drivers in city and rural areas and from 88 non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). The concentration of 1-hydroxypyrene was measured by means of HPLC and the mutagenic activity was assessed by the Ames assay with Salmonella tester strain YG1021 and S9 mix. The N-acetyltransferase (NAT2) phenotype was used as a biomarker for susceptibility to mutagenic/carcinogenic compounds. Bus drivers excreted more 1-hydroxypyrene in urine than did mail carriers. The differences were slightly smaller when NAT2 phenotype, cooking at home, exposure to vehicle exhaust, and performing physical exercise after work were included. The NAT2 slow acetylators had 29% (1.29 [CI: 1.15-1.98]) higher 1-hydroxypyrene concentrations in urine than the fast acetylators. Male bus drivers had 0.92 revertants/mol creatinine [CI: 0.37-1.47] and female bus drivers 1.90 revertants/mol creatinine [CI: 1.01-2.79] higher mutagenic activity in urine than mail carriers. The present study indicates that bus drivers are more exposed to polycyclic aromatic hydrocarbons (PAH) and mutagens than mail carriers. Mail carriers who worked outdoors had higher urinary concentration of 1-hydroxypyrene, a marker of exposure to PAH, than those working indoors. The individual levels of urinary mutagenic activity were not correlated to excretion of 1-hydroxypyrene. This might be due to the fact that the most potent mutagenic compounds in diesel exhaust are not PAH but dinitro-pyrenes. Among bus drivers, fast NAT2 acetylators had higher mutagenic activity in urine than slow NAT2 acetylators and female bus drivers had higher mutagenic activity than male bus drivers.

Combined Simulated Annealing and Genetic Algorithm Approach to Bus Network Design

NASA Astrophysics Data System (ADS)

Liu, Li; Olszewski, Piotr; Goh, Pong-Chai

A new method - combined simulated annealing (SA) and genetic algorithm (GA) approach is proposed to solve the problem of bus route design and frequency setting for a given road network with fixed bus stop locations and fixed travel demand. The method involves two steps: a set of candidate routes is generated first and then the best subset of these routes is selected by the combined SA and GA procedure. SA is the main process to search for a better solution to minimize the total system cost, comprising user and operator costs. GA is used as a sub-process to generate new solutions. Bus demand assignment on two alternative paths is performed at the solution evaluation stage. The method was implemented on four theoretical grid networks of different size and a benchmark network. Several GA operators (crossover and mutation) were utilized and tested for their effectiveness. The results show that the proposed method can efficiently converge to the optimal solution on a small network but computation time increases significantly with network size. The method can also be used for other transport operation management problems.

Short-range evaluation of air pollution near bus and railway stations.

PubMed

Corfa, E; Maury, F; Segers, P; Fresneau, A; Albergel, A

2004-12-01

In the early morning, during workdays, intensive activity is observed at both bus and railway stations. This particular time is critical because of the combination of three factors: (1) simultaneous departure of many buses and trains, (2) cold engines, and, quite frequently, (3) stable meteorological conditions. In our approach, we use ARIA Local, a simulation package applying CFD tools to air pollution modeling, to study different scenarios. The CFD model used in this study is the MERCURE model, developed by Electricite de France. For a bus station, we simulate a typical morning peak hour situation and study in detail how the pollution is accumulated in the station courtyard and the impact on the close vicinity. Two scenarios are presented: one with classical diesel engine and one with buses using AQUAZOL or NGV fuel. The definition of the sources inside the Eulerian grid is described as static linear sources. The total emission is averaged over the mean path driven by the bus from the bus stop to the exit of the bus station. For a railway station, we simulate a situation in a real railway station within the city of Paris. The emission from a diesel "locomotive" and its impact on air quality is computed and compared to the impact of other nonmobile emissions. In this case, the definition of sources is described as mobile point sources following the trajectory of the train. These two scenarios are discussed in an urban context, taking into account the flow around buildings and different meteorological conditions.

Evaluation of emission toxicity of urban bus engines: compressed natural gas and comparison with liquid fuels.

PubMed

Turrio-Baldassarri, Luigi; Battistelli, Chiara Laura; Conti, Luigi; Crebelli, Riccardo; De Berardis, Barbara; Iamiceli, Anna Laura; Gambino, Michele; Iannaccone, Sabato

2006-02-15

Emissions from a spark-ignition (SI) heavy-duty (HD) urban bus engine with a three-way catalyst (TWC), fuelled with compressed natural gas (CNG), were chemically analyzed and tested for genotoxicity. The results were compared with those obtained in a previous study on an equivalent diesel engine, fuelled with diesel oil (D) and a blend of the same with 20% vegetable oil (B20). Experimental procedures were identical, so that emission levels of the CNG engine were exactly comparable to the ones of the diesel engine. The experimental design was focused on carcinogenic compounds and genotoxic activity of exhausts. The results obtained show that the SI CNG engine emissions, with respect to the diesel engine fuelled with D, were nearly 50 times lower for carcinogenic polycyclic aromatic hydrocarbons (PAHs), 20 times lower for formaldehyde, and more than 30 times lower for particulate matter (PM). A 20-30 fold reduction of genotoxic activity was estimated from tests performed. A very high reduction of nitrogen oxides (NO(X)) was also measured. The impact of diesel powered transport on urban air quality, and the potential benefits deriving from the use of CNG for public transport, are discussed.

40 CFR 85.1401 - General applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false General applicability. 85.1401 Section 85.1401 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1401 General...

40 CFR 85.1405 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Applicability. 85.1405 Section 85.1405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1405 Applicability. The provisions of...

40 CFR 85.1411 - Labeling requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Labeling requirements. 85.1411 Section 85.1411 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1411 Labeling...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Certification. 85.1406 Section 85.1406 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1406 Certification. (a) Certification...

Economic Optimization Analysis of Chengdu Electric Community Bus Operation

NASA Astrophysics Data System (ADS)

Yidong, Wang; Yun, Cai; Zhengping, Tan; Xiong, Wan

2018-03-01

In recent years, the government has strongly supported and promoted electric vehicles and has given priority to demonstration and popularization in the field of public transport. The economy of public transport operations has drawn increasing attention. In this paper, Chengdu wireless charging pure electric community bus is used as the research object, the battery, air conditioning, driver’s driving behavior and other economic influence factors were analyzed, and optimizing the operation plan through case data analysis, through the reasonable battery matching and mode of operation to help businesses effectively save operating costs and enhance economic efficiency.

COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Daw, C Stuart; Smith, David E

2016-01-01

The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowestmore » average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.« less

Comprehensive Study of Intercity Bus Service in Nebraska

DOT National Transportation Integrated Search

1988-03-01

This study is prompted by the proposed abandonment of regular-route intercity : bus service across northern Nebraska. The current route, which is operated by : Black Hills Stage Lines, provides service from Omaha through Norfolk and Chadron : to Rapi...

Development of a large bus/small bus decision support tool

DOT National Transportation Integrated Search

2008-02-01

Transit managers continue to strive for greater operating efficiency while maintaining an appropriate balance between cost effectiveness and customer service. Over the past decade, the use of heavy-duty buses smaller than the traditional forty-foot v...

ACTS Operational Performance Review: September 1995

NASA Technical Reports Server (NTRS)

Krawczyk, Richard J.

1996-01-01

The Advanced Communications Technology Satellite (ACTS) utilized a proven spacecraft bus with a payload that qualified new technologies to provide a wide range of on-orbit demonstrations. A comprehensive development, qualification and ground test program was implemented to reduce technology risks. Since launch in September, 1993, and insertion into its geostationary slot ACTS has accumulated over 16,000 hours of successful operation. This paper briefly reviews the technology development background then provides a summary of the operational performance observed for the spacecraft bus and communication payload subsystems and units.

National Fuel Cell Bus Program: Accelerated Testing Evaluation Report #2, Alameda-Contra Costa Transit District (AC Transit) and Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, L.; Chandler, K.

2010-06-01

This is an evaluation of hydrogen fuel cell transit buses operating at AC Transit in revenue service since March 20, 2006, comparing similar diesel buses operating from the same depot. It covers November 2007 through February 2010. Results include implementation experience, fueling station operation, evaluation results at AC Transit (bus usage, availability, fuel economy, maintenance costs, and road calls), and a summary of achievements and challenges encountered during the demonstration.

20 kHz main inverter unit. [for space station power supplies

NASA Technical Reports Server (NTRS)

Hussey, S.

1989-01-01

A proof-of-concept main inverter unit has demonstrated the operation of a pulse-width-modulated parallel resonant power stage topology as a 20-kHz ac power source driver, showing simple output regulation, parallel operation, power sharing and short-circuit operation. The use of a two-stage dc input filter controls the electromagnetic compatibility (EMC) characteristics of the dc power bus, and the use of an ac harmonic trap controls the EMC characteristics of the 20-kHz ac power bus.

Particulates and noise exposure during bicycle, bus and car commuting: A study in three European cities.

PubMed

Okokon, Enembe O; Yli-Tuomi, Tarja; Turunen, Anu W; Taimisto, Pekka; Pennanen, Arto; Vouitsis, Ilias; Samaras, Zissis; Voogt, Marita; Keuken, Menno; Lanki, Timo

2017-04-01

In order to curb traffic-related air pollution and its impact on the physical environment, contemporary city commuters are encouraged to shift from private car use to active or public transport modes. However, personal exposures to particulate matter (PM), black carbon and noise during commuting may be substantial. Therefore, studies comparing exposures during recommended modes of transport versus car trips are needed. We measured personal exposure to various-sized particulates, soot, and noise during commuting by bicycle, bus and car in three European cities: Helsinki in Finland, Rotterdam in the Netherlands and Thessaloniki in Greece using portable monitoring devices. We monitored commonly travelled routes in these cities. The total number of one-way trips yielding data on any of the measured parameters were 84, 72, 94 and 69 for bicycle, bus, closed-window car and open-window car modes, respectively. The highest mean PM 2.5 (85µg/m 3 ), PM 10 (131µg/m 3 ), black carbon (10.9µg/m 3 ) and noise (75dBA) levels were recorded on the bus, bus (again), open-window car and bicycle modes, respectively, all in Thessaloniki, PM and soot concentrations were generally higher during biking and taking a bus than during a drive in a a car with closed windows. Ratios of bike:car PM 10 ranged from 1.1 in Thessaloniki to 2.6 in Helsinki, while bus:car ratios ranged from in 1.0 in Rotterdam to 5.6 in Thessaloniki. Higher noise levels were mostly recorded during bicycle rides. Based on our study, active- and public-transport commuters are often at risk of higher air pollution and noise exposure than private car users. This should be taken into account in urban transportation planning. Copyright © 2017 Elsevier Inc. All rights reserved.

Exposure to particles and nitrogen dioxide among taxi, bus and lorry drivers.

PubMed

Lewné, Marie; Nise, Gun; Lind, Marie-Louise; Gustavsson, Per

2006-03-01

The aims of this study have been to investigate the occurrence of systematic differences in the personal exposure to motor exhaust between different groups of taxi, bus and lorry drivers, and to study if these are influenced by the choice of exposure indicator. We used one indicator of the gaseous phase, nitrogen dioxide (NO(2)), and one of the particle phase (measured by DataRAM), of the exhausts. A total of 121 drivers were included in the study: 39 taxi drivers, 42 bus drivers and 40 lorry drivers. Personal measurements were performed during one working day. Nitrogen dioxide was measured with passive diffusive samplers and particles with Data-RAM, a logging instrument using nephelometric monitoring. The instrument measures particles between 0.1 and 10 microm in size. The average exposure to NO(2) for lorry drivers was 68 microg/m(3); for bus drivers 60 microg/m(3) and for taxi drivers 48 microg/m(3). For particles the exposure was 57 microg/m(3) for lorry drivers, 44 microg/m(3) for bus drivers and 26 microg/m(3) for taxi drivers. The result remained unchanged when exposures were adjusted for variation in urban background levels of NO(2) and particulate matter with an aerodynamic diameter <10 microm (PM(10)). Lorry drivers experienced the highest exposure and taxi drivers the lowest with bus drivers in an intermediate position, regardless of whether NO(2) or particles were used as exposure indicator. The levels of both NO(2) and particles were higher for bus drivers in the city than for them driving in the suburbs. Using diesel or petrol as a fuel for taxis had no influence on the exposure for the drivers, indicating that the taxi drivers' exposure mainly depends on exhaust from surrounding traffic.

Methods of computing steady-state voltage stability margins of power systems

DOEpatents

Chow, Joe Hong; Ghiocel, Scott Gordon

2018-03-20

In steady-state voltage stability analysis, as load increases toward a maximum, conventional Newton-Raphson power flow Jacobian matrix becomes increasingly ill-conditioned so power flow fails to converge before reaching maximum loading. A method to directly eliminate this singularity reformulates the power flow problem by introducing an AQ bus with specified bus angle and reactive power consumption of a load bus. For steady-state voltage stability analysis, the angle separation between the swing bus and AQ bus can be varied to control power transfer to the load, rather than specifying the load power itself. For an AQ bus, the power flow formulation is only made up of a reactive power equation, thus reducing the size of the Jacobian matrix by one. This reduced Jacobian matrix is nonsingular at the critical voltage point, eliminating a major difficulty in voltage stability analysis for power system operations.

Department of Homeland Security Assistance to States and Localities: A Summary and Issues for the 111th Congress

DTIC Science & Technology

2009-02-26

6 Intercity Passenger Rail Program (Amtrak...6 Intercity Bus Security Grant Program................................................................................. 7...for its intercity rail services between high-risk urban areas. 20 U.S. Department of Homeland Security, Federal Emergency Management Agency

Report on Development of Specification for Design and Performance of 40 Ft. Transit Buses

DOT National Transportation Integrated Search

1971-11-01

The purpose of the specification documented in this report is to define the performance requirements of the standard vehicle--a forty foot transit coach--intended to revitalize urban bus fleets over the near-term future. The specification defines the...

40 CFR 85.1414 - Alternative test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Alternative test procedures. 85.1414 Section 85.1414 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1414 Alternative...

40 CFR 85.1408 - Objections to certification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Objections to certification. 85.1408 Section 85.1408 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1408 Objections...

40 CFR 85.1415 - Treatment of confidential information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Treatment of confidential information. 85.1415 Section 85.1415 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1415...

40 CFR 85.1409 - Warranty.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Warranty. 85.1409 Section 85.1409 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1409 Warranty. (a) As a condition of...

40 CFR 85.1410 - Changes after certification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Changes after certification. 85.1410 Section 85.1410 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1410 Changes...

Exploring how to make system safety work in transit

DOT National Transportation Integrated Search

1994-12-01

The New York Metropolitan Transit Authority (MTA) and its operating elements, the New York City Transit Authority (NYCTA), the Long Island Rail Road (LIRR), Metro-North Commuter Railroad, Long Island Bus (LI Bus), and the Staten Island Rapid Transit ...

A statistical analysis of the relationship between land values and freestanding bus facilities.

DOT National Transportation Integrated Search

2010-02-01

Public transit professionals continue to seek methods that offer greater service opportunities, while : not materially increasing the costs of service provision. One strategy is to construct bus transit : centers which operate much like the airline h...

American Fuel Cell Bus Project Evaluation : Second Report

DOT National Transportation Integrated Search

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses (FCEB) operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Admini...

High voltage bus and auxiliary heater control system for an electric or hybrid vehicle

DOEpatents

Murty, Balarama Vempaty

2000-01-01

A control system for an electric or hybrid electric vehicle includes a vehicle system controller and a control circuit having an electric immersion heater. The heater is electrically connected to the vehicle's high voltage bus and is thermally coupled to a coolant loop containing a heater core for the vehicle's climate control system. The system controller responds to cabin heat requests from the climate control system by generating a pulse width modulated signal that is used by the control circuit to operate the heater at a duty cycle appropriate for the amount of cabin heating requested. The control system also uses the heater to dissipate excess energy produced by an auxiliary power unit and to provide electric braking when regenerative braking is not desirable and manual braking is not necessary. The control system further utilizes the heater to provide a safe discharge of a bank of energy storage capacitors following disconnection of the battery or one of the high voltage connectors used to transmit high voltage operating power to the various vehicle systems. The control circuit includes a high voltage clamping circuit that monitors the voltage on the bus and operates the heater to clamp down the bus voltage when it exceeds a pre-selected maximum voltage. The control system can also be used to phase in operation of the heater when the bus voltage exceeds a lower threshold voltage and can be used to phase out the auxiliary power unit charging and regenerative braking when the battery becomes fully charged.

A voltage-controlled superconducting quantum bus

NASA Astrophysics Data System (ADS)

Casparis, Lucas; Pearson, Natalie; KringhøJ, Anders; Larsen, Thorvald; Kuemmeth, Ferdinand; Krogstrup, Peter; Nygard, Jesper; Petersson, Karl; Marcus, Charles

Superconducting qubits couple strongly to microwave photons and can therefore be coupled over long distances through a superconducting cavity acting as a quantum bus. To avoid frequency-crowding it is desirable to turn qubit coupling off while rearranging qubit frequencies. Here, we present experiments with two gatemon qubits coupled through a cavity, which can be tuned by a voltage-controlled superconducting switch. We characterize the bus tunability and demonstrate switchable qubit coupling with an on/off ratio up to 8. We find that pulsing the bus switch on nanosecond timescales results in the apparent loss of qubit coherence. Further work is needed to understand how dynamic control of the tuneable bus affects qubit operation. We acknowledge financial support from Microsoft Project Q, the Danish National Research Foundation and the US Army Research Office.

An analysis of the 1978 Charlottesville on-board bus survey.

DOT National Transportation Integrated Search

1979-01-01

Since the city of Charlottesville began operating its bus service in September 1976, there has been a 20% increase in patronage. City officials were interested in determining the reasons for the increase and any changes in the characteristics of the ...

Side Object Detection Systems Evaluation : Final Evaluation Report.

DOT National Transportation Integrated Search

2008-12-15

Nearly 46 percent of bus accidents across the United States each year occur on the left or right side of the bus. These collisions result in property damage, and they can negatively impact on revenue operations and public perception. The first commer...

49 CFR 605.16 - Notice.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Notice. 605.16 Section 605.16 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.16 Notice. (a) Each applicant who engages or...

49 CFR 605.15 - Content of agreement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Content of agreement. 605.15 Section 605.15 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.15 Content of agreement. (a...

State of bus safety in the U.S. : summary of federal and state regulations.

DOT National Transportation Integrated Search

2014-06-01

This report provides a comprehensive overview of transit bus safety regulations and standards developed by all 50 states, as well as : information on how state departments of transportation (DOT) regulate the maintenance or operation of transit/parat...

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results : Third Report

DOT National Transportation Integrated Search

2014-05-01

This report presents results of a demonstration of 12 fuel cell electric buses (FCEB) operating in Oakland, California. The FCEBs have a fuel cell dominant hybrid electric propulsion system in a series configuration. The bus manufacturerVan Hool...

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration : Second Results Report

DOT National Transportation Integrated Search

2012-07-04

This report presents results of a demonstration of 12 new fuel cell electric buses (FCEB) operating in Oakland, California. The FCEBs have a fuel cell dominant hybrid electric propulsion system in a series configuration. The bus manufacturerVan Ho...

Glacier Going to the Sun Road Rehabilitation Mitigation Shuttle Bus Evaluation.

DOT National Transportation Integrated Search

2008-03-31

As a mitigation measure during reconstruction of the Going to the Sun Road, Glacier National Park operated a shuttle bus system along three routes during the 2007 season. This report presents a multi-dimensional evaluation of the transportation servi...

Life-cycle assessment of diesel, natural gas and hydrogen fuel cell bus transportation systems

NASA Astrophysics Data System (ADS)

Ally, Jamie; Pryor, Trevor

The Sustainable Transport Energy Programme (STEP) is an initiative of the Government of Western Australia, to explore hydrogen fuel cell technology as an alternative to the existing diesel and natural gas public transit infrastructure in Perth. This project includes three buses manufactured by DaimlerChrysler with Ballard fuel cell power sources operating in regular service alongside the existing natural gas and diesel bus fleets. The life-cycle assessment (LCA) of the fuel cell bus trial in Perth determines the overall environmental footprint and energy demand by studying all phases of the complete transportation system, including the hydrogen infrastructure, bus manufacturing, operation, and end-of-life disposal. The LCAs of the existing diesel and natural gas transportation systems are developed in parallel. The findings show that the trial is competitive with the diesel and natural gas bus systems in terms of global warming potential and eutrophication. Emissions that contribute to acidification and photochemical ozone are greater for the fuel cell buses. Scenario analysis quantifies the improvements that can be expected in future generations of fuel cell vehicles and shows that a reduction of greater than 50% is achievable in the greenhouse gas, photochemical ozone creation and primary energy demand impact categories.

Potential development of an intercity passenger transit system in Texas : final project report.

DOT National Transportation Integrated Search

2010-05-01

This report describes the findings of a research study of the potential for development of an intercity rail and : express bus system in the state of Texas. Rather than focus on regional commuter or light rail systems : radiating from urban areas, th...

40 CFR 85.1407 - Notification of intent to certify.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Notification of intent to certify. 85.1407 Section 85.1407 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1407...

Energy efficient motion control of the electric bus on route

NASA Astrophysics Data System (ADS)

Kotiev, G. O.; Butarovich, D. O.; Kositsyn, B. B.

2018-02-01

At present, the urgent problem is the reduction of energy costs of urban motor transport. The article proposes a method of solving this problem by developing an energy-efficient law governing the movement of an electric bus along a city route. To solve this problem, an algorithm is developed based on the dynamic programming method. The proposed method allows you to take into account the constraints imposed on the phase coordinates, control action, as well as on the time of the route. In the course of solving the problem, the model of rectilinear motion of an electric bus on a horizontal reference surface is considered, taking into account the assumptions that allow it to be adapted for the implementation of the method. For the formation of a control action in the equations of motion dynamics, an algorithm for changing the traction / braking torque on the wheels of an electric bus is considered, depending on the magnitude of the control parameter and the speed of motion. An optimal phase trajectory was obtained on a selected section of the road for the prototype of an electric bus. The article presents the comparison of simulation results obtained with the optimal energy efficient control law with the results obtained by a test driver. The comparison proved feasibility of the energy efficient control law for the automobile city electric transport.

Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

DOE PAGES

Gao, Zhiming; Daw, C. Stuart; Smith, David E.; ...

2016-08-01

The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which hasmore » the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.« less

Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Daw, C. Stuart; Smith, David E.

The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which hasmore » the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.« less

Morphology of single inhalable particle inside public transit biodiesel fueled bus.

PubMed

Shandilya, Kaushik K; Kumar, Ashok

2010-01-01

In an urban-transit bus, fueled by biodiesel in Toledo, Ohio, single inhalable particle samples in October 2008 were collected and detected by scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS). Particle size analysis found bimodal distribution at 0.2 and 0.5 microm. The particle morphology was characterized by 14 different shape clusters: square, pentagon, hexagon, heptagon, octagon, nonagon, decagon, agglomerate, sphere, triangle, oblong, strip, line or stick, and unknown, by quantitative order. The square particles were common in the samples. Round and triangle particles are more, and pentagon, hexagon, heptagon, octagon, nonagon, decagon, strip, line or sticks are less. Agglomerate particles were found in abundance. The surface of most particles was coarse with a fractal edge that can provide a suitable chemical reaction bed in the polluted atmospheric environment. The three sorts of surface patterns of squares were smooth, semi-smooth, and coarse. The three sorts of square surface patterns represented the morphological characteristics of single inhalable particles in the air inside the bus in Toledo. The size and shape distribution results were compared to those obtained for a bus using ultra low sulfur diesel.

SAE for the prediction of road traffic status from taxicab operating data and bus smart card data

NASA Astrophysics Data System (ADS)

Zhengfeng, Huang; Pengjun, Zheng; Wenjun, Xu; Gang, Ren

Road traffic status is significant for trip decision and traffic management, and thus should be predicted accurately. A contribution is that we consider multi-modal data for traffic status prediction than only using single source data. With the substantial data from Ningbo Passenger Transport Management Sector (NPTMS), we wished to determine whether it was possible to develop Stacked Autoencoders (SAEs) for accurately predicting road traffic status from taxicab operating data and bus smart card data. We show that SAE performed better than linear regression model and Back Propagation (BP) neural network for determining the relationship between road traffic status and those factors. In a 26-month data experiment using SAE, we show that it is possible to develop highly accurate predictions (91% test accuracy) of road traffic status from daily taxicab operating data and bus smart card data.

Thermal modeling of nickel-hydrogen battery cells operating under transient orbital conditions

NASA Technical Reports Server (NTRS)

Schrage, Dean S.

1991-01-01

An analytical study of the thermal operating characteristics of nickel-hydrogen battery cells is presented. Combined finite-element and finite-difference techniques are employed to arrive at a computationally efficient composite thermal model representing a series-cell arrangement operating in conjunction with a radiately coupled baseplate and coldplate thermal bus. An aggressive, low-mass design approach indicates that thermal considerations can and should direct the design of the thermal bus arrangement. Special consideration is given to the potential for mixed conductive and convective processes across the hydrogen gap. Results of a compressible flow model are presented and indicate the transfer process is suitably represented by molecular conduction. A high-fidelity thermal model of the cell stack (and related components) indicates the presence of axial and radial temperature gradients. A detailed model of the thermal bus reveals the thermal interaction of individual cells and is imperative for assessing the intercell temperature gradients.

49 CFR 605.17 - Certification in lieu of notice.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Certification in lieu of notice. 605.17 Section 605.17 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.17 Certification...

V.C.3 Technology Validation : Fuel Cell Bus Evaluations

DOT National Transportation Integrated Search

2005-01-06

Based on the results of this analysis and the response from the project partners, the SunLine demonstration was deemed to be a success. Although it was a prototype (or pre-commercial) vehicle, the ThunderPower bus operated in revenue service at a rel...

Improved estimation of commuter waiting times using headway and commuter boarding information

NASA Astrophysics Data System (ADS)

Ramli, Muhamad Azfar; Jayaraman, Vasundhara; Kwek, Hyen Chee; Tan, Kian Heong; Lee Kee Khoon, Gary; Monterola, Christopher

2018-07-01

The average amount of waiting time spent by commuters is one of the key indicators of service quality for public bus operations. While actual measurements of actual waiting time is difficult to be done en masse, models of waiting time can be derived from bus headways and these models have been adopted by transport planners in monitoring and regulating service reliability of operators. However, these models are founded on several assumptions on the patterns of commuter arrival which may not be applicable for bus services that experience high demand and heavily fluctuating commuter patterns. Given the availability of granular data on commuter boarding from automated fare collection systems, we propose a new methodology to better estimate the average waiting time of commuters. The formulation is anchored and validated using a three-month dataset from ten selected bus routes in Singapore. Finally, we discuss how our new measure allows for minimization of commuter waiting time through schedule optimization.

High-Speed Ring Bus

NASA Technical Reports Server (NTRS)

Wysocky, Terry; Kopf, Edward, Jr.; Katanyoutananti, Sunant; Steiner, Carl; Balian, Harry

2010-01-01

The high-speed ring bus at the Jet Propulsion Laboratory (JPL) allows for future growth trends in spacecraft seen with future scientific missions. This innovation constitutes an enhancement of the 1393 bus as documented in the Institute of Electrical and Electronics Engineers (IEEE) 1393-1999 standard for a spaceborne fiber-optic data bus. It allows for high-bandwidth and time synchronization of all nodes on the ring. The JPL ring bus allows for interconnection of active units with autonomous operation and increased fault handling at high bandwidths. It minimizes the flight software interface with an intelligent physical layer design that has few states to manage as well as simplified testability. The design will soon be documented in the AS-1393 standard (Serial Hi-Rel Ring Network for Aerospace Applications). The framework is designed for "Class A" spacecraft operation and provides redundant data paths. It is based on "fault containment regions" and "redundant functional regions (RFR)" and has a method for allocating cables that completely supports the redundancy in spacecraft design, allowing for a complete RFR to fail. This design reduces the mass of the bus by incorporating both the Control Unit and the Data Unit in the same hardware. The standard uses ATM (asynchronous transfer mode) packets, standardized by ITU-T, ANSI, ETSI, and the ATM Forum. The IEEE-1393 standard uses the UNI form of the packet and provides no protection for the data portion of the cell. The JPL design adds optional formatting to this data portion. This design extends fault protection beyond that of the interconnect. This includes adding protection to the data portion that is contained within the Bus Interface Units (BIUs) and by adding to the signal interface between the Data Host and the JPL 1393 Ring Bus. Data transfer on the ring bus does not involve a master or initiator. Following bus protocol, any BIU may transmit data on the ring whenever it has data received from its host. There is no centralized arbitration or bus granting. The JPL design provides for autonomous synchronization of the nodes on the ring bus. An address-synchronous latency adjust buffer (LAB) has been designed that cannot get out of synchronization and needs no external input. Also, a priority-driven cable selection behavior has been programmed into each unit on the ring bus. This makes the bus able to connect itself up, according to a maximum redundancy priority system, without the need for computer intervention at startup. Switching around a failed or switched-off unit is also autonomous. The JPL bus provides a map of all the active units for the host computer to read and use for fault management. With regard to timing, this enhanced bus recognizes coordinated timing on a spacecraft as critical and addresses this with a single source of absolute and relative time, which is broadcast to all units on the bus with synchronization maintained to the tens of nanoseconds. Each BIU consists of up to five programmable triggers, which may be programmed for synchronization of events within the spacecraft of instrument. All JPL-formatted data transmitted on the ring bus are automatically time-stamped.

A computerized aircraft battery servicing facility

NASA Technical Reports Server (NTRS)

Glover, Richard D.

1992-01-01

The latest upgrade to the Aerospace Energy Systems Laboratory (AESL) is described. The AESL is a distributed digital system consisting of a central system and battery servicing stations connected by a high-speed serial data bus. The entire system is located in two adjoining rooms; the bus length is approximately 100 ft. Each battery station contains a digital processor, data acquisition, floppy diskette data storage, and operator interfaces. The operator initiates a servicing task and thereafter the battery station monitors the progress of the task and terminates it at the appropriate time. The central system provides data archives, manages the data bus, and provides a timeshare interface for multiple users. The system also hosts software production tools for the battery stations and the central system.

School bus transportation for students seated in wheelchairs.

PubMed

Buning, Mary Ellen; Karg, Patricia E

2011-01-01

For children with Individualized Education Plans (IEPs), transportation is considered a related service and a part of their education. This paper presents an overview of the current status of wheelchair transportation for students on school buses within the United States. The review includes the school transportation environment for wheelchair-seated students, applicable regulations and voluntary standards, primary safety issues for wheelchair-seated students, and key stakeholders roles in improving wheelchair transportation safety. Future actions to improve wheelchair transportation safety in school transportation are discussed, including the need to improve data collection, mandate payment for and use of RESNA WC19-compliant wheelchairs, improve training for bus operators and attendants, and require specialty certification for school bus operators who transport wheelchair-seated students.

Department of Homeland Security Assistance to States and Localities: A Summary and Issues for the 111th Congress

DTIC Science & Technology

2009-04-21

6 Intercity Passenger Rail Program (Amtrak) .....................................................................6... Intercity Bus Security Grant Program..............................................................................7 Trucking Security Program...continue security enhancements for its intercity rail services between high-risk urban areas. 20 U.S. Department of Homeland Security, Federal Emergency

Rural School Busing. ERIC Digest.

ERIC Educational Resources Information Center

Howley, Aimee; Howley, Craig

This digest summarizes information suggesting that long bus rides are part of the hidden costs of school and district consolidation. Rural school districts spend more than twice per pupil what urban districts spend on transportation. A review of studies shows that rural school children were more likely than suburban school children to have bus…

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 86.095-35 - Labeling.

Code of Federal Regulations, 2010 CFR

2010-07-01

... lettered in the English language in block letters and numerals, which shall be of a color that contrasts... following information lettered in the English language in block letters and numerals which shall be of a... chapter. (O) For diesel engines which have been certified to comply with the urban bus particulate...

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation : Third Results Report

DOT National Transportation Integrated Search

2012-05-01

SunLine Transit Agency provides public transit services to the Coachella Valley area of California. SunLine has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. This report describes operations at SunLine for a prototype f...

Bus rapid transit and development : policies and practices that affect development around transit.

DOT National Transportation Integrated Search

2009-12-01

The development of Bus Rapid Transit (BRT) systems is relatively recent in the United States, but several systems are in operation and more are advancing. There is a need for a more comprehensive understanding of the relationship between land use and...

ABA Reauthorization Proposal: Restoring the Balance Between Public and Private Bus Operations

DOT National Transportation Integrated Search

2002-11-01

In preparation for the U.S. Congress' reauthorization of the historic 1998 Transportation Equity Act for the 21st Century (TEA-21), which will take shape between now and Fall 2003, the American Bus Association has created proposals that outline the m...

Fuels for urban transit buses: a cost-effectiveness analysis.

PubMed

Cohen, Joshua T; Hammitt, James K; Levy, Jonathan I

2003-04-15

Public transit agencies have begun to adopt alternative propulsion technologies to reduce urban transit bus emissions associated with conventional diesel (CD) engines. Among the most popular alternatives are emission controlled diesel buses (ECD), defined here to be buses with continuously regenerating diesel particle filters burning low-sulfur diesel fuel, and buses burning compressed natural gas (CNG). This study uses a series of simplifying assumptions to arrive at first-order estimates for the incremental cost-effectiveness (CE) of ECD and CNG relative to CD. The CE ratio numerator reflects acquisition and operating costs. The denominator reflects health losses (mortality and morbidity) due to primary particulate matter (PM), secondary PM, and ozone exposure, measured as quality adjusted life years (QALYs). We find that CNG provides larger health benefits than does ECD (nine vs six QALYs annually per 1000 buses) but that ECD is more cost-effective than CNG (dollar 270 000 per QALY for ECD vs dollar 1.7 million to dollar 2.4 million for CNG). These estimates are subject to much uncertainty. We identify assumptions that contribute most to this uncertainty and propose potential research directions to refine our estimates.

System design of the Pioneer Venus spacecraft. Volume 3: Systems analysis

NASA Technical Reports Server (NTRS)

Fisher, J. N.

1973-01-01

The mission, systems, operations, ground systems, and reliability analysis of the Thor/Delta baseline design used for the Pioneer Space Probe are discussed. Tradeoff decisions concerning spin axis orientation, bus antenna design, communication system design, probe descent, and reduced science payload are analyzed. The reliability analysis is made for the probe bus mission, large probe mission, and small probe mission. Detailed mission sequences were established to identify critical areas and provide phasing of critical operation.

Adult Competency Education Kit. Basic Skills in Speaking, Math, and Reading for Employment. Part R. ACE Competency Based Job Descriptions: #95--Bus Driver; #98--General Loader; #99--Forklift Operator; #100--Material Handler.

ERIC Educational Resources Information Center

San Mateo County Office of Education, Redwood City, CA. Career Preparation Centers.

This fifteenth of fifteen sets of Adult Competency Education (ACE) Competency Based Job Descriptions in the ACE kit contains job descriptions for Bus Driver, General Loader, Forklift Operator, and Material Handler. Each begins with a fact sheet that includes this information: occupational title, D.O.T. code, ACE number, career ladder, D.O.T.…

Multi-Antenna Data Collector for Smart Metering Networks with Integrated Source Separation by Spatial Filtering

NASA Astrophysics Data System (ADS)

Quednau, Philipp; Trommer, Ralph; Schmidt, Lorenz-Peter

2016-03-01

Wireless transmission systems in smart metering networks share the advantage of lower installation costs due to the expandability of separate infrastructure but suffer from transmission problems. In this paper the issue of interference of wireless transmitted smart meter data with third party systems and data from other meters is investigated and an approach for solving the problem is presented. A multi-channel wireless m-bus receiver was developed to separate the desired data from unwanted interferers by spatial filtering. The according algorithms are presented and the influence of different antenna types on the spatial filtering is investigated. The performance of the spatial filtering is evaluated by extensive measurements in a realistic surrounding with several hundreds of active wireless m-bus transponders. These measurements correspond to the future environment for data-collectors as they took place in rural and urban areas with smart gas meters equipped with wireless m-bus transponders installed in almost all surrounding buildings.

Discovering anomalous events from urban informatics data

NASA Astrophysics Data System (ADS)

Jayarajah, Kasthuri; Subbaraju, Vigneshwaran; Weerakoon, Dulanga; Misra, Archan; Tam, La Thanh; Athaide, Noel

2017-05-01

Singapore's "smart city" agenda is driving the government to provide public access to a broader variety of urban informatics sources, such as images from traffic cameras and information about buses servicing different bus stops. Such informatics data serves as probes of evolving conditions at different spatiotemporal scales. This paper explores how such multi-modal informatics data can be used to establish the normal operating conditions at different city locations, and then apply appropriate outlier-based analysis techniques to identify anomalous events at these selected locations. We will introduce the overall architecture of sociophysical analytics, where such infrastructural data sources can be combined with social media analytics to not only detect such anomalous events, but also localize and explain them. Using the annual Formula-1 race as our candidate event, we demonstrate a key difference between the discriminative capabilities of different sensing modes: while social media streams provide discriminative signals during or prior to the occurrence of such an event, urban informatics data can often reveal patterns that have higher persistence, including before and after the event. In particular, we shall demonstrate how combining data from (i) publicly available Tweets, (ii) crowd levels aboard buses, and (iii) traffic cameras can help identify the Formula-1 driven anomalies, across different spatiotemporal boundaries.

49 CFR 665.25 - Transportation of vehicle.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Transportation of vehicle. 665.25 Section 665.25..., DEPARTMENT OF TRANSPORTATION BUS TESTING Operations § 665.25 Transportation of vehicle. A manufacturer shall be responsible for transporting its vehicle to and from the bus testing facility at the beginning and...

49 CFR 665.25 - Transportation of vehicle.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Transportation of vehicle. 665.25 Section 665.25..., DEPARTMENT OF TRANSPORTATION BUS TESTING Operations § 665.25 Transportation of vehicle. A manufacturer shall be responsible for transporting its vehicle to and from the bus testing facility at the beginning and...

49 CFR 605.15 - Content of agreement.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Content of agreement. 605.15 Section 605.15 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.15 Content of agreement. (a) Every grantee who is not authorized by the...

School Bus Safety Advisory Committee: 1999 Annual Report.

ERIC Educational Resources Information Center

Lazenberry, Dennis; Anderson, Barbara

This report summarizes the deliberations and recommendations of Minnesota's School Bus Safety Advisory Committee (SBSAC). The committee, which operates under the auspices of the Minnesota Department of Public Safety, is charged to study issues affecting the safety of students on school buses, arrive at consensus on ways to improve student safety…

Princeton VLSI Project.

DTIC Science & Technology

1983-01-01

34 for these controllers: the remote words required appear On the system bus vithout having been requested, as if the controllers has ExtraSensory ... Perception .) In any case, the processor is not aware of the ESP controller (except for time delays); it operates as if it had a long bus linking it to all

46 CFR 28.360 - Electrical distribution systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Electrical distribution systems. 28.360 Section 28.360... Operate With More Than 16 Individuals on Board § 28.360 Electrical distribution systems. (a) Each electrical distribution system which has a neutral bus or conductor must have the neutral bus or conductor...

46 CFR 28.360 - Electrical distribution systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Electrical distribution systems. 28.360 Section 28.360... Operate With More Than 16 Individuals on Board § 28.360 Electrical distribution systems. (a) Each electrical distribution system which has a neutral bus or conductor must have the neutral bus or conductor...

46 CFR 28.360 - Electrical distribution systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Electrical distribution systems. 28.360 Section 28.360... Operate With More Than 16 Individuals on Board § 28.360 Electrical distribution systems. (a) Each electrical distribution system which has a neutral bus or conductor must have the neutral bus or conductor...

46 CFR 28.360 - Electrical distribution systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Electrical distribution systems. 28.360 Section 28.360... Operate With More Than 16 Individuals on Board § 28.360 Electrical distribution systems. (a) Each electrical distribution system which has a neutral bus or conductor must have the neutral bus or conductor...

Administration of Public School Transportation. School Business Administration Publication No. 6.

ERIC Educational Resources Information Center

California State Dept. of Education, Sacramento. Bureau of Administrative Services.

This document is intended to help California school boards in the selection of an appropriate and adequate student transportation system; and in the establishment, operation, and maintenance of a school bus fleet. Guidelines and pertinent State legislation are given for school bus purchase, maintenance, insurance and replacement; health…

Four-Channel PC/104 MIL-STD-1553 Circuit Board

NASA Technical Reports Server (NTRS)

Cox, Gary L.

2004-01-01

The mini bus interface card (miniBIC) is the first four-channel electronic circuit board that conforms to MIL-STD-1553 and to the electrical-footprint portion of PC/104. [MIL-STD-1553 is a military standard that encompasses a method of communication and electrical- interface requirements for digital electronic subsystems connected to a data bus. PC/104 is an industry standard for compact, stackable modules that are fully compatible (in architecture, hardware, and software) with personal-computer data- and power-bus circuitry.] Prior to the development of the miniBIC, only one- and two-channel PC/104 MIL-STD-1553 boards were available. To obtain four channels, it was necessary to include at least two boards in a PC/104 stack. In comparison with such a two-board stack, the miniBIC takes up less space, consumes less power, and is more reliable. In addition, the miniBIC includes 32 digital input/output channels. The miniBIC (see figure) contains four MIL-STD-1553B hybrid integrated circuits (ICs), four transformers, a field-programmable gate array (FPGA), and an Industry Standard Architecture (ISA) interface. Each hybrid IC includes a MILSTD-1553 dual transceiver, memory-management circuitry, processor interface logic circuitry, and 64Kx16 bits of shared static random access memory. The memory is used to configure message and data blocks. In addition, 23 16-bit registers are available for (1) configuring the hybrid IC for, and starting it in, various modes of operation; (2) reading the status of the functionality of the hybrid IC; and (3) resetting the hybrid IC to a known state. The miniBIC can operate as a remote terminal, bus controller, or bus monitor. The FPGA provides the chip-select and data-strobe signals needed for operation of the hybrid ICs. The FPGA also receives interruption signals and forwards them to the ISA bus. The ISA interface connects the address, data, and control interfaces of the hybrid ICs to the ISA backplane. Each channel is, in effect, a MIL-STD-1553 interface that can operate either independently of the others or else as a redundant version of one of the others. The transformer in each channel provides electrical isolation between the rest of the miniBIC circuitry and the bus to which that channel is connected.

Boeing's STAR-FODB test results

NASA Astrophysics Data System (ADS)

Fritz, Martin E.; de la Chapelle, Michael; Van Ausdal, Arthur W.

1995-05-01

Boeing has successfully concluded a 2 1/2 year, two phase developmental contract for the STAR-Fiber Optic Data Bus (FODB) that is intended for future space-based applications. The first phase included system analysis, trade studies, behavior modeling, and architecture and protocal selection. During this phase we selected AS4074 Linear Token Passing Bus (LTPB) protocol operating at 200 Mbps, along with the passive, star-coupled fiber media. The second phase involved design, build, integration, and performance and environmental test of brassboard hardware. The resulting brassboard hardware successfully passed performance testing, providing 200 Mbps operation with a 32 X 32 star-coupled medium. This hardware is suitable for a spaceflight experiment to validate ground testing and analysis and to demonstrate performace in the intended environment. The fiber bus interface unit (FBIU) is a multichip module containing transceiver, protocol, and data formatting chips, buffer memory, and a station management controller. The FBIU has been designed for low power, high reliability, and radiation tolerance. Nine FBIUs were built and integrated with the fiber optic physical layer consisting of the fiber cable plant (FCP) and star coupler assembly (SCA). Performance and environmental testing, including radiation exposure, was performed on selected FBIUs and the physical layer. The integrated system was demonstrated with a full motion color video image transfer across the bus while simultaneously performing utility functions with a fiber bus control module (FBCM) over a telemetry and control (T&C) bus, in this case AS1773.

Pilot evaluation of a walking school bus program in a low-income, urban community

PubMed Central

Mendoza, Jason A; Levinger, David D; Johnston, Brian D

2009-01-01

Background To evaluate the impact of a walking school bus (WSB) program on student transport in a low-income, urban neighborhood. Methods The design was a controlled, quasi-experimental trial with consecutive cross-sectional assessments. The setting was three urban, socioeconomically disadvantaged, public elementary schools (1 intervention vs. 2 controls) in Seattle, Washington, USA. Participants were ethnically diverse students in kindergarten-5th grade (aged 5–11 years). The intervention was a WSB program consisting of a part-time WSB coordinator and parent volunteers. Students' method of transportation to school was assessed by a classroom survey at baseline and one-year follow-up. The Pearson Chi-squared test compared students transported to school at the intervention versus control schools at each time point. Due to multiple testing, we calculated adjusted p-values using the Ryan-Holm stepdown Bonferroni procedure. McNemar's test was used to examine the change from baseline to 12-month follow-up for walking versus all other forms of school transport at the intervention or control schools. Results At baseline, the proportions of students (n = 653) walking to the intervention (20% +/- 2%) or control schools (15% +/- 2%) did not differ (p = 0.39). At 12-month follow up, higher proportions of students (n = 643, p = 0.001)) walked to the intervention (25% +/- 2%) versus the control schools (7% +/- 1%). No significant changes were noted in the proportion of students riding in a car or taking the school bus at baseline or 12-month follow up (all p > 0.05). Comparing baseline to 12-month follow up, the numbers of students who walked to the intervention school increased while the numbers of students who used the other forms of transport did not change (p < 0.0001). In contrast, the numbers of students who walked to the control schools decreased while the numbers of students who used the other forms of transport did not change (p < 0.0001). Conclusion A WSB program is a promising intervention among urban, low-income elementary school students that may promote favorable changes toward active transport to school. Trial Registration ClinicalTrials.gov NCT00402701 PMID:19413910

A study of Schwarz converters for nuclear powered spacecraft

NASA Technical Reports Server (NTRS)

Stuart, Thomas A.; Schwarze, Gene E.

1987-01-01

High power space systems which use low dc voltage, high current sources such as thermoelectric generators, will most likely require high voltage conversion for transmission purposes. This study considers the use of the Schwarz resonant converter for use as the basic building block to accomplish this low-to-high voltage conversion for either a dc or an ac spacecraft bus. The Schwarz converter has the important assets of both inherent fault tolerance and resonant operation; parallel operation in modular form is possible. A regulated dc spacecraft bus requires only a single stage converter while a constant frequency ac bus requires a cascaded Schwarz converter configuration. If the power system requires constant output power from the dc generator, then a second converter is required to route unneeded power to a ballast load.

Multi-channel temperature measurement system for automotive battery stack

NASA Astrophysics Data System (ADS)

Lewczuk, Radoslaw; Wojtkowski, Wojciech

2017-08-01

A multi-channel temperature measurement system for monitoring of automotive battery stack is presented in the paper. The presented system is a complete battery temperature measuring system for hybrid / electric vehicles that incorporates multi-channel temperature measurements with digital temperature sensors communicating through 1-Wire buses, individual 1-Wire bus for each sensor for parallel computing (parallel measurements instead of sequential), FPGA device which collects data from sensors and translates it for CAN bus frames. CAN bus is incorporated for communication with car Battery Management System and uses additional CAN bus controller which communicates with FPGA device through SPI bus. The described system can parallel measure up to 12 temperatures but can be easily extended in the future in case of additional needs. The structure of the system as well as particular devices are described in the paper. Selected results of experimental investigations which show proper operation of the system are presented as well.

Distributed control system for parallel-connected DC boost converters

DOEpatents

Goldsmith, Steven

2017-08-15

The disclosed invention is a distributed control system for operating a DC bus fed by disparate DC power sources that service a known or unknown load. The voltage sources vary in v-i characteristics and have time-varying, maximum supply capacities. Each source is connected to the bus via a boost converter, which may have different dynamic characteristics and power transfer capacities, but are controlled through PWM. The invention tracks the time-varying power sources and apportions their power contribution while maintaining the DC bus voltage within the specifications. A central digital controller solves the steady-state system for the optimal duty cycle settings that achieve a desired power supply apportionment scheme for a known or predictable DC load. A distributed networked control system is derived from the central system that utilizes communications among controllers to compute a shared estimate of the unknown time-varying load through shared bus current measurements and bus voltage measurements.

Assessment on the occupational exposure of urban public bus drivers to bioaccessible trace metals through resuspended fraction of settled bus dust.

PubMed

Gao, Peng; Liu, Sa; Ye, Wenyuan; Lin, Nan; Meng, Ping; Feng, Yujie; Zhang, Zhaohan; Cui, Fuyi; Lu, Binyu; Xing, Baoshan

2015-03-01

Limited information is available on the bioaccessible fraction of trace metals in the resuspended fraction of settled bus dust in order to estimate bus drivers' occupational exposure. In this study, 45 resuspended fraction of settled dust samples were collected from gasoline and compressed natural gas (CNG) powered buses and analyzed for trace metals and their fraction concentrations using a three-step sequential extraction procedure. Experimental results showed that zinc (Zn) had the greatest bioaccessible fraction, recorded as an average of 608.53 mg/kg, followed in order of decreasing concentration by 129.80 mg/kg lead (Pb), 56.77 mg/kg copper (Cu), 34.03 mg/kg chromium (Cr), 22.05 mg/kg nickel (Ni), 13.17 mg/kg arsenic (As) and 2.77 mg/kg cadmium (Cd). Among the three settled bus dust exposure pathways, ingestion was the main route. Total exposure hazard index (HIt) for non-carcinogenic effect trace metals was lower than the safety level of 1. The incremental lifetime cancer risk (ILCR) for drivers was estimated for trace metal exposure. Pb and Ni presented relatively high potential risks in the non-carcinogenic and potentially carcinogenic health assessment for all drivers. ILCR was in the range of 1.84E-05 to 7.37E-05 and 1.74E-05 to 6.95E-05 for gasoline and CNG buses, respectively. Copyright © 2014 Elsevier B.V. All rights reserved.

Emission Standards, Public Transit, and Infant Health.

PubMed

Ngo, Nicole S

Transit buses are an integral part of urban life. They reduce externalities generated from private vehicles and increase geographic mobility. However, unlike most private vehicles in the United States, they use diesel fuel and emit higher amounts of toxic pollutants. The U.S. Environmental Protection Agency set emission standards for transit buses starting in 1988 that have been continually updated, but their public health and economic impacts are unclear due to scarce emissions data. I construct a novel panel dataset for the New York City (NYC) Transit bus fleet between 1990 and 2009 and examine the impact of bus pollution on infant health by using bus vintage as a proxy for emissions. I exploit the variation in vintage as older buses are retired and replaced with newer, lower-emitting buses forced to adhere to stricter emission standards. I then assign maternal exposure to bus vintage at the census block level. Findings suggest that maternal exposure to the oldest, unregulated buses is associated with modest reductions in birth weight and gestational age relative to newer buses that abide by emissions policies. I then conduct a back-of-the-envelope cost-benefit calculation and find net economic benefits of $53.3 million resulting from improved emission standards for the 2009 birth cohort in NYC. Since the treatment in this study clearly maps to federal emissions policies, these results are the first to provide credible evidence that transit bus emission standards had a positive effect on infant health.

Minimizing the health and climate impacts of emissions from heavy-duty public transportation bus fleets through operational optimization.

PubMed

Gouge, Brian; Dowlatabadi, Hadi; Ries, Francis J

2013-04-16

In contrast to capital control strategies (i.e., investments in new technology), the potential of operational control strategies (e.g., vehicle scheduling optimization) to reduce the health and climate impacts of the emissions from public transportation bus fleets has not been widely considered. This case study demonstrates that heterogeneity in the emission levels of different bus technologies and the exposure potential of bus routes can be exploited though optimization (e.g., how vehicles are assigned to routes) to minimize these impacts as well as operating costs. The magnitude of the benefits of the optimization depend on the specific transit system and region. Health impacts were found to be particularly sensitive to different vehicle assignments and ranged from worst to best case assignment by more than a factor of 2, suggesting there is significant potential to reduce health impacts. Trade-offs between climate, health, and cost objectives were also found. Transit agencies that do not consider these objectives in an integrated framework and, for example, optimize for costs and/or climate impacts alone, risk inadvertently increasing health impacts by as much as 49%. Cost-benefit analysis was used to evaluate trade-offs between objectives, but large uncertainties make identifying an optimal solution challenging.

Lessons in Financial Literacy Task Design: Authentic, Imaginable, Useful

ERIC Educational Resources Information Center

Sawatzki, Carly

2017-01-01

As part of ongoing design-based research exploring financial literacy teaching and learning, 10 tasks termed "financial dilemmas" were trialled by 14 teachers and more than 300 year 5 and 6 students in four government primary schools in urban Darwin. Drawing on data related to three tasks--"Catching the bus," "Laser…

California Bus Aid Still in Budget Cross Hairs

ERIC Educational Resources Information Center

Fleming, Nora

2012-01-01

California legislators swiftly passed a budget bill last week aimed at sheltering school busing dollars from a midyear budget cut many districts and advocates said particularly hurt rural school systems, along with urban districts with desegregation plans. While the measure, which Gov. Jerry Brown was expected to sign into law, would restore $248…

Research on centrality of urban transport network nodes

NASA Astrophysics Data System (ADS)

Wang, Kui; Fu, Xiufen

2017-05-01

Based on the actual data of urban transport in Guangzhou, 19,150 bus stations in Guangzhou (as of 2014) are selected as nodes. Based on the theory of complex network, the network model of Guangzhou urban transport is constructed. By analyzing the degree centrality index, betweenness centrality index and closeness centrality index of nodes in the network, the level of centrality of each node in the network is studied. From a different point of view to determine the hub node of Guangzhou urban transport network, corresponding to the city's key sites and major transfer sites. The reliability of the network is determined by the stability of some key nodes (transport hub station). The research of network node centralization can provide a theoretical basis for the rational allocation of urban transport network sites and public transport system planning.

Design of belt conveyor electric control device based on CC-link bus

NASA Astrophysics Data System (ADS)

Chen, Goufen; Zhan, Minhua; Li, Jiehua

2016-01-01

In view of problem of the existing coal mine belt conveyor is no field bus communication function, two levels belt conveyor electric control system design is proposed based on field bus. Two-stage belt conveyor electric control system consists of operation platform, PLC control unit, various sensors, alarm device and the water spraying device. The error protection is realized by PLC programming, made use of CC-Link bus technology, the data share and the cooperative control came true between host station and slave station. The real-time monitor was achieved by the touch screen program. Practical application shows that the system can ensure the coalmine production, and improve the automatic level of the coalmine transport equipment.

Diagnostic procedures for Trend Monitoring System (TMS) communications. [coaxial cable bus system

NASA Technical Reports Server (NTRS)

Brown, J. S.; Lenker, M. D.

1979-01-01

A prototype coaxial cable bus communications sytem was developed to support the trend monitoring system (TMS). Troubleshooting procedures are described at the system level. The procedures can be used by repair personnel to isolate a fault in the TMS and to restore the system to operation by swapping out failed components.

77 FR 25529 - Over-the-Road Bus Accessibility Program Grants

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-30

... Century (TEA-21). The OTRB program makes funds available to private operators of over-the-road buses to... bus services. These services are an important element of the U.S. transportation system. TEA-21... delivered after June 8, 1998, the date that the TEA-21 became effective, are eligible for funding under the...

Specification, Measurement, and Control of Electrical Switching Transients

NASA Technical Reports Server (NTRS)

Javor, K.

1999-01-01

There have been several instances of susceptibility to switching transients. The Space Shuttle Spacelab Remote Acquisition Unit (RAU-A standard interface between Spacelab payloads and the Shuttle communications system) will shut down if the input 28 Vdc bus drops below 22 volts for more than 80 gs. Although a MIL-STD-461 derivative CS06 requirement was levied on the RAU, it failed to find this susceptibility. A heavy payload on one aircraft sags the 28 volt bus below 20 volts for milliseconds. Dc-dc converters have an operating voltage. A typical 28 Vdc-to-5 Vdc converter operates within tolerance when input potential is between 17-40 Vdc, A hold-up capacitor can be used to extend the time this range is presented to the convener when the line potential sags or surges outside this range. The designer must know the range of normal transients in order to choose the correct value of hold-up. This report describes the phenomena of electrical power bus transients induced by the switching of loads both on and off the bus, and control thereof.

Access to recreational physical activities by car and bus: an assessment of socio-spatial inequalities in mainland Scotland.

PubMed

Ferguson, Neil S; Lamb, Karen E; Wang, Yang; Ogilvie, David; Ellaway, Anne

2013-01-01

Obesity and other chronic conditions linked with low levels of physical activity (PA) are associated with deprivation. One reason for this could be that it is more difficult for low-income groups to access recreational PA facilities such as swimming pools and sports centres than high-income groups. In this paper, we explore the distribution of access to PA facilities by car and bus across mainland Scotland by income deprivation at datazone level. GIS car and bus networks were created to determine the number of PA facilities accessible within travel times of 10, 20 and 30 minutes. Multilevel negative binomial regression models were then used to investigate the distribution of the number of accessible facilities, adjusting for datazone population size and local authority. Access to PA facilities by car was significantly (p<0.01) higher for the most affluent quintile of area-based income deprivation than for most other quintiles in small towns and all other quintiles in rural areas. Accessibility by bus was significantly lower for the most affluent quintile than for other quintiles in urban areas and small towns, but not in rural areas. Overall, we found that the most disadvantaged groups were those without access to a car and living in the most affluent areas or in rural areas.

Reducing transit bus emissions: Alternative fuels or traffic operations?

NASA Astrophysics Data System (ADS)

Alam, Ahsan; Hatzopoulou, Marianne

2014-06-01

In this study, we simulated the operations and greenhouse gas (GHG) emissions of transit buses along a busy corridor and quantified the effects of two different fuels (conventional diesel and compressed natural gas) as well as a set of driving conditions on emissions. Results indicate that compressed natural gas (CNG) reduces GHG emissions by 8-12% compared to conventional diesel, this reduction could increase to 16% with high levels of traffic congestion. However, the benefits of switching from conventional diesel to CNG are less apparent when the road network is uncongested. We also investigated the effects of bus operations on emissions by applying several strategies such as transit signal priority (TSP), queue jumper lanes, and relocation of bus stops. Results show that in congested conditions, TSP alone can reduce GHG emissions by 14% and when combined with improved technology; a reduction of 23% is achieved. The reduction benefits are even more apparent when other transit operational improvements are combined with TSP. Finally a sensitivity analysis was performed to investigate the effect of operational improvements on emissions under varying levels of network congestion. We observe that under “extreme congestion”, the benefits of TSP decrease.

The Series Connected Buck Boost Regulator Concept for High Efficiency Light Weight DC Voltage Regulation

NASA Technical Reports Server (NTRS)

Birchenough, Arthur G.

2003-01-01

Improvements in the efficiency and size of DC-DC converters have resulted from advances in components, primarily semiconductors, and improved topologies. One topology, which has shown very high potential in limited applications, is the Series Connected Boost Unit (SCBU), wherein a small DC-DC converter output is connected in series with the input bus to provide an output voltage equal to or greater than the input voltage. Since the DC-DC converter switches only a fraction of the power throughput, the overall system efficiency is very high. But this technique is limited to applications where the output is always greater than the input. The Series Connected Buck Boost Regulator (SCBBR) concept extends partial power processing technique used in the SCBU to operation when the desired output voltage is higher or lower than the input voltage, and the implementation described can even operate as a conventional buck converter to operate at very low output to input voltage ratios. This paper describes the operation and performance of an SCBBR configured as a bus voltage regulator providing 50 percent voltage regulation range, bus switching, and overload limiting, operating above 98 percent efficiency. The technique does not provide input-output isolation.

Autonomous Cryogenics Loading Operations Simulation Software: Knowledgebase Autonomous Test Engineer

NASA Technical Reports Server (NTRS)

Wehner, Walter S.

2012-01-01

The Simulation Software, KATE (Knowledgebase Autonomous Test Engineer), is used to demonstrate the automatic identification of faults in a system. The ACLO (Autonomous Cryogenics Loading Operation) project uses KATE to monitor and find faults in the loading of the cryogenics int o a vehicle fuel tank. The KATE software interfaces with the IHM (Integrated Health Management) systems bus to communicate with other systems that are part of ACLO. One system that KATE uses the IHM bus to communicate with is AIS (Advanced Inspection System). KATE will send messages to AIS when there is a detected anomaly. These messages include visual inspection of specific valves, pressure gauges and control messages to have AIS open or close manual valves. My goals include implementing the connection to the IHM bus within KATE and for the AIS project. I will also be working on implementing changes to KATE's Ul and implementing the physics objects in KATE that will model portions of the cryogenics loading operation.

Concentrations of volatile organic compounds, carbon monoxide, carbon dioxide and particulate matter in buses on highways in Taiwan

NASA Astrophysics Data System (ADS)

Hsu, Der-Jen; Huang, Hsiao-Lin

2009-12-01

Although airborne pollutants in urban buses have been studied in many cities globally, long-distance buses running mainly on highways have not been addressed in this regard. This study investigates the levels of volatile organic compounds (VOCs), carbon monoxide (CO), carbon dioxide (CO 2) and particulate matter (PM) in the long-distance buses in Taiwan. Analytical results indicate that pollutants levels in long-distance buses are generally lower than those in urban buses. This finding is attributable to the driving speed and patterns of long-distance buses, as well as the meteorological and geographical features of the highway surroundings. The levels of benzene, toluene, ethylbenzene and xylene (BTEX) found in bus cabins exceed the proposed indoor VOC guidelines for aromatic compounds, and are likely attributable to the interior trim in the cabins. The overall average CO level is 2.3 ppm, with higher average level on local streets (2.9 ppm) than on highways (2.2 ppm). The average CO 2 level is 1493 ppm, which is higher than the guideline for non-industrial occupied settings. The average PM level in this study is lower than those in urban buses and IAQ guidelines set by Taiwan EPA. However, the average PM 10 and PM 2.5 is higher than the level set by WHO. Besides the probable causes mentioned above, fewer passenger movements and less particle re-suspension from bus floor might also cause the lower PM levels. Measurements of particle size distribution reveal that more than 75% of particles are in submicron and smaller sizes. These particles may come from the infiltration from the outdoor air. This study concludes that air exchange rates in long-distance buses should be increased in order to reduce CO 2 levels. Future research on long-distance buses should focus on the emission of VOCs from brand new buses, and the sources of submicron particles in bus cabins.

Digital Autonomous Terminal Access Communication (DATAC) system

NASA Technical Reports Server (NTRS)

Novacki, Stanley M., III

1987-01-01

In order to accommodate the increasing number of computerized subsystems aboard today's more fuel efficient aircraft, the Boeing Co. has developed the DATAC (Digital Autonomous Terminal Access Control) bus to minimize the need for point-to-point wiring to interconnect these various systems, thereby reducing total aircraft weight and maintaining an economical flight configuration. The DATAC bus is essentially a local area network providing interconnections for any of the flight management and control systems aboard the aircraft. The task of developing a Bus Monitor Unit was broken down into four subtasks: (1) providing a hardware interface between the DATAC bus and the Z8000-based microcomputer system to be used as the bus monitor; (2) establishing a communication link between the Z8000 system and a CP/M-based computer system; (3) generation of data reduction and display software to output data to the console device; and (4) development of a DATAC Terminal Simulator to facilitate testing of the hardware and software which transfer data between the DATAC's bus and the operator's console in a near real time environment. These tasks are briefly discussed.

Proton exchange membrane fuel cell system diagnosis based on the signed directed graph method

NASA Astrophysics Data System (ADS)

Hua, Jianfeng; Lu, Languang; Ouyang, Minggao; Li, Jianqiu; Xu, Liangfei

The fuel-cell powered bus is becoming the favored choice for electric vehicles because of its extended driving range, zero emissions, and high energy conversion efficiency when compared with battery-operated electric vehicles. In China, a demonstration program for the fuel cell bus fleet operated at the Beijing Olympics in 2008 and the Shanghai Expo in 2010. It is necessary to develop comprehensive proton exchange membrane fuel cell (PEMFC) diagnostic tools to increase the reliability of these systems. It is especially critical for fuel-cell city buses serving large numbers of passengers using public transportation. This paper presents a diagnostic analysis and implementation study based on the signed directed graph (SDG) method for the fuel-cell system. This diagnostic system was successfully implemented in the fuel-cell bus fleet at the Shanghai Expo in 2010.

A PC-based bus monitor program for use with the transport systems research vehicle RS-232 communication interfaces

NASA Technical Reports Server (NTRS)

Easley, Wesley C.

1991-01-01

Experiment critical use of RS-232 data busses in the Transport Systems Research Vehicle (TSRV) operated by the Advanced Transport Operating Systems Program Office at the NASA Langley Research Center has recently increased. Each application utilizes a number of nonidentical computer and peripheral configurations and requires task specific software development. To aid these development tasks, an IBM PC-based RS-232 bus monitoring system was produced. It can simultaneously monitor two communication ports of a PC or clone, including the nonstandard bus expansion of the TSRV Grid laptop computers. Display occurs in a separate window for each port's input with binary display being selectable. A number of other features including binary log files, screen capture to files, and a full range of communication parameters are provided.

Performance Analysis of Trans-Jakarta Bus Suburban Service Move-Across Greater Jakarta

NASA Astrophysics Data System (ADS)

Tangkudung, ESW; Widyadayinta, C.

2018-03-01

Trans-Jakarta have developed their services scope as Suburban Service or Feeder move-across service that operate from greater Jakarta into Jakarta central vice versa. One of the route is Ciputat – Bundaran Hotel Indonesia (Tosari) and integrated with corridor 1 (one) and 8 (eight). This service is not travel on the exclusive lane or bus-way. Objective of Government Jakarta to provide this service is to decrease private car to enter the central of Jakarta. The objective of this study is to find the performance of the service. Survey have conducted static and dynamic on work day to get variable of travel time and delay, waiting time of passenger at the bus stop, headway and ridership of the bus. Service Standard Minimum of Trans-Jakarta have compared with the result of variable headway, travel speed, and waiting time at bus stop as concern of all the passengers. Analysis use correlation test method and linear regression model have done. The performance of Trans-Jakarta bus suburban service, based on travel speed indicator is fairly bad, only 8.1% of trip could comply with Minimum Service Standard. Bus performance based on the indicator of density in the bus is good, where all points are below the maximum limit i.e. 8 people/m2 at peak hour and 5 people/m2 at off-peak hour.

Task Analysis Assessment on Intrastate Bus Traffic Controllers

NASA Astrophysics Data System (ADS)

Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

2016-11-01

Public transportation acts as social mobility and caters the daily needs of the society for passengers to travel from one place to another. This is true for a country like Malaysia where international trade has been growing significantly over the past few decades. Task analysis assessment was conducted with the consideration of cognitive ergonomic view towards problem related to human factors. Conducting research regarding the task analysis on bus traffic controllers had allowed a better understanding regarding the nature of work and the overall monitoring activities of the bus services. This paper served to study the task analysis assessment on intrastate bus traffic controllers and the objectives of this study include to conduct task analysis assessment on the bus traffic controllers. Task analysis assessment for the bus traffic controllers was developed via Hierarchical Task Analysis (HTA). There are a total of five subsidiary tasks on level one and only two were able to be further broken down in level two. Development of HTA allowed a better understanding regarding the work and this could further ease the evaluation of the tasks conducted by the bus traffic controllers. Thus, human error could be reduced for the safety of all passengers and increase the overall efficiency of the system. Besides, it could assist in improving the operation of the bus traffic controllers by modelling or synthesizing the existing tasks if necessary.

Study on transfer optimization of urban rail transit and conventional public transport

NASA Astrophysics Data System (ADS)

Wang, Jie; Sun, Quan Xin; Mao, Bao Hua

2018-04-01

This paper mainly studies the time optimization of feeder connection between rail transit and conventional bus in a shopping center. In order to achieve the goal of connecting rail transportation effectively and optimizing the convergence between the two transportations, the things had to be done are optimizing the departure intervals, shorting the passenger transfer time and improving the service level of public transit. Based on the goal that has the minimum of total waiting time of passengers and the number of start of classes, establish the optimizing model of bus connecting of departure time. This model has some constrains such as transfer time, load factor, and the convergence of public transportation grid spacing. It solves the problems by using genetic algorithms.

Improving School Bus Safety. Transportation Research Board Special Report 222.

ERIC Educational Resources Information Center

National Academy of Sciences - National Research Council, Washington, DC. Transportation Research Board.

While school buses transport more passengers per trip, the rate of occupant fatalities per mile driven for school buses is one-quarter that for passenger cars. Nevertheless, the public expects school districts and other school bus operators to take all reasonable precautions to protect children as they travel to and from school. Although a variety…

Land use impacts of bus rapid transit : phase II -- effects of BRT station proximity on property values along the Boston silver line Washington Street Corridor.

DOT National Transportation Integrated Search

2012-07-01

The development of Bus Rapid Transit (BRT) systems is relatively recent in the U.S.; however, several systems are operating and many : more are being planned. A comprehensive understanding of the relationship between land uses and BRT systems is need...

2006 Combat Vehicles Conference

DTIC Science & Technology

2006-10-25

stressed or worn out beyond economic repair due to combat operations by repairing, rebuilding, or procuring replacement equipment. These...lives Vehicle Hardening Logistics Solutions for the Warfighter • Unique and economical surge capability • Support in coordination with op tempo...Speed, • Diagnostics Indicators – DECU Health Check Indicator, Utility Bus Comm Failure, 1553 Bus Comm Failure; MPU Critical Failure, Cautions and

A Status report to the Superintendent of Public Instruction on a study of optimal school bus speed limits on Virginia highways.

DOT National Transportation Integrated Search

1988-01-01

The study was prompted by the fact that on Virginia's rural interstate highways there is a three-tiered speed limit: 45 mph for school buses, 55 mph for other buses and trucks, and 65 mph for passenger vehicles. On the urban interstate system, school...

40 CFR 86.004-15 - NOX plus NMHC and particulate averaging, trading, and banking for heavy-duty engines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... all diesel-cycle engine families within the same primary service class is allowed. (ii) Urban buses... averaging set from all other heavy-duty engines. Averaging and trading between diesel cycle bus engine... heavy-duty engines, the equivalent mileage is 6.3 miles. For diesel heavy-duty engines, the equivalent...

40 CFR 86.004-15 - NOX plus NMHC and particulate averaging, trading, and banking for heavy-duty engines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... all diesel-cycle engine families within the same primary service class is allowed. (ii) Urban buses... averaging set from all other heavy-duty engines. Averaging and trading between diesel cycle bus engine... heavy-duty engines, the equivalent mileage is 6.3 miles. For diesel heavy-duty engines, the equivalent...

Insights from a Financial Literacy Task Designer: The Curious Case of Problem Context

ERIC Educational Resources Information Center

Sawatzki, Carly

2016-01-01

As part of ongoing design-based research exploring financial literacy teaching and learning, ten tasks termed "financial dilemmas" were trialled by 14 teachers and more than 300 Year 5 and 6 students in 4 government primary schools in urban Darwin. Drawing on data related to two tasks--"Catching the bus" and "Buying…

American Fuel Cell Bus Project Evaluation. Second Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, Leslie; Post, Matthew

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE'smore » National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.« less

Partial least square method for modelling ergonomic risks factors on express bus accidents in the east coast of peninsular west Malaysia

NASA Astrophysics Data System (ADS)

Hashim, Yusof bin; Taha, Zahari bin

2015-02-01

Public, stake holders and authorities in Malaysian government show great concern towards high numbers of passenger's injuries and passengers fatalities in express bus accident. This paper studies the underlying factors involved in determining ergonomics risk factors towards human error as the reasons in express bus accidents in order to develop an integrated analytical framework. Reliable information about drivers towards bus accident should lead to the design of strategies intended to make the public feel safe in public transport services. In addition there is an analysis of ergonomics risk factors to determine highly ergonomic risk factors which led to accidents. The research was performed in east coast of peninsular Malaysia using variance-based structural equation modeling namely the Partial Least Squares (PLS) regression techniques. A questionnaire survey was carried out at random among 65 express bus drivers operating from the city of Kuantan in Pahang and among 49 express bus drivers operating from the city of Kuala Terengganu in Terengganu to all towns in the east coast of peninsular west Malaysia. The ergonomic risks factors questionnaire is based on demographic information, occupational information, organizational safety climate, ergonomic workplace, physiological factors, stress at workplace, physical fatigue and near miss accidents. The correlation and significant values between latent constructs (near miss accident) were analyzed using SEM SmartPLS, 3M. The finding shows that the correlated ergonomic risks factors (occupational information, t=2.04, stress at workplace, t = 2.81, physiological factor, t=2.08) are significant to physical fatigue and as the mediator to near miss accident at t = 2.14 at p<0.05and T-statistics, t>1.96. The results shows that the effects of physical fatigue due to ergonomic risks factors influence the human error as the reasons in express bus accidents.

Partial least square method for modelling ergonomic risks factors on express bus accidents in the east coast of peninsular west Malaysia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hashim, Yusof bin; Taha, Zahari bin

Public, stake holders and authorities in Malaysian government show great concern towards high numbers of passenger’s injuries and passengers fatalities in express bus accident. This paper studies the underlying factors involved in determining ergonomics risk factors towards human error as the reasons in express bus accidents in order to develop an integrated analytical framework. Reliable information about drivers towards bus accident should lead to the design of strategies intended to make the public feel safe in public transport services. In addition there is an analysis of ergonomics risk factors to determine highly ergonomic risk factors which led to accidents. Themore » research was performed in east coast of peninsular Malaysia using variance-based structural equation modeling namely the Partial Least Squares (PLS) regression techniques. A questionnaire survey was carried out at random among 65 express bus drivers operating from the city of Kuantan in Pahang and among 49 express bus drivers operating from the city of Kuala Terengganu in Terengganu to all towns in the east coast of peninsular west Malaysia. The ergonomic risks factors questionnaire is based on demographic information, occupational information, organizational safety climate, ergonomic workplace, physiological factors, stress at workplace, physical fatigue and near miss accidents. The correlation and significant values between latent constructs (near miss accident) were analyzed using SEM SmartPLS, 3M. The finding shows that the correlated ergonomic risks factors (occupational information, t=2.04, stress at workplace, t = 2.81, physiological factor, t=2.08) are significant to physical fatigue and as the mediator to near miss accident at t = 2.14 at p<0.05and T-statistics, t>1.96. The results shows that the effects of physical fatigue due to ergonomic risks factors influence the human error as the reasons in express bus accidents.« less

26 CFR 48.6421-3 - Time for filing claim for credit or payment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... respect to gasoline used in a qualified business use or as a fuel in an aircraft (other than aircraft in noncommercial aviation) or in § 48.6421-2 with respect to gasoline used either in an intercity or local bus... public or in school bus transportation operations, shall cover only gasoline used during the taxable year...

26 CFR 48.6421-3 - Time for filing claim for credit or payment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... respect to gasoline used in a qualified business use or as a fuel in an aircraft (other than aircraft in noncommercial aviation) or in § 48.6421-2 with respect to gasoline used either in an intercity or local bus... public or in school bus transportation operations, shall cover only gasoline used during the taxable year...

The TOPEX satellite option study

NASA Technical Reports Server (NTRS)

1982-01-01

The applicability of an existing spacecraft bus and subsystems to the requirements of ocean circulation measurements are assessed. The operational meteorological satellite family TIROS and DMSP are recommended. These programs utilize a common bus to satisfy their Earth observation missions. Note that although the instrument complements were different, the pointing accuracies were different, and, initially, the boosters were different, a high degree of commonality was achieved.

49 CFR 37.103 - Purchase or lease of new non-rail vehicles by private entities primarily engaged in the business...

Code of Federal Regulations, 2011 CFR

2011-10-01

... seating capacity of less than eight persons (including the driver), or an over-the-road bus, it shall... individuals who use wheelchairs. (c) Demand responsive systems. If the entity operates a demand responsive... less than eight persons (including the driver), or an over-the-road bus, it shall ensure that the...

Analysis of spacecraft battery charger systems

NASA Astrophysics Data System (ADS)

Kim, Seong J.; Cho, Bo H.

In spacecraft battery charger systems, switching regulators are widely used for bus voltage regulation, charge current regulation, and peak power tracking. Small-signal dynamic characteristics of the battery charging subsystem of direct energy transfer (DET) and peak power tracking (PPT) systems are analyzed to facilitate design of the control loop for optimum performance and stability. Control loop designs of the charger in various modes of operation are discussed. Analyses are verified through simulations. It is shown that when the charger operates in the bus voltage regulation mode, the control-to-voltage transfer function has a negative DC gain and two LHP zeros in both the DET and PPT systems. The control-to-inductor current transfer function also has a negative DC gain and a RHP zero. Thus, in the current-mode control, the current loop can no longer be used to stabilize the system. When the system operates in the charge current regulation mode, the charger operates with a fixed duty cycle which is determined by the regulated bus voltage and the battery voltage. Without an input filter, the converter becomes a first-order system. When the peak power tracker is inactive, the operating point of the solar array output moves to the voltage source region. Thus, the solar array behaves as a stiff voltage source to a constant power load.

Access to Recreational Physical Activities by Car and Bus: An Assessment of Socio-Spatial Inequalities in Mainland Scotland

PubMed Central

Ferguson, Neil S.; Lamb, Karen E.; Wang, Yang; Ogilvie, David; Ellaway, Anne

2013-01-01

Obesity and other chronic conditions linked with low levels of physical activity (PA) are associated with deprivation. One reason for this could be that it is more difficult for low-income groups to access recreational PA facilities such as swimming pools and sports centres than high-income groups. In this paper, we explore the distribution of access to PA facilities by car and bus across mainland Scotland by income deprivation at datazone level. GIS car and bus networks were created to determine the number of PA facilities accessible within travel times of 10, 20 and 30 minutes. Multilevel negative binomial regression models were then used to investigate the distribution of the number of accessible facilities, adjusting for datazone population size and local authority. Access to PA facilities by car was significantly (p<0.01) higher for the most affluent quintile of area-based income deprivation than for most other quintiles in small towns and all other quintiles in rural areas. Accessibility by bus was significantly lower for the most affluent quintile than for other quintiles in urban areas and small towns, but not in rural areas. Overall, we found that the most disadvantaged groups were those without access to a car and living in the most affluent areas or in rural areas. PMID:23409012

Analysis of a dc bus system with a nonlinear constant power load and its delayed feedback control.

PubMed

Konishi, Keiji; Sugitani, Yoshiki; Hara, Naoyuki

2014-02-01

This paper tackles a destabilizing problem of a direct-current (dc) bus system with constant power loads, which can be considered a fundamental problem of dc power grid networks. The present paper clarifies scenarios of the destabilization and applies the well-known delayed-feedback control to the stabilization of the destabilized bus system on the basis of nonlinear science. Further, we propose a systematic procedure for designing the delayed feedback controller. This controller can converge the bus voltage exactly on an unstable operating point without accurate information and can track it using tiny control energy even when a system parameter, such as the power consumption of the load, is slowly varied. These features demonstrate that delayed feedback control can be considered a strong candidate for solving the destabilizing problem.

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children’s exposure

PubMed Central

Hochstetler, Heather A.; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H.; Grinshpun, Sergey A.

2015-01-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m−3. The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors). PMID:25904818

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure

NASA Astrophysics Data System (ADS)

Hochstetler, Heather A.; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H.; Grinshpun, Sergey A.

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 μg m-3. The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure.

PubMed

Hochstetler, Heather A; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H; Grinshpun, Sergey A

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m -3 . The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Department of Homeland Security Assistance to States and Localities: A Summary and Issues for the 111th Congress

DTIC Science & Technology

2009-12-01

6 Intercity Passenger Rail Program (Amtrak) .....................................................................7 Intercity Bus Security Grant...20 Additionally Amtrak is eligible to receive funding to continue security enhancements for its intercity rail services between high-risk urban...Research Service 7 Intercity Passenger Rail Program (Amtrak) The Intercity Passenger Rail Program (IPR) is designed to enhance security of the

Department of Homeland Security Assistance to States and Localities: A Summary and Issues for the 111th Congress

DTIC Science & Technology

2010-04-30

5 Intercity Bus Security Grant Program...eligibility.22 This grant program includes funding for the Freight Rail Security Grant Program (FRSGP), and the Intercity Passenger Rail Program (IPR...eligible to receive funding to continue security enhancements for its intercity rail services between high-risk urban areas. 21 U.S. Department of

HEARING IMPAIRMENT AND HYPERTENSION AMONG LONG DISTANCE BUS DRIVERS

PubMed Central

Abdelmoneim, Ismail

2003-01-01

Objectives: To investigate the prevalence of possible hearing impairment and hypertension in long distance bus drivers compared to the city bus drivers in Abha city. Methods: This was a cross-sectional study involving 62 long distance bus drivers and 46 city bus drivers from October 2001 to March 2002. A specially-designed questionnaire was administered to the drivers to explore some of their socioeconomic backgrounds. A pure tone air conduction audiometry and blood pressure measurements were performed. Results: Long distance bus drivers’ workload is significantly higher than that of city drivers (total weekly hours 64.0±14.3 compared to 46.7±5.5). Hearing impairment was significantly more among long distance drivers in the frequencies of 250, 500, 1000 and 2000 Hz especially in the left ear even after age corrections. The prevalence of mild hearing loss and hypertension were also higher among the long distance drivers (19.4% vs 4.5% and 38.7% vs 13% respectively). Conclusion and recommendations: This study showed more hearing affection and a higher prevalence of hypertension among long distance bus drivers than their counterparts operating in the city. Their hearing acuity should be tested before they start work and regularly afterwards. The stresses and strains of the job should be further studied and relieved; and regular health checks including blood pressure monitoring are to be instituted. PMID:23012034

System level latchup mitigation for single event and transient radiation effects on electronics

DOEpatents

Kimbrough, J.R.; Colella, N.J.

1997-09-30

A ``blink`` technique, analogous to a person blinking at a flash of bright light, is provided for mitigating the effects of single event current latchup and prompt pulse destructive radiation on a micro-electronic circuit. The system includes event detection circuitry, power dump logic circuitry, and energy limiting measures with autonomous recovery. The event detection circuitry includes ionizing radiation pulse detection means for detecting a pulse of ionizing radiation and for providing at an output terminal thereof a detection signal indicative of the detection of a pulse of ionizing radiation. The current sensing circuitry is coupled to the power bus for determining an occurrence of excess current through the power bus caused by ionizing radiation or by ion-induced destructive latchup of a semiconductor device. The power dump circuitry includes power dump logic circuitry having a first input terminal connected to the output terminal of the ionizing radiation pulse detection circuitry and having a second input terminal connected to the output terminal of the current sensing circuitry. The power dump logic circuitry provides an output signal to the input terminal of the circuitry for opening the power bus and the circuitry for shorting the power bus to a ground potential to remove power from the power bus. The energy limiting circuitry with autonomous recovery includes circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential. The circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential includes a series FET and a shunt FET. The invention provides for self-contained sensing for latchup, first removal of power to protect latched components, and autonomous recovery to enable transparent operation of other system elements. 18 figs.

System level latchup mitigation for single event and transient radiation effects on electronics

DOEpatents

Kimbrough, Joseph Robert; Colella, Nicholas John

1997-01-01

A "blink" technique, analogous to a person blinking at a flash of bright light, is provided for mitigating the effects of single event current latchup and prompt pulse destructive radiation on a micro-electronic circuit. The system includes event detection circuitry, power dump logic circuitry, and energy limiting measures with autonomous recovery. The event detection circuitry includes ionizing radiation pulse detection means for detecting a pulse of ionizing radiation and for providing at an output terminal thereof a detection signal indicative of the detection of a pulse of ionizing radiation. The current sensing circuitry is coupled to the power bus for determining an occurrence of excess current through the power bus caused by ionizing radiation or by ion-induced destructive latchup of a semiconductor device. The power dump circuitry includes power dump logic circuitry having a first input terminal connected to the output terminal of the ionizing radiation pulse detection circuitry and having a second input terminal connected to the output terminal of the current sensing circuitry. The power dump logic circuitry provides an output signal to the input terminal of the circuitry for opening the power bus and the circuitry for shorting the power bus to a ground potential to remove power from the power bus. The energy limiting circuitry with autonomous recovery includes circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential. The circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential includes a series FET and a shunt FET. The invention provides for self-contained sensing for latchup, first removal of power to protect latched components, and autonomous recovery to enable transparent operation of other system elements.

Transit Operator Guidelines for Transfer Policy Design

DOT National Transportation Integrated Search

1980-06-01

This report provides guidelines to aid transit operators in the design of policies to accomodate bus and/or rail transfers policy may range from a complete set of operator actions involving vehicle routing and scheduling, transfer charges, passenger ...

How to guide - transit operations decision support systems (TODSS).

DOT National Transportation Integrated Search

2014-12-01

Transit Operations Decision Support Systems (TODSS) are decision support systems designed to support dispatchers in real-time bus operations management in response to incidents, special events, and other changing conditions in order to restore servic...

Power supply circuit for an ion engine sequentially operated power inverters

NASA Technical Reports Server (NTRS)

Cardwell, Jr., Gilbert I. (Inventor)

2000-01-01

A power supply circuit for an ion engine suitable for a spacecraft has a voltage bus having input line and a return line. The power supply circuit includes a pulse width modulation circuit. A plurality of bridge inverter circuits is coupled to the bus and the pulse width modulation circuit. The pulse width modulation circuit generates operating signals having a variable duty cycle. Each bridge inverter has a primary winding and a secondary winding. Each secondary winding is coupled to a rectifier bridge. Each secondary winding is coupled in series with another of the plurality of rectifier bridges.

Increased risk of lung cancer among male professional drivers in urban but not rural areas of Sweden.

PubMed Central

Jakobsson, R; Gustavsson, P; Lundberg, I

1997-01-01

OBJECTIVES: To study the risk of lung cancer in different subgroups of professional drivers in urban and rural areas of Sweden. METHODS: Information on occupation and geographical region was obtained from the Swedish census of 1970 and data on the incidence of lung cancer between 1971 and 1984 from the National Swedish Cancer Registry. Professional drivers were separated into bus, taxi, and long and short distance lorry drivers. Comparisons of cumulative incidence of lung cancer were made between each particular group of drivers and gainfully employed men in the same region. RESULTS: Taxi drivers, and long and short distance lorry drivers in Stockholm County showed increased relative risks (RRs) of lung cancer with the highest risk among the short distance lorry drivers (RR 2.0, 95% confidence interval (95% CI) 1.5 to 2.6). These categories of drivers also showed increased risks in the other two large conurbations in Sweden. In the rest of the country (mainly rural areas) there were no increased RRs for any category of driver. The RR for bus drivers was not increased in any region. After adjustment for assumed differences in smoking habits the RRs remained significantly increased for lorry drivers in Stockholm but not for other groups of drivers in other areas. However, the RRs remained numerically higher in large conurbations than in rural regions for all groups of drivers. CONCLUSIONS: These findings suggest that some factors present in the urban environment play a substantial part in the excess of lung cancer among short distance lorry drivers in urban areas of Sweden. Exposure to motor exhaust fumes may have contributed to this excess. PMID:9155780

Exposure to ultrafine particles and PM 2.5 in four Sydney transport modes

NASA Astrophysics Data System (ADS)

Knibbs, Luke D.; de Dear, Richard J.

2010-08-01

Concentrations of ultrafine (<0.1 μm) particles (UFPs) and PM 2.5 (<2.5 μm) were measured whilst commuting along a similar route by train, bus, ferry and automobile in Sydney, Australia. One trip on each transport mode was undertaken during both morning and evening peak hours throughout a working week, for a total of 40 trips. Analyses comprised one-way ANOVA to compare overall (i.e. all trips combined) geometric mean concentrations of both particle fractions measured across transport modes, and assessment of both the correlation between wind speed and individual trip means of UFPs and PM 2.5, and the correlation between the two particle fractions. Overall geometric mean concentrations of UFPs and PM 2.5 ranged from 2.8 (train) to 8.4 (bus) × 10 4 particles cm -3 and 22.6 (automobile) to 29.6 (bus) μg m -3, respectively, and a statistically significant difference ( p < 0.001) between modes was found for both particle fractions. Individual trip geometric mean concentrations were between 9.7 × 10 3 (train) and 2.2 × 10 5 (bus) particles cm -3 and 9.5 (train) to 78.7 (train) μg m -3. Estimated commuter exposures were variable, and the highest return trip mean PM 2.5 exposure occurred in the ferry mode, whilst the highest UFP exposure occurred during bus trips. The correlation between fractions was generally poor, and in keeping with the duality of particle mass and number emissions in vehicle-dominated urban areas. Wind speed was negatively correlated with, and a generally poor determinant of, UFP and PM 2.5 concentrations, suggesting a more significant role for other factors in determining commuter exposure.

Emergence of criticality in the transportation passenger flow: scaling and renormalization in the Seoul bus system.

PubMed

Goh, Segun; Lee, Keumsook; Choi, Moo Young; Fortin, Jean-Yves

2014-01-01

Social systems have recently attracted much attention, with attempts to understand social behavior with the aid of statistical mechanics applied to complex systems. Collective properties of such systems emerge from couplings between components, for example, individual persons, transportation nodes such as airports or subway stations, and administrative districts. Among various collective properties, criticality is known as a characteristic property of a complex system, which helps the systems to respond flexibly to external perturbations. This work considers the criticality of the urban transportation system entailed in the massive smart card data on the Seoul transportation network. Analyzing the passenger flow on the Seoul bus system during one week, we find explicit power-law correlations in the system, that is, power-law behavior of the strength correlation function of bus stops and verify scale invariance of the strength fluctuations. Such criticality is probed by means of the scaling and renormalization analysis of the modified gravity model applied to the system. Here a group of nearby (bare) bus stops are transformed into a (renormalized) "block stop" and the scaling relations of the network density turn out to be closely related to the fractal dimensions of the system, revealing the underlying structure. Specifically, the resulting renormalized values of the gravity exponent and of the Hill coefficient give a good description of the Seoul bus system: The former measures the characteristic dimensionality of the network whereas the latter reflects the coupling between distinct transportation modes. It is thus demonstrated that such ideas of physics as scaling and renormalization can be applied successfully to social phenomena exemplified by the passenger flow.

Emergence of Criticality in the Transportation Passenger Flow: Scaling and Renormalization in the Seoul Bus System

PubMed Central

Goh, Segun; Lee, Keumsook; Choi, MooYoung; Fortin, Jean-Yves

2014-01-01

Social systems have recently attracted much attention, with attempts to understand social behavior with the aid of statistical mechanics applied to complex systems. Collective properties of such systems emerge from couplings between components, for example, individual persons, transportation nodes such as airports or subway stations, and administrative districts. Among various collective properties, criticality is known as a characteristic property of a complex system, which helps the systems to respond flexibly to external perturbations. This work considers the criticality of the urban transportation system entailed in the massive smart card data on the Seoul transportation network. Analyzing the passenger flow on the Seoul bus system during one week, we find explicit power-law correlations in the system, that is, power-law behavior of the strength correlation function of bus stops and verify scale invariance of the strength fluctuations. Such criticality is probed by means of the scaling and renormalization analysis of the modified gravity model applied to the system. Here a group of nearby (bare) bus stops are transformed into a (renormalized) “block stop” and the scaling relations of the network density turn out to be closely related to the fractal dimensions of the system, revealing the underlying structure. Specifically, the resulting renormalized values of the gravity exponent and of the Hill coefficient give a good description of the Seoul bus system: The former measures the characteristic dimensionality of the network whereas the latter reflects the coupling between distinct transportation modes. It is thus demonstrated that such ideas of physics as scaling and renormalization can be applied successfully to social phenomena exemplified by the passenger flow. PMID:24599221

Application of new electro-optic technology to Space Station Freedom data management system

NASA Technical Reports Server (NTRS)

Husbands, C. R.; Girard, M. M.

1993-01-01

A low risk design methodology to permit the local bus structures to support increased data carrying capacities and to speed messages and data flow between nodes or stations on the Space Station Freedom Data Management System in anticipation of growing requirements was evaluated and recommended. The recommended design employs a collateral fiber optic technique that follows a NATO avionic standard that is developed, tested, and available. Application of this process will permit a potential 25 fold increase in data transfer performance on the local wire bus network with a fiber optic network, maintaining the functionality of the low-speed bus and supporting all of the redundant transmission and fault detection capabilities designed into the existing system. The application of wavelength division multiplexing (WDM) technology to both the local data bus and global data bus segments of the Data Management System to support anticipated additional highspeed data transmission requirements was also examined. Techniques were examined to provide a dual wavelength implementation of the fiber optic collateral networks. This dual wavelength implementation would permit each local bus to support two simultaneous high-speed transfers on the same fiber optic bus structure and operate within the limits of the existing protocol standard. A second WDM study examined the use of spectral sliced technology to provide a fourfold increase in the Fiber Distributed Data Interface (FDDI) global bus networks without requiring modifications to the existing installed cable plant. Computer simulations presented indicated that this data rate improvement can be achieved with commercially available optical components.

Public transportation and tuberculosis transmission in a high incidence setting.

PubMed

Zamudio, Carlos; Krapp, Fiorella; Choi, Howard W; Shah, Lena; Ciampi, Antonio; Gotuzzo, Eduardo; Heymann, Jody; Seas, Carlos; Brewer, Timothy F

2015-01-01

Tuberculosis (TB) transmission may occur with exposure to an infectious contact often in the setting of household environments, but extra-domiciliary transmission also may happen. We evaluated if using buses and/or minibuses as public transportation was associated with acquiring TB in a high incidence urban district in Lima, Peru. Newly diagnosed TB cases with no history of previous treatment and community controls were recruited from August to December 2008 for a case-control study. Crude and adjusted odd ratios (OR) and 95% confidence intervals (CI) were calculated using logistic regression to study the association between bus/minibus use and TB risk. One hundred forty TB cases and 80 controls were included. The overall use of buses/minibuses was 44.9%; 53.3% (72/135) among cases and 30.4% (24/79) among controls [OR: 3.50, (95% CI: 1.60-7.64)]. In the TB group, 25.7% (36/140) of subjects reported having had a recent household TB contact, and 13% (18/139) reported having had a workplace TB contact; corresponding figures for controls were 3.8% (3/80) and 4.1% (3/73), respectively[OR: 8.88 (95% CI: 2.64-29.92), and OR: 3.89 (95% CI: 1.10-13.70)]. In multivariate analyses, age, household income, household contact and using buses/minibuses to commute to work were independently associated with TB [OR for bus/minibus use: 11.8 (95% CI: 1.45-96.07)]. Bus/minibus use to commute to work is associated with TB risk in this high-incidence, urban population in Lima, Peru. Measures should be implemented to prevent TB transmission through this exposure.

An Efficient Method of Sharing Mass Spatio-Temporal Trajectory Data Based on Cloudera Impala for Traffic Distribution Mapping in an Urban City.

PubMed

Zhou, Lianjie; Chen, Nengcheng; Yuan, Sai; Chen, Zeqiang

2016-10-29

The efficient sharing of spatio-temporal trajectory data is important to understand traffic congestion in mass data. However, the data volumes of bus networks in urban cities are growing rapidly, reaching daily volumes of one hundred million datapoints. Accessing and retrieving mass spatio-temporal trajectory data in any field is hard and inefficient due to limited computational capabilities and incomplete data organization mechanisms. Therefore, we propose an optimized and efficient spatio-temporal trajectory data retrieval method based on the Cloudera Impala query engine, called ESTRI, to enhance the efficiency of mass data sharing. As an excellent query tool for mass data, Impala can be applied for mass spatio-temporal trajectory data sharing. In ESTRI we extend the spatio-temporal trajectory data retrieval function of Impala and design a suitable data partitioning method. In our experiments, the Taiyuan BeiDou (BD) bus network is selected, containing 2300 buses with BD positioning sensors, producing 20 million records every day, resulting in two difficulties as described in the Introduction section. In addition, ESTRI and MongoDB are applied in experiments. The experiments show that ESTRI achieves the most efficient data retrieval compared to retrieval using MongoDB for data volumes of fifty million, one hundred million, one hundred and fifty million, and two hundred million. The performance of ESTRI is approximately seven times higher than that of MongoDB. The experiments show that ESTRI is an effective method for retrieving mass spatio-temporal trajectory data. Finally, bus distribution mapping in Taiyuan city is achieved, describing the buses density in different regions at different times throughout the day, which can be applied in future studies of transport, such as traffic scheduling, traffic planning and traffic behavior management in intelligent public transportation systems.

Characterization of elemental and polycyclic aromatic hydrocarbon compositions of urban air in Brisbane

NASA Astrophysics Data System (ADS)

Lim, McKenzie C. H.; Ayoko, Godwin A.; Morawska, Lidia

Characterization of the elemental and polycyclic aromatic hydrocarbons (PAHs) compositions of urban air was undertaken at three major sites in Brisbane, Australia. 17 elements and 16 US EPA priority PAHs were quantified at the sites. The most commonly detected elements in the TSP and PM 2.5 fractions were Al, Cd, Co, Cr, Cu, Fe, Mn, Mo, Si, Sn, Sr and Zn. Compared to the two other sites, PM 2.5 was found to contain higher concentrations of Zr, Mo, V, Al, Mn and Sr at the Queensland University of Technology (QUT) site. In contrast, the Woolloongabba sampling site, which was highly influenced by the vehicular emission and local industrial activities, has higher concentrations of Co, Sn, Cu, Zn and Mg while ANZ site has significantly lower concentration levels of most elements than the other sites; possibly due to the shielding effect of the nearby bush and forest. NAP, PHE, ANT, FLT, PYR and CRY were the most widespread PAHs found in all sites. But only QUT and Woolloongabba bus platform sites had detectable levels of the most carcinogenic US EPA PAH, BAP. The multi-criteria decision making procedures, Preference Ranking Organisation Method for Enrichment Evaluation (PROMETHEE) and Geometrical Analysis for Interactive Aid (GAIA) were used to rank the air samples and to identify the sources of the pollutants. Thus Woolloongabba bus platform was ranked as the most polluted site on the basis of the elemental and PAH compositions of its air samples while Woolloongabba bus platform and QUT sites were ranked as the worst polluted sites in terms of PAHs and PM 2.5 elemental contents, respectively.

Ultrafine PM emissions from natural gas, oxidation-catalyst diesel, and particle-trap diesel heavy-duty transit buses.

PubMed

Holmén, Britt A; Ayala, Alberto

2002-12-01

This paper addresses how current technologies effective for reducing PM emissions of heavy-duty engines may affect the physical characteristics of the particles emitted. Three in-use transit bus configurations were compared in terms of submicron particle size distributions using simultaneous SMPS measurements under two dilution conditions, a minidiluter and the legislated constant volume sampler (CVS). The compressed natural gas (CNG)-fueled and diesel particulate filter (DPF)-equipped diesel configurations are two "green" alternatives to conventional diesel engines. The CNG bus in this study did not have an oxidation catalyst whereas the diesel configurations (with and without particulate filter) employed catalysts. The DPF was a continuously regenerating trap (CRT). Particle size distributions were collected between 6 and 237 nm using 2-minute SMPS scans during idle and 55 mph steady-state cruise operation. Average particle size distributions collected during idle operation of the diesel baseline bus operating on ultralow sulfur fuel showed evidence for nanoparticle growth under CVS dilution conditions relative to the minidiluter. The CRT effectively reduced both accumulation and nuclei mode concentrations by factors of 10-100 except under CVS dilution conditions where nuclei mode concentrations were measured during 55 mph steady-state cruise that exceeded baseline diesel concentrations. The CVS data suggest some variability in trap performance. The CNG bus had accumulation mode concentrations 10-100x lower than the diesel baseline but often displayed large nuclei modes, especially under CVS dilution conditions. Partly this may be explained by the lack of an oxidation catalyst on the CNG, but differences between the minidiluter and CVS size distributions suggest that dilution ratio, temperature-related wall interactions, and differences in tunnel background between the diluters contributed to creating nanoparticle concentrations that sometimes exceeded diesel baseline concentrations when driving under load. The results do not support use of CVS dilution methodology for ultrafine particle sampling, and, despite attention to collection of tunnel blanks in this study, results indicate that a protocol needs to be determined and prescribed for taking into account tunnel blank "emissions" to obtain meaningful comparisons between different technologies. Of critical importance is determining how temperature differences between tunnel blank and test cycle sampling compare in terms of background particle numbers. Total particle number concentrations for the minidiluter sampling point were not significantly different for the two alternative technologies when considering all the steady-cycle data collected. Concentrations ranged from 0.8 to 3 x 10(6) for the baseline bus operating on ultralow sulfur fuel, from 0.5 to 9 x 10(4) for the diesel bus equipped with the CRT filter, and from 1 to 8 x 10(4) particles/cc for the CNG bus.

A design of high-precision BLDCM drive with bus voltage protection

NASA Astrophysics Data System (ADS)

Lian, Xuezheng; Wang, Haitao; Xie, Meilin; Huang, Wei; Li, Dawei; Jing, Feng

2017-11-01

In the application of space satellite turntable, the design of balance wheel is very necessary. To solve the acquisition precision of Brushless DC motor speed is low, and the encoder is also more complex, this paper improves the original hall signal measurement methods. Using the logic device to achieve the six frequency multiplication of hall signal, the signal is used as speed feedback to achieve speed closed-loop control and improve the speed stability. At the same time, in order to prevent the E.M.F of BLDC motor to raise the voltage of the bus bar when reversing or braking, and affect the normal operation of other circuit modules, the analog circuit is used to protect the bus bar voltage by the way of energy consumption braking. The experimental results are consistent with the theoretical design, and the rationality and feasibility of the frequency multiplication scheme and bus voltage protection scheme are verified.

Investigation of short-circuit failure mechanisms of SiC MOSFETs by varying DC bus voltage

NASA Astrophysics Data System (ADS)

Namai, Masaki; An, Junjie; Yano, Hiroshi; Iwamuro, Noriyuki

2018-07-01

In this study, the experimental evaluation and numerical analysis of short-circuit mechanisms of 1200 V SiC planar and trench MOSFETs were conducted at various DC bus voltages from 400 to 800 V. Investigation of the impact of DC bus voltage on short-circuit capability yielded results that are extremely useful for many existing power electronics applications. Three failure mechanisms were identified in this study: thermal runaway, MOS channel current following device turn-off, and rupture of the gate oxide layer (gate oxide layer damage). The SiC MOSFETs experienced lattice temperatures exceeding 1000 K during the short-circuit transient; as Si insulated gate bipolar transistors (IGBTs) are not typically subject to such temperatures, the MOSFETs experienced distinct failure modes, and the mode experienced was significantly influenced by the DC bus voltage. In conclusion, suggestions regarding the SiC MOSFET design and operation methods that would enhance device robustness are proposed.

Development of a Production Ready Automated Wire Delivery System

NASA Technical Reports Server (NTRS)

1997-01-01

The current development effort is a Phase 3 research study entitled "A Production Ready Automated Wire Delivery System", contract number NAS8-39933, awarded to Nichols Research Corporation (NRC). The goals of this research study were to production harden the existing Automated Wire Delivery (AWDS) motion and sensor hardware and test the modified AWDS in a range of welding applications. In addition, the prototype AWDS controller would be moved to the VME bus platform by designing, fabricating and testing a single board VME bus AWDS controller. This effort was to provide an AWDS that could transition from the laboratory environment to production operations. The project was performed in two development steps. Step 1 modified and tested an improved MWG. Step 2 developed and tested the AWDS single board VME bus controller. Step 3 installed the Wire Pilot in a Weld Controller with the imbedded VME bus controller.

Shunt regulation electric power system

NASA Technical Reports Server (NTRS)

Wright, W. H.; Bless, J. J. (Inventor)

1971-01-01

A regulated electric power system having load and return bus lines is described. A plurality of solar cells interconnected in a power supplying relationship and having a power shunt tap point electrically spaced from the bus lines is provided. A power dissipator is connected to the shunt tap point and provides for a controllable dissipation of excess energy supplied by the solar cells. A dissipation driver is coupled to the power dissipator and controls its conductance and dissipation and is also connected to the solar cells in a power taping relationship to derive operating power therefrom. An error signal generator is coupled to the load bus and to a reference signal generator to provide an error output signal which is representative of the difference between the electric parameters existing at the load bus and the reference signal generator. An error amplifier is coupled to the error signal generator and the dissipation driver to provide the driver with controlling signals.

Electrical Design and Evaluation of Asynchronous Serial Bus Communication Network of 48 Sensor Platform LSIs with Single-Ended I/O for Integrated MEMS-LSI Sensors.

PubMed

Shao, Chenzhong; Tanaka, Shuji; Nakayama, Takahiro; Hata, Yoshiyuki; Muroyama, Masanori

2018-01-15

For installing many sensors in a limited space with a limited computing resource, the digitization of the sensor output at the site of sensation has advantages such as a small amount of wiring, low signal interference and high scalability. For this purpose, we have developed a dedicated Complementary Metal-Oxide-Semiconductor (CMOS) Large-Scale Integration (LSI) (referred to as "sensor platform LSI") for bus-networked Micro-Electro-Mechanical-Systems (MEMS)-LSI integrated sensors. In this LSI, collision avoidance, adaptation and event-driven functions are simply implemented to relieve data collision and congestion in asynchronous serial bus communication. In this study, we developed a network system with 48 sensor platform LSIs based on Printed Circuit Board (PCB) in a backbone bus topology with the bus length being 2.4 m. We evaluated the serial communication performance when 48 LSIs operated simultaneously with the adaptation function. The number of data packets received from each LSI was almost identical, and the average sampling frequency of 384 capacitance channels (eight for each LSI) was 73.66 Hz.

Combined comfort model of thermal comfort and air quality on buses in Hong Kong.

PubMed

Shek, Ka Wing; Chan, Wai Tin

2008-01-25

Air-conditioning settings are important factors in controlling the comfort of passengers on buses. The local bus operators control in-bus air quality and thermal environment by conforming to the prescribed levels stated in published standards. As a result, the settings are merely adjusted to fulfill the standards, rather than to satisfy the passengers' thermal comfort and air quality. Such "standard-oriented" practices are not appropriate; the passengers' preferences and satisfaction should be emphasized instead. Thus a "comfort-oriented" philosophy should be implemented to achieve a comfortable in-bus commuting environment. In this study, the achievement of a comfortable in-bus environment was examined with emphasis on thermal comfort and air quality. Both the measurement of physical parameters and subjective questionnaire surveys were conducted to collect practical in-bus thermal and air parameters data, as well as subjective satisfaction and sensation votes from the passengers. By analyzing the correlation between the objective and subjective data, a combined comfort models were developed. The models helped in evaluating the percentage of dissatisfaction under various combinations of passengers' sensation votes towards thermal comfort and air quality. An effective approach integrated the combined comfort model, hardware and software systems and the bus air-conditioning system could effectively control the transient in-bus environment. By processing and analyzing the data from the continuous monitoring system with the combined comfort model, air-conditioning setting adjustment commands could be determined and delivered to the hardware. This system adjusted air-conditioning settings depending on real-time commands along the bus journey. Therefore, a comfortable in-bus air quality and thermal environment could be achieved and efficiently maintained along the bus journey despite dynamic outdoor influences. Moreover, this model can help optimize air-conditioning control by striking a beneficial balance between energy conservation and passengers' satisfaction level.

49 CFR 398.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... passenger automobile or station wagon, any vehicle, locomotive, or car operated exclusively on a rail or rails, or a trolley bus operated by electric power derived from a fixed overhead wire, furnishing local...

49 CFR 398.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... passenger automobile or station wagon, any vehicle, locomotive, or car operated exclusively on a rail or rails, or a trolley bus operated by electric power derived from a fixed overhead wire, furnishing local...

49 CFR 398.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... passenger automobile or station wagon, any vehicle, locomotive, or car operated exclusively on a rail or rails, or a trolley bus operated by electric power derived from a fixed overhead wire, furnishing local...

49 CFR 398.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... passenger automobile or station wagon, any vehicle, locomotive, or car operated exclusively on a rail or rails, or a trolley bus operated by electric power derived from a fixed overhead wire, furnishing local...

The Hughes HS601HP spacecraft power subsystem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krummann, W.; Ayvazian, H.

1998-07-01

The introduction of the Hughes HS 601HP (high power) spacecraft product line continuous the highly successful HS601 three axis stabilized geosynchronus spacecraft with increased power capabilities for larger payload applications. The enhanced power capabilities of the HS 601HP are built upon the heritage of 29 HS601 spacecraft presently in operation. The HS 601HP accommodates payload power ranges of 3 to 7 kilowatts and provides a smooth transition from the lower power HS 601 spacecraft to the HS 702 spacecraft, which has a payload capability up to 13 kilowatts. The HS 601HP spacecraft is designed for a 15 year life withmore » minimal operator interaction. The HS 601HP power subsystem provides a regulated power bus with a voltage range of 52 to 53 volts during all operational phases. The power subsystem is tailored to the specific needs of the spacecraft by selecting standard products from the HS 601HP power catalog. The solar arrays, battery, power control electronics and power distribution electronics are all modular and configurable to the requirements of the spacecraft. The HS 601HP solar array is the primary power source for the spacecraft. The solar array is comprised of two sets of planar solar panels (solar wings) which track the sun in a single spacecraft axis. The solar cells are selected from three different types based upon the spacecraft power generation requirements; silicon, single junction gallium arsenide or dual junction gallium arsenide. The maximum power capability at end of life (15 years, summer solstice) ranges from 4 to 7.7 kilowatts for the three types of solar cells. The HS 601HP battery is the power source for the spacecraft during eclipse and peak sunlight power periods. The battery is comprised of four individual battery packs connected in series to produce a single battery. Each battery pack can accommodate a maximum of eight battery cells with a capacity of 350 ampere-hours. The battery pack also provides for mounting of all electronics utilized by the battery, such as cell bypassing. The power electronics for the HS 601HP spacecraft provide for a tightly regulated power bus whether in sunlight or eclipse (battery discharge) operation. The bus voltage during sunlight is maintained by two bus voltage limiters (BVL), located on the yoke of each solar wing. The BVL maintains the regulated power bus at 52.9 volts by shunting excess solar wing power when not required by the spacecraft. The bus voltage during eclipse is maintained by two battery power controllers (BPC) located on the spacecraft bus shelf. The BPC maintains the regulated power bus at 52.2 volts during battery discharge and also provides for battery charging when excess solar array power is available. The power from the solar array or battery is distributed to the spacecraft by bus and payload power distribution units (PDU). The HS 601HP spacecraft product line now has three spacecraft in orbit. The first was launched in early November of 1997 with the second and third launched in late November and early December of 1997, respectively. The power systems are performing as designed and correlate well with the predicted performance calculations. Several more HS 601HP are scheduled to launch during 1998.« less

School bus’s level of service in Malang City

NASA Astrophysics Data System (ADS)

Hariyani, S.

2017-06-01

School Bus began operated on the 12th of January 2015. Provision of school buses is expected to reduce not only the use of vehicles by students, but it is also to reduce the number of traffic jams. Malang school bus facilities provided by the Department of Transport in cooperation with the Department of Education to serve students in elementary school, junior and senior high schools. After the service running two years, based on the preliminary observation not all students are interested in using the school bus. The research objective was to measure the school bus’s level service. The method to measure school bus’s level of service was used Importance Performance analysis (IPA). The results showed that through IPA, it can be concluded that school bus’s level of service in Malang City have been able to serve students/customers with the mean of degree suitability (Tki) is 111. Meanwhile it must be observed and get more attention to improve by government, attributes which is lies in the first quadrant or concentrate here (attribute Adequate space, Seating capacity, Availability trash can, Passenger facility down in points, The availability of information boards in each bus stop, Availability public telephone in each bus stop, and Availability CCTV in each bus), in order to increase its performance.

Trend Monitoring System (TMS) graphics software

NASA Technical Reports Server (NTRS)

Brown, J. S.

1979-01-01

A prototype bus communications systems, which is being used to support the Trend Monitoring System (TMS) and to evaluate the bus concept is considered. A set of FORTRAN-callable graphics subroutines for the host MODCOMP comuter, and an approach to splitting graphics work between the host and the system's intelligent graphics terminals are described. The graphics software in the MODCOMP and the operating software package written for the graphics terminals are included.

Bidirectional DC-DC conversion device use at system of urban electric transport

NASA Astrophysics Data System (ADS)

Vilberger, M. E.; Vislogusov, D. P.; Kotin, D. A.; Kulekina, A. V.

2017-10-01

The paper considers questions of energy storage devices used in electric transport, especially in the electric traction drive of a trolley bus, in order to provide an autonomous motion, overhead system’s load leveling and energy recovering. For efficiency of the proposed system, a bidirectional DC-DC converter is used. During the simulation, regulation characteristics of the bidirectional DC-DC converters were obtained.

Power converters for the 120 V bus supply control

NASA Astrophysics Data System (ADS)

Elisabelar, Christian

1993-03-01

Power converters for the 120 V bus supply control in such projects as Columbus and Hermes are addressed. Because of the power levels involved and the existing state of the art, several converter modules need to be connected in parallel to supply a single bus. To simplify the study, the power of each converter is set at around 1 kW. Many converter structures which satisfy requirement specifications and several solutions, with or without galvanic insulation, are proposed. The choice and sizing of the converter structure are considered. Stress factors and available technology are selection criteria in determining the most suitable structures. The dimensions of each structure, taking into account the rules of space design enable efficiency to be analytically estimated and it is subsequently verified experimentally. The converter command and its functional performance are then addressed. Numerical simulations with SUCCESS software are run to observe the actual operation of the power part of the converter and to develop the command law with its regulation parameters. The converter is simulated in its entirety and different transients are studied like load variation, no load operating point, short circuit. The response time, stability and behavior under disturbed conditions are thus known. A comparison of the various structures studied enabled the optimal converter to be chosen for some 120 V regulated bus applications.

Study of emergency setting for urban facility using microsimulation tool

NASA Astrophysics Data System (ADS)

Campisi, Tiziana; Canale, Antonino; Tesoriere, Giovanni

2017-11-01

Today Public transport is growing not only in terms of high passenger capacity but also considering high efficiency and it has become one of the preferred alternatives to automobile travel. This is evident, as for example, in the case of airport terminal working and management. The same could be for Bus Transport station considering roadway. As a result, many railway stations experience high levels of pedestrian congestion especially during the morning and afternoon peak periods. Traditional design and evaluation procedures for pedestrian transit facilities aim to maintain a desirable Pedestrian Level-Of-Service (PLOS) for the individual pedestrian areas or sub precincts. More in general, transit facilities and their sub-precincts interact with one another so that pedestrian circulation might be better assessed from a broader systems perspective. Microsimulation packages that can model pedestrians (e.g. VISSIM-VISWALK) can be employed to assess these interactions. This research outlines a procedure for the potential implementation of pedestrian flow analysis in a bus/rail transit station using micro-simulation. Base model data requirements are identified which include static (facility layout and locations of temporary equipment) and dynamic data (pedestrian demand and public transport services). Possible model calibration criteria would be also identified. A VISSIM micro-simulation base model would be developed for one of the main Airport terminal in Sicily (Italy) for investigating proposed station operational and infrastructure changes. This case study provided a good example for the potential implementation of micro-simulation models in the analysis of pedestrian circulation.

Research on Control Strategy of the Micro Grid’s Hybrid Energy System

NASA Astrophysics Data System (ADS)

Gao, Zi-jun; Li, Yang; Wang, Yan-ping; Zong, Ke-yong; Zhang, Jing

2018-03-01

This paper study the structure and operating characteristic of the hybrid energy system which is made of super-capacitor and battery. The system is controlled by strategy of bus voltage following. The bus voltage can change the state from swings to stable quickly when load mutation occurs in the micro grid. The transient impact also can be reduced by this way. The passage set up the model of energy system and make an analysis by the software named MATLAB/Simulink. At last, the passage proves the correctness and the effectiveness of the control strategy and draws a conclusion that the transient impact can be inhibited which occurs in the bus voltage of energy system.

Auxiliary resonant DC tank converter

DOEpatents

Peng, Fang Z.

2000-01-01

An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

The high speed interconnect system architecture and operation

NASA Astrophysics Data System (ADS)

Anderson, Steven C.

The design and operation of a fiber-optic high-speed interconnect system (HSIS) being developed to meet the requirements of future avionics and flight-control hardware with distributed-system architectures are discussed. The HSIS is intended for 100-Mb/s operation of a local-area network with up to 256 stations. It comprises a bus transmission system (passive star couplers and linear media linked by active elements) and network interface units (NIUs). Each NIU is designed to perform the physical, data link, network, and transport functions defined by the ISO OSI Basic Reference Model (1982 and 1983) and incorporates a fiber-optic transceiver, a high-speed protocol based on the SAE AE-9B linear token-passing data bus (1986), and a specialized application interface unit. The operating modes and capabilities of HSIS are described in detail and illustrated with diagrams.

Battery performance of the SKYNET 4A spacecraft during the first six years of on station operation

NASA Technical Reports Server (NTRS)

Johnson, P. J.; Francis, N. R.

1996-01-01

The SKYNET 4A spacecraft is a three-axis stabilized geostationary earth-orbiting military communications satellite which was launched on 1 Jan. 1990 aboard a Titan 3 launch vehicle. The power subsystem is a twin bus, twin battery semi-regulated system and is equipped with one 28-cell, 35 Ampere-hour battery per bus. The cells were manufactured by Gates Aerospace Batteries of Gainesville, FL, and the batteries were built, tested and integrated by British Aerospace Space Systems Ltd. This paper presents a brief survey of the first six years of on-station operation and the operational battery management strategy that has been adopted. Thermal management constraints have led to an unconventional battery operational regime. However, no sign of degradation is evident and the observed spacecraft battery performance remains nominal.

Smart Power Supply for Battery-Powered Systems

NASA Technical Reports Server (NTRS)

Krasowski, Michael J.; Greer, Lawrence; Prokop, Norman F.; Flatico, Joseph M.

2010-01-01

A power supply for battery-powered systems has been designed with an embedded controller that is capable of monitoring and maintaining batteries, charging hardware, while maintaining output power. The power supply is primarily designed for rovers and other remote science and engineering vehicles, but it can be used in any battery alone, or battery and charging source applications. The supply can function autonomously, or can be connected to a host processor through a serial communications link. It can be programmed a priori or on the fly to return current and voltage readings to a host. It has two output power busses: a constant 24-V direct current nominal bus, and a programmable bus for output from approximately 24 up to approximately 50 V. The programmable bus voltage level, and its output power limit, can be changed on the fly as well. The power supply also offers options to reduce the programmable bus to 24 V when the set power limit is reached, limiting output power in the case of a system fault detected in the system. The smart power supply is based on an embedded 8051-type single-chip microcontroller. This choice was made in that a credible progression to flight (radiation hard, high reliability) can be assumed as many 8051 processors or gate arrays capable of accepting 8051-type core presently exist and will continue to do so for some time. To solve the problem of centralized control, this innovation moves an embedded microcontroller to the power supply and assigns it the task of overseeing the operation and charging of the power supply assets. This embedded processor is connected to the application central processor via a serial data link such that the central processor can request updates of various parameters within the supply, such as battery current, bus voltage, remaining power in battery estimations, etc. This supply has a direct connection to the battery bus for common (quiescent) power application. Because components from multiple vendors may have differing power needs, this supply also has a secondary power bus, which can be programmed a priori or on-the-fly to boost the primary battery voltage level from 24 to 50 V to accommodate various loads as they are brought on line. Through voltage and current monitoring, the device can also shield the charging source from overloads, keep it within safe operating modes, and can meter available power to the application and maintain safe operations.

Communications systems and methods for subsea processors

DOEpatents

Gutierrez, Jose; Pereira, Luis

2016-04-26

A subsea processor may be located near the seabed of a drilling site and used to coordinate operations of underwater drilling components. The subsea processor may be enclosed in a single interchangeable unit that fits a receptor on an underwater drilling component, such as a blow-out preventer (BOP). The subsea processor may issue commands to control the BOP and receive measurements from sensors located throughout the BOP. A shared communications bus may interconnect the subsea processor and underwater components and the subsea processor and a surface or onshore network. The shared communications bus may be operated according to a time division multiple access (TDMA) scheme.

Hold-up power supply for flash memory

NASA Technical Reports Server (NTRS)

Ott, William E. (Inventor)

2004-01-01

A hold-up power supply for flash memory systems is provided. The hold-up power supply provides the flash memory with the power needed to temporarily operate when a power loss exists. This allows the flash memory system to complete any erasures and writes, and thus allows it to shut down gracefully. The hold-up power supply detects when a power loss on a power supply bus is occurring and supplies the power needed for the flash memory system to temporally operate. The hold-up power supply stores power in at least one capacitor. During normal operation, power from a high voltage supply bus is used to charge the storage capacitors. When a power supply loss is detected, the power supply bus is disconnected from the flash memory system. A hold-up controller controls the power flow from the storage capacitors to the flash memory system. The hold-up controller uses feedback to assure that the proper voltage is provided from the storage capacitors to the flash memory system. This power supplied by the storage capacitors allows the flash memory system to complete any erasures and writes, and thus allows the flash memory system to shut down gracefully.

Comparison of the application of B-mode and strain elastography ultrasound in the estimation of lymph node metastasis of papillary thyroid carcinoma based on a radiomics approach.

PubMed

Liu, Tongtong; Ge, Xifeng; Yu, Jinhua; Guo, Yi; Wang, Yuanyuan; Wang, Wenping; Cui, Ligang

2018-06-21

B-mode ultrasound (B-US) and strain elastography ultrasound (SE-US) images have a potential to distinguish thyroid tumor with different lymph node (LN) status. The purpose of our study is to investigate whether the application of multi-modality images including B-US and SE-US can improve the discriminability of thyroid tumor with LN metastasis based on a radiomics approach. Ultrasound (US) images including B-US and SE-US images of 75 papillary thyroid carcinoma (PTC) cases were retrospectively collected. A radiomics approach was developed in this study to estimate LNs status of PTC patients. The approach included image segmentation, quantitative feature extraction, feature selection and classification. Three feature sets were extracted from B-US, SE-US, and multi-modality containing B-US and SE-US. They were used to evaluate the contribution of different modalities. A total of 684 radiomics features have been extracted in our study. We used sparse representation coefficient-based feature selection method with 10-bootstrap to reduce the dimension of feature sets. Support vector machine with leave-one-out cross-validation was used to build the model for estimating LN status. Using features extracted from both B-US and SE-US, the radiomics-based model produced an area under the receiver operating characteristic curve (AUC) [Formula: see text] 0.90, accuracy (ACC) [Formula: see text] 0.85, sensitivity (SENS) [Formula: see text] 0.77 and specificity (SPEC) [Formula: see text] 0.88, which was better than using features extracted from B-US or SE-US separately. Multi-modality images provided more information in radiomics study. Combining use of B-US and SE-US could improve the LN metastasis estimation accuracy for PTC patients.

Orbiter multiplexer-demultiplexer (MDM)/Space Lab Bus Interface Unit (SL/BIU) serial data interface evaluation, volume 2

NASA Technical Reports Server (NTRS)

Tobey, G. L.

1978-01-01

Tests were performed to evaluate the operating characteristics of the interface between the Space Lab Bus Interface Unit (SL/BIU) and the Orbiter Multiplexer-Demultiplexer (MDM) serial data input-output (SIO) module. This volume contains the test equipment preparation procedures and a detailed description of the Nova/Input Output Processor Simulator (IOPS) software used during the data transfer tests to determine word error rates (WER).

Wait for the Bus: How Lowcountry School Site Selection and Design Deter Walking to School and Contribute to Urban Sprawl.

ERIC Educational Resources Information Center

Kouri, Christopher

This paper presents a study on how the South Carolina school site selection process can affect the quality of the students' experience and access to their schools. Focusing on students options for getting to school, e.g., hazards that prevent students from walking to school and the size of school sites that place schools on the edge of…

Life Cycle Inventory of Biodiesel and Petroleum Diesel for Use in an Urban Bus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheehan, John; Camobreco, Vince; Duffield, James

1998-05-01

This report presents the findings from a study of the life cycle inventories (LCIs) for petroleum diesel and biodiesel. An LCI is a comprehensive quantification of all the energy and environmental flows associated with a product from “cradle to grave.” It provides information on raw materials extracted from the environment; energy resources consumed; air, water, and solid waste emissions generated.

Physical characterization of fine particulate matter inside the public transit buses fueled by biodiesel in Toledo, Ohio.

PubMed

Shandilya, Kaushik K; Kumar, Ashok

2011-06-15

This study presents the physical characteristics of fine particulate matter (PM) collected inside the urban-public transit buses in Toledo, OH. These buses run on 20% biodiesel blended with ultra-low sulfur diesel (ULSD) (B20). For risk analysis, it is crucial to know the modality of the size distribution and the shape factor of PM collected inside the bus. The number-size distribution, microstructure, and aspect ratio of fine PM filter samples collected in the urban-public transit buses were measured for three years (2007-2009), using an environmental scanning electron microscope (ESEM) coupled with energy dispersive X-ray spectrometry (EDX). Only the reproducible results from repeated experiments on ESEM and size distribution obtained by the GRIMM dust monitor were used in this study. The size distribution was found bi-modal in the winter and fall months and was primarily uni-modal during spring and summer. The aspect ratio for different filter samples collected inside the bus range from 2.4 to 3.6 in average value, with standard deviation ranging from 0.9 to 7.4. The square-shaped and oblong-shaped particles represent the single inhalable particle's morphology characteristics in the air of the Toledo transit buses. Copyright © 2011 Elsevier B.V. All rights reserved.

An explosion of a CNG fuel vessel in an urban bus.

PubMed

Park, Chan-Seong; Jeon, Seung-Won; Moon, Jung-Eun; Lee, Kyu-Jung

2010-03-01

An investigation is presented of the explosion of a CNG (compressed natural gas) fuel vessel, called a liner, in an urban bus. The explosion happened at a gas station 10 min after filling was completed. There were no traces of soot and flames at the failed liner, which would be indicative of explosion by ignition of the gas. The filling process of the station was automatically monitored and recorded in a computer. There was no unusual record of the filling system that indicated excess pressure at the time of the accident. There were cracks on the liner that were initiated at the outer surface of the cylindrical shell located at a point 4 cm above the lower dome where cracks did not originate easily as a result of overload. Chemical analysis was performed on a specimen that was cut from the liner, and there was no peculiarity in the mix. Mechanical analysis was performed on the specimens and showed that the hardness was not in the specified range because of inadequate heat treatment of the metal. The hardness of the liner was strictly controlled in the manufacturing process. All the liners that were manufactured at the same period with the failed liner were recalled for examination.

Thinking about gender, thinking about a common space of observation and discussion of the work activity of the other: the case of bus drivers.

PubMed

Cunha, Liliana; Nogueira, Sónia; Lacomblez, Marianne

2012-01-01

The work activity of urban bus drivers is held in the public space and characterized by a constant vigilance, but the moments of observation the colleagues' work are scarce. This fact results in a paradox--it is a work activity that is more visible to "outsiders" than to "insiders"--which has an important impact on the debate of the work activity from a perspective of gender and the women's work in a predominantly male context. Ergonomic analysis of work and semi-structured interviews were conducted with 32 urban public transport drivers, 16 women and 16 men. The results reveal the lack of conditions for the drivers' knowledge of the activity of another, especially when that other is a woman--while men attribute characteristics to women based on gender stereotypes and an extension of their role in the private sphere, women relate them with the need to prove their competence and be recognized. It is proposed the development, in the context of training, of a space for debate and knowledge of the activity of the other and for the creation of conditions for another integration of women in the profession and for another visibility of their work.

Designing Universitas Indonesia Molina EV Bus Dashboard Using ECQFD and TRIZ

NASA Astrophysics Data System (ADS)

Faiq Pradhila, Muhammad; Suzianti, Amalia; Putri Adinda, Prilly

2018-01-01

Universitas Indonesia is involved in the national electric car development program. One of the focus by the research team is to develop the Molina EV Bus which is planned to replace the current operational bus at UI so that it can be more environmental friendly. With UI developing facilities for the disabled, the Molina research team planned to make a new prototype of the Molina EV Bus to contribute to the facilities developed for the disabled. The new prototype is expected to increase the quality of the previous features of the EV Bus, including the dashboard that had been ignored. To support the development of the new prototype, this research was conducted to design a suitable dashboard for the new prototype. Design of the prototype are made using Autodesk Inventor. This research used the integration of ECQFD (Environmentally Conscious Quality Function Deployment) and TRIZ (Theory of Inventive Problem Solving) method. ECQFD was used to translate user needs into quality characteristics based on environmental aspects. TRIZ was used to translate the quality characteristics into technical specifications. This research has generated 3 sustainable, innovative, and user-preferred dashboard design recommendation for the new prototype.

Electrical Design and Evaluation of Asynchronous Serial Bus Communication Network of 48 Sensor Platform LSIs with Single-Ended I/O for Integrated MEMS-LSI Sensors

PubMed Central

Shao, Chenzhong; Tanaka, Shuji; Nakayama, Takahiro; Hata, Yoshiyuki

2018-01-01

For installing many sensors in a limited space with a limited computing resource, the digitization of the sensor output at the site of sensation has advantages such as a small amount of wiring, low signal interference and high scalability. For this purpose, we have developed a dedicated Complementary Metal-Oxide-Semiconductor (CMOS) Large-Scale Integration (LSI) (referred to as “sensor platform LSI”) for bus-networked Micro-Electro-Mechanical-Systems (MEMS)-LSI integrated sensors. In this LSI, collision avoidance, adaptation and event-driven functions are simply implemented to relieve data collision and congestion in asynchronous serial bus communication. In this study, we developed a network system with 48 sensor platform LSIs based on Printed Circuit Board (PCB) in a backbone bus topology with the bus length being 2.4 m. We evaluated the serial communication performance when 48 LSIs operated simultaneously with the adaptation function. The number of data packets received from each LSI was almost identical, and the average sampling frequency of 384 capacitance channels (eight for each LSI) was 73.66 Hz. PMID:29342923

Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duran, A.; Walkowicz, K.

In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating across the country. Employing a combination of Isaac Instruments GPS/CAN data loggers in conjunction with existing onboard telemetric systems resulted in the capture of operating information for more than 200 individual vehicles in three geographically unique domestic locations. In total, over 1,500 individual operational route shifts from Washington, New York, and Colorado were collected. Upon completing the collection of in-use field data using either NREL-installed data acquisition devices ormore » existing onboard telemetry systems, large-scale duty-cycle statistical analyses were performed to examine underlying vehicle dynamics trends within the data and to explore vehicle operation variations between fleet locations. Based on the results of these analyses, high, low, and average vehicle dynamics requirements were determined, resulting in the selection of representative standard chassis dynamometer test cycles for each condition. In this paper, the methodology and accompanying results of the large-scale duty-cycle statistical analysis are presented, including graphical and tabular representations of a number of relationships between key duty-cycle metrics observed within the larger data set. In addition to presenting the results of this analysis, conclusions are drawn and presented regarding potential applications of advanced vehicle technology as it relates specifically to school buses.« less

Infrastructure and automobile shifts: positioning transit to reduce life-cycle environmental impacts for urban sustainability goals

NASA Astrophysics Data System (ADS)

Chester, Mikhail; Pincetl, Stephanie; Elizabeth, Zoe; Eisenstein, William; Matute, Juan

2013-03-01

Public transportation systems are often part of strategies to reduce urban environmental impacts from passenger transportation, yet comprehensive energy and environmental life-cycle measures, including upfront infrastructure effects and indirect and supply chain processes, are rarely considered. Using the new bus rapid transit and light rail lines in Los Angeles, near-term and long-term life-cycle impact assessments are developed, including consideration of reduced automobile travel. Energy consumption and emissions of greenhouse gases and criteria pollutants are assessed, as well the potential for smog and respiratory impacts. Results show that life-cycle infrastructure, vehicle, and energy production components significantly increase the footprint of each mode (by 48-100% for energy and greenhouse gases, and up to 6200% for environmental impacts), and emerging technologies and renewable electricity standards will significantly reduce impacts. Life-cycle results are identified as either local (in Los Angeles) or remote, and show how the decision to build and operate a transit system in a city produces environmental impacts far outside of geopolitical boundaries. Ensuring shifts of between 20-30% of transit riders from automobiles will result in passenger transportation greenhouse gas reductions for the city, and the larger the shift, the quicker the payback, which should be considered for time-specific environmental goals.

The Command Operations Dashboard: A Common Operating Picture of the Operators

DTIC Science & Technology

2014-06-01

applications in order to collect data: it utilizes Apache Camel as a light-weight enterprise system bus for routing communications through...Mesmer-Magnus & DeChurch, 2009) to focus their limited resources on those teams needing more support. In terms of productivity , new information

Fixed Route Comprehensive Operational Analysis, 1994 Operating Year. Fourth Installment Route 3: Mill Ridge/Mill Plain Analysis

DOT National Transportation Integrated Search

1995-05-01

In October, of 1992, the Housatonic Area Regional Transit (HART) District published a planning study providing an in-depth analysis of its fixed route bus transit service. This comprehensive operational analysis (COA) was the first detailed analysis ...

Fixed Route Comprehensive Operational Analysis, 1994 Operating Year. First Installment, Route 1: Medical Center/Golden Hill Analysis

DOT National Transportation Integrated Search

1994-07-01

In October, of 1992, the Housatonic Area Regional Transit (HART) District published a planning study providing an in-depth analysis of its fixed route bus transit service. This comprehensive operational analysis (COA) was the first detailed analysis ...

Fixed Route Comprehensive Operational Analysis, 1994 Operating Year. Third Installment, Route 6: Lake Avenue/Danbury Fair Mall Analysis

DOT National Transportation Integrated Search

1995-02-01

In October, of 1992, the Housatonic Area Regional Transit (HART) District published a planning study providing an in-depth analysis of its fixed route bus transit service. This comprehensive operational analysis (COA) was the first detailed analysis ...

Deregulation and Intercity Bus Operations in Florida: A Preliminary Study.

DTIC Science & Technology

1981-03-02

revenues have been consistent recently, but expenses have risen. The three areas most frequently served by Rabbit Bus Lines are Disney World, Sea World...Manager, Shoreline Stages had annual revenues of roughly $890,000 in 1980. In terms of trips, about ninety percent of this carrier’s traffic is interstate...this traffic constitutes the bulk of Shoreline Stage’s business by revenue , volume of traffic, and number of passengers. Charter trips to Disney

Infrared Communications for Small Spacecraft: From a Wireless Bus to Cluster Concepts

NASA Technical Reports Server (NTRS)

Webb, Suzanne C.; Schneider, Wolfger; Darrin, M. Ann G.; Boone, Bradley G.; Luers, Philip J.; Day, John H. (Technical Monitor)

2001-01-01

Nanosatellites operating singly or in clusters are anticipated for future space science missions. To implement this new communications paradigm, we are approaching cluster communications by first developing an infrared (IR) intra-craft wireless bus capability, following initially the MIL-STD-1553B protocol. Benefits of an IR wireless bus are low mass, size, power, and cost, simplicity of implementation, ease of use, minimum EMI, and efficient and reliable data transfer. Our goals are to maximize the reliable link margin in order to afford greater flexibility in receiver placement, which will ease technology insertion. We have developed a concept demonstration using a high-speed visible-band silicon PIN photodiode and a high-efficiency visible LED operating at a data rate up to 4 Mb/sec. In designing an internal IR wireless bus, we have characterized various candidate materials, emitters, and geometries, assuming a single reflection. Thus, we have measured the bidirectional reflectance distribution function (BRDF) for five different materials characteristic of typical spacecraft structures, which range from nearly Lambertian to highly specular. We have fit our data to empirical BRDF functions and modeled the detected irradiance anywhere in the plane of incidence for a divergent (LED) emitter. We have also determined the angular limits on the link geometry to remain within the required bit error rate by determining the received signal-to-noise ratio (SNR) for minimum values of irradiance received at the detector.

Characterisation of vibration input to flywheel used on urban bus

NASA Astrophysics Data System (ADS)

Wang, L.; Kanarachos, S.; Christensen, J.

2016-09-01

Vibration induced from road surface has an impact on the durability and reliability of electrical and mechanical components attached on the vehicle. There is little research published relevant to the durability assessment of a flywheel energy recovery system installed on city and district buses. Relevant international standards and legislations were reviewed and large discrepancy was found among them, in addition, there are no standards exclusively developed for kinetic energy recovery systems on vehicles. This paper describes the experimentation of assessment of road surface vibration input to the flywheel on a bus as obtained at the MIRA Proving Ground. Power density spectra have been developed based on the raw data obtained during the experimentation. Validation of this model will be carried out using accelerated life time tests that will be carried out on a shaker rig using an accumulated profile based on the theory of fatigue damage equivalence in time and frequency domain aligned with the model predictions.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction. To date, however, their application to variable speed or servo drives was hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation of frequency and voltage allows independent control of rotor and stator flux, full four quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction to date, however, their application to variable speed or servo drives has been hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation offrequency and voltage allows independent control of rotor and stator flux, full four-quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Data analysis for bus planning and monitoring

DOT National Transportation Integrated Search

2000-01-01

This synthesis report will be of interest to transit agency managers, their schedule and operations planning staffs and others that are responsible for information about systems operations and ridership. It will also be of interest to others who inte...

Fuel Cell Transit Bus Coordination and Evaluation Plan California Fuel Cell Transit Evaluation Team, DRAFT

DOT National Transportation Integrated Search

2003-10-29

The objective of the DOE/NREL evaluation program is to provide comprehensive, unbiased evaluation results of advanced technology vehicle development and operations, evaluation of hydrogen infrastructure development and operation, and descriptions of ...

A Preliminary Review of English Proficiency and Safe Commercial Motor Vehicle Operation.

DOT National Transportation Integrated Search

2008-07-01

Under sponsorship from the U.S. Department of Transportation Federal Motor Carrier Safety Administration, Office of Bus and Truck Standards and Operations, the John A. Volpe National Transportation Systems Center performed a preliminary research stud...

TET-1- A German Microsatellite for Technology On -Orbit Verification

NASA Astrophysics Data System (ADS)

Föckersperger, S.; Lattner, K.; Kaiser, C.; Eckert, S.; Bärwald, W.; Ritzmann, S.; Mühlbauer, P.; Turk, M.; Willemsen, P.

2008-08-01

Due to the high safety standards in the space industry every new product must go through a verification process before qualifying for operation in a space system. Within the verification process the payload undergoes a series of tests which prove that it is in accordance with mission requirements in terms of function, reliability and safety. Important verification components are the qualification for use on the ground as well as the On-Orbit Verification (OOV), i.e. proof that the product is suitable for use under virtual space conditions (on-orbit). Here it is demonstrated that the product functions under conditions which cannot or can only be partially simulated on the ground. The OOV-Program of the DLR serves to bridge the gap between the product tested and qualified on the ground and the utilization of the product in space. Due to regular and short-term availability of flight opportunities industry and research facilities can verify their latest products under space conditions and demonstrate their reliability and marketability. The Technologie-Erprobungs-Tr&äger TET (Technology Experiments Carrier) comprises the core elements of the OOV Program. A programmatic requirement of the OOV Program is that a satellite bus already verified in orbit be used in the first segment of the program. An analysis of suitable satellite buses showed that a realization of the TET satellite bus based on the BIRD satellite bus fulfilled the programmatic requirements best. Kayser-Threde was selected by DLR as Prime Contractor to perform the project together with its major subcontractors Astro- und Feinwerktechnik, Berlin for the platform development and DLR-GSOC for the ground segment development. TET is now designed to be a modular and flexible micro-satellite for any orbit between 450 and 850 km altitude and inclination between 53° and SSO. With an overall mass of 120 kg TET is able to accommodate experiments of up to 50 kg. A multipurpose payload supply systemThere is significant confusion in the space industry today over the terms used to describe satellite bus architectures. Terms such as "standard bus" (or "common bus"), "modular bus" and "plug-and-play bus" are often used with little understanding of what the terms actually mean, and even less understanding of what the differences in these space architectures mean. It may seem that these terms are subtle differentiators, but in reality these terms describe radically different ways to design, build, test, and operate satellites. Furthermore, these terms imply very different business models for the acquisition, operation, and sustainment of space systems. This paper will define and describe the difference between "standard buses", "modular buses" and "plug-and-play buses"; giving examples of each kind with a cost/benefit discussion of each type. under Kayser-Threde responsibility provides the necessary interfaces to the experiments. The first TET mission is scheduled for mid of 2010. TET will be launched as piggy-back payload on any available launcher worldwide to reduce launch cost and provide maximum flexibility. Finally, TET will provide all services required by the experimenters for a one year mission operation to perform a successful OOV-mission with its technology experiments leading to an efficient access to space for German industry and institutions.

Current limiting remote power control module

NASA Technical Reports Server (NTRS)

Hopkins, Douglas C.

1990-01-01

The power source for the Space Station Freedom will be fully utilized nearly all of the time. As such, any loads on the system will need to operate within expected limits. Should any load draw an inordinate amount of power, the bus voltage for the system may sag and disrupt the operation of other loads. To protect the bus and loads some type of power interface between the bus and each load must be provided. This interface is most crucial when load faults occur. A possible system configuration is presented. The proposed interface is the Current Limiting Remote Power Controller (CL-RPC). Such an interface should provide the following power functions: limit overloading and resulting undervoltage; prevent catastrophic failure and still provide for redundancy management within the load; minimize cable heating; and provide accurate current measurement. A functional block diagram of the power processing stage of a CL-RPC is included. There are four functions that drive the circuit design: rate control of current; current sensing; the variable conductance switch (VCS) technology; and the algorithm used for current limiting. Each function is discussed separately.

Design and test of a prototype thermal bus evaporator reservoir aboard the KC-135 0-g aircraft

NASA Technical Reports Server (NTRS)

Brown, Richard F.; Gustafson, Eric; Long, W. Russ

1987-01-01

The Thermal Bus Zero-G Reservoir Demonstration Experiment (RDE) has currently undergone two flights on the NASA-JSC KC-135 Reduced Gravity Aircraft. The objective of the experiment, which uses a smaller version of the evaporator reservoirs being designed for the Prototype Thermal Bus for Space Station, is to demonstrate proper 0-g operation of the reservoir in terms of fluid positioning, draining, and filling. The KC-135 was chosen to provide a cost-effective and timely evaluation of 0-g design issues that would be difficult to predict analytically. A total of fifty 0-g parabolas have been flown, each providing approximately 25-30 seconds of 0-g time. While problems have been encountered, the experiment has provided valuable design data on the 0-g operation of the reservoir. This paper documents the design of the experiment; the results of both flights, based on the high-speed movies taken during the flight and the visual observations of the experimenters; and the design modifications made as a result of the first flight and planned as a result of the second flight.

The universal serial bus endoscope: design and initial clinical experience.

PubMed

Hernandez-Zendejas, Gregorio; Dobke, Marek K; Guerrerosantos, Jose

2004-01-01

Endoscopic forehead lift is a well-established procedure in aesthetic plastic surgery. Many agree that currently available video-endoscopic equipment is bulky, multipieced and sometimes cumbersome in the operating theater. A novel system, the Universal Serial Bus Endoscope (USBE) was designed to simplify and reduce the number of necessary equipment pieces in the endoscopic setup. The USBE is attached by a single cable to a Universal Serial Bus (USB) port of a laptop computer. A built-in miniaturized cold light source provides illumination. A built-in digital camera chip enables procedure recording. The real-time images and movies obtained with USBE are displayed on the computer's screen and recorded on the laptop's hard disk drive. In this study, 25 patients underwent endoscopic browlift using the USBE system to test its clinical usefulness, all with good results and without complications or need for revision. The USBE was found to be reliable and easier to use than current video-endoscope equipment. The operative time needed to complete the procedure by the authors was reduced approximately 50%. The design and main technical characteristics of the USBE are presented.

COMPARISON OF CLEAN DIESEL BUSES TO CNG BUSES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowell, D.; Parsley, W.; Bush,C

2003-08-24

Using previously published data on regulated and unregulated emissions, this paper will compare the environmental performance of current generation transit buses operated on compressed natural gas (CNG) to current generation transit buses operated on ultra low sulfur diesel fuel (ULSD) and incorporating diesel particulate filters (DPF). Unregulated emissions evaluated include toxic compounds associated with adverse health effects (carbonyl, PAH, NPAH, benzene) as well as PM particle count and size distribution. For all regulated and unregulated emissions, both technologies are shown to be comparable. DPF equipped diesel buses and CNG buses have virtually identical levels of PM mass emissions and particlemore » number emissions. DPF-equipped diesel buses have lower HC and CO emissions and lower emissions of toxic substances such as benzene, carbonyls and PAHs than CNG buses. CNG buses have lower NOx emissions than DPF-equipped buses, though CNG bus NOx emissions are shown to be much more variable. In addition, this paper will compare the capital and operating costs of CNG and DPF-equipped buses. The cost comparison is primarily based on the experience of MTA New York City Transit in operating CNG buses since 1995 and DPF-equipped buses fueled with ULSD since 2001. Published data on the experience of other large transit agencies in operating CNG buses is used to validate the NYCT experience. The incremental cost (compared to ''baseline'' diesel) of operating a typical 200-bus depot is shown to be six times higher for CNG buses than for ''clean diesel'' buses. The contributors to this increased cost for CNG buses are almost equally split between increased capital costs for purchase of buses and installation of fueling infrastructure, and increased operating costs for purchase of fuel, bus maintenance, and fuel station maintenance.« less

The school bus routing and scheduling problem with transfers

PubMed Central

Doerner, Karl F.; Parragh, Sophie N.

2015-01-01

In this article, we study the school bus routing and scheduling problem with transfers arising in the field of nonperiodic public transportation systems. It deals with the transportation of pupils from home to their school in the morning taking the possibility that pupils may change buses into account. Allowing transfers has several consequences. On the one hand, it allows more flexibility in the bus network structure and can, therefore, help to reduce operating costs. On the other hand, transfers have an impact on the service level: the perceived service quality is lower due to the existence of transfers; however, at the same time, user ride times may be reduced and, thus, transfers may also have a positive impact on service quality. The main objective is the minimization of the total operating costs. We develop a heuristic solution framework to solve this problem and compare it with two solution concepts that do not consider transfers. The impact of transfers on the service level in terms of time loss (or user ride time) and the number of transfers is analyzed. Our results show that allowing transfers reduces total operating costs significantly while average and maximum user ride times are comparable to solutions without transfers. © 2015 Wiley Periodicals, Inc. NETWORKS, Vol. 65(2), 180–203 2015 PMID:28163329

Getting People to Parks,

DTIC Science & Technology

1976-04-01

2 The area is served by the most extensive transit systems in the world , including subways , surface rail and bus systems, and many miles of...private car. The median trip time of visitors to Jacob Riis Park (Brooklyn) using the subway was three times as long as the time taken by motorists...alternatives are discussed below. Subway Urban mass transit systems are geared to the job of moving large numbers of people to work in the morning and

Application of GPS data for benefits of air quality assessment and fleet management

NASA Astrophysics Data System (ADS)

Hao, Song; Fat Lam, Yun; Cheong Ying, Chi; Chan, Ka Lok

2017-04-01

In the modern digitizedsociety, traffic data can be easily collected for use in roadway development, urban planning and vehicle emission. These data are then further parameterized to support traffic simulation and roadside emission calculations. With the commercialization of AGPS/GPS technology, GPS data are widely utilized to study habit and travelling behaviors. GPS on franchised buses can provide not only positioning information for fleet management but also raw data to analyze traffic situations. In HK, franchised buses account for 6% of RSP and 20% of NOx emissions among the whole vehicle fleet. Being the most heavily means of public transport, the setting up of bus travelling trajectories and service frequency always raise concern from citizens. On this basis, there is an increasing interest and as well as to design and realize an effective cost benefit fleet management strategy. In this study, data collection analysis is carried out on all bus routes (i.e. 112) in Shatin district, one of the 18 districts in Hong Kong. The GPS/AGPS data through Esri ArcGIS investigate the potential benefit of GPS data in different emission scenarios (such as engine type over whole bus fleet). Building on the emission factors from EMFC-HK model, we accounted for factors like travelling distance, idling time, occupancy rate, service frequency, tire and break emissions. Through the simple emission developed model we demonstrate how GPS are data are utilized to assess bus fleet emissions. Further amelioration on the results involve tuning the model with field measurement so as to assess district level emission change after fleet optimization.

MBus: An Ultra-Low Power Interconnect Bus for Next Generation Nanopower Systems

PubMed Central

Pannuto, Pat; Lee, Yoonmyung; Kuo, Ye-Sheng; Foo, ZhiYoong; Kempke, Benjamin; Kim, Gyouho; Dreslinski, Ronald G.; Blaauw, David; Dutta, Prabal

2015-01-01

As we show in this paper, I/O has become the limiting factor in scaling down size and power toward the goal of invisible computing. Achieving this goal will require composing optimized and specialized—yet reusable—components with an interconnect that permits tiny, ultra-low power systems. In contrast to today’s interconnects which are limited by power-hungry pull-ups or high-overhead chip-select lines, our approach provides a superset of common bus features but at lower power, with fixed area and pin count, using fully synthesizable logic, and with surprisingly low protocol overhead. We present MBus, a new 4-pin, 22.6 pJ/bit/chip chip-to-chip interconnect made of two “shoot-through” rings. MBus facilitates ultra-low power system operation by implementing automatic power-gating of each chip in the system, easing the integration of active, inactive, and activating circuits on a single die. In addition, we introduce a new bus primitive: power oblivious communication, which guarantees message reception regardless of the recipient’s power state when a message is sent. This disentangles power management from communication, greatly simplifying the creation of viable, modular, and heterogeneous systems that operate on the order of nanowatts. To evaluate the viability, power, performance, overhead, and scalability of our design, we build both hardware and software implementations of MBus and show its seamless operation across two FPGAs and twelve custom chips from three different semiconductor processes. A three-chip, 2.2 mm3 MBus system draws 8 nW of total system standby power and uses only 22.6 pJ/bit/chip for communication. This is the lowest power for any system bus with MBus’s feature set. PMID:26855555

MBus: An Ultra-Low Power Interconnect Bus for Next Generation Nanopower Systems.

PubMed

Pannuto, Pat; Lee, Yoonmyung; Kuo, Ye-Sheng; Foo, ZhiYoong; Kempke, Benjamin; Kim, Gyouho; Dreslinski, Ronald G; Blaauw, David; Dutta, Prabal

2015-06-01

As we show in this paper, I/O has become the limiting factor in scaling down size and power toward the goal of invisible computing. Achieving this goal will require composing optimized and specialized-yet reusable-components with an interconnect that permits tiny, ultra-low power systems. In contrast to today's interconnects which are limited by power-hungry pull-ups or high-overhead chip-select lines, our approach provides a superset of common bus features but at lower power, with fixed area and pin count, using fully synthesizable logic, and with surprisingly low protocol overhead. We present MBus , a new 4-pin, 22.6 pJ/bit/chip chip-to-chip interconnect made of two "shoot-through" rings. MBus facilitates ultra-low power system operation by implementing automatic power-gating of each chip in the system, easing the integration of active, inactive, and activating circuits on a single die. In addition, we introduce a new bus primitive: power oblivious communication, which guarantees message reception regardless of the recipient's power state when a message is sent. This disentangles power management from communication, greatly simplifying the creation of viable, modular, and heterogeneous systems that operate on the order of nanowatts. To evaluate the viability, power, performance, overhead, and scalability of our design, we build both hardware and software implementations of MBus and show its seamless operation across two FPGAs and twelve custom chips from three different semiconductor processes. A three-chip, 2.2 mm 3 MBus system draws 8 nW of total system standby power and uses only 22.6 pJ/bit/chip for communication. This is the lowest power for any system bus with MBus's feature set.

Comparison of on-road emissions for hybrid and regular transit buses.

PubMed

Hallmark, Shauna L; Wang, Bo; Sperry, Robert

2013-10-01

Hybrid technology offers an attractive option for transit buses, since it has the potential to significantly reduce operating costs for transit agencies. The main impetus behind use of hybrid transit vehicles is fuel savings and reduced emissions. Laboratory tests have indicated that hybrid transit buses can have significantly lower emissions compared with conventional transit buses. However the number of studies is limited and laboratory tests may not represent actual driving conditions, since in-use vehicle operation differs from laboratory test cycles. This paper describes an on-road evaluation of in-use emission differences between hybrid-electric and conventional transit buses for the Ames, Iowa transit authority, CyRide. Emissions were collected on-road using a portable emissions monitoring system (PEMS) for three hybrid and two control buses. Emissions were collected for at least one operating bus day. Each bus was evaluated over the same route pattern, which utilizes the same driver. The number of passengers embarking or disembarking at each stop was collected by an on-board data collector so that passenger load could be included. Vehicle emissions are correlated to engine load demand, which is a function of factors such as vehicle load, speed, and acceleration. PEMS data are provided second by second and vehicle-specific power (VSP) was calculated for each row of data. Instantaneous data were stratified into the defined VSP bins and then average modal emission rates and standard errors were calculated for each bus for each pollutant. Pollutants were then compared by bus type. Carbon dioxide, carbon monoxide, and hydrocarbon emissions were higher for the regular buses across most VSP bins than for the hybrid buses. Nitrogen oxide emissions were unexpectedly higher for the hybrid buses than for the control buses.

Bus operators' responses to job strain: An experimental test of the job demand-control model.

PubMed

Cendales-Ayala, Boris; Useche, Sergio Alejandro; Gómez-Ortiz, Viviola; Bocarejo, Juan Pablo

2017-10-01

The research aim was to test the Job Demand-Control (JDC) Model demands × Control interaction (or buffering) hypothesis in a simulated bus driving experiment. The buffering hypothesis was tested using a 2 (low and high demands) × 2 (low and high decision latitude) design with repeated measures on the second factor. A sample of 80 bus operators were randomly assigned to the low (n = 40) and high demands (n = 40) conditions. Demands were manipulated by increasing or reducing the number of stops to pick up passengers, and decision latitude by imposing or removing restrictions on the Rapid Transit Bus (BRT) operators' pace of work. Outcome variables include physiological markers (heart rate [HR], heart rate variability [HRV], breathing rate [BR], electromyography [EMG], and skin conductance [SC]), objective driving performance and self-report measurements of psychological wellbeing (psychological distress, interest/enjoyment [I/E], perceived competence, effort/importance [E/I], and pressure/tension [P/T]). It was found that job decision latitude moderates the effect of job demands on both physiological arousal (BR: F(1, 74) = 4.680, p = .034, SC: F(1, 75) = 6.769, p = .011, and EMG: F(1, 75) = 6.550, p = .013) and psychological well-being (P/T: F(1, 75) = 4.289, p = .042 and I/E: F(1, 74) = 4.548, p = .036). Consistently with the JDC model buffering hypothesis, the experimental findings suggest that increasing job decision latitude can moderate the negative effect of job demands on different psychophysiological outcomes. This finding is useful for designing organizational and clinical interventions in an occupational group at high risk of work stress-related disease. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Exploiting New Data Sources to Quantify Arterial Congestion and Performance Measures.

DOT National Transportation Integrated Search

2017-01-01

Transit travel time, operating speed and reliability all influence service attractiveness, operating cost and system efficiency. These metrics have a long-term impact on system effectiveness through a change in ridership. As part of its bus dispatch ...

49 CFR 392.62 - Safe operation, buses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Prohibited Practices § 392.62 Safe operation, buses. No person shall drive a bus and a motor...

Electronic scanning pressure measuring system and transducer package

NASA Technical Reports Server (NTRS)

Coe, C. F. (Inventor); Parra, G. T.

1984-01-01

An electronic scanning pressure system that includes a plurality of pressure transducers is examined. A means obtains an electrical signal indicative of a pressure measurement from each of the plurality of pressure transducers. A multiplexing means is connected for selectivity supplying inputs from the plurality of pressure transducers to the signal obtaining means. A data bus connects the plurality of pressure transducers to the multiplexing means. A latch circuit is connected to supply control inputs to the multiplexing means. An address bus is connected to supply an address signal of a selected one of the plurality of pressure transducers to the latch circuit. In operation, each of the pressure transducers is successively scanned by the multiplexing means in response to address signals supplied on the address bus to the latch circuit.

Spatial distribution of diesel transit bus emissions and urban populations: implications of coincidence and scale on exposure.

PubMed

Gouge, Brian; Ries, Francis J; Dowlatabadi, Hadi

2010-09-15

Macroscale emissions modeling approaches have been widely applied in impact assessments of mobile source emissions. However, these approaches poorly characterize the spatial distribution of emissions and have been shown to underestimate emissions of some pollutants. To quantify the implications of these limitations on exposure assessments, CO, NO(X), and HC emissions from diesel transit buses were estimated at 50 m intervals along a bus rapid transit route using a microscale emissions modeling approach. The impacted population around the route was estimated using census, pedestrian count and transit ridership data. Emissions exhibited significant spatial variability. In intervals near major intersections and bus stops, emissions were 1.6-3.0 times higher than average. The coincidence of these emission hot spots and peaks in pedestrian populations resulted in a 20-40% increase in exposure compared to estimates that assumed homogeneous spatial distributions of emissions and/or populations along the route. An additional 19-30% increase in exposure resulted from the underestimate of CO and NO(X) emissions by macroscale modeling approaches. The results of this study indicate that macroscale modeling approaches underestimate exposure due to poor characterization of the influence of vehicle activity on the spatial distribution of emissions and total emissions.

Damage Detection Sensitivity of a Vehicle-based Bridge Health Monitoring System

NASA Astrophysics Data System (ADS)

Miyamoto, Ayaho; Yabe, Akito; Lúcio, Válter J. G.

2017-05-01

As one solution to the problem for condition assessment of existing short and medium span (10-30m) reinforced/prestressed concrete bridges, a new monitoring method using a public bus as part of a public transit system (called “Bus monitoring system”) was proposed, along with safety indices, namely, “characteristic deflection”, which is relatively free from the influence of dynamic disturbances due to such factors as the roughness of the road surface, and a structural anomaly parameter. In this study, to evaluate the practicality of the newly developed bus monitoring system, it has been field-tested over a period of about four years by using an in-service fixed-route bus operating on a bus route in the city of Ube, Yamaguchi Prefecture, Japan. In here, although there are some useful monitoring methods for short and medium span bridges based on the qualitative or quantitative information, the sensitivity of damage detection was newly discussed for safety assessment based on long term health monitoring data. The verification results thus obtained are also described in this paper, and also evaluates the sensitivity of the “characteristic deflection”, which is a bridge (health) condition indicator used by the bus monitoring system, in damage detection. Sensitivity of “characteristic deflection” is verified by introducing artificial damage into a bridge that has ended its service life and is awaiting removal. Furthermore, the sensitivity of “characteristic deflection” is verified by 3D FEM analysis.

Environmental, health, and safety issues of fuel cells in transportation. Volume 1: Phosphoric acid fuel-cell buses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ring, S

1994-12-01

The U.S. Department of Energy (DOE) chartered the Phosphoric Acid Fuel-Cell (PAFC) Bus Program to demonstrate the feasibility of fuel cells in heavy-duty transportation systems. As part of this program, PAFC- powered buses are being built to meet transit industry design and performance standards. Test-bed bus-1 (TBB-1) was designed in 1993 and integrated in March 1994. TBB-2 and TBB-3 are under construction and should be integrated in early 1995. In 1987 Phase I of the program began with the development and testing of two conceptual system designs- liquid- and air-cooled systems. The liquid-cooled PAFC system was chosen to continue, throughmore » a competitive award, into Phase H, beginning in 1991. Three hybrid buses, which combine fuel-cell and battery technologies, were designed during Phase III. After completing Phase II, DOE plans a comprehensive performance testing program (Phase HI) to verify that the buses meet stringent transit industry requirements. The Phase III study will evaluate the PAFC bus and compare it to a conventional diesel bus. This NREL study assesses the environmental, health, and safety (EH&S) issues that may affect the commercialization of the PAFC bus. Because safety is a critical factor for consumer acceptance of new transportation-based technologies the study focuses on these issues. The study examines health and safety together because they are integrally related. In addition, this report briefly discusses two environmental issues that are of concern to the Environmental Protection Agency (EPA). The first issue involves a surge battery used by the PAFC bus that contains hazardous constituents. The second issue concerns the regulated air emissions produced during operation of the PAFC bus.« less

TITLE: Environmental, health, and safety issues offuel cells in transportation. Volume 1: Phosphoricacid fuel-cell buses

NASA Astrophysics Data System (ADS)

Ring, Shan

1994-12-01

The U.S. Department of Energy (DOE) chartered the Phosphoric Acid Fuel-Cell (PAFC) Bus Program to demonstrate the feasibility of fuel cells in heavy-duty transportation systems. As part of this program, PAFC- powered buses are being built to meet transit industry design and performance standards. Test-bed bus-1 (TBB-1) was designed in 1993 and integrated in March 1994. TBB-2 and TBB-3 are under construction and should be integrated in early 1995. In 1987 Phase 1 of the program began with the development and testing of two conceptual system designs- liquid- and air-cooled systems. The liquid-cooled PAFC system was chosen to continue, through a competitive award, into Phase H, beginning in 1991. Three hybrid buses, which combine fuel-cell and battery technologies, were designed during Phase 3. After completing Phase 2, DOE plans a comprehensive performance testing program (Phase H1) to verify that the buses meet stringent transit industry requirements. The Phase 3 study will evaluate the PAFC bus and compare it to a conventional diesel bus. This NREL study assesses the environmental, health, and safety (EH&S) issues that may affect the commercialization of the PAFC bus. Because safety is a critical factor for consumer acceptance of new transportation-based technologies the study focuses on these issues. The study examines health and safety together because they are integrally related. In addition, this report briefly discusses two environmental issues that are of concern to the Environmental Protection Agency (EPA). The first issue involves a surge battery used by the PAFC bus that contains hazardous constituents. The second issue concerns the regulated air emissions produced during operation of the PAFC bus.

Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations.

PubMed

Fleischman, Rafael; Amiel, Ran; Czerwinski, Jan; Mayer, Andreas; Tartakovsky, Leonid

2018-05-01

Retrofitting older vehicles with diesel particulate filter (DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%-1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23-560nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency. Copyright © 2017. Published by Elsevier B.V.

Improvement of multiprocessing performance by using optical centralized shared bus

NASA Astrophysics Data System (ADS)

Han, Xuliang; Chen, Ray T.

2004-06-01

With the ever-increasing need to solve larger and more complex problems, multiprocessing is attracting more and more research efforts. One of the challenges facing the multiprocessor designers is to fulfill in an effective manner the communications among the processes running in parallel on multiple multiprocessors. The conventional electrical backplane bus provides narrow bandwidth as restricted by the physical limitations of electrical interconnects. In the electrical domain, in order to operate at high frequency, the backplane topology has been changed from the simple shared bus to the complicated switched medium. However, the switched medium is an indirect network. It cannot support multicast/broadcast as effectively as the shared bus. Besides the additional latency of going through the intermediate switching nodes, signal routing introduces substantial delay and considerable system complexity. Alternatively, optics has been well known for its interconnect capability. Therefore, it has become imperative to investigate how to improve multiprocessing performance by utilizing optical interconnects. From the implementation standpoint, the existing optical technologies still cannot fulfill the intelligent functions that a switch fabric should provide as effectively as their electronic counterparts. Thus, an innovative optical technology that can provide sufficient bandwidth capacity, while at the same time, retaining the essential merits of the shared bus topology, is highly desirable for the multiprocessing performance improvement. In this paper, the optical centralized shared bus is proposed for use in the multiprocessing systems. This novel optical interconnect architecture not only utilizes the beneficial characteristics of optics, but also retains the desirable properties of the shared bus topology. Meanwhile, from the architecture standpoint, it fits well in the centralized shared-memory multiprocessing scheme. Therefore, a smooth migration with substantial multiprocessing performance improvement is expected. To prove the technical feasibility from the architecture standpoint, a conceptual emulation of the centralized shared-memory multiprocessing scheme is demonstrated on a generic PCI subsystem with an optical centralized shared bus.

Battery capacity and recharging needs for electric buses in city transit service

DOE PAGES

Gao, Zhiming; Lin, Zhenhong; LaClair, Tim J.; ...

2017-01-27

Our paper evaluates the energy consumption and battery performance of city transit electric buses operating on real day-to-day routes and standardized bus drive cycles, based on a developed framework tool that links bus electrification feasibility with real-world vehicle performance, city transit bus service reliability, battery sizing and charging infrastructure. The impacts of battery capacity combined with regular and ultrafast charging over different routes have been analyzed in terms of the ability to maintain city transit bus service reliability like conventional buses. These results show that ultrafast charging via frequent short-time boost charging events, for example at a designated bus stopmore » after completing each circuit of an assigned route, can play a significant role in reducing the battery size and can eliminate the need for longer duration charging events that would cause schedule delays. Furthermore, the analysis presented shows that significant benefits can be realized by employing multiple battery configurations and flexible battery swapping practices in electric buses. These flexible design and use options will allow electric buses to service routes of varying city driving patterns and can therefore enable meaningful reductions to the cost of the vehicle and battery while ensuring service that is as reliable as conventional buses.« less

Battery capacity and recharging needs for electric buses in city transit service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Lin, Zhenhong; LaClair, Tim J.

Our paper evaluates the energy consumption and battery performance of city transit electric buses operating on real day-to-day routes and standardized bus drive cycles, based on a developed framework tool that links bus electrification feasibility with real-world vehicle performance, city transit bus service reliability, battery sizing and charging infrastructure. The impacts of battery capacity combined with regular and ultrafast charging over different routes have been analyzed in terms of the ability to maintain city transit bus service reliability like conventional buses. These results show that ultrafast charging via frequent short-time boost charging events, for example at a designated bus stopmore » after completing each circuit of an assigned route, can play a significant role in reducing the battery size and can eliminate the need for longer duration charging events that would cause schedule delays. Furthermore, the analysis presented shows that significant benefits can be realized by employing multiple battery configurations and flexible battery swapping practices in electric buses. These flexible design and use options will allow electric buses to service routes of varying city driving patterns and can therefore enable meaningful reductions to the cost of the vehicle and battery while ensuring service that is as reliable as conventional buses.« less

Evaluation Of The Advanced Operating System Of The Ann Arbor Transportation Authority : Archives And Records

DOT National Transportation Integrated Search

1999-01-01

This study examines data regularly maintained by the AATA (Ann Arbor Transportation Authority) for evidence of AOS (Advanced Operating System) impact. These data include on-time performance, bus trips broken because of maintenance or other incidents,...

National Fuel Cell Bus Program : Accelerated Testing Report, AC Transit

DOT National Transportation Integrated Search

2009-01-01

This is an evaluation of hydrogen fuel cell transit buses operating at AC Transit in revenue service since March 20, 2006 compared to similar diesel buses operating from the same depot. This evaluation report includes results from November 2007 throu...

An Efficient Method of Sharing Mass Spatio-Temporal Trajectory Data Based on Cloudera Impala for Traffic Distribution Mapping in an Urban City

PubMed Central

Zhou, Lianjie; Chen, Nengcheng; Yuan, Sai; Chen, Zeqiang

2016-01-01

The efficient sharing of spatio-temporal trajectory data is important to understand traffic congestion in mass data. However, the data volumes of bus networks in urban cities are growing rapidly, reaching daily volumes of one hundred million datapoints. Accessing and retrieving mass spatio-temporal trajectory data in any field is hard and inefficient due to limited computational capabilities and incomplete data organization mechanisms. Therefore, we propose an optimized and efficient spatio-temporal trajectory data retrieval method based on the Cloudera Impala query engine, called ESTRI, to enhance the efficiency of mass data sharing. As an excellent query tool for mass data, Impala can be applied for mass spatio-temporal trajectory data sharing. In ESTRI we extend the spatio-temporal trajectory data retrieval function of Impala and design a suitable data partitioning method. In our experiments, the Taiyuan BeiDou (BD) bus network is selected, containing 2300 buses with BD positioning sensors, producing 20 million records every day, resulting in two difficulties as described in the Introduction section. In addition, ESTRI and MongoDB are applied in experiments. The experiments show that ESTRI achieves the most efficient data retrieval compared to retrieval using MongoDB for data volumes of fifty million, one hundred million, one hundred and fifty million, and two hundred million. The performance of ESTRI is approximately seven times higher than that of MongoDB. The experiments show that ESTRI is an effective method for retrieving mass spatio-temporal trajectory data. Finally, bus distribution mapping in Taiyuan city is achieved, describing the buses density in different regions at different times throughout the day, which can be applied in future studies of transport, such as traffic scheduling, traffic planning and traffic behavior management in intelligent public transportation systems. PMID:27801869

Spacecraft (Mobile Satellite) configuration design study

NASA Technical Reports Server (NTRS)

1985-01-01

The relative costs to procure and operate a two-satellite mobile satellite system designed to operate either in the UHF band of the L Band, and with several antenna diameter options in each frequency band was investigated. As configured, the size of the spacecraft is limited to the current RCA Series 4000 Geosynchronous Communications Spacecraft bus, which spans the range from 4000 to 5800 pounds in the transfer orbit. The Series 4000 bus forms the basis around which the Mobile Satellite transponder and associated antennas were appended. Although the resultant configuration has little outward resemblance to the present Series 4000 microwave communications spacecraft, the structure, attitude control, thermal, power, and command and control subsystems of the Series 4000 spacecraft are all adapted to support the Mobile Satellite mission.

HyspIRI Intelligent Payload Module(IPM) and Benchmarking Algorithms for Upload

NASA Technical Reports Server (NTRS)

Mandl, Daniel

2010-01-01

Features: Hardware: a) Xilinx Virtex-5 (GSFC Space Cube 2); b) 2 x 400MHz PPC; c) 100MHz Bus; d) 2 x 512MB SDRAM; e) Dual Gigabit Ethernet. Support Linux kernel 2.6.31 (gcc version 4.2.2). Support software running in stand alone mode for better performance. Can stream raw data up to 800 Mbps. Ready for operations. Software Application Examples: Band-stripping Algiotrhmsl:cloud, sulfur, flood, thermal, SWIL, NDVI, NDWI, SIWI, oil spills, algae blooms, etc. Corrections: geometric, radiometric, atmospheric. Core Flight System/dynamic software bus. CCSDS File Delivery Protocol. Delay Tolerant Network. CASPER /onboard planning. Fault monitoring/recovery software. S/C command and telemetry software. Data compression. Sensor Web for Autonomous Mission Operations.

The 30-cm ion thruster power processor

NASA Technical Reports Server (NTRS)

Herron, B. G.; Hopper, D. J.

1978-01-01

A power processor unit for powering and controlling the 30 cm Mercury Electron-Bombardment Ion Thruster was designed, fabricated, and tested. The unit uses a unique and highly efficient transistor bridge inverter power stage in its implementation. The system operated from a 200 to 400 V dc input power bus, provides 12 independently controllable and closely regulated dc power outputs, and has an overall power conditioning capacity of 3.5 kW. Protective circuitry was incorporated as an integral part of the design to assure failure-free operation during transient and steady-state load faults. The implemented unit demonstrated an electrical efficiency between 91.5 and 91.9 at its nominal rated load over the 200 to 400 V dc input bus range.

Homicides, Public Goods, and Population Health in the Context of High Urban Violence Rates in Cali, Colombia.

PubMed

Martínez, Lina; Prada, Sergio; Estrada, Daniela

2018-06-01

Obesity and frequent mental and physical distress are often associated with major health problems. The characteristics of the urban environment, such as homicide rates and public goods provision, play an important role in influencing participation in physical activity and in overall mental health. This study aimed to determine whether there was a relationship between homicide rates and public goods provision on the health outcomes of the citizens of Cali, Colombia, a city known for its high urban violence rate and low municipal investment in public goods. We used a linear probability model to relate homicide rates and public goods provision (lighted parks, effective public space per inhabitant, and bus stations) at the district level to health outcomes (obesity and frequent mental and physical distress). Individual data were obtained from the 2014 CaliBRANDO survey, and urban context characteristics were obtained from official government statistics. After controlling for individual covariates, results showed that homicide rates were a risk factor in all examined outcomes. An increase in 1.0 m 2 of public space per inhabitant reduced the probability of an individual being obese or overweight by 0.2% (95% confidence interval (CI) = - 0.004 to - 0.001) and the probability of frequent physical distress by 0.1% (95% CI = - 0.002 to - 0.001). On average, the presence of one additional bus station increased the probability of being obese or overweight by 1.1%, the probability of frequent mental distress by 0.3% (95% CI = 0.001-0.004), and the probability of frequent physical distress by 0.02% (95% CI = 0.000-0.003). Living in districts with adequate public space and lighted parks lowers the probability of being obese and high homicide rates, which are correlated with poor health outcomes in Cali, Colombia. Investments in public goods provision and urban safety to reduce obesity rates may contribute to a better quality of life for the population.

A Versatile Image Processor For Digital Diagnostic Imaging And Its Application In Computed Radiography

NASA Astrophysics Data System (ADS)

Blume, H.; Alexandru, R.; Applegate, R.; Giordano, T.; Kamiya, K.; Kresina, R.

1986-06-01

In a digital diagnostic imaging department, the majority of operations for handling and processing of images can be grouped into a small set of basic operations, such as image data buffering and storage, image processing and analysis, image display, image data transmission and image data compression. These operations occur in almost all nodes of the diagnostic imaging communications network of the department. An image processor architecture was developed in which each of these functions has been mapped into hardware and software modules. The modular approach has advantages in terms of economics, service, expandability and upgradeability. The architectural design is based on the principles of hierarchical functionality, distributed and parallel processing and aims at real time response. Parallel processing and real time response is facilitated in part by a dual bus system: a VME control bus and a high speed image data bus, consisting of 8 independent parallel 16-bit busses, capable of handling combined up to 144 MBytes/sec. The presented image processor is versatile enough to meet the video rate processing needs of digital subtraction angiography, the large pixel matrix processing requirements of static projection radiography, or the broad range of manipulation and display needs of a multi-modality diagnostic work station. Several hardware modules are described in detail. For illustrating the capabilities of the image processor, processed 2000 x 2000 pixel computed radiographs are shown and estimated computation times for executing the processing opera-tions are presented.

Commuter exposure to ultrafine particles in different urban locations, transportation modes and routes

NASA Astrophysics Data System (ADS)

Ragettli, Martina S.; Corradi, Elisabetta; Braun-Fahrländer, Charlotte; Schindler, Christian; de Nazelle, Audrey; Jerrett, Michael; Ducret-Stich, Regina E.; Künzli, Nino; Phuleria, Harish C.

2013-10-01

A better understanding of ultrafine particle (UFP) exposure in different urban transport microenvironments is important for epidemiological exposure assessments and for policy making. Three sub-studies were performed to characterize personal exposure to UFP concentration and average particle size distribution diameters in frequently traveled commuter microenvironments in the city of Basel, Switzerland. First, the spatial variation of sidewalk UFP exposures within urban areas and transport-specific microenvironments was explored. Second, exposure to UFP concentration and average particle size were quantified for five modes of transportation (walking, bicycle, bus, tram, car) during different times of the day and week, along the same route. Finally, the contribution of bicycle commuting along two different routes (along main roads, away from main roads) to total daily exposures was assessed by 24-h personal measurements. In general, smaller average particle sizes and higher UFP levels were measured at places and for travel modes in close proximity to traffic. Average trip UFP concentrations were higher in car (31,784 particles cm-³) and on bicycle (22,660 particles cm-³) compared to walking (19,481 particles cm-³) and public transportation (14,055-18,818 particles cm-³). Concentrations were highest for all travel modes during weekday morning rush hours, compared to other time periods. UFP concentration was lowest in bus, regardless of time period. Bicycle travel along main streets between home and work place (24 min on average) contributed 21% and 5% to total daily UFP exposure in winter and summer, respectively. Contribution of bicycle commutes to total daily UFP exposure could be reduced by half if main roads are avoided. Our results show the importance of considering commuter behavior and route choice in exposure assessment studies.

Building Public Confidence in Urban Schools: It Begins inside the District. A Guide for Administrators and Board Members. A Public Relations Executives Network Project of the Council of the Great City Schools, 2009-2010

ERIC Educational Resources Information Center

Council of the Great City Schools, 2010

2010-01-01

Effective organizational communication begins with employees, who should be communications ambassadors for a district. From administrators to teachers to school bus drivers to custodians, employees set the tone for a district. The informal conversations they have at church, the bowling alley, the barbershop and other venues can make or break the…

[Particle emission characteristics of diesel bus fueled with bio-diesel].

PubMed

Lou, Di-Ming; Chen, Feng; Hu, Zhi-Yuan; Tan, Pi-Qiang; Hu, Wei

2013-10-01

With the use of the Engine Exhaust Particle Sizer (EEPS), a study on the characteristics of particle emissions was carried out on a China-IV diesel bus fueled with blends of 5% , 10% , 20% , 50% bio-diesel transformed from restaurant waste oil and China-IV diesel (marked separately by BD5, BD10, BD20, BD50), pure bio-diesel (BD100) and pure diesel (BD0). The results indicated that particulate number (PN) and mass (PM) emissions of bio-diesel blends increased with the increase in bus speed and acceleration; with increasing bio-diesel content, particulate emissions displayed a relevant declining trend. In different speed ranges, the size distribution of particulate number emissions (PNSD) was bimodal; in different acceleration ranges, PNSD showed a gradual transition from bimodal shape to unimodal when bus operation was switched from decelerating to accelerating status. Bio-diesel blends with higher mixture ratios showed significant reduction in PN emissions for accumulated modes, and the particulate number emission peaks moved towards smaller sizes; but little change was obtained in PN emissions for nuclei modes; reduction also occurred in particle geometric diameter (Dg).

The fiber-optic high-speed data bus for a new generation of military aircraft

NASA Astrophysics Data System (ADS)

Uhlhorn, Roger W.

1991-02-01

The avionic suite for the next generation of military aircraft is being designed with component and module commonality in mind in order to control recurring costs and capitalize on economy of scale. The backbone of the suite fashioned out of these modular building blocks is the fiber-optic bit-serial time-division multiplexed high-speed data bus (HSDB), operating at 50 Mb/s, which provides command and control communications among most of the aircraft subsystems and can be used to provide communications for a fly-by-light flight-control system or for the block transfer of data between mass memories and data processors. The fiber-optic HSDB is examined from the top down, beginning with an overview of the evolution of avionic architectures. A review is given of the standardization activity associated with development of the network, the protocols chosen to implement the desired communication functions, configuration options, and the fiber-optic components used in the bus interfaces or other active nodes of the network. It is believed that the utility of the bus extends beyond aircraft to spacecraft, ships, and land vehicles.

Informing Urban Decision Making with an Array of Things

NASA Astrophysics Data System (ADS)

Jacob, R. L.; Catlett, C.; Beckman, P. H.; Sankaran, R.

2015-12-01

Over the next several decades, the population of the world's cities is projected to nearly double, increasing by 2.6 billion people and requiring massive urban expansion globally. This massive growth in urban density and scale will compound ongoing city challenges related to climate change, energy, infrastructure, public health, and more. Cities are using data they already collect such as 311 calls, bus and train operations, street repair orders, census data and building permits to help understand the complex interactions between the human, built and natural systems within a city and inform their decision making. Helping to guide urban decision-making is The Array of Things (AoT): a new tool for measuring many aspects of the physical environment of urban areas at the city block scale with continuous, reliable, integrated data from a variety of sensors. An AoT node includes multiple sensors to measure basic meteorological quantities such as pressure, temperature and humidity as well as light and trace gases such as carbon monoxide, nitrogen dioxide, sulfur dioxide and ozone. The sensors operate 24/7 with ingest frequencies as high as 1Hz. The nodes are modular and allow new sensors to be added or swapped out. The hardware/software backbone of an AoT node is provided by the Waggle architecture. Each AoT node includes, via Waggle, compute power from a single board computer running Linux that allows data to be processed in-situ and, if needed, command and control of components of the node. Data is communicated in near real-time typically through WiFi, 3G or wired ethernet to a designated host and resilience is built-in to prevent data loss if communication is disrupted. The AoT includes a software stack with a programmable API and cloud-based infrastructure for performing data ingest and further analysis. The first full instance of AoT will comprise 500 nodes deployed in the City of Chicago, each with power, Internet, and a base set of sensing and embedded information systems capabilities. A prototype of the Array of Things consisting of 12 nodes has been deployed on the campus of the University of Chicago and initial data from the array will be presented.

49 CFR 37.73 - Purchase or lease of used non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... public entities operating fixed route systems. 37.73 Section 37.73 Transportation Office of the Secretary... operating fixed route systems. (a) Except as provided elsewhere in this section, each public entity operating a fixed route system purchasing or leasing, after August 25, 1990, a used bus or other used...

49 CFR 37.73 - Purchase or lease of used non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... public entities operating fixed route systems. 37.73 Section 37.73 Transportation Office of the Secretary... operating fixed route systems. (a) Except as provided elsewhere in this section, each public entity operating a fixed route system purchasing or leasing, after August 25, 1990, a used bus or other used...

49 CFR 37.73 - Purchase or lease of used non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... public entities operating fixed route systems. 37.73 Section 37.73 Transportation Office of the Secretary... operating fixed route systems. (a) Except as provided elsewhere in this section, each public entity operating a fixed route system purchasing or leasing, after August 25, 1990, a used bus or other used...

49 CFR 37.73 - Purchase or lease of used non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... public entities operating fixed route systems. 37.73 Section 37.73 Transportation Office of the Secretary... operating fixed route systems. (a) Except as provided elsewhere in this section, each public entity operating a fixed route system purchasing or leasing, after August 25, 1990, a used bus or other used...

49 CFR 37.73 - Purchase or lease of used non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... public entities operating fixed route systems. 37.73 Section 37.73 Transportation Office of the Secretary... operating fixed route systems. (a) Except as provided elsewhere in this section, each public entity operating a fixed route system purchasing or leasing, after August 25, 1990, a used bus or other used...

Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles.

PubMed

Kado, Norman Y; Okamoto, Robert A; Kuzmicky, Paul A; Kobayashi, Reiko; Ayala, Alberto; Gebel, Michael E; Rieger, Paul L; Maddox, Christine; Zafonte, Leo

2005-10-01

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation catalyst) and from a vehicle fueled with low-sulfur diesel fuel (equipped with DPF) were lower than from the low-sulfur diesel fueled vehicle equipped with OC. All vehicle configurations had generally lower emissions of toxics than an uncontrolled diesel engine. Tunnel backgrounds (measurements without the vehicle running) were measured throughout this study and were helpful in determining the incremental increase in pollutant emissions. Also, the on-site determination of VOCs, especially 1,3-butadiene, helped minimize measurement losses due to sample degradation after collection.

7 CFR 271.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... alone, or in conjunction with another access device, to obtain payments, allotments, benefits, money... retail food business operated from a truck, bus, pushcart, or other mobile vehicle. Identification (ID...

7 CFR 271.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... alone, or in conjunction with another access device, to obtain payments, allotments, benefits, money... retail food business operated from a truck, bus, pushcart, or other mobile vehicle. Identification (ID...

7 CFR 271.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... alone, or in conjunction with another access device, to obtain payments, allotments, benefits, money... retail food business operated from a truck, bus, pushcart, or other mobile vehicle. Identification (ID...

The impact of urbanization on the community food environment in China.

PubMed

Wu, Yang; Xue, Hong; Wang, Huijun; Su, Chang; Du, Shufa; Wang, Youfa

2017-05-01

Research on how urbanization has influenced the food environment in China is limited. The study aimed to examine the impact of urbanization on the food environment in China. Longitudinal data collected during 1989-2009 from the China Health and Nutrition Survey were used, which covered 9 provinces in China. Urbanicity index (0-10) was assessed using an urbanicity scale. Final analyses included 216 communities. Random-effect models were used in analyses. Urbanization (higher urbanicity index) increased the odds of having fast food restaurants (OR=2.78, 95% CI: 2.18-3.54) and other indoor restaurants (OR=2.93, 95% CI: 2.28-3.76) within the community, the odds of having supermarkets (OR=2.43, 95% CI: 2.04-2.89) and free markets (OR=2.56, 95% CI: 1.77-3.70) within 30 minutes' bus ride from the community. Food prices for apples (β=0.06, 95% CI: 0.04-0.08) and lean pork (β =0.02, 95% CI: 0.01-0.03) increased with urbanicity, while prices for other food did not. Urbanicity was positively associated with community norms for fast food consumption (RR=1.28, 95% CI: 1.22-1.33), fast food preferences (RR=1.09, 95% CI: 1.06-1.12) and nutrition knowledge (RR=1.02, 95% CI: 1.01-1.03). Urbanization is associated with food environment in China. The findings provide insight for future economic development and public health efforts related to urbanization.

DC Bus Regulation with a Flywheel Energy Storage System

NASA Technical Reports Server (NTRS)

Kenny, Barbara H.; Kascak, Peter E.

2003-01-01

This paper describes the DC bus regulation control algorithm for the NASA flywheel energy storage system during charge, charge reduction and discharge modes of operation. The algorithm was experimentally verified with results given in a previous paper. This paper presents the necessary models for simulation with detailed block diagrams of the controller algorithm. It is shown that the flywheel system and the controller can be modeled in three levels of detail depending on the type of analysis required. The three models are explained and then compared using simulation results.

DG Planning with Amalgamation of Operational and Reliability Considerations

NASA Astrophysics Data System (ADS)

Battu, Neelakanteshwar Rao; Abhyankar, A. R.; Senroy, Nilanjan

2016-04-01

Distributed Generation has been playing a vital role in dealing issues related to distribution systems. This paper presents an approach which provides policy maker with a set of solutions for DG placement to optimize reliability and real power loss of the system. Optimal location of a Distributed Generator is evaluated based on performance indices derived for reliability index and real power loss. The proposed approach is applied on a 15-bus radial distribution system and a 18-bus radial distribution system with conventional and wind distributed generators individually.

Increasing the Automation and Autonomy for Spacecraft Operations with Criteria Action Table

NASA Technical Reports Server (NTRS)

Li, Zhen-Ping; Savki, Cetin

2005-01-01

The Criteria Action Table (CAT) is an automation tool developed for monitoring real time system messages for specific events and processes in order to take user defined actions based on a set of user-defined rules. CAT was developed by Lockheed Martin Space Operations as a part of a larger NASA effort at the Goddard Space Flight Center (GSFC) to create a component-based, middleware-based, and standard-based general purpose ground system architecture referred as GMSEC - the GSFC Mission Services Evolution Center. CAT has been integrated into the upgraded ground systems for Tropical Rainfall Measuring Mission (TRMM) and Small Explorer (SMEX) satellites and it plays the central role in their automation effort to reduce the cost and increase the reliability for spacecraft operations. The GMSEC architecture provides a standard communication interface and protocol for components to publish/describe messages to an information bus. It also provides a standard message definition so components can send and receive messages to the bus interface rather than each other, thus reducing the component-to-component coupling, interface, protocols, and link (socket) management. With the GMSEC architecture, components can publish standard event messages to the bus for all nominal, significant, and surprising events in regard to satellite, celestial, ground system, or any other activity. In addition to sending standard event messages, each GMSEC compliant component is required to accept and process GMSEC directive request messages.

Physics Bus: An Innovative Model for Public Engagement

NASA Astrophysics Data System (ADS)

Fox, Claire

The Physics Bus is about doing science for fun. It is an innovative model for science outreach whose mission is to awaken joy and excitement in physics for all ages and walks of life - especially those underserved by science enrichment. It is a mobile exhibition of upcycled appliances-reimagined by kids-that showcase captivating physics phenomena. Inside our spaceship-themed school bus, visitors will find: a microwave ionized-gas disco-party, fog rings that shoot from a wheelbarrow tire, a tv whose electron beam is controlled by a toy keyboard, and over 20 other themed exhibits. The Physics Bus serves a wide range of public in diverse locations from local neighborhoods, urban parks and rural schools, to cross-country destinations. Its approachable, friendly and relaxed environment allows for self-paced and self-directed interactions, providing a positive and engaging experience with science. We believe that this environment enriches lives and inspires people. In this presentation we will talk about the nuts and bolts that make this model work, how the project got started, and the resources that keep it going. We will talk about the advantages of being a grassroots and community-based organization, and how programs like this can best interface with universities. We will explain the benefits of focusing on direct interactions and why our model avoids ``teaching'' physics content with words. Situating our approach within a body of research on the value of informal science we will discuss our success in capturing and engaging our audience. By the end of this presentation we hope to broaden your perception of what makes a successful outreach program and encourage you to value and support alternative outreach models such as this one. In Collaboration with: Eva Luna, Cornell University; Erik Herman, Cornell University; Christopher Bell, Ithaca City School District.

78 FR 54861 - Inspection, Repair, and Maintenance; Driver-Vehicle Inspection Report

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-06

... No. FMCSA-2012-0336] RIN 2126-AB46 Inspection, Repair, and Maintenance; Driver-Vehicle Inspection... Federal Register of August 7, 2013, regarding driver vehicle inspection reports. The corrections involve..., Vehicle and Roadside Operations Division, Office of Bus and Truck Standards and Operations, Federal Motor...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Eudy, L.

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The evaluation period in this report (January 2008 through February 2009) has been chosen to coincide with a UTC Power propulsion system changeout that occurred on January 15, 2008.

49 CFR 37.71 - Purchase or lease of new non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... public entities operating fixed route systems. 37.71 Section 37.71 Transportation Office of the Secretary... operating fixed route systems. (a) Each public entity operating a fixed route system making a solicitation after August 25, 1990, to purchase or lease a new bus or other new vehicle for use on the system, shall...

49 CFR 37.71 - Purchase or lease of new non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... public entities operating fixed route systems. 37.71 Section 37.71 Transportation Office of the Secretary... operating fixed route systems. (a) Each public entity operating a fixed route system making a solicitation after August 25, 1990, to purchase or lease a new bus or other new vehicle for use on the system, shall...

49 CFR 37.71 - Purchase or lease of new non-rail vehicles by public entities operating fixed route systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... public entities operating fixed route systems. 37.71 Section 37.71 Transportation Office of the Secretary... operating fixed route systems. (a) Each public entity operating a fixed route system making a solicitation after August 25, 1990, to purchase or lease a new bus or other new vehicle for use on the system, shall...

Network operating system

NASA Technical Reports Server (NTRS)

1985-01-01

Long-term and short-term objectives for the development of a network operating system for the Space Station are stated. The short-term objective is to develop a prototype network operating system for a 100 megabit/second fiber optic data bus. The long-term objective is to establish guidelines for writing a detailed specification for a Space Station network operating system. Major milestones are noted. Information is given in outline form.

Power-balancing instantaneous optimization energy management for a novel series-parallel hybrid electric bus

NASA Astrophysics Data System (ADS)

Sun, Dongye; Lin, Xinyou; Qin, Datong; Deng, Tao

2012-11-01

Energy management(EM) is a core technique of hybrid electric bus(HEB) in order to advance fuel economy performance optimization and is unique for the corresponding configuration. There are existing algorithms of control strategy seldom take battery power management into account with international combustion engine power management. In this paper, a type of power-balancing instantaneous optimization(PBIO) energy management control strategy is proposed for a novel series-parallel hybrid electric bus. According to the characteristic of the novel series-parallel architecture, the switching boundary condition between series and parallel mode as well as the control rules of the power-balancing strategy are developed. The equivalent fuel model of battery is implemented and combined with the fuel of engine to constitute the objective function which is to minimize the fuel consumption at each sampled time and to coordinate the power distribution in real-time between the engine and battery. To validate the proposed strategy effective and reasonable, a forward model is built based on Matlab/Simulink for the simulation and the dSPACE autobox is applied to act as a controller for hardware in-the-loop integrated with bench test. Both the results of simulation and hardware-in-the-loop demonstrate that the proposed strategy not only enable to sustain the battery SOC within its operational range and keep the engine operation point locating the peak efficiency region, but also the fuel economy of series-parallel hybrid electric bus(SPHEB) dramatically advanced up to 30.73% via comparing with the prototype bus and a similar improvement for PBIO strategy relative to rule-based strategy, the reduction of fuel consumption is up to 12.38%. The proposed research ensures the algorithm of PBIO is real-time applicability, improves the efficiency of SPHEB system, as well as suite to complicated configuration perfectly.

Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

PubMed

Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

2015-01-01

Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

Defensive Driving.

ERIC Educational Resources Information Center

Sutton, Judy

1997-01-01

Discusses management issues surrounding school busing operations within the context of tightening budgets while simultaneously serving the growing number of students with special needs. The debate on bus use for advertising is highlighted. (GR)

10 CFR 1042.235 - Statutory amendments.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) The selection of students to attend any such conference; (3) Father-son or mother-daughter activities... operations, faculty and student housing, campus shuttle bus service, campus restaurants, the bookstore, and...

Steering characteristic of an articulated bus under quasi steady maneuvering

NASA Astrophysics Data System (ADS)

Ubaidillah, Setiawan, Budi Agus; Aridharma, Airlangga Putra; Lenggana, Bhre Wangsa; Caesar, Bernardus Placenta Previo

2018-02-01

Articulated buses have been being preferred as public transportation modes due to their operational capacity. Therefore, passenger safety must be the priority of this public service vehicle. This research focused on the analytical approach of steering characteristics of an articulated bus when it maneuvered steadily. Such turning condition could be referred as a stability parameter of the bus for preliminary handling assessment. The analytical approach employed kinematics relationship between front and rear bodies as well as steering capabilities. The quasi steady model was developed to determine steering parameters such as turning radius, oversteer, and understeer. The mathematical model was useful for determining both coefficients of understeer and oversteer. The dimension of articulated bus followed a commonly used bus as utilized in Trans Jakarta busses. Based on the simulation, for one minimum center of the body, the turning radius was calculated about 8.8 m and 7.6 m at steady turning speed of 10 km/h. In neutral condition, the minimum road radius should be 6.5 m at 10 km/h and 6.9 m at 40 km/h. For two centers of the body and oversteer condition, the front body has the turning radius of 8.8 m, while, the rear body has the turning radius of 9.8 m at both turning speeds of 40 km/h. The other steering parameters were discussed accordingly.

46 CFR 112.05-3 - Main-emergency bus-tie.

Code of Federal Regulations, 2010 CFR

2010-10-01

... emergency switchboard; (b) Be arranged to prevent parallel operation of an emergency power source with any other source of electric power, except for interlock systems for momentary transfer of loads; and (c) If arranged for feedback operation, open automatically upon overload of the emergency power source before the...

49 CFR 665.23 - Fees.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Fees. 665.23 Section 665.23 Transportation Other... TRANSPORTATION BUS TESTING Operations § 665.23 Fees. (a) The operator shall charge fees in accordance with a schedule approved by FTA, which shall include prorated fees for partial testing. (b) Fees shall be prorated...

49 CFR 25.235 - Statutory amendments.

Code of Federal Regulations, 2010 CFR

2010-10-01

... conference; or (ii) The selection of students to attend any such conference; (3) Father-son or mother... operations, faculty and student housing, campus shuttle bus service, campus restaurants, the bookstore, and...

22 CFR 229.235 - Statutory amendments.

Code of Federal Regulations, 2010 CFR

2010-04-01

... conference; or (ii) The selection of students to attend any such conference; (3) Father-son or mother... operations, faculty and student housing, campus shuttle bus service, campus restaurants, the bookstore, and...

22 CFR 146.235 - Statutory amendments.

Code of Federal Regulations, 2010 CFR

2010-04-01

... conference; or (ii) The selection of students to attend any such conference; (3) Father-son or mother... operations, faculty and student housing, campus shuttle bus service, campus restaurants, the bookstore, and...

40 CFR 5.235 - Statutory amendments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Nation conference; or (ii) The selection of students to attend any such conference; (3) Father-son or... operations, faculty and student housing, campus shuttle bus service, campus restaurants, the bookstore, and...