Evaluation of urban surface parameterizations in the WRF model using measurements during the Texas Air Quality Study 2006 field campaign

NASA Astrophysics Data System (ADS)

Lee, S.-H.; Kim, S.-W.; Angevine, W. M.; Bianco, L.; McKeen, S. A.; Senff, C. J.; Trainer, M.; Tucker, S. C.; Zamora, R. J.

2010-10-01

The impact of urban surface parameterizations in the WRF (Weather Research and Forecasting) model on the simulation of local meteorological fields is investigated. The Noah land surface model (LSM), a modified LSM, and a single-layer urban canopy model (UCM) have been compared, focusing on urban patches. The model simulations were performed for 6 days from 12 August to 17 August during the Texas Air Quality Study 2006 field campaign. Analysis was focused on the Houston-Galveston metropolitan area. The model simulated temperature, wind, and atmospheric boundary layer (ABL) height were compared with observations from surface meteorological stations (Continuous Ambient Monitoring Stations, CAMS), wind profilers, the NOAA Twin Otter aircraft, and the NOAA Research Vessel Ronald H. Brown. The UCM simulation showed better results in the comparison of ABL height and surface temperature than the LSM simulations, whereas the original LSM overestimated both the surface temperature and ABL height significantly in urban areas. The modified LSM, which activates hydrological processes associated with urban vegetation mainly through transpiration, slightly reduced warm and high biases in surface temperature and ABL height. A comparison of surface energy balance fluxes in an urban area indicated the UCM reproduces a realistic partitioning of sensible heat and latent heat fluxes, consequently improving the simulation of urban boundary layer. However, the LSMs have a higher Bowen ratio than the observation due to significant suppression of latent heat flux. The comparison results suggest that the subgrid heterogeneity by urban vegetation and urban morphological characteristics should be taken into account along with the associated physical parameterizations for accurate simulation of urban boundary layer if the region of interest has a large fraction of vegetation within the urban patch. Model showed significant discrepancies in the specific meteorological conditions when nocturnal low-level jets exist and a thermal internal boundary layer over water forms.

The impact of urban canopy meteorological forcing on summer photochemistry

NASA Astrophysics Data System (ADS)

Huszár, Peter; Karlický, Jan; Belda, Michal; Halenka, Tomáš; Pišoft, Petr

2018-03-01

The regional climate model RegCM4.4, including the surface model CLM4.5, was offline coupled to the chemistry transport model CAMx version 6.30 in order to investigate the impact of the urban canopy induced meteorological changes on the longterm summer photochemistry over central Europe for the 2001-2005 period. First, the urban canopy impact on the meteorological conditions was calculated performing a reference experiment without urban landsurface considered and an experiment with urban surfaces modeled with the urban parameterization within the CLM4.5 model. In accordance with expectations, strong increases of urban surface temperatures (up to 2-3 K), decreases of wind speed (up to -1 ms-1) and increases of vertical turbulent diffusion coefficient (up to 60-70 m2s-1) were found. For the impact on chemistry, these three components were considered. Additionally, we accounted for the effect of temperature enhanced biogenic emission increase. Several experiments were performed by adding these effects one-by-one to the total impact: i.e., first, only the urban temperature impact was considered driving the chemistry model; secondly, the wind impact was added and so on. We found that the impact on biogenic emission account for minor changes in the concentrations of ozone (O3), oxides of nitrogen NOx = NO + NO2 and nitric acid (HNO3). On the other hand, the dominating component acting is the increased vertical mixing, resulting in up to 5 ppbv increase of urban ozone concentrations while causing -2 to -3 ppbv decreases and around 1 ppbv increases of NOx and HNO3 surface concentrations, respectively. The temperature impact alone results in reduction of ozone, increase in NO, decrease in NO2 and increases of HNO3. The wind impact leads, over urban areas, to ozone decreases, increases of NOx and a slight increase in HNO3. The overall impact is similar to the impact of increased vertical mixing alone. The Process Analysis (PA) technique implemented in CAMx was adopted to investigate the causes of the modeled impacts in more details. It showed that the main process contributing to the temperature impact on ozone is a dry-deposition enhancement, while the dominating process controlling the wind impact on ozone over cities is the advection reduction. In case of the impact of enhanced turbulence, PA suggests that ozone increases are, again as assumed, the result of increased downward vertical mixing supported by reduced chemical loss. Comparing the model concentrations with measurements over urban areas, a slight improvement of the model performance was achieved during afternoon hours if urban canopy forcing on chemistry via meteorology was accounted for. The study demonstrates that disregarding the urban canopy induced meteorological effects in air-quality oriented modeling studies can lead to erroneous results in the calculated species concentrations. However, it also shows that the individual components are not equally important: urban canopy induced turbulence effects dominate while the wind-speed and temperature related ones are of considerably smaller magnitude.

On the urban land-surface impact on climate over Central Europe

NASA Astrophysics Data System (ADS)

Huszar, Peter; Halenka, Tomas; Belda, Michal; Zemankova, Katerina; Zak, Michal

2014-05-01

For the purpose of qualifying and quantifying the impact of cities and in general the urban surfaces on climate over central Europe, the surface parameterization in regional climate model RegCM4 has been extended with the Single Layer Urban Canopy Model (SLUCM) for urban and suburban land surface. This can be used both in dynamic scale within BATS scheme and in a more detailed SUBBATS scale to treat the surface processes on a higher resolution subgrid. A set of experiments was performed over the period of 2005-2009 over central Europe, either without considering urban surfaces and with the SLUCM treatment. Results show a statistically significant impact of urbanized surfaces on temperature (up to 1.5 K increase in summer), on the boundary layer height (ZPBL, increases up to 50 m). Urbanization further influences surface wind with a winter decrease up to -0,6 m s-1 and both increases and decreases in summer depending the location with respect to cities and daytime (changes up to 0.3 ms-1). Urban surfaces significantly reduce evaporation and thus the humidity over the surface. This impacts in our simulations the summer precipitation rate showing decrease over cities up to - 2 mm day-1. We further showed, that significant temperature increases are not limited to the urban canopy layer but spawn the whole boundary layer. Above that, a small but statistically significant temperature decrease is modeled. The comparison with observational data showed significant improvement in modeling the monthly surface temperatures in summer and the models better describe the diurnal temperature variation reducing the afternoon and evening bias due to the UHI development, which was not captured by the model if one does not apply the urban parameterization. Sensitivity experiments were carried out as well to quantify the response of the meteorological conditions to changes in the parameters specific to the urban environment such as street width, building height, albedo of the roofs, anthropogenic heat release etc. and showed that the results are rather robust and the choice of the key SLUCM parameters impacts the results only slightly (mainly temperature, ZPBL and wind velocity). Further, the important conclusion is that statistically significant impacts are modeled not only over large urbanized areas (cities), but the influence of cities is evident over remote rural areas as well with minor or without any urban surfaces. We show that this is the result of the combined effect of the distant influence of surrounding cities and the influence of the minor local urban surface coverage.

Effects of trees on momentum exchange within and above a real urban environment

NASA Astrophysics Data System (ADS)

Salesky, S.; Giometto, M. G.; Christen, A.; Egli, P. E.; Schmid, M. F.; Tooke, T. R.; Coops, N. C.; Parlange, M. B.

2017-12-01

Large-eddy simulations (LES) are used to gain insight into the effects of trees on momentum transfer rates characterizing the atmosphere within and above a real urban canopy. Several areas are considered that are part of a neighbourhood in the city of Vancouver, BC, Canada where a small fraction of trees are taller than buildings. In this area, eight years of continuous wind and turbulence measurements are available from a 30 m meteorological tower. Buildings and vegetation geometries are obtained from airborne light detection and ranging (LiDAR) data. In the LES algorithm, buildings are accounted through an immersed boundary method, whereas vegetation is parameterized via a location-specific leaf area density. LES are performed varying wind direction and leaf area densities. Surface roughness lengths (z0) from both LES and tower measurements are sensitive to the 0 ≤ LAI/λ < 3 parameter, where LAI is the leaf area index and λ is the frontal area fraction of buildings characterizing a given canopy. For instance, tower measurements predict a 19% seasonal increase in z0, slightly lower than the 27% increase featured by LES for the most representative canopy (leaves-off LAI/λ = 0.74, leaves-on LAI/λ = 2.24). Removing vegetation from such a canopy would cause a dramatic drop of approximately 50% in z0 when compared to the reference summer value. The momentum displacement height (d) from LES also consistently increases as LAI/λ increases, due to the disproportionate amount of drag that the (few) relatively taller trees exert on the flow. Within the urban canopy, the effects of trees are twofold: on one hand, they act as a direct momentum sink for the mean flow; on the other, they reduce downward turbulent transport of high-momentum fluid, significantly reducing the wind intensity at the heights where people live and buildings consume energy.

Parameterization and sensitivity analyses of a radiative transfer model for remote sensing plant canopies

NASA Astrophysics Data System (ADS)

Hall, Carlton Raden

A major objective of remote sensing is determination of biochemical and biophysical characteristics of plant canopies utilizing high spectral resolution sensors. Canopy reflectance signatures are dependent on absorption and scattering processes of the leaf, canopy properties, and the ground beneath the canopy. This research investigates, through field and laboratory data collection, and computer model parameterization and simulations, the relationships between leaf optical properties, canopy biophysical features, and the nadir viewed above-canopy reflectance signature. Emphasis is placed on parameterization and application of an existing irradiance radiative transfer model developed for aquatic systems. Data and model analyses provide knowledge on the relative importance of leaves and canopy biophysical features in estimating the diffuse absorption a(lambda,m-1), diffuse backscatter b(lambda,m-1), beam attenuation alpha(lambda,m-1), and beam to diffuse conversion c(lambda,m-1 ) coefficients of the two-flow irradiance model. Data sets include field and laboratory measurements from three plant species, live oak (Quercus virginiana), Brazilian pepper (Schinus terebinthifolius) and grapefruit (Citrus paradisi) sampled on Cape Canaveral Air Force Station and Kennedy Space Center Florida in March and April of 1997. Features measured were depth h (m), projected foliage coverage PFC, leaf area index LAI, and zenith leaf angle. Optical measurements, collected with a Spectron SE 590 high sensitivity narrow bandwidth spectrograph, included above canopy reflectance, internal canopy transmittance and reflectance and bottom reflectance. Leaf samples were returned to laboratory where optical and physical and chemical measurements of leaf thickness, leaf area, leaf moisture and pigment content were made. A new term, the leaf volume correction index LVCI was developed and demonstrated in support of model coefficient parameterization. The LVCI is based on angle adjusted leaf thickness Ltadj, LAI, and h (m). Its function is to translate leaf level estimates of diffuse absorption and backscatter to the canopy scale allowing the leaf optical properties to directly influence above canopy estimates of reflectance. The model was successfully modified and parameterized to operate in a canopy scale and a leaf scale mode. Canopy scale model simulations produced the best results. Simulations based on leaf derived coefficients produced calculated above canopy reflectance errors of 15% to 18%. A comprehensive sensitivity analyses indicated the most important parameters were beam to diffuse conversion c(lambda, m-1), diffuse absorption a(lambda, m-1), diffuse backscatter b(lambda, m-1), h (m), Q, and direct and diffuse irradiance. Sources of error include the estimation procedure for the direct beam to diffuse conversion and attenuation coefficients and other field and laboratory measurement and analysis errors. Applications of the model include creation of synthetic reflectance data sets for remote sensing algorithm development, simulations of stress and drought on vegetation reflectance signatures, and the potential to estimate leaf moisture and chemical status.

Explaining the convector effect in canopy turbulence by means of large-eddy simulation

DOE PAGES

Banerjee, Tirtha; De Roo, Frederik; Mauder, Matthias

2017-06-20

Semi-arid forests are found to sustain a massive sensible heat flux in spite of having a low surface to air temperature difference by lowering the aerodynamic resistance to heat transfer ( r H) – a property called the canopy convector effect (CCE). In this work large-eddy simulations are used to demonstrate that the CCE appears more generally in canopy turbulence. It is indeed a generic feature of canopy turbulence: r H of a canopy is found to reduce with increasing unstable stratification, which effectively increases the aerodynamic roughness for the same physical roughness of the canopy. This relation offers a sufficientmore » condition to construct a general description of the CCE. In addition, we review existing parameterizations for r H from the evapotranspiration literature and test to what extent they are able to capture the CCE, thereby exploring the possibility of an improved parameterization.« less

A New Canopy Integration Factor

NASA Astrophysics Data System (ADS)

Badgley, G.; Anderegg, L. D. L.; Baker, I. T.; Berry, J. A.

2017-12-01

Ecosystem modelers have long debated how to best represent within-canopy heterogeneity. Can one big leaf represent the full range of canopy physiological responses? Or you need two leaves - sun and shade - to get things right? Is it sufficient to treat the canopy as a diffuse medium? Or would it be better to explicitly represent separate canopy layers? These are open questions that have been subject of an enormous amount of research and scrutiny. Yet regardless of how the canopy is represented, each model must grapple with correctly parameterizing its canopy in a way that properly translates leaf-level processes to the canopy and ecosystem scale. We present a new approach for integrating whole-canopy biochemistry by combining remote sensing with ecological theory. Using the Simple Biosphere model (SiB), we redefined how SiB scales photosynthetic processes from leaf-to-canopy as a function of satellite-derived measurements of solar-induced chlorophyll fluorescence (SIF). Across multiple long-term study sites, our approach improves the accuracy of daily modeled photosynthesis by as much as 25 percent. We share additional insights on how SIF might be more directly integrated into photosynthesis models, as well as present ideas for harnessing SIF to more accurately parameterize canopy biochemical variables.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maurer, K. D.; Bohrer, G.; Kenny, W. T.

Surface roughness parameters, namely the roughness length and displacement height, are an integral input used to model surface fluxes. However, most models assume these parameters to be a fixed property of plant functional type and disregard the governing structural heterogeneity and dynamics. In this study, we use large-eddy simulations to explore, in silico, the effects of canopy-structure characteristics on surface roughness parameters. We performed a virtual experiment to test the sensitivity of resolved surface roughness to four axes of canopy structure: (1) leaf area index, (2) the vertical profile of leaf density, (3) canopy height, and (4) canopy gap fraction.more » We found roughness parameters to be highly variable, but uncovered positive relationships between displacement height and maximum canopy height, aerodynamic canopy height and maximum canopy height and leaf area index, and eddy-penetration depth and gap fraction. We also found negative relationships between aerodynamic canopy height and gap fraction, as well as between eddy-penetration depth and maximum canopy height and leaf area index. We generalized our model results into a virtual "biometric" parameterization that relates roughness length and displacement height to canopy height, leaf area index, and gap fraction. Using a decade of wind and canopy-structure observations in a site in Michigan, we tested the effectiveness of our model-driven biometric parameterization approach in predicting the friction velocity over heterogeneous and disturbed canopies. We compared the accuracy of these predictions with the friction-velocity predictions obtained from the common simple approximation related to canopy height, the values calculated with large-eddy simulations of the explicit canopy structure as measured by airborne and ground-based lidar, two other parameterization approaches that utilize varying canopy-structure inputs, and the annual and decadal means of the surface roughness parameters at the site from meteorological observations. We found that the classical representation of constant roughness parameters (in space and time) as a fraction of canopy height performed relatively well. Nonetheless, of the approaches we tested, most of the empirical approaches that incorporate seasonal and interannual variation of roughness length and displacement height as a function of the dynamics of canopy structure produced more precise and less biased estimates for friction velocity than models with temporally invariable parameters.« less

Impacts of differing aerodynamic resistance formulae on modeled energy exchange at the above-canopy/within-canopy/soil interface

USDA-ARS?s Scientific Manuscript database

Application of the Two-Source Energy Balance (TSEB) Model using land surface temperature (LST) requires aerodynamic resistance parameterizations for the flux exchange above the canopy layer, within the canopy air space and at the soil/substrate surface. There are a number of aerodynamic resistance f...

On the Pollutant Plume Dispersion in the Urban Canopy Layer over 2D Idealized Street Canyons: A Large-Eddy Simulation Approach

NASA Astrophysics Data System (ADS)

Wong, Colman C. C.; Liu, Chun-Ho

2010-05-01

Anthropogenic emissions are the major sources of air pollutants in urban areas. To improve the air quality in dense and mega cities, a simple but reliable prediction method is necessary. In the last five decades, the Gaussian pollutant plume model has been widely used for the estimation of air pollutant distribution in the atmospheric boundary layer (ABL) in an operational manner. Whereas, it was originally designed for rural areas with rather open and flat terrain. The recirculating flows below the urban canopy layer substantially modify the near-ground urban wind environment and so does the pollutant distribution. Though the plume height and dispersion are often adjusted empirically, the accuracy of applying the Gaussian pollutant plume model in urban areas, of which the bottom of the flow domain consists of numerous inhomogeneous buildings, is unclear. To elucidate the flow and pollutant transport, as well as to demystify the uncertainty of employing the Gaussian pollutant plume model over urban roughness, this study was performed to examine how the Gaussian-shape pollutant plume in the urban canopy layer is modified by the idealized two-dimensional (2D) street canyons at the bottom of the ABL. The specific objective is to develop a parameterization so that the geometric effects of urban morphology on the operational pollutant plume dispersion models could be taken into account. Because atmospheric turbulence is the major means of pollutant removal from street canyons to the ABL, the large-eddy simulation (LES) was adopted to calculate explicitly the flows and pollutant transport in the urban canopy layer. The subgrid-scale (SGS) turbulent kinetic energy (TKE) conservation was used to model the SGS processes in the incompressible, isothermal conditions. The computational domain consists of 12 identical idealized street canyons of unity aspect ratio which were placed evenly in the streamwise direction. Periodic boundary conditions (BCs) for the flow were applied in the horizontal and the spanwise directions. The prevalent wind was driven by a background pressure gradient in the roughness sublayer only, no background force was prescribed inside the street canyons. While the periodic BC of pollutant was used in the spanwise direction, zero pollutant and an open BC were applied, respectively, at the inflow and outflow of the streamwise extent to avoid pollutant being reflected back into the computational domain. The ground of the first street canyon was assigned as the pollutant source on which a BC of constant pollutant concentration was prescribed. The LES results showed that, in the neutrally stratified ABL, the pollutant distribution in the urban canopy layer resembled the Gaussian plume shape in general even recirculating flows were observed in the street canyons. The roof-level horizontal profile of pollutant concentration in the streamwise direction showed that the sharp drop on the leeward side of each street canyon was likely caused by the air and pollutant entrainments. On the windward side of each street canyon, a mild increase in pollutant concentration was observed that did not follow the Gaussian plume closely. Those deviations extended to a certain height over the roof level of the street canyons. It in turn suggests that the Gaussian pollutant plume model should be applied with caution in the urban canopy layer in the vicinity over urban roughness. To further analyze the effects of urban roughness on the plume dispersion in detail, a few LES calculations with different aspect ratios are currently being undertaken so as to compare with the current LES results.

Large-eddy simulations of surface roughness parameter sensitivity to canopy-structure characteristics

DOE PAGES

Maurer, K. D.; Bohrer, G.; Kenny, W. T.; ...

2015-04-30

Surface roughness parameters, namely the roughness length and displacement height, are an integral input used to model surface fluxes. However, most models assume these parameters to be a fixed property of plant functional type and disregard the governing structural heterogeneity and dynamics. In this study, we use large-eddy simulations to explore, in silico, the effects of canopy-structure characteristics on surface roughness parameters. We performed a virtual experiment to test the sensitivity of resolved surface roughness to four axes of canopy structure: (1) leaf area index, (2) the vertical profile of leaf density, (3) canopy height, and (4) canopy gap fraction.more » We found roughness parameters to be highly variable, but uncovered positive relationships between displacement height and maximum canopy height, aerodynamic canopy height and maximum canopy height and leaf area index, and eddy-penetration depth and gap fraction. We also found negative relationships between aerodynamic canopy height and gap fraction, as well as between eddy-penetration depth and maximum canopy height and leaf area index. We generalized our model results into a virtual "biometric" parameterization that relates roughness length and displacement height to canopy height, leaf area index, and gap fraction. Using a decade of wind and canopy-structure observations in a site in Michigan, we tested the effectiveness of our model-driven biometric parameterization approach in predicting the friction velocity over heterogeneous and disturbed canopies. We compared the accuracy of these predictions with the friction-velocity predictions obtained from the common simple approximation related to canopy height, the values calculated with large-eddy simulations of the explicit canopy structure as measured by airborne and ground-based lidar, two other parameterization approaches that utilize varying canopy-structure inputs, and the annual and decadal means of the surface roughness parameters at the site from meteorological observations. We found that the classical representation of constant roughness parameters (in space and time) as a fraction of canopy height performed relatively well. Nonetheless, of the approaches we tested, most of the empirical approaches that incorporate seasonal and interannual variation of roughness length and displacement height as a function of the dynamics of canopy structure produced more precise and less biased estimates for friction velocity than models with temporally invariable parameters.« less

Large-eddy simulations of surface roughness parameter sensitivity to canopy-structure characteristics

NASA Astrophysics Data System (ADS)

Maurer, K. D.; Bohrer, G.; Kenny, W. T.; Ivanov, V. Y.

2015-04-01

Surface roughness parameters, namely the roughness length and displacement height, are an integral input used to model surface fluxes. However, most models assume these parameters to be a fixed property of plant functional type and disregard the governing structural heterogeneity and dynamics. In this study, we use large-eddy simulations to explore, in silico, the effects of canopy-structure characteristics on surface roughness parameters. We performed a virtual experiment to test the sensitivity of resolved surface roughness to four axes of canopy structure: (1) leaf area index, (2) the vertical profile of leaf density, (3) canopy height, and (4) canopy gap fraction. We found roughness parameters to be highly variable, but uncovered positive relationships between displacement height and maximum canopy height, aerodynamic canopy height and maximum canopy height and leaf area index, and eddy-penetration depth and gap fraction. We also found negative relationships between aerodynamic canopy height and gap fraction, as well as between eddy-penetration depth and maximum canopy height and leaf area index. We generalized our model results into a virtual "biometric" parameterization that relates roughness length and displacement height to canopy height, leaf area index, and gap fraction. Using a decade of wind and canopy-structure observations in a site in Michigan, we tested the effectiveness of our model-driven biometric parameterization approach in predicting the friction velocity over heterogeneous and disturbed canopies. We compared the accuracy of these predictions with the friction-velocity predictions obtained from the common simple approximation related to canopy height, the values calculated with large-eddy simulations of the explicit canopy structure as measured by airborne and ground-based lidar, two other parameterization approaches that utilize varying canopy-structure inputs, and the annual and decadal means of the surface roughness parameters at the site from meteorological observations. We found that the classical representation of constant roughness parameters (in space and time) as a fraction of canopy height performed relatively well. Nonetheless, of the approaches we tested, most of the empirical approaches that incorporate seasonal and interannual variation of roughness length and displacement height as a function of the dynamics of canopy structure produced more precise and less biased estimates for friction velocity than models with temporally invariable parameters.

Chemical transport models: the combined non-local diffusion and mixing schemes, and calculation of in-canopy resistance for dry deposition fluxes.

PubMed

Mihailovic, Dragutin T; Alapaty, Kiran; Podrascanin, Zorica

2009-03-01

Improving the parameterization of processes in the atmospheric boundary layer (ABL) and surface layer, in air quality and chemical transport models. To do so, an asymmetrical, convective, non-local scheme, with varying upward mixing rates is combined with the non-local, turbulent, kinetic energy scheme for vertical diffusion (COM). For designing it, a function depending on the dimensionless height to the power four in the ABL is suggested, which is empirically derived. Also, we suggested a new method for calculating the in-canopy resistance for dry deposition over a vegetated surface. The upward mixing rate forming the surface layer is parameterized using the sensible heat flux and the friction and convective velocities. Upward mixing rates varying with height are scaled with an amount of turbulent kinetic energy in layer, while the downward mixing rates are derived from mass conservation. The vertical eddy diffusivity is parameterized using the mean turbulent velocity scale that is obtained by the vertical integration within the ABL. In-canopy resistance is calculated by integration of inverse turbulent transfer coefficient inside the canopy from the effective ground roughness length to the canopy source height and, further, from its the canopy height. This combination of schemes provides a less rapid mass transport out of surface layer into other layers, during convective and non-convective periods, than other local and non-local schemes parameterizing mixing processes in the ABL. The suggested method for calculating the in-canopy resistance for calculating the dry deposition over a vegetated surface differs remarkably from the commonly used one, particularly over forest vegetation. In this paper, we studied the performance of a non-local, turbulent, kinetic energy scheme for vertical diffusion combined with a non-local, convective mixing scheme with varying upward mixing in the atmospheric boundary layer (COM) and its impact on the concentration of pollutants calculated with chemical and air-quality models. In addition, this scheme was also compared with a commonly used, local, eddy-diffusivity scheme. Simulated concentrations of NO2 by the COM scheme and new parameterization of the in-canopy resistance are closer to the observations when compared to those obtained from using the local eddy-diffusivity scheme. Concentrations calculated with the COM scheme and new parameterization of in-canopy resistance, are in general higher and closer to the observations than those obtained by the local, eddy-diffusivity scheme (on the order of 15-22%). To examine the performance of the scheme, simulated and measured concentrations of a pollutant (NO2) were compared for the years 1999 and 2002. The comparison was made for the entire domain used in simulations performed by the chemical European Monitoring and Evaluation Program Unified model (version UNI-ACID, rv2.0) where schemes were incorporated.

Quality and sensitivity of high-resolution numerical simulation of urban heat islands

NASA Astrophysics Data System (ADS)

Li, Dan; Bou-Zeid, Elie

2014-05-01

High-resolution numerical simulations of the urban heat island (UHI) effect with the widely-used Weather Research and Forecasting (WRF) model are assessed. Both the sensitivity of the results to the simulation setup, and the quality of the simulated fields as representations of the real world, are investigated. Results indicate that the WRF-simulated surface temperatures are more sensitive to the planetary boundary layer (PBL) scheme choice during nighttime, and more sensitive to the surface thermal roughness length parameterization during daytime. The urban surface temperatures simulated by WRF are also highly sensitive to the urban canopy model (UCM) used. The implementation in this study of an improved UCM (the Princeton UCM or PUCM) that allows the simulation of heterogeneous urban facets and of key hydrological processes, together with the so-called CZ09 parameterization for the thermal roughness length, significantly reduce the bias (<1.5 °C) in the surface temperature fields as compared to satellite observations during daytime. The boundary layer potential temperature profiles are captured by WRF reasonable well at both urban and rural sites; the biases in these profiles relative to aircraft-mounted senor measurements are on the order of 1.5 °C. Changing UCMs and PBL schemes does not alter the performance of WRF in reproducing bulk boundary layer temperature profiles significantly. The results illustrate the wide range of urban environmental conditions that various configurations of WRF can produce, and the significant biases that should be assessed before inferences are made based on WRF outputs. The optimal set-up of WRF-PUCM developed in this paper also paves the way for a confident exploration of the city-scale impacts of UHI mitigation strategies in the companion paper (Li et al 2014).

Mean and turbulent flow downstream of a low-intensity fire: influence of canopy and background atmospheric conditions

Treesearch

Michael T. Kiefer; Warren E. Heilman; Shiyuan Zhong; Joseph J. Charney; Xindi Bian

2015-01-01

This study examines the sensitivity of mean and turbulent flow in the planetary boundary layer and roughness sublayer to a low-intensity fire and evaluates whether the sensitivity is dependent on canopy and background atmospheric properties. The ARPS-CANOPY model, a modified version of the Advanced Regional Prediction System (ARPS) model with a canopy parameterization...

Comparing large eddy simulations and measurements of the turbulent kinetic energy budget in an urban canopy layer

NASA Astrophysics Data System (ADS)

Parlange, M. B.; Giometto, M. G.; Meneveau, C. V.; Fang, J.; Christen, A.

2013-12-01

Local turbulent kinetic energy (TKE) in the Urban Canopy Layer (UCL) is highly dependent on the actual configuration of obstacles relative to mean wind and stability. For many applications, building-resolving information is neither required nor feasible, and simply beyond the numerical capabilities of operational systems. Common urban canopy parameterizations (UCP) used in dispersion and mesoscale forecasting models hence rely on a horizontally averaged approach, where the UCL is represented as a 1D column, often for simplified geometries such as infinite street canyons. We use Large Eddy Simulations (LES) of the airflow over and within a realistic urban geometry in the city of Basel, Switzerland to determine all terms of the TKE budget in order to guide and validate current approaches used in UCPs. A series of high-resolution LES runs of the fully developed flow are performed in order to characterize the TKE budget terms in a horizontally averaged frame of view for various directions of the approaching flow under neutral conditions. Equations are solved on a regular domain with a horizontal resolution of 2 m. A Lagrangian scale-dependent LES model is adopted to parametrize the subgrid-scale stresses and buildings are taken into account adopting an immersed boundary approach with the geometry taken from a highly accurate digital building model. The modeled (periodic) domain is centered on the location of a 32 m tall tower, where measurements of turbulence were performed, during the BUBBLE program in 2001/02 (Rotach et al., Theor. Appl. Clim., 82, 231-261, 2005). Selected terms of the TKE budget were inferred from six levels of ultrasonic anemometer measurements operated over nearly a full year between ground level and two times the mean building height. This contribution answers the questions: (1) How well do TKE budget terms calculated by the LES at the exact tower location match the single point measurements on the tower under comparable conditions? (2) How representative are the single-point measurements at the tower-location compared to the horizontally-averaged TKE budget in the entire urban domain? (3) How important are non-measurable terms of the TKE budget (wake production, dispersive transport, pressure transport) under the current real urban geometry? Our results show good statistical agreement between tower measurements and numerically resolved quantities, validating the model and confirming our immersed boundary approach in the LES a valuable tool to study turbulence and dispersion within real UCLs. Turbulent kinetic energy (TKE) in the UCL is primarily produced at roof-level, and turbulence is transported down into the cavities of the urban canopy (street canyons, backyards). From our results it is also clear how tower measurements cannot be used to quantify all terms in a horizontally-averaged view and the non-measured dispersive terms are important in a real canopy.

A New, Two-layer Canopy Module For The Detailed Snow Model SNOWPACK

NASA Astrophysics Data System (ADS)

Gouttevin, I.; Lehning, M.; Jonas, T.; Gustafsson, D.; Mölder, M.

2014-12-01

A new, two-layer canopy module with thermal inertia for the detailed snow model SNOWPACK is presented. Compared to the old, one-layered canopy formulation with no heat mass, this module now offers a level of physical detail consistent with the detailed snow and soil representation in SNOWPACK. The new canopy model is designed to reproduce the difference in thermal regimes between leafy and woody canopy elements and their impact on the underlying snowpack energy balance. The new model is validated against data from an Alpine and a boreal site. Comparisons of modelled sub-canopy thermal radiations to stand-scale observations at Alptal, Switzerland, demonstrate the improvements induced by our new parameterizations. The main effect is a more realistic simulation of the canopy night-time drop in temperatures. The lower drop is induced by both thermal inertia and the two-layer representation. A specific result is that such a performance cannot be achieved by a single-layered canopy model. The impact of the new parameterizations on the modelled dynamics of the sub-canopy snowpack is analysed and yields consistent results, but the frequent occurrence of mixed-precipitation events at Alptal prevents a conclusive assessment of model performances against snow data.Without specific tuning, the model is also able to reproduce the measured summertime tree trunk temperatures and biomass heat storage at the boreal site of Norunda, Sweden, with an increased accuracy in amplitude and phase. Overall, the SNOWPACK model with its enhanced canopy module constitutes a unique (in its physical process representation) atmosphere-to-soil-through-canopy-and-snow modelling chain.

A Testbed for Model Development

NASA Astrophysics Data System (ADS)

Berry, J. A.; Van der Tol, C.; Kornfeld, A.

2014-12-01

Carbon cycle and land-surface models used in global simulations need to be computationally efficient and have a high standard of software engineering. These models also make a number of scaling assumptions to simplify the representation of complex biochemical and structural properties of ecosystems. This makes it difficult to use these models to test new ideas for parameterizations or to evaluate scaling assumptions. The stripped down nature of these models also makes it difficult to "connect" with current disciplinary research which tends to be focused on much more nuanced topics than can be included in the models. In our opinion/experience this indicates the need for another type of model that can more faithfully represent the complexity ecosystems and which has the flexibility to change or interchange parameterizations and to run optimization codes for calibration. We have used the SCOPE (Soil Canopy Observation, Photochemistry and Energy fluxes) model in this way to develop, calibrate, and test parameterizations for solar induced chlorophyll fluorescence, OCS exchange and stomatal parameterizations at the canopy scale. Examples of the data sets and procedures used to develop and test new parameterizations are presented.

Effects of trees on mean wind, turbulence and momentum exchange within and above a real urban environment

NASA Astrophysics Data System (ADS)

Giometto, M. G.; Christen, A.; Egli, P. E.; Schmid, M. F.; Tooke, R. T.; Coops, N. C.; Parlange, M. B.

2017-08-01

Large-eddy simulations (LES) are used to gain insight into the effects of trees on turbulence, aerodynamic parameters, and momentum transfer rates characterizing the atmosphere within and above a real urban canopy. Several areas are considered that are part of a neighborhood in the city of Vancouver, BC, Canada where a small fraction of trees are taller than buildings. In this area, eight years of continuous wind and turbulence measurements are available from a 30 m meteorological tower. Data from airborne light detection and ranging (LiDAR) are used to represent both buildings and vegetation at the LES resolution. In the LES algorithm, buildings are accounted through an immersed boundary method, whereas vegetation is parameterized via a location-specific leaf area density. LES are performed including and excluding vegetation from the considered urban areas, varying wind direction and leaf area density. Surface roughness lengths (z0) from both LES and tower measurements are sensitive to the 0 ≤ LAI /λfb < 3 parameter, where LAI is the leaf area index and λfb is the frontal area fraction of buildings characterizing a given canopy. For instance, tower measurements predict a 19% seasonal increase in z0, slightly lower than the 27% increase featured by LES for the most representative canopy (leaves-off LAI / λfSUP>b = 0.74 , leaves-on LAI /λfb = 2.24). Removing vegetation from such a canopy would cause a dramatic drop of approximately 50% in z0 when compared to the reference summer value. The momentum displacement height (d) from LES also consistently increases as LAI / λfb increases, due in large part to the disproportionate amount of drag that the (few) relatively taller trees exert on the flow. LES and measurements both predict an increase in the ratio of turbulent to mean kinetic energy (TKE/MKE) at the tower sampling height going from winter to summer, and LES also show how including vegetation results in a more (positive) negatively skewed (horizontal) vertical velocity distribution - reflecting a more intermittent velocity field which favors sweep motions when compared to ejections. Within the urban canopy, the effects of trees are twofold: on one hand, they act as a direct momentum sink for the mean flow; on the other, they reduce downward turbulent transport of high-momentum fluid, significantly reducing the wind intensity at the heights where people live and buildings consume energy.

Gainesville's urban forest canopy cover

Treesearch

Francisco Escobedo; Jennifer A. Seitz; Wayne Zipperer

2009-01-01

Ecosystem benefits from trees are linked directly to the amount of healthy urban forest canopy cover. Urban forest cover is dynamic and changes over time due to factors such as urban development, windstorms, tree removals, and growth. The amount of a city's canopy cover depends on its land use, climate, and people's preferences. This fact sheet examines how...

A numerical study of atmospheric perturbations induced by heat from a wildland fire: sensitivity to vertical canopy structure and heat source strength

Treesearch

Michael T. Kiefer; Shiyuan Zhong; Warren E. Heilman; Joseph J. Charney; Xindi Bian

2018-01-01

An improved understanding of atmospheric perturbations within and above a forest during a wildland fire has relevance to many aspects of wildland fires including fire spread, smoke transport and dispersion, and tree mortality. In this study, the ARPS-CANOPY model, a version of the Advanced Regional Prediction System (ARPS) model with a canopy parameterization, is...

Estimating the influence of different urban canopy cover types on atmospheric particulate matter (PM10) pollution abatement in London UK.

NASA Astrophysics Data System (ADS)

Tallis, Matthew; Freer-Smith, Peter; Sinnett, Danielle; Aylott, Matthew; Taylor, Gail

2010-05-01

In the urban environment atmospheric pollution by PM10 (particulate matter with a diameter less than 10 x 10-6 m) is a problem that can have adverse effects on human health, particularly increasing rates of respiratory disease. The main contributors to atmospheric PM10 in the urban environment are road traffic, industry and power production. The urban tree canopy is a receptor for removing PM10s from the atmosphere due to the large surface areas generated by leaves and air turbulence created by the structure of the urban forest. In this context urban greening has long been known as a mechanism to contribute towards PM10 removal from the air, furthermore, tree canopy cover has a role in contributing towards a more sustainable urban environment. The work reported here has been carried out within the BRIDGE project (SustainaBle uRban plannIng Decision support accountinG for urban mEtabolism). The aim of this project is to assess the fluxes of energy, water, carbon dioxide and particulates within the urban environment and develope a DSS (Decision Support System) to aid urban planners in sustainable development. A combination of published urban canopy cover data from ground, airborne and satellite based surveys was used. For each of the 33 London boroughs the urban canopy was classified to three groups, urban woodland, street trees and garden trees and each group quantified in terms of ground cover. The total [PM10] for each borough was taken from the LAEI (London Atmospheric Emissions Inventory 2006) and the contribution to reducing [PM10] was assessed for each canopy type. Deposition to the urban canopy was assessed using the UFORE (Urban Forest Effects Model) approach. Deposition to the canopy, boundary layer height and percentage reduction of the [PM10] in the atmosphere was assessed using both hourly meterological data and [PM10] and seasonal data derived from annual models. Results from hourly and annual data were compared with measured values. The model was then applied to future predictions of annual [PM10] and future canopy cover scenarios for London. The contribution of each canopy type subjected to the different atmospheric [PM10] of the 33 London boroughs now and in the future will be discussed. Implementing these findings into a decision support system (DSS) for sustainable urban planning will also be discussed.

A comparison of three methods for measuring local urban tree canopy cover

Treesearch

Kristen L. King; Dexter H. Locke

2013-01-01

Measurements of urban tree canopy cover are crucial for managing urban forests and required for the quantification of the benefits provided by trees. These types of data are increasingly used to secure funding and justify large-scale planting programs in urban areas. Comparisons of tree canopy measurement methods have been conducted before, but a rapidly evolving set...

Scalar Dispersion from Point Sources in a Realistic Urban Environment

NASA Astrophysics Data System (ADS)

Salesky, S.; Giometto, M. G.; Christen, A.; Parlange, M. B.

2016-12-01

Accurate modeling of scalar dispersion within and above urban canopies is critical to properly predict air quality and dispersion (e.g. accidental contaminant release) in urban environments. We perform large eddy simulations (LES) of scalar dispersion from point sources in a typical North American neighborhood using topography and foliage density derived from airborne LIDAR scans with 1 m resolution in Vancouver, BC, Canada. The added drag force due to trees is parameterized in the LES as a function of the leaf area density (LAD) profile. Conversely, drag from buildings is accounted for using a direct forcing approach immersed-boundary method. The scalar advection-diffusion equation is discretized in a finite-volume framework, and accurate mass conservation is enforced through a recently developed Cartesian cut cell method. Simulations are performed with trees for different values of LAD, representative of summer and winter conditions, as well as a case without trees. The effects of varying mean wind direction (derived from observed wind climatologies) on dispersion patterns are also considered. Scalar release locations in the LES are informed by spatially distributed measurements of carbon dioxide concentration; CO2 is used as a tracer for fossil fuel emissions, since source strengths are well-known and the contribution from biological processes in this setting is small (<10%). The effects of leaf area density, source height, and wind direction on scalar statistics including the growth of the mean concentration plume and the fraction that escapes the urban canopy layer will be considered. In a companion study, the presence of trees was found to strongly modify sweep and ejection patterns for the momentum flux; here we consider the related issue of how vegetation influences coherent structures responsible for scalar transport.

Assessing urban forest canopy cover using airborne or satellite imagery

Treesearch

Jeffrey T. Walton; David J. Nowak; Eric J. Greenfield

2008-01-01

With the availability of many sources of imagery and various digital classification techniques, assessing urban forest canopy cover is readily accessible to most urban forest managers. Understanding the capability and limitations of various types of imagery and classification methods is essential to interpreting canopy cover values. An overview of several remote...

Improving representation of canopy temperatures for modeling subcanopy incoming longwave radiation to the snow surface

NASA Astrophysics Data System (ADS)

Webster, Clare; Rutter, Nick; Jonas, Tobias

2017-09-01

A comprehensive analysis of canopy surface temperatures was conducted around a small and large gap at a forested alpine site in the Swiss Alps during the 2015 and 2016 snowmelt seasons (March-April). Canopy surface temperatures within the small gap were within 2-3°C of measured reference air temperature. Vertical and horizontal variations in canopy surface temperatures were greatest around the large gap, varying up to 18°C above measured reference air temperature during clear-sky days. Nighttime canopy surface temperatures around the study site were up to 3°C cooler than reference air temperature. These measurements were used to develop a simple parameterization for correcting reference air temperature for elevated canopy surface temperatures during (1) nighttime conditions (subcanopy shortwave radiation is 0 W m-2) and (2) periods of increased subcanopy shortwave radiation >400 W m-2 representing penetration of shortwave radiation through the canopy. Subcanopy shortwave and longwave radiation collected at a single point in the subcanopy over a 24 h clear-sky period was used to calculate a nighttime bulk offset of 3°C for scenario 1 and develop a multiple linear regression model for scenario 2 using reference air temperature and subcanopy shortwave radiation to predict canopy surface temperature with a root-mean-square error (RMSE) of 0.7°C. Outside of these two scenarios, reference air temperature was used to predict subcanopy incoming longwave radiation. Modeling at 20 radiometer locations throughout two snowmelt seasons using these parameterizations reduced the mean bias and RMSE to below 10 W m s-2 at all locations.

Assessment of canopy chlorophyll content retrieval in maize and soybean: Implications of hysteresis on the development of generic algorithms

DOE PAGES

Peng, Yi; Nguy-Robertson, Anthony; Arkebauer, Timothy; ...

2017-03-02

Here, canopy chlorophyll content (Chl) closely relates to plant photosynthetic capacity, nitrogen status and productivity. The goal of this study is to develop remote sensing techniques for accurate estimation of canopy Chl during the entire growing season without re-parameterization of algorithms for two contrasting crop species, maize and soybean. These two crops represent different biochemical mechanisms of photosynthesis, leaf structure and canopy architecture. The relationships between canopy Chl and reflectance, collected at close range and resampled to bands of the Multi Spectral Instrument (MSI) aboard Sentinel-2, were analyzed in samples taken across the entirety of the growing seasons in threemore » irrigated and rainfed sites located in eastern Nebraska between 2001 and 2005. Crop phenology was a factor strongly influencing the reflectance of both maize and soybean. Substantial hysteresis of the reflectance vs. canopy Chl relationship existed between the vegetative and reproductive stages. The effect of the hysteresis on vegetation indices (VI), applied for canopy Chl estimation, depended on the bands used and their formulation. The hysteresis greatly affected the accuracy of canopy Chl estimation by widely-used VIs with near infrared (NIR) and red reflectance (e.g., normalized difference vegetation index (NDVI), enhanced vegetation index (EVI) and simple ratio (SR)). VIs that use red edge and NIR bands (e.g., red edge chlorophyll index (CIred edge), red edge NDVI and the MERIS terrestrial chlorophyll index (MTCI)) were minimally affected by crop phenology (i.e., they exhibited little hysteresis) and were able to accurately estimate canopy Chl in two crops without algorithm re-parameterization and, thus, were found to be the best candidates for generic algorithms to estimate crop Chl using the surface reflectance products of MSI Sentinel-2.« less

Assessment of canopy chlorophyll content retrieval in maize and soybean: Implications of hysteresis on the development of generic algorithms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, Yi; Nguy-Robertson, Anthony; Arkebauer, Timothy

Here, canopy chlorophyll content (Chl) closely relates to plant photosynthetic capacity, nitrogen status and productivity. The goal of this study is to develop remote sensing techniques for accurate estimation of canopy Chl during the entire growing season without re-parameterization of algorithms for two contrasting crop species, maize and soybean. These two crops represent different biochemical mechanisms of photosynthesis, leaf structure and canopy architecture. The relationships between canopy Chl and reflectance, collected at close range and resampled to bands of the Multi Spectral Instrument (MSI) aboard Sentinel-2, were analyzed in samples taken across the entirety of the growing seasons in threemore » irrigated and rainfed sites located in eastern Nebraska between 2001 and 2005. Crop phenology was a factor strongly influencing the reflectance of both maize and soybean. Substantial hysteresis of the reflectance vs. canopy Chl relationship existed between the vegetative and reproductive stages. The effect of the hysteresis on vegetation indices (VI), applied for canopy Chl estimation, depended on the bands used and their formulation. The hysteresis greatly affected the accuracy of canopy Chl estimation by widely-used VIs with near infrared (NIR) and red reflectance (e.g., normalized difference vegetation index (NDVI), enhanced vegetation index (EVI) and simple ratio (SR)). VIs that use red edge and NIR bands (e.g., red edge chlorophyll index (CIred edge), red edge NDVI and the MERIS terrestrial chlorophyll index (MTCI)) were minimally affected by crop phenology (i.e., they exhibited little hysteresis) and were able to accurately estimate canopy Chl in two crops without algorithm re-parameterization and, thus, were found to be the best candidates for generic algorithms to estimate crop Chl using the surface reflectance products of MSI Sentinel-2.« less

Canopy rainfall partitioning across an urbanization gradient in forest structure as characterized by terrestrial LiDAR

NASA Astrophysics Data System (ADS)

Mesta, D. C.; Van Stan, J. T., II; Yankine, S. A.; Cote, J. F.; Jarvis, M. T.; Hildebrandt, A.; Friesen, J.; Maldonado, G.

2017-12-01

As urbanization expands, greater forest area is shifting from natural stand structures to urban stand structures, like forest fragments and landscaped tree rows. Changes in forest canopy structure have been found to drastically alter the amount of rainwater reaching the surface. However, stormwater management models generally treat all forest structures (beyond needle versus broadleaved) similarly. This study examines the rainfall partitioning of Pinus spp. canopies along a natural-to-urban forest gradient and compares these to canopy structural measurements using terrestrial LiDAR. Throughfall and meteorological observations were also used to estimate parameters of the commonly-used Gash interception model. Preliminary findings indicate that as forest structure changed from natural, closed canopy conditions to semi-closed canopy fragments and, ultimately, to exposed urban landscaping tree rows, the interchange between throughfall and rainfall interception also changed. This shift in partitioning between throughfall and rainfall interception may be linked to intuitive parameters, like canopy closure and density, as well as more complex metrics, like the fine-scale patterning of gaps (ie, lacunarity). Thus, results indicate that not all forests of the same species should be treated the same by stormwater models. Rather, their canopy structural characteristics should be used to vary their hydrometeorological interactions.

Impact of aerodynamic resistance formulations used in two-source modeling of energy exchange from the soil and vegetation using land surface temperature

USDA-ARS?s Scientific Manuscript database

Application of the Two-Source Energy Balance (TSEB) Model using land surface temperature (LST) requires aerodynamic resistance parameterizations for the flux exchange above the canopy layer, within the canopy air space and at the soil/substrate surface. There are a number of aerodynamic resistance f...

Evaluation of an urban vegetative canopy scheme and impact on plume dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, Matthew A; Williams, Michael D; Zajic, Dragan

2009-01-01

The Quick Urban and Industrial Complex (QUIC) atmospheric dispersion modeling system attempts to fill an important gap between the fast, but nonbuilding-aware Gaussian plume models and the building-aware but slow computational fluid dynamics (CFD) models. While Gaussian models have the ability to give answers quickly to emergency responders, they are unlikely to be able to adequately account for the effects of the building-induced complex flow patterns on the near-source dispersion of contaminants. QUIC uses a diagnostic massconsistent empirical wind model called QUIC-URB that is based on the methodology of Rockle (1990), (see also Kaplan and Dinar 1996). In this approach,more » the recirculation zones that form around and between buildings are inserted into the flow using empirical parameterizations and then the wind field is forced to be mass consistent. Although not as accurate as CFD codes, this approach is several orders of magnitude faster and accounts for the bulk effects of buildings.« less

Identifying the environmental factors that effect within canopy BVOC loss using a multilevel canopy model

NASA Astrophysics Data System (ADS)

Chan, W. S.; Fuentes, J. D.; Lerdau, M.

2010-12-01

This presentation will provide research findings to evaluate the hypothesis that the loss of biogenic volatile organic compound (BVOC) within plant canopies is dynamic and depends on factors such as plant canopy architecture (height and leaf area distribution), atmospheric turbulence, concentration of oxidants (OH, O3, NO3), and the reactivity of BVOC species. Results will be presented from a new one dimensional, multilevel canopy model that couples algorithms for canopy microclimate, leaf physiology, BVOC emission, turbulent transport, and atmospheric chemistry to investigate the relative importance of factors that impact BVOC loss within a forest canopy. Model sensitivity tests will be presented and discussed to identify factors driving canopy loss. Results show isoprene and monoterpene canopy losses as high as 9 and 18%, respectively, for tall canopies during the daytime. We hypothesize that canopy height and wind speed (i.e. canopy residence time) may be the most important in dictating within-canopy loss. This work will reduce the error in bottom-up flux estimates of BVOCs and ultimately improve parameterizations of BVOC sources in air quality models by accounting for within canopy processes.

Contribution and loading estimation of organochlorine pesticides from rain and canopy throughfall to runoff in an urban environment.

PubMed

Zhang, Wei; Ye, Youbin; Tong, Yindong; Ou, Langbo; Hu, Dan; Wang, Xuejun

2011-01-30

Concentrations of OCPs in rain, canopy throughfall, and runoff water were measured in the Beijing metropolitan area during the rainy seasons from 2006 to 2007. This study was conducted to calculate the fluxes of OCPs in rain and canopy throughfall, as well as their contributions to runoff. At urban sites, the contribution of HCB and ΣHCHs from rainfall accounted for approximately 50% of the mass in runoff. At the site with significant coverage of landscaping trees, the HCB, ΣHCHs, and ΣDDTs from the net canopy throughfall accounted for approximately 10% of the mass in the runoff. Based on the data obtained in this study, loadings of OCPs (in μg) in rain, net canopy throughfall, and runoff water were calculated. The input of OCPs from rain and canopy throughfall water accounted for a significant portion of urban runoff. In cities undergoing rapid urban sprawl, monitoring and control of the transport of OCPs in urban runoff are essential for effective control of environmental hazards in surface water bodies. Copyright © 2010 Elsevier B.V. All rights reserved.

Applications of urban tree canopy assessment and prioritization tools: supporting collaborative decision making to achieve urban sustainability goals

Treesearch

Dexter H. Locke; J. Morgan Grove; Michael Galvin; Jarlath P.M. ONeil-Dunne; Charles Murphy

2013-01-01

Urban Tree Canopy (UTC) Prioritizations can be both a set of geographic analysis tools and a planning process for collaborative decision-making. In this paper, we describe how UTC Prioritizations can be used as a planning process to provide decision support to multiple government agencies, civic groups and private businesses to aid in reaching a canopy target. Linkages...

Investigating the Potential of Land Use Modifications to Mitigate the Respiratory Health Impacts of NO2: A Case Study in the Portland-Vancouver Metropolitan Area

NASA Astrophysics Data System (ADS)

Rao, Meenakshi

The health impacts of urban air pollution are a growing concern in our rapidly urbanizing world. Urban air pollutants show high intra-urban spatial variability linked to urban land use and land cover (LULC). This correlation of air pollutants with LULC is widely recognized; LULC data is an integral input into a wide range of models, especially land use regression models developed by epidemiologists to study the impact of air pollution on human health. Given the demonstrated links between LULC and urban air pollution, and between urban air pollution and health, an interesting question arises: what is the potential of LULC modifications to mitigate the health impacts of urban air pollution? In this dissertation we assess the potential of LULC modifications to mitigate the health impacts of NO2, a respiratory irritant and strong marker for combustion-related air pollution, in the Portland-Vancouver metropolitan area in northwestern USA. We begin by measuring summer and winter NO2 in the area using a spatially dense network of passive NO 2 samplers. We next develop an annual average model for NO2 based on the observational data, using random forest--for the first time in the realm of urban air pollution--to disentangle the effects of highly correlated LULC variables on ambient NO2 concentrations. We apply this random forest (LURF) model to a 200m spatial grid covering the study area, and use this 200m LURF model to quantify the effect of different urban land use categories on ambient concentrations of NO2. Using the changes in ambient NO2 concentrations resulting from land use modifications as input to BenMAP (a health benefits assessment tool form the US EPA), we assess the NO2-related health impact associated with each land use category and its modifications. We demonstrate how the LURF model can be used to assess the respiratory health benefits of competing land use modifications, including city-wide and local-scale mitigation strategies based on modifying tree canopy and vehicle miles traveled (VMT). Planting trees is a common land cover modification strategy undertaken by cities to reduce air pollution. Statistical models such as LUR and LURF demonstrate a correlation between tree cover and reduced air pollution, but they cannot demonstrate causation. Hence, we run the atmospheric chemistry and transport model CMAQ to examine to what extent the dry deposition mechanism can explain the reduction of NO2 which statistical models associate with tree canopy. Results from our research indicate that even though the Portland-Vancouver area is in compliance with the US EPA NO2 standards, ambient concentrations of NO2 still create an annual health burden of at least 40 million USD. Our model suggests that NO2 associated with high intensity development and VMT may be creating an annual health burden of 7 million and 3.3 million USD respectively. Existing tree canopy, on the other hand, is associated with an annual health benefit of 1.4 million USD. LULC modifications can mitigate some fraction of this health burden. A 2% increase in tree canopy across the study area may reduce incidence rates of asthma exacerbation by as much as 7%. We also find that increasing tree canopy is a more effective strategy than reducing VMT in terms of mitigating the health burden of NO 2. CMAQ indicates that the amount of NO2 removed by dry deposition is an order of magnitude smaller than that predicted by our statistical model. About one-third of the difference can be explained by the lower NO2 values predicted by CMAQ, and one-third may be attributable to parameterization of stomatal uptake.

Difficulties with estimating city-wide urban forest cover change from national, remotely-sensed tree canopy maps

Treesearch

Jeffrey T. Walton

2008-01-01

Two datasets of percent urban tree canopy cover were compared. The first dataset was based on a 1991 AVHRR forest density map. The second was the US Geological Survey's National Land Cover Database (NLCD) 2001 sub-pixel tree canopy. A comparison of these two tree canopy layers was conducted in 36 census designated places of western New York State. Reference data...

Parameterization of the ACRU model for estimating biophysical and climatological change impacts, Beaver Creek, Alberta

NASA Astrophysics Data System (ADS)

Forbes, K. A.; Kienzle, S. W.; Coburn, C. A.; Byrne, J. M.

2006-12-01

Multiple threats, including intensification of agricultural production, non-renewable resource extraction and climate change, are threatening Southern Alberta's water supply. The objective of this research is to calibrate/evaluate the Agricultural Catchments Research Unit (ACRU) agrohydrological model; with the end goal of forecasting the impacts of a changing environment on water quantity. The strength of this model is the intensive multi-layered soil water budgeting routine that integrates water movement between the surface and atmosphere. The ACRU model was parameterized using data from Environment Canada's climate database for a twenty year period (1984-2004) and was used to simulate streamflow for Beaver Creek. The simulated streamflow was compared to Environment Canada's historical streamflow database to validate the model output. The Beaver Creek Watershed, located in the Porcupine Hills southwestern Alberta, Canada contains a heterogeneous cover of deciduous, coniferous, native prairie grasslands and forage crops. In a catchment with highly diversified land cover, canopy architecture cannot be overlooked in rainfall interception parameterization. Preliminary testing of ACRU suggests that streamflows were sensitive to varied levels of leaf area index (LAI), a representative fraction of canopy foliage. Further testing using remotely sensed LAI's will provide a more accurate representation of canopy foliage and ultimately best represent this important element of the hydrological cycle and the associated processes which govern the natural hydrology of the Beaver Creek watershed.

Mean and turbulent flow statistics in a trellised agricultural canopy

USDA-ARS?s Scientific Manuscript database

The architecture of a trellised agricultural canopy presents many similarities to homogeneous plant canopies, windbreaks, and urban canopies including street canyons. Compared to these other canopies, trellised canopies (e.g. vineyard) present an interesting, complex, two-dimensional environment tha...

Forest Canopy Processes in a Regional Chemical Transport Model

NASA Astrophysics Data System (ADS)

Makar, Paul; Staebler, Ralf; Akingunola, Ayodeji; Zhang, Junhua; McLinden, Chris; Kharol, Shailesh; Moran, Michael; Robichaud, Alain; Zhang, Leiming; Stroud, Craig; Pabla, Balbir; Cheung, Philip

2016-04-01

Forest canopies have typically been absent or highly parameterized in regional chemical transport models. Some forest-related processes are often considered - for example, biogenic emissions from the forests are included as a flux lower boundary condition on vertical diffusion, as is deposition to vegetation. However, real forest canopies comprise a much more complicated set of processes, at scales below the "transport model-resolved scale" of vertical levels usually employed in regional transport models. Advective and diffusive transport within the forest canopy typically scale with the height of the canopy, and the former process tends to dominate over the latter. Emissions of biogenic hydrocarbons arise from the foliage, which may be located tens of metres above the surface, while emissions of biogenic nitric oxide from decaying plant matter are located at the surface - in contrast to the surface flux boundary condition usually employed in chemical transport models. Deposition, similarly, is usually parameterized as a flux boundary condition, but may be differentiated between fluxes to vegetation and fluxes to the surface when the canopy scale is considered. The chemical environment also changes within forest canopies: shading, temperature, and relativity humidity changes with height within the canopy may influence chemical reaction rates. These processes have been observed in a host of measurement studies, and have been simulated using site-specific one-dimensional forest canopy models. Their influence on regional scale chemistry has been unknown, until now. In this work, we describe the results of the first attempt to include complex canopy processes within a regional chemical transport model (GEM-MACH). The original model core was subdivided into "canopy" and "non-canopy" subdomains. In the former, three additional near-surface layers based on spatially and seasonally varying satellite-derived canopy height and leaf area index were added to the original model structure. Process methodology for deposition, biogenic emissions, shading, vertical diffusion, advection, chemical reactive environment and particle microphysics were modified to account for expected conditions within the forest canopy and the additional layers. The revised and original models were compared for a 10km resolution domain covering North America, for a one-month duration simulation. The canopy processes were found to have a very significant impact on model results. We will present a comparison to network observations which suggests that forest canopy processes may account for previously unexplained local and regional biases in model ozone predictions noted in GEM-MACH and other models. The impact of the canopy processes on NO2, PM2.5, and SO2 performance will also be presented and discussed.

Fluxes of ozone and Biogenic Volatile Organic Compounds in a mixed Mediterranean forest over a transition period between summer and fall

NASA Astrophysics Data System (ADS)

Fares, S.; Schnitzhofer, R.; Hansel, A.; Petersson, F.; Matteucci, G.; Scarascia Mugnozza, G.; Jiang, X.; Guenther, A. B.; Loreto, F.

2012-12-01

Mediterranean plant ecosystems are exposed to abiotic stressors that may be exacerbated by climate change dynamics. Moreover, plants need now to cope with increasing anthropogenic pressures, often associated with expanding impacts of urbanization. Anthropogenic stressors include harmful gases (e.g. ozone,) that are transported from anthropogenic pollution sources to the vegetation. They may alter ecophysiology and compromise metabolism of Mediterranean plants. A disproportionate number of Mediterranean ecosystems, many dominated by forest trees, are being transformed into "urban or pre-urban forests". This is in particular the case for Castelporziano Estate, a 6,000 ha Mediterranean forest located just 25 km from Rome downtown at the coast of the Mediterranean Sea. In September 2011 an intensive field campaign was performed in Castelporziano to investigate ozone deposition and biogenic emissions of volatile organic compounds (BVOC) from a mixed Mediterranean forest, mainly composed by Quercus suber, Quercus ilex, Pinus pinea. Measurements were performed at canopy level with fast real-time instruments (a fast ozone analyzer and a Proton Transfer Reaction-Time of Flight Mass Spectrometer) that allowed eddy covariant flux measurements of ozone and BVOC. In the transitional period from a warm and dry summer to a wet and moderately cool fall we typically observed tropospheric ozone volume mixing ratios (VMR) of 60 ppb at around noon, with high deposition fluxes (up to -10 nmol m-2 s-1) into the forest canopy. Canopy models were used to to calculate that up to 90% of ozone uptake can be attributed to non-stomatal sinks, suggesting that chemical reactions between ozone and reactive BVOC may have played an important role. The concentrations of reactive isoprenoids (e.g. sesquiterpenes) were indeed observed to decrease during the central hours of the day, in coincidence with increased ozone concentrations. Concentrations and fluxes of isoprenoid-ozone-oxidation-(methyl-vinyl-ketone and methacrolein) were found to increase during the day time hours, matching the dynamic pattern of non-stomatal ozone uptake. Monoterpenes were the most abundant BVOC emitted by the forest with fluxes up to 10 nmol m-2 s-1 in the warm days, followed by the oxygenated BVOCs: methanol, acetone, acetaldehyde. Isoprene was emitted at a low rate (less than 1 nmol m-2 s-1), and observations used to develop a new parameterization data for modelling activity. MEGAN was used to predict biogenic emissions from Mediterranean ecosystems. Model results using new basal emission factors (BEF) estimated from the collected data-set revealed considerable differences in the emission estimates compared with the standard parameterization, thus suggesting the importance of including basal emission factors from monoterpene-emitting Mediterranean ecosystems to obtain an accurate estimate in the global model. Future research by chemical transport modelling and smog chamber experiments are planned to investigate the "ex-situ" ozone-forming potential of emitted BVOC, to fully understand the role of Mediterranean urban forests in the complex interactions between biosphere and atmosphere over large Mediterranean conurbations.

Coupled carbon-water exchange of the Amazon rain forest, I. Model description, parameterization and sensitivity analysis

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Ganzeveld, L.; Kesselmeier, J.

2005-04-01

Detailed one-dimensional multilayer biosphere-atmosphere models, also referred to as CANVEG models, are used for more than a decade to describe coupled water-carbon exchange between the terrestrial vegetation and the lower atmosphere. Within the present study, a modified CANVEG scheme is described. A generic parameterization and characterization of biophysical properties of Amazon rain forest canopies is inferred using available field measurements of canopy structure, in-canopy profiles of horizontal wind speed and radiation, canopy albedo, soil heat flux and soil respiration, photosynthetic capacity and leaf nitrogen as well as leaf level enclosure measurements made on sunlit and shaded branches of several Amazonian tree species during the wet and dry season. The sensitivity of calculated canopy energy and CO2 fluxes to the uncertainty of individual parameter values is assessed. In the companion paper, the predicted seasonal exchange of energy, CO2, ozone and isoprene is compared to observations.

A bi-modal distribution of leaf area density with a total leaf area index of 6 is inferred from several observations in Amazonia. Predicted light attenuation within the canopy agrees reasonably well with observations made at different field sites. A comparison of predicted and observed canopy albedo shows a high model sensitivity to the leaf optical parameters for near-infrared short-wave radiation (NIR). The predictions agree much better with observations when the leaf reflectance and transmission coefficients for NIR are reduced by 25-40%. Available vertical distributions of photosynthetic capacity and leaf nitrogen concentration suggest a low but significant light acclimation of the rain forest canopy that scales nearly linearly with accumulated leaf area.

Evaluation of the biochemical leaf model, using the enclosure measurements, showed that recommended parameter values describing the photosynthetic light response, have to be optimized. Otherwise, predicted net assimilation is overestimated by 30-50%. Two stomatal models have been tested, which apply a well established semi-empirical relationship between stomatal conductance and net assimilation. Both models differ in the way they describe the influence of humidity on stomatal response. However, they show a very similar performance within the range of observed environmental conditions. The agreement between predicted and observed stomatal conductance rates is reasonable. In general, the leaf level data suggests seasonal physiological changes, which can be reproduced reasonably well by assuming increased stomatal conductance rates during the wet season, and decreased assimilation rates during the dry season.

The sensitivity of the predicted canopy fluxes of energy and CO2 to the parameterization of canopy structure, the leaf optical parameters, and the scaling of photosynthetic parameters is relatively low (1-12%), with respect to parameter uncertainty. In contrast, modifying leaf model parameters within their uncertainty range results in much larger changes of the predicted canopy net fluxes (5-35%).

Coupled carbon-water exchange of the Amazon rain forest, I. Model description, parameterization and sensitivity analysis

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Ganzeveld, L.; Kesselmeier, J.

2005-09-01

Detailed one-dimensional multilayer biosphere-atmosphere models, also referred to as CANVEG models, are used for more than a decade to describe coupled water-carbon exchange between the terrestrial vegetation and the lower atmosphere. Within the present study, a modified CANVEG scheme is described. A generic parameterization and characterization of biophysical properties of Amazon rain forest canopies is inferred using available field measurements of canopy structure, in-canopy profiles of horizontal wind speed and radiation, canopy albedo, soil heat flux and soil respiration, photosynthetic capacity and leaf nitrogen as well as leaf level enclosure measurements made on sunlit and shaded branches of several Amazonian tree species during the wet and dry season. The sensitivity of calculated canopy energy and CO2 fluxes to the uncertainty of individual parameter values is assessed. In the companion paper, the predicted seasonal exchange of energy, CO2, ozone and isoprene is compared to observations.

A bi-modal distribution of leaf area density with a total leaf area index of 6 is inferred from several observations in Amazonia. Predicted light attenuation within the canopy agrees reasonably well with observations made at different field sites. A comparison of predicted and observed canopy albedo shows a high model sensitivity to the leaf optical parameters for near-infrared short-wave radiation (NIR). The predictions agree much better with observations when the leaf reflectance and transmission coefficients for NIR are reduced by 25-40%. Available vertical distributions of photosynthetic capacity and leaf nitrogen concentration suggest a low but significant light acclimation of the rain forest canopy that scales nearly linearly with accumulated leaf area.

Evaluation of the biochemical leaf model, using the enclosure measurements, showed that recommended parameter values describing the photosynthetic light response, have to be optimized. Otherwise, predicted net assimilation is overestimated by 30-50%. Two stomatal models have been tested, which apply a well established semi-empirical relationship between stomatal conductance and net assimilation. Both models differ in the way they describe the influence of humidity on stomatal response. However, they show a very similar performance within the range of observed environmental conditions. The agreement between predicted and observed stomatal conductance rates is reasonable. In general, the leaf level data suggests seasonal physiological changes, which can be reproduced reasonably well by assuming increased stomatal conductance rates during the wet season, and decreased assimilation rates during the dry season.

The sensitivity of the predicted canopy fluxes of energy and CO2 to the parameterization of canopy structure, the leaf optical parameters, and the scaling of photosynthetic parameters is relatively low (1-12%), with respect to parameter uncertainty. In contrast, modifying leaf model parameters within their uncertainty range results in much larger changes of the predicted canopy net fluxes (5-35%).

Watershed Land Use and Seasonal Variation Constrain the ...

EPA Pesticide Factsheets

While watershed and local scale controls on stream metabolism have been independently investigated, little is known about how controls exerted at these different scales interact to determine stream metabolic rates, or how these interactions vary across seasons. To address this knowledge gap, we measured ecosystem metabolism in four urban and four reference streams in northern Kentucky, USA, with paired closed and open riparian canopies, during each of the four seasons of the year. Gross primary production (GPP), ecosystem respiration (ER), and net ecosystem production (NEP) were all best predicted by models with season as a main effect, but interactions between season, canopy and watershed varied for each response. Urban streams exhibited higher GPP during most seasons, likely due to elevated nutrient loads. Open canopy reaches in both urban and forested streams supported higher rates of GPP than the closed canopy reaches during the summer and fall when the overhead vegetation shaded the closed reaches. Surprisingly, the effect of canopy cover on GPP was similar among urban and forested streams. The combination of watershed and local-scale controls resulted in urban streams that alternated between net heterotrophy (NEP 0) between seasons with and without dense canopy cover. This finding has management relevance because net production can lead to accumulation of algal biomass and associated issues like dissolved oxygen sags at night. Our study reinforces

Effects of urban tree canopy loss on land surface temperature magnitude and timing

Treesearch

Arthur Elmes; John Rogan; Christopher Williams; Samuel Ratick; David Nowak; Deborah Martin

2017-01-01

Urban Tree Canopy (UTC) plays an important role in moderating the Surface Urban Heat Island (SUHI) effect, which poses threats to human health due to substantially increased temperatures relative to rural areas. UTC coverage is associated with reduced urban temperatures, and therefore benefits both human health and reducing energy use in cities. Measurement of this...

Tree canopy change and neighborhood stability: A comparative analysis of Washington, D.C. and Baltimore, MD

Treesearch

Wen-Ching Chuang; Christopher G. Boone; Dexter H. Locke; J. Morgan Grove; Ali Whitmer; Geoffrey Buckley; Sainan Zhang

2017-01-01

Trees provide important health, ecosystem, and aesthetic services in urban areas, but they are unevenly distributed. Some neighborhoods have abundant tree canopy and others nearly none. We analyzed how neighborhood characteristics and changes in income over time related to the distribution of urban tree canopy in Washington, D.C. and Baltimore, MD. We used stepwise...

What's scale got to do with it? Models for urban tree canopy

Treesearch

Dexter H. Locke; Shawn M. Landry; Morgan Grove; Rinku Roy Chowdhury

2016-01-01

The uneven provisioning of ecosystem services has important policy implications; yet the spatial heterogeneity of tree canopy remains understudied. Private residential lands are important to the future of Philadelphia’s urban forest because a majority of the existing and possible tree canopy is located on residential land uses. This article examines the spatial...

Effect of canopy and topography induced wakes on land-atmosphere fluxes of momentum and scalars

NASA Astrophysics Data System (ADS)

Markfort, C. D.; Zhang, W.; Porté-Agel, F.; Stefan, H. G.

2012-04-01

Wakes shed from natural and anthropogenic landscape features affect land-atmosphere fluxes of momentum and scalars, including water vapor and trace gases (e.g. CO2). Canopies and bluff bodies, such as forests, buildings and topography, cause boundary layer flow separation, and lead to a break down of standard Monin-Obukhov similarity relationships in the atmospheric boundary layer (ABL). Wakes generated by these land surface features persist for significant distances (>100 typical length scales) and affect a large fraction of the Earth's terrestrial surface. This effect is currently not accounted for in land-atmosphere models, and little is known about how heterogeneity of wake-generating features affect land surface fluxes. Additionally flux measurements, made in wake-affected regions, do not satisfy the homogeneous flow requirements for the standard eddy correlation (EC) method. This phenomenon, often referred to as wind sheltering, has been shown to affect momentum and kinetic energy fluxes at the lake-atmosphere interface (Markfort et al. 2010). This presentation will highlight results from controlled wind tunnel experiments of neutral and thermally stratified boundary layers, using particle image velocimetry (PIV) and custom x-wire/cold-wire anemometry, to understand how the physical structure of upstream bluff bodies and porous canopies as well as how thermal stability affect the flow separation zone, boundary layer recovery and surface fluxes. We have found that there is a nonlinear relationship between canopy length/porosity and flow separation downwind of a canopy to clearing transition. Results will provide the basis for new parameterizations to account for wake effects on land-atmosphere fluxes and corrections for the EC measurements over open fields, lakes, and wetlands. Key words: Atmospheric boundary layer; Wakes; Stratification; Land-Atmosphere Parameterization; Canopy

Case study: Rainfall partitioning across a natural-to-urban forest gradient during an extreme rain event

NASA Astrophysics Data System (ADS)

Akin, B. H.; Van Stan, J. T., II; Cote, J. F.; Jarvis, M. T.; Underwood, J.; Friesen, J.; Hildebrandt, A.; Maldonado, G.

2017-12-01

Trees' partitioning of rainfall is an important first process along the rainfall-to-runoff pathway that has economically significant influences on urban stormwater management. However, important knowledge gaps exist regarding (1) its role during extreme storms and (2) how this role changes as forest structure is altered by urbanization. Little research has been conducted on canopy rainfall partitioning during large, intense storms, likely because canopy water storage is rapidly overwhelmed (i.e., 1-3 mm) by short duration events exceeding, for example, 80 mm of rainfall. However, canopy structure controls more than just storage; it also affects the time for rain to drain to the surface (becoming throughfall) and the micrometeorological conditions that drive wet canopy evaporation. In fact, observations from an example extreme ( 100 mm with maximum 5-minute intensities exceeding 55 mm/h) storm across a urban-to-natural gradient in pine forests in southeast Georgia (USA), show that storm intensities were differentially dampened by 33% (tree row), 28% (forest fragment), and 17% (natural forests). In addition, maximum wet canopy evaporation rates were higher for the exposed tree row (0.18 mm/h) than for the partially-enclosed fragment canopy (0.14 mm/h) and the closed canopy natural forest site (0.11). This resulted in interception percentages decreasing from urban-to-natural stand structures (25% to 16%). A synoptic analysis of the extreme storm in this case study also shows that the mesoscale meteorological conditions that developed the heavy rainfall is expected to occur more often with projected climate changes.

A new stomatal paradigm for earth system models? (Invited)

NASA Astrophysics Data System (ADS)

Bonan, G. B.; Williams, M. D.; Fisher, R. A.; Oleson, K. W.; Lombardozzi, D.

2013-12-01

The land component of climate, and now earth system, models has simulated stomatal conductance since the introduction in the mid-1980s of the so-called second generation models that explicitly represented plant canopies. These second generation models used the Jarvis-style stomatal conductance model, which empirically relates stomatal conductance to photosynthetically active radiation, temperature, vapor pressure deficit, CO2 concentration, and other factors. Subsequent models of stomatal conductance were developed from a more mechanistic understanding of stomatal physiology, particularly that stomata are regulated so as to maximize net CO2 assimilation (An) and minimize water loss during transpiration (E). This concept is embodied in the Ball-Berry stomatal conductance model, which relates stomatal conductance (gs) to net assimilation (An), scaled by the ratio of leaf surface relative humidity to leaf surface CO2 concentration, or the Leuning variant which replaces relative humidity with a vapor pressure deficit term. This coupled gs-An model has been widely used in climate and earth system models since the mid-1990s. An alternative approach models stomatal conductance by directly optimizing water use efficiency, defined as the ratio An/gs or An/E. Conceptual developments over the past several years have shown that the Ball-Berry style model can be derived from optimization theory. However, an explicit optimization model has not been tested in an earth system model. We compare the Ball-Berry model with an explicit optimization model, both implemented in a new plant canopy parameterization developed for the Community Land Model, the land component of the Community Earth System Model. The optimization model is from the Soil-Plant-Atmosphere (SPA) model, which integrates plant and soil hydraulics, carbon assimilation, and gas diffusion. The canopy parameterization is multi-layer and resolves profiles of radiation, temperature, vapor pressure, leaf water stress, stomatal conductance, and photosynthetic capacity within the canopy. Stomatal conductance for each layer is calculated so as to maximize carbon gain, within the limitations of plant water storage and soil-to-canopy water transport. An iterative procedure determines for every model timestep the maximum stomatal conductance for a canopy layer and the associated assimilation rate. We compare the Ball-Berry stomatal model and the SPA stomatal model within the multi-layer canopy parameterization. We use eddy covariance flux tower data for six sites (three deciduous broadleaf forest and three evergreen needleleaf forest) spanning a total of 51 site-years. The multi-layer canopy has improved simulation of gross primary production (GPP), evapotranspiration, and sensible heat flux compared with the most recent version of the Community Land Model (CLM4.5). The Ball-Berry and SPA stomatal models have prominent differences in simulated fluxes and compared with observations. This is most evident during drought.

Comparative assessment of methods for estimating tree canopy cover across a rural-to-urban gradient in the mid-Atlantic region of the USA

Treesearch

Rachel Riemann; Greg C. Liknes; Jarlath O' Neil-Dunne; Chris Toney; Tonya Lister

2016-01-01

Tree canopy cover significantly affects human and wildlife habitats, local hydrology, carbon cycles, fire behavior, and ecosystem services of all types. In addition, changes in tree canopy cover are both indicators and consequences of a wide variety of disturbances from urban development to climate change. There is growing demand for this information nationwide and...

Mapping Urban Tree Canopy Cover Using Fused Airborne LIDAR and Satellite Imagery Data

NASA Astrophysics Data System (ADS)

Parmehr, Ebadat G.; Amati, Marco; Fraser, Clive S.

2016-06-01

Urban green spaces, particularly urban trees, play a key role in enhancing the liveability of cities. The availability of accurate and up-to-date maps of tree canopy cover is important for sustainable development of urban green spaces. LiDAR point clouds are widely used for the mapping of buildings and trees, and several LiDAR point cloud classification techniques have been proposed for automatic mapping. However, the effectiveness of point cloud classification techniques for automated tree extraction from LiDAR data can be impacted to the point of failure by the complexity of tree canopy shapes in urban areas. Multispectral imagery, which provides complementary information to LiDAR data, can improve point cloud classification quality. This paper proposes a reliable method for the extraction of tree canopy cover from fused LiDAR point cloud and multispectral satellite imagery data. The proposed method initially associates each LiDAR point with spectral information from the co-registered satellite imagery data. It calculates the normalised difference vegetation index (NDVI) value for each LiDAR point and corrects tree points which have been misclassified as buildings. Then, region growing of tree points, taking the NDVI value into account, is applied. Finally, the LiDAR points classified as tree points are utilised to generate a canopy cover map. The performance of the proposed tree canopy cover mapping method is experimentally evaluated on a data set of airborne LiDAR and WorldView 2 imagery covering a suburb in Melbourne, Australia.

Building capacity for providing canopy cover and canopy height at FIA plot locations using high-resolution imagery and leaf-off LiDAR

Treesearch

Rachel Riemann; Jarlath O' Neil-Dunne; Greg C. Liknes

2012-01-01

Tree canopy cover and canopy height information are essential for estimating volume, biomass, and carbon; defining forest cover; and characterizing wildlife habitat. The amount of tree canopy cover also influences water quality and quantity in both rural and urban settings. Tree canopy cover and canopy height are currently collected at FIA plots either in the field or...

Monitoring urban tree cover using object-based image analysis and public domain remotely sensed data

Treesearch

L. Monika Moskal; Diane M. Styers; Meghan Halabisky

2011-01-01

Urban forest ecosystems provide a range of social and ecological services, but due to the heterogeneity of these canopies their spatial extent is difficult to quantify and monitor. Traditional per-pixel classification methods have been used to map urban canopies, however, such techniques are not generally appropriate for assessing these highly variable landscapes....

Towards Linking 3D SAR and Lidar Models with a Spatially Explicit Individual Based Forest Model

NASA Astrophysics Data System (ADS)

Osmanoglu, B.; Ranson, J.; Sun, G.; Armstrong, A. H.; Fischer, R.; Huth, A.

2017-12-01

In this study, we present a parameterization of the FORMIND individual-based gap model (IBGM)for old growth Atlantic lowland rainforest in La Selva, Costa Rica for the purpose of informing multisensor remote sensing techniques for above ground biomass techniques. The model was successfully parameterized and calibrated for the study site; results show that the simulated forest reproduces the structural complexity of Costa Rican rainforest based on comparisons with CARBONO inventory plot data. Though the simulated stem numbers (378) slightly underestimated the plot data (418), particularly for canopy dominant intermediate shade tolerant trees and shade tolerant understory trees, overall there was a 9.7% difference. Aboveground biomass (kg/ha) showed a 0.1% difference between the simulated forest and inventory plot dataset. The Costa Rica FORMIND simulation was then used to parameterize a spatially explicit (3D) SAR and lidar backscatter models. The simulated forest stands were used to generate a Look Up Table as a tractable means to estimate aboveground forest biomass for these complex forests. Various combinations of lidar and radar variables were evaluated in the LUT inversion. To test the capability of future data for estimation of forest height and biomass, we considered data of 1) L- (or P-) band polarimetric data (backscattering coefficients of HH, HV and VV); 2) L-band dual-pol repeat-pass InSAR data (HH/HV backscattering coefficients and coherences, height of scattering phase center at HH and HV using DEM or surface height from lidar data as reference); 3) P-band polarimetric InSAR data (canopy height from inversion of PolInSAR data or use the coherences and height of scattering phase center at HH, HV and VV); 4) various height indices from waveform lidar data); and 5) surface and canopy top height from photon-counting lidar data. The methods for parameterizing the remote sensing models with the IBGM and developing Look Up Tables will be discussed. Results from various remote sensing scenarios will also be presented.

ALAMEDA, a Structural–Functional Model for Faba Bean Crops: Morphological Parameterization and Verification

PubMed Central

RUIZ-RAMOS, MARGARITA; MÍNGUEZ, M. INÉS

2006-01-01

• Background Plant structural (i.e. architectural) models explicitly describe plant morphology by providing detailed descriptions of the display of leaf and stem surfaces within heterogeneous canopies and thus provide the opportunity for modelling the functioning of plant organs in their microenvironments. The outcome is a class of structural–functional crop models that combines advantages of current structural and process approaches to crop modelling. ALAMEDA is such a model. • Methods The formalism of Lindenmayer systems (L-systems) was chosen for the development of a structural model of the faba bean canopy, providing both numerical and dynamic graphical outputs. It was parameterized according to the results obtained through detailed morphological and phenological descriptions that capture the detailed geometry and topology of the crop. The analysis distinguishes between relationships of general application for all sowing dates and stem ranks and others valid only for all stems of a single crop cycle. • Results and Conclusions The results reveal that in faba bean, structural parameterization valid for the entire plant may be drawn from a single stem. ALAMEDA was formed by linking the structural model to the growth model ‘Simulation d'Allongement des Feuilles’ (SAF) with the ability to simulate approx. 3500 crop organs and components of a group of nine plants. Model performance was verified for organ length, plant height and leaf area. The L-system formalism was able to capture the complex architecture of canopy leaf area of this indeterminate crop and, with the growth relationships, generate a 3D dynamic crop simulation. Future development and improvement of the model are discussed. PMID:16390842

Characteristics and transport of organochlorine pesticides in urban environment: air, dust, rain, canopy throughfall, and runoff.

PubMed

Zhang, Wei; Ye, Youbin; Hu, Dan; Ou, Langbo; Wang, Xuejun

2010-11-01

Characteristics and transport of organochlorine pesticides (OCPs) in urban multiple environments, including air, dust, rain, canopy throughfall, and runoff water, are explored in this study. Hexachlorocyclohexanes (HCHs) dominated in both air and rain water, and dichlorodiphenyltrichloroethane (DDT) related substances showed a higher affinity to dust. Relatively high concentrations of DDT and dichlorodiphenyldichloroethylene (DDE) in air, rain and dust imply that technical DDT in the environment has been degrading, and there may be unknown local or regional emission sources that contain DDTs in the study area. Source identification showed that DDTs in Beijing urban environments with a fresh signature may originate from the atmospheric transport from remote areas. The ratio of α-/γ-HCH in dust, rain, canopy throughfall and runoff were close to 1, indicating the possible use of lindane. OCPs in runoff were transported from various sources including rain, dust, and canopy throughfall. In runoff, DDTs and hexachlorobenzene (HCB) were mainly transported from dust, and HCHs were mainly from rain and canopy throughfall.

Application of WRF/Chem-MADRID and WRF/Polyphemus in Europe - Part 1: Model description and evaluation of meteorological predictions

NASA Astrophysics Data System (ADS)

Zhang, Y.; Sartelet, K.; Wu, S.-Y.; Seigneur, C.

2013-02-01

Comprehensive model evaluation and comparison of two 3-D air quality modeling systems (i.e. the Weather Research and Forecast model (WRF)/Polyphemus and WRF with chemistry and the Model of Aerosol Dynamics, Reaction, Ionization, and Dissolution (MADRID) (WRF/Chem-MADRID) are conducted over western Europe. Part 1 describes the background information for the model comparison and simulation design, as well as the application of WRF for January and July 2001 over triple-nested domains in western Europe at three horizontal grid resolutions: 0.5°, 0.125°, and 0.025°. Six simulated meteorological variables (i.e. temperature at 2 m (T2), specific humidity at 2 m (Q2), relative humidity at 2 m (RH2), wind speed at 10 m (WS10), wind direction at 10 m (WD10), and precipitation (Precip)) are evaluated using available observations in terms of spatial distribution, domainwide daily and site-specific hourly variations, and domainwide performance statistics. WRF demonstrates its capability in capturing diurnal/seasonal variations and spatial gradients of major meteorological variables. While the domainwide performance of T2, Q2, RH2, and WD10 at all three grid resolutions is satisfactory overall, large positive or negative biases occur in WS10 and Precip even at 0.025°. In addition, discrepancies between simulations and observations exist in T2, Q2, WS10, and Precip at mountain/high altitude sites and large urban center sites in both months, in particular, during snow events or thunderstorms. These results indicate the model's difficulty in capturing meteorological variables in complex terrain and subgrid-scale meteorological phenomena, due to inaccuracies in model initialization parameterization (e.g. lack of soil temperature and moisture nudging), limitations in the physical parameterizations of the planetary boundary layer (e.g. cloud microphysics, cumulus parameterizations, and ice nucleation treatments) as well as limitations in surface heat and moisture budget parameterizations (e.g. snow-related processes, subgrid-scale surface roughness elements, and urban canopy/heat island treatments and CO2 domes). While the use of finer grid resolutions of 0.125° and 0.025° shows some improvement for WS10, Precip, and some mesoscale events (e.g. strong forced convection and heavy precipitation), it does not significantly improve the overall statistical performance for all meteorological variables except for Precip. These results indicate a need to further improve the model representations of the above parameterizations at all scales.

Intra-Urban Variability in Elemental Carbon Deposition to Tree Canopies

NASA Astrophysics Data System (ADS)

Barrett, T. E.; Ponette-González, A.; Rindy, J. E.; Sheesley, R. J.

2017-12-01

Urban areas cover <1% of the earth's land surface, yet they represent globally significant sources of atmospheric elemental carbon (EC). A product of incomplete fossil fuel, biofuel, and biomass combustion, EC is a powerful climate-forcing agent and a significant component of fine particulate matter in urban atmospheres. Thus, understanding the factors that govern EC removal in urban areas could help mitigate climate change, while improving air quality for urban residents. EC particles can be removed from the atmosphere in precipitation (wet and fog deposition) or they can settle directly onto receptor surfaces (dry deposition). Only limited measurements indicate that EC deposition is higher in urban than in rural and remote regions. However, EC deposition likely exhibits considerable intra-urban variability, with tree canopies serving as potentially important sinks for EC on the cityscape. The goal of this research is to quantify spatial variability in total (wet + dry) EC deposition to urban tree canopies in the Dallas-Fort Worth Metroplex. Using a stratified non-random sampling design, 41 oak trees (22 post oak (Quercus stellata) and 19 live oak (Quercus virginiana)) were selected near (<100 m) and far from roads (>100 m) for measurements of throughfall (water that falls from the canopy to the forest floor). Additionally, 16 bulk rainfall samplers were deployed in grassy areas with no canopy cover. Results from one rain event indicate a volume weighted mean concentration of 83 µg EC L-1 in post oak throughfall, 36 µg EC L-1 in live oak throughfall, and 4 µg EC L-1 in bulk rainfall. Total EC deposition to oak tree canopies was 2.0 ± 2.1 (SD) mg m-2 for post oak and 0.7 ± 0.3 mg m-2 for live oak. Bulk rainfall deposition was 0.08 ± 0.1 mg m-2. Our preliminary findings show that trees are effective urban air filters, removing 9-25 times more EC from the atmosphere than rainwater alone. Resolving surface controls on atmospheric EC removal is key to developing and assessing near-term climate and air quality mitigation strategies.

Growing Canopy on a College Campus: Understanding Urban Forest Change through Archival Records and Aerial Photography.

PubMed

Roman, Lara A; Fristensky, Jason P; Eisenman, Theodore S; Greenfield, Eric J; Lundgren, Robert E; Cerwinka, Chloe E; Hewitt, David A; Welsh, Caitlin C

2017-12-01

Many municipalities are setting ambitious tree canopy cover goals to increase the extent of their urban forests. A historical perspective on urban forest development can help cities strategize how to establish and achieve appropriate tree cover targets. To understand how long-term urban forest change occurs, we examined the history of trees on an urban college campus: the University of Pennsylvania in Philadelphia, PA. Using a mixed methods approach, including qualitative assessments of archival records (1870-2017), complemented by quantitative analysis of tree cover from aerial imagery (1970-2012), our analysis revealed drastic canopy cover increase in the late 20th and early 21st centuries along with the principle mechanisms of that change. We organized the historical narrative into periods reflecting campus planting actions and management approaches; these periods are also connected to broader urban greening and city planning movements, such as City Beautiful and urban sustainability. University faculty in botany, landscape architecture, and urban design contributed to the design of campus green spaces, developed comprehensive landscape plans, and advocated for campus trees. A 1977 Landscape Development Plan was particularly influential, setting forth design principles and planting recommendations that enabled the dramatic canopy cover gains we observed, and continue to guide landscape management today. Our results indicate that increasing urban tree cover requires generational time scales and systematic management coupled with a clear urban design vision and long-term commitments. With the campus as a microcosm of broader trends in urban forest development, we conclude with a discussion of implications for municipal tree cover planning.

The effect of urban growth on landscape-scale restoration for a fire-dependent songbird

USGS Publications Warehouse

Pickens, Bradley A.; Marcus, Jeffrey F.; Carpenter, John P.; Anderson, Scott; Taillie, Paul J.; Collazo, Jaime A.

2017-01-01

A landscape-scale perspective on restoration ecology has been advocated, but few studies have informed restoration with landscape metrics or addressed broad-scale threats. Threats such as urban growth may affect restoration effectiveness in a landscape context. Here, we studied longleaf pine savanna in the rapidly urbanizing southeastern United States where a habitat-specialist bird, Bachman's sparrow (Peucaea aestivalis), is closely associated with savanna vegetation structure and frequent fire. Our objectives were to construct a species distribution model for Bachman's sparrow, determine the relationship between fire and urbanization, quantify the urban growth effect (2010–2090), identify potential restoration areas, and determine the interaction between restoration potential and urban growth by 2050. Number of patches, patch size, and isolation metrics were used to evaluate scenarios. The species distribution model was 88% accurate and emphasized multiscale canopy cover characteristics, fire, and percent habitat. Fires were less common <600 m from urban areas, and this fire suppression effect exacerbated urban growth effects. For restoration scenarios, canopy cover reduction by 30% resulted in nearly double the amount of habitat compared to the prescribed fire scenario; canopy cover reduction resulted in larger patch sizes and less patch isolation compared to current conditions. The effect of urban growth on restoration scenarios was unequal. Seventy-four percent of restoration areas from the prescribed fire scenario overlapped with projected urban growth, whereas the canopy cover reduction scenario only overlapped by 9%. We emphasize the benefits of simultaneously considering the effects of urban growth and landscape-scale restoration potential to promote a landscape with greater patch sizes and less isolation.

Growing Canopy on a College Campus: Understanding Urban Forest Change through Archival Records and Aerial Photography

NASA Astrophysics Data System (ADS)

Roman, Lara A.; Fristensky, Jason P.; Eisenman, Theodore S.; Greenfield, Eric J.; Lundgren, Robert E.; Cerwinka, Chloe E.; Hewitt, David A.; Welsh, Caitlin C.

2017-12-01

Many municipalities are setting ambitious tree canopy cover goals to increase the extent of their urban forests. A historical perspective on urban forest development can help cities strategize how to establish and achieve appropriate tree cover targets. To understand how long-term urban forest change occurs, we examined the history of trees on an urban college campus: the University of Pennsylvania in Philadelphia, PA. Using a mixed methods approach, including qualitative assessments of archival records (1870-2017), complemented by quantitative analysis of tree cover from aerial imagery (1970-2012), our analysis revealed drastic canopy cover increase in the late 20th and early 21st centuries along with the principle mechanisms of that change. We organized the historical narrative into periods reflecting campus planting actions and management approaches; these periods are also connected to broader urban greening and city planning movements, such as City Beautiful and urban sustainability. University faculty in botany, landscape architecture, and urban design contributed to the design of campus green spaces, developed comprehensive landscape plans, and advocated for campus trees. A 1977 Landscape Development Plan was particularly influential, setting forth design principles and planting recommendations that enabled the dramatic canopy cover gains we observed, and continue to guide landscape management today. Our results indicate that increasing urban tree cover requires generational time scales and systematic management coupled with a clear urban design vision and long-term commitments. With the campus as a microcosm of broader trends in urban forest development, we conclude with a discussion of implications for municipal tree cover planning.

A canopy architectural model to study the competitive ability of chickpea with sowthistle.

PubMed

Cici, S-Zahra-Hosseini; Adkins, Steve; Hanan, Jim

2008-06-01

Improving the competitive ability of crops is a sustainable method of weed management. This paper shows how a virtual plant model of competition between chickpea (Cicer arietinum) and sowthistle (Sonchus oleraceus) can be used as a framework for discovering and/or developing more competitive chickpea cultivars. The virtual plant models were developed using the L-systems formalism, parameterized according to measurements taken on plants at intervals during their development. A quasi-Monte Carlo light-environment model was used to model the effect of chickpea canopy on the development of sowthistle. The chickpea-light environment-sowthistle model (CLES model) captured the hypothesis that the architecture of chickpea plants modifies the light environment inside the canopy and determines sowthistle growth and development pattern. The resulting CLES model was parameterized for different chickpea cultivars (viz. 'Macarena', 'Bumper', 'Jimbour' and '99071-1001') to compare their competitive ability with sowthistle. To validate the CLES model, an experiment was conducted using the same four chickpea cultivars as different treatments with a sowthistle growing under their canopy. The growth of sowthistle, both in silico and in glasshouse experiments, was reduced most by '99071-1001', a cultivar with a short phyllochron. The second rank of competitive ability belonged to 'Macarena' and 'Bumper', while 'Jimbour' was the least competitive cultivar. The architecture of virtual chickpea plants modified the light inside the canopy, which influenced the growth and development of the sowthistle plants in response to different cultivars. This is the first time that a virtual plant model of a crop-weed interaction has been developed. This virtual plant model can serve as a platform for a broad range of applications in the study of chickpea-weed interactions and their environment.

Quantifying interception associated with new urban vegetation canopies

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2013-12-01

Interception of precipitation by vegetation canopies has long been recognized as an important component of the hydrologic cycle, though most research has been in closed or sparse canopy forests. Much less work has been published on interception by urban vegetation, and especially associated with the low growing shrubs commonly installed in green infrastructure program. To inform urban watershed model with vegetation-specific interception data, a field experiment was designed to directly measure canopy throughfall associated with two shrub species commonly included in urban greening programs. Data was collected at a high (e.g. five second) sampling frequency. A non-parametric Kruskal-Wallis test performed on data collected between August and October of 2012 demonstrated statistically significant (p= 0.0011) differences in recorded throughfall between two species (94% for Itea virginica, 86% for Cornus sericea). Additionally, the results suggested that the relationship of throughfall to rainfall intensity varied by species. For Itea, the ratio of throughfall to precipitation intensity was close to 1:1. However, for Cornus, the throughfall rate was on average slower (or 0.85 of the precipitation intensity). An improved and expanded set-up installed in 2013 added two additional species (Prunus laurocerasus and Hydrangea quercifolia). The 2013 results confirm interspecies differences in both throughfall amount, and in the relationship of throughfall rate to precipitation intensity. The results are discussed with respect to droplet splashing and enhanced evaporation within the canopy. Both years' findings suggest that the quantity of water intercepted by vegetation canopies exceeds the canopy storage capacity, as assumed in many conventional hydrologic models.

Connecting the failure of K-theory inside and above vegetation canopies and ejection-sweep cycles by a large eddy simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banerjee, Tirtha; De Roo, Frederik; Mauder, Matthias

Parameterizations of biosphere-atmosphere interaction processes in climate models and other hydrological applications require characterization of turbulent transport of momentum and scalars between vegetation canopies and the atmosphere, which is often modeled using a turbulent analogy to molecular diffusion processes. However, simple flux-gradient approaches (K-theory) fail for canopy turbulence. One cause is turbulent transport by large coherent eddies at the canopy scale, which can be linked to sweep-ejection events, and bear signatures of non-local organized eddy motions. K-theory, that parameterizes the turbulent flux or stress proportional to the local concentration or velocity gradient, fails to account for these non-local organized motions. The connection to sweep-ejection cycles and the local turbulent flux can be traced back to the turbulence triple momentmore » $$\\overline{C'W'W'}$$. In this work, we use large-eddy simulation to investigate the diagnostic connection between the failure of K-theory and sweep-ejection motions. Analyzed schemes are quadrant analysis (QA) and a complete and incomplete cumulant expansion (CEM and ICEM) method. The latter approaches introduce a turbulence timescale in the modeling. Furthermore, we find that the momentum flux needs a different formulation for the turbulence timescale than the sensible heat flux. In conclusion, accounting for buoyancy in stratified conditions is also deemed to be important in addition to accounting for non-local events to predict the correct momentum or scalar fluxes.« less

Connecting the failure of K-theory inside and above vegetation canopies and ejection-sweep cycles by a large eddy simulation

DOE PAGES

Banerjee, Tirtha; De Roo, Frederik; Mauder, Matthias

2017-10-19

Parameterizations of biosphere-atmosphere interaction processes in climate models and other hydrological applications require characterization of turbulent transport of momentum and scalars between vegetation canopies and the atmosphere, which is often modeled using a turbulent analogy to molecular diffusion processes. However, simple flux-gradient approaches (K-theory) fail for canopy turbulence. One cause is turbulent transport by large coherent eddies at the canopy scale, which can be linked to sweep-ejection events, and bear signatures of non-local organized eddy motions. K-theory, that parameterizes the turbulent flux or stress proportional to the local concentration or velocity gradient, fails to account for these non-local organized motions. The connection to sweep-ejection cycles and the local turbulent flux can be traced back to the turbulence triple momentmore » $$\\overline{C'W'W'}$$. In this work, we use large-eddy simulation to investigate the diagnostic connection between the failure of K-theory and sweep-ejection motions. Analyzed schemes are quadrant analysis (QA) and a complete and incomplete cumulant expansion (CEM and ICEM) method. The latter approaches introduce a turbulence timescale in the modeling. Furthermore, we find that the momentum flux needs a different formulation for the turbulence timescale than the sensible heat flux. In conclusion, accounting for buoyancy in stratified conditions is also deemed to be important in addition to accounting for non-local events to predict the correct momentum or scalar fluxes.« less

The relationship between tree canopy and crime rates across an urban-rural gradient in the greater Baltimore region

Treesearch

Austin Troy; J. Morgan Grove; Jarlath O' Neill-Dunne

2012-01-01

The extent to which urban tree cover influences crime is in debate in the literature. This research took advantage of geocoded crime point data and high resolution tree canopy data to address this question in Baltimore City and County, MD, an area that includes a significant urban-rural gradient. Using ordinary least squares and spatially adjusted regression and...

Implication of Intrastorm Rainfall-Canopy Interaction on Interception Performance of Broadleaf Evergreen Shrubs in Urban Setting

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2014-12-01

Because of its ability to intercept a portion of rainfall, vegetated canopy has a significant influence on the urban hydrological cycle. In turn, urban watersheds, characterized by large impervious areas, have an enormous and often adverse impact on receiving waters. However, most historical interception research has been dedicated to forest canopies. The goal of our research was to quantify rainfall partitioning by isolated evergreen canopies in an urban setting. Two years of the field experiment involved three exemplars of Cherry Laurel (Prunus laurocerasus'Otto Luyken'.) Each plant had ten rain gauges to measure throughfall with a five second sampling frequency. A number of preventive techniques were introduced to minimize the gauges' errors (e.g., splash-in, splash-out and excessive wetting.) Leaf area index was measured manually. We estimated the canopy storage capacity to be less than 0.5 mm. An on-site automated weather station provided meteorological data. Cumulative interception loss for the periods of August-December 2013 and April-July 2014 was 51%. Phenological change did not show a stable pattern of influence on throughfall depths. Measurements in May and July 2014 showed a high variability of stemflow (2-16%) between rain events. Throughfall and precipitation intensities (mm/hr) expressed strong linear relationships (adjusted coefficient of determination R20.79) for the entire range of observed rainfall intensities. The ratio of throughfall to precipitation intensity was 0.49:1. The observations suggest that reduction of throughfall intensity by the canopy during a rainstorm determines the bulk of interception depth. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception. Simulations of potential evaporation based on the Penman-Monteith method revealed a serious underestimation of evaporation from the wet canopy surfaces during the rain events. Mechanisms other than heat balance models of potential evaporation from a still water surface are being discussed in order to explain large intrastorm evaporation from within an isolated canopy.

Assimilation of Leaf and Canopy Spectroscopic Data to Improve the Representation of Vegetation Dynamics in Terrestrial Ecosystem Models

NASA Astrophysics Data System (ADS)

Serbin, S. P.; Dietze, M.; Desai, A. R.; LeBauer, D.; Viskari, T.; Kooper, R.; McHenry, K. G.; Townsend, P. A.

2013-12-01

The ability to seamlessly integrate information on vegetation structure and function across a continuum of scales, from field to satellite observations, greatly enhances our ability to understand how terrestrial vegetation-atmosphere interactions change over time and in response to disturbances. In particular, terrestrial ecosystem models require detailed information on ecosystem states and canopy properties in order to properly simulate the fluxes of carbon (C), water and energy from the land to the atmosphere as well as address the vulnerability of ecosystems to environmental and other perturbations. Over the last several decades the amount of available data to constrain ecological predictions has increased substantially, resulting in a progressively data-rich era for global change research. In particular remote sensing data, specifically optical data (leaf and canopy), offers the potential for an important and direct data constraint on ecosystem model projections of C and energy fluxes. Here we highlight the utility of coupling information provided through the Ecosystem Spectral Information System (EcoSIS) with complex process models through the Predictive Ecosystem Analyzer (PEcAn; http://www.pecanproject.org/) eco-informatics framework as a means to improve the description of canopy optical properties, vegetation composition, and modeled radiation balance. We also present this an efficient approach for understanding and correcting implicit assumptions and model structural deficiencies. We first illustrate the challenges and issues in adequately characterizing ecosystem fluxes with the Ecosystem Demography model (ED2, Medvigy et al., 2009) due to improper parameterization of leaf and canopy properties, as well as assumptions describing radiative transfer within the canopy. ED2 is especially relevant to these efforts because it contains a sophisticated structure for scaling ecological processes across a range of spatial scales: from the tree-level (demography, physiology) to the distribution of stands across a landscape, which allows for the direct use of remotely sensed data at the appropriate spatial scale. A sensitivity analysis is employed within PEcAn to illustrate the influence of ED2 parameterizations on modeled C and energy fluxes for a northern temperate forest ecosystem as an example of the need for more detailed information on leaf and canopy optical properties. We then demonstrate a data assimilation approach to synthesize spectral data contained within EcoSIS in order to update model parameterizations across key vegetation plant functional types, as well as a means to update vegetation state information (i.e. composition, LAI) and improve the description of radiation transfer through model structural updates. A better understanding of the radiation balance of ecosystems will improve regional and global scale C and energy balance projections.

The effect of urban growth on landscape-scale restoration for a fire-dependent songbird.

PubMed

Pickens, Bradley A; Marcus, Jeffrey F; Carpenter, John P; Anderson, Scott; Taillie, Paul J; Collazo, Jaime A

2017-04-15

A landscape-scale perspective on restoration ecology has been advocated, but few studies have informed restoration with landscape metrics or addressed broad-scale threats. Threats such as urban growth may affect restoration effectiveness in a landscape context. Here, we studied longleaf pine savanna in the rapidly urbanizing southeastern United States where a habitat-specialist bird, Bachman's sparrow (Peucaea aestivalis), is closely associated with savanna vegetation structure and frequent fire. Our objectives were to construct a species distribution model for Bachman's sparrow, determine the relationship between fire and urbanization, quantify the urban growth effect (2010-2090), identify potential restoration areas, and determine the interaction between restoration potential and urban growth by 2050. Number of patches, patch size, and isolation metrics were used to evaluate scenarios. The species distribution model was 88% accurate and emphasized multiscale canopy cover characteristics, fire, and percent habitat. Fires were less common <600 m from urban areas, and this fire suppression effect exacerbated urban growth effects. For restoration scenarios, canopy cover reduction by 30% resulted in nearly double the amount of habitat compared to the prescribed fire scenario; canopy cover reduction resulted in larger patch sizes and less patch isolation compared to current conditions. The effect of urban growth on restoration scenarios was unequal. Seventy-four percent of restoration areas from the prescribed fire scenario overlapped with projected urban growth, whereas the canopy cover reduction scenario only overlapped by 9%. We emphasize the benefits of simultaneously considering the effects of urban growth and landscape-scale restoration potential to promote a landscape with greater patch sizes and less isolation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Numerical Study of the Response of an Atmospheric Surface Layer to a Spatially Nonuniform Plant Canopy

NASA Astrophysics Data System (ADS)

Qiu, J.; Gu, Z. L.; Wang, Z. S.

2008-05-01

High-accuracy large-eddy simulations of neutral atmospheric surface-layer flow over a gapped plant canopy strip have been performed. Subgrid-scale (SGS) motions are parameterized by the Sagaut mixed length SGS model, with a modification to compute the SGS characteristic length self-adaptively. Shaw’s plant canopy model, taking the vertical variation of leaf area density into account, is applied to study the response of the atmospheric surface layer to the gapped dense forest strip. Differences in the region far away from the gap and in the middle of the gap are investigated, according to the instantaneous velocity magnitude, the zero-plane displacement, the potential temperature and the streamlines. The large-scale vortex structure, in the form of a roll vortex, is revealed in the region far away from the gap. The nonuniform spatial distribution of plants appears to cause the formation of the coherent structure. The roll vortex starts in the wake of the canopy, and results in strong fluctuations throughout the entire canopy region. Wind sweeps and ejections in the plant canopy are also attributed to the large vortex structure.

A comparative study of some mathematical models of the mean wind structure and aerodynamic drag of plant canopies

NASA Technical Reports Server (NTRS)

Massman, William

1987-01-01

A semianalytical method for describing the mean wind profile and shear stress within plant canopies and for estimating the roughness length and the displacement height is presented. This method incorporates density and vertical structure of the canopy and includes simple parameterizations of the roughness sublayer and shelter factor. Some of the wind profiles examined are consistent with first-order closure techniques while others are consistent with second-order closure techniques. Some profiles show a shearless region near the base of the canopy; however, none displays a secondary maximum there. Comparing several different analytical expressions for the canopy wind profile against observations suggests that one particular type of profile (an Airy function which is associated with the triangular foliage surface area density distribution) is superior to the others. Because of the numerical simplicity of the methods outlined, it is suggested that they may be profitably used in large-scale models of plant-atmosphere exchanges.

Urban landscape genetics: canopy cover predicts gene flow between white-footed mouse (Peromyscus leucopus) populations in New York City.

PubMed

Munshi-South, Jason

2012-03-01

In this study, I examine the influence of urban canopy cover on gene flow between 15 white-footed mouse (Peromyscus leucopus) populations in New York City parklands. Parks in the urban core are often highly fragmented, leading to rapid genetic differentiation of relatively nonvagile species. However, a diverse array of 'green' spaces may provide dispersal corridors through 'grey' urban infrastructure. I identify urban landscape features that promote genetic connectivity in an urban environment and compare the success of two different landscape connectivity approaches at explaining gene flow. Gene flow was associated with 'effective distances' between populations that were calculated based on per cent tree canopy cover using two different approaches: (i) isolation by effective distance (IED) that calculates the single best pathway to minimize passage through high-resistance (i.e. low canopy cover) areas, and (ii) isolation by resistance (IBR), an implementation of circuit theory that identifies all low-resistance paths through the landscape. IBR, but not IED, models were significantly associated with three measures of gene flow (Nm from F(ST) , BayesAss+ and Migrate-n) after factoring out the influence of isolation by distance using partial Mantel tests. Predicted corridors for gene flow between city parks were largely narrow, linear parklands or vegetated spaces that are not managed for wildlife, such as cemeteries and roadway medians. These results have implications for understanding the impacts of urbanization trends on native wildlife, as well as for urban reforestation efforts that aim to improve urban ecosystem processes. © 2012 Blackwell Publishing Ltd.

EXPERIMENTAL AND MODEL-COMPUTED AREA AVERAGED VERTICAL PROFILES OF WIND SPEED FOR EVALUATION OF MESOSCALE URBAN CANOPY SCHEMES

EPA Science Inventory

Numerous urban canopy schemes have recently been developed for mesoscale models in order to approximate the drag and turbulent production effects of a city on the air flow. However, little data exists by which to evaluate the efficacy of the schemes since "area-averaged&quo...

Optimizing the Determination of Roughness Parameters for Model Urban Canopies

NASA Astrophysics Data System (ADS)

Huq, Pablo; Rahman, Auvi

2018-05-01

We present an objective optimization procedure to determine the roughness parameters for very rough boundary-layer flow over model urban canopies. For neutral stratification the mean velocity profile above a model urban canopy is described by the logarithmic law together with the set of roughness parameters of displacement height d, roughness length z_0 , and friction velocity u_* . Traditionally, values of these roughness parameters are obtained by fitting the logarithmic law through (all) the data points comprising the velocity profile. The new procedure generates unique velocity profiles from subsets or combinations of the data points of the original velocity profile, after which all possible profiles are examined. Each of the generated profiles is fitted to the logarithmic law for a sequence of values of d, with the representative value of d obtained from the minima of the summed least-squares errors for all the generated profiles. The representative values of z_0 and u_* are identified by the peak in the bivariate histogram of z_0 and u_* . The methodology has been verified against laboratory datasets of flow above model urban canopies.

Forcing variables in simulation of transpiration of water stressed plants determined by principal component analysis

NASA Astrophysics Data System (ADS)

Durigon, Angelica; Lier, Quirijn de Jong van; Metselaar, Klaas

2016-10-01

To date, measuring plant transpiration at canopy scale is laborious and its estimation by numerical modelling can be used to assess high time frequency data. When using the model by Jacobs (1994) to simulate transpiration of water stressed plants it needs to be reparametrized. We compare the importance of model variables affecting simulated transpiration of water stressed plants. A systematic literature review was performed to recover existing parameterizations to be tested in the model. Data from a field experiment with common bean under full and deficit irrigation were used to correlate estimations to forcing variables applying principal component analysis. New parameterizations resulted in a moderate reduction of prediction errors and in an increase in model performance. Ags model was sensitive to changes in the mesophyll conductance and leaf angle distribution parameterizations, allowing model improvement. Simulated transpiration could be separated in temporal components. Daily, afternoon depression and long-term components for the fully irrigated treatment were more related to atmospheric forcing variables (specific humidity deficit between stomata and air, relative air humidity and canopy temperature). Daily and afternoon depression components for the deficit-irrigated treatment were related to both atmospheric and soil dryness, and long-term component was related to soil dryness.

Investigating the vertical dimension of Singapore's urban heat island through quadcopter platforms: an pilot study

NASA Astrophysics Data System (ADS)

Chow, Winston; Ho, Dawn

2016-04-01

In numerous cities, measurements of urban warmth in most urban heat island (UHI) studies are generally constrained towards surface or near-surface (<2 m above surface level) levels across horizontal variations in land use and land cover. However, there has been hitherto limited attention towards the measurement of vertical temperature profiles extending from the urban surface, urban canopy layer through to the urban boundary layer. Knowledge of these profiles, through (a.) how they vary over different local urban morphologies, and (b.) develop with respect to synoptic meteorological conditions, are important towards several aspects of UHI research; these include validating modelling urban canopy lapse rate profiles or estimating the growth of urban plumes. In this novel study, we utilised temperature sensor-loggers attached onto remote controlled aerial quadcopter platforms to measure urban temperature profiles up to 100 m above ground level in Singapore, which is a rapidly urbanizing major tropical metropolis. Three different land use/land cover categories were sampled; a high-rise residential estate, a university campus, and an urban park/green-space. Sorties were flown repeatedly at four different times - sunrise, noon, sunset and midnight. Initial results indicate significant variations in intra-site stability and inversion development between the urban canopy and boundary layers. These profiles are also temporally dynamic, depending on the time of day and larger-scale weather conditions.

Increased Spatial Variability and Intensification of Extreme Monsoon Rainfall due to Urbanization.

PubMed

Paul, Supantha; Ghosh, Subimal; Mathew, Micky; Devanand, Anjana; Karmakar, Subhankar; Niyogi, Dev

2018-03-02

While satellite data provides a strong robust signature of urban feedback on extreme precipitation; urbanization signal is often not so prominent with station level data. To investigate this, we select the case study of Mumbai, India and perform a high resolution (1 km) numerical study with Weather Research and Forecasting (WRF) model for eight extreme rainfall days during 2014-2015. The WRF model is coupled with two different urban schemes, the Single Layer Urban Canopy Model (WRF-SUCM), Multi-Layer Urban Canopy Model (WRF-MUCM). The differences between the WRF-MUCM and WRF-SUCM indicate the importance of the structure and characteristics of urban canopy on modifications in precipitation. The WRF-MUCM simulations resemble the observed distributed rainfall. WRF-MUCM also produces intensified rainfall as compared to the WRF-SUCM and WRF-NoUCM (without UCM). The intensification in rainfall is however prominent at few pockets of urban regions, that is seen in increased spatial variability. We find that the correlation of precipitation across stations within the city falls below statistical significance at a distance greater than 10 km. Urban signature on extreme precipitation will be reflected on station rainfall only when the stations are located inside the urban pockets having intensified precipitation, which needs to be considered in future analysis.

Mapping Urban Tree Canopy Coverage and Structure using Data Fusion of High Resolution Satellite Imagery and Aerial Lidar

NASA Astrophysics Data System (ADS)

Elmes, A.; Rogan, J.; Williams, C. A.; Martin, D. G.; Ratick, S.; Nowak, D.

2015-12-01

Urban tree canopy (UTC) coverage is a critical component of sustainable urban areas. Trees provide a number of important ecosystem services, including air pollution mitigation, water runoff control, and aesthetic and cultural values. Critically, urban trees also act to mitigate the urban heat island (UHI) effect by shading impervious surfaces and via evaporative cooling. The cooling effect of urban trees can be seen locally, with individual trees reducing home HVAC costs, and at a citywide scale, reducing the extent and magnitude of an urban areas UHI. In order to accurately model the ecosystem services of a given urban forest, it is essential to map in detail the condition and composition of these trees at a fine scale, capturing individual tree crowns and their vertical structure. This paper presents methods for delineating UTC and measuring canopy structure at fine spatial resolution (<1m). These metrics are essential for modeling the HVAC benefits from UTC for individual homes, and for assessing the ecosystem services for entire urban areas. Such maps have previously been made using a variety of methods, typically relying on high resolution aerial or satellite imagery. This paper seeks to contribute to this growing body of methods, relying on a data fusion method to combine the information contained in high resolution WorldView-3 satellite imagery and aerial lidar data using an object-based image classification approach. The study area, Worcester, MA, has recently undergone a large-scale tree removal and reforestation program, following a pest eradication effort. Therefore, the urban canopy in this location provides a wide mix of tree age class and functional type, ideal for illustrating the effectiveness of the proposed methods. Early results show that the object-based classifier is indeed capable of identifying individual tree crowns, while continued research will focus on extracting crown structural characteristics using lidar-derived metrics. Ultimately, the resulting fine resolution UTC map will be compared with previously created UTC maps of the same area but for earlier dates, producing a canopy change map corresponding to the Worcester area tree removal and replanting effort.

Tree Canopy Cover Mapping Using LiDAR in Urban Barangays of Cebu City, Central Philippines

NASA Astrophysics Data System (ADS)

Ejares, J. A.; Violanda, R. R.; Diola, A. G.; Dy, D. T.; Otadoy, J. B.; Otadoy, R. E. S.

2016-06-01

This paper investigates tree canopy cover mapping of urban barangays (smallest administrative division in the Philippines) in Cebu City using LiDAR (Light Detection and Ranging). Object-Based Image Analysis (OBIA) was used to extract tree canopy cover. Multi-resolution segmentation and a series of assign-class algorithm in eCognition software was also performed to extract different land features. Contextual features of tree canopies such as height, area, roundness, slope, length-width and elliptic fit were also evaluated. The results showed that at the time the LiDAR data was collected (June 24, 2014), the tree cover was around 25.11 % (or 15,674,341.8 m2) of the city's urban barangays (or 62,426,064.6 m2). Among all urban barangays in Cebu City, Barangay Busay had the highest cover (55.79 %) while barangay Suba had the lowest (0.8 %). The 16 barangays with less than 10 % tree cover were generally located in the coastal area, presumably due to accelerated urbanization. Thirty-one barangays have tree cover ranging from 10.59--27.3 %. Only 3 barangays (i.e., Lahug, Talamban, and Busay) have tree cover greater than 30 %. The overall accuracy of the analysis was 96.6 % with the Kappa Index of Agreement or KIA of 0.9. From the study, a grouping can be made of the city's urban barangays with regards to tree cover. The grouping will be useful to urban planners not only in allocating budget to the tree planting program of the city but also in planning and creation of urban parks and playgrounds.

Environmental Response of Small Urban Parks in Context of Dhaka City

NASA Astrophysics Data System (ADS)

Tabassum, S.

2018-01-01

Urban green spaces are essential element of urban life which, due to their structure and multi functionality, can play an exemplary role in the vitality and quality of urban life. Urban Parks are not only used as active recreational and leisure areas for its citizens but also an important catalyst for community development and enhancement. These spaces in the city act like its lungs and play a critical role in supporting the ecological and environmental system. In the dense urban areas, even Small Parks (less than one acre in size) can also contribute a lot to improve environmental quality of city life. In a populated city where it is difficult to incorporate large Public Parks, these small green area can complement large Public Park system. Accordingly the study is concerned to evaluate the environmental performances of Small Parks on the built environments of urban Dhaka. The analysis identifies that Small Parks has strong environmental impact, the intensity of which depends on the type and quality of its vegetation, its design parameters, connectivity and of course on surrounding urban morphology. And it is confirmed that park with more canopy tree is suitable for our environment and therefore a good combination of vegetation (wide canopy trees at periphery, medium canopy trees beside internal walkway and small canopy tree, shrub and grass cover elsewhere) are recommended for better environmental performance of Small Parks. The research will be an approach to find the ways and means to restore the Small Parks of Dhaka city to ensure the livability of the city and enhance the quality of city image.

A Note on Spatial Averaging and Shear Stresses Within Urban Canopies

NASA Astrophysics Data System (ADS)

Xie, Zheng-Tong; Fuka, Vladimir

2018-04-01

One-dimensional urban models embedded in mesoscale numerical models may place several grid points within the urban canopy. This requires an accurate parametrization for shear stresses (i.e. vertical momentum fluxes) including the dispersive stress and momentum sinks at these points. We used a case study with a packing density of 33% and checked rigorously the vertical variation of spatially-averaged total shear stress, which can be used in a one-dimensional column urban model. We found that the intrinsic spatial average, in which the volume or area of the solid parts are not included in the average process, yield greater time-spatial average of total stress within the canopy and a more evident abrupt change at the top of the buildings than the comprehensive spatial average, in which the volume or area of the solid parts are included in the average.

A high-resolution large-eddy simulation of turbulent flow within and above urban-like canopies

NASA Astrophysics Data System (ADS)

Maché, M.; Calmet, I.; Sini, J.-F.

2009-09-01

The urban microclimate is a result of the interactions between regional climatology, morphology of urban fabric and thermo-radiative and hydric properties of the materials constituting the urban surfaces. Modern urban planning tries to compact cities for avoiding spreading of the town area in order to reduce the need of transports. The climatic effects of this politic are not well known yet. This work is the first step of a study whose main purpose is to propose an urban planning politic which considers the urban heat island within the context of the climate change. Therefore it aims to understand the effects of building configuration on the momentum, heat and humidity turbulent transfers. Urban structures are quite heterogeneous and complex. To analyse the interactions between urban canopies and the atmosphere, the resolution has to be high enough that mean flow characteristics between the buildings can be observed as well as turbulent structures that develop above roof level. For that purpose, the Large-Eddy Simulation atmospheric model ARPS (Advanced Regional Prediction System) is employed. The subgrid scales are modelled by means of the resolution of an equation for the subgrid-scale turbulent kinetic energy. The version used is this study is based on the developments of Dupont & Brunet (2008) who introduced a drag force approach to simulate the influence of the vegetal covers on the low atmosphere. The application of this model on urban canopies requires adjusting the drag coefficient (Cd) in function of the frontal density (Af) and of the building arrangement. Its dependency on configuration (staggered or aligned arrays) and on frontal density is investigated. In order to put in light the main characteristics of the flow field and to validate the model in urban configurations, the turbulent flow above arrays of obstacles is investigated here for different arrangements and packing densities. The grid spacing is set to a few tens of meters in both horizontal directions and one meter in vertical direction, within the canopy. Above the canopy, grids are stretched vertically to reach four meters in average. The surface density Af is calculated in function of the geometry of the obstacles present in a grid cell. The effect of Cd values on the turbulent statistics is compared with results from wind tunnel experiments or building resolving simulations. The ability of the model to reproduce the major turbulent organized structures above the canopy and the influence of the building configuration is also studied, in terms of intensity, size and orientation of the structures. Further research will be done to investigate the effect of configuration of buildings with more complex geometries, like variable building height, on turbulent flow characteristics. To understand the climatologic features of a real city this approach will be completed by the introduction of a parametrization for heat and humidity exchanges inside the canopy.

Estimation of NH3 Bi-Directional Flux from Managed Agricultural Soils

EPA Science Inventory

The Community Multi-Scale Air Quality model (CMAQ v4.7) contains a bi-directional ammonia (NH₃) flux option that computes emission and deposition of ammonia derived from commercial fertilizer via a temperature dependent parameterization of canopy and soil compensation ...

Simulating imaging spectrometer data of a mixed old-growth forest: A parameterization of a 3D radiative transfer model based on airborne and terrestrial laser scanning

NASA Astrophysics Data System (ADS)

Schneider, F. D.; Leiterer, R.; Morsdorf, F.; Gastellu-Etchegorry, J.; Lauret, N.; Pfeifer, N.; Schaepman, M. E.

2013-12-01

Remote sensing offers unique potential to study forest ecosystems by providing spatially and temporally distributed information that can be linked with key biophysical and biochemical variables. The estimation of biochemical constituents of leaves from remotely sensed data is of high interest revealing insight on photosynthetic processes, plant health, plant functional types, and speciation. However, the scaling of observations at the canopy level to the leaf level or vice versa is not trivial due to the structural complexity of forests. Thus, a common solution for scaling spectral information is the use of physically-based radiative transfer models. The discrete anisotropic radiative transfer model (DART), being one of the most complete coupled canopy-atmosphere 3D radiative transfer models, was parameterized based on airborne and in-situ measurements. At-sensor radiances were simulated and compared with measurements from an airborne imaging spectrometer. The study was performed on the Laegern site, a temperate mixed forest characterized by steep slopes, a heterogeneous spectral background, and deciduous and coniferous trees at different development stages (dominated by beech trees; 47°28'42.0' N, 8°21'51.8' E, 682 m asl, Switzerland). It is one of the few studies conducted on an old-growth forest. Particularly the 3D modeling of the complex canopy architecture is crucial to model the interaction of photons with the vegetation canopy and its background. Thus, we developed two forest reconstruction approaches: 1) based on a voxel grid, and 2) based on individual tree detection. Both methods are transferable to various forest ecosystems and applicable at scales between plot and landscape. Our results show that the newly developed voxel grid approach is favorable over a parameterization based on individual trees. In comparison to the actual imaging spectrometer data, the simulated images exhibit very similar spatial patterns, whereas absolute radiance values are partially differing depending on the respective wavelength. We conclude that our proposed method provides a representation of the 3D radiative regime within old-growth forests that is suitable for simulating most spectral and spatial features of imaging spectrometer data. It indicates the potential of simulating future Earth observation missions, such as ESA's Sentinel-2. However, the high spectral variability of leaf optical properties among species has to be addressed in future radiative transfer modeling. The results further reveal that research emphasis has to be put on the accurate parameterization of small-scale structures, such as the clumping of needles into shoots or the distribution of leaf angles.

Controls on Biogeochemical Cycling of Nitrogen in Urban Ecosystems

NASA Astrophysics Data System (ADS)

Templer, P. H.; Hutyra, L.; Decina, S.; Rao, P.; Gately, C.

2017-12-01

Rates of atmospheric nitrogen deposition are declining across much of the United States and Europe, yet they remain substantially elevated by almost an order of magnitude over pre-industrial levels and occur as hot spots in urban areas. We measured atmospheric inputs of inorganic and organic nitrogen in multiple urban sites around the Boston Metropolitan area, finding that urban rates are substantially elevated compared to nearby rural areas, and that the range of these atmospheric inputs are as large as observed urban to rural gradients. Within the City of Boston, the variation in deposition fluxes can be explained by traffic intensity, vehicle emissions, and spring fertilizer additions. Throughfall inputs of nitrogen are approximately three times greater than bulk deposition inputs in the city, demonstrating that the urban canopy amplifies rates of nitrogen reaching the ground surface. Similar to many other metropolitan areas of the United States, the City of Boston has 25% canopy cover; however, 25% of this tree canopy is located above impervious pavement. Throughfall inputs that do not have soil below the canopy to retain excess nitrogen may lead to greater inputs of nitrogen into nearby waterways through runoff. Most measurement stations for atmospheric nitrogen deposition are intentionally located away from urban areas and point sources of pollution to capture regional trends. Our data show that a major consequence of this network design is that hotspots of nitrogen deposition and runoff into urban and coastal waterways is likely underestimated to a significant degree. A more complete determination of atmospheric nitrogen deposition and its fate in urban ecosystems is critical for closing regional nitrogen budgets and for improving our understanding of biogeochemical nitrogen cycling across multiple spatial scales.

What Does a Multilayer Canopy Model Tell Us About Our Current Understanding of Snow-Canopy Unloading?

NASA Astrophysics Data System (ADS)

McGowan, L. E.; Paw U, K. T.; Dahlke, H. E.

2017-12-01

In the Western U.S., future water resources depend on the forested mountain snowpack. The variations in and estimates of forest mountain snow volume are vital to projecting annual water availability; yet, snow forest processes are not fully known. Most snow models calculate snow-canopy unloading based on time, temperature, Leaf Area Index (LAI), and/or wind speed. While models crudely consider the canopy shape via LAI, current models typically do not consider the vertical canopy structure or varied energetics within multiple canopy layers. Vertical canopy structure influences the spatiotemporal distribution of snow, and therefore ultimately determines the degree and extent by which snow alters both the surface energy balance and water availability. Within the canopy both the snowpack and energetic exposures to the snowpack (wind, shortwave and longwave radiation, turbulent heat fluxes etc.) vary widely in the vertical. The water and energy balance in each layer is dependent on all other layers. For example, increased snow canopy content in the top of the canopy will reduce available shortwave radiation at the bottom and snow unloading in a mid-layer can cascade and remove snow from all the lower layers. We examined vertical interactions and structures of the forest canopy on the impact of unloading utilizing the Advanced Canopy-Atmosphere-Soil-Algorithm (ACASA), a multilayer soil-vegetation-atmosphere numerical model based on higher-order closure of turbulence equations. Our results demonstrate how a multilayer model can be used to elucidate the physical processes of snow unloading, and could help researchers better parameterize unloading in snow-hydrology models.

Determining light requirements of groundcover plants from subtropical natural forest using hemispherical photography

NASA Astrophysics Data System (ADS)

Zhang, Yi; Zhong, Yonglin; Xu, Mingfeng; Su, Zhiyao

2017-01-01

In order to determine light requirements of indigenous groundcover plants for potential use in urban landscaping, we conducted a plant census in Yinpingshan Nature Reserve, Dongguan, China, and measured canopy structure and understory light regimes using hemispherical photography. We found that canopy openness, transmitted direct solar radiation, and transmitted diffuse solar radiation exhibited highly significant spatial heterogeneity. Species composition and diversity of groundcover plants were highly dependent on canopy structure and understory light condition. Greater diversity and more stems of groundcover plants were associated with greater canopy openness and understory radiation in most cases. Highly significant differences in species composition were detected along canopy openness, transmitted direct solar radiation, and transmitted diffuse solar radiation gradients, respectively. We also detected indicator species for specific understory light regimes, which will provide useful information when applying such species in urban greening under various light environments.

Application of the ACASA model for urban development studies

NASA Astrophysics Data System (ADS)

Marras, S.; Pyles, R. D.; Falk, M.; Snyder, R. L.; Paw U, K. T.; Blecic, I.; Trunfio, G. A.; Cecchini, A.; Spano, D.

2012-04-01

Since urban population is growing fast and urban areas are recognized as the major source of CO2 emissions, more attention has being dedicated to the topic of urban sustainability and its connection with the climate. Urban flows of energy, water and carbon have an important impact on climate change and their quantification is pivotal in the city design and management. Large effort has been devoted to quantitative estimates of the urban metabolism components, and several advanced models have been developed and used at different spatial and temporal scales for this purpose. However, it is necessary to develop suitable tools and indicators to effectively support urban planning and management with the goal of achieving a more sustainable metabolism in the urban environment. In this study, the multilayer model ACASA (Advanced Canopy-Atmosphere-Soil Algorithm) was chosen to simulate the exchanges of heat, water vapour and CO2 within and above urban canopy. After several calibration and evaluation tests over natural and agricultural ecosystems, the model was recently modified for application in urban and peri-urban areas. New equations to account for the anthropogenic contribution to heat exchange and carbon production, as well as key parameterizations of leaf-facet scale interactions to separate both biogenic and anthropogenic flux sources and sinks, were added to test changes in land use or urban planning strategies. The analysis was based on the evaluation of the ACASA model performance in estimating urban metabolism components at local scale. Simulated sensible heat, latent heat, and carbon fluxes were compared with in situ Eddy Covariance measurements collected in the city centre of Florence (Italy). Statistical analysis was performed to test the model accuracy and reliability. Model sensitivity to soil types and increased population density values was conducted to investigate the potential use of ACASA for evaluating the impact of planning alternative scenarios. In this contest, an in progress application of ACASA for estimating carbon exchanges alternative scenarios is represented by its integration in a software framework composed by: (i) a Cellular Automata model to simulate the urban land-use dynamics; (ii) a transportation model, able to estimate the variation of the transportation network load; (iii) the ACASA model, and (iv) the mesoscale weather model WRF for the estimation of the relevant urban metabolism components at regional scale. The CA module is able to produce future land use maps, which represent a spatial distribution of the aggregate land-use demand consistent with the main rules governing the functioning of an urban system. Such future land use maps, together with the street network including the current traffic data, are used by the transportation module for estimating future traffic data coherent with the assumed land uses trends. All these information are then used by the coupled model WRF-ACASA for estimating future maps of CO2 fluxes in the urban area under consideration, allowing to estimate the impact of future planning strategies in reducing C emissions. The in-progress application of this system to the city of Florence is presented here.

A comparison of two sampling approaches for assessing the urban forest canopy cover from aerial photography.

Treesearch

Ucar Zennure; Pete Bettinger; Krista Merry; Jacek Siry; J.M. Bowker

2016-01-01

Two different sampling approaches for estimating urban tree canopy cover were applied to two medium-sized cities in the United States, in conjunction with two freely available remotely sensed imagery products. A random point-based sampling approach, which involved 1000 sample points, was compared against a plot/grid sampling (cluster sampling) approach that involved a...

Trees grow on money: Urban tree canopy cover and environmental justice

Treesearch

Kirsten Schwarz; Michail Fragkias; Christopher G. Boone; Weiqi Zhou; Melissa McHale; J. Morgan Grove; Jarlath O' Neil-Dunne; Joseph P. McFadden; Geoffrey L. Buckley; Dan Childers; Laura Ogden; Stephanie Pincetl; Diane Pataki; Ali Whitmer; Mary L. Cadenasso; Steven Arthur Loiselle

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman’s correlation, ordinary least squares...

Impact of water use efficiency parameterization on partitioning evapotranspiration with the eddy covariance flux variance method

USDA-ARS?s Scientific Manuscript database

Partitioned observations of evapotranspiration (ET) into its constituent components of soil and canopy evaporation (E) and plant transpiration (T) are needed to validate many agricultural water use models. E and T observations are also useful for assessing management practices to reduce crop water ...

The Effects of Fine-scale Soil Moisture and Canopy Heterogeneities on Energy and Soil Water Fluxes in a Temperate Mixed Deciduous Forest

NASA Astrophysics Data System (ADS)

He, L.; Ivanov, V. Y.; Bohrer, G.; Maurer, K.; Vogel, C. S.; Moghaddam, M.

2011-12-01

Vegetation is heterogeneous at different scales, influencing spatially variable energy and water exchanges between land-surface and atmosphere. Current land surface parameterizations of large-scale models consider spatial variability at a scale of a few kilometers and treat vegetation cover as aggregated patches with uniform properties. However, the coupling mechanisms between fine-scale soil moisture, vegetation, and energy fluxes such as evapotranspiration are strongly nonlinear; the aggregation of surface variations may produce biased energy fluxes. This study aims to improve the understanding of the scale impact in atmosphere-biosphere-hydrosphere interactions, which affects predictive capabilities of land surface models. The study uses a high-resolution, physically-based ecohydrological model tRIBS + VEGGIE as a data integration tool to upscale the heterogeneity of canopy distribution resolved at a few meters to the watershed scale. The study was carried out for a spatially heterogeneous, temperate mixed forest environment of Northern Michigan located near the University of Michigan Biological Station (UMBS). Energy and soil water dynamics were simulated at the tree-canopy resolution in the horizontal plane for a small domain (~2 sq. km) located within a footprint of the AmeriFlux tower. A variety of observational data were used to constrain and confirm the model, including a 3-m profile continuous soil moisture dataset and energy flux data (measured at the AmeriFlux tower footprint). A scenario with a spatially uniform canopy, corresponding to the commonly used 'big-leaf' scheme in land surface parameterizations was used to infer the effects of coarse-scale averaging. To gain insights on how heterogeneous canopy and soil moisture interact and contribute to the domain-averaged transpiration, several scenarios of tree-scale leaf area and soil moisture spatial variability were designed. Specifically, for the same mean states, the scenarios of variability of canopy biomass account for the spatial distribution of photosynthesis (and thus the stomatal resistance), the aerodynamic and leaf boundary layer resistances as well as the differential radiation forcing due to tall tree exposure and lateral shading of short trees. The numerical experiments show that by transpiring spatially varying amounts of water, heterogeneous canopies adjust the spatial soil water state to the scaled inverse of the canopy biomass regardless of the initial moisture state. Such a spatial distribution can be further wiped out because of the differential water stress. The aggregation of canopy-scale atmosphere-biosphere-hydrosphere interactions demonstrates non-linear relationship between soil moisture and evapotranspiration, influencing domain-averaged energy fluxes.

Implication of Intrastorm Rainfall-Canopy Interaction on Interception Performance of Broadleaf Evergreen Shrubs in an Ultra-Urban Setting

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2015-12-01

Because of its ability to intercept a portion of rainfall, vegetated canopies can play substantial role in modulating the urban hydrological cycle. However, canopy interception research has historically been focused to forest canopies. The goal of our research is to quantify rainfall partitioning by isolated evergreen shrub canopies in an ultra-urban setting. The three year field experiment involved three exemplars of cherry laurel (Prunus laurocerasus 'Otto Luyken'.) Ten rain gauges positioned under each plant were used to measure throughfall with a sampling frequency of five seconds. A number of specific techniques were implemented to minimize error associated with the gauges, e.g., splash-in, splash-out and excessive wetting. The cumulative throughfall deficit (i.e., gross precipitation minus throughfall within the canopy projected area and minus stemflow) for the periods of August-December 2013, April-December 2014 and April-July 2015 was 39%. Spatial variability of throughfall was large (coefficient of variation up to 1.5.) Stable areas of preferential throughfall flux were observed. Stemflow showed a high variability (1.4 - 24%) between rain events. The relationship between throughfall and precipitation intensity was strongly linear (adjusted coefficient of determination R2 0.79) throughout the entire range of observed rainfall intensities. The overall ratio of throughfall to precipitation intensity was 0.48:1. The observations suggest that reduction of throughfall intensity by the canopy during a rainstorm determines the aggregate interception depth. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception loss. Penman-Monteith estimates of wet canopy evaporation cannot account for the throughfall deficit. Lateral displacement of microdrops beyond the canopy projected area is another phenomenon that will be discussed and most recent observations of an extended gauge network will be presented.

Investigation of the flow inside an urban canopy immersed into an atmospheric boundary layer using laser Doppler anemometry

NASA Astrophysics Data System (ADS)

Herpin, Sophie; Perret, Laurent; Mathis, Romain; Tanguy, Christian; Lasserre, Jean-Jacques

2018-05-01

Laser Doppler anemometry (LDA) is used to investigate the flow inside an idealized urban canopy consisting of a staggered array of cubes with a 25% density immersed into an atmospheric boundary layer with a Reynolds number of δ ^+=32{,}300. The boundary layer thickness to cube height ratio (δ /h=22.7) is large enough to be representative of atmospheric surface layer in neutral conditions. The LDA measurements give access to pointwise time-resolved data at several positions inside the canopy (z=h/4, h/2, and h). Synchronized hot-wire measurements above the canopy (inertial region and roughness sublayer) are also realized to get access to interactions between the different flow regions. The wall-normal mean velocity profile and Reynolds stresses show a good agreement with available data in the literature, although some differences are observed on the standard deviation of the spanwise component. A detailed spectral and integral time scale analysis inside the canopy is then carried out. No clear footprint of a periodic vortex shedding on the sides of the cubes could be identified on the power spectra, owing to the multiple cube-to-cube interactions occuring within a canopy with a building density in the wake interference regime. Results also suggest that interactions between the most energetics scales of the boundary layer and those related to the cube canopy take place, leading to a broadening of the energy peak in the spectra within the canopy. This is confirmed by the analysis of coherence results between the flow inside and above the canopy. It is shown that linear interactions mechanisms are significant, but reduced compared to smooth-wall boundary-layer flow. To our knowledge, this is the first time such results are shown on the dynamics of the flow inside an urban canopy.

Parametrization of Drag and Turbulence for Urban Neighbourhoods with Trees

NASA Astrophysics Data System (ADS)

Krayenhoff, E. S.; Santiago, J.-L.; Martilli, A.; Christen, A.; Oke, T. R.

2015-08-01

Urban canopy parametrizations designed to be coupled with mesoscale models must predict the integrated effect of urban obstacles on the flow at each height in the canopy. To assess these neighbourhood-scale effects, results of microscale simulations may be horizontally-averaged. Obstacle-resolving computational fluid dynamics (CFD) simulations of neutrally-stratified flow through canopies of blocks (buildings) with varying distributions and densities of porous media (tree foliage) are conducted, and the spatially-averaged impacts on the flow of these building-tree combinations are assessed. The accuracy with which a one-dimensional (column) model with a one-equation (-) turbulence scheme represents spatially-averaged CFD results is evaluated. Individual physical mechanisms by which trees and buildings affect flow in the column model are evaluated in terms of relative importance. For the treed urban configurations considered, effects of buildings and trees may be considered independently. Building drag coefficients and length scale effects need not be altered due to the presence of tree foliage; therefore, parametrization of spatially-averaged flow through urban neighbourhoods with trees is greatly simplified. The new parametrization includes only source and sink terms significant for the prediction of spatially-averaged flow profiles: momentum drag due to buildings and trees (and the associated wake production of turbulent kinetic energy), modification of length scales by buildings, and enhanced dissipation of turbulent kinetic energy due to the small scale of tree foliage elements. Coefficients for the Santiago and Martilli (Boundary-Layer Meteorol 137: 417-439, 2010) parametrization of building drag coefficients and length scales are revised. Inclusion of foliage terms from the new parametrization in addition to the Santiago and Martilli building terms reduces root-mean-square difference (RMSD) of the column model streamwise velocity component and turbulent kinetic energy relative to the CFD model by 89 % in the canopy and 71 % above the canopy on average for the highest leaf area density scenarios tested: . RMSD values with the new parametrization are less than 20 % of mean layer magnitude for the streamwise velocity component within and above the canopy, and for above-canopy turbulent kinetic energy; RMSD values for within-canopy turbulent kinetic energy are negligible for most scenarios. The foliage-related portion of the new parametrization is required for scenarios with tree foliage of equal or greater height than the buildings, and for scenarios with foliage below roof height for building plan area densities less than approximately 0.25.

A Graphical User Interface for Parameterizing Biochemical Models of Photosynthesis and Chlorophyll Fluorescence

NASA Astrophysics Data System (ADS)

Kornfeld, A.; Van der Tol, C.; Berry, J. A.

2015-12-01

Recent advances in optical remote sensing of photosynthesis offer great promise for estimating gross primary productivity (GPP) at leaf, canopy and even global scale. These methods -including solar-induced chlorophyll fluorescence (SIF) emission, fluorescence spectra, and hyperspectral features such as the red edge and the photochemical reflectance index (PRI) - can be used to greatly enhance the predictive power of global circulation models (GCMs) by providing better constraints on GPP. The way to use measured optical data to parameterize existing models such as SCOPE (Soil Canopy Observation, Photochemistry and Energy fluxes) is not trivial, however. We have therefore extended a biochemical model to include fluorescence and other parameters in a coupled treatment. To help parameterize the model, we then use nonlinear curve-fitting routines to determine the parameter set that enables model results to best fit leaf-level gas exchange and optical data measurements. To make the tool more accessible to all practitioners, we have further designed a graphical user interface (GUI) based front-end to allow researchers to analyze data with a minimum of effort while, at the same time, allowing them to change parameters interactively to visualize how variation in model parameters affect predicted outcomes such as photosynthetic rates, electron transport, and chlorophyll fluorescence. Here we discuss the tool and its effectiveness, using recently-gathered leaf-level data.

A Canopy Architectural Model to Study the Competitive Ability of Chickpea with Sowthistle

PubMed Central

Cici, S-Zahra-Hosseini; Adkins, Steve; Hanan, Jim

2008-01-01

Background and Aims Improving the competitive ability of crops is a sustainable method of weed management. This paper shows how a virtual plant model of competition between chickpea (Cicer arietinum) and sowthistle (Sonchus oleraceus) can be used as a framework for discovering and/or developing more competitive chickpea cultivars. Methods The virtual plant models were developed using the L-systems formalism, parameterized according to measurements taken on plants at intervals during their development. A quasi-Monte Carlo light-environment model was used to model the effect of chickpea canopy on the development of sowthistle. The chickpea–light environment–sowthistle model (CLES model) captured the hypothesis that the architecture of chickpea plants modifies the light environment inside the canopy and determines sowthistle growth and development pattern. The resulting CLES model was parameterized for different chickpea cultivars (viz. ‘Macarena’, ‘Bumper’, ‘Jimbour’ and ‘99071-1001’) to compare their competitive ability with sowthistle. To validate the CLES model, an experiment was conducted using the same four chickpea cultivars as different treatments with a sowthistle growing under their canopy. Results and Conclusions The growth of sowthistle, both in silico and in glasshouse experiments, was reduced most by ‘99071-1001’, a cultivar with a short phyllochron. The second rank of competitive ability belonged to ‘Macarena’ and ‘Bumper’, while ‘Jimbour’ was the least competitive cultivar. The architecture of virtual chickpea plants modified the light inside the canopy, which influenced the growth and development of the sowthistle plants in response to different cultivars. This is the first time that a virtual plant model of a crop–weed interaction has been developed. This virtual plant model can serve as a platform for a broad range of applications in the study of chickpea–weed interactions and their environment. PMID:18375962

Parameterized isoprene and monoterpene emissions from the boreal forest floor: Implementation into a 1D chemistry-transport model and investigation of the influence on atmospheric chemistry

NASA Astrophysics Data System (ADS)

Mogensen, Ditte; Aaltonen, Hermanni; Aalto, Juho; Bäck, Jaana; Kieloaho, Antti-Jussi; Gierens, Rosa; Smolander, Sampo; Kulmala, Markku; Boy, Michael

2015-04-01

Volatile organic compounds (VOCs) are emitted from the biosphere and can work as precursor gases for aerosol particles that can affect the climate (e.g. Makkonen et al., ACP, 2012). VOC emissions from needles and leaves have gained the most attention, however other parts of the ecosystem also have the ability to emit a vast amount of VOCs. This, often neglected, source can be important e.g. at periods where leaves are absent. Both sources and drivers related to forest floor emission of VOCs are currently limited. It is thought that the sources are mainly due to degradation of organic matter (Isidorov and Jdanova, Chemosphere, 2002), living roots (Asensio et al., Soil Biol. Biochem., 2008) and ground vegetation. The drivers are biotic (e.g. microbes) and abiotic (e.g. temperature and moisture). However, the relative importance of the sources and the drivers individually are currently poorly understood. Further, the relative importance of these factors is highly dependent on the tree species occupying the area of interest. The emission of isoprene and monoterpenes where measured from the boreal forest floor at the SMEAR II station in Southern Finland (Hari and Kulmala, Boreal Env. Res., 2005) during the snow-free period in 2010-2012. We used a dynamic method with 3 automated chambers analyzed by Proton Transfer Reaction - Mass Spectrometer (Aaltonen et al., Plant Soil, 2013). Using this data, we have developed empirical parameterizations for the emission of isoprene and monoterpenes from the forest floor. These parameterizations depends on abiotic factors, however, since the parameterizations are based on field measurements, biotic features are captured. Further, we have used the 1D chemistry-transport model SOSAA (Boy et al., ACP, 2011) to test the seasonal relative importance of inclusion of these parameterizations of the forest floor compared to the canopy crown emissions, on the atmospheric reactivity throughout the canopy.

Aspects of Boreal Forest Hydrology: From Stand to Watershed

NASA Technical Reports Server (NTRS)

Nijssen, B.

2000-01-01

This report evaluates land surface hydrologic processes in the boreal forest using observations collected during the Boreal Ecosystem Atmospheric Study (BOREAS), carried out in the boreal forest of central Canada from 1994 to 1996. Three separate studies, each of which constitutes a journal publication, are included. The first study describes the application of a spatially-distributed hydrologic model, originally developed for mid-latitude forested environments, to selected BOREAS flux measurement sites. Compared to point observations at the flux towers, the model represented energy and moisture fluxes reasonably well, but shortcomings were identified in the soil thermal submodel and the partitioning of evapotranspiration into canopy and subcanopy components. As a first step towards improving this partitioning, the second study develops a new parameterization for transmission of shortwave radiation through boreal forest canopies. The new model accounts for the transmission of diffuse and direct shortwave radiation and accounts for multiple scattering in the canopy and multiple reflections between the canopy layers.

Dispersion of a Passive Scalar Within and Above an Urban Street Network

NASA Astrophysics Data System (ADS)

Goulart, E. V.; Coceal, O.; Belcher, S. E.

2018-03-01

The transport of a passive scalar from a continuous point-source release in an urban street network is studied using direct numerical simulation (DNS). Dispersion through the network is characterized by evaluating horizontal fluxes of scalar within and above the urban canopy and vertical exchange fluxes through the canopy top. The relative magnitude and balance of these fluxes are used to distinguish three different regions relative to the source location: a near-field region, a transition region and a far-field region. The partitioning of each of these fluxes into mean and turbulent parts is computed. It is shown that within the canopy the horizontal turbulent flux in the street network is small, whereas above the canopy it comprises a significant fraction of the total flux. Vertical fluxes through the canopy top are predominantly turbulent. The mean and turbulent fluxes are respectively parametrized in terms of an advection velocity and a detrainment velocity and the parametrization incorporated into a simple box-network model. The model treats the coupled dispersion problem within and above the street network in a unified way and predictions of mean concentrations compare well with the DNS data. This demonstrates the usefulness of the box-network approach for process studies and interpretation of results from more detailed numerical simulations.

A note on the temporal behavior of bucket hydrologies

NASA Technical Reports Server (NTRS)

Suarez, M. J.

1984-01-01

The use of a "canopy' bucket to more accurately represent evapotranspiration over land surfaces is explained. The temporal behavior of the traditional bucket model is compared with one that mimics the effects of interception loss. Results are presented in terms of the spectral response of the parameterization to a hypothetical white noise forcing.

Quantification of the effects of architectural traits on dry mass production and light interception of tomato canopy under different temperature regimes using a dynamic functional–structural plant model

PubMed Central

Chen, Tsu-Wei; Nguyen, Thi My Nguyet; Kahlen, Katrin; Stützel, Hartmut

2014-01-01

There is increasing interest in evaluating the environmental effects on crop architectural traits and yield improvement. However, crop models describing the dynamic changes in canopy structure with environmental conditions and the complex interactions between canopy structure, light interception, and dry mass production are only gradually emerging. Using tomato (Solanum lycopersicum L.) as a model crop, a dynamic functional–structural plant model (FSPM) was constructed, parameterized, and evaluated to analyse the effects of temperature on architectural traits, which strongly influence canopy light interception and shoot dry mass. The FSPM predicted the organ growth, organ size, and shoot dry mass over time with high accuracy (>85%). Analyses of this FSPM showed that, in comparison with the reference canopy, shoot dry mass may be affected by leaf angle by as much as 20%, leaf curvature by up to 7%, the leaf length:width ratio by up to 5%, internode length by up to 9%, and curvature ratios and leaf arrangement by up to 6%. Tomato canopies at low temperature had higher canopy density and were more clumped due to higher leaf area and shorter internodes. Interestingly, dry mass production and light interception of the clumped canopy were more sensitive to changes in architectural traits. The complex interactions between architectural traits, canopy light interception, dry mass production, and environmental conditions can be studied by the dynamic FSPM, which may serve as a tool for designing a canopy structure which is ‘ideal’ in a given environment. PMID:25183746

Evaluation des apports solaires a l'echelle d'un quartier urbain en periode de chauffe selon sa typologie, son orientation et sa latitude dans un contexte de densification de la ville

NASA Astrophysics Data System (ADS)

Chenard, Laurent

Mass urbanization is a major issue for town administrators. Population increase will have an impact on the quality of the environment for citizens. Government will have to take decisions to limit those effects. Green energies are part of the solution to reach fixed goals by the public administration for sustainable development. Passive solar energy is studied in this work in an urban canopy located in five different towns: San Francisco, Montreal, Bordeaux, Lyon and Stockholm. Passive solar energy is calculated in the heating season. Direct and diffuse solar radiation is considered by using the Perez model. Radiosity is not taken into account. Heating demand is calculated by the heating degree day method. Seven urban forms have been created to determine the amount of solar energy entering in every window of the urban canopy while taking into account urban context and forms. Optimal orientation of the canopy shows an increase of 5% of the passive solar radiation from original orientation, 180 degrees rotation from first orientation straight south. This value goes lower when stories are added to the urban context. A rotation of 90 degrees from the first orientation shows a decrease of 6 to 15% in solar passive gain. Densification of the urban canopy by adding stories to the buildings results in a loss up to 65% of the solar gain for the first story. It is showed that solar passive energy has a low ratio of 5% for space heating for old buildings, 1960 constructions. Today's buildings have a difference between passive solar energy and heating demand of 10 to 75% depending on the model and location.

Atmospheric Inputs of Nitrogen, Carbon, and Phosphorus across an Urban Area: Unaccounted Fluxes and Canopy Influences

NASA Astrophysics Data System (ADS)

Decina, Stephen M.; Templer, Pamela H.; Hutyra, Lucy R.

2018-02-01

Rates of atmospheric deposition are declining across the United States, yet urban areas remain hotspots of atmospheric deposition. While past studies show elevated rates of inorganic nitrogen (N) deposition in cities, less is known about atmospheric inputs of organic N, organic carbon (C), and organic and inorganic phosphorus (P), all of which can affect ecosystem processes, water quality, and air quality. Further, the effect of the tree canopy on amounts and forms of nutrients reaching urban ground surfaces is not well-characterized. We measured growing season rates of total N, organic C, and total P in bulk atmospheric inputs, throughfall, and soil solution around the greater Boston area. We found that organic N constitutes a third of total N inputs, organic C inputs are comparable to rural inputs, and inorganic P inputs are 1.2 times higher than those in sewage effluent. Atmospheric inputs are enhanced two-to-eight times in late spring and are elevated beneath tree canopies, suggesting that trees augment atmospheric inputs to ground surfaces. Additionally, throughfall inputs may directly enter runoff when trees extend above impervious surfaces, as is the case with 26.1% of Boston's tree canopy. Our results indicate that the urban atmosphere is a significant source of elemental inputs that may impact urban ecosystems and efforts to improve water quality, particularly in terms of P. Further, as cities create policies encouraging tree planting to provide ecosystem services, locating trees above permeable surfaces to reduce runoff nutrient loads may be essential to managing urban biogeochemical cycling and water quality.

Emerald ash borer and the urban forest: Changes in landslide potential due to canopy loss scenarios in the City of Pittsburgh, PA.

PubMed

Pfeil-McCullough, Erin; Bain, Daniel J; Bergman, Jeffery; Crumrine, Danielle

2015-12-01

Emerald ash borer is expected to kill thousands of ash trees in the eastern U.S. This research develops tools to predict the effect of ash tree loss from the urban canopy on landslide susceptibility in Pittsburgh, PA. A spatial model was built using the SINMAP (Stability INdex MAPping) model coupled with spatially explicit scenarios of tree loss (0%, 25%, 50%, and 75% loss of ash trees from the canopy). Ash spatial distributions were estimated via Monte Carlo methods and available vegetation plot data. Ash trees are most prevalent on steeper slopes, likely due to urban development patterns. Therefore, ash loss disproportionately increases hillslope instability. A 75% loss of ash resulted in roughly 800 new potential landslide initiation locations. Sensitivity testing reveals that variations in rainfall rates, and friction angles produce minor changes to model results relative to the magnitude of parameter variation, but reveal high model sensitivity to soil density and root cohesion values. The model predictions demonstrate the importance of large canopy species to urban hillslope stability, particularly on steep slopes and in areas where soils tend to retain water. To improve instability predictions, better characterization of urban soils, particularly spatial patterns of compaction and species specific root cohesion is necessary. The modeling framework developed in this research will enhance assessment of changes in landslide risk due to tree mortality, improving our ability to design economically and ecologically sustainable urban systems. Copyright © 2015 Elsevier B.V. All rights reserved.

A model of canopy photosynthesis incorporating protein distribution through the canopy and its acclimation to light, temperature and CO2

PubMed Central

Johnson, Ian R.; Thornley, John H. M.; Frantz, Jonathan M.; Bugbee, Bruce

2010-01-01

Background and Aims The distribution of photosynthetic enzymes, or nitrogen, through the canopy affects canopy photosynthesis, as well as plant quality and nitrogen demand. Most canopy photosynthesis models assume an exponential distribution of nitrogen, or protein, through the canopy, although this is rarely consistent with experimental observation. Previous optimization schemes to derive the nitrogen distribution through the canopy generally focus on the distribution of a fixed amount of total nitrogen, which fails to account for the variation in both the actual quantity of nitrogen in response to environmental conditions and the interaction of photosynthesis and respiration at similar levels of complexity. Model A model of canopy photosynthesis is presented for C3 and C4 canopies that considers a balanced approach between photosynthesis and respiration as well as plant carbon partitioning. Protein distribution is related to irradiance in the canopy by a flexible equation for which the exponential distribution is a special case. The model is designed to be simple to parameterize for crop, pasture and ecosystem studies. The amount and distribution of protein that maximizes canopy net photosynthesis is calculated. Key Results The optimum protein distribution is not exponential, but is quite linear near the top of the canopy, which is consistent with experimental observations. The overall concentration within the canopy is dependent on environmental conditions, including the distribution of direct and diffuse components of irradiance. Conclusions The widely used exponential distribution of nitrogen or protein through the canopy is generally inappropriate. The model derives the optimum distribution with characteristics that are consistent with observation, so overcoming limitations of using the exponential distribution. Although canopies may not always operate at an optimum, optimization analysis provides valuable insight into plant acclimation to environmental conditions. Protein distribution has implications for the prediction of carbon assimilation, plant quality and nitrogen demand. PMID:20861273

The study of ozone variations in the Las Vegas metropolitan area using remote sensing information and ground observations

USGS Publications Warehouse

Xian, G.; Crane, M.

2006-01-01

Urban development in the Las Vegas Valley, Nevada, has grown rapidly in the past fifty years. Associated with this growth has been a change in landscape from natural cover types to developed urban land mixed with planned vegetation canopy throughout in the metropolitan area. Air quality in the Las Vegas Valley has been affected by increases in anthropogenic emissions and concentrations of carbon monoxide, ozone, and criteria pollutants of particular matter. Ozone concentration in the region is generally influenced by synoptic and mesoscale meteorological conditions, as well as regional transport of pollutants from the western side of Las Vegas. Local influences from ground-level nitrogen oxide emissions and vegetation canopy coverage also affect ozone concentration. Multi-year observational data collected by a network of local air monitoring stations in Clark County, Nevada, indicate that ozone maximums develop in May and June, while minimums exist primarily from November to February. Ozone concentrations are high on the west and northwest sides of the valley. A nighttime ozone reduction in the urban area characterizes the heterogeneous features of spatial distribution for average ozone levels in the Las Vegas urban area. The urban vegetation canopy has a locally positive effect by reducing ozone in urban areas. Decreased ozone levels associated with increased urban development density suggests that the highest ozone concentrations are associated with medium- to low-density urban development in Las Vegas.

Parameter Estimation and Sensitivity Analysis of an Urban Surface Energy Balance Parameterization at a Tropical Suburban Site

NASA Astrophysics Data System (ADS)

Harshan, S.; Roth, M.; Velasco, E.

2014-12-01

Forecasting of the urban weather and climate is of great importance as our cities become more populated and considering the combined effects of global warming and local land use changes which make urban inhabitants more vulnerable to e.g. heat waves and flash floods. In meso/global scale models, urban parameterization schemes are used to represent the urban effects. However, these schemes require a large set of input parameters related to urban morphological and thermal properties. Obtaining all these parameters through direct measurements are usually not feasible. A number of studies have reported on parameter estimation and sensitivity analysis to adjust and determine the most influential parameters for land surface schemes in non-urban areas. Similar work for urban areas is scarce, in particular studies on urban parameterization schemes in tropical cities have so far not been reported. In order to address above issues, the town energy balance (TEB) urban parameterization scheme (part of the SURFEX land surface modeling system) was subjected to a sensitivity and optimization/parameter estimation experiment at a suburban site in, tropical Singapore. The sensitivity analysis was carried out as a screening test to identify the most sensitive or influential parameters. Thereafter, an optimization/parameter estimation experiment was performed to calibrate the input parameter. The sensitivity experiment was based on the "improved Sobol's global variance decomposition method" . The analysis showed that parameters related to road, roof and soil moisture have significant influence on the performance of the model. The optimization/parameter estimation experiment was performed using the AMALGM (a multi-algorithm genetically adaptive multi-objective method) evolutionary algorithm. The experiment showed a remarkable improvement compared to the simulations using the default parameter set. The calibrated parameters from this optimization experiment can be used for further model validation studies to identify inherent deficiencies in model physics.

Increasing of Urban Radiation due to Climate Change and Reduction Strategy using Vegetation

NASA Astrophysics Data System (ADS)

Park, C.; Lee, D.; Heo, H. K.; Ahn, S.

2017-12-01

Urban Heat Island (UHI) which means urban air temperature is higher than suburban area is one of the most important environmental issues in Urban. High density of buildings and high ratio of impervious surfaces increases the radiation fluxes in urban canopy. Furthermore, climate change is expected to make UHI even more seriously in the future. Increased irradiation and air temperature cause high amount of short wave and long wave radiation, respectively. This increases net radiation negatively affects heat condition of pedestrian. UHI threatens citizen's health by increasing violence and heat related diseases. For this reason, understanding how much urban radiation will increase in the future, and exploring radiation reduction strategies is important for reducing UHI. In this research, we aim to reveal how the radiation flux in the urban canyon will change as the climate change and determine how much of urban vegetation will be needed to cover this degradation. The study area is a commercial district in Seoul where highly populated area. Due to the high density of buildings and lack of urban vegetation, this area has a poor thermal condition in summer. In this research, we simulate the radiation flux on the ground using multi-layer urban canopy model. Unlike conventionally used urban canopy model to simulate radiation transfer using vertically single layer, the multi-layer model we used here, enables to consider the vertical heterogeneous of buildings and urban vegetation. As a result, net radiation of urban ground will be increase 2.1 W/m² in the 2050s and 2.7 W/m² in the 2100s. And to prevent the increase of radiation, it is revealed that the urban vegetation should by increased by 10%. This research will be valuable in establishing greening planning as a strategy to reduce UHI effect.

Pragmatic hydraulic theory predicts stomatal responses to climatic water deficits.

PubMed

Sperry, John S; Wang, Yujie; Wolfe, Brett T; Mackay, D Scott; Anderegg, William R L; McDowell, Nate G; Pockman, William T

2016-11-01

Ecosystem models have difficulty predicting plant drought responses, partially from uncertainty in the stomatal response to water deficits in soil and atmosphere. We evaluate a 'supply-demand' theory for water-limited stomatal behavior that avoids the typical scaffold of empirical response functions. The premise is that canopy water demand is regulated in proportion to threat to supply posed by xylem cavitation and soil drying. The theory was implemented in a trait-based soil-plant-atmosphere model. The model predicted canopy transpiration (E), canopy diffusive conductance (G), and canopy xylem pressure (P canopy ) from soil water potential (P soil ) and vapor pressure deficit (D). Modeled responses to D and P soil were consistent with empirical response functions, but controlling parameters were hydraulic traits rather than coefficients. Maximum hydraulic and diffusive conductances and vulnerability to loss in hydraulic conductance dictated stomatal sensitivity and hence the iso- to anisohydric spectrum of regulation. The model matched wide fluctuations in G and P canopy across nine data sets from seasonally dry tropical forest and piñon-juniper woodland with < 26% mean error. Promising initial performance suggests the theory could be useful in improving ecosystem models. Better understanding of the variation in hydraulic properties along the root-stem-leaf continuum will simplify parameterization. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

Source diagnostics of polycyclic aromatic hydrocarbons in urban road runoff, dust, rain and canopy throughfall.

PubMed

Zhang, Wei; Zhang, Shucai; Wan, Chao; Yue, Dapan; Ye, Youbin; Wang, Xuejun

2008-06-01

Diagnostic ratios and multivariate analysis were utilized to apportion polycyclic aromatic hydrocarbon (PAH) sources for road runoff, road dust, rain and canopy throughfall based on samples collected in an urban area of Beijing, China. Three sampling sites representing vehicle lane, bicycle lane and branch road were selected. For road runoff and road dust, vehicular emission and coal combustion were identified as major sources, and the source contributions varied among the sampling sites. For rain, three principal components were apportioned representing coal/oil combustion (54%), vehicular emission (34%) and coking (12%). For canopy throughfall, vehicular emission (56%), coal combustion (30%) and oil combustion (14%) were identified as major sources. Overall, the PAH's source for road runoff mainly reflected that for road dust. Despite site-specific sources, the findings at the study area provided a general picture of PAHs sources for the road runoff system in urban area of Beijing.

Analysis of the effect of evergreen and deciduous trees on urban nitrogen dioxide levels in the U.S. using land-use regression

NASA Astrophysics Data System (ADS)

Rao, M.; George, L. A.

2012-12-01

Nitrogen dioxide (NO2), an atmospheric pollutant generated primarily by anthropogenic combustion processes, is typically found at higher concentrations in urban areas compared to non-urbanized environments. Elevated NO2 levels have multiple ecosystem effects at different spatial scales. At the local scale, elevated levels affect human health directly and through the formation of secondary pollutants such as ozone and aerosols; at the regional scale secondary pollutants such as nitric acid and organic nitrates have deleterious effects on non-urbanized areas; and, at the global scale, nitrogen oxide emissions significantly alter the natural biogeochemical nitrogen cycle. As cities globally become larger and larger sources of nitrogen oxide emissions, it is important to assess possible mitigation strategies to reduce the impact of emissions locally, regionally and globally. In this study, we build a national land-use regression (LUR) model to compare the impacts of deciduous and evergreen trees on urban NO2 levels in the United States. We use the EPA monitoring network values of NO2 levels for 2006, the 2006 NLCD tree canopy data for deciduous and evergreen canopies, and the US Census Bureau's TIGER shapefiles for roads, railroads, impervious area & population density as proxies for NO2 sources on-road traffic, railroad traffic, off-road and area sources respectively. Our preliminary LUR model corroborates previous LUR studies showing that the presence of trees is associated with reduced urban NO2 levels. Additionally, our model indicates that deciduous and evergreen trees reduce NO2 to different extents, and that the amount of NO2 reduced varies seasonally. The model indicates that every square kilometer of deciduous canopy within a 2km buffer is associated with a reduction in ambient NO2 levels of 0.64 ppb in summer and 0.46ppb in winter. Similarly, every square kilometer of evergreen tree canopy within a 2 km buffer is associated with a reduction in ambient NO2 by 0.53 ppb in summer and 0.84 ppb in winter. Thus, the model indicates that deciduous trees are associated with a 30% smaller reduction in NO2 in winter as compared to summer, while evergreens are associated with a 60% increase in the reduction of NO2 in winter, for every square kilometer of deciduous or evergreen canopy within a 2 km buffer. Leaf- and local canopy-level studies have shown that trees are a sink for urban NO2 through deposition as well as stomatal and cuticular uptake. The winter time versus summer time effects suggest that leaf-level deposition may not be the only uptake mechanism and points to the need for a more holistic analysis of tree and canopy-level deposition for urban air pollution models. Since deposition velocities for NO2 vary by tree species, the reduction may also vary by species. These findings have implications for designing cities to reduce the impact of air pollution.

High-Resolution Three-Dimensional Structural Data Quantify the Impact of Photoinhibition on Long-Term Carbon Gain in Wheat Canopies in the Field1[OPEN

PubMed Central

Burgess, Alexandra J.; Retkute, Renata; Pound, Michael P.; Foulkes, John; Preston, Simon P.; Jensen, Oliver E.; Pridmore, Tony P.; Murchie, Erik H.

2015-01-01

Photoinhibition reduces photosynthetic productivity; however, it is difficult to quantify accurately in complex canopies partly because of a lack of high-resolution structural data on plant canopy architecture, which determines complex fluctuations of light in space and time. Here, we evaluate the effects of photoinhibition on long-term carbon gain (over 1 d) in three different wheat (Triticum aestivum) lines, which are architecturally diverse. We use a unique method for accurate digital three-dimensional reconstruction of canopies growing in the field. The reconstruction method captures unique architectural differences between lines, such as leaf angle, curvature, and leaf density, thus providing a sensitive method of evaluating the productivity of actual canopy structures that previously were difficult or impossible to obtain. We show that complex data on light distribution can be automatically obtained without conventional manual measurements. We use a mathematical model of photosynthesis parameterized by field data consisting of chlorophyll fluorescence, light response curves of carbon dioxide assimilation, and manual confirmation of canopy architecture and light attenuation. Model simulations show that photoinhibition alone can result in substantial reduction in carbon gain, but this is highly dependent on exact canopy architecture and the diurnal dynamics of photoinhibition. The use of such highly realistic canopy reconstructions also allows us to conclude that even a moderate change in leaf angle in upper layers of the wheat canopy led to a large increase in the number of leaves in a severely light-limited state. PMID:26282240

Impact of Land Use/Land Cover Conditions on WRF Model Evaluation for Heat Island Assessment

NASA Astrophysics Data System (ADS)

Bhati, S.; Mohan, M.

2017-12-01

Urban heat island effect has been assessed using Weather Research and Forecasting model (WRF v3.5) focusing on air temperature and surface skin temperature in the sub-tropical urban Indian megacity of Delhi. Impact of urbanization related changes in land use/land cover (LULC) on model outputs has been analyzed. Four simulations have been carried out with different types of LULC data viz. (1) USGS , (2) MODIS, (3) user-modified USGS and (4) user modified land use data coupled with urban canopy model (UCM) for incorporation of canopy features. Heat island intensities have been estimated based on these simulations and subsequently compared with those derived from in-situ and satellite observations. There is a significant improvement in model performance with modification of LULC and inclusion of UCM. Overall, RMSEs for near surface temperature improved from 6.3°C to 3.9°C and index of agreement for mean urban heat island intensities (UHI) improved from 0.4 to 0.7 with modified land use coupled with UCM. In general, model is able to capture the magnitude of UHI as well as high UHI zones well. The study highlights the importance of appropriate and updated representation of landuse-landcover and urban canopies for improving predictive capabilities of the mesoscale models.

Vegetation canopy cover effects on sediment erosion processes in the upper Colorado River Basin mancos shale formation, Price, Utah

USDA-ARS?s Scientific Manuscript database

This study provides new parameterizations for applying the Rangeland Hydrology and Erosion Model (RHEM) on the highly erosive, rangeland saline soils of the Mancos Shale formation in the Price-San Rafael River Basin in east central Utah. Calibrated hydrologic parameters (Kss and K') values are gener...

Canopy carbon net assimilation of an urban, naturally assembled brownfield forest

NASA Astrophysics Data System (ADS)

Schafer, K. V.; Wadhwa, S.; Tripathee, R.; Gallagher, F. J.

2010-12-01

In this study, we have been investigating an urban brownfield at Liberty State Park that has been abandoned approximately for 40 years. Natural colonization has taken place that allowed a pioneer forest to grow with primarily Betula populifera and Populus spec. Despite soil metal contamination this urban forest exhibits moderate annual productivity and serves as a carbon sink. Diameters at breast height (DBH, 1.35 m above ground) of all trees in a study plot were measured. Aboveground biomass equations were determined for both species through destructive sampling. Aboveground net primary production was about 770 gC m-2 a-1 in 2009. Canopy net assimilation (AnC) was modeled with the canopy conductance constrained assimilation (4CA) model using measured sapflux derived conductance and photosynthetic parameters measured with a LICOR 6400. Annual AnC in 2009 was approximately 1500 gC m-2 a-1 thus with a partitioning of biomass and respiration in the same range of most natural forest with less anthropogenic induced stress. Urban brownfields thus can serve as C sinks and provide phytostabilization of contaminants.

Modeling the energy balance in Marseille: Sensitivity to roughness length parameterizations and thermal admittance

NASA Astrophysics Data System (ADS)

Demuzere, M.; De Ridder, K.; van Lipzig, N. P. M.

2008-08-01

During the ESCOMPTE campaign (Experience sur Site pour COntraindre les Modeles de Pollution atmospherique et de Transport d'Emissions), a 4-day intensive observation period was selected to evaluate the Advanced Regional Prediction System (ARPS), a nonhydrostatic meteorological mesoscale model that was optimized with a parameterization for thermal roughness length to better represent urban surfaces. The evaluation shows that the ARPS model is able to correctly reproduce temperature, wind speed, and direction for one urban and two rural measurements stations. Furthermore, simulated heat fluxes show good agreement compared to the observations, although simulated sensible heat fluxes were initially too low for the urban stations. In order to improve the latter, different roughness length parameterization schemes were tested, combined with various thermal admittance values. This sensitivity study showed that the Zilitinkevich scheme combined with and intermediate value of thermal admittance performs best.

The influence of tree traits and storm event characteristics on stemflow production from isolated deciduous trees in an urban park

NASA Astrophysics Data System (ADS)

Carlyle-Moses, D. E.; Schooling, J. T.

2014-12-01

Urban tree canopy processes affect the volume and biogeochemistry of inputs to the hydrological cycle in cities. We studied stemflow from 37 isolated deciduous trees in an urban park in Kamloops, British Columbia which has a semi-arid climate dominated by small precipitation events. Precipitation and stemflow were measured on an event basis from June 12, 2012 to November 3, 2013. To clarify the effect of canopy traits on stemflow thresholds, rates, yields, percent, and funneling ratios, we analyzed branch angles, bark roughness, tree size, cover, leaf size, and branch and leader counts. High branch angles promoted stemflow in all trees, while bark roughness influenced stemflow differently for single- and multi-leader trees. The association between stemflow and numerous leaders deserves further study. Columnar-form trees often partitioned a large percentage of precipitation into stemflow, with event-scale values as high as 27.9 % recorded for an Armstrong Freeman Maple (Acer x freemanii 'Armstrong'). Under growing-season conditions funneling ratios as high as 196.9 were derived for an American Beech (Fagus grandifolia) individual. Among meteorological variables, rain depth was strongly correlated with stemflow yields; intra-storm break duration, rainfall intensity, rainfall inclination, wind speed, and vapour pressure deficit also played roles. Greater stemflow was associated with leafless canopies and with rain or mixed events versus snow. Results can inform climate-sensitive selection and siting of urban trees towards integrated rainwater management. For example, previous studies suggest that the reduction in storm-water generation by urban trees is accomplished through canopy interception loss alone. However, trees that partition large quantities of precipitation canopy-drainage as stemflow to the base of their trunks, where it has the potential to infiltrate into the soil media rather than fall on impervious surfaces as throughfall, may assist in reducing stormwater flow.

Edge-to-Stem Variability in Wet-Canopy Evaporation From an Urban Tree Row

NASA Astrophysics Data System (ADS)

Van Stan, John T.; Norman, Zachary; Meghoo, Adrian; Friesen, Jan; Hildebrandt, Anke; Côté, Jean-François; Underwood, S. Jeffrey; Maldonado, Gustavo

2017-11-01

Evaporation from wet-canopy (E_C) and stem (E_S) surfaces during rainfall represents a significant portion of municipal-to-global scale hydrologic cycles. For urban ecosystems, E_C and E_S dynamics play valuable roles in stormwater management. Despite this, canopy-interception loss studies typically ignore crown-scale variability in E_C and assume (with few indirect data) that E_S is generally {<}2% of total wet-canopy evaporation. We test these common assumptions for the first time with a spatially-distributed network of in-canopy meteorological monitoring and 45 surface temperature sensors in an urban Pinus elliottii tree row to estimate E_C and E_S under the assumption that crown surfaces behave as "wet bulbs". From December 2015 through July 2016, 33 saturated crown periods (195 h of 5-min observations) were isolated from storms for determination of 5-min evaporation rates ranging from negligible to 0.67 mm h^{-1}. Mean E_S (0.10 mm h^{-1}) was significantly lower (p < 0.01) than mean E_C (0.16 mm h^{-1}). But, E_S values often equalled E_C and, when scaled to trunk area using terrestrial lidar, accounted for 8-13% (inter-quartile range) of total wet-crown evaporation (E_S+E_C scaled to surface area). E_S contributions to total wet-crown evaporation maximized at 33%, showing a general underestimate (by 2-17 times) of this quantity in the literature. Moreover, results suggest wet-crown evaporation from urban tree rows can be adequately estimated by simply assuming saturated tree surfaces behave as wet bulbs, avoiding problematic assumptions associated with other physically-based methods.

On the added value of WUDAPT for Urban Climate Modelling

NASA Astrophysics Data System (ADS)

Brousse, Oscar; Martilli, Alberto; Mills, Gerald; Bechtel, Benjamin; Hammerberg, Kris; Demuzere, Matthias; Wouters, Hendrik; Van Lipzig, Nicole; Ren, Chao; Feddema, Johannes J.; Masson, Valéry; Ching, Jason

2017-04-01

Over half of the planet's population now live in cities and is expected to grow up to 65% by 2050 (United Nations, 2014), most of whom will actually occupy new emerging cities of the global South. Cities' impact on climate is known to be a key driver of environmental change (IPCC, 2014) and has been studied for decades now (Howard, 1875). Still very little is known about our cities' structure around the world, preventing urban climate simulations to be done and hence guidance to be provided for mitigation. Assessing the need to bridge the urban knowledge gap for urban climate modelling perspectives, the World Urban Database and Access Portal Tool - WUDAPT - project (Ching et al., 2015; Mills et al., 2015) developed an innovative technique to map cities globally rapidly and freely. The framework established by Bechtel and Daneke (2012) derives Local Climate Zones (Stewart and Oke, 2012) city maps out of LANDSAT 8 OLI-TIRS imagery (Bechtel et al., 2015) through a supervised classification by a Random Forest Classification algorithm (Breiman, 2001). The first attempt to implement Local Climate Zones (LCZ) out of the WUDAPT product within a major climate model was carried out by Brousse et al. (2016) over Madrid, Spain. This study proved the applicability of LCZs as an enhanced urban parameterization within the WRF model (Chen et al. 2011) employing the urban canopy model BEP-BEM (Martilli, 2002; Salamanca et al., 2010), using the averaged values of the morphological and physical parameters' ranges proposed by Stewart and Oke (2012). Other studies have now used the Local Climate Zones for urban climate modelling purposes (Alexander et al., 2016; Wouters et al. 2016; Hammerberg et al., 2017; Brousse et al., 2017) and demonstrated the added value of the WUDAPT dataset. As urban data accessibility is one of the major challenge for simulations in emerging countries, this presentation will show results of simulations using LCZs and the capacity of the WUDAPT framework to be of high relevancy in multiple regions of the world, such as Africa or Asia.

Quantifying widespread canopy cover decline through the course of a beetle kill epidemic in Colorado with remote sensing of snow

NASA Astrophysics Data System (ADS)

Baker, E. H.; Raleigh, M. S.; Molotch, N. P.

2014-12-01

Since the mid-1990s, outbreaks of aggressive bark beetle species have caused extensive forest morality across 600,000 km2 of North-American forests, killing over 17,800 km2 of forest in Colorado alone. This mortality has resulted in a widespread, spatially heterogeneous decline of forest canopies, which in turn exerts strong controls on the accumulation and melt of the snowpack. In the Western United States, where approximately 70-80% of total annual runoff originates as mountain snowmelt, it is important to monitor and quantify changes in forest canopy in snow-dominated catchments. To quantify annual values of forest canopy cover, this research develops a metric from time series of daily fractional snow covered area (FSCA) from NASA's Moderate Resolution Imaging Spectroradiometer (MODIS) snow covered area and grain size (MODSCAG) algorithm. In areas where soil and rock are completely snow-covered, a land pixel is composed only of forest canopy and snow. Following a snowfall event, FSCA initially rises rapidly, as snow is intercepted in the canopy, and then declines, as snow unloads from the canopy. The lower of these local minima form a threshold representative of snow-free canopy conditions, which serves as a spatially explicit metric of forest canopy. Investigation of a site in southern Colorado with over 40% spruce beetle mortality shows a statistically significant decrease of canopy cover, from 76 (±4)% pre-infestation to 55 (±8)% post-infestation (t=-5.1, p<0.01). Additionally, this yearly parameterization of forest canopy is well correlated (ρ=0.76, p<0.01) with an independent product of yearly crown mortality derived from U.S. Forest Service Aerial Detection Surveys. Future work will examine this relationship across varied ecologic settings and geographic locations, and incorporate field measurements of species-specific canopy change after beetle kill.

Observations of the scale-dependent turbulence and evaluation of the flux–gradient relationship for sensible heat for a closed Douglas-fir canopy in very weak wind conditions

DOE PAGES

Vickers, D.; Thomas, C. K.

2014-09-16

Observations of the scale-dependent turbulent fluxes, variances, and the bulk transfer parameterization for sensible heat above, within, and beneath a tall closed Douglas-fir canopy in very weak winds are examined. The daytime sub-canopy vertical velocity spectra exhibit a double-peak structure with peaks at timescales of 0.8 s and 51.2 s. A double-peak structure is also observed in the daytime sub-canopy heat flux co-spectra. The daytime momentum flux co-spectra in the upper bole space and in the sub-canopy are characterized by a relatively large cross-wind component, likely due to the extremely light and variable winds, such that the definition of amore » mean wind direction, and subsequent partitioning of the momentum flux into along- and cross-wind components, has little physical meaning. Positive values of both momentum flux components in the sub-canopy contribute to upward transfer of momentum, consistent with the observed sub-canopy secondary wind speed maximum. For the smallest resolved scales in the canopy at nighttime, we find increasing vertical velocity variance with decreasing timescale, consistent with very small eddies possibly generated by wake shedding from the canopy elements that transport momentum, but not heat. Unusually large values of the velocity aspect ratio within the canopy were observed, consistent with enhanced suppression of the horizontal wind components compared to the vertical by the very dense canopy. The flux–gradient approach for sensible heat flux is found to be valid for the sub-canopy and above-canopy layers when considered separately in spite of the very small fluxes on the order of a few W m −2 in the sub-canopy. However, single-source approaches that ignore the canopy fail because they make the heat flux appear to be counter-gradient when in fact it is aligned with the local temperature gradient in both the sub-canopy and above-canopy layers. While sub-canopy Stanton numbers agreed well with values typically reported in the literature, our estimates for the above-canopy Stanton number were much larger, which likely leads to underestimated modeled sensible heat fluxes above dark warm closed canopies.« less

Observations of the scale-dependent turbulence and evaluation of the flux–gradient relationship for sensible heat for a closed Douglas-fir canopy in very weak wind conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vickers, D.; Thomas, C. K.

Observations of the scale-dependent turbulent fluxes, variances, and the bulk transfer parameterization for sensible heat above, within, and beneath a tall closed Douglas-fir canopy in very weak winds are examined. The daytime sub-canopy vertical velocity spectra exhibit a double-peak structure with peaks at timescales of 0.8 s and 51.2 s. A double-peak structure is also observed in the daytime sub-canopy heat flux co-spectra. The daytime momentum flux co-spectra in the upper bole space and in the sub-canopy are characterized by a relatively large cross-wind component, likely due to the extremely light and variable winds, such that the definition of amore » mean wind direction, and subsequent partitioning of the momentum flux into along- and cross-wind components, has little physical meaning. Positive values of both momentum flux components in the sub-canopy contribute to upward transfer of momentum, consistent with the observed sub-canopy secondary wind speed maximum. For the smallest resolved scales in the canopy at nighttime, we find increasing vertical velocity variance with decreasing timescale, consistent with very small eddies possibly generated by wake shedding from the canopy elements that transport momentum, but not heat. Unusually large values of the velocity aspect ratio within the canopy were observed, consistent with enhanced suppression of the horizontal wind components compared to the vertical by the very dense canopy. The flux–gradient approach for sensible heat flux is found to be valid for the sub-canopy and above-canopy layers when considered separately in spite of the very small fluxes on the order of a few W m −2 in the sub-canopy. However, single-source approaches that ignore the canopy fail because they make the heat flux appear to be counter-gradient when in fact it is aligned with the local temperature gradient in both the sub-canopy and above-canopy layers. While sub-canopy Stanton numbers agreed well with values typically reported in the literature, our estimates for the above-canopy Stanton number were much larger, which likely leads to underestimated modeled sensible heat fluxes above dark warm closed canopies.« less

A Numerical Study of Atmospheric Perturbations Induced by Heat From a Wildland Fire: Sensitivity to Vertical Canopy Structure and Heat Source Strength

NASA Astrophysics Data System (ADS)

Kiefer, Michael T.; Zhong, Shiyuan; Heilman, Warren E.; Charney, Joseph J.; Bian, Xindi

2018-03-01

An improved understanding of atmospheric perturbations within and above a forest during a wildland fire has relevance to many aspects of wildland fires including fire spread, smoke transport and dispersion, and tree mortality. In this study, the ARPS-CANOPY model, a version of the Advanced Regional Prediction System (ARPS) model with a canopy parameterization, is utilized in a series of idealized numerical experiments to investigate the influence of vertical canopy structure on the atmospheric response to a stationary sensible heat flux at the ground ("fire heat flux"), broadly consistent in magnitude with the sensible heat flux from a low-intensity surface fire. Five vertical canopy structures are combined with five fire heat flux magnitudes to yield a matrix of 25 simulations. Analyses of the fire-heat-flux-perturbed u component of the wind, vertical velocity, kinetic energy, and temperature show that the spatial pattern and magnitude of the perturbations are sensitive to vertical canopy structure. Both vertical velocity and kinetic energy exhibit an increasing trend with increasing fire heat flux that is stronger for cases with some amount of overstory vegetation than cases with exclusively understory vegetation. A weaker trend in cases with exclusively understory vegetation indicates a damping of the atmospheric response to the sensible heat from a surface fire when vegetation is most concentrated near the surface. More generally, the results presented in this study suggest that canopy morphology should be considered when applying the results of a fire-atmosphere interaction study conducted in one type of forest to other forests with different canopy structures.

Feedbacks between Air-Quality, Meteorology, and the Forest Environment

NASA Astrophysics Data System (ADS)

Makar, Paul; Akingunola, Ayodeji; Stroud, Craig; Zhang, Junhua; Gong, Wanmin; Moran, Michael; Zheng, Qiong; Brook, Jeffrey; Sills, David

2017-04-01

The outcome of air quality forecasts depend in part on how the local environment surrounding the emissions regions influences chemical reaction rates and transport from those regions to the larger spatial scales. Forested areas alter atmospheric chemistry through reducing photolysis rates and vertical diffusivities within the forest canopy. The emitted pollutants, and their reaction products, are in turn capable of altering meteorology, through the well-known direct and indirect effects of particulate matter on radiative transfer. The combination of these factors was examined using version 2 of the Global Environmental Multiscale - Modelling Air-quality and CHemistry (GEM-MACH) on-line air pollution model. The model configuration used for this study included 12 aerosol size bins, eight aerosol species, homogeneous core Mie scattering, the Milbrandt-Yao two-moment cloud microphysics scheme with cloud condensation nuclei generated from model aerosols using the scheme of Abdul-Razzak and Ghan, and a new parameterization for forest canopy shading and turbulence. The model was nested to 2.5km resolution for a domain encompassing the lower Great Lakes, for simulations of a period in August of 2015 during the Pan American Games, held in Toronto, Canada. Four scenarios were carried out: (1) a "Base Case" scenario (the original model, in which coupling between chemistry and weather is not permitted; instead, the meteorological model's internal climatologies for aerosol optical and cloud condensation properties are used for direct and indirect effect calculations); (2) a "Feedback" scenario (the aerosol properties were derived from the internally simulated chemistry, and coupled to the meteorological model's radiative transfer and cloud formation modules); (3) a "Forest" scenario (canopy shading and turbulence were added to the Base Case); (4) a "Combined" scenario (including both direct and indirect effect coupling between meteorology and chemistry, as well as the forest canopy parameterization). The simulations suggest that the feedbacks between simulated aerosols and meteorology may strengthen the existing lake breeze circulation, modifying the resulting meteorological and air-quality forecasts, while the forest canopy's influence may extend throughout the planetary boundary layer, and may also influence the weather. The simulations will be compared to available observations, in order to determine their relative impact on model performance.

A Three-dimensional Statistical Reconstruction Model of Grapevine (Vitis vinifera) Simulating Canopy Structure Variability within and between Cultivar/Training System Pairs

PubMed Central

Louarn, Gaëtan; Lecoeur, Jérémie; Lebon, Eric

2008-01-01

Background and Aims In grapevine, canopy-structure-related variations in light interception and distribution affect productivity, yield and the quality of the harvested product. A simple statistical model for reconstructing three-dimensional (3D) canopy structures for various cultivar–training system (C × T) pairs has been implemented with special attention paid to balance the time required for model parameterization and accuracy of the representations from organ to stand scales. Such an approach particularly aims at overcoming the weak integration of interplant variability using the usual direct 3D measurement methods. Model This model is original in combining a turbid-medium-like envelope enclosing the volume occupied by vine shoots with the use of discrete geometric polygons representing leaves randomly located within this volume to represent plant structure. Reconstruction rules were adapted to capture the main determinants of grapevine shoot architecture and their variability. Using a simplified set of parameters, it was possible to describe (1) the 3D path of the main shoot, (2) the volume occupied by the foliage around this path and (3) the orientation of individual leaf surfaces. Model parameterization (estimation of the probability distribution for each parameter) was carried out for eight contrasting C × T pairs. Key Results and Conclusions The parameter values obtained in each situation were consistent with our knowledge of grapevine architecture. Quantitative assessments for the generated virtual scenes were carried out at the canopy and plant scales. Light interception efficiency and local variations of light transmittance within and between experimental plots were correctly simulated for all canopies studied. The approach predicted these key ecophysiological variables significantly more accurately than the classical complete digitization method with a limited number of plants. In addition, this model accurately reproduced the characteristics of a wide range of individual digitized plants. Simulated leaf area density and the distribution of light interception among leaves were consistent with measurements. However, at the level of individual organs, the model tended to underestimate light interception. PMID:18202006

Observing the Vertical Dimensions of Singapore's Urban Heat Island

NASA Astrophysics Data System (ADS)

Chow, W. T. L.; Ho, D. X. Q.

2015-12-01

In numerous cities, measurements of urban warmth in most urban heat island (UHI) studies are generally constrained towards surface or near-surface (<2 m above ground) levels across horizontal variations in land use and land cover. However, there has been hitherto limited attention towards the measurement of vertical temperature profiles extending from the urban surface through to the urban boundary layer. Knowledge of these profiles, through how they vary over different local urban morphologies, and develop with respect to synoptic meteorological conditions, are important towards several aspects of UHI research; these include validating modelling urban canopy lapse rate profiles or estimating the growth of urban plumes. In this study, we utilised temperature sensors attached onto remote controlled aerial quadcopter platforms to measure urban temperature and humidity profiles in Singapore, which is a rapidly urbanizing major tropical metropolis. These profiles were measured from the surface to ~100 m above ground level, a height which includes all of the urban canopy and parts of the urban boundary layer. Initial results indicate significant variations in stability measured over different land uses (e.g. urban park, high-rise residential, commercial); these profiles are also temporally dynamic, depending on the time of day and larger-scale weather conditions.

Comparison of Measurements and FluorMOD Simulations for Solar Induced Chlorophyll Fluorescence and Reflectance of a Corn Crop under Nitrogen Treatments [SIF and Reflectance for Corn

NASA Technical Reports Server (NTRS)

Middleton, Elizabeth M.; Corp, Lawrence A.; Campbell, Petya K. E.

2007-01-01

The FLuorescence Explorer (FLEX) satellite concept is one of six semifinalist mission proposals selected in 2006 for pre-Phase studies by the European Space Agency (ESA). The FLEX concept proposes to measure passive solar induced chlorophyll fluorescence (SIF) of terrestrial ecosystems. A new spectral vegetation Fluorescence Model (FluorMOD) was developed to include the effects of steady state SIF on canopy reflectance. We used our laboratory and field measurements previously acquired from foliage and canopies of corn (Zea mays L.) under controlled nitrogen (N) fertilization to parameterize and evaluate FluorMOD. Our data included biophysical properties, fluorescence (F) and reflectance spectra for leaves; reflectance spectra of canopies and soil; solar irradiance; plot-level leaf area index; and canopy SIF emissions determined using the Fraunhofer Line Depth principal for the atmospheric telluric oxygen absorption features at 688 nm (O2-beta) and 760 nm (O2-alpha). FluorMOD simulations implemented in the default "look-up-table" mode did not reproduce the observed magnitudes of leaf F, canopy SIF, or canopy reflectance. However, simulations for all of these parameters agreed with observations when the default FluorMOD information was replaced with measurements, although N treatment responses were underestimated. Recommendations were provided to enhance FluorMOD's potential utility in support of SIF field experiments and studies of agriculture and ecosystems.

A new parameterization of the post-fire snow albedo effect

NASA Astrophysics Data System (ADS)

Gleason, K. E.; Nolin, A. W.

2013-12-01

Mountain snowpack serves as an important natural reservoir of water: recharging aquifers, sustaining streams, and providing important ecosystem services. Reduced snowpacks and earlier snowmelt have been shown to affect fire size, frequency, and severity in the western United States. In turn, wildfire disturbance affects patterns of snow accumulation and ablation by reducing canopy interception, increasing turbulent fluxes, and modifying the surface radiation balance. Recent work shows that after a high severity forest fire, approximately 60% more solar radiation reaches the snow surface due to the reduction in canopy density. Also, significant amounts of pyrogenic carbon particles and larger burned woody debris (BWD) are shed from standing charred trees, which concentrate on the snowpack, darken its surface, and reduce snow albedo by 50% during ablation. Although the post-fire forest environment drives a substantial increase in net shortwave radiation at the snowpack surface, driving earlier and more rapid melt, hydrologic models do not explicitly incorporate forest fire disturbance effects to snowpack dynamics. The objective of this study was to parameterize the post-fire snow albedo effect due to BWD deposition on snow to better represent forest fire disturbance in modeling of snow-dominated hydrologic regimes. Based on empirical results from winter experiments, in-situ snow monitoring, and remote sensing data from a recent forest fire in the Oregon High Cascades, we characterized the post-fire snow albedo effect, and developed a simple parameterization of snowpack albedo decay in the post-fire forest environment. We modified the recession coefficient in the algorithm: α = α0 + K exp (-nr) where α = snowpack albedo, α0 = minimum snowpack albedo (≈0.4), K = constant (≈ 0.44), -n = number of days since last major snowfall, r = recession coefficient [Rohrer and Braun, 1994]. Our parameterization quantified BWD deposition and snow albedo decay rates and related these forest disturbance effects to radiative heating and snow melt rates. We validated our parameterization of the post-fire snow albedo effect at the plot scale using a physically-based, spatially-distributed snow accumulation and melt model, and in-situ eddy covariance and snow monitoring data. This research quantified wildfire impacts to snow dynamics in the Oregon High Cascades, and provided a new parameterization of post-fire drivers to changes in high elevation winter water storage.

Assessing the effects of the Great Eastern China urbanization on the East Asian summer monsoon by coupling an urban canopy model with a Regional Climate Model

NASA Astrophysics Data System (ADS)

Liu, Z.; Xue, Y.; Liu, S.; Oleson, K. W.

2012-12-01

The urbanization causes one of the most significant land cover changes. Especially over the eastern China from Beijing to Shanghai, the great urbanization occurs during the past half century.It modifies the physical characteristics of land surface, including land surface albedo, surface roughness length and aerodynamicresistanceand thermodynamic conduction over land. All of these play very important role in regional climate change. Afteremploying several WRF/Urban models to tests land use and land cover change(LUCC) caused by urbanization in East Asia, we decided to introducea urban canopy submodule,the Community Land surface Model urban scheme(CLMU)to the WRF and coupled with the WRF-SSiB3 regional climate model. The CLMU and SSIB share the similar principal to treat the surface energy and water balances and aerodynamic resistance between land and atmosphere. In the urban module, the energy balances on the five surface conditions are considered separately: building roof, sun side building wall, shade side building wall, pervious land surface and impervious road. The surface turbulence calculation is based on Monin-Obukhov similarity theory. We have made further improvements for the urban module. Over each surface condition, a method to calculate sky view factor (SVF) is developed based on the physically process while most urban models simply provide an empirical value for SVF. Our approach along with other improvement in short and long wave radiation transfer improves the accuracy of long-wave and shortwave radiation processing over urban surface. The force-restore approximation is employed to calculate the temperature of each outer surfaces of building. The inner side temperature is used as the restore term and was assigned as a tuning constant. Based on the nature of the force-restore method and our tests, we decide to employ the air mean temperature of last 72 hours as a restore term, which substantially improve the surface energy balance. We evaluate the ability of the newly coupled model by two runs: one without and one with the urban canopy module. The coupled model is integrated from March through September, covering a summer monsoon season. The preliminary results show more significant urban heat island (UHI) effect over urban areas with the urban canopy model. The existence of the UHIs enhances the convection in lower atmosphere, affects the water vapor transportation and precipitation of the surrounding area, consistent with the phenomena that occur in urban areas. We further test the effect of urbanization on the monsoon by introducing two maps, one with and one without urbanization and the effect of the urbanization on the monsoon evolution and low level circulation will be discussed in the presentation.

Studying urban land-atmospheric interactions by coupling an urban canopy model with a single column atmospheric models

NASA Astrophysics Data System (ADS)

Song, J.; Wang, Z.

2013-12-01

Studying urban land-atmospheric interactions by coupling an urban canopy model with a single column atmospheric models Jiyun Song and Zhi-Hua Wang School of Sustainable Engineering and the Built Environment, Arizona State University, PO Box 875306, Tempe, AZ 85287-5306 Landuse landcover changes in urban area will modify surface energy budgets, turbulent fluxes as well as dynamic and thermodynamic structures of the overlying atmospheric boundary layer (ABL). In order to study urban land-atmospheric interactions, we coupled a single column atmospheric model (SCM) to a cutting-edge single layer urban canopy model (SLUCM). Modification of surface parameters such as the fraction of vegetation and engineered pavements, thermal properties of building and pavement materials, and geometrical features of street canyon, etc. in SLUCM dictates the evolution of surface balance of energy, water and momentum. The land surface states then provide lower boundary conditions to the overlying atmosphere, which in turn modulates the modification of ABL structure as well as vertical profiles of temperature, humidity, wind speed and tracer gases. The coupled SLUCM-SCM model is tested against field measurements of surface layer fluxes as well as profiles of temperature and humidity in the mixed layer under convective conditions. After model test, SLUCM-SCM is used to simulate the effect of changing urban land surface conditions on the evolution of ABL structure and dynamics. Simulation results show that despite the prescribed atmospheric forcing, land surface states impose significant impact on the physics of the overlying vertical atmospheric layer. Overall, this numerical framework provides a useful standalone modeling tool to assess the impacts of urban land surface conditions on the local hydrometeorology through land-atmospheric interactions. It also has potentially far-reaching implications to urban ecohydrological services for cities under future expansion and climate challenges.

Numerical Study of the Wintertime Planetary Boundary Layer Development in the Urban Area of Sao Paulo - Brazil

NASA Astrophysics Data System (ADS)

Ribeiro, F. N. D.; Soares, J.; Oliveira, A. P.; Miranda, R. M.; Chen, F.

2015-12-01

The gradual replacement of natural by built surfaces and the ongoing emission of particulate matter and other pollutants that happens in urban environments, besides degrading the environment, influence the local weather and climate patterns. Urban areas have different albedo, heat and hydraulic capacity and conductivity, roughness, emissivity, and transmissivity, when compared to naturally vegetated areas. This set of characteristics may change the surface energy budget, air temperature, humidity, atmospheric chemical composition, wind direction and velocity, and therefore the planetary boundary layer (PBL) development. The effects of urbanization on the PBL have been studied in many mid-latitude areas, however in the tropical or subtropical areas they are scarce. The MCITY Brazil project developed in 2 cities of Brazil, Sao Paulo (23°32' S) and Rio de Janeiro (latitude 22° 55' S), has provided the necessary data to properly investigate the effects of urbanization in these two cities. The project included a campaign of soundings launched every 3 hours for 10 consecutive days in August (Austral winter) from an airport at the north part of the city of Sao Paulo, that allowed the study of the PBL development, and also the measurements of the components of the energy budget equation by micrometeorological towers. Therefore, the goal of this work is to simulate the development of the PBL in the metropolitan area of Sao Paulo during winter, comparing its characteristics in urbanized and non urbanized sites, in order to assess the impact of urbanization on the development of the PBL in this area. The model used is the Weather Research and Forecast (WRF) with a single layer urban canopy parameterization (SLUCM) and realistic anthropogenic heat diurnal evolution. Preliminary results showed that the model is able to reproduce the PBL development during the campaign, including the passage of a cold-frontal system. The urban PBL reaches greater heights during the day than the PBL in non urban sites, suggesting that the urban sites generate more turbulence. Daytime urban PBL height reaches up to 2000 m and nighttime is usually less than 200 m. The surface turbulent fluxes and the energy budget near the surface will also be compared to observations and discussed.

Canopy volume removal from oil and gas development activity in the upper Susquehanna River basin in Pennsylvania and New York (USA): An assessment using lidar data

USGS Publications Warehouse

Young, John A.; Maloney, Kelly O.; Slonecker, Terry; Milheim, Lesley E.; Siripoonsup, David

2018-01-01

Oil and gas development is changing the landscape in many regions of the United States and globally. However, the nature, extent, and magnitude of landscape change and development, and precisely how this development compares to other ongoing land conversion (e.g. urban/sub-urban development, timber harvest) is not well understood. In this study, we examine land conversion from oil and gas infrastructure development in the upper Susquehanna River basin in Pennsylvania and New York, an area that has experienced much oil and gas development over the past 10 years. We quantified land conversion in terms of forest canopy geometric volume loss in contrast to previous studies that considered only areal impacts. For the first time in a study of this type, we use fine-scale lidar forest canopy geometric models to assess the volumetric change due to forest clearing from oil and gas development and contrast this land change to clear cut forest harvesting, and urban and suburban development. Results show that oil and gas infrastructure development removed a large volume of forest canopy from 2006 to 2013, and this removal spread over a large portion of the study area. Timber operations (clear cutting) on Pennsylvania State Forest lands removed a larger total volume of forest canopy during the same time period, but this canopy removal was concentrated in a smaller area. Results of our study point to the need to consider volumetric impacts of oil and gas development on ecosystems, and to place potential impacts in context with other ongoing land conversions.

A framework for adapting urban forests to climate change

Treesearch

Leslie Brandt; Abigail Derby Lewis; Robert Fahey; Lydia Scott; Lindsay Darling; Chris Swanston

2016-01-01

Planting urban trees and expanding urban forest canopy cover are often considered key strategies for reducing climate change impacts in urban areas. However, urban trees and forests can also be vulnerable to climate change through shifts in tree habitat suitability, changes in pests and diseases, and changes in extreme weather events. We developed a three-step...

Exploring the spatial distribution of light interception and photosynthesis of canopies by means of a functional-structural plant model.

PubMed

Sarlikioti, V; de Visser, P H B; Marcelis, L F M

2011-04-01

At present most process-based models and the majority of three-dimensional models include simplifications of plant architecture that can compromise the accuracy of light interception simulations and, accordingly, canopy photosynthesis. The aim of this paper is to analyse canopy heterogeneity of an explicitly described tomato canopy in relation to temporal dynamics of horizontal and vertical light distribution and photosynthesis under direct- and diffuse-light conditions. Detailed measurements of canopy architecture, light interception and leaf photosynthesis were carried out on a tomato crop. These data were used for the development and calibration of a functional-structural tomato model. The model consisted of an architectural static virtual plant coupled with a nested radiosity model for light calculations and a leaf photosynthesis module. Different scenarios of horizontal and vertical distribution of light interception, incident light and photosynthesis were investigated under diffuse and direct light conditions. Simulated light interception showed a good correspondence to the measured values. Explicitly described leaf angles resulted in higher light interception in the middle of the plant canopy compared with fixed and ellipsoidal leaf-angle distribution models, although the total light interception remained the same. The fraction of light intercepted at a north-south orientation of rows differed from east-west orientation by 10 % on winter and 23 % on summer days. The horizontal distribution of photosynthesis differed significantly between the top, middle and lower canopy layer. Taking into account the vertical variation of leaf photosynthetic parameters in the canopy, led to approx. 8 % increase on simulated canopy photosynthesis. Leaf angles of heterogeneous canopies should be explicitly described as they have a big impact both on light distribution and photosynthesis. Especially, the vertical variation of photosynthesis in canopy is such that the experimental approach of photosynthesis measurements for model parameterization should be revised.

Exploring the spatial distribution of light interception and photosynthesis of canopies by means of a functional–structural plant model

PubMed Central

Sarlikioti, V.; de Visser, P. H. B.; Marcelis, L. F. M.

2011-01-01

Background and Aims At present most process-based models and the majority of three-dimensional models include simplifications of plant architecture that can compromise the accuracy of light interception simulations and, accordingly, canopy photosynthesis. The aim of this paper is to analyse canopy heterogeneity of an explicitly described tomato canopy in relation to temporal dynamics of horizontal and vertical light distribution and photosynthesis under direct- and diffuse-light conditions. Methods Detailed measurements of canopy architecture, light interception and leaf photosynthesis were carried out on a tomato crop. These data were used for the development and calibration of a functional–structural tomato model. The model consisted of an architectural static virtual plant coupled with a nested radiosity model for light calculations and a leaf photosynthesis module. Different scenarios of horizontal and vertical distribution of light interception, incident light and photosynthesis were investigated under diffuse and direct light conditions. Key Results Simulated light interception showed a good correspondence to the measured values. Explicitly described leaf angles resulted in higher light interception in the middle of the plant canopy compared with fixed and ellipsoidal leaf-angle distribution models, although the total light interception remained the same. The fraction of light intercepted at a north–south orientation of rows differed from east–west orientation by 10 % on winter and 23 % on summer days. The horizontal distribution of photosynthesis differed significantly between the top, middle and lower canopy layer. Taking into account the vertical variation of leaf photosynthetic parameters in the canopy, led to approx. 8 % increase on simulated canopy photosynthesis. Conclusions Leaf angles of heterogeneous canopies should be explicitly described as they have a big impact both on light distribution and photosynthesis. Especially, the vertical variation of photosynthesis in canopy is such that the experimental approach of photosynthesis measurements for model parameterization should be revised. PMID:21355008

Spatial patterns of ecohydrologic properties on a hillslope-alluvial fan transect, central New Mexico

USGS Publications Warehouse

Bedford, D.R.; Small, E.E.

2008-01-01

Spatial patterns of soil properties are linked to patchy vegetation in arid and semi-arid landscapes. The patterns of soil properties are generally assumed to be linked to the ecohydrological functioning of patchy dryland vegetation ecosystems. We studied the effects of vegetation canopy, its spatial pattern, and landforms on soil properties affecting overland flow and infiltration in shrublands at the Sevilleta National Wildlife Refuge/LTER in central New Mexico, USA. We studied the patterns of microtopography and saturated conductivity (Ksat), and generally found it to be affected by vegetation canopy and pattern, as well as landform type. On gently sloping alluvial fans, both microtopography and Ksat are high under vegetation canopy and decay with distance from plant center. On steeper hillslope landforms, only microtopography was significantly higher under vegetation canopy, while there was no significant difference in Ksat between vegetation and interspaces. Using geostatistics, we found that the spatial pattern of soil properties was determined by the spatial pattern of vegetation. Most importantly, the effects of vegetation were present in the unvegetated interspaces 2-4 times the extent of vegetation canopy, on the order of 2-3??m. Our results have implications for the understanding the ecohydrologic function of semi-arid ecosystems as well as the parameterization of hydrologic models. ?? 2007 Elsevier B.V. All rights reserved.

Measurements and Computations of Flow in an Urban Street System

NASA Astrophysics Data System (ADS)

Castro, Ian P.; Xie, Zheng-Tong; Fuka, V.; Robins, Alan G.; Carpentieri, M.; Hayden, P.; Hertwig, D.; Coceal, O.

2017-02-01

We present results from laboratory and computational experiments on the turbulent flow over an array of rectangular blocks modelling a typical, asymmetric urban canopy at various orientations to the approach flow. The work forms part of a larger study on dispersion within such arrays (project DIPLOS) and concentrates on the nature of the mean flow and turbulence fields within the canopy region, recognising that unless the flow field is adequately represented in computational models there is no reason to expect realistic simulations of the nature of the dispersion of pollutants emitted within the canopy. Comparisons between the experimental data and those obtained from both large-eddy simulation (LES) and direct numerical simulation (DNS) are shown and it is concluded that careful use of LES can produce generally excellent agreement with laboratory and DNS results, lending further confidence in the use of LES for such situations. Various crucial issues are discussed and advice offered to both experimentalists and those seeking to compute canopy flows with turbulence resolving models.

The Influence of a Sandy Substrate, Seagrass, or Highly Turbid Water on Albedo and Surface Heat Flux

NASA Astrophysics Data System (ADS)

Fogarty, M. C.; Fewings, M. R.; Paget, A. C.; Dierssen, H. M.

2018-01-01

Sea-surface albedo is a combination of surface-reflected and water-leaving irradiance, but water-leaving irradiance typically contributes less than 15% of the total albedo in open-ocean conditions. In coastal systems, however, the bottom substrate or suspended particulate matter can increase the amount of backscattered light, thereby increasing albedo and decreasing net shortwave surface heat flux. Here a sensitivity analysis using observations and models predicts the effect of light scattering on albedo and the net shortwave heat flux for three test cases: a bright sand bottom, a seagrass canopy, and turbid water. After scaling to the full solar shortwave spectrum, daytime average albedo for the test cases is up to 0.20 and exceeds the value of 0.05 predicted using a commonly applied parameterization. Daytime net shortwave heat flux into the water is significantly reduced, particularly for waters with bright sediments, dense horizontal seagrass canopies < 0.25 m from the sea surface, or highly turbid waters with suspended particulate matter concentration ≥ 50 g m-3. Observations of a more vertical seagrass canopy within 0.2 and 1 m of the surface indicate the increase in albedo compared to the common parameterization is negligible. Therefore, we suggest that the commonly applied albedo lookup table can be used in coastal heat flux estimates in water as shallow as 1 m unless the bottom substrate is highly reflective or the water is highly turbid. Our model results provide guidance to researchers who need to determine albedo in highly reflective or highly turbid conditions but have no direct observations.

Differential Impact of Passive versus Active Irrigation on Urban Forests in Semiarid Regions

NASA Astrophysics Data System (ADS)

Luketich, A. M.; Papuga, S. A.; Crimmins, M.

2017-12-01

The network of trees within a city provides a variety of ecosystem services such as flood mitigation and reduced heat island effects. To maintain these `urban forests' in semiarid cities, the use of scarce water resources for irrigation is often necessary. Rainwater harvesting has been widely adopted in Tucson, AZ as a sustainable water source for trees, but the effects of passive water harvesting versus active irrigation on tree canopy productivity and microclimate is largely unquantified. We hypothesize that regardless of whether trees are passively or actively irrigated, deep soil moisture will be elevated compared to natural conditions; however, we expect that increased deep soil moisture conditions will be more frequent using active irrigation. Additionally, we hypothesize that similar to natural settings, urban trees will need access deep soil moisture for transpiration. Therefore, we expect that actively irrigated trees will have more periods of transpiration than passively irrigated trees and that this will result in elevated and sustained phenological activity. We also expect that this difference will translate to more ecosystem services for a longer portion of the year in actively irrigated urban forests. Here, we compare key ecohydrological indicators of passive and active irrigation systems at two sites in Tucson, AZ. Our measurements include soil moisture, transpiration, air temperature, soil temperature, below- and within- canopy temperatures, and canopy phenology. Our first year of results suggest there are differences in transpiration, canopy greening and microclimate between the two irrigation techniques and that the magnitude of these differences are highly seasonal. This research can help to improve understanding of the practices and function of green infrastructure in semiarid cities and inform models that attempt to aggregate the influence of these urban forests for understanding watershed management strategies.

Land-Atmosphere Coupling in the Multi-Scale Modelling Framework

NASA Astrophysics Data System (ADS)

Kraus, P. M.; Denning, S.

2015-12-01

The Multi-Scale Modeling Framework (MMF), in which cloud-resolving models (CRMs) are embedded within general circulation model (GCM) gridcells to serve as the model's cloud parameterization, has offered a number of benefits to GCM simulations. The coupling of these cloud-resolving models directly to land surface model instances, rather than passing averaged atmospheric variables to a single instance of a land surface model, the logical next step in model development, has recently been accomplished. This new configuration offers conspicuous improvements to estimates of precipitation and canopy through-fall, but overall the model exhibits warm surface temperature biases and low productivity.This work presents modifications to a land-surface model that take advantage of the new multi-scale modeling framework, and accommodate the change in spatial scale from a typical GCM range of ~200 km to the CRM grid-scale of 4 km.A parameterization is introduced to apportion modeled surface radiation into direct-beam and diffuse components. The diffuse component is then distributed among the land-surface model instances within each GCM cell domain. This substantially reduces the number excessively low light values provided to the land-surface model when cloudy conditions are modeled in the CRM, associated with its 1-D radiation scheme. The small spatial scale of the CRM, ~4 km, as compared with the typical ~200 km GCM scale, provides much more realistic estimates of precipitation intensity, this permits the elimination of a model parameterization of canopy through-fall. However, runoff at such scales can no longer be considered as an immediate flow to the ocean. Allowing sub-surface water flow between land-surface instances within the GCM domain affords better realism and also reduces temperature and productivity biases.The MMF affords a number of opportunities to land-surface modelers, providing both the advantages of direct simulation at the 4 km scale and a much reduced conceptual gap between model resolution and parameterized processes.

Forest Canopy Heights in Amazon River Basin Forests as Estimated with the Geoscience Laser Altimeter System (GLAS)

Treesearch

E. H. Helmer; M. A. Lefsky

2006-01-01

Land-use change, mainly forest burning, harvest, or clearing for agriculture, may compose 15 to 40 percent of annual human-caused emissions of carbon (C) to the atmosphere. Spatially extensive data on forest C pools can validate and parameterize atmospheric and ecosystem models of those fluxes and quantify fluxes from forest change. Excellent evidence exists that light...

i-Tree: Tools to assess and manage structure, function, and value of community forests

NASA Astrophysics Data System (ADS)

Hirabayashi, S.; Nowak, D.; Endreny, T. A.; Kroll, C.; Maco, S.

2011-12-01

Trees in urban communities can mitigate many adverse effects associated with anthropogenic activities and climate change (e.g. urban heat island, greenhouse gas, air pollution, and floods). To protect environmental and human health, managers need to make informed decisions regarding urban forest management practices. Here we present the i-Tree suite of software tools (www.itreetools.org) developed by the USDA Forest Service and their cooperators. This software suite can help urban forest managers assess and manage the structure, function, and value of urban tree populations regardless of community size or technical capacity. i-Tree is a state-of-the-art, peer-reviewed Windows GUI- or Web-based software that is freely available, supported, and continuously refined by the USDA Forest Service and their cooperators. Two major features of i-Tree are 1) to analyze current canopy structures and identify potential planting spots, and 2) to estimate the environmental benefits provided by the trees, such as carbon storage and sequestration, energy conservation, air pollution removal, and storm water reduction. To cover diverse forest topologies, various tools were developed within the i-Tree suite: i-Tree Design for points (individual trees), i-Tree Streets for lines (street trees), and i-Tree Eco, Vue, and Canopy (in the order of complexity) for areas (community trees). Once the forest structure is identified with these tools, ecosystem services provided by trees can be estimated with common models and protocols, and reports in the form of texts, charts, and figures are then created for users. Since i-Tree was developed with a client/server architecture, nationwide data in the US such as location-related parameters, weather, streamflow, and air pollution data are stored in the server and retrieved to a user's computer at run-time. Freely available remote-sensed images (e.g. NLCD and Google maps) are also employed to estimate tree canopy characteristics. As the demand for i-Tree grows internationally, environmental databases from more countries will be coupled with the software suite. Two more i-Tree applications, i-Tree Forecast and i-Tree Landscape are now under development. i-Tree Forecast simulates canopy structures for up to 100 years based on planting and mortality rates and adds capabilities for other i-Tree applications to estimate the benefits of future canopy scenarios. While most i-Tree applications employ a spatially lumped approach, i-Tree landscape employs a spatially distributed approach that allows users to map changes in canopy cover and ecosystem services through time and space. These new i-Tree tools provide an advanced platform for urban managers to assess the impact of current and future urban forests. i-Tree allows managers to promote effective urban forest management and sound arboricultural practices by providing information for advocacy and planning, baseline data for making informed decisions, and standardization for comparisons with other communities.

Building-Resolved CFD Simulations for Greenhouse Gas Transport and Dispersion over Washington DC / Baltimore

NASA Astrophysics Data System (ADS)

Prasad, K.; Lopez-Coto, I.; Ghosh, S.; Mueller, K.; Whetstone, J. R.

2015-12-01

The North-East Corridor project aims to use a top-down inversion methodology to quantify sources of Greenhouse Gas (GHG) emissions over urban domains such as Washington DC / Baltimore with high spatial and temporal resolution. Atmospheric transport of tracer gases from an emission source to a tower mounted receptor are usually conducted using the Weather Research and Forecasting (WRF) model. For such simulations, WRF employs a parameterized turbulence model and does not resolve the fine scale dynamics generated by the flow around buildings and communities comprising a large city. The NIST Fire Dynamics Simulator (FDS) is a computational fluid dynamics model that utilizes large eddy simulation methods to model flow around buildings at length scales much smaller than is practical with WRF. FDS has the potential to evaluate the impact of complex urban topography on near-field dispersion and mixing difficult to simulate with a mesoscale atmospheric model. Such capabilities may be important in determining urban GHG emissions using atmospheric measurements. A methodology has been developed to run FDS as a sub-grid scale model within a WRF simulation. The coupling is based on nudging the FDS flow field towards that computed by WRF, and is currently limited to one way coupling performed in an off-line mode. Using the coupled WRF / FDS model, NIST will investigate the effects of the urban canopy at horizontal resolutions of 10-20 m in a domain of 12 x 12 km. The coupled WRF-FDS simulations will be used to calculate the dispersion of tracer gases in the North-East Corridor and to evaluate the upwind areas that contribute to tower observations, referred to in the inversion community as influence functions. Results of this study will provide guidance regarding the importance of explicit simulations of urban atmospheric turbulence in obtaining accurate estimates of greenhouse gas emissions and transport.

Effects of Explicit Urban-Canopy Representation on Local Circulations Above a Tropical Mega-City

NASA Astrophysics Data System (ADS)

Flores Rojas, José L.; Pereira Filho, Augusto J.; Karam, Hugo A.; Vemado, Felipe; Masson, Valéry

2018-01-01

The Advanced Regional Prediction System (ARPS) is coupled with the tropical town energy budget (tTEB) scheme to analyze the effects of the urban canopy circulation over the metropolitan area of São Paulo and its interactions with the sea breeze and mountain-valley circulation in the eastern state of São Paulo, Brazil. Two experiments are carried out for the typical sea-breeze event occurring on 22 August 2014 under weak synoptic forcing and clear-sky conditions: (a) a control run with the default semi-desert surface parametrization and; (b) a tTEB run for the urban canopy of São Paulo. A realistic land-use database over the south-eastern domain of Brazil is used in the downscaling simulation to a horizontal grid resolution of 3 km. Our results indicate that ARPS effectively simulates features of the nighttime and early morning land-breeze circulation, which is affected by the surrounding hills and the nocturnal heat island of São Paulo. By early afternoon, the south-eastern sea-breeze circulation moves inland perpendicular to the upslope of the Serra do Mar scarp, which generates a line of moisture convergence and updrafts further inland. Later, the convergence line reaches São Paulo and interacts with the circulation arising from the urban heat island (UHI), which increases the moisture convergence and strength of updrafts. The surface energy balance indicates that the UHI is caused by large sensible heat storage within the urban canopy during the day, which is later released in the afternoon and at night. The simulations are verified with available radiosonde and surface weather station data, land-surface-temperature estimates from the moderate resolution imaging spectroradiometer, as well as the National Center for Atmospheric Research reanalysis databases. The three-dimensional geometry of the urban canyons within the tTEB scheme consistently improves the thermodynamically-induced circulation over São Paulo.

Competition for light between individual trees lowers reference canopy stomatal conductance: Results from a model

NASA Astrophysics Data System (ADS)

Loranty, Michael M.; Mackay, D. Scott; Ewers, Brent E.; Traver, Elizabeth; Kruger, Eric L.

2010-12-01

We have used an ecosystem model, TREES (Terrestrial Regional Ecosystem Exchange Simulator), to test the hypothesis that competition for light limits reference canopy stomatal conductance (GSref; conductance at 1 kPa vapor pressure deficit) for individual tree crowns. Sap flux (JS) data was collected at an aspen-dominated unmanaged early successional site, and at a sugar maple dominated midsuccessional site managed for timber production. Using a Monte Carlo approach, JS scaled canopy transpiration (EC) estimates were used to parameterize two versions of the model for each tree individually; a control model treated trees as isolated individuals, and a modified version incorporated the shading effects of neighboring individuals on incident radiation. Agreement between simulated and observed EC was better for maple than for aspen using the control model. Accounting for canopy heterogeneity using a three-dimensional canopy representation had minimal effects on estimates of GSref or model performance for individual maples. At the Aspen site the modified model resulted in improved EC estimates, particularly for trees with lower GSref and more shading by neighboring individuals. Our results imply a link between photosynthetic capacity, as mediated by competitive light environment, and GSref. We conclude that accounting for the effects of canopy heterogeneity on incident radiation improves modeled estimates of canopy carbon and water fluxes, especially for shade intolerant species. Furthermore our results imply a link between ecosystem structure and function that may be exploited to elucidate the impacts of forest structural heterogeneity on ecosystem fluxes of carbon and water via LiDAR remote sensing.

Development of Gridded Fields of Urban Canopy Parameters for Advanced Urban Meteorological and Air Quality Models

EPA Science Inventory

Urban dispersion and air quality simulation models applied at various horizontal scales require different levels of fidelity for specifying the characteristics of the underlying surfaces. As the modeling scales approach the neighborhood level (~1 km horizontal grid spacing), the...

Homeowner interactions with residential trees in urban areas

Treesearch

Jana Dilley; Kathleen L. Wolf

2013-01-01

Urban forests are a critical element in sustainable urban areas because of the many environmental, economic, and social benefits that city trees provide. In order to increase canopy cover in urban areas, residential homeowners, who collectively own the majority of the land in most cities, need to engage in planting and retaining trees on their properties. This...

Long-term and direct measurements of CO[sub 2] and water vapor exchange over a deciduous forest canopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greco, S.; Baldocchi, D.D.

1994-06-01

Long-term monitoring of CO[sub 2] and water vapor exchange is needed to determine components of the carbon and hydrologic cycles and to provide data for parameterizing and testing assessment models. Responding to this need we initiated a continous field measurement campaign in April 1993 in a deciduous forest growing near Oak Ridge, TN. The micrometerological eddy correlation method was used to measure flux densities of CO[sub 2] and water vapor over the canopy. Periodic measurements were made of stomatal resistence and pre-dawn water potential to characterize the photosynthetic capacity of the canopy. Three factors accounted for a disproportionate amount ofmore » seasonal variance in CO[sub 2] flux densities: photon flux densities, leaf area and the occurrence of drought. Positive and increasing magnitudes of carbon gain were observed between April and June as leaves expanded, the canopy closed and daily insolation increased. At midsummer a drought and heat spell were experienced. This period caused CO[sub 2] flux densities to decline. By late summer adequate precipitation and replenishment of soil water resurrected carbon uptake rates until autumnal leaf senescence and leaf fall.« less

Measuring and modeling changes in land-atmosphere exchanges and hydrologic response in forests undergoing insect-driven mortality

NASA Astrophysics Data System (ADS)

Gochis, D. J.; Brooks, P. D.; Harpold, A. A.; Ewers, B. E.; Pendall, E.; Barnard, H. R.; Reed, D.; Harley, P. C.; Hu, J.; Biederman, J.

2010-12-01

Given the magnitude and spatial extent of recent forest mortality in the western U.S. there is a pressing need to improve representation of such influences on the exchange of energy, water, biogeochemical and momentum fluxes in land-atmosphere parameterizations coupled to weather and climate models. In this talk we present observational data and model results from a new study aimed at improving understanding the impacts of mountain pine beetle-induced forest mortality in the central Rocky Mountains. Baseline observations and model runs from undisturbed lodgepole pine forest conditions are developed as references against which new observations and model runs from infested stands are compared. We will specifically look at the structure and evolution of sub-canopy energy exchange variables such as shortwave and longwave radiation and sub-canopy turbulence as well as sub-canopy precipitation, sapflow fluxes, canopy-scale fluxes and soil moisture and temperature. In this manner we seek to lay the ground work for evaluating the recent generation of land surface model changes aimed at representing insect-related forest dynamics in the CLM-C/N and Noah land surface models.

Human and biophysical legacies shape contemporary urban forests: A literature synthesis

Treesearch

Lara A. Roman; Hamil Pearsall; Theodore S. Eisenman; Tenley M. Conway; Robert T. Fahey; Shawn Landry; Jess Vogt; Natalie S. van Doorn; J. Morgan Grove; Dexter H. Locke; Adrina C. Bardekjian; John J. Battles; Mary L. Cadenasso; Cecil C. Konijnendijk van den Bosch; Meghan Avolio; Adam Berland; G. Darrel Jenerette; Sarah K. Mincey; Diane E. Pataki; Christina Staudhammer

2018-01-01

Understanding how urban forests developed their current patterns of tree canopy cover, species composition, and diversity requires an appreciation of historical legacy effects. However, analyses of current urban forest characteristics are often limited to contemporary socioeconomic factors, overlooking the role of history. The institutions, human communities, and...

Parameterization of the 3-PG model for Pinus elliottii stands using alternative methods to estimate fertility rating, biomass partitioning and canopy closure

Treesearch

Carlos A. Gonzalez-Benecke; Eric J. Jokela; Wendell P. Cropper; Rosvel Bracho; Daniel J. Leduc

2014-01-01

The forest simulation model, 3-PG, has been widely applied as a useful tool for predicting growth of forest species in many countries. The model has the capability to estimate the effects of management, climate and site characteristics on many stand attributes using easily available data. Currently, there is an increasing interest in estimating biomass and assessing...

Constraining 3-PG with a new δ13C submodel: a test using the δ13C of tree rings.

PubMed

Wei, Liang; Marshall, John D; Link, Timothy E; Kavanagh, Kathleen L; DU, Enhao; Pangle, Robert E; Gag, Peter J; Ubierna, Nerea

2014-01-01

A semi-mechanistic forest growth model, 3-PG (Physiological Principles Predicting Growth), was extended to calculate δ(13)C in tree rings. The δ(13)C estimates were based on the model's existing description of carbon assimilation and canopy conductance. The model was tested in two ~80-year-old natural stands of Abies grandis (grand fir) in northern Idaho. We used as many independent measurements as possible to parameterize the model. Measured parameters included quantum yield, specific leaf area, soil water content and litterfall rate. Predictions were compared with measurements of transpiration by sap flux, stem biomass, tree diameter growth, leaf area index and δ(13)C. Sensitivity analysis showed that the model's predictions of δ(13)C were sensitive to key parameters controlling carbon assimilation and canopy conductance, which would have allowed it to fail had the model been parameterized or programmed incorrectly. Instead, the simulated δ(13)C of tree rings was no different from measurements (P > 0.05). The δ(13)C submodel provides a convenient means of constraining parameter space and avoiding model artefacts. This δ(13)C test may be applied to any forest growth model that includes realistic simulations of carbon assimilation and transpiration. © 2013 John Wiley & Sons Ltd.

Estimation of Vegetation Aerodynamic Roughness of Natural Regions Using Frontal Area Density Determined from Satellite Imagery

NASA Technical Reports Server (NTRS)

Jasinski, Michael F.; Crago, Richard

1994-01-01

Parameterizations of the frontal area index and canopy area index of natural or randomly distributed plants are developed, and applied to the estimation of local aerodynamic roughness using satellite imagery. The formulas are expressed in terms of the subpixel fractional vegetation cover and one non-dimensional geometric parameter that characterizes the plant's shape. Geometrically similar plants and Poisson distributed plant centers are assumed. An appropriate averaging technique to extend satellite pixel-scale estimates to larger scales is provided. ne parameterization is applied to the estimation of aerodynamic roughness using satellite imagery for a 2.3 sq km coniferous portion of the Landes Forest near Lubbon, France, during the 1986 HAPEX-Mobilhy Experiment. The canopy area index is estimated first for each pixel in the scene based on previous estimates of fractional cover obtained using Landsat Thematic Mapper imagery. Next, the results are incorporated into Raupach's (1992, 1994) analytical formulas for momentum roughness and zero-plane displacement height. The estimates compare reasonably well to reference values determined from measurements taken during the experiment and to published literature values. The approach offers the potential for estimating regionally variable, vegetation aerodynamic roughness lengths over natural regions using satellite imagery when there exists only limited knowledge of the vegetated surface.

Automatic extraction of tree crowns from aerial imagery in urban environment

NASA Astrophysics Data System (ADS)

Liu, Jiahang; Li, Deren; Qin, Xunwen; Yang, Jianfeng

2006-10-01

Traditionally, field-based investigation is the main method to investigate greenbelt in urban environment, which is costly and low updating frequency. In higher resolution image, the imagery structure and texture of tree canopy has great similarity in statistics despite the great difference in configurations of tree canopy, and their surface structures and textures of tree crown are very different from the other types. In this paper, we present an automatic method to detect tree crowns using high resolution image in urban environment without any apriori knowledge. Our method catches unique structure and texture of tree crown surface, use variance and mathematical expectation of defined image window to position the candidate canopy blocks coarsely, then analysis their inner structure and texture to refine these candidate blocks. The possible spans of all the feature parameters used in our method automatically generate from the small number of samples, and HOLE and its distribution as an important characteristics are introduced into refining processing. Also the isotropy of candidate image block and holes' distribution is integrated in our method. After introduction the theory of our method, aerial imageries were used ( with a resolution about 0.3m ) to test our method, and the results indicate that our method is an effective approach to automatically detect tree crown in urban environment.

Modeling the formation and aging of secondary organic aerosols in the Los Angeles metropolitan region during the CalNex 2010 field campaign

NASA Astrophysics Data System (ADS)

Hayes, P. L.; Ma, P. K.; Jimenez, J. L.; Zhao, Y.; Robinson, A. L.; Carlton, A. M. G.; Baker, K. R.; Ahmadov, R.; Washenfelder, R. A.; Alvarez, S. L.; Rappenglück, B.; Gilman, J.; Kuster, W.; De Gouw, J. A.; Prevot, A. S.; Zotter, P.; Szidat, S.; Kleindienst, T. E.; Offenberg, J. H.

2015-12-01

Several different literature parameterizations for the formation and evolution of urban secondary organic aerosol (SOA) are evaluated using a box model representing the Los Angeles Region during CalNex. The model SOA formed only from the oxidation of VOCs (V-SOA) is insufficient to explain the observed SOA concentrations, even when using SOA parameterizations with multi-generation oxidation that produce much higher yields than have been observed in chamber experiments, or when increasing yields to their upper limit estimates accounting for recently reported losses of vapors to chamber walls. Including SOA from primary semi-volatile and intermediate volatility organic compounds (P-S/IVOCs) following the parameterizations of Robinson et al. (2007), Grieshop et al. (2009), or Pye and Seinfeld (2010) improves model/measurement agreement for mass concentration at shorter photochemical ages (0.5 days). Our results strongly suggest that other precursors besides VOCs are needed to explain the observed SOA concentrations. In contrast, all of the literature P-S/IVOC parameterizations over-predict urban SOA formation at long photochemical ages (3 days) compared to observations from multiple sites, which can lead to problems in regional and global modeling. Sensitivity studies that reduce the IVOC emissions by one-half in the model improve SOA predictions at these long ages. In addition, when IVOC emissions in the Robinson et al. parameterization are constrained using recently reported measurements of these species model/measurement agreement is achieved. The amounts of SOA mass from diesel vehicles, gasoline vehicles, and cooking emissions are estimated to be 16 - 27%, 35 - 61%, and 19 - 35%, respectively, depending on the parameterization used, which is consistent with the observed fossil fraction of urban SOA, 71(±3)%. The percentage of SOA from diesel vehicle emissions is the same, within the estimated uncertainty, as reported in previous work that analyzed the weekly cycles in SOA concentrations (Bahreini et al., 2012; Hayes et al., 2013). However, the modeling work presented here suggests a strong anthropogenic source of modern carbon in urban SOA, possibly cooking emissions, that was not accounted for in those previous studies, and which is higher on weekends.

Modeling the Urban Boundary and Canopy Layers

EPA Science Inventory

Today, we are confronted with increasingly more sophisticated application requirements for urban modeling. These include those that address emergency response to acute exposures from toxic releases, health exposure assessments from adverse air quality, energy usage, and character...

Gas-particle interactions above a Dutch heathland: I. Surface exchange fluxes of NH3, SO2, HNO3 and HCl

NASA Astrophysics Data System (ADS)

Nemitz, E.; Sutton, M. A.; Wyers, G. P.; Jongejan, P. A. C.

2004-07-01

A field measurement campaign was carried out over a Dutch heathland to investigate the effect of gas-to-particle conversion and ammonium aerosol evaporation on surface/atmosphere fluxes of ammonia and related species. Continuous micrometeorological measurements of the surface exchange of NH3, SO2, HNO3 and HCl were made and are analyzed here with regard to average fluxes, deposition velocities (Vd), canopy resistances (Rc) and canopy compensation point for NH3. Gradients of SO2, HNO3 and HCl were measured with a novel wet-denuder system with online anion chromatography. Measurements of HNO3 and HCl indicate an Rc of 100 to 200 s m-1 during warm daytime periods, probably at least partly due to non-zero acid partial pressures above NH4NO3 and NH4Cl on the leaf surfaces. Although it is likely that this observation is exacerbated by the effect of the evaporation of airborne NH4+ on the gradient measurements, the findings nevertheless add to the growing evidence that HNO3 and HCl are not always deposited at the maximum rate. Ammonia (NH3) fluxes show mainly deposition, with some periods of significant daytime emission. The net exchange could be reproduced both with an Rc model (deposition fluxes only) using resistance parameterizations from former measurements, as well as with the canopy compensation point model, using parameterizations derived from the measurements. The apoplastic ratio of ammonium and hydrogen concentration (Γs=[NH4+]/[H+]) of 1200 estimated from the measurements is large for semi-natural vegetation, but smaller than indicated by previous measurements at this site.

Gas-particle interactions above a Dutch heathland: I. Surface exchange fluxes of NH3, SO2, HNO3 and HCl

NASA Astrophysics Data System (ADS)

Nemitz, E.; Sutton, M. A.; Wyers, G. P.; Jongejan, P. A. C.

2004-03-01

A field measurement campaign was carried out over a Dutch heathland to investigate the effect of gas-to-particle conversion and ammonium aerosol evaporation on surface/atmosphere fluxes of ammonia and related species. Continuous micrometeorological measurements of the surface exchange of NH3, SO2, HNO3 and HCl were made and are analyzed here with regard to average fluxes, deposition velocities (Vd), canopy resistances (Rc) and canopy compensation point for NH3. Gradients of SO2, HNO3 and HCl were measured with a novel wet-denuder system with online anion chromatography. Measurements of HNO3 and HCl indicate an Rc of 100 to 200 s m-1 during warm daytime periods, probably at least partly due to non-zero acid partial pressures above NH4NO3 and NH4Cl on the leaf surfaces. Although it is likely that this observation is exacerbated by the effect of the evaporation of airborne NH4+ on the gradient measurements, the findings nevertheless add to the growing evidence that HNO3 and HCl are not always deposited at the maximum rate. Ammonia (NH3) fluxes show mainly deposition, with some periods of significant daytime emission. The net exchange could be reproduced both with an Rc model (deposition fluxes only) using resistance parameterizations from former measurements, as well as with the canopy compensation point model, using parameterizations derived from the measurements. The apoplastic ratio of ammonium and hydrogen concentration (Γs=[NH4+]/[H+]) of 1200 estimated from the measurements is large for semi- natural vegetation, but smaller than indicated by previous measurements at this site.

SIRANERISK: Modelling dispersion of steady and unsteady pollutant releases in the urban canopy

NASA Astrophysics Data System (ADS)

Soulhac, L.; Lamaison, G.; Cierco, F.-X.; Ben Salem, N.; Salizzoni, P.; Mejean, P.; Armand, P.; Patryl, L.

2016-09-01

SIRANERISK is an operational model for the simulation of the dispersion of unsteady atmospheric releases of pollutant within and above an urban area. SIRANERISK is built on the same principles as the SIRANE model, and couples a street network model for the pollutant transfers within the urban canopy with a Gaussian puff model for the transfers above it. The performance of the model are here analysed by a detailed comparisons with wind-tunnel experiments. These experiments concern the dispersion of steady and unsteady pollutant releases within and above obstacle arrays with varying geometrical configurations, representing different topologies of idealised urban districts. The overall good agreement between numerical and experimental data demonstrates the reliability of SIRANERISK as an operational tool for the assessment of risk analysis and for the management of crises due to the accidental release of harmful airborne pollutants within a built environment.

Assessing the US Urban Forest Resources

Treesearch

David J. Nowak; Mary H. Noble; Susan M. Sisinni; John F. Dwyer

2001-01-01

Urban areas in the conterminous United States doubled in size between 1969 and 1994, and currently cover 3.5 percent of the total land area and contain more than 75 percent of the US population. Urban areas contain approximately 3.8 billion trees with an average tree canopy cover of 27 percent. The extent and variation of urban forests across the 48 states are explored...

Projecting land-use and land cover change in a subtropical urban watershed

Treesearch

John J. Lagrosa IV; Wayne C. Zipperer; Michael G. Andreu

2018-01-01

Urban landscapes are heterogeneous mosaics that develop via significant land-use and land cover (LULC) change. Current LULC models project future landscape patterns, but generally avoid urban landscapes due to heterogeneity. To project LULC change for an urban landscape, we parameterize an established LULC model (Dyna-CLUE) under baseline conditions (continued current...

Sun and Shade leaves, SIF, and Photosynthetic Capacity

NASA Astrophysics Data System (ADS)

Berry, J. A.; Badgley, G.

2016-12-01

Recent advances in retrieval of solar induced chlorophyll fluorescence (SIF) have opened up new possibilities for remote sensing of canopy physiology and structure. To date most of the emphasis has been placed on SIF as an indicator of stress and photosynthetic capacity. However, it is clear that canopy structure can also have an influence. To this point, simulations of SIF in land surface models tend to under predict observed variation in SIF. Also, large, systematic differences in SIF from different canopy types seem to correlate well with the photosynthetic capacity of these canopies. SIF emissions from pampered crops can be several-fold that from evergreen, needle-leaf forests. Yet, these may have similar vegetation indices and absorb a similar fraction of incident PAR. SIF photons produced in a conifer canopy do have a lower probability of escaping its dense, clumped foliage. However, this does not explain the correlated differences in photosynthetic rate and SIF. It is useful, in this regard, to consider the separate contributions of sun and shade leaves to the SIF emitted by a canopy. Sun leaves tend to be displayed to intercept the direct solar beam, and these highly illuminated leaves are often visible from above the canopy. Sun leaves produce more SIF and a large fraction of it escapes. Therefore, the intensity of SIF may be a sensitive indicator of the partitioning of absorbed PAR to sun and shade leaves. Many models account tor the different photosynthetic capacity of sun and shade leaves in calculating canopy responses. However, the fraction of leaves in each category is usually parameterized by an assumed leaf angle distribution (e.g. spherical). In reality, the sun/shade fraction can vary over a wide range, and it has been difficult to measure. SIF and possibly near-IR reflectance of canopies can be used to specify this key parameter with obvious importance to understanding photosynthetic rate.

Canopy Spectral Invariants. Part 2; Application to Classification of Forest Types from Hyperspectral Data

NASA Technical Reports Server (NTRS)

Schull, M. A.; Knyazikhin, Y.; Xu, L.; Samanta, A.; Carmona, P. L.; Lepine, L.; Jenkins, J. P.; Ganguly, S.; Myneni, R. B.

2011-01-01

Many studies have been conducted to demonstrate the ability of hyperspectral data to discriminate plant dominant species. Most of them have employed the use of empirically based techniques, which are site specific, requires some initial training based on characteristics of known leaf and/or canopy spectra and therefore may not be extendable to operational use or adapted to changing or unknown land cover. In this paper we propose a physically based approach for separation of dominant forest type using hyperspectral data. The radiative transfer theory of canopy spectral invariants underlies the approach, which facilitates parameterization of the canopy reflectance in terms of the leaf spectral scattering and two spectrally invariant and structurally varying variables - recollision and directional escape probabilities. The methodology is based on the idea of retrieving spectrally invariant parameters from hyperspectral data first, and then relating their values to structural characteristics of three-dimensional canopy structure. Theoretical and empirical analyses of ground and airborne data acquired by Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) over two sites in New England, USA, suggest that the canopy spectral invariants convey information about canopy structure at both the macro- and micro-scales. The total escape probability (one minus recollision probability) varies as a power function with the exponent related to the number of nested hierarchical levels present in the pixel. Its base is a geometrical mean of the local total escape probabilities and accounts for the cumulative effect of canopy structure over a wide range of scales. The ratio of the directional to the total escape probability becomes independent of the number of hierarchical levels and is a function of the canopy structure at the macro-scale such as tree spatial distribution, crown shape and size, within-crown foliage density and ground cover. These properties allow for the natural separation of dominant forest classes based on the location of points on the total escape probability vs the ratio log-log plane.

WREP: A wavelet-based technique for extracting the red edge position from reflectance spectra for estimating leaf and canopy chlorophyll contents of cereal crops

NASA Astrophysics Data System (ADS)

Li, Dong; Cheng, Tao; Zhou, Kai; Zheng, Hengbiao; Yao, Xia; Tian, Yongchao; Zhu, Yan; Cao, Weixing

2017-07-01

Red edge position (REP), defined as the wavelength of the inflexion point in the red edge region (680-760 nm) of the reflectance spectrum, has been widely used to estimate foliar chlorophyll content from reflectance spectra. A number of techniques have been developed for REP extraction in the past three decades, but most of them require data-specific parameterization and the consistence of their performance from leaf to canopy levels remains poorly understood. In this study, we propose a new technique (WREP) to extract REPs based on the application of continuous wavelet transform to reflectance spectra. The REP is determined by the zero-crossing wavelength in the red edge region of a wavelet transformed spectrum for a number of scales of wavelet decomposition. The new technique is simple to implement and requires no parameterization from the user as long as continuous wavelet transforms are applied to reflectance spectra. Its performance was evaluated for estimating leaf chlorophyll content (LCC) and canopy chlorophyll content (CCC) of cereal crops (i.e. rice and wheat) and compared with traditional techniques including linear interpolation, linear extrapolation, polynomial fitting and inverted Gaussian. Our results demonstrated that WREP obtained the best estimation accuracy for both LCC and CCC as compared to traditional techniques. High scales of wavelet decomposition were favorable for the estimation of CCC and low scales for the estimation of LCC. The difference in optimal scale reveals the underlying mechanism of signature transfer from leaf to canopy levels. In addition, crop-specific models were required for the estimation of CCC over the full range. However, a common model could be built with the REPs extracted with Scale 5 of the WREP technique for wheat and rice crops when CCC was less than 2 g/m2 (R2 = 0.73, RMSE = 0.26 g/m2). This insensitivity of WREP to crop type indicates the potential for aerial mapping of chlorophyll content between growth seasons of cereal crops. The new REP extraction technique provides us a new insight for understanding the spectral changes in the red edge region in response to chlorophyll variation from leaf to canopy levels.

How many trees are enough? Tree death and the urban canopy

Treesearch

Lara A. Roman

2014-01-01

Massive city tree planting campaigns have invigorated the urban forestry movement, and engaged politicians, planners, and the public in urban greening. Million tree initiatives have been launched in Los Angeles, CA; Denver, CO; New York City, NY; Philadelphia, PA, and other cities. Sacramento, CA even has a five million tree program. These...

Assessing urban forest effects and values, Chicago's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Cherie Leblanc Fisher

2010-01-01

An analysis of trees in Chicago, IL, reveals that this city has about 3,585,000 trees with canopies that cover 17.2 percent of the area. The most common tree species are white ash, mulberry species, green ash, and tree-of-heaven. Chicago's urban forest currently stores about 716,000 tons of carbon...

Modeling canopy-level productivity: is the "big-leaf" simplification acceptable?

NASA Astrophysics Data System (ADS)

Sprintsin, M.; Chen, J. M.

2009-05-01

The "big-leaf" approach to calculating the carbon balance of plant canopies assumes that canopy carbon fluxes have the same relative responses to the environment as any single unshaded leaf in the upper canopy. Widely used light use efficiency models are essentially simplified versions of the big-leaf model. Despite its wide acceptance, subsequent developments in the modeling of leaf photosynthesis and measurements of canopy physiology have brought into question the assumptions behind this approach showing that big leaf approximation is inadequate for simulating canopy photosynthesis because of the additional leaf internal control on carbon assimilation and because of the non-linear response of photosynthesis on leaf nitrogen and absorbed light, and changes in leaf microenvironment with canopy depth. To avoid this problem a sunlit/shaded leaf separation approach, within which the vegetation is treated as two big leaves under different illumination conditions, is gradually replacing the "big-leaf" strategy, for applications at local and regional scales. Such separation is now widely accepted as a more accurate and physiologically based approach for modeling canopy photosynthesis. Here we compare both strategies for Gross Primary Production (GPP) modeling using the Boreal Ecosystem Productivity Simulator (BEPS) at local (tower footprint) scale for different land cover types spread over North America: two broadleaf forests (Harvard, Massachusetts and Missouri Ozark, Missouri); two coniferous forests (Howland, Maine and Old Black Spruce, Saskatchewan); Lost Creek shrubland site (Wisconsin) and Mer Bleue petland (Ontario). BEPS calculates carbon fixation by scaling Farquhar's leaf biochemical model up to canopy level with stomatal conductance estimated by a modified version of the Ball-Woodrow-Berry model. The "big-leaf" approach was parameterized using derived leaf level parameters scaled up to canopy level by means of Leaf Area Index. The influence of sunlit/shaded leaf separation on GPP prediction was evaluated accounting for the degree of the deviation of 3-dimensional leaf spatial distribution from the random case. More specifically, we compared and evaluated the behavior of both models showing the advantages of sunlit/shaded leaf separation strategy over a simplified big-leaf approach. Keywords: canopy photosynthesis, leaf area index, clumping index, remote sensing.

Green Infrastructure Increases Biogeochemical Responsiveness, Vegetation Growth and Decreases Runoff in a Semi-Arid City, Tucson, AZ, USA

NASA Astrophysics Data System (ADS)

Meixner, T.; Papuga, S. A.; Luketich, A. M.; Rockhill, T.; Gallo, E. L.; Anderson, J.; Salgado, L.; Pope, K.; Gupta, N.; Korgaonkar, Y.; Guertin, D. P.

2017-12-01

Green Infrastructure (GI) is often viewed as a mechanism to minimize the effects of urbanization on hydrology, water quality, and other ecosystem services (including the urban heat island). Quantifying the effects of GI requires field measurements of the dimensions of biogeochemical, ecosystem, and hydrologic function that we expect GI to impact. Here we investigated the effect of GI features in Tucson, Arizona which has a low intensity winter precipitation regime and a high intensity summer regime. We focused on understanding the effect of GI on soil hydraulic and biogeochemical properties as well as the effect on vegetation and canopy temperature. Our results demonstrate profound changes in biogeochemical and hydrologic properties and vegetation growth between GI systems and nearby control sites. In terms of hydrologic properties GI soils had increased water holding capacity and hydraulic conductivity. GI soils also have higher total carbon, total nitrogen, and organic matter in general than control soils. Furthermore, we tested the sampled soils (control and GI) for differences in biogeochemical response upon wetting. GI soils had larger respiration responses indicating greater biogeochemical activity overall. Long-term Lidar surveys were used to investigate the differential canopy growth of GI systems versus control sites. The results of this analysis indicate that while a significant amount of time is needed to observe differences in canopy growth GI features due increase tree size and thus likely impact street scale ambient temperatures. Additionally monitoring of transpiration, soil moisture, and canopy temperature demonstrates that GI features increase vegetation growth and transpiration and reduce canopy temperatures. These biogeochemical and ecohydrologic results indicate that GI can increase the biogeochemical processing of soils and increase tree growth and thus reduce urban ambient temperatures.

Aerial dispersal of particles emitted inside plant canopies: Application to the spread of plant diseases

NASA Astrophysics Data System (ADS)

Pan, Ying

This work combines numerical, experimental, and theoretical methods to investigate the dispersion of particles inside and above plant canopies. The large-eddy simulation (LES) approach is used to reproduce turbulence statistics and three-dimensional particle dispersion within the canopy roughness sublayer. The Eulerian description of conservation laws of fluid momentum and particle concentration implies that the continuous concentration field is advected by the continuous flow field. Within the canopy, modifications are required for the filtered momentum and concentration equations, because spatial filtering of flow variables and concentration field is inapplicable to a control volume consisting of both fluid and solid elements. In this work, the canopy region is viewed as a space occupied by air only. The sink of airflow momentum induced by forces acting on the surfaces of canopy elements is parameterized as a non-conservative virtual body force that dissipates the kinetic energy of the air. This virtual body force must reflect the characteristic of the surface forces exerted by canopy elements within the control volume, and is parameterized as a "drag force" following standard practice in LES studies. Specifically, the "drag force" is calculated as a product of a drag coefficient, the projected leaf area density, and the square of velocity. Using a constant drag coefficient, this model allows first-order accuracy in reproducing the vertically integrated sink of momentum within the canopy layer for airflows of high Reynolds number. The corresponding LES results of first- and second-order turbulence statistics are in good agreement with experimental data obtained in the field interior, within and just above mature maize canopies. However, the distribution of momentum sink among weak and strong events has not been well reproduced, inferred from the significant underestition of streamwise and vertical velocity skewness as well as the fractions of vertical momentum flux transported by strong events. Using a velocity-dependent drag coefficient that accounts for the effect of plant reconfiguration, the "drag force" model leads to LES results of streamwise and vertical velocity skewness as well as the fractions of vertical momentum flux transported by strong events in better agreement with field experimental data. The link between plant reconfiguration and turbulence dynamics within the canopy roughness sublayer is further investigated. The "reconfiguration drag model" using velocity-dependent drag coefficient is revised to incorporate a theoretical model of the force balance on individual crosswind blades. In the LES, the dimension and degree of the reconfiguration of canopy elements affect the magnitude and position of peak streamwise velocity skewness within the canopy as well as the fractions of vertical momentum flux transported by strong events. The streamwise velocity skewness is shown to be related to the penetration of strong events into the canopy, which is associated with the passage of canopy-scale coherent eddies. With the profile of mean vertical momentum flux constrained by field experimental data, changing the model of drag coefficient induces negligible changes in the vertically integrated "drag force" within the canopy layer. Consequently, first- and second-order turbulence statistics remain approximately the same. However, enhancing the rate of decrease of drag coefficient with increasing velocity increases the streamwise and vertical velocity skewness, the fractions of vertical momentum flux transported by strong events, as well as the ratio between vertical momentum flux transported by relatively strong head-down "sweeps" and relatively weak head-up "ejections." These results confirmed the inadequacy of describing the effects of canopy-scale coherent structures using just first- and second-order turbulence statistics. The filtered concentration equation is applied to the dispersion of particles within the canopy roughness sublayer, assuming that a virtual continuous concentration field is advected by a virtual continuous velocity field. A canopy deposition model is used to model the sink of particle concentration associated with the impaction, sedimentation, retention, and re-entrainment of particles on the surfaces of canopy elements. LES results of mean particle concentration field and mean ground deposition rate were evaluated against data obtained during an artificial continuous point-source release experiment. Accounting for the effect of reconfiguration by using a velocity dependent drag coefficient leads to better agreement between LES results and field experimental data of the mean particle concentration field, suggesting the importance of reproducing the distribution of momentum sink among weak and strong events for reproducing the dispersion of particles. LES results obtained using a velocity-dependent drag coefficient are analyzed to estimate essential properties for the occurrence of plant disease epidemics. The most interesting finding is that an existing analytical function can be used to model the crosswind-integrated mean concentration field above the canopy normalized by the escape fraction for particles released from the field interior. (Abstract shortened by ProQuest.).

Measuring urban tree loss dynamics across residential landscapes.

PubMed

Ossola, Alessandro; Hopton, Matthew E

2018-01-15

The spatial arrangement of urban vegetation depends on urban morphology and socio-economic settings. Urban vegetation changes over time because of human management. Urban trees are removed due to hazard prevention or aesthetic preferences. Previous research attributed tree loss to decreases in canopy cover. However, this provides little information about location and structural characteristics of trees lost, as well as environmental and social factors affecting tree loss dynamics. This is particularly relevant in residential landscapes where access to residential parcels for field surveys is limited. We tested whether multi-temporal airborne LiDAR and multi-spectral imagery collected at a 5-year interval can be used to investigate urban tree loss dynamics across residential landscapes in Denver, CO and Milwaukee, WI, covering 400,705 residential parcels in 444 census tracts. Position and stem height of trees lost were extracted from canopy height models calculated as the difference between final (year 5) and initial (year 0) vegetation height derived from LiDAR. Multivariate regression models were used to predict number and height of tree stems lost in residential parcels in each census tract based on urban morphological and socio-economic variables. A total of 28,427 stems were lost from residential parcels in Denver and Milwaukee over 5years. Overall, 7% of residential parcels lost one stem, averaging 90.87 stems per km 2 . Average stem height was 10.16m, though trees lost in Denver were taller compared to Milwaukee. The number of stems lost was higher in neighborhoods with higher canopy cover and developed before the 1970s. However, socio-economic characteristics had little effect on tree loss dynamics. The study provides a simple method for measuring urban tree loss dynamics within and across entire cities, and represents a further step toward high resolution assessments of the three-dimensional change of urban vegetation at large spatial scales. Published by Elsevier B.V.

Land cover characterization and land surface parameterization research

USGS Publications Warehouse

Steyaert, Louis T.; Loveland, Thomas R.; Parton, William J.

1997-01-01

The understanding of land surface processes and their parameterization in atmospheric, hydrologic, and ecosystem models has been a dominant research theme over the past decade. For example, many studies have demonstrated the key role of land cover characteristics as controlling factors in determining land surface processes, such as the exchange of water, energy, carbon, and trace gases between the land surface and the lower atmosphere. The requirements for multiresolution land cover characteristics data to support coupled-systems modeling have also been well documented, including the need for data on land cover type, land use, and many seasonally variable land cover characteristics, such as albedo, leaf area index, canopy conductance, surface roughness, and net primary productivity. Recently, the developers of land data have worked more closely with the land surface process modelers in these efforts.

Urban trees and the risk of poor birth outcomes

Treesearch

Geoffrey H. Donovan; Yvonne L. Michael; David T. Butry; Amy D. Sullivan; John M. Chase

2011-01-01

This paper investigated whether greater tree-canopy cover is associated with reduced risk of poor birth outcomes in Portland, Oregon. Residential addresses were geocoded and linked to classified-aerial imagery to calculate tree-canopy cover in 50, 100, and 200 m buffers around each home in our sample (n=5696). Detailed data on maternal characteristics and additional...

The structure, function and value of urban forests in California communities

Treesearch

E. Gregory McPherson; Qingfu Xiao; Natalie S. van Doorn; John de Goede; Jacquelyn Bjorkman; Allan Hollander; Ryan M. Boynton; James F. Quinn; James H. Thorne

2017-01-01

This study used tree data from field plots in urban areas to describe forest structure in urban areas throughout California. The plot data were used with numerical models to calculate several ecosystem services produced by trees. A series of transfer functions were calculated to scale-up results from the plots to the landscape using urban tree canopy (UTC) mapped at 1-...

Assessing urban forest effects and values, Scranton's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Vincent Cotrone

2010-01-01

An analysis of trees in the urbanized portion of Scranton, PA, reveals that this area has about 1.2 million trees with canopies that cover 22.0 percent of the area. The most common tree species are red maple, gray birch, black cherry, northern red oak, and quaking aspen. Scranton's urban forest currently store about 93,300 tons of carbon valued at $1.9 million. In...

Estimation of leaf area index and its sunlit portion from DSCOVR EPIC data: Theoretical basis

PubMed Central

Yang, Bin; Knyazikhin, Yuri; Mõttus, Matti; Rautiainen, Miina; Stenberg, Pauline; Yan, Lei; Chen, Chi; Yan, Kai; Choi, Sungho; Park, Taejin; Myneni, Ranga B.

2017-01-01

This paper presents the theoretical basis of the algorithm designed for the generation of leaf area index and diurnal course of its sunlit portion from NASA’s Earth Polychromatic Imaging Camera (EPIC) onboard NOAA’s Deep Space Climate Observatory (DSCOVR). The Look-up-Table (LUT) approach implemented in the MODIS operational LAI/FPAR algorithm is adopted. The LUT, which is the heart of the approach, has been significantly modified. First, its parameterization incorporates the canopy hot spot phenomenon and recent advances in the theory of canopy spectral invariants. This allows more accurate decoupling of the structural and radiometric components of the measured Bidirectional Reflectance Factor (BRF), improves scaling properties of the LUT and consequently simplifies adjustments of the algorithm for data spatial resolution and spectral band compositions. Second, the stochastic radiative transfer equations are used to generate the LUT for all biome types. The equations naturally account for radiative effects of the three-dimensional canopy structure on the BRF and allow for an accurate discrimination between sunlit and shaded leaf areas. Third, the LUT entries are measurable, i.e., they can be independently derived from both below canopy measurements of the transmitted and above canopy measurements of reflected radiation fields. This feature makes possible direct validation of the LUT, facilitates identification of its deficiencies and development of refinements. Analyses of field data on canopy structure and leaf optics collected at 18 sites in the Hyytiälä forest in southern boreal zone in Finland and hyperspectral images acquired by the EO-1 Hyperion sensor support the theoretical basis. PMID:28867834

HIGH-RESOLUTION DATASET OF URBAN CANOPY PARAMETERS FOR HOUSTON, TEXAS

EPA Science Inventory

Urban dispersion and air quality simulation models applied at various horizontal scales require different levels of fidelity for specifying the characteristics of the underlying surfaces. As the modeling scales approach the neighborhood level (~1 km horizontal grid spacing), the...

Modeling the formation and aging of secondary organic aerosols in Los Angeles during CalNex 2010

NASA Astrophysics Data System (ADS)

Hayes, P. L.; Carlton, A. G.; Baker, K. R.; Ahmadov, R.; Washenfelder, R. A.; Alvarez, S.; Rappenglück, B.; Gilman, J. B.; Kuster, W. C.; de Gouw, J. A.; Zotter, P.; Prévôt, A. S. H.; Szidat, S.; Kleindienst, T. E.; Offenberg, J. H.; Jimenez, J. L.

2014-12-01

Four different parameterizations for the formation and evolution of secondary organic aerosol (SOA) are evaluated using a 0-D box model representing the Los Angeles Metropolitan Region during the CalNex 2010 field campaign. We constrain the model predictions with measurements from several platforms and compare predictions with particle and gas-phase observations from the CalNex Pasadena ground site. That site provides a unique opportunity to study aerosol formation close to anthropogenic emission sources with limited recirculation. The model SOA formed only from the oxidation of VOCs (V-SOA) is insufficient to explain the observed SOA concentrations, even when using SOA parameterizations with multi-generation oxidation that produce much higher yields than have been observed in chamber experiments, or when increasing yields to their upper limit estimates accounting for recently reported losses of vapors to chamber walls. The Community Multiscale Air Quality (WRF-CMAQ) model (version 5.0.1) provides excellent predictions of secondary inorganic particle species but underestimates the observed SOA mass by a factor of 25 when an older VOC-only parameterization is used, which is consistent with many previous model-measurement comparisons for pre-2007 anthropogenic SOA modules in urban areas. Including SOA from primary semi-volatile and intermediate volatility organic compounds (P-S/IVOCs) following the parameterizations of Robinson et al. (2007), Grieshop et al. (2009), or Pye and Seinfeld (2010) improves model/measurement agreement for mass concentration. When comparing the three parameterizations, the Grieshop et al. (2009) parameterization more accurately reproduces both the SOA mass concentration and oxygen-to-carbon ratio inside the urban area. Our results strongly suggest that other precursors besides VOCs, such as P-S/IVOCs, are needed to explain the observed SOA concentrations in Pasadena. All the parameterizations over-predict urban SOA formation at long photochemical ages (≈ 3 days) compared to observations from multiple sites, which can lead to problems in regional and global modeling. Among the explicitly modeled VOCs, the precursor compounds that contribute the greatest SOA mass are methylbenzenes. Polycyclic aromatic hydrocarbons (PAHs) are less important precursors and contribute less than 4% of the SOA mass. The amounts of SOA mass from diesel vehicles, gasoline vehicles, and cooking emissions are estimated to be 16-27, 35-61, and 19-35%, respectively, depending on the parameterization used, which is consistent with the observed fossil fraction of urban SOA, 71 (±3) %. In-basin biogenic VOCs are predicted to contribute only a few percent to SOA. A regional SOA background of approximately 2.1 μg m-3 is also present due to the long distance transport of highly aged OA. The percentage of SOA from diesel vehicle emissions is the same, within the estimated uncertainty, as reported in previous work that analyzed the weekly cycles in OA concentrations (Bahreini et al., 2012; Hayes et al., 2013). However, the modeling work presented here suggests a strong anthropogenic source of modern carbon in SOA, due to cooking emissions, which was not accounted for in those previous studies. Lastly, this work adapts a simple two-parameter model to predict SOA concentration and O/C from urban emissions. This model successfully predicts SOA concentration, and the optimal parameter combination is very similar to that found for Mexico City. This approach provides a computationally inexpensive method for predicting urban SOA in global and climate models. We estimate pollution SOA to account for 26 Tg yr-1 of SOA globally, or 17% of global SOA, 1/3 of which is likely to be non-fossil.

Evaluation of four methods for estimating leaf area of isolated trees

Treesearch

P.J. Peper; E.G. McPherson

2003-01-01

The accurate modeling of the physiological and functional processes of urban forests requires information on the leaf area of urban tree species. Several non-destructive, indirect leaf area sampling methods have shown good performance for homogenous canopies. These methods have not been evaluated for use in urban settings where trees are typically isolated and...

Subpixel urban land cover estimation: comparing cubist, random forests, and support vector regression

Treesearch

Jeffrey T. Walton

2008-01-01

Three machine learning subpixel estimation methods (Cubist, Random Forests, and support vector regression) were applied to estimate urban cover. Urban forest canopy cover and impervious surface cover were estimated from Landsat-7 ETM+ imagery using a higher resolution cover map resampled to 30 m as training and reference data. Three different band combinations (...

COST 728 Project Report: Urbanization of Meteorological and Air Quality Models - Chapter 5 - Model Urbanization Strategy: Summaries, Recommendations and Requirements

EPA Science Inventory

The urban canopy (UC), the layer of the atmosphere between the ground and the top of the highest buildings, is the region where people live and human activities take place. Because of this importance (e.g., human health, preservation of buildings) significant efforts have been d...

A specific PFT and sub-canopy structure for simulating oil palm in the Community Land Model

NASA Astrophysics Data System (ADS)

Fan, Y.; Knohl, A.; Roupsard, O.; Bernoux, M.; LE Maire, G.; Panferov, O.; Kotowska, M.; Meijide, A.

2015-12-01

Towards an effort to quantify the effects of rainforests to oil palm conversion on land-atmosphere carbon, water and energy fluxes, a specific plant functional type (PFT) and sub-canopy structure are developed for simulating oil palm within the Community Land Model (CLM4.5). Current global land surface models only simulate annual crops beside natural vegetation. In this study, a multilayer oil palm subroutine is developed in CLM4.5 for simulating oil palm's phenology and carbon and nitrogen allocation. The oil palm has monopodial morphology and sequential phenology of around 40 stacked phytomers, each carrying a large leaf and a fruit bunch, forming a natural multilayer canopy. A sub-canopy phenological and physiological parameterization is thus introduced, so that multiple phytomer components develop simultaneously but according to their different phenological steps (growth, yield and senescence) at different canopy layers. This specific multilayer structure was proved useful for simulating canopy development in terms of leaf area index (LAI) and fruit yield in terms of carbon and nitrogen outputs in Jambi, Sumatra (Fan et al. 2015). The study supports that species-specific traits, such as palm's monopodial morphology and sequential phenology, are necessary representations in terrestrial biosphere models in order to accurately simulate vegetation dynamics and feedbacks to climate. Further, oil palm's multilayer structure allows adding all canopy-level calculations of radiation, photosynthesis, stomatal conductance and respiration, beside phenology, also to the sub-canopy level, so as to eliminate scale mismatch problem among different processes. A series of adaptations are made to the CLM model. Initial results show that the adapted multilayer radiative transfer scheme and the explicit represention of oil palm's canopy structure improve on simulating photosynthesis-light response curve. The explicit photosynthesis and dynamic leaf nitrogen calculations per canopy layer also enhance simulated CO2 flux when compared to eddy covariance flux data. More investigations on energy and water fluxes and nitrogen balance are being conducted. These new schemes would hopefully promote the understanding of climatic effects of the tropical land use transformation system.

Webinar Announcement - The Clean Water State Revolving Fund: Flexible Funding for the Urban Tree Canopy

EPA Pesticide Factsheets

This webinar, presented by the EPA and USDA, explores how the CWSRF can be used as a funding source for green infrastructure and urban forestry projects—a cost effective way to reduce combined sewage flooding problems.

High-resolution tree canopy mapping for New York City using LIDAR and object-based image analysis

NASA Astrophysics Data System (ADS)

MacFaden, Sean W.; O'Neil-Dunne, Jarlath P. M.; Royar, Anna R.; Lu, Jacqueline W. T.; Rundle, Andrew G.

2012-01-01

Urban tree canopy is widely believed to have myriad environmental, social, and human-health benefits, but a lack of precise canopy estimates has hindered quantification of these benefits in many municipalities. This problem was addressed for New York City using object-based image analysis (OBIA) to develop a comprehensive land-cover map, including tree canopy to the scale of individual trees. Mapping was performed using a rule-based expert system that relied primarily on high-resolution LIDAR, specifically its capacity for evaluating the height and texture of aboveground features. Multispectral imagery was also used, but shadowing and varying temporal conditions limited its utility. Contextual analysis was a key part of classification, distinguishing trees according to their physical and spectral properties as well as their relationships to adjacent, nonvegetated features. The automated product was extensively reviewed and edited via manual interpretation, and overall per-pixel accuracy of the final map was 96%. Although manual editing had only a marginal effect on accuracy despite requiring a majority of project effort, it maximized aesthetic quality and ensured the capture of small, isolated trees. Converting high-resolution LIDAR and imagery into usable information is a nontrivial exercise, requiring significant processing time and labor, but an expert system-based combination of OBIA and manual review was an effective method for fine-scale canopy mapping in a complex urban environment.

Plant leaf traits, canopy processes, and global atmospheric chemistry interactions.

NASA Astrophysics Data System (ADS)

Guenther, A. B.

2017-12-01

Plants produce and emit a diverse array of volatile metabolites into the atmosphere that participate in chemical reactions that influence distributions of air pollutants and short-lived climate forcers including organic aerosol, ozone and methane. It is now widely accepted that accurate estimates of these emissions are required as inputs for regional air quality and global climate models. Predicting these emissions is complicated by the large number of volatile organic compounds, driving variables (e.g., temperature, solar radiation, abiotic and biotic stresses) and processes operating across a range of scales. Modeling efforts to characterize emission magnitude and variations will be described along with an assessment of the observations available for parameterizing and evaluating these models including discussion of the limitations and challenges associated with existing model approaches. A new approach for simulating canopy scale organic emissions on regional to global scales will be described and compared with leaf, canopy and regional scale flux measurements. The importance of including additional compounds and processes as well as improving estimates of existing ones will also be discussed.

Modeling ozone uptake by urban and peri-urban forest: a case study in the Metropolitan City of Rome.

PubMed

Fusaro, Lina; Mereu, Simone; Salvatori, Elisabetta; Agliari, Elena; Fares, Silvano; Manes, Fausto

2018-03-01

Urban and peri-urban forests are green infrastructures (GI) that play a substantial role in delivering ecosystem services such as the amelioration of air quality by the removal of air pollutants, among which is ozone (O 3 ), which is the most harmful pollutant in Mediterranean metropolitan areas. Models may provide a reliable estimate of gas exchanges between vegetation and atmosphere and are thus a powerful tool to quantify and compare O 3 removal in different contexts. The present study modeled the O 3 stomatal uptake at canopy level of an urban and a peri-urban forest in the Metropolitan City of Rome in two different years. Results show different rates of O 3 fluxes between the two forests, due to different exposure to the pollutant, management practice effects on forest structure and functionality, and environmental conditions, namely, different stressors affecting the gas exchange rates of the two GIs. The periodic components of the time series calculated by means of the spectral analysis show that seasonal variation of modeled canopy transpiration is driven by precipitation in peri-urban forests, whereas in the urban forest seasonal variations are driven by vapor pressure deficit of ambient air. Moreover, in the urban forest high water availability during summer months, owing to irrigation practice, leads to an increase in O 3 uptake, thus suggesting that irrigation may enhance air phytoremediation in urban areas.

A Backward-Lagrangian-Stochastic Footprint Model for the Urban Environment

NASA Astrophysics Data System (ADS)

Wang, Chenghao; Wang, Zhi-Hua; Yang, Jiachuan; Li, Qi

2018-02-01

Built terrains, with their complexity in morphology, high heterogeneity, and anthropogenic impact, impose substantial challenges in Earth-system modelling. In particular, estimation of the source areas and footprints of atmospheric measurements in cities requires realistic representation of the landscape characteristics and flow physics in urban areas, but has hitherto been heavily reliant on large-eddy simulations. In this study, we developed physical parametrization schemes for estimating urban footprints based on the backward-Lagrangian-stochastic algorithm, with the built environment represented by street canyons. The vertical profile of mean streamwise velocity is parametrized for the urban canopy and boundary layer. Flux footprints estimated by the proposed model show reasonable agreement with analytical predictions over flat surfaces without roughness elements, and with experimental observations over sparse plant canopies. Furthermore, comparisons of canyon flow and turbulence profiles and the subsequent footprints were made between the proposed model and large-eddy simulation data. The results suggest that the parametrized canyon wind and turbulence statistics, based on the simple similarity theory used, need to be further improved to yield more realistic urban footprint modelling.

Effective Albedo of Vegetated Terrain at L-Band

NASA Technical Reports Server (NTRS)

Kurum, Mehmet; O'Neill, Peggy E.; Lang, Roger H.

2011-01-01

This paper derives an explicit expression for an effective albedo of vegetated terrain from the zero- and multiple- order radiative transfer (RT) model comparison. The formulation establishes a direct physical link between the effective vegetation parameterization and the theoretical description of absorption and scattering within the canopy. The paper will present an evaluation of the derived albedo for corn canopies with data taken during an experiment at Alabama A&M Winfield A. Thomas Agricultural Research Station near Huntsville, Alabama in June, 1998. The test site consisted of two 50-m x 60-m plots - one with a bare surface and the other with grass cover - and four 30-m x 50-m plots of corn at different planting densities. One corn field was planted at a full density of 9.5 plants/sq m while the others were planted at 1/3, 1/2 and 2/3 of the full density. The fields were observed with a truck-mounted L-band radiometer at incident angle of 15 degree for the period of two weeks. Soil moisture (SM) changed daily due to irrigation and natural rainfall. Variations in gravimetric SM from 18 % to 34 % were seen during this period. Ground truth data, including careful characterization of the corn size and orientation statistics, and its dielectric, was also collected and used to simulate the effective albedo for the vegetation. The single-scattering albedo is defined as the fractional power scattered from individual vegetation constituents with respect to canopy extinction. It represents single-scattering properties of vegetation elements only, and is independent of ground properties. The values of the albedo get higher when there is dense vegetation (i.e. forest, mature corn, etc.) with scatterers, such as branches and trunks (or stalks in the case of corn), which are large with respect to the wavelength. This large albedo leads to a reduction in brightness temperature in the zero-order RT solution (known as tau-omega model). Higher-order multiple-scattering RT solutions are required for proper representation of scattering within vegetation. In this paper, an expression for an effective albedo for the whole canopy including the ground is derived for use in the zero-order RT model-based SM retrieval. This effective albedo takes into account of all the processes taking place within the canopy, including multiple-scattering. This new formulation will be presented and its importance for microwave SM retrieval will be evaluated for corn canopies in conjunction with the detailed ground truth data obtained during the experiment at Alabama in 1998. Emphasis will be placed on examining how the radiometer response to SM is modified by the corn canopy scattering under different field conditions. A semi-empirical parameterization of the effective albedo will be investigated through analysis of SM and vegetation water content effects on the effective albedo.

Model Urbanization Strategy: Summaries, Recommendations and Requirements

EPA Science Inventory

The urban canopy (UC), the layer of the atmosphere between the ground and the top of the highest buildings, is the region where people live and human activities take place. Because of this importance (e.g., human health, preservation of buildings) significant efforts have been de...

Reducing uncertainty for estimating forest carbon stocks and dynamics using integrated remote sensing, forest inventory and process-based modeling

NASA Astrophysics Data System (ADS)

Poulter, B.; Ciais, P.; Joetzjer, E.; Maignan, F.; Luyssaert, S.; Barichivich, J.

2015-12-01

Accurately estimating forest biomass and forest carbon dynamics requires new integrated remote sensing, forest inventory, and carbon cycle modeling approaches. Presently, there is an increasing and urgent need to reduce forest biomass uncertainty in order to meet the requirements of carbon mitigation treaties, such as Reducing Emissions from Deforestation and forest Degradation (REDD+). Here we describe a new parameterization and assimilation methodology used to estimate tropical forest biomass using the ORCHIDEE-CAN dynamic global vegetation model. ORCHIDEE-CAN simulates carbon uptake and allocation to individual trees using a mechanistic representation of photosynthesis, respiration and other first-order processes. The model is first parameterized using forest inventory data to constrain background mortality rates, i.e., self-thinning, and productivity. Satellite remote sensing data for forest structure, i.e., canopy height, is used to constrain simulated forest stand conditions using a look-up table approach to match canopy height distributions. The resulting forest biomass estimates are provided for spatial grids that match REDD+ project boundaries and aim to provide carbon estimates for the criteria described in the IPCC Good Practice Guidelines Tier 3 category. With the increasing availability of forest structure variables derived from high-resolution LIDAR, RADAR, and optical imagery, new methodologies and applications with process-based carbon cycle models are becoming more readily available to inform land management.

Neighbourhood-scale urban forest ecosystem classification.

PubMed

Steenberg, James W N; Millward, Andrew A; Duinker, Peter N; Nowak, David J; Robinson, Pamela J

2015-11-01

Urban forests are now recognized as essential components of sustainable cities, but there remains uncertainty concerning how to stratify and classify urban landscapes into units of ecological significance at spatial scales appropriate for management. Ecosystem classification is an approach that entails quantifying the social and ecological processes that shape ecosystem conditions into logical and relatively homogeneous management units, making the potential for ecosystem-based decision support available to urban planners. The purpose of this study is to develop and propose a framework for urban forest ecosystem classification (UFEC). The multifactor framework integrates 12 ecosystem components that characterize the biophysical landscape, built environment, and human population. This framework is then applied at the neighbourhood scale in Toronto, Canada, using hierarchical cluster analysis. The analysis used 27 spatially-explicit variables to quantify the ecosystem components in Toronto. Twelve ecosystem classes were identified in this UFEC application. Across the ecosystem classes, tree canopy cover was positively related to economic wealth, especially income. However, education levels and homeownership were occasionally inconsistent with the expected positive relationship with canopy cover. Open green space and stocking had variable relationships with economic wealth and were more closely related to population density, building intensity, and land use. The UFEC can provide ecosystem-based information for greening initiatives, tree planting, and the maintenance of the existing canopy. Moreover, its use has the potential to inform the prioritization of limited municipal resources according to ecological conditions and to concerns of social equity in the access to nature and distribution of ecosystem service supply. Copyright © 2015 Elsevier Ltd. All rights reserved.

Patterns in understory woody diversity and soil nitrogen across native- and non-native-urban tropical forests

Treesearch

D.F. Cusack; T.L. McCleery; NO-VALUE

2014-01-01

Urban expansion is accelerating in the tropics, and may promote the spread of introduced plant species into urban-proximate forests. For example, soil disturbance can deplete the naturally high soil nitrogen pools in wet tropical soils, favoring introduced species with nitrogen-fixing capabilities. Also, forest fragmentation and canopy disturbance are likely to favor...

Assessing urban forest effects and values: Morgantown's Urban Forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jonathan Cumming; Sandhya Mohen; Anne Buckelew. Cumming

2012-01-01

An analysis of the community forest in Morgantown, WV, was undertaken in 2004 to characterize the structural and functional attributes of this forest resource. The assessment revealed that this city has about 658,000 trees with canopies that cover 35.5 percent of the area. The most common tree species are sugar maple, black cherry, and hawthorn. The urban forest...

NEIGHBORHOOD SCALE AIR QUALITY MODELING IN HOUSTON USING URBAN CANOPY PARAMETERS IN MM5 AND CMAQ WITH IMPROVED CHARACTERIZATION OF MESOSCALE LAKE-LAND BREEZE CIRCULATION

EPA Science Inventory

Advanced capability of air quality simulation models towards accurate performance at finer scales will be needed for such models to serve as tools for performing exposure and risk assessments in urban areas. It is recognized that the impact of urban features such as street and t...

Growing the urban forest: tree performance in response to biotic and abiotic land management

Treesearch

Emily E. Oldfield; Alexander J. Felson; D. S. Novem Auyeung; Thomas W. Crowther; Nancy F. Sonti; Yoshiki Harada; Daniel S. Maynard; Noah W. Sokol; Mark S. Ashton; Robert J. Warren; Richard A. Hallett; Mark A. Bradford

2015-01-01

Forests are vital components of the urban landscape because they provide ecosystem services such as carbon sequestration, storm-water mitigation, and air-quality improvement. To enhance these services, cities are investing in programs to create urban forests. A major unknown, however, is whether planted trees will grow into the mature, closed-canopied forest on which...

Trees and Streets as Drivers of Urban Stormwater Nutrient Pollution.

PubMed

Janke, Benjamin D; Finlay, Jacques C; Hobbie, Sarah E

2017-09-05

Expansion of tree cover is a major management goal in cities because of the substantial benefits provided to people, and potentially to water quality through reduction of stormwater volume by interception. However, few studies have addressed the full range of potential impacts of trees on urban runoff, which includes deposition of nutrient-rich leaf litter onto streets connected to storm drains. We analyzed the influence of trees on stormwater nitrogen and phosphorus export across 19 urban watersheds in Minneapolis-St. Paul, MN, U.S.A., and at the scale of individual streets within one residential watershed. Stormwater nutrient concentrations were highly variable across watersheds and strongly related to tree canopy over streets, especially for phosphorus. Stormwater nutrient loads were primarily related to road density, the dominant control over runoff volume. Street canopy exerted opposing effects on loading, where elevated nutrient concentrations from trees near roads outweighed the weak influence of trees on runoff reduction. These results demonstrate that vegetation near streets contributes substantially to stormwater nutrient pollution, and therefore to eutrophication of urban surface waters. Urban landscape design and management that account for trees as nutrient pollution sources could improve water quality outcomes, while allowing cities to enjoy the myriad benefits of urban forests.

Application of WRF/Chem-MADRID and WRF/Polyphemus in Europe - Part 1: Model description, evaluation of meteorological predictions, and aerosol-meteorology interactions

NASA Astrophysics Data System (ADS)

Zhang, Y.; Sartelet, K.; Wu, S.-Y.; Seigneur, C.

2013-07-01

Comprehensive model evaluation and comparison of two 3-D air quality modeling systems (i.e., the Weather Research and Forecast model (WRF)/Polyphemus and WRF with chemistry and the Model of Aerosol Dynamics, Reaction, Ionization, and Dissolution (MADRID) (WRF/Chem-MADRID)) are conducted over Western Europe. Part 1 describes the background information for the model comparison and simulation design, the application of WRF for January and July 2001 over triple-nested domains in Western Europe at three horizontal grid resolutions: 0.5°, 0.125°, and 0.025°, and the effect of aerosol/meteorology interactions on meteorological predictions. Nine simulated meteorological variables (i.e., downward shortwave and longwave radiation fluxes (SWDOWN and LWDOWN), outgoing longwave radiation flux (OLR), temperature at 2 m (T2), specific humidity at 2 m (Q2), relative humidity at 2 m (RH2), wind speed at 10 m (WS10), wind direction at 10 m (WD10), and precipitation (Precip)) are evaluated using available observations in terms of spatial distribution, domainwide daily and site-specific hourly variations, and domainwide performance statistics. The vertical profiles of temperature, dew points, and wind speed/direction are also evaluated using sounding data. WRF demonstrates its capability in capturing diurnal/seasonal variations and spatial gradients and vertical profiles of major meteorological variables. While the domainwide performance of LWDOWN, OLR, T2, Q2, and RH2 at all three grid resolutions is satisfactory overall, large positive or negative biases occur in SWDOWN, WS10, and Precip even at 0.125° or 0.025° in both months and in WD10 in January. In addition, discrepancies between simulations and observations exist in T2, Q2, WS10, and Precip at mountain/high altitude sites and large urban center sites in both months, in particular, during snow events or thunderstorms. These results indicate the model's difficulty in capturing meteorological variables in complex terrain and subgrid-scale meteorological phenomena, due to inaccuracies in model initialization parameterization (e.g., lack of soil temperature and moisture nudging), limitations in the physical parameterizations (e.g., shortwave radiation, cloud microphysics, cumulus parameterizations, and ice nucleation treatments) as well as limitations in surface heat and moisture budget parameterizations (e.g., snow-related processes, subgrid-scale surface roughness elements, and urban canopy/heat island treatments and CO2 domes). While the use of finer grid resolutions of 0.125° and 0.025° shows some improvements for WS10, WD10, Precip, and some mesoscale events (e.g., strong forced convection and heavy precipitation), it does not significantly improve the overall statistical performance for all meteorological variables except for Precip. The WRF/Chem simulations with and without aerosols show that aerosols lead to reduced net shortwave radiation fluxes, 2 m temperature, 10 m wind speed, planetary boundary layer (PBL) height, and precipitation and increase aerosol optical depth, cloud condensation nuclei, cloud optical depth, and cloud droplet number concentrations over most of the domain. These results indicate a need to further improve the model representations of the above parameterizations as well as aerosol-meteorology interactions at all scales.

Evaluate the urban effect on summer convective precipitation by coupling a urban canopy model with a Regional Climate Model

NASA Astrophysics Data System (ADS)

Liu, Z.; Liu, S.; Xue, Y.; Oleson, K. W.

2013-12-01

One of the most significant urbanization in the world occurred in Great Beijing Area of China during the past several decades. The land use and land cover changes modifies the land surface physical characteristics, including the anthropogenic heat and thermo-dynamic conduction. All of those play important roles in the urban regional climate changes. We developed a single layer urban canopy module based on the Community Land Surface Model Urban Module (CLMU). We have made further improvements in the urban module: the energy balances on the five surface conditions are considered separately: building roof, sun side and shade side wall, pervious and impervious land surface. Over each surface, a method to calculate sky view factor (SVF) is developed based on the physically process while most urban models simply provide an empirical value; A new scheme for calculating the latent heat flux is applied on both wall and impervious land; anthropogenic heat is considered in terms of industrial production, domestic wastes, vehicle and air condition. All of these developments improve the accuracy of surface energy balance processing in urban area. The urban effect on summer convective precipitation under the unstable atmospheric condition in the Great Beijing Area was investigated by simulating a heavy rainfall event in July 21st 2012. In this storm, strong meso-scale convective complexes (MCC) brought precipitation of averagely 164 mm within 6 hours, which is the record of past 60 years in the region. Numerical simulating experiment was set up by coupling MCLMU with WRF. Several condition/blank control cases were also set up. The horizontal resolution in all simulations was 2 km. While all of the control results drastically underestimate the urban precipitation, the result of WRF-MCLMU is much closer to the observation though still underestimated. More sensitive experiments gave a preliminary conclusion of how the urban canopy physics processing affects the local precipitation: the existence of large area of impervious surfaces restrain the surface evaporation and latent heat flux in urban while the anthropogenic heat and enhanced sensible heat flux warm up the lower atmospheric layer and strengthen the vertical stratification instability; In this storm event, the water supply of the MCC was thought to be sufficient, thus the instability of the vertical stratification was the key factor for precipitation.

Albedo and its Relationship to Land Cover and the Urban Heat Island in the Boston Metropolitan Region

NASA Astrophysics Data System (ADS)

Trlica, A.; Hutyra, L.; Wang, J.; Schaaf, C.; Erb, A.

2016-12-01

The urban built environment creates key changes in the biophysical character of the landscape, including the creation of Urban Heat Islands (UHIs) with increased near-surface temperatures in and around cities. Alteration in surface albedo is believed to partially drive UHIs through greater absorption of solar energy, but few empirical studies have specifically quantified albedo across a heterogeneous urban landscape, or investigated linkages between albedo, the UHI, and other surface socio-biophysical characteristics at a high enough spatial resolution to discern urban-scale features. This study used data derived from observations by Landsat and other remote sensing platforms to measure albedo across a varied urban landscape centered on Boston, Massachusetts, and examined the relationship between albedo, several key indicators of urban surface character (canopy cover, impervious fraction, and population density) and land surface temperature at resolutions of both 30 and 500 m. Albedo tended to be lower in areas with highest urbanization intensity indicators compared to rural undeveloped areas, and areas with lower albedo tended also to have higher median daytime summer surface temperatures. A k-means classification utilizing all the data available for each pixel revealed several distinct patterns of urban land cover corresponding mainly to the density of population and constructed surfaces and their impact on tree canopy cover. Mean 30-m summer surface temperatures ranged from 40.0 °C (SD = 2.6) in urban core areas to 26.2 °C (SD = 1.1) in nearby forest, but we only observed correspondingly large albedo decreases in the highest density urban core, with mean albedo of 0.116 (SD = 0.015) compared with 0.155 (SD = 0.015) in forest. Observations show that lower albedo in the Boston metropolitan region may be an important component of the local UHI in the most densely built-up urban core regions, while the UHI temperature effect in less densely settled peripheral regions is more likely to be driven primarily by reduced evapotranspiration due to diminished tree canopy and greater impervious surface coverage. These results empirically characterize surface albedo across a suite of land cover categories and biophysical characteristics and reveal how albedo relates to surface temperatures in this urbanized region.

Inclusion of an ultraviolet radiation transfer component in an urban forest effects model for predicting tree influences on potential below-canopy exposure to UVB radiation

Treesearch

Gordon M. Heisler; Richard H. Grant; David J. Nowak; Wei Gao; Daniel E. Crane; Jeffery T. Walton

2003-01-01

Evaluating the impact of ultraviolet-B radiation (UVB) on urban populations would be enhanced by improved predictions of the UVB radiation at the level of human activity. This paper reports the status of plans for incorporating a UVB prediction module into an existing Urban Forest Effects (UFORE) model. UFORE currently has modules to quantify urban forest structure,...

Exploring a new method for the retrieval of urban thermophysical properties using thermal infrared remote sensing and deterministic modeling

NASA Astrophysics Data System (ADS)

De Ridder, K.; Bertrand, C.; Casanova, G.; Lefebvre, W.

2012-09-01

Increasingly, mesoscale meteorological and climate models are used to predict urban weather and climate. Yet, large uncertainties remain regarding values of some urban surface properties. In particular, information concerning urban values for thermal roughness length and thermal admittance is scarce. In this paper, we present a method to estimate values for thermal admittance in combination with an optimal scheme for thermal roughness length, based on METEOSAT-8/SEVIRI thermal infrared imagery in conjunction with a deterministic atmospheric model containing a simple urbanized land surface scheme. Given the spatial resolution of the SEVIRI sensor, the resulting parameter values are applicable at scales of the order of 5 km. As a study case we focused on the city of Paris, for the day of 29 June 2006. Land surface temperature was calculated from SEVIRI thermal radiances using a new split-window algorithm specifically designed to handle urban conditions, as described inAppendix A, including a correction for anisotropy effects. Land surface temperature was also calculated in an ensemble of simulations carried out with the ARPS mesoscale atmospheric model, combining different thermal roughness length parameterizations with a range of thermal admittance values. Particular care was taken to spatially match the simulated land surface temperature with the SEVIRI field of view, using the so-called point spread function of the latter. Using Bayesian inference, the best agreement between simulated and observed land surface temperature was obtained for the Zilitinkevich (1970) and Brutsaert (1975) thermal roughness length parameterizations, the latter with the coefficients obtained by Kanda et al. (2007). The retrieved thermal admittance values associated with either thermal roughness parameterization were, respectively, 1843 ± 108 J m-2 s-1/2 K-1 and 1926 ± 115 J m-2 s-1/2 K-1.

Coupling of WRF and Building-resolved CFD Simulations for Greenhouse Gas Transport and Dispersion

NASA Astrophysics Data System (ADS)

Prasad, K.; Hu, H.; McDermott, R.; Lopez-Coto, I.; Davis, K. J.; Whetstone, J. R.; Lauvaux, T.

2014-12-01

The Indianapolis Flux Experiment (INFLUX) aims to use a top-down inversion methodology to quantify sources of Greenhouse Gas (GHG) emissions over an urban domain with high spatial and temporal resolution. Atmospheric transport of tracer gases from an emission source to a tower mounted receptor are usually conducted using the Weather Research and Forecasting (WRF) model. WRF is used extensively in the atmospheric community to simulate mesoscale atmospheric transport. For such simulations, WRF employs a parameterized turbulence model and does not resolve the fine scale dynamics that are generated by the flow around buildings and communities that are part of a large city. Since the model domain includes the city of Indianapolis, much of the flow of interest is over an urban topography. The NIST Fire Dynamics Simulator (FDS) is a computational fluid dynamics model to perform large eddy simulations of flow around buildings, but it has not been nested within a larger-scale atmospheric transport model such as WRF. FDS has the potential to evaluate the impact of complex urban topography on near-field dispersion and mixing that cannot be simulated with a mesoscale atmospheric model, and which may be important to determining urban GHG emissions using atmospheric measurements. A methodology has been developed to run FDS as a sub-grid scale model within a WRF simulation. The coupling is based on nudging the FDS flow field towards the one computed by WRF, and is currently limited to one way coupling performed in an off-line mode. Using the coupled WRF / FDS model, NIST will investigate the effects of the urban canopy at horizontal resolutions of 2-10 m. The coupled WRF-FDS simulations will be used to calculate the dispersion of tracer gases in an urban domain and to evaluate the upwind areas that contribute to tower observations, referred to in the inversion community as influence functions. Predicted mixing ratios will be compared with tower measurements and WRF simulations, and FDS influence functions will be compared with those generated from WRF and the Lagrangian Particle Dispersion Model. Results of this study will provide guidance regarding the importance of explicit simulations of urban atmospheric turbulence in obtaining accurate estimates of greenhouse gas emissions.

A data-led comparison of simple canopy radiative transfer models for the boreal forest

NASA Astrophysics Data System (ADS)

Reid, T.; Essery, R.; Rutter, N.; King, M.

2012-12-01

Given the computational complexity of numerical weather and climate models, it is worthwhile developing very simple parameterizations for processes such as the transmission of radiation through forest canopies. For this reason, the land surface schemes in global models, and most snow hydrological models, tend to use simple one-dimensional approaches based on Beer's Law or two-stream approximations. Such approaches assume a continuous canopy structure that may not be suitable for the varied, heterogeneous forest cover in boreal regions, especially in winter when snow in the canopy and on the ground may either block radiation or produce multiple reflections between the ground and the trees. There is great benefit in comparing models to real transmissivity values calculated from radiation measurements below and above Arctic canopies. In particular, there is a lack of data for leafless boreal deciduous forests, where canopy gaps are prevalent even at low solar elevation angles near the horizon. In this study, models are compared to radiation data collected in an area of boreal birch forest near Abisko, Sweden in March/April 2011 and mixed conifer forest at Sodankylä, Finland in March/April 2012. Arrays comprising ten shortwave pyranometers were deployed for periods of up to 50 days, under forest plots of varying canopy structures and densities. In addition, global and diffuse shortwave irradiances were recorded at nearby open sites representing the top-of-canopy conditions. A model is developed that explicitly accounts for both diffuse radiation and direct beam transmission on a 5-minute timestep, by using upward-looking hemispherical photographs taken from every pyranometer site. This model reproduces measured transmissivity, although with a slight underestimation, especially at low solar elevations - this could be attributed to multiple reflections that are not accounted for in the model. On the other hand, models based on Beer's Law tend to underestimate the canopy transmissivity significantly, especially for leafless birch canopies where the required assumption of a continuous canopy breaks down. These findings are important for the often sparse, heterogeneous forest cover in boreal regions, where forest edges and canopy gaps are plentiful. They could also have an impact on estimations of overall land surface albedo. Moreover, all models are sensitive to the partitioning of top-of-canopy radiation into its direct and diffuse components, which is complicated by the low solar elevations in the Arctic. More research is required to decide the best way of quantifying the diffuse fraction, using data alongside both physical and empirical models.

Characterization and Low-Dimensional Modeling of Urban Fluid Flow

DTIC Science & Technology

2014-10-06

4 2 Wind Tunnel , Apparatus and Data Processing 7 2.1 Modelling of the Atmospheric Boundary Layer...was demonstrated. Most notably, wind tunnel experiments were performed at a number of different angles of incidence, providing for the first time a...Coceal and Belcher [2004] developed an urban canopy model for mean winds in urban areas that compares well with data from wind tunnel experiments

A new approach to quantify and map carbon stored, sequestered and emissions avoided by urban forests

Treesearch

E. Gregory McPherson; Qingfu Xiao; Elena Aguaron

2013-01-01

This paper describes the use of field surveys, biometric information for urban tree species and remote sensing to quantify and map carbon (C) storage, sequestration and avoided emissions from energy savings. Its primary contribution is methodological; the derivation and application of urban tree canopy (UTC) based transfer functions (t C ha-1 UTC). Findings for Los...

Focusing on the big picture: urban vegetation and eco-hydrological services in U.S. cities (abstract)

EPA Science Inventory

Trees and vegetation can be key components of urban green infrastructure and green spaces such as parks and residential yards. Large trees, characterized by broad canopies, and high leaf and stem volumes, can intercept a substantial amount of stormwater while promoting evapotrans...

America's Urban Forests: Keeping Our Cities Cool

NASA Technical Reports Server (NTRS)

Luvall, Jeffrey C.; Quattrochi, Dale A.

1997-01-01

The additional heating of the air over the city is the result of the replacement of naturally vegetated surfaces with those composed of asphalt, concrete, rooftops and other man-made materials. The temperatures of these artificial surfaces can be 20 to 40 C higher than vegetated surfaces. Materials such as asphalt store much of the sun's energy and remains hot long after sunset. This produces a dome of elevated air temperatures 5 to 8 C greater over the city, compared to the air temperatures over adjacent rural areas. This effect is called the "urban heat island". Tree canopies can reduce the urban heat island effect by dissipating the solar energy received by transpiring water from leaf surfaces which cools the air by taking "heat" from the air to evaporate the water and by shading surfaces like asphalt, roofs, and concrete parking lots which prevents initial heating and storage of heat. It is difficult to take enough temperature measurements over a large city area to characterize the surface temperature variability and quantify the temperature reduction effects of tree canopies. However, the use of remotely sensed thermal data from airborne scanners are ideal for the task. In a study funded by NASA, a series of flights over Huntsville AL were performed in September 1994 and over Atlanta in May 1997. In this article we will examine the techniques of analyzing remotely sensed data for measuring the effect of tree canopies in reducing the urban heat island effect.

Mapping carbon storage in urban trees with multi-source remote sensing data: relationships between biomass, land use, and demographics in Boston neighborhoods.

PubMed

Raciti, Steve M; Hutyra, Lucy R; Newell, Jared D

2014-12-01

High resolution maps of urban vegetation and biomass are powerful tools for policy-makers and community groups seeking to reduce rates of urban runoff, moderate urban heat island effects, and mitigate the effects of greenhouse gas emissions. We developed a very high resolution map of urban tree biomass, assessed the scale sensitivities in biomass estimation, compared our results with lower resolution estimates, and explored the demographic relationships in biomass distribution across the City of Boston. We integrated remote sensing data (including LiDAR-based tree height estimates) and field-based observations to map canopy cover and aboveground tree carbon storage at ~1m spatial scale. Mean tree canopy cover was estimated to be 25.5±1.5% and carbon storage was 355Gg (28.8MgCha(-1)) for the City of Boston. Tree biomass was highest in forest patches (110.7MgCha(-1)), but residential (32.8MgCha(-1)) and developed open (23.5MgCha(-1)) land uses also contained relatively high carbon stocks. In contrast with previous studies, we did not find significant correlations between tree biomass and the demographic characteristics of Boston neighborhoods, including income, education, race, or population density. The proportion of households that rent was negatively correlated with urban tree biomass (R(2)=0.26, p=0.04) and correlated with Priority Planting Index values (R(2)=0.55, p=0.001), potentially reflecting differences in land management among rented and owner-occupied residential properties. We compared our very high resolution biomass map to lower resolution biomass products from other sources and found that those products consistently underestimated biomass within urban areas. This underestimation became more severe as spatial resolution decreased. This research demonstrates that 1) urban areas contain considerable tree carbon stocks; 2) canopy cover and biomass may not be related to the demographic characteristics of Boston neighborhoods; and 3) that recent advances in high resolution remote sensing have the potential to improve the characterization and management of urban vegetation. Copyright © 2014 Elsevier B.V. All rights reserved.

Extreme heat event projections for a coastal megacity

NASA Astrophysics Data System (ADS)

Ortiz, L. E.; Gonzalez, J.

2017-12-01

As summers become warmer, extreme heat events are expected to increase in intensity, frequency, and duration. Large urban centers may affect these projections by introducing feedbacks between the atmosphere and the built environment through processes involving anthropogenic heat, wind modification, radiation blocking, and others. General circulation models are often run with spatial resolutions in the order of 100 km, limiting their skill at resolving local scale processes and highly spatially varying features such as cities' heterogeneous landscape and mountain topography. This study employs climate simulations using the Weather Research and Forecast (WRF) model coupled with a modified multi-layer urban canopy and building energy model to downscale CESM1 at 1 km horizontal resolution across three time slices (2006-2010, 2075-2079, and 2095-2099) and two projections (RCP 4.5 and 8.5). New York City Metropolitan area, with a population of over 20 million and a complex urban canopy, is used as a case study. The urban canopy model of WRF was modified to include a drag coefficient as a function of the building plant area fraction and the introduction of evaporative cooling systems at building roofs to reject the anthropogenic heat from the buildings, with urban canopy parameters computed from the New York City Property Land-Use Tax-lot Output (PLUTO). Model performance is evaluated against the input model and historical records from airport stations, showing improvement in the statistical characteristics in the downscaled model output. Projection results are presented as spatially distributed anomalies in heat wave frequency, duration, and maximum intensity from the 2006-2010 benchmark period. Results show that local sea-breeze circulations mitigate heat wave impacts, following a positive gradient with increasing distance from the coastline. However, end of century RCP 8.5 projections show the possibility of reversal of this pattern, sea surface temperatures increase and reduce the sea-land temperature gradient, thus reducing the sea-breeze magnitude. Impacts to human health and buildings energy demand are explored for future climate scenarios as key examples of anticipated societal consequences.

Stable Stratification Effects on Flow and Pollutant Dispersion in Boundary Layers Entering a Generic Urban Environment

NASA Astrophysics Data System (ADS)

Tomas, J. M.; Pourquie, M. J. B. M.; Jonker, H. J. J.

2016-05-01

Large-eddy simulations (LES) are used to investigate the effect of stable stratification on rural-to-urban roughness transitions. Smooth-wall turbulent boundary layers are subjected to a generic urban roughness consisting of cubes in an in-line arrangement. Two line sources of pollutant are added to investigate the effect on pollutant dispersion. Firstly, the LES method is validated with data from wind-tunnel experiments on fully-developed flow over cubical roughness. Good agreement is found for the vertical profiles of the mean streamwise velocity component and mean Reynolds stress. Subsequently, roughness transition simulations are done for both neutral and stable conditions. Results are compared with fully-developed simulations with conventional double-periodic boundary conditions. In stable conditions, at the end of the domain the streamwise velocity component has not yet reached the fully-developed state even though the surface forces are nearly constant. Moreover, the internal boundary layer is shallower than in the neutral case. Furthermore, an investigation of the turbulence kinetic energy budget shows that the buoyancy destruction term is reduced in the internal boundary layer, above which it is equal to the undisturbed (smooth wall) value. In addition, in stable conditions pollutants emitted above the urban canopy enter the canopy farther downstream due to decreased vertical mixing. Pollutants emitted below the top of the urban canopy are 85 % higher in concentration in stable conditions mostly due to decreased advection. If this is taken into account concentrations remain 17 % greater in stable conditions due to less rapid internal boundary-layer growth. Finally, it is concluded that in the first seven streets the vertical advective pollutant flux is significant, in contrast to the fully-developed case.

Pollutant Dispersion in Boundary Layers Exposed to Rural-to-Urban Transitions: Varying the Spanwise Length Scale of the Roughness

NASA Astrophysics Data System (ADS)

Tomas, J. M.; Eisma, H. E.; Pourquie, M. J. B. M.; Elsinga, G. E.; Jonker, H. J. J.; Westerweel, J.

2017-05-01

Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic particle image velocimetry and laser-induced fluorescence, have been used to investigate pollutant dispersion mechanisms in regions where the surface changes from rural to urban roughness. The urban roughness was characterized by an array of rectangular obstacles in an in-line arrangement. The streamwise length scale of the roughness was kept constant, while the spanwise length scale was varied by varying the obstacle aspect ratio l / h between 1 and 8, where l is the spanwise dimension of the obstacles and h is the height of the obstacles. Additionally, the case of two-dimensional roughness (riblets) was considered in LES. A smooth-wall turbulent boundary layer of depth 10 h was used as the approaching flow, and a line source of passive tracer was placed 2 h upstream of the urban canopy. The experimental and numerical results show good agreement, while minor discrepancies are readily explained. It is found that for l/h=2 the drag induced by the urban canopy is largest of all considered cases, and is caused by a large-scale secondary flow. In addition, due to the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identified that is responsible for street-canyon ventilation for the sixth street and onwards. Moreover, it is shown that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the canopy, while the streamwise length scale does not show a similar trend.

Calibrating the simple biosphere model for Amazonian tropical forest using field and remote sensing data. I - Average calibration with field data

NASA Technical Reports Server (NTRS)

Sellers, Piers J.; Shuttleworth, W. James; Dorman, Jeff L.; Dalcher, Amnon; Roberts, John M.

1989-01-01

Using meteorological and hydrological measurements taken in and above the central-Amazon-basin tropical forest, calibration of the Sellers et al. (1986) simple biosphere (SiB) model are described. The SiB model is a one-dimensional soil-vegetation-atmosphere model designed for use within GCMs models, representing the vegetation cover by analogy with processes operating within a single representative plant. The experimental systems and the procedures used to obtain field data are described, together with the specification of the physiological parameterization required to provide an average description of data. It was found that some of the existing literature on stomatal behavior for tropical species is inconsistent with the observed behavior of the complete canopy in Amazonia, and that the rainfall interception store of the canopy is considerably smaller than originally specified in the SiB model.

Physics of Canopy Boundary Layer Resistance for Better Quantification of Sensitivity of Deforestation Scenarios

NASA Astrophysics Data System (ADS)

Ragi, K. B.; Patel, R.

2015-12-01

A great deal of studies focused on deforestation scenarios in the tropical rainforests. Though all these efforts are useful in the understanding of its response to climate, the systematic understanding of uncertainties in representation of physical processes related to vegetation through sensitivity studies is imperative antecedently to understand the real role of vegetation in changing the climate. It is understood that the dense vegetation fluxes energy and moisture to the atmosphere. But, how much a specific process/a group of processes in the surface conditions of a specific area helps flux energy, moisture and tracers is unknown due to lack of process sensitivity studies and uncertain due to malfunctioning of processes. In this presentation, we have found a faulty parameterization, through process sensitivity studies, that would abet in energy and moisture fluxes to the atmosphere. The model we have employed is the Common Land Model2014. The area we have chosen is the Congolese rainforest. We have discovered the flaw in the leaf boundary layer resistance (LBLR), through sensitivity studies in the LSMs, especially in the dense forest regions. This LBLR is over-parameterized with constant heat transfer coefficient and characteristic dimension of leaves; and friction velocity. However, it is too scant because of overlooking of significant complex physics of turbulence and canopy roughness boundary layer to function it realistically. Our sensitivity results show the deficiency of this process and we have formulated canopy boundary layer resistance, instead of LBLR, with depending variables such as LAI, roughness length, vegetation temperature using appropriate thermo-fluid dynamical principles. We are running the sensitivity experiments with new formulations for setting the parameter values for the data not available so far. This effort would lead to better physics for the land-use change studies and demand for the retrieval of new parameters from satellite/field experiments such as leaf mass per area and specific heat capacity of vegetation.

Influence of Land Cover Heterogeneity, Land-Use Change and Management on the Regional Carbon Cycle in the Upper Midwest USA as Evaluated by High-Density Observations and a Dynamic Ecosystem Model

NASA Astrophysics Data System (ADS)

Desai, A. R.; Bolstad, P. V.; Moorcroft, P. R.; Davis, K. J.

2005-12-01

The interplay between land use change, forest management and land cover variability complicates the ability to characterize regional scale (10-1000 km) exchange of carbon dioxide between the land surface and atmosphere in heterogeneous landscapes. An attempt was made to observe and model these factors and their influence on the regional carbon cycle across the upper Midwest USA. A high density of eddy-covariance carbon flux, micrometeorology, carbon dioxide mixing ratio, stand-scale biometry and canopy component flux observations have been occurring in this area as part of the Chequamegon Ecosystem-Atmosphere Study. Observations limited to sampling only dominant stands and coarse-resolution biogeochemical models limited to biome-scale parameterization neither accurately capture the variability of carbon fluxes measured by the network of eddy covariance towers nor match the regional-scale carbon flux inferred from very tall tower eddy covariance measurements and multi-site upscaling. Analysis of plot level biometric data, U.S. Forest Service Forest Inventory Analysis data and high-resolution land cover data around the tall tower revealed significant variations in vegetation type, stand age, canopy stocking and structure. Wetlands, clearcuts and recent natural disturbances occur in characteristic small non-uniformly distributed patches that aggregate to form more than 30% of the landscape. The Ecosystem Demography model, a dynamic ecosystem model that incorporates vegetation heterogeneity, canopy structure, stand age, disturbance, land use change and forest management, was parameterized with regional biometric data and meteorology, historical records of land management and high-resolution satellite land cover maps. The model will be used to examine the significance of past land use change, natural disturbance history and current forest management in explaining landscape structure and regional carbon fluxes observed in the region today.

Retrieving Biome Types from Multi-angle Spectral Data

NASA Astrophysics Data System (ADS)

Schull, M. A.; Xu, L.; Latorre, P.; Samanta, A.; Myneni, R. B.; Knyazikhin, Y.

2009-12-01

Many studies have been conducted to demonstrate the ability of multi-angle spectral data to discriminate plant dominant species. Most have employed the use of empirically based techniques, which are site specific, requires some initial training based on characteristics of known leaf and/or canopy spectra and therefore may not be extendable to operational use or adapted to changing/unknown land cover. An ancillary objective of the MISR LAI/FPAR algorithm is classification of global vegetation into biome types. The algorithm is based on the 3D radiative transfer equation. Its performance suggests that is has valid LAI retrievals and correct biome identification in about 20% of the pixels. However with a probability of about 70%, uncertainties in LAI retrievals due to biome misclassification do not exceed uncertainties in the observations. In this poster we present an approach to improve reliability of the distribution of biomes and dominant species from multi angle spectral data. The radiative transfer theory of canopy spectral invariants underlies the approach, which facilitates parameterization of the canopy bidirectional reflectance factor in terms of the leaf spectrum and two spectrally invariant and structurally varying variables - recollision and directional escape probabilities. Theoretical and empirical analyses of ground and airborne data acquired by AVIRIS, AirMISR over two sites in New England and CHRIS/PROBA over BARAX site in Spain suggest that the canopy spectral invariants convey information about canopy structure at both the macro and micro scales. These properties allow for the natural separation of biome classes based on the location of points on the total escape probability vs the proportional escape ratio log-log plane.

Thermal signatures of urban land cover types: High-resolution thermal infrared remote sensing of urban heat island in Huntsville, AL

NASA Technical Reports Server (NTRS)

Lo, Chor Pang

1996-01-01

The main objective of this research is to apply airborne high-resolution thermal infrared imagery for urban heat island studies, using Huntsville, AL, a medium-sized American city, as the study area. The occurrence of urban heat islands represents human-induced urban/rural contrast, which is caused by deforestation and the replacement of the land surface by non-evaporating and non-porous materials such as asphalt and concrete. The result is reduced evapotranspiration and more rapid runoff of rain water. The urban landscape forms a canopy acting as a transitional zone between the atmosphere and the land surface. The composition and structure of this canopy have a significant impact on the thermal behavior of the urban environment. Research on the trends of surface temperature at rapidly growing urban sites in the United States during the last 30 to 50 years suggests that significant urban heat island effects have caused the temperatures at these sites to rise by 1 to 2 C. Urban heat islands have caused changes in urban precipitation and temperature that are at least similar to, if not greater than, those predicted to develop over the next 100 years by global change models. Satellite remote sensing, particularly NOAA AVHRR thermal data, has been used in the study of urban heat islands. Because of the low spatial resolution (1.1 km at nadir) of the AVHRR data, these studies can only examine and map the phenomenon at the macro-level. The present research provides the rare opportunity to utilize 5-meter thermal infrared data acquired from an airplane to characterize more accurately the thermal responses of different land cover types in the urban landscape as input to urban heat island studies.

Assessing urban forest effects and values, Minneapolis' urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Minneapolis, MN, reveals that the city has about 979,000 trees with canopies that cover 26.4 percent of the area. The most common tree species are green ash, American elm, and boxelder. The urban forest currently stores about 250,000 tons of carbon valued at $4.6 million. In addition, these trees remove about 8,900 tons of carbon per year ($164,...

Assessing urban forest effects and values, Casper's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Casper, WY reveals that this city has about 123,000 trees with canopies that cover 8.9 percent of the area. The most common tree species are plains cottonwood, blue spruce, and American elm. The urban forest currently store about 37,000 tons of carbon valued at $689,000. In addition, these trees remove about 1,200 tons of carbon per year ($22,...

Assessing urban forest effects and values: Toronto's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Allison R. Bodine; Eric J. Greenfield; Alexis Ellis; Theodore A. Endreny; Yang Yang; Tian Zhou; Ruthanne Henry

2013-01-01

An analysis of trees in Toronto, Ontario, reveals that this city has about 10.2 million trees with a tree and shrub canopy that covers approximately 26.6 percent of the city. The most common tree species are eastern white-cedar, sugar maple, and Norway maple. The urban forest currently stores an estimated 1.1 million metric tons of carbon valued at CAD$25.0 million. In...

Assessing urban forest effects and values, Philladelphia's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in Philadelphia reveals that this city has about 2.1 million trees with canopies that cover 15.7 percent of the area. The most common tree species are black cherry, crabapple, and tree of heaven. The urban forest currently stores about 530,000 tons of carbon valued at $9.8 million. In addition, these trees remove about 16,100 tons of carbon per...

Assessing urban forest effects and values, San Francisco's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in San Francisco, CA reveals that this city has about 669,000 trees with canopies that cover 11.9 percent of the area. The most common tree species are blue gum eucalyptus, Monterey pine, and Monterey cypress. The urban forest currently stores about 196,000 tons of carbon valued at $3.6 million. In addition, these trees remove about 5,200 tons of...

Application and evaluation of high-resolution WRF-CMAQ with simple urban parameterization.

EPA Science Inventory

The 2-way coupled WRF-CMAQ meteorology and air quality modeling system is evaluated for high-resolution applications by comparing to a regional air quality field study (Discover-AQ). The model was modified to better account for the effects of urban environments. High-resolution...

Application and evaluation of high-resolution WRF-CMAQ with simple urban parameterization

EPA Science Inventory

The 2-way coupled WRF-CMAQ meteorology and air quality modeling system is evaluated for high-resolution applications by comparing to a regional air quality field study (Discover-AQ). The model was modified to better account for the effects of urban environments. High-resolution...

Ten-year performance of the United States national elm trial

Treesearch

Jason J. Griffin; William R. Jacobi; E. Gregory McPherson; Clifford S. Sadof; James R. McKenna; Mark L. Gleason; Nicole Ward Gauthier; Daniel A. Potter; David R. Smitley; Gerard C. Adams; Ann Brooks Gould; Christian R. Cash; James A. Walla; Mark C. Starrett; Gary Chastagner; Jeff L. Sibley; Vera A. Krischik; Adam F. Newby

2017-01-01

Ulmus americana (American elm) was an important urban tree in North America prior to the introduction of the Dutch elm disease pathogen in 1930. Subsequently, urban and community forests were devastated by the loss of large canopies. Tree improvement programs produced disease tolerant American and Eurasian elm cultivars and introduced them into the...

Multi-scale comparison of the fine particle removal capacity of urban forests and wetlands.

PubMed

Zhang, Zhenming; Liu, Jiakai; Wu, Yanan; Yan, Guoxin; Zhu, Lijuan; Yu, Xinxiao

2017-04-10

As fine particle (FP) pollution is harmful to humans, previous studies have focused on the mechanisms of FP removal by forests. The current study aims to compare the FP removal capacities of urban forests and wetlands on the leaf, canopy, and landscape scales. Water washing and scanning electron microscopy are used to calculate particle accumulation on leaves, and models are used to estimate vegetation collection, sedimentation, and dry deposition. Results showed that, on the leaf scale, forest species are able to accumulate more FP on their leaf surface than aquatic species in wetlands. On the canopy scale, horizontal vegetation collection is the major process involved in FP removal, and the contribution of vertical sedimentation/emission can be ignored. Coniferous tree species also showed stronger FP collection ability than broadleaf species. In the landscape scale, deposition on the forest occurs to a greater extent than that on wetlands, and dry deposition is the major process of FP removal on rain-free days. In conclusion, when planning an urban green system, planting an urban forest should be the first option for FP mitigation.

Physically-based parameterization of spatially variable soil and vegetation using satellite multispectral data

NASA Technical Reports Server (NTRS)

Jasinski, Michael F.; Eagleson, Peter S.

1989-01-01

A stochastic-geometric landsurface reflectance model is formulated and tested for the parameterization of spatially variable vegetation and soil at subpixel scales using satellite multispectral images without ground truth. Landscapes are conceptualized as 3-D Lambertian reflecting surfaces consisting of plant canopies, represented by solid geometric figures, superposed on a flat soil background. A computer simulation program is developed to investigate image characteristics at various spatial aggregations representative of satellite observational scales, or pixels. The evolution of the shape and structure of the red-infrared space, or scattergram, of typical semivegetated scenes is investigated by sequentially introducing model variables into the simulation. The analytical moments of the total pixel reflectance, including the mean, variance, spatial covariance, and cross-spectral covariance, are derived in terms of the moments of the individual fractional cover and reflectance components. The moments are applied to the solution of the inverse problem: The estimation of subpixel landscape properties on a pixel-by-pixel basis, given only one multispectral image and limited assumptions on the structure of the landscape. The landsurface reflectance model and inversion technique are tested using actual aerial radiometric data collected over regularly spaced pecan trees, and using both aerial and LANDSAT Thematic Mapper data obtained over discontinuous, randomly spaced conifer canopies in a natural forested watershed. Different amounts of solar backscattered diffuse radiation are assumed and the sensitivity of the estimated landsurface parameters to those amounts is examined.

The implementation of biofiltration systems, rainwater tanks and urban irrigation in a single-layer urban canopy model

NASA Astrophysics Data System (ADS)

Demuzere, Matthias; Coutts, Andrew; Goehler, Maren; Broadbent, Ashley; Wouters, Hendrik; van Lipzig, Nicole; Gebert, Luke

2015-04-01

Urban vegetation is generally considered as a key tool to modify the urban energy balance through enhanced evapotranspiration (ET). Given that vegetation is most effective when it is healthy, stormwater harvesting and retention strategies (such as water sensitive urban design) could be used to support vegetation and promote ET. This study presents the implementation of a vegetated lined bio-filtration system (BFS) combined with a rainwater tank (RWT) and urban irrigation system in the single-layer urban canopy model Community Land Model-Urban. Runoff from roof and impervious road surface fractions is harvested and used to support an adequate soil moisture level for vegetation in the BFS. In a first stage, modelled soil moisture dynamics are evaluated and found reliable compared to observed soil moisture levels from biofiltration pits in Smith Street, Melbourne (Australia). Secondly, the impact of BFS, RWT and urban irrigation on ET is illustrated for a two-month period in 2012 using varying characteristics for all components. Results indicate that (i) a large amount of stormwater is potentially available for indoor and outdoor water demands, including irrigation of urban vegetation, (ii) ET from the BFS is an order of magnitude larger compared to the contributions from the impervious surfaces, even though the former only covers 10% of the surface fraction and (iii) attention should be paid to the cover fraction and soil texture of the BFS, size of the RWT and the surface fractions contributing to the collection of water in the RWT. Overall, this study reveals that this model development can effectuate future research with state-of-the-art urban climate models to further explore the benefits of vegetated biofiltration systems as a water sensitive urban design tool optimised with an urban irrigation system to maintain healthy vegetation.

Non-chemistry coupled PM10 modeling in Chiang Mai City, Northern Thailand: A fast operational approach for aerosol forecasts

NASA Astrophysics Data System (ADS)

Macatangay, Ronald; Bagtasa, Gerry; Sonkaew, Thiranan

2017-09-01

The Weather Research and Forecasting (WRF v. 3.7) model was applied to model PM10 data in Chiang Mai city for 10-days during a high haze event utilizing updated land use categories from the Moderate Resolution Imaging Spectroradiometer (MODIS). A higher resolution meteorological lateral boundary condition (from 1 degree to 0.25 degree) was also used from the NCEP GDAS/FNL Global Tropospheric Analyses and Forecast Grid system. A 3-category urban canopy model was also added and the Thompson aerosol-aware microphysics parameterization scheme was used to model the aerosol number concentrations that were later converted to PM10 concentrations. Aerosol number concentration monthly climatology was firstly used as initial and lateral boundary conditions to model PM10 concentrations. These were compared to surface data obtained from two stations of the Pollution Control Department (PCD) of Thailand. The results from the modeled PM10 concentrations could not capture the variability (r = 0.29; 0.27 for each site) and underestimated a high PM10 spike during the period studied. The authors then added satellite data to the aerosol climatology that improved the comparison with observations (r = 0.45; 43). However, both model runs still were not able to capture the high PM10 concentration event. This requires further investigation.

Demonstrating the Uneven Importance of Fine-Scale Forest Structure on Snow Distributions using High Resolution Modeling

NASA Astrophysics Data System (ADS)

Broxton, P. D.; Harpold, A. A.; van Leeuwen, W.; Biederman, J. A.

2016-12-01

Quantifying the amount of snow in forested mountainous environments, as well as how it may change due to warming and forest disturbance, is critical given its importance for water supply and ecosystem health. Forest canopies affect snow accumulation and ablation in ways that are difficult to observe and model. Furthermore, fine-scale forest structure can accentuate or diminish the effects of forest-snow interactions. Despite decades of research demonstrating the importance of fine-scale forest structure (e.g. canopy edges and gaps) on snow, we still lack a comprehensive understanding of where and when forest structure has the largest impact on snowpack mass and energy budgets. Here, we use a hyper-resolution (1 meter spatial resolution) mass and energy balance snow model called the Snow Physics and Laser Mapping (SnowPALM) model along with LIDAR-derived forest structure to determine where spatial variability of fine-scale forest structure has the largest influence on large scale mass and energy budgets. SnowPALM was set up and calibrated at sites representing diverse climates in New Mexico, Arizona, and California. Then, we compared simulations at different model resolutions (i.e. 1, 10, and 100 m) to elucidate the effects of including versus not including information about fine scale canopy structure. These experiments were repeated for different prescribed topographies (i.e. flat, 30% slope north, and south-facing) at each site. Higher resolution simulations had more snow at lower canopy cover, with the opposite being true at high canopy cover. Furthermore, there is considerable scatter, indicating that different canopy arrangements can lead to different amounts of snow, even when the overall canopy coverage is the same. This modeling is contributing to the development of a high resolution machine learning algorithm called the Snow Water Artificial Network (SWANN) model to generate predictions of snow distributions over much larger domains, which has implications for improving land surface models that do not currently resolve or parameterize fine-scale canopy structure. In addition, these findings have implications for understanding the potential of different forest management strategies (i.e. thinning) based on local topography and climate to maximize the amount and retention of snow.

Strategic guidelines for street canyon geometry to achieve sustainable street air quality—part II: multiple canopies and canyons

NASA Astrophysics Data System (ADS)

Chan, Andy T.; Au, William T. W.; So, Ellen S. P.

The flow field and pollutant dispersion characteristics in a three-dimensional urban street canyon are investigated for various building array geometries. The street canyon in consideration is located in a multi-canopy building array that is similar to realistic estate situations. The pollutant dispersion characteristics are studied for various canopy aspect ratios, namely: the canyon height to width ratio, canyon length to height ratio, canyon breadth ratio and crossroad locations are studied. A three-dimensional field-size canyon has been analysed through numerical simulations using k- ɛ turbulence model. As expected, the wind flow and mode of pollutant dispersion is strongly dependent on the various flow geometric configurations and that the results can be different from that of a single canyon system. For example, it is found that the pollutant retention value is minimum when the canyon height-to-width ratio is approximately 0.8, or that the building height ratio is 0.5. Various rules of thumbs on urban canyon geometry have been established for good pollutant dispersion.

The influence of the surface roughness parameterization on remote sensing-based estimates of evapotranspiration from vineyards

NASA Astrophysics Data System (ADS)

Alfieri, J. G.; Kustas, W. P.; Gao, F.; Nieto, H.; Prueger, J. H.; Hipps, L.

2017-12-01

Because the judicious application of water is key to ensuring berry quality, information regarding evapotranspiration (ET) is critical when making irrigation and other crop management decisions for vineyards. Increasingly, wine grape producers seek to use remote sensing-based models to monitor ET and inform management decisions. However, the parameterization schemes used by these models do not fully account for the effects of the highly-structured canopy architecture on either the roughness characteristics of the vineyard or the turbulent transport and exchange within and above the vines. To investigate the effects of vineyard structure on the roughness length (zo) and displacement height (do) of vineyards, data collected from 2013 to 2016 as a part of the Grape Remote Sensing Atmospheric Profiling and Evapotranspiration Experiment (GRAPEX), an ongoing multi-agency field campaign conducted in the Central Valley of California, was used. Specifically, vertical profiles (2.5 m, 3.75 m, 5 m, and 8 m, agl) of wind velocity collected under near-neutral conditions were used to estimate do and zo and characterize how these roughness parameters vary in response changing environmental conditions. The roughness length was found to vary as a function of wind direction. It increased sigmoidally from a minimum near 0.15 m when the wind direction was parallel to the vine rows to a maximum between 0.3 m and 0.4 m when the winds were perpendicularly to the rows. Similarly, do was found responds strongly to changes in vegetation density as measured via leaf area index (LAI). Although the maximum varied from year-to-year, do increased rapidly after bud break in all cases and then remained constant for the remainder of the growing season. A comparison of the model output from the remote sensing-based two-source energy balance (TSEB) model using the standard roughness parameterization scheme and the empirical relationships derived from observations indicates a that the modeled ET estimates decrease by 10% to 40%. These results not only demonstrate the unique effects of highly-structured canopies on aerodynamic characteristics, they also provide well-behaved relationships that may be used to improve the accuracy of the model parameterization of do and zo, thus the turbulent fluxes including ET, within vineyards.

Assessing urban forest effects and values, Washington, D.C.'s urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Washington, D.C. reveals that this city has about 1,928,000 trees with canopies that cover 28.6 percent of the area. The most common tree species are American beech, red maple, and boxelder. The urban forest currently store about 526,000 tons of carbon valued at $9.7 million. In addition, these trees remove about 16,200 tons of carbon per year...

Assessing urban forest effects and values, New York City's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in New York City reveals that this city has about 5.2 million trees with canopies that cover 20.9 percent of the area. The most common tree species are tree of heaven, black cherry, and sweetgum. The urban forest currently stores about 1.35 million tons of carbon valued at $24.9 million. In addition, these trees remove about 42,300 tons of carbon...

Estimating the relationship between urban 3D morphology and land surface temperature using airborne LiDAR and Landsat-8 Thermal Infrared Sensor data

NASA Astrophysics Data System (ADS)

Lee, J. H.

2015-12-01

Urban forests are known for mitigating the urban heat island effect and heat-related health issues by reducing air and surface temperature. Beyond the amount of the canopy area, however, little is known what kind of spatial patterns and structures of urban forests best contributes to reducing temperatures and mitigating the urban heat effects. Previous studies attempted to find the relationship between the land surface temperature and various indicators of vegetation abundance using remote sensed data but the majority of those studies relied on two dimensional area based metrics, such as tree canopy cover, impervious surface area, and Normalized Differential Vegetation Index, etc. This study investigates the relationship between the three-dimensional spatial structure of urban forests and urban surface temperature focusing on vertical variance. We use a Landsat-8 Thermal Infrared Sensor image (acquired on July 24, 2014) to estimate the land surface temperature of the City of Sacramento, CA. We extract the height and volume of urban features (both vegetation and non-vegetation) using airborne LiDAR (Light Detection and Ranging) and high spatial resolution aerial imagery. Using regression analysis, we apply empirical approach to find the relationship between the land surface temperature and different sets of variables, which describe spatial patterns and structures of various urban features including trees. Our analysis demonstrates that incorporating vertical variance parameters improve the accuracy of the model. The results of the study suggest urban tree planting is an effective and viable solution to mitigate urban heat by increasing the variance of urban surface as well as evaporative cooling effect.

The urban boundary-layer field campaign in marseille (ubl/clu-escompte): set-up and first results

NASA Astrophysics Data System (ADS)

Mestayer, P.G.; Durand, P.; Augustin, P.; Bastin, S.; Bonnefond, J.-M.; Benech, B.; Campistron, B.; Coppalle, A.; Delbarre, H.; Dousset, B.; Drobinski, P.; Druilhet, A.; Frejafon, E.; Grimmond, C.S.B.; Groleau, D.; Irvine, M.; Kergomard, C.; Kermadi, S.; Lagouarde, J.-P.; Lemonsu, A.; Lohou, F.; Long, N.; Masson, V.; Moppert, C.; Noilhan, J.; Offerle, B.; Oke, T.R.; Pigeon, G.; Puygrenier, V.; Roberts, S.; Rosant, J.-M.; Sanid, F.; Salmond, J.; Talbaut, M.; Voogt, J.

The UBL/CLU (urban boundary layer/couche limite urbaine) observation and modelling campaign is a side-project of the regional photochemistry campaign ESCOMPTE. UBL/CLU focuses on the dynamics and thermodynamics of the urban boundary layer of Marseille, on the Mediterranean coast of France. The objective of UBL/CLU is to document the four-dimensional structure of the urban boundary layer and its relation to the heat and moisture exchanges between the urban canopy and the atmosphere during periods of low wind conditions, from June 4 to July 16, 2001. The project took advantage of the comprehensive observational set-up of the ESCOMPTE campaign over the Berre-Marseille area, especially the ground-based remote sensing, airborne measurements, and the intensive documentation of the regional meteorology. Additional instrumentation was installed as part of UBL/CLU. Analysis objectives focus on (i) validation of several energy balance computational schemes such as LUMPS, TEB and SM2-U, (ii) ground truth and urban canopy signatures suitable for the estimation of urban albedos and aerodynamic surface temperatures from satellite data, (iii) high resolution mapping of urban land cover, land-use and aerodynamic parameters used in UBL models, and (iv) testing the ability of high resolution atmospheric models to simulate the structure of the UBL during land and sea breezes, and the related transport and diffusion of pollutants over different districts of the city. This paper presents initial results from such analyses and details of the overall experimental set-up.

Prioritizing preferable locations for increasing urban tree canopy in New York City

Treesearch

Dexter Locke; J. Morgan Grove; Jacqueline W.T. Lu; Austin Troy; Jarlath P.M. O' Neil-Dunne; Brian Beck

2010-01-01

This paper presents a set of Geographic Information System (GIS) methods for identifying and prioritizing tree planting sites in urban environments. It uses an analytical approach created by a University of Vermont service-learning class called "GIS Analysis of New York City's Ecology" that was designed to provide research support to the MillionTreesNYC...

Three-Dimensional Mapping of Air Flow at an Urban Canyon Intersection

NASA Astrophysics Data System (ADS)

Carpentieri, Matteo; Robins, Alan G.; Baldi, Sandro

2009-11-01

In this experimental work both qualitative (flow visualisation) and quantitative (laser Doppler anemometry) methods were applied in a wind tunnel in order to describe the complex three-dimensional flow field in a real environment (a street canyon intersection). The main aim was an examination of the mean flow, turbulence and flow pathlines characterising a complex three-dimensional urban location. The experiments highlighted the complexity of the observed flows, particularly in the upwind region of the intersection. In this complex and realistic situation some details of the upwind flow, such as the presence of two tall towers, play an important role in defining the flow field within the intersection, particularly at roof level. This effect is likely to have a strong influence on the mass exchange mechanism between the canopy flow and the air aloft, and therefore the distribution of pollutants. This strong interaction between the flows inside and outside the urban canopy is currently neglected in most state-of-the-art local scale dispersion models.

Differences in BVOC oxidation and SOA formation above and below the forest canopy

NASA Astrophysics Data System (ADS)

Schulze, Benjamin C.; Wallace, Henry W.; Flynn, James H.; Lefer, Barry L.; Erickson, Matt H.; Jobson, B. Tom; Dusanter, Sebastien; Griffith, Stephen M.; Hansen, Robert F.; Stevens, Philip S.; VanReken, Timothy; Griffin, Robert J.

2017-02-01

Gas-phase biogenic volatile organic compounds (BVOCs) are oxidized in the troposphere to produce secondary pollutants such as ozone (O3), organic nitrates (RONO2), and secondary organic aerosol (SOA). Two coupled zero-dimensional models have been used to investigate differences in oxidation and SOA production from isoprene and α-pinene, especially with respect to the nitrate radical (NO3), above and below a forest canopy in rural Michigan. In both modeled environments (above and below the canopy), NO3 mixing ratios are relatively small (< 0.5 pptv); however, daytime (08:00-20:00 LT) mixing ratios below the canopy are 2 to 3 times larger than those above. As a result of this difference, NO3 contributes 12 % of total daytime α-pinene oxidation below the canopy while only contributing 4 % above. Increasing background pollutant levels to simulate a more polluted suburban or peri-urban forest environment increases the average contribution of NO3 to daytime below-canopy α-pinene oxidation to 32 %. Gas-phase RONO2 produced through NO3 oxidation undergoes net transport upward from the below-canopy environment during the day, and this transport contributes up to 30 % of total NO3-derived RONO2 production above the canopy in the morning (˜ 07:00). Modeled SOA mass loadings above and below the canopy ultimately differ by less than 0.5 µg m-3, and extremely low-volatility organic compounds dominate SOA composition. Lower temperatures below the canopy cause increased partitioning of semi-volatile gas-phase products to the particle phase and up to 35 % larger SOA mass loadings of these products relative to above the canopy in the model. Including transport between above- and below-canopy environments increases above-canopy NO3-derived α-pinene RONO2 SOA mass by as much as 45 %, suggesting that below-canopy chemical processes substantially influence above-canopy SOA mass loadings, especially with regard to monoterpene-derived RONO2.

Seasonal albedo of an urban/rural landscape from satellite observations

NASA Technical Reports Server (NTRS)

Brest, Christopher L.

1987-01-01

Using data from 27 calibrated Landsat observations of the Hartford, Connecticut area, the spatial distribution and seasonal variation of surface reflectance and albedo were examined. Mean values of visible reflectance, near-IR reflectance, and albedo are presented (for both snow-free and snow-cover observations) according to 14 land use/land cover categories. A diversity of albedo values was found to exist in this type of environment, associated with land cover. Many land-cover categories display a seasonal dependence, with intracategory seasonal differences being of comparable magnitude to intercategory differences. Key factors in determining albedo (and its seasonal dynamics) are the presence or absence of vegetation and the canopy structure. Snow-cover/snow-free differences range from a few percent (for urban land covers) to over 40 percent (for low-canopy vegetation).

Estimation of effective aerodynamic roughness with altimeter measurements

NASA Technical Reports Server (NTRS)

Menenti, M.; Ritchie, J. C.

1992-01-01

A new method is presented for estimating the aerodynamic roughness length of heterogeneous land surfaces and complex landscapes using elevation measurements performed with an airborne laser altimeter and the Seasat radar altimeter. Land surface structure is characterized at increasing length scales by considering three basic landscape elements: (1) partial to complete canopies of herbaceous vegetation; (2) sparse obstacles (e.g., shrubs and trees); and (3) local relief. Measured parameters of land surface geometry are combined to obtain an effective aerodynamic roughness length which parameterizes the total atmosphere-land surface stress.

The impact of changing the land surface scheme in ACCESS(v1.0/1.1) on the surface climatology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kowalczyk, Eva A.; Stevens, Lauren E.; Law, Rachel M.

The Community Atmosphere Biosphere Land Exchange (CABLE) model has been coupled to the UK Met Office Unified Model (UM) within the existing framework of the Australian Community Climate and Earth System Simulator (ACCESS), replacing the Met Office Surface Exchange Scheme (MOSES). Here we investigate how features of the CABLE model impact on present-day surface climate using ACCESS atmosphere-only simulations. The main differences attributed to CABLE include a warmer winter and a cooler summer in the Northern Hemisphere (NH), earlier NH spring runoff from snowmelt, and smaller seasonal and diurnal temperature ranges. The cooler NH summer temperatures in canopy-covered regions aremore » more consistent with observations and are attributed to two factors. Firstly, CABLE accounts for aerodynamic and radiative interactions between the canopy and the ground below; this placement of the canopy above the ground eliminates the need for a separate bare ground tile in canopy-covered areas. Secondly, CABLE simulates larger evapotranspiration fluxes and a slightly larger daytime cloud cover fraction. Warmer NH winter temperatures result from the parameterization of cold climate processes in CABLE in snow-covered areas. In particular, prognostic snow density increases through the winter and lowers the diurnally resolved snow albedo; variable snow thermal conductivity prevents early winter heat loss but allows more heat to enter the ground as the snow season progresses; liquid precipitation freezing within the snowpack delays the building of the snowpack in autumn and accelerates snow melting in spring. Altogether we find that the ACCESS simulation of surface air temperature benefits from the specific representation of the turbulent transport within and just above the canopy in the roughness sublayer as well as the more complex snow scheme in CABLE relative to MOSES.« less

The impact of changing the land surface scheme in ACCESS(v1.0/1.1) on the surface climatology

DOE PAGES

Kowalczyk, Eva A.; Stevens, Lauren E.; Law, Rachel M.; ...

2016-08-23

The Community Atmosphere Biosphere Land Exchange (CABLE) model has been coupled to the UK Met Office Unified Model (UM) within the existing framework of the Australian Community Climate and Earth System Simulator (ACCESS), replacing the Met Office Surface Exchange Scheme (MOSES). Here we investigate how features of the CABLE model impact on present-day surface climate using ACCESS atmosphere-only simulations. The main differences attributed to CABLE include a warmer winter and a cooler summer in the Northern Hemisphere (NH), earlier NH spring runoff from snowmelt, and smaller seasonal and diurnal temperature ranges. The cooler NH summer temperatures in canopy-covered regions aremore » more consistent with observations and are attributed to two factors. Firstly, CABLE accounts for aerodynamic and radiative interactions between the canopy and the ground below; this placement of the canopy above the ground eliminates the need for a separate bare ground tile in canopy-covered areas. Secondly, CABLE simulates larger evapotranspiration fluxes and a slightly larger daytime cloud cover fraction. Warmer NH winter temperatures result from the parameterization of cold climate processes in CABLE in snow-covered areas. In particular, prognostic snow density increases through the winter and lowers the diurnally resolved snow albedo; variable snow thermal conductivity prevents early winter heat loss but allows more heat to enter the ground as the snow season progresses; liquid precipitation freezing within the snowpack delays the building of the snowpack in autumn and accelerates snow melting in spring. Altogether we find that the ACCESS simulation of surface air temperature benefits from the specific representation of the turbulent transport within and just above the canopy in the roughness sublayer as well as the more complex snow scheme in CABLE relative to MOSES.« less

Validation of the Martilli's Urban Boundary Layer Scheme with measurements from two mid-latitude European cities

NASA Astrophysics Data System (ADS)

Hamdi, R.; Schayes, G.

2005-07-01

The Martilli's urban parameterization scheme is improved and implemented in a mesoscale model in order to take into account the typical effects of a real city on the air temperature near the ground and on the surface exchange fluxes. The mesoscale model is run on a single column using atmospheric data and radiation recorded above roof level as forcing. Here, the authors validate the Martilli's urban boundary layer scheme using measurements from two mid-latitude European cities: Basel, Switzerland and Marseilles, France. For Basel, the model performance is evaluated with observations of canyon temperature, surface radiation, and energy balance fluxes obtained during the Basel urban boundary layer experiment (BUBBLE). The results show that the urban parameterization scheme is able to reproduce the generation of the Urban Heat Island (UHI) effect over urban area and represents correctly most of the behavior of the fluxes typical of the city center of Basel, including the large heat uptake by the urban fabric and the positive sensible heat flux at night. For Marseilles, the model performance is evaluated with observations of surface temperature, canyon temperature, surface radiation, and energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) and its urban boundary layer (UBL) campaign. At both urban sites, vegetation cover is less than 20%, therefore, particular attention was directed to the ability of the Martilli's urban boundary layer scheme to reproduce the observations for the Marseilles city center, where the urban parameters and the synoptic forcing are totally different from Basel. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model correctly simulates the net radiation, canyon temperature, and the partitioning between the turbulent and storage heat fluxes.

Exotic weeds and fluctuating microclimate can constrain native plant regeneration in urban forest restoration.

PubMed

Wallace, K J; Laughlin, Daniel C; Clarkson, Bruce D

2017-06-01

Restoring forest structure and composition is an important component of urban land management, but we lack clear understanding of the mechanisms driving restoration success. Here we studied two indicators of restoration success in temperate rainforests: native tree regeneration and epiphyte colonization. We hypothesized that ecosystem properties such as forest canopy openness, abundance of exotic herbaceous weeds, and the microclimate directly affect the density and diversity of native tree seedlings and epiphytes. Relationships between environmental conditions and the plant community were investigated in 27 restored urban forests spanning 3-70 years in age and in unrestored and remnant urban forests. We used structural equation modelling to determine the direct and indirect drivers of native tree regeneration and epiphyte colonization in the restored forests. Compared to remnant forest, unrestored forest had fewer native canopy tree species, significantly more light reaching the forest floor annually, and higher exotic weed cover. Additionally, epiphyte density was lower and native tree regeneration density was marginally lower in the unrestored forests. In restored forests, light availability was reduced to levels found in remnant forests within 20 years of restoration planting, followed shortly thereafter by declines in herbaceous exotic weeds and reduced fluctuation of relative humidity and soil temperatures. Contrary to expectations, canopy openness was only an indirect driver of tree regeneration and epiphyte colonization, but it directly regulated weed cover and microclimatic fluctuations, both of which directly drove the density and richness of regeneration and epiphyte colonization. Epiphyte density and diversity were also positively related to forest basal area, as large trees provide physical habitat for colonization. These results imply that ecosystem properties change predictably after initial restoration plantings, and that reaching critical thresholds in some ecosystem properties makes conditions suitable for the regeneration of late successional species, which is vital for restoration success and long-term ecosystem sustainability. Abiotic and biotic conditions that promote tree regeneration and epiphyte colonization will likely be present in forests with a basal area ≥27 m 2 /ha. We recommend that urban forest restoration plantings be designed to promote rapid canopy closure to reduce light availability, suppress herbaceous weeds, and stabilize the microclimate. © 2017 by the Ecological Society of America.

Evaluation of an urban canopy model in a tropical city: the role of tree evapotranspiration

NASA Astrophysics Data System (ADS)

Liu, Xuan; Li, Xian-Xiang; Harshan, Suraj; Roth, Matthias; Velasco, Erik

2017-09-01

A single layer urban canopy model (SLUCM) with enhanced hydrologic processes, is evaluated in a tropical city, Singapore. The evaluation was performed using an 11 month offline simulation with the coupled Noah land surface model/SLUCM over a compact low-rise residential area. Various hydrological processes are considered, including anthropogenic latent heat release, and evaporation from impervious urban facets. Results show that the prediction of energy fluxes, in particular latent heat flux, is improved when these processes were included. However, the simulated latent heat flux is still underestimated by ∼40%. Considering Singapore’s high green cover ratio, the tree evapotranspiration process is introduced into the model, which significantly improves the simulated latent heat flux. In particular, the systematic error of the model is greatly reduced, and becomes lower than the unsystematic error in some seasons. The effect of tree evapotranspiration on the urban surface energy balance is further demonstrated during an unusual dry spell. The present study demonstrates that even at sites with relatively low (11%) tree coverage, ignoring evapotranspiration from trees may cause serious underestimation of the latent heat flux and atmospheric humidity. The improved model is also transferable to other tropical or temperate regions to study the impact of tree evapotranspiration on urban climate.

Projection of Summer Climate on Tokyo Metropolitan Area using Pseudo Global Warming Method

NASA Astrophysics Data System (ADS)

Adachi, S. A.; Kimura, F.; Kusaka, H.; Hara, M.

2010-12-01

Recent surface air temperature observations in most of urban areas show the remarkable increasing trend affected by the global warming and the heat island effects. There are many populous areas in Japan. In such areas, the effects of land-use change and urbanization on the local climate are not negligible (Fujibe, 2010). The heat stress for citizen there is concerned to swell moreover in the future. Therefore, spatially detailed climate projection is required for making adaptation and mitigation plans. This study focuses on the Tokyo metropolitan area (TMA) in summer and aims to estimate the local climate change over the TMA in 2070s using a regional climate model. The Regional Atmospheric Modeling System (RAMS) was used for downscaling. A single layer urban canopy model (Kusaka et al., 2001) is built into RAMS as a parameterization expressing the features of urban surface. We performed two experiments for estimating present and future climate. In the present climate simulation, the initial and boundary conditions for RAMS are provided from the JRA-25/JCDAS. On the other hand, the Pseudo Global Warming (PGW) method (Sato et al., 2007) is applied to estimate the future climate, instead of the conventional dynamical downscaling method. The PGW method is expected to reduce the model biases in the future projection estimated by Atmosphere-Ocean General Circulation Models (AOGCM). The boundary conditions used in the PGW method is given by the PGW data, which are obtained by adding the climate monthly difference between 1990s and 2070s estimated by AOGCMs to the 6-hourly reanalysis data. In addition, the uncertainty in the regional climate projection depending on the AOGCM projections is estimated from additional downscaling experiments using the different PGW data obtained from five AOGCMs. Acknowledgment: This work was supported by the Global Environment Research Fund (S-5-3) of the Ministry of the Environment, Japan. References: 1. Fujibe, F., Int. J. Climatol., doi:10.1002/joc.2142 (2010). 2. Kusaka, H., H. Kondo, Y. Kikegawa, and F. Kimura, Bound.-Layer Meteor., 101, 329-358 (2001). 3. Sato, T., F. Kimura, and A. Kitoh, J. Hydrology, 144-154 (2007).

Effects of anthropogenic heat due to air-conditioning systems on an extreme high temperature event in Hong Kong

NASA Astrophysics Data System (ADS)

Wang, Y.; Li, Y.; Di Sabatino, S.; Martilli, A.; Chan, P. W.

2018-03-01

Anthropogenic heat flux is the heat generated by human activities in the urban canopy layer, which is considered the main contributor to the urban heat island (UHI). The UHI can in turn increase the use and energy consumption of air-conditioning systems. In this study, two effective methods for water-cooling air-conditioning systems in non-domestic areas, including the direct cooling system and central piped cooling towers (CPCTs), are physically based, parameterized, and implemented in a weather research and forecasting model at the city scale of Hong Kong. An extreme high temperature event (June 23-28, 2016) in the urban areas was examined, and we assessed the effects on the surface thermal environment, the interaction of sea-land breeze circulation and urban heat island circulation, boundary layer dynamics, and a possible reduction of energy consumption. The results showed that both water-cooled air-conditioning systems could reduce the 2 m air temperature by around 0.5 °C-0.8 °C during the daytime, and around 1.5 °C around 7:00-8:00 pm when the planetary boundary layer (PBL) height was confined to a few hundred meters. The CPCT contributed around 80%-90% latent heat flux and significantly increased the water vapor mixing ratio in the atmosphere by around 0.29 g kg-1 on average. The implementation of the two alternative air-conditioning systems could modify the heat and momentum of turbulence, which inhibited the evolution of the PBL height (a reduction of 100-150 m), reduced the vertical mixing, presented lower horizontal wind speed and buoyant production of turbulent kinetic energy, and reduced the strength of sea breeze and UHI circulation, which in turn affected the removal of air pollutants. Moreover, the two alternative air-conditioning systems could significantly reduce the energy consumption by around 30% during extreme high temperature events. The results of this study suggest potential UHI mitigation strategies and can be extended to other megacities to enable them to be more resilient to UHI effects.

Canopy-scale biophysical controls of transpiration and evaporation in the Amazon Basin

NASA Astrophysics Data System (ADS)

Mallick, Kaniska; Trebs, Ivonne; Boegh, Eva; Giustarini, Laura; Schlerf, Martin; Drewry, Darren T.; Hoffmann, Lucien; von Randow, Celso; Kruijt, Bart; Araùjo, Alessandro; Saleska, Scott; Ehleringer, James R.; Domingues, Tomas F.; Ometto, Jean Pierre H. B.; Nobre, Antonio D.; Leal de Moraes, Osvaldo Luiz; Hayek, Matthew; Munger, J. William; Wofsy, Steven C.

2016-10-01

Canopy and aerodynamic conductances (gC and gA) are two of the key land surface biophysical variables that control the land surface response of land surface schemes in climate models. Their representation is crucial for predicting transpiration (λET) and evaporation (λEE) flux components of the terrestrial latent heat flux (λE), which has important implications for global climate change and water resource management. By physical integration of radiometric surface temperature (TR) into an integrated framework of the Penman-Monteith and Shuttleworth-Wallace models, we present a novel approach to directly quantify the canopy-scale biophysical controls on λET and λEE over multiple plant functional types (PFTs) in the Amazon Basin. Combining data from six LBA (Large-scale Biosphere-Atmosphere Experiment in Amazonia) eddy covariance tower sites and a TR-driven physically based modeling approach, we identified the canopy-scale feedback-response mechanism between gC, λET, and atmospheric vapor pressure deficit (DA), without using any leaf-scale empirical parameterizations for the modeling. The TR-based model shows minor biophysical control on λET during the wet (rainy) seasons where λET becomes predominantly radiation driven and net radiation (RN) determines 75 to 80 % of the variances of λET. However, biophysical control on λET is dramatically increased during the dry seasons, and particularly the 2005 drought year, explaining 50 to 65 % of the variances of λET, and indicates λET to be substantially soil moisture driven during the rainfall deficit phase. Despite substantial differences in gA between forests and pastures, very similar canopy-atmosphere "coupling" was found in these two biomes due to soil moisture-induced decrease in gC in the pasture. This revealed the pragmatic aspect of the TR-driven model behavior that exhibits a high sensitivity of gC to per unit change in wetness as opposed to gA that is marginally sensitive to surface wetness variability. Our results reveal the occurrence of a significant hysteresis between λET and gC during the dry season for the pasture sites, which is attributed to relatively low soil water availability as compared to the rainforests, likely due to differences in rooting depth between the two systems. Evaporation was significantly influenced by gA for all the PFTs and across all wetness conditions. Our analytical framework logically captures the responses of gC and gA to changes in atmospheric radiation, DA, and surface radiometric temperature, and thus appears to be promising for the improvement of existing land-surface-atmosphere exchange parameterizations across a range of spatial scales.

The transient behavior of whole-canopy fluxes during dynamic light conditions for midlatitude and tropical forests

NASA Astrophysics Data System (ADS)

Fitzjarrald, D. R.; Kivalov, S. N.

2017-12-01

Cloud shadows lead to alternating light and dark periods at the surface. Understanding how clouds affect whole-canopy fluxes suffer from two knowledge gaps that limit scaling from leaf to canopy scales, an effort currently done by assertion alone. First, there is a lack a clear quantitative definition of the incident light time series that occur on specific types of cloudy days. Second, the characteristic time scales for leaves to respond to for stomatal opening and closing is 1-10 minutes, a period too short to allow accurate eddy fluxes. We help to close the first gap by linking the durations of alternating light and dark periods statistically to conventional meteorological sky types at a midlatitude mixed deciduous forest (Harvard Forest, MA, USA: 42.53N, 72.17W) and in a tropical rain forest (Tapajós National Forest, Brazil; 2.86S, 54.96W). The second gap is narrowed by measuring the dynamic response whole canopy exchanges in the flux footprint at intervals of only a few seconds using the classical ensemble average method, keying on step changes in light intensity. Combining light and shadow periods of different lengths we estimate ensemble fluxes sensible heat (H), net ecosystem exchange (NEE), and latent heat (LE) fluxes initiated by abrupt radiation changes at intervals of 30 s over 20 minutes. We present composite results of the transient behavior of whole-canopy fluxes at each forest, showing distinct features of each forest type. Observed time constants and transient flux parameterizations are then used to force a simple model to yield NEE, LE, WUE, and Bowen ratio extrema under periodic shadow-light conditions and given cloud amount. We offer the hypothesis that, at least on certain types of cloudy days, the well-known correlation between diffuse light and WUE does not represent a causal connection at the canopy scale.

Simulating Urban Tree Effects on Air, Water, and Heat Pollution Mitigation: iTree-Hydro Model

NASA Astrophysics Data System (ADS)

Yang, Y.; Endreny, T. A.; Nowak, D.

2011-12-01

Urban and suburban development changes land surface thermal, radiative, porous, and roughness properties and pollutant loading rates, with the combined effect leading to increased air, water, and heat pollution (e.g., urban heat islands). In this research we present the USDA Forest Service urban forest ecosystem and hydrology model, iTree Eco and Hydro, used to analyze how tree cover can deliver valuable ecosystem services to mitigate air, water, and heat pollution. Air pollution mitigation is simulated by dry deposition processes based on detected pollutant levels for CO, NO2, SO2, O3 and atmospheric stability and leaf area indices. Water quality mitigation is simulated with event mean concentration loading algorithms for N, P, metals, and TSS, and by green infrastructure pollutant filtering algorithms that consider flow path dispersal areas. Urban cooling considers direct shading and indirect evapotranspiration. Spatially distributed estimates of hourly tree evapotranspiration during the growing season are used to estimate human thermal comfort. Two main factors regulating evapotranspiration are soil moisture and canopy radiation. Spatial variation of soil moisture is represented by a modified urban topographic index and radiation for each tree is modified by considering aspect, slope and shade from surrounding buildings or hills. We compare the urban cooling algorithms used in iTree-Hydro with the urban canopy and land surface physics schemes used in the Weather Research and Forecasting model. We conclude by identifying biophysical feedbacks between tree-modulated air and water quality environmental services and how these may respond to urban heating and cooling. Improvements to this iTree model are intended to assist managers identify valuable tree services for urban living.

Albedo, Land Cover, and Daytime Surface Temperature Variation Across an Urbanized Landscape

NASA Astrophysics Data System (ADS)

Trlica, A.; Hutyra, L. R.; Schaaf, C. L.; Erb, A.; Wang, J. A.

2017-11-01

Land surface albedo is a key parameter controlling the local energy budget, and altering the albedo of built surfaces has been proposed as a tool to mitigate high near-surface temperatures in the urban heat island. However, most research on albedo in urban landscapes has used coarse-resolution data, and few studies have attempted to relate albedo to other urban land cover characteristics. This study provides an empirical description of urban summertime albedo using 30 m remote sensing measurements in the metropolitan area around Boston, Massachusetts, relating albedo to metrics of impervious cover fraction, tree canopy coverage, population density, and land surface temperature (LST). At 30 m spatial resolution, median albedo over the study area (excluding open water) was 0.152 (0.112-0.187). Trends of lower albedo with increasing urbanization metrics and temperature emerged only after aggregating data to 500 m or the boundaries of individual towns, at which scale a -0.01 change in albedo was associated with a 29 (25-35)% decrease in canopy cover, a 27 (24-30)% increase in impervious cover, and an increase in population from 11 to 386 km-2. The most intensively urbanized towns in the region showed albedo up to 0.035 lower than the least urbanized towns, and mean mid-morning LST 12.6°C higher. Trends in albedo derived from 500 m Moderate Resolution Imaging Spectroradiometer (MODIS) measurements were comparable, but indicated a strong contribution of open water at this coarser resolution. These results reveal linkages between albedo and urban land cover character, and offer empirical context for climate resilient planning and future landscape functional changes with urbanization.

The urban forests of Philadelphia

Treesearch

David J. Nowak; Allison R. Bodine; Robert Hoehn; Alexis Ellis; Sarah C. Low; Lara A. Roman; Jason G. Henning; Emily Stephan; Tom Taggert; Ted Endreny

2016-01-01

An analysis of the urban forest in Philadelphia, Pennsylvania, reveals that this city has an estimated 2.9 million trees (encompassing all woody plants greater than 1 inch diameter at breast height [d.b.h]) with tree canopy that covers 20 percent of the city. The most common tree species are spicebush, black cherry, ash, tree-of-heaven, and boxelder, but the most...

Austin's Urban Forest, 2014

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Christopher B. Edgar; Dudley R. Hartel; Tonya W. Lister; Thomas J. Brandeis

2016-01-01

An analysis of the urban forest in Austin, Texas, reveals that this area has an estimated 33.8 million trees with tree canopy that covers 30.8 percent of the city. The most common tree species are Ashe juniper, cedar elm, live oak, sugarberry, and Texas persimmon. Trees in Austin currently store about 1.9 million tons of carbon (7.0 million tons of carbon dioxide [CO...

Energy flux parametrization as an opportunity to get Urban Heat Island insights: The case of Athens, Greece (Thermopolis 2009 Campaign).

PubMed

Loupa, G; Rapsomanikis, S; Trepekli, A; Kourtidis, K

2016-01-15

Energy flux parameterization was effected for the city of Athens, Greece, by utilizing two approaches, the Local-Scale Urban Meteorological Parameterization Scheme (LUMPS) and the Bulk Approach (BA). In situ acquired data are used to validate the algorithms of these schemes and derive coefficients applicable to the study area. Model results from these corrected algorithms are compared with literature results for coefficients applicable to other cities and their varying construction materials. Asphalt and concrete surfaces, canyons and anthropogenic heat releases were found to be the key characteristics of the city center that sustain the elevated surface and air temperatures, under hot, sunny and dry weather, during the Mediterranean summer. A relationship between storage heat flux plus anthropogenic energy flux and temperatures (surface and lower atmosphere) is presented, that results in understanding of the interplay between temperatures, anthropogenic energy releases and the city characteristics under the Urban Heat Island conditions.

An evaluation of the performance of a WRF multi-physics ensemble for heatwave events over the city of Melbourne in southeast Australia

NASA Astrophysics Data System (ADS)

Imran, H. M.; Kala, J.; Ng, A. W. M.; Muthukumaran, S.

2018-04-01

Appropriate choice of physics options among many physics parameterizations is important when using the Weather Research and Forecasting (WRF) model. The responses of different physics parameterizations of the WRF model may vary due to geographical locations, the application of interest, and the temporal and spatial scales being investigated. Several studies have evaluated the performance of the WRF model in simulating the mean climate and extreme rainfall events for various regions in Australia. However, no study has explicitly evaluated the sensitivity of the WRF model in simulating heatwaves. Therefore, this study evaluates the performance of a WRF multi-physics ensemble that comprises 27 model configurations for a series of heatwave events in Melbourne, Australia. Unlike most previous studies, we not only evaluate temperature, but also wind speed and relative humidity, which are key factors influencing heatwave dynamics. No specific ensemble member for all events explicitly showed the best performance, for all the variables, considering all evaluation metrics. This study also found that the choice of planetary boundary layer (PBL) scheme had largest influence, the radiation scheme had moderate influence, and the microphysics scheme had the least influence on temperature simulations. The PBL and microphysics schemes were found to be more sensitive than the radiation scheme for wind speed and relative humidity. Additionally, the study tested the role of Urban Canopy Model (UCM) and three Land Surface Models (LSMs). Although the UCM did not play significant role, the Noah-LSM showed better performance than the CLM4 and NOAH-MP LSMs in simulating the heatwave events. The study finally identifies an optimal configuration of WRF that will be a useful modelling tool for further investigations of heatwaves in Melbourne. Although our results are invariably region-specific, our results will be useful to WRF users investigating heatwave dynamics elsewhere.

[Species composition and spatial structure of plants in urban parks of Beijing].

PubMed

Zhao, Juan-Juan; Ouyang, Zhi-Yun; Zheng, Hua; Xu, Wei-Hua; Wang, Xiao-Ke

2009-02-01

By the method of stratified random sampling, the species composition and spatial structure of the plants in 53 parks in Beijing urban area were investigated, aimed to provide basic information for the protection of plant diversity in the parks and the management of the parks. A total of 492 plant species belong to 96 families and 283 genera were recorded. Based on the data of 21 investigation items about the trees, shrubs, and grasses in the study area and related statistical analyses, the plant structural patterns commonly seen in the green space of the parks of Beijing urban area were introduced. Among the plants in the parks, native species occupied 53.86% of the total. The chorological composition of the genera embraced broad kinds of geographical elements in China, and the predominance of dominant plants was remarkable. In most green patches of the parks, herbaceous species were more abundant and had higher coverage, shrubs had relatively low coverage and were less beneath tree canopy, and trees and shrubs had lower species richness and density. The canopy breadth and the diameter of breast height of trees as well as the breadth of shrubs and the heights of trees and shrubs were basically at the second grade, but the canopy structure of the trees were better, with good conditions of sunlight and growth. The crown missing of the shrubs was relatively low. It was suggested from correlation analyses and document survey of Beijing parks construction history that park landscape design, alien species introduction; and cultivation management were the main factors affecting the species composition and spatial structure of the plants in Beijing urban parks.

Biological and environmental controls on tree transpiration in a suburban landscape

NASA Astrophysics Data System (ADS)

Peters, Emily B.; McFadden, Joseph P.; Montgomery, Rebecca A.

2010-12-01

Tree transpiration provides a variety of ecosystem services in urban areas, including amelioration of urban heat island effects and storm water management. Tree species vary in the magnitude and seasonality of transpiration owing to differences in physiology, response to climate, and biophysical characteristics, thereby complicating efforts to manage evapotranspiration at city scales. We report sap flux measurements during the 2007 and 2008 growing seasons for dominant tree species in a suburban neighborhood of Minneapolis-Saint Paul, Minnesota, USA. Evergreen needleleaf trees had significantly higher growing season means and annual transpiration per unit canopy area (1.90 kg H2O m-2 d-1 and 307 kg H2O m-2 yr-1, respectively) than deciduous broadleaf trees (1.11 kg H2O m-2 d-1 and 153 kg H2O m-2 yr-1, respectively) because of a smaller projected canopy area (31.1 and 73.6 m2, respectively), a higher leaf area index (8.8 and 5.5 m2 m-2, respectively), and a longer growth season (8 and 4 months, respectively). Measurements also showed patterns consistent with the species' differences in xylem anatomy (conifer, ring porous, and diffuse porous). As the growing season progressed, conifer and diffuse porous genera had increased stomatal regulation to high vapor pressure deficit, while ring porous genera maintained greater and more constant stomatal regulation. These results suggest that evaporative responses to climate change in urban ecosystems will depend in part on species composition. Overall, plant functional type differences in canopy structure and growing season length were most important in explaining species' differences in midsummer and annual transpiration, offering an approach to predicting the evapotranspiration component of urban water budgets.

An analytically based numerical method for computing view factors in real urban environments

NASA Astrophysics Data System (ADS)

Lee, Doo-Il; Woo, Ju-Wan; Lee, Sang-Hyun

2018-01-01

A view factor is an important morphological parameter used in parameterizing in-canyon radiative energy exchange process as well as in characterizing local climate over urban environments. For realistic representation of the in-canyon radiative processes, a complete set of view factors at the horizontal and vertical surfaces of urban facets is required. Various analytical and numerical methods have been suggested to determine the view factors for urban environments, but most of the methods provide only sky-view factor at the ground level of a specific location or assume simplified morphology of complex urban environments. In this study, a numerical method that can determine the sky-view factors ( ψ ga and ψ wa ) and wall-view factors ( ψ gw and ψ ww ) at the horizontal and vertical surfaces is presented for application to real urban morphology, which are derived from an analytical formulation of the view factor between two blackbody surfaces of arbitrary geometry. The established numerical method is validated against the analytical sky-view factor estimation for ideal street canyon geometries, showing a consolidate confidence in accuracy with errors of less than 0.2 %. Using a three-dimensional building database, the numerical method is also demonstrated to be applicable in determining the sky-view factors at the horizontal (roofs and roads) and vertical (walls) surfaces in real urban environments. The results suggest that the analytically based numerical method can be used for the radiative process parameterization of urban numerical models as well as for the characterization of local urban climate.

A comprehensive approach for the simulation of the Urban Heat Island effect with the WRF/SLUCM modeling system: The case of Athens (Greece)

NASA Astrophysics Data System (ADS)

Giannaros, Christos; Nenes, Athanasios; Giannaros, Theodore M.; Kourtidis, Konstantinos; Melas, Dimitrios

2018-03-01

This study presents a comprehensive modeling approach for simulating the spatiotemporal distribution of urban air temperatures with a modeling system that includes the Weather Research and Forecasting (WRF) model and the Single-Layer Urban Canopy Model (SLUCM) with a modified treatment of the impervious surface temperature. The model was applied to simulate a 3-day summer heat wave event over the city of Athens, Greece. The simulation, using default SLUCM parameters, is capable of capturing the observed diurnal variation of urban temperatures and the Urban Heat Island (UHI) in the greater Athens Area (GAA), albeit with systematic biases that are prominent during nighttime hours. These biases are particularly evident over low-intensity residential areas, and they are associated with the surface and urban canopy properties representing the urban environment. A series of sensitivity simulations unravels the importance of the sub-grid urban fraction parameter, surface albedo, and street canyon geometry in the overall causation and development of the UHI effect. The sensitivities are then used to determine optimal values of the street canyon geometry, which reproduces the observed temperatures throughout the simulation domain. The optimal parameters, apart from considerably improving model performance (reductions in mean temperature bias from 0.30 °C to 1.58 °C), are also consistent with actual city building characteristics - which gives confidence that the model set-up is robust, and can be used to study the UHI in the GAA in the anticipated warmer conditions in the future.

Parametrizing Evaporative Resistance for Heterogeneous Sparse Canopies through Novel Wind Tunnel Experimentation

NASA Astrophysics Data System (ADS)

Sloan, B.; Ebtehaj, A. M.; Guala, M.

2017-12-01

The understanding of heat and water vapor transfer from the land surface to the atmosphere by evapotranspiration (ET) is crucial for predicting the hydrologic water balance and climate forecasts used in water resources decision-making. However, the complex distribution of vegetation, soil and atmospheric conditions makes large-scale prognosis of evaporative fluxes difficult. Current ET models, such as Penman-Monteith and flux-gradient methods, are challenging to apply at the microscale due to ambiguity in determining resistance factors to momentum, heat and vapor transport for realistic landscapes. Recent research has made progress in modifying Monin-Obukhov similarity theory for dense plant canopies as well as providing clearer description of diffusive controls on evaporation at a smooth soil surface, which both aid in calculating more accurate resistance parameters. However, in nature, surfaces typically tend to be aerodynamically rough and vegetation is a mixture of sparse and dense canopies in non-uniform configurations. The goal of our work is to parameterize the resistances to evaporation based on spatial distributions of sparse plant canopies using novel wind tunnel experimentation at the St. Anthony Falls Laboratory (SAFL). The state-of-the-art SAFL wind tunnel was updated with a retractable soil box test section (shown in Figure 1), complete with a high-resolution scale and soil moisture/temperature sensors for recording evaporative fluxes and drying fronts. The existing capabilities of the tunnel were used to create incoming non-neutral stability conditions and measure 2-D velocity fields as well as momentum and heat flux profiles through PIV and hotwire anemometry, respectively. Model trees (h = 5 cm) were placed in structured and random configurations based on a probabilistic spacing that was derived from aerial imagery. The novel wind tunnel dataset provides the surface energy budget, turbulence statistics and spatial soil moisture data under varying atmospheric stability for each sparse canopy configuration. We will share initial data results and progress toward the development of new parametrizations that can account for the evolution of a canopy roughness sublayer on the momentum, heat and vapor resistance terms as a function of a stochastic representation of canopy spacing.

Impact of urbanization-related land use land cover changes and urban morphology changes on the urban heat island phenomenon.

PubMed

Zhou, Xuefan; Chen, Hong

2018-04-24

Urban growth and development caused by urbanization influence the urban heat island (UHI) phenomenon. With the rapid development of urbanization, China's major cities are facing more serious climate change problems, especially the UHI phenomenon. Proper planning and urban design of compact cities may improve the ventilation of street canyons and change the heat balance in the urban canopy and thus mitigate the UHI phenomenon. The aim of this study is to evaluate and discuss the mitigation of UHI with different types of land-use and land-cover (LUCC), as well as different development patterns for compact cities. To this end, we applied the weather research and forecasting model (WRF) with urban canopy model (WRF/UCM) in this study. To evaluate the impact of LUCC changes on the UHI, we set 2 cases based on land use and land cover statistical data from 1965 and 2008 of Wuhan. Also, to evaluate the impact of urban morphology changes on the UHI, we designed 2 hypothetical cases based on 2 different urban developing patterns, one is high rise case and another is high density case, to simulate the impact of urban morphology on the UHI. As for the results of this study, with different LUCC of 1965 and 2008, UHI intensity of Wuhan increased by 0.2 °C-0.4 °C in average. Moreover, the critical wind speed which can mitigate UHI of case 1965 is much lower than case 2008. With different urban morphology, the high-rise case may lead to lower UHI intensity at the pedestrian level due to the shading effects of high-rise buildings. However, the critical value of wind speed in the high-rise case was almost 1.5-2 times greater than that of the high-density case, which illustrates the reduced possibility of mitigating the UHI phenomenon for high-rise buildings in Wuhan City. Copyright © 2018 Elsevier B.V. All rights reserved.

The Canopy Conductance of a Humid Grassland

NASA Astrophysics Data System (ADS)

Lu, C. T.; Hsieh, C. I.

2015-12-01

Penman-Monteith equation is widely used for estimating latent heat flux. The key parameter for implementing this equation is the canopy conductance (gc). Recent research (Blaken and Black, 2004) showed that gc could be well parameterized by a linear function of An/ (D0* X0c), where An represents net assimilation, D0 is leaf level saturation deficit, and X0c is CO2 mole fraction. In this study, we tried to use the same idea for estimating gcfor a humid grassland. The study site was located in County Cork, southwest Ireland (51o59''N 8o46''W), and perennial ryegrass (Lolium perenne L.) was the dominant grass species in this area. An eddy covariance system was used to measure the latent heat flux above this humid grassland. The measured gc was calculated by rearranging Penman-Monteith equation combined with the measured latent heat flux. Our data showed that the gc decreased as the vapor pressure deficit and temperature increased. And it increased as the net radiation increased. Therefore, we found out that the best parameterization of gc was a linear function of the product of the vapor deficit, temperature, and net radiation. Also, we used the gc which was estimated by this linear function to predict the latent heat flux by Penman-Monteith equation and compared the predictions with those where the gc was chosen to be a fixed value. Our analysis showed that this simple linear function for gc can improve the latent heat flux predictions (R square increased from 0.48 to 0.66).

Investigating the relationship between tree heights derived from SIBBORK forest model and remote sensing measurements

NASA Astrophysics Data System (ADS)

Osmanoglu, B.; Feliciano, E. A.; Armstrong, A. H.; Sun, G.; Montesano, P.; Ranson, K.

2017-12-01

Tree heights are one of the most commonly used remote sensing parameters to measure biomass of a forest. In this project, we investigate the relationship between remotely sensed tree heights (e.g. G-LiHT lidar and commercially available high resolution satellite imagery, HRSI) and the SIBBORK modeled tree heights. G-LiHT is a portable, airborne imaging system that simultaneously maps the composition, structure, and function of terrestrial ecosystems using lidar, imaging spectroscopy and thermal mapping. Ground elevation and canopy height models were generated using the lidar data acquired in 2012. A digital surface model was also generated using the HRSI technique from the commercially available WorldView data in 2016. The HRSI derived height and biomass products are available at the plot (10x10m) level. For this study, we parameterized the SIBBORK individual-based gap model for Howland forest, Maine. The parameterization was calibrated using field data for the study site and results show that the simulated forest reproduces the structural complexity of Howland old growth forest, based on comparisons of key variables including, aboveground biomass, forest height and basal area. Furthermore carbon cycle and ecosystem observational capabilities will be enhanced over the next 6 years via the launch of two LiDAR (NASA's GEDI and ICESAT 2) and two SAR (NASA's ISRO NiSAR and ESA's Biomass) systems. Our aim is to present the comparison of canopy height models obtained with SIBBORK forest model and remote sensing techniques, highlighting the synergy between individual-based forest modeling and high-resolution remote sensing.

Monitoring phenology of photosynthesis in temperate evergreen and mixed deciduous forests using the normalized difference vegetation index (NDVI) and the photochemical reflectance index (PRI) at leaf and canopy scales

NASA Astrophysics Data System (ADS)

Wong, C. Y.; Arain, M. A.; Ensminger, I.

2016-12-01

Evergreen conifers in boreal and temperate regions undergo strong seasonal changes in photoperiod and temperatures, which determines their phenology of high photosynthetic activity in the growing season and downregulation during the winter. Monitoring the timing of the transition between summer activity and winter downregulation in evergreens is difficult since this is a largely invisible process, unlike in deciduous trees that have a visible budding and a sequence of leaf unfolding in the spring and leaf abscission in the fall. The light-use efficiency (LUE) model estimates gross primary productivity (GPP) and may be parameterized using remotely sensed vegetation indices. Using spectral reflectance data, we derived the normalized difference vegetation index (NDVI), a measure of leaf "greenness", and the photochemical reflectance index (PRI), a proxy for chlorophyll:carotenoid ratios which is related to photosynthetic activity. To better understand the relationship between these vegetation indices and photosynthetic activity and to contrast this relationship between plant functional types, the phenology of NDVI, PRI and photosynthesis was monitored in an evergreen forest and a mixed deciduous forest at the leaf and canopy scale. Our data indicates that the LUE model can be parameterized by NDVI and PRI to track forest phenology. Differences in the sensitivity of PRI and NDVI will be discussed. These findings have implications to address the phenology of evergreen conifers by using PRI to complement NDVI in the LUE model, potentially improving model productivity estimates in northern hemisphere forests, that are dominated by conifers.

Biogeographic variation in evergreen conifer needle longevity and impacts on boreal forest carbon cycle projections

PubMed Central

Reich, Peter B.; Rich, Roy L.; Lu, Xingjie; Wang, Ying-Ping; Oleksyn, Jacek

2014-01-01

Leaf life span is an important plant trait associated with interspecific variation in leaf, organismal, and ecosystem processes. We hypothesized that intraspecific variation in gymnosperm needle traits with latitude reflects both selection and acclimation for traits adaptive to the associated temperature and moisture gradient. This hypothesis was supported, because across 127 sites along a 2,160-km gradient in North America individuals of Picea glauca, Picea mariana, Pinus banksiana, and Abies balsamea had longer needle life span and lower tissue nitrogen concentration with decreasing mean annual temperature. Similar patterns were noted for Pinus sylvestris across a north–south gradient in Europe. These differences highlight needle longevity as an adaptive feature important to ecological success of boreal conifers across broad climatic ranges. Additionally, differences in leaf life span directly affect annual foliage turnover rate, which along with needle physiology partially regulates carbon cycling through effects on gross primary production and net canopy carbon export. However, most, if not all, global land surface models parameterize needle longevity of boreal evergreen forests as if it were a constant. We incorporated temperature-dependent needle longevity and %nitrogen, and biomass allocation, into a land surface model, Community Atmosphere Biosphere Land Exchange, to assess their impacts on carbon cycling processes. Incorporating realistic parameterization of these variables improved predictions of canopy leaf area index and gross primary production compared with observations from flux sites. Finally, increasingly low foliage turnover and biomass fraction toward the cold far north indicate that a surprisingly small fraction of new biomass is allocated to foliage under such conditions. PMID:25225397

Evaluation of improved land use and canopy representation in ...

EPA Pesticide Factsheets

Biogenic volatile organic compounds (BVOC) participate in reactions that can lead to secondarily formed ozone and particulate matter (PM) impacting air quality and climate. BVOC emissions are important inputs to chemical transport models applied on local to global scales but considerable uncertainty remains in the representation of canopy parameterizations and emission algorithms from different vegetation species. The Biogenic Emission Inventory System (BEIS) has been used to support both scientific and regulatory model assessments for ozone and PM. Here we describe a new version of BEIS which includes updated input vegetation data and canopy model formulation for estimating leaf temperature and vegetation data on estimated BVOC. The Biogenic Emission Landuse Database (BELD) was revised to incorporate land use data from the Moderate Resolution Imaging Spectroradiometer (MODIS) land product and 2006 National Land Cover Database (NLCD) land coverage. Vegetation species data are based on the US Forest Service (USFS) Forest Inventory and Analysis (FIA) version 5.1 for 2002–2013 and US Department of Agriculture (USDA) 2007 census of agriculture data. This update results in generally higher BVOC emissions throughout California compared with the previous version of BEIS. Baseline and updated BVOC emission estimates are used in Community Multiscale Air Quality (CMAQ) Model simulations with 4 km grid resolution and evaluated with measurements of isoprene and monoterp

Modeling Stand-Scale Patterns in Evapotranspiration and Soil Moisture in a Heterogeneous Plant Canopy: A Coupled Subsurface-Land Surface Approach

NASA Astrophysics Data System (ADS)

Miller, G. R.; Gou, S.; Ferguson, I. M.; Maxwell, R. M.

2011-12-01

Savanna ecosystems present a well-known modeling challenge; understory grasses and overstory woody vegetation combine to form an open, heterogeneous canopy that creates strong spatial differences in soil moisture and evapotranspiration rates. In this analysis, we used ParFlow.CLM to create a stand-scale model of the Tonzi Ranch oak savanna, based on extensive topography, vegetation, soil, and hydrogeology data collected at the site. Measurements included canopy distribution and ground surface elevation from airborne Lidar, depth to groundwater from deep piezometers, soil and rock hydraulic conductivity, and leaf area index. We then compared the results to the site's long-term data records of radiative flux partitioning, obtained using the eddy-covariance method, and soil moisture, collected via a distributed network of capacitance probes. In order to obtain good agreement between the measured and modeled values, we identified several necessary modifications to the current CLM parameterization. These changes included the addition of a "winter grass" type and the alteration of the root structure and water stress functions to accommodate uptake of groundwater by deep roots. Finally, we compared variograms of site parameters and response variables and performed a scaling analysis relating ET and soil moisture variance to sampling size.

Modeling the Surface Energy Balance of the Core of an Old Mediterranean City: Marseille.

NASA Astrophysics Data System (ADS)

Lemonsu, A.; Grimmond, C. S. B.; Masson, V.

2004-02-01

The Town Energy Balance (TEB) model, which parameterizes the local-scale energy and water exchanges between urban surfaces and the atmosphere by treating the urban area as a series of urban canyons, coupled to the Interactions between Soil, Biosphere, and Atmosphere (ISBA) scheme, was run in offline mode for Marseille, France. TEB's performance is evaluated with observations of surface temperatures and surface energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) urban boundary layer (UBL) campaign. Particular attention was directed to the influence of different surface databases, used for input parameters, on model predictions. Comparison of simulated canyon temperatures with observations resulted in improvements to TEB parameterizations by increasing the ventilation. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model succeeds in simulating a sensible heat flux larger than heat storage, as observed. A sensitivity comparison using generic dense city parameters, derived from the Coordination of Information on the Environment (CORINE) land cover database, and those from a surface database developed specifically for the Marseille city center shows the importance of correctly documenting the urban surface. Overall, the TEB scheme is shown to be fairly robust, consistent with results from previous studies.

A New Scheme for the Simulation of Microscale Flow and Dispersion in Urban Areas by Coupling Large-Eddy Simulation with Mesoscale Models

NASA Astrophysics Data System (ADS)

Li, Haifeng; Cui, Guixiang; Zhang, Zhaoshun

2018-04-01

A coupling scheme is proposed for the simulation of microscale flow and dispersion in which both the mesoscale field and small-scale turbulence are specified at the boundary of a microscale model. The small-scale turbulence is obtained individually in the inner and outer layers by the transformation of pre-computed databases, and then combined in a weighted sum. Validation of the results of a flow over a cluster of model buildings shows that the inner- and outer-layer transition height should be located in the roughness sublayer. Both the new scheme and the previous scheme are applied in the simulation of the flow over the central business district of Oklahoma City (a point source during intensive observation period 3 of the Joint Urban 2003 experimental campaign), with results showing that the wind speed is well predicted in the canopy layer. Compared with the previous scheme, the new scheme improves the prediction of the wind direction and turbulent kinetic energy (TKE) in the canopy layer. The flow field influences the scalar plume in two ways, i.e. the averaged flow field determines the advective flux and the TKE field determines the turbulent flux. Thus, the mean, root-mean-square and maximum of the concentration agree better with the observations with the new scheme. These results indicate that the new scheme is an effective means of simulating the complex flow and dispersion in urban canopies.

Heat transfer to and from vegetated surfaces - An analytical method for the bulk exchange coefficients

NASA Technical Reports Server (NTRS)

Massman, William J.

1987-01-01

The semianalytical model outlined in a previous study (Massman, 1987) to describe momentum exchange between the atmosphere and vegetated surfaces is extended to include the exchange of heat. The methods employed are based on one-dimensional turbulent diffusivities, and use analytical solutions to the steady-state diffusion equation. The model is used to assess the influence that the canopy foliage structure and density, the wind profile structure within the canopy, and the shelter factor can have upon the inverse surface Stanton number (kB exp -1), as well as to explore the consequences of introducing a scalar displacement height which can be different from the momentum displacement height. In general, the triangular foliage area density function gives results which agree more closely with observations than that for constant foliage area density. The intended application of this work is for parameterizing the bulk aerodynamic resistances for heat and momentum exchange for use within large-scale models of plant-atmosphere exchanges.

Urbanization alters communities of flying arthropods in parks and gardens of a medium-sized city.

PubMed

Lagucki, Edward; Burdine, Justin D; McCluney, Kevin E

2017-01-01

Urbanization transforms undeveloped landscapes into built environments, causing changes in communities and ecological processes. Flying arthropods play important roles in these processes as pollinators, decomposers, and predators, and can be important in structuring food webs. The goal of this study was to identify associations between urbanization and the composition of communities of flying (and floating) arthropods within gardens and parks in a medium-sized mesic city. We predicted that flying arthropod abundance and diversity would respond strongly to percent impervious surface and distance to city center, measurements of urbanization. Flying arthropods were sampled from 30 gardens and parks along an urbanization gradient in Toledo, Ohio, during July and August 2016, using elevated pan traps. A variety of potential predictor variables were also recorded at each site. We collected a total of 2,369 individuals representing nine orders. We found that flying arthropod community composition was associated with percent impervious surface and canopy cover. Overall flying arthropod abundance was negatively associated with percent impervious surface and positively associated with distance to city center. Hymenoptera (bees, wasps, ants), Lepidoptera (moths, butterflies), and Araneae (spiders) were positively associated with distance to city center. Hemiptera (true bugs), Diptera (flies), and Araneae were negatively associated with percent impervious surface. Both distance to city center and percent impervious surface are metrics of urbanization, and this study shows how these factors influence flying arthropod communities in urban gardens and city parks, including significant reductions in taxa that contain pollinators and predators important to urban agriculture and forestry. A variety of environmental factors also showed significant associations with responses (e.g. canopy cover and soil moisture), suggesting these factors may underlie or modulate the urbanization effects. More research is needed to determine mechanisms of change.

Urbanization alters communities of flying arthropods in parks and gardens of a medium-sized city

PubMed Central

Lagucki, Edward

2017-01-01

Urbanization transforms undeveloped landscapes into built environments, causing changes in communities and ecological processes. Flying arthropods play important roles in these processes as pollinators, decomposers, and predators, and can be important in structuring food webs. The goal of this study was to identify associations between urbanization and the composition of communities of flying (and floating) arthropods within gardens and parks in a medium-sized mesic city. We predicted that flying arthropod abundance and diversity would respond strongly to percent impervious surface and distance to city center, measurements of urbanization. Flying arthropods were sampled from 30 gardens and parks along an urbanization gradient in Toledo, Ohio, during July and August 2016, using elevated pan traps. A variety of potential predictor variables were also recorded at each site. We collected a total of 2,369 individuals representing nine orders. We found that flying arthropod community composition was associated with percent impervious surface and canopy cover. Overall flying arthropod abundance was negatively associated with percent impervious surface and positively associated with distance to city center. Hymenoptera (bees, wasps, ants), Lepidoptera (moths, butterflies), and Araneae (spiders) were positively associated with distance to city center. Hemiptera (true bugs), Diptera (flies), and Araneae were negatively associated with percent impervious surface. Both distance to city center and percent impervious surface are metrics of urbanization, and this study shows how these factors influence flying arthropod communities in urban gardens and city parks, including significant reductions in taxa that contain pollinators and predators important to urban agriculture and forestry. A variety of environmental factors also showed significant associations with responses (e.g. canopy cover and soil moisture), suggesting these factors may underlie or modulate the urbanization effects. More research is needed to determine mechanisms of change. PMID:28890848

Urban Tree Species Show the Same Hydraulic Response to Vapor Pressure Deficit across Varying Tree Size and Environmental Conditions

PubMed Central

Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E.

2012-01-01

Background The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. Methodology/Principal Findings We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E c) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G c at VPD = 1 kPa (G cref) and the G c sensitivity to VPD (−dG c/dlnVPD) across studied species as well as under contrasting soil water and R s conditions in the urban area. Conclusions/Significance We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G cref. PMID:23118904

Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

PubMed

Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E

2012-01-01

The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E(c)) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c) at VPD = 1 kPa (G(cref)) and the G(c) sensitivity to VPD (-dG(c)/dlnVPD) across studied species as well as under contrasting soil water and R(s) conditions in the urban area. We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref).

Validation of Martilli's urban boundary layer scheme with measurements from two mid-latitude European cities

NASA Astrophysics Data System (ADS)

Hamdi, R.; Schayes, G.

2007-08-01

Martilli's urban parameterization scheme is improved and implemented in a mesoscale model in order to take into account the typical effects of a real city on the air temperature near the ground and on the surface exchange fluxes. The mesoscale model is run on a single column using atmospheric data and radiation recorded above roof level as forcing. Here, the authors validate Martilli's urban boundary layer scheme using measurements from two mid-latitude European cities: Basel, Switzerland and Marseilles, France. For Basel, the model performance is evaluated with observations of canyon temperature, surface radiation, and energy balance fluxes obtained during the Basel urban boundary layer experiment (BUBBLE). The results show that the urban parameterization scheme represents correctly most of the behavior of the fluxes typical of the city center of Basel, including the large heat uptake by the urban fabric and the positive sensible heat flux at night. For Marseilles, the model performance is evaluated with observations of surface temperature, canyon temperature, surface radiation, and energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) and its urban boundary layer (UBL) campaign. At both urban sites, vegetation cover is less than 20%, therefore, particular attention was directed to the ability of Martilli's urban boundary layer scheme to reproduce the observations for the Marseilles city center, where the urban parameters and the synoptic forcing are totally different from Basel. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model correctly simulates the net radiation, canyon temperature, and the partitioning between the turbulent and storage heat fluxes.

Role of Vegetation and Mulch in Mitigating the Effects of Raindrop Impact on Runoff and Infiltration from Urban Vegetated Green Infrastructure

NASA Astrophysics Data System (ADS)

Alizadehtazi, B.; Montalto, F. A.

2013-12-01

Rain drop impact causes soil crust formation which, in turn, reduces infiltration rates and increases runoff, contributing to soil erosion, downstream flooding and non point source pollutant loads. Unprotected soil surfaces (e.g. without vegetation canopies, mulch, or other materials), are more susceptible to crust formation due to the higher kinetic energy associated with raindrop impact. This impulse breaks larger soil aggregates into smaller particles and disperses soil from its original position. The displaced soil particles self-stratify, with finer particles at the top forming the crust. By contrast, soil that is protected by vegetation canopies and mulch layers is less susceptible to crust formation, since these surfaces intercept raindrops, dissipating some of their kinetic energy prior to their impact with the soil. Very little research has sought to quantify the effect that canopies and mulch can have on this phenomenon. This presentation presents preliminary findings from ongoing study conducted using rainfall simulator to determine the ability of new urban vegetation and mulch to minimize soil crust formation. Three different scenarios are compared: a) bare soil, b) soil with mulch cover, and c) soil protected by vegetation canopies. Soil moisture, surface penetration resistance, and physical measurements of the volume of infiltrate and runoff are made on all three surface treatments after simulated rainfall events. The results are used to discuss green infrastructure facility maintenance and design strategies, namely whether heavily vegetated GI facilities require mulching to maintain infiltration capacity.

Smartphone based hemispherical photography for canopy structure measurement

NASA Astrophysics Data System (ADS)

Wan, Xuefen; Cui, Jian; Jiang, Xueqin; Zhang, Jingwen; Yang, Yi; Zheng, Tao

2018-01-01

The canopy is the most direct and active interface layer of the interaction between plant and environment, and has important influence on energy exchange, biodiversity, ecosystem matter and climate change. The measurement about canopy structure of plant is an important foundation to analyze the pattern, process and operation mechanism of forest ecosystem. Through the study of canopy structure of plant, solar radiation, ambient wind speed, air temperature and humidity, soil evaporation, soil temperature and other forest environmental climate characteristics can be evaluated. Because of its accuracy and effectiveness, canopy structure measurement based on hemispherical photography has been widely studied. However, the traditional method of canopy structure hemispherical photogrammetry based on SLR camera and fisheye lens. This method is expensive and difficult to be used in some low-cost occasions. In recent years, smartphone technology has been developing rapidly. The smartphone not only has excellent image acquisition ability, but also has the considerable computational processing ability. In addition, the gyroscope and positioning function on the smartphone will also help to measure the structure of the canopy. In this paper, we present a smartphone based hemispherical photography system. The system consists of smart phones, low-cost fisheye lenses and PMMA adapters. We designed an Android based App to obtain the canopy hemisphere images through low-cost fisheye lenses and provide horizontal collimation information. In addition, the App will add the acquisition location tag obtained by GPS and auxiliary positioning method in hemisphere image information after the canopy structure hemisphere image acquisition. The system was tested in the urban forest after it was completed. The test results show that the smartphone based hemispherical photography system can effectively collect the high-resolution canopy structure image of the plant.

Doing the hard work where it's easiest? Examining the relationships between urban greening programs and social and ecological characteristics

Treesearch

Dexter H. Locke; J. Morgan Grove

2016-01-01

In this paper we examine the performance of formal programs associated with tree plantings in Washington, D.C. and Baltimore, MD to understand the relationships between the implementation of urban greening programs and the social and ecological characteristics of a city. Previous research has examined variations in patterns of existing and possible tree canopy cover...

Houston’s Urban Forest, 2015

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Christopher B. Edgar; Gretchen Riley; Dudley R. Hartel; Kerry J. Dooley; Sharon M. Stanton; Mark A. Hatfield; Thomas J. Brandeis; Tonya W. Lister

2017-01-01

An analysis of the urban forest in Houston, Texas, reveals that this area has an estimated 33.3 million live trees with tree canopy that covers 18.4 percent of the city. Roughly 19.2 million of the city’s trees are located on private lands. The most common tree species are yaupon, Chinese tallowtree, Chinese privet, Japanese privet, and sugarberry. Trees in Houston...

Modeling the formation and aging of secondary organic aerosols in Los Angeles during CalNex 2010

DOE PAGES

Hayes, P. L.; Carlton, A. G.; Baker, K. R.; ...

2015-05-26

Four different literature parameterizations for the formation and evolution of urban secondary organic aerosol (SOA) frequently used in 3-D models are evaluated using a 0-D box model representing the Los Angeles metropolitan region during the California Research at the Nexus of Air Quality and Climate Change (CalNex) 2010 campaign. We constrain the model predictions with measurements from several platforms and compare predictions with particle- and gas-phase observations from the CalNex Pasadena ground site. That site provides a unique opportunity to study aerosol formation close to anthropogenic emission sources with limited recirculation. The model SOA that formed only from the oxidationmore » of VOCs (V-SOA) is insufficient to explain the observed SOA concentrations, even when using SOA parameterizations with multi-generation oxidation that produce much higher yields than have been observed in chamber experiments, or when increasing yields to their upper limit estimates accounting for recently reported losses of vapors to chamber walls. The Community Multiscale Air Quality (WRF-CMAQ) model (version 5.0.1) provides excellent predictions of secondary inorganic particle species but underestimates the observed SOA mass by a factor of 25 when an older VOC-only parameterization is used, which is consistent with many previous model–measurement comparisons for pre-2007 anthropogenic SOA modules in urban areas. Including SOA from primary semi-volatile and intermediate-volatility organic compounds (P-S/IVOCs) following the parameterizations of Robinson et al. (2007), Grieshop et al. (2009), or Pye and Seinfeld (2010) improves model–measurement agreement for mass concentration. The results from the three parameterizations show large differences (e.g., a factor of 3 in SOA mass) and are not well constrained, underscoring the current uncertainties in this area. Our results strongly suggest that other precursors besides VOCs, such as P-S/IVOCs, are needed to explain the observed SOA concentrations in Pasadena. All the recent parameterizations overpredict urban SOA formation at long photochemical ages (≈ 3 days) compared to observations from multiple sites, which can lead to problems in regional and especially global modeling. However, reducing IVOC emissions by one-half in the model to better match recent IVOC measurements improves SOA predictions at these long photochemical ages. Among the explicitly modeled VOCs, the precursor compounds that contribute the greatest SOA mass are methylbenzenes. Measured polycyclic aromatic hydrocarbons (naphthalenes) contribute 0.7% of the modeled SOA mass. The amounts of SOA mass from diesel vehicles, gasoline vehicles, and cooking emissions are estimated to be 16–27, 35–61, and 19–35%, respectively, depending on the parameterization used, which is consistent with the observed fossil fraction of urban SOA, 71(±3) %. The relative contribution of each source is uncertain by almost a factor of 2 depending on the parameterization used. In-basin biogenic VOCs are predicted to contribute only a few percent to SOA. A regional SOA background of approximately 2.1 μg m −3 is also present due to the long-distance transport of highly aged OA, likely with a substantial contribution from regional biogenic SOA. The percentage of SOA from diesel vehicle emissions is the same, within the estimated uncertainty, as reported in previous work that analyzed the weekly cycles in OA concentrations (Bahreini et al., 2012; Hayes et al., 2013). However, the modeling work presented here suggests a strong anthropogenic source of modern carbon in SOA, due to cooking emissions, which was not accounted for in those previous studies and which is higher on weekends. Lastly, this work adapts a simple two-parameter model to predict SOA concentration and O/C from urban emissions. This model successfully predicts SOA concentration, and the optimal parameter combination is very similar to that found for Mexico City. This approach provides a computationally inexpensive method for predicting urban SOA in global and climate models. We estimate pollution SOA to account for 26 Tg yr −1 of SOA globally, or 17% of global SOA, one-third of which is likely to be non-fossil.« less

Modeling the formation and aging of secondary organic aerosols in Los Angeles during CalNex 2010

NASA Astrophysics Data System (ADS)

Hayes, P. L.; Carlton, A. G.; Baker, K. R.; Ahmadov, R.; Washenfelder, R. A.; Alvarez, S.; Rappengluck, B.; Gilman, J. B.; Kuster, W. C.; de Gouw, J. A.; Zotter, P.; Prevot, A. S. H.; Szidat, S.; Kleindienst, T. E.; Offenberg, J. H.; Ma, P. K.; Jimenez, J. L.

2015-05-01

Four different literature parameterizations for the formation and evolution of urban secondary organic aerosol (SOA) frequently used in 3-D models are evaluated using a 0-D box model representing the Los Angeles metropolitan region during the California Research at the Nexus of Air Quality and Climate Change (CalNex) 2010 campaign. We constrain the model predictions with measurements from several platforms and compare predictions with particle- and gas-phase observations from the CalNex Pasadena ground site. That site provides a unique opportunity to study aerosol formation close to anthropogenic emission sources with limited recirculation. The model SOA that formed only from the oxidation of VOCs (V-SOA) is insufficient to explain the observed SOA concentrations, even when using SOA parameterizations with multi-generation oxidation that produce much higher yields than have been observed in chamber experiments, or when increasing yields to their upper limit estimates accounting for recently reported losses of vapors to chamber walls. The Community Multiscale Air Quality (WRF-CMAQ) model (version 5.0.1) provides excellent predictions of secondary inorganic particle species but underestimates the observed SOA mass by a factor of 25 when an older VOC-only parameterization is used, which is consistent with many previous model-measurement comparisons for pre-2007 anthropogenic SOA modules in urban areas. Including SOA from primary semi-volatile and intermediate-volatility organic compounds (P-S/IVOCs) following the parameterizations of Robinson et al. (2007), Grieshop et al. (2009), or Pye and Seinfeld (2010) improves model-measurement agreement for mass concentration. The results from the three parameterizations show large differences (e.g., a factor of 3 in SOA mass) and are not well constrained, underscoring the current uncertainties in this area. Our results strongly suggest that other precursors besides VOCs, such as P-S/IVOCs, are needed to explain the observed SOA concentrations in Pasadena. All the recent parameterizations overpredict urban SOA formation at long photochemical ages (~ 3 days) compared to observations from multiple sites, which can lead to problems in regional and especially global modeling. However, reducing IVOC emissions by one-half in the model to better match recent IVOC measurements improves SOA predictions at these long photochemical ages. Among the explicitly modeled VOCs, the precursor compounds that contribute the greatest SOA mass are methylbenzenes. Measured polycyclic aromatic hydrocarbons (naphthalenes) contribute 0.7% of the modeled SOA mass. The amounts of SOA mass from diesel vehicles, gasoline vehicles, and cooking emissions are estimated to be 16-27, 35-61, and 19-35%, respectively, depending on the parameterization used, which is consistent with the observed fossil fraction of urban SOA, 71(±3) %. The relative contribution of each source is uncertain by almost a factor of 2 depending on the parameterization used. In-basin biogenic VOCs are predicted to contribute only a few percent to SOA. A regional SOA background of approximately 2.1 μg m-3 is also present due to the long-distance transport of highly aged OA, likely with a substantial contribution from regional biogenic SOA. The percentage of SOA from diesel vehicle emissions is the same, within the estimated uncertainty, as reported in previous work that analyzed the weekly cycles in OA concentrations (Bahreini et al., 2012; Hayes et al., 2013). However, the modeling work presented here suggests a strong anthropogenic source of modern carbon in SOA, due to cooking emissions, which was not accounted for in those previous studies and which is higher on weekends. Lastly, this work adapts a simple two-parameter model to predict SOA concentration and O/C from urban emissions. This model successfully predicts SOA concentration, and the optimal parameter combination is very similar to that found for Mexico City. This approach provides a computationally inexpensive method for predicting urban SOA in global and climate models. We estimate pollution SOA to account for 26 Tg yr-1 of SOA globally, or 17% of global SOA, one-third of which is likely to be non-fossil.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayes, P. L.; Carlton, A. G.; Baker, K. R.

Four different literature parameterizations for the formation and evolution of urban secondary organic aerosol (SOA) frequently used in 3-D models are evaluated using a 0-D box model representing the Los Angeles metropolitan region during the California Research at the Nexus of Air Quality and Climate Change (CalNex) 2010 campaign. We constrain the model predictions with measurements from several platforms and compare predictions with particle- and gas-phase observations from the CalNex Pasadena ground site. That site provides a unique opportunity to study aerosol formation close to anthropogenic emission sources with limited recirculation. The model SOA that formed only from the oxidationmore » of VOCs (V-SOA) is insufficient to explain the observed SOA concentrations, even when using SOA parameterizations with multi-generation oxidation that produce much higher yields than have been observed in chamber experiments, or when increasing yields to their upper limit estimates accounting for recently reported losses of vapors to chamber walls. The Community Multiscale Air Quality (WRF-CMAQ) model (version 5.0.1) provides excellent predictions of secondary inorganic particle species but underestimates the observed SOA mass by a factor of 25 when an older VOC-only parameterization is used, which is consistent with many previous model–measurement comparisons for pre-2007 anthropogenic SOA modules in urban areas. Including SOA from primary semi-volatile and intermediate-volatility organic compounds (P-S/IVOCs) following the parameterizations of Robinson et al. (2007), Grieshop et al. (2009), or Pye and Seinfeld (2010) improves model–measurement agreement for mass concentration. The results from the three parameterizations show large differences (e.g., a factor of 3 in SOA mass) and are not well constrained, underscoring the current uncertainties in this area. Our results strongly suggest that other precursors besides VOCs, such as P-S/IVOCs, are needed to explain the observed SOA concentrations in Pasadena. All the recent parameterizations overpredict urban SOA formation at long photochemical ages (≈ 3 days) compared to observations from multiple sites, which can lead to problems in regional and especially global modeling. However, reducing IVOC emissions by one-half in the model to better match recent IVOC measurements improves SOA predictions at these long photochemical ages. Among the explicitly modeled VOCs, the precursor compounds that contribute the greatest SOA mass are methylbenzenes. Measured polycyclic aromatic hydrocarbons (naphthalenes) contribute 0.7% of the modeled SOA mass. The amounts of SOA mass from diesel vehicles, gasoline vehicles, and cooking emissions are estimated to be 16–27, 35–61, and 19–35%, respectively, depending on the parameterization used, which is consistent with the observed fossil fraction of urban SOA, 71(±3) %. The relative contribution of each source is uncertain by almost a factor of 2 depending on the parameterization used. In-basin biogenic VOCs are predicted to contribute only a few percent to SOA. A regional SOA background of approximately 2.1 μg m −3 is also present due to the long-distance transport of highly aged OA, likely with a substantial contribution from regional biogenic SOA. The percentage of SOA from diesel vehicle emissions is the same, within the estimated uncertainty, as reported in previous work that analyzed the weekly cycles in OA concentrations (Bahreini et al., 2012; Hayes et al., 2013). However, the modeling work presented here suggests a strong anthropogenic source of modern carbon in SOA, due to cooking emissions, which was not accounted for in those previous studies and which is higher on weekends. Lastly, this work adapts a simple two-parameter model to predict SOA concentration and O/C from urban emissions. This model successfully predicts SOA concentration, and the optimal parameter combination is very similar to that found for Mexico City. This approach provides a computationally inexpensive method for predicting urban SOA in global and climate models. We estimate pollution SOA to account for 26 Tg yr −1 of SOA globally, or 17% of global SOA, one-third of which is likely to be non-fossil.« less

Comparison of Tillandsia usneoides (Spanish moss) water and leachate dynamics between urban and pristine barrier island maritime oak forests

NASA Astrophysics Data System (ADS)

Van Stan, J. T.; Stubbins, A.; Reichard, J. S.; Wright, K.; Jenkins, R. B.

2013-12-01

Epiphyte coverage on forest canopies can drastically alter the volume and chemical composition of rainwater reaching soils. Along subtropical and tropical coastlines Tillandisa usneoides L. (Spanish moss), in particular, can envelop urban and natural tree crowns. Several cities actively manage their 'moss' covered forest to enhance aesthetics in the most active tourist areas (e.g., Savannah GA, St. Augustine FL, Charleston SC). Since T. usneoides survives through atmospheric water and solute exchange from specialized trichomes (scales), we hypothesized that T. usneoides water storage dynamics and leachate chemistry may be altered by exposure to this active urban atmosphere. 30 samples of T. usneoides from managed forests around the tourist center of Savannah, Georgia, USA were collected to compare with 30 samples from the pristine maritime live oak (Quercus virginiana Mill.) forests of a nearby undeveloped barrier island (St. Catherines Island, Georgia, USA). Maximum water storage capacities were determined via submersion (for all 60 samples) along with dissolved ion (DI) and organic matter (DOM) concentrations (for 15 samples each) after simulated throughfall generation using milliQ ultrapurified water. Further, DOM quality was evaluated (for 15 samples each) using absorbance and fluorescence spectroscopy (EEMS). Results show significant alterations to water storage dynamics, DI, DOM, and DOM quality metrics under urban atmospheric conditions, suggesting modified C and water cycling in urban forest canopies that may, in turn, influence intrasystem nutrient cycles in urban catchment soils or streams via runoff.

Modeling climate change, urbanization, and fire effects on Pinus palustris ecosystems of the southeastern U.S.

USGS Publications Warehouse

Costanza, Jennifer; Terando, Adam J.; McKerrow, Alexa; Collazo, Jaime A.

2015-01-01

Managing ecosystems for resilience and sustainability requires understanding how they will respond to future anthropogenic drivers such as climate change and urbanization. In fire-dependent ecosystems, predicting this response requires a focus on how these drivers will impact fire regimes. Here, we use scenarios of climate change, urbanization and management to simulate the future dynamics of the critically endangered and fire-dependent longleaf pine (Pinus palustris) ecosystem. We investigated how climate change and urbanization will affect the ecosystem, and whether the two conservation goals of a 135% increase in total longleaf area and a doubling of fire-maintained open-canopy habitat can be achieved in the face of these drivers. Our results show that while climatic warming had little effect on the wildfire regime, and thus on longleaf pine dynamics, urban growth led to an 8% reduction in annual wildfire area. The management scenarios we tested increase the ecosystem's total extent by up to 62% and result in expansion of open-canopy longleaf by as much as 216%, meeting one of the two conservation goals for the ecosystem. We find that both conservation goals for this ecosystem, which is climate-resilient but vulnerable to urbanization, are only attainable if a greater focus is placed on restoration of non-longleaf areas as opposed to maintaining existing longleaf stands. Our approach demonstrates the importance of accounting for multiple relevant anthropogenic threats in an ecosystem-specific context in order to facilitate more effective management actions.

Invasive Shrub Mapping in an Urban Environment from Hyperspectral and LiDAR-Derived Attributes.

PubMed

Chance, Curtis M; Coops, Nicholas C; Plowright, Andrew A; Tooke, Thoreau R; Christen, Andreas; Aven, Neal

2016-01-01

Proactive management of invasive species in urban areas is critical to restricting their overall distribution. The objective of this work is to determine whether advanced remote sensing technologies can help to detect invasions effectively and efficiently in complex urban ecosystems such as parks. In Surrey, BC, Canada, Himalayan blackberry ( Rubus armeniacus ) and English ivy ( Hedera helix ) are two invasive shrub species that can negatively affect native ecosystems in cities and managed urban parks. Random forest (RF) models were created to detect these two species using a combination of hyperspectral imagery, and light detection and ranging (LiDAR) data. LiDAR-derived predictor variables included irradiance models, canopy structural characteristics, and orographic variables. RF detection accuracy ranged from 77.8 to 87.8% for Himalayan blackberry and 81.9 to 82.1% for English ivy, with open areas classified more accurately than areas under canopy cover. English ivy was predicted to occur across a greater area than Himalayan blackberry both within parks and across the entire city. Both Himalayan blackberry and English ivy were mostly located in clusters according to a Local Moran's I analysis. The occurrence of both species decreased as the distance from roads increased. This study shows the feasibility of producing highly accurate detection maps of plant invasions in urban environments using a fusion of remotely sensed data, as well as the ability to use these products to guide management decisions.

The model SIRANE for atmospheric urban pollutant dispersion; part I, presentation of the model

NASA Astrophysics Data System (ADS)

Soulhac, Lionel; Salizzoni, Pietro; Cierco, F.-X.; Perkins, Richard

2011-12-01

In order to control and manage urban air quality, public authorities require an integrated approach that incorporates direct measurements and modelling of mean pollutant concentrations. These have to be performed by means of operational modelling tools, that simulate the transport of pollutants within and above the urban canopy over a large number of streets. The operational models must be able to assess rapidly a large variety of situations and with limited computing resources. SIRANE is an operational urban dispersion model based on a simplified description of the urban geometry that adopts parametric relations for the pollutant transfer phenomena within and out of the urban canopy. The streets in a city district are modelled as a network of connected street segments. The flow within each street is driven by the component of the external wind parallel to the street, and the pollutant is assumed to be uniformly mixed within the street. The model contains three main mechanisms for transport in and out of a street: advection along the street axis, diffusion across the interface between the street and the overlying air flow and exchanges with other streets at street intersections. The dispersion of pollutants advected or diffused out of the streets is taken into account using a Gaussian plume model, with the standard deviations σ y and σ z parameterised by the similarity theory. The input data for the final model are the urban geometry, the meteorological parameters, the background concentration of pollutants advected into the model domain by the wind and the emissions within each street in the network.

Advances in understanding, models and parameterizations of biosphere-atmosphere ammonia exchange

NASA Astrophysics Data System (ADS)

Flechard, C. R.; Massad, R.-S.; Loubet, B.; Personne, E.; Simpson, D.; Bash, J. O.; Cooter, E. J.; Nemitz, E.; Sutton, M. A.

2013-07-01

Atmospheric ammonia (NH3) dominates global emissions of total reactive nitrogen (Nr), while emissions from agricultural production systems contribute about two-thirds of global NH3 emissions; the remaining third emanates from oceans, natural vegetation, humans, wild animals and biomass burning. On land, NH3 emitted from the various sources eventually returns to the biosphere by dry deposition to sink areas, predominantly semi-natural vegetation, and by wet and dry deposition as ammonium (NH4+) to all surfaces. However, the land/atmosphere exchange of gaseous NH3 is in fact bi-directional over unfertilized as well as fertilized ecosystems, with periods and areas of emission and deposition alternating in time (diurnal, seasonal) and space (patchwork landscapes). The exchange is controlled by a range of environmental factors, including meteorology, surface layer turbulence, thermodynamics, air and surface heterogeneous-phase chemistry, canopy geometry, plant development stage, leaf age, organic matter decomposition, soil microbial turnover, and, in agricultural systems, by fertilizer application rate, fertilizer type, soil type, crop type, and agricultural management practices. We review the range of processes controlling NH3 emission and uptake in the different parts of the soil-canopy-atmosphere continuum, with NH3 emission potentials defined at the substrate and leaf levels by different [NH4+] / [H+] ratios (Γ). Surface/atmosphere exchange models for NH3 are necessary to compute the temporal and spatial patterns of emissions and deposition at the soil, plant, field, landscape, regional and global scales, in order to assess the multiple environmental impacts of airborne and deposited NH3 and NH4+. Models of soil/vegetation/atmosphere NH3 exchange are reviewed from the substrate and leaf scales to the global scale. They range from simple steady-state, "big leaf" canopy resistance models, to dynamic, multi-layer, multi-process, multi-chemical species schemes. Their level of complexity depends on their purpose, the spatial scale at which they are applied, the current level of parameterization, and the availability of the input data they require. State-of-the-art solutions for determining the emission/sink Γ potentials through the soil/canopy system include coupled, interactive chemical transport models (CTM) and soil/ecosystem modelling at the regional scale. However, it remains a matter for debate to what extent realistic options for future regional and global models should be based on process-based mechanistic versus empirical and regression-type models. Further discussion is needed on the extent and timescale by which new approaches can be used, such as integration with ecosystem models and satellite observations.

Separating foliar physiology from morphology reveals the relative roles of vertically structured transpiration factors within red maple crowns and limitations of larger scale models

PubMed Central

Bauerle, William L.; Bowden, Joseph D.

2011-01-01

A spatially explicit mechanistic model, MAESTRA, was used to separate key parameters affecting transpiration to provide insights into the most influential parameters for accurate predictions of within-crown and within-canopy transpiration. Once validated among Acer rubrum L. genotypes, model responses to different parameterization scenarios were scaled up to stand transpiration (expressed per unit leaf area) to assess how transpiration might be affected by the spatial distribution of foliage properties. For example, when physiological differences were accounted for, differences in leaf width among A. rubrum L. genotypes resulted in a 25% difference in transpiration. An in silico within-canopy sensitivity analysis was conducted over the range of genotype parameter variation observed and under different climate forcing conditions. The analysis revealed that seven of 16 leaf traits had a ≥5% impact on transpiration predictions. Under sparse foliage conditions, comparisons of the present findings with previous studies were in agreement that parameters such as the maximum Rubisco-limited rate of photosynthesis can explain ∼20% of the variability in predicted transpiration. However, the spatial analysis shows how such parameters can decrease or change in importance below the uppermost canopy layer. Alternatively, model sensitivity to leaf width and minimum stomatal conductance was continuous along a vertical canopy depth profile. Foremost, transpiration sensitivity to an observed range of morphological and physiological parameters is examined and the spatial sensitivity of transpiration model predictions to vertical variations in microclimate and foliage density is identified to reduce the uncertainty of current transpiration predictions. PMID:21617246

Effect of wakes on land-atmosphere fluxes

NASA Astrophysics Data System (ADS)

Markfort, C. D.; Zhang, W.; Porte-Agel, F.; Stefan, H. G.

2011-12-01

Wakes affect land-atmosphere fluxes of momentum and scalars, including water vapor and trace gases. Canopies and bluff bodies, including forests, buildings and topography, cause boundary layer flow separation, significantly extend flow recovery, and lead to a break down of standard Monin-Obukhov similarity relationships in the atmospheric boundary layer (ABL). Wakes generated by these land surface features persist for significant distances affecting a large fraction of the Earth's terrestrial surface. This effect is currently not accounted for in land-atmosphere modeling, and little is known about how heterogeneity of wake-generating features effect land surface fluxes. Additionally flux measurements, made in wake-affected regions, do not satisfy the homogeneous requirements for the standard eddy correlation (EC) method. This phenomenon often referred to as sheltering has been shown to affect momentum and kinetic energy fluxes into lakes from the atmosphere (Markfort et al. 2010). This presentation will highlight results from controlled wind tunnel experiments of neutral and thermally stratified boundary layers, using PIV and custom x-wire/cold-wire anemometry, designed to understand how the physical structure of upstream bluff bodies or porous canopies and thermal stability affect the separation zone, boundary layer recovery and surface fluxes. We also compare these results to field measurements taken with a Doppler LiDAR in the wake of a canopy and a building. We have found that there is a nonlinear relationship between porosity and flow separation behind a canopy to clearing transition. Results will provide the basis for new parameterizations to account for wake effects on land-atmosphere fluxes and corrections for EC measurements over open fields, lakes, and wetlands.

A new empirical model to estimate hourly diffuse photosynthetic photon flux density

NASA Astrophysics Data System (ADS)

Foyo-Moreno, I.; Alados, I.; Alados-Arboledas, L.

2018-05-01

Knowledge of the photosynthetic photon flux density (Qp) is critical in different applications dealing with climate change, plant physiology, biomass production, and natural illumination in greenhouses. This is particularly true regarding its diffuse component (Qpd), which can enhance canopy light-use efficiency and thereby boost carbon uptake. Therefore, diffuse photosynthetic photon flux density is a key driving factor of ecosystem-productivity models. In this work, we propose a model to estimate this component, using a previous model to calculate Qp and furthermore divide it into its components. We have used measurements in urban Granada (southern Spain), of global solar radiation (Rs) to study relationships between the ratio Qpd/Rs with different parameters accounting for solar position, water-vapour absorption and sky conditions. The model performance has been validated with experimental measurements from sites having varied climatic conditions. The model provides acceptable results, with the mean bias error and root mean square error varying between - 0.3 and - 8.8% and between 9.6 and 20.4%, respectively. Direct measurements of this flux are very scarce so that modelling simulations are needed, this is particularly true regarding its diffuse component. We propose a new parameterization to estimate this component using only measured data of solar global irradiance, which facilitates its use for the construction of long-term data series of PAR in regions where continuous measurements of PAR are not yet performed.

Approximating Reflectance and Transmittance of Vegetation Using Multiple Spectral Invariants

NASA Astrophysics Data System (ADS)

Mottus, M.

2011-12-01

Canopy spectral invariants, eigenvalues of the radiative transfer equation and photon recollision probability are some of the new theoretical tools that have been applied in remote sensing of vegetation and atmosphere. The theoretical approach based on spectral invariants, informally also referred to as the p-theory, owns its attractivity to several factors. Firstly, it provides a rapid and physically-based way of describing canopy scattering. Secondly, the p-theory aims at parameterizing canopy structure in reflectance models using a simple and intuitive concept which can be applied at various structural levels, from shoot to tree crown. The theory has already been applied at scales from the molecular level to forest stands. The most important shortcoming of the p-theory lies in its inability to predict the directionality of scattering. The theory is currently based on only one physical parameter, the photon recollision probability p. It is evident that one parameter cannot contain enough information to reasonably predict the observed complex reflectance patterns produced by natural vegetation canopies. Without estimating scattering directionality, however, the theory cannot be compared with even the most simple (and well-tested) two-stream vegetation reflectance models. In this study, we evaluate the possibility to use additional parameters to fit the measured reflectance and transmittance of a vegetation stand. As a first step, the parameters are applied to separate canopy scattering into reflectance and transmittance. New parameters are introduced following the general approach of eigenvector expansion. Thus, the new parameters are coined higher-order spectral invariants. Calculation of higher-order invariants is based on separating first-order scattering from total scattering. Thus, the method explicitly accounts for different view geometries with different fractions of visible sunlit canopy (e.g., hot-spot). It additionally allows to produce different irradiation levels on leaf surfaces for direct and diffuse incidence, thus (in theory) allowing more accurate calculation of potential photosynthesis rates. Similarly to the p-theory, the use of multiple spectral invariants facilitates easy parametrization of canopy structure and scaling between different structural levels (leaf-shoot-stand). Spectral invariant-based remote sensing approaches are well suited for relatively large pixels even when no detailed ground truth information is available. In a case study, the theory of multiple spectral invariants was applied to measured canopy scattering. Spectral reflectance and transmittance measurements were carried out in gray alder (Alnus incana) plantation at Tartu Observatory, Estonia, in August 2006. The equations produced by the theory of spectral invariants were fitted to measured radiation fluxes. Preliminary results indicate that quantities with invariant-like behavior may indeed be used to approximate canopy scattering directionality.

Age-related effects on leaf area/sapwood area relationships, canopy transpiration and carbon gain of Norway spruce stands (Picea abies) in the Fichtelgebirge, Germany.

PubMed

Köstner, B; Falge, E; Tenhunen, J D

2002-06-01

Stand age is an important structural determinant of canopy transpiration (E(c)) and carbon gain. Another more functional parameter of forest structure is the leaf area/sapwood area relationship, A(L)/A(S), which changes with site conditions and has been used to estimate leaf area index of forest canopies. The interpretation of age-related changes in A(L)/A(S) and the question of how A(L)/A(S) is related to forest functions are of current interest because they may help to explain forest canopy fluxes and growth. We conducted studies in mature stands of Picea abies (L.) Karst. varying in age from 40 to 140 years, in tree density from 1680 to 320 trees ha(-1), and in tree height from 15 to 30 m. Structural parameters were measured by biomass harvests of individual trees and stand biometry. We estimated E(c) from scaled-up xylem sap flux of trees, and canopy-level fluxes were predicted by a three-dimensional microclimate and gas exchange model (STANDFLUX). In contrast to pine species, A(L)/A(S) of P. abies increased with stand age from 0.26 to 0.48 m(2) cm(-2). Agreement between E(c) derived from scaled-up sap flux and modeled canopy transpiration was obtained with the same parameterization of needle physiology independent of stand age. Reduced light interception per leaf area and, as a consequence, reductions in net canopy photosynthesis (A(c)), canopy conductance (g(c)) and E(c) were predicted by the model in the older stands. Seasonal water-use efficiency (WUE = A(c)/E(c)), derived from scaled-up sap flux and stem growth as well as from model simulation, declined with increasing A(L)/A(S) and stand age. Based on the different behavior of age-related A(L)/A(S) in Norway spruce stands compared with other tree species, we conclude that WUE rather than A(L)/A(S) could represent a common age-related property of all species. We also conclude that, in addition to hydraulic limitations reducing carbon gain in old stands, a functional change in A(L)/A(S) that is related to reduced light interception per leaf area provides another potential explanation for reduced carbon gain in old stands of P. abies, even when hydraulic constraints increase in response to changes in canopy architecture and aging.

Estimating Carbon Storage and Sequestration by Urban Trees at Multiple Spatial Resolutions

NASA Astrophysics Data System (ADS)

Wu, J.; Tran, A.; Liao, A.

2010-12-01

Urban forests are an important component of urban-suburban environments. Urban trees provide not only a full range of social and psychological benefits to city dwellers, but also valuable ecosystem services to communities, such as removing atmospheric carbon dioxide, improving air quality, and reducing storm water runoff. There is an urgent need for developing strategic conservation plans for environmentally sustainable urban-suburban development based on the scientific understanding of the extent and function of urban forests. However, several challenges remain to accurately quantify various environmental benefits provided by urban trees, among which is to deal with the effect of changing spatial resolution and/or scale. In this study, we intended to examine the uncertainties of carbon storage and sequestration associated with the tree canopy coverage of different spatial resolutions. Multi-source satellite imagery data were acquired for the City of Fullerton, located in Orange County of California. The tree canopy coverage of the study area was classified at three spatial resolutions, ranging from 30 m (Landsat-5 Thematic Mapper), 15 m (Advanced Spaceborne Thermal Emission and Reflection Radiometer), to 2.5 m (QuickBird). We calculated the amount of carbon stored in the trees represented on the individual tree coverage maps and the annual carbon taken up by the trees with a model (i.e., CITYgreen) developed by the U.S. Forest Service. The results indicate that urban trees account for significant proportions of land cover in the study area even with the low spatial resolution data. The estimated carbon fixation benefits vary greatly depending on the details of land use and land cover classification. The extrapolation of estimation from the fine-resolution stand-level to the low-resolution landscape-scale will likely not preserve reasonable accuracy.

The Detection and Characterization of Urbanization, Industrialization, and Longwall Mining Impacts on Forest Ecosystems Through the Use of GiS and Remote Sensing Techniques

NASA Astrophysics Data System (ADS)

Pfeil-McCullough, Erin Kathleen

Urbanization has far reaching and significant effects on forest ecosystems, directly through urban development and indirectly through supportive processes such as coal mining and agriculture. Urban processes modify the landscape leading to altered hillslope hydrology, increased disturbance, and the introduction of non-native forest pathogens. This dissertation addresses several challenges in our ability to detect these urbanization impacts on forests via geospatial analyses. The role of forests in urban hydrological processes has been extensively studied, but the impacts of urbanized hydrology on forests remain poorly examined. This dissertation documented impacts to hydrology and forests at variety of temporal and spatial scales: 1) A geospatial comparison of the historic and contemporary forests of Allegheny County, Pennsylvania revealed substantial shifts in tree species, but less change in the species soil moisture preference. These results document additional evidence that increased heterogeneity in urban soil moisture alters forest structure. 2) To examine soil moisture changes, impacts of longwall mine subsidence were assessed by using a Landsat based canopy moisture index and hot spot analysis tools at the forest patch scale. Declines in forest canopy moisture were detected over longwall mines as mining progressed through time, and results contradicted assumptions that the hydrological impacts overlying LMS recover within 4-5 years following subsidence of undermined land. 3) Utilizing a landslide susceptibility model (SINMAP), increases in landslide susceptibility were predicted in Pittsburgh, PA based on several scenarios of ash tree loss to the emerald ash borer (EAB), a bark beetle that rapidly kills ash trees. This model provides a tool to predict changes in landslide susceptibility following tree loss, increasing the understanding of urban forest function and its role in slope stability. Detecting how urbanized hydrology impacts forest health, function, and development is fundamental to sustaining the services forests provide. Results from this dissertation will ultimately allow improvements in the management and protection of both trees and water resources in urban systems and beyond.

Multiple health benefits of urban tree canopy: The mounting evidence for a green prescription

Treesearch

Jared M. Ulmer; Kathleen L. Wolf; Desiree R. Backman; Raymond L. Tretheway; Cynthia JA Blain; Jarlath PM O’Neil-Dunne; Lawrence D. Frank

2016-01-01

The purpose of this study was to enhance the understanding of the health-promoting potential of trees in an urbanized region of the United States. This was done using high-resolution LiDAR and imagery data to quantify tree cover within 250 m of the residence of 7910 adult participants in the California Health Interview Survey, then testing for main and mediating...

Assessing urban forest effects and values, Los Angeles' urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Lorraine Weller; Antonio Davila

2011-01-01

An analysis of trees in Los Angeles, CA, reveals that this area has about 6 million trees with tree and shrub canopies that cover 24.9 percent of the city. The most common tree species are Italian cypress, scrub oak, laurel sumac, Mexican fan palm, and Indian laurel, Trees in Los Angeles currently store about 1.3 million tons of carbon (4.7 million tons CO2...

Strategic tree planting as an EPA encouraged pollutant reduction strategy: how urban trees can obtain credit in state implementation plans

Treesearch

Dr. David J. Nowak

2005-01-01

As tree programs are new to the SIP process, "to facilitate Federal approval of an emerging or voluntary measure States are encouraged to work with their EPA regional ofice during the development process". Programs to increase canopy cover in urban areas can achieve many benefits. They can help improve air and water quality, as well as other factors related...

Contributions to urban heat island on the local neighborhood scale

NASA Astrophysics Data System (ADS)

Hertel, Daniel; Schlink, Uwe

2017-04-01

Already today around half of the global population is living in urban regions and recent studies expect a further increase until mid-21st century. Therefore, especially in the context of climate change, an increasing amount of urban inhabitants are affected by urban climate and air quality. One special characteristic of urban climate is the urban heat island (UHI) effect, where urbanized regions are warmer than the rural surroundings. With respect to climate change and the growing urbanization it is obvious that the UHI effect will tend to be intensified. To keep our cities worth living, it is necessary to think about adaptation and mitigation strategies which refer to both, climate protection as well as utilization of chances resulting from climate changes. One step to a more precisely adaptation, particularly on the neighborhood scale, is an improved understanding of the magnitude of bio geophysical processes (e.g.: radiation balance, convection efficiency, evapotranspiration, storage heat, anthropogenic heat etc.), which contribute to the urban warming. Considering that UHI can be expressed as temperature difference ΔT between urban and rural areas, we can interpret these processes as how they would change temperature, because of energy redistribution, from a rural area to an urbanized region. Up to now on the local scale there is a knowledge gap about these processes. The mentioned processes are parts of a surface energy balance (based on the work of Zhao et al., 2014). That means they refer to the surface UHI effect and not to the canopy layer UHI effect. Assuming that the urban region is a volume with the top at the height of the canopy layer, we can approximately identify the surface UHI effect as the canopy layer UHI effect since the information comes from both the surface and the atmosphere inside. This assumption is not valid for Zhao's approach because they analyzed whole cities and could neglect such processes within the volume. This contribution presents first results from my PhD project where I take micrometeorological simulations for a case study site ("Bayerischer Bahnhof" in Leipzig; Saxony, Germany; 51°20', 12°22') from the ENVI-met model and calculate the UHI as well as the contributing bio geophysical processes. The results are maps of the processes that directly quantify their contribution to the total UHI at each point in the area. The benefits of this approach can be seen in the small resolution (3x3 m) of the simulation area which gives further insights into local UHI variances. Also, the effects of restructuring within quarters and methods to avoid adverse health impacts on the residents can be developed in a more precisely and sophisticated way. Zhao, L., Lee, X., Smith, R.B., Oleson, K., (2014): Strong contributions of local background climate to urban heat islands. Nature 511: 216-219, doi: 10.1038/nature13462

Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China, during the 2014 APEC summit

NASA Astrophysics Data System (ADS)

Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

2015-11-01

The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the Beijing 325 m meteorological tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition near ground level using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3- / SO42- mass ratios illustrates an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed of secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors. In addition to emission controls, the routine circulations of mountain-valley breezes were also found to play an important role in alleviating PM levels and achieving the "APEC blue" effect. The evolution of vertical differences between 260 m and the ground level was also investigated. Our results show complex vertical differences during the formation and evolution of severe haze episodes that are closely related to aerosol sources and boundary-layer dynamics.

Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China during 2014 APEC summit

NASA Astrophysics Data System (ADS)

Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

2015-08-01

The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the 325 m Beijing Meteorological Tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition at near ground level using a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3-/SO42- mass ratios illustrate an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed by secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors such as SO2, NOx, and volatile organic compounds (VOCs). In addition to emission controls, the routine circulations of mountain-valley breezes were also found to play an important role in alleviating PM levels and achieving the "APEC blue" effect. The evolution of vertical differences between 260 m and the ground level was also investigated. Our results show complex vertical differences during the formation and evolution of severe haze episodes that are closely related to aerosol sources and boundary layer dynamics.

Adjustment of Turbulent Boundary-Layer Flow to Idealized Urban Surfaces: A Large-Eddy Simulation Study

NASA Astrophysics Data System (ADS)

Cheng, Wai-Chi; Porté-Agel, Fernando

2015-05-01

Large-eddy simulations (LES) are performed to simulate the atmospheric boundary-layer (ABL) flow through idealized urban canopies represented by uniform arrays of cubes in order to better understand atmospheric flow over rural-to-urban surface transitions. The LES framework is first validated with wind-tunnel experimental data. Good agreement between the simulation results and the experimental data are found for the vertical and spanwise profiles of the mean velocities and velocity standard deviations at different streamwise locations. Next, the model is used to simulate ABL flows over surface transitions from a flat homogeneous terrain to aligned and staggered arrays of cubes with height . For both configurations, five different frontal area densities , equal to 0.028, 0.063, 0.111, 0.174 and 0.250, are considered. Within the arrays, the flow is found to adjust quickly and shows similar structure to the wake of the cubes after the second row of cubes. An internal boundary layer is identified above the cube arrays and found to have a similar depth in all different cases. At a downstream location where the flow immediately above the cube array is already adjusted to the surface, the spatially-averaged velocity is found to have a logarithmic profile in the vertical. The values of the displacement height are found to be quite insensitive to the canopy layout (aligned vs. staggered) and increase roughly from to as increases from 0.028 to 0.25. Relatively larger values of the aerodynamic roughness length are obtained for the staggered arrays, compared with the aligned cases, and a maximum value of is found at for both configurations. By explicitly calculating the drag exerted by the cubes on the flow and the drag coefficients of the cubes using our LES results, and comparing the results with existing theoretical expressions, we show that the larger values of for the staggered arrays are related to the relatively larger drag coefficients of the cubes for that configuration compared with the aligned one. The effective mixing length within and above different cube arrays is also calculated and a local maximum of within the canopy is found in all the cases, with values ranging from to . These patterns of are different from those used in existing urban canopy models.

Progress in remote sensing of global land surface heat fluxes and evaporations with a turbulent heat exchange parameterization method

NASA Astrophysics Data System (ADS)

Chen, Xuelong; Su, Bob

2017-04-01

Remote sensing has provided us an opportunity to observe Earth land surface with a much higher resolution than any of GCM simulation. Due to scarcity of information for land surface physical parameters, up-to-date GCMs still have large uncertainties in the coupled land surface process modeling. One critical issue is a large amount of parameters used in their land surface models. Thus remote sensing of land surface spectral information can be used to provide information on these parameters or assimilated to decrease the model uncertainties. Satellite imager could observe the Earth land surface with optical, thermal and microwave bands. Some basic Earth land surface status (land surface temperature, canopy height, canopy leaf area index, soil moisture etc.) has been produced with remote sensing technique, which already help scientists understanding Earth land and atmosphere interaction more precisely. However, there are some challenges when applying remote sensing variables to calculate global land-air heat and water exchange fluxes. Firstly, a global turbulent exchange parameterization scheme needs to be developed and verified, especially for global momentum and heat roughness length calculation with remote sensing information. Secondly, a compromise needs to be innovated to overcome the spatial-temporal gaps in remote sensing variables to make the remote sensing based land surface fluxes applicable for GCM model verification or comparison. A flux network data library (more 200 flux towers) was collected to verify the designed method. Important progress in remote sensing of global land flux and evaporation will be presented and its benefits for GCM models will also be discussed. Some in-situ studies on the Tibetan Plateau and problems of land surface process simulation will also be discussed.

Global parameterization and validation of a two-leaf light use efficiency model for predicting gross primary production across FLUXNET sites: TL-LUE Parameterization and Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Yanlian; Wu, Xiaocui; Ju, Weimin

2016-04-06

Light use efficiency (LUE) models are widely used to simulate gross primary production (GPP). However, the treatment of the plant canopy as a big leaf by these models can introduce large uncertainties in simulated GPP. Recently, a two-leaf light use efficiency (TL-LUE) model was developed to simulate GPP separately for sunlit and shaded leaves and has been shown to outperform the big-leaf MOD17 model at 6 FLUX sites in China. In this study we investigated the performance of the TL-LUE model for a wider range of biomes. For this we optimized the parameters and tested the TL-LUE model using datamore » from 98 FLUXNET sites which are distributed across the globe. The results showed that the TL-LUE model performed in general better than the MOD17 model in simulating 8-day GPP. Optimized maximum light use efficiency of shaded leaves (εmsh) was 2.63 to 4.59 times that of sunlit leaves (εmsu). Generally, the relationships of εmsh and εmsu with εmax were well described by linear equations, indicating the existence of general patterns across biomes. GPP simulated by the TL-LUE model was much less sensitive to biases in the photosynthetically active radiation (PAR) input than the MOD17 model. The results of this study suggest that the proposed TL-LUE model has the potential for simulating regional and global GPP of terrestrial ecosystems and it is more robust with regard to usual biases in input data than existing approaches which neglect the bi-modal within-canopy distribution of PAR.« less

Air quality and human health impacts of grasslands and shrublands in the United States

NASA Astrophysics Data System (ADS)

Gopalakrishnan, Varsha; Hirabayashi, Satoshi; Ziv, Guy; Bakshi, Bhavik R.

2018-06-01

Vegetation including canopy, grasslands, and shrublands can directly sequester pollutants onto the plant surface, resulting in an improvement in air quality. Until now, several studies have estimated the pollution removal capacity of canopy cover at the level of a county, but no such work exists for grasslands and shrublands. This work quantifies the air pollution removal capacity of grasslands and shrublands at the county-level in the United States and estimates the human health benefits associated with pollution removal using the i-Tree Eco model. Sequestration of pollutants is estimated based on the Leaf Area Index (LAI) obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS) derived dataset estimates of LAI and the percentage land cover obtained from the National Land Cover Database (NLCD) for the year 2010. Calculation of pollution removal capacity using local environmental data indicates that grasslands and shrublands remove a total of 6.42 million tonnes of air pollutants in the United States and the associated monetary benefits total 268 million. Human health impacts and associated monetary value due to pollution removal was observed to be significantly high in urban areas indicating that grasslands and shrublands are equally critical as canopy in improving air quality and human health in urban regions.

Sensitivity of Climate Simulations to Land-Surface and Atmospheric Boundary-Layer Treatments-A Review.

NASA Astrophysics Data System (ADS)

Garratt, J. R.

1993-03-01

Aspects of the land-surface and boundary-layer treatments in some 20 or so atmospheric general circulation models (GCMS) are summarized. In only a small fraction of these have significant sensitivity studies been carried out and published. Predominantly, the sensitivity studies focus upon the parameterization of land-surface processes and specification of land-surface properties-the most important of these include albedo, roughness length, soil moisture status, and vegetation density. The impacts of surface albedo and soil moisture upon the climate simulated in GCMs with bare-soil land surfaces are well known. Continental evaporation and precipitation tend to decrease with increased albedo and decreased soil moisture availability. For example, results from numerous studies give an average decrease in continental precipitation of 1 mm day1 in response to an average albedo increase of 0.13. Few conclusive studies have been carried out on the impact of a gross roughness-length change-the primary study included an important statistical assessment of the impact upon the mean July climate around the globe of a decreased continental roughness (by three orders of magnitude). For example, such a decrease reduced the precipitation over Amazonia by 1 to 2 mm day1.The inclusion of a canopy scheme in a GCM ensures the combined impacts of roughness (canopies tend to be rougher than bare soil), albedo (canopies tend to be less reflective than bare soil), and soil-moisture availability (canopies prevent the near-surface soil region from drying out and can access the deep soil moisture) upon the simulated climate. The most revealing studies to date involve the regional impact of Amazonian deforestation. The results of four such studies show that replacing tropical forest with a degraded pasture results in decreased evaporation ( 1 mm day1) and precipitation (1-2 mm day1), and increased near-surface air temperatures (2 K).Sensitivity studies as a whole suggest the need for a realistic surface representation in general circulation models of the atmosphere. It is not yet clear how detailed this representation needs to be, but even allowing for the importance of surface processes, the parameterization of boundary-layer and convective clouds probably represents a greater challenge to improved climate simulations. This is illustrated in the case of surface net radiation for Aniazonia, which is not well simulated and tends to be overestimated, leading to evaporation rates that are too large. Underestimates in cloudiness, cloud albedo, and clear-sky shortwave absorption, rather than in surface albedo, appear to be the main culprits.There are three major tasks that confront the researcher so far as the development and validation of atmospheric boundary-layer (ABL) and surface schemes in GCMs are concerned:(i) There is a need to as' critically the impact of `improved' parameterization schemes on WM simulations, taking into account the problem of natural variability and hence the statistical significance of the induced changes.(ii) There is a need to compare GCM simulations of surface and ABL behavior (particularly regarding the diurnal cycle of surface fluxes, air temperature, and ABL depth) with observations over a range of surface types (vegetation, desert, ocean). In this context, area-average values of surface fluxes will be required to calibrate directly the ABL/land-surface scheme in the GCM.(iii) There is a need for intercomparisons of ABL and land-surface schemes used in GCMS, both for one- dimensional stand-alone models and for GCMs that incorporate the respective schemes.

Assessing urban vacant land ecosystem services: Urban vacant land as green infrastructure in the City of Roanoke, Virginia

Treesearch

Gunwoo Kim; Patrick A. Miller; David J. Nowak

2015-01-01

The research reported here quantifies the ecosystem services and values of vacant land using the City of Roanoke, Virginia as a study site. Aerial photo interpretation with ground-truthing was used to identify and catalog vacant parcels of land within the city limits and the results mapped using the i-Tree Canopy and i-Tree Eco models to define land cover classes and...

Impact of urban canopy models and external parameters on the modelled urban energy balance in a tropical city

NASA Astrophysics Data System (ADS)

Demuzere, Matthias; Harshan, Suraj; Järvi, Leena; Roth, Matthias; Betham Grimmond, Christine Susan; Masson, Valéry; Oleson, Keith; Velasco Saldana, Hector Erik; Wouters, Hendrik

2017-04-01

This paper provides the first comparative evaluation of four urban land surface models for a tropical residential neighbourhood in Singapore. The simulations are performed offline, for an 11-month period, using the bulk scheme TERRA_URB and three models of intermediate complexity (CLM, SURFEX and SUEWS). In addition, information from three different parameter lists are added to quantify the impact (interaction) of (between) external parameter settings and model formulations on the modelled urban energy balance components. Overall, the models' performance using the reference parameters aligns well with previous findings for mid- and high-latitude sites against (for) which the models are generally optimised (evaluated). The various combinations of models and different parameter values suggest that error statistics tend to be more dominated by the choice of the latter than the choice of model. Stratifying the observation period into dry / wet periods and hours since selected precipitation events reveals that the models' skill generally deteriorates during dry periods while e.g. CLM/SURFEX has a positive bias in the latent heat flux directly after a precipitation event. It is shown that the latter is due to simple representation of water intercepted on the impervious surfaces. In addition, the positive bias in modelled outgoing longwave radiation is attributed to neglecting the interactions between water vapor and radiation between the surface and the tower sensor. These findings suggest that future developments in urban climate research should continue the integration of more physically-based processes in urban canopy models, ensure the consistency between the observed and modelled atmospheric properties and focus on the correct representation of urban morphology and thermal and radiative characteristics.

Invasive Shrub Mapping in an Urban Environment from Hyperspectral and LiDAR-Derived Attributes

PubMed Central

Chance, Curtis M.; Coops, Nicholas C.; Plowright, Andrew A.; Tooke, Thoreau R.; Christen, Andreas; Aven, Neal

2016-01-01

Proactive management of invasive species in urban areas is critical to restricting their overall distribution. The objective of this work is to determine whether advanced remote sensing technologies can help to detect invasions effectively and efficiently in complex urban ecosystems such as parks. In Surrey, BC, Canada, Himalayan blackberry (Rubus armeniacus) and English ivy (Hedera helix) are two invasive shrub species that can negatively affect native ecosystems in cities and managed urban parks. Random forest (RF) models were created to detect these two species using a combination of hyperspectral imagery, and light detection and ranging (LiDAR) data. LiDAR-derived predictor variables included irradiance models, canopy structural characteristics, and orographic variables. RF detection accuracy ranged from 77.8 to 87.8% for Himalayan blackberry and 81.9 to 82.1% for English ivy, with open areas classified more accurately than areas under canopy cover. English ivy was predicted to occur across a greater area than Himalayan blackberry both within parks and across the entire city. Both Himalayan blackberry and English ivy were mostly located in clusters according to a Local Moran’s I analysis. The occurrence of both species decreased as the distance from roads increased. This study shows the feasibility of producing highly accurate detection maps of plant invasions in urban environments using a fusion of remotely sensed data, as well as the ability to use these products to guide management decisions. PMID:27818664

Assessment of Planetary-Boundary-Layer Schemes in the Weather Research and Forecasting Model Within and Above an Urban Canopy Layer

NASA Astrophysics Data System (ADS)

Ferrero, Enrico; Alessandrini, Stefano; Vandenberghe, Francois

2018-03-01

We tested several planetary-boundary-layer (PBL) schemes available in the Weather Research and Forecasting (WRF) model against measured wind speed and direction, temperature and turbulent kinetic energy (TKE) at three levels (5, 9, 25 m). The Urban Turbulence Project dataset, gathered from the outskirts of Turin, Italy and used for the comparison, provides measurements made by sonic anemometers for more than 1 year. In contrast to other similar studies, which have mainly focused on short-time periods, we considered 2 months of measurements (January and July) representing both the seasonal and the daily variabilities. To understand how the WRF-model PBL schemes perform in an urban environment, often characterized by low wind-speed conditions, we first compared six PBL schemes against observations taken by the highest anemometer located in the inertial sub-layer. The availability of the TKE measurements allows us to directly evaluate the performances of the model; results of the model evaluation are presented in terms of quantile versus quantile plots and statistical indices. Secondly, we considered WRF-model PBL schemes that can be coupled to the urban-surface exchange parametrizations and compared the simulation results with measurements from the two lower anemometers located inside the canopy layer. We find that the PBL schemes accounting for TKE are more accurate and the model representation of the roughness sub-layer improves when the urban model is coupled to each PBL scheme.

Environmental and biological controls of urban tree transpiration in the Upper Midwest

NASA Astrophysics Data System (ADS)

Peters, E. B.; McFadden, J.; Montgomery, R.

2009-12-01

Urban trees provide a variety of ecosystem services to urban and suburban areas, including carbon uptake, climate amelioration, energy reduction, and stormwater management. Tree transpiration, in particular, modifies urban water budgets by providing an alternative pathway for water after rain events. The relative importance of environmental and biological controls on transpiration are poorly understood in urban areas, yet these controls are important for quantifying and scaling up the ecosystem services that urban trees provide at landscape and regional scales and predicting how urban ecosystems will respond to climate changes. The objectives of our study were to quantify the annual cycle of tree transpiration in an urban ecosystem and to determine how different urban tree species and plant functional types respond to environmental drivers. We continuously measured whole-tree transpiration using thermal dissipation sap flow at four urban forest stands that were broadly representative of the species composition and tree sizes found in a suburban residential neighborhood of Minneapolis-Saint Paul, Minnesota. A total of 40 trees, representing different species, plant functional types, successional stages, and xylem anatomy, were sampled throughout the 2007 and 2008 growing seasons (April-November). At each site we monitored soil moisture, air temperature, and relative humidity continuously, and we measured leaf area index weekly. Urban tree transpiration was strongly correlated with diurnal changes in vapor pressure deficit and photosynthetically active radiation and with seasonal changes in leaf area index. We found that plant functional type better explained species differences in transpiration per canopy area than either successional stage or xylem anatomy, largely due to differences in canopy structure between conifer and broad-leaf deciduous trees. We also observed inter-annual differences in transpiration rates due to a mid-season drought and longer growing season in 2007, compared with the cooler, wetter conditions in 2008. These results were scaled to estimate the relative contribution of each tree type at the scale of a suburban landscape. The findings of this study have implications for understanding the role of trees in managing urban water budgets and predicting the impacts of climate change on urban ecosystem services.

Effects of sub-Arctic shrub canopies on snowmelt energetics

NASA Astrophysics Data System (ADS)

Bewley, D.; Essery, R.; Pomeroy, J.

2006-12-01

Much of the low Arctic is covered with shrub tundra, and there is increasing evidence that snowmelt rates are substantially different between shrub tundra and poorly vegetated sites. The cause of this remains uncertain, however, and extends beyond simple differences in albedo. Results are presented in this study from a detailed field investigation at Wolf Creek Research Basin in 2004 to determine the effect of two different shrub canopy structures on both melt rates and the partitioning of melt energy. The low shrub site (LSS) was essentially an unvegetated snowfield prior to melt (mean albedo ~0.85), and shrubs only became exposed during the last few days of melt reaching a mean height of 0.31 m and mean Plant Area Index (PAI) of 0.32. Shrubs at the tall shrub site (TSS) were partially buried initially (shrub fraction, mean height and PAI of 0.2, 0.9 m and 0.41) but dominated the landscape by the end of melt (corresponding values of 0.71, 1.6 m and 0.6). Melt rates were higher at TSS up until the exposure of shrubs and bare ground at LSS, after which the rates converged. A Shrub-Snow Canopy Model (SSCM) is developed to improve snowmelt simulations for shrub canopies by parameterizing the key shrub effects on surface fluxes, including the extinction of shortwave irradiance beneath shrubs and in canopy gaps, and the enhancement of snow surface fluxes of longwave radiation and sensible heat. SSCM was run for LSS assuming no shrubs were present above the variable snow and bare ground tiles, whereas for TSS an increasing shrub fraction above each tile was prescribed from observations. Results from both sites suggest that sensible heat fluxes contributed more melt energy than net radiation, and were greater during early melt at TSS due to the warming of exposed shrubs. SWE was accurately predicted against transect measurements at TSS (rms error 4 mm), but was overestimated at LSS (rms error 13 mm) since both air temperatures and turbulent transport were underestimated by not incorporating shrubs. This demonstrates the need to incorporate the rapid change in surface conditions associated with any shrub canopy (low or tall) within land surface and hydrological models. Most of the information required for running SSCM at other (tall) shrub canopies can be obtained remotely from photos or images of sufficiently high resolution to delineate individual shrub patches and canopy gaps.

Crop modeling: Studying the effect of water stress on the driving forces governing plant water potential

NASA Astrophysics Data System (ADS)

van Emmerik, T. H. M.; Mirfenderesgi, G.; Bohrer, G.; Steele-Dunne, S. C.; Van De Giesen, N.

2015-12-01

Water stress is one of the most important environmental factors that influence plant water dynamics. To prevent excessive water loss and physiological damage, plants can regulate transpiration by adjusting the stomatal aperture. This enhances survival, but also reduced photosynthesis and productivity. During periods of low water availability, stomatal regulation is a trade-off between optimization of either survival or production. Water stress defence mechanisms lead to significant changes in plant dynamics, e.g. leaf and stem water content. Recent research has shown that water content in a corn canopy can change up to 30% diurnally as a result of water stress, which has a considerable influence on radar backscatter from a corn canopy [1]. This highlighted the potential of water stress detection using radar. To fully explore the potential of water stress monitoring using radar, we need to understand the driving forces governing plant water potential. For this study, the recently developed the Finite-Element Tree-Crown Hydrodynamic model version 2 (FETCH2) model is applied to a corn canopy. FETCH2 is developed to resolve the hydrodynamic processes within a plant using the porous media analogy, allowing investigation of the influence of environmental stress factors on plant dynamics such as transpiration, photosynthesis, stomatal conductance, and leaf and stem water content. The model is parameterized and evaluated using a detailed dataset obtained during a three-month field experiment in Flevoland, the Netherlands, on a corn canopy. [1] van Emmerik, T., S. Steele-Dunne, J. Judge and N. van de Giesen: "Impact of Diurnal Variation in Vegetation Water Content on Radar Backscatter of Maize During Water Stress", Geosciences and Remote Sensing, IEEE Transactions on, vol. 52, issue 7, doi: 10.1109/TGRS.2014.2386142, 2015.

Reducing the uncertainty in the projection of the terrestrial carbon cycle by fusing models with remote sensing data

NASA Astrophysics Data System (ADS)

Serbin, S.; Shiklomanov, A. N.; Viskari, T.; Desai, A. R.; Townsend, P. A.; Dietze, M.

2015-12-01

Modeling global change requires accurate representation of terrestrial carbon (C), energy and water fluxes. In particular, capturing the properties of vegetation canopies that describe the radiation regime are a key focus for global change research because the properties related to radiation utilization and penetration within plant canopies provide an important constraint on terrestrial ecosystem productivity, as well as the fluxes of water and energy from vegetation to the atmosphere. As such, optical remote sensing observations present an important, and as yet relatively untapped, source of observations that can be used to inform modeling activities. In particular, high-spectral resolution optical data at the leaf and canopy scales offers the potential for an important and direct data constraint on the parameterization and structure of the radiative transfer model (RTM) scheme within ecosystem models across diverse vegetation types, disturbance and management histories. In this presentation we highlight ongoing work to integrate optical remote sensing observations, specifically leaf and imaging spectroscopy (IS) data across a range of forest ecosystems, into complex ecosystem process models within an efficient computational assimilation framework as a means to improve the description of canopy optical properties, vegetation composition, and modeled radiation balance. Our work leverages the Predictive Ecosystem Analyzer (PEcAn; http://www.pecanproject.org/) ecoinformatics toolbox together with a RTM module designed for efficient assimilation of leaf and IS observations to inform vegetation optical properties as well as associated plant traits. Ultimately, an improved understanding of the radiation balance of ecosystems will provide a better constraint on model projections of energy balance, vegetation composition, and carbon pools and fluxes thus allowing for a better diagnosis of the vulnerability of terrestrial ecosystems in response to global change.

Urban forest ecosystem analysis using fused airborne hyperspectral and lidar data

NASA Astrophysics Data System (ADS)

Alonzo, Mike Gerard

Urban trees are strategically important in a city's effort to mitigate their carbon footprint, heat island effects, air pollution, and stormwater runoff. Currently, the most common method for quantifying urban forest structure and ecosystem function is through field plot sampling. However, taking intensive structural measurements on private properties throughout a city is difficult, and the outputs from sample inventories are not spatially explicit. The overarching goal of this dissertation is to develop methods for mapping urban forest structure and function using fused hyperspectral imagery and waveform lidar data at the individual tree crown scale. Urban forest ecosystem services estimated using the USDA Forest Service's i-Tree Eco (formerly UFORE) model are based largely on tree species and leaf area index (LAI). Accordingly, tree species were mapped in my Santa Barbara, California study area for 29 species comprising >80% of canopy. Crown-scale discriminant analysis methods were introduced for fusing Airborne Visible Infrared Imaging Spectrometry (AVIRIS) data with a suite of lidar structural metrics (e.g., tree height, crown porosity) to maximize classification accuracy in a complex environment. AVIRIS imagery was critical to achieving an overall species-level accuracy of 83.4% while lidar data was most useful for improving the discrimination of small and morphologically unique species. LAI was estimated at both the field-plot scale using laser penetration metrics and at the crown scale using allometry. Agreement of the former with photographic estimates of gap fraction and the latter with allometric estimates based on field measurements was examined. Results indicate that lidar may be used reasonably to measure LAI in an urban environment lacking in continuous canopy and characterized by high species diversity. Finally, urban ecosystem services such as carbon storage and building energy-use modification were analyzed through combination of aforementioned methods and the i-Tree Eco modeling framework. The remote sensing methods developed in this dissertation will allow researchers to more precisely constrain urban ecosystem spatial analyses and equip cities to better manage their urban forest resource.

Streams in the urban heat island: spatial and temporal variability in temperature

USGS Publications Warehouse

Somers, Kayleigh A.; Bernhardt, Emily S.; Grace, James B.; Hassett, Brooke A.; Sudduth, Elizabeth B.; Wang, Siyi; Urban, Dean L.

2013-01-01

Streams draining urban heat islands tend to be hotter than rural and forested streams at baseflow because of warmer urban air and ground temperatures, paved surfaces, and decreased riparian canopy. Urban infrastructure efficiently routes runoff over hot impervious surfaces and through storm drains directly into streams and can lead to rapid, dramatic increases in temperature. Thermal regimes affect habitat quality and biogeochemical processes, and changes can be lethal if temperatures exceed upper tolerance limits of aquatic fauna. In summer 2009, we collected continuous (10-min interval) temperature data in 60 streams spanning a range of development intensity in the Piedmont of North Carolina, USA. The 5 most urbanized streams averaged 21.1°C at baseflow, compared to 19.5°C in the 5 most forested streams. Temperatures in urban streams rose as much as 4°C during a small regional storm, whereas the same storm led to extremely small to no changes in temperature in forested streams. Over a kilometer of stream length, baseflow temperature varied by as much as 10°C in an urban stream and as little as 2°C in a forested stream. We used structural equation modeling to explore how reach- and catchment-scale attributes interact to explain maximum temperatures and magnitudes of storm-flow temperature surges. The best predictive model of baseflow temperatures (R2  =  0.461) included moderately strong pathways directly (extent of development and road density) and indirectly, as mediated by reach-scale factors (canopy closure and stream width), from catchment-scale factors. The strongest influence on storm-flow temperature surges appeared to be % development in the catchment. Reach-scale factors, such as the extent of riparian forest and stream width, had little mitigating influence (R2  =  0.448). Stream temperature is an essential, but overlooked, aspect of the urban stream syndrome and is affected by reach-scale habitat variables, catchment-scale urbanization, and stream thermal regimes.

Flux measurements of energy and trace gases in urban Houston, Texas

NASA Astrophysics Data System (ADS)

Boedeker, I.; Schade, G. W.; Adams, S.; Park, C.

2008-12-01

We describe the setup and some first year results of a new flux measurements tower in an urban area. An existing radio communications tower 4 km north of downtown Houston was equipped with micrometeorological instrumentation and trace gas sampling lines in spring 2007. Wind speed, temperature and relative humidity are recorded at five levels between 12 and 60 m above ground; 3-D wind speed measurements, solar and net radiances, and trace gas sampling are established from the 60 m level. A closed path IRGA is used for CO2 and water vapor fluxes, and independent instrumentation for criteria pollutant and VOC fluxes. Two CSI data loggers and software control the measurements, and EdiRe software is used to analyze turbulence data and compute fluxes. A project description is provided at http://atmo.tamu.edu/yellowcabtower. Surface properties as calculated from the gradient measurements show the site to be surprisingly uniform, with displacement heights between 5 and 9 m and roughness lengths between 0.4 and 0.7 m, despite urban heterogeneity. The latter is investigated through visible/near IR orthoimagery and LIDAR data, which are incorporated into a local GIS. Net radiation was also only marginally affected by surface heterogeneity. At this urban location it is balanced by roughly equal amounts of sensible heat, latent heat, and storage fluxes. Latent heat flux, however, is smaller outside the growing season, with an equivalent increase in winter storage fluxes, as expected. Significant differences are also observed with direction during summer, showing decreased Bowen ratios and lower CO2 emissions from sectors with a larger urban tree canopy cover in the footprint. The largely mature, dominantly oak urban canopy cover alleviates approximately 100 W m- 2 during typical summer days. On the other hand, anthropogenic CO2 emissions dominate over photosynthetic uptake all year round. Measured carbon fluxes peak during morning rush-hour traffic, especially when increasing stretches of the main commuter road fall into the footprint. Outside the rush hour, daytime carbon fluxes typically ranged from 0.4 to 1.6 g C m-2 h-1. A seasonal comparison shows that up to 75% of midday anthropogenic carbon flux is removed via photosynthesis in the dominant wind sector, S, which bears typical tree canopy covers of 25-50% on pervious surfaces.

High-resolution visibility and air quality forecasting using multi-layer urban canopy model for highly urbanized Hong Kong and the Pearl River Delta

NASA Astrophysics Data System (ADS)

Piu NG, Chak; HAO, Song; Fat LAM, Yun

2015-04-01

Visibility is a universally critical element which affects the public in many aspects, including economic activities, health of local citizens and safety of marine transportation and aviation. The Interagency Monitoring of Protected Visual Environments (IMPROVE) visibility equation, an empirical equation developed by USEPA, has been modified by various studies to fit into the application upon the Asian continent including Hong Kong and China. Often these studies focused on the improvement of the existing IMPROVE equation by modifying its particulate speciation using local observation data. In this study, we developed an Integrated Forecast System (IFS) to predict the next-day air quality and visibility using Weather Research and Forecasting model with Building Energy Parameterization and Building Energy Model (WRF-BEP+BEM) and Community Multi-scale Air Quality Model (CMAQ). Unlike the other studies, the core of this study is to include detailed urbanization impacts with calibrated "IMPROVE equation for PRD" into the modeling system for Hong Kong's environs. The ultra-high resolution land cover information (~1km x 1km) from Google images, was digitized into the Geographic Information System (GIS) for preparing the model-ready input for IFS. The NCEP FNL (Final) Operation Global Analysis (FNL) and the Global Forecasting System (GFS) datasets were tested for both hind-cast and forecast cases, in order to calibrate the input of urban parameters in the WRF-BEP+BEM model. The evaluation of model performance with sensitivity cases was performed on sea surface temperature (SST), surface temperature (T), wind speed/direction with the major pollutants (i.e., PM10, PM2.5, NOx, SO2 and O3) using local observation and will be presented/discussed in this paper. References: 1. Y. L. Lee, R. Sequeira, Visibility degradation across Hong Kong its components and their relative contribution. Atmospheric Environment 2001, 35, 5861-5872. doi:10.1016/S1352-2310(01)00395-8 2. R. Zhang, Q. Bian, J. C. H. Fung, A. K. H. Lau, Mathematical modeling of seasonal variations in visibility in Hong Kong and the Pearl River Delta region. Atmospheric Environment 2013, 77, 803-816. http://dx.doi.org/10.1016/j.atmosenv.2013.05.048

EnviroAtlas - New York, NY - One Meter Resolution Urban Land Cover Data (2008) Web Service

EPA Pesticide Factsheets

This EnviroAtlas web service supports research and online mapping activities related to EnviroAtlas (https://www.epa.gov/enviroatlas ). The New York, NY EnviroAtlas Meter-scale Urban Land Cover (MULC) Data were generated by the University of Vermont Spatial Analysis Laboratory (SAL) under the direction of Jarlath O'Neil-Dunne as part of the United States Forest Service Urban Tree Canopy (UTC) assessment program. Seven classes were mapped using LiDAR and high resolution orthophotography: Tree Canopy, Grass/Shrub, Bare Soil, Water, Buildings, Roads/Railroads, and Other Paved Surfaces. These data were subsequently merged to fit with the EPA classification. The SAL project covered the five boroughs within the NYC city limits. However the EPA study area encompassed that area plus a 1 kilometer buffer. Additional land cover for the buffer area was generated from United States Department of Agriculture (USDA) National Agricultural Imagery Program (NAIP) four band (red, green, blue, and near infrared) aerial photography at 1 m spatial resolution from July, 2011 and LiDAR from 2010. Six land cover classes were mapped: water, impervious surfaces, soil and barren land, trees, grass-herbaceous non-woody vegetation, and agriculture. An accuracy assessment of 600 completely random and 55 stratified random photo interpreted reference points yielded an overall User's fuzzy accuracy of 87 percent. The area mapped is the US Census Bureau's 2010 Urban Statistical Area for New Yor

Urban Domestic Gardens (XIV): The Characteristics of Gardens in Five Cities

NASA Astrophysics Data System (ADS)

Loram, Alison; Warren, Philip H.; Gaston, Kevin J.

2008-09-01

Domestic gardens make substantial contributions to the provision of green space in urban areas. However, the ecological functions provided by such gardens depend critically on their configuration and composition. Here, we present the first detailed analysis of variation in the composition of urban gardens, in relation to housing characteristics and the nature of the surrounding landscape, across different cities in the United Kingdom. In all five cities studied (Belfast, Cardiff, Edinburgh, Leicester, and Oxford), garden size had an overwhelming influence on garden composition. Larger gardens supported more of the land-use types recorded, in greater extents, and were more likely to contain particular features, including tall trees and mature shrubs, areas of unmown grass and uncultivated land, vegetable patches, ponds, and composting sites. The proportional contribution of non-vegetated land-uses decreased as garden area increased. House age was less significant in determining the land-use within gardens, although older houses, which were more likely to be found further from the urban edge of the city, contained fewer hedges and greater areas of vegetation canopy >2 m in height. Current UK government planning recommendations will ultimately reduce the area of individual gardens and are thus predicted to result in fewer tall trees and, in particular, less vegetation canopy >2 m. This might be detrimental from ecological, aesthetic, social, and economic stand points.

Simulation of Surface Energy Fluxes and Snow Interception Using a Higher Order Closure Multi-Layer Soil-Vegetation-Atmospheric Model: The Effect of Canopy Shape and Structure

NASA Astrophysics Data System (ADS)

McGowan, L. E.; Dahlke, H. E.; Paw U, K. T.

2015-12-01

Snow cover is a critical driver of the Earth's surface energy budget, climate change, and water resources. Variations in snow cover not only affect the energy budget of the land surface but also represent a major water supply source. In California, US estimates of snow depth, extent, and melt in the Sierra Nevada are critical to estimating the amount of water available for both California agriculture and urban users. However, accurate estimates of snow cover and snow melt processes in forested area still remain a challenge. Canopy structure influences the vertical and spatiotemporal distribution of snow, and therefore ultimately determines the degree and extent by which snow alters both the surface energy balance and water availability in forested regions. In this study we use the Advanced Canopy-Atmosphere-Soil algorithm (ACASA), a multi-layer soil-vegetation-atmosphere numerical model, to simulate the effect of different snow-covered canopy structures on the energy budget, and temperature and other scalar profiles within different forest types in the Sierra Nevada, California. ACASA incorporates a higher order turbulence closure scheme which allows the detailed simulation of turbulent fluxes of heat and water vapor as well as the CO2 exchange of several layers within the canopy. As such ACASA can capture the counter gradient fluxes within canopies that may occur frequently, but are typically unaccounted for, in most snow hydrology models. Six different canopy types were modeled ranging from coniferous forests (e.g. most biomass near the ground) to top-heavy (e.g. most biomass near the top of the crown) deciduous forests to multi-layered forest canopies (e.g. mixture of young and mature trees). Preliminary results indicate that the canopy shape and structure associated with different canopy types fundamentally influence the vertical scalar profiles (including those of temperature, moisture, and wind speed) in the canopy and thus alter the interception and snow melt dynamics in forested land surfaces. The turbulent transport dynamics, including counter-gradient fluxes, and radiation features including land surface albedo, are discussed in the context of the snow energy balance.

Persistence of long-distance, insect-mediated pollen movement for a tropical canopy tree species in remnant forest patches in an urban landscape.

PubMed

Noreen, A M E; Niissalo, M A; Lum, S K Y; Webb, E L

2016-12-01

As deforestation and urbanization continue at rapid rates in tropical regions, urban forest patches are essential repositories of biodiversity. However, almost nothing is known about gene flow of forest-dependent tree species in urban landscapes. In this study, we investigated gene flow in the insect-pollinated, wind-dispersed tropical tree Koompassia malaccensis in and among three remnant forest patches in the urbanized landscape of Singapore. We genotyped the vast majority of adults (N=179) and a large number of recruits (N=2103) with 8 highly polymorphic microsatellite markers. Spatial genetic structure of the recruit and adult cohorts was significant, showing routine gene dispersal distances of ~100-400 m. Parentage analysis showed that 97% of recruits were within 100 m of their mother tree, and a high frequency of relatively short-distance pollen dispersal (median ~143-187 m). Despite routine seed and pollen dispersal distances of within a few hundred meters, interpatch gene flow occurred between all patches and was dominated by pollen movement: parentage analysis showed 76 pollen versus 2 seed interpatch dispersal events, and the seedling neighborhood model estimated ~1-6% seed immigration and ~21-46% pollen immigration rates, depending on patch. In addition, the smallest patch (containing five adult K. malaccensis trees) was entirely surrounded by >2.5 km of 'impervious' substrate, yet had the highest proportional pollen and seed immigration estimates of any patch. Hence, contrary to our hypothesis, insect-mediated gene flow persisted across an urban landscape, and several of our results also parallel key findings from insect-pollinated canopy trees sampled in mixed agricultural-forest landscapes.

Modelling Pollutant Dispersion in a Street Network

NASA Astrophysics Data System (ADS)

Salem, N. Ben; Garbero, V.; Salizzoni, P.; Lamaison, G.; Soulhac, L.

2015-04-01

This study constitutes a further step in the analysis of the performances of a street network model to simulate atmospheric pollutant dispersion in urban areas. The model, named SIRANE, is based on the decomposition of the urban atmosphere into two sub-domains: the urban boundary layer, whose dynamics is assumed to be well established, and the urban canopy, represented as a series of interconnected boxes. Parametric laws govern the mass exchanges between the boxes under the assumption that the pollutant dispersion within the canopy can be fully simulated by modelling three main bulk transfer phenomena: channelling along street axes, transfers at street intersections, and vertical exchange between street canyons and the overlying atmosphere. Here, we aim to evaluate the reliability of the parametrizations adopted to simulate these phenomena, by focusing on their possible dependence on the external wind direction. To this end, we test the model against concentration measurements within an idealized urban district whose geometrical layout closely matches the street network represented in SIRANE. The analysis is performed for an urban array with a fixed geometry and a varying wind incidence angle. The results show that the model provides generally good results with the reference parametrizations adopted in SIRANE and that its performances are quite robust for a wide range of the model parameters. This proves the reliability of the street network approach in simulating pollutant dispersion in densely built city districts. The results also show that the model performances may be improved by considering a dependence of the wind fluctuations at street intersections and of the vertical exchange velocity on the direction of the incident wind. This opens the way for further investigations to clarify the dependence of these parameters on wind direction and street aspect ratios.

Modeling Transport of Turbulent Fluxes in a Heterogeneous Urban Canopy Using a Spatially Explicit Energy Balance

NASA Astrophysics Data System (ADS)

Moody, M.; Bailey, B.; Stoll, R., II

2017-12-01

Understanding how changes in the microclimate near individual plants affects the surface energy budget is integral to modeling land-atmosphere interactions and a wide range of near surface atmospheric boundary layer phenomena. In urban areas, the complex geometry of the urban canopy layer results in large spatial deviations of turbulent fluxes further complicating the development of models. Accurately accounting for this heterogeneity in order to model urban energy and water use requires a sub-plant level understanding of microclimate variables. We present analysis of new experimental field data taken in and around two Blue Spruce (Picea pungens) trees at the University of Utah in 2015. The test sites were chosen in order study the effects of heterogeneity in an urban environment. An array of sensors were placed in and around the conifers to quantify transport in the soil-plant-atmosphere continuum: radiative fluxes, temperature, sap fluxes, etc. A spatial array of LEMS (Local Energy Measurement Systems) were deployed to obtain pressure, surrounding air temperature and relative humidity. These quantities are used to calculate the radiative and turbulent fluxes. Relying on measurements alone is insufficient to capture the complexity of microclimate distribution as one reaches sub-plant scales. A spatially-explicit radiation and energy balance model previously developed for deciduous trees was extended to include conifers. The model discretizes the tree into isothermal sub-volumes on which energy balances are performed and utilizes incoming radiation as the primary forcing input. The radiative transfer component of the model yields good agreement between measured and modeled upward longwave and shortwave radiative fluxes. Ultimately, the model was validated through an examination of the full energy budget including radiative and turbulent fluxes through isolated Picea pungens in an urban environment.

Structure of a forested urban park: implications for strategic management.

PubMed

Millward, Andrew A; Sabir, Senna

2010-11-01

Informed management of urban parks can provide optimal conditions for tree establishment and growth and thus maximize the ecological and aesthetic benefits that trees provide. This study assesses the structure, and its implications for function, of the urban forest in Allan Gardens, a 6.1 ha downtown park in the City of Toronto, Canada, using the Street Tree Resource Analysis Tool for Urban Forest Managers (STRATUM). Our goal is to present a framework for collection and analysis of baseline data that can inform a management strategy that would serve to protect and enhance this significant natural asset. We found that Allan Garden's tree population, while species rich (43), is dominated by maple (Acer spp.) (48% of all park trees), making it reliant on very few species for the majority of its ecological and aesthetic benefits and raising disease and pest-related concerns. Age profiles (using size as a proxy) showed a dominance of older trees with an inadequate number of individuals in the young to early middle age cohort necessary for short- to medium-term replacement. Because leaf area represents the single-most important contributor to urban tree benefits modelling, we calculated it separately for every park tree, using hemispheric photography, to document current canopy condition. These empirical measurements were lower than estimates produced by STRATUM, especially when trees were in decline and lacked full canopies, highlighting the importance of individual tree condition in determining leaf area and hence overall forest benefits. Stewardship of natural spaces within cities demands access to accurate and timely resource-specific data. Our work provides an uncomplicated approach to the acquisition and interpretation of these data in the context of a forested urban park. Copyright 2010 Elsevier Ltd. All rights reserved.

Urbanization Effects on the Vertical Distribution of Soil Microbial Communities and Soil C Storage across Edge-to-Interior Urban Forest Gradients

NASA Astrophysics Data System (ADS)

Rosier, C. L.; Van Stan, J. T., II; Trammell, T. L.

2017-12-01

Urbanization alters environmental conditions such as temperature, moisture, carbon (C) and nitrogen (N) deposition affecting critical soil processes (e.g., C storage). Urban soils experience elevated N deposition (e.g., transportation, industry) and decreased soil moisture via urban heat island that can subsequently alter soil microbial community structure and activity. However, there is a critical gap in understanding how increased temperatures and pollutant deposition influences soil microbial community structure and soil C/N cycling in urban forests. Furthermore, canopy structural differences between individual tree species is a potentially important mechanism facilitating the deposition of pollutants to the soil. The overarching goal of this study is to investigate the influence of urbanization and tree species structural differences on the bacterial and fungal community and C and N content of soils experiencing a gradient of urbanization pressures (i.e., forest edge to interior; 150-m). Soil cores (1-m depth) were collected near the stem (< 0.5 meter) of two tree species with contrasting canopy and bark structure (Fagus grandifolia, vs. Liriodendron tulipifera), and evaluated for soil microbial structure via metagenomic analysis and soil C/N content. We hypothesize that soil moisture constraints coupled with increases in recalcitrant C will decrease gram negative bacteria (i.e., dependent on labile C) while increasing saprophytic fungal community abundance (i.e., specialist consuming recalcitrant C) within both surface and subsurface soils experiencing the greatest urban pressure (i.e., forest edge). We further expect trees located on the edge of forest fragments will maintain greater surface soil (< 20 cm) C concentrations due to decreased soil moisture constraining microbial activity (e.g., slower decay), and increased capture of recalcitrant C stocks from industrial/vehicle emission sources (e.g., black C). Our initial results support our hypotheses that urbanization alters soil microbial community composition via reduced soil moisture and carbon storage potential via deposition gradients. Further analyses will answer important questions regarding how individual tree species alters urban soil C storage, N retention, and microbial dynamics.

Turbulent flow and scalar transport in a large wind farm

NASA Astrophysics Data System (ADS)

Porte-Agel, F.; Markfort, C. D.; Zhang, W.

2012-12-01

Wind energy is one of the fastest growing sources of renewable energy world-wide, and it is expected that many more large-scale wind farms will be built and cover a significant portion of land and ocean surfaces. By extracting kinetic energy from the atmospheric boundary layer and converting it to electricity, wind farms may affect the transport of momentum, heat, moisture and trace gases (e.g. CO_2) between the atmosphere and the land surface locally and globally. Understanding wind farm-atmosphere interaction is complicated by the effects of turbine array configuration, wind farm size, land-surface characteristics, and atmospheric thermal stability. A wind farm of finite length may be modeled as an added roughness or as a canopy in large-scale weather and climate models. However, it is not clear which analogy is physically more appropriate. Also, surface scalar flux is affected by wind farms and needs to be properly parameterized in meso-scale and/or high-resolution numerical models. Experiments involving model wind farms, with perfectly aligned and staggered configurations, having the same turbine distribution density, were conducted in a thermally-controlled boundary-layer wind tunnel. A neutrally stratified turbulent boundary layer was developed with a surface heat source. Measurements of the turbulent flow and fluxes over and through the wind farm were made using a custom x-wire/cold-wire anemometer; and surface scalar flux was measured with an array of surface-mounted heat flux sensors far within the quasi-developed region of the wind-farm. The turbulence statistics exhibit similar properties to those of canopy-type flows, but retain some characteristics of surface-layer flows in a limited region above the wind farms as well. The flow equilibrates faster and the overall momentum absorption is higher for the staggered compared to the aligned farm, which is consistent with canopy scaling and leads to a larger effective roughness. Although the overall surface heat flux change produced by the wind farms is found to be small, with a net reduction of 4% for the staggered wind farm and nearly zero change for the aligned wind farm, the highly heterogeneous spatial distribution of the surface heat flux, dependent on wind farm layout, is significant. This comprehensive first wind-tunnel dataset on turbulent flow and scalar transport in wind farms will be further used to develop and validate new parameterizations of surface fluxes in numerical models.

Utilising green and bluespace to mitigate urban heat island intensity.

PubMed

Gunawardena, K R; Wells, M J; Kershaw, T

2017-04-15

It has long been recognised that cities exhibit their own microclimate and are typically warmer than the surrounding rural areas. This 'mesoscale' influence is known as the urban heat island (UHI) effect and results largely from modification of surface properties leading to greater absorption of solar radiation, reduced convective cooling and lower water evaporation rates. Cities typically contain less vegetation and bodies of water than rural areas, and existing green and bluespace is often under threat from increasing population densities. This paper presents a meta-analysis of the key ways in which green and bluespace affect both urban canopy- and boundary-layer temperatures, examined from the perspectives of city-planning, urban climatology and climate science. The analysis suggests that the evapotranspiration-based cooling influence of both green and bluespace is primarily relevant for urban canopy-layer conditions, and that tree-dominated greenspace offers the greatest heat stress relief when it is most needed. However, the magnitude and transport of cooling experienced depends on size, spread, and geometry of greenspaces, with some solitary large parks found to offer minimal boundary-layer cooling. Contribution to cooling at the scale of the urban boundary-layer climate is attributed mainly to greenspace increasing surface roughness and thereby improving convection efficiency rather than evaporation. Although bluespace cooling and transport during the day can be substantial, nocturnal warming is highlighted as likely when conditions are most oppressive. However, when both features are employed together they can offer many synergistic ecosystem benefits including cooling. The ways in which green and bluespace infrastructure is applied in future urban growth strategies, particularly in countries expected to experience rapid urbanisation, warrants greater consideration in urban planning policy to mitigate the adverse effects of the UHI and enhance climate resilience. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

The Role of Vegetation and Mulch in Mitigating the Impact of Raindrops on Soils in Urban Vegetated Green Infrastructure Systems

NASA Astrophysics Data System (ADS)

Alizadehtazi, B.; Montalto, F. A.; Sjoblom, K.

2014-12-01

Raindrop impulses applied to soils can break up larger soil aggregates into smaller particles, dispersing them from their original position. The displaced particles can self-stratify, with finer particles at the top forming a crust. Occurrence of this phenomenon reduces the infiltration rate and increases runoff, contributing to downstream flooding, soil erosion, and non point source pollutant loads. Unprotected soil surfaces (e.g. without vegetation canopies, mulch, or other materials), are more susceptible to crust formation due to the higher kinetic energy associated with raindrop impact. By contrast, soil that is protected by vegetation canopies and mulch layers is less susceptible to crust formation, since these surfaces intercept raindrops, dissipating some of their kinetic energy prior to their impact with the soil. Within this context, this presentation presents preliminary laboratory work conducted using a rainfall simulator to determine the ability of new urban vegetation and mulch to minimize soil crust formation. Three different scenarios are compared: a) bare soil, b) soil with mulch cover, and c) soil protected by vegetation canopies. Soil moisture, surface penetration resistance, and physical measurements of the volume of infiltrate and runoff are made on all three surface treatments after simulated rainfall events. The results are used to develop recommendations regarding surface treatment in green infrastructure (GI) system designs, namely whether heavily vegetated GI facilities require mulching to maintain infiltration capacity.

Methods for Improving Fine-Scale Applications of the WRF-CMAQ Modeling System

EPA Science Inventory

Presentation on the work in AMAD to improve fine-scale (e.g. 4km and 1km) WRF-CMAQ simulations. Includes iterative analysis, updated sea surface temperature and snow cover fields, and inclusion of impervious surface information (urban parameterization).

Probabilistic modelling of overflow, surcharge and flooding in urban drainage using the first-order reliability method and parameterization of local rain series.

PubMed

Thorndahl, S; Willems, P

2008-01-01

Failure of urban drainage systems may occur due to surcharge or flooding at specific manholes in the system, or due to overflows from combined sewer systems to receiving waters. To quantify the probability or return period of failure, standard approaches make use of the simulation of design storms or long historical rainfall series in a hydrodynamic model of the urban drainage system. In this paper, an alternative probabilistic method is investigated: the first-order reliability method (FORM). To apply this method, a long rainfall time series was divided in rainstorms (rain events), and each rainstorm conceptualized to a synthetic rainfall hyetograph by a Gaussian shape with the parameters rainstorm depth, duration and peak intensity. Probability distributions were calibrated for these three parameters and used on the basis of the failure probability estimation, together with a hydrodynamic simulation model to determine the failure conditions for each set of parameters. The method takes into account the uncertainties involved in the rainstorm parameterization. Comparison is made between the failure probability results of the FORM method, the standard method using long-term simulations and alternative methods based on random sampling (Monte Carlo direct sampling and importance sampling). It is concluded that without crucial influence on the modelling accuracy, the FORM is very applicable as an alternative to traditional long-term simulations of urban drainage systems.

Implementation of rooftop reciculation parameterization into the QUIC fast response urban wind model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bagal, N.; Singh, B.; Pardyjak, E. R.

2004-01-01

The QUIC (Quick Urban & Industrial Complex) dispersion modeling system has been developed to provide high-resolution wind and concentration fields in cities. The fast response 3D urban wind model QUIC-URB explicitly solves for the flow field around buildings using a suite of empirical parameterizations and mass conservation. This procedure is based on the work of Rockle (1990). The current Rockle (1990) model does not capture the rooftop recirculation region associated with flow separation from the leading edge of an isolated building. According to Banks et al. (2001), there are two forms of separation depending on the incident wind angle. Formore » an incident wind angle within 20{sup o} of perpendicular to the front face of the building, 'bubble separation' occurs in which cylindrical vortices whose axis are orthogonal to the flow are generated along the rooftop surface (see Fig. 1). For a 'corner wind' flow or incident wind angle of 30{sup o} to 70{sup o} of perpendicular to the front face of the building, 'conical' or 'delta wing' vortices form along the roof surface (Fig. 3). In this work, a model for rooftop recirculation is implemented into the QUIC- URB model for the two incident wind angle regimes described above. The parameterizations for the length and height of the recirculation region are from Wilson (1979) for the case of flow perpendicular or near perpendicular to the building and from Banks et al. (2000) for the case of off-angle flow. In this paper, we describe the rooftop algorithms and show how the model results are improved through comparisons to experimental data (Snyder and Lawson 1994).« less

Excess Diffuse Light Absorption in Upper Mesophyll Limits CO2 Drawdown and Depresses Photosynthesis1[OPEN

PubMed Central

Gilbert, Matthew E.; McElrone, Andrew J.

2017-01-01

In agricultural and natural systems, diffuse light can enhance plant primary productivity due to deeper penetration into and greater irradiance of the entire canopy. However, for individual sun-grown leaves from three species, photosynthesis is actually less efficient under diffuse compared with direct light. Despite its potential impact on canopy-level productivity, the mechanism for this leaf-level diffuse light photosynthetic depression effect is unknown. Here, we investigate if the spatial distribution of light absorption relative to electron transport capacity in sun- and shade-grown sunflower (Helianthus annuus) leaves underlies its previously observed diffuse light photosynthetic depression. Using a new one-dimensional porous medium finite element gas-exchange model parameterized with light absorption profiles, we found that weaker penetration of diffuse versus direct light into the mesophyll of sun-grown sunflower leaves led to a more heterogenous saturation of electron transport capacity and lowered its CO2 concentration drawdown capacity in the intercellular airspace and chloroplast stroma. This decoupling of light availability from photosynthetic capacity under diffuse light is sufficient to generate an 11% decline in photosynthesis in sun-grown but not shade-grown leaves, primarily because thin shade-grown leaves similarly distribute diffuse and direct light throughout the mesophyll. Finally, we illustrate how diffuse light photosynthetic depression could overcome enhancement in canopies with low light extinction coefficients and/or leaf area, pointing toward a novel direction for future research. PMID:28432257

Excess Diffuse Light Absorption in Upper Mesophyll Limits CO2 Drawdown and Depresses Photosynthesis.

PubMed

Earles, J Mason; Théroux-Rancourt, Guillaume; Gilbert, Matthew E; McElrone, Andrew J; Brodersen, Craig R

2017-06-01

In agricultural and natural systems, diffuse light can enhance plant primary productivity due to deeper penetration into and greater irradiance of the entire canopy. However, for individual sun-grown leaves from three species, photosynthesis is actually less efficient under diffuse compared with direct light. Despite its potential impact on canopy-level productivity, the mechanism for this leaf-level diffuse light photosynthetic depression effect is unknown. Here, we investigate if the spatial distribution of light absorption relative to electron transport capacity in sun- and shade-grown sunflower ( Helianthus annuus ) leaves underlies its previously observed diffuse light photosynthetic depression. Using a new one-dimensional porous medium finite element gas-exchange model parameterized with light absorption profiles, we found that weaker penetration of diffuse versus direct light into the mesophyll of sun-grown sunflower leaves led to a more heterogenous saturation of electron transport capacity and lowered its CO 2 concentration drawdown capacity in the intercellular airspace and chloroplast stroma. This decoupling of light availability from photosynthetic capacity under diffuse light is sufficient to generate an 11% decline in photosynthesis in sun-grown but not shade-grown leaves, primarily because thin shade-grown leaves similarly distribute diffuse and direct light throughout the mesophyll. Finally, we illustrate how diffuse light photosynthetic depression could overcome enhancement in canopies with low light extinction coefficients and/or leaf area, pointing toward a novel direction for future research. © 2017 American Society of Plant Biologists. All Rights Reserved.

Statistical analysis and parameterization of the hygroscopic growth of the sub-micrometer urban background aerosol in Beijing

NASA Astrophysics Data System (ADS)

Wang, Yu; Wu, Zhijun; Ma, Nan; Wu, Yusheng; Zeng, Limin; Zhao, Chunsheng; Wiedensohler, Alfred

2018-02-01

The take-up of water of aerosol particles plays an important role in heavy haze formation over North China Plain, since it is related with particle mass concentration, visibility degradation, and particle chemistry. In the present study, we investigated the size-resolved hygroscopic growth factor (HGF) of sub-micrometer aerosol particles (smaller than 350 nm) on a basis of 9-month Hygroscopicity-Tandem Differential Mobility Analyzer measurement in the urban background atmosphere of Beijing. The mean hygroscopicity parameter (κ) values derived from averaging over the entire sampling period for particles of 50 nm, 75 nm, 100 nm, 150 nm, 250 nm, and 350 nm in diameters were 0.14 ± 0.07, 0.17 ± 0.05, 0.18 ± 0.06, 0.20 ± 0.07, 0.21 ± 0.09, and 0.23 ± 0.12, respectively, indicating the dominance of organics in the sub-micrometer urban aerosols. In the spring, summer, and autumn, the number fraction of hydrophilic particles increased with increasing particle size, resulting in an increasing trend of overall particle hygroscopicity with enhanced particle size. Differently, the overall mean κ values peaked in the range of 75-150 nm and decreased for particles larger than 150 nm in diameter during wintertime. Such size-dependency of κ in winter was related to the strong primary particle emissions from coal combustion during domestic heating period. The number fraction of hydrophobic particles such as freshly emitted soot decreased with increasing PM2.5 mass concentration, indicating aged and internal mixed particles were dominant in the severe particulate matter pollution. Parameterization schemes of the HGF as a function of relative humidity (RH) and particle size between 50 and 350 nm were determined for different seasons and pollution levels. The HGFs calculated from the parameterizations agree well with the measured HGFs at 20-90% RH. The parameterizations can be applied to determine the hygroscopic growth of aerosol particles at ambient conditions for the area of Beijing (ultrafine and fine particles) and the North China plain (fine particles).

Crowdsourcing urban air temperatures from smartphone battery temperatures

NASA Astrophysics Data System (ADS)

Overeem, A.; Robinson, J. C. R.; Leijnse, H.; Steeneveld, G. J.; Horn, B. K. P.; Uijlenhoet, R.

2013-08-01

Accurate air temperature observations in urban areas are important for meteorology and energy demand planning. They are indispensable to study the urban heat island effect and the adverse effects of high temperatures on human health. However, the availability of temperature observations in cities is often limited. Here we show that relatively accurate air temperature information for the urban canopy layer can be obtained from an alternative, nowadays omnipresent source: smartphones. In this study, battery temperatures were collected by an Android application for smartphones. A straightforward heat transfer model is employed to estimate daily mean air temperatures from smartphone battery temperatures for eight major cities around the world. The results demonstrate the enormous potential of this crowdsourcing application for real-time temperature monitoring in densely populated areas.

ON JOINT DETERMINISTIC GRID MODELING AND SUB-GRID VARIABILITY CONCEPTUAL FRAMEWORK FOR MODEL EVALUATION

EPA Science Inventory

The general situation, (but exemplified in urban areas), where a significant degree of sub-grid variability (SGV) exists in grid models poses problems when comparing gridbased air quality modeling results with observations. Typically, grid models ignore or parameterize processes ...

Modeling the resilience of urban water supply using the capital portfolio approach

NASA Astrophysics Data System (ADS)

Krueger, E. H.; Klammler, H.; Borchardt, D.; Frank, K.; Jawitz, J. W.; Rao, P. S.

2017-12-01

The dynamics of global change challenge the resilience of cities in a multitude of ways, including pressures resulting from population and consumption changes, production patterns, climate and landuse change, as well as environmental hazards. Responses to these challenges aim to improve urban resilience, but lack an adequate understanding of 1) the elements and processes that lead to the resilience of coupled natural-human-engineered systems, 2) the complex dynamics emerging from the interaction of these elements, including the availability of natural resources, infrastructure, and social capital, which may lead to 3) unintended consequences resulting from management responses. We propose a new model that simulates the coupled dynamics of five types of capitals (water resources, infrastructure, finances, political capital /management, and social adaptive capacity) that are necessary for the provision of water supply to urban residents. We parameterize the model based on data for a case study city, which is limited by constraints in water availability, financial resources, and faced with degrading infrastructure, as well as population increase, which challenge the urban management institutions. Our model analyzes the stability of the coupled system, and produces time series of the capital dynamics to quantify its resilience as a result of the portfolio of capitals available to usher adaptive capacity and to secure water supply subjected to multiple recurring shocks. We apply our model to one real urban water supply system located in an arid environment, as well as a wide range of hypothetical case studies, which demonstrates its applicability to various types of cities, and its ability to quantify and compare water supply resilience. The analysis of a range of urban water systems provides valuable insights into guiding more sustainable responses for maintaining the resilience of urban water supply around the globe, by showing how unsustainable responses risk the loss of resilience. We suggest that the same model can be generalized to represent other types of urban infrastructure service systems with different parameterizations.

Study of the effectiveness of several tree canopy types on roadside green belt in influencing the distribution of NO2 gas emitted from transportation

NASA Astrophysics Data System (ADS)

Desyana, R. D.; Sulistyantara, B.; Nasrullah, N.; Fatimah, I. S.

2017-03-01

Transportation is one significant factor which contributes to urban air pollution. One of the pollutants emitted from transportation which affect human’s health is NO2. Plants, especially trees, have high potential in reducing air pollutants from transportation through diffusion, absorbtion, adsorption and deposition. Purpose of this study was to analyze the effectiveness of several tree canopy types on roadside green belt in influencing distribution of NO2 gas emitted from transportation. The study conducted in three plots of tree canopy in Jagorawi Highway: Bungur (Lagerstroemia speciosa), Gmelina (Gmelina arborea) and Tanjung (Mimusops elengi). The tree canopy ability in absorbing pollutant is derived by comparing air quality on vegetated area with ambience air quality at control area (open field). Air sampling was conducted to measure NO2 concentration at elevation 1.5m, 5m and 10m at distance 0m, 10m and 30m, using Air Sampler Impinger. Concentration of NO2 was analyzed with Griess-Saltzman method. From this research, the result of ANOVA showed that tree plot (vegetated area) affected significantly to NO2 concentration. However the effect of distance from road and elevation was not significant. Among the plots, the highest NO2 concentration was found on Control plot (area without tree canopy), while the lowest NO2 concentration was found in Tanjung plot. Tanjung plot with round shape and high density canopy performed better in reducing NO2 than Bungur plot with round shape and medium density canopy, regardless the sampling elevation and distance. Gmelina plot performed the best in reducing horizontal distribution of NO2 concentration at elevation 1.5 and 5m, but the result at elevation 10m was not significant.

Reach-scale effects of riparian forest cover on urban stream ecosystems

USGS Publications Warehouse

Roy, A.H.; Faust, C.L.; Freeman, Mary C.; Meyer, J.L.

2005-01-01

We compared habitat and biota between paired open and forested reaches within five small streams (basin area 10?20 km2) in suburban catchments (9%?49% urban land cover) in the Piedmont of Georgia, USA. Stream reaches with open canopies were narrower than forested reaches (4.1 versus 5.0 m, respectively). There were no differences in habitat diversity (variation in velocity, depth, or bed particle size) between open and forested reaches. However, absence of local forest cover corresponded to decreased large wood and increased algal chlorophyll a standing crop biomass. These differences in basal food resources translated into higher densities of fishes in open (9.0 individuals?m?2) versus forested (4.9 individuals?m?2) reaches, primarily attributed to higher densities of the herbivore Campostoma oligolepis. Densities of terrestrial invertebrate inputs were higher in open reaches; however, trends suggested higher biomass of terrestrial inputs in forested reaches and a corresponding higher density of terrestrial prey consumed by water column feeding fishes. Reach-scale biotic integrity (macroinvertebrates, salamanders, and fishes) was largely unaffected by differences in canopy cover. In urbanizing areas where catchment land cover drives habitat and biotic quality, management practices that rely exclusively on forested riparian areas for stream protection are unlikely to be effective at maintaining ecosystem integrity.

Model developments in TERRA_URB, the upcoming standard urban parametrization of the atmospheric numerical model COSMO(-CLM)

NASA Astrophysics Data System (ADS)

Wouters, Hendrik; Blahak, Ulrich; Helmert, Jürgen; Raschendorfer, Matthias; Demuzere, Matthias; Fay, Barbara; Trusilova, Kristina; Mironov, Dmitrii; Reinert, Daniel; Lüthi, Daniel; Machulskaya, Ekaterina

2015-04-01

In order to address urban climate at the regional scales, a new efficient urban land-surface parametrization TERRA_URB has been developed and coupled to the atmospheric numerical model COSMO-CLM. Hereby, several new advancements for urban land-surface models are introduced which are crucial for capturing the urban surface-energy balance and its seasonal dependency in the mid-latitudes. This includes a new PDF-based water-storage parametrization for impervious land, the representation of radiative absorption and emission by greenhouse gases in the infra-red spectrum in the urban canopy layer, and the inclusion of heat emission from human activity. TERRA_URB has been applied in offline urban-climate studies during European observation campaigns at Basel (BUBBLE), Toulouse (CAPITOUL), and Singapore, and currently applied in online studies for urban areas in Belgium, Germany, Switzerland, Helsinki, Singapore, and Melbourne. Because of its computational efficiency, high accuracy and its to-the-point conceptual easiness, TERRA_URB has been selected to become the standard urban parametrization of the atmospheric numerical model COSMO(-CLM). This allows for better weather forecasts for temperature and precipitation in cities with COSMO, and an improved assessment of urban outdoor hazards in the context of global climate change and urban expansion with COSMO-CLM. We propose additional extensions to TERRA_URB towards a more robust representation of cities over the world including their structural design. In a first step, COSMO's standard EXTernal PARarameter (EXTPAR) tool is updated for representing the cities into the land cover over the entire globe. Hereby, global datasets in the standard EXTPAR tool are used to retrieve the 'Paved' or 'sealed' surface Fraction (PF) referring to the presence of buildings and streets. Furthermore, new global data sets are incorporated in EXTPAR for describing the Anthropogenic Heat Flux (AHF) due to human activity, and optionally the Surface Area Index (SAI) derived from the Floor Space Index (FSI). In a second step, it is focussed on the urban/rural contrast in terms of turbulent transport in the surface layer by means of model sensivity experiments: On the theoretical basis of the TKE-based surface-layer transfer scheme of COSMO, we investigate the consistency between empirical functions for thermal roughness lengths and the urban/rural canopy morphology.

A Grid of Fine Wire Thermocouples to Study the Spatial Coherence of Turbulence within Katabatic Flow through a Vineyard Canopy

NASA Astrophysics Data System (ADS)

Everard, K.; Christen, A.; Sturman, A.; Skaloud, P.

2016-12-01

Knowledge of the dynamics and thermodynamics of katabatic flow is relevant in vineyards, where grapevines are sensitive to temperature changes (frost protection and cooling). Basic understanding of the occurrence and evolution of, and turbulence within, katabatic flow is well known over bare slopes. However, little work has been completed to extend this understanding to mid-sized canopies and how the presence of a canopy affects the turbulent exchange of momentum and heat within the flow. Measurements were carried out over a 6° vineyard slope near Oliver, BC, Canada in the Okanagan Valley between July 5 and July 22, 2016. The set-up consisted of an array of five vertically arranged CSAT 3D (Campbell Scientific, Inc.) ultrasonic anemometers at z = 0.45 m, 0.90 m, 1.49 m, 2.34 m, and 4.73 m above ground level (AGL), and a 2-D grid of 40 Type-E (copper-constantan) fine-wire thermocouples (FWTC) arranged at the same heights as the CSAT 3D array on 8 masts extending in the upslope (flow) direction at locations x = 0.0 m (CSAT 3D tower), 0.5 m, 1.0 m, 2.0 m, 4.0 m, 8.0 m, 16.0 m, and 32.0 m. The FWTC array formed a sheet of 40 sampling points in the upslope-vertical plane. The height of the grapevine canopy (h) was approximately 2 m AGL, and rows were aligned along the local slope direction with a row spacing of 2.45 m. CSAT-3s were sampled at 60 Hz with 20 Hz data recording, the FWTCs were sampled at 2 Hz, all synchronized by a data logger. Katabatic flow was observed on several nights during the campaign, with a wind speed maximum located within the canopy. This contribution will focus on the measurement techniques, combining ultrasonic anemometer data with the spatially synchronized FWTC array using image process techniques. We identify the dynamics and structure of the katabatic flow, relevant for heat exchange, using the spatial coherence of the temperature field given by the FWTC array. Improved knowledge of the vertical structure and the dynamics of katabatic flow within canopies allows better understanding of how it influences mass transport and cold-air pooling within the immediate grapevine canopy. Such understanding allows for better vineyard planning and management, as well as parameterizing model approaches to assist in forecasting the effect of such events on the thermal environment.

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

EnviroAtlas - New York, NY - One Meter Resolution Urban Land Cover Data (2008)

EPA Pesticide Factsheets

The New York, NY EnviroAtlas Meter-scale Urban Land Cover (MULC) Data were generated by the University of Vermont Spatial Analysis Laboratory (SAL) under the direction of Jarlath O'Neil-Dunne as part of the United States Forest Service Urban Tree Canopy (UTC) assessment program. Seven classes were mapped using LiDAR and high resolution orthophotography: Tree Canopy, Grass/Shrub, Bare Soil, Water, Buildings, Roads/Railroads, and Other Paved Surfaces. These data were subsequently merged to fit with the EPA classification. The SAL project covered the five boroughs within the NYC city limits. However the EPA study area encompassed that area plus a 1 kilometer buffer. Additional land cover for the buffer area was generated from United States Department of Agriculture (USDA) National Agricultural Imagery Program (NAIP) four band (red, green, blue, and near infrared) aerial photography at 1 m spatial resolution from July, 2011 and LiDAR from 2010. Six land cover classes were mapped: water, impervious surfaces, soil and barren land, trees, grass-herbaceous non-woody vegetation, and agriculture. An accuracy assessment of 600 completely random and 55 stratified random photo interpreted reference points yielded an overall User's fuzzy accuracy of 87 percent. The area mapped is the US Census Bureau's 2010 Urban Statistical Area for New York City plus a 1 km buffer. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAt

Water in the Balance: A Parking Lot Story

NASA Astrophysics Data System (ADS)

Haas, N. A.; Vitousek, S.

2017-12-01

The greater Chicagoland region has seen a high degree of urbanization since 1970. For example, between 1970-1990 the region experienced 4% population growth, a 35% increase in urban land use, and approximately 454 square miles of agricultural land was mostly converted into urban uses. Transformation of land into urban uses in the Chicagoland region has altered the stream and catchment response to rainfall events, specifically an increase in stream flashiness and increase in urban flooding. Chicago has begun to address these changes through green infrastructure. To understand the impact of green infrastructure at local, city-wide, and watershed scales, individual projects need to be accurately and sufficiently modeled. A traditional parking lot conversion into a porous parking lot at the University of Illinois at Chicago was modeled using SWMM and scrutinized using field data to look at stormwater runoff and water balance prior and post reconstruction. SWMM modeling suggested an 87% reduction in peak flow as well as a 100% reduction in flooding for a 24 hour, 1.72-inch storm. For the same storm, field data suggest an 89% reduction in peak flow as well as a 100% reduction in flooding. Modeling suggested 100% reductions in flooding for longer duration storms (24 hour+) and a smaller reduction in peak flow ( 66%). The highly parameterized SWMM model agrees well with collected data and analysis. Further effort is being made to use data mining to create correlations within the collected datasets that can be integrated into a model that follows a standardized formation process and reduces parameterization.

An ecohydrologic model for a shallow groundwater urban environment.

PubMed

Arden, Sam; Ma, Xin Cissy; Brown, Mark

2014-01-01

The urban environment is a patchwork of natural and artificial surfaces that results in complex interactions with and impacts to natural hydrologic cycles. Evapotranspiration is a major hydrologic flow that is often altered through urbanization, although the mechanisms of change are sometimes difficult to tease out due to difficulty in effectively simulating soil-plant-atmosphere interactions. This paper introduces a simplified yet realistic model that is a combination of existing surface runoff and ecohydrology models designed to increase the quantitative understanding of complex urban hydrologic processes. Results demonstrate that the model is capable of simulating the long-term variability of major hydrologic fluxes as a function of impervious surface, temperature, water table elevation, canopy interception, soil characteristics, precipitation and complex mechanisms of plant water uptake. These understandings have potential implications for holistic urban water system management.

A Large Scale Biorational Approach Using Bacillus thuringiensis israeliensis (Strain AM65-52) for Managing Aedes aegypti Populations to Prevent Dengue, Chikungunya and Zika Transmission

PubMed Central

Pruszynski, Catherine A.; Hribar, Lawrence J.; Mickle, Robert; Leal, Andrea L.

2017-01-01

Background Aedes aegypti is a container-inhabiting mosquito and a vector of dengue, chikungunya, and Zika viruses. In 2009 several cases of autochthonous dengue transmission were reported in Key West, Florida, USA prompting a comprehensive response to control A. aegypti. In Key West, larvae of this mosquito develop in containers around human habitations which can be numerous and labor intensive to find and treat. Aerial applications of larvicide covering large areas in a short time can be an efficient and economical method to control A. aegypti. Bacillus thuringiensis israelensis (Bti) is a bacterial larvicide which is highly target specific and appropriate for wide area spraying over urban areas, but to date, there are no studies that evaluate aerial spraying of Bti to control container mosquitoes like A. aegypti. Methodology This paper examines the effectiveness of aerial larvicide applications using VectoBac® WG, a commercially available Bti formulation, for A. aegypti control in an urban setting in the USA. Droplet characteristics and spray drop deposition were evaluated in Key West, Florida, USA. The mortality of A. aegypti in containers placed under canopy in an urban environment was also evaluated. Efficacy of multiple larvicide applications on adult female A. aegypti population reduction was compared between an untreated control and treatment site. Conclusions Droplet characteristics showed that small droplets can penetrate through dense canopy to reach small containers. VectoBac WG droplets reached small containers under heavy canopy in sufficient amounts to cause > 55% mortality on all application days and >90% mortality on 3 of 5 application days while controls had <5% mortality. Aerial applications of VectoBac WG caused significant decrease in adult female populations throughout the summer and during the 38th week (last application) the difference in adult female numbers between untreated and treated sites was >50%. Aerial larvicide applications using VectoBac WG can cover wide areas in a short period of time and can be effective in controlling A. aegypti and reducing A. aegypti-borne transmission in urban areas similar to Key West, Florida, USA. PMID:28199323

Loss of urban forest canopy and the related effects on soundscape and human directed attention

NASA Astrophysics Data System (ADS)

Laverne, Robert James Paul

The specific questions addressed in this research are: Will the loss of trees in residential neighborhoods result in a change to the local soundscape? The investigation of this question leads to a related inquiry: Do the sounds of the environment in which a person is present affect their directed attention?. An invasive insect pest, the Emerald Ash Borer (Agrilus planipennis ), is killing millions of ash trees (genus Fraxinus) throughout North America. As the loss of tree canopy occurs, urban ecosystems change (including higher summer temperatures, more stormwater runoff, and poorer air quality) causing associated changes to human physical and mental health. Previous studies suggest that conditions in urban environments can result in chronic stress in humans and fatigue to directed attention, which is the ability to focus on tasks and to pay attention. Access to nature in cities can help refresh directed attention. The sights and sounds associated with parks, open spaces, and trees can serve as beneficial counterbalances to the irritating conditions associated with cities. This research examines changes to the quantity and quality of sounds in Arlington Heights, Illinois. A series of before-and-after sound recordings were gathered as trees died and were removed between 2013 and 2015. Comparison of recordings using the Raven sound analysis program revealed significant differences in some, but not all measures of sound attributes as tree canopy decreased. In general, more human-produced mechanical sounds (anthrophony) and fewer sounds associated with weather (geophony) were detected. Changes in sounds associated with animals (biophony) varied seasonally. Monitoring changes in the proportions of anthrophony, biophony and geophony can provide insight into changes in biodiversity, environmental health, and quality of life for humans. Before-tree-removal and after-tree-removal sound recordings served as the independent variable for randomly-assigned human volunteers as they performed the Stroop Test and the Necker Cube Pattern Control test to measure directed attention. The sound treatments were not found to have significant effects on the directed attention test scores. Future research is needed to investigate the characteristics of urban soundscapes that are detrimental or potentially conducive to human cognitive functioning.

Estimation of Anthropogenic Heat Emissions in Delhi, India and Their Role in Urban Heat Island Effect

NASA Astrophysics Data System (ADS)

Bhati, S.; Mohan, M.

2016-12-01

Energy consumption in the urban environment impacts the urban surface energy budget and leads to the emission of anthropogenic sensible heat into the atmosphere. Anthropogenic heat (AH) can vary both in time and space, and are not readily measured. In present study, anthropogenic heat emissions have been estimated using an inventory approach for Delhi. The main sources that have been considered are electricity consumption, vehicular emissions, fuel consumption in domestic sector and waste heat from power plants. Total estimated anthropogenic heat is apportioned gridwise (2 km2) and incorporated in the WRF (version 3.5) model coupled with single-layer Urban canopy model (UCM) to assess the impact of these emissions on urban heat island effect in Delhi. Vehicular emissions have been found to be highest contributor to anthropogenic heat emissions (47%) followed by electricity consumption (28%), domestic fuel consumption (16%) and waste heat from power plants (9%). Highest annual average anthropogenic heat flux was estimated to be 25.2 Wm-2. High flux zones are observed in east Delhi and densely occupied and commercial zones of Sitaram Bazar and Connaught Place. Inclusion of anthropogenic heat emissions in the model improves model performance for near surface temperature as well as urban heat island intensities. Maximum simulated night-time UHI improves from 5.95°C (without AH) to 6.24°C (with AH) against observed value of 6.68°C, thereby indicating positive contribution of anthropogenic heat emissions along with urban canopy towards UHI effect in Delhi. Similarly, spatial distribution and UHI hotspots are found to be comparatively closer to corresponding observed distribution and hotspots with anthropogenic heat emissions being added to the WRF model. Overall, relatively improved model performance is indicative of the impact of anthropogenic heat emissions in local urban meteorology and urban heat island effect in Delhi. Hence, rising population and change in land use-cover and associated anthropogenic activities call for strategic mitigation measures in the city to prevent further strengthening of heat island effect.

Combining surface reanalysis and remote sensing data for monitoring evapotranspiration

USGS Publications Warehouse

Marshall, M.; Tu, K.; Funk, C.; Michaelsen, J.; Williams, Pat; Williams, C.; Ardö, J.; Marie, B.; Cappelaere, B.; Grandcourt, A.; Nickless, A.; Noubellon, Y.; Scholes, R.; Kutsch, W.

2012-01-01

Climate change is expected to have the greatest impact on the world's poor. In the Sahel, a climatically sensitive region where rain-fed agriculture is the primary livelihood, expected decreases in water supply will increase food insecurity. Studies on climate change and the intensification of the water cycle in sub-Saharan Africa are few. This is due in part to poor calibration of modeled actual evapotranspiration (AET), a key input in continental-scale hydrologic models. In this study, a model driven by dynamic canopy AET was combined with the Global Land Data Assimilation System realization of the NOAH Land Surface Model (GNOAH) wet canopy and soil AET for monitoring purposes in sub-Saharan Africa. The performance of the hybrid model was compared against AET from the GNOAH model and dynamic model using eight eddy flux towers representing major biomes of sub-Saharan Africa. The greatest improvements in model performance are at humid sites with dense vegetation, while performance at semi-arid sites is poor, but better than individual models. The reduction in errors using the hybrid model can be attributed to the integration of a dynamic vegetation component with land surface model estimates, improved model parameterization, and reduction of multiplicative effects of uncertain data.

Insectivorous bats respond to vegetation complexity in urban green spaces.

PubMed

Suarez-Rubio, Marcela; Ille, Christina; Bruckner, Alexander

2018-03-01

Structural complexity is known to determine habitat quality for insectivorous bats, but how bats respond to habitat complexity in highly modified areas such as urban green spaces has been little explored. Furthermore, it is uncertain whether a recently developed measure of structural complexity is as effective as field-based surveys when applied to urban environments. We assessed whether image-derived structural complexity (MIG) was as/more effective than field-based descriptors in this environment and evaluated the response of insectivorous bats to structural complexity in urban green spaces. Bat activity and species richness were assessed with ultrasonic devices at 180 locations within green spaces in Vienna, Austria. Vegetation complexity was assessed using 17 field-based descriptors and by calculating the mean information gain (MIG) using digital images. Total bat activity and species richness decreased with increasing structural complexity of canopy cover, suggesting maneuverability and echolocation (sensorial) challenges for bat species using the canopy for flight and foraging. The negative response of functional groups to increased complexity was stronger for open-space foragers than for edge-space foragers. Nyctalus noctula , a species foraging in open space, showed a negative response to structural complexity, whereas Pipistrellus pygmaeus , an edge-space forager, was positively influenced by the number of trees. Our results show that MIG is a useful, time- and cost-effective tool to measure habitat complexity that complemented field-based descriptors. Response of insectivorous bats to structural complexity was group- and species-specific, which highlights the need for manifold management strategies (e.g., increasing or reinstating the extent of ground vegetation cover) to fulfill different species' requirements and to conserve insectivorous bats in urban green spaces.

Integrating a street-canyon model with a regional Gaussian dispersion model for improved characterisation of near-road air pollution

NASA Astrophysics Data System (ADS)

Fallah-Shorshani, Masoud; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2017-03-01

The development and use of dispersion models that simulate traffic-related air pollution in urban areas has risen significantly in support of air pollution exposure research. In order to accurately estimate population exposure, it is important to generate concentration surfaces that take into account near-road concentrations as well as the transport of pollutants throughout an urban region. In this paper, an integrated modelling chain was developed to simulate ambient Nitrogen Dioxide (NO2) in a dense urban neighbourhood while taking into account traffic emissions, the regional background, and the transport of pollutants within the urban canopy. For this purpose, we developed a hybrid configuration including 1) a street canyon model, which simulates pollutant transfer along streets and intersections, taking into account the geometry of buildings and other obstacles, and 2) a Gaussian puff model, which resolves the transport of contaminants at the top of the urban canopy and accounts for regional meteorology. Each dispersion model was validated against measured concentrations and compared against the hybrid configuration. Our results demonstrate that the hybrid approach significantly improves the output of each model on its own. An underestimation appears clearly for the Gaussian model and street-canyon model compared to observed data. This is due to ignoring the building effect by the Gaussian model and undermining the contribution of other roads by the canyon model. The hybrid approach reduced the RMSE (of observed vs. predicted concentrations) by 16%-25% compared to each model on its own, and increased FAC2 (fraction of predictions within a factor of two of the observations) by 10%-34%.

Leaf reflectance variation along a vertical crown gradient of two deciduous tree species in a Belgian industrial habitat.

PubMed

Khavaninzadeh, Ali Reza; Veroustraete, Frank; Van Wittenberghe, Shari; Verrelst, Jochem; Samson, Roeland

2015-09-01

The reflectometry of leaf asymmetry is a novel approach in the bio-monitoring of tree health in urban or industrial habitats. Leaf asymmetry responds to the degree of environmental pollution and reflects structural changes in a leaf due to environmental pollution. This paper describes the boundary conditions to scale up from leaf to canopy level reflectance, by describing the variability of adaxial and abaxial leaf reflectance, hence leaf asymmetry, along the crown height gradients of two tree species. Our findings open a research pathway towards bio-monitoring based on the airborne remote sensing of tree canopies and their leaf asymmetric properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

Supplementary data of “Impacts of mesic and xeric urban vegetation on outdoor thermal comfort and microclimate in Phoenix, AZ”

PubMed Central

Song, Jiyun; Wang, Zhi-Hua

2015-01-01

An advanced Markov-Chain Monte Carlo approach called Subset Simulation is described in Au and Beck (2001) [1] was used to quantify parameter uncertainty and model sensitivity of the urban land-atmospheric framework, viz. the coupled urban canopy model-single column model (UCM-SCM). The results show that the atmospheric dynamics are sensitive to land surface conditions. The most sensitive parameters are dimensional parameters, i.e. roof width, aspect ratio, roughness length of heat and momentum, since these parameters control the magnitude of sensible heat flux. The relative insensitive parameters are hydrological parameters since the lawns or green roofs in urban areas are regularly irrigated so that the water availability for evaporation is never constrained. PMID:26702421

Evaluation of Multiple Mechanistic Hypotheses of Leaf Photosynthesis and Stomatal Conductance against Diurnal and Seasonal Data from Two Contrasting Panamanian Tropical Forests

NASA Astrophysics Data System (ADS)

Serbin, S.; Walker, A. P.; Wu, J.; Ely, K.; Rogers, A.; Wolfe, B.

2017-12-01

Tropical forests play a key role in regulating the global carbon (C), water, and energy cycles and stores, as well as influence climate through the exchanges of mass and energy with the atmosphere. However, projected changes in temperature and precipitation patterns are expected to impact the tropics and the strength of the tropical C sink, likely resulting in significant climate feedbacks. Moreover, the impact of stronger, longer, and more extensive droughts not well understood. Critical for the accurate modeling of the tropical C and water cycle in Earth System Models (ESMs) is the representation of the coupled photosynthetic and stomatal conductance processes and how these processes are impacted by environmental and other drivers. Moreover, the parameterization and representation of these processes is an important consideration for ESM projections. We use a novel model framework, the Multi-Assumption Architecture and Testbed (MAAT), together with the open-source bioinformatics toolbox, the Predictive Ecosystem Analyzer (PEcAn), to explore the impact of the multiple mechanistic hypotheses of coupled photosynthesis and stomatal conductance as well as the additional uncertainty related to model parameterization. Our goal was to better understand how model choice and parameterization influences diurnal and seasonal modeling of leaf-level photosynthesis and stomatal conductance. We focused on the 2016 ENSO period and starting in February, monthly measurements of diurnal photosynthesis and conductance were made on 7-9 dominant species at the two Smithsonian canopy crane sites. This benchmark dataset was used to test different representations of stomatal conductance and photosynthetic parameterizations with the MAAT model, running within PEcAn. The MAAT model allows for the easy selection of competing hypotheses to test different photosynthetic modeling approaches while PEcAn provides the ability to explore the uncertainties introduced through parameterization. We found that stomatal choice can play a large role in model-data mismatch and observational constraints can be used to reduce simulated model spread, but can also result in large model disagreements with measurements. These results will be used to help inform the modeling of photosynthesis in tropical systems for the larger ESM community.

An analysis of urban thermal characteristics and associated land cover in Tampa Bay and Las Vegas using Landsat satellite data

USGS Publications Warehouse

Xian, George; Crane, Mike

2006-01-01

Remote sensing data from both Landsat 5 and Landsat 7 systems were utilized to assess urban area thermal characteristics in Tampa Bay watershed of west-central Florida, and the Las Vegas valley of southern Nevada. To quantitatively determine urban land use extents and development densities, sub-pixel impervious surface areas were mapped for both areas. The urban–rural boundaries and urban development densities were defined by selecting certain imperviousness threshold values and Landsat thermal bands were used to investigate urban surface thermal patterns. Analysis results suggest that urban surface thermal characteristics and patterns can be identified through qualitatively based urban land use and development density data. Results show the urban area of the Tampa Bay watershed has a daytime heating effect (heat-source), whereas the urban surface in Las Vegas has a daytime cooling effect (heat-sink). These thermal effects strongly correlated with urban development densities where higher percent imperviousness is usually associated with higher surface temperature. Using vegetation canopy coverage information, the spatial and temporal distributions of urban impervious surface and associated thermal characteristics are demonstrated to be very useful sources in quantifying urban land use, development intensity, and urban thermal patterns.

Evaluate dry deposition velocity of the nitrogen oxides using Noah-MP physics ensemble simulations for the Dinghushan Forest, Southern China

NASA Astrophysics Data System (ADS)

Zhang, Qi; Chang, Ming; Zhou, Shengzhen; Chen, Weihua; Wang, Xuemei; Liao, Wenhui; Dai, Jianing; Wu, ZhiYong

2017-11-01

There has been a rapid growth of reactive nitrogen (Nr) deposition over the world in the past decades. The Pearl River Delta region is one of the areas with high loading of nitrogen deposition. But there are still large uncertainties in the study of dry deposition because of its complex processes of physical chemistry and vegetation physiology. At present, the forest canopy parameterization scheme used in WRF-Chem model is a single-layer "big leaf" model, and the simulation of radiation transmission and energy balance in forest canopy is not detailed and accurate. Noah-MP land surface model (Noah-MP) is based on the Noah land surface model (Noah LSM) and has multiple parametric options to simulate the energy, momentum, and material interactions of the vegetation-soil-atmosphere system. Therefore, to investigate the improvement of the simulation results of WRF-Chem on the nitrogen deposition in forest area after coupled with Noah-MP model and to reduce the influence of meteorological simulation biases on the dry deposition velocity simulation, a dry deposition single-point model coupled by Noah- MP and the WRF-Chem dry deposition module (WDDM) was used to simulate the deposition velocity (Vd). The model was driven by the micro-meteorological observation of the Dinghushan Forest Ecosystem Location Station. And a series of numerical experiments were carried out to identify the key processes influencing the calculation of dry deposition velocity, and the effects of various surface physical and plant physiological processes on dry deposition were discussed. The model captured the observed Vd well, but still underestimated the Vd. The self-defect of Wesely scheme applied by WDDM, and the inaccuracy of built-in parameters in WDDM and input data for Noah-MP (e.g. LAI) were the key factors that cause the underestimation of Vd. Therefore, future work is needed to improve model mechanisms and parameterization.

Quantifying dominance of intra-storm phase of interception process by small isolated canopies

NASA Astrophysics Data System (ADS)

Yerk, Walter; Montalto, Franco

2014-05-01

Precipitation interception by vegetation canopies has long been recognized as a major component of the hydrologic cycle; however, historically most research has been dedicated to closed or sparse canopy forests. The goal of our research was to quantify rainfall partitioning by small isolated canopies in an urban setting. The field experiment involved small forms of four shrub species (Prunus laurocerasus, Cornus sericea, Itea virginica and Hydrangea quercifolia) with crown heights 40 - 80 cm and diameters 35 - 60 cm. Each plant had ten rain gauges to measure throughfall with a sampling frequency of 5 seconds. An on-site automated weather station provided meteorological data. Leaf area index (LAI) was measured by manual counting. We estimated the canopy storage capacities of all four species to be less than 0.5 mm. The obtained data showed statistically significant differences in interception properties among all four species, except between Cornus and Itea. Cumulative interception loss for the period of August-December 2013 was 10% for Cornus, 16% for Itea, 29% for Hydrangea, and 49% for Prunus. The observations revealed a weak relationship between interception abilities and LAI for all four species. Throughfall and precipitation intensities (mm/hr) expressed very strong linear relationship (adjusted coefficients of determination were from 0.80 to 0.95) for the entire range of observed rainfall intensities. For Cornus the ratio of throughfall to precipitation intensity was close to 0.93:1, for Itea it was 0.82:1. The ratios were lesser for Hydrangea (0.65:1), and especially for Prunus (0.48:1). Therefore we show that reduced by the canopy, throughfall intensity results in the bulk of precipitation depth intercepted during the rain events. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception. Simulations of potential evaporation based on the Penman-Monteith method showed a large underestimation of evaporation from the wet canopies during the rain events. Approaches other than energy balance models of potential evaporation from a still water surface are being discussed in order to explain large evaporation from within a wet isolated canopy.

Mapping forest canopy fuels in Yellowstone National Park using lidar and hyperspectral data

NASA Astrophysics Data System (ADS)

Halligan, Kerry Quinn

The severity and size of wildland fires in the forested western U.S have increased in recent years despite improvements in fire suppression efficiency. This, along with increased density of homes in the wildland-urban interface, has resulted in high costs for fire management and increased risks to human health, safety and property. Crown fires, in comparison to surface fires, pose an especially high risk due to their intensity and high rate of spread. Crown fire models require a range of quantitative fuel parameters which can be difficult and costly to obtain, but advances in lidar and hyperspectral sensor technologies hold promise for delivering these inputs. Further research is needed, however, to assess the strengths and limitations of these technologies and the most appropriate analysis methodologies for estimating crown fuel parameters from these data. This dissertation focuses on retrieving critical crown fuel parameters, including canopy height, canopy bulk density and proportion of dead canopy fuel, from airborne lidar and hyperspectral data. Remote sensing data were used in conjunction with detailed field data on forest parameters and surface reflectance measurements. A new method was developed for retrieving Digital Surface Model (DSM) and Digital Canopy Models (DCM) from first return lidar data. Validation data on individual tree heights demonstrated the high accuracy (r2 0.95) of the DCMs developed via this new algorithm. Lidar-derived DCMs were used to estimate critical crown fire parameters including available canopy fuel, canopy height and canopy bulk density with linear regression model r2 values ranging from 0.75 to 0.85. Hyperspectral data were used in conjunction with Spectral Mixture Analysis (SMA) to assess fuel quality in the form of live versus dead canopy proportions. Severity and stage of insect-caused forest mortality were estimated using the fractional abundance of green vegetation, non-photosynthetic vegetation and shade obtained from SMA. Proportion of insect attack was estimated with a linear model producing an r2 of 0.6 using SMA and bark endmembers from image and reference libraries. Fraction of red attack, with a possible link to increased crown fire risk, was estimated with an r2 of 0.45.

Designing a Multi-Objective Multi-Support Accuracy Assessment of the 2001 National Land Cover Data (NLCD 2001) of the Conterminous United States

EPA Science Inventory

The database design and diverse application of NLCD 2001 pose significant challenges for accuracy assessment because numerous objectives are of interest, including accuracy of land cover, percent urban imperviousness, percent tree canopy, land-cover composition, and net change. ...

Potential canopy interception of nitrogen in the Pacific Northwest, USA

Treesearch

Jeffrey M. Klopatek; Matthew J. Barry; Dale W. Johnson

2006-01-01

Nitrogen deposition is increasing worldwide from anthropogenic sources and encroactring upon previously N limited ecosystems. Recent literature reports increases in inorganic N deposition in Pacific Northwest forests of the United States due to expanding urbanization. We examined the contributions of atmospheric deposition of inorganic N to old-growth and second-growth...

Brooklyn's urban forest

Treesearch

David J. Nowak; Daniel E. Crane; Jack C. Stevens; Myriam Ibarra

2002-01-01

An assessment of trees in Brooklyn, New York, reveal that this borough has approximately 610,000 trees with canopies that cover 11.4 percent of the area. The most common trees are estimated to be tree of heaven, white mulberry, black locust, Norway maple and black cherry. Brooklyn's trees currently store approximately 172,000 metric tons of carbon with an...

Trees grow on money: urban tree canopy cover and environmental justice.

PubMed

Schwarz, Kirsten; Fragkias, Michail; Boone, Christopher G; Zhou, Weiqi; McHale, Melissa; Grove, J Morgan; O'Neil-Dunne, Jarlath; McFadden, Joseph P; Buckley, Geoffrey L; Childers, Dan; Ogden, Laura; Pincetl, Stephanie; Pataki, Diane; Whitmer, Ali; Cadenasso, Mary L

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman's correlation, ordinary least squares regression (OLS), and a spatial autoregressive model (SAR). Across all cities there is a strong positive correlation between UTC cover and median household income. Negative correlations between race and UTC cover exist in bivariate models for some cities, but they are generally not observed using multivariate regressions that include additional variables on income, education, and housing age. SAR models result in higher r-square values compared to the OLS models across all cities, suggesting that spatial autocorrelation is an important feature of our data. Similarities among cities can be found based on shared characteristics of climate, race/ethnicity, and size. Our findings suggest that a suite of variables, including income, contribute to the distribution of UTC cover. These findings can help target simultaneous strategies for UTC goals and environmental justice concerns.

Water-Channel Estimation of Eulerian and Lagrangian Time Scales of the Turbulence in Idealized Two-Dimensional Urban Canopies

NASA Astrophysics Data System (ADS)

Di Bernardino, Annalisa; Monti, Paolo; Leuzzi, Giovanni; Querzoli, Giorgio

2017-11-01

Lagrangian and Eulerian statistics are obtained from a water-channel experiment of an idealized two-dimensional urban canopy flow in neutral conditions. The objective is to quantify the Eulerian (TE) and Lagrangian (TL) time scales of the turbulence above the canopy layer as well as to investigate their dependence on the aspect ratio of the canopy, AR, as the latter is the ratio of the width ( W) to the height ( H) of the canyon. Experiments are also conducted for the case of flat terrain, which can be thought of as equivalent to a classical one-directional shear flow. The values found for the Eulerian time scales on flat terrain are in agreement with previous numerical results found in the literature. It is found that both the streamwise and vertical components of the Lagrangian time scale, T_u^L and T_w^L , follow Raupach's linear law within the constant-flux layer. The same holds true for T_w^L in both the canopies analyzed (AR= 1 and AR= 2) and also for T_u^L when AR = 1. In contrast, for AR = 2, T_u^L follows Raupach's law only above z=2H. Below that level, T_u^L is nearly constant with height, showing at z=H a value approximately one order of magnitude greater than that found for AR = 1. It is shown that the assumption usually adopted for flat terrain, that β =TL/TE is proportional to the inverse of the turbulence intensity, also holds true even for the canopy flow in the constant-flux layer. In particular, γ /i_u fits well β _u =T_u^L /T_u^E in both the configurations by choosing γ to be 0.35 (here, i_u =σ _u / \\bar{u} , where \\bar{u} and σ _u are the mean and the root-mean-square of the streamwise velocity component, respectively). On the other hand, β _w =T_w^L /T_w^E follows approximately γ /i_w =0.65/( {σ _w /\\bar{u} } ) for z > 2H, irrespective of the AR value. The second main objective is to estimate other parameters of interest in dispersion studies, such as the eddy diffusivity of momentum (KT) and the Kolmogorov constant (C_0). It is found that C_0 depends appreciably on the velocity component both for the flat terrain and canopy flow, even though for the latter case it is insensitive to AR values. In all the three experimental configurations analyzed here, KT shows an overall linear growth with height in agreement with the linear trend predicted by Prandtl's theory.

PALM-USM v1.0: A new urban surface model integrated into the PALM large-eddy simulation model

NASA Astrophysics Data System (ADS)

Resler, Jaroslav; Krč, Pavel; Belda, Michal; Juruš, Pavel; Benešová, Nina; Lopata, Jan; Vlček, Ondřej; Damašková, Daša; Eben, Kryštof; Derbek, Přemysl; Maronga, Björn; Kanani-Sühring, Farah

2017-10-01

Urban areas are an important part of the climate system and many aspects of urban climate have direct effects on human health and living conditions. This implies that reliable tools for local urban climate studies supporting sustainable urban planning are needed. However, a realistic implementation of urban canopy processes still poses a serious challenge for weather and climate modelling for the current generation of numerical models. To address this demand, a new urban surface model (USM), describing the surface energy processes for urban environments, was developed and integrated as a module into the PALM large-eddy simulation model. The development of the presented first version of the USM originated from modelling the urban heat island during summer heat wave episodes and thus implements primarily processes important in such conditions. The USM contains a multi-reflection radiation model for shortwave and longwave radiation with an integrated model of absorption of radiation by resolved plant canopy (i.e. trees, shrubs). Furthermore, it consists of an energy balance solver for horizontal and vertical impervious surfaces, and thermal diffusion in ground, wall, and roof materials, and it includes a simple model for the consideration of anthropogenic heat sources. The USM was parallelized using the standard Message Passing Interface and performance testing demonstrates that the computational costs of the USM are reasonable on typical clusters for the tested configurations. The module was fully integrated into PALM and is available via its online repository under the GNU General Public License (GPL). The USM was tested on a summer heat-wave episode for a selected Prague crossroads. The general representation of the urban boundary layer and patterns of surface temperatures of various surface types (walls, pavement) are in good agreement with in situ observations made in Prague. Additional simulations were performed in order to assess the sensitivity of the results to uncertainties in the material parameters, the domain size, and the general effect of the USM itself. The first version of the USM is limited to the processes most relevant to the study of summer heat waves and serves as a basis for ongoing development which will address additional processes of the urban environment and lead to improvements to extend the utilization of the USM to other environments and conditions.

Structural adjustments in resprouting trees drive differences in post-fire transpiration.

PubMed

Nolan, Rachael H; Mitchell, Patrick J; Bradstock, Ross A; Lane, Patrick N J

2014-02-01

Following disturbance many woody species are capable of resprouting new foliage, resulting in a reduced leaf-to-sapwood area ratio and altered canopy structure. We hypothesized that such changes would promote adjustments in leaf physiology, resulting in higher rates of transpiration per unit leaf area, consistent with the mechanistic framework proposed by Whitehead et al. (Whitehead D, Jarvis PG, Waring RH (1984) Stomatal conductance, transpiration and resistance to water uptake in a Pinus sylvestris spacing experiment. Can J For Res 14:692-700). We tested this in Eucalyptus obliqua L'Hér following a wildfire by comparing trees with unburnt canopies with trees that had been subject to 100% canopy scorch and were recovering their leaf area via resprouting. In resprouting trees, foliage was distributed along the trunk and on lateral branches, resulting in shorter hydraulic path lengths. We evaluated measurements of whole-tree transpiration and structural and physiological traits expected to drive any changes in transpiration. We used these structural and physiological measurements to parameterize the Whitehead et al. equation, and found that the expected ratio of transpiration per unit leaf area between resprouting and unburnt trees was 3.41. This is similar to the observed ratio of transpiration per unit leaf area, measured from sapflow observations, which was 2.89 (i.e., resprouting trees had 188% higher transpiration per unit leaf area). Foliage at low heights (<2 m) was found to be significantly different to foliage in the tree crown (14-18 m) in a number of traits, including higher specific leaf area, midday leaf water potential and higher rates of stomatal conductance and photosynthesis. We conclude that these post-fire adjustments in resprouting trees help to drive increased stomatal conductance and hydraulic efficiency, promoting the rapid return of tree-scale transpiration towards pre-disturbance levels. These transient patterns in canopy transpiration have important implications for modelling stand-level water fluxes in forests capable of resprouting, which is frequently done on the basis of the leaf area index.

Photon Recollision Probability: a Useful Concept for Cross Scale Consistency Check between Leaf Area Index and Foliage Clumping Products

NASA Astrophysics Data System (ADS)

Pisek, J.

2017-12-01

Clumping index (CI) is the measure of foliage aggregation relative to a random distribution of leaves in space. CI is an important factor for the correct quantification of true leaf area index (LAI). Global and regional scale CI maps have been generated from various multi-angle sensors based on an empirical relationship with the normalized difference between hotspot and darkspot (NDHD) index (Chen et al., 2005). Ryu et al. (2011) suggested that accurate calculation of radiative transfer in a canopy, important for controlling gross primary productivity (GPP) and evapotranspiration (ET) (Baldocchi and Harley, 1995), should be possible by integrating CI with incoming solar irradiance and LAI from MODIS land and atmosphere products. It should be noted that MODIS LAI/FPAR product uses internal non-empirical, stochastic equations for parameterization of foliage clumping. This raises a question if integration of the MODIS LAI product with empirically-based CI maps does not introduce any inconsistencies. Here, the consistency is examined independently through the `recollision probability theory' or `p-theory' (Knyazikhin et al., 1998) along with raw LAI-2000/2200 Plant Canopy Analyzer (PCA) data from > 30 sites, surveyed across a range of vegetation types. The theory predicts that the amount of radiation scattered by a canopy should depend only on the wavelength and the spectrally invariant canopy structural parameter p. The parameter p is linked to the foliage clumping (Stenberg et al., 2016). Results indicate that integration of the MODIS LAI product with empirically-based CI maps is feasible. Importantly, for the first time it is shown that it is possible to obtain p values for any location solely from Earth Observation data. This is very relevant for future applications of photon recollision probability concept for global and local monitoring of vegetation using Earth Observation data.

Modelling the effect of wheat canopy architecture as affected by sowing density on Septoria tritici epidemics using a coupled epidemic–virtual plant model

PubMed Central

Baccar, Rim; Fournier, Christian; Dornbusch, Tino; Andrieu, Bruno; Gouache, David; Robert, Corinne

2011-01-01

Background and Aims The relationship between Septoria tritici, a splash-dispersed disease, and its host is complex because of the interactions between the dynamic plant architecture and the vertical progress of the disease. The aim of this study was to test the capacity of a coupled virtual wheat–Septoria tritici epidemic model (Septo3D) to simulate disease progress on the different leaf layers for contrasted sowing density treatments. Methods A field experiment was performed with winter wheat ‘Soissons’ grown at three contrasted densities. Plant architecture was characterized to parameterize the wheat model, and disease dynamic was monitored to compare with simulations. Three simulation scenarios, differing in the degree of detail with which plant variability of development was represented, were defined. Key Results Despite architectural differences between density treatments, few differences were found in disease progress; only the lower-density treatment resulted in a slightly higher rate of lesion development. Model predictions were consistent with field measurements but did not reproduce the higher rate of lesion progress in the low density. The canopy reconstruction scenario in which inter-plant variability was taken into account yielded the best agreement between measured and simulated epidemics. Simulations performed with the canopy represented by a population of the same average plant deviated strongly from the observations. Conclusions It was possible to compare the predicted and measured epidemics on detailed variables, supporting the hypothesis that the approach is able to provide new insights into the processes and plant traits that contribute to the epidemics. On the other hand, the complex and dynamic responses to sowing density made it difficult to test the model precisely and to disentangle the various aspects involved. This could be overcome by comparing more contrasted and/or simpler canopy architectures such as those resulting from quasi-isogenic lines differing by single architectural traits. PMID:21724656

Downscaling modelling system for multi-scale air quality forecasting

NASA Astrophysics Data System (ADS)

Nuterman, R.; Baklanov, A.; Mahura, A.; Amstrup, B.; Weismann, J.

2010-09-01

Urban modelling for real meteorological situations, in general, considers only a small part of the urban area in a micro-meteorological model, and urban heterogeneities outside a modelling domain affect micro-scale processes. Therefore, it is important to build a chain of models of different scales with nesting of higher resolution models into larger scale lower resolution models. Usually, the up-scaled city- or meso-scale models consider parameterisations of urban effects or statistical descriptions of the urban morphology, whereas the micro-scale (street canyon) models are obstacle-resolved and they consider a detailed geometry of the buildings and the urban canopy. The developed system consists of the meso-, urban- and street-scale models. First, it is the Numerical Weather Prediction (HIgh Resolution Limited Area Model) model combined with Atmospheric Chemistry Transport (the Comprehensive Air quality Model with extensions) model. Several levels of urban parameterisation are considered. They are chosen depending on selected scales and resolutions. For regional scale, the urban parameterisation is based on the roughness and flux corrections approach; for urban scale - building effects parameterisation. Modern methods of computational fluid dynamics allow solving environmental problems connected with atmospheric transport of pollutants within urban canopy in a presence of penetrable (vegetation) and impenetrable (buildings) obstacles. For local- and micro-scales nesting the Micro-scale Model for Urban Environment is applied. This is a comprehensive obstacle-resolved urban wind-flow and dispersion model based on the Reynolds averaged Navier-Stokes approach and several turbulent closures, i.e. k -ɛ linear eddy-viscosity model, k - ɛ non-linear eddy-viscosity model and Reynolds stress model. Boundary and initial conditions for the micro-scale model are used from the up-scaled models with corresponding interpolation conserving the mass. For the boundaries a kind of Dirichlet condition is chosen to provide the values based on interpolation from the coarse to the fine grid. When the roughness approach is changed to the obstacle-resolved one in the nested model, the interpolation procedure will increase the computational time (due to additional iterations) for meteorological/ chemical fields inside the urban sub-layer. In such situations, as a possible alternative, the perturbation approach can be applied. Here, the effects of main meteorological variables and chemical species are considered as a sum of two components: background (large-scale) values, described by the coarse-resolution model, and perturbations (micro-scale) features, obtained from the nested fine resolution model.

Retrieval of forest biomass for tropical deciduous mixed forest using ALOS PALSAR mosaic imagery and field plot data

NASA Astrophysics Data System (ADS)

Ningthoujam, Ramesh K.; Joshi, P. K.; Roy, P. S.

2018-07-01

Tropical forest is an important ecosystem rich in biodiversity and structural complexity with high woody biomass content. Longer wavelength radar data at L-band sensor provides improved forest biomass (AGB) information due to its higher penetration level and sensitivity to canopy structure. The study presents a regression based woody biomass estimation for tropical deciduous mixed forest dominated by Shorea robusta using ALOS PALSAR mosaic (HH, HV) and field data at the lower Himalayan belt of Northern India. For the purpose of understanding the scattering mechanisms at L-band from this forest type, Michigan Microwave Canopy Scattering model (MIMICS-I) was parameterized with field data to simulate backscatter across polarization and incidence range. Regression analysis between field measured forest biomass and L-band backscatter data from PALSAR mosaic show retrieval of woody biomass up to 100 Mg ha-1 with error between 92 and 94 Mg ha-1 and coefficient of determination (r2) between 0.53 and 0.55 for HH and HH + HV polarized channel at 0.25 ha resolution. This positive relationship could be due to strong volume scattering from ground/trunk interaction at HH-polarized while in combination with direct canopy scattering for HV-polarization at ALOS specific incidence angles as predicted by MIMICS-I model. This study has found that L-band SAR data from currently ALOS-1/-2 and upcoming joint NASA-ISRO SAR (NISAR) are suitable for mapping forest biomass ≤100 Mg ha-1 at 25 m resolution in far incidence range in dense deciduous mixed forest of Northern India.

Modeling Energy and Mass Fluxes Over a Vineyard Using the Acasa Model

NASA Astrophysics Data System (ADS)

Marras, S.; Bellucco, V.; Pyles, D.; Falk, M.; Sirca, C.; Duce, P.; Snyder, R. L.; Paw U, K.; Spano, D.

2012-12-01

Energy and mass fluxes are widely monitored over natural ecosystems by the Eddy Covariance (EC) towers within the FLUXNET monitoring network. Only a few studies focused on EC measurements over tree crops and vines, and there is a lack of information useful to parameterize crop and flux models over such systems. The aim of this study was to improve our knowledge about the performance of the land surface model ACASA (Advanced Canopy-Atmosphere-Soil Algorithm) in estimating energy, water, and carbon fluxes over a typical Mediterranean vineyard located in Southern Sardinia (Italy). ACASA estimates turbulent fluxes per 20 canopy layers (10 layers within and 10 above the canopy) and 15 soil layers, using third-order closure equations. CO2 fluxes are estimated using a combination of Ball-Berry and Farquhar equations. The model parameters derived from literature, from a previous work conducted in Tuscany (Italy) and from direct measurements collected in the experimental site of this study. An Eddy Covariance measurement tower was installed to continuously monitor sensible and latent heat, and CO2 fluxes, in conjunction with a net radiometer, and soil heat flux plates from June 2009. A meteorological station was also set up for ancillary measurements. Model performance was evaluated by RMSE and linear regression statistics. Results for the energy balance components and CO2 exchanges will be presented. Detailed analysis was devoted to evaluate the model ability in estimating the vineyard evapotranspiration. This term of the energy balance is, in fact, important for farmers since they are mainly interested in quantify crop water requirements for a better irrigation management.

Carbon dioxide fluxes dynamics comparison in Moscow urban forest and adjacent urban areas

NASA Astrophysics Data System (ADS)

Yaroslavtsev, Alexis; Meshalkina, Joulia; Mazirov, Ilya; Vasenev, Ivan

2017-04-01

In the beginning of the 2014 in northern district of Moscow was installed eddy covariance tower on the edge of Timiryazevskiy urban forest and Timiryazevskiy district of Moscow. Tower 34m high was constructed inside the territory of LOD (Lesnaya Opytnaya Dacha) experimental station in the south-eastern part of the forest. Main tree species of urban forest and neighboring urban areas are Acer Plantanoides, Tilia cordata, Betula pendula, Quercus robur, Pinus sylvestris. Forest itself is mixed with some small plots dominated only by deciduous or coniferous species, whether trees in urban areas was mainly deciduous. Mean canopy height is about 30m. in both forest and urban areas. The soil cover of the studied sections is represented by sod-podzolic soils with different degree of development of the humus horizon. All soils have well-developed profile of sod-podzolic soil with low power litter (only in forest area) and developed humus-accumulative horizon with high humus content (3,24%) Carbon dioxide daily fluxes from investigated area was calculated for six months of 2014 (from April till October) utilizing eddy covariance method. Most (90%) of fluxes footprints was no longer than 500m for all wind directions during the time of monitoring. Forest in 500m radius around tower is a zone of active recreation with several roads and wide path network. On the other hand closest to tower urban area characterized by a low-rise buildings (in most cases no more than 5 floors) which are mainly administration ones and have wide green areas around them very few roads and low traffic. As a result difference in calculated fluxes was not so dramatic, as it was expected. Diurnal carbon dioxide fluxes dynamics was pretty the same for all months except August, due to long period without precipitation and higher soil moisture under the forest canopy. Estimated daily fluxes values was higher in forest areas for the whole period of investigation, except August, and ranged from -2 to 8 g C CO2 d-1 m-2 with mean about 2,5 g C CO2 d-1 m-2 .

Estimating urban trees and carbon stock potentials for mitigating climate change in Lagos: Case of Ikeja Government Reserved Area (GRA)

NASA Astrophysics Data System (ADS)

Elias, P. O.; Faderin, A.

2014-12-01

Urban trees are a component of the urban infrastructure which offers diverse services including environmental, aesthetic and economic. The accumulation of carbon in the atmosphere resulting from the indiscriminate distribution of human populations and urban activities with the unsustainable consumption of natural resources contributes to global environmental change especially in coastal cities like Lagos. Carbon stocks and sequestration by urban trees are increasingly recognized to play significant roles for mitigating climate change. This paper focuses on the estimation of carbon stock and sequestration through biomass estimation and quantification in Ikeja GRA, Lagos. Ikeja possesses a characteristic feature as a microcosm of Lagos due to the wide range of land uses. A canopy assessment of tree population was carried out using itree canopy software. A GPS survey was used to collect an inventory of all trees showing their location, spatial distribution and other attributes. The analysis of the carbon storage and sequestration potential of both actual and potential tree planting sites involved biomass estimations from tree allometry equations. Trees were identified at species level and measurements of their dendrometric values were recorded and integrated into the GIS database to estimate biomass of trees and carbon storage. The trees in the study area were estimated to have a biomass of 441.9 mg and carbon storage of 221.395 kg/tree. By considering the potential tree planting sites the estimated carbon stored increased to 11,352.73 kg. Carbon sequestration value in the study area was found to be 1.6790 tonnes for the existing trees and 40.707 tonnes for the potential tree planting sites (PTPS). The estimation of carbon storage and sequestration values of trees are important incentives for carbon accounting/footprints and monitoring of climate change mitigation which has implications for evaluation and monitoring of urban ecosystem.

Modelling of surface fluxes and Urban Boundary Layer over an old mediterannean city core

NASA Astrophysics Data System (ADS)

Lemonsu, A.; Masson, V.; Grimmond, Cs. B.

2003-04-01

In the frameworks of the UBL(Urban Boundary Layer)-ESCOMPTE campaign, the Town Energy Balance (TEB) model was run in off-line mode for Marseille. TEB's performance is evaluated with observations of surface temperatures and surface energy balance fluxes collected during the campaign. Parameterization improvements allow to better represent the energy exchanges between the air inside the canyon and the atmosphere above the roof level. Then, high resolution Méso-NH simulations are done to study the 3-D structure and the evolution of the Urban Boundary Layer (UBL) over Marseille. Will will give a special attention to the impact of the seabord effects (sea-breeze circulation) on the UBL.

An Improved Simulation of the Diurnally Varying Street Canyon Flow

NASA Astrophysics Data System (ADS)

Yaghoobian, Neda; Kleissl, Jan; Paw U, Kyaw Tha

2012-11-01

The impact of diurnal variation of temperature distribution over building and ground surfaces on the wind flow and scalar transport in street canyons is numerically investigated using the PArallelized LES Model (PALM). The Temperature of Urban Facets Indoor-Outdoor Building Energy Simulator (TUF-IOBES) is used for predicting urban surface heat fluxes as boundary conditions for a modified version of PALM. TUF-IOBES dynamically simulates indoor and outdoor building surface temperatures and heat fluxes in an urban area taking into account weather conditions, indoor heat sources, building and urban material properties, composition of the building envelope (e.g. windows, insulation), and HVAC equipment. Temperature (and heat flux) distribution over urban surfaces of the 3-D raster-type geometry of TUF-IOBES makes it possible to provide realistic, high resolution boundary conditions for the numerical simulation of flow and scalar transport in an urban canopy. Compared to some previous analyses using uniformly distributed thermal forcing associated with urban surfaces, the present analysis shows that resolving non-uniform thermal forcings can provide more detailed and realistic patterns of the local air flow and pollutant dispersion in urban canyons.

Modeling the formamtion and aging of secondary organic aerosols in Los Angeles during CalNex 2010

EPA Science Inventory

Four different literature parameterizations for the formation and evolution of urban secondary organic aerosol (SOA) frequently used in 3-D models are evaluated using a 0-D box model representing the Los Angeles metropolitan region during the California Research at the Nexus of A...

Wintertime ozone fluxes and profiles above a subalpine spruce-fir forest

Treesearch

Karl Zeller

2000-01-01

High rural concentrations of ozone (O3) are thought to be stratospheric in origin, advected from upwind urban sources, or photochemically generated locally by natural trace gas emissions. Ozone is known to be transported vertically downward from the above-canopy atmospheric surface layer and destroyed within stomata or on other biological and mineral surfaces. However...

Potential energy savings in buildings by an urban tree planting programme in California

Treesearch

E.G. McPherson; J.R. Simpson

2003-01-01

Tree canopy cover data from aerial photographs and building energy simulations were applied to estimate energy savings from existing trees and new plantings in California. There are approximately 177.3 million energy-conserving trees in California communities and 241.6 million empty planting sites. Existing trees are projected to reduce annual air conditioning energy...

Canopy decline assessment in American elm after inoculation with different doses of Ophiostoma ulmi and O. novo-ulmi

Treesearch

Charles E. Flower; James M. Slavicek; Dale Lesser; Steven Eshita; Cornelia C. Pinchot

2017-01-01

Restoration of American elm (Ulmus americana L.) in natural and urban landscapes necessitates the development of new selections that not only exhibit Dutch elm disease (DED, caused by the fungal pathogen Ophiostoma novo-ulmi and O. ulmi) tolerance, but also an increase the genetic variability of tolerant...

First results from the International Urban Energy Balance Model Comparison: Model Complexity

NASA Astrophysics Data System (ADS)

Blackett, M.; Grimmond, S.; Best, M.

2009-04-01

A great variety of urban energy balance models has been developed. These vary in complexity from simple schemes that represent the city as a slab, through those which model various facets (i.e. road, walls and roof) to more complex urban forms (including street canyons with intersections) and features (such as vegetation cover and anthropogenic heat fluxes). Some schemes also incorporate detailed representations of momentum and energy fluxes distributed throughout various layers of the urban canopy layer. The models each differ in the parameters they require to describe the site and the in demands they make on computational processing power. Many of these models have been evaluated using observational datasets but to date, no controlled comparisons have been conducted. Urban surface energy balance models provide a means to predict the energy exchange processes which influence factors such as urban temperature, humidity, atmospheric stability and winds. These all need to be modelled accurately to capture features such as the urban heat island effect and to provide key information for dispersion and air quality modelling. A comparison of the various models available will assist in improving current and future models and will assist in formulating research priorities for future observational campaigns within urban areas. In this presentation we will summarise the initial results of this international urban energy balance model comparison. In particular, the relative performance of the models involved will be compared based on their degree of complexity. These results will inform us on ways in which we can improve the modelling of air quality within, and climate impacts of, global megacities. The methodology employed in conducting this comparison followed that used in PILPS (the Project for Intercomparison of Land-Surface Parameterization Schemes) which is also endorsed by the GEWEX Global Land Atmosphere System Study (GLASS) panel. In all cases, models were run offline to ensure no feedback to larger scale conditions within the modelling domain. Initially, participants were issued with just forcing data from an unknown urban site (termed "Alpha"); in subsequent stages, further details of the site were provided. Results from each stage, for each participating model, were then compared using a variety of statistical and graphical techniques. * The EGU2009-5713 Team: C.S.B. Grimmond1, M. Blackett1, M. Best2 and J. Barlow3and J.-J. Baik4, S. Belcher3, S. Bohnenstengel3, I. Calmet5, F. Chen6, A. Dandou7, K. Fortuniak8, M. Gouvea1, R. Hamdi9, M. Hendry2, H. Kondo10, S. Krayenhoff11, S. H. Lee4, T. Loridan1, A. Martilli12, S. Miao13, K. Oleson6, G. Pigeon14, A. Porson2,3, F. Salamanca12, L. Shashua-Bar15, G.-J. Steeneveld16, M. Tombrou7, J. Voogt17, N. Zhang18. 1King's College London, UK, 2UK Met Office, UK, 3University of Reading, UK, 4Seoul National University, Korea, 5Ecole Centrale de Nantes, France, 6National Center for Atmospheric Research, USA, 7University of Athens, Greece, 8University of Ł ódź , Poland, 9Royal Meteorological Institute, Belgium, 10National Institute of Advanced Industrial Science and Technology, Japan, 11University of British Columbia, Canada, 12CIEMAT, Spain, 13IUM, CMA, China, 14Meteo France, France, 15Ben Gurion University, Israel, 16Wageningen University, Netherlands, 17University of Western Ontario, Canada, 18Nanjing University, China.

Nowhere safe? Exploring the influence of urbanization across mainland and insular seashores in continental Portugal and the Azorean Archipelago.

PubMed

Bertocci, Iacopo; Arenas, Francisco; Cacabelos, Eva; Martins, Gustavo M; Seabra, Maria I; Álvaro, Nuno V; Fernandes, Joana N; Gaião, Raquel; Mamede, Nuno; Mulas, Martina; Neto, Ana I

2017-01-30

Differences in the structure and functioning of intensively urbanized vs. less human-affected systems are reported, but such evidence is available for a much larger extent in terrestrial than in marine systems. We examined the hypotheses that (i) urbanization was associated to different patterns of variation of intertidal assemblages between urban and extra-urban environments; (ii) such patterns were consistent across mainland and insular systems, spatial scales from 10scm to 100skm, and a three months period. Several trends emerged: (i) a more homogeneous distribution of most algal groups in the urban compared to the extra-urban condition and the opposite pattern of most invertebrates; (ii) smaller/larger variances of most organisms where these were, respectively, less/more abundant; (iii) largest variability of most response variables at small scale; (iv) no facilitation of invasive species by urbanization and larger cover of canopy-forming algae in the insular extra-urban condition. Present findings confirm the acknowledged notion that future management strategies will require to include representative assemblages and their relevant scales of variation associated to urbanization gradients on both the mainland and the islands. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization and Modeling of Atmospheric Flow Within and Above Plant Canopies

NASA Astrophysics Data System (ADS)

Souza Freire Grion, Livia

The turbulent flow within and above plant canopies is responsible for the exchange of momentum, heat, gases and particles between vegetation and the atmosphere. Turbulence is also responsible for the mixing of air inside the canopy, playing an important role in chemical and biophysical processes occurring in the plants' environment. In the last fifty years, research has significantly advanced the understanding of and ability to model the flow field within and above the canopy, but important issues remain unsolved. In this work, we focus on (i) the estimation of turbulent mixing timescales within the canopy from field data; and (ii) the development of new computationally efficient modeling approaches for the coupled canopy-atmosphere flow field. The turbulent mixing timescale represents how quickly turbulence creates a well-mixed environment within the canopy. When the mixing timescale is much smaller than the timescale of other relevant processes (e.g. chemical reactions, deposition), the system can be assumed to be well-mixed and detailed modeling of turbulence is not critical to predict the system evolution. Conversely, if the mixing timescale is comparable or larger than the other timescales, turbulence becomes a controlling factor for the concentration of the variables involved; hence, turbulence needs to be taken into account when studying and modeling such processes. In this work, we used a combination of ozone concentration and high-frequency velocity data measured within and above the canopy in the Amazon rainforest to characterize turbulent mixing. The eddy diffusivity parameter (used as a proxy for mixing efficiency) was applied in a simple theoretical model of one-dimensional diffusion, providing an estimate of turbulent mixing timescales as a function of height within the canopy and time-of-day. Results showed that, during the day, the Amazon rainforest is characterized by well-mixed conditions with mixing timescales smaller than thirty minutes in the upper-half of the canopy, and partially mixed conditions in the lower half of the canopy. During the night, most of the canopy (except for the upper 20%) is either partially or poorly mixed, resulting in mixing timescales of up to several hours. For the specific case of ozone, the mixing timescales observed during the day are much lower than the chemical and deposition timescales, whereas chemical processes and turbulence have comparable timescales during the night. In addition, the high day-to-day variability in mixing conditions and the fast increase in mixing during the morning transition period indicate that turbulence within the canopy needs to be properly investigated and modeled in many studies involving plant-atmosphere interactions. Motivated by the findings described above, this work proposes and tests a new approach for modeling canopy flows. Typically, vertical profiles of flow statistics are needed to represent canopy-atmosphere exchanges in chemical and biophysical processes happening within the canopy. Current single-column models provide only steady-state (equilibrium) profiles, and rely on closure assumptions that do not represent the dominant non-local turbulent fluxes present in canopy flows. We overcome these issues by adapting the one-dimensional turbulent (ODT) model to represent atmospheric flows from the ground up to the top of the atmospheric boundary layer (ABL). The ODT model numerically resolves the one-dimensional diffusion equation along a vertical line (representing a horizontally homogeneous ABL column), and the presence of three-dimensional turbulence is added through the effect of stochastic eddies. Simulations of ABL without canopy were performed for different atmospheric stabilities and a diurnal cycle, to test the capabilities of this modeling approach in representing unsteady flows with strong non-local transport. In addition, four different types of canopies were simulated, one of them including the transport of scalar with a point source located inside the canopy. The comparison of all simulations with theory and field data provided satisfactory results. The main advantages of using ODT compared to typical 1D canopy-flow models are the ability to represent the coupled canopy-ABL flow with one single modeling approach, the presence of non-local turbulent fluxes, the ability to simulate transient conditions, the straightforward representation of multiple scalar fields, and the presence of only one adjustable parameter (as opposed to the several adjustable constants and boundary conditions needed for other modeling approaches). The results obtained with ODT as a stand-alone model motivated its use as a surface parameterization for Large-Eddy Simulation (LES). In this two-way coupling between LES and ODT, the former is used to simulate the ABL in a case where a canopy is present but cannot be resolved by the LES (i.e., the LES first vertical grid point is above the canopy). ODT is used to represent the flow field between the ground and the first LES grid point, including the region within and just above the canopy. In this work, we tested the ODT-LES model for three different types of canopies and obtained promising results. Although more work is needed in order to improve first and second-order statistics within the canopy (i.e. in the ODT domain), the results obtained for the flow statistics in the LES domain and for the third order statistics in the ODT domain demonstrate that the ODT-LES model is capable of capturing some important features of the canopy-atmosphere interaction. This new surface superparameterization approach using ODT provides a new alternative for simulations that require complex interactions between the flow field and near-surface processes (e.g. sand and snow drift, waves over water surfaces) and can potentially be extended to other large-scale models, such as mesoscale and global circulation models.

Impacts of Realistic Urban Heating. Part II: Air Quality and City Breathability

NASA Astrophysics Data System (ADS)

Nazarian, Negin; Martilli, Alberto; Norford, Leslie; Kleissl, Jan

2018-03-01

Urban morphology and inter-building shadowing result in a non-uniform distribution of surface heating in urban areas, which can significantly modify the urban flow and thermal field. In Part I, we found that in an idealized three-dimensional urban array, the spatial distribution of the thermal field is correlated with the orientation of surface heating with respect to the wind direction (i.e. leeward or windward heating), while the dispersion field changes more strongly with the vertical temperature gradient in the street canyon. Here, we evaluate these results more closely and translate them into metrics of "city breathability," with large-eddy simulations coupled with an urban energy-balance model employed for this purpose. First, we quantify breathability by, (i) calculating the pollutant concentration at the pedestrian level (horizontal plane at z≈ 1.5 -2 m) and averaged over the canopy, and (ii) examining the air exchange rate at the horizontal and vertical ventilating faces of the canyon, such that the in-canopy pollutant advection is distinguished from the vertical removal of pollution. Next, we quantify the change in breathability metrics as a function of previously defined buoyancy parameters, horizontal and vertical Richardson numbers (Ri_h and Ri_v , respectively), which characterize realistic surface heating. We find that, unlike the analysis of airflow and thermal fields, consideration of the realistic heating distribution is not crucial in the analysis of city breathability, as the pollutant concentration is mainly correlated with the vertical temperature gradient (Ri_v ) as opposed to the horizontal (Ri_h ) or bulk (Ri_b ) thermal forcing. Additionally, we observe that, due to the formation of the primary vortex, the air exchange rate at the roof level (the horizontal ventilating faces of the building canyon) is dominated by the mean flow. Lastly, since Ri_h and Ri_v depend on the meteorological factors (ambient air temperature, wind speed, and wind direction) as well as urban design parameters (such as surface albedo), we propose a methodology for mapping overall outdoor ventilation and city breathability using this characterization method. This methodology helps identify the effects of design on urban microclimate, and ultimately informs urban designers and architects of the impact of their design on air quality, human health, and comfort.

Sources and Characterization of Submicron Aerosols in a Rural Forest During the PROPHET-AMOS 2016 Campaign

NASA Astrophysics Data System (ADS)

Bui, A. T.; Wallace, H. W., IV; Alvarez, S. L.; Erickson, M.; Alwe, H. D.; May, N.; Cook, R.; Connor, M.; Slade, J. H., Jr.; Shi, Q.; Kavassalis, S.; Tyndall, G. S.; Shepson, P. B.; Pratt, K.; Ault, A. P.; Millet, D. B.; Murphy, J. G.; Usenko, S.; Sheesley, R. J.; Flynn, J. H., III; Griffin, R. J.; Wang, W.

2017-12-01

Forests are a rich source of biogenic volatile organic compounds (BVOCs). Oxidation of BVOCs can result in the formation of secondary organic aerosol (SOA) and in the presence of NOx (NO+NO2) produce organic nitrate-containing particles. However, the distribution of both BVOCs and oxidants can be dramatically altered by the physical barriers provided by a forest canopy. Global models currently neglect the effect of these canopies on SOA formation in forested regions. In this work, we characterize non-refractory submicron aerosol (NR-PM1) using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) during the 2016 Program on Oxidants: Photochemistry, Emissions, and Transport-Atmospheric Measurements of Oxidants in Summer (PROPHET-AMOS) campaign. This site is located in a rural forest in northern Michigan and features a tower that allowed for both above and below canopy measurements. Our results indicate that organic aerosols (OA) account for a substantial portion of the NR-PM1 measured at this site. Organic nitrate aerosol can contribute up to 18% of the total OA and an average of 75% of the total measured nitrate aerosol. Episodes of above- and below-canopy NR-PM1 concentration differences indicate that above-canopy OA concentrations can be up to 40% greater than below-canopy, which represents an increase of up to 1.5 µg/m3. Organic fragment ions such as CxHy, CxHyOz, and CxHyO1 contribute to enhanced above-canopy OA concentrations. Positive matrix factorization analysis of the high-resolution OA mass spectra identified three SOA factors: low volatility oxygenated OA (LVOOA), isoprene-derived OOA (ISOOA), and oxygenated organic aerosol. Analysis of air mass backward trajectories and correlations with external data indicate that LVOOA correlates well with sulfate and aged, urban-influenced air masses, whereas ISOOA correlates well with isoprene SOA tracers and air masses originating from semi-remote areas. Our results indicate that the OA at this site is dominated by SOA formation and that vertical differences in OA can exist in the presence of a forest canopy. Results from this work have important implications in understanding the role that canopies play in SOA formation and provide useful data to help accurately validate biosphere-atmosphere exchange models.

The contribution of urbanization to recent extreme heat events and white roof mitigation strategy in the Beijing-Tianjin-Hebei metropolitan area

NASA Astrophysics Data System (ADS)

Wang, Mingna

2015-04-01

The UHI effect can aggravate summertime heat waves and strongly influence human comfort and health, leading to greater mortality in metropolitan areas. Many geo-engineering technological strategies have been proposed to mitigate climate warming, and for the UHI, increasing the albedo of artificial urban surfaces (rooftops or pavements) has been considered a lucrative and effective way to cool cities. The objective of this work is to quantify the contribution of urbanization to recent extreme heat events of the early 21st century in the Beijing-Tianjin-Hebei metropolitan area, using the mesoscale WRF model coupled with a single urban canopy model and actual urban land cover datasets. This work also investigates a simulation of the regional effects of white roof technology by increasing the albedo of urban areas in the urban canopy model to mitigate the urban heat island, especially in extreme heat waves. The results show that urban land use characteristics that have evolved over the past ~20 years in the Beijing-Tianjin-Hebei metropolitan area have had a significant impact on the extreme temperatures occurring during extreme heat events. Simulations show that new urban development has caused an intensification and expansion of the areas experiencing extreme heat waves with an average increase in temperature of approximately 0.60°C. This change is most obvious at night with an increase up to 0.95°C, for which the total contribution of anthropogenic heat is 34%. We also simulate the effects of geo-engineering strategies increasing the albedo of urban roofs. White roofs reflect a large fraction of incoming sunlight in the daytime, which reduced the net radiation so that the roof surface keep at a lower temperature than regular solar-absorptive roofs. Urban net radiation decreases by approximately 200 W m-2 at local noon because of high solar reflectance of white roofs, which cools the daytime urban temperature afer sunrise, with the largest decrease of almost -0.80°C at local noon. Moreover, the nighttime temperature also shows slightly cooler, approximately 0.2°C, because there is still considerable heat which is stored in the daytime released from urban surfaces at night. The results also suggest that increasing the albedo of urban roofs can reduce the urban mean temperature by approximately 0.51°C during summer extreme heat events. In urban areas, white roofs can counter 80% of the heat wave results from urban sprawl during the last 20 years. These results suggest that increasing the albedo of roofs in the Beijing-Tianjin-Hebei metropolitan area is an effective way of countering some hazards of heat waves. Using a regional climate model, we proposed that white roofs may be an effective strategy to complement urban heat wave mitigation efforts as a way of further slowing the rate of global temperature increase in response to continued greenhouse gas emissions.

Automatic extraction of road features in urban environments using dense ALS data

NASA Astrophysics Data System (ADS)

Soilán, Mario; Truong-Hong, Linh; Riveiro, Belén; Laefer, Debra

2018-02-01

This paper describes a methodology that automatically extracts semantic information from urban ALS data for urban parameterization and road network definition. First, building façades are segmented from the ground surface by combining knowledge-based information with both voxel and raster data. Next, heuristic rules and unsupervised learning are applied to the ground surface data to distinguish sidewalk and pavement points as a means for curb detection. Then radiometric information was employed for road marking extraction. Using high-density ALS data from Dublin, Ireland, this fully automatic workflow was able to generate a F-score close to 95% for pavement and sidewalk identification with a resolution of 20 cm and better than 80% for road marking detection.

Implementation of a subcanopy solar radiation model on a forested headwater basin in the Southern Appalachians to estimate riparian canopy density and stream insolation for stream temperature models

NASA Astrophysics Data System (ADS)

Belica, L.; Petras, V.; Iiames, J. S., Jr.; Caldwell, P.; Mitasova, H.; Nelson, S. A. C.

2016-12-01

Water temperature is a key aspect of water quality and understanding how the thermal regimes of forested headwater streams may change in response to climatic and land cover changes is increasingly important to scientists and resource managers. In recent years, the forested mountain watersheds of the Southeastern U.S. have experienced changing climatic patterns as well as the loss of a keystone riparian tree species and anticipated hydrologic responses include lower summer stream flows and decreased stream shading. Solar radiation is the main source of thermal energy to streams and a key parameter in heat-budget models of stream temperature; a decrease in flow volume combined with a reduction in stream shading during summer have the potential to increase stream temperatures. The high spatial variability of forest canopies and the high spatio-temporal variability in sky conditions make estimating the solar radiation reaching small forested headwater streams difficult. The Subcanopy Solar Radiation Model (SSR) (Bode et al. 2014) is a GIS model that generates high resolution, spatially explicit estimates of solar radiation by incorporating topographic and vegetative shading with a light penetration index derived from leaf-on airborne LIDAR data. To evaluate the potential of the SSR model to provide estimates of stream insolation to parameterize heat-budget models, it was applied to the Coweeta Basin in the Southern Appalachians using airborne LIDAR (NCALM 2009, 1m resolution). The LIDAR derived canopy characteristics were compared to current hyperspectral images of the canopy for changes and the SSR estimates of solar radiation were compared with pyranometer measurements of solar radiation at several subcanopy sites during the summer of 2016. Preliminary results indicate the SSR model was effective in identifying variations in canopy density and light penetration, especially in areas associated with road and stream corridors and tree mortality. Current LIDAR data and more solar radiation measurements are needed to fully validate the accuracy of the SSR model in Southern Appalachian forests, but initial results suggest the high resolution, spatially explicit estimates of solar radiation can improve solar radiation parameter estimates in deterministic models of stream temperature in forested landscapes.

Branching out to residential lands: Missions and strategies of five tree distribution programs in the U.S.

Treesearch

Vi D. Nguyen; Lara A. Roman; Dexter H. Locke; Sarah K. Mincey; Jessica R. Sanders; Erica Smith Fichman; Mike Duran-Mitchell; Sarah Lumban Tobing

2017-01-01

Residential lands constitute a major component of existing and possible tree canopy in many cities in the United States. To expand the urban forest on these lands, some municipalities and nonprofit organizations have launched residential yard tree distribution programs, also known as tree giveaway programs. This paper describes the operations of five tree distribution...

Evaluation of the National Land Database for Hydrologic Applications in Urban And Suburban Baltimore, Maryland

Treesearch

Monica Lipscomb Smith; Weiqi Zhou; Mary Cadenasso; J. Morgan Grove; Lawrence Band

2010-01-01

We compared the National Land Cover Database (NLCD) 2001 land cover, impervious, and canopy data products to land cover data derived from 0.6-m resolution three-band digital imagery and ancillary data. We conducted this comparison at the 1 km2, 9 km2, and gauged watershed scales within the Baltimore Ecosystem Study to...

Measurements of upward turbulent ozone fluxes above a subalpine spruce-fir forest

Treesearch

Karl Zeller; Ted Hehn

1996-01-01

High rural concentrations of ozone (O3) are thought to be either stratospheric in origin, advected from upwind urban sources, or photochemically generated locally as a result of natural trace gas emissions. Ozone is known to be transported vertically downward from the above-canopy atmospheric surface layer and destroyed within stomata or on other biological and mineral...

Cryptic indirect effects of exurban edges on a woodland community

Treesearch

R. J. Warren; S. M. Pearson; S. Henry; K. Rossouw; J. P. Love; M. J. Olejniczak; Katherine Elliott; M. A. Bradford

2015-01-01

Exurban development (e.g., second homes) in woodlands spreads urban land use impacts beyond suburbs, but because exurban developments often retain many components of original ecosystem structure—such as a forest canopy rather than open lawn—their ecological impacts may be underestimated. Changes in seed-dispersing ant behavior prompted by exurban land use,...

Tree and impervious cover in the United States

Treesearch

David J. Nowak; Eric J. Greenfield

2012-01-01

Using aerial photograph interpretation of circa 2005 imagery, percent tree canopy and impervious surface cover in the conterminous United States are estimated at 34.2% (standard error (SE) = 0.2%) and 2.4% (SE = 0.1%), respectively. Within urban/community areas, percent tree cover (35.1%, SE = 0.4%) is similar to the national value, but percent impervious cover is...

Assembling a biogenic hydrocarbon emissions inventory for the SCOS97-NARSTO modeling domain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin, M.T.; Winer, A.M.; Karlik, J.

1998-12-31

To assist in developing ozone control strategies for Southern California, the California Air Resources Board is developing a biogenic hydrocarbon (BHC) emissions inventory model for the SCOS97-NARSTO domain. The basis for this bottom-up model is SCOS97-NARSTO-specific landuse and landcover maps, leafmass constants, and BHC emission rates. In urban areas, landuse maps developed by the Southern California Association of Governments, San Diego Association of Governments, and other local governments are used while in natural areas, landcover and plant community databases produced by the GAP Analysis Project (GAP) are employed. Plant identities and canopy volumes for species in each landuse and landcovermore » category are based on the most recent botanical field survey data. Where possible, experimentally determined leafmass constant and BHC emission rate measurements reported in the literature are used or, for those species where experimental data are not available, values are assigned based on taxonomic methods. A geographic information system is being used to integrate these databases, as well as the most recent environmental correction algorithms and canopy shading factors, to produce a spatially- and temporally-resolved BHC emission inventory suitable for input into the Urban Airshed Model.« less

Trees Grow on Money: Urban Tree Canopy Cover and Environmental Justice

PubMed Central

Schwarz, Kirsten; Fragkias, Michail; Boone, Christopher G.; Zhou, Weiqi; McHale, Melissa; Grove, J. Morgan; O’Neil-Dunne, Jarlath; McFadden, Joseph P.; Buckley, Geoffrey L.; Childers, Dan; Ogden, Laura; Pincetl, Stephanie; Pataki, Diane; Whitmer, Ali; Cadenasso, Mary L.

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman’s correlation, ordinary least squares regression (OLS), and a spatial autoregressive model (SAR). Across all cities there is a strong positive correlation between UTC cover and median household income. Negative correlations between race and UTC cover exist in bivariate models for some cities, but they are generally not observed using multivariate regressions that include additional variables on income, education, and housing age. SAR models result in higher r-square values compared to the OLS models across all cities, suggesting that spatial autocorrelation is an important feature of our data. Similarities among cities can be found based on shared characteristics of climate, race/ethnicity, and size. Our findings suggest that a suite of variables, including income, contribute to the distribution of UTC cover. These findings can help target simultaneous strategies for UTC goals and environmental justice concerns. PMID:25830303

Removal of Polycyclic Aromatic Hydrocarbons from Precipitation in an Urban Forest of Guangzhou, South China.

PubMed

Chen, Bufeng; Pei, Nancai; Huang, Junbiao; Liu, Shuguang; Zhang, Na; Xiao, Yihua; Pan, Yongjun

2015-08-01

Polycyclic aromatic hydrocarbon (PAH) concentrations and fluxes were measured monthly in situ from rain events in an urban forest in the megapolitan city Guangzhou, China, to investigate impacts of forest canopy and soils on PAHs. Mean Σ9-PAH concentrations were 107.5, 101.6, 106.3, 107.1 and 42.4 ng L(-1) in precipitation, throughfall, seepage water at the 30 and 60 cm soil depth, and runoff, respectively, indicating a great decrease in the form of runoff. Meanwhile, annual fluxes of total PAHs decreased from precipitation (205.9 µg m(-2) year(-1)), to throughfall (156.3 µg m(-2) year(-1)), and to seepage water (65.3 µg m(-2) year(-1) at 30-cm soil depth and 7.5 µg m(-2) year(-1) at 60-cm soil depth), but increased in runoff (34.1 µg m(-2) year(-1)). When compared to precipitation, PAH fluxes decreased by 83.4% in runoff, with 29% contributed by forest canopy and 71% by soils. Soil biodegradation explained 18.2% of PAH reduction by the surface soil layer and 34.6% by the middle soil layer.

Linking vegetation structure, function and physiology through spectroscopic remote sensing

NASA Astrophysics Data System (ADS)

Serbin, S.; Singh, A.; Couture, J. J.; Shiklomanov, A. N.; Rogers, A.; Desai, A. R.; Kruger, E. L.; Townsend, P. A.

2015-12-01

Terrestrial ecosystem process models require detailed information on ecosystem states and canopy properties to properly simulate the fluxes of carbon (C), water and energy from the land to the atmosphere and assess the vulnerability of ecosystems to perturbations. Current models fail to adequately capture the magnitude, spatial variation, and seasonality of terrestrial C uptake and storage, leading to significant uncertainties in the size and fate of the terrestrial C sink. By and large, these parameter and process uncertainties arise from inadequate spatial and temporal representation of plant traits, vegetation structure, and functioning. With increases in computational power and changes to model architecture and approaches, it is now possible for models to leverage detailed, data rich and spatially explicit descriptions of ecosystems to inform parameter distributions and trait tradeoffs. In this regard, spectroscopy and imaging spectroscopy data have been shown to be invaluable observational datasets to capture broad-scale spatial and, eventually, temporal dynamics in important vegetation properties. We illustrate the linkage of plant traits and spectral observations to supply key data constraints for model parameterization. These constraints can come either in the form of the raw spectroscopic data (reflectance, absorbtance) or physiological traits derived from spectroscopy. In this presentation we highlight our ongoing work to build ecological scaling relationships between critical vegetation characteristics and optical properties across diverse and complex canopies, including temperate broadleaf and conifer forests, Mediterranean vegetation, Arctic systems, and agriculture. We focus on work at the leaf, stand, and landscape scales, illustrating the importance of capturing the underlying variability in a range of parameters (including vertical variation within canopies) to enable more efficient scaling of traits related to functional diversity of ecosystems.

Spatio-Temporal Variability of Gross Rainfall, Throughfall and Stemflow in a Non-native Hawaiian Forest

NASA Astrophysics Data System (ADS)

Fares, A.; Safeeq, M.; Fares, S.

2011-12-01

Information on partitioning of gross rainfall in non-native trees in Hawaiian forests is limited. In this study, measurements of gross rainfall (PG), throughfall (TF), and stemflow (SF) were made at three locations in the upper Mākaha valley watershed to perform canopy water balance and parameterize Gash analytical model. The three selected locations are dominated by Strawberry guava (Psidium cattleianum), Christmas berry (Schinus terebinthifolius), Java plum (Syzygium cumini), and Coffee (Coffea Arabica) trees. Mean TF expressed as percentage of PG was the lowest (43.32%) under Strawberry guava and the highest (56.47%) under a mixture of Christmas berry, Strawberry guava, and Java plum. However, measured SF was the highest (33.9%) for Strawberry guava and lowest (3.6%) under the mixture of Christmas berry, Strawberry guava, and Java plum. The highest SF under Strawberry guava can be attributed to its smooth bark and steep branching and could have been the reason behind lowest TF. The mean observed interception losses varied between 23% under Strawberry guava and 45% for the site dominated by Coffee. Estimated mean free TF coefficients varied from 0.34 to 0.44, while the mean canopy storage capacity varied from 0.89 to 1.94 mm. The mean SF partitioning coefficient ranged from 0.05 to 0.37. The estimated canopy storage and trunk storage (P't) varied from 4.6 to 5.7 mm and 1.47 to 3.72 mm, respectively. Trees with nearly vertical branches and smooth bark (i.e. Strawberry Guava) resulted in smaller value of trunk storage. The analytical Gash's model for rainfall interception was successfully applied and its simulated results agreed reasonably well with observed data.

Development of a coupled wave-flow-vegetation interaction model

USGS Publications Warehouse

Beudin, Alexis; Kalra, Tarandeep S.; Ganju, Neil K.; Warner, John C.

2017-01-01

Emergent and submerged vegetation can significantly affect coastal hydrodynamics. However, most deterministic numerical models do not take into account their influence on currents, waves, and turbulence. In this paper, we describe the implementation of a wave-flow-vegetation module into a Coupled-Ocean-Atmosphere-Wave-Sediment Transport (COAWST) modeling system that includes a flow model (ROMS) and a wave model (SWAN), and illustrate various interacting processes using an idealized shallow basin application. The flow model has been modified to include plant posture-dependent three-dimensional drag, in-canopy wave-induced streaming, and production of turbulent kinetic energy and enstrophy to parameterize vertical mixing. The coupling framework has been updated to exchange vegetation-related variables between the flow model and the wave model to account for wave energy dissipation due to vegetation. This study i) demonstrates the validity of the plant posture-dependent drag parameterization against field measurements, ii) shows that the model is capable of reproducing the mean and turbulent flow field in the presence of vegetation as compared to various laboratory experiments, iii) provides insight into the flow-vegetation interaction through an analysis of the terms in the momentum balance, iv) describes the influence of a submerged vegetation patch on tidal currents and waves separately and combined, and v) proposes future directions for research and development.

[Models for biomass estimation of four shrub species planted in urban area of Xi'an city, Northwest China].

PubMed

Yao, Zheng-Yang; Liu, Jian-Jun

2014-01-01

Four common greening shrub species (i. e. Ligustrum quihoui, Buxus bodinieri, Berberis xinganensis and Buxus megistophylla) in Xi'an City were selected to develop the highest correlation and best-fit estimation models for the organ (branch, leaf and root) and total biomass against different independent variables. The results indicated that the organ and total biomass optimal models of the four shrubs were power functional model (CAR model) except for the leaf biomass model of B. megistophylla which was logarithmic functional model (VAR model). The independent variables included basal diameter, crown diameter, crown diameter multiplied by height, canopy area and canopy volume. B. megistophylla significantly differed from the other three shrub species in the independent variable selection, which were basal diameter and crown-related factors, respectively.

The contribution of urbanization to recent extreme heat events and a potential mitigation strategy in the Beijing-Tianjin-Hebei metropolitan area

NASA Astrophysics Data System (ADS)

Wang, Mingna; Yan, Xiaodong; Liu, Jiyuan; Zhang, Xuezhen

2013-11-01

This paper addresses the contribution of urban land use change to near-surface air temperature during the summer extreme heat events of the early twenty-first century in the Beijing-Tianjin-Hebei metropolitan area. This study uses the Weather Research Forecasting model with a single urban canopy model and the newest actual urban cover datasets. The results show that urban land use characteristics that have evolved over the past ~20 years in the Beijing-Tianjin-Hebei metropolitan area have had a significant impact on the extreme temperatures occurring during extreme heat events. Simulations show that new urban development has caused an intensification and expansion of the areas experiencing extreme heat waves with an average increase in temperature of approximately 0.60 °C. This change is most obvious at night with an increase up to 0.95 °C, for which the total contribution of anthropogenic heat is 34 %. We also simulate the effects of geo-engineering strategies increasing the albedo of urban roofs, an effective way of reducing urban heat island, which can reduce the urban mean temperature by approximately 0.51 °C and counter approximately 80 % of the heat wave results from urban sprawl during the last 20 years.

Potentialities of ensemble strategies for flood forecasting over the Milano urban area

NASA Astrophysics Data System (ADS)

Ravazzani, Giovanni; Amengual, Arnau; Ceppi, Alessandro; Homar, Víctor; Romero, Romu; Lombardi, Gabriele; Mancini, Marco

2016-08-01

Analysis of ensemble forecasting strategies, which can provide a tangible backing for flood early warning procedures and mitigation measures over the Mediterranean region, is one of the fundamental motivations of the international HyMeX programme. Here, we examine two severe hydrometeorological episodes that affected the Milano urban area and for which the complex flood protection system of the city did not completely succeed. Indeed, flood damage have exponentially increased during the last 60 years, due to industrial and urban developments. Thus, the improvement of the Milano flood control system needs a synergism between structural and non-structural approaches. First, we examine how land-use changes due to urban development have altered the hydrological response to intense rainfalls. Second, we test a flood forecasting system which comprises the Flash-flood Event-based Spatially distributed rainfall-runoff Transformation, including Water Balance (FEST-WB) and the Weather Research and Forecasting (WRF) models. Accurate forecasts of deep moist convection and extreme precipitation are difficult to be predicted due to uncertainties arising from the numeric weather prediction (NWP) physical parameterizations and high sensitivity to misrepresentation of the atmospheric state; however, two hydrological ensemble prediction systems (HEPS) have been designed to explicitly cope with uncertainties in the initial and lateral boundary conditions (IC/LBCs) and physical parameterizations of the NWP model. No substantial differences in skill have been found between both ensemble strategies when considering an enhanced diversity of IC/LBCs for the perturbed initial conditions ensemble. Furthermore, no additional benefits have been found by considering more frequent LBCs in a mixed physics ensemble, as ensemble spread seems to be reduced. These findings could help to design the most appropriate ensemble strategies before these hydrometeorological extremes, given the computational cost of running such advanced HEPSs for operational purposes.

Urban trees and forests of the Chicago region

Treesearch

David J. Nowak; Robert E. III Hoehn; Allison R. Bodine; Daniel E. Crane; John F. Dwyer; Veta Bonnewell; Gary Watson

2013-01-01

An analysis of trees in the Chicago region of Illinois reveals that this area has about 157,142,000 trees with tree and shrub canopy that covers 21.0 percent of the region. The most common tree species are European buckthorn, green ash, boxelder, black cherry, and American elm. Trees in the Chicago region currently store about 16.9 million tons of carbon (61.9 million...

Community ash densities and economic impact potential of emerald ash borer (Agrilus planipennis) in four midwestern states

Treesearch

T. Davis Sydnor; Matthew Bumgardner; Sakthi. Subburayalu

2011-01-01

A survey of 586 community representatives with urban tree canopy responsibilities was conducted to provide data on ash density within four states in the Midwestern U.S., and to examine potential economic losses should emerald ash borer (EAB) become established in their communities. One hundred twenty-three responses were received from communities of various sizes. Data...

Assessing urban forest effects and values: Douglas County, Kansas

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Alexis Ellis; Kim Bomberger; Daniel E. Crane; Theodore A. Endreny; Thomas Taggert; Emily. Stephan

2014-01-01

An analysis of trees in Douglas County, Kansas, reveals that this area has about 14,164,000 trees with tree and shrub canopy that covers 25.2 percent of the county. The most common tree species are American elm, northern hackberry, eastern redcedar, Osage-orange, and honeylocust. Trees in Douglas County currently store about 1.7 million tons of carbon (6.4 million tons...

Land fragmentationn and impacts to streams and fish in the central and upper midwest

Treesearch

Elon S. Verry

2000-01-01

Fragmentation of the land means changes in the vegetative cover. This alone has caused significant and wide spread physical and water quality changes to the streams and rivers in the central and upper Midwest. Removal of the forest canopy that changes land use to "open" conditions: agricultural, urban, or rights of way, is sufficient to initiate and prolong...

Assessing urban forest effects and values: the greater Kansas City region

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. III Hoehn; Daniel E. Crane; Alexis Ellis; Theodore A. Endreny; Yang Yang; Tom Jacobs; Kassie Shelton

2013-01-01

An analysis of trees in the greater Kansas City region of Missouri and Kansas reveals that this area has about 249,450,000 trees with tree and shrub canopy that covers 28.3 percent of the region. The most common tree species are American elm, northern hackberry, Osage-orange, honeylocust, and eastern redcedar. Trees in the greater Kansas City region currently store...

Bias Correction of MODIS AOD using DragonNET to obtain improved estimation of PM2.5

NASA Astrophysics Data System (ADS)

Gross, B.; Malakar, N. K.; Atia, A.; Moshary, F.; Ahmed, S. A.; Oo, M. M.

2014-12-01

MODIS AOD retreivals using the Dark Target algorithm is strongly affected by the underlying surface reflection properties. In particular, the operational algorithms make use of surface parameterizations trained on global datasets and therefore do not account properly for urban surface differences. This parameterization continues to show an underestimation of the surface reflection which results in a general over-biasing in AOD retrievals. Recent results using the Dragon-Network datasets as well as high resolution retrievals in the NYC area illustrate that this is even more significant at the newest C006 3 km retrievals. In the past, we used AERONET observation in the City College to obtain bias-corrected AOD, but the homogeneity assumptions using only one site for the region is clearly an issue. On the other hand, DragonNET observations provide ample opportunities to obtain better tuning the surface corrections while also providing better statistical validation. In this study we present a neural network method to obtain bias correction of the MODIS AOD using multiple factors including surface reflectivity at 2130nm, sun-view geometrical factors and land-class information. These corrected AOD's are then used together with additional WRF meteorological factors to improve estimates of PM2.5. Efforts to explore the portability to other urban areas will be discussed. In addition, annual surface ratio maps will be developed illustrating that among the land classes, the urban pixels constitute the largest deviations from the operational model.

Uncertainties in estimates of fAPAR for photosynthesis (fAPARPSN) in tropical, Arctic/boreal, coastal, and wetland-dominant regions when approximated with fAPARcanopy and NDVI

NASA Astrophysics Data System (ADS)

Zhang, Q.; Yao, T.

2016-12-01

The climate is affected by the land surface through regulating the exchange of mass and energy with the atmosphere. The energy that reaches the land surface has three pathways: (1) reflected into atmosphere; (2) absorbed for photosynthesis; and (3) discarded as latent and sensible heat or emitted as fluorescence. Vegetation removes CO2 from the atmosphere during the process of photosynthesis, but also releases CO2 back into the atmosphere through the process of respiration. The complex set of vegetation-soil-atmosphere interactions requires that a realistic land-surface parameterization be included in any climate model or general circulation model (GCM) to accurately simulate canopy photosynthesis and stomatal conductance.We retrieve fraction of PAR absorbed by chlorophyll (fAPARchl) with an advanced canopy-leaf-soil-snow-water coupled radiative transfer model. Most ecological models and land-surface models that simulate vegetation GPP with remote sensing data utilize fraction of PAR absorbed by the whole canopy (fAPARcanopy). However, only the PAR absorbed by chlorophyll is potentially available for photosynthesis since the PAR absorbed by non-photosynthetic vegetation section (NPV) of the canopy is not used for photosynthesis. Therefore, fAPARchl (rather than fAPARcanopy) should be utilized to estimate fAPAR for photosynthesis (fAPARPSN), and thus in GPP simulation. Globally selected sites include those sites in tropical, Arctic/boreal, coastal, and wetland-dominant regions. The fAPARchl and fAPARcanopy products for a surrounding area 50 km x 50 km of each site are mapped. The fAPARchl is utilized to estimate GPP, and compared to tower flux GPP for validation. The GPP estimation performance with fAPARchl is also compared with the GPP estimation performance with MOD15A2 FPAR. The fAPARchl product is further implemented into ecological models and land-surface models to simulate vegetation GPP. NDVI is the other proxy of fAPARPSN in GPP estimation. We quantify the uncertainties in estimates of fAPARPSN when approximated with fAPARcanopy and NDVI. The uncertainties are significant and vary spatially, temporally, and with plant functional types.

Variability in snowpack accumulation and ablation associated with mountain pine beetle infestation in western forests

NASA Astrophysics Data System (ADS)

Biederman, J. A.; Harpold, A. A.; Gochis, D. J.; Reed, D.; Brooks, P. D.

2010-12-01

Seasonal snowcover is a primary source of water to urban and agricultural regions in the western United States, where Mountain Pine Beetle (MPB) has caused rapid and extensive changes to vegetation in montane forests. Levels of MPB infestation in these seasonally snow-covered systems are unprecedented, and it is unknown how this will affect water yield, especially in changing climate conditions. To address this unknown we ask: How does snow accumulation and ablation vary across forest with differing levels of impact? Our study areas in the Rocky Mountains of CO and WY are similar in latitude, elevation and forest structure before infestation, but they vary in the intensity and timing of beetle infestation and tree mortality. We present a record for winter 2010 that includes continuous snow depth as well as stand-scale snow surveys at maximum accumulation. Additional measurements include snowfall, net radiation, temperature and wind speed as well as characterization of forest structure by leaf area index. In a stand uninfested by MPB, maximum snow depth was fairly uniform under canopy (mean = 86 cm, coefficient of variation = 0.021), while canopy gaps showed greater and more variable depth (mean = 117 cm, CV = 0.111). This is consistent with several studies demonstrating that snowfall into canopy gaps depends upon gap size, orientation, wind speed and storm size. In a stand impacted in 2007, snow depth under canopy was less uniform, and there were smaller differences in both mean depth and variability between canopy (mean = 93 cm, CV = 0.072) and gaps (mean = 97 cm, CV = 0.070), consistent with decreased canopy density. In a more recently infested (2009) stand with an intermediate level of MPB impact, mean snow depths were similar between canopy (96 cm, CV = 0.016) and gaps (95 cm, CV = 0.185) but gaps showed much greater variability, suggesting controls similar to those in effect in the uninfested stand. We further use these data to model snow accumulation and ablation as a function of vegetation, topography and fine-scale climate variability, with preliminary results presented at the meeting.

Analysis of energy fluxes and vegetation-atmosphere parameters in irrigated and natural ecosystems of semi-arid Brazil

NASA Astrophysics Data System (ADS)

Teixeira, A. H. de Castro; Bastiaanssen, W. G. M.; Ahmad, M. D.; Moura, M. S. B.; Bos, M. G.

2008-11-01

SummaryKnowledge on evapotranspiration is essential in quantifying water use depletion and to allocate scarce water resources to competing uses. Despite that an extensive literature describes the theoretical mechanisms of turbulent water vapour transport above and within crop canopies fewer studies have examined land surface parameters within composite landscapes of irrigated crops and semi-arid natural vegetation. Aiming to improve parameterizations of the radiation and energy balance in irrigated crops and natural vegetation, micro-climatic measurements were carried out on irrigated land (vineyards and mango orchard) and natural vegetation (caatinga) in the semi-arid zone of the São Francisco River basin (Brazil) from 2002 to 2005. The fractions of 24 h incident solar radiation available for net radiation were 46%, 55%, 51% and 53%, for wine grape, table grape, mango orchard and caatinga, respectively. Daily evaporative fractions of the net available energy used as latent heat flux ( λE) were 0.80, 0.88, 0.75 and 0.33 respectively. The daylight values of bulk surface resistances ( rs) averaged 128 s m -1, 73 s m -1, 133 s m -1 and 1940 s m -1 for wine grape, table grape, mango orchard and caatinga, respectively. Simplified parameterizations on roughness and evaporation resistances were performed. It could be concluded that net radiation can be estimated by means of a linear expression with incident global solar radiation depending on the type of vegetation. The variability of aerodynamic resistance ( ra) could be mainly explained by the friction velocity ( u ∗) which on turn depends on the surface roughness length for momentum transport ( z 0m). The experimental data showed that for sparse canopies z 0m being 9% of the mean vegetation height is a doable operational rule for the semi-arid region of São Francisco River basin. The seasonal values of rs for irrigated crops were highly correlated with water vapour pressure deficit. The availability of analytical methods to assess ra and rs makes the one-step Penman-Monteith equation suitable for the computation of actual evapotranspiration and water productivity analyses.

Estimation of vegetation photosynthetic capacity from space-based measurements of chlorophyll fluorescence for terrestrial biosphere models.

PubMed

Zhang, Yongguang; Guanter, Luis; Berry, Joseph A; Joiner, Joanna; van der Tol, Christiaan; Huete, Alfredo; Gitelson, Anatoly; Voigt, Maximilian; Köhler, Philipp

2014-12-01

Photosynthesis simulations by terrestrial biosphere models are usually based on the Farquhar's model, in which the maximum rate of carboxylation (Vcmax ) is a key control parameter of photosynthetic capacity. Even though Vcmax is known to vary substantially in space and time in response to environmental controls, it is typically parameterized in models with tabulated values associated to plant functional types. Remote sensing can be used to produce a spatially continuous and temporally resolved view on photosynthetic efficiency, but traditional vegetation observations based on spectral reflectance lack a direct link to plant photochemical processes. Alternatively, recent space-borne measurements of sun-induced chlorophyll fluorescence (SIF) can offer an observational constraint on photosynthesis simulations. Here, we show that top-of-canopy SIF measurements from space are sensitive to Vcmax at the ecosystem level, and present an approach to invert Vcmax from SIF data. We use the Soil-Canopy Observation of Photosynthesis and Energy (SCOPE) balance model to derive empirical relationships between seasonal Vcmax and SIF which are used to solve the inverse problem. We evaluate our Vcmax estimation method at six agricultural flux tower sites in the midwestern US using spaced-based SIF retrievals. Our Vcmax estimates agree well with literature values for corn and soybean plants (average values of 37 and 101 μmol m(-2)  s(-1) , respectively) and show plausible seasonal patterns. The effect of the updated seasonally varying Vcmax parameterization on simulated gross primary productivity (GPP) is tested by comparing to simulations with fixed Vcmax values. Validation against flux tower observations demonstrate that simulations of GPP and light use efficiency improve significantly when our time-resolved Vcmax estimates from SIF are used, with R(2) for GPP comparisons increasing from 0.85 to 0.93, and for light use efficiency from 0.44 to 0.83. Our results support the use of space-based SIF data as a proxy for photosynthetic capacity and suggest the potential for global, time-resolved estimates of Vcmax . © 2014 John Wiley & Sons Ltd.

Can green roofs reduce urban heat stress in vulnerable urban communities: A coupled atmospheric and social modeling approach

NASA Astrophysics Data System (ADS)

Sharma, A.; Woodruff, S.; Budhathoki, M.; Hamlet, A. F.; Fernando, H. J. S.; Chen, F.

2017-12-01

Urban areas provide organized, engineered, sociological and economical infrastructure designed to provide a high quality of life, but the implementation and management of urban infrastructure has been a continued challenge. Increasing urbanization, warming climate, as well as anthropogenic heat emissions that accompany urban development generates "stress". This rapidly increasing `urban stress' affects the sustainability of cities, making populations more vulnerable to extreme hazards, such as heat. Cities are beginning to extensively use green roofs as a potential urban heat mitigation strategy. This study explores the potential of green roofs to reduce summertime temperatures in the most vulnerable neighborhoods of the Chicago metropolitan area by combining social vulnerability indices (a function of exposure, sensitivity and adaptive capacity), and temperatures from mesoscale model. Numerical simulations using urbanized version the Advanced Research Weather Research and Forecasting (WRF) model were performed to measure rooftop temperatures, a representative variable for exposure in this study. The WRF simulations were dynamically coupled with a green roof algorithm as a part of urban parameterization within WRF. Specifically, the study examines roof surface temperature with changing green roof fractions and how would they help reduce exposure to heat stress for vulnerable urban communities. This study shows an example of applied research that can directly benefit urban communities and be used by urban planners to evaluate mitigation strategies.

Could urban greening mitigate suburban thermal inequity?: the role of residents’ dispositions and household practices

NASA Astrophysics Data System (ADS)

Byrne, Jason; Ambrey, Christopher; Portanger, Chloe; Lo, Alex; Matthews, Tony; Baker, Douglas; Davison, Aidan

2016-09-01

Over the past decade research on urban thermal inequity has grown, with a focus on denser built environments. In this letter we examine thermal inequity associated with climate change impacts and changes to urban form in a comparatively socio-economically disadvantaged Australian suburb. Local urban densification policies designed to counteract sprawl have reduced block sizes, increased height limits, and diminished urban tree canopy cover (UTC). Little attention has been given to the combined effects of lower UTC and increased heat on disadvantaged residents. Such impacts include rising energy expenditure to maintain thermal comfort (i.e. cooling dwellings). We used a survey of residents (n = 230) to determine their perceptions of climate change impacts; household energy costs; household thermal comfort practices; and dispositions towards using green infrastructure to combat heat. Results suggest that while comparatively disadvantaged residents spend more on energy as a proportion of their income, they appear to have reduced capacity to adapt to climate change at the household scale. We found most residents favoured more urban greening and supported tree planting in local parks and streets. Findings have implications for policy responses aimed at achieving urban climate justice.

The influence of roadside solid and vegetation barriers on near-road air quality

NASA Astrophysics Data System (ADS)

Ghasemian, Masoud; Amini, Seyedmorteza; Princevac, Marko

2017-12-01

The current study evaluates the influence of roadside solid and vegetation barriers on the near-road air quality. Reynolds Averaged Navier-Stokes (RANS) technique coupled with the k - ε realizable turbulence model is utilized to investigate the flow pattern and pollutant concentration. A scalar transport equation is solved for a tracer gas to represent the roadway pollutant emissions. In addition, a broad range of turbulent Schmidt numbers are tested to calibrate the scalar transport equation. Three main scenarios including flat terrain, solid barrier, and vegetative barrier are studied. To validate numerical methodology, predicted pollutant concentration is compared with published wind tunnel data. Results show that the solid barrier induces an updraft motion and lofts the vehicle emission plume. Therefore, the ground-level pollutant concentration decreases compared to the flat terrain. For the vegetation barrier, different sub-scenarios with different vegetation densities ranging from approximately flat terrain to nearly solid barrier are examined. Dense canopies act in a similar manner as a solid barrier and mitigate the pollutant concentration through vertical mixing. On the other hand, the high porosity vegetation barriers reduce the wind speed and lead to a higher pollutant concentration. As the vegetation density increases, i.e. the barrier porosity decreases, the recirculation zone behind the canopy becomes larger and moves toward the canopy. The dense plant canopy with LAD = 3.33m-2m3 can improve the near-road air quality by 10% and high porosity canopy with LAD = 1m-2m3 deteriorates near-road air quality by 15%. The results of this study can be implemented as green infrastructure design strategies by urban planners and forestry organizations.

Large-Eddy Simulation of Coherent Flow Structures within a Cubical Canopy

NASA Astrophysics Data System (ADS)

Inagaki, Atsushi; Castillo, Marieta Cristina L.; Yamashita, Yoshimi; Kanda, Manabu; Takimoto, Hiroshi

2012-02-01

Instantaneous flow structures "within" a cubical canopy are investigated via large-eddy simulation. The main topics of interest are, (1) large-scale coherent flow structures within a cubical canopy, (2) how the structures are coupled with the turbulent organized structures (TOS) above them, and (3) the classification and quantification of representative instantaneous flow patterns within a street canyon in relation to the coherent structures. We use a large numerical domain (2,560 m × 2,560 m × 1,710 m) with a fine spatial resolution (2.5 m), thereby simulating a complete daytime atmospheric boundary layer (ABL), as well as explicitly resolving a regular array of cubes (40 m in height) at the surface. A typical urban ABL is numerically modelled. In this situation, the constant heat supply from roof and floor surfaces sustains a convective mixed layer as a whole, but strong wind shear near the canopy top maintains the surface layer nearly neutral. The results reveal large coherent structures in both the velocity and temperature fields "within" the canopy layer. These structures are much larger than the cubes, and their shapes and locations are shown to be closely related to the TOS above them. We classify the instantaneous flow patterns in a cavity, specifically focusing on two characteristic flow patterns: flushing and cavity-eddy events. Flushing indicates a strong upward motion, while a cavity eddy is characterized by a dominant vortical motion within a single cavity. Flushing is clearly correlated with the TOS above, occurring frequently beneath low-momentum streaks. The instantaneous momentum and heat transport within and above a cavity due to flushing and cavity-eddy events are also quantified.

ORCHILEAK (revision 3875): a new model branch to simulate carbon transfers along the terrestrial-aquatic continuum of the Amazon basin

NASA Astrophysics Data System (ADS)

Lauerwald, Ronny; Regnier, Pierre; Camino-Serrano, Marta; Guenet, Bertrand; Guimberteau, Matthieu; Ducharne, Agnès; Polcher, Jan; Ciais, Philippe

2017-10-01

Lateral transfer of carbon (C) from terrestrial ecosystems into the inland water network is an important component of the global C cycle, which sustains a large aquatic CO2 evasion flux fuelled by the decomposition of allochthonous C inputs. Globally, estimates of the total C exports through the terrestrial-aquatic interface range from 1.5 to 2.7 Pg C yr-1 (Cole et al., 2007; Battin et al., 2009; Tranvik et al., 2009), i.e. of the order of 2-5 % of the terrestrial NPP. Earth system models (ESMs) of the climate system ignore these lateral transfers of C, and thus likely overestimate the terrestrial C sink. In this study, we present the implementation of fluvial transport of dissolved organic carbon (DOC) and CO2 into ORCHIDEE (Organising Carbon and Hydrology in Dynamic Ecosystems), the land surface scheme of the Institut Pierre-Simon Laplace ESM. This new model branch, called ORCHILEAK, represents DOC production from canopy and soils, DOC and CO2 leaching from soils to streams, DOC decomposition, and CO2 evasion to the atmosphere during its lateral transport in rivers, as well as exchange with the soil carbon and litter stocks on floodplains and in swamps. We parameterized and validated ORCHILEAK for the Amazon basin, the world's largest river system with regard to discharge and one of the most productive ecosystems in the world. With ORCHILEAK, we are able to reproduce observed terrestrial and aquatic fluxes of DOC and CO2 in the Amazon basin, both in terms of mean values and seasonality. In addition, we are able to resolve the spatio-temporal variability in C fluxes along the canopy-soil-water continuum at high resolution (1°, daily) and to quantify the different terrestrial contributions to the aquatic C fluxes. We simulate that more than two-thirds of the Amazon's fluvial DOC export are contributed by the decomposition of submerged litter. Throughfall DOC fluxes from canopy to ground are about as high as the total DOC inputs to inland waters. The latter, however, are mainly sustained by litter decomposition. Decomposition of DOC and submerged plant litter contributes slightly more than half of the CO2 evasion from the water surface, while the remainder is contributed by soil respiration. Total CO2 evasion from the water surface equals about 5 % of the terrestrial NPP. Our results highlight that ORCHILEAK is well suited to simulate carbon transfers along the terrestrial-aquatic continuum of tropical forests. It also opens the perspective that provided parameterization, calibration and validation is performed for other biomes, the new model branch could improve the quantification of the global terrestrial C sink and help better constrain carbon cycle-climate feedbacks in future projections.

Nested High Resolution Modeling of the Impact of Urbanization on Regional Climate in Three Vast Urban Agglomerations in China

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei; Hu, Yonghong; Jia, Gensuo

2013-04-01

In this paper, the Weather Research and Forecasting (WRF) model coupled to the Urban Canopy Model (UCM) is employed to simulate the impact of urbanization on the regional climate over three vast city agglomerations in China. Based on high resolution land use and land cover data, two scenarios are designed to represent the non-urban and current urban land use distributions. By comparing the results of two nested, high resolution numerical experiments, the spatial and temporal changes on surface air temperature, heat stress index, surface energy budget and precipitation due to urbanization are analyzed and quantified. Urban expansion increases the surface air temperature in urban areas by about 1? and this climatic forcing of urbanization on temperature is more pronounced in summer and nighttime than other seasons and daytime. The heat stress intensity, which reflects the combined effects of temperature and humidity, is enhanced by about 0.5 units in urban areas. The regional incoming solar radiation increases after urban expansion, which may be caused by the reduction of cloud fraction. The increased temperature and roughness of the urban surface lead to enhanced convergence. Meanwhile, the planetary boundary layer is deepened and water vapor is mixed more evenly in the lower atmosphere. The deficit of water vapor leads to less convective available potential energy and more convective inhibition energy. Finally, these combined effects may reduce the rainfall amount over urban area mainly in summer and change the regional precipitation pattern to a certain extent.

Modeling Global Urbanization Supported by Nighttime Light Remote Sensing

NASA Astrophysics Data System (ADS)

Zhou, Y.

2015-12-01

Urbanization, a major driver of global change, profoundly impacts our physical and social world, for example, altering carbon cycling and climate. Understanding these consequences for better scientific insights and effective decision-making unarguably requires accurate information on urban extent and its spatial distributions. In this study, we developed a cluster-based method to estimate the optimal thresholds and map urban extents from the nighttime light remote sensing data, extended this method to the global domain by developing a computational method (parameterization) to estimate the key parameters in the cluster-based method, and built a consistent 20-year global urban map series to evaluate the time-reactive nature of global urbanization (e.g. 2000 in Fig. 1). Supported by urban maps derived from nightlights remote sensing data and socio-economic drivers, we developed an integrated modeling framework to project future urban expansion by integrating a top-down macro-scale statistical model with a bottom-up urban growth model. With the models calibrated and validated using historical data, we explored urban growth at the grid level (1-km) over the next two decades under a number of socio-economic scenarios. The derived spatiotemporal information of historical and potential future urbanization will be of great value with practical implications for developing adaptation and risk management measures for urban infrastructure, transportation, energy, and water systems when considered together with other factors such as climate variability and change, and high impact weather events.

Study of different deposition parameterizations on an atmospheric mesoscale Eulerian air quality model: Madrid case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

San Jose, R.; Cortes, J.; Moreno, J.

1996-12-31

The importance of an adequate parameterization of the deposition process for the simulation of the three dimensional pollution fields in a mesoscale context is out of any doubt. An accurate parameterization of the deposition flux is essential for a precise determination of the flux removal and for allowing longer simulation periods of the atmospheric processes. In addition, an accurate deposition pattern will allow a much more precise diagnostic of the impact of different pollutants on the different types of terrain actually present in complex environments such as the urban ones and their environs. In this contribution, we have implemented amore » complex resistance deposition model into an Air Quality System (ANA) applied over a large city such as Madrid (Spain). The model domain is 80x100 km which is much larger than the actual urban domain. The ANA model is composed on four different modules; a meteorological module which solves numerically the Navier Stokes equations and predicts the wind, temperature and humidity three dimensional fields every time step; the emission module, which produces the emissions every hour and with a high spatial resolution (250 x 250 m) and with landuse information (for biogenic emissions) from the Landsat-5 satellite image; a photochemical modules, which is based on the CBM-IV mechanism and solved numerically by following the SMVGEAR method and finally, a deposition module which is based on the resistance approach. The resistance module takes into account the landuse classification, the global solar radiation, the humidity of the terrain, the pH of the terrain, the characteristics of the pollutant, the Leaf Area Index and the reactivity of the pollutant.« less

An ecology of prestige in New York City: Examining the relationships among population density, socio-economic status, group identity, and residential canopy cover

Treesearch

J. Morgan Grove; Dexter H. Locke; Jarlath P.M. O' Neil-Dunne

2014-01-01

Several social theories have been proposed to explain the uneven distribution of vegetation in urban residential areas: population density, social stratification, luxury effect, and ecology of prestige. We evaluate these theories using a combination of demographic and socio-economic predictors of vegetative cover on all residential lands in New York City. We use...

Thermal Remote Sensing with Uav-Based Workflows

NASA Astrophysics Data System (ADS)

Boesch, R.

2017-08-01

Climate change will have a significant influence on vegetation health and growth. Predictions of higher mean summer temperatures and prolonged summer draughts may pose a threat to agriculture areas and forest canopies. Rising canopy temperatures can be an indicator of plant stress because of the closure of stomata and a decrease in the transpiration rate. Thermal cameras are available for decades, but still often used for single image analysis, only in oblique view manner or with visual evaluations of video sequences. Therefore remote sensing using a thermal camera can be an important data source to understand transpiration processes. Photogrammetric workflows allow to process thermal images similar to RGB data. But low spatial resolution of thermal cameras, significant optical distortion and typically low contrast require an adapted workflow. Temperature distribution in forest canopies is typically completely unknown and less distinct than for urban or industrial areas, where metal constructions and surfaces yield high contrast and sharp edge information. The aim of this paper is to investigate the influence of interior camera orientation, tie point matching and ground control points on the resulting accuracy of bundle adjustment and dense cloud generation with a typically used photogrammetric workflow for UAVbased thermal imagery in natural environments.

Modelling temporal variance of component temperatures and directional anisotropy over vegetated canopy

NASA Astrophysics Data System (ADS)

Bian, Zunjian; du, yongming; li, hua

2016-04-01

Land surface temperature (LST) as a key variable plays an important role on hydrological, meteorology and climatological study. Thermal infrared directional anisotropy is one of essential factors to LST retrieval and application on longwave radiance estimation. Many approaches have been proposed to estimate directional brightness temperatures (DBT) over natural and urban surfaces. While less efforts focus on 3-D scene and the surface component temperatures used in DBT models are quiet difficult to acquire. Therefor a combined 3-D model of TRGM (Thermal-region Radiosity-Graphics combined Model) and energy balance method is proposed in the paper for the attempt of synchronously simulation of component temperatures and DBT in the row planted canopy. The surface thermodynamic equilibrium can be final determined by the iteration strategy of TRGM and energy balance method. The combined model was validated by the top-of-canopy DBTs using airborne observations. The results indicated that the proposed model performs well on the simulation of directional anisotropy, especially the hotspot effect. Though we find that the model overestimate the DBT with Bias of 1.2K, it can be an option as a data reference to study temporal variance of component temperatures and DBTs when field measurement is inaccessible

Process analysis of characteristics of the boundary layer during a heavy haze pollution episode in an inland megacity, China.

PubMed

Wang, Shan; Liao, Tingting; Wang, Lili; Sun, Yang

2016-02-01

Ground observation data from 8 meteorological stations in Xi'an, air mass concentration data from 13 environmental quality monitoring sites in Xi'an, as well as radiosonde observation and wind profile radar data, were used in this study. Thereby, the process, causes and boundary layer meteorological characteristics of a heavy haze episode occurring from 16 to 25 December 2013 in Xi'an were analyzed. Principal component analysis showed that this haze pollution was mainly caused by the high-intensity emission and formation of gaseous pollutants (NO2, CO and SO2) and atmospheric particles (PM2.5 (fine particles) and PM10 (respirable suspended particle). The second cause was the relative humidity and continuous low temperature. The third cause was the allocation of the surface pressure field. The presence of a near-surface temperature inversion at the boundary layer formed favorable stratification conditions for the formation and maintenance of heavy haze pollution. The persistent thick haze layer weakened the solar radiation. Meanwhile, a warming effect in the urban canopy layer and in the transition zone from the urban friction sublayer to the urban canopy was indicated. All these conditions facilitated the maintenance and reinforcement of temperature inversion. The stable atmospheric stratification finally acted on the wind field in the boundary layer, and further weakened the exchange capacity of vertical turbulence. The superposition of a wind field with the horizontal gentle wind induced the typical air stagnation and finally caused the deterioration of air quality during this haze event. Copyright © 2015. Published by Elsevier B.V.

Real-Time Characterization of Aerosol Particle Composition above the Urban Canopy in Beijing: Insights into the Interactions between the Atmospheric Boundary Layer and Aerosol Chemistry.

PubMed

Sun, Yele; Du, Wei; Wang, Qingqing; Zhang, Qi; Chen, Chen; Chen, Yong; Chen, Zhenyi; Fu, Pingqing; Wang, Zifa; Gao, Zhiqiu; Worsnop, Douglas R

2015-10-06

Despite extensive efforts into the characterization of air pollution during the past decade, real-time characterization of aerosol particle composition above the urban canopy in the megacity Beijing has never been performed to date. Here we conducted the first simultaneous real-time measurements of aerosol composition at two different heights at the same location in urban Beijing from December 19, 2013 to January 2, 2014. The nonrefractory submicron aerosol (NR-PM1) species were measured in situ by a high-resolution aerosol mass spectrometer at near-ground level and an aerosol chemical speciation monitor at 260 m on a 325 m meteorological tower in Beijing. Secondary aerosol showed similar temporal variations between ground level and 260 m, whereas much weaker correlations were found for the primary aerosol. The diurnal evolution of the ratios and correlations of aerosol species between 260 m and the ground level further illustrated a complex interaction between vertical mixing processes and local source emissions on aerosol chemistry in the atmospheric boundary layer. As a result, the aerosol compositions at the two heights were substantially different. Organic aerosol (OA), mainly composed of primary OA (62%), at the ground level showed a higher contribution to NR-PM1 (65%) than at 260 m (54%), whereas a higher concentration and contribution (15%) of nitrate was observed at 260 m, probably due to the favorable gas-particle partitioning under lower temperature conditions. In addition, two different boundary layer structures were observed, each interacting differently with the evolution processes of aerosol chemistry.

Visualization of simulated urban spaces: inferring parameterized generation of streets, parcels, and aerial imagery.

PubMed

Vanegas, Carlos A; Aliaga, Daniel G; Benes, Bedrich; Waddell, Paul

2009-01-01

Urban simulation models and their visualization are used to help regional planning agencies evaluate alternative transportation investments, land use regulations, and environmental protection policies. Typical urban simulations provide spatially distributed data about number of inhabitants, land prices, traffic, and other variables. In this article, we build on a synergy of urban simulation, urban visualization, and computer graphics to automatically infer an urban layout for any time step of the simulation sequence. In addition to standard visualization tools, our method gathers data of the original street network, parcels, and aerial imagery and uses the available simulation results to infer changes to the original urban layout and produce a new and plausible layout for the simulation results. In contrast with previous work, our approach automatically updates the layout based on changes in the simulation data and thus can scale to a large simulation over many years. The method in this article offers a substantial step forward in building integrated visualization and behavioral simulation systems for use in community visioning, planning, and policy analysis. We demonstrate our method on several real cases using a 200 GB database for a 16,300 km2 area surrounding Seattle.

A roadmap for improving the representation of photosynthesis in Earth system models.

PubMed

Rogers, Alistair; Medlyn, Belinda E; Dukes, Jeffrey S; Bonan, Gordon; von Caemmerer, Susanne; Dietze, Michael C; Kattge, Jens; Leakey, Andrew D B; Mercado, Lina M; Niinemets, Ülo; Prentice, I Colin; Serbin, Shawn P; Sitch, Stephen; Way, Danielle A; Zaehle, Sönke

2017-01-01

Accurate representation of photosynthesis in terrestrial biosphere models (TBMs) is essential for robust projections of global change. However, current representations vary markedly between TBMs, contributing uncertainty to projections of global carbon fluxes. Here we compared the representation of photosynthesis in seven TBMs by examining leaf and canopy level responses of photosynthetic CO 2 assimilation (A) to key environmental variables: light, temperature, CO 2 concentration, vapor pressure deficit and soil water content. We identified research areas where limited process knowledge prevents inclusion of physiological phenomena in current TBMs and research areas where data are urgently needed for model parameterization or evaluation. We provide a roadmap for new science needed to improve the representation of photosynthesis in the next generation of terrestrial biosphere and Earth system models. No claim to original US Government works New Phytologist © 2016 New Phytologist Trust.

Nested high-resolution modeling of the impact of urbanization on regional climate in three vast urban agglomerations in China

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei; Hu, Yonghong; Jia, Gensuo

2012-11-01

In this paper, the Weather Research and Forecasting Model, coupled to the Urban Canopy Model, is employed to simulate the impact of urbanization on the regional climate over three vast city agglomerations in China. Based on high-resolution land use and land cover data, two scenarios are designed to represent the nonurban and current urban land use distributions. By comparing the results of two nested, high-resolution numerical experiments, the spatial and temporal changes on surface air temperature, heat stress index, surface energy budget, and precipitation due to urbanization are analyzed and quantified. Urban expansion increases the surface air temperature in urban areas by about 1°C, and this climatic forcing of urbanization on temperature is more pronounced in summer and nighttime than other seasons and daytime. The heat stress intensity, which reflects the combined effects of temperature and humidity, is enhanced by about 0.5 units in urban areas. The regional incoming solar radiation increases after urban expansion, which may be caused by the reduction of cloud fraction. The increased temperature and roughness of the urban surface lead to enhanced convergence. Meanwhile, the planetary boundary layer is deepened, and water vapor is mixed more evenly in the lower atmosphere. The deficit of water vapor leads to less convective available potential energy and more convective inhibition energy. Finally, these combined effects may reduce the rainfall amount over urban areas, mainly in summer, and change the regional precipitation pattern to a certain extent.

Impact of Extensive Urbanization on Summertime Rainfall in the Beijing Region and the Role of Local Precipitation Recycling

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei

2018-04-01

In this study, we conducted nested high-resolution simulations using the Weather Research and Forecasting model coupled with a single-layer urban canopy model to investigate the impact of extensive urbanization on regional precipitation over the Beijing-Tianjin-Hebei region in China. The results showed that extensive urbanization decreased precipitation considerably over and downwind of Beijing city. The prevalence of impermeable urban land inhibits local evaporation that feeds moisture into the overlying atmosphere, decreasing relative humidity and atmospheric instability. The dynamic precipitation recycling model was employed to estimate the precipitation that originates from local surface evaporation and large-scale advection of moisture. Results showed that about 11% of the urbanization-induced decrease in total precipitation over the Greater Beijing Region and its surroundings was contributed by the decrease in local recycled precipitation, while the other part (89%) was due to decreasing large-scale advected precipitation. Results suggest that the low evaporation from urban land surfaces not only reduces the supply of water vapor for local recycled precipitation directly but also decreases the convective available potential energy and hence the conversion efficiency of atmospheric moisture into rainfall. The urbanization-induced variations in local recycled precipitation were found to be correlated with the net atmospheric moisture flux on a monthly time scale.

Unstructured meshing and parameter estimation for urban dam-break flood modeling: building treatments and implications for accuracy and efficiency

NASA Astrophysics Data System (ADS)

Schubert, J. E.; Sanders, B. F.

2011-12-01

Urban landscapes are at the forefront of current research efforts in the field of flood inundation modeling for two major reasons. First, urban areas hold relatively large economic and social importance and as such it is imperative to avoid or minimize future damages. Secondly, urban flooding is becoming more frequent as a consequence of continued development of impervious surfaces, population growth in cities, climate change magnifying rainfall intensity, sea level rise threatening coastal communities, and decaying flood defense infrastructure. In reality urban landscapes are particularly challenging to model because they include a multitude of geometrically complex features. Advances in remote sensing technologies and geographical information systems (GIS) have promulgated fine resolution data layers that offer a site characterization suitable for urban inundation modeling including a description of preferential flow paths, drainage networks and surface dependent resistances to overland flow. Recent research has focused on two-dimensional modeling of overland flow including within-curb flows and over-curb flows across developed parcels. Studies have focused on mesh design and parameterization, and sub-grid models that promise improved performance relative to accuracy and/or computational efficiency. This presentation addresses how fine-resolution data, available in Los Angeles County, are used to parameterize, initialize and execute flood inundation models for the 1963 Baldwin Hills dam break. Several commonly used model parameterization strategies including building-resistance, building-block and building hole are compared with a novel sub-grid strategy based on building-porosity. Performance of the models is assessed based on the accuracy of depth and velocity predictions, execution time, and the time and expertise required for model set-up. The objective of this study is to assess field-scale applicability, and to obtain a better understanding of advantages and drawbacks of each method, and to recommend best practices for future studies. The Baldwin Hills dam-break flood is interesting for a couple of reasons. First, the flood caused high velocity, rapidly varied flow through a residential neighborhood and extensive damage to dozens residential structures. These conditions pose a challenge for many numerical models, the test is a rigorous one. Second, previous research has shown that flood extent predictions are sensitive to topographic data and stream flow predictions are sensitive to resistance parameters. Given that the representation of buildings affects the modeling of topography and resistance, a sensitivity to the representation of buildings is expected. Lastly, the site is supported by excellent geospatial data including validation datasets, and is made available through the Los Angeles County Imagery Acquisition Consortium (LAR-IAC), a joint effort of many public agencies in Los Angeles County to provide county-wide data. Hence, a broader aim of this study is to characterize the most useful aspects of the LAR-IAC data from a flood mapping perspective.

New York City Impact on Regional Heat Wave

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz, Luis E.; Schoonen, Martin

Abstract Extreme heat events are projected to increase in magnitude and frequency throughout this century due to increasing global temperatures, making it critically important to acquire improved understanding of their genesis and interactions with large cities. This study presents an application of the factor separation method to assess combined impacts of a synoptic scale heat wave, urban land cover, and urban energy and momentum fluxes on temperatures and winds over New York City via use of high resolution simulations (1 km grid spacing) with an urbanized WRF model. Results showed that, while the heat wave had the largest contribution tomore » temperatures (> 8°C), urban surface factors matched it in highly urbanized areas. Surface factors matched this in highly urbanized areas during night and early morning hours, with contributions up to 5°C, when calm land breeze conditions result in a strong urban heat island. Positive interactions between all factors during morning and nighttime indicate urban heat island amplification of up to 4°C during the heat wave. Midtown Manhattan vertical cross-sections, where urban canopies are most dense, showed a change in the sign (from positive to negative) of the contribution of the urban fluxes between night and day below 500 m, possibly due to radiation blocking and increased thermal storage by buildings as well as frictional effects opposing the incoming warm air.« less

New York City Impact on Regional Heat Wave

DOE PAGES

Ortiz, Luis E.; Schoonen, Martin

2018-04-01

Abstract Extreme heat events are projected to increase in magnitude and frequency throughout this century due to increasing global temperatures, making it critically important to acquire improved understanding of their genesis and interactions with large cities. This study presents an application of the factor separation method to assess combined impacts of a synoptic scale heat wave, urban land cover, and urban energy and momentum fluxes on temperatures and winds over New York City via use of high resolution simulations (1 km grid spacing) with an urbanized WRF model. Results showed that, while the heat wave had the largest contribution tomore » temperatures (> 8°C), urban surface factors matched it in highly urbanized areas. Surface factors matched this in highly urbanized areas during night and early morning hours, with contributions up to 5°C, when calm land breeze conditions result in a strong urban heat island. Positive interactions between all factors during morning and nighttime indicate urban heat island amplification of up to 4°C during the heat wave. Midtown Manhattan vertical cross-sections, where urban canopies are most dense, showed a change in the sign (from positive to negative) of the contribution of the urban fluxes between night and day below 500 m, possibly due to radiation blocking and increased thermal storage by buildings as well as frictional effects opposing the incoming warm air.« less

Impacts of Light Use Efficiency and fPAR Parameterization on Gross Primary Production Modeling

NASA Technical Reports Server (NTRS)

Cheng, Yen-Ben; Zhang, Qingyuan; Lyapustin, Alexei I.; Wang, Yujie; Middleton, Elizabeth M.

2014-01-01

This study examines the impact of parameterization of two variables, light use efficiency (LUE) and the fraction of absorbed photosynthetically active radiation (fPAR or fAPAR), on gross primary production(GPP) modeling. Carbon sequestration by terrestrial plants is a key factor to a comprehensive under-standing of the carbon budget at global scale. In this context, accurate measurements and estimates of GPP will allow us to achieve improved carbon monitoring and to quantitatively assess impacts from cli-mate changes and human activities. Spaceborne remote sensing observations can provide a variety of land surface parameterizations for modeling photosynthetic activities at various spatial and temporal scales. This study utilizes a simple GPP model based on LUE concept and different land surface parameterizations to evaluate the model and monitor GPP. Two maize-soybean rotation fields in Nebraska, USA and the Bartlett Experimental Forest in New Hampshire, USA were selected for study. Tower-based eddy-covariance carbon exchange and PAR measurements were collected from the FLUXNET Synthesis Dataset. For the model parameterization, we utilized different values of LUE and the fPAR derived from various algorithms. We adapted the approach and parameters from the MODIS MOD17 Biome Properties Look-Up Table (BPLUT) to derive LUE. We also used a site-specific analytic approach with tower-based Net Ecosystem Exchange (NEE) and PAR to estimate maximum potential LUE (LUEmax) to derive LUE. For the fPAR parameter, the MODIS MOD15A2 fPAR product was used. We also utilized fAPAR chl, a parameter accounting for the fAPAR linked to the chlorophyll-containing canopy fraction. fAPAR chl was obtained by inversion of a radiative transfer model, which used the MODIS-based reflectances in bands 1-7 produced by Multi-Angle Implementation of Atmospheric Correction (MAIAC) algorithm. fAPAR chl exhibited seasonal dynamics more similar with the flux tower based GPP than MOD15A2 fPAR, especially in the spring and fall at the agricultural sites. When using the MODIS MOD17-based parameters to estimate LUE, fAPAR chl generated better agreements with GPP (r2= 0.79-0.91) than MOD15A2 fPAR (r2= 0.57-0.84).However, underestimations of GPP were also observed, especially for the crop fields. When applying the site-specific LUE max value to estimate in situ LUE, the magnitude of estimated GPP was closer to in situ GPP; this method produced a slight overestimation for the MOD15A2 fPAR at the Bartlett forest. This study highlights the importance of accurate land surface parameterizations to achieve reliable carbon monitoring capabilities from remote sensing information.

A photosynthesis-based two-leaf canopy stomatal ...

EPA Pesticide Factsheets

A coupled photosynthesis-stomatal conductance model with single-layer sunlit and shaded leaf canopy scaling is implemented and evaluated in a diagnostic box model with the Pleim-Xiu land surface model (PX LSM) and ozone deposition model components taken directly from the meteorology and air quality modeling system—WRF/CMAQ (Weather Research and Forecast model and Community Multiscale Air Quality model). The photosynthesis-based model for PX LSM (PX PSN) is evaluated at a FLUXNET site for implementation against different parameterizations and the current PX LSM approach with a simple Jarvis function (PX Jarvis). Latent heat flux (LH) from PX PSN is further evaluated at five FLUXNET sites with different vegetation types and landscape characteristics. Simulated ozone deposition and flux from PX PSN are evaluated at one of the sites with ozone flux measurements. Overall, the PX PSN simulates LH as well as the PX Jarvis approach. The PX PSN, however, shows distinct advantages over the PX Jarvis approach for grassland that likely result from its treatment of C3 and C4 plants for CO2 assimilation. Simulations using Moderate Resolution Imaging Spectroradiometer (MODIS) leaf area index (LAI) rather than LAI measured at each site assess how the model would perform with grid averaged data used in WRF/CMAQ. MODIS LAI estimates degrade model performance at all sites but one site having exceptionally old and tall trees. Ozone deposition velocity and ozone flux along with LH

Coordination and trade-offs among hydraulic safety, efficiency and drought avoidance traits in Amazonian rainforest canopy tree species.

PubMed

Santiago, Louis S; De Guzman, Mark E; Baraloto, Christopher; Vogenberg, Jacob E; Brodie, Max; Hérault, Bruno; Fortunel, Claire; Bonal, Damien

2018-05-01

Predicting responses of tropical forests to climate change-type drought is challenging because of high species diversity. Detailed characterization of tropical tree hydraulic physiology is necessary to evaluate community drought vulnerability and improve model parameterization. Here, we measured xylem hydraulic conductivity (hydraulic efficiency), xylem vulnerability curves (hydraulic safety), sapwood pressure-volume curves (drought avoidance) and wood density on emergent branches of 14 common species of Eastern Amazonian canopy trees in Paracou, French Guiana across species with the densest and lightest wood in the plot. Our objectives were to evaluate relationships among hydraulic traits to identify strategies and test the ability of easy-to-measure traits as proxies for hard-to-measure hydraulic traits. Xylem efficiency was related to capacitance, sapwood water content and turgor loss point, and other drought avoidance traits, but not to xylem safety (P 50 ). Wood density was correlated (r = -0.57 to -0.97) with sapwood pressure-volume traits, forming an axis of hydraulic strategy variation. In contrast to drier sites where hydraulic safety plays a greater role, tropical trees in this humid tropical site varied along an axis with low wood density, high xylem efficiency and high capacitance at one end of the spectrum, and high wood density and low turgor loss point at the other. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

Spatiotemporal throughfall patterns beneath an urban tree row

NASA Astrophysics Data System (ADS)

Bogeholz, P.; Van Stan, J. T., II; Hildebrandt, A.; Friesen, J.; Dibble, M.; Norman, Z.

2016-12-01

Much recent research has focused on throughfall patterns in natural forests as they can influence the heterogeneity of surface ecohydrological and biogeochemical processes. However, to the knowledge of the authors, no work has assessed how urban forest structures affect the spatiotemporal variability of throughfall water flux. Urbanization greatly alters not only a significant portion of the land surface, but canopy structure, with the most typical urban forest configuration being landscaped tree rows along streets, swales, parking lot medians, etc. This study examines throughfall spatiotemporal patterns for a landscaped tree row of Pinus elliottii (Engelm., slash pine) on Georgia Southern University's campus (southeastern, USA) using 150 individual observations per storm. Throughfall correlation lengths beneath this tree row were similar to, but appeared to be more stable across storm size than, observations in past studies on natural forests. Individual tree overlap and the planting interval also may more strongly drive throughfall patterns in tree rows. Meteorological influences beyond storm magnitude (intensity, intermittency, wind conditions, and atmospheric moisture demand) are also examined.

Microscale Obstacle Resolving Air Quality Model Evaluation with the Michelstadt Case

PubMed Central

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7. PMID:24027450

Microscale obstacle resolving air quality model evaluation with the Michelstadt case.

PubMed

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7.

Assessing FPAR Source and Parameter Optimization Scheme in Application of a Diagnostic Carbon Flux Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, D P; Ritts, W D; Wharton, S

2009-02-26

The combination of satellite remote sensing and carbon cycle models provides an opportunity for regional to global scale monitoring of terrestrial gross primary production, ecosystem respiration, and net ecosystem production. FPAR (the fraction of photosynthetically active radiation absorbed by the plant canopy) is a critical input to diagnostic models, however little is known about the relative effectiveness of FPAR products from different satellite sensors nor about the sensitivity of flux estimates to different parameterization approaches. In this study, we used multiyear observations of carbon flux at four eddy covariance flux tower sites within the conifer biome to evaluate these factors.more » FPAR products from the MODIS and SeaWiFS sensors, and the effects of single site vs. cross-site parameter optimization were tested with the CFLUX model. The SeaWiFs FPAR product showed greater dynamic range across sites and resulted in slightly reduced flux estimation errors relative to the MODIS product when using cross-site optimization. With site-specific parameter optimization, the flux model was effective in capturing seasonal and interannual variation in the carbon fluxes at these sites. The cross-site prediction errors were lower when using parameters from a cross-site optimization compared to parameter sets from optimization at single sites. These results support the practice of multisite optimization within a biome for parameterization of diagnostic carbon flux models.« less

Development and evaluation of an ammonia bidirectional flux parameterization for air quality models

NASA Astrophysics Data System (ADS)

Pleim, Jonathan E.; Bash, Jesse O.; Walker, John T.; Cooter, Ellen J.

2013-05-01

is an important contributor to particulate matter in the atmosphere and can significantly impact terrestrial and aquatic ecosystems. Surface exchange between the atmosphere and biosphere is a key part of the ammonia cycle. New modeling techniques are being developed for use in air quality models that replace current ammonia emissions from fertilized crops and ammonia dry deposition with a bidirectional surface flux model including linkage to a detailed biogeochemical and farm management model. Recent field studies involving surface flux measurements over crops that predominate in North America have been crucial for extending earlier bidirectional flux models toward more realistic treatment of NH3 fluxes for croplands. Comparisons of the ammonia bidirection flux algorithm to both lightly fertilized soybeans and heavily fertilized corn demonstrate that the model can capture the magnitude and dynamics of observed ammonia fluxes, both net deposition and evasion, over a range of conditions with overall biases on the order of the uncertainty of the measurements. However, successful application to the field experiment in heavily fertilized corn required substantial modification of the model to include new parameterizations for in-soil diffusion resistance, ground quasi-laminar boundary layer resistance, and revised cuticular resistance that is dependent on in-canopy NH3 concentration and RH at the leaf surface. This new bidirectional flux algorithm has been incorporated in an air quality modeling system, which also includes an implementation of a soil nitrification model.

Investigating the processes of ammonia exchanges between the atmosphere and a corn canopy following Urea Ammonium Nitrate (UAN) fertilization with urease inhibitor NBPT

NASA Astrophysics Data System (ADS)

Lichiheb, N.; Myles, L.; Buban, M.; Heuer, M.; Nelson, A. J.; Koloutsou-Vakakis, S.; Rood, M. J.

2017-12-01

Agriculture is the main source of atmospheric emission of ammonia (NH3). The impact of these emissions on air quality is a rising subject of concern in the U.S. due to their adverse effect on human health and the environment. Emissions of NH3 from fertilized crop land occur as soon as fertilizer is applied on the farmed surface and emission can last from a few days to several weeks, depending on the properties of the specific fertilizer and environmental conditions. Because of the variability of these conditions, spatial and temporal variability of NH3 emissions is also variable and uncertain. Therefore, measurement of NH3 emissions is important for understanding the variables affecting the magnitude and temporal distribution of NH3 from fertilized fields. The aim of this study is to investigate the magnitude and the temporal characteristics of NH3 emission over a corn canopy fertilized with UAN and urease inhibitor NBPT, as well as their dependence on environmental variables. The NH3 fluxes above a corn canopy were measured using the flux-gradient (FG) and relaxed eddy accumulation (REA) methods over a period of approximately 3 months following fertilization in a corn field at the Energy Farm at the University of Illinois at Urbana-Champaign, IL, USA. NH3 fluxes were continuously monitored and averaged over 30 min with the FG method. For REA technique, NH3 fluxes were measured in four-hour periods during mornings and afternoons. During the first month after fertilization, prior to corn emergence and for relatively low LAI (<2), NH3 fluxes were positively correlated with soil surface temperature. Then the canopy recaptured NH3 emissions from the soil when the canopy has fully developed. A week after the fertilization, the highest volatilization peaks of 2300 ng Nm2s-1 using FG and 800 ng Nm2s-1 using REA were measured. The behavior of this fertilizer was explained by the urease inhibitor which reduced NH3 volatilization and delayed the time of the maximum rate of loss. This delay allows more time for the UAN to become incorporated into the soil. On the basis of this experimental study, urease inhibitor has a considerable effect on the rate and extent of NH3 volatilization. The effect of this inhibitor needs to be parameterized and implemented in the existing bi-directional NH3 exchange models for future models improvements.

Trends of urban surface temperature and heat island characteristics in the Mediterranean

NASA Astrophysics Data System (ADS)

Benas, Nikolaos; Chrysoulakis, Nektarios; Cartalis, Constantinos

2017-11-01

Urban air temperature studies usually focus on the urban canopy heat island phenomenon, whereby the city center experiences higher near surface air temperatures compared to its surrounding non-urban areas. The Land Surface Temperature (LST) is used instead of urban air temperature to identify the Surface Urban Heat Island (SUHI). In this study, the nighttime LST and SUHI characteristics and trends in the seventeen largest Mediterranean cities were investigated, by analyzing satellite observations for the period 2001-2012. SUHI averages and trends were based on an innovative approach of comparing urban pixels to randomly selected non-urban pixels, which carries the potential to better standardize satellite-derived SUHI estimations. A positive trend for both LST and SUHI for the majority of the examined cities was documented. Furthermore, a 0.1 °C decade-1 increase in urban LST corresponded to an increase in SUHI by about 0.04 °C decade-1. A longitudinal differentiation was found in the urban LST trends, with higher positive values appearing in the eastern Mediterranean. Examination of urban infrastructure and development factors during the same period revealed correlations with SUHI trends, which can be used to explain differences among cities. However, the majority of the cities examined show considerably increased trends in terms of the enhancement of SUHI. These findings are considered important so as to promote sustainable urbanization, as well as to support the development of heat island adaptation and mitigation plans in the Mediterranean.

Model analysis of urbanization impacts on boundary layer meteorology under hot weather conditions: a case study of Nanjing, China

NASA Astrophysics Data System (ADS)

Chen, Lei; Zhang, Meigen; Wang, Yongwei

2016-08-01

The Weather Research and Forecasting (WRF) model, configured with a single-layer urban canopy model, was employed to investigate the influence of urbanization on boundary layer meteorological parameters during a long-lasting heat wave. This study was conducted over Nanjing city, East China, from 26 July to 4 August 2010. The impacts of urban expansion and anthropogenic heat (AH) release were simulated to quantify their effects on 2-m temperature, 2-m water vapor mixing ratio, and 10-m wind speed and heat stress index. Urban sprawl increased the daily 2-m temperature in urbanized areas by around 1.6 °C and decreased the urban diurnal temperature range (DTR) by 1.24 °C. The contribution of AH release to the atmospheric warming was nearly 22 %, but AH had little influence on the DTR. The urban regional mean surface wind speed decreased by about 0.4 m s-1, and this decrease was successfully simulated from the surface to 300 m. The influence of urbanization on 2-m water vapor mixing ratio was significant over highly urbanized areas with a decrease of 1.1-1.8 g kg-1. With increased urbanization ratio, the duration of the inversion layer was about 4 h shorter, and the lower atmospheric layer was less stable. Urban heat island (UHI) intensity was significantly enhanced when synthesizing both urban sprawl and AH release and the daily mean UHI intensity increased by 0.74 °C. Urbanization increased the time under extreme heat stress (about 40 %) and worsened the living environment in urban areas.

Tree Productivity Enhanced with Conversion from Forest to Urban Land Covers.

PubMed

Briber, Brittain M; Hutyra, Lucy R; Reinmann, Andrew B; Raciti, Steve M; Dearborn, Victoria K; Holden, Christopher E; Dunn, Allison L

2015-01-01

Urban areas are expanding, changing the structure and productivity of landscapes. While some urban areas have been shown to hold substantial biomass, the productivity of these systems is largely unknown. We assessed how conversion from forest to urban land uses affected both biomass structure and productivity across eastern Massachusetts. We found that urban land uses held less than half the biomass of adjacent forest expanses with a plot level mean biomass density of 33.5 ± 8.0 Mg C ha(-1). As the intensity of urban development increased, the canopy cover, stem density, and biomass decreased. Analysis of Quercus rubra tree cores showed that tree-level basal area increment nearly doubled following development, increasing from 17.1 ± 3.0 to 35.8 ± 4.7 cm(2) yr(-1). Scaling the observed stem densities and growth rates within developed areas suggests an aboveground biomass growth rate of 1.8 ± 0.4 Mg C ha(-1) yr(-1), a growth rate comparable to nearby, intact forests. The contrasting high growth rates and lower biomass pools within urban areas suggest a highly dynamic ecosystem with rapid turnover. As global urban extent continues to grow, cities consider climate mitigation options, and as the verification of net greenhouse gas emissions emerges as critical for policy, quantifying the role of urban vegetation in regional-to-global carbon budgets will become ever more important.

Tree Productivity Enhanced with Conversion from Forest to Urban Land Covers

PubMed Central

Briber, Brittain M.; Hutyra, Lucy R.; Reinmann, Andrew B.; Raciti, Steve M.; Dearborn, Victoria K.; Holden, Christopher E.; Dunn, Allison L.

2015-01-01

Urban areas are expanding, changing the structure and productivity of landscapes. While some urban areas have been shown to hold substantial biomass, the productivity of these systems is largely unknown. We assessed how conversion from forest to urban land uses affected both biomass structure and productivity across eastern Massachusetts. We found that urban land uses held less than half the biomass of adjacent forest expanses with a plot level mean biomass density of 33.5 ± 8.0 Mg C ha-1. As the intensity of urban development increased, the canopy cover, stem density, and biomass decreased. Analysis of Quercus rubra tree cores showed that tree-level basal area increment nearly doubled following development, increasing from 17.1 ± 3.0 to 35.8 ± 4.7 cm2 yr-1. Scaling the observed stem densities and growth rates within developed areas suggests an aboveground biomass growth rate of 1.8 ± 0.4 Mg C ha-1 yr-1, a growth rate comparable to nearby, intact forests. The contrasting high growth rates and lower biomass pools within urban areas suggest a highly dynamic ecosystem with rapid turnover. As global urban extent continues to grow, cities consider climate mitigation options, and as the verification of net greenhouse gas emissions emerges as critical for policy, quantifying the role of urban vegetation in regional-to-global carbon budgets will become ever more important. PMID:26302444

Volumetric visualization of multiple-return LIDAR data: Using voxels

USGS Publications Warehouse

Stoker, Jason M.

2009-01-01

Elevation data are an important component in the visualization and analysis of geographic information. The creation and display of 3D models representing bare earth, vegetation, and surface structures have become a major focus of light detection and ranging (lidar) remote sensing research in the past few years. Lidar is an active sensor that records the distance, or range, of a laser usually fi red from an airplane, helicopter, or satellite. By converting the millions of 3D lidar returns from a system into bare ground, vegetation, or structural elevation information, extremely accurate, high-resolution elevation models can be derived and produced to visualize and quantify scenes in three dimensions. These data can be used to produce high-resolution bare-earth digital elevation models; quantitative estimates of vegetative features such as canopy height, canopy closure, and biomass; and models of urban areas such as building footprints and 3D city models.

Multiple health benefits of urban tree canopy: The mounting evidence for a green prescription.

PubMed

Ulmer, Jared M; Wolf, Kathleen L; Backman, Desiree R; Tretheway, Raymond L; Blain, Cynthia Ja; O'Neil-Dunne, Jarlath Pm; Frank, Lawrence D

2016-11-01

The purpose of this study was to enhance the understanding of the health-promoting potential of trees in an urbanized region of the United States. This was done using high-resolution LiDAR and imagery data to quantify tree cover within 250m of the residence of 7910 adult participants in the California Health Interview Survey, then testing for main and mediating associations between tree cover and multiple health measures. The results indicated that more neighborhood tree cover, independent from green space access, was related to better overall health, primarily mediated by lower overweight/obesity and better social cohesion, and to a lesser extent by less type 2 diabetes, high blood pressure, and asthma. These findings suggest an important role for trees and nature in improving holistic population health in urban areas. Copyright © 2016 Elsevier Ltd. All rights reserved.

Turbulence and Air Exchange in a Two-Dimensional Urban Street Canyon Between Gable Roof Buildings

NASA Astrophysics Data System (ADS)

Garau, Michela; Badas, Maria Grazia; Ferrari, Simone; Seoni, Alessandro; Querzoli, Giorgio

2018-04-01

We experimentally investigate the effect of a typical building covering: the gable roof, on the flow and air exchange in urban canyons. In general, the morphology of the urban canopy is very varied and complex, depending on a large number of factors, such as building arrangement, or the morphology of the terrain. Therefore we focus on a simple, prototypal shape, the two-dimensional canyon, with the aim of elucidating some fundamental phenomena driving the street-canyon ventilation. Experiments are performed in a water channel, over an array of identical prismatic obstacles representing an idealized urban canopy. The aspect ratio, i.e. canyon-width to building-height ratio, ranges from 1 to 6. Gable roof buildings with 1:1 pitch are compared with flat roofed buildings. Velocity is measured using a particle-image-velocimetry technique with flow dynamics discussed in terms of mean flow and second- and third-order statistical moments of the velocity. The ventilation is interpreted by means of a simple well-mixed box model and the outflow rate and mean residence time are computed. Results show that gable roofs tend to delay the transition from the skimming-flow to the wake-interference regime and promote the development of a deeper and more turbulent roughness layer. The presence of a gable roof significantly increases the momentum flux, especially for high packing density. The air exchange is improved compared to the flat roof buildings, and the beneficial effect is more significant for narrow canyons. Accordingly, for unit aspect ratio gable roofs reduce the mean residence time by a factor of 0.37 compared to flat roofs, whereas the decrease is only by a factor of 0.9 at the largest aspect ratio. Data analysis indicates that, for flat roof buildings, the mean residence time increases by 30% when the aspect ratio is decreased from 6 to 2, whereas this parameter is only weakly dependent on aspect ratio in the case of gable roofs.

Mapping urban forest tree species using IKONOS imagery: preliminary results.

PubMed

Pu, Ruiliang

2011-01-01

A stepwise masking system with high-resolution IKONOS imagery was developed to identify and map urban forest tree species/groups in the City of Tampa, Florida, USA. The eight species/groups consist of sand live oak (Quercus geminata), laurel oak (Quercus laurifolia), live oak (Quercus virginiana), magnolia (Magnolia grandiflora), pine (species group), palm (species group), camphor (Cinnamomum camphora), and red maple (Acer rubrum). The system was implemented with soil-adjusted vegetation index (SAVI) threshold, textural information after running a low-pass filter, and brightness threshold of NIR band to separate tree canopies from non-vegetated areas from other vegetation types (e.g., grass/lawn) and to separate the tree canopies into sunlit and shadow areas. A maximum likelihood classifier was used to identify and map forest type and species. After IKONOS imagery was preprocessed, a total of nine spectral features were generated, including four spectral bands, three hue-intensity-saturation indices, one SAVI, and one texture image. The identified and mapped results were examined with independent ground survey data. The experimental results indicate that when classifying all the eight tree species/ groups with the high-resolution IKONOS image data, the identifying accuracy was very low and could not satisfy a practical application level, and when merging the eight species/groups into four major species/groups, the average accuracy is still low (average accuracy = 73%, overall accuracy = 86%, and κ = 0.76 with sunlit test samples). Such a low accuracy of identifying and mapping the urban tree species/groups is attributable to low spatial resolution IKONOS image data relative to tree crown size, to complex and variable background spectrum impact on crown spectra, and to shadow/shaded impact. The preliminary results imply that to improve the tree species identification accuracy and achieve a practical application level in urban area, multi-temporal (multi-seasonal) or hyperspectral data image data should be considered for use in the future.

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

Where the woodland ends: How edges affect landscape structure and physiological responses of Quercus agrifolia

NASA Astrophysics Data System (ADS)

de Chant, Timothy Paul

Forests and woodlands are integral parts of ecosystems across the globe, but they are threatened by a variety of factors, including urbanization and introduced forest pathogens. These two forces are fundamentally altering ecosystems, both by removing forest cover and reshaping landscapes. Comprehending how these two processes have changed forest ecosystems is an important step toward understanding how the affected systems will function in the future. I investigated the range of edge effects that result from disturbance brought about by forest pathogens and urbanization in two coastal oak woodlands in Marin County, California. Oak woodlands are a dynamic part of California's landscape, reacting to changes in their biotic and abiotic environments across a range of spatial and temporal scales. Sudden Oak Death, caused by the introduced forest pathogen Phytophthora ramorum, has led to widespread mortality of many tree species in California's oak woodlands. I investigated how the remaining trees respond to such rapid changes in canopy structure (Chapter 2), and my results revealed a forest canopy quick to respond to the new openings. Urbanization, another disturbance regime, operates on a longer time scale. Immediately following urban development, forest edges are strikingly linear, but both forest processes and homeowner actions likely work in concert to disrupt the straight edge (Chapter 3). Forest edges grew more sinuous within 14 years of the initial disturbance, and continued to do so for the remainder of the study, another 21 years. Individual Quercus agrifolia trees also respond to urban edges decades after disturbance (Chapter 4), and their reaction is reflected in declining stable carbon isotope values (delta13C). This change suggests trees may have increased their stomatal conductance in response to greater water availability, reduced their photosynthetic rate as a result of stress, or some combination of both. Edges have far reaching and long lasting effects on forest structure and function. Investigations of their impacts on multiple spatial and temporal scales are important in determining the range of effects they have on forest ecosystems. Studies that combine remote sensing, geographic information systems, and field studies may help us understand the ecological consequences of forest edges.

Modeling particle nucleation and growth over northern California during the 2010 CARES campaign

NASA Astrophysics Data System (ADS)

Lupascu, A.; Easter, R.; Zaveri, R.; Shrivastava, M.; Pekour, M.; Tomlinson, J.; Yang, Q.; Matsui, H.; Hodzic, A.; Zhang, Q.; Fast, J. D.

2015-11-01

Accurate representation of the aerosol lifecycle requires adequate modeling of the particle number concentration and size distribution in addition to their mass, which is often the focus of aerosol modeling studies. This paper compares particle number concentrations and size distributions as predicted by three empirical nucleation parameterizations in the Weather Research and Forecast coupled with chemistry (WRF-Chem) regional model using 20 discrete size bins ranging from 1 nm to 10 μm. Two of the parameterizations are based on H2SO4, while one is based on both H2SO4 and organic vapors. Budget diagnostic terms for transport, dry deposition, emissions, condensational growth, nucleation, and coagulation of aerosol particles have been added to the model and are used to analyze the differences in how the new particle formation parameterizations influence the evolving aerosol size distribution. The simulations are evaluated using measurements collected at surface sites and from a research aircraft during the Carbonaceous Aerosol and Radiative Effects Study (CARES) conducted in the vicinity of Sacramento, California. While all three parameterizations captured the temporal variation of the size distribution during observed nucleation events as well as the spatial variability in aerosol number, all overestimated by up to a factor of 2.5 the total particle number concentration for particle diameters greater than 10 nm. Using the budget diagnostic terms, we demonstrate that the combined H2SO4 and low-volatility organic vapor parameterization leads to a different diurnal variability of new particle formation and growth to larger sizes compared to the parameterizations based on only H2SO4. At the CARES urban ground site, peak nucleation rates are predicted to occur around 12:00 Pacific (local) standard time (PST) for the H2SO4 parameterizations, whereas the highest rates were predicted at 08:00 and 16:00 PST when low-volatility organic gases are included in the parameterization. This can be explained by higher anthropogenic emissions of organic vapors at these times as well as lower boundary-layer heights that reduce vertical mixing. The higher nucleation rates in the H2SO4-organic parameterization at these times were largely offset by losses due to coagulation. Despite the different budget terms for ultrafine particles, the 10-40 nm diameter particle number concentrations from all three parameterizations increased from 10:00 to 14:00 PST and then decreased later in the afternoon, consistent with changes in the observed size and number distribution. We found that newly formed particles could explain up to 20-30 % of predicted cloud condensation nuclei at 0.5 % supersaturation, depending on location and the specific nucleation parameterization. A sensitivity simulation using 12 discrete size bins ranging from 1 nm to 10 μm diameter gave a reasonable estimate of particle number and size distribution compared to the 20 size bin simulation, while reducing the associated computational cost by ~ 36 %.

Characteristics of urban natural areas influencing winter bird use in southern Ontario, Canada.

PubMed

Smith, Paul G R

2007-03-01

Characteristics of urban natural areas and surrounding landscapes were identified that best explain winter bird use for 28 urban natural areas in southern Ontario, Canada. The research confirms for winter birds the importance of area (size) and natural vegetation, rather than managed, horticultural parkland, within urban natural areas as well as percent urban land use and natural habitat in surrounding landscapes. Alien bird density and percent ground feeding species increased with percent surrounding urban land use. Higher percent forest cover was associated with higher percentages of forest, bark feeding, small (<20 g) and insectivorous species. Natural area size (ha) was related to higher species richness, lower evenness and higher percentages of insectivorous, forest interior, area-sensitive, upper canopy, bark feeding, and non-resident species. Higher number of habitat types within natural areas and percent natural habitat in surrounding landscapes were also associated with higher species richness. Common, resident bird species dominated small areas (<6.5 ha), while less common non-residents increased with area, indicative of a nested distribution. Areas at least 6.5 ha and more generally >20 ha start to support some area-sensitive species. Areas similar to rural forests had >25% insectivores, >25% forest interior species, >25% small species, and <5% alien species. Indicator species separated urban natural areas from rural habitats and ordination placed urban natural areas along a gradient between urban development and undisturbed, rural forests. More attention is needed on issues of winter bird conservation in urban landscapes.

Characteristics of Urban Natural Areas Influencing Winter Bird Use in Southern Ontario, Canada

NASA Astrophysics Data System (ADS)

Smith, Paul G. R.

2007-03-01

Characteristics of urban natural areas and surrounding landscapes were identified that best explain winter bird use for 28 urban natural areas in southern Ontario, Canada. The research confirms for winter birds the importance of area (size) and natural vegetation, rather than managed, horticultural parkland, within urban natural areas as well as percent urban land use and natural habitat in surrounding landscapes. Alien bird density and percent ground feeding species increased with percent surrounding urban land use. Higher percent forest cover was associated with higher percentages of forest, bark feeding, small (<20 g) and insectivorous species. Natural area size (ha) was related to higher species richness, lower evenness and higher percentages of insectivorous, forest interior, area-sensitive, upper canopy, bark feeding, and non-resident species. Higher number of habitat types within natural areas and percent natural habitat in surrounding landscapes were also associated with higher species richness. Common, resident bird species dominated small areas (<6.5 ha), while less common non-residents increased with area, indicative of a nested distribution. Areas at least 6.5 ha and more generally >20 ha start to support some area-sensitive species. Areas similar to rural forests had >25% insectivores, >25% forest interior species, >25% small species, and <5% alien species. Indicator species separated urban natural areas from rural habitats and ordination placed urban natural areas along a gradient between urban development and undisturbed, rural forests. More attention is needed on issues of winter bird conservation in urban landscapes.

Ground Field-Based Hyperspectral Imaging: A Preliminary Study to Assess the Potential of Established Vegetation Indices to Infer Variation in Water-Use Efficiency.

NASA Astrophysics Data System (ADS)

Pelech, E. A.; McGrath, J.; Pederson, T.; Bernacchi, C.

2017-12-01

Increases in the global average temperature will consequently induce a higher occurrence of severe environmental conditions such as drought on arable land. To mitigate these threats, crops for fuel and food must be bred for higher water-use efficiencies (WUE). Defining genomic variation through high-throughput phenotypic analysis in field conditions has the potential to relieve the major bottleneck in linking desirable genetic traits to the associated phenotypic response. This can subsequently enable breeders to create new agricultural germplasm that supports the need for higher water-use efficient crops. From satellites to field-based aerial and ground sensors, the reflectance properties of vegetation measured by hyperspectral imaging is becoming a rapid high-throughput phenotyping technique. A variety of physiological traits can be inferred by regression analysis with leaf reflectance which is controlled by the properties and abundance of water, carbon, nitrogen and pigments. Although, given that the current established vegetation indices are designed to accentuate these properties from spectral reflectance, it becomes a challenge to infer relative measurements of WUE at a crop canopy scale without ground-truth data collection. This study aims to correlate established biomass and canopy-water-content indices with ground-truth data. Five bioenergy sorghum genotypes (Sorghum bicolor L. Moench) that have differences in WUE and wild-type Tobacco (Nicotiana tabacum var. Samsun) under irrigated and rainfed field conditions were examined. A linear regression analysis was conducted to determine if variation in canopy water content and biomass, driven by natural genotypic and artificial treatment influences, can be inferred using established vegetation indices. The results from this study will elucidate the ability of ground field-based hyperspectral imaging to assess variation in water content, biomass and water-use efficiency. This can lead to improved opportunities to select ideal genotypes for an increasing water-limited environment and to help parameterize and validate terrestrial vegetation models that require a better representation of genetic variation within crop species.

How vertical patterns in leaf traits shift seasonally and the implications for modeling canopy photosynthesis in a temperate deciduous forest.

PubMed

Coble, Adam P; VanderWall, Brittany; Mau, Alida; Cavaleri, Molly A

2016-09-01

Leaf functional traits are used in modeling forest canopy photosynthesis (Ac) due to strong correlations between photosynthetic capacity, leaf mass per area (LMA) and leaf nitrogen per area (Narea). Vertical distributions of these traits may change over time in temperate deciduous forests as a result of acclimation to light, which may result in seasonal changes in Ac To assess both spatial and temporal variations in key traits, we measured vertical profiles of Narea and LMA from leaf expansion through leaf senescence in a sugar maple (Acer saccharum Marshall) forest. To investigate mechanisms behind coordinated changes in leaf morphology and function, we also measured vertical variation in leaf carbon isotope composition (δ(13)C), predawn turgor pressure, leaf water potential and osmotic potential. Finally, we assessed potential biases in Ac estimations by parameterizing models with and without vertical and seasonal Narea variations following leaf expansion. Our data are consistent with the hypothesis that hydrostatic constraints on leaf morphology drive the vertical increase in LMA with height early in the growing season; however, LMA in the upper canopy continued to increase over time during light acclimation, indicating that light is primarily driving gradients in LMA later in the growing season. Models with no seasonal variation in Narea overestimated Ac by up to 11% early in the growing season, while models with no vertical variation in Narea overestimated Ac by up to 60% throughout the season. According to the multilayer model, the upper 25% of leaf area contributed to over 50% of Ac, but when gradients of intercellular CO2, as estimated from δ(13)C, were accounted for, the upper 25% of leaf area contributed to 26% of total Ac Our results suggest that ignoring vertical variation of key traits can lead to considerable overestimation of Ac. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Developing Land Surface Type Map with Biome Classification Scheme Using Suomi NPP/JPSS VIIRS Data

NASA Astrophysics Data System (ADS)

Zhang, Rui; Huang, Chengquan; Zhan, Xiwu; Jin, Huiran

2016-08-01

Accurate representation of actual terrestrial surface types at regional to global scales is an important element for a wide range of applications, such as land surface parameterization, modeling of biogeochemical cycles, and carbon cycle studies. In this study, in order to meet the requirement of the retrieval of global leaf area index (LAI) and fraction of photosynthetically active radiation absorbed by the vegetation (fPAR) and other studies, a global map generated from Suomi National Polar- orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) surface reflectance data in six major biome classes based on their canopy structures, which include: Grass/Cereal Crops, Shrubs, Broadleaf Crops, Savannas, Broadleaf Forests, and Needleleaf Forests, was created. The primary biome classes were converted from an International Geosphere-Biosphere Program (IGBP) legend global surface type data that was created in previous study, and the separation of two crop types are based on a secondary classification.

Evapotranspiration under advective conditions.

PubMed

Figuerola, Patricia I; Berliner, Pedro R

2005-07-01

Arid and semi-arid regions are heterogeneous landscapes in which irrigated fields are surrounded by arid areas. The advection of sensible heat flux from dry surfaces is a significant source of energy that has to be taken into consideration when evaluating the evaporation from crops growing in these areas. The basic requirement of most of the common methods for estimating evapotranspiration [Bowen ratio, aerodynamic and Penman-Monteith (PM) equation] is that the horizontal fluxes of sensible and latent heat are negligible when compared to the corresponding vertical fluxes. We carried out measurements above an irrigated tomato field in a desert area. Latent and sensible heat fluxes were measured using a four-level Bowen machine with aspirated psychrometers. Our results indicate that under advective conditions only measurements carried out in the lowest layer are satisfactory for the estimation of latent heat fluxes and that the use of the PM equation with an appropriately parameterized canopy resistance may be preferable.

Effects of urban tree canopy loss on land surface temperature magnitude and timing

NASA Astrophysics Data System (ADS)

Elmes, Arthur; Rogan, John; Williams, Christopher; Ratick, Samuel; Nowak, David; Martin, Deborah

2017-06-01

Urban Tree Canopy (UTC) plays an important role in moderating the Surface Urban Heat Island (SUHI) effect, which poses threats to human health due to substantially increased temperatures relative to rural areas. UTC coverage is associated with reduced urban temperatures, and therefore benefits both human health and reducing energy use in cities. Measurement of this relationship relies on accurate, fine spatial resolution UTC mapping, and on time series analysis of Land Surface Temperatures (LST). The City of Worcester, Massachusetts underwent extensive UTC loss and gain during the relatively brief period from 2008 to 2015, providing a natural experiment to measure the UTC/LST relationship. This paper consists of two elements to this end. First, it presents methods to map UTC in urban and suburban locations at fine spatial resolution (∼0.5 m) using image segmentation of a fused Lidar/WorldView-2 dataset, in order to show UTC change over time. Second, the areas of UTC change are used to explore changes in LST magnitude and seasonal variability using a time series of all available Landsat data for the study area over the eight-year period from 2007 to 2015. Fractional UTC change per unit area was determined using fine resolution UTC maps for 2008, 2010, and 2015, covering the period of large-scale tree loss and subsequent planting. LST changes were measured across a series of net UTC change bins, providing a relationship between UTC net change and LST trend. LST was analyzed for both monotonic trends over time and changes to seasonal magnitude and timing, using Theil-Sen slopes and Seasonal Trend Analysis (STA), respectively. The largest magnitudes of UTC loss occurred in residential neighborhoods, causing increased exposure of impervious (road) and pervious (grass) surfaces. Net UTC loss showed higher monotonic increases in LST than persistence and gain areas. STA indicated that net UTC loss was associated greater difference between 2008 and 2015 seasonal temperature curves than persistence areas, and also larger peak LST values, with peak increases ranging from 1 to 6 °C. Timing of summer warm period was extended in UTC loss areas by up to 15 days. UTC gain provided moderate LST mitigation, with lower monotonic trends, lower peak temperatures, and smaller seasonal curve changes than both persistence and loss locations. This study shows that urban trees mitigate the magnitude and timing of the surface urban heat island effect, even in suburban areas with less proportional impervious coverage than the dense urban areas traditionally associated with SUHI. Trees can therefore be seen as an effective means of offsetting the energy-intensive urban heat island effect.

The influence of vegetation on the horizontal and vertical distribution of pollutants in a street canyon.

PubMed

Salmond, J A; Williams, D E; Laing, G; Kingham, S; Dirks, K; Longley, I; Henshaw, G S

2013-01-15

Space constraints in cities mean that there are only limited opportunities for increasing tree density within existing urban fabric and it is unclear whether the net effect of increased vegetation in street canyons is beneficial or detrimental to urban air quality at local scales. This paper presents data from a field study undertaken in Auckland, New Zealand designed to determine the local impact of a deciduous tree canopy on the distribution of the oxides of nitrogen within a street canyon. The results showed that the presence of leaves on the trees had a marked impact on the transport of pollutants and led to a net accumulation of pollutants in the canyon below the tree tops. The incidence and magnitude of temporally localised spikes in pollutant concentration were reduced within the tree canopy itself. A significant difference in pollutant concentrations with height was not observed when leaves were absent. Analysis of the trends in concentration associated with different wind directions showed a smaller difference between windward and leeward sides when leaves were on the trees. A small relative increase in concentrations on the leeward side was observed during leaf-on relative to leaf-off conditions as predicted by previous modelling studies. However the expected reduction in concentrations on the windward side was not observed. The results suggest that the presence of leaves on the trees reduces the upwards transport of fresh vehicle emissions, increases the storage of pollutants within the canopy space and reduces the penetration of clean air downwards from aloft. Differences observed between NO and NO(2) concentrations could not be accounted for by dispersion processes alone, suggesting that there may also be some changes in the chemistry of the atmosphere associated with the presence of leaves on the trees. Copyright © 2012 Elsevier B.V. All rights reserved.

Surface water areas significantly impacted 2014 dengue outbreaks in Guangzhou, China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Huaiyu; Huang, Shanqian

Dengue transmission in urban areas is strongly influenced by a range of biological and environmental factors, yet the key drivers still need further exploration. To better understand mechanisms of environment–mosquito–urban dengue transmission, we propose an empirical model parameterized and cross-validated from a unique dataset including viral gene sequences, vector dynamics and human dengue cases in Guangzhou, China, together with a 36-year urban environmental change maps investigated by spatiotemporal satellite image fusion. The dengue epidemics in Guangzhou are highly episodic and were not associated with annual rainfall over time. Our results indicate that urban environmental changes, especially variations in surface areamore » covered by water in urban areas, can substantially alter the virus population and dengue transmission. The recent severe dengue outbreaks in Guangzhou may be due to the surge in an artificial lake construction, which could increase infection force between vector (mainly Aedes albopictus) and host when urban water area significantly increased. Impacts of urban environmental change on dengue dynamics may not have been thoroughly investigated in the past studies and more work needs to be done to better understand the consequences of urbanization processes in our changing world. - Highlights: • Urban dengue outbreak is associated with water area in Guangzhou, 1978–2014. • Surface water area can alter population size of dengue virus in urban area. • Urban dengue outbreak is not associated with annual rainfall in Guangzhou. • Spatiotemporal satellite image fusion can investigate urban environmental change. • Urban environmental change could induce virus, vector, and dengue epidemic change.« less

A sub-canopy structure for simulating oil palm in the Community Land Model (CLM-Palm): phenology, allocation and yield

NASA Astrophysics Data System (ADS)

Fan, Y.; Roupsard, O.; Bernoux, M.; Le Maire, G.; Panferov, O.; Kotowska, M. M.; Knohl, A.

2015-11-01

In order to quantify the effects of forests to oil palm conversion occurring in the tropics on land-atmosphere carbon, water and energy fluxes, we develop a new perennial crop sub-model CLM-Palm for simulating a palm plant functional type (PFT) within the framework of the Community Land Model (CLM4.5). CLM-Palm is tested here on oil palm only but is meant of generic interest for other palm crops (e.g., coconut). The oil palm has monopodial morphology and sequential phenology of around 40 stacked phytomers, each carrying a large leaf and a fruit bunch, forming a multilayer canopy. A sub-canopy phenological and physiological parameterization is thus introduced so that each phytomer has its own prognostic leaf growth and fruit yield capacity but with shared stem and root components. Phenology and carbon and nitrogen allocation operate on the different phytomers in parallel but at unsynchronized steps, separated by a thermal period. An important phenological phase is identified for the oil palm - the storage growth period of bud and "spear" leaves which are photosynthetically inactive before expansion. Agricultural practices such as transplanting, fertilization and leaf pruning are represented. Parameters introduced for the oil palm were calibrated and validated with field measurements of leaf area index (LAI), yield and net primary production (NPP) from Sumatra, Indonesia. In calibration with a mature oil palm plantation, the cumulative yields from 2005 to 2014 matched notably well between simulation and observation (mean percentage error = 3 %). Simulated inter-annual dynamics of PFT-level and phytomer-level LAI were both within the range of field measurements. Validation from eight independent oil palm sites shows the ability of the model to adequately predict the average leaf growth and fruit yield across sites and sufficiently represent the significant nitrogen- and age-related site-to-site variability in NPP and yield. Results also indicate that seasonal dynamics of yield and remaining small-scale site-to-site variability of NPP are driven by processes not yet implemented in the model or reflected in the input data. The new sub-canopy structure and phenology and allocation functions in CLM-Palm allow exploring the effects of tropical land-use change, from natural ecosystems to oil palm plantations, on carbon, water and energy cycles and regional climate.

Carbonyl sulfide (COS) as a tracer for canopy photosynthesis, transpiration and stomatal conductance: potential and limitations

PubMed Central

Wohlfahrt, Georg; Brilli, Federico; Hörtnagl, Lukas; Xu, Xiaobin; Bingemer, Heinz; Hansel, Armin; Loreto, Francesco

2012-01-01

The theoretical basis for the link between the leaf exchange of carbonyl sulfide (COS), carbon dioxide (CO2) and water vapour (H2O) and the assumptions that need to be made in order to use COS as a tracer for canopy net photosynthesis, transpiration and stomatal conductance, are reviewed. The ratios of COS to CO2 and H2O deposition velocities used to this end are shown to vary with the ratio of the internal to ambient CO2 and H2O mole fractions and the relative limitations by boundary layer, stomatal and internal conductance for COS. It is suggested that these deposition velocity ratios exhibit considerable variability, a finding that challenges current parameterizations, which treat these as vegetation-specific constants. COS is shown to represent a better tracer for CO2 than H2O. Using COS as a tracer for stomatal conductance is hampered by our present poor understanding of the leaf internal conductance to COS. Estimating canopy level CO2 and H2O fluxes requires disentangling leaf COS exchange from other ecosystem sources/sinks of COS. We conclude that future priorities for COS research should be to improve the quantitative understanding of the variability in the ratios of COS to CO2 and H2O deposition velocities and the controlling factors, and to develop operational methods for disentangling ecosystem COS exchange into contributions by leaves and other sources/sinks. To this end, integrated studies, which concurrently quantify the ecosystem-scale CO2, H2O and COS exchange and the corresponding component fluxes, are urgently needed. We investigate the potential of carbonyl sulfide (COS) for being used as a tracer for canopy net photosynthesis, transpiration and stomatal conductance by examining the theoretical basis of the link between leaf COS, carbon dioxide (CO2) and water vapour (H2O) exchange. Our analysis identifies several limitations that need to be overcome to this end, however at present we lack appropriate ecosystem-scale field measurements for assessing their practical significance. It however appears that COS represents a better tracer for CO2 than H2O. Concurrent measurements of ecosystem scale COS, CO2 and H2O exchange are advocated. PMID:22017586

Future Urban Climate Projection in A Tropical Megacity Based on Global and Regional Scenarios

NASA Astrophysics Data System (ADS)

Darmanto, N. S.; Varquez, A. C. G.; Kanda, M.

2017-12-01

Cities in Asian developing countries experience rapid transformation in urban morphology and energy consumption, which correspondingly affects urban climate. Weather Research and Forecasting (WRF) Model coupled with improved single-layer urban canopy model incorporating realistic distribution of urban parameters and anthropogenic heat emission (AHE) in the tropic Jakarta Greater Area was conducted. Simulation was conducted during the dry months from 2006 to 2015 and agreed well with point and satellite observation. The same technology coupled with pseudo global warming (PGW) method based on representative concentration pathways (RCP) scenario 2.6 and 8.5 was conducted to produce futuristic climate condition in 2050. Projected urban morphology and AHE in 2050s were constructed using regional urban growing model with shared socioeconomic pathways (SSP) among its inputs. Compact future urban configuration, based on SSP1, was coupled to RCP2.6. Unrestrained future urban configuration, based on SSP3, was coupled to RCP8.5. Results show that background warming from RCP 2.6 and 8.5 will increase background temperature by 0.55°C and 1.2°C throughout the region, respectively. Future projection of urban sprawl results to an additional 0.3°C and 0.5°C increase on average, with maximum increase of 1.1°C and 1.3°C due to urban effect for RCP2.6/compact and RCP8.5/unrestrained, respectively. Higher moisture content in urban area is indicated in the future due to higher evaporation. Change in urban roughness is likely affect slower wind velocity in urban area and sea breeze front inland penetration the future compare with current condition. Acknowledgement: This research was supported by the Environment Research and Technology Development Fund (S-14) of the Ministry of the Environment, Japan.

Comparison of selected approaches for urban roughness determination based on voronoi cells.

PubMed

Ketterer, Christine; Gangwisch, Marcel; Fröhlich, Dominik; Matzarakis, Andreas

2017-01-01

Wind speed is reduced above urban areas due to their high aerodynamic roughness. This not only holds for above the urban canopy. The local vertical wind profile is modified. Aerodynamic roughness (both roughness length and displacement height) therefore is relevant for many fields within human biometeorology, e.g. for the identification of ventilation paths, the concentration and dispersion of air pollutants at street level or to simulate wind speed and direction in urban environments and everything depending on them. Roughness, thus, also shows strong influence on human thermal comfort. Currently, roughness parameters are mostly estimated using classifications. However, such classifications only provide limited assessment of roughness in urban areas. In order to calculate spatially resolved roughness on the micro-scale, three different approaches were implemented in the SkyHelios model. For all of them, the urban area is divided into reference areas for each of the obstacles using a voronoi diagram. The three approaches are based on building and [+one of them also on] vegetation (trees and forests) data. They were compared for the city of Stuttgart, Germany. Results show that the approach after Bottema and Mestayer (J Wind Eng Ind Aerodyn 74-76:163-173 1998) on the spatial basis of a voronoi diagram provides the most plausible results.

Focusing on the big picture: urban vegetation and eco ...

EPA Pesticide Factsheets

Trees and vegetation can be key components of urban green infrastructure and green spaces such as parks and residential yards. Large trees, characterized by broad canopies, and high leaf and stem volumes, can intercept a substantial amount of stormwater while promoting evapotranspiration and reducing stormwater runoff and pollutant loads. Urban vegetation cover, height, and volume are likely to be affected not only by local climatic characteristics, but also by complex socio-economic dynamics resulting from management practices and resident’s preferences. We examine the benefits provided by private greenspace and present preliminary findings related to the climatic and socio-economic drivers correlated with structural complexity of residential urban vegetation. We use laser (LiDAR) and multispectral remotely-sensed data collected throughout 1400+ neighborhoods and 1.2+ million residential yards across 8 US cities to carry out this analysis. We discuss principles and opportunities to enhance stormwater management using residential greenspace, as well as the larger implications for decentralized stormwater management at city-wide scale. We discuss principles and opportunities to enhance stormwater management using residential greenspace, as well as the larger implications for decentralized stormwater management at city-wide scale.

Large-eddy simulation of pollutant dispersion from a ground-level area source over urban street canyons with irreversible chemical reactions

NASA Astrophysics Data System (ADS)

Du, T. Z.; Liu, C.-H.; Zhao, Y. B.

2014-10-01

In this study, the dispersion of chemically reactive pollutants is calculated by large-eddy simulation (LES) in a neutrally stratified urban canopy layer (UCL) over urban areas. As a pilot attempt, idealized street canyons of unity building-height-to-street-width (aspect) ratio are used. Nitric oxide (NO) is emitted from the ground surface of the first street canyon into the domain doped with ozone (O3). In the absence of ultraviolet radiation, this irreversible chemistry produces nitrogen dioxide (NO2), developing a reactive plume over the rough urban surface. A range of timescales of turbulence and chemistry are utilized to examine the mechanism of turbulent mixing and chemical reactions in the UCL. The Damköhler number (Da) and the reaction rate (r) are analyzed along the vertical direction on the plane normal to the prevailing flow at 10 m after the source. The maximum reaction rate peaks at an elevation where Damköhler number Da is equal or close to unity. Hence, comparable timescales of turbulence and reaction could enhance the chemical reactions in the plume.

Built Expansion and Global Climate Change Drive Projected Urban Heat: Relative Magnitudes, Interactions, and Mitigation

NASA Astrophysics Data System (ADS)

Krayenhoff, E. S.; Georgescu, M.; Moustaoui, M.

2016-12-01

Surface climates are projected to warm due to global climate change over the course of the 21st century, and demographic projections suggest urban areas in the United States will continue to expand and develop, with associated local climate outcomes. Interactions between these two drivers of urban heat have not been robustly quantified to date. Here, simulations with the Weather Research and Forecasting model (coupled to a Single-Layer Urban Canopy Model) are performed at 20 km resolution over the continental U.S. for two 10-year periods: contemporary (2000-2009) and end-of-century (2090-2099). Present and end of century urban land use are derived from the Environmental Protection Agency's Integrated Climate and Land-Use Scenarios. Modelled effects on urban climates are evaluated regionally. Sensitivity to climate projection (Community Climate System Model 4.0, RCP 4.5 vs. RCP 8.5) and associated urban development scenarios are assessed. Effects on near-surface urban air temperature of RCP8.5 climate change are greater than those attributable to the corresponding urban development in many regions. Interaction effects vary by region, and while of lesser magnitude, are not negligible. Moreover, urban development and its interactions with RCP8.5 climate change modify the distribution of convective precipitation over the eastern US. Interaction effects result from the different meteorological effects of urban areas under current and future climate. Finally, the potential for design implementations such as green roofs and high albedo roofs to offset the projected warming is considered. Impacts of these implementations on precipitation are also assessed.

Impacts of phenology on estimation of actual evapotranspiration with VegET model

NASA Astrophysics Data System (ADS)

Kovalskyy, V.; Henebry, G. M.

2009-12-01

The VegET model provides spatially explicit estimation of actual evapotranspiration (AET). Currently, it uses a climatology based on AVHRR NDVI image time series to modulate fluxes during growing seasons (Senay 2008). This step simplifies the model formulation, but it also introduces errors by ignoring the interannual variation in phenology. We report on a study to evaluate the effects of using an NDVI climatology in VegET rather than current season values. Using flux tower data from three sites across the US Corn Belt, we found that currently the model overestimates the duration of season. With the standard deviation of more than one week, the model results in an additional 50 to 70 mm of AET per season, which can account for about 10% of seasonal AET in drier western sites. The model showed only modest sensitivity to variation in growing season weather. This lack of sensitivity greatly decreased model accuracy during drought years: Pearson correlation coefficients between model estimates and observed values dropped from about 0.7 to 0.5, depending on vegetation type. We also evaluated an alternative approach to drive the canopy component of evapotranspiration, the Event Driven Phenology Model (EDPM). The parameterization of VegET with EDPM-simulated canopy dynamics improved the correlation by 0.1 or more and reduced the RMSE on daily AET estimates by 0.3 mm. By accounting for the progress of phenology during a particular growing season, the EDPM improves AET estimation over an NDVI climatology.

Beyond the climate envelope: using trait filtering models to predict biome boundaries from plant physiology.

NASA Astrophysics Data System (ADS)

Fisher, R.; Hoffmann, W. A.; Muszala, S.

2014-12-01

The introduction of second-generation dynamic vegetation models - which simulate the distribution of light resources between plant types along the vertical canopy profile, and therefore facilitate the representation of plant competition explicitly - is a large increase in the complexity and fidelity with which the terrestrial biosphere is abstracted into Earth System Models. In this new class of model, biome boundaries are predicted as the emergent properties of plant physiology, and are therefore sensitive to the high-dimensional parameterizations of plant functional traits. These new approaches offer the facility to quantitatively test ecophysiological hypotheses of plant distribution at large scales, a field which remains surprisingly under-developed. Here we describe experiments conducted with the Community Land Model Ecosystem Demography component, CLM(ED), in which we reduce the complexity of the problem by testing how individual plant functional trait changes to control the location of biome boundaries between functional types. Specifically, we investigate which physiological trade-offs determine the boundary between frequently burned savanna and forest biomes, and attempt to distinguish how each strategic life-history trade-off (carbon storage, bark investment, re-sprouting strategy) contributes towards the maintenance of sharp geographical gradients between fire adapted and typically inflammable closed canopy ecosystems. This study forms part of the planning for a model-inspired fire manipulation experiment at the cerrado-forest boundary in South-Eastern Brazil, and the results will be used to guide future data-collection and analysis strategies.

Simulation Studies of the Effect of Forest Spatial Structure on InSAR Signature

NASA Technical Reports Server (NTRS)

Sun, Guoqing; Liu, Dawei; Ranson, K. Jon; Koetz, Benjamin

2007-01-01

The height of scattering phase retrieved from InSAR data is considered being correlated with the tree height and the spatial structure of the forest stand. Though some researchers have used simple backscattering models to estimate tree height from the height of scattering center, the effect of forest spatial structure on InSAR data is not well understood yet. A three-dimensional coherent radar backscattering model for forest canopies based on realistic three-dimensional scene was used to investigate the effect in this paper. The realistic spatial structure of forest canopies was established either by field measurements (stem map) or through use of forest growth model. Field measurements or a forest growth model parameterized using local environmental parameters provides information of forest species composition and tree sizes in certain growth phases. A fractal tree model (L-system) was used to simulate individual 3- D tree structure of different ages or heights. Trees were positioned in a stand in certain patterns resulting in a 3-D medium of discrete scatterers. The radar coherent backscatter model took the 3-D forest scene as input and simulates the coherent radar backscattering signature. Interferometric SAR images of 3D scenes were simulated and heights of scattering phase centers were estimated from the simulated InSAR data. The effects of tree height, crown cover, crown depth, and the spatial distribution patterns of trees on the scattering phase center were analyzed. The results will be presented in the paper.

Pollutant Plume Dispersion over Hypothetical Urban Areas based on Wind Tunnel Measurements

NASA Astrophysics Data System (ADS)

Mo, Ziwei; Liu, Chun-Ho

2017-04-01

Gaussian plume model is commonly adopted for pollutant concentration prediction in the atmospheric boundary layer (ABL). However, it has a number of limitations being applied to pollutant dispersion over complex land-surface morphology. In this study, the friction factor (f), as a measure of aerodynamic resistance induced by rough surfaces in the engineering community, was proposed to parameterize the vertical dispersion coefficient (σz) in the Gaussian model. A series of wind tunnel experiments were carried out to verify the mathematical hypothesis and to characterize plume dispersion as a function of surface roughness as well. Hypothetical urban areas, which were assembled in the form of idealized street canyons of different aspect (building-height-to-street-width) ratios (AR = 1/2, 1/4, 1/8 and 1/12), were fabricated by aligning identical square aluminum bars at different separation apart in cross flows. Pollutant emitted from a ground-level line source into the turbulent boundary layer (TBL) was simulated using water vapour generated by ultrasonic atomizer. The humidity and the velocity (mean and fluctuating components) were measured, respectively, by humidity sensors and hot-wire anemometry (HWA) with X-wire probes in streamwise and vertical directions. Wind tunnel results showed that the pollutant concentration exhibits the conventional Gaussian distribution, suggesting the feasibility of using water vapour as a passive scalar in wind tunnel experiments. The friction factor increased with decreasing aspect ratios (widening the building separation). It was peaked at AR = 1/8 and decreased thereafter. Besides, a positive correlation between σz/xn (x is the distance from the pollutant source) and f1/4 (correlation coefficient r2 = 0.61) was observed, formulating the basic parameterization of plume dispersion over urban areas.

The interactions between soil-biosphere-atmosphere land surface model with a multi-energy balance (ISBA-MEB) option in SURFEXv8 - Part 1: Model description

NASA Astrophysics Data System (ADS)

Boone, Aaron; Samuelsson, Patrick; Gollvik, Stefan; Napoly, Adrien; Jarlan, Lionel; Brun, Eric; Decharme, Bertrand

2017-02-01

Land surface models (LSMs) are pushing towards improved realism owing to an increasing number of observations at the local scale, constantly improving satellite data sets and the associated methodologies to best exploit such data, improved computing resources, and in response to the user community. As a part of the trend in LSM development, there have been ongoing efforts to improve the representation of the land surface processes in the interactions between the soil-biosphere-atmosphere (ISBA) LSM within the EXternalized SURFace (SURFEX) model platform. The force-restore approach in ISBA has been replaced in recent years by multi-layer explicit physically based options for sub-surface heat transfer, soil hydrological processes, and the composite snowpack. The representation of vegetation processes in SURFEX has also become much more sophisticated in recent years, including photosynthesis and respiration and biochemical processes. It became clear that the conceptual limits of the composite soil-vegetation scheme within ISBA had been reached and there was a need to explicitly separate the canopy vegetation from the soil surface. In response to this issue, a collaboration began in 2008 between the high-resolution limited area model (HIRLAM) consortium and Météo-France with the intention to develop an explicit representation of the vegetation in ISBA under the SURFEX platform. A new parameterization has been developed called the ISBA multi-energy balance (MEB) in order to address these issues. ISBA-MEB consists in a fully implicit numerical coupling between a multi-layer physically based snowpack model, a variable-layer soil scheme, an explicit litter layer, a bulk vegetation scheme, and the atmosphere. It also includes a feature that permits a coupling transition of the snowpack from the canopy air to the free atmosphere. It shares many of the routines and physics parameterizations with the standard version of ISBA. This paper is the first of two parts; in part one, the ISBA-MEB model equations, numerical schemes, and theoretical background are presented. In part two (Napoly et al., 2016), which is a separate companion paper, a local scale evaluation of the new scheme is presented along with a detailed description of the new forest litter scheme.

Simulating damage for wind storms in the land surface model ORCHIDEE-CAN (revision 4262)

NASA Astrophysics Data System (ADS)

Chen, Yi-Ying; Gardiner, Barry; Pasztor, Ferenc; Blennow, Kristina; Ryder, James; Valade, Aude; Naudts, Kim; Otto, Juliane; McGrath, Matthew J.; Planque, Carole; Luyssaert, Sebastiaan

2018-03-01

Earth system models (ESMs) are currently the most advanced tools with which to study the interactions among humans, ecosystem productivity, and the climate. The inclusion of storm damage in ESMs has long been hampered by their big-leaf approach, which ignores the canopy structure information that is required for process-based wind-throw modelling. Recently the big-leaf assumptions in the large-scale land surface model ORCHIDEE-CAN were replaced by a three-dimensional description of the canopy structure. This opened the way to the integration of the processes from the small-scale wind damage risk model ForestGALES into ORCHIDEE-CAN. The integration of ForestGALES into ORCHIDEE-CAN required, however, developing numerically efficient solutions to deal with (1) landscape heterogeneity, i.e. account for newly established forest edges for the parameterization of gusts; (2) downscaling spatially and temporally aggregated wind fields to obtain more realistic wind speeds that would represents gusts; and (3) downscaling storm damage within the 2500 km2 pixels of ORCHIDEE-CAN. This new version of ORCHIDEE-CAN was parameterized over Sweden. Subsequently, the performance of the model was tested against data for historical storms in southern Sweden between 1951 and 2010 and south-western France in 2009. In years without big storms, here defined as a storm damaging less than 15 × 106 m3 of wood in Sweden, the model error is 1.62 × 106 m3, which is about 100 % of the observed damage. For years with big storms, such as Gudrun in 2005, the model error increased to 5.05 × 106 m3, which is between 10 and 50 % of the observed damage. When the same model parameters were used over France, the model reproduced a decrease in leaf area index and an increase in albedo, in accordance with SPOT-VGT and MODIS records following the passing of Cyclone Klaus in 2009. The current version of ORCHIDEE-CAN (revision 4262) is therefore expected to have the capability to capture the dynamics of forest structure due to storm disturbance on both regional and global scales, although the empirical parameters calculating gustiness from the gridded wind fields and storm damage from critical wind speeds may benefit from regional fitting.

Modeling the Warming Impact of Urban Land Expansion on Hot Weather Using the Weather Research and Forecasting Model: A Case Study of Beijing, China

NASA Astrophysics Data System (ADS)

Liu, Xiaojuan; Tian, Guangjin; Feng, Jinming; Ma, Bingran; Wang, Jun; Kong, Lingqiang

2018-06-01

The impacts of three periods of urban land expansion during 1990-2010 on near-surface air temperature in summer in Beijing were simulated in this study, and then the interrelation between heat waves and urban warming was assessed. We ran the sensitivity tests using the mesoscaleWeather Research and Forecasting model coupled with a single urban canopy model, as well as high-resolution land cover data. The warming area expanded approximately at the same scale as the urban land expansion. The average regional warming induced by urban expansion increased but the warming speed declined slightly during 2000-2010. The smallest warming occurred at noon and then increased gradually in the afternoon before peaking at around 2000 LST—the time of sunset. In the daytime, urban warming was primarily caused by the decrease in latent heat flux at the urban surface. Urbanization led to more ground heat flux during the day and then more release at night, which resulted in nocturnal warming. Urban warming at night was higher than that in the day, although the nighttime increment in sensible heat flux was smaller. This was because the shallower planetary boundary layer at night reduced the release efficiency of near-surface heat. The simulated results also suggested that heat waves or high temperature weather enhanced urban warming intensity at night. Heat waves caused more heat to be stored in the surface during the day, greater heat released at night, and thus higher nighttime warming. Our results demonstrate a positive feedback effect between urban warming and heat waves in urban areas.

Investigating Dry Deposition of Ozone to Vegetation

NASA Astrophysics Data System (ADS)

Silva, Sam J.; Heald, Colette L.

2018-01-01

Atmospheric ozone loss through dry deposition to vegetation is a critically important process for both air quality and ecosystem health. The majority of atmospheric chemistry models calculate dry deposition using a resistance-in-series parameterization by Wesely (1989), which is dependent on many environmental variables and lookup table values. The uncertainties contained within this parameterization have not been fully explored, ultimately challenging our ability to understand global scale biosphere-atmosphere interactions. In this work, we evaluate the GEOS-Chem model simulation of ozone dry deposition using a globally distributed suite of observations. We find that simulated daytime deposition velocities generally reproduce the magnitude of observations to within a factor of 1.4. When correctly accounting for differences in land class between the observations and model, these biases improve, most substantially over the grasses and shrubs land class. These biases do not impact the global ozone burden substantially; however, they do lead to local absolute changes of up to 4 ppbv and relative changes of 15% in summer surface concentrations. We use MERRA meteorology from 1979 to 2008 to assess that the interannual variability in simulated annual mean ozone dry deposition due to model input meteorology is small (generally less than 5% over vegetated surfaces). Sensitivity experiments indicate that the simulation is most sensitive to the stomatal and ground surface resistances, as well as leaf area index. To improve ozone dry deposition models, more measurements are necessary over rainforests and various crop types, alongside constraints on individual depositional pathways and other in-canopy ozone loss processes.

Modeling particle nucleation and growth over northern California during the 2010 CARES campaign

NASA Astrophysics Data System (ADS)

Lupascu, A.; Easter, R.; Zaveri, R.; Shrivastava, M.; Pekour, M.; Tomlinson, J.; Yang, Q.; Matsui, H.; Hodzic, A.; Zhang, Q.; Fast, J. D.

2015-07-01

Accurate representation of the aerosol lifecycle requires adequate modeling of the particle number concentration and size distribution in addition to their mass, which is often the focus of aerosol modeling studies. This paper compares particle number concentrations and size distributions as predicted by three empirical nucleation parameterizations in the Weather Research and Forecast coupled with chemistry (WRF-Chem) regional model using 20 discrete size bins ranging from 1 nm to 10 μm. Two of the parameterizations are based on H2SO4 while one is based on both H2SO4 and organic vapors. Budget diagnostic terms for transport, dry deposition, emissions, condensational growth, nucleation, and coagulation of aerosol particles have been added to the model and are used to analyze the differences in how the new particle formation parameterizations influence the evolving aerosol size distribution. The simulations are evaluated using measurements collected at surface sites and from a research aircraft during the Carbonaceous Aerosol and Radiative Effects Study (CARES) conducted in the vicinity of Sacramento, California. While all three parameterizations captured the temporal variation of the size distribution during observed nucleation events as well as the spatial variability in aerosol number, all overestimated by up to a factor of 2.5 the total particle number concentration for particle diameters greater than 10 nm. Using the budget diagnostic terms, we demonstrate that the combined H2SO4 and low-volatility organic vapors parameterization leads to a different diurnal variability of new particle formation and growth to larger sizes compared to the parameterizations based on only H2SO4. At the CARES urban ground site, peak nucleation rates were predicted to occur around 12:00 Pacific (local) standard time (PST) for the H2SO4 parameterizations, whereas the highest rates were predicted at 08:00 and 16:00 PST when low-volatility organic gases are included in the parameterization. This can be explained by higher anthropogenic emissions of organic vapors at these times as well as lower boundary layer heights that reduce vertical mixing. The higher nucleation rates in the H2SO4-organic parameterization at these times were largely offset by losses due to coagulation. Despite the different budget terms for ultrafine particles, the 10-40 nm diameter particle number concentrations from all three parameterizations increased from 10:00 to 14:00 PST and then decreased later in the afternoon, consistent with changes in the observed size and number distribution. Differences among the three simulations for the 40-100 nm particle diameter range are mostly associated with the timing of the peak total tendencies that shift the morning increase and afternoon decrease in particle number concentration by up to two hours. We found that newly formed particles could explain up to 20-30 % of predicted cloud condensation nuclei at 0.5 % supersaturation, depending on location and the specific nucleation parameterization. A sensitivity simulation using 12 discrete size bins ranging from 1 nm to 10 μm diameter gave a reasonable estimate of particle number and size distribution compared to the 20 size bin simulation, while reducing the associated computational cost by ∼ 36 %.

Incorporation of new particle formation and early growth treatments into WRF/Chem: Model improvement, evaluation, and impacts of anthropogenic aerosols over East Asia

NASA Astrophysics Data System (ADS)

Cai, Changjie; Zhang, Xin; Wang, Kai; Zhang, Yang; Wang, Litao; Zhang, Qiang; Duan, Fengkui; He, Kebin; Yu, Shao-Cai

2016-01-01

New particle formation (NPF) provides an important source of aerosol particles and cloud condensation nuclei, which may result in enhanced cloud droplet number concentration (CDNC) and cloud shortwave albedo. In this work, several nucleation parameterizations and one particle early growth parameterization are implemented into the online-coupled Weather Research and Forecasting model coupled with chemistry (WRF/Chem) to improve the model's capability in simulating NPF and early growth of ultrafine particles over East Asia. The default 8-bin over the size range of 39 nm-10 μm used in the Model for Simulating Aerosol Interactions and Chemistry aerosol module is expanded to the 12-bin over 1 nm-10 μm to explicitly track the formation and evolution of new particles. Although model biases remain in simulating H2SO4, condensation sink, growth rate, and formation rate, the evaluation of July 2008 simulation identifies a combination of three nucleation parameterizations (i.e., COMB) that can best represent the atmospheric nucleation processes in terms of both surface nucleation events and the resulting vertical distribution of ultrafine particle concentrations. COMB consists of a power law of Wang et al. (2011) based on activation theory for urban areas in planetary boundary layer (PBL), a power law of Boy et al. (2008) based on activation theory for non-urban areas in PBL, and the ion-mediated nucleation parameterization of YU10 for above PBL. The application and evaluation of the improved model with 12-bin and the COMB nucleation parameterization in East Asia during January, April, July, and October in 2001 show that the model has an overall reasonably good skill in reproducing most observed meteorological variables and surface and column chemical concentrations. Relatively large biases in simulated precipitation and wind speeds are due to inaccurate surface roughness and limitations in model treatments of cloud formation and aerosol-cloud-precipitation interactions. Large biases in the simulated surface concentrations of PM10, NOx, CO, SO2, and VOCs at some sites are due in part to possible underestimations of emissions and in part to inaccurate meteorological predictions. The simulations of 2001 show that anthropogenic aerosols can increase aerosol optical depth by 64.0-228.3%, CDNC by 40.2-76.4%, and cloud optical thickness by 14.3-25.3%; they can reduce surface net shortwave radiation by up to 42.5-52.8 W m-2, 2-m temperature by up to 0.34-0.83 °C, and PBL height by up to 76.8-125.9 m. Such effects are more significant than those previously reported for the U.S. and Europe.