Influence of an urban canopy model and PBL schemes on vertical mixing for air quality modeling over Greater Paris

NASA Astrophysics Data System (ADS)

Kim, Youngseob; Sartelet, Karine; Raut, Jean-Christophe; Chazette, Patrick

2015-04-01

Impacts of meteorological modeling in the planetary boundary layer (PBL) and urban canopy model (UCM) on the vertical mixing of pollutants are studied. Concentrations of gaseous chemical species, including ozone (O3) and nitrogen dioxide (NO2), and particulate matter over Paris and the near suburbs are simulated using the 3-dimensional chemistry-transport model Polair3D of the Polyphemus platform. Simulated concentrations of O3, NO2 and PM10/PM2.5 (particulate matter of aerodynamic diameter lower than 10 μm/2.5 μm, respectively) are first evaluated using ground measurements. Higher surface concentrations are obtained for PM10, PM2.5 and NO2 with the MYNN PBL scheme than the YSU PBL scheme because of lower PBL heights in the MYNN scheme. Differences between simulations using different PBL schemes are lower than differences between simulations with and without the UCM and the Corine land-use over urban areas. Regarding the root mean square error, the simulations using the UCM and the Corine land-use tend to perform better than the simulations without it. At urban stations, the PM10 and PM2.5 concentrations are over-estimated and the over-estimation is reduced using the UCM and the Corine land-use. The ability of the model to reproduce vertical mixing is evaluated using NO2 measurement data at the upper air observation station of the Eiffel Tower, and measurement data at a ground station near the Eiffel Tower. Although NO2 is under-estimated in all simulations, vertical mixing is greatly improved when using the UCM and the Corine land-use. Comparisons of the modeled PM10 vertical distributions to distributions deduced from surface and mobile lidar measurements are performed. The use of the UCM and the Corine land-use is crucial to accurately model PM10 concentrations during nighttime in the center of Paris. In the nocturnal stable boundary layer, PM10 is relatively well modeled, although it is over-estimated on 24 May and under-estimated on 25 May. However, PM10 is under-estimated on both days in the residual layer, and over-estimated on both days over the residual layer. The under-estimations in the residual layer are partly due to difficulties to estimate the PBL height, to an over-estimation of vertical mixing during nighttime at high altitudes and to uncertainties in PM10 emissions. The PBL schemes and the UCM influence the PM vertical distributions not only because they influence vertical mixing (PBL height and eddy-diffusion coefficient), but also horizontal wind fields and humidity. However, for the UCM, it is the influence on vertical mixing that impacts the most the PM10 vertical distribution below 1.5 km.

Contribution and loading estimation of organochlorine pesticides from rain and canopy throughfall to runoff in an urban environment.

PubMed

Zhang, Wei; Ye, Youbin; Tong, Yindong; Ou, Langbo; Hu, Dan; Wang, Xuejun

2011-01-30

Concentrations of OCPs in rain, canopy throughfall, and runoff water were measured in the Beijing metropolitan area during the rainy seasons from 2006 to 2007. This study was conducted to calculate the fluxes of OCPs in rain and canopy throughfall, as well as their contributions to runoff. At urban sites, the contribution of HCB and ΣHCHs from rainfall accounted for approximately 50% of the mass in runoff. At the site with significant coverage of landscaping trees, the HCB, ΣHCHs, and ΣDDTs from the net canopy throughfall accounted for approximately 10% of the mass in the runoff. Based on the data obtained in this study, loadings of OCPs (in μg) in rain, net canopy throughfall, and runoff water were calculated. The input of OCPs from rain and canopy throughfall water accounted for a significant portion of urban runoff. In cities undergoing rapid urban sprawl, monitoring and control of the transport of OCPs in urban runoff are essential for effective control of environmental hazards in surface water bodies. Copyright © 2010 Elsevier B.V. All rights reserved.

Applications of urban tree canopy assessment and prioritization tools: supporting collaborative decision making to achieve urban sustainability goals

Treesearch

Dexter H. Locke; J. Morgan Grove; Michael Galvin; Jarlath P.M. ONeil-Dunne; Charles Murphy

2013-01-01

Urban Tree Canopy (UTC) Prioritizations can be both a set of geographic analysis tools and a planning process for collaborative decision-making. In this paper, we describe how UTC Prioritizations can be used as a planning process to provide decision support to multiple government agencies, civic groups and private businesses to aid in reaching a canopy target. Linkages...

Impact of urban canopy models and external parameters on the modelled urban energy balance in a tropical city

NASA Astrophysics Data System (ADS)

Demuzere, Matthias; Harshan, Suraj; Järvi, Leena; Roth, Matthias; Betham Grimmond, Christine Susan; Masson, Valéry; Oleson, Keith; Velasco Saldana, Hector Erik; Wouters, Hendrik

2017-04-01

This paper provides the first comparative evaluation of four urban land surface models for a tropical residential neighbourhood in Singapore. The simulations are performed offline, for an 11-month period, using the bulk scheme TERRA_URB and three models of intermediate complexity (CLM, SURFEX and SUEWS). In addition, information from three different parameter lists are added to quantify the impact (interaction) of (between) external parameter settings and model formulations on the modelled urban energy balance components. Overall, the models' performance using the reference parameters aligns well with previous findings for mid- and high-latitude sites against (for) which the models are generally optimised (evaluated). The various combinations of models and different parameter values suggest that error statistics tend to be more dominated by the choice of the latter than the choice of model. Stratifying the observation period into dry / wet periods and hours since selected precipitation events reveals that the models' skill generally deteriorates during dry periods while e.g. CLM/SURFEX has a positive bias in the latent heat flux directly after a precipitation event. It is shown that the latter is due to simple representation of water intercepted on the impervious surfaces. In addition, the positive bias in modelled outgoing longwave radiation is attributed to neglecting the interactions between water vapor and radiation between the surface and the tower sensor. These findings suggest that future developments in urban climate research should continue the integration of more physically-based processes in urban canopy models, ensure the consistency between the observed and modelled atmospheric properties and focus on the correct representation of urban morphology and thermal and radiative characteristics.

INITIAL STUDY OF HPAC MODELED DISPERSION DRIVEN BY MM5 WITH AND WITHOUT URBAN CANOPY PARAMETERIZATIONS

EPA Science Inventory

Improving the accuracy and capability of transport and dispersion models in urban areas is essential for current and future urban applications. These models must reflect more realistically the presence and details of urban canopy features. Such features markedly influence the flo...

Difficulties with estimating city-wide urban forest cover change from national, remotely-sensed tree canopy maps

Treesearch

Jeffrey T. Walton

2008-01-01

Two datasets of percent urban tree canopy cover were compared. The first dataset was based on a 1991 AVHRR forest density map. The second was the US Geological Survey's National Land Cover Database (NLCD) 2001 sub-pixel tree canopy. A comparison of these two tree canopy layers was conducted in 36 census designated places of western New York State. Reference data...

Mean and turbulent flow statistics in a trellised agricultural canopy

USDA-ARS?s Scientific Manuscript database

The architecture of a trellised agricultural canopy presents many similarities to homogeneous plant canopies, windbreaks, and urban canopies including street canyons. Compared to these other canopies, trellised canopies (e.g. vineyard) present an interesting, complex, two-dimensional environment tha...

IMPLEMENTATION OF AN URBAN CANOPY PARAMETERIZATION IN MM5

EPA Science Inventory

The Pennsylvania State University/National Center for Atmospheric Research Mesoscale Model (MM5) (Grell et al. 1994) has been modified to include an urban canopy parameterization (UCP) for fine-scale urban simulations (~1-km horizontal grid spacing). The UCP accounts for drag ...

IMPLEMENTATION OF AN URBAN CANOPY PARAMETERIZATION FOR FINE-SCALE SIMULATIONS

EPA Science Inventory

The Pennsylvania State University/National Center for Atmospheric Research Mesoscale Model (MM5) (Grell et al. 1994) has been modified to include an urban canopy parameterization (UCP) for fine-scale urban simulations ( 1 - km horizontal grid spacing ). The UCP accounts for dr...

Watershed Land Use and Seasonal Variation Constrain the ...

EPA Pesticide Factsheets

While watershed and local scale controls on stream metabolism have been independently investigated, little is known about how controls exerted at these different scales interact to determine stream metabolic rates, or how these interactions vary across seasons. To address this knowledge gap, we measured ecosystem metabolism in four urban and four reference streams in northern Kentucky, USA, with paired closed and open riparian canopies, during each of the four seasons of the year. Gross primary production (GPP), ecosystem respiration (ER), and net ecosystem production (NEP) were all best predicted by models with season as a main effect, but interactions between season, canopy and watershed varied for each response. Urban streams exhibited higher GPP during most seasons, likely due to elevated nutrient loads. Open canopy reaches in both urban and forested streams supported higher rates of GPP than the closed canopy reaches during the summer and fall when the overhead vegetation shaded the closed reaches. Surprisingly, the effect of canopy cover on GPP was similar among urban and forested streams. The combination of watershed and local-scale controls resulted in urban streams that alternated between net heterotrophy (NEP 0) between seasons with and without dense canopy cover. This finding has management relevance because net production can lead to accumulation of algal biomass and associated issues like dissolved oxygen sags at night. Our study reinforces

Canopy reflectance, photosynthesis, and transpiration. III - A reanalysis using improved leaf models and a new canopy integration scheme

NASA Technical Reports Server (NTRS)

Sellers, P. J.; Berry, J. A.; Collatz, G. J.; Field, C. B.; Hall, F. G.

1992-01-01

The theoretical analyses of Sellers (1985, 1987), which linked canopy spectral reflectance properties to (unstressed) photosynthetic rates and conductances, are critically reviewed and significant shortcomings are identified. These are addressed in this article principally through the incorporation of a more sophisticated and realistic treatment of leaf physiological processes within a new canopy integration scheme. The results indicate that area-averaged spectral vegetation indices, as obtained from coarse resolution satellite sensors, may give good estimates of the area-integrals of photosynthesis and conductance even for spatially heterogenous (though physiologically uniform) vegetation covers.

Incorporating Plant Phenology Dynamics in a Biophysical Canopy Model

NASA Technical Reports Server (NTRS)

Barata, Raquel A.; Drewry, Darren

2012-01-01

The Multi-Layer Canopy Model (MLCan) is a vegetation model created to capture plant responses to environmental change. Themodel vertically resolves carbon uptake, water vapor and energy exchange at each canopy level by coupling photosynthesis, stomatal conductance and leaf energy balance. The model is forced by incoming shortwave and longwave radiation, as well as near-surface meteorological conditions. The original formulation of MLCan utilized canopy structural traits derived from observations. This project aims to incorporate a plant phenology scheme within MLCan allowing these structural traits to vary dynamically. In the plant phenology scheme implemented here, plant growth is dependent on environmental conditions such as air temperature and soil moisture. The scheme includes functionality that models plant germination, growth, and senescence. These growth stages dictate the variation in six different vegetative carbon pools: storage, leaves, stem, coarse roots, fine roots, and reproductive. The magnitudes of these carbon pools determine land surface parameters such as leaf area index, canopy height, rooting depth and root water uptake capacity. Coupling this phenology scheme with MLCan allows for a more flexible representation of the structure and function of vegetation as it responds to changing environmental conditions.

Effects of urban tree canopy loss on land surface temperature magnitude and timing

Treesearch

Arthur Elmes; John Rogan; Christopher Williams; Samuel Ratick; David Nowak; Deborah Martin

2017-01-01

Urban Tree Canopy (UTC) plays an important role in moderating the Surface Urban Heat Island (SUHI) effect, which poses threats to human health due to substantially increased temperatures relative to rural areas. UTC coverage is associated with reduced urban temperatures, and therefore benefits both human health and reducing energy use in cities. Measurement of this...

Tree canopy change and neighborhood stability: A comparative analysis of Washington, D.C. and Baltimore, MD

Treesearch

Wen-Ching Chuang; Christopher G. Boone; Dexter H. Locke; J. Morgan Grove; Ali Whitmer; Geoffrey Buckley; Sainan Zhang

2017-01-01

Trees provide important health, ecosystem, and aesthetic services in urban areas, but they are unevenly distributed. Some neighborhoods have abundant tree canopy and others nearly none. We analyzed how neighborhood characteristics and changes in income over time related to the distribution of urban tree canopy in Washington, D.C. and Baltimore, MD. We used stepwise...

What's scale got to do with it? Models for urban tree canopy

Treesearch

Dexter H. Locke; Shawn M. Landry; Morgan Grove; Rinku Roy Chowdhury

2016-01-01

The uneven provisioning of ecosystem services has important policy implications; yet the spatial heterogeneity of tree canopy remains understudied. Private residential lands are important to the future of Philadelphia’s urban forest because a majority of the existing and possible tree canopy is located on residential land uses. This article examines the spatial...

Case study: Rainfall partitioning across a natural-to-urban forest gradient during an extreme rain event

NASA Astrophysics Data System (ADS)

Akin, B. H.; Van Stan, J. T., II; Cote, J. F.; Jarvis, M. T.; Underwood, J.; Friesen, J.; Hildebrandt, A.; Maldonado, G.

2017-12-01

Trees' partitioning of rainfall is an important first process along the rainfall-to-runoff pathway that has economically significant influences on urban stormwater management. However, important knowledge gaps exist regarding (1) its role during extreme storms and (2) how this role changes as forest structure is altered by urbanization. Little research has been conducted on canopy rainfall partitioning during large, intense storms, likely because canopy water storage is rapidly overwhelmed (i.e., 1-3 mm) by short duration events exceeding, for example, 80 mm of rainfall. However, canopy structure controls more than just storage; it also affects the time for rain to drain to the surface (becoming throughfall) and the micrometeorological conditions that drive wet canopy evaporation. In fact, observations from an example extreme ( 100 mm with maximum 5-minute intensities exceeding 55 mm/h) storm across a urban-to-natural gradient in pine forests in southeast Georgia (USA), show that storm intensities were differentially dampened by 33% (tree row), 28% (forest fragment), and 17% (natural forests). In addition, maximum wet canopy evaporation rates were higher for the exposed tree row (0.18 mm/h) than for the partially-enclosed fragment canopy (0.14 mm/h) and the closed canopy natural forest site (0.11). This resulted in interception percentages decreasing from urban-to-natural stand structures (25% to 16%). A synoptic analysis of the extreme storm in this case study also shows that the mesoscale meteorological conditions that developed the heavy rainfall is expected to occur more often with projected climate changes.

Simulation of Surface Energy Fluxes and Snow Interception Using a Higher Order Closure Multi-Layer Soil-Vegetation-Atmospheric Model: The Effect of Canopy Shape and Structure

NASA Astrophysics Data System (ADS)

McGowan, L. E.; Dahlke, H. E.; Paw U, K. T.

2015-12-01

Snow cover is a critical driver of the Earth's surface energy budget, climate change, and water resources. Variations in snow cover not only affect the energy budget of the land surface but also represent a major water supply source. In California, US estimates of snow depth, extent, and melt in the Sierra Nevada are critical to estimating the amount of water available for both California agriculture and urban users. However, accurate estimates of snow cover and snow melt processes in forested area still remain a challenge. Canopy structure influences the vertical and spatiotemporal distribution of snow, and therefore ultimately determines the degree and extent by which snow alters both the surface energy balance and water availability in forested regions. In this study we use the Advanced Canopy-Atmosphere-Soil algorithm (ACASA), a multi-layer soil-vegetation-atmosphere numerical model, to simulate the effect of different snow-covered canopy structures on the energy budget, and temperature and other scalar profiles within different forest types in the Sierra Nevada, California. ACASA incorporates a higher order turbulence closure scheme which allows the detailed simulation of turbulent fluxes of heat and water vapor as well as the CO2 exchange of several layers within the canopy. As such ACASA can capture the counter gradient fluxes within canopies that may occur frequently, but are typically unaccounted for, in most snow hydrology models. Six different canopy types were modeled ranging from coniferous forests (e.g. most biomass near the ground) to top-heavy (e.g. most biomass near the top of the crown) deciduous forests to multi-layered forest canopies (e.g. mixture of young and mature trees). Preliminary results indicate that the canopy shape and structure associated with different canopy types fundamentally influence the vertical scalar profiles (including those of temperature, moisture, and wind speed) in the canopy and thus alter the interception and snow melt dynamics in forested land surfaces. The turbulent transport dynamics, including counter-gradient fluxes, and radiation features including land surface albedo, are discussed in the context of the snow energy balance.

Comparative assessment of methods for estimating tree canopy cover across a rural-to-urban gradient in the mid-Atlantic region of the USA

Treesearch

Rachel Riemann; Greg C. Liknes; Jarlath O' Neil-Dunne; Chris Toney; Tonya Lister

2016-01-01

Tree canopy cover significantly affects human and wildlife habitats, local hydrology, carbon cycles, fire behavior, and ecosystem services of all types. In addition, changes in tree canopy cover are both indicators and consequences of a wide variety of disturbances from urban development to climate change. There is growing demand for this information nationwide and...

Mapping Urban Tree Canopy Cover Using Fused Airborne LIDAR and Satellite Imagery Data

NASA Astrophysics Data System (ADS)

Parmehr, Ebadat G.; Amati, Marco; Fraser, Clive S.

2016-06-01

Urban green spaces, particularly urban trees, play a key role in enhancing the liveability of cities. The availability of accurate and up-to-date maps of tree canopy cover is important for sustainable development of urban green spaces. LiDAR point clouds are widely used for the mapping of buildings and trees, and several LiDAR point cloud classification techniques have been proposed for automatic mapping. However, the effectiveness of point cloud classification techniques for automated tree extraction from LiDAR data can be impacted to the point of failure by the complexity of tree canopy shapes in urban areas. Multispectral imagery, which provides complementary information to LiDAR data, can improve point cloud classification quality. This paper proposes a reliable method for the extraction of tree canopy cover from fused LiDAR point cloud and multispectral satellite imagery data. The proposed method initially associates each LiDAR point with spectral information from the co-registered satellite imagery data. It calculates the normalised difference vegetation index (NDVI) value for each LiDAR point and corrects tree points which have been misclassified as buildings. Then, region growing of tree points, taking the NDVI value into account, is applied. Finally, the LiDAR points classified as tree points are utilised to generate a canopy cover map. The performance of the proposed tree canopy cover mapping method is experimentally evaluated on a data set of airborne LiDAR and WorldView 2 imagery covering a suburb in Melbourne, Australia.

Building capacity for providing canopy cover and canopy height at FIA plot locations using high-resolution imagery and leaf-off LiDAR

Treesearch

Rachel Riemann; Jarlath O' Neil-Dunne; Greg C. Liknes

2012-01-01

Tree canopy cover and canopy height information are essential for estimating volume, biomass, and carbon; defining forest cover; and characterizing wildlife habitat. The amount of tree canopy cover also influences water quality and quantity in both rural and urban settings. Tree canopy cover and canopy height are currently collected at FIA plots either in the field or...

Monitoring urban tree cover using object-based image analysis and public domain remotely sensed data

Treesearch

L. Monika Moskal; Diane M. Styers; Meghan Halabisky

2011-01-01

Urban forest ecosystems provide a range of social and ecological services, but due to the heterogeneity of these canopies their spatial extent is difficult to quantify and monitor. Traditional per-pixel classification methods have been used to map urban canopies, however, such techniques are not generally appropriate for assessing these highly variable landscapes....

Quality and sensitivity of high-resolution numerical simulation of urban heat islands

NASA Astrophysics Data System (ADS)

Li, Dan; Bou-Zeid, Elie

2014-05-01

High-resolution numerical simulations of the urban heat island (UHI) effect with the widely-used Weather Research and Forecasting (WRF) model are assessed. Both the sensitivity of the results to the simulation setup, and the quality of the simulated fields as representations of the real world, are investigated. Results indicate that the WRF-simulated surface temperatures are more sensitive to the planetary boundary layer (PBL) scheme choice during nighttime, and more sensitive to the surface thermal roughness length parameterization during daytime. The urban surface temperatures simulated by WRF are also highly sensitive to the urban canopy model (UCM) used. The implementation in this study of an improved UCM (the Princeton UCM or PUCM) that allows the simulation of heterogeneous urban facets and of key hydrological processes, together with the so-called CZ09 parameterization for the thermal roughness length, significantly reduce the bias (<1.5 °C) in the surface temperature fields as compared to satellite observations during daytime. The boundary layer potential temperature profiles are captured by WRF reasonable well at both urban and rural sites; the biases in these profiles relative to aircraft-mounted senor measurements are on the order of 1.5 °C. Changing UCMs and PBL schemes does not alter the performance of WRF in reproducing bulk boundary layer temperature profiles significantly. The results illustrate the wide range of urban environmental conditions that various configurations of WRF can produce, and the significant biases that should be assessed before inferences are made based on WRF outputs. The optimal set-up of WRF-PUCM developed in this paper also paves the way for a confident exploration of the city-scale impacts of UHI mitigation strategies in the companion paper (Li et al 2014).

Characteristics and transport of organochlorine pesticides in urban environment: air, dust, rain, canopy throughfall, and runoff.

PubMed

Zhang, Wei; Ye, Youbin; Hu, Dan; Ou, Langbo; Wang, Xuejun

2010-11-01

Characteristics and transport of organochlorine pesticides (OCPs) in urban multiple environments, including air, dust, rain, canopy throughfall, and runoff water, are explored in this study. Hexachlorocyclohexanes (HCHs) dominated in both air and rain water, and dichlorodiphenyltrichloroethane (DDT) related substances showed a higher affinity to dust. Relatively high concentrations of DDT and dichlorodiphenyldichloroethylene (DDE) in air, rain and dust imply that technical DDT in the environment has been degrading, and there may be unknown local or regional emission sources that contain DDTs in the study area. Source identification showed that DDTs in Beijing urban environments with a fresh signature may originate from the atmospheric transport from remote areas. The ratio of α-/γ-HCH in dust, rain, canopy throughfall and runoff were close to 1, indicating the possible use of lindane. OCPs in runoff were transported from various sources including rain, dust, and canopy throughfall. In runoff, DDTs and hexachlorobenzene (HCB) were mainly transported from dust, and HCHs were mainly from rain and canopy throughfall.

Intra-Urban Variability in Elemental Carbon Deposition to Tree Canopies

NASA Astrophysics Data System (ADS)

Barrett, T. E.; Ponette-González, A.; Rindy, J. E.; Sheesley, R. J.

2017-12-01

Urban areas cover <1% of the earth's land surface, yet they represent globally significant sources of atmospheric elemental carbon (EC). A product of incomplete fossil fuel, biofuel, and biomass combustion, EC is a powerful climate-forcing agent and a significant component of fine particulate matter in urban atmospheres. Thus, understanding the factors that govern EC removal in urban areas could help mitigate climate change, while improving air quality for urban residents. EC particles can be removed from the atmosphere in precipitation (wet and fog deposition) or they can settle directly onto receptor surfaces (dry deposition). Only limited measurements indicate that EC deposition is higher in urban than in rural and remote regions. However, EC deposition likely exhibits considerable intra-urban variability, with tree canopies serving as potentially important sinks for EC on the cityscape. The goal of this research is to quantify spatial variability in total (wet + dry) EC deposition to urban tree canopies in the Dallas-Fort Worth Metroplex. Using a stratified non-random sampling design, 41 oak trees (22 post oak (Quercus stellata) and 19 live oak (Quercus virginiana)) were selected near (<100 m) and far from roads (>100 m) for measurements of throughfall (water that falls from the canopy to the forest floor). Additionally, 16 bulk rainfall samplers were deployed in grassy areas with no canopy cover. Results from one rain event indicate a volume weighted mean concentration of 83 µg EC L-1 in post oak throughfall, 36 µg EC L-1 in live oak throughfall, and 4 µg EC L-1 in bulk rainfall. Total EC deposition to oak tree canopies was 2.0 ± 2.1 (SD) mg m-2 for post oak and 0.7 ± 0.3 mg m-2 for live oak. Bulk rainfall deposition was 0.08 ± 0.1 mg m-2. Our preliminary findings show that trees are effective urban air filters, removing 9-25 times more EC from the atmosphere than rainwater alone. Resolving surface controls on atmospheric EC removal is key to developing and assessing near-term climate and air quality mitigation strategies.

Growing Canopy on a College Campus: Understanding Urban Forest Change through Archival Records and Aerial Photography.

PubMed

Roman, Lara A; Fristensky, Jason P; Eisenman, Theodore S; Greenfield, Eric J; Lundgren, Robert E; Cerwinka, Chloe E; Hewitt, David A; Welsh, Caitlin C

2017-12-01

Many municipalities are setting ambitious tree canopy cover goals to increase the extent of their urban forests. A historical perspective on urban forest development can help cities strategize how to establish and achieve appropriate tree cover targets. To understand how long-term urban forest change occurs, we examined the history of trees on an urban college campus: the University of Pennsylvania in Philadelphia, PA. Using a mixed methods approach, including qualitative assessments of archival records (1870-2017), complemented by quantitative analysis of tree cover from aerial imagery (1970-2012), our analysis revealed drastic canopy cover increase in the late 20th and early 21st centuries along with the principle mechanisms of that change. We organized the historical narrative into periods reflecting campus planting actions and management approaches; these periods are also connected to broader urban greening and city planning movements, such as City Beautiful and urban sustainability. University faculty in botany, landscape architecture, and urban design contributed to the design of campus green spaces, developed comprehensive landscape plans, and advocated for campus trees. A 1977 Landscape Development Plan was particularly influential, setting forth design principles and planting recommendations that enabled the dramatic canopy cover gains we observed, and continue to guide landscape management today. Our results indicate that increasing urban tree cover requires generational time scales and systematic management coupled with a clear urban design vision and long-term commitments. With the campus as a microcosm of broader trends in urban forest development, we conclude with a discussion of implications for municipal tree cover planning.

The effect of urban growth on landscape-scale restoration for a fire-dependent songbird

USGS Publications Warehouse

Pickens, Bradley A.; Marcus, Jeffrey F.; Carpenter, John P.; Anderson, Scott; Taillie, Paul J.; Collazo, Jaime A.

2017-01-01

A landscape-scale perspective on restoration ecology has been advocated, but few studies have informed restoration with landscape metrics or addressed broad-scale threats. Threats such as urban growth may affect restoration effectiveness in a landscape context. Here, we studied longleaf pine savanna in the rapidly urbanizing southeastern United States where a habitat-specialist bird, Bachman's sparrow (Peucaea aestivalis), is closely associated with savanna vegetation structure and frequent fire. Our objectives were to construct a species distribution model for Bachman's sparrow, determine the relationship between fire and urbanization, quantify the urban growth effect (2010–2090), identify potential restoration areas, and determine the interaction between restoration potential and urban growth by 2050. Number of patches, patch size, and isolation metrics were used to evaluate scenarios. The species distribution model was 88% accurate and emphasized multiscale canopy cover characteristics, fire, and percent habitat. Fires were less common <600 m from urban areas, and this fire suppression effect exacerbated urban growth effects. For restoration scenarios, canopy cover reduction by 30% resulted in nearly double the amount of habitat compared to the prescribed fire scenario; canopy cover reduction resulted in larger patch sizes and less patch isolation compared to current conditions. The effect of urban growth on restoration scenarios was unequal. Seventy-four percent of restoration areas from the prescribed fire scenario overlapped with projected urban growth, whereas the canopy cover reduction scenario only overlapped by 9%. We emphasize the benefits of simultaneously considering the effects of urban growth and landscape-scale restoration potential to promote a landscape with greater patch sizes and less isolation.

Growing Canopy on a College Campus: Understanding Urban Forest Change through Archival Records and Aerial Photography

NASA Astrophysics Data System (ADS)

Roman, Lara A.; Fristensky, Jason P.; Eisenman, Theodore S.; Greenfield, Eric J.; Lundgren, Robert E.; Cerwinka, Chloe E.; Hewitt, David A.; Welsh, Caitlin C.

2017-12-01

Many municipalities are setting ambitious tree canopy cover goals to increase the extent of their urban forests. A historical perspective on urban forest development can help cities strategize how to establish and achieve appropriate tree cover targets. To understand how long-term urban forest change occurs, we examined the history of trees on an urban college campus: the University of Pennsylvania in Philadelphia, PA. Using a mixed methods approach, including qualitative assessments of archival records (1870-2017), complemented by quantitative analysis of tree cover from aerial imagery (1970-2012), our analysis revealed drastic canopy cover increase in the late 20th and early 21st centuries along with the principle mechanisms of that change. We organized the historical narrative into periods reflecting campus planting actions and management approaches; these periods are also connected to broader urban greening and city planning movements, such as City Beautiful and urban sustainability. University faculty in botany, landscape architecture, and urban design contributed to the design of campus green spaces, developed comprehensive landscape plans, and advocated for campus trees. A 1977 Landscape Development Plan was particularly influential, setting forth design principles and planting recommendations that enabled the dramatic canopy cover gains we observed, and continue to guide landscape management today. Our results indicate that increasing urban tree cover requires generational time scales and systematic management coupled with a clear urban design vision and long-term commitments. With the campus as a microcosm of broader trends in urban forest development, we conclude with a discussion of implications for municipal tree cover planning.

ADVANCED URBANIZED METEOROLOGICAL MODELING AND AIR QUALITY SIMULATIONS WITH CMAQ AT NEIGHBORHOOD SCALES

EPA Science Inventory

We present results from a study testing the new boundary layer parameterization method, the canopy drag approach (DA) which is designed to explicitly simulate the effects of buildings, street and tree canopies on the dynamic, thermodynamic structure and dispersion fields in urban...

Benefits of explicit urban parameterization in regional climate modeling to study climate and city interactions

NASA Astrophysics Data System (ADS)

Daniel, M.; Lemonsu, Aude; Déqué, M.; Somot, S.; Alias, A.; Masson, V.

2018-06-01

Most climate models do not explicitly model urban areas and at best describe them as rock covers. Nonetheless, the very high resolutions reached now by the regional climate models may justify and require a more realistic parameterization of surface exchanges between urban canopy and atmosphere. To quantify the potential impact of urbanization on the regional climate, and evaluate the benefits of a detailed urban canopy model compared with a simpler approach, a sensitivity study was carried out over France at a 12-km horizontal resolution with the ALADIN-Climate regional model for 1980-2009 time period. Different descriptions of land use and urban modeling were compared, corresponding to an explicit modeling of cities with the urban canopy model TEB, a conventional and simpler approach representing urban areas as rocks, and a vegetated experiment for which cities are replaced by natural covers. A general evaluation of ALADIN-Climate was first done, that showed an overestimation of the incoming solar radiation but satisfying results in terms of precipitation and near-surface temperatures. The sensitivity analysis then highlighted that urban areas had a significant impact on modeled near-surface temperature. A further analysis on a few large French cities indicated that over the 30 years of simulation they all induced a warming effect both at daytime and nighttime with values up to + 1.5 °C for the city of Paris. The urban model also led to a regional warming extending beyond the urban areas boundaries. Finally, the comparison to temperature observations available for Paris area highlighted that the detailed urban canopy model improved the modeling of the urban heat island compared with a simpler approach.

Quantifying interception associated with new urban vegetation canopies

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2013-12-01

Interception of precipitation by vegetation canopies has long been recognized as an important component of the hydrologic cycle, though most research has been in closed or sparse canopy forests. Much less work has been published on interception by urban vegetation, and especially associated with the low growing shrubs commonly installed in green infrastructure program. To inform urban watershed model with vegetation-specific interception data, a field experiment was designed to directly measure canopy throughfall associated with two shrub species commonly included in urban greening programs. Data was collected at a high (e.g. five second) sampling frequency. A non-parametric Kruskal-Wallis test performed on data collected between August and October of 2012 demonstrated statistically significant (p= 0.0011) differences in recorded throughfall between two species (94% for Itea virginica, 86% for Cornus sericea). Additionally, the results suggested that the relationship of throughfall to rainfall intensity varied by species. For Itea, the ratio of throughfall to precipitation intensity was close to 1:1. However, for Cornus, the throughfall rate was on average slower (or 0.85 of the precipitation intensity). An improved and expanded set-up installed in 2013 added two additional species (Prunus laurocerasus and Hydrangea quercifolia). The 2013 results confirm interspecies differences in both throughfall amount, and in the relationship of throughfall rate to precipitation intensity. The results are discussed with respect to droplet splashing and enhanced evaporation within the canopy. Both years' findings suggest that the quantity of water intercepted by vegetation canopies exceeds the canopy storage capacity, as assumed in many conventional hydrologic models.

The relationship between tree canopy and crime rates across an urban-rural gradient in the greater Baltimore region

Treesearch

Austin Troy; J. Morgan Grove; Jarlath O' Neill-Dunne

2012-01-01

The extent to which urban tree cover influences crime is in debate in the literature. This research took advantage of geocoded crime point data and high resolution tree canopy data to address this question in Baltimore City and County, MD, an area that includes a significant urban-rural gradient. Using ordinary least squares and spatially adjusted regression and...

Implication of Intrastorm Rainfall-Canopy Interaction on Interception Performance of Broadleaf Evergreen Shrubs in Urban Setting

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2014-12-01

Because of its ability to intercept a portion of rainfall, vegetated canopy has a significant influence on the urban hydrological cycle. In turn, urban watersheds, characterized by large impervious areas, have an enormous and often adverse impact on receiving waters. However, most historical interception research has been dedicated to forest canopies. The goal of our research was to quantify rainfall partitioning by isolated evergreen canopies in an urban setting. Two years of the field experiment involved three exemplars of Cherry Laurel (Prunus laurocerasus'Otto Luyken'.) Each plant had ten rain gauges to measure throughfall with a five second sampling frequency. A number of preventive techniques were introduced to minimize the gauges' errors (e.g., splash-in, splash-out and excessive wetting.) Leaf area index was measured manually. We estimated the canopy storage capacity to be less than 0.5 mm. An on-site automated weather station provided meteorological data. Cumulative interception loss for the periods of August-December 2013 and April-July 2014 was 51%. Phenological change did not show a stable pattern of influence on throughfall depths. Measurements in May and July 2014 showed a high variability of stemflow (2-16%) between rain events. Throughfall and precipitation intensities (mm/hr) expressed strong linear relationships (adjusted coefficient of determination R20.79) for the entire range of observed rainfall intensities. The ratio of throughfall to precipitation intensity was 0.49:1. The observations suggest that reduction of throughfall intensity by the canopy during a rainstorm determines the bulk of interception depth. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception. Simulations of potential evaporation based on the Penman-Monteith method revealed a serious underestimation of evaporation from the wet canopy surfaces during the rain events. Mechanisms other than heat balance models of potential evaporation from a still water surface are being discussed in order to explain large intrastorm evaporation from within an isolated canopy.

Model developments in TERRA_URB, the upcoming standard urban parametrization of the atmospheric numerical model COSMO(-CLM)

NASA Astrophysics Data System (ADS)

Wouters, Hendrik; Blahak, Ulrich; Helmert, Jürgen; Raschendorfer, Matthias; Demuzere, Matthias; Fay, Barbara; Trusilova, Kristina; Mironov, Dmitrii; Reinert, Daniel; Lüthi, Daniel; Machulskaya, Ekaterina

2015-04-01

In order to address urban climate at the regional scales, a new efficient urban land-surface parametrization TERRA_URB has been developed and coupled to the atmospheric numerical model COSMO-CLM. Hereby, several new advancements for urban land-surface models are introduced which are crucial for capturing the urban surface-energy balance and its seasonal dependency in the mid-latitudes. This includes a new PDF-based water-storage parametrization for impervious land, the representation of radiative absorption and emission by greenhouse gases in the infra-red spectrum in the urban canopy layer, and the inclusion of heat emission from human activity. TERRA_URB has been applied in offline urban-climate studies during European observation campaigns at Basel (BUBBLE), Toulouse (CAPITOUL), and Singapore, and currently applied in online studies for urban areas in Belgium, Germany, Switzerland, Helsinki, Singapore, and Melbourne. Because of its computational efficiency, high accuracy and its to-the-point conceptual easiness, TERRA_URB has been selected to become the standard urban parametrization of the atmospheric numerical model COSMO(-CLM). This allows for better weather forecasts for temperature and precipitation in cities with COSMO, and an improved assessment of urban outdoor hazards in the context of global climate change and urban expansion with COSMO-CLM. We propose additional extensions to TERRA_URB towards a more robust representation of cities over the world including their structural design. In a first step, COSMO's standard EXTernal PARarameter (EXTPAR) tool is updated for representing the cities into the land cover over the entire globe. Hereby, global datasets in the standard EXTPAR tool are used to retrieve the 'Paved' or 'sealed' surface Fraction (PF) referring to the presence of buildings and streets. Furthermore, new global data sets are incorporated in EXTPAR for describing the Anthropogenic Heat Flux (AHF) due to human activity, and optionally the Surface Area Index (SAI) derived from the Floor Space Index (FSI). In a second step, it is focussed on the urban/rural contrast in terms of turbulent transport in the surface layer by means of model sensivity experiments: On the theoretical basis of the TKE-based surface-layer transfer scheme of COSMO, we investigate the consistency between empirical functions for thermal roughness lengths and the urban/rural canopy morphology.

Sensitivity study of the UHI in the city of Szeged (Hungary) to different offline simulation set-ups using SURFEX/TEB

NASA Astrophysics Data System (ADS)

Zsebeházi, Gabriella; Hamdi, Rafiq; Szépszó, Gabriella

2015-04-01

Urbanised areas modify the local climate due to the physical properties of surface subjects and their morphology. The urban effect on local climate and regional climate change interact, resulting in more serious climate change impacts (e.g., more heatwave events) over cities. Majority of people are now living in cities and thus, affected by these enhanced changes. Therefore, targeted adaptation and mitigation strategies in cities are of high importance. Regional climate models (RCMs) are sufficient tools for estimating future climate change of an area in detail, although most of them cannot represent the urban climate characteristics, because their spatial resolution is too coarse (in general 10-50 km) and they do not use a specific urban parametrization over urbanized areas. To describe the interactions between the urban surface and atmosphere on few km spatial scale, we use the externalised SURFEX land surface scheme including the TEB urban canopy model in offline mode (i.e. the interaction is only one-way). The driving atmospheric conditions highly influence the impact results, thus the good quality of these data is particularly essential. The overall aim of our research is to understand the behaviour of the impact model and its interaction with the forcing coming from the atmospheric model in order to reduce the biases, which can lead to qualified impact studies of climate change over urban areas. As a preliminary test, several short (few-day) 1 km resolution simulations are carried out over a domain covering a Hungarian town, Szeged, which is located at the flat southern part of Hungary. The atmospheric forcing is provided by ALARO (a new version of the limited-area model of the ARPEGE-IFS system running at the Royal Meteorological Institute of Belgium) applied over Hungary. The focal point of our investigations is the ability of SURFEX to simulate the diurnal evolution and spatial pattern of urban heat island (UHI). Different offline simulation set-ups have been tested: 1. Atmospheric forcing at 4km and 10km resolutions; 2. Atmospheric forcing prepared with and without TEB; 3. Coupling of forcings on 3h and 1h temporal frequencies; 4. Different forcing levels on 50m, 40m, 30m, 20m, 10m; 5. Different computation method of 2m temperature using CANOPY, Paulson, and Geleyn schemes. Finally, some outcomes are also compared to the results obtained using ALADIN-Climate RCM (adapted and used at the Hungarian Meteorological Service on 10 km resolution) as driving atmospheric model. The presentation is dedicated to show the results and main conclusions of our studies.

The effect of urban growth on landscape-scale restoration for a fire-dependent songbird.

PubMed

Pickens, Bradley A; Marcus, Jeffrey F; Carpenter, John P; Anderson, Scott; Taillie, Paul J; Collazo, Jaime A

2017-04-15

A landscape-scale perspective on restoration ecology has been advocated, but few studies have informed restoration with landscape metrics or addressed broad-scale threats. Threats such as urban growth may affect restoration effectiveness in a landscape context. Here, we studied longleaf pine savanna in the rapidly urbanizing southeastern United States where a habitat-specialist bird, Bachman's sparrow (Peucaea aestivalis), is closely associated with savanna vegetation structure and frequent fire. Our objectives were to construct a species distribution model for Bachman's sparrow, determine the relationship between fire and urbanization, quantify the urban growth effect (2010-2090), identify potential restoration areas, and determine the interaction between restoration potential and urban growth by 2050. Number of patches, patch size, and isolation metrics were used to evaluate scenarios. The species distribution model was 88% accurate and emphasized multiscale canopy cover characteristics, fire, and percent habitat. Fires were less common <600 m from urban areas, and this fire suppression effect exacerbated urban growth effects. For restoration scenarios, canopy cover reduction by 30% resulted in nearly double the amount of habitat compared to the prescribed fire scenario; canopy cover reduction resulted in larger patch sizes and less patch isolation compared to current conditions. The effect of urban growth on restoration scenarios was unequal. Seventy-four percent of restoration areas from the prescribed fire scenario overlapped with projected urban growth, whereas the canopy cover reduction scenario only overlapped by 9%. We emphasize the benefits of simultaneously considering the effects of urban growth and landscape-scale restoration potential to promote a landscape with greater patch sizes and less isolation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Urban landscape genetics: canopy cover predicts gene flow between white-footed mouse (Peromyscus leucopus) populations in New York City.

PubMed

Munshi-South, Jason

2012-03-01

In this study, I examine the influence of urban canopy cover on gene flow between 15 white-footed mouse (Peromyscus leucopus) populations in New York City parklands. Parks in the urban core are often highly fragmented, leading to rapid genetic differentiation of relatively nonvagile species. However, a diverse array of 'green' spaces may provide dispersal corridors through 'grey' urban infrastructure. I identify urban landscape features that promote genetic connectivity in an urban environment and compare the success of two different landscape connectivity approaches at explaining gene flow. Gene flow was associated with 'effective distances' between populations that were calculated based on per cent tree canopy cover using two different approaches: (i) isolation by effective distance (IED) that calculates the single best pathway to minimize passage through high-resistance (i.e. low canopy cover) areas, and (ii) isolation by resistance (IBR), an implementation of circuit theory that identifies all low-resistance paths through the landscape. IBR, but not IED, models were significantly associated with three measures of gene flow (Nm from F(ST) , BayesAss+ and Migrate-n) after factoring out the influence of isolation by distance using partial Mantel tests. Predicted corridors for gene flow between city parks were largely narrow, linear parklands or vegetated spaces that are not managed for wildlife, such as cemeteries and roadway medians. These results have implications for understanding the impacts of urbanization trends on native wildlife, as well as for urban reforestation efforts that aim to improve urban ecosystem processes. © 2012 Blackwell Publishing Ltd.

Optimizing the Determination of Roughness Parameters for Model Urban Canopies

NASA Astrophysics Data System (ADS)

Huq, Pablo; Rahman, Auvi

2018-05-01

We present an objective optimization procedure to determine the roughness parameters for very rough boundary-layer flow over model urban canopies. For neutral stratification the mean velocity profile above a model urban canopy is described by the logarithmic law together with the set of roughness parameters of displacement height d, roughness length z_0 , and friction velocity u_* . Traditionally, values of these roughness parameters are obtained by fitting the logarithmic law through (all) the data points comprising the velocity profile. The new procedure generates unique velocity profiles from subsets or combinations of the data points of the original velocity profile, after which all possible profiles are examined. Each of the generated profiles is fitted to the logarithmic law for a sequence of values of d, with the representative value of d obtained from the minima of the summed least-squares errors for all the generated profiles. The representative values of z_0 and u_* are identified by the peak in the bivariate histogram of z_0 and u_* . The methodology has been verified against laboratory datasets of flow above model urban canopies.

Investigating the vertical dimension of Singapore's urban heat island through quadcopter platforms: an pilot study

NASA Astrophysics Data System (ADS)

Chow, Winston; Ho, Dawn

2016-04-01

In numerous cities, measurements of urban warmth in most urban heat island (UHI) studies are generally constrained towards surface or near-surface (<2 m above surface level) levels across horizontal variations in land use and land cover. However, there has been hitherto limited attention towards the measurement of vertical temperature profiles extending from the urban surface, urban canopy layer through to the urban boundary layer. Knowledge of these profiles, through (a.) how they vary over different local urban morphologies, and (b.) develop with respect to synoptic meteorological conditions, are important towards several aspects of UHI research; these include validating modelling urban canopy lapse rate profiles or estimating the growth of urban plumes. In this novel study, we utilised temperature sensor-loggers attached onto remote controlled aerial quadcopter platforms to measure urban temperature profiles up to 100 m above ground level in Singapore, which is a rapidly urbanizing major tropical metropolis. Three different land use/land cover categories were sampled; a high-rise residential estate, a university campus, and an urban park/green-space. Sorties were flown repeatedly at four different times - sunrise, noon, sunset and midnight. Initial results indicate significant variations in intra-site stability and inversion development between the urban canopy and boundary layers. These profiles are also temporally dynamic, depending on the time of day and larger-scale weather conditions.

Mapping Urban Tree Canopy Coverage and Structure using Data Fusion of High Resolution Satellite Imagery and Aerial Lidar

NASA Astrophysics Data System (ADS)

Elmes, A.; Rogan, J.; Williams, C. A.; Martin, D. G.; Ratick, S.; Nowak, D.

2015-12-01

Urban tree canopy (UTC) coverage is a critical component of sustainable urban areas. Trees provide a number of important ecosystem services, including air pollution mitigation, water runoff control, and aesthetic and cultural values. Critically, urban trees also act to mitigate the urban heat island (UHI) effect by shading impervious surfaces and via evaporative cooling. The cooling effect of urban trees can be seen locally, with individual trees reducing home HVAC costs, and at a citywide scale, reducing the extent and magnitude of an urban areas UHI. In order to accurately model the ecosystem services of a given urban forest, it is essential to map in detail the condition and composition of these trees at a fine scale, capturing individual tree crowns and their vertical structure. This paper presents methods for delineating UTC and measuring canopy structure at fine spatial resolution (<1m). These metrics are essential for modeling the HVAC benefits from UTC for individual homes, and for assessing the ecosystem services for entire urban areas. Such maps have previously been made using a variety of methods, typically relying on high resolution aerial or satellite imagery. This paper seeks to contribute to this growing body of methods, relying on a data fusion method to combine the information contained in high resolution WorldView-3 satellite imagery and aerial lidar data using an object-based image classification approach. The study area, Worcester, MA, has recently undergone a large-scale tree removal and reforestation program, following a pest eradication effort. Therefore, the urban canopy in this location provides a wide mix of tree age class and functional type, ideal for illustrating the effectiveness of the proposed methods. Early results show that the object-based classifier is indeed capable of identifying individual tree crowns, while continued research will focus on extracting crown structural characteristics using lidar-derived metrics. Ultimately, the resulting fine resolution UTC map will be compared with previously created UTC maps of the same area but for earlier dates, producing a canopy change map corresponding to the Worcester area tree removal and replanting effort.

Tree Canopy Cover Mapping Using LiDAR in Urban Barangays of Cebu City, Central Philippines

NASA Astrophysics Data System (ADS)

Ejares, J. A.; Violanda, R. R.; Diola, A. G.; Dy, D. T.; Otadoy, J. B.; Otadoy, R. E. S.

2016-06-01

This paper investigates tree canopy cover mapping of urban barangays (smallest administrative division in the Philippines) in Cebu City using LiDAR (Light Detection and Ranging). Object-Based Image Analysis (OBIA) was used to extract tree canopy cover. Multi-resolution segmentation and a series of assign-class algorithm in eCognition software was also performed to extract different land features. Contextual features of tree canopies such as height, area, roundness, slope, length-width and elliptic fit were also evaluated. The results showed that at the time the LiDAR data was collected (June 24, 2014), the tree cover was around 25.11 % (or 15,674,341.8 m2) of the city's urban barangays (or 62,426,064.6 m2). Among all urban barangays in Cebu City, Barangay Busay had the highest cover (55.79 %) while barangay Suba had the lowest (0.8 %). The 16 barangays with less than 10 % tree cover were generally located in the coastal area, presumably due to accelerated urbanization. Thirty-one barangays have tree cover ranging from 10.59--27.3 %. Only 3 barangays (i.e., Lahug, Talamban, and Busay) have tree cover greater than 30 %. The overall accuracy of the analysis was 96.6 % with the Kappa Index of Agreement or KIA of 0.9. From the study, a grouping can be made of the city's urban barangays with regards to tree cover. The grouping will be useful to urban planners not only in allocating budget to the tree planting program of the city but also in planning and creation of urban parks and playgrounds.

Environmental Response of Small Urban Parks in Context of Dhaka City

NASA Astrophysics Data System (ADS)

Tabassum, S.

2018-01-01

Urban green spaces are essential element of urban life which, due to their structure and multi functionality, can play an exemplary role in the vitality and quality of urban life. Urban Parks are not only used as active recreational and leisure areas for its citizens but also an important catalyst for community development and enhancement. These spaces in the city act like its lungs and play a critical role in supporting the ecological and environmental system. In the dense urban areas, even Small Parks (less than one acre in size) can also contribute a lot to improve environmental quality of city life. In a populated city where it is difficult to incorporate large Public Parks, these small green area can complement large Public Park system. Accordingly the study is concerned to evaluate the environmental performances of Small Parks on the built environments of urban Dhaka. The analysis identifies that Small Parks has strong environmental impact, the intensity of which depends on the type and quality of its vegetation, its design parameters, connectivity and of course on surrounding urban morphology. And it is confirmed that park with more canopy tree is suitable for our environment and therefore a good combination of vegetation (wide canopy trees at periphery, medium canopy trees beside internal walkway and small canopy tree, shrub and grass cover elsewhere) are recommended for better environmental performance of Small Parks. The research will be an approach to find the ways and means to restore the Small Parks of Dhaka city to ensure the livability of the city and enhance the quality of city image.

Fast matrix treatment of 3-D radiative transfer in vegetation canopies: SPARTACUS-Vegetation 1.1

NASA Astrophysics Data System (ADS)

Hogan, Robin J.; Quaife, Tristan; Braghiere, Renato

2018-01-01

A fast scheme is described to compute the 3-D interaction of solar radiation with vegetation canopies. The canopy is split in the horizontal plane into one clear region and one or more vegetated regions, and the two-stream equations are used for each, but with additional terms representing lateral exchange of radiation between regions that are proportional to the area of the interface between them. The resulting coupled set of ordinary differential equations is solved using the matrix-exponential method. The scheme is compared to solar Monte Carlo calculations for idealized scenes from the RAMI4PILPS intercomparison project, for open forest canopies and shrublands both with and without snow on the ground. Agreement is good in both the visible and infrared: for the cases compared, the root-mean-squared difference in reflectance, transmittance and canopy absorptance is 0.020, 0.038 and 0.033, respectively. The technique has potential application to weather and climate modelling.

A Note on Spatial Averaging and Shear Stresses Within Urban Canopies

NASA Astrophysics Data System (ADS)

Xie, Zheng-Tong; Fuka, Vladimir

2018-04-01

One-dimensional urban models embedded in mesoscale numerical models may place several grid points within the urban canopy. This requires an accurate parametrization for shear stresses (i.e. vertical momentum fluxes) including the dispersive stress and momentum sinks at these points. We used a case study with a packing density of 33% and checked rigorously the vertical variation of spatially-averaged total shear stress, which can be used in a one-dimensional column urban model. We found that the intrinsic spatial average, in which the volume or area of the solid parts are not included in the average process, yield greater time-spatial average of total stress within the canopy and a more evident abrupt change at the top of the buildings than the comprehensive spatial average, in which the volume or area of the solid parts are included in the average.

A high-resolution large-eddy simulation of turbulent flow within and above urban-like canopies

NASA Astrophysics Data System (ADS)

Maché, M.; Calmet, I.; Sini, J.-F.

2009-09-01

The urban microclimate is a result of the interactions between regional climatology, morphology of urban fabric and thermo-radiative and hydric properties of the materials constituting the urban surfaces. Modern urban planning tries to compact cities for avoiding spreading of the town area in order to reduce the need of transports. The climatic effects of this politic are not well known yet. This work is the first step of a study whose main purpose is to propose an urban planning politic which considers the urban heat island within the context of the climate change. Therefore it aims to understand the effects of building configuration on the momentum, heat and humidity turbulent transfers. Urban structures are quite heterogeneous and complex. To analyse the interactions between urban canopies and the atmosphere, the resolution has to be high enough that mean flow characteristics between the buildings can be observed as well as turbulent structures that develop above roof level. For that purpose, the Large-Eddy Simulation atmospheric model ARPS (Advanced Regional Prediction System) is employed. The subgrid scales are modelled by means of the resolution of an equation for the subgrid-scale turbulent kinetic energy. The version used is this study is based on the developments of Dupont & Brunet (2008) who introduced a drag force approach to simulate the influence of the vegetal covers on the low atmosphere. The application of this model on urban canopies requires adjusting the drag coefficient (Cd) in function of the frontal density (Af) and of the building arrangement. Its dependency on configuration (staggered or aligned arrays) and on frontal density is investigated. In order to put in light the main characteristics of the flow field and to validate the model in urban configurations, the turbulent flow above arrays of obstacles is investigated here for different arrangements and packing densities. The grid spacing is set to a few tens of meters in both horizontal directions and one meter in vertical direction, within the canopy. Above the canopy, grids are stretched vertically to reach four meters in average. The surface density Af is calculated in function of the geometry of the obstacles present in a grid cell. The effect of Cd values on the turbulent statistics is compared with results from wind tunnel experiments or building resolving simulations. The ability of the model to reproduce the major turbulent organized structures above the canopy and the influence of the building configuration is also studied, in terms of intensity, size and orientation of the structures. Further research will be done to investigate the effect of configuration of buildings with more complex geometries, like variable building height, on turbulent flow characteristics. To understand the climatologic features of a real city this approach will be completed by the introduction of a parametrization for heat and humidity exchanges inside the canopy.

Controls on Biogeochemical Cycling of Nitrogen in Urban Ecosystems

NASA Astrophysics Data System (ADS)

Templer, P. H.; Hutyra, L.; Decina, S.; Rao, P.; Gately, C.

2017-12-01

Rates of atmospheric nitrogen deposition are declining across much of the United States and Europe, yet they remain substantially elevated by almost an order of magnitude over pre-industrial levels and occur as hot spots in urban areas. We measured atmospheric inputs of inorganic and organic nitrogen in multiple urban sites around the Boston Metropolitan area, finding that urban rates are substantially elevated compared to nearby rural areas, and that the range of these atmospheric inputs are as large as observed urban to rural gradients. Within the City of Boston, the variation in deposition fluxes can be explained by traffic intensity, vehicle emissions, and spring fertilizer additions. Throughfall inputs of nitrogen are approximately three times greater than bulk deposition inputs in the city, demonstrating that the urban canopy amplifies rates of nitrogen reaching the ground surface. Similar to many other metropolitan areas of the United States, the City of Boston has 25% canopy cover; however, 25% of this tree canopy is located above impervious pavement. Throughfall inputs that do not have soil below the canopy to retain excess nitrogen may lead to greater inputs of nitrogen into nearby waterways through runoff. Most measurement stations for atmospheric nitrogen deposition are intentionally located away from urban areas and point sources of pollution to capture regional trends. Our data show that a major consequence of this network design is that hotspots of nitrogen deposition and runoff into urban and coastal waterways is likely underestimated to a significant degree. A more complete determination of atmospheric nitrogen deposition and its fate in urban ecosystems is critical for closing regional nitrogen budgets and for improving our understanding of biogeochemical nitrogen cycling across multiple spatial scales.

Determining light requirements of groundcover plants from subtropical natural forest using hemispherical photography

NASA Astrophysics Data System (ADS)

Zhang, Yi; Zhong, Yonglin; Xu, Mingfeng; Su, Zhiyao

2017-01-01

In order to determine light requirements of indigenous groundcover plants for potential use in urban landscaping, we conducted a plant census in Yinpingshan Nature Reserve, Dongguan, China, and measured canopy structure and understory light regimes using hemispherical photography. We found that canopy openness, transmitted direct solar radiation, and transmitted diffuse solar radiation exhibited highly significant spatial heterogeneity. Species composition and diversity of groundcover plants were highly dependent on canopy structure and understory light condition. Greater diversity and more stems of groundcover plants were associated with greater canopy openness and understory radiation in most cases. Highly significant differences in species composition were detected along canopy openness, transmitted direct solar radiation, and transmitted diffuse solar radiation gradients, respectively. We also detected indicator species for specific understory light regimes, which will provide useful information when applying such species in urban greening under various light environments.

A comparison of two sampling approaches for assessing the urban forest canopy cover from aerial photography.

Treesearch

Ucar Zennure; Pete Bettinger; Krista Merry; Jacek Siry; J.M. Bowker

2016-01-01

Two different sampling approaches for estimating urban tree canopy cover were applied to two medium-sized cities in the United States, in conjunction with two freely available remotely sensed imagery products. A random point-based sampling approach, which involved 1000 sample points, was compared against a plot/grid sampling (cluster sampling) approach that involved a...

Trees grow on money: Urban tree canopy cover and environmental justice

Treesearch

Kirsten Schwarz; Michail Fragkias; Christopher G. Boone; Weiqi Zhou; Melissa McHale; J. Morgan Grove; Jarlath O' Neil-Dunne; Joseph P. McFadden; Geoffrey L. Buckley; Dan Childers; Laura Ogden; Stephanie Pincetl; Diane Pataki; Ali Whitmer; Mary L. Cadenasso; Steven Arthur Loiselle

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman’s correlation, ordinary least squares...

Implication of Intrastorm Rainfall-Canopy Interaction on Interception Performance of Broadleaf Evergreen Shrubs in an Ultra-Urban Setting

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.

2015-12-01

Because of its ability to intercept a portion of rainfall, vegetated canopies can play substantial role in modulating the urban hydrological cycle. However, canopy interception research has historically been focused to forest canopies. The goal of our research is to quantify rainfall partitioning by isolated evergreen shrub canopies in an ultra-urban setting. The three year field experiment involved three exemplars of cherry laurel (Prunus laurocerasus 'Otto Luyken'.) Ten rain gauges positioned under each plant were used to measure throughfall with a sampling frequency of five seconds. A number of specific techniques were implemented to minimize error associated with the gauges, e.g., splash-in, splash-out and excessive wetting. The cumulative throughfall deficit (i.e., gross precipitation minus throughfall within the canopy projected area and minus stemflow) for the periods of August-December 2013, April-December 2014 and April-July 2015 was 39%. Spatial variability of throughfall was large (coefficient of variation up to 1.5.) Stable areas of preferential throughfall flux were observed. Stemflow showed a high variability (1.4 - 24%) between rain events. The relationship between throughfall and precipitation intensity was strongly linear (adjusted coefficient of determination R2 0.79) throughout the entire range of observed rainfall intensities. The overall ratio of throughfall to precipitation intensity was 0.48:1. The observations suggest that reduction of throughfall intensity by the canopy during a rainstorm determines the aggregate interception depth. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception loss. Penman-Monteith estimates of wet canopy evaporation cannot account for the throughfall deficit. Lateral displacement of microdrops beyond the canopy projected area is another phenomenon that will be discussed and most recent observations of an extended gauge network will be presented.

Investigation of the flow inside an urban canopy immersed into an atmospheric boundary layer using laser Doppler anemometry

NASA Astrophysics Data System (ADS)

Herpin, Sophie; Perret, Laurent; Mathis, Romain; Tanguy, Christian; Lasserre, Jean-Jacques

2018-05-01

Laser Doppler anemometry (LDA) is used to investigate the flow inside an idealized urban canopy consisting of a staggered array of cubes with a 25% density immersed into an atmospheric boundary layer with a Reynolds number of δ ^+=32{,}300. The boundary layer thickness to cube height ratio (δ /h=22.7) is large enough to be representative of atmospheric surface layer in neutral conditions. The LDA measurements give access to pointwise time-resolved data at several positions inside the canopy (z=h/4, h/2, and h). Synchronized hot-wire measurements above the canopy (inertial region and roughness sublayer) are also realized to get access to interactions between the different flow regions. The wall-normal mean velocity profile and Reynolds stresses show a good agreement with available data in the literature, although some differences are observed on the standard deviation of the spanwise component. A detailed spectral and integral time scale analysis inside the canopy is then carried out. No clear footprint of a periodic vortex shedding on the sides of the cubes could be identified on the power spectra, owing to the multiple cube-to-cube interactions occuring within a canopy with a building density in the wake interference regime. Results also suggest that interactions between the most energetics scales of the boundary layer and those related to the cube canopy take place, leading to a broadening of the energy peak in the spectra within the canopy. This is confirmed by the analysis of coherence results between the flow inside and above the canopy. It is shown that linear interactions mechanisms are significant, but reduced compared to smooth-wall boundary-layer flow. To our knowledge, this is the first time such results are shown on the dynamics of the flow inside an urban canopy.

On the urban land-surface impact on climate over Central Europe

NASA Astrophysics Data System (ADS)

Huszar, Peter; Halenka, Tomas; Belda, Michal; Zemankova, Katerina; Zak, Michal

2014-05-01

For the purpose of qualifying and quantifying the impact of cities and in general the urban surfaces on climate over central Europe, the surface parameterization in regional climate model RegCM4 has been extended with the Single Layer Urban Canopy Model (SLUCM) for urban and suburban land surface. This can be used both in dynamic scale within BATS scheme and in a more detailed SUBBATS scale to treat the surface processes on a higher resolution subgrid. A set of experiments was performed over the period of 2005-2009 over central Europe, either without considering urban surfaces and with the SLUCM treatment. Results show a statistically significant impact of urbanized surfaces on temperature (up to 1.5 K increase in summer), on the boundary layer height (ZPBL, increases up to 50 m). Urbanization further influences surface wind with a winter decrease up to -0,6 m s-1 and both increases and decreases in summer depending the location with respect to cities and daytime (changes up to 0.3 ms-1). Urban surfaces significantly reduce evaporation and thus the humidity over the surface. This impacts in our simulations the summer precipitation rate showing decrease over cities up to - 2 mm day-1. We further showed, that significant temperature increases are not limited to the urban canopy layer but spawn the whole boundary layer. Above that, a small but statistically significant temperature decrease is modeled. The comparison with observational data showed significant improvement in modeling the monthly surface temperatures in summer and the models better describe the diurnal temperature variation reducing the afternoon and evening bias due to the UHI development, which was not captured by the model if one does not apply the urban parameterization. Sensitivity experiments were carried out as well to quantify the response of the meteorological conditions to changes in the parameters specific to the urban environment such as street width, building height, albedo of the roofs, anthropogenic heat release etc. and showed that the results are rather robust and the choice of the key SLUCM parameters impacts the results only slightly (mainly temperature, ZPBL and wind velocity). Further, the important conclusion is that statistically significant impacts are modeled not only over large urbanized areas (cities), but the influence of cities is evident over remote rural areas as well with minor or without any urban surfaces. We show that this is the result of the combined effect of the distant influence of surrounding cities and the influence of the minor local urban surface coverage.

The impact of urban canopy meteorological forcing on summer photochemistry

NASA Astrophysics Data System (ADS)

Huszár, Peter; Karlický, Jan; Belda, Michal; Halenka, Tomáš; Pišoft, Petr

2018-03-01

The regional climate model RegCM4.4, including the surface model CLM4.5, was offline coupled to the chemistry transport model CAMx version 6.30 in order to investigate the impact of the urban canopy induced meteorological changes on the longterm summer photochemistry over central Europe for the 2001-2005 period. First, the urban canopy impact on the meteorological conditions was calculated performing a reference experiment without urban landsurface considered and an experiment with urban surfaces modeled with the urban parameterization within the CLM4.5 model. In accordance with expectations, strong increases of urban surface temperatures (up to 2-3 K), decreases of wind speed (up to -1 ms-1) and increases of vertical turbulent diffusion coefficient (up to 60-70 m2s-1) were found. For the impact on chemistry, these three components were considered. Additionally, we accounted for the effect of temperature enhanced biogenic emission increase. Several experiments were performed by adding these effects one-by-one to the total impact: i.e., first, only the urban temperature impact was considered driving the chemistry model; secondly, the wind impact was added and so on. We found that the impact on biogenic emission account for minor changes in the concentrations of ozone (O3), oxides of nitrogen NOx = NO + NO2 and nitric acid (HNO3). On the other hand, the dominating component acting is the increased vertical mixing, resulting in up to 5 ppbv increase of urban ozone concentrations while causing -2 to -3 ppbv decreases and around 1 ppbv increases of NOx and HNO3 surface concentrations, respectively. The temperature impact alone results in reduction of ozone, increase in NO, decrease in NO2 and increases of HNO3. The wind impact leads, over urban areas, to ozone decreases, increases of NOx and a slight increase in HNO3. The overall impact is similar to the impact of increased vertical mixing alone. The Process Analysis (PA) technique implemented in CAMx was adopted to investigate the causes of the modeled impacts in more details. It showed that the main process contributing to the temperature impact on ozone is a dry-deposition enhancement, while the dominating process controlling the wind impact on ozone over cities is the advection reduction. In case of the impact of enhanced turbulence, PA suggests that ozone increases are, again as assumed, the result of increased downward vertical mixing supported by reduced chemical loss. Comparing the model concentrations with measurements over urban areas, a slight improvement of the model performance was achieved during afternoon hours if urban canopy forcing on chemistry via meteorology was accounted for. The study demonstrates that disregarding the urban canopy induced meteorological effects in air-quality oriented modeling studies can lead to erroneous results in the calculated species concentrations. However, it also shows that the individual components are not equally important: urban canopy induced turbulence effects dominate while the wind-speed and temperature related ones are of considerably smaller magnitude.

Improved Monitoring of Vegetation Productivity using Continuous Assimilation of Radiometric Data

NASA Astrophysics Data System (ADS)

Baret, F.; Lauvernet, C.; Weiss, M.; Prevot, L.; Rochdi, N.

Canopy functioning models describe crop production from meteorological and soil inputs. However, because of the large number of variables and parameters used, and the poor knowledge of the actual values of some of them, the time course of the canopy and thus final production simulated by these models is often not very accurate. Satellite observations sensors allow controlling the simulations through assimilation of the radiometric data within radiative transfer models coupled to canopy functioning models. An assimilation scheme is presented with application to wheat crops. The coupling between radiative transfer models and canopy functioning models is described. The assimilation scheme is then applied to an experiment achieved within the ReSeDA project. Several issues relative to the assimilation process are discussed. They concern the type of canopy functioning model used, the possibility to assimilate biophysical products rather than radiances, and the use of ancillary information. Further, considerations associated to the problems linked to high spatial and temporal resolution data are listed and illustrated by preliminary results acquired within the ADAM project. Further discussion is made on the required temporal sampling for space observations.

Dispersion of a Passive Scalar Within and Above an Urban Street Network

NASA Astrophysics Data System (ADS)

Goulart, E. V.; Coceal, O.; Belcher, S. E.

2018-03-01

The transport of a passive scalar from a continuous point-source release in an urban street network is studied using direct numerical simulation (DNS). Dispersion through the network is characterized by evaluating horizontal fluxes of scalar within and above the urban canopy and vertical exchange fluxes through the canopy top. The relative magnitude and balance of these fluxes are used to distinguish three different regions relative to the source location: a near-field region, a transition region and a far-field region. The partitioning of each of these fluxes into mean and turbulent parts is computed. It is shown that within the canopy the horizontal turbulent flux in the street network is small, whereas above the canopy it comprises a significant fraction of the total flux. Vertical fluxes through the canopy top are predominantly turbulent. The mean and turbulent fluxes are respectively parametrized in terms of an advection velocity and a detrainment velocity and the parametrization incorporated into a simple box-network model. The model treats the coupled dispersion problem within and above the street network in a unified way and predictions of mean concentrations compare well with the DNS data. This demonstrates the usefulness of the box-network approach for process studies and interpretation of results from more detailed numerical simulations.

Evaluation des apports solaires a l'echelle d'un quartier urbain en periode de chauffe selon sa typologie, son orientation et sa latitude dans un contexte de densification de la ville

NASA Astrophysics Data System (ADS)

Chenard, Laurent

Mass urbanization is a major issue for town administrators. Population increase will have an impact on the quality of the environment for citizens. Government will have to take decisions to limit those effects. Green energies are part of the solution to reach fixed goals by the public administration for sustainable development. Passive solar energy is studied in this work in an urban canopy located in five different towns: San Francisco, Montreal, Bordeaux, Lyon and Stockholm. Passive solar energy is calculated in the heating season. Direct and diffuse solar radiation is considered by using the Perez model. Radiosity is not taken into account. Heating demand is calculated by the heating degree day method. Seven urban forms have been created to determine the amount of solar energy entering in every window of the urban canopy while taking into account urban context and forms. Optimal orientation of the canopy shows an increase of 5% of the passive solar radiation from original orientation, 180 degrees rotation from first orientation straight south. This value goes lower when stories are added to the urban context. A rotation of 90 degrees from the first orientation shows a decrease of 6 to 15% in solar passive gain. Densification of the urban canopy by adding stories to the buildings results in a loss up to 65% of the solar gain for the first story. It is showed that solar passive energy has a low ratio of 5% for space heating for old buildings, 1960 constructions. Today's buildings have a difference between passive solar energy and heating demand of 10 to 75% depending on the model and location.

A better way of representing stem area index in two-big-leaf models: the application and impact on canopy integration of leaf nitrogen content

NASA Astrophysics Data System (ADS)

Chen, M.; Butler, E. E.; Wythers, K. R.; Kattge, J.; Ricciuto, D. M.; Thornton, P. E.; Atkin, O. K.; Flores-Moreno, H.; Reich, P. B.

2017-12-01

In order to better estimate the carbon budget of the globe, accurately simulating gross primary productivity (GPP) in earth system models is critical. When upscaling leaf level photosynthesis to the canopy, climate models uses different big-leaf schemes. About half of the state-of-the-art earth system models use a "two-big-leaf" scheme that partitions canopies into direct and diffusively illuminated fractions to reduce high bias of GPP simulated by one-big-leaf models. Some two-big-leaf models, such as ACME (identical in this respect to CLM 4.5) add leaf area index (LAI) and stem area index (SAI) together when calculating canopy radiation transfer. This treatment, however, will result in higher fraction of sunlit leaves. It will also lead to an artificial overestimation of canopy nitrogen content. Here we introduce a new algorithm of simulating SAI in a two-big-leaf model. The new algorithm reduced the sunlit leave fraction of the canopy and conserved the nitrogen content from leaf to canopy level. The lower fraction of sunlit leaves reduced global GPP especially in tropical area. Compared to the default model, for the past 100 years (1909-2009), the averaged global annual GPP is lowered by 4.11 PgC year-1 using this new algorithm.

Atmospheric Inputs of Nitrogen, Carbon, and Phosphorus across an Urban Area: Unaccounted Fluxes and Canopy Influences

NASA Astrophysics Data System (ADS)

Decina, Stephen M.; Templer, Pamela H.; Hutyra, Lucy R.

2018-02-01

Rates of atmospheric deposition are declining across the United States, yet urban areas remain hotspots of atmospheric deposition. While past studies show elevated rates of inorganic nitrogen (N) deposition in cities, less is known about atmospheric inputs of organic N, organic carbon (C), and organic and inorganic phosphorus (P), all of which can affect ecosystem processes, water quality, and air quality. Further, the effect of the tree canopy on amounts and forms of nutrients reaching urban ground surfaces is not well-characterized. We measured growing season rates of total N, organic C, and total P in bulk atmospheric inputs, throughfall, and soil solution around the greater Boston area. We found that organic N constitutes a third of total N inputs, organic C inputs are comparable to rural inputs, and inorganic P inputs are 1.2 times higher than those in sewage effluent. Atmospheric inputs are enhanced two-to-eight times in late spring and are elevated beneath tree canopies, suggesting that trees augment atmospheric inputs to ground surfaces. Additionally, throughfall inputs may directly enter runoff when trees extend above impervious surfaces, as is the case with 26.1% of Boston's tree canopy. Our results indicate that the urban atmosphere is a significant source of elemental inputs that may impact urban ecosystems and efforts to improve water quality, particularly in terms of P. Further, as cities create policies encouraging tree planting to provide ecosystem services, locating trees above permeable surfaces to reduce runoff nutrient loads may be essential to managing urban biogeochemical cycling and water quality.

Emerald ash borer and the urban forest: Changes in landslide potential due to canopy loss scenarios in the City of Pittsburgh, PA.

PubMed

Pfeil-McCullough, Erin; Bain, Daniel J; Bergman, Jeffery; Crumrine, Danielle

2015-12-01

Emerald ash borer is expected to kill thousands of ash trees in the eastern U.S. This research develops tools to predict the effect of ash tree loss from the urban canopy on landslide susceptibility in Pittsburgh, PA. A spatial model was built using the SINMAP (Stability INdex MAPping) model coupled with spatially explicit scenarios of tree loss (0%, 25%, 50%, and 75% loss of ash trees from the canopy). Ash spatial distributions were estimated via Monte Carlo methods and available vegetation plot data. Ash trees are most prevalent on steeper slopes, likely due to urban development patterns. Therefore, ash loss disproportionately increases hillslope instability. A 75% loss of ash resulted in roughly 800 new potential landslide initiation locations. Sensitivity testing reveals that variations in rainfall rates, and friction angles produce minor changes to model results relative to the magnitude of parameter variation, but reveal high model sensitivity to soil density and root cohesion values. The model predictions demonstrate the importance of large canopy species to urban hillslope stability, particularly on steep slopes and in areas where soils tend to retain water. To improve instability predictions, better characterization of urban soils, particularly spatial patterns of compaction and species specific root cohesion is necessary. The modeling framework developed in this research will enhance assessment of changes in landslide risk due to tree mortality, improving our ability to design economically and ecologically sustainable urban systems. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of Stability on Mixing in Open Canopies. Chapter 4

NASA Technical Reports Server (NTRS)

Lee, Young-Hee; Mahrt, L.

2005-01-01

In open canopies, the within-canopy flux from the ground surface and understory can account for a significant fraction of the total flux above the canopy. This study incorporates the important influence of within-canopy stability on turbulent mixing and subcanopy fluxes into a first-order closure scheme. Toward this goal, we analyze within-canopy eddy-correlation data from the old aspen site in the Boreal Ecosystem - Atmosphere Study (BOREAS) and a mature ponderosa pine site in Central Oregon, USA. A formulation of within-canopy transport is framed in terms of a stability- dependent mixing length, which approaches Monin-Obukhov similarity theory above the canopy roughness sublayer. The new simple formulation is an improvement upon the usual neglect of the influence of within-canopy stability in simple models. However, frequent well-defined cold air drainage within the pine subcanopy inversion reduces the utility of simple models for nocturnal transport. Other shortcomings of the formulation are discussed.

The study of ozone variations in the Las Vegas metropolitan area using remote sensing information and ground observations

USGS Publications Warehouse

Xian, G.; Crane, M.

2006-01-01

Urban development in the Las Vegas Valley, Nevada, has grown rapidly in the past fifty years. Associated with this growth has been a change in landscape from natural cover types to developed urban land mixed with planned vegetation canopy throughout in the metropolitan area. Air quality in the Las Vegas Valley has been affected by increases in anthropogenic emissions and concentrations of carbon monoxide, ozone, and criteria pollutants of particular matter. Ozone concentration in the region is generally influenced by synoptic and mesoscale meteorological conditions, as well as regional transport of pollutants from the western side of Las Vegas. Local influences from ground-level nitrogen oxide emissions and vegetation canopy coverage also affect ozone concentration. Multi-year observational data collected by a network of local air monitoring stations in Clark County, Nevada, indicate that ozone maximums develop in May and June, while minimums exist primarily from November to February. Ozone concentrations are high on the west and northwest sides of the valley. A nighttime ozone reduction in the urban area characterizes the heterogeneous features of spatial distribution for average ozone levels in the Las Vegas urban area. The urban vegetation canopy has a locally positive effect by reducing ozone in urban areas. Decreased ozone levels associated with increased urban development density suggests that the highest ozone concentrations are associated with medium- to low-density urban development in Las Vegas.

Evaluation of an urban vegetative canopy scheme and impact on plume dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, Matthew A; Williams, Michael D; Zajic, Dragan

2009-01-01

The Quick Urban and Industrial Complex (QUIC) atmospheric dispersion modeling system attempts to fill an important gap between the fast, but nonbuilding-aware Gaussian plume models and the building-aware but slow computational fluid dynamics (CFD) models. While Gaussian models have the ability to give answers quickly to emergency responders, they are unlikely to be able to adequately account for the effects of the building-induced complex flow patterns on the near-source dispersion of contaminants. QUIC uses a diagnostic massconsistent empirical wind model called QUIC-URB that is based on the methodology of Rockle (1990), (see also Kaplan and Dinar 1996). In this approach,more » the recirculation zones that form around and between buildings are inserted into the flow using empirical parameterizations and then the wind field is forced to be mass consistent. Although not as accurate as CFD codes, this approach is several orders of magnitude faster and accounts for the bulk effects of buildings.« less

Increasing of Urban Radiation due to Climate Change and Reduction Strategy using Vegetation

NASA Astrophysics Data System (ADS)

Park, C.; Lee, D.; Heo, H. K.; Ahn, S.

2017-12-01

Urban Heat Island (UHI) which means urban air temperature is higher than suburban area is one of the most important environmental issues in Urban. High density of buildings and high ratio of impervious surfaces increases the radiation fluxes in urban canopy. Furthermore, climate change is expected to make UHI even more seriously in the future. Increased irradiation and air temperature cause high amount of short wave and long wave radiation, respectively. This increases net radiation negatively affects heat condition of pedestrian. UHI threatens citizen's health by increasing violence and heat related diseases. For this reason, understanding how much urban radiation will increase in the future, and exploring radiation reduction strategies is important for reducing UHI. In this research, we aim to reveal how the radiation flux in the urban canyon will change as the climate change and determine how much of urban vegetation will be needed to cover this degradation. The study area is a commercial district in Seoul where highly populated area. Due to the high density of buildings and lack of urban vegetation, this area has a poor thermal condition in summer. In this research, we simulate the radiation flux on the ground using multi-layer urban canopy model. Unlike conventionally used urban canopy model to simulate radiation transfer using vertically single layer, the multi-layer model we used here, enables to consider the vertical heterogeneous of buildings and urban vegetation. As a result, net radiation of urban ground will be increase 2.1 W/m² in the 2050s and 2.7 W/m² in the 2100s. And to prevent the increase of radiation, it is revealed that the urban vegetation should by increased by 10%. This research will be valuable in establishing greening planning as a strategy to reduce UHI effect.

Source diagnostics of polycyclic aromatic hydrocarbons in urban road runoff, dust, rain and canopy throughfall.

PubMed

Zhang, Wei; Zhang, Shucai; Wan, Chao; Yue, Dapan; Ye, Youbin; Wang, Xuejun

2008-06-01

Diagnostic ratios and multivariate analysis were utilized to apportion polycyclic aromatic hydrocarbon (PAH) sources for road runoff, road dust, rain and canopy throughfall based on samples collected in an urban area of Beijing, China. Three sampling sites representing vehicle lane, bicycle lane and branch road were selected. For road runoff and road dust, vehicular emission and coal combustion were identified as major sources, and the source contributions varied among the sampling sites. For rain, three principal components were apportioned representing coal/oil combustion (54%), vehicular emission (34%) and coking (12%). For canopy throughfall, vehicular emission (56%), coal combustion (30%) and oil combustion (14%) were identified as major sources. Overall, the PAH's source for road runoff mainly reflected that for road dust. Despite site-specific sources, the findings at the study area provided a general picture of PAHs sources for the road runoff system in urban area of Beijing.

Analysis of the effect of evergreen and deciduous trees on urban nitrogen dioxide levels in the U.S. using land-use regression

NASA Astrophysics Data System (ADS)

Rao, M.; George, L. A.

2012-12-01

Nitrogen dioxide (NO2), an atmospheric pollutant generated primarily by anthropogenic combustion processes, is typically found at higher concentrations in urban areas compared to non-urbanized environments. Elevated NO2 levels have multiple ecosystem effects at different spatial scales. At the local scale, elevated levels affect human health directly and through the formation of secondary pollutants such as ozone and aerosols; at the regional scale secondary pollutants such as nitric acid and organic nitrates have deleterious effects on non-urbanized areas; and, at the global scale, nitrogen oxide emissions significantly alter the natural biogeochemical nitrogen cycle. As cities globally become larger and larger sources of nitrogen oxide emissions, it is important to assess possible mitigation strategies to reduce the impact of emissions locally, regionally and globally. In this study, we build a national land-use regression (LUR) model to compare the impacts of deciduous and evergreen trees on urban NO2 levels in the United States. We use the EPA monitoring network values of NO2 levels for 2006, the 2006 NLCD tree canopy data for deciduous and evergreen canopies, and the US Census Bureau's TIGER shapefiles for roads, railroads, impervious area & population density as proxies for NO2 sources on-road traffic, railroad traffic, off-road and area sources respectively. Our preliminary LUR model corroborates previous LUR studies showing that the presence of trees is associated with reduced urban NO2 levels. Additionally, our model indicates that deciduous and evergreen trees reduce NO2 to different extents, and that the amount of NO2 reduced varies seasonally. The model indicates that every square kilometer of deciduous canopy within a 2km buffer is associated with a reduction in ambient NO2 levels of 0.64 ppb in summer and 0.46ppb in winter. Similarly, every square kilometer of evergreen tree canopy within a 2 km buffer is associated with a reduction in ambient NO2 by 0.53 ppb in summer and 0.84 ppb in winter. Thus, the model indicates that deciduous trees are associated with a 30% smaller reduction in NO2 in winter as compared to summer, while evergreens are associated with a 60% increase in the reduction of NO2 in winter, for every square kilometer of deciduous or evergreen canopy within a 2 km buffer. Leaf- and local canopy-level studies have shown that trees are a sink for urban NO2 through deposition as well as stomatal and cuticular uptake. The winter time versus summer time effects suggest that leaf-level deposition may not be the only uptake mechanism and points to the need for a more holistic analysis of tree and canopy-level deposition for urban air pollution models. Since deposition velocities for NO2 vary by tree species, the reduction may also vary by species. These findings have implications for designing cities to reduce the impact of air pollution.

Impact of Land Use/Land Cover Conditions on WRF Model Evaluation for Heat Island Assessment

NASA Astrophysics Data System (ADS)

Bhati, S.; Mohan, M.

2017-12-01

Urban heat island effect has been assessed using Weather Research and Forecasting model (WRF v3.5) focusing on air temperature and surface skin temperature in the sub-tropical urban Indian megacity of Delhi. Impact of urbanization related changes in land use/land cover (LULC) on model outputs has been analyzed. Four simulations have been carried out with different types of LULC data viz. (1) USGS , (2) MODIS, (3) user-modified USGS and (4) user modified land use data coupled with urban canopy model (UCM) for incorporation of canopy features. Heat island intensities have been estimated based on these simulations and subsequently compared with those derived from in-situ and satellite observations. There is a significant improvement in model performance with modification of LULC and inclusion of UCM. Overall, RMSEs for near surface temperature improved from 6.3°C to 3.9°C and index of agreement for mean urban heat island intensities (UHI) improved from 0.4 to 0.7 with modified land use coupled with UCM. In general, model is able to capture the magnitude of UHI as well as high UHI zones well. The study highlights the importance of appropriate and updated representation of landuse-landcover and urban canopies for improving predictive capabilities of the mesoscale models.

Evaluating radiative transfer schemes treatment of vegetation canopy architecture in land surface models

NASA Astrophysics Data System (ADS)

Braghiere, Renato; Quaife, Tristan; Black, Emily

2016-04-01

Incoming shortwave radiation is the primary source of energy driving the majority of the Earth's climate system. The partitioning of shortwave radiation by vegetation into absorbed, reflected, and transmitted terms is important for most of biogeophysical processes, including leaf temperature changes and photosynthesis, and it is currently calculated by most of land surface schemes (LSS) of climate and/or numerical weather prediction models. The most commonly used radiative transfer scheme in LSS is the two-stream approximation, however it does not explicitly account for vegetation architectural effects on shortwave radiation partitioning. Detailed three-dimensional (3D) canopy radiative transfer schemes have been developed, but they are too computationally expensive to address large-scale related studies over long time periods. Using a straightforward one-dimensional (1D) parameterisation proposed by Pinty et al. (2006), we modified a two-stream radiative transfer scheme by including a simple function of Sun zenith angle, so-called "structure factor", which does not require an explicit description and understanding of the complex phenomena arising from the presence of vegetation heterogeneous architecture, and it guarantees accurate simulations of the radiative balance consistently with 3D representations. In order to evaluate the ability of the proposed parameterisation in accurately represent the radiative balance of more complex 3D schemes, a comparison between the modified two-stream approximation with the "structure factor" parameterisation and state-of-art 3D radiative transfer schemes was conducted, following a set of virtual scenarios described in the RAMI4PILPS experiment. These experiments have been evaluating the radiative balance of several models under perfectly controlled conditions in order to eliminate uncertainties arising from an incomplete or erroneous knowledge of the structural, spectral and illumination related canopy characteristics typical of model comparisons with in-situ observations. The structure factor parameters were obtained for each canopy structure through the inversion against direct and diffuse fraction of absorbed photosynthetically active radiation (fAPAR), and albedo PAR. Overall, the modified two-stream approximation consistently showed a good agreement with the RAMI4PILPS reference values under direct and diffuse illumination conditions. It is an efficient and accurate tool to derive PAR absorptance and reflectance for scenarios with different canopy densities, leaf densities and soil background albedos, with especial attention to brighter backgrounds, i.e., snowy. The major difficulty of its applicability in the real world is to acquire the parameterisation parameters from in-situ observations. The derivation of parameters from Digital Hemispherical Photographs (DHP) is highly promising at forest stands scales. DHP provide a permanent record and are a valuable information source for position, size, density, and distribution of canopy gaps. The modified two-stream approximation parameters were derived from gap probability data extracted from DHP obtained in a woody savannah in California, USA. Values of fAPAR and albedo PAR were evaluated against a tree-based vegetation canopy model, MAESPA, which used airborne LiDAR data to define the individual-tree locations, and extract structural information such as tree height and crown diameter. The parameterisation improved the performance of a two-stream approximation by making it achieves comparable results to complex 3D model calculations under observed conditions.

Canopy carbon net assimilation of an urban, naturally assembled brownfield forest

NASA Astrophysics Data System (ADS)

Schafer, K. V.; Wadhwa, S.; Tripathee, R.; Gallagher, F. J.

2010-12-01

In this study, we have been investigating an urban brownfield at Liberty State Park that has been abandoned approximately for 40 years. Natural colonization has taken place that allowed a pioneer forest to grow with primarily Betula populifera and Populus spec. Despite soil metal contamination this urban forest exhibits moderate annual productivity and serves as a carbon sink. Diameters at breast height (DBH, 1.35 m above ground) of all trees in a study plot were measured. Aboveground biomass equations were determined for both species through destructive sampling. Aboveground net primary production was about 770 gC m-2 a-1 in 2009. Canopy net assimilation (AnC) was modeled with the canopy conductance constrained assimilation (4CA) model using measured sapflux derived conductance and photosynthetic parameters measured with a LICOR 6400. Annual AnC in 2009 was approximately 1500 gC m-2 a-1 thus with a partitioning of biomass and respiration in the same range of most natural forest with less anthropogenic induced stress. Urban brownfields thus can serve as C sinks and provide phytostabilization of contaminants.

A soil-canopy scheme for use in a numerical model of the atmosphere: 1D stand-alone model

NASA Astrophysics Data System (ADS)

Kowalczyk, E. A.; Garratt, J. R.; Krummel, P. B.

We provide a detailed description of a soil-canopy scheme for use in the CSIRO general circulation models (GCMs) (CSIRO-4 and CSIRO-9), in the form of a one-dimensional stand-alone model. In addition, the paper documents the model's ability to simulate realistic surface fluxes by comparison with mesoscale model simulations (involving more sophisticated soil and boundary-layer treatments) and observations, and the diurnal range in surface quantities, including extreme maximum surface temperatures. The sensitivity of the model to values of the surface resistance is also quantified. The model represents phase 1 of a longer-term plan to improve the atmospheric boundary layer (ABL) and surface schemes in the CSIRO GCMs.

Simulations of the Montréal urban heat island

NASA Astrophysics Data System (ADS)

Roberge, François; Sushama, Laxmi; Fanta, Gemechu

2017-04-01

The current population of Montreal is around 3.8 million and this number is projected to go up in the coming years to decades, which will lead to vast expansion of urban areas. It is well known that urban morphology impacts weather and climate, and therefore should be taken into consideration in urban planning. This is particularly important in the context of a changing climate, as the intensity and frequency of temperature extremes such as hot spells are projected to increase in future climate, and Urban Heat Island (UHI) can potentially raise already stressful temperatures during such events, which can have significant effects on human health and energy consumption. High-resolution regional climate model simulations can be utilized to understand better urban-weather/climate interactions in current and future climates, particularly the spatio-temporal characteristics of the Urban Heat Island and its impact on other weather/climate characteristics such as urban flows, precipitation etc. This paper will focus on two high-resolution (250 m) simulations performed with (1) the Canadian Land Surface Scheme (CLASS) and (2) CLASS and TEB (Town Energy Balance) model; TEB is a single layer urban canopy model and is used to model the urban fractions. The two simulations are performed over a domain covering Montreal for the 1960-2015 period, driven by atmospheric forcing data coming from a high-resolution Canadian Regional Climate Model (CRCM5) simulation, driven by ERA-Interim. The two simulations are compared to assess the impact of urban regions on selected surface fields and the simulation with both CLASS and TEB is then used to study the spatio-temporal characteristics of the UHI over the study domain. Some preliminary results from a coupled simulation, i.e. CRCM5+CLASS+TEB, for selected years, including extreme warm years, will also be presented.

The influence of tree traits and storm event characteristics on stemflow production from isolated deciduous trees in an urban park

NASA Astrophysics Data System (ADS)

Carlyle-Moses, D. E.; Schooling, J. T.

2014-12-01

Urban tree canopy processes affect the volume and biogeochemistry of inputs to the hydrological cycle in cities. We studied stemflow from 37 isolated deciduous trees in an urban park in Kamloops, British Columbia which has a semi-arid climate dominated by small precipitation events. Precipitation and stemflow were measured on an event basis from June 12, 2012 to November 3, 2013. To clarify the effect of canopy traits on stemflow thresholds, rates, yields, percent, and funneling ratios, we analyzed branch angles, bark roughness, tree size, cover, leaf size, and branch and leader counts. High branch angles promoted stemflow in all trees, while bark roughness influenced stemflow differently for single- and multi-leader trees. The association between stemflow and numerous leaders deserves further study. Columnar-form trees often partitioned a large percentage of precipitation into stemflow, with event-scale values as high as 27.9 % recorded for an Armstrong Freeman Maple (Acer x freemanii 'Armstrong'). Under growing-season conditions funneling ratios as high as 196.9 were derived for an American Beech (Fagus grandifolia) individual. Among meteorological variables, rain depth was strongly correlated with stemflow yields; intra-storm break duration, rainfall intensity, rainfall inclination, wind speed, and vapour pressure deficit also played roles. Greater stemflow was associated with leafless canopies and with rain or mixed events versus snow. Results can inform climate-sensitive selection and siting of urban trees towards integrated rainwater management. For example, previous studies suggest that the reduction in storm-water generation by urban trees is accomplished through canopy interception loss alone. However, trees that partition large quantities of precipitation canopy-drainage as stemflow to the base of their trunks, where it has the potential to infiltrate into the soil media rather than fall on impervious surfaces as throughfall, may assist in reducing stormwater flow.

Edge-to-Stem Variability in Wet-Canopy Evaporation From an Urban Tree Row

NASA Astrophysics Data System (ADS)

Van Stan, John T.; Norman, Zachary; Meghoo, Adrian; Friesen, Jan; Hildebrandt, Anke; Côté, Jean-François; Underwood, S. Jeffrey; Maldonado, Gustavo

2017-11-01

Evaporation from wet-canopy (E_C) and stem (E_S) surfaces during rainfall represents a significant portion of municipal-to-global scale hydrologic cycles. For urban ecosystems, E_C and E_S dynamics play valuable roles in stormwater management. Despite this, canopy-interception loss studies typically ignore crown-scale variability in E_C and assume (with few indirect data) that E_S is generally {<}2% of total wet-canopy evaporation. We test these common assumptions for the first time with a spatially-distributed network of in-canopy meteorological monitoring and 45 surface temperature sensors in an urban Pinus elliottii tree row to estimate E_C and E_S under the assumption that crown surfaces behave as "wet bulbs". From December 2015 through July 2016, 33 saturated crown periods (195 h of 5-min observations) were isolated from storms for determination of 5-min evaporation rates ranging from negligible to 0.67 mm h^{-1}. Mean E_S (0.10 mm h^{-1}) was significantly lower (p < 0.01) than mean E_C (0.16 mm h^{-1}). But, E_S values often equalled E_C and, when scaled to trunk area using terrestrial lidar, accounted for 8-13% (inter-quartile range) of total wet-crown evaporation (E_S+E_C scaled to surface area). E_S contributions to total wet-crown evaporation maximized at 33%, showing a general underestimate (by 2-17 times) of this quantity in the literature. Moreover, results suggest wet-crown evaporation from urban tree rows can be adequately estimated by simply assuming saturated tree surfaces behave as wet bulbs, avoiding problematic assumptions associated with other physically-based methods.

On the Pollutant Plume Dispersion in the Urban Canopy Layer over 2D Idealized Street Canyons: A Large-Eddy Simulation Approach

NASA Astrophysics Data System (ADS)

Wong, Colman C. C.; Liu, Chun-Ho

2010-05-01

Anthropogenic emissions are the major sources of air pollutants in urban areas. To improve the air quality in dense and mega cities, a simple but reliable prediction method is necessary. In the last five decades, the Gaussian pollutant plume model has been widely used for the estimation of air pollutant distribution in the atmospheric boundary layer (ABL) in an operational manner. Whereas, it was originally designed for rural areas with rather open and flat terrain. The recirculating flows below the urban canopy layer substantially modify the near-ground urban wind environment and so does the pollutant distribution. Though the plume height and dispersion are often adjusted empirically, the accuracy of applying the Gaussian pollutant plume model in urban areas, of which the bottom of the flow domain consists of numerous inhomogeneous buildings, is unclear. To elucidate the flow and pollutant transport, as well as to demystify the uncertainty of employing the Gaussian pollutant plume model over urban roughness, this study was performed to examine how the Gaussian-shape pollutant plume in the urban canopy layer is modified by the idealized two-dimensional (2D) street canyons at the bottom of the ABL. The specific objective is to develop a parameterization so that the geometric effects of urban morphology on the operational pollutant plume dispersion models could be taken into account. Because atmospheric turbulence is the major means of pollutant removal from street canyons to the ABL, the large-eddy simulation (LES) was adopted to calculate explicitly the flows and pollutant transport in the urban canopy layer. The subgrid-scale (SGS) turbulent kinetic energy (TKE) conservation was used to model the SGS processes in the incompressible, isothermal conditions. The computational domain consists of 12 identical idealized street canyons of unity aspect ratio which were placed evenly in the streamwise direction. Periodic boundary conditions (BCs) for the flow were applied in the horizontal and the spanwise directions. The prevalent wind was driven by a background pressure gradient in the roughness sublayer only, no background force was prescribed inside the street canyons. While the periodic BC of pollutant was used in the spanwise direction, zero pollutant and an open BC were applied, respectively, at the inflow and outflow of the streamwise extent to avoid pollutant being reflected back into the computational domain. The ground of the first street canyon was assigned as the pollutant source on which a BC of constant pollutant concentration was prescribed. The LES results showed that, in the neutrally stratified ABL, the pollutant distribution in the urban canopy layer resembled the Gaussian plume shape in general even recirculating flows were observed in the street canyons. The roof-level horizontal profile of pollutant concentration in the streamwise direction showed that the sharp drop on the leeward side of each street canyon was likely caused by the air and pollutant entrainments. On the windward side of each street canyon, a mild increase in pollutant concentration was observed that did not follow the Gaussian plume closely. Those deviations extended to a certain height over the roof level of the street canyons. It in turn suggests that the Gaussian pollutant plume model should be applied with caution in the urban canopy layer in the vicinity over urban roughness. To further analyze the effects of urban roughness on the plume dispersion in detail, a few LES calculations with different aspect ratios are currently being undertaken so as to compare with the current LES results.

Potential impacts of urban land expansion on Asian airborne pollutant outflows

NASA Astrophysics Data System (ADS)

Tao, Wei; Liu, Junfeng; Ban-Weiss, George A.; Zhang, Lin; Zhang, Jiachen; Yi, Kan; Tao, Shu

2017-07-01

Eastern part of China (EPC) has experienced rapid urbanization during the past few decades. Here we investigate the impacts of urban land expansion over EPC on the export of Asian pollutants to the western Pacific during January, April, July, and October of 2009 using the Weather Research and Forecasting model coupled to Chemistry (WRF/Chem) and a single-layer urban canopy scheme. Over urbanizing areas, increases in the urban land fraction result in a linearly enhanced uplift of surface primary pollutants to higher altitudes. We further examine how this local effect would change outflows of Asian pollutants to the western Pacific using the tagged black carbon (BC) and carbon monoxide (CO) tracers emitted from EPC (denoted by BCt and COt, respectively). Overall, a 0.1 increase in the fraction of land area that is urban over EPC would linearly (R2 = 0.70-0.96) increase the mean tropospheric eastward export of BCt and COt across meridional planes (i.e., 135°E and 150°E) by 4-40% and 1-6% in different months, respectively. The relative perturbation in exporting efficiency generally maximizes during July while minimizes during April. The urbanization-export relationship is largely driven by the elevation effect and is also impacted by urbanization-forced changes in zonal winds. The spatial pattern of the response of BCt over the downwind Pacific differs from that of COt mainly due to aerosol-cloud interactions. Our findings demonstrate that extensive urban land expansion could substantially impact climate and air quality from a local scale to a regional scale, especially for shorter-lived air pollutants such as BC and other aerosols.

Observing the Vertical Dimensions of Singapore's Urban Heat Island

NASA Astrophysics Data System (ADS)

Chow, W. T. L.; Ho, D. X. Q.

2015-12-01

In numerous cities, measurements of urban warmth in most urban heat island (UHI) studies are generally constrained towards surface or near-surface (<2 m above ground) levels across horizontal variations in land use and land cover. However, there has been hitherto limited attention towards the measurement of vertical temperature profiles extending from the urban surface through to the urban boundary layer. Knowledge of these profiles, through how they vary over different local urban morphologies, and develop with respect to synoptic meteorological conditions, are important towards several aspects of UHI research; these include validating modelling urban canopy lapse rate profiles or estimating the growth of urban plumes. In this study, we utilised temperature sensors attached onto remote controlled aerial quadcopter platforms to measure urban temperature and humidity profiles in Singapore, which is a rapidly urbanizing major tropical metropolis. These profiles were measured from the surface to ~100 m above ground level, a height which includes all of the urban canopy and parts of the urban boundary layer. Initial results indicate significant variations in stability measured over different land uses (e.g. urban park, high-rise residential, commercial); these profiles are also temporally dynamic, depending on the time of day and larger-scale weather conditions.

Studying urban land-atmospheric interactions by coupling an urban canopy model with a single column atmospheric models

NASA Astrophysics Data System (ADS)

Song, J.; Wang, Z.

2013-12-01

Studying urban land-atmospheric interactions by coupling an urban canopy model with a single column atmospheric models Jiyun Song and Zhi-Hua Wang School of Sustainable Engineering and the Built Environment, Arizona State University, PO Box 875306, Tempe, AZ 85287-5306 Landuse landcover changes in urban area will modify surface energy budgets, turbulent fluxes as well as dynamic and thermodynamic structures of the overlying atmospheric boundary layer (ABL). In order to study urban land-atmospheric interactions, we coupled a single column atmospheric model (SCM) to a cutting-edge single layer urban canopy model (SLUCM). Modification of surface parameters such as the fraction of vegetation and engineered pavements, thermal properties of building and pavement materials, and geometrical features of street canyon, etc. in SLUCM dictates the evolution of surface balance of energy, water and momentum. The land surface states then provide lower boundary conditions to the overlying atmosphere, which in turn modulates the modification of ABL structure as well as vertical profiles of temperature, humidity, wind speed and tracer gases. The coupled SLUCM-SCM model is tested against field measurements of surface layer fluxes as well as profiles of temperature and humidity in the mixed layer under convective conditions. After model test, SLUCM-SCM is used to simulate the effect of changing urban land surface conditions on the evolution of ABL structure and dynamics. Simulation results show that despite the prescribed atmospheric forcing, land surface states impose significant impact on the physics of the overlying vertical atmospheric layer. Overall, this numerical framework provides a useful standalone modeling tool to assess the impacts of urban land surface conditions on the local hydrometeorology through land-atmospheric interactions. It also has potentially far-reaching implications to urban ecohydrological services for cities under future expansion and climate challenges.

CO2 dispersion modelling over Paris region within the CO2-MEGAPARIS project

NASA Astrophysics Data System (ADS)

Lac, C.; Donnelly, R. P.; Masson, V.; Pal, S.; Donier, S.; Queguiner, S.; Tanguy, G.; Ammoura, L.; Xueref-Remy, I.

2012-10-01

Accurate simulation of the spatial and temporal variability of tracer mixing ratios over urban areas is challenging, but essential in order to utilize CO2 measurements in an atmospheric inverse framework to better estimate regional CO2 fluxes. This study investigates the ability of a high-resolution model to simulate meteorological and CO2 fields around Paris agglomeration, during the March field campaign of the CO2-MEGAPARIS project. The mesoscale atmospheric model Meso-NH, running at 2 km horizontal resolution, is coupled with the Town-Energy Balance (TEB) urban canopy scheme and with the Interactions between Soil, Biosphere and Atmosphere CO2-reactive (ISBA-A-gs) surface scheme, allowing a full interaction of CO2 between the surface and the atmosphere. Statistical scores show a good representation of the Urban Heat Island (UHI) and urban-rural contrasts. Boundary layer heights (BLH) at urban, sub-urban and rural sites are well captured, especially the onset time of the BLH increase and its growth rate in the morning, that are essential for tall tower CO2 observatories. Only nocturnal BLH at sub-urban sites are slightly underestimated a few nights, with a bias less than 50 m. At Eiffel tower, the observed spikes of CO2 maxima occur every morning exactly at the time at which the Atmospheric Boundary Layer (ABL) growth reaches the measurement height. The timing of the CO2 cycle is well captured by the model, with only small biases on CO2 concentrations, mainly linked to the misrepresentation of anthropogenic emissions, as the Eiffel site is at the heart of trafic emission sources. At sub-urban ground stations, CO2 measurements exhibit maxima at the beginning and at the end of each night, when the ABL is fully contracted, with a very strong spatio-temporal variability. The CO2 cycle at these sites is generally well reproduced by the model, even if some biases on the nocturnal maxima appear in the Paris plume parly due to small errors on the vertical transport, or in the vicinity of airports due to small errors on the horizontal transport (wind direction). A sensitivity test without urban parameterisation removes UHI and underpredicts nighttime BLH over urban and sub-urban sites, leading to large overestimation of nocturnal CO2 concentration at the sub-urban sites. The agreement of daytime and nighttime BLH and CO2 predictions of the reference simulation over Paris agglomeration demonstrates the potential of using the meso-scale system on urban and sub-urban area in the context of inverse modelling.

Canopy volume removal from oil and gas development activity in the upper Susquehanna River basin in Pennsylvania and New York (USA): An assessment using lidar data

USGS Publications Warehouse

Young, John A.; Maloney, Kelly O.; Slonecker, Terry; Milheim, Lesley E.; Siripoonsup, David

2018-01-01

Oil and gas development is changing the landscape in many regions of the United States and globally. However, the nature, extent, and magnitude of landscape change and development, and precisely how this development compares to other ongoing land conversion (e.g. urban/sub-urban development, timber harvest) is not well understood. In this study, we examine land conversion from oil and gas infrastructure development in the upper Susquehanna River basin in Pennsylvania and New York, an area that has experienced much oil and gas development over the past 10 years. We quantified land conversion in terms of forest canopy geometric volume loss in contrast to previous studies that considered only areal impacts. For the first time in a study of this type, we use fine-scale lidar forest canopy geometric models to assess the volumetric change due to forest clearing from oil and gas development and contrast this land change to clear cut forest harvesting, and urban and suburban development. Results show that oil and gas infrastructure development removed a large volume of forest canopy from 2006 to 2013, and this removal spread over a large portion of the study area. Timber operations (clear cutting) on Pennsylvania State Forest lands removed a larger total volume of forest canopy during the same time period, but this canopy removal was concentrated in a smaller area. Results of our study point to the need to consider volumetric impacts of oil and gas development on ecosystems, and to place potential impacts in context with other ongoing land conversions.

A framework for adapting urban forests to climate change

Treesearch

Leslie Brandt; Abigail Derby Lewis; Robert Fahey; Lydia Scott; Lindsay Darling; Chris Swanston

2016-01-01

Planting urban trees and expanding urban forest canopy cover are often considered key strategies for reducing climate change impacts in urban areas. However, urban trees and forests can also be vulnerable to climate change through shifts in tree habitat suitability, changes in pests and diseases, and changes in extreme weather events. We developed a three-step...

Measurements and Computations of Flow in an Urban Street System

NASA Astrophysics Data System (ADS)

Castro, Ian P.; Xie, Zheng-Tong; Fuka, V.; Robins, Alan G.; Carpentieri, M.; Hayden, P.; Hertwig, D.; Coceal, O.

2017-02-01

We present results from laboratory and computational experiments on the turbulent flow over an array of rectangular blocks modelling a typical, asymmetric urban canopy at various orientations to the approach flow. The work forms part of a larger study on dispersion within such arrays (project DIPLOS) and concentrates on the nature of the mean flow and turbulence fields within the canopy region, recognising that unless the flow field is adequately represented in computational models there is no reason to expect realistic simulations of the nature of the dispersion of pollutants emitted within the canopy. Comparisons between the experimental data and those obtained from both large-eddy simulation (LES) and direct numerical simulation (DNS) are shown and it is concluded that careful use of LES can produce generally excellent agreement with laboratory and DNS results, lending further confidence in the use of LES for such situations. Various crucial issues are discussed and advice offered to both experimentalists and those seeking to compute canopy flows with turbulence resolving models.

The impact of changing the land surface scheme in ACCESS(v1.0/1.1) on the surface climatology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kowalczyk, Eva A.; Stevens, Lauren E.; Law, Rachel M.

The Community Atmosphere Biosphere Land Exchange (CABLE) model has been coupled to the UK Met Office Unified Model (UM) within the existing framework of the Australian Community Climate and Earth System Simulator (ACCESS), replacing the Met Office Surface Exchange Scheme (MOSES). Here we investigate how features of the CABLE model impact on present-day surface climate using ACCESS atmosphere-only simulations. The main differences attributed to CABLE include a warmer winter and a cooler summer in the Northern Hemisphere (NH), earlier NH spring runoff from snowmelt, and smaller seasonal and diurnal temperature ranges. The cooler NH summer temperatures in canopy-covered regions aremore » more consistent with observations and are attributed to two factors. Firstly, CABLE accounts for aerodynamic and radiative interactions between the canopy and the ground below; this placement of the canopy above the ground eliminates the need for a separate bare ground tile in canopy-covered areas. Secondly, CABLE simulates larger evapotranspiration fluxes and a slightly larger daytime cloud cover fraction. Warmer NH winter temperatures result from the parameterization of cold climate processes in CABLE in snow-covered areas. In particular, prognostic snow density increases through the winter and lowers the diurnally resolved snow albedo; variable snow thermal conductivity prevents early winter heat loss but allows more heat to enter the ground as the snow season progresses; liquid precipitation freezing within the snowpack delays the building of the snowpack in autumn and accelerates snow melting in spring. Altogether we find that the ACCESS simulation of surface air temperature benefits from the specific representation of the turbulent transport within and just above the canopy in the roughness sublayer as well as the more complex snow scheme in CABLE relative to MOSES.« less

The impact of changing the land surface scheme in ACCESS(v1.0/1.1) on the surface climatology

DOE PAGES

Kowalczyk, Eva A.; Stevens, Lauren E.; Law, Rachel M.; ...

2016-08-23

The Community Atmosphere Biosphere Land Exchange (CABLE) model has been coupled to the UK Met Office Unified Model (UM) within the existing framework of the Australian Community Climate and Earth System Simulator (ACCESS), replacing the Met Office Surface Exchange Scheme (MOSES). Here we investigate how features of the CABLE model impact on present-day surface climate using ACCESS atmosphere-only simulations. The main differences attributed to CABLE include a warmer winter and a cooler summer in the Northern Hemisphere (NH), earlier NH spring runoff from snowmelt, and smaller seasonal and diurnal temperature ranges. The cooler NH summer temperatures in canopy-covered regions aremore » more consistent with observations and are attributed to two factors. Firstly, CABLE accounts for aerodynamic and radiative interactions between the canopy and the ground below; this placement of the canopy above the ground eliminates the need for a separate bare ground tile in canopy-covered areas. Secondly, CABLE simulates larger evapotranspiration fluxes and a slightly larger daytime cloud cover fraction. Warmer NH winter temperatures result from the parameterization of cold climate processes in CABLE in snow-covered areas. In particular, prognostic snow density increases through the winter and lowers the diurnally resolved snow albedo; variable snow thermal conductivity prevents early winter heat loss but allows more heat to enter the ground as the snow season progresses; liquid precipitation freezing within the snowpack delays the building of the snowpack in autumn and accelerates snow melting in spring. Altogether we find that the ACCESS simulation of surface air temperature benefits from the specific representation of the turbulent transport within and just above the canopy in the roughness sublayer as well as the more complex snow scheme in CABLE relative to MOSES.« less

Differential Impact of Passive versus Active Irrigation on Urban Forests in Semiarid Regions

NASA Astrophysics Data System (ADS)

Luketich, A. M.; Papuga, S. A.; Crimmins, M.

2017-12-01

The network of trees within a city provides a variety of ecosystem services such as flood mitigation and reduced heat island effects. To maintain these `urban forests' in semiarid cities, the use of scarce water resources for irrigation is often necessary. Rainwater harvesting has been widely adopted in Tucson, AZ as a sustainable water source for trees, but the effects of passive water harvesting versus active irrigation on tree canopy productivity and microclimate is largely unquantified. We hypothesize that regardless of whether trees are passively or actively irrigated, deep soil moisture will be elevated compared to natural conditions; however, we expect that increased deep soil moisture conditions will be more frequent using active irrigation. Additionally, we hypothesize that similar to natural settings, urban trees will need access deep soil moisture for transpiration. Therefore, we expect that actively irrigated trees will have more periods of transpiration than passively irrigated trees and that this will result in elevated and sustained phenological activity. We also expect that this difference will translate to more ecosystem services for a longer portion of the year in actively irrigated urban forests. Here, we compare key ecohydrological indicators of passive and active irrigation systems at two sites in Tucson, AZ. Our measurements include soil moisture, transpiration, air temperature, soil temperature, below- and within- canopy temperatures, and canopy phenology. Our first year of results suggest there are differences in transpiration, canopy greening and microclimate between the two irrigation techniques and that the magnitude of these differences are highly seasonal. This research can help to improve understanding of the practices and function of green infrastructure in semiarid cities and inform models that attempt to aggregate the influence of these urban forests for understanding watershed management strategies.

Land use and urban morphology parameters for Vienna required for initialisation of the urban canopy model TEB derived via the concept of "local climate zones"

NASA Astrophysics Data System (ADS)

Trimmel, Heidelinde; Weihs, Philipp; Oswald, Sandro M.; Masson, Valéry; Schoetter, Robert

2017-04-01

Urban settlements are generally known for their high fractions of impermeable surfaces, large heat capacity and low humidity compared to rural areas which results in the well known phenomena of urban heat islands. The urbanized areas are growing which can amplify the intensity and frequency of situations with heat stress. The distribution of the urban heat island is not uniform though, because the urban environment is highly diverse regarding its morphology as building heights, building contiguity and configuration of open spaces and trees vary, which cause changes in the aerodynamic resistance for heat transfers and drag coefficients for momentum. Furthermore cities are characterized by highly variable physical surface properties as albedo, emissivity, heat capacity and thermal conductivity. The distribution of the urban heat island is influenced by these morphological and physical parameters as well as the distribution of unsealed soil and vegetation. These aspects influence the urban climate on micro- and mesoscale. For larger Vienna high resolution vector and raster geodatasets were processed to derive land use surface fractions and building morphology parameters on block scale following the methodology of Cordeau (2016). A dataset of building age and typology was cross checked and extended using satellite visual and thermal bands and linked to a database joining building age and typology with typical physical building parameters obtained from different studies (Berger et al. 2012 and Amtmann M and Altmann-Mavaddat N (2014)) and the OIB (Österreichisches Institut für Bautechnik). Using dominant parameters obtained using this high resolution mainly ground based data sets (building height, built area fraction, unsealed fraction, sky view factor) a local climate zone classification was produced using an algorithm. The threshold values were chosen according to Stewart and Oke (2012). This approach is compared to results obtained with the methodology of Bechtel et al. (2015) which is based on machine learning algorithms depending on satellite imagery and expert knowledge. The data on urban land use and morphology are used for initialisation of the town energy balance scheme TEB, but are also useful for other urban canopy models or studies related to urban planning or modelling of the urban system. The sensitivity of canyon air and surface temperatures, air specific humidity and horizontal wind simulated by the town energy balance scheme TEB (Masson, 2000) regarding the dominant parameters within the range determined for the present urban structure of Vienna and the expected changes (MA 18 (2011, 2014a+b), PGO (2011), Amtmann M and Altmann-Mavaddat N (2014)) was calculated for different land cover zones. While the buildings heights have a standard deviation of 3.2m which is 15% of the maximum average building height of one block the built and unsealed surface fraction vary stronger with around 30% standard deviation. The pre 1919 structure of Vienna is rather uniform and easier to describe, the later building structure is more diverse regarding morphological as well as physical building parameters. Therefore largest uncertainties are possible at the urban rims where also the highest development is expected. The analysis will be focused on these areas. Amtmann M and Altmann-Mavaddat N (2014) Eine Typology österreichischer Wohngebäude, Österreichische Energieargentur - Austrian Energy Agency, TABULA/EPISCOPE Bechtel B, Alexander P, Böhner J, et al (2015) Mapping Local Climate Zones for a Worldwide Database of the Form and Function of Cities. ISPRS Int J Geo-Inf 4:199-219. doi: 10.3390/ijgi4010199 Berger T, Formayer H, Smutny R, Neururer C, Passawa R (2012) Auswirkungen des Klimawandelsauf den thermischen Komfort in Bürogebäuden, Berichte aus Energie- und Umweltforschung Cordeau E / Les îlots morphologiques urbains (IMU) / IAU îdF / 2016 Magistratsabteilung 18 - Stadtentwicklung und Stadtplanung, Wien - MA 18 (2011) Siedlungsformen für die Stadterweiterung, MA 18 (2014a) Smart City Wien - Rahmenstrategie MA 18 (2014b) Stadtentwicklungsplan STEP 2025, www.step.wien.at Masson V (2000) A physically-based scheme for the urban energy budget in atmospheric models. Bound-Layer Meteorol 94:357-397. doi: 10.1023/A:1002463829265 PGO (Planungsgemeinschaft Ost) (2011) stadtregion +, Planungskooperation zur räumlichen Entwicklung der Stadtregion Wien Niederösterreich Burgenland. Stewart ID, Oke TR (2012) Local climate zones for urban temperature studies. Bull Am Meteorol Soc 93:1879-1900.

i-Tree: Tools to assess and manage structure, function, and value of community forests

NASA Astrophysics Data System (ADS)

Hirabayashi, S.; Nowak, D.; Endreny, T. A.; Kroll, C.; Maco, S.

2011-12-01

Trees in urban communities can mitigate many adverse effects associated with anthropogenic activities and climate change (e.g. urban heat island, greenhouse gas, air pollution, and floods). To protect environmental and human health, managers need to make informed decisions regarding urban forest management practices. Here we present the i-Tree suite of software tools (www.itreetools.org) developed by the USDA Forest Service and their cooperators. This software suite can help urban forest managers assess and manage the structure, function, and value of urban tree populations regardless of community size or technical capacity. i-Tree is a state-of-the-art, peer-reviewed Windows GUI- or Web-based software that is freely available, supported, and continuously refined by the USDA Forest Service and their cooperators. Two major features of i-Tree are 1) to analyze current canopy structures and identify potential planting spots, and 2) to estimate the environmental benefits provided by the trees, such as carbon storage and sequestration, energy conservation, air pollution removal, and storm water reduction. To cover diverse forest topologies, various tools were developed within the i-Tree suite: i-Tree Design for points (individual trees), i-Tree Streets for lines (street trees), and i-Tree Eco, Vue, and Canopy (in the order of complexity) for areas (community trees). Once the forest structure is identified with these tools, ecosystem services provided by trees can be estimated with common models and protocols, and reports in the form of texts, charts, and figures are then created for users. Since i-Tree was developed with a client/server architecture, nationwide data in the US such as location-related parameters, weather, streamflow, and air pollution data are stored in the server and retrieved to a user's computer at run-time. Freely available remote-sensed images (e.g. NLCD and Google maps) are also employed to estimate tree canopy characteristics. As the demand for i-Tree grows internationally, environmental databases from more countries will be coupled with the software suite. Two more i-Tree applications, i-Tree Forecast and i-Tree Landscape are now under development. i-Tree Forecast simulates canopy structures for up to 100 years based on planting and mortality rates and adds capabilities for other i-Tree applications to estimate the benefits of future canopy scenarios. While most i-Tree applications employ a spatially lumped approach, i-Tree landscape employs a spatially distributed approach that allows users to map changes in canopy cover and ecosystem services through time and space. These new i-Tree tools provide an advanced platform for urban managers to assess the impact of current and future urban forests. i-Tree allows managers to promote effective urban forest management and sound arboricultural practices by providing information for advocacy and planning, baseline data for making informed decisions, and standardization for comparisons with other communities.

Development of Gridded Fields of Urban Canopy Parameters for Advanced Urban Meteorological and Air Quality Models

EPA Science Inventory

Urban dispersion and air quality simulation models applied at various horizontal scales require different levels of fidelity for specifying the characteristics of the underlying surfaces. As the modeling scales approach the neighborhood level (~1 km horizontal grid spacing), the...

Homeowner interactions with residential trees in urban areas

Treesearch

Jana Dilley; Kathleen L. Wolf

2013-01-01

Urban forests are a critical element in sustainable urban areas because of the many environmental, economic, and social benefits that city trees provide. In order to increase canopy cover in urban areas, residential homeowners, who collectively own the majority of the land in most cities, need to engage in planting and retaining trees on their properties. This...

A specific PFT and sub-canopy structure for simulating oil palm in the Community Land Model

NASA Astrophysics Data System (ADS)

Fan, Y.; Knohl, A.; Roupsard, O.; Bernoux, M.; LE Maire, G.; Panferov, O.; Kotowska, M.; Meijide, A.

2015-12-01

Towards an effort to quantify the effects of rainforests to oil palm conversion on land-atmosphere carbon, water and energy fluxes, a specific plant functional type (PFT) and sub-canopy structure are developed for simulating oil palm within the Community Land Model (CLM4.5). Current global land surface models only simulate annual crops beside natural vegetation. In this study, a multilayer oil palm subroutine is developed in CLM4.5 for simulating oil palm's phenology and carbon and nitrogen allocation. The oil palm has monopodial morphology and sequential phenology of around 40 stacked phytomers, each carrying a large leaf and a fruit bunch, forming a natural multilayer canopy. A sub-canopy phenological and physiological parameterization is thus introduced, so that multiple phytomer components develop simultaneously but according to their different phenological steps (growth, yield and senescence) at different canopy layers. This specific multilayer structure was proved useful for simulating canopy development in terms of leaf area index (LAI) and fruit yield in terms of carbon and nitrogen outputs in Jambi, Sumatra (Fan et al. 2015). The study supports that species-specific traits, such as palm's monopodial morphology and sequential phenology, are necessary representations in terrestrial biosphere models in order to accurately simulate vegetation dynamics and feedbacks to climate. Further, oil palm's multilayer structure allows adding all canopy-level calculations of radiation, photosynthesis, stomatal conductance and respiration, beside phenology, also to the sub-canopy level, so as to eliminate scale mismatch problem among different processes. A series of adaptations are made to the CLM model. Initial results show that the adapted multilayer radiative transfer scheme and the explicit represention of oil palm's canopy structure improve on simulating photosynthesis-light response curve. The explicit photosynthesis and dynamic leaf nitrogen calculations per canopy layer also enhance simulated CO2 flux when compared to eddy covariance flux data. More investigations on energy and water fluxes and nitrogen balance are being conducted. These new schemes would hopefully promote the understanding of climatic effects of the tropical land use transformation system.

Bayes classification of interferometric TOPSAR data

NASA Technical Reports Server (NTRS)

Michel, T. R.; Rodriguez, E.; Houshmand, B.; Carande, R.

1995-01-01

We report the Bayes classification of terrain types at different sites using airborne interferometric synthetic aperture radar (INSAR) data. A Gaussian maximum likelihood classifier was applied on multidimensional observations derived from the SAR intensity, the terrain elevation model, and the magnitude of the interferometric correlation. Training sets for forested, urban, agricultural, or bare areas were obtained either by selecting samples with known ground truth, or by k-means clustering of random sets of samples uniformly distributed across all sites, and subsequent assignments of these clusters using ground truth. The accuracy of the classifier was used to optimize the discriminating efficiency of the set of features that was chosen. The most important features include the SAR intensity, a canopy penetration depth model, and the terrain slope. We demonstrate the classifier's performance across sites using a unique set of training classes for the four main terrain categories. The scenes examined include San Francisco (CA) (predominantly urban and water), Mount Adams (WA) (forested with clear cuts), Pasadena (CA) (urban with mountains), and Antioch Hills (CA) (water, swamps, fields). Issues related to the effects of image calibration and the robustness of the classification to calibration errors are explored. The relative performance of single polarization Interferometric data classification is contrasted against classification schemes based on polarimetric SAR data.

Human and biophysical legacies shape contemporary urban forests: A literature synthesis

Treesearch

Lara A. Roman; Hamil Pearsall; Theodore S. Eisenman; Tenley M. Conway; Robert T. Fahey; Shawn Landry; Jess Vogt; Natalie S. van Doorn; J. Morgan Grove; Dexter H. Locke; Adrina C. Bardekjian; John J. Battles; Mary L. Cadenasso; Cecil C. Konijnendijk van den Bosch; Meghan Avolio; Adam Berland; G. Darrel Jenerette; Sarah K. Mincey; Diane E. Pataki; Christina Staudhammer

2018-01-01

Understanding how urban forests developed their current patterns of tree canopy cover, species composition, and diversity requires an appreciation of historical legacy effects. However, analyses of current urban forest characteristics are often limited to contemporary socioeconomic factors, overlooking the role of history. The institutions, human communities, and...

Automatic extraction of tree crowns from aerial imagery in urban environment

NASA Astrophysics Data System (ADS)

Liu, Jiahang; Li, Deren; Qin, Xunwen; Yang, Jianfeng

2006-10-01

Traditionally, field-based investigation is the main method to investigate greenbelt in urban environment, which is costly and low updating frequency. In higher resolution image, the imagery structure and texture of tree canopy has great similarity in statistics despite the great difference in configurations of tree canopy, and their surface structures and textures of tree crown are very different from the other types. In this paper, we present an automatic method to detect tree crowns using high resolution image in urban environment without any apriori knowledge. Our method catches unique structure and texture of tree crown surface, use variance and mathematical expectation of defined image window to position the candidate canopy blocks coarsely, then analysis their inner structure and texture to refine these candidate blocks. The possible spans of all the feature parameters used in our method automatically generate from the small number of samples, and HOLE and its distribution as an important characteristics are introduced into refining processing. Also the isotropy of candidate image block and holes' distribution is integrated in our method. After introduction the theory of our method, aerial imageries were used ( with a resolution about 0.3m ) to test our method, and the results indicate that our method is an effective approach to automatically detect tree crown in urban environment.

Modeling the Urban Boundary and Canopy Layers

EPA Science Inventory

Today, we are confronted with increasingly more sophisticated application requirements for urban modeling. These include those that address emergency response to acute exposures from toxic releases, health exposure assessments from adverse air quality, energy usage, and character...

SIRANERISK: Modelling dispersion of steady and unsteady pollutant releases in the urban canopy

NASA Astrophysics Data System (ADS)

Soulhac, L.; Lamaison, G.; Cierco, F.-X.; Ben Salem, N.; Salizzoni, P.; Mejean, P.; Armand, P.; Patryl, L.

2016-09-01

SIRANERISK is an operational model for the simulation of the dispersion of unsteady atmospheric releases of pollutant within and above an urban area. SIRANERISK is built on the same principles as the SIRANE model, and couples a street network model for the pollutant transfers within the urban canopy with a Gaussian puff model for the transfers above it. The performance of the model are here analysed by a detailed comparisons with wind-tunnel experiments. These experiments concern the dispersion of steady and unsteady pollutant releases within and above obstacle arrays with varying geometrical configurations, representing different topologies of idealised urban districts. The overall good agreement between numerical and experimental data demonstrates the reliability of SIRANERISK as an operational tool for the assessment of risk analysis and for the management of crises due to the accidental release of harmful airborne pollutants within a built environment.

Assessing the US Urban Forest Resources

Treesearch

David J. Nowak; Mary H. Noble; Susan M. Sisinni; John F. Dwyer

2001-01-01

Urban areas in the conterminous United States doubled in size between 1969 and 1994, and currently cover 3.5 percent of the total land area and contain more than 75 percent of the US population. Urban areas contain approximately 3.8 billion trees with an average tree canopy cover of 27 percent. The extent and variation of urban forests across the 48 states are explored...

CO2 dispersion modelling over Paris region within the CO2-MEGAPARIS project

NASA Astrophysics Data System (ADS)

Lac, C.; Donnelly, R. P.; Masson, V.; Pal, S.; Riette, S.; Donier, S.; Queguiner, S.; Tanguy, G.; Ammoura, L.; Xueref-Remy, I.

2013-05-01

Accurate simulation of the spatial and temporal variability of tracer mixing ratios over urban areas is a challenging and interesting task needed to be performed in order to utilise CO2 measurements in an atmospheric inverse framework and to better estimate regional CO2 fluxes. This study investigates the ability of a high-resolution model to simulate meteorological and CO2 fields around Paris agglomeration during the March field campaign of the CO2-MEGAPARIS project. The mesoscale atmospheric model Meso-NH, running at 2 km horizontal resolution, is coupled with the Town Energy Balance (TEB) urban canopy scheme and with the Interactions between Soil, Biosphere and Atmosphere CO2-reactive (ISBA-A-gs) surface scheme, allowing a full interaction of CO2 modelling between the surface and the atmosphere. Statistical scores show a good representation of the urban heat island (UHI) with stronger urban-rural contrasts on temperature at night than during the day by up to 7 °C. Boundary layer heights (BLH) have been evaluated on urban, suburban and rural sites during the campaign, and also on a suburban site over 1 yr. The diurnal cycles of the BLH are well captured, especially the onset time of the BLH increase and its growth rate in the morning, which are essential for tall tower CO2 observatories. The main discrepancy is a small negative bias over urban and suburban sites during nighttime (respectively 45 m and 5 m), leading to a few overestimations of nocturnal CO2 mixing ratios at suburban sites and a bias of +5 ppm. The diurnal CO2 cycle is generally well captured for all the sites. At the Eiffel tower, the observed spikes of CO2 maxima occur every morning exactly at the time at which the atmospheric boundary layer (ABL) growth reaches the measurement height. At suburban ground stations, CO2 measurements exhibit maxima at the beginning and at the end of each night, when the ABL is fully contracted, with a strong spatio-temporal variability. A sensitivity test without urban parameterisation removes the UHI and underpredicts nighttime BLH over urban and suburban sites, leading to large overestimation of nocturnal CO2 mixing ratio at the suburban sites (bias of +17 ppm). The agreement between observation and prediction for BLH and CO2 concentrations and urban-rural increments, both day and night, demonstrates the potential of using the urban mesoscale system in the context of inverse modelling

The Impacts of Urbanization on Meteorology and Air Quality in the Los Angeles Basin

NASA Astrophysics Data System (ADS)

Li, Y.; Zhang, J.; Sailor, D.; Ban-Weiss, G. A.

2017-12-01

Urbanization has a profound influence on regional meteorology in mega cities like Los Angeles. This influence is driven by changes in land surface physical properties and urban processes, and their corresponding influence on surface-atmosphere coupling. Changes in meteorology from urbanization in turn influences air quality through weather-dependent chemical reaction, pollutant dispersion, etc. Hence, a real-world representation of the urban land surface properties and urban processes should be accurately resolved in regional climate-chemistry models for better understanding the role of urbanization on changing urban meteorology and associated pollutant dynamics. By incorporating high-resolution land surface data, previous research has improved model-observation comparisons of meteorology in urban areas including the Los Angeles basin, and indicated that historical urbanization has increased urban temperatures and altered wind flows significantly. However, the impact of urban expansion on air quality has been less studied. Thus, in this study, we aim to evaluate the effectiveness of resolving high-resolution heterogeneity in urban land surface properties and processes for regional weather and pollutant concentration predictions. We coupled the Weather Research and Forecasting model with Chemistry to the single-layer Urban Canopy Model to simulate a typical summer period in year 2012 for Southern California. Land cover type and urban fraction were determined from National Land Cover Data. MODIS observations were used to determine satellite-derived albedo, green vegetation fraction, and leaf area index. Urban morphology was determined from GIS datasets of 3D building geometries. An urban irrigation scheme was also implemented in the model. Our results show that the improved model captures the diurnal cycle of 2m air temperature (T2) and Ozone (O3) concentrations. However, it tends to overestimate wind speed and underestimate T2, which leads to an underestimation of O3 and fine particulate matter concentrations. By comparing simulations assuming current land cover of the Los Angeles basin versus pre-urbanization land cover, we find that land cover change through urbanization has led to important shifts in regional air pollution via the aforementioned physical and chemical mechanisms.

How many trees are enough? Tree death and the urban canopy

Treesearch

Lara A. Roman

2014-01-01

Massive city tree planting campaigns have invigorated the urban forestry movement, and engaged politicians, planners, and the public in urban greening. Million tree initiatives have been launched in Los Angeles, CA; Denver, CO; New York City, NY; Philadelphia, PA, and other cities. Sacramento, CA even has a five million tree program. These...

Assessing urban forest effects and values, Chicago's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Cherie Leblanc Fisher

2010-01-01

An analysis of trees in Chicago, IL, reveals that this city has about 3,585,000 trees with canopies that cover 17.2 percent of the area. The most common tree species are white ash, mulberry species, green ash, and tree-of-heaven. Chicago's urban forest currently stores about 716,000 tons of carbon...

Green Infrastructure Increases Biogeochemical Responsiveness, Vegetation Growth and Decreases Runoff in a Semi-Arid City, Tucson, AZ, USA

NASA Astrophysics Data System (ADS)

Meixner, T.; Papuga, S. A.; Luketich, A. M.; Rockhill, T.; Gallo, E. L.; Anderson, J.; Salgado, L.; Pope, K.; Gupta, N.; Korgaonkar, Y.; Guertin, D. P.

2017-12-01

Green Infrastructure (GI) is often viewed as a mechanism to minimize the effects of urbanization on hydrology, water quality, and other ecosystem services (including the urban heat island). Quantifying the effects of GI requires field measurements of the dimensions of biogeochemical, ecosystem, and hydrologic function that we expect GI to impact. Here we investigated the effect of GI features in Tucson, Arizona which has a low intensity winter precipitation regime and a high intensity summer regime. We focused on understanding the effect of GI on soil hydraulic and biogeochemical properties as well as the effect on vegetation and canopy temperature. Our results demonstrate profound changes in biogeochemical and hydrologic properties and vegetation growth between GI systems and nearby control sites. In terms of hydrologic properties GI soils had increased water holding capacity and hydraulic conductivity. GI soils also have higher total carbon, total nitrogen, and organic matter in general than control soils. Furthermore, we tested the sampled soils (control and GI) for differences in biogeochemical response upon wetting. GI soils had larger respiration responses indicating greater biogeochemical activity overall. Long-term Lidar surveys were used to investigate the differential canopy growth of GI systems versus control sites. The results of this analysis indicate that while a significant amount of time is needed to observe differences in canopy growth GI features due increase tree size and thus likely impact street scale ambient temperatures. Additionally monitoring of transpiration, soil moisture, and canopy temperature demonstrates that GI features increase vegetation growth and transpiration and reduce canopy temperatures. These biogeochemical and ecohydrologic results indicate that GI can increase the biogeochemical processing of soils and increase tree growth and thus reduce urban ambient temperatures.

Parameterizing Urban Canopy Layer transport in an Lagrangian Particle Dispersion Model

NASA Astrophysics Data System (ADS)

Stöckl, Stefan; Rotach, Mathias W.

2016-04-01

The percentage of people living in urban areas is rising worldwide, crossed 50% in 2007 and is even higher in developed countries. High population density and numerous sources of air pollution in close proximity can lead to health issues. Therefore it is important to understand the nature of urban pollutant dispersion. In the last decades this field has experienced considerable progress, however the influence of large roughness elements is complex and has as of yet not been completely described. Hence, this work studied urban particle dispersion close to source and ground. It used an existing, steady state, three-dimensional Lagrangian particle dispersion model, which includes Roughness Sublayer parameterizations of turbulence and flow. The model is valid for convective and neutral to stable conditions and uses the kernel method for concentration calculation. As most Lagrangian models, its lower boundary is the zero-plane displacement, which means that roughly the lower two-thirds of the mean building height are not included in the model. This missing layer roughly coincides with the Urban Canopy Layer. An earlier work "traps" particles hitting the lower model boundary for a recirculation period, which is calculated under the assumption of a vortex in skimming flow, before "releasing" them again. The authors hypothesize that improving the lower boundary condition by including Urban Canopy Layer transport could improve model predictions. This was tested herein by not only trapping the particles, but also advecting them with a mean, parameterized flow in the Urban Canopy Layer. Now the model calculates the trapping period based on either recirculation due to vortex motion in skimming flow regimes or vertical velocity if no vortex forms, depending on incidence angle of the wind on a randomly chosen street canyon. The influence of this modification, as well as the model's sensitivity to parameterization constants, was investigated. To reach this goal, the model was initialized and compared with meteorological and SF6 tracer measurements from the Basel UrBan Boundary Layer Experiment (BUBBLE). The proposed modification does not improve the model's agreement with concentration observations, even though the trapping time shows promising agreement with measurements. Additionally, the modification's influence is smaller than those of different turbulence profiles, zero-plane displacement height and Roughness Sublayer height.

Measuring urban tree loss dynamics across residential landscapes.

PubMed

Ossola, Alessandro; Hopton, Matthew E

2018-01-15

The spatial arrangement of urban vegetation depends on urban morphology and socio-economic settings. Urban vegetation changes over time because of human management. Urban trees are removed due to hazard prevention or aesthetic preferences. Previous research attributed tree loss to decreases in canopy cover. However, this provides little information about location and structural characteristics of trees lost, as well as environmental and social factors affecting tree loss dynamics. This is particularly relevant in residential landscapes where access to residential parcels for field surveys is limited. We tested whether multi-temporal airborne LiDAR and multi-spectral imagery collected at a 5-year interval can be used to investigate urban tree loss dynamics across residential landscapes in Denver, CO and Milwaukee, WI, covering 400,705 residential parcels in 444 census tracts. Position and stem height of trees lost were extracted from canopy height models calculated as the difference between final (year 5) and initial (year 0) vegetation height derived from LiDAR. Multivariate regression models were used to predict number and height of tree stems lost in residential parcels in each census tract based on urban morphological and socio-economic variables. A total of 28,427 stems were lost from residential parcels in Denver and Milwaukee over 5years. Overall, 7% of residential parcels lost one stem, averaging 90.87 stems per km 2 . Average stem height was 10.16m, though trees lost in Denver were taller compared to Milwaukee. The number of stems lost was higher in neighborhoods with higher canopy cover and developed before the 1970s. However, socio-economic characteristics had little effect on tree loss dynamics. The study provides a simple method for measuring urban tree loss dynamics within and across entire cities, and represents a further step toward high resolution assessments of the three-dimensional change of urban vegetation at large spatial scales. Published by Elsevier B.V.

Urban trees and the risk of poor birth outcomes

Treesearch

Geoffrey H. Donovan; Yvonne L. Michael; David T. Butry; Amy D. Sullivan; John M. Chase

2011-01-01

This paper investigated whether greater tree-canopy cover is associated with reduced risk of poor birth outcomes in Portland, Oregon. Residential addresses were geocoded and linked to classified-aerial imagery to calculate tree-canopy cover in 50, 100, and 200 m buffers around each home in our sample (n=5696). Detailed data on maternal characteristics and additional...

The structure, function and value of urban forests in California communities

Treesearch

E. Gregory McPherson; Qingfu Xiao; Natalie S. van Doorn; John de Goede; Jacquelyn Bjorkman; Allan Hollander; Ryan M. Boynton; James F. Quinn; James H. Thorne

2017-01-01

This study used tree data from field plots in urban areas to describe forest structure in urban areas throughout California. The plot data were used with numerical models to calculate several ecosystem services produced by trees. A series of transfer functions were calculated to scale-up results from the plots to the landscape using urban tree canopy (UTC) mapped at 1-...

Assessing urban forest effects and values, Scranton's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Vincent Cotrone

2010-01-01

An analysis of trees in the urbanized portion of Scranton, PA, reveals that this area has about 1.2 million trees with canopies that cover 22.0 percent of the area. The most common tree species are red maple, gray birch, black cherry, northern red oak, and quaking aspen. Scranton's urban forest currently store about 93,300 tons of carbon valued at $1.9 million. In...

HIGH-RESOLUTION DATASET OF URBAN CANOPY PARAMETERS FOR HOUSTON, TEXAS

EPA Science Inventory

Urban dispersion and air quality simulation models applied at various horizontal scales require different levels of fidelity for specifying the characteristics of the underlying surfaces. As the modeling scales approach the neighborhood level (~1 km horizontal grid spacing), the...

Evaluation of four methods for estimating leaf area of isolated trees

Treesearch

P.J. Peper; E.G. McPherson

2003-01-01

The accurate modeling of the physiological and functional processes of urban forests requires information on the leaf area of urban tree species. Several non-destructive, indirect leaf area sampling methods have shown good performance for homogenous canopies. These methods have not been evaluated for use in urban settings where trees are typically isolated and...

Subpixel urban land cover estimation: comparing cubist, random forests, and support vector regression

Treesearch

Jeffrey T. Walton

2008-01-01

Three machine learning subpixel estimation methods (Cubist, Random Forests, and support vector regression) were applied to estimate urban cover. Urban forest canopy cover and impervious surface cover were estimated from Landsat-7 ETM+ imagery using a higher resolution cover map resampled to 30 m as training and reference data. Three different band combinations (...

COST 728 Project Report: Urbanization of Meteorological and Air Quality Models - Chapter 5 - Model Urbanization Strategy: Summaries, Recommendations and Requirements

EPA Science Inventory

The urban canopy (UC), the layer of the atmosphere between the ground and the top of the highest buildings, is the region where people live and human activities take place. Because of this importance (e.g., human health, preservation of buildings) significant efforts have been d...

Optimization of the scheme for natural ecology planning of urban rivers based on ANP (analytic network process) model.

PubMed

Zhang, Yichuan; Wang, Jiangping

2015-07-01

Rivers serve as a highly valued component in ecosystem and urban infrastructures. River planning should follow basic principles of maintaining or reconstructing the natural landscape and ecological functions of rivers. Optimization of planning scheme is a prerequisite for successful construction of urban rivers. Therefore, relevant studies on optimization of scheme for natural ecology planning of rivers is crucial. In the present study, four planning schemes for Zhaodingpal River in Xinxiang City, Henan Province were included as the objects for optimization. Fourteen factors that influenced the natural ecology planning of urban rivers were selected from five aspects so as to establish the ANP model. The data processing was done using Super Decisions software. The results showed that important degree of scheme 3 was highest. A scientific, reasonable and accurate evaluation of schemes could be made by ANP method on natural ecology planning of urban rivers. This method could be used to provide references for sustainable development and construction of urban rivers. ANP method is also suitable for optimization of schemes for urban green space planning and design.

Webinar Announcement - The Clean Water State Revolving Fund: Flexible Funding for the Urban Tree Canopy

EPA Pesticide Factsheets

This webinar, presented by the EPA and USDA, explores how the CWSRF can be used as a funding source for green infrastructure and urban forestry projects—a cost effective way to reduce combined sewage flooding problems.

High-resolution tree canopy mapping for New York City using LIDAR and object-based image analysis

NASA Astrophysics Data System (ADS)

MacFaden, Sean W.; O'Neil-Dunne, Jarlath P. M.; Royar, Anna R.; Lu, Jacqueline W. T.; Rundle, Andrew G.

2012-01-01

Urban tree canopy is widely believed to have myriad environmental, social, and human-health benefits, but a lack of precise canopy estimates has hindered quantification of these benefits in many municipalities. This problem was addressed for New York City using object-based image analysis (OBIA) to develop a comprehensive land-cover map, including tree canopy to the scale of individual trees. Mapping was performed using a rule-based expert system that relied primarily on high-resolution LIDAR, specifically its capacity for evaluating the height and texture of aboveground features. Multispectral imagery was also used, but shadowing and varying temporal conditions limited its utility. Contextual analysis was a key part of classification, distinguishing trees according to their physical and spectral properties as well as their relationships to adjacent, nonvegetated features. The automated product was extensively reviewed and edited via manual interpretation, and overall per-pixel accuracy of the final map was 96%. Although manual editing had only a marginal effect on accuracy despite requiring a majority of project effort, it maximized aesthetic quality and ensured the capture of small, isolated trees. Converting high-resolution LIDAR and imagery into usable information is a nontrivial exercise, requiring significant processing time and labor, but an expert system-based combination of OBIA and manual review was an effective method for fine-scale canopy mapping in a complex urban environment.

Modeling ozone uptake by urban and peri-urban forest: a case study in the Metropolitan City of Rome.

PubMed

Fusaro, Lina; Mereu, Simone; Salvatori, Elisabetta; Agliari, Elena; Fares, Silvano; Manes, Fausto

2018-03-01

Urban and peri-urban forests are green infrastructures (GI) that play a substantial role in delivering ecosystem services such as the amelioration of air quality by the removal of air pollutants, among which is ozone (O 3 ), which is the most harmful pollutant in Mediterranean metropolitan areas. Models may provide a reliable estimate of gas exchanges between vegetation and atmosphere and are thus a powerful tool to quantify and compare O 3 removal in different contexts. The present study modeled the O 3 stomatal uptake at canopy level of an urban and a peri-urban forest in the Metropolitan City of Rome in two different years. Results show different rates of O 3 fluxes between the two forests, due to different exposure to the pollutant, management practice effects on forest structure and functionality, and environmental conditions, namely, different stressors affecting the gas exchange rates of the two GIs. The periodic components of the time series calculated by means of the spectral analysis show that seasonal variation of modeled canopy transpiration is driven by precipitation in peri-urban forests, whereas in the urban forest seasonal variations are driven by vapor pressure deficit of ambient air. Moreover, in the urban forest high water availability during summer months, owing to irrigation practice, leads to an increase in O 3 uptake, thus suggesting that irrigation may enhance air phytoremediation in urban areas.

Model Urbanization Strategy: Summaries, Recommendations and Requirements

EPA Science Inventory

The urban canopy (UC), the layer of the atmosphere between the ground and the top of the highest buildings, is the region where people live and human activities take place. Because of this importance (e.g., human health, preservation of buildings) significant efforts have been de...

Neighbourhood-scale urban forest ecosystem classification.

PubMed

Steenberg, James W N; Millward, Andrew A; Duinker, Peter N; Nowak, David J; Robinson, Pamela J

2015-11-01

Urban forests are now recognized as essential components of sustainable cities, but there remains uncertainty concerning how to stratify and classify urban landscapes into units of ecological significance at spatial scales appropriate for management. Ecosystem classification is an approach that entails quantifying the social and ecological processes that shape ecosystem conditions into logical and relatively homogeneous management units, making the potential for ecosystem-based decision support available to urban planners. The purpose of this study is to develop and propose a framework for urban forest ecosystem classification (UFEC). The multifactor framework integrates 12 ecosystem components that characterize the biophysical landscape, built environment, and human population. This framework is then applied at the neighbourhood scale in Toronto, Canada, using hierarchical cluster analysis. The analysis used 27 spatially-explicit variables to quantify the ecosystem components in Toronto. Twelve ecosystem classes were identified in this UFEC application. Across the ecosystem classes, tree canopy cover was positively related to economic wealth, especially income. However, education levels and homeownership were occasionally inconsistent with the expected positive relationship with canopy cover. Open green space and stocking had variable relationships with economic wealth and were more closely related to population density, building intensity, and land use. The UFEC can provide ecosystem-based information for greening initiatives, tree planting, and the maintenance of the existing canopy. Moreover, its use has the potential to inform the prioritization of limited municipal resources according to ecological conditions and to concerns of social equity in the access to nature and distribution of ecosystem service supply. Copyright © 2015 Elsevier Ltd. All rights reserved.

Patterns in understory woody diversity and soil nitrogen across native- and non-native-urban tropical forests

Treesearch

D.F. Cusack; T.L. McCleery; NO-VALUE

2014-01-01

Urban expansion is accelerating in the tropics, and may promote the spread of introduced plant species into urban-proximate forests. For example, soil disturbance can deplete the naturally high soil nitrogen pools in wet tropical soils, favoring introduced species with nitrogen-fixing capabilities. Also, forest fragmentation and canopy disturbance are likely to favor...

Assessing urban forest effects and values: Morgantown's Urban Forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jonathan Cumming; Sandhya Mohen; Anne Buckelew. Cumming

2012-01-01

An analysis of the community forest in Morgantown, WV, was undertaken in 2004 to characterize the structural and functional attributes of this forest resource. The assessment revealed that this city has about 658,000 trees with canopies that cover 35.5 percent of the area. The most common tree species are sugar maple, black cherry, and hawthorn. The urban forest...

NEIGHBORHOOD SCALE AIR QUALITY MODELING IN HOUSTON USING URBAN CANOPY PARAMETERS IN MM5 AND CMAQ WITH IMPROVED CHARACTERIZATION OF MESOSCALE LAKE-LAND BREEZE CIRCULATION

EPA Science Inventory

Advanced capability of air quality simulation models towards accurate performance at finer scales will be needed for such models to serve as tools for performing exposure and risk assessments in urban areas. It is recognized that the impact of urban features such as street and t...

Growing the urban forest: tree performance in response to biotic and abiotic land management

Treesearch

Emily E. Oldfield; Alexander J. Felson; D. S. Novem Auyeung; Thomas W. Crowther; Nancy F. Sonti; Yoshiki Harada; Daniel S. Maynard; Noah W. Sokol; Mark S. Ashton; Robert J. Warren; Richard A. Hallett; Mark A. Bradford

2015-01-01

Forests are vital components of the urban landscape because they provide ecosystem services such as carbon sequestration, storm-water mitigation, and air-quality improvement. To enhance these services, cities are investing in programs to create urban forests. A major unknown, however, is whether planted trees will grow into the mature, closed-canopied forest on which...

Trees and Streets as Drivers of Urban Stormwater Nutrient Pollution.

PubMed

Janke, Benjamin D; Finlay, Jacques C; Hobbie, Sarah E

2017-09-05

Expansion of tree cover is a major management goal in cities because of the substantial benefits provided to people, and potentially to water quality through reduction of stormwater volume by interception. However, few studies have addressed the full range of potential impacts of trees on urban runoff, which includes deposition of nutrient-rich leaf litter onto streets connected to storm drains. We analyzed the influence of trees on stormwater nitrogen and phosphorus export across 19 urban watersheds in Minneapolis-St. Paul, MN, U.S.A., and at the scale of individual streets within one residential watershed. Stormwater nutrient concentrations were highly variable across watersheds and strongly related to tree canopy over streets, especially for phosphorus. Stormwater nutrient loads were primarily related to road density, the dominant control over runoff volume. Street canopy exerted opposing effects on loading, where elevated nutrient concentrations from trees near roads outweighed the weak influence of trees on runoff reduction. These results demonstrate that vegetation near streets contributes substantially to stormwater nutrient pollution, and therefore to eutrophication of urban surface waters. Urban landscape design and management that account for trees as nutrient pollution sources could improve water quality outcomes, while allowing cities to enjoy the myriad benefits of urban forests.

The atmospheric boundary layer — advances in knowledge and application

NASA Astrophysics Data System (ADS)

Garratt, J. R.; Hess, G. D.; Physick, W. L.; Bougeault, P.

1996-02-01

We summarise major activities and advances in boundary-layer knowledge in the 25 years since 1970, with emphasis on the application of this knowledge to surface and boundary-layer parametrisation schemes in numerical models of the atmosphere. Progress in three areas is discussed: (i) the mesoscale modelling of selected phenomena; (ii) numerical weather prediction; and (iii) climate simulations. Future trends are identified, including the incorporation into models of advanced cloud schemes and interactive canopy schemes, and the nesting of high resolution boundary-layer schemes in global climate models.

Albedo and its Relationship to Land Cover and the Urban Heat Island in the Boston Metropolitan Region

NASA Astrophysics Data System (ADS)

Trlica, A.; Hutyra, L.; Wang, J.; Schaaf, C.; Erb, A.

2016-12-01

The urban built environment creates key changes in the biophysical character of the landscape, including the creation of Urban Heat Islands (UHIs) with increased near-surface temperatures in and around cities. Alteration in surface albedo is believed to partially drive UHIs through greater absorption of solar energy, but few empirical studies have specifically quantified albedo across a heterogeneous urban landscape, or investigated linkages between albedo, the UHI, and other surface socio-biophysical characteristics at a high enough spatial resolution to discern urban-scale features. This study used data derived from observations by Landsat and other remote sensing platforms to measure albedo across a varied urban landscape centered on Boston, Massachusetts, and examined the relationship between albedo, several key indicators of urban surface character (canopy cover, impervious fraction, and population density) and land surface temperature at resolutions of both 30 and 500 m. Albedo tended to be lower in areas with highest urbanization intensity indicators compared to rural undeveloped areas, and areas with lower albedo tended also to have higher median daytime summer surface temperatures. A k-means classification utilizing all the data available for each pixel revealed several distinct patterns of urban land cover corresponding mainly to the density of population and constructed surfaces and their impact on tree canopy cover. Mean 30-m summer surface temperatures ranged from 40.0 °C (SD = 2.6) in urban core areas to 26.2 °C (SD = 1.1) in nearby forest, but we only observed correspondingly large albedo decreases in the highest density urban core, with mean albedo of 0.116 (SD = 0.015) compared with 0.155 (SD = 0.015) in forest. Observations show that lower albedo in the Boston metropolitan region may be an important component of the local UHI in the most densely built-up urban core regions, while the UHI temperature effect in less densely settled peripheral regions is more likely to be driven primarily by reduced evapotranspiration due to diminished tree canopy and greater impervious surface coverage. These results empirically characterize surface albedo across a suite of land cover categories and biophysical characteristics and reveal how albedo relates to surface temperatures in this urbanized region.

Inclusion of an ultraviolet radiation transfer component in an urban forest effects model for predicting tree influences on potential below-canopy exposure to UVB radiation

Treesearch

Gordon M. Heisler; Richard H. Grant; David J. Nowak; Wei Gao; Daniel E. Crane; Jeffery T. Walton

2003-01-01

Evaluating the impact of ultraviolet-B radiation (UVB) on urban populations would be enhanced by improved predictions of the UVB radiation at the level of human activity. This paper reports the status of plans for incorporating a UVB prediction module into an existing Urban Forest Effects (UFORE) model. UFORE currently has modules to quantify urban forest structure,...

Identification of terrain cover using the optimum polarimetric classifier

NASA Technical Reports Server (NTRS)

Kong, J. A.; Swartz, A. A.; Yueh, H. A.; Novak, L. M.; Shin, R. T.

1988-01-01

A systematic approach for the identification of terrain media such as vegetation canopy, forest, and snow-covered fields is developed using the optimum polarimetric classifier. The covariance matrices for various terrain cover are computed from theoretical models of random medium by evaluating the scattering matrix elements. The optimal classification scheme makes use of a quadratic distance measure and is applied to classify a vegetation canopy consisting of both trees and grass. Experimentally measured data are used to validate the classification scheme. Analytical and Monte Carlo simulated classification errors using the fully polarimetric feature vector are compared with classification based on single features which include the phase difference between the VV and HH polarization returns. It is shown that the full polarimetric results are optimal and provide better classification performance than single feature measurements.

Characterization and Low-Dimensional Modeling of Urban Fluid Flow

DTIC Science & Technology

2014-10-06

4 2 Wind Tunnel , Apparatus and Data Processing 7 2.1 Modelling of the Atmospheric Boundary Layer...was demonstrated. Most notably, wind tunnel experiments were performed at a number of different angles of incidence, providing for the first time a...Coceal and Belcher [2004] developed an urban canopy model for mean winds in urban areas that compares well with data from wind tunnel experiments

A new approach to quantify and map carbon stored, sequestered and emissions avoided by urban forests

Treesearch

E. Gregory McPherson; Qingfu Xiao; Elena Aguaron

2013-01-01

This paper describes the use of field surveys, biometric information for urban tree species and remote sensing to quantify and map carbon (C) storage, sequestration and avoided emissions from energy savings. Its primary contribution is methodological; the derivation and application of urban tree canopy (UTC) based transfer functions (t C ha-1 UTC). Findings for Los...

Focusing on the big picture: urban vegetation and eco-hydrological services in U.S. cities (abstract)

EPA Science Inventory

Trees and vegetation can be key components of urban green infrastructure and green spaces such as parks and residential yards. Large trees, characterized by broad canopies, and high leaf and stem volumes, can intercept a substantial amount of stormwater while promoting evapotrans...

INTRODUCTION OF URBAN CANOPY PARAMETERIZATION INTO MM5 TO SIMULATE URBAN METEOROLOGY AT NEIGHBORHOOD SCALE

EPA Science Inventory

Since most of the primary atmospheric pollutants are emitted inside the roughness sub-layer (RSL) and consequently the first chemical reactions and dispersion occur in this layer, it is necessary to generate detailed meteorological fields inside the RSL to perform air quality m...

IMPLEMENTATION OF AN URBAN CANOPY PARAMETERIZATION IN MM5 FOR MESO-GAMMA-SCALE AIR QUALITY MODELING APPLICATIONS

EPA Science Inventory

The U.S. Environmental Protection Agency (U.S. EPA) is extending its Models-3/Community Multiscale Air Quality (CMAQ) Modeling System to provide detailed gridded air quality concentration fields and sub-grid variability characterization at neighborhood scales and in urban areas...

America's Urban Forests: Keeping Our Cities Cool

NASA Technical Reports Server (NTRS)

Luvall, Jeffrey C.; Quattrochi, Dale A.

1997-01-01

The additional heating of the air over the city is the result of the replacement of naturally vegetated surfaces with those composed of asphalt, concrete, rooftops and other man-made materials. The temperatures of these artificial surfaces can be 20 to 40 C higher than vegetated surfaces. Materials such as asphalt store much of the sun's energy and remains hot long after sunset. This produces a dome of elevated air temperatures 5 to 8 C greater over the city, compared to the air temperatures over adjacent rural areas. This effect is called the "urban heat island". Tree canopies can reduce the urban heat island effect by dissipating the solar energy received by transpiring water from leaf surfaces which cools the air by taking "heat" from the air to evaporate the water and by shading surfaces like asphalt, roofs, and concrete parking lots which prevents initial heating and storage of heat. It is difficult to take enough temperature measurements over a large city area to characterize the surface temperature variability and quantify the temperature reduction effects of tree canopies. However, the use of remotely sensed thermal data from airborne scanners are ideal for the task. In a study funded by NASA, a series of flights over Huntsville AL were performed in September 1994 and over Atlanta in May 1997. In this article we will examine the techniques of analyzing remotely sensed data for measuring the effect of tree canopies in reducing the urban heat island effect.

Mapping carbon storage in urban trees with multi-source remote sensing data: relationships between biomass, land use, and demographics in Boston neighborhoods.

PubMed

Raciti, Steve M; Hutyra, Lucy R; Newell, Jared D

2014-12-01

High resolution maps of urban vegetation and biomass are powerful tools for policy-makers and community groups seeking to reduce rates of urban runoff, moderate urban heat island effects, and mitigate the effects of greenhouse gas emissions. We developed a very high resolution map of urban tree biomass, assessed the scale sensitivities in biomass estimation, compared our results with lower resolution estimates, and explored the demographic relationships in biomass distribution across the City of Boston. We integrated remote sensing data (including LiDAR-based tree height estimates) and field-based observations to map canopy cover and aboveground tree carbon storage at ~1m spatial scale. Mean tree canopy cover was estimated to be 25.5±1.5% and carbon storage was 355Gg (28.8MgCha(-1)) for the City of Boston. Tree biomass was highest in forest patches (110.7MgCha(-1)), but residential (32.8MgCha(-1)) and developed open (23.5MgCha(-1)) land uses also contained relatively high carbon stocks. In contrast with previous studies, we did not find significant correlations between tree biomass and the demographic characteristics of Boston neighborhoods, including income, education, race, or population density. The proportion of households that rent was negatively correlated with urban tree biomass (R(2)=0.26, p=0.04) and correlated with Priority Planting Index values (R(2)=0.55, p=0.001), potentially reflecting differences in land management among rented and owner-occupied residential properties. We compared our very high resolution biomass map to lower resolution biomass products from other sources and found that those products consistently underestimated biomass within urban areas. This underestimation became more severe as spatial resolution decreased. This research demonstrates that 1) urban areas contain considerable tree carbon stocks; 2) canopy cover and biomass may not be related to the demographic characteristics of Boston neighborhoods; and 3) that recent advances in high resolution remote sensing have the potential to improve the characterization and management of urban vegetation. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of trees on momentum exchange within and above a real urban environment

NASA Astrophysics Data System (ADS)

Salesky, S.; Giometto, M. G.; Christen, A.; Egli, P. E.; Schmid, M. F.; Tooke, T. R.; Coops, N. C.; Parlange, M. B.

2017-12-01

Large-eddy simulations (LES) are used to gain insight into the effects of trees on momentum transfer rates characterizing the atmosphere within and above a real urban canopy. Several areas are considered that are part of a neighbourhood in the city of Vancouver, BC, Canada where a small fraction of trees are taller than buildings. In this area, eight years of continuous wind and turbulence measurements are available from a 30 m meteorological tower. Buildings and vegetation geometries are obtained from airborne light detection and ranging (LiDAR) data. In the LES algorithm, buildings are accounted through an immersed boundary method, whereas vegetation is parameterized via a location-specific leaf area density. LES are performed varying wind direction and leaf area densities. Surface roughness lengths (z0) from both LES and tower measurements are sensitive to the 0 ≤ LAI/λ < 3 parameter, where LAI is the leaf area index and λ is the frontal area fraction of buildings characterizing a given canopy. For instance, tower measurements predict a 19% seasonal increase in z0, slightly lower than the 27% increase featured by LES for the most representative canopy (leaves-off LAI/λ = 0.74, leaves-on LAI/λ = 2.24). Removing vegetation from such a canopy would cause a dramatic drop of approximately 50% in z0 when compared to the reference summer value. The momentum displacement height (d) from LES also consistently increases as LAI/λ increases, due to the disproportionate amount of drag that the (few) relatively taller trees exert on the flow. Within the urban canopy, the effects of trees are twofold: on one hand, they act as a direct momentum sink for the mean flow; on the other, they reduce downward turbulent transport of high-momentum fluid, significantly reducing the wind intensity at the heights where people live and buildings consume energy.

Extreme heat event projections for a coastal megacity

NASA Astrophysics Data System (ADS)

Ortiz, L. E.; Gonzalez, J.

2017-12-01

As summers become warmer, extreme heat events are expected to increase in intensity, frequency, and duration. Large urban centers may affect these projections by introducing feedbacks between the atmosphere and the built environment through processes involving anthropogenic heat, wind modification, radiation blocking, and others. General circulation models are often run with spatial resolutions in the order of 100 km, limiting their skill at resolving local scale processes and highly spatially varying features such as cities' heterogeneous landscape and mountain topography. This study employs climate simulations using the Weather Research and Forecast (WRF) model coupled with a modified multi-layer urban canopy and building energy model to downscale CESM1 at 1 km horizontal resolution across three time slices (2006-2010, 2075-2079, and 2095-2099) and two projections (RCP 4.5 and 8.5). New York City Metropolitan area, with a population of over 20 million and a complex urban canopy, is used as a case study. The urban canopy model of WRF was modified to include a drag coefficient as a function of the building plant area fraction and the introduction of evaporative cooling systems at building roofs to reject the anthropogenic heat from the buildings, with urban canopy parameters computed from the New York City Property Land-Use Tax-lot Output (PLUTO). Model performance is evaluated against the input model and historical records from airport stations, showing improvement in the statistical characteristics in the downscaled model output. Projection results are presented as spatially distributed anomalies in heat wave frequency, duration, and maximum intensity from the 2006-2010 benchmark period. Results show that local sea-breeze circulations mitigate heat wave impacts, following a positive gradient with increasing distance from the coastline. However, end of century RCP 8.5 projections show the possibility of reversal of this pattern, sea surface temperatures increase and reduce the sea-land temperature gradient, thus reducing the sea-breeze magnitude. Impacts to human health and buildings energy demand are explored for future climate scenarios as key examples of anticipated societal consequences.

Air quality modelling in the Berlin-Brandenburg region using WRF-Chem v3.7.1: sensitivity to resolution of model grid and input data

NASA Astrophysics Data System (ADS)

Kuik, Friderike; Lauer, Axel; Churkina, Galina; Denier van der Gon, Hugo A. C.; Fenner, Daniel; Mar, Kathleen A.; Butler, Tim M.

2016-12-01

Air pollution is the number one environmental cause of premature deaths in Europe. Despite extensive regulations, air pollution remains a challenge, especially in urban areas. For studying summertime air quality in the Berlin-Brandenburg region of Germany, the Weather Research and Forecasting Model with Chemistry (WRF-Chem) is set up and evaluated against meteorological and air quality observations from monitoring stations as well as from a field campaign conducted in 2014. The objective is to assess which resolution and level of detail in the input data is needed for simulating urban background air pollutant concentrations and their spatial distribution in the Berlin-Brandenburg area. The model setup includes three nested domains with horizontal resolutions of 15, 3 and 1 km and anthropogenic emissions from the TNO-MACC III inventory. We use RADM2 chemistry and the MADE/SORGAM aerosol scheme. Three sensitivity simulations are conducted updating input parameters to the single-layer urban canopy model based on structural data for Berlin, specifying land use classes on a sub-grid scale (mosaic option) and downscaling the original emissions to a resolution of ca. 1 km × 1 km for Berlin based on proxy data including traffic density and population density. The results show that the model simulates meteorology well, though urban 2 m temperature and urban wind speeds are biased high and nighttime mixing layer height is biased low in the base run with the settings described above. We show that the simulation of urban meteorology can be improved when specifying the input parameters to the urban model, and to a lesser extent when using the mosaic option. On average, ozone is simulated reasonably well, but maximum daily 8 h mean concentrations are underestimated, which is consistent with the results from previous modelling studies using the RADM2 chemical mechanism. Particulate matter is underestimated, which is partly due to an underestimation of secondary organic aerosols. NOx (NO + NO2) concentrations are simulated reasonably well on average, but nighttime concentrations are overestimated due to the model's underestimation of the mixing layer height, and urban daytime concentrations are underestimated. The daytime underestimation is improved when using downscaled, and thus locally higher emissions, suggesting that part of this bias is due to deficiencies in the emission input data and their resolution. The results further demonstrate that a horizontal resolution of 3 km improves the results and spatial representativeness of the model compared to a horizontal resolution of 15 km. With the input data (land use classes, emissions) at the level of detail of the base run of this study, we find that a horizontal resolution of 1 km does not improve the results compared to a resolution of 3 km. However, our results suggest that a 1 km horizontal model resolution could enable a detailed simulation of local pollution patterns in the Berlin-Brandenburg region if the urban land use classes, together with the respective input parameters to the urban canopy model, are specified with a higher level of detail and if urban emissions of higher spatial resolution are used.

Comparing large eddy simulations and measurements of the turbulent kinetic energy budget in an urban canopy layer

NASA Astrophysics Data System (ADS)

Parlange, M. B.; Giometto, M. G.; Meneveau, C. V.; Fang, J.; Christen, A.

2013-12-01

Local turbulent kinetic energy (TKE) in the Urban Canopy Layer (UCL) is highly dependent on the actual configuration of obstacles relative to mean wind and stability. For many applications, building-resolving information is neither required nor feasible, and simply beyond the numerical capabilities of operational systems. Common urban canopy parameterizations (UCP) used in dispersion and mesoscale forecasting models hence rely on a horizontally averaged approach, where the UCL is represented as a 1D column, often for simplified geometries such as infinite street canyons. We use Large Eddy Simulations (LES) of the airflow over and within a realistic urban geometry in the city of Basel, Switzerland to determine all terms of the TKE budget in order to guide and validate current approaches used in UCPs. A series of high-resolution LES runs of the fully developed flow are performed in order to characterize the TKE budget terms in a horizontally averaged frame of view for various directions of the approaching flow under neutral conditions. Equations are solved on a regular domain with a horizontal resolution of 2 m. A Lagrangian scale-dependent LES model is adopted to parametrize the subgrid-scale stresses and buildings are taken into account adopting an immersed boundary approach with the geometry taken from a highly accurate digital building model. The modeled (periodic) domain is centered on the location of a 32 m tall tower, where measurements of turbulence were performed, during the BUBBLE program in 2001/02 (Rotach et al., Theor. Appl. Clim., 82, 231-261, 2005). Selected terms of the TKE budget were inferred from six levels of ultrasonic anemometer measurements operated over nearly a full year between ground level and two times the mean building height. This contribution answers the questions: (1) How well do TKE budget terms calculated by the LES at the exact tower location match the single point measurements on the tower under comparable conditions? (2) How representative are the single-point measurements at the tower-location compared to the horizontally-averaged TKE budget in the entire urban domain? (3) How important are non-measurable terms of the TKE budget (wake production, dispersive transport, pressure transport) under the current real urban geometry? Our results show good statistical agreement between tower measurements and numerically resolved quantities, validating the model and confirming our immersed boundary approach in the LES a valuable tool to study turbulence and dispersion within real UCLs. Turbulent kinetic energy (TKE) in the UCL is primarily produced at roof-level, and turbulence is transported down into the cavities of the urban canopy (street canyons, backyards). From our results it is also clear how tower measurements cannot be used to quantify all terms in a horizontally-averaged view and the non-measured dispersive terms are important in a real canopy.

Stable Stratification Effects on Flow and Pollutant Dispersion in Boundary Layers Entering a Generic Urban Environment

NASA Astrophysics Data System (ADS)

Tomas, J. M.; Pourquie, M. J. B. M.; Jonker, H. J. J.

2016-05-01

Large-eddy simulations (LES) are used to investigate the effect of stable stratification on rural-to-urban roughness transitions. Smooth-wall turbulent boundary layers are subjected to a generic urban roughness consisting of cubes in an in-line arrangement. Two line sources of pollutant are added to investigate the effect on pollutant dispersion. Firstly, the LES method is validated with data from wind-tunnel experiments on fully-developed flow over cubical roughness. Good agreement is found for the vertical profiles of the mean streamwise velocity component and mean Reynolds stress. Subsequently, roughness transition simulations are done for both neutral and stable conditions. Results are compared with fully-developed simulations with conventional double-periodic boundary conditions. In stable conditions, at the end of the domain the streamwise velocity component has not yet reached the fully-developed state even though the surface forces are nearly constant. Moreover, the internal boundary layer is shallower than in the neutral case. Furthermore, an investigation of the turbulence kinetic energy budget shows that the buoyancy destruction term is reduced in the internal boundary layer, above which it is equal to the undisturbed (smooth wall) value. In addition, in stable conditions pollutants emitted above the urban canopy enter the canopy farther downstream due to decreased vertical mixing. Pollutants emitted below the top of the urban canopy are 85 % higher in concentration in stable conditions mostly due to decreased advection. If this is taken into account concentrations remain 17 % greater in stable conditions due to less rapid internal boundary-layer growth. Finally, it is concluded that in the first seven streets the vertical advective pollutant flux is significant, in contrast to the fully-developed case.

Pollutant Dispersion in Boundary Layers Exposed to Rural-to-Urban Transitions: Varying the Spanwise Length Scale of the Roughness

NASA Astrophysics Data System (ADS)

Tomas, J. M.; Eisma, H. E.; Pourquie, M. J. B. M.; Elsinga, G. E.; Jonker, H. J. J.; Westerweel, J.

2017-05-01

Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic particle image velocimetry and laser-induced fluorescence, have been used to investigate pollutant dispersion mechanisms in regions where the surface changes from rural to urban roughness. The urban roughness was characterized by an array of rectangular obstacles in an in-line arrangement. The streamwise length scale of the roughness was kept constant, while the spanwise length scale was varied by varying the obstacle aspect ratio l / h between 1 and 8, where l is the spanwise dimension of the obstacles and h is the height of the obstacles. Additionally, the case of two-dimensional roughness (riblets) was considered in LES. A smooth-wall turbulent boundary layer of depth 10 h was used as the approaching flow, and a line source of passive tracer was placed 2 h upstream of the urban canopy. The experimental and numerical results show good agreement, while minor discrepancies are readily explained. It is found that for l/h=2 the drag induced by the urban canopy is largest of all considered cases, and is caused by a large-scale secondary flow. In addition, due to the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identified that is responsible for street-canyon ventilation for the sixth street and onwards. Moreover, it is shown that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the canopy, while the streamwise length scale does not show a similar trend.

A model of canopy photosynthesis incorporating protein distribution through the canopy and its acclimation to light, temperature and CO2

PubMed Central

Johnson, Ian R.; Thornley, John H. M.; Frantz, Jonathan M.; Bugbee, Bruce

2010-01-01

Background and Aims The distribution of photosynthetic enzymes, or nitrogen, through the canopy affects canopy photosynthesis, as well as plant quality and nitrogen demand. Most canopy photosynthesis models assume an exponential distribution of nitrogen, or protein, through the canopy, although this is rarely consistent with experimental observation. Previous optimization schemes to derive the nitrogen distribution through the canopy generally focus on the distribution of a fixed amount of total nitrogen, which fails to account for the variation in both the actual quantity of nitrogen in response to environmental conditions and the interaction of photosynthesis and respiration at similar levels of complexity. Model A model of canopy photosynthesis is presented for C3 and C4 canopies that considers a balanced approach between photosynthesis and respiration as well as plant carbon partitioning. Protein distribution is related to irradiance in the canopy by a flexible equation for which the exponential distribution is a special case. The model is designed to be simple to parameterize for crop, pasture and ecosystem studies. The amount and distribution of protein that maximizes canopy net photosynthesis is calculated. Key Results The optimum protein distribution is not exponential, but is quite linear near the top of the canopy, which is consistent with experimental observations. The overall concentration within the canopy is dependent on environmental conditions, including the distribution of direct and diffuse components of irradiance. Conclusions The widely used exponential distribution of nitrogen or protein through the canopy is generally inappropriate. The model derives the optimum distribution with characteristics that are consistent with observation, so overcoming limitations of using the exponential distribution. Although canopies may not always operate at an optimum, optimization analysis provides valuable insight into plant acclimation to environmental conditions. Protein distribution has implications for the prediction of carbon assimilation, plant quality and nitrogen demand. PMID:20861273

Thermal signatures of urban land cover types: High-resolution thermal infrared remote sensing of urban heat island in Huntsville, AL

NASA Technical Reports Server (NTRS)

Lo, Chor Pang

1996-01-01

The main objective of this research is to apply airborne high-resolution thermal infrared imagery for urban heat island studies, using Huntsville, AL, a medium-sized American city, as the study area. The occurrence of urban heat islands represents human-induced urban/rural contrast, which is caused by deforestation and the replacement of the land surface by non-evaporating and non-porous materials such as asphalt and concrete. The result is reduced evapotranspiration and more rapid runoff of rain water. The urban landscape forms a canopy acting as a transitional zone between the atmosphere and the land surface. The composition and structure of this canopy have a significant impact on the thermal behavior of the urban environment. Research on the trends of surface temperature at rapidly growing urban sites in the United States during the last 30 to 50 years suggests that significant urban heat island effects have caused the temperatures at these sites to rise by 1 to 2 C. Urban heat islands have caused changes in urban precipitation and temperature that are at least similar to, if not greater than, those predicted to develop over the next 100 years by global change models. Satellite remote sensing, particularly NOAA AVHRR thermal data, has been used in the study of urban heat islands. Because of the low spatial resolution (1.1 km at nadir) of the AVHRR data, these studies can only examine and map the phenomenon at the macro-level. The present research provides the rare opportunity to utilize 5-meter thermal infrared data acquired from an airplane to characterize more accurately the thermal responses of different land cover types in the urban landscape as input to urban heat island studies.

Assessing urban forest effects and values, Minneapolis' urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Minneapolis, MN, reveals that the city has about 979,000 trees with canopies that cover 26.4 percent of the area. The most common tree species are green ash, American elm, and boxelder. The urban forest currently stores about 250,000 tons of carbon valued at $4.6 million. In addition, these trees remove about 8,900 tons of carbon per year ($164,...

Assessing urban forest effects and values, Casper's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Casper, WY reveals that this city has about 123,000 trees with canopies that cover 8.9 percent of the area. The most common tree species are plains cottonwood, blue spruce, and American elm. The urban forest currently store about 37,000 tons of carbon valued at $689,000. In addition, these trees remove about 1,200 tons of carbon per year ($22,...

Assessing urban forest effects and values: Toronto's urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Allison R. Bodine; Eric J. Greenfield; Alexis Ellis; Theodore A. Endreny; Yang Yang; Tian Zhou; Ruthanne Henry

2013-01-01

An analysis of trees in Toronto, Ontario, reveals that this city has about 10.2 million trees with a tree and shrub canopy that covers approximately 26.6 percent of the city. The most common tree species are eastern white-cedar, sugar maple, and Norway maple. The urban forest currently stores an estimated 1.1 million metric tons of carbon valued at CAD$25.0 million. In...

Assessing urban forest effects and values, Philladelphia's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in Philadelphia reveals that this city has about 2.1 million trees with canopies that cover 15.7 percent of the area. The most common tree species are black cherry, crabapple, and tree of heaven. The urban forest currently stores about 530,000 tons of carbon valued at $9.8 million. In addition, these trees remove about 16,100 tons of carbon per...

Assessing urban forest effects and values, San Francisco's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in San Francisco, CA reveals that this city has about 669,000 trees with canopies that cover 11.9 percent of the area. The most common tree species are blue gum eucalyptus, Monterey pine, and Monterey cypress. The urban forest currently stores about 196,000 tons of carbon valued at $3.6 million. In addition, these trees remove about 5,200 tons of...

Roles of Urban Tree Canopy and Buildings in Urban Heat Island Effects: Parameterization and Preliminary Results

NASA Technical Reports Server (NTRS)

Loughner, Christopher P.; Allen, Dale J.; Zhang, Da-Lin; Pickering, Kenneth E.; Dickerson, Russell R.; Landry, Laura

2012-01-01

Urban heat island (UHI) effects can strengthen heat waves and air pollution episodes. In this study, the dampening impact of urban trees on the UHI during an extreme heat wave in the Washington, D.C., and Baltimore, Maryland, metropolitan area is examined by incorporating trees, soil, and grass into the coupled Weather Research and Forecasting model and an urban canopy model (WRF-UCM). By parameterizing the effects of these natural surfaces alongside roadways and buildings, the modified WRF-UCM is used to investigate how urban trees, soil, and grass dampen the UHI. The modified model was run with 50% tree cover over urban roads and a 10% decrease in the width of urban streets to make space for soil and grass alongside the roads and buildings. Results show that, averaged over all urban areas, the added vegetation decreases surface air temperature in urban street canyons by 4.1 K and road-surface and building-wall temperatures by 15.4 and 8.9 K, respectively, as a result of tree shading and evapotranspiration. These temperature changes propagate downwind and alter the temperature gradient associated with the Chesapeake Bay breeze and, therefore, alter the strength of the bay breeze. The impact of building height on the UHI shows that decreasing commercial building heights by 8 m and residential building heights by 2.5 m results in up to 0.4-K higher daytime surface and near-surface air temperatures because of less building shading and up to 1.2-K lower nighttime temperatures because of less longwave radiative trapping in urban street canyons.

Ten-year performance of the United States national elm trial

Treesearch

Jason J. Griffin; William R. Jacobi; E. Gregory McPherson; Clifford S. Sadof; James R. McKenna; Mark L. Gleason; Nicole Ward Gauthier; Daniel A. Potter; David R. Smitley; Gerard C. Adams; Ann Brooks Gould; Christian R. Cash; James A. Walla; Mark C. Starrett; Gary Chastagner; Jeff L. Sibley; Vera A. Krischik; Adam F. Newby

2017-01-01

Ulmus americana (American elm) was an important urban tree in North America prior to the introduction of the Dutch elm disease pathogen in 1930. Subsequently, urban and community forests were devastated by the loss of large canopies. Tree improvement programs produced disease tolerant American and Eurasian elm cultivars and introduced them into the...

Multi-scale comparison of the fine particle removal capacity of urban forests and wetlands.

PubMed

Zhang, Zhenming; Liu, Jiakai; Wu, Yanan; Yan, Guoxin; Zhu, Lijuan; Yu, Xinxiao

2017-04-10

As fine particle (FP) pollution is harmful to humans, previous studies have focused on the mechanisms of FP removal by forests. The current study aims to compare the FP removal capacities of urban forests and wetlands on the leaf, canopy, and landscape scales. Water washing and scanning electron microscopy are used to calculate particle accumulation on leaves, and models are used to estimate vegetation collection, sedimentation, and dry deposition. Results showed that, on the leaf scale, forest species are able to accumulate more FP on their leaf surface than aquatic species in wetlands. On the canopy scale, horizontal vegetation collection is the major process involved in FP removal, and the contribution of vertical sedimentation/emission can be ignored. Coniferous tree species also showed stronger FP collection ability than broadleaf species. In the landscape scale, deposition on the forest occurs to a greater extent than that on wetlands, and dry deposition is the major process of FP removal on rain-free days. In conclusion, when planning an urban green system, planting an urban forest should be the first option for FP mitigation.

Evaluation of the Event Driven Phenology Model Coupled with the VegET Evapotranspiration Model Through Comparisons with Reference Datasets in a Spatially Explicit Manner

NASA Technical Reports Server (NTRS)

Kovalskyy, V.; Henebry, G. M.; Adusei, B.; Hansen, M.; Roy, D. P.; Senay, G.; Mocko, D. M.

2011-01-01

A new model coupling scheme with remote sensing data assimilation was developed for estimation of daily actual evapotranspiration (ET). The scheme represents a mix of the VegET, a physically based model to estimate ET from a water balance, and an event driven phenology model (EDPM), where the EDPM is an empirically derived crop specific model capable of producing seasonal trajectories of canopy attributes. In this experiment, the scheme was deployed in a spatially explicit manner within the croplands of the Northern Great Plains. The evaluation was carried out using 2007-2009 land surface forcing data from the North American Land Data Assimilation System (NLDAS) and crop maps derived from remotely sensed data of NASA's Moderate Resolution Imaging Spectroradiometer (MODIS). We compared the canopy parameters produced by the phenology model with normalized difference vegetation index (NDVI) data derived from the MODIS nadir bi-directional reflectance distribution function (BRDF) adjusted reflectance (NBAR) product. The expectations of the EDPM performance in prognostic mode were met, producing determination coefficient (r2) of 0.8 +/-.0.15. Model estimates of NDVI yielded root mean square error (RMSE) of 0.1 +/-.0.035 for the entire study area. Retrospective correction of canopy dynamics with MODIS NDVI brought the errors down to just below 10% of observed data range. The ET estimates produced by the coupled scheme were compared with ones from the MODIS land product suite. The expected r2=0.7 +/-.15 and RMSE = 11.2 +/-.4 mm per 8 days were met and even exceeded by the coupling scheme0 functioning in both prognostic and retrospective modes. Minor setbacks of the EDPM and VegET performance (r2 about 0.5 and additional 30 % of RMSR) were found on the peripheries of the study area and attributed to the insufficient EDPM training and to spatially varying accuracy of crop maps. Overall the experiment provided sufficient evidence of soundness and robustness of the EDPM and VegET coupling scheme, assuring its potential for spatially explicit applications.

First results from the International Urban Energy Balance Model Comparison: Model Complexity

NASA Astrophysics Data System (ADS)

Blackett, M.; Grimmond, S.; Best, M.

2009-04-01

A great variety of urban energy balance models has been developed. These vary in complexity from simple schemes that represent the city as a slab, through those which model various facets (i.e. road, walls and roof) to more complex urban forms (including street canyons with intersections) and features (such as vegetation cover and anthropogenic heat fluxes). Some schemes also incorporate detailed representations of momentum and energy fluxes distributed throughout various layers of the urban canopy layer. The models each differ in the parameters they require to describe the site and the in demands they make on computational processing power. Many of these models have been evaluated using observational datasets but to date, no controlled comparisons have been conducted. Urban surface energy balance models provide a means to predict the energy exchange processes which influence factors such as urban temperature, humidity, atmospheric stability and winds. These all need to be modelled accurately to capture features such as the urban heat island effect and to provide key information for dispersion and air quality modelling. A comparison of the various models available will assist in improving current and future models and will assist in formulating research priorities for future observational campaigns within urban areas. In this presentation we will summarise the initial results of this international urban energy balance model comparison. In particular, the relative performance of the models involved will be compared based on their degree of complexity. These results will inform us on ways in which we can improve the modelling of air quality within, and climate impacts of, global megacities. The methodology employed in conducting this comparison followed that used in PILPS (the Project for Intercomparison of Land-Surface Parameterization Schemes) which is also endorsed by the GEWEX Global Land Atmosphere System Study (GLASS) panel. In all cases, models were run offline to ensure no feedback to larger scale conditions within the modelling domain. Initially, participants were issued with just forcing data from an unknown urban site (termed "Alpha"); in subsequent stages, further details of the site were provided. Results from each stage, for each participating model, were then compared using a variety of statistical and graphical techniques. * The EGU2009-5713 Team: C.S.B. Grimmond1, M. Blackett1, M. Best2 and J. Barlow3and J.-J. Baik4, S. Belcher3, S. Bohnenstengel3, I. Calmet5, F. Chen6, A. Dandou7, K. Fortuniak8, M. Gouvea1, R. Hamdi9, M. Hendry2, H. Kondo10, S. Krayenhoff11, S. H. Lee4, T. Loridan1, A. Martilli12, S. Miao13, K. Oleson6, G. Pigeon14, A. Porson2,3, F. Salamanca12, L. Shashua-Bar15, G.-J. Steeneveld16, M. Tombrou7, J. Voogt17, N. Zhang18. 1King's College London, UK, 2UK Met Office, UK, 3University of Reading, UK, 4Seoul National University, Korea, 5Ecole Centrale de Nantes, France, 6National Center for Atmospheric Research, USA, 7University of Athens, Greece, 8University of Ł ódź , Poland, 9Royal Meteorological Institute, Belgium, 10National Institute of Advanced Industrial Science and Technology, Japan, 11University of British Columbia, Canada, 12CIEMAT, Spain, 13IUM, CMA, China, 14Meteo France, France, 15Ben Gurion University, Israel, 16Wageningen University, Netherlands, 17University of Western Ontario, Canada, 18Nanjing University, China.

The implementation of biofiltration systems, rainwater tanks and urban irrigation in a single-layer urban canopy model

NASA Astrophysics Data System (ADS)

Demuzere, Matthias; Coutts, Andrew; Goehler, Maren; Broadbent, Ashley; Wouters, Hendrik; van Lipzig, Nicole; Gebert, Luke

2015-04-01

Urban vegetation is generally considered as a key tool to modify the urban energy balance through enhanced evapotranspiration (ET). Given that vegetation is most effective when it is healthy, stormwater harvesting and retention strategies (such as water sensitive urban design) could be used to support vegetation and promote ET. This study presents the implementation of a vegetated lined bio-filtration system (BFS) combined with a rainwater tank (RWT) and urban irrigation system in the single-layer urban canopy model Community Land Model-Urban. Runoff from roof and impervious road surface fractions is harvested and used to support an adequate soil moisture level for vegetation in the BFS. In a first stage, modelled soil moisture dynamics are evaluated and found reliable compared to observed soil moisture levels from biofiltration pits in Smith Street, Melbourne (Australia). Secondly, the impact of BFS, RWT and urban irrigation on ET is illustrated for a two-month period in 2012 using varying characteristics for all components. Results indicate that (i) a large amount of stormwater is potentially available for indoor and outdoor water demands, including irrigation of urban vegetation, (ii) ET from the BFS is an order of magnitude larger compared to the contributions from the impervious surfaces, even though the former only covers 10% of the surface fraction and (iii) attention should be paid to the cover fraction and soil texture of the BFS, size of the RWT and the surface fractions contributing to the collection of water in the RWT. Overall, this study reveals that this model development can effectuate future research with state-of-the-art urban climate models to further explore the benefits of vegetated biofiltration systems as a water sensitive urban design tool optimised with an urban irrigation system to maintain healthy vegetation.

Development of an Urban Multilayer Radiation Scheme and Its Application to the Urban Surface Warming Potential

NASA Astrophysics Data System (ADS)

Aoyagi, Toshinori; Takahashi, Shunji

2012-02-01

To investigate how a three-dimensional structure such as an urban canyon can affect urban surface warming, we developed an urban multilayer radiation scheme. The complete consideration of multiple scattering of shortwave and longwave radiation using the radiosity method is an important feature of the present scheme. A brief description of this scheme is presented, followed by evaluations that compare its results with observations of the effective albedo and radiative temperature for urban blocks. Next, we calculate the urban surface warming potential (USWP), defined as the difference between the daily mean radiative temperature of urban surfaces (which are assumed to be black bodies), including their canyon effects and the daily mean temperature of a flat surface with the same material properties, under a radiative equilibrium state. Assuming standard material properties (albedo and emissivity of 0.4 and 0.9, respectively), we studied the sensitivity of the USWP to various aspect ratios of building heights to road widths. The results show that the temporally-averaged surface temperature of an urban area can be higher than that of a flat surface. In addition, we determined the overestimation of the effective temperature of urban surfaces induced by the overestimation of the radiation distribution to the walls when one uses a single-layer scheme for urban block arrays that have a low sky-view factor less than around 0.5.

Strategic guidelines for street canyon geometry to achieve sustainable street air quality—part II: multiple canopies and canyons

NASA Astrophysics Data System (ADS)

Chan, Andy T.; Au, William T. W.; So, Ellen S. P.

The flow field and pollutant dispersion characteristics in a three-dimensional urban street canyon are investigated for various building array geometries. The street canyon in consideration is located in a multi-canopy building array that is similar to realistic estate situations. The pollutant dispersion characteristics are studied for various canopy aspect ratios, namely: the canyon height to width ratio, canyon length to height ratio, canyon breadth ratio and crossroad locations are studied. A three-dimensional field-size canyon has been analysed through numerical simulations using k- ɛ turbulence model. As expected, the wind flow and mode of pollutant dispersion is strongly dependent on the various flow geometric configurations and that the results can be different from that of a single canyon system. For example, it is found that the pollutant retention value is minimum when the canyon height-to-width ratio is approximately 0.8, or that the building height ratio is 0.5. Various rules of thumbs on urban canyon geometry have been established for good pollutant dispersion.

Assessing urban forest effects and values, Washington, D.C.'s urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2006-01-01

An analysis of trees in Washington, D.C. reveals that this city has about 1,928,000 trees with canopies that cover 28.6 percent of the area. The most common tree species are American beech, red maple, and boxelder. The urban forest currently store about 526,000 tons of carbon valued at $9.7 million. In addition, these trees remove about 16,200 tons of carbon per year...

Assessing urban forest effects and values, New York City's urban forest

Treesearch

David J. Nowak; Robert E., III Hoehn; Daniel E. Crane; Jack C. Stevens; Jeffrey T. Walton

2007-01-01

An analysis of trees in New York City reveals that this city has about 5.2 million trees with canopies that cover 20.9 percent of the area. The most common tree species are tree of heaven, black cherry, and sweetgum. The urban forest currently stores about 1.35 million tons of carbon valued at $24.9 million. In addition, these trees remove about 42,300 tons of carbon...

Estimating the relationship between urban 3D morphology and land surface temperature using airborne LiDAR and Landsat-8 Thermal Infrared Sensor data

NASA Astrophysics Data System (ADS)

Lee, J. H.

2015-12-01

Urban forests are known for mitigating the urban heat island effect and heat-related health issues by reducing air and surface temperature. Beyond the amount of the canopy area, however, little is known what kind of spatial patterns and structures of urban forests best contributes to reducing temperatures and mitigating the urban heat effects. Previous studies attempted to find the relationship between the land surface temperature and various indicators of vegetation abundance using remote sensed data but the majority of those studies relied on two dimensional area based metrics, such as tree canopy cover, impervious surface area, and Normalized Differential Vegetation Index, etc. This study investigates the relationship between the three-dimensional spatial structure of urban forests and urban surface temperature focusing on vertical variance. We use a Landsat-8 Thermal Infrared Sensor image (acquired on July 24, 2014) to estimate the land surface temperature of the City of Sacramento, CA. We extract the height and volume of urban features (both vegetation and non-vegetation) using airborne LiDAR (Light Detection and Ranging) and high spatial resolution aerial imagery. Using regression analysis, we apply empirical approach to find the relationship between the land surface temperature and different sets of variables, which describe spatial patterns and structures of various urban features including trees. Our analysis demonstrates that incorporating vertical variance parameters improve the accuracy of the model. The results of the study suggest urban tree planting is an effective and viable solution to mitigate urban heat by increasing the variance of urban surface as well as evaporative cooling effect.

Constructing an Urban Population Model for Medical Insurance Scheme Using Microsimulation Techniques

PubMed Central

Xiong, Linping; Zhang, Lulu; Tang, Weidong; Ma, Yuqin

2012-01-01

China launched a pilot project of medical insurance reform in 79 cities in 2007 to cover urban nonworking residents. An urban population model was created in this paper for China's medical insurance scheme using microsimulation model techniques. The model made it clear for the policy makers the population distributions of different groups of people, the potential urban residents entering the medical insurance scheme. The income trends of units of individuals and families were also obtained. These factors are essential in making the challenging policy decisions when considering to balance the long-term financial sustainability of the medical insurance scheme. PMID:22481973

Prioritizing preferable locations for increasing urban tree canopy in New York City

Treesearch

Dexter Locke; J. Morgan Grove; Jacqueline W.T. Lu; Austin Troy; Jarlath P.M. O' Neil-Dunne; Brian Beck

2010-01-01

This paper presents a set of Geographic Information System (GIS) methods for identifying and prioritizing tree planting sites in urban environments. It uses an analytical approach created by a University of Vermont service-learning class called "GIS Analysis of New York City's Ecology" that was designed to provide research support to the MillionTreesNYC...

Three-Dimensional Mapping of Air Flow at an Urban Canyon Intersection

NASA Astrophysics Data System (ADS)

Carpentieri, Matteo; Robins, Alan G.; Baldi, Sandro

2009-11-01

In this experimental work both qualitative (flow visualisation) and quantitative (laser Doppler anemometry) methods were applied in a wind tunnel in order to describe the complex three-dimensional flow field in a real environment (a street canyon intersection). The main aim was an examination of the mean flow, turbulence and flow pathlines characterising a complex three-dimensional urban location. The experiments highlighted the complexity of the observed flows, particularly in the upwind region of the intersection. In this complex and realistic situation some details of the upwind flow, such as the presence of two tall towers, play an important role in defining the flow field within the intersection, particularly at roof level. This effect is likely to have a strong influence on the mass exchange mechanism between the canopy flow and the air aloft, and therefore the distribution of pollutants. This strong interaction between the flows inside and outside the urban canopy is currently neglected in most state-of-the-art local scale dispersion models.

Differences in BVOC oxidation and SOA formation above and below the forest canopy

NASA Astrophysics Data System (ADS)

Schulze, Benjamin C.; Wallace, Henry W.; Flynn, James H.; Lefer, Barry L.; Erickson, Matt H.; Jobson, B. Tom; Dusanter, Sebastien; Griffith, Stephen M.; Hansen, Robert F.; Stevens, Philip S.; VanReken, Timothy; Griffin, Robert J.

2017-02-01

Gas-phase biogenic volatile organic compounds (BVOCs) are oxidized in the troposphere to produce secondary pollutants such as ozone (O3), organic nitrates (RONO2), and secondary organic aerosol (SOA). Two coupled zero-dimensional models have been used to investigate differences in oxidation and SOA production from isoprene and α-pinene, especially with respect to the nitrate radical (NO3), above and below a forest canopy in rural Michigan. In both modeled environments (above and below the canopy), NO3 mixing ratios are relatively small (< 0.5 pptv); however, daytime (08:00-20:00 LT) mixing ratios below the canopy are 2 to 3 times larger than those above. As a result of this difference, NO3 contributes 12 % of total daytime α-pinene oxidation below the canopy while only contributing 4 % above. Increasing background pollutant levels to simulate a more polluted suburban or peri-urban forest environment increases the average contribution of NO3 to daytime below-canopy α-pinene oxidation to 32 %. Gas-phase RONO2 produced through NO3 oxidation undergoes net transport upward from the below-canopy environment during the day, and this transport contributes up to 30 % of total NO3-derived RONO2 production above the canopy in the morning (˜ 07:00). Modeled SOA mass loadings above and below the canopy ultimately differ by less than 0.5 µg m-3, and extremely low-volatility organic compounds dominate SOA composition. Lower temperatures below the canopy cause increased partitioning of semi-volatile gas-phase products to the particle phase and up to 35 % larger SOA mass loadings of these products relative to above the canopy in the model. Including transport between above- and below-canopy environments increases above-canopy NO3-derived α-pinene RONO2 SOA mass by as much as 45 %, suggesting that below-canopy chemical processes substantially influence above-canopy SOA mass loadings, especially with regard to monoterpene-derived RONO2.

Seasonal albedo of an urban/rural landscape from satellite observations

NASA Technical Reports Server (NTRS)

Brest, Christopher L.

1987-01-01

Using data from 27 calibrated Landsat observations of the Hartford, Connecticut area, the spatial distribution and seasonal variation of surface reflectance and albedo were examined. Mean values of visible reflectance, near-IR reflectance, and albedo are presented (for both snow-free and snow-cover observations) according to 14 land use/land cover categories. A diversity of albedo values was found to exist in this type of environment, associated with land cover. Many land-cover categories display a seasonal dependence, with intracategory seasonal differences being of comparable magnitude to intercategory differences. Key factors in determining albedo (and its seasonal dynamics) are the presence or absence of vegetation and the canopy structure. Snow-cover/snow-free differences range from a few percent (for urban land covers) to over 40 percent (for low-canopy vegetation).

Remote Sensing Characterization of the Urban Landscape for Improvement of Air Quality Modeling

NASA Technical Reports Server (NTRS)

Quattrochi, Dale A.; Estes, Maurice G., Jr.; Khan, Maudood

2005-01-01

The urban landscape is inherently complex and this complexity is not adequately captured in air quality models, particularly the Community Multiscale Air Quality (CMAQ) model that is used to assess whether urban areas are in attainment of EPA air quality standards, primarily for ground level ozone. This inadequacy of the CMAQ model to sufficiently respond to the heterogeneous nature of the urban landscape can impact how well the model predicts ozone pollutant levels over metropolitan areas and ultimately, whether cities exceed EPA ozone air quality standards. We are exploring the utility of high-resolution remote sensing data and urban growth projections as improved inputs to the meteorology component of the CMAQ model focusing on the Atlanta, Georgia metropolitan area as a case study. These growth projections include "business as usual" and "smart growth" scenarios out to 2030. The growth projections illustrate the effects of employing urban heat island mitigation strategies, such as increasing tree canopy and albedo across the Atlanta metro area, in moderating ground-level ozone and air temperature, compared to "business as usual" simulations in which heat island mitigation strategies are not applied. The National Land Cover Dataset at 30m resolution is being used as the land use/land cover input and aggregated to the 4km scale for the MM5 mesoscale meteorological model and the (CMAQ) modeling schemes. Use of these data has been found to better characterize low densityhburban development as compared with USGS 1 km land use/land cover data that have traditionally been used in modeling. Air quality prediction for fiture scenarios to 2030 is being facilitated by land use projections using a spatial growth model. Land use projections were developed using the 2030 Regional Transportation Plan developed by the Atlanta Regional Commission, the regional planning agency for the area. This allows the state Environmental Protection agency to evaluate how these transportation plans will affect fbture air quality.

Exotic weeds and fluctuating microclimate can constrain native plant regeneration in urban forest restoration.

PubMed

Wallace, K J; Laughlin, Daniel C; Clarkson, Bruce D

2017-06-01

Restoring forest structure and composition is an important component of urban land management, but we lack clear understanding of the mechanisms driving restoration success. Here we studied two indicators of restoration success in temperate rainforests: native tree regeneration and epiphyte colonization. We hypothesized that ecosystem properties such as forest canopy openness, abundance of exotic herbaceous weeds, and the microclimate directly affect the density and diversity of native tree seedlings and epiphytes. Relationships between environmental conditions and the plant community were investigated in 27 restored urban forests spanning 3-70 years in age and in unrestored and remnant urban forests. We used structural equation modelling to determine the direct and indirect drivers of native tree regeneration and epiphyte colonization in the restored forests. Compared to remnant forest, unrestored forest had fewer native canopy tree species, significantly more light reaching the forest floor annually, and higher exotic weed cover. Additionally, epiphyte density was lower and native tree regeneration density was marginally lower in the unrestored forests. In restored forests, light availability was reduced to levels found in remnant forests within 20 years of restoration planting, followed shortly thereafter by declines in herbaceous exotic weeds and reduced fluctuation of relative humidity and soil temperatures. Contrary to expectations, canopy openness was only an indirect driver of tree regeneration and epiphyte colonization, but it directly regulated weed cover and microclimatic fluctuations, both of which directly drove the density and richness of regeneration and epiphyte colonization. Epiphyte density and diversity were also positively related to forest basal area, as large trees provide physical habitat for colonization. These results imply that ecosystem properties change predictably after initial restoration plantings, and that reaching critical thresholds in some ecosystem properties makes conditions suitable for the regeneration of late successional species, which is vital for restoration success and long-term ecosystem sustainability. Abiotic and biotic conditions that promote tree regeneration and epiphyte colonization will likely be present in forests with a basal area ≥27 m 2 /ha. We recommend that urban forest restoration plantings be designed to promote rapid canopy closure to reduce light availability, suppress herbaceous weeds, and stabilize the microclimate. © 2017 by the Ecological Society of America.

Evaluation of an urban canopy model in a tropical city: the role of tree evapotranspiration

NASA Astrophysics Data System (ADS)

Liu, Xuan; Li, Xian-Xiang; Harshan, Suraj; Roth, Matthias; Velasco, Erik

2017-09-01

A single layer urban canopy model (SLUCM) with enhanced hydrologic processes, is evaluated in a tropical city, Singapore. The evaluation was performed using an 11 month offline simulation with the coupled Noah land surface model/SLUCM over a compact low-rise residential area. Various hydrological processes are considered, including anthropogenic latent heat release, and evaporation from impervious urban facets. Results show that the prediction of energy fluxes, in particular latent heat flux, is improved when these processes were included. However, the simulated latent heat flux is still underestimated by ∼40%. Considering Singapore’s high green cover ratio, the tree evapotranspiration process is introduced into the model, which significantly improves the simulated latent heat flux. In particular, the systematic error of the model is greatly reduced, and becomes lower than the unsystematic error in some seasons. The effect of tree evapotranspiration on the urban surface energy balance is further demonstrated during an unusual dry spell. The present study demonstrates that even at sites with relatively low (11%) tree coverage, ignoring evapotranspiration from trees may cause serious underestimation of the latent heat flux and atmospheric humidity. The improved model is also transferable to other tropical or temperate regions to study the impact of tree evapotranspiration on urban climate.

Albedo, Land Cover, and Daytime Surface Temperature Variation Across an Urbanized Landscape

NASA Astrophysics Data System (ADS)

Trlica, A.; Hutyra, L. R.; Schaaf, C. L.; Erb, A.; Wang, J. A.

2017-11-01

Land surface albedo is a key parameter controlling the local energy budget, and altering the albedo of built surfaces has been proposed as a tool to mitigate high near-surface temperatures in the urban heat island. However, most research on albedo in urban landscapes has used coarse-resolution data, and few studies have attempted to relate albedo to other urban land cover characteristics. This study provides an empirical description of urban summertime albedo using 30 m remote sensing measurements in the metropolitan area around Boston, Massachusetts, relating albedo to metrics of impervious cover fraction, tree canopy coverage, population density, and land surface temperature (LST). At 30 m spatial resolution, median albedo over the study area (excluding open water) was 0.152 (0.112-0.187). Trends of lower albedo with increasing urbanization metrics and temperature emerged only after aggregating data to 500 m or the boundaries of individual towns, at which scale a -0.01 change in albedo was associated with a 29 (25-35)% decrease in canopy cover, a 27 (24-30)% increase in impervious cover, and an increase in population from 11 to 386 km-2. The most intensively urbanized towns in the region showed albedo up to 0.035 lower than the least urbanized towns, and mean mid-morning LST 12.6°C higher. Trends in albedo derived from 500 m Moderate Resolution Imaging Spectroradiometer (MODIS) measurements were comparable, but indicated a strong contribution of open water at this coarser resolution. These results reveal linkages between albedo and urban land cover character, and offer empirical context for climate resilient planning and future landscape functional changes with urbanization.

The urban forests of Philadelphia

Treesearch

David J. Nowak; Allison R. Bodine; Robert Hoehn; Alexis Ellis; Sarah C. Low; Lara A. Roman; Jason G. Henning; Emily Stephan; Tom Taggert; Ted Endreny

2016-01-01

An analysis of the urban forest in Philadelphia, Pennsylvania, reveals that this city has an estimated 2.9 million trees (encompassing all woody plants greater than 1 inch diameter at breast height [d.b.h]) with tree canopy that covers 20 percent of the city. The most common tree species are spicebush, black cherry, ash, tree-of-heaven, and boxelder, but the most...

Austin's Urban Forest, 2014

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Christopher B. Edgar; Dudley R. Hartel; Tonya W. Lister; Thomas J. Brandeis

2016-01-01

An analysis of the urban forest in Austin, Texas, reveals that this area has an estimated 33.8 million trees with tree canopy that covers 30.8 percent of the city. The most common tree species are Ashe juniper, cedar elm, live oak, sugarberry, and Texas persimmon. Trees in Austin currently store about 1.9 million tons of carbon (7.0 million tons of carbon dioxide [CO...

An evaluation of the performance of a WRF multi-physics ensemble for heatwave events over the city of Melbourne in southeast Australia

NASA Astrophysics Data System (ADS)

Imran, H. M.; Kala, J.; Ng, A. W. M.; Muthukumaran, S.

2018-04-01

Appropriate choice of physics options among many physics parameterizations is important when using the Weather Research and Forecasting (WRF) model. The responses of different physics parameterizations of the WRF model may vary due to geographical locations, the application of interest, and the temporal and spatial scales being investigated. Several studies have evaluated the performance of the WRF model in simulating the mean climate and extreme rainfall events for various regions in Australia. However, no study has explicitly evaluated the sensitivity of the WRF model in simulating heatwaves. Therefore, this study evaluates the performance of a WRF multi-physics ensemble that comprises 27 model configurations for a series of heatwave events in Melbourne, Australia. Unlike most previous studies, we not only evaluate temperature, but also wind speed and relative humidity, which are key factors influencing heatwave dynamics. No specific ensemble member for all events explicitly showed the best performance, for all the variables, considering all evaluation metrics. This study also found that the choice of planetary boundary layer (PBL) scheme had largest influence, the radiation scheme had moderate influence, and the microphysics scheme had the least influence on temperature simulations. The PBL and microphysics schemes were found to be more sensitive than the radiation scheme for wind speed and relative humidity. Additionally, the study tested the role of Urban Canopy Model (UCM) and three Land Surface Models (LSMs). Although the UCM did not play significant role, the Noah-LSM showed better performance than the CLM4 and NOAH-MP LSMs in simulating the heatwave events. The study finally identifies an optimal configuration of WRF that will be a useful modelling tool for further investigations of heatwaves in Melbourne. Although our results are invariably region-specific, our results will be useful to WRF users investigating heatwave dynamics elsewhere.

[Species composition and spatial structure of plants in urban parks of Beijing].

PubMed

Zhao, Juan-Juan; Ouyang, Zhi-Yun; Zheng, Hua; Xu, Wei-Hua; Wang, Xiao-Ke

2009-02-01

By the method of stratified random sampling, the species composition and spatial structure of the plants in 53 parks in Beijing urban area were investigated, aimed to provide basic information for the protection of plant diversity in the parks and the management of the parks. A total of 492 plant species belong to 96 families and 283 genera were recorded. Based on the data of 21 investigation items about the trees, shrubs, and grasses in the study area and related statistical analyses, the plant structural patterns commonly seen in the green space of the parks of Beijing urban area were introduced. Among the plants in the parks, native species occupied 53.86% of the total. The chorological composition of the genera embraced broad kinds of geographical elements in China, and the predominance of dominant plants was remarkable. In most green patches of the parks, herbaceous species were more abundant and had higher coverage, shrubs had relatively low coverage and were less beneath tree canopy, and trees and shrubs had lower species richness and density. The canopy breadth and the diameter of breast height of trees as well as the breadth of shrubs and the heights of trees and shrubs were basically at the second grade, but the canopy structure of the trees were better, with good conditions of sunlight and growth. The crown missing of the shrubs was relatively low. It was suggested from correlation analyses and document survey of Beijing parks construction history that park landscape design, alien species introduction; and cultivation management were the main factors affecting the species composition and spatial structure of the plants in Beijing urban parks.

Biological and environmental controls on tree transpiration in a suburban landscape

NASA Astrophysics Data System (ADS)

Peters, Emily B.; McFadden, Joseph P.; Montgomery, Rebecca A.

2010-12-01

Tree transpiration provides a variety of ecosystem services in urban areas, including amelioration of urban heat island effects and storm water management. Tree species vary in the magnitude and seasonality of transpiration owing to differences in physiology, response to climate, and biophysical characteristics, thereby complicating efforts to manage evapotranspiration at city scales. We report sap flux measurements during the 2007 and 2008 growing seasons for dominant tree species in a suburban neighborhood of Minneapolis-Saint Paul, Minnesota, USA. Evergreen needleleaf trees had significantly higher growing season means and annual transpiration per unit canopy area (1.90 kg H2O m-2 d-1 and 307 kg H2O m-2 yr-1, respectively) than deciduous broadleaf trees (1.11 kg H2O m-2 d-1 and 153 kg H2O m-2 yr-1, respectively) because of a smaller projected canopy area (31.1 and 73.6 m2, respectively), a higher leaf area index (8.8 and 5.5 m2 m-2, respectively), and a longer growth season (8 and 4 months, respectively). Measurements also showed patterns consistent with the species' differences in xylem anatomy (conifer, ring porous, and diffuse porous). As the growing season progressed, conifer and diffuse porous genera had increased stomatal regulation to high vapor pressure deficit, while ring porous genera maintained greater and more constant stomatal regulation. These results suggest that evaporative responses to climate change in urban ecosystems will depend in part on species composition. Overall, plant functional type differences in canopy structure and growing season length were most important in explaining species' differences in midsummer and annual transpiration, offering an approach to predicting the evapotranspiration component of urban water budgets.

Investigating the Potential of Land Use Modifications to Mitigate the Respiratory Health Impacts of NO2: A Case Study in the Portland-Vancouver Metropolitan Area

NASA Astrophysics Data System (ADS)

Rao, Meenakshi

The health impacts of urban air pollution are a growing concern in our rapidly urbanizing world. Urban air pollutants show high intra-urban spatial variability linked to urban land use and land cover (LULC). This correlation of air pollutants with LULC is widely recognized; LULC data is an integral input into a wide range of models, especially land use regression models developed by epidemiologists to study the impact of air pollution on human health. Given the demonstrated links between LULC and urban air pollution, and between urban air pollution and health, an interesting question arises: what is the potential of LULC modifications to mitigate the health impacts of urban air pollution? In this dissertation we assess the potential of LULC modifications to mitigate the health impacts of NO2, a respiratory irritant and strong marker for combustion-related air pollution, in the Portland-Vancouver metropolitan area in northwestern USA. We begin by measuring summer and winter NO2 in the area using a spatially dense network of passive NO 2 samplers. We next develop an annual average model for NO2 based on the observational data, using random forest--for the first time in the realm of urban air pollution--to disentangle the effects of highly correlated LULC variables on ambient NO2 concentrations. We apply this random forest (LURF) model to a 200m spatial grid covering the study area, and use this 200m LURF model to quantify the effect of different urban land use categories on ambient concentrations of NO2. Using the changes in ambient NO2 concentrations resulting from land use modifications as input to BenMAP (a health benefits assessment tool form the US EPA), we assess the NO2-related health impact associated with each land use category and its modifications. We demonstrate how the LURF model can be used to assess the respiratory health benefits of competing land use modifications, including city-wide and local-scale mitigation strategies based on modifying tree canopy and vehicle miles traveled (VMT). Planting trees is a common land cover modification strategy undertaken by cities to reduce air pollution. Statistical models such as LUR and LURF demonstrate a correlation between tree cover and reduced air pollution, but they cannot demonstrate causation. Hence, we run the atmospheric chemistry and transport model CMAQ to examine to what extent the dry deposition mechanism can explain the reduction of NO2 which statistical models associate with tree canopy. Results from our research indicate that even though the Portland-Vancouver area is in compliance with the US EPA NO2 standards, ambient concentrations of NO2 still create an annual health burden of at least 40 million USD. Our model suggests that NO2 associated with high intensity development and VMT may be creating an annual health burden of 7 million and 3.3 million USD respectively. Existing tree canopy, on the other hand, is associated with an annual health benefit of 1.4 million USD. LULC modifications can mitigate some fraction of this health burden. A 2% increase in tree canopy across the study area may reduce incidence rates of asthma exacerbation by as much as 7%. We also find that increasing tree canopy is a more effective strategy than reducing VMT in terms of mitigating the health burden of NO 2. CMAQ indicates that the amount of NO2 removed by dry deposition is an order of magnitude smaller than that predicted by our statistical model. About one-third of the difference can be explained by the lower NO2 values predicted by CMAQ, and one-third may be attributable to parameterization of stomatal uptake.

A comprehensive approach for the simulation of the Urban Heat Island effect with the WRF/SLUCM modeling system: The case of Athens (Greece)

NASA Astrophysics Data System (ADS)

Giannaros, Christos; Nenes, Athanasios; Giannaros, Theodore M.; Kourtidis, Konstantinos; Melas, Dimitrios

2018-03-01

This study presents a comprehensive modeling approach for simulating the spatiotemporal distribution of urban air temperatures with a modeling system that includes the Weather Research and Forecasting (WRF) model and the Single-Layer Urban Canopy Model (SLUCM) with a modified treatment of the impervious surface temperature. The model was applied to simulate a 3-day summer heat wave event over the city of Athens, Greece. The simulation, using default SLUCM parameters, is capable of capturing the observed diurnal variation of urban temperatures and the Urban Heat Island (UHI) in the greater Athens Area (GAA), albeit with systematic biases that are prominent during nighttime hours. These biases are particularly evident over low-intensity residential areas, and they are associated with the surface and urban canopy properties representing the urban environment. A series of sensitivity simulations unravels the importance of the sub-grid urban fraction parameter, surface albedo, and street canyon geometry in the overall causation and development of the UHI effect. The sensitivities are then used to determine optimal values of the street canyon geometry, which reproduces the observed temperatures throughout the simulation domain. The optimal parameters, apart from considerably improving model performance (reductions in mean temperature bias from 0.30 °C to 1.58 °C), are also consistent with actual city building characteristics - which gives confidence that the model set-up is robust, and can be used to study the UHI in the GAA in the anticipated warmer conditions in the future.

FORest canopy atmosphere transfer (FORCAsT) 1.0: a 1-D model of biosphere-atmosphere chemical exchange

NASA Astrophysics Data System (ADS)

Ashworth, K.; Chung, S. H.; Griffin, R. J.; Chen, J.; Forkel, R.; Bryan, A. M.; Steiner, A. L.

2015-07-01

Biosphere-atmosphere interactions play a critical role in governing atmospheric composition, mediating the concentration of key species such as ozone and aerosol, thereby influencing air quality and climate. The exchange of reactive trace gases and their oxidation products (both gas and particle phase) is of particular importance in this process. The FORCAsT (FORest Canopy AtmoSphere Transfer) one-dimensional model is developed to study the emission, deposition, chemistry and transport of volatile organic compounds (VOCs) and their oxidation products in the atmosphere within and above the forest canopy. We include an equilibrium partitioning scheme, making FORCAsT one of the few canopy models currently capable of simulating the formation of secondary organic aerosols (SOA) from VOC oxidation in a forest environment. We evaluate the capability of FORCAsT to reproduce observed concentrations of key gas-phase species and report modeled SOA concentrations within and above a mixed forest at the University of Michigan Biological Station (UMBS) during the Community Atmosphere-Biosphere Interactions Experiment (CABINEX) field campaign in summer 2009. We examine the impact of two different gas-phase chemical mechanisms on modelled concentrations of short-lived primary emissions, such as isoprene and monoterpenes, and their oxidation products. While the two chemistry schemes perform similarly under high-NOx conditions, they diverge at the low levels of NOx at UMBS. We identify peroxy radical and alkyl nitrate chemistry as the key causes of the differences, highlighting the importance of this chemistry in understanding the fate of biogenic VOCs (bVOCs) for both the modelling and measurement communities.

FORest Canopy Atmosphere Transfer (FORCAsT) 1.0: a 1-D model of biosphere-atmosphere chemical exchange

NASA Astrophysics Data System (ADS)

Ashworth, K.; Chung, S. H.; Griffin, R. J.; Chen, J.; Forkel, R.; Bryan, A. M.; Steiner, A. L.

2015-11-01

Biosphere-atmosphere interactions play a critical role in governing atmospheric composition, mediating the concentrations of key species such as ozone and aerosol, thereby influencing air quality and climate. The exchange of reactive trace gases and their oxidation products (both gas and particle phase) is of particular importance in this process. The FORCAsT (FORest Canopy Atmosphere Transfer) 1-D model is developed to study the emission, deposition, chemistry and transport of volatile organic compounds (VOCs) and their oxidation products in the atmosphere within and above the forest canopy. We include an equilibrium partitioning scheme, making FORCAsT one of the few canopy models currently capable of simulating the formation of secondary organic aerosols (SOAs) from VOC oxidation in a forest environment. We evaluate the capability of FORCAsT to reproduce observed concentrations of key gas-phase species and report modeled SOA concentrations within and above a mixed forest at the University of Michigan Biological Station (UMBS) during the Community Atmosphere-Biosphere Interactions Experiment (CABINEX) field campaign in the summer of 2009. We examine the impact of two different gas-phase chemical mechanisms on modelled concentrations of short-lived primary emissions, such as isoprene and monoterpenes, and their oxidation products. While the two chemistry schemes perform similarly under high-NOx conditions, they diverge at the low levels of NOx at UMBS. We identify peroxy radical and alkyl nitrate chemistry as the key causes of the differences, highlighting the importance of this chemistry in understanding the fate of biogenic VOCs (bVOCs) for both the modelling and measurement communities.

Impact of urbanization-related land use land cover changes and urban morphology changes on the urban heat island phenomenon.

PubMed

Zhou, Xuefan; Chen, Hong

2018-04-24

Urban growth and development caused by urbanization influence the urban heat island (UHI) phenomenon. With the rapid development of urbanization, China's major cities are facing more serious climate change problems, especially the UHI phenomenon. Proper planning and urban design of compact cities may improve the ventilation of street canyons and change the heat balance in the urban canopy and thus mitigate the UHI phenomenon. The aim of this study is to evaluate and discuss the mitigation of UHI with different types of land-use and land-cover (LUCC), as well as different development patterns for compact cities. To this end, we applied the weather research and forecasting model (WRF) with urban canopy model (WRF/UCM) in this study. To evaluate the impact of LUCC changes on the UHI, we set 2 cases based on land use and land cover statistical data from 1965 and 2008 of Wuhan. Also, to evaluate the impact of urban morphology changes on the UHI, we designed 2 hypothetical cases based on 2 different urban developing patterns, one is high rise case and another is high density case, to simulate the impact of urban morphology on the UHI. As for the results of this study, with different LUCC of 1965 and 2008, UHI intensity of Wuhan increased by 0.2 °C-0.4 °C in average. Moreover, the critical wind speed which can mitigate UHI of case 1965 is much lower than case 2008. With different urban morphology, the high-rise case may lead to lower UHI intensity at the pedestrian level due to the shading effects of high-rise buildings. However, the critical value of wind speed in the high-rise case was almost 1.5-2 times greater than that of the high-density case, which illustrates the reduced possibility of mitigating the UHI phenomenon for high-rise buildings in Wuhan City. Copyright © 2018 Elsevier B.V. All rights reserved.

Effects of trees on mean wind, turbulence and momentum exchange within and above a real urban environment

NASA Astrophysics Data System (ADS)

Giometto, M. G.; Christen, A.; Egli, P. E.; Schmid, M. F.; Tooke, R. T.; Coops, N. C.; Parlange, M. B.

2017-08-01

Large-eddy simulations (LES) are used to gain insight into the effects of trees on turbulence, aerodynamic parameters, and momentum transfer rates characterizing the atmosphere within and above a real urban canopy. Several areas are considered that are part of a neighborhood in the city of Vancouver, BC, Canada where a small fraction of trees are taller than buildings. In this area, eight years of continuous wind and turbulence measurements are available from a 30 m meteorological tower. Data from airborne light detection and ranging (LiDAR) are used to represent both buildings and vegetation at the LES resolution. In the LES algorithm, buildings are accounted through an immersed boundary method, whereas vegetation is parameterized via a location-specific leaf area density. LES are performed including and excluding vegetation from the considered urban areas, varying wind direction and leaf area density. Surface roughness lengths (z0) from both LES and tower measurements are sensitive to the 0 ≤ LAI /λfb < 3 parameter, where LAI is the leaf area index and λfb is the frontal area fraction of buildings characterizing a given canopy. For instance, tower measurements predict a 19% seasonal increase in z0, slightly lower than the 27% increase featured by LES for the most representative canopy (leaves-off LAI / λfSUP>b = 0.74 , leaves-on LAI /λfb = 2.24). Removing vegetation from such a canopy would cause a dramatic drop of approximately 50% in z0 when compared to the reference summer value. The momentum displacement height (d) from LES also consistently increases as LAI / λfb increases, due in large part to the disproportionate amount of drag that the (few) relatively taller trees exert on the flow. LES and measurements both predict an increase in the ratio of turbulent to mean kinetic energy (TKE/MKE) at the tower sampling height going from winter to summer, and LES also show how including vegetation results in a more (positive) negatively skewed (horizontal) vertical velocity distribution - reflecting a more intermittent velocity field which favors sweep motions when compared to ejections. Within the urban canopy, the effects of trees are twofold: on one hand, they act as a direct momentum sink for the mean flow; on the other, they reduce downward turbulent transport of high-momentum fluid, significantly reducing the wind intensity at the heights where people live and buildings consume energy.

Validation of the Martilli's Urban Boundary Layer Scheme with measurements from two mid-latitude European cities

NASA Astrophysics Data System (ADS)

Hamdi, R.; Schayes, G.

2005-07-01

The Martilli's urban parameterization scheme is improved and implemented in a mesoscale model in order to take into account the typical effects of a real city on the air temperature near the ground and on the surface exchange fluxes. The mesoscale model is run on a single column using atmospheric data and radiation recorded above roof level as forcing. Here, the authors validate the Martilli's urban boundary layer scheme using measurements from two mid-latitude European cities: Basel, Switzerland and Marseilles, France. For Basel, the model performance is evaluated with observations of canyon temperature, surface radiation, and energy balance fluxes obtained during the Basel urban boundary layer experiment (BUBBLE). The results show that the urban parameterization scheme is able to reproduce the generation of the Urban Heat Island (UHI) effect over urban area and represents correctly most of the behavior of the fluxes typical of the city center of Basel, including the large heat uptake by the urban fabric and the positive sensible heat flux at night. For Marseilles, the model performance is evaluated with observations of surface temperature, canyon temperature, surface radiation, and energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) and its urban boundary layer (UBL) campaign. At both urban sites, vegetation cover is less than 20%, therefore, particular attention was directed to the ability of the Martilli's urban boundary layer scheme to reproduce the observations for the Marseilles city center, where the urban parameters and the synoptic forcing are totally different from Basel. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model correctly simulates the net radiation, canyon temperature, and the partitioning between the turbulent and storage heat fluxes.

High resolution urban morphology data for urban wind flow modeling

NASA Astrophysics Data System (ADS)

Cionco, Ronald M.; Ellefsen, Richard

The application of urban forestry methods and technologies to a number of practical problems can be further enhanced by the use and incorporation of localized, high resolution wind and temperature fields into their analysis methods. The numerical simulation of these micrometeorological fields will represent the interactions and influences of urban structures, vegetation elements, and variable terrain as an integral part of the dynamics of an urban domain. Detailed information of the natural and man-made components that make up the urban area is needed to more realistically model meteorological fields in urban domains. Simulating high resolution wind and temperatures over and through an urban domain utilizing detailed morphology data can also define and quantify local areas where urban forestry applications can contribute to better solutions. Applications such as the benefits of planting trees for shade purposes can be considered, planned, and evaluated for their impact on conserving energy and cooling costs as well as the possible reconfiguration or removal of trees and other barriers for improved airflow ventilation and similar processes. To generate these fields, a wind model must be provided, as a minimum, the location, type, height, structural silhouette, and surface roughness of these components, in order to account for the presence and effects of these land morphology features upon the ambient airflow. The morphology of Sacramento, CA has been characterized and quantified in considerable detail primarily for wind flow modeling, simulation, and analyses, but can also be used for improved meteorological analyses, urban forestry, urban planning, and other urban related activities. Morphology methods previously developed by Ellefsen are applied to the Sacramento scenario with a high resolution grid of 100 m × 100 m. The Urban Morphology Scheme defines Urban Terrain Zones (UTZ) according to how buildings and other urban elements are structured and placed with respect to each other. The urban elements within the 100 m × 100 m cells (one hectare) are further described and digitized as building height, building footprint (in percent), reflectivity of its roof, pitched roof or flat, building's long axis orientation, footprint of impervious surface and its reflectivity, footprint of canopy elements, footprint of woodlots, footprint of grass area, and footprint of water surface. A variety of maps, satellite images, low level aerial photographs, and street level photographs are the raw data used to quantify these urban properties. The final digitized morphology database resides in a spreadsheet ready for use on ordinary personal computers.

Flow adjustment inside homogeneous canopies after a leading edge – An analytical approach backed by LES

DOE PAGES

Kroniger, Konstantin; Banerjee, Tirtha; De Roo, Frederik; ...

2017-10-06

A two-dimensional analytical model for describing the mean flow behavior inside a vegetation canopy after a leading edge in neutral conditions was developed and tested by means of large eddy simulations (LES) employing the LES code PALM. The analytical model is developed for the region directly after the canopy edge, the adjustment region, where one-dimensional canopy models fail due to the sharp change in roughness. The derivation of this adjustment region model is based on an analytic solution of the two-dimensional Reynolds averaged Navier–Stokes equation in neutral conditions for a canopy with constant plant area density (PAD). The main assumptionsmore » for solving the governing equations are separability of the velocity components concerning the spatial variables and the neglection of the Reynolds stress gradients. These two assumptions are verified by means of LES. To determine the emerging model parameters, a simultaneous fitting scheme was applied to the velocity and pressure data of a reference LES simulation. Furthermore a sensitivity analysis of the adjustment region model, equipped with the previously calculated parameters, was performed varying the three relevant length, the canopy height ( h), the canopy length and the adjustment length ( Lc), in additional LES. Even if the model parameters are, in general, functions of h/ Lc, it was found out that the model is capable of predicting the flow quantities in various cases, when using constant parameters. Subsequently the adjustment region model is combined with the one-dimensional model of Massman, which is applicable for the interior of the canopy, to attain an analytical model capable of describing the mean flow for the full canopy domain. As a result, the model is tested against an analytical model based on a linearization approach.« less

Flow adjustment inside homogeneous canopies after a leading edge – An analytical approach backed by LES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kroniger, Konstantin; Banerjee, Tirtha; De Roo, Frederik

A two-dimensional analytical model for describing the mean flow behavior inside a vegetation canopy after a leading edge in neutral conditions was developed and tested by means of large eddy simulations (LES) employing the LES code PALM. The analytical model is developed for the region directly after the canopy edge, the adjustment region, where one-dimensional canopy models fail due to the sharp change in roughness. The derivation of this adjustment region model is based on an analytic solution of the two-dimensional Reynolds averaged Navier–Stokes equation in neutral conditions for a canopy with constant plant area density (PAD). The main assumptionsmore » for solving the governing equations are separability of the velocity components concerning the spatial variables and the neglection of the Reynolds stress gradients. These two assumptions are verified by means of LES. To determine the emerging model parameters, a simultaneous fitting scheme was applied to the velocity and pressure data of a reference LES simulation. Furthermore a sensitivity analysis of the adjustment region model, equipped with the previously calculated parameters, was performed varying the three relevant length, the canopy height ( h), the canopy length and the adjustment length ( Lc), in additional LES. Even if the model parameters are, in general, functions of h/ Lc, it was found out that the model is capable of predicting the flow quantities in various cases, when using constant parameters. Subsequently the adjustment region model is combined with the one-dimensional model of Massman, which is applicable for the interior of the canopy, to attain an analytical model capable of describing the mean flow for the full canopy domain. As a result, the model is tested against an analytical model based on a linearization approach.« less

Urbanization alters communities of flying arthropods in parks and gardens of a medium-sized city.

PubMed

Lagucki, Edward; Burdine, Justin D; McCluney, Kevin E

2017-01-01

Urbanization transforms undeveloped landscapes into built environments, causing changes in communities and ecological processes. Flying arthropods play important roles in these processes as pollinators, decomposers, and predators, and can be important in structuring food webs. The goal of this study was to identify associations between urbanization and the composition of communities of flying (and floating) arthropods within gardens and parks in a medium-sized mesic city. We predicted that flying arthropod abundance and diversity would respond strongly to percent impervious surface and distance to city center, measurements of urbanization. Flying arthropods were sampled from 30 gardens and parks along an urbanization gradient in Toledo, Ohio, during July and August 2016, using elevated pan traps. A variety of potential predictor variables were also recorded at each site. We collected a total of 2,369 individuals representing nine orders. We found that flying arthropod community composition was associated with percent impervious surface and canopy cover. Overall flying arthropod abundance was negatively associated with percent impervious surface and positively associated with distance to city center. Hymenoptera (bees, wasps, ants), Lepidoptera (moths, butterflies), and Araneae (spiders) were positively associated with distance to city center. Hemiptera (true bugs), Diptera (flies), and Araneae were negatively associated with percent impervious surface. Both distance to city center and percent impervious surface are metrics of urbanization, and this study shows how these factors influence flying arthropod communities in urban gardens and city parks, including significant reductions in taxa that contain pollinators and predators important to urban agriculture and forestry. A variety of environmental factors also showed significant associations with responses (e.g. canopy cover and soil moisture), suggesting these factors may underlie or modulate the urbanization effects. More research is needed to determine mechanisms of change.

Urbanization alters communities of flying arthropods in parks and gardens of a medium-sized city

PubMed Central

Lagucki, Edward

2017-01-01

Urbanization transforms undeveloped landscapes into built environments, causing changes in communities and ecological processes. Flying arthropods play important roles in these processes as pollinators, decomposers, and predators, and can be important in structuring food webs. The goal of this study was to identify associations between urbanization and the composition of communities of flying (and floating) arthropods within gardens and parks in a medium-sized mesic city. We predicted that flying arthropod abundance and diversity would respond strongly to percent impervious surface and distance to city center, measurements of urbanization. Flying arthropods were sampled from 30 gardens and parks along an urbanization gradient in Toledo, Ohio, during July and August 2016, using elevated pan traps. A variety of potential predictor variables were also recorded at each site. We collected a total of 2,369 individuals representing nine orders. We found that flying arthropod community composition was associated with percent impervious surface and canopy cover. Overall flying arthropod abundance was negatively associated with percent impervious surface and positively associated with distance to city center. Hymenoptera (bees, wasps, ants), Lepidoptera (moths, butterflies), and Araneae (spiders) were positively associated with distance to city center. Hemiptera (true bugs), Diptera (flies), and Araneae were negatively associated with percent impervious surface. Both distance to city center and percent impervious surface are metrics of urbanization, and this study shows how these factors influence flying arthropod communities in urban gardens and city parks, including significant reductions in taxa that contain pollinators and predators important to urban agriculture and forestry. A variety of environmental factors also showed significant associations with responses (e.g. canopy cover and soil moisture), suggesting these factors may underlie or modulate the urbanization effects. More research is needed to determine mechanisms of change. PMID:28890848

Urban Tree Species Show the Same Hydraulic Response to Vapor Pressure Deficit across Varying Tree Size and Environmental Conditions

PubMed Central

Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E.

2012-01-01

Background The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. Methodology/Principal Findings We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E c) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G c at VPD = 1 kPa (G cref) and the G c sensitivity to VPD (−dG c/dlnVPD) across studied species as well as under contrasting soil water and R s conditions in the urban area. Conclusions/Significance We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G cref. PMID:23118904

Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

PubMed

Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E

2012-01-01

The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E(c)) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c) at VPD = 1 kPa (G(cref)) and the G(c) sensitivity to VPD (-dG(c)/dlnVPD) across studied species as well as under contrasting soil water and R(s) conditions in the urban area. We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref).

Potential Impacts of Urban Land Expansion on Asian Outflows of Air Pollutants

NASA Astrophysics Data System (ADS)

Wei, T.; Liu, J.; Tao, S.; Ban-Weiss, G. A.

2016-12-01

We investigate the impacts of urban land expansion over Eastern China (EC) on the export of black carbon (BC), carbon monoxide (CO) and ozone (O3) to the West Pacific during the January, April, July and October of 2009, using WRF/Chem model coupled with the tracers tagging technique and an up-to-date single layer urban canopy scheme updated with the treatment of urban hydrological processes. Our model simulations could reproduce well the vertical profiles of Asian outflows of BC and CO observed during the A-FORCE period (March to April of 2009). Over urbanizing areas, increment in urban land fraction could linearly elevate primary pollutants from the lower boundary layer to higher altitudes, and perturb the thermal, hydrological, and kinetic exchange processes between land surface and the atmosphere aloft through all seasons (such local impacts highest in July but lowest in January). Furthermore, we find robust linear relationships exist between urban land fraction (averaged over EC) and export of BC emitted from EC across meridional planes over the western Pacific (e.g., 140 °E). Specifically, each 10% increase in urban land fraction over EC enhances the eastward mass fluxes of BC by about 5%-10% in January and July, and 10%-20% in April and October, respectively, in the free troposphere, which is the dominant pathway for Asian outflows. Such a linear relationship is relatively weaker for CO and only appears in April and October. The different response patterns between BC and CO arise from their distinct physical and chemical properties. Even with decreased vegetation (and reduced biogenic emissions), the O3­ concentrations at the surface and 800 hPa over urbanizing areas both tend to increase. However, no clear trend is observed for the export of O3 over West Pacific for all four months. Urban land expansion facilitates the uplift of local pollutants, but also changes the large-scale circulation pattern (the perturbation cyclone over the downwind Pacific acts to impede the eastward transpacific transport), both playing important roles on the efficiency that Asian emissions are exported. Our finding indicates that the extensive urban land expansion would significantly impact the local climate and air quality, which also have a large impact on long-range transboundary transport.

Modeling of the Urban Heat Island (UHI) using WRF - Assessment of adaptation and mitigation strategies for the city of Stuttgart.

NASA Astrophysics Data System (ADS)

Fallmann, Joachim; Suppan, Peter; Emeis, Stefan

2013-04-01

Cities are warmer than their surroundings (called urban heat island, UHI). UHI influence urban atmospheric circulation, air quality, and ecological conditions. UHI leads to upward motion and compensating near-surface inflow from the surroundings which import rural trace substances. Chemical and aerosol formation processes are modified due to increased temperature, reduced humidity and modified urban-rural trace substance mixtures. UHIs produce enhanced heat stress for humans, animals and plants, less water availability and modified air quality. Growing cities and Climate Change will aggravate the UHI and its effects and urgently require adaptation and mitigation strategies. Prior to this, UHI properties must be assessed by surface observations, ground- and satellite-based vertical remote sensing and numerical modelling. The Weather Research and Forecasting Model (WRF) is an instrument to simulate and assess this phenomenon based on boundary conditions from observations and global climate models. Three urbanization schemes are available with WRF, which are tested during this study for different weather conditions in central Europe and will be enhanced if necessary. High resolution land use maps are used for this modeling effort. In situ measurements and Landsat thermal images are employed for validation of the results. The study will focus on the city of Stuttgart located in the south western part of Germany that is situated in a caldera-like orographic feature. This municipality has a long tradition in urban climate research and thus is well equipped with climatologic measurement stations. By using Geographical Information Systems (GIS), it is possible to simulate several scenarios for different surface properties. By increasing the albedo of roof and wall layers in the urban canopy model or by replacing urban land use by natural vegetation, simple urban planning strategies can be tested and the effect on urban heat island formation and air quality can be investigated. These numerical simulations will then be used to assess effectiveness and impact of planned adaptation and mitigation actions for the UHI under present and future climate conditions. Urban air quality is in the focus of these studies. The study is funded by EU-Project 3CE292P3 - "UHI - Development and application of mitigation and adaptation strategies and measures for counteracting the global UHI phenomenon."

Role of Vegetation and Mulch in Mitigating the Effects of Raindrop Impact on Runoff and Infiltration from Urban Vegetated Green Infrastructure

NASA Astrophysics Data System (ADS)

Alizadehtazi, B.; Montalto, F. A.

2013-12-01

Rain drop impact causes soil crust formation which, in turn, reduces infiltration rates and increases runoff, contributing to soil erosion, downstream flooding and non point source pollutant loads. Unprotected soil surfaces (e.g. without vegetation canopies, mulch, or other materials), are more susceptible to crust formation due to the higher kinetic energy associated with raindrop impact. This impulse breaks larger soil aggregates into smaller particles and disperses soil from its original position. The displaced soil particles self-stratify, with finer particles at the top forming the crust. By contrast, soil that is protected by vegetation canopies and mulch layers is less susceptible to crust formation, since these surfaces intercept raindrops, dissipating some of their kinetic energy prior to their impact with the soil. Very little research has sought to quantify the effect that canopies and mulch can have on this phenomenon. This presentation presents preliminary findings from ongoing study conducted using rainfall simulator to determine the ability of new urban vegetation and mulch to minimize soil crust formation. Three different scenarios are compared: a) bare soil, b) soil with mulch cover, and c) soil protected by vegetation canopies. Soil moisture, surface penetration resistance, and physical measurements of the volume of infiltrate and runoff are made on all three surface treatments after simulated rainfall events. The results are used to discuss green infrastructure facility maintenance and design strategies, namely whether heavily vegetated GI facilities require mulching to maintain infiltration capacity.

Smartphone based hemispherical photography for canopy structure measurement

NASA Astrophysics Data System (ADS)

Wan, Xuefen; Cui, Jian; Jiang, Xueqin; Zhang, Jingwen; Yang, Yi; Zheng, Tao

2018-01-01

The canopy is the most direct and active interface layer of the interaction between plant and environment, and has important influence on energy exchange, biodiversity, ecosystem matter and climate change. The measurement about canopy structure of plant is an important foundation to analyze the pattern, process and operation mechanism of forest ecosystem. Through the study of canopy structure of plant, solar radiation, ambient wind speed, air temperature and humidity, soil evaporation, soil temperature and other forest environmental climate characteristics can be evaluated. Because of its accuracy and effectiveness, canopy structure measurement based on hemispherical photography has been widely studied. However, the traditional method of canopy structure hemispherical photogrammetry based on SLR camera and fisheye lens. This method is expensive and difficult to be used in some low-cost occasions. In recent years, smartphone technology has been developing rapidly. The smartphone not only has excellent image acquisition ability, but also has the considerable computational processing ability. In addition, the gyroscope and positioning function on the smartphone will also help to measure the structure of the canopy. In this paper, we present a smartphone based hemispherical photography system. The system consists of smart phones, low-cost fisheye lenses and PMMA adapters. We designed an Android based App to obtain the canopy hemisphere images through low-cost fisheye lenses and provide horizontal collimation information. In addition, the App will add the acquisition location tag obtained by GPS and auxiliary positioning method in hemisphere image information after the canopy structure hemisphere image acquisition. The system was tested in the urban forest after it was completed. The test results show that the smartphone based hemispherical photography system can effectively collect the high-resolution canopy structure image of the plant.

A canopy radiative transfer scheme with explicit FAPAR for the ISBA-A-gs land surface model: impact on carbon fluxes

NASA Astrophysics Data System (ADS)

Calvet, Jean-Christophe; Carrer, Dominique; Roujean, Jean-Louis; Lafont, Sébastien

2013-04-01

The ISBA-A-gs land surface model is a component of the SURFEX modeling platform developed by Meteo-France, used for research and operational applications in meteorology, hydrology, and climate modeling. ISBA-A-gs simulates hourly water and CO2 fluxes together with soil moisture. An option of the model permits the simulation of the vegetation biomass and of the leaf area index (LAI). The simulated photosynthesis depends on atmospheric CO2 concentration, air temperature and humidity, soil moisture, radiant solar energy, the photosynthetic capacity of the leaves and on factors that condition the distribution of solar radiation over the leaves. In the original version of the model (Jacobs et al. (Agr. Forest Meteorol., 1996), Calvet et al. (Agr. Forest Meteorol., 1998)), the radiative transfer scheme within the canopy was implemented according to a self shading approach. The incident fluxes at the top of the canopy go through a multi-layer vegetation cover. Then, the attenuated flux in the PAR wavelength domain of each layer is used by the photosynthesis model to calculate the leaf net assimilation of CO2 (An). The leaf-level An values are then integrated at the canopy level. In this study, an upgraded version of the radiative transfer model is implemented. An assessment of the vegetation transmittance functions and of various canopy light-response curves is made. The fluxes produced by the new version of ISBA-A-gs are evaluated using data from a number of FLUXNET forest sites. The new model presents systematically better scores than the previous version. Moreover, ISBA-A-gs is now able to simulate prognostic values of the fraction of absorbed PAR (FAPAR). As FAPAR can be observed from space, this new capability permits the validation of the model simulations at a global scale, and the integration of measured FAPAR values in the model through data assimilation techniques.

Doing the hard work where it's easiest? Examining the relationships between urban greening programs and social and ecological characteristics

Treesearch

Dexter H. Locke; J. Morgan Grove

2016-01-01

In this paper we examine the performance of formal programs associated with tree plantings in Washington, D.C. and Baltimore, MD to understand the relationships between the implementation of urban greening programs and the social and ecological characteristics of a city. Previous research has examined variations in patterns of existing and possible tree canopy cover...

Houston’s Urban Forest, 2015

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Christopher B. Edgar; Gretchen Riley; Dudley R. Hartel; Kerry J. Dooley; Sharon M. Stanton; Mark A. Hatfield; Thomas J. Brandeis; Tonya W. Lister

2017-01-01

An analysis of the urban forest in Houston, Texas, reveals that this area has an estimated 33.3 million live trees with tree canopy that covers 18.4 percent of the city. Roughly 19.2 million of the city’s trees are located on private lands. The most common tree species are yaupon, Chinese tallowtree, Chinese privet, Japanese privet, and sugarberry. Trees in Houston...

Comparison of Tillandsia usneoides (Spanish moss) water and leachate dynamics between urban and pristine barrier island maritime oak forests

NASA Astrophysics Data System (ADS)

Van Stan, J. T.; Stubbins, A.; Reichard, J. S.; Wright, K.; Jenkins, R. B.

2013-12-01

Epiphyte coverage on forest canopies can drastically alter the volume and chemical composition of rainwater reaching soils. Along subtropical and tropical coastlines Tillandisa usneoides L. (Spanish moss), in particular, can envelop urban and natural tree crowns. Several cities actively manage their 'moss' covered forest to enhance aesthetics in the most active tourist areas (e.g., Savannah GA, St. Augustine FL, Charleston SC). Since T. usneoides survives through atmospheric water and solute exchange from specialized trichomes (scales), we hypothesized that T. usneoides water storage dynamics and leachate chemistry may be altered by exposure to this active urban atmosphere. 30 samples of T. usneoides from managed forests around the tourist center of Savannah, Georgia, USA were collected to compare with 30 samples from the pristine maritime live oak (Quercus virginiana Mill.) forests of a nearby undeveloped barrier island (St. Catherines Island, Georgia, USA). Maximum water storage capacities were determined via submersion (for all 60 samples) along with dissolved ion (DI) and organic matter (DOM) concentrations (for 15 samples each) after simulated throughfall generation using milliQ ultrapurified water. Further, DOM quality was evaluated (for 15 samples each) using absorbance and fluorescence spectroscopy (EEMS). Results show significant alterations to water storage dynamics, DI, DOM, and DOM quality metrics under urban atmospheric conditions, suggesting modified C and water cycling in urban forest canopies that may, in turn, influence intrasystem nutrient cycles in urban catchment soils or streams via runoff.

Modeling climate change, urbanization, and fire effects on Pinus palustris ecosystems of the southeastern U.S.

USGS Publications Warehouse

Costanza, Jennifer; Terando, Adam J.; McKerrow, Alexa; Collazo, Jaime A.

2015-01-01

Managing ecosystems for resilience and sustainability requires understanding how they will respond to future anthropogenic drivers such as climate change and urbanization. In fire-dependent ecosystems, predicting this response requires a focus on how these drivers will impact fire regimes. Here, we use scenarios of climate change, urbanization and management to simulate the future dynamics of the critically endangered and fire-dependent longleaf pine (Pinus palustris) ecosystem. We investigated how climate change and urbanization will affect the ecosystem, and whether the two conservation goals of a 135% increase in total longleaf area and a doubling of fire-maintained open-canopy habitat can be achieved in the face of these drivers. Our results show that while climatic warming had little effect on the wildfire regime, and thus on longleaf pine dynamics, urban growth led to an 8% reduction in annual wildfire area. The management scenarios we tested increase the ecosystem's total extent by up to 62% and result in expansion of open-canopy longleaf by as much as 216%, meeting one of the two conservation goals for the ecosystem. We find that both conservation goals for this ecosystem, which is climate-resilient but vulnerable to urbanization, are only attainable if a greater focus is placed on restoration of non-longleaf areas as opposed to maintaining existing longleaf stands. Our approach demonstrates the importance of accounting for multiple relevant anthropogenic threats in an ecosystem-specific context in order to facilitate more effective management actions.

Invasive Shrub Mapping in an Urban Environment from Hyperspectral and LiDAR-Derived Attributes.

PubMed

Chance, Curtis M; Coops, Nicholas C; Plowright, Andrew A; Tooke, Thoreau R; Christen, Andreas; Aven, Neal

2016-01-01

Proactive management of invasive species in urban areas is critical to restricting their overall distribution. The objective of this work is to determine whether advanced remote sensing technologies can help to detect invasions effectively and efficiently in complex urban ecosystems such as parks. In Surrey, BC, Canada, Himalayan blackberry ( Rubus armeniacus ) and English ivy ( Hedera helix ) are two invasive shrub species that can negatively affect native ecosystems in cities and managed urban parks. Random forest (RF) models were created to detect these two species using a combination of hyperspectral imagery, and light detection and ranging (LiDAR) data. LiDAR-derived predictor variables included irradiance models, canopy structural characteristics, and orographic variables. RF detection accuracy ranged from 77.8 to 87.8% for Himalayan blackberry and 81.9 to 82.1% for English ivy, with open areas classified more accurately than areas under canopy cover. English ivy was predicted to occur across a greater area than Himalayan blackberry both within parks and across the entire city. Both Himalayan blackberry and English ivy were mostly located in clusters according to a Local Moran's I analysis. The occurrence of both species decreased as the distance from roads increased. This study shows the feasibility of producing highly accurate detection maps of plant invasions in urban environments using a fusion of remotely sensed data, as well as the ability to use these products to guide management decisions.

The model SIRANE for atmospheric urban pollutant dispersion; part I, presentation of the model

NASA Astrophysics Data System (ADS)

Soulhac, Lionel; Salizzoni, Pietro; Cierco, F.-X.; Perkins, Richard

2011-12-01

In order to control and manage urban air quality, public authorities require an integrated approach that incorporates direct measurements and modelling of mean pollutant concentrations. These have to be performed by means of operational modelling tools, that simulate the transport of pollutants within and above the urban canopy over a large number of streets. The operational models must be able to assess rapidly a large variety of situations and with limited computing resources. SIRANE is an operational urban dispersion model based on a simplified description of the urban geometry that adopts parametric relations for the pollutant transfer phenomena within and out of the urban canopy. The streets in a city district are modelled as a network of connected street segments. The flow within each street is driven by the component of the external wind parallel to the street, and the pollutant is assumed to be uniformly mixed within the street. The model contains three main mechanisms for transport in and out of a street: advection along the street axis, diffusion across the interface between the street and the overlying air flow and exchanges with other streets at street intersections. The dispersion of pollutants advected or diffused out of the streets is taken into account using a Gaussian plume model, with the standard deviations σ y and σ z parameterised by the similarity theory. The input data for the final model are the urban geometry, the meteorological parameters, the background concentration of pollutants advected into the model domain by the wind and the emissions within each street in the network.

Validation of Martilli's urban boundary layer scheme with measurements from two mid-latitude European cities

NASA Astrophysics Data System (ADS)

Hamdi, R.; Schayes, G.

2007-08-01

Martilli's urban parameterization scheme is improved and implemented in a mesoscale model in order to take into account the typical effects of a real city on the air temperature near the ground and on the surface exchange fluxes. The mesoscale model is run on a single column using atmospheric data and radiation recorded above roof level as forcing. Here, the authors validate Martilli's urban boundary layer scheme using measurements from two mid-latitude European cities: Basel, Switzerland and Marseilles, France. For Basel, the model performance is evaluated with observations of canyon temperature, surface radiation, and energy balance fluxes obtained during the Basel urban boundary layer experiment (BUBBLE). The results show that the urban parameterization scheme represents correctly most of the behavior of the fluxes typical of the city center of Basel, including the large heat uptake by the urban fabric and the positive sensible heat flux at night. For Marseilles, the model performance is evaluated with observations of surface temperature, canyon temperature, surface radiation, and energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) and its urban boundary layer (UBL) campaign. At both urban sites, vegetation cover is less than 20%, therefore, particular attention was directed to the ability of Martilli's urban boundary layer scheme to reproduce the observations for the Marseilles city center, where the urban parameters and the synoptic forcing are totally different from Basel. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model correctly simulates the net radiation, canyon temperature, and the partitioning between the turbulent and storage heat fluxes.

Estimating Carbon Storage and Sequestration by Urban Trees at Multiple Spatial Resolutions

NASA Astrophysics Data System (ADS)

Wu, J.; Tran, A.; Liao, A.

2010-12-01

Urban forests are an important component of urban-suburban environments. Urban trees provide not only a full range of social and psychological benefits to city dwellers, but also valuable ecosystem services to communities, such as removing atmospheric carbon dioxide, improving air quality, and reducing storm water runoff. There is an urgent need for developing strategic conservation plans for environmentally sustainable urban-suburban development based on the scientific understanding of the extent and function of urban forests. However, several challenges remain to accurately quantify various environmental benefits provided by urban trees, among which is to deal with the effect of changing spatial resolution and/or scale. In this study, we intended to examine the uncertainties of carbon storage and sequestration associated with the tree canopy coverage of different spatial resolutions. Multi-source satellite imagery data were acquired for the City of Fullerton, located in Orange County of California. The tree canopy coverage of the study area was classified at three spatial resolutions, ranging from 30 m (Landsat-5 Thematic Mapper), 15 m (Advanced Spaceborne Thermal Emission and Reflection Radiometer), to 2.5 m (QuickBird). We calculated the amount of carbon stored in the trees represented on the individual tree coverage maps and the annual carbon taken up by the trees with a model (i.e., CITYgreen) developed by the U.S. Forest Service. The results indicate that urban trees account for significant proportions of land cover in the study area even with the low spatial resolution data. The estimated carbon fixation benefits vary greatly depending on the details of land use and land cover classification. The extrapolation of estimation from the fine-resolution stand-level to the low-resolution landscape-scale will likely not preserve reasonable accuracy.

The Detection and Characterization of Urbanization, Industrialization, and Longwall Mining Impacts on Forest Ecosystems Through the Use of GiS and Remote Sensing Techniques

NASA Astrophysics Data System (ADS)

Pfeil-McCullough, Erin Kathleen

Urbanization has far reaching and significant effects on forest ecosystems, directly through urban development and indirectly through supportive processes such as coal mining and agriculture. Urban processes modify the landscape leading to altered hillslope hydrology, increased disturbance, and the introduction of non-native forest pathogens. This dissertation addresses several challenges in our ability to detect these urbanization impacts on forests via geospatial analyses. The role of forests in urban hydrological processes has been extensively studied, but the impacts of urbanized hydrology on forests remain poorly examined. This dissertation documented impacts to hydrology and forests at variety of temporal and spatial scales: 1) A geospatial comparison of the historic and contemporary forests of Allegheny County, Pennsylvania revealed substantial shifts in tree species, but less change in the species soil moisture preference. These results document additional evidence that increased heterogeneity in urban soil moisture alters forest structure. 2) To examine soil moisture changes, impacts of longwall mine subsidence were assessed by using a Landsat based canopy moisture index and hot spot analysis tools at the forest patch scale. Declines in forest canopy moisture were detected over longwall mines as mining progressed through time, and results contradicted assumptions that the hydrological impacts overlying LMS recover within 4-5 years following subsidence of undermined land. 3) Utilizing a landslide susceptibility model (SINMAP), increases in landslide susceptibility were predicted in Pittsburgh, PA based on several scenarios of ash tree loss to the emerald ash borer (EAB), a bark beetle that rapidly kills ash trees. This model provides a tool to predict changes in landslide susceptibility following tree loss, increasing the understanding of urban forest function and its role in slope stability. Detecting how urbanized hydrology impacts forest health, function, and development is fundamental to sustaining the services forests provide. Results from this dissertation will ultimately allow improvements in the management and protection of both trees and water resources in urban systems and beyond.

Multiple health benefits of urban tree canopy: The mounting evidence for a green prescription

Treesearch

Jared M. Ulmer; Kathleen L. Wolf; Desiree R. Backman; Raymond L. Tretheway; Cynthia JA Blain; Jarlath PM O’Neil-Dunne; Lawrence D. Frank

2016-01-01

The purpose of this study was to enhance the understanding of the health-promoting potential of trees in an urbanized region of the United States. This was done using high-resolution LiDAR and imagery data to quantify tree cover within 250 m of the residence of 7910 adult participants in the California Health Interview Survey, then testing for main and mediating...

Assessing urban forest effects and values, Los Angeles' urban forest

Treesearch

David J. Nowak; Robert E. III Hoehn; Daniel E. Crane; Lorraine Weller; Antonio Davila

2011-01-01

An analysis of trees in Los Angeles, CA, reveals that this area has about 6 million trees with tree and shrub canopies that cover 24.9 percent of the city. The most common tree species are Italian cypress, scrub oak, laurel sumac, Mexican fan palm, and Indian laurel, Trees in Los Angeles currently store about 1.3 million tons of carbon (4.7 million tons CO2...

Strategic tree planting as an EPA encouraged pollutant reduction strategy: how urban trees can obtain credit in state implementation plans

Treesearch

Dr. David J. Nowak

2005-01-01

As tree programs are new to the SIP process, "to facilitate Federal approval of an emerging or voluntary measure States are encouraged to work with their EPA regional ofice during the development process". Programs to increase canopy cover in urban areas can achieve many benefits. They can help improve air and water quality, as well as other factors related...

A two stream radiative transfer model for scaling solar induced fluorescence from leaf to canopy

NASA Astrophysics Data System (ADS)

Quaife, T. L.

2017-12-01

Solar induced fluorescence (SIF) is becoming widely used as a proxy for gross primary productivity (GPP), in particular with the advent of its measurement by Earth Observation satellites such as OCO and GOSAT. A major attraction of SIF is that it is independent of the assumptions embedded in light use efficiency based GPP products derived from satellite missions such as MODIS. The assumptions in such products are likely not compatible with any given land surface model and hence comparing the two is problematic. On the other hand to compare land surface model predictions of GPP to satellite based SIF data requires either (a) translation of SIF into estimates of GPP, or (b) direct predictions of SIF from the land surface model itself. The former typically relies on empirical relationships, whereas the latter can make direct use of our physiological understanding of the link between photosynthesis and fluorescence at the leaf scale and is therefore preferable. Here I derive a two stream model for fluorescence that is capable of translating between leaf scale models of SIF and the canopy leaving radiance taking into account all levels of photon scattering. Other such models have been developed previously but the model described here is physically consistent with the Sellers' two stream radiative transfer scheme which is widely used in modern land surface models. Consequently any model that already employs the Sellers's scheme can use the new model without requiring modification. This includes, for example, JULES, the land surface model of the new UK Earth System Model (UKESM) and CLM, the US Community Land Model (part of the NCAR Earth System Model). The new canopy SIF model is extremely computationally efficient and can be applied to vertically inhomogeneous canopies.

Water Vapor Exchange in a Costa Rican Lower Montane Tropical Forest

NASA Astrophysics Data System (ADS)

Andrews, R.; Miller, G. R.; Cahill, A. T.; Moore, G. W.; Aparecido, L. M. T.

2015-12-01

Because of high canopy interception in tropical forests, evaporation from wet canopy surfaces makes up a sizeable portion of the total water vapor flux. The modeling complexities presented by changing canopy wetness, along with a scarcity of land-atmosphere flux exchange data from tropical forests, means evapotranspiration (ET) processes have been poorly represented in the tropics in land-surface modeling schemes. To better understand tropical forest ET, we will evaluate the influence of canopy wetness and various micrometeorological data on ET partitioning and total ET flux. We have collected flux data from a lower montane forest in Costa Rica at a newly established AmeriFlux site, which notably has the highest mean annual precipitation of any site in the network. The site features a 39-m canopy tower, equipped with two eddy covariance systems (LI-7200, LI-COR), a CO2/H2O atmospheric profile system (AP200, Campbell Scientific), leaf wetness sensors (LWS, Decagon Devices), sap flow sensors, and a soil respiration chamber (LI-8100A, LI-COR) as well as an array of other micrometeorological sensors. At the site, total ET is driven primarily by available energy, and to a lesser extent, by vapor pressure deficit. Average daily latent energy fluxes peak at values of 160, 75, and 35 W m-2 for dry, partially wet, and wet canopy conditions respectively. Correlations between latent energy flux and all other variables are strongest for drier canopy conditions. Complex relationships between canopy wetness and tropical forest ET cause the environmental controls on these fluxes to be significantly different from those in other biomes. As a result, a new modeling paradigm is needed to more accurately model ET differences between tropical forests and other vegetation types.

Contributions to urban heat island on the local neighborhood scale

NASA Astrophysics Data System (ADS)

Hertel, Daniel; Schlink, Uwe

2017-04-01

Already today around half of the global population is living in urban regions and recent studies expect a further increase until mid-21st century. Therefore, especially in the context of climate change, an increasing amount of urban inhabitants are affected by urban climate and air quality. One special characteristic of urban climate is the urban heat island (UHI) effect, where urbanized regions are warmer than the rural surroundings. With respect to climate change and the growing urbanization it is obvious that the UHI effect will tend to be intensified. To keep our cities worth living, it is necessary to think about adaptation and mitigation strategies which refer to both, climate protection as well as utilization of chances resulting from climate changes. One step to a more precisely adaptation, particularly on the neighborhood scale, is an improved understanding of the magnitude of bio geophysical processes (e.g.: radiation balance, convection efficiency, evapotranspiration, storage heat, anthropogenic heat etc.), which contribute to the urban warming. Considering that UHI can be expressed as temperature difference ΔT between urban and rural areas, we can interpret these processes as how they would change temperature, because of energy redistribution, from a rural area to an urbanized region. Up to now on the local scale there is a knowledge gap about these processes. The mentioned processes are parts of a surface energy balance (based on the work of Zhao et al., 2014). That means they refer to the surface UHI effect and not to the canopy layer UHI effect. Assuming that the urban region is a volume with the top at the height of the canopy layer, we can approximately identify the surface UHI effect as the canopy layer UHI effect since the information comes from both the surface and the atmosphere inside. This assumption is not valid for Zhao's approach because they analyzed whole cities and could neglect such processes within the volume. This contribution presents first results from my PhD project where I take micrometeorological simulations for a case study site ("Bayerischer Bahnhof" in Leipzig; Saxony, Germany; 51°20', 12°22') from the ENVI-met model and calculate the UHI as well as the contributing bio geophysical processes. The results are maps of the processes that directly quantify their contribution to the total UHI at each point in the area. The benefits of this approach can be seen in the small resolution (3x3 m) of the simulation area which gives further insights into local UHI variances. Also, the effects of restructuring within quarters and methods to avoid adverse health impacts on the residents can be developed in a more precisely and sophisticated way. Zhao, L., Lee, X., Smith, R.B., Oleson, K., (2014): Strong contributions of local background climate to urban heat islands. Nature 511: 216-219, doi: 10.1038/nature13462

Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China, during the 2014 APEC summit

NASA Astrophysics Data System (ADS)

Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

2015-11-01

The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the Beijing 325 m meteorological tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition near ground level using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3- / SO42- mass ratios illustrates an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed of secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors. In addition to emission controls, the routine circulations of mountain-valley breezes were also found to play an important role in alleviating PM levels and achieving the "APEC blue" effect. The evolution of vertical differences between 260 m and the ground level was also investigated. Our results show complex vertical differences during the formation and evolution of severe haze episodes that are closely related to aerosol sources and boundary-layer dynamics.

Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China during 2014 APEC summit

NASA Astrophysics Data System (ADS)

Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

2015-08-01

The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the 325 m Beijing Meteorological Tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition at near ground level using a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3-/SO42- mass ratios illustrate an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed by secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors such as SO2, NOx, and volatile organic compounds (VOCs). In addition to emission controls, the routine circulations of mountain-valley breezes were also found to play an important role in alleviating PM levels and achieving the "APEC blue" effect. The evolution of vertical differences between 260 m and the ground level was also investigated. Our results show complex vertical differences during the formation and evolution of severe haze episodes that are closely related to aerosol sources and boundary layer dynamics.

Adjustment of Turbulent Boundary-Layer Flow to Idealized Urban Surfaces: A Large-Eddy Simulation Study

NASA Astrophysics Data System (ADS)

Cheng, Wai-Chi; Porté-Agel, Fernando

2015-05-01

Large-eddy simulations (LES) are performed to simulate the atmospheric boundary-layer (ABL) flow through idealized urban canopies represented by uniform arrays of cubes in order to better understand atmospheric flow over rural-to-urban surface transitions. The LES framework is first validated with wind-tunnel experimental data. Good agreement between the simulation results and the experimental data are found for the vertical and spanwise profiles of the mean velocities and velocity standard deviations at different streamwise locations. Next, the model is used to simulate ABL flows over surface transitions from a flat homogeneous terrain to aligned and staggered arrays of cubes with height . For both configurations, five different frontal area densities , equal to 0.028, 0.063, 0.111, 0.174 and 0.250, are considered. Within the arrays, the flow is found to adjust quickly and shows similar structure to the wake of the cubes after the second row of cubes. An internal boundary layer is identified above the cube arrays and found to have a similar depth in all different cases. At a downstream location where the flow immediately above the cube array is already adjusted to the surface, the spatially-averaged velocity is found to have a logarithmic profile in the vertical. The values of the displacement height are found to be quite insensitive to the canopy layout (aligned vs. staggered) and increase roughly from to as increases from 0.028 to 0.25. Relatively larger values of the aerodynamic roughness length are obtained for the staggered arrays, compared with the aligned cases, and a maximum value of is found at for both configurations. By explicitly calculating the drag exerted by the cubes on the flow and the drag coefficients of the cubes using our LES results, and comparing the results with existing theoretical expressions, we show that the larger values of for the staggered arrays are related to the relatively larger drag coefficients of the cubes for that configuration compared with the aligned one. The effective mixing length within and above different cube arrays is also calculated and a local maximum of within the canopy is found in all the cases, with values ranging from to . These patterns of are different from those used in existing urban canopy models.

Air quality and human health impacts of grasslands and shrublands in the United States

NASA Astrophysics Data System (ADS)

Gopalakrishnan, Varsha; Hirabayashi, Satoshi; Ziv, Guy; Bakshi, Bhavik R.

2018-06-01

Vegetation including canopy, grasslands, and shrublands can directly sequester pollutants onto the plant surface, resulting in an improvement in air quality. Until now, several studies have estimated the pollution removal capacity of canopy cover at the level of a county, but no such work exists for grasslands and shrublands. This work quantifies the air pollution removal capacity of grasslands and shrublands at the county-level in the United States and estimates the human health benefits associated with pollution removal using the i-Tree Eco model. Sequestration of pollutants is estimated based on the Leaf Area Index (LAI) obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS) derived dataset estimates of LAI and the percentage land cover obtained from the National Land Cover Database (NLCD) for the year 2010. Calculation of pollution removal capacity using local environmental data indicates that grasslands and shrublands remove a total of 6.42 million tonnes of air pollutants in the United States and the associated monetary benefits total 268 million. Human health impacts and associated monetary value due to pollution removal was observed to be significantly high in urban areas indicating that grasslands and shrublands are equally critical as canopy in improving air quality and human health in urban regions.

Evaluating the performance of land surface model ORCHIDEE-CAN v1.0 on water and energy flux estimation with a single- and multi-layer energy budget scheme

NASA Astrophysics Data System (ADS)

Chen, Yiying; Ryder, James; Bastrikov, Vladislav; McGrath, Matthew J.; Naudts, Kim; Otto, Juliane; Ottlé, Catherine; Peylin, Philippe; Polcher, Jan; Valade, Aude; Black, Andrew; Elbers, Jan A.; Moors, Eddy; Foken, Thomas; van Gorsel, Eva; Haverd, Vanessa; Heinesch, Bernard; Tiedemann, Frank; Knohl, Alexander; Launiainen, Samuli; Loustau, Denis; Ogée, Jérôme; Vessala, Timo; Luyssaert, Sebastiaan

2016-09-01

Canopy structure is one of the most important vegetation characteristics for land-atmosphere interactions, as it determines the energy and scalar exchanges between the land surface and the overlying air mass. In this study we evaluated the performance of a newly developed multi-layer energy budget in the ORCHIDEE-CAN v1.0 land surface model (Organising Carbon and Hydrology In Dynamic Ecosystems - CANopy), which simulates canopy structure and can be coupled to an atmospheric model using an implicit coupling procedure. We aim to provide a set of acceptable parameter values for a range of forest types. Top-canopy and sub-canopy flux observations from eight sites were collected in order to conduct this evaluation. The sites crossed climate zones from temperate to boreal and the vegetation types included deciduous, evergreen broad-leaved and evergreen needle-leaved forest with a maximum leaf area index (LAI; all-sided) ranging from 3.5 to 7.0. The parametrization approach proposed in this study was based on three selected physical processes - namely the diffusion, advection, and turbulent mixing within the canopy. Short-term sub-canopy observations and long-term surface fluxes were used to calibrate the parameters in the sub-canopy radiation, turbulence, and resistance modules with an automatic tuning process. The multi-layer model was found to capture the dynamics of sub-canopy turbulence, temperature, and energy fluxes. The performance of the new multi-layer model was further compared against the existing single-layer model. Although the multi-layer model simulation results showed few or no improvements to both the nighttime energy balance and energy partitioning during winter compared with a single-layer model simulation, the increased model complexity does provide a more detailed description of the canopy micrometeorology of various forest types. The multi-layer model links to potential future environmental and ecological studies such as the assessment of in-canopy species vulnerability to climate change, the climate effects of disturbance intensities and frequencies, and the consequences of biogenic volatile organic compound (BVOC) emissions from the terrestrial ecosystem.

Assessing urban vacant land ecosystem services: Urban vacant land as green infrastructure in the City of Roanoke, Virginia

Treesearch

Gunwoo Kim; Patrick A. Miller; David J. Nowak

2015-01-01

The research reported here quantifies the ecosystem services and values of vacant land using the City of Roanoke, Virginia as a study site. Aerial photo interpretation with ground-truthing was used to identify and catalog vacant parcels of land within the city limits and the results mapped using the i-Tree Canopy and i-Tree Eco models to define land cover classes and...

Mapping evapotranspiration with high resolution aircraft imagery over vineyards using one and two source modeling schemes

USDA-ARS?s Scientific Manuscript database

Thermal and multispectral remote sensing data from low-altitude aircraft can provide high spatial resolution necessary for sub-field (= 10 m) and plant canopy (= 1 m) scale evapotranspiration (ET) monitoring. In this study, high resolution aircraft sub-meter scale thermal infrared and multispectral...

Invasive Shrub Mapping in an Urban Environment from Hyperspectral and LiDAR-Derived Attributes

PubMed Central

Chance, Curtis M.; Coops, Nicholas C.; Plowright, Andrew A.; Tooke, Thoreau R.; Christen, Andreas; Aven, Neal

2016-01-01

Proactive management of invasive species in urban areas is critical to restricting their overall distribution. The objective of this work is to determine whether advanced remote sensing technologies can help to detect invasions effectively and efficiently in complex urban ecosystems such as parks. In Surrey, BC, Canada, Himalayan blackberry (Rubus armeniacus) and English ivy (Hedera helix) are two invasive shrub species that can negatively affect native ecosystems in cities and managed urban parks. Random forest (RF) models were created to detect these two species using a combination of hyperspectral imagery, and light detection and ranging (LiDAR) data. LiDAR-derived predictor variables included irradiance models, canopy structural characteristics, and orographic variables. RF detection accuracy ranged from 77.8 to 87.8% for Himalayan blackberry and 81.9 to 82.1% for English ivy, with open areas classified more accurately than areas under canopy cover. English ivy was predicted to occur across a greater area than Himalayan blackberry both within parks and across the entire city. Both Himalayan blackberry and English ivy were mostly located in clusters according to a Local Moran’s I analysis. The occurrence of both species decreased as the distance from roads increased. This study shows the feasibility of producing highly accurate detection maps of plant invasions in urban environments using a fusion of remotely sensed data, as well as the ability to use these products to guide management decisions. PMID:27818664

Efficiently modelling urban heat storage: an interface conduction scheme in an urban land surface model (aTEB v2.0)

NASA Astrophysics Data System (ADS)

Lipson, Mathew J.; Hart, Melissa A.; Thatcher, Marcus

2017-03-01

Intercomparison studies of models simulating the partitioning of energy over urban land surfaces have shown that the heat storage term is often poorly represented. In this study, two implicit discrete schemes representing heat conduction through urban materials are compared. We show that a well-established method of representing conduction systematically underestimates the magnitude of heat storage compared with exact solutions of one-dimensional heat transfer. We propose an alternative method of similar complexity that is better able to match exact solutions at typically employed resolutions. The proposed interface conduction scheme is implemented in an urban land surface model and its impact assessed over a 15-month observation period for a site in Melbourne, Australia, resulting in improved overall model performance for a variety of common material parameter choices and aerodynamic heat transfer parameterisations. The proposed scheme has the potential to benefit land surface models where computational constraints require a high level of discretisation in time and space, for example at neighbourhood/city scales, and where realistic material properties are preferred, for example in studies investigating impacts of urban planning changes.

Environmental and biological controls of urban tree transpiration in the Upper Midwest

NASA Astrophysics Data System (ADS)

Peters, E. B.; McFadden, J.; Montgomery, R.

2009-12-01

Urban trees provide a variety of ecosystem services to urban and suburban areas, including carbon uptake, climate amelioration, energy reduction, and stormwater management. Tree transpiration, in particular, modifies urban water budgets by providing an alternative pathway for water after rain events. The relative importance of environmental and biological controls on transpiration are poorly understood in urban areas, yet these controls are important for quantifying and scaling up the ecosystem services that urban trees provide at landscape and regional scales and predicting how urban ecosystems will respond to climate changes. The objectives of our study were to quantify the annual cycle of tree transpiration in an urban ecosystem and to determine how different urban tree species and plant functional types respond to environmental drivers. We continuously measured whole-tree transpiration using thermal dissipation sap flow at four urban forest stands that were broadly representative of the species composition and tree sizes found in a suburban residential neighborhood of Minneapolis-Saint Paul, Minnesota. A total of 40 trees, representing different species, plant functional types, successional stages, and xylem anatomy, were sampled throughout the 2007 and 2008 growing seasons (April-November). At each site we monitored soil moisture, air temperature, and relative humidity continuously, and we measured leaf area index weekly. Urban tree transpiration was strongly correlated with diurnal changes in vapor pressure deficit and photosynthetically active radiation and with seasonal changes in leaf area index. We found that plant functional type better explained species differences in transpiration per canopy area than either successional stage or xylem anatomy, largely due to differences in canopy structure between conifer and broad-leaf deciduous trees. We also observed inter-annual differences in transpiration rates due to a mid-season drought and longer growing season in 2007, compared with the cooler, wetter conditions in 2008. These results were scaled to estimate the relative contribution of each tree type at the scale of a suburban landscape. The findings of this study have implications for understanding the role of trees in managing urban water budgets and predicting the impacts of climate change on urban ecosystem services.

Regional climate model assessment of the urban land-surface forcing over central Europe

NASA Astrophysics Data System (ADS)

Huszar, P.; Halenka, T.; Belda, M.; Zak, M.; Sindelarova, K.; Miksovsky, J.

2014-07-01

For the purpose of qualifying and quantifying the climate impact of cities and urban surfaces in general on climate of central Europe, the surface parameterization in regional climate model RegCM4 has been extended with the Single Layer Urban Canopy Model (SLUCM). A set of experiments was performed over the period of 2005-2009 for central Europe, either without considering urban surfaces or with the SLUCM treatment. Results show a statistically significant impact of urbanized surfaces on temperature (up to 1.5 K increase in summer) as well as on the boundary layer height (increases up to 50 m). Urbanization further influences surface wind with a winter decrease up to -0.6 m s-1, though both increases and decreases were detected in summer depending on the location relative to the cities and daytime (changes up to 0.3 m s-1). Urban surfaces significantly reduce evaporation and thus the humidity over the surface. This impacts the simulated summer precipitation rate, showing decrease over cities up to -2 mm day-1. Significant temperature increases are simulated over higher elevations as well, not only within the urban canopy layer. With the urban parameterization, the climate model better describes the diurnal temperature variation, reducing the cold afternoon and evening bias of RegCM4. Sensitivity experiments were carried out to quantify the response of the meteorological conditions to changes in the parameters specific to the urban environment such as street width, building height, albedo of the roofs and anthropogenic heat release. The results proved to be rather robust and the choice of the key SLUCM parameters impacts them only slightly (mainly temperature, boundary layer height and wind velocity). Statistically significant impacts are modeled not only over large urbanized areas, but the influence of the cities is also evident over rural areas without major urban surfaces. It is shown that this is the result of the combined effect of the distant influence of the cities and the influence of the minor local urban surface coverage.

Regional climate model assessment of the urban land-surface forcing over central Europe

NASA Astrophysics Data System (ADS)

Huszar, P.; Halenka, T.; Belda, M.; Zak, M.; Sindelarova, K.; Miksovsky, J.

2014-11-01

For the purpose of qualifying and quantifying the climate impact of cities and urban surfaces in general on climate of central Europe, the surface parameterization in regional climate model RegCM4 has been extended with the Single-layer Urban Canopy Model (SLUCM). A set of experiments was performed over the period of 2005-2009 for central Europe, either without considering urban surfaces or with the SLUCM treatment. Results show a statistically significant impact of urbanized surfaces on temperature (up to 1.5 K increase in summer) as well as on the boundary layer height (increases up to 50 m). Urbanization further influences surface wind with a winter decrease up to -0.6 m s-1, though both increases and decreases were detected in summer depending on the location relative to the cities and daytime (changes up to 0.3 m s-1). Urban surfaces significantly reduce the humidity over the surface. This impacts the simulated summer precipitation rate, showing a decrease over cities of up to -2 mm day-1. Significant temperature increases are simulated over higher altitudes as well, not only within the urban canopy layer. With the urban parameterization, the climate model better describes the diurnal temperature variation, reducing the cold afternoon and evening bias of RegCM4. Sensitivity experiments were carried out to quantify the response of the meteorological conditions to changes in the parameters specific to the urban environment, such as street width, building height, albedo of the roofs and anthropogenic heat release. The results proved to be rather robust and the choice of the key SLUCM parameters impacts them only slightly (mainly temperature, boundary layer height and wind velocity). Statistically significant impacts are modelled not only over large urbanized areas, but the influence of the cities is also evident over rural areas without major urban surfaces. It is shown that this is the result of the combined effect of the distant influence of the cities and the influence of the minor local urban surface coverage.

Parameter Estimation and Sensitivity Analysis of an Urban Surface Energy Balance Parameterization at a Tropical Suburban Site

NASA Astrophysics Data System (ADS)

Harshan, S.; Roth, M.; Velasco, E.

2014-12-01

Forecasting of the urban weather and climate is of great importance as our cities become more populated and considering the combined effects of global warming and local land use changes which make urban inhabitants more vulnerable to e.g. heat waves and flash floods. In meso/global scale models, urban parameterization schemes are used to represent the urban effects. However, these schemes require a large set of input parameters related to urban morphological and thermal properties. Obtaining all these parameters through direct measurements are usually not feasible. A number of studies have reported on parameter estimation and sensitivity analysis to adjust and determine the most influential parameters for land surface schemes in non-urban areas. Similar work for urban areas is scarce, in particular studies on urban parameterization schemes in tropical cities have so far not been reported. In order to address above issues, the town energy balance (TEB) urban parameterization scheme (part of the SURFEX land surface modeling system) was subjected to a sensitivity and optimization/parameter estimation experiment at a suburban site in, tropical Singapore. The sensitivity analysis was carried out as a screening test to identify the most sensitive or influential parameters. Thereafter, an optimization/parameter estimation experiment was performed to calibrate the input parameter. The sensitivity experiment was based on the "improved Sobol's global variance decomposition method" . The analysis showed that parameters related to road, roof and soil moisture have significant influence on the performance of the model. The optimization/parameter estimation experiment was performed using the AMALGM (a multi-algorithm genetically adaptive multi-objective method) evolutionary algorithm. The experiment showed a remarkable improvement compared to the simulations using the default parameter set. The calibrated parameters from this optimization experiment can be used for further model validation studies to identify inherent deficiencies in model physics.

Urban forest ecosystem analysis using fused airborne hyperspectral and lidar data

NASA Astrophysics Data System (ADS)

Alonzo, Mike Gerard

Urban trees are strategically important in a city's effort to mitigate their carbon footprint, heat island effects, air pollution, and stormwater runoff. Currently, the most common method for quantifying urban forest structure and ecosystem function is through field plot sampling. However, taking intensive structural measurements on private properties throughout a city is difficult, and the outputs from sample inventories are not spatially explicit. The overarching goal of this dissertation is to develop methods for mapping urban forest structure and function using fused hyperspectral imagery and waveform lidar data at the individual tree crown scale. Urban forest ecosystem services estimated using the USDA Forest Service's i-Tree Eco (formerly UFORE) model are based largely on tree species and leaf area index (LAI). Accordingly, tree species were mapped in my Santa Barbara, California study area for 29 species comprising >80% of canopy. Crown-scale discriminant analysis methods were introduced for fusing Airborne Visible Infrared Imaging Spectrometry (AVIRIS) data with a suite of lidar structural metrics (e.g., tree height, crown porosity) to maximize classification accuracy in a complex environment. AVIRIS imagery was critical to achieving an overall species-level accuracy of 83.4% while lidar data was most useful for improving the discrimination of small and morphologically unique species. LAI was estimated at both the field-plot scale using laser penetration metrics and at the crown scale using allometry. Agreement of the former with photographic estimates of gap fraction and the latter with allometric estimates based on field measurements was examined. Results indicate that lidar may be used reasonably to measure LAI in an urban environment lacking in continuous canopy and characterized by high species diversity. Finally, urban ecosystem services such as carbon storage and building energy-use modification were analyzed through combination of aforementioned methods and the i-Tree Eco modeling framework. The remote sensing methods developed in this dissertation will allow researchers to more precisely constrain urban ecosystem spatial analyses and equip cities to better manage their urban forest resource.

Streams in the urban heat island: spatial and temporal variability in temperature

USGS Publications Warehouse

Somers, Kayleigh A.; Bernhardt, Emily S.; Grace, James B.; Hassett, Brooke A.; Sudduth, Elizabeth B.; Wang, Siyi; Urban, Dean L.

2013-01-01

Streams draining urban heat islands tend to be hotter than rural and forested streams at baseflow because of warmer urban air and ground temperatures, paved surfaces, and decreased riparian canopy. Urban infrastructure efficiently routes runoff over hot impervious surfaces and through storm drains directly into streams and can lead to rapid, dramatic increases in temperature. Thermal regimes affect habitat quality and biogeochemical processes, and changes can be lethal if temperatures exceed upper tolerance limits of aquatic fauna. In summer 2009, we collected continuous (10-min interval) temperature data in 60 streams spanning a range of development intensity in the Piedmont of North Carolina, USA. The 5 most urbanized streams averaged 21.1°C at baseflow, compared to 19.5°C in the 5 most forested streams. Temperatures in urban streams rose as much as 4°C during a small regional storm, whereas the same storm led to extremely small to no changes in temperature in forested streams. Over a kilometer of stream length, baseflow temperature varied by as much as 10°C in an urban stream and as little as 2°C in a forested stream. We used structural equation modeling to explore how reach- and catchment-scale attributes interact to explain maximum temperatures and magnitudes of storm-flow temperature surges. The best predictive model of baseflow temperatures (R2  =  0.461) included moderately strong pathways directly (extent of development and road density) and indirectly, as mediated by reach-scale factors (canopy closure and stream width), from catchment-scale factors. The strongest influence on storm-flow temperature surges appeared to be % development in the catchment. Reach-scale factors, such as the extent of riparian forest and stream width, had little mitigating influence (R2  =  0.448). Stream temperature is an essential, but overlooked, aspect of the urban stream syndrome and is affected by reach-scale habitat variables, catchment-scale urbanization, and stream thermal regimes.

Flux measurements of energy and trace gases in urban Houston, Texas

NASA Astrophysics Data System (ADS)

Boedeker, I.; Schade, G. W.; Adams, S.; Park, C.

2008-12-01

We describe the setup and some first year results of a new flux measurements tower in an urban area. An existing radio communications tower 4 km north of downtown Houston was equipped with micrometeorological instrumentation and trace gas sampling lines in spring 2007. Wind speed, temperature and relative humidity are recorded at five levels between 12 and 60 m above ground; 3-D wind speed measurements, solar and net radiances, and trace gas sampling are established from the 60 m level. A closed path IRGA is used for CO2 and water vapor fluxes, and independent instrumentation for criteria pollutant and VOC fluxes. Two CSI data loggers and software control the measurements, and EdiRe software is used to analyze turbulence data and compute fluxes. A project description is provided at http://atmo.tamu.edu/yellowcabtower. Surface properties as calculated from the gradient measurements show the site to be surprisingly uniform, with displacement heights between 5 and 9 m and roughness lengths between 0.4 and 0.7 m, despite urban heterogeneity. The latter is investigated through visible/near IR orthoimagery and LIDAR data, which are incorporated into a local GIS. Net radiation was also only marginally affected by surface heterogeneity. At this urban location it is balanced by roughly equal amounts of sensible heat, latent heat, and storage fluxes. Latent heat flux, however, is smaller outside the growing season, with an equivalent increase in winter storage fluxes, as expected. Significant differences are also observed with direction during summer, showing decreased Bowen ratios and lower CO2 emissions from sectors with a larger urban tree canopy cover in the footprint. The largely mature, dominantly oak urban canopy cover alleviates approximately 100 W m- 2 during typical summer days. On the other hand, anthropogenic CO2 emissions dominate over photosynthetic uptake all year round. Measured carbon fluxes peak during morning rush-hour traffic, especially when increasing stretches of the main commuter road fall into the footprint. Outside the rush hour, daytime carbon fluxes typically ranged from 0.4 to 1.6 g C m-2 h-1. A seasonal comparison shows that up to 75% of midday anthropogenic carbon flux is removed via photosynthesis in the dominant wind sector, S, which bears typical tree canopy covers of 25-50% on pervious surfaces.

Verification and Validation of the Spring Model Parachute Air Delivery System in Subsonic Flow

DTIC Science & Technology

2015-02-27

putational challenges in handling the geometric complexities of the parachute canopy and the contact between parachutes in a cluster. Kim and Peskin et...Runge-Kutta method with numerical flux evaluated by 5-th order WENO scheme. The equations for k and ε are discretized with Crank -Nicolson scheme to...construction formula uk+1i = f ( uki−3, u k i−2, u k i−1, u k i , u k,poro i+1 , u k,poro i+2 , u k,poro i+3 ) . Diffusion part is solved using Crank

Comparison of WRF local and nonlocal boundary layer Physics in Greater Kuala Lumpur, Malaysia

NASA Astrophysics Data System (ADS)

Ooi, M. C. G.; Chan, A.; Kumarenthiran, S.; Morris, K. I.; Oozeer, M. Y.; Islam, M. A.; Salleh, S. A.

2018-02-01

The urban boundary layer (UBL) is the internal advection layer of atmosphere above urban region which determines the exchanges of momentum, water and other atmospheric constituents between the urban land surface and the free troposphere. This paper tested the performance of three planetary boundary layer (PBL) physics schemes of Weather Research and Forecast (WRF) software to ensure the appropriate representation of vertical structure of UBL in Greater Kuala Lumpur (GKL). Comparison was conducted on the performance of respective PBL schemes to generate vertical and near-surface weather profile and rainfall. Mellor-Yamada- Janjíc (MYJ) local PBL scheme coupled with Eta MM5 surface layer scheme was found to predict the near-surface temperature and wind profile and mixing height better than the nonlocal schemes during the intermonsoonal period with least influences of the synoptic background weather.

Feedbacks between Air-Quality, Meteorology, and the Forest Environment

NASA Astrophysics Data System (ADS)

Makar, Paul; Akingunola, Ayodeji; Stroud, Craig; Zhang, Junhua; Gong, Wanmin; Moran, Michael; Zheng, Qiong; Brook, Jeffrey; Sills, David

2017-04-01

The outcome of air quality forecasts depend in part on how the local environment surrounding the emissions regions influences chemical reaction rates and transport from those regions to the larger spatial scales. Forested areas alter atmospheric chemistry through reducing photolysis rates and vertical diffusivities within the forest canopy. The emitted pollutants, and their reaction products, are in turn capable of altering meteorology, through the well-known direct and indirect effects of particulate matter on radiative transfer. The combination of these factors was examined using version 2 of the Global Environmental Multiscale - Modelling Air-quality and CHemistry (GEM-MACH) on-line air pollution model. The model configuration used for this study included 12 aerosol size bins, eight aerosol species, homogeneous core Mie scattering, the Milbrandt-Yao two-moment cloud microphysics scheme with cloud condensation nuclei generated from model aerosols using the scheme of Abdul-Razzak and Ghan, and a new parameterization for forest canopy shading and turbulence. The model was nested to 2.5km resolution for a domain encompassing the lower Great Lakes, for simulations of a period in August of 2015 during the Pan American Games, held in Toronto, Canada. Four scenarios were carried out: (1) a "Base Case" scenario (the original model, in which coupling between chemistry and weather is not permitted; instead, the meteorological model's internal climatologies for aerosol optical and cloud condensation properties are used for direct and indirect effect calculations); (2) a "Feedback" scenario (the aerosol properties were derived from the internally simulated chemistry, and coupled to the meteorological model's radiative transfer and cloud formation modules); (3) a "Forest" scenario (canopy shading and turbulence were added to the Base Case); (4) a "Combined" scenario (including both direct and indirect effect coupling between meteorology and chemistry, as well as the forest canopy parameterization). The simulations suggest that the feedbacks between simulated aerosols and meteorology may strengthen the existing lake breeze circulation, modifying the resulting meteorological and air-quality forecasts, while the forest canopy's influence may extend throughout the planetary boundary layer, and may also influence the weather. The simulations will be compared to available observations, in order to determine their relative impact on model performance.

EnviroAtlas - New York, NY - One Meter Resolution Urban Land Cover Data (2008) Web Service

EPA Pesticide Factsheets

This EnviroAtlas web service supports research and online mapping activities related to EnviroAtlas (https://www.epa.gov/enviroatlas ). The New York, NY EnviroAtlas Meter-scale Urban Land Cover (MULC) Data were generated by the University of Vermont Spatial Analysis Laboratory (SAL) under the direction of Jarlath O'Neil-Dunne as part of the United States Forest Service Urban Tree Canopy (UTC) assessment program. Seven classes were mapped using LiDAR and high resolution orthophotography: Tree Canopy, Grass/Shrub, Bare Soil, Water, Buildings, Roads/Railroads, and Other Paved Surfaces. These data were subsequently merged to fit with the EPA classification. The SAL project covered the five boroughs within the NYC city limits. However the EPA study area encompassed that area plus a 1 kilometer buffer. Additional land cover for the buffer area was generated from United States Department of Agriculture (USDA) National Agricultural Imagery Program (NAIP) four band (red, green, blue, and near infrared) aerial photography at 1 m spatial resolution from July, 2011 and LiDAR from 2010. Six land cover classes were mapped: water, impervious surfaces, soil and barren land, trees, grass-herbaceous non-woody vegetation, and agriculture. An accuracy assessment of 600 completely random and 55 stratified random photo interpreted reference points yielded an overall User's fuzzy accuracy of 87 percent. The area mapped is the US Census Bureau's 2010 Urban Statistical Area for New Yor

Urban Domestic Gardens (XIV): The Characteristics of Gardens in Five Cities

NASA Astrophysics Data System (ADS)

Loram, Alison; Warren, Philip H.; Gaston, Kevin J.

2008-09-01

Domestic gardens make substantial contributions to the provision of green space in urban areas. However, the ecological functions provided by such gardens depend critically on their configuration and composition. Here, we present the first detailed analysis of variation in the composition of urban gardens, in relation to housing characteristics and the nature of the surrounding landscape, across different cities in the United Kingdom. In all five cities studied (Belfast, Cardiff, Edinburgh, Leicester, and Oxford), garden size had an overwhelming influence on garden composition. Larger gardens supported more of the land-use types recorded, in greater extents, and were more likely to contain particular features, including tall trees and mature shrubs, areas of unmown grass and uncultivated land, vegetable patches, ponds, and composting sites. The proportional contribution of non-vegetated land-uses decreased as garden area increased. House age was less significant in determining the land-use within gardens, although older houses, which were more likely to be found further from the urban edge of the city, contained fewer hedges and greater areas of vegetation canopy >2 m in height. Current UK government planning recommendations will ultimately reduce the area of individual gardens and are thus predicted to result in fewer tall trees and, in particular, less vegetation canopy >2 m. This might be detrimental from ecological, aesthetic, social, and economic stand points.

Modeling the interaction between plant canopies and the planetary boundary layer using a new 1D multi-layer soil- vegetation-atmosphere transfer (SVAT) scheme combined with a non-local turbulence closure model

NASA Astrophysics Data System (ADS)

Yetzer, Kenneth H.

A new one-dimensional (1D) soil-vegetation-atmospheric transport (SVAT) scheme is coupled to a nonlocal turbulence closure model in order to simulate the interactions between a forested canopy and the planetary boundary layer. The SVAT consists of mechanistic models for both physiological (photosynthesis, stomatal conductance and soil/root and bole respiration) and micrometeorological (radiative transfer and surface energy exchanges) processes. The turbulence closure model is a first-order, nonlocal turbulence closure called transilient turbulence theory (Stull, 1993; Inclan et al., 1995) which includes the effects of form drag, wake turbulence, and interference to vertical mixing by the plant elements. The submodel that accounts for radiative transfer inside the forest has been taken from Norman (1979) and Baldocchi (1989). It includes the effect of varying mean leaf inclination angle with height and it also accounts for leaf clumping The photosynthesis submodel is taken from Nikolov and others (1995). It accounts for both differences between shaded and sunlit leaves and the variation of photosynthetic capacity with height. The model was tested with data obtained from a deciduous forest in Pennsylvania. The results show reasonable agreement with the observations. They also demonstrate the model's ability to simulate phenomena that is characteristic of tall canopies like forests, including counter gradient-fluxes and local wind speed maxima in the trunk space.

Attribution of local climate zones using a multitemporal land use/land cover classification scheme

NASA Astrophysics Data System (ADS)

Wicki, Andreas; Parlow, Eberhard

2017-04-01

Worldwide, the number of people living in an urban environment exceeds the rural population with increasing tendency. Especially in relation to global climate change, cities play a major role considering the impacts of extreme heat waves on the population. For urban planners, it is important to know which types of urban structures are beneficial for a comfortable urban climate and which actions can be taken to improve urban climate conditions. Therefore, it is essential to differ between not only urban and rural environments, but also between different levels of urban densification. To compare these built-up types within different cities worldwide, Stewart and Oke developed the concept of local climate zones (LCZ) defined by morphological characteristics. The original LCZ scheme often has considerable problems when adapted to European cities with historical city centers, including narrow streets and irregular patterns. In this study, a method to bridge the gap between a classical land use/land cover (LULC) classification and the LCZ scheme is presented. Multitemporal Landsat 8 data are used to create a high accuracy LULC map, which is linked to the LCZ by morphological parameters derived from a high-resolution digital surface model and cadastral data. A bijective combination of the different classification schemes could not be achieved completely due to overlapping threshold values and the spatially homogeneous distribution of morphological parameters, but the attribution of LCZ to the LULC classification was successful.

44. May 1948 Threequarter port stern view under way at ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. May 1948 Three-quarter port stern view under way at U.S. Naval Shipyard, Charleston, South Carolina. Note paint scheme and canopy over large turtle deck at stern. - U.S. Coast Guard Cutter WHITE SUMAC, U.S. Coast Guard 8th District Base, 4640 Urquhart Street, New Orleans, Orleans Parish, LA

A thermal-based remote sensing modelling system for estimating crop water use and stress from field to regional scales

USDA-ARS?s Scientific Manuscript database

Thermal-infrared remote sensing of land surface temperature provides valuable information for quantifying root-zone water availability, evapotranspiration (ET) and crop condition. A thermal-based scheme, called the Two-Source Energy Balance (TSEB) model, solves for the soil/substrate and canopy temp...

Making direct use of canopy profiles in vegetation - atmosphere coupling

NASA Astrophysics Data System (ADS)

Ryder, James; Polcher, Jan; Peylin, Philippe; Ottlé, Catherine; Chen, Yiying; van Gorsel, Eva; Haverd, Vanessa; McGrath, Matthew; Naudts, Kim; Otto, Juliane; Valade, Aude; Luyssaert, Sebastiaan

2015-04-01

Most coupled land-surface regional models use the 'big-leaf' approach for simulating the sensible and latent heat fluxes of different vegetation types. However, there has been a progression in the types of questions being asked of these models, such as the consequences of land-use change or the behaviour of BVOCs and aerosol. In addition, recent years has seen growth in the availability of in-canopy datasets across a broaded range of species, with which to calibrate these simulations. Hence, there is now an argument for transferring some of the techniques and processes previously used in local, site-based land surface models to the land surface components of models which operate on a regional or even global scale. We describe here the development and evaluation of a vertical canopy energy budget model (Ryder, J et al., 2014) that can be coupled to an atmospheric model such as LMDz. Significantly, the model preserves the implicit coupling of the land-surface to atmosphere interface, which means that run-time efficiences are preserved. This is acheived by means of an interface based on the approach of Polcher et al. (1998) and Best et al. (2004), but newly developed for a canopy column. The model makes use of techniques from site-based models, such as the calculation of vertical turbulence statistics using a second-order closure model (Massman & Weil, 1999), and the distribution of long-wave and short-wave radiation over the profile, the latter using an innovate multilayer albedo scheme (McGrath et al., in prep.). Complete profiles of atmospheric temperature and specific humidity are now calculated, in order to simulate sensible and latent heat fluxes, as well as the leaf temperature at each level in the model. The model is shown to perform stably, and reproduces well flux measurements at an initial test site, across a time period of several days, or over the course of a year. Further applications of the model might be to simulate mixed canopies, the light-stimulated emission of chemical species, or the ecological consequences of changes to temperature profile as a results of changes to stand structure. References: Best, M. J., Beljaars, A. C. M., Polcher, J., & Viterbo, P. (2004). A proposed structure for coupling tiled surfaces with the planetary boundary layer. Journal of Hydrometeorology, 5, 1271-1278. Massman, W. J., & Weil, J. C., 1999. 'An analytical one-dimensional second-order closure model of turbulence statistics and the lagrangian time scale within and above plant canopies of arbitrary structure', Boundary-Layer Meteorology, 91, 81-107. Mcgrath, M. J., Pinty, B., Ryder, J., Otto, J., & Luyssaert, S., in prep. A multilevel canopy radiative transfer scheme based on a domain-averaged structure factor Polcher, J., McAvaney, B., Viterbo, P., Gaertner, M., Hahmann, A., Mahfouf, J.-F., Noilhan, J., Phillips, T.J., Pitman, A. J., Schlosser, C. A., Schulz, J-P, Timbal, B., Verseghy, D. L., Xue, Y. (1998). A proposal for a general interface between land surface schemes and general circulation models. Global and Planetary Change, 19, 261-276. Ryder, J., J. Polcher, P. Peylin, C. Ottlé, Y. Chen, E. Van Gorsel, V. Haverd, M. J. McGrath, K.Naudts, J. Otto, A. Valade, and S. Luyssaert, 2014. 'A multi-layer land surface energy budget model for implicit coupling with global atmospheric simulations', Geosci. Model Dev. Discuss. 7, 8649-8701

Persistence of long-distance, insect-mediated pollen movement for a tropical canopy tree species in remnant forest patches in an urban landscape.

PubMed

Noreen, A M E; Niissalo, M A; Lum, S K Y; Webb, E L

2016-12-01

As deforestation and urbanization continue at rapid rates in tropical regions, urban forest patches are essential repositories of biodiversity. However, almost nothing is known about gene flow of forest-dependent tree species in urban landscapes. In this study, we investigated gene flow in the insect-pollinated, wind-dispersed tropical tree Koompassia malaccensis in and among three remnant forest patches in the urbanized landscape of Singapore. We genotyped the vast majority of adults (N=179) and a large number of recruits (N=2103) with 8 highly polymorphic microsatellite markers. Spatial genetic structure of the recruit and adult cohorts was significant, showing routine gene dispersal distances of ~100-400 m. Parentage analysis showed that 97% of recruits were within 100 m of their mother tree, and a high frequency of relatively short-distance pollen dispersal (median ~143-187 m). Despite routine seed and pollen dispersal distances of within a few hundred meters, interpatch gene flow occurred between all patches and was dominated by pollen movement: parentage analysis showed 76 pollen versus 2 seed interpatch dispersal events, and the seedling neighborhood model estimated ~1-6% seed immigration and ~21-46% pollen immigration rates, depending on patch. In addition, the smallest patch (containing five adult K. malaccensis trees) was entirely surrounded by >2.5 km of 'impervious' substrate, yet had the highest proportional pollen and seed immigration estimates of any patch. Hence, contrary to our hypothesis, insect-mediated gene flow persisted across an urban landscape, and several of our results also parallel key findings from insect-pollinated canopy trees sampled in mixed agricultural-forest landscapes.

Modelling Pollutant Dispersion in a Street Network

NASA Astrophysics Data System (ADS)

Salem, N. Ben; Garbero, V.; Salizzoni, P.; Lamaison, G.; Soulhac, L.

2015-04-01

This study constitutes a further step in the analysis of the performances of a street network model to simulate atmospheric pollutant dispersion in urban areas. The model, named SIRANE, is based on the decomposition of the urban atmosphere into two sub-domains: the urban boundary layer, whose dynamics is assumed to be well established, and the urban canopy, represented as a series of interconnected boxes. Parametric laws govern the mass exchanges between the boxes under the assumption that the pollutant dispersion within the canopy can be fully simulated by modelling three main bulk transfer phenomena: channelling along street axes, transfers at street intersections, and vertical exchange between street canyons and the overlying atmosphere. Here, we aim to evaluate the reliability of the parametrizations adopted to simulate these phenomena, by focusing on their possible dependence on the external wind direction. To this end, we test the model against concentration measurements within an idealized urban district whose geometrical layout closely matches the street network represented in SIRANE. The analysis is performed for an urban array with a fixed geometry and a varying wind incidence angle. The results show that the model provides generally good results with the reference parametrizations adopted in SIRANE and that its performances are quite robust for a wide range of the model parameters. This proves the reliability of the street network approach in simulating pollutant dispersion in densely built city districts. The results also show that the model performances may be improved by considering a dependence of the wind fluctuations at street intersections and of the vertical exchange velocity on the direction of the incident wind. This opens the way for further investigations to clarify the dependence of these parameters on wind direction and street aspect ratios.

Modeling Transport of Turbulent Fluxes in a Heterogeneous Urban Canopy Using a Spatially Explicit Energy Balance

NASA Astrophysics Data System (ADS)

Moody, M.; Bailey, B.; Stoll, R., II

2017-12-01

Understanding how changes in the microclimate near individual plants affects the surface energy budget is integral to modeling land-atmosphere interactions and a wide range of near surface atmospheric boundary layer phenomena. In urban areas, the complex geometry of the urban canopy layer results in large spatial deviations of turbulent fluxes further complicating the development of models. Accurately accounting for this heterogeneity in order to model urban energy and water use requires a sub-plant level understanding of microclimate variables. We present analysis of new experimental field data taken in and around two Blue Spruce (Picea pungens) trees at the University of Utah in 2015. The test sites were chosen in order study the effects of heterogeneity in an urban environment. An array of sensors were placed in and around the conifers to quantify transport in the soil-plant-atmosphere continuum: radiative fluxes, temperature, sap fluxes, etc. A spatial array of LEMS (Local Energy Measurement Systems) were deployed to obtain pressure, surrounding air temperature and relative humidity. These quantities are used to calculate the radiative and turbulent fluxes. Relying on measurements alone is insufficient to capture the complexity of microclimate distribution as one reaches sub-plant scales. A spatially-explicit radiation and energy balance model previously developed for deciduous trees was extended to include conifers. The model discretizes the tree into isothermal sub-volumes on which energy balances are performed and utilizes incoming radiation as the primary forcing input. The radiative transfer component of the model yields good agreement between measured and modeled upward longwave and shortwave radiative fluxes. Ultimately, the model was validated through an examination of the full energy budget including radiative and turbulent fluxes through isolated Picea pungens in an urban environment.

Structure of a forested urban park: implications for strategic management.

PubMed

Millward, Andrew A; Sabir, Senna

2010-11-01

Informed management of urban parks can provide optimal conditions for tree establishment and growth and thus maximize the ecological and aesthetic benefits that trees provide. This study assesses the structure, and its implications for function, of the urban forest in Allan Gardens, a 6.1 ha downtown park in the City of Toronto, Canada, using the Street Tree Resource Analysis Tool for Urban Forest Managers (STRATUM). Our goal is to present a framework for collection and analysis of baseline data that can inform a management strategy that would serve to protect and enhance this significant natural asset. We found that Allan Garden's tree population, while species rich (43), is dominated by maple (Acer spp.) (48% of all park trees), making it reliant on very few species for the majority of its ecological and aesthetic benefits and raising disease and pest-related concerns. Age profiles (using size as a proxy) showed a dominance of older trees with an inadequate number of individuals in the young to early middle age cohort necessary for short- to medium-term replacement. Because leaf area represents the single-most important contributor to urban tree benefits modelling, we calculated it separately for every park tree, using hemispheric photography, to document current canopy condition. These empirical measurements were lower than estimates produced by STRATUM, especially when trees were in decline and lacked full canopies, highlighting the importance of individual tree condition in determining leaf area and hence overall forest benefits. Stewardship of natural spaces within cities demands access to accurate and timely resource-specific data. Our work provides an uncomplicated approach to the acquisition and interpretation of these data in the context of a forested urban park. Copyright 2010 Elsevier Ltd. All rights reserved.

Urbanization Effects on the Vertical Distribution of Soil Microbial Communities and Soil C Storage across Edge-to-Interior Urban Forest Gradients

NASA Astrophysics Data System (ADS)

Rosier, C. L.; Van Stan, J. T., II; Trammell, T. L.

2017-12-01

Urbanization alters environmental conditions such as temperature, moisture, carbon (C) and nitrogen (N) deposition affecting critical soil processes (e.g., C storage). Urban soils experience elevated N deposition (e.g., transportation, industry) and decreased soil moisture via urban heat island that can subsequently alter soil microbial community structure and activity. However, there is a critical gap in understanding how increased temperatures and pollutant deposition influences soil microbial community structure and soil C/N cycling in urban forests. Furthermore, canopy structural differences between individual tree species is a potentially important mechanism facilitating the deposition of pollutants to the soil. The overarching goal of this study is to investigate the influence of urbanization and tree species structural differences on the bacterial and fungal community and C and N content of soils experiencing a gradient of urbanization pressures (i.e., forest edge to interior; 150-m). Soil cores (1-m depth) were collected near the stem (< 0.5 meter) of two tree species with contrasting canopy and bark structure (Fagus grandifolia, vs. Liriodendron tulipifera), and evaluated for soil microbial structure via metagenomic analysis and soil C/N content. We hypothesize that soil moisture constraints coupled with increases in recalcitrant C will decrease gram negative bacteria (i.e., dependent on labile C) while increasing saprophytic fungal community abundance (i.e., specialist consuming recalcitrant C) within both surface and subsurface soils experiencing the greatest urban pressure (i.e., forest edge). We further expect trees located on the edge of forest fragments will maintain greater surface soil (< 20 cm) C concentrations due to decreased soil moisture constraining microbial activity (e.g., slower decay), and increased capture of recalcitrant C stocks from industrial/vehicle emission sources (e.g., black C). Our initial results support our hypotheses that urbanization alters soil microbial community composition via reduced soil moisture and carbon storage potential via deposition gradients. Further analyses will answer important questions regarding how individual tree species alters urban soil C storage, N retention, and microbial dynamics.

Utilising green and bluespace to mitigate urban heat island intensity.

PubMed

Gunawardena, K R; Wells, M J; Kershaw, T

2017-04-15

It has long been recognised that cities exhibit their own microclimate and are typically warmer than the surrounding rural areas. This 'mesoscale' influence is known as the urban heat island (UHI) effect and results largely from modification of surface properties leading to greater absorption of solar radiation, reduced convective cooling and lower water evaporation rates. Cities typically contain less vegetation and bodies of water than rural areas, and existing green and bluespace is often under threat from increasing population densities. This paper presents a meta-analysis of the key ways in which green and bluespace affect both urban canopy- and boundary-layer temperatures, examined from the perspectives of city-planning, urban climatology and climate science. The analysis suggests that the evapotranspiration-based cooling influence of both green and bluespace is primarily relevant for urban canopy-layer conditions, and that tree-dominated greenspace offers the greatest heat stress relief when it is most needed. However, the magnitude and transport of cooling experienced depends on size, spread, and geometry of greenspaces, with some solitary large parks found to offer minimal boundary-layer cooling. Contribution to cooling at the scale of the urban boundary-layer climate is attributed mainly to greenspace increasing surface roughness and thereby improving convection efficiency rather than evaporation. Although bluespace cooling and transport during the day can be substantial, nocturnal warming is highlighted as likely when conditions are most oppressive. However, when both features are employed together they can offer many synergistic ecosystem benefits including cooling. The ways in which green and bluespace infrastructure is applied in future urban growth strategies, particularly in countries expected to experience rapid urbanisation, warrants greater consideration in urban planning policy to mitigate the adverse effects of the UHI and enhance climate resilience. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

The Role of Vegetation and Mulch in Mitigating the Impact of Raindrops on Soils in Urban Vegetated Green Infrastructure Systems

NASA Astrophysics Data System (ADS)

Alizadehtazi, B.; Montalto, F. A.; Sjoblom, K.

2014-12-01

Raindrop impulses applied to soils can break up larger soil aggregates into smaller particles, dispersing them from their original position. The displaced particles can self-stratify, with finer particles at the top forming a crust. Occurrence of this phenomenon reduces the infiltration rate and increases runoff, contributing to downstream flooding, soil erosion, and non point source pollutant loads. Unprotected soil surfaces (e.g. without vegetation canopies, mulch, or other materials), are more susceptible to crust formation due to the higher kinetic energy associated with raindrop impact. By contrast, soil that is protected by vegetation canopies and mulch layers is less susceptible to crust formation, since these surfaces intercept raindrops, dissipating some of their kinetic energy prior to their impact with the soil. Within this context, this presentation presents preliminary laboratory work conducted using a rainfall simulator to determine the ability of new urban vegetation and mulch to minimize soil crust formation. Three different scenarios are compared: a) bare soil, b) soil with mulch cover, and c) soil protected by vegetation canopies. Soil moisture, surface penetration resistance, and physical measurements of the volume of infiltrate and runoff are made on all three surface treatments after simulated rainfall events. The results are used to develop recommendations regarding surface treatment in green infrastructure (GI) system designs, namely whether heavily vegetated GI facilities require mulching to maintain infiltration capacity.

The Photochemical Reflectance Index from Directional Cornfield Reflectances: Observations and Simulations

NASA Technical Reports Server (NTRS)

Cheng, Yen-Ben; Middleton, Elizabeth M.; Zhang, Qingyuan; Corp, Lawrence A.; Dandois, Jonathan; Kustas, William P.

2012-01-01

The two-layer Markov chain Analytical Canopy Reflectance Model (ACRM) was linked with in situ hyperspectral leaf optical properties to simulate the Photochemical Reflectance Index (PRI) for a corn crop canopy at three different growth stages. This is an extended study after a successful demonstration of PRI simulations for a cornfield previously conducted at an early vegetative growth stage. Consistent with previous in situ studies, sunlit leaves exhibited lower PRI values than shaded leaves. Since sunlit (shaded) foliage dominates the canopy in the reflectance hotspot (coldspot), the canopy PRI derived from field hyperspectral observations displayed sensitivity to both view zenith angle and relative azimuth angle at all growth stages. Consequently, sunlit and shaded canopy sectors were most differentiated when viewed along the azimuth matching the solar principal plane. These directional PRI responses associated with sunlit/shaded foliage were successfully reproduced by the ACRM. As before, the simulated PRI values from the current study were closer to in situ values when both sunlit and shaded leaves were utilized as model input data in a two-layer mode, instead of a one-layer mode with sunlit leaves only. Model performance as judged by correlation between in situ and simulated values was strongest for the mature corn crop (r = 0.87, RMSE = 0.0048), followed by the early vegetative stage (r = 0.78; RMSE = 0.0051) and the early senescent stage (r = 0.65; RMSE = 0.0104). Since the benefit of including shaded leaves in the scheme varied across different growth stages, a further analysis was conducted to investigate how variable fractions of sunlit/shaded leaves affect the canopy PRI values expected for a cornfield, with implications for 20 remote sensing monitoring options. Simulations of the sunlit to shaded canopy ratio near 50/50 +/- 10 (e.g., 60/40) matching field observations at all growth stages were examined. Our results suggest in the importance of the sunlit/shaded fraction and canopy structure in understanding and interpreting PRI.

A data-led comparison of simple canopy radiative transfer models for the boreal forest

NASA Astrophysics Data System (ADS)

Reid, T.; Essery, R.; Rutter, N.; King, M.

2012-12-01

Given the computational complexity of numerical weather and climate models, it is worthwhile developing very simple parameterizations for processes such as the transmission of radiation through forest canopies. For this reason, the land surface schemes in global models, and most snow hydrological models, tend to use simple one-dimensional approaches based on Beer's Law or two-stream approximations. Such approaches assume a continuous canopy structure that may not be suitable for the varied, heterogeneous forest cover in boreal regions, especially in winter when snow in the canopy and on the ground may either block radiation or produce multiple reflections between the ground and the trees. There is great benefit in comparing models to real transmissivity values calculated from radiation measurements below and above Arctic canopies. In particular, there is a lack of data for leafless boreal deciduous forests, where canopy gaps are prevalent even at low solar elevation angles near the horizon. In this study, models are compared to radiation data collected in an area of boreal birch forest near Abisko, Sweden in March/April 2011 and mixed conifer forest at Sodankylä, Finland in March/April 2012. Arrays comprising ten shortwave pyranometers were deployed for periods of up to 50 days, under forest plots of varying canopy structures and densities. In addition, global and diffuse shortwave irradiances were recorded at nearby open sites representing the top-of-canopy conditions. A model is developed that explicitly accounts for both diffuse radiation and direct beam transmission on a 5-minute timestep, by using upward-looking hemispherical photographs taken from every pyranometer site. This model reproduces measured transmissivity, although with a slight underestimation, especially at low solar elevations - this could be attributed to multiple reflections that are not accounted for in the model. On the other hand, models based on Beer's Law tend to underestimate the canopy transmissivity significantly, especially for leafless birch canopies where the required assumption of a continuous canopy breaks down. These findings are important for the often sparse, heterogeneous forest cover in boreal regions, where forest edges and canopy gaps are plentiful. They could also have an impact on estimations of overall land surface albedo. Moreover, all models are sensitive to the partitioning of top-of-canopy radiation into its direct and diffuse components, which is complicated by the low solar elevations in the Arctic. More research is required to decide the best way of quantifying the diffuse fraction, using data alongside both physical and empirical models.

Volatile organic compounds sources and sinks in a wheat canopy. Analysis based on combined eddy-covariance fluxes, in-canopy profiles and chamber measurements with a PTR-TOF-Qi-MS

NASA Astrophysics Data System (ADS)

Loubet, Benjamin; Gonzaga, Lais; Buysse, Pauline; Ciuraru, Raluca; Lafouge, Florence; Decuq, Céline; Zurfluh, Olivier; Fortineau, Alain; Fanucci, Olivier; Sarda-Esteve, Roland; Zannoni, Nora; Truong, Francois; Boissard, Christophe; Gros, Valérie

2017-04-01

Volatile organic compounds (VOC) are essential drivers of atmospheric chemistry. Many VOCs are emitted from and deposited to ecosystems. While forests and grasslands have already been substantially studied, exchanges of VOCs with crops are less known, although these ecosystems represent more than 50% of the surface in France. In this study, we analyze sources and sinks of VOCs in a wheat field (at the ICOS FR-GRI site near Paris) at anthesis based on measurements of fluxes, concentration profiles and branch chambers. The VOCs were measured using a PTR-TOF-Qi-MS (where Qi stands for Quad Ion guide). Air was successively sampled through lines located at different heights within and above the canopy, of which one was used for Eddy Covariance and located near a sonic anemometer. Additional measurements included the standard ICOS meteorological data as well as leaf area index profiles and photosynthesis curves at several heights in the canopy. We report fluxes and profiles for more than 500 VOCs. The deposition velocities of depositing compounds are compared to the maximum exchange velocity and the ozone deposition velocity. The sources and sinks location and magnitude are evaluated by inverse Lagrangian modelling assuming no reaction and simple reaction schemes in the canopy. The sources and sinks of VOC in the canopy are interpreted in terms crop phenology and the potential for reaction with ozone and NOx is evaluated. This study takes place in the ADEME CORTEA COV3ER French project (http://www6.inra.fr/cov3er).

Crowdsourcing urban air temperatures from smartphone battery temperatures

NASA Astrophysics Data System (ADS)

Overeem, A.; Robinson, J. C. R.; Leijnse, H.; Steeneveld, G. J.; Horn, B. K. P.; Uijlenhoet, R.

2013-08-01

Accurate air temperature observations in urban areas are important for meteorology and energy demand planning. They are indispensable to study the urban heat island effect and the adverse effects of high temperatures on human health. However, the availability of temperature observations in cities is often limited. Here we show that relatively accurate air temperature information for the urban canopy layer can be obtained from an alternative, nowadays omnipresent source: smartphones. In this study, battery temperatures were collected by an Android application for smartphones. A straightforward heat transfer model is employed to estimate daily mean air temperatures from smartphone battery temperatures for eight major cities around the world. The results demonstrate the enormous potential of this crowdsourcing application for real-time temperature monitoring in densely populated areas.

Application of Intel Many Integrated Core (MIC) accelerators to the Pleim-Xiu land surface scheme

NASA Astrophysics Data System (ADS)

Huang, Melin; Huang, Bormin; Huang, Allen H.

2015-10-01

The land-surface model (LSM) is one physics process in the weather research and forecast (WRF) model. The LSM includes atmospheric information from the surface layer scheme, radiative forcing from the radiation scheme, and precipitation forcing from the microphysics and convective schemes, together with internal information on the land's state variables and land-surface properties. The LSM is to provide heat and moisture fluxes over land points and sea-ice points. The Pleim-Xiu (PX) scheme is one LSM. The PX LSM features three pathways for moisture fluxes: evapotranspiration, soil evaporation, and evaporation from wet canopies. To accelerate the computation process of this scheme, we employ Intel Xeon Phi Many Integrated Core (MIC) Architecture as it is a multiprocessor computer structure with merits of efficient parallelization and vectorization essentials. Our results show that the MIC-based optimization of this scheme running on Xeon Phi coprocessor 7120P improves the performance by 2.3x and 11.7x as compared to the original code respectively running on one CPU socket (eight cores) and on one CPU core with Intel Xeon E5-2670.

Sensitivity of Climate Simulations to Land-Surface and Atmospheric Boundary-Layer Treatments-A Review.

NASA Astrophysics Data System (ADS)

Garratt, J. R.

1993-03-01

Aspects of the land-surface and boundary-layer treatments in some 20 or so atmospheric general circulation models (GCMS) are summarized. In only a small fraction of these have significant sensitivity studies been carried out and published. Predominantly, the sensitivity studies focus upon the parameterization of land-surface processes and specification of land-surface properties-the most important of these include albedo, roughness length, soil moisture status, and vegetation density. The impacts of surface albedo and soil moisture upon the climate simulated in GCMs with bare-soil land surfaces are well known. Continental evaporation and precipitation tend to decrease with increased albedo and decreased soil moisture availability. For example, results from numerous studies give an average decrease in continental precipitation of 1 mm day1 in response to an average albedo increase of 0.13. Few conclusive studies have been carried out on the impact of a gross roughness-length change-the primary study included an important statistical assessment of the impact upon the mean July climate around the globe of a decreased continental roughness (by three orders of magnitude). For example, such a decrease reduced the precipitation over Amazonia by 1 to 2 mm day1.The inclusion of a canopy scheme in a GCM ensures the combined impacts of roughness (canopies tend to be rougher than bare soil), albedo (canopies tend to be less reflective than bare soil), and soil-moisture availability (canopies prevent the near-surface soil region from drying out and can access the deep soil moisture) upon the simulated climate. The most revealing studies to date involve the regional impact of Amazonian deforestation. The results of four such studies show that replacing tropical forest with a degraded pasture results in decreased evaporation ( 1 mm day1) and precipitation (1-2 mm day1), and increased near-surface air temperatures (2 K).Sensitivity studies as a whole suggest the need for a realistic surface representation in general circulation models of the atmosphere. It is not yet clear how detailed this representation needs to be, but even allowing for the importance of surface processes, the parameterization of boundary-layer and convective clouds probably represents a greater challenge to improved climate simulations. This is illustrated in the case of surface net radiation for Aniazonia, which is not well simulated and tends to be overestimated, leading to evaporation rates that are too large. Underestimates in cloudiness, cloud albedo, and clear-sky shortwave absorption, rather than in surface albedo, appear to be the main culprits.There are three major tasks that confront the researcher so far as the development and validation of atmospheric boundary-layer (ABL) and surface schemes in GCMs are concerned:(i) There is a need to as' critically the impact of `improved' parameterization schemes on WM simulations, taking into account the problem of natural variability and hence the statistical significance of the induced changes.(ii) There is a need to compare GCM simulations of surface and ABL behavior (particularly regarding the diurnal cycle of surface fluxes, air temperature, and ABL depth) with observations over a range of surface types (vegetation, desert, ocean). In this context, area-average values of surface fluxes will be required to calibrate directly the ABL/land-surface scheme in the GCM.(iii) There is a need for intercomparisons of ABL and land-surface schemes used in GCMS, both for one- dimensional stand-alone models and for GCMs that incorporate the respective schemes.

Study of the effectiveness of several tree canopy types on roadside green belt in influencing the distribution of NO2 gas emitted from transportation

NASA Astrophysics Data System (ADS)

Desyana, R. D.; Sulistyantara, B.; Nasrullah, N.; Fatimah, I. S.

2017-03-01

Transportation is one significant factor which contributes to urban air pollution. One of the pollutants emitted from transportation which affect human’s health is NO2. Plants, especially trees, have high potential in reducing air pollutants from transportation through diffusion, absorbtion, adsorption and deposition. Purpose of this study was to analyze the effectiveness of several tree canopy types on roadside green belt in influencing distribution of NO2 gas emitted from transportation. The study conducted in three plots of tree canopy in Jagorawi Highway: Bungur (Lagerstroemia speciosa), Gmelina (Gmelina arborea) and Tanjung (Mimusops elengi). The tree canopy ability in absorbing pollutant is derived by comparing air quality on vegetated area with ambience air quality at control area (open field). Air sampling was conducted to measure NO2 concentration at elevation 1.5m, 5m and 10m at distance 0m, 10m and 30m, using Air Sampler Impinger. Concentration of NO2 was analyzed with Griess-Saltzman method. From this research, the result of ANOVA showed that tree plot (vegetated area) affected significantly to NO2 concentration. However the effect of distance from road and elevation was not significant. Among the plots, the highest NO2 concentration was found on Control plot (area without tree canopy), while the lowest NO2 concentration was found in Tanjung plot. Tanjung plot with round shape and high density canopy performed better in reducing NO2 than Bungur plot with round shape and medium density canopy, regardless the sampling elevation and distance. Gmelina plot performed the best in reducing horizontal distribution of NO2 concentration at elevation 1.5 and 5m, but the result at elevation 10m was not significant.

Impacts of Vegetation and Urban planning on micro climate in Hashtgerd new Town

NASA Astrophysics Data System (ADS)

Sodoudi, S.; Langer, I.; Cubasch, U.

2012-12-01

One of the objectives of climatological part of project Young Cities 'Developing Energy-Efficient Urban Fabric in the Tehran-Karaj Region' is to simulate the micro climate (with 1m resolution) in 35ha of new town Hashtgerd, which is located 65 km far from mega city Tehran. The Project aims are developing, implementing and evaluating building and planning schemes and technologies which allow to plan and build sustainable, energy-efficient and climate sensible form mass housing settlements in arid and semi-arid regions ("energy-efficient fabric"). Climate sensitive form also means designing and planning for climate change and its related effects for Hashtgerd New Town. By configuration of buildings and open spaces according to solar radiation, wind and vegetation, climate sensitive urban form can create outdoor thermal comfort. To simulate the climate on small spatial scales, the micro climate model Envi-met has been used to simulate the micro climate in 35 ha. The Eulerian model ENVI-met is a micro-scale climate model which gives information about the influence of architecture and buildings as well as vegetation and green area on the micro climate up to 1 m resolution. Envi-met has been run with information from topography, downscaled climate data with neuro-fuzzy method, meteorological measurements, building height and different vegetation variants (low and high number of trees) Through the optimal Urban Design and Planning for the 35ha area the micro climate results shows, that with vegetation the micro climate in street canopies will be change: - 2 m temperature is decreased by about 2 K - relative humidity increase by about 10 % - soil temperature is decreased by about 3 K - wind speed is decreased by about 60% The style of buildings allows free movement of air, which is of high importance for fresh air supply. The increase of inbuilt areas in 35 ha reduces the heat island effect through cooling caused by vegetation and increase of air humidity which caused by trees evaporation. The downscaled climate scenarios considering new urban planning strategies in 35ha will be presented till 2100.

Impacts of Vegetation and Urban planning on micro climate in Hashtgerd new Town

NASA Astrophysics Data System (ADS)

Sodoudi, Sahar; langer, Ines; Cubasch, Ulrich

2013-04-01

One of the objectives of climatological part of project Young Cities 'Developing Energy-Efficient Urban Fabric in the Tehran-Karaj Region' is to simulate the micro climate (with 1m resolution) in 35ha of new town Hashtgerd, which is located 65 km far from mega city Tehran. The Project aims are developing, implementing and evaluating building and planning schemes and technologies which allow to plan and build sustainable, energy-efficient and climate sensible form mass housing settlements in arid and semi-arid regions ("energy-efficient fabric"). Climate sensitive form also means designing and planning for climate change and its related effects for Hashtgerd New Town. By configuration of buildings and open spaces according to solar radiation, wind and vegetation, climate sensitive urban form can create outdoor thermal comfort. To simulate the climate on small spatial scales, the micro climate model Envi-met has been used to simulate the micro climate in 35 ha. The Eulerian model ENVI-met is a micro-scale climate model which gives information about the influence of architecture and buildings as well as vegetation and green area on the micro climate up to 1 m resolution. Envi-met has been run with information from topography, downscaled climate data with neuro-fuzzy method, meteorological measurements, building height and different vegetation variants (low and high number of trees) Through the optimal Urban Design and Planning for the 35ha area the microclimate results shows, that with vegetation the microclimate in street canopies will be change: • 2 m temperature is decreased by about 2 K • relative humidity increase by about 10 % • soil temperature is decreased by about 3 K • wind speed is decreased by about 60% The style of buildings allows free movement of air, which is of high importance for fresh air supply. The increase of inbuilt areas in 35 ha reduces the heat island effect through cooling caused by vegetation and increase of air humidity which caused by trees evaporation. The downscaled climate scenarios considering new urban planning strategies in 35ha will be presented till 2100.

Reach-scale effects of riparian forest cover on urban stream ecosystems

USGS Publications Warehouse

Roy, A.H.; Faust, C.L.; Freeman, Mary C.; Meyer, J.L.

2005-01-01

We compared habitat and biota between paired open and forested reaches within five small streams (basin area 10?20 km2) in suburban catchments (9%?49% urban land cover) in the Piedmont of Georgia, USA. Stream reaches with open canopies were narrower than forested reaches (4.1 versus 5.0 m, respectively). There were no differences in habitat diversity (variation in velocity, depth, or bed particle size) between open and forested reaches. However, absence of local forest cover corresponded to decreased large wood and increased algal chlorophyll a standing crop biomass. These differences in basal food resources translated into higher densities of fishes in open (9.0 individuals?m?2) versus forested (4.9 individuals?m?2) reaches, primarily attributed to higher densities of the herbivore Campostoma oligolepis. Densities of terrestrial invertebrate inputs were higher in open reaches; however, trends suggested higher biomass of terrestrial inputs in forested reaches and a corresponding higher density of terrestrial prey consumed by water column feeding fishes. Reach-scale biotic integrity (macroinvertebrates, salamanders, and fishes) was largely unaffected by differences in canopy cover. In urbanizing areas where catchment land cover drives habitat and biotic quality, management practices that rely exclusively on forested riparian areas for stream protection are unlikely to be effective at maintaining ecosystem integrity.

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

24 CFR 3285.702 - Miscellaneous lights and fixtures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed and...

EnviroAtlas - New York, NY - One Meter Resolution Urban Land Cover Data (2008)

EPA Pesticide Factsheets

The New York, NY EnviroAtlas Meter-scale Urban Land Cover (MULC) Data were generated by the University of Vermont Spatial Analysis Laboratory (SAL) under the direction of Jarlath O'Neil-Dunne as part of the United States Forest Service Urban Tree Canopy (UTC) assessment program. Seven classes were mapped using LiDAR and high resolution orthophotography: Tree Canopy, Grass/Shrub, Bare Soil, Water, Buildings, Roads/Railroads, and Other Paved Surfaces. These data were subsequently merged to fit with the EPA classification. The SAL project covered the five boroughs within the NYC city limits. However the EPA study area encompassed that area plus a 1 kilometer buffer. Additional land cover for the buffer area was generated from United States Department of Agriculture (USDA) National Agricultural Imagery Program (NAIP) four band (red, green, blue, and near infrared) aerial photography at 1 m spatial resolution from July, 2011 and LiDAR from 2010. Six land cover classes were mapped: water, impervious surfaces, soil and barren land, trees, grass-herbaceous non-woody vegetation, and agriculture. An accuracy assessment of 600 completely random and 55 stratified random photo interpreted reference points yielded an overall User's fuzzy accuracy of 87 percent. The area mapped is the US Census Bureau's 2010 Urban Statistical Area for New York City plus a 1 km buffer. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAt

Frequency analysis of urban runoff quality in an urbanizing catchment of Shenzhen, China

NASA Astrophysics Data System (ADS)

Qin, Huapeng; Tan, Xiaolong; Fu, Guangtao; Zhang, Yingying; Huang, Yuefei

2013-07-01

This paper investigates the frequency distribution of urban runoff quality indicators using a long-term continuous simulation approach and evaluates the impacts of proposed runoff control schemes on runoff quality in an urbanizing catchment in Shenzhen, China. Four different indicators are considered to provide a comprehensive assessment of the potential impacts: total runoff depth, event pollutant load, Event Mean Concentration, and peak concentration during a rainfall event. The results obtained indicate that urban runoff quantity and quality in the catchment have significant variations in rainfall events and a very high rate of non-compliance with surface water quality regulations. Three runoff control schemes with the capacity to intercept an initial runoff depth of 5 mm, 10 mm, and 15 mm are evaluated, respectively, and diminishing marginal benefits are found with increasing interception levels in terms of water quality improvement. The effects of seasonal variation in rainfall events are investigated to provide a better understanding of the performance of the runoff control schemes. The pre-flood season has higher risk of poor water quality than other seasons after runoff control. This study demonstrates that frequency analysis of urban runoff quantity and quality provides a probabilistic evaluation of pollution control measures, and thus helps frame a risk-based decision making for urban runoff quality management in an urbanizing catchment.

An ecohydrologic model for a shallow groundwater urban environment.

PubMed

Arden, Sam; Ma, Xin Cissy; Brown, Mark

2014-01-01

The urban environment is a patchwork of natural and artificial surfaces that results in complex interactions with and impacts to natural hydrologic cycles. Evapotranspiration is a major hydrologic flow that is often altered through urbanization, although the mechanisms of change are sometimes difficult to tease out due to difficulty in effectively simulating soil-plant-atmosphere interactions. This paper introduces a simplified yet realistic model that is a combination of existing surface runoff and ecohydrology models designed to increase the quantitative understanding of complex urban hydrologic processes. Results demonstrate that the model is capable of simulating the long-term variability of major hydrologic fluxes as a function of impervious surface, temperature, water table elevation, canopy interception, soil characteristics, precipitation and complex mechanisms of plant water uptake. These understandings have potential implications for holistic urban water system management.

A Large Scale Biorational Approach Using Bacillus thuringiensis israeliensis (Strain AM65-52) for Managing Aedes aegypti Populations to Prevent Dengue, Chikungunya and Zika Transmission

PubMed Central

Pruszynski, Catherine A.; Hribar, Lawrence J.; Mickle, Robert; Leal, Andrea L.

2017-01-01

Background Aedes aegypti is a container-inhabiting mosquito and a vector of dengue, chikungunya, and Zika viruses. In 2009 several cases of autochthonous dengue transmission were reported in Key West, Florida, USA prompting a comprehensive response to control A. aegypti. In Key West, larvae of this mosquito develop in containers around human habitations which can be numerous and labor intensive to find and treat. Aerial applications of larvicide covering large areas in a short time can be an efficient and economical method to control A. aegypti. Bacillus thuringiensis israelensis (Bti) is a bacterial larvicide which is highly target specific and appropriate for wide area spraying over urban areas, but to date, there are no studies that evaluate aerial spraying of Bti to control container mosquitoes like A. aegypti. Methodology This paper examines the effectiveness of aerial larvicide applications using VectoBac® WG, a commercially available Bti formulation, for A. aegypti control in an urban setting in the USA. Droplet characteristics and spray drop deposition were evaluated in Key West, Florida, USA. The mortality of A. aegypti in containers placed under canopy in an urban environment was also evaluated. Efficacy of multiple larvicide applications on adult female A. aegypti population reduction was compared between an untreated control and treatment site. Conclusions Droplet characteristics showed that small droplets can penetrate through dense canopy to reach small containers. VectoBac WG droplets reached small containers under heavy canopy in sufficient amounts to cause > 55% mortality on all application days and >90% mortality on 3 of 5 application days while controls had <5% mortality. Aerial applications of VectoBac WG caused significant decrease in adult female populations throughout the summer and during the 38th week (last application) the difference in adult female numbers between untreated and treated sites was >50%. Aerial larvicide applications using VectoBac WG can cover wide areas in a short period of time and can be effective in controlling A. aegypti and reducing A. aegypti-borne transmission in urban areas similar to Key West, Florida, USA. PMID:28199323

Loss of urban forest canopy and the related effects on soundscape and human directed attention

NASA Astrophysics Data System (ADS)

Laverne, Robert James Paul

The specific questions addressed in this research are: Will the loss of trees in residential neighborhoods result in a change to the local soundscape? The investigation of this question leads to a related inquiry: Do the sounds of the environment in which a person is present affect their directed attention?. An invasive insect pest, the Emerald Ash Borer (Agrilus planipennis ), is killing millions of ash trees (genus Fraxinus) throughout North America. As the loss of tree canopy occurs, urban ecosystems change (including higher summer temperatures, more stormwater runoff, and poorer air quality) causing associated changes to human physical and mental health. Previous studies suggest that conditions in urban environments can result in chronic stress in humans and fatigue to directed attention, which is the ability to focus on tasks and to pay attention. Access to nature in cities can help refresh directed attention. The sights and sounds associated with parks, open spaces, and trees can serve as beneficial counterbalances to the irritating conditions associated with cities. This research examines changes to the quantity and quality of sounds in Arlington Heights, Illinois. A series of before-and-after sound recordings were gathered as trees died and were removed between 2013 and 2015. Comparison of recordings using the Raven sound analysis program revealed significant differences in some, but not all measures of sound attributes as tree canopy decreased. In general, more human-produced mechanical sounds (anthrophony) and fewer sounds associated with weather (geophony) were detected. Changes in sounds associated with animals (biophony) varied seasonally. Monitoring changes in the proportions of anthrophony, biophony and geophony can provide insight into changes in biodiversity, environmental health, and quality of life for humans. Before-tree-removal and after-tree-removal sound recordings served as the independent variable for randomly-assigned human volunteers as they performed the Stroop Test and the Necker Cube Pattern Control test to measure directed attention. The sound treatments were not found to have significant effects on the directed attention test scores. Future research is needed to investigate the characteristics of urban soundscapes that are detrimental or potentially conducive to human cognitive functioning.

Estimation of Anthropogenic Heat Emissions in Delhi, India and Their Role in Urban Heat Island Effect

NASA Astrophysics Data System (ADS)

Bhati, S.; Mohan, M.

2016-12-01

Energy consumption in the urban environment impacts the urban surface energy budget and leads to the emission of anthropogenic sensible heat into the atmosphere. Anthropogenic heat (AH) can vary both in time and space, and are not readily measured. In present study, anthropogenic heat emissions have been estimated using an inventory approach for Delhi. The main sources that have been considered are electricity consumption, vehicular emissions, fuel consumption in domestic sector and waste heat from power plants. Total estimated anthropogenic heat is apportioned gridwise (2 km2) and incorporated in the WRF (version 3.5) model coupled with single-layer Urban canopy model (UCM) to assess the impact of these emissions on urban heat island effect in Delhi. Vehicular emissions have been found to be highest contributor to anthropogenic heat emissions (47%) followed by electricity consumption (28%), domestic fuel consumption (16%) and waste heat from power plants (9%). Highest annual average anthropogenic heat flux was estimated to be 25.2 Wm-2. High flux zones are observed in east Delhi and densely occupied and commercial zones of Sitaram Bazar and Connaught Place. Inclusion of anthropogenic heat emissions in the model improves model performance for near surface temperature as well as urban heat island intensities. Maximum simulated night-time UHI improves from 5.95°C (without AH) to 6.24°C (with AH) against observed value of 6.68°C, thereby indicating positive contribution of anthropogenic heat emissions along with urban canopy towards UHI effect in Delhi. Similarly, spatial distribution and UHI hotspots are found to be comparatively closer to corresponding observed distribution and hotspots with anthropogenic heat emissions being added to the WRF model. Overall, relatively improved model performance is indicative of the impact of anthropogenic heat emissions in local urban meteorology and urban heat island effect in Delhi. Hence, rising population and change in land use-cover and associated anthropogenic activities call for strategic mitigation measures in the city to prevent further strengthening of heat island effect.

Conjunctively optimizing flash flood control and water quality in urban water reservoirs by model predictive control and dynamic emulation

NASA Astrophysics Data System (ADS)

Galelli, Stefano; Goedbloed, Albert; Schmitter, Petra; Castelletti, Andrea

2014-05-01

Urban water reservoirs are a viable adaptation option to account for increasing drinking water demand of urbanized areas as they allow storage and re-use of water that is normally lost. In addition, the direct availability of freshwater reduces pumping costs and diversifies the portfolios of drinking water supply. Yet, these benefits have an associated twofold cost. Firstly, the presence of large, impervious areas increases the hydraulic efficiency of urban catchments, with short time of concentration, increased runoff rates, losses of infiltration and baseflow, and higher risk of flash floods. Secondly, the high concentration of nutrients and sediments characterizing urban discharges is likely to cause water quality problems. In this study we propose a new control scheme combining Model Predictive Control (MPC), hydro-meteorological forecasts and dynamic model emulation to design real-time operating policies that conjunctively optimize water quantity and quality targets. The main advantage of this scheme stands in its capability of exploiting real-time hydro-meteorological forecasts, which are crucial in such fast-varying systems. In addition, the reduced computational requests of the MPC scheme allows coupling it with dynamic emulators of water quality processes. The approach is demonstrated on Marina Reservoir, a multi-purpose reservoir located in the heart of Singapore and characterized by a large, highly urbanized catchment with a short (i.e. approximately one hour) time of concentration. Results show that the MPC scheme, coupled with a water quality emulator, provides a good compromise between different operating objectives, namely flood risk reduction, drinking water supply and salinity control. Finally, the scheme is used to assess the effect of source control measures (e.g. green roofs) aimed at restoring the natural hydrological regime of Marina Reservoir catchment.

The Urban Tree as a Tool to Mitigate the Urban Heat Island in Mexico City: A Simple Phenomenological Model.

PubMed

Ballinas, Mónica; Barradas, Víctor L

2016-01-01

The urban heat island (UHI) is mainly a nocturnal phenomenon, but it also appears during the day in Mexico City. The UHI may affect human thermal comfort, which can influence human productivity and morbidity in the spring/summer period. A simple phenomenological model based on the energy balance was developed to generate theoretical support of UHI mitigation in Mexico City focused on the latent heat flux change by increasing tree coverage to reduce sensible heat flux and air temperature. Half-hourly data of the urban energy balance components were generated in a typical residential/commercial neighborhood of Mexico City and then parameterized using easily measured variables (air temperature, humidity, pressure, and visibility). Canopy conductance was estimated every hour in four tree species, and transpiration was estimated using sap flow technique and parameterized by the envelope function method. Averaged values of net radiation, energy storage, and sensible and latent heat flux were around 449, 224, 153, and 72 W m, respectively. Daily tree transpiration ranged from 3.64 to 4.35 Ld. To reduce air temperature by 1°C in the studied area, 63 large would be required per hectare, whereas to reduce the air temperature by 2°C only 24 large trees would be required. This study suggests increasing tree canopy cover in the city cannot mitigate UHI adequately but requires choosing the most appropriate tree species to solve this problem. It is imperative to include these types of studies in tree selection and urban development planning to adequately mitigate UHI. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Insectivorous bats respond to vegetation complexity in urban green spaces.

PubMed

Suarez-Rubio, Marcela; Ille, Christina; Bruckner, Alexander

2018-03-01

Structural complexity is known to determine habitat quality for insectivorous bats, but how bats respond to habitat complexity in highly modified areas such as urban green spaces has been little explored. Furthermore, it is uncertain whether a recently developed measure of structural complexity is as effective as field-based surveys when applied to urban environments. We assessed whether image-derived structural complexity (MIG) was as/more effective than field-based descriptors in this environment and evaluated the response of insectivorous bats to structural complexity in urban green spaces. Bat activity and species richness were assessed with ultrasonic devices at 180 locations within green spaces in Vienna, Austria. Vegetation complexity was assessed using 17 field-based descriptors and by calculating the mean information gain (MIG) using digital images. Total bat activity and species richness decreased with increasing structural complexity of canopy cover, suggesting maneuverability and echolocation (sensorial) challenges for bat species using the canopy for flight and foraging. The negative response of functional groups to increased complexity was stronger for open-space foragers than for edge-space foragers. Nyctalus noctula , a species foraging in open space, showed a negative response to structural complexity, whereas Pipistrellus pygmaeus , an edge-space forager, was positively influenced by the number of trees. Our results show that MIG is a useful, time- and cost-effective tool to measure habitat complexity that complemented field-based descriptors. Response of insectivorous bats to structural complexity was group- and species-specific, which highlights the need for manifold management strategies (e.g., increasing or reinstating the extent of ground vegetation cover) to fulfill different species' requirements and to conserve insectivorous bats in urban green spaces.

Integrating a street-canyon model with a regional Gaussian dispersion model for improved characterisation of near-road air pollution

NASA Astrophysics Data System (ADS)

Fallah-Shorshani, Masoud; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2017-03-01

The development and use of dispersion models that simulate traffic-related air pollution in urban areas has risen significantly in support of air pollution exposure research. In order to accurately estimate population exposure, it is important to generate concentration surfaces that take into account near-road concentrations as well as the transport of pollutants throughout an urban region. In this paper, an integrated modelling chain was developed to simulate ambient Nitrogen Dioxide (NO2) in a dense urban neighbourhood while taking into account traffic emissions, the regional background, and the transport of pollutants within the urban canopy. For this purpose, we developed a hybrid configuration including 1) a street canyon model, which simulates pollutant transfer along streets and intersections, taking into account the geometry of buildings and other obstacles, and 2) a Gaussian puff model, which resolves the transport of contaminants at the top of the urban canopy and accounts for regional meteorology. Each dispersion model was validated against measured concentrations and compared against the hybrid configuration. Our results demonstrate that the hybrid approach significantly improves the output of each model on its own. An underestimation appears clearly for the Gaussian model and street-canyon model compared to observed data. This is due to ignoring the building effect by the Gaussian model and undermining the contribution of other roads by the canyon model. The hybrid approach reduced the RMSE (of observed vs. predicted concentrations) by 16%-25% compared to each model on its own, and increased FAC2 (fraction of predictions within a factor of two of the observations) by 10%-34%.

Leaf reflectance variation along a vertical crown gradient of two deciduous tree species in a Belgian industrial habitat.

PubMed

Khavaninzadeh, Ali Reza; Veroustraete, Frank; Van Wittenberghe, Shari; Verrelst, Jochem; Samson, Roeland

2015-09-01

The reflectometry of leaf asymmetry is a novel approach in the bio-monitoring of tree health in urban or industrial habitats. Leaf asymmetry responds to the degree of environmental pollution and reflects structural changes in a leaf due to environmental pollution. This paper describes the boundary conditions to scale up from leaf to canopy level reflectance, by describing the variability of adaxial and abaxial leaf reflectance, hence leaf asymmetry, along the crown height gradients of two tree species. Our findings open a research pathway towards bio-monitoring based on the airborne remote sensing of tree canopies and their leaf asymmetric properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

Supplementary data of “Impacts of mesic and xeric urban vegetation on outdoor thermal comfort and microclimate in Phoenix, AZ”

PubMed Central

Song, Jiyun; Wang, Zhi-Hua

2015-01-01

An advanced Markov-Chain Monte Carlo approach called Subset Simulation is described in Au and Beck (2001) [1] was used to quantify parameter uncertainty and model sensitivity of the urban land-atmospheric framework, viz. the coupled urban canopy model-single column model (UCM-SCM). The results show that the atmospheric dynamics are sensitive to land surface conditions. The most sensitive parameters are dimensional parameters, i.e. roof width, aspect ratio, roughness length of heat and momentum, since these parameters control the magnitude of sensible heat flux. The relative insensitive parameters are hydrological parameters since the lawns or green roofs in urban areas are regularly irrigated so that the water availability for evaporation is never constrained. PMID:26702421

Information for forest process models: a review of NRS-FIA vegetation measurements

Treesearch

Charles D. Canham; William H. McWilliams

2012-01-01

The Forest and Analysis Program of the Northern Research Station (NRS-FIA) has re-designed Phase 3 measurements and intensified the sample intensity following a study to balance costs, utility, and sample size. The sampling scheme consists of estimating canopy-cover percent for six vegetation growth habits on 24-foot-radius subplots in four height classes and as an...

An analysis of urban thermal characteristics and associated land cover in Tampa Bay and Las Vegas using Landsat satellite data

USGS Publications Warehouse

Xian, George; Crane, Mike

2006-01-01

Remote sensing data from both Landsat 5 and Landsat 7 systems were utilized to assess urban area thermal characteristics in Tampa Bay watershed of west-central Florida, and the Las Vegas valley of southern Nevada. To quantitatively determine urban land use extents and development densities, sub-pixel impervious surface areas were mapped for both areas. The urban–rural boundaries and urban development densities were defined by selecting certain imperviousness threshold values and Landsat thermal bands were used to investigate urban surface thermal patterns. Analysis results suggest that urban surface thermal characteristics and patterns can be identified through qualitatively based urban land use and development density data. Results show the urban area of the Tampa Bay watershed has a daytime heating effect (heat-source), whereas the urban surface in Las Vegas has a daytime cooling effect (heat-sink). These thermal effects strongly correlated with urban development densities where higher percent imperviousness is usually associated with higher surface temperature. Using vegetation canopy coverage information, the spatial and temporal distributions of urban impervious surface and associated thermal characteristics are demonstrated to be very useful sources in quantifying urban land use, development intensity, and urban thermal patterns.

Quantifying dominance of intra-storm phase of interception process by small isolated canopies

NASA Astrophysics Data System (ADS)

Yerk, Walter; Montalto, Franco

2014-05-01

Precipitation interception by vegetation canopies has long been recognized as a major component of the hydrologic cycle; however, historically most research has been dedicated to closed or sparse canopy forests. The goal of our research was to quantify rainfall partitioning by small isolated canopies in an urban setting. The field experiment involved small forms of four shrub species (Prunus laurocerasus, Cornus sericea, Itea virginica and Hydrangea quercifolia) with crown heights 40 - 80 cm and diameters 35 - 60 cm. Each plant had ten rain gauges to measure throughfall with a sampling frequency of 5 seconds. An on-site automated weather station provided meteorological data. Leaf area index (LAI) was measured by manual counting. We estimated the canopy storage capacities of all four species to be less than 0.5 mm. The obtained data showed statistically significant differences in interception properties among all four species, except between Cornus and Itea. Cumulative interception loss for the period of August-December 2013 was 10% for Cornus, 16% for Itea, 29% for Hydrangea, and 49% for Prunus. The observations revealed a weak relationship between interception abilities and LAI for all four species. Throughfall and precipitation intensities (mm/hr) expressed very strong linear relationship (adjusted coefficients of determination were from 0.80 to 0.95) for the entire range of observed rainfall intensities. For Cornus the ratio of throughfall to precipitation intensity was close to 0.93:1, for Itea it was 0.82:1. The ratios were lesser for Hydrangea (0.65:1), and especially for Prunus (0.48:1). Therefore we show that reduced by the canopy, throughfall intensity results in the bulk of precipitation depth intercepted during the rain events. In contrast, the amount of water stored on the canopy and evaporated between and after rain events contributes minimally to interception. Simulations of potential evaporation based on the Penman-Monteith method showed a large underestimation of evaporation from the wet canopies during the rain events. Approaches other than energy balance models of potential evaporation from a still water surface are being discussed in order to explain large evaporation from within a wet isolated canopy.

Mapping forest canopy fuels in Yellowstone National Park using lidar and hyperspectral data

NASA Astrophysics Data System (ADS)

Halligan, Kerry Quinn

The severity and size of wildland fires in the forested western U.S have increased in recent years despite improvements in fire suppression efficiency. This, along with increased density of homes in the wildland-urban interface, has resulted in high costs for fire management and increased risks to human health, safety and property. Crown fires, in comparison to surface fires, pose an especially high risk due to their intensity and high rate of spread. Crown fire models require a range of quantitative fuel parameters which can be difficult and costly to obtain, but advances in lidar and hyperspectral sensor technologies hold promise for delivering these inputs. Further research is needed, however, to assess the strengths and limitations of these technologies and the most appropriate analysis methodologies for estimating crown fuel parameters from these data. This dissertation focuses on retrieving critical crown fuel parameters, including canopy height, canopy bulk density and proportion of dead canopy fuel, from airborne lidar and hyperspectral data. Remote sensing data were used in conjunction with detailed field data on forest parameters and surface reflectance measurements. A new method was developed for retrieving Digital Surface Model (DSM) and Digital Canopy Models (DCM) from first return lidar data. Validation data on individual tree heights demonstrated the high accuracy (r2 0.95) of the DCMs developed via this new algorithm. Lidar-derived DCMs were used to estimate critical crown fire parameters including available canopy fuel, canopy height and canopy bulk density with linear regression model r2 values ranging from 0.75 to 0.85. Hyperspectral data were used in conjunction with Spectral Mixture Analysis (SMA) to assess fuel quality in the form of live versus dead canopy proportions. Severity and stage of insect-caused forest mortality were estimated using the fractional abundance of green vegetation, non-photosynthetic vegetation and shade obtained from SMA. Proportion of insect attack was estimated with a linear model producing an r2 of 0.6 using SMA and bark endmembers from image and reference libraries. Fraction of red attack, with a possible link to increased crown fire risk, was estimated with an r2 of 0.45.

Designing a Multi-Objective Multi-Support Accuracy Assessment of the 2001 National Land Cover Data (NLCD 2001) of the Conterminous United States

EPA Science Inventory

The database design and diverse application of NLCD 2001 pose significant challenges for accuracy assessment because numerous objectives are of interest, including accuracy of land cover, percent urban imperviousness, percent tree canopy, land-cover composition, and net change. ...

Potential canopy interception of nitrogen in the Pacific Northwest, USA

Treesearch

Jeffrey M. Klopatek; Matthew J. Barry; Dale W. Johnson

2006-01-01

Nitrogen deposition is increasing worldwide from anthropogenic sources and encroactring upon previously N limited ecosystems. Recent literature reports increases in inorganic N deposition in Pacific Northwest forests of the United States due to expanding urbanization. We examined the contributions of atmospheric deposition of inorganic N to old-growth and second-growth...

Brooklyn's urban forest

Treesearch

David J. Nowak; Daniel E. Crane; Jack C. Stevens; Myriam Ibarra

2002-01-01

An assessment of trees in Brooklyn, New York, reveal that this borough has approximately 610,000 trees with canopies that cover 11.4 percent of the area. The most common trees are estimated to be tree of heaven, white mulberry, black locust, Norway maple and black cherry. Brooklyn's trees currently store approximately 172,000 metric tons of carbon with an...

Trees grow on money: urban tree canopy cover and environmental justice.

PubMed

Schwarz, Kirsten; Fragkias, Michail; Boone, Christopher G; Zhou, Weiqi; McHale, Melissa; Grove, J Morgan; O'Neil-Dunne, Jarlath; McFadden, Joseph P; Buckley, Geoffrey L; Childers, Dan; Ogden, Laura; Pincetl, Stephanie; Pataki, Diane; Whitmer, Ali; Cadenasso, Mary L

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman's correlation, ordinary least squares regression (OLS), and a spatial autoregressive model (SAR). Across all cities there is a strong positive correlation between UTC cover and median household income. Negative correlations between race and UTC cover exist in bivariate models for some cities, but they are generally not observed using multivariate regressions that include additional variables on income, education, and housing age. SAR models result in higher r-square values compared to the OLS models across all cities, suggesting that spatial autocorrelation is an important feature of our data. Similarities among cities can be found based on shared characteristics of climate, race/ethnicity, and size. Our findings suggest that a suite of variables, including income, contribute to the distribution of UTC cover. These findings can help target simultaneous strategies for UTC goals and environmental justice concerns.

Boreal forest BVOC exchange: emissions versus in-canopy sinks

NASA Astrophysics Data System (ADS)

Zhou, Putian; Ganzeveld, Laurens; Taipale, Ditte; Rannik, Üllar; Rantala, Pekka; Petteri Rissanen, Matti; Chen, Dean; Boy, Michael

2017-12-01

A multilayer gas dry deposition model has been developed and implemented into a one-dimensional chemical transport model SOSAA (model to Simulate the concentrations of Organic vapours, Sulphuric Acid and Aerosols) to calculate the dry deposition velocities for all the gas species included in the chemistry scheme. The new model was used to analyse in-canopy sources and sinks, including gas emissions, chemical production and loss, dry deposition, and turbulent transport of 12 featured biogenic volatile organic compounds (BVOCs) or groups of BVOCs (e.g. monoterpenes, isoprene+2-methyl-3-buten-2-ol (MBO), sesquiterpenes, and oxidation products of mono- and sesquiterpenes) in July 2010 at the boreal forest site SMEAR II (Station for Measuring Ecosystem-Atmosphere Relations). According to the significance of modelled monthly-averaged individual source and sink terms inside the canopy, the selected BVOCs were classified into five categories: 1. Most of emitted gases are transported out of the canopy (monoterpenes, isoprene + MBO). 2. Chemical reactions remove a significant portion of emitted gases (sesquiterpenes). 3. Bidirectional fluxes occur since both emission and dry deposition are crucial for the in-canopy concentration tendency (acetaldehyde, methanol, acetone, formaldehyde). 4. Gases removed by deposition inside the canopy are compensated for by the gases transported from above the canopy (acetol, pinic acid, β-caryophyllene's oxidation product BCSOZOH). 5. The chemical production is comparable to the sink by deposition (isoprene's oxidation products ISOP34OOH and ISOP34NO3). Most of the simulated sources and sinks were located above about 0.2 hc (canopy height) for oxidation products and above about 0.4 hc for emitted species except formaldehyde. In addition, soil deposition (including deposition onto understorey vegetation) contributed 11-61 % to the overall in-canopy deposition. The emission sources peaked at about 0.8-0.9 hc, which was higher than 0.6 hc where the maximum of dry deposition onto overstorey vegetation was located. This study provided a method to enable the quantification of the exchange between atmosphere and biosphere for numerous BVOCs, which could be applied in large-scale models in future. With this more explicit canopy exchange modelling system, this study analysed both the temporal and spatial variations in individual in-canopy sources and sinks, as well as their combined effects on driving BVOC exchange. In this study 12 featured BVOCs or BVOC groups were analysed. Other compounds could also be investigated similarly by being classified into these five categories.

Water-Channel Estimation of Eulerian and Lagrangian Time Scales of the Turbulence in Idealized Two-Dimensional Urban Canopies

NASA Astrophysics Data System (ADS)

Di Bernardino, Annalisa; Monti, Paolo; Leuzzi, Giovanni; Querzoli, Giorgio

2017-11-01

Lagrangian and Eulerian statistics are obtained from a water-channel experiment of an idealized two-dimensional urban canopy flow in neutral conditions. The objective is to quantify the Eulerian (TE) and Lagrangian (TL) time scales of the turbulence above the canopy layer as well as to investigate their dependence on the aspect ratio of the canopy, AR, as the latter is the ratio of the width ( W) to the height ( H) of the canyon. Experiments are also conducted for the case of flat terrain, which can be thought of as equivalent to a classical one-directional shear flow. The values found for the Eulerian time scales on flat terrain are in agreement with previous numerical results found in the literature. It is found that both the streamwise and vertical components of the Lagrangian time scale, T_u^L and T_w^L , follow Raupach's linear law within the constant-flux layer. The same holds true for T_w^L in both the canopies analyzed (AR= 1 and AR= 2) and also for T_u^L when AR = 1. In contrast, for AR = 2, T_u^L follows Raupach's law only above z=2H. Below that level, T_u^L is nearly constant with height, showing at z=H a value approximately one order of magnitude greater than that found for AR = 1. It is shown that the assumption usually adopted for flat terrain, that β =TL/TE is proportional to the inverse of the turbulence intensity, also holds true even for the canopy flow in the constant-flux layer. In particular, γ /i_u fits well β _u =T_u^L /T_u^E in both the configurations by choosing γ to be 0.35 (here, i_u =σ _u / \\bar{u} , where \\bar{u} and σ _u are the mean and the root-mean-square of the streamwise velocity component, respectively). On the other hand, β _w =T_w^L /T_w^E follows approximately γ /i_w =0.65/( {σ _w /\\bar{u} } ) for z > 2H, irrespective of the AR value. The second main objective is to estimate other parameters of interest in dispersion studies, such as the eddy diffusivity of momentum (KT) and the Kolmogorov constant (C_0). It is found that C_0 depends appreciably on the velocity component both for the flat terrain and canopy flow, even though for the latter case it is insensitive to AR values. In all the three experimental configurations analyzed here, KT shows an overall linear growth with height in agreement with the linear trend predicted by Prandtl's theory.

PALM-USM v1.0: A new urban surface model integrated into the PALM large-eddy simulation model

NASA Astrophysics Data System (ADS)

Resler, Jaroslav; Krč, Pavel; Belda, Michal; Juruš, Pavel; Benešová, Nina; Lopata, Jan; Vlček, Ondřej; Damašková, Daša; Eben, Kryštof; Derbek, Přemysl; Maronga, Björn; Kanani-Sühring, Farah

2017-10-01

Urban areas are an important part of the climate system and many aspects of urban climate have direct effects on human health and living conditions. This implies that reliable tools for local urban climate studies supporting sustainable urban planning are needed. However, a realistic implementation of urban canopy processes still poses a serious challenge for weather and climate modelling for the current generation of numerical models. To address this demand, a new urban surface model (USM), describing the surface energy processes for urban environments, was developed and integrated as a module into the PALM large-eddy simulation model. The development of the presented first version of the USM originated from modelling the urban heat island during summer heat wave episodes and thus implements primarily processes important in such conditions. The USM contains a multi-reflection radiation model for shortwave and longwave radiation with an integrated model of absorption of radiation by resolved plant canopy (i.e. trees, shrubs). Furthermore, it consists of an energy balance solver for horizontal and vertical impervious surfaces, and thermal diffusion in ground, wall, and roof materials, and it includes a simple model for the consideration of anthropogenic heat sources. The USM was parallelized using the standard Message Passing Interface and performance testing demonstrates that the computational costs of the USM are reasonable on typical clusters for the tested configurations. The module was fully integrated into PALM and is available via its online repository under the GNU General Public License (GPL). The USM was tested on a summer heat-wave episode for a selected Prague crossroads. The general representation of the urban boundary layer and patterns of surface temperatures of various surface types (walls, pavement) are in good agreement with in situ observations made in Prague. Additional simulations were performed in order to assess the sensitivity of the results to uncertainties in the material parameters, the domain size, and the general effect of the USM itself. The first version of the USM is limited to the processes most relevant to the study of summer heat waves and serves as a basis for ongoing development which will address additional processes of the urban environment and lead to improvements to extend the utilization of the USM to other environments and conditions.

[Estimation and Visualization of Nitrogen Content in Citrus Canopy Based on Two Band Vegetation Index (TBVI)].

PubMed

Wang, Qiao-nan; Ye, Xu-jun; Li, Jin-meng; Xiao, Yu-zhao; He, Yong

2015-03-01

Nitrogen is a necessary and important element for the growth and development of fruit orchards. Timely, accurate and nondestructive monitoring of nitrogen status in fruit orchards would help maintain the fruit quality and efficient production of the orchard, and mitigate the pollution of water resources caused by excessive nitrogen fertilization. This study investigated the capability of hyperspectral imagery for estimating and visualizing the nitrogen content in citrus canopy. Hyperspectral images were obtained for leaf samples in laboratory as well as for the whole canopy in the field with ImSpector V10E (Spectral Imaging Ltd., Oulu, Finland). The spectral datas for each leaf sample were represented by the average spectral data extracted from the selected region of interest (ROI) in the hyperspectral images with the aid of ENVI software. The nitrogen content in each leaf sample was measured by the Dumas combustion method with the rapid N cube (Elementar Analytical, Germany). Simple correlation analysis and the two band vegetation index (TBVI) were then used to develop the spectra data-based nitrogen content prediction models. Results obtained through the formula calculation indicated that the model with the two band vegetation index (TBVI) based on the wavelengths 811 and 856 nm achieved the optimal estimation of nitrogen content in citrus leaves (R2 = 0.607 1). Furthermore, the canopy image for the identified TBVI was calculated, and the nitrogen content of the canopy was visualized by incorporating the model into the TBVI image. The tender leaves, middle-aged leaves and elder leaves showed distinct nitrogen status from highto low-levels in the canopy image. The results suggested the potential of hyperspectral imagery for the nondestructive detection and diagnosis of nitrogen status in citrus canopy in real time. Different from previous studies focused on nitrogen content prediction at leaf level, this study succeeded in predicting and visualizing the nutrient content of fruit trees at canopy level. This would provide valuable information for the implementation of individual tree-based fertilization schemes in precision orchard management practices.

FluorMODgui V3.0: A graphic user interface for the spectral simulation of leaf and canopy chlorophyll fluorescence

NASA Astrophysics Data System (ADS)

Zarco-Tejada, P. J.; Miller, J. R.; Pedrós, R.; Verhoef, W.; Berger, M.

2006-06-01

The FluorMODgui Graphic User Interface (GUI) software package developed within the frame of the FluorMOD project Development of a Vegetation Fluorescence Canopy Model is presented in this manuscript. The FluorMOD project was launched in 2002 by the European Space Agency (ESA) to advance the science of vegetation fluorescence simulation through the development and integration of leaf and canopy fluorescence models based on physical methods. The design of airborne or space missions dedicated to the measurement of solar-induced chlorophyll fluorescence using remote-sensing instruments require physical methods for quantitative feasibility analysis and sensor specification studies. The FluorMODgui model developed as part of this project is designed to simulate the effects of chlorophyll fluorescence at leaf and canopy levels using atmospheric inputs, running the leaf model, FluorMODleaf, and the canopy model, FluorSAIL, independently, through a coupling scheme, and by a multiple iteration protocol to simulate changes in the viewing geometry and atmospheric characteristics. Inputs for the FluorMODleaf model are the number of leaf layers, chlorophyll a+ b content, water equivalent thickness, dry matter content, fluorescence quantum efficiency, temperature, species type, and stoichiometry. Inputs for the FluorSAIL canopy model are a MODTRAN-4 6-parameter spectra or measured direct horizontal irradiance and diffuse irradiance spectra, a soil reflectance spectrum, leaf reflectance & transmittance spectra and a excitation-fluorescence response matrix in upward and downward directions (all from FluorMODleaf), 2 PAR-dependent coefficients for the fluorescence response to light level, relative azimuth angle and viewing zenith angle, canopy leaf area index, leaf inclination distribution function, and a hot spot parameter. Outputs available in the 400-1000 nm spectral range from the graphical user interface, FluorMODgui, are the leaf spectral reflectance and transmittance, and the canopy reflectance, with and without fluorescence effects. In addition, solar and sky irradiance on the ground, radiance with and without fluorescence on the ground, and top-of-atmosphere (TOA) radiances for bare soil and surroundings same as target are also produced. The models and documentation regarding the FluorMOD project can be downloaded at http://www.ias.csic.es/fluormod.

Downscaling modelling system for multi-scale air quality forecasting

NASA Astrophysics Data System (ADS)

Nuterman, R.; Baklanov, A.; Mahura, A.; Amstrup, B.; Weismann, J.

2010-09-01

Urban modelling for real meteorological situations, in general, considers only a small part of the urban area in a micro-meteorological model, and urban heterogeneities outside a modelling domain affect micro-scale processes. Therefore, it is important to build a chain of models of different scales with nesting of higher resolution models into larger scale lower resolution models. Usually, the up-scaled city- or meso-scale models consider parameterisations of urban effects or statistical descriptions of the urban morphology, whereas the micro-scale (street canyon) models are obstacle-resolved and they consider a detailed geometry of the buildings and the urban canopy. The developed system consists of the meso-, urban- and street-scale models. First, it is the Numerical Weather Prediction (HIgh Resolution Limited Area Model) model combined with Atmospheric Chemistry Transport (the Comprehensive Air quality Model with extensions) model. Several levels of urban parameterisation are considered. They are chosen depending on selected scales and resolutions. For regional scale, the urban parameterisation is based on the roughness and flux corrections approach; for urban scale - building effects parameterisation. Modern methods of computational fluid dynamics allow solving environmental problems connected with atmospheric transport of pollutants within urban canopy in a presence of penetrable (vegetation) and impenetrable (buildings) obstacles. For local- and micro-scales nesting the Micro-scale Model for Urban Environment is applied. This is a comprehensive obstacle-resolved urban wind-flow and dispersion model based on the Reynolds averaged Navier-Stokes approach and several turbulent closures, i.e. k -ɛ linear eddy-viscosity model, k - ɛ non-linear eddy-viscosity model and Reynolds stress model. Boundary and initial conditions for the micro-scale model are used from the up-scaled models with corresponding interpolation conserving the mass. For the boundaries a kind of Dirichlet condition is chosen to provide the values based on interpolation from the coarse to the fine grid. When the roughness approach is changed to the obstacle-resolved one in the nested model, the interpolation procedure will increase the computational time (due to additional iterations) for meteorological/ chemical fields inside the urban sub-layer. In such situations, as a possible alternative, the perturbation approach can be applied. Here, the effects of main meteorological variables and chemical species are considered as a sum of two components: background (large-scale) values, described by the coarse-resolution model, and perturbations (micro-scale) features, obtained from the nested fine resolution model.

Carbon dioxide fluxes dynamics comparison in Moscow urban forest and adjacent urban areas

NASA Astrophysics Data System (ADS)

Yaroslavtsev, Alexis; Meshalkina, Joulia; Mazirov, Ilya; Vasenev, Ivan

2017-04-01

In the beginning of the 2014 in northern district of Moscow was installed eddy covariance tower on the edge of Timiryazevskiy urban forest and Timiryazevskiy district of Moscow. Tower 34m high was constructed inside the territory of LOD (Lesnaya Opytnaya Dacha) experimental station in the south-eastern part of the forest. Main tree species of urban forest and neighboring urban areas are Acer Plantanoides, Tilia cordata, Betula pendula, Quercus robur, Pinus sylvestris. Forest itself is mixed with some small plots dominated only by deciduous or coniferous species, whether trees in urban areas was mainly deciduous. Mean canopy height is about 30m. in both forest and urban areas. The soil cover of the studied sections is represented by sod-podzolic soils with different degree of development of the humus horizon. All soils have well-developed profile of sod-podzolic soil with low power litter (only in forest area) and developed humus-accumulative horizon with high humus content (3,24%) Carbon dioxide daily fluxes from investigated area was calculated for six months of 2014 (from April till October) utilizing eddy covariance method. Most (90%) of fluxes footprints was no longer than 500m for all wind directions during the time of monitoring. Forest in 500m radius around tower is a zone of active recreation with several roads and wide path network. On the other hand closest to tower urban area characterized by a low-rise buildings (in most cases no more than 5 floors) which are mainly administration ones and have wide green areas around them very few roads and low traffic. As a result difference in calculated fluxes was not so dramatic, as it was expected. Diurnal carbon dioxide fluxes dynamics was pretty the same for all months except August, due to long period without precipitation and higher soil moisture under the forest canopy. Estimated daily fluxes values was higher in forest areas for the whole period of investigation, except August, and ranged from -2 to 8 g C CO2 d-1 m-2 with mean about 2,5 g C CO2 d-1 m-2 .

The impact of in-canopy wind profile formulations on heat flux estimation in an open orchard using the remote sensing-based two-source model

NASA Astrophysics Data System (ADS)

Cammalleri, C.; Anderson, M. C.; Ciraolo, G.; Durso, G.; Kustas, W. P.; La Loggia, G.; Minacapilli, M.

2010-12-01

For open orchard and vineyard canopies containing significant fractions of exposed soil (>50%), typical of Mediterranean agricultural regions, the energy balance of the vegetation elements is strongly influenced by heat exchange with the bare soil/substrate. For these agricultural systems a "two-source" approach, where radiation and turbulent exchange between the soil and canopy elements are explicitly modelled, appears to be the only suitable methodology for reliably assessing energy fluxes. In strongly clumped canopies, the effective wind speed profile inside and below the canopy layer can strongly influence the partitioning of energy fluxes between the soil and vegetation components. To assess the impact of in-canopy wind profile on model flux estimates, an analysis of three different formulations is presented, including algorithms from Goudriaan (1977), Massman (1987) and Lalic et al. (2003). The in-canopy wind profile formulations are applied to the thermal-based two-source energy balance (TSEB) model developed by Norman et al. (1995) and modified by Kustas and Norman (1999). High resolution airborne remote sensing images, collected over an agricultural area located in the western part of Sicily (Italy) comprised primarily of vineyards, olive and citrus orchards, are used to derive all the input parameters needed to apply the TSEB. The images were acquired from June to October 2008 and include a relatively wide range of meteorological and soil moisture conditions. A preliminary sensitivity analysis of the three wind profile algorithms highlights the dependence of wind speed just above the soil/substrate to leaf area index and canopy height over the typical range of canopy properties encountered in these agricultural areas. It is found that differences among the models in wind just above the soil surface are most significant under sparse and medium fractional cover conditions (15-50%). The TSEB model heat flux estimates are compared with micro-meteorological measurements from a small aperture scintillometer and an eddy covariance tower collected over an olive orchard characterized by moderate fractional vegetation cover (≍35%) and relatively tall crop (≍3.5 m). TSEB fluxes for the 7 image acquisition dates generated using both the Massman and Goudriaan in-canopy wind profile formulations give close agreement with measured fluxes, while the Lalic et al. equations yield poor results. The Massman wind profile scheme slightly outperforms that of Goudriaan, but it requires an additional parameter accounting for the roughness sub-layer of the underlying vegetative surface. The analysis also suggests that within-canopy wind profile model discrepancies become important, in terms of impact on modelled sensible heat flux, only for sparse canopies with moderate vegetation coverage.

The impact of in-canopy wind profile formulations on heat flux estimation using the remote sensing-based two-source model for an open orchard canopy in southern Italy

NASA Astrophysics Data System (ADS)

Cammalleri, C.; Anderson, M. C.; Ciraolo, G.; D'Urso, G.; Kustas, W. P.; La Loggia, G.; Minacapilli, M.

2010-07-01

For open orchard and vineyard canopies containing significant fractions of exposed soil (>50%), typical of Mediterranean agricultural regions, the energy balance of the vegetation elements is strongly influenced by heat exchange with the bare soil/substrate. For these agricultural systems a "two-source" approach, where radiation and turbulent exchange between the soil and canopy elements are explicitly modelled, appears to be the only suitable methodology for reliably assessing energy fluxes. In strongly clumped canopies, the effective wind speed profile inside and below the canopy layer can highly influence the partitioning of energy fluxes between the soil and vegetation components. To assess the impact of in-canopy wind profile on model flux estimates, an analysis of three different formulations is presented, including algorithms from Goudriaan (1977), Massman (1987) and Lalic et al. (2003). The in-canopy wind profile formulations are applied to the thermal-based Two-Source Energy Balance (TSEB) model developed by Norman et al. (1995) and modified by Kustas and Norman (1999). High resolution airborne remote sensing images, collected over an agricultural area located in the western part of Sicily (Italy) comprised primarily of vineyards, olive and citrus orchards, are used to derive all the input parameters need to apply the TSEB. The images were acquired from June to October 2008 and include a relatively wide range of meteorological and soil moisture conditions. A preliminary sensitivity analysis of the three wind profile algorithms highlight the dependence of wind speed just above the soil/substrate to leaf area index and canopy height over the typical canopy properties range of these agricultural area. It is found that differences in wind just above surface among the models is most significant under sparse and medium fractional cover conditions (20-60%). The TSEB model heat flux estimates are compared with micrometeorological measurements from a small aperture scintillometer and an eddy covariance tower collected over an olive orchard characterized by moderate fractional vegetation cover (≈35%) and relatively tall crop height (≈3.5 m). TSEB fluxes for the 7 image acquisition dates generated using both the Massman and Goudriaan in-canopy wind profile formulations give close agreement with measured fluxes, while the Lalic et al. equations yield poor results. The Massman wind profile scheme slightly outperforms that of Goudriaan, but it requires an additional parameter describing the roughness of the underlying vegetative surface. This parameter is not directly obtainable using remote sensing, hence this study suggests that the Goudriaan formulation for landscape applications is most suitable when detailed site-specific information regarding canopy architecture is unavailable.

Estimating urban trees and carbon stock potentials for mitigating climate change in Lagos: Case of Ikeja Government Reserved Area (GRA)

NASA Astrophysics Data System (ADS)

Elias, P. O.; Faderin, A.

2014-12-01

Urban trees are a component of the urban infrastructure which offers diverse services including environmental, aesthetic and economic. The accumulation of carbon in the atmosphere resulting from the indiscriminate distribution of human populations and urban activities with the unsustainable consumption of natural resources contributes to global environmental change especially in coastal cities like Lagos. Carbon stocks and sequestration by urban trees are increasingly recognized to play significant roles for mitigating climate change. This paper focuses on the estimation of carbon stock and sequestration through biomass estimation and quantification in Ikeja GRA, Lagos. Ikeja possesses a characteristic feature as a microcosm of Lagos due to the wide range of land uses. A canopy assessment of tree population was carried out using itree canopy software. A GPS survey was used to collect an inventory of all trees showing their location, spatial distribution and other attributes. The analysis of the carbon storage and sequestration potential of both actual and potential tree planting sites involved biomass estimations from tree allometry equations. Trees were identified at species level and measurements of their dendrometric values were recorded and integrated into the GIS database to estimate biomass of trees and carbon storage. The trees in the study area were estimated to have a biomass of 441.9 mg and carbon storage of 221.395 kg/tree. By considering the potential tree planting sites the estimated carbon stored increased to 11,352.73 kg. Carbon sequestration value in the study area was found to be 1.6790 tonnes for the existing trees and 40.707 tonnes for the potential tree planting sites (PTPS). The estimation of carbon storage and sequestration values of trees are important incentives for carbon accounting/footprints and monitoring of climate change mitigation which has implications for evaluation and monitoring of urban ecosystem.

An Improved Simulation of the Diurnally Varying Street Canyon Flow

NASA Astrophysics Data System (ADS)

Yaghoobian, Neda; Kleissl, Jan; Paw U, Kyaw Tha

2012-11-01

The impact of diurnal variation of temperature distribution over building and ground surfaces on the wind flow and scalar transport in street canyons is numerically investigated using the PArallelized LES Model (PALM). The Temperature of Urban Facets Indoor-Outdoor Building Energy Simulator (TUF-IOBES) is used for predicting urban surface heat fluxes as boundary conditions for a modified version of PALM. TUF-IOBES dynamically simulates indoor and outdoor building surface temperatures and heat fluxes in an urban area taking into account weather conditions, indoor heat sources, building and urban material properties, composition of the building envelope (e.g. windows, insulation), and HVAC equipment. Temperature (and heat flux) distribution over urban surfaces of the 3-D raster-type geometry of TUF-IOBES makes it possible to provide realistic, high resolution boundary conditions for the numerical simulation of flow and scalar transport in an urban canopy. Compared to some previous analyses using uniformly distributed thermal forcing associated with urban surfaces, the present analysis shows that resolving non-uniform thermal forcings can provide more detailed and realistic patterns of the local air flow and pollutant dispersion in urban canyons.

Social health insurance coverage and financial protection among rural-to-urban internal migrants in China: evidence from a nationally representative cross-sectional study

PubMed Central

Chen, Wen; Zhang, Qi; Renzaho, Andre M N; Zhou, Fangjing; Zhang, Hui; Ling, Li

2017-01-01

Introduction Migrants are a vulnerable population and could experience various challenges and barriers to accessing health insurance. Health insurance coverage protects migrants from financial loss related to illness and death. We assessed social health insurance (SHI) coverage and its financial protection effect among rural-to-urban internal migrants (IMs) in China. Methods Data from the ‘2014 National Internal Migrant Dynamic Monitoring Survey’ were used. We categorised 170 904 rural-to-urban IMs according to their SHI status, namely uninsured by SHI, insured by the rural SHI scheme (new rural cooperative medical scheme (NCMS)) or the urban SHI schemes (urban employee-based basic medical insurance (UEBMI)/urban resident-based basic medical insurance (URBMI)), and doubly insured (enrolled in both rural and urban schemes). Financial protection was defined as ‘the percentage of out-of-pocket (OOP) payments for the latest inpatient service during the past 12 months in the total household expenditure’. Results The uninsured rate of SHI and the NCMS, UEBMI/URBMI and double insurance coverage in rural-to-urban IMs was 17.3% (95% CI 16.9% to 17.7%), 66.6% (66.0% to 67.1%), 22.6% (22.2% to 23.0%) and 5.5% (5.3% to 5.7%), respectively. On average, financial protection indicator among uninsured, only NCMS insured, only URBMI/UEBMI insured and doubly insured participants was 13.3%, 9.2%, 6.2% and 5.8%, respectively (p=0.004). After controlling for confounding factors and adjusting the protection effect of private health insurance, compared with no SHI, the UEBMI/URBMI, the NCMS and double insurance could reduce the average percentage share of OOP payments by 33.9% (95% CI 25.5% to 41.4%), 14.1% (6.6% to 20.9%) and 26.8% (11.0% to 39.7%), respectively. Conclusion Although rural-to-urban IMs face barriers to accessing SHI schemes, our findings confirm the positive financial protection effect of SHI. Improving availability and portability of health insurance would promote financial protection for IMs, and further facilitate achieving universal health coverage in China and other countries that face migration-related obstacles to achieve universal coverage. PMID:29082027

Wintertime ozone fluxes and profiles above a subalpine spruce-fir forest

Treesearch

Karl Zeller

2000-01-01

High rural concentrations of ozone (O3) are thought to be stratospheric in origin, advected from upwind urban sources, or photochemically generated locally by natural trace gas emissions. Ozone is known to be transported vertically downward from the above-canopy atmospheric surface layer and destroyed within stomata or on other biological and mineral surfaces. However...

Potential energy savings in buildings by an urban tree planting programme in California

Treesearch

E.G. McPherson; J.R. Simpson

2003-01-01

Tree canopy cover data from aerial photographs and building energy simulations were applied to estimate energy savings from existing trees and new plantings in California. There are approximately 177.3 million energy-conserving trees in California communities and 241.6 million empty planting sites. Existing trees are projected to reduce annual air conditioning energy...

Canopy decline assessment in American elm after inoculation with different doses of Ophiostoma ulmi and O. novo-ulmi

Treesearch

Charles E. Flower; James M. Slavicek; Dale Lesser; Steven Eshita; Cornelia C. Pinchot

2017-01-01

Restoration of American elm (Ulmus americana L.) in natural and urban landscapes necessitates the development of new selections that not only exhibit Dutch elm disease (DED, caused by the fungal pathogen Ophiostoma novo-ulmi and O. ulmi) tolerance, but also an increase the genetic variability of tolerant...

Diurnal changes in urban boundary layer environment induced by urban greening

NASA Astrophysics Data System (ADS)

Song, Jiyun; Wang, Zhi-Hua

2016-11-01

Urban green infrastructure has been widely used for mitigating adverse environmental problems as well as enhancing urban sustainability of cities worldwide. Here we develop an integrated urban-land-atmosphere modeling framework with the land surface processes parameterized by an advanced urban canopy model and the atmospheric processes parameterized by a single column model. The model is then applied to simulate a variety of forms of green infrastructure, including urban lawns, shade trees, green and cool roofs, and their impact on environmental changes in the total urban boundary layer (UBL) for a stereotypical desert city, viz. Phoenix, Arizona. It was found that green roofs have a relatively uniform cooling effect proportional to their areal coverage. In particular, a reduction of UBL temperature of 0.3 °C and 0.2 °C per 10% increase of green roof coverage was observed at daytime and nighttime, respectively. In contrast, the effect of greening of street canyons is constrained by the overall abundance of green infrastructure and the energy available for evapotranspiration. In addition, the increase in urban greening causes boundary-layer height to decrease during daytime but increase at nighttime, leading to different trends of changes in urban air quality throughout a diurnal cycle.

Nowhere safe? Exploring the influence of urbanization across mainland and insular seashores in continental Portugal and the Azorean Archipelago.

PubMed

Bertocci, Iacopo; Arenas, Francisco; Cacabelos, Eva; Martins, Gustavo M; Seabra, Maria I; Álvaro, Nuno V; Fernandes, Joana N; Gaião, Raquel; Mamede, Nuno; Mulas, Martina; Neto, Ana I

2017-01-30

Differences in the structure and functioning of intensively urbanized vs. less human-affected systems are reported, but such evidence is available for a much larger extent in terrestrial than in marine systems. We examined the hypotheses that (i) urbanization was associated to different patterns of variation of intertidal assemblages between urban and extra-urban environments; (ii) such patterns were consistent across mainland and insular systems, spatial scales from 10scm to 100skm, and a three months period. Several trends emerged: (i) a more homogeneous distribution of most algal groups in the urban compared to the extra-urban condition and the opposite pattern of most invertebrates; (ii) smaller/larger variances of most organisms where these were, respectively, less/more abundant; (iii) largest variability of most response variables at small scale; (iv) no facilitation of invasive species by urbanization and larger cover of canopy-forming algae in the insular extra-urban condition. Present findings confirm the acknowledged notion that future management strategies will require to include representative assemblages and their relevant scales of variation associated to urbanization gradients on both the mainland and the islands. Copyright © 2016 Elsevier Ltd. All rights reserved.

Incorporating maps of leaf chlorophyll in a thermal-based two-source energy balance scheme for mapping coupled fluxes of carbon and water exchange at a range of scales

NASA Astrophysics Data System (ADS)

Houborg, R.; Anderson, M. C.; Kustas, W. P.

2008-12-01

A light-use efficiency (LUE) based model of canopy resistance was recently implemented within a thermal- based Two-Source Energy Balance (TSEB) scheme facilitating coupled simulations of land-surface fluxes of water, energy and CO2 exchange from field to regional scales (Anderson et al., 2008). The LUE model component computes canopy-scale carbon assimilation and transpiration fluxes and incorporates LUE modifications from biome specific nominal values (Bn) in response to variations in humidity, CO2 concentration, temperature (soil and air), wind speed, and direct beam vs. diffuse light composition. Here we incorporate leaf chlorophyll content (Cab) as a determinant of spatial and temporal variations in Bn as Cab is related to key LUE modulating factors such as crop phenology, vegetation stress and photosynthetic capacity. A linear relationship between Bn and Cab, established from stand-level measurement of LUE for unstressed environmental conditions and a representative set of Cab values for a range of agricultural and natural vegetation groups, is used to distribute Bn over the modeling domain. The technique is tested for an agricultural area near Bushland, Texas by fusing reflective and thermal based remote sensing inputs from SPOT, Landsat, ASTER and aircraft sensor systems. Maps of LAI and Cab are generated by using at-sensor radiances in green, red and near-infrared wavelengths as input to a REGularized canopy reFLECtance (REGFLEC) modeling tool that couples leaf optics (PROSPECT), canopy reflectance (ACRM), and atmospheric radiative transfer (6SV1) model components. Modeled carbon and water fluxes are compared with eddy covariance measurements made in stands of cotton and with fluxes measured by an aircraft flying transects over irrigated and non-irrigated agricultural land and natural vegetation. The technique is flexible and scalable and is portable to continental scales using GOES and MODIS data products. The results demonstrate utility in combining remotely sensed observations in the reflective solar and thermal domains for estimating carbon and water fluxes within a coupled framework.

Implementation of an Online Chemistry Model to a Large Eddy Simulation Model (PALM-4U0

NASA Astrophysics Data System (ADS)

Mauder, M.; Khan, B.; Forkel, R.; Banzhaf, S.; Russo, E. E.; Sühring, M.; Kanani-Sühring, F.; Raasch, S.; Ketelsen, K.

2017-12-01

Large Eddy Simulation (LES) models permit to resolve relevant scales of turbulent motion, so that these models can capture the inherent unsteadiness of atmospheric turbulence. However, LES models are so far hardly applied for urban air quality studies, in particular chemical transformation of pollutants. In this context, BMBF (Bundesministerium für Bildung und Forschung) funded a joint project, MOSAIK (Modellbasierte Stadtplanung und Anwendung im Klimawandel / Model-based city planning and application in climate change) with the main goal to develop a new highly efficient urban climate model (UCM) that also includes atmospheric chemical processes. The state-of-the-art LES model PALM; Maronga et al, 2015, Geosci. Model Dev., 8, doi:10.5194/gmd-8-2515-2015), has been used as a core model for the new UCM named as PALM-4U. For the gas phase chemistry, a fully coupled 'online' chemistry model has been implemented into PALM. The latest version of the Kinetic PreProcessor (KPP) Version 2.3, has been utilized for the numerical integration of chemical species. Due to the high computational demands of the LES model, compromises in the description of chemical processes are required. Therefore, a reduced chemistry mechanism, which includes only major pollutants namely O3, NO, NO2, CO, a highly simplified VOC chemistry and a small number of products have been implemented. This work shows preliminary results of the advection, and chemical transformation of atmospheric pollutants. Non-cyclic boundaries have been used for inflow and outflow in east-west directions while periodic boundary conditions have been implemented to the south-north lateral boundaries. For practical applications, our approach is to go beyond the simulation of single street canyons to chemical transformation, advection and deposition of air pollutants in the larger urban canopy. Tests of chemistry schemes and initial studies of chemistry-turbulence, transport and transformations are presented.

Impacts of Realistic Urban Heating. Part II: Air Quality and City Breathability

NASA Astrophysics Data System (ADS)

Nazarian, Negin; Martilli, Alberto; Norford, Leslie; Kleissl, Jan

2018-03-01

Urban morphology and inter-building shadowing result in a non-uniform distribution of surface heating in urban areas, which can significantly modify the urban flow and thermal field. In Part I, we found that in an idealized three-dimensional urban array, the spatial distribution of the thermal field is correlated with the orientation of surface heating with respect to the wind direction (i.e. leeward or windward heating), while the dispersion field changes more strongly with the vertical temperature gradient in the street canyon. Here, we evaluate these results more closely and translate them into metrics of "city breathability," with large-eddy simulations coupled with an urban energy-balance model employed for this purpose. First, we quantify breathability by, (i) calculating the pollutant concentration at the pedestrian level (horizontal plane at z≈ 1.5 -2 m) and averaged over the canopy, and (ii) examining the air exchange rate at the horizontal and vertical ventilating faces of the canyon, such that the in-canopy pollutant advection is distinguished from the vertical removal of pollution. Next, we quantify the change in breathability metrics as a function of previously defined buoyancy parameters, horizontal and vertical Richardson numbers (Ri_h and Ri_v , respectively), which characterize realistic surface heating. We find that, unlike the analysis of airflow and thermal fields, consideration of the realistic heating distribution is not crucial in the analysis of city breathability, as the pollutant concentration is mainly correlated with the vertical temperature gradient (Ri_v ) as opposed to the horizontal (Ri_h ) or bulk (Ri_b ) thermal forcing. Additionally, we observe that, due to the formation of the primary vortex, the air exchange rate at the roof level (the horizontal ventilating faces of the building canyon) is dominated by the mean flow. Lastly, since Ri_h and Ri_v depend on the meteorological factors (ambient air temperature, wind speed, and wind direction) as well as urban design parameters (such as surface albedo), we propose a methodology for mapping overall outdoor ventilation and city breathability using this characterization method. This methodology helps identify the effects of design on urban microclimate, and ultimately informs urban designers and architects of the impact of their design on air quality, human health, and comfort.

Sources and Characterization of Submicron Aerosols in a Rural Forest During the PROPHET-AMOS 2016 Campaign

NASA Astrophysics Data System (ADS)

Bui, A. T.; Wallace, H. W., IV; Alvarez, S. L.; Erickson, M.; Alwe, H. D.; May, N.; Cook, R.; Connor, M.; Slade, J. H., Jr.; Shi, Q.; Kavassalis, S.; Tyndall, G. S.; Shepson, P. B.; Pratt, K.; Ault, A. P.; Millet, D. B.; Murphy, J. G.; Usenko, S.; Sheesley, R. J.; Flynn, J. H., III; Griffin, R. J.; Wang, W.

2017-12-01

Forests are a rich source of biogenic volatile organic compounds (BVOCs). Oxidation of BVOCs can result in the formation of secondary organic aerosol (SOA) and in the presence of NOx (NO+NO2) produce organic nitrate-containing particles. However, the distribution of both BVOCs and oxidants can be dramatically altered by the physical barriers provided by a forest canopy. Global models currently neglect the effect of these canopies on SOA formation in forested regions. In this work, we characterize non-refractory submicron aerosol (NR-PM1) using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) during the 2016 Program on Oxidants: Photochemistry, Emissions, and Transport-Atmospheric Measurements of Oxidants in Summer (PROPHET-AMOS) campaign. This site is located in a rural forest in northern Michigan and features a tower that allowed for both above and below canopy measurements. Our results indicate that organic aerosols (OA) account for a substantial portion of the NR-PM1 measured at this site. Organic nitrate aerosol can contribute up to 18% of the total OA and an average of 75% of the total measured nitrate aerosol. Episodes of above- and below-canopy NR-PM1 concentration differences indicate that above-canopy OA concentrations can be up to 40% greater than below-canopy, which represents an increase of up to 1.5 µg/m3. Organic fragment ions such as CxHy, CxHyOz, and CxHyO1 contribute to enhanced above-canopy OA concentrations. Positive matrix factorization analysis of the high-resolution OA mass spectra identified three SOA factors: low volatility oxygenated OA (LVOOA), isoprene-derived OOA (ISOOA), and oxygenated organic aerosol. Analysis of air mass backward trajectories and correlations with external data indicate that LVOOA correlates well with sulfate and aged, urban-influenced air masses, whereas ISOOA correlates well with isoprene SOA tracers and air masses originating from semi-remote areas. Our results indicate that the OA at this site is dominated by SOA formation and that vertical differences in OA can exist in the presence of a forest canopy. Results from this work have important implications in understanding the role that canopies play in SOA formation and provide useful data to help accurately validate biosphere-atmosphere exchange models.

The contribution of urbanization to recent extreme heat events and white roof mitigation strategy in the Beijing-Tianjin-Hebei metropolitan area

NASA Astrophysics Data System (ADS)

Wang, Mingna

2015-04-01

The UHI effect can aggravate summertime heat waves and strongly influence human comfort and health, leading to greater mortality in metropolitan areas. Many geo-engineering technological strategies have been proposed to mitigate climate warming, and for the UHI, increasing the albedo of artificial urban surfaces (rooftops or pavements) has been considered a lucrative and effective way to cool cities. The objective of this work is to quantify the contribution of urbanization to recent extreme heat events of the early 21st century in the Beijing-Tianjin-Hebei metropolitan area, using the mesoscale WRF model coupled with a single urban canopy model and actual urban land cover datasets. This work also investigates a simulation of the regional effects of white roof technology by increasing the albedo of urban areas in the urban canopy model to mitigate the urban heat island, especially in extreme heat waves. The results show that urban land use characteristics that have evolved over the past ~20 years in the Beijing-Tianjin-Hebei metropolitan area have had a significant impact on the extreme temperatures occurring during extreme heat events. Simulations show that new urban development has caused an intensification and expansion of the areas experiencing extreme heat waves with an average increase in temperature of approximately 0.60°C. This change is most obvious at night with an increase up to 0.95°C, for which the total contribution of anthropogenic heat is 34%. We also simulate the effects of geo-engineering strategies increasing the albedo of urban roofs. White roofs reflect a large fraction of incoming sunlight in the daytime, which reduced the net radiation so that the roof surface keep at a lower temperature than regular solar-absorptive roofs. Urban net radiation decreases by approximately 200 W m-2 at local noon because of high solar reflectance of white roofs, which cools the daytime urban temperature afer sunrise, with the largest decrease of almost -0.80°C at local noon. Moreover, the nighttime temperature also shows slightly cooler, approximately 0.2°C, because there is still considerable heat which is stored in the daytime released from urban surfaces at night. The results also suggest that increasing the albedo of urban roofs can reduce the urban mean temperature by approximately 0.51°C during summer extreme heat events. In urban areas, white roofs can counter 80% of the heat wave results from urban sprawl during the last 20 years. These results suggest that increasing the albedo of roofs in the Beijing-Tianjin-Hebei metropolitan area is an effective way of countering some hazards of heat waves. Using a regional climate model, we proposed that white roofs may be an effective strategy to complement urban heat wave mitigation efforts as a way of further slowing the rate of global temperature increase in response to continued greenhouse gas emissions.

Standards for the validation of remotely sensed albedo products

NASA Astrophysics Data System (ADS)

Adams, Jennifer

2015-04-01

Land surface albedo is important component of the Earth's energy balance, defined as the fraction of shortwave radiation absorbed by a surface, and is one many Essential Climate Variables (ECVS) that can be retrieved from space through remote sensing. To quantify the accuracy of these products, they must be validated with respect to in-situ measurements of albedo using an albedometer. Whilst accepted standards exist for the calibration of albedometers, standards for the use of in-situ measurement schemes, and their use in validation procedures have yet to be developed. It is essential that we can assess the quality of remotely sensed albedo data, and to identify traceable sources of uncertainty during process of providing these data. As a result of the current lack of accepted standards for in-situ albedo retrieval and validation procedures, we are not yet able to identify and quantify traceable sources of uncertainty. Establishing standard protocols for in-situ retrievals for the validation of global albedo products would allow inter-product use and comparison, in addition to product standardization. Accordingly, this study aims to assess the quality of in-situ albedo retrieval schemes and identify sources of uncertainty, specifically in vegetation environments. A 3D Monte Carlo Ray Tracing Model will be used to simulate albedometer instruments in complex 3D vegetation canopies. To determine sources of uncertainty, factors that influence albedo measurement uncertainty were identified and will subsequently be examined: 1. Time of day (Solar Zenith Angle) 2. Ecosytem type 3. Placement of albedometer within the ecosystem 4. Height of albedometer above the canopy 5. Clustering within the ecosystem A variety of 3D vegetation canopies have been generated to cover the main ecosystems found globally, different seasons, and different plant distributions. Canopies generated include birchstand and pinestand forests for summer and winter, savanna, shrubland, cropland and citrus orchard. All canopies were simulated for a 100x100m area to best represent in-situ measurement conditions. Preliminary tests have been conducted, firstly, identifying the spectral range required to estimate broadband albedo (BBA) and secondly, determining the hyper-spectral intervals required to calculate BBA from spectral albedo. Final results are expected to be able to identify for the factors aforementioned, given a specified confidence level and within 3% accuracy, when does uncertainty of in-situ measurement fall within these critera, and outside these criteria. As the uncertainty of in-situ measurements should be made on an individual basis accounting for relevant factors, this study aims to document for a specific scenario traceable uncertainty sources in in-situ albedo retrieval.

Branching out to residential lands: Missions and strategies of five tree distribution programs in the U.S.

Treesearch

Vi D. Nguyen; Lara A. Roman; Dexter H. Locke; Sarah K. Mincey; Jessica R. Sanders; Erica Smith Fichman; Mike Duran-Mitchell; Sarah Lumban Tobing

2017-01-01

Residential lands constitute a major component of existing and possible tree canopy in many cities in the United States. To expand the urban forest on these lands, some municipalities and nonprofit organizations have launched residential yard tree distribution programs, also known as tree giveaway programs. This paper describes the operations of five tree distribution...

Evaluation of the National Land Database for Hydrologic Applications in Urban And Suburban Baltimore, Maryland

Treesearch

Monica Lipscomb Smith; Weiqi Zhou; Mary Cadenasso; J. Morgan Grove; Lawrence Band

2010-01-01

We compared the National Land Cover Database (NLCD) 2001 land cover, impervious, and canopy data products to land cover data derived from 0.6-m resolution three-band digital imagery and ancillary data. We conducted this comparison at the 1 km2, 9 km2, and gauged watershed scales within the Baltimore Ecosystem Study to...

Measurements of upward turbulent ozone fluxes above a subalpine spruce-fir forest

Treesearch

Karl Zeller; Ted Hehn

1996-01-01

High rural concentrations of ozone (O3) are thought to be either stratospheric in origin, advected from upwind urban sources, or photochemically generated locally as a result of natural trace gas emissions. Ozone is known to be transported vertically downward from the above-canopy atmospheric surface layer and destroyed within stomata or on other biological and mineral...

Cryptic indirect effects of exurban edges on a woodland community

Treesearch

R. J. Warren; S. M. Pearson; S. Henry; K. Rossouw; J. P. Love; M. J. Olejniczak; Katherine Elliott; M. A. Bradford

2015-01-01

Exurban development (e.g., second homes) in woodlands spreads urban land use impacts beyond suburbs, but because exurban developments often retain many components of original ecosystem structure—such as a forest canopy rather than open lawn—their ecological impacts may be underestimated. Changes in seed-dispersing ant behavior prompted by exurban land use,...

Tree and impervious cover in the United States

Treesearch

David J. Nowak; Eric J. Greenfield

2012-01-01

Using aerial photograph interpretation of circa 2005 imagery, percent tree canopy and impervious surface cover in the conterminous United States are estimated at 34.2% (standard error (SE) = 0.2%) and 2.4% (SE = 0.1%), respectively. Within urban/community areas, percent tree cover (35.1%, SE = 0.4%) is similar to the national value, but percent impervious cover is...

Assembling a biogenic hydrocarbon emissions inventory for the SCOS97-NARSTO modeling domain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin, M.T.; Winer, A.M.; Karlik, J.

1998-12-31

To assist in developing ozone control strategies for Southern California, the California Air Resources Board is developing a biogenic hydrocarbon (BHC) emissions inventory model for the SCOS97-NARSTO domain. The basis for this bottom-up model is SCOS97-NARSTO-specific landuse and landcover maps, leafmass constants, and BHC emission rates. In urban areas, landuse maps developed by the Southern California Association of Governments, San Diego Association of Governments, and other local governments are used while in natural areas, landcover and plant community databases produced by the GAP Analysis Project (GAP) are employed. Plant identities and canopy volumes for species in each landuse and landcovermore » category are based on the most recent botanical field survey data. Where possible, experimentally determined leafmass constant and BHC emission rate measurements reported in the literature are used or, for those species where experimental data are not available, values are assigned based on taxonomic methods. A geographic information system is being used to integrate these databases, as well as the most recent environmental correction algorithms and canopy shading factors, to produce a spatially- and temporally-resolved BHC emission inventory suitable for input into the Urban Airshed Model.« less

Trees Grow on Money: Urban Tree Canopy Cover and Environmental Justice

PubMed Central

Schwarz, Kirsten; Fragkias, Michail; Boone, Christopher G.; Zhou, Weiqi; McHale, Melissa; Grove, J. Morgan; O’Neil-Dunne, Jarlath; McFadden, Joseph P.; Buckley, Geoffrey L.; Childers, Dan; Ogden, Laura; Pincetl, Stephanie; Pataki, Diane; Whitmer, Ali; Cadenasso, Mary L.

2015-01-01

This study examines the distributional equity of urban tree canopy (UTC) cover for Baltimore, MD, Los Angeles, CA, New York, NY, Philadelphia, PA, Raleigh, NC, Sacramento, CA, and Washington, D.C. using high spatial resolution land cover data and census data. Data are analyzed at the Census Block Group levels using Spearman’s correlation, ordinary least squares regression (OLS), and a spatial autoregressive model (SAR). Across all cities there is a strong positive correlation between UTC cover and median household income. Negative correlations between race and UTC cover exist in bivariate models for some cities, but they are generally not observed using multivariate regressions that include additional variables on income, education, and housing age. SAR models result in higher r-square values compared to the OLS models across all cities, suggesting that spatial autocorrelation is an important feature of our data. Similarities among cities can be found based on shared characteristics of climate, race/ethnicity, and size. Our findings suggest that a suite of variables, including income, contribute to the distribution of UTC cover. These findings can help target simultaneous strategies for UTC goals and environmental justice concerns. PMID:25830303

Removal of Polycyclic Aromatic Hydrocarbons from Precipitation in an Urban Forest of Guangzhou, South China.

PubMed

Chen, Bufeng; Pei, Nancai; Huang, Junbiao; Liu, Shuguang; Zhang, Na; Xiao, Yihua; Pan, Yongjun

2015-08-01

Polycyclic aromatic hydrocarbon (PAH) concentrations and fluxes were measured monthly in situ from rain events in an urban forest in the megapolitan city Guangzhou, China, to investigate impacts of forest canopy and soils on PAHs. Mean Σ9-PAH concentrations were 107.5, 101.6, 106.3, 107.1 and 42.4 ng L(-1) in precipitation, throughfall, seepage water at the 30 and 60 cm soil depth, and runoff, respectively, indicating a great decrease in the form of runoff. Meanwhile, annual fluxes of total PAHs decreased from precipitation (205.9 µg m(-2) year(-1)), to throughfall (156.3 µg m(-2) year(-1)), and to seepage water (65.3 µg m(-2) year(-1) at 30-cm soil depth and 7.5 µg m(-2) year(-1) at 60-cm soil depth), but increased in runoff (34.1 µg m(-2) year(-1)). When compared to precipitation, PAH fluxes decreased by 83.4% in runoff, with 29% contributed by forest canopy and 71% by soils. Soil biodegradation explained 18.2% of PAH reduction by the surface soil layer and 34.6% by the middle soil layer.

Scalar Dispersion from Point Sources in a Realistic Urban Environment

NASA Astrophysics Data System (ADS)

Salesky, S.; Giometto, M. G.; Christen, A.; Parlange, M. B.

2016-12-01

Accurate modeling of scalar dispersion within and above urban canopies is critical to properly predict air quality and dispersion (e.g. accidental contaminant release) in urban environments. We perform large eddy simulations (LES) of scalar dispersion from point sources in a typical North American neighborhood using topography and foliage density derived from airborne LIDAR scans with 1 m resolution in Vancouver, BC, Canada. The added drag force due to trees is parameterized in the LES as a function of the leaf area density (LAD) profile. Conversely, drag from buildings is accounted for using a direct forcing approach immersed-boundary method. The scalar advection-diffusion equation is discretized in a finite-volume framework, and accurate mass conservation is enforced through a recently developed Cartesian cut cell method. Simulations are performed with trees for different values of LAD, representative of summer and winter conditions, as well as a case without trees. The effects of varying mean wind direction (derived from observed wind climatologies) on dispersion patterns are also considered. Scalar release locations in the LES are informed by spatially distributed measurements of carbon dioxide concentration; CO2 is used as a tracer for fossil fuel emissions, since source strengths are well-known and the contribution from biological processes in this setting is small (<10%). The effects of leaf area density, source height, and wind direction on scalar statistics including the growth of the mean concentration plume and the fraction that escapes the urban canopy layer will be considered. In a companion study, the presence of trees was found to strongly modify sweep and ejection patterns for the momentum flux; here we consider the related issue of how vegetation influences coherent structures responsible for scalar transport.

Non-chemistry coupled PM10 modeling in Chiang Mai City, Northern Thailand: A fast operational approach for aerosol forecasts

NASA Astrophysics Data System (ADS)

Macatangay, Ronald; Bagtasa, Gerry; Sonkaew, Thiranan

2017-09-01

The Weather Research and Forecasting (WRF v. 3.7) model was applied to model PM10 data in Chiang Mai city for 10-days during a high haze event utilizing updated land use categories from the Moderate Resolution Imaging Spectroradiometer (MODIS). A higher resolution meteorological lateral boundary condition (from 1 degree to 0.25 degree) was also used from the NCEP GDAS/FNL Global Tropospheric Analyses and Forecast Grid system. A 3-category urban canopy model was also added and the Thompson aerosol-aware microphysics parameterization scheme was used to model the aerosol number concentrations that were later converted to PM10 concentrations. Aerosol number concentration monthly climatology was firstly used as initial and lateral boundary conditions to model PM10 concentrations. These were compared to surface data obtained from two stations of the Pollution Control Department (PCD) of Thailand. The results from the modeled PM10 concentrations could not capture the variability (r = 0.29; 0.27 for each site) and underestimated a high PM10 spike during the period studied. The authors then added satellite data to the aerosol climatology that improved the comparison with observations (r = 0.45; 43). However, both model runs still were not able to capture the high PM10 concentration event. This requires further investigation.

Effects of urban debris material on the extraction chromatographic separation of strontium: Part II: cement and concrete

DOE PAGES

McLain, Derek R.; Liu, Christine; Sudowe, Ralf

2017-11-02

The majority of radiochemical separation schemes available have been developed for environmental samples that are not necessarily representative of those found in an urban environment. However, it is much more likely that an incident involving a radiation dispersal device (RDD) would occur in an urban or metropolitan area. It is unclear if the currently available separation schemes would be effective in such an event. It is therefore important to determine if the current schemes would be adequate, or to find efficient and accurate ways to separate radiological material from urban debris. One important radiological material that could be used inmore » an RDD is 90Sr. Part I of this work investigated the effects steel had on strontium separations, while this work investigates cement and concrete. This research demonstrates that the individual elements present in a cement and concrete sample matrix can give rise to significant interferences with extraction chromatographic separations. In conclusion, solutions of the constituents mixed in representative ratios; however, show fewer problems« less

Effects of urban debris material on the extraction chromatographic separation of strontium: Part II: cement and concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

McLain, Derek R.; Liu, Christine; Sudowe, Ralf

The majority of radiochemical separation schemes available have been developed for environmental samples that are not necessarily representative of those found in an urban environment. However, it is much more likely that an incident involving a radiation dispersal device (RDD) would occur in an urban or metropolitan area. It is unclear if the currently available separation schemes would be effective in such an event. It is therefore important to determine if the current schemes would be adequate, or to find efficient and accurate ways to separate radiological material from urban debris. One important radiological material that could be used inmore » an RDD is 90Sr. Part I of this work investigated the effects steel had on strontium separations, while this work investigates cement and concrete. This research demonstrates that the individual elements present in a cement and concrete sample matrix can give rise to significant interferences with extraction chromatographic separations. In conclusion, solutions of the constituents mixed in representative ratios; however, show fewer problems« less

[Models for biomass estimation of four shrub species planted in urban area of Xi'an city, Northwest China].

PubMed

Yao, Zheng-Yang; Liu, Jian-Jun

2014-01-01

Four common greening shrub species (i. e. Ligustrum quihoui, Buxus bodinieri, Berberis xinganensis and Buxus megistophylla) in Xi'an City were selected to develop the highest correlation and best-fit estimation models for the organ (branch, leaf and root) and total biomass against different independent variables. The results indicated that the organ and total biomass optimal models of the four shrubs were power functional model (CAR model) except for the leaf biomass model of B. megistophylla which was logarithmic functional model (VAR model). The independent variables included basal diameter, crown diameter, crown diameter multiplied by height, canopy area and canopy volume. B. megistophylla significantly differed from the other three shrub species in the independent variable selection, which were basal diameter and crown-related factors, respectively.

The Effects of Fine-scale Soil Moisture and Canopy Heterogeneities on Energy and Soil Water Fluxes in a Temperate Mixed Deciduous Forest

NASA Astrophysics Data System (ADS)

He, L.; Ivanov, V. Y.; Bohrer, G.; Maurer, K.; Vogel, C. S.; Moghaddam, M.

2011-12-01

Vegetation is heterogeneous at different scales, influencing spatially variable energy and water exchanges between land-surface and atmosphere. Current land surface parameterizations of large-scale models consider spatial variability at a scale of a few kilometers and treat vegetation cover as aggregated patches with uniform properties. However, the coupling mechanisms between fine-scale soil moisture, vegetation, and energy fluxes such as evapotranspiration are strongly nonlinear; the aggregation of surface variations may produce biased energy fluxes. This study aims to improve the understanding of the scale impact in atmosphere-biosphere-hydrosphere interactions, which affects predictive capabilities of land surface models. The study uses a high-resolution, physically-based ecohydrological model tRIBS + VEGGIE as a data integration tool to upscale the heterogeneity of canopy distribution resolved at a few meters to the watershed scale. The study was carried out for a spatially heterogeneous, temperate mixed forest environment of Northern Michigan located near the University of Michigan Biological Station (UMBS). Energy and soil water dynamics were simulated at the tree-canopy resolution in the horizontal plane for a small domain (~2 sq. km) located within a footprint of the AmeriFlux tower. A variety of observational data were used to constrain and confirm the model, including a 3-m profile continuous soil moisture dataset and energy flux data (measured at the AmeriFlux tower footprint). A scenario with a spatially uniform canopy, corresponding to the commonly used 'big-leaf' scheme in land surface parameterizations was used to infer the effects of coarse-scale averaging. To gain insights on how heterogeneous canopy and soil moisture interact and contribute to the domain-averaged transpiration, several scenarios of tree-scale leaf area and soil moisture spatial variability were designed. Specifically, for the same mean states, the scenarios of variability of canopy biomass account for the spatial distribution of photosynthesis (and thus the stomatal resistance), the aerodynamic and leaf boundary layer resistances as well as the differential radiation forcing due to tall tree exposure and lateral shading of short trees. The numerical experiments show that by transpiring spatially varying amounts of water, heterogeneous canopies adjust the spatial soil water state to the scaled inverse of the canopy biomass regardless of the initial moisture state. Such a spatial distribution can be further wiped out because of the differential water stress. The aggregation of canopy-scale atmosphere-biosphere-hydrosphere interactions demonstrates non-linear relationship between soil moisture and evapotranspiration, influencing domain-averaged energy fluxes.

The contribution of urbanization to recent extreme heat events and a potential mitigation strategy in the Beijing-Tianjin-Hebei metropolitan area

NASA Astrophysics Data System (ADS)

Wang, Mingna; Yan, Xiaodong; Liu, Jiyuan; Zhang, Xuezhen

2013-11-01

This paper addresses the contribution of urban land use change to near-surface air temperature during the summer extreme heat events of the early twenty-first century in the Beijing-Tianjin-Hebei metropolitan area. This study uses the Weather Research Forecasting model with a single urban canopy model and the newest actual urban cover datasets. The results show that urban land use characteristics that have evolved over the past ~20 years in the Beijing-Tianjin-Hebei metropolitan area have had a significant impact on the extreme temperatures occurring during extreme heat events. Simulations show that new urban development has caused an intensification and expansion of the areas experiencing extreme heat waves with an average increase in temperature of approximately 0.60 °C. This change is most obvious at night with an increase up to 0.95 °C, for which the total contribution of anthropogenic heat is 34 %. We also simulate the effects of geo-engineering strategies increasing the albedo of urban roofs, an effective way of reducing urban heat island, which can reduce the urban mean temperature by approximately 0.51 °C and counter approximately 80 % of the heat wave results from urban sprawl during the last 20 years.

Connecting the failure of K-theory inside and above vegetation canopies and ejection-sweep cycles by a large eddy simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banerjee, Tirtha; De Roo, Frederik; Mauder, Matthias

Parameterizations of biosphere-atmosphere interaction processes in climate models and other hydrological applications require characterization of turbulent transport of momentum and scalars between vegetation canopies and the atmosphere, which is often modeled using a turbulent analogy to molecular diffusion processes. However, simple flux-gradient approaches (K-theory) fail for canopy turbulence. One cause is turbulent transport by large coherent eddies at the canopy scale, which can be linked to sweep-ejection events, and bear signatures of non-local organized eddy motions. K-theory, that parameterizes the turbulent flux or stress proportional to the local concentration or velocity gradient, fails to account for these non-local organized motions. The connection to sweep-ejection cycles and the local turbulent flux can be traced back to the turbulence triple momentmore » $$\\overline{C'W'W'}$$. In this work, we use large-eddy simulation to investigate the diagnostic connection between the failure of K-theory and sweep-ejection motions. Analyzed schemes are quadrant analysis (QA) and a complete and incomplete cumulant expansion (CEM and ICEM) method. The latter approaches introduce a turbulence timescale in the modeling. Furthermore, we find that the momentum flux needs a different formulation for the turbulence timescale than the sensible heat flux. In conclusion, accounting for buoyancy in stratified conditions is also deemed to be important in addition to accounting for non-local events to predict the correct momentum or scalar fluxes.« less

Connecting the failure of K-theory inside and above vegetation canopies and ejection-sweep cycles by a large eddy simulation

DOE PAGES

Banerjee, Tirtha; De Roo, Frederik; Mauder, Matthias

2017-10-19

Parameterizations of biosphere-atmosphere interaction processes in climate models and other hydrological applications require characterization of turbulent transport of momentum and scalars between vegetation canopies and the atmosphere, which is often modeled using a turbulent analogy to molecular diffusion processes. However, simple flux-gradient approaches (K-theory) fail for canopy turbulence. One cause is turbulent transport by large coherent eddies at the canopy scale, which can be linked to sweep-ejection events, and bear signatures of non-local organized eddy motions. K-theory, that parameterizes the turbulent flux or stress proportional to the local concentration or velocity gradient, fails to account for these non-local organized motions. The connection to sweep-ejection cycles and the local turbulent flux can be traced back to the turbulence triple momentmore » $$\\overline{C'W'W'}$$. In this work, we use large-eddy simulation to investigate the diagnostic connection between the failure of K-theory and sweep-ejection motions. Analyzed schemes are quadrant analysis (QA) and a complete and incomplete cumulant expansion (CEM and ICEM) method. The latter approaches introduce a turbulence timescale in the modeling. Furthermore, we find that the momentum flux needs a different formulation for the turbulence timescale than the sensible heat flux. In conclusion, accounting for buoyancy in stratified conditions is also deemed to be important in addition to accounting for non-local events to predict the correct momentum or scalar fluxes.« less

The interactions between soil-biosphere-atmosphere land surface model with a multi-energy balance (ISBA-MEB) option in SURFEXv8 - Part 1: Model description

NASA Astrophysics Data System (ADS)

Boone, Aaron; Samuelsson, Patrick; Gollvik, Stefan; Napoly, Adrien; Jarlan, Lionel; Brun, Eric; Decharme, Bertrand

2017-02-01

Land surface models (LSMs) are pushing towards improved realism owing to an increasing number of observations at the local scale, constantly improving satellite data sets and the associated methodologies to best exploit such data, improved computing resources, and in response to the user community. As a part of the trend in LSM development, there have been ongoing efforts to improve the representation of the land surface processes in the interactions between the soil-biosphere-atmosphere (ISBA) LSM within the EXternalized SURFace (SURFEX) model platform. The force-restore approach in ISBA has been replaced in recent years by multi-layer explicit physically based options for sub-surface heat transfer, soil hydrological processes, and the composite snowpack. The representation of vegetation processes in SURFEX has also become much more sophisticated in recent years, including photosynthesis and respiration and biochemical processes. It became clear that the conceptual limits of the composite soil-vegetation scheme within ISBA had been reached and there was a need to explicitly separate the canopy vegetation from the soil surface. In response to this issue, a collaboration began in 2008 between the high-resolution limited area model (HIRLAM) consortium and Météo-France with the intention to develop an explicit representation of the vegetation in ISBA under the SURFEX platform. A new parameterization has been developed called the ISBA multi-energy balance (MEB) in order to address these issues. ISBA-MEB consists in a fully implicit numerical coupling between a multi-layer physically based snowpack model, a variable-layer soil scheme, an explicit litter layer, a bulk vegetation scheme, and the atmosphere. It also includes a feature that permits a coupling transition of the snowpack from the canopy air to the free atmosphere. It shares many of the routines and physics parameterizations with the standard version of ISBA. This paper is the first of two parts; in part one, the ISBA-MEB model equations, numerical schemes, and theoretical background are presented. In part two (Napoly et al., 2016), which is a separate companion paper, a local scale evaluation of the new scheme is presented along with a detailed description of the new forest litter scheme.

Urban trees and forests of the Chicago region

Treesearch

David J. Nowak; Robert E. III Hoehn; Allison R. Bodine; Daniel E. Crane; John F. Dwyer; Veta Bonnewell; Gary Watson

2013-01-01

An analysis of trees in the Chicago region of Illinois reveals that this area has about 157,142,000 trees with tree and shrub canopy that covers 21.0 percent of the region. The most common tree species are European buckthorn, green ash, boxelder, black cherry, and American elm. Trees in the Chicago region currently store about 16.9 million tons of carbon (61.9 million...

Community ash densities and economic impact potential of emerald ash borer (Agrilus planipennis) in four midwestern states

Treesearch

T. Davis Sydnor; Matthew Bumgardner; Sakthi. Subburayalu

2011-01-01

A survey of 586 community representatives with urban tree canopy responsibilities was conducted to provide data on ash density within four states in the Midwestern U.S., and to examine potential economic losses should emerald ash borer (EAB) become established in their communities. One hundred twenty-three responses were received from communities of various sizes. Data...

Assessing urban forest effects and values: Douglas County, Kansas

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. Hoehn; Alexis Ellis; Kim Bomberger; Daniel E. Crane; Theodore A. Endreny; Thomas Taggert; Emily. Stephan

2014-01-01

An analysis of trees in Douglas County, Kansas, reveals that this area has about 14,164,000 trees with tree and shrub canopy that covers 25.2 percent of the county. The most common tree species are American elm, northern hackberry, eastern redcedar, Osage-orange, and honeylocust. Trees in Douglas County currently store about 1.7 million tons of carbon (6.4 million tons...

Land fragmentationn and impacts to streams and fish in the central and upper midwest

Treesearch

Elon S. Verry

2000-01-01

Fragmentation of the land means changes in the vegetative cover. This alone has caused significant and wide spread physical and water quality changes to the streams and rivers in the central and upper Midwest. Removal of the forest canopy that changes land use to "open" conditions: agricultural, urban, or rights of way, is sufficient to initiate and prolong...

Assessing urban forest effects and values: the greater Kansas City region

Treesearch

David J. Nowak; Allison R. Bodine; Robert E. III Hoehn; Daniel E. Crane; Alexis Ellis; Theodore A. Endreny; Yang Yang; Tom Jacobs; Kassie Shelton

2013-01-01

An analysis of trees in the greater Kansas City region of Missouri and Kansas reveals that this area has about 249,450,000 trees with tree and shrub canopy that covers 28.3 percent of the region. The most common tree species are American elm, northern hackberry, Osage-orange, honeylocust, and eastern redcedar. Trees in the greater Kansas City region currently store...

Coupled carbon-water exchange of the Amazon rain forest, I. Model description, parameterization and sensitivity analysis

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Ganzeveld, L.; Kesselmeier, J.

2005-04-01

Detailed one-dimensional multilayer biosphere-atmosphere models, also referred to as CANVEG models, are used for more than a decade to describe coupled water-carbon exchange between the terrestrial vegetation and the lower atmosphere. Within the present study, a modified CANVEG scheme is described. A generic parameterization and characterization of biophysical properties of Amazon rain forest canopies is inferred using available field measurements of canopy structure, in-canopy profiles of horizontal wind speed and radiation, canopy albedo, soil heat flux and soil respiration, photosynthetic capacity and leaf nitrogen as well as leaf level enclosure measurements made on sunlit and shaded branches of several Amazonian tree species during the wet and dry season. The sensitivity of calculated canopy energy and CO2 fluxes to the uncertainty of individual parameter values is assessed. In the companion paper, the predicted seasonal exchange of energy, CO2, ozone and isoprene is compared to observations.

A bi-modal distribution of leaf area density with a total leaf area index of 6 is inferred from several observations in Amazonia. Predicted light attenuation within the canopy agrees reasonably well with observations made at different field sites. A comparison of predicted and observed canopy albedo shows a high model sensitivity to the leaf optical parameters for near-infrared short-wave radiation (NIR). The predictions agree much better with observations when the leaf reflectance and transmission coefficients for NIR are reduced by 25-40%. Available vertical distributions of photosynthetic capacity and leaf nitrogen concentration suggest a low but significant light acclimation of the rain forest canopy that scales nearly linearly with accumulated leaf area.

Evaluation of the biochemical leaf model, using the enclosure measurements, showed that recommended parameter values describing the photosynthetic light response, have to be optimized. Otherwise, predicted net assimilation is overestimated by 30-50%. Two stomatal models have been tested, which apply a well established semi-empirical relationship between stomatal conductance and net assimilation. Both models differ in the way they describe the influence of humidity on stomatal response. However, they show a very similar performance within the range of observed environmental conditions. The agreement between predicted and observed stomatal conductance rates is reasonable. In general, the leaf level data suggests seasonal physiological changes, which can be reproduced reasonably well by assuming increased stomatal conductance rates during the wet season, and decreased assimilation rates during the dry season.

The sensitivity of the predicted canopy fluxes of energy and CO2 to the parameterization of canopy structure, the leaf optical parameters, and the scaling of photosynthetic parameters is relatively low (1-12%), with respect to parameter uncertainty. In contrast, modifying leaf model parameters within their uncertainty range results in much larger changes of the predicted canopy net fluxes (5-35%).

Coupled carbon-water exchange of the Amazon rain forest, I. Model description, parameterization and sensitivity analysis

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Ganzeveld, L.; Kesselmeier, J.

2005-09-01

Detailed one-dimensional multilayer biosphere-atmosphere models, also referred to as CANVEG models, are used for more than a decade to describe coupled water-carbon exchange between the terrestrial vegetation and the lower atmosphere. Within the present study, a modified CANVEG scheme is described. A generic parameterization and characterization of biophysical properties of Amazon rain forest canopies is inferred using available field measurements of canopy structure, in-canopy profiles of horizontal wind speed and radiation, canopy albedo, soil heat flux and soil respiration, photosynthetic capacity and leaf nitrogen as well as leaf level enclosure measurements made on sunlit and shaded branches of several Amazonian tree species during the wet and dry season. The sensitivity of calculated canopy energy and CO2 fluxes to the uncertainty of individual parameter values is assessed. In the companion paper, the predicted seasonal exchange of energy, CO2, ozone and isoprene is compared to observations.

A bi-modal distribution of leaf area density with a total leaf area index of 6 is inferred from several observations in Amazonia. Predicted light attenuation within the canopy agrees reasonably well with observations made at different field sites. A comparison of predicted and observed canopy albedo shows a high model sensitivity to the leaf optical parameters for near-infrared short-wave radiation (NIR). The predictions agree much better with observations when the leaf reflectance and transmission coefficients for NIR are reduced by 25-40%. Available vertical distributions of photosynthetic capacity and leaf nitrogen concentration suggest a low but significant light acclimation of the rain forest canopy that scales nearly linearly with accumulated leaf area.

Evaluation of the biochemical leaf model, using the enclosure measurements, showed that recommended parameter values describing the photosynthetic light response, have to be optimized. Otherwise, predicted net assimilation is overestimated by 30-50%. Two stomatal models have been tested, which apply a well established semi-empirical relationship between stomatal conductance and net assimilation. Both models differ in the way they describe the influence of humidity on stomatal response. However, they show a very similar performance within the range of observed environmental conditions. The agreement between predicted and observed stomatal conductance rates is reasonable. In general, the leaf level data suggests seasonal physiological changes, which can be reproduced reasonably well by assuming increased stomatal conductance rates during the wet season, and decreased assimilation rates during the dry season.

The sensitivity of the predicted canopy fluxes of energy and CO2 to the parameterization of canopy structure, the leaf optical parameters, and the scaling of photosynthetic parameters is relatively low (1-12%), with respect to parameter uncertainty. In contrast, modifying leaf model parameters within their uncertainty range results in much larger changes of the predicted canopy net fluxes (5-35%).

Ground and flight test program of a Stokes-flow parachute: Packaging, deployment, and sounding rocket integration

NASA Technical Reports Server (NTRS)

Niederer, P. G.; Mihora, D. J.

1972-01-01

The current design and hardware components of the patented 14 sqm Stokes flow parachute are described. The Stokes-flow parachute is a canopy of open mesh material, which is kept deployed by braces. Because of the light weight of its mesh material, and the high drag on its mesh elements when they operate in the Stokes-flow flight regime, this parachute has an extremely low ballistic coefficient. It provides a stable aerodynamic platform superior to conventional nonporous billowed parachutes, is exceptionally packable, and is easily contained within the canister of the Sidewinder Arcas or the RDT and E rockets. Thus, it offers the potential for gathering more meteorological data, especially at high altitudes, than conventional billowed parachutes. Methods for packaging the parachute are also recommended. These methods include schemes for folding the canopy and for automatically releasing the pressurizing fluid as the packaged parachute unfolds.

Variability in snowpack accumulation and ablation associated with mountain pine beetle infestation in western forests

NASA Astrophysics Data System (ADS)

Biederman, J. A.; Harpold, A. A.; Gochis, D. J.; Reed, D.; Brooks, P. D.

2010-12-01

Seasonal snowcover is a primary source of water to urban and agricultural regions in the western United States, where Mountain Pine Beetle (MPB) has caused rapid and extensive changes to vegetation in montane forests. Levels of MPB infestation in these seasonally snow-covered systems are unprecedented, and it is unknown how this will affect water yield, especially in changing climate conditions. To address this unknown we ask: How does snow accumulation and ablation vary across forest with differing levels of impact? Our study areas in the Rocky Mountains of CO and WY are similar in latitude, elevation and forest structure before infestation, but they vary in the intensity and timing of beetle infestation and tree mortality. We present a record for winter 2010 that includes continuous snow depth as well as stand-scale snow surveys at maximum accumulation. Additional measurements include snowfall, net radiation, temperature and wind speed as well as characterization of forest structure by leaf area index. In a stand uninfested by MPB, maximum snow depth was fairly uniform under canopy (mean = 86 cm, coefficient of variation = 0.021), while canopy gaps showed greater and more variable depth (mean = 117 cm, CV = 0.111). This is consistent with several studies demonstrating that snowfall into canopy gaps depends upon gap size, orientation, wind speed and storm size. In a stand impacted in 2007, snow depth under canopy was less uniform, and there were smaller differences in both mean depth and variability between canopy (mean = 93 cm, CV = 0.072) and gaps (mean = 97 cm, CV = 0.070), consistent with decreased canopy density. In a more recently infested (2009) stand with an intermediate level of MPB impact, mean snow depths were similar between canopy (96 cm, CV = 0.016) and gaps (95 cm, CV = 0.185) but gaps showed much greater variability, suggesting controls similar to those in effect in the uninfested stand. We further use these data to model snow accumulation and ablation as a function of vegetation, topography and fine-scale climate variability, with preliminary results presented at the meeting.

Could urban greening mitigate suburban thermal inequity?: the role of residents’ dispositions and household practices

NASA Astrophysics Data System (ADS)

Byrne, Jason; Ambrey, Christopher; Portanger, Chloe; Lo, Alex; Matthews, Tony; Baker, Douglas; Davison, Aidan

2016-09-01

Over the past decade research on urban thermal inequity has grown, with a focus on denser built environments. In this letter we examine thermal inequity associated with climate change impacts and changes to urban form in a comparatively socio-economically disadvantaged Australian suburb. Local urban densification policies designed to counteract sprawl have reduced block sizes, increased height limits, and diminished urban tree canopy cover (UTC). Little attention has been given to the combined effects of lower UTC and increased heat on disadvantaged residents. Such impacts include rising energy expenditure to maintain thermal comfort (i.e. cooling dwellings). We used a survey of residents (n = 230) to determine their perceptions of climate change impacts; household energy costs; household thermal comfort practices; and dispositions towards using green infrastructure to combat heat. Results suggest that while comparatively disadvantaged residents spend more on energy as a proportion of their income, they appear to have reduced capacity to adapt to climate change at the household scale. We found most residents favoured more urban greening and supported tree planting in local parks and streets. Findings have implications for policy responses aimed at achieving urban climate justice.

The influence of roadside solid and vegetation barriers on near-road air quality

NASA Astrophysics Data System (ADS)

Ghasemian, Masoud; Amini, Seyedmorteza; Princevac, Marko

2017-12-01

The current study evaluates the influence of roadside solid and vegetation barriers on the near-road air quality. Reynolds Averaged Navier-Stokes (RANS) technique coupled with the k - ε realizable turbulence model is utilized to investigate the flow pattern and pollutant concentration. A scalar transport equation is solved for a tracer gas to represent the roadway pollutant emissions. In addition, a broad range of turbulent Schmidt numbers are tested to calibrate the scalar transport equation. Three main scenarios including flat terrain, solid barrier, and vegetative barrier are studied. To validate numerical methodology, predicted pollutant concentration is compared with published wind tunnel data. Results show that the solid barrier induces an updraft motion and lofts the vehicle emission plume. Therefore, the ground-level pollutant concentration decreases compared to the flat terrain. For the vegetation barrier, different sub-scenarios with different vegetation densities ranging from approximately flat terrain to nearly solid barrier are examined. Dense canopies act in a similar manner as a solid barrier and mitigate the pollutant concentration through vertical mixing. On the other hand, the high porosity vegetation barriers reduce the wind speed and lead to a higher pollutant concentration. As the vegetation density increases, i.e. the barrier porosity decreases, the recirculation zone behind the canopy becomes larger and moves toward the canopy. The dense plant canopy with LAD = 3.33m-2m3 can improve the near-road air quality by 10% and high porosity canopy with LAD = 1m-2m3 deteriorates near-road air quality by 15%. The results of this study can be implemented as green infrastructure design strategies by urban planners and forestry organizations.

Large-Eddy Simulation of Coherent Flow Structures within a Cubical Canopy

NASA Astrophysics Data System (ADS)

Inagaki, Atsushi; Castillo, Marieta Cristina L.; Yamashita, Yoshimi; Kanda, Manabu; Takimoto, Hiroshi

2012-02-01

Instantaneous flow structures "within" a cubical canopy are investigated via large-eddy simulation. The main topics of interest are, (1) large-scale coherent flow structures within a cubical canopy, (2) how the structures are coupled with the turbulent organized structures (TOS) above them, and (3) the classification and quantification of representative instantaneous flow patterns within a street canyon in relation to the coherent structures. We use a large numerical domain (2,560 m × 2,560 m × 1,710 m) with a fine spatial resolution (2.5 m), thereby simulating a complete daytime atmospheric boundary layer (ABL), as well as explicitly resolving a regular array of cubes (40 m in height) at the surface. A typical urban ABL is numerically modelled. In this situation, the constant heat supply from roof and floor surfaces sustains a convective mixed layer as a whole, but strong wind shear near the canopy top maintains the surface layer nearly neutral. The results reveal large coherent structures in both the velocity and temperature fields "within" the canopy layer. These structures are much larger than the cubes, and their shapes and locations are shown to be closely related to the TOS above them. We classify the instantaneous flow patterns in a cavity, specifically focusing on two characteristic flow patterns: flushing and cavity-eddy events. Flushing indicates a strong upward motion, while a cavity eddy is characterized by a dominant vortical motion within a single cavity. Flushing is clearly correlated with the TOS above, occurring frequently beneath low-momentum streaks. The instantaneous momentum and heat transport within and above a cavity due to flushing and cavity-eddy events are also quantified.

Influences of different land use spatial control schemes on farmland conversion and urban development.

PubMed

Zhou, Min; Tan, Shukui; Zhang, Lu

2015-01-01

Land use planning is always officially implemented as an effective tool to control urban development and protect farmland. However, its impact on land use change remains untested in China. Using a case study of Hang-Jia-Hu region, the main objective of this paper was to investigate the influence of different land use spatial control schemes on farmland conversion and urban development. Comparisons of farmland conversion and urban development patterns between the urban planning area and the non-urban planning area were characterized by using remote sensing, geographical information systems, and landscape metrics. Results indicated that farmland conversion in the non-urban planning area was more intensive than that in the urban planning area, and that farmland patterns was more fragmented in the non-urban planning area. Built-up land patterns in the non-urban planning area showed a trend of aggregation, while those in the urban planning area had a dual trend of fragmentation and aggregation. Existing built-up areas had less influence on built-up land sprawl in the non-urban planning area than that in the urban planning area. Built-up land sprawl in the form of continuous development in the urban planning area led to farmland conversion; and in the non-urban planning area, built-up land sprawl in the form of leapfrogging development resulted in farmland areal declines and fragmentation. We argued that it is a basic requirement to integrate land use plans in urban and non-urban planning areas for land use planning and management.

Influences of Different Land Use Spatial Control Schemes on Farmland Conversion and Urban Development

PubMed Central

Zhou, Min; Tan, Shukui; Zhang, Lu

2015-01-01

Land use planning is always officially implemented as an effective tool to control urban development and protect farmland. However, its impact on land use change remains untested in China. Using a case study of Hang-Jia-Hu region, the main objective of this paper was to investigate the influence of different land use spatial control schemes on farmland conversion and urban development. Comparisons of farmland conversion and urban development patterns between the urban planning area and the non-urban planning area were characterized by using remote sensing, geographical information systems, and landscape metrics. Results indicated that farmland conversion in the non-urban planning area was more intensive than that in the urban planning area, and that farmland patterns was more fragmented in the non-urban planning area. Built-up land patterns in the non-urban planning area showed a trend of aggregation, while those in the urban planning area had a dual trend of fragmentation and aggregation. Existing built-up areas had less influence on built-up land sprawl in the non-urban planning area than that in the urban planning area. Built-up land sprawl in the form of continuous development in the urban planning area led to farmland conversion; and in the non-urban planning area, built-up land sprawl in the form of leapfrogging development resulted in farmland areal declines and fragmentation. We argued that it is a basic requirement to integrate land use plans in urban and non-urban planning areas for land use planning and management. PMID:25915897

Nested High Resolution Modeling of the Impact of Urbanization on Regional Climate in Three Vast Urban Agglomerations in China

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei; Hu, Yonghong; Jia, Gensuo

2013-04-01

In this paper, the Weather Research and Forecasting (WRF) model coupled to the Urban Canopy Model (UCM) is employed to simulate the impact of urbanization on the regional climate over three vast city agglomerations in China. Based on high resolution land use and land cover data, two scenarios are designed to represent the non-urban and current urban land use distributions. By comparing the results of two nested, high resolution numerical experiments, the spatial and temporal changes on surface air temperature, heat stress index, surface energy budget and precipitation due to urbanization are analyzed and quantified. Urban expansion increases the surface air temperature in urban areas by about 1? and this climatic forcing of urbanization on temperature is more pronounced in summer and nighttime than other seasons and daytime. The heat stress intensity, which reflects the combined effects of temperature and humidity, is enhanced by about 0.5 units in urban areas. The regional incoming solar radiation increases after urban expansion, which may be caused by the reduction of cloud fraction. The increased temperature and roughness of the urban surface lead to enhanced convergence. Meanwhile, the planetary boundary layer is deepened and water vapor is mixed more evenly in the lower atmosphere. The deficit of water vapor leads to less convective available potential energy and more convective inhibition energy. Finally, these combined effects may reduce the rainfall amount over urban area mainly in summer and change the regional precipitation pattern to a certain extent.

Simulating Energy, Water and Carbon Fluxes at the Shortgrass Steppe Long Term Ecological Research (LTER) Site

NASA Astrophysics Data System (ADS)

Beltran-Przekurat, A. B.; Pielke, R. A.; Morgan, J. A.; Burke, I. C.

2005-12-01

Coupled atmospheric-biospheric models are a particularly valuable tool for studying the potential effects of land-use and land-cover changes on the near-surface atmosphere since the atmosphere and biosphere are allowed to dynamically interact through the surface and canopy energy balance. GEMRAMS is a coupled atmospheric-biospheric model comprised of an atmospheric model, RAMS, and an ecophysiological process-based model, GEMTM. In the first part of this study, the soil-vegetation-atmosphere-transfer (SVAT) scheme, LEAF2, from RAMS, coupled with GEMTM, are used to simulate energy, water and carbon fluxes over different cropping systems (winter wheat and irrigated corn) and over a mixed C3/C4 shortgrass prairie located at the USDA-ARS Central Plains Experimental Range near Nunn, Colorado, the LTER Shortgrass Steppe site. The new SVAT scheme, GEMLEAF, is forced with air temperature and humidity, wind speed and photosynthetic active radiation (PAR). Calculated canopy temperature and relative humidity, soil moisture and temperature and PAR are used to compute sunlit/shaded leaf photosynthesis (for C3 and C4 plant types) and respiration. Photosynthate is allocated to leaves, shoots, roots and reproductive organs with variable partition coefficients, which are functions of soil water conditions. As water stress increases, the fraction of photosynthate allocated to root growth increases. Leaf area index (LAI) is estimated from daily leaf biomass growth, using the vegetation-prescribed specific leaf area. Canopy conductance, computed and based on photosynthesis and relative humidity, is used to calculate latent heat flux. Simulated energy and CO2 fluxes are compared to observations collected using Bowen ratio flux towers during two growing seasons. Seasonality of the fluxes reflecting different plant phenologies agrees well with the observed patterns. In the second part of this study, simulations for two clear days are performed with GEMRAMS over a model domain centered at the SGS site. Simulated spatial differences in the energy fluxes can be associated with the highly heterogeneous landscape in this area.

Vegetation species composition and canopy architecture information expressed in leaf water absorption measured in the 1000 nm and 2200 spectral region by an imaging spectrometer

NASA Technical Reports Server (NTRS)

Green, Robert O.; Roberts, Dar A.

1995-01-01

Plant species composition and plant architectural attributes are critical parameters required for the measuring, monitoring, and modeling of terrestrial ecosystems. Remote sensing is commonly cited as an important tool for deriving vegetation properties at an appropriate scale for ecosystem studies, ranging from local to regional and even synoptic scales. Classical approaches rely on vegetation indices such as the normalized difference vegetation index (NDVI) to estimate biophysical parameters such as leaf area index or intercepted photosynthetically active radiation (IPAR). Another approach is to apply a variety of classification schemes to map vegetation and thus extrapolate fine-scale information about specific sites to larger areas of similar composition. Imaging spectrometry provides additional information that is not obtainable through broad-band sensors and that may provide improved inputs both to direct biophysical estimates as well as classification schemes. Some of this capability has been demonstrated through improved discrimination of vegetation, estimates of canopy biochemistry, and liquid water estimates from vegetation. We investigate further the potential of leaf water absorption estimated from Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data as a means for discriminating vegetation types and deriving canopy architectural information. We expand our analysis to incorporate liquid water estimates from two spectral regions, the 1000-nm region and the 2200-nm region. The study was conducted in the vicinity of Jasper Ridge, California, which is located on the San Francisco peninsula to the west of the Stanford University campus. AVIRIS data were acquired over Jasper Ridge, CA, on June 2, 1992, at 19:31 UTC. Spectra from three sites in this image were analyzed. These data are from an area of healthy grass, oak woodland, and redwood forest, respectively. For these analyses, the AVIRIS-measured upwelling radiance spectra for the entire Jasper Ridge scene were transformed to apparent surface reflectance using a radiative transfer code-based inversion algorithm.

Spatial Growth Modeling and High Resolution Remote Sensing Data Coupled with Air Quality Modeling to Assess the Impact of Atlanta, Georgia on the Local and Regional Environment

NASA Technical Reports Server (NTRS)

Quattrochi, Dale A.; Estes, Maurice G., Jr.; Crosson, William; Johnson, Hoyt; Khan, Maudood

2006-01-01

The growth of cities, both in population and areal extent, appears as an inexorable process. Urbanization continues at a rapid rate, and it is estimated that by the year 2025, 60 percent of the world s population will live in cities. Urban expansion has profound impacts on a host of biophysical, environmental, and atmospheric processes within an urban ecosystems perspective. A reduction in air quality over cities is a major result of these impacts. Because of its complexity, the urban landscape is not adequately captured in air quality models such as the Community Multiscale Air Quality (CMAQ) model that is used to assess whether urban areas are in attainment of EPA air quality standards, primarily for ground level ozone. This inadequacy of the CMAQ model to sufficiently respond to the heterogeneous nature of the urban landscape can impact how well the model predicts ozone levels over metropolitan areas and ultimately, whether cities exceed EPA ozone air quality standards. We are exploring the utility of high-resolution remote sensing data and urban spatial growth modeling (SGM) projections as improved inputs to a meteorological/air quality modeling system focusing on the Atlanta, Georgia metropolitan area as a case study. These growth projections include business as usual and smart growth scenarios out to 2030. The growth projections illustrate the effects of employing urban heat island mitigation strategies, such as increasing tree canopy and albedo across the Atlanta metro area, which in turn, are used to model how air temperature can potentially be moderated as impacts on elevating ground-level ozone, as opposed to not utilizing heat island mitigation strategies. The National Land Cover Dataset at 30m resolution is being used as the land use/land cover input and aggregated to the 4km scale for the MM5 mesoscale meteorological model and the CMAQ modeling schemes. Use of these data has been found to better characterize low density/suburban development as compared with USGS lkm land use/land cover data that have traditionally been used in modeling. Air quality prediction for future scenarios to 2030 is being facilitated by land use projections using a spatial growth model. Land use projections were developed using the 2030 Regional Transportation Plan developed by the Atlanta Regional Commission, the regional planning agency for the area. This allows the Georgia Environmental Protection Division to evaluate how these transportation plans will affect future air quality. The coupled SGM and air quality modeling approach provides insight on what the impacts of Atlanta s growth will be on the local and regional environment and exists as a mechanism that can be used by policy makers to make rational decisions on urban growth and sustainability for the metropolitan area in the future.

Remote Sensing and Spatial Growth Modeling Coupled With Air Quality Modeling to Assess the Impact of Atlanta, Georgia on the Local and Regional Environment

NASA Astrophysics Data System (ADS)

Quattrochi, D. A.; Estes, M. G.; Crosson, W. L.; Johnson, H.; Khan, M.

2006-05-01

The growth of cities, both in population and areal extent, appears as an inexorable process. Urbanization continues at a rapid rate, and it is estimated that by the year 2025, 60 percent of the world's population will live in cities. Urban expansion has profound impacts on a host of biophysical, environmental, and atmospheric processes within an urban ecosystems perspective. A reduction in air quality over cities is a major result of these impacts. Because of its complexity, the urban landscape is not adequately captured in air quality models such as the Community Multiscale Air Quality (CMAQ) model that is used to assess whether urban areas are in attainment of EPA air quality standards, primarily for ground level ozone. This inadequacy of the CMAQ model to sufficiently respond to the heterogeneous nature of the urban landscape can impact how well the model predicts ozone levels over metropolitan areas and ultimately, whether cities exceed EPA ozone air quality standards. We are exploring the utility of high-resolution remote sensing data and urban spatial growth modeling (SGM) projections as improved inputs to a meteorological/air quality modeling system focusing on the Atlanta, Georgia metropolitan area as a case study. These growth projections include "business as usual" and "smart growth" scenarios out to 2030. The growth projections illustrate the effects of employing urban heat island mitigation strategies, such as increasing tree canopy and albedo across the Atlanta metro area, which in turn, are used to model how air temperature can potentially be moderated as impacts on elevating ground-level ozone, as opposed to not utilizing heat island mitigation strategies. The National Land Cover Dataset at 30m resolution is being used as the land use/land cover input and aggregated to the 4km scale for the MM5 mesoscale meteorological model and the CMAQ modeling schemes. Use of these data has been found to better characterize low density/suburban development as compared with USGS 1km land use/land cover data that have traditionally been used in modeling. Air quality prediction for future scenarios to 2030 is being facilitated by land use projections using a spatial growth model. Land use projections were developed using the 2030 Regional Transportation Plan developed by the Atlanta Regional Commission, the regional planning agency for the area. This allows the Georgia Environmental Protection Division to evaluate how these transportation plans will affect future air quality. The coupled SGM and air quality modeling approach provides insight on what the impacts of Atlanta's growth will be on the local and regional environment and exists as a mechanism that can be used by policy makers to make rational decisions on urban growth and sustainability for the metropolitan area in the future.

An ecology of prestige in New York City: Examining the relationships among population density, socio-economic status, group identity, and residential canopy cover

Treesearch

J. Morgan Grove; Dexter H. Locke; Jarlath P.M. O' Neil-Dunne

2014-01-01

Several social theories have been proposed to explain the uneven distribution of vegetation in urban residential areas: population density, social stratification, luxury effect, and ecology of prestige. We evaluate these theories using a combination of demographic and socio-economic predictors of vegetative cover on all residential lands in New York City. We use...

Thermal Remote Sensing with Uav-Based Workflows

NASA Astrophysics Data System (ADS)

Boesch, R.

2017-08-01

Climate change will have a significant influence on vegetation health and growth. Predictions of higher mean summer temperatures and prolonged summer draughts may pose a threat to agriculture areas and forest canopies. Rising canopy temperatures can be an indicator of plant stress because of the closure of stomata and a decrease in the transpiration rate. Thermal cameras are available for decades, but still often used for single image analysis, only in oblique view manner or with visual evaluations of video sequences. Therefore remote sensing using a thermal camera can be an important data source to understand transpiration processes. Photogrammetric workflows allow to process thermal images similar to RGB data. But low spatial resolution of thermal cameras, significant optical distortion and typically low contrast require an adapted workflow. Temperature distribution in forest canopies is typically completely unknown and less distinct than for urban or industrial areas, where metal constructions and surfaces yield high contrast and sharp edge information. The aim of this paper is to investigate the influence of interior camera orientation, tie point matching and ground control points on the resulting accuracy of bundle adjustment and dense cloud generation with a typically used photogrammetric workflow for UAVbased thermal imagery in natural environments.

Modelling temporal variance of component temperatures and directional anisotropy over vegetated canopy

NASA Astrophysics Data System (ADS)

Bian, Zunjian; du, yongming; li, hua

2016-04-01

Land surface temperature (LST) as a key variable plays an important role on hydrological, meteorology and climatological study. Thermal infrared directional anisotropy is one of essential factors to LST retrieval and application on longwave radiance estimation. Many approaches have been proposed to estimate directional brightness temperatures (DBT) over natural and urban surfaces. While less efforts focus on 3-D scene and the surface component temperatures used in DBT models are quiet difficult to acquire. Therefor a combined 3-D model of TRGM (Thermal-region Radiosity-Graphics combined Model) and energy balance method is proposed in the paper for the attempt of synchronously simulation of component temperatures and DBT in the row planted canopy. The surface thermodynamic equilibrium can be final determined by the iteration strategy of TRGM and energy balance method. The combined model was validated by the top-of-canopy DBTs using airborne observations. The results indicated that the proposed model performs well on the simulation of directional anisotropy, especially the hotspot effect. Though we find that the model overestimate the DBT with Bias of 1.2K, it can be an option as a data reference to study temporal variance of component temperatures and DBTs when field measurement is inaccessible

Process analysis of characteristics of the boundary layer during a heavy haze pollution episode in an inland megacity, China.

PubMed

Wang, Shan; Liao, Tingting; Wang, Lili; Sun, Yang

2016-02-01

Ground observation data from 8 meteorological stations in Xi'an, air mass concentration data from 13 environmental quality monitoring sites in Xi'an, as well as radiosonde observation and wind profile radar data, were used in this study. Thereby, the process, causes and boundary layer meteorological characteristics of a heavy haze episode occurring from 16 to 25 December 2013 in Xi'an were analyzed. Principal component analysis showed that this haze pollution was mainly caused by the high-intensity emission and formation of gaseous pollutants (NO2, CO and SO2) and atmospheric particles (PM2.5 (fine particles) and PM10 (respirable suspended particle). The second cause was the relative humidity and continuous low temperature. The third cause was the allocation of the surface pressure field. The presence of a near-surface temperature inversion at the boundary layer formed favorable stratification conditions for the formation and maintenance of heavy haze pollution. The persistent thick haze layer weakened the solar radiation. Meanwhile, a warming effect in the urban canopy layer and in the transition zone from the urban friction sublayer to the urban canopy was indicated. All these conditions facilitated the maintenance and reinforcement of temperature inversion. The stable atmospheric stratification finally acted on the wind field in the boundary layer, and further weakened the exchange capacity of vertical turbulence. The superposition of a wind field with the horizontal gentle wind induced the typical air stagnation and finally caused the deterioration of air quality during this haze event. Copyright © 2015. Published by Elsevier B.V.

Real-Time Characterization of Aerosol Particle Composition above the Urban Canopy in Beijing: Insights into the Interactions between the Atmospheric Boundary Layer and Aerosol Chemistry.

PubMed

Sun, Yele; Du, Wei; Wang, Qingqing; Zhang, Qi; Chen, Chen; Chen, Yong; Chen, Zhenyi; Fu, Pingqing; Wang, Zifa; Gao, Zhiqiu; Worsnop, Douglas R

2015-10-06

Despite extensive efforts into the characterization of air pollution during the past decade, real-time characterization of aerosol particle composition above the urban canopy in the megacity Beijing has never been performed to date. Here we conducted the first simultaneous real-time measurements of aerosol composition at two different heights at the same location in urban Beijing from December 19, 2013 to January 2, 2014. The nonrefractory submicron aerosol (NR-PM1) species were measured in situ by a high-resolution aerosol mass spectrometer at near-ground level and an aerosol chemical speciation monitor at 260 m on a 325 m meteorological tower in Beijing. Secondary aerosol showed similar temporal variations between ground level and 260 m, whereas much weaker correlations were found for the primary aerosol. The diurnal evolution of the ratios and correlations of aerosol species between 260 m and the ground level further illustrated a complex interaction between vertical mixing processes and local source emissions on aerosol chemistry in the atmospheric boundary layer. As a result, the aerosol compositions at the two heights were substantially different. Organic aerosol (OA), mainly composed of primary OA (62%), at the ground level showed a higher contribution to NR-PM1 (65%) than at 260 m (54%), whereas a higher concentration and contribution (15%) of nitrate was observed at 260 m, probably due to the favorable gas-particle partitioning under lower temperature conditions. In addition, two different boundary layer structures were observed, each interacting differently with the evolution processes of aerosol chemistry.

Nested high-resolution modeling of the impact of urbanization on regional climate in three vast urban agglomerations in China

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei; Hu, Yonghong; Jia, Gensuo

2012-11-01

In this paper, the Weather Research and Forecasting Model, coupled to the Urban Canopy Model, is employed to simulate the impact of urbanization on the regional climate over three vast city agglomerations in China. Based on high-resolution land use and land cover data, two scenarios are designed to represent the nonurban and current urban land use distributions. By comparing the results of two nested, high-resolution numerical experiments, the spatial and temporal changes on surface air temperature, heat stress index, surface energy budget, and precipitation due to urbanization are analyzed and quantified. Urban expansion increases the surface air temperature in urban areas by about 1°C, and this climatic forcing of urbanization on temperature is more pronounced in summer and nighttime than other seasons and daytime. The heat stress intensity, which reflects the combined effects of temperature and humidity, is enhanced by about 0.5 units in urban areas. The regional incoming solar radiation increases after urban expansion, which may be caused by the reduction of cloud fraction. The increased temperature and roughness of the urban surface lead to enhanced convergence. Meanwhile, the planetary boundary layer is deepened, and water vapor is mixed more evenly in the lower atmosphere. The deficit of water vapor leads to less convective available potential energy and more convective inhibition energy. Finally, these combined effects may reduce the rainfall amount over urban areas, mainly in summer, and change the regional precipitation pattern to a certain extent.

Application of the ACASA model for urban development studies

NASA Astrophysics Data System (ADS)

Marras, S.; Pyles, R. D.; Falk, M.; Snyder, R. L.; Paw U, K. T.; Blecic, I.; Trunfio, G. A.; Cecchini, A.; Spano, D.

2012-04-01

Since urban population is growing fast and urban areas are recognized as the major source of CO2 emissions, more attention has being dedicated to the topic of urban sustainability and its connection with the climate. Urban flows of energy, water and carbon have an important impact on climate change and their quantification is pivotal in the city design and management. Large effort has been devoted to quantitative estimates of the urban metabolism components, and several advanced models have been developed and used at different spatial and temporal scales for this purpose. However, it is necessary to develop suitable tools and indicators to effectively support urban planning and management with the goal of achieving a more sustainable metabolism in the urban environment. In this study, the multilayer model ACASA (Advanced Canopy-Atmosphere-Soil Algorithm) was chosen to simulate the exchanges of heat, water vapour and CO2 within and above urban canopy. After several calibration and evaluation tests over natural and agricultural ecosystems, the model was recently modified for application in urban and peri-urban areas. New equations to account for the anthropogenic contribution to heat exchange and carbon production, as well as key parameterizations of leaf-facet scale interactions to separate both biogenic and anthropogenic flux sources and sinks, were added to test changes in land use or urban planning strategies. The analysis was based on the evaluation of the ACASA model performance in estimating urban metabolism components at local scale. Simulated sensible heat, latent heat, and carbon fluxes were compared with in situ Eddy Covariance measurements collected in the city centre of Florence (Italy). Statistical analysis was performed to test the model accuracy and reliability. Model sensitivity to soil types and increased population density values was conducted to investigate the potential use of ACASA for evaluating the impact of planning alternative scenarios. In this contest, an in progress application of ACASA for estimating carbon exchanges alternative scenarios is represented by its integration in a software framework composed by: (i) a Cellular Automata model to simulate the urban land-use dynamics; (ii) a transportation model, able to estimate the variation of the transportation network load; (iii) the ACASA model, and (iv) the mesoscale weather model WRF for the estimation of the relevant urban metabolism components at regional scale. The CA module is able to produce future land use maps, which represent a spatial distribution of the aggregate land-use demand consistent with the main rules governing the functioning of an urban system. Such future land use maps, together with the street network including the current traffic data, are used by the transportation module for estimating future traffic data coherent with the assumed land uses trends. All these information are then used by the coupled model WRF-ACASA for estimating future maps of CO2 fluxes in the urban area under consideration, allowing to estimate the impact of future planning strategies in reducing C emissions. The in-progress application of this system to the city of Florence is presented here.

Impact of Extensive Urbanization on Summertime Rainfall in the Beijing Region and the Role of Local Precipitation Recycling

NASA Astrophysics Data System (ADS)

Wang, Jun; Feng, Jinming; Yan, Zhongwei

2018-04-01

In this study, we conducted nested high-resolution simulations using the Weather Research and Forecasting model coupled with a single-layer urban canopy model to investigate the impact of extensive urbanization on regional precipitation over the Beijing-Tianjin-Hebei region in China. The results showed that extensive urbanization decreased precipitation considerably over and downwind of Beijing city. The prevalence of impermeable urban land inhibits local evaporation that feeds moisture into the overlying atmosphere, decreasing relative humidity and atmospheric instability. The dynamic precipitation recycling model was employed to estimate the precipitation that originates from local surface evaporation and large-scale advection of moisture. Results showed that about 11% of the urbanization-induced decrease in total precipitation over the Greater Beijing Region and its surroundings was contributed by the decrease in local recycled precipitation, while the other part (89%) was due to decreasing large-scale advected precipitation. Results suggest that the low evaporation from urban land surfaces not only reduces the supply of water vapor for local recycled precipitation directly but also decreases the convective available potential energy and hence the conversion efficiency of atmospheric moisture into rainfall. The urbanization-induced variations in local recycled precipitation were found to be correlated with the net atmospheric moisture flux on a monthly time scale.

New datasets for quantifying snow-vegetation-atmosphere interactions in boreal birch and conifer forests

NASA Astrophysics Data System (ADS)

Reid, T. D.; Essery, R.; Rutter, N.; Huntley, B.; Baxter, R.; Holden, R.; King, M.; Hancock, S.; Carle, J.

2012-12-01

Boreal forests exert a strong influence on weather and climate by modifying the surface energy and radiation balance. However, global climate and numerical weather prediction models use forest parameter values from simple look-up tables or maps that are derived from limited satellite data, on large grid scales. In reality, Arctic landscapes are inherently heterogeneous, with highly variable land cover types and structures on a variety of spatial scales. There is value in collecting detailed field data for different areas of vegetation cover, to assess the accuracy of large-scale assumptions. To address these issues, a consortium of researchers funded by the UK's Natural Environment Research Council have collected extensive data on radiation, meteorology, snow cover and canopy structure at two contrasting Arctic forest sites. The chosen study sites were an area of boreal birch forest near Abisko, Sweden in March/April 2011 and mixed conifer forest at Sodankylä, Finland in March/April 2012. At both sites, arrays comprising ten shortwave pyranometers and four longwave pyrgeometers were deployed for periods of up to 50 days, under forest plots of varying canopy structures and densities. In addition, downwelling longwave irradiance and global and diffuse shortwave irradiances were recorded at nearby open sites representing the top-of-canopy conditions. Meteorological data were recorded at all sub-canopy and open sites using automatic weather stations. Over the same periods, tree skin temperatures were measured on selected trees using contact thermocouples, infrared thermocouples and thermal imagery. Canopy structure was accurately quantified through manual surveys, extensive hemispherical photography and terrestrial laser scans of every study plot. Sub-canopy snow depth and snow water equivalent were measured on fine-scale grids at each study plot. Regular site maintenance ensured a high quality dataset covering the important Arctic spring period. The data have several applications, for example in forest ecology, canopy radiative transfer models, snow hydrological modelling, and land surface schemes, for a variety of canopy types from sparse, leafless birch to dense pine and spruce. The work also allows the comparison of modern, highly detailed methods such as laser scanning and thermal imagery with older, well-established data collection methods. By combining these data with airborne and satellite remote sensing data, snow-vegetation-atmosphere interactions could be estimated over a wide area of the heterogeneous boreal landscape. This could improve estimates of crucial parameters such as land surface albedo on the grid scales required for global or regional weather and climate models.

New York City Impact on Regional Heat Wave

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz, Luis E.; Schoonen, Martin

Abstract Extreme heat events are projected to increase in magnitude and frequency throughout this century due to increasing global temperatures, making it critically important to acquire improved understanding of their genesis and interactions with large cities. This study presents an application of the factor separation method to assess combined impacts of a synoptic scale heat wave, urban land cover, and urban energy and momentum fluxes on temperatures and winds over New York City via use of high resolution simulations (1 km grid spacing) with an urbanized WRF model. Results showed that, while the heat wave had the largest contribution tomore » temperatures (> 8°C), urban surface factors matched it in highly urbanized areas. Surface factors matched this in highly urbanized areas during night and early morning hours, with contributions up to 5°C, when calm land breeze conditions result in a strong urban heat island. Positive interactions between all factors during morning and nighttime indicate urban heat island amplification of up to 4°C during the heat wave. Midtown Manhattan vertical cross-sections, where urban canopies are most dense, showed a change in the sign (from positive to negative) of the contribution of the urban fluxes between night and day below 500 m, possibly due to radiation blocking and increased thermal storage by buildings as well as frictional effects opposing the incoming warm air.« less

New York City Impact on Regional Heat Wave

DOE PAGES

Ortiz, Luis E.; Schoonen, Martin

2018-04-01

Abstract Extreme heat events are projected to increase in magnitude and frequency throughout this century due to increasing global temperatures, making it critically important to acquire improved understanding of their genesis and interactions with large cities. This study presents an application of the factor separation method to assess combined impacts of a synoptic scale heat wave, urban land cover, and urban energy and momentum fluxes on temperatures and winds over New York City via use of high resolution simulations (1 km grid spacing) with an urbanized WRF model. Results showed that, while the heat wave had the largest contribution tomore » temperatures (> 8°C), urban surface factors matched it in highly urbanized areas. Surface factors matched this in highly urbanized areas during night and early morning hours, with contributions up to 5°C, when calm land breeze conditions result in a strong urban heat island. Positive interactions between all factors during morning and nighttime indicate urban heat island amplification of up to 4°C during the heat wave. Midtown Manhattan vertical cross-sections, where urban canopies are most dense, showed a change in the sign (from positive to negative) of the contribution of the urban fluxes between night and day below 500 m, possibly due to radiation blocking and increased thermal storage by buildings as well as frictional effects opposing the incoming warm air.« less

Spatiotemporal throughfall patterns beneath an urban tree row

NASA Astrophysics Data System (ADS)

Bogeholz, P.; Van Stan, J. T., II; Hildebrandt, A.; Friesen, J.; Dibble, M.; Norman, Z.

2016-12-01

Much recent research has focused on throughfall patterns in natural forests as they can influence the heterogeneity of surface ecohydrological and biogeochemical processes. However, to the knowledge of the authors, no work has assessed how urban forest structures affect the spatiotemporal variability of throughfall water flux. Urbanization greatly alters not only a significant portion of the land surface, but canopy structure, with the most typical urban forest configuration being landscaped tree rows along streets, swales, parking lot medians, etc. This study examines throughfall spatiotemporal patterns for a landscaped tree row of Pinus elliottii (Engelm., slash pine) on Georgia Southern University's campus (southeastern, USA) using 150 individual observations per storm. Throughfall correlation lengths beneath this tree row were similar to, but appeared to be more stable across storm size than, observations in past studies on natural forests. Individual tree overlap and the planting interval also may more strongly drive throughfall patterns in tree rows. Meteorological influences beyond storm magnitude (intensity, intermittency, wind conditions, and atmospheric moisture demand) are also examined.

Microscale Obstacle Resolving Air Quality Model Evaluation with the Michelstadt Case

PubMed Central

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7. PMID:24027450

Microscale obstacle resolving air quality model evaluation with the Michelstadt case.

PubMed

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7.

IMPROVEMENT OF BUSINESS EFFICIENCY USING A MULTI-AGENT SIMULATION FOR HIGHWAY PATROL ON URBAN EXPRESSWAY

NASA Astrophysics Data System (ADS)

Okamoto, Taro; Taniguchi, Eiichi; Yamada, Tadashi

In Japan, the network of urban expressway has been expanding with the development of urban areas. However, the patrol systems in the urban expressway has not been operated on the basis of scientific evidence, but of conformity and experience. It is therefore crucial to efficiently operate such systems, not only to facilitate the rapid recovery of decreased expressway functionality, but also to acquire the income that supports the operation of privatized expressway companies. Therefore, we develop a multiagent simulation model consisting of the decision-making of four agents, including expressway company, highway patol company, road network users and road authority. These agents determines their schemes depending on their profit obtained. Results of the simulation identyfies the schemes that could offer the profits to the expressway companies in terms of the convenience of the users and the improvement of their operation.

Trends of urban surface temperature and heat island characteristics in the Mediterranean

NASA Astrophysics Data System (ADS)

Benas, Nikolaos; Chrysoulakis, Nektarios; Cartalis, Constantinos

2017-11-01

Urban air temperature studies usually focus on the urban canopy heat island phenomenon, whereby the city center experiences higher near surface air temperatures compared to its surrounding non-urban areas. The Land Surface Temperature (LST) is used instead of urban air temperature to identify the Surface Urban Heat Island (SUHI). In this study, the nighttime LST and SUHI characteristics and trends in the seventeen largest Mediterranean cities were investigated, by analyzing satellite observations for the period 2001-2012. SUHI averages and trends were based on an innovative approach of comparing urban pixels to randomly selected non-urban pixels, which carries the potential to better standardize satellite-derived SUHI estimations. A positive trend for both LST and SUHI for the majority of the examined cities was documented. Furthermore, a 0.1 °C decade-1 increase in urban LST corresponded to an increase in SUHI by about 0.04 °C decade-1. A longitudinal differentiation was found in the urban LST trends, with higher positive values appearing in the eastern Mediterranean. Examination of urban infrastructure and development factors during the same period revealed correlations with SUHI trends, which can be used to explain differences among cities. However, the majority of the cities examined show considerably increased trends in terms of the enhancement of SUHI. These findings are considered important so as to promote sustainable urbanization, as well as to support the development of heat island adaptation and mitigation plans in the Mediterranean.

Model analysis of urbanization impacts on boundary layer meteorology under hot weather conditions: a case study of Nanjing, China

NASA Astrophysics Data System (ADS)

Chen, Lei; Zhang, Meigen; Wang, Yongwei

2016-08-01

The Weather Research and Forecasting (WRF) model, configured with a single-layer urban canopy model, was employed to investigate the influence of urbanization on boundary layer meteorological parameters during a long-lasting heat wave. This study was conducted over Nanjing city, East China, from 26 July to 4 August 2010. The impacts of urban expansion and anthropogenic heat (AH) release were simulated to quantify their effects on 2-m temperature, 2-m water vapor mixing ratio, and 10-m wind speed and heat stress index. Urban sprawl increased the daily 2-m temperature in urbanized areas by around 1.6 °C and decreased the urban diurnal temperature range (DTR) by 1.24 °C. The contribution of AH release to the atmospheric warming was nearly 22 %, but AH had little influence on the DTR. The urban regional mean surface wind speed decreased by about 0.4 m s-1, and this decrease was successfully simulated from the surface to 300 m. The influence of urbanization on 2-m water vapor mixing ratio was significant over highly urbanized areas with a decrease of 1.1-1.8 g kg-1. With increased urbanization ratio, the duration of the inversion layer was about 4 h shorter, and the lower atmospheric layer was less stable. Urban heat island (UHI) intensity was significantly enhanced when synthesizing both urban sprawl and AH release and the daily mean UHI intensity increased by 0.74 °C. Urbanization increased the time under extreme heat stress (about 40 %) and worsened the living environment in urban areas.

The Effect of Urban Basic Medical Insurance on Health Service Utilisation in Shaanxi Province, China: A Comparison of Two Schemes

PubMed Central

Gao, Jianmin; Yang, Xiaowei; Yan, Ju'e; Xue, Qinxiang; Chen, Gang

2014-01-01

Background Urban population in China is mainly covered by two medical insurance schemes: the Urban Employee Basic Medical Insurance (UEBMI) for urban employees in formal sector and the Urban Resident Basic Medical Insurance (URBMI) for the left urban residents, mainly the unemployed, the elderly and children. This paper studies the effects of UEBMI and URBMI on health services utilisation in Shaanxi Province, Western China. Methods Cross-sectional data from the 4th National Health Services Survey - Shaanxi Province was studied. The propensity score matching and the coarsened exact matching methods have been used to estimate the average medical insurance effect on the insured. Results Compared to the uninsured, robust results suggest that UEBMI had significantly increased the outpatient health services utilisation in the last two weeks (p<0.10), whilst the significant effect on hospitalisation was evident in the CEM method (p<0.10). The effect of URBMI was limited in that although being insured was associated with higher health services utilisation, compared with the uninsured, none of the improvement was statistically significant (p>0.10). It was also found that compared with the uninsured, basic medical insurance enrollees were more likely to purchase inpatient treatments in lower levels of hospitals, consistent with the incentive of the benefit package design. Conclusion Basic Medical insurance schemes have shown a positive but limited effect on increasing health services utilisation in Shaanxi Province. The benefit package design of higher reimbursement rates for lower level hospitals has induced the insured to use medical services in lower level hospitals for inpatient services. PMID:24740282

The effect of urban basic medical insurance on health service utilisation in Shaanxi Province, China: a comparison of two schemes.

PubMed

Zhou, Zhongliang; Zhou, Zhiying; Gao, Jianmin; Yang, Xiaowei; Yan, Ju'e; Xue, Qinxiang; Chen, Gang

2014-01-01

Urban population in China is mainly covered by two medical insurance schemes: the Urban Employee Basic Medical Insurance (UEBMI) for urban employees in formal sector and the Urban Resident Basic Medical Insurance (URBMI) for the left urban residents, mainly the unemployed, the elderly and children. This paper studies the effects of UEBMI and URBMI on health services utilisation in Shaanxi Province, Western China. Cross-sectional data from the 4th National Health Services Survey - Shaanxi Province was studied. The propensity score matching and the coarsened exact matching methods have been used to estimate the average medical insurance effect on the insured. Compared to the uninsured, robust results suggest that UEBMI had significantly increased the outpatient health services utilisation in the last two weeks (p<0.10), whilst the significant effect on hospitalisation was evident in the CEM method (p<0.10). The effect of URBMI was limited in that although being insured was associated with higher health services utilisation, compared with the uninsured, none of the improvement was statistically significant (p>0.10). It was also found that compared with the uninsured, basic medical insurance enrollees were more likely to purchase inpatient treatments in lower levels of hospitals, consistent with the incentive of the benefit package design. Basic Medical insurance schemes have shown a positive but limited effect on increasing health services utilisation in Shaanxi Province. The benefit package design of higher reimbursement rates for lower level hospitals has induced the insured to use medical services in lower level hospitals for inpatient services.

Control Scheme of River-lake System from the View of Ecological Sponge Basin aiming at Sponge City Construction

NASA Astrophysics Data System (ADS)

Ding, X.; Liu, J.; Yang, Z.

2017-12-01

China is in the rapid advance of urbanization, and is promoting the Sponge City Construction (SCC) with the characteristics of natural accumulation, natural infiltration and natural purification. The Chinese government selected 16 and 14 cities as pilot cities in 2015 and 2016 respectively to carry out SCC taking Low Impact Development (LID) as the concept. However, in 2015 and 2016, water-logging occurred in 10 cities and 9 cities respectively during the pilot cities. Therefore, relying solely on LID can not solve the problem of urban flood and waterlogging. Except for a series of LID measures during the process of SCC, corresponding control scheme of river-lake system should be established to realize water-related targets. From the view of ecological sponge basin, this study presents the general idea of SCC both in and out of the unban built-up area and the corresponding control scheme of river-lake system: for the regions outside the built-up area, the main aim of SCC is to carry out the top-level design of urban flood control and waterlogging, establish the water security system outside the city for solving the problems including flood control, water resources, water environment and water ecology; for the built-up area, the main aim of SCC is to construct different kinds of urban sponge according to local conditions and develop multi-scale drainage system responding to different intensities of rainfall taking the river-lake system as the core. Taking Fenghuang County of Hunan Province as an example for the application research, the results indicate that, after the implementation of the control scheme of river-lake system: 1) together with other SCC measures including LID, the control rate of total annual runoff in Fenghuang County is expected to be 82.9% which meets the target requirement of 80%; 2) flood control and drainage standards in Fenghuang County can be increased from the current 10-year return to 20-year return; 3) urban and rural water supply guarantee rate is expected to be 98% which meets the target requirement of 95%. Therefore, the control scheme of urban river-lake system in the county is technically feasible, and can effectively solve the problems including flood control, water resources shortage and ecological water demand in the county, thus may provide strong support and guarantee for SCC.

Differences exist across insurance schemes in China post-consolidation.

PubMed

Li, Yang; Zhao, Yinjun; Yi, Danhui; Wang, Xiaojun; Jiang, Yan; Wang, Yu; Liu, Xinchun; Ma, Shuangge

2017-01-01

In China, the basic insurance system consists of three schemes: the UEBMI (Urban Employee Basic Medical Insurance), URBMI (Urban Resident Basic Medical Insurance), and NCMS (New Cooperative Medical Scheme), across which significant differences have been observed. Since 2009, the central government has been experimenting with consolidating these schemes in selected areas. This study examines whether differences still exist across schemes after the consolidation. A survey was conducted in the city of Suzhou, collecting data on subjects 45 years old and above with at least one inpatient or outpatient treatment during a period of twelve months. Analysis on 583 subjects was performed comparing subjects' characteristics across insurance schemes. A resampling-based method was applied to compute the predicted gross medical cost, OOP (out-of-pocket) cost, and insurance reimbursement rate. Subjects under different insurance schemes differ in multiple aspects. For inpatient treatments, subjects under the URBMI have the highest observed and predicted gross and OOP costs, while those under the UEBMI have the lowest. For outpatient treatments, subjects under the UEBMI and URBMI have comparable costs, while those under the NCMS have much lower costs. Subjects under the NCMS also have a much lower reimbursement rate. Differences still exist across schemes in medical costs and insurance reimbursement rate post-consolidation. Further investigations are needed to identify the causes, and interventions are needed to eliminate such differences.

Differences exist across insurance schemes in China post-consolidation

PubMed Central

Yi, Danhui; Wang, Xiaojun; Jiang, Yan; Wang, Yu; Liu, Xinchun

2017-01-01

Background In China, the basic insurance system consists of three schemes: the UEBMI (Urban Employee Basic Medical Insurance), URBMI (Urban Resident Basic Medical Insurance), and NCMS (New Cooperative Medical Scheme), across which significant differences have been observed. Since 2009, the central government has been experimenting with consolidating these schemes in selected areas. This study examines whether differences still exist across schemes after the consolidation. Methods A survey was conducted in the city of Suzhou, collecting data on subjects 45 years old and above with at least one inpatient or outpatient treatment during a period of twelve months. Analysis on 583 subjects was performed comparing subjects’ characteristics across insurance schemes. A resampling-based method was applied to compute the predicted gross medical cost, OOP (out-of-pocket) cost, and insurance reimbursement rate. Results Subjects under different insurance schemes differ in multiple aspects. For inpatient treatments, subjects under the URBMI have the highest observed and predicted gross and OOP costs, while those under the UEBMI have the lowest. For outpatient treatments, subjects under the UEBMI and URBMI have comparable costs, while those under the NCMS have much lower costs. Subjects under the NCMS also have a much lower reimbursement rate. Conclusions Differences still exist across schemes in medical costs and insurance reimbursement rate post-consolidation. Further investigations are needed to identify the causes, and interventions are needed to eliminate such differences. PMID:29125837

Optimized spectroscopic scheme for enhanced precision CO measurements with applications to urban source attribution

NASA Astrophysics Data System (ADS)

Nottrott, A.; Hoffnagle, J.; Farinas, A.; Rella, C.

2014-12-01

Carbon monoxide (CO) is an urban pollutant generated by internal combustion engines which contributes to the formation of ground level ozone (smog). CO is also an excellent tracer for emissions from mobile combustion sources. In this work we present an optimized spectroscopic sampling scheme that enables enhanced precision CO measurements. The scheme was implemented on the Picarro G2401 Cavity Ring-Down Spectroscopy (CRDS) analyzer which measures CO2, CO, CH4 and H2O at 0.2 Hz. The optimized scheme improved the raw precision of CO measurements by 40% from 5 ppb to 3 ppb. Correlations of measured CO2, CO, CH4 and H2O from an urban tower were partitioned by wind direction and combined with a concentration footprint model for source attribution. The application of a concentration footprint for source attribution has several advantages. The upwind extent of the concentration footprint for a given sensor is much larger than the flux footprint. Measurements of mean concentration at the sensor location can be used to estimate source strength from a concentration footprint, while measurements of the vertical concentration flux are necessary to determine source strength from the flux footprint. Direct measurement of vertical concentration flux requires high frequency temporal sampling and increases the cost and complexity of the measurement system.

Tree Productivity Enhanced with Conversion from Forest to Urban Land Covers.

PubMed

Briber, Brittain M; Hutyra, Lucy R; Reinmann, Andrew B; Raciti, Steve M; Dearborn, Victoria K; Holden, Christopher E; Dunn, Allison L

2015-01-01

Urban areas are expanding, changing the structure and productivity of landscapes. While some urban areas have been shown to hold substantial biomass, the productivity of these systems is largely unknown. We assessed how conversion from forest to urban land uses affected both biomass structure and productivity across eastern Massachusetts. We found that urban land uses held less than half the biomass of adjacent forest expanses with a plot level mean biomass density of 33.5 ± 8.0 Mg C ha(-1). As the intensity of urban development increased, the canopy cover, stem density, and biomass decreased. Analysis of Quercus rubra tree cores showed that tree-level basal area increment nearly doubled following development, increasing from 17.1 ± 3.0 to 35.8 ± 4.7 cm(2) yr(-1). Scaling the observed stem densities and growth rates within developed areas suggests an aboveground biomass growth rate of 1.8 ± 0.4 Mg C ha(-1) yr(-1), a growth rate comparable to nearby, intact forests. The contrasting high growth rates and lower biomass pools within urban areas suggest a highly dynamic ecosystem with rapid turnover. As global urban extent continues to grow, cities consider climate mitigation options, and as the verification of net greenhouse gas emissions emerges as critical for policy, quantifying the role of urban vegetation in regional-to-global carbon budgets will become ever more important.

Tree Productivity Enhanced with Conversion from Forest to Urban Land Covers

PubMed Central

Briber, Brittain M.; Hutyra, Lucy R.; Reinmann, Andrew B.; Raciti, Steve M.; Dearborn, Victoria K.; Holden, Christopher E.; Dunn, Allison L.

2015-01-01

Urban areas are expanding, changing the structure and productivity of landscapes. While some urban areas have been shown to hold substantial biomass, the productivity of these systems is largely unknown. We assessed how conversion from forest to urban land uses affected both biomass structure and productivity across eastern Massachusetts. We found that urban land uses held less than half the biomass of adjacent forest expanses with a plot level mean biomass density of 33.5 ± 8.0 Mg C ha-1. As the intensity of urban development increased, the canopy cover, stem density, and biomass decreased. Analysis of Quercus rubra tree cores showed that tree-level basal area increment nearly doubled following development, increasing from 17.1 ± 3.0 to 35.8 ± 4.7 cm2 yr-1. Scaling the observed stem densities and growth rates within developed areas suggests an aboveground biomass growth rate of 1.8 ± 0.4 Mg C ha-1 yr-1, a growth rate comparable to nearby, intact forests. The contrasting high growth rates and lower biomass pools within urban areas suggest a highly dynamic ecosystem with rapid turnover. As global urban extent continues to grow, cities consider climate mitigation options, and as the verification of net greenhouse gas emissions emerges as critical for policy, quantifying the role of urban vegetation in regional-to-global carbon budgets will become ever more important. PMID:26302444

Volumetric visualization of multiple-return LIDAR data: Using voxels

USGS Publications Warehouse

Stoker, Jason M.

2009-01-01

Elevation data are an important component in the visualization and analysis of geographic information. The creation and display of 3D models representing bare earth, vegetation, and surface structures have become a major focus of light detection and ranging (lidar) remote sensing research in the past few years. Lidar is an active sensor that records the distance, or range, of a laser usually fi red from an airplane, helicopter, or satellite. By converting the millions of 3D lidar returns from a system into bare ground, vegetation, or structural elevation information, extremely accurate, high-resolution elevation models can be derived and produced to visualize and quantify scenes in three dimensions. These data can be used to produce high-resolution bare-earth digital elevation models; quantitative estimates of vegetative features such as canopy height, canopy closure, and biomass; and models of urban areas such as building footprints and 3D city models.

Multiple health benefits of urban tree canopy: The mounting evidence for a green prescription.

PubMed

Ulmer, Jared M; Wolf, Kathleen L; Backman, Desiree R; Tretheway, Raymond L; Blain, Cynthia Ja; O'Neil-Dunne, Jarlath Pm; Frank, Lawrence D

2016-11-01

The purpose of this study was to enhance the understanding of the health-promoting potential of trees in an urbanized region of the United States. This was done using high-resolution LiDAR and imagery data to quantify tree cover within 250m of the residence of 7910 adult participants in the California Health Interview Survey, then testing for main and mediating associations between tree cover and multiple health measures. The results indicated that more neighborhood tree cover, independent from green space access, was related to better overall health, primarily mediated by lower overweight/obesity and better social cohesion, and to a lesser extent by less type 2 diabetes, high blood pressure, and asthma. These findings suggest an important role for trees and nature in improving holistic population health in urban areas. Copyright © 2016 Elsevier Ltd. All rights reserved.

Turbulence and Air Exchange in a Two-Dimensional Urban Street Canyon Between Gable Roof Buildings

NASA Astrophysics Data System (ADS)

Garau, Michela; Badas, Maria Grazia; Ferrari, Simone; Seoni, Alessandro; Querzoli, Giorgio

2018-04-01

We experimentally investigate the effect of a typical building covering: the gable roof, on the flow and air exchange in urban canyons. In general, the morphology of the urban canopy is very varied and complex, depending on a large number of factors, such as building arrangement, or the morphology of the terrain. Therefore we focus on a simple, prototypal shape, the two-dimensional canyon, with the aim of elucidating some fundamental phenomena driving the street-canyon ventilation. Experiments are performed in a water channel, over an array of identical prismatic obstacles representing an idealized urban canopy. The aspect ratio, i.e. canyon-width to building-height ratio, ranges from 1 to 6. Gable roof buildings with 1:1 pitch are compared with flat roofed buildings. Velocity is measured using a particle-image-velocimetry technique with flow dynamics discussed in terms of mean flow and second- and third-order statistical moments of the velocity. The ventilation is interpreted by means of a simple well-mixed box model and the outflow rate and mean residence time are computed. Results show that gable roofs tend to delay the transition from the skimming-flow to the wake-interference regime and promote the development of a deeper and more turbulent roughness layer. The presence of a gable roof significantly increases the momentum flux, especially for high packing density. The air exchange is improved compared to the flat roof buildings, and the beneficial effect is more significant for narrow canyons. Accordingly, for unit aspect ratio gable roofs reduce the mean residence time by a factor of 0.37 compared to flat roofs, whereas the decrease is only by a factor of 0.9 at the largest aspect ratio. Data analysis indicates that, for flat roof buildings, the mean residence time increases by 30% when the aspect ratio is decreased from 6 to 2, whereas this parameter is only weakly dependent on aspect ratio in the case of gable roofs.

Mapping urban forest tree species using IKONOS imagery: preliminary results.

PubMed

Pu, Ruiliang

2011-01-01

A stepwise masking system with high-resolution IKONOS imagery was developed to identify and map urban forest tree species/groups in the City of Tampa, Florida, USA. The eight species/groups consist of sand live oak (Quercus geminata), laurel oak (Quercus laurifolia), live oak (Quercus virginiana), magnolia (Magnolia grandiflora), pine (species group), palm (species group), camphor (Cinnamomum camphora), and red maple (Acer rubrum). The system was implemented with soil-adjusted vegetation index (SAVI) threshold, textural information after running a low-pass filter, and brightness threshold of NIR band to separate tree canopies from non-vegetated areas from other vegetation types (e.g., grass/lawn) and to separate the tree canopies into sunlit and shadow areas. A maximum likelihood classifier was used to identify and map forest type and species. After IKONOS imagery was preprocessed, a total of nine spectral features were generated, including four spectral bands, three hue-intensity-saturation indices, one SAVI, and one texture image. The identified and mapped results were examined with independent ground survey data. The experimental results indicate that when classifying all the eight tree species/ groups with the high-resolution IKONOS image data, the identifying accuracy was very low and could not satisfy a practical application level, and when merging the eight species/groups into four major species/groups, the average accuracy is still low (average accuracy = 73%, overall accuracy = 86%, and κ = 0.76 with sunlit test samples). Such a low accuracy of identifying and mapping the urban tree species/groups is attributable to low spatial resolution IKONOS image data relative to tree crown size, to complex and variable background spectrum impact on crown spectra, and to shadow/shaded impact. The preliminary results imply that to improve the tree species identification accuracy and achieve a practical application level in urban area, multi-temporal (multi-seasonal) or hyperspectral data image data should be considered for use in the future.

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

Where the woodland ends: How edges affect landscape structure and physiological responses of Quercus agrifolia

NASA Astrophysics Data System (ADS)

de Chant, Timothy Paul

Forests and woodlands are integral parts of ecosystems across the globe, but they are threatened by a variety of factors, including urbanization and introduced forest pathogens. These two forces are fundamentally altering ecosystems, both by removing forest cover and reshaping landscapes. Comprehending how these two processes have changed forest ecosystems is an important step toward understanding how the affected systems will function in the future. I investigated the range of edge effects that result from disturbance brought about by forest pathogens and urbanization in two coastal oak woodlands in Marin County, California. Oak woodlands are a dynamic part of California's landscape, reacting to changes in their biotic and abiotic environments across a range of spatial and temporal scales. Sudden Oak Death, caused by the introduced forest pathogen Phytophthora ramorum, has led to widespread mortality of many tree species in California's oak woodlands. I investigated how the remaining trees respond to such rapid changes in canopy structure (Chapter 2), and my results revealed a forest canopy quick to respond to the new openings. Urbanization, another disturbance regime, operates on a longer time scale. Immediately following urban development, forest edges are strikingly linear, but both forest processes and homeowner actions likely work in concert to disrupt the straight edge (Chapter 3). Forest edges grew more sinuous within 14 years of the initial disturbance, and continued to do so for the remainder of the study, another 21 years. Individual Quercus agrifolia trees also respond to urban edges decades after disturbance (Chapter 4), and their reaction is reflected in declining stable carbon isotope values (delta13C). This change suggests trees may have increased their stomatal conductance in response to greater water availability, reduced their photosynthetic rate as a result of stress, or some combination of both. Edges have far reaching and long lasting effects on forest structure and function. Investigations of their impacts on multiple spatial and temporal scales are important in determining the range of effects they have on forest ecosystems. Studies that combine remote sensing, geographic information systems, and field studies may help us understand the ecological consequences of forest edges.

Impact of Land Cover Characterization and Properties on Snow Albedo in Climate Models

NASA Astrophysics Data System (ADS)

Wang, L.; Bartlett, P. A.; Chan, E.; Montesano, P.

2017-12-01

The simulation of winter albedo in boreal and northern environments has been a particular challenge for land surface modellers. Assessments of output from CMIP3 and CMIP5 climate models have revealed that many simulations are characterized by overestimation of albedo in the boreal forest. Recent studies suggest that inaccurate representation of vegetation distribution, improper simulation of leaf area index, and poor treatment of canopy-snow processes are the primary causes of albedo errors. While several land cover datasets are commonly used to derive plant functional types (PFT) for use in climate models, new land cover and vegetation datasets with higher spatial resolution have become available in recent years. In this study, we compare the spatial distribution of the dominant PFTs and canopy cover fractions based on different land cover datasets, and present results from offline simulations of the latest version Canadian Land Surface Scheme (CLASS) over the northern Hemisphere land. We discuss the impact of land cover representation and surface properties on winter albedo simulations in climate models.

Assessing Structure and Condition of Temperate And Tropical Forests: Fusion of Terrestrial Lidar and Airborne Multi-Angle and Lidar Remote Sensing

NASA Astrophysics Data System (ADS)

Saenz, Edward J.

Forests provide vital ecosystem functions and services that maintain the integrity of our natural and human environment. Understanding the structural components of forests (extent, tree density, heights of multi-story canopies, biomass, etc.) provides necessary information to preserve ecosystem services. Increasingly, remote sensing resources have been used to map and monitor forests globally. However, traditional satellite and airborne multi-angle imagery only provide information about the top of the canopy and little about the forest structure and understory. In this research, we investigative the use of rapidly evolving lidar technology, and how the fusion of aerial and terrestrial lidar data can be utilized to better characterize forest stand information. We further apply a novel terrestrial lidar methodology to characterize a Hemlock Woolly Adelgid infestation in Harvard Forest, Massachusetts, and adapt a dynamic terrestrial lidar sampling scheme to identify key structural vegetation profiles of tropical rainforests in La Selva, Costa Rica.

Characteristics of urban natural areas influencing winter bird use in southern Ontario, Canada.

PubMed

Smith, Paul G R

2007-03-01

Characteristics of urban natural areas and surrounding landscapes were identified that best explain winter bird use for 28 urban natural areas in southern Ontario, Canada. The research confirms for winter birds the importance of area (size) and natural vegetation, rather than managed, horticultural parkland, within urban natural areas as well as percent urban land use and natural habitat in surrounding landscapes. Alien bird density and percent ground feeding species increased with percent surrounding urban land use. Higher percent forest cover was associated with higher percentages of forest, bark feeding, small (<20 g) and insectivorous species. Natural area size (ha) was related to higher species richness, lower evenness and higher percentages of insectivorous, forest interior, area-sensitive, upper canopy, bark feeding, and non-resident species. Higher number of habitat types within natural areas and percent natural habitat in surrounding landscapes were also associated with higher species richness. Common, resident bird species dominated small areas (<6.5 ha), while less common non-residents increased with area, indicative of a nested distribution. Areas at least 6.5 ha and more generally >20 ha start to support some area-sensitive species. Areas similar to rural forests had >25% insectivores, >25% forest interior species, >25% small species, and <5% alien species. Indicator species separated urban natural areas from rural habitats and ordination placed urban natural areas along a gradient between urban development and undisturbed, rural forests. More attention is needed on issues of winter bird conservation in urban landscapes.

Characteristics of Urban Natural Areas Influencing Winter Bird Use in Southern Ontario, Canada

NASA Astrophysics Data System (ADS)

Smith, Paul G. R.

2007-03-01

Characteristics of urban natural areas and surrounding landscapes were identified that best explain winter bird use for 28 urban natural areas in southern Ontario, Canada. The research confirms for winter birds the importance of area (size) and natural vegetation, rather than managed, horticultural parkland, within urban natural areas as well as percent urban land use and natural habitat in surrounding landscapes. Alien bird density and percent ground feeding species increased with percent surrounding urban land use. Higher percent forest cover was associated with higher percentages of forest, bark feeding, small (<20 g) and insectivorous species. Natural area size (ha) was related to higher species richness, lower evenness and higher percentages of insectivorous, forest interior, area-sensitive, upper canopy, bark feeding, and non-resident species. Higher number of habitat types within natural areas and percent natural habitat in surrounding landscapes were also associated with higher species richness. Common, resident bird species dominated small areas (<6.5 ha), while less common non-residents increased with area, indicative of a nested distribution. Areas at least 6.5 ha and more generally >20 ha start to support some area-sensitive species. Areas similar to rural forests had >25% insectivores, >25% forest interior species, >25% small species, and <5% alien species. Indicator species separated urban natural areas from rural habitats and ordination placed urban natural areas along a gradient between urban development and undisturbed, rural forests. More attention is needed on issues of winter bird conservation in urban landscapes.

Impact of isoprene and nitrogen oxides on O3 chemistry at the local and the regional scale : the ESCOMPTE experiment

NASA Astrophysics Data System (ADS)

Cortinovis, J.; Solmon, F.; Personne, E.; Serça, D.; Rosset, R.

2003-04-01

Concentrations of nitrogen oxides (NOx = NO+NO2) and volatile organic compounds (VOCs) play a crucial role in the atmospheric chemistry through the production-destruction of tropospheric O3. In rural areas, NOx concentrations are much lower than in urban areas, whereas VOCs emissions can be relatively high. This is due to a relative longer residence time of VOCs, and to the substantial contribution of Biogenic VOCs (BVOCs) representing more than 85% of all the VOCs emitted at the Earth surface (half of it being isoprene). For these reasons, O3 production in rural areas is most of the time NOx-limited. Taking into account biogenic emissions of isoprene in global scale atmospheric chemistry modeling adds from 10 to 40% to the ozone produced when compared to the same simulation without isoprene. This suggests that BVOCs and NOx emissions must be accounted for in models of atmospheric pollution forecasting at local and regional scales. In this study, we present a sensitivity analysis on the impact of the isoprene and nitrogen oxides emissions at the local and the regional scale. This study is done from data collected during the ESCOMPTE campaign which took place in June and July 2001 in the Marseille region (Southwest France) characterized by both strong natural and anthropogenic sources of trace gases. Isoprene emission experimental data from a Quercus Pubescens Mediterranean forest are used to constrain the 1Dz Soil-Vegetation-Atmospheric-Transfer ISBA model. This SVAT is used in the 3D MESO-NH-Chemistry model to simulate scenarios of pollution at the regional scale including the measured biogenic source for isoprene, and GENEMIS anthropogenic sources for other trace gases. To focus on the chemistry aspect of these simulations, the atmospheric dynamics are set to an "ideal" configuration. We have investigated the impact of the relative position and distance between the biogenic and anthropogenic sources on the O3 budget. According to this, and to the intensity of the anthropogenic sources, isoprene emissions impact can become relatively significant in terms of O3 concentrations. O3 production is clearly linked with the different photochemical regime, with limitations for high COV:NOx (>20 -NOx limited) and low (<4 -COV limited) ratios. We performed an other sensitivity analysis on biogenic NOx emissions from crops, and their impact on O3 budget using a 1Dz model SURFATM. This model is based on an approach describing atmospheric exchanges with resistances (Choudhury and Monteith, 1988 ; Nemitz, 1998). Similarly to the ISBA scheme, SURFATM simulates the surface energy budget and the atmosphere-biosphere exchange of chemical species. We developed the model by including the basic NOx-O3 chemistry above and below the canopy. Ozone fluxes were simulated by the model constrained with ESCOMPTE experimental data performed in a maize field. The more detailed description of vegetation, and the inclusion of the chemistry scheme allowed us to have a better representation of ozone fluxes at the canopy scale. SURFATM will then be used in MESO-NH-Chemistry to simulate the interaction between a rural and an urban (or industrial) plume, as we did for isoprene. The last step will be to include the biogenic sources for isoprene and nitrogen oxides, and to perform new scenarios of pollution at the local or regional scale.

Effects of urban tree canopy loss on land surface temperature magnitude and timing

NASA Astrophysics Data System (ADS)

Elmes, Arthur; Rogan, John; Williams, Christopher; Ratick, Samuel; Nowak, David; Martin, Deborah

2017-06-01

Urban Tree Canopy (UTC) plays an important role in moderating the Surface Urban Heat Island (SUHI) effect, which poses threats to human health due to substantially increased temperatures relative to rural areas. UTC coverage is associated with reduced urban temperatures, and therefore benefits both human health and reducing energy use in cities. Measurement of this relationship relies on accurate, fine spatial resolution UTC mapping, and on time series analysis of Land Surface Temperatures (LST). The City of Worcester, Massachusetts underwent extensive UTC loss and gain during the relatively brief period from 2008 to 2015, providing a natural experiment to measure the UTC/LST relationship. This paper consists of two elements to this end. First, it presents methods to map UTC in urban and suburban locations at fine spatial resolution (∼0.5 m) using image segmentation of a fused Lidar/WorldView-2 dataset, in order to show UTC change over time. Second, the areas of UTC change are used to explore changes in LST magnitude and seasonal variability using a time series of all available Landsat data for the study area over the eight-year period from 2007 to 2015. Fractional UTC change per unit area was determined using fine resolution UTC maps for 2008, 2010, and 2015, covering the period of large-scale tree loss and subsequent planting. LST changes were measured across a series of net UTC change bins, providing a relationship between UTC net change and LST trend. LST was analyzed for both monotonic trends over time and changes to seasonal magnitude and timing, using Theil-Sen slopes and Seasonal Trend Analysis (STA), respectively. The largest magnitudes of UTC loss occurred in residential neighborhoods, causing increased exposure of impervious (road) and pervious (grass) surfaces. Net UTC loss showed higher monotonic increases in LST than persistence and gain areas. STA indicated that net UTC loss was associated greater difference between 2008 and 2015 seasonal temperature curves than persistence areas, and also larger peak LST values, with peak increases ranging from 1 to 6 °C. Timing of summer warm period was extended in UTC loss areas by up to 15 days. UTC gain provided moderate LST mitigation, with lower monotonic trends, lower peak temperatures, and smaller seasonal curve changes than both persistence and loss locations. This study shows that urban trees mitigate the magnitude and timing of the surface urban heat island effect, even in suburban areas with less proportional impervious coverage than the dense urban areas traditionally associated with SUHI. Trees can therefore be seen as an effective means of offsetting the energy-intensive urban heat island effect.

Evaluation of the WRF-Urban Modeling System Coupled to Noah and Noah-MP Land Surface Models Over a Semiarid Urban Environment

NASA Astrophysics Data System (ADS)

Salamanca, Francisco; Zhang, Yizhou; Barlage, Michael; Chen, Fei; Mahalov, Alex; Miao, Shiguang

2018-03-01

We have augmented the existing capabilities of the integrated Weather Research and Forecasting (WRF)-urban modeling system by coupling three urban canopy models (UCMs) available in the WRF model with the new community Noah with multiparameterization options (Noah-MP) land surface model (LSM). The WRF-urban modeling system's performance has been evaluated by conducting six numerical experiments at high spatial resolution (1 km horizontal grid spacing) during a 15 day clear-sky summertime period for a semiarid urban environment. To assess the relative importance of representing urban surfaces, three different urban parameterizations are used with the Noah and Noah-MP LSMs, respectively, over the two major cities of Arizona: Phoenix and Tucson metropolitan areas. Our results demonstrate that Noah-MP reproduces somewhat better than Noah the daily evolution of surface skin temperature and near-surface air temperature (especially nighttime temperature) and wind speed. Concerning the urban areas, bulk urban parameterization overestimates nighttime 2 m air temperature compared to the single-layer and multilayer UCMs that reproduce more accurately the daily evolution of near-surface air temperature. Regarding near-surface wind speed, only the multilayer UCM was able to reproduce realistically the daily evolution of wind speed, although maximum winds were slightly overestimated, while both the single-layer and bulk urban parameterizations overestimated wind speed considerably. Based on these results, this paper demonstrates that the new community Noah-MP LSM coupled to an UCM is a promising physics-based predictive modeling tool for urban applications.

Reducing the uncertainty in the projection of the terrestrial carbon cycle by fusing models with remote sensing data

NASA Astrophysics Data System (ADS)

Serbin, S.; Shiklomanov, A. N.; Viskari, T.; Desai, A. R.; Townsend, P. A.; Dietze, M.

2015-12-01

Modeling global change requires accurate representation of terrestrial carbon (C), energy and water fluxes. In particular, capturing the properties of vegetation canopies that describe the radiation regime are a key focus for global change research because the properties related to radiation utilization and penetration within plant canopies provide an important constraint on terrestrial ecosystem productivity, as well as the fluxes of water and energy from vegetation to the atmosphere. As such, optical remote sensing observations present an important, and as yet relatively untapped, source of observations that can be used to inform modeling activities. In particular, high-spectral resolution optical data at the leaf and canopy scales offers the potential for an important and direct data constraint on the parameterization and structure of the radiative transfer model (RTM) scheme within ecosystem models across diverse vegetation types, disturbance and management histories. In this presentation we highlight ongoing work to integrate optical remote sensing observations, specifically leaf and imaging spectroscopy (IS) data across a range of forest ecosystems, into complex ecosystem process models within an efficient computational assimilation framework as a means to improve the description of canopy optical properties, vegetation composition, and modeled radiation balance. Our work leverages the Predictive Ecosystem Analyzer (PEcAn; http://www.pecanproject.org/) ecoinformatics toolbox together with a RTM module designed for efficient assimilation of leaf and IS observations to inform vegetation optical properties as well as associated plant traits. Ultimately, an improved understanding of the radiation balance of ecosystems will provide a better constraint on model projections of energy balance, vegetation composition, and carbon pools and fluxes thus allowing for a better diagnosis of the vulnerability of terrestrial ecosystems in response to global change.

The influence of vegetation on the horizontal and vertical distribution of pollutants in a street canyon.

PubMed

Salmond, J A; Williams, D E; Laing, G; Kingham, S; Dirks, K; Longley, I; Henshaw, G S

2013-01-15

Space constraints in cities mean that there are only limited opportunities for increasing tree density within existing urban fabric and it is unclear whether the net effect of increased vegetation in street canyons is beneficial or detrimental to urban air quality at local scales. This paper presents data from a field study undertaken in Auckland, New Zealand designed to determine the local impact of a deciduous tree canopy on the distribution of the oxides of nitrogen within a street canyon. The results showed that the presence of leaves on the trees had a marked impact on the transport of pollutants and led to a net accumulation of pollutants in the canyon below the tree tops. The incidence and magnitude of temporally localised spikes in pollutant concentration were reduced within the tree canopy itself. A significant difference in pollutant concentrations with height was not observed when leaves were absent. Analysis of the trends in concentration associated with different wind directions showed a smaller difference between windward and leeward sides when leaves were on the trees. A small relative increase in concentrations on the leeward side was observed during leaf-on relative to leaf-off conditions as predicted by previous modelling studies. However the expected reduction in concentrations on the windward side was not observed. The results suggest that the presence of leaves on the trees reduces the upwards transport of fresh vehicle emissions, increases the storage of pollutants within the canopy space and reduces the penetration of clean air downwards from aloft. Differences observed between NO and NO(2) concentrations could not be accounted for by dispersion processes alone, suggesting that there may also be some changes in the chemistry of the atmosphere associated with the presence of leaves on the trees. Copyright © 2012 Elsevier B.V. All rights reserved.

Attribution and Characterisation of Sclerophyll Forested Landscapes Over Large Areas

NASA Astrophysics Data System (ADS)

Jones, Simon; Soto-Berelov, Mariela; Suarez, Lola; Wilkes, Phil; Woodgate, Will; Haywood, Andrew

2016-06-01

This paper presents a methodology for the attribution and characterisation of Sclerophyll forested landscapes over large areas. First we define a set of woody vegetation data primitives (e.g. canopy cover, leaf area index (LAI), bole density, canopy height), which are then scaled-up using multiple remote sensing data sources to characterise and extract landscape woody vegetation features. The advantage of this approach is that vegetation landscape features can be described from composites of these data primitives. The proposed data primitives act as building blocks for the re-creation of past woody characterisation schemes as well as allowing for re-compilation to support present and future policy and management and decision making needs. Three main research sites were attributed; representative of different sclerophyll woody vegetated systems (Box Iron-bark forest; Mountain Ash forest; Mixed Species foothills forest). High resolution hyperspectral and full waveform LiDAR data was acquired over the three research sites. At the same time, land management agencies (Victorian Department of Environment, Land Water and Planning) and researchers (RMIT, CRC for Spatial Information and CSIRO) conducted fieldwork to collect structural and functional measurements of vegetation, using traditional forest mensuration transects and plots, terrestrial lidar scanning and high temporal resolution in-situ autonomous laser (VegNet) scanners. Results are presented of: 1) inter-comparisons of LAI estimations made using ground based hemispherical photography, LAI 2200 PCA, CI-110 and terrestrial and airborne laser scanners; 2) canopy height and vertical canopy complexity derived from airborne LiDAR validated using ground observations; and, 3) time-series characterisation of land cover features. 1. Accuracy targets for remotely sensed LAI products to match within ground based estimates are ± 0.5 LAI or a 20% maximum (CEOS/GCOS) with new aspirational targets of 5%). In this research we conducted a total of 67 ground-based method-to-method pairwise comparisons across 11 plots in five sites, incorporating the previously mentioned LAI methods. Out of the 67 comparisons, 29 had an RMSE ≥ 0.5 LAIe. This has important implications for the validation of remotely sensed products since ground based techniques themselves exhibit LAI variations greater than internationally recommended guidelines for satellite product accuracies. 2. Two methods of canopy height derivation are proposed and tested over a large area (4 Million Ha). 99th percentile maximum height achieved a RMSE of 6.6%, whilst 95th percentile dominant height a RMSE = 10.3%. Vertical canopy complexity (i.e. the number of forest layers of strata) was calculated as the local maxima of vegetation density within the LiDAR canopy profile and determined using a cubic spline smoothing of Pgap. This was then validated against in-situ and LiDAR observations of canopy strata with an RMSE 0.39 canopy layers. 3. Preliminary results are presented of landcover characterisation using LandTrendr analysis of Landsat LEDAPS data. kNN is then used to link these features to a dense network of 800 field plots sites.

Improving energy partitioning and the nighttime energy balance by implementation of a multi-layer energy budget in ORCHIDEE-CAN

NASA Astrophysics Data System (ADS)

Chen, Yiying; Ryder, James; Naudts, Kim; McGrath, Matthew J.; Otto, Juliane; Bastriko, Vladislav; Valade, Aude; Launiainen, Samuli; Ogée, Jérôme; Elbers, Jan A.; Foken, Thomas; Tiedemann, Frank; Heinesch, Bernard; Black, Andrew; Haverd, Vanessa; Loustau, Denis; Ottlé, Catherine; Peylin, Philippe; Polcher, Jan; Luyssaert, Sebastiaan

2015-04-01

Canopy structure is one of the most important vegetation characteristics for land-atmosphere interactions as it determines the energy and scalar exchanges between land surface and overlay air mass. In this study we evaluated the performance of a newly developed multi-layer energy budget (Ryder et al., 2014) in a land surface model, ORCHIDEE-CAN (Naudts et al., 2014), which simulates canopy structure and can be coupled to an atmospheric model using an implicit procedure. Furthermore, a vertical discrete drag parametrization scheme was also incorporated into this model, in order to obtain a better description of the sub-canopy wind profile simulation. Site level datasets, including the top-of-the-canopy and sub-canopy observations made available from eight flux observation sites, were collected in order to conduct this evaluation. The geo-location of the collected observation sites crossed climate zones from temperate to boreal and the vegetation types included deciduous, evergreen broad leaved and evergreen needle leaved forest with maximum LAI ranging from 2.1 to 7.0. First, we used long-term top-of-the-canopy measurements to analyze the performance of the current one-layer energy budget in ORCHIDEE-CAN. Three major processes were identified for improvement through the implementation of a multi-layer energy budget: 1) night time radiation balance, 2) energy partitioning during winter and 3) prediction of the ground heat flux. Short-term sub-canopy observations were used to calibrate the parameters in sub-canopy radiation, turbulence and resistances modules with an automatic tuning process following the maximum gradient of the user-defined objective function. The multi-layer model is able to capture the dynamic of sub-canopy turbulence, temperature and energy fluxes with imposed LAI profile and optimized parameter set at a site level calibration. The simulation result shows the improvement both on the nighttime energy balance and energy partitioning during winter and presents a better Taylor skill score, compared to the result from single layer simulation. The importance of using the multi-layer energy budget in a land surface model for coupling to the atmospheric model will also be discussed in this presentation. Reference: Ryder, J., J. Polcher, P. Peylin, C. Ottlé, Y. Chen, E. Van Gorsel, V. Haverd, M. J. McGrath, K.Naudts, J. Otto, A. Valade, and S. Luyssaert, 2014. "A multi-layer land surface energy budget model for implicit coupling with global atmospheric simulations", Geosci. Model Dev. Discuss. 7, 8649-8701 Naudts, K. J. Ryder, M. J. McGrath, J. Otto, Y. Chen, A. Valade, V. Bellasen, G. Berhongaray, G. Bönisch, M. Campioli, J. Ghattas, T. De Groote, V. Haverd, J. Kattge, N. MacBean, F. Maignan, P. Merilä, J. Penuelas, P. Peylin, B. Pinty, H. Pretzsch, E. D. Schulze, D. Solyga, N. Vuichard, Y. Yan, and S. Luyssaert, 2014. "A vertically discretised canopy description for ORCHIDEE (SVN r2290) and the modifications to the energy, water and carbon fluxes", Geosci. Model Dev. Discuss. 7, 8565-8647

Coupled carbon-water exchange of the Amazon rain forest, II. Comparison of predicted and observed seasonal exchange of energy, CO2, isoprene and ozone at a remote site in Rondônia

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Rummel, U.; Ganzeveld, L.; Ammann, C.; Kesselmeier, J.

2005-10-01

A one-dimensional multi-layer scheme describing the coupled exchange of energy and CO2, the emission of isoprene and the dry deposition of ozone is applied to a rain forest canopy in southwest Amazonia. The model was constrained using mean diel cycles of micrometeorological quantities observed during two periods in the wet and dry season 1999. Calculated net fluxes and concentration profiles for both seasonal periods are compared to observations made at two nearby towers.

The modeled day- and nighttime thermal stratification of the canopy layer is consistent with observations in dense canopies. The observed and modeled net fluxes above and H2O and CO2 concentration profiles within the canopy show a good agreement. The predicted net carbon sink decreases from 2.5 t C ha-1 yr-1 for wet season conditions to 1 t C ha-1 yr-1 for dry season conditions, whereas observed and modeled midday Bowen ratio increases from 0.5 to 0.8. The evaluation results confirmed a seasonal variability of leaf physiological parameters, as already suggested in a companion study. The calculated midday canopy net flux of isoprene increased from 7.1 mg C m-2 h-1 during the wet season to 11.4 mg C m-2 h-1 during the late dry season. Applying a constant emission capacity in all canopy layers, resulted in a disagreement between observed and simulated profiles of isoprene concentrations, suggesting a smaller emission capacity of shade adapted leaves and deposition to the soil or leaf surfaces. Assuming a strong light acclimation of emission capacity, equivalent to a 66% reduction of the standard emission factor for leaves in the lower canopy, resulted in a better agreement of observed and modeled concentration profiles and a 30% reduction of the canopy net flux compared to model calculations with a constant emission factor. The mean calculated ozone flux for dry season conditions at noontime was ≍12 n mol m-2 s-1, agreeing well with observed values. The corresponding deposition velocity increased from 0.8 cm s-1 to >1.6 cm s-1 in the wet season, which can not be explained by increased stomatal uptake. Considering reasonable physiological changes in stomatal regulation, the modeled value was not larger than 1.05 cm s-1. Instead, the observed fluxes could be explained with the model by decreasing the cuticular resistance to ozone deposition from 5000 to 1000 s m-1.

Advanced control design for hybrid turboelectric vehicle

NASA Technical Reports Server (NTRS)

Abban, Joseph; Norvell, Johnesta; Momoh, James A.

1995-01-01

The new environment standards are a challenge and opportunity for industry and government who manufacture and operate urban mass transient vehicles. A research investigation to provide control scheme for efficient power management of the vehicle is in progress. Different design requirements using functional analysis and trade studies of alternate power sources and controls have been performed. The design issues include portability, weight and emission/fuel efficiency of induction motor, permanent magnet and battery. A strategic design scheme to manage power requirements using advanced control systems is presented. It exploits fuzzy logic, technology and rule based decision support scheme. The benefits of our study will enhance the economic and technical feasibility of technological needs to provide low emission/fuel efficient urban mass transit bus. The design team includes undergraduate researchers in our department. Sample results using NASA HTEV simulation tool are presented.

Urban bioclimatology in developing countries.

PubMed

Jauregui, E

1993-11-15

A brief review of the literature on urban human bioclimatology in the tropics is undertaken. Attempts to chart human bioclimatic conditions on the regional/local scale have been made in several developing countries. The effective temperature scheme (with all its limitations) is the one that has been most frequently applied. The possibilities of application of bioclimatic models based on human heat balance for the tropical urban environment are discussed.

Influence of Dynamics and Chemistry on the Diurnal Variation of VOCs in the Planetary Boundary Layer above a Mixed Forest Canopy in the Southeastern United States

NASA Astrophysics Data System (ADS)

Guenther, A. B.; Su, L.; Patton, E. G.; Vila-Guerau Arellano, J.; Mak, J. E.

2014-12-01

The planetary boundary layer (PBL) is a region of inherent interest because reactive VOCs emitted from the forest canopy are mixed with the residual and free tropospheric air masses, oxidized, and/or otherwise removed in this region. The characterization of diurnal variation of VOCs in the PBL is limited due to the lack of appropriate sampling platforms that are able to probe all the regions of interest: from the surface to the entrainment zone. Here we present the application of the Whole Air Sample Profiler (WASP) system during the 2013 Southeast Atmosphere Study (SAS) campaign. A total of 41 research flights (RFs) were carried out during the 2013 SAS campaign between June 1 and June 14 over the Alabama Aquatic Biodiversity Center (AABC) site and the SEARCH site. During each RF, ambient air sampling started from 50-100 m above the canopy top and stopped at ~1200 m above the mean sea level (a.m.s.l). The air samples were subsequently analyzed by using a proton-transfer-reaction time-of-flight mass spectrometry (PTR-TOF-MS). Here we analyze the vertical profiles and averaged diurnal variation of the mixing ratios of several reactive VOC species, including isoprene, the sum of monoterpenes, and first generation oxidation products of isoprene: methyl vinyl ketone and methacrolein (MVK+MACR). A MiXed Layer Chemistry (MXLCH) model, guided by the meteorological and chemical observations during the SAS campaign, is used to study the influence of boundary layer dynamics and new isoprene oxidation mechanism on the diurnal variation of major biogenic VOCs emitted from the forest canopy. The new scheme includes OH recycling through two pathways under low-NOx regime: (1) hydroxyl peroxy radicals (HOC5H8OO•; ISOPO2) unimolecular isomerization, and (2) ISOPO2+HO2. The model is able to reproduce the evolution of the boundary layer dynamics (including potential temperature, and boundary layer height) during the selected simulation dates. Based on the model results, budget analyses are performed to study the roles that the boundary layer dynamics and chemistry play in controlling the evolution of VOCs in the PBL. Chemical tendencies of important species, including organic peroxy radicals (RO2), HO2, and OH are calculated to evaluate the capacity of the new isoprene scheme in explaining the photooxidation processes in the PBL.

Future Urban Climate Projection in A Tropical Megacity Based on Global and Regional Scenarios

NASA Astrophysics Data System (ADS)

Darmanto, N. S.; Varquez, A. C. G.; Kanda, M.

2017-12-01

Cities in Asian developing countries experience rapid transformation in urban morphology and energy consumption, which correspondingly affects urban climate. Weather Research and Forecasting (WRF) Model coupled with improved single-layer urban canopy model incorporating realistic distribution of urban parameters and anthropogenic heat emission (AHE) in the tropic Jakarta Greater Area was conducted. Simulation was conducted during the dry months from 2006 to 2015 and agreed well with point and satellite observation. The same technology coupled with pseudo global warming (PGW) method based on representative concentration pathways (RCP) scenario 2.6 and 8.5 was conducted to produce futuristic climate condition in 2050. Projected urban morphology and AHE in 2050s were constructed using regional urban growing model with shared socioeconomic pathways (SSP) among its inputs. Compact future urban configuration, based on SSP1, was coupled to RCP2.6. Unrestrained future urban configuration, based on SSP3, was coupled to RCP8.5. Results show that background warming from RCP 2.6 and 8.5 will increase background temperature by 0.55°C and 1.2°C throughout the region, respectively. Future projection of urban sprawl results to an additional 0.3°C and 0.5°C increase on average, with maximum increase of 1.1°C and 1.3°C due to urban effect for RCP2.6/compact and RCP8.5/unrestrained, respectively. Higher moisture content in urban area is indicated in the future due to higher evaporation. Change in urban roughness is likely affect slower wind velocity in urban area and sea breeze front inland penetration the future compare with current condition. Acknowledgement: This research was supported by the Environment Research and Technology Development Fund (S-14) of the Ministry of the Environment, Japan.

Remote Sensing and Spatial Growth Modeling Coupled with Air Quality Modeling to Assess the Impact of Atlanta, Georgia on the Local and Regional Environment

NASA Technical Reports Server (NTRS)

Quattrochi, Dale A.; Estes, Maurice G., Jr.; Crosson, William; Khan, Maudood

2006-01-01

The growth of cities, both in population and areal extent, appears as an inexorable process. Urbanization continues at a rapid rate, and it is estimated that by the year 2025, 80 percent of the world s population will live in cities. Directly aligned with the expansion of cities is urban sprawl. Urban expansion has profound impacts on a host of biophysical, environmental, and atmospheric processes. A reduction in air quality over cities is a major result of these impacts. Strategies that can be directly or indirectly implemented to help remediate air quality problems in cities and that can be accepted by political decision makers and the general public are now being explored to help bring down air pollutants and improve air quality. The urban landscape is inherently complex and this complexity is not adequately captured in air quality models, particularly the Community Multiscale Air Quality (CMAQ) model that is used to assess whether urban areas are in attainment of EPA air quality standards, primarily for ground level ozone. This inadequacy of the CMAQ model to sufficiently respond to the heterogeneous nature of the urban landscape can impact how well the model predicts ozone pollutant levels over metropolitan areas and ultimately, whether cities exceed EPA ozone air quality standards. We are exploring the utility of high-resolution remote sensing data and urban spatial growth modeling (SGM) projections as improved inputs to the meteorology component of the CMAQ model focusing on the Atlanta, Georgia metropolitan area as a case study. These growth projections include "business as usual" and "smart growth" scenarios out to 2030. The growth projections illustrate the effects of employing urban heat island mitigation strategies, such as increasing tree canopy and albedo across the Atlanta metro area, which in turn, are used to model how ozone and air temperature can potentially be moderated as impacts on elevating ground-level ozone, as opposed to not utilizing heat island mitigation strategies. The National Land Cover Dataset at 30m resolution is being used as the land use/land cover input and aggregated to the 4km scale for the MM5 mesoscale meteorological model and the (CMAQ) modeling schemes. Use of these data have been found to better characterize low density/suburban development as compared with USGS 1km land use/land cover data that have traditionally been used in modeling. Air quality prediction for future scenarios to 2030 is being facilitated by land use projections using a spatial growth model. Land use projections were developed using the 2030 Regional Transportation Plan developed by the Atlanta Regional Commission, the regional planning agency for the area. This allows the State Environmental Protection agency to evaluate how these transportation plans will affect future air quality. The coupled SGM and air quality modeling approach provides insight on what the impacts of Atlanta s growth will be on the local and regional environment and exists as a mechanism that can be used by policy makers to make rationale decisions on urban growth and sustainability for the metropolitan area in the future.

Comparison of selected approaches for urban roughness determination based on voronoi cells.

PubMed

Ketterer, Christine; Gangwisch, Marcel; Fröhlich, Dominik; Matzarakis, Andreas

2017-01-01

Wind speed is reduced above urban areas due to their high aerodynamic roughness. This not only holds for above the urban canopy. The local vertical wind profile is modified. Aerodynamic roughness (both roughness length and displacement height) therefore is relevant for many fields within human biometeorology, e.g. for the identification of ventilation paths, the concentration and dispersion of air pollutants at street level or to simulate wind speed and direction in urban environments and everything depending on them. Roughness, thus, also shows strong influence on human thermal comfort. Currently, roughness parameters are mostly estimated using classifications. However, such classifications only provide limited assessment of roughness in urban areas. In order to calculate spatially resolved roughness on the micro-scale, three different approaches were implemented in the SkyHelios model. For all of them, the urban area is divided into reference areas for each of the obstacles using a voronoi diagram. The three approaches are based on building and [+one of them also on] vegetation (trees and forests) data. They were compared for the city of Stuttgart, Germany. Results show that the approach after Bottema and Mestayer (J Wind Eng Ind Aerodyn 74-76:163-173 1998) on the spatial basis of a voronoi diagram provides the most plausible results.

Focusing on the big picture: urban vegetation and eco ...

EPA Pesticide Factsheets

Trees and vegetation can be key components of urban green infrastructure and green spaces such as parks and residential yards. Large trees, characterized by broad canopies, and high leaf and stem volumes, can intercept a substantial amount of stormwater while promoting evapotranspiration and reducing stormwater runoff and pollutant loads. Urban vegetation cover, height, and volume are likely to be affected not only by local climatic characteristics, but also by complex socio-economic dynamics resulting from management practices and resident’s preferences. We examine the benefits provided by private greenspace and present preliminary findings related to the climatic and socio-economic drivers correlated with structural complexity of residential urban vegetation. We use laser (LiDAR) and multispectral remotely-sensed data collected throughout 1400+ neighborhoods and 1.2+ million residential yards across 8 US cities to carry out this analysis. We discuss principles and opportunities to enhance stormwater management using residential greenspace, as well as the larger implications for decentralized stormwater management at city-wide scale. We discuss principles and opportunities to enhance stormwater management using residential greenspace, as well as the larger implications for decentralized stormwater management at city-wide scale.

Large-eddy simulation of pollutant dispersion from a ground-level area source over urban street canyons with irreversible chemical reactions

NASA Astrophysics Data System (ADS)

Du, T. Z.; Liu, C.-H.; Zhao, Y. B.

2014-10-01

In this study, the dispersion of chemically reactive pollutants is calculated by large-eddy simulation (LES) in a neutrally stratified urban canopy layer (UCL) over urban areas. As a pilot attempt, idealized street canyons of unity building-height-to-street-width (aspect) ratio are used. Nitric oxide (NO) is emitted from the ground surface of the first street canyon into the domain doped with ozone (O3). In the absence of ultraviolet radiation, this irreversible chemistry produces nitrogen dioxide (NO2), developing a reactive plume over the rough urban surface. A range of timescales of turbulence and chemistry are utilized to examine the mechanism of turbulent mixing and chemical reactions in the UCL. The Damköhler number (Da) and the reaction rate (r) are analyzed along the vertical direction on the plane normal to the prevailing flow at 10 m after the source. The maximum reaction rate peaks at an elevation where Damköhler number Da is equal or close to unity. Hence, comparable timescales of turbulence and reaction could enhance the chemical reactions in the plume.

Built Expansion and Global Climate Change Drive Projected Urban Heat: Relative Magnitudes, Interactions, and Mitigation

NASA Astrophysics Data System (ADS)

Krayenhoff, E. S.; Georgescu, M.; Moustaoui, M.

2016-12-01

Surface climates are projected to warm due to global climate change over the course of the 21st century, and demographic projections suggest urban areas in the United States will continue to expand and develop, with associated local climate outcomes. Interactions between these two drivers of urban heat have not been robustly quantified to date. Here, simulations with the Weather Research and Forecasting model (coupled to a Single-Layer Urban Canopy Model) are performed at 20 km resolution over the continental U.S. for two 10-year periods: contemporary (2000-2009) and end-of-century (2090-2099). Present and end of century urban land use are derived from the Environmental Protection Agency's Integrated Climate and Land-Use Scenarios. Modelled effects on urban climates are evaluated regionally. Sensitivity to climate projection (Community Climate System Model 4.0, RCP 4.5 vs. RCP 8.5) and associated urban development scenarios are assessed. Effects on near-surface urban air temperature of RCP8.5 climate change are greater than those attributable to the corresponding urban development in many regions. Interaction effects vary by region, and while of lesser magnitude, are not negligible. Moreover, urban development and its interactions with RCP8.5 climate change modify the distribution of convective precipitation over the eastern US. Interaction effects result from the different meteorological effects of urban areas under current and future climate. Finally, the potential for design implementations such as green roofs and high albedo roofs to offset the projected warming is considered. Impacts of these implementations on precipitation are also assessed.

Impact of WRF model PBL schemes on air quality simulations over Catalonia, Spain.

PubMed

Banks, R F; Baldasano, J M

2016-12-01

Here we analyze the impact of four planetary boundary-layer (PBL) parametrization schemes from the Weather Research and Forecasting (WRF) numerical weather prediction model on simulations of meteorological variables and predicted pollutant concentrations from an air quality forecast system (AQFS). The current setup of the Spanish operational AQFS, CALIOPE, is composed of the WRF-ARW V3.5.1 meteorological model tied to the Yonsei University (YSU) PBL scheme, HERMES v2 emissions model, CMAQ V5.0.2 chemical transport model, and dust outputs from BSC-DREAM8bv2. We test the performance of the YSU scheme against the Assymetric Convective Model Version 2 (ACM2), Mellor-Yamada-Janjic (MYJ), and Bougeault-Lacarrère (BouLac) schemes. The one-day diagnostic case study is selected to represent the most frequent synoptic condition in the northeast Iberian Peninsula during spring 2015; regional recirculations. It is shown that the ACM2 PBL scheme performs well with daytime PBL height, as validated against estimates retrieved using a micro-pulse lidar system (mean bias=-0.11km). In turn, the BouLac scheme showed WRF-simulated air and dew point temperature closer to METAR surface meteorological observations. Results are more ambiguous when simulated pollutant concentrations from CMAQ are validated against network urban, suburban, and rural background stations. The ACM2 scheme showed the lowest mean bias (-0.96μgm -3 ) with respect to surface ozone at urban stations, while the YSU scheme performed best with simulated nitrogen dioxide (-6.48μgm -3 ). The poorest results were with simulated particulate matter, with similar results found with all schemes tested. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Towards developing Kentucky's landscape change maps

USGS Publications Warehouse

Zourarakis, D.P.; Lambert, S.C.; Palmer, M.

2003-01-01

The Kentucky Landscape Snapshot Project, a NASA-funded project, was established to provide a first baseline land cover/land use map for Kentucky. Through this endeavor, change detection will be institutionalized, thus aiding in decision-making at the local, state, and federal planning levels. 2002 Landsat 7 imaginery was classified following and Anderson Level III scheme, providing an enhancement over the 1992 USGS National Land Cover Data Set. Also as part of the deliverables, imperviousness and canopy closure layers were produced with the aid of IKONOS high resolution, multispectral imagery.

Modeling the Warming Impact of Urban Land Expansion on Hot Weather Using the Weather Research and Forecasting Model: A Case Study of Beijing, China

NASA Astrophysics Data System (ADS)

Liu, Xiaojuan; Tian, Guangjin; Feng, Jinming; Ma, Bingran; Wang, Jun; Kong, Lingqiang

2018-06-01

The impacts of three periods of urban land expansion during 1990-2010 on near-surface air temperature in summer in Beijing were simulated in this study, and then the interrelation between heat waves and urban warming was assessed. We ran the sensitivity tests using the mesoscaleWeather Research and Forecasting model coupled with a single urban canopy model, as well as high-resolution land cover data. The warming area expanded approximately at the same scale as the urban land expansion. The average regional warming induced by urban expansion increased but the warming speed declined slightly during 2000-2010. The smallest warming occurred at noon and then increased gradually in the afternoon before peaking at around 2000 LST—the time of sunset. In the daytime, urban warming was primarily caused by the decrease in latent heat flux at the urban surface. Urbanization led to more ground heat flux during the day and then more release at night, which resulted in nocturnal warming. Urban warming at night was higher than that in the day, although the nighttime increment in sensible heat flux was smaller. This was because the shallower planetary boundary layer at night reduced the release efficiency of near-surface heat. The simulated results also suggested that heat waves or high temperature weather enhanced urban warming intensity at night. Heat waves caused more heat to be stored in the surface during the day, greater heat released at night, and thus higher nighttime warming. Our results demonstrate a positive feedback effect between urban warming and heat waves in urban areas.

Follow-on proposal identifying environmental features for land management decisions

NASA Technical Reports Server (NTRS)

Wright, P. M.; Ridd, M. K.

1986-01-01

Urban morphology (an examination of spatial fabric and structure), natural ecosystem (investigations emphasizing biophysical processes and patterns), and human ecosystem (emphasizing socio-economic and engineering parameters) were studied. The most critical variable, transpiration, in the ASPCON model, created by Jaynes (1978), describing the hydrology of aspen to conifer succession was studied to improve the accuracy. Transpiration is determined by a canopy transpiration model which estimates consumptive water use (CWU) for specific species and a plant activity index. Also studied was Pinyon-Juniper woodland erosion.

The Implement of a Multi-layer Frozen Soil Scheme into SSiB3 and its Evaluation over Cold Regions

NASA Astrophysics Data System (ADS)

Li, Q.

2016-12-01

The SSiB3 is a biophysics-based model of land-atmosphere interactions and is designed for global and regional studies. It has three soil layers, three snow layers, as well as one vegetation layer. Soil moisture of the three soil layers, interception water store for the canopy, subsurface soil temperature, ground temperature, canopy temperature and snow water equivalent are all predicted based on the water and energy balance at canopy, soil and snow. SSiB3 substantially enhances the model's capability for cold season studies and produces reasonable results compared with observations. However, frozen soil processes are ignored in the SSiB3 and may have effects on the interannual variability of soil temperature and deep soil memory. A multi-layer comprehensive frozen soil scheme (FSM), which is developed for climate study has been implemented into the SSiB3 to describe soil heat transfer and water flow affected by frozen processed in soil. In the coupled SSiB3-FSM, both liquid water and ice content have been taken into account in the frozen soil hydrologic and thermal property parameterization. The maximum soil layer depth could reach 10 meters thick depending on land conditions. To better evaluate the models' performance, the coupled offline SSiB3-FSM and SSiB3 have been driven from 1948 to 1958 by the Princeton global meteorological data set, respectively. For the 10yrs run, the coupled SSiB3-FSM almost captures the features over different regions, especially cold regions. In order to analysis and compare the differences of SSIB3-FSM and SSIB3 in detail, monthly mean surface temperature for different regions are compared with CAMS data. The statistical results of surface skin temperature show that high latitude regions, Africa, Eastern Australia, and North American monsoon regions have been greatly improved in SSIB3-FSM. For the global statistics, the RMSE of the surface temperature simulated by SSiB3-FSM can be improved about 0.6K compared to SSiB3. In this study, the improvements in the coupled SSiB3-FSM have also been analyzed.

Predicting the dry deposition of atmospheric aerosol particles onto forests using a size-resolved multi-layer second-order closure model

NASA Astrophysics Data System (ADS)

Huang, C.; Launianen, S.; Gronholm, T.; Katul, G. G.

2013-12-01

Biological aerosol particles are now receiving significant attention given their role in air quality, climate change, and spreading of allergens and other communicable diseases. A major uncertainty in their quantification is associated with complex transport processes governing their generation and removal inside canopies. It has been known for some time now that the commonly used first-order closure to link mean concentration gradients with turbulent fluxes is problematic. The presence of a mean counter-gradient momentum transport in an open trunk space exemplifies such failure. Here, instead of employing K-theory, a size-resolved second-order multilayer model for dry particle deposition is proposed. The starting point of the proposed model is a particle flux budget in which the production, transport, and dissipation terms are modeled. Because these terms require higher-order velocity statistics, this flux budget is coupled with a conventional second-order closure scheme for the flow field within the canopy sub-layer. The failure of conventional K-theory for particle fluxes are explicitly linked to the onset of a mean counter or zero - gradient flow attributed to a significant particle flux transport term. The relative importance of these terms in the particle flux budget and their effects on the foliage particle collection terms for also discussed for each particle size. The proposed model is evaluated against published multi-level measurements of sized-resolved particle fluxes and mean concentration profiles collected within and above a tall Scots pine forest in Hyytiala, Southern Finland. The main findings are that (1) first-order closure schemes may be still plausible for modeling particle deposition velocity, especially in the particle size range smaller than 1 μm when the turbulent particle diffusivity is estimated from higher order flow statistics; (2) the mechanisms leading to the increased trend of particle deposition velocity with increasing friction velocity differ for different particle sizes and different levels (i.e. above and below the canopy); (3) the partitioning of particle deposition onto foliage and forest floor appears insensitive to friction velocity for particles smaller than 100 nm, but decreases with increasing friction velocity for particles large than 100 nm.

Defining "Rural" for Veterans' Health Care Planning

ERIC Educational Resources Information Center

West, Alan N.; Lee, Richard E.; Shambaugh-Miller, Michael D.; Bair, Byron D.; Mueller, Keith J.; Lilly, Ryan S.; Kaboli, Peter J.; Hawthorne, Kara

2010-01-01

Purpose: The Veterans Health Administration (VHA) devised an algorithm to classify veterans as Urban, Rural, or Highly Rural residents. To understand the policy implications of the VHA scheme, we compared its categories to 3 Office of Management and Budget (OMB) and 4 Rural-Urban Commuting Area (RUCA) geographical categories. Method: Using…

A real-time control framework for urban water reservoirs operation

NASA Astrophysics Data System (ADS)

Galelli, S.; Goedbloed, A.; Schwanenberg, D.

2012-04-01

Drinking water demand in urban areas is growing parallel to the worldwide urban population, and it is acquiring an increasing part of the total water consumption. Since the delivery of sufficient water volumes in urban areas represents a difficult logistic and economical problem, different metropolitan areas are evaluating the opportunity of constructing relatively small reservoirs within urban areas. Singapore, for example, is developing the so-called 'Four National Taps Strategies', which detects the maximization of water yields from local, urban catchments as one of the most important water sources. However, the peculiar location of these reservoirs can provide a certain advantage from the logistical point of view, but it can pose serious difficulties in their daily management. Urban catchments are indeed characterized by large impervious areas: this results in a change of the hydrological cycle, with decreased infiltration and groundwater recharge, and increased patterns of surface and river discharges, with higher peak flows, volumes and concentration time. Moreover, the high concentrations of nutrients and sediments characterizing urban discharges can cause further water quality problems. In this critical hydrological context, the effective operation of urban water reservoirs must rely on real-time control techniques, which can exploit hydro-meteorological information available in real-time from hydrological and nowcasting models. This work proposes a novel framework for the real-time control of combined water quality and quantity objectives in urban reservoirs. The core of this framework is a non-linear Model Predictive Control (MPC) scheme, which employs the current state of the system, the future discharges furnished by a predictive model and a further model describing the internal dynamics of the controlled sub-system to determine an optimal control sequence over a finite prediction horizon. The main advantage of this scheme stands in its reduced computational requests and the capability of exploiting real-time hydro-meteorological information, which are crucial for an effective operation of these fast-varying hydrological systems. The framework is here demonstrated on the operation of Marina Reservoir (Singapore), whose recent construction in late 2008 increased the effective catchment area to about 50% of the total available. Its operation, which accounts for drinking water supply, flash floods control and water quality standards, is here designed by combining the MPC scheme with the process-based hydrological model SOBEK. Extensive simulation experiments show the validity of the proposed framework.

Characterizing tree canopy temperature heterogeneity using an unmanned aircraft-borne thermal imager

NASA Astrophysics Data System (ADS)

Messinger, M.; Powell, R.; Silman, M.; Wright, M.; Nicholson, W.

2013-12-01

Leaf temperature (Tleaf) is an important control on many physiological processes such as photosynthesis and respiration, is a key variable for characterizing canopy energy fluxes, and is a valuable metric for identifying plant water stress or disease. Traditional methods of Tleaf measurement involve either the use of thermocouples, a time and labor-intensive method that samples sparsely in space, or the use of air temperature (Tair) as a proxy measure, which can introduce inaccuracies due to near constant canopy-atmosphere energy flux. Thermal infrared (TIR) imagery provides an efficient means of collecting Tleaf for large areas. Existing satellite and aircraft-based TIR imagery is, however, limited by low spatial and/or temporal resolution, while crane-mounted camera systems have strictly limited spatial extents. Unmanned aerial systems (UAS) offer new opportunities to acquire high spatial and temporal resolution imagery on demand. Here, we demonstrate the feasibility of collecting tree canopy Tleaf data using a small multirotor UAS fitted with a high spatial resolution TIR imager. The goals of this pilot study were to a) characterize basic patterns of within crown Tleaf for 4 study species and b) identify trends in Tleaf between species with varying leaf morphologies and canopy structures. TIR imagery was acquired for individual tree crowns of 4 species common to the North Carolina Piedmont ecoregion (Quercus phellos, Pinus strobus, Liriodendron tulipifera, Magnolia grandiflora) in an urban park environment. Due to significantly above-average summer precipitation, we assumed that none of the sampled trees was limited by soil water availability. We flew the TIR imaging system over 3-4 individuals of each of the 4 target species on 3 separate days. Imagery of all individuals was collected within the same 2-hour period in the afternoon on all days. There was low wind and partly cloudy skies during imaging. Tair, relative humidity, and wind speed were recorded at each site. Emissivity was assumed to be 0.98 for all species. Acquired images had a pixel resolution of <3 cm and measurement accuracy of ×1° C. We found the UAS-borne TIR imaging system to be an effective tool for collection of high resolution canopy imagery. The system imaged all targeted crowns quickly and reliably, providing a viable alternative to current methods of canopy Tleaf measurement. Analysis of the imagery indicated significant variability in Tleaf both within and between crowns. We identified trends in Tleaf related to average leaf size, shape, and crown structural traits. These data on the heterogeneity of Tleaf can further our understanding of canopy-atmosphere energy exchange. This pilot study demonstrates the promise of UAS-borne TIR sensors for acquiring high spatial resolution imagery at the scale of individual tree crowns.

Turbulence and pollutant transport in urban street canyons under stable stratification: a large-eddy simulation

NASA Astrophysics Data System (ADS)

Li, X.

2014-12-01

Thermal stratification of the atmospheric surface layer has strong impact on the land-atmosphere exchange of turbulent, heat, and pollutant fluxes. Few studies have been carried out for the interaction of the weakly to moderately stable stratified atmosphere and the urban canopy. This study performs a large-eddy simulation of a modeled street canyon within a weakly to moderately stable atmosphere boundary layer. To better resolve the smaller eddy size resulted from the stable stratification, a higher spatial and temporal resolution is used. The detailed flow structure and turbulence inside the street canyon are analyzed. The relationship of pollutant dispersion and Richardson number of the atmosphere is investigated. Differences between these characteristics and those under neutral and unstable atmosphere boundary layer are emphasized.

Nesting tree characteristics of heronry birds of urban ecosystems in peninsular India: implications for habitat management

PubMed Central

Sinu, Palatty Allesh

2017-01-01

Abstract Wetland ecosystems, particularly the mangrove forest, are the primary wild habitat of heronry birds. However, urban ecosystems have become a favorite breeding habitat of these birds. To provide inputs into the habitat management for conservation of these birds, we investigated the quantitative and qualitative characteristics of nesting trees of heronry birds in the urban environment of the North Kerala region of peninsular India. Census on nesting trees was done in 3 major microhabitats of the urban ecosystem: avenues of national highways and towns, nonresidential plots, and residential areas apart from the mangrove islets in the peri-urban locality. The study found that 174 trees of 22 species hosted 1,928 heronry bird nests in the urban habitats; mangrove forests, although plentiful in the study area, hosted only about 20% of the total nests encountered in the study. Rain trees Samanea saman (43.7%) were the most available nesting tree. The greatest number of nests and nesting trees were encountered on the roads of urban areas, followed by nonresidential areas and residential areas. The differences in the observed frequencies of nesting trees in 3 microhabitats and in 3 types of roads (national highways > state highways > small pocket road) were significant. Canopy spread, girth size, and quality of the trees predicted the tree selection of the heronry birds in urban environments. Therefore, we recommend proper management and notification of the identified nesting trees as protected sites for the conservation of herorny birds. PMID:29492020

Nesting tree characteristics of heronry birds of urban ecosystems in peninsular India: implications for habitat management.

PubMed

Roshnath, Ramesh; Sinu, Palatty Allesh

2017-12-01

Wetland ecosystems, particularly the mangrove forest, are the primary wild habitat of heronry birds. However, urban ecosystems have become a favorite breeding habitat of these birds. To provide inputs into the habitat management for conservation of these birds, we investigated the quantitative and qualitative characteristics of nesting trees of heronry birds in the urban environment of the North Kerala region of peninsular India. Census on nesting trees was done in 3 major microhabitats of the urban ecosystem: avenues of national highways and towns, nonresidential plots, and residential areas apart from the mangrove islets in the peri-urban locality. The study found that 174 trees of 22 species hosted 1,928 heronry bird nests in the urban habitats; mangrove forests, although plentiful in the study area, hosted only about 20% of the total nests encountered in the study. Rain trees Samanea saman (43.7%) were the most available nesting tree. The greatest number of nests and nesting trees were encountered on the roads of urban areas, followed by nonresidential areas and residential areas. The differences in the observed frequencies of nesting trees in 3 microhabitats and in 3 types of roads (national highways > state highways > small pocket road) were significant. Canopy spread, girth size, and quality of the trees predicted the tree selection of the heronry birds in urban environments. Therefore, we recommend proper management and notification of the identified nesting trees as protected sites for the conservation of herorny birds.

Urbanization Level and Woodland Size Are Major Drivers of Woodpecker Species Richness and Abundance

PubMed Central

Myczko, Łukasz; Rosin, Zuzanna M.; Skórka, Piotr; Tryjanowski, Piotr

2014-01-01

Urbanization is a process globally responsible for loss of biodiversity and for biological homogenization. Urbanization may have a direct negative impact on species behaviour and indirect effects on species populations through alterations of their habitats, for example patch size and habitat quality. Woodpeckers are species potentially susceptible to urbanization. These birds are mostly forest specialists and the development of urban areas in former forests may be an important factor influencing their richness and abundance, but documented examples are rare. In this study we investigated how woodpeckers responded to changes in forest habitats as a consequence of urbanization, namely size and isolation of habitat patches, and other within-patch characteristics. We selected 42 woodland patches in a gradient from a semi-natural rural landscape to the city centre of Poznań (Western Poland) in spring 2010. Both species richness and abundance of woodpeckers correlated positively to woodland patch area and negatively to increasing urbanization. Abundance of woodpeckers was also positively correlated with shrub cover and percentage of deciduous tree species. Furthermore, species richness and abundance of woodpeckers were highest at moderate values of canopy openness. Ordination analyses confirmed that urbanization level and woodland patch area were variables contributing most to species abundance in the woodpecker community. Similar results were obtained in presence-absence models for particular species. Thus, to sustain woodpecker species within cities it is important to keep woodland patches large, multi-layered and rich in deciduous tree species. PMID:24740155

Urbanization level and woodland size are major drivers of woodpecker species richness and abundance.

PubMed

Myczko, Lukasz; Rosin, Zuzanna M; Skórka, Piotr; Tryjanowski, Piotr

2014-01-01

Urbanization is a process globally responsible for loss of biodiversity and for biological homogenization. Urbanization may have a direct negative impact on species behaviour and indirect effects on species populations through alterations of their habitats, for example patch size and habitat quality. Woodpeckers are species potentially susceptible to urbanization. These birds are mostly forest specialists and the development of urban areas in former forests may be an important factor influencing their richness and abundance, but documented examples are rare. In this study we investigated how woodpeckers responded to changes in forest habitats as a consequence of urbanization, namely size and isolation of habitat patches, and other within-patch characteristics. We selected 42 woodland patches in a gradient from a semi-natural rural landscape to the city centre of Poznań (Western Poland) in spring 2010. Both species richness and abundance of woodpeckers correlated positively to woodland patch area and negatively to increasing urbanization. Abundance of woodpeckers was also positively correlated with shrub cover and percentage of deciduous tree species. Furthermore, species richness and abundance of woodpeckers were highest at moderate values of canopy openness. Ordination analyses confirmed that urbanization level and woodland patch area were variables contributing most to species abundance in the woodpecker community. Similar results were obtained in presence-absence models for particular species. Thus, to sustain woodpecker species within cities it is important to keep woodland patches large, multi-layered and rich in deciduous tree species.

Impact of Photovoltaic Canopy Shade on Outdoor Thermal Comfort in a Hot Desert City

NASA Astrophysics Data System (ADS)

Middel, Ariane; Selover, Nancy; Hagen, Björn; Chhetri, Nalini

2016-04-01

Shade plays an important role in designing pedestrian-friendly outdoor spaces in hot desert cities. This study investigates the impact of photovoltaic canopy shade on thermal comfort through microclimate observations and field surveys at a pedestrian mall on Arizona State University's Tempe campus. Six stationary sensors under solar canopies and in nearby sun-exposed and tree-shaded locations monitored 5-min temperature and humidity for a year. On selected clear calm days representative of each season, we conducted hourly microclimate transects from 7:00AM to 6:00PM and surveyed 1284 people about their thermal perception, comfort, and preferences. Shade lowered thermal sensation votes by approximately 1 point on the Likert scale, increasing thermal comfort in all seasons except winter. The shade type (tree or solar canopy) did not significantly impact perceived comfort, suggesting that artificial and natural shade are equally efficient in semi-arid desert environments. Globe temperature explained 50% of the variance in thermal sensation votes and was the only statistically significant meteorological predictor. Important non-meteorological factors include adaptation level, gender, thermal comfort vote, thermal preference, season, and time of day. A regression of perceived comfort on Physiological Equivalent Temperature yielded a neutral temperature of 28.6°C. The acceptable comfort range was 19.1°C-38.1°C with a preferred temperature of 20.8°C. Respondents exposed to above neutral temperatures felt more comfortable if they had been in air-conditioning 5 minutes prior to the survey, indicating a lagged response to outdoor conditions. Our study highlights the importance of active solar access management in hot urban areas.

Leaf and life history traits predict plant growth in a green roof ecosystem.

PubMed

Lundholm, Jeremy; Heim, Amy; Tran, Stephanie; Smith, Tyler

2014-01-01

Green roof ecosystems are constructed to provide services such as stormwater retention and urban temperature reductions. Green roofs with shallow growing media represent stressful conditions for plant survival, thus plants that survive and grow are important for maximizing economic and ecological benefits. While field trials are essential for selecting appropriate green roof plants, we wanted to determine whether plant leaf traits could predict changes in abundance (growth) to provide a more general framework for plant selection. We quantified leaf traits and derived life-history traits (Grime's C-S-R strategies) for 13 species used in a four-year green roof experiment involving five plant life forms. Changes in canopy density in monocultures and mixtures containing one to five life forms were determined and related to plant traits using multiple regression. We expected traits related to stress-tolerance would characterize the species that best grew in this relatively harsh setting. While all species survived to the end of the experiment, canopy species diversity in mixture treatments was usually much lower than originally planted. Most species grew slower in mixture compared to monoculture, suggesting that interspecific competition reduced canopy diversity. Species dominant in mixture treatments tended to be fast-growing ruderals and included both native and non-native species. Specific leaf area was a consistently strong predictor of final biomass and the change in abundance in both monoculture and mixture treatments. Some species in contrasting life-form groups showed compensatory dynamics, suggesting that life-form mixtures can maximize resilience of cover and biomass in the face of environmental fluctuations. This study confirms that plant traits can be used to predict growth performance in green roof ecosystems. While rapid canopy growth is desirable for green roofs, maintenance of species diversity may require engineering of conditions that favor less aggressive species.

Bioprotection and disturbance: Seaweed, microclimatic stability and conditions for mechanical weathering in the intertidal zone

NASA Astrophysics Data System (ADS)

Coombes, Martin A.; Naylor, Larissa A.; Viles, Heather A.; Thompson, Richard C.

2013-11-01

As well as their destructive roles, plants, animals and microorganisms contribute to geomorphology and ecology via direct and indirect bioprotection, which can reduce weathering and erosion. For example, indirect bioprotection can operate via biotic influences on microclimate whereby physical decay processes associated with fluctuations in temperature and moisture (salt crystallization, thermal fatigue and wetting-drying), are limited. In the intertidal zone, the spatial and temporal distribution of macroalgae (seaweeds) is patchy, related to physical and ecological conditions for colonization and growth, and the nature and frequency of natural and anthropogenic disturbance. We examined the influence of seaweed canopies (Fucus spp.) on near-surface microclimate and, by implication, on conditions for mechanical rock decay and under-canopy ecology. Monitoring on hard artificial coastal structures in South West England, UK, built from limestone and concrete showed that both the range and maxima of daily summertime temperatures were significantly lower, by an average of 56% and 25%, respectively, in areas colonized by seaweed compared to experimentally cleared areas. Short-term microclimatic variability (minutes-hours) was also significantly reduced, by an average of 78% for temperature and 71% for humidity, under algal canopies during low-tide events. Using seaweed as an example, we develop a conceptual model of the relationship between biological cover and microclimate in the intertidal zone. Disturbance events that remove or drastically reduce seaweed cover mediate shifts between relatively stable and unstable states with respect to mechanical decay and ecological stress associated with heat and desiccation. In urban coastal environments where disturbance may be frequent, facilitating the establishment and recovery of canopy-forming species on rocks and engineered structures could enhance the durability of construction materials as well as support conservation, planning and policy targets for biodiversity enhancement.

A new scheme for urban impervious surface classification from SAR images

NASA Astrophysics Data System (ADS)

Zhang, Hongsheng; Lin, Hui; Wang, Yunpeng

2018-05-01

Urban impervious surfaces have been recognized as a significant indicator for various environmental and socio-economic studies. There is an increasingly urgent demand for timely and accurate monitoring of the impervious surfaces with satellite technology from local to global scales. In the past decades, optical remote sensing has been widely employed for this task with various techniques. However, there are still a range of challenges, e.g. handling cloud contamination on optical data. Therefore, the Synthetic Aperture Radar (SAR) was introduced for the challenging task because it is uniquely all-time- and all-weather-capable. Nevertheless, with an increasing number of SAR data applied, the methodology used for impervious surfaces classification remains unchanged from the methods used for optical datasets. This shortcoming has prevented the community from fully exploring the potential of using SAR data for impervious surfaces classification. We proposed a new scheme that is comparable to the well-known and fundamental Vegetation-Impervious surface-Soil (V-I-S) model for mapping urban impervious surfaces. Three scenes of fully polarimetric Radsarsat-2 data for the cities of Shenzhen, Hong Kong and Macau were employed to test and validate the proposed methodology. Experimental results indicated that the overall accuracy and Kappa coefficient were 96.00% and 0.8808 in Shenzhen, 93.87% and 0.8307 in Hong Kong and 97.48% and 0.9354 in Macau, indicating the applicability and great potential of the new scheme for impervious surfaces classification using polarimetric SAR data. Comparison with the traditional scheme indicated that this new scheme was able to improve the overall accuracy by up to 4.6% and Kappa coefficient by up to 0.18.

Strategic guidelines for street canyon geometry to achieve sustainable street air quality

NASA Astrophysics Data System (ADS)

Chan, Andy T.; So, Ellen S. P.; Samad, Subash C.

This paper is concerned with the motion of air within the urban street canyon and is directed towards a deeper understanding of pollutant dispersion with respect to various simple canyon geometries and source positions. Taking into account the present days typical urban configurations, three principal flow regimes "isolated roughness flow", "skimming flow" and "wake interference flow" (Boundary Layer Climates, 2nd edition, Methuen, London) and their corresponding pollutant dispersion characteristics are studied for various canopies aspect ratios, namely relative height ( h2/ h1), canyon height to width ratio ( h/ w) and canyon length to height ratio ( l/ h). A field-size canyon has been analyzed through numerical simulations using the standard k- ɛ turbulence closure model. It is found that the pollutant transport and diffusion is strongly dependent upon the type of flow regime inside the canyon and exchange between canyon and the above roof air. Some rules of thumbs have been established to get urban canyon geometries for efficient dispersion of pollutants.

Modeling the energy balance in Marseille: Sensitivity to roughness length parameterizations and thermal admittance

NASA Astrophysics Data System (ADS)

Demuzere, M.; De Ridder, K.; van Lipzig, N. P. M.

2008-08-01

During the ESCOMPTE campaign (Experience sur Site pour COntraindre les Modeles de Pollution atmospherique et de Transport d'Emissions), a 4-day intensive observation period was selected to evaluate the Advanced Regional Prediction System (ARPS), a nonhydrostatic meteorological mesoscale model that was optimized with a parameterization for thermal roughness length to better represent urban surfaces. The evaluation shows that the ARPS model is able to correctly reproduce temperature, wind speed, and direction for one urban and two rural measurements stations. Furthermore, simulated heat fluxes show good agreement compared to the observations, although simulated sensible heat fluxes were initially too low for the urban stations. In order to improve the latter, different roughness length parameterization schemes were tested, combined with various thermal admittance values. This sensitivity study showed that the Zilitinkevich scheme combined with and intermediate value of thermal admittance performs best.

Assessing the Impact of Asian Longhorned Beetle in Worcester, MA: Thermal Effects, Community Responses, and Future Vulnerability

NASA Astrophysics Data System (ADS)

Elmes, Arthur Francis Marett

Urban environments experience air, water, noise, and heat pollution as a consequence of their composition, structure, and function. These adverse environmental conditions, which have direct and indirect effects on human health and ecological stability, can be mitigated or partially offset by healthy and extensive urban forests. Additionally, urban trees provide a number of cultural, aesthetic, and property value benefits. However, to provide maximum ecosystem service benefits, an urban forest must be carefully planned and maintained, so that average tree lifespan is maximized and ecological vulnerability is minimized. Maximal urban forest resilience is best achieved via taxonomic and age-diversity, such that no one genus or age-cohort dominates. This diversity enhances overall urban forest resilience, which in turn facilitates maximum ecosystem service provision. The Asian Longhorned Beetle (ALB, Anoplophora glabripennis) infestation in Worcester, MA represents a case example of taxonomic monoculture vulnerability, but also an excellent opportunity to reinvest and diversify the urban forest. As a result of the ALB infestation, which was first documented in 2008, approximately 35,000 host trees were removed from residential and public property, substantially reducing urban tree canopy coverage and uncovering impervious surfaces. Chapter two quantifies this Urban Tree Canopy (UTC) loss, and shows that in loss areas Land Surface Temperature (LST) increases range from 1 - 6° C. The research investigates multi-scale effects of this relationship, particularly in the hard-hit Burncoat and Greendale neighborhoods of Worcester, MA. In response to the large quantity of UTC loss suffered due to ALB, the Massachusetts Department of Conservation and Recreation (DCR), the City of Worcester, and the Worcester Tree Initiative (WTI) have together planted over 30,000 trees, primarily via tree giveaway programs to local residents. Chapter three assesses the effectiveness of this initiative in terms of juvenile tree mortality rates - a critical indicator of long-term urban forest success. Results indicate that tree stewardship variables such as renter proportion and number of trees planted per property are strong predictors of tree mortality. Tree species was shown to be strong predictor of mortality, with ornamental trees showing lower mortality rates than shade deciduous or conifers. Finally, Chapter four investigates the potential risk of further ALB infestation in the Worcester area, using a circuit theory dispersal model, which uses an analogy with electrical circuits to predict the dispersal of random-walkers across a heterogeneous landscape. The results indicate that impervious surfaces such as roads, sidewalks, and parking lots, as well as proximity to existing trees are facilitators of ALB movement. Circuit-based dispersal maps highlight the importance of narrow dispersal corridors connecting larger areas of potential dispersal. Dispersal potential was combined with ALB habitat suitability measured with Mahalanobis typicality, yielding a hybrid map of ALB infestation risk. These map products are valuable both as contributions to the understanding of invasive species movement in novel environments, and as tools for land managers attempting to eradicate ALB, such as the USDA Animal and Plant Health Inspection Service. This dissertation investigates three elements of the ALB infestation of Worcester, providing a holistic explanation of the impacts, recovery, and vulnerability of Worcester's urban forest.

Urban-rural inequality regarding drug prescriptions in primary care facilities - a pre-post comparison of the National Essential Medicines Scheme of China.

PubMed

Yao, Qiang; Liu, Chaojie; Ferrier, J Adamm; Liu, Zhiyong; Sun, Ju

2015-07-30

To assess the impact of the National Essential Medicines Scheme (NEMS) with respect to urban-rural inequalities regarding drug prescriptions in primary care facilities. A stratified two-stage random sampling strategy was used to sample 23,040 prescriptions from 192 primary care facilities from 2009 to 2010. Difference-in-Difference (DID) analyses were performed to test the association between NEMS and urban-rural gaps in prescription patterns. Between-Group Variance and Theil Index were calculated to measure urban-rural absolute and relative disparities in drug prescriptions. The use of the Essential Medicines List (EML) achieved a compliance rate of up to 90% in both urban and rural facilities. An overall reduction of average prescription cost improved economic access to drugs for patients in both areas. However, we observed an increased urban-rural disparity in average expenditure per prescription. The rate of antibiotics and glucocorticoids prescription remained high, despite a reduced disparity between urban and rural facilities. The average incidence of antibiotic prescription increased slightly in urban facilities (62 to 63%) and reduced in rural facilities (67% to 66%). The urban-rural disparity in the use of parenteral administration (injections and infusions) increased, albeit at a high level in both areas (44%-52%). NEMS interventions are effective in reducing the overall average prescription costs. Despite the increased use of the EML, indicator performances with respect to rational drug prescribing and use remain poor and exceed the WHO/INRUD recommended cutoff values and worldwide benchmarks. There is an increased gap between urban and rural areas in the use of parenteral administration and expenditure per prescription.

Estimation of daily maximum and minimum air temperatures in urban landscapes using MODIS time series satellite data

NASA Astrophysics Data System (ADS)

Yoo, Cheolhee; Im, Jungho; Park, Seonyoung; Quackenbush, Lindi J.

2018-03-01

Urban air temperature is considered a significant variable for a variety of urban issues, and analyzing the spatial patterns of air temperature is important for urban planning and management. However, insufficient weather stations limit accurate spatial representation of temperature within a heterogeneous city. This study used a random forest machine learning approach to estimate daily maximum and minimum air temperatures (Tmax and Tmin) for two megacities with different climate characteristics: Los Angeles, USA, and Seoul, South Korea. This study used eight time-series land surface temperature (LST) data from Moderate Resolution Imaging Spectroradiometer (MODIS), with seven auxiliary variables: elevation, solar radiation, normalized difference vegetation index, latitude, longitude, aspect, and the percentage of impervious area. We found different relationships between the eight time-series LSTs with Tmax/Tmin for the two cities, and designed eight schemes with different input LST variables. The schemes were evaluated using the coefficient of determination (R2) and Root Mean Square Error (RMSE) from 10-fold cross-validation. The best schemes produced R2 of 0.850 and 0.777 and RMSE of 1.7 °C and 1.2 °C for Tmax and Tmin in Los Angeles, and R2 of 0.728 and 0.767 and RMSE of 1.1 °C and 1.2 °C for Tmax and Tmin in Seoul, respectively. LSTs obtained the day before were crucial for estimating daily urban air temperature. Estimated air temperature patterns showed that Tmax was highly dependent on the geographic factors (e.g., sea breeze, mountains) of the two cities, while Tmin showed marginally distinct temperature differences between built-up and vegetated areas in the two cities.

Conflict resolution in the zoning of eco-protected areas in fast-growing regions based on game theory.

PubMed

Lin, Jinyao; Li, Xia

2016-04-01

Zoning eco-protected areas is important for ecological conservation and environmental management. Rapid and continuous urban expansion, however, may exert negative effects on the performance of practical zoning designs. Various methods have been developed for protected area zoning, but most of them failed to consider the conflicts between urban development (for the benefit of land developers) and ecological protection (local government). Some real-world zoning schemes even have to be modified occasionally after the lengthy negotiations between the government and land developers. Therefore, our study has presented a game theory-based method to deal with this problem. Future urban expansion in the study area will be predicted by a logistic regression cellular automaton, while eco-protected areas will be delimitated using multi-objective optimization algorithm. Then, two types of conflicts between them can be resolved based on game theory, a theory of decision-making. We established a two-person dynamic game for each conflict zone. The ecological compensation mechanism was taken into account by simulating the negotiation processes between the government and land developers. A final zoning scheme can be obtained when the two sides reach agreements. The proposed method is applied to the eco-protected area zoning in Guangzhou, a fast-growing city in China. The experiments indicate that the conflicts between eco-protection and urban development will inevitably arise when using only traditional zoning methods. Based on game theory, our method can effectively resolve those conflicts, and can provide a relatively reasonable zoning scheme. This method is expected to support policy-making in environmental management and urban planning. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Urban Environment. A Teacher's Guide, Grades K-3.

ERIC Educational Resources Information Center

Busch, Phyllis S.

Sixty-three learning activities comprise this curriculum guide to conservation education designed for elementary students. The activities enable the teacher to relate the urban child's immediate environment to the ecological problems which confront our world. Four conceptual schemes are used for each of the four grades, K-3: Living things (plants,…

Evaluation of an urban land surface scheme over a tropical suburban neighborhood

NASA Astrophysics Data System (ADS)

Harshan, Suraj; Roth, Matthias; Velasco, Erik; Demuzere, Matthias

2017-07-01

The present study evaluates the performance of the SURFEX (TEB/ISBA) urban land surface parametrization scheme in offline mode over a suburban area of Singapore. Model performance (diurnal and seasonal characteristics) is investigated using measurements of energy balance fluxes, surface temperatures of individual urban facets, and canyon air temperature collected during an 11-month period. Model performance is best for predicting net radiation and sensible heat fluxes (both are slightly overpredicted during daytime), but weaker for latent heat (underpredicted during daytime) and storage heat fluxes (significantly underpredicted daytime peaks and nighttime storage). Daytime surface temperatures are generally overpredicted, particularly those containing horizontal surfaces such as roofs and roads. This result, together with those for the storage heat flux, point to the need for a better characterization of the thermal and radiative characteristics of individual urban surface facets in the model. Significant variation exists in model behavior between dry and wet seasons, the latter generally being better predicted. The simple vegetation parametrization used is inadequate to represent seasonal moisture dynamics, sometimes producing unrealistically dry conditions.

Preferences for benefit packages for community-based health insurance: an exploratory study in Nigeria.

PubMed

Onwujekwe, Obinna; Onoka, Chima; Uguru, Nkoli; Nnenna, Tasie; Uzochukwu, Benjamin; Eze, Soludo; Kirigia, Joses; Petu, Amos

2010-06-12

It is important that community-based health insurance (CBHI) schemes are designed in such a way as to ensure the relevance of the benefit packages to potential clients. Hence, this paper provides an understanding of the preferred benefit packages by different economic status groups as well as urban and rural dwellers for CBHI in Southeast Nigeria. The study took place in rural, urban and semi-urban communities of south-east Nigeria. A questionnaire was used to collect information from 3070 randomly picked household heads. Focus group discussions were used to collect qualitative data. Data was examined for links between preferences for benefit packages with SES and geographic residence of the respondents. Respondents in the rural areas and in the lower SES preferred a comprehensive benefit package which includes all inpatient, outpatient and emergencies services, while those in urban areas as well as those in the higher SES group showed a preference for benefit packages which will cover only basic disease control interventions. Equity concerns in preferences for services to be offered by the CBHI scheme should be addressed for CBHI to succeed in different contexts.

Coupled carbon-water exchange of the Amazon rain forest, II. Comparison of predicted and observed seasonal exchange of energy, CO2, isoprene and ozone at a remote site in Rondônia

NASA Astrophysics Data System (ADS)

Simon, E.; Meixner, F. X.; Rummel, U.; Ganzeveld, L.; Ammann, C.; Kesselmeier, J.

2005-04-01

A one-dimensional multi-layer scheme describing the coupled exchange of energy and CO2, the emission of isoprene and the dry deposition of ozone is applied to a rain forest canopy in southwest Amazonia. The model was constrained using mean diel cycles of micrometeorological quantities observed during two periods in the wet and dry season 1999. Predicted net fluxes and concentration profiles for both seasonal periods are compared to observations made at two nearby towers.

The predicted day- and nighttime thermal stratification of the canopy layer is consistent with observations in dense canopies. The observed and calculated net fluxes above and H2O and CO2 concentration profiles within the canopy show a good agreement. The predicted net carbon sink decreases from 2.5 t C ha-1yr-1 for wet season conditions to 1 t C ha-1yr-1 for dry season conditions, whereas observed and predicted midday Bowen ratio increases from 0.5 to 0.8. The evaluation results confirmed a seasonal variability of leaf physiological parameters, as already suggested in the companion study. The predicted midday canopy net flux of isoprene increased from 7.1 mg C m-2h-1 during the wet season to 11.4 mg C m-2h-1 during the late dry season. Applying a constant emission capacity in all canopy layers, resulted in a disagreement between observed and simulated profiles of isoprene concentrations, suggesting a smaller emission capacity of shade adapted leaves and deposition to the soil or leaf surfaces. Assuming a strong light acclimation of emission capacity, equivalent to a 66% reduction of the standard emission factor for leaves in the lower canopy, resulted in a better agreement of observed and calculated concentration profiles and a 30% reduction of the canopy net flux. The mean calculated ozone flux for dry season condition at noontime was ≍12 nmol m-2s-1, agreeing well with observed values. The corresponding deposition velocity increased from 0.8 cm s-1 to >1.6 cm s-1 in the wet season, which can not be explained by increased stomatal uptake. Considering reasonable physiological changes in stomatal regulation, the predicted value was not larger than 1.05 cm s-1. Instead, the observed fluxes could be explained with the model by decreasing the cuticular resistance to ozone deposition from 5000 to 1000 s m-1. For doubled atmospheric CO2 concentrations the model predicts a strong increase of surface temperatures (0.1-1°C) and net assimilation (22%), a considerable shift in the energy budget (≍25% decreasing transpiration and increasing sensible heat), a slight increase of isoprene emissions (10%) and a strong decrease of ozone deposition (35%).

Movement patterns of rural and suburban white-tailed deer in Massachusetts

USGS Publications Warehouse

Gaughan, C.R.; DeStefano, S.

2005-01-01

We used satellite land cover data and the program FRAGSTATS toquantify land cover types and calculate the amount of forest edge available in suburban and rural regions of northeastern and northwestern Massachusetts. Cover categories included forest cover, open canopy vegetation, and non-deer habitat. We calculated all edge segments where forest cover abutted open canopy cover. Our open canopy vegetation category was calculated both with and without low intensity suburban development. We then compared these findings to movement data from 53 (13 males, 40 females) adult radio-marked white-tailed deerOdocoileus virginianusmonitored biweekly and diurnally from January 2001 to January 2003. The range of movements of suburban deer in eastern Massachusetts showed no difference to that of suburban deer in western Massachusetts (P = 0.7). However, the ranges for suburban deer in both eastern and western Massachusetts were 10 times less than those of deer in rural western Massachusetts (P = 0.001).Our findings suggest that landscape configuration, as described by the amount and distribution of edge due to suburban development, which is related to the amount and distribution of resources such as food and cover, affects migratory behavior of white-tailed deer, allowsdeer to have smaller ranges, and contributes to high deer densities.Inclusion of suburban edge in habitat models will increase our understanding of deer-habitat relationships for management of deer in urbanizing environments. ?? 2005 Springer Science + Business Media, Inc.

Street canyon aerosol pollutant transport measurements.

PubMed

Longley, I D; Gallagher, M W; Dorsey, J R; Flynn, M; Bower, K N; Allan, J D

2004-12-01

Current understanding of dispersion in street canyons is largely derived from relatively simple dispersion models. Such models are increasingly used in planning and regulation capacities but are based upon a limited understanding of the transport of substances within a real canyon. In recent years, some efforts have been made to numerically model localised flow in idealised canyons (e.g., J. Appl. Meteorol. 38 (1999) 1576-89) and stepped canyons (Assimakopoulos V. Numerical modelling of dispersion of atmospheric pollution in and above urban canopies. PhD thesis, Imperial College, London, 2001) but field studies in real canyons are rare. To further such an understanding, a measurement campaign has been conducted in an asymmetric street canyon with busy one-way traffic in central Manchester in northern England. The eddy correlation method was used to determine fluxes of size-segregated accumulation mode aerosol. Measurements of aerosol at a static location were made concurrently with measurements on a platform lift giving vertical profiles. Size-segregated measurements of ultrafine and coarse particle concentrations were also made simultaneously at various heights. In addition, a small mobile system was used to make measurements of turbulence at various pavement locations within the canyon. From this data, various features of turbulent transport and dispersion in the canyon will be presented. The concentration and the ventilation fluxes of vehicle-related aerosol pollutants from the canyon will be related to controlling factors. The results will also be compared with citywide ventilation data from a separate measurement campaign conducted above the urban canopy.

Outcome-based health equity across different social health insurance schemes for the elderly in China.

PubMed

Liu, Xiaoting; Wong, Hung; Liu, Kai

2016-01-14

Against the achievement of nearly universal coverage for social health insurance for the elderly in China, a problem of inequity among different insurance schemes on health outcomes is still a big challenge for the health care system. Whether various health insurance schemes have divergent effects on health outcome is still a puzzle. Empirical evidence will be investigated in this study. This study employs a nationally representative survey database, the National Survey of the Aged Population in Urban/Rural China, to compare the changes of health outcomes among the elderly before and after the reform. A one-way ANOVA is utilized to detect disparities in health care expenditures and health status among different health insurance schemes. Multiple Linear Regression is applied later to examine the further effects of different insurance plans on health outcomes while controlling for other social determinants. The one-way ANOVA result illustrates that although the gaps in insurance reimbursements between the Urban Employee Basic Medical Insurance (UEBMI) and the other schemes, the New Rural Cooperative Medical Scheme (NCMS) and Urban Residents Basic Medical Insurance (URBMI) decreased, out-of-pocket spending accounts for a larger proportion of total health care expenditures, and the disparities among different insurances enlarged. Results of the Multiple Linear Regression suggest that UEBMI participants have better self-reported health status, physical functions and psychological wellbeing than URBMI and NCMS participants, and those uninsured. URBMI participants report better self-reported health than NCMS ones and uninsured people, while having worse psychological wellbeing compared with their NCMS counterparts. This research contributes to a transformation in health insurance studies from an emphasis on the opportunity-oriented health equity measured by coverage and healthcare accessibility to concern with outcome-based equity composed of health expenditure and health status. The results indicate that fragmented health insurance schemes generate inequitable health care utilization and health outcomes for the elderly. This study re-emphasizes the importance of reforming health insurance systems based on their health outcome rather than entitlement, which will particularly benefit the most vulnerable older groups.

Seasonality on the rainfall partitioning of a fast-growing tree plantation under Mediterranean conditions

NASA Astrophysics Data System (ADS)

molina, antonio; llorens, pilar; biel, carme

2014-05-01

Studies on rainfall interception in fast-growing tree plantations are less numerous than those in natural forests. Trees in these plantations are regularly distributed, and the canopy cover is clumped but changes quickly, resulting on high variability in the volume and composition of water that reach the soil. In addition, irrigation supply is normally required in semiarid areas to get optimal wood production; consequently, knowing rainfall interception and its yearly evolution is crucial to manage the irrigation scheme properly. This work studies the rainfall partitioning seasonality in a cherry tree (Prunus avium) plantation orientated to timber production under Mediterranean conditions. The monitoring design started on March 2012 and consists of a set of 58 throughfall tipping buckets randomly distributed (based on a 1x1 m2 grid) in a plot of 128 m2 with 8 trees. Stemflow is measured in all the trees with 2 tipping buckets and 6 accumulative collectors. Canopy cover is regularly measured throughout the study period, in leaf and leafless periods, by mean of sky-orientated photographs taken 50 cm above the center of each tipping bucket. Others tree biometrics are also measured such as diameter and leaf area index. Meteorological conditions are measured at 2 m above the forest cover. This work presents the first analyses describing the rainfall partitioning and its dependency on canopy cover, distance to tree and meteorological conditions. The modified Gash' model for rainfall interception in dispersed vegetation is also preliminary evaluated.

Classification of Tree Species in Overstorey Canopy of Subtropical Forest Using QuickBird Images.

PubMed

Lin, Chinsu; Popescu, Sorin C; Thomson, Gavin; Tsogt, Khongor; Chang, Chein-I

2015-01-01

This paper proposes a supervised classification scheme to identify 40 tree species (2 coniferous, 38 broadleaf) belonging to 22 families and 36 genera in high spatial resolution QuickBird multispectral images (HMS). Overall kappa coefficient (OKC) and species conditional kappa coefficients (SCKC) were used to evaluate classification performance in training samples and estimate accuracy and uncertainty in test samples. Baseline classification performance using HMS images and vegetation index (VI) images were evaluated with an OKC value of 0.58 and 0.48 respectively, but performance improved significantly (up to 0.99) when used in combination with an HMS spectral-spatial texture image (SpecTex). One of the 40 species had very high conditional kappa coefficient performance (SCKC ≥ 0.95) using 4-band HMS and 5-band VIs images, but, only five species had lower performance (0.68 ≤ SCKC ≤ 0.94) using the SpecTex images. When SpecTex images were combined with a Visible Atmospherically Resistant Index (VARI), there was a significant improvement in performance in the training samples. The same level of improvement could not be replicated in the test samples indicating that a high degree of uncertainty exists in species classification accuracy which may be due to individual tree crown density, leaf greenness (inter-canopy gaps), and noise in the background environment (intra-canopy gaps). These factors increase uncertainty in the spectral texture features and therefore represent potential problems when using pixel-based classification techniques for multi-species classification.

Climatic and biotic drivers of tropical evergreen forest photosynthesis: integrating field, eddy flux, remote sensing and modelling

NASA Astrophysics Data System (ADS)

Wu, J.; Serbin, S.; Xu, X.; Guan, K.; Albert, L.; Hayek, M.; Restrepo-Coupe, N.; Lopes, A. P.; Wiedemann, K. T.; Christoffersen, B. O.; Meng, R.; De Araujo, A. C.; Oliveira Junior, R. C.; Camargo, P. B. D.; Silva, R. D.; Nelson, B. W.; Huete, A. R.; Rogers, A.; Saleska, S. R.

2016-12-01

Tropical evergreen forest photosynthetic metabolism is an important driver of large-scale carbon, water, and energy cycles, generating various climate feedbacks. However, considerable uncertainties remain regarding how best to represent evergreen forest photosynthesis in current terrestrial biosphere models (TBMs), especially its sensitivity to climatic vs. biotic variation. Here, we develop a new approach to partition climatic and biotic controls on tropical forest photosynthesis from hourly to inter-annual timescales. Our results show that climatic factors dominate photosynthesis dynamics at shorter-time scale (i.e. hourly), while biotic factors dominate longer-timescale (i.e. monthly and longer) photosynthetic dynamics. Focusing on seasonal timescales, we combine camera and ecosystem carbon flux observations of forests across a rainfall gradient in Amazonia to show that high dry season leaf turnover shifts canopy composition towards younger more efficient leaves. This seasonal variation in leaf quality (per-area leaf photosynthetic capacity) thus can explain the high photosynthetic seasonality observed in the tropics. Finally, we evaluated the performance of models with different phenological schemes (i.e. leaf quantity versus leaf quality; with and without leaf phenological variation alone the vertical canopy profile). We found that models which represented the phenology of leaf quality and its within-canopy variation performed best in simulating photosynthetic seasonality in tropical evergreen forests. This work highlights the importance of incorporating improved understanding of climatic and biotic controls in next generation TBMs to project future carbon and water cycles in the tropics.

Ecological connectivity in the three-dimensional urban green volume using waveform airborne lidar

PubMed Central

Casalegno, Stefano; Anderson, Karen; Cox, Daniel T. C.; Hancock, Steven; Gaston, Kevin J.

2017-01-01

The movements of organisms and the resultant flows of ecosystem services are strongly shaped by landscape connectivity. Studies of urban ecosystems have relied on two-dimensional (2D) measures of greenspace structure to calculate connectivity. It is now possible to explore three-dimensional (3D) connectivity in urban vegetation using waveform lidar technology that measures the full 3D structure of the canopy. Making use of this technology, here we evaluate urban greenspace 3D connectivity, taking into account the full vertical stratification of the vegetation. Using three towns in southern England, UK, all with varying greenspace structures, we describe and compare the structural and functional connectivity using both traditional 2D greenspace models and waveform lidar-generated vegetation strata (namely, grass, shrubs and trees). Measures of connectivity derived from 3D greenspace are lower than those derived from 2D models, as the latter assumes that all vertical vegetation strata are connected, which is rarely true. Fragmented landscapes that have more complex 3D vegetation showed greater functional connectivity and we found highest 2D to 3D functional connectivity biases for short dispersal capacities of organisms (6 m to 16 m). These findings are particularly pertinent in urban systems where the distribution of greenspace is critical for delivery of ecosystem services. PMID:28382936

Ecological connectivity in the three-dimensional urban green volume using waveform airborne lidar

NASA Astrophysics Data System (ADS)

Casalegno, Stefano; Anderson, Karen; Cox, Daniel T. C.; Hancock, Steven; Gaston, Kevin J.

2017-04-01

The movements of organisms and the resultant flows of ecosystem services are strongly shaped by landscape connectivity. Studies of urban ecosystems have relied on two-dimensional (2D) measures of greenspace structure to calculate connectivity. It is now possible to explore three-dimensional (3D) connectivity in urban vegetation using waveform lidar technology that measures the full 3D structure of the canopy. Making use of this technology, here we evaluate urban greenspace 3D connectivity, taking into account the full vertical stratification of the vegetation. Using three towns in southern England, UK, all with varying greenspace structures, we describe and compare the structural and functional connectivity using both traditional 2D greenspace models and waveform lidar-generated vegetation strata (namely, grass, shrubs and trees). Measures of connectivity derived from 3D greenspace are lower than those derived from 2D models, as the latter assumes that all vertical vegetation strata are connected, which is rarely true. Fragmented landscapes that have more complex 3D vegetation showed greater functional connectivity and we found highest 2D to 3D functional connectivity biases for short dispersal capacities of organisms (6 m to 16 m). These findings are particularly pertinent in urban systems where the distribution of greenspace is critical for delivery of ecosystem services.

The Budget of Turbulent Kinetic Energy in the Urban Roughness Sublayer

NASA Astrophysics Data System (ADS)

Christen, Andreas; Rotach, Mathias W.; Vogt, Roland

2009-05-01

Full-scale observations from two urban sites in Basel, Switzerland were analysed to identify the magnitude of different processes that create, relocate, and dissipate turbulent kinetic energy (TKE) in the urban atmosphere. Two towers equipped with a profile of six ultrasonic anemometers each sampled the flow in the urban roughness sublayer, i.e. from street canyon base up to roughly 2.5 times the mean building height. This observational study suggests a conceptual division of the urban roughness sublayer into three layers: (1) the layer above the highest roofs, where local buoyancy production and local shear production of TKE are counterbalanced by local viscous dissipation rate and scaled turbulence statistics are close to to surface-layer values; (2) the layer around mean building height with a distinct inflexional mean wind profile, a strong shear and wake production of TKE, a more efficient turbulent exchange of momentum, and a notable export of TKE by transport processes; (3) the lower street canyon with imported TKE by transport processes and negligible local production. Averaged integral velocity variances vary significantly with height in the urban roughness sublayer and reflect the driving processes that create or relocate TKE at a particular height. The observed profiles of the terms of the TKE budget and the velocity variances show many similarities to observations within and above vegetation canopies.

Urban-area extraction from polarimetric SAR image using combination of target decomposition and orientation angle

NASA Astrophysics Data System (ADS)

Zou, Bin; Lu, Da; Wu, Zhilu; Qiao, Zhijun G.

2016-05-01

The results of model-based target decomposition are the main features used to discriminate urban and non-urban area in polarimetric synthetic aperture radar (PolSAR) application. Traditional urban-area extraction methods based on modelbased target decomposition usually misclassified ground-trunk structure as urban-area or misclassified rotated urbanarea as forest. This paper introduces another feature named orientation angle to improve urban-area extraction scheme for the accurate mapping in urban by PolSAR image. The proposed method takes randomness of orientation angle into account for restriction of urban area first and, subsequently, implements rotation angle to improve results that oriented urban areas are recognized as double-bounce objects from volume scattering. ESAR L-band PolSAR data of the Oberpfaffenhofen Test Site Area was used to validate the proposed algorithm.

Controlled-release Hydrogen Peroxide for On-site Treatment of Organic Pollutants in Urban Storm Runoff

NASA Astrophysics Data System (ADS)

Lee, E.; Sun, S.; Kim, Y.

2011-12-01

Nonpoint source (NPS) pollutants are the remaining cause of the environment problems, significantly impairing the hydrologic and biologic function of urban water systems and human health. Managing the NPS loads to urban aquatic systems remains a challenge because of ubiquitous contaminant sources and large pollutants loads in the first flush. Best management practices (BMPs) exist for reducing the NPS pollutants in urban storm waters, but the remedial efficiencies of these passive schemes are unpredictable. This study aims to develop a controlled-release system as part of an in situ chemical oxidation scheme designed for on-site treatment of organic pollutants in urban runoff. Controlled-release hydrogen peroxide (CR-HP) solids were manufactured by dispersing fine sodium percarbonate granules in paraffin wax matrices. Release kinetics and treatment efficiencies of CR-HP for BTEX and MTBE were investigated through a series of column tests. Release data indicated that the CR-HP could continually release hydrogen peroxide (H2O2) in flowing water at controlled rates over 276-1756 days, and the release rates could be adjusted by changing the mixing ratios of sodium percarbonate and wax matrices. Additional column tests and model calculations demonstrated that CR-HP/UV systems can provide low-cost, target-specific, and persistent source of oxidants for efficient treatment of organic compounds in urban storm runoff.

Costs, equity, efficiency and feasibility of identifying the poor in Ghana's National Health Insurance Scheme: empirical analysis of various strategies.

PubMed

Aryeetey, Genevieve Cecilia; Jehu-Appiah, Caroline; Spaan, Ernst; Agyepong, Irene; Baltussen, Rob

2012-01-01

To analyse the costs and evaluate the equity, efficiency and feasibility of four strategies to identify poor households for premium exemptions in Ghana's National Health Insurance Scheme (NHIS): means testing (MT), proxy means testing (PMT), participatory wealth ranking (PWR) and geographic targeting (GT) in urban, rural and semi-urban settings in Ghana. We conducted the study in 145-147 households per setting with MT as our gold standard strategy. We estimated total costs that included costs of household surveys and cost of premiums paid to the poor, efficiency (cost per poor person identified), equity (number of true poor excluded) and the administrative feasibility of implementation. The cost of exempting one poor individual ranged from US$15.87 to US$95.44; exclusion of the poor ranged between 0% and 73%. MT was most efficient and equitable in rural and urban settings with low-poverty incidence; GT was efficient and equitable in the semi-urban setting with high-poverty incidence. PMT and PWR were less equitable and inefficient although feasible in some settings. We recommend MT as optimal strategy in low-poverty urban and rural settings and GT as optimal strategy in high-poverty semi-urban setting. The study is relevant to other social and developmental programmes that require identification and exemptions of the poor in low-income countries. © 2011 Blackwell Publishing Ltd.

Atmospheric pollutants in peri-urban forests of Quercus ilex: evidence of pollution abatement and threats for vegetation.

PubMed

García-Gómez, Héctor; Aguillaume, Laura; Izquieta-Rojano, Sheila; Valiño, Fernando; Àvila, Anna; Elustondo, David; Santamaría, Jesús M; Alastuey, Andrés; Calvete-Sogo, Héctor; González-Fernández, Ignacio; Alonso, Rocío

2016-04-01

Peri-urban vegetation is generally accepted as a significant remover of atmospheric pollutants, but it could also be threatened by these compounds, with origin in both urban and non-urban areas. To characterize the seasonal and geographical variation of pollutant concentrations and to improve the empirical understanding of the influence of Mediterranean broadleaf evergreen forests on air quality, four forests of Quercus ilex (three peri-urban and one remote) were monitored in different areas in Spain. Concentrations of nitrogen dioxide (NO2), ammonia (NH3), nitric acid (HNO3) and ozone (O3) were measured during 2 years in open areas and inside the forests and aerosols (PM10) were monitored in open areas during 1 year. Ozone was the only air pollutant expected to have direct phytotoxic effects on vegetation according to current thresholds for the protection of vegetation. The concentrations of N compounds were not high enough to directly affect vegetation but could be contributing through atmospheric N deposition to the eutrophization of these ecosystems. Peri-urban forests of Q. ilex showed a significant below-canopy reduction of gaseous concentrations (particularly NH3, with a mean reduction of 29-38%), which indicated the feasibility of these forests to provide an ecosystem service of air quality improvement. Well-designed monitoring programs are needed to further investigate air quality improvement by peri-urban ecosystems while assessing the threat that air pollution can pose to vegetation.

Interactions between Cool Roofs and Urban Irrigation: Do Cooling Strategies Reduce Water Consumption in the San Francisco Bay Area?

NASA Astrophysics Data System (ADS)

Vahmani, P.; Jones, A. D.

2016-12-01

California has experienced progressive drought since 2012, with 2012-2014 constituting a nearly 10,000-year drought event, resulting in a suite of policies with the goal of reducing water consumption. At the same time, climate warming effects of accelerated urbanization along with projected global climate change raise an urgent need for sustainable mitigation and adaptation strategies to cool urban climates. In this study, for the first time, we assess the overarching benefits of cooling strategies on urban water consumption. We employ a satellite-supported regional climate-modeling framework over the San Francisco Bay Area to assess the effects of cool roofs on urban irrigation, a topic of increasing importance as it accounts for a significant fraction of urban water use particularly in arid and semi-arid regions. We use a suit of climatological simulations at high (1.5 km) spatial resolution, based on a Weather Research and Forecasting (WRF)-Urban Canopy Model (UCM) modeling framework, reinforced with remotely sensed observations of Green Vegetation Fraction (GVF), leaf area index (LAI), and albedo. Our analysis shows that widespread incorporation of cool roofs would result in a mean daytime cooling of about 0.7° C, which in turn results in roughly 4% reduction in irrigation water, largely due to decreases in surface evapotranspiration rates. We further investigate the critical interactions between cool roofs, wind, and sea-breeze patterns as well as fog formation, a dominant weather pattern in San Francisco Bay area.

Mapping urban porosity and roughness characteristics as a mean of defining urban ventilation corridors

NASA Astrophysics Data System (ADS)

Wicht, Marzena; Wicht, Andreas; Osińska-Skotak, Katarzyna

2017-10-01

Cities can be characterized with the roughest aerodynamic boundaries, which results in the enhanced turbulent motion and increased drag effect. This leads to reduced wind speeds and directly increases negative effects of living within urban areas. Urban Heat Island, decreased air quality or densely built-up residential/industrial areas occur in many cities, both in temperate and tropical regions, and are included in these negative effects. This case study investigates Warsaw, the capital of Poland, representing a dense, urban environment, located in the temperate zone. It suffers from immense air pollution levels, as well as Urban Heat Island, and the local government is seeking ways to resolve these issues. Among many mitigation techniques, air restoration and exchange system were suggested as appropriate measures, as they address many of the aforementioned issues. The essential elements of such system are ventilation corridors. This paper describes mapping these corridors utilizing the morphometric methods of urban roughness aided by remote sensing data. We focus especially on the terrain topology and texture of single elements, including high vegetation canopy layer. This study considers DSM and different porosity of obstacles, deriving a new outlook at the morphometric methods as a way to improve them. The mapped areas of low roughness characteristics might be appointed as ventilation corridors and play a crucial role in air restoration and exchange system. They may also be included in further planning processes by the local government as preservation areas.

A numerical study of the effect of urbanization on the climate of Las Vegas metropolitan area

NASA Astrophysics Data System (ADS)

Kamal, S. M.; Huang, H. P.; Myint, S. W.

2014-12-01

Las Vegas is one of the fastest growing desert cities. Its developed area has doubled in the last 30 years. An accurate prediction of the effect of urbanization on the climate of the city is crucial for resource management and planning. In this study, we use the Weather Research and Forecasting (WRF) model coupled with a land surface and urban canopy model to investigate the effects of urbanization on the regional climate pattern around Las Vegas. High resolution numerical simulations are performed with a 3 km resolution over the metropolitan area. With identical lateral boundary conditions, three land-use land-cover maps, representing 2006, 1992 and hypothetical 1900, are used in multiple simulations. The differences in the simulated climate among those cases are used to quantify the urban effect. The simulated surface air temperature is validated against observational data from the weather station at the McCarran airport. It is found that urbanization affects substantial warming during the night but a minor cooling during the day. Detailed diagnostics of the surface energy budget are performed to help interpret this result. In addition, the emerging urban structures are found to have a mechanical effect of slowing down the climatological wind field over the urban area. The change in wind, in turn, leads to a secondary modification of the temperature structure within the air shed of the city. This finding suggests the need to combine the mechanical and thermodynamic effects to construct a complete picture of the influence of land cover on urban climate. In all cases of the simulations, it is also demonstrated that urbanization influences surface air temperature mainly within the metropolitan area.

Spatial and temporal land cover changes in Terminos Lagoon Reserve, Mexico.

PubMed

Soto-Galera, Ernesto; Piera, Jaume; López, Pilar

2010-06-01

Terminos Lagoon ecosystem is the largest fluvial-lagoon estuarine system in the country and one of the most important reserves of coastal flora and fauna in Mexico. Since the seventies, part of the main infrastructure for country's oil extraction is located in this area. Its high biodiversity has motivated different type of studies including deforestation processes and land use planning. In this work we used satellite image analysis to determine land cover changes in the area from 1974 to 2001. Our results indicate that tropical forest and mangroves presented the most extensive losses in its coverage. In contrast, urban areas and induced grassland increased considerably. In 2001 more than half of the ecosystem area showed changes from its original land cover, and a third part of it was deteriorated. The main causes of deforestation were both the increase in grassland and the growth of urban areas. However, deforestation was attenuated by natural reforestation and plant canopy recovery. We conclude that the introduction of cattle and urban development were the main causes for the land cover changes; however, the oil industry activity located in the ecosystem, has promoted indirectly to urban growth and rancher boom.

Assessing measurement uncertainty in meteorology in urban environments

NASA Astrophysics Data System (ADS)

Curci, S.; Lavecchia, C.; Frustaci, G.; Paolini, R.; Pilati, S.; Paganelli, C.

2017-10-01

Measurement uncertainty in meteorology has been addressed in a number of recent projects. In urban environments, uncertainty is also affected by local effects which are more difficult to deal with than for synoptic stations. In Italy, beginning in 2010, an urban meteorological network (Climate Network®) was designed, set up and managed at national level according to high metrological standards and homogeneity criteria to support energy applications. The availability of such a high-quality operative automatic weather station network represents an opportunity to investigate the effects of station siting and sensor exposure and to estimate the related measurement uncertainty. An extended metadata set was established for the stations in Milan, including siting and exposure details. Statistical analysis on an almost 3-year-long operational period assessed network homogeneity, quality and reliability. Deviations from reference mean values were then evaluated in selected low-gradient local weather situations in order to investigate siting and exposure effects. In this paper the methodology is depicted and preliminary results of its application to air temperature discussed; this allowed the setting of an upper limit of 1 °C for the added measurement uncertainty at the top of the urban canopy layer.

A multi-resolution ensemble study of a tropical urban environment and its interactions with the background regional atmosphere

NASA Astrophysics Data System (ADS)

Li, Xian-Xiang; Koh, Tieh-Yong; Entekhabi, Dara; Roth, Matthias; Panda, Jagabandhu; Norford, Leslie K.

2013-09-01

This study employed the Weather Research and Forecasting model with a single-layer urban canopy model to investigate the urban environment of a tropical city, Singapore. The coupled model was evaluated against available observational data from a sensor network and flux tower. The effects of land use type and anthropogenic heat (AH) on the thermal and wind environment were investigated with a series of sensitivity tests using an ensemble approach for low advection, high convective available potential energy, intermonsoon season cases. The diurnal cycle and spatial pattern of urban heat island (UHI) intensity and planetary boundary layer height were investigated. The mean UHI intensity peaked in the early morning at 2.2°C, reaching 2.4°C in industrial areas. Sea and land breezes developed during daytime and nighttime, respectively, with the former much stronger than the latter. The model predicted that sea breezes from different coastlines of the Malay Peninsula meet and converge, inducing strong updrafts. AH was found to play roles in all the processes studied, while the effect of different land use types was most pronounced during nighttime, and least visible near noon.

Multi-scale modelling to evaluate building energy consumption at the neighbourhood scale.

PubMed

Mauree, Dasaraden; Coccolo, Silvia; Kaempf, Jérôme; Scartezzini, Jean-Louis

2017-01-01

A new methodology is proposed to couple a meteorological model with a building energy use model. The aim of such a coupling is to improve the boundary conditions of both models with no significant increase in computational time. In the present case, the Canopy Interface Model (CIM) is coupled with CitySim. CitySim provides the geometrical characteristics to CIM, which then calculates a high resolution profile of the meteorological variables. These are in turn used by CitySim to calculate the energy flows in an urban district. We have conducted a series of experiments on the EPFL campus in Lausanne, Switzerland, to show the effectiveness of the coupling strategy. First, measured data from the campus for the year 2015 are used to force CIM and to evaluate its aptitude to reproduce high resolution vertical profiles. Second, we compare the use of local climatic data and data from a meteorological station located outside the urban area, in an evaluation of energy use. In both experiments, we demonstrate the importance of using in building energy software, meteorological variables that account for the urban microclimate. Furthermore, we also show that some building and urban forms are more sensitive to the local environment.

Multi-scale modelling to evaluate building energy consumption at the neighbourhood scale

PubMed Central

Coccolo, Silvia; Kaempf, Jérôme; Scartezzini, Jean-Louis

2017-01-01

A new methodology is proposed to couple a meteorological model with a building energy use model. The aim of such a coupling is to improve the boundary conditions of both models with no significant increase in computational time. In the present case, the Canopy Interface Model (CIM) is coupled with CitySim. CitySim provides the geometrical characteristics to CIM, which then calculates a high resolution profile of the meteorological variables. These are in turn used by CitySim to calculate the energy flows in an urban district. We have conducted a series of experiments on the EPFL campus in Lausanne, Switzerland, to show the effectiveness of the coupling strategy. First, measured data from the campus for the year 2015 are used to force CIM and to evaluate its aptitude to reproduce high resolution vertical profiles. Second, we compare the use of local climatic data and data from a meteorological station located outside the urban area, in an evaluation of energy use. In both experiments, we demonstrate the importance of using in building energy software, meteorological variables that account for the urban microclimate. Furthermore, we also show that some building and urban forms are more sensitive to the local environment. PMID:28880883

Disparity in reimbursement for tuberculosis care among different health insurance schemes: evidence from three counties in central China.

PubMed

Pan, Yao; Chen, Shanquan; Chen, Manli; Zhang, Pei; Long, Qian; Xiang, Li; Lucas, Henry

2016-01-27

Health inequity is an important issue all around the world. The Chinese basic medical security system comprises three major insurance schemes, namely the Urban Employee Basic Medical Insurance (UEBMI), the Urban Resident Basic Medical Insurance (URBMI), and the New Cooperative Medical Scheme (NCMS). Little research has been conducted to look into the disparity in payments among the health insurance schemes in China. In this study, we aimed to evaluate the disparity in reimbursements for tuberculosis (TB) care among the abovementioned health insurance schemes. This study uses a World Health Organization (WHO) framework to analyze the disparities and equity relating to the three dimensions of health insurance: population coverage, the range of services covered, and the extent to which costs are covered. Each of the health insurance scheme's policies were categorized and analyzed. An analysis of the claims database of all hospitalizations reimbursed from 2010 to 2012 in three counties of Yichang city (YC), which included 1506 discharges, was conducted to identify the differences in reimbursement rates and out-of-pocket (OOP) expenses among the health insurance schemes. Tuberculosis patients had various inpatient expenses depending on which scheme they were covered by (TB patients covered by the NCMS have less inpatient expenses than those who were covered by the URBMI, who have less inpatient expenses than those covered by the UEBMI). We found a significant horizontal inequity of healthcare utilization among the lower socioeconomic groups. In terms of financial inequity, TB patients who earned less paid more. The NCMS provides modest financial protection, based on income. Overall, TB patients from lower socioeconomic groups were the most vulnerable. There are large disparities in reimbursement for TB care among the three health insurance schemes and this, in turn, hampers TB control. Reducing the gap in health outcomes between the three health insurance schemes in China should be a focus of TB care and control. Achieving equity through integrated policies that avoid discrimination is likely to be effective.

Investigating Land-Use Effects on Hydrologic Processes and Water Quality in a Complex Karst Hydro-Region of the Central United States

NASA Astrophysics Data System (ADS)

Hubbart, J. A.; Bulliner, E. A.; Freeman, G. W.; Chinnasamy, P.; Hosmer, G. W.; Scollan, D. P.; Stokely, T. D.

2009-12-01

A century of watershed studies verify that hydrologic and water quality responses to land-use varies substantially physiographically. In the Oak dominated, Missouri Ozark Karst hydrogeologic region of the Central U.S., catchment studies are needed to validate current forest best management practices (BMPs). Similarly, studies are necessary that quantify urban degraded freshwater resources and disassembled riparian zone form and function. Given that continued human population growth over the next several decades will place unprecedented demands on forested and urban water resources, it is imperative to confront contemporary forested watershed issues that encompass the wildland - urban interface. Studies were initiated in the fall of 2008 to: a) validate current riparian forest BMPs, b) quantify peak flows and microclimate alteration due to urbanization, and c) quantify stream connectivity to adjacent riparian floodplains. Study catchments are located in the urbanizing Hinkson Creek Watershed (HCW, 231km2) and the Baskett Wildlife Research and Education Area (BREA, 8.9 km2), both watersheds centrally located in Missouri. Hydroclimate stations were installed at five locations along Hinkson Creek partitioning forest, cropland, and urban environments (nested-scale study design), and two opposing forested stream reaches of the BREA. Climate in central Missouri is generally classified as humid continental, with annual mean temperature and precipitation of approximately 12.6 °C and 1050 mm respectively. Study catchments land use spans old growth mixed deciduous forest to rural pastureland and the growing urbanized center of Columbia, Mo (population exceeding 101,000). Soils are highly variable prairie-forest transitional to loamy till with a well developed clay pan of thin cherty clay and silty to sandy clay. Preliminary analyses of BREA riparian data (summer 2009) indicate that average temperatures for E-W oriented stream reaches are 0.3 °C lower than the N-S reaches and 2.2 °C lower than climate reference sites, reflecting the effects of canopy layers, density, and landscape physiography. Average net shortwave radiation for N-S oriented reach was 3.2% higher than the E-W reach, while maximum net longwave radiation was 62.4% lower. These results may hold important implications for on-going surface energy balance computations assessing canopy influence on stream water temperature. Preliminary analyses of HCW flow data indicate that forested headwater systems better attenuate peak flows of small precipitation events (< 0.80 mm) relative to current urban capabilities. Precipitation events greater than 1.0 mm result in peak rainfall time to peak flow decreased by as much as 13% in urban settings accompanied by at least 4 cm higher stage and 5 to 10% greater flow volume. Average air temperature in urbanized Columbia can exceed the forested region by as much as 15%, and precipitation events can be 50% greater in magnitude. Results from these complimentary studies will produce necessary datasets to improve hydrologic process understanding and develop improved guidelines and management tools in complex hydrophysiographic regions of Missouri and the Central U.S.

Modeling the Surface Energy Balance of the Core of an Old Mediterranean City: Marseille.

NASA Astrophysics Data System (ADS)

Lemonsu, A.; Grimmond, C. S. B.; Masson, V.

2004-02-01

The Town Energy Balance (TEB) model, which parameterizes the local-scale energy and water exchanges between urban surfaces and the atmosphere by treating the urban area as a series of urban canyons, coupled to the Interactions between Soil, Biosphere, and Atmosphere (ISBA) scheme, was run in offline mode for Marseille, France. TEB's performance is evaluated with observations of surface temperatures and surface energy balance fluxes collected during the field experiments to constrain models of atmospheric pollution and transport of emissions (ESCOMPTE) urban boundary layer (UBL) campaign. Particular attention was directed to the influence of different surface databases, used for input parameters, on model predictions. Comparison of simulated canyon temperatures with observations resulted in improvements to TEB parameterizations by increasing the ventilation. Evaluation of the model with wall, road, and roof surface temperatures gave good results. The model succeeds in simulating a sensible heat flux larger than heat storage, as observed. A sensitivity comparison using generic dense city parameters, derived from the Coordination of Information on the Environment (CORINE) land cover database, and those from a surface database developed specifically for the Marseille city center shows the importance of correctly documenting the urban surface. Overall, the TEB scheme is shown to be fairly robust, consistent with results from previous studies.

Estimating accidental pollutant releases in the built environment from turbulent concentration signals

NASA Astrophysics Data System (ADS)

Ben Salem, N.; Salizzoni, P.; Soulhac, L.

2017-01-01

We present an inverse atmospheric model to estimate the mass flow rate of an impulsive source of pollutant, whose position is known, from concentration signals registered at receptors placed downwind of the source. The originality of this study is twofold. Firstly, the inversion is performed using high-frequency fluctuating, i.e. turbulent, concentration signals. Secondly, the inverse algorithm is applied to a dispersion process within a dense urban canopy, at the district scale, and a street network model, SIRANERISK, is adopted. The model, which is tested against wind tunnel experiments, simulates the dispersion of short-duration releases of pollutant in different typologies of idealised urban geometries. Results allow us to discuss the reliability of the inverse model as an operational tool for crisis management and the risk assessments related to the accidental release of toxic and flammable substances.

Developing a global mixed-canopy, height-variable vegetation structure dataset for estimating global vegetation albedo by a clumped canopy radiative transfer scheme in the NASA Ent Terrestrial Biosphere Model and GISS GCM

NASA Astrophysics Data System (ADS)

Montes, Carlo; Kiang, Nancy Y.; Ni-Meister, Wenge; Yang, Wenze; Schaaf, Crystal; Aleinov, Igor; Jonas, Jeffrey A.; Zhao, Feng; Yao, Tian; Wang, Zhuosen; Sun, Qingsong; Carrer, Dominique

2016-04-01

Processes determining biosphere-atmosphere coupling are strongly influenced by vegetation structure. Thus, ecosystem carbon sequestration and evapotranspiration affecting global carbon and water balances will depend upon the spatial extent of vegetation, its vertical structure, and its physiological variability. To represent this globally, Dynamic Global Vegetation Models (DGVMs) coupled to General Circulation Models (GCMs) make use of satellite and/or model-based vegetation classifications often composed by homogeneous communities. This work aims at developing a new Global Vegetation Structure Dataset (GVSD) by incorporating varying vegetation heights for mixed plant communities to be used as boundary conditions to the Analytical Clumped Two-Stream (ACTS) canopy radiative transfer scheme (Ni-Meister et al., 2010) incorporated into the NASA Ent Terrestrial Biosphere Model (TBM), the DGVM coupled to the NASA Goddard Institute for Space Studies (GISS) GCM. Information sources about land surface and vegetation characteristics obtained from a number of earth observation platforms and algorithms include the Moderate Resolution Imaging Spectroradiometer (MODIS) land cover and plant functional types (PFTs) (Friedl et al., 2010), soil albedo derived from MODIS (Carrer et al., 2014), along with vegetation height from the Geoscience Laser Altimeter System (GLAS) on board ICESat (Ice, Cloud, and land Elevation Satellite) (Simard et al., 2011; Tang et al., 2014). Three widely used Leaf Area Index (LAI) products are compared as input to the GVSD and ACTS forcing in terms of vegetation albedo: Global Data Sets of Vegetation (LAI)3g (Zhu et al. 2013), Beijing Normal University LAI (Yuan et al., 2011), and MODIS MOD15A2H product (Yang et al., 2006). Further PFT partitioning is performed according to a climate classification utilizing the Climate Research Unit (CRU; Harris et al., 2013) and the NOAA Global Precipitation Climatology Centre (GPCC; Scheider et al., 2014) data. Final products are a GVSD consisting of mixed plant communities (e.g. mixed forests, savannas, mixed PFTs) following the Ecosystem Demography model (Moorcroft et al., 2001) approach represented by multi-cohort community patches at the sub-grid level of the GCM, which are ensembles of identical individuals whose differences are represented by PFTs, canopy height, density and vegetation structure sensitivity to allometric parameters. The performance of the Ent TBM in estimating VIS-NIR vegetation albedo by the new GVSD and ACTS is assessed first by comparison against the previous GISS GCM vegetation classification and prescribed Lambertian albedoes of Matthews (1984), and secondly, against MODIS global estimations and FLUXNET site-scale observations. Ultimately, this GVSD will serve as a template for community data sets, and be used as boundary conditions to the Ent TBM for prediction of biomass, carbon balances and GISS GCM climate.

Effectiveness of Different Urban Heat Island Mitigation Methods and Their Regional Impacts

NASA Astrophysics Data System (ADS)

Zhang, N.

2017-12-01

Cool roofs and green roofs are two popular methods to mitigate urban heat island and improve urban climate. The effectiveness of different urban heat island mitigation strategies in the summer of 2013 in the Yangtze River Delta, China is investigated using the WRF (Weather Research and Forecasting) model coupled with a physically based urban canopy model. The modifications to the roof surface changed the urban surface radiation balance and then modified the local surface energy budget. Both cool roofs and green roofs led to lower surface skin temperature and near-surface air temperature. Increasing the roof albedo to 0.5 caused a similar effectiveness as covering 25% of urban roofs with vegetation; increasing roof albedo to 0.7 caused a similar near-surface air temperature decrease as 75% green roof coverage. The near-surface relative humidity increased in both cool roof and green roof experiments because of the combination of the impacts of increases in specific humidity and decreases in air temperature. The regional impacts of cool roofs and green roofs were evaluated using the regional effect index. The regional effect could be found in both near-surface air temperature and surface specific/relative humidity when the percentage of roofs covered with high albedo materials or green roofs reached a higher fraction (greater than 50%). The changes in the vertical profiles of temperature cause a more stable atmospheric boundary layer over the urban area; at the same time, the crossover phenomena occurred above the boundary layer due to the decrease in vertical wind speed.

Quantifying avian nest survival along an urbanization gradient using citizen- and scientist-generated data.

PubMed

Ryder, Thomas B; Reitsma, Robert; Evans, Brian; Marra, Peter P

2010-03-01

Despite the increasing pace of urbanization little is known about the factors that limit bird populations (i.e., population-level processes) within the urban/suburban land-use matrix. Here, we report rates of nest survival within the matrix of an urban land-use gradient in the greater Washington, D.C., USA, area for five common songbirds using data collected by scientists and citizens as part of a project called Neighborhood Nestwatch. Using program MARK, we modeled the effects of species, urbanization at multiple spatial scales (canopy cover and impervious surface), and observer (citizen vs. scientist) on nest survival of four open-cup and one cavity-nesting species. In addition, artificial nests were used to determine the relative impacts of specific predators along the land-use gradient. Our results suggest that predation on nests within the land-use matrix declines with urbanization but that there are species-specific differences. Moreover, variation in nest survival among species was best explained by urbanization metrics measured at larger "neighborhood" spatial scales (e.g., 1000 m). Trends were supported by data from artificial nests and suggest that variable predator communities (avian vs. mammalian) are one possible mechanism to explain differential nest survival. In addition, we assessed the quality of citizen science data and show that citizens had no negative effect on nest survival and provided estimates of nest survival comparable to Smithsonian biologists. Although birds nesting within the urban matrix experienced higher nest survival, individuals also faced a multitude of other challenges such as contaminants and invasive species, all of which could reduce adult survival.

Housing Shortages in Urban Regions: Aggressive Interactions at Tree Hollows in Forest Remnants

PubMed Central

Davis, Adrian; Major, Richard E.; Taylor, Charlotte E.

2013-01-01

Urbanisation typically results in a reduction of hollow-bearing trees and an increase in the density of particularly species, potentially resulting in an increased level of competition as cavity-nesting species compete for a limited resource. To improve understanding of hollow usage between urban cavity-nesting species in Australia, particularly parrots, we investigated how the hollow-using assemblage, visitation rate, diversity and number of interactions varied between hollows within urban remnant forest and continuous forest. Motion-activated video cameras were installed, via roped access to the canopy, and hollow usage was monitored at 61 hollows over a two-year period. Tree hollows within urban remnants had a significantly different assemblage of visitors to those in continuous forest as well as a higher rate of visitation than hollows within continuous forest, with the rainbow lorikeet making significantly more visitations than any other taxa. Hollows within urban remnants were characterised by significantly higher usage rates and significantly more aggressive interactions than hollows within continuous forest, with parrots responsible for almost all interactions. Within urban remnants, high rates of hollow visitation and both interspecific and intraspecific interactions observed at tree hollows suggest the number of available optimal hollows may be limiting. Understanding the usage of urban remnant hollows by wildlife, as well as the role of parrots as a potential flagship for the conservation of tree-hollows, is vital to prevent a decrease in the diversity of urban fauna, particularly as other less competitive species risk being outcompeted by abundant native species. PMID:23555657

The ecological services of plant communities in parks for climate control and recreation-A case study in Shanghai, China.

PubMed

Li, Zhigang; Chen, Dan; Cai, Shize; Che, Shengquan

2018-01-01

Mitigating extreme heat in urban areas is beneficial and sometimes critical to human health. Thriving plant communities in community parks play an important role in mitigating extreme heat through providing cooling effect, while inevitably affecting how people perceive the benefits of using community parks for recreation. Thus, the impacts of plant communities on the thermal environment should be quantified to determine the optimal structure of the plant community. The goal would be to harmonize the functions of improving the thermal environment with the preferences people have related to the recreational benefits of plant communities with various levels of vegetation density. In this paper, the correlations between the structural characteristics of plant communities and their function in mitigating the thermal environment were investigated on calm summer days in Xincheng Central Park, Minhang District, Shanghai, China. In addition to analyzing the plant communities present and their effects on the park microclimate, a questionnaire was employed to determine the plant community preferences of recreational park users. The results showed that plant communities could reduce the air temperature by 1.23-2.42 °C and increase the relative humidity by 2.4-4.2% during the daytime. The microclimate conditions in plant communities with varying vegetation densities were significantly different. The canopy density and leaf area index primarily controlled the temperature reduction, while the canopy density and total canopy cover ratio primarily controlled the increase in humidity; meanwhile, these correlations varied at different times of the day. Moreover, most of the park users preferred a moderately dense plant community which met their environmental perceptions for recreation in parks. Age or education level variables of park users would also predict preferences for different plant community densities. Ultimately, one plant community pattern with appropriate canopy density (60%), leaf area index (≥3) and canopy cover ratio (total 0.80-1.20, with 0.6-0.75 for trees and 0.20-0.45 for shrubs/woodland area) was recommended, which would harmonize the functions of the mitigation of the thermal environment with most people's perception of a desirable vegetation density.

The ecological services of plant communities in parks for climate control and recreation—A case study in Shanghai, China

PubMed Central

Li, Zhigang; Chen, Dan; Cai, Shize; Che, Shengquan

2018-01-01

Mitigating extreme heat in urban areas is beneficial and sometimes critical to human health. Thriving plant communities in community parks play an important role in mitigating extreme heat through providing cooling effect, while inevitably affecting how people perceive the benefits of using community parks for recreation. Thus, the impacts of plant communities on the thermal environment should be quantified to determine the optimal structure of the plant community. The goal would be to harmonize the functions of improving the thermal environment with the preferences people have related to the recreational benefits of plant communities with various levels of vegetation density. In this paper, the correlations between the structural characteristics of plant communities and their function in mitigating the thermal environment were investigated on calm summer days in Xincheng Central Park, Minhang District, Shanghai, China. In addition to analyzing the plant communities present and their effects on the park microclimate, a questionnaire was employed to determine the plant community preferences of recreational park users. The results showed that plant communities could reduce the air temperature by 1.23–2.42 °C and increase the relative humidity by 2.4–4.2% during the daytime. The microclimate conditions in plant communities with varying vegetation densities were significantly different. The canopy density and leaf area index primarily controlled the temperature reduction, while the canopy density and total canopy cover ratio primarily controlled the increase in humidity; meanwhile, these correlations varied at different times of the day. Moreover, most of the park users preferred a moderately dense plant community which met their environmental perceptions for recreation in parks. Age or education level variables of park users would also predict preferences for different plant community densities. Ultimately, one plant community pattern with appropriate canopy density (60%), leaf area index (≥3) and canopy cover ratio (total 0.80–1.20, with 0.6–0.75 for trees and 0.20–0.45 for shrubs/woodland area) was recommended, which would harmonize the functions of the mitigation of the thermal environment with most people’s perception of a desirable vegetation density. PMID:29694401

Beneficiary level factors influencing Janani Suraksha Yojana utilization in urban slum population of trans-Yamuna area of Delhi.

PubMed

Vikram, K; Sharma, A K; Kannan, A T

2013-09-01

Janani Suraksha Yojana (JSY), a conditional cash transfer scheme introduced to improve the institutional delivery rates and thereby reduce the maternal and infant mortality was implemented in all States and Union Territories of India from 2007. The present study was carried out to identify the beneficiary level factors of utilization of JSY scheme in urban slums and resettlement colonies of trans-Yamuna area of Delhi. A cross-sectional community based survey was done of mothers of infants in the selected areas of the two districts by stratified random sampling on a population proportionate basis. Socio-demographic factors, antenatal services availed and distance of nearest health facility were studied. Outcome variable, a beneficiary, was a woman who had ever interacted with the ASHA of her area during the antenatal period of previous pregnancy and had child birth in an institution. Descriptive tables were drawn; univariate analysis followed by multiple logistic regression was applied for identifying the predictors for availing the benefits. Of the 469 mothers interviewed, 333 (71%) had institutional delivery, 128 (27.3%) had benefited from JSY scheme and 68 (14.5%) had received cash benefits of JSY. Belonging to Hindu religion and having had more than 6 antenatal check ups were the significant predictors of availing the benefits of JSY. There is a need to improve the awareness among urban slum population about the utilization of JSY scheme. Targeting difficult to access areas with special measures and encouraging more antenatal visits were essential, prerequisites to improve the impact of JSY.

The Borden Micrometeorological Experiment 2009 (BMW09): Micrometeorology and Stable Isotopes for Carbon Cycle Studies

NASA Astrophysics Data System (ADS)

Warland, J. S.; Wagner-Riddle, C.; Staebler, R. M.; Lee, X.; Bartlett, P. A.; Brown, S. E.; Kim, K.; Santos, E. A.; Chang, K.

2009-12-01

A large collaborative experiment took place during summer 2009 at the Environment Canada tower site on CFB Borden in southern Ontario. The site is a long-term flux monitoring station, instrumented for eddy covariance measurements of CO2 and H2O, soil respiration, canopy profiles of CO2, H2O and temperature, net radiation, and standard meteorological variables. During BMW09, we brought to the site additional instrumentation to monitor gradients of stable isotopes of CO2 and H2O, turbulence profiles in the canopy and additional soil respiration data. Tunable diode laser trace gas analyzers were used to make continuous, high-frequency measurements of 12CO2, 13CO2 and C16O18O and H216O, HDO and H218O. Measurements were made of gradients of these isotopes above the canopy and in the understory. Profiles of CO2, H2O, temperature and turbulence statistics were measured for inverse Lagrangian analysis, where concentration profiles are used to determine source strength profiles through the canopy, thus separating soil, understory and overstory components of the net exchange made by eddy covariance. The project combines stable isotope measurements with novel micrometeorological techniques with the goal of developing improved operational measurements and gaining new insight into carbon and water cycles through this two-pronged approach. The overall goal of this intensive measurement campaign was to provide detailed data on the carbon and water cycles within this natural ecosystem for use in model testing and improvement. Specifically, the project will use this data with the C&N-CLASS model (the Canadian Land Surface Scheme with additional carbon and nitrogen routines) to improve its ability to predict changes to natural ecosystems under a changing climate when used within GCM simulations. This poster will present an overview of the project, highlight preliminary results, and illustrate how these disparate datasets will be tied together to provide new insight into carbon cycling.

A conjunct near-surface spectroscopy system for fix-angle and multi-angle continuous measurements of canopy reflectance and sun-induced chlorophyll fluorescence

NASA Astrophysics Data System (ADS)

Zhang, Qian; Fan, Yifeng; Zhang, Yongguang; Chou, Shuren; Ju, Weimin; Chen, Jing M.

2016-09-01

An automated spectroscopy system, which is divided into fix-angle and multi-angle subsystems, for collecting simultaneous, continuous and long-term measurements of canopy hyper-spectra in a crop ecosystem is developed. The fix-angle subsystem equips two spectrometers: one is HR2000+ (OceanOptics) covering the spectral range 200-1100 nm with 1.0 nm spectral resolution, and another one is QE65PRO (OceanOptics) providing 0.1 nm spectral resolution within the 730-780 nm spectral range. Both spectrometers connect a cosine-corrected fiber-optic fixed up-looking to collect the down-welling irradiance and a bare fiber-optic to measure the up-welling radiance from the vegetation. An inline fiber-optic shutter FOS-2x2-TTL (OceanOptics) is used to switch between input fibers to collect the signal from either the canopy or sky at one time. QE65PRO is used to permit estimation of vegetation Sun-Induced Fluorescence (SIF) in the O2-A band. The data collection scheme includes optimization of spectrometer integration time to maximize the signal to noise ratio and measurement of instrument dark currency. The multi-angle subsystem, which can help understanding bidirectional reflectance effects, alternatively use HR4000 (OceanOptics) providing 0.1 nm spectral resolution within the 680-800 nm spectral range to measure multi-angle SIF. This subsystem additionally includes a spectrometer Unispec-DC (PPSystems) featuring both up-welling and down-welling channels with 3 nm spectral resolution covering the 300-1100 nm spectral range. Two down-looking fiber-optics are mounted on a rotating device PTU-D46 (FLIR Systems), which can rotate horizontally and vertically at 10° angular step widths. Observations can be used to calculate canopy reflectance, vegetation indices and SIF for monitoring plant physiological processes.

Advanced NASA Earth Science Mission Concept for Vegetation 3D Structure, Biomass and Disturbance

NASA Technical Reports Server (NTRS)

Ranson, K. Jon

2007-01-01

Carbon in forest canopies represents about 85% of the total carbon in the Earth's aboveground biomass (Olson et al., 1983). A major source of uncertainty in global carbon budgets derives from large errors in the current estimates of these carbon stocks (IPCC, 2001). The magnitudes and distributions of terrestrial carbon storage along with changes in sources and sinks for atmospheric C02 due to land use change remain the most significant uncertainties in Earth's carbon budget. These uncertainties severely limit accurate terrestrial carbon accounting; our ability to evaluate terrestrial carbon management schemes; and the veracity of atmospheric C02 projections in response to further fossil fuel combustion and other human activities. Measurements of vegetation three-dimensional (3D) structural characteristics over the Earth's land surface are needed to estimate biomass and carbon stocks and to quantify biomass recovery following disturbance. These measurements include vegetation height, the vertical profile of canopy elements (i.e., leaves, stems, branches), andlor the volume scattering of canopy elements. They are critical for reducing uncertainties in the global carbon budget. Disturbance by natural phenomena, such as fire or wind, as well as by human activities, such as forest harvest, and subsequent recovery, complicate the quantification of carbon storage and release. The resulting spatial and temporal heterogeneity of terrestrial biomass and carbon in vegetation make it very difficult to estimate terrestrial carbon stocks and quantify their dynamics. Vegetation height profiles and disturbance recovery patterns are also required to assess ecosystem health and characterize habitat. The three-dimensional structure of vegetation provides habitats for many species and is a control on biodiversity. Canopy height and structure influence habitat use and specialization, two fundamental processes that modify species richness and abundance across ecosystems. Accurate and consistent 3D measurements of forest structure at the landscape scale are needed for assessing impacts to animal habitats and biodiversity following disturbance.

Hybrid fiber links for accurate optical frequency comparison

NASA Astrophysics Data System (ADS)

Lee, Won-Kyu; Stefani, Fabio; Bercy, Anthony; Lopez, Olivier; Amy-Klein, Anne; Pottie, Paul-Eric

2017-05-01

We present the experimental demonstration of a local two-way optical frequency comparison over a 43-km-long urban fiber network without any requirement for measurement synchronization. We combined the local two-way scheme with a regular active noise compensation scheme that was implemented on another parallel fiber leading to a highly reliable and robust frequency transfer. This hybrid scheme allowed us to investigate the major limiting factors of the local two-way comparison. We analyzed the contributions of the interferometers at both local and remote locations to the phase noise of the local two-way signal. Using the ability of this setup to be injected by either a single laser or two independent lasers, we measured the contributions of the demodulated laser instabilities to the long-term instability. We show that a fractional frequency instability level of 10-20 at 10,000 s can be obtained using this simple setup after propagation over a distance of 43 km in an urban area.

Energy flux parametrization as an opportunity to get Urban Heat Island insights: The case of Athens, Greece (Thermopolis 2009 Campaign).

PubMed

Loupa, G; Rapsomanikis, S; Trepekli, A; Kourtidis, K

2016-01-15

Energy flux parameterization was effected for the city of Athens, Greece, by utilizing two approaches, the Local-Scale Urban Meteorological Parameterization Scheme (LUMPS) and the Bulk Approach (BA). In situ acquired data are used to validate the algorithms of these schemes and derive coefficients applicable to the study area. Model results from these corrected algorithms are compared with literature results for coefficients applicable to other cities and their varying construction materials. Asphalt and concrete surfaces, canyons and anthropogenic heat releases were found to be the key characteristics of the city center that sustain the elevated surface and air temperatures, under hot, sunny and dry weather, during the Mediterranean summer. A relationship between storage heat flux plus anthropogenic energy flux and temperatures (surface and lower atmosphere) is presented, that results in understanding of the interplay between temperatures, anthropogenic energy releases and the city characteristics under the Urban Heat Island conditions.

A Modulated-Gradient Parametrization for the Large-Eddy Simulation of the Atmospheric Boundary Layer Using the Weather Research and Forecasting Model

NASA Astrophysics Data System (ADS)

Khani, Sina; Porté-Agel, Fernando

2017-12-01

The performance of the modulated-gradient subgrid-scale (SGS) model is investigated using large-eddy simulation (LES) of the neutral atmospheric boundary layer within the weather research and forecasting model. Since the model includes a finite-difference scheme for spatial derivatives, the discretization errors may affect the simulation results. We focus here on understanding the effects of finite-difference schemes on the momentum balance and the mean velocity distribution, and the requirement (or not) of the ad hoc canopy model. We find that, unlike the Smagorinsky and turbulent kinetic energy (TKE) models, the calculated mean velocity and vertical shear using the modulated-gradient model, are in good agreement with Monin-Obukhov similarity theory, without the need for an extra near-wall canopy model. The structure of the near-wall turbulent eddies is better resolved using the modulated-gradient model in comparison with the classical Smagorinsky and TKE models, which are too dissipative and yield unrealistic smoothing of the smallest resolved scales. Moreover, the SGS fluxes obtained from the modulated-gradient model are much smaller near the wall in comparison with those obtained from the regular Smagorinsky and TKE models. The apparent inability of the LES model in reproducing the mean streamwise component of the momentum balance using the total (resolved plus SGS) stress near the surface is probably due to the effect of the discretization errors, which can be calculated a posteriori using the Taylor-series expansion of the resolved velocity field. Overall, we demonstrate that the modulated-gradient model is less dissipative and yields more accurate results in comparison with the classical Smagorinsky model, with similar computational costs.

Angular Normalization of Ground and Satellite Observations of Sun-induced Chlorophyll Fluorescence for Assessing Vegetation Productivity

NASA Astrophysics Data System (ADS)

Chen, J. M.; He, L.; Chou, S.; Ju, W.; Zhang, Y.; Joiner, J.; Liu, J.; Mo, G.

2017-12-01

Sun-induced chlorophyll fluorescence (SIF) measured from plant canopies originates mostly from sunlit leaves. Observations of SIF by satellite sensors, such as GOME-2 and GOSAT, are often made over large view zenith angle ranges, causing large changes in the viewed sunlit leaf fraction across the scanning swath. Although observations made by OCO-2 are near nadir, the observed sunlit leaf fraction could still vary greatly due to changes in the solar zenith angle with latitude and time of overpass. To demonstrate the importance of considering the satellite-target-view geometry in using SIF for assessing vegetation productivity, we conducted multi-angle measurements of SIF using a hyperspectral sensor mounted on an automated rotating system over a rice field near Nanjing, China. A method is developed to separate SIF measurements at each angle into sunlit and shaded leaf components, and an angularly normalized canopy-level SIF is obtained as the weighted sum of sunlit and shaded SIF. This normalized SIF is shown to be a much better proxy of GPP of the rice field measured by an eddy covariance system than the unnormalized SIF observations. The same normalization scheme is also applied to the far-red GOME-2 SIF observations on sunny days, and we found that the normalized SIF is better correlated with model-simulated GPP than the original SIF observations. The coefficient of determination (R2) is improved by 0.07±0.04 on global average using the normalization scheme. The most significant improvement in R2 by 0.09±0.04 is found in deciduous broadleaf forests, where the observed sunlit leaf fraction is highly sensitive to solar zenith angle.

Preferences for benefit packages for community-based health insurance: an exploratory study in Nigeria

PubMed Central

2010-01-01

Background It is important that community-based health insurance (CBHI) schemes are designed in such a way as to ensure the relevance of the benefit packages to potential clients. Hence, this paper provides an understanding of the preferred benefit packages by different economic status groups as well as urban and rural dwellers for CBHI in Southeast Nigeria. Methods The study took place in rural, urban and semi-urban communities of south-east Nigeria. A questionnaire was used to collect information from 3070 randomly picked household heads. Focus group discussions were used to collect qualitative data. Data was examined for links between preferences for benefit packages with SES and geographic residence of the respondents. Results Respondents in the rural areas and in the lower SES preferred a comprehensive benefit package which includes all inpatient, outpatient and emergencies services, while those in urban areas as well as those in the higher SES group showed a preference for benefit packages which will cover only basic disease control interventions. Conclusion Equity concerns in preferences for services to be offered by the CBHI scheme should be addressed for CBHI to succeed in different contexts. PMID:20540787

Towards Better Simulation of US Maize Yield Responses to Climate in the Community Earth System Model

NASA Astrophysics Data System (ADS)

Peng, B.; Guan, K.; Chen, M.; Lawrence, D. M.; Jin, Z.; Bernacchi, C.; Ainsworth, E. A.; DeLucia, E. H.; Lombardozzi, D. L.; Lu, Y.

2017-12-01

Global food security is undergoing continuing pressure from increased population and climate change despites the potential advancement in breeding and management technologies. Earth system models (ESMs) are essential tools to study the impacts of historical and future climate on regional and global food production, as well as to assess the effectiveness of possible adaptations and their potential feedback to climate. Here we developed an improved maize representation within the Community Earth System Model (CESM) by combining the strengths of both the Community Land Model version 4.5 (CLM4.5) and the Agricultural Production Systems sIMulator (APSIM) models. Specifically, we modified the maize planting scheme, incorporated the phenology scheme adopted from the APSIM model, added a new carbon allocation scheme into CLM4.5, and improved the estimation of canopy structure parameters including leaf area index (LAI) and canopy height. Unique features of the new model (CLM-APSIM) include more detailed phenology stages, an explicit implementation of the impacts of various abiotic environmental stresses (including nitrogen, water, temperature and heat stresses) on maize phenology and carbon allocation, as well as an explicit simulation of grain number and grain size. We conducted a regional simulation of this new model over the US Corn Belt during 1990 to 2010. The simulated maize yield as well as its responses to climate (growing season mean temperature and precipitation) are benchmarked with data from UADA NASS statistics. Our results show that the CLM-APSIM model outperforms the CLM4.5 in simulating county-level maize yield production and reproduces more realistic yield responses to climate variations than CLM4.5. However, some critical processes (such as crop failure due to frost and inundation and suboptimal growth condition due to biotic stresses) are still missing in both CLM-APSIM and CLM4.5, making the simulated yield responses to climate slightly deviate from the reality. Our results demonstrate that with improved paramterization of crop growth, the ESMs can be powerful tools for realistically simulating agricultural production, which is gaining increasing interests and critical to study of global food security and food-energy-water nexus.

Implementation of an urban irrigation and a biofiltration system in the urban canopy model CLM-U

NASA Astrophysics Data System (ADS)

Demuzere, Matthias; Coutts, Andrew; Göhler, Maren; Diels, Jan; Gebert, Luke; Wouters, Hendrik; Van Lipzig, Nicole

2013-04-01

A recent review by Coutts et al. (2012) points out that to date the role of water in influencing urban climates through both irrigation and the support of urban vegetation receives less attention. Impervious urban surfaces prevent infiltration, and runoff is rapidly exported away from urban environments via the stormwater network. This produces a deficit of water in urban areas, and reduces soil moisture levels - a deficit that is often balanced by imported potable water to maintain a healthy vegetation via irrigation. Because of long-term dry spells over large areas of Australia in the last decades, State Governments introduced compulsory and voluntary strategies to encourage water saving across the community - including outdoor water restrictions. In this respect, residents have adapted gardening approaches by planting more drought-tolerant species. Each of these factors of drought, water restrictions and xeric gardens, along with the reduced health of urban vegetation, may further exacerbate urban warming and energy demands. In this respect, this study explores possible pathways towards a more Water Sensitive Urban Design (WSUD), implementing a decentralisation of water supply via residential rainwater tanks that collect run-off water from the roofs, an urban irrigation system connected to these rainwater tanks and bio-infiltration systems in which the impervious road fraction drains. All changes are implemented in the Community Land Model - Urban (CLM-U) and several sensitivity tests are performed for the residential area of Preston (Melbourne, Australia) in order to answer the question on how much water is actually needed to maintain healthy vegetation and where this water should come from. Can rainwater tanks provide a sufficient capacity to irrigate bio-infiltration systems or will it be necessary to apply high-quality potable water? In addition, this research can also be used to quantify the role of WSUD with respect to thermal comfort.

Evaluation of urban surface parameterizations in the WRF model using measurements during the Texas Air Quality Study 2006 field campaign

NASA Astrophysics Data System (ADS)

Lee, S.-H.; Kim, S.-W.; Angevine, W. M.; Bianco, L.; McKeen, S. A.; Senff, C. J.; Trainer, M.; Tucker, S. C.; Zamora, R. J.

2010-10-01

The impact of urban surface parameterizations in the WRF (Weather Research and Forecasting) model on the simulation of local meteorological fields is investigated. The Noah land surface model (LSM), a modified LSM, and a single-layer urban canopy model (UCM) have been compared, focusing on urban patches. The model simulations were performed for 6 days from 12 August to 17 August during the Texas Air Quality Study 2006 field campaign. Analysis was focused on the Houston-Galveston metropolitan area. The model simulated temperature, wind, and atmospheric boundary layer (ABL) height were compared with observations from surface meteorological stations (Continuous Ambient Monitoring Stations, CAMS), wind profilers, the NOAA Twin Otter aircraft, and the NOAA Research Vessel Ronald H. Brown. The UCM simulation showed better results in the comparison of ABL height and surface temperature than the LSM simulations, whereas the original LSM overestimated both the surface temperature and ABL height significantly in urban areas. The modified LSM, which activates hydrological processes associated with urban vegetation mainly through transpiration, slightly reduced warm and high biases in surface temperature and ABL height. A comparison of surface energy balance fluxes in an urban area indicated the UCM reproduces a realistic partitioning of sensible heat and latent heat fluxes, consequently improving the simulation of urban boundary layer. However, the LSMs have a higher Bowen ratio than the observation due to significant suppression of latent heat flux. The comparison results suggest that the subgrid heterogeneity by urban vegetation and urban morphological characteristics should be taken into account along with the associated physical parameterizations for accurate simulation of urban boundary layer if the region of interest has a large fraction of vegetation within the urban patch. Model showed significant discrepancies in the specific meteorological conditions when nocturnal low-level jets exist and a thermal internal boundary layer over water forms.

A Case Study of Urbanization Impact on Summer Precipitation in the Greater Beijing Metropolitan Area. Urban Heat Island Versus Aerosol Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong, Shi; Qian, Yun; Zhao, Chun

Convection-resolving ensemble simulations using the WRF-Chem model coupled with a single-layer Urban Canopy Model (UCM) are conducted to investigate the individual and combined impacts of land use and anthropogenic pollutant emissions from urbanization on a heavy rainfall event in the Greater Beijing Metropolitan Area (GBMA) in China. The simulation with the urbanization effect included generally captures the spatial pattern and temporal variation of the rainfall event. An improvement of precipitation is found in the experiment including aerosol effect on both clouds and radiation. The expanded urban land cover and increased aerosols have an opposite effect on precipitation processes, with themore » latter playing a more dominant role, leading to suppressed convection and rainfall over the upstream (northwest) area, and enhanced convection and more precipitation in the downstream (southeast) region of the GBMA. In addition, the influence of aerosol indirect effect is found to overwhelm that of direct effect on precipitation in this rainfall event. Increased aerosols induce more cloud droplets with smaller size, which favors evaporative cooling and reduce updrafts and suppress convection over the upstream (northwest) region in the early stage of the rainfall event. As the rainfall system propagates southeastward, more latent heat is released due to the freezing of larger number of smaller cloud drops that are lofted above the freezing level, which is responsible for the increased updraft strength and convective invigoration over the downstream (southeast) area.« less

3D modeling of satellite spectral images, radiation budget and energy budget of urban landscapes

NASA Astrophysics Data System (ADS)

Gastellu-Etchegorry, J. P.

2008-12-01

DART EB is a model that is being developed for simulating the 3D (3 dimensional) energy budget of urban and natural scenes, possibly with topography and atmosphere. It simulates all non radiative energy mechanisms (heat conduction, turbulent momentum and heat fluxes, water reservoir evolution, etc.). It uses DART model (Discrete Anisotropic Radiative Transfer) for simulating radiative mechanisms: 3D radiative budget of 3D scenes and their remote sensing images expressed in terms of reflectance or brightness temperature values, for any atmosphere, wavelength, sun/view direction, altitude and spatial resolution. It uses an innovative multispectral approach (ray tracing, exact kernel, discrete ordinate techniques) over the whole optical domain. This paper presents two major and recent improvements of DART for adapting it to urban canopies. (1) Simulation of the geometry and optical characteristics of urban elements (houses, etc.). (2) Modeling of thermal infrared emission by vegetation and urban elements. The new DART version was used in the context of the CAPITOUL project. For that, districts of the Toulouse urban data base (Autocad format) were translated into DART scenes. This allowed us to simulate visible, near infrared and thermal infrared satellite images of Toulouse districts. Moreover, the 3D radiation budget was used by DARTEB for simulating the time evolution of a number of geophysical quantities of various surface elements (roads, walls, roofs). Results were successfully compared with ground measurements of the CAPITOUL project.

Juvenile coho salmon growth and health in streams across an urbanization gradient

USGS Publications Warehouse

Spanjer, Andrew R.; Moran, Patrick W.; Larsen, Kimberly; Wetzel, Lisa; Hansen, Adam G.; Beauchamp, David A.

2018-01-01

Expanding human population and urbanization alters freshwater systems through structural changes to habitat, temperature effects from increased runoff and reduced canopy cover, altered flows, and increased toxicants. Current stream assessments stop short of measuring health or condition of species utilizing these freshwater habitats and fail to link specific stressors mechanistically to the health of organisms in the stream. Juvenile fish growth integrates both external and internal conditions providing a useful indicator of habitat quality and ecosystem health. Thus, there is a need to account for ecological and environmental influences on fish growth accurately. Bioenergetics models can simulate changes in growth and consumption in response to environmental conditions and food availability to account for interactions between an organism's environmental experience and utilization of available resources. The bioenergetics approach accounts for how thermal regime, food supply, and food quality affect fish growth. This study used a bioenergetics modeling approach to evaluate the environmental factors influencing juvenile coho salmon growth among ten Pacific Northwest streams spanning an urban gradient. Urban streams tended to be warmer, have earlier emergence dates and stronger early season growth. However, fish in urban streams experienced increased stress through lower growth efficiencies, especially later in the summer as temperatures warmed, with as much as a 16.6% reduction when compared to fish from other streams. Bioenergetics modeling successfully characterized salmonid growth in small perennial streams as part of a more extensive monitoring program and provides a powerful assessment tool for characterizing mixed life-stage specific responses in urban streams.

Sensitivity of snow process simulations to precipitation-phase transition method in forested and open areas

NASA Astrophysics Data System (ADS)

Lundberg, A.; Gustafsson, D.

2009-04-01

Modeling of forest snow processes is complicated and especially problematic seems to be the separation of precipitation phase in climates where a large part of the precipitation falls at temperatures near zero degrees Celsius. When the precipitation is classified as snow, the tree crowns can carry an order of magnitude more canopy storage as compared to when the precipitation is classified as rain, and snow in the trees also alters the albedo of the forest while rain does not. Many different schemes for the precipitation phase separation are used by various snow models. Some models use just one air temperature threshold (TR/S) below which all precipitation is assumed to be snow and above which all precipitation is classified as rain. A more common approach for forest snow models is to use two temperature thresholds. The snow fraction (SF) is then set to one below the snow threshold (TS) and to zero above the rain threshold (TR) and SF is assumed to decrease linearly between these two thresholds. Also more sophisticated schemes exist, but three seems to be a lack of agreement on how the precipitation phase separations should be performed. The aim with this study is to use a hydrological model including canopy snow processes to illustrate the sensitivity for different formulations of the precipitation phase separation on a) the simulated maximum snow pack storage b) the interception evaporation loss and c) snow melt runoff. In other words, to investigate of the choice of precipitation phase separation has an impact on the simulated wintertime water balance. Simulations are made for sites in different climates and for both open fields and forest sites in different regions of Sweden from north to south. In general, precipitation phase separation methods that classified snowfall at higher temperatures resulted in a larger proportion of the precipitation lost by interception evaporation as a result of the increased interception capacity. However, the maximum snow accumulation was also increased in some cases due to the overall increased snowfall, depending on canopy density and precipitation and temperature regimes. Results show that the choice of precipitation phase separation method can have an significant impact on the simulated wintertime water balance, especially in forested regions.

Application of transilient turbulent theory to study interactions between the atmospheric boundary layer and forest canopies

NASA Astrophysics Data System (ADS)

Inclán, M. G.; Forkel, R.; Dlugi, R.; Stull, R. B.

1996-06-01

The new Forest-Land-Atmosphere ModEl called FLAME is presented. The first-order, nonlocal turbulence closure called transilient turbulence theory (Stull, 1993) is applied to study the interactions between a forested land-surface and the atmospheric boundary layer (ABL). The transilient scheme is used for unequal vertical grid spacing and includes the effects of drag, wake turbulence, and interference to vertical mixing by plant elements. Radiation transfer within the vegetation and the equations for the energy balance at the leaf surface have been taken from Norman (1979). Among others, the model predicts profiles of air temperature, humidity and wind velocity within the ABL, sensible and latent heat fluxes from the soil and the vegetation, the stomata and aerodynamic resistances, as well as profiles of temperature and water content in the soil. Preliminary studies carried out for a cloud free day and idealized initial conditions are presented. The canopy height is 30 m within a vertical domain of 3 km. The model is able to capture some of the effects usually observed within and above forested areas, including the relative wind speed maximum in the trunk space and the counter gradient-fluxes in the lower part of the plant stand. Of special interest is the determination of the location and magnitude of the turbulent mixing between model layers, which permits one to identify the effects of large eddies transporting momentum and scalar quantities into the canopy. A comparison between model simulations and field measurements will be presented in a future paper.

Actual and potential transpiration and carbon assimilation in an irrigated poplar plantation.

PubMed

Kim, Hyun-Seok; Oren, Ram; Hinckley, Thomas M

2008-04-01

We examined the tradeoffs between stand-level water use and carbon uptake that result when biomass production of trees in plantations is maximized by removing nutrient and water limitations. A Populus trichocarpa Torr. x P. deltoides Bartr. & Marsh. plantation was irrigated and received frequent additions of nutrients to optimize biomass production. Sap flux density was measured continuously over four of the six growing-season months, supplemented with periodic measurements of leaf gas exchange and water potential. Measurements of tree diameter and height were used to estimate leaf area and biomass production based on allometric relationships. Sap flux was converted to canopy conductance and analyzed with an empirical model to isolate the effects of water limitation. Actual and soil-water-unlimited potential CO(2) uptakes were estimated with a canopy conductance constrained carbon assimilation (4C-A) scheme, which couples actual or potential canopy conductance with vertical gradients of light distribution, leaf-level conductance, maximum Rubisco capacity and maximum electron transport. Net primary production (NPP) was about 43% of gross primary production (GPP); when estimated for individual trees, this ratio was independent of tree size. Based on the NPP/GPP ratio, we found that current irrigation reduced growth by about 18% compared with growth with no water limitation. To achieve maximum growth, however, would require 70% more water for transpiration, and would reduce water-use efficiency by 27%, from 1.57 to 1.15 g stem wood C kg(-1) water. Given the economic and social values of water, plantation managers appear to have optimized water use.

Numerical Simulation of Dispersion from Urban Greenhouse Gas Sources

NASA Astrophysics Data System (ADS)

Nottrott, Anders; Tan, Sze; He, Yonggang; Winkler, Renato

2017-04-01

Cities are characterized by complex topography, inhomogeneous turbulence, and variable pollutant source distributions. These features create a scale separation between local sources and urban scale emissions estimates known as the Grey-Zone. Modern computational fluid dynamics (CFD) techniques provide a quasi-deterministic, physically based toolset to bridge the scale separation gap between source level dynamics, local measurements, and urban scale emissions inventories. CFD has the capability to represent complex building topography and capture detailed 3D turbulence fields in the urban boundary layer. This presentation discusses the application of OpenFOAM to urban CFD simulations of natural gas leaks in cities. OpenFOAM is an open source software for advanced numerical simulation of engineering and environmental fluid flows. When combined with free or low cost computer aided drawing and GIS, OpenFOAM generates a detailed, 3D representation of urban wind fields. OpenFOAM was applied to model scalar emissions from various components of the natural gas distribution system, to study the impact of urban meteorology on mobile greenhouse gas measurements. The numerical experiments demonstrate that CH4 concentration profiles are highly sensitive to the relative location of emission sources and buildings. Sources separated by distances of 5-10 meters showed significant differences in vertical dispersion of plumes, due to building wake effects. The OpenFOAM flow fields were combined with an inverse, stochastic dispersion model to quantify and visualize the sensitivity of point sensors to upwind sources in various built environments. The Boussinesq approximation was applied to investigate the effects of canopy layer temperature gradients and convection on sensor footprints.

Could the employment-based targeting approach serve Egypt in moving towards a social health insurance model?

PubMed

Shawky, S

2010-06-01

The current health insurance system in Egypt targets the productive population through an employment-based scheme bounded by a cost ceiling and focusing on curative care. Egypt Social Contract Survey data from 2005 were used to evaluate the impact of the employment-based scheme on health system accessibility and financing. Only 22.8% of the population in the productive age range (19-59 years) benefited from any health insurance scheme. The employment-based scheme covered 39.3% of the working population and was skewed towards urban areas, older people, females and the wealthier. It did not increase service utilization, but reduced out-of-pocket expenditure. Egypt should blend all health insurance schemes and adopt an innovative approach to reach universal coverage.

An Ecological Analysis of Environmental Correlates of Active Commuting in Urban U.S.

PubMed Central

Fan, Jessie X.; Wen, Ming; Kowaleski-Jones, Lori

2014-01-01

We conduct a cross-sectional ecological analysis to examine environmental correlates of active commuting in 39,660 urban tracts using data from the 2010 Census, 2007-2011 American Community Survey, and other sources. The five-year average (2007-2011) prevalence is 3.05% for walking, 0.63% for biking, and 7.28% for public transportation to work, with higher prevalence for all modes in lower-income tracts. Environmental factors account for more variances in public transportation to work but economic and demographic factors account for more variances in walking and biking to work. Population density, median housing age, street connectivity, tree canopy, distance to parks, air quality, and county sprawl index are associated with active commuting, but the association can vary in size and direction for different transportation mode and for higher-income and lower-income tracts. PMID:25460907

An ecological analysis of environmental correlates of active commuting in urban U.S.

PubMed

Fan, Jessie X; Wen, Ming; Kowaleski-Jones, Lori

2014-11-01

We conduct a cross-sectional ecological analysis to examine environmental correlates of active commuting in 39,660 urban tracts using data from the 2010 Census, 2007-2011 American Community Survey, and other sources. The five-year average (2007-2011) prevalence is 3.05% for walking, 0.63% for biking, and 7.28% for public transportation to work, with higher prevalence for all modes in lower-income tracts. Environmental factors account for more variances in public transportation to work but economic and demographic factors account for more variances in walking and biking to work. Population density, median housing age, street connectivity, tree canopy, distance to parks, air quality, and county sprawl index are associated with active commuting, but the association can vary in size and direction for different transportation mode and for higher-income and lower-income tracts. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Survey on Urban Traffic Management System Using Wireless Sensor Networks.

PubMed

Nellore, Kapileswar; Hancke, Gerhard P

2016-01-27

Nowadays, the number of vehicles has increased exponentially, but the bedrock capacities of roads and transportation systems have not developed in an equivalent way to efficiently cope with the number of vehicles traveling on them. Due to this, road jamming and traffic correlated pollution have increased with the associated adverse societal and financial effect on different markets worldwide. A static control system may block emergency vehicles due to traffic jams. Wireless Sensor networks (WSNs) have gained increasing attention in traffic detection and avoiding road congestion. WSNs are very trendy due to their faster transfer of information, easy installation, less maintenance, compactness and for being less expensive compared to other network options. There has been significant research on Traffic Management Systems using WSNs to avoid congestion, ensure priority for emergency vehicles and cut the Average Waiting Time (AWT) of vehicles at intersections. In recent decades, researchers have started to monitor real-time traffic using WSNs, RFIDs, ZigBee, VANETs, Bluetooth devices, cameras and infrared signals. This paper presents a survey of current urban traffic management schemes for priority-based signalling, and reducing congestion and the AWT of vehicles. The main objective of this survey is to provide a taxonomy of different traffic management schemes used for avoiding congestion. Existing urban traffic management schemes for the avoidance of congestion and providing priority to emergency vehicles are considered and set the foundation for further research.

A Survey on Urban Traffic Management System Using Wireless Sensor Networks

PubMed Central

Nellore, Kapileswar; Hancke, Gerhard P.

2016-01-01

Nowadays, the number of vehicles has increased exponentially, but the bedrock capacities of roads and transportation systems have not developed in an equivalent way to efficiently cope with the number of vehicles traveling on them. Due to this, road jamming and traffic correlated pollution have increased with the associated adverse societal and financial effect on different markets worldwide. A static control system may block emergency vehicles due to traffic jams. Wireless Sensor networks (WSNs) have gained increasing attention in traffic detection and avoiding road congestion. WSNs are very trendy due to their faster transfer of information, easy installation, less maintenance, compactness and for being less expensive compared to other network options. There has been significant research on Traffic Management Systems using WSNs to avoid congestion, ensure priority for emergency vehicles and cut the Average Waiting Time (AWT) of vehicles at intersections. In recent decades, researchers have started to monitor real-time traffic using WSNs, RFIDs, ZigBee, VANETs, Bluetooth devices, cameras and infrared signals. This paper presents a survey of current urban traffic management schemes for priority-based signalling, and reducing congestion and the AWT of vehicles. The main objective of this survey is to provide a taxonomy of different traffic management schemes used for avoiding congestion. Existing urban traffic management schemes for the avoidance of congestion and providing priority to emergency vehicles are considered and set the foundation for further research. PMID:26828489

Associating Land Surface Temperature Retrieved From Satellite and Unmanned Aerial Vehicle Data With Urban Cover and Topography in Aburrá Valley

NASA Astrophysics Data System (ADS)

Guzmán, G.; Hoyos Ortiz, C. D.

2017-12-01

Urban heat island effect commonly refers to temperature differences between urban areas and their countrysides due to urbanization. These temperature differences are evident at surface, and within the canopy and the boundary layer. This effect is heterogeneous within the city, and responds to urban morphology, prevailing materials, amount of vegetation, among others, which are also important in the urban balance of energy. In order to study the relationship between land surface temperature (LST) and urban coverage over Aburrá Valley, which is a narrow valley locate at tropical Andes in northern South America, Landsat 8 mission products of LST, density of vegetation (normalized difference vegetation index, NDVI), and a proxy of soil humidity are derived and used. The results are analyzed from the point of view of dominant urban form and settlement density at scale of neighborhoods, and also from potential downward solar radiation received at the surface. Besides, specific sites were chosen to obtain LST from thermal imaging using an unmanned aerial vehicle to characterize micro-scale patterns and to validate Landast retrievals. Direct relationships between LST, NDVI, soil humidity, and duration of insolation are found, showing the impact of the current spatial distribution of land uses on surface temperature over Aburrá Valley. In general, the highest temperatures correspond to neighborhoods with large, flat-topped buildings in commercial and industrial areas, and low-rise building in residential areas with scarce vegetation, all on the valley bottom. Landsat images are in the morning for the Aburrá Valley, for that reason the coldest temperatures are prevalent at certain orientation of the hillslope, according with the amount of radiation received from sunrise to time of data.

Semi-Automated Approach for Mapping Urban Trees from Integrated Aerial LiDAR Point Cloud and Digital Imagery Datasets

NASA Astrophysics Data System (ADS)

Dogon-Yaro, M. A.; Kumar, P.; Rahman, A. Abdul; Buyuksalih, G.

2016-09-01

Mapping of trees plays an important role in modern urban spatial data management, as many benefits and applications inherit from this detailed up-to-date data sources. Timely and accurate acquisition of information on the condition of urban trees serves as a tool for decision makers to better appreciate urban ecosystems and their numerous values which are critical to building up strategies for sustainable development. The conventional techniques used for extracting trees include ground surveying and interpretation of the aerial photography. However, these techniques are associated with some constraints, such as labour intensive field work and a lot of financial requirement which can be overcome by means of integrated LiDAR and digital image datasets. Compared to predominant studies on trees extraction mainly in purely forested areas, this study concentrates on urban areas, which have a high structural complexity with a multitude of different objects. This paper presented a workflow about semi-automated approach for extracting urban trees from integrated processing of airborne based LiDAR point cloud and multispectral digital image datasets over Istanbul city of Turkey. The paper reveals that the integrated datasets is a suitable technology and viable source of information for urban trees management. As a conclusion, therefore, the extracted information provides a snapshot about location, composition and extent of trees in the study area useful to city planners and other decision makers in order to understand how much canopy cover exists, identify new planting, removal, or reforestation opportunities and what locations have the greatest need or potential to maximize benefits of return on investment. It can also help track trends or changes to the urban trees over time and inform future management decisions.

Biophysical control of whole tree transpiration under an urban environment in Northern China

NASA Astrophysics Data System (ADS)

Chen, Lixin; Zhang, Zhiqiang; Li, Zhandong; Tang, Jianwu; Caldwell, Peter; Zhang, Wenjuan

2011-05-01

SummaryUrban reforestation in China has led to increasing debate about the impact of urban trees and forests on water resources. Although transpiration is the largest water flux leaving terrestrial ecosystems, little is known regarding whole tree transpiration in urban environments. In this study, we quantified urban tree transpiration at various temporal scales and examined the biophysical control of the transpiration pattern under different water conditions to understand how trees survive in an urban environment. Concurrent with microclimate and soil moisture measurements, transpiration from C edrus deodara(Roxb)Loud ., Zelkova schneideriana Hend.-Mazz., Euonymus bungeanus Maxim., and Metasequoia glyptostroboides Hu et cheng was measured over a 2-year period using thermal dissipation probe (TDP) techniques. The average monthly transpiration rates reached 12.78 ± 0.73 (S.E.) mm, 1.79 ± 0.16 mm, 10.18 ± 0.55 mm and 19.28 ± 2.24 mm for C. deodara, Z.schneideriana, E. bungeanus and M. glyptostroboides, respectively. Transpiration rates from M. glyptostroboides reported here may need further study as this species showed much higher sap flows and greater transpiration fluctuation under different environmental conditions than other species. Because of deep soil moisture supply, summer dry spells did not reduce transpiration rates even when tree transpiration exceeded rainfall. While vapor pressure deficit ( VPD) was the dominant environmental factor on transpiration, trees controlled canopy conductance effectively to limit transpiration in times of water stress. Our results provide evidence that urban trees could adopt strong physiological control over transpiration under high evaporative demands to avoid dehydration and can make use of water in deeper soil layers to survive summer dry spells. Moreover, urban trees have the ability to make the best use of precipitation when it is limited, and are sensitive to soil and air dryness.

A new technique for fire risk estimation in the wildland urban interface

NASA Astrophysics Data System (ADS)

Dasgupta, S.; Qu, J. J.; Hao, X.

A novel technique based on the physical variable of pre-ignition energy is proposed for assessing fire risk in the Grassland-Urban-Interface The physical basis lends meaning a site and season independent applicability possibilities for computing spread rates and ignition probabilities features contemporary fire risk indices usually lack The method requires estimates of grass moisture content and temperature A constrained radiative-transfer inversion scheme on MODIS NIR-SWIR reflectances which reduces solution ambiguity is used for grass moisture retrieval while MODIS land surface temperature emissivity products are used for retrieving grass temperature Subpixel urban contamination of the MODIS reflective and thermal signals over a Grassland-Urban-Interface pixel is corrected using periodic estimates of urban influence from high spatial resolution ASTER

Vegetation coupling to global climate: Trajectories of vegetation change and phenology modeling from satellite observations

NASA Astrophysics Data System (ADS)

Fisher, Jeremy Isaac

Important systematic shifts in ecosystem function are often masked by natural variability. The rich legacy of over two decades of continuous satellite observations provides an important database for distinguishing climatological and anthropogenic ecosystem changes. Examples from semi-arid Sudanian West Africa and New England (USA) illustrate the response of vegetation to climate and land-use. In Burkina Faso, West Africa, pastoral and agricultural practices compete for land area, while degradation may follow intensification. The Nouhao Valley is a natural experiment in which pastoral and agricultural land uses were allocated separate, coherent reserves. Trajectories of annual net primary productivity were derived from 18 years of coarse-grain (AVHRR) satellite data. Trends suggested that pastoral lands had responded rigorously to increasing rainfall after the 1980's droughts. A detailed analysis at Landsat resolution (30m) indicated that the increased vegetative cover was concentrated in the river basins of the pastoral region, implying a riparian wood expansion. In comparison, riparian cover was reduced in agricultural regions. We suggest that broad-scale patterns of increasing semi-arid West African greenness may be indicative of climate variability, whereas local losses may be anthropogenic in nature. The contiguous deciduous forests, ocean proximity, topography, and dense urban developments of New England provide an ideal landscape to examine influences of climate variability and the impact of urban development vegetation response. Spatial and temporal patterns of interannual climate variability were examined via green leaf phenology. Phenology, or seasonal growth and senescence, is driven by deficits of light, temperature, and water. In temperate environments, phenology variability is driven by interannual temperature and precipitation shifts. Average and interannual phenology analyses across southern New England were conducted at resolutions of 30m (Landsat) and 500m Moderate Resolution Imaging Spectrometer (MODIS). A robust logistic-growth model of canopy cover was employed to determine phenological characteristics at each forest stand. The duel analyses revealed important findings: (a) local phenological gradients from microclimatic structures are highly influential in broad-scale phenological observations; (b) satellite observed phenology reflects observations of canopy growth from field studies; (c) phenological anomalies in urban areas which were previously attributed to urban heat may be a function of urban-specific land cover (i.e. green lawns); and (d) patterns of interannual variability in phenology at the regional scale have high spatial coherency and appear to be driven by broad-scale climatic change. Satellite-observed phenology may reflect temperatures during spring and provides a proxy of climate variability.

Extracting Tree Height from Repeat-Pass PolInSAR Data : Experiments with JPL and ESA Airborne Systems

NASA Technical Reports Server (NTRS)

Lavalle, Marco; Ahmed, Razi; Neumann, Maxim; Hensley, Scott

2013-01-01

In this paper we present our latest developments and experiments with the random-motion-over-ground (RMoG) model used to extract canopy height and other important forest parameters from repeat-pass polarimetricinterferometric SAR (Pol-InSAR) data. More specifically, we summarize the key features of the RMoG model in contrast with the random-volume-over-ground (RVoG) model, describe in detail a possible inversion scheme for the RMoG model and illustrate the results of the RMoG inversion using airborne data collected by the Jet Propulsion Laboratory (JPL) and the European Space Agency (ESA).

Evaluation of urban surface parameterizations in the WRF model using measurements during the Texas Air Quality Study 2006 field campaign

NASA Astrophysics Data System (ADS)

Lee, S.-H.; Kim, S.-W.; Angevine, W. M.; Bianco, L.; McKeen, S. A.; Senff, C. J.; Trainer, M.; Tucker, S. C.; Zamora, R. J.

2011-03-01

The performance of different urban surface parameterizations in the WRF (Weather Research and Forecasting) in simulating urban boundary layer (UBL) was investigated using extensive measurements during the Texas Air Quality Study 2006 field campaign. The extensive field measurements collected on surface (meteorological, wind profiler, energy balance flux) sites, a research aircraft, and a research vessel characterized 3-dimensional atmospheric boundary layer structures over the Houston-Galveston Bay area, providing a unique opportunity for the evaluation of the physical parameterizations. The model simulations were performed over the Houston metropolitan area for a summertime period (12-17 August) using a bulk urban parameterization in the Noah land surface model (original LSM), a modified LSM, and a single-layer urban canopy model (UCM). The UCM simulation compared quite well with the observations over the Houston urban areas, reducing the systematic model biases in the original LSM simulation by 1-2 °C in near-surface air temperature and by 200-400 m in UBL height, on average. A more realistic turbulent (sensible and latent heat) energy partitioning contributed to the improvements in the UCM simulation. The original LSM significantly overestimated the sensible heat flux (~200 W m-2) over the urban areas, resulting in warmer and higher UBL. The modified LSM slightly reduced warm and high biases in near-surface air temperature (0.5-1 °C) and UBL height (~100 m) as a result of the effects of urban vegetation. The relatively strong thermal contrast between the Houston area and the water bodies (Galveston Bay and the Gulf of Mexico) in the LSM simulations enhanced the sea/bay breezes, but the model performance in predicting local wind fields was similar among the simulations in terms of statistical evaluations. These results suggest that a proper surface representation (e.g. urban vegetation, surface morphology) and explicit parameterizations of urban physical processes are required for accurate urban atmospheric numerical modeling.

Comparing the urbanization and global warming impacts on extreme rainfall characteristics in Southern China Pearl River Delta megacity based on dynamical downscaling

NASA Astrophysics Data System (ADS)

Fung, K. Y.; Tam, C. Y.; Wang, Z.

2017-12-01

It is well known that urban land use can significantly influence the local temperature, precipitation and meteorology through altering land-atmosphere exchange of momentum, moisture and heat in urban areas. In recent decades, there has been a substantial increase ( 5-10%) on the intensity of extreme rainfall over Southeast China; it is projected to increase further according to the latest IPCC reports. In this study, we assess how urbanization and global warming together might impact on heavy precipitation characteristics over the highly urbanized Pearl River Delta (PRD) megacity, located in southern China. This is done by dynamically downscaling GFDL-ESM2M simulations for the present and future (RCP8.5) climate scenarios, using the Weather Research and Forecasting (WRF) model coupled with a single-layer urban canopy model (UCM). Over the PRD area, the WRF model is integrated at a resolution of 2km x 2km. To focus on extreme events, episodes covering daily rainfall intensity above the 99th percentile in Southeast China in the GFDL-ESM2M daily precipitation datasets were first identified. These extreme episodes were then dynamically downscaled in two parallel experiments with the following model designs: one with anthropogenic heat flux (AH) = 0 Wm-2 and the other with peak AH = 300 Wm-2 in the AH diurnal cycle over the urban domain. Results show that, with AH in urban area, the urban 2m-temperature can rise by about 2oC. This in turn leads to an increase of the mean as well as the extreme rain rates by 10-15% in urban domain. The latter is comparable to the impact of global warming alone, according to downscaling experiments for the RCP8.5 scenario. Implications of our results on urban effects on extreme rainfall under a warming background climate will be discussed.

K-12 Phenology Lessons for the Phenocam Project

NASA Astrophysics Data System (ADS)

Bennett, K. F.

2013-12-01

Phenology is defined as periodic [or annual] life cycles of plants and animals driven by seasonal environmental changes. Climate change impinges a strong effect on phenology, potentially altering the structure and functioning of ecosystems. In the fall of 2011, the Ashburnham-Westminster Regional School District became the first of five schools to join Harvard University's Phenocam Network with the installation of a webcam to monitor phenology (or 'phenocam') at Overlook Middle School in Ashburnham, Massachusetts. Our school district is now part of a network of near-surface remote sensing phenocams that capture and send images of forest, shrub, and grassland vegetation cover at more than 130 diverse sites in North America. Our phenocam provides a digital image every half hour of the mixed forest canopy north from the school, enabling the detection of changes in canopy development, quantified as canopy 'greenness'. As a part of the Phenocam project, students at the K-12 level have expanded the scope of phenological monitoring protocol that is part of the Harvard Forest Schoolyard Ecology Program, Buds, Leaves, and Global Warming. In this protocol, students work with ecologists at Harvard Forest to monitor buds and leaves on schoolyard trees to determine the length of the growing season, giving them the opportunity to be a part of real and important research concerning the critical environmental issue of climate change. Students involved in the Buds, Leaves, and Global Warming study have the opportunity to compare their ground data on budburst, color change, and leaf drop to the phenocam images, as well as to similar forested sites in locations throughout the United States. Lessons have been developed for comparing student data to phenocam images, canopy greenness time series graphs extracted from the images, and satellite data. Lessons addressing map scale and the Urban Heat Island effect will also be available for teachers. This project will greatly enhance the district's Science, Technology, Engineering and Math, (STEM) initiative and further our goal of educating ecologically literate citizens.

Leaf and Life History Traits Predict Plant Growth in a Green Roof Ecosystem

PubMed Central

Lundholm, Jeremy; Heim, Amy; Tran, Stephanie; Smith, Tyler

2014-01-01

Green roof ecosystems are constructed to provide services such as stormwater retention and urban temperature reductions. Green roofs with shallow growing media represent stressful conditions for plant survival, thus plants that survive and grow are important for maximizing economic and ecological benefits. While field trials are essential for selecting appropriate green roof plants, we wanted to determine whether plant leaf traits could predict changes in abundance (growth) to provide a more general framework for plant selection. We quantified leaf traits and derived life-history traits (Grime’s C-S-R strategies) for 13 species used in a four-year green roof experiment involving five plant life forms. Changes in canopy density in monocultures and mixtures containing one to five life forms were determined and related to plant traits using multiple regression. We expected traits related to stress-tolerance would characterize the species that best grew in this relatively harsh setting. While all species survived to the end of the experiment, canopy species diversity in mixture treatments was usually much lower than originally planted. Most species grew slower in mixture compared to monoculture, suggesting that interspecific competition reduced canopy diversity. Species dominant in mixture treatments tended to be fast-growing ruderals and included both native and non-native species. Specific leaf area was a consistently strong predictor of final biomass and the change in abundance in both monoculture and mixture treatments. Some species in contrasting life-form groups showed compensatory dynamics, suggesting that life-form mixtures can maximize resilience of cover and biomass in the face of environmental fluctuations. This study confirms that plant traits can be used to predict growth performance in green roof ecosystems. While rapid canopy growth is desirable for green roofs, maintenance of species diversity may require engineering of conditions that favor less aggressive species. PMID:24978031

The effect of radiometer placement and view on inferred directional and hemispheric radiometric temperatures of an urban canopy

NASA Astrophysics Data System (ADS)

Adderley, C.; Christen, A.; Voogt, J. A.

2015-07-01

Any radiometer at a fixed location has a biased view when observing a convoluted, three-dimensional surface such as an urban canopy. The goal of this contribution is to determine the bias of various sensors views observing a simple urban residential neighbourhood (nadir, oblique, hemispherical) over a 24 hour cycle under clear weather conditions. The error in measuring a longwave radiation flux density (L) and/or inferring surface temperatures (T0) is quantified for different times over a diurnal cycle. Panoramic time-sequential thermography (PTST) data were recorded by a thermal camera on a hydraulic mast above a residential canyon in Vancouver, BC. The data set resolved sub-facet temperature variability of all representative urban facets in a 360° swath repetitively over a 24-hour cycle. This data set is used along with computer graphics and vision techniques to project measured fields of L for a given time and pixel onto texture sheets of a three-dimensional urban surface model at a resolution of centimetres. The resulting data set attributes L of each pixel on the texture sheets to different urban facets and associates facet location, azimuth, slope, material, and sky view factor. The texture sheets of L are used to calculate the complete surface temperature (T0,C) and to simulate the radiation in the field of view (FOV) of narrow and hemispheric radiometers observing the same urban surface (in absence of emissivity and atmospheric effects). The simulated directional (T0,d) and hemispheric (T0,h) radiometric temperatures inferred from various biased views are compared to T0,C. For a range of simulated off-nadir (φ) and azimuth (Ω) angles, T0,d(φ,Ω) and T0,C differ between -2.6 and +2.9 K over the course of the day. The effects of effective anisotropy are highest in the daytime, particularly around sunrise and sunset when different views can lead to differences in T0,d(φ,Ω) that are as high as 3.5 K. For a sensor with a narrow FOV in the nadir of the urban surface, T0,d(φ=0) differs from T0,C by +1.9 K (day) and by -1.6 K (night). Simulations of the FOV of hemispherical, downward-facing pyrgeometers at 270 positions show considerable variations in the measured L and inferred hemispherical radiometeric temperature T0,h as a function of both horizontal placement and height. The root mean squared error (RMSE) between different horizontal positions in retrieving outgoing longwave emittance L↑ decreased exponentially with height, and was 11.2, 6.3 and 2.0 W m-2 at 2, 3, and 5 times the mean building height zb. Generally, above 3.5zb the horizontal positional error is less than the typical accuracy of common pyrgeometers. The average T0,h over 24 h determined from the hemispherical radiometer sufficiently above an urban surface is in close agreement with the average T0,C. However, over the course of the day, the difference between T0,h and T0,C shows an RMSE of 1.7 K (9.4 W m-2) because the relative contributions of facets within the projected FOV of a pyrgeometer do not correspond to their fractions of the complete urban surface.

The effect of radiometer placement and view on inferred directional and hemispheric radiometric temperatures of a urban canopy

NASA Astrophysics Data System (ADS)

Adderley, C.; Christen, A.; Voogt, J. A.

2015-02-01

Any radiometer at a fixed location has a biased view when observing a convoluted, three dimensional surface such as an urban canopy. The goal of this contribution is to determine the bias of various sensors views observing a simple urban residential neighbourhood (nadir, oblique, hemispherical) over a 24 h cycle under clear weather conditions. The error in measuring longwave radiance (L) and/or inferring surface temperatures (T0) is quantified for different times over a diurnal cycle. Panoramic time-sequential thermography (PTST) data was recorded by a thermal camera on a hydraulic mast above a residential canyon in Vancouver, BC. The dataset resolved sub-facet temperature variability of all representative urban facets in a 360° swath repetitively over a 24 h cycle. This dataset is used along with computer graphics and vision techniques to project measured fields of L for a given time and pixel onto texture sheets of a three-dimensional urban surface model at a resolution of centimetres. The resulting dataset attributes L of each pixel on the texture sheets to different urban facets and associates facet location, azimuth, slope, material, and sky view factor. The texture sheets of L are used to calculate the complete surface temperature (T0,C) and to simulate the instantaneous field of view (IFOV) of narrow and hemispheric radiometers observing the same urban surface (in absence of emissivity and atmospheric effects). The simulated directional (T0,d) and hemispheric (T0,h) radiometric temperatures inferred from various biased views are compared to T0,C. For a range of simulated off-nadir (ϕ) and azimuth (Ω) angles, T0,d (ϕ, Ω) and T0,C differ between -2.7 and +2.9 K over the course of the day. The effects of effective anisotropy are highest in the daytime, particularly around sunrise and sunset when different views can lead to differences in T0,d (ϕ, Ω) that are as high as 3.5 K. For a sensor with a narrow IFOV in the nadir of the urban surface, T0,d (ϕ = 0°) differs from T0,C by -2.2 K (day) and by +1.6 K (night). Simulations of the IFOV of hemispherical, downward-facing pyrgeometers at 270 positions show considerable variations in the measured L and inferred hemispherical radiometeric temperature T0,h as a function of both horizontal placement and height. The root mean squared error (RMSE) between different horizontal positions in retrieving outgoing longwave emittance L↑ decreased exponentially with height, and was 11.2, 6.3 and 2.0 W m-2 at 2, 3, and 5 times the mean building height zb. Generally, above 3.5 zb the horizontal positional error is less than the typical accuracy of common pyrgeometers. The average T0,h over 24 h determined from the hemispherical radiometer sufficiently above an urban surface is in close agreement with the average T0,C. However, over the course of the day, the difference between T0,h and T0,C shows an RMSE of 1.8 K (9.9 W m-2) because the relative contributions of facets within the projected IFOV of a pyrgeometer do not correspond to their fractions of the complete urban surface.

Evaluation of a micro-scale wind model's performance over realistic building clusters using wind tunnel experiments

NASA Astrophysics Data System (ADS)

Zhang, Ning; Du, Yunsong; Miao, Shiguang; Fang, Xiaoyi

2016-08-01

The simulation performance over complex building clusters of a wind simulation model (Wind Information Field Fast Analysis model, WIFFA) in a micro-scale air pollutant dispersion model system (Urban Microscale Air Pollution dispersion Simulation model, UMAPS) is evaluated using various wind tunnel experimental data including the CEDVAL (Compilation of Experimental Data for Validation of Micro-Scale Dispersion Models) wind tunnel experiment data and the NJU-FZ experiment data (Nanjing University-Fang Zhuang neighborhood wind tunnel experiment data). The results show that the wind model can reproduce the vortexes triggered by urban buildings well, and the flow patterns in urban street canyons and building clusters can also be represented. Due to the complex shapes of buildings and their distributions, the simulation deviations/discrepancies from the measurements are usually caused by the simplification of the building shapes and the determination of the key zone sizes. The computational efficiencies of different cases are also discussed in this paper. The model has a high computational efficiency compared to traditional numerical models that solve the Navier-Stokes equations, and can produce very high-resolution (1-5 m) wind fields of a complex neighborhood scale urban building canopy (~ 1 km ×1 km) in less than 3 min when run on a personal computer.

Using different assumptions of aerosol mixing state and chemical composition to predict CCN concentrations based on field measurements in urban Beijing

NASA Astrophysics Data System (ADS)

Ren, Jingye; Zhang, Fang; Wang, Yuying; Collins, Don; Fan, Xinxin; Jin, Xiaoai; Xu, Weiqi; Sun, Yele; Cribb, Maureen; Li, Zhanqing

2018-05-01

Understanding the impacts of aerosol chemical composition and mixing state on cloud condensation nuclei (CCN) activity in polluted areas is crucial for accurately predicting CCN number concentrations (NCCN). In this study, we predict NCCN under five assumed schemes of aerosol chemical composition and mixing state based on field measurements in Beijing during the winter of 2016. Our results show that the best closure is achieved with the assumption of size dependent chemical composition for which sulfate, nitrate, secondary organic aerosols, and aged black carbon are internally mixed with each other but externally mixed with primary organic aerosol and fresh black carbon (external-internal size-resolved, abbreviated as EI-SR scheme). The resulting ratios of predicted-to-measured NCCN (RCCN_p/m) were 0.90 - 0.98 under both clean and polluted conditions. Assumption of an internal mixture and bulk chemical composition (INT-BK scheme) shows good closure with RCCN_p/m of 1.0 -1.16 under clean conditions, implying that it is adequate for CCN prediction in continental clean regions. On polluted days, assuming the aerosol is internally mixed and has a chemical composition that is size dependent (INT-SR scheme) achieves better closure than the INT-BK scheme due to the heterogeneity and variation in particle composition at different sizes. The improved closure achieved using the EI-SR and INT-SR assumptions highlight the importance of measuring size-resolved chemical composition for CCN predictions in polluted regions. NCCN is significantly underestimated (with RCCN_p/m of 0.66 - 0.75) when using the schemes of external mixtures with bulk (EXT-BK scheme) or size-resolved composition (EXT-SR scheme), implying that primary particles experience rapid aging and physical mixing processes in urban Beijing. However, our results show that the aerosol mixing state plays a minor role in CCN prediction when the κorg exceeds 0.1.

Seasonal variation of volatile organic compounds exchange above a periurban Holm oak forest on the Mediterranean coast

NASA Astrophysics Data System (ADS)

Savi, Flavia; Juráň, Stanislav; Fares, Silvano

2015-04-01

Bi-directional exchanges of Volatile Organic Compounds (VOCs) were investigated on a Mediterranean Holm oak forest in Castelporziano presidential estate, a peri-urban forest near the coast of Tyrrhenian sea, 20 Km from Rome downtown, Italy. Two field campaigns were carried out in January and August 2014 to explore VOCs fluxes in two seasons with different climate conditions and physiological activity of plants. Concentration of 23 compounds was measured using a proton transfer reaction - mass spectrometer (PTR-MS). These included biogenic products (BVOC - isoprene, monoterpenes), oxygenated BVOC (OVOC - methanol, acetaldehyde acetone) and VOC of anthropogenic origin (AVOC - acetonitrile, benzene, hexenal, toluene, xylenes). Each half-hour, we switched between measurement at high frequency above the canopy and sampling through a 5-levels gradient from soil to above the canopy. We used the eddy covariance technique to calculate fluxes above the canopy, while gradient measurements were used to estimate in-canopy source and sink distribution by applying an Inverse Lagrangian Transport Model (Karl et al., 2004, J.Geophys.Res). Ozone and NOx concentrations were also measured to better correlate VOCs exchanges with this important secondary pollutant. Low temperatures lead to almost negligible BVOC fluxes during Winter. Summer fluxes were largely represented by BVOC (mainly monoterpenes). The highest fluxes (up to 2.4 nmol m-2 s-1) were recorded in the central hour of the day in response to high light and temperature. Oxygenated compounds (methanol and acetone) showed different behaviour during the two seasons: in Winter a net release of these compounds was observed, while in Summer the canopy acted as a sink for OVOC except for the hottest hours when we observed significant emissions. OVOC source-sink distribution analysis helped identifying the canopy layers which mostly contributed to VOCs exchanges, thus underlining the importance of forest canopies in VOCs exchanges in the soil-plant-atmosphere continuum. AVOC (xylene, toluene and benzene) concentration in Winter was double than in Summer, despite the intense vehicular traffic towards the beach nearby the forest stand in August. Both in Winter and Summer, emission of AVOC from the forest were measured, although we excluded a biogenic source but rather a resuspension of compounds previously accumulated at night under shallow atmospheric boundary layer. Photochemically produced ozone was high during the central hours of the day (up to 40 and 70 ppb in Winter and Summer, respectively), while nocturnal concentration went down to less than 20 ppb. Stomata explained almost the totality of ozone fluxes during day (Fares et al., 2014, Agr.Forest.Meteorol), while other non-stomatal sinks including chemical reactions with VOcs were responsible for nocturnal ozone removal. We discuss here the importance of forest canopies in the interaction between VOC and secondary pollutants, such as ozone and NOx in a peculiar Mediterranean site where the sea-land breeze circulation allows a strong mixing between contaminated air from the city and cleaner air from the sea under high UV radiations and air temperatures.

Design and assessment of urban drainage and water reuse systems for the reconstruction of formerly industrial areas: a case in Beijing.

PubMed

Liu, L; Zeng, S; Dong, X; Chen, J

2013-01-01

The Shougang Group is an industrial steel enterprise occupying 800 ha in Beijing that will cease production by 2010. The area will be converted to a new financial and commercial zone. The rebuilding of the water infrastructure in this area should address water shortages in Beijing and retain the industrial landmark of a large cooling water tank. A design framework and an assessment system with 11 indicators were developed for this purpose. Four reconstruction schemes are presented here. Scheme 1 is a traditional system that completely depends on outside the municipal facility. Schemes 2, 3, and 4 are systems to separately discharge greywater and blackwater. Scheme 4 uses a vacuum system that allows the reclamation of nutrients. Schemes 2 and 4 use wetland-treated greywater to fill the water tank. Scheme 3 reuses greywater for toilets after on-site treatment. Scheme 2 is recommended due to its lower cost, greater environmental benefit, moderate resource reclamation, and higher technical feasibility.