Achieving HIV risk reduction through HealthMpowerment.org, a user-driven eHealth intervention for young Black men who have sex with men and transgender women who have sex with men

PubMed Central

Muessig, Kathryn E.; Baltierra, Nina B.; Pike, Emily C.; LeGrand, Sara; Hightow-Weidman, Lisa B.

2014-01-01

Young, Black men who have sex with men and transgender women who have sex with men (YBMSM/TW) are at disproportionate risk for HIV and other sexually transmitted infections (HIV/STI). HealthMpowerment.org (HMP) is a mobile phone optimised online intervention that utilises behaviour change and gaming theories to reduce risky sexual behaviours and build community among HIV-positive and negative YBMSM/TW. The intervention is user-driven, provides social support, and utilises a point reward system. A four-week pilot trial was conducted with a diverse group of 15 YBMSM/TW. During exit interviews, participants described how HMP components led to behaviour changes such as asking partners' sexual history, increased condom use, and HIV/STI testing. The user-driven structure, interactivity, and rewards appeared to facilitate sustained user engagement and the mobile platform provided relevant information in real-time. Participants described the reward elements of exceeding their previous scores and earning points toward prizes as highly motivating. HMP showed promise for being able to deliver a sufficient intervention dose and we found a trend toward higher dose received and more advanced stages of behaviour change. In this pilot trial, HMP was well accepted and demonstrates promise for translating virtual intervention engagement into actual behaviour change to reduce HIV risk behaviours. PMID:25593616

Achieving HIV risk reduction through HealthMpowerment.org, a user-driven eHealth intervention for young Black men who have sex with men and transgender women who have sex with men.

PubMed

Muessig, Kathryn E; Baltierra, Nina B; Pike, Emily C; LeGrand, Sara; Hightow-Weidman, Lisa B

Young, Black men who have sex with men and transgender women who have sex with men (YBMSM/TW) are at disproportionate risk for HIV and other sexually transmitted infections (HIV/STI). HealthMpowerment.org (HMP) is a mobile phone optimised online intervention that utilises behaviour change and gaming theories to reduce risky sexual behaviours and build community among HIV-positive and negative YBMSM/TW. The intervention is user-driven, provides social support, and utilises a point reward system. A four-week pilot trial was conducted with a diverse group of 15 YBMSM/TW. During exit interviews, participants described how HMP components led to behaviour changes such as asking partners' sexual history, increased condom use, and HIV/STI testing. The user-driven structure, interactivity, and rewards appeared to facilitate sustained user engagement and the mobile platform provided relevant information in real-time. Participants described the reward elements of exceeding their previous scores and earning points toward prizes as highly motivating. HMP showed promise for being able to deliver a sufficient intervention dose and we found a trend toward higher dose received and more advanced stages of behaviour change. In this pilot trial, HMP was well accepted and demonstrates promise for translating virtual intervention engagement into actual behaviour change to reduce HIV risk behaviours.

A user-driven treadmill control scheme for simulating overground locomotion.

PubMed

Kim, Jonghyun; Stanley, Christopher J; Curatalo, Lindsey A; Park, Hyung-Soon

2012-01-01

Treadmill-based locomotor training should simulate overground walking as closely as possible for optimal skill transfer. The constant speed of a standard treadmill encourages automaticity rather than engagement and fails to simulate the variable speeds encountered during real-world walking. To address this limitation, this paper proposes a user-driven treadmill velocity control scheme that allows the user to experience natural fluctuations in walking velocity with minimal unwanted inertial force due to acceleration/deceleration of the treadmill belt. A smart estimation limiter in the scheme effectively attenuates the inertial force during velocity changes. The proposed scheme requires measurement of pelvic and swing foot motions, and is developed for a treadmill of typical belt length (1.5 m). The proposed scheme is quantitatively evaluated here with four healthy subjects by comparing it with the most advanced control scheme identified in the literature.

Geospatial optimization of siting large-scale solar projects

USGS Publications Warehouse

Macknick, Jordan; Quinby, Ted; Caulfield, Emmet; Gerritsen, Margot; Diffendorfer, James E.; Haines, Seth S.

2014-01-01

guidelines by being user-driven, transparent, interactive, capable of incorporating multiple criteria, and flexible. This work provides the foundation for a dynamic siting assistance tool that can greatly facilitate siting decisions among multiple stakeholders.

Office of university affairs management information system: Users guide and documentation

NASA Technical Reports Server (NTRS)

Distin, J.; Goodwin, D.; Greene, W. A.

1977-01-01

Data on the NASA-University relationship are reported that encompass research in over 600 schools through several thousand grants and contracts. This user-driven system is capable of producing a variety of cyclical and query-type reports describing the total NASA-University profile. The capabilities, designed as part of the system, require a minimum of user maintenance in order to ensure system efficiency and data validity to meet the recurrent Statutory and Executive Branch information requirements as well as ad hoc inquiries from NASA general management, Congress, other Federal agencies, private sector organizations, universities and individuals. The data base contains information on each university, the individual projects and the financial details, current and historic, on all contracts and grants. Complete details are given on the system from its unique design features to the actual steps required for daily operation.

Installed Base as a Facilitator for User-Driven Innovation: How Can User Innovation Challenge Existing Institutional Barriers?

PubMed Central

Andersen, Synnøve Thomassen; Jansen, Arild

2012-01-01

The paper addresses an ICT-based, user-driven innovation process in the health sector in rural areas in Norway. The empirical base is the introduction of a new model for psychiatric health provision. This model is supported by a technical solution based on mobile phones that is aimed to help the communication between professional health personnel and patients. This innovation was made possible through the use of standard mobile technology rather than more sophisticated systems. The users were heavily involved in the development work. Our analysis shows that by thinking simple and small-scale solutions, including to take the user's needs and premises as a point of departure rather than focusing on advanced technology, the implementation process was made possible. We show that by combining theory on information infrastructures, user-oriented system development, and innovation in a three-layered analytical framework, we can explain the interrelationship between technical, organizational, and health professional factors that made this innovation a success. PMID:23304134

User-Driven Quality Certification of Workplace Software, the UsersAward Experience

DTIC Science & Technology

2004-06-01

the set of criteria and the chosen level of approval was sufficiently balanced . Furthermore, the fact that both software providers experienced... Worklife - Building Social Capacity - European Approaches, Edition sigma Berlin. Lind, T. (2002). IT-kartan, användare och IT-system i svenskt

Imagining Tomorrow's Future Today

ERIC Educational Resources Information Center

St. George, Art

2007-01-01

Today, at the end of 2007, there are evident consolidations in wireless, storage, and virtualization and the path forward seems clearer now than previously. Trends from last year continue strongly, particularly Web 2.0 and the shift to user-driven environments and Internet sites where significant data and video processing is available to those…

A User-Driven Annotation Framework for Scientific Data

ERIC Educational Resources Information Center

Li, Qinglan

2013-01-01

Annotations play an increasingly crucial role in scientific exploration and discovery, as the amount of data and the level of collaboration among scientists increases. There are many systems today focusing on annotation management, querying, and propagation. Although all such systems are implemented to take user input (i.e., the annotations…

A PILOT PROJECT TO DETECT AND PREDICT HARMFUL ALGAL BLOOMS IN THE NORTHERN GULF OF MEXICO

EPA Science Inventory

More timely access to data and information on the initiation, evolution and effects of harmful algal blooms can reduce adverse impacts on valued natural resources and human health. To achieve this, a workshop was held to develop a user-driven, end-to-end (measurements to applicat...

From the Users' Perspective-The UCSD Libraries User Survey Project.

ERIC Educational Resources Information Center

Talbot, Dawn E.; Lowell, Gerald R.; Martin, Kerry

1998-01-01

Discussion of a user-driven survey conducted at the University of California, San Diego libraries focuses on the methodology that resulted in a high response rate. Highlights goals for the survey, including acceptance of data by groups outside the library and for benchmarking data; planning; user population; and questionnaire development. (LRW)

User-Driven Planning for Digital-Image Delivery

ERIC Educational Resources Information Center

Pisciotta, Henry; Halm, Michael J.; Dooris, Michael J.

2006-01-01

This article draws on two projects funded by the Andrew W. Mellon Foundation concerning the ways colleges and universities can support the legitimate sharing of digital learning resources for scholarly use. The 2001-03 Visual Image User Study (VIUS) assessed the scholarly needs of digital image users-faculty, staff, and students. That study led to…

Developing a Competence-Based Addiction Medicine Curriculum in Indonesia: The Training Needs Assessment

ERIC Educational Resources Information Center

Pinxten, W. J. L.; De Jong, C.; Hidayat, T.; Istiqomah, A. N.; Achmad, Y. M.; Raya, R. P.; Norviatin, D.; Siregar, I. M. P.

2011-01-01

Indonesia has one of the fastest growing, injecting drugs user-driven, human immunodeficiency virus (HIV) epidemics in Asia. Coverage of needle and syringe programs (NSPs), opioid substitution therapy (OST), and antiretroviral treatment (ART) is increasing, but is still low, whereas professional training in addiction medicine is not yet…

Improving the efficiency of a user-driven learning system with reconfigurable hardware. Application to DNA splicing.

PubMed

Lemoine, E; Merceron, D; Sallantin, J; Nguifo, E M

1999-01-01

This paper describes a new approach to problem solving by splitting up problem component parts between software and hardware. Our main idea arises from the combination of two previously published works. The first one proposed a conceptual environment of concept modelling in which the machine and the human expert interact. The second one reported an algorithm based on reconfigurable hardware system which outperforms any kind of previously published genetic data base scanning hardware or algorithms. Here we show how efficient the interaction between the machine and the expert is when the concept modelling is based on reconfigurable hardware system. Their cooperation is thus achieved with an real time interaction speed. The designed system has been partially applied to the recognition of primate splice junctions sites in genetic sequences.

The Rangeland Vegetation Simulator: A user-driven system for quantifying production, succession, disturbance and fuels in non-forest environments

Treesearch

Matt Reeves; Leonardo Frid

2016-01-01

Rangeland landscapes occupy roughly 662 million acres in the coterminous U.S. (Reeves and Mitchell 2011) and their vegetation responds quickly to climate and management, with high relative growth rates and inter-annual variability. Current national decision support systems in the U.S. such as the Interagency Fuels Treatment Decision Support System (IFT-DSS) require...

The implementation and use of Ada on distributed systems with high reliability requirements

NASA Technical Reports Server (NTRS)

Knight, J. C.

1988-01-01

The use and implementation of Ada were investigated in distributed environments in which reliability is the primary concern. In particular, the focus was on the possibility that a distributed system may be programmed entirely in Ada so that the individual tasks of the system are unconcerned with which processors are being executed, and that failures may occur in the software and underlying hardware. A secondary interest is in the performance of Ada systems and how that performance can be gauged reliably. Primary activities included: analysis of the original approach to recovery in distributed Ada programs using the Advanced Transport Operating System (ATOPS) example; review and assessment of the original approach which was found to be capable of improvement; development of a refined approach to recovery that was applied to the ATOPS example; and design and development of a performance assessment scheme for Ada programs based on a flexible user-driven benchmarking system.

Integrating Facebook in Upper Secondary Biology Instruction: A Case Study of Students' Situational Interest and Participation in Learning Communication

ERIC Educational Resources Information Center

Dohn, Niels Bonderup; Dohn, Nina Bonderup

2017-01-01

The sciences are often perceived by students as irrelevant as they do not see the content of science as related to their daily lives. Web 2.0-mediated activities are characterized by user-driven content production, collaboration, and multi-way communication. It has been proposed that employing Web 2.0 in educational activities will promote richer…

Interactive High-Relief Reconstruction for Organic and Double-Sided Objects from a Photo.

PubMed

Yeh, Chih-Kuo; Huang, Shi-Yang; Jayaraman, Pradeep Kumar; Fu, Chi-Wing; Lee, Tong-Yee

2017-07-01

We introduce an interactive user-driven method to reconstruct high-relief 3D geometry from a single photo. Particularly, we consider two novel but challenging reconstruction issues: i) common non-rigid objects whose shapes are organic rather than polyhedral/symmetric, and ii) double-sided structures, where front and back sides of some curvy object parts are revealed simultaneously on image. To address these issues, we develop a three-stage computational pipeline. First, we construct a 2.5D model from the input image by user-driven segmentation, automatic layering, and region completion, handling three common types of occlusion. Second, users can interactively mark-up slope and curvature cues on the image to guide our constrained optimization model to inflate and lift up the image layers. We provide real-time preview of the inflated geometry to allow interactive editing. Third, we stitch and optimize the inflated layers to produce a high-relief 3D model. Compared to previous work, we can generate high-relief geometry with large viewing angles, handle complex organic objects with multiple occluded regions and varying shape profiles, and reconstruct objects with double-sided structures. Lastly, we demonstrate the applicability of our method on a wide variety of input images with human, animals, flowers, etc.

An architecture for a continuous, user-driven, and data-driven application of clinical guidelines and its evaluation.

PubMed

Shalom, Erez; Shahar, Yuval; Lunenfeld, Eitan

2016-02-01

Design, implement, and evaluate a new architecture for realistic continuous guideline (GL)-based decision support, based on a series of requirements that we have identified, such as support for continuous care, for multiple task types, and for data-driven and user-driven modes. We designed and implemented a new continuous GL-based support architecture, PICARD, which accesses a temporal reasoning engine, and provides several different types of application interfaces. We present the new architecture in detail in the current paper. To evaluate the architecture, we first performed a technical evaluation of the PICARD architecture, using 19 simulated scenarios in the preeclampsia/toxemia domain. We then performed a functional evaluation with the help of two domain experts, by generating patient records that simulate 60 decision points from six clinical guideline-based scenarios, lasting from two days to four weeks. Finally, 36 clinicians made manual decisions in half of the scenarios, and had access to the automated GL-based support in the other half. The measures used in all three experiments were correctness and completeness of the decisions relative to the GL. Mean correctness and completeness in the technical evaluation were 1±0.0 and 0.96±0.03 respectively. The functional evaluation produced only several minor comments from the two experts, mostly regarding the output's style; otherwise the system's recommendations were validated. In the clinically oriented evaluation, the 36 clinicians applied manually approximately 41% of the GL's recommended actions. Completeness increased to approximately 93% when using PICARD. Manual correctness was approximately 94.5%, and remained similar when using PICARD; but while 68% of the manual decisions included correct but redundant actions, only 3% of the actions included in decisions made when using PICARD were redundant. The PICARD architecture is technically feasible and is functionally valid, and addresses the realistic continuous GL-based application requirements that we have defined; in particular, the requirement for care over significant time frames. The use of the PICARD architecture in the domain we examined resulted in enhanced completeness and in reduction of redundancies, and is potentially beneficial for general GL-based management of chronic patients. Copyright © 2015 Elsevier Inc. All rights reserved.

Mechanism Design for Incentivizing Social Media Contributions

NASA Astrophysics Data System (ADS)

Singh, Vivek K.; Jain, Ramesh; Kankanhalli, Mohan

Despite recent advancements in user-driven social media platforms, tools for studying user behavior patterns and motivations remain primitive. We highlight the voluntary nature of user contributions and that users can choose when (and when not) to contribute to the common media pool. A Game theoretic framework is proposed to study the dynamics of social media networks where contribution costs are individual but gains are common. We model users as rational selfish agents, and consider domain attributes like voluntary participation, virtual reward structure, network effect, and public-sharing to model the dynamics of this interaction. The created model describes the most appropriate contribution strategy from each user's perspective and also highlights issues like 'free-rider' problem and individual rationality leading to irrational (i.e. sub-optimal) group behavior. We also consider the perspective of the system designer who is interested in finding the best incentive mechanisms to influence the selfish end-users so that the overall system utility is maximized. We propose and compare multiple mechanisms (based on optimal bonus payment, social incentive leveraging, and second price auction) to study how a system designer can exploit the selfishness of its users, to design incentive mechanisms which improve the overall task-completion probability and system performance, while possibly still benefiting the individual users.

A Tool for Automatic Verification of Real-Time Expert Systems

NASA Technical Reports Server (NTRS)

Traylor, B.; Schwuttke, U.; Quan, A.

1994-01-01

The creation of an automated, user-driven tool for expert system development, validation, and verification is curretly onoging at NASA's Jet Propulsion Laboratory. In the new age of faster, better, cheaper missions, there is an increased willingness to utilize embedded expert systems for encapsulating and preserving mission expertise in systems which combine conventional algorithmic processing and artifical intelligence. The once-questioned role of automation in spacecraft monitoring is now becoming one of increasing importance.

User-Driven Geolocation of Untagged Desert Imagery Using Digital Elevation Models (Open Access)

DTIC Science & Technology

2013-09-12

IEEE International Conference on, pages 3677–3680. IEEE, 2011. [13] W. Zhang and J. Kosecka. Image based localization in urban environments. In 3D ...non- urban environments such as deserts. Our system generates synthetic skyline views from a DEM and extracts stable concavity-based features from these...fine as 100m2. 1. Introduction Automatic geolocation of imagery has many exciting use cases. For example, such a tool could semantically orga- nize

User-Driven Geolocation of Untagged Desert Imagery Using Digital Elevation Models

DTIC Science & Technology

2013-01-01

Conference on, pages 3677–3680. IEEE, 2011. [13] W. Zhang and J. Kosecka. Image based localization in urban environments. In 3D Data Processing...non- urban environments such as deserts. Our system generates synthetic skyline views from a DEM and extracts stable concavity-based features from these...fine as 100m2. 1. Introduction Automatic geolocation of imagery has many exciting use cases. For example, such a tool could semantically orga- nize

Enhancements to a Superconducting Quantum Interference Device (SQUID) Multiplexer Readout and Control System

NASA Technical Reports Server (NTRS)

Forgione, J.; Benford, D. J.; Buchanan, E. D.; Moseley, S. H.; Rebar, J.; Shafer, R. A.

2004-01-01

Far-infrared detector arrays such as the 16x32 superconducting bolometer array for the SAFIRE instrument (flying on the SOFIA airborne observatory) require systems of readout and control electronics to provide translation between a user-driven, digital PC and the cold, analog world of the cryogenic detector. In 2001, the National Institute of Standards and Technology (NIST) developed their Mark III electronics for purposes of control and readout of their 1x32 SQUID Multiplexer chips. We at NASA s Goddard Space Flight Center acquired a Mark 111 system and subsequently designed upgrades to suit our and our collaborators purposes. We developed an arbitrary, programmable multiplexing system that allows the user to cycle through rows in a SQUID array in an infinite number of combinations. We provided hooks in the Mark III system to allow readout of signals from outside the Mark 111 system, such as telescope status information. Finally, we augmented the heart of the system with a new feedback algorithm implementation, flexible diagnostic tools, and informative telemetry.

Enhancements to a superconducting quantum interference device (SQUID) multiplexer readout and control system

NASA Astrophysics Data System (ADS)

Forgione, Joshua B.; Benford, Dominic J.; Buchanan, Ernest D.; Moseley, S. H., Jr.; Rebar, Joyce; Shafer, Richard A.

2004-10-01

Far-infrared detector arrays such as the 16x32 superconducting bolometer array for the SAFIRE instrument (flying on the SOFIA airborne observatory) require systems of readout and control electronics to provide translation between a user-driven, digital PC and the cold, analog world of the cryogenic detector. In 2001, the National Institute of Standards and Technology (NIST) developed their Mark III electronics for purposes of control and readout of their 1x32 SQUID Multiplexer chips. We at NASA's Goddard Space Flight Center acquired a Mark III system and subsequently designed upgrades to suit our and our collaborators' purposes. We developed an arbitrary, programmable multiplexing system that allows the user to cycle through rows in a SQUID array in an infinite number of combinations. We provided 'hooks' in the Mark III system to allow readout of signals from outside the Mark III system, such as telescope status information. Finally, we augmented the heart of the system with a new feedback algorithm implementation, flexible diagnostic tools, and informative telemetry.

Visual Analytics Tools for Sustainable Lifecycle Design: Current Status, Challenges, and Future Opportunities.

PubMed

Ramanujan, Devarajan; Bernstein, William Z; Chandrasegaran, Senthil K; Ramani, Karthik

2017-01-01

The rapid rise in technologies for data collection has created an unmatched opportunity to advance the use of data-rich tools for lifecycle decision-making. However, the usefulness of these technologies is limited by the ability to translate lifecycle data into actionable insights for human decision-makers. This is especially true in the case of sustainable lifecycle design (SLD), as the assessment of environmental impacts, and the feasibility of making corresponding design changes, often relies on human expertise and intuition. Supporting human sense-making in SLD requires the use of both data-driven and user-driven methods while exploring lifecycle data. A promising approach for combining the two is through the use of visual analytics (VA) tools. Such tools can leverage the ability of computer-based tools to gather, process, and summarize data along with the ability of human-experts to guide analyses through domain knowledge or data-driven insight. In this paper, we review previous research that has created VA tools in SLD. We also highlight existing challenges and future opportunities for such tools in different lifecycle stages-design, manufacturing, distribution & supply chain, use-phase, end-of-life, as well as life cycle assessment. Our review shows that while the number of VA tools in SLD is relatively small, researchers are increasingly focusing on the subject matter. Our review also suggests that VA tools can address existing challenges in SLD and that significant future opportunities exist.

User-driven conversations about dialysis through Facebook: A qualitative thematic analysis.

PubMed

Ahmed, Salim; Haines-Saah, Rebecca J; Afzal, Arfan R; Tam-Tham, Helen; Al Mamun, Mohammad; Hemmelgarn, Brenda R; Turin, Tanvir C

2017-04-01

As one of the most popular social networking sites in the world, Facebook has strong potential to enable peer support and the user-driven sharing of health information. We carried out a qualitative thematic analysis of the wall posts of a public Facebook group focused on dialysis to identify some of the major themes discussed. We searched Facebook using the word 'dialysis'. A Facebook group (Dialysis Discussion Uncensored) with the highest number of members was selected amongst publicly available forums related to dialysis and operated in English (http://www.facebook.com/groups/DialysisUncensored). Two researchers independently extracted information on features of the group including purpose, group members and the user-generated posts on the group wall. Posts were further analysed to develop major themes. Characteristics of a Facebook group based on its participants and activities are presented. Three themes are described with representative quotations. In a period of 2 weeks, we found 1257 wall posts with total of 31 636 likes and 15 972 comments. All messages were in English, and the majority of the participants were dialysis patients. However, we observed the participation of family members and care providers as well. Posts were categorized into three major themes: sharing information, seeking and providing emotional and social support and sharing experience. Findings of this study provide an example of how a social networking platform can enable patients and their families to share information and to encourage peer-based support for managing dialysis-related experiences. © 2016 Asian Pacific Society of Nephrology.

Implementing a user-driven online quality improvement toolkit for cancer care.

PubMed

Luck, Jeff; York, Laura S; Bowman, Candice; Gale, Randall C; Smith, Nina; Asch, Steven M

2015-05-01

Peer-to-peer collaboration within integrated health systems requires a mechanism for sharing quality improvement lessons. The Veterans Health Administration (VA) developed online compendia of tools linked to specific cancer quality indicators. We evaluated awareness and use of the toolkits, variation across facilities, impact of social marketing, and factors influencing toolkit use. A diffusion of innovations conceptual framework guided the collection of user activity data from the Toolkit Series SharePoint site and an online survey of potential Lung Cancer Care Toolkit users. The VA Toolkit Series site had 5,088 unique visitors in its first 22 months; 5% of users accounted for 40% of page views. Social marketing communications were correlated with site usage. Of survey respondents (n = 355), 54% had visited the site, of whom 24% downloaded at least one tool. Respondents' awareness of the lung cancer quality performance of their facility, and facility participation in quality improvement collaboratives, were positively associated with Toolkit Series site use. Facility-level lung cancer tool implementation varied widely across tool types. The VA Toolkit Series achieved widespread use and a high degree of user engagement, although use varied widely across facilities. The most active users were aware of and active in cancer care quality improvement. Toolkit use seemed to be reinforced by other quality improvement activities. A combination of user-driven tool creation and centralized toolkit development seemed to be effective for leveraging health information technology to spread disease-specific quality improvement tools within an integrated health care system. Copyright © 2015 by American Society of Clinical Oncology.

Semi-automated segmentation of neuroblastoma nuclei using the gradient energy tensor: a user driven approach

NASA Astrophysics Data System (ADS)

Kromp, Florian; Taschner-Mandl, Sabine; Schwarz, Magdalena; Blaha, Johanna; Weiss, Tamara; Ambros, Peter F.; Reiter, Michael

2015-02-01

We propose a user-driven method for the segmentation of neuroblastoma nuclei in microscopic fluorescence images involving the gradient energy tensor. Multispectral fluorescence images contain intensity and spatial information about antigene expression, fluorescence in situ hybridization (FISH) signals and nucleus morphology. The latter serves as basis for the detection of single cells and the calculation of shape features, which are used to validate the segmentation and to reject false detections. Accurate segmentation is difficult due to varying staining intensities and aggregated cells. It requires several (meta-) parameters, which have a strong influence on the segmentation results and have to be selected carefully for each sample (or group of similar samples) by user interactions. Because our method is designed for clinicians and biologists, who may have only limited image processing background, an interactive parameter selection step allows the implicit tuning of parameter values. With this simple but intuitive method, segmentation results with high precision for a large number of cells can be achieved by minimal user interaction. The strategy was validated on handsegmented datasets of three neuroblastoma cell lines.

User-Driven Workflow for Modeling, Monitoring, Product Development, and Flood Map Delivery Using Satellites for Daily Coverage Over Texas May-June 2015

NASA Astrophysics Data System (ADS)

Green, D. S.; Frye, S. W.; Wells, G. L.; Adler, R. F.; Brakenridge, R.; Bolten, J. D.; Murray, J. J.; Slayback, D. A.; Kirschbaum, D.; Wu, H.; Cappelaere, P. G.; Schumann, G.; Howard, T.; Flamig, Z.; Clark, R. A.; Stough, T.; Chini, M.; Matgen, P.

2015-12-01

Intense rainfall during late April and early May 2015 in Texas and Oklahoma led to widespread flooding in several river basins in that region. Texas state agencies were activated for the May-June floods and severe weather event that ensued for six weeks from May 8 until June 19 following Tropical Storm Bill. This poster depicts a case study where modeling flood potential informed decision making authorities for user-driven high resolution satellite acquisitions over the most critical areas and how experimental flood mapping techniques provided the capability for daily on-going monitoring of these events through the use of increased automation. Recent improvements in flood models resulting from higher frequency updates, better spatial resolution, and increased accuracy of now cast and forecast precipitation products coupled with advanced technology to improve situational awareness for decision makers. These advances enabled satellites to be tasked, data products to be developed and distributed, and feedback loops between the emergency authorities, satellite operators, and mapping researchers to deliver a daily stream of relevant products that informed deployment of emergency resources and improved management of the large-scale event across the local, state, and national levels. This collaboration was made possible through inter-agency cooperation on an international scale through the Committee on Earth Observation Satellites Flood Pilot activity that is supported in the USA by NASA, NOAA, and USGS and includes numerous civilian space agency assets from the European Space Agency along with national agencies from Italy, France, Germany, Japan, and others. The poster describes the inter-linking technology infrastructure, the development and delivery of mapping products, and the lessons learned for product improvement in the future.

The Stanford Data Miner: a novel approach for integrating and exploring heterogeneous immunological data.

PubMed

Siebert, Janet C; Munsil, Wes; Rosenberg-Hasson, Yael; Davis, Mark M; Maecker, Holden T

2012-03-28

Systems-level approaches are increasingly common in both murine and human translational studies. These approaches employ multiple high information content assays. As a result, there is a need for tools to integrate heterogeneous types of laboratory and clinical/demographic data, and to allow the exploration of that data by aggregating and/or segregating results based on particular variables (e.g., mean cytokine levels by age and gender). Here we describe the application of standard data warehousing tools to create a novel environment for user-driven upload, integration, and exploration of heterogeneous data. The system presented here currently supports flow cytometry and immunoassays performed in the Stanford Human Immune Monitoring Center, but could be applied more generally. Users upload assay results contained in platform-specific spreadsheets of a defined format, and clinical and demographic data in spreadsheets of flexible format. Users then map sample IDs to connect the assay results with the metadata. An OLAP (on-line analytical processing) data exploration interface allows filtering and display of various dimensions (e.g., Luminex analytes in rows, treatment group in columns, filtered on a particular study). Statistics such as mean, median, and N can be displayed. The views can be expanded or contracted to aggregate or segregate data at various levels. Individual-level data is accessible with a single click. The result is a user-driven system that permits data integration and exploration in a variety of settings. We show how the system can be used to find gender-specific differences in serum cytokine levels, and compare them across experiments and assay types. We have used the tools and techniques of data warehousing, including open-source business intelligence software, to support investigator-driven data integration and mining of diverse immunological data.

The Stanford Data Miner: a novel approach for integrating and exploring heterogeneous immunological data

PubMed Central

2012-01-01

Background Systems-level approaches are increasingly common in both murine and human translational studies. These approaches employ multiple high information content assays. As a result, there is a need for tools to integrate heterogeneous types of laboratory and clinical/demographic data, and to allow the exploration of that data by aggregating and/or segregating results based on particular variables (e.g., mean cytokine levels by age and gender). Methods Here we describe the application of standard data warehousing tools to create a novel environment for user-driven upload, integration, and exploration of heterogeneous data. The system presented here currently supports flow cytometry and immunoassays performed in the Stanford Human Immune Monitoring Center, but could be applied more generally. Results Users upload assay results contained in platform-specific spreadsheets of a defined format, and clinical and demographic data in spreadsheets of flexible format. Users then map sample IDs to connect the assay results with the metadata. An OLAP (on-line analytical processing) data exploration interface allows filtering and display of various dimensions (e.g., Luminex analytes in rows, treatment group in columns, filtered on a particular study). Statistics such as mean, median, and N can be displayed. The views can be expanded or contracted to aggregate or segregate data at various levels. Individual-level data is accessible with a single click. The result is a user-driven system that permits data integration and exploration in a variety of settings. We show how the system can be used to find gender-specific differences in serum cytokine levels, and compare them across experiments and assay types. Conclusions We have used the tools and techniques of data warehousing, including open-source business intelligence software, to support investigator-driven data integration and mining of diverse immunological data. PMID:22452993

Young men’s attitudes and behaviour in relation to mental health and technology: implications for the development of online mental health services

PubMed Central

2013-01-01

Background This mixed-methods study was designed to explore young Australian men’s attitudes and behaviour in relation to mental health and technology use to inform the development of online mental health services for young men. Methods National online survey of 486 males (aged 16 to 24) and 17 focus groups involving 118 males (aged 16 to 24). Results Young men are heavy users of technology, particularly when it comes to entertainment and connecting with friends, but they are also using technology for finding information and support. The focus group data suggested that young men would be less likely to seek professional help for themselves, citing a preference for self-help and action-oriented strategies instead. Most survey participants reported that they have sought help for a problem online and were satisfied with the help they received. Focus group participants identified potential strategies for how technology could be used to overcome the barriers to help-seeking for young men. Conclusions The key challenge for online mental health services is to design interventions specifically for young men that are action-based, focus on shifting behaviour and stigma, and are not simply about increasing mental health knowledge. Furthermore, such interventions should be user-driven, informed by young men’s views and everyday technology practices, and leverage the influence of peers. PMID:23601273

Young men's attitudes and behaviour in relation to mental health and technology: implications for the development of online mental health services.

PubMed

Ellis, Louise A; Collin, Philippa; Hurley, Patrick J; Davenport, Tracey A; Burns, Jane M; Hickie, Ian B

2013-04-20

This mixed-methods study was designed to explore young Australian men's attitudes and behaviour in relation to mental health and technology use to inform the development of online mental health services for young men. National online survey of 486 males (aged 16 to 24) and 17 focus groups involving 118 males (aged 16 to 24). Young men are heavy users of technology, particularly when it comes to entertainment and connecting with friends, but they are also using technology for finding information and support. The focus group data suggested that young men would be less likely to seek professional help for themselves, citing a preference for self-help and action-oriented strategies instead. Most survey participants reported that they have sought help for a problem online and were satisfied with the help they received. Focus group participants identified potential strategies for how technology could be used to overcome the barriers to help-seeking for young men. The key challenge for online mental health services is to design interventions specifically for young men that are action-based, focus on shifting behaviour and stigma, and are not simply about increasing mental health knowledge. Furthermore, such interventions should be user-driven, informed by young men's views and everyday technology practices, and leverage the influence of peers.

Design and simulation of the direct drive servo system

NASA Astrophysics Data System (ADS)

Ren, Changzhi; Liu, Zhao; Song, Libin; Yi, Qiang; Chen, Ken; Zhang, Zhenchao

2010-07-01

As direct drive technology is finding their way into telescope drive designs for its many advantages, it would push to more reliable and cheaper solutions for future telescope complex motion system. However, the telescope drive system based on the direct drive technology is one high integrated electromechanical system, which one complex electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. The telescope is one ultra-exact, ultra-speed, high precision and huge inertial instrument, which the direct torque motor adopted by the telescope drive system is different from traditional motor. This paper explores the design process and some simulation results are discussed.

Usage of an Exercise App in the Care for People With Osteoarthritis: User-Driven Exploratory Study

PubMed Central

2018-01-01

Background Exercise has proven to reduce pain and increase quality of life among people living with osteoarthritis (OA). However, one major challenge is adherence to exercise once supervision ends. Objective This study aimed to identify mental and physical barriers and motivational and social aspects of training at home, and to test or further develop an exercise app. Methods The study was inspired from participatory design, engaging users in the research process. Data were collected through focus groups and workshops, and analyzed by systematic text condensation. Results Three main themes were found: competition as motivation, training together, and barriers. The results revealed that the participants wanted to do their training and had knowledge on exercise and pain but found it hard to motivate themselves. They missed the observation, comments, and encouragement by the supervising physiotherapist as well as their peers. Ways to optimize the training app were identified during the workshops as participants shared their experience. Conclusions This study concludes that the long-term continuation of exercising for patients with OA could be improved with the use of a technology tailored to users’ needs, including motivational and other behavioral factors. PMID:29326092

Interactive Streamline Exploration and Manipulation Using Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tong, Xin; Chen, Chun-Ming; Shen, Han-Wei

2015-01-12

Occlusion presents a major challenge in visualizing three-dimensional flow fields with streamlines. Displaying too many streamlines at once makes it difficult to locate interesting regions, but displaying too few streamlines risks missing important features. A more ideal streamline exploration model is to allow the viewer to freely move across the field that has been populated with interesting streamlines and pull away the streamlines that cause occlusion so that the viewer can inspect the hidden ones in detail. In this paper, we present a streamline deformation algorithm that supports such user-driven interaction with three-dimensional flow fields. We define a view-dependent focus+contextmore » technique that moves the streamlines occluding the focus area using a novel displacement model. To preserve the context surrounding the user-chosen focus area, we propose two shape models to define the transition zone for the surrounding streamlines, and the displacement of the contextual streamlines is solved interactively with a goal of preserving their shapes as much as possible. Based on our deformation model, we design an interactive streamline exploration tool using a lens metaphor. Our system runs interactively so that users can move their focus and examine the flow field freely.« less

Progressive Visual Analytics: User-Driven Visual Exploration of In-Progress Analytics.

PubMed

Stolper, Charles D; Perer, Adam; Gotz, David

2014-12-01

As datasets grow and analytic algorithms become more complex, the typical workflow of analysts launching an analytic, waiting for it to complete, inspecting the results, and then re-Iaunching the computation with adjusted parameters is not realistic for many real-world tasks. This paper presents an alternative workflow, progressive visual analytics, which enables an analyst to inspect partial results of an algorithm as they become available and interact with the algorithm to prioritize subspaces of interest. Progressive visual analytics depends on adapting analytical algorithms to produce meaningful partial results and enable analyst intervention without sacrificing computational speed. The paradigm also depends on adapting information visualization techniques to incorporate the constantly refining results without overwhelming analysts and provide interactions to support an analyst directing the analytic. The contributions of this paper include: a description of the progressive visual analytics paradigm; design goals for both the algorithms and visualizations in progressive visual analytics systems; an example progressive visual analytics system (Progressive Insights) for analyzing common patterns in a collection of event sequences; and an evaluation of Progressive Insights and the progressive visual analytics paradigm by clinical researchers analyzing electronic medical records.

Using naturalistic driving films as a design tool for investigating driver requirements in HMI design for ADAS.

PubMed

Wang, Minjuan; Sun, Dong; Chen, Fang

2012-01-01

In recent years, there are many naturalistic driving projects have been conducted, such as the 100-Car Project (Naturalistic Driving study in United State), EuroFOT(European Large-Scale Field Operational Tests on Vehicle Systems), SeMi- FOT(Sweden Michigan Naturalistic Field Operational Test and etc. However, those valuable naturalistic driving data hasn't been applied into Human-machine Interaction (HMI) design for Advanced Driver Assistance Systems (ADAS), a good HMI design for ADAS requires a deep understanding of drive environment and the interactions between the driving car and other road users in different situations. The results demonstrated the benefits of using naturalistic driving films as a mean for enhancing focus group discussion for better understanding driver's needs and traffic environment constraints. It provided an efficient tool for designers to have inside knowledge about drive and the needs for information presentation; The recommendations for how to apply this method is discussed in the paper.

DESIGN AND DEVELOPMENT REPORT ON TREAT CONTROL ROD DRIVE II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batch, R.V.

1961-05-01

A discussion is given of the development of TREAT control rod drive II, which describes the basic design, the problems involved with the design, the various design methods pursued, the testing procedures, and the evaluation of the performance characteristics of the final drive. (B.O.G.)

Analysis and topology optimization design of high-speed driving spindle

NASA Astrophysics Data System (ADS)

Wang, Zhilin; Yang, Hai

2018-04-01

The three-dimensional model of high-speed driving spindle is established by using SOLIDWORKS. The model is imported through the interface of ABAQUS, A finite element analysis model of high-speed driving spindle was established by using spring element to simulate bearing boundary condition. High-speed driving spindle for the static analysis, the spindle of the stress, strain and displacement nephogram, and on the basis of the results of the analysis on spindle for topology optimization, completed the lightweight design of high-speed driving spindle. The design scheme provides guidance for the design of axial parts of similar structures.

A design of driving circuit for star sensor imaging camera

NASA Astrophysics Data System (ADS)

Li, Da-wei; Yang, Xiao-xu; Han, Jun-feng; Liu, Zhao-hui

2016-01-01

The star sensor is a high-precision attitude sensitive measuring instruments, which determine spacecraft attitude by detecting different positions on the celestial sphere. Imaging camera is an important portion of star sensor. The purpose of this study is to design a driving circuit based on Kodak CCD sensor. The design of driving circuit based on Kodak KAI-04022 is discussed, and the timing of this CCD sensor is analyzed. By the driving circuit testing laboratory and imaging experiments, it is found that the driving circuits can meet the requirements of Kodak CCD sensor.

Parent use of touchscreen computer kiosks for child health promotion in community settings.

PubMed

Thompson, Darcy A; Lozano, Paula; Christakis, Dimitri A

2007-03-01

The goals were to evaluate the use of touchscreen computer kiosks, containing only child health-promoting information, in urban, low-income, community settings and to characterize the users of these kiosks. Three user-driven touchscreen computer kiosks were placed in low-income urban locations in Seattle, Washington, from March 2005 to October 2005. The locations included a public library, a Department of Motor Vehicles office, and a McDonald's restaurant. Users selected age-appropriate modules with prevention information and screening tools. Users entered the age of the child and were presented with age-appropriate modules. On exiting, users were asked to rate their experience and to provide basic demographic data. In total, there were 1846 kiosk sessions. Almost one half occurred at McDonald's. Seventy-eight percent of users identified themselves as first-time users. Users sought information for children of all ages. Sixty-one percent of first-time users explored 1 module. First-time users were most interested in television/media use (16%), smoke exposure (14%), attention-deficit/hyperactivity disorder screening (12%), and asthma assessment (11%). At-risk children were identified in 52% of sessions. Eighty-seven percent of first-time users who completed the asthma assessment had children whose asthma was uncontrolled. Twenty-eight percent of users responded to > or = 1 question on the exit survey. Of those, 48% had less than a high school education, and 26% had never used the Internet. Approximately one half found the kiosk easy to use (57%) and the information easy to understand (55%); 66% said there was at least some new information. Fifty-five percent planned to try some of the things they had learned, and 49% intended to talk to their child's doctor about what they had learned. User-driven computer kiosks were used in community settings to obtain child health information. Users found the kiosks easy to use. Additional study on improving use and understanding the impact is needed.

Modeling startup and shutdown transient of the microlinear piezo drive via ANSYS

NASA Astrophysics Data System (ADS)

Azin, A. V.; Bogdanov, E. P.; Rikkonen, S. V.; Ponomarev, S. V.; Khramtsov, A. M.

2017-02-01

The article describes the construction-design of the micro linear piezo drive intended for a peripheral cord tensioner in the reflecting surface shape regulator system for large-sized transformable spacecraft antenna reflectors. The research target -the development method of modeling startup and shutdown transient of the micro linear piezo drive. This method is based on application software package ANSYS. The method embraces a detailed description of the calculation stages to determine the operating characteristics of the designed piezo drive. Based on the numerical solutions, the time characteristics of the designed piezo drive are determined.

Variable-Reluctance Motor For Electric Vehicles

NASA Technical Reports Server (NTRS)

Lang, Jeffrey H.

1987-01-01

Report describes research on variable-reluctance electric-motor drive for eventual use in electric-vehicle propulsion. Primary design and performance criteria were torque and power output per unit mass of motor, cost, and drive efficiency. For each criterion, optimized drive design developed, and designs unified to yield single electric-vehicle drive. Scaled-down motor performed as expected. Prototype of paraplegic lift operated by toggle switch and joystick. Lift plugs into household electrical outlet for recharging when not in use.

Interactive instruction of cellular physiology for remote learning.

PubMed

Huang, C; Huang, H K

2003-12-01

The biomedical sciences are a rapidly changing discipline that have adapted to innovative technological advances. Despite these many advances, we face two major challenges: a) the number of experts in the field is vastly outnumbered by the number of students, many of whom are separated geographically or temporally and b) the teaching methods used to instruct students and learners have not changed. Today's students have adapted to technology--they use the web as a source of information and communicate via email and chat rooms. Teaching in the biomedical sciences should adopt these new information technologies (IT), but has thus far failed to capitalize on technological opportunity. Creating a "digital textbook" of the traditional learning material is not sufficient for dynamic processes such as cellular physiology. This paper describes innovative teaching techniques that incorporate familiar IT and high-quality interactive learning content with user-centric instruction design models. The Virtual Labs Project from Stanford University has created effective interactive online teaching modules in physiology (simPHYSIO) and delivered them over broadband networks to their undergraduate and medical students. Evaluation results of the modules are given as a measure of success of such innovative teaching method. This learning media strategically merges IT innovations with pedagogy to produce user-driven animations of processes and engaging interactive simulations.

Baseline practices and user needs for Web dissemination of geotechnical data

USGS Publications Warehouse

Turner, L.L.; Brown, M.P.; Chambers, D.; Davis, C.A.; Diehl, J.; Hitchcock, C.S.; Holzer, T.L.; Nigbor, R.L.; Plumb, C.; Real, C.; Reimer, M.; Steidl, J.H.; Sun, J.I.; Tinsley, J.C.; Vaughn, D.; ,

2004-01-01

This paper presents the findings and recommendations of the User Scenario Work Group (USWG) in identifying a baseline of current practices within the geo-professional community and prioritizing desired functional requirements in the development of a comprehensive geotechnical information management system. This work was conducted as an initial phase of a larger project to demonstrate the effectiveness of a web based virtual data center for the dissemination of geotechnical data from multiple linked databases of various government and private sector organizations. An online survey was administered over the course of several months to practitioners across the nation. The results from the survey were compiled and examined to provide direction to the other project teams in the development of user-driven prototype data system.

Preliminary Design of an Autonomous Amphibious System

DTIC Science & Technology

2016-09-01

changing vehicle dynamics will require innovative new autonomy algorithms. The developed software architecture, drive-by- wire kit, and supporting...COMMUNICATIONS ARCHITECTURE .................................................12 3.3 DRIVE-BY- WIRE DESIGN...SOFTWARE MATURATION PLANS ......................................................17 4.2 DRIVE-BY- WIRE PLANNED REFINEMENT

Identifying User Needs and the Participative Design Process

NASA Astrophysics Data System (ADS)

Meiland, Franka; Dröes, Rose-Marie; Sävenstedt, Stefan; Bergvall-Kåreborn, Birgitta; Andersson, Anna-Lena

As the number of persons with dementia increases and also the demands on care and support at home, additional solutions to support persons with dementia are needed. The COGKNOW project aims to develop an integrated, user-driven cognitive prosthetic device to help persons with dementia. The project focuses on support in the areas of memory, social contact, daily living activities and feelings of safety. The design process is user-participatory and consists of iterative cycles at three test sites across Europe. In the first cycle persons with dementia and their carers (n = 17) actively participated in the developmental process. Based on their priorities of needs and solutions, on their disabilities and after discussion between the team, a top four list of Information and Communication Technology (ICT) solutions was made and now serves as the basis for development: in the area of remembering - day and time orientation support, find mobile service and reminding service, in the area of social contact - telephone support by picture dialling, in the area of daily activities - media control support through a music playback and radio function, and finally, in the area of safety - a warning service to indicate when the front door is open and an emergency contact service to enhance feelings of safety. The results of this first project phase show that, in general, the people with mild dementia as well as their carers were able to express and prioritize their (unmet) needs, and the kind of technological assistance they preferred in the selected areas. In next phases it will be tested if the user-participatory design and multidisciplinary approach employed in the COGKNOW project result in a user-friendly, useful device that positively impacts the autonomy and quality of life of persons with dementia and their carers.

Long-Life, Lightweight, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration

NASA Technical Reports Server (NTRS)

Klein, Richard C.; Fusaro, Robert L.; Dimofte, Florin

2012-01-01

NASA s initiative for Lunar and Martian exploration will require long lived, robust drive systems for manned vehicles that must operate in hostile environments. The operation of these mechanical drives will pose a problem because of the existing extreme operating conditions. Some of these extreme conditions include operating at a very high or very cold temperature, operating over a wide range of temperatures, operating in very dusty environments, operating in a very high radiation environment, and operating in possibly corrosive environments. Current drive systems use gears with various configurations of teeth. These gears must be lubricated with oil (or grease) and must have some sort of a lubricant resupply system. For drive systems, oil poses problems such as evaporation, becoming too viscous and eventually freezing at cold temperatures, being too thin to lubricate at high temperatures, being degraded by the radiation environment, being contaminated by the regolith (soil), and if vaporized (and not sealed), it will contaminate the regolith. Thus, it may not be advisable or even possible to use oil because of these limitations. An oil-less, compact traction vehicle drive is a drive designed for use in hostile environments like those that will be encountered on planetary surfaces. Initially, traction roller tests in vacuum were conducted to obtain traction and endurance data needed for designing the drives. From that data, a traction drive was designed that would fit into a prototype lunar rover vehicle, and this design data was used to construct several traction drives. These drives were then tested in air to determine their performance characteristics, and if any final corrections to the designs were necessary. A limitation with current speed reducer systems such as planetary gears and harmonic drives is the high-contact stresses that occur at tooth engagement and in the harmonic drive wave generator interface. These high stresses induce high wear of solid lubricant coatings, thus necessitating the use of liquid lubricants for long life.

Mechanical design of walking machines.

PubMed

Arikawa, Keisuke; Hirose, Shigeo

2007-01-15

The performance of existing actuators, such as electric motors, is very limited, be it power-weight ratio or energy efficiency. In this paper, we discuss the method to design a practical walking machine under this severe constraint with focus on two concepts, the gravitationally decoupled actuation (GDA) and the coupled drive. The GDA decouples the driving system against the gravitational field to suppress generation of negative power and improve energy efficiency. On the other hand, the coupled drive couples the driving system to distribute the output power equally among actuators and maximize the utilization of installed actuator power. First, we depict the GDA and coupled drive in detail. Then, we present actual machines, TITAN-III and VIII, quadruped walking machines designed on the basis of the GDA, and NINJA-I and II, quadruped wall walking machines designed on the basis of the coupled drive. Finally, we discuss walking machines that travel on three-dimensional terrain (3D terrain), which includes the ground, walls and ceiling. Then, we demonstrate with computer simulation that we can selectively leverage GDA and coupled drive by walking posture control.

Roller-gear drives for robotic manipulators design, fabrication and test

NASA Technical Reports Server (NTRS)

Anderson, William J.; Shipitalo, William

1991-01-01

Two single axis planetary roller-gear drives and a two axis roller-gear drive with dual inputs were designed for use as robotic transmissions. Each of the single axis drives is a two planet row, four planet arrangement with spur gears and compressively loaded cylindrical rollers acting in parallel. The two axis drive employs bevel gears and cone rollers acting in parallel. The rollers serve a dual function: they remove backlash from the system, and they transmit torque when the gears are not fully engaged.

Naturalistic drive cycle synthesis for pickup trucks.

PubMed

Liu, Zifan; Ivanco, Andrej; Filipi, Zoran

2015-09-01

Future pick-up trucks are meeting much stricter fuel economy and exhaust emission standards. Design tradeoffs will have to be carefully evaluated to satisfy consumer expectations within the regulatory and cost constraints. Boundary conditions will obviously be critical for decision making: thus, the understanding of how customers are driving in naturalistic settings is indispensable. Federal driving schedules, while critical for certification, do not capture the richness of naturalistic cycles, particularly the aggressive maneuvers that often shape consumer perception of performance. While there are databases with large number of drive cycles, applying all of them directly in the design process is impractical. Therefore, representative drive cycles that capture the essence of the naturalistic driving should be synthesized from naturalistic driving data. Naturalistic drive cycles are firstly categorized by investigating their micro-trip components, defined as driving activities between successive stops. Micro-trips are expected to characterize underlying local traffic conditions, and separate different driving patterns. Next, the transitions from one vehicle state to another vehicle state in each cycle category are captured with Transition Probability Matrix (TPM). Candidate drive cycles can subsequently be synthesized using Markov Chain based on TPMs for each category. Finally, representative synthetic drive cycles are selected through assessment of significant cycle metrics to identify the ones with smallest errors. This paper provides a framework for synthesis of representative drive cycles from naturalistic driving data, which can subsequently be used for efficient optimization of design or control of pick-up truck powertrains. Manufacturers will benefit from representative drive cycles in several aspects, including quick assessments of vehicle performance and energy consumption in simulations, component sizing and design, optimization of control strategies, and vehicle testing under real-world conditions. This is in contrast to using federal certification test cycles, which were never intended to capture pickup truck segment. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

Double Sided-Design of Electrodes Driving Tunable Dielectrophoretic Miniature Lens.

PubMed

Almoallem, Yousuf; Jiang, Hongrui

2017-10-01

We demonstrate the design methodology, geometrical analysis, device fabrication, and testing of a double-sided design (DSD) of tunable-focus dielectrophoretic liquid miniature lenses. This design is intended to reduce the driving voltage for tuning the lens, utilizing a double-sided electrode design that enhances the electric field magnitude. Fabricated devices were tested and measurements on a goniometer showed changes of up to 14° in the contact angle when the dielectrophoretic force was applied under 25 V rms . Correspondingly, the back focal length of the liquid lens changed from 67.1 mm to 14.4 mm when the driving voltage was increased from zero to 25 V rms . The driving voltage was significantly lower than those previously reported with similar device dimensions using single-sided electrode designs. This design allows for a range of both positive and negative menisci dependent on the volume of the lens liquid initially dispensed.

An Optimization Framework for Driver Feedback Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malikopoulos, Andreas; Aguilar, Juan P.

2013-01-01

Modern vehicles have sophisticated electronic control units that can control engine operation with discretion to balance fuel economy, emissions, and power. These control units are designed for specific driving conditions (e.g., different speed profiles for highway and city driving). However, individual driving styles are different and rarely match the specific driving conditions for which the units were designed. In the research reported here, we investigate driving-style factors that have a major impact on fuel economy and construct an optimization framework to optimize individual driving styles with respect to these driving factors. In this context, we construct a set of polynomialmore » metamodels to reflect the responses produced in fuel economy by changing the driving factors. Then, we compare the optimized driving styles to the original driving styles and evaluate the effectiveness of the optimization framework. Finally, we use this proposed framework to develop a real-time feedback system, including visual instructions, to enable drivers to alter their driving styles in response to actual driving conditions to improve fuel efficiency.« less

14 CFR 29.917 - Design.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design. 29.917 Section 29.917 Aeronautics... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.917 Design. (a) General. The... part of, attached to, or mounted on the rotor drive system. (b) Design assessment. A design assessment...

14 CFR 29.917 - Design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design. 29.917 Section 29.917 Aeronautics... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.917 Design. (a) General. The... part of, attached to, or mounted on the rotor drive system. (b) Design assessment. A design assessment...

Drive-train dynamics technology - State-of-the-art and design of a test facility for advanced development

NASA Technical Reports Server (NTRS)

Badgley, R. H.; Fleming, D. P.; Smalley, A. J.

1975-01-01

A program for the development and verification of drive-train dynamic technology is described along with its basis and the results expected from it. A central feature of this program is a drive-train test facility designed for the testing and development of advanced drive-train components, including shaft systems, dampers, and couplings. Previous efforts in designing flexible dynamic drive-train systems are reviewed, and the present state of the art is briefly summarized. The design of the test facility is discussed with major attention given to the formulation of the test-rig concept, dynamic scaling of model shafts, and the specification of design parameters. Specific efforts envisioned for the test facility are briefly noted, including evaluations of supercritical test shafts, stability thresholds for various sources and types of instabilities that can exist in shaft systems, effects of structural flexibility on the dynamic performance of dampers, and methods for vibration control in two-level and three-level flexible shaft systems.

Multidisciplinary design optimization of the belt drive system considering both structure and vibration characteristics based on improved genetic algorithm

NASA Astrophysics Data System (ADS)

Yuan, Yongliang; Song, Xueguan; Sun, Wei; Wang, Xiaobang

2018-05-01

The dynamic performance of a belt drive system is composed of many factors, such as the efficiency, the vibration, and the optimal parameters. The conventional design only considers the basic performance of the belt drive system, while ignoring its overall performance. To address all these challenges, the study on vibration characteristics and optimization strategies could be a feasible way. This paper proposes a new optimization strategy and takes a belt drive design optimization as a case study based on the multidisciplinary design optimization (MDO). The MDO of the belt drive system is established and the corresponding sub-systems are analyzed. The multidisciplinary optimization is performed by using an improved genetic algorithm. Based on the optimal results obtained from the MDO, the three-dimension (3D) model of the belt drive system is established for dynamics simulation by virtual prototyping. From the comparison of the results with respect to different velocities and loads, the MDO method can effectively reduce the transverse vibration amplitude. The law of the vibration displacement, the vibration frequency, and the influence of velocities on the transverse vibrations has been obtained. Results show that the MDO method is of great help to obtain the optimal structural parameters. Furthermore, the kinematics principle of the belt drive has been obtained. The belt drive design case indicates that the proposed method in this paper can also be used to solve other engineering optimization problems efficiently.

High-power piezo drive amplifier for large stack and PFC applications

NASA Astrophysics Data System (ADS)

Clingman, Dan J.; Gamble, Mike

2001-08-01

This paper describes the continuing development of Boeing High Power Piezo Drive Amplifiers. Described is the development and testing of a 1500 Vpp, 8 amp switching amplifier. This amplifier is used to drive a piezo stack driven rotor blade trailing edge flap on a full size helicopter. Also discuss is a switching amplifier designed to drive a Piezo Fiber Composite (PFC) active twist rotor blade. This amplifier was designed to drive the PFC material at 2000 Vpp and 0.5 amps. These amplifiers recycle reactive energy, allowing for a power and weight efficient amplifier design. This work was done in conjunction with the DARPA sponsored Phase II Smart Rotor Blade program and the NASA Langley Research Center sponsored Active Twist Rotor (ATR) blade program.

Variation of Extreme and Fatigue Design Loads on the Main Bearing of a Front Mounted Direct Drive System

NASA Astrophysics Data System (ADS)

Abrahamsen, Asger Bech; Natarajan, Anand

2016-09-01

The drivetrain of a 10 MW wind turbine has been designed as a direct drive transmission with a superconducting generator mounted in front of the hub and connected to the main frame through a King-pin stiff assembly by DNV-GL. The aeroelastic design loads of such an arrangement are evaluated based on the thrust and bending moments at the main bearing, both for ultimate design and in fatigue. It is found that the initial superconductor generator weight of 363 tons must be reduced by 25% in order not to result in higher extreme loads on main and yaw bearing than the reference10 MW geared reference drive train. A weight reduction of 50% is needed in order to maintain main bearing fatigue damage equivalent to the reference drive train. Thus a target mass of front mounted superconducting direct drive generators is found to be between 183-272 tons.

Robust spherical direct-drive design for NI

NASA Astrophysics Data System (ADS)

Masse, Laurent; Hurricane, O.; Michel, P.; Nora, R.; Tabak, M.; Lawrence Livermore Natl Lab Team

2016-10-01

Achieving ignition in a direct-drive or indirect-drive cryogenic implosion is a tremendous challenge. Both approaches need to deal with physic and technologic issues. During the past years, the indirect drive effort on the National Ignition Facility (NIF) has revealed unpredicted lost of performances that force to think to more robust designs and to dig into detailed physics aspects. Encouraging results have been obtained using a strong first shock during the implosion of CH ablator ignition capsules. These ``high-foot'' implosion results in a significantly lower ablation Rayleigh-Taylor instability growth than that of the NIC point design capsule. The trade-off with this design is a higher fuel adiabat that limits both fuel compression and theoretical capsule yield. The purpose of designing this capsule is to recover a more ideal one-dimensional implosion that is in closer agreement to simulation predictions. In the same spirit of spending energy on margin, at the coast of decreased performance, we are presenting here a study on ``robust'' spherical direct drive design for NIF. This 2-Shock direct drive pulse shape results in a high adiabat (>3) and low convergence (<17) implosion designed to produce a near 1D-like implosion. We take a particular attention to design a robust implosion with respect to long-wavelength non uniformity seeded by power imbalance and target offset. This work was performed under the auspices of the Lawrence Livermore National Security, LLC, (LLNS) under Contract No. DE-AC52-07NA27344.

Handbook on Face Gear Drives with a Spur Involute Pinion

NASA Technical Reports Server (NTRS)

Litvin, F. L.; Egelja, A.; Tan, J.; Chen, D. Y.-D.; Heath, G.

2000-01-01

The use of face gears in power transmission and drive systems has a significant number of benefits. Face gears allow a variety of new transmission arrangements as well as high reduction ratio capability. This leads to drive system weight reduction and improvements in performance. In this work, basic information about the design and analysis of face gear drives is presented. The work considers face gears in mesh with spur involute pinions for both intersecting axes and offset drives. Tooth geometry, kinematics, generation of face gears with localized bearing contact by cutting and grinding, avoidance of tooth undercutting, avoidance of tooth pointing, tooth contact analysis, and algorithms for the simulation of meshing and contact arc all topics which are discussed. In addition, applications of face gear drives are presented. Included are design uses in aerospace applications such as helicopter transmissions, split-torque face gear arrangements, comparisons of face gears with bevel gears, and general design considerations.

User-driven integrated software lives: ``Paleomag'' paleomagnetics analysis on the Macintosh

NASA Astrophysics Data System (ADS)

Jones, Craig H.

2002-12-01

"PaleoMag," a paleomagnetics analysis package originally developed for the Macintosh operating system in 1988, allows examination of demagnetization of individual samples and analysis of directional data from collections of samples. Prior to recent reinvigorated development of the software for both Macintosh and Windows, it was widely used despite not running properly on machines and operating systems sold after 1995. This somewhat surprising situation demonstrates that there is a continued need for integrated analysis software within the earth sciences, in addition to well-developed scripting and batch-mode software. One distinct advantage of software like PaleoMag is in the ability to combine quality control with analysis within a unique graphical environment. Because such demands are frequent within the earth sciences, means of nurturing the development of similar software should be found.

14 CFR 29.917 - Design.

Code of Federal Regulations, 2012 CFR

2012-01-01

... conditions for which certification is sought. The design assessment must include a detailed failure analysis..., supporting bearings for shafting, any attendant accessory pads or drives, and any cooling fans that are a part of, attached to, or mounted on the rotor drive system. (b) Design assessment. A design assessment...

14 CFR 29.917 - Design.

Code of Federal Regulations, 2013 CFR

2013-01-01

... conditions for which certification is sought. The design assessment must include a detailed failure analysis..., supporting bearings for shafting, any attendant accessory pads or drives, and any cooling fans that are a part of, attached to, or mounted on the rotor drive system. (b) Design assessment. A design assessment...

14 CFR 29.917 - Design.

Code of Federal Regulations, 2014 CFR

2014-01-01

... conditions for which certification is sought. The design assessment must include a detailed failure analysis..., supporting bearings for shafting, any attendant accessory pads or drives, and any cooling fans that are a part of, attached to, or mounted on the rotor drive system. (b) Design assessment. A design assessment...

Determination of power and moment on shaft of special asynchronous electric drives

NASA Astrophysics Data System (ADS)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

In the article, questions and tasks of determination of power and the moment on a shaft of special asynchronous electric drives are considered. Use of special asynchronous electric drives in mechanical engineering and other industries is relevant. The considered types of electric drives possess the improved mass-dimensional indicators in comparison with singleengine systems. Also these types of electric drives have constructive advantages; the improved characteristics allow one to realize the technological process. But creation and design of new electric drives demands adjustment of existing or development of new methods and approaches of calculation of parameters. Determination of power and the moment on a shaft of special asynchronous electric drives is the main objective during design of electric drives. This task has been solved based on a method of electromechanical transformation of energy.

49 CFR 571.201 - Standard No. 201; Occupant protection in interior impact.

Code of Federal Regulations, 2011 CFR

2011-10-01

... seat. Ambulance means a motor vehicle designed exclusively for the purpose of emergency medical care... designated seating position, with adjustable forward seats in their rearmost design driving position and reclinable forward seat backs in their nominal design driving position; (b) Direction of impact shall be...

49 CFR 571.201 - Standard No. 201; Occupant protection in interior impact.

Code of Federal Regulations, 2010 CFR

2010-10-01

... seat. Ambulance means a motor vehicle designed exclusively for the purpose of emergency medical care... designated seating position, with adjustable forward seats in their rearmost design driving position and reclinable forward seat backs in their nominal design driving position; (b) Direction of impact shall be...

Design criteria monograph on centrifugal flow turbopumps

NASA Technical Reports Server (NTRS)

1974-01-01

Monograph reviews and assesses current design practices, and from them establishes firm guidance for achieving greater consistency in design, increased reliability in end product, and greater efficiency in design effort. Review should be of interest to manufacturers and users of pumps, power drives, turbine drives, and rotary equipment in general.

Modeling Interactions Between Flexible Flapping Wing Spars, Mechanisms, and Drive Motors

DTIC Science & Technology

2011-09-01

of dynamical equations is presented that allow micro air vehicle (MAV) or- nithopter designers to match drive motors to loads produced by flexible...aeroelastic systems is presented. One potential use for such a model is to serve as the basis for a vehicle design tool that matches drive motors to loads...friction. ∗Senior Aerospace Engineer, Control Design and Analysis Branch, 2210 Eighth Street, Ste. 21, Air Force Research Labora- tory, WPAFB, OH 45433

Design and simulation of MEMS-actuated adjustable optical wedge for laser beam scanners

NASA Astrophysics Data System (ADS)

Bahgat, Ahmed S.; Zaki, Ahmed H.; Abdo Mohamed, Mohamed; El Sherif, Ashraf Fathy

2018-01-01

This paper introduces both optical and mechanical design and simulation of large static deflection MOEMS actuator. The designed device is in the form of an adjustable optical wedge (AOW) laser scanner. The AOW is formed of 1.5-mm-diameter plano-convex lens separated by air gap from plano-concave fixed lens. The convex lens is actuated by staggered vertical comb drive and suspended by rectangular cross-section torsion beam. An optical analysis and simulation of air separated AOW as well as detailed design, analysis, and static simulation of comb -drive are introduced. The dynamic step response of the full system is also introduced. The analytical solution showed a good agreement with the simulation results. A general global minimum optimization algorithm is applied to the comb-drive design to minimize driving voltage. A maximum comb-drive mechanical deflection angle of 12 deg in each direction was obtained under DC actuation voltage of 32 V with a settling time of 90 ms, leading to 1-mm one-dimensional (1-D) steering of laser beam with continuous optical scan angle of 5 deg in each direction. This optimization process provided a design of larger deflection actuator with smaller driving voltage compared with other conventional devices. This enhancement could lead to better performance of MOEMS-based laser beam scanners for imaging and low-speed applications.

A 10kW series resonant converter design, transistor characterization, and base-drive optimization

NASA Technical Reports Server (NTRS)

Robson, R.; Hancock, D.

1981-01-01

Transistors are characterized for use as switches in resonant circuit applications. A base drive circuit to provide the optimal base drive to these transistors under resonant circuit conditions is developed and then used in the design, fabrication and testing of a breadboard, spaceborne type 10 kW series resonant converter.

Design and development of a solar array drive. [a direct drive solar array pointing mechanism

NASA Technical Reports Server (NTRS)

Rees, T.; Standing, J. M.

1977-01-01

The design and development of a dry lubricated direct drive solar array pointing mechanism is discussed for use on the Orbital Test Satellite (OTS), MAROTS, European Communication Satellite (ECS), and others. Results of life testing the original prototype and the OTS mechanism are presented together with an appraisal of expected future development.

Conceptual design of a connected vehicle wrong-way driving detection and management system.

DOT National Transportation Integrated Search

2016-04-01

This report describes the tasks completed to develop a concept of operations, functional requirements, and : high-level system design for a Connected Vehicle (CV) Wrong-Way Driving (WWD) Detection and Management : System. This system was designed to ...

14 CFR 27.917 - Design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design. 27.917 Section 27.917 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.917 Design. (a) Each rotor drive...

14 CFR 27.917 - Design.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design. 27.917 Section 27.917 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.917 Design. (a) Each rotor drive...

The role of personality traits and driving experience in self-reported risky driving behaviors and accident risk among Chinese drivers.

PubMed

Tao, Da; Zhang, Rui; Qu, Xingda

2017-02-01

The purpose of this study was to explore the role of personality traits and driving experience in the prediction of risky driving behaviors and accident risk among Chinese population. A convenience sample of drivers (n=511; mean (SD) age=34.2 (8.8) years) completed a self-report questionnaire that was designed based on validated scales for measuring personality traits, risky driving behaviors and self-reported accident risk. Results from structural equation modeling analysis demonstrated that the data fit well with our theoretical model. While showing no direct effects on accident risk, personality traits had direct effects on risky driving behaviors, and yielded indirect effects on accident risk mediated by risky driving behaviors. Both driving experience and risky driving behaviors directly predicted accident risk and accounted for 15% of its variance. There was little gender difference in personality traits, risky driving behaviors and accident risk. The findings emphasized the importance of personality traits and driving experience in the understanding of risky driving behaviors and accident risk among Chinese drivers and provided new insight into the design of evidence-based driving education and accident prevention interventions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design of a Novel Electro-hydraulic Drive Downhole Tractor

NASA Astrophysics Data System (ADS)

Fang, Delei; Shang, Jianzhong; Yang, Junhong; Wang, Zhuo; Wu, Wei

2018-02-01

In order to improve the traction ability and the work efficiency of downhole tractor in oil field, a novel electro-hydraulic drive downhole tractor was designed. The tractor’s supporting mechanism and moving mechanism were analyzed based on the tractor mechanical structure. Through the introduction of hydraulic system, the hydraulic drive mechanism and the implementation process were researched. Based on software, analysis of tractor hydraulic drive characteristic and movement performance were simulated, which provide theoretical basis for the development of tractor prototype.

Actuators for a space manipulator

NASA Technical Reports Server (NTRS)

Chun, W.; Brunson, P.

1987-01-01

The robotic manipulator can be decomposed into distinct subsytems. One particular area of interest of mechanical subsystems is electromechanical actuators (or drives). A drive is defined as a motor with an appropriate transmission. An overview is given of existing, as well as state-of-the-art drive systems. The scope is limited to space applications. A design philosophy and adequate requirements are the initial steps in designing a space-qualified actuator. The focus is on the d-c motor in conjunction with several types of transmissions (harmonic, tendon, traction, and gear systems). The various transmissions will be evaluated and key performance parameters will be addressed in detail. Included in the assessment is a shuttle RMS joint and a MSFC drive of the Prototype Manipulator Arm. Compound joints are also investigated. Space imposes a set of requirements for designing a high-performance drive assembly. Its inaccessibility and cryogenic conditions warrant special considerations. Some guidelines concerning these conditions are present. The goal is to gain a better understanding in designing a space actuator.

Design and experimental study of a novel giant magnetostrictive actuator

NASA Astrophysics Data System (ADS)

Xue, Guangming; Zhang, Peilin; He, Zhongbo; Li, Dongwei; Huang, Yingjie; Xie, Wenqiang

2016-12-01

Giant magnetostrictive actuator has been widely used in precise driving occasions for its excellent performance. However, in driving a switching valve, especially the ball-valve in an electronic controlled injector, the actuator can't exhibit its good performance for limits in output displacement and responding speed. A novel giant magnetostrictive actuator, which can reach its maximum displacement for being exerted with no bias magnetic field, is designed in this paper. Simultaneously, elongating of the giant magetostrictive material is converted to shortening of the actuator's axial dimension with the help of an output rod in "T" type. Furthermore, to save responding time, the driving voltage with high opening voltage while low holding voltage is designed. Responding time and output displacement are studied experimentally with the help of a measuring system. From measured results, designed driving voltage can improve the responding speed of actuator displacement quite effectively. And, giant magnetostrictive actuator can output various steady-state displacements to reach more driving effects.

The Future of Geospatial Standards

NASA Astrophysics Data System (ADS)

Bermudez, L. E.; Simonis, I.

2016-12-01

The OGC is an international not-for-profit standards development organization (SDO) committed to making quality standards for the geospatial community. A community of more than 500 member organizations with more than 6,000 people registered at the OGC communication platform drives the development of standards that are freely available for anyone to use and to improve sharing of the world's geospatial data. OGC standards are applied in a variety of application domains including Environment, Defense and Intelligence, Smart Cities, Aviation, Disaster Management, Agriculture, Business Development and Decision Support, and Meteorology. Profiles help to apply information models to different communities, thus adapting to particular needs of that community while ensuring interoperability by using common base models and appropriate support services. Other standards address orthogonal aspects such as handling of Big Data, Crowd-sourced information, Geosemantics, or container for offline data usage. Like most SDOs, the OGC develops and maintains standards through a formal consensus process under the OGC Standards Program (OGC-SP) wherein requirements and use cases are discussed in forums generally open to the public (Domain Working Groups, or DWGs), and Standards Working Groups (SWGs) are established to create standards. However, OGC is unique among SDOs in that it also operates the OGC Interoperability Program (OGC-IP) to provide real-world testing of existing and proposed standards. The OGC-IP is considered the experimental playground, where new technologies are researched and developed in a user-driven process. Its goal is to prototype, test, demonstrate, and promote OGC Standards in a structured environment. Results from the OGC-IP often become requirements for new OGC standards or identify deficiencies in existing OGC standards that can be addressed. This presentation will provide an analysis of the work advanced in the OGC consortium including standards and testbeds, where we can extract a trend for the future of geospatial standards. We see a number of key elements in focus, but simultaneously a broadening of standards to address particular communities' needs.

Voltage Drop Compensation Method for Active Matrix Organic Light Emitting Diode Displays

NASA Astrophysics Data System (ADS)

Choi, Sang-moo; Ryu, Do-hyung; Kim, Keum-nam; Choi, Jae-beom; Kim, Byung-hee; Berkeley, Brian

2011-03-01

In this paper, the conventional voltage drop compensation methods are reviewed and the novel design and driving scheme, the advanced power de-coupled (aPDC) driving method, is proposed to effectively compensate the voltage IR drop of active matrix light emitting diode (AMOLED) displays. The advanced PDC driving scheme can be applied to general AMOLED pixel circuits that have been developed with only minor modification or without requiring modification in pixel circuit. A 14-in. AMOLED panel with the aPDC driving scheme was fabricated. Long range uniformity (LRU) of the 14-in. AMOLED panel was improved from 43% without the aPDC driving scheme, to over 87% at the same brightness by using the scheme and the layout complexity of the panel with new design scheme is less than that of the panel with the conventional design scheme.

Design of a 7kW power transfer solar array drive mechanism

NASA Technical Reports Server (NTRS)

Sheppard, J. G.

1982-01-01

With the availability of the Shuttle and the European launcher, Ariane, there will be a continuing trend towards large payload satellite missions requiring high-power, high-inertia, flexible solar arrays. The need arises for a solar array drive with a large power transfer capability which can rotate these solar arrays without disturbing the satellite body pointing. The modular design of such a Solar Array Drive Mechanism (SADM) which is capable of transferring 7kW of power or more is described. Total design flexibility has been achieved, enabling different spacecraft power requirements to be accommodated within the SADM design.

Gear Design Effects on the Performance of High Speed Helical Gear Trains as Used in Aerospace Drive Systems

NASA Technical Reports Server (NTRS)

Handschuh, R.; Kilmain, D.; Ehinger, R.; Sinusas, E.

2013-01-01

The performance of high-speed helical gear trains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction/torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High Speed Helical Gear Train Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160 to 250 F) and lubricating jet pressure (60 to 80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears. The empirical data resulting from this study will be useful to the design of future helical gear train systems anticipated for next generation rotorcraft drive systems.

Gear Design Effects on the Performance of High Speed Helical Gear Trains as Used in Aerospace Drive Systems

NASA Technical Reports Server (NTRS)

Handschuh, R.; Kilmain, C.; Ehinger, R.; Sinusas, E.

2013-01-01

The performance of high-speed helical gear trains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction / torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High Speed Helical Gear Train Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160 to 250 degF) and lubricating jet pressure (60 to 80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears. The empirical data resulting from this study will be useful to the design of future helical gear train systems anticipated for next generation rotorcraft drive systems.

Friends Don't Let Friends Drive Drunk, But Do They Let Friends Drive High?

ERIC Educational Resources Information Center

Glascoff, Mary A.; Shrader, Joe S.; Haddock, Rose K.

2013-01-01

This study reports on a study of college students at a state supported university regarding the use of designated drivers associated with illicit drug use, especially marijuana use. The purpose of the study was to examine whether college students report that they drive under the influence of illicit drugs, if they use the strategy of designating a…

Design of driving control strategy of torque distribution for two - wheel independent drive electric vehicle

NASA Astrophysics Data System (ADS)

Zhang, Chuanwei; Zhang, Dongsheng; Wen, Jianping

2018-02-01

In order to coordinately control the torque distribution of existing two-wheel independent drive electric vehicle, and improve the energy efficiency and control stability of the whole vehicle, the control strategies based on fuzzy control were designed which adopt the direct yaw moment control as the main line. For realizing the torque coordination simulation of the two-wheel independent drive vehicle, the vehicle model, motor model and tire model were built, including the vehicle 7 - DOF dynamics model, motion equation, torque equation. Finally, in the Carsim - Simulink joint simulation platform, the feasibility of the drive control strategy was verified.

Optimal design of a main driving mechanism for servo punch press based on performance atlases

NASA Astrophysics Data System (ADS)

Zhou, Yanhua; Xie, Fugui; Liu, Xinjun

2013-09-01

The servomotor drive turret punch press is attracting more attentions and being developed more intensively due to the advantages of high speed, high accuracy, high flexibility, high productivity, low noise, cleaning and energy saving. To effectively improve the performance and lower the cost, it is necessary to develop new mechanisms and establish corresponding optimal design method with uniform performance indices. A new patented main driving mechanism and a new optimal design method are proposed. In the optimal design, the performance indices, i.e., the local motion/force transmission indices ITI, OTI, good transmission workspace good transmission workspace(GTW) and the global transmission indices GTIs are defined. The non-dimensional normalization method is used to get all feasible solutions in dimensional synthesis. Thereafter, the performance atlases, which can present all possible design solutions, are depicted. As a result, the feasible solution of the mechanism with good motion/force transmission performance is obtained. And the solution can be flexibly adjusted by designer according to the practical design requirements. The proposed mechanism is original, and the presented design method provides a feasible solution to the optimal design of the main driving mechanism for servo punch press.

Effects on driving performance of interacting with an in-vehicle music player: a comparison of three interface layout concepts for information presentation.

PubMed

Mitsopoulos-Rubens, Eve; Trotter, Margaret J; Lenné, Michael G

2011-05-01

Interface design is an important factor in assessing the potential effects on safety of interacting with an in-vehicle information system while driving. In the current study, the layout of information on a visual display was manipulated to explore its effect on driving performance in the context of music selection. The comparative effects of an auditory-verbal (cognitive) task were also explored. The driving performance of 30 participants was assessed under both baseline and dual task conditions using the Lane Change Test. Concurrent completion of the music selection task with driving resulted in significant impairment to lateral driving performance (mean lane deviation and percentage of correct lane changes) relative to the baseline, and significantly greater mean lane deviation relative to the combined driving and the cognitive task condition. The magnitude of these effects on driving performance was independent of layout concept, although significant differences in subjective workload estimates and performance on the music selection task across layout concepts highlights that potential uncertainty regarding design use as conveyed through layout concept could be disadvantageous. The implications of these results for interface design and safety are discussed. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Value Co-creation and Co-innovation: Linking Networked Organisations and Customer Communities

NASA Astrophysics Data System (ADS)

Romero, David; Molina, Arturo

Strategic networks such as Collaborative Networked Organisations (CNOs) and Virtual Customer Communities (VCCs) show a high potential as drivers of value co-creation and collaborative innovation in today’s Networking Era. Both look at the network structures as a source of jointly value creation and open innovation through access to new skills, knowledge, markets and technologies by sharing risk and integrating complementary competencies. This collaborative endeavour has proven to be able to enhance the adaptability and flexibility of CNOs and VCCs value creating systems in order to react in response to external drivers such as collaborative (business) opportunities. This paper presents a reference framework for creating interface networks, also known as ‘experience-centric networks’, as enablers for linking networked organisations and customer communities in order to support the establishment of user-driven and collaborative innovation networks.

DSCOVR Science Data and Retrospective Access

NASA Astrophysics Data System (ADS)

Rowland, W. F.; Codrescu, S.; Tilton, M.; Cartwright, J.; Redmon, R. J.; Loto'aniu, P. T. M.; Mccullough, H.; Denig, W. F.

2016-12-01

On July 27, 2016 the Deep Space Climate Observatory (DSCOVR) became the first operational satellite at the first Lagrange point (L1). This vantage, approximately one percent of the distance from the Earth to the Sun along the Earth-Sun line, means that DSCOVR data provide critical advanced warning of impending space weather events. As such, DSCOVR data are essential for forecasters, modelers, and the scientific community. The National Oceanic and Atmospheric Administration's National Centers for Environmental Information (NOAA/NCEI) archives the retrospective data and shares them with the public. We examine the data available, with a focus on some of the more interesting events that have occurred. We also discuss mechanisms created to facilitate search and access for those data, including a user-driven interface that allows one to dynamically generate plots and order relevant data of interest.

Driving difficulties in Parkinson's disease

PubMed Central

Rizzo, Matthew; Uc, Ergun Y; Dawson, Jeffrey; Anderson, Steven; Rodnitzky, Robert

2011-01-01

Safe driving requires the coordination of attention, perception, memory, motor and executive functions (including decision-making) and self-awareness. PD and other disorders may impair these abilities. Because age or medical diagnosis alone is often an unreliable criterion for licensure, decisions on fitness to drive should be based on empirical observations of performance. Linkages between cognitive abilities measured by neuropsychological tasks, and driving behavior assessed using driving simulators, and natural and naturalistic observations in instrumented vehicles, can help standardize the assessment of fitness-to-drive. By understanding the patterns of driver safety errors that cause crashes, it may be possible to design interventions to reduce these errors and injuries and increase mobility. This includes driver performance monitoring devices, collision alerting and warning systems, road design, and graded licensure strategies. PMID:20187237

Quiet Clean Short-haul Experimental Engine (QCSEE): Hamilton Standard cam/harmonic drive variable pitch fan actuation system detail design report

NASA Technical Reports Server (NTRS)

1976-01-01

A variable pitch fan actuation system was designed which incorporates a remote nacelle-mounted blade angle regulator. The regulator drives a rotating fan-mounted mechanical actuator through a flexible shaft and differential gear train. The actuator incorporates a high ratio harmonic drive attached to a multitrack spherical cam which changes blade pitch through individual cam follower arms attached to each blade trunnion. Detail design parameters of the actuation system are presented. These include the following: design philosophies, operating limits, mechanical, hydraulic and thermal characteristics, mechanical efficiencies, materials, weights, lubrication, stress analyses, reliability and failure analyses.

Warning system against locomotive driving wheel flaccidity

NASA Astrophysics Data System (ADS)

Luo, Peng

2014-09-01

Causes of locomotive relaxation are discussed. Alarm system against locomotive driving wheel flaccidity is designed by means of techniques of infrared temperature measurement and Hall sensor measurement. The design scheme of the system, the principle of detecting locomotive driving wheel flaccidity with temperature and Hall sensor is introduced, threshold temperature of infrared alarm is determined. The circuit system is designed by microcontroller technology and the software is designed with the assembly language. The experiment of measuring the flaccid displacement with Hall sensor measurement is simulated. The results show that the system runs well with high reliability and low cost, which has a wide prospect of application and popularization.

The Visual Representation and Acquisition of Driving Knowledge for Autonomous Vehicle

NASA Astrophysics Data System (ADS)

Zhang, Zhaoxia; Jiang, Qing; Li, Ping; Song, LiangTu; Wang, Rujing; Yu, Biao; Mei, Tao

2017-09-01

In this paper, the driving knowledge base of autonomous vehicle is designed. Based on the driving knowledge modeling system, the driving knowledge of autonomous vehicle is visually acquired, managed, stored, and maintenanced, which has vital significance for creating the development platform of intelligent decision-making systems of automatic driving expert systems for autonomous vehicle.

The anti-fatigue driving system design based on the eye blink detect

NASA Astrophysics Data System (ADS)

Yang, Shuyu; Song, Xin; Zhang, Li; Yu, Jie

2017-01-01

Traffic accident is one of the severe social problems in the world, but the appraisal and prevention of the fatigue driving is still a difficult problem that can not be solved. This paper is to study the results of fatigue driving and the existing antifatigue driving products, collecting brain wave with the TGAM (ThinkGear AM) Brain Wave Sensor Chip. We analyze the collected waveform based on eye blink detect algorithm to work out current situation of the driver. According to the analysis results, Sound Module and controllable speed car will make a series of feedback. Finally, an effective Anti- Fatigue Driving System is designed based on all above.

Design of a portable artificial heart drive system based on efficiency analysis.

PubMed

Kitamura, T

1986-11-01

This paper discusses a computer simulation of a pneumatic portable piston-type artificial heart drive system with a linear d-c-motor. The purpose of the design is to obtain an artificial heart drive system with high efficiency and small dimensions to enhance portability. The design employs two factors contributing the total efficiency of the drive system. First, the dimensions of the pneumatic actuator were optimized under a cost function of the total efficiency. Second, the motor performance was studied in terms of efficiency. More than 50 percent of the input energy of the actuator with practical loads is consumed in the armature circuit in all linear d-c-motors with brushes. An optimal design is: the piston cross-sectional area of 10.5 cm2 cylinder longitudinal length of 10 cm. The total efficiency could be up to 25 percent by improving the gasket to reduce the frictional force.

49 CFR 571.201 - Standard No. 201; Occupant protection in interior impact.

Code of Federal Regulations, 2013 CFR

2013-10-01

... seat. Ambulance means a motor vehicle designed exclusively for the purpose of emergency medical care... seats in their rearmost design driving position and reclinable forward seat backs in their nominal design driving position; (b) Direction of impact shall be either: (1) In a vertical plane parallel to the...

49 CFR 571.201 - Standard No. 201; Occupant protection in interior impact.

Code of Federal Regulations, 2014 CFR

2014-10-01

... seat. Ambulance means a motor vehicle designed exclusively for the purpose of emergency medical care... seats in their rearmost design driving position and reclinable forward seat backs in their nominal design driving position; (b) Direction of impact shall be either: (1) In a vertical plane parallel to the...

49 CFR 571.201 - Standard No. 201; Occupant protection in interior impact.

Code of Federal Regulations, 2012 CFR

2012-10-01

... seat. Ambulance means a motor vehicle designed exclusively for the purpose of emergency medical care... seats in their rearmost design driving position and reclinable forward seat backs in their nominal design driving position; (b) Direction of impact shall be either: (1) In a vertical plane parallel to the...

High-Performance Cryogenic Designs for OMEGA and the National Ignition Facility

NASA Astrophysics Data System (ADS)

Goncharov, V. N.; Collins, T. J. B.; Marozas, J. A.; Regan, S. P.; Betti, R.; Boehly, T. R.; Campbell, E. M.; Froula, D. H.; Igumenshchev, I. V.; McCrory, R. L.; Myatt, J. F.; Radha, P. B.; Sangster, T. C.; Shvydky, A.

2016-10-01

The main advantage of laser symmetric direct drive (SDD) is a significantly higher coupled drive laser energy to the hot-spot internal energy at stagnation compared to that of laser indirect drive. Because of coupling losses resulting from cross-beam energy transfer (CBET), however, reaching ignition conditions on the NIF with SDD requires designs with excessively large in-flight aspect ratios ( 30). Results of cryogenic implosions performed on OMEGA show that such designs are unstable to short-scale nonuniformity growth during shell implosion. Several CBET reduction strategies have been proposed in the past. This talk will discuss high-performing designs using several CBET-mitigation techniques, including using drive laser beams smaller than the target size and wavelength detuning. Designs that are predicted to reach alpha burning regimes as well as a gain of 10 to 40 at the NIF-scale will be presented. Hydrodynamically scaled OMEGA designs with similar CBET-reduction techniques will also be discussed. This material is based upon work supported by the Department Of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Preface to the special section on human factors and automation in vehicles: designing highly automated vehicles with the driver in mind.

PubMed

Merat, Natasha; Lee, John D

2012-10-01

This special section brings together diverse research regarding driver interaction with advanced automotive technology to guide design of increasingly automated vehicles. Rapidly evolving vehicle automation will likely change cars and trucks more in the next 5 years than the preceding 50, radically redefining what it means to drive. This special section includes 10 articles from European and North American researchers reporting simulator and naturalistic driving studies. Little research has considered the consequences of fully automated driving, with most focusing on lane-keeping and speed control systems individually. The studies reveal two underlying design philosophies: automate driving versus support driving. Results of several studies, consistent with previous research in other domains, suggest that the automate philosophy can delay driver responses to incidents in which the driver has to intervene and take control from the automation. Understanding how to orchestrate the transfer or sharing of control between the system and the driver, particularly in critical incidents, emerges as a central challenge. Designers should not assume that automation can substitute seamlessly for a human driver, nor can they assume that the driver can safely accommodate the limitations of automation. Designers, policy makers, and researchers must give careful consideration to what role the person should have in highly automated vehicles and how to support the driver if the driver is to be responsible for vehicle control. As in other domains, driving safety increasingly depends on the combined performance of the human and automation, and successful designs will depend on recognizing and supporting the new roles of the driver.

Power Supply Fault Tolerant Reliability Study

DTIC Science & Technology

1991-04-01

easier to design than for equivalent bipolar transistors. MCDONNELL DOUGLAS ELECTRONICS SYSTEMS COMPANY 9. Base circuitry should be designed to drive...SWITCHING REGULATORS (Ref. 28), SWITCHING AND LINEAR POWER SUPPLY DESIGN (Ref. 25) 6. Sequence the turn-off/turn-on logic in an orderly and controllable ...for equivalent bipolar transistors. MCDONNELL DOUGLAS ELECTRONICS SYSTEMS COMPANY 8. Base circuitry should be designed to drive the transistor into

System design of a remotely operated, program controlled measurement table for the calibration of the Egret experiment. Part A: Program control

NASA Technical Reports Server (NTRS)

1984-01-01

The structure of the program, the five priority levels, the drive routines, the stepwise drive plan, the figure routines, meander X and y, the range of measurement table, the optimization of figure drive, the figure drive plan, dialogue routines, stack processing, the drive for the main terminal, the protocol routines, the drive for the microterminal, the drive for the experiment computer, and the main program are discussed.

Second generation registry framework.

PubMed

Bellgard, Matthew I; Render, Lee; Radochonski, Maciej; Hunter, Adam

2014-01-01

Information management systems are essential to capture data be it for public health and human disease, sustainable agriculture, or plant and animal biosecurity. In public health, the term patient registry is often used to describe information management systems that are used to record and track phenotypic data of patients. Appropriate design, implementation and deployment of patient registries enables rapid decision making and ongoing data mining ultimately leading to improved patient outcomes. A major bottleneck encountered is the static nature of these registries. That is, software developers are required to work with stakeholders to determine requirements, design the system, implement the required data fields and functionality for each patient registry. Additionally, software developer time is required for ongoing maintenance and customisation. It is desirable to deploy a sophisticated registry framework that can allow scientists and registry curators possessing standard computing skills to dynamically construct a complete patient registry from scratch and customise it for their specific needs with little or no need to engage a software developer at any stage. This paper introduces our second generation open source registry framework which builds on our previous rare disease registry framework (RDRF). This second generation RDRF is a new approach as it empowers registry administrators to construct one or more patient registries without software developer effort. New data elements for a diverse range of phenotypic and genotypic measurements can be defined at any time. Defined data elements can then be utilised in any of the created registries. Fine grained, multi-level user and workgroup access can be applied to each data element to ensure appropriate access and data privacy. We introduce the concept of derived data elements to assist the data element standards communities on how they might be best categorised. We introduce the second generation RDRF that enables the user-driven dynamic creation of patient registries. We believe this second generation RDRF is a novel approach to patient registry design, implementation and deployment and a significant advance on existing registry systems.

Second generation registry framework

PubMed Central

2014-01-01

Background Information management systems are essential to capture data be it for public health and human disease, sustainable agriculture, or plant and animal biosecurity. In public health, the term patient registry is often used to describe information management systems that are used to record and track phenotypic data of patients. Appropriate design, implementation and deployment of patient registries enables rapid decision making and ongoing data mining ultimately leading to improved patient outcomes. A major bottleneck encountered is the static nature of these registries. That is, software developers are required to work with stakeholders to determine requirements, design the system, implement the required data fields and functionality for each patient registry. Additionally, software developer time is required for ongoing maintenance and customisation. It is desirable to deploy a sophisticated registry framework that can allow scientists and registry curators possessing standard computing skills to dynamically construct a complete patient registry from scratch and customise it for their specific needs with little or no need to engage a software developer at any stage. Results This paper introduces our second generation open source registry framework which builds on our previous rare disease registry framework (RDRF). This second generation RDRF is a new approach as it empowers registry administrators to construct one or more patient registries without software developer effort. New data elements for a diverse range of phenotypic and genotypic measurements can be defined at any time. Defined data elements can then be utilised in any of the created registries. Fine grained, multi-level user and workgroup access can be applied to each data element to ensure appropriate access and data privacy. We introduce the concept of derived data elements to assist the data element standards communities on how they might be best categorised. Conclusions We introduce the second generation RDRF that enables the user-driven dynamic creation of patient registries. We believe this second generation RDRF is a novel approach to patient registry design, implementation and deployment and a significant advance on existing registry systems. PMID:24982690

Magnetostrictive direct drive motors

NASA Technical Reports Server (NTRS)

Naik, Dipak; Dehoff, P. H.

1990-01-01

Developing magnetostrictive direct drive research motors to power robot joints is discussed. These type motors are expected to produce extraordinary torque density, to be able to perform microradian incremental steps and to be self-braking and safe with the power off. Several types of motor designs have been attempted using magnetostrictive materials. One of the candidate approaches (the magnetostrictive roller drive) is described. The method in which the design will function is described as is the reason why this approach is inherently superior to the other approaches. Following this, the design will be modelled and its expected performance predicted. This particular candidate design is currently undergoing detailed engineering with prototype construction and testing scheduled for mid 1991.

CD-ROM Hardware Configurations: Selection and Design.

ERIC Educational Resources Information Center

Jaffe, Lee David; Watkins, Steven G.

1992-01-01

Presents selection and design considerations to help libraries make informed decisions about hardware configurations of CD-ROM systems. Highlights include CD-ROM configurations, including single drive workstations, daisychains, and jukeboxes; network configurations, including remote access; microcomputer features; CD-ROM drive selection; and…

Energy efficient engine. Core engine bearings, drives and configuration: Detailed design report

NASA Technical Reports Server (NTRS)

Broman, C. L.

1981-01-01

The detailed design of the forward and aft sumps, the accessory drive system, the lubrication system, and the piping/manifold configuration to be employed in the core engine test of the Energy Efficient Engine is addressed. The design goals for the above components were established based on the requirements of the test cell engine.

A programmable CCD driver circuit for multiphase CCD operation

NASA Technical Reports Server (NTRS)

Ewin, Audrey J.; Reed, Kenneth V.

1989-01-01

A programmable CCD (charge-coupled device) driver circuit was designed to drive CCDs in multiphased modes. The purpose of the drive electronics is to operate developmental CCD imaging arrays for NASA's tiltable moderate resolution imaging spectrometer (MODIS-T). Five objectives for the driver were considered during its design: (1) the circuit drives CCD electrode voltages between 0 V and +30 V to produce reasonable potential wells, (2) the driving sequence is started with one input signal, (3) the driving sequence is started with one input signal, (4) the circuit allows programming of frame sequences required by arrays of any size, (5) it produces interfacing signals for the CCD and the DTF (detector test facility). Simulation of the driver verified its function with the master clock running up to 10 MHz. This suggests a maximum rate of 400,000 pixels/s. Timing and packaging parameters were verified. The design uses 54 TTL (transistor-transistor logic) chips. Two versions of hardware were fabricated: wirewrap and printed circuit board. Both were verified functionally with a logic analyzer.

A polar-drive-ignition design for the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, T. J. B.; Marozas, J. A.; Anderson, K. S.

2012-05-15

Polar drive [Skupsky et al., Phys. Plasmas 11, 2763 (2004)] will enable direct-drive experiments to be conducted on the National Ignition Facility (NIF) [Miller et al., Opt. Eng. 43, 2841 (2004)], while the facility is configured for x-ray drive. A polar-drive ignition design for the NIF has been developed that achieves a gain of 32 in two-dimensional (2-D) simulations, which include single- and multiple-beam nonuniformities and ice and outer-surface roughness. This design requires both single-beam UV polarization smoothing and one-dimensional (1-D) multi-frequency modulator (MFM) single-beam smoothing to achieve the required laser uniformity. The multi-FM smoothing is employed only during themore » low-intensity portion of the laser pulse, allowing for the use of sufficient smoothing-by-spectral-dispersion bandwidth while maintaining safe laser operations during the high-intensity part of the pulse. This target is robust to all expected sources of perturbations.« less

Critical review and analysis of the impact of the physical infrastructure on the driving ability, performance, and safety of older adults.

PubMed

Bohr, Paula Christine

2008-01-01

Literature on the impact of physical infrastructure on older adult safe driving performance was reviewed in 2005 as part of the American Occupational Therapy Association's Evidence-Based Literature Review Project. Existing guidelines for driving environments, related to changes in visual, cognitive, and psychomotor abilities associated with the aging process (as published in the Highway Design Handbook for Older Drivers and Pedestrians, Federal Highway Administration, 2001), are exhaustive, but the authors made no attempt to critically assess the strength of the study design or level of evidence. In laboratory studies since 1999, the interventions lacked applicability to real-life driving environments. Further investigation of the effectiveness of best practice interventions and how the driving environment can better accommodate the needs of older drivers is needed. Occupational therapy interventions that focus on the occupation of driving and compensation and education strategies that allow older adults to drive safely as long as possible are included.

Friction self-oscillation decrease in nonlinear system of locomotive traction drive

NASA Astrophysics Data System (ADS)

Antipin, D. Ya; Vorobiyov, V. I.; Izmerov, O. V.; Shorokhov, S. G.; Bondarenko, D. A.

2017-02-01

The problems of the friction self-oscillation decrease in a nonlinear system of a locomotive traction drive are considered. It is determined that the self-oscillation amplitude decrease in a locomotive wheel pair during boxing in traction drives with an elastic linkage between an armature of a traction electric motor and gearing can be achieved due to drive damping capacity during impact vibro-damping in an axle reduction gear with a hard driven gear. The self-oscillation amplitude reduction in a wheel pair in the designs of locomotive traction drives with the location of elastic elements between a wheel pair and gearing can be obtained owing to the application of drive inertial masses as an anti-vibrator. On the basis of the carried out investigations, a design variant of a self-oscillation shock absorber of a traction electric motor framework on a reduction gear suspension with an absorber located beyond a wheel-motor unit was offered.

Rugby-like hohlraum experimental designs for demonstrating x-ray drive enhancement

NASA Astrophysics Data System (ADS)

Amendt, Peter; Cerjan, C.; Hinkel, D. E.; Milovich, J. L.; Park, H.-S.; Robey, H. F.

2008-01-01

A suite of experimental designs for the Omega laser facility [Boehly et al., Opt. Commun. 133, 495 (1997)] using rugby and cylindrical hohlraums is proposed to confirm the energetics benefits of rugby-shaped hohlraums over cylinders under optimal implosion symmetry conditions. Postprocessed Dante x-ray drive measurements predict a 12-17eV (23%-36%) peak hohlraum temperature (x-ray flux) enhancement for a 1ns flattop laser drive history. Simulated core self-emission x-ray histories also show earlier implosion times by 200-400ps, depending on the hohlraum case-to-capsule ratio and laser-entrance-hole size. Capsules filled with 10 or 50atm of deuterium (DD) are predicted to give in excess of 1010 neutrons in two-dimensional hohlraum simulations in the absence of mix, enabling DD burn history measurements for the first time in indirect-drive on Omega. Capsule designs with 50atm of DHe3 are also proposed to make use of proton slowing for independently verifying the drive benefits of rugby hohlraums. Scale-5/4 hohlraum designs are also introduced to provide further margin to potential laser-plasma-induced backscatter and hot-electron production.

Analog-to-digital clinical data collection on networked workstations with graphic user interface.

PubMed

Lunt, D

1991-02-01

An innovative respiratory examination system has been developed that combines physiological response measurement, real-time graphic displays, user-driven operating sequences, and networked file archiving and review into a scientific research and clinical diagnosis tool. This newly constructed computer network is being used to enhance the research center's ability to perform patient pulmonary function examinations. Respiratory data are simultaneously acquired and graphically presented during patient breathing maneuvers and rapidly transformed into graphic and numeric reports, suitable for statistical analysis or database access. The environment consists of the hardware (Macintosh computer, MacADIOS converters, analog amplifiers), the software (HyperCard v2.0, HyperTalk, XCMDs), and the network (AppleTalk, fileservers, printers) as building blocks for data acquisition, analysis, editing, and storage. System operation modules include: Calibration, Examination, Reports, On-line Help Library, Graphic/Data Editing, and Network Storage.

Evaluation of half wave induction motor drive for use in passenger vehicles

NASA Technical Reports Server (NTRS)

Hoft, R. G.; Kawamura, A.; Goodarzi, A.; Yang, G. Q.; Erickson, C. L.

1985-01-01

Research performed at the University of Missouri-Columbia to devise and design a lower cost inverter induction motor drive for electrical propulsion of passenger vehicles is described. A two phase inverter motor system is recommended. The new design is predicted to provide comparable vehicle performance, improved reliability and a cost advantage for a high production vehicle, decreased total rating of the power semiconductor switches, and a somewhat simpler control hardware compared to the conventional three phase bridge inverter motor drive system. The major disadvantages of the two phase inverter motor drive are that it is larger and more expensive than a three phase machine, the design of snubbers for the power leakage inductances produce higher transient voltages, and the torque pulsations are relatively large because of the necessity to limit the inverter switching frequency to achieve high efficiency.

Design of an intelligent car

NASA Astrophysics Data System (ADS)

Na, Yongyi

2017-03-01

The design of simple intelligent car, using AT89S52 single chip microcomputer as the car detection and control core; The metal sensor TL - Q5MC induction to iron, to detect the way to send feedback to the signal of single chip microcomputer, make SCM according to the scheduled work mode to control the car in the area according to the predetermined speed, and the operation mode of the microcontroller choose different also can control the car driving along s-shaped iron; Use A44E hall element to detect the car speeds; Adopts 1602 LCD display time of car driving, driving the car to stop, take turns to show the car driving time, distance, average speed and the speed of time. This design has simple structure and is easy to implement, but are highly intelligent, humane, to a certain extent reflects the intelligence.

A Novelty Design Of Minimization Of Electrical Losses In A Vector Controlled Induction Machine Drive

NASA Astrophysics Data System (ADS)

Aryza, Solly; Irwanto, M.; Lubis, Zulkarnain; Putera Utama Siahaan, Andysah; Rahim, Robbi; Furqan, Mhd.

2018-01-01

The induction motor has in the industry . More attention has been a focus to develop and design of induction motor drive. With the method of vector control novelty prove the efficiency of induction motor over their entire speed range. In this paper desirable to design a loss minimization controller which can improve the efficiency. Also, this research described Modeling of an induction motor with core loss included. Realization of methods vector control for an induction motor drive with loss element included. The case of the loss minimization condition. The procedure was successful to calculate the gains of a PI controller. Though the problem of obtaining a robust and sensorless induction motor drive is by no means completely solved, the results obtained as part of this work point in a promising direction.

A Lever Coupling Mechanism in Dual-Mass Micro-Gyroscopes for Improving the Shock Resistance along the Driving Direction.

PubMed

Gao, Yang; Li, Hongsheng; Huang, Libin; Sun, Hui

2017-04-30

This paper presents the design and application of a lever coupling mechanism to improve the shock resistance of a dual-mass silicon micro-gyroscope with drive mode coupled along the driving direction without sacrificing the mechanical sensitivity. Firstly, the mechanical sensitivity and the shock response of the micro-gyroscope are theoretically analyzed. In the mechanical design, a novel lever coupling mechanism is proposed to change the modal order and to improve the frequency separation. The micro-gyroscope with the lever coupling mechanism optimizes the drive mode order, increasing the in-phase mode frequency to be much larger than the anti-phase one. Shock analysis results show that the micro-gyroscope structure with the designed lever coupling mechanism can notably reduce the magnitudes of the shock response and cut down the stress produced in the shock process compared with the traditional elastic coupled one. Simulations reveal that the shock resistance along the drive direction is greatly increased. Consequently, the lever coupling mechanism can change the gyroscope's modal order and improve the frequency separation by structurally offering a higher stiffness difference ratio. The shock resistance along the driving direction is tremendously enhanced without loss of the mechanical sensitivity.

49 CFR 571.126 - Standard No. 126; Electronic stability control systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cycle that is designed for low-speed, off-road driving, or (b) the vehicle is in a four-wheel drive configuration selected by the driver on the previous ignition cycle that is designed for operation at higher.... Light outriggers are designed with a maximum weight of 27 kg (59.5 lb) and a maximum roll moment of...

A Driving Simulator Evaluation of Cross-Sectional Design Elements and the Resulting Driving Behaviors

DOT National Transportation Integrated Search

2017-09-01

This research explores the relationship between the cross-sectional design elements and the impact on selected driver attributes such as speed profiles and lateral positioning. In this experiment a traditional collector-type base roadway of 1.5 miles...

Carryover effects of highly automated convoy driving on subsequent manual driving performance.

PubMed

Skottke, Eva-Maria; Debus, Günter; Wang, Lei; Huestegge, Lynn

2014-11-01

In the present study, we tested to what extent highly automated convoy driving involving small spacing ("platooning") may affect time headway (THW) and standard deviation of lateral position (SDLP) during subsequent manual driving. Although many previous studies have reported beneficial effects of automated driving, some research has also highlighted potential drawbacks, such as increased speed and reduced THW during the activation of semiautomated driving systems. Here, we rather focused on the question of whether switching from automated to manual driving may produce unwanted carryover effects on safety-relevant driving performance. We utilized a pre-post simulator design to measure THW and SDLP after highly automated driving and compared the data with those for a control group (manual driving throughout). Our data revealed that THW was reduced and SDLP increased after leaving the automation mode. A closer inspection of the data suggested that specifically the effect on THW is likely due to sensory and/or cognitive adaptation processes. Behavioral adaptation effects need to be taken into account in future implementations of automated convoy systems. Potential application areas of this research comprise automated freight traffic (truck convoys) and the design of driver assistance systems in general. Potential countermeasures against following at short distance as behavioral adaptation should be considered.

Infrastructure support for the UCF driving simulator

DOT National Transportation Integrated Search

2002-01-01

Last year, a proposal was funded to maintain the infrastructure of the UCF Driving Simulator Lab. It was designed to guarantee the long-term presence of support staff with proper expertise to maintain the operational effectiveness of the driving simu...

Sharing adverse drug event data using business intelligence technology.

PubMed

Horvath, Monica M; Cozart, Heidi; Ahmad, Asif; Langman, Matthew K; Ferranti, Jeffrey

2009-03-01

Duke University Health System uses computerized adverse drug event surveillance as an integral part of medication safety at 2 community hospitals and an academic medical center. This information must be swiftly communicated to organizational patient safety stakeholders to find opportunities to improve patient care; however, this process is encumbered by highly manual methods of preparing the data. Following the examples of other industries, we deployed a business intelligence tool to provide dynamic safety reports on adverse drug events. Once data were migrated into the health system data warehouse, we developed census-adjusted reports with user-driven prompts. Drill down functionality enables navigation from aggregate trends to event details by clicking report graphics. Reports can be accessed by patient safety leadership either through an existing safety reporting portal or the health system performance improvement Web site. Elaborate prompt screens allow many varieties of reports to be created quickly by patient safety personnel without consultation with the research analyst. The reduction in research analyst workload because of business intelligence implementation made this individual available to additional patient safety projects thereby leveraging their talents more effectively. Dedicated liaisons are essential to ensure clear communication between clinical and technical staff throughout the development life cycle. Design and development of the business intelligence model for adverse drug event data must reflect the eccentricities of the operational system, especially as new areas of emphasis evolve. Future usability studies examining the data presentation and access model are needed.

Evasive and Emergency Curriculum for Driver Education.

ERIC Educational Resources Information Center

1976

An advanced course to increase the student's driving ability and knowledge of the automobile is presented in this curriculum guide for use by high school driver education instructors. The course is designed for students who have been driving for 6 to 12 months or who have mastered basic driving skills. Focus is on advanced driving techniques,…

Driving for All Seasons and Reasons. Book Four. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Driving for All Seasons and Reasons is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver…

Driving and Dementia of the Alzheimer Type: Beliefs and Cessation Strategies among Stakeholders

ERIC Educational Resources Information Center

Perkinson, Margaret A.; Berg-Weger, Marla L.; Carr, David B.; Meuser, Thomas M.; Palmer, Janice L.; Buckles, Virginia D.; Powlishta, Kimberly K.; Foley, Daniel J.; Morris, John C.

2005-01-01

Purpose: Although driving by persons with Alzheimer's disease (AD) is an important public health concern, we know little about the attitudes and perceptions of key stakeholders regarding driving safety in these individuals or the factors that precipitate and influence driving assessment and cessation decisions. Design and Methods: We convened 10…

Control task substitution in semiautomated driving: does it matter what aspects are automated?

PubMed

Carsten, Oliver; Lai, Frank C H; Barnard, Yvonne; Jamson, A Hamish; Merat, Natasha

2012-10-01

The study was designed to show how driver attention to the road scene and engagement of a choice of secondary tasks are affected by the level of automation provided to assist or take over the basic task of vehicle control. It was also designed to investigate the difference between support in longitudinal control and support in lateral control. There is comparatively little literature on the implications of automation for drivers' engagement in the driving task and for their willingness to engage in non-driving-related activities. A study was carried out on a high-level driving simulator in which drivers experienced three levels of automation: manual driving, semiautomated driving with either longitudinal or lateral control provided, and highly automated driving with both longitudinal and lateral control provided. Drivers were free to pay attention to the roadway and traffic or to engage in a range of entertainment and grooming tasks. Engagement in the nondriving tasks increased from manual to semiautomated driving and increased further with highly automated driving. There were substantial differences in attention to the road and traffic between the two types of semiautomated driving. The literature on automation and the various task analyses of driving do not currently help to explain the effects that were found. Lateral support and longitudinal support may be the same in terms of levels of automation but appear to be regarded rather differently by drivers.

Classification of driving workload affected by highway alignment conditions based on classification and regression tree algorithm.

PubMed

Hu, Jiangbi; Wang, Ronghua

2018-02-17

Guaranteeing a safe and comfortable driving workload can contribute to reducing traffic injuries. In order to provide safe and comfortable threshold values, this study attempted to classify driving workload from the aspects of human factors mainly affected by highway geometric conditions and to determine the thresholds of different workload classifications. This article stated a hypothesis that the values of driver workload change within a certain range. Driving workload scales were stated based on a comprehensive literature review. Through comparative analysis of different psychophysiological measures, heart rate variability (HRV) was chosen as the representative measure for quantifying driving workload by field experiments. Seventy-two participants (36 car drivers and 36 large truck drivers) and 6 highways with different geometric designs were selected to conduct field experiments. A wearable wireless dynamic multiparameter physiological detector (KF-2) was employed to detect physiological data that were simultaneously correlated to the speed changes recorded by a Global Positioning System (GPS) (testing time, driving speeds, running track, and distance). Through performing statistical analyses, including the distribution of HRV during the flat, straight segments and P-P plots of modified HRV, a driving workload calculation model was proposed. Integrating driving workload scales with values, the threshold of each scale of driving workload was determined by classification and regression tree (CART) algorithms. The driving workload calculation model was suitable for driving speeds in the range of 40 to 120 km/h. The experimental data of 72 participants revealed that driving workload had a significant effect on modified HRV, revealing a change in driving speed. When the driving speed was between 100 and 120 km/h, drivers showed an apparent increase in the corresponding modified HRV. The threshold value of the normal driving workload K was between -0.0011 and 0.056 for a car driver and between -0.00086 and 0.067 for a truck driver. Heart rate variability was a direct and effective index for measuring driving workload despite being affected by multiple highway alignment elements. The driving workload model and the thresholds of driving workload classifications can be used to evaluate the quality of highway geometric design. A higher quality of highway geometric design could keep driving workload within a safer and more comfortable range. This study provided insight into reducing traffic injuries from the perspective of disciplinary integration of highway engineering and human factor engineering.

Dillard Drive Middle & Elementary School, Raleigh, North Carolina.

ERIC Educational Resources Information Center

Design Cost Data, 2001

2001-01-01

Presents design features of the Dillard Drive Middle & Elementary School (North Carolina) that incorporates daylighting in the majority of the classrooms, the gymnasium, dining room, and media center. The design also uses advanced lighting controls, fiber optic networking, automatic environmental controls, and an energy management system that…

Self-driving carsickness.

PubMed

Diels, Cyriel; Bos, Jelte E

2016-03-01

This paper discusses the predicted increase in the occurrence and severity of motion sickness in self-driving cars. Self-driving cars have the potential to lead to significant benefits. From the driver's perspective, the direct benefits of this technology are considered increased comfort and productivity. However, we here show that the envisaged scenarios all lead to an increased risk of motion sickness. As such, the benefits this technology is assumed to bring may not be capitalised on, in particular by those already susceptible to motion sickness. This can negatively affect user acceptance and uptake and, in turn, limit the potential socioeconomic benefits that this emerging technology may provide. Following a discussion on the causes of motion sickness in the context of self-driving cars, we present guidelines to steer the design and development of automated vehicle technologies. The aim is to limit or avoid the impact of motion sickness and ultimately promote the uptake of self-driving cars. Attention is also given to less well known consequences of motion sickness, in particular negative aftereffects such as postural instability, and detrimental effects on task performance and how this may impact the use and design of self-driving cars. We conclude that basic perceptual mechanisms need to be considered in the design process whereby self-driving cars cannot simply be thought of as living rooms, offices, or entertainment venues on wheels. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

New Design and Improvement of Planetary Gear Trains

NASA Technical Reports Server (NTRS)

Handschuh, Robert (Technical Monitor); Litvin, Faydor L.; Fuentes, Alfonso; Vecchiato, Daniele; Gonzalez-Perez, Ignacio

2004-01-01

The development of new types of planetary and planetary face-gear drives is proposed. The new designs are based on regulating backlash between the gears and modifying the tooth surfaces to improve the design. The goal of this work is to obtain a nearly uniform distribution of load between the planet gears. In addition, a new type of planetary face-gear drive was developed in this project.

Big Data, Models and Tools | Transportation Research | NREL

Science.gov Websites

displacement, and greenhouse gas reduction scenarios. New Tool Accelerates Design of Electric Vehicle Batteries design better, safer, and longer-lasting lithium-ion batteries for electric-drive vehicles through the Computer-Aided Engineering for Electric Drive Vehicle Batteries (CAEBAT) project. This month, ANSYS

Design process for applying the nonlocal thermal transport iSNB model to a Polar-Drive ICF simulation

NASA Astrophysics Data System (ADS)

Cao, Duc; Moses, Gregory; Delettrez, Jacques; Collins, Timothy

2014-10-01

A design process is presented for the nonlocal thermal transport iSNB (implicit Schurtz, Nicolai, and Busquet) model to provide reliable nonlocal thermal transport in polar-drive ICF simulations. Results from the iSNB model are known to be sensitive to changes in the SNB ``mean free path'' formula, and the latter's original form required modification to obtain realistic preheat levels. In the presented design process, SNB mean free paths are first modified until the model can match temperatures from Goncharov's thermal transport model in 1D temperature relaxation simulations. Afterwards the same mean free paths are tested in a 1D polar-drive surrogate simulation to match adiabats from Goncharov's model. After passing the two previous steps, the model can then be run in a full 2D polar-drive simulation. This research is supported by the University of Rochester Laboratory for Laser Energetics.

Automated generation of virtual scenarios in driving simulator from highway design data.

DOT National Transportation Integrated Search

2010-09-01

In 2008, the Texas Transportation Institute (TTI) began using a desktop driving simulator made by Realtime : Technologies, Inc. This system comes with a library of different roadway segment types that can be pieced : together to create driving scenar...

Impact of travel patterns and driving behavior on crash involvement.

DOT National Transportation Integrated Search

1983-07-21

This study was conducted to obtain statistically valid data on a variety of highway safety issues, such as attitudes toward drunk driving, use of safety belts and child safety seats, and to establish data regarding driving patterns. The study design ...

Investigation of a 4.5-Inch-Mean-Diameter Two-Stage Axial-Flow Turbine Suitable for Auxiliary Power Drives

NASA Technical Reports Server (NTRS)

Wong, Robert Y.; Monroe, Daniel E.

1959-01-01

The design and experimental investigation of a 4.5-inch-mean-diameter two-stage turbine are presented herein and used to study the effect of size on the efficiency of turbines in the auxiliary power drive class. The results of the experimental investigation indicated that design specific work was obtained at design speed at a total-to-static efficiency of 0.639. At design pressure ratio, design static-pressure distribution through the turbine was obtained with an equivalent specific work output of 33.2 Btu per pound and an efficiency of 0.656. It was found that, in the design of turbines in the auxiliary power drive class, Reynolds number plays an important part in the selection of the design efficiency. Comparison with theoretical efficiencies based on a loss coefficient and velocity diagrams are presented. Close agreement was obtained between theory and experiment when the loss coefficient was adjusted for changes in Reynolds number to the -1/5 power.

Position measurement of the direct drive motor of Large Aperture Telescope

NASA Astrophysics Data System (ADS)

Li, Ying; Wang, Daxing

2010-07-01

Along with the development of space and astronomy science, production of large aperture telescope and super large aperture telescope will definitely become the trend. It's one of methods to solve precise drive of large aperture telescope using direct drive technology unified designed of electricity and magnetism structure. A direct drive precise rotary table with diameter of 2.5 meters researched and produced by us is a typical mechanical & electrical integration design. This paper mainly introduces position measurement control system of direct drive motor. In design of this motor, position measurement control system requires having high resolution, and precisely aligning the position of rotor shaft and making measurement, meanwhile transferring position information to position reversing information corresponding to needed motor pole number. This system has chosen high precision metal band coder and absolute type coder, processing information of coders, and has sent 32-bit RISC CPU making software processing, and gained high resolution composite coder. The paper gives relevant laboratory test results at the end, indicating the position measurement can apply to large aperture telescope control system. This project is subsidized by Chinese National Natural Science Funds (10833004).

User-driven Cloud Implementation of environmental models and data for all

NASA Astrophysics Data System (ADS)

Gurney, R. J.; Percy, B. J.; Elkhatib, Y.; Blair, G. S.

2014-12-01

Environmental data and models come from disparate sources over a variety of geographical and temporal scales with different resolutions and data standards, often including terabytes of data and model simulations. Unfortunately, these data and models tend to remain solely within the custody of the private and public organisations which create the data, and the scientists who build models and generate results. Although many models and datasets are theoretically available to others, the lack of ease of access tends to keep them out of reach of many. We have developed an intuitive web-based tool that utilises environmental models and datasets located in a cloud to produce results that are appropriate to the user. Storyboards showing the interfaces and visualisations have been created for each of several exemplars. A library of virtual machine images has been prepared to serve these exemplars. Each virtual machine image has been tailored to run computer models appropriate to the end user. Two approaches have been used; first as RESTful web services conforming to the Open Geospatial Consortium (OGC) Web Processing Service (WPS) interface standard using the Python-based PyWPS; second, a MySQL database interrogated using PHP code. In all cases, the web client sends the server an HTTP GET request to execute the process with a number of parameter values and, once execution terminates, an XML or JSON response is sent back and parsed at the client side to extract the results. All web services are stateless, i.e. application state is not maintained by the server, reducing its operational overheads and simplifying infrastructure management tasks such as load balancing and failure recovery. A hybrid cloud solution has been used with models and data sited on both private and public clouds. The storyboards have been transformed into intuitive web interfaces at the client side using HTML, CSS and JavaScript, utilising plug-ins such as jQuery and Flot (for graphics), and Google Maps APIs. We have demonstrated that a cloud infrastructure can be used to assemble a virtual research environment that, coupled with a user-driven development approach, is able to cater to the needs of a wide range of user groups, from domain experts to concerned members of the general public.

Improved Speed Control System for the 87,000 HP Wind Tunnel Drive

NASA Technical Reports Server (NTRS)

Becks, Edward A.; Bencic, Timothy J.; Blumenthal, Philip Z.

1995-01-01

This paper describes the design, installation, and integrated systems tests for a new drive motor speed control system which was part of a recent rehab project for the NASA Lewis 8x6 Supersonic Wind Tunnel. The tunnel drive consists of three mechanically-coupled 29,000 HP wound rotor induction motors driving an axial flow compressor. Liquid rheostats are used to vary the impedance of the rotor circuits, thus varying the speed of the drive system. The new design utilizes a distributed digital control system with a dual touch screen CRT operator console to provide alarm monitoring, logging, and trending. The liquid rheostats are driven by brushtype servomotor systems with magnetostrictive linear displacement transducers used for position feedback. The new system achieved all goals for speed variations with load, motor load balance, and control of total power.

Improved speed control system for the 87,000 HP wind tunnel drive

NASA Astrophysics Data System (ADS)

Becks, Edward A.; Bencic, Timothy J.; Blumenthal, Philip Z.

1995-01-01

This paper describes the design, installation, and integrated systems tests for a new drive motor speed control system which was part of a recent rehab project for the NASA Lewis 8x6 Supersonic Wind Tunnel. The tunnel drive consists of three mechanically-coupled 29,000 HP wound rotor induction motors driving an axial flow compressor. Liquid rheostats are used to vary the impedance of the rotor circuits, thus varying the speed of the drive system. The new design utilizes a distributed digital control system with a dual touch screen CRT operator console to provide alarm monitoring, logging, and trending. The liquid rheostats are driven by brushtype servomotor systems with magnetostrictive linear displacement transducers used for position feedback. The new system achieved all goals for speed variations with load, motor load balance, and control of total power.

Study on the application of permanent magnet synchronous motors in underground belt conveyors

NASA Astrophysics Data System (ADS)

Ma, S. H.

2017-12-01

This paper analyzes and compares the advantages and disadvantages of several kinds of drive devices of belt conveyors from the angle of energy saving, and summarizes the application advantages and using problems of permanent magnet motor variable frequency drive system in belt conveyors. An example is given to demonstrate the energy saving effect of this system compared with other driving methods. This paper points out the application prospect of permanent magnet motor variable frequency drive system on belt conveyors and other large mining machines in coal mine. This paper is aimed to provide the design direction for the designer and the choice basis for the user on belt conveyor.

Design aspects of harmonic drive gear and performance improvement of its by problems identification: A review

NASA Astrophysics Data System (ADS)

Routh, Bikash

2018-04-01

The present paper aims at review on different aspects of harmonic drive gear to identify literature gap for future research. The present article is started first making the comparative study of harmonic drive gear over conventional gear, highlighting its historical background, its application, limitation etc. and then describing working principle of each and every components of it with detail dimensioning and modelling. The present article is further extended to study the different design aspects i.e. synthesis of tooth profiles, lubrication, stress, strain, torque, load sharing, kinematics error and vibration in details etc., identifying problems and then suggesting future perspective for the performance improvement of harmonic drive gear.

Miniature cryocooler developments for high operating temperatures at Thales Cryogenics

NASA Astrophysics Data System (ADS)

Arts, R.; Martin, J.-Y.; Willems, D.; Seguineau, C.; Van Acker, S.; Mullié, J. C.; Göbel, A.; Tops, M.; Le Bordays, J.; Etchanchu, T.; Benschop, A. A. J.

2015-05-01

In recent years there has been a drive towards miniaturized cooled IDCA solutions for low-power, low-mass, low-size products (SWaP). To support this drive, coolers are developed optimized for high-temperature, low heat load dewar-detector assemblies. In this paper, Thales Cryogenics development activities supporting SWaP are presented. Design choices are discussed and compared to various key requirements. Trade-off analysis results are presented on drive voltage, cold finger definition (length, material, diameter and sealing concept), and other interface considerations, including cold finger definition. In parallel with linear and rotary cooler options, designs for small-size high-efficiency drive electronics based on state-of-the-art architectures are presented.

An advanced pitch change mechanism incorporating a hybrid traction drive

NASA Technical Reports Server (NTRS)

Steinetz, B. M.; Loewenthal, S. H.; Sargisson, D. F.; White, G.

1984-01-01

A design of a propeller pitch control mechanism is described that meets the demanding requirements of a high-power, advanced turboprop. In this application, blade twisting moment torque can be comparable to that of the main reduction gearbox output: precise pitch control, reliability and compactness are all at a premium. A key element in the design is a compact, high-ratio hybrid traction drive which offers low torque ripple and high torsional stiffness. The traction drive couples a high speed electric motor/alternator unit to a ball screw that actuates the blade control links. The technical merits of this arrangement and the performance characteristics of the traction drive are discussed.

Design and simulation of a new bidirectional actuator for haptic systems featuring MR fluid

NASA Astrophysics Data System (ADS)

Hung, Nguyen Quoc; Tri, Diep Bao; Cuong, Vo Van; Choi, Seung-Bok

2017-04-01

In this research, a new configuration of bidirectional actuator featuring MR fluid (BMRA) is proposed for haptic application. The proposed BMRA consists of a driving disc, a driving housing and a driven disc. The driving disc is placed inside the driving housing and rotates counter to each other by a servo DC motor and a bevel gear system. The driven shaft is also placed inside the housing and next to the driving disc. The gap between the two disc and the gap between the discs and the housing are filled with MR fluid. On the driven disc, two mutual magnetic coils are placed. By applying currents to the two coils mutually, the torque at the output shaft, which is fixed to the driven disc, can be controlled with positive, zero or negative value. This make the actuator be suitable for haptic application. After a review of MR fluid and its application, configuration of the proposed BMRA is presented. The modeling of the actuator is then derived based on Bingham rheological model of MRF and magnetic finite element analysis (FEA). The optimal design of the actuator is then performed to minimize the mass of the BMRA. From the optimal design result, performance characteristics of the actuator is simulated and detailed design of a prototype actuator is conducted.

Advances in traction drive technology

NASA Technical Reports Server (NTRS)

Loewenthal, S. H.; Anderson, N. E.; Rohn, D. A.

1983-01-01

Traction drives are traced from early uses as main transmissions in automobiles at the turn of the century to modern, high-powered traction drives capable of transmitting hundreds of horsepower. Recent advances in technology are described which enable today's traction drive to be a serious candidate for off-highway vehicles and helicopter applications. Improvements in materials, traction fluids, design techniques, power loss and life prediction methods will be highlighted. Performance characteristics of the Nasvytis fixed-ratio drive are given. Promising future drive applications, such as helicopter main transmissions and servo-control positioning mechanisms are also addressed.

Exploring Challenges in Developing a Smart and Effective Assistive System for Improving the Experience of the Elderly Drivers

NASA Astrophysics Data System (ADS)

Jung, Sebin; Meng, Hong-Ying; Qin, Sheng-Feng

2017-09-01

As the overall population ages, driving-related accidents and injuries, associated with elderly drivers, have risen. Existing research about elderly drivers mainly focuses on factual data collection and analysis, indicating the elderly's growing fatal accident rates and their different behaviours compared to younger drivers. However, few research has focused on design-led practical solutions to mitigate the elderly's growing fatal accidents, by considering their usability and body conditions, afflicting the elderly, such as decreased vision, hearing, and reaction times. In this paper, first, current worldwide situations on growing fatal accident rates for elderly drivers is reviewed and the key impact factors are identified and discussed with regarding to usability and design trend in the automotive technology for elderly. Second, existing smart vehicle technology-based solutions to promote safe driving are explored and their pros and cons are discussed and analysed. Most of solutions are not created by people with driving difficulties, which are caused by health problems most commonly afflicting the elderly. Thirdly, diverse design-led research activities are taken, such as a survey, observation, and interviews to gain new understanding of what kinds of driving problems elderly drivers have and demonstrate how new system concepts could be developed for the elderly's benefits. Finally, it is found that the elderly's low vision and late reaction are main factors causing their driving difficulties. Based on this finding, usable vehicle system design ideas have been proposed, by utilising facial expression sensing technology as a solution. The proposed solutions would ensure reducing both the elderly's driving problems and high fatal accident rates and provide a more enjoyable driving environment for the elderly population.

Computerized Design and Generation of Gear Drives With a Localized Bearing Contact and a Low Level of Transmission Errors

NASA Technical Reports Server (NTRS)

Litvin, F.; Chen, J.; Seol, I.; Kim, D.; Lu, J.; Zhao, X.; Handschuh, R.

1996-01-01

A general approach developed for the computerized simulation of loaded gear drives is presented. In this paper the methodology used to localize the bearing contact, provide a parabolic function of transmission errors, and simulate meshing and contact of unloaded gear drives is developed. The approach developed is applied to spur and helical gears, spiral bevel gears, face-gear drives, and worm-gear drives with cylindrical worms.

Evaluation of Warm and Cold Shaft Designs for Large Multi-megawatt Direct Drive Offshore Superconducting Wind Generators

NASA Astrophysics Data System (ADS)

Kulkarni, Devdatta; Chen, Edward; Ho, Mantak; Karmaker, Haran

For offshore large multi-megawatt direct drive wind generators, because of its ability to generate high flux fields, superconducting (SC) technology can offer significant size and mass reduction over traditional technologies. However, cryogenic cooling design remains as one of the major obstacles to overcome. Different cryogenic cooling designs, such as warm shaft and cold shaft rotor design, present different advantages and challenges technically and commercially. This paper presents the investigations on both designs for large SC generators from manufacturability and service perspectives.

A Lever Coupling Mechanism in Dual-Mass Micro-Gyroscopes for Improving the Shock Resistance along the Driving Direction

PubMed Central

Gao, Yang; Li, Hongsheng; Huang, Libin; Sun, Hui

2017-01-01

This paper presents the design and application of a lever coupling mechanism to improve the shock resistance of a dual-mass silicon micro-gyroscope with drive mode coupled along the driving direction without sacrificing the mechanical sensitivity. Firstly, the mechanical sensitivity and the shock response of the micro-gyroscope are theoretically analyzed. In the mechanical design, a novel lever coupling mechanism is proposed to change the modal order and to improve the frequency separation. The micro-gyroscope with the lever coupling mechanism optimizes the drive mode order, increasing the in-phase mode frequency to be much larger than the anti-phase one. Shock analysis results show that the micro-gyroscope structure with the designed lever coupling mechanism can notably reduce the magnitudes of the shock response and cut down the stress produced in the shock process compared with the traditional elastic coupled one. Simulations reveal that the shock resistance along the drive direction is greatly increased. Consequently, the lever coupling mechanism can change the gyroscope’s modal order and improve the frequency separation by structurally offering a higher stiffness difference ratio. The shock resistance along the driving direction is tremendously enhanced without loss of the mechanical sensitivity. PMID:28468288

Design, modeling and control of a novel multi functional translational-rotary micro ultrasonic motor

NASA Astrophysics Data System (ADS)

Tuncdemir, Safakcan

The major goal of this thesis was to design and develop an actuator, which is capable of producing translational and rotary output motions in a compact structure with simple driving conditions, for the needs of small-scale actuators for micro robotic systems. Piezoelectric ultrasonic motors were selected as the target actuator schemes because of their unbeatable characteristics in the meso-scale range, which covers the structure sizes from hundred micrometers to ten millimeters and with operating ranges from few nanometers to centimeters. In order to meet the objectives and the design constraints, a number of key research tasks had to be undertaken. The design constraints and objectives were so stringent and entangled that none of the existing methods in literature could solve the research problems individually. Therefore, several unique methods were established to accomplish the research objectives. The methods produced novel solutions at every stage of design, development and modeling of the multi functional micro ultrasonic motor. Specifically, an ultrasonic motor utilizing slanted ceramics on a brass rod was designed. Because of the unique slanted ceramics design, longitudinal and torsional mode vibration modes could be obtained on the same structure. A ring shaped mobile element was loosely fitted on the metal rod stator. The mobile element moved in translational or rotational, depending on whether the vibration mode was longitudinal or torsional. A new ultrasonic motor drive method was required because none of the existing ultrasonic motor drive techniques were able to provide both output modes in a compact and cylindrical structure with the use of single drive source. By making use of rectangular wave drive signals, saw-tooth shaped displacement profile could be obtained at longitudinal and torsional resonance modes. Thus, inheriting the operating principle of smooth impact drive method, a new resonance type inertial drive was introduced. This new technique combines the advantages of inertial method with resonance drive. The motor that combines inertial drive at resonance will be a new type of ultrasonic motor, according to the classification of vibration types. A method to analyze the stator vibration by incorporating the piezoelectric loss coefficients was developed. By using the model, natural frequencies of the operating modes were predicted and exact formulations of the vibration displacements in longitudinal and torsional modes were obtained. The vibration model was in perfect agreement with the ATILA finite element analysis simulations even for different design parameters. The model was also used in design optimization and for theoretical explanation of the newly introduced motor drive technique. The theoretical analysis of the operating principle was verified with finite element analysis simulations and by vibration measurements. Several prototypes of motor were built in order to realize the dual function output as the main objective of this research. Translational output was observed for rectangular wave input signals at the resonance frequency of the fundamental longitudinal mode.The output mode changed to the rotational mode when the operating frequency switched for the fundamental torsional mode. While the mode of motor could be switched by switching the operating frequency, the direction of motion could be reversed by switching the duty cycle of rectangular input signals from D % to (100-D) %. A prototype (5 mm diameter, 25 mm total length produced 55 mm/s (translational) and 3 rad/s (rotary) speed under 40 mN blocking force, when the input signal was 40 V pp rectangular with 33% duty cycle. The motor speed at translational mode was characterized for different input voltage and output force. The meso-scale ultrasonic motor which utilizes smooth impact drive method, provided a unique ability to produce dual function with prominent output characteristics in a compact structure by using simple drive conditions.

Driving safety among patients with automatic implantable cardioverter defibrillators.

PubMed

Finch, N J; Leman, R B; Kratz, J M; Gillette, P C

1993-10-06

To determine the driving behavior of patients following the placement of automatic implantable cardioverter defibrillators (AICDs). Forty patients with AICDs (33 men, seven women; mean age, 62.7 years) responded to a questionnaire designed to ascertain driving behavior after hospital discharge. Despite medical advice never to drive again, 28 patients (70%) resumed driving, with the majority doing so by 8 months after AICD implantation. Of these, 11 (40%) identified themselves as the primary driver in their household. Fourteen (50%) drove daily. Two (7%) were driving and continued to drive during discharge of their AICDs. Twenty-five (91%) reported that they felt comfortable and safe while driving. A majority of patients with AICDs continue to drive after a proscription of this activity by health care workers.

77 FR 39561 - Advanced Braking Technologies That Rely on Forward-Looking Sensors; Request for Comments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-03

... test scenarios: driving over a 1-inch thick steel plate lying flat on the pavement (a plate often used... provide specific recommendations for other surrogate vehicle design considerations that should be... perform as designed (e.g., driving in the dark or in adverse weather)? What information should be...

Design Considerations of a Transverse Flux Machine for Direct-Drive Wind Turbine Applications: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husain, Tausif; Hasan, Iftekhar; Sozer, Yilmaz

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The TFM has a modular structure with quasi-U stator cores and ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating arrangement to achieve high air gap flux density. The design considerations for this TFM with respect to initial sizing, pole number selection, key design ratios, and pole shaping are presented in this paper. Pole number selection is critical in the design process of a TFM because it affects both the torque density and power factor under fixed magnetic andmore » changing electrical loading. Several key design ratios are introduced to facilitate the design procedure. The effect of pole shaping on back-emf and inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis. A prototype is under construction for experimental verification.« less

Design Considerations of a Transverse Flux Machine for Direct-Drive Wind Turbine Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husain, Tausif; Hasan, Iftekhar; Sozer, Yilmaz

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The TFM has a modular structure with quasi-U stator cores and ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating arrangement to achieve high air gap flux density. The design considerations for this TFM with respect to initial sizing, pole number selection, key design ratios, and pole shaping are presented in this paper. Pole number selection is critical in the design process of a TFM because it affects both the torque density and power factor under fixed magnetic andmore » changing electrical loading. Several key design ratios are introduced to facilitate the design procedure. The effect of pole shaping on back-emf and inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis. A prototype is under construction for experimental verification.« less

DriveWise: an interdisciplinary hospital-based driving assessment program.

PubMed

O'Connor, Margaret G; Kapust, Lissa R; Hollis, Ann M

2008-01-01

Health care professionals working with the elderly have opportunities through research and clinical practice to shape public policy affecting the older driver. This article describes DriveWise, an interdisciplinary hospital-based driving assessment program developed in response to clinical concerns about the driving safety of individuals with medical conditions. DriveWise clinicians use evidence-based, functional assessments to determine driving competence. In addition, the program was designed to meet the emotional needs of individuals whose driving safety has been called into question. To date, approximately 380 participants have been assessed through DriveWise. The following report details the DriveWise mission, DriveWise team members, and road test results. We continue to refine the assessment process to promote safety and support the dignity and independence of all participants. The DriveWise interdisciplinary approach to practice is a concrete example of how gerontological education across professions can have direct benefits to the older adult.

Computational fluid dynamics (CFD) in the design of a water-jet-drive system

NASA Technical Reports Server (NTRS)

Garcia, Roberto

1994-01-01

NASA/Marshall Space Flight Center (MSFC) has an ongoing effort to transfer to industry the technologies developed at MSFC for rocket propulsion systems. The Technology Utilization (TU) Office at MSFC promotes these efforts and accepts requests for assistance from industry. One such solicitation involves a request from North American Marine Jet, Inc. (NAMJ) for assistance in the design of a water-jet-drive system to fill a gap in NAMJ's product line. NAMJ provided MSFC with a baseline axial flow impeller design as well as the relevant working parameters (rpm, flow rate, etc.). This baseline design was analyzed using CFD, and significant deficiencies identified. Four additional analyses were performed involving MSFC changes to the geometric and operational parameters of the baseline case. Subsequently, the impeller was redesigned by NAMJ and analyzed by MSFC. This new configuration performs significantly better than the baseline design. Similar cooperative activities are planned for the design of the jet-drive inlet.

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Astrophysics Data System (ADS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-08-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

Design Considerations of a Transverse Flux Machine for Direct-Drive Wind Turbine Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husain, Tausif; Hasan, Iftekhar; Sozer, Yilmaz

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The proposed TFM has a modular structure with quasi-U stator cores and toroidal ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating setup to achieve high air gap flux density. Pole number selection is critical in the design process of a TFM as it affects both the torque density and power factor under fixed magnetic and changing electrical loading. Several key design ratios are introduced to facilitate the initial design procedure. The effect of pole shaping on back-EMF andmore » inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis (FEA). A proof-of-concept prototype was developed to experimentally validate the FEA results.« less

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Technical Reports Server (NTRS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-01-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

Design Considerations of a Transverse Flux Machine for Direct-Drive Wind Turbine Applications

DOE PAGES

Husain, Tausif; Hasan, Iftekhar; Sozer, Yilmaz; ...

2018-03-12

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The proposed TFM has a modular structure with quasi-U stator cores and toroidal ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating setup to achieve high air gap flux density. Pole number selection is critical in the design process of a TFM as it affects both the torque density and power factor under fixed magnetic and changing electrical loading. Several key design ratios are introduced to facilitate the initial design procedure. The effect of pole shaping on back-EMF andmore » inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis (FEA). A proof-of-concept prototype was developed to experimentally validate the FEA results.« less

Medium Duty ARRA Data Reporting and Analysis; NREL (National Renewable Energy Laboratory)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, Kenneth; Duran, Adam; Ragatz, Adam

Medium-duty (MD) electric vehicle (EV) data collection and analysis will help drive design, purchase, and research investments. Over 4 million miles and 160,000 driving days of EV driving data were collected under this project. Publicly available data help drive technology research, development, and deployment. Feeding the vocational database for future analysis will lead to a better understanding of usage and will result in better design optimization and technology implementation. The performance of a vehicle varies with drive cycle and cargo load - MD vehicles are 'multi-functional.' Environment and accessory loads affect vehicle range and in turn add cost by addingmore » battery capacity. MD EV vehicles can function in vocations traditionally serviced by gasoline or diesel vehicles. Facility implications (i.e., demand charges) need to be understood as part of site-based analysis for EV implementation.« less

Understanding commercial truck drivers' decision-makin process concerning distracted driving.

PubMed

Swedler, David I; Pollack, Keshia M; Gielen, Andrea C

2015-05-01

A concurrent mixed methods design was used to explore personal and workplace factors, informed by the Theory of Planned Behavior, that affect truck drivers' decision-making about distracted driving on the job. Qualitative data were collected via semi-structured interviews with experts in truck safety and distracted driving, and quantitative data were collected via online survey of truck drivers in the United States. Findings from the interviews illustrated how drivers perceived distractions and the importance of supervisors enforcing organizational distracted driving policies. Survey results found that behavioral intentions were most important in regards to texting and crash and near-crash outcomes, while perceived norms from management best described the correlation between dispatch device use and negative crash-related outcomes. By using a mixed methods design, rather than two separate studies, these findings revealed nuanced differences into the influence of supervisors on distracted driving. Copyright © 2015 Elsevier Ltd. All rights reserved.

An advanced pitch change mechanism incorporating a hybrid traction drive

NASA Technical Reports Server (NTRS)

Steinetz, B. M.; Sargisson, D. F.; White, G.; Loewenthal, S. H.

1984-01-01

A design of a propeller pitch control mechanism is described that meets the demanding requirements of a high-power, advanced turboprop. In this application, blade twisting moment torque can be comparable to that of the main reduction gearbox output: precise pitch control, reliability and compactness are all at a premium. A key element in the design is a compact, high-ratio hybrid traction drive which offers low torque ripple and high torsional stiffness. The traction drive couples a high speed electric motor/alternator unit to a ball screw that actuates the blade control links. The technical merits of this arrangement and the performance characteristics of the traction drive are discussed. Comparisons are made to the more conventional pitch control mechanisms.

Safe Driving Climate among Friends (SDCaF): A new scale.

PubMed

Guggenheim, Noga; Taubman-Ben-Ari, Orit

2018-01-01

Reckless driving among young people, especially young men, is a major cause of injury and fatalities the world over. Like other aspects of this age group, young drivers' driving behaviors and norms are influenced by the accepted social discourse of their peers. Yet despite extensive existing knowledge on young drivers, very few studies have dealt specifically with their characteristic friendship relations. This lacuna in the literature may reflect the absence of specific research tools for examining driving with friends. To fill this gap, we conducted a series of studies with 706 young drivers (aged 17-24) of both sexes aimed at developing and validating a multidimensional scale designed to examine the effect of the social relations of adolescents and young adults on their driving. Entitled Safe Driving Climate among Friends (SDCaF), the final scale consists of 19 items, which tap four dimensions of driving with friends: friends' pressure; social costs of driving with friends; communication with friends about driving; and shared commitment to safe driving. The validity of the scale was established by examining associations between its four dimensions and various variables of personality, friendship, and driving. The findings indicate good reliability and validity, with the three variables of resistance to peer influence, self-disclosure, and personal responsibility for safe driving yielding positive associations with the SDCaF dimensions communication and shared commitment to safe driving, and negative associations with the dimensions friends' pressure and social costs. General tendency to respond to social pressure was positively associated with the dimensions of friends' pressure and social costs, and negatively associated with shared commitment to safe driving. Gender differences were also found, with men scoring higher than women on friends' pressure, and lower than women on shared commitment to safe driving. The SDCaF can serve as a research tool, as well as a diagnostic instrument for detecting susceptibility to reckless driving among young drivers, thereby aiding in the design of targeted educational and intervention programs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Driver Education Curriculum Guide. Energy Conservation.

ERIC Educational Resources Information Center

Governor's Highway Safety Program Office, Columbus, OH.

Designed to provide high school students with information concerning energy-efficient driving, this curriculum guide covers techniques of conserving energy, efficient use of motor vehicles, safe driving techniques, and development of energy-efficient driving habits. The guide consists of six lessons: (1) Fuel Conservation: Why It Is Essential; (2)…

A drive based on an element made of a thermomechanical memory material

NASA Astrophysics Data System (ADS)

Krakhin, O. I.; Dubovik, I. N.; Rozarenova, Iu. A.

The advantages of using drives with active elements made of thermomechanical memory materials in aircraft structures are briefly reviewed. The choice of a particular type of active element based on a thermomechanical memory material is shown to depend on the specific operating conditions of the drive. The design of a rotary drive with an active element of TN-1 alloy is examined as an example.

An efficient supersonic wind tunnel drive system for Mach 2.5 flows

NASA Technical Reports Server (NTRS)

Wolf, Stephen W. D.; Laub, James A.; King, Lyndell S.

1991-01-01

A novel efficient drive system has been developed which provides for the continuous operation of a pitot Mach 2.5 wind tunnel at compression ratios down to 0.625:1. The drive system does not require an overpressure to start, and no hysteresis has been observed. The general design of the proof-of-concept wind tunnel using the new drive system and its modifications are described.

Large - scale Rectangular Ruler Automated Verification Device

NASA Astrophysics Data System (ADS)

Chen, Hao; Chang, Luping; Xing, Minjian; Xie, Xie

2018-03-01

This paper introduces a large-scale rectangular ruler automated verification device, which consists of photoelectric autocollimator and self-designed mechanical drive car and data automatic acquisition system. The design of mechanical structure part of the device refer to optical axis design, drive part, fixture device and wheel design. The design of control system of the device refer to hardware design and software design, and the hardware mainly uses singlechip system, and the software design is the process of the photoelectric autocollimator and the automatic data acquisition process. This devices can automated achieve vertical measurement data. The reliability of the device is verified by experimental comparison. The conclusion meets the requirement of the right angle test procedure.

Optimization of Driving Styles for Fuel Economy Improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malikopoulos, Andreas; Aguilar, Juan P.

2012-01-01

Modern vehicles have sophisticated electronic control units, particularly to control engine operation with respect to a balance between fuel economy, emissions, and power. These control units are designed for specific driving conditions and testing. However, each individual driving style is different and rarely meets those driving conditions. In the research reported here we investigate those driving style factors that have a major impact on fuel economy. An optimization framework is proposed with the aim of optimizing driving styles with respect to these driving factors. A set of polynomial metamodels are constructed to reflect the responses produced by changes of themore » driving factors. Then we compare the optimized driving styles to the original ones and evaluate the efficiency and effectiveness of the optimization formulation.« less

Forgiveness and Consideration of Future Consequences in Aggressive Driving

PubMed Central

Moore, Michael; Dahlen, Eric R.

2008-01-01

Most research on aggressive driving has focused on identifying aspects of driver personality which will exacerbate it (e.g., sensation seeking, impulsiveness, driving anger, etc.). The present study was designed to examine two theoretically relevant but previously unexplored personality factors predicted to reduce the risk of aggressive driving: trait forgiveness and consideration of future consequences. The utility of these variables in predicting aggressive driving and driving anger expression was evaluated among 316 college student volunteers. Hierarchical multiple regressions permitted an analysis of the incremental validity of these constructs beyond respondent gender, age, miles driven per week, and driving anger. Both forgiveness and consideration of future consequences contributed to the prediction of aggressive driving and driving anger expression, independent of driving anger. Research on aggressive driving may be enhanced by greater attention to adaptive, potentially risk-reducing traits. Moreover, forgiveness and consideration of future consequences may have implications for accident prevention. PMID:18760093

MOD-OA 200 kW wind turbine generator engineeringing

NASA Technical Reports Server (NTRS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.

1980-01-01

Engineering drawings and the detailed mechanical and electrical design of a horizontal-axis wind turbine designed for DOE at the NASA Lewis Research Center and installed in Clayton, New Mexico are discussed. The drawings show the hub, pitch change mechanism, drive train, nacelle equipment, yaw drive system, tower, foundation, electrical power systems, and the control and safety systems.

Experimental evaluation and design of unfilled and concrete-filled FRP composite piles, task 2 - FRP composite pile driving at the Richmond-Dresden bridge over the Kennebec River.

DOT National Transportation Integrated Search

2014-01-01

The overall goal of this project is the experimental evaluation and design of unfilled and concrete-filled FRP : composite piles for load-bearing in bridges. This report covers Task 2, FRP Composite Pile Driving at the : Richmond-Dresden Bridge over ...

Optimization design and dynamic analysis on the drive mechanisms of flapping-wing air vehicles based on flapping trajectories

NASA Astrophysics Data System (ADS)

Xie, Lingwang; Zhang, Xingwei; Luo, Pan; Huang, Panpan

2017-10-01

The optimization designs and dynamic analysis on the driving mechanism of flapping-wing air vehicles on base of flapping trajectory patterns is carried out in this study. Three different driving mechanisms which are spatial double crank-rocker, plane five-bar and gear-double slider, are systematically optimized and analysed by using the Mat lab and Adams software. After a series debugging on the parameter, the comparatively ideal flapping trajectories are obtained by the simulation of Adams. Present results indicate that different drive mechanisms output different flapping trajectories and have their unique characteristic. The spatial double crank-rocker mechanism can only output the arc flapping trajectory and it has the advantages of small volume, high flexibility and efficient space utilization. Both planar five-bar mechanism and gear-double slider mechanism can output the oval, figure of eight and double eight flapping trajectories. Nevertheless, the gear-double slider mechanism has the advantage of convenient parameter setting and better performance in output double eight flapping trajectory. This study can provide theoretical basis and helpful reference for the design of the drive mechanisms of flapping-wing air vehicles with different output flapping trajectories.

Using Mobile Devices to Connect Teachers and Museum Educators

NASA Astrophysics Data System (ADS)

Delen, Ibrahim; Krajcik, Joseph

2017-06-01

The use of mobile devices is increasing rapidly as a potential tool for science teaching. In this study, five educators (three middle school teachers and two museum educators) used a mobile application that supported the development of a driving question. Previous studies have noted that teachers make little effort to connect learning experiences between classrooms and museums, and few studies have focused on creating connections between teachers and museum educators. In this study, teachers and museum educators created an investigation together by designing a driving question in conjunction with the research group before field trips. During field trips, students collected their own data using iPods or iPads to take pictures or record videos of the exhibits. When students returned to the school, they used the museum data with their peers as they tried to answer the driving question. After completing the field trips, five educators were interviewed to investigate their experiences with designing driving questions and using mobile devices. Besides supporting students in data collection during the field trip, using mobile devices helped teachers to get the museum back to the classroom. Designing the driving question supported museum educators and teachers to plan the field trip collaboratively.

Google glass: a driver distraction cause or cure?

PubMed

Sawyer, Ben D; Finomore, Victor S; Calvo, Andres A; Hancock, P A

2014-11-01

We assess the driving distraction potential of texting with Google Glass (Glass), a mobile wearable platform capable of receiving and sending short-message-service and other messaging formats. A known roadway danger, texting while driving has been targeted by legislation and widely banned. Supporters of Glass claim the head-mounted wearable computer is designed to deliver information without concurrent distraction. Existing literature supports the supposition that design decisions incorporated in Glass might facilitate messaging for drivers. We asked drivers in a simulator to drive and use either Glass or a smartphone-based messaging interface, then interrupted them with an emergency brake event. Both the response event and subsequent recovery were analyzed. Glass-delivered messages served to moderate but did not eliminate distracting cognitive demands. A potential passive cost to drivers merely wearing Glass was also observed. Messaging using either device impaired driving as compared to driving without multitasking. Glass in not a panacea as some supporters claim, but it does point the way to design interventions that effect reduced load in multitasking. Discussions of these identified benefits are framed within the potential of new in-vehicle systems that bring both novel forms of distraction and tools for mitigation into the driver's seat.

Linkage design effect on the reliability of surface-micromachined microengines driving a load

NASA Astrophysics Data System (ADS)

Tanner, Danelle M.; Peterson, Kenneth A.; Irwin, Lloyd W.; Tangyunyong, Paiboon; Miller, William M.; Eaton, William P.; Smith, Norman F.; Rodgers, M. Steven

1998-09-01

The reliability of microengines is a function of the design of the mechanical linkage used to connect the electrostatic actuator to the drive. We have completed a series of reliability stress tests on surface micromachined microengines driving an inertial load. In these experiments, we used microengines that had pin mechanisms with guides connecting the drive arms to the electrostatic actuators. Comparing this data to previous results using flexure linkages revealed that the pin linkage design was less reliable. The devices were stressed to failure at eight frequencies, both above and below the measured resonance frequency of the microengine. Significant amounts of wear debris were observed both around the hub and pin joint of the drive gear. Additionally, wear tracks were observed in the area where the moving shuttle rubbed against the guides of the pin linkage. At each frequency, we analyzed the statistical data yielding a lifetime (t50) for median cycles to failure and (sigma) , the shape parameter of the distribution. A model was developed to describe the failure data based on fundamental wear mechanisms and forces exhibited in mechanical resonant systems. The comparison to the model will be discussed.

Design study of toroidal traction CVT for electric vehicles

NASA Technical Reports Server (NTRS)

Raynard, A. E.; Kraus, J.; Bell, D. D.

1980-01-01

The development, evaluation, and optimization of a preliminary design concept for a continuously variable transmission (CVT) to couple the high-speed output shaft of an energy storage flywheel to the drive train of an electric vehicle is discussed. An existing computer simulation program was modified and used to compare the performance of five CVT design configurations. Based on this analysis, a dual-cavity full-toroidal drive with regenerative gearing is selected for the CVT design configuration. Three areas are identified that will require some technological development: the ratio control system, the traction fluid properities, and evaluation of the traction contact performance. Finally, the suitability of the selected CVT design concept for alternate electric and hybrid vehicle applications and alternate vehicle sizes and maximum output torques is determined. In all cases the toroidal traction drive design concept is applicable to the vehicle system. The regenerative gearing could be eliminated in the electric powered vehicle because of the reduced ratio range requirements. In other cases the CVT with regenerative gearing would meet the design requirements after appropriate adjustments in size and reduction gearing ratio.

Does the S.D.E.P. increase performance?

NASA Astrophysics Data System (ADS)

Syltebo, Andy

2003-05-01

Through the guidance of the program, "Physical Systems," at The Evergreen State College in Olympia Washington, Andy Syltebo will be investigating how the Surface Drive Enhancement Project will affect the performance of a planing hull powered by surface drive propulsion. A radio controlled model boat of the forementioned design is the prototype vehicle used for experimentation and analysis. The idea of this project revolves around harnessing the energy in the water of a rooster tail ejected from the wake of a surface drive propeller of a boat with a planing hull design. The Surface Drive Enhancement Project (S.D.E.P. for short) is an angled set of adjustable platforms placed in the path of the rooster tail. Theoretically, it experiences the normal force of the water on its surface which, through conservation of momentum, distributes a force on the boat, with which the S.D.E.P. is attached, in both the upwards and forwards directions. This design will be tested and documented to see if it increases forward velocity without sacrificing handling characteristics.

The 3600 hp split-torque helicopter transmission

NASA Technical Reports Server (NTRS)

White, G.

1985-01-01

Final design details of a helicopter transmission that is powered by GE twin T 700 engines each rated at 1800 hp are presented. It is demonstrated that in comparison with conventional helicopter transmission arrangements the split torque design offers: weight reduction of 15%; reduction in drive train losses of 9%; and improved reliability resulting from redundant drive paths between the two engines and the main shaft. The transmission fits within the NASA LeRC 3000 hp Test Stand and accepts the existing positions for engine inputs, main shaft, connecting drive shafts, and the cradle attachment points. One necessary change to the test stand involved gear trains of different ratio in the tail drive gearbox. Progressive uprating of engine input power from 3600 to 4500 hp twin engine rating is allowed for in the design. In this way the test transmission will provide a base for several years of analytical, research, and component development effort targeted at improving the performance and reliability of helicopter transmission.

Off-Design Performance of a Multi-Stage Supersonic Turbine

NASA Technical Reports Server (NTRS)

Dorney, Daniel J.; Griffin, Lisa W.; Huber, Frank; Sondak, Douglas L.

2003-01-01

The drive towards high-work turbines has led to designs which can be compact, transonic, supersonic, counter rotating, or use a dense drive gas. These aggressive designs can lead to strong unsteady secondary flows and flow separation. The amplitude and extent of these unsteady flow phenomena can be amplified at off-design operating conditions. Pre-test off-design predictions have been performed for a new two-stage supersonic turbine design that is currently being tested in air. The simulations were performed using a three-dimensional unsteady Navier-Stokes analysis, and the predicted results have been compared with solutions from a validated meanline analysis.

Development of cable drive systems for an automated assembly project

NASA Technical Reports Server (NTRS)

Monroe, Charles A., Jr.

1990-01-01

In a robotic assembly project, a method was needed to accurately position a robot and a structure which the robot was to assemble. The requirements for high precision and relatively long travel distances dictated the use of cable drive systems. The design of the mechanisms used in translating the robot and in rotating the assembly under construction is discussed. The design criteria are discussed, and the effect of particular requirements on the design is noted. Finally, the measured performance of the completed mechanism is compared with design requirements.

Conceptual design study of a visual system for a rotorcraft simulator and some advances in platform motion utilization

NASA Technical Reports Server (NTRS)

Sinacori, J. B.

1980-01-01

A conceptual design of a visual system for a rotorcraft flight simulator is presented. Also, drive logic elements for a coupled motion base for such a simulator are given. The design is the result of an assessment of many potential arrangements of electro-optical elements and is a concept considered feasible for the application. The motion drive elements represent an example logic for a coupled motion base and is essentially an appeal to the designers of such logic to combine their washout and braking functions.

Design of an immersive simulator for assisted power wheelchair driving.

PubMed

Devigne, Louise; Babel, Marie; Nouviale, Florian; Narayanan, Vishnu K; Pasteau, Francois; Gallien, Philippe

2017-07-01

Driving a power wheelchair is a difficult and complex visual-cognitive task. As a result, some people with visual and/or cognitive disabilities cannot access the benefits of a power wheelchair because their impairments prevent them from driving safely. In order to improve their access to mobility, we have previously designed a semi-autonomous assistive wheelchair system which progressively corrects the trajectory as the user manually drives the wheelchair and smoothly avoids obstacles. Developing and testing such systems for wheelchair driving assistance requires a significant amount of material resources and clinician time. With Virtual Reality technology, prototypes can be developed and tested in a risk-free and highly flexible Virtual Environment before equipping and testing a physical prototype. Additionally, users can "virtually" test and train more easily during the development process. In this paper, we introduce a power wheelchair driving simulator allowing the user to navigate with a standard wheelchair in an immersive 3D Virtual Environment. The simulation framework is designed to be flexible so that we can use different control inputs. In order to validate the framework, we first performed tests on the simulator with able-bodied participants during which the user's Quality of Experience (QoE) was assessed through a set of questionnaires. Results show that the simulator is a promising tool for future works as it generates a good sense of presence and requires rather low cognitive effort from users.

Designing a System for Computer-Assisted Instruction in Road Education: A First Evaluation.

ERIC Educational Resources Information Center

Garcia-Ros, Rafael; Montoro, Luis; Valero, Pedro; Bayarri, Salvador; Martinez, Tomas

1999-01-01

Describes SIVAS, a computer-based system for driver education based on visual simulation that was developed in Spain to support theoretical concepts about driving in driving schools. Explains how teachers can select pre-built scenarios related to driving lessons in order to make up a lecture. (Author/LRW)

A 15 MHz bandwidth, 60 V{sub pp}, low distortion power amplifier for driving high power piezoelectric transducers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Capineri, Lorenzo, E-mail: lorenzo.capineri@unifi.it

2014-10-01

This paper presents the design and the realization of a linear power amplifier with large bandwidth (15 MHz) capable of driving low impedance ultrasonic transducers. The output current driving capability (up to 5 A) and low distortion makes it suitable for new research applications using high power ultrasound in the medical and industrial fields. The electronic design approach is modular so that the characteristics can be scaled according to specific applications and implementation details for the circuit layout are reported. Finally the characterization of the power amplifier module is presented.

Design Study for an Actively Terrain-Adaptive Off-Road Vehicle.

DTIC Science & Technology

1982-06-03

at right. I-u M K_ £.IKAI 3-CPTF. 4.1.1K L019SN $-DATA I-INPiUg 7.W.’GCS. LOT I.IIIT 1191?M’ I.1Ki ANIMATION a.RtMDI- heMI .tfANIMTION T%*9I .IPU DRIVE ...relationship between drive actuator displacement and foot displacement achievable with this geometry is attractive from the point of view of the control...with progress in optimizing the drive actuator mounting to minimize non-linearity have led to retention of the four-bar leg as the operative design. The

Experimental research of flow servo-valve

NASA Astrophysics Data System (ADS)

Takosoglu, Jakub

Positional control of pneumatic drives is particularly important in pneumatic systems. Some methods of positioning pneumatic cylinders for changeover and tracking control are known. Choking method is the most development-oriented and has the greatest potential. An optimal and effective method, particularly when applied to pneumatic drives, has been searched for a long time. Sophisticated control systems with algorithms utilizing artificial intelligence methods are designed therefor. In order to design the control algorithm, knowledge about real parameters of servo-valves used in control systems of electro-pneumatic servo-drives is required. The paper presents the experimental research of flow servo-valve.

The effects of iPod and text-messaging use on driver distraction: a bio-behavioral analysis.

PubMed

Mouloua, M; Ahern, A; Quevedo, A; Jaramillo, D; Rinalducci, E; Smither, J; Alberti, P; Brill, C

2012-01-01

This study was designed to empirically examine the effects of iPod device and text-messaging activities on driver distraction. Sixty participants were asked to perform a driving simulation task while searching for songs using an iPod device or text messaging. Driving errors as measured by lane deviations were recorded and analyzed as a function of the distracters. Physiological measures (EEG) were also recorded during the driving phases in order to measure participant levels of cortical arousal. It was hypothesized that iPod use and text messaging would result in a profound effect on driving ability. The results showed a significant effect of iPod use and text-messaging on driving performance. Increased numbers of driving errors were recorded during the iPod and text-messaging phases than the pre- and post-allocation phases. Higher levels of Theta activity were also observed during the iPod and Text-messaging phase than the pre- and post-allocation phases. Implications for in-vehicle systems design, training, and safety are also discussed.

Pile Driving

NASA Technical Reports Server (NTRS)

1987-01-01

Machine-oriented structural engineering firm TERA, Inc. is engaged in a project to evaluate the reliability of offshore pile driving prediction methods to eventually predict the best pile driving technique for each new offshore oil platform. Phase I Pile driving records of 48 offshore platforms including such information as blow counts, soil composition and pertinent construction details were digitized. In Phase II, pile driving records were statistically compared with current methods of prediction. Result was development of modular software, the CRIPS80 Software Design Analyzer System, that companies can use to evaluate other prediction procedures or other data bases.

Conservation demands safe gene drive

PubMed Central

Esvelt, Kevin M.

2017-01-01

Interest in developing gene drive systems to control invasive species is growing, with New Zealand reportedly considering the nascent technology as a way to locally eliminate the mammalian pests that threaten its unique flora and fauna. If gene drives successfully eradicated these invasive populations, many would rejoice, but what are the possible consequences? Here, we explore the risk of accidental spread posed by self-propagating gene drive technologies, highlight new gene drive designs that might achieve better outcomes, and explain why we need open and international discussions concerning a technology that could have global ramifications. PMID:29145398

Conservation demands safe gene drive.

PubMed

Esvelt, Kevin M; Gemmell, Neil J

2017-11-01

Interest in developing gene drive systems to control invasive species is growing, with New Zealand reportedly considering the nascent technology as a way to locally eliminate the mammalian pests that threaten its unique flora and fauna. If gene drives successfully eradicated these invasive populations, many would rejoice, but what are the possible consequences? Here, we explore the risk of accidental spread posed by self-propagating gene drive technologies, highlight new gene drive designs that might achieve better outcomes, and explain why we need open and international discussions concerning a technology that could have global ramifications.

Satellite-instrument system engineering best practices and lessons

NASA Astrophysics Data System (ADS)

Schueler, Carl F.

2009-08-01

This paper focuses on system engineering development issues driving satellite remote sensing instrumentation cost and schedule. A key best practice is early assessment of mission and instrumentation requirements priorities driving performance trades among major instrumentation measurements: Radiometry, spatial field of view and image quality, and spectral performance. Key lessons include attention to technology availability and applicability to prioritized requirements, care in applying heritage, approaching fixed-price and cost-plus contracts with appropriate attention to risk, and assessing design options with attention to customer preference as well as design performance, and development cost and schedule. A key element of success either in contract competition or execution is team experience. Perhaps the most crucial aspect of success, however, is thorough requirements analysis and flowdown to specifications driving design performance with sufficient parameter margin to allow for mistakes or oversights - the province of system engineering from design inception to development, test and delivery.

Evaluating In-Car Movements in the Design of Mindful Commute Interventions: Exploratory Study.

PubMed

Paredes, Pablo Enrique; Hamdan, Nur Al-Huda; Clark, Dav; Cai, Carrie; Ju, Wendy; Landay, James A

2017-12-04

The daily commute could be a right moment to teach drivers to use movement or breath towards improving their mental health. Long commutes, the relevance of transitioning from home to work, and vice versa and the privacy of commuting by car make the commute an ideal scenario and time to perform mindful exercises safely. Whereas driving safety is paramount, mindful exercises might help commuters decrease their daily stress while staying alert. Increasing vehicle automation may present new opportunities but also new challenges. This study aimed to explore the design space for movement-based mindful interventions for commuters. We used qualitative analysis of simulated driving experiences in combination with simple movements to obtain key design insights. We performed a semistructured viability assessment in 2 parts. First, a think-aloud technique was used to obtain information about a driving task. Drivers (N=12) were given simple instructions to complete movements (configural or breath-based) while engaged in either simple (highway) or complex (city) simulated urban driving tasks using autonomous and manual driving modes. Then, we performed a matching exercise where participants could experience vibrotactile patterns from the back of the car seat and map them to the prior movements. We report a summary of individual perceptions concerning different movements and vibrotactile patterns. Beside describing situations within a drive when it may be more likely to perform movement-based interventions, we also describe movements that may interfere with driving and those that may complement it well. Furthermore, we identify movements that could be conducive to a more relaxing commute and describe vibrotactile patterns that could guide such movements and exercises. We discuss implications for design such as the influence of driving modality on the adoption of movement, need for personal customization, the influence that social perception has on participants, and the potential role of prior awareness of mindful techniques in the adoption of new movement-based interventions. This exploratory study provides insights into which types of movements could be better suited to design mindful interventions to reduce stress for commuters, when to encourage such movements, and how best to guide them using noninvasive haptic stimuli embedded in the car seat. ©Pablo Enrique Paredes, Nur Al-Huda Hamdan, Dav Clark, Carrie Cai, Wendy Ju, James A Landay. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 04.12.2017.

Evaluating In-Car Movements in the Design of Mindful Commute Interventions: Exploratory Study

PubMed Central

Hamdan, Nur Al-Huda; Clark, Dav; Cai, Carrie; Ju, Wendy; Landay, James A

2017-01-01

Background The daily commute could be a right moment to teach drivers to use movement or breath towards improving their mental health. Long commutes, the relevance of transitioning from home to work, and vice versa and the privacy of commuting by car make the commute an ideal scenario and time to perform mindful exercises safely. Whereas driving safety is paramount, mindful exercises might help commuters decrease their daily stress while staying alert. Increasing vehicle automation may present new opportunities but also new challenges. Objective This study aimed to explore the design space for movement-based mindful interventions for commuters. We used qualitative analysis of simulated driving experiences in combination with simple movements to obtain key design insights. Methods We performed a semistructured viability assessment in 2 parts. First, a think-aloud technique was used to obtain information about a driving task. Drivers (N=12) were given simple instructions to complete movements (configural or breath-based) while engaged in either simple (highway) or complex (city) simulated urban driving tasks using autonomous and manual driving modes. Then, we performed a matching exercise where participants could experience vibrotactile patterns from the back of the car seat and map them to the prior movements. Results We report a summary of individual perceptions concerning different movements and vibrotactile patterns. Beside describing situations within a drive when it may be more likely to perform movement-based interventions, we also describe movements that may interfere with driving and those that may complement it well. Furthermore, we identify movements that could be conducive to a more relaxing commute and describe vibrotactile patterns that could guide such movements and exercises. We discuss implications for design such as the influence of driving modality on the adoption of movement, need for personal customization, the influence that social perception has on participants, and the potential role of prior awareness of mindful techniques in the adoption of new movement-based interventions. Conclusions This exploratory study provides insights into which types of movements could be better suited to design mindful interventions to reduce stress for commuters, when to encourage such movements, and how best to guide them using noninvasive haptic stimuli embedded in the car seat. PMID:29203458

The Effects of Dextromethorphan on Driving Performance and the Standardized Field Sobriety Test.

PubMed

Perry, Paul J; Fredriksen, Kristian; Chew, Stephanie; Ip, Eric J; Lopes, Ingrid; Doroudgar, Shadi; Thomas, Kelan

2015-09-01

Dextromethorphan (DXM) is abused most commonly among adolescents as a recreational drug to generate a dissociative experience. The objective of the study was to assess driving with and without DXM ingestion. The effects of one-time maximum daily doses of DXM 120 mg versus a guaifenesin 400 mg dose were compared among 40 healthy subjects using a crossover design. Subjects' ability to drive was assessed by their performance in a driving simulator (STISIM® Drive driving simulator software) and by conducting a standardized field sobriety test (SFST) administered 1-h postdrug administration. The one-time dose of DXM 120 mg did not demonstrate driving impairment on the STISIM® Drive driving simulator or increase SFST failures compared to guaifenesin 400 mg. Doses greater than the currently recommended maximum daily dose of 120 mg are necessary to perturb driving behavior. © 2015 American Academy of Forensic Sciences.

Design and fabrication of a 1-DOF drive mode and 2-DOF sense mode micro-gyroscope using SU-8 based UV-LIGA process

NASA Astrophysics Data System (ADS)

Verma, Payal; Juneja, Sucheta; Savelyev, Dmitry A.; Khonina, Svetlana N.; Gopal, Ram

2016-04-01

This paper presents design and fabrication of a 1-DOF (degree-of-freedom) drive mode and 2-DOF sense mode micro-gyroscope. It is an inherently robust structure and offers a high sense frequency bandwidth. The proposed design utilizes resonance of the1-DOF drive mode oscillator and employs dynamic amplification concept in sense modes to increase the sensitivity while maintaining robustness. The 2-DOF in the sense direction renders the device immune to process imperfections and environmental effects. The design is simulated using FEA software (CoventorWare®). The device is designed considering process compatibility with SU-8 based UV-LIGA process, which is an economical fabrication technique. The complete fabrication process is presented along with SEM images of the fabricated device. The device has 9 µm thick Nickel as the key structural layer with an overall reduced key structure size of 2.2 mm by 2.1 mm.

Rotating rake design for unique measurement of fan-generated spinning acoustic modes

NASA Technical Reports Server (NTRS)

Konno, Kevin E.; Hausmann, Clifford R.

1993-01-01

In light of the current emphasis on noise reduction in subsonic aircraft design, NASA has been actively studying the source of and propagation of noise generated by subsonic fan engines. NASA/LeRC has developed and tested a unique method of accurately measuring these spinning acoustic modes generated by an experimental fan. This mode measuring method is based on the use of a rotating microphone rake. Testing was conducted in the 9 x 15 Low-speed Wind Tunnel. The rotating rake was tested with the Advanced Ducted Propeller (ADP) model. This memorandum discusses the design and performance of the motor/drive system for the fan-synchronized rotating acoustic rake. This novel motor/drive design approach is now being adapted for additional acoustic mode studies in new test rigs as baseline data for the future design of active noise control for subsonic fan engines. Included in this memorandum are the research requirements, motor/drive specifications, test performance results, and a description of the controls and software involved.

Bio-inspired piezoelectric linear motor driven by a single-phase harmonic wave with an asymmetric stator.

PubMed

Pan, Qiaosheng; Miao, Enming; Wu, Bingxuan; Chen, Weikang; Lei, Xiujun; He, Liangguo

2017-07-01

A novel, bio-inspired, single-phase driven piezoelectric linear motor (PLM) using an asymmetric stator was designed, fabricated, and tested to avoid mode degeneracy and to simplify the drive mechanism of a piezoelectric motor. A piezoelectric transducer composed of two piezoelectric stacks and a displacement amplifier was used as the driving element of the PLM. Two simple and specially designed claws performed elliptical motion. A numerical simulation was performed to design the stator and determine the feasibility of the design mechanism of the PLM. Moreover, an experimental setup was built to validate the working principles, as well as to evaluate the performance, of the PLM. The prototype motor outputs a no-load speed of 233.7 mm/s at a voltage of 180 V p-p and a maximum thrust force of 2.3 N under a preload of 10 N. This study verified the feasibility of the proposed design and provided a method to simplify the driving harmonic signal and structure of PLMs.

The Effect of Rotor Cruise Tip Speed, Engine Technology and Engine/Drive System RPM on the NASA Large Civil Tiltrotor (LCTR2) Size and Performance

NASA Technical Reports Server (NTRS)

Robuck, Mark; Wilkerson, Joseph; Maciolek, Robert; Vonderwell, Dan

2012-01-01

A multi-year study was conducted under NASA NNA06BC41C Task Order 10 and NASA NNA09DA56C task orders 2, 4, and 5 to identify the most promising propulsion system concepts that enable rotor cruise tip speeds down to 54% of the hover tip speed for a civil tiltrotor aircraft. Combinations of engine RPM reduction and 2-speed drive systems were evaluated. Three levels of engine and the drive system advanced technology were assessed; 2015, 2025 and 2035. Propulsion and drive system configurations that resulted in minimum vehicle gross weight were identified. Design variables included engine speed reduction, drive system speed reduction, technology, and rotor cruise propulsion efficiency. The NASA Large Civil Tiltrotor, LCTR, aircraft served as the base vehicle concept for this study and was resized for over thirty combinations of operating cruise RPM and technology level, quantifying LCTR2 Gross Weight, size, and mission fuel. Additional studies show design sensitivity to other mission ranges and design airspeeds, with corresponding relative estimated operational cost. The lightest vehicle gross weight solution consistently came from rotor cruise tip speeds between 422 fps and 500 fps. Nearly equivalent results were achieved with operating at reduced engine RPM with a single-speed drive system or with a two-speed drive system and 100% engine RPM. Projected performance for a 2025 engine technology provided improved fuel flow over a wide range of operating speeds relative to the 2015 technology, but increased engine weight nullified the improved fuel flow resulting in increased aircraft gross weights. The 2035 engine technology provided further fuel flow reduction and 25% lower engine weight, and the 2035 drive system technology provided a 12% reduction in drive system weight. In combination, the 2035 technologies reduced aircraft takeoff gross weight by 14% relative to the 2015 technologies.

Linear Back-Drive Differentials

NASA Technical Reports Server (NTRS)

Waydo, Peter

2003-01-01

Linear back-drive differentials have been proposed as alternatives to conventional gear differentials for applications in which there is only limited rotational motion (e.g., oscillation). The finite nature of the rotation makes it possible to optimize a linear back-drive differential in ways that would not be possible for gear differentials or other differentials that are required to be capable of unlimited rotation. As a result, relative to gear differentials, linear back-drive differentials could be more compact and less massive, could contain fewer complex parts, and could be less sensitive to variations in the viscosities of lubricants. Linear back-drive differentials would operate according to established principles of power ball screws and linear-motion drives, but would utilize these principles in an innovative way. One major characteristic of such mechanisms that would be exploited in linear back-drive differentials is the possibility of designing them to drive or back-drive with similar efficiency and energy input: in other words, such a mechanism can be designed so that a rotating screw can drive a nut linearly or the linear motion of the nut can cause the screw to rotate. A linear back-drive differential (see figure) would include two collinear shafts connected to two parts that are intended to engage in limited opposing rotations. The linear back-drive differential would also include a nut that would be free to translate along its axis but not to rotate. The inner surface of the nut would be right-hand threaded at one end and left-hand threaded at the opposite end to engage corresponding right- and left-handed threads on the shafts. A rotation and torque introduced into the system via one shaft would drive the nut in linear motion. The nut, in turn, would back-drive the other shaft, creating a reaction torque. Balls would reduce friction, making it possible for the shaft/nut coupling on each side to operate with 90 percent efficiency.

77 FR 15398 - Attentive Driving: Countermeasures for Distraction Forum

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-15

... include distracted driving laws and enforcement, changing attitudes and behaviors through education and... Attitudes and Behaviors Panel 4: Technology and Design Countermeasures Summary and Closing Remarks The full...

The Rocket Equation Improvement under ICF Implosion Experiment

NASA Astrophysics Data System (ADS)

Wang, Yanbin; Zheng, Zhijian

2013-10-01

The ICF explosion process has been studied in details. The rocket equation has been improved in explosive process by introducing the pressure parameter of fuel. Some methods could be drawn by the improved rocket equation. And the methods could be used to improve ICF target design, driving pulse design and experimental design. The First is to increase ablation pressure. The second is to decrease pressure of fuel. The third is to use larger diameter of target sphere. And the forth is to a shorten driving pulse.

Design and analysis of new fault-tolerant permanent magnet motors for four-wheel-driving electric vehicles

NASA Astrophysics Data System (ADS)

Liu, Guohai; Gong, Wensheng; Chen, Qian; Jian, Linni; Shen, Yue; Zhao, Wenxiang

2012-04-01

In this paper, a novel in-wheel permanent-magnet (PM) motor for four-wheel-driving electrical vehicles is proposed. It adopts an outer-rotor topology, which can help generate a large drive torque, in order to achieve prominent dynamic performance of the vehicle. Moreover, by adopting single-layer concentrated-windings, fault-tolerant teeth, and the optimal combination of slot and pole numbers, the proposed motor inherently offers negligible electromagnetic coupling between different phase windings, hence, it possesses a fault-tolerant characteristic. Meanwhile, the phase back electromotive force waveforms can be designed to be sinusoidal by employing PMs with a trapezoidal shape, eccentric armature teeth, and unequal tooth widths. The electromagnetic performance is comprehensively investigated and the optimal design is conducted by using the finite-element method.

An Improved Power Quality Based Sheppard-Taylor Converter Fed BLDC Motor Drive

NASA Astrophysics Data System (ADS)

Singh, Bhim; Bist, Vashist

2015-12-01

This paper deals with the design and analysis of a power factor correction based Sheppard-Taylor converter fed brushless dc motor (BLDCM) drive. The speed of the BLDCM is controlled by adjusting the dc link voltage of the voltage source inverter (VSI) feeding BLDCM. Moreover, a low frequency switching of the VSI is used for electronically commutating the BLDCM for reduced switching losses. The Sheppard-Taylor converter is designed to operate in continuous conduction mode to achieve an improved power quality at the ac mains for a wide range of speed control and supply voltage variation. The BLDCM drive is designed and its performance is simulated in a MATLAB/Simulink environment to achieve the power quality indices within the limits of the international power quality standard IEC-61000-3-2.

Investigation of turbines for driving supersonic compressors II : performance of first configuration with 2.2 percent reduction in nozzle flow area / Warner L. Stewart, Harold J. Schum, Robert Y. Wong

NASA Technical Reports Server (NTRS)

Stewart, Warner L; Schum, Harold J; Wong, Robert Y

1952-01-01

The experimental performance of a modified turbine for driving a supersonic compressor is presented and compared with the performance of the original configuration to illustrate the effect of small changes in the ratio of nozzle-throat area to rotor-throat area. Performance is based on the performance of turbines designed to operate with both blade rows close to choking. On the basis of the results of this investigation, the ratio of areas is concluded to become especially critical in the design of turbines such as those designed to drive high-speed, high-specific weight-flow compressors where the turbine nozzles and rotor are both very close to choking.

Direct-drive inertial confinement fusion research at the Laboratory for Laser Energetics: charting the path to thermonuclear ignition

NASA Astrophysics Data System (ADS)

McCrory, R. L.; Regan, S. P.; Loucks, S. J.; Meyerhofer, D. D.; Skupsky, S.; Betti, R.; Boehly, T. R.; Craxton, R. S.; Collins, T. J. B.; Delettrez, J. A.; Edgell, D.; Epstein, R.; Fletcher, K. A.; Freeman, C.; Frenje, J. A.; Glebov, V. Yu.; Goncharov, V. N.; Harding, D. R.; Igumenshchev, I. V.; Keck, R. L.; Kilkenny, J. D.; Knauer, J. P.; Li, C. K.; Marciante, J.; Marozas, J. A.; Marshall, F. J.; Maximov, A. V.; McKenty, P. W.; Myatt, J.; Padalino, S.; Petrasso, R. D.; Radha, P. B.; Sangster, T. C.; Séguin, F. H.; Seka, W.; Smalyuk, V. A.; Soures, J. M.; Stoeckl, C.; Yaakobi, B.; Zuegel, J. D.

2005-10-01

Significant theoretical and experimental progress continues to be made at the University of Rochester's Laboratory for Laser Energetics (LLE), charting the path to direct-drive inertial confinement fusion (ICF) ignition. Direct drive offers the potential for higher-gain implosions than x-ray drive and is a leading candidate for an inertial fusion energy power plant. LLE's direct-drive ICF ignition target designs for the National Ignition Facility (NIF) are based on hot-spot ignition. A cryogenic target with a spherical DT-ice layer, within or without a foam matrix, enclosed by a thin plastic shell, will be directly irradiated with ~1.5 MJ of laser energy. Cryogenic and plastic/foam (surrogate-cryogenic) targets that are hydrodynamically scaled from these ignition target designs are imploded on the 60-beam, 30 kJ, UV OMEGA laser system to validate the key target physics issues, including energy coupling, hydrodynamic instabilities and implosion symmetry. Prospects for direct-drive ignition on the NIF are extremely favourable, even while it is in its x-ray-drive irradiation configuration, with the development of the polar-direct-drive concept. A high-energy petawatt capability is being constructed at LLE next to the existing 60-beam OMEGA compression facility. This OMEGA EP (extended performance) laser will add two short-pulse, 2.6 kJ beams to the OMEGA laser system to backlight direct-drive ICF implosions and study fast-ignition physics with focused intensities up to 6 × 1020 W cm-2.

"The Heart Game": Using Gamification as Part of a Telerehabilitation Program for Heart Patients.

PubMed

Dithmer, Marcus; Rasmussen, Jack Ord; Grönvall, Erik; Spindler, Helle; Hansen, John; Nielsen, Gitte; Sørensen, Stine Bæk; Dinesen, Birthe

2016-02-01

The aim of this article is to describe the development and testing of a prototype application ("The Heart Game") using gamification principles to assist heart patients in their telerehabilitation process in the Teledialog project. A prototype game was developed via user-driven innovation and tested on 10 patients 48-89 years of age and their relatives for a period of 2 weeks. The application consisted of a series of daily challenges given to the patients and relatives and was based on several gamification principles. A triangulation of data collection techniques (interviews, participant observations, focus group interviews, and workshop) was used. Interviews with three healthcare professionals and 10 patients were carried out over a period of 2 weeks in order to evaluate the use of the prototype. The heart patients reported the application to be a useful tool as a part of their telerehabilitation process in everyday life. Gamification and gameful design principles such as leaderboards, relationships, and achievements engaged the patients and relatives. The inclusion of a close relative in the game motivated the patients to perform rehabilitation activities. "The Heart Game" concept presents a new way to motivate heart patients by using technology as a social and active approach to telerehabilitation. The findings show the potential of using gamification for heart patients as part of a telerehabilitation program. The evaluation indicated that the inclusion of the patient's spouse in the rehabilitation activities could be an effective strategy. A major challenge in using gamification for heart patients is avoiding a sense of defeat while still adjusting the level of difficulty to the individual patient.

Optimization of spent fuel pool weir gate driving mechanism

NASA Astrophysics Data System (ADS)

Liu, Chao; Du, Lin; Tao, Xinlei; Wang, Shijie; Shang, Ertao; Yu, Jianjiang

2018-04-01

Spent fuel pool is crucial facility for fuel storage and nuclear safety, and the spent fuel pool weir gate is the key related equipment. In order to achieve a goal of more efficient driving force transfer, loading during the opening/closing process is analyzed and an optimized calculation method for dimensions of driving mechanism is proposed. The result of optimizing example shows that the method can be applied to weir gates' design with similar driving mechanism.

A driver-adaptive stability control strategy for sport utility vehicles

NASA Astrophysics Data System (ADS)

Zhu, Shenjin; He, Yuping

2017-08-01

Conventional vehicle stability control (VSC) systems are designed for average drivers. For a driver with a good driving skill, the VSC systems may be redundant; for a driver with a poor driving skill, the VSC intervention may be inadequate. To increase safety of sport utility vehicles (SUVs), this paper proposes a novel driver-adaptive VSC (DAVSC) strategy based on scaling the target yaw rate commanded by the driver. The DAVSC system is adaptive to drivers' driving skills. More control effort would be exerted for drivers with poor driving skills, and vice versa. A sliding mode control (SMC)-based differential braking (DB) controller is designed using a three degrees of freedom (DOF) yaw-plane model. An eight DOF nonlinear yaw-roll model is used to simulate the SUV dynamics. Two driver models, namely longitudinal and lateral, are used to 'drive' the virtual SUV. By integrating the virtual SUV, the DB controller, and the driver models, the performance of the DAVSC system is investigated. The simulations demonstrate the effectiveness of the DAVSC strategy.

Driving and Dementia in Older Adults: Implementation and Evaluation of a Continuing Education Project

ERIC Educational Resources Information Center

Meuser, Thomas M.; Carr, David B.; Berg-Weger, Marla; Niewoehner, Pat; Morris, John C.

2006-01-01

Purpose: We aimed to develop and evaluate a multimedia workshop curriculum to educate physicians and other health professionals about (a) driving-related assessment in older adults with dementia, and (b) strategies to encourage driving retirement for impaired individuals. Design and Methods: A curriculum developed by the Older Drivers Project of…

49 CFR 383.51 - Disqualification of drivers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the date the citation was issued, shall not be guilty of this offense. 2 Driving, for the purpose of... drivers. (a) General. (1) A person required to have a CLP or CDL who is disqualified must not drive a CMV... to drive a CMV. (3) A holder of a CLP or CDL is subject to disqualification sanctions designated in...

49 CFR 383.51 - Disqualification of drivers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... citation was issued, shall not be guilty of this offense. 2 Driving, for the purpose of this... drivers. (a) General. (1) A person required to have a CLP or CDL who is disqualified must not drive a CMV... to drive a CMV. (3) A holder of a CLP or CDL is subject to disqualification sanctions designated in...

49 CFR 383.51 - Disqualification of drivers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... citation was issued, shall not be guilty of this offense. 2 Driving, for the purpose of this... drivers. (a) General. (1) A person required to have a CLP or CDL who is disqualified must not drive a CMV... to drive a CMV. (3) A holder of a CLP or CDL is subject to disqualification sanctions designated in...

Reasons Given by Older People for Limitation or Avoidance of Driving

ERIC Educational Resources Information Center

Ragland, David R.; Satariano, William A.; MacLeod, Kara E.

2004-01-01

Purpose: To understand the driving behavior of older adults, this study examines self-reported reasons for driving limitation or avoidance. Design and Methods: Baseline interviews were conducted (n = 2,046) as part of a community-based study of aging and physical performance in persons aged 55 years or older in Sonoma, California. Twenty-one…

Propulsion Electric Grid Simulator (PEGS) for Future Turboelectric Distributed Propulsion Aircraft

NASA Technical Reports Server (NTRS)

Choi, Benjamin B.; Morrison, Carlos; Dever, Timothy; Brown, Gerald V.

2014-01-01

NASA Glenn Research Center, in collaboration with the aerospace industry and academia, has begun the development of technology for a future hybrid-wing body electric airplane with a turboelectric distributed propulsion (TeDP) system. It is essential to design a subscale system to emulate the TeDP power grid, which would enable rapid analysis and demonstration of the proof-of-concept of the TeDP electrical system. This paper describes how small electrical machines with their controllers can emulate all the components in a TeDP power train. The whole system model in Matlab/Simulink was first developed and tested in simulation, and the simulation results showed that system dynamic characteristics could be implemented by using the closed-loop control of the electric motor drive systems. Then we designed a subscale experimental system to emulate the entire power system from the turbine engine to the propulsive fans. Firstly, we built a system to emulate a gas turbine engine driving a generator, consisting of two permanent magnet (PM) motors with brushless motor drives, coupled by a shaft. We programmed the first motor and its drive to mimic the speed-torque characteristic of the gas turbine engine, while the second motor and drive act as a generator and produce a torque load on the first motor. Secondly, we built another system of two PM motors and drives to emulate a motor driving a propulsive fan. We programmed the first motor and drive to emulate a wound-rotor synchronous motor. The propulsive fan was emulated by implementing fan maps and flight conditions into the fourth motor and drive, which produce a torque load on the driving motor. The stator of each PM motor is designed to travel axially to change the coupling between rotor and stator. This feature allows the PM motor to more closely emulate a wound-rotor synchronous machine. These techniques can convert the plain motor system into a unique TeDP power grid emulator that enables real-time simulation performance using hardware-in-the-loop (HIL).

Energy efficient engine: Preliminary design and integration studies

NASA Technical Reports Server (NTRS)

Johnston, R. P.; Hirschkron, R.; Koch, C. C.; Neitzel, R. E.; Vinson, P. W.

1978-01-01

Parametric design and mission evaluations of advanced turbofan configurations were conducted for future transport aircraft application. Economics, environmental suitability and fuel efficiency were investigated and compared with goals set by NASA. Of the candidate engines which included mixed- and separate-flow, direct-drive and geared configurations, an advanced mixed-flow direct-drive configuration was selected for further design and evaluation. All goals were judged to have been met except the acoustic goal. Also conducted was a performance risk analysis and a preliminary aerodynamic design of the 10 stage 23:1 pressure ratio compressor used in the study engines.

Improved data retrieval from TreeBASE via taxonomic and linguistic data enrichment

PubMed Central

Anwar, Nadia; Hunt, Ela

2009-01-01

Background TreeBASE, the only data repository for phylogenetic studies, is not being used effectively since it does not meet the taxonomic data retrieval requirements of the systematics community. We show, through an examination of the queries performed on TreeBASE, that data retrieval using taxon names is unsatisfactory. Results We report on a new wrapper supporting taxon queries on TreeBASE by utilising a Taxonomy and Classification Database (TCl-Db) we created. TCl-Db holds merged and consolidated taxonomic names from multiple data sources and can be used to translate hierarchical, vernacular and synonym queries into specific query terms in TreeBASE. The query expansion supported by TCl-Db shows very significant information retrieval quality improvement. The wrapper can be accessed at the URL The methodology we developed is scalable and can be applied to new data, as those become available in the future. Conclusion Significantly improved data retrieval quality is shown for all queries, and additional flexibility is achieved via user-driven taxonomy selection. PMID:19426482

Integrating Socioeconomic and Earth Science Data Using Geobrowsers and Web Services: A Demonstration

NASA Astrophysics Data System (ADS)

Schumacher, J. A.; Yetman, G. G.

2007-12-01

The societal benefit areas identified as the focus for the Global Earth Observing System of Systems (GEOSS) 10- year implementation plan are an indicator of the importance of integrating socioeconomic data with earth science data to support decision makers. To aid this integration, CIESIN is delivering its global and U.S. demographic data to commercial and open source Geobrowsers and providing open standards based services for data access. Currently, data on population distribution, poverty, and detailed census data for the U.S. are available for visualization and access in Google Earth, NASA World Wind, and a browser-based 2-dimensional mapping client. The mapping client allows for the creation of web map documents that pull together layers from distributed servers and can be saved and shared. Visualization tools with Geobrowsers, user-driven map creation and sharing via browser-based clients, and a prototype for characterizing populations at risk to predicted precipitation deficits will be demonstrated.

Using Citygml to Deploy Smart-City Services for Urban Ecosystems

NASA Astrophysics Data System (ADS)

Prandi, F.; De Amicis, R.; Piffer, S.; Soave, M.; Cadzow, S.; Gonzalez Boix, E.; D'Hont, E.

2013-05-01

The rapid technological evolution, which is characterizing all the disciplines involved within the wide concept of smart cities, becomes a key factor to trigger true user-driven innovation. In this context 3D city models will play an increasingly important role in our daily lives and become an essential part of the modern city information infrastructure (Spatial Data Infrastructure). The goal of this paper is to introduce the i-SCOPE (interoperable Smart City services through an Open Platform for urban Ecosystems) project methodology and implementations together with key technologies and open standards. Based on interoperable 3D CityGML UIMs, the aim of i-Scope is to deliver an open platform on top of which it possible to develop, within different domains, various "smart city" services. Moreover, in i-SCOPE different issues, transcending the mere technological domain, are being tackled, including aspects dealing with social and environmental issues. Indeed several tasks including citizen awareness, crowd source and voluntary based data collection as well as privacy issue concerning involved people should be considered.

Progressive Learning of Topic Modeling Parameters: A Visual Analytics Framework.

PubMed

El-Assady, Mennatallah; Sevastjanova, Rita; Sperrle, Fabian; Keim, Daniel; Collins, Christopher

2018-01-01

Topic modeling algorithms are widely used to analyze the thematic composition of text corpora but remain difficult to interpret and adjust. Addressing these limitations, we present a modular visual analytics framework, tackling the understandability and adaptability of topic models through a user-driven reinforcement learning process which does not require a deep understanding of the underlying topic modeling algorithms. Given a document corpus, our approach initializes two algorithm configurations based on a parameter space analysis that enhances document separability. We abstract the model complexity in an interactive visual workspace for exploring the automatic matching results of two models, investigating topic summaries, analyzing parameter distributions, and reviewing documents. The main contribution of our work is an iterative decision-making technique in which users provide a document-based relevance feedback that allows the framework to converge to a user-endorsed topic distribution. We also report feedback from a two-stage study which shows that our technique results in topic model quality improvements on two independent measures.

Manual transmission enhances attention and driving performance of ADHD adolescent males: pilot study.

PubMed

Cox, Daniel J; Punja, Mohan; Powers, Katie; Merkel, R Lawrence; Burket, Roger; Moore, Melissa; Thorndike, Frances; Kovatchev, Boris

2006-11-01

Inattention is a major contributor to driving mishaps and is especially problematic among adolescent drivers with ADHD, possibly contributing to their 2 to 4 times higher incidence of collisions. Manual transmission has been demonstrated to be associated with greater arousal. This study tests the hypotheses that manual transmission, compared to automatic transmission, would be associated with better attention and performance on a driving simulator. Ten adolescent drivers with ADHD practice driving on the simulator in the manual and automatic mode. Employing a single-blind, cross-over design, participants drive the simulator at 19:30 and 22:30 hr for 30 min in both transmissions and rate their attention to driving. Subjectively, participants report being more attentive while driving in manual transmission mode. Objectively, participants drive safer in the manual transmission mode. Although in need of replication, this pilot study suggests a behavioral intervention to improve driving performance among ADHD adolescents.

Magnetically coupled gear based drive mechanism for contactless continuous rotation using superconducting magnetic bearing below 10 K

NASA Astrophysics Data System (ADS)

Matsumura, T.; Sakurai, Y.; Kataza, H.; Utsunomiya, S.; Yamamoto, R.

2016-11-01

We present the design and mechanical performances of a magnetically coupled gear mechanism to drive a levitating rotor magnet of a superconducting magnetic bearing (SMB). The SMB consists of a ring-shaped high-temperature superconducting array (YBCO) and a ring-shaped permanent magnet. This rotational system is designed to operate below 10 K, and thus the design philosophy is to minimize any potential source of heat dissipation. While an SMB provides only a functionality of namely a bearing, it requires a mechanism to drive a rotational motion. We introduce a simple implementation of a magnetically coupled gears between a stator and a rotor. This enables to achieve enough torque to drive a levitating rotor without slip at the rotation frequency of about 1 Hz below 10 K. The rotational variation between the rotor and the drive gear is synchronised within σ = 0.019 Hz. The development of this mechanism is a part of the program to develop a testbed in order to evaluate a prototype half-wave plate based polarization modulator for future space missions. The successful development allows this modulator to be a candidate for an instrument to probe the cosmic inflation by measuring the cosmic microwave background polarization.

Safety reliability evaluation when vehicles turn right from urban major roads onto minor ones based on driver's visual perception.

PubMed

Yu, Bo; Chen, Yuren; Wang, Ruiyun; Dong, Yongjie

2016-10-01

Turning right has a significant impact on urban road traffic safety. Driving into the curve inappropriately or with improper turning speed often leads to a series of potential accidents and hidden dangers. For a long time, the design speed at intersections has been used to determine the physical radius of curbs and channelization, and drivers are expected to drive in accordance with the design speed. However, a large number of real vehicle tests show that for the road without an exclusive right-turn lane, there is not a good correlation between the physical radius of curbs and the turning right speeds. In this paper, shape parameters of the driver's visual lane model are put forward and they have relatively high correlations with right-turn speeds. Hence, an evaluation method about safety reliability of turning right from urban major roads onto minor ones based on driver's visual perception is proposed. For existing roads, the evaluation object could be real driving videos; for those under construction roads, the evaluation object could be visual scenes obtained from a driving simulation device. Findings in this research will make a contribution to the optimization of right-turn design at intersections and lead to the development of auxiliary driving technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modal Analysis Using the Singular Value Decomposition and Rational Fraction Polynomials

DTIC Science & Technology

2017-04-06

information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and...results. The programs are designed for experimental datasets with multiple drive and response points and have proven effective even for systems with... designed for experimental datasets with multiple drive and response points and have proven effective even for systems with numerous closely-spaced

Voltage directive drive with claw pole motor and control without rotor position indicator

NASA Astrophysics Data System (ADS)

Stroenisch, Volker Ewald

Design and testing of a voltage directive drive for synchronous variable speed claw pole motor and control without rotor position indicator is described. Economic analysis of the designed regulation is performed. Computations of stationary and dynamic behavior are given and experimental operational behavior is determined. The motors can be used for electric transportation vehicles, diesel motors, and electric railway engines.

Miniature rotary actuator

NASA Technical Reports Server (NTRS)

Fink, R. A.; Ellis, R. C.

1996-01-01

The trend toward smaller satellites has challenged component manufacturers to reduce the size, weight, and cost of their products while maintaining high performance. Both a new stepper motor and a new harmonic drive were developed to meet this need. The resulting actuator embodies small angle stepper technology usually reserved for larger units and incorporates an integral approach to harmonic drive design. By product simplifications, costs were significantly reduced over prior designs.

Design and performance of heart assist or artificial heart control systems

NASA Technical Reports Server (NTRS)

Webb, J. A., Jr.; Gebben, V. D.

1978-01-01

The factors leading to the design of a controlled driving system for either a heart assist pump or artificial heart are discussed. The system provides square pressure waveform to drive a pneumatic-type blood pump. For assist usage the system uses an R-wave detector circuit that can detect the R-wave of the electrocardiogram in the presence of electrical disturbances. This circuit provides a signal useful for synchronizing an assist pump with the natural heart. It synchronizes a square wave circuit, the output of which is converted into square waveforms of pneumatic pressure suitable for driving both assist device and artificial heart. The pressure levels of the driving waveforms are controlled by means of feedback channels to maintain physiological regulation of the artificial heart's output flow. A more compact system that could achieve similar regulatory characteristics is also discussed.

Analysis on design and performance of a solar rotary house

NASA Astrophysics Data System (ADS)

Fan, Xuhong; Zhang, Zhaochang; Yang, Fan; Cao, Lilin; Xu, Jing; Yuan, Mingyang

2017-04-01

A solar rotary house is designed, composed of rotating main structure, fixed cylinder, rotating drive system, solar photovoltaic system and so on, to achieve 360° rotation. Thus it can change the dark and humid situation of the traditional fixed house shade. Its bearing capacity, driving force and safety are analyzed. Rotary driving force and living energy are provided by solar photovoltaic system on roofs and walls. The Phonenics, Ecotect simulation analysis conclude that the rotating house indoor has better natural ventilation effect, more uniform lighting, better the sunshine time compared with traditional houses, becoming a green, energy-saving, comfortable building model.

Sensorless sliding mode observer for a five-phase permanent magnet synchronous motor drive.

PubMed

Hosseyni, Anissa; Trabelsi, Ramzi; Mimouni, Med Faouzi; Iqbal, Atif; Alammari, Rashid

2015-09-01

This paper deals with the sensorless vector controlled five-phase permanent magnet synchronous motor (PMSM) drive based on a sliding mode observer (SMO). The observer is designed considering the back electromotive force (EMF) of five-phase permanent magnet synchronous motor. The SMO structure and design are illustrated. Stability of the proposed observer is demonstrated using Lyapunov stability criteria. The proposed strategy is asymptotically stable in the context of Lyapunov theory. Simulated results on a five-phase PMSM drive are displayed to validate the feasibility and the effectiveness of the proposed control strategy. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Features of the solar array drive mechanism for the space telescope

NASA Technical Reports Server (NTRS)

Hostenkamp, R. G.

1985-01-01

The solar array drive mechanism for the Space Telescope embodies several features not customarily found on solar array drives. Power and signal transfer is achieved by means of a flexible wire harness for which the chosen solution, consisting of 168 standard wires, is described. The torque performance data of the harness over its temperature range are presented. The off load system which protects the bearings from the launch loads is released by a trigger made from Nitinol, the memory alloy. The benefits of memory alloy and the caveats for the design are briefly discussed. The design of the off load system is described and test experience is reported.

Design and implementation of fast bipolar clock drivers for CCD imaging systems in space applications

NASA Astrophysics Data System (ADS)

Jayarajan, Jayesh; Kumar, Nishant; Verma, Amarnath; Thaker, Ramkrishna

2016-05-01

Drive electronics for generating fast, bipolar clocks, which can drive capacitive loads of the order of 5-10nF are indispensable for present day Charge Coupled Devices (CCDs). Design of these high speed bipolar clocks is challenging because of the capacitive loads that have to be driven and a strict constraint on the rise and fall times. Designing drive electronics circuits for space applications becomes even more challenging due to limited number of available discrete devices, which can survive in the harsh radiation prone space environment. This paper presents the design, simulations and test results of a set of such high speed, bipolar clock drivers. The design has been tested under a thermal cycle of -15 deg C to +55 deg C under vacuum conditions and has been designed using radiation hardened components. The test results show that the design meets the stringent rise/fall time requirements of 50+/-10ns for Multiple Vertical CCD (VCCD) clocks and 20+/-5ns for Horizontal CCD (HCCD) clocks with sufficient design margins across full temperature range, with a pixel readout rate of 6.6MHz. The full design has been realized in flexi-rigid PCB with package volume of 140x160x50 mm3.

Measurements and Calculations of Halfraum Radiation Drives at the Omega Laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacLaren, S A; Back, C A; Hammer, J H

2005-01-06

Thin walled gold halfraums are a common choice for producing x-ray drives in experiments at high-power laser facilities. At the Omega Laser, we use 10 kJ of laser energy in a two-pulse sequence to generate halfraum drive temperatures of 160-190 eV for {approx}3ns. This type of drive is well characterized and reproducible, with characterization of the drive radiation temperature typically performed using the Dante diagnostic. Additionally, calibrated Photoconductive Diamond Detectors (PCDs) are used to measure the drive when it is desirable to utilize the Dante elsewhere in the experiment. Measurements of halfraum drives from both Dante and PCDs are comparedmore » with calculations, with good agreement. This agreement lends the calculations a predictive capability in designing further experiments utilizing halfraum drives.« less

Improving Motor and Drive System Performance – A Sourcebook for Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This sourcebook outlines opportunities to improve motor and drive systems performance. The sourcebook is divided into four main sections: (1) Motor and Drive System Basics: Summarizes important terms, relationships, and system design considerations relating to motor and drive systems. (2) Performance Opportunity Road Map: Details the key components of well-functioning motor and drive systems and opportunities for energy performance opportunities. (3) Motor System Economics: Offers recommendations on how to propose improvement projects based on corporate priorities, efficiency gains, and financial payback periods. (4) Where to Find Help: Provides a directory of organizations associated with motors and drives, as well asmore » resources for additional information, tools, software, videos, and training opportunities.« less

A compact optical fiber positioner

NASA Astrophysics Data System (ADS)

Hu, Hongzhuan; Wang, Jianping; Liu, Zhigang; Zhou, Zengxiang; Zhai, Chao; Chu, Jiaru

2016-07-01

In this paper, a compact optical fiber positioner is proposed, which is especially suitable for small scale and high density optical fiber positioning. Based on the positioning principle of double rotation, positioner's center shaft depends on planetary gear drive principle, meshing with the fixed annular gear central motor gear driving device to rotate, and the eccentric shaft rotated driving by a coaxial eccentric motor, both center and the eccentric shaft are supported by a rolling bearings; center and eccentric shaft are both designed with electrical zero as a reference point, and both of them have position-limiting capability to ensure the safety of fiber positioning; both eccentric and center shaft are designed to eliminating clearance with spring structure, and can eliminate the influence of gear gap; both eccentric and center motor and their driving circuit can be installed in the positioner's body, and a favorable heat sink have designed, the heat bring by positioning operation can be effectively transmit to design a focal plane unit through the aluminum component, on sleeve cooling spiral airway have designed, when positioning, the cooling air flow is inlet into install hole on the focal plate, the cooling air flow can effectively take away the positioning's heat, to eliminate the impact of the focus seeing. By measuring position device's sample results show that: the unit accuracy reached 0.01mm, can meet the needs of fiber positioning.

Mechanical Design Engineering Enabler Project wheel and wheel drives

NASA Technical Reports Server (NTRS)

Nutt, Richard E.; Couch, Britt K.; Holley, John L., Jr.; Garris, Eric S.; Staut, Paul V.

1992-01-01

Our group was assigned the responsibility of designing the wheel and wheel drive system for a proof-of-concept model of the lunar-based ENABLER. ENABLER is a multi-purpose, six wheeled vehicle designed to lift and transport heavy objects associated with the construction of a lunar base. The resulting design was based on the performance criteria of the ENABLER. The drive system was designed to enable the vehicle to achieve a speed of 7 mph on a level surface, climb a 30 percent grade, and surpass a one meter high object and one meter wide crevice. The wheel assemblies were designed to support the entire weight of the vehicle on two wheels. The wheels were designed to serve as the main component of the vehicle's suspension and will provide suitable traction for lunar-type surfaces. The expected performance of the drive system for the ENABLER was influenced by many mechanical factors. The expected top speed on a level sandy surface is 4 mph instead of the desired 7 mph. This is due to a lack of necessary power at the wheels. The lack of power resulted from dimension considerations that allowed only an eight horsepower engine and also from mechanical inefficiencies of the hydraulic system. However, the vehicle will be able to climb a 30 percent grade, surpass a one meter high object and one meter wide crevice. The wheel assemblies will be able to support the entire weight of the vehicle on two wheels. The wheels will also provide adequate suspension for the vehicle and sufficient traction for lunar-type surfaces.

Complete Development and Implement AFIT/ENG Database Management System. Volume 1.

DTIC Science & Technology

1984-12-01

graphic depiction of the sys - ten specification that identifies inputs, desired outputs, and data transformations. This usually leads to the definition and...DATA-SET-NAME-TLME DRIVE=01,5000,DUI DATA-SET-NAME=BLRM DRIVE=02,5000, DUI DATA-SET- NAbE =CPTY DRIVE=03,5000 ,DUI L-1 DATA-SET-NAME=DAYS DRIVE=-04...DEC), the Form Manageent Sys - tern (FMS). It is designed for ease of formulation and form simulation in order to collect and transmit data in an

Design and characterization of piezoelectric ultrasonic motors

NASA Astrophysics Data System (ADS)

Yener, Serra

This thesis presents modeling and prototype fabrication and characterization of new types of piezoelectric ultrasonic micromotors. Our approach in designing these piezoelectric motors was: (i) to simplify the structure including the poling configuration of piezoelectric elements used in the stator and (ii) to reduce the number of components in order to decrease the cost and enhance the driving reliability. There are two different types of piezoelectric motors designed throughout this research. The first of these designs consists of a metal tube, on which two piezoelectric ceramic plates poled in thickness direction, were bonded. Two orthogonal bending modes of the hollow cylinder were superimposed resulting in a rotational vibration. Since the structure and poling configuration of the active piezoelectric elements used in the stator are simple, this motor structure is very suitable for miniaturization. Moreover, a single driving source can excite two bending modes at the same time, thus generate a wobble motion. Three types of prototypes are included in this design. The piezoelectric stator structure is the same for all. However, the dimensions of the motors are reduced by almost 50 percent. Starting with a 10 mm long stator, we reached to 4 mm in the last prototype. The initial diameter was 2.4 mm, which was reduced to 1.6 mm. In the final design, the rotor part of the motor was changed resulting in the reduction in the number of components. In terms of driving circuit, a single driving source was enough to run the motors and a conventional switching power supply type resonant L-C circuit was used. A simple motor structure with a simple driving circuit were combined successfully and fabricated inexpensively. The second design is a shear type piezoelectric linear motor. The behavior of a single rectangular piezoelectric shear plate was analyzed and after optimizing the dimensions and the mode characteristics, a prototype was fabricated. The prototype consists of one layer of ceramic and a brass teeth-like layer bonded on it. The displacement was amplified with the metal layer, the teeth of which were placed on the points of in-phase motion. The targeted application area is paper-feeding mechanism. In terms of application areas for the first design, a gas valve system and a micro vehicle were constructed. In addition, a new optical coherence tomography endoscope by utilizing the piezoelectric micromotor was designed. Finally, the prototype motor was integrated inside the camera of a cell phone to drive the zoom mechanism.

Driving habits and risk exposure in older drivers: lessons learned from the implementation of a self-regulation curriculum.

PubMed

Jones, Vanya C; Cho, Juhee; Abendschoen-Milani, Jackie; Gielen, Andrea

2011-10-01

This article describes the development and pilot testing of Seniors on the MOVE (Mature Operators Vehicular Education), a safe driving education program for older adults. The study aims are to describe driving experiences and habits of a community sample of older drivers and to determine whether the program reduces their driving risk exposures. A 2-group randomized design was used. Fifty-eight participants with an average age of 70 were randomly assigned to the MOVE program or a no treatment control group. MOVE is a 4-session program designed to help older drivers better understand and utilize self-regulation skills for safer driving. Baseline and 4-week follow-up questionnaires were completed by both groups, after which the control group received the MOVE program. In the total sample, 14 percent reported having ever been in a traffic crash where someone was injured, and 10 percent reported having received a traffic citation in the past 6 months. Almost one half of the sample (47%) reported thinking about reducing the amount of driving done at night. Nearly one third were thinking about reducing the amount of driving done in unfamiliar places (32%) and the number of miles driven each week (30%). Participants reported most frequently driving between 2 to 10 miles from home, on local roadways, and between 9:00 am and 4:00 pm. Based on responses to items that measured such driving habits, a risk exposure score was created by combining driving exposure variables. Participants were categorized into lower and higher driving risk exposure groups at baseline and follow-up. There were no statistical differences in changes in higher or lower risk driving exposure variables when comparing the 2 groups. Although the impact of this program on reported driving behaviors yielded null results, descriptions of older drivers' habits and plans are informative. Because many participants were thinking about making changes to their driving habits, and many already had, the need for more effective self-regulation driving safety programs to help with this process is clear.

49 CFR 383.51 - Disqualification of drivers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... drivers. (a) General. (1) A person required to have a CLP or CDL who is disqualified must not drive a CMV... to drive a CMV. (3) A holder of a CLP or CDL is subject to disqualification sanctions designated in paragraphs (b) and (c) of this section, if the holder drives a CMV or non-CMV and is convicted of the...

Common drive unit

NASA Technical Reports Server (NTRS)

Ellis, R. C.; Fink, R. A.; Moore, E. A.

1987-01-01

The Common Drive Unit (CDU) is a high reliability rotary actuator with many versatile applications in mechanism designs. The CDU incorporates a set of redundant motor-brake assemblies driving a single output shaft through differential. Tachometers provide speed information in the AC version. Operation of both motors, as compared to the operation of one motor, will yield the same output torque with twice the output speed.

The Effects of Fatal Vision Goggles on Drinking and Driving Intentions in College Students

ERIC Educational Resources Information Center

Hennessy, Dwight A.; Lanni-Manley, Elizabeth; Maiorana, Nicole

2006-01-01

The present study was designed to examine the effectiveness of Fatal Vision Goggles in reducing intentions to drink and drive. Participants performed a field sobriety task and drove in a traffic simulator while wearing the goggles. A regression analysis was performed in order to predict changes in intentions to drink and drive, using typical…

One Approach to the Synthesis, Design and Manufacture of Hyperboloid Gear Sets With Face Mating Gears. Part 1: Basic Theoretical and Cad Experience

NASA Astrophysics Data System (ADS)

Abadjiev, Valentin; Abadjieva, Emilia

2016-06-01

Hyperboloid gear drives with face mating gears are used to transform rotations between shafts with non-parallel and non-intersecting axes. A special case of these transmissions are Spiroid and Helicon gear drives. The classical gear drives of this type are the Archimedean ones. The objective of this study are hyperboloid gear drives with face meshing, when the pinion possesses threads of conic convolute, Archimedean and involute types, or the pinion has threads of cylindrical convolute, Archimedean and involute types. For simplicity, all three types transmis- sions with face mating gears and a conic pinion are titled Spiroid and all three types transmissions with face mating gears and a cylindrical pinion are titled Helicon. Principles of the mathematical modelling of tooth contact synthesis are discussed in this study. The presented research shows that the synthesis is realized by application of two mathematical models: pitch contact point and mesh region models. Two approaches for synthesis of the gear drives in accordance with Olivier's principles are illustrated. The algorithms and computer programs for optimization synthesis and design of the studied hyperboloid gear drives are presented.

Bus Driver Training Simulator Assessment

DOT National Transportation Integrated Search

1980-01-01

Simulation has become an increasingly important tool in driving research, highway research, and vehicle design. This report documents the results of an investigation into the feasibility of developing a driving simulator as a means of teaching safe d...

Potential Energy and Emission Benefits of Vehicle Automation and Connectivity

DOT National Transportation Integrated Search

2017-08-01

Driving behavior greatly impacts vehicle tailpipe emissions. Connected and automated vehicle (CAV) technologies are designed to smooth driving and relieve traffic congestion and are therefore expected to reduce fuel consumption and tailpipe emissions...

A Guide to Sentencing DUI Offenders

DOT National Transportation Integrated Search

1996-03-01

This sentencing guide is designed to assist judges and prosecutors in reducing recidivism among people convicted of drinking and driving offenses. Today's driving under the influence (DUI) arrestee is often a repeat offender and resistant to deterren...

Design and analysis of the Gemini chain system in dual clutch transmission of automobile

NASA Astrophysics Data System (ADS)

Cheng, Yabing; Guo, Haitao; Fu, Zhenming; Wan, Nen; Li, Lei; Wang, Yang

2015-01-01

Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load. Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, analysis, and noise characteristics of the chain drive system are weak. System design and noise characteristic are studied for a new type Gemini chain of dual-clutch automatic transmission. Based on the meshing theory of silent chain, the design parameters of the Gemini chain system are calculated and the mathematical models and dynamic analysis models of the Gemini chain system are established. Dynamic characteristics of the Gemini chain system is simulated and the contact force of plate and pin, plate and sprockets, the chain tension forces, the transmission error and the stress of plates and pins are analyzed. According to the simulation results of the Gemini chain system, the noise experiment about system is carried out. The noise values are tested at different speed and load and spectral characteristics are analyzed. The results of simulation and experimental show that the contact forces of plate and pin, plate and sprockets are smaller than the allowable stress values, the chain tension force is less than ultimate tension and transmission error is limited in 1.2%. The noise values can meet the requirements of industrial design, and it is proved that the design and analysis method of the Gemini chain system is scientific and feasible. The design and test system is built from analysis to test of Gemini chain system. This research presented will provide a corresponding theoretical guidance for the design and dynamic characteristics and noise characteristics of chain drive system.

Fuzzy Inference Based Obstacle Avoidance Control of Electric Powered Wheelchair Considering Driving Risk

NASA Astrophysics Data System (ADS)

Kiso, Atsushi; Murakami, Hiroki; Seki, Hirokazu

This paper describes a novel obstacle avoidance control scheme of electric powered wheelchairs for realizing the safe driving in various environments. The “electric powered wheelchair” which generates the driving force by electric motors is expected to be widely used as a mobility support system for elderly people and disabled people; however, the driving performance must be further improved because the number of driving accidents caused by elderly operator's narrow sight and joystick operation errors is increasing. This paper proposes a novel obstacle avoidance control scheme based on fuzzy algorithm to prevent driving accidents. The proposed control system determines the driving direction by fuzzy algorithm based on the information of the joystick operation and distance to obstacles measured by ultrasonic sensors. Fuzzy rules to determine the driving direction are designed surely to avoid passers-by and walls considering the human's intent and driving environments. Some driving experiments on the practical situations show the effectiveness of the proposed control system.

Steering Clear of Driving After Drinking: a Tailored e-Health Intervention for Reducing Repeat Offending and Modifying Alcohol Use in a High-Risk Cohort.

PubMed

Wilson, Hollie Jai; Palk, Gavan; Sheehan, Mary Christina; Wishart, Darren; Watson, Barry

2017-10-01

Digital interventions to reduce risk behaviours are emerging as effective public health measures; however, few have been applied to drink driving and associated alcohol use based on a harm reduction perspective. This paper reports on the design, development, and pilot of a novel intervention which aims to reduce repeat offending by first-time convicted drink driving offenders. It explores whether an online program is acceptable and user friendly and contains useful and relevant content, with a sample of first-time drink driving offenders recruited at the time of conviction. Building upon existing research into interventions to reduce drink driving recidivism and problem alcohol use, a tailored program was designed to provide content specifically concerned with drink driving and with an additional component related to alcohol use. Following stakeholder and internal review, the 'Steering Clear First Offender Drink Driving Program' was subsequently piloted with 15 first-time drink driving offenders. Evaluative data was analysed both quantitatively and qualitatively. The pilot results indicate that the participants found the program to be user friendly, as demonstrated by high scores in relation to navigation, online delivery, engagement, avatar usage and straightforwardness. They reported that they found the content to be useful and relevant and that the key learning area was in relation to the consequences of drink driving. Online interventions for reducing risky behaviour such as drink driving may be useful and cost effective from a public health perspective. Potentially, they can directly address risky behaviours associated with alcohol use in high-risk cohorts that may not ordinarily receive intervention.

[Fitness to drive in dementia - theoretical framing and design of a recommendation for German general practice].

PubMed

Pentzek, Michael; Michel, Jacqueline Verena; Ufert, Marie; Vollmar, Horst Christian; Wilm, Stefan; Leve, Verena

2015-01-01

General practitioners (GPs) are among the first to be contacted by persons with dementia and their relatives. Fitness to drive in dementia is a subject of uncertainty and conflict for GPs. Development of recommendations for German general practice on managing fitness to drive in dementia. Specification of problem areas by using relevant parts of a metasynthesis of international qualitative dementia research with GPs; literature review on evidence regarding the pre-defined problem areas; deduction of a preliminary design for a recommendation in a multi-professional team. The difficulties include the assessment of fitness to drive in the office setting, concerns about damaging the patient-physician relationship by raising the issue of driving fitness, and uncertainties about the GP's own legal role. A diagnosis of dementia does not per se preclude driving. The majority of elderly people would accept discussing fitness to drive with their GP. In Germany, GPs are not obliged to assess fitness to drive, or to report unsafe drivers to the Licensing Agency, but under certain conditions they do have the right to report. Addressing the issue of driving and dementia early with the patient seems to be a prerequisite for a resource-oriented and patient-centred management. The distinction between medical, ethical-communicative, and legal aspects enabled us to break down this complex problem and thus provide the informative basis to draft tailored recommendations. In an ongoing project, this framework will be further developed and informed by the expertise of patients, family caregivers, and professionals from various fields. Copyright © 2015. Published by Elsevier GmbH.

Design and simulation of bi-directional microfluid driving systems

NASA Astrophysics Data System (ADS)

Jen, Chun-Ping; Lin, Yu-Cheng

2002-03-01

Micro total analysis systems (μTAS) have been developed to perform a number of analytical processes involving chemical reactions, separation and sensing on a single chip. In medical and biomedical applications, μTAS must be designed considering special transport mechanisms to move samples and reagents through the microchannels in the system. For conventional micropumps, however, complicated relationships exist between the pumping mechanisms, the conditions under which the devices operate and the behavior of the multi-component fluids transported in these channels. A bi-directional microfluid driving system has been developed in this paper. This pneumatic system is an on-chip planar structure with no moving parts and does not require microfabricated heaters or electrodes. The pumping actuation is introduced to the microchannel fabricated in the chip by blowing an airflow through this device. The bi-directional driving module combines two individual components for suction and exclusion. The driving system provides a stable and flexible bi-directional microfluid driving control. The tunable parameters for adjusting the exclusion/suction ratios, such as the location of the inlet channel and the velocities of the airflow, have been observed in the numerical study. The optimal exclusion/suction ratio for the specific purpose of the driving system can be selected by changing the location of the microchannel to the reaction area for the sample/reagent. The velocity at the microchannel can be adjusted by varying the inlet velocities for the suction and exclusion components. For the presented design, no air conduit was employed to connect the servo-system to the driving system; therefore the packaging difficulty and leakage problem, which may arise in conventional systems, can be eliminated. The final airflow outlet was fixed in one direction so that it can prevent cross-contamination between the servo-system and the chip. The driving system is therefore particularly suited to microdevices for biochemical analysis.

Biological, Psychological, and Sociocultural Factors Contributing to the Drive for Muscularity in Weight-Training Men

PubMed Central

Schneider, Catharina; Rollitz, Laura; Voracek, Martin; Hennig-Fast, Kristina

2016-01-01

The drive for muscularity and associated behaviors (e.g., exercising and dieting) are of growing importance for men in Western societies. In its extreme form, it can lead to body image concerns and harmful behaviors like over-exercising and the misuse of performance-enhancing substances. Therefore, investigating factors associated with the drive for muscularity, especially in vulnerable populations like bodybuilders and weight trainers can help identify potential risk and protective factors for body image problems. Using a biopsychosocial framework, the aim of the current study was to explore different factors associated with drive for muscularity in weight-training men. To this purpose, German-speaking male weight trainers (N = 248) completed an online survey to determine the extent to which biological, psychological, and sociocultural factors contribute to drive for muscularity and its related attitudes and behaviors. Using multiple regression models, findings showed that media ideal body internalization was the strongest positive predictor for drive for muscularity, while age (M = 25.9, SD = 7.4) held the strongest negative association with drive for muscularity. Dissatisfaction with muscularity, but not with body fat, was related to drive for muscularity. The fat-free mass index, a quantification of the actual degree of muscularity of a person, significantly predicted drive for muscularity-related behavior but not attitudes. Body-related aspects of self-esteem, but not global self-esteem, were significant negative predictors of drive for muscularity. Since internalization of media body ideals presented the highest predictive value for drive for muscularity, these findings suggest that media body ideal internalizations may be a risk factor for body image concerns in men, leading, in its most extreme form to disordered eating or muscle dysmorphia. Future research should investigate the relations between drive for muscularity, age, body composition, internalization, dissatisfaction with muscularity and body-related self-esteem using longitudinal study designs. Limitations concern the cross-sectional design of the study, self-reported body composition measures and the homogeneity of the sample. PMID:28066308

Computer Tensor Codes to Design the War Drive

NASA Astrophysics Data System (ADS)

Maccone, C.

To address problems in Breakthrough Propulsion Physics (BPP) and design the Warp Drive one needs sheer computing capabilities. This is because General Relativity (GR) and Quantum Field Theory (QFT) are so mathematically sophisticated that the amount of analytical calculations is prohibitive and one can hardly do all of them by hand. In this paper we make a comparative review of the main tensor calculus capabilities of the three most advanced and commercially available “symbolic manipulator” codes. We also point out that currently one faces such a variety of different conventions in tensor calculus that it is difficult or impossible to compare results obtained by different scholars in GR and QFT. Mathematical physicists, experimental physicists and engineers have each their own way of customizing tensors, especially by using different metric signatures, different metric determinant signs, different definitions of the basic Riemann and Ricci tensors, and by adopting different systems of physical units. This chaos greatly hampers progress toward the design of the Warp Drive. It is thus suggested that NASA would be a suitable organization to establish standards in symbolic tensor calculus and anyone working in BPP should adopt these standards. Alternatively other institutions, like CERN in Europe, might consider the challenge of starting the preliminary implementation of a Universal Tensor Code to design the Warp Drive.

Determining Acceptable Limits of Fast-Electron Preheat in Polar-Drive-Ignition Designs

NASA Astrophysics Data System (ADS)

Delettrez, J. A.; Collins, T. J. B.; Ye, C.

2014-10-01

In direct-drive-ignition designs, preheat by fast electrons created by the two-plasmon-decay instability at the quarter-critical density surface can increase the adiabat in the fuel layer and prevent ignition. Since eliminating the preheat entirely is not possible, it is necessary to understand the levels of preheat our targets can withstand before ignition is precluded. The current polar-drive point design is used as the basis for examining the effects of increasing the levels of fast electrons using the one-dimensional, radiation-hydrodynamics code LILAC. Once ignition failure is obtained, the design is then reoptimized using Telios, a downhill simplex method program, to recover ignition. This cycle is repeated until the design can no longer be reoptimized to produce ignition. Mappings of these final results provide insight into ignition failure caused by preheat and what specific target parameters serve to best stave off the effects of the preheat. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

A calibration mechanism based on worm drive for space telescope

NASA Astrophysics Data System (ADS)

Chong, Yaqin; Li, Chuang; Xia, Siyu; Zhong, Peifeng; Lei, Wang

2017-08-01

In this paper, a new type of calibration mechanism based on worm drive is presented for a space telescope. This calibration mechanism based on worm drive has the advantages of compact size and self-lock. The mechanism mainly consists of thirty-six LEDs as the light source for flat calibration, a diffuse plate, a step motor, a worm gear reducer and a potentiometer. As the main part of the diffuse plate, a PTFE tablet is mounted in an aluminum alloy frame. The frame is fixed on the shaft of the worm gear, which is driven by the step motor through the worm. The shaft of the potentiometer is connected to that of the worm gear to measure the rotation angle of the diffuse plate through a flexible coupler. Firstly, the calibration mechanism is designed, which includes the LEDs assembly design, the worm gear reducer design and the diffuse plate assembly design. The counterweight blocks and two end stops are also designed for the diffuse plate assembly. Then a modal analysis with finite element method for the diffuse plate assembly is completed.

Evaluation of the Revolver Ignition Design at the National Ignition Facility Using Polar-Direct-Drive Illumination

NASA Astrophysics Data System (ADS)

McKenty, P. W.; Collins, T. J. B.; Marozas, J. A.; Campbell, E. M.; Molvig, K.; Schmitt, M.

2017-10-01

The direct-drive ignition design Revolver employs a triple-shell target using a beryllium ablator, a copper driver, and an eventual gold pusher. Symmetric numerical calculations indicate that each of the three shells exhibit low convergence ( 3to 5) resulting in a modest gain (G 4) for 1.7 MJ of incident laser energy. Studies are now underway to evaluate the robustness of this design employing polar direct drive (PDD) at the National Ignition Facility. Integral to these calculations is the leveraging of illumination conditioning afforded by research done to demonstrate ignition for a traditional PDD hot-spot target design. Two-dimensional simulation results, employing nonlocal electron-thermal transport and cross-beam energy transport, will be presented that indicate ignition using PDD. A study of the allowed levels of long-wavelength perturbations (target offset and power imbalance) not precluding ignition will also be examined. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

A balanced ATP driving force module for enhancing photosynthetic biosynthesis of 3-hydroxybutyrate from CO2.

PubMed

Ku, Jason T; Lan, Ethan I

2018-03-01

Using engineered photoautotrophic microorganisms for the direct chemical synthesis from CO 2 is an attractive direction for both sustainability and CO 2 mitigation. However, the behaviors of non-native metabolic pathways may be difficult to control due to the different intracellular contexts between natural and heterologous hosts. While most metabolic engineering efforts focus on strengthening driving forces in pathway design to favor biochemical production in these organisms, excessive driving force may be detrimental to product biosynthesis due to imbalanced cellular intermediate distribution. In this study, an ATP-hydrolysis based driving force module was engineered into cyanobacterium Synechococcus elongatus PCC 7942 to produce 3-hydroxybutyrate (3HB), a valuable chemical feedstock for the synthesis of biodegradable plastics and antibiotics. However, while the ATP driving force module is effective for increasing product formation, uncontrolled accumulation of intermediate metabolites likely led to metabolic imbalance and thus to cell growth inhibition. Therefore, the ATP driving force module was reengineered by providing a reversible outlet for excessive carbon flux. Upon expression of this balanced ATP driving force module with 3HB biosynthesis, engineered strain produced 3HB with a cumulative titer of 1.2 g/L, a significant increase over the initial strain. This result highlighted the importance of pathway reversibility as an effective design strategy for balancing driving force and intermediate accumulation, thereby achieving a self-regulated control for increased net flux towards product biosynthesis. Copyright © 2018 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

Improved motors for utility applications: Volume 6, Squirrel-cage rotor analysis: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffith, J.W.; McCoy, R.M.

1986-11-01

An analysis of squirrel cage induction motor rotors was undertaken in response to an Industry Assessment Study finding 10% of motor failures to be rotor related. The analysis focuses on evaluating rotor design life. The evaluation combines state-of-the-art electromagnetic, thermal, and structural solution techniques into an integrated analysis and presents a simple summary. Finite element techniques are central tools in the analysis. The analysis is applied to a specific forced draft fan drive design. Fans as a category of application have a higher failure rate than other categories of power station auxiliary motor applications. Forced-draft fan drives are one ofmore » the major fan drives which accelerate a relatively high value of rotor load inertia. Various starting and operating conditions are studied for this forced-draft fan drive motor including a representative application duty cycle.« less

Single mask, simple structure micro rotational motor driven by electrostatic comb-drive actuators

NASA Astrophysics Data System (ADS)

Pham, Phuc Hong; Viet Dao, Dzung; Dang, Lam Bao; Sugiyama, Susumu

2012-01-01

We report a design and fabrication of a new micro rotational motor (MRM) using silicon micromachining technology with the overall diameter of 2.4 mm. This motor utilizes four silicon electrostatic comb-drive actuators to drive the outer ring (or rotor) through ratchet teeth. The novel design of the anti-reverse structure helps us to overcome the gap problem after deep reactive ion etching of silicon. The MRM was fabricated by using silicon on insulator wafer with the thickness of the device layer being 30 µm and one mask only. The motor was successfully tested for performance. It was driven by periodic voltage with different frequencies ranging from 1 to 50 Hz. The angular velocity of the outer ratchet ring was proportional to the frequency. Moreover, when the driving frequency is lower than 30 Hz, the experiment results perfectly match the theoretical calculation.

The effects of social interactions with in-vehicle agents on a driver's anger level, driving performance, situation awareness, and perceived workload.

PubMed

Jeon, Myounghoon; Walker, Bruce N; Gable, Thomas M

2015-09-01

Research has suggested that interaction with an in-vehicle software agent can improve a driver's psychological state and increase road safety. The present study explored the possibility of using an in-vehicle software agent to mitigate effects of driver anger on driving behavior. After either anger or neutral mood induction, 60 undergraduates drove in a simulator with two types of agent intervention. Results showed that both speech-based agents not only enhance driver situation awareness and driving performance, but also reduce their anger level and perceived workload. Regression models show that a driver's anger influences driving performance measures, mediated by situation awareness. The practical implications include design guidelines for the design of social interaction with in-vehicle software agents. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Stability of entrainment of a continuum of coupled oscillators

DOE PAGES

Snyder, Jordan; Zlotnik, Anatoly; Hagberg, Aric

2017-10-05

Complex natural and engineered systems are ubiquitous, and their behavior is challenging to characterize and control. Here, we examine the design of the entrainment process for an uncountably infinite collection of coupled phase oscillators that are all subject to the same periodic driving signal. In the absence of coupling, an appropriately designed input can result in each oscillator attaining the frequency of the driving signal, with a phase offset determined by its natural frequency. We also consider a special case of interacting oscillators in which the coupling tends to destabilize the phase configuration to which the driving signal would sendmore » the collection in the absence of coupling. In this setting, we derive stability results that characterize the trade-off between the effects of driving and coupling, and compare these results to the well-known Kuramoto model of a collection of free-running coupled oscillators.« less

Stability of entrainment of a continuum of coupled oscillators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, Jordan; Zlotnik, Anatoly; Hagberg, Aric

Complex natural and engineered systems are ubiquitous, and their behavior is challenging to characterize and control. Here, we examine the design of the entrainment process for an uncountably infinite collection of coupled phase oscillators that are all subject to the same periodic driving signal. In the absence of coupling, an appropriately designed input can result in each oscillator attaining the frequency of the driving signal, with a phase offset determined by its natural frequency. We also consider a special case of interacting oscillators in which the coupling tends to destabilize the phase configuration to which the driving signal would sendmore » the collection in the absence of coupling. In this setting, we derive stability results that characterize the trade-off between the effects of driving and coupling, and compare these results to the well-known Kuramoto model of a collection of free-running coupled oscillators.« less

A Comprehensive Review of Permanent Magnet Transverse Flux Machines for Direct Drive Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muljadi, Eduard; Husain, Tausif; Hasan, Iftekhar

The use of direct drive machines in renewable and industrial applications are increasing at a rapid rate. Transverse flux machines (TFM) are ideally suited for direct drive applications due to their high torque density. In this paper, a comprehensive review of the permanent magnet (PM) TFMs for direct drive applications is presented. The paper introduces TFMs and their operating principle and then reviews the different type of TFMs proposed in the literature. The TFMs are categorized according to the number of stator sides, types of stator cores and magnet arrangement in the rotor. The review covers different design topologies, materialsmore » used for manufacturing, structural and thermal analysis, modeling and design optimization and cogging torque minimization in TFMs. The paper also reviews various applications and comparisons for TFMs that have been presented in the literature.« less

Transistorized PWM inverter-induction motor drive system

NASA Technical Reports Server (NTRS)

Peak, S. C.; Plunkett, A. B.

1982-01-01

This paper describes the development of a transistorized PWM inverter-induction motor traction drive system. A vehicle performance analysis was performed to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of inverter and motor specifications. The inverter was a transistorized three-phase bridge using General Electric power Darlington transistors. The description of the design and development of this inverter is the principal object of this paper. The high-speed induction motor is a design which is optimized for use with an inverter power source. The primary feedback control is a torque angle control with voltage and torque outer loop controls. A current-controlled PWM technique is used to control the motor voltage. The drive has a constant torque output with PWM operation to base motor speed and a constant horsepower output with square wave operation to maximum speed. The drive system was dynamometer tested and the results are presented.

High-Density Digital Data Storage System

NASA Technical Reports Server (NTRS)

Wright, Kenneth D.; Gray, David L.

1995-01-01

High-density digital data storage system designed for cost-effective storage of large amounts of information acquired during experiments. System accepts up to 20 channels of 16-bit digital data with overall transfer rates of 500 kilobytes per second. Data recorded on 8-millimeter magnetic tape in cartridges, each capable of holding up to five gigabytes of data. Each cartridge mounted on one of two tape drives. Operator chooses to use either or both of drives. One drive used for primary storage of data while other can be used to make a duplicate record of data. Alternatively, other drive serves as backup data-storage drive when primary one fails.

77 FR 11199 - Visual-Manual NHTSA Driver Distraction Guidelines for In-Vehicle Electronic Devices

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-24

...The National Highway Traffic Safety Administration (NHTSA) is concerned about the effects of distraction due to drivers' use of electronic devices on motor vehicle safety. Consequently, NHTSA is issuing nonbinding, voluntary NHTSA Driver Distraction Guidelines (NHTSA Guidelines) to promote safety by discouraging the introduction of excessively distracting devices in vehicles. This notice details the contents of the first phase of the NHTSA Driver Distraction Guidelines. These NHTSA Guidelines cover original equipment in-vehicle device secondary tasks (communications, entertainment, information gathering, and navigation tasks not required to drive are considered secondary tasks) performed by the driver through visual-manual means (meaning the driver looking at a device, manipulating a device-related control with the driver's hand, and watching for visual feedback). The proposed NHTSA Guidelines list certain secondary, non-driving related tasks that, based on NHTSA's research, are believed by the agency to interfere inherently with a driver's ability to safely control the vehicle. The Guidelines recommend that those in-vehicle devices be designed so that they cannot be used by the driver to perform such tasks while the driver is driving. For all other secondary, non-driving-related visual-manual tasks, the NHTSA Guidelines specify a test method for measuring the impact of task performance on driving safety while driving and time-based acceptance criteria for assessing whether a task interferes too much with driver attention to be suitable to perform while driving. If a task does not meet the acceptance criteria, the NHTSA Guidelines recommend that in- vehicle devices be designed so that the task cannot be performed by the driver while driving. In addition to identifying inherently distracting tasks and providing a means for measuring and evaluating the level of distraction associated with other non-driving-related tasks, the NHTSA Guidelines contain several design recommendations for in-vehicle devices in order to minimize their potential for distraction. NHTSA seeks comments on these NHTSA Guidelines and any suggestions for how to improve them so as to better enhance motor vehicle safety.

AVIRIS scan drive design and performance

NASA Technical Reports Server (NTRS)

Miller, D. C.

1987-01-01

The Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) images the ground with an instantaneous field of view (IFOV) of 1 mrad. The IFOV is scanned 30 deg from left to right to provide the cross-track dimension of the image, while the aircraft's motion provides the along-track dimension. The scanning frequency is 12 Hz, with a scan efficiency of 70 percent. The scan mirror has an effective diameter of 5.7 in, and its positional accuracy is a small fraction of a milliradian of the nominal position-time profile. Described are the design and performance of the scan drive mechanism. Tradeoffs among various approaches are discussed, and the reasons given for the selection of the cam drive.

Mechanical-thermal noise in drive-mode of a silicon micro-gyroscope.

PubMed

Yang, Bo; Wang, Shourong; Li, Hongsheng; Zhou, Bailing

2009-01-01

A new closed-loop drive scheme which decouples the phase and the gain of the closed-loop driving system was designed in a Silicon Micro-Gyroscope (SMG). We deduce the system model of closed-loop driving and use stochastic averaging to obtain an approximate "slow" system that clarifies the effect of thermal noise. The effects of mechanical-thermal noise on the driving performance of the SMG, including the noise spectral density of the driving amplitude and frequency, are derived. By calculating and comparing the noise amplitude due to thermal noise both in the opened-loop driving and in the closed-loop driving, we find that the closed-loop driving does not reduce the RMS noise amplitude. We observe that the RMS noise frequency can be reduced by increasing the quality factor and the drive amplitude in the closed-loop driving system. The experiment and simulation validate the feasibility of closed-loop driving and confirm the validity of the averaged equation and its stablility criterion. The experiment and simulation results indicate the electrical noise of closed-loop driving circuitry is bigger than the mechanical-thermal noise and as the driving mass decreases, the mechanical-thermal noise may get bigger than the electrical noise of the closed-loop driving circuitry.

Ultra-Compact Multitip Scanning Probe Microscope with an Outer Diameter of 50 mm

NASA Astrophysics Data System (ADS)

Cherepanov, Vasily; Zubkov, Evgeny; Junker, Hubertus; Korte, Stefan; Blab, Marcus; Coenen, Peter; Voigtländer, Bert

We present a multitip scanning tunneling microscope (STM) where four independent STM units are integrated on a diameter of 50 mm. The coarse positioning of the tips is done under the control of an optical microscope or an SEM in vacuum. The heart of this STM is a new type of piezoelectric coarse approach called Koala Drive which can have a diameter greater than 2.5 mm and a length smaller than 10 mm. Alternating movements of springs move a central tube which holds the STM tip or AFM sensor. This new operating principle provides a smooth travel sequence and avoids shaking which is intrinsically present for nanopositioners based on inertial motion with saw tooth driving signals. Inserting the Koala Drive in a piezo tube for xyz-scanning integrates a complete STM inside a 4 mm outer diameter piezo tube of <10 mm length. The use of the Koala Drive makes the scanning probe microscopy design ultra-compact and accordingly leads to a high mechanical stability. The drive is UHV, low temperature, and magnetic field compatible. The compactness of the Koala Drive allows building a four-tip STM as small as a single-tip STM with a drift of <0.2 nm/min and lowest resonance frequencies of 2.5 (xy) and 5.5 kHz (z). We present examples of the performance of the multitip STM designed using the Koala Drive.

Prediction of safe driving Behaviours based on health belief model: the case of taxi drivers in Bandar Abbas, Iran.

PubMed

Razmara, Asghar; Aghamolaei, Teamur; Madani, Abdoulhossain; Hosseini, Zahra; Zare, Shahram

2018-03-20

Road accidents are among the main causes of mortality. As safe and secure driving is a key strategy to reduce car injuries and offenses, the present research aimed to explore safe driving behaviours among taxi drivers based on the Health Belief Model (HBM). This study was conducted on 184 taxi drivers in Bandar Abbas who were selected based on a multiple stratified sampling method. Data were collected by a questionnaire comprised of a demographic information section along with the constructs of the HBM. Data were analysed by SPSS ver19 via a Pearson's correlation coefficient and multiple regressions. The mean age of the participants was 45.1 years (SD = 11.1). They all had, on average, 10.3 (SD = 7/5) years of taxi driving experience. Among the HBM components, cues to action and perceived benefits were shown to be positively correlated with safe driving behaviours, while perceived barriers were negatively correlated. Cues to action, perceived barriers and perceived benefits were shown to be the strongest predictors of a safe drivers' behaviour. Based on the results of this study in designing health promotion programmes to improve safe driving behaviours among taxi drivers, cues to action, perceived benefits and perceived barriers are important. Therefore, advertising, the design of information campaigns, emphasis on the benefits of safe driving behaviours and modification barriers are recommended.

Preventing texting while driving: a statement of the American College of Preventive Medicine.

PubMed

Sherin, Kevin M; Lowe, Andrea L; Harvey, Bart J; Leiva, Daniel F; Malik, Aaqib; Matthews, Sarah; Suh, Ryung

2014-11-01

The American College of Preventive Medicine (ACPM) is providing a set of recommendations designed to reduce the morbidity and mortality associated with distractions due to texting while driving. According to the National Highway Traffic Safety Administration, 12% of all fatal crashes involving at least one distracted driver are estimated to be related to cell phone use while driving. Given the combination of visual, manual, and cognitive distractions posed by texting, this is an issue of major public health concern for communities. Therefore, the ACPM feels it is timely to discuss this issue and provide the following recommendations: 1. Encourage state legislatures to develop and pass legislation banning texting while driving, while simultaneously implementing comprehensive and dedicated law enforcement strategies including penalties for these violations. Legislatures should establish a public awareness campaign regarding the dangers of texting while driving as an integral part of this legislation. 2. Promote further research into the design and evaluation of educational tools regarding texting while driving that can be incorporated into the issuance of driver’s licenses. 3. Provide primary care providers with the appropriate tools to educate patients of all ages. 4. Conduct additional studies investigating the risks associated with cell phone usage while driving, particularly texting, with motor vehicle crashes. Copyright © 2014 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

A driving simulator study of driver performance on deceleration lanes.

PubMed

Calvi, A; Benedetto, A; De Blasiis, M R

2012-03-01

Deceleration lanes are important because they help drivers transition from high-speed lanes to low-speed ramps. Although they are designed to allow vehicles to depart the freeway safely and efficiently, many studies report high accident rates on exit ramps with the highest percentage of crashes taking place in deceleration lanes. This paper describes the results of a driving simulator study that focused on driving performance while approaching a divergence area and decelerating during the exiting maneuver. Three different traffic scenarios were simulated to analyze the influence of traffic volume on driving performance. Thirty drivers drove in the simulator in these scenarios while data on their lateral position, speed and deceleration were collected. Our results indicate there are considerable differences between the main assumptions of models generally used to design deceleration lanes and actual driving performance. In particular, diverging drivers begin to decelerate before arriving at the deceleration lane, causing interference with the main flow. Moreover, speeds recorded at the end of the deceleration lane exceed those for which the ramp's curves are designed; this creates risky driving conditions that could explain the high crash rates found in studies of exit ramps. Finally, statistical analyses demonstrate significant influences of traffic volume on some aspects of exiting drivers' performance: lower traffic volume results in elevated exiting speed and deceleration, and diverging drivers begin to decelerate earlier along the main lane when traffic volume is low. However, speeds at the end of the deceleration lane and the site of lane changing are not significantly influenced by traffic volume. Copyright © 2011 Elsevier Ltd. All rights reserved.

Statistical Models for Predicting Automobile Driving Postures for Men and Women Including Effects of Age.

PubMed

Park, Jangwoon; Ebert, Sheila M; Reed, Matthew P; Hallman, Jason J

2016-03-01

Previously published statistical models of driving posture have been effective for vehicle design but have not taken into account the effects of age. The present study developed new statistical models for predicting driving posture. Driving postures of 90 U.S. drivers with a wide range of age and body size were measured in laboratory mockup in nine package conditions. Posture-prediction models for female and male drivers were separately developed by employing a stepwise regression technique using age, body dimensions, vehicle package conditions, and two-way interactions, among other variables. Driving posture was significantly associated with age, and the effects of other variables depended on age. A set of posture-prediction models is presented for women and men. The results are compared with a previously developed model. The present study is the first study of driver posture to include a large cohort of older drivers and the first to report a significant effect of age. The posture-prediction models can be used to position computational human models or crash-test dummies for vehicle design and assessment. © 2015, Human Factors and Ergonomics Society.

Fatigue life analysis for traction drives with application to a toroidal type geometry

NASA Technical Reports Server (NTRS)

Coy, J. J.; Loewenthal, S. H.; Zaretsky, E. V.

1976-01-01

A contact fatigue life analysis for traction drives was developed which was based on a modified Lundberg-Palmgren theory. The analysis was used to predict life for a cone-roller toroidal traction drive. A 90-percent probability of survival was assumed for the calculated life. Parametric results were presented for life and Hertz contact stress as a function of load, drive ratio, and size. A design study was also performed. The results were compared to previously published work for the dual cavity toroidal drive as applied to a typical compact passenger vehicle drive train. For a representative duty cycle condition wherein the engine delivers 29 horsepower at 2000 rpm with the vehicle moving at 48.3 km/hr (30 mph) the drive life was calculated to be 19,200 km (11 900 miles).

The utility of the AusEd driving simulator in the clinical assessment of driver fatigue.

PubMed

Desai, Anup V; Wilsmore, Brad; Bartlett, Delwyn J; Unger, Gunnar; Constable, Ben; Joffe, David; Grunstein, Ronald R

2007-08-01

Several driving simulators have been developed which range in complexity from PC based driving tasks to advanced "real world" simulators. The AusEd driving simulator is a PC based task, which was designed to be conducive to and test for driver fatigue. This paper describes the AusEd driving simulator in detail, including the technical requirements, hardware, screen and file outputs, and analysis software. Some aspects of the test are standardized, while others can be modified to suit the experimental situation. The AusEd driving simulator is sensitive to performance decrement from driver fatigue in the laboratory setting, potentially making it useful as a laboratory or office based test for driver fatigue risk management. However, more research is still needed to correlate laboratory based simulator performance with real world driving performance and outcomes.

Utility of an Occupational Therapy Driving Intervention for a Combat Veteran

PubMed Central

Monahan, Miriam; Canonizado, Maria; Winter, Sandra

2014-01-01

Many combat veterans are injured in motor vehicle crashes shortly after returning to civilian life, yet little evidence exists on effective driving interventions. In this single-subject design study, we compared clinical test results and driving errors in a returning combat veteran before and after an occupational therapy driving intervention. A certified driving rehabilitation specialist administered baseline clinical and simulated driving assessments; conducted three intervention sessions that discussed driving errors, retrained visual search skills, and invited commentary on driving; and administered a postintervention evaluation in conditions resembling those at baseline. Clinical test results were similar pre- and postintervention. Baseline versus postintervention driving errors were as follows: lane maintenance, 23 versus 7; vehicle positioning, 5 versus 1; signaling, 2 versus 0; speed regulation, 1 versus 1; visual scanning, 1 versus 0; and gap acceptance, 1 versus 0. Although the intervention appeared efficacious for this participant, threats to validity must be recognized and controlled for in a follow-up study. PMID:25005503

Driver license testing of young novice drivers : traffic tech.

DOT National Transportation Integrated Search

2010-11-01

Driver license tests are designed to ensure that people using : public roadways have a minimum level of driving skill and : an awareness of safe driving practices and road laws. License : applicants proceed through the administrative processes of : t...

Career Oriented Mathematics, Teacher's Manual. [Includes Mastering Computational Skill: A Use-Based Program; Owning an Automobile and Driving as a Career; Retail Sales; Measurement; and Area-Perimeter.

ERIC Educational Resources Information Center

Mahaffey, Michael L.; McKillip, William D.

This manual is designed for teachers using the Career Oriented Mathematics units on owning an automobile and driving as a career, retail sales, measurement, and area-perimeter. The volume begins with a discussion of the philosophy and scheduling of the program which is designed to improve students' attitudes and ability in computation by…

Surface micromachined microengine as the driver for micromechanical gears

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, E.J.; Sniegowski, J.J.

1995-05-01

The transmission of mechanical power is often accomplished through the use of gearing. The recently developed surface micromachined microengine provides us with an actuator which is suitable for driving surface micromachined geared systems. In this paper we will present aspects of the microengine as they relate to the driving of geared mechanisms, issues relating to the design of micro gear mechanisms, and details of a design of a microengine-driven geared shutter mechanism.

Surf-zone Underwater Robotic Demonstration Platform

DTIC Science & Technology

2014-01-01

dynamically advantageous shape for a robotic system. To address locomotive factors ARA completed a research and technical study based on an Archimedes ...effective hull shape. To study mobility and traction a propulsion system based on an Archimedes screw drive was used. A drive design based on an... Archimedes screw was chosen because of its ability to operate in various mediums with varying flow rates. A test bed was designed and assembled in order to

Gear Drive Testing

NASA Technical Reports Server (NTRS)

1982-01-01

Philadelphia Gear Corporation used two COSMIC computer programs; one dealing with shrink fit analysis and the other with rotor dynamics problems in computerized design and test work. The programs were used to verify existing in-house programs to insure design accuracy by checking its company-developed computer methods against procedures developed by other organizations. Its specialty is in custom units for unique applications, such as Coast Guard ice breaking ships, steel mill drives, coal crusher, sewage treatment equipment and electricity.

Variable-frequency synchronous motor drives for electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chalmers, B.J.; Musaba, L.; Gosden, D.F.

1996-07-01

The performance capability envelope of a variable-frequency, permanent-magnet synchronous motor drive with field weakening is dependent upon the product of maximum current and direct-axis inductance. To obtain a performance characteristic suitable for a typical electric vehicle drive, in which short-term increase of current is applied, it is necessary to design an optimum value of direct-axis inductance. The paper presents an analysis of a hybrid motor design which uses a two-part rotor construction comprising a surface-magnet part and an axially laminated reluctance part. This arrangement combines the properties of all other types of synchronous motor and offers a greater choice ofmore » design variables. It is shown that the desired form of performance may be achieved when the high-inductance axis of the reluctance part is arranged to lead the magnet axis by 90{degree} (elec.).« less

An open-source laser electronics suite

NASA Astrophysics Data System (ADS)

Pisenti, Neal C.; Reschovsky, Benjamin J.; Barker, Daniel S.; Restelli, Alessandro; Campbell, Gretchen K.

2016-05-01

We present an integrated set of open-source electronics for controlling external-cavity diode lasers and other instruments in the laboratory. The complete package includes a low-noise circuit for driving high-voltage piezoelectric actuators, an ultra-stable current controller based on the design of, and a high-performance, multi-channel temperature controller capable of driving thermo-electric coolers or resistive heaters. Each circuit (with the exception of the temperature controller) is designed to fit in a Eurocard rack equipped with a low-noise linear power supply capable of driving up to 5 A at +/- 15 V. A custom backplane allows signals to be shared between modules, and a digital communication bus makes the entire rack addressable by external control software over TCP/IP. The modular architecture makes it easy for additional circuits to be designed and integrated with existing electronics, providing a low-cost, customizable alternative to commercial systems without sacrificing performance.

Viper cabin-fuselage structural design concept with engine installation and wing structural design

NASA Technical Reports Server (NTRS)

Marchesseault, B.; Carr, D.; Mccorkle, T.; Stevens, C.; Turner, D.

1993-01-01

This report describes the process and considerations in designing the cabin, nose, drive shaft, and wing assemblies for the 'Viper' concept aircraft. Interfaces of these assemblies, as well as interfaces with the sections of the aircraft aft of the cabin, are also discussed. The results of the design process are included. The goal of this project is to provide a structural design which complies with FAR 23 requirements regarding occupant safety, emergency landing loads, and maneuvering loads. The design must also address the interfaces of the various systems in the cabin, nose, and wing, including the drive shaft, venting, vacuum, electrical, fuel, and control systems. Interfaces between the cabin assembly and the wing carrythrough and empennage assemblies were required, as well. In the design of the wing assemblies, consistency with the existing cabin design was required. The major areas considered in this report are materials and construction, loading, maintenance, environmental considerations, wing assembly fatigue, and weight. The first three areas are developed separately for the nose, cabin, drive shaft, and wing assemblies, while the last three are discussed for the entire design. For each assembly, loading calculations were performed to determine the proper sizing of major load carrying components. Table 1.0 lists the resulting margins of safety for these key components, along with the types of the loads involved, and the page number upon which they are discussed.

[Design and validation of a questionnaire exploring risky-driving patterns in young drivers].

PubMed

Jiménez Mejías, Eladio; Luna del Castillo, Juan de Dios; Amezcua Prieto, Carmen; Olvera Porcel, María Carmen; Lardelli Claret, Pablo; Jiménez Moleón, José Juan

2012-01-01

Traffic Injuries are a major public health problem, especially among young people. However, we have not found any useful questionnaire designed in our country for the epidemiological research in this field. The objective of this study was to design and validate an easy and quickly-to-fill questionnaire aimed to collect information on how frequently university car drivers report to be involved in driving circumstances theoretically related to traffic crashes. Between 2007 and 2010, a total of 1597 young undergraduate students at the University of Granada answered a self-administered questionnaire collecting information about exposure, accidents and involvement in 28 different driving circumstances. For designing this questionnaire, an extensive literature review was carried out and the opinions of five experts in a panel were also taken into account. By applying the tetracoric correlation coefficient, we conducted a factor analysis. Internal consistency was assessed using Cronbach's alpha coefficient. Finally, we evaluated the crude and adjusted association of each identified factor with the odds for having suffered an accident. After excluding 8 circumstances, the remaining ones were grouped into three factors: the first one included ten high-prevalence circumstances and explained 31.9% of the total variability. Meanwhile, the other two factors included five circumstances each one which respectively explained 15.2% and 12.5% of the variability. Cronbach's alpha coefficients ranged between 0.816 and 0.553. When adjustments according age, sex, years in possession of the driving license and intensity of exposure were made, the first factor obtained the score more strongly associated with the accident rate (OR = 1.51; CI95%: 1.25-1.85). The final version (20 circumstances) identified three factors related to higher accident rates among the young drivers. The first one integrated, among other circumstances, the excessive speed and driving while sleepy or tired and it was the most closely associated with the accident rate in the adjusted analysis. The second factor included, among others, the commission of driving offences, and the third one included driving under the influence of alcohol, not always wearing the seat belt and distractions.

Monitoring sleepiness with on-board electrophysiological recordings for preventing sleep-deprived traffic accidents.

PubMed

Papadelis, Christos; Chen, Zhe; Kourtidou-Papadeli, Chrysoula; Bamidis, Panagiotis D; Chouvarda, Ioanna; Bekiaris, Evangelos; Maglaveras, Nikos

2007-09-01

The objective of this study is the development and evaluation of efficient neurophysiological signal statistics, which may assess the driver's alertness level and serve as potential indicators of sleepiness in the design of an on-board countermeasure system. Multichannel EEG, EOG, EMG, and ECG were recorded from sleep-deprived subjects exposed to real field driving conditions. A number of severe driving errors occurred during the experiments. The analysis was performed in two main dimensions: the macroscopic analysis that estimates the on-going temporal evolution of physiological measurements during the driving task, and the microscopic event analysis that focuses on the physiological measurements' alterations just before, during, and after the driving errors. Two independent neurophysiologists visually interpreted the measurements. The EEG data were analyzed by using both linear and non-linear analysis tools. We observed the occurrence of brief paroxysmal bursts of alpha activity and an increased synchrony among EEG channels before the driving errors. The alpha relative band ratio (RBR) significantly increased, and the Cross Approximate Entropy that quantifies the synchrony among channels also significantly decreased before the driving errors. Quantitative EEG analysis revealed significant variations of RBR by driving time in the frequency bands of delta, alpha, beta, and gamma. Most of the estimated EEG statistics, such as the Shannon Entropy, Kullback-Leibler Entropy, Coherence, and Cross-Approximate Entropy, were significantly affected by driving time. We also observed an alteration of eyes blinking duration by increased driving time and a significant increase of eye blinks' number and duration before driving errors. EEG and EOG are promising neurophysiological indicators of driver sleepiness and have the potential of monitoring sleepiness in occupational settings incorporated in a sleepiness countermeasure device. The occurrence of brief paroxysmal bursts of alpha activity before severe driving errors is described in detail for the first time. Clear evidence is presented that eye-blinking statistics are sensitive to the driver's sleepiness and should be considered in the design of an efficient and driver-friendly sleepiness detection countermeasure device.

Estimation of the Driving Style Based on the Users' Activity and Environment Influence.

PubMed

Sysoev, Mikhail; Kos, Andrej; Guna, Jože; Pogačnik, Matevž

2017-10-21

New models and methods have been designed to predict the influence of the user's environment and activity information to the driving style in standard automotive environments. For these purposes, an experiment was conducted providing two types of analysis: (i) the evaluation of a self-assessment of the driving style; (ii) the prediction of aggressive driving style based on drivers' activity and environment parameters. Sixty seven h of driving data from 10 drivers were collected for analysis in this study. The new parameters used in the experiment are the car door opening and closing manner, which were applied to improve the prediction accuracy. An Android application called Sensoric was developed to collect low-level smartphone data about the users' activity. The driving style was predicted from the user's environment and activity data collected before driving. The prediction was tested against the actual driving style, calculated from objective driving data. The prediction has shown encouraging results, with precision values ranging from 0.727 up to 0.909 for aggressive driving recognition rate. The obtained results lend support to the hypothesis that user's environment and activity data could be used for the prediction of the aggressive driving style in advance, before the driving starts.

Driver training interests of a Spanish sample of young drivers and its relationship with their self-assessment skills concerning risky driving behavior.

PubMed

Molina, J Gabriel; Sanmartín, Jaime; Keskinen, Esko

2013-03-01

Poor driving self-assessment skills (e.g., over-confidence) have been pointed out as an important explanatory factor behind young drivers' accident involvement. This paper explores (1) what young drivers miss in their training as drivers in order to analyze whether an assessment of one's own driving skills plays an important role in their desire to improve as drivers, and (2) how these training interests are related to an estimate of their self-assessment skills concerning risky driving behavior. For this purpose, a study was conducted using a survey with a blocked sampling design of novice drivers. The survey solicited respondents' self-report about (1) the contents of training courses that they feel would improve their driving, (2) their risky driving behavior, and (3) their likelihood of being involved in a risky driving situation. From the initial sample invited to participate, of nearly 1300 people, we finally obtained complete data from 321 young Spanish drivers. Two main results were apparent from our data analysis: (1) the novice drivers were mainly interested in improving their ability to recognize their strengths and weaknesses as drivers (i.e., self-assessment skills); (2) a significant relationship was found between novice drivers' interests and their current self-assessment skills concerning risky driving behavior. Specifically, there was greater general interest expressed in post-license training by the under-confident self-assessors than the over-confident ones. These results provide a relevant input which should be taken into account when designing driver training programs for novice drivers. Moreover, the relationship between their training interests and their risky driving self-assessment skills introduces an additional factor to be considered in the implementation of these training programs. Copyright © 2012 Elsevier Ltd. All rights reserved.

Stability condition for the drive bunch in a collinear wakefield accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baturin, S. S.; Zholents, A.

The beam breakup instability of the drive bunch in the structure-based collinear wakefield accelerator is considered and a stabilizing method is proposed. The method includes using the specially designed beam focusing channel, applying the energy chirp along the electron bunch, and keeping energy chirp constant during the drive bunch deceleration. A stability condition is derived that defines the limit on the accelerating field for the witness bunch.

Assessment of wheelchair driving performance in a virtual reality-based simulator

PubMed Central

Mahajan, Harshal P.; Dicianno, Brad E.; Cooper, Rory A.; Ding, Dan

2013-01-01

Objective To develop a virtual reality (VR)-based simulator that can assist clinicians in performing standardized wheelchair driving assessments. Design A completely within-subjects repeated measures design. Methods Participants drove their wheelchairs along a virtual driving circuit modeled after the Power Mobility Road Test (PMRT) and in a hallway with decreasing width. The virtual simulator was displayed on computer screen and VR screens and participants interacted with it using a set of instrumented rollers and a wheelchair joystick. Driving performances of participants were estimated and compared using quantitative metrics from the simulator. Qualitative ratings from two experienced clinicians were used to estimate intra- and inter-rater reliability. Results Ten regular wheelchair users (seven men, three women; mean age ± SD, 39.5 ± 15.39 years) participated. The virtual PMRT scores from the two clinicians show high inter-rater reliability (78–90%) and high intra-rater reliability (71–90%) for all test conditions. More research is required to explore user preferences and effectiveness of the two control methods (rollers and mathematical model) and the display screens. Conclusions The virtual driving simulator seems to be a promising tool for wheelchair driving assessment that clinicians can use to supplement their real-world evaluations. PMID:23820148

Design and modeling of magnetically driven electric-field sensor for non-contact DC voltage measurement in electric power systems.

PubMed

Wang, Decai; Li, Ping; Wen, Yumei

2016-10-01

In this paper, the design and modeling of a magnetically driven electric-field sensor for non-contact DC voltage measurement are presented. The magnetic drive structure of the sensor is composed of a small solenoid and a cantilever beam with a cylindrical magnet mounted on it. The interaction of the magnet and the solenoid provides the magnetic driving force for the sensor. Employing magnetic drive structure brings the benefits of low driving voltage and large vibrating displacement, which consequently results in less interference from the drive signal. In the theoretical analyses, the capacitance calculation model between the wire and the sensing electrode is built. The expression of the magnetic driving force is derived by the method of linear fitting. The dynamical model of the magnetic-driven cantilever beam actuator is built by using Euler-Bernoulli theory and distributed parameter method. Taking advantage of the theoretical model, the output voltage of proposed sensor can be predicted. The experimental results are in good agreement with the theoretical results. The proposed sensor shows a favorable linear response characteristic. The proposed sensor has a measuring sensitivity of 9.87 μV/(V/m) at an excitation current of 37.5 mA. The electric field intensity resolution can reach 10.13 V/m.

A roadmap for interpreting the literature on vision and driving.

PubMed

Owsley, Cynthia; Wood, Joanne M; McGwin, Gerald

2015-01-01

Over the past several decades there has been a sharp increase in the number of studies focused on the relationship between vision and driving. The intensified attention to this topic has most likely been stimulated by the lack of an evidence basis for determining vision standards for driving licensure and a poor understanding about how vision impairment impacts driver safety and performance. Clinicians depend on the literature on vision and driving to advise visually impaired patients appropriately about driving fitness. Policy makers also depend on the scientific literature in order to develop guidelines that are evidence-based and are thus fair to persons who are visually impaired. Thus it is important for clinicians and policy makers alike to understand how various study designs and measurement methods should be interpreted so that the conclusions and recommendations they make are not overly broad, too narrowly constrained, or even misguided. We offer a methodological framework to guide interpretations of studies on vision and driving that can also serve as a heuristic for researchers in the area. Here, we discuss research designs and general measurement methods for the study of vision as they relate to driver safety, driver performance, and driver-centered (self-reported) outcomes. Copyright © 2015 Elsevier Inc. All rights reserved.

Improving design phase evaluations for high pile rebound sites [summary].

DOT National Transportation Integrated Search

2016-05-01

In Florida, many structures are built on driven piles. Though it seems straightforward, pile : driving involves complex interactions between the pile, the hammer, the soil, and driving : procedures. Soils can even rebound, or push back, after each ha...

Driving under the influence of alcohol : determining an optimum sanction.

DOT National Transportation Integrated Search

1971-01-01

Numerous elements must be considered in the design of an optimal statutory scheme for the definition and enforcement of the prohibition against driving under the influence of alcohol. Psychological factors determine the extent to which the statute ha...

Wrong-way driving at selected interstate off-ramps.

DOT National Transportation Integrated Search

1980-01-01

This study was designed to evaluate, on interstate roadways in Virginia, the use of a technique developed in California for estimating or determining incidences of wrong-way driving at off-ramps. Also, information gained from a survey of the availabl...

Interactional instruction in the teaching of driver education.

DOT National Transportation Integrated Search

1972-01-01

This project was designed to test both the short-term (through the use of standardized tests) and long-term (by an analysis of subsequent driving records) effects of small group interaction sessions on the driving attitudes and behavior of high schoo...

Plug-in hybrid electric vehicle LiFePO4 battery life implications of thermal management, driving conditions, and regional climate

NASA Astrophysics Data System (ADS)

Yuksel, Tugce; Litster, Shawn; Viswanathan, Venkatasubramanian; Michalek, Jeremy J.

2017-01-01

Battery degradation strongly depends on temperature, and many plug-in electric vehicle applications employ thermal management strategies to extend battery life. The effectiveness of thermal management depends on the design of the thermal management system as well as the battery chemistry, cell and pack design, vehicle system characteristics, and operating conditions. We model a plug-in hybrid electric vehicle with an air-cooled battery pack composed of cylindrical LiFePO4/graphite cells and simulate the effect of thermal management, driving conditions, regional climate, and vehicle system design on battery life. We estimate that in the absence of thermal management, aggressive driving can cut battery life by two thirds; a blended gas/electric-operation control strategy can quadruple battery life relative to an all-electric control strategy; larger battery packs can extend life by an order of magnitude relative to small packs used for all-electric operation; and batteries last 73-94% longer in mild-weather San Francisco than in hot Phoenix. Air cooling can increase battery life by a factor of 1.5-6, depending on regional climate and driving patterns. End of life criteria has a substantial effect on battery life estimates.

Benefits of Moderate-Z Ablators for Direct-Drive Inertial Confinement Fusion

NASA Astrophysics Data System (ADS)

Lafon, M.; Betti, R.; Anderson, K. S.; Collins, T. J. B.; Skupsky, S.; McKenty, P. W.

2014-10-01

Control of hydrodynamic instabilities and DT-fuel preheating by hot electrons produced by laser-plasma interaction is crucial in inertial confinement fusion. Moderate- Z ablators have been shown to reduce the laser imprinting on target and suppress the generation of hot electrons from the two-plasmon-decay instability. These results have motivated the use of ablators of higher- Z than pure plastic in direct-drive-ignition target designs for the National Ignition Facility (NIF). Two-dimensional radiation-hydrodynamic simulations assess the robustness of these ignition designs to laser imprint and capsule nonuniformities. The complex behavior of the hydrodynamic stability of mid- Z ablators is investigated through single and multimode simulations. A polar-drive configuration is developed within the NIF Laser System specifications for each ablator material. The use of multilayer ablators is also investigated to enhance the hydrodynamic stability. Results indicate that ignition target designs using mid- Z ablators exhibit good hydrodynamic properties, leading to high target gain for direct-drive implosions on the NIF. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944 and the Office of Fusion Energy Sciences Number DE-FG02-04ER54786.

The role of designated driver programs in the prevention of alcohol-impaired driving: a critical reassessment.

PubMed

DeJong, W; Wallack, L

1992-01-01

We review the "designated driver" concept and the current debate over its role in preventing alcohol-impaired driving. In our view, the focus on this strategy by broadcasters, the alcohol industry, and various public service groups has deflected attention from other alcohol-related problems that account for the vast majority of deaths and injuries associated with alcohol use. This focus has also distracted many public health advocates and policymakers from the bigger and more important jobs of increasing public awareness of the social, environmental, and economic factors that influence alcohol consumption and promoting debate on legislation and other public policy solutions to alcohol-impaired driving. As part of a comprehensive strategy, we strongly encourage a renewed focus on "sobriety checkpoints," strict enforcement of laws against alcohol sales to minors, alcohol advertising reform, increased excise taxes, and other public policy initiatives supported by the Surgeon General. These measures will curb underage and heavy alcohol consumption and will create a legal and social environment in which individuals are motivated to avoid impaired driving through several alternative strategies, including but not limited to the use of designated drivers.

Drinking-and-Driving-Related Cognitions Mediate the Relationship Between Alcohol Demand and Alcohol-Impaired Driving.

PubMed

Amlung, Michael; Morris, David H; Hatz, Laura E; Teeters, Jenni B; Murphy, James G; McCarthy, Denis M

2016-07-01

Elevated behavioral economic demand for alcohol has been shown to be associated with drinking and driving in college students. The present study sought to clarify the underlying mechanisms of this relationship by examining whether drinking-and-driving-related cognitions (e.g., attitudes, perceptions, and normative beliefs) mediate the association between alcohol demand and drinking and driving. A total of 134 young adult social drinkers completed an alcohol purchase task and measures of perceived dangerousness of drinking and driving, normative beliefs about drinking and driving, and perceived driving limit (i.e., perceived number of drinks one could consume and still drive safely). The frequency of drinking and driving in the past year was assessed via self-report. Individuals who reported drinking and driving exhibited greater alcohol demand (intensity, Omax, and elasticity) compared with those who did not engage in drinking and driving. Increased demand was also correlated with more favorable drinking-and-driving cognitions. Indirect effects tests revealed that perceived driving limit partially mediated the relationship between alcohol demand and drinking-and-driving behavior, even after accounting for drinking level, sex, and delay discounting. These findings provide further support for the utility of behavioral economic theory in understanding drinking-and-driving behavior. In particular, they provide evidence for one mechanism-drinking-and-driving-related cognitions-by which alcohol demand influences drinking and driving. Additional research using longitudinal and experimental designs is required to confirm this model and to identify other potential mediators.

2D stepping drive for hyperspectral systems

NASA Astrophysics Data System (ADS)

Endrödy, Csaba; Mehner, Hannes; Grewe, Adrian; Sinzinger, Stefan; Hoffmann, Martin

2015-07-01

We present the design, fabrication and characterization of a compact 2D stepping microdrive for pinhole array positioning. The miniaturized solution enables a highly integrated compact hyperspectral imaging system. Based on the geometry of the pinhole array, an inch-worm drive with electrostatic actuators was designed resulting in a compact (1 cm2) positioning system featuring a step size of about 15 µm in a 170 µm displacement range. The high payload (20 mg) as required for the pinhole array and the compact system design exceed the known electrostatic inch-worm-based microdrives.

Conceptual Design for CLIC Gun Pulser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Tao

The Compact Linear Collider (CLIC) is a proposed future electron-positron collider, designed to perform collisions at energies from 0.5 to 5 TeV, with a nominal design optimized for 3 TeV (Dannheim, 2012). The Drive Beam Accelerator consists of a thermionic DC gun, bunching section and an accelerating section. The thermionic gun needs deliver a long (~143us) pulse of current into the buncher. A pulser is needed to drive grid of the gun to generate a stable current output. This report explores the requirements of the gun pulser and potential solutions to regulate grid current.

Fuel cell drives for road vehicles

NASA Astrophysics Data System (ADS)

Charnah, R. M.

For fuel-cell driven vehicles, including buses, the fuel cell may be the main, determining factor in the system but must be integrated into the complete design process. A Low-Floor Bus design is used to illustrate this point. The influence of advances in drive-train electronics is illustrated as are novel designs for motors and mechanical transmission of power to the wheels allowing the use of novel hub assemblies. A hybrid electric power system is being deployed in which Fuel Cells produce the energy needs but are coupled with batteries especially for acceleration phases and for recuperative braking.

Dodging silver bullets: good CRISPR gene-drive design is critical for eradicating exotic vertebrates.

PubMed

Prowse, Thomas A A; Cassey, Phillip; Ross, Joshua V; Pfitzner, Chandran; Wittmann, Talia A; Thomas, Paul

2017-08-16

Self-replicating gene drives that can spread deleterious alleles through animal populations have been promoted as a much needed but controversial 'silver bullet' for controlling invasive alien species. Homing-based drives comprise an endonuclease and a guide RNA (gRNA) that are replicated during meiosis via homologous recombination. However, their efficacy for controlling wild populations is threatened by inherent polymorphic resistance and the creation of resistance alleles via non-homologous end-joining (NHEJ)-mediated DNA repair. We used stochastic individual-based models to identify realistic gene-drive strategies capable of eradicating vertebrate pest populations (mice, rats and rabbits) on islands. One popular strategy, a sex-reversing drive that converts heterozygous females into sterile males, failed to spread and required the ongoing deployment of gene-drive carriers to achieve eradication. Under alternative strategies, multiplexed gRNAs could overcome inherent polymorphic resistance and were required for eradication success even when the probability of NHEJ was low. Strategies causing homozygotic embryonic non-viability or homozygotic female sterility produced high probabilities of eradication and were robust to NHEJ-mediated deletion of the DNA sequence between multiplexed endonuclease recognition sites. The latter two strategies also purged the gene drive when eradication failed, therefore posing lower long-term risk should animals escape beyond target islands. Multiplexing gRNAs will be necessary if this technology is to be useful for insular extirpation attempts; however, precise knowledge of homing rates will be required to design low-risk gene drives with high probabilities of eradication success. © 2017 The Author(s).

DriveID: safety innovation through individuation.

PubMed

Sawyer, Ben; Teo, Grace; Mouloua, Mustapha

2012-01-01

The driving task is highly complex and places considerable perceptual, physical and cognitive demands on the driver. As driving is fundamentally an information processing activity, distracted or impaired drivers have diminished safety margins compared with non- distracted drivers (Hancock and Parasuraman, 1992; TRB 1998 a & b). This competition for sensory and decision making capacities can lead to failures that cost lives. Some groups, teens and elderly drivers for example, have patterns of systematically poor perceptual, physical and cognitive performance while driving. Although there are technologies developed to aid these different drivers, these systems are often misused and underutilized. The DriveID project aims to design and develop a passive, automated face identification system capable of robustly identifying the driver of the vehicle, retrieve a stored profile, and intelligently prescribing specific accident prevention systems and driving environment customizations.

Cell Phone Ring Suppression and HUD Caller ID: Effectiveness in Reducing Momentary Driver Distraction under Varying Workload Levels

NASA Astrophysics Data System (ADS)

Nowakowski, C.; Friedman, D.; Green, P.

2001-10-01

The purpose of the current experiment is to provide a preliminary driving simulator assessment of several hands-free design solutions with regard to the task of answering the phone while driving. Specifically, the following questions were examined: (1) Does the location of a caller ID display and the phone buttons (two HUD (Head Up Display) locations vs. phone cradle) affect either the time to answer the phone or driving performance; (2) Does the presence or absence of a ring affect either the time to answer the phone or driving performance; (3) Does increased driving workload (visual demand) affect either the time to answer the phone or driving performance; (4) What were the initial driver reactions to a HUD-based call timer.

Associations Between Driving Performance and Engaging in Secondary Tasks: A Systematic Review

PubMed Central

Ferdinand, Alva O.

2014-01-01

We conducted a systematic review and meta-analysis of the literature examining the relationship between driving performance and engaging in secondary tasks. We extracted data from abstracts of 206 empirical articles published between 1968 and 2012 and developed a logistic regression model to identify correlates of a detrimental relationship between secondary tasks and driving performance. Of 350 analyses, 80% reported finding a detrimental relationship. Studies using experimental designs were 37% less likely to report a detrimental relationship (P = .014). Studies examining mobile phone use while driving were 16% more likely to find such a relationship (P = .009). Quasi-experiments can better determine the effects of secondary tasks on driving performance and consequently serve to inform policymakers interested in reducing distracted driving and increasing roadway safety. PMID:24432925

Solar array stepping problems in satellites and solutions

NASA Astrophysics Data System (ADS)

Maharana, P. K.; Goel, P. S.

1992-01-01

The dynamics problems arising due to stepping motion of the solar arrays of spacecraft are studied. To overcome these problems, design improvements in the drive logic based on the phase plane analysis are suggested. The improved designs are applied to the Solar Array Drive Assembly (SADA) of IRS-1B and INSAT-2A satellites. In addition, an alternate torquing strategy for very successful slewing of the arrays, and with minimum excitation of flexible modes, is proposed.

Design of a Percussion and Electric Primer Gun Firing Power Supply

DTIC Science & Technology

2014-07-01

solenoid failure. As new instrumentation techniques such as high-speed video and laser interferometry have been introduced into our gun testing...to drive a solenoid into a percussion primer or ignite the M52A3B1 electric primer. To reduce power requirements, it uses charged capacitor banks to...drive the solenoid or ignite the primer. This report details the design and construction of the power supplies. 15. SUBJECT TERMS power supply

Efficient implementation of arbitrary quantum state engineering in four-state system by counterdiabatic driving

NASA Astrophysics Data System (ADS)

Wang, Song-Bai; Chen, Ye-Hong; Wu, Qi-Cheng; Shi, Zhi-Cheng; Huang, Bi-Hua; Song, Jie; Xia, Yan

2018-07-01

A scheme is proposed to implement quantum state engineering (QSE) in a four-state system via counterdiabatic driving. In the scheme, single- and multi-mode driving methods are used respectively to drive the system to a target state at a predefined time. It is found that a fast QSE can be realized by utilizing simply designed pulses. In addition, a beneficial discussion on the energy consumption between the single- and multi-mode driving protocols shows that the multi-mode driving method seems to have a wider range of applications than the single-mode driving method with respect to different parameters. Finally, the scheme is also helpful for implementing the generalization QSE in high-dimensional systems via the concept of a dressed state. Therefore, the scheme can be implemented with the present experimental technology, which is useful in quantum information processing.

Last Call: decreasing drunk driving among 21-34-year-old bar patrons.

PubMed

Rivara, Frederick P; Boisvert, Deanne; Relyea-Chew, Annemarie; Gomez, Tony

2012-01-01

Any effort to decrease the toll of drunk driving must include efforts directed at people who drink in bars, particularly young adults who use motor vehicles after drinking. We designed a multifaceted social marketing campaign, Last Call, to increase the use of designated drivers and safe rides homes among 21-34-year olds. There were three components to the intervention: (1) use of taxi stands to promote taxi use; (2) point-of-sale information to patrons at partner bars and (3) a mass media campaign to support the designated driver/safe ride home message. Among the heaviest drinkers, the programme significantly increased the use of designated drivers and increased the use of taxis by 63%.

Thermal Design Overview of the Mars Exploration Rover Project

NASA Technical Reports Server (NTRS)

Tsuyuki, Glenn

2002-01-01

Contents include the following: Mission Overview. Thermal Environments. Driving Thermal Requirements. Thermal Design Approach. Thermal Control Block Diagram. Thermal Design Description. Thermal Analysis Results Summary. Testing Plans. Issues & Concerns.

Prototype Solid State Induction Modulator for SLAC NLC

NASA Astrophysics Data System (ADS)

Cassel, R. L.; DeLamare, J. E.; Nguyen, M. N.; Pappas, G. C.; Cook, E.

2002-08-01

The Next Linear Collider accelerator proposal at SLAC requires a high efficiency, highly reliable, and low cost pulsed power modulator to drive the X band klystrons. The present NLC envisions a solid-state induction modulator design to drive up to 8 klystrons to 500kV for 3muS at 120 PPS with one modulator (>1,000 megawatt pulse, 500kW average). A prototype modulator is presently under construction, which well power 4 each 5045 SLAC klystron to greater than 380 kV for 3muS (>600 megawatt pulse, >300 kW Ave.). The modulator will be capable of driving the 8 each X band klystrons when they become available. The paper covers the design, construction, fabrication and preliminary testing of the prototype modulator.

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 2: Stage performance

NASA Technical Reports Server (NTRS)

Roelke, R. J.; Haas, J. E.

1982-01-01

The aerodynamic performance of the compressor-drive turbine of the DOE upgraded gas turbine engine was determined in low temperature air. The as-received cast rotor blading had a significantly thicker profile than design and a fairly rough surface finish. Because of these blading imperfections a series of stage tests with modified rotors were made. These included the as-cast rotor, a reduced-roughness rotor, and a rotor with blades thinned to near design. Significant performance changes were measured. Tests were also made to determine the effect of Reynolds number on the turbine performance. Comparisons are made between this turbine and the compressor-drive turbine of the DOE baseline gas turbine engine.

An Impulse Electric Motor for Driving Recording Instruments

NASA Technical Reports Server (NTRS)

Joachim, W F

1923-01-01

The chief purpose in undertaking the development of this synchronous motor was the creation of a very small, compact power source, capable of driving the film drums of the recording aircraft instruments designed by the staff of the National Advisory Committee for Aeronautics.

Potential determinants of drink driving in young adults.

PubMed

González-Iglesias, Beatriz; Gómez-Fraguela, José António; Sobral, Jorge

2015-01-01

The main purposes of this study were to examine the usefulness of the variables of the theory of planned behavior (viz. attitudes, social norms, and self-efficacy) and to explore the relationship between optimism bias and drink driving in young adults. In addition, we explored gender differences in drink driving with provision for the effect of variables such as driving frequency and alcohol consumption. Data were collected via a questionnaire administered to 274 drivers (59.9% females) aged 18-30 years (24.36 ± 2.96). The results obtained with provision for driving frequency revealed substantial differences in driving behaviors between genders. Thus, males were more prone to drink driving, perceived less disapproval by their significant others (parents and peers), and felt less able to avoid drinking-and-driving situations. In addition, they self-reported more frequent alcohol consumption and driving under the influence. The results also confirm the significance of peers' subjective norms and attitudes to drink driving in males. Overconfidence in their own driving skills for driving drunk and perceived behavioral control were found to be significant predictors for drink driving in females. Optimism bias also played a slightly significant role in predicting drink driving but only in females. The important practical implications of these results with a view to designing effective interventions to prevent the risks associated with drink driving in the young population are discussed. Interventions should focus on young people's perceptions of group norms and promoting cautionary driving choices and alternatives to drink driving.

Design optimization of dual-axis driving mechanism for satellite antenna with two planar revolute clearance joints

NASA Astrophysics Data System (ADS)

Bai, Zheng Feng; Zhao, Ji Jun; Chen, Jun; Zhao, Yang

2018-03-01

In the dynamic analysis of satellite antenna dual-axis driving mechanism, it is usually assumed that the joints are ideal or perfect without clearances. However, in reality, clearances in joints are unavoidable due to assemblage, manufacturing errors and wear. When clearance is introduced to the mechanism, it will lead to poor dynamic performances and undesirable vibrations due to impact forces in clearance joint. In this paper, a design optimization method is presented to reduce the undesirable vibrations of satellite antenna considering clearance joints in dual-axis driving mechanism. The contact force model in clearance joint is established using a nonlinear spring-damper model and the friction effect is considered using a modified Coulomb friction model. Firstly, the effects of clearances on dynamic responses of satellite antenna are investigated. Then the optimization method for dynamic design of the dual-axis driving mechanism with clearance is presented. The objective of the optimization is to minimize the maximum absolute vibration peak of antenna acceleration by reducing the impact forces in clearance joint. The main consideration here is to optimize the contact parameters of the joint elements. The contact stiffness coefficient, damping coefficient and the dynamic friction coefficient for clearance joint elements are taken as the optimization variables. A Generalized Reduced Gradient (GRG) algorithm is used to solve this highly nonlinear optimization problem for dual-axis driving mechanism with clearance joints. The results show that the acceleration peaks of satellite antenna and contact forces in clearance joints are reduced obviously after design optimization, which contributes to a better performance of the satellite antenna. Also, the application and limitation of the proposed optimization method are discussed.

Quantifying design trade-offs of beryllium targets on NIF

NASA Astrophysics Data System (ADS)

Yi, S. A.; Zylstra, A. B.; Kline, J. L.; Loomis, E. N.; Kyrala, G. A.; Shah, R. C.; Perry, T. S.; Kanzleiter, R. J.; Batha, S. H.; MacLaren, S. A.; Ralph, J. E.; Masse, L. P.; Salmonson, J. D.; Tipton, R. E.; Callahan, D. A.; Hurricane, O. A.

2017-10-01

An important determinant of target performance is implosion kinetic energy, which scales with the capsule size. The maximum achievable performance for a given laser is thus related to the largest capsule that can be imploded symmetrically, constrained by drive uniformity. A limiting factor for symmetric radiation drive is the ratio of hohlraum to capsule radii, or case-to-capsule ratio (CCR). For a fixed laser energy, a larger hohlraum allows for driving bigger capsules symmetrically at the cost of reduced peak radiation temperature (Tr). Beryllium ablators may thus allow for unique target design trade-offs due to their higher ablation efficiency at lower Tr. By utilizing larger hohlraum sizes than most modern NIF designs, beryllium capsules thus have the potential to operate in unique regions of the target design parameter space. We present design simulations of beryllium targets with a large CCR = 4.3 3.7 . These are scaled surrogates of large hohlraum low Tr beryllium targets, with the goal of quantifying symmetry tunability as a function of CCR. This work performed under the auspices of the U.S. DOE by LANL under contract DE-AC52- 06NA25396, and by LLNL under Contract DE-AC52-07NA27344.

A review of national television PSA campaigns for preventing alcohol-impaired driving, 1987-1992.

PubMed

DeJong, W; Atkin, C K

1995-01-01

We present a content analysis of 137 public service announcements (PSAs) focused on alcohol-impaired driving that aired nationally on U.S. television between 1987 and 1992. Our findings include the following: 1) Most PSAs were intended to reach an undifferentiated general audience, not necessarily those who are at greatest risk for driving after drinking. 2) Most PSAs were designed to create awareness of the problem of alcohol-impaired driving or to promote individual behavior change. 3) More PSAs were developed on the use of designated drivers than on any other subject. 4) About two-thirds of the PSAs included one or more celebrities who speak directly to the audience. Past media campaigns have tended to ignore the fact that people's behavior is profoundly shaped by their environment, which in turn is shaped by public policy. We recommend that future mass media campaigns against alcohol-impaired driving focus on building support for changes in institutional structures, public policy or law that will motivate, support, and sustain the efforts of individuals to alter their behavior. Television PSAs can play an important but somewhat limited role in support of this effort. Greater emphasis will need to be given instead to media advocacy strategies, including paid radio advertising. We further recommend that the principal organizations concerned about alcohol-impaired driving share their plans and develop a common communications strategy that will advance the public policy agenda proposed by the Surgeon General's Workshop on Drunk Driving.

Residual effects of middle-of-the-night administration of zaleplon and zolpidem on driving ability, memory functions, and psychomotor performance.

PubMed

Verster, Joris C; Volkerts, Edmund R; Schreuder, Antonia H C M L; Eijken, Erik J E; van Heuckelum, Janet H G; Veldhuijzen, Dieuwke S; Verbaten, Marinus N; Paty, Isabelle; Darwish, Mona; Danjou, Philippe; Patat, Alain

2002-12-01

Thirty healthy volunteers participated in this two-part study. Part 1 was a single-blind, two-period crossover design to determine the effects of a single dose of ethanol (0.03% < BAC < 0.05%) or ethanol-placebo on driving ability, memory, and psychomotor performance. Part 2 was a double-blind, five-period crossover design to measure the effects of a middle-of-the-night administration of zaleplon 10 or 20 mg, zolpidem 10 or 20 mg, or placebo on driving ability 4 hours after administration and memory and psychomotor performance 6 hours after administration. The on-the-road driving test consisted of operating an instrumented automobile over a 100-km highway circuit at a constant speed (95 km/h) while maintaining a steady lateral position between the right lane boundaries. The standard deviation of lateral position (SDLP) was the primary performance parameter of the driving test. The psychomotor and memory test battery consisted of the Word Learning Test, the Critical Tracking Test, the Divided Attention Test, and the Digit Symbol Substitution Test. Data for each part were analyzed separately using ANOVA for crossover designs. Zaleplon 10 and 20 mg did not significantly impair driving ability 4 hours after middle-of-the-night administration. Relative to placebo, after zolpidem 10 mg, SDLP was significantly elevated, but the magnitude of the difference was small and not likely to be of clinical importance. Memory and psychomotor test performance was unaffected after both doses of zaleplon and zolpidem 10 mg. In contrast, zolpidem 20 mg significantly increased SDLP and speed variability. Further, zolpidem 20 mg significantly impaired performance on all psychomotor and memory tests. Finally, driving performance, Digit Symbol Substitution Test, Divided Attention Test, and immediate and delayed free recall of the Word Learning Test were significantly impaired after ethanol. The results show that zaleplon (10 and 20 mg) is a safe hypnotic devoid of next-morning residual impairment when used in the middle of the night.

Modelling and Simulation in the Design Process of Armored Vehicles

DTIC Science & Technology

2003-03-01

trackway conditions is a demanding optimization task. Basically, a high level of ride comfort requires soft suspension tuning, whereas driving safety relies...The maximum off-road speed is generally limited by traction, input torque, driving safety and ride comfort. When obstacles are to be negotiated, the...wheel travel was defined during the mobility simulation runs. Figure 14: Ramp 1.5m at 40 kph; virtual and physical prototype Driving safety and ride

A new approach to configurable primary data collection.

PubMed

Stanek, J; Babkin, E; Zubov, M

2016-09-01

The formats, semantics and operational rules of data processing tasks in genomics (and health in general) are highly divergent and can rapidly change. In such an environment, the problem of consistent transformation and loading of heterogeneous input data to various target repositories becomes a critical success factor. The objective of the project was to design a new conceptual approach to configurable data transformation, de-identification, and submission of health and genomic data sets. Main motivation was to facilitate automated or human-driven data uploading, as well as consolidation of heterogeneous sources in large genomic or health projects. Modern methods of on-demand specialization of generic software components were applied. For specification of input-output data and required data collection activities, we propose a simple data model of flat tables as well as a domain-oriented graphical interface and portable representation of transformations in XML. Using such methods, the prototype of the Configurable Data Collection System (CDCS) was implemented in Java programming language with Swing graphical interfaces. The core logic of transformations was implemented as a library of reusable plugins. The solution is implemented as a software prototype for a configurable service-oriented system for semi-automatic data collection, transformation, sanitization and safe uploading to heterogeneous data repositories-CDCS. To address the dynamic nature of data schemas and data collection processes, the CDCS prototype facilitates interactive, user-driven configuration of the data collection process and extends basic functionality with a wide range of third-party plugins. Notably, our solution also allows for the reduction of manual data entry for data originally missing in the output data sets. First experiments and feedback from domain experts confirm the prototype is flexible, configurable and extensible; runs well on data owner's systems; and is not dependent on vendor's standards. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Developing User-Driven Climate Information Services to Build Resilience Amongst Groups at Risk of Drought and Flood in Arid and Semi-Arid Land Counties in Kenya

NASA Astrophysics Data System (ADS)

Githungo, W. N.; Shaka, A.; Kniveton, D.; Muithya, L.; Powell, R.; Visman, E. L.

2014-12-01

The Arid and Semi-Arid Land (ASAL) counties of Kitui and Makueni in Kenya are experiencing increasing climate variability in seasonal rainfall, including changes in the onset, cessation and distribution of the two principal rains upon which the majority of the population's small-holder farmers and livestock keepers depend. Food insecurity is prevalent with significant numbers also affected by flooding during periods of intense rainfall. As part of a multi-partner Adaptation Consortium, Kenya Meteorological Services (KMS) are developing Climate Information Services (CIS) which can better support decision making amongst the counties' principal livelihoods groups and across County Government ministries. Building on earlier pilots and stakeholder discussion, the system combines the production of climate information tailored for transmission via regional and local radio stations with the establishment of a new SMS service. SMS are provided through a network of CIS intermediaries drawn from across key government ministries, religious networks, non-governmental and community groups, aiming to achieve one SMS recipient per 3-500 people. It also introduces a demand-led, premium-rate SMS weather information service which is designed to be self-financing in the long term. Supporting the ongoing process of devolution, KMS is downscaling national forecasts for each county, and providing seasonal, monthly, weekly and daily forecasts, as well as warnings of weather-related hazards. Through collaboration with relevant ministries, government bodies and research institutions, including livestock, agriculture, drought management and health, technical advisories are developed to provide guidance on application of the climate information. The system seeks to provide timely, relevant information which can enable people to use weather and climate information to support decisions which protect life and property and build resilience to ongoing climate variability and future change.

“The Heart Game”: Using Gamification as Part of a Telerehabilitation Program for Heart Patients

PubMed Central

Dithmer, Marcus; Grönvall, Erik; Spindler, Helle; Hansen, John; Nielsen, Gitte; Sørensen, Stine Bæk; Dinesen, Birthe

2016-01-01

Abstract Objective: The aim of this article is to describe the development and testing of a prototype application (“The Heart Game”) using gamification principles to assist heart patients in their telerehabilitation process in the Teledialog project. Materials and Methods: A prototype game was developed via user-driven innovation and tested on 10 patients 48–89 years of age and their relatives for a period of 2 weeks. The application consisted of a series of daily challenges given to the patients and relatives and was based on several gamification principles. A triangulation of data collection techniques (interviews, participant observations, focus group interviews, and workshop) was used. Interviews with three healthcare professionals and 10 patients were carried out over a period of 2 weeks in order to evaluate the use of the prototype. Results: The heart patients reported the application to be a useful tool as a part of their telerehabilitation process in everyday life. Gamification and gameful design principles such as leaderboards, relationships, and achievements engaged the patients and relatives. The inclusion of a close relative in the game motivated the patients to perform rehabilitation activities. Conclusions: “The Heart Game” concept presents a new way to motivate heart patients by using technology as a social and active approach to telerehabilitation. The findings show the potential of using gamification for heart patients as part of a telerehabilitation program. The evaluation indicated that the inclusion of the patient's spouse in the rehabilitation activities could be an effective strategy. A major challenge in using gamification for heart patients is avoiding a sense of defeat while still adjusting the level of difficulty to the individual patient. PMID:26579590

Study protocol for a cluster randomised controlled trial to assess the effectiveness of user-driven intervention to prevent aggressive events in psychiatric services.

PubMed

Välimäki, Maritta; Yang, Min; Normand, Sharon-Lise; Lorig, Kate R; Anttila, Minna; Lantta, Tella; Pekurinen, Virve; Adams, Clive E

2017-04-04

People admitted to psychiatric hospitals with a diagnosis of schizophrenia may display behavioural problems. These may require management approaches such as use of coercive practices, which impact the well-being of staff members, visiting families and friends, peers, as well as patients themselves. Studies have proposed that not only patients' conditions, but also treatment environment and ward culture may affect patients' behaviour. Seclusion and restraint could possibly be prevented with staff education about user-centred, more humane approaches. Staff education could also increase collaboration between patients, family members and staff, which may further positively affect treatment culture and lower the need for using coercive treatment methods. This is a single-blind, two-arm cluster randomised controlled trial involving 28 psychiatric hospital wards across Finland. Units will be randomised to receive either a staff educational programme delivered by the team of researchers, or standard care. The primary outcome is the incidence of use of patient seclusion rooms, assessed from the local/national health registers. Secondary outcomes include use of other coercive methods (limb restraint, forced injection, and physical restraint), service use, treatment satisfaction, general functioning among patients, and team climate and employee turn-over (nursing staff). The study, designed in close collaboration with staff members, patients and their relatives, will provide evidence for a co-operative and user-centred educational intervention aiming to decrease the prevalence of coercive methods and service use in the units, increase the functional status of patients and improve team climate in the units. We have identified no similar trials. ClinicalTrials.gov NCT02724748 . Registered on 25 th of April 2016.

VIEW LOOKING NORTHEAST FROM A POINT NEAR THE CIRCULAR DRIVE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW LOOKING NORTHEAST FROM A POINT NEAR THE CIRCULAR DRIVE ALONG THE PRINCIPAL AXIS THROUGH SECTION F. THOMAS U. WALTER PROVIDED THE WOODLANDS CEMETERY WITH A DESIGN FOR SECTION F’S LAYOUT IN 1846 - Woodlands Cemetery, 4000 Woodlands Avenue, Philadelphia, Philadelphia County, PA

Use of pile driving analysis for assessment of axial load capacity of piles.

DOT National Transportation Integrated Search

2012-05-01

Driven piles are commonly used in foundation engineering. Pile driving formulae, which directly relate the pile set per blow : to the capacity of the pile, are commonly used to decide whether an installed pile will have the designed capacity. However...

Use of Pile Driving Analysis for Assessment of Axial Load Capacity of Piles

DOT National Transportation Integrated Search

2012-05-01

Driven piles are commonly used in foundation engineering. Pile driving formulae, which directly relate the pile set per blow : to the capacity of the pile, are commonly used to decide whether an installed pile will have the designed capacity. However...

Evaluation of seven publicized enforcement demonstration programs to reduce impaired driving : Georgia, Louisiana, Pennsylvania, Tennessee, Texas, Indiana, and Michigan

DOT National Transportation Integrated Search

2008-02-01

Between 2000 and 2003, the National Highway Traffic Safety Administration funded seven alcohol demonstration projects designed to reduce impaired driving through well-publicized and highly visible enforcement. The projects were conducted in seven Sta...

Oregon Department of Transportation greenroads pilot project : US 97 : Lava Butte-S. Century Drive section.

DOT National Transportation Integrated Search

2011-02-01

This project is a Greenroads Pilot Project on the Oregon Department of Transportation (ODOT) project "US 97: Lava Butte S. : Century Drive Section." Greenroads is a sustainability rating system for roadway design and construction (a complete desc...

Design and analysis of a new high frequency double-servo direct drive rotary valve

NASA Astrophysics Data System (ADS)

Zhu, Muzhi; Zhao, Shengdun; Li, Jingxiang

2016-12-01

Researchers have investigated direct drive valve for many years to solve problems, such as fluid force imbalance and switching frequency. The structure of the rotary valve has received considerable research interest because of its favorable dynamic properties and simple structure. This paper studied the high frequency doubleservo direct drive rotary valve (DDRV), and proposed a novel structure and drive method satisfying high reversing frequency and adequate quantity of flow. Servo motors are integrated into the valve by the innovative structure, which is designed to equilibrate the unbalanced radial fluid force with the symmetric distributed oil ports. Aside from the fast reversing function of the valve, the DDRV presented high performance in linearity of the flow quantity and valve opening as a result of the fan-shaped flow ports. In addition, a computational fluid dynamics (CFD) method based on Fluent was conducted to verify the flux regulation effect of the height change of the adjustable boss.

Resonant-Type Smooth Impact Drive Mechanism Actuator Operating at Lower Input Voltages

NASA Astrophysics Data System (ADS)

Morita, Takeshi; Nishimura, Takuma; Yoshida, Ryuichi; Hosaka, Hiroshi

2013-07-01

We report on the design and fabrication of a resonant-type smooth impact drive mechanism (SIDM) actuator based on a multilayered piezoelectric ceramic transducer. Conventional SIDMs use off-resonant sawtooth-shaped displacement in developing stick-slip motion of a slider, but require large input voltages for high-speed operation. In contrast, in resonant-type SIDMs, a quasi-sawtooth-shaped displacement is obtained by combining two resonant vibrational modes. This driving principle enables low input voltage operations. In combining the modes, their frequency ratio must be 1:2. To design and optimize the stator transducer to generate sawtooth-shaped displacements, a transfer matrix method was adopted. With a preload of 270 mN, the no-load speed was 40 mm/s under a driving voltage of 1.6 V (peak to peak). This input voltage was one-sixth that of previous SIDMs for the same performance. Concurrently, heat generation was significantly reduced because dielectric losses were suppressed under the lower input voltage operation.

Design of Range Adaptive Wireless Power Transfer System Using Non-coaxial Coils

NASA Astrophysics Data System (ADS)

Yang, Dongsheng; Won, Sokhui; Hong, Huan

2017-05-01

Wireless Power Transfer (WPT) is a remarkable technology because of its convenience and applicability in harsh environment. Particularly, Magnetic Coupling WPT (MC-WPT) is a proper method to midrange power transfer, but the frequency splitting at over-coupling range, which is related with transfer distance, is challenge of transmission efficiency. In order to overcome this phenomenon, recently the range adaptive WPT is proposed. In this paper, we aim to the type with a set of non-coaxial driving coils, so that this may remove the connection wires from PA (Power Amplifier) to driving coil. And, when the radius of driving coil is changed, on the different gaps between driving and TX coils, coupling coefficient between these is computed in both cases of coaxial and non-coaxial configurations. In addition, the designing steps for 4-coil WPT system using non-coaxial coils are described with the example. Finally, the reliability of this topology has been proved and simulated with PSPICE.

Synthetic Fiber Capstan Drives for Highly Efficient, Torque Controlled, Robotic Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mazumdar, Anirban; Spencer, Steven James; Hobart, Clinton

Here this paper describes the design and performance of a synthetic rope on sheave drive system. This system uses synthetic ropes instead of steel cables to achieve low weight and a compact form factor. We demonstrate how this system is capable of 28-Hz torque control bandwidth, 95% efficiency, and quiet operation, making it ideal for use on legged robots and other dynamic physically interactive systems. Component geometry and tailored maintenance procedures are used to achieve high endurance. Endurance tests based on walking data predict that the ropes will survive roughly 247,000 cycles when used on large (90 kg), fully actuatedmore » bipedal robot systems. The drive systems have been incorporated into two novel bipedal robots capable of three-dimensional unsupported walking. Robot data illustrate effective torque tracking and nearly silent operation. Finally, comparisons with alternative transmission designs illustrate the size, weight, and endurance advantages of using this type of synthetic rope drive system.« less

Synthetic Fiber Capstan Drives for Highly Efficient, Torque Controlled, Robotic Applications

DOE PAGES

Mazumdar, Anirban; Spencer, Steven James; Hobart, Clinton; ...

2017-01-05

Here this paper describes the design and performance of a synthetic rope on sheave drive system. This system uses synthetic ropes instead of steel cables to achieve low weight and a compact form factor. We demonstrate how this system is capable of 28-Hz torque control bandwidth, 95% efficiency, and quiet operation, making it ideal for use on legged robots and other dynamic physically interactive systems. Component geometry and tailored maintenance procedures are used to achieve high endurance. Endurance tests based on walking data predict that the ropes will survive roughly 247,000 cycles when used on large (90 kg), fully actuatedmore » bipedal robot systems. The drive systems have been incorporated into two novel bipedal robots capable of three-dimensional unsupported walking. Robot data illustrate effective torque tracking and nearly silent operation. Finally, comparisons with alternative transmission designs illustrate the size, weight, and endurance advantages of using this type of synthetic rope drive system.« less

Impact of sleep deprivation and obstructive sleep apnea syndrome on daytime vigilance and driving performance: a laboratory perspective.

PubMed

Pizza, F; Contardi, S; Mondini, S; Cirignotta, F

2012-01-01

To study the impact of sleepiness, a well-established cause of car accidents, on driving ability, we designed a 30-min monotonous simulated driving task. Our simulated driving task encompasses both primary vehicle control (standard deviation of lane position, crash occurrence) and secondary tasks (type and reaction times to divided attention tasks). Driving simulator data were correlated to subjective (state/trait) and objective (MSLT/MWT) sleepiness measures in healthy subjects undergoing sleep deprivation (SD) and in obstructive sleep apnea (OSAS) patients. SD induced severe sleepiness during nighttime, when state sleepiness increased while primary vehicle control ability worsened. After SD, driving ability decreased and was inversely correlated to subjective and objective sleepiness at MSLT. OSAS patients driving ability was well correlated to objective sleepiness, with inverse correlation to sleep propensity at the MSLT and even more strict relation with the ability to maintain wakefulness at the MWT. Sleepiness worsens driving ability in healthy subjects after SD and in OSAS patients. Driving ability correlates with subjective and objective sleepiness measures, in particular to the ability to maintain wakefulness.

A comparison of the combined-use of alcohol & energy drinks to alcohol-only on high-risk drinking and driving behaviors.

PubMed

Woolsey, Conrad L; Jacobson, Bert H; Williams, Ronald D; Barry, Adam E; Davidson, Robert T; Evans, Marion W; Beck, Niels C

2015-01-01

The combined-use of alcohol and energy drinks is an emerging public health issue. This investigation examined differences in drinking and driving behaviors among combined-users (CU) and participants who consumed alcohol-only (AO). This study was specifically designed to investigate potential differences in drinker's perceptions of (a) what it means to them to drive over the .08 Blood Alcohol Content (BAC) driving limit and (b) what it means to drive after knowing they have had too much to drink to drive safely. College students (N = 355) were surveyed to assess differences in drinking and driving-related behaviors between the AO (n = 174) and CU (n = 107) groups. CU were more likely than AO to drive over the .08 BAC driving limit (53% vs. 38%; p = .009) and after knowing they were too drunk to drive (57% vs. 44%; p = .025). CU were also more likely (56% vs. 35%; p = .000) to ride with an intoxicated driver while knowing it was unsafe. Conclusions/Importance: Combined-users are more likely to drive after drinking, drive while knowingly drunk, and participate in other high-risk behaviors such as heavy drinking that increase the potential for injury. Public policy makers and health professionals should focus prevention efforts to reduce high-risk combined-use behavior.

Estimation of the Driving Style Based on the Users’ Activity and Environment Influence

PubMed Central

Sysoev, Mikhail; Kos, Andrej; Guna, Jože; Pogačnik, Matevž

2017-01-01

New models and methods have been designed to predict the influence of the user’s environment and activity information to the driving style in standard automotive environments. For these purposes, an experiment was conducted providing two types of analysis: (i) the evaluation of a self-assessment of the driving style; (ii) the prediction of aggressive driving style based on drivers’ activity and environment parameters. Sixty seven h of driving data from 10 drivers were collected for analysis in this study. The new parameters used in the experiment are the car door opening and closing manner, which were applied to improve the prediction accuracy. An Android application called Sensoric was developed to collect low-level smartphone data about the users’ activity. The driving style was predicted from the user’s environment and activity data collected before driving. The prediction was tested against the actual driving style, calculated from objective driving data. The prediction has shown encouraging results, with precision values ranging from 0.727 up to 0.909 for aggressive driving recognition rate. The obtained results lend support to the hypothesis that user’s environment and activity data could be used for the prediction of the aggressive driving style in advance, before the driving starts. PMID:29065476

Magnetic Gearing Versus Conventional Gearing in Actuators for Aerospace Applications

NASA Technical Reports Server (NTRS)

Puchhammer, Gregor

2014-01-01

Magnetic geared actuators (MGA) are designed to perform highly reliable, robust and precise motion on satellite platforms or aerospace vehicles. The design allows MGA to be used for various tasks in space applications. In contrast to conventional geared drives, the contact and lubrication free force transmitting elements lead to a considerable lifetime and range extension of drive systems. This paper describes the fundamentals of magnetic wobbling gears (MWG) and the deduced inherent characteristics, and compares conventional and magnetic gearing.

The advanced hohlraum research project

NASA Astrophysics Data System (ADS)

Jones, Ogden; Tabak, M.; Amendt, P. A.; Hammer, J. H.; Baker, K. L.; Baumann, T. F.; Berger, R. L.; Biener, M. M.; Ho, D. D.; Kim, S. H.; Logan, B. G.; Mariscal, D. A.; Patankar, S.; Wallace, R. L.

2017-10-01

We present results of a three-year study on alternate hohlraum designs. Several alternatives to cylindrical gas-filled hohlraums have been investigated. Proposed new hohlraum concepts utilize different hohlraum shapes, multiple laser entrance holes, and alternate materials such as metal foam walls. For each design we assess the radiation drive efficiency, the time-dependent drive symmetry, and laser-plasma interaction issues such as backscatter and crossed beam energy transfer. Results from supporting experiments on laser-heated foams are also summarized. Prepared by LLNL under LDRD 15-ERD-058.

Experimental Evaluation of Turning Vane Designs for High-speed and Coupled Fan-drive Corners of 0.1-scale Model of NASA Lewis Research Center's Proposed Altitude Wind Tunnel

NASA Technical Reports Server (NTRS)

Gelder, Thomas F.; Moore, Royce D.; Shyne, Rickey J.; Boldman, Donald R.

1987-01-01

Two turning vane designs were experimentally evaluated for the fan-drive corner (corner 2) coupled to an upstream diffuser and the high-speed corner (corner 1) of the 0.1 scale model of NASA Lewis Research Center's proposed Altitude Wind Tunnel. For corner 2 both a controlled-diffusion vane design (vane A4) and a circular-arc vane design (vane B) were studied. The corner 2 total pressure loss coefficient was about 0.12 with either vane design. This was about 25 percent less loss than when corner 2 was tested alone. Although the vane A4 design has the advantage of 20 percent fewer vanes than the vane B design, its vane shape is more complex. The effects of simulated inlet flow distortion on the overall losses for corner 1 or 2 were small.

Traction Drives for Zero Stick-Slip Robots, and Reaction Free, Momentum Balanced Systems

NASA Technical Reports Server (NTRS)

Anderson, William J.; Shipitalo, William; Newman, Wyatt

1995-01-01

Two differential (dual input, single output) drives (a roller-gear and a pure roller), and a momentum balanced (single input, dual output) drive (pure roller ) were designed, fabricated, and tested. The differential drives are each rated at 295 rad/sec (2800 rpm) input speed, 450 N-m (4,000 in-lbf) output torque. The momentum balanced drive is rated at 302 rad/sec (2880 rpm) input speed, and dual output torques of 434N-m (3840 in-lbf). The Dual Input Differential Roller-Gear Drive (DC-700) has a planetary roller-gear system with a reduction ratio (one input driving the output with the second input fixed) of 29.23: 1. The Dual Input Differential Roller Drive (DC-500) has a planetary roller system with a reduction ratio of approximately 24:1. Each of the differential drives features dual roller-gear or roller arrangements consisting of a sun, four first row planets, four second row planets, and a ring. The Momentum Balanced (Grounded Ring) Drive (DC-400) has a planetary roller system with a reduction ratio of 24:1 with both outputs counterrotating at equal speed. Its single roller cluster consists of a sun, five first and five second row planets, a roller cage or spider and a ring. Outputs are taken from both the roller cage and the ring which counterrotate. Test results reported for all three drives include angular and torque ripple (linearity and cogging), viscous and Coulomb friction, and forward and reverse power efficiency. Of the two differential drives, the Differential Roller Drive had better linearity and less cogging than did the Differential Roller-Gear Drive, but it had higher friction and lower efficiency (particularly at low power throughput levels). Use of full preloading rather than a variable preload system in the Differential Roller Drive assessed a heavy penalty in part load efficiency. Maximum measured efficiency (ratio of power out to power in) was 95% for the Differential Roller-Gear Drive and 86% for the Differential Roller Drive. The Momentum Balanced (Grounded Ring) Drive performed as expected kinematically. Reduction r-atios to the two counterrotating outputs (design nominal=24:1) were measured to be 23.98:1 and 24.12:1 at zero load.. At 25ONm (2200 in-lbf) output torque the ratio changed 2% due to roller creep. This drive was the smoothest of all three as determined from linearity and cogging tests, and maximum measured efficiency (ratio of power out to power in) was 95%. The disadvantages of full preloading as comvared to variable preload were apparent in this drive as in the Differential Roller Drive. Efficiencies at part load were low, but improved dramatically with increases in torque. These were consistent with friction measurements which indicated losses primarily from Coulomb friction. The initial preload level setting was low so roller slip was encountered at higher torques during testing.

Drive Control System for Pipeline Crawl Robot Based on CAN Bus

NASA Astrophysics Data System (ADS)

Chen, H. J.; Gao, B. T.; Zhang, X. H.; Deng2, Z. Q.

2006-10-01

Drive control system plays important roles in pipeline robot. In order to inspect the flaw and corrosion of seabed crude oil pipeline, an original mobile pipeline robot with crawler drive unit, power and monitor unit, central control unit, and ultrasonic wave inspection device is developed. The CAN bus connects these different function units and presents a reliable information channel. Considering the limited space, a compact hardware system is designed based on an ARM processor with two CAN controllers. With made-to-order CAN protocol for the crawl robot, an intelligent drive control system is developed. The implementation of the crawl robot demonstrates that the presented drive control scheme can meet the motion control requirements of the underwater pipeline crawl robot.

Transmission control unit drive based on the AUTOSAR standard

NASA Astrophysics Data System (ADS)

Guo, Xiucai; Qin, Zhen

2018-03-01

It is a trend of automotive electronics industry in the future that automotive electronics embedded system development based on the AUTOSAR standard. AUTOSAR automotive architecture standard has proposed the transmission control unit (TCU) development architecture and designed its interfaces and configurations in detail. This essay has discussed that how to drive the TCU based on AUTOSAR standard architecture. The results show that driving the TCU with the AUTOSAR system improves reliability and shortens development cycles.

Development of a Drilling Fluid Drive Downhole Tractor in Oil Field

NASA Astrophysics Data System (ADS)

Fang, Delei; Shang, Jianzhong; Liu, Yiying; Wu, Wei; Luo, Zirong

2018-01-01

This paper proposes a drilling fluid drive downhole tractor, which has the advantages of compact structure, large traction, fast speed and high reliability. The overall mechanical structure of the tractor is introduced, the concrete structures including supporting structure and cushion mechanism are designed. And its all-hydraulic drive continuous propulsion principle is analyzed. Finally the simulation analysis of the tractor operation is carried out to prove that the traction motion scheme is feasible.

Development and test of a motivational approach and materials for increasing use of restraints.

DOT National Transportation Integrated Search

1982-03-01

The objective of this study was to design and assess the effect of : a motivational approach to modify the riding and driving public's attitudes towards : the perceived risks of driving an automobile and the use of occupant restraint systems. : Two h...

A High Fidelity Driving Simulator as a Tool for Design and Evaluation of Highway Infrastructure Upgrades

DOT National Transportation Integrated Search

2007-05-01

A rapid prototyping approach was used in the driving simulation laboratory at the Western Transportation Institute (WTI) to simulate approximately 22 miles of US 191 between the Big Sky Resort community and the northern mouth of the Gallatin Canyon. ...

Handbook of Research on Driving STEM Learning with Educational Technologies

ERIC Educational Resources Information Center

Ramírez-Montoya, María-Soledad, Ed.

2017-01-01

Educational strategies have evolved over the years, due to research breakthroughs and the application of technology. By using the latest learning innovations, curriculum and instructional design can be enhanced and strengthened. The "Handbook of Research on Driving STEM Learning with Educational Technologies" is an authoritative…

An analysis of crash likelihood : age versus driving experience

DOT National Transportation Integrated Search

1995-05-01

The study was designed to determine the crash likelihood of drivers in Michigan as a function of two independent variables: driver age and driving experience. The age variable had eight levels (18, 19, 20, 21, 22, 23, 24, and 25 years old) and the ex...

A Roadmap for Interpreting the Literature on Vision and Driving

PubMed Central

Owsley, Cynthia; Wood, Joanne M.; McGwin, Gerald

2015-01-01

Over the past several decades there has been a sharp increase in the number of studies focused on the relationship between vision and driving. The intensified scientific attention to this topic has most likely been stimulated by the lack of an evidence-basis for determining vision standards for driving licensure and a poor understanding about how vision impairment impacts driver safety and performance. Clinicians depend on the scientific literature on vision and driving as a resource to appropriately advise visually impaired patients about driving fitness. Policy makers also depend on the scientific literature in order to develop guidelines that are evidence-based and are thus fair to persons who are visually impaired. Thus it is important for clinicians and policy makers alike to understand how various study designs and measurement methods should be appropriately interpreted so that the conclusions and recommendations they make based on this literature are not overly broad, too narrowly constrained, or even misguided. In this overview, based on our 25 years of experience in this field, we offer a methodological framework to guide interpretations of studies on vision and driving, which can also serve as a heuristic for researchers in the area. Here we discuss research designs and general measurement methods for the study of vision as they relate to driver safety, driver performance, and driver-centered (self-reported) outcomes. PMID:25753389

Pulsed Eddy Current Probe Design Based on Transient Circuit Analysis

NASA Astrophysics Data System (ADS)

Cadeau, Trevor J.; Krause, Thomas W.

2009-03-01

Probe design parameters affecting depth of penetration of pulsed eddy currents in multi-layer aluminum 2024-T3 were examined. Several probe designs were evaluated for their ability to detect a discontinuity at the bottom of a stack of aluminum plates. The reflection type probes, consisting of pick-up coil and encircling drive coil, were characterized based on their transient response to a square pulse excitation. Probes with longer fundamental time constants, equivalent to a lower driving frequency, generated greater depth of penetration. However, additional factors such as inductive and resistive load, and excessive coil heating were also factors that limited signal-to-noise response with increasing layer thickness.

Design and experiment of a neural signal detection using a FES driving system.

PubMed

Zonghao, Huang; Zhigong, Wang; Xiaoying, Lu; Wenyuan, Li; Xiaoyan, Shen; Xintai, Zhao; Shushan, Xie; Haixian, Pan; Cunliang, Zhu

2010-01-01

The channel bridging, signal regenerating, and functional rebuilding of injured nerves is one of the most important issues in life science research. In recent years, some progresses in the research area have been made in repairing injured nerves with microelectronic neural bridge. Based on the previous work, this paper presents a neural signal detection and functional electrical stimulation (FES) driving system with using high performance operational amplifiers, which has been realized. The experimental results show that the designed system meets requirements. In animal experiments, sciatic nerve signal detection, regeneration and function rebuilding between two toads have been accomplished successfully by using the designed system.

AlliedSignal driver's viewer enhancement (DVE) for paramilitary and commercial applications

NASA Astrophysics Data System (ADS)

Emanuel, Michael; Caron, Hubert; Kovacevic, Branislav; Faina-Cherkaoui, Marcela; Wrobel, Leslie; Turcotte, Gilles

1999-07-01

AlliedSignal Driver's Viewer Enhancement (DVE) system is a thermal imager using a 320 X 240 uncooled microbolometer array. This high performance system was initially developed for military combat and tactical wheeled vehicles. It features a very small sensor head remotely mounted from the display, control and processing module. The sensor head has a modular design and is being adapted to various commercial applications such as truck and car-driving aid, using specifically designed low cost optics. Tradeoffs in the system design, system features and test results are discussed in this paper. A short video shows footage of the DVE system while driving at night.

Mine Winder Drives in Integrated Copper Complex

NASA Astrophysics Data System (ADS)

Dey, Pranab Kumar

2018-04-01

This paper describes various features required to be evaluated before selecting mine winder drives. In handling such project, the selection of proper equipments is necessary at the initial design stage of planning and how the electrical system design considers all aspects to protect the grid from unwarranted influence of the connected loads and minimize the generation of harmonics due to network configurations adopted to keep it within the stipulated value dictated by the supply authorities has been discussed. The design should cover all aspects to provide quality power with effective braking system required as per the mining statute for operational safety. It also emphasizes on the requirement of quality maintenance.

The effect on teen driving outcomes of the Checkpoints Program in a state-wide trial.

PubMed

Simons-Morton, Bruce G; L Hartos, Jessica; Leaf, William A; Preusser, David F

2006-09-01

Crash rates among teenagers are highly elevated during the first months of licensure. Parent-imposed driving restrictions on initial driving privileges can reduce exposure to high-risk driving conditions, thus reducing crash risk while teens' driving proficiency develops. This report describes the effect of the Checkpoints Program on driving limits and outcomes. Connecticut teens who obtained a learners permit over a 9-month period were recruited, providing a final sample of 3743 who obtained driver licenses. Families were randomized to the intervention or comparison condition. Intervention families received by mail a series of persuasive communications related to high-risk teen driving and a parent-teen driving agreement, while comparison families received on the same schedule general information on driving and vehicle maintenance. Relative to the comparison group, teens and parents in the Checkpoints Program reported significantly greater limits on high-risk teen driving conditions at licensure, 3-, and 6-months post-licensure; and intervention teens reported significantly less risky driving at each reporting period. By the 12-month follow up teens in the intervention group were significantly less likely than those in the comparison group to have had a traffic violation. However, no treatment group effect was found for crashes. This is the first study to report significant effects on teen driving behavior and performance of education designed to increase parental-imposed teen driving limits.

Design and Performance Analysis of an Intrinsically Safe Ultrasonic Ranging Sensor

PubMed Central

Zhang, Hongjuan; Wang, Yu; Zhang, Xu; Wang, Dong; Jin, Baoquan

2016-01-01

In flammable or explosive environments, an ultrasonic sensor for distance measurement poses an important engineering safety challenge, because the driving circuit uses an intermediate frequency transformer as an impedance transformation element, in which the produced heat or spark is available for ignition. In this paper, an intrinsically safe ultrasonic ranging sensor is designed and implemented. The waterproof piezoelectric transducer with integrated transceiver is chosen as an energy transducing element. Then a novel transducer driving circuit is designed based on an impedance matching method considering safety spark parameters to replace an intermediate frequency transformer. Then, an energy limiting circuit is developed to achieve dual levels of over-voltage and over-current protection. The detail calculation and evaluation are executed and the electrical characteristics are analyzed to verify the intrinsic safety of the driving circuit. Finally, an experimental platform of the ultrasonic ranging sensor system is constructed, which involves short-circuit protection. Experimental results show that the proposed ultrasonic ranging sensor is excellent in both ranging performance and intrinsic safety. PMID:27304958

Power-Quality Improvement in PFC Bridgeless SEPIC-Fed BLDC Motor Drive

NASA Astrophysics Data System (ADS)

Singh, Bhim; Bist, Vashist

2013-06-01

This article presents a design of a power factor correction (PFC)-based brushless DC (BLDC) motor drive. The speed control of BLDC motor is achieved by controlling the DC link voltage of the voltage source inverter (VSI) feeding BLDC motor using a single voltage sensor. A front-end bridgeless single-ended primary inductance converter (SEPIC) is used for DC link voltage control and PFC operation. A bridgeless SEPIC is designed to operate in discontinuous inductor current mode (DICM) thus utilizing a simple control scheme of voltage follower. An electronic commutation of BLDC motor is used for VSI to operate in a low-frequency operation for reduced switching losses in the VSI. Moreover, a bridgeless topology offers less conduction losses due to absence of diode bridge rectifier for further increasing the efficiency. The proposed BLDC motor drive is designed to operate over a wide range of speed control with an improved power-quality at the AC mains under the recommended international power-quality standards such as IEC 61000-3-2.

Design and Performance Analysis of an Intrinsically Safe Ultrasonic Ranging Sensor.

PubMed

Zhang, Hongjuan; Wang, Yu; Zhang, Xu; Wang, Dong; Jin, Baoquan

2016-06-13

In flammable or explosive environments, an ultrasonic sensor for distance measurement poses an important engineering safety challenge, because the driving circuit uses an intermediate frequency transformer as an impedance transformation element, in which the produced heat or spark is available for ignition. In this paper, an intrinsically safe ultrasonic ranging sensor is designed and implemented. The waterproof piezoelectric transducer with integrated transceiver is chosen as an energy transducing element. Then a novel transducer driving circuit is designed based on an impedance matching method considering safety spark parameters to replace an intermediate frequency transformer. Then, an energy limiting circuit is developed to achieve dual levels of over-voltage and over-current protection. The detail calculation and evaluation are executed and the electrical characteristics are analyzed to verify the intrinsic safety of the driving circuit. Finally, an experimental platform of the ultrasonic ranging sensor system is constructed, which involves short-circuit protection. Experimental results show that the proposed ultrasonic ranging sensor is excellent in both ranging performance and intrinsic safety.

Preliminary Design and Investigation of Integrated Compressor with Composite Material Wheel

NASA Astrophysics Data System (ADS)

Wang, Jifeng; Müller, Norbert

2012-06-01

An integrated water vapor compressor with composite material wheel is developed and strength analysis using FEM is presented. The design of wound composite material allows for integrating all rotating parts of the drive that may simply reduce to only the rotor of the electrical motor, since no drive shaft is required anymore. This design can reduce the number of parts and mass, which is convenient for engineers to maintain the compressor. The electrical motors are brushless DC motors operating through a frequency drive and apply a torque on the wheels through the materials bonded in the wheel shrouds. This system allows a large amount of compression to be produced in a multi-stage compression setup. To determine the stress and vibration characteristics of this integrated compressor, numerical analysis is carried out using FEM. The simulation result shows that the integrated compressor with composite material wheel can be used in a chiller system where water as a refrigerant.

A novel robust speed controller scheme for PMBLDC motor.

PubMed

Thirusakthimurugan, P; Dananjayan, P

2007-10-01

The design of speed and position controllers for permanent magnet brushless DC motor (PMBLDC) drive remains as an open problem in the field of motor drives. A precise speed control of PMBLDC motor is complex due to nonlinear coupling between winding currents and rotor speed. In addition, the nonlinearity present in the developed torque due to magnetic saturation of the rotor further complicates this issue. This paper presents a novel control scheme to the conventional PMBLDC motor drive, which aims at improving the robustness by complete decoupling of the design besides minimizing the mutual influence among the speed and current control loops. The interesting feature of this robust control scheme is its suitability for both static and dynamic aspects. The effectiveness of the proposed robust speed control scheme is verified through simulations.

Control of adaptive optic element displacement with the help of a magnetic rheology drive

NASA Astrophysics Data System (ADS)

Deulin, Eugeni A.; Mikhailov, Valeri P.; Sytchev, Victor V.

2000-10-01

The control system of adaptive optic of a large astronomical segmentated telescope was designed and tested. The dynamic model and the amplitude-frequency analysis of the new magnetic rheology (MR) drive are presented. The loop controlled drive consists of hydrostatic carrier, MR hydraulic loop controlling system, elastic thin wall seal, stainless seal which are united in a single three coordinate manipulator. This combination ensures short positioning error (delta) (phi)

WebGL Visualisation of 3D Environmental Models Based on Finnish Open Geospatial Data Sets

NASA Astrophysics Data System (ADS)

Krooks, A.; Kahkonen, J.; Lehto, L.; Latvala, P.; Karjalainen, M.; Honkavaara, E.

2014-08-01

Recent developments in spatial data infrastructures have enabled real time GIS analysis and visualization using open input data sources and service interfaces. In this study we present a new concept where metric point clouds derived from national open airborne laser scanning (ALS) and photogrammetric image data are processed, analyzed, finally visualised a through open service interfaces to produce user-driven analysis products from targeted areas. The concept is demonstrated in three environmental applications: assessment of forest storm damages, assessment of volumetric changes in open pit mine and 3D city model visualization. One of the main objectives was to study the usability and requirements of national level photogrammetric imagery in these applications. The results demonstrated that user driven 3D geospatial analyses were possible with the proposed approach and current technology, for instance, the landowner could assess the amount of fallen trees within his property borders after a storm easily using any web browser. On the other hand, our study indicated that there are still many uncertainties especially due to the insufficient standardization of photogrammetric products and processes and their quality indicators.

Contextual Compression of Large-Scale Wind Turbine Array Simulations: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gruchalla, Kenny M; Brunhart-Lupo, Nicholas J; Potter, Kristin C

Data sizes are becoming a critical issue particularly for HPC applications. We have developed a user-driven lossy wavelet-based storage model to facilitate the analysis and visualization of large-scale wind turbine array simulations. The model stores data as heterogeneous blocks of wavelet coefficients, providing high-fidelity access to user-defined data regions believed the most salient, while providing lower-fidelity access to less salient regions on a block-by-block basis. In practice, by retaining the wavelet coefficients as a function of feature saliency, we have seen data reductions in excess of 94 percent, while retaining lossless information in the turbine-wake regions most critical to analysismore » and providing enough (low-fidelity) contextual information in the upper atmosphere to track incoming coherent turbulent structures. Our contextual wavelet compression approach has allowed us to deliver interactive visual analysis while providing the user control over where data loss, and thus reduction in accuracy, in the analysis occurs. We argue this reduced but contexualized representation is a valid approach and encourages contextual data management.« less

Contextual Compression of Large-Scale Wind Turbine Array Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gruchalla, Kenny M; Brunhart-Lupo, Nicholas J; Potter, Kristin C

Data sizes are becoming a critical issue particularly for HPC applications. We have developed a user-driven lossy wavelet-based storage model to facilitate the analysis and visualization of large-scale wind turbine array simulations. The model stores data as heterogeneous blocks of wavelet coefficients, providing high-fidelity access to user-defined data regions believed the most salient, while providing lower-fidelity access to less salient regions on a block-by-block basis. In practice, by retaining the wavelet coefficients as a function of feature saliency, we have seen data reductions in excess of 94 percent, while retaining lossless information in the turbine-wake regions most critical to analysismore » and providing enough (low-fidelity) contextual information in the upper atmosphere to track incoming coherent turbulent structures. Our contextual wavelet compression approach has allowed us to deliver interative visual analysis while providing the user control over where data loss, and thus reduction in accuracy, in the analysis occurs. We argue this reduced but contextualized representation is a valid approach and encourages contextual data management.« less

Produsage as a form of self-publication. A qualitative study of casual news produsage

NASA Astrophysics Data System (ADS)

Picone, Ike

2011-04-01

While Axel Bruns's theory of produsage offers an adequate way of looking at a variety of sites where the production of news content takes the form of collaborative, user-driven production, it seems less suited for the study of productive news use as a user experience, as a way users engage in a more productive way with content. This article gives a first impetus towards the expansion of the theory of produsage to a more user-oriented framework that is fitted to approach produsage as a social practice, rather than as a process of information production. The empirical work presented in this paper concerns the average news user, rather than the expert bloggers and citizen journalists most studies tend to focus on. Through a qualitative, semi-experimental study based on a Living Lab-approach, motivational, situational, and social factors shaping productive news use are identified. Drawing from the findings, conceptual elements as "potential public" and "social reflex" are introduced. Self-publication is proposed as a way to understand how average news users experience productive news use.

Geospatial Optimization of Siting Large-Scale Solar Projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macknick, Jordan; Quinby, Ted; Caulfield, Emmet

2014-03-01

Recent policy and economic conditions have encouraged a renewed interest in developing large-scale solar projects in the U.S. Southwest. However, siting large-scale solar projects is complex. In addition to the quality of the solar resource, solar developers must take into consideration many environmental, social, and economic factors when evaluating a potential site. This report describes a proof-of-concept, Web-based Geographical Information Systems (GIS) tool that evaluates multiple user-defined criteria in an optimization algorithm to inform discussions and decisions regarding the locations of utility-scale solar projects. Existing siting recommendations for large-scale solar projects from governmental and non-governmental organizations are not consistent withmore » each other, are often not transparent in methods, and do not take into consideration the differing priorities of stakeholders. The siting assistance GIS tool we have developed improves upon the existing siting guidelines by being user-driven, transparent, interactive, capable of incorporating multiple criteria, and flexible. This work provides the foundation for a dynamic siting assistance tool that can greatly facilitate siting decisions among multiple stakeholders.« less

Exploration of the SHRP2 naturalistic driving study data to identify factors related to the selection of freeway ramp design speed.

DOT National Transportation Integrated Search

2017-03-01

This research explored the second Strategic Highway Research Program (SHRP2) Naturalistic Driving Study (NDS) database for the potential to identify freeway entrance and exit ramps and teen drivers behavior while traveling those ramps. This is in ...

Development of drive mechanism for an oscillating airfoil

NASA Technical Reports Server (NTRS)

Sticht, Clifford D.

1988-01-01

The design and development of an in-draft wind tunnel test section which will be used to study the dynamic stall of airfoils oscillating in pitch is described. The hardware developed comprises a spanned airfoil between schleiren windows, a four bar linkage, flywheels, a drive system and a test section structure.

Electric-Drive Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Septon, Kendall K

Electric-drive vehicles use electricity as their primary fuel or to improve the efficiency of conventional vehicle designs. These vehicles can be divided into three categories: Hybrid electric vehicles (HEVs), Plug-in hybrid electric vehicles (PHEVs), All-electric vehicles (EVs). Together, PHEVs and EVs can also be referred to as plug-in electric vehicles (PEVs).

Project Drive Teacher's Guide.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive Teacher's Manual complements eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklets is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training program. The guide begins…

40 CFR 86.1229-85 - Dynamometer load determination and fuel temperature profile.

Code of Federal Regulations, 2012 CFR

2012-07-01

... specified driving schedule. The design of the laboratory facility should include consideration of any parameters that may affect fuel temperatures, such as solar loading, pavement heat, and relative wind... be at least 125 °F throughout the driving period. Pavement temperature shall be measured and recorded...

40 CFR 86.1229-85 - Dynamometer load determination and fuel temperature profile.

Code of Federal Regulations, 2010 CFR

2010-07-01

... specified driving schedule. The design of the laboratory facility should include consideration of any parameters that may affect fuel temperatures, such as solar loading, pavement heat, and relative wind... be at least 125 °F throughout the driving period. Pavement temperature shall be measured and recorded...

40 CFR 86.1229-85 - Dynamometer load determination and fuel temperature profile.

Code of Federal Regulations, 2013 CFR

2013-07-01

... specified driving schedule. The design of the laboratory facility should include consideration of any parameters that may affect fuel temperatures, such as solar loading, pavement heat, and relative wind... be at least 125 °F throughout the driving period. Pavement temperature shall be measured and recorded...

40 CFR 86.1229-85 - Dynamometer load determination and fuel temperature profile.

Code of Federal Regulations, 2011 CFR

2011-07-01

... specified driving schedule. The design of the laboratory facility should include consideration of any parameters that may affect fuel temperatures, such as solar loading, pavement heat, and relative wind... be at least 125 °F throughout the driving period. Pavement temperature shall be measured and recorded...

Enhancing Science Kits with the Driving Question Board

ERIC Educational Resources Information Center

Nordine, Jeff; Torres, Ruben

2013-01-01

This article describes the driving question board (DQB), a visual organizer that supports inquiry-based instruction through the use of guiding questions. The DQB is a teaching aid designed to increase student engagement alongside science kits. Information is provided on its application to a lesson on buoyancy, highlighting how it improved…

Bus transit operational efficiency resulting from passenger boardings at park-and-ride facilities.

DOT National Transportation Integrated Search

2016-08-01

In order to save time and money by not driving to an ultimate destination, some urban commuters drive themselves a few miles to specially designated parking lots built for transit customers and located where trains or buses stop. The focus of this pa...

A summary report of six demonstration projects to reduce alcohol-impaired driving among 21- to 34-year-old drivers

DOT National Transportation Integrated Search

2008-04-01

This report summarizes six projects designed to address impaired driving among 21- to 34-year-olds. The report is organized into five chapters. The first chapter discusses the background and initiation of the projects. The second chapter provides a s...

A hybrid-drive nonisobaric-ignition scheme for inertial confinement fusion

DOE Office of Scientific and Technical Information (OSTI.GOV)

He, X. T., E-mail: xthe@iapcm.ac.cn; Center for Applied Physics and Technology, HEDPS, Peking University, Beijing 100871; IFSA Collaborative Innovation Center of MoE, Shanghai Jiao-Tong University, Shanghai 200240

A new hybrid-drive (HD) nonisobaric ignition scheme of inertial confinement fusion (ICF) is proposed, in which a HD pressure to drive implosion dynamics increases via increasing density rather than temperature in the conventional indirect drive (ID) and direct drive (DD) approaches. In this HD (combination of ID and DD) scheme, an assembled target of a spherical hohlraum and a layered deuterium-tritium capsule inside is used. The ID lasers first drive the shock to perform a spherical symmetry implosion and produce a large-scale corona plasma. Then, the DD lasers, whose critical surface in ID corona plasma is far from the radiationmore » ablation front, drive a supersonic electron thermal wave, which slows down to a high-pressure electron compression wave, like a snowplow, piling up the corona plasma into high density and forming a HD pressurized plateau with a large width. The HD pressure is several times the conventional ID and DD ablation pressure and launches an enhanced precursor shock and a continuous compression wave, which give rise to the HD capsule implosion dynamics in a large implosion velocity. The hydrodynamic instabilities at imploding capsule interfaces are suppressed, and the continuous HD compression wave provides main pdV work large enough to hotspot, resulting in the HD nonisobaric ignition. The ignition condition and target design based on this scheme are given theoretically and by numerical simulations. It shows that the novel scheme can significantly suppress implosion asymmetry and hydrodynamic instabilities of current isobaric hotspot ignition design, and a high-gain ICF is promising.« less

The Scaling of Bird Impact Loads

DTIC Science & Technology

1979-06-01

large air storage tank used for driving the gun. The driving air storage tank had a capacity of approximately 0.85 M 3 . There was a valve system...located between the driving air storage tank and the breech of tile gun. This valve system was designed to valve the high pressure air from the driving...821710.0000 %111 _x4 I4 (11Xt*11141 .14.0000 YIVNI~II 1 *uIi0000 MIAtV iIIflY*iA) 󈧕 .000 XS𔃾 ’,41(IINV*t141 ’I t1. 0000 YIl’m 214 ’tI#4’ tf1 : K.- ’’I.00001

Torque sensor

NASA Astrophysics Data System (ADS)

Fgeppert, E.

1984-09-01

Mechanical means for sensing turning torque generated by the load forces in a rotary drive system is described. The sensing means is designed to operate with minimal effect on normal operation of the drive system. The invention can be employed in various drive systems, e.g., automotive engine-transmission power plants, electric motor-operated tools, and metal cutting machines. In such drive systems, the torque-sensing feature may be useful for actuation of various control devices, such as electric switches, mechanical clutches, brake actuators, fluid control valves, or audible alarms. The torque-sensing function can be used for safety overload relief, motor de-energization, engine fuel control transmission clutch actuation, remote alarm signal, tool breakage signal, etc.

A Compilation of Data Relative to the Future Design of the Combat Vehicle Crewman’s Helmet DH-132

DTIC Science & Technology

1993-12-01

ISOUND LEVEL METER: I 9 K• IOTS I3&K 7006 13&K 21-i! M!CROPHOJE: I STATIONARY OPERATIOn -HIGHWAY DRIVING DRIVE-BY I __L_ N_ 4 151 1. ___(x...INTERIOR EXTERIOR IMICROPHONE LOCATION: I 1 {XI [ IDRIVERS POSITION i I *1 SI OCTAVE BAND CENTER FREqUENCIES (HZ)*1 I S I I SPEEDI I I I.ALL I I I I I I...HIGHWAY DRIVING DRIVE-BY I I B&K 4155 I ( ) IX) I I I INTERIOR EXTERIOR IMICROPHONE LOCATION: ( X) I I IDRIVER OCTAVE BAND CENTER FREqUEwCIES (HZ)I I I

Design and control of one precise tracking simulation bed for Chinese 20/30 meter optic/infrared telescope

NASA Astrophysics Data System (ADS)

Ren, Changzhi; Li, Xiaoyan; Song, Xiaoli; Niu, Yong; Li, Aihua; Zhang, Zhenchao

2012-09-01

Direct drive technology is the key to solute future 30-m and larger telescope motion system to guarantee a very high tracking accuracy, in spite of unbalanced and sudden loads such as wind gusts and in spite of a structure that, because of its size, can not be infinitely stiff. However, this requires the design and realization of unusually large torque motor that the torque slew rate must be extremely steep too. A conventional torque motor design appears inadequate. This paper explores one redundant unit permanent magnet synchronous motor and its simulation bed for 30-m class telescope. Because its drive system is one high integrated electromechanical system, one complexly electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. This paper discusses the design and control of the precise tracking simulation bed in detail.

Issues and Design Drivers for Deep Space Habitats

NASA Technical Reports Server (NTRS)

Anderson, Molly S.; Rucker, Michelle A.

2011-01-01

A cross-disciplinary team of scientists and engineers applied expertise gained in Lunar Lander development to the conceptual design of a long-duration, deep space habitat for Near Earth Asteroid (NEA) missions. The design reference mission involved two launches to assemble a 5-module vehicle for a 380-day round trip mission carrying 4 crew members. The conceptual design process yielded a number of interesting debates, some of which could be significant design drivers in a detailed Deep Space Habitat (DSH) design. These issues include: a) Launch loads: Potentially drives layout of equipment mounted to module floors or walls, and whether temporary internal structure is required to distribute launch loads to minimize shell mass; b) Unmanned loiter time: When added to an already lengthy mission, loiter time further drives risk and reliability, and poses issues for equipment shelf life such as material degradation or cryogenic fluids boil-off; c) Pointing and Visibility: A habitat embedded in a 5-module stack may drive Communications, Tracking, Guidance, and Navigation equipment out onto long booms to maintain line-of-sight visibility with targets. However, long booms will be more susceptible to disruption from exercise-induced vibration, potential damage during docking/undocking operations, and increased power distribution mass; d) Water: although it is assumed that a water processor will collect and recycle water, several interesting question were posed, such as: How much water to start with? Should potable water serve double-duty as radiation protection? And if so, should it be stowed in a single large tank, or smaller, portable containers? e) Design for repairability: one of the worst-case scenarios identified was a cabin depressurization that required suited repair from inside the module, potentially driving the need for long umbilical hoses or special equipment to allow smaller, mated modules to be used as safe havens for up to 180 days;

Predicting Alcohol-Impaired Driving among Spanish Youth with the Theory of Reasoned Action.

PubMed

Espada, José P; Griffin, Kenneth W; Gonzálvez, María T; Orgilés, Mireia

2015-06-19

Alcohol consumption is a risk factor for motor vehicle accidents in young drivers. Crashes associated with alcohol consumption typically have greater severity. This study examines the prevalence of driving under the influence among Spanish youth and tests the theory of reasoned action as a model for predicting driving under the influence. Participants included 478 Spanish university students aged 17-26 years. Findings indicated that alcohol was the substance most associated with impaired driving, and was involved in more traffic crashes. Men engage in higher levels of alcohol and other drug use, and perceived less risk in drunk driving (p < .01). The study confirms that alcohol use and driving under the influence of alcohol are highly prevalent in Spanish young people, and some gender differences exist in these behaviors (p < .01). Furthermore, the study confirms the validity of theory of reasoned action as a predictive model of driving under the influence of alcohol among youth in Spain (p < .001) and can help in the design of prevention programs.

78 FR 51737 - Notice of Issuance of Final Determination Concerning Certain Hard Disk Drives and Self-Encrypting...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... the HDA incorporate semiconductor, magnetic, mechanical, and manufacturing process design into an..., mechanical surface design and manufacturing process design. It takes approximately [xxx] hours to design... brand names ``Barracuda'' and ``Desktop''. HDDs are designed in the United States and assembled either...

Results-Based Interaction Design

ERIC Educational Resources Information Center

Weiss, Meredith

2008-01-01

Interaction design is a user-centered approach to development in which users and their goals are the driving force behind a project's design. Interaction design principles are fundamental to the design and implementation of effective websites, but they are not sufficient. This article argues that, to reach its full potential, a website should also…

Is It Time to Take Learning Design to Task?

ERIC Educational Resources Information Center

Griffiths, David; Inman, Maggie

2017-01-01

Context drives learning design, but too often context is not considered within learning design literature. Reported skill gaps lead to considerations around learning design and the security, completeness and depth of learning developed by learning designers in adult learning. Frequently learning is linked to context, where learning environments…

Viability of using different types of main oil pipelines pump drives

NASA Astrophysics Data System (ADS)

Zakirzakov, A. G.; Zemenkov, Yu D.; Akulov, K. A.

2018-05-01

The choice of the pumping units' drive of main oil pipelines is of great importance both for design of pipelines and for modernization of existing ones. At the beginning of oil pipeline transport development, due to the limited number and types of energy sources, the choice was not difficult. The combustion energy of the pumped product was often the only available energy resource for its transportation. In this regard, the pipelines that had autonomous energy sources favorably differed from other energy consumers in the sector. With the passage of time, with the development of the country's electricity supply system, the electric drive for power-line equipment of oil pipelines becomes the dominant type of a pumping station drive. Nowadays, the traditional component is an essential factor when choosing some type of the drive. For many years, oil companies have been using electric drives for pumps, while gas transport enterprises prefer self-contained gas turbines.

Does Simulator Sickness Impair Learning Decision Making While Driving a Police Vehicle? (Le mal du simulateur: un frein à l'apprentissage de la prise de décision en conduite d'un véhicule de police?)

ERIC Educational Resources Information Center

Paquette, Eve; Bélanger, Danielle-Claude

2015-01-01

The use of driving simulators is an innovation for police training in Quebec. There are some issues related to their impact on training objectives. This article presents the results of a study involving 71 police cadets who participated in six training sessions with a driving simulator. The training sessions were designed for developing the…

Striker Suitability Challenges in a Complex Threat Environment

DTIC Science & Technology

2008-04-23

áåÑçêãÉÇ=ÅÜ~åÖÉ=======- 163 - = = large number of wheel spindles developed fatigue cracks and had to be replaced early. Drive shafts are also failing... spindles developing fatigue cracks – drive shafts breaking – prescribed tire pressure is 80 PSI, however, with slat armor/sandbags – must maintain...drive shafts , differentials – Impairs off-road ops, larger footprint • Though not designed primarily for the urban fight (MOUT), Stryker is well-suited

Mechanical drive for blood pump

DOEpatents

Bifano, N.J.; Pouchot, W.D.

1975-07-29

This patent relates to a highly efficient blood pump to be used as a replacement for a ventricle of the human heart to restore people disabled by heart disease. The mechanical drive of the present invention is designed to operate in conjunction with a thermoelectric converter power source. The mechanical drive system essentially converts the output of a rotary power into pulsatile motion so that the power demand from the thermoelectric converter remains essentially constant while the blood pump output is pulsed. (auth)

Development of the solar array deployment and drive system for the XTE spacecraft

NASA Technical Reports Server (NTRS)

Farley, Rodger; Ngo, Son

1995-01-01

The X-ray Timing Explorer (XTE) spacecraft is a NASA science low-earth orbit explorer-class satellite to be launched in 1995, and is an in-house Goddard Space Flight Center (GSFC) project. It has two deployable aluminum honeycomb solar array wings with each wing being articulated by a single axis solar array drive assembly. This paper will address the design, the qualification testing, and the development problems as they surfaced of the Solar Array Deployment and Drive System.

An observational study of consumer use of fast-food restaurant drive-through lanes: implications for menu labelling policy.

PubMed

Roberto, Christina A; Hoffnagle, Elena; Bragg, Marie A; Brownell, Kelly D

2010-11-01

Some versions of restaurant menu labelling legislation do not require energy information to be posted on menus for drive-through lanes. The present study was designed to quantify the number of customers who purchase fast food through drive-in windows as a means of informing legislative labelling efforts. This was an observational study. The study took place at two McDonald's and Burger King restaurants, and single Dairy Queen, Kentucky Fried Chicken, Taco Bell and Wendy's restaurants. The number of customers entering the chain restaurants and purchasing food via the drive-through lane were recorded. A total of 3549 patrons were observed. The percentage of customers who made their purchases at drive-throughs was fifty-seven. The overall average (57 %) is likely a conservative estimate because some fast-food restaurants have late-night hours when only the drive-throughs are open. Since nearly six in ten customers purchase food via the drive-through lanes, menu labelling legislation should mandate the inclusion of menu labels on drive-through menu boards to maximise the impact of this public health intervention.

Design Alternatives to Improve Access Time Performance of Disk Drives Under DOS and UNIX

NASA Astrophysics Data System (ADS)

Hospodor, Andy

For the past 25 years, improvements in CPU performance have overshadowed improvements in the access time performance of disk drives. CPU performance has been slanted towards greater instruction execution rates, measured in millions of instructions per second (MIPS). However, the slant for performance of disk storage has been towards capacity and corresponding increased storage densities. The IBM PC, introduced in 1982, processed only a fraction of a MIP. Follow-on CPUs, such as the 80486 and 80586, sported 5-10 MIPS by 1992. Single user PCs and workstations, with one CPU and one disk drive, became the dominant application, as implied by their production volumes. However, disk drives did not enjoy a corresponding improvement in access time performance, although the potential still exists. The time to access a disk drive improves (decreases) in two ways: by altering the mechanical properties of the drive or by adding cache to the drive. This paper explores the improvement to access time performance of disk drives using cache, prefetch, faster rotation rates, and faster seek acceleration.

Steering the conversation: A linguistic exploration of natural language interactions with a digital assistant during simulated driving.

PubMed

Large, David R; Clark, Leigh; Quandt, Annie; Burnett, Gary; Skrypchuk, Lee

2017-09-01

Given the proliferation of 'intelligent' and 'socially-aware' digital assistants embodying everyday mobile technology - and the undeniable logic that utilising voice-activated controls and interfaces in cars reduces the visual and manual distraction of interacting with in-vehicle devices - it appears inevitable that next generation vehicles will be embodied by digital assistants and utilise spoken language as a method of interaction. From a design perspective, defining the language and interaction style that a digital driving assistant should adopt is contingent on the role that they play within the social fabric and context in which they are situated. We therefore conducted a qualitative, Wizard-of-Oz study to explore how drivers might interact linguistically with a natural language digital driving assistant. Twenty-five participants drove for 10 min in a medium-fidelity driving simulator while interacting with a state-of-the-art, high-functioning, conversational digital driving assistant. All exchanges were transcribed and analysed using recognised linguistic techniques, such as discourse and conversation analysis, normally reserved for interpersonal investigation. Language usage patterns demonstrate that interactions with the digital assistant were fundamentally social in nature, with participants affording the assistant equal social status and high-level cognitive processing capability. For example, participants were polite, actively controlled turn-taking during the conversation, and used back-channelling, fillers and hesitation, as they might in human communication. Furthermore, participants expected the digital assistant to understand and process complex requests mitigated with hedging words and expressions, and peppered with vague language and deictic references requiring shared contextual information and mutual understanding. Findings are presented in six themes which emerged during the analysis - formulating responses; turn-taking; back-channelling, fillers and hesitation; vague language; mitigating requests and politeness and praise. The results can be used to inform the design of future in-vehicle natural language systems, in particular to help manage the tension between designing for an engaging dialogue (important for technology acceptance) and designing for an effective dialogue (important to minimise distraction in a driving context). Copyright © 2017 Elsevier Ltd. All rights reserved.

Design and Analysis of Drive Shaft using Kevlar/Epoxy and Glass/Epoxy as a Composite Material

NASA Astrophysics Data System (ADS)

Karthikeyan, P.; Gobinath, R.; Kumar, L. Ajith; Jenish, D. Xavier

2017-05-01

In automobile industry drive shaft is one of the most important components to transmit power form the engine to rear wheel through the differential gear. Generally steel drive shaft is used in automobile industry, nowadays they are more interested to replace steel drive shaft with that of composite drive shaft. The overall objective of this paper is to analyze the composite drive shaft using to find out the best replacement for conventional steel drive shaft. The uses of advanced composite materials such as Kevlar, Graphite, Carbon and Glass with proper resins ware resulted in remarkable achievements in automobile industry because of its greater specific strength and specific modulus, improved fatigue and corrosion resistances and reduction in energy requirements due to reduction in weight as compared to steel shaft. This paper is to presents, the modeling and analysis of drive shaft using Kevlar/Epoxy and Glass/Epoxy as a composite material and to find best replacement for conventional steel drive shafts with an Kevlar/epoxy or Glass/Epoxy resin composite drive shaft. Modeling is done using CATIA software and Analysis is carried out by using ANSYS 10.0 software for easy understanding. The composite drive shaft reduces the weight by 81.67 % for Kevlar/Epoxy and 72.66% for Glass/Epoxy when compared with conventional steel drive shaft.

Using alcohol intoxication goggles (Fatal Vision® goggles) to detect alcohol related impairment in simulated driving.

PubMed

McCartney, Danielle; Desbrow, Ben; Irwin, Christopher

2017-01-02

Fatal vision goggles (FVGs) are image-distorting equipment used within driver education programs to simulate alcohol-related impairment. However, there is no empirical evidence comparing the behavioral effects associated with wearing FVGs to alcohol intoxication. The purpose of this study was to determine the validity of FVGs in producing alcohol-related impairment in simulated driving. Twenty-two healthy males (age: 23 ± 3 years, mean ± SD) participated in a placebo-controlled crossover design study involving 4 experimental trials. In each trial, participants completed a baseline level simulated driving task followed by an experimental driving task, involving one of 4 treatments: (1) a dose of alcohol designed to elicit 0.080% breath alcohol concentration (BrAC; AB), (2) an alcohol placebo beverage (PB), (3) FVG (estimated % blood alcohol concentration [BAC] 0.070-0.100+), and (4) placebo goggles (PGs). The driving tasks included 3 separate scenarios lasting ∼5 min each; these were a simple driving scenario, a complex driving scenario, and a hazard perception driving scenario. Selected lateral control parameters (standard deviation of lane position [SDLP]; total number of lane crossings [LCs]) and longitudinal control parameters (average speed; standard deviation of speed [SDSP]; distance headway; minimum distance headway) were monitored during the simple and complex driving scenarios. Latency to 2 different stimuli (choice reaction time [CRT]) was tested in the hazard perception driving scenario. Subjective ratings of mood and attitudes toward driving were also provided during each of the trials. Neither placebo treatment influenced simulated driving performance. Mean BrAC was 0.060 ± 0.010% at the time of driving on the AB trial. Lateral control: In the simple driving scenario, SDLP and LC were not affected under any of the experimental treatments. However, in the complex driving scenario, significantly greater SDLP was observed on both the FVG and AB trials compared to their respective baseline drives. LC increased significantly from baseline on the AB trial only. Longitudinal control: Speed was not affected by any of the experimental treatments; however, SDSP increased significantly from baseline on the FVG trial. A significant reduction in distance headway and minimum distance headway was detected on the FVG trial compared to baseline. Hazard perception: Neither AB nor FVG trials were influential on CRT. Subjective mood ratings were significantly altered on the AB and FVG trials compared to baseline and placebo conditions. Participants reported reduced willingness and ability to drive under the active treatments (AB and FVG) than the placebo treatments (PB and PG). FVGs may have some utility in replicating alcohol-related impairment on specific driving performance measurements. Hence, the equipment may offer an alternative approach to researching the impact of alcohol intoxication on simulated driving performance among populations where the provision of alcohol would otherwise be unethical (e.g., prelicensed drivers).

Design and reliability of a MEMS thermal rotary actuator.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Michael Sean; Corwin, Alex David

2007-09-01

A new rotary MEMS actuator has been developed and tested at Sandia National Laboratories that utilizes a linear thermal actuator as the drive mechanism. This actuator was designed to be a low-voltage, high-force alternative to the existing electrostatic torsional ratcheting actuator (TRA) [1]. The new actuator, called the Thermal Rotary Actuator (ThRA), is conceptually much simpler than the TRA and consists of a gear on a hub that is turned by a linear thermal actuator [2] positioned outside of the gear. As seen in Figure 1, the gear is turned through a ratcheting pawl, with anti-reverse pawls positioned around themore » gear for unidirectional motion (see Figure 1). A primary consideration in the design of the ThRA was the device reliability and in particular, the required one-to-one relationship between the ratcheting output motion and the electrical input signal. The electrostatic TRA design has been shown to both over-drive and under-drive relative to the number of input pulses [3]. Two different ThRA designs were cycle tested to measure the skip rate. This was done in an automated test setup by using pattern matching to measure the angle of rotation of the output gear after a defined number of actuation pulses. By measuring this gear angle over time, the number of skips can be determined. Figure 2 shows a picture of the ThRA during testing, with the pattern-matching features highlighted. In the first design tested, it was found that creep in the thermal actuator limited the number of skip-free cycles, as the rest position of the actuator would creep forward enough to prevent the counter-rotation pawls from fully engaging (Figure 3). Even with this limitation, devices were measured with up to 100 million cycles with no skipping. A design modification was made to reduce the operating temperature of the thermal actuator which has been shown in a previous study [2] to reduce the creep rate. In addition, changes were made to the drive ratchet design and actuation direction to increase the available output force. This new design was tested and shown to operate in one case out to greater than 360 million cycles without any skipping, after which the test was stopped without failure. The output force was also measured as a function of input voltage (Figure 4), and shown to be higher than the previous design. The maximum force shown in the figure is a limit of the gauge used, not the actuator itself. Continued work for this design will focus on understanding the actuator performance while driving a load, as all current tests were performed with no load on the output gear.« less

Requirements and Capabilities for Fielding Cryogenic DT-Containing Fill-Tube Targets for Direct-Drive Experiments on OMEGA

DOE PAGES

Harding, D. R.; Ulreich, J.; Wittman, M. D.; ...

2017-12-06

Improving the performance of direct-drive cryogenic targets at the Omega Laser Facility requires the development of a new cryogenic system to (i) field non permeable targets with a fill tube, and (ii) provide a clean environment around the target. This capability is to demonstrate that imploding a scaled-down version of the direct-drive–ignition target for the National Ignition Facility (NIF) on the OMEGA laser will generate the hot-spot pressure that is needed for ignition; this will justify future cryogenic direct-drive experiments on the NIF. The paper describes the target, the cryogenic equipment that is being constructed to achieve this goal, andmore » the proposed target delivery process. Thermal calculations, fill-tube–based target designs, and structural/vibrational analyses are provided to demonstrate the credibility of the design. This new design will include capabilities not available (or possible) with the existing OMEGA cryogenic system, with the emphasis being to preserve a pristinely clean environment around the target, and to provide upgraded diagnostics to characterize both the ice layer and the target’s surface. The conceptual design is complete and testing of prototypes and subcomponents is underway. The rationale and capabilities of the new design are discussed.« less

Requirements and Capabilities for Fielding Cryogenic DT-Containing Fill-Tube Targets for Direct-Drive Experiments on OMEGA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harding, D. R.; Ulreich, J.; Wittman, M. D.

Improving the performance of direct-drive cryogenic targets at the Omega Laser Facility requires the development of a new cryogenic system to (i) field non permeable targets with a fill tube, and (ii) provide a clean environment around the target. This capability is to demonstrate that imploding a scaled-down version of the direct-drive–ignition target for the National Ignition Facility (NIF) on the OMEGA laser will generate the hot-spot pressure that is needed for ignition; this will justify future cryogenic direct-drive experiments on the NIF. The paper describes the target, the cryogenic equipment that is being constructed to achieve this goal, andmore » the proposed target delivery process. Thermal calculations, fill-tube–based target designs, and structural/vibrational analyses are provided to demonstrate the credibility of the design. This new design will include capabilities not available (or possible) with the existing OMEGA cryogenic system, with the emphasis being to preserve a pristinely clean environment around the target, and to provide upgraded diagnostics to characterize both the ice layer and the target’s surface. The conceptual design is complete and testing of prototypes and subcomponents is underway. The rationale and capabilities of the new design are discussed.« less

An Arduino-Based Resonant Cradle Design with Infant Cries Recognition

PubMed Central

Chao, Chun-Tang; Wang, Chia-Wei; Chiou, Juing-Shian; Wang, Chi-Jo

2015-01-01

This paper proposes a resonant electric cradle design with infant cries recognition, employing an Arduino UNO as the core processor. For most commercially available electric cradles, the drive motor is closely combined with the bearing on the top, resulting in a lot of energy consumption. In this proposal, a ball bearing design was adopted and the driving force is under the cradle to increase the distance from the object to fulcrum and torque. The sensors are designed to detect the oscillation state, and then the force is driven at the critical time to achieve the maximum output response while saving energy according to the principle of resonance. As for the driving forces, the winding power and motors are carefully placed under the cradle. The sensors, including the three-axis accelerometer and infrared sensor, are tested and applied under swinging amplitude control. In addition, infant cry recognition technology was incorporated in the design to further develop its functionality, which is a rare feature in this kind of hardware. The proposed nonlinear operator of fundamental frequency (f0) analysis is able to identify different types of infant cries. In conclusion, this paper proposes an energy-saving electric cradle with infant cries recognition and the experimental results demonstrate the effectiveness of this approach. PMID:26247947

An Arduino-Based Resonant Cradle Design with Infant Cries Recognition.

PubMed

Chao, Chun-Tang; Wang, Chia-Wei; Chiou, Juing-Shian; Wang, Chi-Jo

2015-08-03

This paper proposes a resonant electric cradle design with infant cries recognition, employing an Arduino UNO as the core processor. For most commercially available electric cradles, the drive motor is closely combined with the bearing on the top, resulting in a lot of energy consumption. In this proposal, a ball bearing design was adopted and the driving force is under the cradle to increase the distance from the object to fulcrum and torque. The sensors are designed to detect the oscillation state, and then the force is driven at the critical time to achieve the maximum output response while saving energy according to the principle of resonance. As for the driving forces, the winding power and motors are carefully placed under the cradle. The sensors, including the three-axis accelerometer and infrared sensor, are tested and applied under swinging amplitude control. In addition, infant cry recognition technology was incorporated in the design to further develop its functionality, which is a rare feature in this kind of hardware. The proposed nonlinear operator of fundamental frequency (f0) analysis is able to identify different types of infant cries. In conclusion, this paper proposes an energy-saving electric cradle with infant cries recognition and the experimental results demonstrate the effectiveness of this approach.

Thermally Simulated 32kW Direct-Drive Gas-Cooled Reactor: Design, Assembly, and Test

NASA Astrophysics Data System (ADS)

Godfroy, Thomas J.; Kapernick, Richard J.; Bragg-Sitton, Shannon M.

2004-02-01

One of the power systems under consideration for nuclear electric propulsion is a direct-drive gas-cooled reactor coupled to a Brayton cycle. In this system, power is transferred from the reactor to the Brayton system via a circulated closed loop gas. To allow early utilization, system designs must be relatively simple, easy to fabricate, and easy to test using non-nuclear heaters to closely mimic heat from fission. This combination of attributes will allow pre-prototypic systems to be designed, fabricated, and tested quickly and affordably. The ability to build and test units is key to the success of a nuclear program, especially if an early flight is desired. The ability to perform very realistic non-nuclear testing increases the success probability of the system. In addition, the technologies required by a concept will substantially impact the cost, time, and resources required to develop a successful space reactor power system. This paper describes design features, assembly, and test matrix for the testing of a thermally simulated 32kW direct-drive gas-cooled reactor in the Early Flight Fission - Test Facility (EFF-TF) at Marshall Space Flight Center. The reactor design and test matrix are provided by Los Alamos National Laboratories.

Epos TCS Satellite Data

NASA Astrophysics Data System (ADS)

Manunta, Michele; Mandea, Mioara; Fernández-Turiel, José Luis; Stramondo, Salvatore; Wright, Tim; Walter, Thomas; Bally, Philippe; Casu, Francesco; Zeni, Giovanni; Buonanno, Sabatino; Zinno, Ivana; Tizzani, Pietro; Castaldo, Raffaele; Ostanciaux, Emilie; Diament, Michel; Hooper, Andy; Maccaferri, Francesco; Lanari, Riccardo

2016-04-01

TCS Satellite Data is devoted to provide Earth Observation (EO) services, transversal with respect to the large EPOS community, suitable to be used in several application scenarios. In particular, the main goal is to contribute with mature services that have already well demonstrated their effectiveness and relevance in investigating the physical processes controlling earthquakes, volcanic eruptions and unrest episodes as well as those driving tectonics and Earth surface dynamics. The TCS Satellite Data will provide two kinds of services: satellite products/services, and Value-added satellite products/services. The satellite products/services are composed of three (EPOSAR, GDM and COMET) well-identified and partly already operational elements for delivering Level 1 products. Such services will be devoted to the generation of SAR interferograms, DTM and ground displacement maps through the exploitation of different advanced EO techniques for InSAR and optical data analysis. The Value-added satellite products/services are composed of 4 elements (EPOSAR, 3D-Def, Mod and COMET) of Level 2 and 3 products. Such services integrate satellite and in situ measurements and observations to retrieve information on source mechanism, such as the geometry (spatial location, depth, volume changes) and the physical parameters of the deformation sources, through the exploitation of modelling approaches. The TCS Satellite Data will provide products in two different processing and delivery modes: 1- surveillance mode - routinely product generation; 2- on demand mode - product generation performed on demand by the user. Concerning the surveillance mode, the goal is providing continuous satellite measurements in areas of particular interest from a geophysical perspective (supersites). The objective is the detection of displacement patterns changing along time and their geophysical explanation. This is a valid approach for inter-seismic movements and volcanic unrest, post-seismic and post-eruptive displacements, urban subsidence, coastal movements. The on demand mode will allow users to process available satellite data-stack by selecting the scenes and the area of interest, and properly setting some processing parameters or to perform modelling analyses. This processing mode will guarantee the possibility to analyse areas of interest for the users, thus exploiting as much as possible the global coverage strategy of satellites, as well as performing user-driven processing, benefiting from the knowledge of the characteristics of the particular investigated area and/or deformation phenomenon.

Microstructure Applications for Battery Design | Transportation Research |

Science.gov Websites

NREL Microstructure Applications for Battery Design Microstructure Applications for Battery Design NREL's Computer-Aided Engineering for Electric Drive Vehicle Batteries (CAEBAT) work includes simulating physics at the electrode microstructure level and created a virtual design tool for battery

Las Cumbres Observatory 1-Meter Global Science Telescope Network

NASA Astrophysics Data System (ADS)

Pickles, Andrew; Dubberley, M.; Haldeman, B.; Haynes, R.; Posner, V.; Rosing, W.; staff, LCOGT

2009-05-01

We present the optical, mechanical and electronic design of the LCOGT 1-m telescope. These telescopes are planned to go in pairs to each of 6 sites worldwide, complementing 0.4m telescopes and 2-m telescopes at two existing sites. This science network is designed to provide continuously available photometric monitoring and spectroscopy of variable sources. The 1-m optical design is an f/8 quasi-RC system, with a doublet corrector and field flattener to provide good image quality out to 0.8 degrees. The field of view of the Fairchild 4K science CCD is 27 arcmin, with 0.39 arcsec pixels. The mechanical design includes a stiff C-ring equatorial mount and friction drive rollers, mounted on a triangular base that can be adjusted for latitude. Another friction drive is coupled at the Declination axis to the M1 mirror cell, that forms the main Optical Tube Assembly (OTA) structural element. The OTA design includes a stiff carbon fiber truss assembly, with offset vanes to an M2 drive that provides remote focus, tilt and collimation. The tube assembly weighs about 600 Kg, including Hextek mirrors, 4K science CCD, filter wheel, autoguiders and medium resolution spectrograph pick-off fiber. The telescopes will be housed in domes at existing observatory sites. They are designed to operate remotely and reliably under centralized control for automatic, optimized scheduling of observations with available hardware.

The Impact of Distraction on the Driving Performance of Adolescents with and without Attention Deficit Hyperactivity Disorder

PubMed Central

Narad, Megan; Garner, Annie A.; Brassell, Anne A.; Saxby, Dyani; Antonini, Tanya N.; O'Brien, Kathleen M.; Tamm, Leanne; Matthews, Gerald; Epstein, Jeffery N.

2013-01-01

Importance This study extends the literature regarding Attention-Deficit/Hyperactivity Disorder (ADHD) related driving impairments to a newly-licensed, adolescent population. Objective To investigate the combined risks of adolescence, ADHD, and distracted driving (cell phone conversation and text messaging) on driving performance. Design Adolescents with and without ADHD engaged in a simulated drive under three conditions (no distraction, cell phone conversation, texting). During each condition, one unexpected event (e.g., car suddenly merging into driver's lane) was introduced. Setting Driving simulator. Participants Adolescents aged 16–17 with ADHD (n=28) and controls (n=33). Interventions/Main Exposures Cell phone conversation, texting, and no distraction while driving. Outcome Measures Self-report of driving history; Average speed, standard deviation of speed, standard deviation of lateral position, braking reaction time during driving simulation. Results Adolescents with ADHD reported fewer months of driving experience and a higher proportion of driving violations than controls. After controlling for months of driving history, adolescents with ADHD demonstrated more variability in speed and lane position than controls. There were no group differences for braking reaction time. Further, texting negatively impacted the driving performance of all participants as evidenced by increased variability in speed and lane position. Conclusions This study, one of the first to investigate distracted driving in adolescents with ADHD, adds to a growing body of literature documenting that individuals with ADHD are at increased risk for negative driving outcomes. Furthermore, texting significantly impairs the driving performance of all adolescents and increases existing driving-related impairment in adolescents with ADHD, highlighting the need for education and enforcement of regulations against texting for this age group. PMID:23939758

The influence of music on mental effort and driving performance.

PubMed

Ünal, Ayça Berfu; Steg, Linda; Epstude, Kai

2012-09-01

The current research examined the influence of loud music on driving performance, and whether mental effort mediated this effect. Participants (N=69) drove in a driving simulator either with or without listening to music. In order to test whether music would have similar effects on driving performance in different situations, we manipulated the simulated traffic environment such that the driving context consisted of both complex and monotonous driving situations. In addition, we systematically kept track of drivers' mental load by making the participants verbally report their mental effort at certain moments while driving. We found that listening to music increased mental effort while driving, irrespective of the driving situation being complex or monotonous, providing support to the general assumption that music can be a distracting auditory stimulus while driving. However, drivers who listened to music performed as well as the drivers who did not listen to music, indicating that music did not impair their driving performance. Importantly, the increases in mental effort while listening to music pointed out that drivers try to regulate their mental effort as a cognitive compensatory strategy to deal with task demands. Interestingly, we observed significant improvements in driving performance in two of the driving situations. It seems like mental effort might mediate the effect of music on driving performance in situations requiring sustained attention. Other process variables, such as arousal and boredom, should also be incorporated to study designs in order to reveal more on the nature of how music affects driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

Predicting drowsy driving in real-time situations: Using an advanced driving simulator, accelerated failure time model, and virtual location-based services.

PubMed

Wang, Junhua; Sun, Shuaiyi; Fang, Shouen; Fu, Ting; Stipancic, Joshua

2017-02-01

This paper aims to both identify the factors affecting driver drowsiness and to develop a real-time drowsy driving probability model based on virtual Location-Based Services (LBS) data obtained using a driving simulator. A driving simulation experiment was designed and conducted using 32 participant drivers. Collected data included the continuous driving time before detection of drowsiness and virtual LBS data related to temperature, time of day, lane width, average travel speed, driving time in heavy traffic, and driving time on different roadway types. Demographic information, such as nap habit, age, gender, and driving experience was also collected through questionnaires distributed to the participants. An Accelerated Failure Time (AFT) model was developed to estimate the driving time before detection of drowsiness. The results of the AFT model showed driving time before drowsiness was longer during the day than at night, and was longer at lower temperatures. Additionally, drivers who identified as having a nap habit were more vulnerable to drowsiness. Generally, higher average travel speeds were correlated to a higher risk of drowsy driving, as were longer periods of low-speed driving in traffic jam conditions. Considering different road types, drivers felt drowsy more quickly on freeways compared to other facilities. The proposed model provides a better understanding of how driver drowsiness is influenced by different environmental and demographic factors. The model can be used to provide real-time data for the LBS-based drowsy driving warning system, improving past methods based only on a fixed driving. Copyright © 2016 Elsevier Ltd. All rights reserved.

Designing low cost LED display for the billboard

NASA Astrophysics Data System (ADS)

Hong, Yi-Jian; Uang, Chii-Maw; Wang, Ping-Chieh; Ho, Zu-Sheng

2011-10-01

With quickly advance of the computer, microelectronics and photonics technologies, LED display panel becomes a new electronic advertising media. It can be used to show any information whatever characters or graphics. Most LED display panels are built of many Light-Emitting Diodes arranged in a matrix form. The display has many advantages such as low power, low cost, long life and high definition. Because the display panel is asked to show rich color, the LED display panel's driving system becomes very complex. The design methodology of LED display panel's driver becomes more and more important to meet the market requirements. Cost is always the most important issue in public market domain. In this paper, we report a design methodology of LED display panel's driver based on the microprocessor control unit (MCU) system and LED display controller IC, HT1632C, to control three colors, RGB, color LED display panel and the modular panel size is 24*16 in matrix form. The HT1632C is a memory mapping LED display controller, it can be used on many applications, such as digital clock, thermometer, counter, voltmeter or other instrumentation readouts. Three pieces of HT1632C are used to drive a 24*16 RGB LED display panel, in our design case. Each HT163C chip is used to control one of the R, G and B color. As the drive mode is driven in DC mode, the RGB display panel can create and totally of seven colors under the control of MCU. The MCU generates the control signal to drive HT1632C. In this study, the software design methodology is adopted with dynamic display principle. When the scan frequency is 60Hz, LED display panel will get the clear picture and be able to display seven colors.

Integrated chassis control for a three-axle electric bus with distributed driving motors and active rear steering system

NASA Astrophysics Data System (ADS)

Liu, Wei; He, Hongwen; Sun, Fengchun; Lv, Jiangyi

2017-05-01

This paper describes an integrated chassis control framework for a novel three-axle electric bus with active rear steering (ARS) axle and four motors at the middle and rear wheels. The proposed integrated framework consists of four parts: (1) an active speed limiting controller is designed for anti-body slip control and rollover prevention; (2) an ARS controller is designed for coordinating the tyre wear between the driving wheels; (3) an inter-axle torque distribution controller is designed for optimal torque distribution between the axles, considering anti-wheel slip and battery power limitations and (4) a data acquisition and estimation module for collecting the measured and estimated vehicle states. To verify the performances, a simulation platform is established in Trucksim software combined with Simulink. Three test cases are particularly designed to show the performances. The proposed algorithm is compared with a simple even control algorithm. The test results show satisfactory lateral stability and rollover prevention performances under severe steering conditions. The desired tyre wear coordinating performance is also realised, and the wheel slip ratios are restricted within stable region during intensive driving and emergency braking with complicated road conditions.

Effect of rear end spoiler angle of a sedan car

NASA Astrophysics Data System (ADS)

Mashud, Mohammad; Das, Rubel Chandra

2017-06-01

Automotive vehicle's performance, safety, maneuverability can be influenced by multi-disciplinary factors such as car engine, tires, aerodynamics, and ergonomics of design. With the recent years, inflation in the fuel prices & the demand to have reduced greenhouse emissions has played a significant role in redefining the car aerodynamics. The shape of the vehicle uses about 3% of fuel to overcome the resistance in urban driving, while it takes 11% of fuel for the highway driving. This considerable high value of fuel usage in highway driving attracts several design engineers to enhance the aerodynamics of the vehicle using minimal design changes. Besides, automotive vehicles have become so much faster experiencing uplift force which creates unexpected accidents. This brings the idea of using external devices, which could be attached to the present vehicle without changing the body. This paper is based on the design, developments and numeral calculation of the effects of external device, which will be spoiler that mounted at the rear side of the sedan car to make the present vehicles more aerodynamically attractive. The influence of rear spoiler on the generated lift, drag, and pressure distributions are investigated and reported using commercially available Autodesk Simulation CFD software tool.

Use of designated boat operators and designated drivers among college students.

PubMed

Cheong, JeeWon; Hall, Nicole M; MacKinnon, David P

2006-07-01

Prior research has shown that designated drivers (DD) are widely used as a preventive measure for driving under the influence. Despite the prevalence of alcohol involvement in boating accidents, much less is known about the use of a designated boat operator (DBO). The current study investigated the prevalence of DBO use in recreational boating and compared the characteristics of DD users and DBO users. Several survey questionnaires were distributed to a group of undergraduate students at a large southwestern university for the purpose of investigating demographic characteristics, alcohol-use pattern, and other alcohol-related problem behaviors, such as driving and boating under the influence. Approximately 45% of the boaters reported they had drunk alcohol while boating, and approximately 70% had used a DBO in the most recent boating event. The DBO users were found to be similar to the DD users in terms of drinking pattern, age of drinking onset, and driving behaviors. High rates of alcohol use in recreational boating suggest the need for prevention strategies. Furthermore, future studies are needed to investigate the selection process of the DBOs and the differences between passengers and boat operators, which could shed light on strategies to prevent alcohol- involved boating injuries.

Design, Generation and Tooth Contact Analysis (TCA) of Asymmetric Face Gear Drive With Modified Geometry

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Fuentes, Alfonso; Hawkins, J. M.; Handschuh, Robert F.

2001-01-01

A new type of face gear drive for application in transmissions, particularly in helicopters, has been developed. The new geometry differs from the existing geometry by application of asymmetric profiles and double-crowned pinion of the face gear mesh. The paper describes the computerized design, simulation of meshing and contact, and stress analysis by finite element method. Special purpose computer codes have been developed to conduct the analysis. The analysis of this new type of face gear is illustrated with a numerical example.

Double axis, two-crystal x-ray spectrometer.

PubMed

Erez, G; Kimhi, D; Livnat, A

1978-05-01

A two-crystal double axis x-ray spectrometer, capable of goniometric accuracy on the order of 0.1", has been developed. Some of its unique design features are presented. These include (1) a modified commercial thrust bearing which furnishes a precise, full circle theta:2theta coupling, (2) a new tangent drive system design in which a considerable reduction of the lead screw effective pitch is achieved, and (3) an automatic step scanning control which eliminates most of the mechanical deficiencies of the tangent drive by directly reading the tangent arm displacement.

High frequency magnetostrictive transducers for waveguide applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daw, Joshua Earl; Taylor, Steven Cheney; Rempe, Joy Lynn

A high frequency magnetostrictive transducer includes a magnetostrictive rod or wire inserted co-axially into a driving coil, wherein the driving coil includes a coil arrangement with a plurality of small coil segments along the magnetostrictive rod or wire; wherein frequency operation of the high frequency magnetostrictive transducer is controlled by a length of the small coil segments and a material type of the magnetostrictive rod or wire. This design of the high frequency magnetostrictive transducer retains the beneficial aspects of the magnetostrictive design, while reducing its primary drawback, lower frequency operation.

Design verification tests for an axial gap permanent magnet compressor motor

NASA Astrophysics Data System (ADS)

Hawsey, R. A.; Bailey, J. M.

1987-07-01

A 30-hp, direct-drive, permanent magnet motor (PMM) has been constructed. The motor is to operate at 15,000 rpm and is designed to drive a Worthington compressor at the US DOE-owned gaseous diffusion plants. The PMM prevents traditional dynamometer testing, including locked rotor current, voltage, and torque measurements. A test plan is presented for data acquisition on the dynamometer test stand in order to calculate the equivalent circuit for the motor. A description of the hardware required for these measurements is included in the plan.

“I wasn’t texting; I was just reading an email …”: a qualitative study of distracted driving enforcement in Washington State

PubMed Central

Nevin, Paul E; Blanar, Laura; Kirk, Annie Phare; Freedheim, Amy; Kaufman, Robert; Hitchcock, Laura; Maeser, Jennifer D; Ebel, Beth E

2018-01-01

Background In response to the rise of distracted driving, many countries and most US states have adopted laws to restrict the use of handheld phones for drivers. Specific provisions of each law and the overall social mores of distracted driving influence enforceability and impact. Objectives Identify multilevel interdependent factors that influence distracted driving enforcement through the perspective of police officers. Design/methods We conducted focus group discussions with active duty law enforcement officers from three large Washington State counties. Our thematic analysis used descriptive and pattern coding that placed our findings within a social ecological framework to facilitate targeted intervention development. Results Participants reported that the distracted driving law posed challenges for consistent and effective enforcement. They emphasised the need to change social norms around distracted driving, similar to the shifts seen around impaired driving. Many participants were themselves distracted drivers, and their individual knowledge, attitude and beliefs influenced enforcement. Participants suggested that law enforcement leaders and policymakers should develop and implement policies and strategies to prioritise and motivate increased distracted driving enforcement. Conclusions Individual, interpersonal, organisational and societal factors influence enforcement of distracted driving laws. Targeted interventions should be developed to address distracted driving and sustain effective enforcement. PMID:27634839

On the Dynamics of Rocking Motion of the Hard-Disk Drive Spindle Motor System

NASA Astrophysics Data System (ADS)

Wang, Joseph

Excessive rocking motion of the spindle motor system can cause track misregistration resulting in poor throughput or even drive failure. The chance of excessive disk stack rocking increases as a result of decreasing torsional stiffness of spindle motor bearing system due to the market demand for low profile hard drives. As the track density increases and the vibration specification becomes increasingly stringent, rocking motion of a spindle motor system deserves even more attention and has become a primary challenge for a spindle motor system designer. Lack of understanding of the rocking phenomenon combined with misleading paradox has presented a great difficulty in the effort of avoiding the rocking motion in the hard-disk drive industry. This paper aims to provide fundamental understanding of the rocking phenomenon of a rotating spindle motor system, to clarify the paradox in disk-drive industry and to provide a design guide to an optimized spindle system. This paper, theoretically and experimentally, covers a few important areas of industrial interest including the prediction of rocking natural frequencies and mode shape of a rotating spindle, free vibration, and frequency response under common forcing functions such as rotating and fixed-plane forcing functions. The theory presented here meets with agreeable experimental observation.

Differential-Drive Mobile Robot Control Design based-on Linear Feedback Control Law

NASA Astrophysics Data System (ADS)

Nurmaini, Siti; Dewi, Kemala; Tutuko, Bambang

2017-04-01

This paper deals with the problem of how to control differential driven mobile robot with simple control law. When mobile robot moves from one position to another to achieve a position destination, it always produce some errors. Therefore, a mobile robot requires a certain control law to drive the robot’s movement to the position destination with a smallest possible error. In this paper, in order to reduce position error, a linear feedback control is proposed with pole placement approach to regulate the polynoms desired. The presented work leads to an improved understanding of differential-drive mobile robot (DDMR)-based kinematics equation, which will assist to design of suitable controllers for DDMR movement. The result show by using the linier feedback control method with pole placement approach the position error is reduced and fast convergence is achieved.

Design and control of a high precision drive mechanism

NASA Astrophysics Data System (ADS)

Pan, Bo; He, Yongqiang; Wang, Haowei; Zhang, Shuyang; Zhang, Donghua; Wei, Xiaorong; Jiang, Zhihong

2017-01-01

This paper summarizes the development of a high precision drive mechanism (HPDM) for space application, such as the directional antenna, the laser communication device, the mobile camera and other pointing mechanisms. In view of the great practical significance of high precision drive system, control technology for permanent magnet synchronous motor (PMSM) servo system is also studied and a PMSM servo controller is designed in this paper. And the software alignment was applied to the controller to eliminate the steady error of the optical encoder, which helps to realize the 1 arcsec (1σ) control precision. To assess its capabilities, the qualification environment testing including the thermal vacuum cycling testing, and the sinusoidal and random vibration were carried out. The testing results show that the performance of the HPDM is almost the same between the former and the end of each testing.

A system for diagnosis, referral, and rehabilitation of persons convicted of driving while intoxicated : the system and a preliminary field test of the diagnostic procedure

DOT National Transportation Integrated Search

1978-04-01

A diagnostic, referral and treatment program was designed for persons convicted of driving while intoxicated. The assessment system measures the individual on an adaptability factor, a sociocultural factor and a severity factor. The assessment leads ...

75 FR 77938 - Notice of Intent To Release Certain Properties From Federal Obligations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... the property for other than aeronautical purposes. The property is located adjacent to Crystal Lake Drive in Orange County, Florida. The parcel is currently designated as non-aeronautical use. The....71 acre parcels to be acquired is also located adjacent to Crystal Lake Drive in Orange County...

Maintenance. Book Three. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Maintenance is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training program. The booklet…

Insurance. Book Eight. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Insurance is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training program. The booklet…

Parent-Teen Training Aide = Guia de Instruccion para Padres y Jovenes.

ERIC Educational Resources Information Center

California State Dept. of Motor Vehicles, Sacramento.

This handbook is designed to guide California parents in helping their teenagers practice the driving skills required to obtain a driver license. The first section includes information on the following topics: meeting California driver training and licensing requirements, understanding the parent's role as the driving instructor's aide, using the…

Parameters of loop-controlled magnetic rheology drive for segmented large mirror

NASA Astrophysics Data System (ADS)

Deulin, Eugeni A.; Mikhailov, Valeri P.; Eliseev, Oleg N.; Sytchev, Victor V.

2000-07-01

The design, parameters and the amplitude-frequency analysis of the new magnetic rheology (MR) drive are presented. The combination of hydrostatic carrier, MR hydraulic loop control, elastic thin wall seal joined in a single unit ensures small positioning error nm and small time of response T

Driving Procedures. A Resource Guide for Driver Education Teachers.

ERIC Educational Resources Information Center

Texas State Dept. of Public Safety, Austin.

Designed to provide instructors with resource materials for driver education, this book contains mainly materials on established safe driving procedures. An introduction defines a procedure as describing ways in which a driver can comply with the law to do something extra that will increase his/her safety and prevent congestion and collision.…

Safe Driving and Road Signs. Fordson Bilingual Demonstration Project.

ERIC Educational Resources Information Center

Stanyar, Angela

This vocational instructional module on safe driving and road signs is one of eight such modules designed to assist recently arrived Arab students, limited in English proficiency (LEP), in critical instructional areas in a comprehensive high school. Goal stated for this module is for the student preparing for driver's education to recognize,…

Driving Objectives and High-level Requirements for KP-Lab Technologies

ERIC Educational Resources Information Center

Lakkala, Minna; Paavola, Sami; Toikka, Seppo; Bauters, Merja; Markannen, Hannu; de Groot, Reuma; Ben Ami, Zvi; Baurens, Benoit; Jadin, Tanja; Richter, Christoph; Zoserl, Eva; Batatia, Hadj; Paralic, Jan; Babic, Frantisek; Damsa, Crina; Sins, Patrick; Moen, Anne; Norenes, Svein Olav; Bugnon, Alexandra; Karlgren, Klas; Kotzinons, Dimitris

2008-01-01

One of the central goals of the KP-Lab project is to co-design pedagogical methods and technologies for knowledge creation and practice transformation in an integrative and reciprocal manner. In order to facilitate this process user tasks, driving objectives and high-level requirements have been introduced as conceptual tools to mediate between…

Inertial piezoelectric linear motor driven by a single-phase harmonic wave with automatic clamping mechanism

NASA Astrophysics Data System (ADS)

He, Liangguo; Chu, Yuheng; Hao, Sai; Zhao, Xiaoyong; Dong, Yuge; Wang, Yong

2018-05-01

A novel, single-phase, harmonic-driven, inertial piezoelectric linear motor using an automatic clamping mechanism was designed, fabricated, and tested to reduce the sliding friction and simplify the drive mechanism and power supply control of the inertial motor. A piezoelectric bimorph and a flexible hinge were connected in series to form the automatic clamping mechanism. The automatic clamping mechanism was used as the driving and clamping elements. A dynamic simulation by Simulink was performed to prove the feasibility of the motor. The finite element method software COMSOL was used to design the structure of the motor. An experimental setup was built to validate the working principle and evaluate the performance of the motor. The prototype motor outputted a no-load velocity of 3.178 mm/s at a voltage of 220 Vp-p and a maximum traction force of 4.25 N under a preload force of 8 N. The minimum resolution of 1.14 μm was achieved at a driving frequency of 74 Hz, a driving voltage of 50 Vp-p, and a preload force of 0 N.

Drive development for an 10 Mbar Rayleigh-Taylor strength experiment on the National Ignition Facility

NASA Astrophysics Data System (ADS)

Prisbrey, Shon; Park, Hye-Sook; Huntington, Channing; McNaney, James; Smith, Raym; Wehrenberg, Christopher; Swift, Damian; Panas, Cynthia; Lord, Dawn; Arsenlis, Athanasios

2017-10-01

Strength can be inferred by the amount a Rayleigh-Taylor surface deviates from classical growth when subjected to acceleration. If the acceleration is great enough, even materials highly resistant to deformation will flow. We use the National Ignition Facility (NIF) to create an acceleration profile that will cause sample metals, such as Mo or Cu, to reach peak pressures of 10 Mbar without inducing shock melt. To create such a profile we shock release a stepped density reservoir across a large gap with the stagnation of the reservoir on the far side of the gap resulting in the desired pressure drive history. Low density steps (foams) are a necessary part of this design and have been studied in the last several years on the Omega and NIF facilities. We will present computational and experimental progress that has been made on the 10 Mbar drive designs - including recent drive shots carried out at the NIF. This work was performed under the auspices of the Lawrence Livermore National Security, LLC, (LLNS) under Contract No. DE-AC52-07NA27344. LLNL-ABS-734781.

The shape of cars to come

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashley, S.

1991-05-01

Ford's new concept car achieves weight, size, and cost savings with an innovative lightweight aluminum space frame composed of simple extrusions that are fitted together like Lego blocks and adhesively bonded. On the outside, the design is a blend of art and technology that is a modern restatement of a large luxury car. The other major focus of the design is the Contour's compact T-drive powertrain configuration (also shared by the Mystique). This consists of a transversely mounted engine stuffed into the front of the chassis with a longitudinally positioned transmission right behind it. The T-drive arrangement shrinks the car'smore » engine bay and overall length while expanding the passenger compartment. In addition, powerplants with from four to eight cylinders as well as front-wheel-, rear-wheel-, and four-wheel-drive transmission systems can all be incorporated into the T-drive. Other technical innovations on the Contour include an unusual ducted cooling system, a compact brake assembly, a lightweight high-efficiency air conditioner, centralized single-source lighting, and simple but effective suspension technology.« less

Microscopic pick-and-place teleoperation

NASA Astrophysics Data System (ADS)

Bhatti, Pamela; Hannaford, Blake; Marbot, Pierre-Henry

1993-03-01

A three degree-of-freedom direct drive mini robot has been developed for biomedical applications. The design approach of the mini robot relies heavily upon electromechanical components from the Winchester disk drive industry. In the current design, the first joint is driven by actuators from a 5.25' drive, and the following joints are driven by actuators typical of 3.5' drives. The system has 5 - 10 micrometers of position repeatability and resolution in all three axes. A mini gripper attachment has been fabricated for the robot to explore manipulation of objects ranging from 50 micrometers to 500 micrometers . Mounted on the robot, the gripper has successfully performed pick and place operations under teleoperated control. The mini robot serves to precisely position the gripper, and a needle-like finger of the gripper deflects so the fingers can grip a target object. The gripper finger capable of motion is fabricated with a piezoelectric bimorph crystal which deflects with an applied DC voltage. The experimental results are promising, and the mini gripper may be modified for future biomedical and micro assembly applications.

Functional brain mapping of actual car-driving using [18F]FDG-PET.

PubMed

Jeong, Myeonggi; Tashiro, Manabu; Singh, Laxsmi N; Yamaguchi, Keiichiro; Horikawa, Etsuo; Miyake, Masayasu; Watanuki, Shouichi; Iwata, Ren; Fukuda, Hiroshi; Takahashi, Yasuo; Itoh, Masatoshi

2006-11-01

This study aims at identifying the brain activation during actual car-driving on the road, and at comparing the results to those of previous studies on simulated car-driving. Thirty normal volunteers, aged 20 to 56 years, were divided into three subgroups, active driving, passive driving and control groups, for examination by positron emission tomography (PET) and [18F]2-deoxy-2-fluoro-D-glucose (FDG). The active driving subjects (n = 10) drove for 30 minutes on quiet normal roads with a few traffic signals. The passive driving subjects (n = 10) participated as passengers on the front seat. The control subjects (n = 10) remained seated in a lit room with their eyes open. Voxel-based t-statistics were applied using SPM2 to search brain activation among the subgroups mentioned above. Significant brain activation was detected during active driving in the primary and secondary visual cortices, primary sensorimotor areas, premotor area, parietal association area, cingulate gyrus, the parahippocampal gyrus as well as in thalamus and cerebellum. The passive driving manifested a similar-looking activation pattern, lacking activations in the premotor area, cingulate and parahippocampal gyri and thalamus. Direct comparison of the active and passive driving conditions revealed activation in the cerebellum. The result of actual driving looked similar to that of simulated driving, suggesting that visual perception and visuomotor coordination were the main brain functions while driving. In terms of attention and autonomic arousal, however, it seems there was a significant difference between simulated and actual driving possibly due to risk of accidents. Autonomic and emotional aspects of driving should be studied using an actual driving study-design.

Psychometrics of the AAN Caregiver Driving Safety Questionnaire and contributors to caregiver concern about driving safety in older adults.

PubMed

Carvalho, Janessa O; Springate, Beth; Bernier, Rachel A; Davis, Jennifer

2018-03-01

ABSTRACTBackground:The American Academy of Neurology (AAN) updated their practice parameters in the evaluation of driving risk in dementia and developed a Caregiver Driving Safety Questionnaire, detailed in their original manuscript (Iverson Gronseth, Reger, Classen, Dubinsky, & Rizzo, 2010). They described four factors associated with decreased driving ability in dementia patients: history of crashes or citations, informant-reported concerns, reduced mileage, and aggressive driving. An informant-reported AAN Caregiver Driving Safety Questionnaire was designed with these elements, and the current study was the first to explore the factor structure of this questionnaire. Additionally, we examined associations between these factors and cognitive and behavioral measures in patients with mild cognitive impairment or early Alzheimer's disease and their informants. Exploratory factor analysis revealed a four-component structure, consistent with the theory behind the AAN scale composition. These four factor scores also were significantly associated with performance on cognitive screening instruments and informant reported behavioral dysfunction. Regressions revealed that behavioral dysfunction predicted caregiver concerns about driving safety beyond objective patient cognitive dysfunction. In this first known quantitative exploration of the scale, our results support continued use of this scale in office driving safety assessments. Additionally, patient behavioral changes predicted caregiver concerns about driving safety over and above cognitive status, which suggests that caregivers may benefit from psychoeducation about cognitive factors that may negatively impact driving safety.

Why do drivers become safer over the first three months of driving? A longitudinal qualitative study.

PubMed

Day, Marianne R; Thompson, Andrew R; Poulter, Damian R; Stride, Christopher B; Rowe, Richard

2018-08-01

Drivers are at high crash risk when they begin independent driving, with liability decreasing steeply over the first three months. Their behavioural development, and other changes underlying improved safety are not well understood. We adopted an innovative longitudinal qualitative design, with thirteen newly qualified drivers completing a total of 36 semi-structured interviews, one, two and three months after acquiring a full UK driving license. The interviews probed high-risk factors for new drivers, as well as allowing space for generating novel road safety issues. Analysis adopted a dual deductive and inductive interpretative thematic approach, identifying three super-ordinate themes: (1) Improvements in car control skills and situation awareness; (2) A reduction in the thrill of taking risks when driving against a background of generally increasing driving speed; (3) Early concerns about their social status in the eyes of other road users during the early stages of driving, which may put pressure on them to drive faster than they felt comfortable with. The study provides important new leads towards understanding how novice driving becomes safer over the first few months of driving, including how well-studied concepts of driving skill and style may change during development of independent driving, and bringing the less rigorously studied concept of social status into focus. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Driving behavior recognition using EEG data from a simulated car-following experiment.

PubMed

Yang, Liu; Ma, Rui; Zhang, H Michael; Guan, Wei; Jiang, Shixiong

2018-07-01

Driving behavior recognition is the foundation of driver assistance systems, with potential applications in automated driving systems. Most prevailing studies have used subjective questionnaire data and objective driving data to classify driving behaviors, while few studies have used physiological signals such as electroencephalography (EEG) to gather data. To bridge this gap, this paper proposes a two-layer learning method for driving behavior recognition using EEG data. A simulated car-following driving experiment was designed and conducted to simultaneously collect data on the driving behaviors and EEG data of drivers. The proposed learning method consists of two layers. In Layer I, two-dimensional driving behavior features representing driving style and stability were selected and extracted from raw driving behavior data using K-means and support vector machine recursive feature elimination. Five groups of driving behaviors were classified based on these two-dimensional driving behavior features. In Layer II, the classification results from Layer I were utilized as inputs to generate a k-Nearest-Neighbor classifier identifying driving behavior groups using EEG data. Using independent component analysis, a fast Fourier transformation, and linear discriminant analysis sequentially, the raw EEG signals were processed to extract two core EEG features. Classifier performance was enhanced using the adaptive synthetic sampling approach. A leave-one-subject-out cross validation was conducted. The results showed that the average classification accuracy for all tested traffic states was 69.5% and the highest accuracy reached 83.5%, suggesting a significant correlation between EEG patterns and car-following behavior. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husain, Tausif; Hasan, Iftekhar; Sozer, Yilmaz

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The TFM has a modular structure with quasi-U stator cores and ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating arrangement to achieve high air gap flux density. The design considerations for this TFM with respect to initial sizing, pole number selection, key design ratios, and pole shaping are presented in this paper. Pole number selection is critical in the design process of a TFM because it affects both the torque density and power factor under fixed magnetic andmore » changing electrical loading. Several key design ratios are introduced to facilitate the design procedure. The effect of pole shaping on back-emf and inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis. A prototype is under construction for experimental verification.« less

LDRD Final Report: Advanced Hohlraum Concepts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, Ogden S.

Indirect drive inertial confinement fusion (ICF) experiments to date have mostly used cylindrical, laser-heated, gas-filled hohlraums to produce the radiation drive needed to symmetrically implode DT-filled fusion capsules. These hohlraums have generally been unable to produce a symmetric radiation drive through the end of the desired drive pulse, and are plagued with complications due to laser-plasma interactions (LPI) that have made it difficult to predict their performance. In this project we developed several alternate hohlraum concepts. These new hohlraums utilize different hohlraum geometries, radiation shields, and foam materials in an attempt to improve performance relative to cylindrical hohlraums. Each alternatemore » design was optimized using radiation hydrodynamic (RH) design codes to implode a reference DT capsule with a high-density carbon (HDC) ablator. The laser power and energy required to produce the desired time-dependent radiation drive, and the resulting time-dependent radiation symmetry for each new concept were compared to the results for a reference cylindrical hohlraum. Since several of the new designs needed extra laser entrance holes (LEHs), techniques to keep small LEHs open longer, including high-Z foam liners and low-Z wires at the LEH axis, were investigated numerically. Supporting experiments and target fabrication efforts were also done as part of this project. On the Janus laser facility plastic tubes open at one end (halfraums) and filled with SiO 2 or Ta 2O 5 foam were heated with a single 2w laser. Laser propagation and backscatter were measured. Generally the measured propagation was slower than calculated, and the measured laser backscatter was less than calculated. A comparable, scaled up experiment was designed for the NIF facility and four targets were built. Since low density gold foam was identified as a desirable material for lining the LEH and the hohlraum wall, a technique was developed to produce 550 mg/cc gold foam, and a sample of this material was successfully manufactured.« less

Team Based Engineering Design Thinking

ERIC Educational Resources Information Center

Mentzer, Nathan

2012-01-01

The objective of this research was to explore design thinking among teams of high school students. This objective is encompassed in the research question driving this inquiry: How do teams of high school students allocate time across stages of design? Design thinking on the professional level typically occurs in a team environment. Many…

Highly loaded multi-stage fan drive turbine: Plain blade configuration design

NASA Technical Reports Server (NTRS)

Evans, D. C.; Wolfmeyer, G. W.

1972-01-01

The constant-inside-diameter flowpath was scaled for testing in an existing turbine test facility. Blading detailed design is discussed, and design data are summarized. Predicted performance maps are presented. Steady-state stresses and vibratory behavior are discussed and the results of the mechanical design analysis are presented.

Team Based Engineering Design Thinking

ERIC Educational Resources Information Center

Mentzer, Nathan

2014-01-01

The objective of this research was to explore design thinking among teams of high school students. This objective was encompassed in the research question driving the inquiry: How do teams of high school students allocate time across stages of design? Design thinking on the professional level typically occurs in a team environment. Many…

Strength Analysis and Reliability Evaluation for Speed Reducers

NASA Astrophysics Data System (ADS)

Tsai, Yuo-Tern; Hsu, Yung-Yuan

2017-09-01

This paper studies the structural stresses of differential drive (DD) and harmonic drive (HD) for design improvement of reducers. The designed principles of the two reducers are reported for function comparison. The critical components of the reducers are constructed for performing motion simulation and stress analysis. DD is designed based on differential displacement of the decelerated gear ring as well as HD on a flexible spline. Finite element method (FEM) is used to analyze the structural stresses including the dynamic properties of the reducers. The stresses including kinematic properties of the two reducers are compared to observe the properties of the designs. The analyzed results are applied to identify the allowable loads of the reducers in use. The reliabilities of the reducers in different loads are further calculated according to the variation of stress. The studied results are useful on engineering analysis and reliability evaluation for designing a speed reducer with high ratios.

LLE Review Quarterly Report January - March 2012. Volume 130

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shvydky, Alex

2012-03-01

This volume of the LLE Review, covering January–March 2012, features “OMEGA Polar-Drive Target Designs,” by P. B. Radha, J. A. Marozas, F. J. Marshall, A. Shvydky, T. J. B. Collins, V. N. Goncharov, R. L. McCrory, P. W. McKenty, D. D. Meyerhofer, T. C. Sangster, and S. Skupsky. This article (p. 57) describes low-adiabat, cryogenic-deuterium–tritium, and warm-plastic-shell polar-drive (PD)–implosion designs for the OMEGA laser. The designs are at two different on-target laser intensities, each at a different in-flight aspect ratio (IFAR). The first design permits one to study implosion energetics and target performance closer to ignition-relevant intensities (7 X 10more » 14 W/cm 2 at the quarter-critical surface), where nonlocal heat conduction and laser–plasma interactions can play an important role, but at lower values of IFAR (~22). The second design permits one to study implosion energetics and target performance at a lower intensity (3 X 10 14 W/cm 2) but at higher IFAR (~32), where the shell instability can play an important role. The higher IFAR designs are accessible on the existing OMEGA Laser System only at lower intensities. Implosions at ignition-relevant intensities can be obtained only by reducing target radius, although only at smaller values of IFAR. Polar-drive geometry requires repointing the laser beams to improve shell symmetry. The higher-intensity designs optimize target performance by repointing beams to a lesser extent and compensate for the reduced equatorial drive by increasing beam energies for the repointed beams and using custom beam profiles that improve equatorial illumination at the expense of irradiation at higher latitudes. These designs will be studied when new phase plates for the OMEGA Laser System, corresponding to the smaller target radii and custom beam profiles, are obtained. Implosion results from the combined set of high-intensity and high-IFAR implosions should yield valuable data to validate models of laser-energy deposition, heat conduction, nonuniformity growth, and fuel assembly in PD geometry.« less

Designing Fatigue Warning Systems: The perspective of professional drivers.

PubMed

Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Peng, Qijia; Li, Musen; Wang, Chunhui; Zhang, Wei

2016-03-01

Professional drivers have been characterized as experiencing heavy fatigue resulting from long driving time in their daily work. This study aimed to explore the potential demand of Fatigue Warning Systems (FWSs) among professional drivers as a means of reducing the danger of fatigue driving and to examine their opinions regarding the design of FWSs. Six focus groups with 35 participants and a questionnaire survey with 600 respondents were conducted among Chinese truck and taxi drivers to collect qualitative and quantitative data concerning the current situation of fatigue driving and opinions regarding the design of FWSs. The results revealed that both truck and taxi drivers had a positive attitude toward FWSs, and they hoped this system could not only monitor and warn them regarding their fatigue but also somewhat relieve their fatigue before they could stop and rest. As for warning signals, participants preferred auditory warnings, as opposed to visual, vibrotactile or electric stimuli. Interestingly, it was proposed that verbal warnings involving the information regarding consequences of fatigue driving or the wishes of drivers' family members would be more effective. Additionally, different warning patterns, including graded, single and continuous warnings, were discussed in the focus group. Finally, the participants proposed many other suggestions, as well as their concerns regarding FWSs, which will provide valuable information for companies who wish to develop FWSs for professional drivers. Copyright © 2015. Published by Elsevier Ltd.

Experimental examination of the effects of televised motor vehicle commercials on risk-positive attitudes, emotions and risky driving inclinations.

PubMed

Vingilis, Evelyn; Roseborough, James E W; Wiesenthal, David L; Vingilis-Jaremko, Larissa; Nuzzo, Valentina; Fischer, Peter; Mann, Robert E

2015-02-01

This study examined the short-term effects of risky driving motor vehicle television commercials on risk-positive attitudes, emotions and risky driving inclinations in video-simulated critical road traffic situations among males and females, within an experimental design. Participants were randomly assigned to one of three televised commercial advertising conditions embedded in a television show: a risky driving motor vehicle commercial condition, a non-risky driving motor vehicle commercial condition and a control non-motor vehicle commercial condition. Participants subsequently completed the Implicit Attitude Test (IAT) to measure risk-positive attitudes, Driver Thrill Seeking Scale (DTSS) to measure risk-positive emotions and the Vienna Risk-Taking Test - Traffic (WRBTV) to measure risky driving inclinations. ANOVA analyses indicated that type of commercial participants watched did not affect their performance on the IAT, DTSS or WRBTV. However, a main effect of heightened risk-positive emotions and risky driving inclinations was found for males. Despite public and governmental concern that risky driving motor vehicle commercials may increase the likelihood that people exposed to these commercials engage in risky driving, this experimental study found no immediate effect of brief exposure to a risky driving motor vehicle commercial on risk-positive attitudes, emotions or risky driving inclinations. Subsequent research should examine the effects of cumulative exposure to risky driving motor vehicle television commercials and print advertisements. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fatigue in Younger and Older Drivers: Effectiveness of an Alertness-Maintaining Task.

PubMed

Song, Woojin; Woon, Fu L; Doong, Alice; Persad, Carol; Tijerina, Louis; Pandit, Pooja; Cline, Carol; Giordani, Bruno

2017-09-01

The aim of this study was to examine the effects of an alertness-maintaining task (AMT) in older, fatigued drivers. Fatigue during driving increases crash risk, and previous research suggests that alertness and driving in younger adults may be improved using a secondary AMT during boring, fatigue-eliciting drives. However, the potential impact of an AMT on driving has not been investigated in older drivers whose ability to complete dual tasks has been shown to decline and therefore may be negatively affected with an AMT in driving. Younger ( n = 29) and older drivers ( n = 39) participated in a 50-minute simulated drive designed to induce fatigue, followed by four 10-minute sessions alternating between driving with and without an AMT. Younger drivers were significantly more affected by fatigue on driving performance than were older drivers but benefitted significantly from the AMT. Older drivers did not demonstrate increased driver errors with fatigue, and driving did not deteriorate significantly during participation in the AMT condition, although their speed was significantly more variable with the AMT. Consistent with earlier research, an AMT applied during fatiguing driving is effective in improving alertness and reducing driving errors in younger drivers. Importantly, older drivers were relatively unaffected by fatigue, and use of an AMT did not detrimentally affect their driving performance. These results support the potential use of an AMT as a new automotive technology to improve fatigue and promote driver safety, though the benefits of such technology may differ between different age groups.

Possession attachment predicts cell phone use while driving.

PubMed

Weller, Joshua A; Shackleford, Crystal; Dieckmann, Nathan; Slovic, Paul

2013-04-01

Distracted driving has become an important public health concern. However, little is known about the predictors of this health-risking behavior. One overlooked risk factor for distracted driving is the perceived attachment that one feels toward his or her phone. Prior research has suggested that individuals develop bonds toward objects, and qualitative research suggests that the bond between young drivers and their phones can be strong. It follows that individuals who perceive a strong attachment to their phone would be more likely to use it, even when driving. In a nationally representative sample of young drivers (17-28 years), participants (n = 1,006) completed a survey about driving behaviors and phone use. Risk perception surrounding cell phone use while driving and perceived attachment to one's phone were assessed by administering factor-analytically derived scales that were created as part of a larger project. Attachment toward one's phone predicted the proportion of trips in which a participant reported using their cell phone while driving, beyond that accounted for by risk perception and overall phone use. Further, attachment predicted self-reported distracted driving behaviors, such as the use of social media while driving. Attachment to one's phone may be an important but overlooked risk factor for the engagement of potentially health-risking driving behaviors. Understanding that phone attachment may adversely affect driving behaviors has the potential to inform prevention and intervention efforts designed to reduce distracted driving behaviors, especially in young drivers. 2013 APA, all rights reserved

Modeling of Autovariator Operation as Power Components Adjuster in Adaptive Machine Drives

NASA Astrophysics Data System (ADS)

Balakin, P. D.; Belkov, V. N.; Shtripling, L. O.

2018-01-01

Full application of the available power and stationary mode preservation for the power station (engine) operation of the transport machine under the conditions of variable external loading, are topical issues. The issues solution is possible by means of mechanical drives with the autovaried rate transfer function and nonholonomic constraint of the main driving mediums. Additional to the main motion, controlled motion of the driving mediums is formed by a variable part of the transformed power flow and is implemented by the integrated control loop, functioning only on the basis of the laws of motion. The mathematical model of the mechanical autovariator operation is developed using Gibbs function, acceleration energy; the study results are presented; on their basis, the design calculations of the autovariator driving mediums and constraints, including its automatic control loop, are possible.

Development of a drive system for a sequential space camera

NASA Technical Reports Server (NTRS)

Sharpsteen, J. T.; Solheim, C. D.; Stoap, L. J.

1976-01-01

Breadboard models of single and dual motor drives for the shutter, claw and magazine of a space camera system were designed and tested. The single motor technique utilizes a single electronically commutated motor to drive the claw and shutter without resorting to a solenoid actuated clutch for pulse operation. Shutter speed is established by a combination of the cinemode speed and the opening of the conventional DAC two piece shutter. Pulse mode operation is obtained by applying power at a fixed clock rate and removing power at an appropriate point in the mechanical cycle such that the motor comes to rest by system friction. The dual motor approach utilizes a stepper motor to drive the shutter and an electronically commutated dc motor to drive the claw and magazine functions. The motors are synchronized electronically.

CRISPR/Cas9 gene drives in genetically variable and nonrandomly mating wild populations

PubMed Central

Drury, Douglas W.; Dapper, Amy L.; Siniard, Dylan J.; Zentner, Gabriel E.; Wade, Michael J.

2017-01-01

Synthetic gene drives based on CRISPR/Cas9 have the potential to control, alter, or suppress populations of crop pests and disease vectors, but it is unclear how they will function in wild populations. Using genetic data from four populations of the flour beetle Tribolium castaneum, we show that most populations harbor genetic variants in Cas9 target sites, some of which would render them immune to drive (ITD). We show that even a rare ITD allele can reduce or eliminate the efficacy of a CRISPR/Cas9-based synthetic gene drive. This effect is equivalent to and accentuated by mild inbreeding, which is a characteristic of many disease-vectoring arthropods. We conclude that designing such drives will require characterization of genetic variability and the mating system within and among targeted populations. PMID:28560324

CRISPR/Cas9 gene drives in genetically variable and nonrandomly mating wild populations.

PubMed

Drury, Douglas W; Dapper, Amy L; Siniard, Dylan J; Zentner, Gabriel E; Wade, Michael J

2017-05-01

Synthetic gene drives based on CRISPR/Cas9 have the potential to control, alter, or suppress populations of crop pests and disease vectors, but it is unclear how they will function in wild populations. Using genetic data from four populations of the flour beetle Tribolium castaneum , we show that most populations harbor genetic variants in Cas9 target sites, some of which would render them immune to drive (ITD). We show that even a rare ITD allele can reduce or eliminate the efficacy of a CRISPR/Cas9-based synthetic gene drive. This effect is equivalent to and accentuated by mild inbreeding, which is a characteristic of many disease-vectoring arthropods. We conclude that designing such drives will require characterization of genetic variability and the mating system within and among targeted populations.

A New Dual-Frequency Liquid Crystal Lens with Ring-and-Pie Electrodes and a Driving Scheme to Prevent Disclination Lines and Improve Recovery Time

PubMed Central

Kao, Yung-Yuan; Chao, Paul C.-P.

2011-01-01

A new liquid crystal lens design is proposed to improve the recovery time with a ring-and-pie electrode pattern through a suitable driving scheme and using dual-frequency liquid crystals (DFLC) MLC-2048. Compared with the conventional single hole-type liquid crystal lens, this new structure of the DFLC lens is composed of only two ITO glasses, one of which is designed with the ring-and-pie pattern. For this device, one can control the orientation of liquid crystal directors via a three-stage switching procedure on the particularly-designed ring-and-pie electrode pattern. This aims to eliminate the disclination lines, and using different drive frequencies to reduce the recovery time to be less than 5 seconds. The proposed DFLC lens is shown effective in reducing recovery time, and then serves well as a potential device in places of the conventional lenses with fixed focus lengths and the conventional LC lens with a single circular-hole electrode pattern. PMID:22163906

Design and testing of the reactor-internal hydraulic control rod drive for the nuclear heating plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batheja, P.; Meier, W.J.; Rau, P.J.

A hydraulically driven control rod is being developed at Kraftwerk Union for integration in the primary system of a small nuclear district heating reactor. An elaborate test program, under way for --3 yr, was initiated with a plexiglass rig to understand the basic principles. A design specification list was prepared, taking reactor boundary conditions and relevant German rules and regulations into account. Subsequently, an atmospheric loop for testing of components at 20 to 90/sup 0/C was erected. The objectives involved optimization of individual components such as a piston/cylinder drive unit, electromagnetic valves, and an ultrasonic position indication system as wellmore » as verification of computer codes. Based on the results obtained, full-scale components were designed and fabricated for a prototype test rig, which is currently in operation. Thus far, all atmospheric tests in this rig have been completed. Investigations under reactor temperature and pressure, followed by endurance tests, are under way. All tests to date have shown a reliable functioning of the hydraulic drive, including a novel ultrasonic position indication system.« less

Modelling and control system of multi motor conveyor

NASA Astrophysics Data System (ADS)

Kovalchuk, M. S.; Baburin, S. V.

2018-03-01

The paper deals with the actual problem of developing the mathematical model of electromechanical system: conveyor – multimotor electric drive with a frequency converter, with the implementation in Simulink/MatLab, which allows one to perform studies of conveyor operation modes, taking into account the specifics of the mechanism with different electric drives control algorithms. The authors designed the mathematical models of the conveyor and its control system that provides increased uniformity of load distribution between drive motors and restriction of dynamic loads on the belt (over-regulation until 15%).

Floquet-Network Theory of Nonreciprocal Transport

NASA Astrophysics Data System (ADS)

Li, Huanan; Kottos, Tsampikos; Shapiro, Boris

2018-04-01

We develop a theoretical framework that lays out the fundamental rules under which a periodic (Floquet) driving scheme can induce nonreciprocal transport. Our approach utilizes an extended Hilbert space where a Floquet network with an extra (frequency) dimension naturally arises. The properties of this network (its on-site potential and the intersite couplings) are in one-to-one correspondence with the initial driving scheme. Its proper design allows for a control of the multipath scattering processes and the associated interferences. We harness this degree of freedom to realize driving schemes with narrow-band or broadband nonreciprocal transport.

Finite-time hybrid projective synchronization of the drive-response complex networks with distributed-delay via adaptive intermittent control

NASA Astrophysics Data System (ADS)

Cheng, Lin; Yang, Yongqing; Li, Li; Sui, Xin

2018-06-01

This paper studies the finite-time hybrid projective synchronization of the drive-response complex networks. In the model, general transmission delays and distributed delays are also considered. By designing the adaptive intermittent controllers, the response network can achieve hybrid projective synchronization with the drive system in finite time. Based on finite-time stability theory and several differential inequalities, some simple finite-time hybrid projective synchronization criteria are derived. Two numerical examples are given to illustrate the effectiveness of the proposed method.

New ergonomic headset for Tongue-Drive System with wireless smartphone interface.

PubMed

Park, Hangue; Kim, Jeonghee; Huo, Xueliang; Hwang, In-O; Ghovanloo, Maysam

2011-01-01

Tongue Drive System (TDS) is a wireless tongue-operated assistive technology (AT), developed for people with severe physical disabilities to control their environment using their tongue motion. We have developed a new ergonomic headset for the TDS with a user-friendly smartphone interface, through which users will be able to wirelessly control various devices, access computers, and drive wheelchairs. This headset design is expected to act as a flexible and multifunctional communication interface for the TDS and improve its usability, accessibility, aesthetics, and convenience for the end users.

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies. [various hybrid/electric power train configurations and electrical and mechanical drive-line components

NASA Technical Reports Server (NTRS)

1979-01-01

The relative attractiveness of various hybrid/electric power train configurations and electrical and mechanical drive-line components was studied. The initial screening was concerned primarily with total vehicle weight and economic factors and identified the hybrid power train combinations which warranted detailed evaluation over various driving cycles. This was done using a second-by-second vehicle simulation program which permitted the calculations of fuel economy, electricity usage, and emissions as a function of distance traveled in urban and highway driving. Power train arrangement possibilities were examined in terms of their effect on vehicle handling, safety, serviceability, and passenger comfort. A dc electric drive system utilizing a separately excited motor with field control and battery switching was selected for the near term hybrid vehicle. Hybrid vehicle simulations showed that for the first 30 mi (the electric range of the vehicle) in urban driving, the fuel economy was 80 mpg using a gasoline engine and 100 mpg using a diesel engine. In urban driving the hybrid would save about 75% of the fuel used by the conventional vehicle and in combined urban/highway driving the fuel saving is about 50%.

Safe driving in a green world: a review of driver performance benchmarks and technologies to support 'smart' driving.

PubMed

Young, Mark S; Birrell, Stewart A; Stanton, Neville A

2011-05-01

Road transport is a significant source of both safety and environmental concerns. With climate change and fuel prices increasingly prominent on social and political agendas, many drivers are turning their thoughts to fuel efficient or 'green' (i.e., environmentally friendly) driving practices. Many vehicle manufacturers are satisfying this demand by offering green driving feedback or advice tools. However, there is a legitimate concern regarding the effects of such devices on road safety--both from the point of view of change in driving styles, as well as potential distraction caused by the in-vehicle feedback. In this paper, we appraise the benchmarks for safe and green driving, concluding that whilst they largely overlap, there are some specific circumstances in which the goals are in conflict. We go on to review current and emerging in-vehicle information systems which purport to affect safe and/or green driving, and discuss some fundamental ergonomics principles for the design of such devices. The results of the review are being used in the Foot-LITE project, aimed at developing a system to encourage 'smart'--that is safe and green--driving. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Intentions and willingness to drive while drowsy among university students: An application of an extended theory of planned behavior model.

PubMed

Lee, Clark J; Geiger-Brown, Jeanne; Beck, Kenneth H

2016-08-01

A web-based questionnaire was used to assess the utility of constructs from the Theory of Planned Behavior (TPB) and the Prototype Willingness Model (PWM) to predict intentions and willingness to engage in drowsy driving in a sample of 450 university students. Those students who reported more favorable attitudes and subjective norm and greater perceived control and willingness in relation to drowsy driving behavior were more likely to report stronger intentions to engage in drowsy driving behavior. Augmenting the TPB constructs with the PWM construct of willingness significantly explained up to an additional 8 percent of the variance in drowsy driving intention. Perceived behavioral control and willingness were consistently the strongest predictors of drowsy driving intention in the augmented model, which together with the control (personal) variables explained up to 70 percent of the variance in intention. Thus, the Theory of Planned Behavior and the Prototype Willingness Model may be useful for understanding motivational influences on drowsy driving behavior in young people and present promising theoretical frameworks for designing more effective interventions against drowsy driving in this population. Copyright © 2016 Elsevier Ltd. All rights reserved.

Vision-related fitness to drive mobility scooters: A practical driving test.

PubMed

Cordes, Christina; Heutink, Joost; Tucha, Oliver M; Brookhuis, Karel A; Brouwer, Wiebo H; Melis-Dankers, Bart J M

2017-03-06

To investigate practical fitness to drive mobility scooters, comparing visually impaired participants with healthy controls. Between-subjects design. Forty-six visually impaired (13 with very low visual acuity, 10 with low visual acuity, 11 with peripheral field defects, 12 with multiple visual impairment) and 35 normal-sighted controls. Participants completed a practical mobility scooter test-drive, which was recorded on video. Two independent occupational therapists specialized in orientation and mobility evaluated the videos systematically. Approximately 90% of the visually impaired participants passed the driving test. On average, participants with visual impairments performed worse than normal-sighted controls, but were judged sufficiently safe. In particular, difficulties were observed in participants with peripheral visual field defects and those with a combination of low visual acuity and visual field defects. People with visual impairment are, in practice, fit to drive mobility scooters; thus visual impairment on its own should not be viewed as a determinant of safety to drive mobility scooters. However, special attention should be paid to individuals with visual field defects with or without a combined low visual acuity. The use of an individual practical fitness-to-drive test is advised.

Personality and attitudes as predictors of risky driving among older drivers.

PubMed

Lucidi, Fabio; Mallia, Luca; Lazuras, Lambros; Violani, Cristiano

2014-11-01

Although there are several studies on the effects of personality and attitudes on risky driving among young drivers, related research in older drivers is scarce. The present study assessed a model of personality-attitudes-risky driving in a large sample of active older drivers. A cross-sectional design was used, and structured and anonymous questionnaires were completed by 485 older Italian drivers (Mean age=68.1, SD=6.2, 61.2% males). The measures included personality traits, attitudes toward traffic safety, risky driving (errors, lapses, and traffic violations), and self-reported crash involvement and number of issued traffic tickets in the last 12 months. Structural equation modeling showed that personality traits predicted both directly and indirectly traffic violations, errors, and lapses. More positive attitudes toward traffic safety negatively predicted risky driving. In turn, risky driving was positively related to self-reported crash involvement and higher number of issued traffic tickets. Our findings suggest that theoretical models developed to account for risky driving of younger drivers may also apply in the older drivers, and accordingly be used to inform safe driving interventions for this age group. Copyright © 2014 Elsevier Ltd. All rights reserved.

The ARTEMIS European driving cycles for measuring car pollutant emissions.

PubMed

André, Michel

2004-12-01

In the past 10 years, various work has been undertaken to collect data on the actual driving of European cars and to derive representative real-world driving cycles. A compilation and synthesis of this work is provided in this paper. In the frame of the European research project: ARTEMIS, this work has been considered to derive a set of reference driving cycles. The main objectives were as follows: to derive a common set of reference real-world driving cycles to be used in the frame of the ARTEMIS project but also in the frame of on-going national campaigns of pollutant emission measurements, to ensure the compatibility and integration of all the resulting emission data in the European systems of emission inventory; to ensure and validate the representativity of the database and driving cycles by comparing and taking into account all the available data regarding driving conditions; to include in three real-world driving cycles (urban, rural road and motorway) the diversity of the observed driving conditions, within sub-cycles allowing a disaggregation of the emissions according to more specific driving conditions (congested and free-flow urban). Such driving cycles present a real advantage as they are derived from a large database, using a methodology that was widely discussed and approved. In the main, these ARTEMIS driving cycles were designed using the available data, and the method of analysis was based to some extent on previous work. Specific steps were implemented. The study includes characterisation of driving conditions and vehicle uses. Starting conditions and gearbox use are also taken into account.

Fuel consumption for various driving styles in conventional and hybrid electric vehicles: Integrating driving cycle predictions with fuel consumption optimization

DOE PAGES

Rios-Torres, Jackeline; Liu, Jun; Khattak, Asad

2018-06-14

Here, improving fuel economy and lowering emissions are key societal goals. Standard driving cycles, pre-designed by the US Environmental Protection Agency (EPA), have long been used to estimate vehicle fuel economy in laboratory-controlled conditions. They have also been used to test and tune different energy management strategies for hybrid electric vehicles (HEVs). This paper aims to estimate fuel consumption for a conventional vehicle and a HEV using personalized driving cycles extracted from real-world data to study the effects of different driving styles and vehicle types on fuel consumption when compared to the estimates based on standard driving cycles. To domore » this, we extracted driving cycles for conventional vehicles and HEVs from a large-scale U.S. survey that contains real-world GPS-based driving records. Next, the driving cycles were assigned to one of three categories: volatile, normal, or calm. Then, the driving cycles were used along with a driver-vehicle simulation that captures driver decisions (vehicle speed during a trip), powertrain, and vehicle dynamics to estimate fuel consumption for conventional vehicles and HEVs with power-split powertrain. To further optimize fuel consumption for HEVs, the Equivalent Consumption Minimization Strategy (ECMS) is applied. The results show that depending on the driving style and the driving scenario, conventional vehicle fuel consumption can vary widely compared with standard EPA driving cycles. Specifically, conventional vehicle fuel consumption was 13% lower in calm urban driving, but almost 34% higher for volatile highway driving compared with standard EPA driving cycles. Interestingly, when a driving cycle is predicted based on the application of case-based reasoning and used to tune the power distribution in a hybrid electric vehicle, its fuel consumption can be reduced by up to 12% in urban driving. Implications and limitations of the findings are discussed.« less

Fuel consumption for various driving styles in conventional and hybrid electric vehicles: Integrating driving cycle predictions with fuel consumption optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rios-Torres, Jackeline; Liu, Jun; Khattak, Asad

Here, improving fuel economy and lowering emissions are key societal goals. Standard driving cycles, pre-designed by the US Environmental Protection Agency (EPA), have long been used to estimate vehicle fuel economy in laboratory-controlled conditions. They have also been used to test and tune different energy management strategies for hybrid electric vehicles (HEVs). This paper aims to estimate fuel consumption for a conventional vehicle and a HEV using personalized driving cycles extracted from real-world data to study the effects of different driving styles and vehicle types on fuel consumption when compared to the estimates based on standard driving cycles. To domore » this, we extracted driving cycles for conventional vehicles and HEVs from a large-scale U.S. survey that contains real-world GPS-based driving records. Next, the driving cycles were assigned to one of three categories: volatile, normal, or calm. Then, the driving cycles were used along with a driver-vehicle simulation that captures driver decisions (vehicle speed during a trip), powertrain, and vehicle dynamics to estimate fuel consumption for conventional vehicles and HEVs with power-split powertrain. To further optimize fuel consumption for HEVs, the Equivalent Consumption Minimization Strategy (ECMS) is applied. The results show that depending on the driving style and the driving scenario, conventional vehicle fuel consumption can vary widely compared with standard EPA driving cycles. Specifically, conventional vehicle fuel consumption was 13% lower in calm urban driving, but almost 34% higher for volatile highway driving compared with standard EPA driving cycles. Interestingly, when a driving cycle is predicted based on the application of case-based reasoning and used to tune the power distribution in a hybrid electric vehicle, its fuel consumption can be reduced by up to 12% in urban driving. Implications and limitations of the findings are discussed.« less

Bidirectional DC/DC Converter

NASA Astrophysics Data System (ADS)

Pedersen, F.

2008-09-01

The presented bidirectional DC/DC converter design concept is a further development of an already existing converter used for low battery voltage operation.For low battery voltage operation a high efficient low parts count DC/DC converter was developed, and used in a satellite for the battery charge and battery discharge function.The converter consists in a bidirectional, non regulating DC/DC converter connected to a discharge regulating Buck converter and a charge regulating Buck converter.The Bidirectional non regulating DC/DC converter performs with relatively high efficiency even at relatively high currents, which here means up to 35Amps.This performance was obtained through the use of power MOSFET's with on- resistances of only a few mille Ohms connected to a special transformer allowing paralleling several transistor stages on the low voltage side of the transformer. The design is patent protected. Synchronous rectification leads to high efficiency at the low battery voltages considered, which was in the range 2,7- 4,3 Volt DC.The converter performs with low switching losses as zero voltage zero current switching is implemented in all switching positions of the converter.Now, the drive power needed, to switch a relatively large number of low Ohm , hence high drive capacitance, power MOSFET's using conventional drive techniques would limit the overall conversion efficiency.Therefore a resonant drive consuming considerable less power than a conventional drive circuit was implemented in the converter.To the originally built and patent protected bidirectional non regulating DC/DC converter, is added the functionality of regulation.Hereby the need for additional converter stages in form of a Charge Buck regulator and a Discharge Buck regulator is eliminated.The bidirectional DC/DC converter can be used in connection with batteries, motors, etc, where the bidirectional feature, simple design and high performance may be useful.

Drivers who self-estimate lower blood alcohol concentrations are riskier drivers after drinking.

PubMed

Laude, Jennifer R; Fillmore, Mark T

2016-04-01

Alcohol increases the tendency for risky driving in some individuals but not others. Little is known about the factors underlying this individual difference. Studies find that those who underestimate their blood alcohol concentration (BAC) following a dose of alcohol tend to be more impulsive and report greater willingness to drive after drinking than those who estimate their BACs to be greater than their actual BAC. BAC underestimation could contribute to risky driving behavior following alcohol as such drivers might perceive little impairment in their driving ability and thus no need for caution. This study was designed to test the relationship between drivers' BAC estimations following a dose of alcohol or a placebo and the degree of risky driving they displayed during a simulated driving test. Forty adult drivers performed a simulated driving test and estimated their blood alcohol concentration after receiving a dose of alcohol (0.65 g/kg for men and 0.56 g/kg for women) or a placebo. Alcohol increased risk-taking and impaired driving skill. Those who estimated their BAC to be lower were the riskiest drivers following both alcohol and placebo. The tendency to estimate lower BACs could support a series of high-risk decisions, regardless of one's actual BAC. This could include the decision to drive after drinking.

Candidate Coatings and Dry Traction Drives for Planetary Vehicles

NASA Technical Reports Server (NTRS)

Fusaro, Robert; Oswald, Fred B.

2002-01-01

Robert Fusaro and Fred Oswald of the Mechanical Components Branch discussed 'Candidate Coatings and Dry Traction Drives for Planetary Vehicles'. Vehicles to be designed for exploration of planets and moons of the solar system will require reliable mechanical drives to operate efficiently. Long-term operation of these drives will be challenging because of extreme operating conditions. These extreme conditions include: very high and/or very cold temperatures, wide temperature ranges, dust, vacuum or low-pressure atmospheres, and corrosive environments. Most drives used on Earth involve oil-lubricated gears. However, due to the extreme conditions on planetary surfaces, it may not be advisable or even possible to use oil lubrication. Unfortunately, solid lubricants do not work well when applied to gears because of the high contact stress conditions and large sliding motion between the teeth, which cause wear and limit life. We believe traction drives will provide an attractive alternative to gear drives. Traction drives are composed of rollers that provide geometry more conducive to solid lubrication. Minimal slip occurs in this contact geometry and thus there is very low wear to the solid lubricant. The challenge for these solid-lubricated drives is finding materials or coatings that provide the required long-life while also providing high traction. We seek materials that provide low wear with high friction.

Driving performance and driver discomfort in an elevated and standard driving position during a driving simulation.

PubMed

Smith, Jordan; Mansfield, Neil; Gyi, Diane; Pagett, Mark; Bateman, Bob

2015-07-01

The primary purposes of a vehicle driver's seat, is to allow them to complete the driving task comfortably and safely. Within each class of vehicle (e.g. passenger, commercial, industrial, agricultural), there is an expected driving position to which a vehicle cabin is designed. This paper reports a study that compares two driving positions, in relation to Light Commercial Vehicles (LCVs), in terms of driver performance and driver discomfort. In the 'elevated' driving position, the seat is higher than usually used in road vehicles; this is compared to a standard driving position replicating the layout for a commercially available vehicle. It is shown that for a sample of 12 drivers, the elevated position did not, in general, show more discomfort than the standard position over a 60 min driving simulation, although discomfort increased with duration. There were no adverse effects shown for emergency stop reaction time or for driver headway for the elevated posture compared to the standard posture. The only body part that showed greater discomfort for the elevated posture compared to the standard posture was the right ankle. A second experiment confirmed that for 12 subjects, a higher pedal stiffness eliminated the ankle discomfort problem. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Forms, Forms and More Forms. Book Seven. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Forms, Forms, and More Forms is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training…

Finding Your Way. Book Six. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Finding Your Way is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training program. The…

Buying a Car: Decisions, Decisions. Book Two. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Buying a Car: Decisions, Decisions is one of eight booklets designed for intermediate level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver…

Signs, Symbols and Signals. Book Five. Project Drive.

ERIC Educational Resources Information Center

Zook, Doris; And Others

This Project Drive booklet titled Signs, Symbols, and Signals is one of eight booklets designed for intermediate-level English-as-a-second-language students and low-level adult basic education/basic reading students. The goal of the booklet is to aid the student in developing the oral and sight vocabulary necessary for a basic driver training…

Examination of Cognitive and Instrumental Functional Performance as Indicators for Driving Cessation Risk across 3 Years

ERIC Educational Resources Information Center

Ackerman, Michelle L.; Edwards, Jerri D.; Ross, Lesley A.; Ball, Karlene K.; Lunsman, Melissa

2008-01-01

Purpose: The purpose of this study was to prospectively examine the role of cognitive and instrumental functional performance in driving cessation while simultaneously accounting for any contributions of demographics, vision, physical performance, and health among a sample of older adults without dementia. Design and Methods: Included in the…

40 CFR 86.129-94 - Road load power, test weight, inertia weight class determination, and fuel temperature profile.

Code of Federal Regulations, 2010 CFR

2010-07-01

... specified driving schedule. The design of the laboratory facility should include consideration of any parameters that may affect fuel temperatures, such as solar loading, pavement heat, and relative wind... be at least 125 °F throughout the driving period. Pavement temperature shall be measured and recorded...