7 CFR 1728.201 - Bulletin 1728H-701, Specification for Wood Crossarms (Solid and Laminated), Transmission Timbers...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 11 2013-01-01 2013-01-01 false Bulletin 1728H-701, Specification for Wood Crossarms (Solid and Laminated), Transmission Timbers and Pole Keys. 1728.201 Section 1728.201 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE...

Theoretical modeling and experimental analyses of laminated wood composite poles

Treesearch

Cheng Piao; Todd F. Shupe; Vijaya Gopu; Chung Y. Hse

2005-01-01

Wood laminated composite poles consist of trapezoid-shaped wood strips bonded with synthetic resin. The thick-walled hollow poles had adequate strength and stiffness properties and were a promising substitute for solid wood poles. It was necessary to develop theoretical models to facilitate the manufacture and future installation and maintenance of this novel...

AWPA biodeterioration hazard map revisited

Treesearch

Grant T. Kirker; Amy B. Bishell; William J. Hickey

2017-01-01

The fungal decay hazard map used by the American Wood Protection Association (AWPA) currently describes regional decay hazards in ground contact for North America and is based on condition assessments of utility poles from the 1970’s. Current work at the USDA Forest Service, Forest Products Laboratory is underway to analyze soil and wood samples from several National...

Effect of PF impregnation and surface densification on the mechanical properties of small-scale wood laminated poles

Treesearch

Huaqiang Yu; Chung Y. Hse; Zehui Jiang

2009-01-01

The wood poles in the United States are from high-valued trees that are becoming more expensive and less available. Wood laminated composite poles (LCP) are a kind of alternative to solid poles. Considerable interest has developed in last century in the resin impregnation and wood surface densification to improve its physical and mechanical properties. In this...

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

PubMed Central

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55–65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0–25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T. harzianum. It is concluded that carefully selected Trichoderma isolates can be used for integrated wood protection against a range of wood destroying basidiomycetes and may have potential for integrated wood protection in the field. PMID:28379978

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

PubMed

Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T. harzianum. It is concluded that carefully selected Trichoderma isolates can be used for integrated wood protection against a range of wood destroying basidiomycetes and may have potential for integrated wood protection in the field.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthony, R.W.; Bodig, J.; Phillips, G.E.

This report describes the development of a nondestructive evaluation (NDE) methodology for assessing the bending strength of new wood utility poles. Fundamental concepts of stress wave propagation are presented. The development of a longitudinal stress wave methodology for predicting pole strength and the results of destructive tests on full-size poles are described. Mathematical correlations between stress wave parameters, geometric characteristics, and individual pole bending strengths form the basis of strength prediction models for western redcedar, Douglas-fir and southern pine poles. Models were developed for NDE in the whitewood stage and after preservative treatment of poles. For each species the twomore » most commonly used preservative types were evaluated. Excellent correlations were obtained for western redcedar and Douglas-fir poles, but high moisture content in the southern pine poles resulted in lower prediction accuracies for this species. Verification of the developed mathematical models demonstrates that improvement in classifying poles into the ANSI 05.1 tip-load capacities is technically feasible. The development and field trial of the prototype equipment for strength grading of new poles is also described. Research results can be used to benefit utilities by enabling the supply of strength graded poles with a higher accuracy than previously possible.« less

Effect of Trichoderma-enriched organic charcoal in the integrated wood protection strategy

PubMed Central

Gandía, Mónica; Marcos, Jose F.; Bas, Maria del Carmen; Fink, Siegfried

2017-01-01

The gradual elimination of chromium from wood preservative formulations results in higher Cu leaching and increased susceptibility to wood decay fungi. Finding a sustainable strategy in wood protection has become of great interest among researchers. The objective of these in vitro studies was to demonstrate the effect of T-720-enriched organic charcoal (biochar) against five wood decay basidiomycetes isolated from strongly damaged poles. For this purpose, the antagonistic potential of Trichoderma harzianum (strain T-720) was confirmed among other four Trichoderma spp. against five brown-rot basidiomycetes in dual culture tests. T-720 was genetically transformed and tagged with the green fluorescent protein (GFP) in order to study its antagonistic mechanism against wood decay basidiomycetes. It was also demonstrated that T-720 inhibits the oxalic acid production by basidiomycetes, a well-known mechanism used by brown-rot fungi to detoxify Cu from impregnated wood. Additionally, this study evaluated the effect of biochar, alone or in combination with T-720, on Cu leaching by different preservatives, pH stabilization and prevention of wood decay caused by five basidiomycetes. Addition of biochar resulted in a significant Cu binding released from impregnated wood specimens. T-720-enriched biochar showed a significant reduction of wood decay caused by four basidiomycetes. The addition of T-720-enriched biochar to the soil into which utility poles are placed may improve the efficiency of Cr-free wood preservatives. PMID:28797118

Effect of Trichoderma-enriched organic charcoal in the integrated wood protection strategy.

PubMed

Ribera, Javier; Gandía, Mónica; Marcos, Jose F; Bas, Maria Del Carmen; Fink, Siegfried; Schwarze, Francis W M R

2017-01-01

The gradual elimination of chromium from wood preservative formulations results in higher Cu leaching and increased susceptibility to wood decay fungi. Finding a sustainable strategy in wood protection has become of great interest among researchers. The objective of these in vitro studies was to demonstrate the effect of T-720-enriched organic charcoal (biochar) against five wood decay basidiomycetes isolated from strongly damaged poles. For this purpose, the antagonistic potential of Trichoderma harzianum (strain T-720) was confirmed among other four Trichoderma spp. against five brown-rot basidiomycetes in dual culture tests. T-720 was genetically transformed and tagged with the green fluorescent protein (GFP) in order to study its antagonistic mechanism against wood decay basidiomycetes. It was also demonstrated that T-720 inhibits the oxalic acid production by basidiomycetes, a well-known mechanism used by brown-rot fungi to detoxify Cu from impregnated wood. Additionally, this study evaluated the effect of biochar, alone or in combination with T-720, on Cu leaching by different preservatives, pH stabilization and prevention of wood decay caused by five basidiomycetes. Addition of biochar resulted in a significant Cu binding released from impregnated wood specimens. T-720-enriched biochar showed a significant reduction of wood decay caused by four basidiomycetes. The addition of T-720-enriched biochar to the soil into which utility poles are placed may improve the efficiency of Cr-free wood preservatives.

Superfund Record of Decision (EPA Region 6): Lincoln Creosote Site, Bossier City, LA, November 26, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-10-01

The Lincoln Creosote Site (Site) is located in Bossier City, Louisiana, and consists of a 20-acre industrial area that includes the former location of a wood treatment plant. Wood products such as railroad ties and utility poles were pressure treated at the plant, using creosote, chromated copper-arsenate (CCA) and pentachlorophenol (PCP) as wood preservatives. The compounds used for wood treatment contained metals, a number of semi-volatile organic base-neutral extractable compounds such as polynuclear aromatic hydrocarbon (PAHs). EPA`s selected removal action called for excavation of residential soils containing concentrations of wood treatment product residuals.

KENNEDY SPACE CENTER, FLA. - A female Red-bellied Woodpecker clings to a utility pole where it has made a home on Merritt Island Wildlife Refuge. The most common type of woodpecker in the South, the "Zebraback" nests in the cavities of trees and consumes large quantities of wood-boring beetles, as well as other insect pests. More than 280 species of birds make their homes on the 140,000-acre refuge, which lies within the boundaries of Kennedy Space Center.

NASA Image and Video Library

1995-04-10

KENNEDY SPACE CENTER, FLA. - A female Red-bellied Woodpecker clings to a utility pole where it has made a home on Merritt Island Wildlife Refuge. The most common type of woodpecker in the South, the "Zebraback" nests in the cavities of trees and consumes large quantities of wood-boring beetles, as well as other insect pests. More than 280 species of birds make their homes on the 140,000-acre refuge, which lies within the boundaries of Kennedy Space Center.

Finite element modeling of small-scale tapered wood-laminated composite poles with biomimicry features

Treesearch

Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

2008-01-01

Tapered composite poles with biomimicry features as in bamboo are a new generation of wood laminated composite poles that may some day be considered as an alternative to solid wood poles that are widely used in the transmission and telecommunication fields. Five finite element models were developed with ANSYS to predict and assess the performance of five types of...

Taper of wood poles

Treesearch

Billy Bohannan; Hermann Habermann; Joan E. Lengel

1974-01-01

Round wood pole use has changed without accompanying advancement in engineering design data. Previous pole design was based on the assumption that maximum stress occurred at the groundline but, with the larger poles that are now being used, maximum stress may occur along the pole length. For accurate engineering analysis the shape or taper of a pole must be known. Both...

INVESTIGATION OF THE POTENTIAL RELEASE OF POLYCHLORINATED DIOXINS AND FURANS FROM PCP-TREATED UTILITY POLES

EPA Science Inventory

The United States (US) Environmental Protection Agency (EPA) estimated that the use of technical grade pentachlorophenol (PCP) between 1970 and 1995 to treat wood was approximately 400,000 metric tons in the US, and that between 4,800 and 36,000 grams of 2,3,7,8-tetrachlorodiben...

Finite element analyses of wood laminated composite poles

Treesearch

Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

2005-01-01

Finite element analyses using ANSYS were conducted on orthotropic, polygonal, wood laminated composite poles subjected to a body force and a concentrated load at the free end. Deflections and stress distributions of small-scale and full-size composite poles were analyzed and compared to the results obtained in an experimental study. The predicted deflection for both...

Factors affecting sodium hypochlorite extraction of CCA from treated wood.

PubMed

Gezer, E D; Cooper, P A

2009-12-01

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 degrees C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.

Structural fatigue test results for large wind turbine blade sections

NASA Technical Reports Server (NTRS)

Faddoul, J. R.; Sullivan, T. L.

1982-01-01

In order to provide quantitative information on the operating life capabilities of wind turbine rotor blade concepts for root-end load transfer, a series of cantilever beam fatigue tests was conducted. Fatigue tests were conducted on a laminated wood blade with bonded steel studs, a low cost steel spar (utility pole) with a welded flange, a utility pole with additional root-end thickness provided by a swaged collar, fiberglass spars with both bonded and nonbonded fittings, and, finally, an aluminum blade with a bolted steel fitting (Lockheed Mod-0 blade). Photographs, data, and conclusions for each of these tests are presented. In addition, the aluminum blade test results are compared to field failure information; these results provide evidence that the cantilever beam type of fatigue test is a satisfactory method for obtaining qualitative data on blade life expectancy and for identifying structurally underdesigned areas (hot spots).

Production and marketing of wood piling and poles in the Northeast

Treesearch

Myron D. Ostrander

1953-01-01

Since the earliest colonial settlements along the northeastern seaboard, wood piling has been used for wharves and piers and other waterfront structures. As waterside industries and waterborne commerce grew, the demand for wood piling grew.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.Y.; Valenti, J.C.; Tabor, D.G.

The use of waste wood as fuel for producing energy is a promising supplement to fossil fuels for many regions of the country. In addition to recovering energy and conserving landfill space, burning waste wood fuels also mitigates global warming created by fossil fuel combustion. However, the environmental consequences resulting from emissions generated by combustion of waste wood which contains paints, resins, or preservatives are not well understood. The combustion of waste wood treated with chemicals may produce potentially hazardous products of incomplete combustion (PIC) emissions such as dioxins. Characterization of PIC emissions from the combustion of waste wood previouslymore » treated with pentachlorophenol is reported in this study. Utility poles and crossbars are typically treated with a preservative such as pentachlorophenol in order to prolong their service life. They are disposed of by landfilling after being taken out of service. Burning such wood waste in boilers for steam generation becomes an increasingly attractive waste management alternative as it contains substantial energy value and reduces landfilling costs. Pilot-scale combustion tests were conducted under well controlled conditions in a 0.58 MW (2 million Btu/hr) combustor to compare PIC emissions from burning untreated wood and pentachlorophenol-treated wood. Sampling and analyses for a wide variety of PICs, including volatile organic compounds (VOCs), semivolatile organic compounds, and dioxins and furans, were performed to assess the effect of pentachlorophenol preservative present in wood on PIC emissions.« less

Nondestructive Evaluation of Young's Moduli of Full-Size wood Laminated Composite Poles

Treesearch

Cheng Piao; Todd F. Shube; Chung Y. Hse; R.C. Tang

2004-01-01

An exploratory study was conducted to evaluate the Young's moduli of wood laminated composite poles (LCP) by using a free transverse vibration method. Full-size LCP, 6.1 m long and 10.2 cm in diameter, were lab-fabricated with 9 and/or 12 southern yellow pine [SYP] strips of thickness, 1.9 cm, 2.9 cm and 3.8 cm. The frequency of free transverse vibration in a LCP...

BIOREMEDIATION FIELD INITIATIVE SITE PROFILE: ESCAMBIA WOOD PRESERVING SITE - BROOKHAVEN

EPA Science Inventory

The Escambia Wood Preserving Site—Brookhaven in Brookhaven, Mississippi, is a former wood preserving facility that used pentachlo- rophenol (PCP) and creosote to treat wooden poles. The site contains two pressure treatment cylinders, a wastewater treatment system, five bulk pr...

Combustion characteristics of lodge pole pine wood chips. Technical progress report No. 15, September 16, 1978-September 15, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Junge, D.C.

1979-09-01

Significant quantits of wood resiue fuels are presently being used in industrial steam generating facilities. Recent studies indicate that substantial additional quantities of wood residue fuels are available for energy generation in the form of steam and/or electricity. A limited data base on the combustion characteristics of wood residue fuels has resulted in the installation and operation of inefficient combustion systems for these fuels. This investigation of the combustion characteristics of wood residue fuels was undertaken to provide a data base which could be used to optimize the combustion of such fuels. Optimization of the combustion process in industrial boilersmore » serves to improve combustion efficiency and to reduce air pollutant emissions generated in the combustion process. This report presents data on the combustion characteristics of lodge pole pine wood chips. The data were obtained in a pilot scale combustion test facility at Oregon State University.« less

Detail of 25' highband reflector screen pole showing the horizontal ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail of 25' high-band reflector screen pole showing the horizontal wood beams and vertical wires hung from ceramic insulators, note the dipole antenna element and 94' low-band reflector screen poles in background, view facing north - U.S. Naval Base, Pearl Harbor, Naval Radio Station, AF/FRD-10 Circularly Disposed Antenna Array, Wahiawa, Honolulu County, HI

Biodegradability of pentachlorophenol in the environment: A literature review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakles, D.

1993-04-01

Pentachlorophenol has been widely used as a wood preserving agent for over 50 years to treat millions of electrical utility poles and crossarms. Treatment of poles with pentachlorophenol has in some cases resulted in contamination of soils, groundwater, and surface water. Environmental releases are a concern because of the potential toxicity of pentachlorophenol and its stringent regulation. Microbiological degradation of pentachlorophenol in environmental media has been demonstrated in numerous cases. The potential for pentachlorophenol to be biologically degraded is of interest to the electrical utility industry for two reasons. First, it is a factor in understanding the probable fate ofmore » pentachlorophenol where it has been released into the environment, and second, its biodegradability can potentially result in effective and economical treatment strategies for soils, water, and subsurface environments. The objective of this literature review is to collect a baseline of information on the biodegradability of pentachlorophenol in soils, surface water, and groundwater for the electric utility industry. The focus of the electric utility industry's interest in the environmental management and control of pentachlorophenol is primarily in the management of environmental media, particularly soils, that may have become incidentally contaminated with pentachlorophenol in association with the treatment, storage, or use of utility poles and crossarms. The review of the literature has found that [open quotes]unassisted[close quotes] biodegradation of pentachlorophenol in aquatic, soil, and subsurface environments may occur, presumably if there is an acclimated microbial population of sufficient density. Aerobic conditions appear to be most conducive to biodegradation in these cases. Several studies have shown that with an acclimated, mixed culture and conventional wastewater treatment approaches, pentachlorophenol can be effectively treated in water.« less

Biodegradability of pentachlorophenol in the environment: A literature review. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakles, D.

1993-04-01

Pentachlorophenol has been widely used as a wood preserving agent for over 50 years to treat millions of electrical utility poles and crossarms. Treatment of poles with pentachlorophenol has in some cases resulted in contamination of soils, groundwater, and surface water. Environmental releases are a concern because of the potential toxicity of pentachlorophenol and its stringent regulation. Microbiological degradation of pentachlorophenol in environmental media has been demonstrated in numerous cases. The potential for pentachlorophenol to be biologically degraded is of interest to the electrical utility industry for two reasons. First, it is a factor in understanding the probable fate ofmore » pentachlorophenol where it has been released into the environment, and second, its biodegradability can potentially result in effective and economical treatment strategies for soils, water, and subsurface environments. The objective of this literature review is to collect a baseline of information on the biodegradability of pentachlorophenol in soils, surface water, and groundwater for the electric utility industry. The focus of the electric utility industry`s interest in the environmental management and control of pentachlorophenol is primarily in the management of environmental media, particularly soils, that may have become incidentally contaminated with pentachlorophenol in association with the treatment, storage, or use of utility poles and crossarms. The review of the literature has found that {open_quotes}unassisted{close_quotes} biodegradation of pentachlorophenol in aquatic, soil, and subsurface environments may occur, presumably if there is an acclimated microbial population of sufficient density. Aerobic conditions appear to be most conducive to biodegradation in these cases. Several studies have shown that with an acclimated, mixed culture and conventional wastewater treatment approaches, pentachlorophenol can be effectively treated in water.« less

Calculating broad neutron resonances in a cut-off Woods-Saxon potential

NASA Astrophysics Data System (ADS)

Baran, Á.; Noszály, Cs.; Salamon, P.; Vertse, T.

2015-07-01

In a cut-off Woods-Saxon (CWS) potential with realistic depth S -matrix poles being far from the imaginary wave number axis form a sequence where the distances of the consecutive resonances are inversely proportional with the cut-off radius value, which is an unphysical parameter. Other poles lying closer to the imaginary wave number axis might have trajectories with irregular shapes as the depth of the potential increases. Poles being close repel each other, and their repulsion is responsible for the changes of the directions of the corresponding trajectories. The repulsion might cause that certain resonances become antibound and later resonances again when they collide on the imaginary axis. The interaction is extremely sensitive to the cut-off radius value, which is an apparent handicap of the CWS potential.

Wood properties of immature ponderosa pine after thinning

Treesearch

Donald C. Markstrom; Harry E. Troxell; C. E. Boldt

1983-01-01

Trees from growing stock levels of 20, 60, and 100 in sapling and pole stands were sampled at three vertical positions -zero, 25, and 50 percent of total height above the 1-foot stump. Wood grown during the 10-year period after initial thinning was compared for growth and wood properties. Wide differences in radial growth, induced by thinning treatments, were not...

Removal of creosote from wood particles at different horizontal and vertical locations of decommissioned poles using steam treatment

Treesearch

Todd F. Shupe; Chung Y. Hse; Han Roliadi

2006-01-01

This study used steam treatment to evaluate the potential of this method to remove residual creosote content of sawdust from weathered, out-of-service poles. Steaming was successful in reducing the creosote content to a level of 1.31%, regardless of creosote content at the start of the steaming treatment. Poles with higher initial creosote contents required longer...

1. West elevations of barrier (Building 4216/E17) and Monitor Building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. West elevations of barrier (Building 4216/E-17) and Monitor Building (4203/E-4). Barrier is built of wood infilled with earth, intended to protect Monitor Building from flying debris should anything at Test Stand 'A' explode. Building 4203/E-4 is built of reinforced concrete; equipment on top of it is cooling tower for refrigeration equipment in Test Stand 'A' machinery room. Electrical utility poles are typical at the facility, and carry 4,800 volts 3-phase alternating current. - Jet Propulsion Laboratory Edwards Facility, Test Stand A, Control Center, Edwards Air Force Base, Boron, Kern County, CA

Bald eagles view their territory atop a utility pole at KSC

NASA Technical Reports Server (NTRS)

2000-01-01

This pair of bald eagles appear unhappy as the focus of the camera while they perch together on the top of a utility pole at Kennedy Space Center. The Center counts more than half a dozen bald eagles among the denizens of its site, especially since KSC shares a boundary with the Merritt Island National Wildlife Refuge. The Southern bald eagle is no stranger to Florida as it ranges throughout the state and along the coasts of California, Texas, Louisiana and south Atlantic states. Most southern Florida eagles nesting at KSC arrive during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

KSC-2009-2490

NASA Image and Video Library

2009-04-01

CAPE CANAVERAL, Fla. – Black vultures gather near woods in NASA's Kennedy Space Center in Florida. They are accompanied by a young white ibis. Ranging across the south and southeast, black vultures scavenge for both carrion and weak, sick or unprotected prey. They differ from turkey vultures in that they depend on vision to find food. They can be found all around Kennedy, on the ground or any higher landing spot, from buildings to utility poles. The center shares a boundary with the Merritt Island Wildlife Nature Refuge, which is a habitat for more than 310 species of birds, 25 mammals, 117 fishes and 65 amphibians and reptiles. Photo credit: NASA/Ben Smegelsky

Big George to Carter Mountain 115-kV transmission line project, Park and Hot Springs Counties, Wyoming. Environmental Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-01

The Western Area Power Administration (Western) is proposing to rebuild, operate, and maintain a 115-kilovolt (kV) transmission line between the Big George and Carter Mountain Substations in northwest Wyoming (Park and Hot Springs Counties). This environmental assessment (EA) was prepared in compliance with the National Environmental Policy Act (NEPA) and the regulations of the Council on Environmental Quality (CEQ) and the Department of Energy (DOE). The existing Big George to Carter Mountain 69-kV transmission line was constructed in 1941 by the US Department of Interior, Bureau of Reclamation, with 1/0 copper conductor on wood-pole H-frame structures without an overhead groundmore » wire. The line should be replaced because of the deteriorated condition of the wood-pole H-frame structures. Because the line lacks an overhead ground wire, it is subject to numerous outages caused by lightning. The line will be 54 years old in 1995, which is the target date for line replacement. The normal service life of a wood-pole line is 45 years. Under the No Action Alternative, no new transmission lines would be built in the project area. The existing 69-kV transmission line would continue to operate with routine maintenance, with no provisions made for replacement.« less

Silvical characteristics of Atlantic white-cedar (Chamaecyparis thyoides)

Treesearch

S. Little

1959-01-01

Atlantic white-cedar ((Chamaecyparis thyoides (L.) B.S.P.) has been a highly prized species since Colonial times because of the durability and high quality of its wood. The wood has been used for many purposes: boat boards, shingles and lath, framing, house and boat finish, pails and tanks, cabin logs, posts, and poles. Good white-cedar has always...

Diagnostics of Wooden Poles Situated in the Open - Air Museum Using Sonic Tomography

NASA Astrophysics Data System (ADS)

Makýš, Oto; Krušinský, Peter; Korenková, Renáta; Šrobárová, Dominika

2018-06-01

The paper deals with the lifetime of wooden poles, situated in the archaeological open-air museum Liptovská Mara - Havránok, which were erected outdoors about 12 years ago. It is aimed at diagnosing their condition using sonic tomography. The poles differ from each other in the location, anchorage, and positioning in terms of the terrain slope. Investigation was focused on the free-standing poles (quasi sacrifice poles) and the poles that are part of the fortification (gates and walls). Measurements were carried out using the device Fakopp ArborSonic 3D Sonic Tomograph that has 18 sensors. It measures the sonic response (sound velocity) in a tree stem. Sound wave velocity within sound wood depends on its species, moisture content, and the direction of measurement. Measurements brought remarkable results.

Enhanced migration of polychlorodibenzo-p-dioxins and furans in the presence of pentachlorophenol-treated oil in soil around utility poles: screening model validation.

PubMed

Bulle, Cécile; Samson, Réjean; Deschênes, Louise

2010-03-01

Field samples were collected around six pentachlorophenol (PCP)-treated wooden poles (in clay, organic soil, and sand) to evaluate the vertical migration of polychlorodibenzo-p-dioxins and furans (PCDD/Fs). Soils were characterized, PCDD/Fs, C(10)-C(50), and PCP were analyzed for seven composite samples located at a depth from 0 to 100 cm and at a distance from 0 to 50 cm from each pole. Concentrations of PCDD/Fs measured in organic soils were the highest (maximum 1.2E + 05 pg toxic equivalent TEQ/g soil), followed by clay (maximum 3.8E + 04 pg TEQ/g soil) and sand (maximum 1.8E + 04 pg TEQ/g soil). Model predictions, including the influence of wood treatment oil, were validated using measured concentration values in soils around poles. The model predicts a migration of PCDD/Fs due to the migration of oil, which differs depending on the type of soil: in clay, 90% of PCDD/Fs are predicted to remain in the first 29 cm, whereas in sand, 80 to 90% of the emitted PCDD/Fs are predicted to migrate deeper than 185 cm. For the organic soil, the predicted migration depth varies from 90 to 155 cm. This screening model allows evaluating the danger of microcontaminated sites around PCP-treated wooden poles: from a risk assessment perspective, in the case of organic soil and clay, no PCDD/F contamination is to be expected below the pole, but high levels of PCDD/Fs can be found in the first 2 m below the surface. For sand, however, significantly lower levels of PCDD/Fs were predicted in the surface soil, while the migration depth remains elevated, posing an inherent danger of aquifer contamination under the pole.

Economics of Red Pine Management for Utility Pole Timber

Treesearch

Gerald H. Grossman; Karen Potter-Witter

1991-01-01

Including utility poles in red pine management regimes leads to distinctly different management recommendations. Where utility pole markets exist, managing for poles will maximize net returns. To do so, plantations should be maintained above 110 ft2/ac, higher than usually recommended. In Michigan's northern lower peninsula, approximately...

DOE Office of Scientific and Technical Information (OSTI.GOV)

L. John Fahy; Lyle A. Johnson, Jr.

Beginning in 1990, efforts were initiated for Western Research Institute (WRI) to implement an in situ remediation project for the contaminated aquifer at the Bell Lumber and Pole Company (Bell Pole) Site in New Brighton, Minnesota. The remediation project involves the application of the Contained Recovery of Oily Waste (CROW{trademark}) process, which consists of hot-water injection to displace and recover the non-aqueous phase liquids (NAPL) (Johnson and Sudduth 1989). Wood treating activities began at the Bell Pole Site in 1923 and have included the use of creosote and pentachlorophenol (PCP) in a fuel oil carrier. Creosote was used as amore » wood preservative from 1923 to 1958. Provalene 4-A, a non-sludging fuel-oil-type carrier for PCP, was used from 1952 until it was no longer commercially available in 1968. A 5-6% mixture of PCP in fuel oil has been used as a wood preservative since 1952, and a fuel-oil-type carrier, P-9, has been used since 1968. While reviewing the site evaluation information, it became apparent that better site characterization would enhance the outcome of the project. Additional coring indicated that the area's extent of the contaminated soils was approximately eight times greater than initially believed. Because of these uncertainties, a pilot test was conducted, which provided containment and organic recovery information that assisted in the design of the full-scale CROW process demonstration.« less

Utility pole crash modeling.

DOT National Transportation Integrated Search

2001-02-01

Maine was recently ranked 9th in the nation concerning fatalities caused by collisions with utility poles based on : Miles of Travel. The number of collisions and fatalities can be reduced significantly with an updated Utility Pole : Placement Policy...

7 CFR 1728.201 - RUS Bulletin 1728H-701, RUS Specification for Wood Crossarms (Solid and Laminated), Transmission...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., Standard Method for Analysis of Treated Wood and Treating Solutions by X-Ray Spectroscopy. (viii) A11-83...) C1-91, All Timber Products—Preservative Treatment by Pressure Processes. (x) C4-91, Poles... spaced. (x) Knots which have a maximum of 5/8 inch (1.59 cm) diameter may intersect pin holes in the...

7 CFR 1728.201 - RUS Bulletin 1728H-701, RUS Specification for Wood Crossarms (Solid and Laminated), Transmission...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., Standard Method for Analysis of Treated Wood and Treating Solutions by X-Ray Spectroscopy. (viii) A11-83...) C1-91, All Timber Products—Preservative Treatment by Pressure Processes. (x) C4-91, Poles... spaced. (x) Knots which have a maximum of 5/8 inch (1.59 cm) diameter may intersect pin holes in the...

Poles of the S-matrix in Woods-Saxon and Salamon-Vertse potentials

NASA Astrophysics Data System (ADS)

Vertse, T.; Lovas, R. G.; Salamon, P.; Rácz, A.

2012-10-01

The motions of the l = 0 poles of the S-matrix with varying potential strength is calculated in a cut-off Woods-Saxon (CWS) potential and in the Salamon-Vertse (SV) potential [3]. Both potentials are zero beyond a certain finite distance but the CWS potential has a jump at the cut while the SV potential goes to zero smoothly. The jump of the CWS potential might cause a strange circling of the trajectories at their starting region. This feature does not appear with the SV potential. Starting points of the trajectories depend on the ranges of the potentials. For CWS these points do depend on the unphysical cut-off radius. In this respect the SV potential seems to be superior to the CWS potential.

Fiber grating system used to measure strain in a 22-ft composite utility pole

NASA Astrophysics Data System (ADS)

Udd, Eric; Corona, Kelli; Slattery, Kerry T.; Dorr, Donald J.

1996-05-01

Composite utility poles have significant advantages with respect to wooden utility poles that include superior strength and uniformity, light weight for ease of deployment, the ability to be recycled reducing hazardous waste associated with chemically treated wooden poles, and compatibility with embedded fiber optic sensors allowing structural loads to be monitored. This paper reports tests conducted of fiber optic grating sensors in combination with an overcoupled coupler demodulation system to support structural testing of a 22 foot composite pole.

Sequential electrokinetic treatment and oxalic acid extraction for the removal of Cu, Cr and As from wood.

PubMed

Isosaari, Pirjo; Marjavaara, Pieti; Lehmus, Eila

2010-10-15

Removal of Cu, Cr and As from utility poles treated with chromated copper arsenate (CCA) was investigated using different one- to three-step combinations of oxalic acid extraction and electrokinetic treatment. The experiments were carried out at room temperature, using 0.8% oxalic acid and 30 V (200 V/m) of direct current (DC) or alternating current in combination (DC/AC). Six-hour extraction removed only 15%, 11% and 28% and 7-day electrokinetic treatment 57%, 0% and 17% of Cu, Cr and As from wood chips, respectively. The best combination for all the metals was a three-step process consisting of pre-extraction, electrokinetics and post-extraction steps, yielding removals of 67% for Cu, 64% for Cr and 81% for As. Oxalic acid extraction prior to electrokinetic treatment was deleterious to further removal of Cu, but it was necessary for Cr and As removal. Chemical equilibrium modelling was used to explain the differences in the behaviour of Cu, Cr and As. Due to the dissimilar nature of these metals, it appeared that even more process sequences and/or stricter control of the process conditions would be needed to obtain the >99% removals required for safe recycling of the purified wood material. 2010 Elsevier B.V. All rights reserved.

Wood products used in constructing conservation and development projects by the Corps of Engineers in the United States, 1962 and 1978

Treesearch

W. H. Reid; D. B. McKeever

Estimates of the amounts of wood products used in constructing civil conservation and development projects by the Corps of Engineers in the United States are presented for the years 1962 and 1978. Amounts of lumber, laminated lumber, poles and piling, and plywood used in construction are stratified by five construction categories, and three types of uses. Estimates of...

32 CFR 644.504 - Disposal plan for timber.

Code of Federal Regulations, 2010 CFR

2010-07-01

... disposal plan will be prepared which will include the following: (a) Live timber and merchantable dead... feet in log scale measurement; linear estimates of pole timber, and amount of cord wood. The appraiser...

Climate Change Mitigation Challenge for Wood Utilization-The Case of Finland.

PubMed

Soimakallio, Sampo; Saikku, Laura; Valsta, Lauri; Pingoud, Kim

2016-05-17

The urgent need to mitigate climate change invokes both opportunities and challenges for forest biomass utilization. Fossil fuels can be substituted by using wood products in place of alternative materials and energy, but wood harvesting reduces forest carbon sink and processing of wood products requires material and energy inputs. We assessed the extended life cycle carbon emissions considering substitution impacts for various wood utilization scenarios over 100 years from 2010 onward for Finland. The scenarios were based on various but constant wood utilization structures reflecting current and anticipated mix of wood utilization activities. We applied stochastic simulation to deal with the uncertainty in a number of input variables required. According to our analysis, the wood utilization decrease net carbon emissions with a probability lower than 40% for each of the studied scenarios. Furthermore, large emission reductions were exceptionally unlikely. The uncertainty of the results were influenced clearly the most by the reduction in the forest carbon sink. There is a significant trade-off between avoiding emissions through fossil fuel substitution and reduction in forest carbon sink due to wood harvesting. This creates a major challenge for forest management practices and wood utilization activities in responding to ambitious climate change mitigation targets.

Tension and compression measurements in composite utility poles using fiber optic grating sensors

NASA Astrophysics Data System (ADS)

Udd, Eric; Corona-Bittick, Kelli; Slattery, Kerry T.; Dorr, Donald J.

1995-04-01

Composite utility poles have the potential to overcome many of the limitations of wooden poles that are currently widely used. Significant advantages include superior strength and uniformity, light weight for ease of deployment, the ability to be recycled reducing hazardous waste associated with chemically treated wooden poles, and compatibility with embedded fiber optic sensors allowing structural loads to be monitored. This paper describes the usage of fiber optic grating sensors to support structural testing of a 22 foot composite pole.

Owl Nest behind TV Building

NASA Image and Video Library

2014-03-18

CAPE CANAVERAL, Fla. – At NASA's Kennedy Space Center in Florida, an Owl occupies a nest originally build by an Osprey atop a loudspeaker utility pole. Kennedy Space Center shares a boundary with the Merritt Island National Wildlife Refuge. The Refuge encompasses 140,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects. For more information, visit: http://www.nasa.gov/centers/kennedy/shuttleoperations/alligators/kscovr.html Photo credit: NASA/Dimitri Gerondidakis

Repair of impact damaged utility poles with fiber reinforced polymers (FRP), phase II : [summary].

DOT National Transportation Integrated Search

2015-04-01

The aluminum and steel utility poles which support traffic signals, lighting, or mast-arm signs : are vulnerable to collisions from vehicles because of proximity to roadways. Removing these : poles for repair is costly and time-consuming, and removal...

Quantities of Arsenic-Treated Wood in Demolition Debris Generated by Hurricane Katrina

PubMed Central

Dubey, Brajesh; Solo-Gabriele, Helena M.; Townsend, Timothy G.

2008-01-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood. PMID:17396637

A pair of bald eagles on a utility pole at KSC.

NASA Technical Reports Server (NTRS)

2000-01-01

A pair of nesting bald eagles share a utility pole on Kennedy Parkway North. Nearby is their 11-foot-deep nest, in a pine tree, which has been home to one or more pairs of eagles for two dozen years. It is one of a dozen eagle nests in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nests in Florida Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

Serum profiles of PCDDs and PCDFs, in individuals near the Escambia Wood Treating Company Superfund site in Pensacola, FL.

PubMed

Karouna-Renier, Natalie K; Rao, K Ranga; Lanza, John J; Davis, Deeya A; Wilson, Patricia A

2007-10-01

The Escambia Wood Treating Company (ETC) Superfund site, Pensacola, FL, is contaminated with polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F), benzo(a)pyrene, lead and arsenic from pentachlorophenol (PCP), creosote, and other compounds used to treat utility poles and foundation pilings. Although ETC's operations ceased in 1982, soils in the areas surrounding the facility continue to exhibit elevated levels of contaminants attributable to ETC operations. In July 2000, individuals who may have been affected by contamination from the ETC site, including current and former residents and former workers and their household members were invited to participate in a study, which included a health and exposure history and routine blood analysis. We also conducted a toxicological health evaluation of a subset of these eligible workers/residents by analyzing serum levels of 17 PCDD/F congeners. Members of the ETC cohort exhibited elevated serum PCDD/F relative to the general population, and congener profiles in members of the cohort reflected patterns commonly observed in persons exposed to PCP. Hypertension prevalence in the cohort was found to correlate with PCDD/F levels, although no other significant relationships were identified with monitored health indices.

Gluability of out-of-service utility poles

Treesearch

Han Roliadi; Chung Y. Hse; Elvin T. Choong; Todd F. Shupe

2000-01-01

This investigation determined the gluability of weathered, out-of-service southern yellow pine (SYP) (Pinus spp.) utility poles. Three types of adhesives were used: resorcinol-phenol formaldehyde (RPF), polyvinyl acetate (PVA), and casein. The poles consisted of two service duration groups: 5 and 25 years. Longer weathering caused greater reduction in creosote content...

Compositional Analysis of Fine Particulate Matter in Fairbanks, Alaska

NASA Astrophysics Data System (ADS)

Nattinger, K.; Simpson, W. R.; Huff, D.

2015-12-01

Fairbanks, AK experiences extreme pollution episodes that result in winter violations of the fine particulate matter (PM2.5) National Ambient Air Quality Standards. This poses a significant health risk for the inhabitants of the area. These high levels result from trapping of pollution in a very shallow boundary layer due to local meteorology, but the role of primary (direct emission) of particulate matter versus secondary production (in the atmosphere) of particulate matter is not understood. Analysis of the PM2.5 composition is being conducted to provide insight into sources, trends, and chemistry. Methods are developed to convert carbon data from IMPROVE (post-2009 analysis method) to NIOSH (pre-2009 method) utilizing blank subtraction, sampler bias adjustment, and inter-method correlations from co-located samples. By converting all carbon measurements to a consistent basis, long-term trends can be analyzed. The approach shows excellent mass closure between PM2.5 mass reconstructed from constituents and gravimetric-analyzed mass. This approach could be utilized in other US locations where the carbon analysis methods also changed. Results include organic and inorganic fractional mass percentages, analyzed over an eight-year period for two testing sites in Fairbanks and two in the nearby city of North Pole. We focus on the wintertime (Nov—Feb) period when most air quality violations occur and find that the particles consist primarily of organic carbon, with smaller percentages of sulfate, elemental carbon, ammonium, and nitrate. The Fairbanks area PM2.5 organic carbon / elemental carbon partitioning matches the source profile of wood smoke. North Pole and Fairbanks PM2.5 have significant compositional differences, with North Pole having a larger percentage of organic matter. Mass loadings in SO42-, NO3-, and total PM2.5 mass correlate with temperature. Multi-year temporal trends show little if any change with a strong effect from temperature. Insights from this study regarding primary versus possible secondary PM2.5 production processes can help in identifying effective PM2.5 control strategies.

Contemporary wood utilization research needs in the Western United States.

Treesearch

Robert A. Monserud; Eini C. Lowell; Dennis R. Becker; Susan Stevens Hummel; Ellen M. Donoghue; R. James Barbour; Kenneth A. Kilborn; David L. Nicholls; Joe Roos; Randall A. Cantrell

2004-01-01

Contemporary wood utilization research needs in the Western United States are examined in this problem analysis. Key focal areas include: A. Changes in forest management actions and policies affect forest conditions and people, which in turn affect wood quality and wood utilization opportunities. B. Effects of natural disturbances (e.g., wildfire, insect outbreaks) on...

‘Fire hardening’ spear wood does slightly harden it, but makes it much weaker and more brittle

PubMed Central

Chan, Tak Lok

2016-01-01

It is usually assumed that ‘fire hardening’ the tips of spears, as practised by hunter–gatherers and early Homo spp., makes them harder and better suited for hunting. This suggestion was tested by subjecting coppiced poles of hazel to a fire-hardening process and comparing their mechanical properties to those of naturally seasoned poles. A Shore D hardness test showed that fire treatment slightly increased the hardness of the wood, but flexural and impact tests showed that it reduced the strength and work of fracture by 30% and 36%, respectively. These results suggest that though potentially slightly sharper and more durable, fire-hardened tips would actually be more likely to break off when used, as may have been the case with the earliest known wooden tool, the Clacton spear. Fire might first have been used to help sharpen the tips of spears, and fire-hardening would have been a mostly negative side effect, not its primary purpose. PMID:27194289

A hawk is ready for flight

NASA Technical Reports Server (NTRS)

2000-01-01

This Broad-Winged Hawk is ready for flight from its perch on a utility pole at Kennedy Space Center. This hawk's habitat is chiefly deciduous woodland, ranging from southern Canada south throughout the eastern United States, including a small area of Central Florida. It winters in tropical South America. The Center shares a boundary with the Merritt Island National Wildlife Refuge, a haven and habitat for more than 331 species of birds. The Refuge encompasses 92,000 acres that are also a habitat for 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

Electric utility pole yard training facility: Designing an effective learning environment

NASA Astrophysics Data System (ADS)

Topping, Robert P.

The primary responsibility of electric utilities is to supply consistent, dependable, and affordable energy to private customers, businesses, and industries. As with many businesses, electric utilities are experiencing the effects of an aging workforce and expending considerable resources to train their current and replacement workers. Community colleges can partner with electric utilities to provide effective learning environments for these workers, and gain access to new sources of revenue and community support for the colleges. The purpose of this study was to describe the functions, features, and major design issues of an effective learning environment for training electric utility industry workers, the electric utility line-worker pole yard. Case studies of three "state of the art" line-worker pole yard training environments provide the basis for the study's findings and implications. The study was guided by the following research questions: (1) What is the function of a line-worker pole yard in supporting effective training? (2) What are the features of present day ("state of the art") line-worker pole yard learning environments? and (3) What are the major issues that need to be addressed in designing a line-worker pole yard learning environment for the future? The study participants included industry representatives, training coordinators, instructors, and students from the three selected "state of the art" line-worker pole yard sites. The overall findings from the study resulted in composites of the desired features of learning outcomes, learning process, and learning environment for a line-worker pole yard training program and major issues that are affecting the future design of these training programs. Composite findings of a pole-yard training environment included unique features associated with: (a) outdoor, (b) indoor, (c) underground, (d) classroom, (e) gathering places, and (f) work-based learning components. Composite findings with regard to major issues that need to be considered in future designs of pole-yard training environments included: (a) available unrestricted land for expansion, (b) resource commitment level, (c) workforce demographics, (d) aging industrial infrastructure, (e) electronic information and communication capability, (f) quality and quantity of available instructors, and (g) environmental and economic impact.

A Southern Bald Eagle perches on a pole at KSC.

NASA Technical Reports Server (NTRS)

2000-01-01

A Southern Bald Eagle perched on top of a utility pole searches the area. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

A Southern Bald Eagle perches on a pole at KSC.

NASA Technical Reports Server (NTRS)

2000-01-01

A Southern Bald Eagle perches on top of a utility pole at Kennedy Space Center. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

Developing clones of Eucalyptus cloeziana resistant to rust (Puccinia psidii)

Treesearch

Rafael F. Alfenas; Marcelo M. Coutinho; Camila S. Freitas; Rodrigo G. Freitas; Acelino C. Alfenas

2012-01-01

Besides its high resistance to Chrysoporthe cubensis canker, Eucalyptus cloeziana F. Muell. is a highly valuable tree species for wood production. It can be used for furniture, electric poles, fence posts, and charcoal. Nevertheless, it is highly susceptible to the rust caused by Puccinia psidii, which...

LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

PubMed

Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

2015-04-01

Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fiber grating systems used to measure strain in cylindrical structures

NASA Astrophysics Data System (ADS)

Udd, Eric; Corona-Bittick, Kelli; Slattery, Kerry T.; Dorr, Donald J.; Crowe, C. Robert; Vandiver, Terry L.; Evans, Robert N.

1997-07-01

Fiber optic grating systems are described that have been used to measure strain in cylindrical structures. The applications of these systems to a composite utility pole and to a composite missile body are described. Composite utility poles have significant advantages with respect to wooden utility poles that include superior strength and uniformity; light weight for ease of deployment; the ability to be recycled, reducing hazardous waste associated with chemically treated wooden poles; and compatibility with embedded fiber optic sensors, allowing structural loads to be monitored. Tests conducted of fiber optic grating sensors in combination with an overcoupled coupler demodulation system to support structural testing of a 22-ft composite pole are reported. Monitoring strain in composite missile bodies has the potential to improve the quality of manufactured parts, support performance testing, and enhance safety during long periods of storage. Strain measurements made with fiber optic grating and electrical strain gauges are described.

Decay resistance of out-of-service utility poles as related to the distribution of residual creosote content

Treesearch

Han Roliadi; Chung Y. Hse; Elvin T. Choong; Todd F. Shupe

2000-01-01

Decay resistance of out-of-service poles was investigated to evaluate their effectiveness against biodegradation for possible recycling of these poles for composite products. Decay resistance was related to creosote content and creosote distribution in poles with service durations of 5 and 25 years and also freshly treated poles. Weathering of the poles had caused...

47 CFR 1.1402 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... controlled by a utility. (c) With respect to poles, the term usable space means the space on a utility pole... equipment, and which includes space occupied by the utility. With respect to conduit, the term usable space... together with their supporting infrastructure. (k) The term duct means a single enclosed raceway for...

47 CFR 1.1402 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... controlled by a utility. (c) With respect to poles, the term usable space means the space on a utility pole... equipment, and which includes space occupied by the utility. With respect to conduit, the term usable space... together with their supporting infrastructure. (k) The term duct means a single enclosed raceway for...

47 CFR 1.1402 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... controlled by a utility. (c) With respect to poles, the term usable space means the space on a utility pole... equipment, and which includes space occupied by the utility. With respect to conduit, the term usable space... together with their supporting infrastructure. (k) The term duct means a single enclosed raceway for...

Opportunities to change timber demand through altered timber utilization [Chapter 10

Treesearch

K. E. Skog; D. P. Bradley; H. N. Spelter; I. Durbak; P. J. Ince; W. J. Lange; P. A. Araman; D. B. McKeever; J. I. Zerbe

1990-01-01

This paper discusses opportunities for timber utilization improvement that will 1) increase efficiency of wood use, 2) reduce the cost of wood products and the cost of using wood in applications, and 3) provide new or improved wood products or wood use applications. A key purpose here is to propose and explain technology-influenced projections of 1) costs for...

A red-tailed hawk at KSC

NASA Technical Reports Server (NTRS)

2000-01-01

From the top of a utility pole, a red-tailed hawk launches into flight, perhaps after spotting prey, typically a small rodent. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

77 FR 67270 - Revising the Exemption for Digger Derricks in the Cranes and Derricks in Construction Standard

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-09

... also involved placing a pole in the hole and attaching transformers and other items to the pole... industries, including placing utility poles in the ground and attaching transformers and other equipment to...- mount transformers on the ground as part of the same power system as the poles. While the pole work is...

Wood-plastic composites utilizing wood flours derived from fast- growing trees common to the midwest

USDA-ARS?s Scientific Manuscript database

There are several non- or under-utilized hardwood trees common to the Midwestern states. Wood flour (WF) derived from fast-growing Midwest trees (Osage orange, Black Locust and Red Mulberry) were evaluated as a source of bio-based fiber reinforcements. Wood plastic composites (WPC) of high density p...

76 FR 37105 - Pacific Gas and Electric Company; Notice of Application Accepted for Filing, Soliciting Motions...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

.... Name of Project: Rollins Transmission Line Project. f. Location: The Rollins Transmission Line Project...: Mary Greene, (202) 502-8865 or [email protected] . j. Deadline for filing motions to intervene and..., three-phase, 60-kilovolt (kV), wood-pole transmission line extending from the existing Rollins...

Proposed Columbia Wind Farm No. 1 : Final Environmental Impact Statement, Joint NEPA/SEPA.

DOE Office of Scientific and Technical Information (OSTI.GOV)

United States. Bonneville Power Administration; Klickitat County

1995-09-01

CARES proposes to construct and operate the 25 megawatt Columbia Wind Farm No. 1 (Project) in the Columbia Hills area of Klickitat County, Washington known as Juniper Point. Wind is not a constant resource and based on the site wind measurement data, it is estimated that the Project would generate approximately 7 average annual MWs of electricity. BPA proposes to purchase the electricity generated by the Project. CARES would execute a contractual agreement with a wind developer, to install approximately 91 wind turbines and associated facilities to generate electricity. The Project`s construction and operation would include: install concrete pier foundationsmore » for each wind turbine; install 91 model AWT-26 wind turbines using 43 m high guyed tubular towers on the pier foundations; construct a new 115/24-kv substation; construct a 149 m{sup 2} steel operations and maintenance building; install 25 pad mount transformers along the turbine access roads; install 4.0 km of underground 24 kv power collection lines to collect power from individual turbines to the end of turbine strings; install 1.2 km of underground communication and transmission lines from each turbine to a pad mount transformer; install 5.6 km of 24 kv wood pole transmission lines to deliver electricity from the pad mount transformers to the Project substation; install 3.2 km of 115 kv wood pole transmission lines to deliver electricity from the Project substation to the Public Utility District No. 1 of Klickitat County(PUD)115 kv Goldendale line; interconnect with the BPA transmission system through the Goldendale line and Goldendale substation owned by the PUD; reconstruct, upgrade, and maintain 8.0 km of existing roads; construct and maintain 6.4 km of new graveled roads along the turbine strings and to individual turbines; and install meteorological towers guyed with rebar anchors on the Project site.« less

40 CFR 761.123 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., floors, roofs, roadways and sidewalks in the industrial area, utility poles, unmanned machinery, concrete... areas above 6 feet in height, roofs, asphalt roadways, concrete roadways, wooden utility poles, unmanned..., metals, glass, aluminum siding, and enameled or laminated surfaces. Low-concentration PCBs means PCBs...

40 CFR 761.123 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., floors, roofs, roadways and sidewalks in the industrial area, utility poles, unmanned machinery, concrete... areas above 6 feet in height, roofs, asphalt roadways, concrete roadways, wooden utility poles, unmanned..., metals, glass, aluminum siding, and enameled or laminated surfaces. Low-concentration PCBs means PCBs...

40 CFR 761.123 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., floors, roofs, roadways and sidewalks in the industrial area, utility poles, unmanned machinery, concrete... areas above 6 feet in height, roofs, asphalt roadways, concrete roadways, wooden utility poles, unmanned..., metals, glass, aluminum siding, and enameled or laminated surfaces. Low-concentration PCBs means PCBs...

Repair of impact damaged utility poles with fiber reinforced polymers (FRP), phase II.

DOT National Transportation Integrated Search

2015-06-01

Vehicle collisions with steel or aluminum utility poles are common occurrences that yield substantial but often repairable : damage. This project investigates the use of a fiber-reinforced polymer (FRP) composite system for in situ repair that : mini...

Pole pulling apparatus and method

DOEpatents

McIntire, Gary L.

1989-01-01

An apparatus for removal of embedded utility-type poles which removes the poles quickly and efficiently from their embedded position without damage to the pole or surrounding structures. The apparatus includes at least 2 piston/cylinder members equally spaced about the pole, and a head member affixed to the top of each piston. Elongation of the piston induces rotation of the head into the pole to increase the gripping action and reduce slippage. Repeated actuation and retraction of the piston and head member will "jack" the pole from its embedded position.

Carbon sequestration and natural longleaf pine ecosystems

Treesearch

Ralph S. Meldahl; John S. Kush

2006-01-01

A fire-maintained longleaf pine (Pinus palustris Mill.) ecosystem may offer the best option for carbon (C) sequestration among the southern pines. Longleaf is the longest living of the southern pines, and products from longleaf pine will sequester C longer than most since they are likely to be solid wood products such as structural lumber and poles....

10. VIEW EAST (93 DEGREES) OF RCA COMMUNICATION RECEIVING STATION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. VIEW EAST (93 DEGREES) OF RCA COMMUNICATION RECEIVING STATION. WOOD FRAMING SUPPORTED STANDOFF INSULATORS AND ANTENNA WIRES COMING FROM THE FIELD INTO THE BUILDING. BOLT ON FOUNDATION POLES SUPPORTED SATELLITE ANTENNAS, METAL CAP AND POSTS AT LEFT PROTECTED CONDUIT SUPPLYING POWER TO SATELLITE ANTENNA MOTORS. - Marconi Radio Sites, Receiving, Point Reyes Station, Marin County, CA

Wood resource

Treesearch

John R. Jones; Norbert V. DeByle; Robert P. Winokur

1985-01-01

Aspen has not been cut extensively in the West; in fact, it has been grossly underutilized. For example, as recently as 1975, the aspen harvest from National Forests in four Forest Service regions in the Rocky Mountain area was 7.64 million board feet. Additional minor volumes were cut on special-use permits for products such as fuel and corral poles. The total amount...

47 CFR 1.1402 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... respect to poles, the term usable space means the space on a utility pole above the minimum grade level... space occupied by the utility. With respect to conduit, the term usable space means capacity within a... together with their supporting infrastructure. (k) The term duct means a single enclosed raceway for...

Treatability of U.S. wood species with pigment emulsified creosote

Treesearch

Douglas M. Crawford; Rodney C. De Groot; John B. Watkins; Harry Greaves; Karl J. Schmalzl; T. L. Syers

2000-01-01

Since the 1920s creosote has been used extensively in the United States for treatment of construction timbers, poles, and posts. However, creosote has the tendency to exude or bbleedc from some treated commodities, producing a tar-like covered surface. In the United States, creosote-treated products exhibiting cleaner dried surfaces and a reduced tendency to bleed have...

Mangroves of Kiribati - A Priceless Resource Needs Protection

Treesearch

James Denny Ward

1998-01-01

Mangrove forests grow naturally along the ocean and lagoons on the islands of Kiribati. For centuries mangroves have provided wood for fuel, posts, poles, boats, houses, fences, walls, and furniture, and have been used to stake fish traps, to cultivate seaweed, and to dye and preserve canoe sails and clothing. Mangrove leaves and flowers are used in garlands and leis...

Strength of single-pole utility structures

Treesearch

Ronald W. Wolfe

2006-01-01

This section presents three basic methods for deriving and documenting Rn as an LTL value along with the coefficient of variation (COVR) for single-pole structures. These include the following: 1. An empirical analysis based primarily on tests of full-sized poles. 2. A theoretical analysis of mechanics-based models used in...

Effect of oak wood barrel capacity and utilization time on phenolic and sensorial profile evolution of an Encruzado white wine.

PubMed

Nunes, Paulo; Muxagata, Sara; Correia, Ana C; Nunes, Fernando M; Cosme, Fernanda; Jordão, António M

2017-11-01

Several studies have reported the influence of diverse winemaking technologies in white wine characteristics. However, the impact of the use of different oak wood barrel capacities and utilization time on the evolution of white wine phenolic content and sensorial characteristics are not usually considered. Thus the aim of this work was to evaluate the effect of oak wood barrel capacity and utilization time on the evolution of phenolic compounds, browning potential index and sensorial profile of an Encruzado white wine. For the 180 aging days considered, the use of new oak wood barrels induced a greater increase in global phenolic composition, including several individual compounds, such as gallic and ellagic acid, independently of the barrel capacity. Tendency for a lesser increase of the browning potential index values was detected for white wines aged in new oak wood barrels. The sensorial profile evolution, showed significant differences only for the aroma descriptors, namely for 'wood aroma' and 'aroma intensity', white wine aged in 225 L new oak wood barrels being the highest scored. The results show that, in general, the use of different capacities and utilization time of oak wood barrels used for white wine aging could play an important role in white wine quality. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Condition Assessment of Foundation Piles and Utility Poles Based on Guided Wave Propagation Using a Network of Tactile Transducers and Support Vector Machines

PubMed Central

Yu, Yang; Niederleithinger, Ernst; Li, Jianchun; Wiggenhauser, Herbert

2017-01-01

This paper presents a novel non-destructive testing and health monitoring system using a network of tactile transducers and accelerometers for the condition assessment and damage classification of foundation piles and utility poles. While in traditional pile integrity testing an impact hammer with broadband frequency excitation is typically used, the proposed testing system utilizes an innovative excitation system based on a network of tactile transducers to induce controlled narrow-band frequency stress waves. Thereby, the simultaneous excitation of multiple stress wave types and modes is avoided (or at least reduced), and targeted wave forms can be generated. The new testing system enables the testing and monitoring of foundation piles and utility poles where the top is inaccessible, making the new testing system suitable, for example, for the condition assessment of pile structures with obstructed heads and of poles with live wires. For system validation, the new system was experimentally tested on nine timber and concrete poles that were inflicted with several types of damage. The tactile transducers were excited with continuous sine wave signals of 1 kHz frequency. Support vector machines were employed together with advanced signal processing algorithms to distinguish recorded stress wave signals from pole structures with different types of damage. The results show that using fast Fourier transform signals, combined with principal component analysis as the input feature vector for support vector machine (SVM) classifiers with different kernel functions, can achieve damage classification with accuracies of 92.5% ± 7.5%. PMID:29258274

Wood-Destroying Soft Rot Fungi in the Historic Expedition Huts of Antarctica

PubMed Central

Blanchette, Robert A.; Held, Benjamin W.; Jurgens, Joel A.; McNew, Douglas L.; Harrington, Thomas C.; Duncan, Shona M.; Farrell, Roberta L.

2004-01-01

Three expedition huts in the Ross Sea region of Antarctica, built between 1901 and 1911 by Robert F. Scott and Ernest Shackleton, sheltered and stored the supplies for up to 48 men for 3 years during their explorations and scientific investigation in the South Pole region. The huts, built with wood taken to Antarctica by the early explorers, have deteriorated over the past decades. Although Antarctica has one of the coldest and driest environments on earth, microbes have colonized the wood and limited decay has occurred. Some wood in contact with the ground contained distinct microscopic cavities within secondary cell walls caused by soft rot fungi. Cadophora spp. could be cultured from decayed wood and other woods sampled from the huts and artifacts and were commonly associated with the soft rot attack. By using internal transcribed spacer sequences of ribosomal DNA and morphological characteristics, several species of Cadophora were identified, including C. malorum, C. luteo-olivacea, and C. fastigiata. Several previously undescribed Cadophora spp. also were found. At the Cape Evans and Cape Royds huts, Cadophora spp. commonly were isolated from wood in contact with the ground but were not always associated with soft rot decay. Pure cultures of Cadophora used in laboratory decay studies caused dark staining of all woods tested and extensive soft rot in Betula and Populus wood. The presence of Cadophora species, but only limited decay, suggests there is no immediate threat to the structural integrity of the huts. These fungi, however, are widely found in wood from the historic huts and have the capacity to cause extensive soft rot if conditions that are more conducive to decay become common. PMID:15006750

A red-tailed hawk at KSC

NASA Technical Reports Server (NTRS)

2000-01-01

At KSC, a red-tailed hawk waits on top of a utility pole for the slightest movement in the grass below. It feeds mostly on small rodents. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects.

KSC-00pp1740

NASA Image and Video Library

2000-11-10

KENNEDY SPACE CENTER, FLA. -- From the top of a utility pole, a red-tailed hawk launches into flight, perhaps after spotting prey, typically a small rodent. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

KSC00pp1739

NASA Image and Video Library

2000-11-10

KENNEDY SPACE CENTER, FLA. -- At KSC, a red-tailed hawk waits on top of a utility pole for the slightest movement in the grass below. It feeds mostly on small rodents. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

KSC00pp1740

NASA Image and Video Library

2000-11-10

KENNEDY SPACE CENTER, FLA. -- From the top of a utility pole, a red-tailed hawk launches into flight, perhaps after spotting prey, typically a small rodent. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

KSC-00pp1739

NASA Image and Video Library

2000-11-10

KENNEDY SPACE CENTER, FLA. -- At KSC, a red-tailed hawk waits on top of a utility pole for the slightest movement in the grass below. It feeds mostly on small rodents. Ranging in height from 18 inches to 25 inches, the species has a stocky build with a whitish breast and rust-colored tail. It has a high-pitched descending scream with a hoarse quality. The hawk inhabits mainly deciduous forest and adjacent open country from Alaska and Nova Scotia south to Panama. KSC shares a boundary with the Merritt Island National Wildlife Refuge, which encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

76 FR 30940 - Information Collection Being Submitted to the Office of Management and Budget for Emergency...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-27

... Control Number: 3060-XXXX. Title: Sections 1.1420; 1.1422; and 1.1424 Pole Attachment Access Requirements... mandate that communications companies (attachers) should be able to place facilities on utility poles. The... include the pole owner notifying all known entities with existing attachments and the requesting attacher...

Elementary budget of stag beetle larvae associated with selective utilization of nitrogen in decaying wood.

PubMed

Tanahashi, Masahiko; Ikeda, Hiroshi; Kubota, Kôhei

2018-05-03

Wood degradation by insects plays important roles for the forest matter cycling. Since wood is deficient in nitrogen compared to the insect body, wood-feeding insects need to assimilate the nitrogen selectively and discard an excess carbon. Such a stoichiometric imbalance between food and body will cause high metabolic cost; therefore, wood-feeding insects may somehow alleviate the stoichiometric imbalance. Here, we investigated the carbon and nitrogen budgets of the larvae of stag beetle, Dorcus rectus, which feed on decaying wood. Assimilation efficiency of ingested wood was 22%, and those values based on the carbon and nitrogen were 27 and 45%, respectively, suggesting the selective digestion of nitrogen in wood. Element-based gross growth efficiency was much higher for nitrogen (45%) than for carbon (3%). As a result, the larvae released 24% of the ingested carbon as volatile, whereas almost no gaseous exchange was observed for nitrogen. Moreover, solubility-based elementary analysis revealed that the larvae mainly utilized alkaline-soluble-water-insoluble fraction of wood, which is rich in nitrogen. Actually, the midgut of the larvae was highly alkaline (pH 10.3). Stag beetle larvae are known to exhibit coprophagy, and here we also confirmed that alkaline-soluble-water-insoluble nitrogen increased again from fresh feces to old feces in the field. Stable isotope analysis suggested the utilization of aerial nitrogen by larvae; however, its actual contribution is still disputable. Those results suggest that D. rectus larvae selectively utilize alkaline-soluble nitrogenous substrates by using their highly alkaline midgut, and perhaps associate with microbes that enhance the nitrogen recycling in feces.

Elementary budget of stag beetle larvae associated with selective utilization of nitrogen in decaying wood

NASA Astrophysics Data System (ADS)

Tanahashi, Masahiko; Ikeda, Hiroshi; Kubota, Kôhei

2018-06-01

Wood degradation by insects plays important roles for the forest matter cycling. Since wood is deficient in nitrogen compared to the insect body, wood-feeding insects need to assimilate the nitrogen selectively and discard an excess carbon. Such a stoichiometric imbalance between food and body will cause high metabolic cost; therefore, wood-feeding insects may somehow alleviate the stoichiometric imbalance. Here, we investigated the carbon and nitrogen budgets of the larvae of stag beetle, Dorcus rectus, which feed on decaying wood. Assimilation efficiency of ingested wood was 22%, and those values based on the carbon and nitrogen were 27 and 45%, respectively, suggesting the selective digestion of nitrogen in wood. Element-based gross growth efficiency was much higher for nitrogen (45%) than for carbon (3%). As a result, the larvae released 24% of the ingested carbon as volatile, whereas almost no gaseous exchange was observed for nitrogen. Moreover, solubility-based elementary analysis revealed that the larvae mainly utilized alkaline-soluble-water-insoluble fraction of wood, which is rich in nitrogen. Actually, the midgut of the larvae was highly alkaline (pH 10.3). Stag beetle larvae are known to exhibit coprophagy, and here we also confirmed that alkaline-soluble-water-insoluble nitrogen increased again from fresh feces to old feces in the field. Stable isotope analysis suggested the utilization of aerial nitrogen by larvae; however, its actual contribution is still disputable. Those results suggest that D. rectus larvae selectively utilize alkaline-soluble nitrogenous substrates by using their highly alkaline midgut, and perhaps associate with microbes that enhance the nitrogen recycling in feces.

Close woods utilization commonly practiced in Delaware

Treesearch

Wayne G. Banks

1956-01-01

Woods-utilization studies were recently made on randomly selected logging operations scattered throughout Delaware. As would be expected, most of the operations studied were in pine stands in the southern part of the state. They showed that very close utilization of the trees cut was the general rule.

Better utilization of low-grade woods

Treesearch

Peter Koch

1957-01-01

The objective of this paper is threefold: to outline briefly some of the avenues of approach so far employed in utilizing low-grade wood, to comment on the economic aspects of the problem, and finally, to speculate about what developments the future might bring to the field of utilization.

External electro-optic sampling utilizing a poled polymer asymmetric Fabry Perot cavity as an electro-optical probe tip

NASA Astrophysics Data System (ADS)

Chen, Kaixin; Zhang, Hongbo; Zhang, Daming; Yang, Han; Yi, Maobin

2002-09-01

External electro-optic sampling utilizing a poled polymer asymmetry Fabry-Perot cavity as electro-optic probe tip has been demonstrated. Electro-optical polymer spin coated on the high-reflectivity mirror (HRM) was corona poled. Thus, an asymmetric F-P cavity was formed based on the different reflectivity of the polymer and HRM and it converted the phase modulation that originates from electro-optic effect of the poled polymer to amplitude modulation, so only one laser beam is needed in this system. The principle of the sampling was analyzed by multiple reflection and index ellipsoid methods. A 1.2 GHz microwave signal propagating on coplanar waveguide transmission line was sampled, and the voltage sensitivity about 0.5 mV/ Hz was obtained.

Wood adhesives : vital for producing most wood products

Treesearch

Charles R. Frihart

2011-01-01

A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

Characterization of Juvenile wood in Lodgepole Pine in the Intermountain West

Treesearch

Thomas M. Gorman; David E. Kretschmann

2012-01-01

Juvenile wood (core wood) is typically characterized as being less dimensionally stable and having lower mechanical properties than mature wood. Determination of the age of transition from juvenile wood to mature wood can provide basic information needed to assess dimensional stability and better utilize small-diameter trees growing in the intermountain west as solid-...

Achievements in the utilzation of poplar wood : guideposts for the future : [abstract

Treesearch

John J. Balatinecz; Andre Leclercq; David E. Kretschmann

2000-01-01

Poplar wood is suitable and is utilized for a broad range of forest products worldwide. The utilization of any species is governed by a number of factors, such as basic wood properties, overall quality, quantity and price of the resource, available processing technologies, local as well as international market conditions for the products, and the availability and price...

Particulate matter emissions from combustion of wood in district heating applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghafghazi, S.; Sowlati, T.; Sokhansanj, Shahabaddine

2011-01-01

The utilization of wood biomass to generate district heat and power in communities that have access to this energy source is increasing. In this paper the effect of wood fuel properties, combustion condition, and flue gas cleaning system on variation in the amount and formation of particles in the flue gas of typical district heating wood boilers are discussed based on the literature survey. Direct measurements of particulate matter (PM) emissions from wood boilers with district heating applications are reviewed and presented. Finally, recommendations are given regarding the selection of wood fuel, combustion system condition, and flue gas cleaning systemmore » in district heating systems in order to meet stringent air quality standards. It is concluded that utilization of high quality wood fuel, such as wood pellets produced from natural, uncontaminated stem wood, would generate the least PM emissions compared to other wood fuel types. Particulate matter emissions from grate burners equipped with electrostatic precipitators when using wood pellets can be well below stringent regulatory emission limit such as particulate emission limit of Metro Vancouver, Canada.« less

Applications of harvesting system simulation to timber management and utilization analyses

Treesearch

John E. Baumgras; Chris B. LeDoux

1990-01-01

Applications of timber harvesting system simulation to the economic analysis of forest management and wood utilization practices are presented. These applications include estimating thinning revenue by stand age, estimating impacts of minimum merchantable tree diameter on harvesting revenue, and evaluating wood utilization alternatives relative to pulpwood quotas and...

Force interaction and 3D pole movement in double poling.

PubMed

Stöggl, T; Holmberg, H-C

2011-12-01

The aim of this study was to analyze double poling using combined kinetic and 3D kinematic analysis at high skiing speeds as regards pole force components, pole angles and pole behavior during the poling and swing phase. The hypothesis was that a horizontal pole force is more predictive for maximal skiing speed (V(max)) than the resultant pole force. Sixteen elite skiers performed a double-poling V(max) test while treadmill roller skiing. Pole forces and 3D kinematics of pole movement at a speed of 30 km/h were analyzed and related to V(max). The duration of the "preparation phase" showed the strongest relationship with V(max) (r=0.87, P<0.001). Faster skiers generated longer cycle lengths with longer swing and poling times, had less inclined pole angles at pole plant and a later peak pole force. Horizontal pole forces were not more highly related to V(max) compared with the resultant pole force. Impact force was not related to V(max). At high skiing speeds, skiers should aim to combine high pole forces with appropriate timing of pole forces and appropriate pole and body positions during the swing and poling phase. The emphasis in training should be on the development of specific strength capacities for pole force production and the utilization of these capacities in double-poling training sessions. © 2011 John Wiley & Sons A/S.

Changing Face of Wood Science in Modern Era: Contribution of Nanotechnology.

PubMed

Mishra, Pawan Kumar; Giagli, Kyriaki; Tsalagkas, Dimitrios; Mishra, Harshita; Talegaonkar, Sushma; Gryc, Vladimír; Wimmer, Rupert

2018-02-14

Wood science and nanomaterials science interact together in two different aspects; a) fabrication of lignocellulosic nanomaterials derived from wood and plant-based sources and b) surface or bulk wood modification by nanoparticles. In this review, we attempt to visualize the impact of nanoparticles on the wood coating and preservation treatments based on a thorough registration of the patent databases. The study was carried out as an overview of the scientifically most followed trends on nanoparticles utilization in wood science and wood protection depicted by recent universal filed patents. This review is exclusively targeted on the solid (timber) wood as a subject material. Utilization of mainly metal nanoparticles as photoprotection, antibacterial, antifungal, antiabrasive and functional component on wood modification treatments was found to be widely patented. Additionally, an apparent minimization in the emission of volatile organic compounds (VOCs) has been succeeded. Bulk wood preservation and more importantly, wood coating, splay the range of strengthening wood dimensional stability and biological degradation, against moisture absorption and fungi respectively. Nanoparticle materials have addressed various issues of wood science in a more efficient and environmental way than the traditional methods. Nevertheless, abundant tests and regulations are still needed before industrializing or recycling these products. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1LIGHT THREE PANEL WOOD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1-LIGHT THREE PANEL WOOD OUTSIDE DOOR SOUTH SIDE OF HOUSE, PLUMBING HOOKUPS FOR WASHER BELOW BUILT-IN CABINETS AT PHOTO LEFT, AND PAIRED ARRANGEMENTS OF 4-LIGHT OVER 4-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS ON SOUTH AND WEST WALLS. VIEW TO SOUTH. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Molecular Dissection of Xylan Biosynthesis During Wood Formation in Poplar

EPA Science Inventory

Xylan, being the second most abundant polysaccharide in dicot wood, is considered to be one of the factors contributing to wood biomass recalcitrance for biofuel production. To better utilize wood as biofuel feedstock, it is crucial to functionally characterize all the genes invo...

Estimated Hardwood Volume Available for Wood Chipmills or Other Low Grade Uses

EPA Pesticide Factsheets

The potential of wood chip mills to influence the distribution of harvests and the dynamics of wood fiber utilization has become an issue of concern. Where wood chip mills are active in a timber market, they may increase the utilization of wood fiber derived from a given harvest; change the pattern and distribution of harvests on the landscape; and reduce production costs of fiber supply, thus increasing overall quantity supplied in a price-taking market. Wood chip mills have proliferated in the South in recent decades. This data layer was created to address the following question: If the Mid-Atlantic region behaves as the South, which areas are relatively more attractive as sources of low grade hardwood fiber, and therefore relatively more vulnerable to any negative stresses associated with wood chip harvests? The data layer simulates annual softwood wood chip volume (in tons) available to supply chip mills or other low grade uses, if timber supply in the Mid-Atlantic mirrors trends for the South.

TREATMENT TECHNOLOGY PERFORMANCE AND COST DATA FOR REMEDIATION OF WOOD PRESERVING SITES

EPA Science Inventory

Wood preserving has been an industry in North America for more than 100 years. During this time wood preserving facilities have utilized a variety of compounds, including pentachlorophenol (PCP), creosote, and certain metals to extend the useful life of wood products. Past operat...

Detection of discoloration and decay in living trees and utility poles

Treesearch

Alex L. Shigo; Alex Shigo

1974-01-01

A method is described for detecting discoloration and decay in living trees and creosoted utility poles. The method and devices have come from research involving many people over a seven-year period. A probe was inserted into a 3/32-inch (2.4 mm) diameter hole made by drill bits 8 inches (20.32 cm) and 12 inches (30.48 cm) long mounted in a portable, light-weight,...

Industrial wood productivity in the United States, 1900-1998

Treesearch

Peter J. Ince

2000-01-01

The productivity of U.S. wood and paper product output in terms of wood input is computed and displayed in graphs. Background tables provide supporting data. The productivity trend parallels trends in the recovered paper utilization rate. Recycling and wood residue use are key factors in productivity gains.

Variation of arsenic concentration on surfaces of in-service CCA-treated wood planks in a park and its influencing field factors.

PubMed

Tang, Ya; Gao, Wei; Wang, Xiuli; Ding, Shiming; An, Taicheng; Xiao, Weiyang; Wong, Ming H; Zhang, Chaosheng

2015-01-01

Wood preservatives can protect wood from dry rot, fungi, mould and insect damage, and chromated copper arsenate (CCA) has been used as an inorganic preservative for many years. However, wood treated with CCA has been restricted from residential uses in the EU from June 30, 2004, due to its potential toxicity. Such a regulation is not in place in China yet, and CCA-treated wood is widely used in public parks. A portable XRF analyser was used to investigate arsenic (As) concentration on surfaces of in-service CCA-treated wood planks in a popular park as well as the influencing field factors of age in-service, immersion and human footfall. With a total of 1207 readings, the observed As concentrations varied from below the detection limit (<10 mg/kg) to 15,746 mg/kg with a median of 1160 mg/kg. Strong variation of As concentrations were observed in different wood planks of the same age, on the surface of the same piece of wood, inside the same piece of wood, and different surfaces of walkway planks, hand rails and poles in the field. The oldest planks exhibited high As concentrations, which was related to its original treatment with high retention of CCA preservative. The effect of immersion in the field for about 4 months was insignificant for As concentration on the surfaces. However, a significant reduction of As was observed for immersion combined with human footfall (wiping by shoes). Human traffic in general caused slightly reduced and more evenly distributed As concentrations on the wood surfaces. The strong variation, slow aging and relatively weak immersion effects found in this study demonstrate that the in-service CCA-treated wood poses potential health risks to the park users, due to easy dermal contact especially when the wood is wet after rainfall. It is suggested that further comprehensive investigations and risk assessments of CCA-treated wood in residential areas in China are needed, and precautionary measures should be considered to reduce the potential risks to residents and visitors, especially children.

Some preliminary estimates of energy utilization in even-aged northern hardwoods

Treesearch

William B. Leak

1970-01-01

Estimates of energy utilization from various sources indicate that even-aged northern hardwood stands utilize less than 1/2 percent of net solar radiation for wood, leaf, and seed production, and only about 1/10 percent for production of merchantable wood. Forest managers should seek to understand and manipulate the remaining 99+ percent of solar energy, for improving...

Wood-Based Nanocomposite Derived by in Situ Formation of Organic-Inorganic Hybrid Polymer within Wood via a Sol-Gel Method.

PubMed

Dong, Xiaoying; Zhuo, Xiao; Wei, Jie; Zhang, Gang; Li, Yongfeng

2017-03-15

Solid wood materials and wood-plastic composites as two kinds of lightweight materials are attracting great interest from academia and industry due to their green and recycling nature. However, the relatively lower specific strength limits their wider applications. In particular, solid wood is vulnerable to moisture and decay fungi in nature, resulting in its poor durability for effectively long-term utilization. Inspired from the porous structure of wood, we propose a new design to build a wood-based nanocomposite with higher specific strength and satisfactory durability by in situ generation of organic-inorganic hybrid polymer within wood via a sol-gel method. The derived composite has 50-1200% improvement of impact toughness, 56-192% improvement of tensile strength, and 110-291% improvement of flexural strength over those of typical wood-plastic composites, respectively; and even 34% improvement of specific tensile strength than that of 36A steel; 208% enhancement of hardness; and 156% enhancement of compression strength than those of compared solid wood, respectively; as well as significantly improved dimensional stability and decay resistance over those of untreated natural wood. Such materials could be potentially utilized as lightweight and high-strength materials for applications in construction and automotive industries. This method could be extended to constitute other inorganic nanomaterials for novel organic-inorganic hybrid polymer within wood.

Conceptual and empirical themes regarding the design of technology transfer programs : a review of wood utilization research in the United States

Treesearch

Paul V. Ellefson; Michael A. Kilgore; Kenneth E. Skog; Christopher D. Risbrudt

2011-01-01

Transfer of technologies produced by research is critical to innovation within all organizations. The intent of this paper is to take stock of the conceptual underpinnings of technology transfer processes as they relate to wood utilization research and to identify conditions that promote the successful transfer of research results. Conceptually, research utilization...

Detection and Classification of Pole-Like Objects from Mobile Mapping Data

NASA Astrophysics Data System (ADS)

Fukano, K.; Masuda, H.

2015-08-01

Laser scanners on a vehicle-based mobile mapping system can capture 3D point-clouds of roads and roadside objects. Since roadside objects have to be maintained periodically, their 3D models are useful for planning maintenance tasks. In our previous work, we proposed a method for detecting cylindrical poles and planar plates in a point-cloud. However, it is often required to further classify pole-like objects into utility poles, streetlights, traffic signals and signs, which are managed by different organizations. In addition, our previous method may fail to extract low pole-like objects, which are often observed in urban residential areas. In this paper, we propose new methods for extracting and classifying pole-like objects. In our method, we robustly extract a wide variety of poles by converting point-clouds into wireframe models and calculating cross-sections between wireframe models and horizontal cutting planes. For classifying pole-like objects, we subdivide a pole-like object into five subsets by extracting poles and planes, and calculate feature values of each subset. Then we apply a supervised machine learning method using feature variables of subsets. In our experiments, our method could achieve excellent results for detection and classification of pole-like objects.

JPL-20180411-JUNOf-0002-Flyover of Jupiters North Pole in Infrared

NASA Image and Video Library

2018-04-11

This flyover of Jupiter's North Pole utilizes data collected by the Jovian Infrared Auroral Mapper (JIRAM) instrument on NASA's Juno spacecraft. It illustrates the 3-D aspects of the region's central cyclone and the eight cyclones that encircle it.

Properties and utilization of poplar wood

Treesearch

John J. Balatinecz; David E. Kretschmann

2001-01-01

Hybrid poplars are fast-growing, moisture-loving, full-sun-loving large trees that can be a rapid source of wood fiber. With the introduction of waferboard, oriented strandboard (OSB), and laminated strand lumber (LSL), aspen utilization has dramatically increased. Indigenous and hybrid poplars, however, present their own challenges, such as high discoloration...

Twin Valley, Wild Rice River, Minnesota. Addendum.

DTIC Science & Technology

1976-05-01

acres each and one having a drainage area of over 13,000 acres. Along with the impoundment program, p!-oper management of soil and water is stressed ...diversity of both plants and animals associated with this ecotone and stresses its importance: first, because it is an ecotone, and second, because it...1969. Pole stage aspen woods. Thirty-third breeding bird census. Aud. Field Notes 23: 712-713. Cumins , K.W. 1962. An evaluation of some techniques for

Wood and society

Treesearch

Christopher D. Risbrudt

2005-01-01

Forests, and the wood they produce, have played an important role in human activity since before recorded history. Indeed, one of the first major innovations of humankind was utilizing fire, fueled by wood, for cooking and heating. It is very likely that early hominids used wood fires for cooking as long as 1.5 million years ago (Clark and Harris 1985). Clear evidence...

GC-MS Characterizations of Termiticidal Heartwood Extractives from Wood Species Utilized in Pakistan

Treesearch

Mark Mankowski; Blossie Boyd; Barbar Hassan; Grant T. Kirker

2016-01-01

Wood species that exhibit innate tolerance to wood destroying organisms such as termites are considered to be naturally durable. This durability can, in part, be due to the complex chemical compounds in the heartwood of naturally durable wood species. We examined the effects of varying concentrations of heartwood extractives on the subterranean termite, ...

Strength and stiffness assessment of standing trees using a nondestructive stress wave technique.

Treesearch

Xiping Wang; Robert J. Ross; Michael McClellan; R. James Barbour; John R. Erickson; John W. Forsman; Gary D. McGinnis

Natureas engineering of wood through genetics, stand conditions, and environment creates wide variability in wood as a material, which in turn introduces difficulties in wood processing and utilization. Manufacturers sometimes find it difficult to consistently process wood into quality products because of its wide range of properties. The primary objective of this...

Using a wood stove to heat greenhouses

Treesearch

Gloria Whitefeather-Spears

2009-01-01

The Red Lake Tribal Forestry Greenhouse in Red Lake, MN, utilizes four types of outdoor furnaces for heating through the fall, winter, and spring. The WoodMaster® is a highly efficient, wood-fired furnace that provides forced-air heat to the greenhouse. The HeatmorTM furnace is an economical wood-fired alternative that can provide lower...

Common questions and concerns from government users of industrial treated wood products

Treesearch

Stan Lebow; James Wacker

2011-01-01

Because pressure-treated wood is perceived as economical and relatively easy to install, federal, state and local government agencies sometimes utilize treated wood for industrial-type applications. When these agencies have questions or concerns about treated wood they may make inquiries to the US Forest Products Laboratory. These inquiries provide an indication of...

CAMP LEJEUNE ENERGY FROM WOOD (CLEW) PROJECT

EPA Science Inventory

The paper discusses EPA's Camp Lejeune Energy from Wood (CLEW) project, a demonstration project that converts wood energy to electric power, and provides waste utilization and pollution alleviation. The 1-MWe plant operates a reciprocating engine-generator set on synthetic gas f...

Chapter 1: Wood and Society

Treesearch

Chrisopher D. Risbrudt

2013-01-01

Forests, and the wood they produce, have played an important role in human activity since before recorded history. Indeed, one of the first major innovations was utilizing fire, fueled by wood, for cooking and heating. It is very likely that early hominids used wood fires for cooking, as long as 1.5 million years ago (Clark and Harris 1985). Clear evidence of this use...

Remilling of salvaged wood siding coated with lead-based paint. Part 2, Wood product yield

Treesearch

John J. Janowiak; Robert H. Falk; Brian W. Beakler; Richard G. Lampo; Thomas R. Napier

2005-01-01

Many U.S. military buildings being targeted for removal contain large quantities of potentially reusable wood materials. In this study, we evaluated approximately 2180 m (7,152 ft) of painted Douglas-fir siding salvaged from U.S. Army barracks. Utilizing a conventional woodworking molder, we evaluated the feasibility of producing several standardized wood product...

Government policies increasingly promote renewable energy sources : wood energy markets in the UNECE region, 2009-2010

Treesearch

Olle Olsson; Bengt Hillring; Rens Hartkamp; Kenneth Skog; Henry Spelter; Francisco Aguilar; Warren Mabee; Christopher Gaston; Antje Wahl

2010-01-01

Sustainability issues about wood fuels are increasingly being debated, but the European Union has decided not to impose EU-wide sustainability criteria for solid biomass. United Kingdom energy companies plan massive increases in their utilization of wood energy, further fuelling European demand for wood energy. In order to increase control of the value chain, European...

Estimated Softwood Volume Available for Wood Chipmills or other Low Grade Uses.

EPA Pesticide Factsheets

The potential of wood chip mills to influence the distribution of harvests and the dynamics of wood fiber utilization has become an issue of concern. Where wood chip mills are active in a timber market, they may increase the utilization of wood fiber derived from a given harvest; change the pattern and distribution of harvests on the landscape; and reduce production costs of fiber supply, thus increasing overall quantity supplied in a price-taking market. Wood chip mills have proliferated in the South in recent decades. This data layer was created to address the following question: If the Mid-Atlantic region behaves as the South, which areas are relatively more attractive as sources of low grade softwood fiber, and therefore relatively more vulnerable to any negative stresses associated with wood chip harvests? The data layer simulates annual softwood wood chip volume (in tons) available to supply chip mills or other low grade uses, if timber supply in the Mid-Atlantic mirrors trends for the South. More information about these resources, including the variables used in this study, may be found here: https://edg.epa.gov/data/Public/ORD/NERL/ReVA/ReVA_Data.zip.

Some thoughts on wood utilization research

Treesearch

P. Koch

1980-01-01

For over 17 years our small group of scientists has worked to improve utilization of southern wood species. From these years of experience, I have distilled some thoughts on research objectives, attributes of scientists who accomplish the objectives, administration of research, and transferring results from laboratory to industry. I would like to share these thoughts...

Bark And Its Possible Uses

Treesearch

J. M. Harkin; J. W. Rowe

1971-01-01

What to do with bark is a major question facing the wood conversion industries. Optimum utilization of bark residues demands appreciation of the complexity of bark and the extreme variation in chemical and physical properties between barks of different wood species. This report discusses bark structure, past and present utilization, and methods of upgrading bark both...

Movement and fate of creosote waste in ground water, Pensacola, Florida; U.S. Geological Survey toxic waste-ground-water contamination program

USGS Publications Warehouse

Mattraw, Harold C.; Franks, Bernard J.

1986-01-01

Ground- and surface-water contamination by pesticides used in the wood-preserving industry is widespread in the United States. Pine poles were treated with wood preservatives from 1902 to 1981 at a creosote works near Pensacola, Florida. Diesel fuel, creosote, and pentachlorophenol were discharged to two unlined impoundments that had a direct hydraulic connection to the sand-and-gravel aquifer. Evidence of wood-preserving waste contamination appears to be confined to the upper 30 meters of the aquifer. The waste plume extends downgradient approximately 300 meters south toward Pensacola Bay. In 1983, the creosote works site was selected by the U.S. Geological Survey's Office of Hazardous Waste Hydrology as a national research demonstration area to apply the latest techniques for characterizing hazardous waste problems. The multidisciplinary research effort is aimed at studying processes that affect the occurrence, transport, transformations, and fate of the toxic contaminants associated with wood preservatives in the environment. Clusters of two to five wells were constructed at different depths at nine sites to define the depth of contamination. Research studies are investigating sorption, dispersion, dilution, chemical reactions, bacterially mediated transformations, quality assurance, plume hydrodynamics, and the ultimate fate of these complex organic wastes.

An Evolutionary History of Oriented Strandboard (OSB)

Treesearch

John I. Zerbe; Zhiyong Cai; George B. Harpole

2015-01-01

To improve wood utilization efficiency, oriented strandboard (OSB) was developed; 80% of the wood removed from the forest can now be processed into marketable products. This manuscript describes the history of developing this most profitable wood product, OSB, and the early FPL contribution in development.

Characteristics of wood ash and influence on soil properties and nutrient uptake: an overview.

PubMed

Demeyer, A; Voundi Nkana, J C; Verloo, M G

2001-05-01

Wood industries and power plants generate enormous quantities of wood ash. Disposal in landfills has been for long a common method for removal. New regulations for conserving the environment have raised the costs of landfill disposal and added to the difficulties for acquiring new sites for disposal. Over a few decades a number of studies have been carried out on the utilization of wood ashes in agriculture and forestry as an alternative method for disposal. Because of their properties and their influence on soil chemistry the utilization of wood ashes is particularly suited for the fertility management of tropical acid soils and forest soils. This review principally focuses on ash from the wood industry and power plants and considers its physical, chemical and mineralogical characteristics, its effect on soil properties, on the availability of nutrient elements and on the growth and chemical composition of crops and trees, as well as its impact on the environment.

Electrical Transfer Function and Poling Mechanisms for Nonlinear Optical Polymer Modulators

NASA Technical Reports Server (NTRS)

Watson, Michael Dale

2004-01-01

Electro-Optic Polymers hold great promise in increased electro-optic coefficients as compared to their inorganic corollaries. Many researchers have focused on quantum chemistry to describe how the dipoles respond to temperature and electric fields. Much work has also been done for single layer films to confirm these results. For optical applications, waveguide structures are utilized to guide the optical waves in 3 layer stacks. Electrode poling is the only practical poling method for these structures. This research takes an electrical engineering approach to develop poling models and electrical and optical transfer functions of the waveguide structure. The key aspect of the poling model is the large boundary charge density deposited during the poling process. The boundary charge density also has a large effect on the electrical transfer function which is used to explain the transient response of the system. These models are experimentally verified. Exploratory experiment design is used to study poling parameters including time, temperature, and voltage. These studies verify the poling conditions for CLDX/APC and CLDZ/APEC guest host electro optic polymer films in waveguide stacks predicted by the theoretical developments.

Electric utilities and telecommunications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moeller, J.W.

1995-08-01

Part I of this article will provide some background on the involvement of electric utilities in telecommunications. It will discuss the Power Radio Services, under which the FCC regulates radio communications of electric utilities, the pole attachment statute of the Communications Act, which authorized the FCC to regulate attachments of cable television cables to electric utility poles, and a recent Department of Energy (DOE) report on the need for a demonstration on the use of telecommunications for DSM. Part I will also discuss several recent developments relative to the Power Radio Services and the pole attachment statute. Part II willmore » discuss electric utilities and telecommunications under PUHCA. It will outline the extensive and complex requirements of PUHCA that are applicable to public utility holding companies, as well as the specific requirements of PUHCA for the formation by public utility holding companies of subsidiaries to engage in telecommunications activities. It will also discuss the seven instances in the past decade in which the SEC has approved the formation by public utility holding companies of such subsidiaries. Part III of this article will discuss a principal obstacle to expanded electric utility involvement in telecommunications activities-a series of administrative and judicial decisions that illustrate the potential for dual regulation by the SEC and the FERC to result in confusion and inefficiencies. It will also discuss proposals in Congress to minimize this potential. Part IV will discuss House Bill 3636 and Senate Bill 1822 and their proposals to amend PUHCA to facilitate the formation or acquisition by public utility holding companies of non-utility subsidiaries to engage in telecommunications activities. It will also discuss their proposals to address the potential consequences of dual regulation by the SEC and the FERC of electric utilities involved in telecommunications.« less

Adhesive properties of water washed cottonseed meal on four types of wood

USDA-ARS?s Scientific Manuscript database

The interest in natural product-based wood adhesives has been steadily increasing due to the environmental and sustainable concerns of petroleum-based adhesives. In this work, we reported our research on the utilization of water washed cottonseed meal (WCM) as wood adhesives. The adhesive strength a...

Uses for Sawdust, Shavings, And Waste Chips

Treesearch

J. M. Harkin

1969-01-01

Although many outlets are available for the utilization of wood fines, economical disposal of sawdust, shavings, and waste chips remains a problem of growing concern to the wood industry. This report summarizes current uses for wood residues and provides sources of further information on available outlets, processing methods, and economic considerations.

Investigation of bio-composites using Novolac type liquefied wood resin: effects of liquefaction and fabrication conditions

Treesearch

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Wood liquefaction using an organic solvent and an acid catalyst has long been studied as a novel technique to utilize biomass as an alternative to petroleum-based products. Oxalic acid is a weaker organic acid than a mineral acid and wood liquefaction with oxalic acid as a catalyst will result in a higher amount of wood residue than that with a mineral acid....

A synthesis of biomass utilization for bioenergy production in the Western United States.

Treesearch

David L. Nicholls; Robert A. Monserud; Dennis P. Dykstra

2008-01-01

We examine the use of woody residues, primarily from forest harvesting or wood products manufacturing operations (and to a limited degree from urban wood wastes), as a feedstock for direct-combustion bioenergy systems for electrical or thermal power applications. We examine opportunities for utilizing biomass for energy at several scales, with an emphasis on larger...

Efficiency in wood and fiber utilization in OECD countries

Treesearch

Hiroko Kando; Joseph Buongiorno

2009-01-01

Utilization efficiency has been defined as the ratio of the amount of industrial roundwood (or wood pulp) consumed in a country and year to the amount that would have been consumed to produce the same output with a reference technology.  The reference technology was described by the average input-output relationships in countries of the Organization for Economic...

Dynamic Electromechanical Characterization of the Ferroelectric Ceramic PZT 95/5

NASA Astrophysics Data System (ADS)

Setchell, R. E.; Chhabildas, L. C.; Furnish, M. D.; Montgomery, S. T.; Holman, G. T.

1997-07-01

Shock-induced depoling of the ferroelectric ceramic PZT 95/5 has been utilized in a number of pulsed power applications. The dynamic behavior of the poled ceramic is complex, with nonlinear coupling between mechanical and electrical variables. Recent efforts to improve numerical simulations of this process have been limited by the scarcity of relevant experimental studies within the last twenty years. Consequently, we have initiated an extensive experimental study of the dynamic electromechanical behavior of this material. Samples of the poled ceramic are shocked to axial stresses from 0.5 to 5 GPa in planar impact experiments and observed with laser interferometry (VISAR) to obtain transmitted wave profiles. Current generation due to shock-induced depoling is observed using different external loads to vary electric field strengths within the samples. Experimental configurations either have the remanent polarization parallel to the direction of shock motion (axially poled) or perpendicular (normally poled). Initial experiments on unpoled samples utilized PVDF stress gauges as well as VISAR, and extended prior data on shock loading and release behavior. (Supported by the U. S. Department of Energy under contract DE-AC04-94AL85000). abstract.

Location selection and layout for LB10, a lunar base at the Lunar North Pole with a liquid mirror observatory

NASA Astrophysics Data System (ADS)

Detsis, Emmanouil; Doule, Ondrej; Ebrahimi, Aliakbar

2013-04-01

We present the site selection process and urban planning of a Lunar Base for a crew of 10 (LB10), with an infrared astronomical telescope, based on the concept of the Lunar LIquid Mirror Telescope. LB10 is a base designated for permanent human presence on the Moon. The base architecture is based on utilization of inflatable, rigid and regolith structures for different purposes. The location for the settlement is identified through a detailed analysis of surface conditions and terrain parameters around the Lunar North and South Poles. A number of selection criteria were defined regarding construction, astronomical observations, landing and illumination conditions. The location suggested for the settlement is in the vicinity of the North Pole, utilizing the geographical morphology of the area. The base habitat is on a highly illuminated and relatively flat plateau. The observatory in the vicinity of the base, approximately 3.5 kilometers from the Lunar North Pole, inside a crater to shield it from Sunlight. An illustration of the final form of the habitat is also depicted, inspired by the baroque architectural form.

Properties of seven Colombian woods

Treesearch

B. A. Bendtsen; M. Chudnoff

1981-01-01

Woods from abroad are an important raw material to the forest products industries in the United States. A major concern in effective utilization of this resource is the lack of technical information on many species. This report presents the results of an evaluation of the mechanical properties of small, clear specimens of seven Colombian woods. These results are...

Scaled-up remediation of CCA-treated wood

Treesearch

Carol A. Clausen; William R. Kenealy

2004-01-01

Bioremediation is a novel approach to recycling waste wood treated with chromated copper arsenate (CCA). Remediating CCA-treated waste wood diverts this fiber source from our landfills and provides tangible secondary products from the cleaned fiber. On a laboratory scale, this method, which utilizes oxalic acid extraction and bioleaching with a metal- tolerant...

Adhesives with wood materials : bond formation and performance

Treesearch

Charles R. Frihart; Christopher G. Hunt

2010-01-01

Adhesive bonding of wood plays an increasing role in the forest products industry and is a key factor for efficiently utilizing our timber resource. The main use of adhesives is in the manufacture of building materials, including plywood, oriented strandboard, particleboard, fiberboard, structural composite lumber, doors, windows and frames, and factory-laminated wood...

Development and application of wood adhesives in China

Treesearch

Jiyou Gu; Zhiyong Cai

2010-01-01

Rapid economic development and growth in China has resulted in a substantial increase in the demand for utilization of bio-based composites. This provides a unique opportunity for developing wood adhesives. This study reviews research development and major accomplishments in wood adhesives and technology in China over the last 50 years. It also discusses the...

Public opinion and wood energy

Treesearch

Sarah Hitchner; John Schelhas; Teppo Hujala; J. Peter Brosius

2014-01-01

As wood-based bioenergy continues to develop around the world, it will utilize forestlands in new ways and will have different effects on a number of stakeholders, including forest landowners, local communities, extant industries, policymakers, investors, and others. As more stakeholders become involved in the wood energy web, and as the general public becomes more...

Improvement of water resistance and dimensional stability of wood through titanium dioxide coating

Treesearch

Qingfeng Sun; Haipeng Yu; Yixing Liu; Jian Li; Yun Lu; John F. Hunt

2010-01-01

Moisture absorption and dimensional distortion are the major drawbacks of wood utilization as building material. In this study, poplar wood coated with a thin layer of titanium dioxide (TiO2) was prepared by the cosolvent-controlled hydrothermal method. Subsequently, its moisture absorption and dimensional stability were examined. Scanning...

Wood Export and Deposition Dynamics in Mountain Watersheds

NASA Astrophysics Data System (ADS)

Senter, Anne Elizabeth

Wood dynamics that store, transport, break down, and ultimately export wood pieces through watershed networks are key elements of stream complexity and ecosystem health. Efforts to quantify wood processes are advancing rapidly as technological innovations in field data collection, remotely sensed data acquisition, and data analyses become increasingly sophisticated. The ability to extend the temporal and spatial scales of wood data acquisition has been particularly useful to the investigations presented herein. The primary contributions of this dissertation are focused on two aspects of wood dynamics: watershed-scale wood export processes as identified using the depositional environment of a mountain reservoir, and wood deposition mechanisms in a bedrock-dominated mountain river. Three chapters present this work: In Chapter 1, continuous video monitoring of wood in transport revealed seasonal and diurnal hydrologic cycle influences on the variable rates at which wood transports. This effort supports the efficacy of utilizing continuous data collection methods for wood transport studies. Annual wood export data were collected via field efforts and aerial image analyses from New Bullards Bar Reservoir on the North Yuba River, Sierra Nevada, California. Examination of data revealed linkages between decadal-scale climatic patterns, large flood events, and episodic wood export quantities. A watershed-specific relation between wood export quantities and annual peak discharge contributes to the notion that peak discharge is a primary control on wood export, and yielded prediction of annual wood export quantities where no data were available. Linkages between seasonality, climatic components, and hydrologic events that exert variable control on watershed scale wood responses are presented as a functional framework. An accompanying conceptual model supports the framework presumption that wood responses are influenced by seasonal variations in Mediterranean-montane climate conditions and accompanying hydrologic responses. Chapter 2 contains development of new theory in support of the introduction of multiplicative coefficients, categorized by water year type, that were used to predict wood export quantities via utilization of an existing discharge-based theoretical equation. This new theory was the product of continued investigations into watershed-scale factors in search of explanation of observed variation of wood export rates into New Bullards Bar Reservoir. The gap between known variability and the attribution of wood export to one hydrologic relation continues to be a persistent issue, as the hierarchical and stochastic temporal and spatial nature of wood budget components remain difficult to quantify. The development of "watershed processes" coefficients was specifically focused on a generalized, parsimonious approach using water year type categories, with validation exercises supporting the approach. In dry years, predictions more closely represented observed wood export quantities, whereas the previously derived annual peak discharge relation yielded large over-predictions. Additional data are needed to continue development of these watershed-specific coefficients. This new approach to wood export prediction may be beneficial in regulated river systems for planning purposes, and its efficacy could be tested in other watersheds. Chapter 3 presents the results of an investigation into wood deposition mechanisms in a 12.2 km segment of the confined, bedrock-dominated South Yuba River watershed. Inclusion of coarse wood particles in the analyses was essential in recognizing depositional patterns, thus supporting the value of utilizing a wider wood-size range. A near-census data collection effort yielded myriad data, of which topographic wetted width and bed elevation data, developed for an observed 4.5-year flood event, were standardized in 10-m intervals and then univariate and linked values were ordered into landform classifications using decision tree analyses. Digital imagery collected via kite-blimp was mosaicked into a geographic information system and all resolvable wood pieces greater then 2.5 cm in one dimension were delineated and categorized into piece count density classes. Visual imagery was also key in identifying two river corridor terrains: bedrock outcrops and cobble-boulder-vegetation patches. A conceptual model framed an investigation into how topographic variability and structural elements might influence observed wood deposition dynamics. Forage ratio test results that quantified wood piece utilization versus interval availability revealed that high-density wood deposition patterns were most significantly co-located with five discrete bedrock outcrops that dominated small portions of the river corridor in high flow conditions. Topographic variations and cobble-boulder-vegetation patches were found to be subordinate factors in wood deposition patterns. Bedrock outcrops with specific structural components were the primary depositional environments that acted as floodplain extents for coarse wood deposition, with mechanisms such as topographic steering, eddying, trapping, stranding, backwater effects, and lateral roughness features inferred to be responsible for observed wood deposition patterns.

Analytical monitoring of soil bioengineering structures in the Tuscan Emilian Apennines of Italy

NASA Astrophysics Data System (ADS)

Selli, Lavinia; Guastini, Enrico

2014-05-01

Soil bioengineering has been an appropriate solution to deal with erosion problems and shallow landslides in the North Apennines, Italy. The objective of our research was a check about critical aspects of soil bioengineering works. We monitored the works that have been carried out in the Tuscan Emilian Apennines by testing the suitability of different plant species and analyzed in detail timber structures of wooden crib walls. Plant species were mainly Salix alba and Salix purpurea that gave good sprouting and survival rates. However, showed some issues in growing on dry and sunny Apennine lands, where other shrubs like Spanish Broom, blackthorn, cornel-tree and Eglantine would be more indicated. The localized analysis on wooden elements has been led gathering parts from the poles and obtaining samples in order to determine their density. The hypothetical initial density of the wood used in the structure has been estimated, then calculating the residual density. This analysis allows us to determine the general condition of the wood, highlighting the structures in worst condition (the one in Pianaccio show a residual density close to 70%, instead of 90% as found on other structures) and those whose degraded wood has undergone the greatest damage (Pianaccio here too, with 50%, followed by Campoferrario - 60% - and by Pian di Favale with 85%, a rather good value for the most degraded wood in the structure).

Periodically poled silicon

NASA Astrophysics Data System (ADS)

Hon, Nick K.; Tsia, Kevin K.; Solli, Daniel R.; Jalali, Bahram

2009-03-01

We propose a new class of photonic devices based on periodic stress fields in silicon that enable second-order nonlinearity as well as quasi-phase matching. Periodically poled silicon (PePSi) adds the periodic poling capability to silicon photonics and allows the excellent crystal quality and advanced manufacturing capabilities of silicon to be harnessed for devices based on second-order nonlinear effects. As an example of the utility of the PePSi technology, we present simulations showing that midwave infrared radiation can be efficiently generated through difference frequency generation from near-infrared with a conversion efficiency of 50%.

12. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN FOURPANEL WOOD DOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN FOUR-PANEL WOOD DOOR TO SOUTH BEDROOM AT PHOTO CENTER RIGHT, OPEN DOORWAY TO LIVING ROOM AT PHOTO CENTER LEFT, AND BUILT-IN CABINETS AND CEILING VENT BETWEEN THE DOORS AND AROUND THE STOVE/RANGE POSITION. VIEW TO NORTHEAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Low-grade and character-marked hardwoods: A research review and synthesis of solid wood manufacturing and marketing

Treesearch

David Nicholls; Matt Bumgardner

2015-01-01

There is a substantial body of research from the past half-century addressing hardwood utilization and markets in North America. This synthesis is the first to our knowledge to consider two major (and related) aspects of this research concurrently: low-grade hardwood utilization and marketing of character-marked wood features. We first consider low-grade hardwood...

Reinforcement of Wood Pallets with Metal Connector Plates

Treesearch

John W. Clarke; Thomas E. McLain; Marshall S. White; Philip A. Araman

1993-01-01

Reinforcement of the damage-prone areas of wood pallet stringers with metal connector plates (MCPs) may increase useful pallet life or permit use of less desirable wood species. This will improve the utilization of our timber resources and landfill space. Whole pallets and individual stringers, reinforced at the inner notches, were tested in static bending. Stringer...

Multidimensional NMR analysis reveals truncated lignin structures in wood decayed by the brown rot basidiomycete Postia placenta

Treesearch

Daniel J. Yelle; Dongsheng Wei; John Ralph; Kenneth E. Hammel

2011-01-01

Lignocellulose biodegradation, an essential step in terrestrial carbon cycling, generally involves removal of the recalcitrant lignin barrier that otherwise prevents infiltration by microbial polysaccharide hydrolases. However, fungi that cause brown rot of wood, a major route for biomass recycling in coniferous forests, utilize wood polysaccharides efficiently while...

"Greener" hybrid adhesives composed of urea formaldehyde resin and cottonseed meal for wood based composites

USDA-ARS?s Scientific Manuscript database

Urea formaldehyde (UF) resins are one of the most widely used adhesives in wood based composites. The major concerns of the resin utilization are free formaldehyde release and poor water resistance. As a renewable raw materials, water washed conttonseed meal can be used in wood bonding. To produce “...

Alternate biomass harvesting systems using conventional equipment

Treesearch

Bryce J. Stokes; William F. Watson; I. Winston Savelle

1985-01-01

Three harvesting methods were field tested in two stand types. Costs and stand utilization rates were developed for a conventional harvesting system, without energy wood recovery; a two-pass roundwood and energy wood system; and a one-pass system that harvests roundwood and energy wood. The systems harvested 20-acre test blocks in two pine pulpwood plantations and in a...

76 FR 57986 - Notice of Public Information Collection(s) Being Reviewed by the Federal Communications...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-19

... INFORMATION: OMB Control Number: 3060-1151. Title: Sections 1.1420, 1.1422, and 1.1424, Pole Attachment Access... place facilities on utility poles. The rules set a series of deadlines or ``timelines'' to govern the... attachments and the requesting attacher of the scheduled work. Other notification occurs if the make-ready...

Modeling a Linear Generator for Energy Harvesting Applications

DTIC Science & Technology

2014-12-01

sensors where electrical power is not available (e.g., wireless sensors on train cars). While piezoelectric harvesters are primarily utilized in...Ship and the Future of Electricity Generation ............3 2. Unmanned Sensor Energy Needs .......................................................4...18 Figure 8. Example two-pole, three-phase salient-pole synchronous machine showing the general layout of windings and major axis

Bending strength of Chilean radiata pine poles

Treesearch

Gina Cerda; Ronald W. Wolfe

2003-01-01

Because radiata pine has thrived in south-central Chile since it was introduced there more than a century ago, pine plantation productivity there has grown tremendously. Plantation owners are seeking new markets for this material. One potential market is utility poles. The American National Standards Institute 05.1 standard (ANSI 05.1) provides a means for radiata pine...

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler.

PubMed

Samaras, P; Skodras, G; Sakellaropoulos, G P; Blumenstock, M; Schramm, K W; Kettrup, A

2001-01-01

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.

Functional lignocellulosic materials prepared by ATRP from a wood scaffold.

PubMed

Cabane, Etienne; Keplinger, Tobias; Künniger, Tina; Merk, Vivian; Burgert, Ingo

2016-08-10

Wood, a natural and abundant source of organic polymers, has been used as a scaffold to develop novel wood-polymer hybrid materials. Through a two-step surface-initiated Atom Transfer Radical Polymerization (ATRP), the porous wood structure can be effectively modified with polymer chains of various nature. In the present study, polystyrene and poly(N-isopropylacrylamide) were used. As shown with various characterization techniques including confocal Raman microscopy, FTIR, and SEM/EDX, the native wood ultrastructure and features are retained and the polymer chains can be introduced deep within the wood, i.e. inside the wood cell walls. The physical properties of the new materials have been studied, and results indicate that the insertion of polymer chains inside the wood cell wall alters the intrinsic properties of wood to yield a hybrid composite material with new functionalities. This approach to the functionalization of wood could lead to the fabrication of a new class of interesting functional materials and promote innovative utilizations of the renewable resource wood.

Functional lignocellulosic materials prepared by ATRP from a wood scaffold

PubMed Central

Cabane, Etienne; Keplinger, Tobias; Künniger, Tina; Merk, Vivian; Burgert, Ingo

2016-01-01

Wood, a natural and abundant source of organic polymers, has been used as a scaffold to develop novel wood-polymer hybrid materials. Through a two-step surface-initiated Atom Transfer Radical Polymerization (ATRP), the porous wood structure can be effectively modified with polymer chains of various nature. In the present study, polystyrene and poly(N-isopropylacrylamide) were used. As shown with various characterization techniques including confocal Raman microscopy, FTIR, and SEM/EDX, the native wood ultrastructure and features are retained and the polymer chains can be introduced deep within the wood, i.e. inside the wood cell walls. The physical properties of the new materials have been studied, and results indicate that the insertion of polymer chains inside the wood cell wall alters the intrinsic properties of wood to yield a hybrid composite material with new functionalities. This approach to the functionalization of wood could lead to the fabrication of a new class of interesting functional materials and promote innovative utilizations of the renewable resource wood. PMID:27506369

Not Just Lumber—Using Wood in the Sustainable Future of Materials, Chemicals, and Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jakes, Joseph E.; Arzola, Xavier; Bergman, Rick

Forest-derived biomaterials can play an integral role in a sustainable and renewable future. Research across a range of disciplines is required to develop the knowledge necessary to overcome the challenges of incorporating more renewable forest resources in materials, chemicals, and fuels. We focus on wood specifically because in our view, better characterization of wood as a raw material and as a feedstock will lead to its increased utilization. We first give an overview of wood structure and chemical composition and then highlight current topics in forest products research, including (1) industrial chemicals, biofuels, and energy from woody materials; (2) wood-basedmore » activated carbon and carbon nanostructures; (3) development of improved wood protection treatments; (4) massive timber construction; (5) wood as a bioinspiring material; and (6) atomic simulations of wood polymers. We conclude with a discussion of the sustainability of wood as a renewable forest resource.« less

Not Just Lumber—Using Wood in the Sustainable Future of Materials, Chemicals, and Fuels

NASA Astrophysics Data System (ADS)

Jakes, Joseph E.; Arzola, Xavier; Bergman, Rick; Ciesielski, Peter; Hunt, Christopher G.; Rahbar, Nima; Tshabalala, Mandla; Wiedenhoeft, Alex C.; Zelinka, Samuel L.

2016-09-01

Forest-derived biomaterials can play an integral role in a sustainable and renewable future. Research across a range of disciplines is required to develop the knowledge necessary to overcome the challenges of incorporating more renewable forest resources in materials, chemicals, and fuels. We focus on wood specifically because in our view, better characterization of wood as a raw material and as a feedstock will lead to its increased utilization. We first give an overview of wood structure and chemical composition and then highlight current topics in forest products research, including (1) industrial chemicals, biofuels, and energy from woody materials; (2) wood-based activated carbon and carbon nanostructures; (3) development of improved wood protection treatments; (4) massive timber construction; (5) wood as a bioinspiring material; and (6) atomic simulations of wood polymers. We conclude with a discussion of the sustainability of wood as a renewable forest resource.

Preliminary study on flakeboard panels made from aspen slash wood

Treesearch

Yan Yu; Alan Rudie; Zhiyong Cai

2010-01-01

The disposal of forest-thinning residue is one of the major problems for sustainable forest management. The purpose of this study was to investigate the technical possibility of utilizing aspen logging slash wood with a diameter ranging from 50 to 76 mm for flakeboard production. Influences of weight ratio between slash wood and commercial flakes on the selected...

Nondestructive evaluation of hardwood logs:CT scanning, machine vision and data utilization

Treesearch

Daniel L. Schmoldt; Luis G. Occena; A. Lynn Abbott; Nand K. Gupta

1999-01-01

Sawing of hardwood logs still relies on relatively simple technologies that, in spite of their lack of sophistication, have been successful for many years due to wood?s traditional low cost and ready availability. These characteristics of the hardwood resource have changed dramatically over the past 20 years, however, forcing wood processors to become more efficient in...

Hardwoods in U.S. wood pallet production

Treesearch

Robert J. Bush; Philip A. Araman; E. Bradley Hager

2011-01-01

Research indicates that in 2006, 7.26 billion board feet (approximately 17.1 million m3) of new solid wood was utilized by the U.S. wood pallet and container manufacturing industry. During the same year, the study estimates that 5.09 billion board feet (approximately 12.0 million m3) were recovered mostly from used pallets for reuse and recycling. This paper reports...

Recovery, reuse and recycling by the United States wood packaging industry: 1993-2006

Treesearch

Robert J. Bush; Philip A. Araman; E. Bradley Hager

2007-01-01

The packaging industry is an important market for wood materials, especially low grade hardwoods. Approximately one-third of U.S. hardwood lumber production is utilized in the production of pallets and containers. The industry recovers significant volumes of pallets and containers from the waste stream for re-use, repair, and recycling. Industry by-products (both wood...

Definitive studies on pole-top resuscitation. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon, A.S.; Ridolpho, P.F.; Cole, J.E.

1983-02-01

This report summarizes the history of the application of cardiopulmonary resuscitation to the electric shock victim located at the top of a utility pole. This dramatic and urgent situation requires that rescue be attempted with procedures which are thoroughly understood and effective. Questions related to the use of resuscitation and precordial thump at the pole top were subjected to experimental testing, both in animals and in humans. Results of this study clearly demonstrate the advantages of postponing resuscitation until the victim has been lowered to the ground. The author concludes with seven recommendations for emergency treatment at the scene.

Challenges of Rover Navigation at the Lunar Poles

NASA Technical Reports Server (NTRS)

Nefian, Ara; Deans, Matt; Bouyssounouse, Xavier; Edwards, Larry; Dille, Michael; Fong, Terry; Colaprete, Tony; Miller, Scott; Vaughan, Ryan; Andrews, Dan;

Ohio roundwood utilization by the timber industry in 2006

Treesearch

Jan Wiedenbeck; Andy Sabula

2008-01-01

To identify changes in the structure, size, and wood raw material inputs of the primary wood processing industry in Ohio, the Ohio Division of Forestry and the U.S. Forest Service conduct a periodic survey of this sector. The current assessment of the state of the primary wood products industry in Ohio is based on information collected for the period 2003 through 2006...

25 CFR 700.105 - Utility charges.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Policies and Instructions Definitions § 700.105 Utility charges. Utility charges means the cost for heat, lighting, hot water, electricity, natural gas, butane, propane, wood, coal or other fuels water, sewer and...

Microscopic characterization of tension wood cell walls of Japanese beech (Fagus crenata) treated with ionic liquids.

PubMed

Kanbayashi, Toru; Miyafuji, Hisashi

2016-09-01

Tension wood that is an abnormal part formed in angiosperms has been barely used for wood industry. In this study, to utilize the tension wood effectively by means of liquefaction using ionic liquid, we performed morphological and topochemical determination of the changes in tension wood of Japanese beech (Fagus crenata) during ionic liquid treatment at the cellular level using light microscopy, scanning electron microscopy and confocal Raman microscopy. Ionic liquid treatment induced cell wall swelling in tension wood. Changes in the tissue morphology treated with ionic liquids were different between normal wood and tension wood, moreover the types of ionic liquids. The ionic liquid 1-ethyl-3-methylimidazolium chloride liquefied gelatinous layers rapidly, whereas 1-ethylpyridinium bromide liquefied slowly but delignified selectively. These novel insights into the deconstruction behavior of tension wood cell walls during ionic liquid treatment provide better understanding of the liquefaction mechanism. The obtained knowledge will contribute to development of an effective chemical processing of tension wood using ionic liquids and lead to efficient use of wood resources. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of timber utilization between a tree-length and an in-wood chipping harvesting operations

Treesearch

Suraj Prasad Shrestha; Bobby L. Lanford

2002-01-01

Two 25-year old pine plantations in Alabama, one for in-wood-chipping (IWC) and another for tree length (TL) harvesting operations, were selected to determine the proportion of the standing merchantable timber resource and value that got to a manufacturing facility. Amount of sawtimber after merchandizing in the woods was found to be 80.6 percent of inside bark volume...

Life cycle impacts of forest management and wood utilization on carbon mitigation : knowns and unknowns

Treesearch

Bruce Lippke; Elaine Oneil; Rob Harrison; Kenneth Skog; Leif Gustavsson; Roger Sathre

2011-01-01

This review on research on life cycle carbon accounting examines the complexities in accounting for carbon emissions given the many different ways that wood is used. Recent objectives to increase the use of renewable fuels have raised policy questions, with respect to the sustainability of managing our forests as well as the impacts of how best to use wood from our...

20. Raw Material for the Geographic Magazine. The mills of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. Raw Material for the Geographic Magazine. The mills of the Champion International Company which make paper on which the National Geographic Magazine is printed are located in Lawrence, Mass. This picture shows great piles of pulp-wood ready for conversion into paper for the The Geographic. Parts of these wood piles are more than 50 feet high. The cars shown in the picture are on a trestle 21 feet high. The Geographic magazines mailed in a single year, if laid side by side, would reach from Quito, Ecuador, across Colombia and Caribbean, thence across the United States and Canada, through the North Pole, and across Siberia, China, and Siam to Bangkok. It takes 33,000 miles of wrappers to mail one year's edition. It would require a bookshelf more than three and a half miles long to hold all the copies of this month's issue of The Geographic. (p.235.) - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

Second-order non-linear optical studies on CdS microcrystallite-doped alkali borosilicate glasses

NASA Astrophysics Data System (ADS)

Liu, Hao; Liu, Qiming; Wang, Mingliang; Zhao, Xiujian

2007-05-01

CdS microcrystal-doped alkali borosilicate glasses were prepared by conventional fusion and heat-treatment method. Utilizing Maker fringe method, second-harmonic generation (SHG) was both observed from CdS-doped glasses before and after certain thermal/electrical poling. While because the direction of polarization axes of CdS crystals formed in the samples is random or insufficient interferences of generated SH waves occur, the fringe patterns obtained in samples without poling treatments showed no fine structures. For the poled samples, larger SH intensity has been obtained than that of the samples without any poling treatments. It was considered that the increase of an amount of hexagonal CdS in the anode surface layer caused by the applied dc field increased the SH intensity. The second-order non-linearity χ(2) was estimated to be 1.23 pm/V for the sample poled with 2.5 kV at 360 °C for 30 min.

A methodology to determine the elastic moduli of crystals by matching experimental and simulated lattice strain pole figures using discrete harmonics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wielewski, Euan; Boyce, Donald E.; Park, Jun-Sang

Determining reliable single crystal material parameters for complex polycrystalline materials is a significant challenge for the materials community. In this work, a novel methodology for determining those parameters is outlined and successfully applied to the titanium alloy, Ti-6Al-4V. Utilizing the results from a lattice strain pole figure experiment conducted at the Cornell High Energy Synchrotron Source, an iterative approach is used to optimize the single crystal elastic moduli by comparing experimental and simulated lattice strain pole figures at discrete load steps during a uniaxial tensile test. Due to the large number of unique measurements taken during the experiments, comparisons weremore » made by using the discrete spherical harmonic modes of both the experimental and simulated lattice strain pole figures, allowing the complete pole figures to be used to determine the single crystal elastic moduli. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.« less

Bio-based wood adhesives--preparation, characterization, and testing

USDA-ARS?s Scientific Manuscript database

Adhesive bonding plays an increasing role in the forest product industry and is a key factor for efficiently utilizing timber and other lignocellulosic resources. As synthetic wood adhesives are mostly derived from depleting petrochemical resources and have resulted in increasing environmental conce...

UTILIZING LOW VOLATILE ORGANIC CONTENT EXTERIOR COATINGS FOR WOOD FURNITURE

EPA Science Inventory

This report provides an evaluation of commercially viable source reduction techniques implemented by a manufacturer of wood chairs, bar stools and settees in various styles ranging from classic American to European contemporary. As federal EPA regulations became more stringent fo...

Thermal exploitation of wastes with lignite for energy production.

PubMed

Grammelis, Panagiotis; Kakaras, Emmanuel; Skodras, George

2003-11-01

The thermal exploitation of wastewood with Greek lignite was investigated by performing tests in a laboratory-scale fluidized bed reactor, a 1-MW(th) semi-industrial circulating fluidized bed combustor, and an industrial boiler. Blends of natural wood, demolition wood, railroad sleepers, medium-density fiberboard residues, and power poles with lignite were used, and the co-combustion efficiency and the effect of wastewood addition on the emitted pollutants were investigated. Carbon monoxide, sulfur dioxide, and oxides of nitrogen emissions were continuously monitored, and, during the industrial-scale tests, the toxic emissions (polychlorinated dibenzodioxins and dibenzofurans and heavy metals) were determined. Ash samples were analyzed for heavy metals in an inductively coupled plasma-atomic emission spectroscopy spectrophotometer. Problems were observed during the preparation of wastewood, because species embedded with different compounds, such as railway sleepers and demolition wood, were not easily treated. All wastewood blends were proven good fuels; co-combustion proceeded smoothly and homogeneous temperature and pressure profiles were obtained. Although some fluctuations were observed, low emissions of gaseous pollutants were obtained for all fuel blends. The metal element emissions (in the flue gases and the solid residues) were lower than the legislative limits. Therefore, wastewood co-combustion with lignite can be realized, provided that the fuel handling and preparation can be practically performed in large-scale installations.

Time-scale dynamics of proteome and transcriptome of the white-rot fungus Phlebia radiata: growth on spruce wood and decay effect on lignocellulose.

PubMed

Kuuskeri, Jaana; Häkkinen, Mari; Laine, Pia; Smolander, Olli-Pekka; Tamene, Fitsum; Miettinen, Sini; Nousiainen, Paula; Kemell, Marianna; Auvinen, Petri; Lundell, Taina

2016-01-01

The white-rot Agaricomycetes species Phlebia radiata is an efficient wood-decaying fungus degrading all wood components, including cellulose, hemicellulose, and lignin. We cultivated P. radiata in solid state cultures on spruce wood, and extended the experiment to 6 weeks to gain more knowledge on the time-scale dynamics of protein expression upon growth and wood decay. Total proteome and transcriptome of P. radiata were analyzed by peptide LC-MS/MS and RNA sequencing at specific time points to study the enzymatic machinery on the fungus' natural growth substrate. According to proteomics analyses, several CAZy oxidoreductase class-II peroxidases with glyoxal and alcohol oxidases were the most abundant proteins produced on wood together with enzymes important for cellulose utilization, such as GH7 and GH6 cellobiohydrolases. Transcriptome additionally displayed expression of multiple AA9 lytic polysaccharide monooxygenases indicative of oxidative cleavage of wood carbohydrate polymers. Large differences were observed for individual protein quantities at specific time points, with a tendency of enhanced production of specific peroxidases on the first 2 weeks of growth on wood. Among the 10 class-II peroxidases, new MnP1-long, characterized MnP2-long and LiP3 were produced in high protein abundances, while LiP2 and LiP1 were upregulated at highest level as transcripts on wood together with the oxidases and one acetyl xylan esterase, implying their necessity as primary enzymes to function against coniferous wood lignin to gain carbohydrate accessibility and fungal growth. Majority of the CAZy encoding transcripts upregulated on spruce wood represented activities against plant cell wall and were identified in the proteome, comprising main activities of white-rot decay. Our data indicate significant changes in carbohydrate-active enzyme expression during the six-week surveillance of P. radiata growing on wood. Response to wood substrate is seen already during the first weeks. The immediate oxidative enzyme action on lignin and wood cell walls is supported by detected lignin substructure sidechain cleavages, release of phenolic units, and visual changes in xylem cell wall ultrastructure. This study contributes to increasing knowledge on fungal genetics and lignocellulose bioconversion pathways, allowing us to head for systems biology, development of biofuel production, and industrial applications on plant biomass utilizing wood-decay fungi.

Analysis of polyethylene terephthalate PET plastic bottle jointing system using finite element method (FEM)

NASA Astrophysics Data System (ADS)

Zaidi, N. A.; Rosli, Muhamad Farizuan; Effendi, M. S. M.; Abdullah, Mohamad Hariri

2017-09-01

For almost all injection molding applications of Polyethylene Terephthalate (PET) plastic was analyzed the strength, durability and stiffness of properties by using Finite Element Method (FEM) for jointing system of wood furniture. The FEM was utilized for analyzing the PET jointing system for Oak and Pine as wood based material of furniture. The difference pattern design of PET as wood jointing furniture gives the difference value of strength furniture itself. The results show the wood specimen with grooves and eclipse pattern design PET jointing give lower global estimated error is 28.90%, compare to the rectangular and non-grooves wood specimen of global estimated error is 63.21%.

Fault Tolerant Homopolar Magnetic Bearings

NASA Technical Reports Server (NTRS)

Li, Ming-Hsiu; Palazzolo, Alan; Kenny, Andrew; Provenza, Andrew; Beach, Raymond; Kascak, Albert

2003-01-01

Magnetic suspensions (MS) satisfy the long life and low loss conditions demanded by satellite and ISS based flywheels used for Energy Storage and Attitude Control (ACESE) service. This paper summarizes the development of a novel MS that improves reliability via fault tolerant operation. Specifically, flux coupling between poles of a homopolar magnetic bearing is shown to deliver desired forces even after termination of coil currents to a subset of failed poles . Linear, coordinate decoupled force-voltage relations are also maintained before and after failure by bias linearization. Current distribution matrices (CDM) which adjust the currents and fluxes following a pole set failure are determined for many faulted pole combinations. The CDM s and the system responses are obtained utilizing 1D magnetic circuit models with fringe and leakage factors derived from detailed, 3D, finite element field models. Reliability results are presented vs. detection/correction delay time and individual power amplifier reliability for 4, 6, and 7 pole configurations. Reliability is shown for two success criteria, i.e. (a) no catcher bearing contact following pole failures and (b) re-levitation off of the catcher bearings following pole failures. An advantage of the method presented over other redundant operation approaches is a significantly reduced requirement for backup hardware such as additional actuators or power amplifiers.

Bibliography of FPL tropical forest utilization research–1910 to 1989

Treesearch

R. Sidney Boone; Lee R. Gjovik; George B. Harpole; James F. Laundrie; Robert R. Maeglin; Ronald W. Wolfe

1990-01-01

A complete annotated bibliography of all published and unpublished reports of the USDA Forest Service, Forest Products Laboratory, on the subject of tropical woods. Research on tropical woods began soon after the formation of the Forest Products Laboratory in 1910 and continues today.

Overview of IEA biomass combustion activities

NASA Astrophysics Data System (ADS)

Hustad, J. E.

1994-07-01

The objectives of the International Energy Agency (IEA) bioenergy program are: (1) to encourage cooperative research, development and use of energy and the increased utilization of alternatives to oil; and (2) to establish increased program and project cooperation between participants in the whole field of bioenergy. There are four Task Annexes to the Implementing Agreement during the period 1992-1994: Efficient and Environmentally Sound Biomass Production Systems; Harvesting and Supply of Woody Biomass for Energy; Biomass Utilization; and Conversion of Municipal Solid Waste Feedstock to Energy. The report describes the following biomass combustion activities during the period 1992-1994: Round robin test of a wood stove; Emissions from biomass combustion; A pilot project cofiring biomass with oil to reduce SO2 emissions; Small scale biomass chip handling; Energy from contaminated wood waste combustion; Modeling of biomass combustion; Wood chip cogeneration; Combustion of wet biomass feedstocks, ash reinjection and carbon burnout; Oxidation of wet biomass; Catalytic combustion in small wood burning appliances; Characterization of biomass fuels and ashes; Measurement techniques (FTIR).

Solvent cleaning of pole transformers containing PCB contaminated insulating oil.

PubMed

Kanbe, H; Shibuya, M

2001-01-01

In 1989, it was discovered that the recycled insulation oil in pole transformers for electric power supply was contaminated with trace amounts of polychlorinated biphenyls (PCBs; maximum 50 mg-PCB/kg-insulation oil). In order to remove the PCBs from transformer components using n-hexane as a solvent, we investigated the relationship between progressive stages of dismantling and cleaning results. The results are summarized as follows: (1) Based on the cleaning test results, we made an estimate of the residual PCB amount on iron and copper components. By dismantling the test pole transformers into the "iron core and coil portion" and cleaning the components, we achieved a residual PCB amount that was below the limit of detection (0.05 mg-PCB/kg-material). To achieve a residual PCB amount below the limit of detection for the transformer paper component, it was necessary to cut the paper into pieces smaller than 5 mm. We were unable to achieve a residual PCB amount below the limit of detection for the wood component. (2) Compared to Japan's stipulated limited concentration standard values for PCBs, the results of the cleaning test show that cleaning iron or copper components with PCBs only on their surface with the solvent n-hexane will satisfy the limited concentration standard values when care is taken to ensure the component surfaces have adequate contact with the cleaning solvent.

75 FR 45494 - Implementation of Section 224 of the Act; a National Broadband Plan for Our Future

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

... attachers make informed decisions and should facilitate the attachment process. If a utility denies an... forward, and whether utilities' decisions regarding the use of boxing and bracketing should also be made... nondiscriminatory access to any pole, duct, conduit, or right-of-way owned or controlled by a utility. However, the...

Utilization of porous carbons derived from coconut shell and wood in natural rubber

USDA-ARS?s Scientific Manuscript database

The porous carbons derived from cellulose are renewable and environmentally friendly. Coconut shell and wood derived porous carbons were characterized with elemental analysis, ash content, x-ray diffraction, infrared absorbance, particle size, surface area, and pore volume. The results were compared...

Department of the Navy. FY 1994/FY 1995 Biennial Budget Estimates. Military Construction Program. FY 1994

DTIC Science & Technology

1992-01-01

3 are severely deteriorated. The concrete deck and supporting wood -pile structure are nearing the end of their life cycle. Both piers are to be...PROPOSED CONSTRUCTION One-story building with concrete foundation walls, load bearing masonry walls, and concrete floors; roof with wood truss framing...concrete building addition; concrete foundation and slab on grade; wood truss roof; 750 KVA. 3 phase transformer; utilities; concrete and storm drain. 11

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Oisik; Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz; Bhattacharyya, Debes

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted bymore » manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications.« less

Performance Analysis of a Pole and Tree Trunk Detection Method for Mobile Laser Scanning Data

NASA Astrophysics Data System (ADS)

Lehtomäki, M.; Jaakkola, A.; Hyyppä, J.; Kukko, A.; Kaartinen, H.

2011-09-01

Dense point clouds can be collected efficiently from large areas using mobile laser scanning (MLS) technology. Accurate MLS data can be used for detailed 3D modelling of the road surface and objects around it. The 3D models can be utilised, for example, in street planning and maintenance and noise modelling. Utility poles, traffic signs, and lamp posts can be considered an important part of road infrastructure. Poles and trees stand out from the environment and should be included in realistic 3D models. Detection of narrow vertical objects, such as poles and tree trunks, from MLS data was studied. MLS produces huge amounts of data and, therefore, processing methods should be as automatic as possible and for the methods to be practical, the algorithms should run in an acceptable time. The automatic pole detection method tested in this study is based on first finding point clusters that are good candidates for poles and then separating poles and tree trunks from other clusters using features calculated from the clusters and by applying a mask that acts as a model of a pole. The method achieved detection rates of 77.7% and 69.7% in the field tests while 81.0% and 86.5% of the detected targets were correct. Pole-like targets that were surrounded by other objects, such as tree trunks that were inside branches, were the most difficult to detect. Most of the false detections came from wall structures, which could be corrected in further processing.

Acquisition of wood fuel at the Joseph C. McNeil Generating Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kropelin, W.

1993-12-31

The Joseph C. McNeil Generating Station is the world`s largest single boiler, municipally-owned, wood-fired electrical generating plant. The 50 megawatt McNeil Station is located in Burlington, Vermont and is owned by several Vermont public and private electric utilities. The operator and majority owner is the City of Burlington Electric Department (BED). Wood fuel procurement for the McNeil Station has been conducted in an environmentally sensitive way. Harvesting is carried out in conformance with a comprehensive wood chip harvesting policy and monitored by professional foresters. Unpredictable levels of Station operation require rigid adherence to a wood storage plan that minimizes themore » risk of over heating and spontaneous combustion of stockpiled fuel.« less

Woodmetrics: imaging devices and processes in wood inspection at Lulea University of Technology

NASA Astrophysics Data System (ADS)

Hagman, Olle

1999-09-01

Wood Technology research and education at Lulea University of Technology is located in Skelleftea 800 km north of Stockholm. At the campus about 25 persons are involved in education and research in Wood Technology. We are educating M.Sc. and post- graduate students in Wood Technology. The research at the campus includes the following main fields: -- Wood Machining - - Woodmetrics -- Wood Drying -- Wood Composites/Wood Material Science. Our research strategy is to obtain an individual treatment of every tree, board and piece of wood in order to get highest possible value for the forest products. This shall be accomplished by the aid of advanced scanning technology and computer technology. Woodmetrics means to measure different wood parameters in order to optimize the utilization of the raw material. Today we have the following projects in this field: Automatic wood inspection -- Color changes and moisture flow in drying processes -- Inner quality of logs and lumber - - Stem quality database -- Computer tomography -- Aesthetic properties of wood -- Market/industry/forest relations. In the Woodmetrics field we are using computer tomography, CCD cameras and other sensors in order to find and measure defects in trees and on boards. The signals are analyzed and classified with modern image analyzing techniques and advanced statistical methods.

First observation of the Λ(1405) line shape in electroproduction

NASA Astrophysics Data System (ADS)

Lu, H. Y.; Schumacher, R. A.; Adhikari, K. P.; Adikaram, D.; Aghasyan, M.; Amaryan, M. J.; Pereira, S. Anefalos; Ball, J.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A. S.; Boiarinov, S.; Briscoe, W. J.; Brooks, W. K.; Burkert, V. D.; Carman, D. S.; Celentano, A.; Chandavar, S.; Cole, P. L.; Collins, P.; Contalbrigo, M.; Cortes, O.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Deur, A.; Djalali, C.; Doughty, D.; Dupre, R.; Egiyan, H.; Alaoui, A. El; Fassi, L. El; Eugenio, P.; Fedotov, G.; Fegan, S.; Fleming, J. A.; Gabrielyan, M.; Gevorgyan, N.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Goetz, J. T.; Gohn, W.; Golovatch, E.; Gothe, R. W.; Griffioen, K. A.; Guidal, M.; Guo, L.; Hafidi, K.; Hakobyan, H.; Harrison, N.; Heddle, D.; Hicks, K.; Ho, D.; Holtrop, M.; Hyde, C. E.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Isupov, E. L.; Jo, H. S.; Joo, K.; Keller, D.; Khandaker, M.; Kim, W.; Klein, A.; Klein, F. J.; Koirala, S.; Kubarovsky, A.; Kubarovsky, V.; Kuleshov, S. V.; Lewis, S.; Livingston, K.; MacGregor, I. J. D.; Martinez, D.; Mayer, M.; McKinnon, B.; Meyer, C. A.; Mineeva, T.; Mirazita, M.; Mokeev, V.; Montgomery, R. A.; Moriya, K.; Moutarde, H.; Munevar, E.; Camacho, C. Munoz; Nadel-Turonski, P.; Nepali, C. S.; Niccolai, S.; Niculescu, G.; Niculescu, I.; Osipenko, M.; Ostrovidov, A. I.; Pappalardo, L. L.; Paremuzyan, R.; Park, K.; Park, S.; Pasyuk, E.; Peng, P.; Phelps, E.; Phillips, J. J.; Pisano, S.; Pogorelko, O.; Pozdniakov, S.; Price, J. W.; Procureur, S.; Prok, Y.; Protopopescu, D.; Puckett, A. J. R.; Raue, B. A.; Rimal, D.; Ripani, M.; Rosner, G.; Rossi, P.; Sabatié, F.; Saini, M. S.; Salgado, C.; Schott, D.; Seder, E.; Seraydaryan, H.; Sharabian, Y. G.; Smith, G. D.; Sober, D. I.; Sokhan, D.; Stepanyan, S. S.; Stoler, P.; Strauch, S.; Taiuti, M.; Tang, W.; Tian, Ye; Tkachenko, S.; Torayev, B.; Vernarsky, B.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Weygand, D. P.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zhao, Z. W.

2013-10-01

We report the first observation of the line shape of the Λ(1405) from electroproduction, and show that it is not a simple Breit-Wigner resonance. Electroproduction of K+Λ(1405) off the proton was studied by using data from CLAS at Jefferson Lab in the range 1.0

Lunar Prospecting: Searching for Volatiles at the South Pole

NASA Technical Reports Server (NTRS)

Trimble, Jay; Carvalho, Robert

2016-01-01

The Resource Prospector is an in-situ resource utilization (ISRU) technology demonstration mission, planned for a 2021 launch to search for and analyze volatiles at the Lunar South Pole. The mission poses unique operational challenges. Operating at the Lunar South Pole requires navigating a surface with lighting, shadow and regolith characteristics unlike those of previous missions. The short round trip communications time enables reactive surface operations for science and engineering. Navigation of permanently shadowed regions with a solar powered rover creates risks, including power and thermal management, and requires constant real time decision making for safe entry, path selection and egress. The mission plan requires a faster rover egress from the lander than any previous NASA rover mission.

KSC00pp0243

NASA Image and Video Library

2000-02-18

KENNEDY SPACE CENTER, FLA. -- A Southern Bald Eagle perched on top of a utility pole searches the area. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

KSC-00pp0243

NASA Image and Video Library

2000-02-18

KENNEDY SPACE CENTER, FLA. -- A Southern Bald Eagle perched on top of a utility pole searches the area. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insects

KSC00pp0242

NASA Image and Video Library

2000-02-18

KENNEDY SPACE CENTER, FLA. -- A Southern Bald Eagle perches on top of a utility pole at Kennedy Space Center. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insect

KSC-00pp0242

NASA Image and Video Library

2000-02-18

KENNEDY SPACE CENTER, FLA. -- A Southern Bald Eagle perches on top of a utility pole at Kennedy Space Center. About a dozen bald eagles live in the Merritt Island National Wildlife Refuge, which shares a boundary with Kennedy Space Center. The Southern Bald Eagle ranges throughout Florida and along the coasts of California, Texas, Louisiana, and the south Atlantic states. Bald Eagles are listed as endangered in the U.S., except in five states where they are listed as threatened. The number of nesting pairs of the southern race once numbered several thousand; recent estimates are only 350-375. Most of the southern race nest in Florida. Eagles arrive at KSC during late summer and leave for the north in late spring. They move to nest sites in October and November and lay one to three eggs. The young fledge from February to April. The Refuge encompasses 92,000 acres that are a habitat for more than 331 species of birds, 31 mammals, 117 fishes, and 65 amphibians and reptiles. The marshes and open water of the refuge provide wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds, as well as a variety of insect

A pilot study of a portable wood chipper

Treesearch

R. H. Fenton; H. A. McKusick

1950-01-01

A cooperative investigation carried on by the Connecticut State Park and Forest Commission and the Northeastern Forest Experiment Station in collaboration with the Northeastern Wood Utilization Council, Inc., the Fitchburg Engineering Company, the Connecticut Highway Department, and the Connecticut Board of Fisheries and Game. The authors acknowledge the generous...

Interfacial Structure and Properties of Wood/Polypropylene Composites

Treesearch

Timothy G. Rials; Michael P. Wolcott; Suzhow Yin

2000-01-01

Composite wood products have traditionally relied on thermosetting polymers like phenol-formaldehyde and urea-formaldehyde resins as binders. The continuing need to effectively utilize lignocellulosic fiber from low-quality hardwoods and from recycling streams has prompted consideration of new composites based on thermoplastic polymers [1,2]. Much of the development...

Choosing forest residues management alternatives.

Treesearch

John M. Pierovich; Richard C. Smith

1973-01-01

Forest residues management involves disposal, modification, or utilization of wood products. The costs and benefits of the several alternatives available to forest managers must be evaluated in relation to land management goals and constraints in four areas: (1) unused wood fiber, (2) conflagrations, (3) impairment of forest resources, and (4) opposition to treatment...

Characterizing wood-plastic composites via data-driven methodologies

Treesearch

John G. Michopoulos; John C. Hermanson; Robert Badaliance

2007-01-01

The recent increase of wood-plastic composite materials in various application areas has underlined the need for an efficient and robust methodology to characterize their nonlinear anisotropic constitutive behavior. In addition, the multiplicity of various loading conditions in structures utilizing these materials further increases the need for a characterization...

Engineered and Other Wood Products - An Opportunity to "Grow the Pie"

Treesearch

Albert Schuler; Craig Adair

2003-01-01

The market for engineered wood products (EWP) is being driven by a number of factors including: technology; reduced availability of old-growth timber; construction activity, and globalization. Specifically, technological developments have allowed the industry to "engineer" or "design" improved performance properties and to utilize former "weed...

Chunkwood: Production, characterization, and utilization.

Treesearch

Rodger A. Arola

1991-01-01

Presents a collection of U.S. research papers about chunkwood, an alternative form of comminuted wood particles that range from finger size up to fairly large, blocky particles of wood. Discusses chunkwood`s characteristics, storage and drying, machinery, and use to build low-volume roads and as furnish for composite flake products.

Resource Prospector: Evaluating the ISRU Potential of the Lunar Poles

NASA Technical Reports Server (NTRS)

Colaprete, A.; Elphic, R.; Andrews, D.; Trimble, J.; Bluethmann, B.; Quinn, J.; Chavers, G.

2017-01-01

Resource Prospector (RP) is a lunar volatiles prospecting mission being developed for potential flight in CY2021-2022. The mission includes a rover-borne payload that (1) can locate surface and near-subsurface volatiles, (2) excavate and analyze samples of the volatile-bearing regolith, and (3) demonstrate the form, extractability and usefulness of the materials. The primary mission goal for RP is to evaluate the In-Situ Resource Utilization (ISRU) potential of the lunar poles.

76 FR 26620 - A National Broadband Plan for Our Future

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-09

... communications space on utility poles. For wireless attachments above the communications space, we adopt a...-authorized by the utilities to complete survey and make-ready work in the communications space, subject to a... and wireless attachments either in or above the communications space. This required response is...

Mitigating environmental impacts through the energetic use of wood: Regional displacement factors generated by means of substituting non-wood heating systems.

PubMed

Wolf, Christian; Klein, Daniel; Richter, Klaus; Weber-Blaschke, Gabriele

2016-11-01

Wood biomass, especially when applied for heating, plays an important role for mitigating environmental impacts such as climate change and the transition towards higher shares of renewable energy in today's energy mix. However, the magnitude of mitigation benefits and burdens associated with wood use can vary greatly depending on regional parameters such as the displaced fossil reference or heating mix. Therefore, regionalized displacement factors, considering region-specific production conditions and substituted products are required when assessing the precise contribution of wood biomass towards the mitigation of environmental impacts. We carried out Life Cycle Assessments of wood heating systems for typical Bavarian conditions and substitute energy carriers with a focus on climate change and particulate matter emissions. In order to showcase regional effects, we created weighted displacement factors for the region of Bavaria, based on installed capacities of individual wood heating systems and the harvested tree species distribution. The study reveals that GHG displacements between -57gCO2-eq.∗MJ(-1) of useful energy through the substitution of natural gas with a 15kW spruce pellets heating system and -165gCO2-eq.∗MJ(-1) through the substitution of power utilized for heating with a modern 6kW beech split log heating system can be achieved. It was shown that the GHG mitigation potentials of wood utilization are overestimated through the common use of light fuel oil as the only reference system. We further propose a methodology for the calculation of displacement factors which is adaptable to other regions worldwide. Based on our approach it is possible to generate displacement factors for wood heating systems which enable accurate decision-making for project planning in households, heating plants, communities and also for entire regions. Copyright © 2016 Elsevier B.V. All rights reserved.

Analysis of the costs of fuel supply for wood-fired electric power plants in rural Liberia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perlack, R.D.; Barron, W.F.; Samuels, G.

1985-06-01

In recent years the quality of rural electric services in Liberia has been declining and the future economic viability of these power stations is a growing concern. Each of the ten operating and each of the planned rural public power stations is designed to operate exclusively on gas oil (diesel fuel). Fuel expenditures by the Liberian Electricity Corporation (LEC) for the rural public stations represent a major and growing burden on the financially hardpressed utility. Liberia has two potentially significant alternatives to oil-fired electric power for its up-country towns: small (1 to 5 MW) hydroelectric facilities, and wood-fired steam ormore » gasifier plants (0.2 to 2 MW). Although small hydroelectric facilities appear viable for several locations, they cannot serve all locations and will require thermal back-up. The economics of supplying wood to a rural electric power plant or rural grid were evaluated under several scenarios involving: (1) different sources of the feedstock, and (2) differences in wood supply requirements for plants based on the use of steam or gasifier technology, and variation in the utilization level for such plants. With a few minor exceptions, wood energy supplies are plentiful throughout Liberia. Liberia has four different potential sources of wood fuel supply: the commercial cutting of retired rubber trees; the harvesting of secondary growth forest just prior to the land returning to temporary cultivation as part of a system of shifting agriculture; adding to the system of shifting agriculture the planting of fast-growing wood species and harvesting these trees when the land again is brought back under cultivation (generally after about five to seven years); and the establishment of commercial short-rotation wood energy plantations. Results indicate that the use of wood to fuel rural power stations is a viable economic option.« less

KSC-07pd0150

NASA Image and Video Library

2007-01-19

KENNEDY SPACE CENTER, FLA. -- This young red-shouldered hawk perches on a roadside pole inside NASA's Kennedy Space Center. The habitat of these hawks is deciduous woodlands, especially near standing water, frequently found in lowlands such as swampy woods and bogs. They range throughout the eastern half of the United States. KSC shares a boundary with the Merritt Island Wildlife Nature Refuge. The refuge is a habitat for more than 310 species of birds, 25 mammals, 117 fishes and 65 amphibians and reptiles. In addition, the Refuge supports 19 endangered or threatened wildlife species on Federal or State lists, more than any other single refuge in the U.S. Photo credit: NASA/Ken Thornsley

Economic summary of woody biomass direct combustion and gasification alternatives

NASA Astrophysics Data System (ADS)

1981-08-01

A base case analysis indicates that acceptable rates of return on investment are possible when utilizing wood as a commercial scale boiler fuel. Principal variables include the availability of cost competitive wood fuel over the term of the loan and overall installed cost for the system. In some cases the cost of coal at the point of end use will be comparable with wood. Hardware costs will determine system economics and applicable air quality standards, or lack thereof, will play an important role. The overall economics of using wood for fuel are extremely site specific. The additional 10 percent energy tax credit greatly enhances the economics of a wood fired system, although system economics are very attractive without this tax incentive. Cost of money does not seem to drastically affect overall system economics.

Stormwater filtration of a municipal detention pond

Treesearch

James S. Han; Ernest S. Miyashita; Yi-yu Lin; Alcardo Roa

1999-01-01

Wood- and nonwood-based fibers have been found to have a significant sorption capacity for ionized copper, a heavy metal commonly found in stormwater. The USDA-FS Forest Products Laboratory (Madison, WI) is conducting research on the potential of utilizing natural wood- and nonwood-based fibers in stormwater treatment. The problem with the current practice of...

Adhesive properties of water washed cottonseed meal on poplar, douglas fir, walnut, and white oak

USDA-ARS?s Scientific Manuscript database

The interest in natural product-based wood adhesives has been steadily increasing due to the environmental and sustainable concerns of petroleum-based adhesives. In this work, we reported our research on utilization of water washed cottonseed meal (WCM) as wood adhesives. The adhesive strength and w...

Advancing sustainable forestry by using engineered wood or bio-composites

Treesearch

Jerrold E. Winandy

2005-01-01

As worldwide demand for timber and bio-fiber resources grows, sustainable resource management and industrial utilization must collaborate to develop a shared vision for both long-term sustainable management of forest and bio-resources and sustainable economic development. Engineered wood- and bio-composites offer a tool that can both achieve resource sustainability and...

Using Eucalypts in manufacturing

Treesearch

William A. Dost

1983-01-01

Eucalypts have a number of characteristics affecting processing and utilization that distinguish them from other woods. The major current interest in the eucalypts is as a fuel. Possible demand as a chemical feedstock, for pulp-wood, panel products, lumber or round timbers should be considered in initial planning and management as a hedge against changes resulting from...

A study of logging residue at woods landings in Appalachia

Treesearch

Curtis D. Goho

1976-01-01

A study of residue on five woods landings in West Virginia showed that short lengths, poor quality, and low volumes are obstacles to utilization of this material. Short lengths and dirt accumulation would also pose serious problems for conversion to chips. Some local use for firewood and specialty products is possible.

Summary of U.S. research on wood transportation structures

Treesearch

M. A. Ritter; R. C. Moody; S. R. Duwadi

1996-01-01

An extensive U.S. research program to further develop wood utilization in transportation structures is currently in progress as a joint effort of the USDA Forest Service, Forest Products Laboratory, and the U.S. Department of Transportation, Federal Highway Administration. This research is funded primarily by U.S. legislation and involves cooperative research with...

The application of nirvana to silvicultural studies

Treesearch

Chi-Leung So; Thomas Elder; Leslie Groom; John S. Kush; Jennifer Myszewski; Todd Shupe

2006-01-01

Previous results from this laboratory have shown that near infrared (NIR) spectroscopy, coupled with multivariate analysis, can be a powerful tool for the prediction of wood quality. While wood quality measurements are of utility, their determination can be both time and labor intensive, thus limiting their use where large sample sizes are concerned. This paper will...

Research on key factors and their interaction effects of electromagnetic force of high-speed solenoid valve.

PubMed

Liu, Peng; Fan, Liyun; Hayat, Qaisar; Xu, De; Ma, Xiuzhen; Song, Enzhe

2014-01-01

Analysis consisting of numerical simulations along with lab experiments of interaction effects between key parameters on the electromagnetic force based on response surface methodology (RSM) has been also proposed to optimize the design of high-speed solenoid valve (HSV) and improve its performance. Numerical simulation model of HSV has been developed in Ansoft Maxwell environment and its accuracy has been validated through lab experiments. Effect of change of core structure, coil structure, armature structure, working air gap, and drive current on the electromagnetic force of HSV has been analyzed through simulation model and influence rules of various parameters on the electromagnetic force have been established. The response surface model of the electromagnetic force has been utilized to analyze the interaction effect between major parameters. It has been concluded that six interaction factors including working air gap with armature radius, drive current with armature thickness, coil turns with side pole radius, armature thickness with its radius, armature thickness with side pole radius, and armature radius with side pole radius have significant influence on the electromagnetic force. Optimal match values between coil turns and side pole radius; armature thickness and side pole radius; and armature radius and side pole radius have also been determined.

Research on Key Factors and Their Interaction Effects of Electromagnetic Force of High-Speed Solenoid Valve

PubMed Central

Fan, Liyun; Xu, De; Ma, Xiuzhen; Song, Enzhe

2014-01-01

Analysis consisting of numerical simulations along with lab experiments of interaction effects between key parameters on the electromagnetic force based on response surface methodology (RSM) has been also proposed to optimize the design of high-speed solenoid valve (HSV) and improve its performance. Numerical simulation model of HSV has been developed in Ansoft Maxwell environment and its accuracy has been validated through lab experiments. Effect of change of core structure, coil structure, armature structure, working air gap, and drive current on the electromagnetic force of HSV has been analyzed through simulation model and influence rules of various parameters on the electromagnetic force have been established. The response surface model of the electromagnetic force has been utilized to analyze the interaction effect between major parameters. It has been concluded that six interaction factors including working air gap with armature radius, drive current with armature thickness, coil turns with side pole radius, armature thickness with its radius, armature thickness with side pole radius, and armature radius with side pole radius have significant influence on the electromagnetic force. Optimal match values between coil turns and side pole radius; armature thickness and side pole radius; and armature radius and side pole radius have also been determined. PMID:25243217

Cambium

NASA Technical Reports Server (NTRS)

Savidge, Rodney

2009-01-01

The Cambium investigation is one in a pair of investigations which utilizes the Advanced Biological Research System (ABRS). Cambium seeks definitive evidence that gravity has a direct effect on cambial cells (cells located under the inner bark where secondary growth occurs) in willow, Salix babylonica. The Cambium investigation uses willow plants flown on the International Space Station to better understand the fundamental processes by which plants produce cellulose and lignin, the two main structural materials found in plant matter. On Earth, the nature of wood within tree stems varies depending on position, and that within-tree variation includes differences in cell types and chemistry including lignin and cellulose, two major components of wood influencing wood strength, usefulness and carbon content. Reaction wood is an extreme example of such variation, and it is believed that reaction wood develops as a reaction to the influence of gravity. For the Cambium experiment, young willow plants will be launched to the ISS where their stems will be looped in an attempt to induce reaction wood formation. After on-orbit growth, the plants will be preserved and returned to Earth for analysis. Understanding the role of gravity in wood formation is expected to enable wiser management of forests for carbon sequestration as well as better utilization of trees for wood products. Detailed Research Description: The Cambium experiment will provide an understanding of physiological processes such as gene expression, metabolism and general plant development that are affected in plant systems exposed to space flight. Cambium seeks definitive evidence that gravity has a direct effect on the cambial cells (cells located under the inner bark where secondary growth occurs) that contribute to xylogenesis (reaction wood formation) in willow plants, Salix babylonica. Tension wood fibers differentiate on the upper sides of stems when the stem is altered from its normal (vertical) growth position by looping. This reaction wood response does not occur if the orientation of the plant stem with respect to gravity is not altered. If a localized zone of tension wood should be formed in looped stems under microgravity conditions, this would be the first conclusive evidence that gravity is not required. On the other hand, if a zone of tension wood is not produced in looped stems (subjected to tension on one side, compression on the other) in microgravity, this would be the first definitive evidence that gravity has a direct effect on the cambial cells which contribute to reaction wood formation. Following return to Earth the plants will be analyzed by microscopy and chemical methods.

How Deep-Sea Wood Falls Sustain Chemosynthetic Life

PubMed Central

Bienhold, Christina; Pop Ristova, Petra; Wenzhöfer, Frank; Dittmar, Thorsten; Boetius, Antje

2013-01-01

Large organic food falls to the deep sea – such as whale carcasses and wood logs – are known to serve as stepping stones for the dispersal of highly adapted chemosynthetic organisms inhabiting hot vents and cold seeps. Here we investigated the biogeochemical and microbiological processes leading to the development of sulfidic niches by deploying wood colonization experiments at a depth of 1690 m in the Eastern Mediterranean for one year. Wood-boring bivalves of the genus Xylophaga played a key role in the degradation of the wood logs, facilitating the development of anoxic zones and anaerobic microbial processes such as sulfate reduction. Fauna and bacteria associated with the wood included types reported from other deep-sea habitats including chemosynthetic ecosystems, confirming the potential role of large organic food falls as biodiversity hot spots and stepping stones for vent and seep communities. Specific bacterial communities developed on and around the wood falls within one year and were distinct from freshly submerged wood and background sediments. These included sulfate-reducing and cellulolytic bacterial taxa, which are likely to play an important role in the utilization of wood by chemosynthetic life and other deep-sea animals. PMID:23301092

A Scapholunate Ligament-Sparing Technique Utilizing the Medial Femoral Condyle Corticocancellous Free Flap to Reconstruct Scaphoid Nonunions With Proximal Pole Avascular Necrosis.

PubMed

Kazmers, Nikolas H; Thibaudeau, Stephanie; Levin, L Scott

2016-09-01

This article demonstrates a technique for the treatment of scaphoid fracture waist and proximal pole nonunions with avascular necrosis using a free vascularized medial femoral condyle flap. We present our surgical technique and representative case examples in which the scapholunate ligament, a key structure required to preserve carpal kinematics, is spared. Copyright © 2016 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Polarization Utilization in Radar Target Reconstruction: C-Wide (Multi-Frequency) Band Relationship of a Target’s Characteristic Operators with Its Unique Set of Natural Eigenfrequencies.

DTIC Science & Technology

1983-12-14

the left half of the s- plane . These are representation independent. We shall be interested in these poles only. These poles are the complex...on the Left Half Plane Asymptotic Behavior of the SEM Expansion of Surface Currents, Published in Special Issue on the Singularity Expansion Method...precisely, the polarization chart is an orthogonal projection of the Poincare Sphere on a plane , having polar coordinates p= cos (2-) and

Stress wave nondestructive evaluation of Douglas-fir peeler cores

Treesearch

Robert J. Ross; John I. Zerbe; Xiping Wang; David W. Green; Roy F. Pellerin

2005-01-01

With the need for evaluating the utilization of veneer peeler log cores in higher value products and the increasing importance of utilizing round timbers in poles, posts, stakes, and building construction components, we conducted a cooperative project to verify the suitability of stress wave nondestructive evaluation techniques for assessing peeler cores and some...

47 CFR 1.1402 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Procedures § 1.1402 Definitions. (a) The term utility means any person that is a local exchange carrier or an electric, gas, water, steam, or other public utility, and who owns or controls poles, ducts, conduits, or... telecommunications services (as defined in 47 U.S.C. 226) or incumbent local exchange carriers (as defined in 47 U.S...

The role of forests in energy and climate change - integrating objectives

Treesearch

Dave Atkins

2010-01-01

Woody biomass utilization presents a tremendous opportunity to address energy independence directly through the use of domestic wood as an energy source that offsets fossil fuel. It also works indirectly through conservation by the substitution of wood for higher embodied energy construction materials such as concrete and steel. Both the direct and indirect measures...

Profile extrusion and mechanical properties of crosslinked wood–thermoplastic composites

Treesearch

Magnus Bengtsson; Kristiina Oksman; Stark Nicole M.

2006-01-01

Challenges for wood-thermoplastic composites to be utilized in structural applications are to lower product weight and to improve the long-term load performance. Silane crosslinking of the composites is one way to reduce the creep during long-term loading and to improve the mechanical properties. In this study, silane crosslinked wood-polyethylene composites were...

CAPACITANCE SENSING OF MOISTURE CONTENT IN BIO-FUEL MATERIALS: A RAPID AND NONDESTRUCTIVE METHOD FOR WOOD CHIPS

USDA-ARS?s Scientific Manuscript database

Moisture content of wood chips is an important factor to be known in their utilization as biomass material. Several moisture measuring instruments are available in the market, but for most of these instruments, some sort of sample preparation is needed that involves sizing, grinding and weighing. T...

Utilization of treated conifer wood chips by Pleurotus (Fr.) P. Karst. species for cultivating mushrooms

Treesearch

Suki C. Croan

2003-01-01

Mushroom-producing white-rot basidiomycetes can grow rapidly and produce heavy mycelial growth on treated conifer wastes with extractive-degrading fungi. This study evaluates the treatment of scaled-up conifer wood chips with Ophiostoma piliferum (Cartapip 97). Treated conifer chips were used as substrates for cultivating mushroom-producing basidiomycetes of various...

Stem Sinuosity of Loblolly Pine Seedlings as Influenced by Taproot Shape

Treesearch

Michael S. Murphy; Timothy B. Harrington

2004-01-01

Sinuous stem growth in loblolly pine (Pinus taeda L.) results in diminished potential for the utilization of wood products since these stems are difficult to mill and contain a higher percentage of compression wood. In this study, 90 full-sibling loblolly pine seedlings (30 seedlings from each of 3 families) were planted with 5 taproot configurations...

Decay and termite resistance of medium density fiberboard (MDF) made from different wood species

Treesearch

S. Nami Kartal; Frederick Green

2003-01-01

Medium density fiberboard (MDF) production worldwide is increasing due to the development of new manufacturing technologies. As a result, MDF products are increasingly utilized in traditional wood applications that require fungal and insect resistance. This study evaluated the ability of white and brown rot fungi and termites to decompose MDF consisting of different...

Assessment of biodeterioration for the screening of new wood preservatives : calculation of stiffness loss in rapid decay testing

Treesearch

Simon R. Przewloka; Douglas M. Crawford; Douglas R. Rammer; Donald L. Buckner; Bessie M. Woodward; Gan Li; Darrel D. Nicholas

2008-01-01

Demand for the development of environmentally benign wood preservatives has increased significantly. To reduce the evaluation time of prospective candidates, reliable accelerated decay methodologies are necessary for laboratory screening of potential preservatives. Ongoing research at Mississippi State University has focused upon utilizing custom built equipment to...

Management for esthetics and recreation, forage, water, and wildlife

Treesearch

Norbert V. DeByle

1985-01-01

In the West, aspen forests have not been actively managed for wood products largely because of the lack of markets for quaking aspen timber from the Rocky Mountains (see the WOOD UTILIZATION chapter). Despite this, the aspen ecosystem has been used to provide a variety of resources and opportunities (see PART 111. RESOURCES AND USES).

Adhesive bonding of wood materials

Treesearch

Charles B. Vick

1999-01-01

Adhesive bonding of wood components has played an essential role in the development and growth of the forest products industry and has been a key factor in the efficient utilization of our timber resource. The largest use of adhesives is in the construction industry. By far, the largest amounts of adhesives are used to manufacture building materials, such as plywood,...

Tennesse Forest Acreage Increasing

Treesearch

R. L. Johnson

1961-01-01

Tennessee has 13,432,400 acres of commercial fore st land, according to a new suvey of the State's timber resources. All together, these woodIands occupy 51 percent of the total land are a in Tennessee. The estimate includes all forest land that is producing or is capable of producing industrial wood and not withdrawn from timber utilization. An additional 263,...

Utilization of sycamore

Treesearch

W.D. Brush

1920-01-01

Sycamore is one of the important commercial woods of the United States, and is of special value for use in certain containers, such as slack barrels and plug-tobacco boxes. It ranks low, however, in amount consumed, for about 25 native woods, including 13 hardwoods, are used in larger quantities. This bulletin gives information on the supply of sycamore, on the...

Characterization of a Composite Material to Mimic Human Cranial Bone

DTIC Science & Technology

2015-09-01

by Wood [3, 4]. The study utilized specimens from the craniums of 30 subjects ranging from age 25 to 95 years with an average age of 54 years...rates ranging from 0.005 to 150 sec-1. The cortical cranial bone data from Wood serves as a basis for comparison to the surrogate material under...78.0±9.7 GPa compared to 72.0±13.8 GPa for the cranial bones as measured in the study by Wood [4]. While the mean strength value of the simulant is

Efficiency and economic benefits of skipjack pole and line (huhate) in central Moluccas, Indonesia

NASA Astrophysics Data System (ADS)

Siahainenia, Stevanus M.; Hiariey, Johanis; Baskoro, Mulyono S.; Waeleruny, Wellem

2017-10-01

Excess fishing capacity is a crucial problem in marine capture fisheries. This phenomenon needed to be investigated regarding sustainability and development of the fishery. This research was aimed at analyzing technical efficiency (TE) and computing financial aspects of the skipjack pole and line. Primary data were collected from the owners of the fishing units at the different size of gross boat tonnage (GT), while secondary data were gathered from official publications relating to this research. Data envelopment analysis (DEA) approach was applied to estimate technical efficiency whereas a selected financial analysis was utilized to calculate economic benefits of the skipjack pole and line business. The fishing units with a size of 26-30 GT provided a higher TE value, and also achieved larger economic benefit values than that of the other fishing units. The empirical results indicate that skipjack pole and line in the size of 26-30 GT is a good fishing gear for the business development in central Moluccas.

First Observation of the {Lambda}(1405) Line Shape in Electroproduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Haiyun; Schumacher, Reinhard A.

2013-10-01

We report the first observation of the line shape of the {Lambda}(1405) from electroproduction, and show that it is not a simple Breit-Wigner resonance. Electroproduction of K{sup +}{Lambda}(1405) off the proton was studied by using data from CLAS at Jefferson Lab in the range 1.0

A variable-mode stator consequent pole memory machine

NASA Astrophysics Data System (ADS)

Yang, Hui; Lyu, Shukang; Lin, Heyun; Zhu, Z. Q.

2018-05-01

In this paper, a variable-mode concept is proposed for the speed range extension of a stator-consequent-pole memory machine (SCPMM). An integrated permanent magnet (PM) and electrically excited control scheme is utilized to simplify the flux-weakening control instead of relatively complicated continuous PM magnetization control. Due to the nature of memory machine, the magnetization state of low coercive force (LCF) magnets can be easily changed by applying either a positive or negative current pulse. Therefore, the number of PM poles may be changed to satisfy the specific performance requirement under different speed ranges, i.e. the machine with all PM poles can offer high torque output while that with half PM poles provides wide constant power range. In addition, the SCPMM with non-magnetized PMs can be considered as a dual-three phase electrically excited reluctance machine, which can be fed by an open-winding based dual inverters that provide direct current (DC) bias excitation to further extend the speed range. The effectiveness of the proposed variable-mode operation for extending its operating region and improving the system reliability is verified by both finite element analysis (FEA) and experiments.

Permanent Magnet Ecr Plasma Source With Magnetic Field Optimization

DOEpatents

Doughty, Frank C.; Spencer, John E.

2000-12-19

In a plasma-producing device, an optimized magnet field for electron cyclotron resonance plasma generation is provided by a shaped pole piece. The shaped pole piece adjusts spacing between the magnet and the resonance zone, creates a convex or concave resonance zone, and decreases stray fields between the resonance zone and the workpiece. For a cylindrical permanent magnet, the pole piece includes a disk adjacent the magnet together with an annular cylindrical sidewall structure axially aligned with the magnet and extending from the base around the permanent magnet. The pole piece directs magnetic field lines into the resonance zone, moving the resonance zone further from the face of the magnet. Additional permanent magnets or magnet arrays may be utilized to control field contours on a local scale. Rather than a permeable material, the sidewall structure may be composed of an annular cylindrical magnetic material having a polarity opposite that of the permanent magnet, creating convex regions in the resonance zone. An annular disk-shaped recurve section at the end of the sidewall structure forms magnetic mirrors keeping the plasma off the pole piece. A recurve section composed of magnetic material having a radial polarity forms convex regions and/or magnetic mirrors within the resonance zone.

Small-diameter utilization issues and opportunities

Treesearch

John Rusty Dramm

1999-01-01

This presentation provides a thought-provoking look at options for utilizing small- diameter wood to help reduce the widespread risk of catastrophic wildfire throughout the West while providing economic recovery of timber-depressed communities and sustaining viable forest products industry. Potentially viable utilization and marketing options are explored and current...

Lignin degradation: microorganisms, enzymes involved, genomes analysis and evolution.

PubMed

Janusz, Grzegorz; Pawlik, Anna; Sulej, Justyna; Swiderska-Burek, Urszula; Jarosz-Wilkolazka, Anna; Paszczynski, Andrzej

2017-11-01

Extensive research efforts have been dedicated to describing degradation of wood, which is a complex process; hence, microorganisms have evolved different enzymatic and non-enzymatic strategies to utilize this plentiful plant material. This review describes a number of fungal and bacterial organisms which have developed both competitive and mutualistic strategies for the decomposition of wood and to thrive in different ecological niches. Through the analysis of the enzymatic machinery engaged in wood degradation, it was possible to elucidate different strategies of wood decomposition which often depend on ecological niches inhabited by given organism. Moreover, a detailed description of low molecular weight compounds is presented, which gives these organisms not only an advantage in wood degradation processes, but seems rather to be a new evolutionatory alternative to enzymatic combustion. Through analysis of genomics and secretomic data, it was possible to underline the probable importance of certain wood-degrading enzymes produced by different fungal organisms, potentially giving them advantage in their ecological niches. The paper highlights different fungal strategies of wood degradation, which possibly correlates to the number of genes coding for secretory enzymes. Furthermore, investigation of the evolution of wood-degrading organisms has been described. © FEMS 2017.

Lignin degradation: microorganisms, enzymes involved, genomes analysis and evolution

PubMed Central

Pawlik, Anna; Sulej, Justyna; Świderska-Burek, Urszula; Jarosz-Wilkołazka, Anna; Paszczyński, Andrzej

2017-01-01

Abstract Extensive research efforts have been dedicated to describing degradation of wood, which is a complex process; hence, microorganisms have evolved different enzymatic and non-enzymatic strategies to utilize this plentiful plant material. This review describes a number of fungal and bacterial organisms which have developed both competitive and mutualistic strategies for the decomposition of wood and to thrive in different ecological niches. Through the analysis of the enzymatic machinery engaged in wood degradation, it was possible to elucidate different strategies of wood decomposition which often depend on ecological niches inhabited by given organism. Moreover, a detailed description of low molecular weight compounds is presented, which gives these organisms not only an advantage in wood degradation processes, but seems rather to be a new evolutionatory alternative to enzymatic combustion. Through analysis of genomics and secretomic data, it was possible to underline the probable importance of certain wood-degrading enzymes produced by different fungal organisms, potentially giving them advantage in their ecological niches. The paper highlights different fungal strategies of wood degradation, which possibly correlates to the number of genes coding for secretory enzymes. Furthermore, investigation of the evolution of wood-degrading organisms has been described. PMID:29088355

Improving wood properties for wood utilization through multi-omics integration in lignin biosynthesis

DOE PAGES

Wang, Jack P.; Matthews, Megan L.; Williams, Cranos M.; ...

2018-04-20

A multi-omics quantitative integrative analysis of lignin biosynthesis can advance the strategic engineering of wood for timber, pulp, and biofuels. Lignin is polymerized from three monomers (monolignols) produced by a grid-like pathway. The pathway in wood formation of Populus trichocarpa has at least 21 genes, encoding enzymes that mediate 37 reactions on 24 metabolites, leading to lignin and affecting wood properties. We perturb these 21 pathway genes and integrate transcriptomic, proteomic, fluxomic and phenomic data from 221 lines selected from ~2000 transgenics (6-month-old). The integrative analysis estimates how changing expression of pathway gene or gene combination affects protein abundance, metabolic-flux,more » metabolite concentrations, and 25 wood traits, including lignin, tree-growth, density, strength, and saccharification. The analysis then predicts improvements in any of these 25 traits individually or in combinations, through engineering expression of specific monolignol genes. The analysis may lead to greater understanding of other pathways for improved growth and adaptation.« less

Improving wood properties for wood utilization through multi-omics integration in lignin biosynthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jack P.; Matthews, Megan L.; Williams, Cranos M.

A multi-omics quantitative integrative analysis of lignin biosynthesis can advance the strategic engineering of wood for timber, pulp, and biofuels. Lignin is polymerized from three monomers (monolignols) produced by a grid-like pathway. The pathway in wood formation of Populus trichocarpa has at least 21 genes, encoding enzymes that mediate 37 reactions on 24 metabolites, leading to lignin and affecting wood properties. We perturb these 21 pathway genes and integrate transcriptomic, proteomic, fluxomic and phenomic data from 221 lines selected from ~2000 transgenics (6-month-old). The integrative analysis estimates how changing expression of pathway gene or gene combination affects protein abundance, metabolic-flux,more » metabolite concentrations, and 25 wood traits, including lignin, tree-growth, density, strength, and saccharification. The analysis then predicts improvements in any of these 25 traits individually or in combinations, through engineering expression of specific monolignol genes. The analysis may lead to greater understanding of other pathways for improved growth and adaptation.« less

Improving wood properties for wood utilization through multi-omics integration in lignin biosynthesis.

PubMed

Wang, Jack P; Matthews, Megan L; Williams, Cranos M; Shi, Rui; Yang, Chenmin; Tunlaya-Anukit, Sermsawat; Chen, Hsi-Chuan; Li, Quanzi; Liu, Jie; Lin, Chien-Yuan; Naik, Punith; Sun, Ying-Hsuan; Loziuk, Philip L; Yeh, Ting-Feng; Kim, Hoon; Gjersing, Erica; Shollenberger, Todd; Shuford, Christopher M; Song, Jina; Miller, Zachary; Huang, Yung-Yun; Edmunds, Charles W; Liu, Baoguang; Sun, Yi; Lin, Ying-Chung Jimmy; Li, Wei; Chen, Hao; Peszlen, Ilona; Ducoste, Joel J; Ralph, John; Chang, Hou-Min; Muddiman, David C; Davis, Mark F; Smith, Chris; Isik, Fikret; Sederoff, Ronald; Chiang, Vincent L

2018-04-20

A multi-omics quantitative integrative analysis of lignin biosynthesis can advance the strategic engineering of wood for timber, pulp, and biofuels. Lignin is polymerized from three monomers (monolignols) produced by a grid-like pathway. The pathway in wood formation of Populus trichocarpa has at least 21 genes, encoding enzymes that mediate 37 reactions on 24 metabolites, leading to lignin and affecting wood properties. We perturb these 21 pathway genes and integrate transcriptomic, proteomic, fluxomic and phenomic data from 221 lines selected from ~2000 transgenics (6-month-old). The integrative analysis estimates how changing expression of pathway gene or gene combination affects protein abundance, metabolic-flux, metabolite concentrations, and 25 wood traits, including lignin, tree-growth, density, strength, and saccharification. The analysis then predicts improvements in any of these 25 traits individually or in combinations, through engineering expression of specific monolignol genes. The analysis may lead to greater understanding of other pathways for improved growth and adaptation.

[Species identification of the fragment of wood found in the left eye socket bone during exhumation of general Władysław Sikorski's corpse].

PubMed

Wasik, Radosław

2009-01-01

During the exhumation of general Władysław Sikorski's corpse, a fragment of wood was found embedded in the left eye socket bone. The wood fragment was referred by the Institute of Forensic Research to the laboratory of Department of Forest and Wood Utilization, University of Agriculture in Krakow, where investigations were performed, aiming at determining the species of the wood. The fragment was cut into 20 microm thick microtome scraps of three anatomy sections: transverse, tangential and radial. The scraps were immersed in 99.8% ethyl alcohol for 24 hours and then for about 1 hour in xylene. Subsequently, they were placed between a microscope slide and a cover-glass in Canada balsam. The thus prepared scraps were then analyzed with the use of a Jenaval Carl Zeiss microscope. On the basis of microscope observations it was determined that the investigated fragment of wood belonged to Douglas-fir species (Pseudotsuga menziesii (Mirb.) Franco).

The Earliest Evidence of Holometabolan Insect Pupation in Conifer Wood

PubMed Central

Tapanila, Leif; Roberts, Eric M.

2012-01-01

Background The pre-Jurassic record of terrestrial wood borings is poorly resolved, despite body fossil evidence of insect diversification among xylophilic clades starting in the late Paleozoic. Detailed analysis of borings in petrified wood provides direct evidence of wood utilization by invertebrate animals, which typically comprises feeding behaviors. Methodology/Principal Findings We describe a U-shaped boring in petrified wood from the Late Triassic Chinle Formation of southern Utah that demonstrates a strong linkage between insect ontogeny and conifer wood resources. Xylokrypta durossi new ichnogenus and ichnospecies is a large excavation in wood that is backfilled with partially digested xylem, creating a secluded chamber. The tracemaker exited the chamber by way of a small vertical shaft. This sequence of behaviors is most consistent with the entrance of a larva followed by pupal quiescence and adult emergence — hallmarks of holometabolous insect ontogeny. Among the known body fossil record of Triassic insects, cupedid beetles (Coleoptera: Archostemata) are deemed the most plausible tracemakers of Xylokrypta, based on their body size and modern xylobiotic lifestyle. Conclusions/Significance This oldest record of pupation in fossil wood provides an alternative interpretation to borings once regarded as evidence for Triassic bees. Instead Xylokrypta suggests that early archostematan beetles were leaders in exploiting wood substrates well before modern clades of xylophages arose in the late Mesozoic. PMID:22355387

Asthma randomized trial of indoor wood smoke (ARTIS): Rationale and Methods

PubMed Central

Noonan, Curtis W.; Ward, Tony J.

2012-01-01

Background Particulate matter (PM) exposures have been linked with poor respiratory health outcomes, especially among susceptible populations such as asthmatic children. Smoke from biomass combustion for residential home heating is an important source of PM in many rural or peri-urban areas in the United States. Aim To assess the efficacy of residential interventions that reduce indoor PM exposure from wood stoves and to quantify the corresponding improvements in quality of life and health outcomes for asthmatic children. Design The Asthma Randomized Trial of Indoor wood Smoke (ARTIS) study is an in-home intervention study of susceptible children exposed to biomass combustion smoke. Children, ages 7 to 17, with persistent asthma and living in homes that heat with wood stoves were recruited for this three arm randomized placebo-controlled trial. Two household-level intervention strategies, wood stove replacement and air filters, were compared to a sham air filter placebo. Improvement in quality of life of asthmatic children was the primary outcomes. Secondary asthma-related health outcomes included peak expiratory flow (PEF) and forced expiratory volume in first second (FEV1), biomarkers in exhaled breath condensate, and frequency of asthma symptoms, medication usage, and healthcare utilization. Exposure outcomes included indoor and outdoor PM2.5 mass, particle counts of several size fractions, and carbon monoxide. Discussion To our knowledge, this was the first randomized trial in the US to utilize interventions targeting residential wood stoves to assess the impact on indoor PM and health outcomes in a susceptible population. Trial registration ClincialTrials.gov NCT00807183. PMID:22735495

Wood and coal cofiring in interior Alaska: utilizing woody biomass from wildland defensible-space fire treatments and other sources.

Treesearch

David L. Nicholls; Stephen E. Patterson; Erin Uloth

2006-01-01

Cofiring wood and coal at Fairbanks, Alaska, area electrical generation facilities represents an opportunity to use woody biomass from clearings within the borough's wildland-urban interface and from other sources, such as sawmill residues and woody material intended for landfills. Potential benefits of cofiring include air quality improvements, reduced greenhouse...

Contents of a cord of eight-foot pulpwood.

Treesearch

Norman P. Worthington; Melvin P. Twerdal

1950-01-01

Although the pulp and paper industry of western Washington depends chiefly on logs for its wood supply, the use of pulpwood in cordwood lengths is steadily increasing. More than 75 percent of the 20 plants in the area are equipped to handle at least a part of their consumption in cordwood form. Many plants are remodeling their facilities to utilize additional wood...

Preliminary evaluation of storax and its constituents: Fungal decay mold and termite resistance

Treesearch

S. Nami Kartal; Evren Terzi; Tsuyoshi Yoshimura; Rachel Arango; Carol A. Clausen; Frederick Green III

2012-01-01

Essential oils and their derivatives might be one of the promising preserving agents to prevent funga ldecay and termite/insect attack in wood since such compounds have a long history of safe usage as antimicrobial agents in various industries. Considerable research has focused on utilizing bioactive essential oils and wood extractives based on green technologies to...

Wood products utilization : a call for reflection and innovation

Treesearch

John A. Youngquist; Thomas E. Hamilton

1999-01-01

It is hard to imagine a world without forests. Forests provide a wide range of benefits at the local, national, and global levels. Some of these benefits depend on leaving the forest alone or subjecting it to only minimal interference. Other benefits can only be realized by harvesting the forest for wood and other products. The shrinking land base and growing human...

Estimating sawmill processing capacity for Tongass timber: 2009 and 2010 Update

Treesearch

Susan J. Alexander; Daniel J. Parrent

2012-01-01

In spring and summer of 2010 and 2011, sawmill production capacity and wood utilization information was collected from major wood manufacturers in southeast Alaska. The estimated mill capacity in southeast Alaska for calendar year (CY) 2009 was 249,350 thousand board feet (mbf) (log scale), and for CY 2010 was 155,850 mbf (log scale), including idle sawmills. Mill...

Semi-solid state bioremediation of CCA-treated wood using malted barley as a nutrient source

Treesearch

Carol A. Clausen

2002-01-01

Bioremediation processes for recovery and reuse of CCA-treated wood invariably increase the cost of any secondary products manufactured from the remediated fiber. Microbial remediation using either bacteria or fungi has been shown to remove heavy metals from CCA-treated southern yellow pine (SYP). In a two-step remediation process utilizing oxalic acid extraction and...

Significant alteration of gene expression in wood decay fungi Postia placenta and Phanerochaete chrysosporium by plant species

Treesearch

Amber Vanden Wymelenberg; Jill Gaskell; Michael Mozuch; Sandra Splinter BonDurant; Grzegorz Sabat; John Ralph; Oleksandr Skyba; Shawn D. Mansfield; Robert A. Blanchette; Igor Grigoriev; Philip J. Kersten; Daniel Cullen

2011-01-01

Identification of specific genes and enzymes involved in conversion of lignocellulosics from an expanding number of potential feedstocks is of growing interest to bioenergy process development. The basidiomycetous wood decay fungi Phanerochaete chrysosporium and Postia placenta are promising in this regard because they are able to utilize a wide range of simple and...

Alaska forest products: using resources well.

Treesearch

Valerie Rapp

2003-01-01

Despite abundant forest resources in the state, the Alaska forest products industry declined throughout the 1990s and early 21st century. In a state with lots of trees, mills are going out of business and most finished lumber used in the state is imported from the lower 48 United States and Canada. The Alaska Wood Utilization Research and Development Center (Wood...

Identifying markets for pinyon pine in the Four Corners Region

Treesearch

Kurt H. Mackes

2008-01-01

A search for opportunities to use pinyon pine is currently being conducted at Colorado State University by the Colorado Wood Utilization and Marketing Program as part of an effort to improve financial feasibility of forest restoration and hazardous fuel reduction work in pinyon-juniper stands. The properties of pinyon wood reveal that it is suitable for a range of...

An integrated approach to evaluating the economic costs of wildfire hazard reduction through wood utilization opportunities in the southwestern United States

Treesearch

Eini C. Lowell; Dennis R. Becker; Robert Rummer; Debra Larson; Linda Wadleigh

2008-01-01

This research provides an important step in the conceptualization and development of an integrated wildfire fuels reduction system from silvicultural prescription, through stem selection, harvesting, in-woods processing, transport, and market selection. Decisions made at each functional step are informed by knowledge about subsequent functions. Data on the resource...

An integrated approach to evaluating the economic costs of wildfire hazard reduction through wood utilization opportunities in the Southwestern United States

Treesearch

Eini C. Lowell; Dennis R. Becker; Robert Rummer; Debra Larson; Linda Wadleigh

2008-01-01

This research provides an important step in the conceptualization and development of an integrated wildfire fuels reduction system from silvicultural prescription, through stem selection, harvesting, in-woods processing, transport, and market selection. Decisions made at each functional step are informed by knowledge about subsequent functions. Data on the resource...

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model.

PubMed

Liang, Sai; Zhang, Tianzhu; Xu, Yijian

2012-03-01

Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for paper production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment. Copyright © 2011 Elsevier Ltd. All rights reserved.

Simulated long-term effects of varying tree retention on wood production, dead wood and carbon stock changes.

PubMed

Santaniello, Francesca; Djupström, Line B; Ranius, Thomas; Weslien, Jan; Rudolphi, Jörgen; Sonesson, Johan

2017-10-01

Boreal forests are an important source of timber and pulp wood, but provide also other products and services. Utilizing a simulation program and field data from a tree retention experiment in a Scots pine forest in central Sweden, we simulated the consequences during the following 100 years of various levels of retention on production of merchantable wood, dead wood input (as a proxy for biodiversity), and carbon stock changes. At the stand level, wood production decreased with increased retention levels, while dead wood input and carbon stock increased. We also compared 12 scenarios representing a land sharing/land sparing gradient. In each scenario, a constant volume of wood was harvested with a specific level of retention in a 100-ha landscape. The area not needed to reach the defined volume was set-aside during a 100-year rotation period, leading to decreasing area of set-asides with increasing level of retention across the 12 scenarios. Dead wood input was positively affected by the level of tree retention whereas the average carbon stock decreased slightly with increasing level of tree retention. The scenarios will probably vary in how they favor species preferring different substrates. Therefore, we conclude that a larger variation of landscape-level conservation strategies, also including active creation of dead wood, may be an attractive complement to the existing management. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soil quality in a cropland soil treated with wood ash containing charcoal

NASA Astrophysics Data System (ADS)

Omil, Beatriz; Balboa, Miguel A.; Fonturbel, M. Teresa; Gartzia-Bengoetxea, Nahia; Arias-González, Ander; Vega, Jose A.; Merino, Agustin

2014-05-01

The strategy of the European Union "Europe 2020" states that by 2020, 20% of final energy consumption must come from renewables. In this scenario, there is an increasing use of biomass utilization for energy production. Indeed, it is expected that the production of wood-ash will increase in coming years. Wood ash, a mixture of ash and charcoal, generated as a by-product of biomass combustion in power plants, can be applied to soil to improve the soil quality and crop production. Since the residue contains significant content of charcoal, the application of mixed wood ash may also improve the SOM content and soil quality in the long term, in soils degraded as a consequence of intensive management. The objective of this study was asses the changes in SOM quality and soil properties in a degraded soils treated with wood ash containing charcoal. The study was carried out in a field devoted to cereal crops during the last decades. The soil was acidic (pH 4.5) with a low SOC content (3 %) and fine texture. The experiment was based on a randomised block design with four replicates. Each block included the following four treatments: Control, 16 Mg fly wood ash ha-1, 16 Mg mixed wood ash ha-1 (16 Mg) and 32 Mg mixed wood ash ha-1 (32 Mg). The application was carried out once. The ash used in the study was obtained from a thermal power plant and was mainly derived from the combustion of Pinus radiata bark and branches. The wood ash is highly alkaline (pH= 10), contains 10 % of highly condensed black carbon (atomic H/C ratio < 0.5 and T50 en DSC= 500 ºC). The evolution of SOM properties were monitored over three years by solid state 13C CPMAS NMR and Differential Scanning Calorimetry (DSC). These techniques were applied in bulk samples and aggregates of different sizes. The changes in microbial activity were studied by analysis of microbial biomass C and basal respiration. The soil bacterial community was studied by the Biolog method. Several physical properties, such soil aggregate distribution, hydraulic conductivity and available water contente were also determined. Three years after applications the SOM content increased lightly in the treatment receiving more than 16 Mg ha-1 of wood ash. SOM in the treated soils displayed a higher degree of aromaticity than in the untreated soils, indicating a gain in more stable SOM compounds probably as a consequence of the charcoal application. However, both methods also revealed increases in labile C compounds, probably due to the carbohydrates added through root system. Microbial biomass-C and soil respiration increased significantly. The treatments also led to increases in the functional diversity indices. The amended soils showed greater utilization of substrates and the ability of soil bacteria to utilize different C resources was also greatly altered. The application of mixed wood ash did not lead to any difference in MWD, which was around 6 mm in all cases. The application of 16 Mg fly wood ash ha-1 increased significantly the hydraulic conductivity (4.07 cmh-1) when compared with in control plots (1.3 cmh-1) and mixed ash plots (1.52 and 2.45 cmh-1, 16 Mg and 32 Mg respectively). However, air-filled porosity was not higher in 16 Mg fly ash plots. AWC was not improved by wood ash application.

Roadway Safety Guide

DOT National Transportation Integrated Search

2001-01-01

Roadway safety refers to that portion of overall highway safety that is determined by the roadway's physical features such as road design, roadway signs, pavement markings, operating conditions, roadside objects (such as utility poles, signs, trees, ...

46 CFR 183.220 - General safety provisions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... current utilized. (c) Receptacle outlets of the type providing a grounded pole or a specific direct current polarity must be of a configuration that will not permit improper connection. (d) All electrical...

46 CFR 183.220 - General safety provisions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... current utilized. (c) Receptacle outlets of the type providing a grounded pole or a specific direct current polarity must be of a configuration that will not permit improper connection. (d) All electrical...

Plasma impregnation of wood with fire retardants

NASA Astrophysics Data System (ADS)

Pabeliña, Karel G.; Lumban, Carmencita O.; Ramos, Henry J.

2012-02-01

The efficacy of chemical and plasma treatments with phosphate and boric compounds, and nitrogen as flame retardants on wood are compared in this study. The chemical treatment involved the conventional method of spraying the solution over the wood surface at atmospheric condition and chemical vapor deposition in a vacuum chamber. The plasma treatment utilized a dielectric barrier discharge ionizing and decomposing the flame retardants into innocuous simple compounds. Wood samples are immersed in either phosphoric acid, boric acid, hydrogen or nitrogen plasmas or a plasma admixture of two or three compounds at various concentrations and impregnated by the ionized chemical reactants. Chemical changes on the wood samples were analyzed by Fourier transform infrared spectroscopy (FTIR) while the thermal changes through thermo gravimetric analysis (TGA). Plasma-treated samples exhibit superior thermal stability and fire retardant properties in terms of highest onset temperature, temperature of maximum pyrolysis, highest residual char percentage and comparably low total percentage weight loss.

Application of a forest-simulation model to assess the energy yield and ecological impact of forest utilization for energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doyle, T W; Shugart, H H; West, D C

1981-01-01

This study examines the utilization and management of natural forest lands to meet growing wood-energy demands. An application of a forest simulation model is described for assessing energy returns and long-term ecological impacts of wood-energy harvesting under four general silvicultural practices. Results indicate that moderate energy yields could be expected from mild cutting operations which would significantly effect neither the commercial timber market nor the composition, structure, or diversity of these forests. Forest models can provide an effective tool for determining optimal management strategies that maximize energy returns, minimize environmental detriment, and complement existing land-use plans.

Favorable outcome of patients with lung adenocarcinoma harboring POLE mutations and expressing high PD-L1.

PubMed

Liu, Liang; Ruiz, Jimmy; O'Neill, Stacey S; Grant, Stefan C; Petty, W Jeffrey; Yang, Meng; Chen, Kexin; Topaloglu, Umit; Pasche, Boris; Zhang, Wei

2018-04-12

Mutations in polymerase ε (POLE) confer favorable prognosis and outcomes in various cancer types, but their role in non-small cell lung cancer (NSCLC) is unknown. Utilizing the data of 513 patients with adenocarcinoma (LUAD) and 497 patients with squamous cell carcinoma (LUSC) from The Cancer Genome Atlas (TCGA) cohort, we tested the prognostic value of POLE mutations and programmed cell death ligand 1 (PD-L1) expression in the two main subtypes of NSCLC. POLE mutation is a favorable biomarker for the improved overall survival (OS) of the LUSC patients (P = 0.033, 28 mutant vs. 469 wildtype patients), but not that of the LUAD patients (P = 0.12, 31 mutant vs. 482 wildtype patients). POLE-mutant LUAD patients with high expression of PD-L1 (Mut-High, n = 6) exhibited improved OS (P = 0.024) when compared to POLE-mutant patients with low PD-L1 expression (Mut-Low, n = 24) and other patients without POLE mutation (n = 476). This benefit was not due to the high content of the tumor infiltrating lymphocytes. Instead, the antitumor immune response was activated in Mut-High patients so that these patients were likely responding more effectively to immuno-oncology (IO) treatments; whereas genes involved with metabolic pathways were enriched in Mut-Low group, which may cause the decreased OS of these patients. Our study sheds light on the molecular basis of NSCLC and adds to our understanding of responses to chemotherapy and IO therapy.

Automatic pole-like object modeling via 3D part-based analysis of point cloud

NASA Astrophysics Data System (ADS)

He, Liu; Yang, Haoxiang; Huang, Yuchun

2016-10-01

Pole-like objects, including trees, lampposts and traffic signs, are indispensable part of urban infrastructure. With the advance of vehicle-based laser scanning (VLS), massive point cloud of roadside urban areas becomes applied in 3D digital city modeling. Based on the property that different pole-like objects have various canopy parts and similar trunk parts, this paper proposed the 3D part-based shape analysis to robustly extract, identify and model the pole-like objects. The proposed method includes: 3D clustering and recognition of trunks, voxel growing and part-based 3D modeling. After preprocessing, the trunk center is identified as the point that has local density peak and the largest minimum inter-cluster distance. Starting from the trunk centers, the remaining points are iteratively clustered to the same centers of their nearest point with higher density. To eliminate the noisy points, cluster border is refined by trimming boundary outliers. Then, candidate trunks are extracted based on the clustering results in three orthogonal planes by shape analysis. Voxel growing obtains the completed pole-like objects regardless of overlaying. Finally, entire trunk, branch and crown part are analyzed to obtain seven feature parameters. These parameters are utilized to model three parts respectively and get signal part-assembled 3D model. The proposed method is tested using the VLS-based point cloud of Wuhan University, China. The point cloud includes many kinds of trees, lampposts and other pole-like posters under different occlusions and overlaying. Experimental results show that the proposed method can extract the exact attributes and model the roadside pole-like objects efficiently.

Biomass utilization modeling on the Bitterroot National Forest

Treesearch

Robin P. Silverstein; Dan Loeffler; J. Greg Jones; Dave E. Calkin; Hans R. Zuuring; Martin Twer

2006-01-01

Utilization of small-sized wood (biomass) from forests as a potential source of renewable energy is an increasingly important aspect of fuels management on public lands as an alternative to traditional disposal methods (open burning). The potential for biomass utilization to enhance the economics of treating hazardous forest fuels was examined on the Bitterroot...

Methyl bromide as a quarantine treatment for Chlorophorus annularis (Coleoptera: Cerambycidae) in raw bamboo poles.

PubMed

Barak, Alan V; Weidong, Yang; Daojian, Yu; Yi, Jiao; Lin, Kang; Zhilin, Chen; Xingyuan, Ling; Guoping, Zhan

2009-06-01

At least 26 different species of insects of quarantine significance were intercepted from 1985 to 2005 on bamboo (Bambusa spp.) garden stakes from China. Three fifths of the live insects were cerambycids in nine genera, including Chlorophorus annularis F., the bamboo borer. The current APHIS-PPQ treatment is fumigation schedule T404-d, which requires high doses of methyl bromide (MeBr) for 24 h. No specific fumigation data exist for C. annularis. Chinese and American quarantine scientists cooperated in testing to determine whether this schedule, or lower doses, would be effective as a quarantine treatment for C. annularis infesting dried bamboo poles. A lower dose based on APHIS tests for solid wood packing (SWP) failed (3/511 survivors) at 56 g/m3 for 24 h at 10.0 degrees C. We therefore tested five progressive doses at five temperatures intermediate between the lower SWP schedule and the much higher applied doses (e.g., 120 g/m3 for 24 h at 10.0 degrees C) of schedule T404-d. Fumigations of infested bamboo poles conducted in 403.2-liter chambers with 52% vol:vol loading at doses of 48, 64, 80, 96, and 112 g/m3 at 26.7, 21.1, 15.6, 10.0, and 4.4 degrees C, respectively (20 total replicates, with 4 replicates per dose), had no survivors among 2,847 larvae, 140 pupae, and 122 adults. Control replicates (three) had a total of 455 live stages (397 larvae, 31 pupae, and 27 adults). Tests conducted with a sea/land cargo container loaded to 80% capacity with bamboo poles verified the ability of the schedule to maintain effective concentrations over 24 h in commercial-sized fumigations. We propose a new bamboo quarantine treatment schedule at reduced rates of applied MeBr.

Wood wastes and residues generated along the Colorado Front Range as a potential fuel source

Treesearch

Julie E. Ward; Kurt H. Mackes; Dennis L. Lynch

2004-01-01

Throughout the United States there is interest in utilizing renewable fuel sources as an alternative to coal and nat-ural gas. This project was initiated to determine the availability of wood wastes and residues for use as fuel in ce-ment kilns and power plants located along the Colorado Front Range. Research was conducted through literature searches, phone surveys,...

Ecological succession leads to chemosynthesis in mats colonizing wood in sea water.

PubMed

Kalenitchenko, Dimitri; Dupraz, Marlène; Le Bris, Nadine; Petetin, Carole; Rose, Christophe; West, Nyree J; Galand, Pierre E

2016-09-01

Chemosynthetic mats involved in cycling sulfur compounds are often found in hydrothermal vents, cold seeps and whale falls. However, there are only few records of wood fall mats, even though the presence of hydrogen sulfide at the wood surface should create a perfect niche for sulfide-oxidizing bacteria. Here we report the growth of microbial mats on wood incubated under conditions that simulate the Mediterranean deep-sea temperature and darkness. We used amplicon and metagenomic sequencing combined with fluorescence in situ hybridization to test whether a microbial succession occurs during mat formation and whether the wood fall mats present chemosynthetic features. We show that the wood surface was first colonized by sulfide-oxidizing bacteria belonging to the Arcobacter genus after only 30 days of immersion. Subsequently, the number of sulfate reducers increased and the dominant Arcobacter phylotype changed. The ecological succession was reflected by a change in the metabolic potential of the community from chemolithoheterotrophs to potential chemolithoautotrophs. Our work provides clear evidence for the chemosynthetic nature of wood fall ecosystems and demonstrates the utility to develop experimental incubation in the laboratory to study deep-sea chemosynthetic mats.

Environmental impact assessment of wood ash utilization in forest road construction and maintenance--A field study.

PubMed

Oburger, Eva; Jäger, Anna; Pasch, Alexander; Dellantonio, Alex; Stampfer, Karl; Wenzel, Walter W

2016-02-15

The ever increasing use of wood material as fuel for green energy production requires innovative, environmentally safe strategies for recycling of the remaining wood ash. Utilizing wood ash in forest road construction and maintenance to improve mechanical stability has been suggested as a feasible recycling option. To investigate the environmental impact of wood ash application in forest road maintenance, a two-year field experiment was conducted at two Austrian forest sites (Kobernausserwald (KO) (soil pH 5.5) and Weyregg (WE) (pH 7.7)) differing in their soil chemical properties. Two different ashes, one produced by grate incineration (GA) and the other by fluidized bed incineration in a mixture with 15 vol% burnt lime (FBA), were incorporated in repeated road sections at a 15:85% (V/V) ash-to-soil rate. Leaching waters from the road body were collected and analyzed for 32 environmentally relevant parameters over two years. Upon termination of the experiment, sub-road soil samples were collected and analyzed for ash-related changes in soil chemistry. Even though a larger number of parameters was affected by the ash application at the alkaline site (WE), we observed the most pronounced initial increases of pH as well as Al, As, Fe, Mn, Ni, Co, Cu, Mo, and NO2(−) concentrations in leachates beneath GA-treated road bodies at Kobernausserwald due to the lower soil buffer capacity at this site. Despite the observed effects our results indicate that, when specific requirements are met (i.e. appropriate ash quality, sufficient soil buffer capacity below the road body, and single time-point ash incorporation within several decades), wood ash application in forest road construction is generally environmentally acceptable.

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang Sai; Zhang, Tianzhu, E-mail: zhangtz@mail.tsinghua.edu.cn; Xu Yijian

Highlights: Black-Right-Pointing-Pointer Using crop straws and wood wastes for paper production should be promoted. Black-Right-Pointing-Pointer Bagasse and textile waste recycling should be properly limited. Black-Right-Pointing-Pointer Imports of scrap paper should be encouraged. Black-Right-Pointing-Pointer Sensitivity analysis, uncertainties and policy implications are discussed. - Abstract: Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for papermore » production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment.« less

Gender differences in power production, energetic capacity and efficiency of elite cross‑country skiers during whole‑body, upper‑body, and arm poling.

PubMed

Hegge, Ann Magdalen; Bucher, Elias; Ettema, Gertjan; Faude, Oliver; Holmberg, Hans-Christer; Sandbakk, Øyvind

2016-02-01

To characterize gender differences in power output, energetic capacity and exercise efficiency during whole-body (WP), upper-body (UP), and arm poling (AP). Ten male and ten female elite cross-country skiers, matched for international performance level, completed three incremental submaximal tests and a 3-min self-paced performance test on a Concept2 SkiErg. Power output, cardiorespiratory and kinematic variables were monitored. Body composition was determined by dual-energy X-ray absorptiometry. The men demonstrated 87, 97 and 103% higher power output, and 51, 65 and 71% higher VO2peak (L min(−1)) than the women during WP, UP and AP, respectively, while utilizing ~10% more of their running VO2max in all modes (all P < 0.001). The men had 35, 38 and 59% more lean mass in the whole body, upper body and arms (all P < 0.001). The men exhibited greater shoulder and elbow extension at the start of poling and greater trunk flexion at the end of poling (all P < 0.05). The relationship between VO2 and power output did not differ between the men and women. Gender differences in power production and peak aerobic capacity increased sequentially from WP to UP to AP, coinciding with a greater portion of the muscle mass in the arms of the men. Although the men and women employed each poling technique differently, the estimated efficiency of double poling was independent of gender.

Evaluation of the antifungal effects of bio-oil prepared with lignocellulosic biomass using fast pyrolysis technology.

PubMed

Kim, Kwang Ho; Jeong, Han Seob; Kim, Jae-Young; Han, Gyu Seong; Choi, In-Gyu; Choi, Joon Weon

2012-10-01

This study was performed to investigate the utility of bio-oil, produced via a fast pyrolysis process, as an antifungal agent against wood-rot fungi. Bio-oil solutions (25-100 wt.%) were prepared by diluting the bio-oil with EtOH. Wood block samples (yellow poplar and pitch pine) were treated with diluted bio-oil solutions and then subjected to a leaching process under hot water (70°C) for 72 h. After the wood block samples were thoroughly dried, they were subjected to a soil block test using Tyromyces palustris and Trametes versicolor. The antifungal effect of the 75% and 100% bio-oil solutions was the highest for both wood blocks. Scanning electron microscopy analysis indicated that some chemical components in the bio-oil solution could agglomerate together to form clusters in the inner part of the wood during the drying process, which could act as a wood preservative against fungal growth. According to GC/MS analysis, the components of the agglomerate were mainly phenolic compounds derived from lignin polymers. Copyright © 2012 Elsevier Ltd. All rights reserved.

Contextual view of Goerlitz Property, showing eucalyptus trees along west ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Contextual view of Goerlitz Property, showing eucalyptus trees along west side of driveway; parking lot and utility pole in foreground. Camera facing 38" northeast - Goerlitz House, 9893 Highland Avenue, Rancho Cucamonga, San Bernardino County, CA

Comparison of the Heat Release Rate from the Mass Loss Calorimeter to the Cone Calorimeter for Wood-based Materials

Treesearch

Laura E. Hasburgh; Robert H. White; Mark A. Dietenberger; Charles R. Boardman

2015-01-01

There is a growing demand for material properties to be used as inputs in fi re behavior models designed to address building fire safety. This comparative study evaluates using the mass loss calorimeter as an alternative to the cone calorimeter for obtaining heat release rates of wood-based materials. For this study, a modified mass loss calorimeter utilized an...

Utilization of mill residues in the timber products mills of the Lakeview Working Circle.

Treesearch

A.C. Knauss

1953-01-01

The manufacture of lumber from logs is always accompanied by the accumulation of wood fiber in the form of sawdust, slabs, edgings, trim, and shavings which is of little commercial value. Sawmills use a portion of this "residual" wood fiber for generating steam with which to run the mill and dry kilns, some is used as a raw material for other industries, but...

Environmental Assessment for Proposed Utility Corridors at Edwards Air Force Base, California

DTIC Science & Technology

2016-07-01

fossil fuels (coal, natural gas and oil), solid waste, trees and wood products, and also as a result of certain chemical reactions (e.g...Colonization companies representing Quakers, German Lutherans, Scots , English and others began to promote settlement of the southern Antelope...Federal: State: Local: None SSC WEMO Covered Species Nesting in large trees; foraging in most habitats; on Base in wooded areas such as woodlands

Structural wood products in onshore buildings at Naval Station Norfolk, 2000.

Treesearch

David B. McKeever

2003-01-01

As of December 31, 2000, there were 603 buildings at Naval Station (NAVSTA) Norfolk with a combined floor area of nearly 17.3 million ft2. In one-third of these buildings, structural wood products were used in one or more major structural building applications, utilizing an estimated 11.6 million board feet of lumber, 0.4 million ft2 (3/8-in. basis) of structural...

The Colville Study: wood utilization for ecosystem management: preliminary results of study of product potential from small-diameter stands.

Treesearch

S. Willits; R. J. Barbour; J. McNeel; R. D. Fight; G. C. Myers; A. Mason

The Colville Study was developed in 1994 to identify and evaluate a series of management options for achieving ecosystem objectives in dense stands of small-diameter trees while also producing wood products. The Colville National Forest selected the Rocky II Timber Sale as an example of this type of stand that needed management to achieve the following goals: (1)...

Influence of Water on Tribological Properties of Wood-Polymer Composites

NASA Astrophysics Data System (ADS)

Mysiukiewicz, Olga; Sterzyński, Tomasz

2017-08-01

Utilization of ecological materials for appliances and products is one of the ways to achieve the goal of sustainability.Wood-polymer composites as a cheap, lightweight, durable and esthetic material has gained attention of scientists, engineers and consumers alike. Different kinds of polymeric matrices, plants used as the fillers, chemical of physical modifiers and processing technologies have already been widely studied. Nonetheless, surprisingly few information on Wood-Polymer Composites' tribology can be found. This paper is an attempt to fill this gap. Polypropylene-and poly(lactic acid)-based composites with varying wood flour content have been analyzed. The Brinell's hardness and coefficient of friction of the samples have been determined. In order to evaluate the influence of the moisture content on the tribological and mechanical properties of the composites, the samples have also been aged in water. The investigation revealed that polymeric composites filled with wood flour can present favorable coefficient of friction, compared to the neat resins. The results of our study can establish a good starting point for further investigation.

The effects of heat treatment on technological properties in Red-bud maple (Acer trautvetteri Medw.) wood.

PubMed

Korkut, Süleyman; Kök, M Samil; Korkut, Derya Sevim; Gürleyen, Tuğba

2008-04-01

Heat treatment is often used to improve the dimensional stability of wood. In this study, the effects of heat treatment on technological properties of Red-bud maple (Acer trautvetteri Medw.) wood were examined. Samples obtained from Düzce Forest Enterprises, Turkey, were subjected to heat treatment at varying temperatures (120 degrees C, 150 degrees C and 180 degrees C) and for varying durations (2h, 6h and 10h). The technological properties of heat-treated wood samples and control samples were tested. Compression strength parallel to grain, bending strength, modulus of elasticity in bending, janka-hardness, impact bending strength, and tension strength perpendicular to grain were determined. The results showed that technological strength values decreased with increasing treatment temperature and treatment times. Red-bud maple wood could be utilized by using proper heat treatment techniques with minimal losses in strength values in areas where working, and stability such as in window frames, are important factors.

Extraordinary-mode refractive-index change produced by the linear electro-optic effect in LiNbO3 and reverse-poled LiNbO3

NASA Astrophysics Data System (ADS)

Boyd, Joseph T.; Servizzi, Anthony J.; Sriram, S.; Kingsley, Stuart A.

1995-07-01

To examine aspects of an integrated photonic electric-field sensor, we calculate electro-optically induced refractive-index change in regular and reverse-poled LiNbO3. Specifically, for y-propagating extraordinary modes, we determine how index change depends on electric-field magnitude and direction. To accomplish this, changes in index-ellipsoid shape and orientation are found by the use of a numerical eigenvalue procedure to diagonalize the impermeability tensor; then, refractive index is calculated by the use of a vector reference-frame transformation and a small perturbation approximation. A general formula is inferred from calculations for specific field directions. Electro-optic coefficients for reverse-poled LiNbO3 are obtained by application of a tensor reference-frame transformation to those of LiNbO3. The index-calculation procedure has utility beyond the problem that is considered.

History of energy sources and their utilization in Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogunsola, O.I.

1990-01-01

Nigeria, a major oil producer, is rich in other energy sources. These include wood, coal, gas, tar sands, and hydro power. Although oil has been the most popular, some other energy sources have a longer history. This article discusses the historical trends in the production and utilization of Nigerian energy sources. Wood has the longest history. However,its utilization was limited to domestic cooking. Imported coal was first used in 1896, but it was not discovered in Nigeria until 1909 and was first produced in 1916. Although oil exploration started in 1901, it was first discovered in commercial quantity in 1956more » and produced in 1958. Oil thereafter took over the energy scene from coal until 1969, when hydro energy was first produced. Energy consumption has been mainly from hydro. Tar sands account for about 55% of total proven non-renewable reserves.« less

Simulated nitrogen deposition affects wood decomposition by cord-forming fungi.

PubMed

Bebber, Daniel P; Watkinson, Sarah C; Boddy, Lynne; Darrah, Peter R

2011-12-01

Anthropogenic nitrogen (N) deposition affects many natural processes, including forest litter decomposition. Saprotrophic fungi are the only organisms capable of completely decomposing lignocellulosic (woody) litter in temperate ecosystems, and therefore the responses of fungi to N deposition are critical in understanding the effects of global change on the forest carbon cycle. Plant litter decomposition under elevated N has been intensively studied, with varying results. The complexity of forest floor biota and variability in litter quality have obscured N-elevation effects on decomposers. Field experiments often utilize standardized substrates and N-levels, but few studies have controlled the decay organisms. Decomposition of beech (Fagus sylvatica) blocks inoculated with two cord-forming basidiomycete fungi, Hypholoma fasciculare and Phanerochaete velutina, was compared experimentally under realistic levels of simulated N deposition at Wytham Wood, Oxfordshire, UK. Mass loss was greater with P. velutina than with H. fasciculare, and with N treatment than in the control. Decomposition was accompanied by growth of the fungal mycelium and increasing N concentration in the remaining wood. We attribute the N effect on wood decay to the response of cord-forming wood decay fungi to N availability. Previous studies demonstrated the capacity of these fungi to scavenge and import N to decaying wood via a translocating network of mycelium. This study shows that small increases in N availability can increase wood decomposition by these organisms. Dead wood is an important carbon store and habitat. The responses of wood decomposers to anthropogenic N deposition should be considered in models of forest carbon dynamics.

Energy from wood biomass: The experience of the Brazilian forest sector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couto, L.; Graca, L.R.; Betters, D.R.

Wood biomass is one of the most significant renewable sources of energy in Brazil. Fuelwood and charcoal play a very important role not only for household energy consumption but also for the cement, iron and steel industries. Wood is used as an energy source by the pulp and paper, composite board and other industries of the country, mainly for steam and electricity generation. Ethanol, lignin-based coke and methanol from wood were produced at experimental units in Brazil but were not implemented on a commercial scale. Currently, a new experimental plant using a technology developed in the US is being builtmore » in the state of Bahia to generate electricity from Eucalyptus. This technology is a Biomass Integrated Gasification/Gas Turbine process which is expected to make the use of wood biomass economically feasible for electricity generation. Forest plantations are the main source of wood biomass for energy consumption by the Brazilian industrial sector. Fiscal incentives in the 1960s helped the country to begin a massive reforestation program mainly using Eucalyptus and Pinus species. A native species, bracatinga (Mimosa scabrella) has also been used extensively for wood energy plantations in southern Brazil. Technical, economic, social and environmental impacts of these plantation forests are discussed along with a forecast of the future wood energy utilization in Brazil.« less

Projected wood energy impact on US forest wood resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skog, K.E.

1993-12-31

The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price ofmore » wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).« less

Forest Resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-06-01

Forest biomass is an abundant biomass feedstock that complements the conventional forest use of wood for paper and wood materials. It may be utilized for bioenergy production, such as heat and electricity, as well as for biofuels and a variety of bioproducts, such as industrial chemicals, textiles, and other renewable materials. The resources within the 2016 Billion-Ton Report include primary forest resources, which are taken directly from timberland-only forests, removed from the land, and taken to the roadside.

Raman imaging to investigate ultrastructure and composition of plant cell walls : distribution of lignin and cellulose in black spruce wood (Picea mariana)

Treesearch

Umesh P. Agarwal

2006-01-01

A detailed understanding of the structural organization of the cell wall of vascular plants is important from both the perspectives of plant biology and chemistry and of commercial utilization. A state-of-the-art 633-nm laser-based confocal Raman microscope was used to determine the distribution of cell wall components in the cross section of black spruce wood in situ...

Volume and weight characteristics of a typical Douglas-fir/ western larch stand, Coram Experimental Forest, Montana

Treesearch

Robert E. Benson; Joyce A. Schlieter

1980-01-01

An over-mature Douglas-fir/western larch stand on the Coram Experimental Forest in Montana averaged about 7,300 ft3/acre (511 rn3/ha) of wood over 3 inches (7.62 cm) in diameter, and an additional 57 tons/acre (128/ha) of fine material, before harvest. After logging, using three different cutting methods and four different levels of utilization, wood residues ranged...

The fine scale physical attributes of coarse woody debris and effects of surrounding stand structure on its utilization by ants (Hymenoptera: Formicidae) in British Columbia, Canada

Treesearch

Robert J. Higgins; B. Staffan Lindgren

2006-01-01

Coarse woody debris (CWD) is increasingly recognized in Canada for its contribution toward biodiversity. It is a particularly vital resource in subboreal forests as nesting habitat for ants (Formicidae). Wood, which has low specific heat, provides a thermally favorable environment in this cool climate. Ants contribute to the physical breakdown of wood, and colonies are...

Functional lignocellulosic material for the remediation of copper(II) ions from water: Towards the design of a wood filter.

PubMed

Vitas, Selin; Keplinger, Tobias; Reichholf, Nico; Figi, Renato; Cabane, Etienne

2018-05-09

In this study, the chemical modification of bulk beech wood is described along with its utilization as biosorbent for the remediation of copper from water. The material was prepared by esterification using anhydrides, and reaction conditions were optimized to propose a greener process, in particular by reducing the amount of solvent. This modification yields a lignocellulosic material whose native structure is preserved, with an increased amount of carboxylic groups (up to 3 mmol/g). We demonstrate that the material can remove up to 95% of copper from low concentration solutions (100- 500 ppm). The adsorption efficiency decreases with concentrated copper solutions, and we show that a limited number of -COOH groups participate in copper binding (ca. 0.1 Cu/-COOH). This result suggests a limited accessibility of -COOH groups in the wood scaffold. This was demonstrated by the characterization of -COOH and copper distributions inside wood. Raman and EDX imaging confirmed that most -COOH groups are located inside the wood cell walls, thereby limiting interactions with copper. According to this study, critical limitations of bulk wood as a biosorbent were identified, and the results will be used to improve the material and design an efficient wood filter for heavy metal remediation. Copyright © 2018 Elsevier B.V. All rights reserved.

Utilizing Municipal Trees: Ideas From Across the Country

Treesearch

Stephen M. Bratkovich

2001-01-01

To show how municipal tree removals can be utilized for traditional wood products, this publication highlights 16 successful projects from around the country. These case studies are organized by the different types of participants: State and regional partnerships, municipalities, tree service firms, entrepreneurs, and sawmills. Contact information is provided for each...

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED REAR DOOR, AND ROW OF 6-LIGHT OVER 1-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS AROUND EAST CORNER OF HOUSE. VIEW TO EAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

11. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN DOORWAY TO LIVING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN DOORWAY TO LIVING ROOM, AND BUILT-IN CABINETS AROUND SINK AND 3-LIGHT OVER 3-LIGHT, DOUBLE-HUNG, WOOD-FRAME WINDOW. VIEW TO NORTHWEST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

KSC-02pd0430

NASA Image and Video Library

2002-03-29

KENNEDY SPACE CENTER, FLA. -- This Red-Shouldered Hawk, perched on a utility pole at Kennedy Space Center, keeps an eye out for prey. Ranging from Central to South Florida, its diet includes rodents, lizards and insects. Its habitat is chiefly cypress and mangrove swamps

Chemical composition and physical properties of filter fly ashes from eight grate-fired biomass combustion plants.

PubMed

Lanzerstorfer, Christof

2015-04-01

For the handling, treatment and utilization of fly ash from biomass combustion its chemical composition and physical properties are important. In this study eight filter fly ashes from different grate-fired biomass combustion plants were investigated. In fly ash from straw combustion high concentrations of (K) were found, whereas in the fly ash from wood combustion the concentrations of Ca and Mg were higher. The average concentration of PO4(3-) was similar in both types of fly ashes. In all wood fly ashes some measured heavy metal concentrations were above the limits for utilization. The straw fly ashes were much less contaminated and can be utilized. For wood fly ash most parameters showed little variation, except from one fly ash where the dust pre-separator is in poor condition. The average values were: mass median diameter 4.3±0.8 μm, spread of particle size distribution 19±11, particle density 2620±80 kg/m3 and angle of repose 50°±1°. The density of the straw fly ashes is lower (2260±80 kg/m3) and the spread of the size distribution is higher (72±24). For one straw combustion fly ash the values of the mass median diameter and the angle of repose were similar to the values of wood combustion fly ash, for the other straw fly ash the values differed considerably. While the particle size of this fly ash was much smaller, surprisingly the angle of repose was also lower. This can be attributed to the formation of small agglomerates in this fly ash, which were not disintegrated without a certain stress. Copyright © 2015. Published by Elsevier B.V.

Analyzing the feasibility of utilizing small diameter hardwood timber for solid wood products and residues

Treesearch

Brian Perkins; Bob Smith; Philip Araman

2008-01-01

The eastern hardwood forest contains small diameter timber that is often of lower quality and lower value than larger sawtimber. This small diameter hardwood timber has traditionally been utilized for pulpwood, but it can also be used for lumber and residue production. In order to increase the utilization of this resource by sawmills, a number of analyses need to be...

Dictating anisotropic electric conductivity of a transparent copper nanowire coating by the surface structure of wood.

PubMed

Guo, Huizhang; Büchel, Martin; Li, Xing; Wäckerlin, Aneliia; Chen, Qing; Burgert, Ingo

2018-05-01

In this article, a robust, air-stable, flexible and transparent copper (Cu) nanowire (NW) network coating on the surface of the wood is presented, based on a fusion welding of the Cu NWs by photonic curing. Thereby, an anisotropic conductivity can be achieved, which is originating from the structural organization of the wood body and its surface. Furthermore, the Cu NWs are protected from oxidation or wear by a commercially available paraffin wax-polyolefin, which also results in surface water repellency. The developed processing steps present a facile and flexible routine for applying Cu NW transparent conductors to abundant biomaterials and solve current manufacturing obstacles for corrosion-resistant circuits while keeping the natural appearance of the substrate. It may open a venue for more extensive utilization of materials from renewable resources such as wood for electronic devices in smart buildings or mobility applications. © 2018 The Author(s).

Foundation Elements for Naval Low-Rise Buildings

DTIC Science & Technology

2009-10-01

of < 2% by total mass (oven dry weight) using a steam tube dryer . Wood flour, polymer, and lubricants were then mixed in a low intensity blender...Allendale, NJ) was employed for HDPE blends. Specific formulations for each composite are outlined in Table 1. A steam tube dryer was utilized to reduce...materials were weighed and dry-blended in 350lb batches prior to profile extrusion. The wood flour was first dried with a steam tube dryer to a moisture

Criterion 6, indicator 33 : recovery or recycling of forest products as a percentage of total forest products consumption

Treesearch

Ken Skog; James Howard; Rebecca Westby

2011-01-01

This indicator shows the trend in recovering wood and paper for reuse in products in the United States. This reuse can hold down the need to harvest wood to meet U.S. consumption needs. The paper recycling rate (utilization rate in producing new paper) increased from 22% to 38% between 1970 and 1996, but then stabilized at 37% to 38% between 1996 and 2006. This rate...

Effects of pex1 disruption on wood lignin biodegradation, fruiting development and the utilization of carbon sources in the white-rot Agaricomycete Pleurotus ostreatus and non-wood decaying Coprinopsis cinerea.

PubMed

Nakazawa, Takehito; Izuno, Ayako; Horii, Masato; Kodera, Rina; Nishimura, Hiroshi; Hirayama, Yuichiro; Tsunematsu, Yuta; Miyazaki, Yasumasa; Awano, Tatsuya; Muraguchi, Hajime; Watanabe, Kenji; Sakamoto, Masahiro; Takabe, Keiji; Watanabe, Takashi; Isagi, Yuji; Honda, Yoichi

2017-12-01

Peroxisomes are well-known organelles that are present in most eukaryotic organisms. Mutant phenotypes caused by the malfunction of peroxisomes have been shown in many fungi. However, these have never been investigated in Agaricomycetes, which include white-rot fungi that degrade wood lignin in nature almost exclusively and play an important role in the global carbon cycle. Based on the results of a forward genetics study to identify mutations causing defects in the ligninolytic activity of the white-rot Agaricomycete Pleurotus ostreatus, we report phenotypes of pex1 disruptants in P. ostreatus, which are defective in two major features of white-rot Agaricomycetes: lignin biodegradation and mushroom formation. Pex1 disruption was also shown to cause defects in the hyphal growth of P. ostreatus on certain sawdust and minimum media. We also demonstrated that pex1 is essential for fruiting initiation in the non-wood decaying Agaricomycete Coprinopsis cinerea. However, unlike P. ostreatus, significant defects in hyphal growth on the aforementioned agar medium were not observed in C. cinerea. This result, together with previous C. cinerea genetic studies, suggests that the regulation mechanisms for the utilization of carbon sources are altered during the evolution of Agaricomycetes or Agaricales. Copyright © 2017 Elsevier Inc. All rights reserved.

Release of Arsenic to the Environment from CCA-Treated Wood: Part II – Leaching and Speciation during Disposal

PubMed Central

KHAN, BERNINE I.; JAMBECK, JENNA; SOLO-GABRIELE, HELENA M.; TOWNSEND, TIMOTHY G.; CAI, YONG

2008-01-01

Wood treated with chromated copper arsenate (CCA) is primarily disposed within construction and demolition (C&D) debris landfills, with wood monofills and municipal solid waste (MSW) landfills as alternative disposal options. This study evaluated the extent and speciation of arsenic leaching from landfills containing CCA-treated wood. In control lysimeters where untreated wood was used, DMAA represented the major arsenic species. The dominant arsenic species differed in the lysimeters containing CCA-treated wood, with As(V) greatest in the monofill and C&D lysimeters and As(III) greatest in the MSW lysimeters. In CCA-containing lysimeters, the organoarsenic species MMAA and DMAA were virtually absent in the monofill lysimeter and observed in the C&D and MSW lysimeters. Overall arsenic leaching rate varied for the wood monofill (0.69% per meter of water added), C&D (0.36% per m), and MSW (0.84% per m) lysimeters. Utilizing these rates with annual disposal data, a mathematical model was developed to quantify arsenic leaching from CCA-treated wood disposed to Florida landfills. Model findings showed between 20 to 50 metric tons of arsenic (depending on lysimeter type) had leached prior to 2000 with an expected increase between 350 to 830 metric tons by 2040. Groundwater analysis from 21 Florida C&D landfills suspected of accepting CCA-treated wood showed that groundwater at 3 landfills were characterized by elevated arsenic concentrations with only 1 showing impacts from the C&D waste. The slow release of arsenic from disposed treated wood may account for the lack of significant impact to groundwater near most C&D facilities at this time. However, greater impacts are anticipated in the future given that the maximum releases of arsenic are expected by the year 2100. PMID:16509348

49 CFR 325.33 - Site characteristics; highway operations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Section 325.33 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.33 Site... or utility poles. (2) Rural mailboxes. (3) Traffic railings of any type of construction except solid...

49 CFR 325.33 - Site characteristics; highway operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Section 325.33 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.33 Site... or utility poles. (2) Rural mailboxes. (3) Traffic railings of any type of construction except solid...

49 CFR 325.33 - Site characteristics; highway operations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Section 325.33 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.33 Site... or utility poles. (2) Rural mailboxes. (3) Traffic railings of any type of construction except solid...

49 CFR 325.33 - Site characteristics; highway operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Section 325.33 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.33 Site... or utility poles. (2) Rural mailboxes. (3) Traffic railings of any type of construction except solid...

Investigating the Geomorphic and Ecologic Functions of Wood in Relationship to Habitat Type and Salmonid Redds on a Regulated California River

NASA Astrophysics Data System (ADS)

Senter, A. E.; Pasternack, G. B.

2006-12-01

Most river rehabilitation projects incorporate little to no wood in current designs, and those that do have little science to guide them. The overall goal of this research is to investigate the role of wood in a regulated, mid- sized (where river width is greater than most tree heights), Mediterranean-climate (where smaller, softer-wood trees dominate the landscape) river in order to provide a scientific foundation for the potential use of wood in rehabilitation projects within such systems. Wood structures in the active salmonid spawning reach of the Lower Mokelumne River in Central California were measured, mapped, and described during summer and fall 2006. Digital photos and GPS coordinates were used to establish wood location within the stream channel. Structural morphology was determined by measuring physical properties such as individual diameter and length, orientation to stream flow, and jam dimensions. In addition, qualitative attributes were recorded such as decay class and leaf, limb, bark, and root characteristics. A GIS wood layer will be created and added to a database of existing Mokelumne River GIS layers containing salmonid redd (salmon egg nests) densities, hydraulic conditions associated with individual redds, and sub-reach habitat types. An analysis of wood properties, redd locations and conditions, and habitat types will be used to develop a conceptual model of wood dynamics in relation to salmonid habitat on the Lower Mokelumne River. The primary products of this study will be (1) a scientific conceptual model of the role of wood in regulated gravel reaches of mid-size rivers in Mediterranean California and (2) a decision-making framework that will enable river managers to include scientifically based wood structures into rehabilitation designs, thereby enhancing spawning habitat, stream complexity, and biological diversity. These tools will be developed in collaboration with East Bay Municipal Utilities District to aid in the continuing rehabilitation of the Lower Mokelumne River.

Sphenoid dysplasia in neurofibromatosis type 1: a new technique for repair.

PubMed

Concezio, Di Rocco; Amir, Samii; Gianpiero, Tamburrini; Luca, Massimi; Mario, Giordano

2017-06-01

Sphenoid bone dysplasia in neurofibromatosis type 1 is characterized by progressive exophthalmos and facial disfiguration secondary to herniation of meningeal and cerebral structures. We describe a technique for reconstruction of the sphenoid defect apt at preventing or correcting the ocular globe dislocation. After placement of spinal cerebrospinal fluid drainage to reduce intracranial pressure, the temporal pole is posteriorly dislocated extradurally. The greater sphenoid wing defect is identified. A titanium mesh covered by lyophilized dura, modeled in a curved fashion, is interposed between the bone defect and the cerebro-meningeal structures with its convex surface over the retracted temporal pole. The particular configuration of the titanium mesh allows a self-maintaining position due to the pressure exerted by the brain over its convex central part with its lateral margins consequently pushed and self-anchored against the medial and lateral walls of the temporal fossa. Screw fixation is not needed. The technique utilized in four cases proved to be reliable at the long-term clinical and neuroradiological controls (6 to 19 years). Sphenoid bone dysplasia in NF1, resulting in proptosis and exophthalmos, is usually progressive. It can be surgically repaired using a curved titanium mesh with the convexity faced to the temporal pole that is in the opposite fashion from all the techniques previously introduced. When utilized early in life, the technique can prevent the occurrence of the orbital and facial disfiguration.

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, David N.; Emerick, Robert W.; England, Alfred B.

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic compositemore » products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systems—without cell debris removal—is a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for development of useful products using this technology is to scale the technology from the 700-L pilot reactor to a small-scale production facility, with dedicated operation staff and engineering controls. In addition, we recommend that a market study be conducted as well as further product development for construction products that will utilize the unique properties of this bio-based material.« less

Comparative analysis of lignin peroxidase and manganese peroxidase activity on coniferous and deciduous wood using ToF-SIMS.

PubMed

MacDonald, Jacqueline; Goacher, Robyn E; Abou-Zaid, Mamdouh; Master, Emma R

2016-09-01

White-rot fungi are distinguished by their ability to efficiently degrade lignin via lignin-modifying type II peroxidases, including manganese peroxidase (MnP) and lignin peroxidase (LiP). In the present study, time-of flight secondary ion mass spectrometry (ToF-SIMS) was used to evaluate lignin modification in three coniferous and three deciduous wood preparations following treatment with commercial preparations of LiP and MnP from two different white-rot fungi. Percent modification of lignin was calculated as a loss of intact methoxylated lignin over nonfunctionalized aromatic rings, which is consistent with oxidative cleavage of methoxy moieties within the lignin structure. Exposure to MnP resulted in greater modification of lignin in coniferous compared to deciduous wood (28 vs. 18 % modification of lignin); and greater modification of G-lignin compared to S-lignin within the deciduous wood samples (21 vs. 12 %). In contrast, exposure to LiP resulted in similar percent modification of lignin in all wood samples (21 vs 22 %), and of G- and S-lignin within the deciduous wood (22 vs. 23 %). These findings suggest that the selected MnP and LiP may particularly benefit delignification of coniferous and deciduous wood, respectively. Moreover, the current analysis further demonstrates the utility of ToF-SIMS for characterizing enzymatic modification of lignin in wood fibre along with potential advantages over UV and HPCL-MS detection of solubilized delignification products.

Small-scale biomass fueled cogeneration systems - A guidebook for general audiences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiltsee, G.

1993-12-01

What is cogeneration and how does it reduce costs? Cogeneration is the production of power -- and useful heat -- from the same fuel. In a typical biomass-fueled cogeneration plant, a steam turbine drives a generator, producing electricity. The plant uses steam from the turbine for heating, drying, or other uses. The benefits of cogeneration can mostly easily be seen through actual samples. For example, cogeneration fits well with the operation of sawmills. Sawmills can produce more steam from their waste wood than they need for drying lumber. Wood waste is a disposal problem unless the sawmill converts it tomore » energy. The case studies in Section 8 illustrate some pluses and minuses of cogeneration. The electricity from the cogeneration plant can do more than meet the in-house requirements of the mill or manufacturing plant. PURPA -- the Public Utilities Regulatory Policies Act of 1978 -- allows a cogenerator to sell power to a utility and make money on the excess power it produces. It requires the utility to buy the power at a fair price -- the utility`s {open_quotes}avoided cost.{close_quotes} This can help make operation of a cogeneration plant practical.« less

Marketing Wood Products: Unit L#4 Grade 6. Project COULD: Career Orientation Utilizing Language Development.

ERIC Educational Resources Information Center

Coos County Intermediate Education District, North Bend, OR.

Project COULD (Career Orientation Utilizing Language Development) was developed as a means of building skills, knowledges, and attitudes on elementary children's previously acquired backgrounds. Children learn to speak the grammar and vocabulary characteristic of the language heard most frequently at home and in the immediate environment. Each…

Proceedings of papers presented at the 2nd international symposium on applications of biotechnology to tree culture, protection, and utilization.

Treesearch

Charles H. Michler; Michael R. Becwar; Daniel Cullen; Warren L. Nance; Ronald R. Sederoff; James M. Silvicek

1994-01-01

Contains 38 oral presentation abstracts, 34 poster abstracts, and 18 manuscripts on applications of biotechnology to tree research in the areas of stress resistance, protection, and wood utilization presented at an international conference in Bloomington, Minnesota, October 2-6, 1994.

76 FR 23273 - Bend/Ft. Rock Ranger District; Deschutes National Forest; Deschutes County, Oregon; Mt. Bachelor...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-26

... for utilization of wood products from forest management projects and associated economic benefits. 5... only one dedicated hiking trail and one mountain bike trail, located in the base and Nordic areas. Increased hiking and biking infrastructure is needed to meet demand, increase year-round utilization of...

Utilization of Chinese tallow tree and bagasse for medium density fiberboard

Treesearch

Sangyeob Lee; Todd F. Shupe; Chung Y. Hse

2004-01-01

The objective of this research was to investigate various adhesive systems and determine the best composite formulation for selected mechanical and physical properties of medium density fiberboard (MDF) made from wood and bagasse fibers. This study investigated opportunities ofbiomass utilization for natural fiber-based composites from agricultural (bagasse) and...

21. INTERIOR OF UTILITY ROOM SHOWING OPEN REAR DOOR AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. INTERIOR OF UTILITY ROOM SHOWING OPEN REAR DOOR AT PHOTO CENTER, PAIRED NARROW 1-LIGHT OVER 1-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS AT PHOTO LEFT. OPEN DOOR AT PHOTO RIGHT LEADS TO BATHROOM. VIEW TO SOUTHWEST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Genetic architecture of wood properties based on association analysis and co-expression networks in white spruce.

PubMed

Lamara, Mebarek; Raherison, Elie; Lenz, Patrick; Beaulieu, Jean; Bousquet, Jean; MacKay, John

2016-04-01

Association studies are widely utilized to analyze complex traits but their ability to disclose genetic architectures is often limited by statistical constraints, and functional insights are usually minimal in nonmodel organisms like forest trees. We developed an approach to integrate association mapping results with co-expression networks. We tested single nucleotide polymorphisms (SNPs) in 2652 candidate genes for statistical associations with wood density, stiffness, microfibril angle and ring width in a population of 1694 white spruce trees (Picea glauca). Associations mapping identified 229-292 genes per wood trait using a statistical significance level of P < 0.05 to maximize discovery. Over-representation of genes associated for nearly all traits was found in a xylem preferential co-expression group developed in independent experiments. A xylem co-expression network was reconstructed with 180 wood associated genes and several known MYB and NAC regulators were identified as network hubs. The network revealed a link between the gene PgNAC8, wood stiffness and microfibril angle, as well as considerable within-season variation for both genetic control of wood traits and gene expression. Trait associations were distributed throughout the network suggesting complex interactions and pleiotropic effects. Our findings indicate that integration of association mapping and co-expression networks enhances our understanding of complex wood traits. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

Development of a low-cost crash cushion using recycled automobile tires

DOT National Transportation Integrated Search

1998-09-01

Approximately 30 percent of all vehicle related fatalities that occur each year are caused by a single vehicle leaving the road and striking a fixed object; the most common objects struck being trees, guardrails, and utility poles. In many cases curr...

Effects of power-line construction on wetland vegetation in Massachusetts, USA

NASA Astrophysics Data System (ADS)

Nickerson, Norton H.; Dobberteen, Ross A.; Jarman, Nancy M.

1989-07-01

Utility rights-of-way corridors through wetland areas generate long-term impacts from construction activities to these valuable ecosystems. Changes to and recovery of the vegetation communities of a cattail marsh, wooded swamp, and shrub/bog wetland were documented through measurements made each growing season for two years prior, five years following, and again on the tenth year after construction of a 345-kV transmission line. While both the cattail marsh and wooded swamp recovered within a few years, measures of plant community composition in the shrub/bog wetland were still lower, compared to controls, after ten years. Long-term investigations such as the one reported here help decrease uncertainty and provide valuable information for future decision making regarding construction of power utility lines through valuable and dwindling wetland resources.

Measurement and calculation of the sound absorption coefficient of pine wood charcoal

NASA Astrophysics Data System (ADS)

Suh, Jae Gap; Baik, Kyung min; Kim, Yong Tae; Jung, Sung Soo

2013-10-01

Although charcoal has been widely utilized for physical therapy and as a deodorant, water purifier, etc. due to its porous features, research on its role as a sound-absorbing material is rarely found. Thus, the sound absorption coefficients of pine wood charcoal were measured using an impedance tube and were compared with the theoretical predictions in the frequency range of 500˜ 5000 Hz. The theory developed in the current study only considers the lowest possible mode propagating along the air channels of the charcoal and shows good agreements with the measurements. As the frequency is increased, the sound absorption coefficients of pine wood charcoals also increase, but are lower than those of other commonly-used sound-absorbing materials.

High-priority lunar landing sites for in situ and sample return studies of polar volatiles

NASA Astrophysics Data System (ADS)

Lemelin, Myriam; Blair, David M.; Roberts, Carolyn E.; Runyon, Kirby D.; Nowka, Daniela; Kring, David A.

2014-10-01

Our understanding of the Moon has advanced greatly over the last several decades thanks to analyses of Apollo samples and lunar meteorites, and recent lunar orbital missions. Notably, it is now thought that the lunar poles may be much more enriched in H2O and other volatile chemical species than the equatorial regions sampled during the Apollo missions. The equatorial regions sampled, themselves, contain more H2O than previously thought. A new lunar mission to a polar region is therefore of great interest; it could provide a measure of the sources and processes that deliver volatiles while also evaluating the potential in situ resource utilization value they may have for human exploration. In this study, we determine the optimal sites for studying lunar volatiles by conducting a quantitative GIS-based spatial analysis of multiple relevant datasets. The datasets include the locations of permanently shadowed regions, thermal analyses of the lunar surface, and hydrogen abundances. We provide maps of the lunar surface showing areas of high scientific interest, including five regions near the lunar north pole and seven regions near the lunar south pole that have the highest scientific potential according to rational search criteria. At two of these sites-a region we call the “Intercrater Polar Highlands” (IPH) near the north pole, and Amundsen crater near the south pole-we provide a more detailed assessment of landing sites, sample locations, and exploration strategies best suited for future human or robotic exploration missions.

14 CFR 23.625 - Fitting factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction § 23.625... test data (such as continuous joints in metal plating, welded joints, and scarf joints in wood). (c...

Ultra-thick, Low-Tortuosity, and Mesoporous Wood Carbon Anode for High-Performance Sodium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, Fei; Luo, Wei; Dai, Jiaqi

Sodium-ion batteries (SIBs) have attracted extensive interest in the past few years because of the low cost and abundance of sodium resources and hence the potential for grid scale energy storage. Developing low cost electrode materials, particularly anode materials, is the key for further promoting the application of SIBs. Here, we for the first time report a self-standing porous carbon anode directly from natural wood for SIBs, which processes following advantages: (i) ultra-thick carbon anode with a high areal capacity, for example a capacity of 13.6 mAh cm-2 was delivered when the thickness reached 0.85 mm; (ii) low tortuosity, wheremore » numerous inherited aligned channels in the wood carbon provide a rapid ion transport path; (iii) porous nature enables a fast ion transfer between the carbon electrode and the electrolyte; (iv) 100% utilization of the wood carbon that conductive additives, binders, and current-collectors are not needed; v) when coupling a Na3V2(PO4)3 cathode with the wood carbon anode, a high capacity of 80 mAh g-1 was obtained at 0.5 C rate (base on cathode) and excellent cycling stability of 300 cycles was also achieved, which demonstrated the promising performance of earth-abundant wood derived carbon material.« less

Identification of wood-boring beetles (Cerambycidae and Buprestidae) intercepted in trade-associated solid wood packaging material using DNA barcoding and morphology.

PubMed

Wu, Yunke; Trepanowski, Nevada F; Molongoski, John J; Reagel, Peter F; Lingafelter, Steven W; Nadel, Hannah; Myers, Scott W; Ray, Ann M

2017-01-16

Global trade facilitates the inadvertent movement of insect pests and subsequent establishment of populations outside their native ranges. Despite phytosanitary measures, nonnative insects arrive at United States (U.S.) ports of entry as larvae in solid wood packaging material (SWPM). Identification of wood-boring larval insects is important for pest risk analysis and management, but is difficult beyond family level due to highly conserved morphology. Therefore, we integrated DNA barcoding and rearing of larvae to identify wood-boring insects in SWPM. From 2012 to 2015, we obtained larvae of 338 longhorned beetles (Cerambycidae) and 38 metallic wood boring beetles (Buprestidae) intercepted in SWPM associated with imported products at six U.S. ports. We identified 265 specimens to species or genus using DNA barcodes. Ninety-three larvae were reared to adults and identified morphologically. No conflict was found between the two approaches, which together identified 275 cerambycids (23 genera) and 16 buprestids (4 genera). Our integrated approach confirmed novel DNA barcodes for seven species (10 specimens) of woodborers not in public databases. This study demonstrates the utility of DNA barcoding as a tool for regulatory agencies. We provide important documentation of potential beetle pests that may cross country borders through the SWPM pathway.

Identification of wood-boring beetles (Cerambycidae and Buprestidae) intercepted in trade-associated solid wood packaging material using DNA barcoding and morphology

PubMed Central

Wu, Yunke; Trepanowski, Nevada F.; Molongoski, John J.; Reagel, Peter F.; Lingafelter, Steven W.; Nadel, Hannah; Myers, Scott W.; Ray, Ann M.

2017-01-01

Global trade facilitates the inadvertent movement of insect pests and subsequent establishment of populations outside their native ranges. Despite phytosanitary measures, nonnative insects arrive at United States (U.S.) ports of entry as larvae in solid wood packaging material (SWPM). Identification of wood-boring larval insects is important for pest risk analysis and management, but is difficult beyond family level due to highly conserved morphology. Therefore, we integrated DNA barcoding and rearing of larvae to identify wood-boring insects in SWPM. From 2012 to 2015, we obtained larvae of 338 longhorned beetles (Cerambycidae) and 38 metallic wood boring beetles (Buprestidae) intercepted in SWPM associated with imported products at six U.S. ports. We identified 265 specimens to species or genus using DNA barcodes. Ninety-three larvae were reared to adults and identified morphologically. No conflict was found between the two approaches, which together identified 275 cerambycids (23 genera) and 16 buprestids (4 genera). Our integrated approach confirmed novel DNA barcodes for seven species (10 specimens) of woodborers not in public databases. This study demonstrates the utility of DNA barcoding as a tool for regulatory agencies. We provide important documentation of potential beetle pests that may cross country borders through the SWPM pathway. PMID:28091577

Support for the Elimination of Roadside Hazards : Evaluating Roadside Collision Data and Clear Zone Requirements

DOT National Transportation Integrated Search

2009-09-01

Over a three year period (2004-2006), there were more than 60,000 crashes involving fixed objects (trees, utility poles, : culverts, bridge piers, etc.) located within South Carolina roadsides. These fixed object crashes accounted for 20% of all cras...

47 CFR 1.1404 - Complaint.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., maintenance, and administrative. These charges may be expressed as a percentage of the net pole investment... state court that determines the treatment of accumulated deferred taxes if it is at issue in the... deferred taxes. (x) The rate of return authorized for the utility for intrastate service. With its pleading...

Identifying wood utilization options for ecosystem management : summary of a national research project

Treesearch

K. E. Skog; R. J. Barbour; J. E. Baumgras; A. Clark

1997-01-01

Using an ecosystem approach to forest management will change silvicultural practices, thus requiring utilization options to provide revenue and to help offset the costs of the silviculture treatments. The Forest Service, university cooperators, and several industry mills in the southern, western, and northeastern United States have been involved in a national...

The next century of wood products utilization : a call for reflection and innovation

Treesearch

John A. Youngquist; Thomas E. Hamilton

1999-01-01

Sustainable development has become the umbrella objective for forest management in many countries of the world, and managers are increasingly faced with the challenges of balancing environmental and economic health in their forest management and resource utilization decisions. It can no longer be assumed that abundant raw materials are available simply for the taking....

A 100 J-level nanosecond DPSSL for high energy density experiments

NASA Astrophysics Data System (ADS)

Butcher, Thomas; Mason, Paul; Banerjee, Saumyabrata; Ertel, Klaus; Phillips, P. Jonathan; Smith, Jodie; De Vido, Mariastefania; Chekhlov, Oleg; Divoky, Martin; Pilat, Jan; Priebe, Gerd; Toncian, Toma; Shaikh, Waseem; Hooker, Chris; Lucianetti, Antonio; Hernandez-Gomez, Cristina; Mocek, Tomas; Edwards, Chris; Collier, John

2017-05-01

We present an overview of the cryo-amplifier concept and design utilized in the DiPOLE100 laser system built for use at the HiLASE Center, which has been successfully tested operating at an average power of 1kW. Following this we describe the alterations made to the design in the second generation system being constructed for high energy density (HED) experiments in the HED beamline at the European XFEL. These changes are predominantly geometric in nature, however also include improved mount design and improved control over the temporal shape of the output pulse. Finally, we comment on future plans for development of the DiPOLE laser amplifier architecture.

Applicability of ion mobility spectrometry for detection of quarantine pests in wood

NASA Astrophysics Data System (ADS)

Ewing, K. J.; Sanghera, J.; Myers, S. W.; Ervin, A. M.; Carey, C.; Gleason, G.; Mosser, L.; Levy, L.; Hennessey, M. K.; Bulluck, R.

2016-05-01

Visual inspection is the most commonly used method for detecting quarantine pests in agricultural cargo items at ports. For example, solid wood packing material (SWPM) at ports may be a pathway for wood pests and is a frequent item of inspection at ports. The inspection process includes examination of the external surface of the item and often destructive sampling to detect internal pest targets. There are few tools available to inspectors to increase the efficiency of inspection and reduce the labor involved. Ion mobility spectrometry (IMS) has promise as an aid for inspection. Because pests emit volatile organic compounds (VOCs) such as hormone like substances, Ion Mobility Spectrometry (IMS) was investigated for possible utility for detecting pests during inspection. SWPM is a major pest pathway in trade, and fumigation of many kinds of wood, including SWPM, with methyl bromide (MeBr) following a published schedule1 is regularly conducted for phytosanitary reasons prior to shipment to the United States. However, the question remains as to how long the methyl bromide remains in the wood samples after fumigation such that it could act as an interferent to the detection of pest related VOC emissions. This work investigates the capability of ion mobility spectrometry to detect the presence of residual methyl bromide in fumigated maple and poplar wood samples at different times post fumigation up to 118 days after fumigation. Data show that MeBr can be detected in the less dense poplar wood up to 118 days after fumigation while MeBr can be detected in the denser maple wood 55 days after fumigation.

Dissection of Insertion–Deletion Variants within Differentially Expressed Genes Involved in Wood Formation in Populus

PubMed Central

Gong, Chenrui; Du, Qingzhang; Xie, Jianbo; Quan, Mingyang; Chen, Beibei; Zhang, Deqiang

2018-01-01

Short insertions and deletions (InDels) are one of the major genetic variants and are distributed widely across the genome; however, few investigations of InDels have been conducted in long-lived perennial plants. Here, we employed a combination of RNA-seq and population resequencing to identify InDels within differentially expressed (DE) genes underlying wood formation in a natural population of Populus tomentosa (435 individuals) and utilized InDel-based association mapping to detect the causal variants under additive, dominance, and epistasis underlying growth and wood properties. In the present paper, 5,482 InDels detected from 629 DE genes showed uneven distributions throughout all 19 chromosomes, and 95.9% of these loci were diallelic InDels. Seventy-four InDels (positive false discovery rate q ≤ 0.10) from 68 genes exhibited significant additive/dominant effects on 10 growth and wood-properties, with an average of 14.7% phenotypic variance explained. Potential pleiotropy was observed in one-third of the InDels (representing 24 genes). Seven genes exhibited significantly differential expression among the genotypic classes of associated InDels, indicating possible important roles for these InDels. Epistasis analysis showed that overlapping interacting genes formed unique interconnected networks for each trait, supporting the putative biochemical links that control quantitative traits. Therefore, the identification and utilization of InDels in trees will be recognized as an effective marker system for molecular marker-assisted breeding applications, and further facilitate our understanding of quantitative genomics. PMID:29403506

Measuring the state of charge of the electrolyte solution in a vanadium redox flow battery using a four-pole cell device

NASA Astrophysics Data System (ADS)

Ngamsai, Kittima; Arpornwichanop, Amornchai

2015-12-01

The decrease in the efficiency and capacity of a vanadium redox flow battery (VRB) caused by an electrolyte imbalance is an important impediment to its long-term operation. Knowing the state of charge (SOC) of an electrolyte solution can quantify the level of the electrolyte imbalance in the VRB. In this study, a four-pole cell device is devised and employed to predict the SOC. The proposed method directly measures the ionic resistance of the electrolyte solution and is sufficiently precise to be applied in real-time mode. Experimental studies on the effects of the operating current on the four-pole cell and the concentrations of vanadium and sulfuric acid in the electrolyte solution are carried out. The results show that the four-pole cell method can be utilized to measure the electrolyte SOC. The concentrations of vanadium and sulfuric acid in the electrolyte solution affect the ionic resistance of the solution. Regarding the capacity and efficiency of the VRB system, the results indicate that the electrical charge is determined from the concentration of vanadium and that the cell voltage depends on the concentration of sulfuric acid in the electrolyte solution. The decreased vanadium concentration and increased sulfuric acid concentration improves the cell voltage efficiency.

A sustainable and resilient approach through biochar addition in wood polymer composites.

PubMed

Das, Oisik; Sarmah, Ajit K; Bhattacharyya, Debes

2015-04-15

Biocomposites have been used for sustainability for a few years now and considerable advancements have been made to perfect the physical and mechanical properties. However, there still remain some considerable disadvantages (such as inferior mechanical strength, thickness swell, and rotting) which restrict their proper utilization in wider markets. Attempts have been made to remedy these drawbacks but still further investigation is required to address all the issues and alleviate as many shortcomings as possible. Additionally, concerns related to landfill gas emission prompted the necessity for effective utilization of organic wastes. Lignocellulosic wastes can be valorized by thermo-chemical conversion to form a carbonaceous and renewable material called biochar. Keeping these two problems in mind, a relatively novel idea is recommended for the manufacture of biocomposites where biochar made from pyrolysis of waste could be added with wood and plastic. It is expected to mitigate the general disadvantages of conventional wood plastic composites (WPCs) and at the same time manage landfill wastes giving rise to a potential new breed of improved next generation biocomposites. Furthermore, a 'resilient' perspective is conferred where the long term viability of the state-of-the-art product could be ensured. Copyright © 2015 Elsevier B.V. All rights reserved.

Advanced system demonstration for utilization of biomass as an energy source. Technical Appendix J: alternatives studies. Environmental report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCollom, M.

1979-01-01

A comprehensive review of a wide range of alternatives to the proposed action, the commercial demonstration of an industrial cogenerating facility fired with wood fuels is provided. An extensive effort has been devoted to the evaluation of all reasonable alternatives to this project. A number of possible actions were also briefly considered, but, for various reasons, they were found not to be appropriate at present for a commercial-scale demonstration of an alternative energy source. The critical characteristics of the wood-fueled commercial demonstration project at Westbrook are considered to be: industrial cogeneration of power; the production of 510,000 pounds per hourmore » of industrial process steam; the production of approximately twenty-five megawatts of electric generating capacity, some of which would be available to a public utility in southern Maine; and the consumption of 2,000 tons of wood fuel per day. Each of the alternatives examined in this appendix offers a different option for one or several of the characteristics of the project listed above. As a whole, the appendix describes the range of possible actions that the US Department of Energy and its contractors have considered.« less

Demonstration of a 1 MWe biomass power plant at USMC Base Camp Lejeune. Report for July 1994-May 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleland, J.; Purvis, C.R.

1998-06-01

The paper discusses a biomass energy conversion project being sponsored by EPA to demonstrate an enviromentally and economically sound electrical power option for government installations, industrial sites, rural cooperatives, small municipalities, and developing countries. Wood gasification combined with internal combustion engines was chosen because of (1) recent improvements in gas cleaning, (2) simple economical operation for units < 10 MW, and (3) the option of a clean cheap fuel for the many existing facilities generating expensive electricity from petroleum fuels with reciprocating engines. The plant incorporates a downdraft, moving-bed gasifier utilizing hogged waste wood from the Marine Corps Base atmore » Camp Lejeune, NC. A moving-bed bulk wood dryer and both spark ignition and diesel engines are included. Unique process design features are described briefly, relative to the gasifier, wood drying, tar separation, and process control. A test plan for process optimization and demonstration of reliability, economics, and environmental impact is outlined.« less

Basic research for the geodynamics program

NASA Technical Reports Server (NTRS)

1984-01-01

Some objectives of this geodynamic program are: (1) optimal utilization of laser and VLBI observations as reference frames for geodynamics, (2) utilization of range difference observations in geodynamics, and (3) estimation techniques in crustal deformation analysis. The determination of Earth rotation parameters from different space geodetic systems is studied. Also reported on is the utilization of simultaneous laser range differences for the determination of baseline variation. An algorithm for the analysis of regional or local crustal deformation measurements is proposed along with other techniques and testing procedures. Some results of the reference from comparisons in terms of the pole coordinates from different techniques are presented.

47 CFR 1.1420 - Timeline for access to utility poles.

Code of Federal Regulations, 2011 CFR

2011-10-01

... estimate of charges to perform all necessary make-ready work within 14 days of providing the response... estimate of charges to perform make-ready work beginning 14 days after the estimate is presented. (2) A...-ready procedure. (2) For wireless attachments above the communications space, the notice shall: (i...

46 CFR 120.220 - General safety provisions.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., including switches, fuses, lampholders, etc., must be suitable for the voltage and current utilized. (c) Receptacle outlets of the type providing a grounded pole or a specific direct current polarity must be of a configuration that will not permit improper connection. (d) All electrical equipment and circuits must be...

46 CFR 120.220 - General safety provisions.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., including switches, fuses, lampholders, etc., must be suitable for the voltage and current utilized. (c) Receptacle outlets of the type providing a grounded pole or a specific direct current polarity must be of a configuration that will not permit improper connection. (d) All electrical equipment and circuits must be...

78 FR 69742 - Agency Information Collection Activities: Request for Comments for a New Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-20

... the use of electronic technology, without reducing the quality of the collected information. All... roadside trees and utility poles and other fixed objects; and lessons learned. In addition to State... identify areas along interstate highways that would enhance forest health, improve and enhance aesthetics...

Seventy-five years of masting and rodent population peaks in Norway: Why do wood mice not follow the rules?

PubMed

Selås, Vidar

2016-09-01

Wood mouse (Apodemus sylvaticus) populations are expected to show a peak in autumn in the year after a mast year of sessile oak (Quercus petraea), because stored acorns increase winter survival. In Aust-Agder, South Norway, only 16 of 34 mast years from 1939-2014 were followed by a year with a peak in the wood mouse population. For many of the remaining instances, there rather was a minor peak 2 or 3 years after the mast. In multiple logistic regression models, the probability of a wood mouse population peak after a mast year of sessile oak was positively related to a snow-corrected temperature index of the previous winter and negatively to a small rodent population index of the previous autumn. The present study thus supports the hypothesis that longer periods with snow-free ground and subzero temperatures negatively affect wood mouse winter survival. Because it may be difficult for wood mice to survive on a diet consisting of acorns alone, the negative relationship with the rodent population index of the previous year is most likely caused by an over-exploitation of necessary alternative food resources, such as other plant seeds and arthropods. Stored acorns not utilized during one winter are assumed to benefit wood mice in a succeeding winter, giving a delayed population peak relative to the mast year. © 2016 International Society of Zoological Sciences, Institute of Zoology/Chinese Academy of Sciences and John Wiley & Sons Australia, Ltd.

78 FR 24716 - Information Collection: Disposal of Mineral Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

... petrified wood and common varieties of sand, stone, gravel, pumice, pumicite, cinders, clay, and other... validity of the methodology and assumptions used; (3) ways to enhance the quality, utility, and clarity of...

Mechanical, Thermomechanical and Reprocessing Behavior of Green Composites from Biodegradable Polymer and Wood Flour

PubMed Central

Morreale, Marco; Liga, Antonio; Mistretta, Maria Chiara; Ascione, Laura; La Mantia, Francesco Paolo

2015-01-01

The rising concerns in terms of environmental protection and the search for more versatile polymer-based materials have led to an increasing interest in the use of polymer composites filled with natural organic fillers (biodegradable and/or coming from renewable resources) as a replacement for traditional mineral inorganic fillers. At the same time, the recycling of polymers is still of fundamental importance in order to optimize the utilization of available resources, reducing the environmental impact related to the life cycle of polymer-based items. Green composites from biopolymer matrix and wood flour were prepared and the investigation focused on several issues, such as the effect of reprocessing on the matrix properties, wood flour loading effects on virgin and reprocessed biopolymer, and wood flour effects on material reprocessability. Tensile, Dynamic-mechanical thermal (DMTA), differential scanning calorimetry (DSC) and creep tests were performed, pointing out that wood flour leads to an improvement of rigidity and creep resistance in comparison to the pristine polymer, without compromising other properties such as the tensile strength. The biopolymer also showed a good resistance to multiple reprocessing; the latter even allowed for improving some properties of the obtained green composites. PMID:28793656

The wood frog (Rana sylvatica): a technical conservation assessment

USGS Publications Warehouse

Muths, E.; Rittmann, S.; Irwin, J.; Keinath, D.; Scherer, R.

2005-01-01

Overall, the wood frog (Rana sylvatica) is ranked G5, secure through most of its range (NatureServe Explorer 2002). However, it is more vulnerable in some states within the USDA Forest Service Region 2: S3 (vulnerable) in Colorado, S2 (imperiled) in Wyoming, and S1 (critically imperiled in South Dakota (NatureServe Explorer 2002); there are no records for wood frogs in Kansas or Nebraska. Primary threats to wood frog populations are habitat fragmentation (loss of area, edge effects, and isolation) and habitat loss due to anthropogenic causes (e.g., wetland draining, grazing) and natural changes as habitat succession occurs. Wood frogs are most conspicuous at breeding sites early in the spring, when snow and ice are often still present at pond margins. They tolerate frezzing and hibernate terrestrially in shallow depressions, under leaf litter, grasses, logs, or rocks (Bagdonas 1968, Bellis 1961a); there are no reports of aquatic hibernation for this species (Licht 1991, Pinder et al. 1992). Wood frogs require semi-permanent and temporary pools of natural origin and adjacent wet meadows, and landscape alterations that shorten the hydroperiod of ponds can result in catastrophic tadpole mortality. Plant communities utilized by wood frogs in the Rocky Mountains are hydric to mesic and include sedge and grass meadows, willow hummocks, aspen groves, lodgepole pine forests, and woodlands with leaf litter and/or herbaceous understory (Maslin 1947, Bellis 1961a, Roberts and Lewin 1979, Haynes and Aird 1981). Wood frogs are likely to disperse into surrounding marsh and woodlands soon after oviposition (Heatwole 1961, Haynes and Aird 1981). In the arly fall, wood frogs begin to seek hibernacula at or just below the ground surface, generally in upland forest habitat (Regosin et al. 2003). Licht (1991) demonstrated shelter-seeking behavior at 1.5 [degrees] C. Once they have concealed themselves for hibernation, wood frogs are very difficult to detecta?|

Avian utilization of subsidence wetlands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nawrot, J.R.; Conley, P.S.; Smout, C.L.

1995-09-01

Diverse and productive wetlands have resulted from coal mining in the midwest. The trend from surface to underground mining has increased the potential for subsidence. Planned subsidence of longwall mining areas provides increased opportunities for wetland habitat establishment. Planned subsidence over a 180 meter (590 foot) deep longwall mine in southern Illinois during 1984 to 1986 produced three subsidence wetlands totaling 15 hectares (38 acres). The resulting palustrine emergent wetlands enhanced habitat diversity within the surrounding palustrine forested unsubsided area. Habitat assessments and evaluations of avian utilization of the subsidence wetlands were conducted during February 1990 through October 1991. Avianmore » utilization was greatest within the subsided wetlands. Fifty-three bird species representing seven foraging guilds utilized the subsidence wetlands. Wading/fishing, dabbling waterfowl, and insectivorous avian guilds dominated the subsidence wetlands. The subsidence wetlands represented ideal habitat for wood ducks and great blue herons which utilized snags adjacent to and within the wetlands for nesting (19 great blue heron nests produced 25 young). Dense cover and a rich supply of macroinvertebrates provide excellent brood habitat for wood ducks, while herpetofauna and ichthyofauna provided abundant forage in shallow water zones for great blue herons and other wetland wading birds. The diversity of game and non-game avifauna utilizing the subsidence areas demonstrated the unique value of these wetlands. Preplanned subsidence wetlands can help mitigate loss of wetland habitats in the midwest.« less

Mill demonstration of TMP production from forest thinnings : pulp quality, refining energy, and handsheet properties

Treesearch

J.Y. Zhu; C. Tim Scott; Roland Gleisner; Doreen Mann; D.P. Dykstra; G. Holton Quinn; Louis L. Edwards

2007-01-01

High-value, large-volume utilization of forest thinning materials from U.S. National Forests is a potentially important contributor to sustainable forest health. This study demonstrated the utilization of wood chips produced from thinnings for the production of thermomechanical pulp (TMP). Both whole-log chips (primarily from small-diameter logs, tops, and reject logs...

Mill demonstration of TMP production from forest thinnings: pulp quality, refining energy, and handsheet properties

Treesearch

J.Y. Zhu; C. Tim Scott; Roland Gleisner; Doreen Mann; D.P. Dykstra; G. Holton Quinn; Louis L. Edwards

2007-01-01

High-value, large-volume utilization of forest thinning materials from U.S. national forests is a potentially important contributor to sustainable forest health. This study demonstrated the utilization of wood chips produced from thinnings for the production of thermomechanical pulp (TMP). Both whole-log chips (primarily from small-diameter logs, tops, and reject logs...

Logging residues under different stand and harvesting conditions, Rocky Mountains

Treesearch

Robert E. Benson; Cameron M. Johnston

1976-01-01

Volume and characteristics of logging residues from 34 harvest areas are presented. Clearcuts and partial cuts logged to conventional utilization levels and to close utilization levels are included. Residue volumes ranged from almost 3, 600 ft3 /acre of wood 3-inches-plus down to about 550 ft3 /acre, depending on treatment. More than 60 percent of the residues were...

Production of high concentrated cellulosic ethanol by acetone/water oxidized pretreated beech wood.

PubMed

Katsimpouras, Constantinos; Kalogiannis, Konstantinos G; Kalogianni, Aggeliki; Lappas, Angelos A; Topakas, Evangelos

2017-01-01

Lignocellulosic biomass is an abundant and inexpensive resource for biofuel production. Alongside its biotechnological conversion, pretreatment is essential to enable efficient enzymatic hydrolysis by making cellulose susceptible to cellulases. Wet oxidation of biomass, such as acetone/water oxidation, that employs hot acetone, water, and oxygen, has been found to be an attractive pretreatment method for removing lignin while producing less degradation products. The remaining enriched cellulose fraction has the potential to be utilized under high gravity enzymatic saccharification and fermentation processes for the cost-competing production of bioethanol. Beech wood residual biomass was pretreated following an acetone/water oxidation process aiming at the production of high concentration of cellulosic ethanol. The effect of pressure, reaction time, temperature, and acetone-to-water ratio on the final composition of the pretreated samples was studied for the efficient utilization of the lignocellulosic feedstock. The optimal conditions were acetone/water ratio 1:1, 40 atm initial pressure of 40 vol% O 2 gas, and 64 atm at reaction temperature of 175 °C for 2 h incubation. The pretreated beech wood underwent an optimization step studying the effect of enzyme loading and solids content on the enzymatic liquefaction/saccharification prior to fermentation. In a custom designed free-fall mixer at 50 °C for either 6 or 12 h of prehydrolysis using an enzyme loading of 9 mg/g dry matter at 20 wt% initial solids content, high ethanol concentration of 75.9 g/L was obtained. The optimization of the pretreatment process allowed the efficient utilization of beech wood residual biomass for the production of high concentrations of cellulosic ethanol, while obtaining lignin that can be upgraded towards high-added-value chemicals. The threshold of 4 wt% ethanol concentration that is required for the sustainable bioethanol production was surpassed almost twofold, underpinning the efficient conversion of biomass to ethanol and bio-based chemicals on behalf of the biorefinery concept.

Wear Testing of the HERMeS Thruster

NASA Technical Reports Server (NTRS)

Williams, George J., Jr.; Gilland, James H.; Peterson, Peter Y.; Kamhawi, Hani; Huang, Wensheng; Ahern, Drew M.; Yim, John; Herman, Daniel A.; Hofer, Richard R.; Sekerak, Michael

2016-01-01

The Hall-Effect Rocket with Magnetic Shielding (HERMeS) thruster is being developed and tested at NASA GRC and NASA JPL through support of the Space Technology Mission Directorate (STMD) as primary propulsion for the Asteroid Redirect Robotic Mission (ARRM). This thruster is advancing the state-of-the-art of Hall-effect thrusters and is intended to serve as a precursor to higher power systems for human interplanetary exploration. A 2000-hour wear test has been initiated at NASA GRC with the HERMeS Technology Demonstration Unit One and three of four test segments have been completed totaling 728 h of operation. This is the first test of a NASA-designed magnetically shielded thruster to extend beyond 300 hr of continuous operation. Trends in performance, component wear, thermal design, plume properties, and back-sputtered deposition are discussed for two wear-test segments of 246 h and 360 h. The first incorporated graphite pole covers in an electrical configuration where cathode was electrically connected to thruster body. The second utilized traditional alumina pole covers with the thruster body floating. It was shown that the magnetic shielding in both configurations completely eliminated erosion of the boron nitride discharge channel but resulted in erosion of the inner pole cover. The volumetric erosion rate of the graphite pole covers was roughly 2/3 that of the alumina pole covers and the thruster exhibited slightly better performance. Buildup of back-sputtered carbon on the BN channel at a rate of roughly 1.5 µm/kh is shown to have negligible impact on the performance.

Texture and anisotropy in ferroelectric lead metaniobate

NASA Astrophysics Data System (ADS)

Iverson, Benjamin John

Ferroelectric lead metaniobate, PbNb2O6, is a piezoelectric ceramic typically used because of its elevated Curie temperature and anisotropic properties. However, the piezoelectric constant, d33, is relatively low in randomly oriented ceramics when compared to other ferroelectrics. Crystallographic texturing is often employed to increase the piezoelectric constant because the spontaneous polarization axes of grains are better aligned. In this research, crystallographic textures induced through tape casting are distinguished from textures induced through electrical poling. Texture is described using multiple quantitative approaches utilizing X-ray and neutron time-of-flight diffraction. Tape casting lead metaniobate with an inclusion of acicular template particles induces an orthotropic texture distribution. Templated grain growth from seed particles oriented during casting results in anisotropic grain structures. The degree of preferred orientation is directly linked to the shear behavior of the tape cast slurry. Increases in template concentration, slurry viscosity, and casting velocity lead to larger textures by inducing more particle orientation in the tape casting plane. The maximum 010 texture distributions were two and a half multiples of a random distribution. Ferroelectric texture was induced by electrical poling. Electric poling increases the volume of material oriented with the spontaneous polarization direction in the material. Samples with an initial paraelectric texture exhibit a greater change in the domain volume fraction during electrical poling than randomly oriented ceramics. In tape cast samples, the resulting piezoelectric response is proportional to the 010 texture present prior to poling. This results in property anisotropy dependent on initial texture. Piezoelectric properties measured on the most textured ceramics were similar to those obtained with a commercial standard.

Biomechanical Strength of Retrograde Fixation in Proximal Third Scaphoid Fractures.

PubMed

Daly, Charles A; Boden, Allison L; Hutton, William C; Gottschalk, Michael B

2018-04-01

Current techniques for fixation of proximal pole scaphoid fractures utilize antegrade fixation via a dorsal approach endangering the delicate vascular supply of the dorsal scaphoid. Volar and dorsal approaches demonstrate equivalent clinical outcomes in scaphoid wrist fractures, but no study has evaluated the biomechanical strength for fractures of the proximal pole. This study compares biomechanical strength of antegrade and retrograde fixation for fractures of the proximal pole of the scaphoid. A simulated proximal pole scaphoid fracture was produced in 22 matched cadaveric scaphoids, which were then assigned randomly to either antegrade or retrograde fixation with a cannulated headless compression screw. Cyclic loading and load to failure testing were performed and screw length, number of cycles, and maximum load sustained were recorded. There were no significant differences in average screw length (25.5 mm vs 25.6 mm, P = .934), average number of cyclic loading cycles (3738 vs 3847, P = .552), average load to failure (348 N vs 371 N, P = .357), and number of catastrophic failures observed between the antegrade and retrograde fixation groups (3 in each). Practical equivalence between the 2 groups was calculated and the 2 groups were demonstrated to be practically equivalent (upper threshold P = .010). For this model of proximal pole scaphoid wrist fractures, antegrade and retrograde screw configuration have been proven to be equivalent in terms of biomechanical strength. With further clinical study, we hope surgeons will be able to make their decision for fixation technique based on approaches to bone grafting, concern for tenuous blood supply, and surgeon preference without fear of poor biomechanical properties.

KSC-2011-5979

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods

KSC-2011-5978

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods

Silicified wood from the Permian and Triassic of Antarctica: Tree rings from polar paleolatitudes

USGS Publications Warehouse

Ryberg, P.E.; Taylor, E.L.

2007-01-01

The mass extinction at the Permian-Triassic boundary produced a floral turnover in Gondwana in which Paleozoic seed ferns belonging to the Glossopteridales were replaced by corystosperm seed ferns and other seed plant groups in the Mesozoic. Secondary growth (wood production) in both plant groups provides information on plant growth in relation to environment in the form of permineralized tree rings. Techniques utilized to analyze extant wood can be used on fossil specimens to better understand the climate from both of these periods. Late Permian and early Middle Triassic tree rings from the Beardmore Glacier area indicate an environment where extensive plant growth occurred at polar latitudes (~80–85°S, Permian; ~75°S, Triassic). A rapid transition to dormancy in both the Permian and Triassic woods suggests a strong influence of the annual light/dark cycle within the Antarctic Circle on ring production. Latewood production in each ring was most likely triggered by the movement of the already low-angled sun below the horizon. The plants which produced the wood have been reconstructed as seasonally deciduous, based on structural and sedimentologic evidence. Although the Late Permian climate has been reconstructed as cold temperate and the Middle Triassic as a greenhouse, these differences are not reflected in tree ring anatomy or wood production in these plant fossils from the central Transantarctic Mountains.

75 FR 53892 - Action To Ensure Authority To Issue Permits Under the Prevention of Significant Deterioration...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-02

... NAICS \\a\\ Utilities (electric, natural gas, other 2211, 2212, 2213. systems). Manufacturing (food, beverages, 311, 312, 313, 314, 315, 316. tobacco, textiles, leather). Wood product, paper manufacturing...

Treated wood preservatives linked to aquatic damage, human illness, and death--a societal problem.

PubMed

Edlich, Richard F; Winters, Kathryne L; Long, William B

2005-01-01

On February 12, 2002, the US Environmental Protection Agency (EPA) announced a voluntary decision by industry to move consumer use of treated lumber products away from a variety of pressure-treated wood that contains arsenate (As) by December 31, 2003, in favor of new alternative wood preservatives. Chromated copper arsenate (CCA) is a chemical mixture consisting of three pesticidal compounds (As, chromium, and copper) registered for wood preservative uses. CCA is injected into wood by a process that uses high pressure to saturate wood products with the chemical. Only people who have received the proper safety training should use CCA to treat wood products. Around the home, CCA-treated wood is commonly used for decks, walkways, fences, gazebos, boat docks, and playground equipment. Other common uses of CCA-treated wood include highway noise barriers, sign posts, utility posts, and retaining walls. As of January 1, 2004, the EPA is no longer allowing CCA products to be used to treat wood intended for any of these residential uses. This decision will facilitate the voluntary transition to new alternative wood preservatives that do not contain As in both the manufacturing and retail sectors. To its credit, the EPA has developed consumer safety information sheets, hanging signs, end signs, and bin stickers that provide comprehensive information about the dangers of CCA-treated wood, use-site, and handling precautions. The EPA has not concluded that CCA-treated wood poses any unreasonable risk to the public or the environment. Nevertheless, As is a known human carcinogen and, thus, the EPA believes that any reduction in the levels of potential exposure to As is desirable. The toxicologic manifestations have been primarily related to the effects of As exposure from drinking water sources and include the following: acute poisoning incidents, cardiovascular effects, diabetes mellitus, and cancer. Understanding the biomethylation of As is central to elucidating its action as a toxin and a carcinogen. In humans as in many other species, inorganic As is enzymatically converted to the methylated products methyl As (MAs) and dimethyl As (DMAs). The aforementioned voluntary agreement to reduce the uses of CCA-treated wood does not include a ban on the use of CCA for residential roofing. A major reason that this wood product should be banned from residential roofing is that it does not provide a Class "A" fire-rated roof system, which markedly reduce the frequency of residential roof fires.

Agile: From Software to Mission System

NASA Technical Reports Server (NTRS)

Trimble, Jay; Shirley, Mark H.; Hobart, Sarah Groves

2016-01-01

The Resource Prospector (RP) is an in-situ resource utilization (ISRU) technology demonstration mission, designed to search for volatiles at the Lunar South Pole. This is NASA's first near real time tele-operated rover on the Moon. The primary objective is to search for volatiles at one of the Lunar Poles. The combination of short mission duration, a solar powered rover, and the requirement to explore shadowed regions makes for an operationally challenging mission. To maximize efficiency and flexibility in Mission System design and thus to improve the performance and reliability of the resulting Mission System, we are tailoring Agile principles that we have used effectively in ground data system software development and applying those principles to the design of elements of the mission operations system.

Variable gas leak rate valve

DOEpatents

Eernisse, Errol P.; Peterson, Gary D.

1976-01-01

A variable gas leak rate valve which utilizes a poled piezoelectric element to control opening and closing of the valve. The gas flow may be around a cylindrical rod with a tubular piezoelectric member encircling the rod for seating thereagainst to block passage of gas and for reopening thereof upon application of suitable electrical fields.

Selection of High-Redshift QSOs using Subaru and CFHT Photometry

NASA Astrophysics Data System (ADS)

Jones, Victoria; White, Cameron; Hasinger, Guenther; Hu, Esther

2018-01-01

We present 31 high redshift (5.0 ≤ z ≤ 6.0) quasar candidates using photometry from the Subaru and Canada France Hawaii telescopes. These candidates were observed as part of the Hawaii EROsita Ecliptic Pole Survey (HEROES) of the North Ecliptic Pole in 2016 and again in 2017. The ongoing HEROES survey is gathering ground-based imaging data in preparation for the eROSITA X-Ray mission. For this selection, we utilized optical-near IR imaging data of a 36 square degree field in one narrowband and five broadband filters on Subaru’s Hyper Suprime-Cam (HSC). We also utilized less complete coverage of the field in the U and J bands from CFHT’s MegaCam and WIRCam respectively. Photometric redshifts were calculated using SED fitting techniques in comparison with stellar, quasar, and galaxy models. Selections were then made through extendedness cuts, color-color comparisons, and color-redshift plots. Follow-up spectroscopic observations of these candidates with the DEIMOS spectrograph on Keck and X-Ray observations with eROSITA in the coming years will allow for reliable classifications of our selected candidates.

Single-step collision-free trajectory planning of biped climbing robots in spatial trusses.

PubMed

Zhu, Haifei; Guan, Yisheng; Chen, Shengjun; Su, Manjia; Zhang, Hong

For a biped climbing robot with dual grippers to climb poles, trusses or trees, feasible collision-free climbing motion is inevitable and essential. In this paper, we utilize the sampling-based algorithm, Bi-RRT, to plan single-step collision-free motion for biped climbing robots in spatial trusses. To deal with the orientation limit of a 5-DoF biped climbing robot, a new state representation along with corresponding operations including sampling, metric calculation and interpolation is presented. A simple but effective model of a biped climbing robot in trusses is proposed, through which the motion planning of one climbing cycle is transformed to that of a manipulator. In addition, the pre- and post-processes are introduced to expedite the convergence of the Bi-RRT algorithm and to ensure the safe motion of the climbing robot near poles as well. The piecewise linear paths are smoothed by utilizing cubic B-spline curve fitting. The effectiveness and efficiency of the presented Bi-RRT algorithm for climbing motion planning are verified by simulations.

Periodic domain inversion in x-cut single-crystal lithium niobate thin film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mackwitz, P., E-mail: peterm@mail.upb.de; Rüsing, M.; Berth, G.

2016-04-11

We report the fabrication of periodically poled domain patterns in x-cut lithium niobate thin-film. Here, thin films on insulator have drawn particular attention due to their intrinsic waveguiding properties offering high mode confinement and smaller devices compared to in-diffused waveguides in bulk material. In contrast to z-cut thin film lithium niobate, the x-cut geometry does not require back electrodes for poling. Further, the x-cut geometry grants direct access to the largest nonlinear and electro-optical tensor element, which overall promises smaller devices. The domain inversion was realized via electric field poling utilizing deposited aluminum top electrodes on a stack of LNmore » thin film/SiO{sub 2} layer/Bulk LN, which were patterned by optical lithography. The periodic domain inversion was verified by non-invasive confocal second harmonic microscopy. Our results show domain patterns in accordance to the electrode mask layout. The second harmonic signatures can be interpreted in terms of spatially, overlapping domain filaments which start their growth on the +z side.« less

[Medical certification in workers involved in logging and wood-processing].

PubMed

Romankow, Jacek

2007-01-01

Activities involved in forestry and woodworking industry are associated with workers being exposed to numerous environmental and technology-related factors that are detrimental to their health. Such hazards include working in changeable climatic conditions, in the vicinity of heavy equipment, exposure to noise, chainsaw vibrations, enforced body positioning, hard physical work, the effect of exhaust gases, potential effects of biological factors, including epizootic diseases. Wood processing involves performing mechanical activities employing tools and machines, as well as processes utilizing various chemical substances. Forestry and woodworking industry workers may deal both with timber and with wood products. In medical certification, the following issues are of significance: work in the vicinity of rotational elements, noise, effects of chemicals or biological factors, including carcinogenic substances. For this reason, the procedures involved in medical examinations of such workers are complex.

Preference of Formosan subterranean termites for blue-stained southern yellow pine sapwood.

PubMed

Little, N S; Blount, N A; Londo, A J; Kitchens, S C; Schultz, T P; McConnell, T E; Riggins, J J

2012-10-01

Little research has been conducted to investigate interactions between the invasive Formosan subterranean termite, Coptotermes formosanus Shiraki, and pine bark beetles native to the southeastern United States. Facilitative interactions between these organisms could alter stand dynamics and impact wood utilization strategies. American Wood Protection Association Standard E1-09 choice tests were carried out to determine the feeding preference of Formosan subterranean termites for blue-stained versus unstained southern yellow pine sapwood. Three separate colonies of Formosan subterranean termites consumed on average twice as much air-dried blue-stained southern yellow pine sapwood over unstained air-dried controls. Additionally, Formosan subterranean termites consumed over five-times more kiln-dried blue-stained sapwood than unstained kiln-dried control wafers. The implications of these results are particularly relevant to pine forest ecology, nutrient cycling, and the utilization of blue-stained southern pine building products in the southeastern United States, where Formosan subterranean termites have become established.

Bycatch in the Maldivian pole-and-line tuna fishery

PubMed Central

Miller, Kelsey I.; Nadheeh, Ibrahim; Jauharee, A. Riyaz; Anderson, R. Charles; Adam, M. Shiham

2017-01-01

Tropical tuna fisheries are among the largest worldwide, with some having significant bycatch issues. However, pole-and-line tuna fisheries are widely believed to have low bycatch rates, although these have rarely been quantified. The Maldives has an important pole-and-line fishery, targeting skipjack tuna (Katsuwonus pelamis). In the Maldives, 106 pole-and-line tuna fishing days were observed between August 2014 and November 2015. During 161 fishing events, tuna catches amounted to 147 t: 72% by weight was skipjack, 25% yellowfin tuna (Thunnus albacares) and 3% other tunas. Bycatch (all non-tuna species caught plus all tuna discards) amounted to 951 kg (0.65% of total tuna catch). Most of the bycatch (95%) was utilized, and some bycatch was released alive, so dead discards were particularly low (0.02% of total tuna catch, or 22 kg per 100 t). Rainbow runner (Elagatis bipinnulata) and dolphinfish (Coryphaena hippurus) together constituted 93% of the bycatch. Live releases included small numbers of silky sharks (Carcharhinus falciformis) and seabirds (noddies, Anous tenuirostris and A. stolidus). Pole-and-line tuna fishing was conducted on free schools and schools associated with various objects (Maldivian anchored fish aggregating devices [aFADs], drifting FADs from western Indian Ocean purse seine fisheries, other drifting objects and seamounts). Free school catches typically included a high proportion of large skipjack and significantly less bycatch. Associated schools produced more variable tuna catches and higher bycatch rates. Fishing trips in the south had significantly lower bycatch rates than those in the north. This study is the first to quantify bycatch rates in the Maldives pole-and-line tuna fishery and the influence of school association on catch composition. Ratio estimator methods suggest roughly 552.6 t of bycatch and 27.9 t of discards are caught annually in the fishery (based on 2015 national catch), much less than other Indian Ocean tuna fisheries, e.g. gillnet, purse-seine, and longline. PMID:28542258

Bycatch in the Maldivian pole-and-line tuna fishery.

PubMed

Miller, Kelsey I; Nadheeh, Ibrahim; Jauharee, A Riyaz; Anderson, R Charles; Adam, M Shiham

2017-01-01

Tropical tuna fisheries are among the largest worldwide, with some having significant bycatch issues. However, pole-and-line tuna fisheries are widely believed to have low bycatch rates, although these have rarely been quantified. The Maldives has an important pole-and-line fishery, targeting skipjack tuna (Katsuwonus pelamis). In the Maldives, 106 pole-and-line tuna fishing days were observed between August 2014 and November 2015. During 161 fishing events, tuna catches amounted to 147 t: 72% by weight was skipjack, 25% yellowfin tuna (Thunnus albacares) and 3% other tunas. Bycatch (all non-tuna species caught plus all tuna discards) amounted to 951 kg (0.65% of total tuna catch). Most of the bycatch (95%) was utilized, and some bycatch was released alive, so dead discards were particularly low (0.02% of total tuna catch, or 22 kg per 100 t). Rainbow runner (Elagatis bipinnulata) and dolphinfish (Coryphaena hippurus) together constituted 93% of the bycatch. Live releases included small numbers of silky sharks (Carcharhinus falciformis) and seabirds (noddies, Anous tenuirostris and A. stolidus). Pole-and-line tuna fishing was conducted on free schools and schools associated with various objects (Maldivian anchored fish aggregating devices [aFADs], drifting FADs from western Indian Ocean purse seine fisheries, other drifting objects and seamounts). Free school catches typically included a high proportion of large skipjack and significantly less bycatch. Associated schools produced more variable tuna catches and higher bycatch rates. Fishing trips in the south had significantly lower bycatch rates than those in the north. This study is the first to quantify bycatch rates in the Maldives pole-and-line tuna fishery and the influence of school association on catch composition. Ratio estimator methods suggest roughly 552.6 t of bycatch and 27.9 t of discards are caught annually in the fishery (based on 2015 national catch), much less than other Indian Ocean tuna fisheries, e.g. gillnet, purse-seine, and longline.

Status and prospects for renewable energy using wood pellets from the southeastern United States

DOE PAGES

Dale, Virginia H.; Kline, Keith L.; Parish, Esther S.; ...

2017-04-20

The ongoing debate about costs and benefits of wood-pellet based bioenergy production in the southeastern United States (SE USA) requires an understanding of the science and context influencing market decisions associated with its sustainability. Production of pellets has garnered much attention as US exports have grown from negligible amounts in the early 2000s to 4.6 million metric tonnes in 2015. Currently, 98% of these pellet exports are shipped to Europe to displace coal in power plants. We ask, 'How is the production of wood pellets in the SE USA affecting forest systems and the ecosystem services they provide?' To addressmore » this question, we review current forest conditions and the status of the wood products industry, how pellet production affects ecosystem services and biodiversity, and what methods are in place to monitor changes and protect vulnerable systems. Scientific studies provide evidence that wood pellets in the SE USA are a fraction of total forestry operations and can be produced while maintaining or improving forest ecosystem services. Ecosystem services are protected by the requirement to utilize loggers trained to apply scientifically based best management practices in planning and implementing harvest for the export market. Bioenergy markets supplement incomes to private rural landholders and provide an incentive for forest management practices that simultaneously benefit water quality and wildlife and reduce risk of fire and insect outbreaks. Bioenergy also increases the value of forest land to landowners, thereby decreasing likelihood of conversion to nonforest uses. Monitoring and evaluation are essential to verify that regulations and good practices are achieving goals and to enable timely responses if problems arise. Conducting rigorous research to understand how conditions change in response to management choices requires baseline data, monitoring, and appropriate reference scenarios. Furthermore, long-term monitoring data on forest conditions should be publicly accessible and utilized to inform adaptive management.« less

Status and prospects for renewable energy using wood pellets from the southeastern United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dale, Virginia H.; Kline, Keith L.; Parish, Esther S.

The ongoing debate about costs and benefits of wood-pellet based bioenergy production in the southeastern United States (SE USA) requires an understanding of the science and context influencing market decisions associated with its sustainability. Production of pellets has garnered much attention as US exports have grown from negligible amounts in the early 2000s to 4.6 million metric tonnes in 2015. Currently, 98% of these pellet exports are shipped to Europe to displace coal in power plants. We ask, 'How is the production of wood pellets in the SE USA affecting forest systems and the ecosystem services they provide?' To addressmore » this question, we review current forest conditions and the status of the wood products industry, how pellet production affects ecosystem services and biodiversity, and what methods are in place to monitor changes and protect vulnerable systems. Scientific studies provide evidence that wood pellets in the SE USA are a fraction of total forestry operations and can be produced while maintaining or improving forest ecosystem services. Ecosystem services are protected by the requirement to utilize loggers trained to apply scientifically based best management practices in planning and implementing harvest for the export market. Bioenergy markets supplement incomes to private rural landholders and provide an incentive for forest management practices that simultaneously benefit water quality and wildlife and reduce risk of fire and insect outbreaks. Bioenergy also increases the value of forest land to landowners, thereby decreasing likelihood of conversion to nonforest uses. Monitoring and evaluation are essential to verify that regulations and good practices are achieving goals and to enable timely responses if problems arise. Conducting rigorous research to understand how conditions change in response to management choices requires baseline data, monitoring, and appropriate reference scenarios. Furthermore, long-term monitoring data on forest conditions should be publicly accessible and utilized to inform adaptive management.« less

Emotional intelligence moderates the relationship between regional gray matter volume in the bilateral temporal pole and critical thinking disposition.

PubMed

Yao, Xiaonan; Yuan, Shuge; Yang, Wenjing; Chen, Qunlin; Wei, Dongtao; Hou, Yuling; Zhang, Lijie; Qiu, Jiang; Yang, Dong

2018-04-01

Critical thinking enables people to form sound beliefs and provides a basis for emotional life. Research has indicated that individuals with better critical thinking disposition can better recognize and regulate their emotions, though the neuroanatomical mechanisms involved in this process remain to be elucidated. Further, the influence of emotional intelligence on the relationship between brain structure and critical thinking disposition has not been examined. The present study utilized voxel-based morphometry (VBM) to investigate the neural structures underlying critical thinking disposition in a large sample of college students (N = 296). Regional gray matter volume (rGMV) in the bilateral temporal pole, which reflects an individual's ability to process social and emotional information, was negatively correlated with critical thinking disposition. In addition, rGMV in bilateral para hippocampal regions -regions involved in contextual association/emotional regulation-exhibited negative correlation with critical thinking disposition. Further analysis revealed that emotional intelligence moderated the relationship between rGMV of the temporal pole and critical thinking disposition. Specifically, critical thinking disposition was associated with decreased GMV of the temporal pole for individuals who have relatively higher emotional intelligence rather than lower emotional intelligence. The results of the present study indicate that people who have higher emotional intelligence exhibit more effective and automatic processing of emotional information and tend to be strong critical thinkers.

Force characteristics of a modular squeeze mode magneto-rheological element

NASA Astrophysics Data System (ADS)

Craft, Michael J.; Ahmadian, Mehdi; Farjoud, Alireza; Burke, William C. T.; Nagode, Clement

2010-04-01

While few publications exist on the behavior of Magneto-Rheological (MR) fluid in squeeze mode, devices using squeeze mode may take advantage of the very large range of adjustment that squeeze mode offers. Based on results obtained through modeling and testing MR fluid in a squeeze mode rheometer, a novel compression-adjustable element has been fabricated and tested, which utilizes MR fluid in squeeze mode. While shear and valve modes have been used exclusively for MR fluid damping applications, recent modeling and testing with MR fluid has revealed that much larger adjustment ranges are achievable in squeeze mode. Utilizing squeeze mode, a compression element, or MR Pouch, was developed consisting of a flexible cylindrical membrane with each end fastened to a steel endplate (pole plates). The silicone rubber pouch material was molded in the required shape for use in the squeeze mode rheometer. This flexible membrane allows for the complete self-containment of MR fluid and because the pouch compensates for volume changes, there is no need for dynamic seals and associated surface finish treatments on the steel components. An electromagnet incorporated in the rheometer passes an adjustable magnetic field axially through the pole plates and MR fluid. Test results show the device was capable of varying the compression force from less than 8lbs to greater than 1000lbs when the pole plates were 0.050" apart. Simulations were compared against test data with good correlation. Possible applications of this technology include primary suspension components, auxiliary suspension bump stops, and other vibration isolation components, as MR Pouches are scalable depending on the application and force requirements.

Modeling the CO2-effects of forest management and wood usage on a regional basis.

PubMed

Knauf, Marcus; Köhl, Michael; Mues, Volker; Olschofsky, Konstantin; Frühwald, Arno

2015-12-01

At the 15 th Conference of Parties of the UN Framework Convention on Climate Change, Copenhagen, 2009, harvested wood products were identified as an additional carbon pool. This modification eliminates inconsistencies in greenhouse gas reporting by recognizing the role of the forest and timber sector in the global carbon cycle. Any additional CO 2 -effects related to wood usage are not considered by this modification. This results in a downward bias when the contribution of the forest and timber sector to climate change mitigation is assessed. The following article analyses the overall contribution to climate protection made by the forest management and wood utilization through CO 2 -emissions reduction using an example from the German state of North Rhine-Westphalia. Based on long term study periods (2011 to 2050 and 2100, respectively). Various alternative scenarios for forest management and wood usage are presented. In the mid- to long-term (2050 and 2100, respectively) the net climate protection function of scenarios with varying levels of wood usage is higher than in scenarios without any wood usage. This is not observed for all scenarios on short and mid term evaluations. The advantages of wood usage are evident although the simulations resulted in high values for forest storage in the C pools. Even the carbon sink effect due to temporal accumulation of deadwood during the period from 2011 to 2100 is outbalanced by the potential of wood usage effects. A full assessment of the CO 2 -effects of the forest management requires an assessment of the forest supplemented with an assessment of the effects of wood usage. CO 2 -emission reductions through both fuel and material substitution as well as CO 2 sink in wood products need to be considered. An integrated assessment of the climate protection function based on the analysis of the study's scenarios provides decision parameters for a strategic approach to climate protection with regard to forest management and wood use at regional and national levels. The short-term evaluation of subsystems can be misleading, rendering long-term evaluations (until 2100, or even longer) more effective. This is also consistent with the inherently long-term perspective of forest management decisions and measures.

Contrasting diets reveal metabolic plasticity in the tree-killing beetle, Anoplophora glabripennis (Cerambycidae: Lamiinae)

NASA Astrophysics Data System (ADS)

Mason, Charles J.; Scully, Erin D.; Geib, Scott M.; Hoover, Kelli

2016-09-01

Wood-feeding insects encounter challenging diets containing low protein quantities, recalcitrant carbohydrate sources, and plant defensive compounds. The Asian longhorned beetle (Anoplophora glabripennis) is a wood-feeding insect that attacks and kills a diversity of hardwood tree species. We compared gene expression of midguts collected from larvae feeding in a preferred tree, sugar maple, to those consuming a nutrient-rich artificial diet, to identify genes putatively involved in host plant utilization. Anoplophora glabripennis larvae exhibited differential expression of ~3600 genes in response to different diets. Genes with predicted capacity for plant and microbial carbohydrate usage, detoxification, nutrient recycling, and immune-related genes relevant for facilitating interactions with microbial symbionts were upregulated in wood-feeding larvae compared to larvae feeding in artificial diet. Upregulation of genes involved in protein degradation and synthesis was also observed, suggesting that proteins incur more rapid turnover in insects consuming wood. Additionally, wood-feeding individuals exhibited elevated expression of several mitochondrial cytochrome C oxidase genes, suggesting increased aerobic respiration compared to diet-fed larvae. These results indicate that A. glabripennis modulates digestive and basal gene expression when larvae are feeding in a nutrient-poor, yet suitable host plant compared to a tractable and nutrient-rich diet that is free of plant defensive compounds.

Ion Beam Analyses Of Bark And Wood In Environmental Studies

NASA Astrophysics Data System (ADS)

Lill, J.-O.; Saarela, K.-E.; Harju, L.; Rajander, J.; Lindroos, A.; Heselius, S.-J.

2011-06-01

A large number of wood and bark samples have been analysed utilizing particle-induced X-ray emission (PIXE) and particle-induced gamma-ray emission (PIGE) techniques. Samples of common tree species like Scots Pine, Norway Spruce and birch were collected from a large number of sites in Southern and Southwestern Finland. Some of the samples were from a heavily polluted area in the vicinity of a copper-nickel smelter. The samples were dry ashed at 550 °C for the removal of the organic matrix in order to increase the analytical sensitivity of the method. The sensitivity was enhanced by a factor of 50 for wood and slightly less for bark. The ashed samples were pressed into pellets and irradiated as thick targets with a millimetre-sized proton beam. By including the ashing procedure in the method, the statistical dispersion due to elemental heterogeneities in wood material could be reduced. As a by-product, information about the elemental composition of ashes was obtained. By comparing the concentration of an element in bark ash to the concentration in wood ash of the same tree useful information from environmental point of view was obtained. The obtained ratio of the ashes was used to distinguish between elemental contributions from anthropogenic atmospheric sources and natural geochemical sources, like soil and bedrock.

The Feasibility of Sugar Palm (Arenga pinnata) Trunk for Raw Material of Parquet (Wood Flooring)

NASA Astrophysics Data System (ADS)

Nuryawan, A.; Tarigan, A.; Hakim, L.

2017-03-01

In the market, parquet was made from high density wood such as teak, merbau, kempas, ulin, oak, lime, maple, or other high density wood. Parquet has been used for flooring in specific buildings, for instance sport hall, library, commercial building (i.e hotel lobby, hypermarket), and office building. Because of the scarcity of high density wood nowadays and in order to find out the alternative material for wood flooring, the utilization of sugar palm trunk was considered. In this contribution, unproductive sugar palm tree was cut down and divided into three sections using chain saw, namely bottom, middle, and tip. For each section, physical and mechanical samples testing were made according to British Standard 373:1957 for small clear specimen. Investigation of both properties was done in ambient temperature with at least three replications. Instron UTM (Universal Testing Machine) was used to evaluate the mechanical properties. Results of the physical testing (density, moisture content and tangential shrinkage) showed the entire trunk was suitable for raw material of parquet. However, the results of mechanical testing (hardness, MOE/modulus of elasticity, MOR/modulus of rupture, and compression perpendicular to grain) showed only bottom and middle parts were suitable for raw material of parquet while the upper part was vice versa.

Performance-oriented packaging testing of PPP-B-601 ERAPS wood box for packing Group II solid hazardous material. Test report for Oct 91

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, E.

1991-10-01

Qualification tests were performed to determine whether the in-service PPP-B-601 ERAPS Wood Box could be utilized to contain properly dunnaged solid type hazardous materials weighing up to a gross weight of 237 kg (523 pounds). The tests were conducted in accordance with Performance Oriented Packaging (POP) requirements specified by the United Nations Recommendations on the Transportation of Dangerous Goods. The box has conformed to the POP performance requirements; i.e., the box successfully retained its contents throughout the stacking, vibration and drop tests.

Analysis of Competitiveness and Support Instruments for Heat and Electricity Production from Wood Biomass in Latvia

NASA Astrophysics Data System (ADS)

Klavs, G.; Kudrenickis, I.; Kundzina, A.

2012-01-01

Utilisation of renewable energy sources is one of the key factors in a search for efficient ways of reducing the emissions of greenhouse gases and improving the energy supply security. So far, the district heating supply in Latvia has been based on natural gas, with the wood fuel playing a minor role; the same is true for decentralised combined heat-power (CHP) production. The paper describes a method for evaluation of the economic feasibility of heat and electricity production from wood biomass under the competition between different fuel types and taking into account the electricity market. For the simulation, a cost estimation model is applied. The results demonstrate that wood biomass can successfully be utilised for competitive heat production by boiler houses, while for electricity production by CHP utilities it cannot compete on the market (even despite the low prices on wood biomass fuel) unless particular financial support instruments are applied. The authors evaluate the necessary support level and the impact of two main support instruments - the investment subsidies and the feed-in tariff - on the economic viability of wood-fuelled CHP plants, and show that the feed-in tariff could be considered as an instrument strongly affecting the competitiveness of such type CHP. Regarding the feed-in tariff determination, a compromise should be found between the economy-dictated requirement to develop CHP projects concerning capacities above 5 MWel - on the one hand, and the relatively small heat loads in many Latvian towns - on the other.

Modeling opportunities and feasibility of siting wood-fired electrical generating facilities to facilitate landscape-scale fuel treatment with FIA BioSum.

Treesearch

Jeremy S. Fried; Glenn Christensen; Dale Weyermann; R. Jamie Barbour; Roger Fight; Bruce Hiserote; Guy Pinjuv

2005-01-01

Utilization of small diameter trees is viewed by many as the key to making landscape-scale fuel treatment financially feasible. But little capacity currently exists for utilizing such material and capacity of sufficient scale to have a significant impact on the economics of small diameter removals will only be added if predictable feedstocks can be assured. The FIA...

47 CFR 1.1417 - Allocation of Unusable Space Costs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Allocation of Unusable Space Costs. 1.1417... Attachment Complaint Procedures § 1.1417 Allocation of Unusable Space Costs. (a) With respect to the formula referenced in § 1.1409(e)(2), a utility shall apportion the cost of providing unusable space on a pole so...

47 CFR 1.1417 - Allocation of Unusable Space Costs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Allocation of Unusable Space Costs. 1.1417... Attachment Complaint Procedures § 1.1417 Allocation of Unusable Space Costs. (a) With respect to the formula referenced in § 1.1409(e)(2), a utility shall apportion the cost of providing unusable space on a pole so...

A bobcat does a high-wire act at KSC

NASA Technical Reports Server (NTRS)

1998-01-01

A young, male bobcat balances gingerly on telephone pole cables next to the south-bound lane of Kennedy Parkway. The cat is nocturnal and is seldom observed during the day unless scared from its daytime shelter in the grass or beneath a shrub. Usually found in broken sections of heavily wooded or brushy country, bobcats are reported as common in scrub strand and roadside or weedy grass habitats at KSC. The bobcat is known to inhabit mangrove habitats and will readily swim across small bodies of water. The bobcat occurs across southern Canada then south over the entire United States, except for the midwestern corn belt, to southern Mexico. It is the last large mammalian predator remaining on KSC. Kennedy Space Center is located in the Merritt Island National Wildlife Refuge, which is home to many species of wild animals, including the bobcat.

KSC-98pc1602

NASA Image and Video Library

1998-11-10

KENNEDY SPACE CENTER, FLA. -- A young, male bobcat balances gingerly on telephone pole cables next to the south-bound lane of Kennedy Parkway. The cat is nocturnal and is seldom observed during the day unless scared from its daytime shelter in the grass or beneath a shrub. Usually found in broken sections of heavily wooded or brushy country, bobcats are reported as common in scrub strand and roadside or weedy grass habitats at KSC. The bobcat is known to inhabit mangrove habitats and will readily swim across small bodies of water. The bobcat occurs across southern Canada then south over the entire United States, except for the midwestern corn belt, to southern Mexico. It is the last large mammalian predator remaining on KSC. The Merritt Island National Wildlife Refuge, which is located on Kennedy Space Center property, is home to many species of wild animals, including the bobcat.

KSC-2011-5977

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are Jim Green, director of the Planetary Science Division at Headquarters in Washington, D.C.; Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods

Passive Infrared Thermographic Imaging for Mobile Robot Object Identification

NASA Astrophysics Data System (ADS)

Hinders, M. K.; Fehlman, W. L.

2010-02-01

The usefulness of thermal infrared imaging as a mobile robot sensing modality is explored, and a set of thermal-physical features used to characterize passive thermal objects in outdoor environments is described. Objects that extend laterally beyond the thermal camera's field of view, such as brick walls, hedges, picket fences, and wood walls as well as compact objects that are laterally within the thermal camera's field of view, such as metal poles and tree trunks, are considered. Classification of passive thermal objects is a subtle process since they are not a source for their own emission of thermal energy. A detailed analysis is included of the acquisition and preprocessing of thermal images, as well as the generation and selection of thermal-physical features from these objects within thermal images. Classification performance using these features is discussed, as a precursor to the design of a physics-based model to automatically classify these objects.

Determining heterogeneous slip activity on multiple slip systems from single crystal orientation pole figures

DOE PAGES

Pagan, Darren C.; Miller, Matthew P.

2016-09-01

A new experimental method to determine heterogeneity of shear strains associated with crystallographic slip in the bulk of ductile, crystalline materials is outlined. The method quantifies the time resolved evolution of misorientation within plastically deforming crystals using single crystal orientation pole figures (SCPFs) measured in-situ with X-ray diffraction. A multiplicative decomposition of the crystal kinematics is used to interpret the distributions of lattice plane orientation observed on the SCPFs in terms of heterogeneous slip activity (shear strains) on multiple slip systems. Here, to show the method’s utility, the evolution of heterogeneous slip is quantified in a silicon single crystal plasticallymore » deformed at high temperature at multiple load steps, with slip activity in sub-volumes of the crystal analyzed simultaneously.« less

Single-Pole Double-Throw MMIC Switches for a Microwave Radiometer

NASA Technical Reports Server (NTRS)

Montes, Oliver; Dawson, Douglas E.; Kangaslahti, Pekka P.

2012-01-01

In order to reduce the effect of gain and noise instabilities in the RF chain of a microwave radiometer, a Dicke radiometer topology is often used, as in the case of the proposed surface water and ocean topography (SWOT) radiometer instrument. For this topology, a single-pole double-throw (SPDT) microwave switch is needed, which must have low insertion loss at the radiometer channel frequencies to minimize the overall receiver noise figure. Total power radiometers are limited in accuracy due to the continuous variation in gain of the receiver. High-frequency SPDT switches were developed in the form of monolithic microwave integrated circuits (MMICs) using 75 micron indium phosphide (InP) PIN-diode technology. These switches can be easily integrated into Dicke switched radiometers that utilize microstrip technology.

Robust and Low-Cost Flame-Treated Wood for High-Performance Solar Steam Generation.

PubMed

Xue, Guobin; Liu, Kang; Chen, Qian; Yang, Peihua; Li, Jia; Ding, Tianpeng; Duan, Jiangjiang; Qi, Bei; Zhou, Jun

2017-05-03

Solar-enabled steam generation has attracted increasing interest in recent years because of its potential applications in power generation, desalination, and wastewater treatment, among others. Recent studies have reported many strategies for promoting the efficiency of steam generation by employing absorbers based on carbon materials or plasmonic metal nanoparticles with well-defined pores. In this work, we report that natural wood can be utilized as an ideal solar absorber after a simple flame treatment. With ultrahigh solar absorbance (∼99%), low thermal conductivity (0.33 W m -1 K -1 ), and good hydrophilicity, the flame-treated wood can localize the solar heating at the evaporation surface and enable a solar-thermal efficiency of ∼72% under a solar intensity of 1 kW m -2 , and it thus represents a renewable, scalable, low-cost, and robust material for solar steam applications.

CosmoBon, tree research team, for studying utilization of woody plant in space environment

NASA Astrophysics Data System (ADS)

Tomita-Yokotani, Kaori; Yamashita, Masamichi; Hashimoto, Hirofumi; Sato, Seigo; Baba, Keiichi; Chida, Yukari

2012-07-01

We are proposing to raise woody plants in space for several applications and plant science, as Tree research team, TRT. Trees produce excess oxygen, wooden materials for living cabin, and provide biomass for cultivating mushroom and insect as for the space agriculture. Excellent tree shapes which would be deeply related to wood formation improve quality of life under stressful environment in outer space. We have the serious problem about their size. Bonsai is one of the Japanese traditional arts. We have been investigating the tension wood formation under exotic gravitational environment using Bonsai. CosmoBon is the small tree Bonsai for our space experiment. The tension wood formation in CosmoBon was confirmed as the same as that in the natural trees. Our goal is to examine feasibility to grow various species of trees in space as bioresource for space agriculture.

Estimation of wood density and chemical composition by means of diffuse reflectance mid-infrared Fourier transform (DRIFT-MIR) spectroscopy.

PubMed

Nuopponen, Mari H; Birch, Gillian M; Sykes, Rob J; Lee, Steve J; Stewart, Derek

2006-01-11

Sitka spruce (Picea sitchensis) samples (491) from 50 different clones as well as 24 different tropical hardwoods and 20 Scots pine (Pinus sylvestris) samples were used to construct diffuse reflectance mid-infrared Fourier transform (DRIFT-MIR) based partial least squares (PLS) calibrations on lignin, cellulose, and wood resin contents and densities. Calibrations for density, lignin, and cellulose were established for all wood species combined into one data set as well as for the separate Sitka spruce data set. Relationships between wood resin and MIR data were constructed for the Sitka spruce data set as well as the combined Scots pine and Sitka spruce data sets. Calibrations containing only five wavenumbers instead of spectral ranges 4000-2800 and 1800-700 cm(-1) were also established. In addition, chemical factors contributing to wood density were studied. Chemical composition and density assessed from DRIFT-MIR calibrations had R2 and Q2 values in the ranges of 0.6-0.9 and 0.6-0.8, respectively. The PLS models gave residual mean squares error of prediction (RMSEP) values of 1.6-1.9, 2.8-3.7, and 0.4 for lignin, cellulose, and wood resin contents, respectively. Density test sets had RMSEP values ranging from 50 to 56. Reduced amount of wavenumbers can be utilized to predict the chemical composition and density of a wood, which should allow measurements of these properties using a hand-held device. MIR spectral data indicated that low-density samples had somewhat higher lignin contents than high-density samples. Correspondingly, high-density samples contained slightly more polysaccharides than low-density samples. This observation was consistent with the wet chemical data.

Lung function measures following simulated wildland firefighter exposures.

PubMed

Ferguson, Matthew D; Semmens, Erin O; Weiler, Emily; Domitrovich, Joe; French, Mary; Migliaccio, Christopher; Palmer, Charles; Dumke, Charles; Ward, Tony

2017-09-01

Across the world, biomass smoke is a major source of air pollution and is linked with a variety of adverse health effects. This is particularly true in the western U.S. where wood smoke from wildland forest fires are a significant source of PM 2.5 . Wildland firefighters are impacted as they experience elevated PM 2.5 concentrations over extended periods of time, often occurring during physical exertion. Various epidemiological studies have investigated wood smoke impacts on human health, including occupational field exposures experienced by wildland firefighters. As there are numerous challenges in carrying out these field studies, having the ability to research the potential health impacts to this occupational cohort in a controlled setting would provide important information that could be translated to the field setting. To this end, we have carried out a simulated wildland firefighter exposure study in a wood smoke inhalation facility. Utilizing a randomized crossover trial design, we exposed 10 participants once to clean filtered-air, 250 µg/m 3 , and 500 µg/m 3 wood stove-generated wood smoke PM 2.5 . Participants exercised on a treadmill at an absolute intensity designed to simulate wildland firefighting for 1.5 hr. In addition to measured PM 2.5 smoke concentrations, mean levels of CO 2 , CO, and % relative humidity were continuously monitored and recorded and were representative of occupational "real-world" exposures. Pulmonary function was measured at three time points: before, immediately after, and 1-hr post-exposure. Although there were some reductions in FVC, FEV 1 , and FVC:FEV 1 measures, results of the spirometry testing did not show significant changes in lung function. The development of this wood smoke inhalational facility provides a platform to further address unique research questions related to wood smoke exposures and associated adverse health effects.

Recycling of plastic: accounting of greenhouse gases and global warming contributions.

PubMed

Astrup, Thomas; Fruergaard, Thilde; Christensen, Thomas H

2009-11-01

Major greenhouse gas (GHG) emissions related to plastic waste recycling were evaluated with respect to three management alternatives: recycling of clean, single-type plastic, recycling of mixed/contaminated plastic, and use of plastic waste as fuel in industrial processes. Source-separated plastic waste was received at a material recovery facility (MRF) and processed for granulation and subsequent downstream use. In the three alternatives, plastic was assumed to be substituting virgin plastic in new products, wood in low-strength products (outdoor furniture, fences, etc.), and coal or fuel oil in the case of energy utilization. GHG accounting was organized in terms of indirect upstream emissions (e.g. provision of energy, fuels, and materials), direct emissions at the MRF (e.g. fuel combustion), and indirect downstream emissions (e.g. avoided emissions from production of virgin plastic, wood, or coal/oil). Combined, upstream and direct emissions were estimated to be roughly between 5 and 600 kg CO(2)-eq. tonne( -1) of plastic waste depending on treatment at the MRF and CO(2) emissions from electricity production. Potential downstream savings arising from substitution of virgin plastic, wood, and energy fuels were estimated to be around 60- 1600 kg CO(2)-eq. tonne( -1) of plastic waste depending on substitution ratios and CO(2) emissions from electricity production. Based on the reviewed data, it was concluded that substitution of virgin plastic should be preferred. If this is not viable due to a mixture of different plastic types and/or contamination, the plastic should be used for energy utilization. Recycling of plastic waste for substitution of other materials such as wood provided no savings with respect to global warming.

Development of a Multiple Input Integrated Pole-to-Pole Global CMORPH

NASA Astrophysics Data System (ADS)

Joyce, R.; Xie, P.

2013-12-01

A test system is being developed at NOAA Climate Prediction Center (CPC) to produce a passive microwave (PMW), IR-based, and model integrated high-resolution precipitation estimation on a 0.05olat/lon grid covering the entire globe from pole to pole. Experiments have been conducted for a summer Test Bed period using data for July and August of 2009. The pole-to-pole global CMORPH system is built upon the Kalman Filter based CMORPH algorithm of Joyce and Xie (2011). First, retrievals of instantaneous precipitation rates from PMW observations aboard nine low earth orbit (LEO) satellites are decoded and pole-to-pole mapped onto a 0.05olat/lon grid over the globe. Also precipitation estimates from LEO AVHRR retrievals are derived using a PDF matching of LEO IR with calibrated microwave combined (MWCOMB) precipitation retrievals. The motion vectors for the precipitating cloud systems are defined using information from both satellite IR observations and precipitation fields generated by the NCEP Climate Forecast System Reanalysis (CFSR). To this end, motion vectors are first computed for the CFSR hourly precipitation fields through cross-correlation analysis of consecutive hourly precipitation fields on the global T382 (~35 km) grid. In a similar manner, separate processing is also performed on satellite IR-based precipitation estimates to derive motion vectors from observations. A blended analysis of precipitating cloud motion vectors is then constructed through the combination of CFSR and satellite-derived vectors utilizing a two-dimensional optimal interpolation (2D-OI) method, in which CFSR-derived motion vectors are used as the first guess and subsequently satellite derived vectors modify the first guess. Weights used to generate the combinations are defined under the OI framework as a function of error statistics for the CFSR and satellite IR based motion vectors. The screened and calibrated PMW and AVHRR derived precipitation estimates are then separately spatially propagated forward and backward in time, using precipitating cloud motion vectors, from their observation time to the next PMW observation. The PMW estimates propagated in both the forward and backward directions are then combined with propagated IR-based precipitation estimates under the Kalman Filter framework, with weights defined based on previously determined error statistics dependent on latitude, season, surface type, and temporal distance from observation time. Performance of the pole-to-pole global CMORPH and its key components, including combined PMW (MWCOMB), IR-based, and model precipitation, as well as model-derived, IR-based, and blended precipitation motion vectors, will be examined against NSSL Q2 radar observed precipitation estimates over CONUS, Finland FMI radar precipitation, and a daily gauge-based analysis including daily Canadian surface reports over global land. Also an initial investigation will be performed over a January - February 2010 winter Test Bed period. Detailed results will be reported at the Fall 2013 AGU Meeting.

Adapting an IPCC-Compliant Full Forest Carbon Accounting Model to Determine the Effects of Different Forest Management Strategies in California

NASA Astrophysics Data System (ADS)

Starrs, C.; Stewart, W.; Potts, M. D.

2016-12-01

As California experiences increasing rates of disturbance events such as wildfire, drought, and insect outbreaks, understanding how different management strategies affect long-term forest carbon stock changes in the forest and in harvested wood products used by society will be key to determining strategies to best maximize forest-related carbon sequestration in the future. California's forest area is roughly evenly split across three ownership types: private timberlands, National Forest timberlands, and reserved forests. Forest management strategies in California generally vary by these ownerships; management in reserved lands sequesters carbon within the forest (i.e. leaves wood in the forest), while on private and National Forest timberlands a significant amount of wood is removed from the forest and converted to harvested wood products. The Carbon Budget Model of the Canadian Forest Sector (CBM-CFS3) is an IPCC-compliant full forest carbon accounting model developed for use in Canada that has been adapted for use in other countries. Changes in natural disturbances in the forest and technological innovation in the use of harvested wood products could substantially alter future carbon trajectories of forests under different management regimes. A key advantage of the CBM-CFS3 model is that in addition to tracking live tree, dead tree, and dead organic matter (DOM) carbon pools in the forest, it also tracks carbon stock changes in harvested wood products. We calibrated the CBM-CFS3 model with US Forest Service Forest Inventory and Analysis (FIA) data for seven forest types across three ownership types to predict carbon stock changes under different natural disturbance and harvested wood product utilization futures. Our results illustrate the importance of using a tractable model that can integrate future changes in forest carbon cycling to keep pace with our changing climate and usage of wood products.

Testing the utility of the 3-PG model for growth of Eucalyptus grandis x urophylla with natural and manipulated supplies of water and nutrients

Treesearch

Jose Luiz Stape; Michael G. Ryan; Dan Binkley

2004-01-01

The productivity of fast-growing tropical plantations depends, in part, on the ability of trees to obtain and utilize site resources, and the allocation of fixed carbon (C) to wood production. Simulation models can represent these processes and interactions, but the value of these models depends on their ability to improve predictions of stand growth relative to...

Design, synthesis, and activity of nanocellulosic protease sensors

USDA-ARS?s Scientific Manuscript database

Here we contrast the molecular assembly, and biochemical utility of nanocellulosic materials prepared from cotton and wood as protease sensors. The cotton-based nanocellulosic substrates were prepared in a variety of ways to produce nanocrystals, films and aerogels, which were derivatized with eithe...

Wood utilization

Treesearch

Eugene M. Wengert; Dennis M. Donnelly; Donald C. Markstrom; Harold E. Worth

1985-01-01

In the past, markets for quaking aspen timber from the Rocky Mountains have been insufficient to support significant harvesting. This shortage of markets severely restrained the potential for aspen management. As a result, many stands protected from wildfire gradually reverted to conifers (see the VEGETATIVE REGENERATION and FIRE chapters).

Ionic liquid-facilitated preparation of lignocellulosic composites

USDA-ARS?s Scientific Manuscript database

Lignocellulosic composites (LCs) were prepared by partially dissolving cotton along with steam exploded Aspen wood and burlap fabric reinforcements utilizing an ionic liquid (IL) solvent. Two methods of preparation were employed. In the first method, a controlled amount of IL was added to preassembl...

Southern pulpwood production, 1982

Treesearch

James F. Rosson

1982-01-01

The annual report of southern pulpwood production is based on a canvass of all pulpmills that fall within the 12 states of the Southern and Southeastern Forest Experiment Station regions. Neighboring experiment stations exchange information on mills located beyond the region but utilizing wood from the region.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Raptor community composition in the Texas Southern High Plains lesser prairie-chicken range

USGS Publications Warehouse

Behney, A.C.; Boal, Clint W.; Whitlaw, Heather A.; Lucia, D.R.

2012-01-01

Predation can be a factor in preventing prey population growth and sustainability when prey populations are small and fragmented, and when predator density is unrelated to the density of the single prey species. We conducted monthly raptor surveys from February 2007 to May 2009 in adjacent areas of the Texas Southern High Plains (USA) that do and do not support lesser prairie-chickens (Tympanuchus pallidicinctus), a candidate for protection under the Endangered Species Act. During the summer period corresponding to prairie-chicken nesting and brood-rearing, Swainson's hawks (Buteo swainsoni) were the most abundant raptor. During the lekking and overwintering period, the raptor community was diverse, with northern harriers (Circus cyaneus) being the most abundant species. Raptor abundance peaked during the early autumn and was lowest during the spring. Utility poles were a significant predictor of raptor density at survey points and Swainson's hawks and all raptors, pooled, were found in greater densities in non-prairie-chicken habitat dominated by mesquite (Prosopis glandulosa). Avian predation risk on prairie-chickens, based on presence and abundance of raptors, appears to be greatest during winter when there is a more abundant and diverse raptor community, and in areas with utility poles.

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy-Efficient Wood-Plastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

David N. Thompson, Robert W. Emerick, Alfred B. England, James P. Flanders, Frank J. Loge, Katherine A. Wiedeman, Michael P. Wolcott

The forestry, wood and paper industries in the United States provide thousands of productive well-paying jobs; however, in the face of the recent economic downturn it faces significant challenges in remaining economically viable and competitive. To compete successfully on a global market that is increasingly driven by the need for sustainable products and practices, the industry must improve margins and diversify product lines while continuing to produce the staple products. One approach that can help to accomplish this goal sustainably is the forest biorefinery. In the forest biorefinery, traditional waste streams are utilized singly or in combination to manufacture additionalmore » products in a profitable and environmentally sustainable manner. In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. Renewable microbial polyesters are not currently used in WFRTCs primarily because their production costs are several times higher than those of conventional petrochemical-derived plastics, limiting their use to small specialty markets. The strategy for this project was to economically produce WFRTCs using microbial polyesters by reducing or eliminating the most costly steps in the bio-plastic production. This would be achieved by producing them in and from waste effluents from the municipal and forest products sectors, and by eliminating the costly purification steps. After production the plasticladen biosolids would be dried and used directly to replace petroleum-derived plastics in WFRTCs. Using this strategy, we could greatly reduce the cost of producing and utilizing these renewable plastics in WFRTCs. This was a collaborative project among the Idaho National Laboratory, Washington State University, the University of California-Davis, Glatfelter Corporation, Strandex Corporation, and ECO:LOGIC Engineering, Inc. The project was comprised of five tasks. The first four tasks addressed PHA production, extrusion, and composite properties. Feedstock performance and compositional properties were determined in the laboratory by WSU. Both pure commercial PHAs (Task 1) and unpurified effluentderived PHAs (Task 4) were used. Results were used to define appropriate effluent feedstocks (Task 2) and optimize supplements (Task 3) to produce biosolids for the preferred composite formulations. Task 5 included a pilot-scale extrusion of wood-PHA-biosolids composites.« less

Enhanced piezoelectricity and high temperature poling effect in (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 ceramics via an ethylene glycol route

NASA Astrophysics Data System (ADS)

Tailor, H. N.; Ye, Z.-G.

2010-05-01

A solution chemical method utilizing ethylene glycol as solvent has been developed to prepare the ceramics of (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3[(1-x)PMN-xPT] from a precursor powder that can be pressed and fired in one step to produce high quality ceramics with excellent piezoelectric properties. The ceramics reach a relative density of up to 97% of the theoretical value after direct calcinations. This high density is achieved without the need of additional sintering after calcination which is usually required in conventional solid state syntheses to produce ceramics. The ceramics exhibit a unipolar piezoelectric coefficient d33 of 848 pC/N, which is one of the highest values for any unmodified/untextured binary systems reported to date. Since the piezoelectric properties depend on composition and electric field, the effect of poling conditions was investigated. A critical temperature limit has been found, above which poling can dramatically impair the piezoelectric properties due to a field-induced increase in the monoclinic phase component around the morphotropic phase boundary.

Refined Rotational Period, Pole Solution, and Shape Model for (3200) Phaethon

NASA Astrophysics Data System (ADS)

Ansdell, Megan; Meech, Karen J.; Hainaut, Olivier; Buie, Marc W.; Kaluna, Heather; Bauer, James; Dundon, Luke

2014-09-01

(3200) Phaethon exhibits both comet- and asteroid-like properties, suggesting it could be a rare transitional object such as a dormant comet or previously volatile-rich asteroid. This justifies detailed study of (3200) Phaethon's physical properties as a better understanding of asteroid-comet transition objects can provide insight into minor body evolution. We therefore acquired time series photometry of (3200) Phaethon over 15 nights from 1994 to 2013, primarily using the Tektronix 2048 × 2048 pixel CCD on the University of Hawaii 2.2 m telescope. We utilized light curve inversion to (1) refine (3200) Phaethon's rotational period to P = 3.6032 ± 0.0008 hr; (2) estimate a rotational pole orientation of λ = +85° ± 13° and β = -20° ± 10° and (3) derive a shape model. We also used our extensive light curve data set to estimate the slope parameter of (3200) Phaethon's phase curve as G ~ 0.06, consistent with C-type asteroids. We discuss how this highly oblique pole orientation with a negative ecliptic latitude supports previous evidence for (3200) Phaethon's origin in the inner main asteroid belt as well as the potential for deeply buried volatiles fueling impulsive yet rare cometary outbursts.

Dow and Mary Davidson residence - A residence in a hot humid climate with major living spaces in rooms without walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holder, L.M. III; Holder, L.M. IV

Dow Davidson works out of his home while his wife, Mary, home schools their three children. The entire family uses the house full time throughout the year. Dow and Mary Davidson stressed the importance of a home with minimal site disruption while providing for as many human needs as practical. Specific requirements were for harmony with the natural climate and adjacent bird sanctuary. The clients had a strong preference for a pole structural system reflecting buildings they were familiar with in Hawaii. The house was designed as a pole structure utilizing passive solar heating, natural ventilation, night flushing, daylighting, rainwatermore » harvesting, and an outdoor and indoor living area without walled separation from the climate. This type of open indoor/outdoor living is an extension of the Hawaiian experience. Use of the pole structure system provided compatibility between the residence and the neighboring bird habitat. The completed house easily blended with the surrounding vegetation due to the extensive use of natural materials. Exterior walks and drives, made from caliche and mulch (harvested from cedar cut on-site), helped further balance the structure with the terrain and vegetation.« less

Socio-economic factors affecting the conservation of natural woodlands in Central Riyadh Area – Saudi Arabia

PubMed Central

Al-Subaiee, Faisal Sultan

2015-01-01

This study aimed to identify some socioeconomic factors affecting local people in central Riyadh area for the utilization of wood and other energy sources in cooking and heating in order to develop some recommendations for conserving woodlands. The study results revealed that gas is the most common energy source used for cooking with a mean usage level of 2.79 (SD = 0.58). On the other hand, wood ranked first for heating with the highest mean, usage level of 1.90 (SD = 1.06). However, electricity and gas as sources of energy for heating ranked second and third with mean usage level of 1.81 and 0.80 respectively. The study revealed that local people with the university education were significantly making higher use of electricity for both cooking and heating and those with no formal education ranked the highest on wood use for both cooking and heating. In addition, those living in traditional houses significantly used more wood for cooking than those living in villas and apartments. Also, local people with high income levels significantly were using more electricity for heating than others. The study recommended conducting extension and environmental awareness raising programs to enhance local residents’ adoption of wood substitutes, promoting employment opportunities for unemployed locals, and subsidizing prices of alternative energy sources. PMID:27081355

Highly Flexible and Efficient Solar Steam Generation Device.

PubMed

Chen, Chaoji; Li, Yiju; Song, Jianwei; Yang, Zhi; Kuang, Yudi; Hitz, Emily; Jia, Chao; Gong, Amy; Jiang, Feng; Zhu, J Y; Yang, Bao; Xie, Jia; Hu, Liangbing

2017-08-01

Solar steam generation with subsequent steam recondensation has been regarded as one of the most promising techniques to utilize the abundant solar energy and sea water or other unpurified water through water purification, desalination, and distillation. Although tremendous efforts have been dedicated to developing high-efficiency solar steam generation devices, challenges remain in terms of the relatively low efficiency, complicated fabrications, high cost, and inability to scale up. Here, inspired by the water transpiration behavior of trees, the use of carbon nanotube (CNT)-modified flexible wood membrane (F-Wood/CNTs) is demonstrated as a flexible, portable, recyclable, and efficient solar steam generation device for low-cost and scalable solar steam generation applications. Benefitting from the unique structural merits of the F-Wood/CNTs membrane-a black CNT-coated hair-like surface with excellent light absorbability, wood matrix with low thermal conductivity, hierarchical micro- and nanochannels for water pumping and escaping, solar steam generation device based on the F-Wood/CNTs membrane demonstrates a high efficiency of 81% at 10 kW cm -2 , representing one of the highest values ever-reported. The nature-inspired design concept in this study is straightforward and easily scalable, representing one of the most promising solutions for renewable and portable solar energy generation and other related phase-change applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Acoustic vibration analysis for utilization of woody plant in space environment

NASA Astrophysics Data System (ADS)

Chida, Yukari; Yamashita, Masamichi; Hashimoto, Hirofumi; Sato, Seigo; Tomita-Yokotani, Kaori; Baba, Keiichi; Suzuki, Toshisada; Motohashi, Kyohei; Sakurai, Naoki; Nakagawa-izumi, Akiko

2012-07-01

We are proposing to raise woody plants for space agriculture in Mars. Space agriculture has the utilization of wood in their ecosystem. Nobody knows the real tree shape grown under space environment under the low or micro gravitational conditions such as outer environment. Angiosperm tree forms tension wood for keeping their shape. Tension wood formation is deeply related to gravity, but the details of the mechanism of its formation has not yet been clarified. For clarifying the mechanism, the space experiment in international space station, ISS is the best way to investigate about them as the first step. It is necessary to establish the easy method for crews who examine the experiments at ISS. Here, we are proposing to investigate the possibility of the acoustic vibration analysis for the experiment at ISS. Two types of Japanese cherry tree, weeping and upright types in Prunus sp., were analyzed by the acoustic vibration method. Coefficient-of-variation (CV) of sound speed was calculated by the acoustic vibration analysis. The amount of lignin and decomposed lignin were estimated by both Klason and Py-GC/MS method, respectively. The relationships of the results of acoustic vibration analysis and the inner components in tested woody materials were investigated. After the experiments, we confirm the correlation about them. Our results indicated that the acoustic vibration analysis would be useful for determining the inside composition as a nondestructive method in outer space environment.

RESOLVE - Starting Point for Partnerships in Lunar and Mars Resource Characterization

NASA Technical Reports Server (NTRS)

Sanders, Gerald B.; Rosenbaum, Bernard; Simon, Thomas; Larson, William E.; Luecke, Dale; Captain, Jainine; Sacksteder, Kurt; Johnson, Kenneth R.; Boucher, Dale; Taylor, Jeffrey

2007-01-01

The mystery and controversy surrounding the possibility of finding water/ice at the lunar poles of the Moon based on the interpretation of neutron spectrometer data from Lunar Prospector and radar data from Clementine raises questions that both Science and the Human Exploration proponents want answered. From the Science perspective, the determination of lunar volatiles and in particular the increased hydrogen concentration detected at the lunar poles was identified as an important objectives for lunar exploration and understanding the history of the Moon, Sun, and the solar system. From the Human Exploration perspective, the potential for large concentrations of accessible water opens up possibilities for utilizing in-situ resources, known as In-Situ Resource Utilization (ISRU), to implement a sustained and affordable human exploration program of the Moon and beyond through production of propellants, fuel cell reagents, and life support consumables for lunar surface operations and mobility, and Earth-Moon transportation. Both the Science and Human Exploration proponents agree that a mission to the lunar poles to obtain ground truth data is the only means to conclusively answer the questions of whether water/ice exists, how much, what form, and where did it come from. In 2005, NASA initiated the Regolith and Environment Science & Oxygen and Lunar Volatiles Extraction (RESOLVE) project, and is currently developing hardware under the NASA Exploration Technology Development Program (ETDP). The purpose of the project was to begin developing technologies and operations that would answer the fundamental science questions, such as What resources are available on the Moon, where are they, what form, and where did they come from? as well as critical engineering questions, such as How will we mine these resources, what chemical extraction processes are the most practical and efficient, and what are the engineering challenges to be faced in this environment? .

Job safety analysis and hazard identification for work accident prevention in para rubber wood sawmills in southern Thailand.

PubMed

Thepaksorn, Phayong; Thongjerm, Supawan; Incharoen, Salee; Siriwong, Wattasit; Harada, Kouji; Koizumi, Akio

2017-11-25

We utilized job safety analysis (JSA) and hazard identification for work accident prevention in Para rubber wood sawmills, which aimed to investigate occupational health risk exposures and assess the health hazards at sawmills in the Trang Province, located in southern Thailand. We conducted a cross-sectional study which included a walk-through survey, JSA, occupational risk assessment, and environmental samplings from March through September 2015 at four Para rubber wood sawmills. We identified potential occupational safety and health hazards associated with six main processes, including: 1) logging and cutting, 2) sawing the lumber into sheets, 3) planing and re-arranging, 4) vacuuming and wood preservation, 5) drying and planks re-arranging, and 6) grading, packing, and storing. Working in sawmills was associated with high risk of wood dust and noise exposure, occupational accidents injuring hands and feet, chemicals and fungicide exposure, and injury due to poor ergonomics or repetitive work. Several high-risk areas were identified from JSA and hazard identification of the working processes, especially high wood dust and noise exposure when sawing lumber into sheets and risk of occupational accidents of the hands and feet when struck by lumber. All workers were strongly recommended to use personal protective equipment in any working processes. Exposures should be controlled using local ventilation systems and reducing noise transmission. We recommend that the results from the risk assessment performed in this study be used to create an action plan for reducing occupational health hazards in Para rubber sawmills.

Delignified and Densified Cellulose Bulk Materials with Excellent Tensile Properties for Sustainable Engineering.

PubMed

Frey, Marion; Widner, Daniel; Segmehl, Jana S; Casdorff, Kirstin; Keplinger, Tobias; Burgert, Ingo

2018-02-07

Today's materials research aims at excellent mechanical performance in combination with advanced functionality. In this regard, great progress has been made in tailoring the materials by assembly processes in bottom-up approaches. In the field of wood-derived materials, nanocellulose research has gained increasing attention, and materials with advanced properties were developed. However, there are still unresolved issues concerning upscaling for large-scale applications. Alternatively, the sophisticated hierarchical scaffold of wood can be utilized in a top-down approach to upscale functionalization, and one can profit at the same time from its renewable nature, CO 2 storing capacity, light weight, and good mechanical performance. Nevertheless, for bulk wood materials, a wider multipurpose industrial use is so far impeded by concerns regarding durability, natural heterogeneity as well as limitations in terms of functionalization, processing, and shaping. Here, we present a novel cellulose bulk material concept based on delignification and densification of wood resulting in a high-performance material. A delignification process using hydrogen peroxide and acetic acid was optimized to delignify the entire bulk wooden blocks and to retain the highly beneficial structural directionality of wood. In a subsequent step, these cellulosic blocks were densified in a process combining compression and lateral shear to gain a very compact cellulosic material with entangled fibers while retaining unidirectional fiber orientation. The cellulose bulk materials obtained by different densification protocols were structurally, chemically, and mechanically characterized revealing superior tensile properties compared to native wood. Furthermore, after delignification, the cellulose bulk material can be easily formed into different shapes, and the delignification facilitates functionalization of the bioscaffold.

Frankincense tapping reduces the carbohydrate storage of Boswellia trees.

PubMed

Mengistu, Tefera; Sterck, Frank J; Fetene, Masresha; Bongers, Frans

2013-06-01

Carbohydrates fixed by photosynthesis are stored in plant organs in the form of starch or sugars. Starch and sugars sum to the total non-structural carbohydrate pool (TNC) and may serve as intermediate pools between assimilation and utilization. We examined the impact of tapping on TNC concentrations in stem-wood, bark and root tissues of the frankincense tree (Boswellia papyrifera (Del.) Hochst) in two natural woodlands of Ethiopia. Two tapping treatments, one without tapping (control) and the other with tapping at 12 incisions, are applied on experimental trees. Trees are tapped in the leafless dry period, diminishing their carbon storage pools. If storage pools are not refilled by assimilation during the wet season, when crowns are in full leaf, tapping may deplete the carbon pool and weaken Boswellia trees. The highest soluble sugar concentrations were in the bark and the highest starch concentrations in the stem-wood. The stem-wood contains 12 times higher starch than soluble sugar concentrations. Hence, the highest TNC concentrations occurred in the stem-wood. Moreover, wood volume was larger than root or bark volumes and, as a result, more TNC was stored in the stem-wood. As predicted, tapping reduced the TNC concentrations and pool sizes in frankincense trees during the dry season. During the wet season, these carbon pools were gradually filled in tapped trees, but never to the size of non-tapped trees. We conclude that TNC is dynamic on a seasonal time scale and offers resilience against stress, highlighting its importance for tree carbon balance. But current resin tapping practices are intensive and may weaken Boswellia populations, jeopardizing future frankincense production.

Job safety analysis and hazard identification for work accident prevention in para rubber wood sawmills in southern Thailand

PubMed Central

Thepaksorn, Phayong; Thongjerm, Supawan; Incharoen, Salee; Siriwong, Wattasit; Harada, Kouji; Koizumi, Akio

2017-01-01

Objective: We utilized job safety analysis (JSA) and hazard identification for work accident prevention in Para rubber wood sawmills, which aimed to investigate occupational health risk exposures and assess the health hazards at sawmills in the Trang Province, located in southern Thailand. Methods: We conducted a cross-sectional study which included a walk-through survey, JSA, occupational risk assessment, and environmental samplings from March through September 2015 at four Para rubber wood sawmills. Results: We identified potential occupational safety and health hazards associated with six main processes, including: 1) logging and cutting, 2) sawing the lumber into sheets, 3) planing and re-arranging, 4) vacuuming and wood preservation, 5) drying and planks re-arranging, and 6) grading, packing, and storing. Working in sawmills was associated with high risk of wood dust and noise exposure, occupational accidents injuring hands and feet, chemicals and fungicide exposure, and injury due to poor ergonomics or repetitive work. Discussion: Several high-risk areas were identified from JSA and hazard identification of the working processes, especially high wood dust and noise exposure when sawing lumber into sheets and risk of occupational accidents of the hands and feet when struck by lumber. All workers were strongly recommended to use personal protective equipment in any working processes. Exposures should be controlled using local ventilation systems and reducing noise transmission. We recommend that the results from the risk assessment performed in this study be used to create an action plan for reducing occupational health hazards in Para rubber sawmills. PMID:28993571

Commercial activities and subsistence utilization of mangrove forests around the Wouri estuary and the Douala-Edea reserve (Cameroon).

PubMed

Atheull, Adolphe Nfotabong; Din, Ndongo; Longonje, Simon N; Koedam, Nico; Dahdouh-Guebas, Farid

2009-11-17

Worldwide there is growing research interest in the ethnobiology of mangrove forests. Notwithstanding that, little information has been published about ethnobiology of mangrove forests in Cameroon. The aims of this study were a) to analyze the harvesting methods and the local selling of mangrove wood products by loggers in the vicinity of Wouri estuary and b) to investigate the patterns of subsistence uses of mangrove wood products around the Douala-Edea reserve. Semi-structured interviews were conducted with 120 active mangrove loggers in 23 Douala wood markets and 103 households located in three villages (Mbiako, Yoyo I and Yoyo II) close to Douala-Edea reserve. In each of the three densely populated villages, every second household was chosen for sampling while in all markets, mangrove loggers were chosen randomly. In addition, log diameters were measured in each market using a wooden foldable tape measure. A post hoc analysis (Newman-Keuls test) was performed in order to detect the common wood class diameter sold in the Douala wood markets. The analysis of the loggers' survey data has shown that large logs of Rhizophora with diameter greater than 40 cm were common in the Douala wood markets and were more closely associated with loggers who used chainsaws. In addition to the general mangroves wood products selling, the analysis on a subsistence level (households' survey) suggests the local population's dependence on mangroves, with multiple uses of Rhizophora racemosa Meyer, R. harrisonii Leechman, Avicennia germinans L. Stearn., Laguncularia racemosa Gaertn. f. and Conocarpus erectus L. timbers for furniture, fences, smoking fish, and fuelwood. Finally, Nypa fruticans (Thunb.) Wurmb. leaves were used as thatching material for house walls and roofs. Our findings revealed that big logs of Rhizophora were commonly sold by the loggers. A majority of loggers (60%) reported that mangrove marketed wood constitute a principal source of income. Most of the villagers (85.83%) often depend on mangroves for subsistence needs and for them there is no substitute for mangrove wood. Therefore, more efforts should be undertaken at the national level to implement conservation, management and sustainable use of these coastal forests.

Thermochemical pretreatment of underutilized woody biomass for manufacturing wood composites

NASA Astrophysics Data System (ADS)

Pelaez Samaniego, Manuel Raul

Prescribed fires, one method for reducing hazardous fuel loads from forest lands in the US, are limited by geographical, environmental, and social impacts. Mechanical operations are an alternative type of fuel treatment but these processes are constrained by the difficulty of economically harvesting and/or using large amounts of low-value woody biomass. Adoption and integration of new technologies into existing wood composite facilities offer better utilization of this material. A pretreatment that enables integration of technologies in a typical composite facility will aid with diversification of product portfolio (e.g. wood composites, fuel pellets, liquid fuels, chemicals). Hot water extraction (HWE) is an option for wood pretreatment. This work provides a fundamental understanding of the physicochemical changes to wood resulting from HWE, and how these changes impact processing and performance of composites. Specific objectives were to: 1) review literature on studies related to the manufacture of composites produced with thermally pretreated wood, 2) manufacture wood plastic composites (WPC) and particleboard using HWE wood and evaluate the impacts of pretreatment on product properties, 3) develop an understanding of the effect of HWE on lignin properties, specifically lignin at the cells surface level after migration from cell walls and middle lamella, 4) discern the influence of lignin on the fiber surface on processing WPCs, and, 5) investigate the effect of changing the pretreatment environment (inert gas instead of water) on lignin behavior. Results show that HWE enhances the resistance of both WPCs and particleboard to water with positive or no effect on mechanical properties. Reduction of hemicelluloses and lignin property changes are suggested as the main reasons for enhancing interaction between wood fiber and resins during composite processing. Lignin on the surface of particles after HWE interacts with thermoplastics during WPCs compounding, thus improving bond quality between the constituents and maintaining the mechanical properties of the composites. The amount and properties of lignin on the fiber surfaces depends on the pretreatment conditions. Thus, it seems possible to control the pretreatment process to increase or decrease the amount of lignin on particles surfaces, which is of great interest for managing downstream processes within biorefinery concepts.

Commercial activities and subsistence utilization of mangrove forests around the Wouri estuary and the Douala-Edea reserve (Cameroon)

PubMed Central

2009-01-01

Background Worldwide there is growing research interest in the ethnobiology of mangrove forests. Notwithstanding that, little information has been published about ethnobiology of mangrove forests in Cameroon. The aims of this study were a) to analyze the harvesting methods and the local selling of mangrove wood products by loggers in the vicinity of Wouri estuary and b) to investigate the patterns of subsistence uses of mangrove wood products around the Douala-Edea reserve. Methods Semi-structured interviews were conducted with 120 active mangrove loggers in 23 Douala wood markets and 103 households located in three villages (Mbiako, Yoyo I and Yoyo II) close to Douala-Edea reserve. In each of the three densely populated villages, every second household was chosen for sampling while in all markets, mangrove loggers were chosen randomly. In addition, log diameters were measured in each market using a wooden foldable tape measure. A post hoc analysis (Newman-Keuls test) was performed in order to detect the common wood class diameter sold in the Douala wood markets. Results The analysis of the loggers' survey data has shown that large logs of Rhizophora with diameter greater than 40 cm were common in the Douala wood markets and were more closely associated with loggers who used chainsaws. In addition to the general mangroves wood products selling, the analysis on a subsistence level (households' survey) suggests the local population's dependence on mangroves, with multiple uses of Rhizophora racemosa Meyer, R. harrisonii Leechman, Avicennia germinans L. Stearn., Laguncularia racemosa Gaertn. f. and Conocarpus erectus L. timbers for furniture, fences, smoking fish, and fuelwood. Finally, Nypa fruticans (Thunb.) Wurmb. leaves were used as thatching material for house walls and roofs. Conclusion Our findings revealed that big logs of Rhizophora were commonly sold by the loggers. A majority of loggers (60%) reported that mangrove marketed wood constitute a principal source of income. Most of the villagers (85.83%) often depend on mangroves for subsistence needs and for them there is no substitute for mangrove wood. Therefore, more efforts should be undertaken at the national level to implement conservation, management and sustainable use of these coastal forests. PMID:19919680

Torrefaction of wood pellets: New solutions

NASA Astrophysics Data System (ADS)

Zaichenko, V. M.; Shterenberg, V. Ya.

2017-10-01

The current state of the market of conventional and torrefied wood pellets and the trends of its development have been analyzed. The advantages and disadvantages of pellets of both types have been compared with other alternative fuels. The consumer segment in which wood pellets are the most competitive has been determined. The original torrefaction technology using exhaust gas heat from a standard gas engine that was developed at the Joint Institute for High Technologies and the scheme of an experimental unit for the elaboration of the technology have been presented. The scheme of the combined operation of a torrefaction unit and a standard hot water boiler, which makes it possible to utilize the heat of exhaust steam-and-gas products of torrefaction with the simultaneous prevention of emissions of harmful substances into the environment, has been proposed. The required correlation between the capacity of the torrefaction unit and the heating boiler house has been estimated for optimal operation under the conditions of the isolated urban village in a region that is distant from the areas of extraction of traditional fuels and, at the same time, has quite sufficient resources of raw materials for the production of wood pellets.

Tin anode for sodium-ion batteries using natural wood fiber as a mechanical buffer and electrolyte reservoir.

PubMed

Zhu, Hongli; Jia, Zheng; Chen, Yuchen; Weadock, Nicholas; Wan, Jiayu; Vaaland, Oeyvind; Han, Xiaogang; Li, Teng; Hu, Liangbing

2013-07-10

Sodium (Na)-ion batteries offer an attractive option for low cost grid scale storage due to the abundance of Na. Tin (Sn) is touted as a high capacity anode for Na-ion batteries with a high theoretical capacity of 847 mAh/g, but it has several limitations such as large volume expansion with cycling, slow kinetics, and unstable solid electrolyte interphase (SEI) formation. In this article, we demonstrate that an anode consisting of a Sn thin film deposited on a hierarchical wood fiber substrate simultaneously addresses all the challenges associated with Sn anodes. The soft nature of wood fibers effectively releases the mechanical stresses associated with the sodiation process, and the mesoporous structure functions as an electrolyte reservoir that allows for ion transport through the outer and inner surface of the fiber. These properties are confirmed experimentally and computationally. A stable cycling performance of 400 cycles with an initial capacity of 339 mAh/g is demonstrated; a significant improvement over other reported Sn nanostructures. The soft and mesoporous wood fiber substrate can be utilized as a new platform for low cost Na-ion batteries.

UTILIZATION OF SCRAP PREPREG WASTES AS A REINFORCEMENT IN A WHOLLY RECYCLED PLASTIC - PHASE II

EPA Science Inventory

Foster-Miller is proposing to combine Municipal Solid Waste (MSW) commingled plastics with a high performance reinforcement (scrap prepreg) to form a durable and cost competitive wood substitute with superior moisture, rodent and insect resistance. This proposed technology ...

Utility of acoustical detection of Coptotermes Formosanus (Isoptera: Rhinotermitidae)

USDA-ARS?s Scientific Manuscript database

The AED 2000 and 2010 are extremely sensitive listening devices which can effectively detect and monitor termite activity through a wave guide (e.g. bolt) both qualitatively and quantitatively. Experiments conducted with one to ten thousand termites from differing colonies infesting wood in buckets...

Synthesis of polymers from liquefied biomass and their utilization in wood bonding

USDA-ARS?s Scientific Manuscript database

As the sustainable manufacturing concept becomes a mandatory requirement, more and more researchers have devoted to converting biomass as components for polymer or as a substitution for part of petroleum based polymers for different applications. Agricultural and forestry lignocellulosic biomass mat...

Advanced processing methods to introduce and preserve dipole orientation in organic electro-optic materials for next generation photonic devices

NASA Astrophysics Data System (ADS)

Huang, Su

Organic electro-optic (E-O) materials have attracted considerable research attention in the past 20 years due to their rising potentials in a lot of novel photonic applications, such as high-speed telecommunication, terahertz generation and ultra-fast optical interconnections. Chapter 2 of this dissertation focuses on a barrier layer approach to improve the poling efficiency of electro-optic polymers. First of all, high conduction current from excessive charge injection is identified as a fundamental challenge of effective poling. After analyzing the conduction mechanism, we introduce a sol-gel derived thin titanium dioxide (TiO2) layer that can significantly block excessive charge injection and reduce the leakage current during high field poling. Ultralarge E-O coefficients, up to 160-350 pm/V at 1310 nm have been achieved by poling with such a barrier, which are 26%-40% higher than the results poled without such a TiO2 layer. This enhancement is explained by the suppressed charge injection and space charge accumulation by the insertion of the high injection barrier from the TiO2 barrier layer. In Chapter 3, the impact of the inserted barrier layer on the temporal alignment stability of E-O polymers is discussed. Considerable stability enhancement is confirmed using both standard 500-hour temporal alignment stability test at 85 °C and thermally stimulated discharge method. We suggest that the enhancement comes from improved stability of the screening charge. During poling the additional barrier layer helps to lower the injection and thus the space charge accumulation. And this reduced space charge accumulation further helps to replace the space charge part in the total formulation of screening charge with more stable interface trapped charge. We thus expand this knowledge to a group of other materials that can also block excessive charge injection and suppressed space charge accumulation, including dielectric polymers polyvinyl alcohol (PVA), poly(4-vinylphenol) (PVP) and TOPAS as well as ferroelectric polymer poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE), 65/35 copolymer), which differ largely from the others in dielectric constant, conductivity and surface properties. The only common feature of them is that they all lowered the charge injection and leakage current for 1-2 orders during poling. On every buffer layer we tried, similar trend of stability enhancement is found. These results suggest that the observed temporal stability enhancement is indeed an effect from the abovementioned mechanism. Chapter 4 focuses on the development of an innovative new poling method, which utilizes pyroelectric effect instead of external power sources to overcome the limitations of conventional contact poling and corona poling. With careful theory assisted design, we developed a reliable protocol to efficiently introduce dipole orientation in organic E-O materials by heating and cooling them with detachable pyroelectric crystals. This new method can potentially improve the process adaptability of organic E-O materials in a variety of photonic devices. Large Pockels coefficients (up to 81 pm/V at 1.3 micron) have been successfully achieved in thin films poled using this method. The effective fields in these experiments are estimated to be around 0.5 to 0.9 MV/cm, which agree well with the electrostatics analysis using an idealized model. The same method is directly applied to surface modified hybrid polymer silicon slot waveguide ring-resonator modulators devices. A 25 pm/V tunability of resonance peak wavelength shift has been realized, which was higher than any reported results in similar devices. Chapter 5 discusses about the possible application of the pyroelectric poling in a multi-stack waveguide device architecture. A long-existing challenge to pole E-O polymer based photonic devices is how to effectively drop the poling voltage to the core layer, which is usually sandwiched between two dielectric claddings. In the past, this was done by using relatively conductive claddings, which on the other hand can bring larger optical loss and dielectric loss to the waveguide. Thus careful engineering compromise must be made between better poling efficiency and lower loss. Pyroelectric poling as discussed in Chapter 4 opens up new possibilities. In this chapter, it is demonstrated that E-O polymer films can be poled even with 3 orders thicker dielectric layer in circuit using pyroelectric poling. The theoretical analysis matches well with the experimental results. (Abstract shortened by UMI.).

Regulation of spindle integrity and mitotic fidelity by BCCIP

PubMed Central

Huhn, S C; Liu, J; Ye, C; Lu, H; Jiang, X; Feng, X; Ganesan, S; White, E; Shen, Z

2017-01-01

Centrosomes together with the mitotic spindle ensure the faithful distribution of chromosomes between daughter cells, and spindle orientation is a major determinant of cell fate during tissue regeneration. Spindle defects are not only an impetus of chromosome instability but are also a cause of developmental disorders involving defective asymmetric cell division. In this work, we demonstrate BCCIP, especially BCCIPα, as a previously unidentified component of the mitotic spindle pole and the centrosome. We demonstrate that BCCIP localizes proximal to the mother centriole and participates in microtubule organization and then redistributes to the spindle pole to ensure faithful spindle architecture. We find that BCCIP depletion leads to morphological defects, disoriented mitotic spindles, chromosome congression defects and delayed mitotic progression. Our study identifies BCCIP as a novel factor critical for microtubule regulation and explicates a mechanism utilized by BCCIP in tumor suppression. PMID:28394342

Ferroelectric domain building blocks for photonic and nonlinear optical microstructures in LiNbO3

NASA Astrophysics Data System (ADS)

Zisis, G.; Ying, C. Y. J.; Soergel, E.; Mailis, S.

2014-03-01

The ability to manipulate the size and depth of poling inhibited domains, which are produced by UV laser irradiation of the +z face of lithium niobate crystals followed by electric field poling, is demonstrated. It is shown that complex domain structures, much wider than the irradiating laser spot, can be obtained by partially overlapping the subsequent UV laser irradiated tracks. The result of this stitching process is one uniform domain without any remaining trace of its constituent components thus increasing dramatically the utility of this method for the fabrication of surface microstructures as well as periodic and aperiodic domain lattices for nonlinear optical and surface acoustic wave applications. Finally, the impact of multi exposure on the domain characteristics is also investigated indicating that some control over the domain depth can be attained.

Low loss pole configuration for multi-pole homopolar magnetic bearings

NASA Technical Reports Server (NTRS)

Blumenstock, Kenneth A. (Inventor); Hakun, Claef F. (Inventor)

2001-01-01

A new pole configuration for multi-pole homopolar bearings proposed in this invention reduces rotational losses caused by eddy-currents generated when non-uniform flux distributions exist along the rotor surfaces. The new homopolar magnetic bearing includes a stator with reduced pole-to-pole and exhibits a much more uniform rotor flux than with large pole-to-pole gaps. A pole feature called a pole-link is incorporated into the low-loss poles to provide a uniform pole-to-pole gap and a controlled path for pole-to-pole flux. In order to implement the low-loss pole configuration of magnetic bearings with small pole-to-pole gaps, a new stator configuration was developed to facilitate installation of coil windings. The stator was divided into sector shaped pieces, as many pieces as there are poles. Each sector-shaped pole-piece can be wound on a standard coil winding machine, and it is practical to wind precision layer wound coils. To achieve maximum actuation efficiency, it is desirable to use all the available space for the coil formed by the natural geometric configuration. Then, the coils can be wound in a tapered shape. After winding, the sectored-pole-pieces are installed into and fastened by bonding or other means, to a ring of material which encloses the sectored-pole-pieces, forming a complete stator.

Reproductive Performance of a Declining Forest Passerine in Relation to Environmental and Social Factors: Implications for Species Conservation

PubMed Central

Grendelmeier, Alex; Arlettaz, Raphaël; Gerber, Michael; Pasinelli, Gilberto

2015-01-01

Identifying factors influencing a species' ecological niche and demography is a prerequisite for species conservation. However, our understanding of the interplay between demographic rates and biotic/abiotic factors is still poor for most species of conservation concern. We evaluated relevance of eight hypotheses relating to timing of breeding, temporal nest exposure, nest concealment, topography, tree structure, predation risk and disturbance, density dependence and weather for explaining variation in reproductive performance of the declining wood warbler Phylloscopus sibilatrix in northern Switzerland. Reproductive performance was monitored with cameras at 136 nests from 2010 to 2012 and was associated to temporal exposure, timing of breeding and concealment of nests. Daily nest survival was positively related to the number of grass and sedge tussocks, nest concealment and nest age. Clutch size and number of fledglings decreased, the later in the season a nest was initiated. Nest survival over an average nesting period of 31 days was 46.9 ± 0.07% (mean ± SE), daily nest survival rate was 0.976 ± 0.002. As for many ground-breeding birds, nest predation was the principal cause of nest failure, accounting for 79% of all nest losses. Conservation measures should aim at increasing the area of relatively homogenous forest stands featuring suitable habitats characterized by abundant and accessible grass and sedge tussocks. In managed forests, such conditions can be found in stands of middle age (i.e. pole wood) with little to no shrub layer. PMID:26172954

Reproductive Performance of a Declining Forest Passerine in Relation to Environmental and Social Factors: Implications for Species Conservation.

PubMed

Grendelmeier, Alex; Arlettaz, Raphaël; Gerber, Michael; Pasinelli, Gilberto

2015-01-01

Identifying factors influencing a species' ecological niche and demography is a prerequisite for species conservation. However, our understanding of the interplay between demographic rates and biotic/abiotic factors is still poor for most species of conservation concern. We evaluated relevance of eight hypotheses relating to timing of breeding, temporal nest exposure, nest concealment, topography, tree structure, predation risk and disturbance, density dependence and weather for explaining variation in reproductive performance of the declining wood warbler Phylloscopus sibilatrix in northern Switzerland. Reproductive performance was monitored with cameras at 136 nests from 2010 to 2012 and was associated to temporal exposure, timing of breeding and concealment of nests. Daily nest survival was positively related to the number of grass and sedge tussocks, nest concealment and nest age. Clutch size and number of fledglings decreased, the later in the season a nest was initiated. Nest survival over an average nesting period of 31 days was 46.9 ± 0.07% (mean ± SE), daily nest survival rate was 0.976 ± 0.002. As for many ground-breeding birds, nest predation was the principal cause of nest failure, accounting for 79% of all nest losses. Conservation measures should aim at increasing the area of relatively homogenous forest stands featuring suitable habitats characterized by abundant and accessible grass and sedge tussocks. In managed forests, such conditions can be found in stands of middle age (i.e. pole wood) with little to no shrub layer.

A look at black walnut timber resources and industries

Treesearch

Kenneth L. Quigley; Roland D. Lindmark

1967-01-01

Our Black Walnut tree (Juglans nigra L.) has always had top rank among trees in America. It claims its rank on two counts: it is one of our major nut trees; and its wood has a beauty and utility that few other trees can match.

Forestry: Program Planning Guide: Volume 7.

ERIC Educational Resources Information Center

Roth, Paul L.; And Others

The program planning guide for forestry was written to assist Applied Biological and Agricultural Occupations (ABAO) teachers in enriching existing programs and/or to provide the basis for expansion of offerings to include additional materials for the cluster areas of forests, forest protection, logging, wood utilization, recreation, and special…

Emerging Energy Alternatives for the Southeastern States

NASA Technical Reports Server (NTRS)

Stefanakos, E. K. (Editor)

1978-01-01

The proceedings of the first symposium on emerging energy alternatives for the Southeastern States are presented. Some topics discussed are: (1) solar energy, (2) wood energy, (3) novel energy sources, (4) agricultural and industrial process heat, (5) waste utilization, (6) energy conservation and (7) ocean thermal energy conversion.

Understanding Materials

ERIC Educational Resources Information Center

Katsioloudis, Petros J.

2010-01-01

Almost everything people have ever done has involved materials. Historical evidence indicates that "engineered materials" have been available and utilized for the benefit of humankind since the Neolithic period, beginning about 10,000 BC. Some of these materials have been in existence for thousands of years. At first, materials consisted of wood,…

MEMS, Ka-Band Single-Pole Double-Throw (SPDT) Switch for Switched Line Phase Shifters

NASA Technical Reports Server (NTRS)

Scardelletti, Maximilian C.; Ponchak, George E.; Varaljay, Nicholas C.

2002-01-01

Ka-band MEMS doubly anchored cantilever beam capacitive shunt devices are used to demonstrate a MEMS SPDT switch fabricated on high resistivity silicon (HRS) utilizing finite ground coplanar waveguide (FGC) transmission lines. The SPDT switch has an insertion loss (IL), return loss (RL), and isolation of 0.3dB, 40dB, and 30 dB, respectively at Ka-band.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing newly designed launch and entry suit (LES), floats in single-occupant life raft during simulations in the JSC Weightless Environment Training Facility Bldg 29 pool. During the simulation of escape and rescue operations, the crew escape system (CES) pole mode of egress from the Space Shuttle was utilized.

PopZ identifies the new pole, and PodJ identifies the old pole during polar growth in Agrobacterium tumefaciens

PubMed Central

Grangeon, Romain; Zupan, John R.; Anderson-Furgeson, James; Zambryski, Patricia C.

2015-01-01

Agrobacterium tumefaciens elongates by addition of peptidoglycan (PG) only at the pole created by cell division, the growth pole, whereas the opposite pole, the old pole, is inactive for PG synthesis. How Agrobacterium assigns and maintains pole asymmetry is not understood. Here, we investigated whether polar growth is correlated with novel pole-specific localization of proteins implicated in a variety of growth and cell division pathways. The cell cycle of A. tumefaciens was monitored by time-lapse and superresolution microscopy to image the localization of A. tumefaciens homologs of proteins involved in cell division, PG synthesis and pole identity. FtsZ and FtsA accumulate at the growth pole during elongation, and improved imaging reveals FtsZ disappears from the growth pole and accumulates at the midcell before FtsA. The L,D-transpeptidase Atu0845 was detected mainly at the growth pole. A. tumefaciens specific pole-organizing protein (Pop) PopZAt and polar organelle development (Pod) protein PodJAt exhibited dynamic yet distinct behavior. PopZAt was found exclusively at the growing pole and quickly switches to the new growth poles of both siblings immediately after septation. PodJAt is initially at the old pole but then also accumulates at the growth pole as the cell cycle progresses suggesting that PodJAt may mediate the transition of the growth pole to an old pole. Thus, PopZAt is a marker for growth pole identity, whereas PodJAt identifies the old pole. PMID:26324921

Weatherability and Leach Resistance of Wood Impregnated with Nano-Zinc Oxide

NASA Astrophysics Data System (ADS)

Clausen, Carol A.; Green, Frederick; Nami Kartal, S.

2010-09-01

Southern pine specimens vacuum-treated with nano-zinc oxide (nano-ZnO) dispersions were evaluated for leach resistance and UV protection. Virtually, no leaching occurred in any of the nano-ZnO-treated specimens in a laboratory leach test, even at the highest retention of 13 kg/m3. However, specimens treated with high concentrations of nano-ZnO showed 58-65% chemical depletion after 12 months of outdoor exposure. Protection from UV damage after 12 months exposure is visibly obvious on both exposed and unexposed surfaces compared to untreated controls. Graying was markedly diminished, although checking occurred in all specimens. Nano-zinc oxide treatment at a concentration of 2.5% or greater provided substantial resistance to water absorption following 12 months of outdoor exposure compared to untreated and unweathered southern pine. We conclude that nano-zinc oxide can be utilized in new wood preservative formulations to impart resistance to leaching, water absorption and UV damage of wood.

Enhanced hydroxyl radical production by dihydroxybenzene-driven Fenton reactions: implications for wood biodegradation.

PubMed

Contreras, David; Rodríguez, Jaime; Freer, Juanita; Schwederski, Brigitte; Kaim, Wolfgang

2007-09-01

Brown rot fungi degrade wood, in initial stages, mainly through hydroxyl radicals (.OH) produced by Fenton reactions. These Fenton reactions can be promoted by dihydroxybenzenes (DHBs), which can chelate and reduce Fe(III), increasing the reactivity for different substrates. This mechanism allows the extensive degradation of carbohydrates and the oxidation of lignin during wood biodegradation by brown rot fungi. To understand the enhanced reactivity in these systems, kinetics experiments were carried out, measuring .OH formation by the spin-trapping technique of electron paramagnetic resonance spectroscopy. As models of the fungal DHBs, 1,2-dihydroxybenzene (catechol), 2,3-dihydroxybenzoic acid and 3,4-dihydroxybenzoic acid were utilized as well as 1,2-dihydroxy-3,5-benzenedisulfonate as a non-Fe(III)-reducing substance for comparison. Higher amounts and maintained concentrations of .OH were observed in the driven Fenton reactions versus the unmodified Fenton process. A linear correlation between the logarithms of complex stability constants and the .OH production was observed, suggesting participation of such complexes in the radical production.

New Techniques in Characterization of Ferroelectric Materials

NASA Technical Reports Server (NTRS)

Sehirlioglu, Alp

2008-01-01

Two new techniques have been developed to characterize Pb(Mg1/3Nb2/3)O3-PbTiO3 (PMN-PT) based ferroelectric single crystals: (i) electro-thermal imaging, and (ii) single crystal x-ray diffraction in the transmission mode. (i) Electro-thermal imaging is a remote sensing technique that can detect the polarization direction and poling state of a whole crystal slice. This imaging technique utilizes an IR camera to determine the field induced temperature change and does not require any special or destructive sample preparation. In the resulting images it is possible to distinguish regions of 180 deg domains. This powerful technique can be used remotely during poling to determine the poling state of the crystal to avoid over-poling that can result in inferior properties and/or cracking of the crystals. Electro-thermal imaging produced the first direct observations of polarization rotation. Under bipolar field, the domains near the corners were the first to switch direction. As the field increased above the coercive field, domains at the center part of the crystals switched direction. (ii) X-ray diffraction in the transmission mode has long been used in structure determination of organic crystals and proteins; however, it is not used much to characterize inorganic systems. 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 single crystals were examined by this XRD technique for the first time, and a never-before-seen super-lattice was revealed with a doubling of the unit cell in all three directions, giving a cell volume eight times that of a traditional perovskite unit cell. The significance of the super-lattice peaks increased with poling, indicating a structural contribution to ordering. Lack of such observations by electron diffraction in the transmission electron microscope examinations suggests the presence of a bulk effect.

Capacitance Sensors for Nondestructive Moisture Determination in Agricultural and Bio-fuel materials

USDA-ARS?s Scientific Manuscript database

Moisture content of wood chips, pellets, switch grass powders, and similar organic bio-fuel materials is an important property to be known to determine their utility and energy efficiency at various stages of their processing and storage. Several moisture measuring instruments are available in the m...

GaAs Monolithic Microwave Subsystem Technology Base

DTIC Science & Technology

1980-01-01

To provide a captive source of reliable, high-quality GaAs substrates, a new crystal growth and substrate preparation facility which utilizes a high...Symp. GaAs and Related Compounds, Inst. Phys. Conf. Ser. 24, 6. 20. Wood, Woodcock and Harris (1978) GaAs and Related Compounds, Inst. Phys. Conf

The Little-Known Crisis

ERIC Educational Resources Information Center

Eckholm, Erik P.

1975-01-01

For one-third of the world's people, the energy crisis means the daily scramble to find the wood they need to cook. The accelerating destruction of forests throughout Africa, Asia and Latin America and the utilization of manure as a firewood substitute may produce the most profound ecological crisis of this century. (BT)

Growing Eucalypts in Florida for Industrial Wood Production

Treesearch

T.F. Geary; G.F. Meskimen; E.C. Franklin

1983-01-01

Eucalypt planting is practical on many sites in southern Florida, and strains resistant to freezes farther north are being bred. Methods have been developed for tree improvement, seed collection and handling, nursery management, plantation establishment and protection,and coppice regeneration.Guides to yields and utilization have been produced.

A STUDY OF THE FEASIBILITY OF UTILIZING SOLID WASTES FOR BUILDING MATERIALS. PHASE III AND IV SUMMARY REPORTS

EPA Science Inventory

This report summarizes work to develop building materials containing inorganic and organic wastes and wastes-derived products. Attempts were made to produce full-scale products and qualify them for structural applications. Particle board panels were made of peanut hulls and wood ...

Low-Capital Systems for Thinning Pine Plantations

Treesearch

John Wilhoit; Qingyue Ling; Robert Rummer

1999-01-01

Highly mechanized systems utilizing rubber-tired skidders, feller-bunchers, and knuckleboom loaders are the predominant type of timber harvesting operation in the southern United States. These systems, which handle the wood in tree-length form, are highly productive and very efficient, especially for large tracts of timber. Thinnings constitute an increasing proportion...

Edge-glued panels from Alaska hardwoods: retail manager perspectives

Treesearch

David Nicholls; Matthew Bumgardner; Valerie Barber

2010-01-01

In Alaska, red alder (Alnus rubra Bong.) and paper birch (Betula papyrifera Marsh.) are both lesser-known hardwoods grown, harvested, and manufactured into appearance products, with potential for increased utilization. The production of edgeglued panels from red alder and paper birch offers one expansion opportunity for wood...

Wood for structural and architectural purposes

Treesearch

C.W. Boyd; P. Koch; H.B. MeKean; C.R. Morschauser; S.B. Preston; F.F. Wangaard

1976-01-01

In recent years major emphasis has been placed on nonrenewable resources in relation to potential national problems that may arise from possible changes in materials supply or utilization. Renewable resources, however, have received disproportionately small attention in spite of their current importance as industrial raw materials and their potential for the future. In...

Lignocellulosic composites prepared utilizing aqueous alkaline/urea solutions with cold temperatures

USDA-ARS?s Scientific Manuscript database

Lignocellulosic composites (LCs) were fabricated by partially dissolving cotton to create a matrix that was reinforced with Osage orange wood (OOW) particles and/or Blue agave fibers (AF). LCs were composed of 15-35% cotton matrix: 65-85% OWW/AF reinforcement. The matrix was produced by soaking cott...

Chemical methods in the development of eco-efficient wood-based pellet production and technology.

PubMed

Kuokkanen, Matti; Kuokkanen, Toivo; Stoor, Tuomas; Niinimäki, Jouko; Pohjonen, Veli

2009-09-01

Up to 20 million tons of waste wood biomass per year is left unused in Finland, mainly in the forests during forestry operations, because supply and demand does not meet. As a consequence of high heat energy prices, the looming threat of climate change, the greenhouse effect, and due to global as well as national demands to considerably increase the proportion of renewable energy, there is currently tremendous enthusiasm in Finland to substantially increase pellet production. As part of this European objective to increase the eco- and cost-efficient utilization of bio-energy from the European forest belt, the aim of our research group is - by means of multidisciplinary research, especially through chemical methods - to promote the development of Nordic wood-based pellet production in both the qualitative and the quantitative sense. Wood-based pellets are classified as an emission-neutral fuel, which means that they are free from emission trading in the European Union. The main fields of pellet research and the chemical toolbox that has been developed for these studies, which includes a new specific staining and optical microscope method designed to determine the cross-linking of pellets in the presence of various binding compounds, are described in this paper. As model examples illustrating the benefits of this toolbox, experimental data is presented concerning Finnish wood pellets and corresponding wood-based pellets that include the use of starch-containing waste potato peel residue and commercial lignosulfonate as binding materials. The initial results concerning the use of the developed and optimized specific staining and microscopic method using starch-containing potato peel residue as binding material are presented.

Impact of Thermal Pretreatment Temperatures on Woody Biomass Chemical Composition, Physical Properties and Microstructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Ping; Howard, Bret H.

Thermal pretreatment of biomass by torrefaction and low temperature pyrolysis has the potential for generating high quality and more suitable fuels. To utilize a model to describe the complex and dynamic changes taking place during these two treatments for process design, optimization and scale-up, detailed data is needed on the property evolution during treatment of well-defined individual biomass particles. The objectives of this study are to investigate the influence of thermal pretreatment temperatures on wood biomass biochemical compositions, physical properties and microstructure. Wild cherry wood was selected as a model biomass and prepared for this study. The well-defined wood particlemore » samples were consecutively heated at 220, 260, 300, 350, 450 and 550 °C for 0.5 h under nitrogen. Untreated and treated samples were characterized for biochemical composition changes (cellulose, hemicellulose, and lignin) by thermogravimetric analyzer (TGA), physical properties (color, dimensions, weight, density and grindablity), chemical property (proximate analysis and heating value) and microstructural changes by scanning electron microscopy (SEM). Hemicellulose was mostly decomposed in the samples treated at 260 and 300 °C and resulted in the cell walls weakening resulting in improved grindability. The dimensions of the wood were reduced in all directions and shrinkage increased with increased treatment temperature and weight loss. With increased treatment temperature, losses of weight and volume increased and bulk density decreased. The low temperature pyrolyzed wood samples improved solid fuel property with high fuel ratio, which are close to lignite/bituminous coal. Morphology of the wood remained intact through the treatment range but the cell walls were thinner. Lastly, these results will improve the understanding of the property changes of the biomass during pretreatment and will help to develop models for process simulation and potential application of the treated biomass.« less

Impact of Thermal Pretreatment Temperatures on Woody Biomass Chemical Composition, Physical Properties and Microstructure

DOE PAGES

Wang, Ping; Howard, Bret H.

2017-12-23

Thermal pretreatment of biomass by torrefaction and low temperature pyrolysis has the potential for generating high quality and more suitable fuels. To utilize a model to describe the complex and dynamic changes taking place during these two treatments for process design, optimization and scale-up, detailed data is needed on the property evolution during treatment of well-defined individual biomass particles. The objectives of this study are to investigate the influence of thermal pretreatment temperatures on wood biomass biochemical compositions, physical properties and microstructure. Wild cherry wood was selected as a model biomass and prepared for this study. The well-defined wood particlemore » samples were consecutively heated at 220, 260, 300, 350, 450 and 550 °C for 0.5 h under nitrogen. Untreated and treated samples were characterized for biochemical composition changes (cellulose, hemicellulose, and lignin) by thermogravimetric analyzer (TGA), physical properties (color, dimensions, weight, density and grindablity), chemical property (proximate analysis and heating value) and microstructural changes by scanning electron microscopy (SEM). Hemicellulose was mostly decomposed in the samples treated at 260 and 300 °C and resulted in the cell walls weakening resulting in improved grindability. The dimensions of the wood were reduced in all directions and shrinkage increased with increased treatment temperature and weight loss. With increased treatment temperature, losses of weight and volume increased and bulk density decreased. The low temperature pyrolyzed wood samples improved solid fuel property with high fuel ratio, which are close to lignite/bituminous coal. Morphology of the wood remained intact through the treatment range but the cell walls were thinner. Lastly, these results will improve the understanding of the property changes of the biomass during pretreatment and will help to develop models for process simulation and potential application of the treated biomass.« less

Utility Monitoring and Control System (UMCS) and Utility Metering Plan and Specifications for Fort Leonard Wood, MO

DTIC Science & Technology

2017-06-22

setup” versus “use” issue. What rights does Honeywell need to run the software? We/Honeywell may not know. Discuss with Jabe? We may need to just try...Summary: It appears the direction we are going will be to install new me- ters in buildings, connect them to the Smart Servers, run the data through...damper blade type (check the appropriate item) Flat late Airfoil Calculate the nominal damper face velocity Face velocity = Flow rate ÷ Area

Method using selected carbons to react with Al2O and Al vapors in the carbothermic production of aluminum

DOEpatents

Fruehan, Richard J.; Li, Yun; Carkin, Gerald

2005-02-01

In a method for recovering Al from an off-gas (3,4) produced during carbothermic reduction of aluminum utilizing at least one smelter (1,2), the off-gas (3,4) is directed to an enclosed reactor (5) which is fed a supply of wood charcoal (7) having a porosity of from about 50 vol. % to 85 vol. % and an average pore diameter of from about 0.05 .mu.m to about 2.00 .mu.m, where the wood charcoal (7) contacts the off-gas (3,4) to produce at least Al.sub.4 C.sub.3 (6), which is passed back to the smelter (1,2).

The effects of heat treatment on physical properties and surface roughness of red-bud maple (Acer trautvetteri Medw.) wood.

PubMed

Korkut, Derya Sevim; Guller, Bilgin

2008-05-01

Heat treatment is often used to improve the dimensional stability of wood. In this study, the effects of heat treatment on physical properties and surface roughness of red-bud maple (Acer trautvetteri Medw.) wood were examined. Samples obtained from Düzce Forest Enterprises, Turkey, were subjected to heat treatment at varying temperatures and durations. The physical properties of heat-treated samples were compared against controls in order to determine their; oven-dry density, air-dry density, and swelling properties. A stylus method was employed to evaluate the surface characteristics of the samples. Roughness measurements, using the stylus method, were made in the direction perpendicular to the fiber. Three main roughness parameters; mean arithmetic deviation of profile (Ra), mean peak-to-valley height (Rz), and maximum roughness (Rmax) obtained from the surface of wood, were used to evaluate the effect of heat treatment on the surface characteristics of the specimens. Significant differences were determined (p>0.05) between surface roughness parameters (Ra, Rz, Rmax) at three different temperatures and three periods of heat treatment. The results showed that the values of density, swelling and surface roughness decreased with increasing temperature treatment and treatment times. Red-bud maple wood could be utilized successfully by applying proper heat treatment techniques without any losses in investigated parameters. This is vital in areas, such as window frames, where working stability and surface smoothness are important factors.

Passive microwave device applications of high T(c) superconducting thin films

NASA Astrophysics Data System (ADS)

Lyons, W. G.; Withers, R. S.

1990-11-01

Superconductors with a transition temperature T(c) from 40 K to 125 K are analyzed, with focus placed on their behavior around the boiling point of liquid nitrogen (77 K). It is shown that high-T(c) superconductors are similar to conventional type-II superconductors with paired holes instead of paired electrons. The nature of the electromagnetic response of a superconductor is illustrated with a two-fluid model, and surface resistance and conductor loss are assessed. Several microwave applications of high-T(c) superconductors are outlined including a six-pole dielectric loaded cavity filter used in multiplexers on current communication satellites and a four-pole superconducting filter. An implementation of a chirp filter using superconducting striplines with a cascaded array of backward-wave couplers to achieve a downchirp is presented as well as a 60-GHz phased antenna utilizing microstrip lines in the feed network.

New frontiers: discovering cilia-independent functions of cilia proteins.

PubMed

Vertii, Anastassiia; Bright, Alison; Delaval, Benedicte; Hehnly, Heidi; Doxsey, Stephen

2015-10-01

In most vertebrates, mitotic spindles and primary cilia arise from a common origin, the centrosome. In non-cycling cells, the centrosome is the template for primary cilia assembly and, thus, is crucial for their associated sensory and signaling functions. During mitosis, the duplicated centrosomes mature into spindle poles, which orchestrate mitotic spindle assembly, chromosome segregation, and orientation of the cell division axis. Intriguingly, both cilia and spindle poles are centrosome-based, functionally distinct structures that require the action of microtubule-mediated, motor-driven transport for their assembly. Cilia proteins have been found at non-cilia sites, where they have distinct functions, illustrating a diverse and growing list of cellular processes and structures that utilize cilia proteins for crucial functions. In this review, we discuss cilia-independent functions of cilia proteins and re-evaluate their potential contributions to "cilia" disorders. © 2015 The Authors.

Overview of North Ecliptic Pole Deep Multi-Wavelength Survey Nep-Deep

NASA Astrophysics Data System (ADS)

Matsuhara, H.; Wada, T.; Oi, N.; Takagi, T.; Nakagawa, T.; Murata, K.; Goto, T.; Oyabu, S.; Takeuchi, T. T.; Malek, K.; Solarz, A.; Ohyama, Y.; Miyaji, T.; Krumpe, M.; Lee, H. M.; Im, M.; Serjeant, S.; Pearson, C. P.; White, G. J.; Malkan, M. A.; Hanami, H.; Ishigaki, T.; Burgarella, D.; Buat, V.; Pollo, A.

2017-03-01

The recent updates of the North Ecliptic Pole deep (0.5~deg$^2$, NEP-Deep) multi-wavelength survey covering from X-ray to radio-wave is presented. The NEP-Deep provides us with several thousands of 15~$\\mu$m or 18~$\\mu$m selected sample of galaxies, which is the largest sample ever made at this wavelengths. A continuous filter coverage in the mid-infrared wavelength (7, 9, 11, 15, 18, and 24~$\\mu$m) is unique and vital to diagnose the contributions from starbursts and AGNs in the galaxies out to $z$=2.The new goal of the project is to resolve the nature of the cosmic star formation history at the violent epoch (e.g. $z$=1--2), and to find a clue to understand its decline from $z$=1 to present universe by utilizing the unique power of the multi-wavelength survey. The progress in this context is briefly mentioned.

Design, Synthesis, and Biological Evaluation of an Allosteric Inhibitor of HSET that Targets Cancer Cells with Supernumerary Centrosomes

PubMed Central

Watts, Ciorsdaidh A.; Richards, Frances M.; Bender, Andreas; Bond, Peter J.; Korb, Oliver; Kern, Oliver; Riddick, Michelle; Owen, Paul; Myers, Rebecca M.; Raff, Jordan; Gergely, Fanni; Jodrell, Duncan I.; Ley, Steven V.

2013-01-01

Summary Centrosomes associate with spindle poles; thus, the presence of two centrosomes promotes bipolar spindle assembly in normal cells. Cancer cells often contain supernumerary centrosomes, and to avoid multipolar mitosis and cell death, these are clustered into two poles by the microtubule motor protein HSET. We report the discovery of an allosteric inhibitor of HSET, CW069, which we designed using a methodology on an interface of chemistry and biology. Using this approach, we explored millions of compounds in silico and utilized convergent syntheses. Only compound CW069 showed marked activity against HSET in vitro. The inhibitor induced multipolar mitoses only in cells containing supernumerary centrosomes. CW069 therefore constitutes a valuable tool for probing HSET function and, by reducing the growth of cells containing supernumerary centrosomes, paves the way for new cancer therapeutics. PMID:24210220

PpNAC1, a main regulator of phenylalanine biosynthesis and utilization in maritime pine.

PubMed

Pascual, María Belén; Llebrés, María-Teresa; Craven-Bartle, Blanca; Cañas, Rafael A; Cánovas, Francisco M; Ávila, Concepción

2018-05-01

The transcriptional regulation of phenylalanine metabolism is particularly important in conifers, long-lived species that use large amounts of carbon in wood. Here, we show that the Pinus pinaster transcription factor, PpNAC1, is a main regulator of phenylalanine biosynthesis and utilization. A phylogenetic analysis classified PpNAC1 in the NST proteins group and was selected for functional characterization. PpNAC1 is predominantly expressed in the secondary xylem and compression wood of adult trees. Silencing of PpNAC1 in P. pinaster results in the alteration of stem vascular radial patterning and the down-regulation of several genes associated with cell wall biogenesis and secondary metabolism. Furthermore, transactivation and EMSA analyses showed that PpNAC1 is able to activate its own expression and PpMyb4 promoter, while PpMyb4 is able to activate PpMyb8, a transcriptional regulator of phenylalanine and lignin biosynthesis in maritime pine. Together, these results suggest that PpNAC1 is a functional ortholog of the ArabidopsisSND1 and NST1 genes and support the idea that key regulators governing secondary cell wall formation could be conserved between gymnosperms and angiosperms. Understanding the molecular switches controlling wood formation is of paramount importance for fundamental tree biology and paves the way for applications in conifer biotechnology. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Estimating Wood Volume for Pinus Brutia Trees in Forest Stands from QUICKBIRD-2 Imagery

NASA Astrophysics Data System (ADS)

Patias, Petros; Stournara, Panagiota

2016-06-01

Knowledge of forest parameters, such as wood volume, is required for a sustainable forest management. Collecting such information in the field is laborious and even not feasible in inaccessible areas. In this study, tree wood volume is estimated utilizing remote sensing techniques, which can facilitate the extraction of relevant information. The study area is the University Forest of Taxiarchis, which is located in central Chalkidiki, Northern Greece and covers an area of 58km2. The tree species under study is the conifer evergreen species P. brutia (Calabrian pine). Three plot surfaces of 10m radius were used. VHR Quickbird-2 images are used in combination with an allometric relationship connecting the Tree Crown with the Diameter at breast height (Dbh), and a volume table developed for Greece. The overall methodology is based on individual tree crown delineation, based on (a) the marker-controlled watershed segmentation approach and (b) the GEographic Object-Based Image Analysis approach. The aim of the first approach is to extract separate segments each of them including a single tree and eventual lower vegetation, shadows, etc. The aim of the second approach is to detect and remove the "noisy" background. In the application of the first approach, the Blue, Green, Red, Infrared and PCA-1 bands are tested separately. In the application of the second approach, NDVI and image brightness thresholds are utilized. The achieved results are evaluated against field plot data. Their observed difference are between -5% to +10%.

Complete genome sequence of Geobacillus strain Y4.1MC1, a novel CO-utilizing Geobacillus thermoglucosidasius strain isolated from Bath Hot Spring in Yellowstone National Park

DOE PAGES

Brumm, Phillip; Land, Miriam L.; Hauser, Loren John; ...

2015-02-10

Geobacillus thermoglucosidasius Y4.1MC1 was isolated from a boiling spring in the lower geyser basin of Yellowstone National Park. We present this species is of interest because of its metabolic versatility. The genome consists of one circular chromosome of 3,840,330 bp and a circular plasmid of 71,617 bp with an average GC content of 44.01%. The genome is available in the GenBank database (NC_014650.1 and NC_014651.1). In addition to the expected metabolic pathways for sugars and amino acids, the Y4.1MC1 genome codes for two separate carbon monoxide utilization pathways, an aerobic oxidation pathway and an anaerobic reductive acetyl CoA (Wood-Ljungdahl) pathway.more » This is the first report of a nonanaerobic organism with the Wood-Ljungdahl pathway. Also, this anaerobic pathway permits the strain to utilize H 2 and fix CO 2 present in the hot spring environment. Y4.1MC1 and its related species may play a significant role in carbon capture and sequestration in thermophilic ecosystems and may open up new routes to produce biofuels and chemicals from CO, H 2, and CO 2.« less

Complete genome sequence of Geobacillus strain Y4.1MC1, a novel CO-utilizing Geobacillus thermoglucosidasius strain isolated from Bath Hot Spring in Yellowstone National Park

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brumm, Phillip; Land, Miriam L.; Hauser, Loren John

Geobacillus thermoglucosidasius Y4.1MC1 was isolated from a boiling spring in the lower geyser basin of Yellowstone National Park. We present this species is of interest because of its metabolic versatility. The genome consists of one circular chromosome of 3,840,330 bp and a circular plasmid of 71,617 bp with an average GC content of 44.01%. The genome is available in the GenBank database (NC_014650.1 and NC_014651.1). In addition to the expected metabolic pathways for sugars and amino acids, the Y4.1MC1 genome codes for two separate carbon monoxide utilization pathways, an aerobic oxidation pathway and an anaerobic reductive acetyl CoA (Wood-Ljungdahl) pathway.more » This is the first report of a nonanaerobic organism with the Wood-Ljungdahl pathway. Also, this anaerobic pathway permits the strain to utilize H 2 and fix CO 2 present in the hot spring environment. Y4.1MC1 and its related species may play a significant role in carbon capture and sequestration in thermophilic ecosystems and may open up new routes to produce biofuels and chemicals from CO, H 2, and CO 2.« less

Method and apparatus for assembling a permanent magnet pole assembly

DOEpatents

Carl, Jr., Ralph James; Bagepalli, Bharat Sampathkumaran [Niskayuna, NY; Jansen, Patrick Lee [Scotia, NY; Dawson, Richard Nils [Voorheesville, NY; Qu, Ronghai [Clifton Park, NY; Avanesov, Mikhail Avramovich [Moscow, RU

2009-08-11

A pole assembly for a rotor, the pole assembly includes a permanent magnet pole including at least one permanent magnet block, a plurality of laminations including a pole cap mechanically coupled to the pole, and a plurality of laminations including a base plate mechanically coupled to the pole.

NASA's MESSENGER Finds New Evidence for Water Ice at Mercury's Poles

NASA Image and Video Library

2017-12-08

New observations by the MESSENGER spacecraft provide compelling support for the long-held hypothesis that Mercury harbors abundant water ice and other frozen volatile materials in its permanently shadowed polar craters. Three independent lines of evidence support this conclusion: the first measurements of excess hydrogen at Mercury's north pole with MESSENGER's Neutron Spectrometer, the first measurements of the reflectance of Mercury's polar deposits at near-infrared wavelengths with the Mercury Laser Altimeter (MLA), and the first detailed models of the surface and near-surface temperatures of Mercury's north polar regions that utilize the actual topography of Mercury's surface measured by the MLA. These findings are presented in three papers published online today in Science Express. Given its proximity to the Sun, Mercury would seem to be an unlikely place to find ice. But the tilt of Mercury's rotational axis is almost zero — less than one degree — so there are pockets at the planet's poles that never see sunlight. Scientists suggested decades ago that there might be water ice and other frozen volatiles trapped at Mercury's poles. The idea received a boost in 1991, when the Arecibo radio telescope in Puerto Rico detected unusually radar-bright patches at Mercury's poles, spots that reflected radio waves in the way one would expect if there were water ice. Many of these patches corresponded to the location of large impact craters mapped by the Mariner 10 spacecraft in the 1970s. But because Mariner saw less than 50 percent of the planet, planetary scientists lacked a complete diagram of the poles to compare with the images. MESSENGER's arrival at Mercury last year changed that. Images from the spacecraft's Mercury Dual Imaging System taken in 2011 and earlier this year confirmed that radar-bright features at Mercury's north and south poles are within shadowed regions on Mercury's surface, findings that are consistent with the water-ice hypothesis. To read more go to: 1.usa.gov/TtNwM2 Image Credit: NASA/Johns Hopkins University Applied Physics Laboratory/Carnegie Institution of Washington/National Astronomy and Ionosphere Center, Arecibo Observatory NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Improved ganoderic acids production in Ganoderma lucidum by wood decaying components

PubMed Central

Hu, Yanru; Ahmed, Shakeel; Li, Jiawei; Luo, Biaobiao; Gao, Zengyan; Zhang, Qiyun; Li, Xiaohua; Hu, Xuebo

2017-01-01

Ganoderma lucidum is a legendary Traditional Chinese Medicine (TCM) over a few thousands of years and one kind of its major active components are Ganoderic acids (GAs). GAs are largely produced in the mushroom primordium and fruiting body but much less in mycelium stage. However, little is known on the underlying regulatory mechanism. As a saprophytic fungus, G. lucidum solely obtains nutrients by wood decaying. Wood in general contains sophisticated chemical components with diverse structural units. To explore a strategy that extensively leads to GAs induction in the submerged liquid fermentation, all chemical components that might be possibly from the wood decaying were tested individually as GAs inducers. It was found that GAs production increased 85.96% by 1.5% microcrystalline cellulose (MCC) and 63.90% by 0.5% D-galactose. The transcription level of a few rate-limiting or chemically diverting enzymes responsible for GAs biosynthesis was greatly induced by MCC and D-galactose. The concentration and time-course titration study indicated that these two chemicals might not be utilized as carbon sources but they played a comprehensive role in the secondary metabolites synthesis. Our data indicated that MCC and D-galactose might be further industrialized for higher GAs production in G. lucidum in submerged fermentation. PMID:28422185

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Image and Video Library

1988-07-08

S88-42425 (20 July 1988) --- STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Three-dimensional characterization of the effective second-order nonlinearity in periodically poled crystals

NASA Astrophysics Data System (ADS)

Holmgren, Stefan J.; Pasiskevicius, Valdas; Wang, Shunhua; Laurell, Fredrik

2003-09-01

A novel technique for characterization of the second-order nonlinearity in nonlinear crystals is presented. It utilizes group-velocity walk-off between femtosecond pulses in type II SHG to achieve three-dimensional resolution of the nonlinearity. The longitudinal and transversal spatial resolution can be set independently. The technique is especially useful for characterizing quasi-phase-matched nonlinear crystals, and it is demonstrated in potassium titanyl phosphate.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. Covey has paddle-like gloves on his hands. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Longleaf pine regeneration following Hurricane Ivan utilizing the RLGS plots

Treesearch

John C. Gilbert; John S. Kush

2013-01-01

On September 16, 2004, Hurricane Ivan hit the Alabama coast and severely impacted numerous plots in the U.S. Forest Service’s Regional Longleaf Growth Study (RLGS). The Escambia Experimental Forest (EEF) has 201 of the 325 RLGS plots. Nearly one-third of the EEF was impacted. Nine plots with pole-sized trees were entirely lost. Another 54 plots had some type of damage...

KSC-2011-5975

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are NASA Panel Moderator and Public Affairs Officer George Diller (left), Jim Green, director of the Planetary Science Division at Headquarters in Washington, D.C.; Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods

KSC-2011-5972

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are NASA Panel Moderator and Public Affairs Officer George Diller (left), Jim Green, director of the Planetary Science Division at Headquarters in Washington, D.C.; Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods

KSC-2011-5971

NASA Image and Video Library

2011-07-25

CAPE CANAVERAL, Fla. -- In the Press Site auditorium at NASA's Kennedy Space Center in Florida, a briefing was held to update media on the upcoming launch of NASA's Juno spacecraft. Seen here are NASA Panel Moderator and Public Affairs Officer George Diller (left), Jim Green, director of the Planetary Science Division at Headquarters in Washington, D.C.; Scott Bolton, Juno principal investigator with the Southwest Research Institute in San Antonio, Texas; Jan Chodas, Juno project manager with the Jet Propulsion Laboratory in Pasadena, Calif., and Kaelyn Badura, Pine Ridge High School, Deltona, Fla. high school student, Juno Education program participant and Goldstone Apple Valley Radio Telescope Project participant. Juno is scheduled to launch aboard an United Launch Alliance Atlas V from Cape Canaveral, Fla. Aug. 5.The solar-powered spacecraft will orbit Jupiter's poles 33 times to find out more about the gas giant's origins, structure, atmosphere and magnetosphere and investigate the existence of a solid planetary core. For more information visit: www.nasa.gov/juno. Photo credit: NASA/Gianni M. Woods